WorldWideScience

Sample records for pulsed filtered cathodic

  1. Transparent and conductive indium doped cadmium oxide thin films prepared by pulsed filtered cathodic arc deposition

    Energy Technology Data Exchange (ETDEWEB)

    Zhu Yuankun, E-mail: yuan.kun.zhu@gmail.com [Center for Composite Materials and Structures, Harbin Institute of Technology, Harbin 150080 (China); Plasma Applications Group, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Mendelsberg, Rueben J. [Plasma Applications Group, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Molecular Foundry, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Zhu Jiaqi, E-mail: zhujq@hit.edu.cn [Center for Composite Materials and Structures, Harbin Institute of Technology, Harbin 150080 (China); Han Jiecai [Center for Composite Materials and Structures, Harbin Institute of Technology, Harbin 150080 (China); Anders, Andre [Plasma Applications Group, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer High quality CdO:In films were prepared on glass by pulsed filtered cathodic arc. Black-Right-Pointing-Pointer 230 nm thick films show low resistivity of 7.23 Multiplication-Sign 10{sup -5} {Omega} cm and mobility of 142 cm{sup 2}/Vs. Black-Right-Pointing-Pointer In-doping significantly improves the conductivity and extends the transparent range. Black-Right-Pointing-Pointer Film crystalline quality is maintained with increasing In concentration. Black-Right-Pointing-Pointer The pulsed arc-grown CdO:In show excellent reproducibility of film properties. - Abstract: Indium doped cadmium oxide (CdO:In) films with different In concentrations were prepared on low-cost glass substrates by pulsed filtered cathodic arc deposition (PFCAD). It is shown that polycrystalline CdO:In films with smooth surface and dense structure are obtained. In-doping introduces extra electrons leading to remarkable improvements of electron mobility and conductivity, as well as improvement in the optical transmittance due to the Burstein-Moss effect. CdO:In films on glass substrates with thickness near 230 nm show low resistivity of 7.23 Multiplication-Sign 10{sup -5} {Omega} cm, high electron mobility of 142 cm{sup 2}/Vs, and mean transmittance over 80% from 500 to 1250 nm (including the glass substrate). These high quality pulsed arc-grown CdO:In films are potentially suitable for high efficiency multi-junction solar cells that harvest a broad range of the solar spectrum.

  2. Langmuir probe study of a titanium pulsed filtered cathodic arc discharge

    Energy Technology Data Exchange (ETDEWEB)

    Andruczyk, D [School of Physics, University of Sydney, NSW 2006 (Australia); Tarrant, R N [School of Physics, University of Sydney, NSW 2006 (Australia); James, B W [School of Physics, University of Sydney, NSW 2006 (Australia); Bilek, M M M [School of Physics, University of Sydney, NSW 2006 (Australia); Warr, G B [School of Physics, University of Sydney, NSW 2006 (Australia)

    2006-08-01

    A Langmuir probe has been used to make measurements of plasma parameters as a function of time at the substrate position in a magnetically-filtered pulsed cathodic arc discharge. Electron density, n{sub e}, and effective electron temperature, T{sub eff}, were calculated as a function of time from the I-V curves. The Druyvesteyn method was used to determine the electron energy distribution. Ion density was calculated using the assumption of plasma quasi-neutrality and an average ion charge state. Results show that over the plateau region (350-600 {mu}s) of the pulse, the electron energy distribution is Maxwellian with T{sub eff} = T{sub e} = (10 {+-} 1) eV. During the rise and fall times of the pulse, the electron energy distribution is non-Maxwellian with an effective temperature of up to 15 to 20 eV during the rise time and {approx}7 eV during the fall time. The electron density during the plateau is n{sub e} = (3.0-6.0 {+-} 0.5) x 10{sup 17} m{sup -3}.

  3. Raman Spectroscopy of DLC/a-Si Bilayer Film Prepared by Pulsed Filtered Cathodic Arc

    Directory of Open Access Journals (Sweden)

    C. Srisang

    2012-01-01

    Full Text Available DLC/a-Si bilayer film was deposited on germanium substrate. The a-Si layer, a seed layer, was firstly deposited on the substrate using DC magnetron sputtering and DLC layer was then deposited on the a-Si layer using pulsed filtered cathodic arc method. The bilayer films were deposited with different DLC/a-Si thickness ratios, including 2/2, 2/6, 4/4, 6/2, and 9/6. The effect of DLC/a-Si thickness ratios on the sp3 content of DLC was analyzed by Raman spectroscopy. The results show that a-Si layer has no effect on the structure of DLC film. Furthermore, the upper shift in G wavenumber and the decrease in ID/IG inform that sp3 content of the film is directly proportional to DLC thickness. The plot modified from the three-stage model informed that the structural characteristics of DLC/a-Si bilayer films are located close to the tetrahedral amorphous carbon. This information may be important for analyzing and developing bilayer protective films for future hard disk drive.

  4. Filtered pulsed cathodic arc deposition of fullerene-like carbon and carbon nitride films

    Energy Technology Data Exchange (ETDEWEB)

    Tucker, Mark D., E-mail: martu@ifm.liu.se; Broitman, Esteban; Näslund, Lars-Åke; Hultman, Lars; Rosen, Johanna [Thin Film Physics Division, Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-58183 Linköping (Sweden); Czigány, Zsolt [Institute for Technical Physics and Materials Science, RCNS, Hungarian Academy of Sciences, P.O. Box 49, H-1525 Budapest (Hungary)

    2014-04-14

    Carbon and carbon nitride films (CN{sub x}, 0 ≤ x ≤ 0.26) were deposited by filtered pulsed cathodic arc and were investigated using transmission electron microscopy and X-ray photoelectron spectroscopy. A “fullerene-like” (FL) structure of ordered graphitic planes, similar to that of magnetron sputtered FL-CN{sub x} films, was observed in films deposited at 175 °C and above, with N{sub 2} pressures of 0 and 0.5 mTorr. Higher substrate temperatures and significant nitrogen incorporation are required to produce similar FL structure by sputtering, which may, at least in part, be explained by the high ion charge states and ion energies characteristic of arc deposition. A gradual transition from majority sp{sup 3}-hybridized films to sp{sup 2} films was observed with increasing substrate temperature. High elastic recovery, an attractive characteristic mechanical property of FL-CN{sub x} films, is evident in arc-deposited films both with and without nitrogen content, and both with and without FL structure.

  5. Filtered pulsed cathodic arc deposition of fullerene-like carbon and carbon nitride films

    Science.gov (United States)

    Tucker, Mark D.; Czigány, Zsolt; Broitman, Esteban; Näslund, Lars-Åke; Hultman, Lars; Rosen, Johanna

    2014-04-01

    Carbon and carbon nitride films (CNx, 0 ≤ x ≤ 0.26) were deposited by filtered pulsed cathodic arc and were investigated using transmission electron microscopy and X-ray photoelectron spectroscopy. A "fullerene-like" (FL) structure of ordered graphitic planes, similar to that of magnetron sputtered FL-CNx films, was observed in films deposited at 175 °C and above, with N2 pressures of 0 and 0.5 mTorr. Higher substrate temperatures and significant nitrogen incorporation are required to produce similar FL structure by sputtering, which may, at least in part, be explained by the high ion charge states and ion energies characteristic of arc deposition. A gradual transition from majority sp3-hybridized films to sp2 films was observed with increasing substrate temperature. High elastic recovery, an attractive characteristic mechanical property of FL-CNx films, is evident in arc-deposited films both with and without nitrogen content, and both with and without FL structure.

  6. Filtered cathodic arc source

    Science.gov (United States)

    Falabella, Steven; Sanders, David M.

    1994-01-01

    A continuous, cathodic arc ion source coupled to a macro-particle filter capable of separation or elimination of macro-particles from the ion flux produced by cathodic arc discharge. The ion source employs an axial magnetic field on a cathode (target) having tapered sides to confine the arc, thereby providing high target material utilization. A bent magnetic field is used to guide the metal ions from the target to the part to be coated. The macro-particle filter consists of two straight solenoids, end to end, but placed at 45.degree. to one another, which prevents line-of-sight from the arc spot on the target to the parts to be coated, yet provides a path for ions and electrons to flow, and includes a series of baffles for trapping the macro-particles.

  7. Characterization of SiC in DLC/a-Si films prepared by pulsed filtered cathodic arc using Raman spectroscopy and XPS

    Energy Technology Data Exchange (ETDEWEB)

    Srisang, C. [Department of Physics, Faculty of Science, King Mongkut' s University of Technology Thonburi, Bangkok 10140 (Thailand); Western Digital (Thailand) Company Limited, Ayuthaya 13160 (Thailand); Thailand Center of Excellence in Physics, CHE, Ministry of Education, Bangkok 10400 (Thailand); Asanithi, P. [Department of Physics, Faculty of Science, King Mongkut' s University of Technology Thonburi, Bangkok 10140 (Thailand); Siangchaew, K. [Western Digital (Thailand) Company Limited, Ayuthaya 13160 (Thailand); Pokaipisit, A. [Department of Physics, Faculty of Science, King Mongkut' s University of Technology Thonburi, Bangkok 10140 (Thailand); Thailand Center of Excellence in Physics, CHE, Ministry of Education, Bangkok 10400 (Thailand); Limsuwan, P., E-mail: opticslaser@yahoo.com [Department of Physics, Faculty of Science, King Mongkut' s University of Technology Thonburi, Bangkok 10140 (Thailand); Thailand Center of Excellence in Physics, CHE, Ministry of Education, Bangkok 10400 (Thailand)

    2012-05-15

    DLC/a-Si films were deposited on germanium substrates. a-Si film was initially deposited as a seed layer on the substrate using DC magnetron sputtering. DLC film was then deposited on the a-Si layer via a pulsed filtered cathodic arc (PFCA) system. In situ ellipsometry was used to monitor the thicknesses of the growth films, allowing a precise control over the a-Si and DLC thicknesses of 6 and 9 nm, respectively. It was found that carbon atoms implanting on a-Si layer act not only as a carbon source for DLC formation, but also as a source for SiC formation. The Raman peak positions at 796 cm{sup -1} and 972 cm{sup -1} corresponded to the LO and TO phonon modes of SiC, respectively, were observed. The results were also confirmed using TEM, XPS binding energy and XPS depth profile analysis.

  8. A pulsed cathodic arc spacecraft propulsion system

    Energy Technology Data Exchange (ETDEWEB)

    Neumann, P R C; Bilek, M M M; Tarrant, R N; McKenzie, D R [School of Physics, University of Sydney, NSW 2006 Australia (Australia)

    2009-11-15

    We investigate the use of a centre-triggered cathodic arc as a spacecraft propulsion system that uses an inert solid as a source of plasma. The cathodic vacuum arc produces almost fully ionized plasma with a high exhaust velocity (>10{sup 4} m s{sup -1}), giving a specific impulse competitive with other plasma or ion thrusters. A centre trigger design is employed that enables efficient use of cathode material and a high pulse-to-pulse repeatability. We compare three anode geometries, two pulse current profiles and two pulse durations for their effects on impulse generation, energy and cathode material usage efficiency. Impulse measurement is achieved through the use of a free-swinging pendulum target constructed from a polymer material. Measurements show that impulse is accurately controlled by varying cathode current. The cylindrical anode gave the highest energy efficiency. Cathode usage is optimized by choosing a sawtooth current profile. There is no requirement for an exhaust charge neutralization system.

  9. Filtered cathodic arc deposition apparatus and method

    Science.gov (United States)

    Krauss, Alan R.

    1999-01-01

    A filtered cathodic arc deposition method and apparatus for the production of highly dense, wear resistant coatings which are free from macro particles. The filtered cathodic arc deposition apparatus includes a cross shaped vacuum chamber which houses a cathode target having an evaporable surface comprised of the coating material, means for generating a stream of plasma, means for generating a transverse magnetic field, and a macro particle deflector. The transverse magnetic field bends the generated stream of plasma in the direction of a substrate. Macro particles are effectively filtered from the stream of plasma by traveling, unaffected by the transverse magnetic field, along the initial path of the plasma stream to a macro particle deflector. The macro particle deflector has a preformed surface which deflects macro particles away from the substrate.

  10. Pulsed current cathodic protection of well casings

    Energy Technology Data Exchange (ETDEWEB)

    Bich, N.N. [Shell Canada Ltd., Fort Saskatchewan, Alberta (Canada). Scotford Complex; Bauman, J. [Shell Canada Ltd., Cochrane, Alberta (Canada). Jumping Pound Complex

    1995-04-01

    Electric pulses of several hundred volts, applied for very brief periods of time, several thousand times per second, are more effective and economical than conventional steady-state DC currents in protecting deep and/or close-spaced well casings against external corrosion. More uniform current distribution, greater depth of protection, reduced stray current interference, and small anode bed requirements are the main benefits of pulsed technology. Operating principles, equivalent electrical circuits, design considerations, and field cathodic protection logging experience is reviewed.

  11. Pulsed microhollow cathode discharge excimer sources

    Science.gov (United States)

    Moselhy, Mohamed; Shi, Wenhui; Strak, Robert H.; Schoenbach, Karl H.

    2001-10-01

    Microhollow cathode discharges (MHCDs) are non-equilibrium, high-pressure gas discharges between perforated electrodes separated by a dielectric layer. Typical dimensions for the electrode foil thickness and hole diameter are 100 μm. Direct current experiments in xenon, argon, neon, helium, argon fluoride, and xenon chloride [1,2] have been performed. The excimer efficiency varies between 1 % and 9 %. Pulsed operation allowed us to increase the current from 8 mA (dc) to approximately 80 mA (pulsed with a pulse width of 700 μs), limited by the onset of instabilities. The total excimer power was found to increase linearly with current, however, the radiant emittance and efficiency stayed constant. Reducing the pulse duration into the nanosecond range allowed us to increase the current into the ampere range. The maximum measured excimer power was 2.75 W per microdischarge. The maximum radiant emittance was 15 W/cm^2 and the efficiency reached values of 20 %. This effect is assumed to be due to non-equilibrium electron heating in the high-pressure plasma [3]. This work was supported by the National Science Foundation under grant # CTS0078618. 1. Karl H. Schoenbach, Ahmed El-Habachi, Mohamed M. Moselhy, Wenhui Shi, and Robert H. Stark, Physics of Plasmas 7, 2186 (2000). 2. P. Kurunczi, J. Lopez, H. Shah, and K. Becker, Int. J. Mass Spectrom. 205, 277 (2001). 3. Robert H. Stark and Karl H. Schoenbach, J. Appl. Phys. 89, 3568 (2001).

  12. Structural, optical and electrical properties of N-doped ZnO thin films prepared by thermal oxidation of pulsed filtered cathodic vacuum arc deposited Zn{sub x}N{sub y} films

    Energy Technology Data Exchange (ETDEWEB)

    Erdogan, N.H.; Kara, K.; Ozdamar, H. [Physics Department, Cukurova University, 01330 Adana (Turkey); Kavak, H., E-mail: hkavak@cu.edu.tr [Physics Department, Cukurova University, 01330 Adana (Turkey); Esen, R. [Physics Department, Cukurova University, 01330 Adana (Turkey); Karaagac, H. [Physics Department, Middle East Technical University, 06531 Ankara (Turkey)

    2011-09-08

    Graphical abstract: Highlights: > Thermal oxidation of Zn{sub x}N{sub y} method is used to obtain N doped ZnO. > N acceptors in ZnO is not sufficiently activated at oxidation temperature below 350 deg. C. > Oxidation treatment at 450 deg. C activates more N acceptors in ZnO. > Oxidation treatment at high temperatures above 550 deg. C reduces the N concentration in the ZnO thin film. - Abstract: In this study, N-doped ZnO thin films were fabricated by oxidation of Zn{sub x}N{sub y} films. The Zn{sub x}N{sub y} thin films were deposited on glass substrates by pulsed filtered cathodic vacuum arc deposition (PFCVAD) using metallic zinc wire (99.999%) as a cathode target in pure nitrogen plasma. The influence of oxidation temperature, on the electrical, structural and optical properties of N-doped ZnO films was investigated. P-type conduction was achieved for the N-doped ZnO obtained at 450 deg. C by oxidation of Zn{sub x}N{sub y}, with a resistivity of 16.1 {Omega} cm, hole concentration of 2.03 x 10{sup 16} cm{sup -3} and Hall mobility of 19 cm{sup 2}/V s. X-ray photoelectron spectroscopy (XPS) analysis confirmed the incorporation of N into the ZnO films. X-ray diffraction (XRD) pattern showed that the films as-deposited and oxidized at 350 deg. C were amorphous. However, the oxidized films in air atmosphere at 450-550 deg. C were polycrystalline without preferential orientation. In room temperature photoluminescence (PL) spectra, an ultraviolet (UV) peak was seen for all the samples. In addition, a broad deep level emission was observed.

  13. Pulsed photoelectric field emission from needle cathodes

    CERN Document Server

    Hernandez-Garcia, C

    2002-01-01

    Experiments have been carried out to measure the current emitted by tungsten needles with 1-mu m tip radius operated up to 50 kV. This corresponds to electric fields in the order of 10 sup 9 to 10 sup 1 sup 0 V/m. The needles were illuminated with 10-ns laser pulses at 532, 355 and 266 nm. The laser intensity was varied from 10 sup 1 sup 0 to 10 sup 1 sup 2 W/m sup 2 , limited by damage to the needle tip. The observed quantum efficiency depends on the wavelength and the electric field, approaching unity at the highest electric fields when illuminated at 266 nm. Peak currents up to 100 mA were observed in nanosecond pulses, corresponding to an estimated brightness of 10 sup 1 sup 6 A/m sup 2 sr. Since the current is controlled by the laser intensity, with only a weak voltage dependence, these cathodes can be used for infrared and ultraviolet tabletop free-electron lasers and other applications that demand short electron-beam pulses with high brightness.

  14. Optimal filter bandwidth for pulse oximetry

    Science.gov (United States)

    Stuban, Norbert; Niwayama, Masatsugu

    2012-10-01

    Pulse oximeters contain one or more signal filtering stages between the photodiode and microcontroller. These filters are responsible for removing the noise while retaining the useful frequency components of the signal, thus improving the signal-to-noise ratio. The corner frequencies of these filters affect not only the noise level, but also the shape of the pulse signal. Narrow filter bandwidth effectively suppresses the noise; however, at the same time, it distorts the useful signal components by decreasing the harmonic content. In this paper, we investigated the influence of the filter bandwidth on the accuracy of pulse oximeters. We used a pulse oximeter tester device to produce stable, repetitive pulse waves with digitally adjustable R ratio and heart rate. We built a pulse oximeter and attached it to the tester device. The pulse oximeter digitized the current of its photodiode directly, without any analog signal conditioning. We varied the corner frequency of the low-pass filter in the pulse oximeter in the range of 0.66-15 Hz by software. For the tester device, the R ratio was set to R = 1.00, and the R ratio deviation measured by the pulse oximeter was monitored as a function of the corner frequency of the low-pass filter. The results revealed that lowering the corner frequency of the low-pass filter did not decrease the accuracy of the oxygen level measurements. The lowest possible value of the corner frequency of the low-pass filter is the fundamental frequency of the pulse signal. We concluded that the harmonics of the pulse signal do not contribute to the accuracy of pulse oximetry. The results achieved by the pulse oximeter tester were verified by human experiments, performed on five healthy subjects. The results of the human measurements confirmed that filtering out the harmonics of the pulse signal does not degrade the accuracy of pulse oximetry.

  15. Evaluation of externally heated pulsed MPD thruster cathodes

    Science.gov (United States)

    Myers, Roger M.; Domonkos, Matthew; Gallimore, Alec D.

    1993-01-01

    Recent interest in solar electric orbit transfer vehicles (SEOTV's) has prompted a reevaluation of pulsed magnetoplasmadynamic (MPD) thruster systems due to their ease of power scaling and reduced test facility requirements. In this work the use of externally heated cathodes was examined in order to extend the lifetime of these thrusters to the 1000 to 3000 hours required for SEOTV missions. A pulsed MPD thruster test facility was assembled, including a pulse-forming network (PFN), ignitor supply and propellant feed system. Results of cold cathode tests used to validate the facility, PFN, and propellant feed system design are presented, as well as a preliminary evaluation of externally heated impregnated tungsten cathodes. The cold cathode thruster was operated on both argon and nitrogen propellants at peak discharge power levels up to 300 kW. The results confirmed proper operation of the pulsed thruster test facility, and indicated that large amounts of gas were evolved from the BaO-CaO-Al2O3 cathodes during activation. Comparison of the expected space charge limited current with the measured vacuum current when using the heated cathode indicate that either that a large temperature difference existed between the heater and the cathode or that the surface work function was higher than expected.

  16. Self-pulsing of a micro thin cathode discharge

    CERN Document Server

    Gebhardt, Markus; Hemke, Torben; Brinkmann, Ralf Peter; Mussenbrock, Thomas

    2011-01-01

    Microplasmas operated at atmospheric pressure show a number of peculiar dynamic phenomena. One of these phenomena is self-pulsing, which is characterized by intrinsic pulsing behavior of a DC driven plasma discharge. This work focuses on the numerical simulation of self-pulsing in a micro thin cathode discharge operated in atmospheric pressure argon. By means of a hybrid plasma model we show self-pulsing of the discharge in the expected MHz frequency range and described its actual origin.

  17. Fuel cell cathode air filters: Methodologies for design and optimization

    Science.gov (United States)

    Kennedy, Daniel M.; Cahela, Donald R.; Zhu, Wenhua H.; Westrom, Kenneth C.; Nelms, R. Mark; Tatarchuk, Bruce J.

    Proton exchange membrane (PEM) fuel cells experience performance degradation, such as reduction in efficiency and life, as a result of poisoning of platinum catalysts by airborne contaminants. Research on these contaminant effects suggests that the best possible solution to allowing fuel cells to operate in contaminated environments is by filtration of the harmful contaminants from the cathode air. A cathode air filter design methodology was created that connects properties of cathode air stream, filter design options, and filter footprint, to a set of adsorptive filter parameters that must be optimized to efficiently operate the fuel cell. Filter optimization requires a study of the trade off between two causal factors of power loss: first, a reduction in power production due to poisoning of the platinum catalyst by chemical contaminants and second, an increase in power requirements to operate the air compressor with a larger pressure drop from additional contaminant filtration. The design methodology was successfully applied to a 1.2 kW fuel cell using a programmable algorithm and predictions were made about the relationships between inlet concentration, breakthrough time, filter design, pressure drop, and compressor power requirements.

  18. Simple filtered repetitively pulsed vacuum arc plasma source

    Science.gov (United States)

    Chekh, Yu.; Zhirkov, I. S.; Delplancke-Ogletree, M. P.

    2010-02-01

    A very simple design of cathodic filtered vacuum arc plasma source is proposed. The source without filter has only four components and none of them require precise machining. The source operates in a repetitively pulsed regime, and for laboratory experiments it can be used without water cooling. Despite the simple construction, the source provides high ion current at the filter outlet reaching 2.5% of 400 A arc current, revealing stable operation in a wide pressure range from high vacuum to oxygen pressure up to more than 10-2 mbar. There is no need in complicated power supply system for this plasma source, only one power supply can be used to ignite the arc, to provide the current for the arc itself, to generate the magnetic field in the filter, and provide its positive electric biasing without any additional high power resistance.

  19. Cathodic protection of well casings by pulsed current

    Energy Technology Data Exchange (ETDEWEB)

    Bich, N.N. [Shell Canada Ltd., Fort Saskatchewan, Alberta (Canada). Scotford Complex; Bauman, J. [Shell Canada Ltd., Cochrane, Alberta (Canada). Jumping Pound Complex

    1994-12-31

    Electric pulses of several hundred volts, applied for very brief periods of time, several thousand times per second, are more effective and economical than conventional DC currents in protecting deep and/or close spaced well casings against external corrosion. More uniform current distribution, greater depth of protection, reduced stray current interference, and smaller anode bed requirements are the main benefits of pulsed technology. Operating principles, equivalent electrical circuits, design considerations and field cathodic protection logging experience will be reviewed.

  20. Silicon etch with chromium ions generated by a filtered or non-filtered cathodic arc discharge.

    Science.gov (United States)

    Scopece, Daniele; Döbeli, Max; Passerone, Daniele; Maeder, Xavier; Neels, Antonia; Widrig, Beno; Dommann, Alex; Müller, Ulrich; Ramm, Jürgen

    2016-01-01

    The pre-treatment of substrate surfaces prior to deposition is important for the adhesion of physical vapour deposition coatings. This work investigates Si surfaces after the bombardment by energetic Cr ions which are created in cathodic arc discharges. The effect of the pre-treatment is analysed by X-ray diffraction, Rutherford backscattering spectroscopy, scanning electron microscopy and in-depth X-ray photoemission spectroscopy and compared for Cr vapour produced from a filtered and non-filtered cathodic arc discharge. Cr coverage as a function of ion energy was also predicted by TRIDYN Monte Carlo calculations. Discrepancies between measured and simulated values in the transition regime between layer growth and surface removal can be explained by the chemical reactions between Cr ions and the Si substrate or between the substrate surface and the residual gases. Simulations help to find optimum and more stable parameters for specific film and substrate combinations faster than trial-and-error procedure.

  1. Cold-cathode, pulsed-power plasma discharge switch

    Science.gov (United States)

    Goebel, Dan M.

    1996-09-01

    CROSSATRONTMmodulator switches are cold-cathode, grid-controlled, plasma-discharge devices that are used for thyratron and hard-tube replacement in high-voltage, pulsed-power applications. CROSSATRON modulator switches have been used to produce square pulses of up to 100 kV and 1000 A, and CROSSATRON laser-discharge switches have switched peak discharge currents of up to 10 kA at 40 kV. The major advantage that CROSSATRON switches offer over other plasma switches is a rapid deionization time that permits high pulse-repetition frequencies (103 to 106 pulses per second depending on the application), and a long life associated with the cold-cathode plasma production mechanism. Compared to hard tubes, CROSSATRON switches have a relatively low forward voltage drop (500 V), the ability to close and open up to 1 kA of peak current, and lower grid-drive power requirements. In this article, we describe the physical mechanisms for how the switch works based on simple models and experimental data. The design of CROSSATRON switches is explained, and characteristic performance in closing and opening applications is described and explained.

  2. Filtered cathodic arc deposition with ion-species-selectivebias

    Energy Technology Data Exchange (ETDEWEB)

    Anders, Andre; Pasaja, Nitisak; Sansongsiri, Sakon; Lim, SunnieH.N.

    2006-10-05

    A dual-cathode arc plasma source was combined with acomputer-controlled bias amplifier such as to synchronize substrate biaswith the pulsed production of plasma. In this way, bias can be applied ina material-selective way. The principle has been applied to the synthesismetal-doped diamond-like carbon films, where the bias was applied andadjusted when the carbon plasma was condensing, and the substrate was atground when the metal was incorporated. In doing so, excessive sputteringby too-energetic metal ions can be avoided while the sp3/sp2 ratio can beadjusted. It is shown that the resistivity of the film can be tuned bythis species-selective bias. The principle can be extended tomultiple-material plasma sources and complex materials

  3. Antibacterial efficacy of advanced silver-amorphous carbon coatings deposited using the pulsed dual cathodic arc technique

    Energy Technology Data Exchange (ETDEWEB)

    Endrino, J L; Anders, A; Albella, J M; Horton, J A; Horton, T H; Ayyalasomayajula, P R; Allen, M, E-mail: jlendrino@icmm.csic.es

    2010-11-01

    Amorphous carbon (a-C) also referred as diamond-like carbon (DLC) films are well known to be a biocompatible material with good chemical in ertness; this makes it a strong candidate to be used as a matrix that embeds metallic elements with an antimicrobial effect. We have deposited as et of a-C:Ag films using a dual-cathode pulsed filtered cathodic arc source, the arc pulse frequency of the silver and graphite cathodes was controlled in order to obtain samples with various silver contents. In this study, we show the deposition of silver and carbon ions using this technique and analyze the advantages of incorporating silver into a-C by studying the antimicrobial properties against staphylococcus of samples deposited on Ti{sub 6}Al{sub 4}V coupons and evaluated using 24-well tissue culture plates.

  4. Hollow cathode lamp based Faraday anomalous dispersion optical filter.

    Science.gov (United States)

    Pan, Duo; Xue, Xiaobo; Shang, Haosen; Luo, Bin; Chen, Jingbiao; Guo, Hong

    2016-07-15

    The Faraday anomalous dispersion optical filter (FADOF), which has acquired wide applications, is mainly limited to some gaseous elements and low melting-point metals before, for the restriction of the attainable atomic density. In conventional FADOF systems a high atomic density is usually achieved by thermal equilibrium at the saturated vapor pressure, hence for elements with high melting-points a high temperature is required. To avoid this restriction, we propose a scheme of FADOF based on the hollow cathode lamp (HCL), instead of atomic vapor cells. Experimental results in strontium atoms verified this scheme, where a transmission peak corresponding to the (88)Sr (5s(2))(1)S0 - (5s5p)(1)P1 transition (461 nm) is obtained, with a maximum transmittance of 62.5% and a bandwith of 1.19 GHz. The dependence of transmission on magnetic field and HCL discharge current is also studied. Since the state-of-art commercial HCLs cover about 70 elements, this scheme can greatly expand the applications of FADOFs, and the abundant atomic transitions they provide bring the HCL based FADOFs potential applications for frequency stabilization.

  5. Macroparticles Reduction Using Filter Free Cathodic Vacuum Arc Deposition Method in ZnO Thin Films.

    Science.gov (United States)

    Yuvakkumar, R; Peranantham, P; Nathanael, A Joseph; Nataraj, D; Mangalaraj, D; Hong, Sun Ig

    2015-03-01

    We report a new method to reduce macroparticles in ZnO thin films using filter free cathodic vacuum arc deposition without using any cooling arrangements operated at low arc current. The detailed mechanism has been proposed to reduce macroparticles during thin film deposition. The successful reduction of macroparticles was confirmed employing FESEM-EDX studies. FESEM images of ZnO thin films deposited with cathode spot to substrate distance from 10 to 20 cm revealed that the population of the macroparticles were reduced with the increase of cathode spot to substrate distances at low arc current. The prepared ZnO films were characterised and showed good structural and optical properties.

  6. Self-pulsing in a low-current hollow cathode discharge: From Townsend to glow discharge

    Energy Technology Data Exchange (ETDEWEB)

    Qin, Yu [School of Physics, Beijing Institute of Technology, Beijing 100081 (China); School of Aerospace Engineering, Beijing Institute of Technology, Beijing 100081 (China); Xie, Kan, E-mail: xiekan@bit.edu.cn [School of Aerospace Engineering, Beijing Institute of Technology, Beijing 100081 (China); Zhang, Yu; Ouyang, Jiting [School of Physics, Beijing Institute of Technology, Beijing 100081 (China)

    2016-02-15

    We investigate the self-pulsing phenomenon of a low current cavity discharge in a cylindrical hollow cathode in pure argon. The waveforms of pulsed current and voltage are measured, and the time-averaged and time-resolved images of hollow cathode discharge are recorded by using high-speed intensified charge coupled device camera. The results show that the self-pulsing is a mode transition between low-current stage of Townsend discharge and high-current stage of glow discharge. During the self-pulsing, the current rising time relates to the dissipation of space charges, and the decay time relates to the reconstruction of the virtual anode by the accumulation of positive ions. Whether or not space charges can form and keep the virtual anode is responsible for the discharge mode and hence plays an important role in the self-pulsing phenomenon in low current hollow cathode discharge.

  7. Design and characterization of the annular cathode high current pulsed electron beam source for circular components

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Wei; Wang, Langping, E-mail: aplpwang@hit.edu.cn; Wang, Xiaofeng

    2016-08-01

    Highlights: • An annular cathode for HCPEB irradiation of circular components was designed. • The processing window for the annular cathode is obtained. • Irradiation thickness uniformity along the circumferential direction exceeds 90%. - Abstract: In order to irradiate circular components with high current pulsed electron beam (HCPEB), an annular cathode based on carbon fiber bunches was designed and fabricated. Using an acceleration voltage of 25 kV, the maximum pulsed irradiation current and energy of this annular cathode can reach 7.9 kA and 300 J, respectively. The irradiation current density distribution of the annular cathode HCPEB source measured along the circumferential direction shows that the annular cathode has good emission uniformity. In addition, four 9310 steel substrates fixed uniformly along the circumferential direction of a metal ring substrate were irradiated by this annular cathode HCPEB source. The surface and cross-section morphologies of the irradiated samples were characterized by scanning electron microscopy (SEM). SEM images of the surface reveal that crater and surface undulation have been formed, which hints that the irradiation energy of the HCPEB process is large enough for surface modification of 9310 steel. Meanwhile, SEM cross-section images exhibit that remelted layers with a thickness of about 5.4 μm have been obtained in all samples, which proves that a good practical irradiation uniformity can be achieved by this annular cathode HCPEB source.

  8. Conventional and Pulse Cathodic Protection of Reinforced Concrete: Electrochemical Approach and Microstructural Investigations

    NARCIS (Netherlands)

    Koleva, D.A.; Hu, J.; Van Breugel, K.; De Wit, J.H.W.; Boshkov, N.

    2006-01-01

    An improved cathodic protection (CP), based on pulse regime was investigated in reinforced concrete, compared to conventional CP. Both regimes used CP current in the range of 2 to15 mA/m2. A voltage-to-current converter maintained the pulse current, the latter adjusted with duty cycle of 12% to 50 %

  9. Non-Thermionic Cathode for High Power Long Pulse, Long Lifetime Magnetrons

    Science.gov (United States)

    2010-11-18

    switched with an SCR. The coil produces a 3 kG magnetic field with a 20mS critically damped waveform. This is sufficient to allow flux penetration...that the conventional thermionic cathode doses not provide acceptable electron emission for operation in the HPM power levels (> 100Mw). In this work...TECHNICAL REPORT AFOSR CONTRACT: FA9550-09-C-0127 “Non- Thermionic Cathode for High Power Long Pulse, Long Lifetime Magnetrons” Miles Collins Clark

  10. Vacuum Outgassing Behavior of Carbon Nanotube Cathode with High-Intensity Pulsed Electron Emission

    Science.gov (United States)

    Shen, Yi; Zhang, Huang; Xia, Liansheng; Liu, Xingguang; Pan, Haifeng; Lv, Lu; Yang, Anmin; Shi, Jinshui; Zhang, Linwen; Deng, Jianjun

    2015-02-01

    Experimental investigations on the vacuum outgassing of a carbon nanotube (CNT) cathode with high-intensity pulsed electron emission on a 2 MeV linear induction accelerator injector are presented. Under the 1.60 MV diode voltage, the CNT cathode could provide 1.67 kA electron beam with the amount of outgassing of about 0.51 Pa·L. It is found that the amount of outgassing, which determines the cathode emission current, depends on the diode voltage and the vacuum.

  11. Dual-Function Air Cathode for Metal-Air Batteries with Pulse-Power Capability

    Science.gov (United States)

    2013-01-28

    Rolison , L. F. Nazar , MRS Bull. 2011 , 36 , 486 . [ 2 ] D. Linden , Ed., Handbook of Batteries : Second Edition , McGraw Hill , New...Dual-Function Air Cathode for Metal–Air Batteries with Pulse-Power Capability J. W. Long, C. N. Chervin, N. W. Kucko, E. S . Nelson, D. R. Rolison...Air Cathode for Metal-Air Batteries with Pulse-Power Capability 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) 5d

  12. Amp\\`ere-Class Pulsed Field Emission from Carbon-Nanotube Cathodes in a Radiofrequency Resonator

    CERN Document Server

    Mihalcea, D; Hartzell, J; Panuganti, H; Boucher, S M; Murokh, A; Piot, P; Thangaraj, J C T

    2015-01-01

    Pulsed field emission from cold carbon-nanotube cathodes placed in a radiofrequency resonant cavity was observed. The cathodes were located on the backplate of a conventional $1+\\frac{1}{2}$-cell resonant cavity operating at 1.3-GHz and resulted in the production of bunch train with maximum average current close to 0.7 Amp\\`ere. The measured Fowler-Nordheim characteristic, transverse emittance, and pulse duration are presented and, when possible, compared to numerical simulations. The implications of our results to high-average-current electron sources are briefly discussed.

  13. Corrosion and protection in reinforced concrete: pulse cathodic protection: an improved cost-effective alternative

    NARCIS (Netherlands)

    Koleva, D.A.

    2007-01-01

    Corrosion and protection in reinforced concrete. Pulse cathodic protection: an improved cost-effective alternative. The aim of the research project was to study the possibilities for establishing a new or improved electrochemical method for corrosion prevention/protection for reinforced concrete. Th

  14. Soliton filtering from a supercontinuum: a tunable femtosecond pulse source

    Energy Technology Data Exchange (ETDEWEB)

    Licea-Rodriguez, Jacob; Rangel-Rojo, Raul [Centro de Investigacion CientIfica y de Educacion Superior de Ensenada, Apartado Postal 2732, Ensenada B.C., 22860 (Mexico); Garay-Palmett, Karina, E-mail: rrangel@cicese.mx [Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, Apartado Postal 70-543, Mexico DF. 04510 (Mexico)

    2011-01-01

    In this article we report experimental results related with the generation of a supercontinuum in a microstructured fiber, from which the soliton with the longest wavelength is filtered out of the continuum and is used to construct a tunable ultrashort pulses source by varying the pump power. Pulses of an 80 fs duration (FWHM) from a Ti:sapphire oscillator were input into a 2 m long fiber to generate the continuum. The duration of the solitons at the fiber output was preserved by using a zero dispersion filtering system, which selected the longest wavelength soliton, while avoiding temporal spreading of the solitons. We present a complete characterization of the filtered pulses that are continuously tunable in the 850-1100 nm range. We also show that the experimental results have a qualitative agreement with theory. An important property of the proposed near-infrared pulsed source is that the soliton pulse energies obtained after filtering are large enough for applications in nonlinear microscopy.

  15. Metal cathode patterning for OLED by nanosecond pulsed laser ablation

    Institute of Scientific and Technical Information of China (English)

    LIU Chen; ZHU Guang-xi; LIU De-ming

    2006-01-01

    In this paper,nanosecond pulsed laser is introduced to selectively ablate away indium tin oxide film and metal film without destroying the underlying layers for fabricating organic light-emitting diodes. By varying density of energy, pulse number and width of the laser, the influence on morphology of the laser trenches of indium tin oxide and metal films are investigated. It is presented that uniform ablation trench can be obtained with 16 laser pulses at 0.15 J/cm2 for aluminum film and 10 laser pulses at 0.65 J/cm2 for indium tin oxide film. It is found that the characteristics of the organic light-emitting diodes prepared with laser ablation are almost the same as those of that prepared with conventional patterning method.

  16. Ion energy distributions in bipolar pulsed-dc discharges of methane measured at the biased cathode

    Energy Technology Data Exchange (ETDEWEB)

    Corbella, C; Rubio-Roy, M; Bertran, E; Portal, S; Pascual, E; Polo, M C; Andujar, J L, E-mail: corbella@ub.edu [FEMAN Group, IN2UB, Departament de Fisica Aplicada i Optica, Universitat de Barcelona, c/ MartI i Franques 1, 08028 Barcelona (Spain)

    2011-02-15

    The ion fluxes and ion energy distributions (IED) corresponding to discharges in methane (CH{sub 4}) were measured in time-averaged mode with a compact retarding field energy analyser (RFEA). The RFEA was placed on a biased electrode at room temperature, which was powered by either radiofrequency (13.56 MHz) or asymmetric bipolar pulsed-dc (250 kHz) signals. The shape of the resulting IED showed the relevant populations of ions bombarding the cathode at discharge parameters typical in the material processing technology: working pressures ranging from 1 to 10 Pa and cathode bias voltages between 100 and 200 V. High-energy peaks in the IED were detected at low pressures, whereas low-energy populations became progressively dominant at higher pressures. This effect is attributed to the transition from collisionless to collisional regimes of the cathode sheath as the pressure increases. On the other hand, pulsed-dc plasmas showed broader IED than RF discharges. This fact is connected to the different working frequencies and the intense peak voltages (up to 450 V) driven by the pulsed power supply. This work improves our understanding in plasma processes at the cathode level, which are of crucial importance for the growth and processing of materials requiring controlled ion bombardment. Examples of industrial applications with these requirements are plasma cleaning, ion etching processes during fabrication of microelectronic devices and plasma-enhanced chemical vapour deposition of hard coatings (diamond-like carbon, carbides and nitrides).

  17. Application of Taguchi method for the characterization of calcareous deposits formed by pulse cathodic protection

    Energy Technology Data Exchange (ETDEWEB)

    Zamanzade, M.; Shahrabi, T. [Department of Materials Science and Engineering, Faculty of Engineering, Tarbiat Modares University, Tehran (Iran); Gharacheh, E.A. [Department of Industrial Engineering, Faculty of Engineering, Tarbiat Modares University, Tehran (Iran)

    2007-09-15

    In this study, the Taguchi method, a powerful tool to design optimization for quality, is used to find the optimal process parameters of pulse cathodic protection system for the calcareous deposits' formation. An orthogonal array, main effect and the signal-to-noise (S/N) ratio are employed to investigate the process parameters in order to achieve optimum final current density. Through this study also the main process parameters that affect the calcareous deposits' formation can be found. Experiments were carried out to confirm the effectiveness of this approach. From the results, chronoamperometric measurements have been used to evaluate the influence of pulse cathodic protection on decreasing the required cathodic current for protection and also decreasing the surface coverage. The morphology of the formed deposits has been evaluated through scanning electron microscopy (SEM) and chemical analysis of the formed deposits has been performed using X-ray diffraction (XRD). It is found that the different environmental conditions, i.e., Ca{sup 2+} concentration, Mg{sup 2+} concentration, rotation speed, and temperature significantly affect the final required current density of the pulse cathodic protection. The optimum levels of parameters at different frequencies are also presented. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

  18. Optimum Filters and Pulsed Signal Storage Devices,

    Science.gov (United States)

    1982-05-05

    ya *ye initially, after vowels , and after b, b; e elsewhere. When written as 4 in Russian, transliterate as yd or 4. RUSSIAN AND ENGLISH...ratio only a decibel less. However, to achieve the maximum possible gain in the case of se- quences consisting of a large number of pulses, one must...F.,4 ; and ., 4 1=- 112 However, their value is low at n = * = 0.1 and comprises a fraction of a decibel . These losses increase as N increases. The

  19. Miniaturized cathodic arc plasma source

    Science.gov (United States)

    Anders, Andre; MacGill, Robert A.

    2003-04-15

    A cathodic arc plasma source has an anode formed of a plurality of spaced baffles which extend beyond the active cathode surface of the cathode. With the open baffle structure of the anode, most macroparticles pass through the gaps between the baffles and reflect off the baffles out of the plasma stream that enters a filter. Thus the anode not only has an electrical function but serves as a prefilter. The cathode has a small diameter, e.g. a rod of about 1/4 inch (6.25 mm) diameter. Thus the plasma source output is well localized, even with cathode spot movement which is limited in area, so that it effectively couples into a miniaturized filter. With a small area cathode, the material eroded from the cathode needs to be replaced to maintain plasma production. Therefore, the source includes a cathode advancement or feed mechanism coupled to cathode rod. The cathode also requires a cooling mechanism. The movable cathode rod is housed in a cooled metal shield or tube which serves as both a current conductor, thus reducing ohmic heat produced in the cathode, and as the heat sink for heat generated at or near the cathode. Cooling of the cathode housing tube is done by contact with coolant at a place remote from the active cathode surface. The source is operated in pulsed mode at relatively high currents, about 1 kA. The high arc current can also be used to operate the magnetic filter. A cathodic arc plasma deposition system using this source can be used for the deposition of ultrathin amorphous hard carbon (a-C) films for the magnetic storage industry.

  20. Influence of thermal heating on diamond-like carbon film properties prepared by filtered cathodic arc

    Energy Technology Data Exchange (ETDEWEB)

    Khamnualthong, N., E-mail: nattapornkh@gmail.com [Department of Physics, Faculty of Science, King Mongkut' s University of Technology Thonburi, Bangkok, 10140 (Thailand); Western Digital Thailand Co. Ltd, Ayutthaya, 13160 (Thailand); Siangchaew, K. [Western Digital Thailand Co. Ltd, Ayutthaya, 13160 (Thailand); Limsuwan, P. [Department of Physics, Faculty of Science, King Mongkut' s University of Technology Thonburi, Bangkok, 10140 (Thailand); Thailand Center of Excellence in Physics, CHE, Ministry of Education, Bangkok 10400 (Thailand)

    2013-10-01

    Tetrahedral amorphous diamond-like carbon (ta-DLC) films were deposited on magnetic recording heads using the filtered cathodic arc method. The deposited film thickness was on the order of several nanometers. The DLC films were then annealed to 100 °C–300 °C for 30 and 60 min, and the structure of the ta-DLC films was investigated using Raman spectroscopy, where the gross changes were observed in the Raman D and G peaks. Detailed interpretation concluded that there was sp{sup 2} clustering as a function of temperature, and there was no sp{sup 3}-to-sp{sup 2} conversion after heating up to 300 °C. Furthermore, X-ray photoelectron spectroscopy suggested that oxidation of both the ta-DLC film and the adhesion layer occurs at 300 °C. Additionally, more film wear was observed with heating as measured by a nanoindenter. - Highlights: • Tetrahedral-amorphous diamond-like carbon (ta-DLC) by filtered cathodic arc • ta-DLC used in magnetic recording head as head overcoat • ta-DLC thickness range of less than 2 nm • ta-DLC property dependence on heating • Temperature effect range of up to 300 °C.

  1. Operating modes of a hydrogen ion source based on a hollow-cathode pulsed Penning discharge

    Energy Technology Data Exchange (ETDEWEB)

    Oks, E. M. [Institute of High Current Electronics, Siberian Branch of Russian Academy of Science, Tomsk (Russian Federation); Tomsk State University of Control System and Radioelectronics, Tomsk (Russian Federation); Shandrikov, M. V., E-mail: shandrikov@opee.hcei.tsc.ru; Vizir, A. V. [Institute of High Current Electronics, Siberian Branch of Russian Academy of Science, Tomsk (Russian Federation)

    2016-02-15

    An ion source based on a hollow-cathode Penning discharge was switched to a high-current pulsed mode (tens of amperes and tens of microseconds) to produce an intense hydrogen ion beam. With molecular hydrogen (H{sub 2}), the ion beam contained three species: H{sup +}, H{sub 2}{sup +}, and H{sub 3}{sup +}. For all experimental conditions, the fraction of H{sub 2}{sup +} ions in the beam was about 10 ÷ 15% of the total ion beam current and varied little with ion source parameters. At the same time, the ratio of H{sup +} and H{sub 3}{sup +} depended strongly on the discharge current, particularly on its distribution in the gap between the hollow and planar cathodes. Increasing the discharge current increased the H{sup +} fraction in ion beam. The maximum fraction of H{sup +} reached 80% of the total ion beam current. Forced redistribution of the discharge current in the cathode gap for increasing the hollow cathode current could greatly increase the H{sub 3}{sup +} fraction in the beam. At optimum parameters, the fraction of H{sub 3}{sup +} ions reached 60% of the total ion beam current.

  2. Preparation and investigation of diamond-like carbon stripper foils by filtered cathodic vacuum arc

    Energy Technology Data Exchange (ETDEWEB)

    Fan, Qiwen, E-mail: fanqiwen0926@163.com [Department of Nuclear Physics, China Institute of Atomic Energy, P.O. Box 275(62), Beijing 102413 (China); Du, Yinghui; Zhang, Rong; Xu, Guoji [Department of Nuclear Physics, China Institute of Atomic Energy, P.O. Box 275(62), Beijing 102413 (China)

    2013-04-21

    Thin diamond-like carbon (DLC) stripper foils ∼5μg/cm{sup 2} in thickness were produced and evaluated as heavy-ion strippers for the Beijing HI-13 Tandem Accelerator. The DLC layers ∼4μg/cm{sup 2} in thickness were produced by the filtered cathodic vacuum arc technology onto glass slides coated with betaine–saccharose as releasing agent, which were previously covered with evaporated carbon layers ∼1μg/cm{sup 2} in thickness by the controlled ac arc-discharge method. Irradiation lifetimes of the DLC stripper foils were tested using the heavy-ion beams at the terminal of the Beijing HI-13 Tandem Accelerator, and compared with those of the standard carbon stripper foils made by the combined dc and ac arc-discharge method. The measurements indicate that the DLC stripper foils outlast the standard combined dc and ac arc-discharge carbon stripper foils by a factor of at least 13 and 4 for the {sup 197}Au{sup −} (∼9MeV, ∼1μA) and {sup 63}Cu{sup −} (∼9MeV, ∼1μA) ion beams, respectively. The structure and properties of the DLC foils deposited onto silicon substrates by the filtered cathodic vacuum arc technology were also evaluated and analyzed by scanning electron microscopy, Raman spectroscopy and X-ray photoelectron spectroscopy. The scanning electron microscopy images show that the DLC foils contain hardly droplets through the double 90° filters. The X-ray photoelectron spectrum indicates that sp{sup 3} bonds of the DLC foils exceed 70%. The integral intensity ratio of the D peak to the G peak (I{sub D}/I{sub G}) measured by the Raman spectroscopy is 0.78.

  3. Electron Emission from Ferroelectric/Antiferroelectric Cathodes Excited by Short High-Voltage Pulses

    CERN Document Server

    Benedek, G; Handerek, J; Riege, H

    1997-01-01

    Un-prepoled Lead Zirconate Titanate Lanthanum doped-PLZT ferroelectric cathodes have emitted intense current pulses under the action of a high voltage pulse of typically 8 kV/cm for PLZT of 8/65/35 composition and 25 kV/cm for PLZT of 4/95/5 composition. In the experiments described in this paper, the exciting electric field applied to the sample is directed from the rear surface towards the emitting surface. The resulting emission is due to an initial field emission from the metal of the grid deposited over the emitting surface with the consequent plasma formation and the switching of ferroelectric domains. These electrons may be emitted directly form the crystal or from the plasma. This emission requires the material in ferroelectric phase. In fact, PLZT cathodes of the 8/65/35 type, that is with high Titanium content, showing ferroelectric-paraelectric phase sequence, emit at room temperature, while PLZT cathodes of the 4/95/5 type, that is with low Titanium content, having antiferro-ferro-paraelectric pha...

  4. Stimulated Raman hyperspectral imaging based on spectral filtering of broadband fiber laser pulses.

    Science.gov (United States)

    Ozeki, Yasuyuki; Umemura, Wataru; Sumimura, Kazuhiko; Nishizawa, Norihiko; Fukui, Kiichi; Itoh, Kazuyoshi

    2012-02-01

    We demonstrate a technique of hyperspectral imaging in stimulated Raman scattering (SRS) microscopy using a tunable optical filter, whose transmission wavelength can be varied quickly by a galvanometer mirror. Experimentally, broadband Yb fiber laser pulses are synchronized with picosecond Ti:sapphire pulses, and then spectrally filtered out by the filter. After amplification by fiber amplifiers, we obtain narrowband pulses with a spectral width of 225 cm(-1). By using these pulses, we accomplish SRS imaging of polymer beads with spectral information.

  5. Nanodiamond embedded ta-C composite film by pulsed filtered vacuum arc deposition from a single target

    Science.gov (United States)

    Iyer, Ajai; Etula, Jarkko; Ge, Yanling; Liu, Xuwen; Koskinen, Jari

    2016-11-01

    Detonation Nanodiamonds (DNDs) are known to have sp3 core, sp2 shell, small size (few nm) and are gaining importance as multi-functional nanoparticles. Diverse methods have been used to form composites, containing detonation nanodiamonds (DNDs) embedded in conductive and dielectric matrices for various applications. Here we show a method, wherein DND-ta-C composite film, consisting of DNDs embedded in ta-C matrix have been co-deposited from the same cathode by pulsed filtered cathodic vacuum arc method. Transmission Electron Microscope analysis of these films revel the presence of DNDs embedded in the matrix of amorphous carbon. Raman spectroscopy indicates that the presence of DNDs does not adversely affect the sp3 content of DND-ta-C composite film compared to ta-C film of same thickness. Nanoindentation and nanowear tests indicate that DND-ta-C composite films possess improved mechanical properties in comparison to ta-C films of similar thickness.

  6. Device quality ZnO grown using a Filtered Cathodic Vacuum Arc

    Energy Technology Data Exchange (ETDEWEB)

    Elzwawi, Salim, E-mail: salim.elzwawi@pg.canterbury.ac.nz [Department of Electrical and Computer Engineering, University of Canterbury, Private Bag 4800, Christchurch 8140, Canterbury (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Kim, Hyung Suk, E-mail: david.kim@pg.canterbury.ac.nz [Department of Electrical and Computer Engineering, University of Canterbury, Private Bag 4800, Christchurch 8140, Canterbury (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Heinhold, Robert, E-mail: robert.heinhold@pg.canterbury.ac.nz [Department of Electrical and Computer Engineering, University of Canterbury, Private Bag 4800, Christchurch 8140, Canterbury (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Lynam, Max, E-mail: mfl38@uclive.ac.nz [Department of Electrical and Computer Engineering, University of Canterbury, Private Bag 4800, Christchurch 8140, Canterbury (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Turner, Gary, E-mail: gary.turner@canterbury.ac.nz [Department of Electrical and Computer Engineering, University of Canterbury, Private Bag 4800, Christchurch 8140, Canterbury (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Partridge, Jim G., E-mail: jim.partridge@canterbury.ac.nz [Department of Electrical and Computer Engineering, University of Canterbury, Private Bag 4800, Christchurch 8140, Canterbury (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); McCulloch, Dougal G., E-mail: dougal.mcculloch@rmit.edu.au [Applied Sciences, RMIT University, GPO Box 2476 V, Melbourne, VIC 3001 (Australia)

    2012-08-01

    In this paper we report on the structural, electrical and optical characteristics of unintentionally doped ZnO films grown on a-plane sapphire substrates using the Filtered Cathodic Vacuum Arc (FCVA) technique. The resulting films showed considerable promise for device applications with properties including high transparency, moderate intrinsic carrier concentrations (10{sup 17}-10{sup 19} cm{sup -3}), electron mobilities up to 30 cm{sup 2}/Vs, low surface roughness (typically <2% of film thickness) and well-structured photoluminescence. Post-annealing in oxygen at temperatures up to 800 Degree-Sign C produced significant improvements in the properties of these films. Silver oxide Schottky diodes fabricated on FCVA ZnO showed ideality factors as low as 1.20 and good sensitivity to ultraviolet light.

  7. Ampère-Class Pulsed Field Emission from Carbon-Nanotube Cathodes in a Radiofrequency Resonator

    Energy Technology Data Exchange (ETDEWEB)

    Mihalcea, D. [Northern Illinois U.; Faillace, L. [RadiaBeam Tech.; Hartzell, J. [RadiaBeam Tech.; Panuganti, H. [Northern Illinois U.; Boucher, S. M. [RadiaBeam Tech.; Murokh, A. [RadiaBeam Tech.; Piot, P. [Fermilab; Thangaraj, J. C.T. [Fermilab

    2014-12-01

    Pulsed field emission from cold carbon-nanotube cathodes placed in a radiofrequency resonant cavity was observed. The cathodes were located on the backplate of a conventional $1+\\frac{1}{2}$-cell resonant cavity operating at 1.3-GHz and resulted in the production of bunch train with maximum average current close to 0.7 Amp\\`ere. The measured Fowler-Nordheim characteristic, transverse emittance, and pulse duration are presented and, when possible, compared to numerical simulations. The implications of our results to high-average-current electron sources are briefly discussed.

  8. The multilayered structure of ultrathin amorphous carbon films synthesized by filtered cathodic vacuum arc deposition

    KAUST Repository

    Wang, Na

    2013-08-01

    The structure of ultrathin amorphous carbon (a-C) films synthesized by filtered cathodic vacuum arc (FCVA) deposition was investigated by high-resolution transmission electron microscopy, electron energy loss spectroscopy, and x-ray photoelectron spectroscopy. Results of the plasmon excitation energy shift and through-thickness elemental concentration show a multilayered a-C film structure comprising an interface layer consisting of C, Si, and, possibly, SiC, a buffer layer with continuously increasing sp 3 fraction, a relatively thicker layer (bulk film) of constant sp 3 content, and an ultrathin surface layer rich in sp 2 hybridization. A detailed study of the C K-edge spectrum indicates that the buffer layer between the interface layer and the bulk film is due to the partial backscattering of C+ ions interacting with the heavy atoms of the silicon substrate. The results of this study provide insight into the minimum thickness of a-C films deposited by FCVA under optimum substrate bias conditions. Copyright © 2013 Materials Research Society.

  9. Microstructure Changes of Ti-Al-C Films Deposited by Filtered Cathodic Vacuum Arc

    Directory of Open Access Journals (Sweden)

    Xianjuan Pang

    2014-01-01

    Full Text Available Nanocomposite Ti-Al-C films were deposited by filtered cathodic vacuum arc (FCVA at different CH4 flows. The deposited films were characterized in terms of elemental and phase compositions, chemical bonds, and texture as a function of CH4 flow rate by XRD, XPS, HRTEM, Raman spectroscopy, and IR spectroscopy. The results show that the TiC grain size decreases from 4.2 to 2.9 nm as the CH4 flow rate increases from 30 to 80 sccm. The analysis of XPS, HRTEM, and Raman spectroscopy shows that the microstructure of deposited films turns from a TiC dominant TiC-C film to a carbon network dominant TiAl-doped a-C film structure as the CH4 flow increases from 30 sccm to 80 sccm. IR spectroscopy shows that most of the hydrogen atoms in the deposited films are bonded to the sp3-hybridized C atoms. All the composition and microstructure change can be explained by considering the plasma conditions and the effect of CH4 flow.

  10. Optimal Linear Filters for Pulse Height Measurements in the Presence of Noise

    Energy Technology Data Exchange (ETDEWEB)

    Nygaard, K.

    1966-07-15

    For measurements of nuclear pulse height spectra a linear filter is used between the pulse amplifier and the pulse height recorder so as to improve the signal/noise ratio. The problem of finding the optimal filter is investigated with emphasis on technical realizability. The maximum available signal/noise ratio is theoretically calculated on the basis of all the information which can be found in the output of the pulse amplifier, and on an assumed a priori knowledge of the pulse time of arrival. It is then shown that the maximum available signal/noise ratio can be obtained with practical measurements without any a priori knowledge of pulse time of arrival, and a general description of the optimal linear filter is given. The solution is unique, technically realizable, and based solely on data (noise power spectrum and pulse shape) which can be measured at the output terminals of the pulse amplifier used.

  11. Determination of selenium in natural waters by adsorptive differential pulse cathodic stripping voltammetry.

    Science.gov (United States)

    Ashournia, Mehdi; Aliakbar, Alireza

    2009-08-30

    In this work bovine albumin was used innovatively as a medium for adsorptive accumulation of Se-I(2) on thin mercury film electrode. Se-I(2) was formed by reaction between Se(IV) and iodide in HCl media. The adsorbed Se-I(2) was stripped in 0.05 M HCl by differential pulse cathodic potential scan. The proposed method was successfully applied to analysis of Se(IV) and Se(VI) in natural waters sampled from some lagoons south of Caspian Sea. The optimum reaction conditions and other analytical parameters and influence of cations and anions were studied. The detection limit was 0.37 ng mL(-1). The obtained results were compared with the results of DPCSV after electrochemical preconcentration, HG-AAS and ICP-AES.

  12. Impact of Spectral Filter on Phase Modulation Pulse in Fiber Front End System

    Institute of Scientific and Technical Information of China (English)

    LI Jing; JING Feng; WANG Jian-Jun; XU Dang-Peng; LIN Hong-Huan; GENG Yuan-Chao; LI Ming-Zhong; DENG Ying; ZHU Na; ZHANG Rui

    2011-01-01

    The transmission characteristics of phase modulation pulse transmitted through the filter in the power amplifier are investigated theoretically and experimentally. The narrow bandpass filter can induce large temporal modula-tion depth for the phase modulation pulse and induce double amplitude modulation(AM)if the frequency shift is lower than half bandwidth of the signal spectrum. We should choose a wider bandwidth filter to minimize the impact of the filter on the output pulse and suppress the amplified spontaneous emission(ASE) for the power fiber amplifier. These results are of benefit to the design of the fiber front end system.

  13. Influence of optical filters on pulse circulation in fiber rings with a frequency shifter and EDFA.

    Science.gov (United States)

    Takano, Katsumi; Nakagawa, Kiyoshi; Ito, Hiromasa

    2006-10-30

    Optical fiber ring circuits constructed with frequency shifters and EDFAs are applicable to pulsed lightwave frequency sweepers, wavelength converters, and optical packet buffers. The salient criterion for those applications is how many times the optical pulse can circle the ring. Optical band-pass filters in the ring can serve an important role for pulse circulation because the filter determines the gain bandwidth at every circulation under the condition of signal wavelength shift. This paper clarifies the effects of optical filter response on pulse circulation in the ring through numerical simulation of the EDFA dynamic model, considering the gain spectrum.

  14. Determination of Selenium in infant formula by differential pulse cathodic stripping voltammetry

    Directory of Open Access Journals (Sweden)

    "Oveisi MR

    2002-07-01

    Full Text Available Selenium as a nonmetallic chemical element has received high attention of biologists because of its dual role as an essential trace nutrient and a toxic element. This interest has created a need for reliable analytical methods for determination of selenium. In this investigation determination of selenium by differential pulse cathodic stripping voltammetry and the influence of various parameters such as deposition potentials, deposition time. Cu concentration pH, etc. on selenium peak in voltammogram are described. Determination of selenium was accomplished in mixture of acetic acid, hydrochloric acid and sodium chloride buffer (pH=1 with a scan rate of 60 mv/s and a pulse height of 100 my by hanging mercury drop electrode (HMDE as working electrode. The solution was stirred during pre-electrolysis at - 350 mv (vs SCE for 30 s and the potential was scanned between - 350 mv and - 800 mv. The determination limit of the method was 0.005 mg/kg for the sample. The calibration curves were linear in the range of 0-30 μg/L (R2=0.996, p<0.001. Repeatability of the method at concentrations of 30 and 0.5 μg/L were 2.5 and 10.5% respectively.

  15. New ion-assisted filtered cathodic arc deposition (IFCAD) technology for producing advanced thin films on temperature-sensitive substrates

    Science.gov (United States)

    Fulton, Michael L.

    1999-10-01

    An innovative Ion-Assisted Filtered Cathodic Arc Deposition (IFCAD) system has been developed for low temperature production of thin-film coatings. The IFCAD system employs electro-magnetic and mechanical filtering techniques to remove unwanted macroparticles and neutral atoms from the plasma stream. Therefore, only ions within a defined energy range arrive at the substrate surface, depositing thin-films with excellent mechanical and optical properties. Ion- Assisted-Deposition is coupled with Filtered Cathodic Arc technology to enhance and modify the arc deposited thin- films. Using an advanced computer controlled plasma beam scanning system, high quality, large area, uniform IFCAD multi-layer film structures are attained. Amorphous Diamond- Like-Carbon films (up to 85% sp3 bonded carbon; and micro- hardness greater than 50 GPa) have been deposited in multi- layer thin-film combinations with other IFCAD source materials (such as: Al2O3) for optical and tribological applications. Rutile TiO2 (refractive index of 2.8 at 500 nm) has been deposited with this technology for advanced optical filter applications. The new IFCAD technology has been included in development programs, such as: plastic and glass lens coatings for optical systems; wear resistant coatings on various metal substrates, ultra smooth, durable, surface hydrophobic coatings for aircraft windows; EUV coatings for space instrumentation; transparent conductive coatings; and UV protective coatings for solar cell concentrator plastic Fresnel lens elements for space power.

  16. Cathodoluminescence of Cr-doped diamond-like carbon film by filtered cathodic vacuum arc plasma

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Meng-Wen; Jao, Jui-Yun [Department of Materials Science and Engineering, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 402, Taiwan (China); Lin, Chun-Chun; Hsieh, Wei-Jen; Yang, Yu-Hsiang [Department of Materials Science and Engineering, National Tsing Hua University, 101, Sec. 2, Kuang-Fu Road, Hsinchu 300, Taiwan (China); Cheng, Li-Shin; Shieu, F.S. [Department of Materials Science and Engineering, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 402, Taiwan (China); Shih, Han C., E-mail: hcshih@mx.nthu.edu.tw [Department of Materials Science and Engineering, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 402, Taiwan (China); Department of Materials Science and Engineering, National Tsing Hua University, 101, Sec. 2, Kuang-Fu Road, Hsinchu 300, Taiwan (China); Institute of Materials Science and Nanotechnology, Chinese Culture University, 55 Hwa Kang Road, Yang Ming Shan, Taipei 111, Taiwan (China)

    2012-11-15

    Highlights: Black-Right-Pointing-Pointer The formation of the DLC:Cr films dependent on the flow rates of C{sub 2}H{sub 2}/Ar have been achieved in our FCVA plasma. Black-Right-Pointing-Pointer The amorphous DLC:Cr have high sp{sup 2} content can be completely converted to nanocrystalline Cr{sub 3}C{sub 2}. Black-Right-Pointing-Pointer The effect of doping with Cr is apparently to change the band structure of the DLC and its consequent cathodoluminescence property. - Abstract: Cr doped diamond-like carbon (DLC:Cr) film was synthesized in various flow rates of C{sub 2}H{sub 2}/Ar under a substrate voltage of -50 V at 500 Degree-Sign C by a filtered cathodic vacuum arc plasma. This work has found that the structure of the films was correlated to the flow rate of C{sub 2}H{sub 2}/Ar but the luminescence properties are similar. The cathodoluminescence spectra of DLC:Cr films obtained at 1.9-2.4 eV verifies that the luminescence from the films is in the visible region. The incorporation of Cr into the carbon network results in red emission shifted to 1.99 eV and the orange emission (2.03 eV) also appeared due to the transitions between chromium-related electron levels and {sigma}* states. The peak at 2.10 eV may result from the defects of the structures in DLC:Cr films.

  17. Growth of single and bilayer graphene by filtered cathodic vacuum arc technique

    Energy Technology Data Exchange (ETDEWEB)

    Kesarwani, A. K.; Panwar, O. S., E-mail: ospanwar@mail.nplindia.ernet.in; Bisht, Atul [Polymorphic Carbon Thin Films Group, Physics of Energy Harvesting Division, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi 110012, India and Academy of Scientific and Innovative Research (AcSIR), CSIR Campus, New Delhi 110012 (India); Dhakate, S. R. [Physics and Engineering of Carbon Materials, Division of Materials Physics and Engineering, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi 110012, India and Academy of Scientific and Innovative Research (AcSIR), CSIR Campus, New Delhi 110012 (India); Rakshit, R. K. [Quantum Phenomena and Applications Group, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi 110012, India and Academy of Scientific and Innovative Research (AcSIR), CSIR Campus, New Delhi 110012 (India); Singh, V. N. [Electron and Ion Microscopy, Sophisticated and Analytical Instruments, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi 110012, India and Academy of Scientific and Innovative Research (AcSIR), CSIR Campus, New Delhi 110012 (India); Kumar, Ashish [Polymorphic Carbon Thin Films Group, Physics of Energy Harvesting Division, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi 110012 (India)

    2016-03-15

    The authors present a viable process to grow the high quality graphene films with control over number of layers by the filtered cathodic vacuum arc (FCVA) technique. In the FCVA process, the different carbon concentrations can be controlled by precisely tuning the arc time (1–4 s). The arc generated carbon was deposited on the nickel catalyst at 800 °C, annealed for 10 min, and cooled down to room temperature in the presence of hydrogen gas, resulting in the graphene films with control over number of layers. Prior to arcing, hydrogen etching of nickel was carried out to clean the surface of the substrate. A growth model to prepare the high quality graphene has also been proposed. The as-grown graphene films were transferred to different substrates and are characterized by Raman spectroscopy, optical microscopy, high resolution transmission electron microscopy, and atomic force microscopy to determine the number of layers present in these films. Raman spectra of the prepared graphene films exhibit change in the G peak position from 1582.4 to 1578.1 cm{sup −1}, two-dimensional (2D) peak shifts from 2688.5 to 2703.8 cm{sup −1}, the value of I{sub 2D}/I{sub G} increased from 0.38 to 3.82, and the full width at half maxima of 2D peak changed from 41 to 70 cm{sup −1}, for different layers of graphene films. The high resolution transmission electron microscopy image revealed that the graphene films prepared for 1 and 2 s arc times have single and bi- or trilayered structures, respectively.

  18. Influence of selected fixed parameters on pulse-jet fabric filter operation

    Science.gov (United States)

    Hindy, K. T.

    The effect of (a) fixing the time interval between cleaning pulses or (b) fixing the maximum pressure drop at which cleaning is started, on the performance of the fabric filter was investigated. A maximum pressure drop value of 2500 Pa: (a) minimized the effect of the filter medium resistance; (b) reduced the energy consumption by the filter; (c) minimized the dust emission from the fabric filter to the surrounding atmosphere.

  19. Cathodic arcs

    OpenAIRE

    Anders, Andre

    2003-01-01

    Cathodic arc plasma deposition has become the technology of choice for hard, wear and corrosion resistant coatings for a variety of applications. The history, basic physics of cathodic arc operation, the infamous macroparticle problem and common filter solutions, and emerging high-tech applications are briefly reviewed. Cathodic arc plasmas stand out due to their high degree of ionization, with important consequences for film nucleation, growth, and efficient utilization of substrate bia...

  20. Experimental study and modeling of the deuterium releasing quantity in a pulsed vacuum arc discharge with a metal deuteride cathode

    Science.gov (United States)

    Liu, Fei-Xiang; Long, Ji-Dong; Zheng, Le; Dong, Pan; Li, Chen; Chen, Wei

    2017-04-01

    The pulsed vacuum arc discharge using a metal deuteride cathode is widely applied as a deuterium ion source, where the upper limit of the deuterium ion yield is largely determined by the deuterium releasing quantity (DRQ) from the cathode. This work aims to measure the DRQ at various discharge conditions, and meanwhile develop a simple thermoelectric model to evaluate the deuterium liberation from different sources, such as the crater vicinity during the arc power-on phase and the hot crater in the afterglow. The calculated DRQ are in accordance with the experimental results obtained by measuring the D2 pressure evolution in the early afterglow using a quadrupole mass spectrometer. Furthermore, the model reveals that at low arc current (<10 A), the DRQ orginates dominantly from the crater vicinity, leading to a low conversion efficiency of the released deuterium to ions and a high D:Ti elemental ratio in the released cathode vapor.

  1. Array of virtual Frisch-grid CZT detectors with common cathode readout and pulse-height correction

    Energy Technology Data Exchange (ETDEWEB)

    Bolotnikov, A.E.; Camarda, G.S.; Cui, Y.; Egarievwe, E.U.; Fochuk, P.M.; Fuerstnau, M.; Gul, R.; Hossain, A.; Jones, F.; Kim, K.; Kopach, O.V.; Taggart, R.; Yang, G.; Ye, Z.; Xu, L.; and James, R.B.

    2010-08-01

    We present our new results from testing 15-mm-long virtual Frisch-grid CdZnTe detectors with a common-cathode readout for correcting pulse-height distortions. The array employs parallelepiped-shaped CdZnTe (CZT) detectors of a large geometrical aspect ratio, with two planar contacts on the top and bottom surfaces (anode and cathode) and an additional shielding electrode on the crystal's sides to create the virtual Frisch-grid effect. We optimized the geometry of the device and improved its spectral response. We found that reducing to 5 mm the length of the shielding electrode placed next to the anode had no adverse effects on the device's performance. At the same time, this allowed corrections for electron loss by reading the cathode signals to obtain depth information.

  2. Analysis of Beaulieu Pulse Shaping Family Based FIR Filter for WCDMA

    CERN Document Server

    Kang, A S

    2010-01-01

    The analysis and simulation of transmit and receive pulse shaping filter is an important aspect of digital wireless communication since it has a direct effect on error probabilities. Pulse shaping for wireless communication over time as well as frequency selective channels is the need of hour for 3G and 4G systems. The pulse shaping filter is a useful means to shape the signal spectrum and avoid interferences. Basically digital filters are used to modify the characteristics of signal in time and frequency domain and have been recognized as primary digital signal processing operations.

  3. Spatial mask filtering algorithm for partial discharge pulse extraction of large generators

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A spatial mask filter algorithm (SMF) for partial discharge (PD) pulse extraction is proposed in this then direct multiplication of coefficients at two adjacent scales is used to detect singularity points of the signal tain the last spatial mask filter. By multiplication of wavelet coefficients with the final mask filter and wavelet reconstruction process, partial discharge pulses are extracted. The results of digital simulation and practical experiment show that this method is superior to traditional wavelet shrinkage method (TWS). This algorithm not only can increase the signal to noise ratio (SNR), but also can preserve the energy and pulse amplitude.

  4. Nonlinear pulse compression of picosecond parabolic-like pulses synthesized with a long period fiber grating filter.

    Science.gov (United States)

    Krcmarík, David; Slavík, Radan; Park, Yongwoo; Azaña, José

    2009-04-27

    tract: We demonstrate high quality pulse compression at high repetition rates by use of spectral broadening of short parabolic-like pulses in a normally-dispersive highly nonlinear fiber (HNLF) followed by linear dispersion compensation with a conventional SMF-28 fiber. The key contribution of this work is on the use of a simple and efficient long-period fiber grating (LPFG) filter for synthesizing the desired parabolic-like pulses from sech(2)-like input optical pulses; this all-fiber low-loss filter enables reducing significantly the required input pulse power as compared with the use of previous all-fiber pulse re-shaping solutions (e.g. fiber Bragg gratings). A detailed numerical analysis has been performed in order to optimize the system's performance, including investigation of the optimal initial pulse shape to be launched into the HNLF fiber. We found that the pulse shape launched into the HNLF is critically important for suppressing the undesired wave breaking in the nonlinear spectral broadening process. The optimal shape is found to be independent on the parameters of normally dispersive HNLFs. In our experiments, 1.5-ps pulses emitted by a 10-GHz mode-locked laser are first reshaped into 3.2-ps parabolic-like pulses using our LPFG-based pulse reshaper. Flat spectrum broadening of the amplified initial parabolic-like pulses has been generated using propagation through a commercially-available HNLF. Pulses of 260 fs duration with satellite peak and pedestal suppression greater than 17 dB have been obtained after the linear dispersion compensation fiber. The generated pulses exhibit a 20-nm wide supercontinuum energy spectrum that has almost a square-like spectral profile with >85% of the pulse energy contained in its FWHM spectral bandwidth.

  5. Pulse combustion reactor as a fast and scalable synthetic method for preparation of Li-ion cathode materials

    Science.gov (United States)

    Križan, Gregor; Križan, Janez; Dominko, Robert; Gaberšček, Miran

    2017-09-01

    In this work a novel pulse combustion reactor method for preparation of Li-ion cathode materials is introduced. Its advantages and potential challenges are demonstrated on two widely studied cathode materials, LiFePO4/C and Li-rich NMC. By exploiting the nature of efficiency of pulse combustion we have successfully established a slightly reductive or oxidative environment necessary for synthesis. As a whole, the proposed method is fast, environmentally friendly and easy to scale. An important advantage of the proposed method is that it preferentially yields small-sized powders (in the nanometric range) at a fast production rate of 2 s. A potential disadvantage is the relatively high degree of disorder of synthesized active material which however can be removed using a post-annealing step. This additional step allows a further tuning of materials morphology as shown and commented in some detail.

  6. Determination of total gaseous selenium in atmosphere by honeycomb denuder/differential pulse cathodic stripping voltammetry.

    Science.gov (United States)

    Zhang, Bicheng; Xu, Hui; Yu, Jimmy C

    2002-05-16

    A new analytical method has been developed for the determination of total gaseous selenium in the atmosphere by honeycomb denuder collection followed by differential pulse cathodic stripping voltammetry (DPCSV) measurement. Gaseous selenium was collected in a denuder coating solution containing 2% HNO(3) and 2% glycerine. The soluble product, selenious acid, was then extracted by water for DPCSV analysis. The collection efficiency for gaseous selenium was 99.1% at a flow rate of 1 l min(-1) for 3 h. Excellent linearity in DPCSV was maintained up to Se concentration of 40 ng ml(-1). This was equivalent to a working concentration of 220 ng m(-3) of selenium in the atmosphere. A precision of 1.26% RSD (n=5) for 5 ng Se was obtained, and the detection limit (3sigma) and the quantitative determination limit were estimated to be 0.96 and 3.19 ng m(-3). The average recovery of selenium in three standard samples prepared by independent digestion of NIST SRM 1648 (Urban Particulate Matter) using our analytical system was 99.0%. The total content of gaseous selenium in the atmosphere of our laboratories was 3.2-4.4 ng m(-3).

  7. Topology optimization of pulse shaping filters using the Hilbert transform envelope extraction

    DEFF Research Database (Denmark)

    Lazarov, Boyan Stefanov; Matzen, René; Elesin, Yuriy

    2011-01-01

    Time domain topology optimization is applied to design pulse shaping filters. The objective function depends on the pulse envelope, which is extracted by utilizing the Hilbert transform. The gradients with respect to the topology optimization variables are derived, and the optimization methodology...

  8. Pulse Compression by Filamentation in Argon with an Acoustic Optical Programmable Dispersive Filter for Predispersion Compensation

    Institute of Scientific and Technical Information of China (English)

    CHEN Xiao-Wei; JIANG Yong-Liang; LENG Yu-Xin; LIU Jun; GE Xiao-Chun; LI Ru-Xin; XU Zhi-Zhan

    2006-01-01

    @@ We have experimentally demonstrated pulses 0.4 mJ in duration smaller than 12 fs with an excellent spatial beam profile by self-guided propagation in argon. The original 52fs pulses from the chirped pulsed amplification laser system are first precompressed to 32 fs by inserting an acoustic optical programmable dispersive filter instrument into the laser system for spectrum reshaping and dispersion compensation, and the pulse spectrum is subsequently broadened by filamentation in an argon cell. By using chirped mirrors for post-dispersion compensation, the pulses are successfully compressed to smaller than 12fs.

  9. Pulse cleaning flow models and numerical computation of candle ceramic filters

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Analytical and numerical computed models are developed for reverse pulse cleaning system of candle ceramic filters. A standard turbulent model is demonstrated suitably to the designing computation of reverse pulse cleaning system from the experimental and onedimensional computational result. The computed results can be used to guide the designing of reverse pulse cleaning system, which is optimum Venturi geometry. From the computed results, the general conclusions and the designing methods are obtained.

  10. Design of Excitatory Signal and Matched Filter for Compressed Pulsed Radar

    Directory of Open Access Journals (Sweden)

    Argel Gonzalez Padilla

    2013-11-01

    Full Text Available In this paper is presented pulse compression technique in radar, focusing on Linear Frequency Modulation (LFM. Matched Filter characteristics are the elements considered for pulse compression, algebraic operations are derived to avoid the signal phase effect received by detection capacity. A hardware system for pulse compression in language description hardware is implemented. The product obtained is a first step in radar techniques to improve resolution capacity.

  11. Pulse shaping in mode-locked fiber lasers by in-cavity spectral filter.

    Science.gov (United States)

    Boscolo, Sonia; Finot, Christophe; Karakuzu, Huseyin; Petropoulos, Periklis

    2014-02-01

    We numerically show the possibility of pulse shaping in a passively mode-locked fiber laser by inclusion of a spectral filter into the laser cavity. Depending on the amplitude transfer function of the filter, we are able to achieve various regimes of advanced temporal waveform generation, including ones featuring bright and dark parabolic-, flat-top-, triangular- and saw-tooth-profiled pulses. The results demonstrate the strong potential of an in-cavity spectral pulse shaper for controlling the dynamics of mode-locked fiber lasers.

  12. Numerical and experimental study of pulse-jet cleaning in fabric filters

    DEFF Research Database (Denmark)

    O. Andersen, B.; Nielsen, N. F.; Walther, J. H.

    2016-01-01

    for many years by experimental investigation and to a limited extent by Computational Fluid Dynamics (CFD). The majority of the studies have focused on high-pressure cleaning systems, and the CFD models presented are so far two-dimensional (2D). In the work presented here, pulse-jet cleaning of low......Pulse-jet cleaning and understanding of the complex physics are essential when designing fabric filters used for air pollution control. Today, low-pressure cleaning is of particular interest due to demand for reduced compressed air consumption. Pulse-jet cleaned fabric filters have been studied......-pressure fabric filters (2 bar) is studied using a full three-dimensional (3D) CFD model. Experimental results obtained in a pilot-scale test filter with 28 bags, in length of 10 m and in general full-scale dimensions of the cleaning system are used to verify the reliability of the present CFD model...

  13. Nonparametric Interference Suppression Using Cyclic Wiener Filtering: Pulse Shape Design and Performance Evaluation

    Directory of Open Access Journals (Sweden)

    Anass Benjebbour

    2008-02-01

    Full Text Available In the future, there will be a growing need for more flexible but efficient utilization of radio resources. Increased flexibility in radio transmission, however, yields a higher likelihood of interference owing to limited coordination among users. In this paper, we address the problem of flexible spectrum sharing where a wideband single carrier modulated signal is spectrally overlapped by unknown narrowband interference (NBI and where a cyclic Wiener filter is utilized for nonparametric NBI suppression at the receiver. The pulse shape design for the wideband signal is investigated to improve the NBI suppression capability of cyclic Wiener filtering. Specifically, two pulse shaping schemes, which outperform existing raised cosine pulse shaping schemes even for the same amount of excess bandwidth, are proposed. Based on computer simulation, the interference suppression capability of cyclic Wiener filtering is evaluated for both the proposed and existing pulse shaping schemes under several interference conditions and over both AWGN and Rayleigh fading channels.

  14. Nonparametric Interference Suppression Using Cyclic Wiener Filtering: Pulse Shape Design and Performance Evaluation

    Directory of Open Access Journals (Sweden)

    Benjebbour Anass

    2008-01-01

    Full Text Available Abstract In the future, there will be a growing need for more flexible but efficient utilization of radio resources. Increased flexibility in radio transmission, however, yields a higher likelihood of interference owing to limited coordination among users. In this paper, we address the problem of flexible spectrum sharing where a wideband single carrier modulated signal is spectrally overlapped by unknown narrowband interference (NBI and where a cyclic Wiener filter is utilized for nonparametric NBI suppression at the receiver. The pulse shape design for the wideband signal is investigated to improve the NBI suppression capability of cyclic Wiener filtering. Specifically, two pulse shaping schemes, which outperform existing raised cosine pulse shaping schemes even for the same amount of excess bandwidth, are proposed. Based on computer simulation, the interference suppression capability of cyclic Wiener filtering is evaluated for both the proposed and existing pulse shaping schemes under several interference conditions and over both AWGN and Rayleigh fading channels.

  15. Nanocrystallization of LiCoO2 Cathodes for Thin Film Batteries Utilizing Pulse Thermal Processing

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-04-01

    This factsheet describes a study whose focus is on the nanocrystallization of the LiCoO2 cathode thin films on polyimide substrates and evaluate the microstructural evolution and resistance as a function of PTP processing conditions.

  16. Filtering images contaminated with pep and salt type noise with pulse-coupled neural networks

    Institute of Scientific and Technical Information of China (English)

    ZHANG Junying; LU Zhijun; SHI Lin; DONG Jiyang; SHI Meihong

    2005-01-01

    Pulse coupled neural network (PCNN) has a specific feature that the fire of one neuron can capture its adjacent neurons to fire due to their spatial proximity and intensity similarity. In this paper, it is indicated that this feature itself is a very good mechanism for image filtering when the image is damaged with pep and salt (PAS) type noise. An adaptive filtering method, in which the noisy pixels are first located and then filtered based on the output of the PCNN, is presented. The threshold function of a neuron in the PCNN is designed when it is used for filtering random PAS and extreme PAS noise contaminated image respectively. The filtered image has no distortion for noisy pixels and only less mistiness for non-noisy pixels, compared with the conventional window-based filtering method. Excellent experimental results show great effectiveness and efficiency of the proposed method, especially for heavy-noise contaminated images.

  17. Cathodic arcs

    Energy Technology Data Exchange (ETDEWEB)

    Anders, Andre

    2003-10-29

    Cathodic arc plasma deposition has become the technology of choice for hard, wear and corrosion resistant coatings for a variety of applications. The history, basic physics of cathodic arc operation, the infamous macroparticle problem and common filter solutions, and emerging high-tech applications are briefly reviewed. Cathodic arc plasmas standout due to their high degree of ionization, with important consequences for film nucleation, growth, and efficient utilization of substrate bias. Industrial processes often use cathodic arc plasma in reactive mode. In contrast, the science of arcs has focused on the case of vacuum arcs. Future research directions include closing the knowledge gap for reactive mode, large area coating, linear sources and filters, metal plasma immersion process, with application in high-tech and biomedical fields.

  18. Achieving high mobility ZnO : Al at very high growth rates by dc filtered cathodic arc deposition

    Energy Technology Data Exchange (ETDEWEB)

    Mendelsberg, R J; Lim, S H N; Wallig, J; Anders, A [Lawrence Berkeley National Laboratory, Plasma Applications Group, Berkeley, CA (United States); Zhu, Y K [Harbin Institute of Technology, Harbin (China); Milliron, D J, E-mail: aanders@lbl.gov [Lawrence Berkeley National Laboratory, Molecular Foundry, Berkeley, CA (United States)

    2011-06-15

    Achieving a high growth rate is paramount for making large-area transparent conducting oxide coatings at a low cost. Unfortunately, the quality of thin films grown by most techniques degrades as the growth rate increases. Filtered dc cathodic arc is a lesser known technique which produces a stream of highly ionized plasma, in stark contrast to the neutral atoms produced by standard sputter sources. Ions bring a large amount of potential energy to the growing surface which is in the form of heat, not momentum. By minimizing the distance from cathode to substrate, the high ion flux gives a very high effective growth temperature near the film surface without causing damage from bombardment. The high surface temperature is a direct consequence of the high growth rate and allows for high-quality crystal growth. Using this technique, 500-1300 nm thick and highly transparent ZnO : Al films were grown on glass at rates exceeding 250 nm min{sup -1} while maintaining resistivity below 5 x 10{sup -4} {Omega} cm with electron mobility as high as 60 cm{sup 2} V{sup -1} s{sup -1}. (fast track communication)

  19. The effect of substrate bias on titanium carbide/amorphous carbon nanocomposite films deposited by filtered cathodic vacuum arc

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xu, E-mail: zhangxu@bnu.edu.cn [Key Laboratory of Beam Technology and Material Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University (China); Liang, Hong [Key Laboratory of Beam Technology and Material Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University (China); Wu, Zhenglong [Analytical and Testing Center, Beijing Normal University (China); Wu, Xiangying; Zhang, Huixing [Key Laboratory of Beam Technology and Material Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University (China)

    2013-07-15

    The titanium carbide/amorphous carbon nanocomposite films have been deposited on silicon substrate by filtered cathodic vacuum arc (FCVA) technology, the effects of substrate bias on composition, structures and mechanical properties of the films are studied by scanning electron spectroscopy, X-ray diffraction and X-ray photoelectron spectroscopy and nano-indentation. The results show that the Ti content, deposition rate and hardness at first increase and then decrease with increasing the substrate bias. Maximum hardness of the titanium carbide/amorphous carbon nanocomposite film is 51 Gpa prepared at −400 V. The hardness enhancement may be attributed to the compressive stress and the fraction of crystalline TiC phase due to ion bombardment.

  20. Particle-in-cell simulation of electron trajectories and irradiation uniformity in an annular cathode high current pulsed electron beam source

    Science.gov (United States)

    Jiang, Wei; Wang, Langping; Zhou, Guangxue; Wang, Xiaofeng

    2017-02-01

    In order to study electron trajectories in an annular cathode high current pulsed electron beam (HCPEB) source based on carbon fiber bunches, the transmission process of electrons emitted from the annular cathode was simulated using a particle-in-cell model with Monte Carlo collisions (PIC-MCC). The simulation results show that the intense flow of the electrons emitted from the annular cathode are expanded during the transmission process, and the uniformity of the electron distribution is improved in the transportation process. The irradiation current decreases with the irradiation distance and the pressure, and increases with the negative voltage. In addition, when the irradiation distance and the cathode voltage are larger than 40 mm and -15 kV, respectively, a uniform irradiation current distribution along the circumference of the anode can be obtained. The simulation results show that good irradiation uniformity of circular components can be achieved by this annular cathode HCPEB source.

  1. Differential pulse and square-wave cathodic stripping voltammetry of xanthine and xanthosine at a mercury electrode.

    Science.gov (United States)

    Temerk, Y M; Kamal, M M; Ahmed, G A W; Ibrahim, H S M

    2003-08-01

    The surface activity of xanthine (Xan) and xanthosine (Xano) at a hanging mercury drop electrode (HMDE) was studied using out-of-phase ac and cyclic dc voltammetry. The results show that Xan and Xano were strongly adsorbed and chemically interacted with the charged mercury surface, which is the prerequisite step for applying the cathodic adsorptive stripping voltammetric determination of such biologically important compounds. Differential pulse cathodic adsorptive stripping voltammetry (DPCASV) and square-wave cathodic adsorptive stripping voltammetry (SWCASV) were applied for the ultratrace determination of Xan and Xano compounds. Moreover, a rapid and sensitive controlled adsorptive accumulation of Cu(II) complexes of both compounds provided the basis of a direct stripping voltammetric determination of such compounds to submicromolar and nanomolar levels. Operational and solution conditions for the quantitative ultratrace determination of Xan and Xano were optimized in absence and presence of Cu(II). The calibration curve data were subjected to least-squares refinements. The effects of several types of inorganic and organic interfering species on the determination of Xan or Xano were considered.

  2. Optimal Linear Filters. 2. Pulse Time Measurements in the Presence of Noise

    Energy Technology Data Exchange (ETDEWEB)

    Nygaard, K.

    1966-09-15

    The problem of calculating the maximum available timing information contained in nuclear pulses in the presence of noise is solved theoretically. Practical experiments show that the theoretical values can be obtained by very simple, but untraditional, means. An output pulse from a practical filter connected to a charge sensitive amplifier with a Ge(Li) detector showed a rise time of 30 ns and a noise level of less than 5 keV. The time jitter measured was inversely proportional to the pulse height and less than 30 ns for 10 keV pulses. With the timing filter shown solid state detectors can be classified somewhere between Nal scintillators and organic scintillators with respect to time resolution.

  3. Design of one-dimensional optical pulse-shaping filters by time-domain topology optimization

    DEFF Research Database (Denmark)

    Yang, Lirong; Lavrinenko, Andrei; Hvam, Jørn Märcher

    2009-01-01

    Time-domain topology optimization is used here to design optical pulse-shaping filters in Si/SiO2 thin-film systems. A novel envelope objective function as well as explicit penalization are used to adapt the optimization method to this unique class of design problems.......Time-domain topology optimization is used here to design optical pulse-shaping filters in Si/SiO2 thin-film systems. A novel envelope objective function as well as explicit penalization are used to adapt the optimization method to this unique class of design problems....

  4. Influence of operating parameters on cake formation in pilot scale pulse-jet bag filter.

    Science.gov (United States)

    Saleem, Mahmood; Krammer, Gernot; Khan, Rafi Ullah; Tahir, M Suleman

    2012-07-01

    Bag filters are commonly used for fine particles removal in off-gas purification. There dust laden gas pervades through permeable filter media starting at a lower pressure drop limit leaving dust (called filter cake) on the filter media. The filter cakeformation is influenced by many factors including filtration velocity, dust concentration, pressure drop limits, and filter media resistance. Effect of the stated parameters is investigated experimentally in a pilot scale pulse-jet bag filter test facility where lime stone dust is separated from air at ambient conditions. Results reveal that filtration velocity significantly affects filter pressure drop as well as cake properties; cake density and specific cake resistance. Cake density is slightly affected by dust concentration. Specific resistance of filter cake increases with velocity, slightly affected by dust concentration, changes inversely with the upper pressure drop limit and decreases over a prolonged use (aging). Specific resistance of filter media is independent of upper pressure drop limit and increases linearly over a prolonged use.

  5. Influence of Pulse Shaping Filters on PAPR Performance of Underwater 5G Communication System Technique: GFDM

    Directory of Open Access Journals (Sweden)

    Jinqiu Wu

    2017-01-01

    Full Text Available Generalized frequency division multiplexing (GFDM is a new candidate technique for the fifth generation (5G standard based on multibranch multicarrier filter bank. Unlike OFDM, it enables the frequency and time domain multiuser scheduling and can be implemented digitally. It is the generalization of traditional OFDM with several added advantages like the low PAPR (peak to average power ratio. In this paper, the influence of the pulse shaping filter on PAPR performance of the GFDM system is investigated and the comparison of PAPR in OFDM and GFDM is also demonstrated. The PAPR is restrained by selecting proper parameters and filters to make the underwater acoustic communication more efficient.

  6. Noise filtering of composite pulses for singlet-triplet qubits

    Science.gov (United States)

    Yang, Xu-Chen; Wang, Xin

    2016-01-01

    Semiconductor quantum dot spin qubits are promising candidates for quantum computing. In these systems, the dynamically corrected gates offer considerable reduction of gate errors and are therefore of great interest both theoretically and experimentally. They are, however, designed under the static-noise model and may be considered as low-frequency filters. In this work, we perform a comprehensive theoretical study of the response of a type of dynamically corrected gates, namely the supcode for singlet-triplet qubits, to realistic 1/f noises with frequency spectra 1/ωα. Through randomized benchmarking, we have found that supcode offers improvement of the gate fidelity for α  1 and the improvement becomes exponentially more pronounced with the increase of the noise exponent in the range 1  α ≤ 3 studied. On the other hand, for small α, supcode will not offer any improvement. The δJ-supcode, specifically designed for systems where the nuclear noise is absent, is found to offer additional error reduction than the full supcode for charge noises. The computed filter transfer functions of the supcode gates are also presented. PMID:27383129

  7. Noise filtering of composite pulses for singlet-triplet qubits

    Science.gov (United States)

    Yang, Xu-Chen; Wang, Xin

    2016-07-01

    Semiconductor quantum dot spin qubits are promising candidates for quantum computing. In these systems, the dynamically corrected gates offer considerable reduction of gate errors and are therefore of great interest both theoretically and experimentally. They are, however, designed under the static-noise model and may be considered as low-frequency filters. In this work, we perform a comprehensive theoretical study of the response of a type of dynamically corrected gates, namely the SUPCODE for singlet-triplet qubits, to realistic 1/f noises with frequency spectra 1/ωα. Through randomized benchmarking, we have found that SUPCODE offers improvement of the gate fidelity for α  1 and the improvement becomes exponentially more pronounced with the increase of the noise exponent in the range 1  α ≤ 3 studied. On the other hand, for small α, SUPCODE will not offer any improvement. The δJ-SUPCODE, specifically designed for systems where the nuclear noise is absent, is found to offer additional error reduction than the full SUPCODE for charge noises. The computed filter transfer functions of the supcode gates are also presented.

  8. Measurement of Ampère-class pulsed electron beams via field emission from carbon-nanotube cathodes in a radiofrequency gun

    Science.gov (United States)

    Mihalcea, D.; Faillace, L.; Hartzell, J.; Panuganti, H.; Boucher, S.; Murokh, A.; Piot, P.; Thangaraj, J. C. T.

    2015-07-01

    Pulsed field emission from cold carbon-nanotube cathodes placed in a radiofrequency resonant cavity was directly measured. The cathodes were located on the backplate of a conventional 1 + /1 2 -cell resonant cavity operating at 1.3-GHz and resulted in the production of bunch train with maximum average current close to 0.7 Ampère. The measured Fowler-Nordheim characteristic, transverse emittance, and pulse duration are presented and, when possible, compared to numerical simulations. The implications of our results to the promise of high-average-current electron sources are briefly discussed.

  9. LMS Adaptive Filtering Applied to a Microwave Arterial Pulse Monitor

    Science.gov (United States)

    1988-12-01

    MIUTION NXTATEME A Approved for pubito r~ ehm DAprib hc"don U&tmod, 1 89 1. 7. 106 • + 5 : .. . . _ -.- + +’ .. d .. . 1 . . . .. . . AFIT/GE/ENG/88D-45...signals were low level and a certain degree of sensor repositioning was required to obtain a strong signal (greater than +/-0.2v). Once acquired...however, signal levels could be maintained at a fairly constant level even - after a slight movement of the pulse monitor. Region 3 exhibited a strong

  10. Transformation of the frequency-modulated continuous-wave field into a train of short pulses by resonant filters

    CERN Document Server

    Shakhmuratov, R N

    2016-01-01

    The resonant filtering method transforming frequency modulated radiation field into a train of short pulses is proposed to apply in optical domain. Effective frequency modulation can be achieved by electro-optic modulator or by resonant frequency modulation of the filter with a narrow absorption line. Due to frequency modulation narrow-spectrum CW radiation field is seen by the resonant filter as a comb of equidistant spectral components separated by the modulation frequency. Tuning narrow-bandwidth filter in resonance with $n$-th spectral component of the comb transforms the radiation field into bunches of pulses with $n$ pulses in each bunch. The transformation is explained by the interference of the coherently scattered resonant component of the field with the whole comb. Constructive interference results in formation of pulses, while destructive interference is seen as dark windows between pulses. It is found that the optimal thickness of the resonant filter is several orders of magnitude smaller than the...

  11. Effect of high substrate bias and hydrogen and nitrogen incorporation on filtered cathodic vacuum arc deposited tetrahedral amorphous carbon films

    Energy Technology Data Exchange (ETDEWEB)

    Panwar, O.S. [Plasma Processed Materials Group, National Physical Laboratory, Dr. K.S. Krishnan Road, New Delhi-110 012 (India)], E-mail: ospanwar@mail.nplindia.ernet.in; Khan, Mohd. Alim [Plasma Processed Materials Group, National Physical Laboratory, Dr. K.S. Krishnan Road, New Delhi-110 012 (India); Kumar, Mahesh; Shivaprasad, S.M. [Surface Physics and Nanostructures Group, National Physical Laboratory, Dr. K.S. Krishnan Road, New Delhi-110 012 (India); Satyanarayana, B.S. [MIT Innovation Centre and Electronics and Communication Department, Manipal Institute of Technology, Manipal-579104 (India); Dixit, P.N. [Plasma Processed Materials Group, National Physical Laboratory, Dr. K.S. Krishnan Road, New Delhi-110 012 (India); Bhattacharyya, R. [Emeritus Scientist, National Physical Laboratory, New Delhi-110012 (India); Khan, M.Y. [Department of Physics, Jamia Millia Islamia, Central University, New Delhi-110025 (India)

    2008-02-29

    The application of a sufficiently high negative substrate bias, during the growth of tetrahedral amorphous carbon (ta-C), is usually associated with low sp{sup 3} bonding configuration and stressed films. However, in an effort to understand and utilize the higher pseudo thermo dynamical conditions during the film growth, at high negative substrate bias (- 300 V), reported here is a study on ta-C films grown under different hydrogen and nitrogen concentration. As grown ta-C films were studied under different negative substrate bias conditions. The variation of the sp{sup 3} content and sp{sup 3}/sp{sup 2} ratio in the ta-C films exhibits a trend similar to those reported in literature, with a subtle variation in this report being the substrate bias voltage, which was observed to be around - 200 V, for obtaining the highest sp{sup 3} (80%) bonding and sp{sup 3}/sp{sup 2} (3.95) ratio. The hydrogen and nitrogen incorporated ta-C films studied, at a bias of - 300 V, show an increase in sp{sup 3} (87-91%) bonding and sp{sup 3}/sp{sup 2} (7-10) ratio in the range of studies reported. The inference is drawn on the basis of the set of data obtained from measurements carried out using X-ray photoelectron spectroscopy, X-ray induced Auger electron spectroscopy and Raman spectroscopy of as grown and hydrogen and nitrogen incorporated ta-C films deposited using an S bend filtered cathodic vacuum arc system. The study indicates the possibility of further tailoring ta-C film properties and also extending capabilities of the cathodic arc system for developing carbon based films for electronics and tribological applications.

  12. Model calibration for pressure drop in a pulse-jet cleaned fabric filter

    Science.gov (United States)

    Koehler, John L.; David, Leith

    A model based on Darcy's law allows prediction of pressure drop in a pulse-jet cleaned fabric filter. The model considers the effects of filtration velocity, dust areal density added during one filtration cycle, and pulse pressure. Data used to calibrate the model were collected in experiments with three fabric surface treatments and three dusts conducted at three filtration velocities, for a total of 27 different experimental conditions. The fabric used was polyester felt with untreated, singed, or PTFE-laminated surface. The dusts used were granite, limestone and fly ash. Filtration velocities were 50,75 and 100 mm s -1. Dust areal density added during one filtration cycle was constant, as was pulse pressure. Under these conditions, fabric surface treatment alone largely determined the values for two of the three constants in the model; the third constant depends on pressure drop characteristics of the venturi at the top of each filter bag.

  13. Influence of gas pressure on electron beam emission current of pulsed cathodic-arc-based forevacuum plasma electron source

    Science.gov (United States)

    Burdovitsin, Victor A.; Kazakov, Andrey V.; Medovnik, Alexander V.; Oks, Efim M.

    2017-09-01

    We describe our experimental investigation of the effect of background gas pressure on the emission parameters of a pulsed cathodic-arc-based forevacuum-pressure plasma-cathode electron source. We find that increased gas pressure over the range 4-16 Pa significantly reduces the beam current rise-time and significantly increases the emission current amplitude. For example, at a discharge current of 20 A, increasing the working gas pressure from 4 Pa to 16 Pa increases the emission current from 8 A to 18 A and shortens the beam rise-time from 50 μs to 20 μs. This influence of gas pressure on the electron beam parameters can be explained by the effect of arc discharge current switching from the anode to emission. In our case, the current switching effect is caused by increased working gas pressure. In the forevacuum pressure range, the increase of the electron emission current with the growth of gas pressure is due to a rise in the emission plasma potential which is caused by ion back-streaming from the plasma formed in the electron beam transport region. A model describing the influence of gas pressure on the electron emission from the plasma is presented.

  14. Extending the dynamic range of copper determination in differential pulse adsorption cathodic stripping voltammetry using wavelet neural network.

    Science.gov (United States)

    Khayamian, T; Ensafi, Ali A; Benvidi, A

    2006-07-15

    A wavelet neural network (WNN) model is proposed for extending the dynamic range of Cu(II) determination by differential pulse adsorption cathodic stripping voltammetry (DP-AdSV) using xylenol orange (XO) as a suitable ligand. All of voltammograms data consisting of Cu(II) and Cu(II)-XO peak currents were used in WNN model. The WNN model consisted of three layers (2-8-1) with the Morlet mother wavelet transfer function in the hidden layer. The model was able to extend the dynamic range of Cu(II) from its narrow linear range (1-50 ng ml(-1)) to the higher dynamic range (1-1500 ng ml(-1)). The results of the WNN model was also compared with artificial neural network (ANN) model and it was demonstrated the superiority of the WNN model relative to ANN model.

  15. Properties of boron and phosphorous incorporated tetrahedral amorphous carbon films grown using filtered cathodic vacuum arc process

    Energy Technology Data Exchange (ETDEWEB)

    Panwar, O.S., E-mail: ospanwar@mail.nplindia.ernet.in [Plasma Processed Materials Group, National Physical Laboratory (CSIR), Dr. K.S. Krishnan Road, New Delhi 110012 (India); Khan, Mohd Alim [Plasma Processed Materials Group, National Physical Laboratory (CSIR), Dr. K.S. Krishnan Road, New Delhi 110012 (India); Satyanarayana, B.S. [40, Sreeniketan, NDSE 24, New Delhi 110096 (India); Kumar, Sushil; Ishpal [Plasma Processed Materials Group, National Physical Laboratory (CSIR), Dr. K.S. Krishnan Road, New Delhi 110012 (India)

    2010-04-15

    This paper reports the electrical, mechanical, structural and field emission properties of as grown and also boron and phosphorous incorporated tetrahedral amorphous carbon (ta-C) films, deposited using a filtered cathodic vacuum arc process. The effect of varying boron and phosphorous content (up to 2.0 at.% in to ta-C) on the conductivity ({sigma}{sub D}), activation energy ({Delta}E{sub 1}), hardness, microstructure, emission threshold (E{sub turn-ON}) and emission current density (J) at 12.5 V/{mu}m of ta-C: B and ta-C: P films deposited at a high negative substrate bias of -300 V are reported. It is observed that both boron and phosphorous incorporation leads to a nearly an order increase in {sigma}{sub D} and corresponding decrease in {Delta}E{sub 1} and a slight increase in hardness as compared to as grown ta-C films. In the case of field assisted electron emission, it is observed that E{sub turn-ON} increases and J decreases. The changes are attributed to the changes in the sp{sup 3}/sp{sup 2} ratio of the films due to boron and phosphorous incorporation. The effect of boron on ta-C is to give a p-type effect whereas the effect of phosphorous gives n-type doping effect.

  16. Density changes with substrate negative bias for ta-C films deposited by filter cathode vacuum arc

    Institute of Scientific and Technical Information of China (English)

    TAN Man-lin; ZHU Jia-qi; HAN Jie-cai; MENG Song-he

    2004-01-01

    Specular X-ray reflectivity (XRR) measurements were used to study the density and cross-section information of tetrahedral amorphous carbon (ta-C) films deposited by filter cathode vacuum arc(FCVA) system at different substrate bias. According to the correlation between density and substrate negative bias, it is found that the value of density reaches a maximum at -80 V bias. As the substrate bias increases or decreases, the density tends to lower gradually. Based on the density of diamond and graphite, sp3 bonding ratio of ta-C films was obtained from their corresponding density according to a simple equation between the two. And a similar parabolic variation was observed for ta-C films with the sp3 content changes with substrate negative bias. The mechanical properties such as hardness and elastic modulus were also measured and compared with the corresponding density for ta-C films. From the distribution of data points, a linear proportional correlation between them was found, which shows that the density is a critical parameter to characterize the structure variation for ta-C films.

  17. Friction properties of amorphous carbon ultrathin films deposited by filtered cathodic vacuum arc and radio-frequency sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Matlak, J.; Komvopoulos, K., E-mail: kyriakos@me.berkeley.edu

    2015-03-31

    The friction properties of ultrathin films of amorphous carbon (a-C) deposited on Si(100) substrates by filtered cathodic vacuum arc and radio-frequency sputtering were investigated by surface force microscopy. Deposition parameters yielding a-C films with high sp{sup 3} content were used to deposit films of thickness between 5 and 35 nm. The coefficient of friction of both types of a-C films was measured with a 1-μm-radius conical diamond tip and normal loads in the range of 20–640 μN. The results show a strong dependence of the friction properties on the surface roughness, thickness, and structure of the a-C films, which are influenced by the intricacies of the deposition method. The dependence of the coefficient of friction on normal load and the dominance of adhesion and plowing friction mechanisms are interpreted in terms of the through-thickness variation of carbon atom hybridization of the a-C films. - Highlights: • Comparison of nanoscale friction properties of ultrathin amorphous carbon films. • Friction dependence on film roughness, thickness, and structure (hybridization). • Effect of through-thickness changes in carbon atom hybridization on film friction. • Explanation of film friction trends in terms of competing friction mechanisms.

  18. Effects of filtered cathodic vacuum arc deposition (FCVAD) conditions on photovoltaic TiO{sub 2} films

    Energy Technology Data Exchange (ETDEWEB)

    Aramwit, C. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Intarasiri, S. [Science and Technology Research Institute, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Bootkul, D. [Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Department of General Science, Faculty of Science, Srinakharinwirot University, Bangkok 10110 (Thailand); Tippawan, U. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Supsermpol, B.; Seanphinit, N. [Department of General Science, Faculty of Science, Srinakharinwirot University, Bangkok 10110 (Thailand); Western Digital Thailand Co. Ltd., Ayutthaya 13160 (Thailand); Ruangkul, W. [Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Yu, L.D., E-mail: yuld@thep-center.org [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand)

    2014-08-15

    Highlights: • Titanium dioxide films were synthesized using the FCVAD technique. • Various FCVAD conditions were tested. • The TiO{sub 2} films were characterized. • The FCVAD condition effects on the film characteristics were studied. • The O{sub 2} pressure had the most important effect on the film quality. - Abstract: Titanium dioxide (TiO{sub 2}) films for photovoltaic applications were synthesized using filtered cathodic vacuum arc deposition (FCVAD) technique. Various deposition conditions were tested for an optimal film formation. The conditions included the oxygen (O{sub 2}) pressure which was varied from a base pressure 10{sup −5} to 10{sup −4}, 10{sup −3}, 10{sup −2} and 10{sup −1} Torr, sample holder bias varied using 0 or −250 V, deposition time varied from 10, 20 to 30 min, and deposition distance varied from 1 to 3 cm. The deposited films were also annealed and compared with unannealed ones. The films under various conditions were characterized using optical microscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), energy-dispersive X-ray spectroscopy (EDS) and Raman spectroscopy techniques. The film transparency increased and thickness decreased to a nanoscale with increasing of the O{sub 2} pressure. The transparent deposited films contained stoichiometric titanium and oxygen under the medium O{sub 2} pressure. The as-deposited films were TiO{sub 2} containing some rutile but no anatase which needed annealing to form.

  19. Deposition of TiN Films by Novel Filter Cathodic Arc Technique

    Institute of Scientific and Technical Information of China (English)

    NIU Er-Wu; FAN Song-Hua; LI Li; L(U) Guo-Hua; FENG Wen-Ran; ZHANG Gu-Ling; YANG Si-Ze

    2006-01-01

    A straight magnetic filtering arc source is used to deposit thin films of titanium nitride.The properties of thefilms depend strongly on the deposition process.TiN films can be deposited directly onto heated substrates in anitrogen atmosphere or onto unbiased substrates by condensing the Ti+ ion beam in about 300 eV N2+ nitrogen ionbombardment.In the latter case.the film stoichiometry is varied from an N:Ti ratio of 0.6-1.1 by controlling thearrival rates of Ti and nitrogen ions.Meanwhile,simple models are used to describe the evolution of compressivestress as function of the arrival ratio and the composition of the ion-assisted TiN films.

  20. Design of FIR digital filters for pulse shaping and channel equalization using time-domain optimization

    Science.gov (United States)

    Houts, R. C.; Vaughn, G. L.

    1974-01-01

    Three algorithms are developed for designing finite impulse response digital filters to be used for pulse shaping and channel equalization. The first is the Minimax algorithm which uses linear programming to design a frequency-sampling filter with a pulse shape that approximates the specification in a minimax sense. Design examples are included which accurately approximate a specified impulse response with a maximum error of 0.03 using only six resonators. The second algorithm is an extension of the Minimax algorithm to design preset equalizers for channels with known impulse responses. Both transversal and frequency-sampling equalizer structures are designed to produce a minimax approximation of a specified channel output waveform. Examples of these designs are compared as to the accuracy of the approximation, the resultant intersymbol interference (ISI), and the required transmitted energy. While the transversal designs are slightly more accurate, the frequency-sampling designs using six resonators have smaller ISI and energy values.

  1. The use of nylon and glass fiber filter separators with different pore sizes in air-cathode single-chamber microbial fuel cells

    KAUST Repository

    Zhang, Xiaoyuan

    2010-01-01

    Separators are needed in microbial fuel cells (MFCs) to reduce electrode spacing and preventing electrode short circuiting. The use of nylon and glass fiber filter separators in single-chamber, air-cathode MFCs was examined for their effect on performance. Larger pore nylon mesh were used that had regular mesh weaves with pores ranging from 10 to 160 μm, while smaller pore-size nylon filters (0.2-0.45 μm) and glass fiber filters (0.7-2.0 μm) had a more random structure. The pore size of both types of nylon filters had a direct and predictable effect on power production, with power increasing from 443 ± 27 to 650 ± 7 mW m-2 for pore sizes of 0.2 and 0.45 μm, and from 769 ± 65 to 941 ± 47 mW m-2 for 10 to 160 μm. In contrast, changes in pore sizes of the glass fiber filters resulted in a relatively narrow change in power (732 ± 48 to 779 ± 43 mW m-2) for pore sizes of 0.7 to 2 μm. An ideal separator should increase both power density and Coulombic efficiency (CE). However, CEs measured for the different separators were inversely correlated with power production, demonstrating that materials which reduced the oxygen diffusion into the reactor also hindered proton transport to the cathode, reducing power production through increased internal resistance. Our results highlight the need to develop separators that control oxygen transfer and facilitate proton transfer to the cathode. © 2010 The Royal Society of Chemistry.

  2. Cuff-less blood pressure measurement using pulse arrival time and a Kalman filter

    Science.gov (United States)

    Zhang, Qiang; Chen, Xianxiang; Fang, Zhen; Xue, Yongjiao; Zhan, Qingyuan; Yang, Ting; Xia, Shanhong

    2017-02-01

    The present study designs an algorithm to increase the accuracy of continuous blood pressure (BP) estimation. Pulse arrival time (PAT) has been widely used for continuous BP estimation. However, because of motion artifact and physiological activities, PAT-based methods are often troubled with low BP estimation accuracy. This paper used a signal quality modified Kalman filter to track blood pressure changes. A Kalman filter guarantees that BP estimation value is optimal in the sense of minimizing the mean square error. We propose a joint signal quality indice to adjust the measurement noise covariance, pushing the Kalman filter to weigh more heavily on measurements from cleaner data. Twenty 2 h physiological data segments selected from the MIMIC II database were used to evaluate the performance. Compared with straightforward use of the PAT-based linear regression model, the proposed model achieved higher measurement accuracy. Due to low computation complexity, the proposed algorithm can be easily transplanted into wearable sensor devices.

  3. Pulsed laser deposition-assisted synthesis of porous WP2 nanosheet arrays integrated on graphite paper as a 3D flexible cathode for efficient hydrogen evolution

    Science.gov (United States)

    Pi, Mingyu; Guo, Weimeng; Wu, Tianli; Wang, Xiaodeng; Zhang, Dingke; Wang, Shuxia; Chen, Shijian

    2017-10-01

    Herein, porous WP2 nanosheet arrays integrated on graphite paper (P-WP2 NSs/GP) as 3D flexible cathode for electrocatalytic hydrogen evolution reaction (HER) are prepared by in situ phosphidation via vacuum encapsulation assisted by pulsed laser deposition technique. Compared to the electrode without pre-deposition process, the enhanced catalytic activities are attributed to the increased effective catalyst loading and the reinforced charge transport kinetics. The results make the present P-WP2 NSs/GP as a promising cathode for energy conversion and paves a new way for designing and fabricating efficient electrodes toward HER.

  4. Interface control of atomic layer deposited oxide coatings by filtered cathodic arc deposited sublayers for improved corrosion protection

    Energy Technology Data Exchange (ETDEWEB)

    Härkönen, Emma, E-mail: emma.harkonen@helsinki.fi [Laboratory of Inorganic Chemistry, University of Helsinki, P.O. Box 55, FIN-00014 Helsinki (Finland); Tervakangas, Sanna; Kolehmainen, Jukka [DIARC-Technology Inc., Espoo (Finland); Díaz, Belén; Światowska, Jolanta; Maurice, Vincent; Seyeux, Antoine; Marcus, Philippe [Laboratoire de Physico-Chimie des Surfaces, CNRS (UMR 7075) – Chimie ParisTech (ENSCP), F-75005 Paris (France); Fenker, Martin [FEM Research Institute, Precious Metals and Metals Chemistry, D-73525 Schwäbisch Gmünd (Germany); Tóth, Lajos; Radnóczi, György [Research Centre for Natural Sciences HAS, (MTA TKK), Budapest (Hungary); Ritala, Mikko [Laboratory of Inorganic Chemistry, University of Helsinki, P.O. Box 55, FIN-00014 Helsinki (Finland)

    2014-10-15

    Sublayers grown with filtered cathodic arc deposition (FCAD) were added under atomic layer deposited (ALD) oxide coatings for interface control and improved corrosion protection of low alloy steel. The FCAD sublayer was either Ta:O or Cr:O–Ta:O nanolaminate, and the ALD layer was Al{sub 2}O{sub 3}–Ta{sub 2}O{sub 5} nanolaminate, Al{sub x}Ta{sub y}O{sub z} mixture or graded mixture. The total thicknesses of the FCAD/ALD duplex coatings were between 65 and 120 nm. Thorough analysis of the coatings was conducted to gain insight into the influence of the FCAD sublayer on the overall coating performance. Similar characteristics as with single FCAD and ALD coatings on steel were found in the morphology and composition of the duplex coatings. However, the FCAD process allowed better control of the interface with the steel by reducing the native oxide and preventing its regrowth during the initial stages of the ALD process. Residual hydrocarbon impurities were buried in the interface between the FCAD layer and steel. This enabled growth of ALD layers with improved electrochemical sealing properties, inhibiting the development of localized corrosion by pitting during immersion in acidic NaCl and enhancing durability in neutral salt spray testing. - Highlights: • Corrosion protection properties of ALD coatings were improved by FCAD sublayers. • The FCAD sublayer enabled control of the coating-substrate interface. • The duplex coatings offered improved sealing properties and durability in NSS. • The protective properties were maintained during immersion in a corrosive solution. • The improvements were due to a more ideal ALD growth on the homogeneous FCAD oxide.

  5. Differential pulse cathodic stripping voltammetric determination of uranium with arsenazo-III at the hanging mercury dropping electrode

    Energy Technology Data Exchange (ETDEWEB)

    Kadi, M.W.; El-Shahawi, M.S. [Chemistry Dept., King Abdulaziz Univ., Jeddah (Saudi Arabia)

    2009-07-01

    An accurate, inexpensive and less laborious controlled adsorptive accumulation of uranium(VI)-arsenazo-III on a hanging mercury drop electrode (HMDE) has been developed for uranium(VI) determination. The method is based upon the collection of uranium(VI)-arsenazo-III complex at pH 5-6 at the HMDE and subsequent direct stripping measurement of the element in the nanomolar concentration level. The cathodic peak current (i{sub p,c}) of the adsorbed complex ions of uranium(VI) was measured at -0.35 V vs. Ag/AgCl reference electrode by differential pulse cathodic stripping voltammetry (DP-CSV), proceeded by an accumulation period of 150s2.5 in Britton-Robinson buffer of pH 5. The plot of the resulting i{sub p,c} vs. uranium(VI) concentration was linear in the range 2.1 x 10{sup -9} to 9.60 x 10{sup -7} mol L{sup -1} uranium(VI) and tended to level off at above 9.6 x 10{sup -7} mol L{sup -1}. The limits of detection and quantification of uranium(VI) were found to be 4.7 x 10{sup -10} and 1.5 x 10{sup -9} mol L{sup -1}, respectively. A relative standard deviation of {+-}2.39% (n = 5) at 8.5 x 10{sup -7} mol L{sup -1} uranium(VI) was obtained. The method was validated by comparing the results with that obtained by ICP-MS method with RSD less than {+-}3.3%. The method was applied successfully for the analysis of uranium in certified reference material (IAEA soil-7), and in phosphate fertilizers. (orig.)

  6. On the Forming Mechanism of the Cleaning Airflow of Pulse-jet Fabric Filters.

    Science.gov (United States)

    Jiying, Cai; Wenge, Hao; Cong, Zhang; Jiaqi, Yu; Ting, Wang

    2017-04-05

    To reveal the formation mechanism of a pulse-jet airflow's cleaning effect in a filter bag, a theoretical model is built by using the theory of gas jet and unitary adiabatic flow according to given specifications and dimensions of the bags and resistance characteristics of the cloth and dust layer. It is about the relationship between cleaning system structure and operating parameters. The model follows the principle that the flow and kinetic energy of jet flow injected into a filter bag should be consistent with the flow of cleaning airflow in the bag and the pressure drop flowing through the filter cloth and dust layer. The purpose of the model is to achieve the peak pressure of cleaning airflow, which dominates the effect of the pulse-jet cleaning process. The cleaning system structure includes air pressure in the nozzle, structure and size of nozzle, exit velocity of nozzle, jet distance and diameter of jet cross-section. Based on the condition of cleaning system structure and operating parameters established by using the theoretical model, Fluent software is applied to carry out a numerical simulation of the jet airflow field at the nozzle's outlet, jet airflow field between nozzle and bag top, and cleaning airflow field in the filter bag. Experimental results are used to verify the reliability of the theoretical model. They are obtained in a pilot-scale test filter with a single bag, in length of 2m and in general full-scale dimensions of the cleaning system. The results show that when any rectification measure is not installed at the bag opening, the cross-sectional area covered by jet gas is hardly sufficient to cover the entire area of the bag opening. A large portion of the gases injected into the filter bag will overflow reversely upward from the edge due to pressure differences between the upper area and lower area inside the bag opening. This led to a serious shortage of the cleaning airflow and a limited increase in static pressure. When a venturi

  7. On the effects of quantization on mismatched pulse compression filters designed using L-p norm minimization techniques

    CSIR Research Space (South Africa)

    Cilliers, Jacques E

    2007-10-01

    Full Text Available In [1] the authors introduced a technique for generating mismatched pulse compression filters for linear frequency chirp signals. The technique minimizes the sum of the pulse compression sidelobes in a p L –norm sense. It was shown that extremely...

  8. Direct determination of praziquantel in pharmaceutical formulations and human plasma by cathodic adsorptive stripping differential-pulse voltammetry.

    Science.gov (United States)

    Ghoneim, M M; Mabrouk, M M; Tawfik, A

    2002-11-07

    The polarographic and cyclic voltammetric behaviour of praziquantel was studied in B.R. buffers of different pH values. Contradictory to that mentioned in a previously published work, praziquantel is an electro-active compound. Its polarogram exhibited a single 2-electron irreversible reduction wave in B.R. buffer of pH 5, the wave height decreased on the increase of pH till it disappeared in solution of pH >7. This wave was attributed to the reduction of the Cz.dbnd6;O double bond. The quantitative trace determination of bulk praziquantel was studied at a hanging mercury drop electrode by cathodic adsorptive stripping differential-pulse voltammetry. A fully validated sensitive procedure based on controlled adsorptive accumulation of the drug onto a HMDE was developed for its direct determination without derivatization. Accumulation of praziquantel was found to be optimized in 0.1 M Na(2)SO(4) solution as supporting electrolyte under the following conditions: accumulation potential, -1.2 V (vs. Ag/AgCl/KCl(s)); accumulation time, 30 s; scan rate, 10 mV/s and pulse height 100 mV. The proposed procedure was applied successfully for determination of praziquantel in its pharmaceutical formulations and human plasma. The mean recoveries of the drug were 98.85-99.42% and 99.12-100.47% with RSD of 0.49-0.95% and 0.45-0.52% in pharmaceutical formulations and human plasma, respectively. Limits of detection and quantitation of 1.14x10(-9) and 3.80x10(-9) M praziquantel, respectively, were achieved.

  9. Determination of propylthiouracil in pharmaceuticals by differential pulse voltammetry using a cathodically pretreated boron-doped diamond electrode

    Energy Technology Data Exchange (ETDEWEB)

    Sartori, Elen Romao [Universidade Estadual de Londrina, PR (Brazil). Dept. de Quimica; Trench, Aline Barrios; Rocha-Filho, Romeu C.; Fatibello-Filho, Orlando, E-mail: bello@ufscar.br [Universidade Federal de Sao Carlos (UFSCAR), SP (Brazil). Dept. de Quimica

    2013-09-15

    A simple procedure is described for the determination of propylthiouracil (PTU) by differential pulse voltammetry (DPV) using a cathodically pretreated boron-doped diamond (BDD) electrode. Cyclic voltammetry studies indicate that the oxidation of PTU is irreversible at a peak potential of 1.42 V (vs. Ag/AgCl (3.0 mol L{sup -1} KCl)) in a Britton-Robinson (BR) buffer solution (pH 2.0). Under optimized conditions, the obtained analytical curve was linear (r = 0.9985) for the PTU concentration range of 1.0 to 29.1 {mu}mol L{sup -1} in a BR buffer solution (pH 2.0), with a detection limit of 0.90 {mu}mol L{sup -1}. The proposed method was successfully applied in the determination of PTU in pharmaceutical samples, with results in agreement at a 95% confidence level with those obtained using an official titration method. (author)

  10. Spectral filtering in pulsed photothermal temperature profiling of collagen tissue phantoms

    Science.gov (United States)

    Milanič, Matija; Majaron, Boris

    2009-11-01

    We present an experimental comparison of pulsed photothermal (PPT) profiling in collagen-based tissue phantoms utilizing different midinfrared spectral bands. Laser-induced temperature profiles are reconstructed using a custom optimization code within the customary monochromatic approximation. Both experimental results and a detailed numerical simulation of the procedure demonstrate that, despite the associated reduction of signal-to-noise ratio, appropriate spectral filtering reduces the broadening of temperature peaks and thus improves the accuracy of temperature profiling. For our experimental system, best performance is obtained when applying a long-pass filter with cut-on wavelength at 3.4-3.8 μm. Because our collagen gel mimics infrared and thermal properties of human skin, we believe that this conclusion is transferrable to PPT radiometric profiling of human skin in vivo.

  11. Spectral filtering in pulsed photothermal temperature profiling of collagen tissue phantoms.

    Science.gov (United States)

    Milanic, Matija; Majaron, Boris

    2009-01-01

    We present an experimental comparison of pulsed photothermal (PPT) profiling in collagen-based tissue phantoms utilizing different midinfrared spectral bands. Laser-induced temperature profiles are reconstructed using a custom optimization code within the customary monochromatic approximation. Both experimental results and a detailed numerical simulation of the procedure demonstrate that, despite the associated reduction of signal-to-noise ratio, appropriate spectral filtering reduces the broadening of temperature peaks and thus improves the accuracy of temperature profiling. For our experimental system, best performance is obtained when applying a long-pass filter with cut-on wavelength at 3.4-3.8 microm. Because our collagen gel mimics infrared and thermal properties of human skin, we believe that this conclusion is transferrable to PPT radiometric profiling of human skin in vivo.

  12. Regression Analysis of the Effect of Bias Voltage on Nano- and Macrotribological Properties of Diamond-Like Carbon Films Deposited by a Filtered Cathodic Vacuum Arc Ion-Plating Method

    Directory of Open Access Journals (Sweden)

    Shojiro Miyake

    2014-01-01

    Full Text Available Diamond-like carbon (DLC films are deposited by bend filtered cathodic vacuum arc (FCVA technique with DC and pulsed bias voltage. The effects of varying bias voltage on nanoindentation and nanowear properties were evaluated by atomic force microscopy. DLC films deposited with DC bias voltage of −50 V exhibited the greatest hardness at approximately 50 GPa, a low modulus of dissipation, low elastic modulus to nanoindentation hardness ratio, and high nanowear resistance. Nanoindentation hardness was positively correlated with the Raman peak ratio Id/Ig, whereas wear depth was negatively correlated with this ratio. These nanotribological properties highly depend on the films’ nanostructures. The tribological properties of the FCVA-DLC films were also investigated using a ball-on-disk test. The average friction coefficient of DLC films deposited with DC bias voltage was lower than that of DLC films deposited with pulse bias voltage. The friction coefficient calculated from the ball-on-disk test was correlated with the nanoindentation hardness in dry conditions. However, under boundary lubrication conditions, the friction coefficient and specific wear rate had little correlation with nanoindentation hardness, and wear behavior seemed to be influenced by other factors such as adhesion strength between the film and substrate.

  13. Nitrogen doping for adhesion improvement of DLC film deposited on Si substrate by Filtered Cathodic Vacuum Arc (FCVA) technique

    Energy Technology Data Exchange (ETDEWEB)

    Bootkul, D., E-mail: mo_duangkhae@hotmail.com [Department of General Science, Faculty of Science, Srinakharinwirot University, Bangkok 10110 (Thailand); Supsermpol, B.; Saenphinit, N. [Western Digital Company, Ayutthaya 13160 (Thailand); Aramwit, C. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50202 (Thailand); Intarasiri, S., E-mail: saweat@gmail.com [Science and Technology Research Institute, Chiang Mai University, Chiang Mai 50202 (Thailand)

    2014-08-15

    Diamond-like carbon (DLC) films have been used in many applications due to their attractive combination of properties including chemical inertness, corrosion protection, biocompatibility, high hardness, and low wear rates. However, they still have some limitations such as high internal stresses and low toughness which lead to poor adhesion of films. Synthesis of nitrogen-doped DLC (N-DLC) offers the possibility of overcoming these limitations. In this study, DLC films, namely tetrahedral amorphous carbon (ta-C) and nitrogen doped tetrahedral amorphous carbon (ta-C:N) were deposited on single crystalline Si wafer substrates using the Filtered Cathodic Vacuum Arc (FCVA) technique. Film characterizations were carried out by Raman spectroscopy, atomic force microscopy (AFM), scanning electron microscopy (SEM), triboindenter tester and nano-scratch tester. Measurement results showed that intentionally doping with nitrogen reduced the carbon sp{sup 3} content and increased the surface roughness in comparison with that of pure ta-C films. The hardness measurement confirmed the Raman and AFM analyses that adding nitrogen in ta-C films decreased the hardness, especially with high nitrogen content. However, the nano-scratch test revealed the increasing of the critical load with nitrogen. This work, then, extended its scope to investigate the properties of double-layer ta-C films which were composed of ta-C:N interlayer of various thickness around 10–30 nm and ta-C top-layer with thickness of around 80 nm. Microstructure characterization demonstrated that a ta-C:N interlayer gradually decreased the sp{sup 3} fraction in the films and increased film roughness whenever the ta-C:N interlayer thickness increased. In this structure, the tribological property in terms of adhesion to the Si substrate was significantly improved by about 20–90%, but the mechanical property in terms of hardness was gradually degraded by about 2–10%, compared to pure ta-C film, when the ta

  14. A novel non-linear recursive filter design for extracting high rate pulse features in nuclear medicine imaging and spectroscopy.

    Science.gov (United States)

    Sajedi, Salar; Kamal Asl, Alireza; Ay, Mohammad R; Farahani, Mohammad H; Rahmim, Arman

    2013-06-01

    Applications in imaging and spectroscopy rely on pulse processing methods for appropriate data generation. Often, the particular method utilized does not highly impact data quality, whereas in some scenarios, such as in the presence of high count rates or high frequency pulses, this issue merits extra consideration. In the present study, a new approach for pulse processing in nuclear medicine imaging and spectroscopy is introduced and evaluated. The new non-linear recursive filter (NLRF) performs nonlinear processing of the input signal and extracts the main pulse characteristics, having the powerful ability to recover pulses that would ordinarily result in pulse pile-up. The filter design defines sampling frequencies lower than the Nyquist frequency. In the literature, for systems involving NaI(Tl) detectors and photomultiplier tubes (PMTs), with a signal bandwidth considered as 15 MHz, the sampling frequency should be at least 30 MHz (the Nyquist rate), whereas in the present work, a sampling rate of 3.3 MHz was shown to yield very promising results. This was obtained by exploiting the known shape feature instead of utilizing a general sampling algorithm. The simulation and experimental results show that the proposed filter enhances count rates in spectroscopy. With this filter, the system behaves almost identically as a general pulse detection system with a dead time considerably reduced to the new sampling time (300 ns). Furthermore, because of its unique feature for determining exact event times, the method could prove very useful in time-of-flight PET imaging.

  15. Generation of uniform low-temperature plasma in a pulsed non-self-sustained glow discharge with a large-area hollow cathode

    Science.gov (United States)

    Akhmadeev, Yu. H.; Denisov, V. V.; Koval, N. N.; Kovalsky, S. S.; Lopatin, I. V.; Schanin, P. M.; Yakovlev, V. V.

    2017-01-01

    Generation of plasma in a pulsed non-self-sustained glow discharge with a hollow cathode with an area of ≥2 m2 at gas pressures of 0.4-1 Pa was studied experimentally. At an auxiliary arc-discharge current of 100 A and a main discharge voltage of 240 V, a pulse-periodic glow discharge with a current amplitude of 370 A, pulse duration of 340 μs, and repetition rate of 1 kHz was obtained. The possibility of creating a uniform gas-discharge plasma with a density of up to 1012 cm-3 and an electron temperature of 1 eV in a volume of >0.2 m3 was demonstrated. Such plasma can be efficiently used to treat material surfaces and generate pulsed ion beams with a current density of up to 15 mA/cm2.

  16. Influence of pulsed substrate bias on the structure and properties of Ti-Al-N films deposited by cathodic vacuum arc

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, G.P., E-mail: princeterry@163.com [Institute of Physics, Chinese Academy of Science, Beijing 100080 (China); Gao, G.J. [Changchun University of Science and Technology, College of Science, Changchun 130000 (China); Wang, X.Q.; Lv, G.H.; Zhou, L.; Chen, H.; Pang, H.; Yang, S.Z. [Institute of Physics, Chinese Academy of Science, Beijing 100080 (China)

    2012-07-15

    Ti-Al-N films were deposited by cathodic vacuum arc (CVA) technique in N{sub 2} atmosphere with different pulsed substrate bias. The influence of pulsed substrate bias (0 to -800 V) on the deposition rate, surface morphology, crystal structure, and mechanical properties of the Ti-Al-N films were systematically investigated. Increasing pulsed bias voltage resulted in the decrease of deposition rate but the increase of surface roughness. It was found that there was a strong correlation between the pulsed bias and film structure. All the films studied in this paper were composed of TiN, AlN, and Ti-Al-N ternary phases. The grains changed from equiaxial to columnar and exhibited preferred orientation when the pulsed bias increased. With the increase of pulsed bias voltage, the atomic ratio of Ti to Al element increased gradually, while the N to (Ti + Al) ratio decreased. The composite films present an enhanced nanohardness compared with binary TiN and ZrN films. The film deposited with pulsed bias of -200 V possessed the maximum scratch critical load and nanohardness. The minimum friction coefficient with pulsed bias of -300 V was obtained.

  17. Comparison of parabolic filtration methods for 3D filtered back projection in pulsed EPR imaging.

    Science.gov (United States)

    Qiao, Zhiwei; Redler, Gage; Epel, Boris; Halpern, Howard J

    2014-11-01

    Pulse electron paramagnetic resonance imaging (Pulse EPRI) is a robust method for noninvasively measuring local oxygen concentrations in vivo. For 3D tomographic EPRI, the most commonly used reconstruction algorithm is filtered back projection (FBP), in which the parabolic filtration process strongly influences image quality. In this work, we designed and compared 7 parabolic filtration methods to reconstruct both simulated and real phantoms. To evaluate these methods, we designed 3 error criteria and 1 spatial resolution criterion. It was determined that the 2 point derivative filtration method and the two-ramp-filter method have unavoidable negative effects resulting in diminished spatial resolution and increased artifacts respectively. For the noiseless phantom the rectangular-window parabolic filtration method and sinc-window parabolic filtration method were found to be optimal, providing high spatial resolution and small errors. In the presence of noise, the 3 point derivative method and Hamming-window parabolic filtration method resulted in the best compromise between low image noise and high spatial resolution. The 3 point derivative method is faster than Hamming-window parabolic filtration method, so we conclude that the 3 point derivative method is optimal for 3D FBP. Copyright © 2014. Published by Elsevier Inc.

  18. A FBG pulse wave demodulation method based on PCF modal interference filter

    Science.gov (United States)

    Zhang, Cheng; Xu, Shan; Shen, Ziqi; Zhao, Junfa; Miao, Changyun; Bai, Hua

    2016-10-01

    Fiber optic sensor embedded in textiles has been a new direction of researching smart wearable technology. Pulse signal which is generated by heart beat contains vast amounts of physio-pathological information about the cardiovascular system. Therefore, the research for textile-based fiber optic sensor which can detect pulse wave has far-reaching effects on early discovery and timely treatment of cardiovascular diseases. A novel wavelength demodulation method based on photonic crystal fiber (PCF) modal interference filter is proposed for the purpose of developing FBG pulse wave sensing system embedded in smart clothing. The mechanism of the PCF modal interference and the principle of wavelength demodulation based on In-line Mach-Zehnder interferometer (In-line MZI) are analyzed in theory. The fabricated PCF modal interferometer has the advantages of good repeatability and low temperature sensitivity of 3.5pm/°C from 25°C to 60°C. The designed demodulation system can achieve linear demodulation in the range of 2nm, with the wavelength resolution of 2.2pm and the wavelength sensitivity of 0.055nm-1. The actual experiments' result indicates that the pulse wave can be well detected by this demodulation method, which is in accordance with the commercial demodulation instrument (SM130) and more sensitive than the traditional piezoelectric pulse sensor. This demodulation method provides important references for the research of smart clothing based on fiber grating sensor embedded in textiles and accelerates the developments of wearable fiber optic sensors technology.

  19. High power nano-LiMn2O4 cathode materials with high-rate pulse discharge capability for lithium-ion batteries

    Institute of Scientific and Technical Information of China (English)

    Chen Ying-Chao; Xie Kai; Pan Yi; Zheng Chun-Man; Wang Hua-Lin

    2011-01-01

    Nano-LiMn2O4 cathode materials with nano-sized particles are synthesized via a citric acid assisted sol-gel route. The structure, the morphology and the electrochemical properties of the nano-LiMn2O4 are investigated. Compared with the micro-sized LiMn2O4, the nano-LiMn2O4 possesses a high initial capacity (120 mAh/g) at a discharge rate of 0.2 C (29.6 mA/g). The nano-LiMn2O4 also has a good high-rate discharge capability, retaining 91% of its capacity at a discharge rate of 10 C and 73% at a discharge rate of 40 C. In particular, the nano-LiMn2O4 shows an excellent high-rate pulse discharge capability. The cut-off voltage at the end of 50-ms pulse discharge with a discharge rate of 80 C is above 3.40 V, and the voltage returns to over 4.10 V after the pulse discharge. These results show that the prepared nano-LiMn2O4 could be a potential cathode material for the power sources with the capability to deliver very high-rate pulse currents.

  20. Dynamics of the spatial structure of pulsed discharges in dense gases in point cathode-plane anode gaps and their erosion effect on the plane electrode surface

    Science.gov (United States)

    Baksht, E. Kh.; Blinova, O. M.; Erofeev, M. V.; Karelin, V. I.; Ripenko, V. S.; Tarasenko, V. F.; Trenkin, A. A.; Shibitov, Yu. M.; Shulepov, M. A.

    2016-09-01

    The dynamics of the spatial structure of the plasma of pulsed discharges in air and nitrogen in a nonuniform electric field and their erosion effect on the plane anode surface were studied experimentally. It is established that, at a nanosecond front of the voltage pulse, a diffuse discharge forms in the point cathode-plane anode gap due to the ionization wave propagating from the cathode. As the gap length decreases, the diffuse discharge transforms into a spark. A bright spot on the anode appears during the diffuse discharge, while the spark channel forms in the later discharge stage. The microstructure of autographs of anode spots and spark channels in discharges with durations of several nanoseconds is revealed. The autographs consist of up to 100 and more microcraters 5-100 μm in diameter. It is shown that, due to the short duration of the voltage pulse, a diffuse discharge can be implemented, several pulses of which do not produce appreciable erosion on the plane anode or the soot coating deposited on it.

  1. Effect of substrate bias in nitrogen incorporated amorphous carbon films with embedded nanoparticles deposited by filtered cathodic jet carbon arc technique

    Energy Technology Data Exchange (ETDEWEB)

    Panwar, O.S., E-mail: ospanwar@mail.nplindia.ernet.in [Amorphous and Microcrystalline Silicon Solar Cell Group, Physics of Energy Harvesting Division, National Physical Laboratory (C.S.I.R.), Dr. K.S. Krishnan Road, New Delhi-110012 (India); Kumar, Sushil; Ishpal,; Srivastava, A.K.; Chouksey, Abhilasha; Tripathi, R.K.; Basu, A. [Amorphous and Microcrystalline Silicon Solar Cell Group, Physics of Energy Harvesting Division, National Physical Laboratory (C.S.I.R.), Dr. K.S. Krishnan Road, New Delhi-110012 (India)

    2012-02-15

    Highlights: Black-Right-Pointing-Pointer a-C: N films having nanoparticles were deposited by filtered cathodic jet carbon arc (FCJCA) technique. Black-Right-Pointing-Pointer The effect of negative substrate bias on the properties of a-C: N films embedded with nanoparticles have been studied. Black-Right-Pointing-Pointer The properties of a-C: N films deposited by FCJCA technique have been compared with ta-C: N films deposited by FCVA process. - Abstract: The properties of nitrogen incorporated amorphous carbon (a-C: N) films with embedded nanoparticles, deposited using a filtered cathodic jet carbon arc technique, are reported. X-ray diffraction, high resolution transmission electron microscope and Raman spectroscopy measurements reveal an amorphous structure, but on closer examination the presence of clusters of nanocarbon single crystals with d-spacing close to diamond cubic-phase have also been identified. The effect of substrate bias on the microstructure, conductivity, activation energy, optical band gap, optical constants, residual stress, hardness, elastic modulus, plastic index parameter, percentage elastic recovery and density of states of a-C: N films have been studied and the properties obtained are found to depend on the substrate bias.

  2. Determination of para-arsanilic acid with improved diazotization reaction using differential pulse cathodic stripping voltammetry in aqueous system.

    Science.gov (United States)

    Misni, Marpongahtun; Sathishkumar, Palanivel; Ahamad, Rahmalan; MohdYusoff, Abdull Rahim

    2015-01-01

    Para-arsanilic acid (p-ASA) has been widely used in the poultry industry to promote growth and prevent dysentery. It is excreted unchanged in the manure and released into non-target sites causing organoarsenic pollution risk to the environment and living system. Therefore, simple and effective analytical strategies are demanded for determining the samples that contain p-ASA. However, direct determination of both p-ASA and ortho-arsanilic acid (o-ASA) using differential pulse cathodic stripping voltammetry (DPCSV) gives the similar voltammograms that directly hamper the analysis used by the DPCSV technique. In this study, a method to determine and differentiate p-ASA from o-ASA via diazotization and coupling reaction of the amine groups followed by the direct DPCSV determination of diazo compounds is presented. The diazotization reaction carried out at pH 1.5 and 0 ± 1°C for 10 min showed two reduction peaks in DPCSV at-70 mV and -440 mV vs. Ag/AgCl (KCl 3 M). However, when the diazotization reaction was performed at pH 12.5 and 0 ± 1°C for 40 min, a coloured azo compound was produced and the DPCSV showed only one reduction peak that appeared at -600 mV vs. Ag/AgCl (3 M of KCl). The results of this study show that only p-ASA compound gave a reduction peak, whereas o-ASA compound did not give any peak. The detection limit of p-ASA was found to be 4 × 10(-8 )M. As a result, the proposed electro-analytical technique might be a good candidate to determine and differentiate the p-ASA present in the poultry and environmental samples.

  3. On the trade-off between mainlobe width and peak sidelobe level of mismatched pulse compression filters for linear chirp waveforms

    CSIR Research Space (South Africa)

    Cilliers, Jacques E

    2009-09-01

    Full Text Available In previous paper the authors introduced a technique for generating mismatched pulse compression filters for linear frequency chirp signals. The technique minimizes the sum of the pulse compression sidelobes in an Lp norm sense. It was shown...

  4. Extracting a common pulse like signal from Time Serie using a non linear Kalman Filter

    Science.gov (United States)

    Gazeaux, J.; Batista, D.; Ammann, C.; Naveau, P.; Jégat, C.; Gao, C.

    2009-04-01

    To understand the nature and cause of natural climate variability, it is important to attribute past climate variations to particular forcing factors. In this work, our main focus is to introduce an automatic assimilation procedure to estimate the magnitude of strong but short-lived perturbations, such as large explosive volcanic eruptions, using climate/proxies time series. The extraction and decomposition procedure is run on real multivariate time series of sulfate from ice cores drilled at different sites in Greenland. The sulfate ejected by volcanoes is transported through the stratosphere towards the poles and deposited via sedimentation near the pole. Sulfate in Greenland is then a marker of huge volcanic eruptions which occur all over the world. Such pulse-like processes are highly non linear, as much in time as for their intensity. If they are not detected, such pulse-like signals of extreme and rare events can perturb an objective calculation of the trend. This work is then as much an estimation procedure for such signals, as a first step to estimate a posteriori trend in the time series. Our extraction algorithm handles multivariate time series with a common but unknown forcing. This statistical procedure is based on a multivariate multi-state space model and a non linear Kalman Filter. The non linearity is solved using the calculation of a twice conditional expectation and variance. It can provide an accurate estimate of the timing and duration of individual pulse-like events from a set of different series covering the same temporal space. It not only allows for a more objective estimation of its associated peak amplitude and the subsequent time evolution of the signal, but at the same time it provides a measure of confidence through the posterior probability for each pulse-like event. The flexibility, robustness and limitations of our approach are discussed by applying our method to simulated time series and to the Monte-Carlo method to test the

  5. Hysteresis Current Control Based Shunt Active Power Filter for Six Pulse Ac/Dc Converter

    Directory of Open Access Journals (Sweden)

    Rakesh Kumar Pandey

    2017-02-01

    Full Text Available In this paper the simulation of Shunt Active power Filter using P-Q theory and PI controller has been presented. This SAPF compensates the harmonic currents drawn by three phase six pulse AC/DC converter. The process of compensation is done by calculating the instantaneous reactive power losses using p-q theory and the PI controller to reduce the ripple voltage of the dc capacitor of the PWM-VSI. This approach is different from conventional approach and provides very effective solution. In this simulation we use hysteresis band current controller (HCC for switching the VSI inverter. The simulation has been done for both steady state and transient conditions

  6. Pulse electroanalysis at gold-gold micro-trench electrodes: chemical signal filtering.

    Science.gov (United States)

    Dale, Sara E C; Marken, Frank

    2013-01-01

    Bipotentiostatic control of micro- and nano-trench sensor systems provides new opportunities for enhancing signals (employing feedback currents) and for improved selectivity (by "chemical filtering"). In this study both phenomena are exploited with a gold-gold micro-trench electrode with ca. 70 microm width and ca. 800 microm trench depth. In "generator-collector mode", feedback current enhancement is demonstrated for the hydroquinone/ benzoquinone redox system. Next, a "modulator-sensor mode" experiment is developed in which one electrode potential is stepped into the negative potential region (employing the normal pulse voltammetry method) to induce an oscillating pH change locally in the micro-trench. The resulting shift in the hydroquinone/benzoquinone reversible potential causes a Faradaic sensor signal (employing chronoamperometry). This method provides a "chemical filter" by selecting pH-sensitive redox processes only, and by showing enhanced sensitivity in the region of low buffer capacity. The results for the chemically reversible hydroquinone/benzoquinone system are contrasted to the detection of the chemically irreversible ammonia oxidation.

  7. Improved fission neutron energy discrimination with 4He detectors through pulse filtering

    Science.gov (United States)

    Zhu, Ting; Liang, Yinong; Rolison, Lucas; Barker, Cathleen; Lewis, Jason; Gokhale, Sasmit; Chandra, Rico; Kiff, Scott; Chung, Heejun; Ray, Heather; Baciak, James E.; Enqvist, Andreas; Jordan, Kelly A.

    2017-03-01

    This paper presents experimental and computational techniques implemented for 4He gas scintillation detectors for induced fission neutron detection. Fission neutrons are produced when natural uranium samples are actively interrogated by 2.45 MeV deuterium-deuterium fusion reaction neutrons. Fission neutrons of energies greater than 2.45 MeV can be distinguished by their different scintillation pulse height spectra since 4He detectors retain incident fast neutron energy information. To enable the preferential detection of fast neutrons up to 10 MeV and suppress low-energy event counts, the detector photomultiplier gain is lowered and trigger threshold is increased. Pile-up and other unreliable events due to the interrogating neutron flux and background radiation are filtered out prior to the evaluation of pulse height spectra. With these problem-specific calibrations and data processing, the 4He detector's accuracy at discriminating fission neutrons up to 10 MeV is improved and verified with 252Cf spontaneous fission neutrons. Given the 4He detector's ability to differentiate fast neutron sources, this proof-of-concept active-interrogation measurement demonstrates the potential of special nuclear materials detection using a 4He fast neutron detection system.

  8. Influence of deposition temperature and bias voltage on the crystalline phase of Er{sub 2}O{sub 3} thin films deposited by filtered cathodic arc

    Energy Technology Data Exchange (ETDEWEB)

    Adelhelm, Christoph, E-mail: christoph.adelhelm@ipp.mpg.de [Max-Planck-Institut fuer Plasmaphysik, Materials Research, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany); Pickert, Thomas [Max-Planck-Institut fuer Plasmaphysik, Materials Research, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany); Koch, Freimut, E-mail: freimut.koch@ipp.mpg.de [Max-Planck-Institut fuer Plasmaphysik, Materials Research, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany); Balden, Martin; Jahn, Stephan [Max-Planck-Institut fuer Plasmaphysik, Materials Research, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany); Rinke, Monika [Forschungszentrum Karlsruhe, Institute for Materials Research I, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Maier, Hans [Max-Planck-Institut fuer Plasmaphysik, Materials Research, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany)

    2011-10-01

    Er{sub 2}O{sub 3} thin films on Eurofer steel substrates were produced by a filtered cathodic arc device, varying the substrate temperature (RT - 700 deg. C) and sample bias (0 to -450 V). The crystallographic phase was analyzed by X-ray diffraction and Raman spectroscopy. Deposition at {>=}600 deg. C without bias lead to solely formation of the cubic Er{sub 2}O{sub 3} phase. Thin films of the uncommon, monoclinic B-phase were prepared with a negative bias voltage of {>=}100 V at RT, and at temperatures {<=}500 deg. C for -250 V bias. The B-phase films exhibit a strongly textured film structure. Residual stress measurements show high compressive stress for B-phase films deposited at RT.

  9. Structural, nanomechanical and variable range hopping conduction behavior of nanocrystalline carbon thin films deposited by the ambient environment assisted filtered cathodic jet carbon arc technique

    Energy Technology Data Exchange (ETDEWEB)

    Panwar, O.S., E-mail: ospanwar@mail.nplindia.ernet.in [Polymorphic Carbon Thin Films Group, Physics of Energy Harvesting Division, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi - 110 012 (India); Rawal, Ishpal; Tripathi, R.K. [Polymorphic Carbon Thin Films Group, Physics of Energy Harvesting Division, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi - 110 012 (India); Srivastava, A.K. [Electron and Ion Microscopy, Sophisticated and Analytical Instruments, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi - 110 012 (India); Kumar, Mahesh [Ultrafast Opto-Electronics and Tetrahertz Photonics Group, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi - 110 012 (India)

    2015-04-15

    Highlights: • Nanocrystalline carbon thin films are grown by filtered cathodic jet carbon arc process. • Effect of gaseous environment on the properties of carbon films has been studied. • The structural and nanomechanical properties of carbon thin films have been studied. • The VRH conduction behavior in nanocrystalline carbon thin films has been studied. - Abstract: This paper reports the deposition and characterization of nanocrystalline carbon thin films by filtered cathodic jet carbon arc technique assisted with three different gaseous environments of helium, nitrogen and hydrogen. All the films are nanocrystalline in nature as observed from the high resolution transmission electron microscopic (HRTEM) measurements, which suggests that the nanocrystallites of size ∼10–50 nm are embedded though out the amorphous matrix. X-ray photoelectron spectroscopic studies suggest that the film deposited under the nitrogen gaseous environment has the highest sp{sup 3}/sp{sup 2} ratio accompanied with the highest hardness of ∼18.34 GPa observed from the nanoindentation technique. The film deposited under the helium gaseous environment has the highest ratio of the area under the Raman D peak to G peak (A{sub D}/A{sub G}) and the highest conductivity (∼2.23 S/cm) at room temperature, whereas, the film deposited under the hydrogen environment has the lowest conductivity value (2.27 × 10{sup −7} S/cm). The temperature dependent dc conduction behavior of all the nanocrystalline carbon thin films has been analyzed in the light of Mott’s variable range hopping (VRH) conduction mechanism and observed that all the films obey three dimension VRH conduction mechanism for the charge transport.

  10. Electron transfer processes occurring on platinum neural stimulating electrodes: pulsing experiments for cathodic-first/charge-balanced/biphasic pulses for 0.566 ≤ k ≥ 2.3 in oxygenated and deoxygenated sulfuric acid

    Science.gov (United States)

    Kumsa, Doe W.; Montague, Fred W.; Hudak, Eric M.; Mortimer, J. Thomas

    2016-10-01

    The application of a train of cathodic-first/charge-balanced/biphasic pulses applied to a platinum electrode resulted in a positive creep of the anodic phase potential that increases with increasing charge injection but reaches a steady-state value before 1000 pulses have been delivered. The increase follows from the fact that charge going into irreversible reactions occurring during the anodic phase must equal the charge going into irreversible reactions during the cathodic phase for charge-balanced pulses. In an oxygenated electrolyte the drift of the measured positive potential moved into the platinum oxidation region of the i(V e) profile when the charge injection level exceeds k = 1.75. Platinum dissolution may occur in this region and k = 1.75 defines a boundary between damaging and non-damaging levels on the Shannon Plot. In a very low oxygen environment, the positive potential remained below the platinum oxidation region for the highest charge injection values studied, k = 2.3. The results support the hypothesis that platinum dissolution is the defining factor for the Shannon limit, k = 1.75. Numerous instrumentation issues were encountered in the course of making measurements. The solutions to these issues are provided.

  11. Electron transfer processes occurring on platinum neural stimulating electrodes: pulsing experiments for cathodic-first/charge-balanced/biphasic pulses for 0.566 ≤ k ≤ 2.3 in oxygenated and deoxygenated sulfuric acid.

    Science.gov (United States)

    Kumsa, Doe W; Montague, Fred W; Hudak, Eric M; Mortimer, J Thomas

    2016-10-01

    The application of a train of cathodic-first/charge-balanced/biphasic pulses applied to a platinum electrode resulted in a positive creep of the anodic phase potential that increases with increasing charge injection but reaches a steady-state value before 1000 pulses have been delivered. The increase follows from the fact that charge going into irreversible reactions occurring during the anodic phase must equal the charge going into irreversible reactions during the cathodic phase for charge-balanced pulses. In an oxygenated electrolyte the drift of the measured positive potential moved into the platinum oxidation region of the i(V e) profile when the charge injection level exceeds k = 1.75. Platinum dissolution may occur in this region and k = 1.75 defines a boundary between damaging and non-damaging levels on the Shannon Plot. In a very low oxygen environment, the positive potential remained below the platinum oxidation region for the highest charge injection values studied, k = 2.3. The results support the hypothesis that platinum dissolution is the defining factor for the Shannon limit, k = 1.75. Numerous instrumentation issues were encountered in the course of making measurements. The solutions to these issues are provided.

  12. Comparison of Performance Metrics for QPSK and OQPSK Transmission Using Root Raised Cosine and Raised Cosine Pulse shaping Filters for Applications in Mobile Communication

    CERN Document Server

    Chattopadhyay, Sudipta

    2009-01-01

    Quadrature Phase Shift Keying (QPSK) and Offset Quadrature Phase Shift Keying (OQPSK) are two well accepted modulation techniques used in Code Division Multiple Access (CDMA) system. The Pulse Shaping Filters play an important role in digital transmission. The type of Pulse Shaping Filter used, and its behavior would influence the performance of the communication system. This in turn, would have an effect on the performance of the Mobile Communication system, in which the digital communication technique has been employed. In this paper we have presented comparative study of some performance parameters or performance metrics of a digital communication system like, Error Vector Magnitude (EVM), Magnitude Error, Phase Error and Bandwidth Efficiency for a QPSK transmission system. Root Raised Cosine (RRC) and Raised Cosine (RC) Pulse shaping filters have been used for comparison. The measurement results serve as a guideline to the system designer to select the proper pulse shaping filter with the appropriate valu...

  13. Phase transitions of doped carbon in CrCN coatings with modified mechanical and tribological properties via filtered cathodic vacuum arc deposition

    Science.gov (United States)

    Guan, J. J.; Wang, H. Q.; Qin, L. Z.; Liao, B.; Liang, H.; Li, B.

    2017-04-01

    The CrCN coatings were fabricated onto Si (1 1 1) wafers and SUS304 stainless steel plates using filtered cathodic vacuum arc deposition (FCVAD) technique under different flow ratios of N2/C2H2 gas mixture. The morphology, crystalline structure and chemical composition of the coatings were characterized. It was found that the grain size reduce with increasing carbon content, which makes the CrCN coatings refined and smooth. The quasi-one-dimensional carbolite phase was also found in CrN host lattice with C2H2 content ranging from 5% to 20%, and it will be evolved into amorphous carbon and amorphous CNx phases as C2H2 content exceeds 20%. Moreover, we examined the mechanical and tribological properties of the CrCN coatings, and the experimental results confirmed that the friction coefficient of the coatings descend to the lowest value as 0.39 with 30% C2H2 content, due to the graphite (sp2 Csbnd C) phase embed in CrN host lattice; while the chromium carbon (Cr3C2) and diamond (sp3 Csbnd C) phases may give rise to the increase of the coating hardness with the highest value at 23.97 GPa under 20% C2H2 content.

  14. Effect of modulation periods on the microstructure and mechanical properties of DLC/TiC multilayer films deposited by filtered cathodic vacuum arc method

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Zhaoying [Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, Sichuan (China); State Key Laboratory of Vanadium and Titanium Resources Comprehensive Utilization, Pangang Group Research Institute Co., Ltd., Panzhihua 617000, Sichuan (China); Sun, H. [Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, Sichuan (China); Leng, Y.X., E-mail: yxleng@263.net [Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, Sichuan (China); Li, Xueyuan; Yang, Wenmao [Institute of Mechanical Manufacturing Technology, China Academy of Engineering Physics, Mianyang 621900, Sichuan (China); Huang, N. [Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, Sichuan (China)

    2015-02-15

    Highlights: • DLC/TiC multilayer films with different modulation periods at same modulation ratio 1:1 were deposited by FCVA. • The residual stress of DLC/TiC multilayer films decreases with the modulation periods decrease. • The hardness of the multilayer DLC films decreases with modulation periods increasing. - Abstract: The high stress of diamond-like carbon (DLC) film limits its thickness and adhesion on substrate. Multilayer structure is one approach to overcome this disadvantage. In this paper, the DLC/TiC multilayer films with different modulation periods (80 nm, 106 nm or 160 nm) at same modulation ratio of 1:1 were deposited on Si(1 0 0) wafer and Ti-6Al-4V substrate by filtered cathodic vacuum arc (FCVA) technology. X-ray diffraction (XRD), transmission electron microscopy (TEM), nanoindention and wear test were employed to investigate the effect of modulation periods on the microstructure and mechanical properties of the multilayer films. The results showed that the residual stress of the DLC/TiC multilayer films could be effectively reduced and the residual stress decreased with the modulation periods decreasing. The hardness of the DLC/TiC multilayer films increased with modulation periods decreasing. The DLC/TiC multilayer film with modulation period of 106 nm had the best wear resistance due to the good combination of hardness, ductility and low compressive stress.

  15. Incidence Angle Effect of Energetic Carbon Ions on Deposition Rate, Topography, and Structure of Ultrathin Amorphous Carbon Films Deposited by Filtered Cathodic Vacuum Arc

    KAUST Repository

    Wang, N.

    2012-07-01

    The effect of the incidence angle of energetic carbon ions on the thickness, topography, and structure of ultrathin amorphous carbon (a-C) films synthesized by filtered cathodic vacuum arc (FCVA) was examined in the context of numerical and experimental results. The thickness of a-C films deposited at different incidence angles was investigated in the light of Monte Carlo simulations, and the calculated depth profiles were compared with those obtained from high-resolution transmission electron microscopy (TEM). The topography and structure of the a-C films were studied by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS), respectively. The film thickness decreased with the increase of the incidence angle, while the surface roughness increased and the content of tetrahedral carbon hybridization (sp 3) decreased significantly with the increase of the incidence angle above 45° , measured from the surface normal. TEM, AFM, and XPS results indicate that the smoothest and thinnest a-C films with the highest content of sp 3 carbon bonding were produced for an incidence angle of 45°. The findings of this study have direct implications in ultrahigh-density magnetic recording, where ultrathin and smooth a-C films with high sp 3 contents are of critical importance. © 2012 IEEE.

  16. Speckle Reduction for Ultrasonic Imaging Using Frequency Compounding and Despeckling Filters along with Coded Excitation and Pulse Compression

    Directory of Open Access Journals (Sweden)

    Joshua S. Ullom

    2012-01-01

    Full Text Available A method for improving the contrast-to-noise ratio (CNR while maintaining the −6 dB axial resolution of ultrasonic B-mode images is proposed. The technique proposed is known as eREC-FC, which enhances a recently developed REC-FC technique. REC-FC is a combination of the coded excitation technique known as resolution enhancement compression (REC and the speckle-reduction technique frequency compounding (FC. In REC-FC, image CNR is improved but at the expense of a reduction in axial resolution. However, by compounding various REC-FC images made from various subband widths, the tradeoff between axial resolution and CNR enhancement can be extended. Further improvements in CNR can be obtained by applying postprocessing despeckling filters to the eREC-FC B-mode images. The despeckling filters evaluated were the following: median, Lee, homogeneous mask area, geometric, and speckle-reducing anisotropic diffusion (SRAD. Simulations and experimental measurements were conducted with a single-element transducer (f/2.66 having a center frequency of 2.25 MHz and a −3 dB bandwidth of 50%. In simulations and experiments, the eREC-FC technique resulted in the same axial resolution that would be typically observed with conventional excitation with a pulse. Moreover, increases in CNR of 348% were obtained in experiments when comparing eREC-FC with a Lee filter to conventional pulsing methods.

  17. Effect of pulsed bias on the properties of ZrN/TiZrN films deposited by a cathodic vacuum arc

    Institute of Scientific and Technical Information of China (English)

    Zhang Guo-Ping; Wang Xing-Quan; Lü Guo-Hua; Zhou Lan; Huang Jun; Chen Wei; Yang Si-Ze

    2013-01-01

    .ZrN/TiZrN multilayers are deposited by using the cathodic vacuum arc method with different substrate bias (from 0 to-800 V),using Ti and Zr plasma flows in residual N2 atmosphere,combined with ion bombardment of sample surfaces.The effect of pulsed bias on the structure and properties of films is investigated.Microstructure of the coating is analyzed by X-ray diffraction (XRD),and scanning electron microscopy (SEM).In addition,nanohardness,Young's modulus,and scratch tests are performed.The experimental results show that the films exhibit a nanoscale multilayer structure consisting of TiZrN and ZrN phases.Solid solutions are formed for component TiZrN films.The dominant preferred orientation of TiZrN films is (111) and (220).At a pulsed bias of-200 V,the nanohardness and the adhesion strength of the ZrN/TiZrN multilayer reach a maximum of 38 GPa,and 78 N,respectively.The ZrN/TiZrN multilayer demonstrates an enhanced nanohardness compared with binary TiN and ZrN films deposited under equivalent conditions.

  18. [High current microsecond pulsed hollow cathode lamp excited ionic fluorescence spectrometry of alkaline earth elements in inductively coupled plasma with a Fassel-torch].

    Science.gov (United States)

    Zhang, Shao-Yu; Gong, Zhen-Bin; Huang, Ben-Li

    2006-02-01

    High current microsecond pulsed hollow cathode lamp (HCMP-HCL) excited ionic fluorescence spectrometry (IFS) of alkaline earth elements in inductively coupled plasma (ICP) with a Fassel-torch has been investigated. In wide condition ranges only IFS was observed, whilst atomic fluorescence spectrometry (AFS) was not detectable. More intense ionic fluorescence signal was observed at lower observation heights and at lower incident RF powers. Without introduction of any reduction organic gases into the ICP, the limit of detection (LOD, 3sigma) of Ba was improved by 50-fold over that of a conventional pulsed (CP) HCL with the Baird sleeve-extended torch. For Ca and Sr, the LODs by HCMP-HCL-ICP-IFS and CP-HCL-ICP-AFS show no significant difference. Relative standard deviations were 0.6%-1.4% (0.1-0.2 microg x mL(-1), n = 10) for 5 ionic fluorescence lines. Preliminary studies showed that the intensity of ionic fluorescence could be depressed in the presence of K, Al and P.

  19. Growth feature of ionic nitrogen doped CN{sub x} bilayer films with Ti and TiN interlayer by pulse cathode arc discharge

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Bing, E-mail: zhoubing@tyut.edu.cn [Research Institute of Surface Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Liu, Zhubo [Research Institute of Surface Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Piliptsou, D.G., E-mail: pdg_@mail.ru [International Chinese–Belarusian Scientific Laboratory on Vacuum-Plasma Technology, Francisk Skorina Gomel State University, Gomel 246019 (Belarus); Nanjing University of Science and Technology, Nanjing 210094 (China); Rogachev, A.V. [International Chinese–Belarusian Scientific Laboratory on Vacuum-Plasma Technology, Francisk Skorina Gomel State University, Gomel 246019 (Belarus); Nanjing University of Science and Technology, Nanjing 210094 (China); Yu, Shengwang; Wu, Yanxia; Tang, Bin [Research Institute of Surface Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Rudenkov, A.S. [International Chinese–Belarusian Scientific Laboratory on Vacuum-Plasma Technology, Francisk Skorina Gomel State University, Gomel 246019 (Belarus); Nanjing University of Science and Technology, Nanjing 210094 (China)

    2016-01-15

    Graphical abstract: - Highlights: • Ti/ and TiN/CN{sub x} (N{sup +}) bilayers are prepared at various frequencies by pulse cathode arc. • Ti interlayer facilitates the introduction of N atoms into the CN{sub x} (N{sup +}) films. • The most N-sp{sup 2}C bonds (mainly graphite-like N) present in the TiN/CN{sub x} (N{sup +}, 3 Hz) film. • Ti/CN{sub x} (N{sup +}, 3 Hz) bilayer possesses small size and disordering of Csp{sup 2} clusters. • The higher hardness and the lower stress presents in the TiN/CN{sub x} (N{sup +}, 10 Hz) bilayer. - Abstract: Using nano-scaled Ti and TiN as interlayer, ionic nitrogen doped carbon (CN{sub x} (N{sup +})) bilayer films were prepared at various pulse frequencies by cathode arc technique. Elemental distribution at the interface, bonding compositions, microstructure, and mechanical properties of CN{sub x} (N{sup +}) bilayer films were investigated in dependence of interlayer and pulse frequency by Auger electron spectroscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, nanoindentation, and surface profilometer. The results showed that the diffusion extent of C atoms at the interface of CN{sub x} (N{sup +}) bilayers is higher than for the α-C and CN{sub x} (N{sub 2}) bilayers with the same interlayer. Nitrogen atoms could diffuse throughout the pre-deposited Ti and TiN layers into the Si substrate for all CN{sub x} (N{sup +}) bilayers. Ti interlayer facilitates the introduction of N atoms into the CN{sub x} (N{sup +}) films and exhibits a certain catalytic effect on the coordination of N atoms with sp{sup 2}- and sp{sup 3}-C binding. More nitrogenated and intense CN bonding configurations (mainly graphite-like N) form in the TiN/CN{sub x} (N{sup +}) bilayer. Ti/CN{sub x} (N{sup +}) bilayer prepared at low frequency possesses small size and disordering of Csp{sup 2} clusters but TiN interlayer weakens the formation of Csp{sup 2} bonding and increases the disordering of Csp{sup 2} clusters in the films. The residual

  20. An Active Trap Filter for Switching Harmonics Attenuation of Low-Pulse-Ratio Inverters

    DEFF Research Database (Denmark)

    Bai, Haofeng; Wang, Xiongfei; Loh, Poh Chiang

    2017-01-01

    , but generally susceptible to filter parameter variations and harmonic resonances. This paper hence presents an alternative Active Trap Filter (ATF), based on a series-LC-filtered inverter, for attenuating switching harmonics in a flexible, while yet not cost burdensome, approach. A direct impedance synthesis...... method has also been proposed for the ATF to better enforce its active switching harmonic bypassing ability. Compared with conventional schemes for controlling active power filters, the proposed method is more readily implemented, since it requires neither current reference generation nor high......-bandwidth current control loop. Moreover, the use of a series LC-filter at its ac-side helps the ATF to reduce its inverter voltage and power ratings. Compensated frequency range of the ATF can hence be enlarged by using a comparably higher switching frequency and a proper step-by-step design procedure...

  1. Performance analysis of linear bandpass filter and pulse inversion in separating subharmonic frequency of signals from ultrasound contrast agent

    Directory of Open Access Journals (Sweden)

    Chinda Samakee

    2012-12-01

    Full Text Available Recently, many publications reported the generation of subharmonic frequency (f0/2 and its potential use in imagingfrom ultrasound contrast agent (UCA. Subharmonic imaging (SHI has provided better contrast resolution over the secondharmonic signals due to the lack of subharmonic generation in the tissue region. However, subharmonic separation in SHIutilizes linear bandpass filtering only. In this paper, we compare the subharmonic separation capability of linear band filter(LBF, pulse inversion (PI, and their combination (PILBF based on contrast-to-tissue ratio (CTR. Results show that theCTR values from the LBF, the PI, and the PILBF are 20.30, 40.30, and 52.74 dB, respectively. The optimal stopband attenuation and fractional bandwidth for the PILBF method are 50 dB and 10%, respectively. This high CTR value indicates thefeasibility of the PILBF method in creating high quality ultrasound image from subharmonic frequency.

  2. FLOW CHARACTERISTICS OF WALL-FLOW DIESEL PARTICULATE FILTER SYSTEM WITH REVERSE PULSE AIR REGENERATION

    Institute of Scientific and Technical Information of China (English)

    Yao Chunde; Shao Yuping; Zhang Chunrun; Zi XinYun; Jiang Dahai; Deng Chenglin

    2005-01-01

    To simulate steady airflows inside of wall-flow diesel particulate filters (DPF) with different reverse blowing pipes collocation, a mathematical model of the flow in a DPF is established by an equivalent continuum approach. The experimental results agree well with the theoretical values calculated from the model. Simulation shows that the velocity and the pressure distribution of the filters in the regenerative process are key factors to the filter's regeneration. How to decrease the mal-distribution of the flow in the filter and how to achieve the better regenerative performance at the least cost of air consumption in the regenerative process are the ultimate goals of the study. Calculation and experiments show that the goals can be realized through adjusting the angle of two reverse blowing pipes and their relative location suitably.

  3. Application of wavelet filtering and Barker-coded pulse compression hybrid method to air-coupled ultrasonic testing

    Science.gov (United States)

    Zhou, Zhenggan; Ma, Baoquan; Jiang, Jingtao; Yu, Guang; Liu, Kui; Zhang, Dongmei; Liu, Weiping

    2014-10-01

    Air-coupled ultrasonic testing (ACUT) technique has been viewed as a viable solution in defect detection of advanced composites used in aerospace and aviation industries. However, the giant mismatch of acoustic impedance in air-solid interface makes the transmission efficiency of ultrasound low, and leads to poor signal-to-noise (SNR) ratio of received signal. The utilisation of signal-processing techniques in non-destructive testing is highly appreciated. This paper presents a wavelet filtering and phase-coded pulse compression hybrid method to improve the SNR and output power of received signal. The wavelet transform is utilised to filter insignificant components from noisy ultrasonic signal, and pulse compression process is used to improve the power of correlated signal based on cross-correction algorithm. For the purpose of reasonable parameter selection, different families of wavelets (Daubechies, Symlet and Coiflet) and decomposition level in discrete wavelet transform are analysed, different Barker codes (5-13 bits) are also analysed to acquire higher main-to-side lobe ratio. The performance of the hybrid method was verified in a honeycomb composite sample. Experimental results demonstrated that the proposed method is very efficient in improving the SNR and signal strength. The applicability of the proposed method seems to be a very promising tool to evaluate the integrity of high ultrasound attenuation composite materials using the ACUT.

  4. Effect of oxygen incorporation on the structure and elasticity of Ti-Al-O-N coatings synthesized by cathodic arc and high power pulsed magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Hans, M., E-mail: hans@mch.rwth-aachen.de; Baben, M. to; Music, D.; Ebenhöch, J.; Schneider, J. M. [Materials Chemistry, RWTH Aachen University, Kopernikusstr. 10, D-52074 Aachen (Germany); Primetzhofer, D. [Department of Physics and Astronomy, Uppsala University, Lägerhyddsvägen 1, S-75120 Uppsala (Sweden); Kurapov, D.; Arndt, M.; Rudigier, H. [Oerlikon Balzers Coating AG, Iramali 18, LI-9496 Balzers, Principality of Liechtenstein (Liechtenstein)

    2014-09-07

    Ti-Al-O-N coatings were synthesized by cathodic arc and high power pulsed magnetron sputtering. The chemical composition of the coatings was determined by means of elastic recoil detection analysis and energy dispersive X-ray spectroscopy. The effect of oxygen incorporation on the stress-free lattice parameters and Young's moduli of Ti-Al-O-N coatings was investigated by X-ray diffraction and nanoindentation, respectively. As nitrogen is substituted by oxygen, implications for the charge balance may be expected. A reduction in equilibrium volume with increasing O concentration is identified by X-ray diffraction and density functional theory calculations of Ti-Al-O-N supercells reveal the concomitant formation of metal vacancies. Hence, the oxygen incorporation-induced formation of metal vacancies enables charge balancing. Furthermore, nanoindentation experiments reveal a decrease in elastic modulus with increasing O concentration. Based on ab initio data, two causes can be identified for this: First, the metal vacancy-induced reduction in elasticity; and second, the formation of, compared to the corresponding metal nitride bonds, relatively weak Ti-O and Al-O bonds.

  5. Pulse

    Science.gov (United States)

    ... resting for at least 10 minutes. Take the exercise heart rate while you are exercising. ... pulse rate can help determine if the person's heart is pumping. Pulse ... rate gives information about your fitness level and health.

  6. Note: radio frequency inductance-capacitance band-stop filter circuit to perform contactless conductivity measurements in pulsed magnetic fields.

    Science.gov (United States)

    Altarawneh, M M

    2012-09-01

    We present a new technique to perform radio frequency (rf) contactless conductivity measurements in pulsed magnetic fields to probe different ground states in condensed matter physics. The new method utilizes a simple analog band-stop filter circuit implemented in a radio frequency transmission setup to perform contactless conductivity measurements. The new method is more sensitive than the other methods (e.g., the tunnel diode oscillator and the proximity detector oscillator) due to more sensitive dependence of the circuit resonance frequency on the tank circuit inductance (not the transmission line). More important, the new method is more robust than other methods when used to perform measurements in very high magnetic fields, works for a wide range of temperatures (i.e., 300 K-1.4 K) and is less sensitive to noise and mechanical vibrations during pulse magnet operation. The new technique was successfully applied to measure the Shubnikov-de Haas effect in Bi(2)Se(3) in pulsed magnetic fields of up to 60 T.

  7. Cathodic adsorptive stripping voltammetry of drotaverine hydrochloride and its determination in tablets and human urine by differential pulse voltammetry.

    Science.gov (United States)

    Zayed, S I M; Issa, Y M

    2009-04-01

    The stripping voltammetric behaviour of drotaverine hydrochloride (DvCl) was studied using a hanging mercury drop electrode (HMDE). The adsorptive stripping response has been evaluated with respect to pH, accumulation time, accumulation potential, scan rate and other variables. Differential pulse DP mode; over the potential range -400 to -1200 mV, is used in the presence of 0.04 M Britton-Robinson buffer pH 2. Cyclic voltammetric study indicates that the reduction process is irreversible and controlled by adsorption. The response of DP technique is linear over the concentration range 21.70-257.34 ng/ml. Limit of detection and limit of quantification were 3.15 and 10.50 ng/ml, respectively. The proposed method was successfully applied for the determination of the drug in commercial tablets and spiked human urine samples.

  8. The Inlfuence of Anode Distance on the Depth of Pulse Current Cathodic Protection%阳极距离对脉冲电流阴极保护深度的影响

    Institute of Scientific and Technical Information of China (English)

    周好斌; 张涛; 许庆

    2015-01-01

    目的 研究阳极距离对脉冲电流阴极保护深度的影响.方法:在5.0×0.5×0.5m的水池中,建立均匀NaCl溶液介质模拟油井套管阴极保护体系,采用挂片法,研究了阳极距离对方波脉冲电流阴极保护深度的影响.结果:在阴极保护系统中,阴阳极距离存在一个临界值D临,只有阴阳极距离大于D临时,阴极才有可能全线得到有效保护.结论 在脉冲电流阴极保护系统中,阳极距离是影响保护深度的重要因素.如果由于现场条件限制,阳极不可能分布得足够远,那么需采用别的办法来增加保护深度.%Objective to study the influence of anode distance on the depth of pulse current cathodic protection. Method in 5.0×0.5×0.5 pool, establish uniform medium NaCl solution simulated cathodic protection system, by using bolt, anode distance each other wave pulse current cathodic protection is studied the influence of the depth. Results In the cathodic protection system, there exists a critical value D polar distance of cathode and anode is only temporary, anode distance is greater than the D cathode could all be effectively protected. Conclusion in the current cathodic protection system, the anode distance is an important factor to impact protection depth. If the site conditions, anode distribution could not far enough, so need to use other ways to increase the protection depth.

  9. An Efficient Space Vector Pulse Width Modulation with BFO Based Self Tuning PI Controller for Shunt Active Power Filter

    Directory of Open Access Journals (Sweden)

    P. Saravanan

    2014-05-01

    Full Text Available This research study mainly focuses on using an efficient control strategy for extracting reference currents of shunt active filters under non linear load conditions. In recent decades, the utilization of highly automatic electric equipments has resulted in enormous economic loss. Thus, the power suppliers as well as the power consumers are very much concerned about the power quality issues and compensation approaches. In order to deal with this issue, Active Power Filter (APF has been considered as an attractive solution due to its significant harmonic compensation. But, the performance of APF is not consistent and is varies based on the output of the controller techniques. An efficient (id-id control strategy is used in this approach for attaining utmost profit from grid-interfacing inverters installed in transmission systems. The voltages are controlled through the PI controller which is further tuned by an optimization approach. Bacterial Forge Optimization (BFO is used in this approach for tuning the PI controller for the optimal value. The inverter used in this approach can be considered as a Shunt Active Power Filter (SAPF to compensate non linear load current harmonics. In order to improve the overall performance of the system, Space Vector Pulse Width Modulation (SVPWM is used in this proposed approach which regulates power frequency and produces good circularity through DC-AC part. SVPWM also eliminates the 3rd order harmonics and minimizes the 5th order harmonics effectively. The integration of (id-id control strategy and SVPWM has been proposed in this research study. Simulation results are carried out in MATLAB/Simulink and the performance of the proposed approach is compared with other control strategies. This research studies shows unique approach for attaining maximum benefits from RES with suppression of current harmonics.

  10. Processing of pulse oximeter signals using adaptive filtering and autocorrelation to isolate perfusion and oxygenation components

    Science.gov (United States)

    Ibey, Bennett; Subramanian, Hariharan; Ericson, Nance; Xu, Weijian; Wilson, Mark; Cote, Gerard L.

    2005-03-01

    A blood perfusion and oxygenation sensor has been developed for in situ monitoring of transplanted organs. In processing in situ data, motion artifacts due to increased perfusion can create invalid oxygenation saturation values. In order to remove the unwanted artifacts from the pulsatile signal, adaptive filtering was employed using a third wavelength source centered at 810nm as a reference signal. The 810 nm source resides approximately at the isosbestic point in the hemoglobin absorption curve where the absorbance of light is nearly equal for oxygenated and deoxygenated hemoglobin. Using an autocorrelation based algorithm oxygenation saturation values can be obtained without the need for large sampling data sets allowing for near real-time processing. This technique has been shown to be more reliable than traditional techniques and proven to adequately improve the measurement of oxygenation values in varying perfusion states.

  11. Pulse shape discrimination of Cs2LiYCl6:Ce3+ detectors at high count rate based on triangular and trapezoidal filters

    Science.gov (United States)

    Wen, Xianfei; Enqvist, Andreas

    2017-09-01

    Cs2LiYCl6:Ce3+ (CLYC) detectors have demonstrated the capability to simultaneously detect γ-rays and thermal and fast neutrons with medium energy resolution, reasonable detection efficiency, and substantially high pulse shape discrimination performance. A disadvantage of CLYC detectors is the long scintillation decay times, which causes pulse pile-up at moderate input count rate. Pulse processing algorithms were developed based on triangular and trapezoidal filters to discriminate between neutrons and γ-rays at high count rate. The algorithms were first tested using low-rate data. They exhibit a pulse-shape discrimination performance comparable to that of the charge comparison method, at low rate. Then, they were evaluated at high count rate. Neutrons and γ-rays were adequately identified with high throughput at rates of up to 375 kcps. The algorithm developed using the triangular filter exhibits discrimination capability marginally higher than that of the trapezoidal filter based algorithm irrespective of low or high rate. The algorithms exhibit low computational complexity and are executable on an FPGA in real-time. They are also suitable for application to other radiation detectors whose pulses are piled-up at high rate owing to long scintillation decay times.

  12. Nanotube cathodes.

    Energy Technology Data Exchange (ETDEWEB)

    Overmyer, Donald L.; Lockner, Thomas Ramsbeck; Siegal, Michael P.; Miller, Paul Albert

    2006-11-01

    Carbon nanotubes have shown promise for applications in many diverse areas of technology. In this report we describe our efforts to develop high-current cathodes from a variety of nanotubes deposited under a variety of conditions. Our goal was to develop a one-inch-diameter cathode capable of emitting 10 amperes of electron current for one second with an applied potential of 50 kV. This combination of current and pulse duration significantly exceeds previously reported nanotube-cathode performance. This project was planned for two years duration. In the first year, we tested the electron-emission characteristics of nanotube arrays fabricated under a variety of conditions. In the second year, we planned to select the best processing conditions, to fabricate larger cathode samples, and to test them on a high-power relativistic electron beam generator. In the first year, much effort was made to control nanotube arrays in terms of nanotube diameter and average spacing apart. When the project began, we believed that nanotubes approximately 10 nm in diameter would yield sufficient electron emission properties, based on the work of others in the field. Therefore, much of our focus was placed on measured field emission from such nanotubes grown on a variety of metallized surfaces and with varying average spacing between individual nanotubes. We easily reproduced the field emission properties typically measured by others from multi-wall carbon nanotube arrays. Interestingly, we did this without having the helpful vertical alignment to enhance emission; our nanotubes were randomly oriented. The good emission was most likely possible due to the improved crystallinity, and therefore, electrical conductivity, of our nanotubes compared to those in the literature. However, toward the end of the project, we learned that while these 10-nm-diameter CNTs had superior crystalline structure to the work of others studying field emission from multi-wall CNT arrays, these nanotubes still

  13. Determination of eye safety filter protection factors associated with retinal thermal hazard and blue light photochemical hazard for intense pulsed light sources

    Energy Technology Data Exchange (ETDEWEB)

    Clarkson, D McG [Department of Clinical Physics and Bioengineering, Arden Cancer Centre, Walsgrave Hospital, UHCW NHS Trust, Coventry, CV2 2DX (United Kingdom)

    2006-02-21

    An assessment is provided of protection factors afforded for retinal thermal hazard and blue light photochemical hazard for a range of filters used with intense pulsed light sources (IPLs). A characteristic IPL spectrum based on black body radiation at 5000 K with a low cut filter at 515 nm was identified as suitable for such estimations. Specific filters assessed included types with idealized transmission properties and also a range of types whose transmission characteristics were measured by means of a Bentham DMc150 spectroradiometer. Predicted behaviour based on these spectra is outlined which describes both the effectiveness of protection and the level of luminous transmittance afforded. The analysis showed it was possible to describe a figure of merit for a particular filter material relating the degree of protection provided and corresponding value of luminous transmittance. This consideration is important for providing users of IPL equipment with safety eyewear with adequate level of visual transmittance. (note)

  14. Realisation and advanced engineering of true optical rugate filters based on nanoporous anodic alumina by sinusoidal pulse anodisation

    Science.gov (United States)

    Santos, Abel; Yoo, Jeong Ha; Rohatgi, Charu Vashisth; Kumeria, Tushar; Wang, Ye; Losic, Dusan

    2016-01-01

    This study is the first realisation of true optical rugate filters (RFs) based on nanoporous anodic alumina (NAA) by sinusoidal waves. An innovative and rationally designed sinusoidal pulse anodisation (SPA) approach in galvanostatic mode is used with the aim of engineering the effective medium of NAA in a sinusoidal fashion. A precise control over the different anodisation parameters (i.e. anodisation period, anodisation amplitude, anodisation offset, number of pulses, anodisation temperature and pore widening time) makes it possible to engineer the characteristic reflection peaks and interferometric colours of NAA-RFs, which can be finely tuned across the UV-visible-NIR spectrum. The effect of the aforementioned anodisation parameters on the photonic properties of NAA-RFs (i.e. characteristic reflection peaks and interferometric colours) is systematically assessed in order to establish for the first time a comprehensive rationale towards NAA-RFs with fully controllable photonic properties. The experimental results are correlated with a theoretical model (Looyenga-Landau-Lifshitz - LLL), demonstrating that the effective medium of these photonic nanostructures can be precisely described by the effective medium approximation. NAA-RFs are also demonstrated as chemically selective photonic platforms combined with reflectometric interference spectroscopy (RIfS). The resulting optical sensing system is used to assess the reversible binding affinity between a model drug (i.e. indomethacin) and human serum albumin (HSA) in real-time. Our results demonstrate that this system can be used to determine the overall pharmacokinetic profile of drugs, which is a critical aspect to be considered for the implementation of efficient medical therapies.This study is the first realisation of true optical rugate filters (RFs) based on nanoporous anodic alumina (NAA) by sinusoidal waves. An innovative and rationally designed sinusoidal pulse anodisation (SPA) approach in galvanostatic

  15. Realisation and advanced engineering of true optical rugate filters based on nanoporous anodic alumina by sinusoidal pulse anodisation.

    Science.gov (United States)

    Santos, Abel; Yoo, Jeong Ha; Rohatgi, Charu Vashisth; Kumeria, Tushar; Wang, Ye; Losic, Dusan

    2016-01-21

    This study is the first realisation of true optical rugate filters (RFs) based on nanoporous anodic alumina (NAA) by sinusoidal waves. An innovative and rationally designed sinusoidal pulse anodisation (SPA) approach in galvanostatic mode is used with the aim of engineering the effective medium of NAA in a sinusoidal fashion. A precise control over the different anodisation parameters (i.e. anodisation period, anodisation amplitude, anodisation offset, number of pulses, anodisation temperature and pore widening time) makes it possible to engineer the characteristic reflection peaks and interferometric colours of NAA-RFs, which can be finely tuned across the UV-visible-NIR spectrum. The effect of the aforementioned anodisation parameters on the photonic properties of NAA-RFs (i.e. characteristic reflection peaks and interferometric colours) is systematically assessed in order to establish for the first time a comprehensive rationale towards NAA-RFs with fully controllable photonic properties. The experimental results are correlated with a theoretical model (Looyenga-Landau-Lifshitz - LLL), demonstrating that the effective medium of these photonic nanostructures can be precisely described by the effective medium approximation. NAA-RFs are also demonstrated as chemically selective photonic platforms combined with reflectometric interference spectroscopy (RIfS). The resulting optical sensing system is used to assess the reversible binding affinity between a model drug (i.e. indomethacin) and human serum albumin (HSA) in real-time. Our results demonstrate that this system can be used to determine the overall pharmacokinetic profile of drugs, which is a critical aspect to be considered for the implementation of efficient medical therapies.

  16. Experimental study of cake formation on heat treated and membrane coated needle felts in a pilot scale pulse jet bag filter using optical in-situ cake height measurement

    OpenAIRE

    Saleem, Mahmood; Khan, Rafi Ullah; Tahir, M. Suleman; Krammer, Gernot

    2011-01-01

    Pulse-jet bag filters are frequently employed for particle removal from off gases. Separated solids form a layer on the permeable filter media called filter cake. The cake is responsible for increasing pressure drop. Therefore, the cake has to be detached at a predefined upper pressure drop limit or at predefined time intervals. Thus the process is intrinsically semi-continuous. The cake formation and cake detachment are interdependent and may influence the performance of the filter. Therefor...

  17. Operation Behavior of a Multi-Candle Filter with Coupled Pressure Pulse Recleaning during Normal Operation and in the Case of a Filter Candle Failure

    Energy Technology Data Exchange (ETDEWEB)

    Mai, R.; Leibold, H. Seifert, H.; Heidenreich, S.; Haag, W.

    2002-09-18

    A pilot filter with the CPP recleaning system was installed and commissioned during the first half year of 2000 in ''PYDRA'', the pyrolytic rotary tube facility of the Institute for Technical Chemistry, Research Center Karlsruhe. The filter, with a rated throughput of 50 std.m{sup 3}/h, is equipped with two clusters of three filter candles each (DIA-SCHUMALITH{reg_sign} T 10-20, 1 = 1500 mm), and has been designed for a maximum operating temperature of 550 C. After commissioning, the filter was run in the stand-alone mode, first without pyrolysis, to filter sticky inorganic dust of the type which can arise in waste incineration in the temperature range above 400 C.

  18. Plasma distribution of cathodic ARC deposition system

    Energy Technology Data Exchange (ETDEWEB)

    Anders, S.; Raoux, S.; Krishnan, K.; MacGill, R.A.; Brown, I.G. [Lawrence Berkeley National Lab., CA (United States)

    1996-08-01

    The plasma distribution using a cathodic arc plasma source with and without magnetic macroparticle filter has been determined by depositing on a transparent plastic substrate and measuring the film absorption. It was found that the width of the distribution depends on the arc current, and it also depends on the cathode material which leads to a spatial separation of the elements when an alloy cathode is used. By applying a magnetic multicusp field near the exit of the magnetic filter, it was possible to modify the plasma distribution and obtain a flat plasma profile with a constant and homogeneous elemental distribution.

  19. Influence of intrapulse Raman scattering on the stationary pulses in the presence of linear and nonlinear gain as well as spectral filtering

    Science.gov (United States)

    Uzunov, Ivan M.; Georgiev, Zhivko D.; Arabadzhev, Todor N.

    2015-01-01

    In this paper we present numerical investigation of the influence of intrapulse Raman scattering (IRS) on the stable stationary pulses. Our basic equation, namely cubic-quintic Ginzburg-Landau equation describes the propagation of ultra-short optical pulses under the effect of IRS in the presence of linear and nonlinear gain as well as spectral filtering. Our aim is to examine numerically the influence of IRS, on the stable stationary pulses in the presence of constant linear and nonlinear gain as well as spectral filtering. Numerical solution of our basic equation is performed by means of the "fourth-order Runge-Kutta method in the interaction picture method" method. We found that the small change of the value of the parameter which describes IRS leads to qualitatively different behavior of the evolution of pulse amplitudes. In order to study the observed strong dependence on the IRS, the perturbation method of conserved quantities of the nonlinear Schrodinger equation is applied. The numerical analysis of the derived nonlinear system of ordinary differential equations has shown that our numerical findings are related to the existence of the Poincare-Andronov-Hopf bifurcation.

  20. Retrofitting an electrostatic precipitator into a hybrid electrostatic precipitator by installing a pulse-jet fabric filter : Review of available technologies for retrofitting Electrostatic precipitator with fabric filter

    OpenAIRE

    Eskelinen, Petri

    2015-01-01

    The tightening of regulations related to particle emissions has made retrofitting the ESP into a hybrid of the ESP and a baghouse filter a possible solution to some old plants in Finland. The objective of this thesis was to assess when this is a viable option and to study the advantage and limitations of the system by comparing it to other options available to companies when they need to have more efficient filters. For this purpose, is was necessary to compile the pricing of a new ESP and...

  1. Characterization of nonlinear saturation and mode-locking potential of ionically-doped colored glass filter for short-pulse fiber lasers.

    Science.gov (United States)

    Zhang, M; Kelleher, E J R; Popov, S V; Taylor, J R

    2013-05-20

    The nonlinear saturable absorption of an ionically-doped colored glass filter is measured directly using a Z-scan technique. For the first time, we demonstrate the potential of this material as a saturable asborber in fiber lasers. We achieve mode-locking of an ytterbium doped system. Mode-locking of cavities with all-positive and net-negative group velocity dispersion are demonstrated, achieving pulse durations of 60 ps and 4.1 ps, respectively. This inexpensive and optically robust material, with the potential for broadband operation, could surplant other saturable absorber devices in affordable mode-locked fiber lasers.

  2. Electric field induced needle-pulsed arc discharge carbon nanotube production apparatus: circuitry and mechanical design.

    Science.gov (United States)

    Kia, Kaveh Kazemi; Bonabi, Fahimeh

    2012-12-01

    A simple and low cost apparatus is reported to produce multiwall carbon nanotubes and carbon nano-onions by a low power short pulsed arc discharge reactor. The electric circuitry and the mechanical design details and a micro-filtering assembly are described. The pulsed-plasma is generated and applied between two graphite electrodes. The pulse width is 0.3 μs. A strong dc electric field is established along side the electrodes. The repetitive discharges occur in less than 1 mm distance between a sharp tip graphite rod as anode, and a tubular graphite as cathode. A hydrocarbon vapor, as carbon source, is introduced through the graphite nozzle in the cathode assembly. The pressure of the chamber is controlled by a vacuum pump. A magnetic field, perpendicular to the plasma path, is provided. The results show that the synergetic use of a pulsed-current and a dc power supply enables us to synthesize carbon nanoparticles with short pulsed plasma. The simplicity and inexpensiveness of this plan is noticeable. Pulsed nature of plasma provides some extra degrees of freedom that make the production more controllable. Effects of some design parameters such as electric field, pulse frequency, and cathode shape are discussed. The products are examined using scanning probe microscopy techniques.

  3. Electric field induced needle-pulsed arc discharge carbon nanotube production apparatus: Circuitry and mechanical design

    Science.gov (United States)

    Kia, Kaveh Kazemi; Bonabi, Fahimeh

    2012-12-01

    A simple and low cost apparatus is reported to produce multiwall carbon nanotubes and carbon nano-onions by a low power short pulsed arc discharge reactor. The electric circuitry and the mechanical design details and a micro-filtering assembly are described. The pulsed-plasma is generated and applied between two graphite electrodes. The pulse width is 0.3 μs. A strong dc electric field is established along side the electrodes. The repetitive discharges occur in less than 1 mm distance between a sharp tip graphite rod as anode, and a tubular graphite as cathode. A hydrocarbon vapor, as carbon source, is introduced through the graphite nozzle in the cathode assembly. The pressure of the chamber is controlled by a vacuum pump. A magnetic field, perpendicular to the plasma path, is provided. The results show that the synergetic use of a pulsed-current and a dc power supply enables us to synthesize carbon nanoparticles with short pulsed plasma. The simplicity and inexpensiveness of this plan is noticeable. Pulsed nature of plasma provides some extra degrees of freedom that make the production more controllable. Effects of some design parameters such as electric field, pulse frequency, and cathode shape are discussed. The products are examined using scanning probe microscopy techniques.

  4. Effect of C{sub 2}H{sub 2} flow rate on microstructure and properties of nc–Cu/a–C:H nanocomposite films prepared by filtered cathodic vaccum arc technique

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Haiqiang; Chen, Yiming; Liao, Bin; Wu, Xianying; Zhang, Huixing [Key Laboratory of Beam Technology and Material Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University, Beijing 100875 (China); Zhang, Xu, E-mail: zhangxu@bnu.edu.cn [Key Laboratory of Beam Technology and Material Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University, Beijing 100875 (China)

    2013-07-15

    Nc–Cu/a–C:H nanocomposite films are deposited by filtered cathodic vaccum arc (FCVA) technique using C{sub 2}H{sub 2} as the precursor. The effects of C{sub 2}H{sub 2} flow rate on the microstructure, composition and properties of nc–Cu/a–C:H films have been studied by Raman spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and nanoindentation test. In these films, copper nanoparticles (3.5–15 nm) are embedded in the amorphous carbon matrix, which could be confirmed by XRD analysis. Raman spectroscopy and XPS results confirm the decrease of sp{sup 3} content with the increasing copper fraction, which could be a result of more severe thermalization on carbon matrix owing to the presence of copper. The compressive stresses of these films, calculated by Stoney’s equation, are found to be as low as 0.5 Gpa, declining with the increasing copper content. Nanoindentation measurements reveal that the film hardness falls monotonically as the Cu content in the films increases.

  5. Assessment of Current Cathodic Protection System of a Circulating Water Debris Filter in the Power Plant%电厂循环水碎屑过滤器现行阴极保护系统的评估

    Institute of Scientific and Technical Information of China (English)

    王文奋; 孙永亮; 刘晓军

    2014-01-01

    通过对某电厂过滤器的运行环境、牺牲阳极种类、阳极的设计计算、阳极的安装、运行现状分析,确认其循环水系统碎屑过滤器现有阴极保护系统大体满足防腐蚀的要求。为更好地运行,建议其更换牺牲阳极种类并对不溶解的阳极进行成分分析及电化学性能测试,对采购的阳极进行抽样检测,对每只安装的新阳极测量电连接。%Operating environment, type, design, installation,operation status of sacrificial anode were applied to analysis the effect of current cathodic protection system of a circulating water debris filter in the power plant,result shows that the system generally meet the requirements of anti-corrosion. In order to better operation, improvement measures, such as replacing the sacrificial anode and analysising the components and testing electrochemical performance of the insoluble anode, Sampling for testing and measuring the anode electrical connection were proposed.

  6. RF Electron Gun with Driven Plasma Cathode

    CERN Document Server

    Khodak, Igor

    2005-01-01

    It's known that RF guns with plasma cathodes based on solid-state dielectrics are able to generate an intense electron beam. In this paper we describe results of experimental investigation of the single cavity S-band RF gun with driven plasma cathode. The experimental sample of the cathode based on ferroelectric ceramics has been designed. Special design of the cathode permits to separate spatially processes of plasma development and electron acceleration. It has been obtained at RF gun output electron beam with particle energy ~500 keV, pulse current of 4 A and pulse duration of 80 ns. Results of experimental study of beam parameters are referred in. The gun is purposed to be applied as the intense electron beam source for electron linacs.

  7. LOW TEMPERATURE CATHODE SUPPORTED ELECTROLYTES

    Energy Technology Data Exchange (ETDEWEB)

    Harlan U. Anderson; Fatih Dogan; Vladimir Petrovsky

    2002-03-31

    This project has three main goals: Thin Films Studies, Preparation of Graded Porous Substrates and Basic Electrical Characterization and testing of Planar Single Cells. This period has continued to address the problem of making dense 1/2 to 5 {micro}m thick dense layers on porous substrates (the cathode LSM). Our current status is that we are making structures of 2-5 cm{sup 2} in area, which consist of either dense YSZ or CGO infiltrated into a 2-5 {micro}m thick 50% porous layer made of either nanoncrystalline CGO or YSZ powder. This composite structure coats a macroporous cathode or anode; which serves as the structural element of the bi-layer structure. These structures are being tested as SOFC elements. A number of structures have been evaluated both as symmetrical and as button cell configuration. Results of this testing indicates that the cathodes contribute the most to cell losses for temperatures below 750 C. In this investigation different cathode materials were studied using impedance spectroscopy of symmetric cells and IV characteristics of anode supported fuel cells. Cathode materials studied included La{sub 0.8}Sr{sub 0.2}Co{sub 0.2}Fe{sub 0.8}O{sub 3} (LSCF), La{sub 0.7}Sr{sub 0.2}MnO{sub 3} (LSM), Pr{sub 0.8}Sr{sub 0.2}Fe{sub 0.8}O{sub 3} (PSCF), Sm{sub 0.8}Sr{sub 0.2}Co{sub 0.2}Fe{sub 0.8}O{sub 3} (SSCF), and Yb{sub .8}Sr{sub 0.2}Co{sub 0.2}Fe{sub 0.8}O{sub 3} (SSCF). A new technique for filtering the Fourier transform of impedance data was used to increase the sensitivity of impedance analysis. By creating a filter specifically for impedance spectroscopy the resolution was increased. The filter was tailored to look for specific circuit elements like R//C, Warburg, or constant phase elements. As many as four peaks can be resolved using the filtering technique on symmetric cells. It may be possible to relate the different peaks to material parameters, like the oxygen exchange coefficient. The cathode grouped in order from lowest to highest ASR is

  8. Deep oxidation of methane on particles derived from YSZ-supported Pd-Pt-(O) coatings synthesized by pulsed filtered cathodic arc

    Energy Technology Data Exchange (ETDEWEB)

    Horwat, D.; Endrino, J.L.; Boreave, A.; Karoum,R.; Pierson, J.F.; Weber, S.; Anders, A.; Vernoux, Ph.

    2008-12-12

    Methane conversion tests were performed on Pd, PdOy, Pd0.6Pt0.4Oy and Pd0.4Pt0.6Oy thin films deposited on yttria stabilized zirconia (YSZ) substrates. Pt containing films exhibited poor activity and high reducibility. As-deposited Pd and PdOy films showed good activity and transformed, during the cycling process, to particles dispersed on the YSZ substrates. The higher reaction rate of initially PdOy films was explained by a better dispersion of the catalyst. A drop of the reaction rate was observed when the temperature exceeded 735oC and 725oC for initially Pd and PdOy, respectively, which can be associated with the high-temperature reduction of PdO into Pd.

  9. Development of Electron Gun of Carbon Nanotube Cathode

    CERN Document Server

    Hozumi, Yasufumi; Ohsawa, Satoshi; Sugimura, Takashi

    2005-01-01

    We are developing high brightness electron guns utilizing carbon nanotube (CNT) cathodes. Recently, we succeeded to achieved field emission currents to 0.2 A (3 A/cm2) from a triode type CNT cathode of 3 mm diameter. The emission tests were performed at DC100kV acceleration voltage in pulse operations of 50 Hz using 6 nsec pulses. The emission currents were very stable for long term periods of 3 weeks. Photo emission tests from CNT cathode by 266nm laser pulses is also due to be reported simultaneously.

  10. Preliminary Results of Field Emission Cathode Tests

    Science.gov (United States)

    Sovey, James S.; Kovaleski, Scott D.

    2001-01-01

    Preliminary screening tests of field emission cathodes such as chemical vapor deposited (CVD) diamond, textured pyrolytic graphite, and textured copper were conducted at background pressures typical of electric thruster test facilities to assess cathode performance and stability. Very low power electric thrusters which provide tens to hundreds micronewtons of thrust may need field emission neutralizers that have a capability of tens to hundreds of microamperes. From current voltage characteristics, it was found that the CVD diamond and textured metals cathodes clearly satisfied the Fowler-Nordheim emission relation. The CVD diamond and a textured copper cathode had average current densities of 270 and 380 mA/sq cm, respectively, at the beginning-of-life. After a few hours of operation the cathode emission currents degraded by 40 to 75% at background pressures in the 10(exp -5) Pa to 10(exp -4) Pa range. The textured pyrolytic graphite had a modest current density at beginning-of-life of 84 mA/sq cm, but this cathode was the most stable of all. Extended testing of the most promising cathodes is warranted to determine if current degradation is a burn-in effect or whether it is a long-term degradation process. Preliminary experiments with ferroelectric emission cathodes, which are ceramics with spontaneous electric polarization, were conducted. Peak current densities of 30 to 120 mA/sq cm were obtained for pulse durations of about 500 ns in the 10(exp -4) Pa pressure range.

  11. Degradation kinetics of aflatoxin B1 and B2 in filter paper and rough rice by using pulsed light irradiation

    Science.gov (United States)

    Rough rice is susceptible to contamination by aflatoxins, which are highly toxic, mutagenic and carcinogenic compounds. To develop aflatoxin degradation technology for rice with the use of pulsed light (PL) treatment, the objective of this study was to investigate the degradation characters of aflat...

  12. Highly Efficient Storage of Pulse Energy Produced by Triboelectric Nanogenerator in Li3V2(PO4)3/C Cathode Li-Ion Batteries.

    Science.gov (United States)

    Nan, Xihui; Zhang, Changkun; Liu, Chaofeng; Liu, Mengmeng; Wang, Zhong Lin; Cao, Guozhong

    2016-01-13

    Triboelectric nanogenerator (TENG) has been considered as a new type of energy harvesting technology, which employs the coupling effects of triboelectrification and electrostatic induction. One key factor having limited its application is the energy storage. In this work, a high performance Li3V2(PO4)3/C material synthesized by low-cost hydrothermal method followed with subsequent annealing treatment was studied to efficiently store the power generated by a radial-arrayed rotary TENG. Not only does the Li3V2(PO4)3/C exhibit a discharge capacity of 128 mAh g(-1) at 1 C with excellent cyclic stability (capacity retention is 90% after 1000 cycles at a rate of 5 C) in Li-ion battery, but also shows outstanding energy conversion efficiency (83.4%) compared with the most popular cathodic materials: LiFePO4 (74.4%), LiCoO2 (66.1%), and LiMn2O4 (73.6%) when it was charged by high frequency and large current electricity directly from by TENG.

  13. Development of plasma cathode electron guns

    Science.gov (United States)

    Oks, Efim M.; Schanin, Peter M.

    1999-05-01

    The status of experimental research and ongoing development of plasma cathode electron guns in recent years is reviewed, including some novel upgrades and applications to various technological fields. The attractiveness of this kind of e-gun is due to its capability of creating high current, broad or focused beams, both in pulsed and steady-state modes of operation. An important characteristic of the plasma cathode electron gun is the absence of a thermionic cathode, a feature which leads to long lifetime and reliable operation even in the presence of aggressive background gas media and at fore-vacuum gas pressure ranges such as achieved by mechanical pumps. Depending on the required beam parameters, different kinds of plasma discharge systems can be used in plasma cathode electron guns, such as vacuum arcs, constricted gaseous arcs, hollow cathode glows, and two kinds of discharges in crossed E×B fields: Penning and magnetron. At the present time, plasma cathode electron guns provide beams with transverse dimension from fractional millimeter up to about one meter, beam current from microamperes to kiloamperes, beam current density up to about 100 A/cm2, pulse duration from nanoseconds to dc, and electron energy from several keV to hundreds of keV. Applications include electron beam melting and welding, surface treatment, plasma chemistry, radiation technologies, laser pumping, microwave generation, and more.

  14. Cathode heating mechanisms in pseudospark plasma switches

    Science.gov (United States)

    Sommerer, Timothy J.; Pak, Hoyoung; Kushner, Mark J.

    1992-10-01

    Pseudosparks, and the back-lighted thyratron (BLT) in particular, are finding increasing application as pulse power switches. An attractive feature of BLTs is that high current densities (≥ tens of kA cm-2) can be sustained from metal cathodes without auxiliary heating. The source of this current is believed to be electric-field-enhanced thermionic emission resulting from heating of the cathode by ion bombardment during commutation which ultimately melts the surface of the cathode. It is proposed that a photon-driven ionization mechanism in the interelectrode gap of the BLT is responsible for initiating the observed patterns of cathode surface melting and electron emission. A 21/2-dimensional computer model is presented that incorporates a photo-induced ionization mechanism to spread the plasma into the interelectrode gap. It predicts a melting of the cathode in a pattern similar to that which is experimentally observed, and predicts a rate of field-enhanced thermionic electron emission that is sufficient to explain the high BLT conduction current density. In the absence of these mechanisms, the model does not predict the observed large-area melting of the face of the cathode. The cathode heating rate during the BLT switching phase is maximum for operating parameters that are very close to the limit for which the switch will close (that is, the smallest possible pressure-electrode spacing product and smallest possible electrode holes).

  15. Microhollow cathode discharges

    Science.gov (United States)

    Schoenbach, K. H.; Moselhy, M.; Shi, W.; Bentley, R.

    2003-07-01

    By reducing the dimensions of hollow cathodes into the hundred micrometer range, stable, direct current, high (atmospheric) pressure glow discharges in rare gases, rare gas-halide mixtures and in air could be generated. The electron energy distribution in these microdischarges is non-Maxwellian, with a pronounced high-energy tail. The high electron energy together with the high gas density, which favors three-body collisions, is the reason for an efficient excimer generation in these microplasmas. Excimer efficiencies from 1% to 9% have been measured for argon, xenon, argon fluoride, and xenon chloride direct current excimer emitters, with a radiant excimer emittance of up to 2 W/cm2 for xenon. Adding small amounts of oxygen to argon has allowed us to generate vacuum ultraviolet line radiation at 130.5 nm with an efficiency approaching 1%. Pulsing xenon discharges with nanosecond electrical pulses has led to an increase in intensity to 15 W/cm2 and to a simultaneous increase in efficiency to more than 20%. Operating the discharges in an abnormal glow mode has allowed us to generate microdischarge arrays without individual ballast. Applications of these plasma arrays are excimer lamps and plasma reactors.

  16. Semiclassical modelling of finite-pulse effects on non-adiabatic photodynamics via initial condition filtering: The predissociation of NaI as a test case

    Energy Technology Data Exchange (ETDEWEB)

    Martínez-Mesa, Aliezer [Departmento de Física Teórica, Universidad de la Habana, San Lázaro y L, La Habana 10400 (Cuba); Institut für Chemie, Universität Potsdam, Karl-Liebknecht-Strasse 24-25, D-14476 Potsdam-Golm (Germany); Saalfrank, Peter [Institut für Chemie, Universität Potsdam, Karl-Liebknecht-Strasse 24-25, D-14476 Potsdam-Golm (Germany)

    2015-05-21

    Femtosecond-laser pulse driven non-adiabatic spectroscopy and dynamics in molecular and condensed phase systems continue to be a challenge for theoretical modelling. One of the main obstacles is the “curse of dimensionality” encountered in non-adiabatic, exact wavepacket propagation. A possible route towards treating complex molecular systems is via semiclassical surface-hopping schemes, in particular if they account not only for non-adiabatic post-excitation dynamics but also for the initial optical excitation. One such approach, based on initial condition filtering, will be put forward in what follows. As a simple test case which can be compared with exact wavepacket dynamics, we investigate the influence of the different parameters determining the shape of a laser pulse (e.g., its finite width and a possible chirp) on the predissociation dynamics of a NaI molecule, upon photoexcitation of the A(0{sup +}) state. The finite-pulse effects are mapped into the initial conditions for semiclassical surface-hopping simulations. The simulated surface-hopping diabatic populations are in qualitative agreement with the quantum mechanical results, especially concerning the subpicosend photoinduced dynamics, the main deviations being the relative delay of the non-adiabatic transitions in the semiclassical picture. Likewise, these differences in the time-dependent electronic populations calculated via the semiclassical and the quantum methods are found to have a mild influence on the overall probability density distribution. As a result, the branching ratios between the bound and the dissociative reaction channels and the time-evolution of the molecular wavepacket predicted by the semiclassical method agree with those computed using quantum wavepacket propagation. Implications for more challenging molecular systems are given.

  17. Characterization of multicapillary dielectric cathodes

    Science.gov (United States)

    Gleizer, J. Z.; Hadas, Y.; Yarmolich, D.; Felsteiner, J.; Krasik, Ya. E.

    2007-04-01

    Parameters of the plasma and electron beam produced by a multicapillary cathode in a diode powered by a ˜200kV, ˜300ns pulse are presented. It was found that the source of electrons is the plasma ejected from the capillaries. Inside the capillaries this plasma obtains electron density and temperature of ˜8×1015cm-3 and ˜5eV, respectively. In the vicinity of the cathode, the density and temperature of the plasma electrons were found to be 2×1014cm-3 and 4.5eV, respectively, for electron current density of ˜40A/cm2. It was shown that the plasma expansion velocity is in the range of (1-2)×106cm/s for current density of >12A/cm2.

  18. Numerical Analysis of Flow Field in Ceramic Filter During Pulse Cleaning%陶瓷过滤器脉冲反吹系统的流场的数值模拟

    Institute of Scientific and Technical Information of China (English)

    姬忠礼; 彭书; 谭立村

    2003-01-01

    In the commercial utilization of rigid ceramic filters, the performance of pulse cleaning has crucial effects on the long-term stable operation. In order to get a clear insight into the nature of this cleaning process and provide a solid basis for industrial applications, the flow in ceramic candle filter was investigated. The flow in the pulse-jet space and inside the ceramic candle is regarded as two- dimensional, unsteady, compressible flow, and numerical simulation is carried out by computational fluid dynamics. The numerical predictions of flow field are in good agreement with the experimental measurements. Effects of the candle diameter, the separation distance between the nozzle and the candle injector and the length of the candle on the flowfield have been numerically analyzed to provide the basis for the optimum design of the pulse cleaning system.

  19. High-Current Cold Cathode Employing Diamond and Related Materials

    Energy Technology Data Exchange (ETDEWEB)

    Hirshfield, Jay L. [Omega-P, Inc., New Haven, CT (United States)

    2014-10-22

    The essence of this project was for diamond films to be deposited on cold cathodes to improve their emission properties. Films with varying morphology, composition, and size of the crystals were deposited and the emission properties of the cathodes that utilize such films were studied. The prototype cathodes fabricated by the methods developed during Phase I were tested and evaluated in an actual high-power RF device during Phase II. These high-power tests used the novel active RF pulse compression system and the X-band magnicon test facility at US Naval Research Laboratory. In earlier tests, plasma switches were employed, while tests under this project utilized electron-beam switching. The intense electron beams required in the switches were supplied from cold cathodes embodying diamond films with varying morphology, including uncoated molybdenum cathodes in the preliminary tests. Tests with uncoated molybdenum cathodes produced compressed X-band RF pulses with a peak power of 91 MW, and a maximum power gain of 16.5:1. Tests were also carried out with switches employing diamond coated cathodes. The pulse compressor was based on use of switches employing electron beam triggering to effect mode conversion. In experimental tests, the compressor produced 165 MW in a ~ 20 ns pulse at ~18× power gain and ~ 140 MW at ~ 16× power gain in a 16 ns pulse with a ~ 7 ns flat-top. In these tests, molybdenum blade cathodes with thin diamond coatings demonstrated good reproducible emission uniformity with a 100 kV, 100 ns high voltage pulse. The new compressor does not have the limitations of earlier types of active pulse compressors and can operate at significantly higher electric fields without breakdown.

  20. Microhollow Cathode Discharge Excimer Lamps

    Science.gov (United States)

    Schoenbach, K. H.

    1999-11-01

    character. Reducing the diameter of the cathode hole in a hollow cathode discharge geometry to values on the order of 100 μm has allowed us to extend the pressure range of stable, direct current hollow cathode gas discharges up to atmospheric pressure. The large concentration of high-energy electrons generated in the cathode fall, in combination with the high neutral gas density favors three-body processes such as excimer formation. Excimer emission in xenon discharges peaking at 172 nm, was observed with efficiencies between 6% and 9% at pressures of several hundred Torr. Typical forward voltages are 200 V at dc currents up to 8 mA. Pulsed operation allowed us to extend the current range to 80 mA with corresponding linear increase in optical power. Spatially resolved measurements showed that the source of the excimer radiation at atmospheric pressure and currents of less than 8 mA is confined to the cathode opening. The radiative emittance at 8 mA and atmospheric pressure is approximately 20 W/cm^2. With reduced pressure and increased current, respectively, the excimer source extends into the area outside the cathode hole. Besides in xenon, excimer emission in argon at a peak wavelength of 128 nm has been recorded. In addition to operating the discharge in rare gases, we have also explored its use as rare gas-halide excimer source. In a gas mixture containing 1% ArF we were able to generate stable dc discharges in flowing gas at pressures ranging from 100 Torr to atmospheric pressure. The spectra of the high-pressure ArF discharges are dominated by excimer radiation peaking at 193 nm. The excimer emission of a single ArF discharge at 700 Torr was measured as 150 mW at an efficiency of 3%. Parallel operation of these discharges by means of a resistive anode, which has recently been demonstrated for argon discharges, offers the possibility to use microhollow cathode discharge arrays as dc-excimer lamps, with estimated power densities exceeding 10 W/cm^2. abstract

  1. Flash 型 FPGA 单粒子瞬态脉冲分段滤除电路设计%Segmented Filtering Circuit for SET Pulse in Flash-based FPGAs

    Institute of Scientific and Technical Information of China (English)

    史方显; 曾立; 王淼; 曹建勋; 权妙静

    2016-01-01

    为提高 FPGA 在辐射环境条件下的抗单粒子脉冲(SET)的能力,设计了一种由多个延时单元和并联逻辑保护单元(Guard Gate,GG)构成的 SET 脉冲分段滤除电路.将 SET 脉冲处理延时减小至传统方法的10.42%~49.8%,从而提高电路对 SET 脉冲的处理能力,同时占用的逻辑资源未有明显增加.%A segmented filtering circuit with delay units and guard gates is proposed to filter SET pulses with different width,considering the range and distribution of SET pulse widths produced in FPGA and the propagation induced pulse broadening.Dividing the widths of SET pulses into several intervals,parallel guard gates with different delay buffers generate corresponding results to different intervals.According to the results,this circuit selects the output in the shortest time,improving the performance on dealing with SET pulses.Simulation results in Fusion family flash-based FPGA indicate that,compared to traditional methods,the segmented filtering circuit can cut the filtering delay of SET pulse in critical path down to 10.42%~49.8%,while power consumption decreasing and no hardware resource increase.

  2. Preliminary experimental study of a carbon fiber array cathode

    Science.gov (United States)

    Li, An-kun; Fan, Yu-wei

    2016-08-01

    The preliminary experimental results of a carbon fiber array cathode for the magnetically insulated transmission line oscillator (MILO) operations are reported. When the diode voltage and diode current were 480 kV and 44 kA, respectively, high-power microwaves with a peak power of about 3 GW and a pulse duration of about 60 ns were obtained in a MILO device with the carbon fiber array cathode. The preliminary experimental results show that the shot-to-shot reproducibility of the diode current and the microwave power is stable until 700 shots. No obvious damage or deterioration can be observed in the carbon fiber surface morphology after 700 shots. Moreover, the cathode performance has no observable deterioration after 700 shots. In conclusion, the maintain-free lifetime of the carbon fiber array cathode is more than 700 shots. In this way, this carbon fiber array cathode offers a potential replacement for the existing velvet cathode.

  3. Composite Organic Radical - Inorganic Hybrid Cathode for Lithium-ion Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Qian; Cosimbescu, Lelia; Koech, Phillip K.; Choi, Daiwon; Lemmon, John P.

    2013-07-01

    A new organic radical inorganic hybrid cathode comprised of PTMA/LiFePO4 composite system is developed and reported for the first time. The hybrid cathodes demonstrate high pulse power capability resulting in a significant improvement over the pure PTMA or LiFePO4 cathode which is very promising for transportation and other high pulse power applications that require long cycle life and lower cost.

  4. Pulse plating

    CERN Document Server

    Hansal, Wolfgang E G; Green, Todd; Leisner, Peter; Reichenbach, Andreas

    2012-01-01

    The electrodeposition of metals using pulsed current has achieved practical importance in recent years. Although it has long been known that changes in potential, with or without polarity reversal, can significantly affect the deposition process, the practical application of this has been slow to be adopted. This can largely be explained in terms of the complex relationship between the current regime and its effect on the electrodeposition process. In order to harness these effects, an understanding of the anodic and cathodic electrochemical processes is necessary, together with the effects of polarity reversal and the rate of such reversals. In this new monograph, the basics of metal electrodeposition from solution are laid out in great detail in seven distinct chapters. With this knowledge, the reader is able to predict how a given pulse train profile can be adopted to achieve a desired outcome. Equally important is the choice of a suitable rectifier and the ancillary control circuits to enable pulse platin...

  5. Experimental study of cake formation on heat treated and membrane coated needle felts in a pilot scale pulse jet bag filter using optical in-situ cake height measurement.

    Science.gov (United States)

    Saleem, Mahmood; Khan, Rafi Ullah; Tahir, M Suleman; Krammer, Gernot

    2011-12-25

    Pulse-jet bag filters are frequently employed for particle removal from off gases. Separated solids form a layer on the permeable filter media called filter cake. The cake is responsible for increasing pressure drop. Therefore, the cake has to be detached at a predefined upper pressure drop limit or at predefined time intervals. Thus the process is intrinsically semi-continuous. The cake formation and cake detachment are interdependent and may influence the performance of the filter. Therefore, understanding formation and detachment of filter cake is important. In this regard, the filter media is the key component in the system. Needle felts are the most commonly used media in bag filters. Cake formation studies with heat treated and membrane coated needle felts in pilot scale pulse jet bag filter were carried out. The data is processed according to the procedures that were published already [Powder Technology, Volume 173, Issue 2, 19 April 2007, Pages 93-106]. Pressure drop evolution, cake height distribution evolution, cake patches area distribution and their characterization using fractal analysis on different needle felts are presented here. It is observed that concavity of pressure drop curve for membrane coated needle felt is principally caused by presence of inhomogeneous cake area load whereas it is inherent for heat treated media. Presence of residual cake enhances the concavity of pressure drop at the start of filtration cycle. Patchy cleaning is observed only when jet pulse pressure is too low and unable to provide the necessary force to detach the cake. The border line is very sharp. Based on experiments with limestone dust and three types of needle felts, for the jet pulse pressure above 4 bar and filtration velocity below 50 mm/s, cake is detached completely except a thin residual layer (100-200 μm). Uniformity and smoothness of residual cake depends on the surface characteristics of the filter media. Cake height distribution of residual cake and

  6. Planar-Focusing Cathodes

    CERN Document Server

    Lewellen, J W

    2005-01-01

    Conventional pi-mode rf photoinjectors typically use magnetic solenoids for emittance compensation. This provides independent focusing strength, but can complicate rf power feed placement, introduce asymmetries (due to coil crossovers), and greatly increase the cost of the photoinjector. Cathode-region focusing can also provide for a form of emittance compensation. Typically this method strongly couples focusing strength to the field gradient on the cathode, however, and also requires altering the longitudinal position of the cathode to change the focusing. We propose a new method for achieving cathode-region variable-strength focusing for emittance compensation. The new method reduces the coupling to the gradient on the cathode, and does not require a change in the longitudinal position of the cathode. Expected performance for an S-band system is similar to conventional solenoid-based designs. This paper presents the results of rf cavity and beam dynamics simulations of the new design.

  7. Cathodic Protection Model Facility

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Performs Navy design and engineering of ship and submarine impressed current cathodic protection (ICCP) systems for underwater hull corrosion control and...

  8. Glucose-Driven Fuel Cell Constructed from Enzymes and Filter Paper

    Science.gov (United States)

    Ge, Jun; Schirhagl, Romana; Zare, Richard N.

    2011-01-01

    A glucose-driven enzymatic filter-paper fuel cell is described. A strip of filter paper coated with carbon nanotubes and the glucose oxidase enzyme functions as the anode of the enzyme fuel cell. Another strip of filter paper coated with carbon nanotubes and the laccase enzyme functions as the cathode. Between the anode and the cathode, a third…

  9. Glucose-Driven Fuel Cell Constructed from Enzymes and Filter Paper

    Science.gov (United States)

    Ge, Jun; Schirhagl, Romana; Zare, Richard N.

    2011-01-01

    A glucose-driven enzymatic filter-paper fuel cell is described. A strip of filter paper coated with carbon nanotubes and the glucose oxidase enzyme functions as the anode of the enzyme fuel cell. Another strip of filter paper coated with carbon nanotubes and the laccase enzyme functions as the cathode. Between the anode and the cathode, a third…

  10. Startup and initial operation of a DFGD and pulse jet fabric filter system on Cokenergy's Indiana Harbor coke oven off gas system

    Energy Technology Data Exchange (ETDEWEB)

    Morris, W.J.; Gansley, R.R.; Schaddell, J.G.

    1999-07-01

    This paper describes the design, initial operation and performance testing of a Dry Flue Gas Desulfurization (DFGD) and Modular Pulse Jet Fabric Filter (MPJFF) system installed at Cokenergy's site in East Chicago, Indiana. The combined flue gas from the sixteen (16) waste heat recovery boilers is processed by the system to control emissions of sulfur dioxide and particulates. These boilers recover energy from coke oven off gas from Indiana Harbor Coke Company's coke batteries. The DFGD system consists of two 100% capacity absorbers. Each absorber vessel uses a single direct drive rotary atomizer to disperse the lime slurry for SO{sub 2} control. The MPJFF consists of thirty two (32) modules arranged in twin sixteen-compartment (16) units. The initial start up of the DFGD/MPJFF posed special operational issues due to the low initial gas flows through the system as the four coke oven batteries were cured and put in service for the first time. This occurred at approximately monthly intervals beginning in March 1998. A plan was implemented to perform a staged startup of the DFGD and MPJFF to coincide with the staged start up of the coke batteries and waste heat boilers. Operational issues that are currently being addressed include reliability of byproduct removal. Performance testing was conducted in August and September 1998 at the inlet of the system and the outlet stack. During these tests, particulate, SO{sub 2}, SO{sub 3}, and HCI emissions were measured simultaneously at the common DFGD inlet duct and the outlet stack. Measurements were also taken for average lime, water, and power consumption during the tests as well as system pressure losses. These results showed that all guarantee parameters were achieved during the test periods. The initial operation and performance testing are described in this paper.

  11. The cathode test stand for the DARHT second-axis

    Energy Technology Data Exchange (ETDEWEB)

    Fortgang, C.; Monroe, M.; Prono, D. [Los Alamos National Lab., NM (United States); Hudson, C.; Macy, D.; Moy, K. [Bechtel Nevada, Santa Barbara, CA (United States)

    1998-12-31

    The injector for the DARHT second-axis injector will use an 8-in. thermionic dispenser cathode. Because the cathode is relatively large and requires a large amount of heat (5 kW) there are certain engineering issues that need to be addressed, before the DARHT injector reaches the final design stage. The Cathode Test Stand (CTS) will be used to address those concerns. The CTS is a new facility, presently under construction. The CTS will consist of a high-voltage pulse modulator, a high-vacuum diode test-chamber, and a short beam-transport section with diagnostics. This paper discusses the status of the project.

  12. Plasma characterization on carbon fiber cathode by spectroscopic diagnostics

    Institute of Scientific and Technical Information of China (English)

    Liu Lie; Li Li-Min; Xu Qi-Fu; Chang Lei; Wen Jian-Chun

    2009-01-01

    This paper mainly investigates plasma characterization on carbon fiber cathodes with and without cesium iodide (CsI) coating powered by a~300 ns,~200 kV accelerating pulse. It was found that the CsI layers can not only improve the diode voltage,but also maintain a stable perveance.This indicates a slowly changed diode gap or a low cathode plasma expansion velocity.By spectroscopic diagnostics,in the vicinity of the cathode surface the average plasma density and temperature were found to be~3×1014 cm-3 and~5 eV,respectively,for an electron current density of~40 A/cm2.Furthermore,there exists a multicomponent plasma expansion toward the anode.The plasma expansion velocity,corresponding to the carbon and hydrogen ions,is estimated to be~1.5 cm/μs.Most notably,Cs spectroscopic line was obtained only at the distance ≤0.5 mm from the cathode surface.Carbon and hydrogen ions are obtained up to the distance of 2.5 mm from the cathode surface.Cs ions almost remain at the vicinity of the cathode surface.These results show that the addition of Cal enables a slow cathode plasma expansion toward the anode,providing a positive prospect for developing long-pulse electron beam sources.

  13. 机载LiDAR数据的多回波信息分析及应用研究%Analysis of multiple returns of airborne LiDAR pulse and its application in filtering

    Institute of Scientific and Technical Information of China (English)

    林祥国; 张继贤

    2013-01-01

    本文通过分析机载LiDAR系统获取的激光数据的多回波特性,阐述了多回波信息对地物类型信息的揭示作用,并将多回波特性用于减少参与滤波的激光脚点数量.实验证明,本文提出的滤波方案,可以预先剔除掉大部分的植被激光脚点和部分的建筑物激光脚点,既减少了参与滤波的数据量,又可以改善滤波算法对建筑物和植被的滤除效果.%A Laser pulse emitted by an airborne LiDAR system can receive multiple echoes, and the return number of a footprint is useful to determine the type of the object that reflects the above pulse. The above characteristic could be employed to reduce the number of points that are input for filtering. Particularly, the first echoes and the intermediate echoes were removed from the raw data, and they were also used to detect the non-ground points from the last echoes and the singular echoes, then only the reserved last pulses and the singular echoes were input for filtering in the paper. Experiments showed that the method could enhance the accuracy of filtering despite that the number of points input for filtering was reduced.

  14. An improved reservoir oxide cathode

    Science.gov (United States)

    Wang, Xiaoxia; Liao, Xianheng; Luo, Jirun; Zhao, Qinglan

    2005-09-01

    A new type of reservoir oxide cathode has been developed in IECAS. The emission characteristics of the cathode are tested. The results show the new cathode has higher emission current density and better resistance to poisoning at same operating condition compared with those of conventional reservoir oxide cathode.

  15. THE INDUSTRIAL TEST OF PULSE BAG FILTER IN PETROLEUM COKE SUPERFINE GRINDING PROCESS%石油焦超细粉碎工艺中的脉冲袋式除尘器试验

    Institute of Scientific and Technical Information of China (English)

    周奇杰; 陈海焱; 张明星; 郑娟; 王焱

    2011-01-01

    Using superfine crushing grading equipment,the dust resistance after injecting,filtration speed and the dust resistance fluctuation when blowing in grinding process were tested.The test conditions were respectively different filtration area,different filtration speed,different filter inlet dust concentration and different pulse width.The results showed that for petroleum coke is light and has adhesion,the filtration speed should not exceed 2.17 m/min.And considering the dust removal efficiency and economic benefit,the filtration speed should better be controlled in 1.3 m/min.Both the filter inlet dust concentration and the pulse width had certain influence on the dust resistance after injecting and the dust resistance fluctuation when blowing.The dust resistance and the dust resistance fluctuation were small,when the filter inlet dust concentration was low.And pulse jet filter exists a best pulse width,0.08 s is the best one for this experimental filter.%利用超细粉碎分级设备,分别测试粉碎工艺中除尘器在不同过滤面积、过滤风速、入口粉尘浓度时,喷吹后的除尘器阻力、过滤风速、喷吹时的除尘器阻力波动情况;测试脉冲宽度对喷吹后除尘器阻力和喷吹时除尘器阻力波动的影响。结果表明:由于石油焦的轻质和黏附性特性,过滤风速不应超过2.17 m/min,考虑到除尘效率和经济效益,最好控制在1.3 m/min以内;除尘器入口粉尘浓度的高低对喷吹后除尘器阻力和喷吹时除尘器阻力波动均存在较大影响,入口粉尘浓度低时,阻力和阻力波动都较小;脉冲宽度对喷吹后除尘器阻力和喷吹时除尘器阻力波

  16. A hollow cathode ion source for production of primary ions for the BNL electron beam ion source.

    Science.gov (United States)

    Alessi, James; Beebe, Edward; Carlson, Charles; McCafferty, Daniel; Pikin, Alexander; Ritter, John

    2014-02-01

    A hollow cathode ion source, based on one developed at Saclay, has been modified significantly and used for several years to produce all primary 1+ ions injected into the Relativistic Heavy Ion Collider Electron Beam Ion Source (EBIS) at Brookhaven. Currents of tens to hundreds of microamperes have been produced for 1+ ions of He, C, O, Ne, Si, Ar, Ti, Fe, Cu, Kr, Xe, Ta, Au, and U. The source is very simple, relying on a glow discharge using a noble gas, between anode and a solid cathode containing the desired species. Ions of both the working gas and ionized sputtered cathode material are extracted, and then the desired species is selected using an ExB filter before being transported into the EBIS trap for charge breeding. The source operates pulsed with long life and excellent stability for most species. Reliable ignition of the discharge at low gas pressure is facilitated by the use of capacitive coupling from a simple toy plasma globe. The source design, and operating experience for the various species, is presented.

  17. A hollow cathode ion source for production of primary ions for the BNL electron beam ion source

    Energy Technology Data Exchange (ETDEWEB)

    Alessi, James, E-mail: alessi@bnl.gov; Beebe, Edward; Carlson, Charles; McCafferty, Daniel; Pikin, Alexander; Ritter, John [Collider-Accelerator Department, Brookhaven National Laboratory, Upton, New York 11973 (United States)

    2014-02-15

    A hollow cathode ion source, based on one developed at Saclay, has been modified significantly and used for several years to produce all primary 1+ ions injected into the Relativistic Heavy Ion Collider Electron Beam Ion Source (EBIS) at Brookhaven. Currents of tens to hundreds of microamperes have been produced for 1+ ions of He, C, O, Ne, Si, Ar, Ti, Fe, Cu, Kr, Xe, Ta, Au, and U. The source is very simple, relying on a glow discharge using a noble gas, between anode and a solid cathode containing the desired species. Ions of both the working gas and ionized sputtered cathode material are extracted, and then the desired species is selected using an ExB filter before being transported into the EBIS trap for charge breeding. The source operates pulsed with long life and excellent stability for most species. Reliable ignition of the discharge at low gas pressure is facilitated by the use of capacitive coupling from a simple toy plasma globe. The source design, and operating experience for the various species, is presented.

  18. Nanostructured sulfur cathodes

    KAUST Repository

    Yang, Yuan

    2013-01-01

    Rechargeable Li/S batteries have attracted significant attention lately due to their high specific energy and low cost. They are promising candidates for applications, including portable electronics, electric vehicles and grid-level energy storage. However, poor cycle life and low power capability are major technical obstacles. Various nanostructured sulfur cathodes have been developed to address these issues, as they provide greater resistance to pulverization, faster reaction kinetics and better trapping of soluble polysulfides. In this review, recent developments on nanostructured sulfur cathodes and mechanisms behind their operation are presented and discussed. Moreover, progress on novel characterization of sulfur cathodes is also summarized, as it has deepened the understanding of sulfur cathodes and will guide further rational design of sulfur electrodes. © 2013 The Royal Society of Chemistry.

  19. Cathodic hydrodimerization of nitroolefins

    OpenAIRE

    Michael Weßling; Hans J. Schäfer

    2015-01-01

    Nitroalkenes are easily accessible in high variety by condensation of aldehydes with aliphatic nitroalkanes. They belong to the group of activated alkenes that can be hydrodimerized by cathodic reduction. There are many olefins with different electron withdrawing groups used for cathodic hydrodimerization, but not much is known about the behaviour of the nitro group. Synthetic applications of this group could profit from the easy access to nitroolefins in large variety, the C–C bond formation...

  20. The subband pulse compression method based on quadratture mirror filter (QMF) banks%基于正交镜像滤波器组的子带脉冲压缩方法

    Institute of Scientific and Technical Information of China (English)

    高翠翠; 林明; 钱春雷

    2015-01-01

    针对超宽带雷达频带分割滤波器不理想、导致子带脉冲压缩和直接脉冲压缩结果相差较大的问题,本文提出了基于正交镜像滤波器组的子带脉冲压缩方法。首先设计了近似完全重建的正交镜像滤波器组,定义目标函数为通带误差、阻带能量和失真转移函数平方误差的加权和,通过无约束的变尺度方法将其最小化,然后用设计的正交镜像滤波器作为频带分割滤波器,实现子带脉冲压缩。仿真结果表明,本文设计的正交镜像滤波器组,相比现有的设计,具有更小的峰值重建误差、通带和阻带误差。提出的子带脉冲压缩方法,与传统方法相比,主副瓣比和主瓣宽度等脉压性能也明显提高。%For the problem that ultra-wideband (UWB)radar channel dropping filter isn′t ideal, which causes big error between subband pulse compression and direct pulse compression, a new method of subband pulse compression of UWB radar is presented. In the new method, nearly perfect-reconstruction two-channel quadrature mirror filter banks is designed at first. The objective function is formulated as a weighted sum of pass-band error and stop-band residual energy of low-pass prototype filter , and the square error of the distortion transfer function, which is minimized by unconstrained indirect update optimization method. The QMF replaces channel dropping filter. Compared with traditional subband pulse pressure method, simulation results show that the mainlobe to sidelobe and mainlobe width in proposed method are improved obviously.

  1. High-pressure hollow cathode discharges

    Science.gov (United States)

    Schoenbach, Karl H.; El-Habachi, Ahmed; Shi, Wenhui; Ciocca, Marco

    1997-11-01

    Reducing the diameter of the cathode hole in a plane anode - hollow cathode geometry to 0963-0252/6/4/003/img1m has allowed us to generate direct current discharges in argon at atmospheric pressure. Up to pressure times cathode hole diameter (pD) values of approximately 5 Torr cm, and at sub-mA currents, glow discharges (predischarges) are observed with a shape which is determined by the vacuum electric field. In the same pD range, but at higher currents of up to approximately 4 mA, the discharges are of the hollow cathode discharge type. At pD values exceeding 5 Torr cm the predischarges turn into surface discharges along the mica spacer between the electrodes. At currents > 4 mA filamentary, pulsed discharges are observed. Qualitative information on the electron energy distribution in the microdischarges has been obtained by studying the VUV emission from ionized argon atoms and the argon excimer radiation at 130 nm. The results of the spectral measurements indicate the presence of a relatively large concentration of electrons with energies > 15 eV over the entire pressure range. The fact that the current - voltage characteristic of the microdischarges has a positive slope over much of the current range where excimer radiation is emitted indicates the possibility of forming arrays of these discharges and using them in flat panel excimer lamps.

  2. Hybrid Filter Membrane

    Science.gov (United States)

    Laicer, Castro; Rasimick, Brian; Green, Zachary

    2012-01-01

    Cabin environmental control is an important issue for a successful Moon mission. Due to the unique environment of the Moon, lunar dust control is one of the main problems that significantly diminishes the air quality inside spacecraft cabins. Therefore, this innovation was motivated by NASA s need to minimize the negative health impact that air-suspended lunar dust particles have on astronauts in spacecraft cabins. It is based on fabrication of a hybrid filter comprising nanofiber nonwoven layers coated on porous polymer membranes with uniform cylindrical pores. This design results in a high-efficiency gas particulate filter with low pressure drop and the ability to be easily regenerated to restore filtration performance. A hybrid filter was developed consisting of a porous membrane with uniform, micron-sized, cylindrical pore channels coated with a thin nanofiber layer. Compared to conventional filter media such as a high-efficiency particulate air (HEPA) filter, this filter is designed to provide high particle efficiency, low pressure drop, and the ability to be regenerated. These membranes have well-defined micron-sized pores and can be used independently as air filters with discreet particle size cut-off, or coated with nanofiber layers for filtration of ultrafine nanoscale particles. The filter consists of a thin design intended to facilitate filter regeneration by localized air pulsing. The two main features of this invention are the concept of combining a micro-engineered straight-pore membrane with nanofibers. The micro-engineered straight pore membrane can be prepared with extremely high precision. Because the resulting membrane pores are straight and not tortuous like those found in conventional filters, the pressure drop across the filter is significantly reduced. The nanofiber layer is applied as a very thin coating to enhance filtration efficiency for fine nanoscale particles. Additionally, the thin nanofiber coating is designed to promote capture of

  3. Cathode materials review

    Energy Technology Data Exchange (ETDEWEB)

    Daniel, Claus, E-mail: danielc@ornl.gov; Mohanty, Debasish, E-mail: danielc@ornl.gov; Li, Jianlin, E-mail: danielc@ornl.gov; Wood, David L., E-mail: danielc@ornl.gov [Oak Ridge National Laboratory, 1 Bethel Valley Road, MS6472 Oak Ridge, TN 37831-6472 (United States)

    2014-06-16

    The electrochemical potential of cathode materials defines the positive side of the terminal voltage of a battery. Traditionally, cathode materials are the energy-limiting or voltage-limiting electrode. One of the first electrochemical batteries, the voltaic pile invented by Alessandro Volta in 1800 (Phil. Trans. Roy. Soc. 90, 403-431) had a copper-zinc galvanic element with a terminal voltage of 0.76 V. Since then, the research community has increased capacity and voltage for primary (nonrechargeable) batteries and round-trip efficiency for secondary (rechargeable) batteries. Successful secondary batteries have been the lead-acid with a lead oxide cathode and a terminal voltage of 2.1 V and later the NiCd with a nickel(III) oxide-hydroxide cathode and a 1.2 V terminal voltage. The relatively low voltage of those aqueous systems and the low round-trip efficiency due to activation energies in the conversion reactions limited their use. In 1976, Wittingham (J. Electrochem. Soc., 123, 315) and Besenhard (J. Power Sources 1(3), 267) finally enabled highly reversible redox reactions by intercalation of lithium ions instead of by chemical conversion. In 1980, Goodenough and Mizushima (Mater. Res. Bull. 15, 783-789) demonstrated a high-energy and high-power LiCoO{sub 2} cathode, allowing for an increase of terminal voltage far beyond 3 V. Over the past four decades, the international research community has further developed cathode materials of many varieties. Current state-of-the-art cathodes demonstrate voltages beyond any known electrolyte stability window, bringing electrolyte research once again to the forefront of battery research.

  4. Cathode materials review

    Science.gov (United States)

    Daniel, Claus; Mohanty, Debasish; Li, Jianlin; Wood, David L.

    2014-06-01

    The electrochemical potential of cathode materials defines the positive side of the terminal voltage of a battery. Traditionally, cathode materials are the energy-limiting or voltage-limiting electrode. One of the first electrochemical batteries, the voltaic pile invented by Alessandro Volta in 1800 (Phil. Trans. Roy. Soc. 90, 403-431) had a copper-zinc galvanic element with a terminal voltage of 0.76 V. Since then, the research community has increased capacity and voltage for primary (nonrechargeable) batteries and round-trip efficiency for secondary (rechargeable) batteries. Successful secondary batteries have been the lead-acid with a lead oxide cathode and a terminal voltage of 2.1 V and later the NiCd with a nickel(III) oxide-hydroxide cathode and a 1.2 V terminal voltage. The relatively low voltage of those aqueous systems and the low round-trip efficiency due to activation energies in the conversion reactions limited their use. In 1976, Wittingham (J. Electrochem. Soc., 123, 315) and Besenhard (J. Power Sources 1(3), 267) finally enabled highly reversible redox reactions by intercalation of lithium ions instead of by chemical conversion. In 1980, Goodenough and Mizushima (Mater. Res. Bull. 15, 783-789) demonstrated a high-energy and high-power LiCoO2 cathode, allowing for an increase of terminal voltage far beyond 3 V. Over the past four decades, the international research community has further developed cathode materials of many varieties. Current state-of-the-art cathodes demonstrate voltages beyond any known electrolyte stability window, bringing electrolyte research once again to the forefront of battery research.

  5. Ultrathin diamond-like carbon films deposited by filtered carbon vacuum arcs

    Energy Technology Data Exchange (ETDEWEB)

    Anders, Andre; Fong, Walton; Kulkarni, Ashok; Ryan, Francis W.; Bhatia, C. Singh

    2001-07-13

    Ultrathin (< 5 nm) hard carbon films are of great interest to the magnetic storage industry as the areal density approaches 100 Gbit/in{sup 2}. These films are used as overcoats to protect the magnetic layers on disk media and the active elements of the read-write slider. Tetrahedral amorphous carbon films can be produced by filtered cathodic arc deposition, but the films will only be accepted by the storage industry only if the ''macroparticle'' issue has been solved. Better plasma filters have been developed over recent years. Emphasis is put on the promising twist filter system - a compact, open structure that operates with pulsed arcs and high magnetic field. Based on corrosion tests it is shown that the macroparticle reduction by the twist filter is satisfactory for this demanding application, while plasma throughput is very high. Ultrathin hard carbon films have been synthesized using S-filter and twist filter systems. Film properties such as hardness, elastic modulus, wear, and corrosion resistance have been tested.

  6. Ultrathin diamond-like carbon films deposited by filtered carbon vacuum arcs

    Energy Technology Data Exchange (ETDEWEB)

    Anders, Andre; Fong, Walton; Kulkarni, Ashok; Ryan, Francis W.; Bhatia, C. Singh

    2001-07-13

    Ultrathin (< 5 nm) hard carbon films are of great interest to the magnetic storage industry as the areal density approaches 100 Gbit/in{sup 2}. These films are used as overcoats to protect the magnetic layers on disk media and the active elements of the read-write slider. Tetrahedral amorphous carbon films can be produced by filtered cathodic arc deposition, but the films will only be accepted by the storage industry only if the ''macroparticle'' issue has been solved. Better plasma filters have been developed over recent years. Emphasis is put on the promising twist filter system - a compact, open structure that operates with pulsed arcs and high magnetic field. Based on corrosion tests it is shown that the macroparticle reduction by the twist filter is satisfactory for this demanding application, while plasma throughput is very high. Ultrathin hard carbon films have been synthesized using S-filter and twist filter systems. Film properties such as hardness, elastic modulus, wear, and corrosion resistance have been tested.

  7. 负压区的存在对刚性陶瓷过滤器脉冲反吹性能的影响%EFFECT OF NEGATIVE PRESSURE REGION ON PULSE-JET CLEANING PERFORMANCE OF RIGID CERAMIC FILTERS

    Institute of Scientific and Technical Information of China (English)

    姬忠礼; 郭建光

    2000-01-01

    利用压电式压力传感器测定了陶瓷过滤器在脉冲反吹过程中滤管内动态压力的变化规律,表明在脉冲反吹快要结束和正常过滤尚未开始的过渡过程中,滤管内存在严重的负压区。利用单个颗粒轨道模型分析了部分已被吹离滤管表面的小颗粒在负压区的作用下会重新返回到滤管壁,从而证实了负压区是影响刚性陶瓷过滤器稳定运行的重要原因。%In a ceramic filter experimental set-up with three filter candles,the dynamic pressures atthe inner wall of one filter candle during pulse-jet cleaning aremeasured by using resize-electric pressure transducer. The experimentalresults show that the dynamic pressure in wholepulse-jet cleaning process consists of two parts. One is the positivepressure in the filter candlegreater than the pressure outside the filter candle whichcorresponds to the outward radial fluidflow to break up and dislodge the dust cake on the surfaceof the filter tube. The other is anegative pressure region which is responsible for inward radialflow while the pulse-jet is closed.The influences of reservoir pressure on thedynamic pressure are discussed.The calculation results of particle motion indicate that negativepressure region cause a fractionof particles removed re-deposit on the candle surface. Especiallyfiner particles is more easierlyre-deposited on the surface to form thin and dense layer on thefilter candle and to increasegradually the residual pressure drop across the candle. It isconcluded that negative pressureregion may have important effects on the long-term stable operation of thefilter unit.

  8. Effect of negative substrate bias on the microstructure and mechanical properties of Ti-Si-N films deposited by a hybrid filtered cathodic arc and ion beam sputtering technique

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Yujuan, E-mail: cnzhangyujuan@yahoo.com.cn [Laboratory of Special Functional Materials, Henan University, Kaifeng 475004 (China); Yang Yingze; Zhai Yuhao; Zhang Pingyu [Laboratory of Special Functional Materials, Henan University, Kaifeng 475004 (China)

    2012-07-01

    A hybrid cathodic arc and ion beam sputtering method was employed to synthesize Ti-Si-N films. The influence of negative substrate bias on the structure and mechanical properties was investigated by using XRD, XPS, HRTEM, nanoindentor and so on. With the increasing of negative bias there is a decrease in the TiN crystallite size from 36 nm to 10 nm. Negative substrate bias promoted the conformation of nc-TiN/a-Si{sub 3}N{sub 4} nanocomposite structure with complete phase separation and uniform crystallite size. Superhard TiSiN films with a maximum hardness of 46 GPa were successfully synthesized under 100 V negative bias. Severe oxidation occurred in films deposited under 200 V and 300 V negative substrate bias due to the decreasing of deposition rate, which led to the hardness of films reduced to the value of 26 GPa and 22 GPa respectively.

  9. Advanced Cathode Electrolyzer (ACE) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation is a static, cathode-fed, 2000 psi, balanced-pressure Advanced Cathode Electrolyzer (ACE) based on PEM electrolysis technology. It...

  10. Advanced Cathode Electrolyzer (ACE) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation is a static, cathode-fed, 2000 psi, balanced-pressure Advanced Cathode Electrolyzer (ACE) based on PEM electrolysis technology. It...

  11. Highly Efficient Micro Cathode Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Busek Company, Inc. proposes to develop a micro thermionic cathode that requires extremely low power and provides long lifetime. The basis for the cathode is a...

  12. Cathode material for lithium batteries

    Science.gov (United States)

    Park, Sang-Ho; Amine, Khalil

    2013-07-23

    A method of manufacture an article of a cathode (positive electrode) material for lithium batteries. The cathode material is a lithium molybdenum composite transition metal oxide material and is prepared by mixing in a solid state an intermediate molybdenum composite transition metal oxide and a lithium source. The mixture is thermally treated to obtain the lithium molybdenum composite transition metal oxide cathode material.

  13. Electrochemical cells and cathode materials

    Energy Technology Data Exchange (ETDEWEB)

    Skarstad, P.M.; Untereker, D.F.; Meritt, D.R.

    1988-08-02

    This patent describes an electrochemical cell comprising anode and cathode means in operative relationship. The cathode means comprising a cathode material comprised of, at least in part: a halogen component selected from the group consisting of iodine, bromine, iodine bromide and mixtures thereof, and poly(ethylene oxide), at least in part.

  14. SOFC Cathode Mechanisms

    DEFF Research Database (Denmark)

    Jacobsen, Torben; Zachau-Christiansen, Birgit; Bay, Lasse

    1996-01-01

    The transient response of SOFC oxygen cathodes shows a characteristic inductive hysteresis and correspondingly the impedance diagram combines one or two capacitive arcs with a low frequency inductive arc. These features are discussed on the basis of a three step reaction sequence taken from...

  15. Smart cathodic protection systems

    NARCIS (Netherlands)

    Polder, R.B.; Leggedoor, J.; Schuten, G.; Sajna, S.; Kranjc, A.

    2010-01-01

    Cathodic protection delivers corrosion protection in concrete structures exposed to aggressive environments, e.g. in de-icing salt and marine climates. Working lives of a large number of CP systems are at least more than 13 years and probably more than 25 years, provided a minimum level of maintenan

  16. Using Multispectral Imaging to Measure Temperature Profiles and Emissivity of Large Thermionic Dispenser, Cathodes

    Energy Technology Data Exchange (ETDEWEB)

    D.F. Simmons; C.M. Fortgang; D.B. Holtkamp

    2001-09-01

    Thermionic dispenser cathodes are widely used in modern high-power microwave tubes. Use of these cathodes has led to significant improvement in performance. In recent years these cathodes have been used in electron linear accelerators (LINACs), particularly in induction LINACs, such as the Experimental Test Accelerator at Lawrence Livermore National Laboratory and the Relativistic Test Accelerator at Lawrence Berkeley National Laboratory. For induction LINACs, the thermionic dispenser cathode provides greater reproducibility, longer pulse lengths, and lower emittance beams than does a field emission cathode. Los Alamos National Laboratory is fabricating a dual-axis X-ray radiography machine called dual-axis radiograph hydrodynamic test (DARHT). The second axis of DARHT consists of a 2-kA, 20-MeV induction LINAC that uses a 3.2-MeV electron gun with a tungsten thermionic-dispenser cathode. Typically the DARHT cathode current density is 10 A/cm{sup 2} at 1050 C. Under these conditions current density is space-charge limited, which is desirable since current density is independent of temperature. At lower temperature (the temperature-limited regime) there are variations in the local current density due to a nonuniform temperature profile. To obtain the desired uniform current density associated with space-charge limited operation, the coolest area on the cathode must be at a sufficiently high temperature so that the emission is space-charge limited. Consequently, the rest of the cathode is emitting at the same space-charge-limited current density but is at a higher temperature than necessary. Because cathode lifetime is such a strong function of cathode temperature, there is a severe penalty for nonuniformity in the cathode temperature. For example, a temperature increase of 50 C means cathode lifetime will decrease by a factor of at least four. Therefore, we are motivated to measure the temperature profiles of our large-area cathodes.

  17. 50 Hz electron emission from PZT ferro-electric cathodes

    Energy Technology Data Exchange (ETDEWEB)

    Flechtner, D.; Golkowski, C.; Ivers, J.D.; Kerslick, G.S.; Nation, J.A.; Schachter, L. [Cornell Univ., Ithaca, NY (United States)

    1997-12-31

    Ferro-electric cathodes may offer a source of high current density electron beams for applications where the use of conventional field emitters is limited by repetition rate and lifetime. In a ferro-electric cathode, electrons are emitted when the spontaneous polarization is rapidly changed by a pulsed electric field applied across the ferroelectric. When no additional voltage is applied to a planar diode gap, emission current densities are on the order of 1 A/cm{sup 2}. When an additional field is applied to the gap, the authors have measured current densities up to 100 A/cm{sup 2}. In a new configuration that permits beam extraction into a drift tube, the cathode is pulsed 10--20kV negative and electron current densities of {approximately}20 A/cm{sup 2} at repetition rates up to {approximately}50 Hz (power supply limited) have been measured. The one inch diameter ferro-electric cathode is located in the fringing region of a 1.5 kG solenoid magnetic field {approximately}2.8 cm from the entrance of a grounded drift tube. A Faraday cup is located several centimeters inside the drift tube and measurements show that repeatable beam current can be extracted from the ferroelectric cathode in this geometry.

  18. High-current carbon-epoxy capillary cathode

    Science.gov (United States)

    Gleizer, J. Z.; Queller, T.; Bliokh, Yu.; Yatom, S.; Vekselman, V.; Krasik, Ya. E.; Bernshtam, V.

    2012-07-01

    The results of experiments on the reproducible generation of an electron beam having a high current density of up to 300 A/cm2 and a satisfactorily uniform cross-sectional distribution of current density in a ˜200 kV, ˜450 ns vacuum diode with a carbon-epoxy capillary cathode are presented. It was found that the source of the electrons is the plasma formed as a result of flashover inside the capillaries. It is shown that the plasma formation occurs at an electric field ≤15 kV/cm and that the cathode sustains thousands of pulses without degradation in its emission properties. Time- and space-resolved visible light observation and spectroscopy analyses were used to determine the cathode plasma's density, temperature, and expansion velocity. It was found that the density of the cathode plasma decreases rapidly in relation to the distance from the cathode. In addition, it was found that the main reason for the short-circuiting of the accelerating gap is the formation and expansion of the anode plasma. Finally, it was shown that when an external guiding magnetic field is present, the injection of the electron beam into the drift space with a current amplitude exceeding its critical value changes the radial distribution of the current density of the electron beam because the inner electrons are reflected from the virtual cathode.

  19. Cesiated hollow cathodes in the multicusp ion source

    Science.gov (United States)

    Belchenko, Yu. I.; Oka, Y.; Hamabe, M.; Kaneko, O.; Krivenko, A.; Takeiri, Y.; Tsumori, K.; Osakabe, M.; Ikeda, K.; Asano, E.; Kawamoto, T.

    2002-02-01

    A cesiated hydrogen hollow cathode (CHC) was tested for plasma injection in the multicusp negative ion source (MS). The CHC arc with hydrogen feed and cesium seeding through the CHC volume was explored. One cathode unit (40 mm length, 19 mm in diameter, emission opening area 1-3 mm2) with no special cooling provided the MS discharge operation with direct current up to 30 A, and up to 60 A in the long-pulse mode. High efficiency of negative ion production in the MS discharge, driven by a CHC plasma injection was recorded.

  20. Numerical Simulation of Fluid Field in Injection Pipe of Pulse-jet Bag Filter%脉冲袋式除尘器喷吹管内流场的模拟研究

    Institute of Scientific and Technical Information of China (English)

    蒋明辉

    2011-01-01

    脉冲袋式除尘器清灰时,传统等孔径喷吹管各喷口喷气量的不均匀,将导致沿喷吹管方向滤袋清灰效果不同,清灰效果差。本文针对等孔径喷吹管喷吹过程,利用CFD软件进行非稳态模拟,得到了喷吹充分发展时刻的管内气流速度、静压分布,以及喷吹管各喷口的气体质量流量。最后用修正方法对喷吹管喷口尺寸进行优化设计,提高了喷吹气流均匀性,为脉冲袋式除尘器喷吹系统的改进提供了理论依据。%Because of the mass flux non-uniform distribution of nozzles in injection pipe,the effect of pulse-jet cleaning system for each filter-bag is different.It causes the drop of the cleaning efficiency.In this paper,the computational fluid dynamics software is used to simulate the unsteady fluid field of the same nozzle radius distributed injection pipe.The distributions of static pressure,flow velocity and mass flow rate are gained when fluid field is fully developed,and the design of the nozzles of injection pipe is optimized.All of these offered a reference to the design and improvement of pulse-jet bag filter.

  1. Experimental Investigation of Pulsed Nanosecond Streamer Discharges for CO2 Reforming

    Science.gov (United States)

    Pachuilo, Michael; Levko, Dima; Raja, Laxminarayan; Varghese, Philip

    2016-09-01

    Rapid global industrialization has led to an increase in atmospheric greenhouse gases, specifically carbon dioxide levels. Plasmas present a great potential for efficient reforming of greenhouse gases. There are several plasma discharges which have been reported for reforming process: dielectric barrier discharges (DBD), microwave discharges, and glide-arcs. Microwave discharges have CO2 conversion energy efficiency of up to 40% at atmospheric conditions, while glide-arcs have 43% and DBD 2-10%. In our study, we analyze a single nanosecond pulsed cathode directed streamer discharge in CO2 at atmospheric pressure and temperature. We have conducted time resolved imaging with spectral bandpass filters of a streamer discharge with an applied negative polarity pulse. The image sequences have been correlated to the applied voltage and current pulses. From the spectral filters we can determine where spatially and temporally excited species are formed. In this talk we report on spectroscopic studies of the discharge and estimate plasma properties such as temperature and density of excited species and electrons. Furthermore, we report on the effects of pulse polarity as well as anodic streamer discharges on the CO2 conversion efficiency. Finally, we will focus on the effects of vibrational excitation on carbon dioxide reforming efficiency for streamer discharges. Our experimental results will be compared with an accompanying plasma computational model studies.

  2. Pulse on Pulse

    DEFF Research Database (Denmark)

    Schmidt, Ulrik; Carlson, Merete

    2012-01-01

    Pulse on Pulse” investigates the relation between signifying processes and non-signifying material dynamism in the installation Pulse Room (2006-) by Mexican Canadian artist Rafael Lozano-Hemmer. In Pulse Room the sense of pulse is ambiguous. Biorhythms are transmitted from the pulsing energy...... and pulsating ‘room’. Hence, the visitors in Pulse Room are invited into a complex scenario that continuously oscillates between various aspects of signification (the light bulbs representing individual lives; the pulse itself as the symbolic ‘rhythm of life’) and instants of pure material processuality...... a multilayered sense of time and space that is central to the sensory experience of Pulse Room as a whole. Pulse Room is, at the very same time, an anthropomorfized archive of a past intimacy and an all-encompassing immersive environment modulating continuously in real space-time....

  3. Filter arrays

    Energy Technology Data Exchange (ETDEWEB)

    Page, Ralph H.; Doty, Patrick F.

    2017-08-01

    The various technologies presented herein relate to a tiled filter array that can be used in connection with performance of spatial sampling of optical signals. The filter array comprises filter tiles, wherein a first plurality of filter tiles are formed from a first material, the first material being configured such that only photons having wavelengths in a first wavelength band pass therethrough. A second plurality of filter tiles is formed from a second material, the second material being configured such that only photons having wavelengths in a second wavelength band pass therethrough. The first plurality of filter tiles and the second plurality of filter tiles can be interspersed to form the filter array comprising an alternating arrangement of first filter tiles and second filter tiles.

  4. 喷吹压力与喷吹距离对长滤袋清灰效果的研究%Effect of the pulse pressure and the jet distance on the cleaning performance of the long pulse-jet filter bag

    Institute of Scientific and Technical Information of China (English)

    吕娟; 颜翠平; 袁彩云; 付瑜; 李雪; 陈海焱

    2016-01-01

    The present paper is aimed at introducing its investigation results on the effects of the pulse pressure and the jet distance on the cleaning performance of the long pulse-jet filter bag in order to promote the optimistic design for a semi-industrial pulse-jet filter bag.For the aforementioned purpose,we have adopted the peak pressure and the speed to arrive at the peak pressure as the idealistic indexes for the evaluation of the pulse cleaning effects.In doing so,we have adopted 8 high precision piezoelectric pressure transducers (according to Model QSY8135)to examine and measure the peak pressure and the time for reaching the peak pressure to be shown on the internal surface of the filter bag (160 mm ×6 000 mm),which is made of the polyester needle-felt.The evaluation results have shown that it would be possible to realize the optimum design in a semi-industrial pulsejet filter bag when the pulse pressure is set on 0.1-0.3 MPa in a distance of 200 mm.Our investigation has also proven that the peak pressure tends to increase from the top opening and then reach the maximum value at the location of 1 m in the length of the filter bag.And then,the peak pressure would like to drop gradually,and later to rise again at the bottom of the filter bag on its surface.Thus,the peak pressure distribution tends to be uneven along its surface and it would take 0 to 4 000 mm to reach its peak pressure in its length and decrease from 4 000 mm to 6 000mm,with the average peak pressure values along its length being 2.076 8 kPa,3.292 1 kPa and 4.325 2 kPa,on the condition that the pulse pressure keeps at 0.1-0.3 MPa and the distance stays at 200 mm,respectively.What is more,with the average peak pressures obtained under the optimum parameter design condition,the pulse cleaning results prove to be suitable for practical applications.Thus,it can be concluded that the investigation and experiments we have done can not only be expected to lay a theoretical basis for the study of the

  5. Digital hum filtering

    Science.gov (United States)

    Knapp, R.W.; Anderson, N.L.

    1994-01-01

    Data may be overprinted by a steady-state cyclical noise (hum). Steady-state indicates that the noise is invariant with time; its attributes, frequency, amplitude, and phase, do not change with time. Hum recorded on seismic data usually is powerline noise and associated higher harmonics; leakage from full-waveform rectified cathodic protection devices that contain the odd higher harmonics of powerline frequencies; or vibrational noise from mechanical devices. The fundamental frequency of powerline hum may be removed during data acquisition with the use of notch filters. Unfortunately, notch filters do not discriminate signal and noise, attenuating both. They also distort adjacent frequencies by phase shifting. Finally, they attenuate only the fundamental mode of the powerline noise; higher harmonics and frequencies other than that of powerlines are not removed. Digital notch filters, applied during processing, have many of the same problems as analog filters applied in the field. The method described here removes hum of a particular frequency. Hum attributes are measured by discrete Fourier analysis, and the hum is canceled from the data by subtraction. Errors are slight and the result of the presence of (random) noise in the window or asynchrony of the hum and data sampling. Error is minimized by increasing window size or by resampling to a finer interval. Errors affect the degree of hum attenuation, not the signal. The residual is steady-state hum of the same frequency. ?? 1994.

  6. Digital Poly-phase Filtering and Pulse Compression of PN-code Fuze%伪码引信的数字多相滤波和频域脉冲压缩

    Institute of Scientific and Technical Information of China (English)

    徐利平; 谢锡海; 曹志谦; 郑小燕

    2009-01-01

    In order to overcome the shortcoming of the time-domain correlation processing in classical PN-code fuze, the method of digital quadrature detection is proposed based on poly-phase filtering and digital pulse com-pression which are achieved by FPGA and DSP tools. The FPGA-DSP simulation results are indicated to be accu-rate according to the comparison with the results simulated by the MATLAB. Digital pulse compression tech-nique will be the trend of modern pulse compression technique because of its stable performance, strong anti-in-terference ability, flexible control mode and miniaturized hardware system.%针对传统伪随机码引信对回波信号时域相关处理法在处理大点数、大压缩比信号时的不足,提出采用软件无线电技术中的多相滤波数字正交检波器和频域数字脉冲压缩的方法.分别使用FPGA和DSP实现多相滤波数字正交检波器以及频域数字脉冲压缩.对FPGA及DSP进行的仿真与Matlab对整个过程仿真的结果比较,误差极小,验证了理论的正确性.数字脉压技术以其性能稳定、抗干扰能力强、控制方式灵活和硬件系统小型化等优点,逐步取代早期的模拟脉压技术,是现代脉压技术的发展趋势.

  7. Measurement and analysis of thermal photoemission from a dispenser cathode

    Science.gov (United States)

    Jensen, Kevin L.; Feldman, Donald W.; Virgo, Matt; O'Shea, Patrick G.

    2003-08-01

    Photocathodes for free electron lasers (FELs) are required to produce nano-Coulomb pulses in picosecond time scales with demonstrable reliability, lifetime, and efficiency. Dispenser cathodes, traditionally a rugged and long-lived thermionic source, are under investigation to determine their utility as a photocathode and have shown promise. The present study describes theoretical models under development to analyze experimental data from dispenser cathodes and to create predictive time-dependent models to predict their performance as an FEL source. Here, a steady-state model of a dispenser cathode with partial coverage of a low work function coating and surface nonuniformity is developed. Quantitative agreement is found for experimental data, especially with regard to temperature, field, laser intensity, and quantum efficiency versus laser wavelength dependence. In particular, for long wavelength incident lasers of sufficient intensity, the majority of the absorbed energy heats the electron gas and background lattice, and photoemission from the heated electron distribution constitutes the emitted current.

  8. Discharge state transition and cathode fall thickness evolution during chromium HiPIMS discharge

    Science.gov (United States)

    Zuo, Xiao; Ke, Peiling; Chen, Rende; Li, Xiaowei; Odén, Magnus; Wang, Aiying

    2017-08-01

    The temporal evolutions of target voltage and current waveforms under different pulse voltage and working pressure conditions were studied during Cr high power impulse magnetron sputtering discharges. Target voltage and current characteristics demonstrated that when the pulse width was set as 200 μs, HiPIMS discharge went through a four-stage sequence during each pulse, Townsend discharge, glow discharge, afterglow, and pulse-off stages. A discharge state transition in the glow discharge stage happened at high pulse voltage and working pressure conditions. Furthermore, the dependence of reduced cathode fall thickness pdc on pulse voltage, working pressure, and normalized current density j/p2 was presented. It was found that gas rarefaction leads to a change of relationship between pdc and j/p2. A noticeable increase of the cathode fall thickness caused by gas rarefaction has been found.

  9. Unusual Cathode Erosion Patterns Observed for Steered Arc Sources

    CERN Document Server

    Kolbeck, Jonathan

    2014-01-01

    A cathodic arc source with a magnetron-type magnetic field was investigated for stability, erosion, and compatibility with a linear macroparticle filter. Here we report about unusual arc spot erosion patterns, which were narrow (~ 2 mm) with periodic pits when operating in argon, and broad (~ 10 mm) with periodic groves and ridges when operating in an argon and oxygen mixtures. These observations can be correlated with the ignition probability for type 2 and type 1 arc spots, respectively.

  10. Pulse on Pulse

    DEFF Research Database (Denmark)

    Schmidt, Ulrik; Carlson, Merete

    2012-01-01

    and pulsating ‘room’. Hence, the visitors in Pulse Room are invited into a complex scenario that continuously oscillates between various aspects of signification (the light bulbs representing individual lives; the pulse itself as the symbolic ‘rhythm of life’) and instants of pure material processuality......“Pulse on Pulse” investigates the relation between signifying processes and non-signifying material dynamism in the installation Pulse Room (2006-) by Mexican Canadian artist Rafael Lozano-Hemmer. In Pulse Room the sense of pulse is ambiguous. Biorhythms are transmitted from the pulsing energy...... of the visitor’s beating heart to the blink of a fragile light bulb, thereby transforming each light bulb into a register of individual life. But at the same time the blinking light bulbs together produce a chaotically flickering light environment composed by various layers of repetitive rhythms, a vibrant...

  11. High-current long-duration uniform electron beam generation in a diode with multicapillary carbon-epoxy cathode

    Energy Technology Data Exchange (ETDEWEB)

    Queller, T.; Gleizer, J. Z.; Krasik, Ya. E. [Physics Department, Technion, Haifa 32000 (Israel)

    2013-09-28

    The results of reproducibly generating an electron beam with a current density of up to 5 kA/cm{sup 2}, without the cathode-anode gap being shorted by the plasma formed inside the cathode carbon-epoxy capillaries, in a ∼350 kV, ∼600 ns diode, with and without an external guiding magnetic field, are presented. The cathode sustained hundreds of pulses without degradation of its emission properties. Time- and space-resolved emissions of the plasma and spectroscopy analyses were used to determine the cathode plasma's density, temperature, and expansion velocity.

  12. High-current long-duration uniform electron beam generation in a diode with multicapillary carbon-epoxy cathode

    Science.gov (United States)

    Queller, T.; Gleizer, J. Z.; Krasik, Ya. E.

    2013-09-01

    The results of reproducibly generating an electron beam with a current density of up to 5 kA/cm2, without the cathode-anode gap being shorted by the plasma formed inside the cathode carbon-epoxy capillaries, in a ˜350 kV, ˜600 ns diode, with and without an external guiding magnetic field, are presented. The cathode sustained hundreds of pulses without degradation of its emission properties. Time- and space-resolved emissions of the plasma and spectroscopy analyses were used to determine the cathode plasma's density, temperature, and expansion velocity.

  13. Nanostructured lanthanum manganate composite cathode

    DEFF Research Database (Denmark)

    Wang, Wei Guo; Liu, Yi-Lin; Barfod, Rasmus

    2005-01-01

    that the (La1-xSrx)(y)MnO3 +/-delta (LSM) composite cathodes consist of a network of homogenously distributed LSM, yttria-stabilized zirconia (YSZ), and pores. The individual grain size of LSM or YSZ is approximately 100 nm. The degree of contact between cathode and electrolyte is 39% on average. (c) 2005...

  14. Cathodic hydrodimerization of nitroolefins

    Directory of Open Access Journals (Sweden)

    Michael Weßling

    2015-07-01

    Full Text Available Nitroalkenes are easily accessible in high variety by condensation of aldehydes with aliphatic nitroalkanes. They belong to the group of activated alkenes that can be hydrodimerized by cathodic reduction. There are many olefins with different electron withdrawing groups used for cathodic hydrodimerization, but not much is known about the behaviour of the nitro group. Synthetic applications of this group could profit from the easy access to nitroolefins in large variety, the C–C bond formation with the introduction of two nitro groups in a 1,4-distance and the conversions of the nitro group by reduction to oximes and amines, the conversion into aldehydes and ketones via the Nef reaction and base catalyzed condensations at the acidic CH bond. Eight 1-aryl-2-nitro-1-propenes have been electrolyzed in an undivided electrolysis cell to afford 2,5-dinitro-3,4-diaryl hexanes in high yield. The 4-methoxy-, 4-trifluoromethyl-, 2-chloro- and 2,6-difluorophenyl group and furthermore the 2-furyl and 2-pyrrolyl group have been applied. The reaction is chemoselective as only the double bond but not the nitro group undergoes reaction, is regioselective as a ß,ß-coupling with regard to the nitro group and forms preferentially two out of six possible diastereomers as major products.

  15. Cathodic hydrodimerization of nitroolefins.

    Science.gov (United States)

    Weßling, Michael; Schäfer, Hans J

    2015-01-01

    Nitroalkenes are easily accessible in high variety by condensation of aldehydes with aliphatic nitroalkanes. They belong to the group of activated alkenes that can be hydrodimerized by cathodic reduction. There are many olefins with different electron withdrawing groups used for cathodic hydrodimerization, but not much is known about the behaviour of the nitro group. Synthetic applications of this group could profit from the easy access to nitroolefins in large variety, the C-C bond formation with the introduction of two nitro groups in a 1,4-distance and the conversions of the nitro group by reduction to oximes and amines, the conversion into aldehydes and ketones via the Nef reaction and base catalyzed condensations at the acidic CH bond. Eight 1-aryl-2-nitro-1-propenes have been electrolyzed in an undivided electrolysis cell to afford 2,5-dinitro-3,4-diaryl hexanes in high yield. The 4-methoxy-, 4-trifluoromethyl-, 2-chloro- and 2,6-difluorophenyl group and furthermore the 2-furyl and 2-pyrrolyl group have been applied. The reaction is chemoselective as only the double bond but not the nitro group undergoes reaction, is regioselective as a ß,ß-coupling with regard to the nitro group and forms preferentially two out of six possible diastereomers as major products.

  16. Compact lanthanum hexaboride hollow cathode.

    Science.gov (United States)

    Goebel, Dan M; Watkins, Ronald M

    2010-08-01

    A compact lanthanum hexaboride hollow cathode has been developed for space applications where size and mass are important and research and industrial applications where access for implementation might be limited. The cathode design features a refractory metal cathode tube that is easily manufactured, mechanically captured orifice and end plates to eliminate expensive e-beam welding, graphite sleeves to provide a diffusion boundary to protect the LaB6 insert from chemical reactions with the refractory metal tube, and several heater designs to provide long life. The compact LaB(6) hollow cathode assembly including emitter, support tube, heater, and keeper electrode is less than 2 cm in diameter and has been fabricated in lengths of 6-15 cm for different applications. The cathode has been operated continuously at discharge currents of 5-60 A in xenon. Slightly larger diameter versions of this design have operated at up to 100 A of discharge current.

  17. Development and Experimental Operation of a Flashboard Plasma Cathode Test Stand

    Science.gov (United States)

    2012-06-01

    Bixier, M. Krishnan, and D. Huet, “Density measurements in flash board plasmas for a magnetically confined plasma opening switch ,” in Pulsed Power...of HPMWs ........................................................ 3  C.  BACKGROUND OF CATHODES AND THEIR LIMITATIONS ............ 6  1.  Thermionic ...HPM system ...... 4  Figure 2.  Illustration of a thermionic cathode in an electron gun (From [11]) ....... 6  Figure 3.  Photoelectric emission from

  18. Contactor/filter improvements

    Science.gov (United States)

    Stelman, David

    1989-01-01

    A contactor/filter arrangement for removing particulate contaminants from a gaseous stream includes a housing having a substantially vertically oriented granular material retention member with upstream and downstream faces, a substantially vertically oriented microporous gas filter element, wherein the retention member and the filter element are spaced apart to provide a zone for the passage of granular material therethrough. The housing further includes a gas inlet means, a gas outlet means, and means for moving a body of granular material through the zone. A gaseous stream containing particulate contaminants passes through the gas inlet means as well as through the upstream face of the granular material retention member, passing through the retention member, the body of granular material, the microporous gas filter element, exiting out of the gas outlet means. Disposed on the upstream face of the filter element is a cover screen which isolates the filter element from contact with the moving granular bed and collects a portion of the particulates so as to form a dust cake having openings small enough to exclude the granular material, yet large enough to receive the dust particles. In one embodiment, the granular material is comprised of prous alumina impregnated with CuO, with the cover screen cleaned by the action of the moving granular material as well as by backflow pressure pulses.

  19. High-current electron beam generation in a diode with a multicapillary dielectric cathode

    Science.gov (United States)

    Gleizer, J. Z.; Hadas, Y.; Gurovich, V. Tz.; Felsteiner, J.; Krasik, Ya. E.

    2008-02-01

    Results of high-current electron beam generation in an ˜200kV, ˜250ns diode with a multicapillary dielectric cathode (MCDC) assisted by either velvet-type or ferroelectric plasma sources (FPSs) are presented. Multicapillary cathodes made of cordierite, glass, and quartz glass samples were studied. It was found that the source of electrons is the plasma ejected from capillaries. The plasma parameters inside capillary channels and in the vicinity of the cathode surface were determined during the accelerating pulse using visible range spectroscopy. It was shown that glass multicapillary cathodes are characterized by less surface erosion than the cordierite cathodes. Also, it was found that multicapillary cathodes assisted by a FPS showed longer lifetime and better vacuum compatibility than multicapillary cathodes assisted by a velvet-type igniter. Finally, it was found that quartz glass MCDC assisted by FPS is characterized by almost simultaneous formation of the plasma in a cross-sectional area of the dielectric sample with respect to the beginning of the accelerating pulse. The latter is explained by intense UV radiation which synchronized formation of parallel discharges due to induced secondary electron emission.

  20. Optimal filtering

    CERN Document Server

    Anderson, Brian D O

    2005-01-01

    This graduate-level text augments and extends beyond undergraduate studies of signal processing, particularly in regard to communication systems and digital filtering theory. Vital for students in the fields of control and communications, its contents are also relevant to students in such diverse areas as statistics, economics, bioengineering, and operations research.Topics include filtering, linear systems, and estimation; the discrete-time Kalman filter; time-invariant filters; properties of Kalman filters; computational aspects; and smoothing of discrete-time signals. Additional subjects e

  1. Further developed filter systems for keeping the air clean

    Energy Technology Data Exchange (ETDEWEB)

    Hochstrat, W.B.

    1978-12-01

    The pulse-jet filter system is presented in this contribution. The development of improved fibers to produce high-quality needle felting was the basis for surface filters as well as tube filters. The system tube filter with pressurized-air cleaning is described in greater detail. Its advantage besides good degrees of separation is especially the little maintenance required.

  2. An analysis of the anomalous high-current cathode emission in pseudospark and back-of-the-cathode lighted thyratron switches

    Science.gov (United States)

    Hartmann, W.; Dominic, V.; Kirkman, G. F.; Gundersen, M. A.

    1989-06-01

    An analysis of the anomalously large cathode emission recently observed in the superdense glow of pseudospark and back-lighted thyratrons is presented. These switches are low-pressure (27 PaH2) glow-discharge pulsed-power devices. After operating at peak discharge currents of 6 to 8 kA and pulse durations of 0.5 to 1 microsec., the surface surrounding the cathode hole was found to have been homogeneously melted within a radius of approx. 4 mm indicating that the discharge is a superdense glow discharge, not an arc, with a cross-sectional area on the order of 1 sq cm. This conclusion is also supported by streak camera measurements. The current density at the cathode surface under these conditions is 5 to 10 kA/sq cm, several orders of magnitude larger than that of thermionic cathodes in common thyratrons. This high-current density is explained by intense cathode heating from a high-current density ion beam produced in the cathode fall during the initial stage of current buildup. The surface heating resulting from this beam yields a significant field-enhanced thermionic emission of electrons.

  3. Motion of a virtual cathode in a cylindrical channel with electron beam transport in the “compressed” state

    Energy Technology Data Exchange (ETDEWEB)

    Belomyttsev, S. Ya.; Grishkov, A. A.; Tsygankov, R. V. [Institute of High Current Electronics SB RAS, 2/3 Akademichesky Ave., 634055 Tomsk (Russian Federation); Kurkan, I. K., E-mail: ikk@lfe.hcei.tsc.ru [Institute of High Current Electronics SB RAS, 2/3 Akademichesky Ave., 634055 Tomsk (Russian Federation); National Research Tomsk Polytechnic University, 30 Lenin Ave., 634050 Tomsk (Russian Federation)

    2014-03-15

    This paper studies the motion of a virtual cathode in a two-section drift tube with the formation and breakup of the “compressed” state of an electron beam. Experimental arrangements to intercept part of the injected current during the voltage pulse and to provide virtual cathode motion toward the collector are proposed. The arrangements were implemented on the SINUS-7 high-current electron accelerator. Theoretical and experimental dependences of the virtual cathode velocity on the injected current and cathode voltage are presented. The experimental data on virtual cathode motion agree with its theoretical model based on analytical solutions of equations assisted by computer simulation with the PIC code KARAT. The results of the work demonstrate the feasibility of controlling the virtual cathode motion which can be used in collective ion acceleration and microwave generation.

  4. LiCoO{sub 2} and LiCo{sub 1-x}Al{sub x}O{sub 2} thin film cathodes grown by pulsed laser ablation

    Energy Technology Data Exchange (ETDEWEB)

    Perkins, J.D.; Bahn, C.S.; Parilla, P.A.; Duncan, M.; Yu, H.; Ginley, D.S. [National Renewable Energy Lab., Golden, CO (United States); McGraw, J.M. [Colorado School of Mines, Golden, CO (United States); Fu, M.L. [Colorado Univ., Boulder, CO (United States)

    1999-09-01

    LiCoO{sub 2} and LiCo{sub 0.5}Al{sub 0.5}O{sub 2} thin films have been grown by pulsed laser ablation on SnO{sub 2}-coated glass substrates. For both stoichiometries, the resultant films are dense and uniaxially textured films with the Li and Co layers parallel to the substrate. In general, to grow LiCo{sub 0.5}Al{sub 0.5}O{sub 2} films, a laser flux roughly 80 mJ pulse{sup -1} higher than that used for LiCoO{sub 2} films is required to achieve a similar deposition rate. LiCoO{sub 2} films grown at T{sub s}=600 C and p[O{sub 2}]=2000 mTorr have a typical grain size of {proportional_to}100 nm. For constant current cycling between 3.8 and 4.2 V at 5 {mu}A, the LiCoO{sub 2} films have an initial discharge capacity of {proportional_to}0.33 Li per LiCoO{sub 2} (89 (mA h) g{sup -1}) decreasing to {proportional_to}0.18 Li/LiCoO{sub 2} (49 (mA h) g{sup -1}) after 100 cycles and have a continued capacity loss of {proportional_to}0.25% per cycle. The LiCo{sub 0.5}Al{sub 0.5}O{sub 2} films grown to date have roughly 3 times less capacity than the LiCoO{sub 2} films and apparently a large asymmetry between Li extraction and reintercalation. (orig.)

  5. Multi-Kiloampere, Electron-Beam Generation from Bare Aluminum Photo-Cathodes Driven by an ArF Laser

    Science.gov (United States)

    Carlson, R. L.; Ridlon, R. N.; Seitz, G. J.; Shurter, R. P.

    1997-05-01

    An electron-beam-pumped laser operating at ArF (193 nm) and 3.5 joules in a 150-ns pulse has been used to illuminate a bare aluminum cathode. The cathode was pulsed to 2.75 MV with fields up to 185 kV/cm using the REX (a 4-MeV, 5-kA, 100-ns pulsed diode) accelerator. Extracted current versus laser power gives a quantum efficiency of 0.1 %. The background vacuum pressure needed for this type of cathode is in the mid 10-6 torr range and 100-ns-long electron beams of several kA have been produced. Both emission limited (current follows laser pulse) and space-charge-limited (current follows pulsed power) regimes have been studied up to 100 Amps/cm^2 by varying the cathode diameter and A-K gap distance. A small-scale test stand has demonstrated a quantum efficiency increase of 2.5 times by thermally augmentating the surface temperature to about 150^0 C. Beam temperature from present velvet based cathodes has been extensively measured to be about 100 eV; measurements of the ArF laser irradiated aluminum cathode indicate a reduction in source temperature of greater than an order of magnitude.

  6. Artificial spectral filtering in dissipative soliton fiber lasers with invisible bandpass filters

    Institute of Scientific and Technical Information of China (English)

    Kong Ling-Jie; Xiao Xiao-Sheng; Yang Chang-Xi

    2012-01-01

    We numerically study the artificial spectral-filtering effect in dissipative soliton fiber lasers without intracavity spectral filters.It is found that in dissipative soliton lasers with real saturable absorbers (SAs),the dynamic spectral filtering of the real SAs serves as an artificial spectral filter and contributes to the pulse shaping.While in the dissipative soliton lasers with artificial SAs,such as nonlinear polarization rotation,the spectral filtering introduced by the intracavity polarization-dependent components acts as an artificial spectral filter and shapes the pulses to obtain modelocking. An investigation of the artificial spectral-filtering effect reveals the operating mechanisms of the dissipative soliton fiber lasers without visible bandpass filters.

  7. Interaction of femtosecond laser pulses with metal photocathode

    Institute of Scientific and Technical Information of China (English)

    Liu Yun-Quan; Zhang Jie; Liang Wen-Xi

    2005-01-01

    The features of interaction of femtosecond laser pulses with photocathode are studied theoretically in this paper.The surface temperature of the metal cathode film while femtosecond laser pulses irradiation is studied with twotemperature model. With a simple photoelectric model we obtain the optimum metal film thickness for the backilluminated photocathode. The generated ultrashort photocurrent pulses are strongly dependent on the temperature of the electron gas and the lattice during the femtosecond laser pulse irradiation on the photocathode.

  8. Hollow Cathode With Multiple Radial Orifices

    Science.gov (United States)

    Brophy, John R.

    1992-01-01

    Improved hollow cathode serving as source of electrons has multiple radial orifices instead of single axial orifice. Distributes ion current more smoothly, over larger area. Prototype of high-current cathodes for ion engines in spacecraft. On Earth, cathodes used in large-diameter ion sources for industrial processing of materials. Radial orientation of orifices in new design causes current to be dispersed radially in vicinity of cathode. Advantageous where desireable to produce plasma more nearly uniform over wider region around cathode.

  9. Back bombardment for dispenser and lanthanum hexaboride cathodes

    Directory of Open Access Journals (Sweden)

    Mahmoud Bakr

    2011-06-01

    Full Text Available The back bombardment (BB effect limits wide usage of thermionic rf guns. The BB effect induces not only ramping-up of a cathode’s temperature and beam current, but also degradation of cavity voltage and beam energy during a macropulse. This paper presents a comparison of the BB effect for the case of dispenser tungsten-base (DC and lanthanum hexaboride (LaB_{6} thermionic rf gun cathodes. For each, particle simulation codes are used to simulate the BB effect and electron beam dynamics in a thermionic rf gun cathode. A semiempirical equation is also used to investigate the stopping range and deposited heat power of BB electrons in the cathode material. A numerical simulation method is used to calculate the change of the cathode temperature and current density during a single macropulse. This is done by solving two differential equations for the rf gun cavity equivalent circuit and one-dimensional thermal diffusion equation. High electron emission and small beam size are required for generation of a high-brightness electron beam, and so in this work the emission properties of the cathode are taken into account. Simulations of the BB effect show that, for a pulse of 6  μs duration, the DC cathode experiences a large change in the temperature compared with LaB_{6}, and a change in current density 6 times higher. Validation of the simulation results is performed using experimental data for beam current beyond the gun exit. The experimental data is well reproduced using the simulation method.

  10. Properties of ceramic candle filters

    Energy Technology Data Exchange (ETDEWEB)

    Pontius, D.H.

    1995-06-01

    The mechanical integrity of ceramic filter elements is a key issue for hot gas cleanup systems. To meet the demands of the advanced power systems, the filter components must sustain the thermal stresses of normal operations (pulse cleaning), of start-up and shut-down conditions, and of unanticipated process upsets such as excessive ash accumulation without catastrophic failure. They must also survive the various mechanical loads associated with handling and assembly, normal operation, and process upsets. For near-term filter systems, these elements must survive at operating temperatures of 1650{degrees}F for three years.

  11. Doppler Compensation by using of Segmented Match Filter

    OpenAIRE

    2008-01-01

    Match filter is one of the important parts of radar receiver. By using of Match Filter, the signal to noise ratio can be maximized so that the probability of detection is increased. Match Filter can be used as a pulse compression filter in radar receiver. Binary phase code is one of the pulse compression methods that, the compression can be down with a Match Filter in the receiver. Doppler effect is one of the problems that degrade the performance of Match Filter. In this paper, two methods “...

  12. Frontal tDCS modulates orbitofrontal reality filtering.

    Science.gov (United States)

    Manuel, A L; David, A W; Bikson, M; Schnider, A

    2014-04-18

    Orbitofrontal reality filtering denotes a memory control mechanism necessary to keep thought and behavior in phase with reality. Its failure induces reality confusion as evident in confabulation and disorientation. In the present study, we explored the influence of orbitofrontal transcranial direct current stimulation (tDCS) on reality filtering. Twenty healthy human subjects made a reality filtering task, while receiving cathodal, anodal, or sham stimulation over the frontal pole in three sessions separated by at least 1week. Computational models predicted that this montage can produce polarity-specific current flow across the posterior medial orbitofrontal cortex (OFC). In agreement with our hypothesis, we found that cathodal tDCS over the frontal pole specifically impaired reality filtering in comparison to anodal and sham stimulation. This study shows that reality filtering, an orbitofrontal function, can be modulated with tDCS.

  13. Liquid cathode primary batteries

    Science.gov (United States)

    Schlaikjer, Carl R.

    1985-03-01

    Lithium/liquid cathode/carbon primary batteries offer from 3 to 6 times the volumetric energy density of zinc/alkaline manganese cells, improved stability during elevated temperature storage, satisfactory operation at temperatures from -40 to +150 °C, and efficient discharge at moderate rates. he lithium/sulfur dioxide cell is the most efficient system at temperatures below 0 °C. Although chemical reactions leading to electrolyte degradation and lithium corrosion are known, the rates of these reactions are slow. While the normal temperature cell reaction produces lithium dithionite, discharge at 60 °C leads to a reduction in capacity due to side reactions involving sulfur dioxide and discharge intermediates. Lithium/thionyl chloride and lithium/sulfuryl chloride cells have the highest practical gravimetric and volumetric energy densities when compared with aqueous and most other nonaqueous systems. For thionyl chloride, discharge proceeds through a series of intermediates to sulfur, sulfur dioxide and lithium chloride. Catalysis, leading to improved rate capability and capacity, has been achieved. The causes of rapid reactions leading to thermal runaway are thought to be chemical in nature. Lithium/sulfuryl chloride cells, which produce sulfur dioxide and lithium chloride on discharge, experience more extensive anode corrosion. An inorganic cosolvent and suitable salt are capable of alleviating this corrosion. Calcium/oxyhalide cells have been studied because of their promise of increased safety without substantial sacrifice of energy density relative to lithium cells. Anode corrosion, particularly during discharge, has delayed practical development.

  14. Liquid cathode primary batteries

    Energy Technology Data Exchange (ETDEWEB)

    Schlaikjer, C.R.

    1985-01-15

    Lithium/liquid cathode/carbon primary batteries offer from 3 to 6 times the volumetric energy density of zinc/alkaline manganese cells, improved stability during elevated temperature storage, satisfactory operation at temperatures from -40 to +150/sup 0/C, and efficient discharge at moderate rates. The lithium/sulfur dioxide cell is the most efficient system at temperatures below 0/sup 0/C. Although chemical reactions leading to electrolyte degradation and lithium corrosion are known, the rates of these reactions are slow. While the normal temperature cell reaction produces lithium dithionite, discharge at 60/sup 0/C leads to a reduction in capacity due to side reactions involving sulfur dioxide and discharge intermediates. Lithium/thionyl chloride and lithium/sulfuryl chloride cells have the highest practical gravimetric and volumetric energy densities when compared with aqueous and most other nonaqueous systems. For thionyl chloride, discharge proceeds through a series of intermediates to sulfur, sulfur dioxide and lithium chloride. Catalysis, leading to improved rate capability and capacity, has been achieved. The causes of rapid reactions leading to thermal runaway are thought to be chemical in nature. Lithium/sulfuryl chloride cells, which produce sulfur dioxide and lithium chloride on discharge, experience more extensive anode corrosion. An inorganic cosolvent and suitable salt are capable of alleviating this corrosion. Calcium/oxyhalide cells have been studied because of their promise of increased safety without substantial sacrifice of energy density relative to lithium cells. Anode corrosion, particularly during discharge, has delayed practical development.

  15. Ultraviolet filters.

    Science.gov (United States)

    Shaath, Nadim A

    2010-04-01

    The chemistry, photostability and mechanism of action of ultraviolet filters are reviewed. The worldwide regulatory status of the 55 approved ultraviolet filters and their optical properties are documented. The photostabilty of butyl methoxydibenzoyl methane (avobenzone) is considered and methods to stabilize it in cosmetic formulations are presented.

  16. a Bombardment Heated Lanthanum-Hexaboride Thermionic Cathode Electron Gun.

    Science.gov (United States)

    Herniter, Marc Efrem

    This dissertation concerns the development and operation of a high current density Pierce-type electron gun with a 0.75-inch-diameter lanthanum hexaboride (LaB _6) thermionic cathode. The objective of this research is to achieve as high a current density as possible from the lanthanum hexaboride cathode. The topics which are addressed are the cathode heating and control system, the Pierce-type electron gun design, and the high voltage pulsing and isolation system. Lanthanum hexaboride is used as a cathode material in applications where high current density and resistance to chemical poisoning are important. Applications include free electron lasers and high power microwave generation. A four stage Marx generator capable of producing 140-kV-peak pulses with a 16 mus decay time constant is used to pulse the electron gun. The cathode is heated to temperatures greater than 1800 ^circ C by electron bombardment from a tungsten filament. Both temperature-limited and space -charge-limited bombardment methods have been investigated. The temperature-limited method is open-loop unstable. Analog and digital control circuits have been developed to control this instability. A simple heating model has been developed and criteria for constructing a controllable system have been established. An instability in the heating system which is caused by evaporation of lanthanum hexaboride from the cathode is discussed. This evaporation reduces the work function of the bombarding filament and makes the temperature -limited bombardment system uncontrollable. The gun has been operated up to voltages of 115 kV achieving beam current densities of 30 A/cm ^2. The electron gun operated dependably up to voltages of 90 kV achieving temperature-limited currents of 50 A. Due to the high fields at the tip of the Pierce -focusing electrode the gun would usually arc at voltages greater than 90 kV. Electron gun operation has been observed in the temperature-limited and space-charge-limited regimes. The

  17. Jet-cleaning experiment and simulation of a pulse-jet cartridge filter%脉冲喷吹滤筒除尘器喷吹清灰实验与数值模拟

    Institute of Scientific and Technical Information of China (English)

    袁彩云; 陈海焱; 李波

    2012-01-01

    通过喷吹实验台对φ147×1 000 mm滤筒的脉冲喷吹清灰过程进行了实验测试,运用数据采集系统得到了滤筒表面压力峰值的动态变化曲线图;并利用CFD模拟滤筒的清灰过程,计算过程采用非稳态计算方法,得到了不同喷吹时刻滤筒表面的压力峰值.在喷吹压力一定的条件下,沿滤筒长度方向上,正压力峰值到达时间是逐渐增加的;滤筒内压力峰值并非随着喷吹时间的增加而不断增大,当喷吹时间大于60 ms时,随着喷吹时间的增加压力峰值有下降趋势.模拟得到的压力峰值曲线与实验曲线变化趋势一致.%By testing the jet-cleaning process of a filter cartridge of 0147 x 1 000 mm in size on a jet experiment platform, obtains a dynamic change curve of peak pressure by means of a data collection system. Adopting CFD to simulate the jet-cleaning process of the filter using an unsteady calculation method, gains the peak pressures at different pulse-jet times. The occurring time of positive peak pressure is gradually increasing along the length direction of the cartridge under a given jet pressure. The increase of the peak pressure in cartridge does not increase with the jet time and the peak pressure has a decrease trend when the jet time is longer than 60 ms. The variation trend of the peak pressure curve from simulation is accordant with the one from the experiment.

  18. Chemical Extraction Preparation of Delithiated Cathode Materials of Li-ion Battery

    Institute of Scientific and Technical Information of China (English)

    YAN Shijian; ZHANG Mingang; CHAI Yuesheng; TIAN Wenhuai

    2009-01-01

    A method of conventional chemical reaction to prepare delithiated cathode materials of Li-ion battery was introduced.The cathode material of Li-ion battery was mixed with oxidizing agent Na_2S_2O_8 in water solution,and the solution was stirred continuously to make the chemical re-action proceed sufficiently,then the reaction product was filtered and finally the insoluble delithiated cathode material was obtained.A series of tests were conducted to verify the composition,crystal structure and electrochemical property of the delithiated cathode materials were all desirable.This method overcomes the shortcomings of battery charging preparation and chemical extraction prepa-ration employing other oxidizing agents.

  19. Hydrogen production in single chamber microbial electrolysis cells with stainless steel fiber felt cathodes

    Science.gov (United States)

    Su, Min; Wei, Liling; Qiu, Zhaozheng; Wang, Gang; Shen, Jianquan

    2016-01-01

    Microbial electrolysis cell (MEC) is a promising technology for sustainable production of hydrogen from biodegradable carbon sources. Employing a low-cost and high efficient cathode to replace platinum catalyzed cathode (Pt/C) for hydrogen generation is a challenge for commercialization of MEC. Here we show that a 3D macroporous stainless steel fiber felt (SSFF) with high electrochemical active surface area has an excellent catalytic activity for hydrogen generation, which is comparable to Pt/C cathode and superior to stainless steel mesh (SSM) cathode in the single-chamber MEC. The SSFF cathode (mean filter rating 100 μm) produces hydrogen at a rate of 3.66 ± 0.43 m3 H2 m-3d-1 (current density of 17.29 ± 1.68 A m-2), with a hydrogen recovery of 76.37 ± 15.04% and overall energy efficiency of 79.61 ± 13.07% at an applied voltage of 0.9 V. The performance of SSFF cathode improves over time due to a decrease in overpotential which caused by corrosion. These results demonstrate that SSFF can be a promising alternative for Pt catalytic cathode in MEC for hydrogen production.

  20. Simultaneous determination of textile dyes by Adsorptive Cathodic Stripping Voltammetry - doi: 10.4025/actascitechnol.v35i2.16595

    National Research Council Canada - National Science Library

    Lidia Brizola Santos; Fernando Santos Domingues; Fernando Rosseto; Vitor de Cinque Almeida; Juliana Carla Garcia; Nilson Evelázio de Souza

    2013-01-01

    The Adsorptive Cathodic Stripping Voltammetry (ACSV - differential pulse) proved to be an efficient method in the separation and quantification of two reactive textile dyes, Procion Yellow (PY) and Procion Red (PR...

  1. Dual Butterfly Match Filter VLSI Design

    Institute of Scientific and Technical Information of China (English)

    LIU Zhenyu; HAN Yueqiu

    2001-01-01

    Match filter is widely used in realtime signal processing, especially in Radar Signal Processing. This paper provides a novel ASIC design,which not only saves resource, but also improves thethroughput of the system. This ASIC is specially designed for Radar Pulse Compression. Certainly it canalso be used in other circumstances, such as FIR filter.

  2. Comparison of filter cleaning performance between VDI and JIS testing rigs for cleanable fabric filter

    OpenAIRE

    Mao, Ning; Yao, Yuping; Hata, Mitsuhiko; Wada, Masashi; Kanaoka, Chikao

    2008-01-01

    VDI type-1 rig and JIS rig are the two major testing rigs for cleanable fabric filters. We measured the filter cleaning performance using these rigs and the results were compared in order to characterize the two testing methods. The filter performance tests showed that the filter cleaning efficiency measured with VDI type-1 rig is higher than that with JIS rig. During pulse jet cleaning, JIS rig gave a higher peak pressure and a shorter time period of pulse jet compared to VDI type-1 rig. A n...

  3. Two-photon photoemission from a copper cathode in an X -band photoinjector

    Science.gov (United States)

    Li, H.; Limborg-Deprey, C.; Adolphsen, C.; McCormick, D.; Dunning, M.; Jobe, K.; Raubenheimer, T.; Vrielink, A.; Vecchione, T.; Wang, F.; Weathersby, S.

    2016-02-01

    This paper presents two-photon photoemission from a copper cathode in an X -band photoinjector. We experimentally verified that the electron bunch charge from photoemission out of a copper cathode scales with laser intensity (I) square for 400 nm wavelength photons. We compare this two-photon photoemission process with the single photon process at 266 nm. Despite the high reflectivity (R ) of the copper surface for 400 nm photons (R =0.48 ) and higher thermal energy of photoelectrons (two-photon at 200 nm) compared to 266 nm photoelectrons, the quantum efficiency of the two-photon photoemission process (400 nm) exceeds the single-photon process (266 nm) when the incident laser intensity is above 300 GW /cm2 . At the same laser pulse energy (E ) and other experimental conditions, emitted charge scales inversely with the laser pulse duration. A thermal emittance of 2.7 mm-mrad per mm root mean square (rms) was measured on our cathode which exceeds by sixty percent larger compared to the theoretical predictions, but this discrepancy is similar to previous experimental thermal emittance on copper cathodes with 266 nm photons. The damage of the cathode surface of our first-generation X -band gun from both rf breakdowns and laser impacts mostly explains this result. Using a 400 nm laser can substantially simplify the photoinjector system, and make it an alternative solution for compact pulsed electron sources.

  4. Influence of the Iron Anisothermal Sintering on the Characteristic of the Hollow Cathode Discharge

    Institute of Scientific and Technical Information of China (English)

    BRUNATTO; Silvio Francisco; MUZART; Joel Louis Rene

    2004-01-01

    This work studies the influence of anisothermal iron sintering process on hollow cathode discharge characteristics. Two independent cathodes form an annular discharge. The pressed cylindrical iron powder sample, acting as central cathode, was placed concentrically in the interior of an external cathode. The external cathode, machined from an AISI 3 l0 steel bar, besides acting to confine the geometry of the plasma, can also acts as a source of alloying elements. The sample heating is a function of the ion bombardment energy and, so, of the discharge electrical parameters: current (or current density) and the effective potential applied to the cathode. Successive anisothermal sintering is performed in a same sample until the reproducibility of the electrical parameters being obtained. The heating experiments up to 1250 ℃, in a gas mixture of 80% Ar + 20% H2, at pressure of 133 Pa, at flow of 2xl0-6 m3s-1, with an inter-cathode radial space of 5.8 mm,were carried out. It was verified the metallurgical evolution of the iron sample sintering process influences the current-ton(time switched-on of the pulse) characteristics of the discharge.

  5. Characteristics of a toroidal planar hollow cathode and its use for the preparation of Bi nanoparticles

    Science.gov (United States)

    Perez, A.; Luna, A. T.; Muhl, S.

    2013-12-01

    Using ideas from the sputter deposition by gas flow hollow cathode (GFHC) we have designed a new version in the form of a toroidal planar hollow cathode. Here the flow of gas is used to entrain the sputtered atoms and nanoparticles formed by agglomeration in the gas phase, through the cathode central exit aperture towards the substrate. We have studied the characteristics of the deposit as a function of the applied pulsed dc electrical power, the argon gas pressure and flow. By varying the different operating parameters, such as pressure (6.7-267 Pa), power (40-120 W) and gas flow (20-140 sccm), it was possible to control the size of the nanoparticles (10-150 nm) and the deposition rate (0.4-4.0 nm min-1). We demonstrate that the nanoparticles are of crystalline bismuth, even though the cathode is made of graphite with small added pieces of bismuth.

  6. When "Optimal Filtering" Isn't

    CERN Document Server

    Fowler, J W; Doriese, W B; Hays-Wehle, J; Joe, Y -I; Morgan, K M; O'Neil, G C; Reintsema, C D; Schmidt, D R; Ullom, J N; Swetz, D S

    2016-01-01

    The so-called "optimal filter" analysis of a microcalorimeter's x-ray pulses is statistically optimal only if all pulses have the same shape, regardless of energy. The shapes of pulses from a nonlinear detector can and do depend on the pulse energy, however. A pulse-fitting procedure that we call "tangent filtering" accounts for the energy dependence of the shape and should therefore achieve superior energy resolution. We take a geometric view of the pulse-fitting problem and give expressions to predict how much the energy resolution stands to benefit from such a procedure. We also demonstrate the method with a case study of K-line fluorescence from several 3d transition metals. The method improves the resolution from 4.9 eV to 4.2 eV at the Cu K$\\alpha$ line (8.0keV).

  7. Research on the effect of cathode plasma expansion on x-band relativistic backward wave oscillator using moving-boundary conformal PIC method

    Science.gov (United States)

    Chen, Zaigao; Wang, Jianguo; Wang, Yue

    2016-09-01

    The cathode plasma expansion has been widely investigated and is recognized as impedance collapse in a relativistic backward wave oscillator (RBWO). However, the process of formation and expansion of cathode plasma is very complicated, and the thickness of plasma is only several millimeters, so the simulation of cathode plasma requires high temporal and spatial resolutions. Only the scaled-down diode model and the thin gas layer model are considered in the previous hybrid simulation, and there are few numerical studies on the effect of cathode plasma expansion on the RBWO. In this paper, the moving-boundary conformal particle-in-cell method is proposed; the cathode plasma front is treated in this novel method as the actual cathode surface, and the explosive electron emission boundary moves as the expansion of cathode plasma. Moreover, in order to accurately simulate the electromagnetic field near the cathode surface, the conformal finite-difference time-domain method based on the enlarged cell technique is adopted. The numerical simulation indicates that the diode voltage decreases and the beam current increases as cathode plasma expands; when the cathode plasma velocity is 10 cm/μs, the pulse duration of the generated microwave decreases from 30 ns to 10 ns, the working frequency decreases from 9.83 GHz to 9.64 GHz, and the output power decreases 30% in the course of cathode plasma expansion.

  8. Food Filter

    Institute of Scientific and Technical Information of China (English)

    履之

    1995-01-01

    A typical food-processing plant produces about 500,000 gallons of waste water daily. Laden with organic compounds, this water usually is evaporated or discharged into sewers.A better solution is to filter the water through

  9. Excimer Emission from Direct Current Microhollow Cathode Discharges

    Science.gov (United States)

    Stark, R. H.; El-Habachi, A.; Shi, W.; Schoenbach, K. H.

    1997-10-01

    Reducing the dimensions of the cathode hole to less than 200 micrometer has allowed us to operate argon discharges in a hollow cathode discharge mode, dc, up to pressures of one atmosphere. Spectral measurements in the VUV have shown that the microdischarges are strong sources of argon excimer radiation at 128 nm. This points to a nonthermal electron energy distribution where a considerable part of the electrons have energies exceeding the ionization potential of argon. Whereas the discharges in argon were dc up to atmospheric pressure, discharges in xenon became unstable at pressures exceeding 300 Torr, and current spikes were observed. The xenon excimer emission at 172 nm, however, was found to increase, independent of the mode, dc or pulsed, when the pressure was increased to one atmosphere. The microdischarges have resistive current-voltage characteristics. This has allowed us to generate simple arrays of these discharges, with possible applications as flat panel excimer lamps.

  10. Pulse Compression Technique of Radio Fuze

    Institute of Scientific and Technical Information of China (English)

    HU Xiu-juan; DENG Jia-hao; SANG Hui-ping

    2006-01-01

    The advantages of using phase-coded pulse compression technique for radio fuze systems are evaluated. With building mathematical models a matched filter has be en implemented successfully. Various simulations for pulse compression waveform coding were done to evaluate the performance of fuze system under noisy environment. The results of the simulation and the data analysis show that the phase-coded pulse compression gets a good result in the signal identification of the radio fuze with matched filter. Simultaneously, a suitable sidelobe suppression filter is established by simulation, the suppressed sidelobe level is acceptable to radio fuze application.

  11. Reservoir Cathode for Electric Space Propulsion Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose a reservoir cathode to improve performance in both ion and Hall-effect thrusters. We propose to adapt our existing reservoir cathode technology to this...

  12. Reservoir Cathode for Electric Space Propulsion Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose a hollow reservoir cathode to improve performance in ion and Hall thrusters. We will adapt our existing reservoir cathode technology to this purpose....

  13. High-current-density, high brightness cathodes for free electron laser applications

    Energy Technology Data Exchange (ETDEWEB)

    Green, M.C. (Varian Associates, Palo Alto, CA (USA). Palo Alto Microwave Tube Div.)

    1987-06-01

    This report discusses the following topics: brightness and emittance of electron beams and cathodes; general requirements for cathodes in high brightness electron guns; candidate cathode types; plasma and field emission cathodes; true field emission cathodes; oxide cathodes; lanthanum hexaborides cathodes; laser driven thermionic cathodes; laser driven photocathodes; impregnated porous tungsten dispenser cathodes; and choice of best performing cathode types.

  14. Mechanistic Enhancement of SOFC Cathode Durability

    Energy Technology Data Exchange (ETDEWEB)

    Wachsman, Eric [Univ. of Maryland, College Park, MD (United States)

    2016-02-01

    Durability of solid oxide fuel cells (SOFC) under “real world” conditions is an issue for commercial deployment. In particular cathode exposure to moisture, CO2, Cr vapor (from interconnects and BOP), and particulates results in long-term performance degradation issues. Here, we have conducted a multi-faceted fundamental investigation of the effect of these contaminants on cathode performance degradation mechanisms in order to establish cathode composition/structures and operational conditions to enhance cathode durability.

  15. Investigation on the Plasma-Induced Emission Properties of Large Area Carbon Nanotube Array Cathodes with Different Morphologies

    OpenAIRE

    Liu Liang; Liao Qingliang; Qin Zi; Zhang Zheng; Qi Junjie; Zhang Yue; Huang Yunhua

    2011-01-01

    Abstract Large area well-aligned carbon nanotube (CNT) arrays with different morphologies were synthesized by using a chemical vapor deposition. The plasma-induced emission properties of CNT array cathodes with different morphologies were investigated. The ratio of CNT height to CNT-to-CNT distance has considerable effects on their plasma-induced emission properties. As the ratio increases, emission currents of CNT array cathodes decrease due to screening effects. Under the pulse electric fie...

  16. Novel Cathodes Prepared by Impregnation Procedures

    Energy Technology Data Exchange (ETDEWEB)

    Eduardo Paz

    2006-09-30

    (1) We showed that similar results were obtained when using various LSM precursors to produce LSM-YSZ cathodes. (2) We showed that enhanced performance could be achieved by adding LSCo to LSMYSZ cathodes. (3) We have preliminary results showing that there is a slow deactivation with LSFYSZ cathodes.

  17. Deconvolution of ultrafast kinetic data with inverse filtering

    Energy Technology Data Exchange (ETDEWEB)

    Banyasz, Akos [Department of Physical Chemistry, Eoetvoes University, P.O. Box 32, H-1518 Budapest 112 (Hungary); Research Institute for Solid State Physics and Optics, Hungarian Academy of Sciences, P.O. Box 49, H-1525 Budapest (Hungary); Matyus, Edit [Department of Physical Chemistry, Eoetvoes University, P.O. Box 32, H-1518 Budapest 112 (Hungary); Keszei, Erno [Department of Physical Chemistry, Eoetvoes University, P.O. Box 32, H-1518 Budapest 112 (Hungary)]. E-mail: keszei@chem.elte.hu

    2005-02-01

    Due to limitations of pulse widths in ultrafast laser or electron pulse kinetic measurements, in the case of subpicosecond characteristic times of the studied reactions, deconvolution with the pulses always distorts the kinetic signal. Here, we describe inverse filtering based on Fourier transformations to deconvolve measured ultrafast kinetic data without evoking a particular kinetic mechanism. Deconvolution methods using additional Wiener filtering or two-parameter regularization are found to give reliable results for simulated as well as experimental data.

  18. Signal propagation in straw tubes with resistive cathode

    CERN Document Server

    Marzec, J; Pawlowski, Z; Konarzewski, B

    2000-01-01

    The analysis presented in this paper is part of the research performed by the authors for the COMPASS experiment at CERN. We have developed a theoretical model of the signal transmission in a straw tube. In contrast to commonly used simplified models, our approach takes into account the energy losses in the cathode resistance. This model allows determination of the main electrical parameters, such as characteristic impedance and signal attenuation, as well as a detailed simulation of the pulse shape dependent on the point of the charge injection. Simulation results have been compared with the results of experimental measurements of different types of the straw detectors. (7 refs).

  19. Electrochemical reduction and cathodic stripping voltammetric determination of clotrimazole

    Directory of Open Access Journals (Sweden)

    Pereira Francisco C.

    2001-01-01

    Full Text Available The reduction of clotrimazole at a mercury electrode, in phosphate buffer, pH>6, involves a reversible one-electron process. The electrochemical process presents a large contribution from adsorption effects. For the differential pulse polarographic determination the addition of Triton X-100 is recommended. Clotrimazole can be determined by cathodic stripping voltammetry at 50 ng mL-1 level when pre-accumulated for 3 min at an accumulation potential of -0.20 V. The proposed method is applied successfully for the determination of clotrimazole in a commercial formulation.

  20. Generalised Filtering

    Directory of Open Access Journals (Sweden)

    Karl Friston

    2010-01-01

    Full Text Available We describe a Bayesian filtering scheme for nonlinear state-space models in continuous time. This scheme is called Generalised Filtering and furnishes posterior (conditional densities on hidden states and unknown parameters generating observed data. Crucially, the scheme operates online, assimilating data to optimize the conditional density on time-varying states and time-invariant parameters. In contrast to Kalman and Particle smoothing, Generalised Filtering does not require a backwards pass. In contrast to variational schemes, it does not assume conditional independence between the states and parameters. Generalised Filtering optimises the conditional density with respect to a free-energy bound on the model's log-evidence. This optimisation uses the generalised motion of hidden states and parameters, under the prior assumption that the motion of the parameters is small. We describe the scheme, present comparative evaluations with a fixed-form variational version, and conclude with an illustrative application to a nonlinear state-space model of brain imaging time-series.

  1. Notch filter

    Science.gov (United States)

    Shelton, G. B. (Inventor)

    1977-01-01

    A notch filter for the selective attenuation of a narrow band of frequencies out of a larger band was developed. A helical resonator is connected to an input circuit and an output circuit through discrete and equal capacitors, and a resistor is connected between the input and the output circuits.

  2. Lifetime experimental study of graphite cathode for relativistic backward wave oscillator

    Science.gov (United States)

    Wu, Ping; Sun, Jun; Chen, Changhua

    2016-07-01

    Graphite cathodes are widely used due to their good emission properties, especially their long lifetime. Some previous papers have researched their lifetime under certain conditions and uncovered some important phenomena. This paper is dedicated to research the lifetime of the graphite cathode under higher power. In the lifetime test, the voltage and current amplitudes are about 970 kV and 9.7 kA, respectively. The repetition rate is 20 Hz. An X-band relativistic backward wave oscillator is used to generate high power microwave by utilizing the electron beam energy. The experimental results demonstrate that the emission property of the graphite cathode remains quite stable during 105 pulses, despite some slight deteriorations regarding the beam and microwave parameters. The macroscopic morphology change of the cathode blade due to material evaporation is observed by a laser microscope. The mass loss of the graphite cathode is about 60 μg/C. Meanwhile, the observation by a scanning electron microscope uncovers that the original numerous flaky micro-structures are totally replaced by a relatively smooth surface at the mid region of the cathode blade and a large number of new micro-protrusions at the blade edges during the lifetime test.

  3. PULSED CAPILLARY DISCHARGE CHARACTERIZATION FOR SOFT X-RAY MICROSCOPY APPLICATIONS

    OpenAIRE

    VALDIVIA LEIVA; MARIA PIA

    2011-01-01

    The hollow cathode capillary discharge is of great interest as a high brightness, short pulse soft x-ray source. This thesis presents work done in the development, modifications, and subsequent characterization of a compact plasma source comprised of a pulsed capillary discharge exploiting hollow cathode dynamics. The low inductance, low stored energy, source is optimized using optical, electrical, x-ray, and e-beam diagnostics. The effect of parameters on the capillary phys...

  4. A knife-edge array field emission cathode

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Bo [Texas A & M Univ., College Station, TX (United States)

    1994-08-01

    many cathode applications require a new type of cathode that is able to produce short pulsed electron beams at high emission current. Gated field emitter arrays of micrometer size are recognized as candidates to meet this need and have become the research focus of vacuum microelectronics. Existing fabrication methods produce emitters that are limited either in frequency response or in current emission. One reason is that the structure of these emitters are not sufficiently optimized. In this study, the author investigated the factors that affect the performance of field emitters. An optimum emitter structure, the knife-edge field emitter array, was developed from the analysis. Large field enhancement factor, large effective emission area, and small emitter capacitance are the advantages of the structure. The author next explored various options of fabricating the knife-edge emitter structure. He proposed a unique thin film process procedure and developed the fabrication techniques to build the emitters on (110) silicon wafers. Data from the initial cathode tests showed very low onset voltages and Fowler-Nordheim type emission. Emission simulation based on the fabricated emitter structure indicated that the knife-edge emitter arrays have the potential to produce high performance in modulation frequency and current emission. Several fabrication issues that await further development are discussed and possible solutions are suggested.

  5. Preliminary field evaluation of high efficiency steel filters

    Energy Technology Data Exchange (ETDEWEB)

    Bergman, W.; Larsen, G.; Lopez, R. [Lawrence Livermore National Laboratory, CA (United States)] [and others

    1995-02-01

    We have conducted an evaluation of two high efficiency steel filters in the exhaust of an uranium oxide grit blaster at the Y-12 Plant in Oak Ridge Tennessee. The filters were installed in a specially designed filter housing with a reverse air-pulse cleaning system for automatically cleaning the filters in-place. Previous tests conducted on the same filters and housing at LLNL under controlled conditions using Arizona road dust showed good cleanability with reverse air pulses. Two high efficiency steel filters, containing 64 pleated cartridge elements housed in the standard 2` x 2` x 1` HEPA frame, were evaluated in the filter test housing using a 1,000 cfm slip stream containing a high concentration of depleted uranium oxide dust. One filter had the pleated cartridges manufactured to our specifications by the Pall Corporation and the other by Memtec Corporation. Test results showed both filters had a rapid increase in pressure drop with time, and reverse air pulses could not decrease the pressure drop. We suspected moisture accumulation in the filters was the problem since there were heavy rains during the evaluations, and the pressure drop of the Memtec filter decreased dramatically after passing clean, dry air through the filter and after the filter sat idle for one week. Subsequent laboratory tests on a single filter cartridge confirmed that water accumulation in the filter was responsible for the increase in filter pressure drop and the inability to lower the pressure drop by reverse air pulses. No effort was made to identify the source of the water accumulation and correct the problem because the available funds were exhausted.

  6. A New Filtering Algorithm Utilizing Radial Velocity Measurement

    Institute of Scientific and Technical Information of China (English)

    LIU Yan-feng; DU Zi-cheng; PAN Quan

    2005-01-01

    Pulse Doppler radar measurements consist of range, azimuth, elevation and radial velocity. Most of the radar tracking algorithms in engineering only utilize position measurement. The extended Kalman filter with radial velocity measureneut is presented, then a new filtering algorithm utilizing radial velocity measurement is proposed to improve tracking results and the theoretical analysis is also given. Simulation results of the new algorithm, converted measurement Kalman filter, extended Kalman filter are compared. The effectiveness of the new algorithm is verified by simulation results.

  7. Observation of Repetition-Rate Dependent Emission From an Un-Gated Thermionic Cathode Rf Gun

    Energy Technology Data Exchange (ETDEWEB)

    Edelen, J. P.; Sun, Y.; Harris, J.R.; Lewellen, J.W.

    2017-06-02

    Recent work at Fermilab in collaboration with the Advanced Photon Source and members of other national labs, designed an experiment to study the relationship between the RF repetition rate and the average current per RF pulse. While existing models anticipate a direct relationship between these two parameters we observed an inverse relationship. We believe this is a result of damage to the barium coating on the cathode surface caused by a change in back-bombardment power that is unaccounted for in the existing theories. These observations shed new light on the challenges and fundamental limitations associated with scaling an ungated thermionic cathode RF gun to high average current.

  8. OBSERVATION OF REPETITION-RATE DEPENDANT EMISSION FROM AN UN-GATED THERMIONIC CATHODE RF GUN

    Energy Technology Data Exchange (ETDEWEB)

    Edelen, J. P. [Fermilab; Sun, Y. [Argonne; Harris, J. R. [AFRL, NM; Lewellen, J. W. [Los Alamos Natl. Lab.

    2016-09-28

    Recent work at Fermilab in collaboration with the Advanced Photon Source and members of other national labs, designed an experiment to study the relationship between the RF repetition rate and the average current per RF pulse. While existing models anticipate a direct relationship between these two parameters we observed an inverse relationship. We believe this is a result of damage to the barium coating on the cathode surface caused by a change in back-bombardment power that is unaccounted for in the existing theories. These observations shed new light on the challenges and fundamental limitations associated with scaling an ungated thermionic cathode RF gun to high average current machines.

  9. Microhollow cathode discharge excimer lamps

    Science.gov (United States)

    Schoenbach, Karl H.; El-Habachi, Ahmed; Moselhy, Mohamed M.; Shi, Wenhui; Stark, Robert H.

    2000-05-01

    Microhollow cathode discharges are high-pressure, nonequilibrium gas discharges between a hollow cathode and a planar or hollow anode with electrode dimensions in the 100 μm range. The large concentration of high-energy electrons, in combination with the high-gas density favors excimer formation. Excimer emission was observed in xenon and argon, at wavelengths of 128 and 172 nm, respectively, and in argon fluoride and xenon chloride, at 193 and 308 nm. The radiant emittance of the excimer radiation was found to increase monotonically with pressure. However, due to the decrease in source size with pressure, the efficiency (ratio of excimer radiant power to input electrical power), has for xenon and argon fluoride a maximum at ˜400 Torr. The maximum efficiency is between 6% and 9% for xenon, and ˜2% for argon fluoride.

  10. Pulsed plasma electron sourcesa)

    Science.gov (United States)

    Krasik, Ya. E.; Yarmolich, D.; Gleizer, J. Z.; Vekselman, V.; Hadas, Y.; Gurovich, V. Tz.; Felsteiner, J.

    2009-05-01

    There is a continuous interest in research of electron sources which can be used for generation of uniform electron beams produced at E ≤105 V/cm and duration ≤10-5 s. In this review, several types of plasma electron sources will be considered, namely, passive (metal ceramic, velvet and carbon fiber with and without CsI coating, and multicapillary and multislot cathodes) and active (ferroelectric and hollow anodes) plasma sources. The operation of passive sources is governed by the formation of flashover plasma whose parameters depend on the amplitude and rise time of the accelerating electric field. In the case of ferroelectric and hollow-anode plasma sources the plasma parameters are controlled by the driving pulse and discharge current, respectively. Using different time- and space-resolved electrical, optical, spectroscopical, Thomson scattering and x-ray diagnostics, the parameters of the plasma and generated electron beam were characterized.

  11. A Study of New Pulse Auscultation System

    Directory of Open Access Journals (Sweden)

    Ying-Yun Chen

    2015-04-01

    Full Text Available This study presents a new type of pulse auscultation system, which uses a condenser microphone to measure pulse sound waves on the wrist, captures the microphone signal for filtering, amplifies the useful signal and outputs it to an oscilloscope in analog form for waveform display and storage and delivers it to a computer to perform a Fast Fourier Transform (FFT and convert the pulse sound waveform into a heartbeat frequency. Furthermore, it also uses an audio signal amplifier to deliver the pulse sound by speaker. The study observed the principles of Traditional Chinese Medicine’s pulsing techniques, where pulse signals at places called “cun”, “guan” and “chi” of the left hand were measured during lifting (100 g, searching (125 g and pressing (150 g actions. Because the system collects the vibration sound caused by the pulse, the sensor itself is not affected by the applied pressure, unlike current pulse piezoelectric sensing instruments, therefore, under any kind of pulsing pressure, it displays pulse changes and waveforms with the same accuracy. We provide an acquired pulse and waveform signal suitable for Chinese Medicine practitioners’ objective pulse diagnosis, thus providing a scientific basis for this Traditional Chinese Medicine practice. This study also presents a novel circuit design using an active filtering method. An operational amplifier with its differential features eliminates the interference from external signals, including the instant high-frequency noise. In addition, the system has the advantages of simple circuitry, cheap cost and high precision.

  12. Optimal pseudorandom pulse position modulation ladar waveforms.

    Science.gov (United States)

    Fluckiger, David U; Boland, Brian F; Marcus, Eran

    2015-03-20

    An algorithm for generating optimal pseudorandom pulse position modulation (PRPPM) waveforms for ladar ranging is presented. Bistatic ladar systems using Geiger-mode avalanche photodiodes require detection of several pulses in order to generate sufficient target statistics to satisfy some detection decision rule. For targets with large initial range uncertainty, it becomes convenient to transmit a pulse train with large ambiguity range. One solution is to employ a PRPPM waveform. An optimal PRPPM waveform will have minimal sidelobes: equivalent to 1 or 0 counts after the pulse correlation filter (compression). This can be accomplished by generating PRPPM pulse trains with optimal or minimal sidelobe autocorrelation.

  13. Reflective article having a sacrificial cathodic layer

    Energy Technology Data Exchange (ETDEWEB)

    Kabagambe, Benjamin; Buchanan, Michael J.; Scott, Matthew S.; Rearick, Brian K.; Medwick, Paul A.; McCamy, James W.

    2017-09-12

    The present invention relates to reflective articles, such as solar mirrors, that include a sacrificial cathodic layer. The reflective article, more particularly includes a substrate, such as glass, having a multi-layered coating thereon that includes a lead-free sacrificial cathodic layer. The sacrificial cathodic layer includes at least one transition metal, such as a particulate transition metal, which can be in the form of flakes (e.g., zinc flakes). The sacrificial cathodic layer can include an inorganic matrix formed from one or more organo-titanates. Alternatively, the sacrificial cathodic layer can include an organic polymer matrix (e.g., a crosslinked organic polymer matrix formed from an organic polymer and an aminoplast crosslinking agent). The reflective article also includes an outer organic polymer coating, that can be electrodeposited over the sacrificial cathodic layer.

  14. Nonparametric estimation of ultrasound pulses

    DEFF Research Database (Denmark)

    Jensen, Jørgen Arendt; Leeman, Sidney

    1994-01-01

    An algorithm for nonparametric estimation of 1D ultrasound pulses in echo sequences from human tissues is derived. The technique is a variation of the homomorphic filtering technique using the real cepstrum, and the underlying basis of the method is explained. The algorithm exploits a priori...

  15. Sun powers Libya cathodic-protection system

    Energy Technology Data Exchange (ETDEWEB)

    Currer, G.W.

    1982-03-22

    Well castings and part of the main 300-mile-long, 32-in diameter pipeline from Sarir to Tobruk are cathodically protected by solar power, which prevents galvanic action by applying an electric direct current of appropriate magnitude and polarity to the steel structures. They then act as cathodes and become the recipients of metallic ions. At each cathodic-protection station, the solar-generaor system consists of solar-panel arrays, electronic controls, and batteries.

  16. Preventing Corrosion by Controlling Cathodic Reaction Kinetics

    Science.gov (United States)

    2016-03-25

    Preventing corrosion by controlling cathodic reaction kinetics Progress Report for Period: 1 SEP 2015-31 MAR 2016 John Keith Department of...25 March 2016 Preventing corrosion by controlling cathodic reaction kinetics Annual Summary Report: FY16 PI: John Keith, 412-624-7016,jakeith...dominate the metal’s cathodic behavior. Within an alkaline environment, we expect the following reduction reactions to be catalyzed on the oxide

  17. CRYSTAL FILTER TEST SET

    Science.gov (United States)

    CRYSTAL FILTERS, *HIGH FREQUENCY, *RADIOFREQUENCY FILTERS, AMPLIFIERS, ELECTRIC POTENTIAL, FREQUENCY, IMPEDANCE MATCHING , INSTRUMENTATION, RADIOFREQUENCY, RADIOFREQUENCY AMPLIFIERS, TEST EQUIPMENT, TEST METHODS

  18. Characteristics of Cu implantation into Si by PBII using UBMS cathode

    Institute of Scientific and Technical Information of China (English)

    于伟东; 夏立芳; 孙跃

    2001-01-01

    The implantation of Cu into Si substrate was carried out by plasma-based ion implantation (PBII) using unbalanced magnetron sputtering (UBMS) cathode as the metal plasma source. The different pulse bias (Up) and the distance between the cathode and the samples (ds-t) were chosen to research the characteristics of this method. The results show that the implantation of metal ions can be realized by the metal plasma source of UBMS cathode. The physical process such as the metal ion pure implantation, the gas ion implantation, the recoil implantation of the metal atoms, the deposition of the metal particles and the re-sputtering of the metal film depend on the energy, dose and deposition rate of the ions (Cu+, Ar+). The metal plasma based ion implantation of Cu into Si substrate is favored by selecting higher Up (60  kV) and larger ds-t (200  mm).

  19. Lifetime of hydrogenated composite cathodes in a vacuum arc ion source

    Energy Technology Data Exchange (ETDEWEB)

    Savkin, K. P., E-mail: savkin@opee.hcei.tsc.ru; Frolova, V. P.; Nikolaev, A. G.; Yushkov, G. Yu. [Institute of High Current Electronics SB RAS, Tomsk 634055 (Russian Federation); Oks, E. M. [Institute of High Current Electronics SB RAS, Tomsk 634055 (Russian Federation); Tomsk State University of Control Systems and Radioelectronics, Tomsk 634050 (Russian Federation); Barengolts, S. A. [Prokhorov General Physics Institute RAS, Moscow 119991 (Russian Federation)

    2016-02-15

    The paper reports on a study of the mass-charge state of the plasma produced in a vacuum arc discharge with composite cathodes which were copper-disk coated with a hydrogenated Zr film of thicknesses 9, 22, and 35 μm. The cathodes allow the generation of multicomponent gas and metal ion beams with a hydrogen ion content from several to several tens of percent. Also investigated is the dependence of the H ion fraction in a beam on the Zr film thickness during erosion to the point of disappearance of Zr peaks in mass-charge spectra. The ability of the vacuum arc system to produce H ions is analyzed by analyzing the cathode lifetime as a function of the film thickness and pulse repetition frequency.

  20. The evidence of cathodic micro-discharges during plasma electrolytic oxidation process

    Energy Technology Data Exchange (ETDEWEB)

    Nominé, A., E-mail: alexandre.nomine@univ-lorraine.fr [Institut Jean Lamour, UMR 7198 CNRS, Université de Lorraine, Parc de Saurupt, 54011 Nancy (France); National Institute of Science and Technology “MISiS,” 4, Leninskij Prospekt, Moscow 119049 (Russian Federation); Martin, J.; Noël, C.; Henrion, G.; Belmonte, T. [Institut Jean Lamour, UMR 7198 CNRS, Université de Lorraine, Parc de Saurupt, 54011 Nancy (France); Bardin, I. V.; Kovalev, V. L.; Rakoch, A. G. [National Institute of Science and Technology “MISiS,” 4, Leninskij Prospekt, Moscow 119049 (Russian Federation)

    2014-02-24

    Plasma electrolytic oxidation (PEO) processing of EV31 magnesium alloy has been carried out in fluoride containing electrolyte under bipolar pulse current regime. Unusual PEO cathodic micro-discharges have been observed and investigated. It is shown that the cathodic micro-discharges exhibit a collective intermittent behavior, which is discussed in terms of charge accumulations at the layer/electrolyte and layer/metal interfaces. Optical emission spectroscopy is used to determine the electron density (typ. 10{sup 15} cm{sup −3}) and the electron temperature (typ. 7500 K) while the role of F{sup −} anions on the appearance of cathodic micro-discharges is pointed out.

  1. 2D simulations of short-pulsed dielectric barrier discharge xenon excimer lamp

    Energy Technology Data Exchange (ETDEWEB)

    Bogdanov, E.A.; Kudryavtsev, A.A. [St. Petersburg State University, St. Petersburg (Russian Federation); Arslanbekov, R.R. [CFD Research Corporation, Huntsville (United States)

    2006-07-01

    Self-consistent two-dimensional (2D) simulations of short-pulsed dielectric barrier discharge (DBD) in pure xenon have been performed. It is shown that during short current pulse the traversal inhomogeneity of the plasma parameters can be important only at the end of the current pulse as an edge effect close to the side walls. During the current pulse, the gap voltage drops until the ionization wave reaches the cathode so the current in the cathode sheath is the displacement current. This means that almost all of the absorbed power is deposited into excitation of xenon atoms and not to the ion heating in the cathode sheath as in the traditional glow discharges. This fact is one of the reasons of high efficiency of short-pulsed DBD. The developed model allows one to estimate the temporal position of the plasma-sheath boundary. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  2. Digital filters

    CERN Document Server

    Hamming, Richard W

    1997-01-01

    Digital signals occur in an increasing number of applications: in telephone communications; in radio, television, and stereo sound systems; and in spacecraft transmissions, to name just a few. This introductory text examines digital filtering, the processes of smoothing, predicting, differentiating, integrating, and separating signals, as well as the removal of noise from a signal. The processes bear particular relevance to computer applications, one of the focuses of this book.Readers will find Hamming's analysis accessible and engaging, in recognition of the fact that many people with the s

  3. Ceramic Hot Gas Filter with Integrated Failsafe System

    Energy Technology Data Exchange (ETDEWEB)

    Heidenreich, S.; Haag, W.; Walch, A.; Scheibner, B.; Mai, R.; Leibold, H.; Seifert, H.

    2002-09-18

    In order to integrate a failsafe system and to improve the cleaning intensity a new cleaning method was recently developed, the CPP (coupled pressure pulse) cleaning (Heidenreich et al. 2001). For the CPP method the cleaning system is directly coupled with the filter candles. One feature of this new technique is that the cleaning gas pressure exceeds the system pressure only by 0.05 to 0.1 MPa, whereas in case of conventional jet pulse systems two times the system pressure (at least 0.6 MPa) is standard. The key advantage of the coupled pressure pulse cleaning is that a safety filter for each filter candle can be integrated in the clean gas side of the filter. Thus, a candle failure is not longer a serious problem. The integrated safety filter enables the operation of the filter system also in case a filter candle breaks. This increases the availability of the filter and prevents an unscheduled costly shut-down of the system. In this paper the design of the ceramic filter wit h the failsafe system and the CPP cleaning will be described. The new developed safety filter elements, their pressure drop and their filtration and clogging behavior will be shown. Tests of single system components, of the whole filter system and first experiences of operating this system will be reported.

  4. A centre-triggered magnesium fuelled cathodic arc thruster uses sublimation to deliver a record high specific impulse

    Science.gov (United States)

    Neumann, Patrick R. C.; Bilek, Marcela; McKenzie, David R.

    2016-08-01

    The cathodic arc is a high current, low voltage discharge that operates in vacuum and provides a stream of highly ionised plasma from a solid conducting cathode. The high ion velocities, together with the high ionisation fraction and the quasineutrality of the exhaust stream, make the cathodic arc an attractive plasma source for spacecraft propulsion applications. The specific impulse of the cathodic arc thruster is substantially increased when the emission of neutral species is reduced. Here, we demonstrate a reduction of neutral emission by exploiting sublimation in cathode spots and enhanced ionisation of the plasma in short, high-current pulses. This, combined with the enhanced directionality due to the efficient erosion profiles created by centre-triggering, substantially increases the specific impulse. We present experimentally measured specific impulses and jet power efficiencies for titanium and magnesium fuels. Our Mg fuelled source provides the highest reported specific impulse for a gridless ion thruster and is competitive with all flight rated ion thrusters. We present a model based on cathode sublimation and melting at the cathodic arc spot explaining the outstanding performance of the Mg fuelled source. A further significant advantage of an Mg-fuelled thruster is the abundance of Mg in asteroidal material and in space junk, providing an opportunity for utilising these resources in space.

  5. Cathode materials: A personal perspective

    Energy Technology Data Exchange (ETDEWEB)

    Goodenough, John B. [Texas Materials Institute, University of Texas at Austin, ETC 9.102, 1 University Station, Austin, TX 78712-1063 (United States)

    2007-12-06

    A thermodynamically stable rechargeable battery has a voltage limited by the window of the electrolyte. An aqueous electrolyte has a window of 1.2 eV, which prevents achieving the high energy density desired for many applications. A non-aqueous electrolyte with a window of 5 eV requires Li{sup +} rather than H{sup +} as the working ion. Early experiments with Li{sub x}TiS{sub 2} cathodes showed competitive capacity and rate capability, but problems with a lithium anode made the voltage of a safe cell based on a sulfide cathode too low to be competitive with a nickel/metal-hydride battery. Transition-metal oxides can give voltages of 4.5 V versus Li{sup +}/Li{sup 0}. However, the challenge with oxides has been to obtain a competitive capacity and rate capability while retaining a high voltage with low-cost, environmentally friendly cathode materials. Comparisons will be made between layered Li{sub 1-x}MO{sub 2}, spinels Li{sub 1-x}[M{sub 2}]O{sub 4}, and olivines Li{sub 1-x}MPO{sub 4} having 0 < x < 1. Although higher capacities can be obtained with layered Li{sub 1-x}MO{sub 2} compounds, which have enabled the wireless revolution, their metastability makes them unlikely to be used in power applications. The spinel and olivine framework structures have been shown to be capable of charge/discharge rates of over 10C with a suitable temperature range for plug-in hybrid vehicles. (author)

  6. Spectral Analysis using Linearly Chirped Gaussian Pulse Stacking

    Institute of Scientific and Technical Information of China (English)

    ZHENG Huan; WANG An-Ting; XU Li-Xin; MING Hai

    2009-01-01

    We analyze the spectrum of a stacked pulse with the technique of linearly chirped Gaussian pulse stacking.Our results show that there are modulation structures in the spectrum of the stacked pulse. The modulation frequencies are discussed in detail. By applying spectral analysis, we find that the intensity fluctuation cannot be smoothed by introducing an optical amplitude filter.

  7. Sono-cathodic stripping voltammetry of manganese at a polished boron-doped diamond electrode: application to the determination of manganese in instant tea.

    Science.gov (United States)

    Saterlay, A J; Foord, J S; Compton, R G

    1999-12-01

    Ultrasonically assisted cathodic stripping voltammetry at a boron-doped diamond electrode was developed for the detection of manganese. Differential-pulse voltammetry was used to give the analytical signal from a cathodic strip of electrodeposited MnO2; linearity was observed from 10(-11) M to at least 3 x 10(-7) M, with 10(-11) M being the detection limit for a 2 min deposition. The procedure involves both ultrasonic-anodic deposition of MnO2 and ultrasonic-cathodic stripping. This novel analytical tool is robust, reproducible, mercury free, oxygen insensitive and highly specific towards manganese. The differential-pulse sono-cathodic stripping voltammetric technique was used to determine successfully the manganese content of two instant tea samples, giving excellent agreement with independent AAS analyses.

  8. Repetitive operation of an L-band magnetically insulated transmission line oscillator with metal array cathode

    Science.gov (United States)

    Qin, Fen; Wang, Dong; Xu, Sha; Zhang, Yong; Fan, Zhi-kai

    2016-04-01

    We present the repetitive operation research results of an L-band magnetically insulated transmission line oscillator with metal array cathode (MAC-MILO) in this paper. To ensure a more uniform emission of electrons emitted from the cathode, metal plates with different outer radii and thicknesses are periodically arranged in longitudinal direction on the cathode substrate to act as emitters. The higher order mode depressed MILO (HDMILO) structure is applied to ensure stability of the tube. Comparison experiments are carried out between velvet cathode and MAC MILO driven by a 20 GW/40 Ω/40 ns/20 Hz pulse power system. Experimental results reveal that the MAC has much lower outgassing rate, much longer life time, and higher repetitive stability. The MAC-MILO could work stably with a rep-rate up to 20 Hz at a power level of 550 MW when employing a 350 kV/35 kA electric pulse. The TE11 mode radiation pattern in the farfield region reveals the tube works steadily on the dominant mode. More than 2000 shots have been tested in repetitive mode without any obvious degradation of the detected microwave parameters.

  9. High-current-density gun with a LaB6 cathode

    Science.gov (United States)

    Ebihara, K.; Hiramatsu, S.

    1996-08-01

    To develop a high-current electron gun for an induction linac, a prototype of a Pierce-type electron gun using planar 12-mm-diam lanthanum hexaboride (LaB6) is studied as a thermionic emitter at high current densities. The cathode is heated up to temperatures of 1750 °C by electron bombardment and thermal radiation from a tungsten heater. The heater that has the highest temperature in the gun is thermally isolated from the outer vacuum chamber with heat shields. The bombardment voltage of ˜1 kV is typically applied to a gap between the cathode and the heater. The gun has been operated up to voltages of 55 kV, obtaining a maximum current density of 20 A/cm2 with a pulse width of 250 ns at a cathode temperature of 1600 °C. High-voltage pulsing results show that the gun, with applied voltages of over 40 kV, is operated in space-charge-limited region at temperatures of over 1600 °C; also it is operated in a temperature-limited region at temperatures of less than 1500 °C. An effective work function of 2.68 eV is obtained. The cathode, when heated up to 1600 °C, emits over 7 A of electrons with a ˜20% reduction after 850 h of continuous operation. These measurements were made between vacuum pressures of 10-6 and 10-7 Torr.

  10. The effect of 1,2-dimethoxyethane on the storage and performance of lithium cells with MnO 2 and (CF) n cathodes

    Science.gov (United States)

    Fr açkowiak, E.; Kuksenko, S.

    The characteristics of lithium cells with MnO 2 and (CF) n cathodes were investigated for two different electrolyte compositions, i.e., LiClO 4/PC+DME and LiClO 4/PC. For such lithium cells, the greater loss of long-term storage capacity was found in the case of cells using mixed PC+DME electrolyte. The oxidation process of DME by the cathode elements during the storage period is assumed to be the cause of the capacity loss. In the case of cells using MnO 2 as a cathode, the polymerisation process of the oxidation products of DME on the cathode surface can be also considered. After storage at 45°C, the smaller loss of capacity was found for the cells using MnO 2 as a cathode. The different behaviour of these two kinds of cells during a pulse discharge was also confirmed.

  11. Experimental investigation of a capacitive blind hollow cathode discharge with central gas injection

    Science.gov (United States)

    Hoffmann, D.; Müller, M.; Petkow, D.; Herdrich, G.; Lein, S.

    2014-12-01

    The operating parameters and resulting plasma properties of a blind hollow cathode (BHC) discharge have been investigated. The hollow cathode was driven capacitively with a pulsed dc signal of 200 kHz in a power range between 50 and 100 W at an ambient pressure of about 10 Pa. The working gas was argon, which was introduced with a ceramic capillary at different positions of the longitudinal axis of the hollow cathode with flow rates of between 30 and 1000 sccm. The current-voltage characteristics were recorded. The pressure at the end of the BHC was measured with a miniaturized pressure transducer with varying volumetric flow rate and axial position of the capillary in the hollow cathode. To characterize the ignition behaviour of the system, the measured breakdown voltages were compared with phenomenological Paschen curves calculated from the pressure data. Optical emission spectroscopy was used to examine the origins of the light emission, comparing the glow mode and hollow cathode mode in particular. A high-speed camera recorded some plasma processes. A mounting with an indium tin oxide coated glass was used to observe the inner volume of the BHC along the longitudinal axis, while the plasma was operated with different parameters. The optical observations revealed an inhomogeneous plasma condition along the axis.

  12. Micro pulse laser radar

    Science.gov (United States)

    Spinhirne, James D. (Inventor)

    1993-01-01

    An eye safe, compact, solid state lidar for profiling atmospheric cloud and aerosol scattering is disclosed. The transmitter of the micro pulse lidar is a diode pumped micro-J pulse energy, high repetition rate Nd:YLF laser. Eye safety is obtained through beam expansion. The receiver employs a photon counting solid state Geiger mode avalanche photodiode detector. Data acquisition is by a single card multichannel scaler. Daytime background induced quantum noise is controlled by a narrow receiver field-of-view and a narrow bandwidth temperature controlled interference filter. Dynamic range of the signal is limited to optical geometric signal compression. Signal simulations and initial atmospheric measurements indicate that micropulse lider systems are capable of detecting and profiling all significant cloud and aerosol scattering through the troposphere and into the stratosphere. The intended applications are scientific studies and environmental monitoring which require full time, unattended measurements of the cloud and aerosol height structure.

  13. Lifetime Studies of Cs2Te Cathodes at the Phin RF Photoinjector at CERN

    CERN Document Server

    Hessler, C; Divall Csatari, M; Doebert, S; Fedosseev, V

    2012-01-01

    The PHIN photoinjector has been developed to study the feasibility of a photoinjector option for the CLIC (Compact LInear Collider) drive beam as an alternative to the baseline design, using a thermionic gun. The CLIC drive beam requires a high charge of 8.4 nC per bunch in 0.14 ms long trains, with 2 ns bunch spacing and 50 Hz macro pulse repetition rate, which corresponds to a total charge per macro pulse of 0.59 mC. This means unusually high peak and average currents for photoinjectors and is challenging concerning the cathode lifetime. In this paper detailed studies of the lifetime of Cs2Te cathodes, produced by the co-evaporation technique, are presented with respect to bunch charge, train length and vacuum level. Furthermore, the impact of the train length and bunch charge on the vacuum level will be discussed and steps to extend the lifetime will be outlined.

  14. Actively Pumped Optical Filters at 532 nm

    Science.gov (United States)

    Billmers, Richard I.; Gayen, S. K.; Contarino, Vincent M.; Scharpf, William J.; Squicciarini, Martin F.; Allocca, David A.

    1995-01-01

    The operation of two narrow-band optical filters at 532.33 nm is presented. Both of these filters operate on the 4P(sub 1/2) to 8S(sub 1/2) excited-state transition in potassium vapor. One of the filters is based on excited-state Faraday effect, and requires the application of an external axial magnetic field. The peak transmission of this filter is approximately 3.5% with a linewidth of less than 10 GHz. The second filter does not require a magnetic field for its operation, but readily attains peak transmissions of 25-30%. The 4P(sub 1/2) state is excited by a 769.9 nm light pulse which is linearly polarized for the first scheme and circularly polarized for the second.

  15. Optimal filtering in multipulse sequences for nuclear quadrupole resonance detection

    Science.gov (United States)

    Osokin, D. Ya.; Khusnutdinov, R. R.; Mozzhukhin, G. V.; Rameev, B. Z.

    2014-05-01

    The application of the multipulse sequences in nuclear quadrupole resonance (NQR) detection of explosive and narcotic substances has been studied. Various approaches to increase the signal to noise ratio (SNR) of signal detection are considered. We discussed two modifications of the phase-alternated multiple-pulse sequence (PAMS): the 180° pulse sequence with a preparatory pulse and the 90° pulse sequence. The advantages of optimal filtering to detect NQR in the case of the coherent steady-state precession have been analyzed. It has been shown that this technique is effective in filtering high-frequency and low-frequency noise and increasing the reliability of NQR detection. Our analysis also shows the PAMS with 180° pulses is more effective than PSL sequence from point of view of the application of optimal filtering procedure to the steady-state NQR signal.

  16. Vacuum arc on the polycrystalline silica cathode

    Directory of Open Access Journals (Sweden)

    D. V. Duhopel'nikov

    2014-01-01

    Full Text Available Thin films of silica and its compounds are used in modern technology to produce Li-ion batteries, wear-resistant and protective coatings, thin-films insulators, etc. This coating is produced with CVD methods, with magnetron sputtering systems or with electron-beam evaporation. The vacuum arc evaporation method, presently, is not used.The paper demonstrates a possibility for a long-term operation of vacuum arc evaporator with polycrystalline silica-aluminum alloy (90% of silica cathode and with magnetic system to create a variable form of arch-like magnetic field on the cathode surface. It was shown that archlike configuration of magnetic field provides a stable discharge and uniform cathode spots moving with the velocities up to 5 m/s with magnetic fields induction about 10 mT. Thus, there is no local melting of the cathode, and this provides its long-term work without chips, cracks and destruction. Cathodes spots move over the cathode surface leaving t big craters with melted edges on its surface. The craters size was 150-450μm. The cathode spot movement character and the craters on the cathode surface were like the spots movement, when working on the copper or aluminum cathodes. With the magnetic field induction less than 1 mT, the cathode spots movement was the same as that of on the silica mono-crystal without magnetic field. Thus, the discharge volt-ampere characteristics for different values of magnetic fields were obtained. Voltampere characteristics were increasing and were shifted to the higher voltage with increasing magnetic field. The voltage was 18.7-26.5 V for the arc current 30-140 A.So, it was confirmed that vacuum arc evaporation method could be used for effective evaporation of silica and silica-based alloys and for thin films deposition of this materials.

  17. Laser optogalvanic wavelength calibration with a commercial hollow cathode iron - neon discharge lamp

    Science.gov (United States)

    Zhu, Xinming; Nur, Abdullahi H.; Misra, Prabhakar

    1994-01-01

    351 optogalvanic transitions have been observed in the 337 - 598 nm wavelength region using an iron - neon hollow cathode discharge lamp and a pulsed tunable dye laser. 223 of these have been identified as transitions associated with neon energy levels. These optogalvanic transitions have allowed, in conjunction with interference fringes recorded concomitantly with an etalon, the calibration of the dye laser wavelength with 0.3/cm accuracy.

  18. A pulsed electron gun for the Plane Wave Transformer Linac

    CERN Document Server

    Mahadevan, S; Nandedkar, R V

    2003-01-01

    A pulsed diode electron gun delivering 500 mA current at 40 kV is described. The gun geometry is optimized using the Electron Trajectory Program EGUN at higher scaling factors by choosing the closest converging starting surface. The effect of an annular gap between cathode and focusing electrode on beam behaviour is compensated by using a suitable focusing electrode. The estimated perveance is 0.065 mu perv and the normalized emittance is within 5 pi mm mrad. The variation in current density at the cathode has been limited to within 10% across the face of the cathode. Salient features of the pulsed power supply and an insight of its interconnection with the gun are presented. The current measured at the Faraday cup is in agreement with the designed perveance.

  19. Pulsed electron source characterization with the modified three gradient method

    CERN Document Server

    Marghitu, S; Dinca, C; Marghitu, O

    2001-01-01

    Results from the Modified Three Gradient Method (MTGM), applied to a pulsed high intensity electron source, are presented. The MTGM makes possible the non-destructive determination of beam emittance in the space charge presence [1]. We apply the MTGM to an experimental system equipped with a Pierce convergent diode, working in pulse mode, and having a directly heated cathode as electron source. This choice was mainly motivated by the availability of an analytical characterization of this source type [2], as well as the extended use of the Pierce type sources in linear accelerators. The experimental data are processed with a numerical matching program, based on the K-V equation for an axially symmetric configuration [3], to determine the emittance and object cross-over position and diameter. The variation of these parameters is further investigated with respect to both electrical and constructive characteristics of the source: cathode heating current, extraction voltage, and cathode-anode distance.

  20. Ozone formation in pulsed SDBD in a wide pressure range

    Science.gov (United States)

    Starikovskiy, Andrey; Nudnova, Maryia; mipt Team

    2011-10-01

    Ozone concentration in surface anode-directed DBD for wide pressure range (150 - 1300 torr) was experimentally measured. Voltage and pressure effect were investigated. Reduced electric field was measured for anode-directed and cathode-directed SDBD. E/n values in cathode-directed SDBD is higher than in cathode-directed on 50 percent at atmospheric pressure. E/n value increase leads to decrease the rate of oxygen dissociation and Ozone formation at lower pressures. Radiating region thickness of sliding discharge was measured. Typical thickness of radiating zone is 0.4-1.0 mm within pressure range 220-740 torr. It was shown that high-voltage pulsed nanosecond discharge due to high E/n value produces less Ozone with compare to other discharges. Kinetic model was proposed to describe Ozone formation in the pulsed nanosecond SDBD.

  1. Convergent Filter Bases

    OpenAIRE

    Coghetto Roland

    2015-01-01

    We are inspired by the work of Henri Cartan [16], Bourbaki [10] (TG. I Filtres) and Claude Wagschal [34]. We define the base of filter, image filter, convergent filter bases, limit filter and the filter base of tails (fr: filtre des sections).

  2. Convergent Filter Bases

    Directory of Open Access Journals (Sweden)

    Coghetto Roland

    2015-09-01

    Full Text Available We are inspired by the work of Henri Cartan [16], Bourbaki [10] (TG. I Filtres and Claude Wagschal [34]. We define the base of filter, image filter, convergent filter bases, limit filter and the filter base of tails (fr: filtre des sections.

  3. Low-noise pulse conditioner

    Science.gov (United States)

    Bird, D.A.

    1981-06-16

    A low-noise pulse conditioner is provided for driving electronic digital processing circuitry directly from differentially induced input pulses. The circuit uses a unique differential-to-peak detector circuit to generate a dynamic reference signal proportional to the input peak voltage. The input pulses are compared with the reference signal in an input network which operates in full differential mode with only a passive input filter. This reduces the introduction of circuit-induced noise, or jitter, generated in ground referenced input elements normally used in pulse conditioning circuits, especially speed transducer processing circuits. This circuit may be used for conditioning the sensor signal from the Fidler coil in a gas centrifuge for separation of isotopic gaseous mixtures.

  4. High frequency group pulse electrochemical machining

    Institute of Scientific and Technical Information of China (English)

    WU Gaoyang; ZHANG Zhijing; ZHANG Weimin; TANG Xinglun

    2007-01-01

    In the process of machining ultrathin metal structure parts,the signal composition of high frequency group pulse,the influence of frequency to reverse current,and the design of the cathode in high frequency group pulse electrochemical machining (HGPECM) are discussed.The experiments on process were carried out.Results indicate that HGPECM can greatly improve the characteristics of the inter-electrode gap flow field,reduce electrode passivation,and obtain high machining quality.The machining quality is obviously improved by increasing the main pulse frequency.The dimensional accuracy reaches 30-40 pro and the roughness attained is at 0.30-0.35 μm.High frequency group pulse electrochemical machining can be successfully used in machining micro-parts.

  5. Methods and apparatuses using filter banks for multi-carrier spread-spectrum signals

    Science.gov (United States)

    Moradi, Hussein; Farhang, Behrouz; Kutsche, Carl A

    2014-05-20

    A transmitter includes a synthesis filter bank to spread a data symbol to a plurality of frequencies by encoding the data symbol on each frequency, apply a common pulse-shaping filter, and apply gains to the frequencies such that a power level of each frequency is less than a noise level of other communication signals within the spectrum. Each frequency is modulated onto a different evenly spaced subcarrier. A demodulator in a receiver converts a radio frequency input to a spread-spectrum signal in a baseband. A matched filter filters the spread-spectrum signal with a common filter having characteristics matched to the synthesis filter bank in the transmitter by filtering each frequency to generate a sequence of narrow pulses. A carrier recovery unit generates control signals responsive to the sequence of narrow pulses suitable for generating a phase-locked loop between the demodulator, the matched filter, and the carrier recovery unit.

  6. Methods and apparatuses using filter banks for multi-carrier spread spectrum signals

    Energy Technology Data Exchange (ETDEWEB)

    Moradi, Hussein; Farhang, Behrouz; Kutsche, Carl A.

    2016-06-14

    A transmitter includes a synthesis filter bank to spread a data symbol to a plurality of frequencies by encoding the data symbol on each frequency, apply a common pulse-shaping filter, and apply gains to the frequencies such that a power level of each frequency is less than a noise level of other communication signals within the spectrum. Each frequency is modulated onto a different evenly spaced subcarrier. A demodulator in a receiver converts a radio frequency input to a spread-spectrum signal in a baseband. A matched filter filters the spread-spectrum signal with a common filter having characteristics matched to the synthesis filter bank in the transmitter by filtering each frequency to generate a sequence of narrow pulses. A carrier recovery unit generates control signals responsive to the sequence of narrow pulses suitable for generating a phase-locked loop between the demodulator, the matched filter, and the carrier recovery unit.

  7. Methods and apparatuses using filter banks for multi-carrier spread-spectrum signals

    Science.gov (United States)

    Moradi, Hussein; Farhang, Behrouz; Kutsche, Carl A

    2014-10-14

    A transmitter includes a synthesis filter bank to spread a data symbol to a plurality of frequencies by encoding the data symbol on each frequency, apply a common pulse-shaping filter, and apply gains to the frequencies such that a power level of each frequency is less than a noise level of other communication signals within the spectrum. Each frequency is modulated onto a different evenly spaced subcarrier. A demodulator in a receiver converts a radio frequency input to a spread-spectrum signal in a baseband. A matched filter filters the spread-spectrum signal with a common filter having characteristics matched to the synthesis filter bank in the transmitter by filtering each frequency to generate a sequence of narrow pulses. A carrier recovery unit generates control signals responsive to the sequence of narrow pulses suitable for generating a phase-locked loop between the demodulator, the matched filter, and the carrier recovery unit.

  8. Methods and apparatuses using filter banks for multi-carrier spread spectrum signals

    Energy Technology Data Exchange (ETDEWEB)

    Moradi, Hussein; Farhang, Behrouz; Kutsche, Carl A

    2017-01-31

    A transmitter includes a synthesis filter bank to spread a data symbol to a plurality of frequencies by encoding the data symbol on each frequency, apply a common pulse-shaping filter, and apply gains to the frequencies such that a power level of each frequency is less than a noise level of other communication signals within the spectrum. Each frequency is modulated onto a different evenly spaced subcarrier. A demodulator in a receiver converts a radio frequency input to a spread-spectrum signal in a baseband. A matched filter filters the spread-spectrum signal with a common filter having characteristics matched to the synthesis filter bank in the transmitter by filtering each frequency to generate a sequence of narrow pulses. A carrier recovery unit generates control signals responsive to the sequence of narrow pulses suitable for generating a phase-locked loop between the demodulator, the matched filter, and the carrier recovery unit.

  9. Hot gas clean-up with ceramic filter elements

    Energy Technology Data Exchange (ETDEWEB)

    Christ, A.; Gross, R.; Renz, U. [Rheinisch-Westfaelische Technische Hochschule, Aachen (Germany). Lehrstuhl fuer Waermeuebertragung und Klimatechnik

    1998-12-31

    Hot gas cleanup is necessary during the combined cycle combustion of coal, ceramic filters are frequently used for filtration. Pressure and velocity measurements inside the filter elements during pulse cleaning of a single ceramic candle filter element were carried out. The experimental set-up is described and the results for filter element cleaning at {var_theta} = 25,500 and 900{degree}C and cleaning pressures of P{sub B} = 1.4, 1.9 and 2.8 bar are presented and discussed. Numerical simulations of filter element cleaning for the experimental conditions are presented and discussed as well. Regarding the good agreement of experimental results with numerical predictions it is proven that numerical simulations of the back-pulse cleaning should be employed as design tool for filter cleaning systems. 32 figs., 2 tabs.

  10. Doppler Compensation by using of Segmented Match Filter

    Directory of Open Access Journals (Sweden)

    Nader Ghadimi

    2008-09-01

    Full Text Available Match filter is one of the important parts of radar receiver. By using of Match Filter, the signal to noise ratio can be maximized so that the probability of detection is increased. Match Filter can be used as a pulse compression filter in radar receiver. Binary phase code is one of the pulse compression methods that, the compression can be down with a Match Filter in the receiver. Doppler effect is one of the problems that degrade the performance of Match Filter. In this paper, two methods “Mixer Array” and “Segmented Match Filter” are proposed for Doppler compensation. The operation of these two methods as Doppler compensation techniques are considered theoretically. The simulation is used to demonstrate the Doppler compensation performance of new techniques compared to conventional methods.

  11. Analysis of cathode geometry to minimize cathode erosion in direct current microplasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Causa, Federica [Dipartimento di Scienze dell' Ambiente, della Sicurezza, del Territorio, degli Alimenti e della Salute, Universita degli studi di Messina, 98122 Messina (Italy); Ghezzi, Francesco; Caniello, Roberto; Grosso, Giovanni [Istituto di Fisica del Plasma, Consiglio Nazionale delle Ricerche, EURATOM-ENEA-CNR Association, Via R. Cozzi 53, 20125 Milano (Italy); Dellasega, David [Istituto di Fisica del Plasma, Consiglio Nazionale delle Ricerche, EURATOM-ENEA-CNR Association, Via R. Cozzi 53, 20125 Milano (Italy); Dipartimento di Energia, Politecnico di Milano, Via Ponzio 34/3, 20133 Milano (Italy)

    2012-12-15

    Microplasma jets are now widely used for deposition, etching, and materials processing. The present study focuses on the investigation of the influence of cathode geometry on deposition quality, for microplasma jet deposition systems in low vacuum. The interest here is understanding the influence of hydrogen on sputtering and/or evaporation of the electrodes. Samples obtained with two cathode geometries with tapered and rectangular cross-sections have been investigated experimentally by scanning electron microscopy and energy dispersion X-ray spectroscopy. Samples obtained with a tapered-geometry cathode present heavy contamination, demonstrating cathode erosion, while samples obtained with a rectangular-cross-section cathode are free from contamination. These experimental characteristics were explained by modelling results showing a larger radial component of the electric field at the cathode inner wall of the tapered cathode. As a result, ion acceleration is larger, explaining the observed cathode erosion in this case. Results from the present investigation also show that the ratio of radial to axial field components is larger for the rectangular geometry case, thus, qualitatively explaining the presence of micro-hollow cathode discharge over a wide range of currents observed in this case. In the light of the above findings, the rectangular cathode geometry is considered to be more effective to achieve cleaner deposition.

  12. Weighted Integrate-And-Dump Filter

    Science.gov (United States)

    Sadr, Ramin

    1989-01-01

    Digital weighted integrate-and-dump filter (WIDF) proposed for detection of weak rectangular-pulse signals corrupted by additive white Gaussian noise. Received signal first low-pass prefiltered, and samples taken at multiple of symbol frequency. Improved performance means lower sampling and processing rates used for given symbol rate, reducing cost of system.

  13. Powerful 170-attosecond XUV pulses generated with few-cycle laser pulses and broadband multilayer optics

    Energy Technology Data Exchange (ETDEWEB)

    Schultze, M [Max-Planck-Institut fuer Quantenoptik, Hans-Kopfermannstrasse 1, D-85748 Garching (Germany); Goulielmakis, E [Max-Planck-Institut fuer Quantenoptik, Hans-Kopfermannstrasse 1, D-85748 Garching (Germany); Uiberacker, M [Department fuer Physik, Ludwig-Maximilians-Universitaet, Am Coulombwall 1, D-85748 Garching (Germany); Hofstetter, M [Department fuer Physik, Ludwig-Maximilians-Universitaet, Am Coulombwall 1, D-85748 Garching (Germany); Kim, J [Laser Science Laboratory, Department of Physics, POSTECH, Pohang, Kyungbuk 790-784 (Korea, Republic of); Kim, D [Laser Science Laboratory, Department of Physics, POSTECH, Pohang, Kyungbuk 790-784 (Korea, Republic of); Krausz, F [Max-Planck-Institut fuer Quantenoptik, Hans-Kopfermannstrasse 1, D-85748 Garching (Germany); Kleineberg, U [Department fuer Physik, Ludwig-Maximilians-Universitaet, Am Coulombwall 1, D-85748 Garching (Germany)

    2007-07-15

    Single 170-as extreme ultraviolet (XUV) pulses delivering more than 10{sup 6} photons/pulse at {approx}100 eV at a repetition rate of 3 kHz are produced by ionizing neon with waveform-controlled sub-5 fs near-infrared (NIR) laser pulses and spectrally filtering the emerging near-cutoff high-harmonic continuum with a broadband, chirped multilayer molybdenum-silicon (Mo/Si) mirror.

  14. Hall-effect thruster--Cathode coupling: The effect of cathode position and magnetic field topology

    Science.gov (United States)

    Sommerville, Jason D.

    2009-12-01

    Hall-effect thruster (HET) cathodes are responsible for the generation of the free electrons necessary to initiate and sustain the main plasma discharge and to neutralize the ion beam. The position of the cathode relative to the thruster strongly affects the efficiency of thrust generation. However, the mechanisms by which the position affects the efficiency are not well understood. This dissertation explores the effect of cathode position on HET efficiency. Magnetic field topology is shown to play an important role in the coupling between the cathode plasma and the main discharge plasma. The position of the cathode within the magnetic field affects the ion beam and the plasma properties of the near-field plume, which explains the changes in efficiency of the thruster. Several experiments were conducted which explored the changes of efficiency arising from changes in cathode coupling. In each experiment, the thrust, discharge current, and cathode coupling voltage were monitored while changes in the independent variables of cathode position, cathode mass flow and magnetic field topology were made. From the telemetry data, the efficiency of the HET thrust generation was calculated. Furthermore, several ion beam and plasma properties were measured including ion energy distribution, beam current density profile, near-field plasma potential, electron temperature, and electron density. The ion beam data show how the independent variables affected the quality of ion beam and therefore the efficiency of thrust generation. The measurements of near-field plasma properties partially explain how the changes in ion beam quality arise. The results of the experiments show that cathode position, mass flow, and field topology affect several aspects of the HET operation, especially beam divergence and voltage utilization efficiencies. Furthermore, the experiments show that magnetic field topology is important in the cathode coupling process. In particular, the magnetic field

  15. Cathodic Protection of Pipeline Using Distributed Control System

    Directory of Open Access Journals (Sweden)

    Gopalakrishnan Jayapalan

    2014-01-01

    Full Text Available Distributed control system (DCS is available in most of the compressor stations of cross-country pipeline systems. Programmable logic controller (PLC is used in all the intermediate pigging (IP stations/sectional valve (SV stations to collect the field data and to control the remote actuated valves. This paper presents how DCS or PLC can be used for cathodic protection of gas pipelines. Virtual instrumentation (VI software is used here for simulation and real-time implementation purpose. Analog input channels available in DCS/PLC can be used to measure pipe to soil potential (PSP with the help of half-cell and voltage transducer. Logic blocks available in DCS can be used as low selector switch to select the lowest PSP. Proportional-integral (PI controller available in DCS/PLC can be used for taking the controlling action. PI controller output varies the firing angle of AC phase controller. Phase controller output is rectified, filtered, and fed to the pipeline as cathodic protection current. Proposed scheme utilizes existing infrastructure to control pipeline corrosion.

  16. Design and Analysis of Robust Active Damping for LCL Filters using Digital Notch Filters

    DEFF Research Database (Denmark)

    Yao, Wenli; Yang, Yongheng; Zhang, Xiaobin;

    2017-01-01

    Resonant poles of LCL filters may challenge the entire system stability especially in digital-controlled Pulse Width Modulation (PWM) inverters. In order to tackle the resonance issues, many active damping solutions have been reported. For instance, a notch filter can be employed to damp the reso......Resonant poles of LCL filters may challenge the entire system stability especially in digital-controlled Pulse Width Modulation (PWM) inverters. In order to tackle the resonance issues, many active damping solutions have been reported. For instance, a notch filter can be employed to damp...... the resonance, where the notch frequency should be aligned exactly to the resonant frequency of the LCL filter. However, parameter variations of the LCL filter as well as the time delay appearing in digital control systems will induce resonance drifting, and thus break this alignment, possibly deteriorating...... the original damping. In this paper, the effectiveness of the notch filter based active damping is firstly explored, considering the drifts of the resonant frequency. It is revealed that, when the resonant frequency drifts away from its nominal value, the phase lead or lag introduced by the notch filter may...

  17. Alternating Pulse Current in Electrocoagulation for Wastewater Treatment to Prevent the Passivation or Al Electrode

    Institute of Scientific and Technical Information of China (English)

    MAO Xuhui; HONG Song; ZHU Hua; LIN Hui; WEI Lin; GAN Fuxing

    2008-01-01

    A novel current feed style, alternating pulse current, was proposed in electrocoagulation aiming at preventing the passivation of electrode materials. The open circuit potential (OCP) measurements after anodic and cathodic potentiodynamic polarization showed that cathodic polarization could activate Al electrode. The surface of Al electrode after alternating pulse current electrocoagulation was investigated by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS), and the results indicate that passivation of Al is not observed. Furthermore, the simulated wastewater treatment tests show that alternating pulse current electrocoagulation has a visible energy saving effect and is worthy of generalization.

  18. NOVEL MICROWAVE FILTER DESIGN TECHNIQUES.

    Science.gov (United States)

    ELECTROMAGNETIC WAVE FILTERS, MICROWAVE FREQUENCY, PHASE SHIFT CIRCUITS, BANDPASS FILTERS, TUNED CIRCUITS, NETWORKS, IMPEDANCE MATCHING , LOW PASS FILTERS, MULTIPLEXING, MICROWAVE EQUIPMENT, WAVEGUIDE FILTERS, WAVEGUIDE COUPLERS.

  19. Nonlinear Pulse Compression and Reshaping Using Cross-Phase Modulation in a Dispersion-Shifted Fiber

    Institute of Scientific and Technical Information of China (English)

    S.; W.; Chan; K.; K.; Chow; C.; Shu

    2003-01-01

    Nonlinear pulse compression has been demonstrated by cross-phase modulation in a dispersion-shifted fiber. The output is obtained from filtering of the broadened optical spectrum and a pulse width reduction from 61 to 28 ps is achieved.

  20. Batteries: Overview of Battery Cathodes

    Energy Technology Data Exchange (ETDEWEB)

    Doeff, Marca M

    2010-07-12

    The very high theoretical capacity of lithium (3829 mAh/g) provided a compelling rationale from the 1970's onward for development of rechargeable batteries employing the elemental metal as an anode. The realization that some transition metal compounds undergo reductive lithium intercalation reactions reversibly allowed use of these materials as cathodes in these devices, most notably, TiS{sub 2}. Another intercalation compound, LiCoO{sub 2}, was described shortly thereafter but, because it was produced in the discharged state, was not considered to be of interest by battery companies at the time. Due to difficulties with the rechargeability of lithium and related safety concerns, however, alternative anodes were sought. The graphite intercalation compound (GIC) LiC{sub 6} was considered an attractive candidate but the high reactivity with commonly used electrolytic solutions containing organic solvents was recognized as a significant impediment to its use. The development of electrolytes that allowed the formation of a solid electrolyte interface (SEI) on surfaces of the carbon particles was a breakthrough that enabled commercialization of Li-ion batteries. In 1990, Sony announced the first commercial batteries based on a dual Li ion intercalation system. These devices are assembled in the discharged state, so that it is convenient to employ a prelithiated cathode such as LiCoO{sub 2} with the commonly used graphite anode. After charging, the batteries are ready to power devices. The practical realization of high energy density Li-ion batteries revolutionized the portable electronics industry, as evidenced by the widespread market penetration of mobile phones, laptop computers, digital music players, and other lightweight devices since the early 1990s. In 2009, worldwide sales of Li-ion batteries for these applications alone were US$ 7 billion. Furthermore, their performance characteristics (Figure 1) make them attractive for traction applications such as

  1. Batteries: Overview of Battery Cathodes

    Energy Technology Data Exchange (ETDEWEB)

    Doeff, Marca M

    2010-07-12

    The very high theoretical capacity of lithium (3829 mAh/g) provided a compelling rationale from the 1970's onward for development of rechargeable batteries employing the elemental metal as an anode. The realization that some transition metal compounds undergo reductive lithium intercalation reactions reversibly allowed use of these materials as cathodes in these devices, most notably, TiS{sub 2}. Another intercalation compound, LiCoO{sub 2}, was described shortly thereafter but, because it was produced in the discharged state, was not considered to be of interest by battery companies at the time. Due to difficulties with the rechargeability of lithium and related safety concerns, however, alternative anodes were sought. The graphite intercalation compound (GIC) LiC{sub 6} was considered an attractive candidate but the high reactivity with commonly used electrolytic solutions containing organic solvents was recognized as a significant impediment to its use. The development of electrolytes that allowed the formation of a solid electrolyte interface (SEI) on surfaces of the carbon particles was a breakthrough that enabled commercialization of Li-ion batteries. In 1990, Sony announced the first commercial batteries based on a dual Li ion intercalation system. These devices are assembled in the discharged state, so that it is convenient to employ a prelithiated cathode such as LiCoO{sub 2} with the commonly used graphite anode. After charging, the batteries are ready to power devices. The practical realization of high energy density Li-ion batteries revolutionized the portable electronics industry, as evidenced by the widespread market penetration of mobile phones, laptop computers, digital music players, and other lightweight devices since the early 1990s. In 2009, worldwide sales of Li-ion batteries for these applications alone were US$ 7 billion. Furthermore, their performance characteristics (Figure 1) make them attractive for traction applications such as

  2. Miniaturized dielectric waveguide filters

    Science.gov (United States)

    Sandhu, Muhammad Y.; Hunter, Ian C.

    2016-10-01

    Design techniques for a new class of integrated monolithic high-permittivity ceramic waveguide filters are presented. These filters enable a size reduction of 50% compared to air-filled transverse electromagnetic filters with the same unloaded Q-factor. Designs for Chebyshev and asymmetric generalised Chebyshev filter and a diplexer are presented with experimental results for an 1800 MHz Chebyshev filter and a 1700 MHz generalised Chebyshev filter showing excellent agreement with theory.

  3. Electrochemical Impedance Studies of SOFC Cathodes

    DEFF Research Database (Denmark)

    Hjelm, Johan; Søgaard, Martin; Wandel, Marie

    2007-01-01

    impedance of the cathode at intermediate operating temperatures. The perovskite is of the La-Sr-Co-Fe type. The EIS response of symmetrical cells with a thick (similar to 200 mu m) gadolinia doped ceria electrolyte was compared with the impedance contribution of the cathode of a full anode supported cell....... The full cells had a Ni-YSZ anode and anode support, a thin YSZ electrolyte, and a CGO barrier layer. The symmetric and full cell cathode responses were compared at open-circuit voltage. Humidified hydrogen was used as the fuel in the full cell measurements. Differential analysis of the impedance data...

  4. Effects of cathodic voltages on structure and wear resistance of plasma electrolytic oxidation coatings formed on aluminium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Li, Qingbiao [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); School of Science, Lanzhou University of Technology, Lanzhou 730050 (China); Liang, Jun, E-mail: jliang@licp.cas.cn [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Liu, Baixing; Peng, Zhenjun [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Wang, Qing [School of Science, Lanzhou University of Technology, Lanzhou 730050 (China)

    2014-04-01

    Highlights: • The PEO coating growth rate increased with the cathodic voltage increasing. • Higher cathodic voltage resulted in more compact coating structure. • The compact structure led to low surface roughness and high wear resistance. - Abstract: Plasma electrolytic oxidation (PEO) coatings were prepared on aluminium alloy using pulsed bipolar power supply at constant anodic voltage and different cathodic voltages. The samples were prepared to attain the same coating thickness by adjusting the processing time. The scanning electron microscope (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD) and tribometer were employed to investigate the microstructure, element content, phase composition and wear resistance of the coatings respectively. It was found that the coating growth rate enhanced obviously and the coatings exhibited a more compact structure with thicker inner layer and lower surface roughness when the cathodic voltage increased. The coatings were mainly composed of crystalline γ-Al{sub 2}O{sub 3} and amorphous silicate oxides and their relative content changed with the cathodic voltage. The wear resistance of the coatings improved significantly with the increase of cathodic voltage.

  5. Advances in Thermionic Cathode of Tungsten and Molybdenum

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Several kinds of tungsten thermonic cathodes have been introduced. As a promising alternative for thoriated tungsten, rare earth doped molybdenum cathode has been studied. Compared with the traditional thoriated tungsten, La-Mo cathode has higher emission current density at lower temperature, but it has poor emission stability. In order to improve the emission stability, systematical study on the emission mechanism of La-Mo cathode has been carried out. The life of La-Mo cathode has been improved and has achieved 1400 h, which exceeds the minimum life for practical uses (1000 h). As another alternative for thoriated tungsten cathode, Y-Mo cathode has shown better performance. The thermionic emission capability of Y-Mo cathode is between that of La-Mo cathode and Th-W cathode.

  6. Pulse Voltammetry.

    Science.gov (United States)

    Osteryoung, Janet

    1983-01-01

    Discusses the nature of pulse voltammetry, indicating that its widespread use arises from good sensitivity and detection limits and from ease of application and low cost. Provides analytical and mechanistic applications of the procedure. (JN)

  7. High current density cathode for electrorefining in molten electrolyte

    Science.gov (United States)

    Li, Shelly X.

    2010-06-29

    A high current density cathode for electrorefining in a molten electrolyte for the continuous production and collection of loose dendritic or powdery deposits. The high current density cathode eliminates the requirement for mechanical scraping and electrochemical stripping of the deposits from the cathode in an anode/cathode module. The high current density cathode comprises a perforated electrical insulated material coating such that the current density is up to 3 A/cm.sup.2.

  8. Reservoir Scandate Cathode for Electric Propulsion Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to combine two revolutionary cathode technologies into a single device for use in electric space propulsion. This will overcome problems that both...

  9. Dynamics of a relativistic electron beam in a high-current diode with a knife-edge cathode

    Science.gov (United States)

    Babykin, V. M.; Gordeev, A. V.; Golovin, G. T.; Korolev, V. D.; Kopchikov, A. V.; Tulupov, M. V.; Chernenko, A. S.; Shuvaev, V. Iu.

    1991-09-01

    The generation of a 130-kA electron beam with a pulse width of 60 ns is investigated experimentally and analytically. In particular, attention is given to the volt-ampere characteristics of knife-edge cathodes of different geometries, angular scatter dynamics, and beam structure. A study of the relativistic electron beam dynamics shows that diode operation in these experiments can be approximated by a formula allowing for the finite thickness of the knife-edge cathode and for plasma and ion motion in the diode gap.

  10. Filter quality of pleated filter cartridges.

    Science.gov (United States)

    Chen, Chun-Wan; Huang, Sheng-Hsiu; Chiang, Che-Ming; Hsiao, Ta-Chih; Chen, Chih-Chieh

    2008-04-01

    The performance of dust cartridge filters commonly used in dust masks and in room ventilation depends both on the collection efficiency of the filter material and the pressure drop across the filter. Currently, the optimization of filter design is based only on minimizing the pressure drop at a set velocity chosen by the manufacturer. The collection efficiency, an equally important factor, is rarely considered in the optimization process. In this work, a filter quality factor, which combines the collection efficiency and the pressure drop, is used as the optimization criterion for filter evaluation. Most respirator manufacturers pleat the filter to various extents to increase the filtration area in the limit space within the dust cartridge. Six sizes of filter holders were fabricated to hold just one pleat of filter, simulating six different pleat counts, ranging from 0.5 to 3.33 pleats cm(-1). The possible electrostatic charges on the filter were removed by dipping in isopropyl alcohol, and the air velocity is fixed at 100 cm s(-1). Liquid dicotylphthalate particles generated by a constant output atomizer were used as challenge aerosols to minimize particle loading effects. A scanning mobility particle sizer was used to measure the challenge aerosol number concentrations and size distributions upstream and downstream of the pleated filter. The pressure drop across the filter was monitored by using a calibrated pressure transducer. The results showed that the performance of pleated filters depend not only on the size of the particle but also on the pleat count of the pleated filter. Based on filter quality factor, the optimal pleat count (OPC) is always higher than that based on pressure drop by about 0.3-0.5 pleats cm(-1). For example, the OPC is 2.15 pleats cm(-1) from the standpoint of pressure drop, but for the highest filter quality factor, the pleated filter needed to have a pleat count of 2.65 pleats cm(-1) at particle diameter of 122 nm. From the aspect of

  11. Modeling High Pressure Micro Hollow Cathode Discharges

    Science.gov (United States)

    2007-11-02

    cathode discharge excimer lamps , Phys. Plasmas 7, 286 (2000). [3] RH Stark and KH Schoenbach, Direct high pressure glow discharges, J. Appl. Phys...temperature profiles in argon glow discharges, J. Appl. Phys. 88, 2234 (2000) [8] M. Moselhy, W. Shi, R. Stark, A flat glow discharge excimer radiation...MHCD acts as a plasma cathode for a third electrode (anode). Some experimental results in this geometry are available for argon and for air from the

  12. The Study on the Adaptive Filtering Method for Eliminating the Motion Artifact in Pulse Oximetry Measurement%脉搏血氧饱和度检测中自适应滤波消除 运动伪差的方法研究

    Institute of Scientific and Technical Information of China (English)

    张虹; 孙卫新; 金捷

    2001-01-01

    Objective  The method of eliminating the motion artif ac t in the pulse oximetry measurement was studied in order to improve the performa nce character of the pulse oximeter. Methods  The noise paramete r was constructed by using light beat in the pulse oximetry system and the LMS(Lea st Mean Square) adaptive filter was used to eliminate the effect of motion artif act. Results  The algorithm of eliminating the motion artifact i n the pulse oximeter was developed. It can successfully extract the normal Photopl ethysmographic signal from the motion artifact in calculating oxygen saturation. Conclusion  This calculating method is simple and can be proces se d in real time, and its result is reliable. It establishes the fundament for fur ther decreasing the noise of pulse oximeter.%目的 研究脉搏血氧饱和度检测系统中运动伪差的消除方法, 以提高脉搏血氧仪检测性能。方法 通过脉搏血氧仪中的双光束构造噪声 参考信号,利用最小均方自适应滤波法消除运动伪差干扰的影响。结果  建立了脉搏血氧饱和度检测中消除运动伪差的计算方法,可成功地从运动伪差中提取正常光 电容积脉搏波信号作为计算氧饱和度的依据。结论 该计算方法简单,可 用于实时处理,且测量结果可靠,为进一步抑制脉搏血氧仪噪声奠定了基础。

  13. Mechanism for negative corona current pulse in CO sub 2 -SF sub 6 mixtures

    CERN Document Server

    Zahoranova, A; Simor, M; Cernak, M

    2003-01-01

    Current waveforms of first negative corona pulses have been measured in CO sub 2 -SF sub 6 mixtures over a pressure range extending from 6.65 to 50 kPa and various overvoltages. Effects of changing cathode secondary electron emission were studied using a copper cathode coated by CuI and graphite. For a given set of experimental conditions it is concluded that in the mixtures containing up to 30% of SF sub 6 the negative corona pulse is associated with the formation of a cathode-directed streamer-like ionizing wave in the immediate vicinity of the cathode. This is in contrast to the discharge behaviour in air-SF sub 6 and N sub 2 -SF sub 6 mixtures, where in similar conditions the discharge develops according to a multi-avalanche Townsend mechanism. (rapid communication)

  14. Composing morphological filters

    NARCIS (Netherlands)

    H.J.A.M. Heijmans (Henk)

    1995-01-01

    textabstractA morphological filter is an operator on a complete lattice which is increasing and idempotent. Two well-known classes of morphological filters are openings and closings. Furthermore, an interesting class of filters, the alternating sequential filters, is obtained if one composes openin

  15. Composing morphological filters

    NARCIS (Netherlands)

    Heijmans, H.J.A.M.

    1995-01-01

    A morphological filter is an operator on a complete lattice which is increasing and idempotent. Two well-known classes of morphological filters are openings and closings. Furthermore, an interesting class of filters, the alternating sequential filters, is obtained if one composes openings and closi

  16. Passive Power Filters

    CERN Document Server

    Künzi, R

    2015-01-01

    Power converters require passive low-pass filters which are capable of reducing voltage ripples effectively. In contrast to signal filters, the components of power filters must carry large currents or withstand large voltages, respectively. In this paper, three different suitable filter struc tures for d.c./d.c. power converters with inductive load are introduced. The formulas needed to calculate the filter components are derived step by step and practical examples are given. The behaviour of the three discussed filters is compared by means of the examples. P ractical aspects for the realization of power filters are also discussed.

  17. Thermoluminescence measurement technique using millisecond temperature pulses.

    Science.gov (United States)

    Manfred, Michael E; Gabriel, Nicholas T; Yukihara, Eduardo G; Talghader, Joseph J

    2010-06-01

    A measurement technique, pulsed thermoluminescence, is described which uses short thermal pulses to excite trapped carriers leading to radiative recombination. The pulses are obtained using microstructures with approximately 500 micros thermal time constants. The technique has many of the advantages of pulsed optically stimulated luminescence without the need for optical sources and filters to isolate the luminescent signal. Charge carrier traps in alpha-Al(2)O(3):C particles on microheaters were filled using 205 nm light. Temperature pulses of 10 and 50 ms were applied to the heaters and compared with a standard thermoluminescence curve taken at a ramp rate of 5 K s(-1). This produced curves of intensity verses temperature similar to standard thermoluminescence except shifted to higher temperatures. The luminescence of single particles was read multiple times with negligible loss of population. The lower limit of the duration of useful pulses appears to be limited by particle size and thermal contact between the particle and heater.

  18. Binary-phase compression of stretched pulses

    Science.gov (United States)

    Lozovoy, Vadim V.; Nairat, Muath; Dantus, Marcos

    2017-10-01

    Pulse stretching and compression are essential for the energy scale-up of ultrafast lasers. Here, we consider a radical approach using spectral binary phases, containing only two values (0 and π) for stretching and compressing laser pulses. We numerically explore different strategies and present results for pulse compression of factors up to a million back to the transform limit and experimentally obtain results for pulse compression of a factor of one hundred, in close agreement with numerical calculations. Imperfections resulting from binary-phase compression are addressed by considering cross-polarized wave generation filtering, and show that this approach leads to compressed pulses with contrast ratios greater than ten orders of magnitude. This new concept of binary-phase stretching and compression, if implemented in a multi-layer optic, could eliminate the need for traditional pulse stretchers and more importantly expensive compressors.

  19. Evaluation of Core Loss in Magnetic Materials Employed in Utility Grid AC Filters

    DEFF Research Database (Denmark)

    Beres, Remus Narcis; Wang, Xiongfei; Blaabjerg, Frede;

    2016-01-01

    Inductive components play an important role in filtering the switching harmonics related to the pulse width modulation in voltage source converters. Particularly, the filter reactor on the converter side of the filter is subjected to rectangular excitation which may lead to significant losses in ...

  20. Software-defined microwave photonic filter with high reconfigurable resolution

    Science.gov (United States)

    Wei, Wei; Yi, Lilin; Jaouën, Yves; Hu, Weisheng

    2016-01-01

    Microwave photonic filters (MPFs) are of great interest in radio frequency systems since they provide prominent flexibility on microwave signal processing. Although filter reconfigurability and tunability have been demonstrated repeatedly, it is still difficult to control the filter shape with very high precision. Thus the MPF application is basically limited to signal selection. Here we present a polarization-insensitive single-passband arbitrary-shaped MPF with ~GHz bandwidth based on stimulated Brillouin scattering (SBS) in optical fibre. For the first time the filter shape, bandwidth and central frequency can all be precisely defined by software with ~MHz resolution. The unprecedented multi-dimensional filter flexibility offers new possibilities to process microwave signals directly in optical domain with high precision thus enhancing the MPF functionality. Nanosecond pulse shaping by implementing precisely defined filters is demonstrated to prove the filter superiority and practicability. PMID:27759062

  1. Optimally shaped narrowband picosecond pulses for femtosecond stimulated Raman spectroscopy.

    Science.gov (United States)

    Hoffman, David P; Valley, David; Ellis, Scott R; Creelman, Mark; Mathies, Richard A

    2013-09-09

    A comparison between a Fabry-Pérot etalon filter and a conventional grating filter for producing the picosecond (ps) Raman pump pulses for femtosecond stimulated Raman spectroscopy (FSRS) is presented. It is shown that for pulses of equal energy the etalon filter produces Raman signals twice as large as that of the grating filter while suppressing the electronically resonant background signal. The time asymmetric profile of the etalon-generated pulse is shown to be responsible for both of these observations. A theoretical discussion is presented which quantitatively supports this hypothesis. It is concluded that etalons are the ideal method for the generation of narrowband ps pulses for FSRS because of the optical simplicity, efficiency, improved FSRS intensity and reduced backgrounds.

  2. Applications of Pulse-Coupled Neural Networks

    CERN Document Server

    Ma, Yide; Wang, Zhaobin

    2011-01-01

    "Applications of Pulse-Coupled Neural Networks" explores the fields of image processing, including image filtering, image segmentation, image fusion, image coding, image retrieval, and biometric recognition, and the role of pulse-coupled neural networks in these fields. This book is intended for researchers and graduate students in artificial intelligence, pattern recognition, electronic engineering, and computer science. Prof. Yide Ma conducts research on intelligent information processing, biomedical image processing, and embedded system development at the School of Information Sci

  3. Compact Rare Earth Emitter Hollow Cathode

    Science.gov (United States)

    Watkins, Ronald; Goebel, Dan; Hofer, Richard

    2010-01-01

    A compact, high-current, hollow cathode utilizing a lanthanum hexaboride (LaB6) thermionic electron emitter has been developed for use with high-power Hall thrusters and ion thrusters. LaB6 cathodes are being investigated due to their long life, high current capabilities, and less stringent xenon purity and handling requirements compared to conventional barium oxide (BaO) dispenser cathodes. The new cathode features a much smaller diameter than previously developed versions that permit it to be mounted on axis of a Hall thruster ( internally mounted ), as opposed to the conventional side-mount position external to the outer magnetic circuit ("externally mounted"). The cathode has also been reconfigured to be capable of surviving vibrational loads during launch and is designed to solve the significant heater and materials compatibility problems associated with the use of this emitter material. This has been accomplished in a compact design with the capability of high-emission current (10 to 60 A). The compact, high-current design has a keeper diameter that allows the cathode to be mounted on the centerline of a 6- kW Hall thruster, inside the iron core of the inner electromagnetic coil. Although designed for electric propulsion thrusters in spacecraft station- keeping, orbit transfer, and interplanetary applications, the LaB6 cathodes are applicable to the plasma processing industry in applications such as optical coatings and semiconductor processing where reactive gases are used. Where current electrical propulsion thrusters with BaO emitters have limited life and need extremely clean propellant feed systems at a significant cost, these LaB6 cathodes can run on the crudest-grade xenon propellant available without impact. Moreover, in a laboratory environment, LaB6 cathodes reduce testing costs because they do not require extended conditioning periods under hard vacuum. Alternative rare earth emitters, such as cerium hexaboride (CeB6) can be used in this

  4. Optical filters inhibiting television-induced photosensitive seizures.

    Science.gov (United States)

    Takahashi, Y; Sato, T; Goto, K; Fujino, M; Fujiwara, T; Yamaga, M; Ito, T; Isono, H; Kondo, N

    2001-11-27

    Televised images are the most common stimulus for provoking photosensitive seizures in photosensitive persons. To inhibit photosensitive seizures in photosensitive persons who do or do not have epilepsy, the authors sought nonpharmacologic methods for reducing the levels of photic stimulation of televised images. The authors found two types of pathophysiologic mechanisms (wavelength-dependent and quantity of light-dependent mechanisms) for photoparoxysmal responses (PPR). The authors tested two different types of optical filters, one reflecting long-wavelength red light selectively, which stimulates a wavelength-dependent mechanism, and the other absorbing light in the visible spectrum evenly (neutral density filters). Inhibiting effects of optical filters were studied by conventional intermittent photic stimulation (IPS) using strobe light and novel photic stimulation using flashing cathode ray tubes (CRT). Both filters individually inhibited PPR insufficiently (less than 50%). Compound optical filters, composed of both types of filters, can inhibit the PPR, approximately 90% for IPS and 95% for photic stimulation with CRT. These compound optical filters do not destroy chromaticity of emissions from the television's CRT. These compound filters may be useful to prevent seizures induced by television in photosensitive persons.

  5. 12脉冲自耦变压整流器的优化与滤波电感的设计%Optimization of 12-pulse autotransformer rectifier units and design of filter inductor

    Institute of Scientific and Technical Information of China (English)

    蒋磊磊; 陈乾宏; 毛浪

    2012-01-01

    多脉冲整流器作为一种无源整流装置,具有系统可靠性高,结构简单,效率高,过载能力强等特点,广泛应用于航空领域.相关航空标准规定交流用电设备输入电流THD<10%,而12脉冲整流器输入电流THD的理论值为15.2%,不能满足要求.为满足谐波标准,通常在交流侧和直流侧串入电感来降低输入电流的THD,针对P型12脉冲自耦变压整流器,从理论上推导输入电流谐波表达式,为交直流侧电感设计提供依据,同时采用高饱和磁通密度的铁钴钒材料设计磁性元件,减小了系统体积和重量,完成了一台4kW 12脉冲自耦变压器的设计,输入电流THD满足航空标准.%Because of its simple structure, high reliability and strong overload capacity, multi-pulse rectifier is widely used for the electronic facilities applied in the aircraft. Related aviation standards require that the THD of input current of AC electrical equipments must be less than 10% . However, theoretical value of 12-pulse ATRU input current THD is 15. 2% , and it doesn't meet the related aviation standards. To satisfy the standards, AC and DC inductor are added to reduce input current THD so that the original method can meet engineering requirements. In this paper the expression of input current harmonic which provides a theoretical basis for AC and DC inductor is derived. This paper also uses Fe-Co-V alloy which has high saturation flux density to reduce system' s volume and weight. At last, this paper designed a 4kW P-type 12-pulse auto-transformer rectifier whose input current THD satisfies the aviation standards.

  6. Heating dominated inception of pulsed discharges

    Science.gov (United States)

    Agnihotri, Ashutosh; Hundsdorfer, Willem; Ebert, Ute

    2016-09-01

    We simulate the inception of pulsed discharges with heating as the driving agent that leads to spark formation. To understand the phenomenon, we developed a 2D-cylindrically symmetric model that couples the electric discharge dynamics with the background gas dynamics. To capture the ion dynamics well, we reduced the classical drift-diffusion-reaction model of electric discharges to the timescale of ion motion. Additionally, we include secondary emission of electrons from the cathode. We employed the model to study electrical breakdown in air at STP conditions between planar electrodes under the application of pulsed voltages. Our model captures space-charge effects, thermal shocks and induced pressure waves. We observe a cycle of discharge pulses heating the gas and the thermal expansion helping the discharge. This cycle might either lead to spark formation or to discharge decay.

  7. 2013 Estorm - Invited Paper - Cathode Materials Review

    Energy Technology Data Exchange (ETDEWEB)

    Daniel, Claus [ORNL; Mohanty, Debasish [ORNL; Li, Jianlin [ORNL; Wood III, David L [ORNL

    2014-01-01

    The electrochemical potential of cathode materials defines the positive side of the terminal voltage of a battery. Traditionally, cathode materials are the energy-limiting or voltage-limiting electrode. One of the first electrochemical batteries, the voltaic pile invented by Alessandro Volta in 1800 (Phil. Trans. Roy. Soc. 90, 403 431) had a copper-zinc galvanic element with a terminal voltage of 0.76 V. Since then, the research community has increased capacity and voltage for primary (nonrechargeable) batteries and round-trip efficiency for secondary (rechargeable) batteries. Successful secondary batteries have been the lead acid with a lead oxide cathode and a terminal voltage of 2.1 V and later the NiCd with a nickel(III) oxide hydroxide cathode and a 1.2 V terminal voltage. The relatively low voltage of those aqueous systems and the low round-trip efficiency due to activation energies in the conversion reactions limited their use. In 1976, Wittingham (J. Electrochem. Soc., 123, 315) and Besenhard (J Power Sources 1(3), 267) finally enabled highly reversible redox reactions by intercalation of lithium ions instead of by chemical conversion. In 1980, Goodenough and Mizushima (Mater. Res. Bull. 15, 783 789) demonstrated a high-energy and high-power LiCoO2 cathode, allowing for an increase of terminal voltage far beyond 3 V. Over the past four decades, the international research community has further developed cathode materials of many varieties. Current state-of-the-art cathodes demonstrate voltages beyond any known electrolyte stability window, bringing electrolyte research once again to the forefront of battery research.

  8. Improved cathode materials for microbial electrosynthesis

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, T; Nie, HR; Bain, TS; Lu, HY; Cui, MM; Snoeyenbos-West, OL; Franks, AE; Nevin, KP; Russell, TP; Lovley, DR

    2013-01-01

    Microbial electrosynthesis is a promising strategy for the microbial conversion of carbon dioxide to transportation fuels and other organic commodities, but optimization of this process is required for commercialization. Cathodes which enhance electrode-microbe electron transfer might improve rates of product formation. To evaluate this possibility, biofilms of Sporomusa ovata, which are effective in acetate electrosynthesis, were grown on a range of cathode materials and acetate production was monitored over time. Modifications of carbon cloth that resulted in a positive-charge enhanced microbial electrosynthesis. Functionalization with chitosan or cyanuric chloride increased acetate production rates 6-7 fold and modification with 3-aminopropyltriethoxysilane gave rates 3-fold higher than untreated controls. A 3-fold increase in electrosynthesis over untreated carbon cloth cathodes was also achieved with polyaniline cathodes. However, not all strategies to provide positively charged surfaces were successful, as treatment of carbon cloth with melamine or ammonia gas did not stimulate acetate electrosynthesis. Treating carbon cloth with metal, in particular gold, palladium, or nickel nanoparticles, also promoted electrosynthesis, yielding electrosynthesis rates that were 6-,4.7- or 4.5-fold faster than the untreated control, respectively. Cathodes comprised of cotton or polyester fabric treated with carbon nanotubes yielded cathodes that supported acetate electrosynthesis rates that were similar to 3-fold higher than carbon cloth controls. Recovery of electrons consumed in acetate was similar to 80% for all materials. The results demonstrate that one approach to increase rates of carbon dioxide reduction in microbial electrosynthesis is to modify cathode surfaces to improve microbe-electrode interactions.

  9. Multiple cathodic reaction mechanisms in seawater cathodic biofilms operating in sediment microbial fuel cells.

    Science.gov (United States)

    Babauta, Jerome T; Hsu, Lewis; Atci, Erhan; Kagan, Jeff; Chadwick, Bart; Beyenal, Haluk

    2014-10-01

    In this study, multiple reaction mechanisms in cathodes of sediment microbial fuel cells (SMFCs) were characterized by using cyclic voltammetry and microelectrode measurements of dissolved oxygen and pH. The cathodes were acclimated in SMFCs with sediment and seawater from San Diego Bay. Two limiting current regions were observed with onset potentials of approximately +400 mVAg/AgCl for limiting current I and -120 mVAg/AgCl for limiting current II. The appearance of two catalytic waves suggests that multiple cathodic reaction mechanisms influence cathodic performance. Microscale oxygen concentration measurements showed a zero surface concentration at the electrode surface for limiting current II but not for limiting current I, which allowed us to distinguish limiting current II as the conventional oxygen reduction reaction and limiting current I as a currently unidentified cathodic reaction mechanism. Microscale pH measurements further confirmed these results.

  10. Matched filter based iterative adaptive approach

    Science.gov (United States)

    Nepal, Ramesh; Zhang, Yan Rockee; Li, Zhengzheng; Blake, William

    2016-05-01

    Matched Filter sidelobes from diversified LPI waveform design and sensor resolution are two important considerations in radars and active sensors in general. Matched Filter sidelobes can potentially mask weaker targets, and low sensor resolution not only causes a high margin of error but also limits sensing in target-rich environment/ sector. The improvement in those factors, in part, concern with the transmitted waveform and consequently pulse compression techniques. An adaptive pulse compression algorithm is hence desired that can mitigate the aforementioned limitations. A new Matched Filter based Iterative Adaptive Approach, MF-IAA, as an extension to traditional Iterative Adaptive Approach, IAA, has been developed. MF-IAA takes its input as the Matched Filter output. The motivation here is to facilitate implementation of Iterative Adaptive Approach without disrupting the processing chain of traditional Matched Filter. Similar to IAA, MF-IAA is a user parameter free, iterative, weighted least square based spectral identification algorithm. This work focuses on the implementation of MF-IAA. The feasibility of MF-IAA is studied using a realistic airborne radar simulator as well as actual measured airborne radar data. The performance of MF-IAA is measured with different test waveforms, and different Signal-to-Noise (SNR) levels. In addition, Range-Doppler super-resolution using MF-IAA is investigated. Sidelobe reduction as well as super-resolution enhancement is validated. The robustness of MF-IAA with respect to different LPI waveforms and SNR levels is also demonstrated.

  11. Preparation of nanocomposite thoriated tungsten cathode by swaging technique

    Institute of Scientific and Technical Information of China (English)

    王发展; 诸葛飞; 张晖; 丁秉钧

    2002-01-01

    By using the high energy ball milling method,the nanosized ThO2 powders were obtained.Through mixing powders,sintering and hot swaging processing,a nanocomposite thoriated tungsten cathode was fabricated.The relative density of the nanocomposite material is near 100%.The microstructure of nanocomposite cathode is quite different from that of conventional thoriated tungsten cathode.Most of thoria particles are less than 100 nm in diameter,and distribute on the boundaries of tungsten grains.The nanocomposite cathode shows a much lower arc starting field than that of conventional cathode,which will improve the performance of the cathode significantly.

  12. Method of securing filter elements

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Erik P.; Haslam, Jeffery L.; Mitchell, Mark A.

    2016-10-04

    A filter securing system including a filter unit body housing; at least one tubular filter element positioned in the filter unit body housing, the tubular filter element having a closed top and an open bottom; a dimple in either the filter unit body housing or the top of the tubular filter element; and a socket in either the filter unit body housing or the top of the tubular filter element that receives the dimple in either the filter unit body housing or the top of the tubular filter element to secure the tubular filter element to the filter unit body housing.

  13. a Portable Pulsed Neutron Generator

    Science.gov (United States)

    Skoulakis, A.; Androulakis, G. C.; Clark, E. L.; Hassan, S. M.; Lee, P.; Chatzakis, J.; Bakarezos, M.; Dimitriou, V.; Petridis, C.; Papadogiannis, N. A.; Tatarakis, M.

    2014-02-01

    The design and construction of a pulsed plasma focus device to be used as a portable neutron source for material analysis such as explosive detection using gamma spectroscopy is presented. The device is capable of operating at a repetitive rate of a few Hz. When deuterium gas is used, up to 105 neutrons per shot are expected to be produced with a temporal pulse width of a few tens of nanoseconds. The pulsed operation of the device and its portable size are its main advantage in comparison with the existing continuous neutron sources. Parts of the device include the electrical charging unit, the capacitor bank, the spark switch (spark gap), the trigger unit and the vacuum-fuel chamber / anode-cathode. Numerical simulations are used for the simulation of the electrical characteristics of the device including the scaling of the capacitor bank energies with total current, the pinch current, and the scaling of neutron yields with energies and currents. The MCNPX code is used to simulate the moderation of the produced neutrons in a simplified geometry and subsequently, the interaction of thermal neutrons with a test target and the corresponding prompt γ-ray generation.

  14. The influence of cathode excavation of cathodic arc evaporator on thickness uniformity and erosion products angle distribution

    Directory of Open Access Journals (Sweden)

    D. V. Duhopel'nikov

    2014-01-01

    Full Text Available Cathodic arc evaporators are used for coating with functional films. Prolonged or buttend evaporators may be used for this purposes. In butt-end evaporator the cathode spots move continuously on the cathode work surface and evaporate cathode material. High depth excavation profile forms on the cathode work surface while the thick coating precipitation (tens or hundreds of microns. The cathode excavation profile is shaped like a “cup” with high walls for electrostatic discharge stabilization systems with axial magnetic fields. Cathode spots move on the bottom of the “cup”. It is very likely that high “cup” walls are formed as a result of lasting work time influence on the uniformity of precipitated films.In the present work the influence of excavation profile walls height on the uniformity of precipitated coating was carried out. The high profile walls are formed due to lasting work of DC vacuum arc evaporator. The cathode material used for tests was 3003 aluminum alloy. The extended substrate was placed parallel to the cathode work surface. Thickness distribution along the substrate length with the new cathode was obtained after 6 hours and after 12 hours of continuous operation.The thickness distribution of precipitated coating showed that the cathode excavation has an influence on the angular distribution of the matter escaping the cathode. It can be clearly seen from the normalized dependence coating thickness vs the distance from the substrate center. Also the angular distribution of the matter flow from the cathode depending on the cathode working time was obtained. It was shown that matter flow from the cathode differs from the LambertKnudsen law. The more the cathode excavation the more this difference.So, cathode excavation profile has an influence on the uniformity of precipitated coating and it is necessary to take in account the cathode excavation profile while coating the thick films.

  15. Parallel Operation of Microhollow Cathode Discharges

    Science.gov (United States)

    Stark, Robert H.; Shi, Wenhui; Schoenbach, Karl H.

    1998-10-01

    The dc current-voltage characteristics of microhollow cathode discharges has, in certain ranges of the discharge current, a positive slope [1]. In these current ranges it should be possible to operate multiple discharges in parallel without individual ballast, and be used as flat panel excimer lamps [2] or large area plasma cathodes. In order to verify this hypothesis we have studied the parallel operation of two microhollow cathode discharges of 100 micrometer hole diameter in argon at pressures from 100 Torr to 800 Torr. Stable dc operation of the two discharges, without individual ballast, was obtained if the voltage-current characteristics of the individual discharges had a positive slope greater than 10 V/mA over a voltage range of more than 5 to obtain parallel operation over the entire current range of the microhollow cathode discharges, which includes regions of negative differential conductivity, we have replaced the metal anode by a semi-insulating semiconductor, which serves as distributed resistive ballast. With this method, we were able to ignite and sustain an array of dc microhollow cathode discharges over a wide range of pressure and discharge current. [1] K.H.Schoenbach et al. Appl. Phys. Lett. 68, 13 (1996). [2] A.El-Habachi and K.H.Schoenbach, APL. 72, 1 (1998). This work was funded by the Department of Energy, Advanced Energy Division, and by the Air Force Office of Scientific Research (AFOSR) in cooperation with the DDR&E Air Plasma Ramparts MURI Program.

  16. ADVANCED HOT GAS FILTER DEVELOPMENT

    Energy Technology Data Exchange (ETDEWEB)

    E.S. Connolly; G.D. Forsythe

    1998-12-22

    Advanced, coal-based power plants will require durable and reliable hot gas filtration systems to remove particulate contaminants from the gas streams to protect downstream components such as turbine blades from erosion damage. It is expected that the filter elements in these systems will have to be made of ceramic materials to withstand goal service temperatures of 1600 F or higher. Recent demonstration projects and pilot plant tests have indicated that the current generation of ceramic hot gas filters (cross-flow and candle configurations) are failing prematurely. Two of the most promising materials that have been extensively evaluated are clay-bonded silicon carbide and alumina-mullite porous monoliths. These candidates, however, have been found to suffer progressive thermal shock fatigue damage, as a result of rapid cooling/heating cycles. Such temperature changes occur when the hot filters are back-pulsed with cooler gas to clean them, or in process upset conditions, where even larger gas temperature changes may occur quickly and unpredictably. In addition, the clay-bonded silicon carbide materials are susceptible to chemical attack of the glassy binder phase that holds the SiC particles together, resulting in softening, strength loss, creep, and eventual failure.

  17. Micro pulse lidar

    Science.gov (United States)

    Spinhirne, James D.

    1993-01-01

    An eye safe, compact, solid state lidar for profiling atmospheric cloud and aerosol scattering has been demonstrated. The transmitter of the micropulse lidar is a diode pumped micro-J pulse energy, high repetition rate Nd:YLF laser. Eye safety is obtained through beam expansion. The receiver employs a photon counting solid state Geiger mode avalanche photodiode detector. Data acquisition is by a single card multichannel scaler. Daytime background induced quantum noise is controlled by a narrow receiver field-of-view and a narrow bandwidth temperature controlled interference filter. Dynamic range of the signal is limited by optical geometric signal compression. Signal simulations and initial atmospheric measurements indicate that systems built on the micropulse lidar concept are capable of detecting and profiling all significant cloud and aerosol scattering through the troposphere and into the stratosphere. The intended applications are scientific studies and environmental monitoring which require full time, unattended measurements of the cloud and aerosol height structure.

  18. Generalized Hampel Filters

    Science.gov (United States)

    Pearson, Ronald K.; Neuvo, Yrjö; Astola, Jaakko; Gabbouj, Moncef

    2016-12-01

    The standard median filter based on a symmetric moving window has only one tuning parameter: the window width. Despite this limitation, this filter has proven extremely useful and has motivated a number of extensions: weighted median filters, recursive median filters, and various cascade structures. The Hampel filter is a member of the class of decsion filters that replaces the central value in the data window with the median if it lies far enough from the median to be deemed an outlier. This filter depends on both the window width and an additional tuning parameter t, reducing to the median filter when t=0, so it may be regarded as another median filter extension. This paper adopts this view, defining and exploring the class of generalized Hampel filters obtained by applying the median filter extensions listed above: weighted Hampel filters, recursive Hampel filters, and their cascades. An important concept introduced here is that of an implosion sequence, a signal for which generalized Hampel filter performance is independent of the threshold parameter t. These sequences are important because the added flexibility of the generalized Hampel filters offers no practical advantage for implosion sequences. Partial characterization results are presented for these sequences, as are useful relationships between root sequences for generalized Hampel filters and their median-based counterparts. To illustrate the performance of this filter class, two examples are considered: one is simulation-based, providing a basis for quantitative evaluation of signal recovery performance as a function of t, while the other is a sequence of monthly Italian industrial production index values that exhibits glaring outliers.

  19. Experimental investigation of a 1 kA/cm² sheet beam plasma cathode electron gun.

    Science.gov (United States)

    Kumar, Niraj; Pal, Udit Narayan; Pal, Dharmendra Kumar; Prajesh, Rahul; Prakash, Ram

    2015-01-01

    In this paper, a cold cathode based sheet-beam plasma cathode electron gun is reported with achieved sheet-beam current density ∼1 kA/cm(2) from pseudospark based argon plasma for pulse length of ∼200 ns in a single shot experiment. For the qualitative assessment of the sheet-beam, an arrangement of three isolated metallic-sheets is proposed. The actual shape and size of the sheet-electron-beam are obtained through a non-conventional method by proposing a dielectric charging technique and scanning electron microscope based imaging. As distinct from the earlier developed sheet beam sources, the generated sheet-beam has been propagated more than 190 mm distance in a drift space region maintaining sheet structure without assistance of any external magnetic field.

  20. Current self-limitation in a transverse nanosecond discharge with a slotted cathode

    Science.gov (United States)

    N, A. ASHURBEKOV; K, O. IMINOV; O, A. POPOV; G, S. SHAKHSINOV

    2017-03-01

    A high-voltage transverse pulsed nanosecond discharge with a slotted hollow cathode was found to be a source of high-energy (few kV) ribbon electron beams. Conditions for the formation and extinction of electron beams were experimentally studied in discharges in helium at pressures of 1–100 Torr. It was found that interaction of fast electrons with a non-uniform electric field near the slotted cathode led to limitation of the magnitude of the discharge current. A physical model was developed to describe the discharge current self-limitation that was in satisfactory agreement with the experimental results. Some technical solutions that are expected to increase the upper current limits in transverse nanosecond discharge are discussed.

  1. Adsorptive Cathodic Stripping Voltammetric Determination of Cefoperazone in Bulk Powder, Pharmaceutical Dosage Forms, and Human Urine

    Science.gov (United States)

    Hoang, Vu Dang; Huyen, Dao Thi; Phuc, Phan Hong

    2013-01-01

    The electroreduction behaviour and determination of cefoperazone using a hanging mercury drop electrode were investigated. Cyclic voltammograms of cefoperazone recorded in universal Britton-Robinson buffers pH 3–6 exhibited a single irreversible cathodic peak. The process was adsorption-controlled. Britton-Robinson buffer 0.04 M pH 4.0 was selected as a supporting electrolyte for quantitative purposes by differential pulse and square wave adsorptive cathodic stripping voltammetry. The experimental voltammetric conditions were optimized using Central Composite Face design. A reduction wave was seen in the range from −0.7 to −0.8 V. These voltammetric techniques were successfully validated as per ICH guidelines and applied for the determination of cefoperazone in its single and sulbactam containing powders for injection and statistically comparable to USP-HPLC. They were further extended to determine cefoperazone in spiked human urine with no matrix effect. PMID:24109542

  2. Adsorptive Cathodic Stripping Voltammetric Determination of Cefoperazone in Bulk Powder, Pharmaceutical Dosage Forms, and Human Urine

    Directory of Open Access Journals (Sweden)

    Vu Dang Hoang

    2013-01-01

    Full Text Available The electroreduction behaviour and determination of cefoperazone using a hanging mercury drop electrode were investigated. Cyclic voltammograms of cefoperazone recorded in universal Britton-Robinson buffers pH 3–6 exhibited a single irreversible cathodic peak. The process was adsorption-controlled. Britton-Robinson buffer 0.04 M pH 4.0 was selected as a supporting electrolyte for quantitative purposes by differential pulse and square wave adsorptive cathodic stripping voltammetry. The experimental voltammetric conditions were optimized using Central Composite Face design. A reduction wave was seen in the range from −0.7 to −0.8 V. These voltammetric techniques were successfully validated as per ICH guidelines and applied for the determination of cefoperazone in its single and sulbactam containing powders for injection and statistically comparable to USP-HPLC. They were further extended to determine cefoperazone in spiked human urine with no matrix effect.

  3. Adsorptive cathodic stripping voltammetric determination of cefoperazone in bulk powder, pharmaceutical dosage forms, and human urine.

    Science.gov (United States)

    Hoang, Vu Dang; Huyen, Dao Thi; Phuc, Phan Hong

    2013-01-01

    The electroreduction behaviour and determination of cefoperazone using a hanging mercury drop electrode were investigated. Cyclic voltammograms of cefoperazone recorded in universal Britton-Robinson buffers pH 3-6 exhibited a single irreversible cathodic peak. The process was adsorption-controlled. Britton-Robinson buffer 0.04 M pH 4.0 was selected as a supporting electrolyte for quantitative purposes by differential pulse and square wave adsorptive cathodic stripping voltammetry. The experimental voltammetric conditions were optimized using Central Composite Face design. A reduction wave was seen in the range from -0.7 to -0.8 V. These voltammetric techniques were successfully validated as per ICH guidelines and applied for the determination of cefoperazone in its single and sulbactam containing powders for injection and statistically comparable to USP-HPLC. They were further extended to determine cefoperazone in spiked human urine with no matrix effect.

  4. Multi-kiloampere, electron-beam generation using metal photo-cathodes driven by ArF and KrF lasers

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, R.L.; Moya, S.A.; Ridlon, R.N.; Seitz, G.J.; Shurter, R.P.

    1996-06-01

    An electron-beam-pumped laser operating at ArF (193 nm) or KrF (248 nm) producing 35 MW (3.5 J in 100 ns) has been used to illuminate a micro-machined aluminum cathode. The cathode was pulsed to 2.75 MV at fields of 185 kV/cm (15-cm AK gap) using REX[1,2](a 4-MV, 5-kA,85-ns) pulsed-diode machine. The extracted current versus incident laser power, and therefore, quantum efficiency was measured for KrF at 5x10{sup -5}; ArF was significantly higher at 1x10{sup -3}. Current densities of 100 A/cm{sup 2} and total currents of 2 kA have been achieved, the latter by increasing the cathode area in proportion to the laser power.

  5. Ion sources with arc-discharge plasma box driven by directly heated LaB(6) electron emitter or cold cathode.

    Science.gov (United States)

    Ivanov, Alexander A; Davydenko, Vladimir I; Deichuli, Petr P; Shulzhenko, Grigori I; Stupishin, Nikolay V

    2008-02-01

    In the Budker Institute, Novosibirsk, an ion source with arc-discharge plasma box has been developed in the recent years for application in thermonuclear devices for plasma diagnostics. Several modifications of the ion source were provided with extracted current ranging from 1 to 7 A and pulse duration of up to 4 s. Initially, the arc-discharge plasma box with cold cathode was used, with which pulse duration is limited to 2 s by the cathode overheating and sputtering in local arc spots. Recently, a directly heated LaB(6) electron emitter was employed instead, which has extended lifetime compared to the cold cathode. In the paper, characteristics of the beam produced with both arrangements of the plasma box are presented.

  6. Metrology in arc plasmas - A new cathode

    Science.gov (United States)

    Croche, R.

    1980-02-01

    A new radiating source consisting of an electric arc under argon pressure is described, with power varying between about 0.2 and 1.5 kW, and with the plasma furnishing a continuous spectrum between 115 and 350 nm. The arc functions from 5 to 50 A, with a voltage varying between 30 and 35 V. The cathode of the transfer arc is described in detail, including such advantages as easy igniting of the arc and the possibility of re-sharpening the tip of the cathode. Most important, the new 'knife-shaped' form of the tungsten cathode has improved the stability and reproducibility of the ultraviolet continuum emitted by the plasma of the arc, which is used at the French National Institute of Metrology as a transfer standard of spectral radiance in the vacuum ultraviolet.

  7. Sheet Plasma Produced by Hollow Cathode Discharge

    Institute of Scientific and Technical Information of China (English)

    张龙; 张厚先; 杨宣宗; 冯春华; 乔宾; 王龙

    2003-01-01

    A sheet plasma is produced by a hollow cathode discharge under an axial magnetic field.The plasma is about 40cm in length,4 cm in width and 1cm in thickness.The electron density is about 108cm-3.The hollow cathode is made to be shallow with a large opening,which is different from the ordinary deep hollow cathode.A Langmuir probe is used to detect the plasma.The electron density and the spatial distribution of the plasma change when voltage,pressure and the magnetic field vary.A peak and a data fluctuation at about 200 G-300 G are observed in the variation of electron density(or thickness of the sheet plasma)with the magnetic field.Our work will be helpful in characterizing the sheet plasma and will make the production of dense sheet plasma more controllable.

  8. 基于空间矢量脉宽调制的三电平逆变器滤波器参数设计%Parameter design of LCL filter for three-level converter based on space vector pulse width modulation

    Institute of Scientific and Technical Information of China (English)

    张国荣; 李讯; 周同路

    2014-01-01

    The neutral-point-clamped (NPC) three-level inverter is used more and more in the grid-connected renewable energy generation system. In order to achieve the lower current harmonic, an LCL filter is also widely utilized due to its superior filtering performance. The LCL filter has the advantages of a high-frequency stopband with good performance and low-frequency compensation ability, but the parameters of LCL are hard to design. Especially the different modulation methods between three-level and two-level inverters, and the different ripple current, all these factors lead to a more difficult design of the parameters. The key of LCL design is the arm-side inductance design, due to the fact that an improper design of arm-side inductance will conduct to a completely different ripple current of the inverter, power loss of the filter components, and larger stress switch stress, thus resulting in poor performance of output current. Moreover, the control of the inverter will be affected. In the design of arm-side inductance, the most important thing is to strike a maximum ripple current. On the basis of establishing the mathematical model of a three-level grid-connected inverter, this paper takes output current control under the unity power factor into consideration, combining with the characters of space vector pulse width modulation (SVPWM) to reach the arm-side ripple current’s variation regularity. The maximum ripple current could be obtained at the peak of a grid side current based on this research. There will always be three latest vectors for the synthesis of the reference vector in accordance with the principle of the Nearest Three Vectors (NTV). In addition, seven-segment modulation on the action time allocation of each vector was applied. Considering the worst case, the value of max ripple current can be obtained when the middle vector was neglected , coupled with the engineering demand for ripple current, and upper limits of arm-side inductance can be given

  9. Synchrotron Investigations of SOFC Cathode Degradation

    Energy Technology Data Exchange (ETDEWEB)

    Idzerda, Yves

    2013-09-30

    The atomic variations occurring in cathode/electrolyte interface regions of La{sub 1-x}Sr{sub x}Co{sub y}Fe{sub 1-y}O{sub 3-δ} (LSCF) cathodes and other SOFC related materials have been investigated and characterized using soft X-ray Absorption Spectroscopy (XAS) and diffuse soft X-ray Resonant Scattering (XRS). X-ray Absorption Spectroscopy in the soft X-ray region (soft XAS) is shown to be a sensitive technique to quantify the disruption that occurs and can be used to suggest a concrete mechanism for the degradation. For LSC, LSF, and LSCF films, a significant degradation mechanism is shown to be Sr out-diffusion. By using the XAS spectra of hexavalent Cr in SrCrO4 and trivalent Cr in Cr2O3, the driving factor for Sr segregation was identified to be the oxygen vacancy concentration at the anode and cathode side of of symmetric LSCF/GDC/LSCF heterostructures. This is direct evidence of vacancy induced cation diffusion and is shown to be a significant indicator of cathode/electrolyte interfacial degradation. X-ray absorption spectroscopy is used to identify the occupation of the A-sites and B-sites for LSC, LSF, and LSCF cathodes doped with other transition metals, including doping induced migration of Sr to the anti-site for Sr, a significant cathode degradation indicator. By using spatially resolved valence mapping of Co, a complete picture of the surface electrochemistry can be determined. This is especially important in identifying degradation phenomena where the degradation is spatially localized to the extremities of the electrochemistry and not the average. For samples that have electrochemical parameters that are measured to be spatially uniform, the Co valence modifications were correlated to the effects of current density, overpotential, and humidity.

  10. MST Filterability Tests

    Energy Technology Data Exchange (ETDEWEB)

    Poirier, M. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Duignan, M. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-03-12

    The Savannah River Site (SRS) is currently treating radioactive liquid waste with the Actinide Removal Process (ARP) and the Modular Caustic Side Solvent Extraction Unit (MCU). The low filter flux through the ARP has limited the rate at which radioactive liquid waste can be treated. Recent filter flux has averaged approximately 5 gallons per minute (gpm). Salt Batch 6 has had a lower processing rate and required frequent filter cleaning. Savannah River Remediation (SRR) has a desire to understand the causes of the low filter flux and to increase ARP/MCU throughput. In addition, at the time the testing started, SRR was assessing the impact of replacing the 0.1 micron filter with a 0.5 micron filter. This report describes testing of MST filterability to investigate the impact of filter pore size and MST particle size on filter flux and testing of filter enhancers to attempt to increase filter flux. The authors constructed a laboratory-scale crossflow filter apparatus with two crossflow filters operating in parallel. One filter was a 0.1 micron Mott sintered SS filter and the other was a 0.5 micron Mott sintered SS filter. The authors also constructed a dead-end filtration apparatus to conduct screening tests with potential filter aids and body feeds, referred to as filter enhancers. The original baseline for ARP was 5.6 M sodium salt solution with a free hydroxide concentration of approximately 1.7 M.3 ARP has been operating with a sodium concentration of approximately 6.4 M and a free hydroxide concentration of approximately 2.5 M. SRNL conducted tests varying the concentration of sodium and free hydroxide to determine whether those changes had a significant effect on filter flux. The feed slurries for the MST filterability tests were composed of simple salts (NaOH, NaNO2, and NaNO3) and MST (0.2 – 4.8 g/L). The feed slurry for the filter enhancer tests contained simulated salt batch 6 supernate, MST, and filter enhancers.

  11. Review on MIEC Cathode Materials for Solid Oxide Fuel Cells

    Science.gov (United States)

    Burnwal, Suman Kumar; Bharadwaj, S.; Kistaiah, P.

    2016-11-01

    The cathode is one of the most important components of solid oxide fuel cells (SOFCs). The reduction of oxygen at the cathode (traditional cathodes like LSM, LSGM, etc.) is the slow step in the cell reaction at intermediate temperature (600-800∘C) which is one of the key obstacles to the development of SOFCs. The mixed ionic and electronic conducting cathode (MIEC) like LSCF, BSCF, etc., has recently been proposed as a promising cathode material for SOFC due to the improvement of the kinetic of the cathode reaction. The MIEC materials provide not only the electrons for the reduction of oxygen, but also the ionic conduction required to ensure the transport of the formed oxygen ions and thereby improves the overall electrochemical performance of SOFC system. The characteristics of MIEC cathode materials and its comparison with other traditional cathode materials is studied and presented in the paper.

  12. Nano-Particle Scandate Cathode for Space Communications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose an improved cathode based on our novel theory of the role of scandium oxide in enhancing emission in tungsten impregnate cathodes. Recent results have...

  13. Long Life Cold Cathodes for Hall effect Thrusters Project

    Data.gov (United States)

    National Aeronautics and Space Administration — An electron source incorporating long life, high current density cold cathodes inside a microchannel plate for use with ion thrusters is proposed. Cathode lifetime...

  14. Klystron Amplifier Utilizing Scandate Cathode and Electrostatic Focusing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to build an electrostatically focused klystron that exploits recent breakthroughs in scandate cathode technology. We have built cathodes with greater than...

  15. Composition and Morphology of Product Layers in the Steel/Cement Paste Interface in Conditions of Corrosion and Cathodic Protection in Reinforced Concrete

    NARCIS (Netherlands)

    Koleva, D.A.; Van Breugel, K.; De Wit, J.H.W.; Fraaij, A.L.A.; Boshkov, N.

    2007-01-01

    The present study explores the formation of corrosion products on the steel surface in reinforced concrete in conditions of corrosion and subsequent transformation of these layers in conditions of cathodic protection (CP). Of particular interest was to investigate if the introduced pulse CP (as cost

  16. Pulsed thermoelectricity

    Science.gov (United States)

    Apostol, M.; Nedelcu, M.

    2010-07-01

    A special mechanism of thermoelectric transport is described, consisting of pulses of charge carriers which "fly" periodically through the external circuit from the hot end of the sample to the cold end, with a determined duration of the "on" and "off" times of the electric contacts, while maintaining continuously the thermal contacts. It is shown that such a "resonant" ideal thermogenerator may work cyclically, with the same efficiency quotient as the ideal efficiency quotient of the thermoelectric devices operated in the usual stationary transport regime but the electric flow and power are increased, as a consequence of the concentration of the charge carriers on pulses of small spatial extent. The process is reversible, in the sense that it can be operated either as a thermoelectric generator or as an electrothermal cooler.

  17. DARHT 2 kA Cathode Development

    Energy Technology Data Exchange (ETDEWEB)

    Henestroza, E.; Houck, T.; Kwan, J.W.; Leitner, M.; Miram, G.; Prichard, B.; Roy, P.K.; Waldron, W.; Westenskow, G.; Yu, S.; Bieniosek, F.M.

    2009-03-09

    In the campaign to achieve 2 kA of electron beam current, we have made several changes to the DARHT-II injector during 2006-2007. These changes resulted in a significant increase in the beam current, achieving the 2 kA milestone. Until recently (before 2007), the maximum beam current that was produced from the 6.5-inch diameter (612M) cathode was about 1300 A when the cathode was operating at a maximum temperature of 1140 C. At this temperature level, the heat loss was dominated by radiation which is proportional to temperature to the fourth power. The maximum operating temperature was limited by the damage threshold of the potted filament and the capacity of the filament heater power supply, as well as the shortening of the cathode life time. There were also signs of overheating at other components in the cathode assembly. Thus it was clear that our approach to increase beam current could not be simply trying to run at a higher temperature and the preferred way was to operate with a cathode that has a lower work function. The dispenser cathode initially used was the type 612M made by SpectraMat. According to the manufacturer's bulletin, this cathode should be able to produce more than 10 A/cm{sup 2} of current density (corresponding to 2 kA of total beam current) at our operating conditions. Instead the measured emission (space charge limited) was 6 A/cm{sup 2}. The result was similar even after we had revised the activation and handling procedures to adhere more closely to the recommend steps (taking longer time and nonstop to do the out-gassing). Vacuum was a major concern in considering the cathode's performance. Although the vacuum gauges at the injector vessel indicated 10{sup -8} Torr, the actual vacuum condition near the cathode in the central region of the vessel, where there might be significant out-gassing from the heater region, was never determined. Poor vacuum at the surface of the cathode degraded the emission (by raising the work function

  18. Hollow-Cathode Source Generates Plasma

    Science.gov (United States)

    Deininger, W. D.; Aston, G.; Pless, L. C.

    1989-01-01

    Device generates argon, krypton, or xenon plasma via thermionic emission and electrical discharge within hollow cathode and ejects plasma into surrounding vacuum. Goes from cold start up to full operation in less than 5 s after initial application of power. Exposed to moist air between operations without significant degradation of starting and running characteristics. Plasma generated by electrical discharge in cathode barrel sustained and aided by thermionic emission from emitter tube. Emitter tube does not depend on rare-earth oxides, making it vulnerable to contamination by exposure to atmosphere. Device modified for use as source of plasma in laboratory experiments or industrial processes.

  19. Low-current hollow-cathode discharge in a trigger unit of a cold cathode thyratron

    OpenAIRE

    Landl, N. V.; Korolev, Yuriy Dmitrievich; Frants, O. B.; Geyman, V. G.; Bolotov, A. V.

    2015-01-01

    The paper deals with the investigations of the effect of cathode emissivity on the regimes of low-current hollow-cathode glow discharge. It is shown that an increase in the emissivity due to the so-called high-emissivity tablet allows the essential decrease in the discharge initiation voltage and the discharge burning voltage. The model of current sustaining for the hollow-cathode discharge, which takes into account the external emission current has been developed. On basis of the model, the ...

  20. Low-current hollow-cathode discharge in a trigger unit of a cold cathode thyratron

    Science.gov (United States)

    Landl, N. V.; Korolev, Y. D.; Frants, O. B.; Geyman, V. G.; Bolotov, A. V.

    2015-11-01

    The paper deals with the investigations of the effect of cathode emissivity on the regimes of low-current hollow-cathode glow discharge. It is shown that an increase in the emissivity due to the so-called high-emissivity tablet allows the essential decrease in the discharge initiation voltage and the discharge burning voltage. The model of current sustaining for the hollow-cathode discharge, which takes into account the external emission current has been developed. On basis of the model, the current-voltage characteristics of the discharge have been interpreted.

  1. A Novel Cathode Material for Cathodic Dehalogenation of 1,1-Dibromo Cyclopropane Derivatives.

    Science.gov (United States)

    Gütz, Christoph; Selt, Maximilian; Bänziger, Markus; Bucher, Christoph; Römelt, Christina; Hecken, Nadine; Gallou, Fabrice; Galvão, Tomás R; Waldvogel, Siegfried R

    2015-09-28

    Leaded bronze turned out to be an excellent cathode material for the dehalogenation reaction of cyclopropanes without affecting the strained molecular entity. With this particular alloy, beneficial properties of lead cathodes are conserved, whereas the corrosion of cathode is efficiently suppressed. The solvent in the electrolyte determines whether a complete debromination reaction is achieved or if the process can be selectively stopped at the monobromo cyclopropane intermediate. The electroorganic conversion tolerates a variety of functional groups and can be conducted at rather complex substrates like cyclosporine A. This approach allows the sustainable preparation of cyclopropane derivatives.

  2. Wireline equalization using pulse-width modulation

    NARCIS (Netherlands)

    Schrader, J.H.R.; Klumperink, Eric A.M.; Visschers, J.L.; Nauta, Bram

    2006-01-01

    Abstract-High-speed data links over copper cables can be effectively equalized using pulse-width modulation (PWM) pre-emphasis. This provides an alternative to the usual 2-tap FIR filters. The use of PWM pre-emphasis allows a channel loss at the Nyquist frequency of ~30dB, compared to ~20dB for a

  3. Intense Pulsed Heavy Ion Beam Technology

    Science.gov (United States)

    Masugata, Katsumi; Ito, Hiroaki

    Development of intense pulsed heavy ion beam accelerator technology is described for the application of materials processing. Gas puff plasma gun and vacuum arc discharge plasma gun were developed as an active ion source for magnetically insulated pulsed ion diode. Source plasma of nitrogen and aluminum were successfully produced with the gas puff plasma gun and the vacuum arc plasma gun, respectively. The ion diode was successfully operated with gas puff plasma gun at diode voltage 190 kV, diode current 2.2 kA and nitrogen ion beam of ion current density 27 A/cm2 was obtained. The ion composition was evaluated by a Thomson parabola spectrometer and the purity of the nitrogen ion beam was estimated to be 86%. The diode also operated with aluminum ion source of vacuum arc plasma gun. The ion diode was operated at 200 kV, 12 kA, and aluminum ion beam of current density 230 A/cm2 was obtained. The beam consists of aluminum ions (Al(1-3)+) of energy 60-400 keV, and protons (90-130 keV), and the purity was estimated to be 89 %. The development of the bipolar pulse accelerator (BPA) was reported. A double coaxial type bipolar pulse generator was developed as the power supply of the BPA. The generator was tested with dummy load of 7.5 ohm, bipolar pulses of -138 kV, 72 ns (1st pulse) and +130 kV, 70 ns (2nd pulse) were succesively generated. By applying the bipolar pulse to the drift tube of the BPA, nitrogen ion beam of 2 A/cm2 was observed in the cathode, which suggests the bipolar pulse acceleration.

  4. Guided image filtering.

    Science.gov (United States)

    He, Kaiming; Sun, Jian; Tang, Xiaoou

    2013-06-01

    In this paper, we propose a novel explicit image filter called guided filter. Derived from a local linear model, the guided filter computes the filtering output by considering the content of a guidance image, which can be the input image itself or another different image. The guided filter can be used as an edge-preserving smoothing operator like the popular bilateral filter [1], but it has better behaviors near edges. The guided filter is also a more generic concept beyond smoothing: It can transfer the structures of the guidance image to the filtering output, enabling new filtering applications like dehazing and guided feathering. Moreover, the guided filter naturally has a fast and nonapproximate linear time algorithm, regardless of the kernel size and the intensity range. Currently, it is one of the fastest edge-preserving filters. Experiments show that the guided filter is both effective and efficient in a great variety of computer vision and computer graphics applications, including edge-aware smoothing, detail enhancement, HDR compression, image matting/feathering, dehazing, joint upsampling, etc.

  5. Uniform large-area thermionic cathode for SCALPEL

    Science.gov (United States)

    Katsap, Victor; Sewell, Peter B.; Waskiewicz, Warren K.; Zhu, Wei

    1999-11-01

    An electron beam lithography tool, which employs the SCALPEL technique, requires an extremely uniform beam to illuminate the scattering Mask, with the cathode operating in the temperature limited mode. It has been previously shown that LaB6 cathodes are not stable in this mode of operation. We have explored the possibility of implementing refined Tantalum-based emitters in the SCALPEL source cathode, and have developed large-area flat cathodes featuring suitably high emission uniformity under temperature limited operation.

  6. Improved image filter based on SPCNN

    Institute of Scientific and Technical Information of China (English)

    ZHANG YuDong; WU LeNan

    2008-01-01

    By extraction of the thoughts of non-linear model and adaptive model match, an improved Nagao filter is brought. Meanwhile a technique based on simplified pulse coupled neural network and used for noise positioning, is put forward. Combining the two methods above, we acquire a new method that can restore images corrupted by salt and pepper noise. Experiments show that this method is more preferable than other popular ones, and still works well while noise density fluctuates severely.

  7. Modular Low-Heater-Power Cathode/Electron Gun Assembly for Microwave and Millimeter Wave Traveling Wave Tubes

    Science.gov (United States)

    Wintucky, Edwin G.

    2000-01-01

    cathode/electron gun assembly consists of four subassemblies the cathode, the focus electrode, the header (including the electrical feedthroughs), and the gun envelope (including the anode) a diagram of which is shown. The modular construction offers a number of significant advantages, including flexibility of design, interchangeability of parts, and a drop-in final assembly procedure for quick and accurate alignment. The gun can accommodate cathodes ranging in size from 0.050 to 0.250-in. in diameter and is applicable to TWT's over a broad range of sizes and operating parameters, requiring the substitution of only a few parts: that is, the cathode, focus electrode, and anode. The die-pressed cathode pellets can be made with either flat or concave (Pierce gun design) emitting surfaces. The gun can be either gridded (pulse operation) or ungridded (continuous operation). Important factors contributing to low cost are the greater use of CRT materials and parts, the standardization of processes (welding and mechanical capture), and tooling amenable to automated production. Examples are the use of simple shapes, drawn or stamped metal parts, and parts joined by welding or mechanical capture. Feasibility was successfully demonstrated in the retrofit and testing of a commercial Kaband (22-GHz) TWT. The modular cathode/electron gun assembly was computer modeled to replicate the performance of the original electron gun and fabricated largely from existing CRT parts. Significant test results included demonstration of low heater power (1.5-W, 1010 C brightness temperature for a 0.085-in.-diameter cathode), mechanical ruggedness (100g shock and vibration tests in accordance with military specifications (MIL specs)), and a very fast warmup. The results of these tests indicate that the low-cost CRT manufacturing approach can be used without sacrificing performance and reliability.

  8. Optical properties of lamps with cold emission cathode

    Science.gov (United States)

    Kalenik, Jerzy; Czerwosz, ElŻbieta; Biernacki, Krzysztof; Rymarczyk, Joanna; Stepińska, Izabela

    2016-12-01

    A luminescent lamp was constructed and tested. Phosphor excited by electrons is the source of light. The source of electrons is field emission cathode. The cathode is covered with nickel-carbon layer containing carbon nanotubes that enhance electron emission from the cathode. Results of luminance measurements are presented. Luminance is high enough for lighting application.

  9. Characterization and Failure Analysis of Ceramic Filters Utilized for Emission Control Coal Gasification

    Energy Technology Data Exchange (ETDEWEB)

    Daniel Mei; Jianren Zhou; Ziaul Huque

    1998-03-01

    Advanced integrated gasification combined cycle (IGCC) and pressurized fluidized bed combustion (PFBC) power system requires both hot gas desulfurization and particulate filtration to improve system thermal efficiency and overall performance. Therefore, effective high temperature ceramic filters are indispensable key component in both of the advanced IGCC and PFBC coal based power systems to perform hot gas cleanup work. To meet the environmental particulate emission requirements and improve thermal efficiency, ceramic filters are mainly utilized to cleanup the hot gas particulate to protect downstream heat exchanger and gas turbine components from fouling and corrosion. The mechanical integrity of ceramic filters and an efficient dust cake removal system are the key issues for hot gas cleanup systems. The filters must survive combined stresses due to mechanical, thermal, chemical and steam attack throughout normal operations (cold back pulse cleaning jets), unexpected excessive ash accumulation, and the start up and shut down conditions. To evaluate the design and performance of ceramic filters, different long term filter testing programs were conducted. To fulfill this purpose, two Advanced Particle Filter (APF) systems were complete at Tidd PFBC Demonstration Plant, in Brilliant, Ohio in late 1990 as part of the Department of Energy's (DOE) Clean Coal Technology Program. But the most undesirable thing ever happened was the sudden functional and physical failures of filters prior to its designed life time. In Tidd APF filter vessel, twenty eight (28) filters failed one time. Significant research effort has been carried out to find out the causes that led to the early failure of filters. In this work, the studies are emphasized on the possible failure causes analysis of rigid ceramic candle filters. The objectives of this program were to provide an systematic study on the characterization of filters, material laboratory analysis on filter micro-structure, the

  10. Computer Aided Filter Design.

    Science.gov (United States)

    1987-12-01

    FIR filter can be described in the following. [Ref. 2] 1. FIR filters with exact linear phase can be easily designed. Linear phase filters are important...response for the four cases of linear phase filter , i.e., even or odd symmetry with an even or odd number of terms, can be written in the form: H (eJ ) = e...Ansari, The Design and Application of Optimal FIR Fractional Phase Filters , IEEE on Acoutics, Speech and Signal Processing, Vol. 2, 1987, pp.896-899. 77 14

  11. A unified Kalman filter

    Science.gov (United States)

    Stubberud, Allen R.

    2017-01-01

    When considering problems of linear sequential estimation, two versions of the Kalman filter, the continuous-time version and the discrete-time version, are often used. (A hybrid filter also exists.) In many applications in which the Kalman filter is used, the system to which the filter is applied is a linear continuous-time system, but the Kalman filter is implemented on a digital computer, a discrete-time device. The two general approaches for developing a discrete-time filter for implementation on a digital computer are: (1) approximate the continuous-time system by a discrete-time system (called discretization of the continuous-time system) and develop a filter for the discrete-time approximation; and (2) develop a continuous-time filter for the system and then discretize the continuous-time filter. Generally, the two discrete-time filters will be different, that is, it can be said that discretization and filter generation are not, in general, commutative operations. As a result, any relationship between the discrete-time and continuous-time versions of the filter for the same continuous-time system is often obfuscated. This is particularly true when an attempt is made to generate the continuous-time version of the Kalman filter through a simple limiting process (the sample period going to zero) applied to the discrete-time version. The correct result is, generally, not obtained. In a 1961 research report, Kalman showed that the continuous-time Kalman filter can be obtained from the discrete-time Kalman filter by taking limits as the sample period goes to zero if the white noise process for the continuous-time version is appropriately defined. Using this basic concept, a discrete-time Kalman filter can be developed for a continuous-time system as follows: (1) discretize the continuous-time system using Kalman's technique; and (2) develop a discrete-time Kalman filter for that discrete-time system. Kalman's results show that the discrete-time filter generated in

  12. Bias aware Kalman filters

    DEFF Research Database (Denmark)

    Drecourt, J.-P.; Madsen, H.; Rosbjerg, Dan

    2006-01-01

    . The colored noise filter formulation is extended to correct both time correlated and uncorrelated model error components. A more stable version of the separate filter without feedback is presented. The filters are implemented in an ensemble framework using Latin hypercube sampling. The techniques...... are illustrated on a simple one-dimensional groundwater problem. The results show that the presented filters outperform the standard Kalman filter and that the implementations with bias feedback work in more general conditions than the implementations without feedback. 2005 Elsevier Ltd. All rights reserved....

  13. LOW TEMPERATURE CATHODE SUPPORTED ELECTROLYTES

    Energy Technology Data Exchange (ETDEWEB)

    Harlan U. Anderson

    2000-03-31

    . However, they have the potential of being useful as an interface on the anode side of the electrolyte. NexTech has focused much of its effort during the past few months on establishing tape casting methods for porous LSM substrates. This work, performed under a separate DOE-funded program, involved tape casting formulations comprising LSM powders with bi-modal particle size distributions and fugitive pore forming additives. Sintered LSM substrates with porosities in the 30 to 40 vol% range, and pore sizes of 10 {approx} 20 microns have been prepared. In addition, tape casting formulations involving composite mixtures of LSM and Sm-doped ceria (SDC) have been evaluated. The LSM/SDC cathode substrates are expected to provide better performance at low temperatures. Characterization of these materials is currently underway.

  14. LOW TEMPERATURE CATHODE SUPPORTED ELECTROLYTES

    Energy Technology Data Exchange (ETDEWEB)

    Harlan U. Anderson; Wayne Huebner; Igor Kosacki

    2001-09-30

    This project has three main goals: Thin Films Studies, Preparation of Graded Porous Substrates and Basic Electrical Characterization and testing of Planar Single Cells. In this portion of study we have focused on producing YSZ films on porous LSM substrates. When using the polymer precursor there are a number of obstacles to overcome in order to form dense electrolyte layers on porous substrates (cathode or anode). Probably the most difficult problems are: (1) Extreme penetration of the polymer into the substrate must be prevented. (2) Shrinkage cracking must be avoided. (3) Film thickness in the 1 to 5{micro}m range must be achieved. We have demonstrated that cracking due to shrinkage involved during the elimination of solvents and organic matter and densification of the remaining oxide is not a problem as long as the resulting oxide film is < {approx} 0.15 {micro}m in thickness. We have also shown that we can make thicker films by making multiple depositions if the substrate is smooth (roughness {le} 0.1 {micro}m) and contains no surface pores > 0.2 {micro}m. The penetration of the polymer into the porous substrate can be minimized by increasing the viscosity of the polymer and reducing the largest pore at the surface of the substrate to {le} 0.2 {micro}m. We have shown that this can be done, but we have also shown that it is difficult to make dense films that are defect free with areas > 1 cm{sup 2}. This is because of the roughness of the substrate and the difficulty in making a substrate which does not have surface voids > 0.2 {micro}m. Thus the process works well for dense, smooth substrates for films < 1 {micro}m thick, but is difficult to apply to rough, porous surfaces and to make film thickness > 1 {micro}m. As a result of these problems, we have been addressing the issue of how to make dense films in the thickness range of 1 to 5 {micro}m on sintered porous substrates without introducing cracks and holes due to shrinkage and surface voids? These

  15. The double sheath on cathodes of discharges burning in cathode vapour

    Energy Technology Data Exchange (ETDEWEB)

    Benilov, M S; Benilova, L G [Departamento de Fisica, Universidade da Madeira, Largo do MunicIpio, 9000 Funchal (Portugal)

    2010-09-01

    The model of a collisionless near-cathode space-charge sheath with ionization of atoms emitted by the cathode surface is considered. Numerical calculations showed that the mathematical problem is solvable and its solution is unique. In the framework of this model, the sheath represents a double layer with a potential maximum, with the ions which are produced before the maximum returning to the cathode surface and those produced after the maximum escaping into the plasma. Numerical results are given in a form to be readily applicable in analysis of discharges burning in cathode vapour, such as vacuum arcs. In particular, the results indicate that the ion backflow coefficient in such discharges exceeds 0.5, in agreement with values extracted from the experiment.

  16. Multi scale feature based matched filter processing

    Institute of Scientific and Technical Information of China (English)

    LI Jun; HOU Chaohuan

    2004-01-01

    Using the extreme difference of self-similarity and kurtosis at large level scale of wavelet transform approximation between the PTFM (Pulse Trains of Frequency Modulated)signals and its reverberation, a feature-based matched filter method using the classify-beforedetect paragriam is proposed to improve the detection performance in reverberation and multipath environments. Processing the data of lake-trails showed that the processing gain of the proposed method is bigger than that of matched filter about 10 dB. In multipath environments, detection performance of matched filter become badly poorer, while that of the proposed method is improved better. It shows that the method is much more robust with the effect of multipath.

  17. Ceramic fiber filter technology

    Energy Technology Data Exchange (ETDEWEB)

    Holmes, B.L.; Janney, M.A.

    1996-06-01

    Fibrous filters have been used for centuries to protect individuals from dust, disease, smoke, and other gases or particulates. In the 1970s and 1980s ceramic filters were developed for filtration of hot exhaust gases from diesel engines. Tubular, or candle, filters have been made to remove particles from gases in pressurized fluidized-bed combustion and gasification-combined-cycle power plants. Very efficient filtration is necessary in power plants to protect the turbine blades. The limited lifespan of ceramic candle filters has been a major obstacle in their development. The present work is focused on forming fibrous ceramic filters using a papermaking technique. These filters are highly porous and therefore very lightweight. The papermaking process consists of filtering a slurry of ceramic fibers through a steel screen to form paper. Papermaking and the selection of materials will be discussed, as well as preliminary results describing the geometry of papers and relative strengths.

  18. Processing of X-ray Microcalorimeter Data with Pulse Shape Variation using Principal Component Analysis

    CERN Document Server

    Yan, Daikang; Gades, Lisa; Jacobsen, Chris; Madden, Timothy; Miceli, Antonino

    2016-01-01

    We present a method using principal component analysis (PCA) to process x-ray pulses with severe shape variation where traditional optimal filter methods fail. We demonstrate that PCA is able to noise-filter and extract energy information from x-ray pulses despite their different shapes. We apply this method to a dataset from an x-ray thermal kinetic inductance detector which has severe pulse shape variation arising from position-dependent absorption.

  19. ME1/1 Cathode Strip Chambers

    CERN Document Server

    Erchov, Yu V; Kamenev, Alexey; Karjavin, Vladimir; Khabarov, Serguei; Moissenz, P V; Moissenz, K P; Movchan, Sergey; Perelygin, Victor; Vassiliev, S E; Zarubin, Anatoli; Tchekhovski, V A

    2008-01-01

    The 76 innermost ME1/1 cathode strip chambers (CSC) of the CMS Experiment were designed and produced in Dubna. The chambers have been installed in the detector and commissioning has been completed. This paper describes the design of the CSCs, their main mechanical parameters and read-out electronics, and the results of tests with cosmic-ray muons.

  20. Barium depletion in hollow cathode emitters

    Energy Technology Data Exchange (ETDEWEB)

    Polk, James E., E-mail: james.e.polk@jpl.nasa.gov; Mikellides, Ioannis G.; Katz, Ira [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, California 91109 (United States); Capece, Angela M. [Graduate Aerospace Laboratories, California Institute of Technology, Pasadena, California 91125 (United States)

    2016-01-14

    Dispenser hollow cathodes rely on a consumable supply of Ba released by BaO-CaO-Al{sub 2}O{sub 3} source material in the pores of a tungsten matrix to maintain a low work function surface. The examination of cathode emitters from long duration tests shows deposits of tungsten at the downstream end that appear to block the flow of Ba from the interior. In addition, a numerical model of Ba transport in the cathode plasma indicates that the Ba partial pressure in the insert may exceed the equilibrium vapor pressure of the dominant Ba-producing reaction, and it was postulated previously that this would suppress Ba loss in the upstream part of the emitter. New measurements of the Ba depletion depth from a cathode insert operated for 8200 h reveal that Ba loss is confined to a narrow region near the downstream end, confirming this hypothesis. The Ba transport model was modified to predict the depletion depth with time. A comparison of the calculated and measured depletion depths gives excellent qualitative agreement, and quantitative agreement was obtained assuming an insert temperature 70 °C lower than measured beginning-of-life values.

  1. Digital high-pass filter deconvolution by means of an infinite impulse response filter

    Science.gov (United States)

    Födisch, P.; Wohsmann, J.; Lange, B.; Schönherr, J.; Enghardt, W.; Kaever, P.

    2016-09-01

    In the application of semiconductor detectors, the charge-sensitive amplifier is widely used in front-end electronics. The output signal is shaped by a typical exponential decay. Depending on the feedback network, this type of front-end electronics suffers from the ballistic deficit problem, or an increased rate of pulse pile-ups. Moreover, spectroscopy applications require a correction of the pulse-height, while a shortened pulse-width is desirable for high-throughput applications. For both objectives, digital deconvolution of the exponential decay is convenient. With a general method and the signals of our custom charge-sensitive amplifier for cadmium zinc telluride detectors, we show how the transfer function of an amplifier is adapted to an infinite impulse response (IIR) filter. This paper investigates different design methods for an IIR filter in the discrete-time domain and verifies the obtained filter coefficients with respect to the equivalent continuous-time frequency response. Finally, the exponential decay is shaped to a step-like output signal that is exploited by a forward-looking pulse processing.

  2. Digital high-pass filter deconvolution by means of an infinite impulse response filter

    Energy Technology Data Exchange (ETDEWEB)

    Födisch, P., E-mail: p.foedisch@hzdr.de [Helmholtz-Zentrum Dresden - Rossendorf, Department of Research Technology, Bautzner Landstr. 400, 01328 Dresden (Germany); Wohsmann, J. [Helmholtz-Zentrum Dresden - Rossendorf, Department of Research Technology, Bautzner Landstr. 400, 01328 Dresden (Germany); Dresden University of Applied Sciences, Faculty of Electrical Engineering, Friedrich-List-Platz 1, 01069 Dresden (Germany); Lange, B. [Helmholtz-Zentrum Dresden - Rossendorf, Department of Research Technology, Bautzner Landstr. 400, 01328 Dresden (Germany); Schönherr, J. [Dresden University of Applied Sciences, Faculty of Electrical Engineering, Friedrich-List-Platz 1, 01069 Dresden (Germany); Enghardt, W. [OncoRay - National Center for Radiation Research in Oncology, Faculty of Medicine and University Hospital Carl Gustav Carus, Technische Universität Dresden, Fetscherstr. 74, PF 41, 01307 Dresden (Germany); Helmholtz-Zentrum Dresden - Rossendorf, Institute of Radiooncology, Bautzner Landstr. 400, 01328 Dresden (Germany); German Cancer Consortium (DKTK) and German Cancer Research Center (DKFZ), Im Neuenheimer Feld 280, 69120 Heidelberg (Germany); Kaever, P. [Helmholtz-Zentrum Dresden - Rossendorf, Department of Research Technology, Bautzner Landstr. 400, 01328 Dresden (Germany); Dresden University of Applied Sciences, Faculty of Electrical Engineering, Friedrich-List-Platz 1, 01069 Dresden (Germany)

    2016-09-11

    In the application of semiconductor detectors, the charge-sensitive amplifier is widely used in front-end electronics. The output signal is shaped by a typical exponential decay. Depending on the feedback network, this type of front-end electronics suffers from the ballistic deficit problem, or an increased rate of pulse pile-ups. Moreover, spectroscopy applications require a correction of the pulse-height, while a shortened pulse-width is desirable for high-throughput applications. For both objectives, digital deconvolution of the exponential decay is convenient. With a general method and the signals of our custom charge-sensitive amplifier for cadmium zinc telluride detectors, we show how the transfer function of an amplifier is adapted to an infinite impulse response (IIR) filter. This paper investigates different design methods for an IIR filter in the discrete-time domain and verifies the obtained filter coefficients with respect to the equivalent continuous-time frequency response. Finally, the exponential decay is shaped to a step-like output signal that is exploited by a forward-looking pulse processing.

  3. Improved Rare-Earth Emitter Hollow Cathode

    Science.gov (United States)

    Goebel, Dan M.

    2011-01-01

    An improvement has been made to the design of the hollow cathode geometry that was created for the rare-earth electron emitter described in Compact Rare Earth Emitter Hollow Cathode (NPO-44923), NASA Tech Briefs, Vol. 34, No. 3 (March 2010), p. 52. The original interior assembly was made entirely of graphite in order to be compatible with the LaB6 material, which cannot be touched by metals during operation due to boron diffusion causing embrittlement issues in high-temperature refractory materials. Also, the graphite tube was difficult to machine and was subject to vibration-induced fracturing. This innovation replaces the graphite tube with one made out of refractory metal that is relatively easy to manufacture. The cathode support tube is made of molybdenum or molybdenum-rhenium. This material is easily gun-bored to near the tolerances required, and finish machined with steps at each end that capture the orifice plate and the mounting flange. This provides the manufacturability and robustness needed for flight applications, and eliminates the need for expensive e-beam welding used in prior cathodes. The LaB6 insert is protected from direct contact with the refractory metal tube by thin, graphite sleeves in a cup-arrangement around the ends of the insert. The sleeves, insert, and orifice plate are held in place by a ceramic spacer and tungsten spring inserted inside the tube. To heat the cathode, an insulating tube is slipped around the refractory metal hollow tube, which can be made of high-temperature materials like boron nitride or aluminum nitride. A screw-shaped slot, or series of slots, is machined in the outside of the ceramic tube to constrain a refractory metal wire wound inside the slot that is used as the heater. The screw slot can hold a single heater wire that is then connected to the front of the cathode tube by tack-welding to complete the electrical circuit, or it can be a double slot that takes a bifilar wound heater with both leads coming out

  4. Bent paths of a positive streamer and a cathode-directed spark leader in diffuse discharges preionized by runaway electrons

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Cheng; Shao, Tao, E-mail: st@mail.iee.ac.cn; Wang, Ruixue; Yan, Ping [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China); Key Laboratory of Power Electronics and Electric Drive, Chinese Academy of Sciences, Beijing 100190 (China); Tarasenko, Viktor F.; Beloplotov, Dmitry V.; Lomaev, Mikhail I.; Sorokin, Dmitry A. [Institute of High Current Electronics, Russian Academy of Science, Tomsk 634055 (Russian Federation); National Research Tomsk State University, 36 Lenin Ave., Tomsk 634050 (Russian Federation)

    2015-03-15

    Diffuse discharges preionized by runaway electrons can produce large-area homogeneous discharges at elevated pressures, which is an intriguing phenomenon in the physics of pulsed discharges. In this paper, runaway-electron-preionized diffuse discharge (REP DD) was obtained in a wide pressure range (0.05–0.25 MPa), and under certain conditions a positive streamer and a cathode-directed spark leader could be observed to propagate at some angles to the applied (background) electric field lines. For a 16-mm gap at an air pressure of 0.08–0.1 MPa, the percentage of pulses in which such propagation is observed is about 5%–50% of their total number, and in the other pulses such bent paths could not be observed because there is even no streamer or cathode-directed spark leader in diffuse discharges. In our opinion, such propagation of the positive streamer and the cathode-directed spark leader at some angle to the background electric field lines owes to different increase rates of the electron density in different regions of the discharge volume under REP DD conditions. Therefore, during the formation of a REP DD, the increase of the electron density is inhomogeneous and nonsimultaneous, resulting in an electron density gradient at the ionization wave front.

  5. Study of the prebreakdown stage of a gas discharge in a diode with point cathode by laser probing

    Science.gov (United States)

    Parkevich, E. V.; Tkachenko, S. I.; Agafonov, A. V.; Mingaleev, A. R.; Romanova, V. M.; Shelkovenko, T. A.; Pikuz, S. A.

    2017-04-01

    The prebreakdown stage of a gas discharge in a diode with strongly overloaded cathode is studied by laser methods (by simultaneous use of multiframe interferometry and shadow and schlieren photographing) at atmospheric pressure. The spatial resolution of the methods is about 20 μm. A probing pulse of a laser (LS-2151 Nd: YAG laser with a half amplitude duration of 70 ps and a pulse energy of up to 40 mJ) is synchronized with a voltage pulse with accuracy of about 1 ns. High field strength at the cathode is achieved due to the use of thin individual metal tips on the electrodes. It is shown that the initial stage of breakdown of a discharge gap is accompanied by the emergence of a dense plasma cloud at the end of a tip with electron density of about 5 × 1019 cm-3 with a size of tens of microns, as well as by a sharp increase in the total current through the diode. After the emergence of a dense plasma cloud at the end of a cathode tip, a similar cloud is formed on the surface of the anode; sometime later, these clouds join together and form a tubular current channel. The dynamics of the breakdown, as well as the parameters of the plasma are studied by the abovementioned techniques in three independent optical channels.

  6. Bent paths of a positive streamer and a cathode-directed spark leader in diffuse discharges preionized by runaway electrons

    Science.gov (United States)

    Zhang, Cheng; Tarasenko, Viktor F.; Shao, Tao; Beloplotov, Dmitry V.; Lomaev, Mikhail I.; Wang, Ruixue; Sorokin, Dmitry A.; Yan, Ping

    2015-03-01

    Diffuse discharges preionized by runaway electrons can produce large-area homogeneous discharges at elevated pressures, which is an intriguing phenomenon in the physics of pulsed discharges. In this paper, runaway-electron-preionized diffuse discharge (REP DD) was obtained in a wide pressure range (0.05-0.25 MPa), and under certain conditions a positive streamer and a cathode-directed spark leader could be observed to propagate at some angles to the applied (background) electric field lines. For a 16-mm gap at an air pressure of 0.08-0.1 MPa, the percentage of pulses in which such propagation is observed is about 5%-50% of their total number, and in the other pulses such bent paths could not be observed because there is even no streamer or cathode-directed spark leader in diffuse discharges. In our opinion, such propagation of the positive streamer and the cathode-directed spark leader at some angle to the background electric field lines owes to different increase rates of the electron density in different regions of the discharge volume under REP DD conditions. Therefore, during the formation of a REP DD, the increase of the electron density is inhomogeneous and nonsimultaneous, resulting in an electron density gradient at the ionization wave front.

  7. PULSE COLUMN

    Science.gov (United States)

    Grimmett, E.S.

    1964-01-01

    This patent covers a continuous countercurrent liquidsolids contactor column having a number of contactor states each comprising a perforated plate, a layer of balls, and a downcomer tube; a liquid-pulsing piston; and a solids discharger formed of a conical section at the bottom of the column, and a tubular extension on the lowest downcomer terminating in the conical section. Between the conical section and the downcomer extension is formed a small annular opening, through which solids fall coming through the perforated plate of the lowest contactor stage. This annular opening is small enough that the pressure drop thereacross is greater than the pressure drop upward through the lowest contactor stage. (AEC)

  8. Cathode depth sensing in CZT detectors

    Science.gov (United States)

    Hong, JaeSub; Bellm, Eric C.; Grindlay, Jonathan E.; Narita, Tomohiko

    2004-02-01

    Measuring the depth of interaction in thick Cadmium-Zinc-Telluride (CZT) detectors allows improved imaging and spectroscopy for hard X-ray imaging above 100 keV. The Energetic X-ray Imaging Survey Telescope (EXIST) will employ relatively thick (5 - 10 mm) CZT detectors, which are required to perform the broad energy-band sky survey. Interaction depth information is needed to correct events to the detector "focal plane" for correct imaging and can be used to improve the energy resolution of the detector at high energies by allowing event-based corrections for incomplete charge collection. Background rejection is also improved by allowing low energy events from the rear and sides of the detector to be rejected. We present experimental results of intereaction depth sensing in a 5 mm thick pixellated Au-contact IMARAD CZT detector. The depth sensing was done by making simultaneous measurements of cathode and anode signals, where the interaction depth at a given energy is proportional to the ratio of cathode/anode signals. We demonstrate how a simple empirical formula describing the event distributions in the cathode/anode signal space can dramatically improve the energy resolution. We also estimate the energy and depth resolution of the detector as a function of the energy and the interaction depth. We also show a depth-sensing prototype system currently under development for EXIST in which cathode signals from 8, 16 or 32 crystals can be read-out by a small multi-channel ASIC board that is vertically edge-mounted on the cathode electrode along every second CZT crystal boundary. This allows CZT crystals to be tiled contiguously with minimum impact on throughput of incoming photons. The robust packaging is crucial in EXIST, which will employ very large area imaging CZT detector arrays.

  9. Progress of air-breathing cathode in microbial fuel cells

    Science.gov (United States)

    Wang, Zejie; Mahadevan, Gurumurthy Dummi; Wu, Yicheng; Zhao, Feng

    2017-07-01

    Microbial fuel cell (MFC) is an emerging technology to produce green energy and vanquish the effects of environmental contaminants. Cathodic reactions are vital for high electrical power density generated from MFCs. Recently tremendous attentions were paid towards developing high performance air-breathing cathodes. A typical air-breathing cathode comprises of electrode substrate, catalyst layer, and air-diffusion layer. Prior researches demonstrated that each component influenced the performance of air-breathing cathode MFCs. This review summarized the progress in development of the individual component and elaborated main factors to the performance of air-breathing cathode.

  10. Three-zone pupil filters

    Science.gov (United States)

    Sheppard, Colin J. R.; Campos, Juan; Escalera, Juan C.; Ledesma, Silvia

    2008-07-01

    The performance of pupil filters consisting of three zones each of constant complex amplitude transmittance is investigated. For filters where the transmittance is real, different classes of potentially useful filter are identified. These include leaky filters with an inner zone of low amplitude transmittance, pure phase filters with phase change of π, and equal area filters.

  11. Pulse-train solutions and excitability in an optoelectronic oscillator

    Science.gov (United States)

    Rosin, D. P.; Callan, K. E.; Gauthier, D. J.; Schöll, E.

    2011-11-01

    We study an optoelectronic time-delay oscillator with bandpass filtering for different values of the filter bandwidth. Our experiments show novel pulse-train solutions with pulse widths that can be controlled over a three-order-of-magnitude range, with a minimum pulse width of ~150 ps. The equations governing the dynamics of our optoelectronic oscillator are similar to the FitzHugh-Nagumo model from neurodynamics with delayed feedback in the excitable and oscillatory regimes. Using a nullclines analysis, we derive an analytical proportionality between pulse width and the low-frequency cutoff of the bandpass filter, which is in agreement with experiments and numerical simulations. Furthermore, the nullclines help to describe the shape of the waveforms.

  12. Cesium telluride cathodes for the next generation of high-average current high-brightness photoinjectors

    Energy Technology Data Exchange (ETDEWEB)

    Filippetto, D., E-mail: dfilippetto@lbl.gov; Qian, H.; Sannibale, F. [Lawrence Berkeley National Laboratory, One Cyclotron Road, Berkeley, California 94720 (United States)

    2015-07-27

    We report on the performances of a Cs{sub 2}Te photocathode under extreme conditions of high peak time-dependent accelerating fields, continuous wave operations, and MHz pulse extraction with up to 0.3 mA average current. The measurements, performed in a normal conducting cavity, show extended lifetime and robustness, elucidate the main mechanisms for cathode degradation, and set the required system vacuum performance for compatibility with the operations of a high average power X-ray free electron laser user facility, opening the doors to the next generation of MHz-scale ultrafast scientific instruments.

  13. High-current electron gun with a planar magnetron integrated with an explosive-emission cathode

    Science.gov (United States)

    Kiziridi, P. P.; Ozur, G. E.

    2017-05-01

    A new high-current electron gun with plasma anode and explosive-emission cathode integrated with planar pulsed powered magnetron is described. Five hundred twelve copper wires 1 mm in diameter and 15 mm in height serve as emitters. These emitters are installed on stainless steel disc (substrate) with 3-mm distance between them. Magnetron discharge plasma provides increased ion density on the periphery of plasma anode formed by high-current Penning discharge ignited within several milliseconds after starting of the magnetron discharge. The increased on the periphery ion density improves the uniformity of high-current electron beam produced in such an electron gun.

  14. Cathodic adsorptive stripping square-wave voltammetry of the anti-inflammatory drug meloxicam.

    Science.gov (United States)

    Radi, A E; Ghoneim, M; Beltagi, A

    2001-10-01

    The adsorptive behavior of the anti-inflammatory drug meloxicam was studied by cyclic, differentia-pulse and square-wave voltammetry on a hanging mercury drop electrode (HMDE). The drug was accumulated at HMDE and a well-defined stripping peak current was obtained at -1.42 V vs. Ag/AgCl (saturated KCl) electrode in acetate buffer solution (pH 5.0). A voltammetric procedure was developed for the determination of meloxicam using square-wave cathodic adsorptive stripping voltammetry (SW-CASV). The optimum working conditions for the determination of the drug were established. The analysis of meloxicam in human plasma was carried out satisfactorily.

  15. Stabilization of a cold cathode electron beam glow discharge for surface treatment

    Energy Technology Data Exchange (ETDEWEB)

    Mingolo, N.; Gonzalez, C.R. [Lab. de Haces Dirigidos, Depto. de Fisica, Facultad de Ingenieria, Universidad de Buenos Aires, Paseo Colon 850, 1063 Buenos Aires (Argentina); Martinez, O.E. [Lab. de Electronica Cuantica, Depto. de Fisica, Universidad de Buenos Aires, Pabellon 1, Ciudad Universitaria, 1428 Buenos Aires (Argentina); Rocca, J.J. [Department of Electrical Engineering, Colorado State University, Fort Collins, Colorado 80523 (United States)

    1997-10-01

    We have demonstrated that the reproducibility of electron beam pulses generated by a high power, cold cathode glow discharge is greatly improved by adding a small continuous keep-alive discharge current. A current of the order of 200 {mu}A was found to limit the shot to shot current variation to within 1.5{percent}. This stabilization in turn reduces by an order of magnitude the fluctuations of the energy density deposited on the target, demonstrating a reliable energy source for surface treatment. {copyright} {ital 1997 American Institute of Physics.}

  16. Pulsed Compression for Aerosol Ranging with Coherent Pulse-Doppler Lidar Systems

    Science.gov (United States)

    1990-12-01

    generation technique requires an impulse function or short time duration pulse as the input to a dispersive phase filter . The frequency transfer...function H(f) of the dispersive phase filter can be expressed in general as H(f) = IH(f)Iexp lU(f)] (122) where the magnitude of the transfer function IH(f...response of the dispersive phase filter to a short time duration signal with large bandwidth B is a long time duration signal with the bandwidth B of

  17. Polymer coatings as separator layers for microbial fuel cell cathodes

    KAUST Repository

    Watson, Valerie J.

    2011-03-01

    Membrane separators reduce oxygen flux from the cathode into the anolyte in microbial fuel cells (MFCs), but water accumulation and pH gradients between the separator and cathode reduces performance. Air cathodes were spray-coated (water-facing side) with anion exchange, cation exchange, and neutral polymer coatings of different thicknesses to incorporate the separator into the cathode. The anion exchange polymer coating resulted in greater power density (1167 ± 135 mW m-2) than a cation exchange coating (439 ± 2 mW m-2). This power output was similar to that produced by a Nafion-coated cathode (1114 ± 174 mW m-2), and slightly lower than the uncoated cathode (1384 ± 82 mW m-2). Thicker coatings reduced oxygen diffusion into the electrolyte and increased coulombic efficiency (CE = 56-64%) relative to an uncoated cathode (29 ± 8%), but decreased power production (255-574 mW m-2). Electrochemical characterization of the cathodes ex situ to the MFC showed that the cathodes with the lowest charge transfer resistance and the highest oxygen reduction activity produced the most power in MFC tests. The results on hydrophilic cathode separator layers revealed a trade off between power and CE. Cathodes coated with a thin coating of anion exchange polymer show promise for controlling oxygen transfer while minimally affecting power production. © 2010 Elsevier B.V. All rights reserved.

  18. Increasing input power dynamic range of SOA by shifting the transparent wavelength of tunable optical filter

    DEFF Research Database (Denmark)

    Yu, Jianjun; Jeppesen, Palle

    2001-01-01

    Gain-saturation-induced self-phase modulation (SPM) leading to pulse distortion in a semiconductor optical amplifier (SOA) is overcome by shifting a tunable optical filter (TOF). A recovered or broadened pulse can be obtained after filtering the amplified pulse in the SOA even if the short pulse...... to a longer wavelength for RZ signals and to a shorter for NRZ signals. 80-Gb/s optical time division multiplexing (OTDM) signal amplification in the SOA is demonstrated for the first time. We also demonstrate that a large IPDR for the 80-Gb/s OTDM signal can be obtained by shifting the TOF....

  19. Cathode R&D for Future Light Sources

    Energy Technology Data Exchange (ETDEWEB)

    Dowell, D.H.; /SLAC; Bazarov, I.; Dunham, B.; /Cornell U., CLASSE; Harkay, K.; /Argonne; Hernandez-Garcia; /Jefferson Lab; Legg, R.; /Wisconsin U., SRC; Padmore, H.; /LBL, Berkeley; Rao, T.; Smedley, J.; /Brookhaven; Wan, W.; /LBL, Berkeley

    2010-05-26

    This paper reviews the requirements and current status of cathodes for accelerator applications, and proposes a research and development plan for advancing cathode technology. Accelerator cathodes need to have long operational lifetimes and produce electron beams with a very low emittance. The two principal emission processes to be considered are thermionic and photoemission with the photocathodes being further subdivided into metal and semi-conductors. Field emission cathodes are not included in this analysis. The thermal emittance is derived and the formulas used to compare the various cathode materials. To date, there is no cathode which provides all the requirements needed for the proposed future light sources. Therefore a three part research plan is described to develop cathodes for these future light source applications.

  20. Design of ANSYS-based Cathode with Complex Groove

    Institute of Scientific and Technical Information of China (English)

    范植坚; 赵刚刚; 张丽娟

    2012-01-01

    The profile of cathode with complex groove needs to be modified time after time during design of electrochemical machining (ECM) cathode.A design scheme using finite element method (FEM) for cathode with complex profile is put forward to shorten the period of cathode design.Based on Laplace equation,the potential distribution on parameter-transformation model was calculated by using ANSYS,which is compared to the potential distribution calculated by substituting conductivity and current efficiency into Laplace equation.According to the difference between the results calculated and simulated by ANSYS,the cathode profile was modified by adjusting the cathode boundary.The experiments show that the dimensions and shape of workpiece machined by numerically simulated cathode conform well with the blueprint.

  1. Virtual cathode microwave generator having annular anode slit

    Science.gov (United States)

    Kwan, Thomas J. T.; Snell, Charles M.

    1988-01-01

    A microwave generator is provided for generating microwaves substantially from virtual cathode oscillation. Electrons are emitted from a cathode and accelerated to an anode which is spaced apart from the cathode. The anode has an annular slit therethrough effective to form the virtual cathode. The anode is at least one range thickness relative to electrons reflecting from the virtual cathode. A magnet is provided to produce an optimum magnetic field having the field strength effective to form an annular beam from the emitted electrons in substantial alignment with the annular anode slit. The magnetic field, however, does permit the reflected electrons to axially diverge from the annular beam. The reflected electrons are absorbed by the anode in returning to the real cathode, such that substantially no reflexing electrons occur. The resulting microwaves are produced with a single dominant mode and are substantially monochromatic relative to conventional virtual cathode microwave generators.

  2. A new shunt DC active filter of power supply in a steady high magnetic field facility

    Institute of Scientific and Technical Information of China (English)

    WANG Lei; LIU Xiao-Ning; WANG Can

    2011-01-01

    A DC active power filter is an indispensable part in a high power and high stability power supply system, especially in the power supply system of the Steady High Magnetic Field Facility, which requires that the current ripple should be limited to 50 parts per million. In view of the disadvantages of the series DC active power filter and shunt Pulse Width Modulation DC active filter, this paper puts forward a novel DC active filter by combining the advantages of the transistor regulator and the shunt type. The structure and principle of the new shunt linear active filter are introduced. Meanwhile, the design of several key components that construct the new shunt linear active filter is also analyzed. The simulation model and an experimental prototype of the shunt linear active filter are developed, and the results verify that the parameter design is reasonable and the shunt active filter has a good filter effect.

  3. Generic Kalman Filter Software

    Science.gov (United States)

    Lisano, Michael E., II; Crues, Edwin Z.

    2005-01-01

    The Generic Kalman Filter (GKF) software provides a standard basis for the development of application-specific Kalman-filter programs. Historically, Kalman filters have been implemented by customized programs that must be written, coded, and debugged anew for each unique application, then tested and tuned with simulated or actual measurement data. Total development times for typical Kalman-filter application programs have ranged from months to weeks. The GKF software can simplify the development process and reduce the development time by eliminating the need to re-create the fundamental implementation of the Kalman filter for each new application. The GKF software is written in the ANSI C programming language. It contains a generic Kalman-filter-development directory that, in turn, contains a code for a generic Kalman filter function; more specifically, it contains a generically designed and generically coded implementation of linear, linearized, and extended Kalman filtering algorithms, including algorithms for state- and covariance-update and -propagation functions. The mathematical theory that underlies the algorithms is well known and has been reported extensively in the open technical literature. Also contained in the directory are a header file that defines generic Kalman-filter data structures and prototype functions and template versions of application-specific subfunction and calling navigation/estimation routine code and headers. Once the user has provided a calling routine and the required application-specific subfunctions, the application-specific Kalman-filter software can be compiled and executed immediately. During execution, the generic Kalman-filter function is called from a higher-level navigation or estimation routine that preprocesses measurement data and post-processes output data. The generic Kalman-filter function uses the aforementioned data structures and five implementation- specific subfunctions, which have been developed by the user on

  4. Concentric Split Flow Filter

    Science.gov (United States)

    Stapleton, Thomas J. (Inventor)

    2015-01-01

    A concentric split flow filter may be configured to remove odor and/or bacteria from pumped air used to collect urine and fecal waste products. For instance, filter may be designed to effectively fill the volume that was previously considered wasted surrounding the transport tube of a waste management system. The concentric split flow filter may be configured to split the air flow, with substantially half of the air flow to be treated traveling through a first bed of filter media and substantially the other half of the air flow to be treated traveling through the second bed of filter media. This split flow design reduces the air velocity by 50%. In this way, the pressure drop of filter may be reduced by as much as a factor of 4 as compare to the conventional design.

  5. Crux vena cava filter.

    Science.gov (United States)

    Murphy, Erin H; Johnson, Eric D; Kopchok, George E; Fogarty, Thomas J; Arko, Frank R

    2009-09-01

    Inferior vena cava filters are widely accepted for pulmonary embolic prophylaxis in high-risk patients with contraindications to anticoagulation. While long-term complications have been associated with permanent filters, retrievable filters are now available and have resulted in the rapid expansion of this technology. Nonetheless, complications are still reported with optional filters. Furthermore, device tilting and thrombus load may prevent retrieval in up to 30% of patients, thereby eliminating the benefits of this technology. The Crux vena cava filter is a novel, self-centering, low-profile filter that is designed for ease of delivery, retrievability and improved efficacy while limiting fatigue-related device complications. This device has been proven safe and user-friendly in an ovine model and has recently been implanted in human subjects.

  6. CrowdFilter

    DEFF Research Database (Denmark)

    Mortensen, Michael Lind; Wallace, Byron C.; Kraska, Tim

    for complex multi-criteria search problems through crowdsourcing. The CrowdFilter system is capable of supporting both criteria-level labels and n-gram rationales, capturing the human decision making process behind each filtering choice. Using the data provided through CrowdFilter we also introduce a novel......Multi-criteria filtering of mixed open/closed-world data is a time-consuming task, requiring significant manual effort when latent open-world attributes are present. In this work we introduce a novel open-world filtering framework CrowdFilter, enabling automatic UI generation and label elicitation...... multi-criteria active learning method; capable of incorporating labels and n-gram rationales per inclusion criteria, and thus capable of determining both clear includes/excludes, as well as complex borderline cases. By incorporating the active learning approach into the elicitation process of Crowd...

  7. Conservative Noise Filters

    Directory of Open Access Journals (Sweden)

    Mona M.Jamjoom

    2016-05-01

    Full Text Available Noisy training data have a huge negative impact on machine learning algorithms. Noise-filtering algorithms have been proposed to eliminate such noisy instances. In this work, we empirically show that the most popular noise-filtering algorithms have a large False Positive (FP error rate. In other words, these noise filters mistakenly identify genuine instances as outliers and eliminate them. Therefore, we propose more conservative outlier identification criteria that improve the FP error rate and, thus, the performance of the noise filters. With the new filter, an instance is eliminated if and only if it is misclassified by a mutual decision of Naïve Bayesian (NB classifier and the original filtering criteria being used. The number of genuine instances that are incorrectly eliminated is reduced as a result, thereby improving the classification accuracy.

  8. Erosion behaviour of composite Al-Cr cathodes in cathodic arc plasmas in inert and reactive atmospheres

    CERN Document Server

    Franz, Robert; Hawranek, Gerhard; Polcik, Peter

    2015-01-01

    Al$_{x}$Cr$_{1-x}$ composite cathodes with Al contents of x = 0.75, 0.5 and 0.25 were exposed to cathodic arc plasmas in Ar, N$_2$ and O$_2$ atmospheres and their erosion behaviour was studied. Cross-sectional analysis of the elemental distribution of the near-surface zone in the cathodes by scanning electron microscopy revealed the formation of a modified layer for all cathodes and atmospheres. Due to intermixing of Al and Cr in the heat-affected zone, intermetallic Al-Cr phases formed as evidenced by X-ray diffraction analysis. Cathode poisoning effects in the reactive N$_2$ and O$_2$ atmospheres were non-uniform as a result of the applied magnetic field configuration. With the exception of oxide islands on Al-rich cathodes, reactive layers were absent in the circular erosion zone, while nitrides and oxides formed in the less eroded centre region of the cathodes.

  9. Oriented Fiber Filter Media

    Directory of Open Access Journals (Sweden)

    R. Bharadwaj

    2008-06-01

    Full Text Available Coalescing filters are widely used throughout industry and improved performance will reduce droplet emissions and operating costs. Experimental observations show orientation of micro fibers in filter media effect the permeability and the separation efficiency of the filter media. In this work two methods are used to align the fibers to alter the filter structure. The results show that axially aligned fiber media improve quality factor on the order of 20% and cutting media on an angle from a thick layered media can improve performance by about 40%. The results also show the improved performance is not monotonically correlated to the average fiber angle of the medium.

  10. Fundamentals of Stochastic Filtering

    CERN Document Server

    Crisan, Dan

    2008-01-01

    The objective of stochastic filtering is to determine the best estimate for the state of a stochastic dynamical system from partial observations. The solution of this problem in the linear case is the well known Kalman-Bucy filter which has found widespread practical application. The purpose of this book is to provide a rigorous mathematical treatment of the non-linear stochastic filtering problem using modern methods. Particular emphasis is placed on the theoretical analysis of numerical methods for the solution of the filtering problem via particle methods. The book should provide sufficient

  11. Neutral beam dump with cathodic arc titanium gettering.

    Science.gov (United States)

    Smirnov, A; Krivenko, A S; Murakhtin, S V; Savkin, V Ya; Korepanov, S A; Putvinski, S

    2011-03-01

    An incomplete neutral beam capture can degrade the plasma performance in neutral beam driven plasma machines. The beam dumps mitigating the shine-through beam recycling must entrap and retain large particle loads while maintaining the beam-exposed surfaces clean of the residual impurities. The cathodic arc gettering, which provides high evaporation rate coupled with a fast time response, is a powerful and versatile technique for depositing clean getter films in vacuum. A compact neutral beam dump utilizing the titanium arc gettering was developed for a field-reversed configuration plasma sustained by 1 MW, 20-40 keV neutral hydrogen beams. The titanium evaporator features a new improved design. The beam dump is capable of handling large pulsed gas loads, has a high sorption capacity, and is robust and reliable. With the beam particle flux density of 5 × 10(17) H∕(cm(2) s) sustained for 3-10 ms, the beam recycling coefficient, defined as twice the ratio of the hydrogen molecular flux leaving the beam dump to the incident flux of high-energy neutral atoms, is ∼0.7. The use of the beam dump allows us to significantly reduce the recycling of the shine-through neutral beam as well as to improve the vacuum conditions in the machine.

  12. Filter holder and gasket assembly for candle or tube filters

    Science.gov (United States)

    Lippert, Thomas Edwin; Alvin, Mary Anne; Bruck, Gerald Joseph; Smeltzer, Eugene E.

    1999-03-02

    A filter holder and gasket assembly for holding a candle filter element within a hot gas cleanup system pressure vessel. The filter holder and gasket assembly includes a filter housing, an annular spacer ring securely attached within the filter housing, a gasket sock, a top gasket, a middle gasket and a cast nut.

  13. Small-size plasma diode with a transparent internal cathode for neutron generation

    Science.gov (United States)

    Shikanov, A. E.; Vovchenko, E. D.; Kozlovskii, K. I.; Shatokhin, V. L.

    2015-01-01

    A discharge plasma system for neutron generation based on the concept of inertial electrostatic confinement is considered. The system is made in the form of a gas-filled (1-60 Pa) diode with a composite hollow cathode placed at its center symmetrically to an embracing hollow cylindrical anode. Preionization of the discharge gap and an original design of the electrode system with a transparent central part make it possible to initiate a pulse high-voltage (100-150 kV) volume discharge in the ion oscillation mode. Estimates of the neutron emission in such a deuterium-filled diode show the feasibility of generating a pulse with a neutron yield on the order of 105 in the reaction D( d, n)3He, which is confirmed in experiments with an optimized geometry of the electrodes.

  14. High power microwave generation using a repetitive electron gun with a ferroelectric cathode

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, Y.; Ivers, J.D.; Nation, J.A.; Wang, P. Golkowski, C.; Flechtner, D.; Schaechter, L.

    1999-07-01

    An electron gun using a ferroelectric cathode driven by a ferrite core transformer-pulse line system produces a 500kV, 50--200A, 250ns long beam. The beam is used to drive an X-band amplifier. The amplifier consists of a single stage disk loaded type structure. At the end of the amplifier, a coaxial mode converter is used to decouple the beam from the microwave radiation. The amplifier operates at a repetition rate of 0.1Hz. The beam emission is controlled by a voltage pulse applied to the back of the ferroelectric. Results will be reported on the amplifier performance characteristics with a 50A beam and the results compared with simulation data. An improved gun design, which gives a uniform cross section 200A beam is being built, and early results obtained, using the high current gun, will also be presented.

  15. Beam dynamics in a long-pulse linear induction accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Ekdahl, Carl [Los Alamos National Laboratory; Abeyta, Epifanio O [Los Alamos National Laboratory; Aragon, Paul [Los Alamos National Laboratory; Archuleta, Rita [Los Alamos National Laboratory; Cook, Gerald [Los Alamos National Laboratory; Dalmas, Dale [Los Alamos National Laboratory; Esquibel, Kevin [Los Alamos National Laboratory; Gallegos, Robert A [Los Alamos National Laboratory; Garnett, Robert [Los Alamos National Laboratory; Harrison, James F [Los Alamos National Laboratory; Johnson, Jeffrey B [Los Alamos National Laboratory; Jacquez, Edward B [Los Alamos National Laboratory; Mc Cuistian, Brian T [Los Alamos National Laboratory; Montoya, Nicholas A [Los Alamos National Laboratory; Nath, Subrato [Los Alamos National Laboratory; Nielsen, Kurt [Los Alamos National Laboratory; Oro, David [Los Alamos National Laboratory; Prichard, Benjamin [Los Alamos National Laboratory; Rose, Chris R [Los Alamos National Laboratory; Sanchez, Manolito [Los Alamos National Laboratory; Schauer, Martin M [Los Alamos National Laboratory; Seitz, Gerald [Los Alamos National Laboratory; Schulze, Martin [Los Alamos National Laboratory; Bender, Howard A [Los Alamos National Laboratory; Broste, William B [Los Alamos National Laboratory; Carlson, Carl A [Los Alamos National Laboratory; Frayer, Daniel K [Los Alamos National Laboratory; Johnson, Douglas E [Los Alamos National Laboratory; Tom, C Y [Los Alamos National Laboratory; Trainham, C [Los Alamos National Laboratory; Williams, John [Los Alamos National Laboratory; Scarpetti, Raymond [LLNL; Genoni, Thomas [VOSS; Hughes, Thomas [VOSS; Toma, Carsten [VOSS

    2010-01-01

    The second axis of the Dual Axis Radiography of Hydrodynamic Testing (DARHT) facility produces up to four radiographs within an interval of 1.6 microseconds. It accomplishes this by slicing four micro-pulses out of a long 1.8-kA, 16.5-MeV electron beam pulse and focusing them onto a bremsstrahlung converter target. The long beam pulse is created by a dispenser cathode diode and accelerated by the unique DARHT Axis-II linear induction accelerator (LIA). Beam motion in the accelerator would be a problem for radiography. High frequency motion, such as from beam breakup instability, would blur the individual spots. Low frequency motion, such as produced by pulsed power variation, would produce spot to spot differences. In this article, we describe these sources of beam motion, and the measures we have taken to minimize it.

  16. A digital matched filter for reverse time chaos

    Energy Technology Data Exchange (ETDEWEB)

    Bailey, J. Phillip, E-mail: mchamilton@auburn.edu; Beal, Aubrey N.; Dean, Robert N.; Hamilton, Michael C. [Electrical and Computer Engineering Department, Auburn University, Auburn, Alabama 36489 (United States)

    2016-07-15

    The use of reverse time chaos allows the realization of hardware chaotic systems that can operate at speeds equivalent to existing state of the art while requiring significantly less complex circuitry. Matched filter decoding is possible for the reverse time system since it exhibits a closed form solution formed partially by a linear basis pulse. Coefficients have been calculated and are used to realize the matched filter digitally as a finite impulse response filter. Numerical simulations confirm that this correctly implements a matched filter that can be used for detection of the chaotic signal. In addition, the direct form of the filter has been implemented in hardware description language and demonstrates performance in agreement with numerical results.

  17. Plasma Cathode for E-Beam Lasers

    Science.gov (United States)

    1975-08-01

    JMJIIJUillWWpi^WiffW^HipaHIP’Pi1’’’ "a" ii.lllVi;lM’iiWMlMBfj!|l|>WiiU|’lUW"L’l’w«|M>l|Wy™.^J"^^y-ff^w», iitM ^^^ The 4 cm x 40 cm plasma cathode e-gun, which is

  18. The Hollow Cathode Phase of Pseudospark Operation

    Science.gov (United States)

    1993-06-01

    THE HOLLOW CATHODE PHASE OF PSEUDOSPARK OPERATION L. Pitchford and J. P. Boeuf University Paul Sabatier, France V. Puech University De Paris-Sud...ORGANIZATION NAME(S) AND ADDRESS(ES) University Paul Sabatier, France 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME...Appl. Phys. 53, 1699 (1988). [9] A. Anders, S. Anders, and M. Gundersen, submitted to Phys. Rev. Lett. [10] J. P. Boeuf and L. Pitchford , IEEE

  19. Cathodic Cage Plasma Nitriding: An Innovative Technique

    OpenAIRE

    Sousa,R.R.M.; de Araújo, F. O.; J. A. P. da Costa; Brandim,A.S.; R. A. de Brito; C. Alves

    2012-01-01

    Cylindrical samples of AISI 1020, AISI 316, and AISI 420 steels, with different heights, were simultaneously treated by a new technique of ionic nitriding, entitled cathodic cage plasma nitriding (CCPN), in order to evaluate the efficiency of this technique to produce nitrided layers with better properties compared with those obtained using conventional ionic nitriding technique. This method is able to eliminate the edge effect in the samples, promoting a better uniformity of temperature, and...

  20. FUZZY LOGIC CONTROLLED CATHODIC PROTECTION CIRCUIT DESIGN

    OpenAIRE

    AKÇAYOL, M. Ali

    2010-01-01

    In this study, output voltage of automatic transformer-rectifier (TR) unit of impressed current cathodic protection has been controlled by using fuzzy logic controller. To prevent corrosion, voltage between the protection metal and the auxiliary anode has to be controlled on a desired level. Because soil resistance in the environment changes with humidity and soil characteristics, TRs must control the output voltage between protection metal and auxiliary anode automatically. In this study, a ...

  1. Modeling lithium/hybrid-cathode batteries

    Energy Technology Data Exchange (ETDEWEB)

    Gomadam, Parthasarathy M.; Merritt, Don R.; Scott, Erik R.; Schmidt, Craig L.; Skarstad, Paul M. [Medtronic Energy and Component Center, 6700 Shingle Creek Pkwy, Brooklyn Center, MN 55430 (United States); Weidner, John W. [Center for Electrochemical Engineering, Department of Chemical Engineering, University of South Carolina, Columbia, SC 29208 (United States)

    2007-12-06

    This document describes a first-principles-based mathematical model developed to predict the voltage-capacity behavior of batteries having hybrid cathodes comprising a mixture of carbon monofluoride (CF{sub x}) and silver vanadium oxide (SVO). These batteries typically operate at moderate rates of discharge, lasting several years. The model presented here is an accurate tool for design optimization and performance prediction of batteries under current drains that encompass both the application rate and accelerated testing. (author)

  2. A definitive criterion for cathodic protection

    Energy Technology Data Exchange (ETDEWEB)

    Alexander, Roger [Cathodic Protection Network International Ltd., Reading (United Kingdom)

    2009-07-01

    The corrosion reaction is defined using the Pourbaix Diagram and includes consideration of the pH, temperature, pressure, nobility of the metal and conductivity of the electrolyte. The passive zone can be established in a laboratory by creating a closed circuit condition in which the voltages can be measured. Natural corrosion cells occurring in simple conditions can be evaluated for the purpose of monitoring the performance of cathodic protection. Metal pipelines are complex networks of conductors submerged in electrolyte of infinitely variable qualities. The present method used to ascertain the effectiveness of cathodic protection has many inherent errors and results in costly and unpredictable corrosion failures. An electrode has been devised to define the exact electrical status of the corrosion reaction at its location. The design allows a closed circuit measurement of the corrosion current that can determine whether or not corrosion has been stopped by cathodic protection. This has allowed the development of software that can calculate the condition and corrosion status throughout a network of pipelines, using electrical circuit analysis common in the electronics industry. (author)

  3. Assessment and evaluation of ceramic filter cleaning techniques: Task Order 19

    Energy Technology Data Exchange (ETDEWEB)

    Chen, H.; Zaharchuk, R.; Harbaugh, L.B.; Klett, M.

    1994-10-01

    The objective of this study was to assess and evaluate the effectiveness, appropriateness and economics of ceramic barrier filter cleaning techniques used for high-temperature and high-pressure particulate filtration. Three potential filter cleaning techniques were evaluated. These techniques include, conventional on-line pulse driven reverse gas filter cleaning, off-line reverse gas filter cleaning and a novel rapid pulse driven filter cleaning. These three ceramic filter cleaning techniques are either presently employed, or being considered for use, in the filtration of coal derived gas streams (combustion or gasification) under high-temperature high-pressure conditions. This study was divided into six subtasks: first principle analysis of ceramic barrier filter cleaning mechanisms; operational values for parameters identified with the filter cleaning mechanisms; evaluation and identification of potential ceramic filter cleaning techniques; development of conceptual designs for ceramic barrier filter systems and ceramic barrier filter cleaning systems for two DOE specified power plants; evaluation of ceramic barrier filter system cleaning techniques; and final report and presentation. Within individual sections of this report critical design and operational issues were evaluated and key findings were identified.

  4. Excimer Laser Pulse Compress With Pulse Feedback

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>To attain a shorter laser pulse, a compressing technique called pulse feedback was developed from the saturation gain switch applied to the amplification in a discharge pumping excimer laser cavity. It can

  5. Fast Anisotropic Gauss Filtering

    NARCIS (Netherlands)

    Geusebroek, J.M.; Smeulders, A.W.M.; van de Weijer, J.; Heyden, A.; Sparr, G.; Nielsen, M.; Johansen, P.

    2002-01-01

    We derive the decomposition of the anisotropic Gaussian in a one dimensional Gauss filter in the x-direction followed by a one dimensional filter in a non-orthogonal direction phi. So also the anisotropic Gaussian can be decomposed by dimension. This appears to be extremely efficient from a computin

  6. Multilevel ensemble Kalman filter

    KAUST Repository

    Chernov, Alexey

    2016-01-06

    This work embeds a multilevel Monte Carlo (MLMC) sampling strategy into the Monte Carlo step of the ensemble Kalman filter (EnKF). In terms of computational cost vs. approximation error the asymptotic performance of the multilevel ensemble Kalman filter (MLEnKF) is superior to the EnKF s.

  7. Updating the OMERACT filter

    DEFF Research Database (Denmark)

    Wells, George; Beaton, Dorcas E; Tugwell, Peter;

    2014-01-01

    The "Discrimination" part of the OMERACT Filter asks whether a measure discriminates between situations that are of interest. "Feasibility" in the OMERACT Filter encompasses the practical considerations of using an instrument, including its ease of use, time to complete, monetary costs, and inter...

  8. Vena cava filter; Vena-cava-Filter

    Energy Technology Data Exchange (ETDEWEB)

    Helmberger, T. [Klinikum Bogenhausen, Institut fuer Diagnostische und Interventionelle Radiologie und Nuklearmedizin, Muenchen (Germany)

    2007-05-15

    Fulminant pulmonary embolism is one of the major causes of death in the Western World. In most cases, deep leg and pelvic venous thrombosis are the cause. If an anticoagulant/thrombotic therapy is no longer possible or ineffective, a vena cava filter implant may be indicated if an embolism is threatening. Implantation of the filter is a simple and safe intervention. Nevertheless, it is necessary to take into consideration that the data base for determining the indications for this treatment are very limited. Currently, a reduction in the risk of thromboembolism with the use of filters of about 30%, of recurrences of almost 5% and fatal pulmonary embolism of 1% has been reported, with a risk of up to 20% of filter induced vena cava thrombosis. (orig.) [German] Die fulminante Lungenembolie zaehlt zu den Haupttodesursachen in der westlichen Welt. In der Mehrzahl der Faelle sind tiefe Bein- und Beckenvenenthrombosen ursaechlich verantwortlich. Ist eine antikoagulative/-thrombotische Therapie nicht (mehr) moeglich oder unwirksam, kann bei drohender Emboliegefahr die Vena-cava-Filterimplantation indiziert sein. Die Filterimplantation ist eine einfache und sehr sichere Intervention. Dennoch muss bei der Indikationsstellung beruecksichtigt werden, dass die Datenlage zur Wirksamkeit sehr limitiert ist. So wird aktuell ueber eine Reduktion des Thrombembolierisikos um 30% bei Embolierezidiven von knapp 5% und fatalen Lungenembolien von 1% unter Filterprophylaxe berichtet, bei einem Risiko von bis zu 20% fuer die filterinduzierte Vena-cava-Thrombose. (orig.)

  9. Cathode power distribution system and method of using the same for power distribution

    Science.gov (United States)

    Williamson, Mark A; Wiedmeyer, Stanley G; Koehl, Eugene R; Bailey, James L; Willit, James L; Barnes, Laurel A; Blaskovitz, Robert J

    2014-11-11

    Embodiments include a cathode power distribution system and/or method of using the same for power distribution. The cathode power distribution system includes a plurality of cathode assemblies. Each cathode assembly of the plurality of cathode assemblies includes a plurality of cathode rods. The system also includes a plurality of bus bars configured to distribute current to each of the plurality of cathode assemblies. The plurality of bus bars include a first bus bar configured to distribute the current to first ends of the plurality of cathode assemblies and a second bus bar configured to distribute the current to second ends of the plurality of cathode assemblies.

  10. Effect of paraelectrode processes on contraction of space charge in periodic-pulse lasers

    Science.gov (United States)

    Arytyunyan, R. V.; Baranov, V. Yu.; Borisov, V. M.; Vinokhodov, A. Yu.; Kiryukhin, Yu. B.

    1986-05-01

    A characteristic feature of periodic-pulse electric-discharge CO2-lasers and excimer lasers is contraction of the space charge as the pulse repetition rate increases. The emission energy per pulse decreases as a consequence, with the average laser power first ceasing to increase linearly beyond a certain corner repetition rate and then decreasing beyond a certain critical repetition rate. A study of this phenomenon was made, for the purpose of separating the effect of paracathode processes from the effect of gas dynamics and then evaluating the effect of the former alone. Paraelectrode perturbations were simulated by focusing the radiation from the an XeCl-laser on the cathode surface in an atmosphere of nonabsorbing gases. Laser pulses of up to approximately 0.5 J energy and of approximately 50 ns duration were focused within a spot of 1 mm(2) area on a cathode inside a discharge chamber, with the power density of incident radiation regulated by means of an attenuator. A space charge within a volume of 2.5x4.5x9 cm(3) was generated between this specially shaped cathode and a mesh anode with an approximately 50% optical transmission coefficient. The space charge in helium and in neon was photographed, and the time lag of a discharge pulse behind a contracting laser pulse was measured as a function of the laser pulse energy for these two gases, as well as for a He+C12 gas mixture. The general trend was found to be the same in each case, the time lag increasing with increasing energy first at a slower rate up to a critical energy level and then faster. It has been established that plasma does not build up on the cathode before the laser pulse energy reaches 30 mJ (for a 3 mm(2) surface area), while plasma glow begins as the laser pulse energy reaches 150 mJ. A contracted channel begins to form within the laser-cathode interaction space, with an attendant fast increase of the time lag owing to evaporation of the cathode metal.

  11. Temporal characteristics of narrow-band optical filters and their application in lidar systems.

    Science.gov (United States)

    Yang, G; Billmers, R; Herczfeld, P R; Contarino, V M

    1997-03-15

    The temporal characteristics of two different narrow-band optical filters at 532 nm are reported. Both filters operate on the 4P(1/2) - 8S(1/2) atomic transition of potassium vapor, where the 4P(1/2) state is excited by a 770-nm, 10-ns laser pulse. The filters operate on the principle of circular birefringence induced by either the Faraday effect or two-photon transition, which is confirmed by experiments. The characteristic decay times of the filters are 5 and 0.015 mus, which is significant for the design of optical gating and signal processing with matched filters for ocean lidar.

  12. Effect of cathode model on arc attachment for short high-intensity arc on a refractory cathode

    Science.gov (United States)

    Javidi Shirvan, Alireza; Choquet, Isabelle; Nilsson, Håkan

    2016-12-01

    Various models coupling the refractory cathode, the cathode sheath and the arc at atmospheric pressure exist. They assume a homogeneous cathode with a uniform physical state, and differ by the cathode layer and the plasma arc model. However even the most advanced of these models still fail in predicting the extent of the arc attachment when applied to short high-intensity arcs such as gas tungsten arcs. Cathodes operating in these conditions present a non-uniform physical state. A model taking into account the first level of this non-homogeneity is proposed based on physical criteria. Calculations are done for 5 mm argon arcs with a thoriated tungsten cathode. The results obtained show that radiative heating and cooling of the cathode surface are of the same order. They also show that cathode inhomogeneity has a significant effect on the arc attachment, the arc temperature and pressure. When changing the arc current (100 A, 200 A) the proposed model allows predicting trends observed experimentally that cannot be captured by the homogeneous cathode model unless restricting a priori the size of the arc attachment. The cathode physics is thus an important element to include to obtain a comprehensive and predictive arc model.

  13. Weighted guided image filtering.

    Science.gov (United States)

    Li, Zhengguo; Zheng, Jinghong; Zhu, Zijian; Yao, Wei; Wu, Shiqian

    2015-01-01

    It is known that local filtering-based edge preserving smoothing techniques suffer from halo artifacts. In this paper, a weighted guided image filter (WGIF) is introduced by incorporating an edge-aware weighting into an existing guided image filter (GIF) to address the problem. The WGIF inherits advantages of both global and local smoothing filters in the sense that: 1) the complexity of the WGIF is O(N) for an image with N pixels, which is same as the GIF and 2) the WGIF can avoid halo artifacts like the existing global smoothing filters. The WGIF is applied for single image detail enhancement, single image haze removal, and fusion of differently exposed images. Experimental results show that the resultant algorithms produce images with better visual quality and at the same time halo artifacts can be reduced/avoided from appearing in the final images with negligible increment on running times.

  14. Robustifying Vector Median Filter

    Directory of Open Access Journals (Sweden)

    Valentín Gregori

    2011-08-01

    Full Text Available This paper describes two methods for impulse noise reduction in colour images that outperform the vector median filter from the noise reduction capability point of view. Both methods work by determining first the vector median in a given filtering window. Then, the use of complimentary information from componentwise analysis allows to build robust outputs from more reliable components. The correlation among the colour channels is taken into account in the processing and, as a result, a more robust filter able to process colour images without introducing colour artifacts is obtained. Experimental results show that the images filtered with the proposed method contain less noisy pixels than those obtained through the vector median filter. Objective measures demonstrate the goodness of the achieved improvement.

  15. Filter cake breaker systems

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, Marcelo H.F. [Poland Quimica Ltda., Duque de Caxias, RJ (Brazil)

    2004-07-01

    Drilling fluids filter cakes are based on a combination of properly graded dispersed particles and polysaccharide polymers. High efficiency filter cakes are formed by these combination , and their formation on wellbore walls during the drilling process has, among other roles, the task of protecting the formation from instantaneous or accumulative invasion of drilling fluid filtrate, granting stability to well and production zones. Filter cake minimizes contact between drilling fluid filtrate and water, hydrocarbons and clay existent in formations. The uniform removal of the filter cake from the entire interval is a critical factor of the completion process. The main methods used to breaking filter cake are classified into two groups, external or internal, according to their removal mechanism. The aim of this work is the presentation of these mechanisms as well their efficiency. (author)

  16. Naive Bayesian for Email Filtering

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The paper presents a method of email filter based on Naive Bayesian theory that can effectively filter junk mail and illegal mail. Furthermore, the keys of implementation are discussed in detail. The filtering model is obtained from training set of email. The filtering can be done without the users specification of filtering rules.

  17. Modelling cathode spots in glow discharges in the cathode boundary layer geometry

    CERN Document Server

    Almeida, P G C; Bieniek, M S

    2015-01-01

    Self-organized patterns of cathode spots in glow discharges are computed in the cathode boundary layer geometry, which is the one employed in most of the experiments reported in the literature. The model comprises conservation and transport equations of electrons and a single ion species, written in the drift-diffusion and local-field approximations, and Poisson's equation. Multiple solutions existing for the same value of the discharge current and describing modes with different configurations of cathode spots are computed by means of a stationary solver. The computed solutions are compared to their counterparts for plane-parallel electrodes, and experiments. All of the computed spot patterns have been observed in the experiment.

  18. Pulsed Optics

    Science.gov (United States)

    Hirlimann, C.

    Optics is the field of physics which comprises knowledge on the interaction between light and matter. When the superposition principle can be applied to electromagnetic waves or when the properties of matter do not depend on the intensity of light, one speaks of linear optics. This situation occurs with regular light sources such as light bulbs, low-intensity light-emitting diodes and the sun. With such low-intensity sources the reaction of matter to light can be characterized by a set of parameters such as the index of refraction, the absorption and reflection coefficients and the orientation of the medium with respect to the polarization of the light. These parameters depend only on the nature of the medium. The situation changed dramatically after the development of lasers in the early sixties, which allowed the generation of light intensities larger than a kilowatt per square centimeter. Actual large-scale short-pulse lasers can generate peak powers in the petawatt regime. In that large-intensity regime the optical parameters of a material become functions of the intensity of the impinging light. In 1818 Fresnel wrote a letter to the French Academy of Sciences in which he noted that the proportionality between the vibration of the light and the subsequent vibration of matter was only true because no high intensities were available. The intensity dependence of the material response is what usually defines nonlinear optics.

  19. Cathode including a non fluorinated linear chain polymer as the binder, method of making the cathode, and lithium electrochemical cell containing the cathode

    Science.gov (United States)

    Plichta, Edward J.; Salomon, Mark

    1986-08-01

    A cathode suitable for use in a lithium electrochemical cell is made from a mixture of active cathode material, carbon, and non fluorinated linear chain polymer by a method including the following steps: (1) dissolving the non fluorinated linear polymer in a non polar solvent at a temperature near the melting point of the polymer; (2) adding the active cathode material and carbon and evaporating the solvent; and (3) grinding the dried mixture into a fine powder and making it into a cathode by pressing the powdered mixture onto both sides of an expanded metal screen and then cutting to the desired dimensions. The cathode can be combined with lithium as the anode and a solution of 0.8 mol/cu dm LiAlCl4 in a mixed organic solvent of 24 mass percent 4-butyrolactone in 1, 2 dimethoxyethane as the electrolyte to provide a mechanically stable, relatively inexpensive lithium electrochemical cell having good cell performance.

  20. Cathodic micro-arc electrodeposition of yttrium stabilized zirconia (YSZ) coatings on FeCrAl alloy

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The formation of ceramic coatings on metal substrate by cathodic electrolytic deposition (CELD) has received more attention in recent years. But only thin films can be prepared via CELD. Yttrium stabilized zirconia (YSZ) ceramic coatings were deposited on FeCrAl alloy by a novel technique--cathodic micro-arc electrodeposition (CMED). The result shows that, when a high pulse electric field is applied to the cathode which was pre-deposited with a thin YSZ film, dielectric breakdown occurs and micro-arc discharges appear. Coatings with reasonably thickness of ~300μm and crystalline structure can be deposited on the cathode by utilizing the energy of the micro-arc. The thickness of the as-deposited coating is dominated by the voltage and the frequency. Y2O3 is co-deposited with ZrO2 when Y(NO3)3 was added to the electrolyte, which stabilize t-phase, t′- phase and c-phase of ZrO2 at room temperature. The amount of the m-ZrO2 in the coating is diminished by increasing the concentration of Y(NO3)3 in the electrolyte. This report describes the processing of CMED and studies the microstructure of the deposited YSZ coatings.

  1. High Power Experiment of X-Band Thermionic Cathode RF Gun for Compton Scattering X-ray Source

    Science.gov (United States)

    Sakamoto, Fumito; Uesaka, Mitsuru; Dobashi, Katsuhiro; Yamamoto, Tomohiko; Meng, De; Urakawa, Junji; Higo, Toshiyasu; Akemoto, Mitsuo; Matsuo, Kenichi; Sakae, Hisaharu; Yamamoto, Masashi

    2006-11-01

    We are currently developing a compact monochromatic X-ray source based on laser-electron collision. To realize remarkably compact-, high-intensity- and highly-stable-system, we adopt an X-band multi-bunch liner accelerator (linac) and reliable Q-switch laser. The X-ray yields by the multi-bunch electron beam and Q-switch Nd: YAG laser of 1.4 J/10 ns (FWHM) (532 nm, second harmonic) is 107 photons/RF-pulse (108 photons/sec for 10 Hz operation). The injector of the system consists of a 3.5-cell X-band thermionic cathode RF gun and an alpha magnet. So far we have achieved beam generation from the X-band thermionic cathode RF gun. The peak beam energy is 2 MeV. This experimental high energy (˜2 MeV) beam generation from the X-band thermionic cathode RF gun is the first in the world. In this paper, we describe the system of the Compton scattering X-ray source based on the X-band linac, experimental results of X-band thermionic cathode RF gun and the details of the experimental setup for Compton scattering X-ray generation that are under construction.

  2. Rf Gun with High-Current Density Field Emission Cathode

    Energy Technology Data Exchange (ETDEWEB)

    Jay L. Hirshfield

    2005-12-19

    High current-density field emission from an array of carbon nanotubes, with field-emission-transistor control, and with secondary electron channel multiplication in a ceramic facing structure, have been combined in a cold cathode for rf guns and diode guns. Electrodynamic and space-charge flow simulations were conducted to specify the cathode configuration and range of emission current density from the field emission cold cathode. Design of this cathode has been made for installation and testing in an existing S-band 2-1/2 cell rf gun. With emission control and modulation, and with current density in the range of 0.1-1 kA/cm2, this cathode could provide performance and long-life not enjoyed by other currently-available cathodes

  3. Assistant Anode in a Cathodic Arc Plasma Source

    Institute of Scientific and Technical Information of China (English)

    张涛; Paul K. Chu; 张荟星; Ian G. Brown

    2001-01-01

    The performance and characteristics of a cathodic arc plasma source, consisting of a titanium cathode, an anode with and without a tungsten mesh, and a coil producing a focusing magnetic field between the anode and cathode,are investigated. The high transparency and large area of the mesh allow a high plasma flux to penetrate the anode from the cathodic arc. The mesh helps to decrease the arc resistance and the ignition voltage of the cathodic arc in the focusing magnetic field, and to increase the life of the source, which means that the source makes the cathodic arc easily and greatly stabilized during the operation when a focusing magnetic field exists in the source.

  4. Cathodic electrocatalyst layer for electrochemical generation of hydrogen peroxide

    Science.gov (United States)

    Rhodes, Christopher P. (Inventor); Tennakoon, Charles L. K. (Inventor); Singh, Waheguru Pal (Inventor); Anderson, Kelvin C. (Inventor)

    2011-01-01

    A cathodic gas diffusion electrode for the electrochemical production of aqueous hydrogen peroxide solutions. The cathodic gas diffusion electrode comprises an electrically conductive gas diffusion substrate and a cathodic electrocatalyst layer supported on the gas diffusion substrate. A novel cathodic electrocatalyst layer comprises a cathodic electrocatalyst, a substantially water-insoluble quaternary ammonium compound, a fluorocarbon polymer hydrophobic agent and binder, and a perfluoronated sulphonic acid polymer. An electrochemical cell using the novel cathodic electrocatalyst layer has been shown to produce an aqueous solution having between 8 and 14 weight percent hydrogen peroxide. Furthermore, such electrochemical cells have shown stable production of hydrogen peroxide solutions over 1000 hours of operation including numerous system shutdowns.

  5. Cathodic phosphate coating containing nano zinc particles on magnesium alloy

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A technology for preparation of a cathodic phosphate coating mainly containing nano metallic zinc particles and phosphate compounds on magnesium alloy was developed.The influence of cathodic current density on the microstructure of the cathodic phosphate coating Was investigated.The results show that the crystals of the coating are finer and the microstructures of the outer surface of the coatings are zigzag at the cathodic density of 0.2-0.5 A/dm2.The content of nano metallic zinc particles in the coating decreases with the increase of the thickness of the coatings and tends to be zero when the coating thickness is 4.14 μm.The cathodic phosphate coating was applied to be a transition coating for improving the adhesion between the paints and the magnesium alloys.The formation mechanism of the cathodic phosphate coating was investigated as well.

  6. Effect of cathodic protection on the state of steel reinforcement

    Energy Technology Data Exchange (ETDEWEB)

    Cam, Phan Luong; Thuy, Thi Bich [Hanoi University of Technology, Hanoi (Viet Nam)

    2002-10-15

    Damage of reinforced concrete structures is mainly caused by chloride or carbonation induced corrosion of steel. Cathodic protection is a very effective measure for corrosion control of steel in concrete, especially in chloride contaminated concrete. In this paper, effect of cathodic protection on the state of steel reinforcement is presented. Cathodic polarization of reinforcements in concrete was done under different submerged conditions. Cyclic potentiodynamic tests were used to determine the effect of cathodic protection on the behavior of the steel. Pitting appeared on the non-protected steel, but was not observed on the cathodically protected steel. microscopic photographs show that a close film exists on the protected steel, while the non-protected steel's film is loose. Investigated results have proved the effect of cathodic protection in restoring or strengthening passive film on the steel reinforcement

  7. Relativistic electron beams from cathodes at 1 GV/m gradient

    Energy Technology Data Exchange (ETDEWEB)

    Srinivasan-Rao, T.; Smedley, J.; Schill, J.

    1998-05-01

    In the past decade, there has been extensive research in the development of low emittance, high brightness electron injectors for linear collider and free electron laser applications. RF injectors with a few nC charge in a few ps, with an emittance of {approximately}1--5 {pi}mm mrad are operational in a number of facilities. In these devices, a laser beam irradiates a photocathode embedded in an RF cavity. The photoelectrons released by the laser are immediately accelerated to relativistic velocities, thereby reducing the space charge effects. The frequency of the RF and the design of the cavity are chosen to minimize the RF and space charge effects on the electron bunch so that low emittance, high brightness electron beam could be generated. Minimization of RF effects on emittnce growth require a low RF frequency while minimizing the space charge effects require high field and hence high RF frequency. The design is hence a compromise between these two conflicting requirements. Some of these limitations could be overcome by using a large pulsed electric field at the cathode rather than a RF field. The duration of the pulsed field should be chosen so that it is longer than the electron bunch length and the transit time in the accelerating region, but short enough to avoid breakdown problems. Development of a high brightness electron source using this scheme requires a pulse generator, a laser pulse of sufficient energy to trigger and synchronize the electrical pulses, and a short laser pulse to irradiate the photocathode and generate electron pulses to be accelerated. The designs of these components are described.

  8. High temperature superconducting thin films for microwave filters

    Institute of Scientific and Technical Information of China (English)

    ZHAO; Xinjie(赵新杰); LI; Lin(李林); LEI; Chong(雷冲); TIAN; Ybngjun(田永军)

    2002-01-01

    YBa2Cu3O7-δ and Tl2Ba2CaCu2O8 thin films for microwave filters were synthesized by pulsed laser deposition and the two-step thalliation process. Substrate quality requirements and the relation of thin film morphology, microstructure with microwave surface resistance were discussed.

  9. Pulsed pumping of semiconductor disk lasers.

    Science.gov (United States)

    Hempler, Nils; Hopkins, John-Mark; Kemp, Alan J; Schulz, Nico; Rattunde, Marcel; Wagner, Joachim; Dawson, Martin D; Burns, David

    2007-03-19

    Efficient operation of semiconductor disk lasers is demonstrated using uncooled and inexpensive 905nm high-power pulsed semiconductor pump lasers. Laser emission, with a peak power of 1.7W, is obtained from a 2.3mum semiconductor disk laser. This is seven times the power achieved under continuous pumping. Analysis of the time-dependent spectral characteristics of the laser demonstrate that significant device heating occurs over the 100-200ns duration of the pumping pulse - finite element modelling of the thermal processes is undertaken in support of these data. Spectral narrowing to below 0.8nm is obtained by using an intra-cavity birefringent filter.

  10. New Cathode Materials for Intermediate Temperature Solid Oxide Fuel Cells

    Energy Technology Data Exchange (ETDEWEB)

    Allan J. Jacobson

    2006-09-30

    the perovskite compositions that were being investigated at PNNL, in order to assess the relative importance of the intrinsic properties such as oxygen ion diffusion and surface exchange rates as predictors of performance in cell tests. We then used these measurements to select new materials for scaled up synthesis and performance evaluation in single cell tests. The results of the single cell tests than provided feedback to the materials synthesis and selection steps. In this summary, the following studies are reported: (1) Synthesis, characterization, and DC conductivity measurements of the P1 compositions La{sub 0.8}Sr{sub 0.2}FeO{sub 3-x} and La{sub 0.7}Sr{sub 0.3}FeO{sub 3-x} were completed. A combinational approach for preparing a range P1 (La,Sr)FeO{sub 3} compositions as thin films was investigated. Synthesis and heat treatment of amorphous SrFeO{sub 3-x} and LaFeO{sub 3-x} films prepared by pulsed laser deposition are described. (2) Oxygen transport properties of K1 compositions La{sub x}Pr{sub 2-x}NiO{sub 4+d} (x =2.0, 1.9, 1.2, 1.0 and 0) measured by electrical conductivity relaxation are presented in this report. Area specific resistances determined by ac impedance measurements for La{sub 2}NiO{sub 4+{delta}} and Pr{sub 2}NiO{sub 4+{delta}} on CGO are encouraging and suggest that further optimization of the electrode microstructure will enable the target to be reached. (3) The oxygen exchange kinetics of the oxygen deficient double perovskite LnBaCo{sub 2}O{sub 5.5+{delta}} (Ln=Pr and Nd) were determined by electrical conductivity relaxation. The high electronic conductivity and rapid diffusion and surface exchange kinetics of PBCO suggest its application as cathode material in intermediate temperature solid oxide fuel cells. The first complete cell measurements were performed on Ni/CGO/CGO/PBCO/CGO cells. (4) The oxygen exchange kinetics of highly epitaxial thin films of PrBaCo{sub 2}O{sub 5.5+{delta}} (PBCO) has been determined by electrical conductivity

  11. Structured electron beams from nano-engineered cathodes

    Energy Technology Data Exchange (ETDEWEB)

    Lueangaramwong, A. [NICADD, DeKalb; Mihalcea, D. [NICADD, DeKalb; Andonian, G. [RadiaBeam Tech.; Piot, P. [Fermilab

    2017-03-07

    The ability to engineer cathodes at the nano-scale have open new possibilities such as enhancing quantum eciency via surface-plasmon excitation, forming ultra-low-emittance beams, or producing structured electron beams. In this paper we present numerical investigations of the beam dynamics associated to this class of cathode in the weak- and strong-field regimes.We finally discuss the possible applications of some of the achievable cathode patterns when coupled with other phase space manipulations.

  12. Impedance Modeling of Solid Oxide Fuel Cell Cathodes

    DEFF Research Database (Denmark)

    Mortensen, Jakob Egeberg; Søgaard, Martin; Jacobsen, Torben

    2010-01-01

    A 1-dimensional impedance model for a solid oxide fuel cell cathode is formulated and applied to a cathode consisting of 50/50 wt% strontium doped lanthanum cobaltite and gadolinia doped ceria. A total of 42 impedance spectra were recorded in the temperature range: 555-852°C and in the oxygen...... physical parameters such as the cathode thickness. ©2010 COPYRIGHT ECS - The Electrochemical Society...

  13. Structured electron beams from nano-engineered cathodes

    Science.gov (United States)

    Lueangaramwong, A.; Mihalcea, D.; Andonian, G.; Piot, P.

    2017-03-01

    The ability to engineer cathodes at the nano-scale have opened new possibilities such as enhancing quantum efficiency via surface-plasmon excitation, forming ultra-low-emittance beams, or producing structured electron beams. In this paper, we present numerical investigations of the beam dynamics associated with this class of cathode in the weak- and strong-field regimes. We finally discuss the possible applications of some of the achievable cathode patterns when coupled with other phase space manipulations.

  14. The Power Quality Compensation Strategy for Power Distribution System Based on Hybrid Parallel Active Power Filters

    Directory of Open Access Journals (Sweden)

    Rachid DEHINI

    2010-12-01

    Full Text Available In this paper, the main aim is to confront the performance of shunt active power filter (SAPF and the shunt hybrid active power filter (SHAPF to achieve flexibility and reliability of the filter devices. Both of the two devices used the classical proportional-integral controller for pulse generation to trigger the inventers MOSFET’s. In the adopted hybrid active filter there is a passive power filter with high power rating to filter the low order harmonies and one active filter with low power rating to filter the other high order harmonies. In order to investigate the effectiveness of (SHAPF, the studies have been accomplished using simulation with the MATLAB-SIMULINK. The results show That (SHAPF is more effective than (SAPF, and has lower cost.

  15. Pulsed Plasma Methods in Materials Processing

    Science.gov (United States)

    Rej, D. J.

    1996-05-01

    Plasmas are routinely used to synthesize advanced materials, because of their ability to produce reactant species that enable a wide variety of chemical reactions. For example, in microelectronics manufacturing, plasmas are used to etch, clean, ash photoresist, implant, deposit, polymerize, and metalize. The use of pulsed power may extend the utility of plasma processing. Pulsed devices such as coaxial plasma guns, cathodic arcs, pseudosparks have been employed to synthesize materials ranging from novel steel alloys and high-temperature superconductors to diamond coatings. In this talk, we will highlight plasma immersion ion implantation and deposition, methods that improve conventional steady-state chemical and physical vapor deposition techniques. Pulsed power enables energetic ion bombardment before plasma deposition to promote better film adhesion through the formation of a graded interface. Ion bombardment during deposition reduces residual stress in the deposited film, thereby enabling formation of thick layers. Also, pulsed plasma sources have advantages over steady-state devices in that they conserve electrical power and can produce high-density, fully-dissociated plasmas. As an example, we will review recent experiments on the formation of adherent diamond-like carbon films deposited onto relatively large batches of automotive components.

  16. Design of the LC+trap filter for a current source rectifier

    DEFF Research Database (Denmark)

    Min, Huang; Wang, Xiongfei; Loh, Poh Chiang

    2015-01-01

    capacitor voltage and the line current THD for space vector modulation. The resonance of the input filter can be excited by the Pulse Width Modulation (PWM) and a simple passive damping can damp the resonances. The analysis and design of the input filter have been verified by simulations in MATLAB/Simulink....

  17. A class of high-pass digital MTI filters with nonuniform PRF

    NARCIS (Netherlands)

    Prinsen, P.J.A.

    1973-01-01

    A class of digital feed-forward filters is developed, satisfying the requirement of a maximally flat stopband characteristic at zero frequency if the pulse-repetition frequency is modulated. A simple algorithm is given to obtain the filter coefficients. Some properties are summarized

  18. Voltammetric and electrochemical impedance spectroscopy characterization of a cathodic and anodic pre-treated boron doped diamond electrode

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, S. Carlos B. [Departamento de Quimica, Faculdade de Ciencias e Tecnologia, Universidade de Coimbra, 3004-535 Coimbra (Portugal); Oliveira-Brett, Ana Maria, E-mail: brett@ci.uc.p [Departamento de Quimica, Faculdade de Ciencias e Tecnologia, Universidade de Coimbra, 3004-535 Coimbra (Portugal)

    2010-06-01

    The effect of boron doped diamond (BDD) surface termination, immediately after cathodic and anodic electrochemical pre-treatments, on the electrochemical response of a BDD electrode in aqueous media and the influence of the different supporting electrolytes utilized in these pre-treatments on the final surface termination was investigated with [Fe(CN){sub 6}]{sup 4-/3-}, as redox probe, by cyclic and differential pulse voltammetry and electrochemical impedance spectroscopy. The cyclic voltammetry results indicate that the electrochemical behavior for the redox couple [Fe(CN){sub 6}]{sup 4-/3-} is very dependent on the state of the BDD surface, and a reversible response was observed after the cathodic electrochemical pre-treatment, whereas a quasi-reversible response occurred after anodic electrochemical pre-treatment. Differential pulse voltammetry in acetate buffer also showed that the potential window is very much influenced by the electrochemical pre-treatment of the BDD surface. Electroactivity of non-diamond carbon surface species (sp{sup 2} inclusions) incorporated into the diamond structure was observed after cathodic and anodic pre-treatments. Electrochemical impedance spectroscopy confirmed the cyclic voltammetry results and indicates that the BDD surface resistance and capacitance vary significantly with the electrolyte and with the electrochemical pre-treatment, caused by different surface terminations of the BDD electrode surface.

  19. Apparatuses for making cathodes for high-temperature, rechargeable batteries

    Energy Technology Data Exchange (ETDEWEB)

    Meinhardt, Kerry D.; Sprenkle, Vincent L.; Coffey, Gregory W.

    2016-09-13

    The approaches and apparatuses for fabricating cathodes can be adapted to improve control over cathode composition and to better accommodate batteries of any shape and their assembly. For example, a first solid having an alkali metal halide, a second solid having a transition metal, and a third solid having an alkali metal aluminum halide are combined into a mixture. The mixture can be heated in a vacuum to a temperature that is greater than or equal to the melting point of the third solid. When the third solid is substantially molten liquid, the mixture is compressed into a desired cathode shape and then cooled to solidify the mixture in the desired cathode shape.

  20. Importance of OH(-) transport from cathodes in microbial fuel cells.

    Science.gov (United States)

    Popat, Sudeep C; Ki, Dongwon; Rittmann, Bruce E; Torres, César I

    2012-06-01

    Cathodic limitation in microbial fuel cells (MFCs) is considered an important hurdle towards practical application as a bioenergy technology. The oxygen reduction reaction (ORR) needs to occur in MFCs under significantly different conditions compared to chemical fuel cells, including a neutral pH. The common reason cited for cathodic limitation is the difficulty in providing protons to the catalyst sites. Here, we show that it is not the availability of protons, but the transport of OH(-) from the catalyst layer to the bulk liquid that largely governs cathodic potential losses. OH(-) is a product of an ORR mechanism that has not been considered dominant before. The accumulation of OH(-) at the catalyst sites results in an increase in the local cathode pH, resulting in Nernstian concentration losses. For Pt-based gas-diffusion cathodes, using polarization curves developed in unbuffered and buffered solutions, we quantified this loss to be >0.3 V at a current density of 10 Am(-2) . We show that this loss can be partially overcome by replacing the Nafion binder used in the cathode catalyst layer with an anion-conducting binder and by providing additional buffer to the cathode catalyst directly in the form of CO(2) , which results in enhanced OH(-) transport. Our results provide a comprehensive analysis of cathodic limitations in MFCs and should allow researchers to develop and select materials for the construction of MFC cathodes and identify operational conditions that will help minimize Nernstian concentration losses due to pH gradients.