WorldWideScience

Sample records for pure cerium dioxide

  1. Pure cerium dioxide preparation for use as spectrochemical standard and analysed by inductively coupled plasma mass spectrometry (SF ICP-MS)

    Energy Technology Data Exchange (ETDEWEB)

    Queiroz, Carlos A. da S.; Abrao, Alcidio; Rocha, Soraya M.R. da; Vasconcellos, Mari E. de; Seneda, Jose A.; Forbicini, Christina A.L.G. de O. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)]. E-mail: cqueiroz@ipen.br; Pedreira, Walter R.; Boaventura, Geraldo R. [Brasilia Univ., DF (Brazil). Dept. de Geociencias; Pimentel, Marcio M. [Fundacao Jorge Duprat Figueiredo de Seguranca e Medicina do Trabalho (FUNDACENTRO), Sao Paulo, SP (Brazil)]. E-mail: walter.pedreira@fundacentro.gov.br

    2005-11-15

    several years, IPEN/CNEN-SP has been working in the separation of the Rare Earth (RE) elements. A simple and economic procedure for the purification of technical grade cerium concentrate is described. The highly pure cerium dioxide is designed to be used as spectrochemical standard. It is obtained by association of the fractional precipitation technique, in the system RECl{sub 3}/NH{sub 4}OH/ Air/H{sub 2}O{sub 2}, to enrich the cerium up to 90% and then it is upgraded by ion exchange technique to 99.99% CeO{sub 2}. The quality control warranty was accomplished by inductively coupled mass spectrometry (ICP-MS) and neutron activation analysis. The collected values for the accompanying Rare Earth elements in a CeO{sub 2} sample are the following (ppm): La(36), Pr(19), Nd(161), Sm(11), Eu(5.3), Gd(113), Tb(89), Dy(2), Ho(0.05), Er(1), Tm(<0.05), Yb(11), Lu(19) and Y(2.1), respectively. The purity of this cerium oxide is comparable to the international spectrographic standards. (author)

  2. Ultrathin, epitaxial cerium dioxide on silicon

    Science.gov (United States)

    Flege, Jan Ingo; Kaemena, Björn; Höcker, Jan; Bertram, Florian; Wollschläger, Joachim; Schmidt, Thomas; Falta, Jens

    2014-03-01

    It is shown that ultrathin, highly ordered, continuous films of cerium dioxide may be prepared on silicon following substrate prepassivation using an atomic layer of chlorine. The as-deposited, few-nanometer-thin Ce2O3 film may very effectively be converted at room temperature to almost fully oxidized CeO2 by simple exposure to air, as demonstrated by hard X-ray photoemission spectroscopy and X-ray diffraction. This post-oxidation process essentially results in a negligible loss in film crystallinity and interface abruptness.

  3. Fire retardancy of emulsion polymerized poly (methyl methacrylate)/cerium(IV) dioxide and polystyrene/cerium(IV) dioxide nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Guipeng [Department of Chemistry and Fire Retardant Research Facility, Marquette University, PO Box 1881, Milwaukee, WI 53201 (United States); Lu, Hongdian [Department of Chemical and Materials Engineering, Hefei University, Hefei, Anhui 230022 (China); Zhou, You; Hao, Jianwei [School of Material Science and Engineering, Beijing Institute of Technology, Beijing 100081 (China); Wilkie, Charles A., E-mail: charles.wilkie@marquette.edu [Department of Chemistry and Fire Retardant Research Facility, Marquette University, PO Box 1881, Milwaukee, WI 53201 (United States)

    2012-12-10

    Highlights: Black-Right-Pointing-Pointer We prepare PMMA and PS containing ceria. Black-Right-Pointing-Pointer Characterization by XRD and TEM shows that some of the ceria is well-dispersed in the polymers. Black-Right-Pointing-Pointer The addition of ceria to both polymers leads to reduced thermal stability. Black-Right-Pointing-Pointer In PMMA, the fire retardancy is enhanced but there is little effect in PS. - Abstract: In situ emulsion polymerization was employed to obtain poly (methyl methacrylate) (PMMA)/cerium(IV) dioxide and polystyrene (PS)/cerium(IV) dioxide nanocomposites at two different cerium(IV) dioxide loadings (2.3 wt% and 4.6 wt%). Transmission electron microscope results indicated uniform dispersion of cerium (IV) dioxide in the polymer matrix. Both PMMA and PS nanocomposites exhibit lower thermal stability than the pristine polymers. Microscale combustion calorimeter (MCC) and cone calorimetry are used to evaluate the fire retardancy of the polymer nanocomposites. PMMA/cerium(IV) dioxide showed significant heat release rate (HRR) reduction at low loadings (<5 wt%), while PS/cerium(IV) dioxide exhibits less HRR reduction at the same loadings. An explanation of the role of cerium (IV) dioxide in fire retardancy of polymer/ceria nanocomposites based on XPS results is suggested.

  4. Determination of Impurity Elements in Pure Cerium Oxide Product

    Institute of Scientific and Technical Information of China (English)

    Li Peizhong; Chen Limin; Li Jie

    2004-01-01

    Determination of the rare earth impurity in pure cerium oxide is done by ICP-MS.The interference and other factors which affect analytical results were discussed.The accuracy are between 0.81% ~ 11.98% and the recoveries of standard addition are 96% ~ 112.5%.This method can meet the demand for product inspection.

  5. Cerium Dioxide Thin Films Using Spin Coating

    Directory of Open Access Journals (Sweden)

    D. Channei

    2013-01-01

    Full Text Available Cerium dioxide (CeO2 thin films with varying Ce concentrations (0.1 to 0.9 M, metal basis were deposited on soda-lime-silica glass substrates using spin coating. It was found that all films exhibited the cubic fluorite structure after annealing at 500°C for 5 h. The laser Raman microspectroscopy and GAXRD analyses revealed that increasing concentrations of Ce resulted in an increase in the degree of crystallinity. FIB and FESEM images confirmed the laser Raman and GAXRD analyses results owing to the predicted increase in film thickness with increasing Ce concentration. However, porosity and shrinkage (drying cracking of the films also increased significantly with increasing Ce concentrations. UV-VIS spectrophotometry data showed that the transmission of the films decreased with increasing Ce concentrations due to the increasing crack formation. Furthermore, a red shift was observed with increasing Ce concentrations, which resulted in a decrease in the optical indirect band gap.

  6. Molecular and physiological responses to titanium dioxide and cerium oxide nanoparticles in arabidopsis

    Science.gov (United States)

    - Changes in tissue transcriptomes and productivity of Arabidopsis thaliana were investigated during exposure of plants to two widely-used engineered metal oxide nanoparticles, titanium dioxide (nano-titanium) and cerium dioxide (nano-cerium). Microarray analyses confirmed that e...

  7. Molecular and physiological responses to titanium dioxide and cerium oxide nanoparticles in arabidopsis

    Science.gov (United States)

    - Changes in tissue transcriptomes and productivity of Arabidopsis thaliana were investigated during exposure of plants to two widely-used engineered metal oxide nanoparticles, titanium dioxide (nano-titanium) and cerium dioxide (nano-cerium). Microarray analyses confirmed that e...

  8. Cerium dioxide with large particle size prepared by continuous precipitation

    Institute of Scientific and Technical Information of China (English)

    李梅; 王觅堂; 柳召刚; 胡艳宏; 吴锦绣

    2009-01-01

    Cerium dioxide(CeO2) has attracted much attention and has wide applications such as automotive exhaust catalysts,polishing materials for optical glasses and additives for advanced glasses,as well as cosmetic materials.The particle size and its distribution are key factors to the performance of the materials in the functional applications.However,control of particle size is still a challenge in materials synthesis.Therefore,continuous precipitation of cerium oxalate(precursor of ceria) was carried out at dif...

  9. Molecular dynamics simulations of oxygen Frenkel pairs in cerium dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Shiiyama, Kenichi, E-mail: shiiyama@nucl.kyushu-u.ac.j [Department of Applied Quantum Physics and Nuclear Engineering, Kyushu University, Motooka 744, Nishi-ku, Fukuoka 819-0395 (Japan); Yamamoto, Tomokazu; Takahashi, Tatsuro [Department of Applied Quantum Physics and Nuclear Engineering, Kyushu University, Motooka 744, Nishi-ku, Fukuoka 819-0395 (Japan); Guglielmetti, Aurore; Chartier, Alain [CEA-Saclay, DEN/DPC/SCP, 91191 Gif-sur-Yvette (France); Yasuda, Kazuhiro; Matsumura, Syo; Yasunaga, Kazufumi [Department of Applied Quantum Physics and Nuclear Engineering, Kyushu University, Motooka 744, Nishi-ku, Fukuoka 819-0395 (Japan); Meis, Constantin [CEA-Saclay, INSTN, 91191 Gif-sur-Yvette (France)

    2010-10-01

    Molecular dynamics simulations of oxygen Frenkel pairs (FPs) in cerium dioxide (CeO{sub 2}) were carried out in order to understand their kinetic behavior. The results show that an oxygen FP recombine with the vacancy and the interstitial after the vacancy jump preferentially along the <1 0 0> direction. When multiple oxygen FPs are introduced, the interstitials aggregate into a (1 1 1) plate-like cluster at relatively lower temperature lower than 600 K, while they recombine with vacancies at elevated temperatures higher than 900 K within 10 ps. Molecular mechanics calculations of oxygen FPs on a (1 1 1) plane show that the formation energy per a FP decreases with increase of the number of FPs. The theoretical results are consistent with the transmission electron microscopy observations of formation of 1/9<1 1 1>{l_brace}1 1 1{r_brace} oxygen interstitial platelets in CeO{sub 2} under electron irradiation.

  10. Fate of cerium dioxide nanoparticles in endothelial cells: exocytosis

    Energy Technology Data Exchange (ETDEWEB)

    Strobel, Claudia, E-mail: Claudia.Strobel@med.uni-jena.de [Jena University Hospital – Friedrich Schiller University Jena, Department of Experimental Radiology, Institute of Diagnostic and Interventional Radiology (Germany); Oehring, Hartmut [Jena University Hospital – Friedrich Schiller University Jena, Institute of Anatomy II (Germany); Herrmann, Rudolf [University of Augsburg, Department of Physics (Germany); Förster, Martin [Jena University Hospital – Friedrich Schiller University Jena, Department of Internal Medicine I, Division of Pulmonary Medicine and Allergy/Immunology (Germany); Reller, Armin [University of Augsburg, Department of Physics (Germany); Hilger, Ingrid, E-mail: ingrid.hilger@med.uni-jena.de [Jena University Hospital – Friedrich Schiller University Jena, Department of Experimental Radiology, Institute of Diagnostic and Interventional Radiology (Germany)

    2015-05-15

    Although cytotoxicity and endocytosis of nanoparticles have been the subject of numerous studies, investigations regarding exocytosis as an important mechanism to reduce intracellular nanoparticle accumulation are rather rare and there is a distinct lack of knowledge. The current study investigated the behavior of human microvascular endothelial cells to exocytose cerium dioxide (CeO{sub 2}) nanoparticles (18.8 nm) by utilization of specific inhibitors [brefeldin A; nocodazole; methyl-β-cyclodextrin (MβcD)] and different analytical methods (flow cytometry, transmission electron microscopy, inductively coupled plasma mass spectrometry). Overall, it was found that endothelial cells were able to release CeO{sub 2} nanoparticles via exocytosis after the migration of nanoparticle containing endosomes toward the plasma membrane. The exocytosis process occurred mainly by fusion of vesicular membranes with plasma membrane resulting in the discharge of vesicular content to extracellular environment. Nevertheless, it seems to be likely that nanoparticles present in the cytosol could leave the cells in a direct manner. MβcD treatment led to the strongest inhibition of the nanoparticle exocytosis indicating a significant role of the plasma membrane cholesterol content in the exocytosis process. Brefeldin A (inhibitor of Golgi-to-cell-surface-transport) caused a higher inhibitory effect on exocytosis than nocodazole (inhibitor of microtubules). Thus, the transfer from distal Golgi compartments to the cell surface influenced the exocytosis process of the CeO{sub 2} nanoparticles more than the microtubule-associated transport. In conclusion, endothelial cells, which came in contact with nanoparticles, e.g., after intravenously applied nano-based drugs, can regulate their intracellular nanoparticle amount, which is necessary to avoid adverse nanoparticle effects on cells.

  11. Phenotypic and genomic responses to titanium dioxide and cerium oxide nanoparticles in Arabidopsis germinants

    Science.gov (United States)

    The effects of exposure to two nanoparticles (NPs) -titanium dioxide (nano-titania) and cerium oxide (nano-ceria) at 500 mg NPs L-1 on gene expression and growth in Arabidopsis thaliana germinants were studied using microarrays and phenotype studies. After 12 days post treatment,...

  12. The PL "violet shift" of cerium dioxide on silicon

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    CeO2 thin film was fabricated by dual ion beam epitaxial technique. The phenomenon of PL violet shift at room temperature was observed, and the distance of shift was about 65 nm. After the analysis of crystal structure and valence in the compound were carried out by XRD and XPS technique, it was concluded that the PL shift was related with valence of cerium ion in the oxides. When the valence of cerium ion varied from tetravalence to trivalence, the PL peak position would move from blue region to violet region and the phenomenon of "violet shift" was observed.

  13. Relationship between surface area and crystal size of pure and doped cerium oxides

    Institute of Scientific and Technical Information of China (English)

    C.; Bueno-Ferrer; S.; Parres-Esclapez; D.; Lozano-Castelló; A.; Bueno-López

    2010-01-01

    Pure and Zr, La or Pr-doped cerium oxides were characterised by transmission electron microscopy (TEM), N2 adsorption-desorption at -196 oC and X-ray diffraction (XRD). For crystal sizes calculation, the Scherrer and Williamson-Hall equations were compared, and the relationship between surface area and crystal size was critically discussed. It was demonstrated that the Williamson-Hall equation must be used instead of the Scherrer equation to calculate crystal sizes, since the latter equation underestimated ...

  14. Biocompatibility of cerium dioxide and silicon dioxide nanoparticles with endothelial cells

    Directory of Open Access Journals (Sweden)

    Claudia Strobel

    2014-10-01

    Full Text Available Cerium dioxide (CeO2 and silicon dioxide (SiO2 nanoparticles are of widespread use in modern life. This means that human beings are markedly exposed to them in their everyday life. Once passing biological barriers, these nanoparticles are expected to interact with endothelial cells, leading to systemic alterations with distinct influences on human health. In the present study we observed the metabolic impact of differently sized CeO2 (8 nm; 35 nm and SiO2 nanoparticles (117 nm; 315 nm on immortalized human microvascular (HMEC-1 and primary macrovascular endothelial cells (HUVEC, with particular focus on the CeO2 nanoparticles. The characterization of the CeO2 nanoparticles in cell culture media with varying serum content indicated a steric stabilization of nanoparticles due to interaction with proteins. After cellular uptake, the CeO2 nanoparticles were localized around the nucleus in a ring-shaped manner. The nanoparticles revealed concentration and time, but no size-dependent effects on the cellular adenosine triphosphate levels. HUVEC reacted more sensitively to CeO2 nanoparticle exposure than HMEC-1. This effect was also observed in relation to cytokine release after nanoparticle treatment. The CeO2 nanoparticles exhibited a specific impact on the release of diverse proteins. Namely, a slight trend towards pro-inflammatory effects, a slight pro-thrombotic impact, and an increase of reactive oxygen species after nanoparticle exposure were observed with increasing incubation time. For SiO2 nanoparticles, concentration- and time-dependent effects on the metabolic activity as well as pro-inflammatory reactions were detectable. In general, the effects of the investigated nanoparticles on endothelial cells were rather insignificant, since the alterations on the metabolic cell activity became visible at a nanoparticle concentration that is by far higher than those expected to occur in the in vivo situation (CeO2 nanoparticles: 100 µg/mL; SiO2

  15. Effect of oxygen defects on thermal conductivity of thorium-cerium dioxide solid solutions

    Science.gov (United States)

    Muta, Hiroaki; Kado, Hirohisa; Ohishi, Yuji; Kurosaki, Ken; Yamanaka, Shinsuke

    2017-01-01

    Thermal conductivity of thorium-cerium dioxide solid solutions has been measured and analyzed using the relaxation time approximation. Despite the presence of oxygen defects, the partially reduced Th0.8Ce0.2O1.97 exhibited higher thermal conductivity than the stoichiometric one, Th0.8Ce0.2O2.00, showing the same tendency as that previously reported for Th0.7Pu0.3O2-δ. The increase in thermal conductivity with the oxygen defects can be explained by assuming that cerium ions have an average ionic radius of the ionic radii of Ce3+ and Ce4+ in the description of phonon-impurity scattering. This result indicates that the small reduction of (Th,Pu)O2-δ fuel increases the thermal conductivity, especially at high temperatures.

  16. Germination and early plant development of ten plant species exposed to titanium dioxide and cerium oxide nanoparticles

    Science.gov (United States)

    Ten agronomic plant species were exposed to different concentrations of nano titanium dioxide (nTiO2) or nano cerium oxide (nCeO2) (0, 250, 500 and 1000 mg/L) to examine potential effects on germination and early seedling development. We modified a standard test protocol develop...

  17. [The changes of the motor function of the stomach and the colon under the action of the nanocrystalline cerium dioxide].

    Science.gov (United States)

    Iefimenko, O Iu; Savchenko, Iu O; Falalieieva, T M; Berehova, T V; Shcherbakov, O B; Ivanov, V K; Zholobak, N M; Maliukin, Iu V; Spivak, M Ia

    2014-01-01

    We investigated the effect of nanocrystalline cerium dioxide on parameters of spontaneous and stimulated motility of the stomach and colon in rats. It was found that administration of nanocrystalline cerium dioxide for 10 days increased the amplitude of contractions of stimulated motility in the stomach by 33.0 +/- 2.4% and the frequency of contractions of the colon by 80.3 +/- 7.5%. In this group, the introduction of carbachol also increased the frequency of the contractions by 274.0 +/- 22.9%, compared to the control group. The administration of nanocrystalline cerium dioxide increased the index of motor activity of spontaneous and stimulated motility of the stomach by 19.8 +/- 1.4 and 14.5 +/- 9.0%, respectively. In the colon, the motor activity increased by 14.3 +/- 1.1 and 11.1 +/- 0.8%, respectively. We also found that the nanocrystalline cerium dioxide rebuilt morphological condition of the mucous of the colon.

  18. Nanocrystalline cerium dioxide efficacy for prophylaxis of erosive and ulcerative lesions in the gastric mucosa of rats induced by stress.

    Science.gov (United States)

    Golyshkin, Dmytro; Kobyliak, Nazarii; Virchenko, Oleksandr; Falalyeyeva, Tetyana; Beregova, Tetyana; Ostapchenko, Lyudmyla; Caprnda, Martin; Skladany, Lubomir; Opatrilova, Radka; Rodrigo, Luis; Kruzliak, Peter; Shcherbokov, Alexandr; Spivak, Mykola

    2016-12-01

    In our previous works, the important therapeutic properties of nanocrystalline cerium dioxide such as strong antioxidant ability, prebiotical and antibiotic activity were shown. Such properties were obtained due to stabilization of nanoparticles with precise size 3-7nm. Such modification of nanocrystalline cerium dioxide has contributed to its remarkable efficacy and low toxicity. We have carried out the investigation of toxicity of the nanodrug and revealed that in the condition of the acute toxicity test, LD 50 was 2000mg/kg when it was administered per os. This indicator is approximately 1000 times greater than effective dose of the compound that proved the possibility of its usage for humans. Considering the strong antioxidant properties of this substance, we have performed the investigation of the influence of nanocrystalline cerium dioxide on the erosive-ulcerative lesions in gastric mucosa of rats induced by Selye's restraint stress. It was established that the studied compound significantly reduced the lesions area by 58.3% (p<0.05) induced by Selye's restraint stress. The attenuation of inflammation and decrease of lipid peroxidation in the conditions of gastric lesions and prophylactic administration of nanocrystalline cerium dioxide were shown. That was confirmed by the decrease of pro-inflammatory cytokines content (interleukin (IL) 1β, 12B p40) and raise of anti-inflammatory cytokines content (IL-10 and transforming growth factor β). Measurement of lipid peroxidation products has proved the antioxidant properties of nanocrystalline cerium dioxide as it decreased the content of conjugated dienes and thiobarbituric acid active products in the conditions of gastric ulceration induced by stress.

  19. Preparation and properties of a cerium-containing hydroxyapatite coating on commercially pure titanium by micro-arc oxidation

    Institute of Scientific and Technical Information of China (English)

    HUANG Yong; WANG Yingjun; NING Chengyun; NAN Kaihui; HAN Yong

    2008-01-01

    A porous cerium-containing hydroxyapatite coating on commercially pure titanium was prepared by micro-arc oxidation (MAO) in an electrolytic solution containing calcium acetate, β-glycerol phosphate disodium salt pentahydrate (β-GP), and cerium nitrate. The thickness, phase, composition morphology, and biocompatibility of the oxide coating were characterized by X-ray diffraction (XRD), electron probe microanalysis (EPMA), scanning electron microscopy (SEM) with energy dispersive X-ray spectrometer (EDS), and cell culture. The thickness of the MAO film is about 15-25μm, and the coating is porous and uneven, without any apparent interface to the titanium substrates. The results of XRD and EDS show that the porous coating is made up of hydroxyapatite (HA) film containing Ce. The favorable osteoblast cell affinity makes the Ce-HA film have a good biocompatibility. The Ce-HA film is expected to have significant medical applications as dental implants and artificial bone joints.

  20. Comparison of lead dioxide and cerium dioxide as mediators for carbon paste electrodes in flow injection-amperometric detection of hydrogen peroxide

    OpenAIRE

    Mihić-Necin, Bojana; Guzsvány, Valéria; Kalcher, Kurt

    2010-01-01

    Carbon paste electrodes (graphite / paraffin oil), bulk-modified with lead dioxide and cerium dioxide, were used as sensors for the amperometric determination of hydrogen peroxide in flow injection analysis. Experimental parameters, such as applied working potential, flow rate of the carrier and injection volume were optimized with a thin-layer flow-through cell. The method was validated with respect to calibration curve, linear dynamic range, detection limit, repeatability and...

  1. Ultrastructural Interactions and Genotoxicity Assay of Cerium Dioxide Nanoparticles on Mouse Oocytes

    Directory of Open Access Journals (Sweden)

    Blandine Courbiere

    2013-10-01

    Full Text Available Cerium dioxide nanoparticles (CeO2 ENPs are on the priority list of nanomaterials requiring evaluation. We performed in vitro assays on mature mouse oocytes incubated with CeO2 ENPs to study (1 physicochemical biotransformation of ENPs in culture medium; (2 ultrastructural interactions with follicular cells and oocytes using Transmission Electron Microscopy (TEM; (3 genotoxicity of CeO2 ENPs on follicular cells and oocytes using a comet assay. DNA damage was quantified as Olive Tail Moment. We show that ENPs aggregated, but their crystal structure remained stable in culture medium. TEM showed endocytosis of CeO2 ENP aggregates in follicular cells. In oocytes, CeO2 ENP aggregates were only observed around the zona pellucida (ZP. The comet assay revealed significant DNA damage in follicular cells. In oocytes, the comet assay showed a dose-related increase in DNA damage and a significant increase only at the highest concentrations. DNA damage decreased significantly both in follicular cells and in oocytes when an anti-oxidant agent was added in the culture medium. We hypothesise that at low concentrations of CeO2 ENPs oocytes could be protected against indirect oxidative stress due to a double defence system composed of follicular cells and ZP.

  2. Use of boiled hexamethylenetetramine and urea to increase the porosity of cerium dioxide microspheres formed in the internal gelation process

    Science.gov (United States)

    Hunt, R. D.; Collins, J. L.; Cowell, B. S.

    2017-08-01

    Cerium dioxide (CeO2) is a commonly used simulant for plutonium dioxide and for plutonium (Pu) in uranium (U) and Pu oxide [(U, Pu)O2] mixtures used in nuclear fuel development. This effort developed CeO2 microspheres with a various porosities and diameters. The internal gelation technique has only been used to produce CeO2 microspheres with limited initial porosity. Previous studies have shown that the crystallite size and porosity of mixed U and thorium oxide microspheres and the (U, Pu)O2 microspheres from the internal gelation process increased when an equal molar solution of hexamethylenetetramine (HMTA) and urea is gently boiled for 1 h prior to its use in the gelation process. In this study with cerium, the combination of ammonium cerium nitrate and 1-h boiled HMTA-urea failed to produce a stable feed broth. However, when the 1-h heated HMTA-urea was combined with unheated HMTA-urea in 1-3 vol ratio or the boiling time of the HMTA-urea was reduced to 15-20 min, a stable solution of HMTA, urea, and Ce was formed at 273 K. This new Ce solution produced very porous CeO2 microspheres, which are suitable simulants for uranium microspheres.

  3. Cerium dioxide nanoparticles possess anti-inflammatory properties in the conditions of the obesity-associated NAFLD in rats.

    Science.gov (United States)

    Kobyliak, Nazarii; Virchenko, Oleksandr; Falalyeyeva, Tetyana; Kondro, Maryana; Beregova, Tetyana; Bodnar, Petro; Shcherbakov, Oleksandr; Bubnov, Rostyslav; Caprnda, Martin; Delev, Delian; Sabo, Jan; Kruzliak, Peter; Rodrigo, Luis; Opatrilova, Radka; Spivak, Mykola

    2017-06-01

    Obesity is a risk factor for non-alcoholic fatty liver disease (NAFLD). The disease is associated with impairment of pro/antioxidant equilibrium and the inflammation in liver tissue. The aim of the work was to investigate the anti-inflammatory properties of the nanocrystalline cerium dioxide (nCeO2) on the rat model of NAFLD associated with monosodium glutamate (MSG)-induced obesity. The study was carried out on three groups of rats: control, MSG- and MSG+nCeO2. They were injected with saline (control) or MSG. A month after born MSG-rats had been treated with water in a volume of 2.9ml/kg, MSG+CeO2 groups - with CeO2 intragastrically (i.g.). The anthropometric and carbohydrate metabolism parameters, content of proinflammatory cytokines (interleukin (IL)-1β, IL-12Bp40, interferon-γ (INF-γ)) and anti-inflammatory cytokines (IL-4, IL-10, tumor growth factor-β (TGF-β)) were measured by ELISA. We have demonstrated the anti-obesity effect of nanocrystalline cerium dioxide and for the first time its anti-inflammatory properties. Nanoparticles reduced the content of pro-inflammatory cytokines (IL-1β, IL-12Bp40) in rat serum and restored the level of anti-inflammatory cytokines (IL-4, IL-10, TGF-β) to the control values. The precise mechanisms of this phenomenon remain to be unclear but we suppose they are at least partially associated with the strong anti-oxidant action of studied substance. Nanocrystalline cerium dioxide attenuates the inflammatory processes in rat blood that can prevent obesity complications and liver injury. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  4. Cerium dioxide as a new reactive sorbent for fast degradation of parathion methyl and some other organophosphates

    Institute of Scientific and Technical Information of China (English)

    Pavel Janos; Lubos Vrtoch; Pavel Kuran; Martin Kormunda; Vaclav Stengl; Tomas Matys Grygar; Marek Dosek; Martin Stastny; Jakub Ederer; Vera Pilarova

    2014-01-01

    Cerium dioxide was used for the first time as reactive sorbent for the degradation of the organophosphate pesticides para-thion methyl, chlorpyrifos, dichlofenthion, fenchlorphos, and prothiofos, as well as of some chemical warfare agents-nerve gases soman and O-ethyl S-[2-(diisopropylamino) ethyl] methylphosphonothioate (VX). CeO2 specimens were prepared by calcination of basic cerous carbonate obtained by precipitation from an aqueous solution. The CeO2 samples containing certain amounts (1 wt.%-5 wt.%) of the neighboring lanthanides (La, Pr, Nd) were prepared in a similar way from pure lanthanide salts. It was shown that ceria accelerated markedly the decomposition of parathion methyl causing the cleavage of the P-O-aryl bond in the pesticide molecule. A similar reaction mechanism was proposed for the degradation of other organophosphate pesticides and nerve agents. The degradation times (reaction half-times) were in an order of minutes in the presence of CeO2, compared to hours or days under common environ-mental conditions. The reaction in suitable organic solvents allowed conversions of about 90%for parathion methyl loading of 20 mg pesticide/g CeO2 within 2 h with a reactant half-life in the order of 0.1 min. The key parameter governing the degradation efficiency of CeO2 was the temperature during calcination. At optimum calcination temperature (about 773.15 K), the produced ceria retained a sufficiently high surface area, and attained an optimum degree of crystallinity (related to a number of crystal defects, and thus poten-tial reactive sites). The presence of other lanthanides somewhat decreased the reaction rate, but this effect was not detrimental and permitted the possible use of chemically impure ceria as a reactive sorbent. A fast organophosphate degradation was demonstrated not only in non-polar solvents (such as heptane), but also in polar aprotic solvents (acetonitrile, acetone) that are miscible with water. This opens new possibilities for

  5. Cerium dioxide nanoparticle exposure improves microvascular dysfunction and reduces oxidative stress in spontaneously hypertensive rats

    Directory of Open Access Journals (Sweden)

    Valerie C Minarchick

    2015-11-01

    Full Text Available The elevated production of reactive oxygen species (ROS in the vascular wall is associated with cardiovascular diseases such as hypertension. This increase in oxidative stress contributes to various mechanisms of vascular dysfunction, such as decreased nitric oxide bioavailability. Therefore, anti-oxidants are being researched to decrease the high levels of ROS, which could improve the microvascular dysfunction associated with various cardiovascular diseases. From a therapeutic perspective, cerium dioxide nanoparticles (CeO2 NP hold great anti-oxidant potential, but their in vivo activity is unclear. Due to this potential anti-oxidant action, we hypothesize that injected CeO2 NP would decrease microvascular dysfunction and oxidative stress associated with hypertension. In order to simulate a therapeutic application, spontaneously hypertensive (SH and Wistar-Kyoto (WKY rats were intravenously injected with either saline or CeO2 NP (100 µg suspended in saline. Twenty-four hours post-exposure mesenteric arteriolar reactivity was assessed via intravital microscopy. Endothelium-dependent and –independent function was assessed via acetylcholine and sodium nitroprusside. Microvascular oxidative stress was analyzed using fluorescent staining in isolated mesenteric arterioles. Finally, systemic inflammation was examined using a multiplex analysis and venular leukocyte flux was counted. Endothelium-dependent dilation was significantly decreased in the SH rats (29.68 ± 3.28%, maximal response and this microvascular dysfunction was significantly improved following CeO2 NP exposure (43.76 ± 4.33%, maximal response. There was also an increase in oxidative stress in the SH rats, which was abolished following CeO2 NP treatment. These results provided evidence that CeO2 NP act as an anti-oxidant in vivo. There were also changes in the inflammatory profile in the WKY and SH rats. In WKY rats, IL-10 and TNF-α were increased following CeO2 NP treatment

  6. Adsorption behavior of lead on aquatic sediments contaminated with cerium dioxide nanoparticles.

    Science.gov (United States)

    Wang, Chao; Fan, Xiulei; Wang, Peifang; Hou, Jun; Ao, Yanhui; Miao, Lingzhan

    2016-12-01

    Aquatic sediments serve as an important sink for engineered nanomaterials (ENMs), such as metal oxide nanoparticles (MeO NPs) and carbon nanotubes (CNTs). Owing to their remarkable properties, ENMs demonstrate significant potential to disturb the adsorption behavior of other contaminants in aquatic sediments, thereby altering the bioavailability and toxicity of these contaminants. Thus far, most studies have investigated the effect of CNTs on the adsorption of other contaminants on sediments. Cerium dioxide nanoparticles (CeO2 NPs), as one of the important MeO NPs, are also inevitably discharged into aquatic sediments because of their widespread use. In this study, we investigated the adsorption behavior of Pb(2+) on sediments spiked with CeO2 NPs at a weight ratio of 5.0%. The results showed that the adsorption rates at three stages occurring during adsorption clearly increase for sediments contaminated with CeO2 NPs. Moreover, the results obtained from the adsorption isotherms indicated that the Langmuir isotherm model best fits the isotherm data for both sediments and those contaminated with CeO2 NPs. After spiking the sediments with CeO2 NPs, the theoretical maximum monolayer adsorption capacity (Qmax) for Pb(2+) increased from 4.433 to 4.995 mg/g and the Langmuir isotherm coefficient (KL) decreased from 8.813 to 7.730 L/g. The effects of CeO2 NPs on the surface charge and pore surface properties of sediments were also studied as these properties affect the adsorption of several chemicals in sediments. The results showed that pHzpc, SBET, Sext, and average pore size of sediments clearly decrease for sediments contaminated with CeO2 NPs. Hence, the strong adsorption capacity of CeO2 NPs and the changes of sediment surface charge and pore surface properties caused by CeO2 NPs are important factors affecting the adsorption behavior of Pb(2+). The potential risk of Pb(2+) in aquatic environment may increase with CeO2 NPs buried in sediments.

  7. Boundary effects on the electrical conductivity of pure and doped cerium oxide thin films.

    Science.gov (United States)

    Göbel, Marcus C; Gregori, Giuliano; Guo, Xiangxin; Maier, Joachim

    2010-11-14

    Thin films of CeO(2) (both nominally pure and 10 mol% gadolinium-doped) grown via pulsed-laser deposition were studied. The electrical conductivity of the samples was measured as a function of thickness, temperature and oxygen partial pressure (pO(2)) using impedance spectroscopy. As expected, undoped CeO(2) exhibits electronic conductivity (with activation energy between 1.4 and 1.6 eV) whereas the highly doped samples are oxygen vacancy conductors (activation energy around 0.7 eV for epitaxial films). In order to investigate the influence of the nature of the substrate the thin films were grown on two different substrates, Al(2)O(3) (0001) and SiO(2) (0001), and compared. While the films grown on SiO(2) exhibit a microstructure characterized by columnar grains, the films grown on Al(2)O(3) are epitaxial. Notably, for films on both substrates the conductivity and activation energy vary with film thickness and exhibit remarkable differences when the films on different substrates are compared. In the case of the polycrystalline films (SiO(2) substrate), the space charge layer effects of the grain boundaries dominate over the substrate-film interface effect. In the case of the epitaxial films (Al(2)O(3) substrate), a small interface effect, probably due to a space charge layer or structural strain, is observed.

  8. Water Quality Impacts of Pure Chlorine Dioxide Pretreatment at the Roanoke County (Virginia) Water Treatment Plant

    OpenAIRE

    Ellenberger, Christine Spada

    1999-01-01

    WATER QUALITY IMPACTS OF PURE CHLORINE DIOXIDE PRETREATMENT AT THE ROANOKE COUNTY (VIRGINIA) WATER TREATMENT PLANT by Christine S. Ellenberger Dr. Robert C. Hoehn, Chairman (ABSTRACT) Chlorine dioxide (ClO2) was included in the Spring Hollow Water Treatment Plant (Roanoke County, Virginia) to oxidize manganese and iron, prevent tastes and odors, and avoid the formation of excessive halogenated disinfection by-products. A state-of-the-art, gas:solid ClO2 generation system ...

  9. Study of the catalytic activity of pure or cerium-containing thoria in the catalytic oxidation of carbon monoxide (1963); Etude de l'activite catalytique de la thorine pure ou contenant du cerium. Dans l'oxydation de l'oxyde de carbone (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Veron, J. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    We have undertaken research into the oxidation of carbon monoxide on pure thoria prepared by the decomposition of thorium nitrate, and on the same oxide containing small amounts of cerium. The results we have obtained, both as concerns the chemisorption of the various gases as well as the conductivity of the absorbent and the kinetics of the oxidation itself, appear to be quite coherent. The following steps occur: 1) The carbon monoxide is adsorbed on a clean catalyst surface, the oxygen remaining un-adsorbed. 2) The oxygen is adsorbed on a previously adsorbed carbon, monoxide layer, and reacts to give carbon dioxide (no role being played by the lattice oxygen). This behaviour is usual for a p-type semiconductor. We have in fact confirmed that semi-conductivity is of this type, and the gas-solid interactions can be written: (1) CO{sub (g)} {r_reversible} CO{sup +}{sub (a)} + e{sup -} (2) CO{sup +} 1/2 O{sub 2(g)} + 2 e{sup -} {yields} CO{sup -}{sub 2(a)} (3) CO{sup -}{sub 2(a)} {r_reversible} CO{sub 2(g)} + e{sup -} The kinetic equation obtained by supposing that step (2) is the slowest, makes it possible to deduce correctly the experimental results which can be expressed as: dp / dt = k (P{sup 0.3}{sub CO} x P{sup 0.5}{sub O{sub 2}}) / (1+ k' x P{sub CO{sub 2}}) The influence of the addition of small amounts of cerium can also be explained logically by this process; there is in fact both a decrease in the conductivity and an increase in the catalytic activity, this being characteristic, according to VOLKENSTEIN [52] of an n-type rate-determining reaction occurring on a p-type semi-conductor. We believe that these first results could be advantageously complemented by a study of thoria prepared by other means and doped differently. (author) [French] Nous avons entrepris l'etude de l'oxydation de l'oxyde de carbone sur la thorine pure preparee par decomposition du nitrate de thorium, et sur le meme oxyde renfermant de petites quantites de cerium

  10. Exposure and Health Effects Review of Engineered Nanoscale Cerium and Cerium Dioxide Associated with its Use as a Fuel Additive - NOW IN PRINT IN THE JOURNAL

    Science.gov (United States)

    Advances of nanoscale science have produced nanomaterials with unique physical and chemical properties at commercial levels that are now incorporated into over 1000 products. Nanoscale cerium (di) oxide (Ce02) has recently gained a wide range of applications which includes coatin...

  11. Mobility of nanosized cerium dioxide and polymeric capsules in quartz and loamy sands saturated with model and natural groundwaters.

    Science.gov (United States)

    Petosa, Adamo Riccardo; Ohl, Carolin; Rajput, Faraz; Tufenkji, Nathalie

    2013-10-01

    The environmental and health risks posed by emerging engineered nanoparticles (ENPs) released into aquatic environments are largely dependent on their aggregation, transport, and deposition behavior. Herein, laboratory-scale columns were used to examine the mobility of polyacrylic acid (PAA)-coated cerium dioxide nanoparticles (nCeO2) and an analogous nanosized polymeric capsule (nCAP) in water saturated quartz sand or loamy sand. The influence of solution ionic strength (IS) and cation type (Na(+), Ca(2+), or Mg(2+)) on the transport potential of these ENPs was examined in both granular matrices and results were also compared to measurements obtained using a natural groundwater. ENP suspensions were characterized using dynamic light scattering and nanoparticle tracking analysis to establish aggregate size, and laser Doppler electrophoresis to determine ENP electrophoretic mobility. Regardless of IS, virtually all nCeO2 particles suspended in NaNO3 eluted from the quartz sand-packed columns. In contrast, heightened nCeO2 and nCAP particle retention and dynamic (time-dependent) transport behavior was observed with increasing concentrations of the divalent salts and in the presence of natural groundwater. Enhanced particle retention was also observed in loamy sand in comparison to the quartz sand, emphasizing the need to consider the nature of the aqueous matrix and granular medium in evaluating contamination risks associated with the release of ENPs in natural and engineered aquatic environments.

  12. Thermoluminescence and sintering of ultra-pure {alpha} alumina doped with zirconium, thorium, calcium or cerium; Thermoluminescence et frittage de l'alumine {alpha} ultra-pure dopee par le zirconium, le thorium, le calcium, ou le cerium

    Energy Technology Data Exchange (ETDEWEB)

    Ferey, F

    2002-01-01

    Thermoluminescence is a technique of identification of the point defects that appear in a solid consecutively to its fabrication. The synthesis parameters of {alpha}-alumina that will be taken into account here are the atmosphere during thermal treatment (oxidising or reducing), and the effect of the dopants: zirconium, thorium, calcium or cerium. The aim of this work is to correlate the point defects to the reactivity of the powder, especially its sintering. The TL mechanisms of the dosimetric peak of {alpha}-alumina, around 200 deg C, were clarified: the trap is an aggregate of 2 point defects (V{sub al}-V{sub O}), and the recombination centre is Cr{sup 3+}. The sensibilizing effect observed for thorium, or for cerium under reducing atmosphere, is attributed to the presence of a large emission band in the blue-green domain. Chromium is the main impurity at the origin of the E' peak (360 deg C) of {alpha}-alumina. It is acting as trap and also as recombination centre. A mechanism of transfer of energy between Cr{sup 3+} and Ti{sup 4+} is also presented in order to explain the increase of the TL intensity of the E' peak when doping by a tetravalent cation. In the case of doping by calcium, TL allows the revelation of the phase CaAl{sub 12}O{sub 19}. A quenching was observed for {alpha}Al{sub 2}O{sub 3}:Ca and {alpha}Al{sub 2}O{sub 3}:Ce under reducing atmosphere. It is attributed to oxygen vacancies for the doping by calcium, and to the presence of Ce{sup 3+} for the doping by cerium. The alumina prepared under reducing conditions exhibit a perturbation of kinetics during sintering, and also abnormal grain growth in doped samples. This unusual kinetic is explained by a decrease in the concentration of aluminium vacancies under reducing atmosphere, conducting indirectly to a greater segregation of Si{sup 4+} at the grain boundaries, and to the formation of a liquid phase at the surface of grains. This phenomenon is amplified in the case of doping by

  13. Pure germanium dioxide hollow-core fiber for transmitting CO2 laser

    Institute of Scientific and Technical Information of China (English)

    侯兰田; 付连符; 吕平; 韩玉华; 李秋更; 徐立宣; 李天柱

    1995-01-01

    A method of fabricating pure germanium dioxide hollow-core fibers has been introduced for the first time. The output power of the fabricated fiber can come to 18 W, with the transmission loss of 1.23 dB/m at 10.6 μm. The mechanism of transmitting CO2 laser by the fiber is analyzed, the transmitting loss is further discussed and its application fields are envisaged.

  14. Evaluation of titanium dioxide and cerium oxide as anodes for the electrooxidation of toluene A theoretical approach of the electrode process

    Energy Technology Data Exchange (ETDEWEB)

    D' Elia, Luis F.; Rincon, L.; Ortiz, R

    2004-09-30

    Cerium oxide and titanium dioxide were prepared by thermal decomposition of the precursor salts and thermal treatment of titanium plates. In aqueous medium, the metal oxides show a well-defined electrochemical reaction; a solid state redox process takes place in the cathodic range of potentials and only water discharge reaction occurs in the anodic region. At the experimental conditions, the prepared materials were not totally active for the electrooxidation of toluene. The theoretical modeling suggests that the lack of activity is due to the weak interaction between toluene and the metal oxide surface.

  15. Microwave synthesis of pure and doped cerium (IV) oxide (CeO2) nanoparticles for methylene blue degradation.

    Science.gov (United States)

    El Rouby, W M A; Farghali, A A; Hamdedein, A

    2016-11-01

    Cerium (IV) oxide (CeO2), samarium (Sm) and gadolinium (Gd) doped CeO2 nanoparticles were prepared using microwave technique. The effect of microwave irradiation time, microwave power and pH of the starting solution on the structure and crystallite size were investigated. The prepared nanoparticles were characterized using X-ray diffraction, FT-Raman spectroscopy, and transmission electron microscope. The photocatalytic activity of the as-prepared CeO2, Sm and Gd doped CeO2 toward degradation of methylene blue (MB) dye was investigated under UV light irradiation. The effect of pH, the amount of catalyst and the dye concentration on the degradation extent were studied. The photocatalytic activity of CeO2 was kinetically enhanced by trivalent cation (Gd and Sm) doping. The results revealed that Gd doped CeO2 nanoparticles exhibit the best catalytic degradation activity on MB under UV irradiation. For clarifying the environmental safety of the by products produced from the degradation process, the pathways of MB degradation were followed using liquid chromatography/mass spectroscopy (LC/MS). The total organic carbon content measurements confirmed the results obtained by LC/MS. Compared to the same nanoparticles prepared by another method, it was found that Gd doped CeO2 prepared by hydrothermal process was able to mineralize MB dye completely under UV light irradiation.

  16. Bioelectrochemical reduction of carbon dioxide by pure culture at the cathode

    DEFF Research Database (Denmark)

    Aryal, Nabin; Tremblay, Pier-Luc; Chen, Leifeng

    2014-01-01

    Microbial electrosynthesis (MES) is an innovative approach in which microbes use electricity toreduce carbon dioxide and produce chemical commodities. This process relies on the ability of electroautotrophic microbes to accept electron from an electrode. The concept of MES has already been...... demonstrated with pure cultures of acetogenic bacteria such as Sporomusa ovate DSM-2662 and Clostridium ljungdahlii. Until now, electron transfer rates from the cathode to the bestelectroautotroph, S. ovata, are still orders of magnitude lower than what is observed in bioanodicprocesses with electrigenic...... bacteria. Hence, we are screening other pure cultures for better MES activities. These bacterial species were pre-selected based on several criteria such as their presence in enrichments of environmental samples in MES systems, their capacity to fix CO2, their incapacity to sporulate, and their ability...

  17. Multiple-diffusion flame synthesis of pure anatase and carbon-coated titanium dioxide nanoparticles

    KAUST Repository

    Memon, Nasir

    2013-09-01

    A multi-element diffusion flame burner (MEDB) is useful in the study of flame synthesis of nanomaterials. Here, the growth of pure anatase and carbon-coated titanium dioxide (TiO2) using an MEDB is demonstrated. Hydrogen (H2), oxygen (O2), and argon (Ar) are utilized to establish the flame, whereas titanium tetraisopropoxide is used as the precursor for TiO2. The nanoparticles are characterized using high-resolution transmission electron microscopy, with elemental mapping (of C, O, and Ti), X-ray diffraction, Raman spectroscopy, and thermogravimetric analysis. The growth of pure anatase TiO2 nanoparticles occurs when Ar and H2 are used as the precursor carrier gas, while the growth of carbon-coated nanoparticles ensues when Ar and ethylene (C2H4) are used as the precursor carrier gas. A uniform coating of 3-5nm of carbon is observed around TiO2 particles. The growth of highly crystalline TiO2 nanoparticles is dependent on the gas flow rate of the precursor carrier and amorphous particles are observed at high flow rates. Carbon coating occurs only on crystalline nanoparticles, suggesting a possible growth mechanism of carbon-coated TiO2 nanoparticles. © 2013 The Combustion Institute.

  18. Nano-cerium-element-doped titanium dioxide induces apoptosis of Bel 7402 human hepatoma cells in the presence of visible light

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    AIM: To investigate the apoptotic effect of photoexcited titanium dioxide (TiO2) nanoparticles in the presence of visible light on human hepatoma cell line (Bel 7402) and to study the underlying mechanism.METHODS: Cerium-element-doped titanium dioxide nanoparticles were prepared by impregnation method.Bel 7402 human hepatoma cells were cultured in RPMI 1640 medium in a humidified incubator with 50 mL/L CO2 at 37℃. A 15 W fluorescent lamp with continuous wavelength light was used as light source in the photocatalytic test. Fluorescence morphology and agarose gel eletrophoresis pattern were performed to analyze apoptotic cells.RESULTS: The Ce (Ⅳ)-doped TiO2 nanoparticles displayed their superiority, The adsorption edge shifted to the 400-450 nm region. With visible light illuminated for 10 min, 10 μg/cm3 Ce (Ⅳ)-doped TiO2 induced micronuclei and significant apoptosis in 4 and 24 h,respectively. Hochest 33258 staining of the fixed cells revealed typical apoptotic structures (apoptotic bodies),agarose gel electrophoresis showed typical DNA ladder pattern in treated cells but not in untreated ones.CONCLUSION: Ce (Ⅳ) doped TiO2 nanoparticles can induce apoptosis of Bel 7402 human hepatoma cells in the presence of visible light.

  19. Effects of cerium dioxide nanoparticles in Oncorhynchus mykiss gills after an acute exposure: assessment of oxidative stress, genotoxicity and histological alterations

    Directory of Open Access Journals (Sweden)

    Alberto Teodorico Correia

    2015-12-01

    Full Text Available Data about the toxicological effects of cerium dioxide nanoparticles (CeO2 NP in fish are scarce. This work aimed to assess the CeO2 NP possible deleterious effects on the gills of Oncorhynchus mykiss. A semi-continuous acute test was conducted to expose the rainbow trout to a freshwater control, 0.25, 2.50 and 25.00 mg/L CeO2 NPs for up to 96 hours. Gills pathological index showed a dose-effect relationship for the individuals exposed to CeO2. Gills showed aneurisms, epithelial lifting and hyperplasia. Furthermore exposure to CeO2 NPs caused statistical differences in some biomarkers determinations, namely a significant increase in the catalase activity and genotoxicity the higher concentrations. No significant changes were however observed in thiobarbituric acid reactive substances content, Na+-K+ ATPase and glutathione s-transferase activities. This study suggests that CeO2 nanoparticles are toxic compounds that can lead to histological, biochemical and genotoxic alterations.

  20. Long term effects of cerium dioxide nanoparticles on the nitrogen removal, micro-environment and community dynamics of a sequencing batch biofilm reactor.

    Science.gov (United States)

    Xu, Yi; Wang, Chao; Hou, Jun; Wang, Peifang; Miao, Lingzhan; You, Guoxiang; Lv, Bowen; Yang, Yangyang; Zhang, Fei

    2017-09-01

    The influences of cerium dioxide nanoparticles (CeO2 NPs) on nitrogen removal in biofilm were investigated. Prolonged exposure (75d) to 0.1mg/L CeO2 NPs caused no inhibitory effects on nitrogen removal, while continuous addition of 10mg/L CeO2 NPs decreased the treatment efficiency to 53%. With the progressive concentration of CeO2 NPs addition, the removal efficiency could nearly stabilize at 67% even with the continues spike of 10mg/L. The micro-profiles of dissolved oxygen, pH, and oxidation reduction potential suggested the developed protection mechanisms of microbes to progressive CeO2 NPs exposure led to the less influence of microenvironment, denitrification bacteria and enzyme activity than those with continuous ones. Furthermore, high throughput sequencing illustrated the drastic shifted communities with gradual CeO2 NPs spiking was responsible for the adaption and protective mechanisms. The present study demonstrated the acclimated microbial community was able to survive CeO2 NPs addition more readily than those non-acclimated. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. [THE INFLUENCE OF NANODISPERSE CERIUM DIOXIDE ON ONTOGENETIC CHANGES OF ANTIOXIDANT SYSTEM IN THE MUCOSA OF THE STOMACH AND COLON IN RATS].

    Science.gov (United States)

    Iefimenko, O Yu; Savchenko, I O; Falalyeyeva, T M; Beregova, T V; Zholobak, N M; Shcherbakov, O B; Malyukin, Yu V; Spivak, M Ya

    2015-01-01

    It was established that with age the content of lipid peroxidation products increased in the mucosa of the stomach: Diene conjugates by 30%, products which react to thiobarbituric acid by 285% and Schif bases by 181%. Nanodisperse cerium dioxide (NCD) reduced the content of lipid peroxidation in the gastric mucosa in old rats: Diene conjugates by 43 %, products which react to thiobarbituric acid by 51% and Schif bases by 44% relative to the control group of rats given age. Similarly, it was established that the content of Diene conjugates increased by 40%, products which react to thiobarbituric acid by 114% and Schif bases by 132% in the mucosa of the colon of old rats. NDC significant reduced the content of products which react to thiobarbituric acid by 69% and Schyf basics by 132%. In the stomach superoxide dismutase (by 43%) and catalase activity (by 24%) decreases with age, while in the colon superoxide dismutase activity increases (by 43%). In the colon NCD significant decreased superoxide dismutase (by 34%) and catalase activity (by 21%) relative to controls. Thus, the NDC restores lipid peroxidation in the gastric mucosa and colon, in which develops oxidative stress with age.

  2. Study on photocatalytic performance of cerium-graphene oxide-titanium dioxide composite film for formaldehyde removal

    Energy Technology Data Exchange (ETDEWEB)

    Li, Jia; Zhang, Quan [The Civil Engineering College of Hunan University, Changsha (China); Lai, Alvin C.K. [Department of Civil and Architectural Engineering, City University of Hong Kong, Kowloon (China); Zeng, Liping [Department of Building Engineering of Hunan Institute of Engineering, Xiangtan (China)

    2016-12-15

    In order to degrade in-car formaldehyde gas, graphene oxide (GO), cerium (Ce), and TiO{sub 2} were organically combined by one-step sol-gel method. Then the mixed collosol was coated onto the surface of inorganic glass substrates to form Ce-GO-TiO{sub 2} composite film by way of immersion, coating, and calcinations. The morphology and crystal structure of as-prepared Ce-GO-TiO{sub 2} film were studied by a series of detection techniques. The photocatalytic performance of this film was analyzed by the degradation effect of formaldehyde under simulated sunlight. The results showed that the Ce-GO-TiO{sub 2} film had the inbuilt mesoporous structure in the lamellar stacking with particles. When the doping amount of Ce and GO were 0.4 and 0.2% (mass ratio), the composite film can improve effectively the response to the visible light and its degradation rate for low concentration of formaldehyde was up to 83.8% in simulated sunlight for 7 h, which could be attributed to the co-function of Ce and GO. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. Recovery of Cerium Dioxide from Spent Glass-Polishing Slurry and Its Utilization as a Reactive Sorbent for Fast Degradation of Toxic Organophosphates

    Directory of Open Access Journals (Sweden)

    Pavel Janoš

    2015-01-01

    Full Text Available The recovery of cerium (and possibly other rare earth elements from the spent glass-polishing slurries is rather difficult because of a high resistance of polishing-grade cerium oxide toward common digestion agents. It was shown that cerium may be extracted from the spent polishing slurries by leaching with strong mineral acids in the presence of reducing agents; the solution may be used directly for the preparation of a ceria-based reactive sorbent. A mixture of concentrated nitric acid and hydrogen peroxide was effective in the digestion of partially dewatered glass-polishing slurry. After the removal of undissolved particles, cerous carbonate was precipitated by gaseous NH3 and CO2. Cerium oxide was prepared by a thermal decomposition of the carbonate precursor in an open crucible and tested as reactive sorbent for the degradation of highly toxic organophosphate compounds. The samples annealed at the optimal temperature of approximately 400°C exhibited a good degradation efficiency toward the organophosphate pesticide fenchlorphos and the nerve agents soman and VX. The extraction/precipitation procedure recovers approximately 70% of cerium oxide from the spent polishing slurry. The presence of minor amounts of lanthanum does not disturb the degradation efficiency.

  4. Modification of pure oxygen absorption equipment for concurrent stripping of carbon dioxide

    Science.gov (United States)

    Watten, B.J.; Sibrell, P.L.; Montgomery, G.A.; Tsukuda, S.M.

    2004-01-01

    The high solubility of carbon dioxide precludes significant desorption within commercial oxygen absorption equipment. This operating characteristic of the equipment limits its application in recirculating water culture systems despite its ability to significantly increase allowable fish loading rates (kg/(L min)). Carbon dioxide (DC) is typically removed by air stripping. This process requires a significant energy input for forced air movement, air heating in cold climates and water pumping. We developed a modification for a spray tower that provides for carbon dioxide desorption as well as oxygen absorption. Elimination of the air-stripping step reduces pumping costs while allowing dissolved nitrogen to drop below saturation concentrations. This latter response provides for an improvement in oxygen absorption efficiency within the spray tower. DC desorption is achieved by directing head-space gases from the spray tower (O2, N2, CO2) through a sealed packed tower scrubber receiving a 2 N NaOH solution. Carbon dioxide is selectively removed from the gas stream, by chemical reaction, forming the product Na 2CO3. Scrubber off-gas, lean with regard to carbon dioxide but still rich with oxygen, is redirected through the spray tower for further stripping of DC and absorption of oxygen. Make-up NaOH is metered into the scrubbing solution sump on an as needed basis as directed by a feedback control loop programmed to maintain a scrubbing solution pH of 11.4-11.8. The spent NaOH solution is collected, then regenerated for reuse, in a batch process that requires relatively inexpensive hydrated lime (Ca(OH)2). A by-product of the regeneration step is an alkaline filter cake, which may have use in bio-solids stabilization. Given the enhanced gas transfer rates possible with chemical reaction, the required NaOH solution flow rate through the scrubber represents a fraction of the spray tower water flow rate. Further, isolation of the water being treated from the atmosphere (1

  5. Literature Survey on the Effects of Pure Carbon Dioxide on Health, Comfort and Performance

    DEFF Research Database (Denmark)

    Zhang, Xiaojing; Wargocki, Pawel; Lian, Zhiwei

    2014-01-01

    Carbon dioxide (CO2) is one of the components of the earth atmosphere. It is also a significant human metabolite. It is colourless and odourless gas. The background levels of CO2 in ambient air are about 350-400 ppm. Its concentration in buildings can be an order of magnitude higher reaching even 4...... in buildings (Pettenkofer, 1858), as well as quantity and effectiveness of ventilation in the presence of people; the levels above 1,000 ppm have been generally considered to cause unacceptable air quality; the levels above 2,000 ppm are considered as the levels requiring actionable decisions. The 8-hour...

  6. Improving Settling Characteristics of Pure Oxygen Activated Sludge by Stripping of Carbon Dioxide.

    Science.gov (United States)

    Kundral, Somshekhar; Mudragada, Ratnaji; Coro, Ernesto; Moncholi, Manny; Mora, Nelson; Laha, Shonali; Tansel, Berrin

    2015-06-01

    Increased microbial activity at high ambient temperatures can be problematic for secondary clarifiers and gravity concentrators due to carbon dioxide (CO2) production. Production of CO2 in gravity concentrators leads to septic conditions and poor solids separation. The CO2 production can also be corrosive for the concrete surfaces. Effectiveness of CO2 stripping to improve solids settling was investigated using the sludge volume index (SVI) as the indicator parameter. Carbon dioxide was stripped by aeration from the sludge samples. Results from the study show that aeration also increased the pH values in the mixed liquor while removing CO2 and improving sludge settling. After 10 minutes of aeration at a rate of 0.37 m3 air/m3 water/min, 90% CO2 stripping was achieved. Based on the 30 min settling tests, the SVI increased by 26±1% after CO2 stripping while the pH increased by 0.8±0.1 pH units.

  7. Adsorption of Pure Methane, Nitrogen, and Carbon Dioxide and Their Mixtures on San Juan Basin Coal

    Energy Technology Data Exchange (ETDEWEB)

    K. A. M. Gasem; R. L. Robinson; S. R. Reeves

    2002-03-01

    The major objectives of this project were to (a) measure the adsorption behavior of pure methane, nitrogen, CO{sub 2} and their binary and ternary mixtures on wet Tiffany coal at 130 F and pressures to 2000 psia; (b) correlate the equilibrium adsorption isotherm data using the extended Langmuir model, the Langmuir model, the loading ratio correlation and the Zhou-Gasem-Robinson equation of state; and (c) establish sorption-time estimates for the pure components. Specific accomplishments are summarized below regarding the complementary tasks involving experimental work and data correlation. Representative coal samples from BP Amoco Tiffany Injection Wells No.1 and No.10 were prepared, as requested. The equilibrium moisture content and particle size distribution of each coal sample were determined. Compositional coal analyses for both samples were performed by Huffman Laboratories, Inc. Pure gas adsorption for methane on wet Tiffany coal samples from Injection Wells No.1 and No.10 was measured separately at 130 F (327.6 K) and pressures to 2000 psia (13.7 MPa). The average expected uncertainty in these data is about 3% (9 SCF/ton). Our measurements indicate that the adsorption isotherms of the two coal samples exhibit similar Langmuir-type behavior. For the samples from the two wells, a maximum variation of about 5% in the amount adsorbed is observed at 2000 psia. Gas adsorption isotherms were measured for pure methane, nitrogen and CO{sub 2} on a wet, mixed Tiffany coal sample. The coal sample was an equal-mass mixture of coals from Well No.1 and Well No.10. The adsorption measurements were conducted at 130 F at pressures to 2000 psia. The adsorption isotherms have average expected experimental uncertainties of 3% (9 SCF/ton), 6% (8 SCF/ton), and 7% (62 SCF/ton) for methane, nitrogen, and CO{sub 2}, respectively. Adsorption isotherms were measured for methane/nitrogen, methane/CO{sub 2} and nitrogen/CO{sub 2} binary mixtures on wet, mixed Tiffany coal at 130 F and

  8. Co-doping of Iron and Cerium in Titanium Dioxide: Observation of a Cooperative Effect%铁和铈共掺杂二氧化钛中的协同效应

    Institute of Scientific and Technical Information of China (English)

    李哓俊; 司德君; 方均; 姜志全; 黄伟新

    2006-01-01

    The co-doping of iron and cerium into TiO2 was studied by means of X-ray diffraction, Raman spectroscopy,UV-Vis diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy, when separately doping via the sol-gel method, iron was introduced in the framework of anatase TiO2 whereas cerium was not;interestingly, both iron and cerium were introduced in the framework when co-doping by the sol-gel method.The co-doped TiO2 behaves much more intense surface hydroxyl concentration than the separately-doped and pure TiO2. This observation demonstrates for the first time a cooperative effect in the co-doping of transitional metals in the framework of TiO2.%利用X射线衍射、拉曼光谱、紫外-可见漫反射光谱和X射线光电子能谱研究了铁和铈对TiO2的共掺杂.当利用溶胶-凝胶法进行单独掺杂时,铁离子可以进入锐钛矿TiO2骨架,但铈离子却不能进入TiO2骨架;当铁和铈共掺杂时,铁离子和铈离子可以同时进入TiO2骨架.铁-铈共掺杂的TiO2表面羟基浓度要远高于单独掺杂或者纯的TiO2.第一次观察到过渡金属离子共掺杂进入TiO2骨架的协同效应.

  9. Sap flux in pure aspen and mixed aspen-birch forests exposed to elevated concentrations of carbon dioxide and ozone.

    Science.gov (United States)

    Uddling, Johan; Teclaw, Ronald M; Kubiske, Mark E; Pregitzer, Kurt S; Ellsworth, David S

    2008-08-01

    Elevated concentrations of atmospheric carbon dioxide ([CO2]) and tropospheric ozone ([O3]) have the potential to affect tree physiology and structure and hence forest water use, which has implications for climate feedbacks. We investigated how a 40% increase above ambient values in [CO2] and [O3], alone and in combination, affect tree water use of pure aspen and mixed aspen-birch forests in the free air CO2-O3 enrichment experiment near Rhinelander, Wisconsin (Aspen FACE). Measurements of sap flux and canopy leaf area index (L) were made during two growing seasons, when steady-state L had been reached after more than 6 years of exposure to elevated [CO2] and [O3]. Maximum stand-level sap flux was not significantly affected by elevated [O3], but was increased by 18% by elevated [CO2] averaged across years, communities and O(3) regimes. Treatment effects were similar in pure aspen and mixed aspen-birch communities. Increased tree water use in response to elevated [CO2] was related to positive CO2 treatment effects on tree size and L (+40%). Tree water use was not reduced by elevated [O3] despite strong negative O3 treatment effects on tree size and L (-22%). Elevated [O3] predisposed pure aspen stands to drought-induced sap flux reductions, whereas increased tree water use in response to elevated [CO2] did not result in lower soil water content in the upper soil or decreasing sap flux relative to control values during dry periods. Maintenance of soil water content in the upper soil in the elevated [CO2] treatment was at least partly a function of enhanced soil water-holding capacity, probably a result of increased organic matter content from increased litter inputs. Our findings that larger trees growing in elevated [CO2] used more water and that tree size, but not maximal water use, was negatively affected by elevated [O3] suggest that the long-term cumulative effects on stand structure may be more important than the expected primary stomatal closure responses to

  10. Multibiomarker assessment of cerium dioxide nanoparticle (nCeO{sub 2}) sublethal effects on two freshwater invertebrates, Dreissena polymorpha and Gammarus roeseli

    Energy Technology Data Exchange (ETDEWEB)

    Garaud, M. [Université de Lorraine, CNRS UMR 7360, Laboratoire Interdisciplinaire des Environnements Continentaux (LIEC), Campus Bridoux, Rue du Général Delestraint, 57070 Metz (France); International Consortium for the Environmental Implications of Nanotechnology (iCEINT), Aix en Provence (France); Trapp, J.; Devin, S.; Cossu-Leguille, C.; Pain-Devin, S.; Felten, V. [Université de Lorraine, CNRS UMR 7360, Laboratoire Interdisciplinaire des Environnements Continentaux (LIEC), Campus Bridoux, Rue du Général Delestraint, 57070 Metz (France); Giamberini, L., E-mail: laure.giamberini@univ-lorraine.fr [Université de Lorraine, CNRS UMR 7360, Laboratoire Interdisciplinaire des Environnements Continentaux (LIEC), Campus Bridoux, Rue du Général Delestraint, 57070 Metz (France); International Consortium for the Environmental Implications of Nanotechnology (iCEINT), Aix en Provence (France)

    2015-01-15

    Highlights: • Gammarids and mussels both accumulated significant amount of waterborne nCeO{sub 2}. • nCeO{sub 2} decreased catalase, lysosomal system size and lipoperoxidation in mussels. • nCeO{sub 2} could exert antioxidant protecting activity in mussels. • In contrast with mussels, no effects of nCeO{sub 2} were observed on Gammarids. - Abstract: Cerium nanoparticles (nCeO{sub 2}) are widely used in everyday products, as fuel and paint additives. Meanwhile, very few studies on nCeO{sub 2} sublethal effects on aquatic organisms are available. We tried to fill this knowledge gap by investigating short-term effects of nCeO{sub 2} at environmentally realistic concentrations on two freshwater invertebrates; the amphipod Gammarus roeseli and the bivalve Dreissena polymorpha, using an integrated multibiomarker approach to detect early adverse effects of nCeO{sub 2} on organism biology. Differences in the behaviour of the organisms and of nanoparticles in the water column led to differential nCeO{sub 2} bioaccumulations, G. roeseli accumulating more cerium than D. polymorpha. Exposure to nCeO{sub 2} led to decreases in the size of the lysosomal system, catalase activity and lipoperoxidation in mussel digestive glands that could result from nCeO{sub 2} antioxidant properties, but also negatively impacted haemolymph ion concentrations. At the same time, no strong adverse effects of nCeO{sub 2} could be observed on G. roeseli. Further experiments will be necessary to confirm the absence of severe nCeO{sub 2} adverse effects in long-term environmentally realistic conditions.

  11. Cerium anomaly at microscale in fossils.

    Science.gov (United States)

    Gueriau, Pierre; Mocuta, Cristian; Bertrand, Loïc

    2015-09-01

    Patterns in rare earth element (REE) concentrations are essential instruments to assess geochemical processes in Earth and environmental sciences. Excursions in the "cerium anomaly" are widely used to inform on past redox conditions in sediments. This proxy resources to the specificity of cerium to adopt both the +III and +IV oxidation states, while most rare earths are purely trivalent and share very similar reactivity and transport properties. In practical terms, the level of cerium anomaly is established through elemental point quantification and profiling. All these models rely on a supposed homogeneity of the cerium oxidation state within the samples. However, this has never been demonstrated, whereas the cerium concentration can significantly vary within a sample, as shown for fossils, which would vastly complicate interpretation of REE patterns. Here, we report direct micrometric mapping of Ce speciation through synchrotron X-ray absorption spectroscopy and production of local rare earth patterns in paleontological fossil tissues through X-ray fluorescence mapping. The sensitivity of the approach is demonstrated on well-preserved fishes and crustaceans from the Late Cretaceous (ca. 95 million years (Myr) old). The presence of Ce under the +IV form within the fossil tissues is attributed to slightly oxidative local conditions of burial and agrees well with the limited negative cerium anomaly observed in REE patterns. The [Ce(IV)]/[Ce(tot)] ratio appears remarkably stable at the microscale within each fossil and is similar between fossils from the locality. Speciation maps were obtained from an original combination of synchrotron microbeam X-ray fluorescence, absorption spectroscopy, and diffraction, together with light and electron microscopy. This work also highlights the need for more systematic studies of cerium geochemistry at the microscale in paleontological contexts, in particular across fossil histologies.

  12. Environmental Geochemistry of Cerium: Applications and Toxicology of Cerium Oxide Nanoparticles

    OpenAIRE

    2015-01-01

    Cerium is the most abundant of rare-earth metals found in the Earth’s crust. Several Ce-carbonate, -phosphate, -silicate, and -(hydr)oxide minerals have been historically mined and processed for pharmaceutical uses and industrial applications. Of all Ce minerals, cerium dioxide has received much attention in the global nanotechnology market due to their useful applications for catalysts, fuel cells, and fuel additives. A recent mass flow modeling study predicted that a major source of CeO2 na...

  13. Effects of cerium dioxide nanoparticles in Oncorhynchus mykiss liver after an acute exposure: assessment of oxidative stress, genotoxicity and histological alterations

    Directory of Open Access Journals (Sweden)

    Ana Cristina Nunes

    2015-12-01

    Full Text Available At present cerium oxide nanoparticles (CeO2 NP have numerous applications ranging from industry to the household, leading to its wide distribution namely in the aquatic environment. The hereby study aimed to assess the toxic effects of CeO2 NPs in Oncorhynchus mykiss liver following an acute exposure (96h to three different concentrations (0.25, 2.5 and 25 mg/L in terms of the genotoxicity (comet assay, oxidative stress response (Catalase CAT; Glutathione S-Transferases GSTs; Thiobarbituric Acid Reactive Substances TBARS and histopathology. CeO2 NP exposure resulted in genotoxic damage in all exposure treatments, inhibition of CAT in the highest concentration and histopathological changes in all exposure concentrations with predominance of progressive and circulatory alterations. However TBARS and GSTs showed no significant differences comparatively to the control (unexposed group. The results suggest that CeO2 NP are able to cause genotoxicity, biochemical impairment and histological alterations in the liver of rainbow trout.

  14. Reaction chemistry of cerium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-01-01

    It is truly ironic that a synthetic organic chemist likely has far greater knowledge of the reaction chemistry of cerium(IV) than an inorganic colleague. Cerium(IV) reagents have long since been employed as oxidants in effecting a wide variety of organic transformations. Conversely, prior to the late 1980s, the number of well characterized cerium(IV) complexes did not extend past a handful of known species. Though in many other areas, interest in the molecular chemistry of the 4f-elements has undergone an explosive growth over the last twenty years, the chemistry of cerium(IV) has for the most part been overlooked. This report describes reactions of cerium complexes and structure.

  15. Reaction chemistry of cerium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-01-01

    It is truly ironic that a synthetic organic chemist likely has far greater knowledge of the reaction chemistry of cerium(IV) than an inorganic colleague. Cerium(IV) reagents have long since been employed as oxidants in effecting a wide variety of organic transformations. Conversely, prior to the late 1980s, the number of well characterized cerium(IV) complexes did not extend past a handful of known species. Though in many other areas, interest in the molecular chemistry of the 4f-elements has undergone an explosive growth over the last twenty years, the chemistry of cerium(IV) has for the most part been overlooked. This report describes reactions of cerium complexes and structure.

  16. Kinetic studies on dissolution of UO{sub 2} powders in acid solutions by using cerium (IV) or chlorine dioxide as oxidants

    Energy Technology Data Exchange (ETDEWEB)

    Asano, Yuichiro; Kataoka, Makoto; Tomiyasu, Hiroshi [Tokyo Inst. of Tech. (Japan). Research Lab. for Nuclear Reactors; Ikeda, Yasuhisa

    1996-02-01

    The UO{sub 2} powders of 100-150, 150-212, 212-250, and 250-300 {mu}m were dissolved in HNO{sub 3} or HCl solutions containing strong oxidants to examine their effect on the dissolution rates. Cerium(IV) species and ClO{sub 2} were used as oxidants in HNO{sub 3} and HCl solutions, respectively. The Ce(IV) species were prepared by bubbling O{sub 3} gas into HNO{sub 3} solutions containing Ce(NO{sub 3}){sub 3}. All dissolution experiments were carried out under rapid stirring conditions which make it possible to neglect the diffusion effect. Dissolution reactions were analyzed on the assumptions that the UO{sub 2} powders are spherical particles and homogeneously dissolved from their external surface. Dissolution rate constants ({Phi}) in mol{center_dot}cm{sup -2}{center_dot}min{sup -1} were measured at various concentrations of oxidants and temperatures. Furthermore, the effect of acid concentrations on the dissolution rate was also examined. As a result, the dissolution rate constants {Phi} were found to be expressed as {Phi}=k{sub N}[Ce(IV)][H{sup +}]{sup 0.6} for HNO{sub 3} solution([HNO{sub 3}]=1-5M, Temp.{<=}30degC) and {Phi}=k{sub H}[ClO{sub 2}][H{sup +}]{sup -0.3} for HCl solution([HCl]=1-5M, Temp.{<=}30degC), respectively. Activation energies(kJ{center_dot}mol{sup -1}) for the apparent dissolution rate constants are 44.1{+-}1.9 for the HNO{sub 3} solution system and 33.5{+-}2.8 for the HCl solution system, respectively. (author).

  17. Comparing the efficacy of hyper-pure chlorine-dioxide with other oral antiseptics on oral pathogen microorganisms and biofilm in vitro.

    Science.gov (United States)

    Herczegh, Anna; Gyurkovics, Milán; Agababyan, Hayk; Ghidán, Agoston; Lohinai, Zsolt

    2013-09-01

    This study examines the antibacterial properties of sodium hypochlorite (NaOCl), chlorhexidine gluconate (CHX), Listerine®, and high purity chlorine dioxide (Solumium, ClO2) on selected common oral pathogen microorganisms and on dental biofilm in vitro. Antimicrobial activity of oral antiseptics was compared to the gold standard phenol. We investigated Streptococcus mutans, Lactobacillus acidophilus, Enterococcus faecalis, Veillonella alcalescens, Eikenella corrodens, Actinobacillus actinomycetemcomitans and Candida albicans as some important representatives of the oral pathogens. Furthermore, we collected dental plaque from the upper first molars of healthy young students. Massive biofilm was formed in vitro and its reduction was measured after treating it with mouthrinses: CHX, Listerine® or hyper pure ClO2. Their biofilm disrupting effect was measured after dissolving the crystal violet stain from biofilm by photometer. The results have showed that hyper pure ClO2 solution is more effective than other currently used disinfectants in case of aerobic bacteria and Candida yeast. In case of anaerobes its efficiency is similar to CHX solution. The biofilm dissolving effect of hyper pure ClO2 is significantly stronger compared to CHX and Listerine® after 5 min treatment. In conclusion, hyper pure ClO2 has a potent disinfectant efficacy on oral pathogenic microorganisms and a powerful biofilm dissolving effect compared to the current antiseptics, therefore high purity ClO2 may be a new promising preventive and therapeutic adjuvant in home oral care and in dental or oral surgery practice.

  18. Size-mediated cytotoxicity of nanocrystalline titanium dioxide, pure and zinc-doped hydroxyapatite nanoparticles in human hepatoma cells

    Energy Technology Data Exchange (ETDEWEB)

    Devanand Venkatasubbu, G.; Ramasamy, S., E-mail: sinna_ramasamy@yahoo.com [Crystal Growth Centre, Anna University (India); Avadhani, G. S. [Indian Institute of Science, Department of Materials Engineering (India); Palanikumar, L.; Kumar, J. [Crystal Growth Centre, Anna University (India)

    2012-03-15

    Nanoparticles are highly used in biological applications including nanomedicine. In this present study, the interaction of HepG2 hepatocellular carcinoma cells (HCC) with hydroxyapatite (HAp), zinc-doped hydroxyapatite, and titanium dioxide (TiO{sub 2}) nanoparticles were investigated. Hydroxyapatite, zinc-doped hydroxyapatite and titanium dioxide nanoparticles were prepared by wet precipitation method. They were subjected to isochronal annealing at different temperatures. Particle morphology and size distribution were characterized by X-ray diffraction and transmission electron microscope. The nanoparticles were co-cultured with HepG2 cells. MTT assay was employed to evaluate the proliferation of tumor cells. The DNA damaging effect of HAp, Zn-doped HAp, and TiO{sub 2} nanoparticles in human hepatoma cells (HepG2) were evaluated using DNA fragmentation studies. The results showed that in HepG2 cells, the anti-tumor activity strongly depend on the size of nanoparticles in HCC cells. Cell cycle arrest analysis for HAp, zinc-doped HAp, and TiO{sub 2} nanoparticles revealed the influence of HAp, zinc-doped HAp, and titanium dioxide nanoparticles on the apoptosis of HepG2 cells. The results imply that the novel nano nature effect plays an important role in the biomedicinal application of nanoparticles.

  19. Study of cerium diffusion in undoped lithium-6 enriched glass with Rutherford backscattering spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xiaodong, E-mail: xzhang39@utk.edu [Department of Nuclear Engineering, University of Tennessee, TN 37996 (United States); Moore, Michael E.; Lee, Kyung-Min; Lukosi, Eric D. [Department of Nuclear Engineering, University of Tennessee, TN 37996 (United States); Hayward, Jason P. [Department of Nuclear Engineering, University of Tennessee, TN 37996 (United States); Oak Ridge National Lab, Oak Ridge, TN 37831 (United States)

    2016-07-01

    Undoped lithium-6 enriched glasses coated with pure cerium (99.9%) with a gold protection layer on top were heated at three different temperatures (500, 550, and 600 °C) for varied durations (1, 2, and 4 h). Diffusion profiles of cerium in such glasses were obtained with the conventional Rutherford backscattering technique. Through fitting the diffusion profiles with the thin-film solution of Fick’s second law, diffusion coefficients of cerium with different annealing temperatures and durations were solved. Then, the activation energy of cerium for the diffusion process in the studied glasses was found to be 114 kJ/mol with the Arrhenius equation.

  20. Study of cerium diffusion in undoped lithium-6 enriched glass with Rutherford backscattering spectrometry

    Science.gov (United States)

    Zhang, Xiaodong; Moore, Michael E.; Lee, Kyung-Min; Lukosi, Eric D.; Hayward, Jason P.

    2016-07-01

    Undoped lithium-6 enriched glasses coated with pure cerium (99.9%) with a gold protection layer on top were heated at three different temperatures (500, 550, and 600 °C) for varied durations (1, 2, and 4 h). Diffusion profiles of cerium in such glasses were obtained with the conventional Rutherford backscattering technique. Through fitting the diffusion profiles with the thin-film solution of Fick's second law, diffusion coefficients of cerium with different annealing temperatures and durations were solved. Then, the activation energy of cerium for the diffusion process in the studied glasses was found to be 114 kJ/mol with the Arrhenius equation.

  1. Probing the cerium/cerium hydride interface using nanoindentation

    Energy Technology Data Exchange (ETDEWEB)

    Brierley, Martin, E-mail: martin.brierley@awe.co.uk [Atomic Weapons Establishment, Aldermaston, Berkshire RG7 4PR (United Kingdom); University of Manchester, Manchester M13 9PL (United Kingdom); Knowles, John, E-mail: john.knowles@awe.co.uk [Atomic Weapons Establishment, Aldermaston, Berkshire RG7 4PR (United Kingdom)

    2015-10-05

    Highlights: • A disparity exists between the minimum energy and actual shape of a cerium hydride. • Cerium hydride is found to be harder than cerium metal by a ratio of 1.7:1. • A zone of material under compressive stress was identified surrounding the hydride. • No distribution of hardness was apparent within the hydride. - Abstract: A cerium hydride site was sectioned and the mechanical properties of the exposed phases (cerium metal, cerium hydride, oxidised cerium hydride) were measured using nanoindentation. An interfacial region under compressive stress was observed in the cerium metal surrounding a surface hydride that formed as a consequence of strain energy generated by the volume expansion associated with precipitation of the hydride phase.

  2. Antioxidative effects of cerium dioxide nanoparticles ameliorate age-related male infertility: optimistic results in rats and the review of clinical clues for integrative concept of men health and fertility.

    Science.gov (United States)

    Kobyliak, Nazarii M; Falalyeyeva, Tetyana M; Kuryk, Olena G; Beregova, Tetyana V; Bodnar, Petro M; Zholobak, Nadiya M; Shcherbakov, Oleksandr B; Bubnov, Rostyslav V; Spivak, Mykola Ya

    2015-01-01

    Male infertility has largely idiopathic, multifactorial origin. Oxidative stress is a major factor that affects spermatogenesis, in particular in aging. Cerium dioxide nanoparticles (CNPs) due to their antioxidative properties are promising to impact on the development of male infertility. The aims of this study were to investigate the effects of CNPs on fertility parameters in 24-month male rats and to overview relevant literature in the field of personalized treatments, predictive diagnosis, and preventive measures for male health and fertility. We included 30 24-month-old male rats. After a week of adaptation to the standard diet, the rats were randomly divided into three groups with ten rats in each. Group 1 (controls) received only a standard diet. The rats of group 2 and 3 in adjunct to the standard diet during 10 days received intragastrically 10 % sodium citrate and citrate-coated CNPs in dose 1 mg/kg, respectively. We assessed sex hormones, epididymal sperm parameters and spermatogenesis, ultrasound, and morphological data of rat reproductive organs. After a 10-day administration of CNPs, we revealed significant decrease of lipid peroxidation product levels in serum and increase of catalase and SOD activity, associated with increase of sperm count (p < 0.001) and improvement in quantitative sperm parameters (motility, viability, and percentage of spermatozoa). We found no significant changes between sperm quantitative parameters in citrate-treated rats and controls and observed age-related decrease of activated Leydig cell number and focal atrophy of the seminiferous tubules. In CNP group, we observed regeneration of seminiferous tubules, increase number and activation of Leydig cells, and 2.5-fold significant increase of serum testosterone. Ultrasound data showed the slight increase of linear measurement and volume of rat testes in CNP group. Review highlights the benefits for predictive diagnosis, preventive measures, and personalized approaches to

  3. The Preparation and Characterization of Mesoporous Cerium Dioxide and Its Properties in the Oxidation of CO%介孔二氧化铈的制备、表征以及对CO的氧化性能研究

    Institute of Scientific and Technical Information of China (English)

    田俊杰; 纳薇; 王华; 高文桂; 刘自松; 郭伟

    2013-01-01

    以无机盐硝酸铈和柠檬酸为原料,CTAB(十六烷基三甲基溴化铵)为模板剂,采用水热法制备了大比表面积的介孔CeO2,结合X射线粉末衍射(XRD)、N2吸附与脱附、H2程序升温还原(H2-TPR)和CO2程序升温脱附(CO2-TPD)等表征手段研究了CTAB加入及焙烧温度对介孔CeO2晶型结构和比表面积的影响,并对CO氧化催化机理进行了初步探讨.结果表明:前驱体与焙烧样品都具有晶型较好的CeO2立方萤石晶相结构和较大的比表面积,CTAB的加入不仅增大了样品的比表面积和孔容,而且在一定程度上提高了样品的结晶度;与其他样品相比,加入CTAB焙烧后的样品具有较好的催化效果.%High surface area mesoporous CeO2 was synthesized using inorganic salt nitric acid cerium and citric acid as raw materials and CTAB (hexadecyl trimethyl ammonium bromide) as template via hydrothermal method. The X-ray powder diffraction (XRD), N2 adsorption and desorption, H2 temperature programmed reduction(H2-TPR) and CO2 temperature programmed desorption(CO2-TPD) were used to study the crystal structure and surface area as well as the mechanism of CO oxidation of the obtained mesoporous CeO2 samples. The results show that all of the samples have pure CeO2 cubic fluorite crystalline structure and a high surface area. The addition of CTAB has not only improved surface area and pore volume of the products, but also enhanced the crystallinity of obtained CeO2. The sample which in the presence of CTAB exhibits a more excellent catalytic activity for CO oxidation rather than the other samples.

  4. Electrorheological Effects of Cerium-Doped TiO2

    Institute of Scientific and Technical Information of China (English)

    尹剑波; 赵晓鹏

    2001-01-01

    It is found that the doping of cerium ion into anatase TiO2 can improve the electrorheological (ER) effects of TiO2 and broaden the operational temperature range. Especially, the substitution of 7-11 mol% of the cerium dopant for Ti can obtain a relatively high shear stress, t-7.4kPa (at 4kV/mm), which is ten times larger than that of pure TiO2 ER fluid. Also, the typical Ce-doped TiO2 ER fluid shows the highest shear stress at 80℃, but 40℃ for pure TiO2 ER fluid. The dielectric loss and dielectric constant at a low frequency of TiO2 is improved by the doping of cerium, and the temperature dependence of the dielectric properties shows an obvious differnce between pure and doped TiO2 ER fluids. These can well explain the ER behaviour of doped TiO2. Furthermore, the change of rheological and dielectric properties is discussed on the basis of the lattice distortion and defects in TiO2 arising from the doping of cerium.

  5. The system-wide economics of a carbon dioxide capture, utilization, and storage network: Texas Gulf Coast with pure CO2-EOR flood

    Science.gov (United States)

    King, Carey W.; Gülen, Gürcan; Cohen, Stuart M.; Nuñez-Lopez, Vanessa

    2013-09-01

    This letter compares several bounding cases for understanding the economic viability of capturing large quantities of anthropogenic CO2 from coal-fired power generators within the Electric Reliability Council of Texas electric grid and using it for pure CO2 enhanced oil recovery (EOR) in the onshore coastal region of Texas along the Gulf of Mexico. All captured CO2 in excess of that needed for EOR is sequestered in saline formations at the same geographic locations as the oil reservoirs but at a different depth. We analyze the extraction of oil from the same set of ten reservoirs within 20- and five-year time frames to describe how the scale of the carbon dioxide capture, utilization, and storage (CCUS) network changes to meet the rate of CO2 demand for oil recovery. Our analysis shows that there is a negative system-wide net present value (NPV) for all modeled scenarios. The system comes close to breakeven economics when capturing CO2 from three coal-fired power plants to produce oil via CO2-EOR over 20 years and assuming no CO2 emissions penalty. The NPV drops when we consider a larger network to produce oil more quickly (21 coal-fired generators with CO2 capture to produce 80% of the oil within five years). Upon applying a CO2 emissions penalty of 602009/tCO2 to fossil fuel emissions to ensure that coal-fired power plants with CO2 capture remain in baseload operation, the system economics drop significantly. We show near profitability for the cash flow of the EOR operations only; however, this situation requires relatively cheap electricity prices during operation.

  6. Preparation of Nano-TiO2 Doped with Cerium and Its Photocatalytic Activity

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Cerium-doped titanium dioxide nano-powders were prepared through the sol-gel method and the compound samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV/Vis diffuse reflectance spectra (DRS). The photocatalytic activity was evaluated by photocatalytic degradation of phenol in water. The results of XRD, TEM, and DRS show that pure TiO2 and Ce-doped TiO2 powder crystallines are a mixture of anatase and rutile;the doping can retard the development of the grain size of TiO2 and decrease the diameter of TiO2 from more than 20nm of pure TiO2 to about 10 nm;the doped TiO2 can improve the light absorption of TiO2 and suitable doping content tends to move the DRS spectrum of TiO2 towards visible light, but too much doping is not good for the light absorption ability.The results of the photocatalytic experiments show that doping with Ce content of 0.08 % ~ 0.4 % can increase the photocatalytic activity of TiO2;however, doping with Ce content of 0.5 % ~ 2.5 % can significantly decrease the photocatalytic activity of TiO2. The favorite doping content is 0.4 % in the range of our experiments.

  7. Fabrication of Cerium Oxide and Uranium Oxide Microspheres for Space Nuclear Power Applications

    Energy Technology Data Exchange (ETDEWEB)

    Jeffrey A. Katalenich; Michael R. Hartman; Robert C. O' Brien

    2013-02-01

    Cerium oxide and uranium oxide microspheres are being produced via an internal gelation sol-gel method to investigate alternative fabrication routes for space nuclear fuels. Depleted uranium and non-radioactive cerium are being utilized as surrogates for plutonium-238 (Pu-238) used in radioisotope thermoelectric generators and for enriched uranium required by nuclear thermal rockets. While current methods used to produce Pu-238 fuels at Los Alamos National Laboratory (LANL) involve the generation of fine powders that pose a respiratory hazard and have a propensity to contaminate glove boxes, the sol-gel route allows for the generation of oxide microsphere fuels through an aqueous route. The sol-gel method does not generate fine powders and may require fewer processing steps than the LANL method with less operator handling. High-quality cerium dioxide microspheres have been fabricated in the desired size range and equipment is being prepared to establish a uranium dioxide microsphere production capability.

  8. Mechanochemical synthesis of cerium orthophosphate

    Institute of Scientific and Technical Information of China (English)

    A.Matraszek; I.Szczygiei; L.Macalik; J.Hanuza

    2009-01-01

    A facile,simple and rapid preparation method of cerium orthophosphate was presented.The synthesis of low-crystalline CePO4 occurred upon mixing of cerium (Ⅲ) nitrate and sodium phosphate,and was an exchange-type reaction.The phase composition of the obtained powder was checked by the XRD and FTIR methods,indicating the presence of cerium phosphate.Further investigations on thermal behavior of the synthesized cerium salt had shown that the obtained onhophosphate crystallized at first in rhabdophane-type structure.It convetted to monazite (monoclinic symmetry) during heating at the temperatures of above 600 ℃.Oxidation of Ce3+ to Ce4+ was avoided during the syntheses,as confirmed by the XPS experiments.

  9. Cerium (IV) oxide nanotubes prepared by low temperature deposition at normal pressure

    Energy Technology Data Exchange (ETDEWEB)

    Boehme, M; Fu, G; Ionescu, E; Ensinger, W, E-mail: mboehme@ca.tu-darmstadt.de [Department of Materials Science, Darmstadt University of Technology, D-64287 Darmstadt (Germany)

    2011-02-11

    This paper reports the synthesis of cerium dioxide nanotubes (CeNTs) by electroless deposition using ion-track-etched polycarbonate templates. To achieve nanotubes with thin walls and small surface roughness the tubes were generated by a several-step-containing procedure under aqueous conditions. The approach reported below will process open end nanotubes with well-defined outer diameter and wall thickness.

  10. Cerium (IV) oxide nanotubes prepared by low temperature deposition at normal pressure.

    Science.gov (United States)

    Boehme, M; Fu, G; Ionescu, E; Ensinger, W

    2011-02-11

    This paper reports the synthesis of cerium dioxide nanotubes (CeNTs) by electroless deposition using ion-track-etched polycarbonate templates. To achieve nanotubes with thin walls and small surface roughness the tubes were generated by a several-step-containing procedure under aqueous conditions. The approach reported below will process open end nanotubes with well-defined outer diameter and wall thickness.

  11. Environmental geochemistry of cerium: applications and toxicology of cerium oxide nanoparticles.

    Science.gov (United States)

    Dahle, Jessica T; Arai, Yuji

    2015-01-23

    Cerium is the most abundant of rare-earth metals found in the Earth's crust. Several Ce-carbonate, -phosphate, -silicate, and -(hydr)oxide minerals have been historically mined and processed for pharmaceutical uses and industrial applications. Of all Ce minerals, cerium dioxide has received much attention in the global nanotechnology market due to their useful applications for catalysts, fuel cells, and fuel additives. A recent mass flow modeling study predicted that a major source of CeO2 nanoparticles from industrial processing plants (e.g., electronics and optics manufactures) is likely to reach the terrestrial environment such as landfills and soils. The environmental fate of CeO2 nanoparticles is highly dependent on its physcochemical properties in low temperature geochemical environment. Though there are needs in improving the analytical method in detecting/quantifying CeO2 nanoparticles in different environmental media, it is clear that aquatic and terrestrial organisms have been exposed to CeO2 NPs, potentially yielding in negative impact on human and ecosystem health. Interestingly, there has been contradicting reports about the toxicological effects of CeO2 nanoparticles, acting as either an antioxidant or reactive oxygen species production-inducing agent). This poses a challenge in future regulations for the CeO2 nanoparticle application and the risk assessment in the environment.

  12. Environmental Geochemistry of Cerium: Applications and Toxicology of Cerium Oxide Nanoparticles

    Directory of Open Access Journals (Sweden)

    Jessica T. Dahle

    2015-01-01

    Full Text Available Cerium is the most abundant of rare-earth metals found in the Earth’s crust. Several Ce-carbonate, -phosphate, -silicate, and -(hydroxide minerals have been historically mined and processed for pharmaceutical uses and industrial applications. Of all Ce minerals, cerium dioxide has received much attention in the global nanotechnology market due to their useful applications for catalysts, fuel cells, and fuel additives. A recent mass flow modeling study predicted that a major source of CeO2 nanoparticles from industrial processing plants (e.g., electronics and optics manufactures is likely to reach the terrestrial environment such as landfills and soils. The environmental fate of CeO2 nanoparticles is highly dependent on its physcochemical properties in low temperature geochemical environment. Though there are needs in improving the analytical method in detecting/quantifying CeO2 nanoparticles in different environmental media, it is clear that aquatic and terrestrial organisms have been exposed to CeO2 NPs, potentially yielding in negative impact on human and ecosystem health. Interestingly, there has been contradicting reports about the toxicological effects of CeO2 nanoparticles, acting as either an antioxidant or reactive oxygen species production-inducing agent. This poses a challenge in future regulations for the CeO2 nanoparticle application and the risk assessment in the environment.

  13. PLUTONIUM-CERIUM-COBALT AND PLUTONIUM-CERIUM-NICKEL ALLOYS

    Science.gov (United States)

    Coffinberry, A.S.

    1959-08-25

    >New plutonium-base teroary alloys useful as liquid reactor fuels are described. The alloys consist of 10 to 20 atomic percent cobalt with the remainder plutonium and cerium in any desired proportion, with the plutonium not in excess of 88 atomic percent; or, of from 10 to 25 atomic percent nickel (or mixture of nickel and cobalt) with the remainder plutonium and cerium in any desired proportion, with the plutonium not in excess of 86 atomic percent. The stated advantages of these alloys over unalloyed plutonium for reactor fuel use are a lower melting point and a wide range of permissible plutonium dilution.

  14. Application of preparation process of high pure chlorine dioxide by electrolysis method in water treatment%电解法制高纯二氧化氯工艺在水处理中的应用

    Institute of Scientific and Technical Information of China (English)

    刘艳霞; 韩瑞雄; 赵红; 周俊波

    2011-01-01

    为了开发经济实用的二氧化氯消毒工艺,对电解法制备高纯二氧化氯工艺在水处理中的运用进行了研究.在最佳条件下,电解氯酸盐自动催化循环制备的二氧化氯纯度可达98%左右.通过二氧化氯杀菌除藻试验,讨论了二氧化氯用量以及原水pH对细菌、叶绿素a、藻类的去除率的影响.结果表明,二氧化氯用量在2 mg/L以上时,3者的去除率均达到90%以上.当二氧化氯用量为2 mg/L、原水pH为6~9时,3者的去除率不发生显著变化,并且二氧化氯的剩余质量浓度均控制在0.5 mg/L以下.消毒成本:生产1 kg二氧化氯成本可以控制在6元以内,当二氧化氯用量在0.5 ~2 mg/L时,1 t水的消毒成本为0.003~ 0.012元.%To develop an economical and practical disinfection technology of chlorine dioxide, the application of preparation process of high pure chlorine dioxide by electrolysis method in water treatment was studied. Under the best conditions, the purity of chlorine dioxide, which was prepared by electrolysis of chlorate solution with auto-catalytic cycling,can reach about 98% . Through the experiments of algae removal and sterilization,the influences of concentration of chlorine dioxide and pH of raw water on the removal rate of bacteria,chlorophyll A ,and algal were discussed. Results showed that when the mass concentration of chlorine dioxide was above 2 mg/L, the removal rates of bacteria, chlorophyll A, and algal could all reached above 90% . When the mass concentration of chlorine dioxide was 2 mg/L and pH of raw water was at 6 ~9,the removal rates of them could not occur significant change, and the mass concentration of residual chlorine dioxide was all under 0. 5 mg/L. Though accounting for the cost of water disinfection, the cost of per kilogram chlorine dioxide in the process can be controlled less than RMB 6 Yuan. When the invested amount of chlorine dioxide was at 0.5 ~2 mg/L,and the cost of per ton water disinfection

  15. Preparation and visible-light-driven photocatalytic performance of cerium-doped titanium dioxide%Ce掺杂TiO2的制备及其可见光光催化性能

    Institute of Scientific and Technical Information of China (English)

    富好; 罗秀针; 袁霞; 施俊新; 高碧芬

    2013-01-01

    Ce-doped TiO2 nanoparticles were prepared by sol-gel method.The structure and physicochemical properties of the catalysts were investigated by means of XRD,FT-IR,XPS,UV-Vis DRS,etc.The photocat-alytic activities of Ce-doped TiO2 were evaluated by the degradation of acid red under visible light irradiation. The experiment results show that Ce-O-Ti bonds are formed on the interface of cerium oxide and TiO2 ,so that the crystallization and phase transition processes of the catalyst are impeded.Ce-TiO2 has a significant ab-sorption in the visible region and the recombination of the photo-generated electron and hole pairs was greatly inhibited.Hence,the visible-light-driven photocatalytic efficiency of Ce-TiO2 was significantly enhanced.The catalyst doped with 20% Ce presents the best activity when calcinated at 400 ℃.%采用溶胶-凝胶法制备 Ce 掺杂 TiO2(Ce-TiO2)纳米颗粒,借助 XRD、XPS、UV-Vis、DRS 等手段对催化剂的结构和理化性质进行分析表征,并以酸性红染料作为模型污染物,考察 Ce-TiO2在可见光作用下的催化活性。实验结果表明,在 CeO2和 TiO2界面形成了Ce-O-Ti键,从而抑制了催化剂的晶化和相转变过程,并在 TiO2的禁带中引入了 Ce4f 掺杂能级。Ce-TiO2在可见光区具有显著吸收,且光生载流子的复合受到有效抑制,因此,Ce 掺杂明显提高了TiO2降解污染物的效率。当 Ce 掺杂量为20%(摩尔分数),煅烧温度为400℃时,催化剂的活性达到最佳。

  16. Catalytic conversion of carbon dioxide into dimethyl carbonate using reduced copper-cerium oxide catalysts as low as 353 K and 1.3 MPa and the reaction mechanism

    Directory of Open Access Journals (Sweden)

    Seiki eWada

    2013-06-01

    Full Text Available Synthesis of dimethyl carbonate (DMC from CO2 and methanol under milder reaction conditions was performed using reduced cerium oxide catalysts and reduced copper-promoted Ce oxide catalysts. Although the conversion of methanol was low (0.005–0.11% for 2 h of reaction, DMC was synthesized as low as 353 K and at total pressure of as low as 1.3 MPa using reduced Cu–CeO2 catalyst (0.5 wt% of Cu. The apparent activation energy was 120 kJ mol–1 and the DMC synthesis rates were proportional to the partial pressure of CO2. An optimum amount of Cu addition to CeO2 was 0.1 wt% for DMC synthesis under the conditions at 393 K and total pressure of 1.3 MPa for 2 h (conversion of methanol: 0.15% due to the compromise of two effects of Cu: the activation of H2 during reduction prior to the kinetic tests and the block (cover of the surface active site. The reduction effects in H2 were monitored through the reduction of Ce4+ sites to Ce3+ based on the shoulder peak intensity at 5727 eV in the Ce L3-edge X-ray absorption near-edge structure (XANES. The Ce3+ content was 10% for reduced CeO2 catalyst whereas it increased to 15% for reduced Cu–CeO2 catalyst (0.5wt% of Cu. Moreover, the content of reduced Ce3+ sites (10% associated with the surface O vacancy (defect sites decreased to 5% under CO2 at 290 K for reduced Cu–CeO2 catalyst (0.1wt% of Cu. The adsorption step of CO2 on the defect sites might be the key step in DMC synthesis and thus the DMC synthesis rate dependence on the partial pressure of CO2 was proportional. Subsequent H atom subtraction steps from methanol at the neighboring surface Lewis base sites should combine two methoxy species to the adsorbed CO2 to form DMC, water, and restore the surface O vacancy.

  17. Photocatalytic action of cerium molybdate and iron-titanium oxide hollow nanospheres on Escherichia coli

    Energy Technology Data Exchange (ETDEWEB)

    Kartsonakis, I. A., E-mail: ikartsonakis@ims.demokritos.gr; Kontogiani, P.; Pappas, G. S.; Kordas, G. [NCSR ' DEMOKRITOS' , Sol-Gel Laboratory, Institute of Advanced Materials, Physicochemical Processes, Nanotechnology and Microsystems (Greece)

    2013-06-15

    This study is focused on the production of hollow nanospheres that reveal antibacterial action. Cerium molybdate and iron-titanium oxide hollow nanospheres with a diameter of 175 {+-} 15 and 221 {+-} 10 nm, respectively, were synthesized using emulsion polymerization and the sol-gel process. Their morphology characterization was accomplished using scanning electron microscopy. Their antibacterial action was examined on pure culture of Escherichia coli considering the loss of their viability. Both hollow nanospheres presented photocatalytic action after illumination with blue-black light, but those of cerium molybdate also demonstrated photocatalytic action in the dark. Therefore, the produced nanospheres can be used for antibacterial applications.

  18. Photocatalytic action of cerium molybdate and iron-titanium oxide hollow nanospheres on Escherichia coli

    Science.gov (United States)

    Kartsonakis, I. A.; Kontogiani, P.; Pappas, G. S.; Kordas, G.

    2013-06-01

    This study is focused on the production of hollow nanospheres that reveal antibacterial action. Cerium molybdate and iron-titanium oxide hollow nanospheres with a diameter of 175 ± 15 and 221 ± 10 nm, respectively, were synthesized using emulsion polymerization and the sol-gel process. Their morphology characterization was accomplished using scanning electron microscopy. Their antibacterial action was examined on pure culture of Escherichia coli considering the loss of their viability. Both hollow nanospheres presented photocatalytic action after illumination with blue-black light, but those of cerium molybdate also demonstrated photocatalytic action in the dark. Therefore, the produced nanospheres can be used for antibacterial applications.

  19. A chemical-spectrochemical method for the determination of rare earth elements and thorium in cerium minerals

    Science.gov (United States)

    Rose, H.J.; Murata, K.J.; Carron, M.K.

    1954-01-01

    In a combined chemical-spectrochemical procedure for quantitatively determining rare earth elements in cerium minerals, cerium is determined volumetrically, a total rare earths plus thoria precipitate is separated chemically, the ceria content of the precipitate is raised to 80??0 percent by adding pure ceria, and the resulting mixture is analyzed for lanthanum, praseodymium, neodymium, samarium, gadolinium, yttrium, and thorium spectrochemically by means of the d.c. carbon arc. Spectral lines of singly ionized cerium are used as internal standard lines in the spectrochemical determination which is patterned after Fassel's procedure [1]. Results of testing the method with synthetic mixtures of rare earths and with samples of chemically analyzed cerium minerals show that the coefficient of variation for a quadruplicate determination of any element does not exceed 5??0 (excepting yttrium at concentrations less than 1 percent) and that the method is free of serious systematic error. ?? 1954.

  20. Implantation of silicon dioxide-based nanocrystalline hydroxyapatite and pure phase beta-tricalciumphosphate bone substitute granules in caprine muscle tissue does not induce new bone formation

    Directory of Open Access Journals (Sweden)

    Ghanaati Shahram

    2013-01-01

    Full Text Available Abstract Background Osteoinductive bone substitutes are defined by their ability to induce new bone formation even at heterotopic implantation sites. The present study was designed to analyze the potential osteoinductivity of two different bone substitute materials in caprine muscle tissue. Materials and methods One gram each of either a porous beta-tricalcium phosphate (β-TCP or an hydroxyapatite/silicon dioxide (HA/SiO2-based nanocrystalline bone substitute material was implanted in several muscle pouches of goats. The biomaterials were explanted at 29, 91 and 181 days after implantation. Conventional histology and special histochemical stains were performed to detect osteoblast precursor cells as well as mineralized and unmineralized bone matrix. Results Both materials underwent cellular degradation in which tartrate-resistant acid phosphatase (TRAP-positive osteoclast-like cells and TRAP-negative multinucleated giant cells were involved. The ß-TCP was completely resorbed within the observation period, whereas some granules of the HA-groups were still detectable after 180 days. Neither osteoblasts, osteoblast precursor cells nor extracellular bone matrix were found within the implantation bed of any of the analyzed biomaterials at any of the observed time points. Conclusions This study showed that ß-TCP underwent a faster degradation than the HA-based material. The lack of osteoinductivity for both materials might be due to their granular shape, as osteoinductivity in goat muscle has been mainly attributed to cylindrical or disc-shaped bone substitute materials. This hypothesis however requires further investigation to systematically analyze various materials with comparable characteristics in the same experimental setting.

  1. Dissolution properties of cerium dibutylphosphate corrosion inhibitors

    NARCIS (Netherlands)

    Soestbergen, M. van; Erich, S.J.F.; Huinink, H.P.; Adan, O.C.G.

    2013-01-01

    The corrosion inhibitor cerium dibutylphosphate, Ce(dbp)3, prevents corrosion by cerium and dbp deposition at the alkaline cathode and acidic anode respectively. The pH dependent Ce(dbp)3 solubility seems to play an essential role in the inhibition degree. We found that Ce(dbp) 3 scarcely dissolves

  2. Formulation and method for preparing gels comprising hydrous cerium oxide

    Science.gov (United States)

    Collins, Jack L; Chi, Anthony

    2013-05-07

    Formulations useful for preparing hydrous cerium oxide gels contain a metal salt including cerium, an organic base, and a complexing agent. Methods for preparing gels containing hydrous cerium oxide include heating a formulation to a temperature sufficient to induce gel formation, where the formulation contains a metal salt including cerium, an organic base, and a complexing agent.

  3. Characterization of cerium fluoride nanocomposite scintillators

    Energy Technology Data Exchange (ETDEWEB)

    Stange, Sy [Los Alamos National Laboratory; Esch, Ernst I [Los Alamos National Laboratory; Brown, Leif O [Los Alamos National Laboratory; Couture, Aaron J [Los Alamos National Laboratory; Mckigney, Edward A [Los Alamos National Laboratory; Muenchausen, Ross E [Los Alamos National Laboratory; Del Sesto, Rico E [Los Alamos National Laboratory; Gilbertson, Robert D [Los Alamos National Laboratory; Mccleskey, T Mark [Los Alamos National Laboratory; Reifarth, Rene [Los Alamos National Laboratory

    2009-01-01

    Measurement of the neutron capture cross-sections of a number of short-lived isotopes would advance both pure and applied scientific research. These cross-sections are needed for calculation of criticality and waste production estimates for the Advanced Fuel Cycle Initiative, for analysis of data from nuclear weapons tests, and to improve understanding of nucleosynthesis. However, measurement of these cross-sections would require a detector with a faster signal decay time than those used in existing neutron capture experiments. Crystals of faster detector materials are not available in sufficient sizes and quantities to supply these large-scale experiments. Instead, we propose to use nanocomposite detectors, consisting of nanoscale particles of a scintillating material dispersed in a matrix material. We have successfully fabricated cerium fluoride (CeF{sub 3}) nanoparticles and dispersed them in a liquid matrix. We have characterized this scintillator and have measured its response to neutron capture. Results of the optical, structural, and radiation characterization will be presented.

  4. A cerium(IV)-carbon multiple bond

    Energy Technology Data Exchange (ETDEWEB)

    Gregson, Matthew; Lu, Erli; McMaster, Jonathan; Lewis, William; Blake, Alexander J.; Liddle, Stephen T. [Nottingham Univ. (United Kingdom). School of Chemistry

    2013-12-02

    Straightforward access to a cerium(IV)-carbene complex was provided by one-electron oxidation of an anionic ''ate'' cerium(III)-carbene precursor, thereby avoiding decomposition reactions that plague oxidations of neutral cerium(III) compounds. The cerium(IV)-carbene complex is the first lanthanide(IV)-element multiple bond and involves a twofold bonding interaction of two electron pairs between cerium and carbon. [German] Auf direktem Wege zu einem Cer(IV)-Carbenkomplex gelangt man durch die Einelektronenoxidation einer anionischen Carben-Cerat(III)-Vorstufe. So werden Zersetzungsprozesse vermieden, die die Oxidation neutraler Cer(III)-Verbindungen erschweren. Der Cer(IV)-Carbenkomplex enthaelt die erste Lanthanoid(IV)-Element-Mehrfachbindung; dabei binden Cer und Kohlenstoff ueber zwei Elektronenpaare.

  5. Anti-erosive potential of amine fluoride, cerium chloride and laser irradiation application on dentine.

    Science.gov (United States)

    Wegehaupt, Florian J; Sener, Beatrice; Attin, Thomas; Schmidlin, Patrick R

    2011-12-01

    Ninety-six dentine samples were prepared from human premolars and randomly assigned to eight groups (G1-G8). Samples were treated for 30s with the following solutions: placebo (G1/G2), amine fluoride (Elmex fluid; G3/G4), cerium chloride (G5/G6) and combined fluoride/cerium chloride application (G7/G8). Samples of groups G2, G4, G6 and G8 were additionally irradiated with a carbon dioxide laser through the solutions for 30s. Acid resistance was assessed in a six-time 5-min consecutive lactic acid (pH 3.0) erosion model and calcium release was determined by atomic absorption spectroscopy (AAS). Furthermore, six additional samples per group were prepared and subjected to EDS-analysis. In the non-irradiated groups, specimens of G1 (placebo) showed the highest calcium release when compared to the other treatments (G3, G5 and G7). The highest acid resistance was observed for G7. In G3, calcium release was lower than in G5, but higher than in G7. In general (except for the placebo groups), calcium release in the laser-irradiated groups was higher compared with the respective non-irradiated groups. EDS showed a replacement of calcium by cerium and of phosphor by fluoride. The highest anti-erosive potential was found after combined cerium chloride and amine fluoride application. Laser irradiation had not adjunctive effect. Copyright © 2011 Elsevier Ltd. All rights reserved.

  6. Cerium extraction by metallothermic reduction using cerium oxide powder injection

    Institute of Scientific and Technical Information of China (English)

    J.S. Luna A; A. Flores V; R. Mu(n)iz V; A.F. Fuentes; J. Torres; N. Rodríuez R; J.C. Ortiz; P.Orozco

    2011-01-01

    This work presented the feasibility of cerium recovery by Al-Mg alloy through the metallothermic reduction of CeO2 to obtain a master alloy Al-4%Ce. The master alloy obtained in this investigation was for the grain refinement and modification of Al-Si alloys. The reagent was incorporated into a molten alloy using the submerged powder injection technique, and metallic samples were obtained during injection. Chemical and microstructural analyses (by inductively coupled plasma (ICP) and scanning electron microscopy (SEM), respectively) confirmed the possibility of Ce uptake in the bath (0 to 4 wt.%), as CeO2 was reduced through metallothermic reactions in the molten alloys.Based on the characterization of reaction products, the sequence of the reaction was proposed.

  7. Some Environmentally Relevant Reactions of Cerium Oxide

    Directory of Open Access Journals (Sweden)

    Janoš Pavel

    2014-12-01

    Full Text Available Reactive forms of cerium oxide were prepared by a thermal decomposition of various precursors, namely carbonates, oxalates and citrates, commercially available nanocrystalline cerium oxide (nanoceria was involved in the study for comparison. Scanning electron microscopy (SEM and x-ray diffraction analysis (XRD were used to examine the morphology and crystallinity of the samples, respectively, whereas the Brunauer-Emmett-Teller (BET method of nitrogen adsorption was used to determine surface areas. Interactions of cerium oxide with some phosphorus-containing compounds were investigated. Some of the examined samples, especially those prepared by annealing from carbonate precursors, exhibited an outstanding ability to destroy highly toxic organophosphates, such as pesticides (parathion methyl, or nerve agents (soman, VX. There were identified some relations between the degradation efficiency of cerium oxides and their crystallinity. It was also shown that cerium oxide is able to destroy one of widely used flame retardants - triphenyl phosphate. A phosphatase-mimetic activity of various cerium oxides was examined with the aid of a standardized phosphatase test.

  8. Pharmacological potential of cerium oxidenanoparticles

    Science.gov (United States)

    Celardo, Ivana; Pedersen, Jens Z.; Traversa, Enrico; Ghibelli, Lina

    2011-04-01

    Nanotechnology promises a revolution in pharmacology to improve or create ex novo therapies. Cerium oxidenanoparticles (nanoceria), well-known as catalysts, possess an astonishing pharmacological potential due to their antioxidant properties, deriving from a fraction of Ce3+ ions present in CeO2. These defects, compensated by oxygen vacancies, are enriched at the surface and therefore in nanosized particles. Reactions involving redox cycles between the Ce3+ and Ce4+oxidation states allow nanoceria to react catalytically with superoxide and hydrogen peroxide, mimicking the behavior of two key antioxidant enzymes, superoxide dismutase and catalase, potentially abating all noxious intracellularreactive oxygen species (ROS) via a self-regenerating mechanism. Hence nanoceria, apparently well tolerated by the organism, might fight chronic inflammation and the pathologies associated with oxidative stress, which include cancer and neurodegeneration. Here we review the biological effects of nanoceria as they emerge from in vitro and in vivo studies, considering biocompatibility and the peculiar antioxidant mechanisms.

  9. Growth and characterization of Sm3+ doped cerium oxalate single crystals

    Directory of Open Access Journals (Sweden)

    Minu Mary C

    2016-07-01

    Full Text Available Single crystals of Sm3+ doped cerium oxalate decahydrate were synthesized using single diffusion gel technique and the conditions influencing the size, morphology, nucleation density and quality of the crystals were optimized. Highly transparent single crystals of average size 3 mm × 2 mm × 1 mm with well-defined hexagonal morphology were grown during a time period of two weeks. X-ray powder diffraction analysis revealed that the grown crystals crystallize in the monoclinic system with space group P21/c as identical with the pure cerium oxalate. The various functional groups of the oxalate ligand and the water of crystallization were identified by Fourier transform infrared spectroscopy. The photoluminescence spectrum of the Sm3+ doped cerium oxalate indicated that the Sm3+ ions are optically active in the cerium oxalate matrix. The crystal has a strong and efficient orange red emission with a wavelength peak at 595 nm and hence can be effectively used for optical amplification. Microhardness measurements of the crystal revealed that they belong to the soft material category.

  10. Room-temperature ferromagnetism in cerium dioxide powders

    Energy Technology Data Exchange (ETDEWEB)

    Rakhmatullin, R. M., E-mail: rrakhmat@kpfu.ru; Pavlov, V. V.; Semashko, V. V.; Korableva, S. L. [Kazan Federal University, Institute of Physics (Russian Federation)

    2015-08-15

    Room-temperature ferromagnetism is detected in a CeO{sub 2} powder with a grain size of about 35 nm and a low (<0.1 at %) manganese and iron content. The ferromagnetism in a CeO{sub 2} sample with a submicron crystallite size and the same manganese and iron impurity content is lower than in the nanocrystalline sample by an order of magnitude. Apart from ferromagnetism, both samples exhibit EPR spectra of localized paramagnetic centers, the concentration of which is lower than 0.01 at %. A comparative analysis of these results shows that the F-center exchange (FCE) mechanism cannot cause ferromagnetism. This conclusion agrees with the charge-transfer ferromagnetism model proposed recently.

  11. Cyanex 923 as the extractant in a rare earth element impurity analysis of high-purity cerium oxide.

    Science.gov (United States)

    Duan, Taicheng; Li, Hongfei; Kang, JianZhen; Chen, Hangting

    2004-06-01

    In this work, the feasibility of employing Cyanex 923 as an extractant into the non-cerium REE (rare earth elements) impurity analysis of high-purity cerium oxide was investigated. Through investigations on the choice of the extraction medium, the optimium extraction acidity, matrix Ce4+ effect on the non-cerium REE ion extraction, the optimium extractant concentration and suitable extracting time, and oscillation strengh, it was found that when the phase ratio was at 1:1 and the acicidity was about 2% H2SO4, by gently shaking by hand for about 2 min, 10 mL of 30% Cyanex 923 could not extract even for a 20 ng amount of non-cerium REE3+ ions. However, the extraction efficiency for Ce4+ of 100 mg total amount under the same conditions was about 96%, indicating that a 25-fold preconcentration factor could be achieved. Thus, it was concluded that Cyanex 923 could be used in a REE impurity analysis of 99.9999% or so pure cerium oxide for primary sepapation to elimilate matrix-induced interferences encountered in an ICP-MS (inductively coupled plasma mass spectroscopy) determination.

  12. Nanocrystalline cerium oxide materials for solid fuel cell systems

    Science.gov (United States)

    Brinkman, Kyle S

    2015-05-05

    Disclosed are solid fuel cells, including solid oxide fuel cells and PEM fuel cells that include nanocrystalline cerium oxide materials as a component of the fuel cells. A solid oxide fuel cell can include nanocrystalline cerium oxide as a cathode component and microcrystalline cerium oxide as an electrolyte component, which can prevent mechanical failure and interdiffusion common in other fuel cells. A solid oxide fuel cell can also include nanocrystalline cerium oxide in the anode. A PEM fuel cell can include cerium oxide as a catalyst support in the cathode and optionally also in the anode.

  13. Analysis of single and binary phases in cerium doped sodium bismuth titanate -inorganic materials Na{sub 0}.5Bi{sub (}0.5-x)Ce{sub x}TiO{sub 3}; Estudio de fases simples y binarias en BNT puro y dopado con cerio Na{sub 0},5Bi{sub (}0,5-x)Ce{sub x}TiO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Supriya, S.; Dos Santos-Garcia, A. J.; Frutos, J. de; Fernandez-Martinez, F.

    2015-07-01

    The pure and cerium doped sodium bismuth titanate (NBT) inorganic powders were synthesized by solid-state reaction method. The presence of rhombohedral phase was observed in cerium doped NBT compounds. When x= 0.05 of cerium doped NBT is heat treated at 1200 degree centigrade, the compound forms single perovskite phase. The samples of x = 0.10 and 0.15 were heat treated up to 1350 degree centigrade, the binary phases with cerium and bismuth oxides were observed. The X-ray diffraction, Fourier transform infrared spectroscopy, reflectance spectra, differential thermal analysis and thermogravimetric analysis were used to analyze the various properties of samples. Moreover, the effects of cerium doping and calcining temperature on NBT samples were investigated. In this work, we present our recent results on the synthesis and characterization of cerium doped sodium bismuth titanate materials. (Author)

  14. CHEMICAL BEHAVIOR OF CERIUM ELEMENT IN ROCK WEATHERING SYSTEM

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    A study on existing valence state and chemical behavior of cerium element in two categories of rock weathering system in China has been carried out. In the granitoid weathering crust of Southern China,cerium as tetravalent hydroxide absorbed on clay minerals occupies 62.58 % of total amount of cerium and the cerium partitioning in the phase is 69.58 %. The depositing cerium stops its mobility downward, resulting in rare earth partitioning variation, the light rare earth partitioning is high at upper layer of weathering crust, the heavy rare earth partitioning is high at bottom layer of weathering crust, and the extracted product exists cerium lose effect. For Mn2+ as reducing agent existing in black weathering earth of Maoniuping rare earth ore,cerium is trivalent and absorbed on Mn-Fe oxide as colloid phase sediment. Colloid sediment phase can be divided into Mn-Fe combined phase and hydroxide sediment phase with cerium contents of 19.77% and 48.30%, and their cerium partitionings are 80.72% and 37.38% respectively. The Mn-Fe combined phase can selectively absorb cerium.

  15. Uptake and accumulation of bulk and nanosized cerium oxide particles and ionic cerium by radish (Raphanus sativus L.).

    Science.gov (United States)

    Zhang, Weilan; Ebbs, Stephen D; Musante, Craig; White, Jason C; Gao, Cunmei; Ma, Xingmao

    2015-01-21

    The potential toxicity and accumulation of engineered nanomaterials (ENMs) in agricultural crops has become an area of great concern and intense investigation. Interestingly, although below-ground vegetables are most likely to accumulate the highest concentrations of ENMs, little work has been done investigating the potential uptake and accumulation of ENMs for this plant group. The overall objective of this study was to evaluate how different forms of cerium (bulk cerium oxide, cerium oxide nanoparticles, and the cerium ion) affected the growth of radish (Raphanus sativus L.) and accumulation of cerium in radish tissues. Ionic cerium (Ce(3+)) had a negative effect on radish growth at 10 mg CeCl3/L, whereas bulk cerium oxide (CeO2) enhanced plant biomass at the same concentration. Treatment with 10 mg/L cerium oxide nanoparticles (CeO2 NPs) had no significant effect on radish growth. Exposure to all forms of cerium resulted in the accumulation of this element in radish tissues, including the edible storage root. However, the accumulation patterns and their effect on plant growth and physiological processes varied with the characteristics of cerium. This study provides a critical frame of reference on the effects of CeO2 NPs versus their bulk and ionic counterparts on radish growth.

  16. Chromium VI adsorption on cerium oxide nanoparticles and morphology changes during the process

    Energy Technology Data Exchange (ETDEWEB)

    Recillas, Sonia; Colon, Joan [Department of Chemical Engineering, Engineering School, Autonomous University of Barcelona, 08193 Bellaterra (Spain); Casals, Eudald; Gonzalez, Edgar [Catalan Institute of Nanotechnology, Autonomous University of Barcelona Campus, 08193 Bellaterra (Spain); Puntes, Victor [Catalan Institute of Nanotechnology, Autonomous University of Barcelona Campus, 08193 Bellaterra (Spain); Catalan Institute of Research and Advanced Studies, Passeig Lluis Companys, 23, 08010 Barcelona (Spain); Sanchez, Antoni, E-mail: antoni.sanchez@uab.cat [Department of Chemical Engineering, Engineering School, Autonomous University of Barcelona, 08193 Bellaterra (Spain); Font, Xavier [Department of Chemical Engineering, Engineering School, Autonomous University of Barcelona, 08193 Bellaterra (Spain)

    2010-12-15

    In this study, suspended cerium oxide nanoparticles stabilized with hexamethylenetetramine were used for the removal of dissolved chromium VI in pure water. Several concentrations of adsorbent and adsorbate were tested, trying to cover a large range of possible real conditions. Results showed that the Freundlich isotherm represented well the adsorption equilibrium reached between nanoparticles and chromium, whereas adsorption kinetics could be modeled by a pseudo-second-order expression. The separation of chromium-cerium nanoparticles from the medium and the desorption of chromium using sodium hydroxide without cerium losses was obtained. Nanoparticles agglomeration and morphological changes during the adsorption-desorption process were observed by TEM. Another remarkable result obtained in this study is the low toxicity in the water treated by nanoparticles measured by the Microtox commercial method. These results can be used to propose this treatment sequence for a clean and simple removal of drinking water or wastewater re-use when a high toxicity heavy metal such as chromium VI is the responsible for water pollution.

  17. Highly stable, mesoporous mixed lanthanum-cerium oxides with tailored structure and reducibility

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Shuang; Broitman, Esteban; Wang, Yanan; Cao, Anmin; Veser, Goetz

    2011-05-01

    Pure and mixed lanthanum and cerium oxides were synthesized via a reverse microemulsion-templated route. This approach yields highly homogeneous and phase-stable mixed oxides with high surface areas across the entire range of La:Ce ratios from pure lanthana to pure ceria. Surprisingly, all mixed oxides show the fluorite crystal structure of ceria, even for lanthanum contents as high as 90%. Varying the La:Ce ratio not only allows tailoring of the oxide morphology (lattice parameter, pore structure, particle size, and surface area), but also results in a fine-tuning of the reducibility of the oxide which can be explained by the creation of oxygen vacancies in the ceria lattice upon La addition. Such finely controlled syntheses, which enable the formation of stable, homogeneous mixed oxides across the entire composition range, open the path towards functional tailoring of oxide materials, such as rational catalyst design via fine-tuning of redox activity.

  18. Synthesis of Cerium-Doped Titania Nanoparticles and Nanotubes.

    Science.gov (United States)

    Cao, Wei; Suzuki, Takuya; Elsayed-Ali, Hani E; Abdel-Fattah, Tarek M

    2015-03-01

    Cerium-doped titania nanoparticles and nanotubes were synthesized via hydrothermal processes. X-Ray Diffraction revealed that cerium-doped titania nanoparticles have an anatase crystal structure, while cerium-doped titania nanotubes have an H2Ti3O7-type structure. Scanning electron microscopy and high resolution transmission electron microscopy showed that both types of titania are well crystallized with relatively uniform size distribution. The photocatalytic degradation of methylthioninium chloride known as methylene blue dye was tested and both cerium-doped titania nanoparticles and nanotubes. The preliminary photocatalytic degradation of Methylene Blue data showed significantly improved visible light photocatalytic activities as compared to commercial titania powders.

  19. AZ91镁合金表面铈盐-硅烷转化膜对比处理研究%Comparison of Surface Treatment of AZ91 Magnesium Alloy with Cerium and Silane Conversion Coatings

    Institute of Scientific and Technical Information of China (English)

    陈言坤; 鲁彦玲; 郭毅; 杜仕国

    2011-01-01

    With different immersion treatment, four kinds of conversion coatings including pure cerium conversion, KH560 silane conversion, cerium - silane conversion and silane - cerium conversion coatings were prepared. The corrosion resistance of four kinds of conversion coatings were studied and compared by use of IR, SEM, EDS, Tafel and EIS. The results showed that there were no interaction between cerium coating and silane coating, and they could form conversion coating independently. The cerium - silane conversion coating and silane - cerium coating showed better corrosion resistance than pure cerium coating and silane coating did. The reason of difference between cerium coating and silane coating needed to be studied further.%利用不同的浸泡处理,制备了单纯铈盐转化膜、KH560硅烷转化膜、铈盐硅烷转化膜和硅烷铈盐4种转化膜,结合FT-IR、SEM、EDS、Tafel、EIS等分析手段,对比考察了4种转化膜对镁合金耐腐蚀能力的情况,结果表明:铈盐转化膜和硅烷转化膜之间没有相互影响,均具有独立成膜的能力;铈盐硅烷转化膜和硅烷铈盐转化膜比单纯的铈盐转化膜和单纯的硅烷转化膜具有更好的耐腐蚀能力;铈盐硅烷转化膜和硅烷铈盐转化膜耐腐蚀能力的差别和原因,尚需要进一步的试验研究.

  20. Cerium and jojoba in engines?; Cerium et jojoba dans les moteurs?

    Energy Technology Data Exchange (ETDEWEB)

    Massy-Delhotel, E.

    1996-10-01

    The Belgium company CreaTel proposes a new system, called Forac, which can lead to a 10% reduction of fuel consumption in thermal engines together with a quasi-complete reduction of CO, HC, NOx pollutants and CO{sub 2} particulates emission. The system comprises a steam production device and an admission pipe with a cerium alloy whorl inside. The steam produced is mixed with the admission air and tears cerium particles from the inside of the admission pipe to the combustion chamber. The cerium particles act as a catalyst which favours the complete combustion of the fuel. The same company proposes also lubricant additives made from liquid jojoba wax which allow the reduction of pollutant emissions, fuel consumption and noise emissions of diesel engines. (J.S.)

  1. Thermodynamics of congruently subliming cerium-antimony

    Energy Technology Data Exchange (ETDEWEB)

    Schiffman, R.A.; Franzen, H.F.

    1982-01-01

    Congruently vaporizing cerium-antimony has been investigated by vapor pressure measurementa using a simultaneous weight-loss mass-spectrometric Knudsen effusion technique. The melting point of the 1:1 stoichiometry was determined to be 2179 +/- 10 K. The heat of formation at 298 K of CeSb was found to be -128.9 kJ/g-at from thermodynamic measurements in the temperature range 1985-2172 K.

  2. Formation and characterization of cerium conversion coatings on magnesium alloy

    Institute of Scientific and Technical Information of China (English)

    LI Lingjie; LEI Jinglei; YU Shenghai; TIAN Yujing; JIANG Qiquan; PAN Fusheng

    2008-01-01

    Chemical conversion treatment by rare earth metal salt solution was considered as an alternative to chromium chemical conversion treatment to improve the corrosion resistance of magnesium alloys. In this study, cerium conversion coatings formed on AZ31 magnesium alloy were characterized and the formation mechanism was discussed. X-ray photoelectron spectroscopy (XPS) analysis showed that cerium conversion coating consisted of cerium hydroxides/oxides, in which both tetravalent cerium Ce(IV) and trivalent cerium Ce(III) species co-existed. Cerium conversion coating was a two-layer structure. Atomic force microscopy (AFM) images revealed that the morphology of the inside layer was different from that of the outside one, which was responsible for the inherent adhesive weakness of the coating. Corrosion potential (Ecorr) measurements indicated that poor adhesion limited the improvement of the corrosion resistance of the coating. During the treating process, the increased pH value of the cerium salt solution led to the precipitation of cerium hydroxides/oxides. The formation kinetics of the coating followed a parabolic curve.

  3. Structural, optical, morphological and dielectric properties of cerium oxide nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Prabaharan, Devadoss Mangalam Durai Manoharadoss [Department of Physics, NPR College of Engineering and Technology, Natham, Dindigul, Tamil Nadu (India); Sadaiyandi, Karuppasamy [Department of Physics, Alagappa Government Arts College, Karaikudi, Sivaganga, Tamil Nadu (India); Mahendran, Manickam [Department of Physics, Thiagarajar College of Engineering, Madurai, Tamil Nadu (India); Sagadevan, Suresh, E-mail: duraiphysics2011@gmail.com [Department of Physics, AMET University (India)

    2016-03-15

    Cerium oxide (CeO{sub 2}) nanoparticles were prepared by the precipitation method. The average crystallite size of cerium oxide nanoparticles was calculated from the X-ray diffraction (XRD) pattern and found to be 11 nm. The FT-IR spectrum clearly indicated the strong presence of cerium oxide nanoparticles. Raman spectrum confirmed the cubic nature of the cerium oxide nanoparticles. The Scanning Electron Microscopy (SEM) analysis showed that the nanoparticles agglomerated forming spherical-shaped particles. The Transmission Electron Microscopic (TEM) analysis confirmed the prepared cerium oxide nanoparticles with the particle size being found to be 16 nm. The optical absorption spectrum showed a blue shift by the cerium oxide nanoparticles due to the quantum confinement effect. The dielectric properties of cerium oxide nanoparticles were studied for different frequencies at different temperatures. The dielectric constant and the dielectric loss of the cerium oxide nanoparticles decreased with increase in frequency. The AC electrical conductivity study revealed that the conduction depended on both the frequency and the temperature. (author)

  4. Study of the cerium(IV)-picrate system in acetonitrile.

    Science.gov (United States)

    Kratochvil, B; Tipler, M; McKay, B

    1966-07-01

    A potentiometric and spectrophotometric study has been made of the reaction between hexanitratocerate and picrate in dry acetonitrile. Several cerium(IV)-picrate complexes are formed; the formation constant for the first is estimated to be 4 from spectrophotometric measurements. The catalytic effect of picrate on hydroquinone oxidation by nitratocerate is postulated to be due to more rapid electron transfer by cerium picrate complexes.

  5. The Genotoxicity of Titanium Dioxide and Cerium Dioxide Nanoparticles in Human Respiratory Epithelial Cells

    Science.gov (United States)

    Due to the exponential growth of the nanomaterial industry, risk assessment of human exposure to nanomaterials in consumer products is of paramount importance. The genotoxicity of nanomaterials is an important aspect of hazard identification and regulatory guidance. However, this...

  6. Genotoxic Effects of Titanium Dioxide and Cerium Dioxide Nanoparticles in Human Respiratory Epithelial Cells

    Science.gov (United States)

    The nanomaterial industry has recently seen rapid growth, therefore, the risk assessment of human exposure to nanomaterials in consumer products is of paramount importance. The genotoxicity of nanomaterials is a fundamental aspect of hazard identification and regulatory guidance....

  7. Cerium-tannic acid passivation treatment on galvamzed steel

    Institute of Scientific and Technical Information of China (English)

    LIU Guangming; YU Fei; YANG Liu; TIAN Jihong; DU Nan

    2009-01-01

    A novel cerium-tannic acid passivation treatment was performed on galvanized steel. The corrosion resistance of cerium-tannic passivated samples was tested by dropping test with 0.5 wt.% CuSO4 aqueous solution. The mass loss per unit area of passivated samples was measured after the corrosion in 0.5 mol/L NaCl + 0.005 mol/L H2SO4 at room temperature for 96 h. The electrochemical behaviors of cerium, tannic acid, and cerium-tannic acid passivated samples on galvanized steel in 0.5 mol/L NaCI solution were investigated by polarization curves and electrochemical impendence spectra. The corrosion equivalent circuit was established according to the impedance characteristics. The results show that cerium-tannic acid treated samples exhibit better corrosion resistance than the sole cerium or tannic acid treated samples under the same condition. The mechanism of synergistic effect for cerium-tannic acid passivation on galvanized steel was discussed.

  8. Photodissociation of Cerium Oxide Nanocluster Cations.

    Science.gov (United States)

    Akin, S T; Ard, S G; Dye, B E; Schaefer, H F; Duncan, M A

    2016-04-21

    Cerium oxide cluster cations, CexOy(+), are produced via laser vaporization in a pulsed nozzle source and detected with time-of-flight mass spectrometry. The mass spectrum displays a strongly preferred oxide stoichiometry for each cluster with a specific number of metal atoms x, with x ≤ y. Specifically, the most prominent clusters correspond to the formula CeO(CeO2)n(+). The cluster cations are mass selected and photodissociated with a Nd:YAG laser at either 532 or 355 nm. The prominent clusters dissociate to produce smaller species also having a similar CeO(CeO2)n(+) formula, always with apparent leaving groups of (CeO2). The production of CeO(CeO2)n(+) from the dissociation of many cluster sizes establishes the relative stability of these clusters. Furthermore, the consistent loss of neutral CeO2 shows that the smallest neutral clusters adopt the same oxidation state (IV) as the most common form of bulk cerium oxide. Clusters with higher oxygen content than the CeO(CeO2)n(+) masses are present with much lower abundance. These species dissociate by the loss of O2, leaving surviving clusters with the CeO(CeO2)n(+) formula. Density functional theory calculations on these clusters suggest structures composed of stable CeO(CeO2)n(+) cores with excess oxygen bound to the surface as a superoxide unit (O2(-)).

  9. Atomic Transition Probabilities for Neutral Cerium

    Science.gov (United States)

    Chisholm, John; Nitz, D.; Sobeck, J.; Den Hartog, E. A.; Wood, M. P.; Lawler, J. E.

    2010-01-01

    Among the rare earth species, the spectra of neutral cerium (Ce I) and singly ionized cerium (Ce II) are some of the most complex. Like other rare earth species, Ce has many lines in the visible which are suitable for elemental abundance studies. Recent work on Ce II transition probabilities [1] is now being augmented with similar work on Ce I for future studies using such lines from astrophysical sources. Radiative lifetimes from laser induced fluorescence measurements [2] on neutral Ce are being combined with emission branching fractions from spectra recorded using a Fourier transform spectrometer. A total of 14 high resolution spectra are being analyzed to determine branching fractions for 2500 to 3000 lines from 153 upper levels in neutral Ce. Representative data samples and progress to date will be presented. This work was supported by the National Science Foundation's REU program and the Department of Defense's ASSURE program through NSF Award AST-0453442 and NSF Grant CTS0613277. [1] J. E. Lawler, C. Sneden, J. J. Cowan, I. I. Ivans, and E. A. Den Hartog, Astrophys. J. Suppl. Ser. 182, 51-79 (2009). [2] E. A. Den Hartog, K. P. Buettner, and J. E. Lawler, J. Phys. B: Atomic, Molecular & Optical Physics 42, 085006 (7pp) (2009).

  10. Molecular and physiological responses to titanium dioxide ...

    Science.gov (United States)

    - Changes in tissue transcriptomes and productivity of Arabidopsis thaliana were investigated during exposure of plants to two widely-used engineered metal oxide nanoparticles, titanium dioxide (nano-titanium) and cerium dioxide (nano-cerium). Microarray analyses confirmed that exposure to either nanoparticle altered the transcriptomes of rosette leaves and roots, with comparatively larger numbers of differentially expressed genes (DEGs) found under nano-titania exposure. Nano-titania induced more DEGs in rosette leaves, whereas roots had more DEGs under nano-ceria exposure. MapMan analyses indicated that while nano-titania up-regulated overall and secondary metabolism in both tissues, metabolic processes under nano-ceria remained mostly unchanged. Gene enrichment analysis indicated that both nanoparticles mainly enriched ontology groups such as responses to stress (abiotic and biotic), and defense responses (pathogens), and responses to endogenous stimuli (hormones). Nano-titania specifically induced genes associated with photosynthesis, whereas nano-ceria induced expression of genes related to activating transcription factors, most notably those belonging to the ethylene responsive element binding protein family. Interestingly, there were also increased numbers of rosette leaves and plant biomass under nano-ceria exposure, but not under nano-titania. Other transcriptomic responses did not clearly relate to responses observed at the organism level. This may b

  11. Improvement in corrosion resistance of magnesium coating with cerium treatment

    Institute of Scientific and Technical Information of China (English)

    Samia Ben Hassen; Latifa Bousselmi; Patricc Bercot; El Mustafa Rezrazi; Ezzeddine Triki

    2009-01-01

    Corrosion protection afforded by a magnesium coating treated in cerium salt solution on steel substrate was investigated using open circuit potential, polarization curves, and electrochemical impedance spectroscopy (EIS) in 0.005 M sodium chloride solution (NaCl). The morphology of the surface was characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The cerium treated coating was obtained by immersion in CeCl3 solution. The results showed that the corrosion resistance of the treated magnesium coating was improved. The corrosion potential of the treated coating was found to be nobler than that of the untreated magnesium coating and the corrosion current decreased significantly. Impedance results showed that the cerium treatment increased corrosion protection. The improvement of anti-corrosion properties was ataibuted to the formation of cerium oxides and hydroxides that gave to a physical barrier effect.

  12. Heteroaggregation of cerium oxide nanoparticles and nanoparticles of pyrolyzed biomass

    Science.gov (United States)

    Heteroaggregation with indigenous particles is an important process controlling the mobility of engineered nanomaterials in the environment. We studied heteroaggregation of cerium oxide nanoparticles (n-CeO2), which are widely used commercially, with nanoparticles of pyrogenic carbonaceous material ...

  13. Preparing Process of Cerium Acetate and Rare Earth Acetate

    Institute of Scientific and Technical Information of China (English)

    Qiao Jun; Ma Ying; Xu Yanhui; Zhang Jun; Chang Shu; Hao Xianku

    2004-01-01

    Preparing process was presented and the influences of concentration of acetic acid, reaction temperature, the ratio of cerium carbonate and acetic acid, heat preservation time to the yield of cerium acetate were discussed.The crystalline cerium acetate and rare earth acetate such as ( La, Ce, Pr, Nd) (Ac) 3, ( Ce, Pr, Nd) (Ac) 3, ( Pr, Nd, Er,Y) (Ac) 3 and yttrium acetate were prepared under this condition.The shape, structure and composition of the crystals were determined by the methods of SEM, TG-DTA, X-ray diffraction and chemical analysis.The optimum prepared conditions of cerium acetate were described.This prepared process has characteristics such as simple process route, low cost, high yield, good quality, no pollution to environment, etc.

  14. Cerium intermetallics CeTX. Review III

    Energy Technology Data Exchange (ETDEWEB)

    Poettgen, Rainer; Janka, Oliver [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Chevalier, Bernard [Bordeaux Univ., Pessac (France). Inst. de Chimie de la Matiere Condensee de Bordeaux

    2016-05-01

    The structure-property relationships of CeTX intermetallics with structures other than the ZrNiAl and TiNiSi type are systematically reviewed. These CeTX phases form with electron-poor and electron-rich transition metals (T) and X = Mg, Zn, Cd, Hg, Al, Ga, In, Tl, Si, Ge, Sn, Pb, P, As, Sb, and Bi. The review focusses on the crystal chemistry, the chemical bonding peculiarities, and the magnetic and transport properties. Furthermore {sup 119}Sn Moessbauer spectroscopic data, high-pressure studies, hydrogenation reactions and the formation of solid solutions are reviewed. This paper is the third of a series of four reviews on equiatomic intermetallic cerium compound [Part I: R. Poettgen, B. Chevalier, Z. Naturforsch. 2015, 70b, 289; Part II: R. Poettgen, B. Chevalier, Z. Naturforsch. 2015, 70b, 695].

  15. Simple cerium-triethanolamine complex: Synthesis, characterization, thermal decomposition and its application to prepare ceria support for platinum catalysts used in methane steam reforming

    Science.gov (United States)

    Wattanathana, Worawat; Nootsuwan, Nollapan; Veranitisagul, Chatchai; Koonsaeng, Nattamon; Laosiripojana, Navadol; Laobuthee, Apirat

    2015-06-01

    Cerium-triethanolamine complex was synthesized by simple complexation method in 1-propanol solvent using cerium(III) chloride as a metal source and triethanolamine as a ligand. The structures of the prepared complex were proposed based on FT-IR, FT-Raman and ESI-MS results as equimolar of triethanolamine and cerium chelated complex having monomeric tricyclic structure with and without chloride anion as another coordinating group known as ceratrane. The complex was used as a precursor for ceria material done by thermal decomposition. XRD result revealed that when calcined at 600 °C for 2 h, the cerium complex was totally turned into pure ceria with cubic fluorite structure. The obtained ceria was then employed to synthesize platinum doped ceria catalysts for methane steam reforming. Various amounts of platinum i.e. 1, 3, 5 and 10 mol percents were introduced on the ceria support by microwave-assisted wetness impregnation using ammonium tetrachloroplatinate(II). The platinum-impregnated ceria powders were subjected to calcination in 10% hydrogen/helium atmosphere at 500 °C for 3 h to reduce platinum(II) to platinum(0). XRD patterns of the catalysts confirmed that the platinum particles doped on the ceria support were in the form of platinum(0). Catalytic activity test showed that the catalytic activities got higher as the amounts of platinum doped increased. Besides, the portions of coke formation on the surface of catalysts were reduced as the amounts of platinum doped increased.

  16. Exraction and separation of CERIUM(IV)/FLUORINE in fluoride-bearing cerium sulfate solution with fluoride coordination agent

    OpenAIRE

    Li, Y; J. G. He; X. X. Xue; Ru, H. Q.; X. W. Huang; Yang, H.

    2014-01-01

    In this paper the extraction and separation of cerium/fluorine in fluoride-bearing cerium sulfate solution with fluoride coordination agent has been studied. The UV-vis spectra suggest that Zr6+ and Al3+ can scrub the F- from [CeF2] 2+ complex. The separation and conductivity studies show that aluminum salt is the most suitable fluoride coordination agent, and an ion-exchange reaction is involved between Ce4+/ [CeF2] 2+ and hydrogen ion.

  17. Sixth form pure mathematics

    CERN Document Server

    Plumpton, C

    1968-01-01

    Sixth Form Pure Mathematics, Volume 1, Second Edition, is the first of a series of volumes on Pure Mathematics and Theoretical Mechanics for Sixth Form students whose aim is entrance into British and Commonwealth Universities or Technical Colleges. A knowledge of Pure Mathematics up to G.C.E. O-level is assumed and the subject is developed by a concentric treatment in which each new topic is used to illustrate ideas already treated. The major topics of Algebra, Calculus, Coordinate Geometry, and Trigonometry are developed together. This volume covers most of the Pure Mathematics required for t

  18. Sorptive separation of yttrium and cerium on a weakly basic anionite

    Science.gov (United States)

    Cheremisina, O. V.; Ponomareva, M. A.; Chirkst, D. E.; Lobacheva, O. L.; Shul'gin, I. A.

    2015-01-01

    The sorption of complex yttrium ions with Trilon B onto the weakly basic anionite D-403 in nitrate form from an acidic medium at pH 3 with constant ionic strength (NaNO3, 1 mol/kg) is investigated. A thermodynamic evaluation of the sorption isotherm of anionic yttrium complexes is performed using a method based on the linearization of the equation of the law of active mass, modified for ionic exchange reactions. The ionic exchange constant, the Gibbs free energy of ionic exchange, the capacity of the anionite, and the sorption limit of ethylenediaminetetraacetatoyttrate ions (EDTA yttrate ions) are calculated. Using a frontal version of ion exchange chromatography, cerium and yttrium are separated on D-403 anionite with a fraction of pure yttrium at the column outlet of no less than 30%.

  19. Cerium oxide dispersed multi walled carbon nanotubes as cathode material for flexible field emitters.

    Science.gov (United States)

    Baby, Tessy Theres; Rakhi, R B; Ravi, N; Ramaprabhu, S

    2012-08-01

    Nanomaterials based electron sources are omnipresent in modern flat panel displays. Multi walled carbon nanotubes (MWNT) are the well studied electron emitter among the carbon materials. Since the surface modification of MWNT with low work function materials would have a positive impact on the field emission property of MWNT, cerium oxide (CeO2) nanoparticles dispersed multi walled carbon nanotubes (CeO2/MWNT) were synthesized by catalytic chemical vapour deposition followed by chemical reduction and its field emission property was investigated. The high-purity MWNT as well as CeO2/MWNT showed crystalline structure conformed by X-ray diffraction (XRD) and thermogravimetric analysis (TGA). Further characterisation was done with Raman spectroscopy, UV-Visible absorption spectra and Fourier transform IR spectroscopy (FT-IR). The morphology and structural details of CeO2/MWNT composite was probed by field-emission scanning electron microscopy (FESEM) and energy dispersive X-ray analysis (EDX). The direct evidence of the formation of CeO2/MWNT composites was given by transmission electron microscopy (TEM). The synthesized sample was coated over a flexible carbon paper using spin coating technique. The experiment was performed under a vacuum of 1 x 10(-6) Torr and Fowler-Nordheim equation was used to analyse the data. The turn-on voltage for the cerium oxide dispersed MWNT was found for a current density of 10 microA/cm2. The emission current density from the CeO2 nanoparticles dispersed MWNT reached 0.2 mA/cm2 at a reasonable bias field of 2.58 V/microm. The results were compared with those of pure MWNT and pure CeO2 nanoparticles with literature values.

  20. Inhibition of pH fronts in corrosion cells due to the formation of cerium hydroxide

    NARCIS (Netherlands)

    Soestbergen, M. van; Erich, S.J.F.; Huinink, H.P.; Adan, O.C.G.

    2013-01-01

    The effect of cerium-based corrosion inhibitors on the pH front between the alkaline cathode and acidic anode in corrosion cells has been studied. The cerium component of these inhibitors can affect the pH front since it precipitates in an alkaline environment as cerium hydroxide, which is important

  1. Potential for recovery of cerium contained in automotive catalytic converters

    Science.gov (United States)

    Bleiwas, Donald I.

    2013-01-01

    Catalytic converters (CATCONs) are required by Federal law to be installed in nearly all gasoline- and diesel-fueled onroad vehicles used in the United States. About 85 percent of the light-duty vehicles and trucks manufactured worldwide are equipped with CATCONs. Portions of the CATCONs (called monoliths) are recycled for their platinum-group metal (PGM) content and for the value of the stainless steel they contain. The cerium contained in the monoliths, however, is disposed of along with the slag produced from the recycling process. Although there is some smelter capacity in the United States to treat the monoliths in order to recover the PGMs, a great percentage of monoliths is exported to Europe and South Africa for recycling, and a lesser amount is exported to Japan. There is presently no commercial-scale capacity in place domestically to recover cerium from the monoliths. Recycling of cerium or cerium compounds from the monoliths could help ensure against possible global supply shortages by increasing the amount that is available in the supply chain as well as the number and geographic distribution of the suppliers. It could also reduce the amount of material that goes into landfills. Also, the additional supply could lower the price of the commodity. This report analyzes how much cerium oxide is contained in CATCONs and how much could be recovered from used CATCONs.

  2. Electrodeposited cerium film as chromate replacement for tinplate

    Energy Technology Data Exchange (ETDEWEB)

    Huang Xingqiao [Department of Applied Chemistry, Harbin Institute of Technology, Harbin 150001 (China); Li Ning [Department of Applied Chemistry, Harbin Institute of Technology, Harbin 150001 (China)], E-mail: lining@hit.edu.cn; Wang Huiyong; Sun Hanxiao; Sun Shanshan; Zheng Jian [Department of Applied Chemistry, Harbin Institute of Technology, Harbin 150001 (China)

    2008-01-30

    The cerium film was prepared on tinplate by electrodeposition method. Sulfide-stain resistance of the Ce-passivated, unpassivated and Cr-passivated tinplates was evaluated using a cysteine tarnish test. Corrosion behavior of these tinplates in contact with 3.5% NaCl solution and 0.1 M citric-citrate buffer solution was investigated using Tafel measurement and electrochemical impedance spectroscopy measurement, respectively. The adhesion of epoxyphenolic lacquer to the Ce-passivated tinplate was checked using a cross hatch cutter. The morphology, composition and thickness of the cerium film were studied by atomic force microscopy, X-ray photoelectron spectroscopy and X-ray fluorescence spectrometry. According to the results, the Ce-passivated tinplate shows the best sulfide-stain resistance and the best corrosion protection property compared with the unpassivated and Cr-passivated tinplates. The adhesion of epoxyphenolic lacquer to the Ce-passivated tinplate is good. The cerium film is composed of the closely packed particles of about 50-200 nm in diameter. The film mainly consists of cerium and oxygen, which mainly exist as CeO{sub 2}, Ce{sub 2}O{sub 3} and their hydrates such as Ce(OH){sub 4}, Ce(OH){sub 3}. The total cerium amount of the film is about 0.110 g/m{sup 2}.

  3. Cerium, manganese and cerium/manganese ceramic monolithic catalysts. Study of VOCs and PM removal

    Institute of Scientific and Technical Information of China (English)

    COLMAN-LERNER Esteban; PELUSO Miguel Andrs; SAMBETH Jorge; THOMAS Horacio

    2016-01-01

    Ceramic supported cerium, manganese and cerium-manganese catalysts were prepared by direct impregnation of aqueous precursor, and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Brunauer-Emmett-Teller method (BET), temperature programmed reduction (H2-TPR), X-ray photoelectron spectroscopy (XPS) acidity measurements and electrical conductivity. The catalytic activity was evaluated for volatile organic compounds (VOC) (ethanol, methyl ethyl ketone and toluene) oxidation. Additionally, catalysts were tested in particulate matter (PM) combustion. The characterization results indicated that Ce was in the form of Ce4+ and Ce3+, and Mn existed in the form of Mn4+and Mn3+on the surface of the Mn/AC sample and in the form of Mn4+ in the Ce/Mn/AC monolith. VOC oxidation results revealed that the Ce/Mn/AC sample showed an excellent performance compared with ceramic supported CeO2 (Ce/AC) and MnOx (Mn/AC) samples. The PM combustion was also higher on Ce/Mn/AC monoliths. The enhanced catalytic activity was mainly attributed to the Ce and Mn interaction which enhanced the acidity, conductiv-ity and the reducibility of the oxides.

  4. Cerium-iron-based magnetic compounds

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Chen; Pinkerton, Frederick E.; Herbst, Jan F.

    2017-01-17

    New magnetic materials containing cerium, iron, and small additions of a third element are disclosed. These materials comprise compounds Ce(Fe.sub.12-xM.sub.x) where x=1-4, having the ThMn.sub.12 tetragonal crystal structure (space group I4/mmm, #139). Compounds with M=B, Al, Si, P, S, Sc, Co, Ni, Zn, Ga, Ge, Zr, Nb, Hf, Ta, and W are identified theoretically, and one class of compounds based on M=Si has been synthesized. The Si cognates are characterized by large magnetic moments (4.pi.M.sub.s greater than 1.27 Tesla) and high Curie temperatures (264.ltoreq.T.sub.c.ltoreq.305.degree. C.). The Ce(Fe.sub.12-xM.sub.x) compound may contain one or more of Ti, V, Cr, and Mo in combination with an M element. Further enhancement in T.sub.c is obtained by nitriding the Ce compounds through heat treatment in N.sub.2 gas while retaining the ThMn.sub.12 tetragonal crystal structure; for example CeFe.sub.10Si.sub.2N.sub.1.29 has T.sub.c=426.degree. C.

  5. Mechanical and Thermophysical Properties of Cerium Monopnictides

    Science.gov (United States)

    Bhalla, Vyoma; Singh, Devraj; Jain, S. K.

    2016-03-01

    The ultrasonic attenuation due to phonon-phonon interaction, thermoelastic relaxation and dislocation damping mechanisms has been investigated in cerium monopnictides CeX (X: N, P, As, Sb and Bi) for longitudinal and shear waves along {third-order elastic constants of CeX have also been computed in the temperature range 0 K to 500 K using Coulomb and Born-Mayer potential upto second nearest neighbours. The computed values of these elastic constants have been applied to find out Young's moduli, bulk moduli, Breazeale's non-linearity parameters, Zener anisotropy, ultrasonic velocity, ultrasonic Grüneisen parameter, thermal relaxation time, acoustic coupling constants and ultrasonic attenuation. The fracture/toughness ratio is less than 1.75, which shows that the chosen materials are brittle in nature as found for other monopnictides. The drag coefficient acting on the motion of screw and edge dislocations due to shear and compressional phonon viscosities of the lattice have also been evaluated for both the longitudinal and shear waves. The thermoelastic loss and dislocation damping loss are negligible in comparison to loss due to Akhieser damping (phonon-phonon interaction). The obtained results for CeX are in qualitative agreement with other semi-metallic monopnictides.

  6. Rehabilitation of pure alexia

    DEFF Research Database (Denmark)

    Starrfelt, Randi; Ólafsdóttir, Rannveig Rós; Arendt, Ida-Marie

    2013-01-01

    Acquired reading problems caused by brain injury (alexia) are common, either as a part of an aphasic syndrome, or as an isolated symptom. In pure alexia, reading is impaired while other language functions, including writing, are spared. Being in many ways a simple syndrome, one would think...... that pure alexia was an easy target for rehabilitation efforts. We review the literature on rehabilitation of pure alexia from 1990 to the present, and find that patients differ widely on several dimensions like alexia severity, and associated deficits. Many patients reported to have pure alexia...... in the reviewed studies, have associated deficits like agraphia or aphasia and thus do not strictly conform to the diagnosis. Few studies report clear and generalisable effects of training, none report control data, and in many cases the reported findings are not supported by statistics. We can, however...

  7. Rehabilitation of pure alexia

    DEFF Research Database (Denmark)

    Starrfelt, Randi; Ólafsdóttir, Rannveig Rós; Arendt, Ida-Marie

    2013-01-01

    that pure alexia was an easy target for rehabilitation efforts. We review the literature on rehabilitation of pure alexia from 1990 to the present, and find that patients differ widely on several dimensions like alexia severity, and associated deficits. Many patients reported to have pure alexia......Acquired reading problems caused by brain injury (alexia) are common, either as a part of an aphasic syndrome, or as an isolated symptom. In pure alexia, reading is impaired while other language functions, including writing, are spared. Being in many ways a simple syndrome, one would think...... in the reviewed studies, have associated deficits like agraphia or aphasia and thus do not strictly conform to the diagnosis. Few studies report clear and generalisable effects of training, none report control data, and in many cases the reported findings are not supported by statistics. We can, however...

  8. Elaboration and characterization of thin solid films containing cerium

    Science.gov (United States)

    Hamdi, S.; Guerfi, S.; Siab, R.

    2009-11-01

    Cerium oxide films are widely studied as a promising alternative to Cr(VI) based pre-treatments for the corrosion protection of different metals and alloys. Cathodic electrodeposition of Cerium containing thin films was realised on TA6V substrates from a Ce(NO3)3, 6H2O and mixed water-ethyl alcohol solutions at 0.01 M. Experimental conditions to obtain homogeneous and crack free thin films were determined. The deposited cerium quantity appears proportional to the quantity of electricity used, as indicated by the Faraday law. Subsequent thermal treatment lead to a CeO2 coating, expected to provide an increase of TA6V oxidation resistance at high temperatures. The deposits were characterized by differential scanning calorimetry (DSC), optical and scanning electron microscopies.

  9. Thermodynamic Calculation among Cerium, Oxygen, and Sulfur in Liquid Iron

    Science.gov (United States)

    Pan, Fei; Zhang, Jian; Chen, Hao-Long; Su, Yen-Hsun; Su, Yen-Hao; Hwang, Weng-Sing

    2016-10-01

    Thermodynamic calculation has been applied to predict the inclusion formation in molten SS400 steel. When the Cerium addition in liquid iron is 70 ppm and the initial Oxygen and Sulphur are both 110 ppm, the formation of oxides containing Cerium would experience the transformation from Ce2O3 to CeO2 and also the formation of sulfides containing Cerium would experience the transformation from CeS to Ce2S3 and then to Ce3S4. Below 2000 K the most thermodynamic stable matter is CeO2 and the less thermodynamic stable inclusion is CeS. Only when the amount of [O] is extremely low and the amount of [S] and [Ce] is relatively high, Ce2S3 has the possibility to form.

  10. Synthesis and characterization of magnesium doped cerium oxide for the fuel cell application

    Science.gov (United States)

    Kumar, Amit; Kumari, Monika; Kumar, Mintu; Kumar, Sacheen; Kumar, Dinesh

    2016-05-01

    Cerium oxide has attained much attentions in global nanotechnology market due to valuable application for catalytic, fuel additive, and widely as electrolyte in solid oxide fuel cell. Doped cerium oxide has large oxygen vacancies that allow for greater reactivity and faster ion transport. These properties make cerium oxide suitable material for SOFCs application. Cerium oxide electrolyte requires lower operation temperature which shows improvement in processing and the fabrication technique. In our work, we synthesized magnesium doped cerium oxide by the co-precipitation method. With the magnesium doping catalytic reactivity of CeO2 was increased. Synthesized nanoparticle were characterized by the XRD and UV absorption techniques.

  11. Isomorphic phase transformation in shocked Cerium using molecular dynamics

    OpenAIRE

    Germann T.C.; Chen S.-P.; Dupont V.

    2011-01-01

    Cerium (Ce) undergoes a significant (∼16%) volume collapse associated with an isomorphic fcc-fcc phase transformation when subject to compressive loading. We present here a new Embedded Atom Method (EAM) potential for Cerium that models two minima for the two fcc phases. We show results from its use in Molecular Dynamics (MD) simulations of Ce samples subjected to shocks with pressures ranging from 0.5 to 25 GPa. A split wave structure is observed, with an elastic precursor followed by a plas...

  12. Optical and electrical studies of cerium mixed oxides

    Science.gov (United States)

    Sherly, T. R.; Raveendran, R.

    2014-10-01

    The fast development in nanotechnology makes enthusiastic interest in developing nanomaterials having tailor made properties. Cerium mixed oxide materials have received great attention due to their UV absorption property, high reactivity, stability at high temperature, good electrical property etc and these materials find wide applications in solid oxide fuel cells, solar control films, cosmetics, display units, gas sensors etc. In this study cerium mixed oxide compounds were prepared by co-precipitation method. All the samples were doped with Zn (II) and Fe (II). Preliminary characterizations such as XRD, SEM / EDS, TEM were done. UV - Vis, Diffuse reflectance, PL, FT-IR, Raman and ac conductivity studies of the samples were performed.

  13. Cerium fluoride nanoparticles protect cells against oxidative stress.

    Science.gov (United States)

    Shcherbakov, Alexander B; Zholobak, Nadezhda M; Baranchikov, Alexander E; Ryabova, Anastasia V; Ivanov, Vladimir K

    2015-05-01

    A novel facile method of non-doped and fluorescent terbium-doped cerium fluoride stable aqueous sols synthesis is proposed. Intense green luminescence of CeF3:Tb nanoparticles can be used to visualize these nanoparticles' accumulation in cells using confocal laser scanning microscopy. Cerium fluoride nanoparticles are shown for the first time to protect both organic molecules and living cells from the oxidative action of hydrogen peroxide. Both non-doped and terbium-doped CeF3 nanoparticles are shown to provide noteworthy protection to cells against the vesicular stomatitis virus. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. Optical and electrical studies of cerium mixed oxides

    Energy Technology Data Exchange (ETDEWEB)

    Sherly, T. R., E-mail: trsherly@gmail.com [Post Graduate Department of Physics, Sanathana Dharma College, Alappuzha, Kerala (India); Raveendran, R. [Nanoscience Research Laboratory, Sree Narayana College, Kollam, Kerala 691001 (India)

    2014-10-15

    The fast development in nanotechnology makes enthusiastic interest in developing nanomaterials having tailor made properties. Cerium mixed oxide materials have received great attention due to their UV absorption property, high reactivity, stability at high temperature, good electrical property etc and these materials find wide applications in solid oxide fuel cells, solar control films, cosmetics, display units, gas sensors etc. In this study cerium mixed oxide compounds were prepared by co-precipitation method. All the samples were doped with Zn (II) and Fe (II). Preliminary characterizations such as XRD, SEM / EDS, TEM were done. UV - Vis, Diffuse reflectance, PL, FT-IR, Raman and ac conductivity studies of the samples were performed.

  15. Exraction and separation of CERIUM(IV/FLUORINE in fluoride-bearing cerium sulfate solution with fluoride coordination agent

    Directory of Open Access Journals (Sweden)

    Y. Li

    2014-07-01

    Full Text Available In this paper the extraction and separation of cerium/fluorine in fluoride-bearing cerium sulfate solution with fluoride coordination agent has been studied. The UV-vis spectra suggest that Zr6+ and Al3+ can scrub the F- from [CeF2] 2+ complex. The separation and conductivity studies show that aluminum salt is the most suitable fluoride coordination agent, and an ion-exchange reaction is involved between Ce4+/ [CeF2] 2+ and hydrogen ion.

  16. Pure-tone Audiometer

    Science.gov (United States)

    Kapul, A. A.; Zubova, E. I.; Torgaev, S. N.; Drobchik, V. V.

    2017-08-01

    The research focuses on a pure-tone audiometer designing. The relevance of the study is proved by high incidence of an auditory analyser in older people and children. At first, the article provides information about subjective and objective audiometry methods. Secondly, we offer block-diagram and basic-circuit arrangement of device. We decided to base on STM32F407VG microcontroller and use digital pot in the function of attenuator. Third, we implemented microcontroller and PC connection. C programming language is used for microcontroller’s program and PC’s interface. Fourthly, we created the pure-tone audiometer prototype. In the future, we will implement the objective method ASSR in addition to pure-tone audiometry.

  17. Effect of variable cerium concentration on photoluminescence behaviour in ZrO2 phosphor synthesized by combustion synthesis method

    Science.gov (United States)

    Dubey, Vikas; Kaur, Jagjeet

    2016-05-01

    Present paper reports synthesis and characterization of trivalent cerium (Ce3+) doped zirconium dioxide (ZrO2) phosphors. Effect of variable concentration of cerium on photoluminescence (PL) is studied. Samples were prepared by combustion synthesis technique which is suitable for less time taking techniques also for large scale production for phosphors. Starting material used for sample preparation are Zr(NO3)3 and Ce(NO3)3 and urea used as a fuel. All prepared phosphor with variable concentration of Ce3+ (0.1 to 2mol%) was studied by photoluminescence analysis it is found that the excitation spectra of prepared phosphor shows broad excitation centred at 390nm. The excitation spectra with variable concentration of Ce3+ show strong peaks at 447nm. Spectrophotometric determinations of peaks are evaluated by Commission Internationale de I'Eclairage technique. Using this phosphor, the desired CIE values including emissions throughout the violet (390 nm) and blue (427 nm) of the spectra were achieved. Efficient blue light emitting diodes were fabricated using Ce3+ doped phosphor based on near ultraviolet (NUV) excited LED lights.

  18. Effect of variable cerium concentration on photoluminescence behaviour in ZrO{sub 2} phosphor synthesized by combustion synthesis method

    Energy Technology Data Exchange (ETDEWEB)

    Dubey, Vikas, E-mail: jsvikasdubey@gmail.com [Department of Physics, Bhilai Institute of Technology, Raipur, 493661 (India); Kaur, Jagjeet [Department of Physics, Govt. V.Y.T. PG. Auto. College, Durg (India)

    2016-05-06

    Present paper reports synthesis and characterization of trivalent cerium (Ce{sup 3+}) doped zirconium dioxide (ZrO{sub 2}) phosphors. Effect of variable concentration of cerium on photoluminescence (PL) is studied. Samples were prepared by combustion synthesis technique which is suitable for less time taking techniques also for large scale production for phosphors. Starting material used for sample preparation are Zr(NO{sub 3}){sub 3} and Ce(NO{sub 3}){sub 3} and urea used as a fuel. All prepared phosphor with variable concentration of Ce{sup 3+} (0.1 to 2mol%) was studied by photoluminescence analysis it is found that the excitation spectra of prepared phosphor shows broad excitation centred at 390nm. The excitation spectra with variable concentration of Ce{sup 3+} show strong peaks at 447nm. Spectrophotometric determinations of peaks are evaluated by Commission Internationale de I’Eclairage technique. Using this phosphor, the desired CIE values including emissions throughout the violet (390 nm) and blue (427 nm) of the spectra were achieved. Efficient blue light emitting diodes were fabricated using Ce{sup 3+} doped phosphor based on near ultraviolet (NUV) excited LED lights.

  19. Processing and Characterization of Sol-Gel Cerium Oxide Microspheres

    Energy Technology Data Exchange (ETDEWEB)

    McClure, Zachary D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Padilla Cintron, Cristina [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-09-27

    Of interest to space exploration and power generation, Radioisotope Thermoelectric Generators (RTGs) can provide long-term power to remote electronic systems without the need for refueling or replacement. Plutonium-238 (Pu-238) remains one of the more promising materials for thermoelectric power generation due to its high power density, long half-life, and low gamma emissions. Traditional methods for processing Pu-238 include ball milling irregular precipitated powders before pressing and sintering into a dense pellet. The resulting submicron particulates of Pu-238 quickly accumulate and contaminate glove boxes. An alternative and dust-free method for Pu-238 processing is internal gelation via sol-gel techniques. Sol-gel methodology creates monodisperse and uniform microspheres that can be packed and pressed into a pellet. For this study cerium oxide microspheres were produced as a surrogate to Pu-238. The similar electronic orbitals between cerium and plutonium make cerium an ideal choice for non-radioactive work. Before the microspheres can be sintered and pressed they must be washed to remove the processing oil and any unreacted substituents. An investigation was performed on the washing step to find an appropriate wash solution that reduced waste and flammable risk. Cerium oxide microspheres were processed, washed, and characterized to determine the effectiveness of the new wash solution.

  20. Purification of cerium, neodymium and gadolinium for low background experiments

    Directory of Open Access Journals (Sweden)

    Boiko R.S.

    2014-01-01

    Full Text Available Cerium, neodymium and gadolinium contain double beta active isotopes. The most interesting are 150Nd and 160Gd (promising for 0ν2β search, 136Ce (2β+ candidate with one of the highest Q2β. The main problem of compounds containing lanthanide elements is their high radioactive contamination by uranium, radium, actinium and thorium. The new generation 2β experiments require development of methods for a deep purification of lanthanides from the radioactive elements. A combination of physical and chemical methods was applied to purify cerium, neodymium and gadolinium. Liquid-liquid extraction technique was used to remove traces of Th and U from neodymium, gadolinium and for purification of cerium from Th, U, Ra and K. Co-precipitation and recrystallization methods were utilized for further reduction of the impurities. The radioactive contamination of the samples before and after the purification was tested by using ultra-low-background HPGe gamma spectrometry. As a result of the purification procedure the radioactive contamination of gadolinium oxide (a similar purification efficiency was reached also with cerium and neodymium oxides was decreased from 0.12 Bq/kg to 0.007 Bq/kg in 228Th, from 0.04 Bq/kg to <0.006 Bq/kg in 226Ra, and from 0.9 Bq/kg to 0.04 Bq/kg in 40K. The purification methods are much less efficient for chemically very similar radioactive elements like actinium, lanthanum and lutetium.

  1. Cerium; crystal structure and position in the periodic table.

    Science.gov (United States)

    Johansson, Börje; Luo, Wei; Li, Sa; Ahuja, Rajeev

    2014-09-17

    The properties of the cerium metal have intrigued physicists and chemists for many decades. In particular a lot of attention has been directed towards its high pressure behavior, where an isostructural volume collapse (γ phase → α phase) has been observed. Two main models of the electronic aspect of this transformation have been proposed; one where the 4f electron undergoes a change from being localized into an itinerant metallic state, and one where the focus is on the interaction between the 4f electron and the conduction electrons, often referred to as the Kondo volume collapse model. However, over the years it has been repeatedly questioned whether the cerium collapse really is isostructural. Most recently, detailed experiments have been able to remove this worrisome uncertainty. Therefore the isostructural aspect of the α-γ transition has now to be seriously addressed in the theoretical modeling, something which has been very much neglected. A study of this fundamental characteristic of the cerium volume collapse is made in present paper and we show that the localized [rlhar2 ] delocalized 4f electron picture provides an adequate description of this unique behavior. This agreement makes it possible to suggest that an appropriate crossroad position for cerium in The Periodic Table.

  2. Structural, optical and photocatalytic activity of cerium doped zinc aluminate

    Science.gov (United States)

    Sumathi, Shanmugam; Kavipriya, A.

    2017-03-01

    Zinc aluminate and cerium-doped zinc aluminate nanoparticles are synthesised by co-precipitation method. Ammonium hydroxide is used as a precipitating agent. The synthesised compounds are characterised by powder X-ray diffraction (XRD), Fourier transform Infrared spectroscopy (FT-IR), Ultraviolet diffuse reflectance spectroscopy (UV-DRS), Thermogravimetric analysis (TGA), Scanning electron microscopy (SEM) and Surface area measurements. The photocatalytic activity of zinc aluminate and cerium doped zinc aluminate nanoparticles are studied under the UV light and visible light taking methylene blue as a model pollutant. The amount of catalyst, concentration of dye solution and time are optimised under UV-light. Degradation of methylene blue under the UV-light is found to be 99% in 20 min with 10 mg of cerium doped catalyst. Compared to visible light degradation, the degradation of dye under UV-light is higher. Cerium doping in zinc aluminate (ZnAl2O4:Ce3+) increased the photocatalytic activity of zinc aluminate.

  3. Progress on Radiative Transition Probabilities in Neutral Cerium

    Science.gov (United States)

    Curry, J. J.

    2009-10-01

    Cerium is a rare-earth atom that is currently used in energy-efficient metal-halide lamps because of its rich visible emission spectrum. More than 20,000 lines have been observed and classified for neutral cerium in the wavelength range of 340 nm to 1 μm (Bill Martin, unpublished). We recently derived more than 500 absolute transition probabilities from existing experimental data (J. Phys. D: Appl. Phys. 2009). Lawler and Den Hartog at the University of Wisconsin have made measurements that are expected to produce a few thousand transition probabilities. These advances, however, leave the data situation far short of what is needed to simulate an accurate global emission spectrum in numerical models of metal-halide lamps containing cerium. One possibility for closing this gap is through atomic structure calculations. Although it may be difficult for calculations to match the accuracy of measurements for any given transition, the global spectral distribution produced with calculated transition probabilities may still be satisfactory. For such a large number of lines, calculations may be the only realistic way to produce a reasonably complete set of data. We will discuss our recent atomic structure calculations of neutral cerium with the Cowan code based on a parametric fit of calculated energy level values to experimental values.

  4. Dahlbeck and Pure Ontology

    Science.gov (United States)

    Mackenzie, Jim

    2016-01-01

    This article responds to Johan Dahlbeck's "Towards a pure ontology: Children's bodies and morality" ["Educational Philosophy and Theory," vol. 46 (1), 2014, pp. 8-23 (EJ1026561)]. His arguments from Nietzsche and Spinoza do not carry the weight he supposes, and the conclusions he draws from them about pedagogy would be…

  5. Dahlbeck and Pure Ontology

    Science.gov (United States)

    Mackenzie, Jim

    2016-01-01

    This article responds to Johan Dahlbeck's "Towards a pure ontology: Children's bodies and morality" ["Educational Philosophy and Theory," vol. 46 (1), 2014, pp. 8-23 (EJ1026561)]. His arguments from Nietzsche and Spinoza do not carry the weight he supposes, and the conclusions he draws from them about pedagogy would be…

  6. Preparation, Characterization and Antibacterial Property of Cerium Substituted Hydroxyapatite Nanoparticles

    Institute of Scientific and Technical Information of China (English)

    Lin Yingguang; Yang Zhuoru; Cheng Jiang

    2007-01-01

    Nanoparticles of hydroxyapatite (HAP) and cerium substituted hydroxyapatite (CeHAP) with the atomic ratio of Ce/[Ca+Ce] (xCe) from 0 to 0.2 were prepared by sol-gel-supercritical fluid drying (SCFD) method. The nanoparticles were characterized by TEM, XRD, and FT-IR, and the effects of cerium on crystal structure, crystallinity, and particle shape were discussed. With the tests of bacterial inhibition zone and antibacterial ratio, the antibacterial property of HAP and CeHAP nanoparticles on Escherichia coli, Staphylococcus aureus, Lactobacillus were researched. Results showed that the nanoparticles of HAP and CeHAP could be made by sol-gel-SCFD, cerium could partially substitute for calcium and enter the structure of HAP. After substitution, the crystallinity, the IR wavenumbers of bonds in CeHAP decreased gradually with increase of cerium substitution, and the morphology of the nanoparticles changed from the short rod-shaped HAP to the needle-shaped CeHAP. The nanoparticles of HAP and CeHAP with xCe below 0.08 had antibacterial property only forcibly contacting with the test bacteria at the test concentration of 0.1 g·ml-1, however, the CeHAP nanoparticles had antibacterial ability at that concentration no matter statically or dynamically contacting with the test bacteria when xCe was above 0.08, and the antibacterial ability gets better with the increase of xCe, indicating that the antibacterial property was improved after calcium was partially substituted by cerium. The improved antibacterial effects of CeHAP nanoparticle on Lactobacillus showed its potential ability to anticaries.

  7. Varmeovergang og trykfald ved fordampning af kuldioxid (Heat Transfer and Pressure Drop for Boiling Carbon Dioxide)

    DEFF Research Database (Denmark)

    Knudsen, Hans Jørgen Høgaard

    1999-01-01

    Heat transfer and pressure drop for carbon dioxide, pure and mixed with oil, has the been measured for flow in pipe. The measured heat transfer coefficient for pure carbon dioxide is much higher than the value calculated with the Shah correlation. With oil even higher heat transfer coefficient ha...

  8. Ultrasonic-assisted sol-gel synthesis of samarium, cerium co-doped TiO2 nanoparticles with enhanced sonocatalytic efficiency.

    Science.gov (United States)

    Eskandarloo, Hamed; Badiei, Alireza; Behnajady, Mohammad A; Ziarani, Ghodsi Mohammadi

    2015-09-01

    In this work, pure TiO2 and samarium, cerium mono-doped and co-doped TiO2 catalysts were synthesized by an ultrasonic-assisted sol-gel method and their sonocatalytic efficiency studied toward removal of Methyl Orange as a model organic pollutant from the textile industry. The relationship of structure and sonocatalytic performance of catalysts was established by using various techniques, such as XRD, TEM, SEM, EDX, DRS, and PL. A comparison on the removal efficiency of sonolysis alone and sonocatalytic processes was performed. The results showed that the samarium, cerium co-doped TiO2 catalyst with narrower band gap energy and smaller particle size leads to a rapid removal of pollutant. It was believed that Sm(3+) and Ce(4+) ions can serve as superficial trapping for electrons at conduction band of TiO2 and prolonged the lifetime of electron-hole pairs. Finally, the effect of synthesis and operational variables on the sonocatalytic activity of co-doped TiO2 catalyst was studied and optimized using response surface methodology as a statistical technique. The results showed that the maximum removal efficiency (96.33%) was achieved at the optimum conditions: samarium content of 0.6 wt%, cerium content of 0.82 wt%, initial pollutant concentration of 4.31 mg L(-1), catalyst dosage of 0.84 mg L(-1), ultrasonic irradiation power of 700 W, and irradiation time of 50 min.

  9. Photocatalysis of S-metolachlor in aqueous suspension of magnetic cerium-doped mTiO2 core-shell under simulated solar light.

    Science.gov (United States)

    Mermana, J; Sutthivaiyakit, P; Blaise, C; Gagné, F; Charnsethikul, S; Kidkhunthod, P; Sutthivaiyakit, S

    2017-02-01

    Magnetic cerium-doped mesoporous titanium dioxide was synthesized by combining sol-gel method and calcination using tetrabutanate and ammonium cerium nitrate as precursors and Pluronic P123 as a template coating on iron oxide covered with carbon in ethanol. The magnetic Ce-doped catalyst showed only anatase structure with a slight increase in lattice parameters compared to the undoped catalyst. The Ce LIII-edge X-ray absorption near-edge spectroscopy (XANES) spectra showed Ce(3+), and the cerium substitution doping into titanium dioxide was proposed. Degradation of S-metolachlor in aqueous magnetic photocatalyst suspension followed (pseudo) first-order kinetics in the presence of 0.5 g L(-1) of γ-Fe2O3@C@0.16 mol% Ce-mTiO2 with a half-life of 55.18 ± 1.63 min. Fifteen degradation products were identified, and their transformation routes of the photocatalytic degradation were then proposed. Complementary toxicity assessment of the treated S-metolachlor solution was undertaken with Environment Canada's algal microplate assay measuring growth inhibition (72-h IC50) in the freshwater chlorophyte Pseudokirchneriella subcapitata. This test method revealed a significant decrease in toxicity (1.7-fold reduction after 180 min of irradiation treatment), thereby confirming that the by-products formed following photocatalysis would be less harmful from an environmental point of view. Photocatalytic degradation of S-metolachlor thus appears to hold promise as a cost-effective treatment technology to diminish the presence of this herbicide in aquatic systems.

  10. Purely Functional Structured Programming

    OpenAIRE

    Obua, Steven

    2010-01-01

    The idea of functional programming has played a big role in shaping today's landscape of mainstream programming languages. Another concept that dominates the current programming style is Dijkstra's structured programming. Both concepts have been successfully married, for example in the programming language Scala. This paper proposes how the same can be achieved for structured programming and PURELY functional programming via the notion of LINEAR SCOPE. One advantage of this proposal is that m...

  11. Purely Cortical Anaplastic Ependymoma

    Directory of Open Access Journals (Sweden)

    Flávio Ramalho Romero

    2012-01-01

    Full Text Available Ependymomas are glial tumors derived from ependymal cells lining the ventricles and the central canal of the spinal cord. It may occur outside the ventricular structures, representing the extraventicular form, or without any relationship of ventricular system, called ectopic ependymona. Less than fifteen cases of ectopic ependymomas were reported and less than five were anaplastic. We report a rare case of pure cortical ectopic anaplastic ependymoma.

  12. Carbon dioxide reducing processes; Koldioxidreducerande processer

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Fredrik

    1999-12-01

    This thesis discusses different technologies to reduce or eliminate the carbon dioxide emissions, when a fossil fuel is used for energy production. Emission reduction can be accomplished by separating the carbon dioxide for storage or reuse. There are three different ways of doing the separation. The carbon dioxide can be separated before the combustion, the process can be designed so that the carbon dioxide can be separated without any energy consumption and costly systems or the carbon dioxide can be separated from the flue gas stream. Two different concepts of separating the carbon dioxide from a combined cycle are compared, from the performance and the economical point of view, with a standard natural gas fired combined cycle where no attempts are made to reduce the carbon dioxide emissions. One concept is to use absorption technologies to separate the carbon dioxide from the flue gas stream. The other concept is based on a semi-closed gas turbine cycle using carbon dioxide as working fluid and combustion with pure oxygen, generated in an air-separating unit. The calculations show that the efficiency (power) drop is smaller for the first concept than for the second, 8.7 % points compared to 13.7 % points, when power is produced. When both heat and power are produced, the relation concerning the efficiency (power) remains. Regarding the overall efficiency (heat and power) the opposite relation is present. A possible carbon dioxide tax must exceed 0.21 SEK/kg CO{sub 2} for it to be profitable to separate carbon dioxide with any of these technologies.

  13. Purely tetrahedral quadruple systems

    Institute of Scientific and Technical Information of China (English)

    JI Lijun

    2006-01-01

    An oriented tetrahedron is a set of four vertices and four cyclic triples with the property that any ordered pair of vertices is contained in exactly one of the cyclic triples. A tetrahedral quadruple system of order n (briefly TQS(n)) is a pair (X,B), where X is an nelement set and B is a set of oriented tetrahedra such that every cyclic triple on X is contained in a unique member of B. A TQS(n) (X, B) is pure if there do not exist two oriented tetrahedra with the same vertex set. In this paper, we show that there is a pure TQS(n) if and only if n≡2,4(mod 6),n>4,or n≡1,5(mod 12). One corollary is that there is a simple two-fold quadruple system of order n if and only if n≡2,4 (mod 6) and n>4, or n≡1, 5 (mod 12).Another corollary is that there is an overlarge set of pure Mendelsohn triple systems of order n for n≡1,3(mod 6),n>3, or n≡0,4 (mod 12).

  14. Solubility of cerium in LaCoO3-influence on catalytic activity.

    Science.gov (United States)

    French, S A; Catlow, C R A; Oldman, R J; Rogers, S C; Axon, S A

    2002-11-21

    The recent interest in the catalytic properties of lanthanum perovskites for methane combustion and three way catalysis has led to considerable debate as to their structure and defect chemistry. We have investigated the doping of LaCoO3 with the tetravalent cerium cation using atomistic simulation techniques. We have compared three routes for cerium insertion and identified the favoured doping mechanism, which explain experimental observations relating to the effect of cerium on catalytic activity.

  15. Improvement of cerium of photosynthesis functions of maize under magnesium deficiency.

    Science.gov (United States)

    Zhou, Min; Gong, Xiaolan; Wang, Ying; Liu, Chao; Hong, Mengmeng; Wang, Ling; Hong, Fashui

    2011-09-01

    Rare earth elements can promote photosynthesis, but their mechanisms are still poorly understood under magnesium deficiency. The present study was designed to determine the role of cerium in magnesium-deficient maize plants. Maize was cultivated in Hoagland's solution added with cerium with and without adequate quantities of magnesium. Under magnesium-deficient conditions, cerium can prevents inhibition of synthesis of photosynthetic pigment, improves light energy absorption and conversion, oxygen evolution, and the activity of photo-phosphorelation and its coupling factor Ca(2+)-ATPase. These results suggest that cerium could partly substitute magnesium, improving photosynthesis and plant growth.

  16. The effect of cerium valence states at cerium oxide nanoparticle surfaces on cell proliferation

    KAUST Repository

    Naganuma, Tamaki

    2014-05-01

    Understanding and controlling cell proliferation on biomaterial surfaces is critical for scaffold/artificial-niche design in tissue engineering. The mechanism by which underlying integrin ligates with functionalized biomaterials to induce cell proliferation is still not completely understood. In this study, poly-l-lactide (PL) scaffold surfaces were functionalized using layers of cerium oxide nanoparticles (CNPs), which have recently attracted attention for use in therapeutic application due to their catalytic ability of Ce4+ and Ce3+ sites. To isolate the influence of Ce valance states of CNPs on cell proliferation, human mesenchymal stem cells (hMSCs) and osteoblast-like cells (MG63) were cultured on the PL/CNP surfaces with dominant Ce4+ and Ce3+ regions. Despite cell type (hMSCs and MG63 cells), different surface features of Ce4+ and Ce3+ regions clearly promoted and inhibited cell spreading, migration and adhesion behavior, resulting in rapid and slow cell proliferation, respectively. Cell proliferation results of various modified CNPs with different surface charge and hydrophobicity/hydrophilicity, indicate that Ce valence states closely correlated with the specific cell morphologies and cell-material interactions that trigger cell proliferation. This finding suggests that the cell-material interactions, which influence cell proliferation, may be controlled by introduction of metal elements with different valence states onto the biomaterial surface. © 2014 Elsevier Ltd.

  17. Development and validation of indirect visible spectrophotometric methods for oxcarbazepine in pure and the tablet dosage form

    Directory of Open Access Journals (Sweden)

    Hemavathi N. Deepakumari

    2016-09-01

    Full Text Available Three simple, accurate and highly sensitive indirect spectrophotometric methods have been developed for the determination of oxcarbazepine (OXC in both pure and in pharmaceutical preparations. The methods are based on the oxidation of oxcarbazepine by a known excess of cerium(IV in acid medium. This was followed by the determination of unreacted cerium(IV, which oxidizes leuco dyes to colored dyes in the same acid medium. In method A, an unreacted cerium(IV oxidizes leuco crystal violet to crystal violet dye which is measured at 580 nm. A bluish-colored malachite green with a maximum absorption at 610 nm is developed in method B. In method C, cerium(IV oxidizes leuco xylene cyanol FF to blue colored xylene cyanol FF having absorption maximum at 610 nm. In all these methods, the amount of cerium(IV reacted corresponds to the amount of OXC and the absorbance is found to decrease linearly with OXC concentration. Beer’s law was obeyed in the concentration range of 0–2.5, 0–2.0 and 0–2.5 μg ml−1 for methods A, B and C, respectively, and the corresponding molar absorptivity values are 3.86 × 104, 4.41 × 104 and 2.16 × 104 l mol−1cm−1. All variables have been optimized and the results were statistically compared with those of a literature method by employing the student’s t-test and F-test. No interference was observed from excipients normally added to the tablets.

  18. Adsorption of Fluoride Ion by Inorganic Cerium Based Adsorbent

    Institute of Scientific and Technical Information of China (English)

    Jiao Zhongzhi(焦中志); Chen Zhonglin; Yang Min; Zhang Yu; Li Guibai

    2004-01-01

    Excess of fluoride in drinking water is harmful to human health, the concentration of F- ions must be maintained in the range of 0.5 to 1.5 mg/L. An inorganic cerium based adsorbent (CTA) is developed on the basis of research of adsorption of fluoride on cerium oxide hydrate. Some adsorption of fluoride by CTA adsorbent experiments were carried out, and results showed that CTA adsorbent has a quick adsorption speed and a large adsorption capacity. Adsorption follows Freundlich isotherm, and low pH value helps fluoride removal. Some physical-chemical characteristics of CTA adsorbent were experimented, fluoride removal mechanism was explored, and results showed that hydroxyl group of CTA adsorbent played an important role in the fluoride removal.

  19. Isomorphic phase transformation in shocked Cerium using molecular dynamics

    Directory of Open Access Journals (Sweden)

    Germann T.C.

    2011-01-01

    Full Text Available Cerium (Ce undergoes a significant (∼16% volume collapse associated with an isomorphic fcc-fcc phase transformation when subject to compressive loading. We present here a new Embedded Atom Method (EAM potential for Cerium that models two minima for the two fcc phases. We show results from its use in Molecular Dynamics (MD simulations of Ce samples subjected to shocks with pressures ranging from 0.5 to 25 GPa. A split wave structure is observed, with an elastic precursor followed by a plastic wave. The plastic wave causes the expected fcc-fcc phase transformation. Comparisons to experiments and MD simulations on Cesium (Cs indicate that three waves could be observed. The construction of the EAM potential may be the source of the difference.

  20. Isomorphic phase transformation in shocked cerium using molecular dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Dupont, Virginie [Los Alamos National Laboratory; Germann, Timothy C [Los Alamos National Laboratory; Chen, Shao - Ping [Los Alamos National Laboratory

    2010-08-12

    Cerium (Ce) undergoes a significant ({approx}16%) volume collapse associated with an isomorphic fcc-fcc phase transformation when subject to compressive loading. We present here a new Embedded Atom Method (EAM) potential for Cerium that models two minima for the two fcc phases. We show results from its use in Molecular Dynamics (MD) simulations of Ce samples subjected to shocks with pressures ranging from 0.5 to 25 GPa. A split wave structure is observed, with an elastic precursor followed by a plastic wave. The plastic wave causes the expected fcc-fcc phase transformation. Comparisons to experiments and MD simulations on Cesium (Cs) indicate that three waves could be observed. The construction of the EAM potential may be the source of the difference.

  1. Synthesis and characterization of cerium sulfide thin film

    Institute of Scientific and Technical Information of China (English)

    Ιshak Afsin Kariper

    2014-01-01

    Cerium sulfide (CexSy) polycrystalline thin film is coated with chemical bath deposition on substrates (commercial glass). Transmittance, absorption, optical band gap and refractive index are examined by using UV/VIS. Spectrum. The hexagonal form is observed in the structural properties in XRD. The structural and optical properties of cerium sulfide thin films are analyzed at different pH. SEM and EDX analyses are made for surface analysis and elemental ratio in films. It is observed that some properties of films changed with different pH values. In this study, the focus is on the observed changes in the properties of films. The pH values were scanned at 6–10. The optical band gap changed with pH between 3.40 to 3.60 eV. In addition, the film thickness changed with pH at 411 nm to 880 nm.

  2. PURE DRIVE GT

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    在2004年奥林匹克赛事中,中国的李婷,孙甜甜取得了中国网球第一个金牌一女子双打冠军。忘记不了当时李婷挥动着她的BABOLAT(百保力)网拍Pure Drive Zylon 360°激动地拥抱着孙甜甜吵闹着,幸福地哭着的情景。

  3. Pure de Sitter Supergravity

    CERN Document Server

    Bergshoeff, Eric A; Kallosh, Renata; Van Proeyen, Antoine

    2015-01-01

    Using superconformal methods we derive an explicit de Sitter supergravity action invariant under spontaneously broken local ${\\cal N}=1$ supersymmetry. The supergravity multiplet interacts with a nilpotent goldstino multiplet. We present a complete locally supersymmetric action including the graviton and the fermionic fields, gravitino and goldstino, no scalars. In the global limit when supergravity multiplet decouples, our action reproduces the Volkov-Akulov theory. In the unitary gauge where goldstino vanishes we recover pure supergravity with the positive cosmological constant. The classical equations of motion, with all fermions vanishing, have a maximally symmetric solution: de Sitter space.

  4. Preparation and characterization of gelatin/cerium(Ⅲ) film

    Institute of Scientific and Technical Information of China (English)

    黄崇军; 黄雅钦; 田娜; 童元建; 殷瑞贤

    2010-01-01

    A novel gelatin film with antibacterial activity was prepared by electrostatic crosslinking using cerium (Ⅲ) nitrate hexahydrate as the crosslinking agent. The structure and properties of the films were investigated by Fourier transform infrared spectra, tensile tests, thermogravimetric analysis, static drop contact angle and disc diffusion method. The results showed that cross-linking could not only improve the thermal and mechanical properties and lower the hydrophilic property of the films, but also make...

  5. Cerium chloride reduces enamel lesion initiation and progression in vitro.

    Science.gov (United States)

    Wegehaupt, F J; Buchalla, W; Sener, B; Attin, T; Schmidlin, P R

    2014-01-01

    Determination of the potential of cerium chloride to reduce artificial carious mineral loss and lesion depth progression. A total of 160 enamel samples were prepared from 40 bovine lower central incisors. Crowns were sectioned into four pieces, embedded in acrylic resin, ground flat and allocated to eight groups (S1-S4 and D1-D4; n = 20). Specimens of groups D1-D4 were stored (for 7 days) in a demineralizing buffer solution to induce caries-like lesions. Afterwards, samples were treated for 30 s with one of the following solutions: placebo (S1 and D1), amine fluoride (S2 and D2), cerium chloride (S3 and D3) and a combination of fluoride and cerium chloride (S4 and D4). After another 7 (D1-D4) or 14 (S1-S4) days in demineralizing buffer solution, integrated mineral loss and lesion depth were determined by transversal microradiography and compared by Scheffé's post hoc tests. In groups S1-S4, the highest values for integrated mineral loss and lesion depth were observed for group S1 (placebo), the lowest values for group S4. The results in groups S2-S4 were not significantly different. In groups D1-D4, the highest values for integrated mineral loss and lesion depth were observed for group D1 (placebo), the lowest values in groups D3 and D4. In group D2, integrated mineral loss and lesion depth were significantly lower as compared to D1, but significantly higher compared to groups D3 and D4. Cerium chloride and its combination with fluoride are able to significantly reduce carious mineral loss and the progression of lesion depth.

  6. Jet formation in cerium metal to examine material strength

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, B. J., E-mail: bjjensen@lanl.gov; Cherne, F. J.; Prime, M. B.; Yeager, J. D.; Ramos, K. J.; Hooks, D. E.; Cooley, J. C.; Dimonte, G. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Fezzaa, K. [Argonne National Laboratory, Argonne, Illinois 60439 (United States); Iverson, A. J.; Carlson, C. A. [National Security Technologies LLC, Los Alamos, New Mexico 87544 (United States)

    2015-11-21

    Examining the evolution of material properties at extreme conditions advances our understanding of numerous high-pressure phenomena from natural events like meteorite impacts to general solid mechanics and fluid flow behavior. Recent advances in synchrotron diagnostics coupled with dynamic compression platforms have introduced new possibilities for examining in-situ, spatially resolved material response with nanosecond time resolution. In this work, we examined jet formation from a Richtmyer-Meshkov instability in cerium initially shocked into a transient, high-pressure phase, and then released to a low-pressure, higher-temperature state. Cerium's rich phase diagram allows us to study the yield stress following a shock induced solid-solid phase transition. X-ray imaging was used to obtain images of jet formation and evolution with 2–3 μm spatial resolution. From these images, an analytic method was used to estimate the post-shock yield stress, and these results were compared to continuum calculations that incorporated an experimentally validated equation-of-state (EOS) for cerium coupled with a deviatoric strength model. Reasonable agreement was observed between the calculations and the data illustrating the sensitivity of jet formation on the yield stress values. The data and analysis shown here provide insight into material strength during dynamic loading which is expected to aid in the development of strength aware multi-phase EOS required to predict the response of matter at extreme conditions.

  7. Jet formation in cerium metal to examine material strength

    Science.gov (United States)

    Jensen, B. J.; Cherne, F. J.; Prime, M. B.; Fezzaa, K.; Iverson, A. J.; Carlson, C. A.; Yeager, J. D.; Ramos, K. J.; Hooks, D. E.; Cooley, J. C.; Dimonte, G.

    2015-11-01

    Examining the evolution of material properties at extreme conditions advances our understanding of numerous high-pressure phenomena from natural events like meteorite impacts to general solid mechanics and fluid flow behavior. Recent advances in synchrotron diagnostics coupled with dynamic compression platforms have introduced new possibilities for examining in-situ, spatially resolved material response with nanosecond time resolution. In this work, we examined jet formation from a Richtmyer-Meshkov instability in cerium initially shocked into a transient, high-pressure phase, and then released to a low-pressure, higher-temperature state. Cerium's rich phase diagram allows us to study the yield stress following a shock induced solid-solid phase transition. X-ray imaging was used to obtain images of jet formation and evolution with 2-3 μm spatial resolution. From these images, an analytic method was used to estimate the post-shock yield stress, and these results were compared to continuum calculations that incorporated an experimentally validated equation-of-state (EOS) for cerium coupled with a deviatoric strength model. Reasonable agreement was observed between the calculations and the data illustrating the sensitivity of jet formation on the yield stress values. The data and analysis shown here provide insight into material strength during dynamic loading which is expected to aid in the development of strength aware multi-phase EOS required to predict the response of matter at extreme conditions.

  8. Antibacterial activity of polymer coated cerium oxide nanoparticles.

    Directory of Open Access Journals (Sweden)

    Vishal Shah

    Full Text Available Cerium oxide nanoparticles have found numerous applications in the biomedical industry due to their strong antioxidant properties. In the current study, we report the influence of nine different physical and chemical parameters: pH, aeration and, concentrations of MgSO(4, CaCl(2, KCl, natural organic matter, fructose, nanoparticles and Escherichia coli, on the antibacterial activity of dextran coated cerium oxide nanoparticles. A least-squares quadratic regression model was developed to understand the collective influence of the tested parameters on the anti-bacterial activity and subsequently a computer-based, interactive visualization tool was developed. The visualization allows us to elucidate the effect of each of the parameters in combination with other parameters, on the antibacterial activity of nanoparticles. The results indicate that the toxicity of CeO(2 NPs depend on the physical and chemical environment; and in a majority of the possible combinations of the nine parameters, non-lethal to the bacteria. In fact, the cerium oxide nanoparticles can decrease the anti-bacterial activity exerted by magnesium and potassium salts.

  9. Study of tetravalent cerium incorporation in the monazite structure

    Energy Technology Data Exchange (ETDEWEB)

    Bregiroux, D.; Audubert, F.; Bernache-Assollant, D

    2004-07-01

    The incorporation of tetravalent cerium in the monazite structure (La{sub 1-2x}Ce{sup 4+}{sub x}Ca{sub x}PO{sub 4}) by high temperature solid state synthesis was investigated. First of all, the reaction was followed by DTA-TGA method and X-rays diffraction. It has been shown that CaO first reacts with the phosphate precursor to form Ca(PO{sub 3}){sub 2}. This compound melts near 940 deg C, inducing the dissociation of CeO{sub 2} and the reduction of a large part of cerium IV to cerium III. Two methods have been developed to determine the Ce{sup 4+}/Ce{sup 3+} ratio by using X-ray diffraction and microprobe analysis. We show that Ce{sup 4+} incorporation in LaPO{sub 4} is limited to a Ce{sup 4+}/Ce{sup 3+} = 0.15 value. (authors)

  10. pH-distribution of cerium species in aqueous systems

    Institute of Scientific and Technical Information of China (English)

    B.Bouchaud; J.Balmain; G.Bonnet; F.Pedraza

    2012-01-01

    Cerium-based oxide coalings can be obtained through either chemical or electrochemical processes on various conductor and semiconductor substrates.In both cases the films develop through a precipitation mechanism,which strongly depends on the solution chemistry.In the particular case of the electrolytic approach,the elaboration parameters play a key role on the interfacial pH modification thereby leading to an indirect precipitation mechanism.Indeed,the nucleation and growth mechanisms of crystallites and the composition of the resulting layers have been shown to be also strongly affected by the deposition conditions as well as by the substrate composition,which could in turn modify the protectiveness provided by such coatings.Therefore a better fundamental understanding of the system is required,in particular of the distribution of cerium-containing species in aqueous solution.To this end,the present work intended to develop a diagram showing the distribution as well as the relative amount of Ce(Ⅲ)/Ce(Ⅳ) species in aqueous media as a function of the pH range.The resulting pH-distribution diagram turned out to be a useful tool to predict the relevant precipitation mechanisms and species involved during the growth of cerium-containing films and to draw correlations with the characteristics of the as-deposited films.

  11. Cadmium Telluride-Titanium Dioxide Nanocomposite for Photodegradation of Organic Substance.

    Science.gov (United States)

    Ontam, Areeporn; Khaorapapong, Nithima; Ogawa, Makoto

    2015-12-01

    Cadmium telluride-titanium dioxide nanocomposite was prepared by hydrothermal reaction of sol-gel derived titanium dioxide and organically modified cadmium telluride. The crystallinity of titanium dioxide in the nanocomposite was higher than that of pure titanium dioxide obtained by the reaction under the same temperature and pressure conditions, showing that cadmium telluride induced the crystallization of titanium dioxide. Diffuse reflectance spectrum of the nanocomposite showed the higher absorption efficiency in the UV-visible region due to band-gap excitation of titanium dioxide. The nanocomposite significantly showed the improvement of photocatalytic activity for 4-chlorophenol with UV light.

  12. Effect of cerium dioxide, titanium dioxide, silver, and gold nanoparticles on the activity of microbial communities intended in wastewater treatment

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, Ana; Delgado, Lucia; Tora, Josep A. [Department of Chemical Engineering, Escola d' Enginyeria, Universitat Autonoma de Barcelona, 08193 Bellaterra (Spain); Casals, Eudald; Gonzalez, Edgar [Institut Catala de Nanotecnologia, Campus de la Universitat Autonoma de Barcelona, 08193 Bellaterra (Spain); Puntes, Victor [Institut Catala de Nanotecnologia, Campus de la Universitat Autonoma de Barcelona, 08193 Bellaterra (Spain); Institut Catala de Recerca i Estudis Avancats, Passeig Lluis Companys, 23, 08010 Barcelona (Spain); Font, Xavier; Carrera, Julian [Department of Chemical Engineering, Escola d' Enginyeria, Universitat Autonoma de Barcelona, 08193 Bellaterra (Spain); Sanchez, Antoni, E-mail: antoni.sanchez@uab.cat [Department of Chemical Engineering, Escola d' Enginyeria, Universitat Autonoma de Barcelona, 08193 Bellaterra (Spain)

    2012-01-15

    Highlights: Black-Right-Pointing-Pointer Toxicity of TiO{sub 2}, CeO{sub 2}, Ag and Au nanoparticles (NP) has been studied. Black-Right-Pointing-Pointer NP were synthesized in the lab and stabilized to prevent agglomeration. Black-Right-Pointing-Pointer Toxicity was studied in all the communities used for the wastewater treatment. Black-Right-Pointing-Pointer Heterotrophic, nitrifying and anaerobic organisms were studied for nanotoxicology. Black-Right-Pointing-Pointer Au and TiO{sub 2} NP were not toxic, but Ag and CeO{sub 2} NP were inhibitory. - Abstract: Growth in production and use of nanoparticles (NPs) will result increased concentrations of these in industrial and urban wastewaters and, consequently, in wastewater-treatment facilities. The effect of this increase on the performance of the wastewater-treatment process has not been studied systematically and including all the microbial communities involved in wastewater treatment. The present work investigates, by using respiration tests and biogas-production analysis, the inhibitory effect of four different commonly used metal oxide (CeO{sub 2} and TiO{sub 2}) and zero-valent metal (Ag and Au) nanoparticles on the activity of the most important microbial communities present in a modern wastewater-treatment plant. Specifically, the actions of ordinary heterotrophic organisms, ammonia oxidizing bacteria, and thermophilic and mesophilic anaerobic bacteria were tested in the presence and absence of the nanoparticles. In general, CeO{sub 2} nanoparticles caused the greatest inhibition in biogas production (nearly 100%) and a strong inhibitory action of other biomasses; Ag nanoparticles caused an intermediate inhibition in biogas production (within 33-50%) and a slight inhibition in the action of other biomasses, and Au and TiO{sub 2} nanoparticles caused only slight or no inhibition for all tested biomasses.

  13. Induction of pulmonary fibrosis by cerium oxide nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Jane Y., E-mail: jym1@cdc.gov [Health Effects Laboratory Division, National Institute for Occupational Safety and Health, Morgantown, WV 26505 (United States); Mercer, Robert R.; Barger, Mark; Schwegler-Berry, Diane; Scabilloni, James [Health Effects Laboratory Division, National Institute for Occupational Safety and Health, Morgantown, WV 26505 (United States); Ma, Joseph K. [School of Pharmacy, West Virginia University, Morgantown, WV 26506 (United States); Castranova, Vincent [Health Effects Laboratory Division, National Institute for Occupational Safety and Health, Morgantown, WV 26505 (United States)

    2012-08-01

    Cerium compounds have been used as a diesel engine catalyst to lower the mass of diesel exhaust particles, but are emitted as cerium oxide (CeO{sub 2}) nanoparticles in the diesel exhaust. In a previous study, we have demonstrated a wide range of CeO{sub 2}-induced lung responses including sustained pulmonary inflammation and cellular signaling that could lead to pulmonary fibrosis. In this study, we investigated the fibrogenic responses induced by CeO{sub 2} in a rat model at various time points up to 84 days post-exposure. Male Sprague Dawley rats were exposed to CeO{sub 2} by a single intratracheal instillation. Alveolar macrophages (AM) were isolated by bronchial alveolar lavage (BAL). AM-mediated cellular responses, osteopontin (OPN) and transform growth factor (TGF)-β1 in the fibrotic process were investigated. The results showed that CeO{sub 2} exposure significantly increased fibrotic cytokine TGF-β1 and OPN production by AM above controls. The collagen degradation enzymes, matrix metalloproteinase (MMP)-2 and -9 and the tissue inhibitor of MMP were markedly increased in the BAL fluid at 1 day- and subsequently declined at 28 days after exposure, but remained much higher than the controls. CeO{sub 2} induced elevated phospholipids in BAL fluid and increased hydroxyproline content in lung tissue in a dose- and time-dependent manner. Immunohistochemical analysis showed MMP-2, MMP-9 and MMP-10 expressions in fibrotic regions. Morphological analysis noted increased collagen fibers in the lungs exposed to a single dose of 3.5 mg/kg CeO{sub 2} and euthanized at 28 days post-exposure. Collectively, our studies show that CeO{sub 2} induced fibrotic lung injury in rats, suggesting it may cause potential health effects. -- Highlights: ► Cerium oxide exposure significantly affected the following parameters in the lung. ► Induced fibrotic cytokine OPN and TGF-β1 production and phospholipidosis. ► Caused imbalance of the MMP-9/ TIMP-1 ratio that favors fibrosis

  14. LUMINESCENT PROPERTIES OF SILICATE GLASSES WITH CERIUM IONS AND ANTIMONY

    Directory of Open Access Journals (Sweden)

    A. M. Klykova

    2014-05-01

    Full Text Available The paper deals with the results of an experimental study of luminescence excitation spectra and luminescence of silicate glasses containing cerium ions and antimony. The aim of this work was to study the features of the luminescence and the effect of UV irradiation and heat treatment on luminescence and the state of cerium ions and antimony in glass. We investigated glass system Na2O-ZnO-Al2O3-SiO2-NaF-NaBr with additives CeO2 and Sb2O3. Synthesis was carried out in platinum crucibles in the air at 14500C. The samples were polished glass plates with a thickness of 0.5-1 mm. UV irradiation was carried out with a mercury lamp having a wide range of radiation in the spectral range 240-390 nm. It was conducted in a Nabertherm muffle furnaces. Luminescence spectra and excitation spectra were measured using a spectrofluorimeter MPF-44A (PerkinElmer at the room temperature. Measured luminescence spectra were corrected in view of the spectral sensitivity of the photodetector for spectrofluorimeter. Adjustment of the excitation spectra for the spectral dependence of the intensity of the excitation source was not carried out. During the experiments it was found that in silicate glasses Sb3+ ions can exist in two energy states, which corresponds to a different environment with oxygen ions. Heat treatment of these glasses in an oxidizing atmosphere leads to an increase in ion concentration of Sb3+ ions with a greater amount of oxygen in the environment. In glasses containing antimony and cerium ions, ultraviolet irradiation causes a change in the valence of cerium ions and antimony, which is accompanied by luminescence quenching. Subsequent heat treatment of glass leads to the inverse processes and restore luminescence excitation spectra. The study of fluorescent properties of silicate glasses with cerium and antimony ions led to the conclusion of the practical significance of this work. Promising multifunctional materials can be created on the basis of

  15. Single crystal to single crystal transformation and hydrogen-atom transfer upon oxidation of a cerium coordination compound.

    Science.gov (United States)

    Williams, Ursula J; Mahoney, Brian D; Lewis, Andrew J; DeGregorio, Patrick T; Carroll, Patrick J; Schelter, Eric J

    2013-04-15

    Trivalent and tetravalent cerium compounds of the octamethyltetraazaannulene (H2omtaa) ligand have been synthesized. Electrochemical analysis shows a strong thermodynamic preference for the formal cerium(IV) oxidation state. Oxidation of the cerium(III) congener Ce(Homtaa)(omtaa) occurs by hydrogen-atom transfer that includes a single crystal to single crystal transformation upon exposure to an ambient atmosphere.

  16. Pure laparoscopic augmentation ileocystoplasty.

    Science.gov (United States)

    Rebouças, Rafael B; Monteiro, Rodrigo C; Souza, Thiago N S de; Aragão, Augusto J de; Burity, Camila R T; Nóbrega, Júlio C de A; Oliveira, Natália S C de; Abrantes, Ramon B; Dantas Júnior, Luiz B; Cartaxo Filho, Ricardo; Negromonte, Gustavo R P; Sampaio, Rafael da C R; Britto, Cesar A

    2014-01-01

    Guillain-Barre syndrome is an acute neuropathy that rarely compromises bladder function. Conservative management including clean intermittent catheterization and pharmacotherapy is the primary approach for hypocompliant contracted bladder. Surgical treatment may be used in refractory cases to improve bladder compliance and capacity in order to protect the upper urinary tract. We describe a case of pure laparoscopic augmentation ileocystoplasty in a patient affected by Guillain-Barre syndrome. A 15-year-old female, complaining of voiding dysfunction, recurrent urinary tract infection and worsening renal function for three months. A previous history of Guillain-Barre syndrome on childhood was related. A voiding cystourethrography showed a pine-cone bladder with moderate post-void residual urine. The urodynamic demonstrated a hypocompliant bladder and small bladder capacity (190 mL) with high detrusor pressure (54 cmH2O). Nonsurgical treatments were attempted, however unsuccessfully.

  17. Pure Parsimony Xor Haplotyping

    CERN Document Server

    Bonizzoni, Paola; Dondi, Riccardo; Pirola, Yuri; Rizzi, Romeo

    2010-01-01

    The haplotype resolution from xor-genotype data has been recently formulated as a new model for genetic studies. The xor-genotype data is a cheaply obtainable type of data distinguishing heterozygous from homozygous sites without identifying the homozygous alleles. In this paper we propose a formulation based on a well-known model used in haplotype inference: pure parsimony. We exhibit exact solutions of the problem by providing polynomial time algorithms for some restricted cases and a fixed-parameter algorithm for the general case. These results are based on some interesting combinatorial properties of a graph representation of the solutions. Furthermore, we show that the problem has a polynomial time k-approximation, where k is the maximum number of xor-genotypes containing a given SNP. Finally, we propose a heuristic and produce an experimental analysis showing that it scales to real-world large instances taken from the HapMap project.

  18. Pure parsimony xor haplotyping.

    Science.gov (United States)

    Bonizzoni, Paola; Della Vedova, Gianluca; Dondi, Riccardo; Pirola, Yuri; Rizzi, Romeo

    2010-01-01

    The haplotype resolution from xor-genotype data has been recently formulated as a new model for genetic studies. The xor-genotype data is a cheaply obtainable type of data distinguishing heterozygous from homozygous sites without identifying the homozygous alleles. In this paper, we propose a formulation based on a well-known model used in haplotype inference: pure parsimony. We exhibit exact solutions of the problem by providing polynomial time algorithms for some restricted cases and a fixed-parameter algorithm for the general case. These results are based on some interesting combinatorial properties of a graph representation of the solutions. Furthermore, we show that the problem has a polynomial time k-approximation, where k is the maximum number of xor-genotypes containing a given single nucleotide polymorphisms (SNP). Finally, we propose a heuristic and produce an experimental analysis showing that it scales to real-world large instances taken from the HapMap project.

  19. Toxicity assessment of Titanium Dioxide and Cerium Oxide nanoparticles in Arabidopsis thaliana L.

    Science.gov (United States)

    The production and applications of nanoparticles (NP) in diverse fields has steadily increased in recent decades; however, knowledge about risks of NP to human health and ecosystems is still scarce. In this study, we assessed potential toxicity of two commercially used engineere...

  20. Synthesis of Cerium Dioxide High-k Thin Films as a Gate Dielectric in MOS Capacitor

    Directory of Open Access Journals (Sweden)

    Anil G. Khairnar

    2013-07-01

    Full Text Available In the present study, the Al/CeO2 / p-Si MOS capacitor was fabricated by depositing the Aluminium (Al metal layer by thermal evaporation technique on sol-gel derived CeO2 high-k thin films on p-Si substrate. The deposited CeO2 films were characterized by Ellipsometer to study the refractive index that is determined to be 3.62. The FTIR analysis was carried out to obtain chemical bonding characteristics. Capacitance-voltage measurements of Al/CeO2 /p-Si MOS capacitor were carried out to determine the dielectric constant, equivalent oxide thickness (EOT and flat band shift (VFB for the deposited CeO2 film of 16.22, 1.62 nm and 0.7 V respectively. The conductance voltage curve was used to determine the interface trap density (Dit at the CeO2 / p-Si interface that is calculated to be 1.29 × 1013 cm – 2 eV – 1 for measurement frequency of 500 kHz.

  1. Effect of natural organic matter on cerium dioxide nanoparticles settling in model fresh water

    NARCIS (Netherlands)

    Quik, J.T.K.; Lynch, I.; Hoecke, van K.; Miermans, C.J.H.; Schamphelaere, de K.A.C.; Janssen, C.R.; Dawson, K.A.; Cohen Stuart, M.A.; Meent, van de D.

    2010-01-01

    The ecological risk assessment of chemicals including nanoparticles is based on the determination of adverse effects on organisms and on the environmental concentrations to which biota are exposed. The aim of this work was to better understand the behavior of nanoparticles in the environment, with t

  2. Existence of three-phase interlines on a cerium dioxide surface

    CERN Document Server

    Osarinmwian, Charles

    2013-01-01

    The three-phase interline described by a statistical continuum limit (i.e. quasi-boundary) has been postulated to gain a deeper insight into the reduction of CeO2 to CeO1.940 in a LiCl-KCl eutectic melt. Fabrication of a CeO2 superstructure by a condensed-phase method provided a CeO2 (111) surface at the nanoscale, which allowed the three-phase interline to be identified given previously reported quantum confinement effects in quasi-stoichiometric CeO2 nanoparticles. Also, the CeO2 superstructure displays the same crystal lattice planes as a bulk CeO2 grain but the triply degenerate Raman-active peak of the grain is higher by a factor of ~ 2.5 with a wider full width at half maximum.

  3. Exposure to Cerium Dioxide Nanoparticles Differently Affect Swimming Performance and Survival in Two Daphnid Species

    Science.gov (United States)

    Artells, Ester; Issartel, Julien; Auffan, Mélanie; Borschneck, Daniel; Thill, Antoine; Tella, Marie; Brousset, Lenka; Rose, Jérôme; Bottero, Jean-Yves; Thiéry, Alain

    2013-01-01

    The CeO2 NPs are increasingly used in industry but the environmental release of these NPs and their subsequent behavior and biological effects are currently unclear. This study evaluates for the first time the effects of CeO2 NPs on the survival and the swimming performance of two cladoceran species, Daphnia similis and Daphnia pulex after 1, 10 and 100 mg.L−1 CeO2 exposures for 48 h. Acute toxicity bioassays were performed to determine EC50 of exposed daphnids. Video-recorded swimming behavior of both daphnids was used to measure swimming speeds after various exposures to aggregated CeO2 NPs. The acute ecotoxicity showed that D. similis is 350 times more sensitive to CeO2 NPs than D. pulex, showing 48-h EC50 of 0.26 mg.L−1 and 91.79 mg.L−1, respectively. Both species interacted with CeO2 NPs (adsorption), but much more strongly in the case of D. similis. Swimming velocities (SV) were differently and significantly affected by CeO2 NPs for both species. A 48-h exposure to 1 mg.L−1 induced a decrease of 30% and 40% of the SV in D. pulex and D. similis, respectively. However at higher concentrations, the SV of D. similis was more impacted (60% off for 10 mg.L−1 and 100 mg.L−1) than the one of D. pulex. These interspecific toxic effects of CeO2 NPs are explained by morphological variations such as the presence of reliefs on the cuticle and a longer distal spine in D. similis acting as traps for the CeO2 aggregates. In addition, D. similis has a mean SV double that of D. pulex and thus initially collides with twice more NPs aggregates. The ecotoxicological consequences on the behavior and physiology of a CeO2 NPs exposure in daphnids are discussed. PMID:23977004

  4. Cerium dioxide and zinc oxide nanoparticles alter the nutritional value of soil cultivated soybean plants.

    Science.gov (United States)

    Peralta-Videa, Jose R; Hernandez-Viezcas, Jose A; Zhao, Lijuan; Diaz, Baltazar Corral; Ge, Yuan; Priester, John H; Holden, Patricia Ann; Gardea-Torresdey, Jorge L

    2014-07-01

    The aim of this study was to determine nutrient elements in soybean (Glycine max) plants cultivated in farm soil amended with nCeO2 at 0-1000 mg kg(-1) and nZnO at 0-500 mg kg(-1). Digested samples were analyzed by ICP-OES/MS. Compared to control, pods from nCeO2 at 1000 mg kg(-1) had significantly less Ca but more P and Cu, while pods from 100 mg kg(-1)nZnO had more Zn, Mn, and Cu. Plants treated with nZnO showed significant correlations among Zn, P, and S in pods with Zn in roots. Correlations among pod Zn/root Zn was r = 0.808 (p ≤ 0.01) and pod P/root P was r = 0.541 (p ≤ 0.05). The correlation among pod S/root S was r = -0.65 (p ≤ 0.01). While nCeO2 treatments exhibited significant correlations between pod Ca/root Ca (r = 0.645, p ≤ 0.05). The data suggest that nCeO2 and nZnO alter the nutritional value of soybean, which could affect the health of plants, humans, and animals.

  5. Direct growth of cerium oxide nanorods on diverse substrates for superhydrophobicity and corrosion resistance

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Young Jun; Jang, Hanmin; Lee, Kwan-Soo [School of Mechanical Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Kim, Dong Rip, E-mail: dongrip@hanyang.ac.kr [School of Mechanical Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Institute of Nano Science and Technology, Hanyang University, Seoul 133-791 (Korea, Republic of)

    2015-06-15

    Graphical abstract: - Highlights: • Cerium oxide nanorods were uniformly grown on diverse substrates. • Changes in growth conditions led to morphology evolution of cerium oxide nanostructures. • The grown cerium oxide nanostructures were single or poly crystalline. • Direct growth of cerium oxide nanorods made the diverse substrates superhydrophobic and anti-corrosive without any surface modifiers. - Abstract: Superhydrophobic surfaces with anti-corrosion properties have attracted great interest in many industrial fields, particularly to enhance the thermal performance of offshore applications such as heat exchangers, pipelines, power plants, and platform structures. Nanostructures with hydrophobic materials have been widely utilized to realize superhydrophobicity of surfaces, and cerium oxide has been highlighted due to its good corrosion resistive and intrinsically hydrophobic properties. However, few studies of direct growth of cerium oxide nanostructures on diverse substrates have been reported. Herein we report a facile hydrothermal method to directly grow cerium oxide nanorods on diverse substrates, such as aluminum alloy, stainless steel, titanium, and silicon. Diverse substrates with cerium oxide nanorods exhibited superhydrophobicity with no hydrophobic modifiers on their surfaces, and showed good corrosion resistive properties in corrosive medium. We believe our method could pave the way for realization of scalable and sustainable corrosion resistive superhydrophobic surfaces in many industrial fields.

  6. Cerium doped red mud catalytic ozonation for bezafibrate degradation in wastewater: Efficiency, intermediates, and toxicity.

    Science.gov (United States)

    Xu, Bingbing; Qi, Fei; Sun, Dezhi; Chen, Zhonglin; Robert, Didier

    2016-03-01

    In this study, the performance of bezafibrate (BZF) degradation and detoxification in the aqueous phase using cerium-modified red mud (RM) catalysts prepared using different cerium sources and synthesis methods were evaluated. Experimental results showed that the surface cerium modification was responsible for the development of the catalytic activity of RM and this was influenced by the cerium source and the synthesis method. Catalyst prepared from cerium (IV) by precipitation was found to show the best catalytic activity in BZF degradation and detoxification. Reactive oxygen species including peroxides, hydroxyl radicals, and super oxide ions were identified in all reactions and we proposed the corresponding catalytic reaction mechanism for each catalyst that prepared from different cerium source and method. This was supported by the intermediates profiles that were generated upon BZF degradation. The surface and the structural properties of cerium-modified RM were characterized in detail by several analytical methods. Two interesting findings were made: (1) the surface texture (specific surface area and mesoporous volume) influenced the catalytic reaction pathway; and (2) Ce(III) species and oxygen vacancies were generated on the surface of the catalyst after cerium modification. This plays an important role in the development of the catalytic activity.

  7. Carbon dioxide capture and use: organic synthesis using carbon dioxide from exhaust gas.

    Science.gov (United States)

    Kim, Seung Hyo; Kim, Kwang Hee; Hong, Soon Hyeok

    2014-01-13

    A carbon capture and use (CCU) strategy was applied to organic synthesis. Carbon dioxide (CO2) captured directly from exhaust gas was used for organic transformations as efficiently as hyper-pure CO2 gas from a commercial source, even for highly air- and moisture-sensitive reactions. The CO2 capturing aqueous ethanolamine solution could be recycled continuously without any diminished reaction efficiency.

  8. Spectrophotometric determination of H 2-receptor antagonists via their oxidation with cerium(IV)

    Science.gov (United States)

    Darwish, Ibrahim A.; Hussein, Samiha A.; Mahmoud, Ashraf M.; Hassan, Ahmed I.

    2008-01-01

    A simple, accurate and sensitive spectrophotometric method has been developed and validated for determination of H 2-receptor antagonists: cimetidine, famotidine, nizatidine and ranitidine hydrochloride. The method was based on the oxidation of these drugs with cerium(IV) in presence of perchloric acid and subsequent measurement of the excess Ce(IV) by its reaction with p-dimethylaminobenzaldehyde to give a red colored product ( λmax at 464 nm). The decrease in the absorption intensity of the colored product (Δ A), due to the presence of the drug was correlated with its concentration in the sample solution. Different variables affecting the reaction were carefully studied and optimized. Under the optimum conditions, linear relationships with good correlation coefficients (0.9990-0.9994) were found between Δ A values and the concentrations of the drugs in a concentration range of 1-20 μg ml -1. The assay limits of detection and quantitation were 0.18-0.60 and 0.54-1.53 μg ml -1, respectively. The method was validated, in terms of accuracy, precision, ruggedness and robustness; the results were satisfactory. The proposed method was successfully applied to the determination of the investigated drugs in pure and pharmaceutical dosage forms (recovery was 98.3-102.6 ± 0.57-1.90%) without interference from the common excipients. The results obtained by the proposed method were comparable with those obtained by the official methods.

  9. Spectrophotometric determination of H(2)-receptor antagonists via their oxidation with cerium(IV).

    Science.gov (United States)

    Darwish, Ibrahim A; Hussein, Samiha A; Mahmoud, Ashraf M; Hassan, Ahmed I

    2008-01-01

    A simple, accurate and sensitive spectrophotometric method has been developed and validated for determination of H(2)-receptor antagonists: cimetidine, famotidine, nizatidine and ranitidine hydrochloride. The method was based on the oxidation of these drugs with cerium(IV) in presence of perchloric acid and subsequent measurement of the excess Ce(IV) by its reaction with p-dimethylaminobenzaldehyde to give a red colored product (lambda(max) at 464nm). The decrease in the absorption intensity of the colored product (DeltaA), due to the presence of the drug was correlated with its concentration in the sample solution. Different variables affecting the reaction were carefully studied and optimized. Under the optimum conditions, linear relationships with good correlation coefficients (0.9990-0.9994) were found between DeltaA values and the concentrations of the drugs in a concentration range of 1-20microgml(-1). The assay limits of detection and quantitation were 0.18-0.60 and 0.54-1.53microgml(-1), respectively. The method was validated, in terms of accuracy, precision, ruggedness and robustness; the results were satisfactory. The proposed method was successfully applied to the determination of the investigated drugs in pure and pharmaceutical dosage forms (recovery was 98.3-102.6+/-0.57-1.90%) without interference from the common excipients. The results obtained by the proposed method were comparable with those obtained by the official methods.

  10. Cerium oxide nanoparticles/multi-wall carbon nanotubes composites: Facile synthesis and electrochemical performances as supercapacitor electrode materials

    Science.gov (United States)

    Deng, Dongyang; Chen, Nan; Li, Yuxiu; Xing, Xinxin; Liu, Xu; Xiao, Xuechun; Wang, Yude

    2017-02-01

    Cerium oxide nanoparticles/multi-wall carbon nanotubes (MWCNTs) composites are synthesized by a facile hydrothermal method without any surfactant or template. The morphology and microstructure of samples are examined by scanning electron microscopy (SEM), transition electron microscopy (TEM), X-ray diffraction (XRD), Raman spectrum and X-ray photoelectron spectroscopy (XPS). Electrochemical properties of the MWCNTs, the pure CeO2, and the CeO2/MWCNTs nanocomposites electrodes are investigated by cyclic voltammetry (CV), galvanostatic charge/discharge (GDC) and electrochemical impedance spectroscopy (EIS) measurements. The CeO2/MWCNTs nanocomposite (at the mole ratio of 1:1) electrode exhibits much larger specific capacitance compared with both the MWCNTs electrode and the pure CeO2 electrode and significantly improves cycling stability compared to the pure CeO2 electrode. The CeO2/MWCNTs nanocomposite (at the mole ratio of 1:1) achieves a specific capacitance of 455.6 F g-1 at the current density of 1 A g-1. Therefore, the as prepared CeO2/MWCNTs nanocomposite is a promising electrode material for high-performance supercapacitors.

  11. Tuning Reactivity and Electronic Properties through Ligand Reorganization within a Cerium Heterobimetallic Framework

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, Jerome R.; Gordon, Zachary; Booth, Corwin H.; Carroll, Patrick J.; Walsh, Patrick J.; Schelter, Eric J.

    2014-06-24

    Cerium compounds have played vital roles in organic, inorganic, and materials chemistry due to their reversible redox chemistry between trivalent and tetravalent oxidation states. However, attempts to rationally access molecular cerium complexes in both oxidation states have been frustrated by unpredictable reactivity in cerium(III) oxidation chemistry. Such oxidation reactions are limited by steric saturation at the metal ion, which can result in high energy activation barriers for electron transfer. An alternative approach has been realized using a rare earth/alkali metal/1,1'-BINOLate (REMB) heterobimetallic framework, which uses redox-inactive metals within the secondary coordination sphere to control ligand reorganization. The rational syntheses of functionalized cerium(IV) products and a mechanistic examination of the role of ligand reorganization in cerium(III) oxidation are presented.

  12. Pure Laparoscopic Augmentation Ileocystoplasty

    Directory of Open Access Journals (Sweden)

    Rafael B. Rebouças

    2014-12-01

    Full Text Available Introduction Guillain-Barre syndrome is an acute neuropathy that rarely compromises bladder function. Conservative management including clean intermittent catheterization and pharmacotherapy is the primary approach for hypocompliant contracted bladder. Surgical treatment may be used in refractory cases to improve bladder compliance and capacity in order to protect the upper urinary tract. We describe a case of pure laparoscopic augmentation ileocystoplasty in a patient affected by Guillain-Barre syndrome. Presentation A 15-year-old female, complaining of voiding dysfunction, recurrent urinary tract infection and worsening renal function for three months. A previous history of Guillain-Barre syndrome on childhood was related. A voiding cystourethrography showed a pine-cone bladder with moderate post-void residual urine. The urodynamic demonstrated a hypocompliant bladder and small bladder capacity (190mL with high detrusor pressure (54 cmH2O. Nonsurgical treatments were attempted, however unsuccessfully. The patient was placed in the exaggerated Trendelenburg position. A four-port transperitoneal technique was used. A segment of ileum approximately 15-20cm was selected and divided with its pedicle. The ileal anastomosis and creation of ileal U-shaped plate were performed laparoscopically, without staplers. Bladder mobilization and longidutinal cystotomy were performed. Enterovesical anastomosis was done with continuous running suture. A suprapubic cystostomy was placed through a 5mm trocar. Results The total operative time was 335 min. The blood loss was minimal. The patient developed ileus in the early days, diet acceptance after the fourth day and was discharged on the seventh postoperative day. The urethral catheter was removed after 2 weeks. At 6-month follow-up, a cystogram showed a significant improvement in bladder capacity. The patient adhered well to clean intermittent self-catheterization and there was no report for febrile infections

  13. Synthesis and characterization of uranium (IV) phosphate-hydrogenphosphate hydrate and cerium (IV) phosphate-hydrogenphosphate hydrate

    Science.gov (United States)

    Brandel, V.; Clavier, N.; Dacheux, N.

    2005-04-01

    A new uranium (IV) phosphate of proposed formula U 2(PO 4) 2HPO 4·H 2O, i.e. uranium phosphate-hydrogenphosphate hydrate (UPHPH), was synthesized in autoclave and/or in polytetrafluoroethylene closed containers at 150 °C by three ways: from uranium (IV) hydrochloric solution and phosphoric acid, from uranium dioxide and phosphoric acid and by transformation of the uranium hydrogenphosphate hydrate U(HPO 4) 2· nH 2O. The new product appears similar to the previously published thorium phosphate-hydrogenphosphate hydrate Th 2(PO 4) 2HPO 4·H 2O (TPHPH). From preliminary studies, it was found that UPHPH crystallizes in monoclinic system ( a=2.1148(7) nm, b=0.6611(2) nm, c=0.6990(3) nm, β=91.67(3)° and V=0.9768(10) nm). Heated under inert atmosphere, this compound is decomposed above 400 °C into uranium phosphate-triphosphate U 2(PO 4)P 3O 10, uranium diphosphate α-UP 2O 7 and diuranium oxide phosphate U 2O(PO 4) 2. Crystallized cerium (IV) phosphate-hydrogenphosphate hydrate Ce 2(PO 4) 2HPO 4·H 2O (CePHPH) was also synthesized from (NH 4) 2Ce(NO 3) 6 and phosphoric acid solutions by the same method (monoclinic system: a=2.1045(5) nm, b=0.6561(2) nm, c=0.6949(2) nm, β=91.98(1)° and V=0.9588(9) nm). When heating above 600 °C, cerium (IV) is reduced into Ce (III) and forms a mixture of CePO 4 (monazite structure) and CeP 3O 9.

  14. Effects of uncoated and citric acid coated cerium oxide nanoparticles, bulk cerium oxide, cerium acetate, and citric acid on tomato plants.

    Science.gov (United States)

    Barrios, Ana Cecilia; Rico, Cyren M; Trujillo-Reyes, Jesica; Medina-Velo, Illya A; Peralta-Videa, Jose R; Gardea-Torresdey, Jorge L

    2016-09-01

    Little is known about the physiological and biochemical responses of plants exposed to surface modified nanomaterials. In this study, tomato (Solanum lycopersicum L.) plants were cultivated for 210days in potting soil amended with uncoated and citric acid coated cerium oxide nanoparticles (nCeO2, CA+nCeO2) bulk cerium oxide (bCeO2), and cerium acetate (CeAc). Millipore water (MPW), and citric acid (CA) were used as controls. Physiological and biochemical parameters were measured. At 500mg/kg, both the uncoated and CA+nCeO2 increased shoot length by ~9 and ~13%, respectively, while bCeO2 and CeAc decreased shoot length by ~48 and ~26%, respectively, compared with MPW (p≤0.05). Total chlorophyll, chlo-a, and chlo-b were significantly increased by CA+nCeO2 at 250mg/kg, but reduced by bCeO2 at 62.5mg/kg, compared with MPW. At 250 and 500mg/kg, nCeO2 increased Ce in roots by 10 and 7 times, compared to CA+nCeO2, but none of the treatments affected the Ce concentration in above ground tissues. Neither nCeO2 nor CA+nCeO2 affected the homeostasis of nutrient elements in roots, stems, and leaves or catalase and ascorbate peroxidase in leaves. CeAc at 62.5 and 125mg/kg increased B (81%) and Fe (174%) in roots, while at 250 and 500mg/kg, increased Ca in stems (84% and 86%, respectively). On the other hand, bCeO2 at 62.5 increased Zn (152%) but reduced P (80%) in stems. Only nCeO2 at 62.5mg/kg produced higher total number of tomatoes, compared with control and the rest of the treatments. The surface coating reduced Ce uptake by roots but did not affect its translocation to the aboveground organs. In addition, there was no clear effect of surface coating on fruit production. To our knowledge, this is the first study comparing the effects of coated and uncoated nCeO2 on tomato plants. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Spectrophotometric determination of cerium with methylthymol blue in the presence of oxalate and cyanide as masking agents

    Energy Technology Data Exchange (ETDEWEB)

    Cabrera-Martin, A.; Izquierdo-Hornillos, R.; Quejido-Cabezas, A.J.; Peral-Fernandez, J.L. (Universidad Complutense de Madrid (Spain). Facultad de Ciencias Quimicas)

    1983-04-01

    The spectrophotometric determination of cerium can be carried out by several methods, which involve either the formation of complexes of cerium(III) and cerium(IV) or the oxidation of suitable reagents by cerium(IV) and further measuring the intensity of the colour of the oxidised matter. The latter methods show a lack of selectivity and low sensitivity owing to the nature of the redox reaction. The methods that involve the formation of complexes have also been shown to have low selectivity and sensitivity. However, the most useful methods are those based on the complexes of cerium(III) with Xylenol Orange and Methylthymol Blue (MTB), but they are affected by many interferences. In this work the reaction of cerium(III) with MTB in the presence of oxalate and cyanide ions was studied at pH 10.2, which improves the sensitivity and the selectivity of the determination of cerium.

  16. Electrochemical studies on cerium(Ⅲ) in molten fluoride mixtures

    Institute of Scientific and Technical Information of China (English)

    VIRGIL; CONSTANTIN; ANA-MARIA; POPESCU; MIRCEA; OLTEANU

    2010-01-01

    This study aims to determine the principal electrochemical characteristics of the electrodeposition of cerium metal from molten fluoride systems.The cathodic process of Ce3+ ions in LiF-NaF and LiF-NaF-CaF2 molten salts was studied using electrochemical techniques as steady state and cyclic voltammetry methods.The decomposition potential(Ed) and the overvoltage(η) were determined for NaCeF4 using current-potential curves under galvanostatic conditions.The Ed was found to be 2.025 V in LiF-NaF and 2.045 V in...

  17. Identification of the Charge Carriers in Cerium Phosphate Ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Ray, Hannah L.; Jonghe, Lutgard C. De

    2010-06-02

    The total conductivity of Sr-doped cerium orthophosphate changes by nearly two orders of magnitude depending on the oxygen and hydrogen content of the atmosphere. The defect model for the system suggests that this is because the identity of the dominant charge carrier can change from electron holes to protons when the sample is in equilibrium with air vs. humidified hydrogen. In this work are presented some preliminary measurements that can help to clarify this exchange between carriers. The conduction behavior of a 2percent Sr-doped CePO4 sample under symmetric atmospheric conditions is investigated using several techniques, including AC impedance, H/D isotope effects, and chronoamperometry.

  18. Cerium oxide based nanometric powders: synthesis and characterization

    Directory of Open Access Journals (Sweden)

    Ninić M.

    2007-01-01

    Full Text Available Nanometric powders of solid solutions of cerium oxide were obtained by a modified glycine nitrate procedure. Solid solutions of the host compound CeO2 with one or more dopants in the lattice were synthesized. Rare earth cations (Re=Yb, Gd and Sm were added to ceria in total concentration of x= 0.2 that was kept constant. The criterion in doping was to keep the value of lattice parameter of ceria unchanged. The lattice parameters were calculated by using the model that takes into account the existence of oxygen vacancies in the structure.

  19. Options for the recovery of cerium by solvent extraction

    Energy Technology Data Exchange (ETDEWEB)

    Soldenhoff, K.H. [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia)

    1996-12-31

    This paper reports the results of an experimental program to examine the use of various commercial reagents for the extraction of cerium (IV) from sulphate solutions. Extractants tested include organophosphorus esters (TOPO, Cyanex 923 and Cyanex 925), organophosphorus acids (DEHPA, lonquest 801 and Cyanex 272) and high molecular weight amine, Alamine 336. The suitability of reagents is assessed in terms of process relevant criteria such as extraction dependence on acidity, selectivity over other rare earths and thorium, stability of reagent towards oxidation and loading characteristics. (author) 15 refs., 2 tabs., 5 figs.

  20. Properties of hot liquid cerium by LDA + U molecular dynamics.

    Science.gov (United States)

    Siberchicot, Bruno; Clérouin, Jean

    2012-11-14

    We present ab initio simulations of liquid cerium in the framework of the LDA + U formulation. The liquid density has been determined self-consistently by searching for the zero pressure equilibrium state at 1320 K with the same set of parameters (U and J) and occupation matrices as those optimized for the γ phase. We have computed static and transport properties. The liquid produced by the simulations appears more structured than the available measurements. This raises questions regarding the ability of the theory to describe such a complex liquid. Conductivity calculations and temperature dependences are nevertheless in reasonable agreement with data.

  1. Freshwater dispersion stability of PAA-stabilised cerium oxide nanoparticles and toxicity towards Pseudokirchneriella subcapitata

    Energy Technology Data Exchange (ETDEWEB)

    Booth, Andy, E-mail: andy.booth@sintef.no [SINTEF Materials and Chemistry, Trondheim N-7465 (Norway); Størseth, Trond [SINTEF Materials and Chemistry, Trondheim N-7465 (Norway); Altin, Dag [BioTrix, Trondheim N-7022 (Norway); Fornara, Andrea; Ahniyaz, Anwar [German Federal Institute for Risk Assessment (BfR), Department of Product Safety, Berlin (Germany); Jungnickel, Harald; Laux, Peter; Luch, Andreas [SP Chemistry, Materials and Surfaces, Drottning Kristinas vag 45, SE-11686 Stockholm (Sweden); Sørensen, Lisbet [SINTEF Materials and Chemistry, Trondheim N-7465 (Norway)

    2015-02-01

    An aqueous dispersion of poly (acrylic acid)-stabilised cerium oxide (CeO{sub 2}) nanoparticles (PAA-CeO{sub 2}) was evaluated for its stability in a range of freshwater ecotoxicity media (MHRW, TG 201 and M7), with and without natural organic matter (NOM). In a 15 day dispersion stability study, PAA-CeO{sub 2} did not undergo significant aggregation in any media type. Zeta potential varied between media types and was influenced by PAA-CeO{sub 2} concentration, but remained constant over 15 days. NOM had no influence on PAA-CeO{sub 2} aggregation or zeta potential. The ecotoxicity of the PAA-CeO{sub 2} dispersion was investigated in 72 h algal growth inhibition tests using the freshwater microalgae Pseudokirchneriella subcapitata. PAA-CeO{sub 2} EC{sub 50} values for growth inhibition (GI; 0.024 mg/L) were 2–3 orders of magnitude lower than pristine CeO{sub 2} EC{sub 50} values reported in the literature. The concentration of dissolved cerium (Ce{sup 3+}/Ce{sup 4+}) in PAA-CeO{sub 2} exposure suspensions was very low, ranging between 0.5 and 5.6 μg/L. Free PAA concentration in the exposure solutions (0.0096–0.0384 mg/L) was significantly lower than the EC{sub 10} growth inhibition (47.7 mg/L) value of pure PAA, indicating that free PAA did not contribute to the observed toxicity. Elemental analysis indicated that up to 38% of the total Cerium becomes directly associated with the algal cells during the 72 h exposure. TOF-SIMS analysis of algal cell wall compounds indicated three different modes of action, including a significant oxidative stress response to PAA-CeO{sub 2} exposure. In contrast to pristine CeO{sub 2} nanoparticles, which rapidly aggregate in standard ecotoxicity media, PAA-stabilised CeO{sub 2} nanoparticles remain dispersed and available to water column species. Interaction of PAA with cell wall components, which could be responsible for the observed biomarker alterations, could not be excluded. This study indicates that the increased

  2. Soil organic matter influences cerium translocation and physiological processes in kidney bean plants exposed to cerium oxide nanoparticles.

    Science.gov (United States)

    Majumdar, Sanghamitra; Peralta-Videa, Jose R; Trujillo-Reyes, Jesica; Sun, Youping; Barrios, Ana C; Niu, Genhua; Margez, Juan P Flores-; Gardea-Torresdey, Jorge L

    2016-11-01

    Soil organic matter plays a major role in determining the fate of the engineered nanomaterials (ENMs) in the soil matrix and effects on the residing plants. In this study, kidney bean plants were grown in soils varying in organic matter content and amended with 0-500mg/kg cerium oxide nanoparticles (nano-CeO2) under greenhouse condition. After 52days of exposure, cerium accumulation in tissues, plant growth and physiological parameters including photosynthetic pigments (chlorophylls and carotenoids), net photosynthesis rate, transpiration rate, and stomatal conductance were recorded. Additionally, catalase and ascorbate peroxidase activities were measured to evaluate oxidative stress in the tissues. The translocation factor of cerium in the nano-CeO2 exposed plants grown in organic matter enriched soil (OMES) was twice as the plants grown in low organic matter soil (LOMS). Although the leaf cover area increased by 65-111% with increasing nano-CeO2 concentration in LOMS, the effect on the physiological processes were inconsequential. In OMES leaves, exposure to 62.5-250mg/kg nano-CeO2 led to an enhancement in the transpiration rate and stomatal conductance, but to a simultaneous decrease in carotenoid contents by 25-28%. Chlorophyll a in the OMES leaves also decreased by 27 and 18% on exposure to 125 and 250mg/kg nano-CeO2. In addition, catalase activity increased in LOMS stems, and ascorbate peroxidase increased in OMES leaves of nano-CeO2 exposed plants, with respect to control. Thus, this study provides clear evidence that the properties of the complex soil matrix play decisive roles in determining the fate, bioavailability, and biological transport of ENMs in the environment. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Novel borothermal route for the synthesis of lanthanum cerium hexaborides and their field emission properties

    Energy Technology Data Exchange (ETDEWEB)

    Menaka [Department of Chemistry, Indian Institute of Technology, Hauz Khas, New Delhi-110016 (India); Patra, Rajkumar; Ghosh, Santanu [Department of Physics, Indian Institute of Technology, Hauz Khas, New Delhi-110016 (India); Ganguli, Ashok K., E-mail: ashok@chemistry.iitd.ac.in [Department of Chemistry, Indian Institute of Technology, Hauz Khas, New Delhi-110016 (India)

    2012-10-15

    The present study describes the development of a simple approach to stabilize polycrystalline lanthanum cerium hexaborides without using any flux and at ambient pressure. The nanostructured lanthanum-cerium borides were synthesized using hydroxide precursors. These precursors (La{sub 1-x}Ce{sub x}(OH){sub 3}, x=0.1, 0.2, 0.3 and 0.5) were synthesized via hydrothermal route in the presence of Tergitol (surfactant, nonylphenol ethoxylate) as a capping agent. The precursors on heating with boron at 1300 Degree-Sign C lead to the formation of nanostructures (cubes, rods and pyramids) of lanthanum cerium hexaboride. We have investigated the field emission behaviour of the hexaboride films fabricated by spin coating. It was observed that the pyramidal shaped nanostructures of La{sub 0.5}Ce{sub 0.5}B{sub 6} shows excellent field emission characteristics with high field enhancement factor of 4502. - Graphical abstract: Nanostructured lanthanum cerium hexaboride with efficient field emission have fabricated by low temperature hydroxide precursor mediated route. Highlights: Black-Right-Pointing-Pointer New methodology to prepare lanthanum cerium hexaboride at 1300 Degree-Sign C via borothermal route. Black-Right-Pointing-Pointer Nanostructured lanthanum cerium hexaboride film by spin coating process. Black-Right-Pointing-Pointer Nanopyramids based lanthanum cerium hexaboride shows excellent field emission.

  4. Hydrothermal synthesis of cerium titanate nanorods and its application in visible light photocatalysis

    Energy Technology Data Exchange (ETDEWEB)

    Pei, L.Z., E-mail: lzpei@ahut.edu.cn; Liu, H.D.; Lin, N.; Yu, H.Y., E-mail: yuhy@ahut.edu.cn

    2015-01-15

    Highlights: • Cerium titanate nanorods have been synthesized by a simple hydrothermal process. • The size of the cerium titanate nanorods can be controlled by growth conditions. • Cerium titanate nanorods exhibit good photocatalytic activities for methyl blue. - Abstract: Cerium titanate nanorods have been prepared via a hydrothermal process using sodium dodecyl sulfate (SDS) as the surfactant. The cerium titanate nanorods have been analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), and ultraviolet–visible (UV–vis) diffuse reflectance spectrum. XRD shows that the nanorods are composed of CeTi{sub 21}O{sub 38} phase. Electron microscopy observations indicate that the nanorods have good single crystalline nature. The diameter and length of the nanorods are about 50–200 nm and 1–2 μm, respectively. Cerium titanate nanorods have a band gap of 2.65 eV. The photocatalytic activities of the nanorods have been investigated by degrading methylene blue (MB) under visible light irradiation. MB solution with the concentration of 10 mg L{sup −1} can be degraded totally with the irradiation time increasing to 240 min. Cerium titanate nanorods exhibit great potential in photocatalytic degradation of MB under visible light irradiation.

  5. Pulmonary toxicity of well-dispersed cerium oxide nanoparticles following intratracheal instillation and inhalation

    Energy Technology Data Exchange (ETDEWEB)

    Morimoto, Yasuo, E-mail: yasuom@med.uoeh-u.ac.jp; Izumi, Hiroto; Yoshiura, Yukiko; Tomonaga, Taisuke; Oyabu, Takako; Myojo, Toshihiko; Kawai, Kazuaki; Yatera, Kazuhiro [University of Occupational and Environmental Health (Japan); Shimada, Manabu; Kubo, Masaru [Hiroshima University (Japan); Yamamoto, Kazuhiro [National Institute of Advanced Industrial Science and Technology (AIST) (Japan); Kitajima, Shinichi [National Sanatorium Hoshizuka Keiaien (Japan); Kuroda, Etsushi [Osaka University, Laboratory of Vaccine Science, WPI Immunology Frontier Research Center (Japan); Kawaguchi, Kenji; Sasaki, Takeshi [National Institute of Advanced Industrial Science and Technology (AIST) (Japan)

    2015-11-15

    We performed inhalation and intratracheal instillation studies of cerium dioxide (CeO{sub 2}) nanoparticles in order to investigate their pulmonary toxicity, and observed pulmonary inflammation not only in the acute and but also in the chronic phases. In the intratracheal instillation study, F344 rats were exposed to 0.2 mg or 1 mg of CeO{sub 2} nanoparticles. Cell analysis and chemokines in bronchoalveolar lavage fluid (BALF) were analyzed from 3 days to 6 months following the instillation. In the inhalation study, rats were exposed to the maximum concentration of inhaled CeO{sub 2} nanoparticles (2, 10 mg/m{sup 3}, respectively) for 4 weeks (6 h/day, 5 days/week). The same endpoints as in the intratracheal instillation study were examined from 3 days to 3 months after the end of the exposure. The intratracheal instillation of CeO{sub 2} nanoparticles caused a persistent increase in the total and neutrophil number in BALF and in the concentration of cytokine-induced neutrophil chemoattractant (CINC)-1, CINC-2, chemokine for neutrophil, and heme oxygenase-1 (HO-1), an oxidative stress marker, in BALF during the observation time. The inhalation of CeO{sub 2} nanoparticles also induced a persistent influx of neutrophils and expression of CINC-1, CINC-2, and HO-1 in BALF. Pathological features revealed that inflammatory cells, including macrophages and neutrophils, invaded the alveolar space in both studies. Taken together, the CeO{sub 2} nanoparticles induced not only acute but also chronic inflammation in the lung, suggesting that CeO{sub 2} nanoparticles have a pulmonary toxicity that can lead to irreversible lesions.

  6. Altering properties of cerium oxide thin films by Rh doping

    Energy Technology Data Exchange (ETDEWEB)

    Ševčíková, Klára, E-mail: klarak.sevcikova@seznam.cz [Faculty of Mathematics and Physics, Department of Surface and Plasma Science, Charles University in Prague, V Holešovičkách 2, 180 00 Prague 8 (Czech Republic); NIMS Beamline Station at SPring-8, National Institute for Materials Science, Sayo, Hyogo 679-5148 (Japan); Nehasil, Václav, E-mail: nehasil@mbox.troja.mff.cuni.cz [Faculty of Mathematics and Physics, Department of Surface and Plasma Science, Charles University in Prague, V Holešovičkách 2, 180 00 Prague 8 (Czech Republic); Vorokhta, Mykhailo, E-mail: vorohtam@gmail.com [Faculty of Mathematics and Physics, Department of Surface and Plasma Science, Charles University in Prague, V Holešovičkách 2, 180 00 Prague 8 (Czech Republic); Haviar, Stanislav, E-mail: stanislav.haviar@gmail.com [Faculty of Mathematics and Physics, Department of Surface and Plasma Science, Charles University in Prague, V Holešovičkách 2, 180 00 Prague 8 (Czech Republic); Matolín, Vladimír, E-mail: matolin@mbox.troja.mff.cuni.cz [Faculty of Mathematics and Physics, Department of Surface and Plasma Science, Charles University in Prague, V Holešovičkách 2, 180 00 Prague 8 (Czech Republic); and others

    2015-07-15

    Highlights: • Thin films of ceria doped by rhodium deposited by RF magnetron sputtering. • Concentration of rhodium has great impact on properties of Rh–CeO{sub x} thin films. • Intensive oxygen migration in films with low concentration of rhodium. • Oxygen migration suppressed in films with high amount of Rh dopants. - Abstract: Ceria containing highly dispersed ions of rhodium is a promising material for catalytic applications. The Rh–CeO{sub x} thin films with different concentrations of rhodium were deposited by RF magnetron sputtering and were studied by soft and hard X-ray photoelectron spectroscopies, Temperature programmed reaction and X-ray powder diffraction techniques. The sputtered films consist of rhodium–cerium mixed oxide where cerium exhibits a mixed valency of Ce{sup 4+} and Ce{sup 3+} and rhodium occurs in two oxidation states, Rh{sup 3+} and Rh{sup n+}. We show that the concentration of rhodium has a great influence on the chemical composition, structure and reducibility of the Rh–CeO{sub x} thin films. The films with low concentrations of rhodium are polycrystalline, while the films with higher amount of Rh dopants are amorphous. The morphology of the films strongly influences the mobility of oxygen in the material. Therefore, varying the concentration of rhodium in Rh–CeO{sub x} thin films leads to preparing materials with different properties.

  7. Functionalization of nanostructured cerium oxide films with histidine.

    Science.gov (United States)

    Tsud, Nataliya; Bercha, Sofiia; Acres, Robert G; Vorokhta, Mykhailo; Khalakhan, Ivan; Prince, Kevin C; Matolín, Vladimír

    2015-01-28

    The surfaces of polycrystalline cerium oxide films were modified by histidine adsorption under vacuum and characterized by the synchrotron based techniques of core and valence level photoemission, resonant photoemission and near edge X-ray absorption spectroscopy, as well as atomic force microscopy. Histidine is strongly bound to the oxide surface in the anionic form through the deprotonated carboxylate group, and forms a disordered molecular adlayer. The imidazole ring and the amino side group do not form bonds with the substrate but are involved in the intermolecular hydrogen bonding which stabilizes the molecular adlayer. The surface reaction with histidine results in water desorption accompanied by oxide reduction, which is propagated into the bulk of the film. Previously studied, well-characterized surfaces are a guide to the chemistry of the present polycrystalline surface and histidine bonds via the carboxylate group in both cases. In contrast, bonding via the imidazole group occurs on the well-ordered surface but not in the present case. The morphology and structure of the cerium oxide are decisive factors which define the adsorption geometry of the histidine adlayer.

  8. Interactional effect of cerium and manganese on NO catalytic oxidation.

    Science.gov (United States)

    Liang, Yanli; Huang, Yufen; Zhang, Hailong; Lan, Li; Zhao, Ming; Gong, Maochu; Chen, Yaoqiang; Wang, Jianli

    2017-04-01

    To preferably catalyze the oxidation of NO to NO2 in diesel after-treatment system, a series of CeO2-MnO x composite oxides was supported on silica-alumina material by the co-impregnation method. The maximum conversion of NO of the catalyst with a Ce/Mn weight ratio of 5:5 was improved by around 40%, compared to the supported manganese-only or cerium-only sample. And its maximum reaction rate was 0.056 μmol g(-1) s(-1) at 250 °C at the gas hourly space velocity of 30,000 h(-1). The experimental results suggested that Ce-Mn solid solution was formed, which could modulate the valence state of cerium and manganese and exhibit great redox properties. Moreover, the strong interaction between ceria and manganese resulted in the largest desorption amount of strong chemical oxygen and oxygen vacancies, leading to the maximum O α area ratio of 62.26% from the O 1s result. These effective oxygen species could be continually transferred to the surface, leading to the best NO catalytic activity of 5Ce5Mn/SA catalyst. Graphical abstract.

  9. Cerium Tetrafluoride: Sublimation, Thermolysis, and Atomic Fluorine Migration.

    Science.gov (United States)

    Chilingarov, N S; Knot'ko, A V; Shlyapnikov, I M; Mazej, Z; Kristl, M; Sidorov, L N

    2015-08-06

    Saturated vapor pressure p° and enthalpy of sublimation (ΔsH°) of cerium tetrafluoride CeF4 were determined by means of Knudsen effusion mass spectrometry in the range of 750-920 K. It was discovered that sublimation of cerium tetrafluoride from a platinum effusion cell competes with thermal decomposition to CeF3 in the solid phase, but no accompanying release of fluorine to the gas phase occurs. Thus, fluorine atoms migrate within the surface layer of CeF4(s) to the regions of their irreversible drain. We used scanning electron microscopy to study the distribution of the residual CeF3(s) across the inner surface of the effusion cell after complete evaporation of CeF4(s). It was observed that CeF3 accumulates near the edge of the effusion orifice and near the junction of the lid and the body of the cell, that is, in those regions where the fluorine atoms can migrate to a free platinum surface and thus be depleted from the system. Distribution of CeF3(s) solid particles indicates the ways of fluorine atoms migration providing CeF3(s) formation inside the CeF4(s) surface layer.

  10. Biosorption potential of cerium ions usingSpirulina biomass

    Institute of Scientific and Technical Information of China (English)

    David Sadovsky; Asher Brenner; Boaz Astrachan; Boaz Asaf; Raphael Gonen

    2016-01-01

    Two types of cyanobacteria of the genusArthrospira (commonly known asSpirulina) were tested for biosorption of ce-rium(III) ions from aqueous solutions. An endemic type (ES) found in the northern Negev desert, Israel, and a commercial powder (CS) were used in this study. Biosorption was evaluated as a function of pH, contact time, initial metal concentration, number of sorp-tion-desorption cycles, and salt concentration. The optimum pH range for biosorption was found to be 5.0–5.5. The kinetic character-istics of bothSpirulina types were found to be highly compatible with a pseudo-second order kinetic model. The adsorption isotherms of both types were found to be well-suited to Langmuir and Freundlich adsorption isotherms. Maximum biosorption uptakes, accord-ing to the Langmuir model, were 18.1 and 38.2 mg/g, for ES and CS, respectively. Sodium chloride concentrations of up to 5 g/L had a minor effect on cerium biosorption. Desorption efficiency was found to be greater than 97% with 0.1 mol/L HNO3 after three sorp-tion-desorption cycles, without significant loss in the biosorption capacity. The results indicated the feasibility of cerium recovery from industrial wastes usingSpirulina biomass.

  11. Cerium fluoride nanoparticles protect cells against oxidative stress

    Energy Technology Data Exchange (ETDEWEB)

    Shcherbakov, Alexander B.; Zholobak, Nadezhda M. [Zabolotny Institute of Microbiology and Virology, National Academy of Sciences of Ukraine, Kyiv D0368 (Ukraine); Baranchikov, Alexander E. [Kurnakov Institute of General and Inorganic Chemistry of the Russian Academy of Sciences, Moscow 119991 (Russian Federation); Ryabova, Anastasia V. [Prokhorov General Physics Institute of the Russian Academy of Sciences, Moscow 119991 (Russian Federation); National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Moscow 115409 (Russian Federation); Ivanov, Vladimir K., E-mail: van@igic.ras.ru [Kurnakov Institute of General and Inorganic Chemistry of the Russian Academy of Sciences, Moscow 119991 (Russian Federation); National Research Tomsk State University, Tomsk 634050 (Russian Federation)

    2015-05-01

    A novel facile method of non-doped and fluorescent terbium-doped cerium fluoride stable aqueous sols synthesis is proposed. Intense green luminescence of CeF{sub 3}:Tb nanoparticles can be used to visualize these nanoparticles' accumulation in cells using confocal laser scanning microscopy. Cerium fluoride nanoparticles are shown for the first time to protect both organic molecules and living cells from the oxidative action of hydrogen peroxide. Both non-doped and terbium-doped CeF{sub 3} nanoparticles are shown to provide noteworthy protection to cells against the vesicular stomatitis virus. - Highlights: • Facile method of CeF{sub 3} and CeF{sub 3}:Tb stable aqueous sols synthesis is proposed. • Naked CeF{sub 3} nanoparticles are shown to be non-toxic and to protect cells from the action of H{sub 2}O{sub 2}. • CeF{sub 3} and CeF{sub 3}:Tb nanoparticles are shown to protect living cells against the vesicular stomatitis virus.

  12. Visual processing in pure alexia

    DEFF Research Database (Denmark)

    Starrfelt, Randi; Habekost, Thomas; Gerlach, Christian

    2010-01-01

    Whether pure alexia is a selective disorder that affects reading only, or if it reflects a more general visual disturbance, is highly debated. We have investigated the selectivity of visual deficits in a pure alexic patient (NN) using a combination of psychophysical measures, mathematical modelling...

  13. Structural, topographical and electrical properties of cerium doped strontium barium niobate (Ce:SBN60) ceramics

    Science.gov (United States)

    Raj, S. Gokul; Mathivanan, V.; Kumar, G. Ramesh; Yathavan, S.; Mohan, R.

    2016-05-01

    Tungsten bronze type cerium doped strontium barium niobate (Ce:SBN - Sr0.6B0.4Nb2O6) ceramics were synthesized by solid state process. Cerium was used as dopant to improve its electrical properties. Influence of Ce+ ions on the photoluminescence properties was investigated in detail. The grain size topographical behavior of SBN powders and their associated abnormal grain growth (AGG) were completely analyzed through SEM studies. Finally dielectric, measurement discusses about the broad phase transition observed due to cerium dopant The results were discussed in detail.

  14. Structural, topographical and electrical properties of cerium doped strontium barium niobate (Ce:SBN60) ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Raj, S. Gokul [Department of Physics, C. Kandaswami Naidu College For Men (CKNC), Annanagar, Chennai-600102 (India); Mathivanan, V.; Mohan, R. [Department of Physics, Presidency College, Chennai – 600005 (India); Kumar, G. Ramesh, E-mail: rameshvandhai@gmail.com; Yathavan, S. [Department of Physics, University College of Engineering Arni, Anna University Chennai, Arni-632317 (India)

    2016-05-06

    Tungsten bronze type cerium doped strontium barium niobate (Ce:SBN - Sr{sub 0.6}B{sub 0.4}Nb{sub 2}O{sub 6}) ceramics were synthesized by solid state process. Cerium was used as dopant to improve its electrical properties. Influence of Ce{sup +} ions on the photoluminescence properties was investigated in detail. The grain size topographical behavior of SBN powders and their associated abnormal grain growth (AGG) were completely analyzed through SEM studies. Finally dielectric, measurement discusses about the broad phase transition observed due to cerium dopant The results were discussed in detail.

  15. Titrimetric and Spectrophotometric Methods for the Assay of Ketotifen Using Cerium(IV) and Two Reagents

    OpenAIRE

    Madihalli Srinivas Raghu; Kanakapura Basavaiah; Kudige Nagaraj Prashanth; Kanakapura Basavaiah Vinay

    2013-01-01

    One titrimetric and two spectrophotometric methods are described for the determination of ketotifen fumarate (KTF) in bulk drug and in tablets using cerium(IV) as the oxidimetric agent. In titrimetry (method A), the drug was treated with a measured excess of cerium(IV) in H2SO4 medium and after a standing time of 10 min, the surplus oxidant was determined by back titration with iron(II). The spectrophotometric procedures involve addition of a known excess of cerium(IV) to KTF in acid medium f...

  16. Removal of fluoride from fluoride-bering cerium sulfate solution by hydrous zirconium oxide

    Directory of Open Access Journals (Sweden)

    J. G. He

    2014-04-01

    Full Text Available In this paper the removal of fluoride from fluoride-bearing cerium sulfate solution by amorphous hydrous zirconium oxide was studied. The FTIR, SEM, EDS and UV-vis spectra show that fluoride is successfully adsorbed on hydrous zirconium oxide, and cerium exists as Ce4+ in solution. The study indicates that it is feasible to separate fluorine and cerium from fluorine-bearing rare earth sulfate solution using hydrous zirconium oxide, and eliminate the influence of fluoride on the extraction separation of rare earths.

  17. Magnetophotonic crystal with cerium substituted yttrium iron garnet and enhanced Faraday rotation angle.

    Science.gov (United States)

    Yoshimoto, Takuya; Goto, Taichi; Isogai, Ryosuke; Nakamura, Yuichi; Takagi, Hiroyuki; Ross, C A; Inoue, M

    2016-04-18

    Magnetophotonic crystals (MPCs) comprising cerium-substituted yttrium iron garnet (CeYIG) sandwiched by two Bragg mirrors were fabricated by vacuum annealing. CeYIG was deposited on Bragg mirrors at room temperature and annealed in 5 Pa of residual air. No ceria or other non-garnet phases were detected. Cerium 3 + ions substituted on the yttrium sites and no cerium 4 + ions were found. The Faraday rotation angle of the MPC was -2.92° at a wavelength of λ = 1570 nm was 30 times larger than that of the CeYIG film. These results showed good agreement with calculated values derived using a matrix approach.

  18. Manganese-cerium oxide catalysts prepared by non-thermal plasma for NO oxidation: Effect of O2 in discharge atmosphere

    Science.gov (United States)

    Liu, Lu; Zheng, Chenghang; Wu, Shenghao; Gao, Xiang; Ni, Mingjiang; Cen, Kefa

    2017-09-01

    Non-thermal plasma with different O2 concentration in discharge atmosphere was applied to synthesize manganese and cerium mixed-oxides catalysts, which were compared in NO oxidation activity. Discharge atmosphere displayed a crucial influence on the performance of the catalysts prepared by plasma. Relatively low O2 concentration in discharge atmosphere allows synthesizing manganese-cerium oxides catalysts in a moderate environment and therefore is favorable for better physicochemical properties which lead to superior catalytic behavior. The best catalyst was obtained by treatment with 10% O2/N2 plasma and presented over 80% NO conversion in the temperature range of 275-325 °C, whereas catalyst prepared in pure O2 discharge atmosphere had the same activity with a catalyst prepared by calcinations. A correlation between the surface properties of the plasma prepared catalysts and its catalytic activity in NO oxidation is proposed. The amount of the surface adsorbed oxygen has an obvious linear correlation with the amount of Ce3+, the H2 consumption at low temperatures and the catalytic performance. The superior catalytic performance is mainly attributed to the stronger interaction between manganese oxides and ceria, and the formation of poorly crystallized Mn-O-Ce phase in the catalyst which resulted from the slow decomposition of nitrates and organics during plasma treatment. Catalysts prepared in relatively low O2 concentration have large specific surface area and is abundant in Ce3+ species and active oxygen species. The study suggests that plasma treatment with proper discharge gas components is a promising method to prepare effective manganese- cerium oxides catalyst for NO oxidation.

  19. Effects of uncoated and citric acid coated cerium oxide nanoparticles, bulk cerium oxide, cerium acetate, and citric acid on tomato plants

    Energy Technology Data Exchange (ETDEWEB)

    Barrios, Ana Cecilia [Department of Chemistry, The University of Texas at El Paso, 500 W. University Avenue, El Paso, TX 79968 (United States); Rico, Cyren M. [Department of Chemistry, The University of Texas at El Paso, 500 W. University Avenue, El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN), The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); Trujillo-Reyes, Jesica [Department of Chemistry, The University of Texas at El Paso, 500 W. University Avenue, El Paso, TX 79968 (United States); Medina-Velo, Illya A. [Department of Chemistry, The University of Texas at El Paso, 500 W. University Avenue, El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN), The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); Peralta-Videa, Jose R. [Department of Chemistry, The University of Texas at El Paso, 500 W. University Avenue, El Paso, TX 79968 (United States); Environmental Science and Engineering Ph.D. Program, The University of Texas at El Paso, 500 W. University Avenue, El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN), The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); Gardea-Torresdey, Jorge L., E-mail: jgardea@utep.edu [Department of Chemistry, The University of Texas at El Paso, 500 W. University Avenue, El Paso, TX 79968 (United States); Environmental Science and Engineering Ph.D. Program, The University of Texas at El Paso, 500 W. University Avenue, El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN), The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States)

    2016-09-01

    Little is known about the physiological and biochemical responses of plants exposed to surface modified nanomaterials. In this study, tomato (Solanum lycopersicum L.) plants were cultivated for 210 days in potting soil amended with uncoated and citric acid coated cerium oxide nanoparticles (nCeO{sub 2}, CA + nCeO{sub 2}) bulk cerium oxide (bCeO{sub 2}), and cerium acetate (CeAc). Millipore water (MPW), and citric acid (CA) were used as controls. Physiological and biochemical parameters were measured. At 500 mg/kg, both the uncoated and CA + nCeO{sub 2} increased shoot length by ~ 9 and ~ 13%, respectively, while bCeO{sub 2} and CeAc decreased shoot length by ~ 48 and ~ 26%, respectively, compared with MPW (p ≤ 0.05). Total chlorophyll, chlo-a, and chlo-b were significantly increased by CA + nCeO{sub 2} at 250 mg/kg, but reduced by bCeO{sub 2} at 62.5 mg/kg, compared with MPW. At 250 and 500 mg/kg, nCeO{sub 2} increased Ce in roots by 10 and 7 times, compared to CA + nCeO{sub 2}, but none of the treatments affected the Ce concentration in above ground tissues. Neither nCeO{sub 2} nor CA + nCeO{sub 2} affected the homeostasis of nutrient elements in roots, stems, and leaves or catalase and ascorbate peroxidase in leaves. CeAc at 62.5 and 125 mg/kg increased B (81%) and Fe (174%) in roots, while at 250 and 500 mg/kg, increased Ca in stems (84% and 86%, respectively). On the other hand, bCeO{sub 2} at 62.5 increased Zn (152%) but reduced P (80%) in stems. Only nCeO{sub 2} at 62.5 mg/kg produced higher total number of tomatoes, compared with control and the rest of the treatments. The surface coating reduced Ce uptake by roots but did not affect its translocation to the aboveground organs. In addition, there was no clear effect of surface coating on fruit production. To our knowledge, this is the first study comparing the effects of coated and uncoated nCeO{sub 2} on tomato plants. - Highlights: • At 500 mg/kg, coated and bare NPs increased stem length by 13 and 9

  20. New doped tin dioxide electrodes for electrochemical ozone generation

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Y.H.; Li, G.; Liang, Y.R.; Nie, Z.Z.; Chen, Q.Y. [Xi' an Jiaotong Univ., Xi' an (China). State Key Laboratory of Multiphase Flow, Dept. of Environmental Engineering

    2010-07-01

    In this study, nickel (Ni) and antimony (Sb) doped tin dioxide (SnO{sub 2}) were prepared using a dip-coating pyrolysis method. The sol-gel dip coating method was used to prepare the Ni-Sb-SnO{sub 2} electrode. Scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) analyses were conducted to compare the morphology, crystallinity, composition and oxidation states achieved using the 2 different preparation methods. Results of the evaluation showed that electrodes prepared by the sol-gel method were much different than those prepared using the dip-coating pyrolysis method. Silver (Ag) and cerium (Ce) were doped onto the Ni and Sb doped SnO{sub 2}, and the relations between electrode properties and performance were investigated. Results demonstrated that Ag and Ce doping significantly improved electrode performance. The sol-gel dip coating method also significantly improved electrode performance. 2 refs., 1 fig.

  1. EFFECT OF CERIUM ION IMPLANTATION ON THE AQUEOUS CORROSION BEHAVIOR OF ZIRCONIUM

    Institute of Scientific and Technical Information of China (English)

    D.Q. Peng; X.D. Bai; Q.G. Zhou; X.W. Chen; R.H. Yu; X.Y. Liu

    2004-01-01

    In order to study the influence of cerium ion implantation on the aqueous corrosion behavior of zirconium, specimens were implanted by cerium ions with a dosage range from 1 ×1016 to 1 ×1017 ions/cm2 at about 150℃, using MEWA source at an acceler ative voltage of 40kV. The valence of the surface layer was analyzed by X-ray photoelectron spectroscopy (XPS); Three-sweep potentiodynamic polarization measurement was employed to value the aqueous corrosion resistance of zirconium in a 0.5mol/L H2SO4 solution. It was found that a remarkable decline in the aqueous corrosion behavior of zirconium implanted with cerium ions compared with that of the as-received zirconium. Finally, the mechanism of the corrosion resistance decline of the cerium-implanted zirconium is discussed.

  2. Study on Catalysts with Rhodium Loading on Different Cerium-Zirconium Mixed Oxides

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The catalysts with Rh loading on different cerium-zirconium mixed oxides were characterized by BET, H2-TPR and OSC. The effects of different cerium-zirconium mixed oxides on catalytic performance and thermal stability of Rh loaded catalyst were studied. The results show that: (1) Rh can enhance cerium-zirconium mixed oxides OSC and catalytic reaction rates; (2) cerium-zirconium mixed oxides with high Ce contents and low Zr contents are more favorable to the stability of catalysts. Moreover, the contents of CeO2 have important effect on catalysts characteristics, and the addition of some rare earth components, such as La, Pr and Nd also have some influences.

  3. Synthesis of cerium oxide (CeO{sub 2}) nanoparticles using simple CO-precipitation method

    Energy Technology Data Exchange (ETDEWEB)

    Farahmandjou, M.; Zarinkamar, M.; Firoozabadi, T. P., E-mail: farahamndjou@iauvaramin.ac.ir [Islamis Azad University, Varamin-Phisva Branch, Department of Physics, Varamin (Iran, Islamic Republic of)

    2016-11-01

    Synthesis of cerium oxide (CeO{sub 2}) nanoparticles was studied by new and simple co-precipitation method. The cerium oxide nanoparticles were synthesized using cerium nitrate and potassium carbonate precursors. Their physicochemical properties were characterized by high resolution transmission electron microscopy (HRTEM), scanning electron microscopy (Sem), X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (Ftir) and UV-Vis spectrophotometer. XRD pattern showed the cubic structure of the cerium oxide nanoparticles. The average particle size of CeO{sub 2} was around 20 nm as estimated by XRD technique and direct HRTEM observations. The surface morphological studies from Sem and Tem depicted spherical particles with formation of clusters. The sharp peaks in Ftir spectrum determined the existence of CeO{sub 2} stretching mode and the absorbance peak of UV-Vis spectrum showed the bandgap energy of 3.26 eV. (Author)

  4. Inhaled Diesel Emissions Generated with Cerium Oxide Nanoparticle Fuel Additive Induce Adverse Pulmonary and Systemic Effects

    Science.gov (United States)

    Diesel exhaust (DE) exposure induces adverse cardiopulmonary effects. Cerium oxide nanoparticles added to diesel fuel (DECe) increases fuel burning efficiency but leads to altered emission characteristics and potentially altered health effects. Here, we evaluated whether DECe res...

  5. SELECTION OF OXIDES FOR STABILIZATION OF ZIRCONIUM DIOXIDE WHILE OBTAINING THERMAL BARRIER COATINGS

    Directory of Open Access Journals (Sweden)

    V. V. Okovity

    2015-01-01

    Full Text Available The paper analyzes selection of oxides and describes in details a majority of oxide systems which are applicable for stabilization of zirconium dioxide while obtaining thermal barrier coatings with maximum amount of tetragonal phase. Methodology of investigation is based on a review of analytical information on the current state of thermal barrier coatings on the basis of zirconium dioxide stabilized by oxides of rare-earth metals. The method used for application of  zirconium dioxide thermal barrier coatings is plasma spraying. Positive results have been also obtained while applying e-beam sputtering, ion-plasma deposition and magnetron sputtering. Nevertheless preferred plasma spraying application for thermal barrier coatings still continues due to its high productivity and versatility that permits to deposit metallic and ceramic materials of the ordered chemical and phase composition.Ytterbium and cerium oxides have been selected as oxides for stabilization of zirconium dioxide in order to obtain thermal barrier coatings. The paper also considers аn oxide system of zirconium dioxide: “hafnium oxide – yttrium oxide”, representing in itself the structure which is similar to zirconium dioxide.

  6. Cerium Aryloxides as Precursors for Monopentamethylcyclopentadienyl Organocerium(III) Compounds; X-Ray Crystal Structure of (η5-Pentamethylcyclopentadienyl)bis(2,6-di-t-butylphenoxo)cerium

    NARCIS (Netherlands)

    Heeres, Hero J.; Meetsma, Auke; Teuben, Jan H.

    1988-01-01

    Tris(2,6-di-t-butylphenoxo)cerium reacts with (C5Me5)Li in pentane to form (η5-C5Me5)bis(2,6-di-t-butylphenoxo)cerium, whose structure was established by X-ray crystallography and which, on subsequent reaction with LiCH(SiMe3)2, gives a novel mono(C5Me5)cerium-bisalkyl complex,

  7. Transformation of Cerium Oxide Nanoparticles from a Diesel Fuel Additive during Combustion in a Diesel Engine.

    Science.gov (United States)

    Dale, James G; Cox, Steven S; Vance, Marina E; Marr, Linsey C; Hochella, Michael F

    2017-02-21

    Nanoscale cerium oxide is used as a diesel fuel additive to reduce particulate matter emissions and increase fuel economy, but its fate in the environment has not been established. Cerium oxide released as a result of the combustion of diesel fuel containing the additive Envirox, which utilizes suspended nanoscale cerium oxide to reduce particulate matter emissions and increase fuel economy, was captured from the exhaust stream of a diesel engine and was characterized using a combination of bulk analytical techniques and high resolution transmission electron microscopy. The combustion process induced significant changes in the size and morphology of the particles; ∼15 nm aggregates consisting of 5-7 nm faceted crystals in the fuel additive became 50-300 nm, near-spherical, single crystals in the exhaust. Electron diffraction identified the original cerium oxide particles as cerium(IV) oxide (CeO2, standard FCC structure) with no detectable quantities of Ce(III), whereas in the exhaust the ceria particles had additional electron diffraction reflections indicative of a CeO2 superstructure containing ordered oxygen vacancies. The surfactant coating present on the cerium oxide particles in the additive was lost during combustion, but in roughly 30% of the observed particles in the exhaust, a new surface coating formed, approximately 2-5 nm thick. The results of this study suggest that pristine, laboratory-produced, nanoscale cerium oxide is not a good substitute for the cerium oxide released from fuel-borne catalyst applications and that future toxicity experiments and modeling will require the use/consideration of more realistic materials.

  8. Catalysts with Cerium in a Membrane Reactor for the Removal of Formaldehyde Pollutant from Water Effluents

    OpenAIRE

    2016-01-01

    We report the synthesis of cerium oxide, cobalt oxide, mixed cerium, and cobalt oxides and a Ce–Co/Al2O3 membrane, which are employed as catalysts for the catalytic wet oxidation (CWO) reaction process and the removal of formaldehyde from industrial effluents. Formaldehyde is present in numerous waste streams from the chemical industry in a concentration low enough to make its recovery not economically justified but high enough to create an environmental hazard. Common biological degradation ...

  9. An investigation of the use of cerium and polyhedral oligomeric silsesquioxanes for the protection of polymeric epoxy compounds in the low Earth orbit environment

    Science.gov (United States)

    Piness, Jessica Miriam

    Low Earth orbit presents many hazards for composites including atomic oxygen, UV radiation, thermal cycling, micrometeoroids, and high energy protons. Atomic oxygen and vacuum ultraviolet radiation are of concern for space-bound polymeric materials as they degrade the polymers used as matrices for carbon fiber composites, which are used in satellites and space vehicles due to their high strength to weight ratios. Epoxy-amine thermosets comprise a common class of matrix due to processability and good thermal attributes. Polyhedral oligomeric silsesquioxanes (POSS) have shown the ability to reduce erosion in polyimides, polyurethanes, and other polymers when exposed to atomic oxygen. The POSS particle is composed of a SiO1.5 cage from which up to eight organic pendant groups are attached at the silicon corners of the cage. POSS reduced atomic oxygen impact on polymers by a process known as glassification wherein the organic pendants are removed from the cage upon atomic oxygen exposure and then the cage rearranges to a passive silica network. In addition, POSS shows good UV absorbance in the UVb and UVc ranges and POSS can aid dispersion of titanium dioxide in a nanocomposite. In this work, Chapter I focuses on hazards in low Earth orbit, strategies for protecting organic material in orbit, and the capabilities of POSS. Chapter II details the experimental practices used in this work. Chapter III focuses on work to induce POSS phase separation and layering at the surface of an epoxy-amine thermoset. Generally, POSS is dispersed throughout a nanocomposite, and in the process of erosion by atomic oxygen, some polymer mass loss is lost before enough POSS is exposed to begin glassification. Locating POSS at a surface of composite could possibly reduce this mass loss and the objective of this research was to investigate the formation of POSS-rich surfaces. Three POSS derivatives with different pendant groups were chosen. The POSS derivatives had a range of miscibilities

  10. Thermal Treatment of Cerium Oxide and Its Properties: Adsorption Ability versus Degradation Efficiency

    Directory of Open Access Journals (Sweden)

    Pavel Janoš

    2014-01-01

    Full Text Available Cerium oxide belongs to the most important heterogeneous catalysts, but its applicability as so-called reactive sorbent for the degradation of toxic chemicals was only recently discovered. For these purposes, cerium oxide is prepared by precipitation of insoluble cerium salts (carbonates with a subsequent thermal decomposition. Properties of cerium oxide prepared from the carbonate precursor are strongly affected by the temperature during the calcination. Main physicochemical properties of cerium oxide (specific surface area, crystallinity, and surface chemistry were examined in dependence on the calcination temperature. As the adsorptive properties of CeO2 are undoubtedly of great importance in the abovementioned applications, the adsorption ability was studied using an azo dye Acid Orange 7 (AO7 as a model compound. The highest sorption efficiency towards AO7 exhibited sorbents prepared at temperatures below 700°C, which was attributed mainly to the presence of hydroxyl groups on the oxide surface. A strong correlation was found between an adsorption efficiency of cerium oxides and their degradation efficiency for organophosphate pesticide parathion methyl. The >Ce–OH groups on the sorbent surface are responsible for the dye binding by the surface-complexation mechanism, and probably also for the nucleophilic cleavage of the P–O–aryl bond in the pesticide molecule.

  11. Characterization of a zinc-cerium flow battery

    Science.gov (United States)

    Leung, P. K.; Ponce-de-León, C.; Low, C. T. J.; Shah, A. A.; Walsh, F. C.

    The performance of a divided, parallel-plate zinc-cerium redox flow battery using methanesulfonic acid electrolytes was studied. Eight two and three-dimensional electrodes were tested under both constant current density and constant cell voltage discharge. Carbon felt and the three-dimensional platinised titanium mesh electrodes exhibited superior performance over the 2-dimensional electrodes. The charge and discharge characteristics of the redox flow battery were studied under different operating conditions and Zn/Ce reactant, as well as methansulfonic acid concentration. The cell performance improved at higher operating temperatures and faster electrolyte flow velocities. The number of possible cycles increased at reduced states of charge. During 15 min charge/discharge per cycle experiment, 57 cycles were obtained and the zinc reaction was found to be the limiting process during long term operation.

  12. Geometry of electromechanically active structures in Gadolinium - doped Cerium oxides

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yuanyuan; Zacharowicz, Renee; Frenkel, Anatoly I., E-mail: igor.lubomirsky@weizmann.ac.il, E-mail: anatoly.frenkel@yu.edu [Physics Department, Yeshiva University, 245 Lexington Avenue, New York, New York 10016 (United States); Kraynis, Olga; Lubomirsky, Igor, E-mail: igor.lubomirsky@weizmann.ac.il, E-mail: anatoly.frenkel@yu.edu [Department of Materials and Interfaces, Weizmann Institute of Science, Rehovot 76100 (Israel); Kas, Joshua [Department of Physics, University of Washington, Seattle, Washington 98195 (United States); Weng, Tsu-Chien; Sokaras, Dimosthenis [Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States)

    2016-05-15

    Local distortions from average structure are important in many functional materials, such as electrostrictors or piezoelectrics, and contain clues about their mechanism of work. However, the geometric attributes of these distortions are exceedingly difficult to measure, leading to a gap in knowledge regarding their roles in electromechanical response. This task is particularly challenging in the case of recently reported non-classical electrostriction in Cerium-Gadolinium oxides (CGO), where only a small population of Ce-O bonds that are located near oxygen ion vacancies responds to external electric field. We used high-energy resolution fluorescence detection (HERFD) technique to collect X-ray absorption spectra in CGO in situ, with and without an external electric field, coupled with theoretical modeling to characterize three-dimensional geometry of electromechanically active units.

  13. Growth of transition metals on cerium tungstate model catalyst layers

    Science.gov (United States)

    Skála, T.; Tsud, N.; Stetsovych, V.; Mysliveček, J.; Matolín, V.

    2016-10-01

    Two model catalytic metal/oxide systems were investigated by photoelectron spectroscopy and scanning tunneling microscopy. The mixed-oxide support was a cerium tungstate epitaxial thin layer grown in situ on the W(1 1 0) single crystal. Active particles consisted of palladium and platinum 3D islands deposited on the tungstate surface at 300 K. Both metals were found to interact weakly with the oxide support and the original chemical state of both support and metals was mostly preserved. Electronic and morphological changes are discussed during the metal growth and after post-annealing at temperatures up to 700 K. Partial transition-metal coalescence and self-cleaning from the CO and carbon impurities were observed.

  14. Cerium intermetallics with TiNiSi-type structure

    Energy Technology Data Exchange (ETDEWEB)

    Janka, Oliver; Niehaus, Oliver; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Chevalier, Bernard [Bordeaux Univ. CNRS (UPR 9048), Pessac (France). Inst. de Chimie de la Matiere Condensee de Bordeaux (ICMCB)

    2016-08-01

    Intermetallic compounds with the equiatomic composition CeTX that crystallize with the orthorhombic TiNiSi-type structure can be synthesized with electron-rich transition metals (T) and X = Zn, Al, Ga, Si, Ge, Sn, As, Sb, and Bi. The present review focusses on the crystal chemistry and chemical bonding of these CeTX phases and on their physical properties, {sup 119}Sn and {sup 121}Sb Moessbauer spectra, high-pressure effects, hydrogenation reactions and the formation of solid solutions in order to elucidate structure-property relationships. This paper is the final one of a series of four reviews on equiatomic intermetallic cerium compounds [Part I: Z. Naturforsch. 2015, 70b, 289; Part II: Z. Naturforsch. 2015, 70b, 695; Part III: Z. Naturforsch. 2016, 71b, 165].

  15. On the mixed nature of cerium conversion coatings

    Energy Technology Data Exchange (ETDEWEB)

    Botana, F.J.; Aballe, A.; Bethencourt, M.; Cano, M.J. [Cadiz Univ. (Spain). Dept. de Ciencia de los Materiales e Ingenieria Metalurgica y Quimica Inorganica; Marcos, M. [Cadiz Univ. (Spain). Dept. de Ingenieria Mecanica y Diseno Industrial

    2002-03-01

    Alternative pretreatments are currently under development in order to avoid the environmental impact produced by using surface finishing processes based on chromates. Some of the environmentally friendly alternatives proposed involve the use of lanthanide based compounds. In this study, conversion coatings on AA5083 (Al-Mg) samples developed using full immersion pretreatments in 500 ppm CeCl{sub 3} aqueous solutions have been investigated. Their microscopic and compositional features have been analyzed using SEM images and EDS spectra. From this analysis it has been determined that this layer over the surface of the samples is of a heterogeneous composition. This coating is formed by an alumina coating covering the aluminum matrix and dispersed cerium-rich islands deposited over the cathodic sites of the alloy. A characterization methodology is proposed based on the utilization of different electrochemical techniques, such as open circuit potential monitoring (OCP), linear polarization (LP) and electrochemical impedance spectroscopy (EIS). (orig.)

  16. Interplay of spin-orbit and entropic effects in cerium

    Energy Technology Data Exchange (ETDEWEB)

    Lanata, Nicola [Rutgers University; Yao, Yong-Xin [Ames Laboratory; Wang, Cai-Zhuang [Ames Laboratory; Ho, Kai-Ming [Ames Laboratory; Kotliar, Gabriel [Rutgers University

    2014-10-01

    We perform first-principles calculations of elemental cerium and compute its pressure-temperature phase diagram, finding good quantitative agreement with the experiments. Our calculations indicate that, while a signature of the volume-collapse transition appears in the free energy already at low temperatures, at higher temperatures this signature is enhanced because of the entropic effects, and originates an actual thermodynamical instability. Furthermore, we find that the catalyst determining this feature is—in all temperature regimes—a pressure-induced effective reduction of the f-level degeneracy due to the spin-orbit coupling. Our analysis suggests also that the lattice vibrations might be crucial in order to capture the behavior of the pressure-temperature transition line at large temperatures.

  17. EPDM composite membranes modified with cerium doped lead zirconate titanate

    Science.gov (United States)

    Zaharescu, T.; Dumitru, A.; Lungulescu, M. E.; Velciu, G.

    2016-01-01

    This study was performed on γ-irradiated ethylene-propylene diene terpolymer (EPDM) loaded with lead zirconate titanate. The inorganic phase has a perovskite structure with general formula Pb(Zr0.65-xCexTi0.35)O3. The three composites with different Ce dopant concentrations revealed the stabilization activity of filler against oxidation proved by chemiluminescence investigation in respect to pristine polymer. The presence of cerium low concentrations in the solid lead zirconate titanate nanoparticles causes significant slowing of oxidation rate during radiation exposure. The improvement in the stabilization feature of filler is correlated with the existence of traps, whose interaction with free radicals assumes medium energy due to their convenient depth.

  18. Effect of Surface Modification on Behaviors of Cerium Oxide Nanopowders

    Institute of Scientific and Technical Information of China (English)

    Li Mei; Shi Zhenxue; Liu Zhaogang; Hu Yanhong; Wang Mitang; Li Hangquan

    2007-01-01

    Study was made on the effect of surface modification on the behaviors of cerium oxide nanopowders. A surfactant-sodium dodecyl sulfate(C12H25SO4Na) was used to modify the surface of CeO2 powder particles. The unmodified and modified CeO2 powders were characterized by using a powder comprehensive characteristic tester, laser particle size analyzer, specific surface area tester, X-ray diffraction tester, and a scanning electron microscope. The testing and analysis results showed that C12H25SO4Na surface modification might increase the flowability and dispersity, and decrease the specific surface area and agglomeration of CeO2 powders. The mechanism of the surface modification of CeO2 powder particles was also discussed.

  19. Thermopower enhancement by encapsulating cerium in clathrate cages.

    Science.gov (United States)

    Prokofiev, A; Sidorenko, A; Hradil, K; Ikeda, M; Svagera, R; Waas, M; Winkler, H; Neumaier, K; Paschen, S

    2013-12-01

    The increasing worldwide energy consumption calls for the design of more efficient energy systems. Thermoelectrics could be used to convert waste heat back to useful electric energy if only more efficient materials were available. The ideal thermoelectric material combines high electrical conductivity and thermopower with low thermal conductivity. In this regard, the intermetallic type-I clathrates show promise with their exceedingly low lattice thermal conductivities. Here we report the successful incorporation of cerium as a guest atom into the clathrate crystal structure. In many simpler intermetallic compounds, this rare earth element is known to lead, through the Kondo interaction, to strong correlation phenomena including the occurrence of giant thermopowers at low temperatures. Indeed, we observe a 50% enhancement of the thermopower compared with a rare-earth-free reference material. Importantly, this enhancement occurs at high temperatures and we suggest that a rattling-enhanced Kondo interaction underlies this effect.

  20. Structure and Electronic Properties of Cerium Orthophosphate: Theory and Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Adelstein, Nicole; Mun, B. Simon; Ray, Hannah; Ross Jr, Phillip; Neaton, Jeffrey; De Jonghe, Lutgard

    2010-07-27

    Structural and electronic properties of cerium orthophosphate (CePO{sub 4}) are calculated using density functional theory (DFT) with the local spin-density approximation (LSDA+U), with and without gradient corrections (GGA-(PBE)+U), and compared to X-ray diffraction and photoemission spectroscopy measurements. The density of states is found to change significantly as the Hubbard parameter U, which is applied to the Ce 4f states, is varied from 0 to 5 eV. The calculated structural properties are in good agreement with experiment and do not change significantly with U. Choosing U = 3 eV for LDSA provides the best agreement between the calculated density of states and the experimental photoemission spectra.

  1. The Spin Glass-Kondo Competition in Disordered Cerium Systems

    Science.gov (United States)

    Magalhaes, S. G.; Zimmer, F.; Coqblin, B.

    2013-10-01

    We discuss the competition between the Kondo effect, the spin glass state and a magnetic order observed in disordered Cerium systems. We present firstly the experimental situation of disordered alloys such as CeNi1 - xCux and then the different theoretical approaches based on the Kondo lattice model, with different descriptions of the intersite exchange interaction for the spin glass. After the gaussian approach of the Sherrington-Kirkpatrick model, we discuss the Mattis and the van Hemmen models. Then, we present simple cluster calculations in order to describe the percolative evolution of the clusters from the cluster spin glass to the inhomogeneous ferromagnetic order recently observed in CeNi1 - xCux disordered alloys and finally we discuss the effect of random and transverse magnetic field.

  2. Mechanochemical synthesis and spark plasma sintering of the cerium silicides

    Energy Technology Data Exchange (ETDEWEB)

    Alanko, Gordon A.; Jaques, Brian; Bateman, Allyssa [Department of Materials Science and Engineering, College of Engineering, Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Butt, Darryl P., E-mail: darrylbutt@boisestate.edu [Department of Materials Science and Engineering, College of Engineering, Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Center for Advanced Energy Studies, 995 University Boulevard, Idaho Falls, ID 83401 (United States)

    2014-12-15

    Highlights: • Ce{sub 5}Si{sub 3}, Ce{sub 3}Si{sub 2}, CeSi, CeSi{sub 2−x} and CeSi{sub 2} were mechanochemically synthesized. • Temperature and pressure were monitored to investigate reaction progress. • All syntheses proceeded through a MSR event followed by rapid solid-state diffusion. • Milling time before MSR correlates well with effective heat of formation. • Some synthesized material was densified by spark plasma sintering. - Abstract: The cerium silicides, Ce{sub 5}Si{sub 3}, Ce{sub 3}Si{sub 2}, CeSi, CeSi{sub 2−y}, and CeSi{sub 2−x}, have been prepared from the elements by mechanochemical processing in a planetary ball mill. Preparation of the cerium silicide Ce{sub 5}Si{sub 4} was unsuccessfully attempted and potential reasons for this are discussed. Temperature and pressure of the milling vial were monitored in situ to gain insight into the mechanochemical reaction kinetics, which include a mechanically-induced self-propagating reaction (MSR). Some prepared powders were consolidated by spark plasma sintering to high density. Starting materials, as-milled powders, and consolidated samples were characterized by X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy. The results obtained help elucidate key questions in mechanochemical processing of intermetallics, showing first phase formation similar to thin films, MSR ignition times that are composition- and milling speed-dependent, and sensitivity of stable compound formation on the impact pressure. The results demonstrate mechanochemical synthesis as a viable technique for rare earth silicides.

  3. The carbon dioxide cycle

    Science.gov (United States)

    James, P.B.; Hansen, G.B.; Titus, T.N.

    2005-01-01

    The seasonal CO2 cycle on Mars refers to the exchange of carbon dioxide between dry ice in the seasonal polar caps and gaseous carbon dioxide in the atmosphere. This review focuses on breakthroughs in understanding the process involving seasonal carbon dioxide phase changes that have occurred as a result of observations by Mars Global Surveyor. ?? 2004 COSPAR. Published by Elsevier Ltd. All rights reserved.

  4. Carbon Dioxide Absorbents

    Science.gov (United States)

    1950-05-17

    carbondioxide content of the solution was then determined. A gas mixture containing 2.6% carbon dioxide and 97.4% nitrogen was prepared in the...which carbon dioxide is removed by heat0 Since this step is usually carried out by "steam stripping ", that is, contacting the solution at its boiling...required to produce the steam required for stripping the carbon dioxide from the s olution. The method ueed in this investigation for determining the

  5. CARBON DIOXIDE REDUCTION SYSTEM.

    Science.gov (United States)

    CARBON DIOXIDE , *SPACE FLIGHT, RESPIRATION, REDUCTION(CHEMISTRY), RESPIRATION, AEROSPACE MEDICINE, ELECTROLYSIS, INSTRUMENTATION, ELECTROLYTES, VOLTAGE, MANNED, YTTRIUM COMPOUNDS, ZIRCONIUM COMPOUNDS, NICKEL.

  6. Inactivation of Escherichia coli by titanium dioxide photocatalytic oxidation.

    Science.gov (United States)

    Titanium dioxide in the anatase crystalline form was used as a photocatalyst to generate hydroxyl radicals in a flowthrough water reactor. Experiments were performed on pure cultures of Escherichia coli in dechlorinated tap water and a surface water sample to evaluate the disinfe...

  7. Relativity of pure states entanglement

    CERN Document Server

    Zyczkowski, K; Zyczkowski, Karol; Bengtsson, Ingemar

    2002-01-01

    Entanglement of any pure state of an N times N bi-partite quantum system may be characterized by the vector of coefficients arising by its Schmidt decomposition. We analyze various measures of entanglement derived from the generalized entropies of the vector of Schmidt coefficients. For N >= 3 they generate different ordering in the set of pure states and for some states their ordering depends on the measure of entanglement used. This odd-looking property is acceptable, since these incomparable states cannot be transformed to each other with unit efficiency by any local operation. In analogy to special relativity the set of pure states equivalent under local unitaries has a causal structure so that at each point the set splits into three parts: the 'Future', the 'Past' and the set of noncomparable states.

  8. "Pure" cutaneous histiocytosis-X.

    Science.gov (United States)

    Wolfson, S L; Botero, F; Hurwitz, S; Pearson, H A

    1981-11-15

    The case histories of two young children who experienced skin rashes involving various areas of the body are reported. The diagnosis of pure cutaneous histiocytosis-X was established after extensive studies revealed no other organ involvement. The patients were treated with oral corticosteroids. Currently, both children are in good health, show no evidence of disease, and have been followed over a four-to-five-year period. Therapy with corticosteroids may not be indicated with pure cutaneous histiocytosis-X unless there is evidence of extracutaneous dissemination or rapid progression of the disease.

  9. Pure Spinors for General Backgrounds

    CERN Document Server

    Fre', Pietro

    2008-01-01

    We show the equivalence of the different types of pure spinor constraints geometrically derived from the Free Differential Algebras of N=2 d=10 supergravities. Firstly, we compute the general solutions of these constraints, using both a G_2 and an SO(8) covariant decomposition of the 10d chiral spinors. Secondly, we verify that the number of independent degrees of freedom is equal to that implied by the Poincare' pure spinor constraints so-far used for superstrings, namely twenty two. Thirdly, we show the equivalence between the FDA type IIA/B constraints among each other and with the Poincare' ones.

  10. Effects of cerium nitrate on the growth and physiological characteristics in Cyclocarya paliurusseedlings

    Institute of Scientific and Technical Information of China (English)

    谢寅峰; 李颖; 刘娜娜; 张颖颖; 郭楠; 王涛; 尚绪岚

    2015-01-01

    Field studies were conducted to examine the effects of cerium on the growth and physiological characteristics ofCyclo-carya paliurusseedlings by spraying the foliage with different concentrations of cerium nitrate. Optimal concentrations of cerium ni-trate improved the relative growth yield of seedling height and stems and the soluble protein and sugar content of the leaves. Cerium nitrate also increased the concentration of secondary metabolites including triterpenoids, quercetin and kaempferol, mineral elements K, P, Mg, Mn, Fe and Cu, and the activities of superoxide dismutase (SOD), peroxidase (POX), and phenylalanine ammonia-lyase (PAL) in the leaves. The effects of cerium nitrate on these indices were dose dependent. A concentration of 0.20 mmol/L was optimal to promote the relative growth yield of seedling height, contents of soluble sugar, kaempferol, K, P, Cu, and activities of PAL, SOD, and POX, significantlyincreased by 54.61%, 14.71%, 55.19%, 105.2%, 74.5%, 133.3%, 80.48%, 25.35% and 22.54%, respectively, as compared with the control. However, the maximal increase in relative growth yield of stems, contents of triterpenoid, quercetin, Mg, Mn, and Fe was attained at 1.00 mmol/L treatment, which significantlyincreased by 87.00%, 80.56%, 452.44%, 93.2%, 29.4%, and 133.9%, respectively, compared with control check (CK). Correlation analysis revealed positive relationships between activities of PAL, SOD and contents of triterpenoid, quercetin and kaempferol within a certain concentration range of cerium nitrate. These re-sults suggested that an appropriate concentration of cerium not only was effective in the improvement of physiological function ofC. paliurus, but alsoincreased seedling resistance. Moreover, it stimulated the synthesis of medicinal components in leaves.

  11. Gadolinium doped tin dioxide nanoparticles:an efficient visible light active photocatalyst

    Institute of Scientific and Technical Information of China (English)

    Abdullah M Al-Hamdi; Mika Sillanp; Joydeep Dutta

    2015-01-01

    Photocatalytic degradation of phenol with sol-gel prepared rare earth doped tin dioxide (SnO2) nanoparticles was reported. Gadolinium doped tin dioxide (SnO2:Gd) nanoparticles were found to absorb higher visible light compared to lanthanum, neodymium and cerium doped materials that were studied in detail. Photocatalytic degradation of phenol under artificial white light and sunlight in the presence of SnO2:Gd nanoparticles was studied with high performance liquid chromatography (HPLC), capillary electrophoresis (CE), total organic carbon (TOC) measurements and the determination of chemical oxygen demand (COD). Clear correlations be-tween the results obtained from these multiple measurements were found, and a kinetic pathway for the degradation process was pro-posed. Within 150 min of solar irradiation, the TOC of a 10 ppm phenol solution in water was reduced by 95%–99%, thus demon-strating that SnO2:Gd nanoparticles are efficient visible light photocatalysts.

  12. Carbon Dioxide and Climate.

    Science.gov (United States)

    Brewer, Peter G.

    1978-01-01

    The amount of carbon dioxide in the atmosphere is increasing at a rate that could cause significant warming of the Earth's climate in the not too distant future. Oceanographers are studying the role of the ocean as a source of carbon dioxide and as a sink for the gas. (Author/BB)

  13. Carbon Dioxide Fountain

    Science.gov (United States)

    Kang, Seong-Joo; Ryu, Eun-Hee

    2007-01-01

    This article presents the development of a carbon dioxide fountain. The advantages of the carbon dioxide fountain are that it is odorless and uses consumer chemicals. This experiment also is a nice visual experiment that allows students to see evidence of a gaseous reagent being consumed when a pressure sensor is available. (Contains 3 figures.)…

  14. Exposure, Health and Ecological Effects Review of Engineered Nanoscale Cerium and Cerium Oxide Associated with its Use as a Fuel Additive

    Science.gov (United States)

    Advances of nanoscale science have produced nanomaterials with unique physical and chemical properties at commercial levels which are now incorporated into over 1000 products. Nanoscale cerium (di) oxide (CeO(2)) has recently gained a wide range of applications which includes coa...

  15. Pure robotic retrocaval ureter repair

    Directory of Open Access Journals (Sweden)

    Ashok k. Hemal

    2008-12-01

    Full Text Available PURPOSE: To demonstrate the feasibility of pure robotic retrocaval ureter repair. MATERIALS AND METHODS: A 33 year old female presented with right loin pain and obstruction on intravenous urography with the classical "fish-hook" appearance. She was counseled on the various methods of repair and elected to have a robot assisted repair. The following steps are performed during a pure robotic retrocaval ureter repair. The patient is placed in a modified flank position, pneumoperitoneum created and ports inserted. The colon is mobilized to expose the retroperitoneal structures: inferior vena cava, right gonadal vein, right ureter, and duodenum. The renal pelvis and ureter are mobilized and the renal pelvis transected. The ureter is transposed anterior to the inferior vena cava and a pyelopyelostomy is performed over a JJ stent. RESULTS: This patient was discharged on postoperative day 3. The catheter and drain tube were removed on day 1. Her JJ stent was removed at 6 weeks postoperatively. The postoperative intravenous urography at 3 months confirmed normal drainage of contrast medium. CONCLUSION: Pure robotic retrocaval ureter is a feasible procedure; however, there does not appear to be any great advantage over pure laparoscopy, apart from the ergonomic ease for the surgeon as well the simpler intracorporeal suturing.

  16. Thermochemical Modeling of the Uranium-Cerium-Oxygen System

    Energy Technology Data Exchange (ETDEWEB)

    Voit, Stewart L [ORNL; Besmann, Theodore M [ORNL

    2010-10-01

    with actinide materials, fundamental studies with uranium are performed using surrogate materials as stand-ins for transuranic elements. In most cases, cerium can be used as a suitable substitute for plutonium when performing O:M and sintering kinetics studies because of identical valence states. Differences exist between the magnitude of reported thermodynamic data of (U,Pu)O{sub x} and (U,Ce)O{sub x}, however the change in oxygen potential versus O:M follows the same trend for both systems. Cerium is also a major fission product element, and thus understanding its behavior in fuel is an important issue as well.

  17. Low temperature hydrogen production from ethanol over cerium and nickel based oxyhydrides

    Energy Technology Data Exchange (ETDEWEB)

    Pirez, Cyril; Jalowiecki-Duhamel, L.; Capron, M.; Dumeignil, F. [Univ. des Sciences et Technologies de Lille (France). UCCS Unite de Catalyse et de Chimie du Solide

    2010-07-01

    In theory, hydrogen production from biomass or biomass derived liquids can be a carbon emission free process since all carbon dioxide produced can be recycled back to plants using solar energy. Besides, ethanol is also safe, simple to handle, transport and store, so ethanol lends itself very well to a distributed-production strategy. A very interesting use of hydrogen is based on its conversion into power in fuel cell systems. The wide-spread application of fuel cells becomes closer to reality, so increased attention is focused on hydrogen production technology. Solid oxide fuel cells (SOFCs) are under development as energy production devices, they allow the use of carbon-monoxide resistant nickel anodes and the use of fuels different from hydrogen at the anode, in the so-called direct internal reforming SOFC. However the high operating temperatures undergo catalytic deactivation due to sintering of nickel crystallites and carbon deposition. Hence, worldwide efforts are in progress to discover novel, more active and more stable catalysts. Performing the reaction at lower temperature than 600 C is a challenging goal. C{sub 2}H{sub 5}OH + 3 H{sub 2}O {yields} 2 CO{sub 2} + 6 H{sub 2} (1). Hydrogen production from ethanol steam reforming (H{sub 2}O/C{sub 2}H{sub 5}OH = 3) was investigated over cerium nickel CeNi{sub X}O{sub Y} and (0 < x {<=} 5) mixed oxide catalysts. The influence of different parameters was analysed, such as reaction temperature, Ni content and in-situ pre-treatment in H{sub 2}. While an ethanol conversion of 100 % is reached at 400 C, a stable activity i.e. ethanol conversion, and H{sub 2} selectivity can be obtained at very low temperature (200 C) when the solid is previously in-situ treated in H{sub 2} in a temperature range between 200 C and 300 C. In the present study, we report on H{sub 2} formation activity over CeNi{sub X}O{sub Y} catalysts for reforming of ethanol. The aim of this work was to develop a highly active, selective, stable and

  18. Carbon ion pump for removal of carbon dioxide from combustion gas and other gas mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Aines, Roger D.; Bourcier, William L.

    2014-08-19

    A novel method and system of separating carbon dioxide from flue gas is introduced. Instead of relying on large temperature or pressure changes to remove carbon dioxide from a solvent used to absorb it from flue gas, the ion pump method, as disclosed herein, dramatically increases the concentration of dissolved carbonate ion in solution. This increases the overlying vapor pressure of carbon dioxide gas, permitting carbon dioxide to be removed from the downstream side of the ion pump as a pure gas. The ion pumping may be obtained from reverse osmosis, electrodialysis, thermal desalination methods, or an ion pump system having an oscillating flow in synchronization with an induced electric field.

  19. Carbon ion pump for removal of carbon dioxide from combustion gas and other gas mixtures

    Science.gov (United States)

    Aines, Roger D.; Bourcier, William L.

    2010-11-09

    A novel method and system of separating carbon dioxide from flue gas is introduced. Instead of relying on large temperature or pressure changes to remove carbon dioxide from a solvent used to absorb it from flue gas, the ion pump method, as disclosed herein, dramatically increases the concentration of dissolved carbonate ion in solution. This increases the overlying vapor pressure of carbon dioxide gas, permitting carbon dioxide to be removed from the downstream side of the ion pump as a pure gas. The ion pumping may be obtained from reverse osmosis, electrodialysis, thermal desalination methods, or an ion pump system having an oscillating flow in synchronization with an induced electric field.

  20. Effects of precipitate aging time on the cerium-zirconium composite oxides

    Institute of Scientific and Technical Information of China (English)

    钟强; 崔梅生; 岳梅; 王琦; 王磊; 郭荣贵; 龙志奇; 黄小卫

    2014-01-01

    Cerium-zirconium composite oxides with high performance were synthesized by a co-precipitation method, using zirco-nium oxychloride and rare earth chloride as raw materials. The effects of precipitate aging time on the properties of cerium-zirconium composite oxides were investigated. The prepared cerium-zirconium composite oxides were characterized by X-ray diffraction (XRD), BET specific surface area, pulsed oxygen chemical adsorption, H2 temperature-programmed-reduction (H2-TPR), scanning electron microscopy (SEM), etc. The results showed that the precipitate aging time caused great effects on the properties of cerium zirconium composite oxides. With the increase of aging time, the cerium zirconium composite oxides showed enhanced specific sur-face area, good thermal stability, and high oxygen storage capacity (OSC). The best performance sample was obtained while the pre-cipitate aging time up to 48 h, with the specific surface area of 140.7 m2/g, and OSC of 657.24μmolO2/g for the fresh sample. Even after thermal aged under 1000 ºC for 4 h, the aged specific surface area was 41.6 m2/g, moreover with a good OSC of 569.9μmolO2/g.

  1. Structural and luminescent studies on nanosized cerium doped strontium barium niobate

    Science.gov (United States)

    John, Nuja; Nandakumar, K.

    2017-06-01

    The nanosized cerium doped Strontium Barium Niobate ceramic powder system have been synthesized by sol-gel technique. The X-ray diffraction measurement confirmed the structure of cerium doped Strontium Barium Niobate ceramic powder system. The absorption peaks were analysed by FTIR spectroscopy. Particle morphology and size of the powder were examined using SEM and TEM. Crystal quality and structure were also examined by micro raman spectra. The transmission electron microscopy image of cerium doped Strontium Barium Niobate nano powder system consist of particles with average size of 20 nm. A band gap of the system was measured by optical absorption spectra. Photoluminescence data were recorded at room temperature. The emission peaks were detected under excitation at 305 nm wavelength. The peaks are assigned to the cerium electron transition from lowest 5d level to 2F5/2 and 2F7/2 of 4f, respectively. The decay time were also measured for cerium doped Strontium Barium Niobate powder system.

  2. Catalysts with Cerium in a Membrane Reactor for the Removal of Formaldehyde Pollutant from Water Effluents.

    Science.gov (United States)

    Gutiérrez-Arzaluz, Mirella; Noreña-Franco, Luis; Ángel-Cuevas, Saúl; Mugica-Álvarez, Violeta; Torres-Rodríguez, Miguel

    2016-05-24

    We report the synthesis of cerium oxide, cobalt oxide, mixed cerium, and cobalt oxides and a Ce-Co/Al₂O₃ membrane, which are employed as catalysts for the catalytic wet oxidation (CWO) reaction process and the removal of formaldehyde from industrial effluents. Formaldehyde is present in numerous waste streams from the chemical industry in a concentration low enough to make its recovery not economically justified but high enough to create an environmental hazard. Common biological degradation methods do not work for formaldehyde, a highly toxic but refractory, low biodegradability substance. The CWO reaction is a recent, promising alternative that also permits much lower temperature and pressure conditions than other oxidation processes, resulting in economic benefits. The CWO reaction employing Ce- and Co-containing catalysts was carried out inside a slurry batch reactor and a membrane reactor. Experimental results are reported. Next, a mixed Ce-Co oxide film was supported on an γ-alumina membrane used in a catalytic membrane reactor to compare formaldehyde removal between both types of systems. Catalytic materials with cerium and with a relatively large amount of cerium favored the transformation of formaldehyde. Cerium was present as cerianite in the catalytic materials, as indicated by X-ray diffraction patterns.

  3. Production of cerium zinc molybdate nano pigment by innovative ultrasound assisted approach.

    Science.gov (United States)

    Patel, M A; Bhanvase, B A; Sonawane, S H

    2013-05-01

    Ultrasound assisted synthesis of yellow rare earth cerium zinc molybdate anticorrosion nanopigment is presented. This new class of pigment is eco-friendly alternatives to lead, cadmium and chromium pigment as these pigments contains carcinogenic species like Cr(6+) which is responsible for human disease. The synthesis of nanosized cerium zinc molybdate was carried out using cerium nitrate, sodium zinc molybdate as a precursor materials by conventional and ultrasound assisted chemical precipitation method without addition of emulsification agent. XRD, FTIR and elemental analysis confirm the formation of cerium zinc molybdate nanoparticles. The conductivity results indicate that conventional synthesis takes longer time, while in sonochemical technique (US), reaction completes within short period of time. Improved solute transfer rate, rapid nucleation, and formation of large number of nuclei are attributed to presence of cavitation. Saturation of the Ce(3+) ions reaches earlier in case of sonochemical technique which restricts the growth of particles hence smaller size is obtained. The crystallite size of cerium zinc molybdate was found to be 27nm from XRD analysis.

  4. Catalysts with Cerium in a Membrane Reactor for the Removal of Formaldehyde Pollutant from Water Effluents

    Directory of Open Access Journals (Sweden)

    Mirella Gutiérrez-Arzaluz

    2016-05-01

    Full Text Available We report the synthesis of cerium oxide, cobalt oxide, mixed cerium, and cobalt oxides and a Ce–Co/Al2O3 membrane, which are employed as catalysts for the catalytic wet oxidation (CWO reaction process and the removal of formaldehyde from industrial effluents. Formaldehyde is present in numerous waste streams from the chemical industry in a concentration low enough to make its recovery not economically justified but high enough to create an environmental hazard. Common biological degradation methods do not work for formaldehyde, a highly toxic but refractory, low biodegradability substance. The CWO reaction is a recent, promising alternative that also permits much lower temperature and pressure conditions than other oxidation processes, resulting in economic benefits. The CWO reaction employing Ce- and Co-containing catalysts was carried out inside a slurry batch reactor and a membrane reactor. Experimental results are reported. Next, a mixed Ce–Co oxide film was supported on an γ-alumina membrane used in a catalytic membrane reactor to compare formaldehyde removal between both types of systems. Catalytic materials with cerium and with a relatively large amount of cerium favored the transformation of formaldehyde. Cerium was present as cerianite in the catalytic materials, as indicated by X-ray diffraction patterns.

  5. Mechanism of chlorinating lanthanum oxide and cerium oxide with ammonium chloride

    Institute of Scientific and Technical Information of China (English)

    朱国才; 李赋屏; 肖明贵

    2003-01-01

    Using ammonium chloride(NH4Cl)as a chlorinating agent,the effects of chlorinating temperature,at 300℃ for 90 min,and have no advantage to chlorination of lanthanum and cerium oxides at higher temperature.The thermal decomposition of LaCl3 and CeCl3 is carried out to explore the mechanism of chlorinating lanthanum and cerium oxides.At the same time,the chlorination of lanthanum and cerium oxides is not devoted to the HCl decomposed from NH4Cl,but to NH4Cl directly taking part in the chlorination of La2O3 and CeO2.The lanthanum and cerium oxides in chlorination firstly form intermediate LaOCl and CeOCl,and then transfer to LaCl3 and CeCl3,fither prove the existence of the intermediates LaOCl and CeOCl.Therefore the chlorinating temperature and time should strictly be controlled when the lanthanum oxide and cerium oxide are chlorinated with NH4 Cl.And over-dosage of NH4 Cl should be also applied in the process of chlorination.

  6. Application of cerium chloride to improve the acid resistance of dentine.

    Science.gov (United States)

    Wegehaupt, Florian J; Sener, Beatrice; Attin, Thomas; Schmidlin, Patrick R

    2010-06-01

    To investigate the effect of cerium chloride, cerium chloride/fluoride and fluoride application on calcium release during erosion of treated dentine. Forty dentine samples were prepared from human premolars and randomly assigned to four groups (1-4). Samples were treated twice a day for 5 days, 30s each, with the following solutions: group 1 placebo, group 2 fluoride (Elmex fluid), group 3 cerium chloride and group 4 combined fluoride and cerium chloride. For the determination of acid resistance, the samples were consecutively eroded six times for 5 min with lactic acid (pH 3.0) and the calcium release in the acid was determined. Furthermore, six additional samples per group were prepared and used for EDS analysis. SEM pictures of these samples of each group were also captured. Samples of group 1 presented the highest calcium release when compared with the samples of groups 2-4. The highest acid resistance was observed for group 2. Calcium release in group 3 was similar to that of group 4 for the first two erosive attacks, after which calcium release in group 4 was lower than that of group 3. Generally, the SEM pictures showed a surface coating for groups 2-4. No deposits were observed in group 1. Although fluoride showed the best protective effect, cerium chloride was also able to reduce the acid susceptibility of dentine significantly, which merits further investigation. Copyright 2010 Elsevier Ltd. All rights reserved.

  7. Thermal properties of nonstoichiometry uranium dioxide

    Science.gov (United States)

    Kavazauri, R.; Pokrovskiy, S. A.; Baranov, V. G.; Tenishev, A. V.

    2016-04-01

    In this paper, was developed a method of oxidation pure uranium dioxide to a predetermined deviation from the stoichiometry. Oxidation was carried out using the thermogravimetric method on NETZSCH STA 409 CD with a solid electrolyte galvanic cell for controlling the oxygen potential of the environment. 4 samples uranium oxide were obtained with a different ratio of oxygen-to-metal: O / U = 2.002, O / U = 2.005, O / U = 2.015, O / U = 2.033. For the obtained samples were determined basic thermal characteristics of the heat capacity, thermal diffusivity, thermal conductivity. The error of heat capacity determination is equal to 5%. Thermal diffusivity and thermal conductivity of the samples decreased with increasing deviation from stoichiometry. For the sample with O / M = 2.033, difference of both values with those of stoichiometric uranium dioxide is close to 50%.

  8. Toenail cerium levels and risk of a first acute myocardial infarction: The EURAMIC and heavy metals study

    NARCIS (Netherlands)

    Gomez-Aracena, J.; Riemersma, R.A.; Veer, van 't P.; Kok, F.J.

    2006-01-01

    The association between cerium status and risk of first acute myocardial infarction (AMI) was examined in a case-control study in 10 centres from Europe and Israel. Cerium in toenails was assessed by neutron activation analysis in 684 cases and 724 controls aged 70years or younger. Mean concentratio

  9. Effect of Bi content in precursor solutions on microstructure and ferroelectric properties of bismuth cerium titanate thin films

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Sol-gel derived bismuth cerium titanate (BCT) thin films with different Bi contents in precursor solu- tions were deposited on the Pt/Ti/SiO2/Si substrates. The effect of Bi content in the precursor solutions on the microstructure and ferroelectric properties of the films was investigated. It is found that with Bi content increasing from 90% to 110% of the nominal value in the precursor solutions, the dissipation factor and leakage current density of the BCT films obtained decrease, while the grain sizes, dielectric constant and remanent polarizations (2Pr) increase, and concurrently, a Bi-deficient phase of Bi2Ti2O7 gradually disappears. The film prepared from solution with 110% of the nominal Bi content exhibits pure Bi-layered Aurivillius polycrystalline phase, and the 2Pr value and coercive field value are 67.1 μC/cm2 and 299.7 kV/cm, respectively. Their dielectric constant and the dissipation factor are about 172 and 0.033 at 1 kHz, respectively. Moreover, this film shows no polarization fatigue after 4.46×109 switching cycles.

  10. Catalytic properties and biomedical applications of cerium oxide nanoparticles

    KAUST Repository

    Walkey, Carl D.

    2014-11-10

    Cerium oxide nanoparticles (nanoceria) have shown promise as catalytic antioxidants in the test tube, cell culture models and animal models of disease. However given the reactivity that is well established at the surface of these nanoparticles, the biological utilization of nanoceria as a therapeutic still poses many challenges. Moreover the form that these particles take in a biological environment, such as the changes that can occur due to a protein corona, are not well established. This review aims to summarize the existing literature on biological use of nanoceria, and to raise questions about what further study is needed to apply this interesting catalytic material to biomedical applications. These questions include: 1) How does preparation, exposure dose, route and experimental model influence the reported effects of nanoceria in animal studies? 2) What are the considerations to develop nanoceria as a therapeutic agent in regards to these parameters? 3) What biological targets of reactive oxygen species (ROS) and reactive nitrogen species (RNS) are relevant to this targeting, and how do these properties also influence the safety of these nanomaterials?

  11. Anti-angiogenic activity of heparin functionalised cerium oxide nanoparticles.

    Science.gov (United States)

    Lord, Megan S; Tsoi, Bonny; Gunawan, Cindy; Teoh, Wey Yang; Amal, Rose; Whitelock, John M

    2013-11-01

    Cerium oxide nanoparticles (nanoceria) are widely reported to be non-cytotoxic and modulate intracellular reactive oxygen species (ROS). In this study, nanoceria (dxRD = 12 nm) were functionalised with either 130 or 880 molecules of unfractionated heparin using the organosilane linker, 3-aminopropyltriethoxysilane. Nanoceria with a low level of heparin functionalisation were found to scavenge intracellular ROS to the same extent as unfunctionalised nanoceria and significantly more than cells exposed to medium only. In contrast, nanoceria with the highest level of heparin functionalisation were not as effective at scavenging intracellular ROS. Nanoceria were localised predominantly in the cytoplasm, while heparin-nanoceria were localised in both the cytoplasm and lysosomes. Together these data demonstrated that the level of nanoceria surface functionalisation with heparin determined the intracellular localisation and ROS scavenging ability of these particles. Additionally, heparin-nanoceria were effective in reducing endothelial cell proliferation indicating that they may find application in the control of angiogenesis in cancer in the future.

  12. Surface modification of promising cerium oxide nanoparticles for nanomedicine applications

    KAUST Repository

    Nanda, Himansu Sekhar

    2016-11-14

    Cerium oxide nanoparticles (CNPs) or nanoceria have emerged as a potential nanomedicine for the treatment of several diseases such as cancer. CNPs have a natural tendency to aggregate or agglomerate in their bare state, which leads to sedimentation in a biological environment. Since the natural biological environment is essentially aqueous, nanoparticle surface modification using suitable biocompatible hydrophilic chemical moieties is highly desirable to create effective aqueous dispersions. In this report, (6-{2-[2-(2-methoxy-ethoxy)-ethoxy]-ethoxy}-hexyl)triethoxysilane was used as a functional, biocompatible organosilane to modify the surface of CNPs to produce promising nanoparticles which open substantial therapeutic avenues. The surface modified nanoparticles were produced in situ via an ammonia-induced ethylene glycol-assisted precipitation method and were characterized using complimentary characterization techniques. The interaction between the functional moiety and the nanoparticle was studied using powerful cross polarization/magic angle sample spinning solid state nuclear magnetic resonance spectroscopy. The surface-modified nanoparticles were extremely small and demonstrated a significant improvement in aqueous dispersibility. Moreover, the existence of a strong ionic coordination between the functional moiety and the surface of the nanoparticle was realised, indicating that the surface modified nanoceria are stable and that the nanoparticles should demonstrate an enhanced circulation time in a biological environment. The surface modification approach should be promising for the production of CNPs for nanomedicine applications. © The Royal Society of Chemistry.

  13. Antioxidant Cerium Oxide Nanoparticles in Biology and Medicine.

    Science.gov (United States)

    Nelson, Bryant C; Johnson, Monique E; Walker, Marlon L; Riley, Kathryn R; Sims, Christopher M

    2016-05-17

    Previously, catalytic cerium oxide nanoparticles (CNPs, nanoceria, CeO2-x NPs) have been widely utilized for chemical mechanical planarization in the semiconductor industry and for reducing harmful emissions and improving fuel combustion efficiency in the automobile industry. Researchers are now harnessing the catalytic repertoire of CNPs to develop potential new treatment modalities for both oxidative- and nitrosative-stress induced disorders and diseases. In order to reach the point where our experimental understanding of the antioxidant activity of CNPs can be translated into useful therapeutics in the clinic, it is necessary to evaluate the most current evidence that supports CNP antioxidant activity in biological systems. Accordingly, the aims of this review are three-fold: (1) To describe the putative reaction mechanisms and physicochemical surface properties that enable CNPs to both scavenge reactive oxygen species (ROS) and to act as antioxidant enzyme-like mimetics in solution; (2) To provide an overview, with commentary, regarding the most robust design and synthesis pathways for preparing CNPs with catalytic antioxidant activity; (3) To provide the reader with the most up-to-date in vitro and in vivo experimental evidence supporting the ROS-scavenging potential of CNPs in biology and medicine.

  14. Antioxidant Cerium Oxide Nanoparticles in Biology and Medicine

    Directory of Open Access Journals (Sweden)

    Bryant C. Nelson

    2016-05-01

    Full Text Available Previously, catalytic cerium oxide nanoparticles (CNPs, nanoceria, CeO2-x NPs have been widely utilized for chemical mechanical planarization in the semiconductor industry and for reducing harmful emissions and improving fuel combustion efficiency in the automobile industry. Researchers are now harnessing the catalytic repertoire of CNPs to develop potential new treatment modalities for both oxidative- and nitrosative-stress induced disorders and diseases. In order to reach the point where our experimental understanding of the antioxidant activity of CNPs can be translated into useful therapeutics in the clinic, it is necessary to evaluate the most current evidence that supports CNP antioxidant activity in biological systems. Accordingly, the aims of this review are three-fold: (1 To describe the putative reaction mechanisms and physicochemical surface properties that enable CNPs to both scavenge reactive oxygen species (ROS and to act as antioxidant enzyme-like mimetics in solution; (2 To provide an overview, with commentary, regarding the most robust design and synthesis pathways for preparing CNPs with catalytic antioxidant activity; (3 To provide the reader with the most up-to-date in vitro and in vivo experimental evidence supporting the ROS-scavenging potential of CNPs in biology and medicine.

  15. Manifolds of interconvertible pure states

    OpenAIRE

    Sinolecka, Magdalena M.; Zyczkowski, Karol; Kus, Marek

    2001-01-01

    Local orbits of a pure state of an N x N bi-partite quantum system are analyzed. We compute their dimensions which depends on the degeneracy of the vector of coefficients arising by the Schmidt decomposition. In particular, the generic orbit has 2N^2 -N-1 dimensions, the set of separable states is 4(N-1) dimensional, while the manifold of maximally entangled states has N^2-1 dimensions.

  16. Manifolds of interconvertible pure states

    CERN Document Server

    Sinolecka, M M; Kus, M; Sinolecka, Magdalena M.; Zyczkowski, Karol; Kus, Marek

    2002-01-01

    Local orbits of a pure state of an N x N bi-partite quantum system are analyzed. We compute their dimensions which depends on the degeneracy of the vector of coefficients arising by the Schmidt decomposition. In particular, the generic orbit has 2N^2 -N-1 dimensions, the set of separable states is 4(N-1) dimensional, while the manifold of maximally entangled states has N^2-1 dimensions.

  17. Multimedia programming with pure data

    CERN Document Server

    Chung, Bryan

    2013-01-01

    A quick and comprehensive tutorial book for media designers to jump-start interactive multimedia production with computer graphics, digital audio, digital video, and interactivity, using the Pure Data graphical programming environment.An introductory book on multimedia programming for media artists/designers who like to work on interactivity in their projects, digital art/design students who like to learn the first multimedia programming technique, and audio-visual performers who like to customize their performance sets

  18. 电化学阻抗谱法研究铈改性TiO2纳米管阵列光电极裂解水产氢动力学%Dynamics Study on the Cerium and Oxidative Cerium Modified TiO2 Nanotube Arrays for Hydrogen Production by Water Splitting Using Electrochemical Impedance Spectrum

    Institute of Scientific and Technical Information of China (English)

    张胜寒; 梁可心; 檀玉

    2012-01-01

    TiO2 nanotube arrays photoelectrodes were prepared by anode oxidation on pure Ti sheet. The donor material glycol (C2H6O2) added in the anode electrolyte significantly reduced the charge transfer impedance of TiO2 nanotubes to promote the photocatalytic water splitting for hydrogen production. TiO2 nanotube arrays electrodes were modified by cerium and oxidative cerium with electrochemical deposition and anodic oxidation. The fiat band potential moves to the negative potential direction after modification. Electrochemical impedance spectrum (EIS) measurement was used to investigate the electron transfer characteristic in photoelectrodes and the interface characteristic in the photoelectrochemical cell (PEC) for hydrogen production. Arcs of EIS and corresponding electrode processes were discussed. Dynamic parameters of the electrodes were calculated by reasonable electrical equivalent circuit fitting. The results indicate that TiO2 nanotube arrays electrode modified by cerium and oxidative cerium could largely decrease the electron transfer resistance which contributes to hydrogen production. The mechanism of the cerium and oxidative cerium acting on TiO2 nanotube arrays to promote charge transfer is discussed.%通过阳极氧化法在纯钛板上制备TiO2纳米管阵列电极.在光电化学电解池阳极中加入供电子物质乙二醇,显著减小了TiO2纳米管的电荷传递阻抗,促进了光电催化裂解水产氢反应.采用阴极电沉积和阳极氧化法制备了单质铈和氧化铈共同改性的TiO2纳米管阵列半导体光阳极,其平带电位向电负方向移动.采用电化学阻抗谱法(EIS)对改性后TiO2纳米管阵列在光电催化裂解水产氢中的电子传输性能以及界面性质进行了表征,确定了各阻抗弧对应的电极过程.采用合理的等效电路模型计算了电极的电子传输动力学参数.结果表明,经铈改性后的TiO2纳米管阵列膜电阻明显减小,

  19. Self-Correction of Lanthanum-Cerium Halide Gamma Spectra (pre-print)

    Energy Technology Data Exchange (ETDEWEB)

    Ding Yuan, Paul Guss, and Sanjoy Mukhopadhyay

    2009-04-01

    Lanthanum-cerium halide detectors generally exhibit superior energy resolutions for gamma radiation detection compared with conventional sodium iodide detectors. However, they are also subject to self-activities due to lanthanum-138 decay and contamination due to beta decay in the low-energy region and alpha decay in the high-energy region. The detector’s self-activity and crystal contamination jointly contribute a significant amount of uncertainties to the gamma spectral measurement and affect the precision of the nuclide identification process. This paper demonstrates a self-correction procedure for self-activity and contamination reduction from spectra collected by lanthanum-cerium halide detectors. It can be implemented as an automatic self-correction module for the future gamma radiation detector made of lanthanum-cerium halide crystals.

  20. Mesoporous cerium oxide nanospheres for the visible-light driven photocatalytic degradation of dyes

    Directory of Open Access Journals (Sweden)

    Subas K. Muduli

    2014-04-01

    Full Text Available A facile, solvothermal synthesis of mesoporous cerium oxide nanospheres is reported for the purpose of the photocatalytic degradation of organic dyes and future applications in sustainable energy research. The earth-abundant, relatively affordable, mixed valence cerium oxide sample, which consists of predominantly Ce7O12, has been characterized by powder X-ray diffraction, X-ray photoelectron and UV–vis spectroscopy, and transmission electron microscopy. Together with N2 sorption experiments, the data confirms that the new cerium oxide material is mesoporous and absorbs visible light. The photocatalytic degradation of rhodamin B is investigated with a series of radical scavengers, suggesting that the mechanism of photocatalytic activity under visible-light irradiation involves predominantly hydroxyl radicals as the active species.

  1. Oxochloroalkoxide of the Cerium (IV and Titanium (IV as oxides precursor

    Directory of Open Access Journals (Sweden)

    Machado Luiz Carlos

    2002-01-01

    Full Text Available The Cerium (IV and Titanium (IV oxides mixture (CeO2-3TiO2 was prepared by thermal treatment of the oxochloroisopropoxide of Cerium (IV and Titanium (IV. The chemical route utilizing the Cerium (III chloride alcoholic complex and Titanium (IV isopropoxide is presented. The compound Ce5Ti15Cl16O30 (iOPr4(OH-Et15 was characterized by elemental analysis, FTIR and TG/DTG. The X-ray diffraction patterns of the oxides resulting from the thermal decomposition of the precursor at 1000 degreesC for 36 h indicated the formation of cubic cerianite (a = 5.417Å and tetragonal rutile (a = 4.592Å and (c = 2.962 Å, with apparent crystallite sizes around 38 and 55nm, respectively.

  2. Excitation induced spectroscopic study and quenching effect in cerium samarium codoped lithium aluminoborate glasses

    Science.gov (United States)

    Kaur, Parvinder; Kaur, Simranpreet; Singh, Gurinder Pal; Arora, Deepawali; Kumar, Sunil; Singh, D. P.

    2016-08-01

    Lithium aluminium borate host has been codoped with cerium and samarium to prepare glass by conventional melt quench technique. Their structural and spectroscopic investigation has been carried out using XRD, FTIR and density measurements. The UV-Vis absorption spectra and fluorescence spectra (λexc.=380 nm and 400 nm) have been studied for spectroscopic analysis. The amorphous nature of the prepared samples is shown by XRD. The density is increasing with addition of cerium at the expense of aluminium, keeping other components constant. FTIR study also shows the presence of compact and stable tetrahedral BO4 units thus supporting the density results. The UV- Vis absorption spectra show a shift of optical absorption edge towards longer wavelength along with an increase in intensity of peaks with rising samarium concentration. The fluorescence spectra show a blue shift and subsequent suppression of cerium peaks with addition of samarium.

  3. Structure, Morphology and Reducibility of Epitaxial Cerium Oxide Ultrathin Films and Nanostructures

    Directory of Open Access Journals (Sweden)

    Paola Luches

    2015-08-01

    Full Text Available Cerium oxide is a very interesting material that finds applications in many different fields, such as catalysis, energy conversion, and biomedicine. An interesting approach to unravel the complexity of real systems and obtain an improved understanding of cerium oxide-based materials is represented by the study of model systems in the form of epitaxial ultrathin films or nanostructures supported on single crystalline substrates. These materials often show interesting novel properties, induced by spatial confinement and by the interaction with the supporting substrate, and their understanding requires the use of advanced experimental techniques combined with computational modeling. Recent experimental and theoretical studies performed within this field are examined and discussed here, with emphasis on the new perspectives introduced in view of the optimization of cerium oxide-based materials for application in different fields.

  4. The role of chemical interactions between thorium, cerium, and lanthanum in lymphocyte toxicity.

    Science.gov (United States)

    Oliveira, Monica S; Duarte, Isabelle M; Paiva, Amanda V; Yunes, Samira N; Almeida, Carlos E; Mattos, Rita C; Sarcinelli, Paula N

    2014-01-01

    Thorium, cerium, and lanthanum are metals present in several types of minerals, the most common of which is monazite. Cerium and lanthanum are elements in the lanthanides series. Thorium, an actinide metal, is a hazardous element due to its radioactive characteristics. There is a lack of information describing the possible chemical interactions among these elements and the effects they may have on humans. Toxicological analyses were performed using cell viability, cell death, and DNA damage assays. Chemical interactions were evaluated based on the Loewe additivity model. The results indicate that thorium and cerium individually have no toxic effects on lymphocytes. However, thorium associated with lanthanum increases the toxicity of this element, thereby reducing the viability of lymphocytes at low concentrations of metals in the mixture.

  5. Effect of Impurities and Cerium on Stress Concentration Sensitivity of Al-Li Based Alloys

    Institute of Scientific and Technical Information of China (English)

    孟亮; 田丽

    2002-01-01

    A notch sensitivity factor was derived in order to evaluate the stress concentration sensitivity of Al-Li based alloys. The factor values for the Al-Li alloy sheets containing various contents of impurities and cerium addition were evaluated by determining the mechanical properties. It is found that the impurities Fe, Si, Na and K significantly enhance the stress concentration sensitivity of the alloys 2090 and 8090, whereas cerium addition reduces the stress concentration sensitivity to a certain degree for the high strength alloys. However, an excess amount of cerium addition in the high ductility alloy 1420 can significantly increase the stress concentration sensitivity. As compared with conventional aluminum alloys, the Al-Li based alloys generally show high stress concentration sensitivity. Therefore, a special attention must be paid to this problem in the practical application of Al-Li based alloys.

  6. Excitation induced spectroscopic study and quenching effect in cerium samarium codoped lithium aluminoborate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Kaur, Parvinder; Kaur, Simranpreet [Department of Physics, Guru Nanak Dev University, Amritsar 143005 (India); Singh, Gurinder Pal [Department of Physics, Khalsa College, Amritsar 143002 (India); Arora, Deepawali; Kumar, Sunil [Department of Physics, Guru Nanak Dev University, Amritsar 143005 (India); Singh, D.P., E-mail: dpsinghdr@yahoo.com [Department of Physics, Guru Nanak Dev University, Amritsar 143005 (India)

    2016-08-15

    Lithium aluminium borate host has been codoped with cerium and samarium to prepare glass by conventional melt quench technique. Their structural and spectroscopic investigation has been carried out using XRD, FTIR and density measurements. The UV‐Vis absorption spectra and fluorescence spectra (λ{sub exc}.=380 nm and 400 nm) have been studied for spectroscopic analysis. The amorphous nature of the prepared samples is shown by XRD. The density is increasing with addition of cerium at the expense of aluminium, keeping other components constant. FTIR study also shows the presence of compact and stable tetrahedral BO{sub 4} units thus supporting the density results. The UV‐ Vis absorption spectra show a shift of optical absorption edge towards longer wavelength along with an increase in intensity of peaks with rising samarium concentration. The fluorescence spectra show a blue shift and subsequent suppression of cerium peaks with addition of samarium.

  7. Study of phase transitions in cerium in shock-wave experiments

    Directory of Open Access Journals (Sweden)

    Zhernokletov M.V.

    2015-01-01

    Full Text Available Cerium has a complex phase diagram that is explained by the presence of structure phase transitions. Planar gauges were used in various combinations in experiments for determination of sound velocity dependence on pressure in cerium by the technique of PVDF gauge. The data of time dependence on pressure profiles with use of x(t diagrams and the D(u relation for cerium allowed the definition of the Lagrangian velocity of the unloading wave CLagr and the Eulerian velocity CEul by taking into account the compression σ. These results accords with data obtained by using the technique of VISAR and a manganin-based gauge, and calculated pressure dependence of isentropic sound velocity according to the VNIITF EOS. Metallography analysis of post-experimental samples did not find any changes in a phase composition.

  8. KINETIC AND MECHANISTIC STUDY OF OXIDATION OF ATENOLOL BY CERIUM (IV IN SULPHURIC ACIDIC MEDIUM

    Directory of Open Access Journals (Sweden)

    Fadnis G Anand

    2012-03-01

    Full Text Available The kinetics of oxidation of antihypertensive drug, atenolol by cerium (IV in sulphuric acidic medium has been studied spectrophotometrically at 360 nm. The reaction between cerium (IV and atenolol in acidic medium has exhibited 2:1 stoichiometry. The order of the reaction with respect to atenolol has been found to be one. The observed pseudo first order rate constants kobs increased with sulphuric acid and hydrogen ion concentrations where as decreased bisulphate ion concentration indicating the formation bisulphato reactive species of cerium (IV in the present reaction. The thermodynamic parameters have been evaluated from the temperature variation kinetic data. A possible mechanism is proposed which has been validated by derived rate law. An attempt has been made to use rate data for kinetic estimation of atenolol.KEYWORDS:

  9. Samarium Doped Cerium Oxide Clusters: a Study on the Modulation of Electronic Structure

    Science.gov (United States)

    Topolski, Josey E.; Kafader, Jared O.; Marrero-Colon, Vicmarie; Chick Jarrold, Caroline

    2017-06-01

    Cerium oxide is known for its use in solid oxide fuel cells due to its high ionic conductivity. The doping of trivalent samarium atoms into cerium oxide is known to enhance the ionic conductivity through the generation of additional oxygen vacancies. This study probes the electronic structure of Sm_{x}Ce_{y}O_{z} (x+y=3, z=2-4) anion and neutral clusters. Anion photoelectron spectra of these mixed metal clusters exhibit additional spectral features not present in the previously studied cerium oxide clusters. Density functional theory calculations have been used to aid interpretation of collected spectra. The results of this work can be used to inform the design of materials used for solid oxide fuel cells.

  10. Experimental Investigations on the Effects of Cerium Oxide Nanoparticle Fuel Additives on Biodiesel

    Directory of Open Access Journals (Sweden)

    V. Sajith

    2010-01-01

    Full Text Available This paper reports the results of experimental investigations on the influence of the addition of cerium oxide in the nanoparticle form on the major physicochemical properties and the performance of biodiesel. The physicochemical properties of the base fuel and the modified fuel formed by dispersing the catalyst nanoparticles by ultrasonic agitation are measured using ASTM standard test methods. The effects of the additive nanoparticles on the individual fuel properties, the engine performance, and emissions are studied, and the dosing level of the additive is optimized. Comparisons of the performance of the fuel with and without the additive are also presented. The flash point and the viscosity of biodiesel were found to increase with the inclusion of the cerium oxide nanoparticles. The emission levels of hydrocarbon and NOx are appreciably reduced with the addition of cerium oxide nanoparticles.

  11. Luminescence properties and decay kinetics of nano ZnO powder doped with cerium ions

    Energy Technology Data Exchange (ETDEWEB)

    Panda, Nihar Ranjan, E-mail: nihar@iitbbs.ac.in [Indian Institute of Technology Bhubaneswar, Bhubaneswar 751013, Orissa (India); Acharya, B.S., E-mail: bsacharya1950@gmail.com [Department of Physics, C.V. Raman College of Engineering, Bhubaneswar 752054, Orissa (India); Singh, Th. Basanta [Luminescence Dating Laboratory, Manipur University, Imphal 795003 (India); Gartia, R.K. [Department of Physics, Manipur University, Imphal 795003 (India)

    2013-04-15

    ZnO nanopowders doped with cerium ions (1.2 and 1.5 at. wt.%) were synthesized through soft solution route using ultrasound. Sonication has been found to be an effective way for doping rare earth ions like cerium into ZnO. This was confirmed from energy dispersive analysis of X-rays (EDAX) measurement. Further, optical absorption and photoluminescence (PL) measurements corroborate this finding. X-ray diffraction (XRD) studies show the increase of crystallite size and unit cell volume with doping of cerium ions. Formation of fibrous structure of ZnO:Ce was observed from the transmission electron microscopy (TEM) measurements. Although the structural measurements indicate Ce{sup 4+} ion occupying substitutional site in ZnO, PL and absorption studies confirmed the presence of Ce{sup 3+} ion in the powder. The coexistence of Ce{sup 3+} and Ce{sup 4+} ions has been explained on the basis of conversion of Ce{sup 3+} to Ce{sup 4+} in the oxidizing environment. Thermoluminescence (TL) and photo-stimulated decay of luminescence (PSDL) decay studies give an idea of various trapping levels present in the band gap of ZnO. These traps release electrons during optical stimulation to give bimolecular kinetics in nano ZnO:Ce powders. -- Highlights: ► Sonication: an effective way of incorporation of cerium ions into ZnO. ► Site dependent characteristic emission of cerium. ► Energy transfer from host lattice to cerium ions. ► Mono and bimolecular kinetics of ZnO:Ce.

  12. Exposure of cerium oxide nanoparticles to kidney bean shows disturbance in the plant defense mechanisms

    Energy Technology Data Exchange (ETDEWEB)

    Majumdar, Sanghamitra [Department of Chemistry, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN) (United States); Peralta-Videa, Jose R. [Department of Chemistry, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); Environmental Science and Engineering PhD Program, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN) (United States); Bandyopadhyay, Susmita [Environmental Science and Engineering PhD Program, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN) (United States); Castillo-Michel, Hiram [European Synchrotron Radiation Facility, B.P. 220-38043 Grenoble, Cedex (France); Hernandez-Viezcas, Jose-Angel [Department of Chemistry, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN) (United States); Sahi, Shivendra [Department of Biology, Western Kentucky University, Bowling Green, KY 42101 (United States); Gardea-Torresdey, Jorge L., E-mail: jgardea@utep.edu [Department of Chemistry, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); Environmental Science and Engineering PhD Program, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN) (United States)

    2014-08-15

    Graphical abstract: - Highlights: • Kidney bean roots uptake nCeO{sub 2} primarily without biotransformation. • Cerium reached the root vascular tissues through gaps in the Casparian strip. • On longer exposure to high concentration, roots demonstrate stress response. • In leaves, guaiacol peroxidase plays a major role in ROS scavenging. - Abstract: Overwhelming use of engineered nanoparticles demands rapid assessment of their environmental impacts. The transport of cerium oxide nanoparticles (nCeO{sub 2}) in plants and their impact on cellular homeostasis as a function of exposure duration is not well understood. In this study, kidney bean plants were exposed to suspensions of ∼8 ± 1 nm nCeO{sub 2} (62.5 to 500 mg/L) for 15 days in hydroponic conditions. Plant parts were analyzed for cerium accumulation after one, seven, and 15 days of nCeO{sub 2} exposure. The primary indicators of stress like lipid peroxidation, antioxidant enzyme activities, total soluble protein and chlorophyll contents were studied. Cerium in tissues was localized using scanning electron microscopy and synchrotron μ-XRF mapping, and the chemical forms were identified using μ-XANES. In the root epidermis, cerium was primarily shown to exist as nCeO{sub 2}, although a small fraction (12%) was biotransformed to Ce(III) compound. Cerium was found to reach the root vascular tissues and translocate to aerial parts with time. Upon prolonged exposure to 500 mg nCeO{sub 2}/L, the root antioxidant enzyme activities were significantly reduced, simultaneously increasing the root soluble protein by 204%. In addition, leaf's guaiacol peroxidase activity was enhanced with nCeO{sub 2} exposure in order to maintain cellular homeostasis.

  13. Homoleptic cerium(III) and cerium(IV) nitroxide complexes: significant stabilization of the 4+ oxidation state.

    Science.gov (United States)

    Bogart, Justin A; Lewis, Andrew J; Medling, Scott A; Piro, Nicholas A; Carroll, Patrick J; Booth, Corwin H; Schelter, Eric J

    2013-10-07

    Electrochemical experiments performed on the complex Ce(IV)[2-((t)BuNO)py]4, where [2-((t)BuNO)py](-) = N-tert-butyl-N-2-pyridylnitroxide, indicate a 2.51 V stabilization of the 4+ oxidation state of Ce compared to [(n)Bu4N]2[Ce(NO3)6] in acetonitrile and a 2.95 V stabilization compared to the standard potential for the ion under aqueous conditions. Density functional theory calculations suggest that this preference for the higher oxidation state is a result of the tetrakis(nitroxide) ligand framework at the Ce cation, which allows for effective electron donation into, and partial covalent overlap with, vacant 4f orbitals with δ symmetry. The results speak to the behavior of CeO2 and related solid solutions in oxygen uptake and transport applications, in particular an inherent local character of bonding that stabilizes the 4+ oxidation state. The results indicate a cerium(IV) complex that has been stabilized to an unprecedented degree through tuning of its ligand-field environment.

  14. Feasibility of Substituting Cerium-Rich Metal by La-Pr-Ce Alloy in Magnesium Alloy

    Institute of Scientific and Technical Information of China (English)

    伏思静; 赵平

    2004-01-01

    In magnesium alloy ZM3, using cheap Lanthanum-praseodymium-cerium (LPC) rare earth as a substitute for rich-cerium rare earth was studied. The experimental results show that when the adding amount of LPC is between 2.53% and 3.33%, the tensile strength increases as the adding amount of LPC increases; when the amount of RE is 2.53% and 3.33%, the average tensile strength is 142.35, 153.65 MPa respectively. The results show that LPC rare earth replacing rich Ce rare earth is feasible for the tensile strength of ZM3.

  15. Effects of cerium salts on corrosion behaviors of Si–Zr hybrid sol–gel coatings

    OpenAIRE

    Yu Mei; Liu Yuxing; Liu Jianhua; Li Songmei; Xue Bing; Zhang You; Yin Xiaolin

    2015-01-01

    The present work examines the effects of cerium salts on corrosion behaviors of Si–Zr hybrid sol–gel coatings. The Si–Zr hybrid sol–gel coatings on a 2A12 aluminum substrate were prepared through hydrolysis and condensation of glycidoxypropyl-trimethoxy-silane (GTMS) and zirconium(IV) n-propoxide (TPOZ). Used as inhibitors for corrosion, three types of cerium salts (Ce(NO3)3, CeCl3, and Ce(CH3COO)3) were doped into the sol–gel coatings. Fourier transform infrared (FTIR) and scanning electron ...

  16. Dissociation of outer membrane for Escherichia coli cell caused by cerium nitrate

    Institute of Scientific and Technical Information of China (English)

    陈爱美; 施庆珊; 冯劲; 欧阳友生; 陈仪本; 谭绍早

    2010-01-01

    The biological effect of cerium nitrate on the outer membrane(OM) of Escherichia coli(E.coli) cell was studied,and the antim-icrobial mechanism of rare earth elements was explored.The antimicrobial effect of cerium nitrate on E.coli cell was valued by plate count method,and the morphology change of E.coli cell was observed with scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The results showed that the E.coli cell suspension was flocculated when the concentration of Ce(NO3)3?6H2O...

  17. Synthesis and characterization of two dimensional metal organic framework of cerium with tetraaza macrocyclic

    Energy Technology Data Exchange (ETDEWEB)

    Bt Safiin, Nurul Atikah; Yarmo, Ambar; Yamin, Bohari M. [School of Chemical Science and Food Technology. Faculty Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor Darul Ehsan (Malaysia)

    2013-11-27

    A two dimensional metal organic framework containing cerium sufate layers and ethylenediaminium between layers was obtained by refluxing the mixture of cerium sulphate and 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetraazacyclotetradeca-7, 14-diene bromide. The complex was characterized by infrared spectroscopy and microelemental analysis. X-ray study showed that the complex adopts eleven coordination environments about the central atom. Thermogravimetric study showed the removal of water molecules at about 70°C followed by a gradual mass loss until the whole structure collapsed at about 400°C.

  18. Cerium: catalytic properties, technological and environmental applications; Cerio: propriedades cataliticas, aplicacoes tecnologicas e ambientais

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Tereza S. [Universidade de Sao Paulo (USP), SP (Brazil). Inst. de Fisica; Hewer, Thiago L.R. [Universidade de Sao Paulo (USP), SP (Brazil). Inst. de Quimica; Freire, Renato S. [Universidade de Sao Paulo (USP), Cubatao (Brazil). Centro de Capacitacao e Pesquisa em Meio Ambiente]. E-mail: tmartins@if.usp.br

    2007-07-01

    Cerium based-compounds have great importance in a wide range of technological applications, such as: fuel cell devices development; metallurgic processes, petroleum refining; glass and ceramic production. Recently, its catalytic properties have been also explored for environmental applications, especially those to prevent or to control atmospheric and water pollution. Subjects covered in this work include a brief description of the fundaments of cerium catalytic properties and some relevant technological applications. Special attention is given to its photo catalytic activity and its ability to degrade pollutants. Recent results and future prospect about these applications are also evaluated. (author)

  19. A corrosion resistant cerium oxide based coating on aluminum alloy 2024 prepared by brush plating

    Energy Technology Data Exchange (ETDEWEB)

    Tang Junlei; Han Zhongzhi [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Zuo Yu, E-mail: zuoy@mail.buct.edu.cn [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Tang Yuming [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China)

    2011-01-15

    Cerium oxide based coatings were prepared on AA2024 Al alloy by brush plating. The characteristic of this technology is that hydrogen peroxide, which usually causes the plating solution to be unstable, is not necessary in the plating electrolyte. The coating showed laminated structures and good adhesive strength with the substrate. X-ray diffraction and X-ray photoelectron spectroscopy analysis showed that the coatings were composed of Ce(III) and Ce(IV) oxides. The brush plated coatings on Al alloys improved corrosion resistance. The influence of plating parameters on structure and corrosion resistance of the cerium oxide based coating was studied.

  20. Synthesis and characterization of two dimensional metal organic framework of cerium with tetraaza macrocyclic

    Science.gov (United States)

    Bt Safiin, Nurul Atikah; Yarmo, Ambar; Yamin, Bohari M.

    2013-11-01

    A two dimensional metal organic framework containing cerium sufate layers and ethylenediaminium between layers was obtained by refluxing the mixture of cerium sulphate and 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetraazacyclotetradeca-7, 14-diene bromide. The complex was characterized by infrared spectroscopy and microelemental analysis. X-ray study showed that the complex adopts eleven coordination environments about the central atom. Thermogravimetric study showed the removal of water molecules at about 70°C followed by a gradual mass loss until the whole structure collapsed at about 400°C.

  1. Evaluation of Antiproliferative Potential of Cerium Oxide Nanoparticles on HeLa Human Cervical Tumor Cell

    Directory of Open Access Journals (Sweden)

    Zoriţa Diaconeasa

    2015-05-01

    Full Text Available Cerium oxide nanoparticles (CeO2 nanoparticles as nanomaterials have promising biomedical applications. In this paper, the cytotoxicity induced by CONPs human cervical tumor cells was investigated. Cerium oxide nanoparticles were synthesized using the precipitation method. The nanoparticles were found to inhibit the proliferation of HeLa human cervical tumor cells in a dose dependent manner but did not showed to be cytotoxic as analyzed by MTT assay. The administrated treatment decreased the HeLa cell viability cells from 100% to 65% at the dose of 100 μg/mL.

  2. Molecular simulation investigation into the performance of Cu-BTC metal-organic frameworks for carbon dioxide-methane separations

    NARCIS (Netherlands)

    Gutiérrez-Sevillano, J.J.; Caro-Pérez, A.; Dubbeldam, D.; Calero, S.

    2011-01-01

    We report a molecular simulation study for Cu-BTC metal-organic frameworks as carbon dioxide-methane separation devices. For this study we have computed adsorption and diffusion of methane and carbon dioxide in the structure, both as pure components and mixtures over the full range of bulk gas compo

  3. Low Temperature Constrained Sintering of Cerium Gadolinium OxideFilms for Solid Oxide Fuel Cell Applications

    Energy Technology Data Exchange (ETDEWEB)

    Nicholas, Jason Dale [Univ. of California, Berkeley, CA (United States)

    2007-01-01

    Cerium gadolinium oxide (CGO) has been identified as an acceptable solid oxide fuel cell (SOFC) electrolyte at temperatures (500-700 C) where cheap, rigid, stainless steel interconnect substrates can be used. Unfortunately, both the high sintering temperature of pure CGO, >1200 C, and the fact that constraint during sintering often results in cracked, low density ceramic films, have complicated development of metal supported CGO SOFCs. The aim of this work was to find new sintering aids for Ce0.9Gd0.1O1.95, and to evaluate whether they could be used to produce dense, constrained Ce0.9Gd0.1O1.95 films at temperatures below 1000 C. To find the optimal sintering aid, Ce0.9Gd0.1O1.95 was doped with a variety of elements, of which lithium was found to be the most effective. Dilatometric studies indicated that by doping CGO with 3mol% lithium nitrate, it was possible to sinter pellets to a relative density of 98.5% at 800 C--a full one hundred degrees below the previous low temperature sintering record for CGO. Further, it was also found that a sintering aid's effectiveness could be explained in terms of its size, charge and high temperature mobility. A closer examination of lithium doped Ce0.9Gd0.1O1.95 indicated that lithium affects sintering by producing a Li2O-Gd2O3-CeO2 liquid at the CGO grain boundaries. Due to this liquid phase sintering, it was possible to produce dense, crack-free constrained films of CGO at the record low temperature of 950 C using cheap, colloidal spray deposition processes. This is the first time dense constrained CGO films have been produced below 1000 C and could help commercialize metal supported ceria based solid oxide fuel cells.

  4. Universality in pure gravity mediation

    Energy Technology Data Exchange (ETDEWEB)

    Evans, Jason L.; Olive, Keith A. [University of Minnesota, William I. Fine Theoretical Physics Institute, School of Physics and Astronomy, Minneapolis, MN (United States); Ibe, Masahiro [University of Tokyo, ICRR, Kashiwa (Japan); University of Tokyo, Kavli IPMU, TODIAS, Kashiwa (Japan); Yanagida, Tsutomu T. [University of Tokyo, Kavli IPMU, TODIAS, Kashiwa (Japan)

    2013-07-15

    If low-energy supersymmetry is realized in nature, the apparent discovery of a Higgs boson with mass around 125 GeV suggests a supersymmetric mass spectrum in the TeV or multi-TeV range. Multi-TeV scalar masses are a necessary component of supersymmetric models with pure gravity mediation or in any model with strong moduli stabilization. Here, we show that full scalar mass universality remains viable as long as the ratio of Higgs vevs, tan{beta}, is relatively small (

  5. Toxicological evaluation of pure hydroxytyrosol.

    Science.gov (United States)

    Auñon-Calles, David; Canut, Lourdes; Visioli, Francesco

    2013-05-01

    Of all the phenolic constituents of olives and extra virgin olive oil, hydroxytyrosol is currently being actively exploited as a potential supplement or preservative to be employed in the nutraceutical, cosmeceutical, and food industry. In terms of safety profile, hydroxytyrosol has only been investigated as the predominant part of raw olive mill waste water extracts, due to the previous unavailability of appropriate quantities of the pure compound. We report the toxicological evaluation of hydroxytyrosol and, based on the results, propose a No Observed Adverse Effects Level (NOAEL) of 500mg/kg/d.

  6. Synthesis of Enantiomerically Pure Anthracyclinones

    Science.gov (United States)

    Achmatowicz, Osman; Szechner, Barbara

    The anthracycline antibiotics are among the most important clinical drugs used in the treatment of human cancer. The search for new agents with improved therapeutic efficacy and reduced cardiotoxicity stimulated considerable efforts in the synthesis of new analogues. Since the biological activity of anthracyclines depends on their natural absolute configuration, various strategies for the synthesis of enantiomerically pure anthracyclinones (aglycones) have been developed. They comprise: resolution of racemic intermediate, incorporation of a chiral fragment derived from natural and non-natural chiral pools, asymmetric synthesis with the use of a chiral auxiliary or a chiral reagent, and enantioselective catalysis. Synthetic advances towards enantiopure anthracyclinones reported over the last 17 years are reviewed.

  7. Cerium-based conversion coatings on magnesium alloys

    Science.gov (United States)

    Castano Londono, Carlos Eduardo

    This research is primarily focused on gaining a better understanding of the deposition and corrosion behavior of cerium-based conversion coatings (CeCCs) on AZ31B and AZ91D Mg alloys. Deposition of homogenous and protective CeCCs was highly dependent on the surface preparation steps. The best results were obtained when Mg samples underwent grinding, acid cleaning, and alkaline cleaning processes. This reduced the number of active cathodic sites and promoted the formation of a protective Al-rich Mg oxide/hydroxide layer. Electrochemical properties of the CeCCs were also strongly correlated with morphological, microstructural, and chemical characteristics. Protective CeCCs were deposited on both AZ31 and AZ91 Mg alloys using a range of deposition times (5 to 180 s) and temperatures (10 to 80 °C). However, shorter deposition times (5 s) and lower deposition temperatures (~10 °C) showed higher impedance and longer bath stability than other deposition conditions. The increase in impedance was related with fewer cracks and smaller nodule sizes. Additional investigations of post-treated CeCCs exposed to NaCl environments showed an increased in the total impedance. The increase in corrosion protection of the CeCCs was associated with an overall increase in coating thickness from 400 to 800 nm. A microstructural evolution from ~3 nm nodular nanocrystals of CeO2/CePO4*H2O embedded in an amorphous matrix to >50 nm CePO4*H2O nanocrystals was responsible for the electrochemically active corrosion protection. Exposure of CeCCs to sunlight in humid environments promoted the reduction of Ce(IV) into Ce(III) species compared to unexposed coatings. This reduction process was related with photocatalytic water oxidation reaction.

  8. Variations in Reactivity on Different Crystallographic Orientations of Cerium Oxide

    Energy Technology Data Exchange (ETDEWEB)

    Mullins, David R [ORNL; Albrecht, Peter M [ORNL; Calaza, Florencia C [ORNL

    2013-01-01

    Cerium oxide is a principal component in many heterogeneous catalytic processes. One of its key characteristics is the ability to provide or remove oxygen in chemical reactions. The different crystallographic faces of ceria present significantly different surface structures and compositions that may alter the catalytic reactivity. The structure and composition determine the number of coordination vacancies surrounding surface atoms, the availability of adsorption sites, the spacing between adsorption sites and the ability to remove O from the surface. To investigate the role of surface orientation on reactivity, CeO2 films were grown with two different orientations. CeO2(100) films were grown ex situ by pulsed laser deposition on Nb-doped SrTiO3(100). CeO2(111) films were grown in situ by thermal deposition of Ce metal onto Ru(0001) in an oxygen atmosphere. The chemical reactivity was characterized by the adsorption and decomposition of various molecules such as alcohols, aldehydes and organic acids. In general the CeO2(100) surface was found to be more active, i.e. molecules adsorbed more readily and reacted to form new products, especially on a fully oxidized substrate. However the CeO2(100) surface was less selective with a greater propensity to produce CO, CO2 and water as products. The differences in chemical reactivity are discussed in light of possible structural terminations of the two surfaces. Recently nanocubes and nano-octahedra have been synthesized that display CeO2(100) and CeO2(111) faces, respectively. These nanoparticles enable us to correlate reactions on high surface area model catalysts at atmospheric pressure with model single crystal films in a UHV environment.

  9. Thermoluminescence of cerium and terbium -doped calcium pyrophosphate

    Energy Technology Data Exchange (ETDEWEB)

    Roman L, J.; Cruz Z, E. [UNAM, Instituto de Ciencias Nucleares, Circuito Exterior, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Lozano R, I. B.; Diaz G, J. A. I., E-mail: jesus.roman@nucleares.unam.mx [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Av. Legaria No. 694, 11500 Mexico D. F. (Mexico)

    2015-10-15

    The aim of this work is to report the thermoluminescence (Tl) response of Calcium Pyrophosphate phosphor doped with Cerium and Terbium impurities (Ca{sub 2}P{sub 2}O{sub 7}:Ce{sup 3+},Tb{sup 3+}). The phosphors were synthesized using the co-precipitation method and annealed at 900 degrees C by two hours for obtain the β phase. The intentional doping with Ce and Tb ions was 1 at.% and 0.1 at.%, whereas in the EDS results the concentration of impurities was 0.39 at.% and 0.05 at.%, respectively. The superficial morphology of phosphor is mainly composed by thin wafers of different size. All samples were exposed to gamma rays from {sup 60}Co in the Gammacell-200 irradiator. The Tl response of the phosphor was measured from Rt up to 350 degrees C and under nitrogen atmosphere in a Harshaw TLD 3500 reader. The glow curves of the Ca{sub 2}P{sub 2}O{sub 7}:Ce{sup 3+},Tb{sup 3+} powders showed a broad intense Tl peak centered at 165 degrees C and a shoulder at approximate 260 degrees C was observed. A linear Tl response in the range of absorbed dose of 0.2 to 10 Gy was obtained. Tl glow curves were analyzed using the initial rise (IR)and computerized glow curve deconvolution methods to evaluate the kinetics parameters such as activation energy (E), frequency factor (s) and kinetic order (b). (Author)

  10. Gas sensing behaviour of cerium oxide and magnesium aluminate composites

    Indian Academy of Sciences (India)

    N NITHYAVATHY; V RAJENDRAN; L JOHN BERCHMANS; M MAAZA; S KRITHIKA; S ARUNMETHA

    2017-08-01

    Composites of cerium oxide (CeO$_2$) and magnesium aluminate (MgAl$_2$O$_4$) were prepared by the moltensalt synthesis (MSS) method at 1130 K. The composite samples were named as MA, MAC0.07 and MAC0.14 (at CeO$_2$:0, 0.07 and 0.14 g in MgAl$_2$O$_4$, respectively) and these were characterized by X-ray diffraction and energy-dispersiveX-ray analyses. It is seen that the microstructure of the composite samples are quite similar except for a small increasein particle size. The energy-dispersive X-ray analyses provide the presence of concentration of Ce, Mg, Al and O in thecomposite. Scanning electron microscope, coupled with energy-dispersive X-ray analysis (SEM-EDAX) was used to identifythe morphology, microstructure and elemental composition of the prepared samples. The decomposition and dissociationreactions of the precursors were determined using differential thermal and thermogravimetric analysis (TGA). A lone pairof the electron state was identified from the electro paramagnetic resonance spectrum. An optical energy band gap of 3.3 eV was calculated from the UV–Vis absorbance spectra. The gas response to changes in oxygen (O$_2$), carbon monoxide (CO) (at 0.5, 1.0 and 1.5 bar) and ethanol (at 50 and 100 ppm) was quantitatively analysed in all the samples at differentoperating temperatures (300-500 K). The magnitude of the temperature varied linearly regardless of the gas pressure insidethe chamber, by increasing the supply in the heating pad, mounted below the sensor sample. The composite samples indicatea good response to different gases with detection of the smallest change in gas pressure.

  11. Effects of Cerium Oxide Nanoparticles on Sorghum Plant Traits

    Science.gov (United States)

    Mu, L.; Chen, Y.; Darnault, C. J. G.; Rauh, B.; Kresovich, S.; Korte, C.

    2015-12-01

    Nanotechnology and nanomaterials are considered as the development of the modern science. However, besides with that wide application, nanoparticles arouse to the side effects on the environment and human health. As the catalyst of ceramics and fuel industry, Cerium (IV) oxide nanoparticles (CeO2 NPs) can be found in the environment following their use and life-cycle. Therefore, it is critical to assess the potential effects that CeO2 NPs found in soils may have on plants. In this study, CeO2 NPs were analyzed for the potential influence on the sorghum [Sorghum bicolor (L.) Moench] (Reg. no. 126) (PI 154844) growth and traits. The objectives of this research were to determine whether CeO2 NPs impact the sorghum germination and growth characteristics. The sorghum was grown in the greenhouse located at Biosystems Research Complex, Clemson University under different CeO2 NPs treatments (0mg; 100mg; 500mg; 1000mg CeO2 NPs/Kg soil) and harvested around each month. At the end of the each growing period, above ground vegetative tissue was air-dried, ground to 2mm particle size and compositional traits estimated using near-infrared spectroscopy. Also, the NPK value of the sorghum tissue was tested by Clemson Agriculture Center. After the first harvest, the result showed that the height of above ground biomass under the nanoparticles stress was higher than that of control group. This difference between the control and the nanoparticles treatments was significant (F>F0.05; LSD). Our results also indicated that some of the compositional traits were impacted by the different treatments, including the presence and/or concentrations of the nanoparticles.

  12. Pure dysarthria due to an insular infarction.

    Science.gov (United States)

    Hiraga, Akiyuki; Tanaka, Saiko; Kamitsukasa, Ikuo

    2010-06-01

    Cortical infarction presenting with pure dysarthria is rarely reported. Previous studies have reported pure dysarthria due to cortical stroke at the precentral gyrus or middle frontal gyrus. We report a 72-year-old man who developed pure dysarthria caused by an acute cortical infarction in the insular cortex. The role of the insula in language has been difficult to assess clinically because of the rarity of pure insular strokes. Our patient showed pure dysarthria without aphasia, indicating that pure dysarthria can be the sole manifestation of insular infarctions.

  13. Study of Degradation Kinetics of Parathion Methyl On Mixed Nanocrystalline Titania-Zirconium and Titania-Cerium Oxides

    Science.gov (United States)

    Kuráň, Pavel; Pšenička, Martin; Šťastný, Martin; Benkocká, Monika; Janoš, Pavel

    2016-10-01

    The unique surface properties of some nanocrystalline metal oxides and their application for removal of various toxic compounds were reported in early 1990s. Recently, a reliable method for the preparation of reactive cerium dioxide sorbent and its application for degradation of the organophosphate pesticides, such as parathion methyl, chlorpyrifos, dichlofenthion, fenchlorphos, and prothiofos, as well as of some chemical warfare agents-nerve gases soman and O-ethyl S-[2-(diisopropylamino) ethyl] methylphosphonothioate (VX) was published. This paper reports on the kinetics study of degradation of parathion methyl as a representative organophosphate on nanocrystalline metal oxides TiO2, ZrO2, CeO2 and their mixtures in different molar ratios of particular elements. The tested sorbents except of CeO2 were prepared by different methods (e.g. sol-gel, precipitation) in cooperation with Institute of Inorganic Chemistry (Rez, Czech Republic). The degradation kinetics of parathion methyl on tested sorbents was followed by HPLC equipped with diode array detector. The basic kinetics parameters (half-lives of parathion methyl degradation, rate constants of degradation product formation) were calculated for each sorbent from Weber-Morris equation of 1st order diffusion kinetic model. The results proved the ability of prepared sorbents to degrade parathion methyl under formation of 4-nitrophenol as the main degradation product. The most efficient sorbents were TiCe (2:8), TiCe (1:1), TiCe (0:1) (50-70 %) followed by TiZr (1:1), TiCe (8:2), TiZr (8:2), TiZr (2:8) (20-30%) and TiO2, ZrO2 (less than 5 %).

  14. ABSOLUTELY E-PURE MODULES AND E-PURE SPLIT MODULES

    Institute of Scientific and Technical Information of China (English)

    Yan Hangyu

    2011-01-01

    We first introduce the concepts of absolutely E-pure modules and Epure split modules. Then, we characterize the IF rings in terms of absolutely E-pure modules. The E-pure split modules are also characterized.

  15. Cerium Oxide Nanoparticles and Bulk Cerium Oxide Leading to Different Physiological and Biochemical Responses in Brassica rapa.

    Science.gov (United States)

    Ma, Xingmao; Wang, Qiang; Rossi, Lorenzo; Zhang, Weilan

    2016-07-05

    Cerium oxide nanoparticles (CeO2NPs) have been incorporated into many commercial products, and their potential release into the environment through the use and disposal of these products has caused serious concerns. Despite the previous efforts and rapid progress on elucidating the environmental impact of CeO2NPs, the long-term impact of CeO2NPs to plants, a key component of the ecosystem, is still not well understood. The potentially different impact of CeO2NPs and their bulk counterparts to plants is also unclear. The main objectives of this study were (1) to investigate whether continued irrigation with solutions containing different concentrations of CeO2NPs (0, 10, and 100 mg/L) would induce physiological and biochemical adjustments in Brassica rapa in soil growing conditions and (2) to determine whether CeO2NPs and bulk CeO2 particles exert different impacts on plants. The results indicated that bulk CeO2 at 10 and 100 mg/L enhanced plant biomass by 28% and 35%, respectively, while CeO2NPs at equivalent concentrations did not. While the bulk CeO2 treatment resulted in significantly higher concentrations of hydrogen peroxide (H2O2) in plant tissues at the vegetative stage, CeO2NPs led to significantly higher H2O2 levels in plant tissues at the floral stage. The activity of superoxide dismutase (SOD) in Brassica rapa also displayed a growth-stage dependent response to different sizes of CeO2 while catalase (CAT) activity was not affected by either size of CeO2 throughout the life cycle of Brassica rapa. Altogether, the results demonstrated that plant responses to CeO2 exposure varied with the particle sizes and the growth stages of plants.

  16. Structural and electrochemical studies on the utilization of Cerium (Ce3+ as an additive for nickel hydroxide electrode

    Directory of Open Access Journals (Sweden)

    Marcio Vidotti

    2007-03-01

    Full Text Available This paper describes electrochemical and spectroscopic studies on the utilization of cerium atoms as additives for nickel hydroxide electrodes. Thin films were galvanostatically grown with different amounts of cerium and mixed electrodes were studied by electrochemical measurements and the spectroscopic technique. The electrochromic behavior was investigated by “in situ” experiments , while the amount of species was determined by ICP-OES. The addition of cerium to nickel hydroxide electrodes increases durability, due to modifications in the structural properties, as seen by Raman spectras.

  17. Formation of Self-Assembled Monolayer on Cerium Conversion Coated AZ31 Mg Alloy

    Science.gov (United States)

    Salman, S. A.; Akira, N.; Kuroda, K.; Okido, M.

    Magnesium alloys are recognized as alternatives to Al alloys and steel to reduce the weight of structural materials. However, a major obstacle to the widespread use of magnesium alloys is its poor corrosion resistance. Therefore, further surface treatment of magnesium and its alloy is important in meeting several industrial specifications. In a previous research, we investigated the surface treatment of AZ31 magnesium alloy using cerium conversion coating. The anticorrosion properties could be improved with the cerium treatment. In this present research, self-assembled monolayer (SAM) was adsorbed on the surface of cerium conversion coated AZ31 magnesium alloy. The SAM thin film was deposited using (Tridecafluoro-1, 1, 2, 2-tetrahydrooctyl) trimethoxysilane (FAS13) and Tetrakis(trimethylsiloxy)titanium (TTMS) as a catalyst. The corrosion resistance of cerium conversion coated AZ31 Mg alloy was improved with SAM post treatment. Furthermore, the contact angle increases from 13 deg. to 169 deg. indicating to production of super hydrophobic surface with SAM post treatment.

  18. Characteristics of cerium-gadolinium oxide (CGO) suspensions as a function of dispersant and powder properties

    DEFF Research Database (Denmark)

    Phair, John; Lönnroth, Nadja; Lundberg, Mats;

    2009-01-01

    A series of concentrated suspensions ( = 0.18–0.34) of cerium-gadolinium oxide (CGO) in terpineol were prepared as a function of dispersant, powder surface area and solids concentration. The stability of the suspensions was assessed by rheological measurements including viscosity and oscillatory...

  19. On the synthesis of monopentamethylcyclopentadienyl derivatives of yttrium, lanthanum, and cerium

    NARCIS (Netherlands)

    Booij, Martin; Kiers, Niklaas H.; Heeres, Hero J.; Teuben, Jan H.

    1989-01-01

    Two routes leading to monopentamethylcyclopentadienyl-yttrium, -lanthanum and -cerium complexes have been explored. Transmetallation of LnCl3(THF)x with Cp*Li (Cp* = C5Me5) proved useful only in some particular cases. Acid-base reactions of homoleptic complexes LnR3 with Cp*H generally gave Cp*2LnR

  20. Effects of Cerium on Alloy Elements Distribution in Ferrous Matrix Material

    Institute of Scientific and Technical Information of China (English)

    刘英才; 刘俊友; 尹衍生; 刘国权

    2001-01-01

    The effect of the addition of rare earths in Fe-based high chromium alloy powders on elements distribution in matrix materials and mechanical properties were studied. The results show that the addition of cerium can increase the chromium amount in carbonides and increase the micro-hardness after carbonization and the wear-resistant property of materials.

  1. Transient Dynamics of Fluoride-Based High Concentration Erbium/Cerium Co-Doped Fiber Amplifier

    Institute of Scientific and Technical Information of China (English)

    S. S-H. Yam; Y. Akasaka; Y. Kubota; R. Huang; D. L. Harris; J. Pan

    2003-01-01

    We designed and evaluated a fluoride-based high concentration erbium/ cerium co-doped fiber amplifier. It is suitable for Metropolitan Area Networks due to faster transient, flatter (unfiltered) gain, smaller footprint and gain excursion than its silica-based counterpart.

  2. Synthesis and Characterization of the First Organically Templated Layered Cerium Phosphate Fluoride

    National Research Council Canada - National Science Library

    Ranbo Yu; Dan Wang; Shintaro Ishiwata; Takashi Saito; Masaki Azuma; Mikio Takano; Yunfa Chen; Jinghai Li

    2004-01-01

      A novel organically templated layered cerium phosphate fluoride [(CH2)2(NH3)2]0.5[CeIVF3(HPO4)] has been synthesized by hydrothermal synthesis technology, and characterized by means of single-crystal X-ray diffraction...

  3. Growth and characterization of cerium lanthanum oxalate crystals grown in hydro-silica gel

    Energy Technology Data Exchange (ETDEWEB)

    John, M.V.; Ittyachen, M.A. [Mahatma Gandhi Univ., Kerala (India). School of Pure and Applied Physics

    2001-07-01

    Single crystals of mixed cerium lanthanum oxalate (CLO) are grown by gel method. Over the hydrosilica gel prepared by mixing oxalic acid and sodium meta silicate, a mixture of aqueous solutions of cerium nitrate and lanthanum nitrate are poured gently. Cerium and lanthanum ions diffuse into the gel and react with oxalic acid to give colorless, transparent cerium lanthanum oxalate crystals with in a few days. Different growth parameters give crystals of various dimensions. Infrared (IR) spectrum confirms the presence of water molecules and carboxylic acid. X-ray diffraction (XRD) pattern of these samples reveals the crystalline nature. Diffraction peaks are indexed. Unit cell parameters are determined. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) data support the presence of 9 H{sub 2}O molecules attached to the CLO crystal lattice which are lost around 200 C as revealed by the endotherm record. Exothermic peak around 350 C-425 C shows the release of CO and CO{sub 2}. Elemental analysis done by energy dispersive X-ray fluorescence analysis (EDXRF) for the mixed rare earth compound is almost in good agreement with experimental and theoretical values. (orig.)

  4. Release of cerium dibutylphosphate corrosion inhibitors from highly filled epoxy coating systems

    NARCIS (Netherlands)

    Soestbergen, M. van; Baukh, V.; Erich, S.J.F.; Huinink, H.P.; Adan, O.C.G.

    2014-01-01

    Carcinogenic chromates are phased out as corrosion inhibitors in organic coatings, and are replaced by benign alternatives. Cerium-based compounds are excellent corrosion inhibitors in an aqueous environment. However, whether they are effective as corrosion inhibitor in an organic coating also depen

  5. Titrimetric and Spectrophotometric Methods for the Assay of Ketotifen Using Cerium(IV and Two Reagents

    Directory of Open Access Journals (Sweden)

    Madihalli Srinivas Raghu

    2013-01-01

    Full Text Available One titrimetric and two spectrophotometric methods are described for the determination of ketotifen fumarate (KTF in bulk drug and in tablets using cerium(IV as the oxidimetric agent. In titrimetry (method A, the drug was treated with a measured excess of cerium(IV in H2SO4 medium and after a standing time of 10 min, the surplus oxidant was determined by back titration with iron(II. The spectrophotometric procedures involve addition of a known excess of cerium(IV to KTF in acid medium followed by the determination of unreacted oxidant by reacting with either p-dimethyl amino benzaldehyde and measuring the resulting colour at 460 nm (method B or o-dianisidine and subsequent measurement of the absorbance of coloured product at 470 nm (method C. Titrimetric assay is based on a 1 : 2 reaction stoichiometry between KTF and cerium(IV and the method is applicable over 2–18 mg range. In spectrophotometry, regression analysis of Beer’s law plots showed a good correlation in 0.4–8.0 and 0.4–10.0 g mL−1 KTF ranges for method B and method C, respectively, and the corresponding molar absorptivity coefficients are calculated to be and  L mol−1 cm−1.

  6. Pure optical dynamical color encryption

    Science.gov (United States)

    Mosso, Fabian; Tebaldi, Myrian; Fredy Barrera, John; Bolognini, Néstor; Torroba, Roberto

    2011-07-01

    We introduce a way to encrypt-decrypt a color dynamical phenomenon using a pure optical alternative. We split the three basic chromatic channels composing the input, and then each channel is processed through a 4f encoding method and a theta modulation applied to the each encrypted frame in every channel. All frames for a single channel are multiplexed. The same phase mask is used to encode all the information. Unlike the usual procedure we do not multiplex the three chromatic channels into a single encoding media, because we want to decrypt the information in real time. Then, we send to the decoding station the phase mask and the three packages each one containing the multiplexing of a single channel. The end user synchronizes and decodes the information contained in the separate channels. Finally, the decoding information is conveyed together to bring the decoded dynamical color phenomenon in real-time. We present material that supports our concepts.

  7. 76 FR 69284 - Pure Magnesium From China

    Science.gov (United States)

    2011-11-08

    ... COMMISSION Pure Magnesium From China Determination On the basis of the record \\1\\ developed in the subject... order on pure magnesium from China would be likely to lead to continuation or recurrence of material... USITC Publication 4274 (October 2011), entitled Pure Magnesium from China: Investigation No....

  8. 4d → 4f resonance in photoabsorption of cerium ion Ce3+ and endohedral cerium in fullerene complex {\\rm{Ce}}@{{{\\rm{C}}}_{82}}^{+}

    Science.gov (United States)

    Schrange-Kashenock, G.

    2016-09-01

    The theoretical investigation of the single-photoionization spectra in the 4d-resonance region (120-150 eV) for the ionic cerium Ce3+ and cerium in the endohedral complex {{Ce}}@{{{{C}}}82}+ (in practice, {{{Ce}}}3+@{{{{C}}}82}2-) is presented. The fullerene cage is modeled by ab initio spherical jellium shell with an accurate account for the real distribution of carbon electron density. The oscillator strengths are calculated within the multiconfiguration Dirac-Fock (MCDF) approach for phototransitions from the outermost shells of the ion Ce3+ with and without the influence of the potential generated by a fullerene cage. It is shown that the integrated oscillator strengths have the main contribution from the Ce3+ 4d → 4f (ten possible from the phototransitions {}2F{7/2,5/2}\\to {}2D{3/2,5/2},{}2F{5/2,7/2},{}2G{5/2,7/2}) resonance photoexcitations. The corresponding precise MCDF values for the oscillator strengths and the transition energies are presented for the first time. It is demonstrated that the resonance {f}4d\\to 4f oscillator strengths are slightly affected by the presence of the cage potential, despite the fact that the spectral levels structure is changed when the effect of this potential is included. The Auger 4d -1 decay from the cerium free ion Ce3+ and the encapsulated endohedral ion Ce3+@ are considered within the two-step model and the corresponding Lorentzian profiles are presented. This model clearly reveals the correspondence of the complex resonance profile in the Ce3+ photoabsorption to the fine structure of ion energy levels. The smoothing of the resonance profile in the photoabsorption of the endohedral system {{Ce}}@{{{{C}}}82}+ compared with the free ion Ce3+ is attributed to increasing the linewidths of the Auger transitions. This increase is estimated from the relevant experiment (Müller et al 2008 Phys. Rev. Lett. 101 133001) to be strong; as at least three times the value for an isolated ion. The presence of the confining fullerene

  9. Effect of cerium substitution on structural and magnetic properties of magnetite nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Padalia, Diwakar, E-mail: Padalia.diwakar@gmail.com [Department of Physics, G.B.Pant University of Agriculture & Technology, Pantnagar, Uttrakhand (India); Johri, U.C. [Department of Physics, G.B.Pant University of Agriculture & Technology, Pantnagar, Uttrakhand (India); Zaidi, M.G.H. [Supercritical Fluid Processing Laboratory, Department of Chemistry, G.B.Pant University of Agriculture & Technology, Pantnagar, Uttrakhand (India)

    2016-02-01

    The current work presents the synthesis and properties of cerium doped magnetite (Fe{sub 3}O{sub 4}) nanoparticles synthesized by standard chemical co-precipitation method using NH{sub 4}OH as co-precipitating agent. The effects of cerium ion substitution on structural and magnetic properties of magnetite (Fe{sub 3}O{sub 4}) nanoparticles were reported. These materials were characterized by X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and vibrating sample magnetometer (VSM). The cerium content has a significant influence on structural and magnetic properties. The X-ray diffraction study confirmed the formation of single-phase magnetite with space group Fd3m and crystallite size ranging from 39 to 58 nm. The addition of cerium resulted in a reduction of crystallite size and an increase of cell parameters. FTIR measurements confirmed the formation of different samples and suggested that the reduction of Fe{sup +3} to Fe{sup +2} preferred on a site adjacent to Ce{sup +4}. Magnetic measurements revealed that the saturation magnetization (Ms) and remanence (M{sub r}) decreased while the coercivity (H{sub C}) and squareness (M{sub r}/M{sub S}) increased with increasing cerium content. - Highlights: • There is an increase in cell parameters and strain with Ce-content. • Samples show the presence of secondary phase after 1.0% doping level. • Ce-ions prefer octahedral sites and charge neutrality is accompanied by Fe{sup +3} → Fe{sup +2}. • Magnetization decreases due to weakening of the super exchange interactions. • Squareness and coercivity start to increase with Ce content.

  10. Magnetic hysteresis of cerium doped bismuth ferrite thin films

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, Surbhi [Department of Physics and Astrophysics, University of Delhi (India); Tomar, Monika [Physics Department, Miranda House, University of Delhi (India); Gupta, Vinay, E-mail: drguptavinay@gmail.com [Department of Physics and Astrophysics, University of Delhi (India)

    2015-03-15

    The influence of Cerium doping on the structural and magnetic properties of BiFeO{sub 3} thin films have been investigated. Rietveld refinement of X-ray diffraction data and successive de-convolution of Raman scattering spectra of Bi{sub 1−x}Ce{sub x}FeO{sub 3} (BCFO) thin films with x=0–0.20 reflect the single phase rhombohedral (R3c) formation for x<0.08, whereas concentration-driven gradual structural phase transition from rhombohedral (R3c) to partial tetragonal (P4mm) phase follows for x≥0.08. All low wavenumber Raman modes (<300 cm{sup −1}) showed a noticeable shift towards higher wavenumber with increase in doping concentration, except Raman E-1 mode (71 cm{sup −1}), shows a minor shift. Sudden evolution of Raman mode at 668 cm{sup −1}, manifested as A{sub 1}-tetragonal mode, accompanied by the shift to higher wavenumber with increase in doping concentration (x) affirm partial structural phase transition. Anomalous wasp waist shaped (M–H) hysteresis curves with improved saturation magnetization (M{sub s}) for BCFO thin films is attributed to antiferromagnetic interaction/hybridization between Ce 4f and Fe 3d electronic states. The contribution of both hard and soft phase to the total coercivity is calculated. Polycrystalline Bi{sub 0.88}Ce{sub 0.12}FeO{sub 3} thin film found to exhibit better magnetic properties with M{sub s}=15.9 emu/g without any impure phase. - Highlights: • Synthesis of single phase Bi{sub 1−x}Ce{sub x}FeO{sub 3} thin films with (x=0–0.2) on cost effective corning glass and silicon substrates using CSD technique. • Structural modification studies using Rietveld refinement of XRD and de-convolution of Raman spectra revealed partial phase transition from rhombohedral (R3c) to tetragonal (P4mm) phase. • Possible reasons for origin of pinched magnetic behavior of BCFO thin films are identified. • Contribution of both hard and soft magnetic phase in coercivity of BCFO thin films is calculated and practical

  11. Structural, electronic, and hyperfine properties of pure and Ta-doped m-ZrO2

    DEFF Research Database (Denmark)

    Taylor, M.A.; Alonso, R.E.; Errico, L.A.

    2012-01-01

    A combination of experiments and ab initio quantum-mechanical calculations has been applied to examine electronic, structural, and hyperfine interactions in pure and Ta-doped zirconium dioxide in its monoclinic phase (m-ZrO2). From the theoretical point of view, the full-potential linear augmented...

  12. Near-pure vapor condensation in the Martian atmosphere: CO2 ice crystal growth

    OpenAIRE

    Listowski, Constantino; Määttänen, Anni; Riipinen, Ilona; Montmessin, Franck; Lefèvre, Franck

    2013-01-01

    International audience; A new approach is presented to model the condensational growth of carbon dioxide (CO2) ice crystals on Mars. These condensates form in very particular conditions. First, ~95% of the atmosphere is composed of CO2 so that near-pure vapor condensation takes place. Second, the atmosphere is rarefied, having dramatic consequences on the crystal growth. Indeed, the subsequently reduced efficiency of heat transport helps maintain a high temperature difference between the crys...

  13. Dual Target Search is Neither Purely Simultaneous nor Purely Successive.

    Science.gov (United States)

    Cave, Kyle R; Menneer, Tamaryn; Nomani, Mohammad S; Stroud, Michael J; Donnelly, Nick

    2017-08-31

    Previous research shows that visual search for two different targets is less efficient than search for a single target. Stroud, Menneer, Cave and Donnelly (2012) concluded that two target colours are represented separately based on modeling the fixation patterns. Although those analyses provide evidence for two separate target representations, they do not show whether participants search simultaneously for both targets, or first search for one target and then the other. Some studies suggest that multiple target representations are simultaneously active, while others indicate that search can be voluntarily simultaneous, or switching, or a mixture of both. Stroud et al.'s participants were not explicitly instructed to use any particular strategy. These data were revisited to determine which strategy was employed. Each fixated item was categorised according to whether its colour was more similar to one target or the other. Once an item similar to one target is fixated, the next fixated item is more likely to be similar to that target than the other, showing that at a given moment during search, one target is generally favoured. However, the search for one target is not completed before search for the other begins. Instead, there are often short runs of one or two fixations to distractors similar to one target, with each run followed by a switch to the other target. Thus, the results suggest that one target is more highly weighted than the other at any given time, but not to the extent that search is purely successive.

  14. CARBON DIOXIDE SEPARATION BY SELECTIVE PERMEATION.

    Science.gov (United States)

    CARBON DIOXIDE , SEPARATION), (*PERMEABILITY, CARBON DIOXIDE ), POROUS MATERIALS, SILICON COMPOUNDS, RUBBER, SELECTION, ADSORPTION, TEMPERATURE, PRESSURE, POLYMERS, FILMS, PLASTICS, MEMBRANES, HUMIDITY.

  15. Decryption of pure-position permutation algorithms

    Institute of Scientific and Technical Information of China (English)

    赵晓宇; 陈刚; 张亶; 王肖虹; 董光昌

    2004-01-01

    Pure position permutation image encryption algorithms, commonly used as image encryption investigated in this work are unfortunately frail under known-text attack. In view of the weakness of pure position permutation algorithm,we put forward an effective decryption algorithm for all pure-position permutation algorithms. First, a summary of the pure position permutation image encryption algorithms is given by introducing the concept of ergodic matrices. Then, by using probability theory and algebraic principles, the decryption probability of pure-position permutation algorithms is verified theoretically; and then, by defining the operation system of fuzzy ergodic matrices, we improve a specific decryption al-gorithm. Finally, some simulation results are shown.

  16. Compressibility and structural behavior of pure and Fe-doped SnO2 nanocrystals

    Science.gov (United States)

    Grinblat, F.; Ferrari, S.; Pampillo, L. G.; Saccone, F. D.; Errandonea, D.; Santamaria-Perez, D.; Segura, A.; Vilaplana, R.; Popescu, C.

    2017-02-01

    We have performed high-pressure synchrotron X-ray diffraction experiments on nanoparticles of pure tin dioxide (particle size ∼30 nm) and 10 mol % Fe-doped tin dioxide (particle size ∼18 nm). The structural behavior of undoped tin dioxide nanoparticles has been studied up to 32 GPa, while the Fe-doped tin dioxide nanoparticles have been studied only up to 19 GPa. We have found that both samples present at ∼13 GPa a second-order structural phase transition from the ambient pressure tetragonal rutile-type structure (P42/mnm) to an orthorhombic CaCl2-type structure (space group Pnnm). No phase coexistence was observed for this transition. Additionally, pure SnO2 presents a phase transition to a cubic structure at ∼24 GPa. The evolution of the lattice parameters with pressure and the room-temperature equations of state are reported for the different phases. The reported results suggest that the partial substitution of Sn by Fe induces an enhancement of the bulk modulus of SnO2. Results are compared with previous studies on bulk and nanocrystalline SnO2. The effects of pressure on Sn-O bonds are also analyzed.

  17. Radioactive waste forms stabilized by ChemChar gasification: characterization and leaching behavior of cerium, thorium, protactinium, uranium, and neptunium.

    Science.gov (United States)

    Marrero, T W; Morris, J S; Manahan, S E

    2004-02-01

    The uses of a thermally reductive gasification process in conjunction with vitrification and cementation for the long-term disposal of low level radioactive materials have been investigated. gamma-ray spectroscopy was used for analysis of carrier-free protactinium-233 and neptunium-239 and a stoichiometric amount of cerium (observed cerium-141) subsequent to gasification and leaching, up to 48 days. High resolution ICP-MS was used to analyze the cerium, thorium, and uranium from 46 to 438 days of leaching. Leaching procedures followed the guidance of ASTM Procedure C 1220-92, Standard Test Method for Static Leaching of Monolithic Waste Forms for Disposal of Radioactive Waste. The combination of the thermally reductive pretreatment, vitrification and cementation produced a highly non-leachable form suitable for long-term disposal of cerium, thorium, protactinium, uranium, and neptunium.

  18. Carbon dioxide sensor

    Energy Technology Data Exchange (ETDEWEB)

    Dutta, Prabir K. (Worthington, OH); Lee, Inhee (Columbus, OH); Akbar, Sheikh A. (Hilliard, OH)

    2011-11-15

    The present invention generally relates to carbon dioxide (CO.sub.2) sensors. In one embodiment, the present invention relates to a carbon dioxide (CO.sub.2) sensor that incorporates lithium phosphate (Li.sub.3PO.sub.4) as an electrolyte and sensing electrode comprising a combination of lithium carbonate (Li.sub.2CO.sub.3) and barium carbonate (BaCO.sub.3). In another embodiment, the present invention relates to a carbon dioxide (CO.sub.2) sensor has a reduced sensitivity to humidity due to a sensing electrode with a layered structure of lithium carbonate and barium carbonate. In still another embodiment, the present invention relates to a method of producing carbon dioxide (CO.sub.2) sensors having lithium phosphate (Li.sub.3PO.sub.4) as an electrolyte and sensing electrode comprising a combination of lithium carbonate (Li.sub.2CO.sub.3) and barium carbonate (BaCO.sub.3).

  19. Detection of zinc oxide and cerium dioxide nanoparticles during drinking water treatment by rapid single particle ICP-MS methods.

    Science.gov (United States)

    Donovan, Ariel R; Adams, Craig D; Ma, Yinfa; Stephan, Chady; Eichholz, Todd; Shi, Honglan

    2016-07-01

    Nanoparticles (NPs) entering water systems are an emerging concern as NPs are more frequently manufactured and used. Single particle inductively coupled plasma-mass spectrometry (SP-ICP-MS) methods were validated to detect Zn- and Ce-containing NPs in surface and drinking water using a short dwell time of 0.1 ms or lower, ensuring precision in single particle detection while eliminating the need for sample preparation. Using this technique, information regarding NP size, size distribution, particle concentration, and dissolved ion concentrations was obtained simultaneously. The fates of Zn- and Ce-NPs, including those found in river water and added engineered NPs, were evaluated by simulating a typical drinking water treatment process. Lime softening, alum coagulation, powdered activated carbon sorption, and disinfection by free chlorine were simulated sequentially using river water. Lime softening removed 38-53 % of Zn-containing and ZnO NPs and >99 % of Ce-containing and CeO2 NPs. Zn-containing and ZnO NP removal increased to 61-74 % and 77-79 % after alum coagulation and disinfection, respectively. Source and drinking water samples were collected from three large drinking water treatment facilities and analyzed for Zn- and Ce-containing NPs. Each facility had these types of NPs present. In all cases, particle concentrations were reduced by a minimum of 60 % and most were reduced by >95 % from source water to finished drinking water. This study concludes that uncoated ZnO and CeO2 NPs may be effectively removed by conventional drinking water treatments including lime softening and alum coagulation.

  20. The carbon monoxide oxidation reaction over controlled catalyst structures based on gold/cerium dioxide thin films

    Science.gov (United States)

    Zhou, Zheng

    Gold-based catalysts have attracted significant research interest due to their remarkably high activity for many important reactions, including the low-temperature CO oxidation reaction. Despite extensive studies, several fundamental issues in the understanding of CO oxidation over supported gold catalysts are unresolved. The locus and nature of active sites, including the role of the metal, metal oxide support, and their interface, remain controversial. The objectives of this thesis were to study CO oxidation on Au/CeO2 catalysts that were prepared using thin film techniques so as to form geometrically controlled structures in contrast to the typical supported nanoparticle systems. Using these structures enables one to evaluate the contribution of metal oxide support (CeO2), and locate and identify the active sites in the Au/CeO2 system. In particular, the specific contribution to the reaction by the metal/oxide interface, the role and nature of the vacancies in the oxide, the role of the dimensions of the Au and ceria, and the role of stress in the gold films have been investigated. Two catalyst systems, each employing nanoscale films, were investigated. One was formed from a "single layer" of metal or oxide in the form of an extended surface that was then decorated with a thin layer of the other catalyst partner; the second approach was a study of multilayer metal/oxide structures to assess the role of the metal/metal oxide interface. More specifically the reaction sites formed at the three-phase boundary of metal, metal oxide and gas. In the first case, a Au film (4.5nm) was prepared using vapor deposition on SiO2/Si (100) substrates. The gold coalesced into discrete islands with large lateral size (20-100nm) and was found to be only weakly active. The extremely low activity of gold with large lateral extended surface has been attributed to the lack of uncoordinated gold atoms on this type of gold surface. Subsequently decorating the gold with nanosized ceria created an active catalyst with an activity about three orders of magnitude higher. In addition, the activity scaled with the extent of the ceria decoration on the same type of gold surface. Comparison of the activities between this large-sized gold catalyst and the conventional nanosized gold catalysts reported in the literature showed that the two types of catalysts were not greatly different in activity. This result demonstrates that there is a reaction channel that is promoted by ceria, and is independent of the size of the gold. Nanoscale gold is not a necessary requirement for activity. Comparing Au films as-deposited and after annealing, with the same amount of ceria decoration, the as-deposited gold film was slightly more active than the annealed gold film, which indicates the roughness or stress in the gold plays a minor role in the activity. Properties such as the number of defects in ceria and the morphology/strain in gold were controlled for the films before decorating the surface with nanoparticles of the counter material. It was found that defects in ceria affected the activity. A sample with 24% Ce3+ was more than twenty times more active than one containing 7% Ce3+ with the same amount of Au decoration. The decreased activity of Nb-doped ceria provided evidence that the active defects in ceria are its oxygen vacancies. Stability studies showed that the morphology change and the stress reduction in gold, the defect loss in ceria, and the surface contamination all contributed to activity loss with time-on-stream. However, key among these parameters is the ceria oxygen defect loss. The structure change such as the reduction in atomic level roughness and the defect loss in ceria were irreversible to treatments in He (up to 250°C) and H2 (up to 200°C) and accounted for over 90% activity loss of the catalysts in the model structure. Some of the surface contaminants can be removed by purging with inert gas at elevated temperature, however, the recovered activity was only a fraction of the initial activity. The deactivation rate was higher in the first few hours on stream, which was attributed to the structural change, especially loss of interaction at the interface between the gold and ceria, and the activity loss was over 50%. The long-term deactivation is attributed to further sintering of the gold. The deactivation continued even when only less than 1% of the initial activity remained. Kinetic studies were performed on a relatively stable sample. After correcting for deactivation, the reaction order was found to be 0.62 for CO and 0.26 for O2. The results fell in the range of the values reported by other researchers. These results indicated that both CO and O2 were adsorbed on the surface during the reaction. Additional spectroscopic studies are recommended to identify the type of adsorbed oxygen. The second structure examined used multilayer Au/CeO2 structures in the form of nanotowers with 10 micron cross-sectional areas but with alternating nano-layers of each phase. Each nanotower has an inert SiO2 layer on the top so only the edge of the multilayer was exposed to the gaseous reactants. By inserting inert layers between Au and ceria layers, the length of the exposed interface or the three-phase boundary of the gold/ceria can be changed independently of the total exposed surface area of gold and ceria and independently of the film thickness of each layer. Some nanotowers were prepared with gold film thicknesses corresponding to the typical dimension of gold in supported active nanosized catalysts. The nanotowers were characterized using AFM, SEM, and TEM. It was found that the three-phase boundary between any two layers is essentially a straight line and the activity scaled with the length of the three-phase boundary for nanotowers with the same structure (film thickness and surface treatment). Variable activity per unit length was observed, but this was a secondary, minor effect. The variability is a complex function of strain relaxation of gold with increased film thickness, annealing, and surface treatment with Ar+ sputtering, all of which might have affected the properties of the interface. The overall finding of this thesis is that the strong interfacial interaction between a highly defective ceria and gold (of any size) creates the active gold sites for the CO oxidation reaction. Key words: CO oxidation, gold, ceria, interface, nanoparticles, thin films

  1. Convenient synthesis of substituted pyrroles via a cerium (IV ammonium nitrate (CAN-catalyzed Paal–Knorr reaction

    Directory of Open Access Journals (Sweden)

    Ahmed Kamal

    2016-07-01

    Full Text Available A screening of various cerium salts for promoting the Paal–Knorr pyrrole synthesis revealed the superiority of cerium (IV ammonium nitrate (CAN as a catalyst. Excellent yields of substituted pyrroles were obtained in CAN-catalyzed Paal–Knorr reactions of 1,4-diketones with various amines. The protocol is noteworthy for the mild reaction condition, short reaction times, scalability and easy isolation of products and high yields of the products.

  2. Study of gels of molybdenum with cerium in the preparation of generators of 99Mo - 99mTc

    OpenAIRE

    Vanessa Moraes; Bárbara Marczewski; Carla Roberta Dias; João Alberto Osso Junior

    2005-01-01

    99mTc has ideal nuclear properties for organ imaging in nuclear medicine, and it is obtained from the 99Mo-99mTc generator. Four different types of generators are available: chromatographic that uses 99Mo from fission of uranium; MEK solvent extraction; Tc2O7 sublimation; gel chromatographic. This work presents the preparation of gel generators of molybdenum with cerium and characterization of the gels: mass ratio between molybdenum and cerium, structure, size of particles and elution percent...

  3. Bringing Planctomycetes into pure culture

    Directory of Open Access Journals (Sweden)

    Olga Maria Lage

    2012-12-01

    Full Text Available Planctomycetes have been known since the description of Planctomyces bekefii by Gimesi at the beginning of the twentieth century (1924, although the first axenic cultures were only obtained in the 1970s. Since then, eleven genera with fourteen species have been validly named and five candidatus genera belonging to the anaerobic ammonium oxidation, anammox bacteria have also been discovered. However, Planctomycetes diversity is much broader than these numbers indicate, as shown by environmental molecular studies. In recent years the authors have attempted to isolate and cultivate additional strains of Planctomycetes. This paper provides a summary of the isolation work that was carried out to obtain in pure culture Planctomycetes from several environmental sources. The following strains and planctomycetes have been successfully isolated: two freshwater strains from the sediments of an aquarium, which were described as a new genus and species, Aquisphaera giovannonii; several Rhodopirellula strains from the sediments of a water treatment recycling tank of a marine fish farm; and more than 140 planctomycetes from the biofilm community of macroalgae. This collection comprises several novel taxa that are being characterized and described. Improvements in the isolation methodology were made in order to optimize and enlarge the number of Planctomycetes isolated from the macroalgae. The existence of an intimate and an important relationship between planctomycetes and macroalgae reported before by molecular studies is therefore supported by culture dependent methods.

  4. Isomerically Pure Tetramethylrhodamine Voltage Reporters.

    Science.gov (United States)

    Deal, Parker E; Kulkarni, Rishikesh U; Al-Abdullatif, Sarah H; Miller, Evan W

    2016-07-27

    We present the design, synthesis, and application of a new family of fluorescent voltage indicators based on isomerically pure tetramethylrhodamines. These new Rhodamine Voltage Reporters, or RhoVRs, use photoinduced electron transfer (PeT) as a trigger for voltage sensing, display excitation and emission profiles in the green to orange region of the visible spectrum, demonstrate high sensitivity to membrane potential changes (up to 47% ΔF/F per 100 mV), and employ a tertiary amide derived from sarcosine, which aids in membrane localization and simultaneously simplifies the synthetic route to the voltage sensors. The most sensitive of the RhoVR dyes, RhoVR 1, features a methoxy-substituted diethylaniline donor and phenylenevinylene molecular wire at the 5'-position of the rhodamine aryl ring, exhibits the highest voltage sensitivity to date for red-shifted PeT-based voltage sensors, and is compatible with simultaneous imaging alongside green fluorescent protein-based indicators. The discoveries that sarcosine-based tertiary amides in the context of molecular-wire voltage indicators prevent dye internalization and 5'-substituted voltage indicators exhibit improved voltage sensitivity should be broadly applicable to other types of PeT-based voltage-sensitive fluorophores.

  5. Structure Analysis of Oxidation Film of Ignition-Inhibition AZ91D Ma gnesium Alloy Added with Cerium

    Institute of Scientific and Technical Information of China (English)

    黄晓锋; 周宏; 何镇明

    2003-01-01

    The effect of cerium on ignition temperature of AZ91D magnesium alloy was studied. By the addition of cerium of 1%, the ignition temperature is raised by 180 ℃, so the magnesium alloy added with cerium can be melted in air. The burning temperature increases with the increasing of cerium. The structure and chemical compositions of the surface oxide film were investigated by XRD and Auger electron spectrometry(AES). The results of XRD indicate that the oxide film of the surface of ignition-inhibition magnesium alloy can change from loose structure of simple magnesia to compact composite structure consisting of magnesia, cerium oxide, Mg17 A112 and aluminum oxide, which has excellent ignition-inhibition effect. AES depth profile analysis shows that the oxide film can be divided into three layers. The outside layer is mainly made up of magnesia, the middle layer, which consists of cerium oxide, magnesia, and aluminum oxide, is compound and compact. Thermodynamic analysis indicates that the structure of the surface oxide film is accordant to the change of free energy and high vapor pressure of magnesium.

  6. Chromatographic separation of cerium(Ⅲ) in L-valine medium using poly[dibenzo-18-crown-6

    Institute of Scientific and Technical Information of China (English)

    SABALE Sandip R; MOHITE Baburao S

    2009-01-01

    A column chromatographic method has been developed for the separation and determination of cerium(Ⅲ) using poly[dibenzo-18-crown-6]. The separation was carried out in L-valine medium. The adsorption of cerium(Ⅲ) was quantitative from 1×10-1 to 1×10-4 mol/L L-valine. Amongst the various eluents, 1.0-8.0 mol/L hydrochloric acid, 1.0-8.0 mol/L hydrobromic acid, 1.0-8.0 mol/L perchloric acid, 1.0-2.0 mol/L sulfuric acid and 4.0-5.0 mol/L acetic acid, were found to be the efficient eluents for cerium(Ⅲ). The capacity of poly[dibenzo-18-crown-6] for cerium(Ⅲ) was (0.428±0.01) mmol/g. The method was applied to the separation of cerium(Ⅲ) from associated elements link uranium(Ⅵ) and thorium(Ⅳ). It was also applied for the determination of cerium(Ⅲ) in geological samples. The method is simple, rapid and selective with good reproducibility (approximately±2% ).

  7. Light microscopical localization of enzymes by means of cerium-based methods. I.V. Optimization procedures for acid phosphatase.

    Science.gov (United States)

    Halbhuber, K J; Zimmermann, N; Feuerstein, H

    1986-01-01

    The earlier described cerium based histochemical reaction for acid phosphatase [Ce-Pb-reaction, Zimmermann and Halbhuber (1985)] was optimized. The target tissues (kidney, intestine) were fixed by perfusion with glutaraldehyde in cacodylate or piperazine buffer in anesthetized animals. Postfixation of prefixed sections is not advantageous because of the detectable repressing of the enzyme activity. Moreover, the employment of unfixed cryostat sections, which were postfixed, was always connected with a complete abolition of the acid phosphatase activity. The optimal concentration of the primary capture cerium III chloride in the incubation medium is about 1 mmol. Lower concentrations lead to an incomplete histochemical detection of phosphatase activity in lysosomes. The treatment of cryostat sections of perfusion fixed tissue with borohydride (diminution of aldehyde induced cross links) or with dimethylsulfoxide (extraction of lysosomal materials or the well known vehicle property) brought about an improvement of the penetration capacity for cerium-III-cations into the target structures. After conversion of the cerium phosphate (primary specific reaction product) into cerium perhydroxide, oxalate or fluoride, the Ce-Pb-reaction was negative. Therefore, these blocking reactions represent specific inhibition controls, which indicates the formation and presence of cerium phosphate. On the basis of these reactions it is possible to check the specificity of the histochemical Ce-Pb-reaction for phosphatase activity in sections.

  8. Pure variation and organic stratification.

    Science.gov (United States)

    Rosanvallon, Jérôme

    2012-09-01

    The fundamental problem posed by Darwin distinguishes his theory from any transformism of the past as well as any evolutionism to come: since variation is inherent to the living, it is a question of explaining, not at all why the living varies, but instead why the living does not vary in all directions to the point of constituting a continuum of forms varying ad infinitum. What limits and stabilizes this intrinsically unlimited variation, allowing certain forms to subsist and multiply to the detriment of others, is natural selection. This double principle of intrinsic variation/extrinsic selection constitutes a vector for the unification of reality that underlies Jean-Jacques Kupiec's ontophylogenesis as well as Deleuze and Guattari's global philosophy of Nature. Therefore, everything would potentially tend to incessantly vary. The work of Kupiec and others identifies an intrinsic random variation within ontogenesis itself. For Deleuze and Guattari, it is nothing but the figure, already selected by the organic stratum, of a more fundamental or pure variation. But, in fact, nothing really varies incessantly: everything undergoes a selective pressure according to which nothing subsists as such except what manages to endure through invariance (physical stratum) or reproduction (organic stratum). Thus, organic stratification only retains from variation what ensures and augments this reproduction. In this sense, every organism stratifies, i.e. submits to its imperative of subsistence and reproduction, a body without organs that varies in itself and always tends to escape the organism, for better (intensifications of life) or worse (cancerous pathologies). Copyright © 2012 Elsevier Ltd. All rights reserved.

  9. Effects of Cerium Nitrate on Expression of CaM Ⅰ and PMCA Ca2+-ATPase mRNA in Rat Liver

    Institute of Scientific and Technical Information of China (English)

    杨维东; 王艇; 刘洁生; 雷衡毅; 杨燕生

    2001-01-01

    The effect of cerium nitrate on expression of CaM Ⅰ and PMCA1b in rat liver was studied by means of reverse transcription-polymerase chain reaction (RT-PCR). The result shows that neither a high dose (50 mg*kg-1) nor a low dose (1 mg*kg-1) of cerium nitrate induces any alterations of expression of CaM Ⅰ and PMCA 1b mRNA after recurrent intraperitoneal injection of cerium nitrate, which suggests that effect of cerium nitrate on CaM and Ca2+-ATPase might be at posttranscription level.

  10. Dissolved cerium contributes to uptake of Ce in the presence of differently sized CeO2-nanoparticles by three crop plants.

    Science.gov (United States)

    Schwabe, Franziska; Tanner, Simon; Schulin, Rainer; Rotzetter, Aline; Stark, Wendelin; von Quadt, Albrecht; Nowack, Bernd

    2015-03-01

    We investigated the uptake of cerium (Ce) dioxide nanoparticles (NPs) by hydroponically grown wheat, pumpkin and sunflower plants. The presence of plant roots in nutrient solution led to a substantial increase in the dissolution of CeO2-NP compared to plant-free medium. Experiments with Zr/CeOx-NP revealed that Ce was not only taken up in the form of NPs, but simultaneously to a significant degree also as dissolved Ce(iii) ions, which then re-precipitated in the form of CeO2-NPs inside the leaves. The contribution of dissolved Ce uptake was particularly large for particles smaller than 10 nm due to their higher dissolution rate. Our data also indicate that the translocation of Ce resulting from NP-root-exposure is species dependent. When Ce was supplied as dissolved ions, sunflower had the highest capacity of Ce-ion accumulation inside the leaves, while there was no significant difference between pumpkin and wheat. We found no Ce translocation from roots into shoots when only NPs bigger than 20 nm were applied. This study highlights that plant root activity can have a significant impact on the dissolution of CeO2-NPs in soil solution and that uptake of dissolved Ce(iii) followed by re-precipitation needs to be considered as an important pathway in studies of CeO2-NP uptake by plants.

  11. Tame Kernels of Pure Cubic Fields

    Institute of Scientific and Technical Information of China (English)

    Xiao Yun CHENG

    2012-01-01

    In this paper,we study the p-rank of the tame kernels of pure cubic fields.In particular,we prove that for a fixed positive integer m,there exist infinitely many pure cubic fields whose 3-rank of the tame kernel equal to m.As an application,we determine the 3-rank of their tame kernels for some special pure cubic fields.

  12. Dissipation-induced pure Gaussian state

    CERN Document Server

    Koga, Kei

    2011-01-01

    This paper provides some necessary and sufficient conditions for a general Markovian Gaussian master equation to have a unique pure steady state. The conditions are described by simple matrix equations, thus they can be easily applied to the so-called environment engineering for pure Gaussian state preparation. In particular, it is shown that for any given pure Gaussian state we can actually construct a dissipative process yielding that state as the unique steady state.

  13. SEQUESTERING CARBON DIOXIDE IN COALBEDS

    Energy Technology Data Exchange (ETDEWEB)

    K.A.M. Gasem; R.L. Robinson, Jr.; L.R. Radovic

    2003-03-10

    The authors' long-term goal is to develop accurate prediction methods for describing the adsorption behavior of gas mixtures on solid adsorbents over complete ranges of temperature, pressure and adsorbent types. The originally-stated, major objectives of the current project are to (1) measure the adsorption behavior of pure CO{sub 2}, methane, nitrogen, and their binary and ternary mixtures on several selected coals having different properties at temperatures and pressures applicable to the particular coals being studied, (2) generalize the adsorption results in terms of appropriate properties of the coals to facilitate estimation of adsorption behavior for coals other than those studied experimentally, (3) delineate the sensitivity of the competitive adsorption of CO{sub 2}, methane and nitrogen to the specific characteristics of the coal on which they are adsorbed; establish the major differences (if any) in the nature of this competitive adsorption on different coals, and (4) test and/or develop theoretically-based mathematical models to represent accurately the adsorption behavior of mixtures of the type for which measurements are made. As this project has developed, an important additional objective has been added to the above original list. Namely, we have been encouraged to interact with industry and/or governmental agencies to utilize our expertise to advance the state of the art in coalbed adsorption science and technology. As a result of this additional objective, we have participated with the Department of Energy and industry in the measurement and analysis of adsorption behavior as part of two distinct investigations. These include (a) Advanced Resources International (ARI) DOE Project DE-FC26-00NT40924, ''Adsorption of Pure Methane, Nitrogen, and Carbon Dioxide and Their Mixtures on Wet Tiffany Coal'', and (b) the DOE-NETL Project, ''Round Robin: CO{sub 2} Adsorption on Selected Coals''. These activities

  14. SEQUESTERING CARBON DIOXIDE IN COALBEDS

    Energy Technology Data Exchange (ETDEWEB)

    K.A.M. Gasem; R.L. Robinson, Jr.; J.E. Fitzgerald; Z. Pan; M. Sudibandriyo

    2003-04-30

    The authors' long-term goal is to develop accurate prediction methods for describing the adsorption behavior of gas mixtures on solid adsorbents over complete ranges of temperature, pressure, and adsorbent types. The originally-stated, major objectives of the current project are to: (1) measure the adsorption behavior of pure CO{sub 2}, methane, nitrogen, and their binary and ternary mixtures on several selected coals having different properties at temperatures and pressures applicable to the particular coals being studied, (2) generalize the adsorption results in terms of appropriate properties of the coals to facilitate estimation of adsorption behavior for coals other than those studied experimentally, (3) delineate the sensitivity of the competitive adsorption of CO{sub 2}, methane, and nitrogen to the specific characteristics of the coal on which they are adsorbed; establish the major differences (if any) in the nature of this competitive adsorption on different coals, and (4) test and/or develop theoretically-based mathematical models to represent accurately the adsorption behavior of mixtures of the type for which measurements are made. As this project developed, an important additional objective was added to the above original list. Namely, we were encouraged to interact with industry and/or governmental agencies to utilize our expertise to advance the state of the art in coalbed adsorption science and technology. As a result of this additional objective, we participated with the Department of Energy and industry in the measurement and analysis of adsorption behavior as part of two distinct investigations. These include (a) Advanced Resources International (ARI) DOE Project DE-FC26-00NT40924, ''Adsorption of Pure Methane, Nitrogen, and Carbon Dioxide and Their Mixtures on Wet Tiffany Coal'', and (b) the DOE-NETL Project, ''Round Robin: CO{sub 2} Adsorption on Selected Coals''. These activities, contributing

  15. Synthesis of mesoporous cerium-zirconium mixed oxides by hydrothermal templating method

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Mesoporous cerium-zirconium mixed oxides were prepared by hydrothermal method using cetyl trimethyl ammonium bromide (CTAB) as template.The effects of amount of template,pH value of solution and hydrothermal temperature on mesostructure of samples were systematically investigated.The final products were characterized by XRD,TEM,FT-IR,and BET.The results indicate that all the cerium-zirconium mixed oxides present a meso-structure.At molar ratio of n(CTAB)/n((Ce)+(Zr))=0.15,pH value of 9,and hydrothermal temperature of 120 ℃,the samples obtained possess a specific surface area of 207.9 m2/g with pore diameter of 3.70 nm and pore volume of 0.19 cm3/g.

  16. Structure and synergetic antibacterial effect of zinc and cerium carried sodium zirconium phosphates

    Institute of Scientific and Technical Information of China (English)

    YANG Yunhua; DAI Guangjian; TAN Shaozao; LIU Yingliang; SHI Qingshan; OUYANG Yousheng

    2011-01-01

    Zinc and cerium carried zirconium phosphates (Zn-Ce/ZrPs) were prepared by exchanging zinc and cerium cations into sodium zirconium phosphate (NaZrP) through the ion-exchange method and characterized by X-ray diffraction(XRD), energy dispersive X-ray spectroscopy (EDX) and scanning electron microscopy (SEM). Furthermore, the specific surface area, zeta potential and antibacterial activity were tested. The results showed that Zn-Ce/ZrPs were with hexagonal crystal system, and the surface area of Zn-Ce/ZrPs increased much more than that of NaZrP. Zn-Ce/ZrPs showed obvious synergetic antibacterial effect, and have the potential to be used as antibacterial agents in environmental control.

  17. Color-Fading Spectrophotometric Determination of Cerium with DBC-Arsenazo

    Institute of Scientific and Technical Information of China (English)

    翟庆洲; 张晓霞

    2004-01-01

    In the medium of 0.18~1.08 mol·L-1 sulfuric acid, cerium(Ⅳ) has the color-fading effect on DBC-arsenazo. The apparent molar absorptivity of the color-fading reaction is ε530 nm=1.03×104 L·mol-1·cm-1. Beer′s law is obeyed over the range of 1.20~12.0 μg·ml-1 of Ce (Ⅳ) which shows a linear relationship with the decrease in the absorbance of the colored solution. The effect of thirty-six coexisting ions was studied. The method was applied to the determination of the trace amount of cerium in water samples and has the advantage of high accuracy and good selectivity.

  18. Synthesis, characterization and antimicrobial activity of zinc and cerium co-doped α-zirconium phosphate

    Institute of Scientific and Technical Information of China (English)

    DAI Guangjian; YU Aili; CAI Xiang; SHI Qingshan; OUYANG Yousheng; TAN Shaozao

    2012-01-01

    A series of zinc ions or/and cerium ions co-doped a-zirconium phosphate (Zn-Ce@ZrPs) were prepared.The novel Zn-Ce@ZrPs were characterized and the antibacterial activity on Gram-negative Escherichia coli and Gram-positive Staphylococcus aureus were tested.The results showed that zinc ions (Zn2+) or/and cerium ions (Ce3+) were combined with ZrP,and the Ce3+ was adsorbed on the surface of ZrP through hydrogen bonds,while Zn2+ intercalated into the interlayer of ZrP.Zn-Ce@ZrPs showed excellent synergistic antibacterial activity.When Zn2+/Ce3+ atomic ratio was 0.6,the Zn-Ce@ZrP3 showed the highest synergistic antibacterial efficiency,suggesting great potential application as antibacterial agents in microbial control.

  19. Post treatment of silane and cerium salt as chromate replacers on galvanized steel

    Institute of Scientific and Technical Information of China (English)

    KONG Gang; LU Jintang; WU Haijiang

    2009-01-01

    A complex film on hot-dip galvanized steel sheet (HDG) was prepared by immersing the sheet in 0.1wt.% Ce(NO3)3 solution and 5vol.% silane solution in turn. The corrosion protection of the complex film was evaluated by potentiodynamic linear polarization(LPR), electrochemical impendence spectra (EIS) and natural salt spray (NSS) tests and compared with that of single cerium film and silane film. The results showed that, the presence of these films on the zinc coating hindered corrosion reaction by reducing the rate of both anodic and cathodic reaction in the corrosion process, and the corrosion protection of the complex film was much better than that of single cerium film or silane film and closed to that of chromate film, because the polarization resistance Rp and electrochemical impendence were increased markedly. Microstructure and chemical composition of these pretreated films were also investigated by scanning electron microscopy (SEM) and AES.

  20. Deposition of cerium contained conversion films on LC4 alloy with square wave pulse method

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wei; LI Jiuqing; WU Yinshun; ZHANG Pei; HE Jianping

    2004-01-01

    Cerium contained conversion films were deposited on LC4 aluminum alloy using square wave pulse (SWP) in a CeC13 solution with KMnO4 as the oxidant. Energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM) were adopted to study the composition and the morphology of the film. It is found that the film is composed of Al, Zn, Cu,and small amount of cerium. The polarization curves of the specimens treated with SWP technique measured in 3.5% (mass fraction) NaCl solution reveal that the film thus formed inhibits both the anodic and cathodic process of the corrosion of the specimen. The immersion tests of treated specimens in 3.5% NaCl solution indicate that the corrosion resistance of the SWP treated specimen is better than that of the untreated and is equivalent to or even better than that of the traditionally electrochemically treated specimens.

  1. Reduction behavior of cerium(Ⅲ) ions in NaCl-2CsCl melt

    Institute of Scientific and Technical Information of China (English)

    QI Xue; ZHU Hongmin

    2005-01-01

    The cathodic process of cerium(Ⅲ) ions in NaCl-2CsCl melt was studied by cyclic voltammetry and square wave voltammetry with tungsten and gold electrodes at 873 K. The two electroanalytical methods yield similar results. The cathodic process of cerium(Ⅲ) ions consists of two reversible steps: Ce3+ + e-= Ce2+ and Ce2+ + 2e-= Ce. The half wave potentials of Ce3+/Ce2+ and Ce2+/Ce were determined as -2.525 V vs. Cl2/Cl- and -2.975 V vs. Cl2/Cl-, respectively. The diffusion coefficient of Ce3+ was also determined as 5.5 × 10-5 cm2·s-1.

  2. Energy transfer and thermal studies of Pr3+ doped cerium oxalate crystals

    Indian Academy of Sciences (India)

    R Pragash; Gijo Jose; N V Unnikrishnan; C Sudarsanakumar

    2011-07-01

    Energy transfer process at room temperature for cerium (sensitizer) oxalate single crystals doped with different concentrations (10, 13, 15, 17 and 20%) of praseodymium ions (activator) grown by hydro silica gel method has been evaluated. The analysis of energy level diagrams of cerium and praseodymium ions indicates that the energy gap between the sensitizer and the activator ions varies in a small range suggesting a possible energy transfer from the Ce3+ to Pr3+. The emission and absorption spectra of these crystals were recorded. The overlapping of the absorption spectra of Pr3+ and emission spectra of Ce3+ at wavelengths 484 and 478 nm, respectively, strongly supports the possible energy transfer process in this system. From the absorption spectra, oscillator strength, electric dipole moment, branching ratio and Judd–Ofelt parameters of this system were evaluated by least square programming. The quantum efficiency, energy transfer probabilities and thermal properties have been studied.

  3. Thermodynamics of the α -γ transition in cerium studied by an LDA + Gutzwiller method

    Science.gov (United States)

    Tian, Ming-Feng; Song, Hai-Feng; Liu, Hai-Feng; Wang, Cong; Fang, Zhong; Dai, Xi

    2015-03-01

    Utilizing the local-density approximation (LDA) + Gutzwiller method, we have studied the α -γ transition in cerium. Our results indicate that the volume collapse transition between α and γ phases is present at zero temperature with negative pressure. By further providing a newly finite temperature generalization of the LDA + Gutzwiller method (using the mean-field potential approach), the entropy contributed by both electronic quasiparticles and lattice vibration included, we obtain the Gibbs free energy at a given volume and temperature, from which we get the α -γ transition at finite temperature and pressure. Our results indicate that the electronic entropy and lattice vibrational entropy both play important roles in the α -γ transition. We also calculated the equation of state and phase diagram of cerium, finding good agreement with the experiments.

  4. Monte Carlo radiative transfer simulation of a cavity solar reactor for the reduction of cerium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Villafan-Vidales, H.I.; Arancibia-Bulnes, C.A.; Dehesa-Carrasco, U. [Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico, Privada Xochicalco s/n, Col. Centro, A.P. 34, Temixco, Morelos 62580 (Mexico); Romero-Paredes, H. [Departamento de Ingenieria de Procesos e Hidraulica, Universidad Autonoma Metropolitana-Iztapalapa, Av. San Rafael Atlixco No.186, Col. Vicentina, A.P. 55-534, Mexico D.F 09340 (Mexico)

    2009-01-15

    Radiative heat transfer in a solar thermochemical reactor for the thermal reduction of cerium oxide is simulated with the Monte Carlo method. The directional characteristics and the power distribution of the concentrated solar radiation that enters the cavity is obtained by carrying out a Monte Carlo ray tracing of a paraboloidal concentrator. It is considered that the reactor contains a gas/particle suspension directly exposed to concentrated solar radiation. The suspension is treated as a non-isothermal, non-gray, absorbing, emitting, and anisotropically scattering medium. The transport coefficients of the particles are obtained from Mie-scattering theory by using the optical properties of cerium oxide. From the simulations, the aperture radius and the particle concentration were optimized to match the characteristics of the considered concentrator. (author)

  5. CARBON DIOXIDE FIXATION.

    Energy Technology Data Exchange (ETDEWEB)

    FUJITA,E.

    2000-01-12

    Solar carbon dioxide fixation offers the possibility of a renewable source of chemicals and fuels in the future. Its realization rests on future advances in the efficiency of solar energy collection and development of suitable catalysts for CO{sub 2} conversion. Recent achievements in the efficiency of solar energy conversion and in catalysis suggest that this approach holds a great deal of promise for contributing to future needs for fuels and chemicals.

  6. DEVELOPMENT OF A COMPOSITE OF POLY-Ɛ-CAPROLACTONE-CERIUM OXIDE

    OpenAIRE

    Alejandra Melissa Martínez-Hernández; Simón Yobanny Reyes-López

    2017-01-01

    Nanotechnology is used in a variety of sectors for the manufacture of materials. However, there is a risk from exposure to nanomaterials due to their chemical composition and processing form, giving rise to health risks. CeO2 particles present antioxidant properties that accelerate the wound poly-Ɛ-caprolactone (PCL) provides the property of biocompatibility and biodegradability of the material. For the regulation of the transport and release of cerium oxide particles was incorporated into a ...

  7. Photocatalytic C-C Bond Cleavage and Amination of Cycloalkanols by Cerium(III) Chloride Complex.

    Science.gov (United States)

    Guo, Jing-Jing; Hu, Anhua; Chen, Yilin; Sun, Jianfeng; Tang, Haoming; Zuo, Zhiwei

    2016-12-05

    A general strategy for the cleavage and amination of C-C bonds of cycloalkanols has been achieved through visible-light-induced photoredox catalysis utilizing a cerium(III) chloride complex. This operationally simple methodology has been successfully applied to a wide array of unstrained cyclic alcohols, and represents the first example of catalytic C-C bond cleavage and functionalization of unstrained secondary cycloalkanols.

  8. Effect of cerium addition on microstructure and texture of aluminum foil for electrolytic capacitors

    Institute of Scientific and Technical Information of China (English)

    王海燕; 李文学; 任慧平; 黄丽颖; 王向阳

    2010-01-01

    Anode foil of aluminum electrolytic capacitor,which requires large surface area for high capacitance,were prepared by rolling,annealing and electrochemical etching.Effects of cerium addition on the capacitance of aluminum electrolytic capacitors were investigated.Microstructure of the aluminum foil surface was observed by optical microscopy(OM) and scanning electron microscopy(SEM).Electron back scattered diffraction(EBSD) was also employed to reveal texture evolvement of cold-rolled aluminum foil after ann...

  9. CO Responses of Sensors Based on Cerium Oxide Thick Films Prepared from Clustered Spherical Nanoparticles

    OpenAIRE

    Woosuck Shin; Takafumi Akamatsu; Toshio Itoh; Ichiro Matsubara; Noriya Izu

    2013-01-01

    Various types of CO sensors based on cerium oxide (ceria) have been reported recently. It has also been reported that the response speed of CO sensors fabricated from porous ceria thick films comprising nanoparticles is extremely high. However, the response value of such sensors is not suitably high. In this study, we investigated methods of improving the response values of CO sensors based on ceria and prepared gas sensors from core-shell ceria polymer hybrid nanoparticles. These hybrid nano...

  10. Broadly tunable ultraviolet miniature cerium-doped LiLuF lasers.

    Science.gov (United States)

    Liu, H; Spence, D J; Coutts, D W; Sato, H; Fukuda, T

    2008-02-04

    Ultraviolet (UV) miniature cerium fluoride lasers have been demonstrated using a low cost, frequency-quadrupled microchip Nd:YAG pump laser. The use of miniature laser cavities was shown to significantly improve the laser performance in the low pump power region. We have achieved slope efficiencies up to 70% and pump thresholds as low as 100 nJ. Continuous tuning from 306 nm to 338 nm was achieved using a Brewster angle prism.

  11. Intensification of electrochemical properties of the molten chloride electrolytes of the cerium subgroup lanthanides

    Science.gov (United States)

    Shabanov, O. M.; Suleymanov, S. I.; Magomedova, A. O.

    2017-01-01

    The electrical conductivity of molten chloride electrolytes of the cerium subgroup lanthanides increases with rising electric field strength and strive to achieve the limiting high voltage values (Wien effect). On exposure of the high-voltage microsecond pulsed fields, the melts are transited into a prolonged non-equilibrium state with increased electrical conductivity and electrolyze current density. During the relaxation processes in non-equilibrium melts, increased electrical conductivity tends to restore the values that are specific to equilibrium systems.

  12. Chlorine dioxide and hemodialysis

    Energy Technology Data Exchange (ETDEWEB)

    Smith, R.P. (Dartmouth Coll., Hanover, NH (USA). Dept. of Pharmacology and Toxicology)

    1989-05-01

    Because it has little or no tendency to generate carcinogenic trihalomethanes such as chloroform, chlorine dioxide is an attractive alternative to chlorine for drinking water disinfection. There are, however, concerns about its acute toxicity, and the toxic effects of its by-products, chlorite and chlorate. The human experience with chlorine dioxide in both controlled, prospective studies and in actual use situations in community water supplies have as yet failed to reveal adverse health effects. The EPA has recommended standards of 0.06 mg/L for chlorine dioxide and standards of 0.007 mg/L for chlorite and chlorate in drinking water. Among groups who may be at special risk from oxychlorines in drinking water are patients who must undergro chronic extracorporeal hemodialysis. Although even units for home hemodialysis are supposed to be equipped with devices which effectively remove oxychlorines, there is a always a possibility of operator error or equipment failure. When the equipment is adequately maintained, it is likely that dialysis patients will have more intensive exposures from drinking water than from dialysis fluids despite the much larger volumes of water that are involved in dialysis. This paper discusses a hemodialysis and the standards and effects of oxychlorines. 90 refs., 2 tabs.

  13. Effects of cerium salts on corrosion behaviors of Si–Zr hybrid sol–gel coatings

    Directory of Open Access Journals (Sweden)

    Yu Mei

    2015-04-01

    Full Text Available The present work examines the effects of cerium salts on corrosion behaviors of Si–Zr hybrid sol–gel coatings. The Si–Zr hybrid sol–gel coatings on a 2A12 aluminum substrate were prepared through hydrolysis and condensation of glycidoxypropyl-trimethoxy-silane (GTMS and zirconium(IV n-propoxide (TPOZ. Used as inhibitors for corrosion, three types of cerium salts (Ce(NO33, CeCl3, and Ce(CH3COO3 were doped into the sol–gel coatings. Fourier transform infrared (FTIR and scanning electron microscopy (SEM were employed to investigate the structures and morphologies of various coatings, and the corrosion resistances of the coatings were evaluated by electrochemical methods and neutral salt spray tests. Experimental results indicate that the addition of cerium salts can hinder the process of corrosion due to their self-healing abilities. Furthermore, the sol–gel coating doped with Ce(CH3COO3 has the best corrosion resistance because of the promotions of hydrolysis and condensation provided by CH3COO−.

  14. Infrared, thermal and X-ray diffraction analysis of cerium soaps

    Energy Technology Data Exchange (ETDEWEB)

    Mehrotra, K.N. [Agra Univ. (India). Dept. of Chemistry; Chauhan, M. [Agra Univ. (India). Dept. of Chemistry; Shukla, R.K. [R.B.S. Coll., Agra (India)

    1997-03-01

    The physico-chemical characteristics of cerium soaps (Caproate and caprate) in solid state were investigated by IR, thermal and X-ray diffraction measurements. The IR results reveal that the fatty acids exist in dimeric state through hydrogen bonding and soaps possess partial ionic character. The decomposition reaction was found kinetically of zero order with energy of activation 6.7 and 7.3 K cal mol{sup -1} for cerium caproate and caprate, respectively. The X-ray diffraction measurements were used to calculate the long spacings and the results confirm the double layer structure of cerium soaps. (orig.) [Deutsch] Mit Hilfe von IR-, thermischen und Roentgendiffraktionsmessungen wurden die physikalisch-chemischen Eigenschaften von Cerseifen (Capron- und Caprylsaeuresalze)in festem Zustand bestimmt. Die IR-Untersuchungen zeigen, dass die Fettseifen in dimerem Zustand, gebunden durch Wasserstoffbruecken vorliegen und partiell ionischen Charakter haben. Die Zersetzungsreaktion war von einer Kinetik nullter Ordnung, die Aktivierungsenergien lagen bei 6,7 K cal mol{sup -1} fuer Capronsaeuresalze und 7,3 K cal mol{sup -1} fuer Caprylsaeuresalze. Mit Hilfe von Roentgendiffraktionsmessungen wurden die grossen Zwischenraeume bestimmt. Die Ergebnisse lassen auf eine Doppelschichtstruktur der Cerseifen schliessen. (orig.)

  15. Nanoceria and bulk cerium oxide effects on the germination of asplenium adiantum-nigrum spores

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Garay, A.; Pintos, B.; Manzanera, J.A.; Prada, C.; Martin, L.; Gabriel y Galan, J.M.

    2016-07-01

    Aim of the study: The effect of cerium oxide engineered nanoparticles on the spore germination of the fern. Asplenium adiantum-nigrum. Area of study: France, Britanny Region, Finistére Department, Plougonvelin, in rocks near the sea. Material and methods: Asplenium spores were cultured in vitro on agar medium with Nano-CeO2 (less than 25 nm particle size) and bulk-CeO2. The addition of each nano- and bulk particles ranged from 0 to 3000 mg L-1. Observations on rhizoidal and prothallial cells during first stages of gametophyte development were made. The No-Observed-Adverse-Effect concentration (NOAEC) and Lowest-Observed-Adverse-Effect-Concentration (LOEC) values for spore germination rate data were analyzed. Main results: Germination was speeded up by 100 to 2000 mg L-1 nanoceria, while bulk cerium oxide had the same effect for 500 to 200 mg L-1 concentrations. Present results showed cellular damage in the protonema while rhizoid cells seemed not to be affected, as growth and membrane integrity remained. Research highlights: Both nanosized and bulk cerium oxide are toxic for the fern Asplenium adiantum-nigrum, although diverse toxicity patterns were shown for both materials. Diverse toxic effects have been observed: chloroplast membrane damage and lysis, cell wall and membrane disruption which leads to cell lysis; and alterations in morphology and development. (Author)

  16. Cerium, gallium and zinc containing mesoporous bioactive glass coating deposited on titanium alloy

    Science.gov (United States)

    Shruti, S.; Andreatta, F.; Furlani, E.; Marin, E.; Maschio, S.; Fedrizzi, L.

    2016-08-01

    Surface modification is one of the methods for improving the performance of medical implants in biological environment. In this study, cerium, gallium and zinc substituted 80%SiO2-15%CaO-5%P2O5 mesoporous bioactive glass (MBG) in combination with polycaprolactone (PCL) were coated over Ti6Al4 V substrates by dip-coating method in order to obtain an inorganic-organic hybrid coating (MBG-PCL). Structural characterization was performed using XRD, nitrogen adsorption, SEM-EDXS, FTIR. The MBG-PCL coating uniformly covered the substrate with the thickness found to be more than 1 μm. Glass and polymer phases were detected in the coating along with the presence of biologically potent elements cerium, gallium and zinc. In addition, in vitro bioactivity was investigated by soaking the coated samples in simulated body fluid (SBF) for up to 30 days at 37 °C. The apatite-like layer was monitored by FTIR, SEM-EDXS and ICP measurements and it formed in all the samples within 15 days except zinc samples. In this way, an attempt was made to develop a new biomaterial with improved in vitro bioactive response due to bioactive glass coating and good mechanical strength of Ti6Al4 V alloy along with inherent biological properties of cerium, gallium and zinc.

  17. Preparation and Characterization of Cerium (III Doped Captopril Nanoparticles and Study of their Photoluminescence Properties

    Directory of Open Access Journals (Sweden)

    Ghamami Shahriar

    2016-01-01

    Full Text Available In this research Ce3+ doped Captopril nanoparticles (Ce3+ doped CAP-NP were prepared by a cold welding process and have been studied. Captopril may be applied in the treatment of hypertension and some types of congestive heart failure and for preventing kidney failure due to high blood pressure and diabetes. CAP-NP was synthesized by a cold welding process. The cerium nitrate was added at a ratio of 10% and the optical properties have been studied by photoluminescence (PL. The synthesized compounds were characterized by Fourier transform infrared spectroscopy. The size of CAP-NP was calculated by X-ray diffraction (XRD. The size of CAP-NP was in the range of 50 nm. Morphology of surface of synthesized nanoparticles was studied by scanning electron microscopy (SEM. Finally the luminescence properties of undoped and doped CAP-NP were compared. PL spectra from undoped CAP-NP show a strong pack in the range of 546 nm after doped cerium ion into the captopril appeared two bands at 680 and 357 nm, which is ascribed to the well-known 5d–4f emission band of the cerium.

  18. Nanoceria and bulk cerium oxide effects on the germination of asplenium adiantum-nigrum spores

    Directory of Open Access Journals (Sweden)

    Aranzazu Gomez-Garay

    2016-12-01

    Full Text Available Aim of study: The effect of cerium oxide engineered nanoparticles on the spore germination of the fern. Asplenium adiantum-nigrum. Area of study: France, Britanny Region, Finistére Department, Plougonvelin, in rocks near the sea. Material and methods: Asplenium spores were cultured in vitro on agar medium with Nano-CeO2 (less than 25 nm particle size and bulk-CeO2. The addition of each nano- and bulk particles ranged from 0 to 3000 mg L-1. Observations on rhizoidal and prothallial cells during first stages of gametophyte development were made. The No-Observed-Adverse-Effect concentration (NOAEC and Lowest-Observed-Adverse-Effect-Concentration (LOEC values for spore germination rate data were analyzed.  Main results: Germination was speeded up by 100 to 2000 mg L-1 nanoceria, while bulk cerium oxide had the same effect for 500 to 200 mg L-1 concentrations. Present results showed cellular damage in the protonema while rhizoid cells seemed not to be affected, as growth and membrane integrity remained. Research highlights: Both nanosized and bulk cerium oxide are toxic for the fern Asplenium adiantum-nigrum, although diverse toxicity patterns were shown for both materials. Diverse toxic effects have been observed: chloroplast membrane damage and lysis, cell wall and membrane disruption which leads to cell lysis; and alterations in morphology and development. Keywords: Nanoparticles; rhizoid; prothallus; chloroplast; fern.

  19. Synthesis and Characterization of Cerium Doped Titanium Catalyst for the Degradation of Nitrobenzene Using Visible Light

    Directory of Open Access Journals (Sweden)

    Padmini Ellappan

    2014-01-01

    Full Text Available Cerium doped catalyst was synthesized using Titanium isopropoxide as the Titanium source. The metal doped nanoparticles semiconductor catalyst was prepared by sol-sol method with the sol of Cerium. The synthesized catalyst samples were characterized by powder X-ray diffraction, BET surface area, thermogravimetric analysis (TGA, scanning electron microscopy (SEM, and UV-vis diffuse reflectance measurements (DRS and compared with undoped TiO2 catalyst. The photocatalytic activity of the sample was investigated for the decomposition of nitrobenzene (NB using visible light as the artificial light source. Cerium doped catalyst was found to have better degradation of nitrobenzene owing to its shift in the band gap from UV to visible region as compared to undoped TiO2 catalyst. The operational parameters were optimized with catalyst dosage of 0.1 g L−1, pH of 9, and light intensity of 500 W. The degradation mechanism followed the Langmuir Hinshelwood kinetic model with the rate constant depending nonlinearly on the operational parameters as given by the relationship Kapp (theoretical = 2.29 * 10−4 * Intensity0.584 * Concentration−0.230 * Dosage0.425 * pH0.336.

  20. Controlled Redox Chemistry at Cerium within a Tripodal Nitroxide Ligand Framework.

    Science.gov (United States)

    Bogart, Justin A; Lippincott, Connor A; Carroll, Patrick J; Booth, Corwin H; Schelter, Eric J

    2015-12-01

    Ligand reorganization has been shown to have a profound effect on the outcome of cerium redox chemistry. Through the use of a tethered, tripodal, trianionic nitroxide ligand, [((2-tBuNOH)C6 H4 CH2 )3 N](3-) (TriNOx (3-) ), controlled redox chemistry at cerium was accomplished, and typically reactive complexes of tetravalent cerium were isolated. These included rare cationic complexes [Ce(TriNOx )thf][BAr(F) 4 ], in which Ar(F) =3,5-(CF3 )2 -C6 H3 , and [Ce(TriNOx )py][OTf]. A rare complete Ce-halide series, Ce(TriNOx )X, in which X=F(-) , Cl(-) , Br(-) , I(-) , was also synthesized. The solution chemistry of these complexes was explored through detailed solution-phase electrochemistry and (1) H NMR experiments and showed a unique shift in the ratio of species with inner- and outer-sphere anions with size of the anionic X(-) group. DFT calculations on the series of calculations corroborated the experimental findings.

  1. Cytochemical localization of adenylate cyclase activity in heart tissue with cerium.

    Science.gov (United States)

    Schulze, W; Will-Shahab, L; Küttner, I

    1986-01-01

    Adenylate cyclase (AC) activity showed a doses depending inactivation of the basal activity and of the sodium fluoride stimulation by cerium in homogenates of unfixed and fixed guinea pig hearts. The isoproterenol and guanine nucleotide stimulation was not more than two times of the basal activity in glutaraldehyde-prefixed heart homogenates in the presence of 2 mmol/l CeCl3. The inactivation of the AC (activity) by cerium was less than in the presence of lead. Test tube experiments showed no differences in the precipitation of imidodiphosphate in comparison with inorganic phosphate. The substrate AMP-PNP was not spontaneously hydrolysed by 2 mmol/l CeCl3. Ultrastructural analysis of cytochemical incubation of glutaraldehyde-fixed slices and small pieces of guinea pig heart tissue showed fine-amorphous precipitations of reaction products localized along the plasma membrane of the sarcolemma, the nexuses of the intercalated discs and the T-tubule membranes. No precipitates were found neither on the junctional nor on other SR membranes. Nonspecific coarse and clumped precipitates have been detected in the intercellular space on components of the basal membranes. It was not able to demonstrate cytochemically stimulation of AC by hormones or by sodium fluoride. The localization of the basal AC activity in heart tissue seems to be better with cerium as capture agent than with lead. However, differences in the localization of the AC activity in heart tissue were not observed.

  2. Cerium Biomagnification in a Terrestrial Food Chain: Influence of Particle Size and Growth Stage.

    Science.gov (United States)

    Majumdar, Sanghamitra; Trujillo-Reyes, Jesica; Hernandez-Viezcas, Jose A; White, Jason C; Peralta-Videa, Jose R; Gardea-Torresdey, Jorge L

    2016-07-01

    Mass-flow modeling of engineered nanomaterials (ENMs) indicates that a major fraction of released particles partition into soils and sediments. This has aggravated the risk of contaminating agricultural fields, potentially threatening associated food webs. To assess possible ENM trophic transfer, cerium accumulation from cerium oxide nanoparticles (nano-CeO2) and their bulk equivalent (bulk-CeO2) was investigated in producers and consumers from a terrestrial food chain. Kidney bean plants (Phaseolus vulgaris var. red hawk) grown in soil contaminated with 1000-2000 mg/kg nano-CeO2 or 1000 mg/kg bulk-CeO2 were presented to Mexican bean beetles (Epilachna varivestis), which were then consumed by spined soldier bugs (Podisus maculiventris). Cerium accumulation in plant and insects was independent of particle size. After 36 days of exposure to 1000 mg/kg nano- and bulk-CeO2, roots accumulated 26 and 19 μg/g Ce, respectively, and translocated 1.02 and 1.3 μg/g Ce, respectively, to shoots. The beetle larvae feeding on nano-CeO2 exposed leaves accumulated low levels of Ce since ∼98% of Ce was excreted in contrast to bulk-CeO2. However, in nano-CeO2 exposed adults, Ce in tissues was higher than Ce excreted. Additionally, Ce content in tissues was biomagnified by a factor of 5.3 from the plants to adult beetles and further to bugs.

  3. Cerium(III-Selective Membrane Electrode Based on Dibenzo-24-crown-8 as a Neutral Carrier

    Directory of Open Access Journals (Sweden)

    Susheel K. Mittal

    2010-01-01

    Full Text Available Cerium(III-selective membrane electrodes have been prepared using dibenzo-24-crown-8 (DB24C8 as an electroactive material. A membrane having a composition: DB24C8 (4.5%, plasticizer (NPOE, 62.5% and PVC (33% gives the best performance. It works well over a wide Ce(III ion-concentration range of 1x10-5 M to 1x10-1 M with a Nernstian slope of 19.0 mV/decade and a detection limit of 3x10-5 M. It has a fast response time of 20 seconds and has an average lifetime of four months. The internal solution concentration does not have a significant effect on the response of the electrode except for a change in intercept of the calibration curves. The working pH range for Ce(III solutions (1x10-2 M and 1x10-3 M is 3.5-8.0. The proposed sensor shows a good selectivity for cerium(III with respect to alkali, alkaline earth, some transition and rare earth metal ions that are normally present along with cerium in its ores. The proposed sensor was investigated in partially non-aqueous media using acetone, methanol and DMSO mixtures with water. The electrode was further used as an indicator electrode for the potentiometric titration of Ce(III solution against oxalic acid solution.

  4. Effect of cerium oxide addition on electrical properties of ZnO

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, D.M. [National Research Center, Dokki, Giza (Egypt). Dept. of Ceramics; Mounir, M. [Dept. of Physics, Cairo Univ., Giza (Egypt); Mahgoub, A.S. [Cairo Univ., Giza (Egypt). Dept. of Chemistry; Turky, G. [Dept. of Physics, National Research Center, Dokki, Giza (Egypt); El-Desouky, O.A. [Cer. Cleopatra Co., Ramadan City (Egypt)

    2002-07-01

    Mixtures of ZnO and Ce{sub 6} O{sub 11} as additive were prepared by solid state reaction from the calcined oxides with the following proportions: 0.03, 0.08, 0.1, 0.2 and 0.4 mole. Disc specimens 1.2 cm 5 cm in diameter and 0.3 cm thickness were processed under a force of 70 kN and fired at 1150 C/ 30 minutes. XRD revealed the presence of limited solid solution of cerium in ZnO, as evident from the shift in the peaks [0.03-0.04 A ] up to 0.1 mole addition and remains constant. SEM revealed the presence of inter-granular phase. EDAX showed it to be a mixture of ZnO and Ce{sub 6}O{sub 11}. Also cerium was detected in the ZnO grains confirming the XRD results. RCL circuit was used to measure the capacitance and resistance at different frequencies at room temperature. The dielectric constant and conductivity were calculated. The change in resistivity with temperature was followed up to 523 K. The change in dielectric strength with temperature at spot frequency of 10 kHz is demonstrated. The electrical conductivity was found to increase with the proportion of cerium oxide up to 0.2 mole then decreased. (orig.)

  5. The Expansion Postponement in Pure Type Systems

    Institute of Scientific and Technical Information of China (English)

    宋方敏

    1997-01-01

    The expansion postponement problem in Pure Type Systems is an open problem raised by R.Pollack in 1992.In this paper,the author presents a set of necessary and sufficient conditions for this problem and a set of sufficient conditions for it.The author also gives some properties for pure typ systems without the expansion rule.

  6. Measuring the entanglement of bipartite pure states

    CERN Document Server

    Sancho, J M

    2000-01-01

    The problem of the experimental determination of the amount of entanglement of a bipartite pure state is addressed. We show that measuring a single observable does not suffice to determine the entanglement of a given unknown pure state of two particles. Possible minimal local measuring strategies are discussed and a comparison is made on the basis of their best achievable precision.

  7. Fundamentals of the pure spinor formalism

    NARCIS (Netherlands)

    Hoogeveen, J.

    2010-01-01

    This thesis presents recent developments within the pure spinor formalism, which has simplified amplitude computations in perturbative string theory, especially when spacetime fermions are involved. Firstly the worldsheet action of both the minimal and the non-minimal pure spinor formalism is derive

  8. Influence of agglomeration of cerium oxide nanoparticles and speciation of cerium(III) on short term effects to the green algae Chlamydomonas reinhardtii

    Energy Technology Data Exchange (ETDEWEB)

    Röhder, Lena A. [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Environmental Toxicology, Dübendorf 8600 (Switzerland); ETH-Zurich, Institute of Biogeochemistry and Pollutant Dynamics, Zürich 8092 (Switzerland); Brandt, Tanja [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Environmental Toxicology, Dübendorf 8600 (Switzerland); Sigg, Laura [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Environmental Toxicology, Dübendorf 8600 (Switzerland); ETH-Zurich, Institute of Biogeochemistry and Pollutant Dynamics, Zürich 8092 (Switzerland); Behra, Renata, E-mail: Renata.behra@eawag.ch [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Environmental Toxicology, Dübendorf 8600 (Switzerland)

    2014-07-01

    Highlights: • Phosphate-dispersed CeO₂ NP did not affect photosynthetic yield in C. reinhardtii. • Agglomerated CeO₂ NP slightly decreased photosynthetic yield. • Cerium(III) was shown to affect photosynthetic yield and intracellular ROS level. • Slight effects of CeO₂ NP were caused by dissolved Ce³⁺ ions present in suspensions. • Wild type and cell wall free mutant of C. reinhardtii showed the same sensitivity. - Abstract: Cerium oxide nanoparticles (CeO₂ NP) are increasingly used in industrial applications and may be released to the aquatic environment. The fate of CeO₂ NP and effects on algae are largely unknown. In this study, the short term effects of CeO₂ NP in two different agglomeration states on the green algae Chlamydomonas reinhardtii were examined. The role of dissolved cerium(III) on toxicity, its speciation and the dissolution of CeO₂ NP were considered. The role of cell wall of C. reinhardtii as a barrier and its influence on the sensitivity to CeO₂ NP and cerium(III) was evaluated by testing both, the wild type and the cell wall free mutant of C. reinhardtii. Characterization showed that CeO₂ NP had a surface charge of ~0 mV at physiological pH and agglomerated in exposure media. Phosphate stabilized CeO₂ NP at pH 7.5 over 24 h. This effect was exploited to test CeO₂ NP dispersed in phosphate with a mean size of 140 nm and agglomerated in absence of phosphate with a mean size of 2000 nm. The level of dissolved cerium(III) in CeO₂ NP suspensions was very low and between 0.1 and 27 nM in all tested media. Exposure of C. reinhardtii to Ce(NO₃)₃ decreased the photosynthetic yield in a concentration dependent manner with EC₅₀ of 7.5 ± 0.84 μM for wild type and EC₅₀ of 6.3 ± 0.53 μM for the cell wall free mutant. The intracellular level of reactive oxygen species (ROS) increased upon exposure to Ce(NO₃)₃ with effective concentrations similar to those inhibiting photosynthesis. The agglomerated Ce

  9. Reaction products of chlorine dioxide.

    OpenAIRE

    Stevens, A A

    1982-01-01

    Inspection of the available literature reveals that a detailed investigation of the aqueous organic chemistry of chlorine dioxide and systematic identification of products formed during water disinfection has not been considered. This must be done before an informed assessment can be made of the relative safety of using chlorine dioxide as a disinfectant alternative to chlorine. Although trihalomethanes are generally not formed by the action of chlorine dioxide, the products of chlorine dioxi...

  10. Reaction products of chlorine dioxide.

    OpenAIRE

    Stevens, A. A.

    1982-01-01

    Inspection of the available literature reveals that a detailed investigation of the aqueous organic chemistry of chlorine dioxide and systematic identification of products formed during water disinfection has not been considered. This must be done before an informed assessment can be made of the relative safety of using chlorine dioxide as a disinfectant alternative to chlorine. Although trihalomethanes are generally not formed by the action of chlorine dioxide, the products of chlorine dioxi...

  11. Pharmaceutical applications of supercritical carbon dioxide.

    Science.gov (United States)

    Kaiser, C S; Römpp, H; Schmidt, P C

    2001-12-01

    The appearance of a supercritical state was already observed at the beginning of the 19th century. Nevertheless, the industrial extraction of plant and other natural materials started about twenty years ago with the decaffeination of coffee. Today carbon dioxide is the most common gas for supercritical fluid extraction in food and pharmaceutical industry. Since pure supercritical carbon dioxide is a lipophilic solvent, mixtures with organic solvents, especially alcohols, are used to increase the polarity of the extraction fluid; more polar compounds can be extracted in this way. The main fields of interest are the extraction of vegetable oils from plant material in analytical and preparative scale, the preparation of essential oils for food and cosmetic industry and the isolation of substances of pharmaceutical relevance. Progress in research was made by the precise measurement of phase equilibria data by means of different methods. Apart from extraction, supercritical fluid chromatography was introduced in the field of analytics, as well as micro- and nanoparticle formation using supercritical fluids as solvent or antisolvent. This review presents pharmaceutical relevant literature of the last twenty years with special emphasis on extraction of natural materials.

  12. Grain Growth Behavior, Tensile Impact Ductility, and Weldability of Cerium-Doped Iridium Alloys

    Energy Technology Data Exchange (ETDEWEB)

    McKamey, C.G.

    2002-05-28

    An iridium alloy doped with small amounts of cerium and thorium is being developed as a potential replacement for the iridium-based DOP-26 alloy (doped with thorium only) that is currently used by the National Aeronautics and Space Administration (NASA) for cladding and post-impact containment of the radioactive fuel in radioisotope thermoelectric generator (RTG) heat sources which provide electric power for interplanetary spacecraft. This report summarizes results of studies conducted to date under the Iridium Alloy Characterization and Development subtask of the Radioisotope Power System Materials Production and Technology Program to characterize the properties of the iridium-based alloy (designated as DOP-40) containing both cerium and thorium. Included within this report are data on grain growth of sheet material in vacuum and low-pressure oxygen environments, grain growth in vacuum of the clad vent set cup material, weldability, and the effect of grain size and test temperature on tensile properties. Where applicable, data for the DOP-26 alloy are included for comparison. Both grain size and grain-boundary cohesion affect the ductility of iridium alloys. In this study it was found that cerium and thorium, when added together, refine grain size more effectively than when thorium is added by itself (especially at high temperatures). In addition, the effect of cerium additions on grain-boundary cohesion is similar to that of thorium. Mechanical testing at both low ({approx} 10{sup -3}s{sup -1}) and high ({approx} 10{sup -3}s{sup -1}) strain rates showed that the Ce/Th-doped alloys have tensile ductilities that are as good or better than the DOP-26 alloy. The general conclusion from these studies is that cerium can be used to replace some of the radioactive thorium currently used in DOP-26 while maintaining or improving its metallurgical properties. The current DOP-26 alloy meets all requirements for cladding the radioactive fuel in the RTG heat source, but the

  13. Using cerium anomaly as an indicator of redox reactions in constructed wetland

    Science.gov (United States)

    Liang, R.

    2013-12-01

    The study area, Chiayi County located in southern Taiwan, has highly developed livestock. The surface water has very low dissolved oxygen and high NH4. Under the situation, constructed wetland becomes the most effective and economic choice to treat the wastewater in the natural waterways. Hebao Island free surface constructed wetland started to operate in late 2006. It covers an area of 0.28 km2 and is subdivided into 3 major cells, which are sedimentation cell, 1st aeration cell with rooted plants and 2nd aeration cell with float plants. The water depth of cells ranges from 0.6 m to 1.2 m. The total hydraulic retention time is about a half day. In this study, the water samples were sequentially collected along the flow path. The results of hydrochemical analysis show that the untreated inflow water can be characterized with enriched NH4 (11 ppm), sulfate (6 ppm) and arsenic (50 ppb). The removal efficiency of NH4 in the first two cells is constructed wetland. However, the removal of sulfate and phosphate is very weak. It is worth to note that arsenic is still higher than the permissible limits recommended by WHO (10 ppb). The wetland operation should be tuned to take more arsenic away in the future. As demonstrated in the above, oxidation reaction is the most dominant mechanism to remove pollutants from the wastewater; therefore, dissolved oxygen is traditionally considered as an important indicator to evaluate the operation efficiency of wetland. However, it would need longer time to achieve equilibrium state of redox reaction involving dissolved oxygen due to the slower reaction rate. For example, the input water in this study has fairly high dissolved oxygen (5 ppm) but the NH4 content is still high, which indicates a non-equilibrium condition. In this study, the cerium anomaly is alternatively utilized to evaluate the water redox state. The results demonstrate that the input water has the negative cerium anomaly of -0.16. Along the flow path, the cerium

  14. Enhancing the Effectiveness of Carbon Dioxide Flooding by Managing Asphaltene Precipitation

    Energy Technology Data Exchange (ETDEWEB)

    Deo, Milind D.

    2002-02-21

    This project was undertaken to understand fundamental aspects of carbon dioxide (CO2) induced asphaltene precipitation. Oil and asphaltene samples from the Rangely field in Colorado were used for most of the project. The project consisted of pure component and high-pressure, thermodynamic experiments, thermodynamic modeling, kinetic experiments and modeling, targeted corefloods and compositional modeling.

  15. Permeability, diffusivity and solubility of carbon dioxide in fluoropolymers: An experimental and modeling study

    DEFF Research Database (Denmark)

    Neela, Vasu; von Solms, Nicolas

    2014-01-01

    . Using a high-pressure permeation cell, the permeability and diffusivity of carbon dioxide were measured in several polymers used as packing and sealing materials. These were the fluoropolymers PTFE, FKM and TFM, both pure and containing glass, graphite, Ekonol and polysulfone as additives...

  16. Nanotitanium dioxide toxicity in mouse lung is reduced in sanding dust from paint

    DEFF Research Database (Denmark)

    Saber, Anne Thoustrup; Jacobsen, Nicklas Raun; Mortensen, Alicja

    2012-01-01

    Background: Little is known of how the toxicity of nanoparticles is affected by the incorporation in complex matrices. We compared the toxic effects of the titanium dioxide nanoparticle UV-Titan L181 (NanoTiO(2)), pure or embedded in a paint matrix. We also compared the effects of the same paint...

  17. Self-poled transparent and flexible UV light-emitting cerium complex-PVDF composite: a high-performance nanogenerator.

    Science.gov (United States)

    Garain, Samiran; Sinha, Tridib Kumar; Adhikary, Prakriti; Henkel, Karsten; Sen, Shrabanee; Ram, Shanker; Sinha, Chittaranjan; Schmeißer, Dieter; Mandal, Dipankar

    2015-01-21

    Cerium(III)-N,N-dimethylformamide-bisulfate [Ce(DMF)(HSO4)3] complex is doped into poly(vinylidene fluoride) (PVDF) to induce a higher yield (99%) of the electroactive phases (β- and γ-phases) of PVDF. A remarkable enhancement of the output voltage (∼32 V) of a nanogenerator (NG) based on a nonelectrically poled cerium(III) complex containing PVDF composite film is achieved by simple repeated human finger imparting, whereas neat PVDF does not show this kind of behavior. This high electrical output resembles the generation of self-poled electroactive β-phase in PVDF due to the electrostatic interactions between the fluoride of PVDF and the surface-active positive charge cloud of the cerium complex via H-bonding and/or bipolar interaction among the opposite poles of cerium complex and PVDF, respectively. The capacitor charging capability of the flexible NG promises its applicability as piezoelectric-based energy harvester. The cerium(III) complex doped PVDF composite film exhibit an intense photoluminescence in the UV region, which might be due to a participation of electron cloud from negative pole of bipolarized PVDF. This fact may open a new area for prospective development of high-performance energy-saving flexible solid-state UV light emitters.

  18. SYNTHESIS OF CATIONIC CERIUM COMPOUNDS [CP2CE(L)2][BPH4] (L = TETRAHYDROFURAN OR TETRAHYDROTHIOPHENE) AND THE CRYSTAL-STRUCTURE OF THE TETRAHYDROTHIOPHENE DERIVATIVE

    NARCIS (Netherlands)

    HEERES, HJ; MEETSMA, A; TEUBEN, JH

    1991-01-01

    Protolysis of the cerium alkyl Cp2*CeCH(SiMe3)2 (1) by triethylammoniumtetraphenylborate provides a useful route to cationic cerium compounds [Cp2*Ce(L)2][BPh4] (2, L = tetrahydrofuran; 3, L = tetrahydrothiophene). The crystal structure of the tetrahydrothiophene derivative was determined by X-ray d

  19. Flow Boiling of Pure and Oil Contaminated Carbon Dioxide as Refrigerant

    DEFF Research Database (Denmark)

    Mohamed, A.-R. Mohamed

    2003-01-01

    described in the present report is measured heat transfer coefficient and pressure drop for flow boiling of oil free and oil contaminated CO2. Measurements have been done on tube with internal diameter of 10 mm and 4 mm- The mass flux has been varied from 90 kg/m2s to 750 kg/m2s, heat flux from 5 kW/m2...

  20. Sequestration of non-pure carbon dioxide streams in iron oxyhydroxide-containing saline repositories

    Science.gov (United States)

    Garcia, S.; Rosenbauer, Robert J.; Palandri, James L.; Maroto-Valer, M. Mercedes

    2012-01-01

    Iron oxyhydroxide, goethite (α-FeOOH), was evaluated as a potential formation mineral reactant for trapping CO2 in a mineral phase such as siderite (FeCO3), when a mixture of CO2-SO 2 flue gas is injected into a saline aquifer. Two thermodynamic simulations were conducted, equilibrating a CO2-SO2 fluid mixture with a NaCl-brine and Fe-rich rocks at 150 °C and 300 bar. The modeling studies evaluated mineral and fluid composition at equilibrium and the influence of pH buffering in the system. Results show siderite precipitates both in the buffered and unbuffered system; however, the presence of an alkaline pH buffer enhances the stability of the carbonate. Based on the model, an experiment was designed to compare with thermodynamic predictions. A CO2-SO2 gas mixture was reacted in 150 ml of NaCl-NaOH brine containing 10 g of goethite at 150 °C and 300 bar for 24 days. Mineralogical and brine chemistry confirmed siderite as the predominant reaction product in the system. Seventy-six mg of CO2 are sequestered in siderite per 10 g of goethite.

  1. Flow Boiling of Pure and Oil Contaminated Carbon Dioxide as Refrigerant

    DEFF Research Database (Denmark)

    Mohamed, A.-R. Mohamed

    2003-01-01

    of benefit of the environment. The main challenge for CO2 based refrigerant systems is to increase the performance of the heat exchangers. Especially there is a need for information concerning heat transfer and pressure drop in evaporator and condenser with CO2 as refrigerant. The reason this is the very...... high reduced pressure with CO2 compared to the reduced pressure using CFC, HCFC and HFC. CO2 has greater heat conductivity than CFC, HCFC and HFC so the influence of oil in the refrigeration system is expected to have a greater influence on the system performance. The main result of the project...... described in the present report is measured heat transfer coefficient and pressure drop for flow boiling of oil free and oil contaminated CO2. Measurements have been done on tube with internal diameter of 10 mm and 4 mm- The mass flux has been varied from 90 kg/m2s to 750 kg/m2s, heat flux from 5 kW/m2...

  2. Conformal pure radiation with parallel rays

    CERN Document Server

    Leistner, Thomas

    2011-01-01

    We define pure radiation metrics with parallel rays to be n-dimensional pseudo-Riemannian metrics that admit a parallel null line bundle K and whose Ricci tensor vanishes on vectors that are orthogonal to K. We give necessary conditions in terms of the Weyl, Cotton and Bach tensors for a pseudo-Riemannian metric to be conformal to a pure radiation metric with parallel rays. Then we derive conditions in terms of tractor calculus that are equivalent to the existence of a pure radiation metric with parallel rays in a conformal class. We also give an analogous result for n-dimensional pseudo-Riemannian pp-waves.

  3. Pure red cell aplasia and associated thymoma

    Directory of Open Access Journals (Sweden)

    Cristian Rosu

    2011-04-01

    Full Text Available Pure red cell aplasia is a rare cause of anemia, caused by an absence of red blood cell precursors in the bone marrow. It is usually a paraneoplastic syndrome, associated most commonly with large-cell granular lymphocyte leukemia but also thymoma. For patients who present both pure red cell aplasia and thymoma, thymectomy leads to an initial remission of the aplasia in 30% of cases. However, sustained remission may require the addition of medications such as corticosteroids, cyclospo­rine, or cyclophosphamide. We present a case of pure red cell aplasia associated with a thymoma in an otherwise healthy 80 year-old woman.

  4. A fully spray-coated fuel cell membrane electrode assembly using Aquivion ionomer with a graphene oxide/cerium oxide interlayer

    Science.gov (United States)

    Breitwieser, Matthias; Bayer, Thomas; Büchler, Andreas; Zengerle, Roland; Lyth, Stephen M.; Thiele, Simon

    2017-05-01

    A novel multilayer membrane electrode assembly (MEA) for polymer electrolyte membrane fuel cells (PEMFCs) is fabricated in this work, within a single spray-coating device. For the first time, direct membrane deposition is used to fabricate a PEMFC by spraying the short-side-chain ionomer Aquivion directly onto the gas diffusion electrodes. The fully sprayed MEA, with an Aquivion membrane 10 μm in thickness, achieved a high power density of 1.6 W/cm2 for H2/air operation at 300 kPaabs. This is one of the highest reported values for thin composite membranes operated in H2/air atmosphere. By the means of confocal laser scanning microscopy, individual carbon fibers from the gas diffusion layer are identified to penetrate through the micro porous layer (MPL), likely causing a low electrical cell resistance in the range of 150 Ω cm2 through the thin sprayed membranes. By spraying a 200 nm graphene oxide/cerium oxide (GO/CeO2) interlayer between two layers of Aquivion ionomer, the impact of the electrical short is eliminated and the hydrogen crossover current density is reduced to about 1 mA/cm2. The peak power density of the interlayer-containing MEA drops only by 10% compared to a pure Aquivion membrane of similar thickness.

  5. Effect of cerium additive and secondary phase analysis on Ag0.5Bi0.5TiO3 ceramics

    Indian Academy of Sciences (India)

    S Supriya; Antonio J Dos Santos-García; F Fernández-Martinez

    2016-02-01

    Cerium-doped silver bismuth titanate—Ag0.5Bi0.5TiO3 (ABT) ceramics have been synthesized by the high-temperature solid-state reaction method. The structure and elemental examination of the prepared ceramic was analysed by X-ray diffraction (XRD), Fourier transform infrared, scanning electron microscopy and energydispersive spectroscopy. XRD analysis showed the presence of pyrochlore structure and secondary phase when more than 5 mol% cerium was added. The impact of temperature on cerium-doped silver bismuth titanate samples was analysed by differential thermal analysis and differential scanning calorimetry. Cerium doping caused the flaky morphology comparing with undoped sample. The homogeneity of all the samples was discussed in detail by diffuse reflectance spectrum. This is the first time the reflection process is analysed for the cerium-doped ABT system to the best of our knowledge.

  6. Reactive removal of 2-chloroethyl ethyl sulfide vapors under visible light irradiation by cerium oxide modified highly porous zirconium (hydr) oxide

    Science.gov (United States)

    Mitchell, Joshua K.; Arcibar-Orozco, Javier A.; Bandosz, Teresa J.

    2016-12-01

    Highly porous cerium oxide modified Zr(OH)4 samples were synthesized using a simple one stage urea precipitation method. The amorphicity level of zirconium hydroxide did not change upon addition of cerium oxide particles. A unique aspect of the cerium oxide-modified materials is the presence of both the oxide (CeO2) and hydroxide (Zr(OH)4) phases resulting in a unique microporous structure of the final material. Extensive characterization using various chemical and physical methods revealed significant differences in the surface features. All synthesized materials were microporous and small additions of cerium oxide affected the surface chemistry. These samples were found as effective catalysts for a decontamination of mustard gas surrogate, 2-chloroethyl ethyl sulfide (CEES). Cerium oxide addition significantly decreased the band gap of zirconium hydroxide. Ethyl vinyl sulfide and 1,2-bis (Ethyl thio) ethane were identified as surface reaction products.

  7. Assembly of large purely inorganic Ce-stabilized/bridged selenotungstates: from nanoclusters to layers.

    Science.gov (United States)

    Chen, Wei-Chao; Qin, Chao; Li, Yang-Guang; Zang, Hong-Ying; Shao, Kui-Zhan; Su, Zhong-Min; Wang, En-Bo

    2015-05-01

    A versatile one-pot strategy was used to synthesize two large, purely inorganic selenotungstates, nanocluster K(6)Na(16) [Ce(6)Se(6)W(67)O(230) (OH)(6) (H(2)O)(17)]⋅47 H(2)O (1) and layer K(9)Na(5) Ce(H(2)O)(4) [Ce(6)Se(10)W(51)O(187) (OH)(7) (H(2)O)(18)]⋅45H(2)O(2), by combining cerium centers and SeO(3) (2-) heteroanion templates. Compound 1 displays a Ce-stabilized hexameric nanocluster with one rhombus-like {W(4)O(15) (OH)(3)} unit in the center, whereas compound 2 is the first example of a Ce-bridged layer selenotungstate network based on linkage of the unusual {Ce(6)Se(10)W(51)O(187) (OH)(7) (H(2)O)(18)} clusters and additional Ce(H(2)O)(4) fragments via Ce-O-Se bridges. The compounds were characterized by elemental analyses, IR spectroscopy, thermogravimetric analyses, powder and single-crystal X-ray diffraction, and electrospray ionization mass spectrometry. Moreover, the electrochemical property of compound 1 was also investigated. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Carbon dioxide and climate

    Energy Technology Data Exchange (ETDEWEB)

    1990-10-01

    Scientific and public interest in greenhouse gases, climate warming, and global change virtually exploded in 1988. The Department's focused research on atmospheric CO{sub 2} contributed sound and timely scientific information to the many questions produced by the groundswell of interest and concern. Research projects summarized in this document provided the data base that made timely responses possible, and the contributions from participating scientists are genuinely appreciated. In the past year, the core CO{sub 2} research has continued to improve the scientific knowledge needed to project future atmospheric CO{sub 2} concentrations, to estimate climate sensitivity, and to assess the responses of vegetation to rising concentrations of CO{sub 2} and to climate change. The Carbon Dioxide Research Program's goal is to develop sound scientific information for policy formulation and governmental action in response to changes of atmospheric CO{sub 2}. The Program Summary describes projects funded by the Carbon Dioxide Research Program during FY 1990 and gives a brief overview of objectives, organization, and accomplishments.

  9. Reaction products of chlorine dioxide.

    Science.gov (United States)

    Stevens, A A

    1982-01-01

    Inspection of the available literature reveals that a detailed investigation of the aqueous organic chemistry of chlorine dioxide and systematic identification of products formed during water disinfection has not been considered. This must be done before an informed assessment can be made of the relative safety of using chlorine dioxide as a disinfectant alternative to chlorine. Although trihalomethanes are generally not formed by the action of chlorine dioxide, the products of chlorine dioxide treatment of organic materials are oxidized species, some of which also contain chlorine. The relative amounts of species types may depend on the amount of chlorine dioxide residual maintained and the concentration and nature of the organic material present in the source water. The trend toward lower concentrations of chlorinated by-products with increasing ClO2 concentration, which was observed with phenols, has not been observed with natural humic materials as measured by the organic halogen parameter. Organic halogen concentrations have been shown to increase with increasing chlorine dioxide dose, but are much lower than those observed when chlorine is applied. Aldehydes have been detected as apparent by-products of chlorine dioxide oxidation reactions in a surface water that is a drinking water source. Some other nonchlorinated products of chlorine dioxide treatment may be quinones and epoxides. The extent of formation of these moieties within the macromolecular humic structure is also still unknown. PMID:7151750

  10. Atomic model of liquid pure Fe

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Using a θ-θX-ray diffractometer, the liquid structure of pure Fewas investigated and the diffraction intensity, structure factor, pair distribution function as well as the coordination number and atomic distance were obtained. The experimental results showed that there was also a pre-peak on the curve of the structure factor of liquid pure Fe. The pre-peak is a mark of medium-range order in melts. According to the characteristics of pre-peak, an atomic model of liquid pure Fe is constructed, namely, the structure of liquid pure Fe is a combination of clusters consisting of bcc cells with shared vertexes and other atoms with random dense atom distribution.

  11. Entropy product measure for multipartite pure states

    Institute of Scientific and Technical Information of China (English)

    CAO Wancang; LIU Dan; PAN Feng; LONG Guilu

    2006-01-01

    An entanglement measure for multipartite pure states is formulated using the product of the von Neumann entropy of the reduced density matrices of the constituents.Based on this new measure, all possible ways of the maximal entanglement of the triqubit pure states are studied in detail and all types of the maximal entanglement have been culate the degree of entanglement, and an improvement is given in the area near the zero entropy.

  12. Diphenylhydantoin-induced pure red cell aplasia.

    Science.gov (United States)

    Rusia, Usha; Malhotra, Purnima; Joshi, Panul

    2006-01-01

    Pure red cell aplasia is an uncommon complication of diphenylhydantoin therapy. It has not been reported in Indian literature. Awareness of the entity helps in establishing the cause of anaemia in these patients and alerts the physicians to the need of comprehensive haematological monitoring in these patients. A case of 58-year-old male who developed pure red cell aplasia following three months of diphenylhydantoin therapy is reported here.

  13. Expander Graphs in Pure and Applied Mathematics

    OpenAIRE

    Lubotzky, Alexander

    2011-01-01

    Expander graphs are highly connected sparse finite graphs. They play an important role in computer science as basic building blocks for network constructions, error correcting codes, algorithms and more. In recent years they have started to play an increasing role also in pure mathematics: number theory, group theory, geometry and more. This expository article describes their constructions and various applications in pure and applied mathematics.

  14. Dark fermentation on biohydrogen production: Pure culture.

    Science.gov (United States)

    Lee, Duu-Jong; Show, Kuan-Yeow; Su, Ay

    2011-09-01

    Biohydrogen is regarded as an attractive future clean energy carrier due to its high energy content and environmental-friendly conversion. While biohydrogen production is still in the early stage of development, there have been a variety of laboratory- and pilot-scale systems developed with promising potential. This work presents a review of literature reports on the pure hydrogen-producers under anaerobic environment. Challenges and perspective of biohydrogen production with pure cultures are also outlined.

  15. Crystallization behavior of electroless Co-Ni-B alloy plated in magnetic field in presence of cerium

    Institute of Scientific and Technical Information of China (English)

    XUAN Tian-peng; ZHANG Lei; HUANG Qin-hua

    2006-01-01

    The electrochemical property, chemical composition and crystal structure of electroless Co-Ni-B-Ce alloy plated in general state as well as in magnetic field were studied using potentiometer, plasma emission spectrometer, X-ray diffractometer,transmission electron microscope. The results show that the static potential and polarizability of electroless Co-Ni-B alloy are remarkably improved as the plating is carried out in magnetic field in the presence of a little amount of cerium in plating bath.Because of the action of magnetic field and rare earth element cerium, the boron content in alloy decreases, while cobalt and nickel contents increase. As a result, the amorphous Co-Ni-B alloy transforms to the microcrystalline Co-Ni-B-Ce alloy when the plating is in general state, and the Co-Ni-B alloy makes a crystalline transformation because of the action of magnetic field and rare earth element cerium.

  16. Determination of Ideal Broth Formulations Needed to Prepare Hydrous Cerium Oxide Microspheres via the Internal Gelation Process

    Energy Technology Data Exchange (ETDEWEB)

    Collins, Jack Lee [ORNL; Chi, Anthony [ORNL

    2009-02-01

    A simple test tube methodology was used to determine optimum process parameters for preparing hydrous cerium oxide microspheres via the internal gelation process.1 Broth formulations of cerium ammonium nitrate [(NH4)2Ce(NO3)6], hexamethylenetetramine, and urea were found that can be used to prepare hydrous cerium oxide gel spheres in the temperature range of 60 to 90 C. A few gel-forming runs were made in which microspheres were prepared with some of these formulations to be able to equate the test-tube gelation times to actual gelation times. These preparations confirmed that the test-tube methodology is reliable for determining the ideal broth formulations.

  17. Catalytic activity of cerium-doped Ru/Al2O3 during ozonation of dimethyl phthalate

    Institute of Scientific and Technical Information of China (English)

    Yunrui ZHOU; Wanpeng ZHU; Xun CHEN

    2008-01-01

    In this paper, factors influencing the mineraliza-tion of dimethyl phthalate (DMP) during catalytic ozona-tion with a cerium-doped Ru/Al2O3 catalyst were studied. The catalytic contribution was calculated through the results of a companrison experiment. It showed that doping cerium significantly enhanced catalytic activity. The total organic carbon (TOC) removal over the doped catalyst at 100 rain reached 75.1%, 61.3% using Ru/Al2O3 catalyst and only 14.0% using ozone alone. Catalytic activity reached the maximum when 0.2% of ruthenium and 1.0% of cerium'were simultaneously loaded onto Al2O3 support. Results of experiments on oxidation by ozone alone, adsorption of the catalyst, Ce ion's and heterogeneous catalytic ozonation confirmed that the contribution of het-erogeneous catalytic ozonation was about 50%, which showed the obvious effect of Ru-Ce/Al2O3 on catalytic activity.

  18. Corrosion resistance of flaky aluminum pigment coated with cerium oxides/hydroxides in chloride and acidic electrolytes

    Science.gov (United States)

    Niroumandrad, S.; Rostami, M.; Ramezanzadeh, B.

    2015-12-01

    The objective of this study was to enhance the corrosion resistance of lamellar aluminum pigment through surface treatment by cerium oxides/hydroxides. The surface composition of the pigments was studied by energy-dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The corrosion resistance of the pigment was evaluated by conventional hydrogen evolution measurements in acidic solution and electrochemical impedance spectroscopy (EIS) in 3.5% NaCl solution. Results showed that the Ce-rich coating composed of Ce2O3 and CeO2 was precipitated on the pigment surface after immersion in the cerium solution. The corrosion resistance of pigment was significantly enhanced after modification with cerium layer.

  19. Single crystal fiber growth of cerium doped strontium yttrate, SrY2O4:Ce3+

    Science.gov (United States)

    Philippen, J.; Guguschev, C.; Klimm, D.

    2017-02-01

    First single crystal fibers of cerium doped strontium yttrate were fabricated using the laser-heated pedestal growth technique. Through thermodynamic equilibrium calculations and by high-temperature mass spectrometry suitable growth conditions could be determined. The atmosphere played an important role during crystallization. It affected the composition shift, on the one hand, and the valence state of cerium, on the other hand. These dependencies can be explained by combining X-ray diffraction, elemental analysis, and optical spectroscopy. Crystallization in slightly reducing nitrogen atmosphere proved to be a reasonable choice, because evaporation is suppressed and trivalent cerium is stabilized. Strong green emission that depends on the oxygen fugacity during crystallization could be excited using UV light. Optical properties of SrY2O4:Ce3+ were measured for the first time.

  20. Ab initio molecular dynamics study of the properties of cerium in liquid sodium at 1000 K temperature

    Energy Technology Data Exchange (ETDEWEB)

    Samin, Adib; Li, Xiang; Zhang, Jinsuo [Nuclear Engineering Program, Department of Mechanical and Aerospace Engineering, The Ohio State University, 201 W 19th Avenue, Columbus, Ohio 43210 (United States); Mariani, R. D. [Idaho National Laboratory, Materials and Fuels Complex, Idaho Falls, Idaho 83415 (United States); Unal, Cetin [Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, New Mexico 87545 (United States)

    2015-12-21

    For liquid-sodium-cooled fast nuclear reactor systems, it is crucial to understand the behavior of lanthanides and other potential fission products in liquid sodium or other liquid metal solutions such as liquid cesium-sodium. In this study, we focus on lanthanide behavior in liquid sodium. Using ab initio molecular dynamics, we found that the solubility of cerium in liquid sodium at 1000 K was less than 0.78 at. %, and the diffusion coefficient of cerium in liquid sodium was calculated to be 5.57 × 10{sup −9} m{sup 2}/s. Furthermore, it was found that cerium in small amounts may significantly alter the heat capacity of the liquid sodium system. Our results are consistent with the experimental results for similar materials under similar conditions.

  1. Ab initio molecular dynamics study of the properties of cerium in liquid sodium at 1000 K temperature

    Science.gov (United States)

    Samin, Adib; Li, Xiang; Zhang, Jinsuo; Mariani, R. D.; Unal, Cetin

    2015-12-01

    For liquid-sodium-cooled fast nuclear reactor systems, it is crucial to understand the behavior of lanthanides and other potential fission products in liquid sodium or other liquid metal solutions such as liquid cesium-sodium. In this study, we focus on lanthanide behavior in liquid sodium. Using ab initio molecular dynamics, we found that the solubility of cerium in liquid sodium at 1000 K was less than 0.78 at. %, and the diffusion coefficient of cerium in liquid sodium was calculated to be 5.57 × 10-9 m2/s. Furthermore, it was found that cerium in small amounts may significantly alter the heat capacity of the liquid sodium system. Our results are consistent with the experimental results for similar materials under similar conditions.

  2. Implementation of a complex multi-phase equation of state for cerium and its correlation with experiment

    Energy Technology Data Exchange (ETDEWEB)

    Cherne, Frank J [Los Alamos National Laboratory; Jensen, Brian J [Los Alamos National Laboratory; Elkin, Vyacheslav M [VNIITF

    2009-01-01

    The complexity of cerium combined with its interesting material properties makes it a desirable material to examine dynamically. Characteristics such as the softening of the material before the phase change, low pressure solid-solid phase change, predicted low pressure melt boundary, and the solid-solid critical point add complexity to the construction of its equation of state. Currently, we are incorporating a feedback loop between a theoretical understanding of the material and an experimental understanding. Using a model equation of state for cerium we compare calculated wave profiles with experimental wave profiles for a number of front surface impact (cerium impacting a plated window) experiments. Using the calculated release isentrope we predict the temperature of the observed rarefaction shock. These experiments showed that the release state occurs at different magnitudes, thus allowing us to infer where dynamic {gamma} - {alpha} phase boundary is.

  3. Rehabilitation of pure alexia: A review

    Science.gov (United States)

    Starrfelt, Randi; Ólafsdóttir, Rannveig Rós; Arendt, Ida-Marie

    2013-01-01

    Acquired reading problems caused by brain injury (alexia) are common, either as a part of an aphasic syndrome, or as an isolated symptom. In pure alexia, reading is impaired while other language functions, including writing, are spared. Being in many ways a simple syndrome, one would think that pure alexia was an easy target for rehabilitation efforts. We review the literature on rehabilitation of pure alexia from 1990 to the present, and find that patients differ widely on several dimensions, such as alexia severity and associated deficits. Many patients reported to have pure alexia in the reviewed studies, have associated deficits such as agraphia or aphasia and thus do not strictly conform to the diagnosis. Few studies report clear and generalisable effects of training, none report control data, and in many cases the reported findings are not supported by statistics. We can, however, tentatively conclude that Multiple Oral Re-reading techniques may have some effect in mild pure alexia where diminished reading speed is the main problem, while Tacile-Kinesthetic training may improve letter identification in more severe cases of alexia. There is, however, still a great need for well-designed and controlled studies of rehabilitation of pure alexia. PMID:23808895

  4. Corrosion protection properties and interfacial adhesion mechanism of an epoxy/polyamide coating applied on the steel surface decorated with cerium oxide nanofilm: Complementary experimental, molecular dynamics (MD) and first principle quantum mechanics (QM) simulation methods

    Science.gov (United States)

    Bahlakeh, Ghasem; Ramezanzadeh, Bahram; Saeb, Mohammad Reza; Terryn, Herman; Ghaffari, Mehdi

    2017-10-01

    The effect of cerium oxide treatment on the corrosion protection properties and interfacial interaction of steel/epoxy was studied by electrochemical impedance spectroscopy, (EIS) classical molecular dynamics (MD) and first principle quantum mechanics (QM) simulation methods X-ray photoelectron spectroscopy (XPS) was used to verify the chemical composition of the Ce film deposited on the steel. To probe the role of the curing agent in epoxy adsorption, computations were compared for an epoxy, aminoamide and aminoamide modified epoxy. Moreover, to study the influence of water on interfacial interactions the MD simulations were executed for poly (aminoamide)-cured epoxy resin in contact with the different crystallographic cerium dioxide (ceria, CeO2) surfaces including (100), (110), and (111) in the presence of water molecules. It was found that aminoamide-cured epoxy material was strongly adhered to all types of CeO2 substrates, so that binding to ceria surfaces followed the decreasing order CeO2 (111) > CeO2 (100) > CeO2 (110) in both dry and wet environments. Calculation of interaction energies noticed an enhanced adhesion to metal surface due to aminoamide curing of epoxy resin; where facets (100) and (111) revealed electrostatic and Lewis acid-base interactions, while an additional hydrogen bonding interaction was identified for CeO2 (110). Overall, MD simulations suggested decrement of adhesion to CeO2 in wet environment compared to dry conditions. Additionally, contact angle, pull-off test, cathodic delamination and salt spray analyses were used to confirm the simulation results. The experimental results in line with modeling results revealed that Ce layer deposited on steel enhanced substrate surface free energy, work of adhesion, and interfacial adhesion strength of the epoxy coating. Furthermore, decrement of adhesion of epoxy to CeO2 in presence of water was affirmed by experimental results. EIS results revealed remarkable enhancement of the corrosion

  5. Effect of ultrasound on the structural and textural properties of copper-impregnated cerium-modified zirconium-pillared bentonite

    Science.gov (United States)

    Tomul, Fatma

    2011-12-01

    In this study, the synthesis of zirconium-pillared bentonite modified with cerium was performed via two different methods by the application of conventional and ultrasonic treatments during the intercalation stage. To synthesise copper-impregnated pillared clays by wet impregnation, cerium-modified zirconium-pillared clays were used as supportive materials after being calcined at 300 °C. Ultrasonic treatment significantly decreased the required processing time compared with the conventional treatment of the synthesised pillared bentonites. Chemical analysis confirmed the incorporation of Zr 4+, Ce 4+ and Cu 2+ species into the pillared bentonites. X-ray diffraction (XRD) patterns of zirconium- and cerium/zirconium-pillared bentonites prepared by conventional treatment show that one large d-spacing above 3.5 nm corresponds to the mesoporous delaminated part, and another small d-spacing above 1.7 nm is indicative of the microporous pillared part. Zirconium- and cerium/zirconium-pillared bentonites prepared via ultrasonic treatment exhibited similar results, with the same high d-spacing but with a second low-intensity d-spacing above 1.9 nm. The delaminated structures of the pillared bentonites synthesised by both methods were conserved after copper impregnation. Nitrogen-adsorption isotherm analysis showed that the textural characteristics of products synthesised by ultrasonic treatment were comparable to those of products synthesised by conventional treatment. Fourier-transform infrared spectroscopy (FTIR) analyses showed the presence of Brønsted- and Lewis-acid sites, and zirconium-pillared clays synthesised by conventional treatment exhibited increased numbers of Brønsted- and Lewis-acid sites after cerium addition and copper impregnation. However, the products synthesised by ultrasonic treatment exhibited an increased number of Brønsted- and Lewis-acid sites after cerium addition, but a decreased number of acid sites after copper impregnation.

  6. TREATMENT OF HYDROCARBON, ORGANIC RESIDUE AND PRODUCTION CHEMICAL DAMAGE MECHANISMS THROUGH THE APPLICATION OF CARBON DIOXIDE IN NATURAL GAS STORAGE WELLS

    Energy Technology Data Exchange (ETDEWEB)

    Lawrence J. Pekot; Ron Himes

    2004-05-31

    Core specimens and several material samples were collected from two natural gas storage reservoirs. Laboratory studies were performed to characterize the samples that were believed to be representative of a reservoir damage mechanism previously identified as arising from the presence of hydrocarbons, organic residues or production chemicals. A series of laboratory experiments were performed to identify the sample materials, use these materials to damage the flow capacity of the core specimens and then attempt to remove or reduce the induced damage using either carbon dioxide or a mixture of carbon dioxide and other chemicals. Results of the experiments showed that pure carbon dioxide was effective in restoring flow capacity to the core specimens in several different settings. However, in settings involving asphaltines as the damage mechanism, both pure carbon dioxide and mixtures of carbon dioxide and other chemicals provided little effectiveness in damage removal.

  7. Influence of agglomeration of cerium oxide nanoparticles and speciation of cerium(III) on short term effects to the green algae Chlamydomonas reinhardtii.

    Science.gov (United States)

    Röhder, Lena A; Brandt, Tanja; Sigg, Laura; Behra, Renata

    2014-07-01

    Cerium oxide nanoparticles (CeO2 NP) are increasingly used in industrial applications and may be released to the aquatic environment. The fate of CeO2 NP and effects on algae are largely unknown. In this study, the short term effects of CeO2 NP in two different agglomeration states on the green algae Chlamydomonas reinhardtii were examined. The role of dissolved cerium(III) on toxicity, its speciation and the dissolution of CeO2 NP were considered. The role of cell wall of C. reinhardtii as a barrier and its influence on the sensitivity to CeO2 NP and cerium(III) was evaluated by testing both, the wild type and the cell wall free mutant of C. reinhardtii. Characterization showed that CeO2 NP had a surface charge of ∼0mV at physiological pH and agglomerated in exposure media. Phosphate stabilized CeO2 NP at pH 7.5 over 24h. This effect was exploited to test CeO2 NP dispersed in phosphate with a mean size of 140nm and agglomerated in absence of phosphate with a mean size of 2000nm. The level of dissolved cerium(III) in CeO2 NP suspensions was very low and between 0.1 and 27nM in all tested media. Exposure of C. reinhardtii to Ce(NO3)3 decreased the photosynthetic yield in a concentration dependent manner with EC50 of 7.5±0.84μM for wild type and EC50 of 6.3±0.53μM for the cell wall free mutant. The intracellular level of reactive oxygen species (ROS) increased upon exposure to Ce(NO3)3 with effective concentrations similar to those inhibiting photosynthesis. The agglomerated CeO2 NP caused a slight decrease of photosynthetic yield at the highest concentrations (100μM), while no effect was observed for dispersed CeO2 NP. The low toxicity of agglomerated CeO2 NP was attributed quantitatively to Ce(3+) ions co-occurring in the nanoparticle suspension whereas for dispersed CeO2 NP, dissolved Ce(3+) was precipitated with phosphate and not bioavailable. Furthermore CeO2 NP did not affect the intracellular ROS level. The cell wall free mutant and wild type of C

  8. Trinitratobis{N'-[1-(2-pyridyl)ethylidene]isonicotinohydrazide}cerium(III): a three-dimensional cerium-organic supramolecular structure.

    Science.gov (United States)

    Zhang, Ying Ying; Liu, Shi Xiong

    2009-07-01

    The Ce(III) ion in the title complex, [Ce(NO(3))(3)(C(13)H(12)N(4)O)(2)], is 12-coordinated by six chelating nitrate O atoms and six donors (2 O and 4 N atoms) of two N'-[1-(2-pyridyl)ethylidene]isonicotinohydrazide ligands, exhibiting a bicapped pentagonal-antiprism-type coordination geometry. The title complex possesses C(2) point symmetry and is located on a twofold crystallographic axis. Each molecule is linked with four surrounding molecules by four N-H...N hydrogen bonds, resulting in an extended two-dimensional layer parallel to the ab plane, while pi-pi interactions between pyridine rings from neighboring complex molecules connect the two-dimensional layers into a three-dimensional cerium-organic supramolecular structure.

  9. Optical and structural characterisation of pure and Pr{sup 3+} doped LaPO{sub 4} and CePO{sub 4} nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Macalik, L., E-mail: L.Macalik@int.pan.wroc.pl [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, ul. Okolna 2, 50-422 Wroclaw (Poland); Tomaszewski, P.E. [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, ul. Okolna 2, 50-422 Wroclaw (Poland); Matraszek, A.; Szczygiel, I. [Department of Inorganic Chemistry, Faculty of Engineering and Economics, Wroclaw University of Economics, ul. Komandorska 118/120, 53-345 Wroclaw (Poland); Solarz, P. [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, ul. Okolna 2, 50-422 Wroclaw (Poland); Godlewska, P. [Department of Bioorganic Chemistry, Faculty of Engineering and Economics, Wroclaw University of Economics, ul. Komandorska 118/120, 53-345 Wroclaw (Poland); Sobczyk, M. [Faculty of Chemistry, University of Wroclaw, ul. F. Joliot-Curie 14, 50-383 Wroclaw (Poland); Hanuza, J. [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, ul. Okolna 2, 50-422 Wroclaw (Poland); Department of Bioorganic Chemistry, Faculty of Engineering and Economics, Wroclaw University of Economics, ul. Komandorska 118/120, 53-345 Wroclaw (Poland)

    2011-07-07

    Highlights: > The nanoparticles (12-30 nm) of hydrated (hexagonal) and water-free (monoclinic) phases of lanthanum and cerium orthophosphates La(Ce)PO{sub 4} were obtained by the hydrothermal method. > Differences between hexagonal and monoclinic nanocrystals are very well reflected in the vibrational spectra and a slight influence of the environment conditions (pH) of the crystallisation is found. > The structure differences and environment conditions of the crystallisation (pH) play role in the luminescent properties. - Abstract: The rod- and stick-shaped nanocrystalline cerium and lanthanum orthophosphates, pure and Pr{sup 3+} doped, have been synthesised by the hydrothermal method in acidic (pH 1) or alkaline (pH 11) environment. Subsequent calcination of as-obtained powders at different temperatures, 500 and 900 deg. C, led to the formation of hexagonal and monoclinic phases, respectively. The hexagonal phase at room temperature has been identified as hydrated orthophosphate with zeolite water inside the channels of the structure. The monoclinic phase is free of water. The average grain size is about 12-30 nm depending on the calcination temperature and preparation conditions. The structural, morphological and optical (vibrational and luminescent) properties have been characterised and their changes due to the temperature and different acidity in the starting materials have been studied.

  10. Electronic, structural, and thermodynamic properties of actinide dioxides

    Science.gov (United States)

    Ma, Li; Atta-Fynn, Raymond; Ray, Asok K.

    2010-03-01

    As a continuation of our studies of pure actinide metals using hybrid density functional theory,footnotetextR. Atta-Fynn and A. K. Ray, Europhysics Letters, 85, 27008-p1- p6 (2009); Chemical Physics Letters, 482, 223-227 (2009). we present here a systematic study of the electronic and geometric structure properties of the actinide dioxides, UO2, PuO2 and AmO2, using both density functional and hybrid density functional theories. For the hybrid density functionals, the fractions of exact Hartree-Fock exchange used were 25% and 40%. Each compound has been studied at the nonmagnetic, ferromagnetic and antiferromagnetic configurations, with and without spin-orbit coupling (SOC). The influence of SOC on the properties of the actinide dioxides will be discussed. Thermodynamic properties such as phonon dispersion curves, heat capacity, entropy, internal energy and free energy have been calculated by a coupling of first-principles calculations and lattice dynamics.

  11. Equivalent Activity Coefficient Phenomenon of Cerium Reacting with Lead or Bismuth in Ag, Cu and Zn Alloy

    Institute of Scientific and Technical Information of China (English)

    薛松柏; 钱乙余; 董健

    2002-01-01

    The relation between contents of cerium and impurity lead or bismuth to their activity coefficient in Ag, Cu and Zn-base alloy was calculated and analyzed by using the ternary system Chou model. The thermodynamic calculation results show that the "equivalent activity coefficient phenomenon" emerges among the activity coefficient of solute in a certain range of cerium (or at a certain point) for the Ce-Pb-X and Ce-Bi-X (X=Ag, Cu or Zn) ternary alloy system. Under this condition, the activity coefficient of solute has nothing to do with its own concentration. The preliminary theoretical analysis to this phenomenon was also made.

  12. Improvement of corrosion resistance of AZ31 Mg alloy by anodizing with co-precipitation of cerium oxide

    Institute of Scientific and Technical Information of China (English)

    Salah Abdelghany SALMAN; Ryoichi ICHINO; Masazumi OKIDO

    2009-01-01

    Anodizing of AZ31 Mg alloy in NaOH solution by co-precipitation of cerium oxide was investigated. The chemical composition and phase structure of the coating film were determined via optical microscopy, SEM and XRD. The corrosion properties of the anodic film were characterized by using potentiodynamic polarization curves in 17 mmol/L NaCl and 0.1 mol/L Na2SO4 solution at 298 K. The corrosion resistance of AZ31 magnesium alloy is significantly improved by adding cerium oxide to alkaline solution. In addition, the surface properties are enhanced and the film contains no crack.

  13. Catalytic wet peroxidation of pyridine bearing wastewater by cerium supported SBA-15

    Energy Technology Data Exchange (ETDEWEB)

    Subbaramaiah, V. [Department of Chemical Engineering, Indian Institute of Technology Roorkee, Roorkee 247667 Uttarakhand (India); Srivastava, Vimal Chandra, E-mail: vimalcsr@yahoo.co.in [Department of Chemical Engineering, Indian Institute of Technology Roorkee, Roorkee 247667 Uttarakhand (India); Mall, Indra Deo [Department of Chemical Engineering, Indian Institute of Technology Roorkee, Roorkee 247667 Uttarakhand (India)

    2013-03-15

    Highlights: ► Cerium supported SBA-15 (Ce/SBA-15) synthesized by two-step synthesis. ► Characterization of Ce/SBA-15 by FTIR, XRD and BET surface area. ► Catalytic peroxidation of pyridine by Ce/SBA-15. ► Optimization of parameters like catalyst dose, H{sub 2}O{sub 2} dose, initial concentration and temperature. ► Catalyst reusability and leaching study performed. -- Abstract: Cerium supported SBA-15 (Ce/SBA-15) was synthesized by two-step synthesis method in acidic medium. It was further characterized by various characterization techniques such as X-ray diffraction, field-emission scanning electron microscopy, Fourier transform infrared spectroscopy and N{sub 2} adsorption–desorption pore size distribution analysis. The Ce/SBA-15 showed highly ordered meso-structure with pore diameter ≈ 70–100 A and pore volume ≈ 0.025 cm{sup 3}/g. Ce/SBA-15 was further evaluated as a catalyst for the oxidation of highly toxic and non-biodegradable material, pyridine, by catalytic wet-peroxidation method. The effects of various operating parameters such as catalyst dose (0.5–6 g/l), stoichiometric ratio of H{sub 2}O{sub 2}/pyridine (1–6), initial pyridine concentration (50–800 mg/l) and temperature (313–358 K) have been evaluated and optimized. Ce/SBA-15 showed stable performance during reuse for six cycles with negligible cerium leaching. Kinetic and thermodynamic parameters and operation cost have also been determined.

  14. Application of Cerium (IV as an Oxidimetric Agent for the Determination of Ethionamide in Pharmaceutical Formulations

    Directory of Open Access Journals (Sweden)

    Kanakapura Basavaiah

    2016-01-01

    Full Text Available Two simple methods are described for the determination of ethionamide (ETM in bulk drug and tablets using cerium (IV sulphate as the oxidimetric agent. In both methods, the sample solution is treated with a measured excess of cerium (IV solution in H2SO4 medium, and after a fixed standing time, the residual oxidant is determined either by back titration with standard iron (II solution to a ferroin end point in titrimetry or by reacting with o-dianisidine followed by measurement of the absorbance of the orange-red coloured product at 470 nm in spectrophotometry. In titrimetry, the reaction proceeded with a stoichiometry of 1 : 2 (ETM : Ce (IV and the amount of cerium (IV consumed by ETM was related to the latter’s amount, and the method was applicable over 1.0–8.0 mg of drug. In spectrophotometry, Beer’s law was obeyed over the concentration range of 0.5–5.0 μg/mL ETM with a molar absorptivity value of 2.66 × 104 L/(mol·cm. The limits of detection (LOD and quantification (LOQ calculated according to ICH guidelines were 0.013 and 0.043 μg/mL, respectively. The proposed titrimetric and spectrophotometric methods were found to yield reliable results when applied to bulk drug and tablets analysis, and hence they can be applied in quality control laboratories.

  15. Forecasting carbon dioxide emissions.

    Science.gov (United States)

    Zhao, Xiaobing; Du, Ding

    2015-09-01

    This study extends the literature on forecasting carbon dioxide (CO2) emissions by applying the reduced-form econometrics approach of Schmalensee et al. (1998) to a more recent sample period, the post-1997 period. Using the post-1997 period is motivated by the observation that the strengthening pace of global climate policy may have been accelerated since 1997. Based on our parameter estimates, we project 25% reduction in CO2 emissions by 2050 according to an economic and population growth scenario that is more consistent with recent global trends. Our forecasts are conservative due to that we do not have sufficient data to fully take into account recent developments in the global economy.

  16. Uranium dioxide electrolysis

    Science.gov (United States)

    Willit, James L [Batavia, IL; Ackerman, John P [Prescott, AZ; Williamson, Mark A [Naperville, IL

    2009-12-29

    This is a single stage process for treating spent nuclear fuel from light water reactors. The spent nuclear fuel, uranium oxide, UO.sub.2, is added to a solution of UCl.sub.4 dissolved in molten LiCl. A carbon anode and a metallic cathode is positioned in the molten salt bath. A power source is connected to the electrodes and a voltage greater than or equal to 1.3 volts is applied to the bath. At the anode, the carbon is oxidized to form carbon dioxide and uranium chloride. At the cathode, uranium is electroplated. The uranium chloride at the cathode reacts with more uranium oxide to continue the reaction. The process may also be used with other transuranic oxides and rare earth metal oxides.

  17. Trace electrochemical analysis of Europium, Ytterbium, and Cerium at their joint presence in solution

    Directory of Open Access Journals (Sweden)

    Rema Matakova

    2012-03-01

    Full Text Available In the course of several decades at the department of analytical chemistry and chemistry of rare elements there were studied the electrode processes with participation of rare-earth metals (REM in accordance with the long awaiting problem of the development of rare-metal and rare-earth branch of non-ferrous metallurgy of Kazakhstan. With the aim of express and highly sensitive analytical control of raw materials and final product of rare-earth industry there were developed the methods of inversion-voltamperometric determination of low concentrations of europium, ytterbium and cerium under the conditions of their individual and combined presence in the solution.

  18. Sequence-specific Hydrolysis of Single-stranded DNA by PNA-Cerium (Ⅳ) Adduct

    Institute of Scientific and Technical Information of China (English)

    He Bai SHEN; Feng WANG; Yong Tao YANG

    2005-01-01

    A novel artificial site specific cleavage reagent, with peptide nucleic acid (PNA) as sequence-recognizing moiety and cerium (Ⅳ) ions as "scissors" for cleaving target DNA, was synthesized. Subsequently, it was employed in the cleavage of target 26-mer single-stranded DNA (ssDNA), which has 10-mer sequence complementary with PNA recognizer in the hybrids,under physiological conditions. Reversed-phase high-performance liquid chromatogram (RPHPLC) experiments indicated that the artificial site specific cleavage reagent could cleave the target DNA specifically.

  19. Surface structures of cerium oxide nanocrystalline particles from the size dependence of the lattice parameters

    Science.gov (United States)

    Tsunekawa, S.; Ito, S.; Kawazoe, Y.

    2004-10-01

    Cerium oxide nanocrystalline particles are synthesized and monodispersed in the size range from 2 to 8nm in diameter. The dependence of the lattice parameters on particle size is obtained by x-ray and electron diffraction analyses. The size dependence well coincides with the estimation based on the assumption that the surface is composed of one layer of Ce2O3 and the inside consists of CeO2. The effect of particle size on lattice parameters is discussed from the differences in the fabrication method and the surface structure.

  20. High-quality single-crystal growth and unique electronic states in cerium and uranium compounds

    Science.gov (United States)

    Onuki, Yoshichika; Settai, Rikio; Sugiyama, Kiyohiro; Inada, Yoshihiko; Takeuchi, Tetsuya; Haga, Yoshinori; Yamamoto, Etsuji; Harima, Hisatomo; Yamagami, Hiroshi

    2007-03-01

    We have grown many kinds of high-quality single crystals of cerium and uranium compounds and studied the Fermi surface properties via the de Haas-van Alphen experiments and energy band calculations. The quasi-two-dimensional electronic states are clarified in some compounds such as USb2, CeCoIn5, UPtGa5 and most likely UIr. In a ferromagnet CeRh3B2, we have found unique electronic states with quasi-one-dimensional character.

  1. A nonreciprocal racetrack resonator based on vacuum-annealed magnetooptical cerium-substituted yttrium iron garnet.

    Science.gov (United States)

    Goto, Taichi; Onbasli, Mehmet C; Kim, Dong Hun; Singh, Vivek; Inoue, M; Kimerling, Lionel C; Ross, C A

    2014-08-11

    Vacuum annealed polycrystalline cerium substituted yttrium iron garnet (CeYIG) films deposited by radio frequency magnetron sputtering on non-garnet substrates were used in nonreciprocal racetrack resonators. CeYIG annealed at 800°C for 30 min provided a large Faraday rotation angle, close to the single crystal value. Crystallinity, magnetic properties, refractive indices and absorption coefficients were measured. The resonant transmission peak of the racetrack resonator covered with CeYIG was non-reciprocally shifted by applying an in-plane magnetic field.

  2. Performance of a Tungsten-Cerium Fluoride Sampling Calorimeter in High-Energy Electron Beam Tests

    CERN Document Server

    Becker, R.; Dissertori, G.; Djambazov, L.; Donega, M.; Lustermann, W.; Marini, A.C.; Nessi-Tedaldi, F.; Pandolfi, F.; Peruzzi, M.; Schönenberger, M.; Cavallari, F.; Dafinei, I.; Diemoz, M.; Lope, C. Jorda; Meridiani, P.; Nuccetelli, M.; Paramatti, R.; Pellegrino, F.; Micheli, F.; Organtini, G.; Rahatlou, S.; Soffi, L.; Brianza, L.; Govoni, P.; Martelli, A.; Tabarelli de Fatis, T.; Monti, V.; Pastrone, N.; Trapani, P.P.; Candelise, V.; Della Ricca, G.

    2015-12-21

    A prototype for a sampling calorimeter made out of cerium fluoride crystals interleaved with tungsten plates, and read out by wavelength-shifting fibres, has been exposed to beams of electrons with energies between 20 and 150 GeV, produced by the CERN Super Proton Synchrotron accelerator complex. The performance of the prototype is presented and compared to that of a Geant4 simulation of the apparatus. Particular emphasis is given to the response uniformity across the channel front face, and to the prototype's energy resolution.

  3. UV-Shielding and Catalytic Characteristics of Nanoscale Zinc-Cerium Oxides

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Fine particles of zinc-cerium oxides (ZCO) used as an ultraviolet filter were prepared via combustion synthesis route. The catalytic activity, UV-shielding performance, surface modification and application of ZCO in polyester varnish were discussed in detail. The experimental results indicate that the photo-catalytic activity of ZCO is much smaller than these of ZnO and TiO2; the oxidation catalytic activity of ZCO is far lower than that of CeO2; the ZCO has shown excellent ultraviolet absorption in the range of UV;addition modified ZCO (MZCO) into polyester will enhance the UV-shielding capability of polyester.

  4. APPLICATIONS OF CERIUM BIS (MONOMYRISTY—LPHOSPHATE)ADSORBENT TO REVERSED PHASE LIQUID CHROMATOGRAPHY

    Institute of Scientific and Technical Information of China (English)

    SuZhengquan; FengHuixia; 等

    1996-01-01

    The tetravalent metal salts of monoalkyl phosphates [M(O3POR)2]are a new kind of stationary phases of Chromatography-homogeneous bonded phases.This paper deals with the application of cerium bis(monomyristylphosphate)as support to reversed phase liquid chromatography.The results show that the best mobil phase is CH3CN:H2O=95:5.The good separation to the mixture containing six aromatic hydrocarbons and the determination of naphthalene in a group samples have been achieved.The regression analysis shows that detect limits,linearities and precision for six aromatic hydrocarbons are good.

  5. ARTICLES: Photoinduced light scattering in cerium-doped barium strontium niobate crystals

    Science.gov (United States)

    Voronov, Valerii V.; Dorosh, I. R.; Kuz'minov, Yu S.; Tkachenko, N. V.

    1980-11-01

    Photoinduced light scattering was observed in cerium-doped (SrxBa1-x)1-y(Nb2O6)y crystals having the composition x = 0.61, y = 0.4993. It was found that this effect is due to holographic amplification of light scattered by crystal defects. An analysis is made of static and dynamic characteristics of self-amplification of scattered light in the crystals. A theoretical model of the process is constructed assuming that the hologram recording process is of the diffusion type. Theoretical results are compared with the experiment.

  6. Photoinduced light scattering in cerium-doped barium strontium niobate crystals

    Science.gov (United States)

    Voronov, V. V.; Dorosh, I. R.; Kuz'minov, Yu. S.; Tkachenko, N. V.

    Photoinduced light scattering was observed in cerium-doped (Srx Ba1-x)1-y(Nb2O6)y crystals having the composition x = 0.61, y = 0.4993. It was found that this effect is due to holographic amplification of light scattered by crystal defects. An analysis is made of static and dynamic characteristics of self-amplification of scattered light in the crystals. A theoretical model of the process is constructed assuming that the hologram recording process is of the diffusion type. Theoretical results are compared with the experiment.

  7. Performance of a tungsten–cerium fluoride sampling calorimeter in high-energy electron beam tests

    Energy Technology Data Exchange (ETDEWEB)

    Becker, R.; Bianchini, L.; Dissertori, G.; Djambazov, L.; Donega, M.; Lustermann, W.; Marini, A.C.; Nessi-Tedaldi, F. [Institut for Particle Physics, ETH Zurich (Switzerland); Pandolfi, F., E-mail: francesco.pandolfi@cern.ch [Institut for Particle Physics, ETH Zurich (Switzerland); Peruzzi, M.; Schönenberger, M. [Institut for Particle Physics, ETH Zurich (Switzerland); Cavallari, F.; Dafinei, I.; Diemoz, M.; Lope, C. Jorda; Meridiani, P.; Nuccetelli, M.; Paramatti, R.; Pellegrino, F. [INFN – Sezione di Roma (Italy); Micheli, F. [Dipartimento di Fisica “Sapienza”, Università di Roma e INFN – Sezione di Roma (Italy); and others

    2015-12-21

    A prototype for a sampling calorimeter made out of cerium fluoride crystals interleaved with tungsten plates, and read out by wavelength-shifting fibres, has been exposed to beams of electrons with energies between 20 and 150 GeV, produced by the CERN Super Proton Synchrotron accelerator complex. The performance of the prototype is presented and compared to that of a GEANT4 simulation of the apparatus. Particular emphasis is given to the response uniformity across the channel front face, and to the prototype's energy resolution.

  8. PVC-based 1,3,5-trithiane sensor for cerium(III) ions

    Science.gov (United States)

    Shamsipur; Yousefi; Ganjali

    2000-06-01

    A PVC membrane sensor for cerium(III) ions based on 1,3,5-trithiane as membrane carrier was prepared. The sensor has a linear dynamic range of 1.0 x 10(-1)-5.0 x 10(-5) M, with a Nernstian slope of 19.4+/-0.4 mV decade(-1), and a detection limit 3.0 x 10(-5) M. It has a fast response time of fluoride ions and in determination of F- ion in some mouth wash preparations.

  9. Spectroscopy of gadolinium gallium garnet doped with cerium under high hydrostatic pressure

    OpenAIRE

    2012-01-01

    Studies of the spectroscopic properties of Ce3+ dopant in bulk Gd3Ga5O12:Ce crystal under pressure are presented. In spite of strong inter-shell 4f ® 5d absorption bands at ambient pressure the cerium luminescence in Gd3Ga5O12 is entirely quenched even at low temperature. It has been shown that applying pressure allows for recovering the 5d ® 4f radiative transitions. Further increase of pressure improves the emission efficiency. This effect is analyzed in terms of two possible phenomen...

  10. [Study on synergistic effect of bactericidal effect of chlorine dioxide solution by surfactant].

    Science.gov (United States)

    Wang, Kuitao; Tian, Vuena; Gu, Na; Zhang, Congjing; Niu, Jiajing

    2013-03-01

    To study the effect of gemini fluorocarbon, sodium p-perfluorous nonenoxybenzene sulfonate and sodium dodecyl sulfate on the chlorine dioxide solution sterilization to object surface. Pure chlorine dioxide solution as the reference disinfectant, carrier quantitative bactericidal test and simulated test on-site were used to carry out laboratory observation according to The disinfection technical specifications (2002). Carrier quantitative bactericidal test showed that the addition dosage of gemini fluoronates, sodium dodecyl sulfate surfactant and perfluorinated the nonene oxy benzene sulfonate in disinfectant solution were 60, 60 and 40 mg/L respectively, the killing log value of Staphylococcus aureus exposed to the disinfectant solution containing chlorine dioxide 50 mg/L for 10 mm were all more than 3; and the addition dosage of gemini fluorinates, sodium dodecyl sulfate and perfluorinated the nonene oxy benzene sulfonate in disinfectant solution were 60 mg/L, the killing log value of Escherichia coli exposed to the disinfectant solution containing chlorine dixoxide 20 mg/L for 10 min were all more than 3. The bactericidal effect of the mixture use of surfactant and chlorine dioxide was better than the single use of chlorine dioxide. The simulated test on-site showed that the killing log value of Escherichia coli exposed to the disinfectant solution containing perfluorinated the nonene oxy benzene sulfonate 40 mg/L and chlorine dioxide 20 mg/L for 15 min was more than 3. Surface active agent on germicidal efficacy of chlorine dioxide solution had synergistic action.

  11. Nokia PureView oversampling technology

    Science.gov (United States)

    Vuori, Tero; Alakarhu, Juha; Salmelin, Eero; Partinen, Ari

    2013-03-01

    This paper describes Nokia's PureView oversampling imaging technology as well as the product, Nokia 808 PureView, featuring it. The Nokia PureView imaging technology is the combination of a large, super high resolution 41Mpix with high performance Carl Zeiss optics. Large sensor enables a pixel oversampling technique that reduces an image taken at full resolution into a lower resolution picture, thus achieving higher definition and light sensitivity. One oversampled super pixel in image file is formed by using many sensor pixels. A large sensor enables also a lossless zoom. If a user wants to use the lossless zoom, the sensor image is cropped. However, up-scaling is not needed as in traditional digital zooming usually used in mobile devices. Lossless zooming means image quality that does not have the digital zooming artifacts as well as no optical zooming artifacts like zoom lens system distortions. Zooming with PureView is also completely silent. PureView imaging technology is the result of many years of research and development and the tangible fruits of this work are exceptional image quality, lossless zoom, and superior low light performance.

  12. Structural anatomy of pure and hemianopic alexia.

    Science.gov (United States)

    Leff, A P; Spitsyna, G; Plant, G T; Wise, R J S

    2006-09-01

    The two most common types of acquired reading disorder resulting from damage to the territory of the dominant posterior cerebral artery are hemianopic and pure alexia. Patients with pronounced hemianopic alexia have a right homonymous hemianopia that encroaches into central or parafoveal vision; they read individual words well, but generate inefficient reading saccades when reading along a line of text. Patients with pure alexia also often have a hemianopia but are more disabled, making frequent errors on individual words; they have sustained damage to a brain region that supports efficient word identification. To investigate the differences in lesion site between hemianopic alexia and pure alexia groups, as rehabilitative techniques differ between the two conditions. High-resolution magnetic resonance images were obtained from seven patients with hemianopic alexia and from six patients with pure alexia caused by a left occipital stroke. The boundary of each lesion was defined and lesion volumes were then transformed into a standard stereotactic space so that regional comparisons could be made. The two patient groups did not differ in terms of damage to the medial left occipital lobe, but those with pure alexia had additional lateral damage to the posterior fusiform gyrus and adjacent tissue. Clinicians will be able to predict the type of reading disorder patients with left occipital lesions have from simple tests of reading speed and the distribution of damage to the left occipital lobe on brain imaging. This information will aid management decisions, including recommendations for reading rehabilitation.

  13. Pure plate bending in couple stress theories

    CERN Document Server

    Hadjesfandiari, Ali R; Dargush, Gary F

    2016-01-01

    In this paper, we examine the pure bending of plates within the framework of modified couple stress theory (M-CST) and consistent couple stress theory (C-CST). In this development, it is demonstrated that M-CST does not describe pure bending of a plate properly. Particularly, M-CST predicts no couple-stresses and no size effect for the pure bending of the plate into a spherical shell. This contradicts our expectation that couple stress theory should predict some size effect for such a deformation pattern. Therefore, this result clearly demonstrates another inconsistency of indeterminate symmetric modified couple stress theory (M-CST), which is based on considering the symmetric torsion tensor as the curvature tensor. On the other hand, the fully determinate skew-symmetric consistent couple stress theory (C-CST) predicts results for pure plate bending that tend to agree with mechanics intuition and experimental evidence. Particularly, C-CST predicts couple-stresses and size effects for the pure bending of the ...

  14. Lattice-Symmetry-Driven Phase Competition in Vanadium Dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Tselev, Alexander [ORNL; Luk' yanchuk, Prof. Igor A. [University of Picardie Jules Verne, Amiens, France; Ivanov, Ilia N [ORNL; Budai, John D [ORNL; Tischler, Jonathan Zachary [ORNL; Strelcov, Evgheni [Southern Illinois University; Kolmakov, Andrei [Southern Illinois University; Kalinin, Sergei V [ORNL

    2011-01-01

    We performed group-theoretical analysis of the symmetry relationships between lattice structures of R, M1, M2, and T phases of vanadium dioxide in the frameworks of the general Ginzburg-Landau phase transition theory. The analysis leads to a conclusion that the competition between the lower-symmetry phases M1, M2, and T in the metal-insulator transition is pure symmetry driven, since all the three phases correspond to different directions of the same multi-component structural order parameter. Therefore, the lower-symmetry phases can be stabilized in respect to each other by small perturbations such as doping or stress.

  15. Scintillation and Luminescence Properties of Undoped and Cerium-doped LiGdCl4 and NaGdCl4

    Energy Technology Data Exchange (ETDEWEB)

    Porter-Chapman, Yetta D.; Bourret-Courchesne, Edith D.; Bizarri, Gregory; Weber, Marvin J.; Derenzo, Stephen E.

    2008-10-05

    We report the scintillation properties of the undoped and cerium-doped variations of LiGdCl4 and NaGdCl4. Powder samples of these materials exhibit significant scintillation under X-rays. The samples were synthesized by solid-state methods from a 1:1 molar ratio of lithium or sodium chloride and gadolinium chloride. Cerium trichloride was used as the dopant. The physical, optical, and scintillation properties of these materials were analyzed by powder X-ray diffraction, photoluminescence, X-ray excited luminescence, and pulsed X-ray luminosity measurements. Increases in light yields are observed as the concentration of cerium increases. The highest light yields occurred at 20 percent cerium doping for both compounds. At larger concentrations neither compound formed, indicating a breakdown of the lattice with the addition of large amounts of cerium cations. At 20 percent cerium, LiGdCl4 and NaGdCl4 display scintillation light 3.6 times and 2.2 times the light yield of the reference material, YAlO3:Ce3+, respectively. Both emit in the ranges of 340 ? 350 nm and 365 - 370 nm and display multiexponential decays with cerium-like decay components at 33 ns (LiGdCl4:Ce) and 26 ns (NaGdCl4:Ce).

  16. Effects of cerium oxide supplementation to laying hen diets on performance, egg quality, some antioxidant enzymes in serum and lipid oxidation in egg yolk.

    Science.gov (United States)

    Bölükbaşı, S C; Al-Sagan, A A; Ürüşan, H; Erhan, M K; Durmuş, O; Kurt, N

    2016-08-01

    This study was conducted to determine the effects of dietary cerium oxide levels (0, 100, 200, 300 or 400 mg/kg) on the laying performance, egg quality, some blood serum parameters and egg lipid peroxidation of laying hen. In total, one hundred and twenty 22-week-old brown Lohman LSL laying hens were randomly assigned to five groups equally (n = 24). Each treatment was replicated six times. Dietary supplementation of cerium oxide had no significant effect on feed intake and egg weight. The addition of cerium oxide to the laying hens' feed improved feed conversion ratio and increased (p laying hens feed led to a significant (p laying hen diets. It was also observed that serum superoxide dismutase (SOD) activity and malondialdehyde (MDA) concentration decreased significantly with supplementation of cerium oxide in diets. Inclusion of cerium oxide resulted in a significant reduction in thiobarbituric acid reactive substance (TBARS) values in egg yolk in this study. It can be concluded that the addition of cerium oxide had positive effects on egg production, feed conversion ratio and egg shelf life. Based on the results of this study, it could be advised to supplement laying hens feed with cerium oxide as feed additives.

  17. Effect of cerium on structure modifications of a hybrid sol–gel coating, its mechanical properties and anti-corrosion behavior

    Energy Technology Data Exchange (ETDEWEB)

    Cambon, Jean-Baptiste, E-mail: cambon@chimie.ups-tlse.fr [Institut Carnot CIRIMAT, Université de Toulouse, UMR CNRS 5085, 118 Route de Narbonne, 31062 Toulouse Cedex 9 (France); Esteban, Julien; Ansart, Florence; Bonino, Jean-Pierre; Turq, Viviane [Institut Carnot CIRIMAT, Université de Toulouse, UMR CNRS 5085, 118 Route de Narbonne, 31062 Toulouse Cedex 9 (France); Santagneli, S.H.; Santilli, C.V.; Pulcinelli, S.H. [Departamento Fısico-Química, Instituto de Química, Universidade Estadual Paulista, UNESP, CP 355, 14801-970 Araraquara, SP (Brazil)

    2012-11-15

    Highlights: ► New sol–gel routes to replace chromates for corrosion protection of aluminum. ► Effect of cerium concentration on the microstructure of xerogel. ► Electrochemical and mechanical performances of hybrid coating with different cerium contents. ► Good correlation between the different results with an optimal cerium content of 0.01 M. -- Abstract: An organic–inorganic hybrid coating was developed to improve the corrosion resistance of the aluminum alloy AA 2024-T3. Organic and inorganic coatings derived from glycidoxypropyl-trimethoxysilane (GPTMS) and aluminum tri-sec-butoxide Al(O{sup s}Bu){sub 3}, with different cerium contents, were deposited onto aluminum by dip-coating process. Corrosion resistance and mechanical properties were investigated by electrochemical impedance measurements and nano-indentation respectively. An optimal cerium concentration of 0.01 M was evidenced. To correlate and explain the hybrid coating performances in relation to the cerium content, NMR experiments were performed. It has been shown that when the cerium concentration in the hybrid is higher than 0.01 M there are important modifications in the hybrid structure that account for the mechanical properties and anti-corrosion behavior of the sol–gel coating.

  18. Characterization of microstructure and catalytic of cerium oxide obtained by colloidal solution; Caracterizacao da microestrutura e da atividade catalitica de oxido de cerio obtido por solucao coloidal

    Energy Technology Data Exchange (ETDEWEB)

    Senisse, C.A.L.; Bergmann, C.P.; Alves, A.K., E-mail: carolinasenisse@hotmail.com [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alege, RS (Brazil). Lab. de Materiais Ceramicos

    2012-07-01

    This study investigated to obtain particles of cerium oxide, for use as catalysts for the combustion of methane using the technique of through polymeric colloidal solution. Obtaining the colloidal system is based on hydrolysis of salts such as cerium acetylacetonate, cerium nitrate in the presence of additives such as polyvinylbutyral (PVB), polyvinylpyrrolidone (PVP) and polyvinyl acetate (PVA), at concentrations of 5, 10 and 15% in aqueous or alcoholic medium. These solutions containing ions of interest were subjected to a heat treatment at 650° C for 30 minutes, with heating rate of 2 ° C/ min. After heat treatment, the fibers were characterized according to their morphology, surface area, crystallinity, weight loss and catalytic activity. Samples obtained from cerium acetylacetonate were more reactive than the cerium nitrate to the combustion of methane, as showed greater conversions and higher temperatures reached during the process, which is of utmost importance since the combustion catalytic methane is used for generating thermal energy. After the reaction with methane, the samples underwent significant change in surface area, probably due to the intensity of combustion reactions of the nitrate and the generation of heat involved in this reaction, which gave rise to coarse particles. During the combustion process using the obtained from particles of cerium acetylacetonate, there was the release of large quantities of nitrogen compared to the results of assays with the particles obtained with cerium nitrate. (author)

  19. Dynamic recrystallization behavior of commercial pure aluminum

    Institute of Scientific and Technical Information of China (English)

    LI Hui-zhong; ZHANG Xin-ming; CHEN Ming-an; LIU Zi-juan

    2006-01-01

    The flow stress feature and microstructure evolvement of a commercial pure aluminum were investigated by compression on Gleeble-1500 dynamic materials test machine. Optical microscopy (OM) and transmission electron microscopy (TEM) were applied to analyze the deformation microstructure of the commercial pure aluminum.The results show that the flow stress tends to be constant after a peak value and the dynamic recovery occurs when the deformation temperatures is 220 ℃ with the strain rate of 0.01 s-1; while the dynamic recrystallization occurs when the deformation temperature is higher than 380 ℃, and the flow stress exhibits a single peak at 460 ℃ with different strain rates from 0.001 s-1 to 1 s-1, and continuous dynamic recrystallization and geometric dynamic recrystallization occur during the hot compression of the commercial pure aluminum.

  20. Conclusive discrimination among N equidistant pure states

    Energy Technology Data Exchange (ETDEWEB)

    Roa, Luis; Hermann-Avigliano, Carla; Salazar, R. [Departamento de Fisica, Universidad de Concepcion, Barrio Universitario, Casilla 160-C, Concepcion (Chile); Klimov, A. B. [Departamento de Fisica, Universidad de Guadalajara, Revolucion 1500, 44420 Guadalajara, Jalisco (Mexico)

    2011-07-15

    We find the allowed complex overlaps for N equidistant pure quantum states. The accessible overlaps define a petal-shaped area on the Argand plane. Each point inside the petal represents a set of N linearly independent pure states and each point on its contour represents a set of N linearly dependent pure states. We find the optimal probabilities of success of discriminating unambiguously in which of the N equidistant states the system is. We show that the phase of the involved overlap plays an important role in the probability of success. For a fixed overlap modulus, the success probability is highest for the set of states with an overlap with phase equal to zero. In this case, if the process fails, then the information about the prepared state is lost. For states with a phase different from zero, the information could be obtained with an error-minimizing measurement protocol.

  1. Pure neuritic leprosy: Current status and relevance

    Directory of Open Access Journals (Sweden)

    P Narasimha Rao

    2016-01-01

    Full Text Available Pure neuritic leprosy has always been an enigma due to its clinical and management ambiguities. Although only the Indian Association of Leprologist's classification recognizes 'pure neuritic leprosy' as a distinct sub group of leprosy, cases nonetheless are reported from various countries of Asia, Africa, South America and Europe, indicating its global relevance. It is important to maintain pure neuritic leprosy as a subgroup as it constitutes a good percentage of leprosy cases reported from India, which contributes to more than half of global leprosy numbers. Unfortunately, a high proportion of these patients present with Grade 2 disability at the time of initial reporting itself due to the early nerve involvement. Although skin lesions are absent by definition, when skin biopsies were performed from the skin along the distribution of the affected nerve, a proportion of patients demonstrated leprosy pathology, revealing sub-clinical skin involvement. In addition on follow-up, skin lesions are noted to develop in up to 20% of pure neuritic leprosy cases, indicating its progression to manifest cutaneous disease. Over the decades, the confirmation of diagnosis of pure neuritic leprosy has been subjective, however, with the arrival and use of high-resolution ultrasonography (HRUS for nerve imaging, we have a tool not only to objectively measure and record the nerve thickening but also to assess the morphological alterations in the nerve including echo texture, fascicular pattern and vascularity. Management of pure neuritic leprosy requires multidrug therapy along with appropriate dose of systemic corticosteroids, for both acute and silent neuritis. Measures for pain relief, self-care of limbs and physiotherapy are important to prevent as well as manage disabilities in this group of patients.

  2. Pure neuritic leprosy: Current status and relevance.

    Science.gov (United States)

    Rao, P Narasimha; Suneetha, Sujai

    2016-01-01

    Pure neuritic leprosy has always been an enigma due to its clinical and management ambiguities. Although only the Indian Association of Leprologist's classification recognizes 'pure neuritic leprosy' as a distinct sub group of leprosy, cases nonetheless are reported from various countries of Asia, Africa, South America and Europe, indicating its global relevance. It is important to maintain pure neuritic leprosy as a subgroup as it constitutes a good percentage of leprosy cases reported from India, which contributes to more than half of global leprosy numbers. Unfortunately, a high proportion of these patients present with Grade 2 disability at the time of initial reporting itself due to the early nerve involvement. Although skin lesions are absent by definition, when skin biopsies were performed from the skin along the distribution of the affected nerve, a proportion of patients demonstrated leprosy pathology, revealing sub-clinical skin involvement. In addition on follow-up, skin lesions are noted to develop in up to 20% of pure neuritic leprosy cases, indicating its progression to manifest cutaneous disease. Over the decades, the confirmation of diagnosis of pure neuritic leprosy has been subjective, however, with the arrival and use of high-resolution ultrasonography (HRUS) for nerve imaging, we have a tool not only to objectively measure and record the nerve thickening but also to assess the morphological alterations in the nerve including echo texture, fascicular pattern and vascularity. Management of pure neuritic leprosy requires multidrug therapy along with appropriate dose of systemic corticosteroids, for both acute and silent neuritis. Measures for pain relief, self-care of limbs and physiotherapy are important to prevent as well as manage disabilities in this group of patients.

  3. Comparison of Diesel Engine Characteristic Using Pure Coconut Oil, Pure Palm Oil, and Pure Jatropha Oil as Fuel

    Directory of Open Access Journals (Sweden)

    Iman K. Reksowardojo

    2009-01-01

    Full Text Available Diesel engine can be operated on either pure plant oil (PPO oil or biodiesel. Biodiesel production process is expensive due to many stages of processes, while PPO has a lower cost of production, lower energy consumption, and simpler process. There are several potential biofuel resources in Indonesia such as coconut, palm, and jatropha. They are tropical plants with large amonts of their quantity. Experiment was conducted in 17 hours engine running test (endurance test with various operating cycle conditions. Test fuels are pure coconut oil (PCO, pure palm oil (PPaO, pure jatropha oil (PJO, and diesel fuel (DF as a datum. Each PPO blends with diesel fuel with composition 50%-volume. As a result, PCO has higher BSFC (10% before endurance test in comparison with diesel fuel, also PPaO (13% and PJO (27% show a similar condition. Surprisingly, all PPO have BSFC almost similar with DF after endurance test due to decreasing of engine components friction. On the other hand, PPO produces more uncompleted combustion than DF. Phosporus content has major responsibility of deposit growth. PCO, PPaO, and PJO result more engine deposits in comparison with DF, which accounts for 139,7%, 232,9%, and 288,9% respectively. Based on wear analysis, PCO has the best antiwear property among test fuels, whereas the worst is DF.

  4. Minimal covariant observables identifying all pure states

    Energy Technology Data Exchange (ETDEWEB)

    Carmeli, Claudio, E-mail: claudio.carmeli@gmail.com [D.I.M.E., Università di Genova, Via Cadorna 2, I-17100 Savona (Italy); I.N.F.N., Sezione di Genova, Via Dodecaneso 33, I-16146 Genova (Italy); Heinosaari, Teiko, E-mail: teiko.heinosaari@utu.fi [Turku Centre for Quantum Physics, Department of Physics and Astronomy, University of Turku (Finland); Toigo, Alessandro, E-mail: alessandro.toigo@polimi.it [Dipartimento di Matematica, Politecnico di Milano, Piazza Leonardo da Vinci 32, I-20133 Milano (Italy); I.N.F.N., Sezione di Milano, Via Celoria 16, I-20133 Milano (Italy)

    2013-09-02

    It has been recently shown by Heinosaari, Mazzarella and Wolf (2013) [1] that an observable that identifies all pure states of a d-dimensional quantum system has minimally 4d−4 outcomes or slightly less (the exact number depending on d). However, no simple construction of this type of minimal observable is known. We investigate covariant observables that identify all pure states and have minimal number of outcomes. It is shown that the existence of this kind of observables depends on the dimension of the Hilbert space.

  5. Reducing carbon dioxide to products

    Energy Technology Data Exchange (ETDEWEB)

    Cole, Emily Barton; Sivasankar, Narayanappa; Parajuli, Rishi; Keets, Kate A

    2014-09-30

    A method reducing carbon dioxide to one or more products may include steps (A) to (C). Step (A) may bubble said carbon dioxide into a solution of an electrolyte and a catalyst in a divided electrochemical cell. The divided electrochemical cell may include an anode in a first cell compartment and a cathode in a second cell compartment. The cathode may reduce said carbon dioxide into said products. Step (B) may adjust one or more of (a) a cathode material, (b) a surface morphology of said cathode, (c) said electrolyte, (d) a manner in which said carbon dioxide is bubbled, (e), a pH level of said solution, and (f) an electrical potential of said divided electrochemical cell, to vary at least one of (i) which of said products is produced and (ii) a faradaic yield of said products. Step (C) may separate said products from said solution.

  6. Aspects of carbon dioxide utilization

    Energy Technology Data Exchange (ETDEWEB)

    Omae, Iwao [Omae Research Laboratories, 335-23 Mizuno, Sayama, Saitama 350-1317 (Japan)

    2006-06-30

    Carbon dioxide reacts with hydrogen, alcohols, acetals, epoxides, amines, carbon-carbon unsaturated compounds, etc. in supercritical carbon dioxide or in other solvents in the presence of metal compounds as catalysts. The products of these reactions are formic acid, formic acid esters, formamides, methanol, dimethyl carbonate, alkylene carbonates, carbamic acid esters, lactones, carboxylic acids, polycarbonate (bisphenol-based engineering polymer), aliphatic polycarbonates, etc. Especially, the productions of formic acid, formic acid methyl ester and dimethylformamide with a ruthenium catalyst; dimethyl carbonate and urethanes with a dialkyltin catalyst; 2-pyrone with a nickel-phosphine catalyst; diphenyl carbonate with a lead phenoxide catalyst; the alternating copolymerization of carbon dioxide and epoxides with a zinc catalyst has attracted attentions as the industrial utilizations of carbon dioxide. The further development of these production processes is expected. (author)

  7. Carbon Dioxide Flux Measurement Systems

    Data.gov (United States)

    Oak Ridge National Laboratory — The Southern Great Plains (SGP) carbon dioxide flux (CO2 flux) measurement systems provide half-hour average fluxes of CO2, H2O (latent heat), and sensible heat. The...

  8. [XPS study on the influence of calcination conditions to cerium ion valence].

    Science.gov (United States)

    Mei, Yan; Yan, Jian-ping; Nie, Zuo-ren

    2010-01-01

    For the system of Ce(NO3)2.6H2O and urea solution during homogeneous precipitation method, X-ray diffraction (XRD), infrared spectrum (IR) and especially X-ray photoelectron spectroscopy (XPS) were used to study and characterize the product structure, variety of cerium ion valence, compound surface character and kernel electronic configurations. The results of XRD and IR showed that calcination temperature had a great effect on the cerium ion valence. The products are orthorhombic Ce2 O(CO3)2.H2O with valence III by using homogeneous precipitation method directly. When heated from the temperature 200 degrees C to 250 degrees C, the product of CeO(CO3)2.H2O with valence VI was finally changed into stable CeO2 with valence IV. XPS was used to study the surface character and kernel electronic configurations of the three different compounds through fine scanning of O(1s), Ce(3d) and Ce(4d) apices, and the results approved that the compounds with different valences are caused by the different valence electronic configurations of the products.

  9. Custom cerium oxide nanoparticles protect against a free radical mediated autoimmune degenerative disease in the brain.

    Science.gov (United States)

    Heckman, Karin L; DeCoteau, William; Estevez, Ana; Reed, Kenneth J; Costanzo, Wendi; Sanford, David; Leiter, James C; Clauss, Jennifer; Knapp, Kylie; Gomez, Carlos; Mullen, Patrick; Rathbun, Elle; Prime, Kelly; Marini, Jessica; Patchefsky, Jamie; Patchefsky, Arthur S; Hailstone, Richard K; Erlichman, Joseph S

    2013-12-23

    Cerium oxide nanoparticles are potent antioxidants, based on their ability to either donate or receive electrons as they alternate between the +3 and +4 valence states. The dual oxidation state of ceria has made it an ideal catalyst in industrial applications, and more recently, nanoceria's efficacy in neutralizing biologically generated free radicals has been explored in biological applications. Here, we report the in vivo characteristics of custom-synthesized cerium oxide nanoparticles (CeNPs) in an animal model of immunological and free-radical mediated oxidative injury leading to neurodegenerative disease. The CeNPs are 2.9 nm in diameter, monodispersed and have a -23.5 mV zeta potential when stabilized with citrate/EDTA. This stabilizer coating resists being 'washed' off in physiological salt solutions, and the CeNPs remain monodispersed for long durations in high ionic strength saline. The plasma half-life of the CeNPs is ∼4.0 h, far longer than previously described, stabilized ceria nanoparticles. When administered intravenously to mice, the CeNPs were well tolerated and taken up by the liver and spleen much less than previous nanoceria formulations. The CeNPs were also able to penetrate the brain, reduce reactive oxygen species levels, and alleviate clinical symptoms and motor deficits in mice with a murine model of multiple sclerosis. Thus, CeNPs may be useful in mitigating tissue damage arising from free radical accumulation in biological systems.

  10. Studies on luminescence from a cerium-doped strontium stannate phosphor.

    Science.gov (United States)

    Karabulut, Yüksel; Ayvacikli, Mehmet; Canimoglu, Adil; Garcia Guinea, Javier; Can, Nurdogan

    2015-06-01

    The crystal structure and morphology of Ce(3+) -doped SrSnO3 materials prepared using the solid-state reaction method were extensively characterized using experimental techniques. X-Ray diffraction results show that the cerium substitution of strontium does not change the structure of the strontium stannate. Raman spectroscopy was used to investigate the microstructures and lattice vibrations. Environmental scanning electron microscopy images showed that phosphors aggregate and their particles form irregular shapes. SrSnO3 exhibits an intense green emission with a broad band originating from the 5d(1)  → 4f(1) transition of cerium. It was observed that, after exposure to beta-irradiation, the glow curve of this material has two broad thermoluminescence peaks, one centered at ~ 127°C and the other at ~ 245°C for a heating rate of 5 K/s. The kinetic parameters, which include the frequency factor and the activation energy of the material, were calculated using Chen's method, after beta-irradiation. The fading and reusability of the phosphor were also studied and it was found that the phosphor is suitable for radiation dosimetry. Copyright © 2014 John Wiley & Sons, Ltd.

  11. Self-healing Performance of Composite Coatings Prepared by Phosphating and Cerium Nitrate Post-sealing

    Institute of Scientific and Technical Information of China (English)

    LIN Bilan; LU Jintang

    2015-01-01

    The phosphated and cerium nitrate post-sealed galvanized steel was ifrstly scratched to expose zinc layer and then placed in neutral salt spray (NSS) chamber for different durations. The microstructure and compositions of the scratches were investigated using SEM and EDS. The phases of the corrosion products were examined through XRD. The self-healing mechanism of the composite coatings was discussed. The experimental results show that the composite coatings have an excellent corrosion resistance. The corrosion products increase with corrosion time and ifnally cover the whole scratch. They contain phosphorous, cerium, oxygen, chloride and zinc, and are ifne needle and exceedingly compact. The composite coatings are favorable self-healing. During corrosion, the self-healing ions such as Ce3+, Ce4+, PO43-, Zn2+ in the composite coatings were dissolved, migrated, recombined, and covered the exposed zinc, impeding zinc corrosion. The self-healing process of the scratches on the composite coatings can be divided into three stages, about 2 h, 4 h, and 24 h, respectively.

  12. Honeycomb nano cerium oxide fabricated by vacuum drying process with sodium alginate

    Science.gov (United States)

    Zhao, Guozheng; Li, Changbo; Zhang, Honglin

    2017-06-01

    Nano cerium oxide (CeO2) with honeycomb structure were synthesized simply and rapidly by vacuum drying method with sodium alginate as the biological template agent, Ce(NO3)3·6H2O as cerium source. The composition, aperture size, specific surface area and morphology of the prepared samples were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), N2 adsorption-desorption and scanning electron microscopy (SEM). Simultaneously, the effects on the morphology of the samples, which were caused by the drying method and the concentration of sodium alginate, were investigated. The results indicate that the prepared samples were nano CeO2 with high crystallinity and uniform dispersion, most of which had mesoporous, macroporous and honeycomb structure. The specific surface area of CeO2 is 210.0 m2/g, and the average aperture is 12.77 nm. The prepared samples can act as catalyst in the catalytic wet oxidation process for the treatment of high concentration organic wastewater, and the COD removal rate could exceed 90%.

  13. Selective catalytic oxidation of ammonia over copper-cerium composite catalyst.

    Science.gov (United States)

    Lou, Jie-Chung; Hung, Chang-Mao; Yang, Sheng-Fu

    2004-01-01

    This work considers the oxidation of ammonia (NH3) by selective catalytic oxidation (SCO) over a copper (Cu)-cerium (Ce) composite catalyst at temperatures between 150 and 400 degrees C. A Cu-Ce composite catalyst was prepared by coprecipitation of copper nitrate and cerium nitrate at various molar concentrations. This study also considers how the concentration of influent NH3 (500-1000 ppm), the space velocity (72,000-110,000 hr(-1)), the relative humidity (12-18%) and the concentration of oxygen (4-20%) affect the operational stability and the capacity for removing NH3. The effects of the O2 and NH3 content of the carrier gas on the catalyst's reaction rate also are considered. The experimental results show that the extent of conversion of NH3 by SCO in the presence of the Cu-Ce composite catalyst was a function of the molar ratio. The NH3 was removed by oxidation in the absence of Cu-Ce composite catalyst, and approximately 99.2% NH3 reduction was achieved during catalytic oxidation over the Cu-Ce (6:4, molar/molar) catalyst at 400 degrees C with an O2 content of 4%. Moreover, the effect of the initial concentration and reaction temperature on the removal of NH3 in the gaseous phase was also monitored at a gas hourly space velocity of less than 92,000 hr(-1).

  14. Visible Light Induced Photocatalysis of Cerium Ion Modified Titania Sol and Nanocrystallites

    Institute of Scientific and Technical Information of China (English)

    Yibing XIE; Chunwei YUAN

    2004-01-01

    The cerium ion(Ce4+) doped titania sol and nanocrystallites were prepared by chemical coprecipitation-peptization and hydrothermal synthesis methods, respectively. The X-ray diffraction pattern shows that Ce4+-TiO2 xerogel powder has semicrystalline structure and thermal sintering sample has crystalline structure. Ce4+-TiO2 nanocrystallites are composed of the major anatase phase titania (88.82 wt pct) and a small amount of crystalline cerium titanate.AFM micrograph shows that primary particle size of well-dispersed ultrafine sol particles is below 15 nm in diameter.The particle sizes are 30 nm for xerogel sample and 70 nm for nanocrystallites sample, which is different from the estimated values (2.41 nm and 4.53 nm) by XRD Scherrer's formula. The difference is mainly due to aggregation of nanocrystallites. The experimental results exhibit that photocatalysts of Ce4+-TiO2 sol and nanocrystallites have the ability to photodegrade reactive brilliant red dye (X-3B) under visible light irradiation with the ion-TiO2/VIS/dye system. Moreover, Ce4+ doped titania sol has shown higher efficiency than the nanocrystallites sample in respect of potocatalytic activity. Meanwhile, dye photodegradation mechanisms are proposed to different photocatalytic reaction systems, which are dye photosensitization, ion-dye photosensitization and interband photocatalysis & dye photosensitization with respect to TiO2 nanocrystallites, Ce4+-TiO2 sol and Ce4+-TiO2 nanocrystallites system.

  15. Cerium relieving the inhibition of photosynthesis and growth of spinach caused by lead

    Institute of Scientific and Technical Information of China (English)

    ZHOU; Min

    2009-01-01

    Chloroplasts were isolated from spinach cultured in lead chloride-present, Ce3+-administered, cerium chloride-administered lead chloride-present Hoagland's media or that of Hoagland's media. The experimental study demonstrated the effects of cerium (Ce) on distribu-tion of light energy and photochemical activities of spinach chloroplast grown in lead (Pb)-present media. It was observed that Pb2+ signifi-cantly inhibited photosynthesis in spinach, including light absorption, energy transfer from LHCII to photosystem II, excitation energy dis-tribution from photosystem I to photosystem II, and transformation from light energy to electron energy and oxygen evolution of chloroplasts,and decreased spinach growth. However, Ce3+ treatment to pb2+-present chloroplasts could obviously improve light absorption and excitation energy distribution in both photosystems and increase activity of photochemical reaction and oxygen evolution of chloroplasts. The results suggested that Ce3+ under Pb2+ stress could maintain the stability of chloroplast membrane, and improve photosynthesis of spinach chloro-plast, thus promote spinach growth.

  16. Cerium relieving the inhibition of photosynthesis and growth of spinach caused by lead

    Institute of Scientific and Technical Information of China (English)

    ZHOU Min; ZE Yuguan; LI Na; DUAN Yanmei; CHEN Ting; LIU Chao; HONG Fashui

    2009-01-01

    Chloroplasts were isolated from spinach cultured in lead chloride-present, Ce~(3+)-administered, cerium chloride-administered lead chloride-present Hoagland's media or that of Hoagland's media. The experimental study demonstrated the effects of cerium (Ce) on distribu-tion of light energy and photochemical activities of spinach chloroplast grown in lead (Pb)-present media. It was observed that Pb~(2+) signifi-cantly inhibited photosynthesis in spinach, including light absorption, energy transfer from LHCII to photosystem II, excitation energy dis-tribution from photosystem I to photosystem II, and transformation from light energy to electron energy and oxygen evolution of chloroplasts,and decreased spinach growth. However, Ce~(3+) treatment to pb~(2+)-present chloroplasts could obviously improve light absorption and excitation energy distribution in both photosystems and increase activity of photochemical reaction and oxygen evolution of chloroplasts. The results suggested that Ce~(3+) under Pb~(2+) stress could maintain the stability of chloroplast membrane, and improve photosynthesis of spinach chloro-plast, thus promote spinach growth.

  17. Removal of aromatic amines from water by montmorillonite-(cerium or zirconium) phosphate crosslinked compounds

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Pradas, E.; Villafranca-Sanchez, M.; Urena-Amate, M.D. (Univ. of Almeria (Spain). Dept. of Inorganic Chemistry); Del Rey-Bueno, F.; Garcia-Rodriguez, A. (Univ. of Granada (Spain). Dept. of Inorganic Chemistry)

    To evaluate the potential use of two montmorillonite-(Ce or Zr) phosphate crosslinked compounds in removing organic pollutants such as aniline, p-toluidine, and p-acetylaniline from water, adsorption experiments were performed under conditions of varied temperature (288 and 308 K). Adsorption on the montmorillonite-Ce-phosphate compound was best described by a hyperbolic (H-type) isotherm, whereas for the montmorillonite-Zr-phosphate compound, S-type isotherms were obtained for p-toluidine and aniline and L-type for p-acetylaniline. Amines adsorption increases with increasing temperature on the cerium crosslinked material, while for the zirconium-crosslinked compound, adsorption decreases as temperature increases from 288 to 308 K, possibly due to a mainly physical process. Fourier-transform infrared (FTIR) spectroscopy indicated that at the pH generated by the adsorbents, the protonated species of these amines plays an important role in the adsorption process. X-ray diffraction analysis showed that the aromatic amines are intercalated into the adsorbents. For any given amine, the cerium-montmorillonite adsorbent shows a higher capacity of adsorption compared with zirconium-montmorillonite adsorbent, so it might be reasonably used in removing aromatic amines from water.

  18. Cerium(III) molybdate nanoparticles: Synthesis, characterization and radionuclides adsorption studies.

    Science.gov (United States)

    Yousefi, Taher; Khanchi, Ali Reza; Ahmadi, Seyed Javad; Rofouei, Mohamad Kazem; Yavari, Ramin; Davarkhah, Reza; Myanji, Behzad

    2012-05-15

    Cerium(III) molybdate nanostructure with average size about 40nm was prepared by adding cerium(III) chloride and ammonium molybdate solutions under varying conditions. The product was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR), thermogravimetric analysis (TGA) and Brunauere Emmette Teller (BET) techniques. Ion exchange capacity of the sample for potassium ion and distribution coefficients (K(d)) for 23 metal ions were determined, the K(d) values for Tl(I), Pb(II), Th(IV), U(VI), and Cs(I) ions were found to be sufficiently high for their removal from various effluents. The adsorption behavior of the sample towards Cs(I)(134) species were studied. Finally, the binary separation of Dy(III)-U(VI), Sm(III)-Th(IV) and Cs(I)-Rb(I) and removal of Cs(I)(134) from the real sample were successfully achieved.

  19. Cerium oxide for the destruction of chemical warfare agents: A comparison of synthetic routes

    Energy Technology Data Exchange (ETDEWEB)

    Janoš, Pavel, E-mail: pavel.janos@ujep.cz [Faculty of the Environment, University of Jan Evangelista Purkyně, Králova Výšina 7, 400 96 Ústí nad Labem (Czech Republic); Henych, Jiří [Faculty of the Environment, University of Jan Evangelista Purkyně, Králova Výšina 7, 400 96 Ústí nad Labem (Czech Republic); Institute of Inorganic Chemistry AS CR v.v.i., 25068 Řež (Czech Republic); Pelant, Ondřej; Pilařová, Věra; Vrtoch, Luboš [Faculty of the Environment, University of Jan Evangelista Purkyně, Králova Výšina 7, 400 96 Ústí nad Labem (Czech Republic); Kormunda, Martin [Faculty of Sciences, University of Jan Evangelista Purkyně, České Mládeže 8, 400 96 Ústí nad Labem (Czech Republic); Mazanec, Karel [Military Research Institute, Veslařská 230, 637 00 Brno (Czech Republic); and others

    2016-03-05

    Highlights: • Four synthetic routes were compared to prepare the nanoceria-based reactive sorbents. • The sorbents prepared by homogeneous hydrolysis destroy efficiently the soman and VX nerve agents. • Toxic organophosphates are converted to less-dangerous products completely within a few minutes. • Surface non-stoichiometry and −OH groups promote the destruction by the S{sub N}2 mechanism. - Abstract: Four different synthetic routes were used to prepare active forms of cerium oxide that are capable of destroying toxic organophosphates: a sol–gel process (via a citrate precursor), homogeneous hydrolysis and a precipitation/calcination procedure (via carbonate and oxalate precursors). The samples prepared via homogeneous hydrolysis with urea and the samples prepared via precipitation with ammonium bicarbonate (with subsequent calcination at 500 °C in both cases) exhibited the highest degradation efficiencies towards the extremely dangerous nerve agents soman (O-pinacolyl methylphosphonofluoridate) and VX (O-ethyl S-[2-(diisopropylamino)ethyl] methylphosphonothioate) and the organophosphate pesticide parathion methyl. These samples were able to destroy more than 90% of the toxic compounds in less than 10 min. The high degradation efficiency of cerium oxide is related to its complex surface chemistry (presence of surface −OH groups and surface non-stoichiometry) and to its nanocrystalline nature, which promotes the formation of crystal defects on which the decomposition of organophosphates proceeds through a nucleophilic substitution mechanism that is not dissimilar to the mechanism of enzymatic hydrolysis of organic phosphates by phosphotriesterase.

  20. Effects of different valences of cerium ion on conformation of Horseradish Peroxidase

    Institute of Scientific and Technical Information of China (English)

    XIANG Li; GE Zhiqiang

    2008-01-01

    Our previous studies demonstrated that Ce4+ could induce reactive oxygen species (ROS) burst as a signal to promote pacilitaxel biosynthesis in suspension cultured Taxus cuspidate cells. To further understand the mechanism of cerium ions inducing ROS burst, circular dichroism (CD), synchronous fluorescence, and electron paramagnetic resonance (EPR) were used to detect them inducing conforma-tional change of horseradish peroxidase (HRF). Horseradish peroxidase activity was reduced by 78% by 0.1 mmol/L Ce4+, whereas it was only reduced by 28% by 0.1 mmol/L Ce3+. Circular dichroism spectra showed that the percentage of transition from helical content and other structure to βstrands andβturns was 23.1 when induced by Ce4+, whereas it was only 13.2 when induced by Ce3+. In synchronous fluorescence spectra, Ce4+ led to red shift and intensity-elevation of tryptophan fluorescence emission maximum, whereas in the case of Ce3+, the results were a contrast to the above. Furthermore, g factor (gx and gy) in electron paramagnetic resonance (EPR) induced by Ce4+ and Ce3+ was significantly different. These results indicated that the different valence of cerium ion induced various conformations of HRP, and Ce4+ was more effective than Ce3+. This suggested that Ce4+ affected the burst of ROS through changing the conformation of oxidoreductase.

  1. FT-IR Studies of Cerium Oxide Nanoparticles and Natural Zeolite Materials

    Directory of Open Access Journals (Sweden)

    Oana Lelia Pop

    2015-05-01

    Full Text Available An emerging topic of our days is nanoscience and nanotechnology successfully applied in the food industry. Characteristics such as size, surface area and morphology can modify the basic properties and the chemical reactivity of the nanomaterials. The breakthrough of innovative materials, processes, and phenomena at the nanoscale, as well as the progress of new experimental and theoretical techniques for research, supply novel opportunities for the expansion of original nanosystems and nanostructured materials. These study examine two types of nanoparticles, namely cerium oxide nanoparticles (CeO2 NP and natural zeolites. In view of the importance of CeO2 NP in various biological applications, the primary objective of this study is to characterise four samples of CeO2 NP in order to understand the role of the synthesis process in the final product. Nanocrystalline natural zeolites are materials with interesting properties which allows them to be used as adjuvant in many therapies. The characterisation of CeO2 NP and two types of natural zeolites using Fourier Transform Infrared (FT-IR spectroscopy is described. Therefore, this study examined two types of nanomaterials, namely cerium oxide nanoparticles and zeolites, for further applications on microorganisms and living cells.

  2. Kinetics of Cerium(IV) Extraction from H(2)SO(4)-HF Medium with Cyanex 923.

    Science.gov (United States)

    Liao, Wuping; Yu, Guihong; Yue, Shantang; Li, Deqian

    2002-03-11

    Studies of the extraction kinetics of cerium(IV) from H(2)SO(4)-HF solutions with Cyanex 923 in n-heptane have been carried out using a constant interfacial area cell with laminar flow. The experimental hydrodynamic conditions were chosen so that the contribution of diffusion to the measured rate of reaction was minimized. The data were analyzed in terms of pseudo-first order constants. The results were compared with those of the system without HF. It was concluded that the addition of HF reduces the activation energy for the forward rate from 46.2 to 36.5 kJ mol(-1) while it has an opposite effect on the activation energy for the reverse process(the activation energy increased from 23.3 to 90.8 kJ mol(-1)). Thus, HF can accelerate the rate of cerium(IV) extraction. At the same time, the extraction rate is controlled by a mixed chemical reaction-diffusion rather than by a chemical reaction alone. A rate equation has also been obtained.

  3. Cerium and neodymium co-precipitation in molten chloride by wet argon sparging

    Energy Technology Data Exchange (ETDEWEB)

    Vigier, J.F. [CEA, Nuclear Energy Division, RadioChemistry and Processes Department, SMCS/LEPS, F-30207 Bagnols sur Ceze (France); Unite de Catalyse et de Chimie du Solide, UCCS UMR CNRS 8181, Univ. Lille Nord de France, ENSCL-USTL, B.P. 90108, 59652 Villeneuve d' Ascq Cedex (France); Renard, C., E-mail: catherine.renard@ensc-lille.fr [Unite de Catalyse et de Chimie du Solide, UCCS UMR CNRS 8181, Univ. Lille Nord de France, ENSCL-USTL, B.P. 90108, 59652 Villeneuve d' Ascq Cedex (France); Laplace, A. [CEA, Nuclear Energy Division, RadioChemistry and Processes Department, SMCS/LEPS, F-30207 Bagnols sur Ceze (France); Lacquement, J. [CEA, Nuclear Energy Division, DTEC/DIR, F-30207 Bagnols sur Ceze (France); Abraham, F. [Unite de Catalyse et de Chimie du Solide, UCCS UMR CNRS 8181, Univ. Lille Nord de France, ENSCL-USTL, B.P. 90108, 59652 Villeneuve d' Ascq Cedex (France)

    2013-01-15

    Co-precipitations of cerium (III) and neodymium (III) at 10 wt.% in LiCl-CaCl{sub 2} (30-70 mol%) molten salt at 705 Degree-Sign C have been achieved using an original way of precipitation, wet argon sparging. Several CeCl{sub 3}/NdCl{sub 3} ratios have been studied, and the isolated powders were analyzed using different characterization methods including XRD investigations. The lanthanides precipitation yields have been determined around 99.9% using ICP-AES analysis. XRD demonstrated that the precipitates mainly contained mixed oxychloride (Ce{sub 1-x}Nd{sub x})OCl and a small amount of the mixed oxide Ce{sub 1-y}Nd{sub y}O{sub 2-0.5y}. Calcination of these precipitates has resulted in the cerium and neodymium mixed oxides. For the precipitation with a Ce/Nd = 50/50 ratio, an hydroxychloride Ln(OH){sub 2}Cl and the oxychloride Ce{sup IV}(Nd{sub 0.7}Ce{sub 0.3}){sup III}O{sub 3}Cl have been identified as unexpected intermediate compounds.

  4. Production of cerium-apatite in sound and carious dental enamel under in vitro conditions.

    Science.gov (United States)

    Kiss, J; Bánóczy, J; Fehérváry, E; Gintner, Z; Albrecht, M

    1990-01-01

    Incipient dental caries--according to up-to-date concepts in dental research--means a demineralization without cavity formation. At this stage the carious process is reversible, and remineralization can be achieved in the presence of locally applied fluorides. In chrystalchemical experiments, however, by treating natural apatites with lanthanides, [Ce, La, Pr, Nd, Sm, Eu, Tb ... Y, Sc] a more resistant complex could be developed. In this study extracted human molar teeth were kept for 60 days in Cerium (III)-nitrate solution, in order to investigate the incorporation of Ce3+ into human sound and carious enamel by light-microscopic-, and electron microprobe methods. Ce3+ was incorporated in sound enamel as well as into the incipient carious lesion, showing the histological characteristics of a remineralizing lesion. The mean values of the microprobe analysis data showed an increase in Ce3+ changing place with the Ca2+ the developing cerium-apatite being more hard and resistant from a mineralophysical point of view.

  5. Catalytic wet peroxidation of pyridine bearing wastewater by cerium supported SBA-15.

    Science.gov (United States)

    Subbaramaiah, V; Srivastava, Vimal Chandra; Mall, Indra Deo

    2013-03-15

    Cerium supported SBA-15 (Ce/SBA-15) was synthesized by two-step synthesis method in acidic medium. It was further characterized by various characterization techniques such as X-ray diffraction, field-emission scanning electron microscopy, Fourier transform infrared spectroscopy and N2 adsorption-desorption pore size distribution analysis. The Ce/SBA-15 showed highly ordered meso-structure with pore diameter≈70-100Ǻ and pore volume≈0.025cm(3)/g. Ce/SBA-15 was further evaluated as a catalyst for the oxidation of highly toxic and non-biodegradable material, pyridine, by catalytic wet-peroxidation method. The effects of various operating parameters such as catalyst dose (0.5-6g/l), stoichiometric ratio of H2O2/pyridine (1-6), initial pyridine concentration (50-800mg/l) and temperature (313-358K) have been evaluated and optimized. Ce/SBA-15 showed stable performance during reuse for six cycles with negligible cerium leaching. Kinetic and thermodynamic parameters and operation cost have also been determined.

  6. Cerium-zinc redox flow battery: Positive half-cell electrolyte studies

    Institute of Scientific and Technical Information of China (English)

    XIE Zhipeng; ZHOU Debi; XIONG Fengjiao; ZHANG Shimin; HUANG Kelong

    2011-01-01

    Experimental work was performed to evaluate the Ce3+/Ce4+ redox couple in methane sulfonic acid (MSA) electrolyte for use in redox flow battery (RFB) technology. The electrochemical behaviour of the Ce3+/Ce4+ in MSA media was investigated using cyclic voltammetry, linear sweep voltammetry, chronoamperometry and rotating disc electrode. The standard rate constant of the Ce3+/Ce4+ redox reaction on graphite electrode in MSA was 4.06x10-4 cm/s. The diffusion coefficient of Ce3+ in MSA was 5.87-6.15x10-6 cm2/s, and was 2.56-2.68x 10-6 cm2/s for Ce4+. The energy efficiency of a cerium-zinc test cell was 74.8%. The high stability of cerium salts in MSA media and relatively fast redox kinetics of the Ce3+/Ce4+ redox reaction at graphite ectrode indicated that the Ce3+/Ce4+ might be well suited for use in RFB technology.

  7. Recuperative supercritical carbon dioxide cycle

    Science.gov (United States)

    Sonwane, Chandrashekhar; Sprouse, Kenneth M; Subbaraman, Ganesan; O'Connor, George M; Johnson, Gregory A

    2014-11-18

    A power plant includes a closed loop, supercritical carbon dioxide system (CLS-CO.sub.2 system). The CLS-CO.sub.2 system includes a turbine-generator and a high temperature recuperator (HTR) that is arranged to receive expanded carbon dioxide from the turbine-generator. The HTR includes a plurality of heat exchangers that define respective heat exchange areas. At least two of the heat exchangers have different heat exchange areas.

  8. [The influences of lanthanum,cerium and fluoride on the activity of glucosyltransferase(GTF) and adherence of oral cariogenic bacteria in vitro

    Science.gov (United States)

    Li, M Y; Zhang, W G; Liu, Z

    1998-09-01

    OBJECTIVE:Study of the influences of lanthanum,cerium and fluoride on the activity of flucosyltransferase(GTF) and adherence of oral cariogenic bacteria. METHODS: The influences of lanthanum,certium and fluoride on the acitivity of GTF and adherences of Steptococcus sobrinus 6715,Lactobacillus 4356 and Actinomycetes viscosus 19246 in vitro were investigated. RESULTS: Lanthanum and cerium can efficiently inhibit the acitivity of GTF than fluoride. CONCLUSION: The result was given a data that lanthanum and cerium could be used as a cariostatic agent in future.At the same time the inhibition of the bacterial adherence by these trace elements was also revealed.

  9. Effect of cerium ion implantation on the oxidation behavior of zircaloy-4 at 500 degree sign C

    CERN Document Server

    Chen, X W; Yu, H R; Zhou, Q G; Chen, B S

    2002-01-01

    In order to investigate the oxidation behavior changes of zircaloy-4 induced by cerium ion implantation using a MEVVA source at an energy of 40 keV with a dose range from 1x10 sup 1 sup 6 to 1x10 sup 1 sup 7 ions/cm sup 2 at the maximum temperature of 130 degree sign C, weight gain curves of the different specimens including as-received zircaloy-4 and cerium-implanted zircaloy-4 were measured after oxidation in air at 500 degree sign C for 100 min. It was obviously found that a significant improvement was achieved in the oxidation behavior of cerium ion implanted zircaloy-4 compared with that of the as-received zircaloy-4. The depth profile of the element composition in the surface region of the samples was obtained by Auger electron spectroscopy, and the valence of the oxides in the scale was analyzed by X-ray photoemission spectroscopy. Glancing angle X-ray diffraction employed to examine the phase transformation in the oxide films showed that the addition of cerium transformed the phase from monoclinic zir...

  10. Comparative hazard identification of nano- and micro-sized cerium oxide particles based on 28-day inhalation studies in rats

    NARCIS (Netherlands)

    Gosens, Ilse; Mathijssen, Liesbeth E A M; Bokkers, Bas G H|info:eu-repo/dai/nl/304847062; Muijser, Hans; Cassee, Flemming R.|info:eu-repo/dai/nl/143038990

    2014-01-01

    There are many uncertainties regarding the hazard of nanosized particles compared to the bulk material of the parent chemical. Here, the authors assess the comparative hazard of two nanoscale (NM-211 and NM-212) and one microscale (NM-213) cerium oxide materials in 28-day inhalation toxicity studies

  11. Influence of hydroxyl content of binders on rheological properties of cerium-gadolinium oxide (CGO) screen printing inks

    DEFF Research Database (Denmark)

    Marani, Debora; Gadea, Christophe; Hjelm, Johan;

    2015-01-01

    vinyl resins) were selected and characterized in solution via viscosimetry method. A high degree of hyper-entanglement was observed for ethyl cellulose polymers, whereas a mitigated effect characterized the two vinyl resins. Cerium-gadolinium oxides (CGO)-based inks, prepared using the selected binders...

  12. Effect of rare element cerium on the morphology and corrosion resistance of electro-less Ni-P coatings

    Directory of Open Access Journals (Sweden)

    Fu Chuan-qi

    2015-01-01

    Full Text Available This paper reports an experimental study on the microstructure and corrosion resistance of electro-less Ni-P coatings with increasing content of the rare element cerium (Ce. Surface morphology and the composition of the electro-less Ni-P coatings were studied by scanning electron microscope (SEM, X-ray energy dispersed analysis (EDS and X-ray diffraction analysis (XRD. Hardness and Adhesive force are researched by a HX-200 Vickers diamond indenter micro-hardness tester. Furthermore, we study the adhesive force by using the Revetest scratch tester. We get the possession of Ce amorphous Ni-P coatings which has excellent properties in anti-corrosion. The effect of the rare element cerium concentration on corrosion resistance of the coatings was evaluated in the groundwater immersion test and porosity test, respectively. The results indicated that added little the rare element cerium into the plating bath increased the phosphorus content of the coatings, decreased the corrosion rates, it also decreases the porosity of the amorphous Ni-P coatings. The lowest corrosion rates of the amorphous Ni-P coatings in groundwater immersion test is 4.1 um · h-1, at the rare element cerium concentration of 0.12g · L-1.

  13. A mixed acid based vanadium-cerium redox flow battery with a zero-gap serpentine architecture

    Science.gov (United States)

    Leung, P. K.; Mohamed, M. R.; Shah, A. A.; Xu, Q.; Conde-Duran, M. B.

    2015-01-01

    This paper presents the performance of a vanadium-cerium redox flow battery using conventional and zero-gap serpentine architectures. Mixed-acid solutions based on methanesulfonate-sulfate anions (molar ratio 3:1) are used to enhance the solubilities of the vanadium (>2.0 mol dm-3) and cerium species (>0.8 mol dm-3), thus achieving an energy density (c.a. 28 Wh dm-3) comparable to that of conventional all-vanadium redox flow batteries (20-30 Wh dm-3). Electrochemical studies, including cyclic voltammetry and galvanostatic cycling, show that both vanadium and cerium active species are suitable for energy storage applications in these electrolytes. To take advantage of the high open-circuit voltage (1.78 V), improved mass transport and reduced internal resistance are facilitated by the use of zero-gap flow field architecture, which yields a power density output of the battery of up to 370 mW cm-2 at a state-of-charge of 50%. In a charge-discharge cycle at 200 mA cm-2, the vanadium-cerium redox flow battery with the zero-gap architecture is observed to discharge at a cell voltage of c.a. 1.35 V with a coulombic efficiency of up to 78%.

  14. The properties of protective oxide scales containing cerium on alloy 800H in oxidizing and oxidizing/sulphidizing environments

    NARCIS (Netherlands)

    Haanappel, V.A.C.; Fransen, T.; Geerdink, B.; Gellings, P.J.; Stroosnijder, M.F.

    1991-01-01

    The corrosion protection of oxide scales formed by electrophoretic deposition in a cerium-containing sol on Alloy 800H, a 32Ni-20Cr steel, followed by firing in air at 1123 K was studied in oxidizing and mixed oxidizing/sulphidizing environments at elevated temperatures. In particular, the influence

  15. Pure word deafness and pure anarthria in a patient with frontotemporal dementia.

    Science.gov (United States)

    Iizuka, O; Suzuki, K; Endo, K; Fujii, T; Mori, E

    2007-04-01

    A 66-year-old right-handed man developed pure anarthria following pure word deafness. In addition to language disorders, his behavior gradually changed and finally included violence against his wife. Brain magnetic resonance imagings revealed atrophy of the left perisylvian area, which included the inferior half of the precentral gyrus and the upper portion of the superior temporal gyrus, consistent with frontotemporal dementia (FTD). It has been documented as either a disorder of expressive language or as an impaired understanding of word meaning. Unlike with pure anarthria, pure word deafness is not included in the clinical diagnostic current criteria for FTD. However, a large variety of language symptoms can appear in FTD according to the distribution of pathological changes in the frontotemporal cortices. This case suggests that pure word deafness could be a prodomal symptom of FTD.

  16. Are all maximally entangled states pure?

    CERN Document Server

    Cavalcanti, D; Terra-Cunha, M O

    2005-01-01

    In this Letter we study if all maximally entangled states are pure through several entanglement monotones. Our conclusions allow us to generalize the idea of monogamy of entanglement. Then we propose a polygamy of entanglement, which express that if a general multipartite state is maximally entangled it is necessarily factorized by any other system.

  17. Implicit Reading in Chinese Pure Alexia

    Science.gov (United States)

    Shan, Chunlei; Zhu, Renjing; Xu, Mingwei; Luo, Benyan; Weng, Xuchu

    2010-01-01

    A number of recent studies have shown that some patients with pure alexia display evidence of implicit access to lexical and semantic information about words that they cannot read explicitly. This phenomenon has not been investigated systematically in Chinese patients. We report here a case study of a Chinese patient who met the criteria for pure…

  18. Pure science and the problem of progress.

    Science.gov (United States)

    Douglas, Heather

    2014-06-01

    How should we understand scientific progress? Kuhn famously discussed science as its own internally driven venture, structured by paradigms. He also famously had a problem describing progress in science, as problem-solving ability failed to provide a clear rubric across paradigm change--paradigm changes tossed out problems as well as solving them. I argue here that much of Kuhn's inability to articulate a clear view of scientific progress stems from his focus on pure science and a neglect of applied science. I trace the history of the distinction between pure and applied science, showing how the distinction came about, the rhetorical uses to which the distinction has been put, and how pure science came to be both more valued by scientists and philosophers. I argue that the distinction between pure and applied science does not stand up to philosophical scrutiny, and that once we relinquish it, we can provide Kuhn with a clear sense of scientific progress. It is not one, though, that will ultimately prove acceptable. For that, societal evaluations of scientific work are needed.

  19. Binomial Squares in Pure Cubic Number Fields

    CERN Document Server

    Lemmermeyer, Franz

    2011-01-01

    Let K = Q(\\omega) with \\omega^3 = m be a pure cubic number field. We show that the elements\\alpha \\in K^\\times whose squares have the form a - \\omega form a group isomorphic to the group of rational points on the elliptic curve E_m: y^2= x^3 - m.

  20. Nigeria Journal of Pure and Applied Physics

    African Journals Online (AJOL)

    Nigeria Journal of Pure and Applied Physics (NJPAP) is a journal dedicated to the ... Variations of surface temparature with solar activity at two stations in the tropics ... Activation energy of psuedobinary alloy of Al-Bi-Se mixed systems · EMAIL ...