Accurate step-FMCW ultrasound ranging and comparison with pulse-echo signaling methods

Science.gov (United States)

Natarajan, Shyam; Singh, Rahul S.; Lee, Michael; Cox, Brian P.; Culjat, Martin O.; Grundfest, Warren S.; Lee, Hua

2010-03-01

This paper presents a method setup for high-frequency ultrasound ranging based on stepped frequency-modulated continuous waves (FMCW), potentially capable of producing a higher signal-to-noise ratio (SNR) compared to traditional pulse-echo signaling. In current ultrasound systems, the use of higher frequencies (10-20 MHz) to enhance resolution lowers signal quality due to frequency-dependent attenuation. The proposed ultrasound signaling format, step-FMCW, is well-known in the radar community, and features lower peak power, wider dynamic range, lower noise figure and simpler electronics in comparison to pulse-echo systems. In pulse-echo ultrasound ranging, distances are calculated using the transmit times between a pulse and its subsequent echoes. In step-FMCW ultrasonic ranging, the phase and magnitude differences at stepped frequencies are used to sample the frequency domain. Thus, by taking the inverse Fourier transform, a comprehensive range profile is recovered that has increased immunity to noise over conventional ranging methods. Step-FMCW and pulse-echo waveforms were created using custom-built hardware consisting of an arbitrary waveform generator and dual-channel super heterodyne receiver, providing high SNR and in turn, accuracy in detection.

Fast quadrupole pulsed power supply in the AGS

International Nuclear Information System (INIS)

Nawrocky, R.J.; Halama, H.J.; Lambiase, R.F.; Montemurro, P.A.

1984-01-01

As part of the Polarized Proton Project at the AGS, a pulsed power supply system has been developed to energize a set of twelve fast quadrupoles which are symmetrically distributed around the 1/2-mile circumference of the machine. During a typical acceleration cycle, which is normally repeated every 2.4 s, these magnets are energized with bursts of triangular current pulses. The rise-time of each pulse is less than 2 μs and the width at the base varies from 1 to 3.5 ms depending on the pulse. Within a burst, pulses alternate in polarity and vary in amplitude from 160 A to 2700 A peak. Pulse separation is on the order of 40 ms. Due to the distributed nature of the load and high di/dt, each magnet is powered by a separate modulator. Magnets are driven via coaxial pulse transmission cables up to 200 ft long. In the modulators, the high power pulses are switched with thyratron/ignitron switch pairs. All modulators are charged in parallel with a common system of programmable high voltage power supplies. The overall system is controlled with a distributed network of microcomputers. This paper describes the development, construction and initial performance of the pulsed power supply system

The Real-time Frequency Spectrum Analysis of Neutron Pulse Signal Series

International Nuclear Information System (INIS)

Tang Yuelin; Ren Yong; Wei Biao; Feng Peng; Mi Deling; Pan Yingjun; Li Jiansheng; Ye Cenming

2009-01-01

The frequency spectrum analysis of neutron pulse signal is a very important method in nuclear stochastic signal processing Focused on the special '0' and '1' of neutron pulse signal series, this paper proposes new rotation-table and realizes a real-time frequency spectrum algorithm under 1G Hz sample rate based on PC with add, address and SSE. The numerical experimental results show that under the count rate of 3X10 6 s -1 , this algorithm is superior to FFTW in time-consumption and can meet the real-time requirement of frequency spectrum analysis. (authors)

Analysis of pulse-shape discrimination techniques for BC501A using GHz digital signal processing

International Nuclear Information System (INIS)

Rooney, B.D.; Dinwiddie, D.R.; Nelson, M.A.; Rawool-Sullivan, Mohini W.

2001-01-01

A comparison study of pulse-shape analysis techniques was conducted for a BC501A scintillator using digital signal processing (DSP). In this study, output signals from a preamplifier were input directly into a 1 GHz analog-to-digital converter. The digitized data obtained with this method was post-processed for both pulse-height and pulse-shape information. Several different analysis techniques were evaluated for neutron and gamma-ray pulse-shape discrimination. It was surprising that one of the simplest and fastest techniques resulted in some of the best pulse-shape discrimination results. This technique, referred to here as the Integral Ratio technique, was able to effectively process several thousand detector pulses per second. This paper presents the results and findings of this study for various pulse-shape analysis techniques with digitized detector signals.

Key technology research of nuclear signal digitized pulse shaping in real time

International Nuclear Information System (INIS)

Zhou Jianbin; Wang Min; Zhou Wei; Zhu Xing; Liu Yi; Chen Bao; Lu Baoping; Yue Aizhong; Qin Li; He Xuxin

2014-01-01

The computer simulation and analysis were carried out for the ideal nuclear pulse signal and the actual detector output signals, and the determination method of digital trapezoidal shape parameter for different nuclear pulse shaping time was summarized. At high count rate measurement occasion, the effective count rate is increased, some pile-up pulses are eliminated and the accumulation of dead time of the system is reduced. Meanwhile, Si-PIN semiconductor detector performance was tested by 256 points and 512 points digital triangle forming methods and the analog circuit forming methods for comparative tests. Test results show that the pulse forming treatment method increases the count rate performance and the resolution of detector. (authors)

Wavelet-Based Signal Processing of Electromagnetic Pulse Generated Waveforms

National Research Council Canada - National Science Library

Ardolino, Richard S

2007-01-01

This thesis investigated and compared alternative signal processing techniques that used wavelet-based methods instead of traditional frequency domain methods for processing measured electromagnetic pulse (EMP) waveforms...

Pulsed IRSL: A stable and fast bleaching luminescence signal from feldspar for dating Quaternary sediments

DEFF Research Database (Denmark)

Tsukamoto, Sumiko; Kondo, Reisuke; Lauer, Tobias

2017-01-01

, the pIRIR signal is nearly free from anomalous fading, but it is more difficult to reset during daylight exposure; the latter characteristic may give rise to age over-estimation in some environments because of partial bleaching. The pulsed IRSL signal has also been known to be less affected by anomalous...... and tephrochronology. We observe that under exposure to solar simulator, the pulsed IR50 signal bleaches as rapidly as the CW IR50, and much more rapidly than the pIRIR signals. Furthermore, the pulsed IR50 signal is also as stable as the pIRIR signals, especially when the middle part of the decay curve is used...

Signal-enhancement reflective pulse oximeter with Fresnel lens

Science.gov (United States)

Chung, Shuang-Chao; Sun, Ching-Cherng

2016-09-01

In this paper, a new reflective pulse oximeter is proposed and demonstrated with implanting a Fresnel lens, which enhances the reflected signal. An optical simulation model incorporated with human skin characteristics is presented to evaluate the capability of the Fresnel lens. In addition, the distance between the light emitting diode and the photodiode is optimized. Compared with the other reflective oximeters, the reflected signal light detected by the photodiode is enhanced to more than 140%.

Pulse shape discrimination based on fast signals from silicon photomultipliers

Science.gov (United States)

Yu, Junhao; Wei, Zhiyong; Fang, Meihua; Zhang, Zixia; Cheng, Can; Wang, Yi; Su, Huiwen; Ran, Youquan; Zhu, Qingwei; Zhang, He; Duan, Kai; Chen, Ming; Liu, Meng

2018-06-01

Recent developments in organic plastic scintillators capable of pulse shape discrimination (PSD) enable a breakthrough in discrimination between neutrons and gammas. Plastic scintillator detectors coupled with silicon photomultipliers (SiPMs) offer many advantages, such as lower power consumption, smaller volume, and especially insensitivity to magnetic fields, compared with conventional photomultiplier tubes (PMTs). A SensL SiPM has two outputs: a standard output and a fast output. It is known that the charge injected into the fast output electrode is typically approximately 2% of the total charge generated during the avalanche, whereas the charge injected into the standard output electrode is nearly 98% of the total. Fast signals from SiPMs exhibit better performance in terms of timing and time-correlated measurements compared with standard signals. The pulse duration of a standard signal is on the order of hundreds of nanoseconds, whereas the pulse duration of the main monopole waveform of a fast signal is a few tens of nanoseconds. Fast signals are traditionally thought to be suitable for photon counting at very high speeds but unsuitable for PSD due to the partial charge collection. Meanwhile, the standard outputs of SiPMs coupled with discriminating scintillators have yielded nice PSD performances, but there have been no reports on PSD using fast signals. Our analysis shows that fast signals can also provide discrimination if the rate of charge injection into the fast output electrode is fixed for each event, even though only a portion of the charge is collected. In this work, we achieved successful PSD using fast signals; meanwhile, using a coincidence timing window of less 3 nanoseconds between the readouts from both ends of the detector reduced the influence of the high SiPM dark current. We experimentally achieved good timing performance and PSD capability simultaneously.

Full-field wrist pulse signal acquisition and analysis by 3D Digital Image Correlation

Science.gov (United States)

Xue, Yuan; Su, Yong; Zhang, Chi; Xu, Xiaohai; Gao, Zeren; Wu, Shangquan; Zhang, Qingchuan; Wu, Xiaoping

2017-11-01

Pulse diagnosis is an essential part in four basic diagnostic methods (inspection, listening, inquiring and palpation) in traditional Chinese medicine, which depends on longtime training and rich experience, so computerized pulse acquisition has been proposed and studied to ensure the objectivity. To imitate the process that doctors using three fingertips with different pressures to feel fluctuations in certain areas containing three acupoints, we established a five dimensional pulse signal acquisition system adopting a non-contacting optical metrology method, 3D digital image correlation, to record the full-field displacements of skin fluctuations under different pressures. The system realizes real-time full-field vibration mode observation with 10 FPS. The maximum sample frequency is 472 Hz for detailed post-processing. After acquisition, the signals are analyzed according to the amplitude, pressure, and pulse wave velocity. The proposed system provides a novel optical approach for digitalizing pulse diagnosis and massive pulse signal data acquisition for various types of patients.

Wideband Small-Signal Input dq Admittance Modeling of Six-Pulse Diode Rectifiers

DEFF Research Database (Denmark)

Yue, Xiaolong; Wang, Xiongfei; Blaabjerg, Frede

2018-01-01

This paper studies the wideband small-signal input dq admittance of six-pulse diode rectifiers. Considering the frequency coupling introduced by ripple frequency harmonics of d-and q-channel switching function, the proposed model successfully predicts the small-signal input dq admittance of six......-pulse diode rectifiers in high frequency regions that existing models fail to explain. Simulation and experimental results verify the accuracy of the proposed model....

Energía financiera

OpenAIRE

Altuve G., José G.

2016-01-01

La energía financiera surge como consecuencia de la unión de los conceptos energía y financiera. La primera, como la acción a seguir en un momento del tiempo, y la segunda vinculada al manejo de variables tales como: Estructura financiera y su costo de capital y, las decisiones de inversión consideradas bajo riesgo. Si se armonizan estos dos aspectos estamos en presencia de la fusión de la energía y la administración financiera en dos de sus variables más importantes. Financial power arise...

Brushless DC motor control system responsive to control signals generated by a computer or the like

Science.gov (United States)

Packard, Douglas T. (Inventor); Schmitt, Donald E. (Inventor)

1987-01-01

A control system for a brushless DC motor responsive to digital control signals is disclosed. The motor includes a multiphase wound stator and a permanent magnet rotor. The rotor is arranged so that each phase winding, when energized from a DC source, will drive the rotor through a predetermined angular position or step. A commutation signal generator responsive to the shaft position provides a commutation signal for each winding. A programmable control signal generator such as a computer or microprocessor produces individual digital control signals for each phase winding. The control signals and commutation signals associated with each winding are applied to an AND gate for that phase winding. Each gate controls a switch connected in series with the associated phase winding and the DC source so that each phase winding is energized only when the commutation signal and the control signal associated with that phase winding are present. The motor shaft may be advanced one step at a time to a desired position by applying a predetermined number of control signals in the proper sequence to the AND gates and the torque generated by the motor may be regulated by applying a separate control signal to each AND gate which is pulse width modulated to control the total time that each switch connects its associated winding to the DC source during each commutation period.

Pulsed voltage electrospray ion source and method for preventing analyte electrolysis

Science.gov (United States)

Kertesz, Vilmos [Knoxville, TN; Van Berkel, Gary [Clinton, TN

2011-12-27

An electrospray ion source and method of operation includes the application of pulsed voltage to prevent electrolysis of analytes with a low electrochemical potential. The electrospray ion source can include an emitter, a counter electrode, and a power supply. The emitter can include a liquid conduit, a primary working electrode having a liquid contacting surface, and a spray tip, where the liquid conduit and the working electrode are in liquid communication. The counter electrode can be proximate to, but separated from, the spray tip. The power system can supply voltage to the working electrode in the form of a pulse wave, where the pulse wave oscillates between at least an energized voltage and a relaxation voltage. The relaxation duration of the relaxation voltage can range from 1 millisecond to 35 milliseconds. The pulse duration of the energized voltage can be less than 1 millisecond and the frequency of the pulse wave can range from 30 to 800 Hz.

Investigation on the generation characteristic of pressure pulse wave signal during the measurement-while-drilling process

Science.gov (United States)

Changqing, Zhao; Kai, Liu; Tong, Zhao; Takei, Masahiro; Weian, Ren

2014-04-01

The mud-pulse logging instrument is an advanced measurement-while-drilling (MWD) tool and widely used by the industry in the world. In order to improve the signal transmission rate, ensure the accurate transmission of information and address the issue of the weak signal on the ground of oil and gas wells, the signal generator should send out the strong mud-pulse signals with the maximum amplitude. With the rotary valve pulse generator as the study object, the three-dimensional Reynolds NS equations and standard k - ɛ turbulent model were used as a mathematical model. The speed and pressure coupling calculation was done by simple algorithms to get the amplitudes of different rates of flow and axial clearances. Tests were done to verify the characteristics of the pressure signals. The pressure signal was captured by the standpiece pressure monitoring system. The study showed that the axial clearances grew bigger as the pressure wave amplitude value decreased and caused the weakening of the pulse signal. As the rate of flow got larger, the pressure wave amplitude would increase and the signal would be enhanced.

The depletion of protein signals in metabonomics analysis with the WET-CPMG pulse sequence

International Nuclear Information System (INIS)

Van, Que N.; Chmurny, Gwendolyn N.; Veenstra, Timothy D.

2003-01-01

Nuclear magnetic resonance (NMR) spectroscopy is a powerful analytical tool capable of providing a comprehensive metabolic profile of biofluids such as urine, plasma, and serum. Unfortunately, when measuring serum and plasma, the high protein concentration can obscure the signals originating from low molecular weight metabolites. We evaluated the use of different parameters within the Carr-Purcell-Meiboom-Gill (CPMG) pulse train of fast spin-echoes to remove the macromolecular signal contribution in one-dimensional proton ( 1 H) NMR spectra. Experimental parameters such as the refocusing delay in the CPMG pulse train, pulse miscalibration, and recycle time were examined to assess the ability to remove the protein signals from the spectrum without causing a deleterious effect on the signals originating from free, low molecular weight metabolites. The 1 H-NMR spectra of a variety of serum samples spiked with 2 ' -deoxyadenosine were acquired using various acquisition parameters. Our results show that the delay used in the CPMG spin-echo and the combination of the acquisition pulse flip angle and recycle time are the two major factors affecting the observed metabolite signal amplitudes in the resulting 1 H-NMR spectrum

Nuclear pulse signal processing technique based on blind deconvolution method

International Nuclear Information System (INIS)

Hong Pengfei; Yang Lei; Fu Tingyan; Qi Zhong; Li Dongcang; Ren Zhongguo

2012-01-01

In this paper, we present a method for measurement and analysis of nuclear pulse signal, with which pile-up signal is removed, the signal baseline is restored, and the original signal is obtained. The data acquisition system includes FPGA, ADC and USB. The FPGA controls the high-speed ADC to sample the signal of nuclear radiation, and the USB makes the ADC work on the Slave FIFO mode to implement high-speed transmission status. Using the LabVIEW, it accomplishes online data processing of the blind deconvolution algorithm and data display. The simulation and experimental results demonstrate advantages of the method. (authors)

Tree shoot bending generates hydraulic pressure pulses: a new long-distance signal?

Science.gov (United States)

Lopez, Rosana; Badel, Eric; Peraudeau, Sebastien; Leblanc-Fournier, Nathalie; Beaujard, François; Julien, Jean-Louis; Cochard, Hervé; Moulia, Bruno

2014-05-01

When tree stems are mechanically stimulated, a rapid long-distance signal is induced that slows down primary growth. An investigation was carried out to determine whether the signal might be borne by a mechanically induced pressure pulse in the xylem. Coupling xylem flow meters and pressure sensors with a mechanical testing device, the hydraulic effects of mechanical deformation of tree stem and branches were measured. Organs of several tree species were studied, including gymnosperms and angiosperms with different wood densities and anatomies. Bending had a negligible effect on xylem conductivity, even when deformations were sustained or were larger than would be encountered in nature. It was found that bending caused transient variation in the hydraulic pressure within the xylem of branch segments. This local transient increase in pressure in the xylem was rapidly propagated along the vascular system in planta to the upper and lower regions of the stem. It was shown that this hydraulic pulse originates from the apoplast. Water that was mobilized in the hydraulic pulses came from the saturated porous material of the conduits and their walls, suggesting that the poroelastic behaviour of xylem might be a key factor. Although likely to be a generic mechanical response, quantitative differences in the hydraulic pulse were found in different species, possibly related to differences in xylem anatomy. Importantly the hydraulic pulse was proportional to the strained volume, similar to known thigmomorphogenetic responses. It is hypothesized that the hydraulic pulse may be the signal that rapidly transmits mechanobiological information to leaves, roots, and apices.

Design of a Continuous Blood Pressure Measurement System Based on Pulse Wave and ECG Signals.

Science.gov (United States)

Li, Jian-Qiang; Li, Rui; Chen, Zhuang-Zhuang; Deng, Gen-Qiang; Wang, Huihui; Mavromoustakis, Constandinos X; Song, Houbing; Ming, Zhong

2018-01-01

With increasingly fierce competition for jobs, the pressures on people have risen in recent years, leading to lifestyle and diet disorders that result in significantly higher risks of cardiovascular disease. Hypertension is one of the common chronic cardiovascular diseases; however, mainstream blood pressure measurement devices are relatively heavy. When multiple measurements are required, the user experience and the measurement results may be unsatisfactory. In this paper, we describe the design of a signal collection module that collects pulse waves and electrocardiograph (ECG) signals. The collected signals are input into a signal processing module to filter the noise and amplify the useful physiological signals. Then, we use a wavelet transform to eliminate baseline drift noise and detect the feature points of the pulse waves and ECG signals. We propose the concept of detecting the wave shape associated with an instance, an approach that minimizes the impact of atypical pulse waves on blood pressure measurements. Finally, we propose an improved method for measuring blood pressure based on pulse wave velocity that improves the accuracy of blood pressure measurements by 58%. Moreover, the results meet the american medical instrument promotion association standards, which demonstrate the feasibility of our measurement system.

Analysis of the computational requirements of a pulse-doppler radar signal processor

CSIR Research Space (South Africa)

Broich, R

2012-05-01

Full Text Available In an attempt to find an optimal processing architecture for radar signal processing applications, the different algorithms that are typically used in a pulse-Doppler radar signal processor are investigated. Radar algorithms are broken down...

Cavity-less sub-picosecond pulse generation for the demultiplexing of a 640 Gbaud OTDM signal

DEFF Research Database (Denmark)

Kong, Deming; Guan, Pengyu; Hu, Hao

2015-01-01

A 703 fs cavity-less pulse source based on pulse carving and pulse compression is demonstrated and utilized for demultiplexing a 640 Gbaud OTDM signal. Timing jitter is found to be the main limiting factor....

Investigation of signal processing algorithms for an embedded microcontroller-based wearable pulse oximeter.

Science.gov (United States)

Johnston, W S; Mendelson, Y

2006-01-01

Despite steady progress in the miniaturization of pulse oximeters over the years, significant challenges remain since advanced signal processing must be implemented efficiently in real-time by a relatively small size wearable device. The goal of this study was to investigate several potential digital signal processing algorithms for computing arterial oxygen saturation (SpO(2)) and heart rate (HR) in a battery-operated wearable reflectance pulse oximeter that is being developed in our laboratory for use by medics and first responders in the field. We found that a differential measurement approach, combined with a low-pass filter (LPF), yielded the most suitable signal processing technique for estimating SpO(2), while a signal derivative approach produced the most accurate HR measurements.

Interference and protection of electromagnetic pulse to digital signal processor

International Nuclear Information System (INIS)

Wang Yan; Jiao Hongling; He Shanhong; Pan Chao; Feng Deren; Che Wenquan; Xiong Ying

2013-01-01

The effective electromagnetic pulse protection is studied in this paper, first the interference of electromagnetic pulse simulator path is analyzed, including the digital signal processor (DSP) and the discharge circuit of coupling interference and net electricity coupling interference. Using the structure optimization design, the hardware block reinforcement measurement and the setting of open software trap, and the watchdog anti-jamming measures, the interference test is completed such as the central processor core voltage of DSP, input/output (I/O) ports of DSP and the display screen. The experimental results show that the combination of hardware and software protection reinforcement technology is effective, and the interference pulse amplitude of DSP board I/O port and the kernel work voltage are reduced, and the interference duration is reduced from 2 μs to 400 ns. The interference pulse is effectively restrained. (authors)

Energized Oxygen : Speiser Current Sheet Bifurcation

Science.gov (United States)

George, D. E.; Jahn, J. M.

2017-12-01

A single population of energized Oxygen (O+) is shown to produce a cross-tail bifurcated current sheet in 2.5D PIC simulations of the magnetotail without the influence of magnetic reconnection. Treatment of oxygen in simulations of space plasmas, specifically a magnetotail current sheet, has been limited to thermal energies despite observations of and mechanisms which explain energized ions. We performed simulations of a homogeneous oxygen background, that has been energized in a physically appropriate manner, to study the behavior of current sheets and magnetic reconnection, specifically their bifurcation. This work uses a 2.5D explicit Particle-In-a-Cell (PIC) code to investigate the dynamics of energized heavy ions as they stream Dawn-to-Dusk in the magnetotail current sheet. We present a simulation study dealing with the response of a current sheet system to energized oxygen ions. We establish a, well known and studied, 2-species GEM Challenge Harris current sheet as a starting point. This system is known to eventually evolve and produce magnetic reconnection upon thinning of the current sheet. We added a uniform distribution of thermal O+ to the background. This 3-species system is also known to eventually evolve and produce magnetic reconnection. We add one additional variable to the system by providing an initial duskward velocity to energize the O+. We also traced individual particle motion within the PIC simulation. Three main results are shown. First, energized dawn- dusk streaming ions are clearly seen to exhibit sustained Speiser motion. Second, a single population of heavy ions clearly produces a stable bifurcated current sheet. Third, magnetic reconnection is not required to produce the bifurcated current sheet. Finally a bifurcated current sheet is compatible with the Harris current sheet model. This work is the first step in a series of investigations aimed at studying the effects of energized heavy ions on magnetic reconnection. This work differs

Study of time-domain digital pulse shaping algorithms for nuclear signals

International Nuclear Information System (INIS)

Zhou Jianbin; Tuo Xianguo; Zhu Xing; Liu Yi; Zhou Wei; Lei Jiarong

2012-01-01

With the development on high-speed integrated circuit, fast high resolution sampling ADC and digital signal processors are replacing analog shaping amplifier circuit. This paper firstly presents the numerical analysis and simulation on R-C shaping circuit model and C-R shaping circuit model. Mathematic models are established based on 1 st order digital differential method and Kirchhoff Current Law in time domain, and a simulation and error evaluation experiment on an ideal digital signal are carried out with Excel VBA. A digital shaping test for a semiconductor X-ray detector in real time is also presented. Then a numerical analysis for Sallen-Key(S-K) low-pass filter circuit model is implemented based on the analysis of digital R-C and digital C-R shaping methods. By applying the 2 nd order non-homogeneous differential equation,the authors implement a digital Gaussian filter model for a standard exponential-decaying signal and a nuclear pulse signal. Finally, computer simulations and experimental tests are carried out and the results show the possibility of the digital pulse processing algorithms. (authors)

Estudio energético del sistema eléctrico en Ecuador. Impulso a la Energía Solar Fotovoltaica

OpenAIRE

Eras Almeida, Andrea Alejandra

2012-01-01

La realización de este proyecto en base a la legislación que promueve el desarrollo de la energía limpia, pretende mostrar los cambios que tendrá la matriz energética del Ecuador si se impone un aporte renovable a la producción de energía y sus beneficios con sus futuros proyectos emblemáticos. Así también, pretende el impulso a la energía solar fotovolataica a nivel de construcciones fijas, con inversión privada y para beneficio de la sociedad misma.

FPGA based hardware optimized implementation of signal processing system for LFM pulsed radar

Science.gov (United States)

Azim, Noor ul; Jun, Wang

2016-11-01

Signal processing is one of the main parts of any radar system. Different signal processing algorithms are used to extract information about different parameters like range, speed, direction etc, of a target in the field of radar communication. This paper presents LFM (Linear Frequency Modulation) pulsed radar signal processing algorithms which are used to improve target detection, range resolution and to estimate the speed of a target. Firstly, these algorithms are simulated in MATLAB to verify the concept and theory. After the conceptual verification in MATLAB, the simulation is converted into implementation on hardware using Xilinx FPGA. Chosen FPGA is Xilinx Virtex-6 (XC6LVX75T). For hardware implementation pipeline optimization is adopted and also other factors are considered for resources optimization in the process of implementation. Focusing algorithms in this work for improving target detection, range resolution and speed estimation are hardware optimized fast convolution processing based pulse compression and pulse Doppler processing.

XUV pulse effect on signal modulations of harmonic spectra from H2+ and T2+

Science.gov (United States)

Feng, Liqiang; Liu, Hang; Kapteyn, Henry J.; Feng, April Y.

2018-05-01

The effects of signal modulations on the molecular high-order harmonic generations in H2^{+ } and T2+ have been theoretically investigated. It is found that with the introduction of the XUV pulse, due to the absorption of the extra XUV photons in the recombination process, multiplateaus on the harmonic spectra, separated by the XUV photon energy can be found. Moreover, this multiplateau structure is insensitive to the wavelength of the XUV pulse. In shorter pulse duration, the intensities of the multiplateaus from H2+ are higher than those from T2+; while in longer pulse duration, the opposite results can be found. Finally, by changing the delay time of the XUV pulse, the signal modulations (including the amplitude and the frequency modulations) of the multiplateaus can be controlled.

Electrical and optical analysis of fast transient discharges in a pulsed corona pilot unit

NARCIS (Netherlands)

Blom, P.P.M.; Smulders, H.W.M.; Heesch, van E.J.M.; Laan, van der P.C.T.

1997-01-01

We give a detailed analysis of intense pulsed corona dis charges. CCD movies and current, voltage and energy in put measurements are the basis of the description. The discharges are generated in a 1.5 kW pilot unit, which cre ates pulsed corona discharges energized by 100 kV pulses of 200 us width,

A high speed digital signal averager for pulsed NMR

International Nuclear Information System (INIS)

Srinivasan, R.; Ramakrishna, J.; Ra agopalan, S.R.

1978-01-01

A 256-channel digital signal averager suitable for pulsed nuclear magnetic resonance spectroscopy is described. It implements 'stable averaging' algorithm and hence provides a calibrated display of the average signal at all times during the averaging process on a CRT. It has a maximum sampling rate of 2.5 μ sec and a memory capacity of 256 x 12 bit words. Number of sweeps is selectable through a front panel control in binary steps from 2 3 to 2 12 . The enhanced signal can be displayed either on a CRT or by a 3.5-digit LED display. The maximum S/N improvement that can be achieved with this instrument is 36 dB. (auth.)

Energía minihidráulica : una alternativa energética para electrificación rural

OpenAIRE

Agudelo Flórez, Sergio Cipriano; Chamorro Rendón, Luis Javier

2002-01-01

Entre las actividades del Grupo de Energía Alternativa (GEA) de la Facultad de Ingeniería de la Universidad de Antioquia, se pretende el desarrollo de prototipos que aprovechen las fuentes no convencionales para la producción de energía eléctrica y así satisfacer las necesidades insatisfechas de las viviendas rurales aisladas de la red energética nacional. En la región del Oriente antioqueño, se encontró un formidable recurso hidráulico de grandes ríos, quebradas y fuentes de agua cercanas a ...

Wireless energizing system for an automated implantable sensor

Energy Technology Data Exchange (ETDEWEB)

Swain, Biswaranjan; Nayak, Praveen P.; Kar, Durga P.; Bhuyan, Satyanarayan; Mishra, Laxmi P. [Department of Electronics and Instrumentation Engineering, Siksha ‘O’ Anusandhan University, Bhubaneswar 751030 (India)

2016-07-15

The wireless drive of an automated implantable electronic sensor has been explored for health monitoring applications. The proposed system comprises of an automated biomedical sensing system which is energized through resonant inductive coupling. The implantable sensor unit is able to monitor the body temperature parameter and sends back the corresponding telemetry data wirelessly to the data recoding unit. It has been observed that the wireless power delivery system is capable of energizing the automated biomedical implantable electronic sensor placed over a distance of 3 cm from the power transmitter with an energy transfer efficiency of 26% at the operating resonant frequency of 562 kHz. This proposed method ensures real-time monitoring of different human body temperatures around the clock. The monitored temperature data have been compared with a calibrated temperature measurement system to ascertain the accuracy of the proposed system. The investigated technique can also be useful for monitoring other body parameters such as blood pressure, bladder pressure, and physiological signals of the patient in vivo using various implantable sensors.

Wireless energizing system for an automated implantable sensor

International Nuclear Information System (INIS)

Swain, Biswaranjan; Nayak, Praveen P.; Kar, Durga P.; Bhuyan, Satyanarayan; Mishra, Laxmi P.

2016-01-01

The wireless drive of an automated implantable electronic sensor has been explored for health monitoring applications. The proposed system comprises of an automated biomedical sensing system which is energized through resonant inductive coupling. The implantable sensor unit is able to monitor the body temperature parameter and sends back the corresponding telemetry data wirelessly to the data recoding unit. It has been observed that the wireless power delivery system is capable of energizing the automated biomedical implantable electronic sensor placed over a distance of 3 cm from the power transmitter with an energy transfer efficiency of 26% at the operating resonant frequency of 562 kHz. This proposed method ensures real-time monitoring of different human body temperatures around the clock. The monitored temperature data have been compared with a calibrated temperature measurement system to ascertain the accuracy of the proposed system. The investigated technique can also be useful for monitoring other body parameters such as blood pressure, bladder pressure, and physiological signals of the patient in vivo using various implantable sensors.

Wireless energizing system for an automated implantable sensor.

Science.gov (United States)

Swain, Biswaranjan; Nayak, Praveen P; Kar, Durga P; Bhuyan, Satyanarayan; Mishra, Laxmi P

2016-07-01

The wireless drive of an automated implantable electronic sensor has been explored for health monitoring applications. The proposed system comprises of an automated biomedical sensing system which is energized through resonant inductive coupling. The implantable sensor unit is able to monitor the body temperature parameter and sends back the corresponding telemetry data wirelessly to the data recoding unit. It has been observed that the wireless power delivery system is capable of energizing the automated biomedical implantable electronic sensor placed over a distance of 3 cm from the power transmitter with an energy transfer efficiency of 26% at the operating resonant frequency of 562 kHz. This proposed method ensures real-time monitoring of different human body temperatures around the clock. The monitored temperature data have been compared with a calibrated temperature measurement system to ascertain the accuracy of the proposed system. The investigated technique can also be useful for monitoring other body parameters such as blood pressure, bladder pressure, and physiological signals of the patient in vivo using various implantable sensors.

Design of pulse oximetry signal based on personal computer for detection oxygen saturation

International Nuclear Information System (INIS)

Umi Salamah; Margi Sasono

2015-01-01

The lack or excess of oxygen in the blood will cause healthy and body system disorder. At certain level, the disease can lead to death. For that reason, the information about oxygen saturation in blood becomes important to be identified. One of the devices used to monitor the blood oxygen saturation is pulse oximetry. This research attempt to designed Pulse Oximetry based on personal computer using red LED and infrared as its light source, while the light sensor using photodiode. The designed Pulse Oximetry is a non-invasive instrumentation which LED drivers is placed on the fingertips. The LED light goes through the finger will be a signal that is fed to the photodiode and will be converted into digital signals by ADC (Analog to Digital Converter) and will be processed further by a personal computer to display the pulse oximetry graphics. This study uses Delphi 7, Microsoft Excel, and Mt Lab as its software.This designed pulse oximetry has been tested in two peoples: sample A, male 38 years; and sample B, a woman 23 years old. Oxygen saturation of sample A is 80.75, while the sample B is 90.75. (author)

Pulse-height loss in the signal readout circuit of compound semiconductor detectors

Science.gov (United States)

Nakhostin, M.; Hitomi, K.

2018-06-01

Compound semiconductor detectors such as CdTe, CdZnTe, HgI2 and TlBr are known to exhibit large variations in their charge collection times. This paper considers the effect of such variations on the measurement of induced charge pulses by using resistive feedback charge-sensitive preamplifiers. It is shown that, due to the finite decay-time constant of the preamplifiers, the capacitive decay during the signal readout leads to a variable deficit in the measurement of ballistic signals and a digital pulse processing method is employed to correct for it. The method is experimentally examined by using sampled pulses from a TlBr detector coupled to a charge-sensitive preamplifier with 150 μs of decay-time constant and 20 % improvement in the energy resolution of the detector at 662 keV is achieved. The implications of the capacitive decay on the correction of charge-trapping effect by using depth-sensing technique are also considered.

A paradoxical signal intensity increase in fatty livers using opposed-phase gradient echo imaging with fat-suppression pulses

International Nuclear Information System (INIS)

Mulkern, Robert V.; Voss, Stephan; Loeb Salsberg, Sandra; Krauel, Marta Ramon; Ludwig, David S.

2008-01-01

With the increase in obese and overweight children, nonalcoholic fatty liver disease has become more prevalent in the pediatric population. Appreciating subtleties of magnetic resonance (MR) signal intensity behavior from fatty livers under different imaging conditions thus becomes important to pediatric radiologists. We report an initially confusing signal behavior - increased signal from fatty livers when fat-suppression pulses are applied in an opposed-phase gradient echo imaging sequence - and seek to explain the physical mechanisms for this paradoxical signal intensity behavior. Abdominal MR imaging at 3 T with a 3-D volumetric interpolated breath-hold (VIBE) sequence in the opposed-phase condition (TR/TE 3.3/1.3 ms) was performed in five obese boys (14±2 years of age, body mass index >95th percentile for age and sex) with spectroscopically confirmed fatty livers. Two VIBE acquisitions were performed, one with and one without the use of chemical shift selective (CHESS) pulse fat suppression. The ratios of fat-suppressed over non-fat-suppressed signal intensities were assessed in regions-of-interest (ROIs) in five tissues: subcutaneous fat, liver, vertebral marrow, muscle and spleen. The boys had spectroscopically estimated hepatic fat levels between 17% and 48%. CHESS pulse fat suppression decreased subcutaneous fat signals dramatically, by more than 85% within regions of optimal fat suppression. Fatty liver signals, in contrast, were elevated by an average of 87% with CHESS pulse fat suppression. Vertebral marrow signal was also significantly elevated with CHESS pulse fat suppression, while spleen and muscle signals demonstrated only small signal increases on the order of 10%. We demonstrated that CHESS pulse fat suppression actually increases the signal intensity from fatty livers in opposed-phase gradient echo imaging conditions. The increase can be attributed to suppression of one partner of the opposed-phase pair that normally contributes to the

A paradoxical signal intensity increase in fatty livers using opposed-phase gradient echo imaging with fat-suppression pulses

Energy Technology Data Exchange (ETDEWEB)

Mulkern, Robert V.; Voss, Stephan [Harvard Medical School, Department of Radiology, Children' s Hospital Boston, Boston, MA (United States); Loeb Salsberg, Sandra; Krauel, Marta Ramon; Ludwig, David S. [Harvard Medical School, Department of Medicine, Children' s Hospital Boston, Boston, MA (United States)

2008-10-15

With the increase in obese and overweight children, nonalcoholic fatty liver disease has become more prevalent in the pediatric population. Appreciating subtleties of magnetic resonance (MR) signal intensity behavior from fatty livers under different imaging conditions thus becomes important to pediatric radiologists. We report an initially confusing signal behavior - increased signal from fatty livers when fat-suppression pulses are applied in an opposed-phase gradient echo imaging sequence - and seek to explain the physical mechanisms for this paradoxical signal intensity behavior. Abdominal MR imaging at 3 T with a 3-D volumetric interpolated breath-hold (VIBE) sequence in the opposed-phase condition (TR/TE 3.3/1.3 ms) was performed in five obese boys (14{+-}2 years of age, body mass index >95th percentile for age and sex) with spectroscopically confirmed fatty livers. Two VIBE acquisitions were performed, one with and one without the use of chemical shift selective (CHESS) pulse fat suppression. The ratios of fat-suppressed over non-fat-suppressed signal intensities were assessed in regions-of-interest (ROIs) in five tissues: subcutaneous fat, liver, vertebral marrow, muscle and spleen. The boys had spectroscopically estimated hepatic fat levels between 17% and 48%. CHESS pulse fat suppression decreased subcutaneous fat signals dramatically, by more than 85% within regions of optimal fat suppression. Fatty liver signals, in contrast, were elevated by an average of 87% with CHESS pulse fat suppression. Vertebral marrow signal was also significantly elevated with CHESS pulse fat suppression, while spleen and muscle signals demonstrated only small signal increases on the order of 10%. We demonstrated that CHESS pulse fat suppression actually increases the signal intensity from fatty livers in opposed-phase gradient echo imaging conditions. The increase can be attributed to suppression of one partner of the opposed-phase pair that normally contributes to the

Pulsed arterial spin labeling using TurboFLASH with suppression of intravascular signal.

Science.gov (United States)

Pell, Gaby S; Lewis, David P; Branch, Craig A

2003-02-01

Accurate quantification of perfusion with the ADC techniques requires the suppression of the majority of the intravascular signal. This is normally achieved with the use of diffusion gradients. The TurboFLASH sequence with its ultrashort repetition times is not readily amenable to this scheme. This report demonstrates the implementation of a modified TurboFLASH sequence for FAIR imaging. Intravascular suppression is achieved with a modified preparation period that includes a driven equilibrium Fourier transform (DEFT) combination of 90 degrees-180 degrees-90 degrees hard RF pulses subsequent to the inversion delay. These pulses rotate the perfusion-prepared magnetization into the transverse plane where it can experience the suitably placed diffusion gradients before being returned to the longitudinal direction by the second 90 degrees pulse. A value of b = 20-30 s/mm(2) was thereby found to suppress the majority of the intravascular signal. For single-slice perfusion imaging, quantification is only slightly modified. The technique can be readily extended to multislice acquisition if the evolving flow signal after the DEFT preparation is considered. An advantage of the modified preparation scheme is evident in the multislice FAIR images by the preservation of the sign of the magnetization difference. Copyright 2003 Wiley-Liss, Inc.

Investigations on the relationship between power spectrum and signal-to-noise ratio of frequency-swept pulses

International Nuclear Information System (INIS)

Zhang Zhuhong; Fan Diayuan

1993-01-01

The criterion for obtaining compressed chirp pulses with high signal-to-noise ratio is the shape of the power spectrum, a chirp pulse of Gaussian shaped power spectrum without modulation is needed in CPA system to get the clean compressed pulses. 4 refs., 2 figs

El futuro energético de Japón

Directory of Open Access Journals (Sweden)

María Francisca Casado

2016-05-01

Full Text Available Tras el triple desastre del 11 de marzo de 2011, Japón se encuentra en una encrucijada energética. A corto y medio plazo depende de las importaciones de combustibles fósiles para garantizar su seguridad energética, pero el largo plazo está por decidir y lo determinarán las decisiones que tome en estos años. Como consta en su Estrategia de Seguridad Nacional, para Japón la seguridad energética es una cuestión de seguridad nacional. El artículo revisa la trayectoria nuclear nipona, estudia cuáles son los factores que configuran el mercado eléctrico japonés y analiza su actual situación energética. Por otra parte, también repasa los principios que han marcado su política energética, deteniéndose a evaluar los dos últimos Planes Estratégicos de Energía –uno anterior y otro posterior a Fukushima- antes de adentrarse en el debate sobre la composición óptima del futuro mix energético para cumplir con su trilema de la seguridad energética, marcado por su compromiso con el medio ambiente.

Instrument for real-time pulse-shape analysis of slit-scan flow cytometry signals

NARCIS (Netherlands)

van Oven, C.; Aten, J. A.

1990-01-01

An instrument is described which analyses shapes of fluorescence profiles generated by particles passing through the focussed laser beam of a flow cytometer. The output signal of this pulse-shape analyzer is used as input for the signal processing electronics of a commercial flow cytometer system.

Energized Learning

Science.gov (United States)

college-level courses. The site includes lessons and activities that develop specific skills and knowledge that planning for an energy efficient future involves knowledge of science, mathematics, economics and skepticism about their predictive power. At the core of the Energized Leaning site is a interactive web-based

Energía y cambio climático

Directory of Open Access Journals (Sweden)

Wilfredo Bulege Gutiérrez

2014-06-01

Full Text Available Es claro que el crecimiento de la población, la extracción de materiales, la producción alimentaria y el incremento de energía para todas las actividades humanas nos conducen a un estado de colisión con las capacidades de la biosfera y los ecosistemas en el proceso de asegurar la provisión de bienes y servicios indispensables para la vida (1. La producción de energía convencional y contaminante es hoy una de las más graves en este escenario, tanto que la comunidad internacional y las potencias ya han empezado a dar muestras de preocupación por la seguridad energética y, con ello por la amenaza del cambio climático. En el actual cambio climático por primera vez se viene demostrando que la humanidad ha cambiado decisivamente un ciclo liberando CO2 a la atmósfera a través de la quema de combustibles fósiles y cambios en el uso del suelo por más de 500 000 años. El origen del cambio climático se remonta a dos grandes transformaciones en el uso de la energía. En primer lugar, la energía hidráulica fue reemplazada por el carbón, una fuente de energía condensada por la naturaleza a lo largo de millones de años. Fue el aprovechamiento del carbón para nuevas tecnologías lo que propulsó la revolución industrial y desató aumentos sin precedentes en la productividad. La segunda gran transformación ocurrió 150 años más tarde. El petróleo había sido una fuente de energía humana durante milenios. En China, por ejemplo, se registran pozos petroleros ya en el siglo IV. No obstante, la utilización del petróleo para los motores de combustión interna a comienzos del siglo XX marcó el inicio de una revolución en el transporte. La quema de carbón y petróleo, junto con el gas natural, ha transformado a las sociedades humanas al proveerle la energía impulsora de grandes aumentos en la riqueza y la productividad, pero también ha impulsado el cambio climático (2. La economía humana ha crecido vertiginosamente, se multiplic

Propuesta de la certificación energética, mediante simulación dinámica, como herramienta de gestión energética ISO 50001 Versus auditoria energética en edificios.

OpenAIRE

Rey Hernández, Javier María; Rey Hernández, Alberto; Velasco, Eloy; San José, Julio; Rey Martinez, Francisco Javier

2017-01-01

Producción Científica El objetivo es el estudio de la gestión energética ISO 50001, mediante las herramientas de sistema de gestión tales como la auditoría energética y compararlo con la certificación energética mediante simulación dinámica, aplicadas a un edificio universitario estándar. La metodología empleada para alcanzar unos resultados de ahorro y eficiencia energética, aplicados a un edificio universitario, pretenden servir de modelo para poder extrapolarlos a edificios que compo...

Conocimiento de Energía: Principios Esenciales y Conceptos Fundamentales para la Educación de Energía

Energy Technology Data Exchange (ETDEWEB)

None

2014-06-01

This is the Spanish version of our Energy Literacy guidebook. Esta guía presenta conceptos de energía que, cuando se entienden y se aplican, ayudan a individuos y a comunidades a tomar decisiones sobre la energía con conocimiento de causa. No es un currículo sino que ofrece un marco sobre el cual puede basarse un plan de estudios. La guía se dirige a cualquier persona que participe en la educación de energía.

Wiring of instrument for measuring pulse count of pseudocoincidences in radiation detectors

International Nuclear Information System (INIS)

Hekrdle, J.

1978-01-01

A network is described consisting of a flip-flop circuit, a pulse counter, a shift register, a gate and a clock generator. Pulses from an alpha detector are applied to the adjusting input of the control flip-flop whose output is connected to the reset input of the pulse counter and to the control input of the gate for beta pulses delayed by the shift register. The pulse counter is supplied with pulses from the clock generator output. The pulses also energize the shift register. The control flip-flop is reset by the output of the pulse counter overflow and also by the beta pulse passing through the open gate to the output terminal. (H.S.)

Advanced pulse oximeter signal processing technology compared to simple averaging. I. Effect on frequency of alarms in the operating room.

Science.gov (United States)

Rheineck-Leyssius, A T; Kalkman, C J

1999-05-01

To determine the effect of a new signal processing technique (Oxismart, Nellcor, Inc., Pleasanton, CA) on the incidence of false pulse oximeter alarms in the operating room (OR). Prospective observational study. Nonuniversity hospital. 53 ASA physical status I, II, and III consecutive patients undergoing general anesthesia with tracheal intubation. In the OR we compared the number of alarms produced by a recently developed third generation pulse oximeter (Nellcor Symphony N-3000) with Oxismart signal processing technique and a conventional pulse oximeter (Criticare 504). Three pulse oximeters were used simultaneously in each patient: a Nellcor pulse oximeter, a Criticare with the signal averaging time set at 3 seconds (Criticareaverage3s) and a similar unit with the signal averaging time set at 21 seconds (Criticareaverage21s). For each pulse oximeter, the number of false (artifact) alarms was counted. One false alarm was produced by the Nellcor (duration 55 sec) and one false alarm by the Criticareaverage21s monitor (5 sec). The incidence of false alarms was higher in Criticareaverage3s. In eight patients, Criticareaverage3s produced 20 false alarms (p signal processing compared with the Criticare monitor with the longer averaging time of 21 seconds.

Estudio de la autosuficiencia energética de una vivienda unifamiliar

OpenAIRE

Zeggaf, Itimad

2015-01-01

El título del proyecto es “Estudio de la autosuficiencia energética de una vivienda unifamiliar”. Una vivienda energéticamente autosuficiente no puede depender de ningún tipo de compañía para satisfacer las necesidades energéticas del usuario. Este proyecto estudia las necesidades energéticas de una vivienda unifamiliar habitada por 4 personas, planteando una solución que abastezca sus necesidades energéticas mediante las energías renovables. También se estudia el aprovechamiento del agua ...

Energía Undimotriz, alternativa para la producción de Energía Eléctrica en la Provincia de Santa Elena

Directory of Open Access Journals (Sweden)

Rolando Calero

2015-10-01

Full Text Available La energía undimotriz, es la energía que permite obtener electricidad a partir de energía mecánica generada por el movimiento de las olas. Es uno de los tipos de energías renovables con más recientes estudios, y presenta enormes ventajas frente a otras energías renovables debido a que se tendría mayor facilidad para predecir condiciones geológicas óptimas que permitan la mayor eficiencia en sus procesos. Debido a que es más fácil llegar a predecir condiciones óptimas de oleaje, en comparación con la obtenida con  los vientos para obtener energía eólica, donde su variabilidad es menor.En este trabajo se espera aportar y dilucidar con datosespecíficos sobre la morfología de la zonamarítima en la provincia de Santa Elena, tratando depredecir si las características propias del lugar son idóneas  para producir electricidad en base a la implementación de energíaundimotriz, como fuente renovable no convencional utilizando las tecnologías actuales para este propósito.

Importancia de las energías renovables en la seguridad energética y su relación con el crecimiento económico.

Directory of Open Access Journals (Sweden)

Lilian Paola Umbarila Valencia

2015-12-01

Full Text Available La creciente demanda de las necesidades sociales a nivel global, impulsada por los hábitos de vida y la forma en la que se organizan las regiones ha llevado al crecimiento paralelo de la industria y con ello al creciente aumento del consumo de energía. Este artículo de investigación reflexiona acerca de la relevancia que tienen las energías renovables para la seguridad energética, teniendo en cuenta la inestabilidad de los precios del petróleo y su influencia en el mercado de los hidrocarburos como fuente primaria de energía. Se evidencian los avances que han tenido las tecnologías de energías renovables a nivel global, regional y local y el rol que juegan en la independencia energética y en la mitigación del impacto ambiental. Se concluye que las naciones deben buscar la optimización de las energías renovables desde los ámbitos: local, regional y global propendiendo por su uso adecuado desde la legislación. El futuro de las energías renovables está dado por la rentabilidad, ya que para que el uso de éstas siga creciendo, deben seguir atrayendo capital lo cual significa que los inversores deben ver una rentabilidad competitiva. Otra recomendación importante es la integración de la energía renovable en la red, incluyendo fuentes de generación intermitentes e incluso imprevisibles. 

Observation of small sub-pulses out of the delayed-interference signal-wavelength converter

DEFF Research Database (Denmark)

Sakaguchi, J.; Nielsen, Mads Lønstrup; Ohira, T.

2005-01-01

The generation of small sub-pulses in the delayed-interference signal-wavelength converter (DISC), which has been studied for use in future 160-Gb/s optical time division multiplexing-wavelength division multiplexing (OTDM-WDM) communication systems, was recently predicted as a potential problem....... In this work, we have experimentally verified the generation of such pulses and its mechanism. In the experiments we used 3.8-ps-long 1.56-mu m input pulses with repetition frequencies from 12.5 to 25.0 GHz and a cross-correlation monitoring system with a time resolution of approximately 2 ps....

Temas de Física para Ingeniería: Trabajo y energía

OpenAIRE

Beléndez, Augusto; Pastor Antón, Carlos; Bernabeu, Guillermo

1988-01-01

Apuntes de Mecánica: "Trabajo y energía". Trabajo y potencia. Energía cinética, teorema de la energía cinética. Fuerzas conservativas, energía potencial. Energía potencial gravitatoria. Principio de conservación de la energía mecánica. Choques.

Ion temperature effects on magnetotail Alfvén wave propagation and electron energization: ION TEMPERATURE EFFECTS ON ALFVÉN WAVES

Energy Technology Data Exchange (ETDEWEB)

Damiano, P. A. [Princeton Center for Heliophysics, Princeton Plasma Physics Laboratory, Princeton University, Princeton New Jersey USA; Johnson, J. R. [Princeton Center for Heliophysics, Princeton Plasma Physics Laboratory, Princeton University, Princeton New Jersey USA; Chaston, C. C. [Space Sciences Laboratory, University of California, Berkeley California USA; School of Physics, University of Sydney, Sydney New South Wales Australia

2015-07-01

A new 2-D self-consistent hybrid gyrofluid-kinetic electron model in dipolar coordinates is presented and used to simulate dispersive-scale Alfvén wave pulse propagation from the equator to the ionosphere along an L = 10 magnetic field line. The model is an extension of the hybrid MHD-kinetic electron model that incorporates ion Larmor radius corrections via the kinetic fluid model of Cheng and Johnson (1999). It is found that consideration of a realistic ion to electron temperature ratio decreases the propagation time of the wave from the plasma sheet to the ionosphere by several seconds relative to a ρi=0 case (which also implies shorter timing for a substorm onset signal) and leads to significant dispersion of wave energy perpendicular to the ambient magnetic field. Additionally, ion temperature effects reduce the parallel current and electron energization all along the field line for the same magnitude perpendicular electric field perturbation.

Cosecha de energía

OpenAIRE

García Ojero, Jesús

2016-01-01

En este trabajo se analizarán los distintos métodos conocidos de extraer energía de fuentes tanto naturales como las producidas por el ser humano, entre las que se pueden distinguir las vibraciones mecánicas, gradientes de temperatura o las ondas electromagnéticas emitidas por aparatos electrónicos. Primero realizaremos una revisión bibliográfica de distintos métodos de obtención de energía a partir de vibraciones mecánicas, utilizando materiales piezoeléctricos y actuadores electromagnéticos...

Simultaneous hit finding and timing method for pulse shape analysis of drift chamber signals

Energy Technology Data Exchange (ETDEWEB)

Schaile, D; Schaile, O; Schwarz, J

1986-01-01

An algorithm for the analysis of the digitized signal waveform of drift chamber pulses is described which yields a good multihit resolution and an accurate drift time determination with little processing time. The method has been tested and evaluated with measured pulse shapes from the full size prototype of the OPAL central detector which were digitized by 100 MHz FADCs. (orig.).

Simultaneous hit finding and timing method for pulse shape analysis of drift chamber signals

Energy Technology Data Exchange (ETDEWEB)

Schaile, D; Schaile, O; Schwarz, J

1986-01-01

An algorithm for the analysis of the digitized signal waveform of drift chamber pulses is described which yields a good multihit resolution and an accurate drift time determination with little processing time. The method has been tested and evaluated with measured pulse shapes from the full size prototype of the OPAL central detector which were digitized by 100 MHz FADCs.

Studies on the transmission and processing of pulse-shaped signals from nuclear radiation detectors using methods of systems theory

International Nuclear Information System (INIS)

Spillekothen, H.G.

2007-01-01

Using methods of the systems theory of electronic communications and theoretical electrical science, this study describes the transmission of pulse-shaped signals from nuclear radiation detectors from the detector over ''electrically long lines'' (cables) to the output of the first pulse amplifier. The example of pulses from BF 3 -proportional counters shows, using the Fourier transformation, that pulses from radiation detectors contain a frequency spectrum ranging well above 10 8 Hz. If these pulses are transmitted to the first amplifier over a line length of several meters, the laws of the theory of transmission lines must be taken into account to avoid false signals caused by reflections. In the example, line equations are applied and the influence of the line and the terminating impedance is demonstrated. The influence of the frequency response ν(ω) and the phase response δ(ω) of the amplifier is also considered in the sample calculation. The methods presented make it possible to analyze and optimize the transmission and amplification of signals from radiation detectors. Close agreement emerges between empirically observed and calculated pulse shapes. (orig.)

Theoretical analysis of fluorescence signals in filamentation of femtosecond laser pulses in nitrogen molecular gas

International Nuclear Information System (INIS)

Arevalo, E.; Becker, A.

2005-01-01

We study numerically and analytically the role of the combined effect of self-focusing, geometrical focusing, and the plasma defocusing in the formation of the fluorescence signal during the filamentation of a Ti:sapphire laser pulse in nitrogen molecular gas. Results of numerical simulations are used to estimate the number of excited ions in the focal volume, which is proportional to the fluorescence signal. We find good agreement between the theoretical results and the experimental data, showing that such data can be used to get further insight into the effective focal volume during filamentation of femtosecond laser pulses in transparent media

Por uma nova ordem energética global? potencialidades e perspectivas da questão energética entre os países BRICS

Directory of Open Access Journals (Sweden)

José María Gómez

2012-12-01

Full Text Available O presente artigo propõe analisar a questão energética entre os BRICS e o potencial de rearticulação da ordem energética global que dela emerge. Para tal, realiza três movimentos. Em primeiro lugar, investiga o crescente impacto agregado dos países BRICS no cenário energético global, com vistas a analisar seu avanço em uma temática até então reduto dos países desenvolvidos. Em segundo lugar, aborda a matriz energética de cada um dos cinco países do ponto de vista de suas economias políticas e da questão da sustentabilidade. Em terceiro lugar, e com base na seção anterior, propõe mapear as áreas de conflito e de possível aproximação entre os BRICS, na tentativa de localizar as possibilidades e limites da sua cooperação energética. Com base nessa investigação, conclui que, diante das potencialidades para a cooperação entre os países, a organização de suas ofertas e demandas energéticas nacionais pode permitir ao agrupamento articular-se como um novo polo no cenário energético global.

Aplicación electrónica para el ahorro de energía eléctrica utilizando una energía alternativa

Directory of Open Access Journals (Sweden)

Juan Carlos Cruz-Ardila

2013-01-01

Full Text Available El artículo presenta un trabajo orientado a disminuir el consumo de energía eléctrica entregada por la red eléctrica convencional, a través del aprovechamiento de la energía solar fotovoltaica. Se propone el diseño de un sistema de transferencia electrónica que facilita el uso de la energía eléctrica DC proveniente del panel solar, suprimiendo de esta manera, la utilización del inversor de voltaje, comúnmente usado en este tipo de aplicaciones y que eleva el costo de utilización de la energía solar. Se da a conocer inicialmente una revisión del estado del arte, que permite contextualizar el problema resuelto a partir de una energía renovable como la fotovoltaica, destacándose que actualmente España es el país con mayor desarrollo en este tema. Luego, se muestra el desarrollo secuencial del sistema de alimentación y la transferencia electrónica, haciendo una descripción de las variables identificadas y explicación, con el uso de diagramas de flujo, del sistema embebido implementado. También se da una descripción de los dispositivos usados tal como el sensor de corriente, la regulación y la rectificación. Se muestra el esquemático de la transferencia implementada. Finalmente, se revelan los resultados y las pruebas operacionales realizadas al sistema para demostrar la funcionalidad de la aplicación electrónica en el ahorro de la energía eléctrica utilizando una energía alternativa.

Predicting blood transfusion using automated analysis of pulse oximetry signals and laboratory values.

Science.gov (United States)

Shackelford, Stacy; Yang, Shiming; Hu, Peter; Miller, Catriona; Anazodo, Amechi; Galvagno, Samuel; Wang, Yulei; Hartsky, Lauren; Fang, Raymond; Mackenzie, Colin

2015-10-01

Identification of hemorrhaging trauma patients and prediction of blood transfusion needs in near real time will expedite care of the critically injured. We hypothesized that automated analysis of pulse oximetry signals in combination with laboratory values and vital signs obtained at the time of triage would predict the need for blood transfusion with accuracy greater than that of triage vital signs or pulse oximetry analysis alone. Continuous pulse oximetry signals were recorded for directly admitted trauma patients with abnormal prehospital shock index (heart rate [HR] / systolic blood pressure) of 0.62 or greater. Predictions of blood transfusion within 24 hours were compared using Delong's method for area under the receiver operating characteristic (AUROC) curves to determine the optimal combination of triage vital signs (prehospital HR + systolic blood pressure), pulse oximetry features (40 waveform features, O2 saturation, HR), and laboratory values (hematocrit, electrolytes, bicarbonate, prothrombin time, international normalization ratio, lactate) in multivariate logistic regression models. We enrolled 1,191 patients; 339 were excluded because of incomplete data; 40 received blood within 3 hours; and 14 received massive transfusion. Triage vital signs predicted need for transfusion within 3 hours (AUROC, 0.59) and massive transfusion (AUROC, 0.70). Pulse oximetry for 15 minutes predicted transfusion more accurately than triage vital signs for both time frames (3-hour AUROC, 0.74; p = 0.004) (massive transfusion AUROC, 0.88; p transfusion prediction (3-hour AUROC, 0.84; p transfusion AUROC, 0.91; p blood transfusion during trauma resuscitation more accurately than triage vital signs or pulse oximetry analysis alone. Results suggest automated calculations from a noninvasive vital sign monitor interfaced with a point-of-care laboratory device may support clinical decisions by recognizing patients with hemorrhage sufficient to need transfusion. Epidemiologic

Apparatus and method for generating high density pulses of electrons

International Nuclear Information System (INIS)

Lee, C.; Oettinger, P.E.

1981-01-01

An apparatus and method are described for the production of high density pulses of electrons using a laser energized emitter. Caesium atoms from a low pressure vapour atmosphere are absorbed on and migrate from a metallic target rapidly heated by a laser to a high temperature. Due to this heating time being short compared with the residence time of the caesium atoms adsorbed on the target surface, copious electrons are emitted which form a high current density pulse. (U.K.)

29 CFR 1926.957 - Construction in energized substations.

Science.gov (United States)

2010-07-01

... Distribution § 1926.957 Construction in energized substations. (a) Work near energized equipment facilities. (1... lines. When it is necessary to deenergize equipment or lines for protection of employees, the... large electrical equipment, transformers, or breakers. (f) Storage. The storage requirements of § 1926...

La pobreza energética y sus implicaciones

OpenAIRE

Mikel González-Eguino

2014-01-01

32 p. El sector energético se enfrenta en las próximas décadas a tres grandes transformaciones relacionadas con el cambio climático, la seguridad de suministro y la pobreza energética. Las dos primeras han sido analizadas ampliamente. Sin embargo, la pobreza energética ha pasado más desapercibida a pesar de tener una gran influencia en la vida de millones de personas, especialmente en los países más pobres. Actualmente, 1.300 millones de personas (el 20% de la población mundial) no tienen ...

Double discharges in unipolar-pulsed dielectric barrier discharge xenon excimer lamps

International Nuclear Information System (INIS)

Liu Shuhai; Neiger, Manfred

2003-01-01

Excitation of dielectric barrier discharge xenon excimer lamps by unipolar short square pulses is studied in this paper. Two discharges with different polarity are excited by each voltage pulse (double discharge phenomenon). The primary discharge occurs at the top or at the rising flank of the applied unipolar square pulse, which is directly energized by the external circuit. The secondary discharge with the reversed polarity occurs at the falling flank or shortly after the falling flank end (zero external voltage) depending on the pulse width, which is energized by the energy stored by memory charges deposited by the primary discharge. Fast-speed ICCD imaging shows the primary discharge has a conic discharge appearance with a channel broadening on the anode side. This channel broadening increases with increasing the pulse top level. Only the anode-side surface discharge is observed in the primary discharge. The surface discharge on the cathode side which is present in bipolar sine voltage excitation is not observed. On the contrary, the secondary discharge has only the cathode-side surface discharge. The surface discharge on the anode side is not observed. The secondary discharge is much more diffuse than the primary discharge. Time-resolved emission measurement of double discharges show the secondary discharge emits more VUV xenon excimer radiation but less infrared (IR) xenon atomic emission than the primary discharge. It was found that the IR xenon atomic emission from the secondary discharge can be reduced by shortening the pulse width. The energy efficiency of unipolar-pulsed xenon excimer lamps (the overall energy efficiency of double discharges) is much higher than that obtained under bipolar sine wave excitation. The output VUV spectrum under unipolar pulse excitation is found to be identical to that under sine wave excitation and independent of injected electric power

Evaluación del potencial energético del oleaje en Madagascar

OpenAIRE

Araujo Roso, Giovanni

2017-01-01

La energía undimotriz, o energía del oleaje, es aquella que aprovecha la energía cinética de la perturbación de la superficie del mar y está considerada como una fuente de gran potencial. Las ventajas de este tipo de recurso respecto a otras energías renovables son variadas: sus eventos son predecibles con detalle, el despliegue de dispositivos tiene un impacto visual inferior a otros y es un recurso inagotable, entre otros. Por otra parte, el campo de la energía del oleaje se ...

Optimal size of stochastic Hodgkin-Huxley neuronal systems for maximal energy efficiency in coding pulse signals

Science.gov (United States)

Yu, Lianchun; Liu, Liwei

2014-03-01

The generation and conduction of action potentials (APs) represents a fundamental means of communication in the nervous system and is a metabolically expensive process. In this paper, we investigate the energy efficiency of neural systems in transferring pulse signals with APs. By analytically solving a bistable neuron model that mimics the AP generation with a particle crossing the barrier of a double well, we find the optimal number of ion channels that maximizes the energy efficiency of a neuron. We also investigate the energy efficiency of a neuron population in which the input pulse signals are represented with synchronized spikes and read out with a downstream coincidence detector neuron. We find an optimal number of neurons in neuron population, as well as the number of ion channels in each neuron that maximizes the energy efficiency. The energy efficiency also depends on the characters of the input signals, e.g., the pulse strength and the interpulse intervals. These results are confirmed by computer simulation of the stochastic Hodgkin-Huxley model with a detailed description of the ion channel random gating. We argue that the tradeoff between signal transmission reliability and energy cost may influence the size of the neural systems when energy use is constrained.

Ponte en onda: prende la energía limpia, (Spanish) Get Current

Energy Technology Data Exchange (ETDEWEB)

None

2015-05-01

Cambiar a tecnologías de energía limpia significa que fortalecemos la economía y protegemos al medio ambiente. Este libreto de actividades educativas para todas las edades promueve el uso consciente de la energía, con datos de distintas formas de energía aplicables y una variedad de rompecabezas y crucigramas en temas energéticos.

La energía que requiere nuestro territorio

OpenAIRE

Pacheco, Máximo

2015-01-01

En esta columna de opinión, el Ministro de Energía nos invita a enfrentarnos a un problema crucial para un país como Chile: sin energía a precios razonables, esa desigualdad social que tanto criticamos terminará por expandirse. Pero a la vez el Ministro nos invita a cambiar el foco, y así «transformar la energía en un ecualizador de la igualdad», con un Estado más activo en la solución de esta crucial problemática. In this op-ed piece, the Minister of Energy invites us to face a crucial pr...

Nonlinear Pulse Shaping in Fibres for Pulse Generation and Optical Processing

Directory of Open Access Journals (Sweden)

Sonia Boscolo

2012-01-01

Full Text Available The development of new all-optical technologies for data processing and signal manipulation is a field of growing importance with a strong potential for numerous applications in diverse areas of modern science. Nonlinear phenomena occurring in optical fibres have many attractive features and great, but not yet fully explored, potential in signal processing. Here, we review recent progress on the use of fibre nonlinearities for the generation and shaping of optical pulses and on the applications of advanced pulse shapes in all-optical signal processing. Amongst other topics, we will discuss ultrahigh repetition rate pulse sources, the generation of parabolic shaped pulses in active and passive fibres, the generation of pulses with triangular temporal profiles, and coherent supercontinuum sources. The signal processing applications will span optical regeneration, linear distortion compensation, optical decision at the receiver in optical communication systems, spectral and temporal signal doubling, and frequency conversion.

Neutron-Gamma Pulse Shape Discrimination With Ne-213 Liquid Scintillator By Using Digital Signal Processing Combined With Similarity Method

International Nuclear Information System (INIS)

Mardiyanto

2008-01-01

Neutron-Gamma Pulse Shape Discrimination with a NE-213 Liquid Scintillator by Using Digital Signal Processing Combined with Similarity Method. Measurement of mixed neutron-gamma radiation is difficult because a nuclear detector is usually sensitive to both radiations. A new attempt of neutron-gamma pulse shape discrimination for a NE-213 liquid scintillator is presented by using digital signal processing combined with an off-line similarity method. The output pulse shapes are digitized with a high speed digital oscilloscope. The n-γ discrimination is done by calculating the index of each pulse shape, which is determined by the similarity method, and then fusing it with its corresponding pulse height. Preliminary results demonstrate good separation of neutron and gamma-ray signals from a NE-213 scintillator with a simple digital system. The results were better than those with a conventional rise time method. Figure of Merit is used to determine the quality of discrimination. The figure of merit of the discrimination using digital signal processing combined with off-line similarity method are 1.9; 1.7; 1.1; 1.1; and 0.8; on the other hand by using conventional method the rise time are 0.9; 0.9; 0.9; 0.7; and 0.4 for the equivalent electron energy of 800; 278; 139; 69; and 30 keV. (author)

The influence of stellate ganglion transcutaneous electrical nerve stimulation on signal quality of pulse oximetry in prehospital trauma care.

Science.gov (United States)

Barker, Renate; Lang, Thomas; Hager, Helmut; Steinlechner, Barbara; Hoerauf, Klaus; Zimpfer, Michael; Kober, Alexander

2007-05-01

Accurate monitoring of the peripheral arterial oxygen saturation has become an important tool in the prehospital emergency medicine. This monitoring requires an adequate plethysmographic pulsation. Signal quality is diminished by cold ambient temperature due to vasoconstriction. Blockade of the stellate ganglion can improve peripheral vascular perfusion and can be achieved by direct injection or transcutaneous electrical nerve stimulation (TENS) stimulation. We evaluated whether TENS on the stellate ganglion would reduce vasoconstriction and thereby improve signal detection quality of peripheral pulse oximetry. In our study, 53 patients with minor trauma who required transport to the hospital were enrolled. We recorded vital signs, including core and skin temperature before and after transport to the hospital. Pulse oximetry sensors were attached to the patient's second finger on both hands. TENS of the stellate ganglion was started on one side after the beginning of the transport. Pulse oximeter alerts, due to poor signal detection, were recorded for each side separately. On the hand treated with TENS we detected a significant reduction of alerts compared to the other side (mean alerts TENS 3.1 [1-15] versus control side 8.8 [1-28] P signal quality of pulse oximeters in the prehospital setting.

The neutrino horn 300 kiloampere pulsed power supply at Brookhaven National Laboratory

International Nuclear Information System (INIS)

Sandberg, J.; Smith, G.A.; Carroll, A.S.

1987-01-01

A 300 Kiloampere pulsed power system used to energize the Brookhaven focusing neutrino horn is described. The constant current switching section, coaxial power feed and low level control system are presented. Calculations determining system performance are compared with measured values. Plans for future systems are discussed

Electronic constant current and current pulse signal generator for nuclear instrumentation testing

International Nuclear Information System (INIS)

Brown, R.A.

1994-01-01

Circuitry is described for testing the ability of an intermediate range nuclear instrument to detect and measure a constant current and a periodic current pulse. The invention simulates the resistance and capacitance of the signal connection of a nuclear instrument ion chamber detector and interconnecting cable. An LED flasher/oscillator illuminates an LED at a periodic rate established by a timing capacitor and circuitry internal to the flasher/oscillator. When the LED is on, a periodic current pulse is applied to the instrument. When the LED is off, a constant current is applied. An inductor opposes battery current flow when the LED is on. 1 figures

La energía humana el esfuerzo físico

Directory of Open Access Journals (Sweden)

Luis Suárez Flórez

1991-01-01

Full Text Available Se llama la atención sobre la energía humana, su importancia como elemento de productividad y como principio ó quizás como fin de la actividad deportiva. Se estudia el máximo esfuerzo físico, así como también algunos conceptos acerca de la energía aeróbica y la energía anaeróbica.

Determination of the X, Y coordinates of a pulsed ultrasonic source of signals

International Nuclear Information System (INIS)

Sokolov, B.V.; Shemyakin, V.V.

1975-01-01

A range of problems in predicting the emergency state of large-scale vessel housings are determined for subsequent solution involving acoustic emission phenomena. The authors specify the position of a given problem and present substantial grounds for selecting the minimum number of group signal receivers for unambiguous calculation of the location of the source. Relationships are obtained between X, Y - the coordinates of the pulse signal source - and experimentally measured time differences in recording of signals by group receivers. A criterion is given for selecting the true signal group combination when the receivers simultaneously record waves from several sources. Specific suggestions are made regarding the experimental information to be stored in a central computer for subsequent processing [ru

La energía minihidráulica en los planes de fomento de las energías renovables en España

OpenAIRE

Espejo Marín, Cayetano; García Marín, Ramón; Aparicio Guerrero, Ana Eulalia

2016-01-01

La energía minihidráulica incluye las centrales con una potencia instalada de hasta 10 megavatios. Esta tecnología de producción energética se ha incluido en los Planes de Fomento de las Energías Renovables promovidos por los Gobiernos de España desde finales de los años noventa a la actualidad. En esta aportación se analizan los objetivos de potencia a instalar en cada Comunidad Autónoma durante el periodo de vigencia de cada Plan, las barreras con las que se encuentra el sector para el desa...

La educación energética una prioridad para el milenio

Directory of Open Access Journals (Sweden)

Johnn Edgar Castro

2015-01-01

Full Text Available Este articulo plantea la necesidad  de reflexionar y trabajar en el desarrollo de propuestas sobre educación energética, desde cuatro enfoques fundamentalmente: la primera de ellas  es la inevitable dependencia de las sociedades humanas de las fuentes de energía; el ahorro energético; el agotamiento de las fuentes de energía y por ultimo las consecuencias sobre el medioambiente

Fiber Optical Parametric Chirped Pulse Amplification of Sub-Picosecond Pulses

DEFF Research Database (Denmark)

Cristofori, Valentina; Lali-Dastjerdi, Zohreh; Da Ros, Francesco

2013-01-01

We demonstrate experimentally, for the first time to our knowledge, fiber optical parametric chirped pulse amplification of 400-fs pulses. The 400-fs signal is stretched, amplified by 26 dB and compressed back to 500 fs.......We demonstrate experimentally, for the first time to our knowledge, fiber optical parametric chirped pulse amplification of 400-fs pulses. The 400-fs signal is stretched, amplified by 26 dB and compressed back to 500 fs....

Photon statistics of pulse-pumped four-wave mixing in fiber with weak signal injection

Science.gov (United States)

Nan-Nan, Liu; Yu-Hong, Liu; Jia-Min, Li; Xiao-Ying, Li

2016-07-01

We study the photon statistics of pulse-pumped four-wave mixing in fibers with weak coherent signal injection by measuring the intensity correlation functions of individual signal and idler fields. The experimental results show that the intensity correlation function of individual signal (idler) field decreases with the intensity of signal injection. After applying narrow band filter in signal (idler) band, the value of decreases from 1.9 ± 0.02 (1.9 ± 0.02) to 1.03 ± 0.02 (1.05 ± 0.02) when the intensity of signal injection varies from 0 to 120 photons/pulse. The results indicate that the photon statistics changes from Bose-Einstein distribution to Poisson distribution. We calculate the intensity correlation functions by using the multi-mode theory of four-wave mixing in fibers. The theoretical curves well fit the experimental results. Our investigation will be useful for mitigating the crosstalk between quantum and classical channels in a dense wavelength division multiplexing network. Project supported by the National Natural Science Foundation of China (Grant No. 11527808), the State Key Development Program for Basic Research of China (Grant No. 2014CB340103), the Specialized Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20120032110055), the Natural Science Foundation of Tianjin, China (Grant No. 14JCQNJC02300), the Program for Changjiang Scholars and Innovative Research Team in University, China, and the Program of Introducing Talents of Discipline to Universities, China (Grant No. B07014).

30 CFR 77.704-2 - Repairs to energized high-voltage lines.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Repairs to energized high-voltage lines. 77.704... UNDERGROUND COAL MINES Grounding § 77.704-2 Repairs to energized high-voltage lines. An energized high-voltage... repairs will be performed on power circuits with a phase-to-phase nominal voltage no greater than 15,000...

Ahorre Energía: Consejos para ahorro dinero y energía en su hogar (Spanish Brochure), Energy Saver Guide

Energy Technology Data Exchange (ETDEWEB)

None

2017-11-01

La versión en castellano de la guía del Departamento de Energía de los Estados Unidos que ayuda a consumidores a ahorrar energía y dinero en su hogar y en las carreteras. The Spanish-language version of U.S. Department of Energy's Energy Saver consumer guide to saving energy and money at home and on the road.

Repetitively pulsed capacitor bank for the dense-plasma focus

International Nuclear Information System (INIS)

Zucker, O.; Bostick, W.; Gullickson, R.; Long, J.; Luce, J.; Sahlin, H.

1975-12-01

This report describes a 1 pulse per second capacitor bank designed to energize a dense-plasma focus (DPF). The DPF is a neutron source capable (with moderate scaling) of delivering a minimum of 10 15 neutrons per pulse or neutron flux of 2 x 10 13 N/cm 2 .s. The average power consumption, which has become a major issue due to the energy crisis, is analyzed with respect to other plasma devices and is shown to be highly favorable. This small source size high flux neutron source could be extemely useful to qualify fission reactor material irradiation results for fusion reactor design

Repetitively pulsed capacitor bank for the dense-plasma focus

International Nuclear Information System (INIS)

Zucker, O.; Bostick, W.; Gullickson, R.; Long, J.; Luce, J.; Sahlin, H.

1976-01-01

This report describes a 1 pulse per second capacitor bank designed to energize a dense-plasma focus (DPF). The DPF is a neutron source capable (with moderate scaling) of delivering a minimum of 10 15 neutrons per pulse or neutron flux of 2 x 10 13 N/cm 2 . s. The average power consumption, which has become a major issue due to the energy crisis, is analyzed with respect to other plasma devices and is shown to be highly favorable. This small source size high flux neutron source could be extremely useful to qualify fission reactor material irradiation results for fusion reactor design

Energía Minihidráulica

OpenAIRE

Mancebo Piqueras, José Antonio; Adrada Guerra, Teodoro; Martinez, Carmen

2013-01-01

La energía basada en turbinas hidráulicas de reducida potencia es, a menudo, un ejemplo- modelo dentro del campo de las energías renovables desde su aparición a finales del S. XIX, aunque los ingenios precursores surgen mucho antes. Entre los testimonios más antiguos destacan la saqia o rueda persa y la rueda hidráulica romana que había sido previamente implementada en Extremo Oriente, y que después llega a Europa a través de Egipto. Más tarde, durante la Edad Media y el Renacimiento, se gene...

Optimal filter bandwidth for pulse oximetry

Science.gov (United States)

Stuban, Norbert; Niwayama, Masatsugu

2012-10-01

Pulse oximeters contain one or more signal filtering stages between the photodiode and microcontroller. These filters are responsible for removing the noise while retaining the useful frequency components of the signal, thus improving the signal-to-noise ratio. The corner frequencies of these filters affect not only the noise level, but also the shape of the pulse signal. Narrow filter bandwidth effectively suppresses the noise; however, at the same time, it distorts the useful signal components by decreasing the harmonic content. In this paper, we investigated the influence of the filter bandwidth on the accuracy of pulse oximeters. We used a pulse oximeter tester device to produce stable, repetitive pulse waves with digitally adjustable R ratio and heart rate. We built a pulse oximeter and attached it to the tester device. The pulse oximeter digitized the current of its photodiode directly, without any analog signal conditioning. We varied the corner frequency of the low-pass filter in the pulse oximeter in the range of 0.66-15 Hz by software. For the tester device, the R ratio was set to R = 1.00, and the R ratio deviation measured by the pulse oximeter was monitored as a function of the corner frequency of the low-pass filter. The results revealed that lowering the corner frequency of the low-pass filter did not decrease the accuracy of the oxygen level measurements. The lowest possible value of the corner frequency of the low-pass filter is the fundamental frequency of the pulse signal. We concluded that the harmonics of the pulse signal do not contribute to the accuracy of pulse oximetry. The results achieved by the pulse oximeter tester were verified by human experiments, performed on five healthy subjects. The results of the human measurements confirmed that filtering out the harmonics of the pulse signal does not degrade the accuracy of pulse oximetry.

Som Energia: sostenibilitat energètica i cooperativisme

OpenAIRE

Duran i Grant, Alexandre; Huijink, Gijsbert; Roselló, Marc

2013-01-01

La cooperativa Som Energia és una organització innovadora en el sector energètic a casa nostra. Proposa una forma de fer diferent de la de les empreses tradicionals del sector: ven energia renovable certificada, no té ànim de lucre i busca el bé comú. La proposta treballa per la sostenibilitat energètica.

Sistema de Aprovechamiento de la Energía de las Olas del Mar

OpenAIRE

Pi Amorós, Gabriel

2010-01-01

Este documento describe un sistema de aprovechamiento de la energía transportada por el oleaje o energía undimotriz. El sistema no transformará la energía únicamente en electricidad si no que aprovecha dicha electricidad para producir hidrógeno mediante el proceso de la electrólisis del agua de mar. Es decir, el sistema propuesto es un sistema de generación de hidrógeno de origen renovable a partir de una fuente de energía renovable, la energía undimotriz. Las característica...

Pulse coded safety logic for PFBR

International Nuclear Information System (INIS)

Anwer, Md. Najam; Satheesh, N.; Nagaraj, C.P.; Krishnakumar, B.

2002-01-01

Full text: Reactor safety logic is designed to initiate safety action against design basis events. The reactor is shutdown by de-energizing electromagnets and dropping the absorber rods under gravity. In prototype fast breeder reactor (PFBR), shutdown is affected by two independent shutdown systems, viz., control and safety rod drive mechanism (CSRDM) and diverse safety rod drive mechanism (DSRDM). Two separate safety logics are proposed for CSRDM and DSRDM, i.e. solid state logic with on-line fine impulse test (FIT) for CSRDM and pulse coded safety logic (PCSL) for DSRDM. The PCSL primarily utilizes the fact that the vast majority of faults in the logic circuitry result in static conditions at the output. It is arranged such that the presence of pulses are required to hold the shutdown actuators and any DC logic state, either logic 0 or logic 1 releases them. It is a dynamic, self-testing logic and used in a number of reactors. This paper describes the principle of operation of PCSL, its advantages, the concept of guard line logic (GLL), detection of stuck at 0 and stuck at 1 faults, fail safe and diversity features. The implementation of PCSL using Altera Max+Plus II software for PFBR trip signals and the results of simulation are discussed. This paper also describes a test jig using 80186 based system for testing PCSL for various input parameter's combinations and monitoring the outputs

Effect of laser pulse energies in laser induced breakdown spectroscopy in double-pulse configuration

International Nuclear Information System (INIS)

Benedetti, P.A.; Cristoforetti, G.; Legnaioli, S.; Palleschi, V.; Pardini, L.; Salvetti, A.; Tognoni, E.

2005-01-01

In this paper, the effect of laser pulse energy on double-pulse laser induced breakdown spectroscopy signal is studied. In particular, the energy of the first pulse has been changed, while the second pulse energy is held fixed. A systematic study of the laser induced breakdown spectroscopy signal dependence on the interpulse delay is performed, and the results are compared with the ones obtained with a single laser pulse of energy corresponding to the sum of the two pulses. At the same time, the crater formed at the target surface is studied by video-confocal microscopy, and the variation in crater dimensions is correlated to the enhancement of the laser induced breakdown spectroscopy signal. The results obtained are consistent with the interpretation of the double-pulse laser induced breakdown spectroscopy signal enhancement in terms of the changes in ambient gas pressure produced by the shock wave induced by the first laser pulse

Medidas de mejora de la eficiencia energética de edificios residenciales

OpenAIRE

Hernández Sánchez, Juan Manuel

2012-01-01

El parque de edificios residenciales existente tiene un potencial muy grande para mejorar la eficiencia energética a corto y medio plazo, debido al gran número de viviendas existentes y a su larga vida residual. Los factores que influyen directamente en el consumo energético y en las emisiones asociadas a los edificios residenciales son: la envolvente térmica, la eficiencia energética de los equipos, las fuentes energéticas utilizadas y el comportamiento de los usuarios. Las barreras qu...

[Low-frequency pulsed electromagnetic fields promotes rat osteoblast differentiation in vitro through cAMP/PKA signal pathway].

Science.gov (United States)

Fang, Qing-Qing; Li, Zhi-Zhong; Zhou, Jian; Shi, Wen-Gui; Yan, Juan-Li; Xie, Yan-Fang; Chen, Ke-Ming

2016-11-20

To study whether low-frequency pulsed electromagnetic fields promotes the differentiation of cultured rat osteoblasts through the cAMP/PKA signal pathway. Rat calvarial osteoblasts isolated by enzyme digestion were exposed to 50 Hz 0.6 mT low-frequency pulsed electromagnetic field for varying lengths of time, and the concentration of cAMP and levels of phosphorylated PKA in the cells were assayed. In cells treated with DDA to inhibit the activity of adenylate cyclase, the changes of ALP activity and transcription of osteogenic gene were detected after exposure to low-frequency pulsed electromagnetic field. The changes of osteogenic gene transcription and protein expression were tested in the osteoblasts pretreated with KT5720 in response to low-frequency pulsed electromagnetic field exposure. The intracellular cAMP concentration in the cells increased significantly at 20 min during exposure to low-frequency pulsed electromagnetic field, began to decrease at 40 min during the exposure, and increased again after a 2-h exposure; the same pattern of variation was also observed in p-PKA level. Application of DDA and KT5720 pretreatment both suppressed the increase in ALP activity and osteogenic gene transcription induced by electromagnetic field exposure. Low- frequency pulsed electromagnetic field exposure improves the differentiation of cultured rat osteoblasts by activating cAMP/PKA signal pathway.

El hidrógeno y la energía

OpenAIRE

Aurelio Mendoza Medellín

2006-01-01

El hidrógeno es el elemento más simple, pero es fundamental para la vida. En el futuro sustituirá a los combustibles fósiles como fuente de energía para las máquinas hechas por el hombre. Hoy en día su uso es muy caro, pero ya existen motores que trabajan quemando este gas. En el sol la fusión de hidrógeno libera cantidades inconmensurables de energía, que en parte es captada por los cloroplastos, que la transforman en la energía química contenida en los carbohidratos resultantes de la fotosí...

El hidrógeno y la energía

OpenAIRE

Aurelio Mendoza Medellín

2006-01-01

El hidrógeno es el elemento más simple, pero es fundamental para la vida. En el futuro sustituirá a los combustibles fósiles como fuente de energía para las máquinas hechas por el hombre. Hoy en día su uso es muy caro, pero ya existen motores que trabajan quemando este gas. En el sol la fusión de hidrógeno libera cantidades inconmensurables de energía, que en parte es captada por los cloroplastos, que la transforman en la energía química contenida en los carbohidratos resultantes ...

Final Technical Report, reEnergize Program

Energy Technology Data Exchange (ETDEWEB)

Wamstad-Evans, Kristi [City of Omaha; Williams, Eric [City of Omaha; Kubicek, Jason [City of Omaha

2013-12-27

The reEnergize Program helped to build a market for residential and commercial energy evaluations and upgrades. The program provided incentives to encourage participants to save energy, save money, and make their homes and businesses more safe, healthy, and comfortable. As part of the Better Buildings Neighborhood Program (BBNP), the successful investment of this $10 million grant toward market development was the first grant funding collaboration between the cities of Omaha and Lincoln. Through more than three years of work, thousands of participants, contractors, and community members worked together to make the reEnergize Program a demonstration of how to “Build Energy Smart Communities.”

Temporal analysis of reflected optical signals for short pulse laser interaction with nonhomogeneous tissue phantoms

International Nuclear Information System (INIS)

Trivedi, Ashish; Basu, Soumyadipta; Mitra, Kunal

2005-01-01

The use of short pulse laser for minimally invasive detection scheme has become an indispensable tool in the technological arsenal of modern medicine and biomedical engineering. In this work, a time-resolved technique has been used to detect tumors/inhomogeneities in tissues by measuring transmitted and reflected scattered temporal optical signals when a short pulse laser source is incident on tissue phantoms. A parametric study involving different scattering and absorption coefficients of tissue phantoms and inhomogeneities, size of inhomogeneity as well as the detector position is performed. The experimental measurements are validated with a numerical solution of the transient radiative transport equation obtained by using discrete ordinates method. Thus, both simultaneous experimental and numerical studies are critical for predicting the optical properties of tissues and inhomogeneities from temporal scattered optical signal measurements

30 CFR 75.705-2 - Repairs to energized surface high-voltage lines.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Repairs to energized surface high-voltage lines... Repairs to energized surface high-voltage lines. An energized high-voltage surface line may be repaired... on power circuits with a phase-to-phase nominal voltage no greater than 15,000 volts; (3) Such...

Situación actual del sector energético en España

Directory of Open Access Journals (Sweden)

Carlos J. Pardo Abad

2001-01-01

Full Text Available La energía es un sector clave de la economía española y está presente en todos los procesos productivos. El artículo analiza al sector en los últimos años con datos procedentes de varios organismos públicos, referidos tanto al balance energético general como a los sectores energéticos, las energías renovables, la política energética y las relaciones entre energía y medio ambiente. Características básicas del sector en nuestro país son el incremento del consumo de energía, la progresiva liberalización y las grandes inversiones en energías renovables, sobre todo la eólica. Energy is a key sector of the Spanish economy and it is in all productivo processes.This article analyses the sector in the last fewyears with data from some public agencies, referred to the power balance as well as to nuclear power, coal, oil, natural gas, renewable energies, power policy and the relationship between energy and environment. The main eatures of energy in Spain are the increase of consumption, the growing liberation and the big investments in renewable energies, above all the eolic one.

Producción, Reservas y Sostenibilidad de la Energía en Venezuela

Directory of Open Access Journals (Sweden)

Juan Carlos Rojas-Zerpa

2015-06-01

Full Text Available El propósito del presente trabajo está relacionado con la evaluación de los recursos energéticos de Venezuela y su posicionamiento estratégico mundial, referido principalmente a la producción y consumo de energía primaria y reservas. Así mismo se han evaluado los recursos energéticos renovables con la finalidad de identificar oportunidades para el desarrollo de la energía sostenible. Los resultados indican que Venezuela posee recursos fósiles para más de 130 años de explotación, lo cual lo convierte en una potencia energética relevante en el contexto mundial. La potencialidad aprovechable de las energías renovables duplicó la producción de recursos fósiles en 2011. En la actualidad, el aprovechamiento de estas fuentes es inferior al 2 % del total disponible, lo que deja abierto un amplio rango de posibilidades para la diversificación de la matriz energética nacional mediante tecnologías limpias o sostenibles

Cálculo del balance de energía para higuerilla (Ricinus communis L. desde las etapas de producción en campo hasta el valor energético de cada componente de la planta

Directory of Open Access Journals (Sweden)

Hipólito Ortíz-Laurel

2017-01-01

Full Text Available Introducción : Pruebas de balance de energía permiten redirigir los insumos desde las etapas de producción de un cultivo, e igualmente, precesar la cantidad de energía utilizada para cada proceso y así, verificar la eficiencia al transformar la energía contenida en el cultivo cuando debe cumplir con una función deseada. Método : la planta de higuerilla (Ricinus communis L. con propósitos de cultivo energético fue sembrada en campo y sometida a procesos de mantenimiento de l cultivo y en la cosecha, la planta completa fue colectada para análisis energético, donde cada una de sus partes inclu i das las semillas fueron evaluadas en función de su contenido de energía. Así, para determinar el balance de energía; los valores de la energía biológica de la planta fueron comparados con la energía aplicada en cada uno de los procesos técnicos y físicos para la producción del cult i vo y en su procesamiento . Resultados : La energía aplicada para producir el cultivo r esulta un 28% superior a la energía a obtener de la planta. Asimismo, la biomasa de la planta completa de higuerilla, sin contar las semillas genera el doble de energía comparado con el aceite de las semillas, por lo que, conviene utilizar toda la planta e n términos de energía . Conclusión : Es recomendable utilizar el aceite de las seillas como biomaterial, ya que el b a lance es positivo en un 15%.

Panorama energético mundial y argentino

OpenAIRE

Guadagni, Alieto

2007-01-01

Estamos transitando aceleradamente de una etapa caracterizada por energía abundante, barata y exportada a otra etapa signada por la escasez, el alto costo y las importaciones. Esta es la triple tenaza energética que enfrenta la Argentina. Los actuales precios del petróleo están impulsando la producción de biocombustibles (biodiesel y etanol) en Brasil, la Unión Europea y los Estados Unidos, pero también muchos otros países como el nuestro. Se estima que su participación en el consumo mundi...

El hidrógeno y la energía

Directory of Open Access Journals (Sweden)

Aurelio Mendoza Medellín

2006-01-01

Full Text Available El hidrógeno es el elemento más simple, pero es fundamental para la vida. En el futuro sustituirá a los combustibles fósiles como fuente de energía para las máquinas hechas por el hombre. Hoy en día su uso es muy caro, pero ya existen motores que trabajan quemando este gas. En el sol la fusión de hidrógeno libera cantidades inconmensurables de energía, que en parte es captada por los cloroplastos, que la transforman en la energía química contenida en los carbohidratos resultantes de la fotosíntesis. Esto implica la transferencia del hidrógeno del agua al dióxido de carbono. Los animales liberan la energía de los combustibles biológicos revirtiendo dicha reacción a través del metabolismo oxidativo, la cadena respiratoria y la fosforilación oxidativa. El hidrógeno es vital para producir ATP y por lo tanto para la vida.

Sleep disordered breathing analysis in a general population using standard pulse oximeter signals.

Science.gov (United States)

Barak-Shinar, Deganit; Amos, Yariv; Bogan, Richard K

2013-09-01

Obstructive sleep apnea reported as the apnea-hypopnea index (AHI) is usually measured in sleep laboratories using a high number of electrodes connected to the patient's body. In this study, we examined the use of a standard pulse oximeter system with an automated analysis based on the photoplethysmograph (PPG) signal for the diagnosis of sleep disordered breathing. Using a standard and simple device with high accuracy might provide a convenient diagnostic or screening solution for patient evaluation at home or in other out of center testing environments. The study included 140 consecutive patients that were referred routinely to a sleep laboratory [SleepMed Inc.] for the diagnosis of sleep disordered breathing. Each patient underwent an overnight polysomnography (PSG) study according to AASM guidelines in an AASM-accredited sleep laboratory. The automatic analysis is based on photoplethysmographic and saturation signals only. Those two signals were recorded for the entire night as part of the full overnight PSG sleep study. The AHI calculated from the PPG analysis is compared to the AHI calculated from the manual scoring gold standard full PSG. The AHI and total respiratory events measured by the pulse oximeter analysis correlated very well with the corresponding results obtained by the gold standard full PSG. The sensitivity and specificity of AHI = or > 5 and 15 levels measured by the analysis are both above 90 %. The sensitivity and positive predictive value for the detection of respiratory event are both above 84 %. The tested system in this study yielded an acceptable result of sleep disordered breathing compared to the gold standard PSG in patients with moderate to severe sleep apnea. Accordingly and given the convenience and simplicity of the standard pulse oximeter device, the new system can be considered suitable for home and ambulatory diagnosis or screening of sleep disordered breathing patients.

Signal-Pressure Curves of Cascaded Four-Wave Mixing in Gas-Filled Capillary by fs Pulses

International Nuclear Information System (INIS)

Chen Baozhen; Huang Zuqia

2005-01-01

The theoretical framework for the cascaded four waves mixing (CFWM) in gas-filled capillary by fs pulses is constructed. Based on the theoretical framework, the signal-pressure curves (SPC) of the CFWM in gas-filled capillary by fs pulses are calculated. With a comparison between the theoretical and experimental SPC we have discussed the influence of the walk-off and phase modulation on the SPC. At the same time, we have discussed the possible origin of the first three peaks of the SPC.

Control Operator for the Two-Dimensional Energized Wave Equation

Directory of Open Access Journals (Sweden)

Sunday Augustus REJU

2006-07-01

Full Text Available This paper studies the analytical model for the construction of the two-dimensional Energized wave equation. The control operator is given in term of space and time t independent variables. The integral quadratic objective cost functional is subject to the constraint of two-dimensional Energized diffusion, Heat and a source. The operator that shall be obtained extends the Conjugate Gradient method (ECGM as developed by Hestenes et al (1952, [1]. The new operator enables the computation of the penalty cost, optimal controls and state trajectories of the two-dimensional energized wave equation when apply to the Conjugate Gradient methods in (Waziri & Reju, LEJPT & LJS, Issues 9, 2006, [2-4] to appear in this series.

La Demanda Residencial por Energía Eléctrica en Chile

OpenAIRE

Claudio A Agostini; Cecilia Plottier; Eduardo Saavedra

2011-01-01

En un contexto de demanda creciente y oferta estocástica de energía en Chile se hace necesario conocer a cabalidad los determinantes de la demanda por energía eléctrica de los hogares - en particular su elasticidad precio - para así utilizar mecanismos de flexibilización de precios con miras a reducir posibles déficits de energía. Este trabajo estima la demanda de energía eléctrica residencial usando información de la Encuesta de Caracterización Socioeconómica Nacional (CASEN) 2006, siendo in...

Acoustic signal generation in excised muscle by pulsed proton beam irradiation and the possibility of its clinical application to radiation therapy

International Nuclear Information System (INIS)

Hayakawa, Yoshinori; Tada, Junichiro; Inada, Tetsuo; Kitagawa, Toshio; Wagai, Toshio; Yoshioka, Katsuya.

1989-01-01

Acoustic signals generated in liquids and in metals by pulsed proton beam are thought to be thermal shock wave due to localized energy deposition of incident protons. Thus the intensity of generated acoustic signals is almost proportional to the energy deposited at the region. This suggests the possibility for measuring spatial distribution of energy deposition of proton beam using the acoustic method. In proton beam radiation therapy, treatment planning is developed from data of X-ray computer tomography which reflects the information on the electron density distribution in the patient's body. Ensuring the agreement of the dose distribution in the patient with the planned one, however, is difficult. It is expected that the acoustic method can provide a useful tool for this purpose. The pulsed proton beam of 50ns in pulse width is used for cancer therapy at the University of Tsukuba. A hydrophone is used to detect acoustic signals generated by pulsed proton beam. Detected signals are amplified ten thousand times before being averaged and analyzed by digital oscilloscope. Measurements made suggest that the method could be useful for radiation therapy. (N.K.)

Synchronization of femtosecond laser pulses and RF signal by using a Sagnac loop Mach-Zehnder interferometer

International Nuclear Information System (INIS)

Dai Hui; Hajima, Ryoichi

2008-11-01

For future advanced energy recovery linac to generate femtosecond X-ray pulses, precise synchronization between sub-systems is highly desired. Typical synchronization methods based on direct photo detection are limited by detector nonlinearities, which lead to amplitude-to-phase conversion and introduce excess timing jitter. In this paper, we experimentally demonstrate an optical-electronic mixed phase lock loop to synchronize the RF signal and laser pulses. In this synchronism setup, a Sagnac-loop Mach-Zehnder interferometer has been used to suppress the excess noise of direct photo detection. This scheme transfers the timing information into a intensity imbalance between the two output beams of the interferometer. As experimental demonstration, the single side-band phase noise of RF signal from the VCO is locked to the mode-locked Ti:Sapphire laser in the spectrum covering the range of 10 kHz to 1 MHz. This synchronization scheme greatly reduces the phase noise and timing jitter of the RF signal. (author)

Pulse-coupled neural nets: translation, rotation, scale, distortion, and intensity signal invariance for images.

Science.gov (United States)

Johnson, J L

1994-09-10

The linking-field neural network model of Eckhorn et al. [Neural Comput. 2, 293-307 (1990)] was introduced to explain the experimentally observed synchronous activity among neural assemblies in the cat cortex induced by feature-dependent visual activity. The model produces synchronous bursts of pulses from neurons with similar activity, effectively grouping them by phase and pulse frequency. It gives a basic new function: grouping by similarity. The synchronous bursts are obtained in the limit of strong linking strengths. The linking-field model in the limit of moderate-to-weak linking characterized by few if any multiple bursts is investigated. In this limit dynamic, locally periodic traveling waves exist whose time signal encodes the geometrical structure of a two-dimensional input image. The signal can be made insensitive to translation, scale, rotation, distortion, and intensity. The waves transmit information beyond the physical interconnect distance. The model is implemented in an optical hybrid demonstration system. Results of the simulations and the optical system are presented.

Ahorre Energía: Consejos sobre el ahorro de dinero y energía en el hogar (Spanish Brochure), Energy Savers Guide

Energy Technology Data Exchange (ETDEWEB)

None

2014-09-01

La versión en castellano de la guía del Departamento de Energía de los Estados Unidos que ayuda a consumidores a ahorrar energía y dinero en el hogar y en las carreteras. The Spanish-language version of U.S. Department of Energy's consumer guide to saving energy and money at home and on the road.

Speckle noise reduction technique for Lidar echo signal based on self-adaptive pulse-matching independent component analysis

Science.gov (United States)

Xu, Fan; Wang, Jiaxing; Zhu, Daiyin; Tu, Qi

2018-04-01

Speckle noise has always been a particularly tricky problem in improving the ranging capability and accuracy of Lidar system especially in harsh environment. Currently, effective speckle de-noising techniques are extremely scarce and should be further developed. In this study, a speckle noise reduction technique has been proposed based on independent component analysis (ICA). Since normally few changes happen in the shape of laser pulse itself, the authors employed the laser source as a reference pulse and executed the ICA decomposition to find the optimal matching position. In order to achieve the self-adaptability of algorithm, local Mean Square Error (MSE) has been defined as an appropriate criterion for investigating the iteration results. The obtained experimental results demonstrated that the self-adaptive pulse-matching ICA (PM-ICA) method could effectively decrease the speckle noise and recover the useful Lidar echo signal component with high quality. Especially, the proposed method achieves 4 dB more improvement of signal-to-noise ratio (SNR) than a traditional homomorphic wavelet method.

Energization of Long HVAC Cables in Parallel - Analysis and Estimation Formulas

DEFF Research Database (Denmark)

Silva, Filipe Faria Da; Bak, Claus Leth

2012-01-01

The installation of long HVAC cables has recently become more common and it tends to increase during the next years. Consequently, the energization of long HVAC cables in parallel is also a more common condition. The energization of HVAC cables in parallel resembles the en-ergization of capacitor...... has several simplifications and does not always provide accurate results. This paper proposes a new formula that can be used for the estimation of these two quantities for two HVAC cables in parallel....

Advanced pulse oximeter signal processing technology compared to simple averaging. II. Effect on frequency of alarms in the postanesthesia care unit.

Science.gov (United States)

Rheineck-Leyssius, A T; Kalkman, C J

1999-05-01

To determine the effect of a new pulse oximeter (Nellcor Symphony N-3000, Pleasanton, CA) with signal processing technique (Oxismart) on the incidence of false alarms in the postanesthesia care unit (PACU). Prospective study. Nonuniversity hospital. 603 consecutive ASA physical status I, II, and III patients recovering from general or regional anesthesia in the PACU. We compared the number of alarms produced by a recently developed "third"-generation pulse oximeter (Nellcor Symphony N-3000) with Oxismart signal processing technique and a conventional pulse oximeter (Criticare 504, Waukesha, WI). Patients were randomly assigned to either a Nellcor pulse oximeter or a Criticare with the signal averaging time set at either 12 or 21 seconds. For each patient the number of false (artifact) alarms was counted. The Nellcor generated one false alarm in 199 patients and 36 (in 31 patients) "loss of pulse" alarms. The conventional pulse oximeter with the averaging time set at 12 seconds generated a total of 32 false alarms in 17 of 197 patients [compared with the Nellcor, relative risk (RR) 0.06, confidence interval (CI) 0.01 to 0.25] and a total of 172 "loss of pulse" alarms in 79 patients (RR 0.39, CI 0.28 to 0.55). The conventional pulse oximeter with the averaging time set at 21 seconds generated 12 false alarms in 11 of 207 patients (compared with the Nellcor, RR 0.09, CI 0.02 to 0.48) and a total of 204 "loss of pulse" alarms in 81 patients (RR 0.40, CI 0.28 to 0.56). The lower incidence of false alarms of the conventional pulse oximeter with the longest averaging time compared with the shorter averaging time did not reach statistical significance (false alarms RR 0.62, CI 0.3 to 1.27; "loss of pulse" alarms RR 0.98, CI 0.77 to 1.3). To date, this is the first report of a pulse oximeter that produced almost no false alarms in the PACU.

Estudio de viabilidad de un sistema de generación de energía eléctrica basado en energías renovables para países en vías de desarrollo

OpenAIRE

Villanueva Fernández, Gemma

2010-01-01

En este proyecto, primero se realiza una pequeña introducción para que el lector adquiera unos conocimientos mínimos sobre las energías renovables. Posteriormente, se describe los conceptos básicos de la energía solar fotovoltaica y los materiales usados en la misma. La energía solar fotovoltaica, es una transformación de la energía luminosa en energía eléctrica. El material más utilizado en la fabricación de los paneles solares es el silicio. De igual forma, se describe conceptos básicos de ...

Obtención de energía a partir de las corrientes marinas

OpenAIRE

Echeverría Cabodevilla, Álvaro

2017-01-01

El objetivo del proyecto es evaluar la viabilidad de una granja de energía hidrocinética en los territorios marinos españoles. Como se puede observar en el desarrollo del estudio, el resultado es negativo. En España no existe una gran zona que pueda ser utilizada para crear una granja de energía hidrocinética. La energía hidrocinética es aquella que utiliza la energía cinética del agua marina para obtener electricidad, principalmente los movimientos de agua de las corrientes ma...

Energizing Subject Guide Service with Web 2.0

Directory of Open Access Journals (Sweden)

Sheau-Hwang Chang

2014-06-01

Full Text Available This article will use LibGuides as an example to illustrate how a Web 2.0 platform can energize the subject guide service and give librarians an edge in expanding their roles. Topics to be discussed will include a brief introduction to LibGuides and its capabilities to energize subject guide creation, how it has been used by academic libraries, how it is used in Maxwell Library in expanding librarian's role, and finally its implications on librarianship.

The New High Magnetic Field Laboratory at Dresden: a Pulsed-Field Laboratory at an IR Free-Electron-Laser

International Nuclear Information System (INIS)

Pobell, F.; Bianchi, A. D.; Herrmannsdoerfer, T.; Krug, H.; Zherlitsyn, S.; Zvyagin, S.; Wosnitza, J.

2006-01-01

We report on the construction of a new high magnetic field user laboratory which will offer pulsed-field coils in the range (60 T, 500 ms, 40 mm) to (100 T, 10 ms, 20 mm) for maximum field, pulse time, and bore diameter of the coils. These coils will be energized by a modular 50 MJ/24 kV capacitor bank. Besides many other experimental techniques, as unique possibilities NMR in pulsed fields as well as infrared spectroscopy at 5 to 150 μm will be available by connecting the pulsed field laboratory to a nearby free-electron-laser facility

Pulse Generator

Science.gov (United States)

Greer, Lawrence (Inventor)

2017-01-01

An apparatus and a computer-implemented method for generating pulses synchronized to a rising edge of a tachometer signal from rotating machinery are disclosed. For example, in one embodiment, a pulse state machine may be configured to generate a plurality of pulses, and a period state machine may be configured to determine a period for each of the plurality of pulses.

Evaluation of bistable systems versus matched filters in detecting bipolar pulse signals

OpenAIRE

Duan, Fabing; Abbott, Derek; Gao, Qisheng

2004-01-01

This paper presents a thorough evaluation of a bistable system versus a matched filter in detecting bipolar pulse signals. The detectability of the bistable system can be optimized by adding noise, i.e. the stochastic resonance (SR) phenomenon. This SR effect is also demonstrated by approximate statistical detection theory of the bistable system and corresponding numerical simulations. Furthermore, the performance comparison results between the bistable system and the matched filter show that...

Evaluation of pulse oximeter derived photoplethysmographic signals for obstructive sleep apnea diagnosis

OpenAIRE

Li, Yan; Gao, He; Ma, Yan

2017-01-01

Abstract High prevalence of obstructive sleep apnea (OSA) has increased the demands for more convenient and accessible diagnostic devices other than standard in-lab polysomnography (PSG). Despite the increasing utility of photoplethysmograph (PPG), it remains understudied in underserved populations. This study aimed to evaluate the reliability of a standard pulse oximeter system with an automated analysis based on the PPG signal for the diagnosis of OSA, as compared with PSG derived measures....

Estudio del balance energético en velocistas de alto rendimiento

OpenAIRE

Lorente Gutiérrez, Jesús

2015-01-01

El objetivo de este estudio fue evaluar el balance energético en tres atletas de alto rendimiento durante 28 días, que coincidieron con el periodo competitivo de pista cubierta. La ingesta energética fue estudiada a partir de registros alimentarios durante los 28 días. Del mismo modo, el gasto energético fue estimado por tres métodos, mediante registros de actividad durante 28 días, mediante el estudio del ritmo metabólico basal estudiado por calorimetría indirecta, aplicándole el fa...

Modelado Energético de Convertidores Primarios para el Aprovechamiento de las Energías Renovables Marinas

Directory of Open Access Journals (Sweden)

Amable López

2014-04-01

Full Text Available Resumen: El objetivo principal de este artículo es presentar los métodos más habituales de aprovechamiento de distintos tipos de energías renovables procedentes del mar y analizar los modelos energéticos de los dispositivos utilizados para su explotación. Estos modelos son necesarios para el diseño del dispositivo así como para el estudio de su comportamiento dinámico. Su conocimiento resulta imprescindible también para su simulación dinámica y para el diseño de los algoritmos de control necesarios para conseguir una optimización energética y económica. En este trabajo se presentan algunos de los diferentes tipos de energías del mar, y se j ustifica el interés en el desarrollo de dispositivos específicos para el aprovechamiento de las corrientes marinas y de las olas, junto con una pequeña clasificación en función de la profundidad del agua en la zona de instalación de estos dispositivos. Para los convertidores de energía de las olas, generalmente, de tipo resonante, se presenta una metodología de tipo general, analizando los distintos campos de fuerzas actuantes y los métodos de obtención de las respuestas temporal y frecuencial. Para los dispositivos de aprovechamiento de las corrientes, se propone una metodología simplificada de modelado dinámico que puede ser utilizada en análisis del dispositivo concreto. Para ello se tiene en cuenta los perfiles hidrodinámicos que utilizan estos dispositivos, los datos del perfil de la corriente con la profundidad y del modelo de oleaje, y la dinámica propia del conjunto multiplicadora y generador eléctrico. La metodología propuesta se aplica al estudio de un caso concreto, correspondiente a un rotor de eje horizontal de un convertidor de energía de las corrientes. Los resultados obtenidos permiten analizar los efectos del oleaje y de las condiciones de flujo de la corriente no uniforme sobre las magnitudes energéticas más importantes. Abstract: The main objective of

Dynamic pulse difference circuit

International Nuclear Information System (INIS)

Erickson, G.L.

1978-01-01

A digital electronic circuit of especial use for subtracting background activity pulses in gamma spectrometry is disclosed which comprises an up-down counter connected to count up with signal-channel pulses and to count down with background-channel pulses. A detector responsive to the count position of the up-down counter provides a signal when the up-down counter has completed one scaling sequence cycle of counts in the up direction. In an alternate embodiment, a detector responsive to the count position of the up-down counter provides a signal upon overflow of the counter

Multimode pulse counter

International Nuclear Information System (INIS)

Natanzon, D.D.

1982-01-01

A pulse counter with code conversion is described. The counter is based on the integrated circuits of direct-counting devices of medium integration. The counter ensures various modes of pulse counting depending on the logical control signals: reversible, two-channel summing, one-channel summing binary, summing with ''storage'' signal code fixation without interrupting pulse counting. Arrangement of the suggested structure as a microcircuit of medium integration might contribute to reduction in the counter type nomenclature in digital families of widely used integrated circuits

A study of new pulse auscultation system.

Science.gov (United States)

Chen, Ying-Yun; Chang, Rong-Seng

2015-04-14

This study presents a new type of pulse auscultation system, which uses a condenser microphone to measure pulse sound waves on the wrist, captures the microphone signal for filtering, amplifies the useful signal and outputs it to an oscilloscope in analog form for waveform display and storage and delivers it to a computer to perform a Fast Fourier Transform (FFT) and convert the pulse sound waveform into a heartbeat frequency. Furthermore, it also uses an audio signal amplifier to deliver the pulse sound by speaker. The study observed the principles of Traditional Chinese Medicine's pulsing techniques, where pulse signals at places called "cun", "guan" and "chi" of the left hand were measured during lifting (100 g), searching (125 g) and pressing (150 g) actions. Because the system collects the vibration sound caused by the pulse, the sensor itself is not affected by the applied pressure, unlike current pulse piezoelectric sensing instruments, therefore, under any kind of pulsing pressure, it displays pulse changes and waveforms with the same accuracy. We provide an acquired pulse and waveform signal suitable for Chinese Medicine practitioners' objective pulse diagnosis, thus providing a scientific basis for this Traditional Chinese Medicine practice. This study also presents a novel circuit design using an active filtering method. An operational amplifier with its differential features eliminates the interference from external signals, including the instant high-frequency noise. In addition, the system has the advantages of simple circuitry, cheap cost and high precision.

Balance de energía en cultivos hortícolas a campo en Rosario (Santa Fe, Argentina

Directory of Open Access Journals (Sweden)

J. Denoia

2010-01-01

Full Text Available Se analizó la gestión de la energía en cultivos de papa, tomate y lechuga en un área próxima a la ciudad de Rosario (Argentina. Se consideraron todos los ingresos de materia al sistema y su producción transformándolos en energía al multiplicar las cantidades de insumos por sus contenidos energéticos. Se analizó tanto la energía directa como la indirecta. Se estudió la gestión energética dentro de los límites físicos del sistema. Los indicadores empleados fueron: eficiencia energética (EfE y productividad energética (PE. Los balances energéticos de papa y tomate fueron negativos, mientras que en lechuga, la energía producida fue menor que la ingresada. La mayor eficiencia energética se registró en tomate (3,54, seguida por papa (2,69; la menor fue en lechuga (0,25. La energía ingresada en tomate resultó la más eficiente (88,6 kgMS/100 Mj, seguida por la de papa (16 kgMS/100 Mj y la de lechuga (10,8 kgMS/100 Mj.

La inversión en energías renovables en Argentina

OpenAIRE

Recalde, Marina

2017-01-01

En este artículo se analiza en qué medida los factores del entorno de la política energética de un país en desarrollo, tal como Argentina, determinan la evolución de la inversión en energías renovables. La baja calidad institucional del país ayuda a crear condiciones no propicias que contrarrestan el efecto de la política energética, reduciendo los incentivos para invertir en tecnologías renovables. Es necesario entonces mejorar las condiciones institucionales de los países en desarrollo para...

Design and measurements of a fast high-voltage pulse generator for the MedAustron Low Energy Transfer line fast deflector

CERN Document Server

Fowler, T; Mueller, F; Kramer, T; Stadlbauer, T

2012-01-01

MedAustron, a centre for ion-therapy and research, will comprise an accelerator facility based on a synchrotron for the delivery of protons and light ions for cancer treatment. The Low Energy Beam Transfer line (LEBT) to the synchrotron contains an electrostatic fast deflector (EFE) which, when energized, deviates the continuous beam arriving from the ion source onto a Faraday Cup: the specified voltage is ±3.5 kV. De-energizing the EFE for variable pulse durations from 500 ns up to d.c. allows beam passage for multi-turn injection into the synchrotron. To maintain beam quality in the synchrotron, the EFE pulse generator requires rise and fall times of less than 300 ns between 90 % of peak voltage and a ±1 V level. To achieve this, a pulsed power supply (PKF), with high voltage MOSFET switches connected in a push-pull configuration, will be mounted in close proximity to the deflector itself. A fast, large dynamic range monitoring circuit will verify switching to the ±1 V level and subsequent flat bottom pu...

Evaluation of Masimo signal extraction technology pulse oximetry in anaesthetized pregnant sheep.

Science.gov (United States)

Quinn, Christopher T; Raisis, Anthea L; Musk, Gabrielle C

2013-03-01

Evaluation of the accuracy of Masimo signal extraction technology (SET) pulse oximetry in anaesthetized late gestational pregnant sheep. Prospective experimental study. Seventeen pregnant Merino ewes. Animals included in study were late gestation ewes undergoing general anaesthesia for Caesarean delivery or foetal surgery in a medical research laboratory. Masimo Radical-7 pulse oximetry (SpO(2) ) measurements were compared to co-oximetry (SaO(2) ) measurements from arterial blood gas analyses. The failure rate of the pulse oximeter was calculated. Accuracy was assessed by Bland & Altman's (2007) limits of agreement method. The effect of mean arterial blood pressure (MAP), perfusion index (PI) and haemoglobin (Hb) concentration on accuracy were assessed by regression analysis. Forty arterial blood samples paired with SpO(2) and blood pressure measurements were obtained. SpO(2) ranged from 42 to 99% and SaO(2) from 43.7 to 99.9%. MAP ranged from 24 to 82 mmHg, PI from 0.1 to 1.56 and Hb concentration from 71 to 114 g L(-1) . Masimo pulse oximetry measurements tended to underestimate oxyhaemoglobin saturation compared to co-oximetry with a bias (mean difference) of -2% and precision (standard deviation of the differences) of 6%. Accuracy appeared to decrease when SpO(2) was oximeter function during extreme hypotension and hypoxaemia. © 2012 The Authors. Veterinary Anaesthesia and Analgesia. © 2012 Association of Veterinary Anaesthetists and the American College of Veterinary Anesthesiologists.

An in vivo investigation of photoplethysmographic signals and preliminary pulse oximetry estimation from the bowel using a new fiberoptic sensor.

Science.gov (United States)

Hickey, Michelle; Samuels, Neal; Randive, Nilesh; Langford, Richard M; Kyriacou, Panayiotis A

2011-05-01

The continuous monitoring of splanchnic organ oxygen saturation could make the early detection of inadequate tissue oxygenation feasible, reducing the risk of hypoperfusion, severe ischemia, multiple organ failure, and, ultimately, death. Current methods for assessing splanchnic perfusion have not been widely accepted for use in the clinical care environment. In an attempt to overcome the limitations of the current techniques, a new fiberoptic photoplethysmographic (PPG)/pulse oximetry sensor was developed as a means of assessing splanchnic organ perfusion during surgery in humans. A new fiberoptic splanchnic pulse oximeter and an optically identical fiberoptic finger pulse oximeter have been developed. Simultaneous PPG signals and preliminary estimates of arterial oxygen saturation from the bowel (small and large) and finger were obtained in 17 patients (3 men and 14 women) undergoing open laparotomy. Good quality PPG signals were obtained from the small and large bowel and from the finger in all patients (lower 95% confidence limit for the proportion was 0.64). Comparisons of blood oxygen saturation values acquired when using the splanchnic and the finger fiberoptic sensors and a commercial finger pulse oximeter indicated that there was no statistically significant difference between them (all P>0.454). A Bland and Altman plot of the difference between blood oxygen saturation values from the bowel fiberoptic pulse oximeter and the fiberoptic finger pulse oximeter against their mean showed that the limits of agreement between the 2 pulse oximeters were -3.8% and 4.2% for small bowel measurements, and -3.4% and 4.3% for large bowel measurements. The 95% prediction interval for the difference between the 2 devices was between -4.2% and 4.7%. This study demonstrated that good quality PPG signals can be obtained from the bowel using a new fiberoptic sensor. Further evaluation is required to determine whether fiberoptic pulse oximetry of the bowel may provide a

Auditoría energética en una planta de tratamiento de agua potable

OpenAIRE

Díaz Álvarez, Silvino

2012-01-01

En el panorama energético actual, con las recientes incertidumbres asociadas a los precios de la energía y las inestabilidades políticas en algunos países exportadores de hidrocarburos, reducir el consumo energético mediante tecnologías más eficientes es fundamental en la definición de nuevos usos de la energía en nuestra sociedad. Dada la actual coyuntura medioambiental, económica y social, hemos de encontrar un nuevo modelo de desarrollo sostenible, incrementando la productividad de nuestra...

CAMAC differential pulse discriminator-counter

International Nuclear Information System (INIS)

Tselikov, N.V.

1987-01-01

Differential pulse discriminator-counter for Moessbauer spectrometer is described. Input pulse setting into the channel is performed according to the following algorithm: the pulse is transmitted to the channel depending on the fact whether the preceding pulse has got to the discrimination window or not. The circuit does not contain delay lines, taking into account the delay of a signal from the upper level discriminator in relation to the lower level discriminator signal, which is connected with input pulse rise finite time, which in turn allows one to reduce the discriminator dead time up to the operation time of threshold circuits. The pulse counting rate is 150 MHz, input signal amplitude is ±3 V, dead time is 6 ns, delay time from input to output is 14 ns. The unit is made in CAMAC system

Assessing potential impacts of energized submarine power cables on crab harvests

Science.gov (United States)

Love, Milton S.; Nishimoto, Mary M.; Clark, Scott; McCrea, Merit; Bull, Ann Scarborough

2017-12-01

Offshore renewable energy facilities transmit electricity to shore through submarine power cables. Electromagnetic field emissions (EMFs) are generated from the transmission of electricity through these cables, such as the AC inter-array (between unit) and AC export (to shore) cables often used in offshore energy production. The EMF has both an electric component and a magnetic component. While sheathing can block the direct electric field, the magnetic field is not blocked. A concern raised by fishermen on the Pacific Coast of North America is that commercially important Dungeness crab (Metacarcinus magister Dana, 1852)) might not cross over an energized submarine power cable to enter a baited crab trap, thus potentially reducing their catch. The presence of operating energized cables off southern California and in Puget Sound (cables that are comparable to those within the arrays of existing offshore wind energy devices) allowed us to conduct experiments on how energized power cables might affect the harvesting of both M. magister and another commercially important crab species, Cancer productus Randall, 1839. In this study we tested the questions: 1) Is the catchability of crabs reduced if these animals must traverse an energized power cable to enter a trap and 2) if crabs preferentially do not cross an energized cable, is it the cable structure or the EMF emitted from that cable that deters crabs from crossing? In field experiments off southern California and in Puget Sound, crabs were given a choice of walking over an energized power cable to a baited trap or walking directly away from that cable to a second baited trap. Based on our research we found no evidence that the EMF emitted by energized submarine power cables influenced the catchability of these two species of commercially important crabs. In addition, there was no difference in the crabs' responses to lightly buried versus unburied cables. We did observe that, regardless of the position of the cable

Spatially Localized Particle Energization by Landau Damping in Current Sheets

Science.gov (United States)

Howes, G. G.; Klein, K. G.; McCubbin, A. J.

2017-12-01

Understanding the mechanisms of particle energization through the removal of energy from turbulent fluctuations in heliospheric plasmas is a grand challenge problem in heliophysics. Under the weakly collisional conditions typical of heliospheric plasma, kinetic mechanisms must be responsible for this energization, but the nature of those mechanisms remains elusive. In recent years, the spatial localization of plasma heating near current sheets in the solar wind and numerical simulations has gained much attention. Here we show, using the innovative and new field-particle correlation technique, that the spatially localized particle energization occurring in a nonlinear gyrokinetic simulation has the velocity space signature of Landau damping, suggesting that this well-known collisionless damping mechanism indeed actively leads to spatially localized heating in the vicinity of current sheets.

Role conflict: cause of burnout or energizer?

Science.gov (United States)

Jones, M L

1993-03-01

A year-long study of public child welfare administrators examined the effects of role conflict on their attitudes and performance. Popular belief and some of the literature have suggested that burnout is inevitable for those confronted with role conflict. Other literature has proposed that it may instead be energizing to individuals and lead to greater personal and organizational effectiveness. This qualitative study found that individuals in the study had developed specific, effective skills for responding to role conflict. Although there was a public presentation of self that indicated they were under stress and in "impossible" situations, there was in fact an energizing effect resulting from the ongoing challenge of dealing with conflict.

Nexo agua-energía: desde el nacimiento del río Llobregat hasta Manresa

OpenAIRE

Prieto Márquez, Kelly; Badia Padilla, Ester; Grau Vilalta, Maria Dolors

2017-01-01

En este trabajo se estudia el nexo agua-energía en el tramo del río Llobregat desde Castellar de N’hug hasta Manresa. Se lleva a cabo una evaluación de la cantidad de energía necesaria en las estaciones potabilizadoras y depuradoras para adecuar el agua del río, además de determinar la cantidad de energía que generan las centrales mini-hidroeléctricas. Estos dos valores de energía finales son comparados para demostrar si se consume más energía que la que se genera, o al contrario. Se estud...

A Study of New Pulse Auscultation System

Directory of Open Access Journals (Sweden)

Ying-Yun Chen

2015-04-01

Full Text Available This study presents a new type of pulse auscultation system, which uses a condenser microphone to measure pulse sound waves on the wrist, captures the microphone signal for filtering, amplifies the useful signal and outputs it to an oscilloscope in analog form for waveform display and storage and delivers it to a computer to perform a Fast Fourier Transform (FFT and convert the pulse sound waveform into a heartbeat frequency. Furthermore, it also uses an audio signal amplifier to deliver the pulse sound by speaker. The study observed the principles of Traditional Chinese Medicine’s pulsing techniques, where pulse signals at places called “cun”, “guan” and “chi” of the left hand were measured during lifting (100 g, searching (125 g and pressing (150 g actions. Because the system collects the vibration sound caused by the pulse, the sensor itself is not affected by the applied pressure, unlike current pulse piezoelectric sensing instruments, therefore, under any kind of pulsing pressure, it displays pulse changes and waveforms with the same accuracy. We provide an acquired pulse and waveform signal suitable for Chinese Medicine practitioners’ objective pulse diagnosis, thus providing a scientific basis for this Traditional Chinese Medicine practice. This study also presents a novel circuit design using an active filtering method. An operational amplifier with its differential features eliminates the interference from external signals, including the instant high-frequency noise. In addition, the system has the advantages of simple circuitry, cheap cost and high precision.

Pulsed power supply system for the fast quadrupoles in the AGS

International Nuclear Information System (INIS)

Nawrocky, R.J.; Lambiase, R.F.

1983-01-01

In the acceleration of polarized protons in the AGS, a number of depolarizing resonances will be encountered. Depolarization due to the so-called intrinsic resonances will be minimized by crossing each resonance in less than one beam revolution period (approx. 2 μs). This will be accomplished with a set of twelve fast tune-shifting quadrupoles distributed symmetrically around the ring. During a typical acceleration cycle, the fast quads will be energized with a burst of alternating polarity, fast rise/slow fall triangular current pulses. The amplitude of these pulses will vary from 160 A to about 2700 A peak. This paper describes the development of the pulsed power supply for the fast quads, the construction of a prototype modulator, and some of the initial test results obtained with the prototype

Eficiencia energética de los edificios: repercusión medioambiental

Directory of Open Access Journals (Sweden)

Maria Nieves Pacheco Jiménez

2009-06-01

Full Text Available Los recientes Planes, Estrategias y normas atinentes al fomento de la eficiencia energética en los edificios1 nacen en un contexto de preocupación por el cambio climático y sus consecuencias. Todos ellos persiguen la reducción de costes energéticos y la promoción de la sostenibilidad económica, política y ambiental. Un reflejo de esta inquietud por el bajo impacto ambiental puede observarse en el sector de la vivienda, cuyo consumo final de energía es muy elevado, y en la consiguiente intención de construir edificios bioclimáticos que aprovechen la energía del entorno. En aras a la consecución de estos objetivos, el Plan de Acción 2008-2012 impulsa una serie de medidas que recaen sobre el sector transporte, la industria, el sector residencial y el sector terciario, articulándose en torno a cuatro líneas de actuación: transversal, de movilidad, de edificios y de ahorro eléctrico. Este estudio aborda las pautas de ahorro y eficiencia energética propuestas para los edificios, tanto existentes como de nueva construcción, así como residenciales y del sector terciario. Para ello se hace imprescindible la remisión al concepto de “calidad” de los edificios, contemplado en la propia Exposición de Motivos de la Ley 38/1999, de Ordenación de la Edificación, y ligado estrechamente a la eficiencia energética de aquéllos.

Random pulse generator

International Nuclear Information System (INIS)

Guo Ya'nan; Jin Dapeng; Zhao Dixin; Liu Zhen'an; Qiao Qiao; Chinese Academy of Sciences, Beijing

2007-01-01

Due to the randomness of radioactive decay and nuclear reaction, the signals from detectors are random in time. But normal pulse generator generates periodical pulses. To measure the performances of nuclear electronic devices under random inputs, a random generator is necessary. Types of random pulse generator are reviewed, 2 digital random pulse generators are introduced. (authors)

Situación energética de los hidrocarburos en el Perú

OpenAIRE

Rojas Lazo, Oswaldo; Rojas Rojas, Jorge; Salas Bacalla, Julio

2014-01-01

La tasa de crecimiento anual del consumo de energía en el mundo se incrementa a razón de 2 a 3%, teniendo a los hidrocarburos y el carbón como sus principales componentes. En el Perú las reservas probadas de energía son: gas (Camisea) con el 43% de la energía comercial, la hidroenergía 23,1%, los líquidos de gas natural con el 14,7% y otros con el 19.2%. La balanza comercial energética en el Perú es negativa, la producción de petróleo en los últimos años está descendiendo mientras que la prod...

Los balances energéticos en la producción agropecuaria.

OpenAIRE

Yepes Jaramillo, Guillermo; Martínez Bustamante, Enrique

2011-01-01

A través de este ensayo se presenta otro enfoque de análisis de la energía utilizada por los vegetales para la producción agraria. Se parte de los conceptos fundamentales relacionados con la termodinámica y la manera como el flujo de energía incide sobre el follaje de la vegetación y se distribuye, a través de las hojas, en todo el dosel de comunidades de plantas. La vida en la tierra es mantenida por el flujo de energía radiado por el sol y que entra en la biosfera. Por medio de la fotosínte...

Energía y cambio climático

OpenAIRE

Wilfredo Bulege Gutiérrez

2014-01-01

Es claro que el crecimiento de la población, la extracción de materiales, la producción alimentaria y el incremento de energía para todas las actividades humanas nos conducen a un estado de colisión con las capacidades de la biosfera y los ecosistemas en el proceso de asegurar la provisión de bienes y servicios indispensables para la vida (1). La producción de energía convencional y contaminante es hoy una de las más graves en este escenario, tanto que la comunidad internacional y las potenci...

Software emulator of nuclear pulse generation with different pulse shapes and pile-up

Energy Technology Data Exchange (ETDEWEB)

Pechousek, Jiri, E-mail: jiri.pechousek@upol.cz [Department of Experimental Physics, Faculty of Science, Palacky University, 17. listopadu 1192/12, 771 46 Olomouc (Czech Republic); Konecny, Daniel [Department of Optics, Faculty of Science, Palacky University, 17. listopadu 1192/12, 77 146 Olomouc (Czech Republic); Novak, Petr; Kouril, Lukas; Kohout, Pavel [Department of Experimental Physics, Faculty of Science, Palacky University, 17. listopadu 1192/12, 771 46 Olomouc (Czech Republic); Celiktas, Cuneyt [Department of Physics, Faculty of Science, Ege University, Bornova, Izmir (Turkey); Vujtek, Milan [Department of Experimental Physics, Faculty of Science, Palacky University, 17. listopadu 1192/12, 771 46 Olomouc (Czech Republic)

2016-08-21

The optimal detection of output signals from nuclear counting devices represents one of the key physical factors that govern accuracy and experimental reproducibility. In this context, the fine calibration of the detector under diverse experimental scenarios, although time costly, is necessary. However this process can be rendered easier with the use of systems that work in lieu of emulators. In this report we describe an innovative programmable pulse generator device capable to emulate the scintillation detector signals, in a way to mimic the detector performances under a variety of experimental conditions. The emulator generates a defined number of pulses, with a given shape and amplitude in the form of a sampled detector signal. The emulator output is then used off-line by a spectrometric system in order to set up its optimal performance. Three types of pulse shapes are produced by our device, with the possibility to add noise and pulse pile-up effects into the signal. The efficiency of the pulse detection, pile-up rejection and/or correction, together with the dead-time of the system, are therein analyzed through the use of some specific algorithms for pulse processing, and the results obtained validate the beneficial use of emulators for the accurate calibration process of spectrometric systems.

Optical spectral reshaping for directly modulated 4-pulse amplitude modulation signals

DEFF Research Database (Denmark)

Ozolins, Oskars; Da Ros, Francesco; Cristofori, Valentina

2017-01-01

The tremendous traffic growth in intra/inter-datacenters requires low-cost high-speed integrated solutions [1]. To enable a significantly reduced footprint directly modulated lasers (DMLs) have been proposed instead of large external modulators. However, it is challenging to use DMLs due to their......The tremendous traffic growth in intra/inter-datacenters requires low-cost high-speed integrated solutions [1]. To enable a significantly reduced footprint directly modulated lasers (DMLs) have been proposed instead of large external modulators. However, it is challenging to use DMLs due...... (PAM) [3] signals. However, moving to 4-PAM,many of the impressive demonstrations reported so far rely heavily on off-line digital signal processing (DSP), which increases latency, power consumption and cost. In this talk, we report on (i) a detailed numerical analysis on the complex transfer function...... of the optical filter for optical spectral reshaping in case of pulse amplitude modulation and(ii) an experimental demonstration of real-time dispersion-uncompensated transmission of 10-GBd and 14-GBd 4-PAM signals up to 10- and 26-km SSMF. This is achieved by combining a commercial 10-Gb/s DML with optical...

Bayesian signal processing of pulse shapes for background rejection in the Majorana Demonstrator

Science.gov (United States)

Shanks, Benjamin; Majorana Collaboration

2015-10-01

The Majorana Demonstrator uses high purity germanium (HPGe) detectors in the p-type point contact (PPC) geometry to search for neutrinoless double-beta decay (0 νββ) in 76Ge. Due to the unique electric potential created within the PPC geometry, the detailed pulse shape depends on the number of energy depositions contained within a given event. Pulse shape analysis (PSA) techniques can be used to estimate the number of separate depositions which combine to form a single pulse. This information can be used to discriminate between 0 νββ candidate events, which deposit energy at a single detector site, and gamma ray background, which can scatter and deposit energy in multiple locations. The problem of determining whether a pulse is single- or multi-site is well suited to Bayesian classifiers. Once trained via supervised machine learning, these algorithms can perform nonlinear cuts against multi-site events using the estimated probability function as a discriminator. The Bayesian approach can also be naturally extended to incorporate a model of the physical process responsible for signal generation within the detector. Presented here is an overview of the Bayesian classifier developed for use on the Demonstrator. This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Nuclear Physics, the Particle Astrophysics Program of the National Science Foundation, and the Sanford Underground Research Facility.

Extracción de energía del agua mediante generadores piezoeléctricos

OpenAIRE

Rodríguez Mendoza, Iker

2014-01-01

El desarrollo del Proyecto consiste, por una parte, en el estudio sobre la respuesta de los materiales piezoeléctricos como generadores de energía en un entorno acuoso que está sometido a variaciones de potencial y, por otra, en el estudio técnico y económico de un equipo basado en la utilización esta fuente de energía y su comercialización en el mercado energético. Esta energía es la que se obtiene de la fuerza de arrastre del agua al desplazarse a causa del movimiento ondulatorio de las ol...

Cuantificación del potencial energético undimotriz en las costas del Caribe colombiano

Directory of Open Access Journals (Sweden)

Jaime P

2017-11-01

Full Text Available En este documento se describen los avances en la cuantificación de la energía de las olas de la costa caribeña colombiana. La metodología utilizada servirá como punto de partida para establecer el potencial energético en Colombia para este tipo de suministro energético. En la actualidad, el potencial energético teórico estimado en las ondas de la costa cercana en la costa atlántica es de aproximadamente 1107 MW y esto fue posible con datos que se han recogido y procesado desde enero de 2014. Las ecuaciones que tienen en cuenta variables tales como: la densidad del agua de mar, la temperatura y la velocidad del viento en la zona. También muestra el progreso del diseño del sistema Near Shore para la verificación del potencial de energía de las olas que consiste en un dispositivo que transforma la energía cinética de las ondas del mar en energía potencial gravitacional que se va a usar para mover un generador de corriente alterna.

Kinetic Simulations of Plasma Energization and Particle Acceleration in Interacting Magnetic Flux Ropes

Science.gov (United States)

Du, S.; Guo, F.; Zank, G. P.; Li, X.; Stanier, A.

2017-12-01

The interaction between magnetic flux ropes has been suggested as a process that leads to efficient plasma energization and particle acceleration (e.g., Drake et al. 2013; Zank et al. 2014). However, the underlying plasma dynamics and acceleration mechanisms are subject to examination of numerical simulations. As a first step of this effort, we carry out 2D fully kinetic simulations using the VPIC code to study the plasma energization and particle acceleration during coalescence of two magnetic flux ropes. Our analysis shows that the reconnection electric field and compression effect are important in plasma energization. The results may help understand the energization process associated with magnetic flux ropes frequently observed in the solar wind near the heliospheric current sheet.

Response Analysis on Electrical Pulses under Severe Nuclear Accident Temperature Conditions Using an Abnormal Signal Simulation Analysis Module

Directory of Open Access Journals (Sweden)

Kil-Mo Koo

2012-01-01

Full Text Available Unlike design basis accidents, some inherent uncertainties of the reliability of instrumentations are expected while subjected to harsh environments (e.g., high temperature and pressure, high humidity, and high radioactivity occurring in severe nuclear accident conditions. Even under such conditions, an electrical signal should be within its expected range so that some mitigating actions can be taken based on the signal in the control room. For example, an industrial process control standard requires that the normal signal level for pressure, flow, and resistance temperature detector sensors be in the range of 4~20 mA for most instruments. Whereas, in the case that an abnormal signal is expected from an instrument, such a signal should be refined through a signal validation process so that the refined signal could be available in the control room. For some abnormal signals expected under severe accident conditions, to date, diagnostics and response analysis have been evaluated with an equivalent circuit model of real instruments, which is regarded as the best method. The main objective of this paper is to introduce a program designed to implement a diagnostic and response analysis for equivalent circuit modeling. The program links signal analysis tool code to abnormal signal simulation engine code not only as a one body order system, but also as a part of functions of a PC-based ASSA (abnormal signal simulation analysis module developed to obtain a varying range of the R-C circuit elements in high temperature conditions. As a result, a special function for abnormal pulse signal patterns can be obtained through the program, which in turn makes it possible to analyze the abnormal output pulse signals through a response characteristic of a 4~20 mA circuit model and a range of the elements changing with temperature under an accident condition.

Performance Analysis of the Effect of Pulsed-Noise Interference on WLAN Signals Transmitted Over a Nakagami Fading Channel

National Research Council Canada - National Science Library

Tsoumanis, Andreas

2004-01-01

...) coding with soft decision decoding (SDD) and maximum- likelihood detection improves performance as compared to uncoded signals, In addition, the combination of maximum-likelihood detection and error connection coding renders pulsed-noise...

La energía nuclear y la industria en Francia

Directory of Open Access Journals (Sweden)

Roux, A.

1980-09-01

Full Text Available In this article an analysis is made of the favorable effects for industry involved in the development of nuclear energy and the interaction between them. Reference is made to the problem of energy supply in France and the need for an effort in energy savings, to the development of new sources and priority in the establishment of an important program of nuclear power plants. Also, an analysis is made of the role of Industry, the Atomic Energy and Electricity Commission of France in the supply and processing of the nuclear materials. Finally, a general review of the manpower and technical means presently available is made, as well as an examination of the investments foreseen for local development of this energy.

En este artículo se analizan los efectos favorables que para la Industria tiene el desarrollo de la energía nuclear y las interacciones entre ambas. Se hace referencia al problema del aprovisionamiento energético en Francia y a la necesidad de un esfuerzo en materia de ahorro de energía, al desarrollo de nuevas fuentes y a la prioridad en el establecimiento de un importante programa de centrales nucleares. También es analizado el papel de la Industria, la Comisaría de Energía Atómica y Electricidad de Francia en el abastecimiento y en la transformación de los materiales nucleares. Por último, se hace un repaso general de los medios humanos y técnicos con que se cuenta en la actualidad, así como de las inversiones previstas para un desarrollo nacional de esta energía.

Ultra-wideband short-pulse radar with range accuracy for short range detection

Energy Technology Data Exchange (ETDEWEB)

Rodenbeck, Christopher T; Pankonin, Jeffrey; Heintzleman, Richard E; Kinzie, Nicola Jean; Popovic, Zorana P

2014-10-07

An ultra-wideband (UWB) radar transmitter apparatus comprises a pulse generator configured to produce from a sinusoidal input signal a pulsed output signal having a series of baseband pulses with a first pulse repetition frequency (PRF). The pulse generator includes a plurality of components that each have a nonlinear electrical reactance. A signal converter is coupled to the pulse generator and configured to convert the pulsed output signal into a pulsed radar transmit signal having a series of radar transmit pulses with a second PRF that is less than the first PRF.

Global synchronization of parallel processors using clock pulse width modulation

Science.gov (United States)

Chen, Dong; Ellavsky, Matthew R.; Franke, Ross L.; Gara, Alan; Gooding, Thomas M.; Haring, Rudolf A.; Jeanson, Mark J.; Kopcsay, Gerard V.; Liebsch, Thomas A.; Littrell, Daniel; Ohmacht, Martin; Reed, Don D.; Schenck, Brandon E.; Swetz, Richard A.

2013-04-02

A circuit generates a global clock signal with a pulse width modification to synchronize processors in a parallel computing system. The circuit may include a hardware module and a clock splitter. The hardware module may generate a clock signal and performs a pulse width modification on the clock signal. The pulse width modification changes a pulse width within a clock period in the clock signal. The clock splitter may distribute the pulse width modified clock signal to a plurality of processors in the parallel computing system.

Costo energético de las labores de preparación de suelo en Cuba

OpenAIRE

Pedro Paneque Rondón; Dailyn Soto León

2007-01-01

El objetivo fundamental del trabajo fue determinar el costo energético de las operaciones agrícolas mecanizadas y comparar los costos energéticos de los distintos tamaños (anchos de trabajo) de los aperos más utilizados en el país para la preparación de suelo, testando la hipótesis de que el costo energético expresado en MJ/ha es independiente del tamaño del equipo. Los resultados de la investigación permitieron llegar a las siguientes conclusiones: los mayores costos energéticos cor...

Development of a field measurement instrument for nuclear electromagnetic pulse (NEMP) based on signal transmission through fiber

International Nuclear Information System (INIS)

Song Wenwu; Zhang Chuandong; Liu Yi; Chen Jiuchun; Fan Youwen

2007-01-01

This paper deals with design principles, development and performance of a field measurement instrument for nuclear electromagnetic pulse (EMP) based on signal transmission through fiber. To determine the minimum band width this instrument needs, we analyze cutoff spectrum of a time domain double exponential signal, employing Fast Fourier Transform (FFT), and get its inverse transform signal. Then we design the circuit of laser device and the circuit of measuring device according to previous analysis. This instrument meets requirements of related regulations. Its specifications meet requirements of NEMP hazard protection research and can be of great significance to it. (authors)

The Roles of Fluid Compression and Shear in Electron Energization during Magnetic Reconnection

Science.gov (United States)

Li, Xiaocan; Guo, Fan; Li, Hui; Birn, Joachim

2018-03-01

Particle acceleration in space and astrophysical reconnection sites is an important unsolved problem in studies of magnetic reconnection. Earlier kinetic simulations have identified several acceleration mechanisms that are associated with particle drift motions. Here, we show that, for sufficiently large systems, the energization processes due to particle drift motions can be described as fluid compression and shear, and that the shear energization is proportional to the pressure anisotropy of energetic particles. By analyzing results from fully kinetic simulations, we show that the compression energization dominates the acceleration of high-energy particles in reconnection with a weak guide field, and the compression and shear effects are comparable when the guide field is 50% of the reconnecting component. Spatial distributions of those energization effects reveal that reconnection exhausts, contracting islands, and island-merging regions are the three most important regions for compression and shear acceleration. This study connects particle energization by particle guiding-center drift motions with that due to background fluid motions, as in the energetic particle transport theory. It provides foundations for building particle transport models for large-scale reconnection acceleration such as those in solar flares.

An analyzer for pulse-interval times to study high-order effects in the processing of nuclear detector signals

International Nuclear Information System (INIS)

Denecke, B.; Jonge, S. de

1998-01-01

An electronic device to measure interval time density distributions of subsequent pulses in nuclear detectors and their electronics is described. The device has a pair-pulse resolution of 10 ns and 25 ns for 3 subsequent input signals. The conversion range is 4096 channels and the lowest channel width is 10 ns. Counter dead times, single and in series were studied and compared with the statistical model. True count rates were obtained from an exponential fit through the interval-time distribution

Análise dos impactos energéticos e econômicos do programa brasileiro de etiquetagem energética (PBE/Inmetro em coletores solares térmicos do Brasil

Directory of Open Access Journals (Sweden)

João Pedro Stefano Marchesini Fonseca

2018-01-01

Full Text Available O presente estudo avalia os impactos energéticos e econômicos do uso de coletores solares térmicos planos fechados, típicos do setor residencial, nas diferentes regiões geográficas do Brasil, considerando as classes de eficiência energética do Programa Brasileiro de Etiquetagem Energética – PBE/INMETRO. As avaliações energéticas mostraram que todas as classes de coletores solares, de A (mais eficiente a E (menos eficiente, apresentam significativos ganhos energéticos, em substituição aos chuveiros elétricos. Foi definida uma cidade representativa para cada região geográfica do país, bem como sua temperatura média ambiente e nível de radiação mensal, o volume diário de água do banho a ser aquecida pelo sistema e o chuveiro elétrico e também a área média de painel solar para cada residência. Posteriormente, foram coletadas as informações de custos dos modelos representativos em relação as classes de eficiência energética, bem como taxa de juros e tarifas de energia elétrica e, assim, foram calculadas as frações solares anuais. As análises econômicas, utilizando a ferramenta de Benefício Anual Líquido – BAL, mostraram que nem sempre é viável o consumidor residencial utilizar equipamentos mais eficientes, classe A (com o Selo PROCEL.

Development of Ultrasonic Pulse Compression Using Golay Codes

International Nuclear Information System (INIS)

Kim, Young H.; Kim, Young Gil; Jeong, Peter

1994-01-01

Conventional ultrasonic flaw detection system uses a large amplitude narrow pulse to excite a transducer. However, these systems are limited in pulse energy. An excessively large amplitude causes a dielectric breakage of the transducer, and an excessively long pulse causes decrease of the resolution. Using the pulse compression, a long pulse of pseudorandom signal can be used without sacrificing resolution by signal correlation. In the present work, the pulse compression technique was implemented into an ultrasonic system. Golay code was used as a pseudorandom signal in this system, since pair sum of autocorrelations has no sidelobe. The equivalent input pulse of the Golay code was derived to analyze the pulse compression system. Throughout the experiment, the pulse compression technique has demonstrated for its improved SNR(signal to noise ratio) by reducing the system's white noise. And the experimental data also indicated that the SNR enhancement was proportional to the square root of the code length used. The technique seems to perform particularly well with highly energy-absorbent materials such as polymers, plastics and rubbers

Vulnerabilidad energética en la metrópoli de Buenos Aires

Directory of Open Access Journals (Sweden)

Silvina Carrizo

2014-06-01

Full Text Available Argentina declaró el uso racional y la eficacia energética una prioridad nacional, en consonancia con las recomendaciones de la Agencia Internacional de la Energía. Buenos Aires se ha comprometido con varios programas internacionales de preparación al cambio climático. Así a distintas escalas surgen iniciativas para modificar las condiciones y modalidades de aprovisionamiento y consumo energéticos, que revelan la precariedad y vulnerabilidad del sistema y los servicios. Este trabajo presenta una reflexión sobre los cambios que se dan en ese sentido, mostrando los inconvenientes del modelo energético argentino en Buenos Aires y las estrategias o medidas que tienden a revertirlos y a preparar la ciudad para situaciones críticas. En general, se trata de iniciativas que se implementan individual o parcialmente, sin que haya un plan integral promovido a escala colectiva. Las correcciones resultan marginales en el conjunto sin aliviar los problemas que se agravan por el crecimiento vertiginoso de las demandas. Entonces la continuidad del modelo energético argentino basado en hidrocarburos, para abastecer infraestructura que trabaja al límite de su capacidad y servir territorios que no se han preparado para las posibles crisis, explicaría la vulnerabilidad del sistema de abastecimiento metropolitano.

Desarrollo metodológico a partir de mosaicos urbanos para evaluar la eficiencia energética y el aprovechamiento de la energía solar en el marco de la sustentabilidad urbana

Directory of Open Access Journals (Sweden)

Graciela Melisa Viegas

Full Text Available En Argentina, la producción y reciclado de los edificios ha crecido significativamente en los últimos años, correspondiendo el mayor porcentaje a los residenciales. En este sentido es indispensable desarrollar herramientas analíticas que permitan comprender y monitorear los procesos involucrados en el fenómeno de la urbanización y cuantificar sus consecuencias energético-ambientales. El presente trabajo desarrolla una metodología que estudia, a partir de una unidad representativa (mosaico urbano, la aptitud de los distintos sectores de la ciudad para el aprovechamiento energético de la radiación solar en las diferentes texturas urbanas y sus áreas de disipación térmica, determinando el potencial energético de las mismas. Para ello se desarrolla: (a la definición conceptual de "mosaico urbano", su utilidad y su definición técnica; (b la evaluación de las herramientas para el procesamiento, la modelización espacial y energética de mosaicos; y (c un ejemplo de aplicación de la metodología. Los resultados verifican el desarrollo conceptual y la factibilidad de la metodología aplicable a un caso testigo de la ciudad de La Plata, Buenos Aires, Argentina (latitud 34°55 S; longitud 57°57 O, y permiten realizar estimaciones de la potencialidad para hacer eficiente el uso de la energía y aprovechar la energía solar (se obtuvo un 44,3% de ahorro de energía en calefacción.

La Seguridad Energética y la Estrategia Global de Seguridad de la Unión Europea

Directory of Open Access Journals (Sweden)

Ruben Herrero

2016-10-01

Full Text Available El presente artículo plantea una definición ampliada del concepto de seguridad energética, yendo más allá del concepto clásico establecido por la Agencia Internacional de la Energía, incorporando cuestiones relativas a la eficiencia energética, la aceptabilidad del modelo energético y los retos que impone el cambio climático, pero sin perder de perspectiva las exigencias y las dinámicas competitivas económicas globales. Sobre la base de este concepto ampliado, se examina la evolución de la seguridad energética en el marco de la Unión Europea, con una atención particular a cómo se concibe la seguridad energética en la Estrategia Global de Seguridad de 2016.

Iluminación con Energía Solar Fotovoltaica para Autoservicios en Bogotá

Directory of Open Access Journals (Sweden)

Wilmar Giovani Santamaría

2015-07-01

Full Text Available Este artículo presenta un estudio técnico y económico sobre el uso de energía fotovoltaica para iluminación en dos (2 autoservicios en la ciudad de Bogotá. Se analizan diferentes aspectos a tener en cuenta, como la radiación solar mínima sobre el área considerada y los consumos en iluminación con energía convencional. Se estima que, al realizar el cambio de iluminación de bombillos fluorescentes a bombillos LED y establecer como fuente primaria las baterías previamente alimentadas con energía fotovoltaica, se reduce el consumo de energía eléctrica de manera considerable en iluminación. Con esta hipótesis, se plantean tres opciones de sistemas fotovoltaicos autónomos para cada uno de los autoservicios con todos los elementos necesarios para el mejor funcionamiento, el estudio económico de cada opción y un estimativo del ahorro energético.

Broadband 2D electronic spectrometer using white light and pulse shaping: noise and signal evaluation at 1 and 100 kHz.

Science.gov (United States)

Kearns, Nicholas M; Mehlenbacher, Randy D; Jones, Andrew C; Zanni, Martin T

2017-04-03

We have developed a broad bandwidth two-dimensional electronic spectrometer that operates shot-to-shot at repetition rates up to 100 kHz using an acousto-optic pulse shaper. It is called a two-dimensional white-light (2D-WL) spectrometer because the input is white-light supercontinuum. Methods for 100 kHz data collection are studied to understand how laser noise is incorporated into 2D spectra during measurement. At 100 kHz, shot-to-shot scanning of the delays and phases of the pulses in the pulse sequence produces a 2D spectrum 13-times faster and with the same signal-to-noise as using mechanical stages and a chopper. Comparing 100 to 1 kHz repetition rates, data acquisition time is decreased by a factor of 200, which is beyond the improvement expected by the repetition rates alone due to reduction in 1/f noise. These improvements arise because shot-to-shot readout and modulation of the pulse train at 100 kHz enables the electronic coherences to be measured faster than the decay in correlation between laser intensities. Using white light supercontinuum for the pump and probe pulses produces high signal-to-noise spectra on samples with optical densities 200 nm bandwidth.

Short repetition time multiband echo-planar imaging with simultaneous pulse recording allows dynamic imaging of the cardiac pulsation signal.

Science.gov (United States)

Tong, Yunjie; Hocke, Lia M; Frederick, Blaise deB

2014-11-01

Recently developed simultaneous multislice echo-planar imaging (EPI) sequences permit imaging of the whole brain at short repetition time (TR), allowing the cardiac fluctuations to be fully sampled in blood-oxygen-level dependent functional MRI (BOLD fMRI). A novel low computational analytical method was developed to dynamically map the passage of the pulsation signal through the brain and visualize the whole cerebral vasculature affected by the pulse signal. This algorithm is based on a simple combination of fast BOLD fMRI and the scanner's own built-in pulse oximeter. Multiple, temporally shifted copies of the pulse oximeter data (with 0.08 s shifting step and coverage of a 1-s span) were downsampled and used as cardiac pulsation regressors in a general linear model based analyses (FSL) of the fMRI data. The resulting concatenated z-statistics maps show the voxels that are affected as the cardiac signal travels through the brain. Many voxels were highly correlated with the pulsation regressor or its temporally shifted version. The dynamic and static cardiac pulsation maps obtained from both the task and resting state scans, resembled cerebral vasculature. The results demonstrated: (i) cardiac pulsation significantly affects most voxels in the brain; (ii) combining fast fMRI and this analytical method can reveal additional clinical information to functional studies. Copyright © 2013 Wiley Periodicals, Inc.

Perspectivas del potencial energético de la biomasa en el marco global y latinoamericano

Directory of Open Access Journals (Sweden)

Julián Rodrigo Quintero González

2015-06-01

Full Text Available El calentamiento global y los cambios climáticos que éste conlleva han fomentado desde hace algunos años la exploración de otros tipos de obtención energética para disminuir el uso del combustible fósil, siendo éste último uno de los principales causantes de dicho problema ambiental. El presente artículo expone algunas investigaciones recientes sobre la bioenergía u obtención de energía a partir de biomasa, considerada como energía limpia. Se abarcan temáticas como la bioenergía y sus posibilidades desde el punto de vista energético, teniendo en cuenta las expectativas de producción según su potencial o productividad energética, además del aporte que este tipo de tecnología hace a la disminución de la huella ecológica.

Estimación del potencial de energías renovables en el estado de Sonora

Directory of Open Access Journals (Sweden)

Jorge Luis Taddei Bringas

2016-06-01

Full Text Available La etapa de uso de combustibles fósiles está llegando a su fin, debido principalmente a la escasez y problemas de contaminación que originan. En la actualidad existe una marcada tendencia en aprovechar las fuentes renovables de energía, por su bajo impacto ambiental y menor emisión de gases de efecto invernadero (GEI, lo cual contribuye a independizar las políticas energéticas locales de las del mercado global, basadas en la supremacía petrolera. Para obtener el mayor provecho de las energías renovables, es importante determinar el potencial de los distintos recursos energéticos existentes en una región. En este trabajo se presenta una relación del potencial para explotar energías renovables en el estado de Sonora, México, como un paso previo para establecer acciones y políticas que busquen su posible utilización a gran escala.

Pulse amplifier with high 'common mode rejection'

International Nuclear Information System (INIS)

Ijlst, P.

1987-01-01

The input signal of a pulse amplifier contains large 'common-mode' signals which have to be suppressed. A transformer, especially constructed for this purpose, is described. It has been tried to optimize the signal to noise ratio of the pulse amplifier by means of noise analysis. (Auth.)

Suppression of high-frequency perturbations in pulse-width modulation

DEFF Research Database (Denmark)

2008-01-01

A method suppresses high-frequency perturbations in a pulse-width modulated signal. The pulse-width modulation may superpose a carrier signal onto an input signal having a predetermined modulation frequency. The carrier signals may be phase-shifted. The resulting modulated signals may...

A method to reduce the suppression of relevant pulses in pulse weight discriminators

International Nuclear Information System (INIS)

Schwartz, P.

1975-01-01

The pulse height analyzer is used, for instance, with proportional counters. Pulses are broken down into amplitude ranges in accordance with their maximum amplitudes. In pulse height analyzers with real time analog-digital conversion only one deadtime is needed for the respective range selected. For this purpose, all discriminator thresholds of the amplitude stores connected parallel are actuated as an input pulse arrives. The leading edges of the discriminator signals set the amplitude range flip-flop. Only the flip-flop circuit of the maximum amplitude range reached remains set whilst all the others are erased. The trailing edge of the discriminator signals actuates the evaluation of the information stored by the flip-flop circuit selected. It triggers a pulse extender and resets the flip-flop selected. Therefore, only the amplitude range selected needs a deadtime. The pulse extender in addition reduces the processing time of the analyzer by the output pulse length. The characteristic used for the trailing edge is the backward count of the real time analog-digital converter. (DG/RF) [de

Signal anomaly detection and characterization

International Nuclear Information System (INIS)

Morgenstern, V.M.; Upadhyaya, B.R.; Gloeckler, O.

1988-08-01

As part of a comprehensive signal validation system, we have developed a signal anomaly detector, without specifically establishing the cause of the anomaly. A signal recorded from process instrumentation is said to have an anomaly, if during steady-state operation, the deviation in the level of the signal, its root-mean-square (RMS) value, or its statistical distribution changes by a preset value. This deviation could be an unacceptable increase or a decrease in the quantity being monitored. An anomaly in a signal may be characterized by wideband or single-frequency noise, bias error, pulse-type error, nonsymmetric behavior, or a change in the signal bandwidth. Various signatures can be easily computed from data samples and compared against specified threshold values. We want to point out that in real processes, pulses can appear with different time widths, and at different rates of change of the signal. Thus, in characterizing an anomaly as a pulse-type, the fastest pulse width is constrained by the signal sampling interval. For example, if a signal is sampled at 100 Hz, we will not be able to detect pulses occurring at kHz rates. Discussion with utility and Combustion Engineering personnel indicated that it is not practical to detect pulses having a narrow time width. 9 refs., 11 figs., 8 tabs

Energía de oleaje en la isla de Tenerife

OpenAIRE

Imaz Gómez, Mario

2016-01-01

El objeto de este proyecto es realizar todos los estudios necesarios para la construcción de la primera fase de un parque de dispositivos de extracción de energía undimotriz que permita obtener información fiable y necesaria sobre el comportamiento de los dispositivos en grupo y poder ver si el rendimiento es el esperado para posteriormente realizar las otras dos fases con el fin de abastecer a la ciudad de Puerto de la Cruz, situada en el norte de la isla de Tenerife. Actualmente las energía...

A novel algorithm to separate motion artifacts from photoplethysmographic signals obtained with a reflectance pulse oximeter.

Science.gov (United States)

Yao, Jianchu; Warren, Steve

2004-01-01

Pulse oximeters are mainstays for acquiring blood oxygen saturation in static environments such as hospital rooms. However, motion artifacts prevent their broad in wearable, ambulatory environments. To this end, we present a novel algorithm to separate the motion artifacts from plethysmographic data gathered by pulse oximeters. This algorithm, based on the Beer-Lambert law, requires photoplethysmographic data acquired at three excitation wavelengths. The algorithm can calculate venous blood oxygen saturation (SvO2) as well as arterial blood oxygen saturation (SaO2). Preliminary results indicate that the extraction of the venous signal, which is assumed to be most affected by motions, is successful with data acquired from a reflectance-mode sensor.

Pulse-shaping mechanism in colliding-pulse mode-locked laser diodes

DEFF Research Database (Denmark)

Bischoff, Svend; Sørensen, Mads Peter; Mørk, J.

1995-01-01

The large signal dynamics of passively colliding pulse mode-locked laser diodes is studied. We derive a model which explains modelocking via the interplay of gain and loss dynamics; no bandwidth limiting element is necessary for pulse formation. It is found necessary to have both fast and slow...... absorber dynamics to achieve mode-locking. Significant chirp is predicted for pulses emitted from long lasers, in agreement with experiment. The pulse width shows a strong dependence on both cavity and saturable absorber length. (C) 1995 American Institute of Physics....

Evaluation of arterial stiffness by finger-toe pulse wave velocity: optimization of signal processing and clinical validation.

Science.gov (United States)

Obeid, Hasan; Khettab, Hakim; Marais, Louise; Hallab, Magid; Laurent, Stéphane; Boutouyrie, Pierre

2017-08-01

Carotid-femoral pulse wave velocity (PWV) (cf-PWV) is the gold standard for measuring aortic stiffness. Finger-toe PWV (ft-PWV) is a simpler noninvasive method for measuring arterial stiffness. Although the validity of the method has been previously assessed, its accuracy can be improved. ft-PWV is determined on the basis of a patented height chart for the distance and the pulse transit time (PTT) between the finger and the toe pulpar arteries signals (ft-PTT). The objective of the first study, performed in 66 patients, was to compare different algorithms (intersecting tangents, maximum of the second derivative, 10% threshold and cross-correlation) for determining the foot of the arterial pulse wave, thus the ft-PTT. The objective of the second study, performed in 101 patients, was to investigate different signal processing chains to improve the concordance of ft-PWV with the gold-standard cf-PWV. Finger-toe PWV (ft-PWV) was calculated using the four algorithms. The best correlations relating ft-PWV and cf-PWV, and relating ft-PTT and carotid-femoral PTT were obtained with the maximum of the second derivative algorithm [PWV: r = 0.56, P < 0.0001, root mean square error (RMSE) = 0.9 m/s; PTT: r = 0.61, P < 0.001, RMSE = 12 ms]. The three other algorithms showed lower correlations. The correlation between ft-PTT and carotid-femoral PTT further improved (r = 0.81, P < 0.0001, RMSE = 5.4 ms) when the maximum of the second derivative algorithm was combined with an optimized signal processing chain. Selecting the maximum of the second derivative algorithm for detecting the foot of the pressure waveform, and combining it with an optimized signal processing chain, improved the accuracy of ft-PWV measurement in the current population sample. Thus, it makes ft-PWV very promising for the simple noninvasive determination of aortic stiffness in clinical practice.

Eficiencia energética en el sector residencial de la ciudad de Cuenca, Ecuador

OpenAIRE

Baquero Larriva, María Teresa; Quesada Molina, Juan Felipe

2016-01-01

El objetivo de la presente investigación fue determinar en qué medida se puede reducir el consumo de energía en el sector residencial de la ciudad de Cuenca, manteniendo óptimas condiciones de confort. El estudio se centra en la definición de indicadores de eficiencia energética para la vivienda, mediante la determinación de la demanda de energía y la definición de los factores de mayor consumo, usando un enfoque cualitativo y cuantitativo. Se realizaron encuestas en 280 viviendas del sector ...

Evaluación del potencial energético del oleaje en la costa sur del Golfo de México

Directory of Open Access Journals (Sweden)

Alejandro González-Carrillo

2015-01-01

Full Text Available Hallar nuevas fuentes de energía es uno de los retos que trajo consigo el siglo XXI. En este tr abajo se hace un análisis sobre la energía de las olas, la cual presenta varia s ventajas significativas con r especto a otras fuentes de energ ías basadas en combustibles fós iles e, inclusive, otras fuentes renovables de energía. De entre estas ventajas de stacan el bajo impacto ambiental y su alta densidad energética, respectivamente. La energía de las olas del mar se considera ca da vez en más países como un recurso renovable importante y sob re todo prometedor. El objetivo de este trabajo es la evaluación del po tencial energético de las olas en la costa sur del Golfo de Méx ico; en él se observó el comportamiento del olea je y se obtuvo que la potenci a media anual disponible es de 55.91 W/m. Adicionalmente, se de staca el comportamiento estacional de las olas en la región; pues, en es te punto, la estación más energética es otoño y la menos energé tica es primavera, lo cual difiere de la tendencia mundial, en la que i nvierno y verano son la más y la menos energética, respectivamente.

Implicaciones ambientales de las tecnologías de energía renovable

Directory of Open Access Journals (Sweden)

Jan Mahirt-Smith

2011-12-01

Full Text Available Las tecnologías de energía renovable como la eólica, la solar y la biomasa, hacen un uso del suelo más intenso que las de combustibles fósiles tradicionales y, geográficamente, sus implicaciones ambientales son más heterogéneas, por lo que presentan un gran desafío para las técnicas de evaluación de su ciclo de vida. Este trabajo presenta los resultados de una investigación bibliográfica alrededor de los siguientes temas: 1 cambios en el uso del suelo debido a la mayor producción de energía renovable; 2 impactos del uso de suelo; 3 variabilidad geográfica en el inventario de datos; y 4 efectos de la distribución de energía. Además, se revisa el grado de investigación que actualmente se aplica acerca de las tecnologías de energía renovable en campos como el eólico, el solar y la bioenergía y en la evaluación del ciclo de vida en general.

Actividad económica, consumo final de energía y requerimientos de energía primaria en Cataluña, 1990-2005. Análisis mediante el uso de los balances energéticos desde una perspectiva input-output

OpenAIRE

Jordi Roca Jusmet; Vicent Alcántara Escolano; Emilio Padilla Rosa

2007-01-01

Este trabajo analiza la evolución de los consumos finales de energía en Cataluña durante el periodo 1990-2005. En conjunto, los consumos finales de energía crecen por encima del crecimiento del PIB en términos reales. La disponibilidad actual de datos permite una desagregación en cinco actividades: sector primario; sector industrial; sector servicios; transporte; y sector doméstico. Los aumentos relativos más importantes se dan en los sectores servicios, doméstico y transporte. Es esta última...

Radiation signatures from a locally energized flaring loop

International Nuclear Information System (INIS)

Emslie, A.G.; Vlahos, L.; and Institute for Plasma Research, Stanford University)

1980-01-01

We calculate the radiation signatures from a locally energized solar flare loop, at a variety of wavelengths. Our calculations depend strongly on the physical properties of the energy release mechanism which we qualitatively discuss

Application of pulsed OSL to polymineral fine-grained samples

International Nuclear Information System (INIS)

Feathers, James K.; Casson, M. Aksel; Schmidt, Amanda Henck; Chithambo, Makaiko L.

2012-01-01

Pulsed OSL is applied to nine fine-grained sediment samples from Sichuan province, China, using stimulating pulses of 10 μs on and 240 μs off, with an infrared exposure prior to each OSL measurement. Comparison of fading rates between pulsed and non-pulsed signals, the latter also obtained with a preceding IR exposure, shows that fading is significant for mainly the non-pulsed signals. Presence of a pulsed IRSL and the magnitudes of b-value to correct for lower alpha efficiency suggest that pulsing does not fully remove a significant feldspar signal, only a fading component. Comparison with ages of quartz extracts shows that pulsed OSL ages are consistent, while CW-OSL ages are slightly older and CW-IRSL ages are much older. The older ages suggest a less well-bleached feldspar component.

The influence of laser pulse duration and energy on ICP-MS signal intensity, elemental fractionation, and particle size distribution in NIR fs-LA-ICP-MS

Science.gov (United States)

Diwakar, Prasoon K.; Harilal, Sivanandan S.; LaHaye, Nicole L.; Hassanein, Ahmed; Kulkarni, Pramod

2015-01-01

Laser parameters, typically wavelength, pulse width, irradiance, repetition rate, and pulse energy, are critical parameters which influence the laser ablation process and thereby influence the LA-ICP-MS signal. In recent times, femtosecond laser ablation has gained popularity owing to the reduction in fractionation related issues and improved analytical performance which can provide matrix-independent sampling. The advantage offered by fs-LA is due to shorter pulse duration of the laser as compared to the phonon relaxation time and heat diffusion time. Hence the thermal effects are minimized in fs-LA. Recently, fs-LA-ICP-MS demonstrated improved analytical performance as compared to ns-LA-ICP-MS, but detailed mechanisms and processes are still not clearly understood. Improvement of fs-LA-ICP-MS over ns-LA-ICP-MS elucidates the importance of laser pulse duration and related effects on the ablation process. In this study, we have investigated the influence of laser pulse width (40 fs to 0.3 ns) and energy on LA-ICP-MS signal intensity and repeatability using a brass sample. Experiments were performed in single spot ablation mode as well as rastering ablation mode to monitor the Cu/Zn ratio. The recorded ICP-MS signal was correlated with total particle counts generated during laser ablation as well as particle size distribution. Our results show the importance of pulse width effects in the fs regime that becomes more pronounced when moving from femtosecond to picosecond and nanosecond regimes. PMID:26664120

Variaciones de voltaje: Mala calidad de la energía

Directory of Open Access Journals (Sweden)

Norberto Rodríguez Barallobre

2011-02-01

Full Text Available Este es el primero de una serie de artículos encaminados a tratar la creciente problemática de la calidadde la energía en las instalaciones industriales debida al incremento del uso de la electrónica y suscomponentes contaminantes de la energía eléctrica entendida como el producto de la onda de corriente yla de voltaje. Además, se ofrece un procedimiento para estimar el costo de las pérdidas técnicas ytecnológicas por concepto de una mala calidad de la energía así como, algunas recomendaciones paramitigar estas pérdidas millonarias en el sector industrial.  This is a first of a series of papers toward to treat the power quality growing problematical in industrialinstallations networks, due to increasing use of electronic and its polluting components, learned as aproduct of the current and voltage wave, Also is offered a procedure to estimate the technical andtechnological losses cost due to the low quality energy, some recommendations to mitigate this millonairelosses in the industrial sector

El desarrollo de las energías renovables y el paisaje: algunas bases para la implementación de la Convención Europea del Paisaje en la Política energética española

Directory of Open Access Journals (Sweden)

Marina Frolova

2008-01-01

Full Text Available Desde el inicio del proceso de reforma de la política energética de la Unión Europea, los paisajes emergentes a partir de generación de electricidad con energías renovables suscitan un interés creciente. España se caracteriza por una implantación muy exitosa de las políticas europeas en materia de energías renovables. Sin embargo, la proliferación de aerogeneradores y placas fotovoltaicas en espacios agrícolas o improductivos conlleva la destrucción de numerosos paisajes muy valiosos. Por lo que la nueva sensibilidad hacia los paisajes se está convirtiendo en el mayor obstáculo para el desarrollo de las energías renovables. El objetivo de este artículo es explorar en la relación que se establece entre la implantación de las energías renovables y la evolución de las políticas paisajísticas. Para ello, se analiza el desarrollo que han experimentado las políticas de energías renovables en Europa y en España; se estudian las nuevas formas democráticas de gestión del territorio que plantea la Convención Europea del Paisaje. Por último, se tratan determinados temas de la inclusión del paisaje en las políticas de energías renovables en España, comentando algunos ejemplos en los que se detectan nuevas estrategias en la implantación de proyectos de energías renovables que pueden reducir los impactos sobre el paisaje.

Use of the Frank sequence in pulsed EPR

DEFF Research Database (Denmark)

Tseitlin, Mark; Quine, Richard W.; Eaton, Sandra S.

2011-01-01

The Frank polyphase sequence has been applied to pulsed EPR of triarylmethyl radicals at 256MHz (9.1mT magnetic field), using 256 phase pulses. In EPR, as in NMR, use of a Frank sequence of phase steps permits pulsed FID signal acquisition with very low power microwave/RF pulses (ca. 1.5m......W in the application reported here) relative to standard pulsed EPR. A 0.2mM aqueous solution of a triarylmethyl radical was studied using a 16mm diameter cross-loop resonator to isolate the EPR signal detection system from the incident pulses. Keyword: Correlation spectroscopy,Multi-pulse EPR,Low power pulses,NMR,EPR...

Importancia de la energía para el crecimiento económico de México

Directory of Open Access Journals (Sweden)

Flory A. Dieck Assad

2014-01-01

Full Text Available Esta investigación analiza la productividad agregada de la mano de obra y del capital en México entre los años 1993 y 2013, con el fin de identificar las variables que influyen en su comportamiento, especialmente la energía. Esto se lleva a cabo mediante una función de producción agregada que logra identificar la influencia del acervo utilizado de capital, el trabajo remunerado, los cambios tecnológicos y la energía sobre la productividad agregada real promedio de la mano de obra y el capital y, por ende, del crecimiento potencial del PIB (producto interno bruto. Asimismo, se introduce el tema de precios de la energía, identificando su impacto directo en el uso de energía y el indirecto en la productividad y el crecimiento económico. Este análisis culmina con la definición de las perspectivas de la Reforma energética a la luz de los resultados de esta investigación, vislumbrando los desafíos y retos futuros.

The effect of pulsed electric fields on the electrotactic migration of human neural progenitor cells through the involvement of intracellular calcium signaling.

Science.gov (United States)

Hayashi, Hisamitsu; Edin, Fredrik; Li, Hao; Liu, Wei; Rask-Andersen, Helge

2016-12-01

Endogenous electric fields (EFs) are required for the physiological control of the central nervous system development. Application of the direct current EFs to neural stem cells has been studied for the possibility of stem cell transplantation as one of the therapies for brain injury. EFs generated within the nervous system are often associated with action potentials and synaptic activity, apparently resulting in a pulsed current in nature. The aim of this study is to investigate the effect of pulsed EF, which can reduce the cytotoxicity, on the migration of human neural progenitor cells (hNPCs). We applied the mono-directional pulsed EF with a strength of 250mV/mm to hNPCs for 6h. The migration distance of the hNPCs exposed to pulsed EF was significantly greater compared with the control not exposed to the EF. Pulsed EFs, however, had less of an effect on the migration of the differentiated hNPCs. There was no significant change in the survival of hNPCs after exposure to the pulsed EF. To investigate the role of Ca 2+ signaling in electrotactic migration of hNPCs, pharmacological inhibition of Ca 2+ channels in the EF-exposed cells revealed that the electrotactic migration of hNPCs exposed to Ca 2+ channel blockers was significantly lower compared to the control group. The findings suggest that the pulsed EF induced migration of hNPCs is partly influenced by intracellular Ca 2+ signaling. Copyright © 2016 Elsevier B.V. All rights reserved.

[Improved detection of the pulse oximeter signal with a digital nerve block in patients in poor health status].

Science.gov (United States)

Cordoví de Armas, L; Espinaco Valdés, J; Jiménez Paneque, R E; Costa Hidalgo, T; Vallongo Menéndez, M B

2008-10-01

To demonstrate the efficacy of a digital nerve block for improving pulse oximetry in conditions of low tissue perfusion. A randomized single-blind study of adult patients undergoing surgery under general anesthesia for conditions characterized by hypoperfusion. Patients were assigned to a control group or an experimental group. The experimental group received a digital nerve block in the middle finger of the left hand; a sensor was then placed on the finger for between 120 and 300 minutes. Age, sex, diagnosis, total observation time (TOT), percentage of time with no pulse oximeter signal (NoPO), and percentage of time with an unstable pulse oximeter signal (UnstPO) were recorded. Each patient was questioned between 16 and 24 hours after surgery and was examined for flushing, paresthesia, hypoesthesia, pain, and ecchymosis. The chi2 test was used to compare dichotomized or nominal variables and the t test was used to compare age, TOT, NoPO, and UnstPO. Values of P<.05 were considered statistically significant in both cases. Fifty patients were randomized to each group. A total of 82 patients remained in the study (control group=42, experimental group=40). There were no significant between-group differences in diagnoses or TOT. The mean values for NoPO and UnstPO were higher in the control group than in the experimental group (11.1% vs 4.4% and 35.9% vs 15.7%, respectively; P<.001). A digital nerve block can be used to prevent pulse oximetry failures in conditions of low peripheral perfusion.

Energía eólica en Argentina : un análisis económico del derecho

Directory of Open Access Journals (Sweden)

Cecilia Giralt

2013-10-01

Full Text Available El abastecimiento energético con base en fuentes no renovables es un tema altamente estratégico en las agendas de los Estados. El petróleo se está agotando y probablemente las existencias comprobadas no alcanzarán para abastecer el consumo mundial, provocando una serie de impactos sociopolíticos y económicos a nivel global. Esto ha llevado a los gobiernos a replantear sus matrices energéticas, apostando a las energías renovables como un camino posible para lograr una mayor autonomía energética. La Argentina, con una matriz energética desbalanceada e hidrocarburo-dependiente, se ha visto empujada también a reformular su horizonte energético a partir de fuentes renovables para lograr una mayor independencia del recurso fósil. Los marcos regulatorios utilizados para este cambio son el objeto de análisis de este artículo, el cual también intenta contribuir con algunas recomendaciones para un futuro muy cercano.

Problemas institucionales de las energías renovables en México

OpenAIRE

Samuel Brugger; Ma. Elena Nancy Dávila Moreno; Manuel Francisco Llamas Galván

2011-01-01

Este ensayo trata de explicar los problemas institucionales y jurídicos que han limitado el aprovechamiento de dichas energías alternativas. El trabajo presenta la situación actual de México; después analiza el potencial que tiene el país. De ahí se pasa al estudio de la problemática institucional y jurídica que no ha logrado fomentar la promoción de energías renovables en México.

Problemas institucionales de las energías renovables en México

Directory of Open Access Journals (Sweden)

Samuel Brugger

2011-09-01

Full Text Available Este ensayo trata de explicar los problemas institucionales y jurídicos que han limitado el aprovechamiento de dichas energías alternativas. El trabajo presenta la situación actual de México; después analiza el potencial que tiene el país. De ahí se pasa al estudio de la problemática institucional y jurídica que no ha logrado fomentar la promoción de energías renovables en México.

En cumplimiento con la orden ejecutiva del presidente Trump sobre la Independencia Energética

Science.gov (United States)

Acciones reglamentarias tomadas por la EPA, incluyendo audiencias públicas, para implementar la Orden Ejecutiva sobre la Independencia Energética y la propuesta derogación del Plan de Energía Limpia.

Herbal Energizers: Speed By Any Other Name.

Science.gov (United States)

Jenkins, Andrew P.

This guide focuses on over-the-counter (OTC) stimulants sold to high school aged athletes and dieters as "herbal energizers," food supplements, and fatigue reducers. While advertising often makes them appear healthful and harmless, all of these stimulants belong in the class "sympathomimetic amines," so called because they…

Perspectivas de la situación energética mundial. Las oportunidades para Colombia

OpenAIRE

Arturo Infante Villarreal

2007-01-01

Casi la cuarta parte de la energía que consume Estados Unidos proviene de petróleo importado y sólo el 6% se origina en fuentes renovables, aunque el país produce 20% de la polución ambiental mundial y tiene sólo 4% de la población total. Los biocombustibles son una fuente potencial de energía renovable para Estados Unidos, y el resto del mundo, porque tienen un balance energético y ambiental bastante favorable. Si las condiciones de precios son adecuadas para los productores de las materias ...

Asturias en el sistema energético: del nacionalismo a la globalización

OpenAIRE

Maurín Álvarez, Manuel

2011-01-01

Con una demanda energética regional estancada y al mismo tiempo en que se clausuran las últimas explotaciones mineras, principales proveedoras de materias primas energéticas autóctonas, Asturias se aventura a la construcción de infraestructuras de generación y transporte que permitirían duplicar en los próximos años una producción eléctrica que ya es excedentaria. La región se convierte así en una especie de «vientre de alquiler» energético, especializada en generar, con materias primas impor...

Mejora de la eficiencia energética en una vivienda

OpenAIRE

Díaz Oliva, Marc

2013-01-01

El objetivo de este proyecto es la mejora de la eficiencia energética de la vivienda este objetivo me viene por una estancia en Alemania donde todas las viviendas están concebidas para obtener la máxima eficiencia y por consiguiente ahorro una de las cosas que más me llamo la atención fue la implantación de energías renovables ya que las horas de luz son menores a las obtenidas en España por este motivo quise comprobar cuanto se podía mejorar la eficiencia en mi vivienda y s...

Cómo producen energía las células

OpenAIRE

Carlos Alberto Ordoñez

2014-01-01

El adenosín trifosfato (ATP), es la moneda energética de los seres vivos. Para poder ser sintetizado, los organismos requieren oxidar los sustratos energéticos de la dieta, proteínas, grasas y carbohidratos. Inicialmente estas sustancias tienen vías metabólicas separadas hasta alcanzar en su degradación un metabolito común que es el acetil CoA. A partir de este punto entran al ciclo de Krebs, con producción de CO2 e hidrogeniones, estos últimos se transportan por óxido reducción a la cadena r...

Gaussian Pulse-Based Two-Threshold Parallel Scaling Tone Reservation for PAPR Reduction of OFDM Signals

Directory of Open Access Journals (Sweden)

Lei Guan

2011-01-01

Full Text Available Tone Reservation (TR is a technique proposed to combat the high Peak-to-Average Power Ratio (PAPR problem of Orthogonal Frequency Division Multiplexing (OFDM signals. However conventional TR suffers from high computational cost due to the difficulties in finding an effective cancellation signal in the time domain by using only a few tones in the frequency domain. It also suffers from a high cost of hardware implementation and long handling time delay issues due to the need to conduct multiple iterations to cancel multiple high signal peaks. In this paper, we propose an efficient approach, called two-threshold parallel scaling, for implementing a previously proposed Gaussian pulse-based Tone Reservation algorithm. Compared to conventional approaches, this technique significantly reduces the hardware implementation complexity and cost, while also reducing signal processing time delay by using just two iterations. Experimental results show that the proposed technique can effectively reduce the PAPR of OFDM signals with only a very small number of reserved tones and with limited usage of hardware resources. This technique is suitable for any OFDM-based communication systems, especially for Digital Video Broadcasting (DVB systems employing large IFFT/FFT transforms.

Numerical Analysis of Through Transmission Pulsed Eddy Current Testing and Effects of Pulse Width Variation

International Nuclear Information System (INIS)

Shin, Young Kil; Choi, Dong Myung

2007-01-01

By using numerical analysis methods, through transmission type pulsed eddy current (PEC) testing is modeled and PEC signal responses due to varying material conductivity, permeability, thickness, lift-off and pulse width are investigated. Results show that the peak amplitude of PEC signal gets reduced and the time to reach the peak amplitude is increased as the material conductivity, permeability, and specimen thickness increase. Also, they indicate that the pulse width needs to be shorter when evaluating the material conductivity and the plate thickness using the peak amplitude, and when the pulse width is long, the peak time is found to be more useful. Other results related to lift-off variation are reported as well

Estudio de la energía y el medio ambiente: una propuesta didáctica computarizada

Directory of Open Access Journals (Sweden)

Edwin Francisco Bonza Camargo

2009-09-01

Full Text Available El objetivo de este proyecto es desarrollar un material educativo computarizado, MEC, para la enseñanza de la energía; contribuyendo de esta manera a solucionar una de las grandes falencias del sistema educativo colombiano: la falta de material didáctico en las aulas de las escuelas y colegios. Además, con la aplicación de este material se aporta a la creación de conciencia en la población escolar hacia un uso más racional de la energía en pro del medio ambiente. El software se diseñó con base en el manejo de lecturas, imágenes, sonidos, videos y animaciones que permiten al estudiante aprender y conceptuar con mayor facilidad sobre un tema tan importante como lo es el de los recursos energéticos renovables y no renovables, abarcando temas tan importantes como la energía solar térmica, que es una posible solución a la crisis energética que se avecina. También, resalta la importancia que tiene la búsqueda de nuevas fuentes de energía que no degraden el medio ambiente.

Development of high electrical resistance persistent current switch for high speed energization system

International Nuclear Information System (INIS)

Jizo, Y.; Furuta, Y.; Nakashima, H.

1986-01-01

Japanese National Railways is now developing a superconducting magnetically-levitated train system. A persistent current switch is incorporated in the super-conducting magnet used in the magnetically-levitated train. In recent years, the switch has been required to have higher electrical resistance during its off-state in order to realize the high speed energization/de-energization system of the superconducting magnets. The system aims to decrease evaporation volume of liquid helium during the energization/de-energization of the magnet, by means of energizing the superconducting magnet with high current increasing/decreasing rate. Consequently, it would be possible to decrease the dependence of the on-board magnet system upon the ground cooling system. Through the development of a stable superconductive wire material and a coil structure for the persistent current switch using many small model switches which were produced in order to improve their current carrying capacities, the authors have succeeded in manufacturing the high electrical resistance persistent current switch whose electrical resistance was 5 ohms. The switch, of cylindrical shape, has a diameter of about 100mm, a length of about 100mm. These 5 ohm PCSs are now functioning in stable conditions being incorporated in the superconducting magnets of No.2 vehicle of MLU001 at the JNR's Miyazaki test track. Further, the authors are now developing the PCS of still higher resistance values, such as 50 ohms, through studies for stabilization in structural aspects of the winding and obtaining results therefrom

Gas exchange and leaf contents in bell pepper under energized water and biofertilizer doses

Directory of Open Access Journals (Sweden)

Francisca R. M. Borges

2016-06-01

Full Text Available ABSTRACT The objective of this study was to evaluate the effect of energized water and bovine biofertilizer doses on the gas exchange and NPK contents in leaves of yellow bell pepper plants. The experiment was conducted at the experimental area of the Federal University of Ceará, in Fortaleza-CE, Brazil, from June to November 2011. The experiment was set in a randomized block design, in a split-plot scheme; the plots were composed of treatments with energized and non-energized water and the subplots of five doses of liquid biofertilizer (0, 250, 500, 750 and 1000 mL plant-1 week-1. The following variables were analyzed: transpiration, stomatal conductance, photosynthesis and leaf contents of nitrogen (N, phosphorus (P and potassium (K. Water energization did not allow significant increases in the analyzed variables. The use of biofertilizer as the only source of fertilization was sufficient to provide the nutrients N, P and K at appropriate levels for the bell pepper crop.

Redes de energía en la Argentina del siglo XXI. Proyectos locales innovadores

Directory of Open Access Journals (Sweden)

Silvina Carrizo

2015-04-01

Full Text Available En Argentina se construyeron de forma pionera, extensas redes de electricidad, gas y combustibles. El 98% de los hogares están conectados a la red eléctrica y el 51% de la población tiene acceso al gas natural por red (INDEC 2012. A pesar de la cobertura energética amplia, aún persisten en el país algunas regiones -como el Noroeste de la Provincia de Buenos Aires NOBAdonde las redes no llegan o tienen menor densidad. La región NOBA, situada entre las ciudades de Rosario y Buenos Aires, que cuentan con infraestructura considerable para su aprovisionamiento, presenta redes eléctricas y gasíferas poco densas -especialmente hacia el interior- y escaso desarrollo de fuentes de energías alternativas. En materia de gas, faltan gasoductos troncales o regionales. En el sistema eléctrico, hay poca capacidad de generación y se necesita mayor interconexión. Desde distintos niveles se han promovido alternativas en materia de producción, transporte y distribución de energía, pero los avances aún no alcanzan para asegurar la resiliencia energética enla región NOBA. En un contexto de esta índole, actores locales se han organizado para satisfacer sus necesidades energéticas con proyectos nuevos de transporte de gas y de aprovechamiento de recursos locales renovables, con un potencial que aún no ha sido puesto en valor. Abordando proyectos energéticos locales y regionales, este trabajo propone reflexionar acerca de la nueva geografía que podría delinearse en la producción y circulación de la energía, más flexible, fiable y sustentable, fomentando la innovación y la productividad, así como la equidad regional.

Evaluation of pulse oximeter derived photoplethysmographic signals for obstructive sleep apnea diagnosis.

Science.gov (United States)

Li, Yan; Gao, He; Ma, Yan

2017-05-01

High prevalence of obstructive sleep apnea (OSA) has increased the demands for more convenient and accessible diagnostic devices other than standard in-lab polysomnography (PSG). Despite the increasing utility of photoplethysmograph (PPG), it remains understudied in underserved populations. This study aimed to evaluate the reliability of a standard pulse oximeter system with an automated analysis based on the PPG signal for the diagnosis of OSA, as compared with PSG derived measures.Consecutive out-patients with suspect OSA completed a PPG monitoring simultaneous with an overnight in-lab standard PSG. Forty-nine OSA patients (38 males, age 43.5 ± 16.9 years, BMI 26.9 ± 0.5 kg/m) were included in this study. Automated analyses were based on PPG and oximetry signals only. The PPG calculated measures were compared with PSG derived measures for agreement tests.Respiratory events index derived from PPG significantly correlated with PSG-derived apnea-hypopnea index (r = 0.935, P oximeter system with PPG recording can be used for the diagnosis or screening of OSA in high risk population.

Estimativa das necessidades energéticas em pacientes com doença renal crônica

Directory of Open Access Journals (Sweden)

Juliana Cordeiro Dias Rodrigues

2013-02-01

Full Text Available Estabelecer as necessidades energéticas de pacientes com doença renal crônica é importante para que se possam tratar os distúrbios nutricionais encontrados nessa população. Segundo os guias de condutas voltados ao cuidado nutricional de pacientes com essa doença, a recomendação energética pode variar entre 30 e 40kcal/kg/dia. Contudo, trabalhos que avaliaram os componentes do gasto energético nos pacientes com doença renal crônica sugerem que as necessidades energéticas dessa população podem diferir do valor recomendado acima, a depender da condição clínica (presença de comorbidades, da modalidade de tratamento empregado e do nível de atividade física. Dessa forma, o presente trabalho tem como objetivo fazer uma revisão dos estudos sobre o gasto energético de pacientes com doença renal crônica, com o intuito de abordar as seguintes questões: (1 as atuais recomendações de energia para pacientes com doença renal crônica estão adequadas? (2 qual equação de predição poderia ser empregada para estimar as necessidades energéticas desse grupo de pacientes? Assim, esta revisão busca auxiliar o nutricionista ao estimar as necessidades energéticas de pacientes com doença renal crônica.

Costo energético de muros y techos utilizados en la zona sur de Tamaulipas

Directory of Open Access Journals (Sweden)

Mireya Alicia Rosas Lusett

2015-01-01

Full Text Available El presente trabajo muestra los procedimientos y resultados obtenidos del análisis de la energía trasmitida en techos y muros de las viviendas seleccionadas de la zona sur del estado de Tamaulipas, una de las cinco áreas establecidas dentro del proyecto “Desarrollo y validación de una metodología para estimar los impactos en el ahorro de energía por el uso de sistemas pasivo-constructivos en la edificación para diferentes climas de México”. Este proyecto fue financiado por la Convocatoria S0019-2009-01 del Fondo Sectorial de Sustentabilidad Energética SENER-CONACYT con registro Nº 118665, cuyo objetivo en su tercera etapa de ejecución, consistió en hacer uso de la herramienta Ener-Habitat, la cual fue desarrollada durante la segunda fase del proyecto. Con dicho programa de cálculo se determinaron los gastos de energía, comparativa de cuatro sistemas constructivos para muros y tres sistemas constructivos para losas utilizadas en la zona sur de Tamaulipas. Con la información obtenida y mediante el uso de la metodología desarrollada para estimar los impactos en el ahorro de energía, se evaluó el costo energético de cada uno de los sistemas constructivos. Con los resultados obtenidos se pudo determinar cuál era el muro y techo de menor gasto de energía para la zona de estudio. Adicionalmente se realizó un estudio de la influencia de la absortancia solar de la superficie exterior de los muros, cuyos resultados darán la pauta para diseñar una vivienda que pretende sea adecuada y cómoda al clima cálido húmedo que prevalece en el área.

A photodiode amplifier system for pulse-by-pulse intensity measurement of an x-ray free electron laser.

Science.gov (United States)

Kudo, Togo; Tono, Kensuke; Yabashi, Makina; Togashi, Tadashi; Sato, Takahiro; Inubushi, Yuichi; Omodani, Motohiko; Kirihara, Yoichi; Matsushita, Tomohiro; Kobayashi, Kazuo; Yamaga, Mitsuhiro; Uchiyama, Sadayuki; Hatsui, Takaki

2012-04-01

We have developed a single-shot intensity-measurement system using a silicon positive-intrinsic-negative (PIN) photodiode for x-ray pulses from an x-ray free electron laser. A wide dynamic range (10(3)-10(11) photons/pulse) and long distance signal transmission (>100 m) were required for this measurement system. For this purpose, we developed charge-sensitive and shaping amplifiers, which can process charge pulses with a wide dynamic range and variable durations (ns-μs) and charge levels (pC-μC). Output signals from the amplifiers were transmitted to a data acquisition system through a long cable in the form of a differential signal. The x-ray pulse intensities were calculated from the peak values of the signals by a waveform fitting procedure. This system can measure 10(3)-10(9) photons/pulse of ~10 keV x-rays by direct irradiation of a silicon PIN photodiode, and from 10(7)-10(11) photons/pulse by detecting the x-rays scattered by a diamond film using the silicon PIN photodiode. This system gives a relative accuracy of ~10(-3) with a proper gain setting of the amplifiers for each measurement. Using this system, we succeeded in detecting weak light at the developmental phase of the light source, as well as intense light during lasing of the x-ray free electron laser. © 2012 American Institute of Physics

Proyecto de vivienda energéticamente sostenible situada en Ontinyent (Valencia). Instalación fotovoltaica.

OpenAIRE

MOLLÁ CALABUIG, SERGIO

2015-01-01

[ES] Se van a diseñar las instalaciones necesarias para que una vivienda unifamiliar sea energéticamente sostenible. La única fuente de energía disponible es la solar Se calcualrán las instalaciones para dos opciones. 1. Vivienda conectada a la red eléctrica general. 2. Vivienda aislada de la red eléctrica. [ES] El objeto de este trabajo es el diseño y comparación, de las instalaciones necesarias para que una vivienda unifamiliar sea energéticamente sostenible, con la única fuen...

Estimación del potencial de energías renovables en el estado de Sonora

OpenAIRE

Jorge Luis Taddei Bringas; María de los Ángeles Navarrete Hinojosa; Pablo Daniel Taddei Arriola; Rafael Cabanillas López.

2016-01-01

La etapa de uso de combustibles fósiles está llegando a su fin, debido principalmente a la escasez y problemas de contaminación que originan. En la actualidad existe una marcada tendencia en aprovechar las fuentes renovables de energía, por su bajo impacto ambiental y menor emisión de gases de efecto invernadero (GEI), lo cual contribuye a independizar las políticas energéticas locales de las del mercado global, basadas en la supremacía petrolera. Para obtener el mayor provecho de las energía...

La vulnerabilidad energética asociada a la movilidad motorizada

Directory of Open Access Journals (Sweden)

Ana Sanz Fernández

2013-04-01

Full Text Available ResumenEl concepto de vulnerabilidad energética describe la situación a la que se pueden enfrentar aquellos niveles de renta cuyo patrón de movilidad deje de ser económicamente viable por el incremento de los costes del petróleo. Teniendo en cuenta que la movilidad laboral es un gasto prioritario para evitar la exclusión social que supone la pérdida del empleo, el aumento de los gastos en esa partida presupuestaria familiar puede derivar en dos situaciones, ambas involuntarias, que serían la necesidad de destinar una mayor cantidad de recursos al transporte (pudiendo entonces aparecer privaciones en otras esferas o la obligación de cambiar los patrones de movilidad. El objetivo de esta investigación es desarrollar este concepto, ponerlo en relación con dos conceptos directamente vinculados, exclusión social vinculada al transporte y pobreza energética, y aplicar en el área metropolitana de Madrid la metodología desarrollada, detectando los de espacios urbanos energéticamente vulnerables y explicitando las relaciones de este fenómeno con la disciplina.Palabras claveVulnerabilidad energética, exclusión social vinculada al transporte, pobreza energética, pico del petróleo, área metropolitana.AbstractThe concept of energy vulnerability describes the situation that may face those income levels that have a mobility pattern which is no longer economically viable due to rising oil costs. Given that labor mobility is a priority spending to avoid social exclusion caused by job loss, increased expenses in that family budget can result in two situations, both involuntary, that would be the need for a greater amount of resources to transport (in that case, deprivation can then appear in other areas or the obligation to change mobility patterns. The objective of this research is todevelop this concept, put on two concepts directly related, transport related social exclusion and fuel poverty, and applied in the Madrid metropolitan area

CAMAC-compatible differential pulse discriminator-counter

International Nuclear Information System (INIS)

Tselikov, I.V.

1988-01-01

A differential pulse discriminator-counter for a Moessbauer spectrometer is described. Input pulses are collected according to the following algorithm; a pulse is admitted into the channel depending on whether or not the preceding pulse fell into the discrimination window. The circuit does not contain delay lines to allow for the delay lines to allow for the delay of the signal from the upper-level discriminator with respect to the signal from the lower-level discriminator due to the finite rise time of the input pulses, which makes it possible to reduce the dead time of the discriminator to the actuation time of the threshold circuits. The pulse count rate is 150 MHz, the input amplitude is +/-3 V, the dead time is 6 nsec, and the delay from input to output is 14 nsec. The unit is CAMAC-compatible

Signal processing for radiation detectors

CERN Document Server

Nakhostin, Mohammad

2018-01-01

This book provides a clear understanding of the principles of signal processing of radiation detectors. It puts great emphasis on the characteristics of pulses from various types of detectors and offers a full overview on the basic concepts required to understand detector signal processing systems and pulse processing techniques. Signal Processing for Radiation Detectors covers all of the important aspects of signal processing, including energy spectroscopy, timing measurements, position-sensing, pulse-shape discrimination, and radiation intensity measurement. The book encompasses a wide range of applications so that readers from different disciplines can benefit from all of the information. In addition, this resource: * Describes both analog and digital techniques of signal processing * Presents a complete compilation of digital pulse processing algorithms * Extrapolates content from more than 700 references covering classic papers as well as those of today * Demonstrates concepts with more than 340 origin...

Modelo para la Predicción Energética de una Instalación Hotelera

Directory of Open Access Journals (Sweden)

Adriana V. Acosta

2011-10-01

Full Text Available Resumen: Este artículo describe la obtención y validación de un modelo de predicción energética para el hotel Meliá Habana de la ciudad Habana en Cuba. El modelo obtenido emplea el método de series de tiempo radiantes para la determinación de la carga térmica de los bloques habitacionales de la instalación. El modelo es implementado en el lenguaje de programación MatLab®. La validación experimental del modelo se realiza con mediciones reales del consumo energético diario del hotel. El valor de uso del modelo obtenido es apreciable para estudios de comportamiento energético y para la implementación de estrategias avanzadas de control. Palabras clave: Modelado, Control de la Energía, Coeficientes de Temperatura, Validación

Monitoring, Analyzing and Assessing Radiation Belt Loss and Energization

Science.gov (United States)

Daglis, I.; Balasis, G.; Bourdarie, S.; Horne, R.; Khotyaintsev, Y.; Mann, I.; Santolik, O.; Turner, D.; Anastasiadis, A.; Georgiou, M.; Giannakis, O.; Papadimitriou, C.; Ropokis, G.; Sandberg, I.; Angelopoulos, V.; Glauert, S.; Grison, B., Kersten T.; Kolmasova, I.; Lazaro, D.; Mella, M.; Ozeke, L.; Usanova, M.

2013-09-01

We present the concept, objectives and expected impact of the MAARBLE (Monitoring, Analyzing and Assessing Radiation Belt Loss and Energization) project, which is being implemented by a consortium of seven institutions (five European, one Canadian and one US) with support from the European Community's Seventh Framework Programme. The MAARBLE project employs multi-spacecraft monitoring of the geospace environment, complemented by ground-based monitoring, in order to analyze and assess the physical mechanisms leading to radiation belt particle energization and loss. Particular attention is paid to the role of ULF/VLF waves. A database containing properties of the waves is being created and will be made available to the scientific community. Based on the wave database, a statistical model of the wave activity dependent on the level of geomagnetic activity, solar wind forcing, and magnetospheric region will be developed. Multi-spacecraft particle measurements will be incorporated into data assimilation tools, leading to new understanding of the causal relationships between ULF/VLF waves and radiation belt dynamics. Data assimilation techniques have been proven as a valuable tool in the field of radiation belts, able to guide 'the best' estimate of the state of a complex system. The MAARBLE (Monitoring, Analyzing and Assessing Radiation Belt Energization and Loss) collaborative research project has received funding from the European Union’s Seventh Framework Programme (FP7-SPACE-2011-1) under grant agreement no. 284520.

The random signal generator of imitated nuclear radiation pulse

International Nuclear Information System (INIS)

Li Dongcang; Yang Lei; Yuan Shulin; Yang Yinghui; Zang Fujia

2007-01-01

Based in pseudo-random uniformity number, it produces random numbers of Gaussian distribution and exponential distribution by arithmetic. The hardware is the single-chip microcomputer of 89C51. Program language makes use of Keil C. The output pulse amplitude is Gaussian distribution, exponential distribution or uniformity distribution. Likewise, it has two mode or upwards two. The time alternation of output pulse is both periodic and exponential distribution. The generator has achieved output control of multi-mode distribution, imitated random characteristic of nuclear pulse in amplitude and in time. (authors)

Liga de magnésio como material para bateria de alta densidade energética

OpenAIRE

Munhoz, Igor Polezi

2014-01-01

Orientador: Prof. Dr. Jorge Tomioka Dissertação (mestrado) - Universidade Federal do ABC, Programa de Pós-Graduação em Engenharia Elétrica, 2014. No contexto energético, as mudanças climáticas e as crescentes crises energéticas aumentaram as preocupações e as pesquisas na área de acumuladores de energia, visando alcançar melhorias no cenário energético e ambiental global. Ao mesmo tempo, a sociedade tornou-se dependente do consumo de energia elétrica, sendo que falhas no fornec...

Pulse-to-pulse variations in accreting X-ray pulsars

Directory of Open Access Journals (Sweden)

Kretschmar Peter

2014-01-01

Full Text Available In most accreting X-ray pulsars, the periodic signal is very clear and easily shows up as soon as data covering sufficient pulse periods (a few ten are available. The mean pulse profile is often quite typical for a given source and with minor variations repeated and recognisable across observations done years or even decades apart. At the time scale of individual pulses, significant pulse-to-pulse variations are commonly observed. While at low energies some of these variations might be explained by absorption, in the hard X-rays they will reflect changes in the accretion and subsequent emission. The amount of these variations appears to be quite different between sources and contains information about the surrounding material as well ass possibly interactions at the magnetosphere. We investigate such variations for a sample of well-known sources.

Sampling system for fast single pulses; Realisation d'un dispositif d'echantillonnage d'un signal bref unique

Energy Technology Data Exchange (ETDEWEB)

Zenatti, D [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1969-07-01

Development of a device for the enlargement of the domain of application of classical oscilloscopes to the observation of fast single pulses by application of the sampling principle. Its principal characteristics are: Bandwidth of 700 MHz; Maximum sensibility of 50 mV; Maximum amplitude of input signal of {+-} 1 V; Number of samples of 16; Samples separation of 0,2 ns. (author) [French] Realisation d'un dispositif permettant d'elargir le domaine d'utilisation des oscilloscopes classiques en appliquant le principe de l'echantillonnage a l'observation d'un signal bref unique. Les principales caracteristiques sont les suivantes: Bande passante de 700 MHz; Sensibilite maximale de 50 mV; Amplitude maximale du signal a echantillonner de {+-} 1 V; Nombre de points d'echantillonnage de 16; Pas d'echantillonnage de 0,2 ns. (auteur)

Proyecto de vivienda energéticamente sostenible situada en Almería. Instalación fotovoltaica.

OpenAIRE

CORBERÁ FERRANDO, JOSÉ Mª

2015-01-01

[ES] Se van a diseñar las instalaciones necesarias para que una vivienda unifamiliar sea energéticamente sostenible. La única fuente de energía disponible es la solar Se calcualrán las instalaciones para dos opciones. 1. Vivienda conectada a la red eléctrica general. 2. Vivienda aislada de la red eléctrica. Corberá Ferrando, JM. (2015). Proyecto de vivienda energéticamente sostenible situada en Almería. Instalación fotovoltaica. http://hdl.handle.net/10251/53541. TFGM

Comparative Analysis of the Clinical Significance of Oscillatory Components in the Rhythmic Structure of Pulse Signal in the Diagnostics of Psychosomatic Disorders in School Age Children.

Science.gov (United States)

Desova, A A; Dorofeyuk, A A; Anokhin, A M

2017-01-01

We performed a comparative analysis of the types of spectral density typical of various parameters of pulse signal. The experimental material was obtained during the examination of school age children with various psychosomatic disorders. We also performed a typological analysis of the spectral density functions corresponding to the time series of different parameters of a single oscillation of pulse signals; the results of their comparative analysis are presented. We determined the most significant spectral components for two disordersin children: arterial hypertension and mitral valve prolapse.

Celdas combustibles: una opción para la transformación descentralizada de energía

Directory of Open Access Journals (Sweden)

Julio Alberto Gavilán Yodú

2011-02-01

Full Text Available La solución a los problemas energéticos actuales y al progresivo deterioro del medio ambiente está estrechamenterelacionada con la elección de sistemas energéticos alternativos que sean capaces de garantizar el desarrollosostenible de todos los países. La producción descentralizada de energía, fundamentada con acierto por losdefensores del denominado camino energético suave o el camino del Sol, permite la transformación de energíacon tecnologías preferentemente no contaminantes en el lugar de consumo. Con esto se reducirían de modoconsiderable las pérdidas energéticas ocasionadas por los procesos de transmisión y distribución. La celdacombustible constituye la tecnología de mayor potencial para revolucionar el panorama energético en este siglo.Como transformador electroquímico, la conversión energética máxima posible se define por la energía libre dereacción en un régimen de temperatura relativamente bajo. En este trabajo se realiza un análisis de los diferentestipos de celdas combustibles y se caracteriza el estado actual de esta tecnología. Además, se analiza el usodel hidrógeno solar en celdas combustibles.  The solution to the actual energy problems and to the progressive damage of the environment is closely relatedwith the election of alternative energy systems that it be able to guarantee the sustainable development of all thecountries. The decentralized energy production, based with success by the defenders of the one denominatedsoft energy way or Sun way, allows the energy transformation with technologies preferably not pollutants in theplace of  consumption. It would decrease in a considerable way the energy losses caused by the transmissionprocesses and distribution. The fuel cell constitutes the technology of more potential to revolutionize the energypanorama in this century. As electrochemical transformer, the possible maximum energy conversion is definedfor the free energy of reaction in a relatively

Limitaciones para el desarrollo de energías renovables en Argentina

OpenAIRE

Marina Yesica Recalde; Daniel Hugo Bouille; Leónidas Osvaldo Girardin

2015-01-01

En las últimas décadas las energías renovables han cobrado impulso a nivel mundial con un significativo impacto sobre el desarrollo sustentable de las naciones. Si bien diferentes trabajos analizan la eficiencia de políticas e instrumentos para la promoción de dichas fuentes, la mayoría de las veces se deja de lado el análisis de cómo el contexto en el cual las políticas son implementadas determina su performance. En este trabajo se analiza el desarrollo de las energías renovables en el merca...

Productividad y eficiencia energética en el proceso de molienda del mineral laterítico

Directory of Open Access Journals (Sweden)

Olga Angulo-Leblanch

2000-03-01

Full Text Available En el trabajo se realiza un análisis energético del proceso de molienda seca del mineral laterítico, considerado como el proceso de mayor consumo de energía eléctrica entre los procesos beneficiadores que se emplean en las plantas niquelíferas, ubicadas al norte de la provincia de Holguín. Son analizadas las particularidades energéticas que exhibe este proceso cuando las máquinas trabajan normalmente con la presencia de mineral y cuando se producen ausencias ocasionales de éste en el sistema, lo que trae como consecuencia el incremento notable de las potencias demandadas por los molinos y por los ventiladores de recirculación . Se analiza además, la influencia del grado de llenado con bolas del molino, sobre la productividad y la estrecha relación de esta última con la eficiencia energética del proceso. El método fundamental de análisis empleado, se basa en la obtención experimental y en las condiciones concretas de explotación, de las características energéticas de las unidades de molienda y de sus agregados, como vía directa para descubrir las reservas de energía del sistema y conocer hasta qué punto es posible mejorar su eficiencia influyendo sobre la productividad. El trabajo revela que, cuando las unidades de molienda son operadas con valores de productividades que oscilan entre un 50 y un 60% de la nominal, si son adoptadas las medidas pertinentes para lograr el aumento de la productividad, entonces esto puede reportar hasta un 55% de mejoramiento de la eficiencia energética del proceso.

Monitoreo energético y estrategias de RETROFIT para viviendas sociales en clima frío.

Directory of Open Access Journals (Sweden)

Micaela Andersen

2017-12-01

Full Text Available El presente trabajo aborda la aplicación de tecnologías y pautas para el reciclado masivo de viviendas urbanas representativas. Se evalúa aquí el comportamiento energético actual en una vivienda social “tipo” con un alto nivel de replicabilidad. Para ello, se cuantifica el potencial ahorro energético al aplicar diversas estrategias de mejoramiento de la envolvente edilicia que permitan arribar a valores admisibles de pérdidas térmicas, de acuerdo con la normativa argentina. Se describe la tecnología, el comportamiento térmico y energético de una vivienda perteneciente al barrio “645 Viviendas” (desarrollado por El Instituto de Planificación y Promoción de la Vivienda, ubicada en la ciudad de San Carlos de Bariloche, en la zona bioambiental IV, muy fría. Este barrio presenta una emergencia energética de gran magnitud, ya que no se encuentra conectado a la red de gas natural. Posteriormente, se examinan los resultados de la auditoria energética de 2016 y se muestra la simulación térmica realizada en Ecotect Analysis 2011, incorporando las condiciones reales de uso auditadas. Ajustado el modelo, se analizan 24 estrategias de mejoramiento de la envolvente térmica, posibilitando la identificación de las estrategias de mayor impacto en la reducción de la demanda energética.

Certificación energética de edificios en España y sus implicaciones económicas

Directory of Open Access Journals (Sweden)

Ruá, M. J.

2012-09-01

Full Text Available Under the European Energy Performance of Buildings Directive, the Member States must develop methods to certify energy efficiency of buildings. Calener-VYP v1.0 is the only Spanish official tool to certify a high energy efficiency performance of residential buildings, through the general option. It has two indicators implemented, CO₂ emissions and primary energy consumption. However, in the process of energy rating a building, only the CO₂ emissions indicator is considered. The economic consequences of this are studied, by means of simulating real properties with different construction assemblies and building services in the twelve Spanish climatic zones and calculating their costs. The results show that having a better energy rate in Calener VYP does not necessarily entail a lower consumption cost. Therefore, it is necessary to include the annual primary energy consumption indicator, because its absence involves that costs cannot be used as an argument when promoting energy efficiency among users.

Bajo la Directiva Europea sobre eficiencia energética de los edificios, los Estados Miembros deben desarrollar procedimientos para certificar energéticamente los edificios. Calener-VYP v1.0 es la única herramienta oficial española para certificar una elevada aptitud en eficiencia energética de edificios residenciales, por el método general. Tiene dos indicadores implementados, emisiones de CO₂ y consumo de energía primaria. Sin embargo, en el proceso de otorgar la calificación energética, solamente se consideran las emisiones de CO₂. Las implicaciones económicas de esto se estudian simulando viviendas con diferentes características constructivas e instalaciones en las doce zonas climáticas españolas y calculando sus costes. Los resultados muestran que una mejor calificación energética en Calener-VYP no implica necesariamente un menor coste de consumo energético. Por tanto, es necesario

Avaliação energética de um sistema integrado de abastecimento de água

Directory of Open Access Journals (Sweden)

Ana Luiza Rezende Guanais

2017-07-01

Full Text Available RESUMO Os encargos energéticos decorrentes do Sistema Integrado de Abastecimento de Água de Feira de Santana (SIAA-FSA foram analisados utilizando o método de avaliação do ciclo de vida. Foram identificadas, na cadeia de abastecimento de água, as etapas do sistema com maiores encargos energéticos, e propostos cenários de melhoria. Cadeias de produção dos insumos químicos, transporte dos insumos, energia elétrica e substituição dos tubos na rede para a manutenção do SIAA-FSA foram consideradas. A demanda energética acumulada do SIAA-FSA foi de 3,51 kWh.m-3 de água consumida. As etapas de captação e distribuição de água apresentaram os maiores consumos energéticos, e a eletricidade do bombeamento representou 86% da demanda energética acumulada. Os cenários propostos para o SIAA-FSA apresentaram melhorias significativas em relação ao cenário atual, com usos mais racionais de insumos químicos, eletricidade e água.

El papel de la energía renovable en la competitividad un bosquejo de México

Directory of Open Access Journals (Sweden)

Laura Leticia Laurent Martínez

2016-03-01

Full Text Available La relación entre la energía y el desarrollo parece incuestionable. Entre más energía y más requerimientos tecnológicos haya que poner en juego para producirla, más avanzados se consideran los países. Sin embargo, los criterios están cambiando aceleradamente, aunque sin las repercusiones esperadas por los defensores de la competitividad. En este artículo se presenta un panorama global del bienestar de los seres vivos mediante la sustitución de las energías provenientes de los fósiles y de la fisión nuclear por energía renovable (er. Se prosigue con una serie de argumentaciones sobre el papel que desempeñan las energías renovables en la competitividad sustentable en relación con la competitividad efímera. Finalizamos con una breve descripción de la posición de México en el renglón de la er, la cual ofrece un marco para una reflexión crítica de las restricciones de la sustentabilidad en México

Effectiveness of Pulse Oximetry Versus Doppler for Tourniquet Monitoring.

Science.gov (United States)

Wall, Piper L; Buising, Charisse M; Grulke, Lisa; Troester, Alexander; Bianchina, Nicholas; White, Shannon; Freymark, Rosemarie; Hassan, Ali; Hopkins, James W; Renner, Catherine Hackett; Sahr, Sheryl M

Pulse oximeters are common and include arterial pulse detection as part of their methodology. The authors investigated the possible usefulness of pulse oximeters for monitoring extremity tourniquet arterial occlusion. Tactical Ratcheting Medical Tourniquets were tightened to the least Doppler-determined occluding pressure at mid-thigh or mid-arm locations on one limb at a time on all four limbs of 15 volunteers. A randomized block design was used to determine the placement locations of three pulse oximeter sensors on the relevant digits. The times and pressures of pulsatile signal absences and returns were recorded for 200 seconds, with the tourniquet being tightened only when the Doppler ultrasound and all three pulse oximeters had pulsatile signals present (pulsatile waveform traces for the pulse oximeters). From the first Doppler signal absence to tourniquet release, toe-located pulse oximeters missed Doppler signal presence 41% to 50% of the times (discrete 1-second intervals) and missed 39% to 49% of the pressure points (discrete 1mmHg intervals); fingerlocated pulse oximeters had miss rates of 11% to 15% of the times and 13% to 19% of the pressure points. On toes, the pulse oximeter ranges of sensitivity and specificity for Doppler pulse detection were 71% to 90% and 44% to 51%, and on fingers, the respective ranges were 65% to 77% and 78% to 83%. Use of a pulse oximeter to monitor limb tourniquet effectiveness will result in some instances of an undetected weak arterial pulse being present. If a pulse oximeter waveform is obtained from a location distal to a tourniquet, the tourniquet should be tightened. If a pulsatile waveform is not detected, vigilance should be maintained. 2017.

Generation of on-line test signals for nuclear instrumentation for PFBR

International Nuclear Information System (INIS)

Ram, Rajit; Bhatnagar, P.V.; Rajesh, M.G.; Das, Debashis

2010-01-01

Neutron flux monitoring system for PFBR employs pulse signal processing in start up and intermediate power range of reactor operation and Campbell signal processing in intermediate and full power range of reactor operation. Pulse signal processing unit as well as Campbell signal processing unit incorporates FPGA that generates pulse/white noise signal for on-line testing and diagnostic of the channels. In pulse channel fixed/linearly/exponentially varying pulse rate signal is generated over three decades of reactor operation. In the Campbell channel, Poisson distributed noise varying linearly/exponentially is generated over four decades of reactor operation. Multiple numbers of Poisson distributed random pulse trains are summed and amplified to get the white noise signal. Exponentially increasing gain pattern, generated by MATLAB is used to increase the RMS value of the generated noise. The paper discuses the successful testing and validation of pulse and Campbell channel by making use of the generated pulse/white noise signal over wide range of operation for nuclear instrumentation. (author)

Evaluación energética y validación matemática de un sistema de conversión de energía por rozamiento

OpenAIRE

Barona Díaz, Santiago Xavier

2016-01-01

El presente trabajo, consiste en la Evaluación Energética y validación Matemática de un nuevo dispositivo de calentamiento, que aprovecha la alta energía calórica producida por la fricción y el aplastamiento de un anillo cilíndrico de aleación Cu-Sn. En este proceso de transformación mecánico térmica, a temperaturas de trabajo sobre los 800ºC intervienen características tales como el área de la pared conductiva, torque, velocidad de rotación, fuerza axial de compresión, tipo de materiales, qu...

An Economical Fast Discriminator for Nuclear Pulse Counting

International Nuclear Information System (INIS)

Issarachai, Opas; Punnachaiya, Suvit

2009-07-01

Full text: This research work was aimed to develop a fast discriminator at low cost but high capability for discrimination a nanosecond nuclear pulse. The fast discriminator can be used in association with fast photon counting system. The designed structure consisted of the ultra-fast voltage comparator using ADCMP601 integrated circuit, the monostable multivibrator with controllable pulse width output by propagation delay of logic gate, and the fast response buffer amplifier. The tested results of pulse height discrimination of 0-5 V nuclear pulse with 20 ns (FWHM) pulse width showed the correlation coefficient (R 2 ) between discrimination level and pulse height was 0.998, while the pulse rate more than 10 MHz could be counted. The 30 ns logic pulse width output revealed high stable and could be smoothly driven to low impedance load at 50 Ω. For pulse signal transmission to the counter, it was also found that the termination of reflected signal must be considered because it may cause pulse counting error

La utilización eficaz del hormigón térmico en rehabilitación energética de edifcios

OpenAIRE

Moraño Rodríguez, Alfonso Javier

2016-01-01

Como sabrá el lector, se ha establecido en España por consecuencia de la Directiva 2012/27/ UE, un Programa de Ayudas para la Rehabilitación Energética de Edificios existentes (Programa PAREER-CRECE) con el fin de incentivar y promover la realización de actuaciones de reforma que favorezcan el ahorro energético, la mejora de la eficiencia energética, el aprovechamiento de las energías renovables y la reducción de emisiones de dióxido de carbono. El Ministerio de Industria, Energía y Turismo, ...

Using pulse oximetry to account for high and low frequency physiological artifacts in the BOLD signal.

Science.gov (United States)

Verstynen, Timothy D; Deshpande, Vibhas

2011-04-15

The BOLD signal not only reflects changes in local neural activity, but also exhibits variability from physiological processes like cardiac rhythms and breathing. We investigated how both of these physiological sources are reflected in the pulse oximetry (PO) signal, a direct measure of blood oxygenation, and how this information can be used to account for different types of noise in the BOLD response. Measures of heart rate, respiration and PO were simultaneously recorded while neurologically healthy participants performed an eye-movement task in a 3T MRI. PO exhibited power in frequencies that matched those found in the independently recorded cardiac and respiration signals. Using the phasic and aphasic properties of these signals as nuisance regressors, we found that the different frequency components of the PO signal could be used to identify different types of physiological artifacts in the BOLD response. A comparison of different physiological noise models found that a simple, down-sampled version of the PO signal improves the estimation of task-relevant statistics nearly as well as more established noise models that may run the risk of over-parameterization. These findings suggest that the PO signal captures multiple sources of physiological noise in the BOLD response and provides a simple and efficient way of modeling these noise sources in subsequent analysis. Copyright © 2011 Elsevier Inc. All rights reserved.

Modelo de cooperación energética entre China y América Latina

OpenAIRE

Hongbo, Sun

2014-01-01

Las relaciones entre China y América Latina han tenido más implicaciones estratégicas en la actual transición de poder político y económico internacional, en particular, sus vínculos energéticos han sido testigos de grandes avances de cooperación entre industrias de petróleo y gas. La cooperación energética de China con América Latina se compone, en una parte nada despreciable, de cambios en curso en energía en el occidente del hemisferio. Las compañías petroleras chinas recurren a diferentes...

Análisis de sistema de conversores fluido-dinámicos de energía renovable para la Patagonia Austral de Argentina

Directory of Open Access Journals (Sweden)

Carlos Victor Manuel Labriola

2014-06-01

Full Text Available El potencial de energía en mares y océanos se puede clasificar de distintas formas, por ejemplo: * La energía de las mareas ó Mareomotriz * La energía de las corrientes marinas * La energía de las olas ó Undimotriz * La energía térmica oceánica (OTEC. De estas formas de energía oceánica, tres son posibles en la zona Atlántica de nuestra Patagonia Austral, la Mareomotriz, la Undimotriz y la de corrientes marinas. La Energía Mareomotriz se da desde Viedma hasta Tierra del Fuego con amplitudes de mareas de 4m hasta 20m, la Energía de las Olas se da en la costa de Chubut y Santa Cruz con potenciales de 10 a 30kW/m lineal de frente de ola y el aprovechamiento de las corrientes marinas se puede dar en lugares puntuales como ser la desembocadura del río Deseado o la de Río Gallegos. Para estas Fuentes de Energía se está realizando un banco de pruebas de modelos conversores de las mismas a Energía Eléctrica, en la Unidad Académica Caleta Olivia (UACO de la Universidad Nacional de la Patagonia Austral (UNPA. Este banco dispondrá de dos canales de ensayos hidrodinámicos uno para energía de las corrientes marinas y otro para las olas. El primero dispondrá de una bomba de circulación con velocidad de fluido variable entre 0 y 4m/s. El banco para olas tendrá un sistema de batido del agua para producir ondas de amplitud y período variable. Además se están dimensionando dos modelos de conversores de energía oceánica. Uno es una turbina, tipo eólica sumergida y el otro modelo es de tubo electromecánico oscilante como conversor energético de las olas.

Diseño metodológico de la evaluación de proyectos energéticos bajo incertidumbre en precios: caso de cogeneración de energía en una empresa en Cali

Directory of Open Access Journals (Sweden)

Carlos Andrés Núñez Viveros

2013-01-01

Full Text Available Los recursos energéticos en la industria recobran mayor relevancia en su competitividad, representando el se- gundo o tercer rubro en el costo. El comportamiento fluctuante de los costos históricos, así como la incertidum- bre de su tendencia futura, acentuada por la inminencia del desmonte del impuesto de contribución en energía eléctrica (20% de la tarifa, conllevan el cuestionamiento de si los proyectos de cogeneración de energía tendrán viabilidad en un futuro cercano. El presente trabajo desarrolla una metodología innovadora para evaluar la via- bilidad de la implementación de proyectos de cogeneración, fundamentada en 3 simuladores que trabajan con información estadística y proyecciones matemáticas, además de realizar un análisis de sensibilidad del proyecto a los comportamientos proyectados de los precios futuros de la energía eléctrica y de los combustibles.

Una solución al problema de la energía y de la contaminación en México

Directory of Open Access Journals (Sweden)

Dieter Klaus

1975-01-01

Full Text Available La crisis energética ha demostrado mundialmente que nuestro concepto de "energía" es insostenible. se necesitan tres unidades caloríficas provenientes del petróleo o el carbón para producir una unidad de energía eléctrica superior. Menos favorable es el aprovechamiento en la conversión del combustible en movimiento de nuestros vehículos. La obtención de energía proveniente del aceite crudo es irreversible.

Integración energética: una incertidumbre regulatoria

Directory of Open Access Journals (Sweden)

María de la Cruz Bayá C.

2006-01-01

Full Text Available Este artículo pretende introducir en la reflexión de los elementos que están insertos hoy por hoy en la agenda de la integración energética, como uno de los baluartes más importantes para la consolidación de los procesos subregionales ya que establece, per se, la base de la nueva configuración de las relaciones interestatales a partir de la relación de oferta y demanda energética. En este sentido, los métodos utilizados en la presente investigación han sido el exegético, comparado, estudio de caso y bibliográfico, lo cual ha permitido concluir que se requiere de la generación de un marco regulatorio comunitario armonizado, vinculado a los principios de supranacionalidad y de sustentabilidad.

Análisis DAFO del sector de la energía eólica en España

Directory of Open Access Journals (Sweden)

López-Vico, Victoria

2009-06-01

Full Text Available a energía eólica se ha convertido en un sector económico y energético clave en la actualidad, tanto en España como en el resto del mundo. Con el objetivo de saber si ésta energía puede responder a las necesidades de demanda energética, siendo una energía sustitutiva a los tradicionales combustibles fósiles, hemos realizado un análisis DAFO, donde se muestran las debilidades, amenazas, fortalezas y oportunidades de este sector en auge.Wind power has become a very important economic and power sector, as much in Spain as in the rest of the world. With the aim of knowing if this energy can respond to the energetic demand, being a substitute energy to traditional fossil fuels, we have realised a SWOT analysis, where we can know the strengths, threats, opportunities and weaknesses of this sector in full expansion.

Transformer inrush current reduction through sequential energization for wind farm applications

Energy Technology Data Exchange (ETDEWEB)

Abdulsalam, S.; Xu, W. [Alberta Univ., Edmonton, AB (Canada)

2008-07-01

Wind power is considered as one of the fastest growing technologies in the power industry. The electrical configuration of a wind farm consists of long spans of medium voltage collector feeders. Each wind generator is connected to the collector circuit/feeder through either a pad mount oil filled, or a nacelle-mounted dry type transformer. All collector feeders connect to a single collector substation where the connection to the high-voltage transmission is established through a step up transformer. With a large number of wind generators per feeder, large inrush current will flow due to simultaneous transformer energization which can cause high voltage sag at the point of common coupling. Wind farms are generally located in unpopulated remote areas where no access to strong network connection is feasible. It is common to have the PCC on a relatively weak location on the sub-transmission/distribution network. In order to meet interconnection standards requirements, the amount of voltage sag due to the energization of a number of transformers needs to be evaluated. This paper presented an effective solution to the mitigation of inrush currents and associated voltage sag for wind farm applications. The paper presented a diagram of a typical configuration of a wind farm electrical distribution system and also described the analytical methodologies for the evaluation of inrush current level together with simulation results. A simplified analysis and sizing criteria for the associated neutral resistor size was presented. It was concluded that the scheme could significantly reduce inrush current level when a large number of transformers are simultaneously energized. The presented application eliminates the need to sectionalize feeders, thereby simplifying them for the energization process. 6 refs., 5 figs.

La Reforma Energética: a 20 años del TLCAN

OpenAIRE

Vargas, Rosío

2015-01-01

La visita del presidente estadounidense Barack Obama a México, en mayo de 2013, fue la ocasión para buscar el acceso al petróleo y gas mexicano, amparado en el argumento de los 20 años del TLCAN, bajo "la necesidad" de su relanzamiento. Cabilderos nacionales y extranjeros se dieron a la tarea de elaborar la estrategia para la apertura total del sector energético mexicano bajo la propuesta de la Reforma Energética mexicana, aprobada el 20 de diciembre de 2013. En las modificaciones constitucio...

Sustentabilidad empresarial, seguridad energética y ética ambiental en Chile

OpenAIRE

Suárez,Andrés

2013-01-01

El artículo explora la relación entre sustentabilidad empresarial -asociada tanto a la rentabilidad financiera como a las relaciones con colectivos locales- y el medioambiente, en el contexto de una economía internacionalizada como la chilena. Asimismo, analiza conflictos recientes originados en Chile para la provisión de energía y las dificultades en la definición de una matriz energética, y, finalmente, la influencia de la ética ecológica para la preservación de los ecosistemas de alta biod...

Lifetime cost effectiveness of a through-school nutrition and physical programme: Project Energize.

Science.gov (United States)

Rush, Elaine; Obolonkin, Victor; McLennan, Stephanie; Graham, David; Harris, James D; Mernagh, Paul; Weston, Adéle R

2014-01-01

Project Energize, a multicomponent through-school physical activity and nutrition programme, is delivered to all primary school children in the Waikato region. The programme aim is to improve the overall health and reduce the rate of weight gain of all Waikato primary school children. An existing economic model was used to extrapolate the programme effects, initial costs, lifetime health treatment cost structures, quality-adjusted-life-years gained and increased life expectancy to the general and Māori child population of New Zealand. In March 2011, a sample of 2474 younger (7.58 ± 0.57 years, mean ± SD) and 2330 older (10.30 ± 0.51 years) children (36% Māori) attending Energize schools had body mass index measured and compared using mixed effect modelling with unEnergized comparison children from 2004 and 2006 from the same region. In 2011 the median body mass index reduction compared with the comparison younger children was -0.504 (90% CI -0.435 to -0.663) kg/m(2) and in the older children -0.551 (-0.456 to -0.789) kg/m(2). In 2010 there were 42,067 children attending Energize schools and in the same year NZ$1,891,175 was spent to deliver the programme; a cost of $44.96/child/year. Compared to the comparison children the increment in cost/quality-adjusted-life-year gained was $30,438 for the younger and $24,690 for the older children, and lower for Māori (younger $28,241, older $22,151) and for the middle socioeconomic status schools ($23,211, $17,891). Project Energize would improve quality and length of life and when compared with other obesity prevention programmes previously assessed with this model, it would be relatively cost-effective from the health treatment payer's perspective.

Influence of electromagnetic signal of antibiotics excited by low-frequency pulsed electromagnetic fields on growth of Escherichia coli.

Science.gov (United States)

Ke, Yin-Lung; Chang, Fu-Yu; Chen, Ming-Kun; Li, Shun-Lai; Jang, Ling-Sheng

2013-01-01

Energy medicine (EM) provides a new medical choice for patients, and its advantages are the noninvasive detection and nondrug treatment. An electromagnetic signal, a kind of EM, induced from antibiotic coupling with weak, extremely low-frequency pulsed electromagnetic fields (PEMFs) is utilized for investigating the growth speed of Escherichia coli (E. coli). PEMFs are produced by solenoidal coils for coupling the electromagnetic signal of antibiotics (penicillin). The growth retardation rate (GRR) of E. coli is used to investigate the efficacy of the electromagnetic signal of antibiotics. The E. coli is cultivated in the exposure of PEMFs coupling with the electromagnetic signal of antibiotics. The maximum GRR of PEMFs with and without the electromagnetic signal of antibiotics on the growth of E. coli cells in the logarithmic is 17.4 and 9.08%, respectively. The electromagnetic signal of antibiotics is successfully coupled by the electromagnetic signal coupling instrument to affect the growth of E. coli. In addition, the retardation effect on E. coli growth can be improved of by changing the carrier frequency of PEMFs coupling with the electromagnetic signal of antibiotics. GRR caused by the electromagnetic signal of antibiotics can be fixed by a different carrier frequency in a different phase of E. coli growth.

Optic fiber pulse-diagnosis sensor of traditional Chinese medicine

Science.gov (United States)

Ni, J. S.; Jin, W.; Zhao, B. N.; Zhang, X. L.; Wang, C.; Li, S. J.; Zhang, F. X.; Peng, G. D.

2013-09-01

The wrist-pulse is a kind of signals, from which a lot of physiological and pathological status of patients are deduced according to traditional Chinese medicine theories. This paper designs a new optic fiber wrist-pulse sensor that based on a group of FBGs. Sensitivity of the optic fiber wrist-pulse measurement system reaches 0.05% FS and the range reaches 50kPa. Frequency response is from 0 Hz to 5 kHz. A group of typical pulse signal is given out in the paper to compare different status of patient. It will improve quantification of pulse diagnosis greatly.

Design and Implementation of Energized Fracture Treatment in Tight Gas Sands

Energy Technology Data Exchange (ETDEWEB)

Mukul Sharma; Kyle Friehauf

2009-12-31

Hydraulic fracturing is essential for producing gas and oil at an economic rate from low permeability sands. Most fracturing treatments use water and polymers with a gelling agent as a fracturing fluid. The water is held in the small pore spaces by capillary pressure and is not recovered when drawdown pressures are low. The un-recovered water leaves a water saturated zone around the fracture face that stops the flow of gas into the fracture. This is a particularly acute problem in low permeability formations where capillary pressures are high. Depletion (lower reservoir pressures) causes a limitation on the drawdown pressure that can be applied. A hydraulic fracturing process can be energized by the addition of a compressible, sometimes soluble, gas phase into the treatment fluid. When the well is produced, the energized fluid expands and gas comes out of solution. Energizing the fluid creates high gas saturation in the invaded zone, thereby facilitating gas flowback. A new compositional hydraulic fracturing model has been created (EFRAC). This is the first model to include changes in composition, temperature, and phase behavior of the fluid inside the fracture. An equation of state is used to evaluate the phase behavior of the fluid. These compositional effects are coupled with the fluid rheology, proppant transport, and mechanics of fracture growth to create a general model for fracture creation when energized fluids are used. In addition to the fracture propagation model, we have also introduced another new model for hydraulically fractured well productivity. This is the first and only model that takes into account both finite fracture conductivity and damage in the invaded zone in a simple analytical way. EFRAC was successfully used to simulate several fracture treatments in a gas field in South Texas. Based on production estimates, energized fluids may be required when drawdown pressures are smaller than the capillary forces in the formation. For this field

Desarrollo e implantación de energías renovables: situación actual y tendencias

OpenAIRE

Picó Heras, Sergio

2002-01-01

En esta tesina se tratarán las posibilidades que ofrecen las energías renovables com base de una planificicación energética. El tema se enfocará tanto desde puntos de vista económicos, ambientales, técnicos, políticos, etc

A Single-Pulse Integrator

DEFF Research Database (Denmark)

Miller, Arne

1974-01-01

A single-pulse integrator is described. It gives a relative measure of the integral of the output signal from a coil monitor on the Risø 10 MeV linear accelerator, and displays the value on a digital voltmeter. The reproduccibility is found to be better than ±1% for an accelerated pulse charge...

Subharmonic emissions from microbubbles: effect of the driving pulse shape.

Science.gov (United States)

Biagi, Elena; Breschi, Luca; Vannacci, Enrico; Masotti, Leonardo

2006-11-01

The aims of this work are to investigate the response of the ultrasonic contrast agents (UCA) insonified by different arbitrary-shaped pulses at different acoustic pressures and concentration of the contrast agent focusing on subharmonic emission. A transmission setup was developed in order to insonify the contrast agent contained in a measurement chamber. The transmitted ultrasonic signals were generated by an arbitrary wave generator connected to a linear power amplifier able to drive a single-element transducer. The transmitted ultrasonic pulses that passed through the contrast agent-filled chamber were received by a second transducer or a hydrophone aligned with the first one. The radio frequency (RF) signals were acquired by fast echographic multiparameters multi-image novel apparatus (FEMMINA), which is an echographic platform able to acquire ultrasonic signals in a real-time modality. Three sets of ultrasonic signals were devised in order to evaluate subharmonic response of the contrast agent respect with sinusoidal burst signals used as reference pulses. A decreasing up to 30 dB in subharmonic response was detected for a Gaussian-shaped pulse; differences in subharmonic emission up to 21 dB were detected for a composite pulse (two-tone burst) for different acoustic pressures and concentrations. Results from this experimentation demonstrated that the transmitted pulse shape strongly affects subharmonic emission in spite of a second harmonic one. In particular, the smoothness of the initial portion of the shaped pulses can inhibit subharmonic generation from the contrast agents respect with a reference sinusoidal burst signal. It also was shown that subharmonic generation is influenced by the amplitude and the concentration of the contrast agent for each set of the shaped pulses. Subharmonic emissions that derive from a nonlinear mechanism involving nonlinear coupling among different oscillation modes are strongly affected by the shape of the ultrasonic

Design and application of pulse information acquisition and analysis ...

African Journals Online (AJOL)

... two-dimensional information acquisition, multiplex signals combination and deep data mining. Conclusions: The newly developed system could translate the pulse signals into digital, visual and measurable motion information of vessel. Keywords: Visualized pulse information; Radial artery; B mode ultrasound; Traditional ...

Magnet Design and Analysis of a 40 Tesla Long Pulse System Energized by a Battery Bank

Science.gov (United States)

Lv, Y. L.; Peng, T.; Wang, G. B.; Ding, T. H.; Han, X. T.; Pan, Y.; Li, L.

2013-03-01

A 40 tesla long pulse magnet and a battery bank as the power supply have been designed. This is now under construction at the Wuhan National High Magnetic Field Center. The 22 mm bore magnet will generate smooth pulses with duration 1 s and rise time 0.5 s. The battery bank consists of 945 12V/200 Ah lead-acid battery cells. The magnet and battery bank were optimized by codes developed in-house and by ANSYS. The coil was made from soft copper with internal reinforcement by fiber-epoxy composite; it is divided into two sections connected in series. The inner section consists of helix coils with each layer reinforced by Zylon composite. The outer section will be wound from copper sheet and externally reinforced by carbon fiber composite.

La elasticidad de la demanda por electricidad y la política energética

Directory of Open Access Journals (Sweden)

Alexander Galetovic

2010-01-01

Full Text Available En el análisis y la práctica de la política energética se suele suponer que la elasticidad de la demanda por energía eléctrica es irrelevante. Este trabajo muestra que durante episodios de escasez de energía una “pequeña” elasticidad basta para generar caídas “grandes” de la probabilidad de déficit y del costo del abastecimiento eléctrico. Esto se debe a que en la vecindad de la capacidad del sistema, la oferta de energía de corto plazo es cercana a vertical. Ilustramos nuestro punto cuantitativamente simulando la operación esperada del sistema eléctrico chileno durante los años de ajuste a la crisis causada por los cortes de gas argentinos, el periodo 2006-2010. Mostramos que el aumento de los precios causado por el retraso de las inversiones y los cortes de gas argentino, combinado con una “pequeña” elasticidad de la demanda mensual por energía (0.0548 en valor absoluto eran suficientes para reducir mucho la probabilidad de déficit mensual y retornarla a niveles normales. Más aún, si se soslaya el efecto de los mayores precios en el consumo, el costo marginal se sobreestima en 32% y el costo de operación esperado en 41 por ciento.

A feasibility study on age-related factors of wrist pulse using principal component analysis.

Science.gov (United States)

Jang-Han Bae; Young Ju Jeon; Sanghun Lee; Jaeuk U Kim

2016-08-01

Various analysis methods for examining wrist pulse characteristics are needed for accurate pulse diagnosis. In this feasibility study, principal component analysis (PCA) was performed to observe age-related factors of wrist pulse from various analysis parameters. Forty subjects in the age group of 20s and 40s were participated, and their wrist pulse signal and respiration signal were acquired with the pulse tonometric device. After pre-processing of the signals, twenty analysis parameters which have been regarded as values reflecting pulse characteristics were calculated and PCA was performed. As a results, we could reduce complex parameters to lower dimension and age-related factors of wrist pulse were observed by combining-new analysis parameter derived from PCA. These results demonstrate that PCA can be useful tool for analyzing wrist pulse signal.

Spectroscopic Investigation of the Argon Metastable State Through Optical Emission From Pulsed Argon Discharge

Science.gov (United States)

2010-07-01

supply to energize the discharge was connected in series with an ohmite L225J high power 150 Ω resistor and the hollow electrode anode. A stainless...input analog voltage signal to control a piezo -electric actuator within the diode laser head. The general beam path of the diode laser involved an initial

Arcing and rf signal generation during target irradiation by a high-energy, pulsed neutral particle beam

International Nuclear Information System (INIS)

Robiscoe, R.T.

1988-02-01

We present a theory describing the dynamics of arc discharges in bulk dielectric materials on board space-based vehicles. Such ''punch-through'' arcs can occur in target satellites irradiated by high-energy (250 MeV), pulsed (100 mA x 10 ms) neutral particle beams. We treat the arc as a capacitively limited avalanche current in the target dielectric material, and we find expressions for the arc duration, charge transport, currents, and discharge energy. These quantities are adjusted to be consistent with known scaling laws for the area of charge depleted by the arc. After a brief account of the statistical distribution of voltages at which the arc starts and stops, we calculate the signal strength and frequency spectrum of the electromagnetic radiation broadcast by the arc. We find that arcs from thick (/similar to/1 cm) targets can generate rf signals detectable up to 1000 km from the target, bu a radio receiver operating at frequency 80 MHz, bandwidth 100 kHz, and detection threshold -105 dBm. These thick-target arc signals are 10 to 20 dB above ambient noise at the receiver, and they provide target hit assessment if the signal spectrum can be sampled at several frequencies in the nominal range 30-200 MHz. Thin-target (/similar to/1 mm) arc signals are much weaker, but when they are detecable in conjunction with thick-target signals, target discrimination is possible by comparing the signal frequency spectra. 24 refs., 12 figs

Measurand transient signal suppressor

Science.gov (United States)

Bozeman, Richard J., Jr. (Inventor)

1994-01-01

A transient signal suppressor for use in a controls system which is adapted to respond to a change in a physical parameter whenever it crosses a predetermined threshold value in a selected direction of increasing or decreasing values with respect to the threshold value and is sustained for a selected discrete time interval is presented. The suppressor includes a sensor transducer for sensing the physical parameter and generating an electrical input signal whenever the sensed physical parameter crosses the threshold level in the selected direction. A manually operated switch is provided for adapting the suppressor to produce an output drive signal whenever the physical parameter crosses the threshold value in the selected direction of increasing or decreasing values. A time delay circuit is selectively adjustable for suppressing the transducer input signal for a preselected one of a plurality of available discrete suppression time and producing an output signal only if the input signal is sustained for a time greater than the selected suppression time. An electronic gate is coupled to receive the transducer input signal and the timer output signal and produce an output drive signal for energizing a control relay whenever the transducer input is a non-transient signal which is sustained beyond the selected time interval.

Pulse-width discriminators

International Nuclear Information System (INIS)

Budyashov, Yu.G.; Grebenyuk, V.M.; Zinov, V.G.

1978-01-01

A pulse duration discriminator is described which is intended for processing signals from multilayer scintillators. The basic elements of the scintillator are: an input gate, a current generator, an integrating capacitor, a Schmidt trigger and an anticoincidence circuit. The basic circuit of the discriminator and its time diagrams explaining its operating are given. The discriminator is based on microcircuits. Pulse duration discrimination threshold changes continuously from 20 to 100 ns, while its amplitude threshold changes within 20 to 100 mV. The temperature instability of discrimination thresholds (both in pulse width and in amplitude) is better than 0.1 per cent/deg C

Pulse-dose radiofrequency treatment in pain management-initial experience.

Science.gov (United States)

Ojango, Christine; Raguso, Mario; Fiori, Roberto; Masala, Salvatore

2018-05-01

Radiofrequency procedures have been used for treating various chronic pain conditions for decades. These minimally invasive percutaneous treatments employ an alternating electrical current with oscillating radiofrequency wavelengths to eliminate or alter pain signals from the targeted site. The aim of the continuous radiofrequency procedure is to increase the temperature sufficiently to create an irreversible thermal lesion on nerve fibres and thus permanently interrupt pain signals. The pulsed radiofrequency procedure utilises short pulses of radiofrequency current with intervals of longer pauses to avert a temperature increase to the level of permanent tissue damage. The goal of these pulses is to alter the processing of pain signals, but to avoid relevant structural damage to nerve fibres, as seen in the continuous radiofrequency procedure. The pulse-dose radiofrequency procedure is a technical improvement of the pulsed radiofrequency technique in which the delivery mode of the current is adapted. During the pulse-dose radiofrequency procedure thermal damage is avoided. In addition, the amplitude and width of the consecutive pulses are kept the same. The method ensures that each delivered pulse keeps the same characteristics and therefore the dose is similar between patients. The current review outlines the pulse-dose radiofrequency procedure and presents our institution's chronic pain management studies.

125-GHz Microwave Signal Generation Employing an Integrated Pulse Shaper

DEFF Research Database (Denmark)

Liao, Shasha; Ding, Yunhong; Dong, Jianji

2017-01-01

We propose and experimentally demonstrate an on-chip pulse shaper for 125-GHz microwave waveform generation. The pulse shaper is implemented based on a silicon-on-insulator (SOI) platform that has a structure with eight-tap finite impulse response (FIR) and there is an amplitude modulator on each...... of the generated microwave waveforms is larger than 100 GHz, and it has wide bandwidth when changing the time delay of the adjacent taps and compactness, capability for integration with electronics and small power consumption are also its merits.......We propose and experimentally demonstrate an on-chip pulse shaper for 125-GHz microwave waveform generation. The pulse shaper is implemented based on a silicon-on-insulator (SOI) platform that has a structure with eight-tap finite impulse response (FIR) and there is an amplitude modulator on each...

Análisis de alternativas tecnológicas y energéticas para el sistema metroplús bajo una evaluación integrada energía, ambiente, economía

OpenAIRE

Alzate, Juan M; Builes, Luis A; Rave, Claudia C.; Smith, Ricardo A.; Cadena, Ángela I.

2008-01-01

Con un modelo de optimización multi­periodo, basado en programación lineal, y de tipo integrado Energía­Ambiente­Economía (MARKAL­Estándar), se estimaron impactos económicos, energéticos y ambientales de cinco alternativas tecnológicas para la flota de buses que atenderá la demanda de movilidad del sistema de transporte masivo de pasajeros, de mediana capacidad, del Área Metropolitana del Valle de Aburrá (Medellín – Colombia) ­Sistema Metroplús­. Las alternativa...

Receiver Architecture for 12.5 Gb/s 16-ary Pulse Position Modulation (PPM) Signaling

Energy Technology Data Exchange (ETDEWEB)

Mendez, A J; Gagliardi, R M; Hernandez, V J; Bennett, C V

2008-07-11

PPM is a signaling scheme that enables the transmission of multiple bits per symbol [1]. It has found favor in the regime of free space optical communications ('FSO' or 'Lasercom'); however, PPM has yet to be widely applied to fiber optic-based communications. Its limitation in fiber results from the exceedingly high bandwidth requirements needed to electronically process a directly detected pulse, especially as the symbol rate increases and the pulse width correspondingly decreases. As a solution, we introduced the concept of a virtual quadrant receiver for receiving 1.25 Gb/s 4-ary PPM, where photonic processing reduced the number of required electronic components [2]. In this paper, we extend these photonic process techniques to a 16-ary, 12.5 Gb/s (10 Gb/s plus 8B/10B line coding) PPM communications system for fiber optic avionics, wherein much of the receiver processing is enabled by techniques based on planar lightwave circuits (PLCs). The architecture is applicable to higher input data rates and M-ary PPM. In the following, we present the PPM encoding and decoding architectures and numerically simulated results.

Pulsed neutron generator for mass flow measurement using the pulsed neutron activation technique

International Nuclear Information System (INIS)

Rochau, G.E.; Hornsby, D.R.; Mareda, J.F.; Riggan, W.C.

1980-01-01

A high-output, transportable neutron generator has been developed to measure mass flow velocities in reactor safety tests using the Pulsed Neutron Activation (PNA) Technique. The PNA generator produces >10 10 14 MeV D-T neutrons in a 1.2 millisecond pulse. The Millisecond Pulse (MSP) Neutron Tube, developed for this application, has an expected operational life of 1000 pulses, and it limits the generator pulse repetition rate to 12 pulses/minute. A semiconductor neutron detector is included in the generator package to monitor the neutron output. The control unit, which can be operated manually or remotely, also contains a digital display with a BCD output for the neutron monitor information. The digital logic of the unit controls the safety interlocks and rejects transient signals which could accidently fire the generator

Avaliação do desempenho energético de um grande edifício de serviços existente

OpenAIRE

Garrido, Diogo Emanuel da Silva

2013-01-01

Nesta dissertação pretende-se caracterizar o desempenho energético de um grande edifício de serviços existente, da tipologia ensino, avaliar e identificar potenciais medidas que melhorem aquele desempenho, permitindo, em complemento, determinar a sua classificação energética no âmbito da legislação vigente. A pertinência do estudo prende-se com a avaliação do desempenho energético dos edifícios e com o estudo de medidas de melhoria que permitam incrementar a eficiência energéti...

Polymeric electrochemical element for adaptive networks: Pulse mode

International Nuclear Information System (INIS)

Smerieri, Anteo; Berzina, Tatiana; Erokhin, Victor; Fontana, M. P.

2008-01-01

An electrochemically controlled polymeric heterojunction working as a memristor, i.e., having memory properties, was investigated in pulse mode, mimicking synaptic behavior of signal transmission in biological systems. Influence of parameters such as pulse duration, interval between pulses, and value of potential base level was analyzed. Learning capabilities were shown to be reversible and repeatable for both potentiation and inhibition of signal transmission. The adaptive behavior of the element was investigated and was shown to be more efficient than the dc mode

Double pulse laser ablation and plasma: Laser induced breakdown spectroscopy signal enhancement

International Nuclear Information System (INIS)

Babushok, V.I.; DeLucia, F.C.; Gottfried, J.L.; Munson, C.A.; Miziolek, A.W.

2006-01-01

A review of recent results of the studies of double laser pulse plasma and ablation for laser induced breakdown spectroscopy applications is presented. The double pulse laser induced breakdown spectroscopy configuration was suggested with the aim of overcoming the sensitivity shortcomings of the conventional single pulse laser induced breakdown spectroscopy technique. Several configurations have been suggested for the realization of the double pulse laser induced breakdown spectroscopy technique: collinear, orthogonal pre-spark, orthogonal pre-heating and dual pulse crossed beam modes. In addition, combinations of laser pulses with different wavelengths, different energies and durations were studied, thus providing flexibility in the choice of wavelength, pulse width, energy and pulse sequence. The double pulse laser induced breakdown spectroscopy approach provides a significant enhancement in the intensity of laser induced breakdown spectroscopy emission lines up to two orders of magnitude greater than a conventional single pulse laser induced breakdown spectroscopy. The double pulse technique leads to a better coupling of the laser beam with the plasma plume and target material, thus providing a more temporally effective energy delivery to the plasma and target. The experimental results demonstrate that the maximum effect is obtained at some optimum separation delay time between pulses. The optimum value of the interpulse delay depends on several factors, such as the target material, the energy level of excited states responsible for the emission, and the type of enhancement process considered. Depending on the specified parameter, the enhancement effects were observed on different time scales ranging from the picosecond time level (e.g., ion yield, ablation mass) up to the hundred microsecond level (e.g., increased emission intensity for laser induced breakdown spectroscopy of submerged metal target in water). Several suggestions have been proposed to explain

Method for integrating a train of fast, nanosecond wide pulses

International Nuclear Information System (INIS)

Rose, C.R.

1987-01-01

This paper describes a method used to integrate a train of fast, nanosecond wide pulses. The pulses come from current transformers in a RF LINAC beamline. Because they are ac signals and have no dc component, true mathematical integration would yield zero over the pulse train period or an equally erroneous value because of a dc baseline shift. The circuit used to integrate the pulse train first stretches the pulses to 35 ns FWHM. The signals are then fed into a high-speed, precision rectifier which restores a true dc baseline for the following stage - a fast, gated integrator. The rectifier is linear over 55dB in excess of 25 MHz, and the gated integrator is linear over a 60 dB range with input pulse widths as short as 16 ns. The assembled system is linear over 30 dB with a 6 MHz input signal

Gas ultrasonic flow rate measurement through genetic-ant colony optimization based on the ultrasonic pulse received signal model

Science.gov (United States)

Hou, Huirang; Zheng, Dandan; Nie, Laixiao

2015-04-01

For gas ultrasonic flowmeters, the signals received by ultrasonic sensors are susceptible to noise interference. If signals are mingled with noise, a large error in flow measurement can be caused by triggering mistakenly using the traditional double-threshold method. To solve this problem, genetic-ant colony optimization (GACO) based on the ultrasonic pulse received signal model is proposed. Furthermore, in consideration of the real-time performance of the flow measurement system, the improvement of processing only the first three cycles of the received signals rather than the whole signal is proposed. Simulation results show that the GACO algorithm has the best estimation accuracy and ant-noise ability compared with the genetic algorithm, ant colony optimization, double-threshold and enveloped zero-crossing. Local convergence doesn’t appear with the GACO algorithm until -10 dB. For the GACO algorithm, the converging accuracy and converging speed and the amount of computation are further improved when using the first three cycles (called GACO-3cycles). Experimental results involving actual received signals show that the accuracy of single-gas ultrasonic flow rate measurement can reach 0.5% with GACO-3 cycles, which is better than with the double-threshold method.

Performance review of an indigenously developed high power test stand built for the Indian S-band 5 MW pulsed klystron development

International Nuclear Information System (INIS)

Shrivastava, Purushottam; Baxy, D.; Mulchandani, J.; Hannurkar, P.R.; Joshi, L.M.

2003-01-01

CAT took up development of 5 MW S-Band klystrons indigenously in collaboration with CEERI Pilani. The development of klystron prototype is completed. These klystrons are very crucial devices, for energizing the 10-20 MeV electron accelerators, which are developed in the country for various industrial, medical and scientific applications. A test station has been developed indigenously at CAT for these klystrons. It consists of a 12 MW peak power 130 kV klystron pulse modulator, a 1 : 10 pulse transformer, 130 kV high voltage deck having high voltage pulse divider, pulse current transformer as well indigenously built klystron socket, filament supplies, klystron support structure and pulse transformer oil tank. After development/rigorous testing the test stand was shifted to CEERI and was installed and commissioned there by CAT. Gun collector test module and prototypes of the 5 MW klystron were tested, aged and conditioned at high power using this test stand. The details of the system / test results are discussed

Ultrashort pulse shaping by optical parametric chirped amplification

International Nuclear Information System (INIS)

Nelet, Ambre

2007-01-01

The aim of this work is to propose new laser architectures based on optical parametric chirped pulse amplification (OPCPA). Common goals of OPCPA pre-amplifiers are to reach high energy level while maintaining the spectrum width and to adapt geometry of the amplified beam to the high power laser chain optics. We consider OPCPA as a way to control and to sculpt ultrashort pulses. Our first set-up aims at thwarting possible time recovery default between pump and signal pulses, which lower the energy extraction. A regenerative OPCPA, idler resonant, is a way to produce a high-intensity and high-repetition rate train of amplified signal replicas. Our second laser system pre-compensates the spectral gain narrowing by sculpting pulses directly within the OPCPA section, where a temporal shaping of the pump beam permits a spectro-spectral shaping of the amplified signal. Finally, we propose an OPCPA based on spatial coding and uniform amplification of spectral signal components by using a fan-out periodically poled crystal and a zero dispersion line. (author) [fr

Las energías renovables como oportunidad y desafío para el desarrollo territorial (Valle de Lerma, Salta – Argentina

Directory of Open Access Journals (Sweden)

Silvina Belmonte

2014-03-01

Full Text Available La evaluación de Energías Renovables se plantea en un contexto de Ordenamiento Territorial del Valle de Lerma (Salta como estrategia para el desarrollo regional y mejora de la calidad de vida y del ambiente. Herramientas de Evaluación Multi-Criterio, aplicaciones de Sistemas de Información Geográfica y técnicas participativas de consulta constituyen el sustento metodológico del trabajo. Los resultados se focalizan en tres puntos: diagnóstico territorial, evaluación del recurso energético y alternativas tecnológicas, y propuestas para la planificación y gestión. En el diagnóstico, las energías renovables fueron identificadas como opciones viables particularmente en cuestiones productivas y de acceso a servicios básicos. La potencialidad de los recursos renovables resultó alta en relación a la radiación solar y recurso hidráulico, moderado para el potencial eólico y de alta diversidad para el tema de biomasa. Entre las medidas de eficiencia y tecnologías evaluadas, surgieron como prioritarias: educación ambiental, planificación energética estratégica y variadas aplicaciones de energía solar (secaderos, invernaderos, arquitectura bioclimática, colectores de agua y cocinas. Entre las orientaciones para el desarrollo de políticas energéticas ‘más’ sustentables se destacaron: coordinación del sector energético con otros sectores y niveles de actuación en el marco de una planificación territorial integral, fortalecimiento de instituciones locales para la gestión energética, y superación de barreras – limitaciones a la transferencia de energías renovables y medidas de eficiencia energética a nivel local. Finalmente, en las conclusiones se plantea la importancia de valorar las energías renovables como oportunidad y desafío para promover procesos de ‘cambio’ en la región, en una concepción más comprometida con el ambiente y la sociedad.

Improved background suppression in 1H MAS NMR using composite pulses

Science.gov (United States)

Odedra, Smita; Wimperis, Stephen

2012-08-01

A well known feature of 1H MAS NMR spectroscopy, particularly of solids where the concentration of 1H nuclei is low, is the presence in the spectrum of a significant broad "background" signal arising from 1H nuclei that are outside the MAS rotor and radiofrequency coil, probably located on the surfaces of the static components of the probehead. A popular method of suppressing this unwanted signal is the "depth pulse" method, consisting of a 90° pulse followed by one or two 180° pulses that are phase cycled according to the "Exorcycle" scheme, which removes signal associated with imperfect 180° pulses. Consequently, only spins in the centre of the radiofrequency coil contribute to the 1H MAS spectrum, while those experiencing a low B1 field outside the coil are suppressed. Although very effective at removing background signal from the spectrum, one drawback with this approach is that significant loss of the desired signal from the sample also occurs. Here we investigate the 1H background suppression problem and, in particular, the use of novel antisymmetric passband composite pulses to replace the simple pulses in a depth pulse experiment. We show that it is possible to improve the intensity of the 1H signals of interest while still maintaining effective background suppression. We expect that these results will be relevant to 1H MAS NMR studies of, for example, nominally perdeuterated biological samples or nominally anhydrous inorganic materials.

Participación de la energía hidroeléctrica en México para el 2013

OpenAIRE

Loredo González, Jesús Alberto; Mendoza Ramírez, Virginia; Salgado Banda, Karla María; Segovia Salazar, Perla; Vargas de la Rosa, Laura Nohemí; Zamudio Morán, Roberto Abraham; Martínez, Ubaldo

2013-01-01

El estudio de energías alternas es importante pues, en la actualidad, se busca reducir el alto consumo de fuentes energéticas de tipo fósil con el fin de controlar el impacto ambiental ocasionado por la generación de esta. la energía hidroeléctrica es un área de oportunidad que México debe aprovechar, esta depende de la meteorología de cada región así como de los meses con mayor precipitación pluvial. la producción de electricidad por medios hídricos ha presentado una tendencia crecie...

Magnetic pulse sharpener and delay-line

International Nuclear Information System (INIS)

Li Jin; Dai Guangsen; Xia Liansheng

2002-01-01

This paper describes a method to achieve short rise time pulse which has been delayed with a delay-line and magnetic pulse sharpener. A delay-line and two shock-lines are designed to carry pulsed signal with a maximum voltage magnitude up to 80 kV. A pulse of High voltage with arise time of 48 ns at a level of 0.1%-0.9% were achieved, and the attenuation in the line is very small

Estudio comparativo de eficiencia energética: Fachada ventilada frente a fachada vegetal

OpenAIRE

Azkorra Larrinaga, Zaloa

2015-01-01

398 p. + anexos En la actualidad se desarrollan multitud de investigaciones relacionadas con la rehabilitación energética lo que la ha convertido en un campo emergente en el sector de la construcción y de la arquitectura.El objetivo general de la tesis es evaluar la aplicabilidad de diferentes sistemas pasivos de rehabilitación de fachadas (fachada ventilada y fachada vegetal) y analizar los beneficios de la incorporación de dichos sistemas en el ahorro energético de edificios.Para ello, s...

Análisis armónico de compensadores de energía reactiva

OpenAIRE

González Hernández, Jaime

2011-01-01

Desde la implantación de la generación y distribución de la energía eléctrica en corriente alterna, la energía reactiva ha sido un factor clave en el diseño y explotación de los consumos y redes eléctricas. El carácter reactivo (inductivo) que presentan, en general, los consumos y los elementos de las redes eléctricas han hecho aparecer a lo largo del tiempo distintos dispositivos y técnicas que buscan "compensar" ese carácter reactivo.

Photoplethysmogram signal quality estimation using repeated Gaussian filters and cross-correlation

International Nuclear Information System (INIS)

Karlen, W; Kobayashi, K; Dumont, G A; Ansermino, J M

2012-01-01

Pulse oximeters are monitors that noninvasively measure heart rate and blood oxygen saturation (SpO 2 ). Unfortunately, pulse oximetry is prone to artifacts which negatively impact the accuracy of the measurement and can cause a significant number of false alarms. We have developed an algorithm to segment pulse oximetry signals into pulses and estimate the signal quality in real time. The algorithm iteratively calculates a signal quality index (SQI) ranging from 0 to 100. In the presence of artifacts and irregular signal morphology, the algorithm outputs a low SQI number. The pulse segmentation algorithm uses the derivative of the signal to find pulse slopes and an adaptive set of repeated Gaussian filters to select the correct slopes. Cross-correlation of consecutive pulse segments is used to estimate signal quality. Experimental results using two different benchmark data sets showed a good pulse detection rate with a sensitivity of 96.21% and a positive predictive value of 99.22%, which was equivalent to the available reference algorithm. The novel SQI algorithm was effective and produced significantly lower SQI values in the presence of artifacts compared to SQI values during clean signals. The SQI algorithm may help to guide untrained pulse oximeter users and also help in the design of advanced algorithms for generating smart alarms. (paper)

Photoplethysmogram signal quality estimation using repeated Gaussian filters and cross-correlation.

Science.gov (United States)

Karlen, W; Kobayashi, K; Ansermino, J M; Dumont, G A

2012-10-01

Pulse oximeters are monitors that noninvasively measure heart rate and blood oxygen saturation (SpO2). Unfortunately, pulse oximetry is prone to artifacts which negatively impact the accuracy of the measurement and can cause a significant number of false alarms. We have developed an algorithm to segment pulse oximetry signals into pulses and estimate the signal quality in real time. The algorithm iteratively calculates a signal quality index (SQI) ranging from 0 to 100. In the presence of artifacts and irregular signal morphology, the algorithm outputs a low SQI number. The pulse segmentation algorithm uses the derivative of the signal to find pulse slopes and an adaptive set of repeated Gaussian filters to select the correct slopes. Cross-correlation of consecutive pulse segments is used to estimate signal quality. Experimental results using two different benchmark data sets showed a good pulse detection rate with a sensitivity of 96.21% and a positive predictive value of 99.22%, which was equivalent to the available reference algorithm. The novel SQI algorithm was effective and produced significantly lower SQI values in the presence of artifacts compared to SQI values during clean signals. The SQI algorithm may help to guide untrained pulse oximeter users and also help in the design of advanced algorithms for generating smart alarms.

Optimal Linear Filters for Pulse Height Measurements in the Presence of Noise

International Nuclear Information System (INIS)

Nygaard, K.

1966-07-01

For measurements of nuclear pulse height spectra a linear filter is used between the pulse amplifier and the pulse height recorder so as to improve the signal/noise ratio. The problem of finding the optimal filter is investigated with emphasis on technical realizability. The maximum available signal/noise ratio is theoretically calculated on the basis of all the information which can be found in the output of the pulse amplifier, and on an assumed a priori knowledge of the pulse time of arrival. It is then shown that the maximum available signal/noise ratio can be obtained with practical measurements without any a priori knowledge of pulse time of arrival, and a general description of the optimal linear filter is given. The solution is unique, technically realizable, and based solely on data (noise power spectrum and pulse shape) which can be measured at the output terminals of the pulse amplifier used

Optimal Linear Filters for Pulse Height Measurements in the Presence of Noise

Energy Technology Data Exchange (ETDEWEB)

Nygaard, K

1966-07-15

For measurements of nuclear pulse height spectra a linear filter is used between the pulse amplifier and the pulse height recorder so as to improve the signal/noise ratio. The problem of finding the optimal filter is investigated with emphasis on technical realizability. The maximum available signal/noise ratio is theoretically calculated on the basis of all the information which can be found in the output of the pulse amplifier, and on an assumed a priori knowledge of the pulse time of arrival. It is then shown that the maximum available signal/noise ratio can be obtained with practical measurements without any a priori knowledge of pulse time of arrival, and a general description of the optimal linear filter is given. The solution is unique, technically realizable, and based solely on data (noise power spectrum and pulse shape) which can be measured at the output terminals of the pulse amplifier used.

Investigación e impacto ambiental de los edificios. La energía

Directory of Open Access Journals (Sweden)

Rodríguez Aumente, Pedro A.

2005-08-01

Full Text Available This conference describes the main problems of energy use in face of the depleting of fosil resources, energy supply and emission of atmospheric toxic gases, green house effect gases and ozone depleting gases. The relevance of energy consumption in the environment impact is commented, as well as the key points for the posible evolution of the problem and in the appropriate technology research to cope with them In order to improve the energy and ecological efficiency of buidings. The main characteristics of present day technologies for the introduction of renewable energies in buidings are comented, dealing with their barriers for the widespread use. The most recent research on air conditioning using thermal solar energy with absorption machines is described, with application to Madrid.Se presenta la problemática actual del uso de la energía de cara al agotamiento de las fuentes fósiles, el abastecimiento y la contaminación atmosférica de gases tóxicos, de efecto invernadero y destructores de la capa de ozono. Se comenta la relevancia de la energía en el impacto ambiental de los edificios y se discuten los distintos aspectos que inciden en la posible evolución futura del problema y en la mejor estrategia de investigación tecnológica para tratar de mejorar la eficiencia energética y medioambiental de los edificios, especialmente en España. Se presentan las tecnologías actuales de introducción de las energías renovables en los edificios y se comentan sus más relevantes características, haciendo hincapié en las barreras para su difusión. Se describe la actividad más reciente de investigación en la climatización por energía solar haciendo uso de máquina de absorción, con aplicación a Madrid.

Organización Institucional en el Sector Energético en el Uruguay y participantes en el mismo

Directory of Open Access Journals (Sweden)

José A. Alem Deaces

2014-02-01

Full Text Available La energía , su probable falta o escasez, precio y su importancia en la satisfacción de necesidades mínimas humanas,  en el desarrollo y crecimiento de los países mediante la producción, aunque siempre ha sido un tema en estudio, ha cobrado en la actualidad mayor relieve.Ningún país es pasivo ante ello y adecuan su organización a fin de satisfacer sus necesidades y con ella las de sus poblaciones.Hemos asistido  a un proceso de creación de nuevas personas públicas y privadas que se sumaron a las ya existentes, para participar en el ciclo energético.Este proceso cobró impulso en los tres últimos lustros.El Estado, ha tomado decisiones, sea favoreciendo la apertura del mercado energético, sea buscando viabilizar conexiones internacionales, que han llevado a cambios en el sector institucional referido a la energía.Se ha avanzado a tal punto, que ya podríamos hablar de un “Derecho de la Energía”, lo que será objeto de discusión en su momento, con este trabajo pretendo iniciar el estudio y discusión profundo desde el punto de vista jurídico de un tema, que ha cumplido la mayoría de edad.La determinación de las personas que intervienen el ciclo energético, es un importante primer paso.

Pulsed Corona Discharge Generated By Marx Generator

Science.gov (United States)

Sretenovic, G. B.; Obradovic, B. M.; Kovacevic, V. V.; Kuraica, M. M.; Puric J.

2010-07-01

The pulsed plasma has a significant role in new environmental protection technologies. As a part of a pulsed corona system for pollution control applications, Marx type repetitive pulse generator was constructed and tested in arrangement with wire-plate corona reactor. We performed electrical measurements, and obtained voltage and current signals, and also power and energy delivered per pulse. Ozone formation by streamer plasma in air was chosen to monitor chemical activity of the pulsed corona discharge.

Synthesizing genetic sequential logic circuit with clock pulse generator.

Science.gov (United States)

Chuang, Chia-Hua; Lin, Chun-Liang

2014-05-28

Rhythmic clock widely occurs in biological systems which controls several aspects of cell physiology. For the different cell types, it is supplied with various rhythmic frequencies. How to synthesize a specific clock signal is a preliminary but a necessary step to further development of a biological computer in the future. This paper presents a genetic sequential logic circuit with a clock pulse generator based on a synthesized genetic oscillator, which generates a consecutive clock signal whose frequency is an inverse integer multiple to that of the genetic oscillator. An analogous electronic waveform-shaping circuit is constructed by a series of genetic buffers to shape logic high/low levels of an oscillation input in a basic sinusoidal cycle and generate a pulse-width-modulated (PWM) output with various duty cycles. By controlling the threshold level of the genetic buffer, a genetic clock pulse signal with its frequency consistent to the genetic oscillator is synthesized. A synchronous genetic counter circuit based on the topology of the digital sequential logic circuit is triggered by the clock pulse to synthesize the clock signal with an inverse multiple frequency to the genetic oscillator. The function acts like a frequency divider in electronic circuits which plays a key role in the sequential logic circuit with specific operational frequency. A cascaded genetic logic circuit generating clock pulse signals is proposed. Based on analogous implement of digital sequential logic circuits, genetic sequential logic circuits can be constructed by the proposed approach to generate various clock signals from an oscillation signal.

Programación por metas Energía alternativa mediante biomasa.

Directory of Open Access Journals (Sweden)

Guerrero Casas, Flor María

2003-01-01

Full Text Available En este trabajo se presenta un modelo multicriterio de localización de centrales de generación de energía eléctrica mediante biomasa. Los objetivos considerados son: (1 minimizar el coste total de la operación, (2 maximizar la producción de electricidad obtenida, (3 maximizar la distancia entre plantas, (4 maximizar la aceptación social y (5 establecer las plantas o ampliaciones en aquellos lugares donde exista una mayor predisposición por parte de las administraciones locales. Finalmente, se concluye con una aplicación práctica mediante programación por metas ponderadas para la región andaluza, considerando los residuos procedentes del olivar como fuente de energía.

Consideraciones para la adopción de energía nucleoeléctrica a la matriz energética del Ecuador e interconexión a Colombia y Perú

OpenAIRE

Amancha Proaño, Pablo Israel

2014-01-01

El consumo mundial de energía eléctrica ha tenido un considerable crecimiento, con mayor penetración de tecnologías fósiles, aumentando las concentraciones globales de CO2 y CH4, que exceden valores medios de los últimos milenios, lo cual provocará problemas en el clima global. Urge adoptar tecnologías sustentables en diferentes países y sectores. Ecuador, Perú y Colombia, con tasas similares de crecimiento en lo económico y energético, han visto en la hidroenergía su principal fuente de gene...

Research for robust femtosecond chirped-pulse amplification laser with an identical positive dispersive media as pulse stretcher and compressor

International Nuclear Information System (INIS)

Akahane, Yutaka; Ogawa, Kanade; Tsuji, Koichi; Aoyama, Makoto; Yamakawa, Koichi

2011-01-01

We have proposed and demonstrated a simple and robust femtosecond optical-parametric chirped-pulse amplification scheme in which an even order dispersion of an idler pulse is compensated by passing through an identical positive dispersive material used for temporal stretching a signal pulse. By compressing the idler pulses having a negatively chirp in this manner, high power sub-100 fs pulses were successfully obtained with only a transparent glass block used for the stretcher and compressor. (author)

Type 2 diabetes screening test by means of a pulse oximeter

OpenAIRE

Monte Moreno, Enrique; Anyo Luján, María José; Torres Rusiñol, Montse; Juarez Fernández, Paqui; Núñez Manrique, Pilar; Aragón Triviño, Cristina; Pedrosa Miquel, Magda; Álvarez-Rodríguez, Marife; González-Burguillos, María José

2016-01-01

In this paper, we propose a method for screening for the presence of type 2 diabetes by means of the signal obtained from a pulse oximeter. The screening system consists of two parts; the first analyses the signal obtained from the pulse oximeter, and the second consists of a machine-learning module. The system consists of a front end that extracts a set of features form the pulse oximeter signal. These features are based on physiological considerations. The set of featur...

Active cancellation - A means to zero dead-time pulse EPR.

Science.gov (United States)

Franck, John M; Barnes, Ryan P; Keller, Timothy J; Kaufmann, Thomas; Han, Songi

2015-12-01

The necessary resonator employed in pulse electron paramagnetic resonance (EPR) rings after the excitation pulse and creates a finite detector dead-time that ultimately prevents the detection of signal from fast relaxing spin systems, hindering the application of pulse EPR to room temperature measurements of interesting chemical or biological systems. We employ a recently available high bandwidth arbitrary waveform generator (AWG) to produce a cancellation pulse that precisely destructively interferes with the resonant cavity ring-down. We find that we can faithfully detect EPR signal at all times immediately after, as well as during, the excitation pulse. This is a proof of concept study showcasing the capability of AWG pulses to precisely cancel out the resonator ring-down, and allow for the detection of EPR signal during the pulse itself, as well as the dead-time of the resonator. However, the applicability of this approach to conventional EPR experiments is not immediate, as it hinges on either (1) the availability of low-noise microwave sources and amplifiers to produce the necessary power for pulse EPR experiment or (2) the availability of very high conversion factor micro coil resonators that allow for pulse EPR experiments at modest microwave power. Copyright © 2015 Elsevier Inc. All rights reserved.

Effects of laser wavelengths and pulse energy ratio on the emission enhancement in dual pulse LIBS

International Nuclear Information System (INIS)

Ahmed, Rizwan; Iqbal, Javed; Baig, M Aslam

2015-01-01

We present new studies on the effects of laser wavelengths, pulse energy ratio and interpulse delay between two laser pulses in the collinear dual pulse configuration of laser-induced breakdown spectroscopy (LIBS) on an iron sample in air using the fundamental (1064 nm) and the second harmonics (532 nm) of Nd:YAG lasers. In the dual pulse LIBS, an optimum value of interpulse delay with an appropriate combination of laser wavelengths, and laser pulse energy ratio, yields a 30 times signal intensity enhancement in the neutral iron lines as compared with single pulse LIBS. A comparison in the spatial variations of electron temperature along the axis of the plume expansion in single and double pulse LIBS has also been studied. (letter)

Pulse-Width-Modulating Driver for Brushless dc Motor

Science.gov (United States)

Salomon, Phil M.

1991-01-01

High-current pulse-width-modulating driver for brushless dc motor features optical coupling of timing signals from low-current control circuitry to high-current motor-driving circuitry. Provides high electrical isolation of motor-power supply, helping to prevent fast, high-current motor-driving pulses from being coupled through power supplies into control circuitry, where they interfere with low-current control signals.

Improved background suppression in ¹H MAS NMR using composite pulses.

Science.gov (United States)

Odedra, Smita; Wimperis, Stephen

2012-08-01

A well known feature of ¹H MAS NMR spectroscopy, particularly of solids where the concentration of ¹H nuclei is low, is the presence in the spectrum of a significant broad "background" signal arising from ¹H nuclei that are outside the MAS rotor and radiofrequency coil, probably located on the surfaces of the static components of the probehead. A popular method of suppressing this unwanted signal is the "depth pulse" method, consisting of a 90° pulse followed by one or two 180° pulses that are phase cycled according to the "Exorcycle" scheme, which removes signal associated with imperfect 180° pulses. Consequently, only spins in the centre of the radiofrequency coil contribute to the ¹H MAS spectrum, while those experiencing a low B₁ field outside the coil are suppressed. Although very effective at removing background signal from the spectrum, one drawback with this approach is that significant loss of the desired signal from the sample also occurs. Here we investigate the ¹H background suppression problem and, in particular, the use of novel antisymmetric passband composite pulses to replace the simple pulses in a depth pulse experiment. We show that it is possible to improve the intensity of the ¹H signals of interest while still maintaining effective background suppression. We expect that these results will be relevant to ¹H MAS NMR studies of, for example, nominally perdeuterated biological samples or nominally anhydrous inorganic materials. Copyright © 2012 Elsevier Inc. All rights reserved.

Dynamic characterization and amplification of sub-picosecond pulses in fiber optical parametric chirped pulse amplifiers

DEFF Research Database (Denmark)

Cristofori, Valentina; Lali-Dastjerdi, Zohreh; Rishøj, Lars Søgaard

2013-01-01

We show a first-time demonstration of amplification of 400 fs pulses in a fiber optical parametric amplifier. The 400 fs signal is stretched in time, amplified by 26 dB and compressed back to 500 fs. A significant broadening of the pulses is experimentally shown due to dispersion and limited gain...

Física y química: 1 Bachillerato. Calor y principio de conservación de la energía

OpenAIRE

Carrascosa Alís, Jaime; Martínez Sala, Salvador; Martínez-Torregrosa, Joaquín

1998-01-01

Cuando la energía mecánica disminuye, los objetos se calientan. ¿Hay alguna relación entre los cambios en propiedades mecánicas y térmicas?. La termología (con su hipótesis del "calórico") y sus límites con la mecánica: ¿cómo explicar que aumente la temperatura de todos los cuerpos cuando hay rozamiento?. Los trabajos de Joule. Generalización de la conservación de la energía. ¿Si la energía siempre se conserva en un sistema aislado, por qué hablamos de "crisis energética"?. Análisis de las ca...

Local eddy current measurements in pulsed fields

Energy Technology Data Exchange (ETDEWEB)

Espina-Hernandez, J.H. [SEPI-Electronica, ESIME-IPN, UPALM Edif. ' Z' . Zacatenco, Mexico DF 07738 (Mexico)], E-mail: jhespina@gmail.com; Groessinger, R. [Institute of Solid State Physics, Vienna University of Technology, Wiedner Hauptstrasse 8-10, A-1040 Vienna (Austria); Hallen, J.M. [Departamento de Ingenieria Metalurgica, IPN-ESIQIE, UPALM Edif. 7, Zacatenco, Mexico DF 07738 (Mexico)

2008-07-15

This work presents new eddy current measurements in pulsed fields. A commercial point pick-up coil is used to detect the induction signal along the radius of Cu and Al samples with cylindrical shape and diameters between 5 and 35 mm. Local eddy current measurements were performed on the surface of conducting materials due to the small dimensions of the coil. A simple electrical circuit, used as a model, is proposed to describe the local eddy current effect in pulsed fields. The proposed model allows to calculate the phase shift angle between the signal proportional to eddy currents and the applied external field in a pulsed field magnetometer.

Methods and Apparatus for Pulsed-DC Dielectric Barrier Discharge Plasma Actuator and Circuit

Science.gov (United States)

Corke, Thomas C. (Inventor); Kaszeta, Richard (Inventor); Gold, Calman (Inventor)

2017-01-01

A plasma generating device intended to induce a flow in a fluid via plasma generation includes a dielectric separating two electrodes and a power supply. The first electrode is exposed to a fluid flow while the second electrode is positioned under the dielectric. The power supply is electrically coupled to a switch and the first and second electrodes. When the power supply is energized by repeated action of the switch, it causes a pulsed DC current between the electrodes which causes the fluid to ionize generating a plasma. The generation of the plasma induces a force with a velocity component in the fluid.

Diagnóstico energético en el proceso de molienda de la laterita

Directory of Open Access Journals (Sweden)

Reynaldo Laborde-Brown

2004-03-01

Full Text Available El consumo específico de energía en el proceso de molienda del mineral laterítico en la empresa Comandante Ernesto Che Guevara de Moa no muestra un comportamiento estable, lo que repercute en el aumento de los costos de producción. Para determinar las causas que originan estas variaciones se realizó una investigación en la unidad de molienda, específicamente en sus dos equipos principales: el molino de bolas y el ventilador de recirculación. Los resultados arrojaron que la variabilidad observada en el consumo energético se debe, fundamentalmente, a la ausencia de estabilidad en el flujo de alimentación de los molinos. Se obtiene un modelo estadístico que permite predecir el comportamiento del consumo específico de energía en función de la productividad diaria de la sección de molienda.

Electrical system for pulse-width modulated control of a power inverter using phase-shifted carrier signals and related operating methods

Science.gov (United States)

Welchko, Brian A [Torrance, CA

2012-02-14

Systems and methods are provided for pulse-width modulated control of power inverter using phase-shifted carrier signals. An electrical system comprises an energy source and a motor. The motor has a first set of windings and a second set of windings, which are electrically isolated from each other. An inverter module is coupled between the energy source and the motor and comprises a first set of phase legs coupled to the first set of windings and a second set of phase legs coupled to the second set of windings. A controller is coupled to the inverter module and is configured to achieve a desired power flow between the energy source and the motor by modulating the first set of phase legs using a first carrier signal and modulating the second set of phase legs using a second carrier signal. The second carrier signal is phase-shifted relative to the first carrier signal.

Efectos de la entropía urbana en el coste energético del trasporte

Directory of Open Access Journals (Sweden)

Francisco Bascuñán Walker

2011-05-01

Full Text Available El objetivo del trabajo presentado fue descubrir los efectos de la diversidad de uso de suelo o entropía urbana sobre el gasto energético del transporte. Se eligió como zona de estudio la ciudad de La Serena y se encuestó a un grupo representativo de familias con gastos energéticos y de estratos sociales diversos y se comparó con las zonas urbanas de diferentes grados de entropía. El estudio mostró que, indistintamente del nivel social, los habitantes de las zonas que mostraban niveles mayores de entropía gastaban menos energía en traslados a destinos urbanos que aquellos que vivían en zonas de menores entropías. Basados en los resultados del estudio se concluyó que para disminuir el gasto energético en trasporte de los habitantes de la ciudad se requería incrementar el nivel de entropía. La alternativa más eficiente estudiada fue contemplar en la planificación urbana, pequeños policentros de multiservicios (más de tres servicios diferentes que cubran una superficie de población urbana de 78 has aproximadamente.

Pulsed hydrogen fluoride laser oscillator-amplifier experiments

International Nuclear Information System (INIS)

Schott, G.L.

1975-01-01

Pulsed HF chemical laser oscillator energies were scaled from millijoules to several kilojoules over the period 1970-1974, reaching approximately 10 J with SF 6 and transverse discharges, and using electron-beam initiation and elemental F 2 above 1000J. This demonstrated scalability to large energy with acceptable electrical efficiency is only one prerequisite for application of this gas laser in fusion; equally important matters are achievement of focusable, approximately 1 ns pulses, couplable to light-element targets, all from an affordable system. Exploratory MOPA experiments are reported which address control of HF laser beam focusability and pulse duration, using SF 6 -based experimental oscillator--amplifier sequences and Pockels' cell switching. Simultaneous multiline lasing with 2.6 less than or equal to lambda less than or equal to 3.1 μm and high specific gain and energy density are particularly important factors encountered with HF, where amplifier pumping and lasing occur in a substantially cw temporal relationship, even in less than 100 ns bursts. Time-resolved SF 6 --HI oscillator spectra contain 27 simultaneous lines from six vibrational bands. An apertured, SF 6 -hydrocarbon pin-discharge oscillator generates approximately 10 mJ of TEM 00 radiation, which is amplified to approximately 1 J in approximately 150 ns by a TEA amplifier and p []opagated tens of meters. A three-stage system coupling these elements through an approximately 1 ns electrooptic gate to a greater than 10 J, e-beam energized amplifier is under development. (auth)

Fat suppression in MR imaging with binomial pulse sequences

International Nuclear Information System (INIS)

Baudovin, C.J.; Bryant, D.J.; Bydder, G.M.; Young, I.R.

1989-01-01

This paper reports on a study to develop pulse sequences allowing suppression of fat signal on MR images without eliminating signal from other tissues with short T1. They have developed such a technique involving selective excitation of protons in water, based on a binomial pulse sequence. Imaging is performed at 0.15 T. Careful shimming is performed to maximize separation of fat and water peaks. A spin-echo 1,500/80 sequence is used, employing 90 degrees pulse with transit frequency optimized for water with null excitation of 20 H offset, followed by a section-selective 180 degrees pulse. With use of the binomial sequence for imagining, reduction in fat signal is seen on images of the pelvis and legs of volunteers. Patient studies show dramatic improvement in visualization of prostatic carcinoma compared with standard sequences

Custom pulse generator for RPC testing

International Nuclear Information System (INIS)

Gil, A.; Castro, E.; Diaz, J.; Fonte, P.; Garzon, J.A.; Montes, N.; Zapata, M.

2009-01-01

We present a pulse generator able to generate pulses statistically similar to the ones produced by RPC cells. The device generates up to four arrays of fast and narrow random-like pulses. Polarity, maximum amplitudes, widths and pulse rate in each channel may be modified independently in order to simulate different RPC setups and environments. This portable and cost-effective pulse generator is a versatile instrument for testing FE-Electronics and different real detector features related with the signal propagation inside the detector. It has been developed in the framework of the ESTRELA project of the HADES experiment at GSI.

Gas ultrasonic flow rate measurement through genetic-ant colony optimization based on the ultrasonic pulse received signal model

International Nuclear Information System (INIS)

Hou, Huirang; Zheng, Dandan; Nie, Laixiao

2015-01-01

For gas ultrasonic flowmeters, the signals received by ultrasonic sensors are susceptible to noise interference. If signals are mingled with noise, a large error in flow measurement can be caused by triggering mistakenly using the traditional double-threshold method. To solve this problem, genetic-ant colony optimization (GACO) based on the ultrasonic pulse received signal model is proposed. Furthermore, in consideration of the real-time performance of the flow measurement system, the improvement of processing only the first three cycles of the received signals rather than the whole signal is proposed. Simulation results show that the GACO algorithm has the best estimation accuracy and ant-noise ability compared with the genetic algorithm, ant colony optimization, double-threshold and enveloped zero-crossing. Local convergence doesn’t appear with the GACO algorithm until –10 dB. For the GACO algorithm, the converging accuracy and converging speed and the amount of computation are further improved when using the first three cycles (called GACO-3cycles). Experimental results involving actual received signals show that the accuracy of single-gas ultrasonic flow rate measurement can reach 0.5% with GACO-3 cycles, which is better than with the double-threshold method. (paper)

Design and array signal suggestion of array type pulsed eddy current probe for health monitoring of metal tubes

Energy Technology Data Exchange (ETDEWEB)

Shin, Young Kil [Dept. of Electrical Engineering, Kunsan National University, Kunsan (Korea, Republic of)

2015-10-15

An array type probe for monitoring metal tubes is proposed in this paper which utilizes peak value and peak time of a pulsed eddy current(PEC) signal. The probe consists of an array of encircling coils along a tube and the outside of coils is shielded by ferrite to prevent source magnetic fields from directly affecting sensor signals since it is the magnetic fields produced by eddy currents that reflect the condition of metal tubes. The positions of both exciter and sensor coils are consecutively moved automatically so that manual scanning is not necessary. At one position of send-receive coils, peak value and peak time are extracted from a sensor PEC signal and these data are accumulated for all positions to form an array type peak value signal and an array type peak time signal. Numerical simulation was performed using the backward difference method in time and the finite element method for spatial analysis. Simulation results showed that peak value increases and the peak appears earlier as the defect depth or length increases. The proposed array signals are shown to be excellent in reflecting the defect location as well as variations of defect depth and length within the array probe.

Climatización de una vivienda con energía geotérmica

OpenAIRE

González Elosua, Ignacio Isaías

2013-01-01

El presente proyecto consiste en el estudio, diseño y definición de una instalación de aprovechamiento de energía geotérmica para la climatización a lo largo de todo el año de una vivienda unifamiliar en la localidad de Fornells en el término municipal de Es Mercadal, en Menorca. Para ello, se ha calculado la demanda energética térmica requerida por la vivienda debido a su forma arquitectónica, materiales empleados y necesidades interiores, siguiendo criterios legales, funcionales y constr...

Energía eólica en España

Directory of Open Access Journals (Sweden)

Cayetano Espejo Marín

2004-01-01

Full Text Available Desde mediados de los años noventa se ha producido en España una expansiónextraordinaria del aprovechamiento de la energía eólica para la generación de electrici-dad. La disponibilidad de zonas con potencial eólico estimable junto con las políticas deapoyo a las energías renovables, sobre todo a la eólica, han contribuido a un enormedesarrollo industrial y tecnológico de este sector. España es líder mundial, tanto enpotencia instalada, donde ocupa el tercer puesto detrás de Alemania y Estados Unidos,como en número y volumen de empresas que participan en los distintos ámbitos de laenergía eólica. En este artículo se analizan las características del sector eólico español.

Quantitative evaluation of photoplethysmographic artifact reduction for pulse oximetry

Science.gov (United States)

Hayes, Matthew J.; Smith, Peter R.

1999-01-01

Motion artefact corruption of pulse oximeter output, causing both measurement inaccuracies and false alarm conditions, is a primary restriction in the current clinical practice and future applications of this useful technique. Artefact reduction in photoplethysmography (PPG), and therefore by application in pulse oximetry, is demonstrated using a novel non-linear methodology recently proposed by the authors. The significance of these processed PPG signals for pulse oximetry measurement is discussed, with particular attention to the normalization inherent in the artefact reduction process. Quantitative experimental investigation of the performance of PPG artefact reduction is then utilized to evaluate this technology for application to pulse oximetry. While the successfully demonstrated reduction of severe artefacts may widen the applicability of all PPG technologies and decrease the occurrence of pulse oximeter false alarms, the observed reduction of slight artefacts suggests that many such effects may go unnoticed in clinical practice. The signal processing and output averaging used in most commercial oximeters can incorporate these artefact errors into the output, while masking the true PPG signal corruption. It is therefore suggested that PPG artefact reduction should be incorporated into conventional pulse oximetry measurement, even in the absence of end-user artefact problems.

Planeamiento estratégico del sector de las fuentes no convencionales de energía renovable en Colombia

OpenAIRE

Torres Wilches, Carlos Rolando; Rojas Patiño, Alejandro; Higuera Rincón, Diana Astrid; Hernández Henríquez, Jorge Daniel; Calle Forero, Jorge Alberto

2017-01-01

xiv, 192 h. : il. ; 30 cm. A través de los años y en el ámbito mundial, la generación de energía eléctrica por medio de fuentes no convencionales de energía como el sol, el viento, la biomasa, y la energía mareomotriz, ha estado creciendo constantemente tanto en capacidad instalada (i.e., megawatt) como en número de proyectos implementados. Parte importante de este crecimiento se debe a la mejora continua en la tecnología de producción que utilizan entre otros los paneles so...

Quantum theory of NMR adiabatic pulses and their applications

International Nuclear Information System (INIS)

Ke, Y.

1993-01-01

Recently explosive developments of in vivo NMR spectroscopy (NMRS) and imaging (NMRI) in biological and medical sciences have resulted in the establishment of NMR as one of the most advanced major technique in life sciences. These developments have created huge demands for a variety of NMR adiabatic pulses with play a very important role in NMR experiments in vivo. In order to develop new NMR adiabatic pulses, a rigorous systematical quantum theory for this kind of pulses is greatly needed. Providing such a theory is one of the important goals of this dissertation. Quantum density matrix theory and product operator method have been used throughout this dissertation. Another goal, which is the major goal of this thesis research, is to use the quantum theory as a guide to develop new NMR adiabatic pulses and their applications. To fill this goal, a technique to construct a new type of adiabatic pulses, narrow band selective adiabatic pulses, has been invented, which is described through the example of constructing an adiabatic DANTE inversion pulse. This new adiabatic pulse is the first narrow band selective adiabatic pulses: Adiabatic homonuclear and heteronuclear spectral editing sequences. Unique to the first pulse sequence is a B 1 -field filter which is built by using two non-refocusing adiabatic full passage pulses to refocus the wanted signal and dephase unwanted signals. This extra filter greatly enhance the editing efficiency. Unlike commonly used heteronuclear spectral editing sequences which depend on the polarization transfer or spectral subtraction by phase cycling techniques, the second pulse sequences accomplishes the editing of heteronuclear J-coupled signals based on the fact that this sequence is transparent to the uncoupled spins and is equivalent a 90 degrees excitation pulse to the heteronuclear J-coupled spins. Experimental results have confirmed the ability of spectral editing with these two new sequences

Desarrollo de pigmentos cerámicos multifuncionales orientados a la mejora de la eficiencia energética en edificación

OpenAIRE

Aranzabe Basterrechea, Estíbaliz

2017-01-01

268 p. El sector de la edificación y en concreto la climatización de edificios es un sectorprioritario a la hora de implementar mejoras de eficiencia energética. Así lo demuestrala estrategia energética de la Unión Europea (objetivo 20-20-20) y la EstrategiaEnergética de Euskadi 2020 que establecen claras líneas de actuación entre las cuales seencuentra la reducción del consumo de energía en los edificios y en el hogar.La rehabilitación de edificios se presenta como una de las claves para ...

Desarrollo de un modelo de determinación de cash-flows para un proyecto de energía eólica

OpenAIRE

Irene Clara Pisón Fernández; Félix Puime Guillén; Miguel Ángel Crespo Cibrán

2015-01-01

En este trabajo se analiza la problemática asociada a la producción de energía eléctrica de origen renovable, y se ofrece un modelo de definición de las variables en las que se apoya el plan de negocio de energía eólica. El plan de viabilidad muestra que los cash-flows para el accionista obtenidos en este tipo de proyectos permiten afrontar las inversiones futuras con una rentabilidad suficiente, que apunta al sector de energías renovables, y en particular al de energía eólica, como estratégi...

Novel Signal Noise Reduction Method through Cluster Analysis, Applied to Photoplethysmography.

Science.gov (United States)

Waugh, William; Allen, John; Wightman, James; Sims, Andrew J; Beale, Thomas A W

2018-01-01

Physiological signals can often become contaminated by noise from a variety of origins. In this paper, an algorithm is described for the reduction of sporadic noise from a continuous periodic signal. The design can be used where a sample of a periodic signal is required, for example, when an average pulse is needed for pulse wave analysis and characterization. The algorithm is based on cluster analysis for selecting similar repetitions or pulses from a periodic single. This method selects individual pulses without noise, returns a clean pulse signal, and terminates when a sufficiently clean and representative signal is received. The algorithm is designed to be sufficiently compact to be implemented on a microcontroller embedded within a medical device. It has been validated through the removal of noise from an exemplar photoplethysmography (PPG) signal, showing increasing benefit as the noise contamination of the signal increases. The algorithm design is generalised to be applicable for a wide range of physiological (physical) signals.

8th conference on Ultra-Wideband Short-Pulse Electromagnetics

CERN Document Server

Tyo, J. Scott; Baum, Carl E; Ultra-Wideband Short-Pulse Electromagnetics 8; UWBSP8

2007-01-01

The purpose of the Ultra-Wideband Short-Pulse Electromagnetics Conference series is to focus on advanced technologies for the generation, radiation and detection of ultra-wideband short pulse signals, taking into account their propagation and scattering from and coupling to targets of interest. This Conference series reports on developments in supporting mathematical and numerical methods and presents current and potential future applications of the technology. Ultra-Wideband Short-Pulse Electromagnetics 8 is based on the American Electromagnetics 2006 conference held from June 3-7 in Albuquerque, New Mexico. Topical areas covered in this volume include pulse radiation and measurement, scattering theory, target detection and identification, antennas, signal processing, and communications.

Pulse stuttering as a remedy for aliased ground backscatter

Science.gov (United States)

Bowhill, S. A.

1983-12-01

An algorithm that aides in the removal of ground scatter from low frequency Mesosphere, Stratosphere, Troposphere (MST) radar signals is examined. The unwanted ground scatter is shown as a sequence of velocity plots which are almost typical at the various altitudes. The interpulse period is changed in a cyclic way, thereby destroying the coherence of the unwanted signal. The interpulse period must be changed by an amount at least equal to the transmitted pulse width, and optimum performance is obtained when the number of different interpulse period occupies a time span greater than the coherence time of the unwanted signal. Since a 20-msec pulse width is used, it was found convenient to cycle through 50 pulses, the interpulse period changing from 2 msec to 3 msec during the 1/8-second time. This particular pattern of interpulse periods was provided by a software radar controller. With application of this algorithm, the unwanted scatter signal becomes incoherent from one pulse to the next, and therefore is perceived as noise by the coherent integrator and correlator.

Diagnosis of Obstructive Sleep Apnea Using Pulse Oximeter Derived Photoplethysmographic Signals

Science.gov (United States)

Romem, Ayal; Romem, Anat; Koldobskiy, Dafna; Scharf, Steven M.

2014-01-01

Objectives: Increasing awareness of the high prevalence of obstructive sleep apnea (OSA) and its impact on health in conjunction with high cost, inconvenience, and short supply of in-lab polysomnography (PSG) has led to the development of more convenient, affordable, and accessible diagnostic devices. We evaluated the reliability and accuracy of a single-channel (finger pulse-oximetry) photoplethysmography (PPG)-based device for detection of OSA (Morpheus Ox). Methods: Among a cohort of 73 patients referred for in-laboratory evaluation of OSA, 65 were simultaneously monitored with the PPG based device while undergoing PSG. Among these, 19 had significant cardiopulmonary comorbidities. Using the PSG as the “gold standard,” the sensitivity, specificity, negative predictive value (NPV), positive predictive value (PPV), as well as the positive likelihood ratio (+LR) for an apnea hypopnea index (AHI)PSG > 5/h and AHIPSG > 15/h were calculated for the PPG. Results: Valid results were available for 65 subjects. Mean age: 52.1 ± 14.2, Male: 52%, and BMI: 36.3 ± 9.7 kg/m2. Positive correlation was found between PPG-derived and PSG-derived AHI (r = 0.81, p 5/h, sensitivity was 80%, specificity 86%, PPV 93%, NPV 68%, and +LR was 5.9. For AHIPSG > 15/h, sensitivity was 70%, specificity 91%, PPV 80%, NPV 85%, and +LR was 7.83. The corresponding areas under the receiver operator curves were 0.91 and 0.9. Conclusions: PPG-derived data compare well with simultaneous in-lab PSG in the diagnosis of suspected OSA among patients with and without cardiopulmonary comorbidities. Citation: Romem A; Romem A; Koldobskiy D; Scharf SM. Diagnosis of obstructive sleep apnea using pulse oximeter derived photoplethysmographic signals. J Clin Sleep Med 2014;10(3):285-290. PMID:24634626

Viability of a Bioelectrical Signal Acquisition System Energized by Cellphone with NFC.

Science.gov (United States)

Kay, Marcel Seiji; Iaione, Fábio

2015-01-01

Currently, smartphones are used in various systems in the medical field due to the presence of various features, notably Near Field Communication (NFC). NFC utilizes communication technology and an energy supply based on electromagnetic induction. One of the most common medical tests is the electrocardiogram (ECG), through which various heart diseases can be diagnosed. The objective of this study is to evaluate the feasibility of providing power to a bioelectrical signal acquisition module using a mobile phone with NFC. After testing it was indicated that it is possible to construct a passive module to acquire ECG signals using NFC mobile phone.

Determination of the wavelength dependence of the differential pathlength factor from near-infrared pulse signals

Science.gov (United States)

Kohl, Matthias; Nolte, Christian; Heekeren, Hauke R.; Horst, Susanne; Scholz, Udo; Obrig, Hellmuth; Villringer, Arno

1998-06-01

For the calculation of changes in oxyhaemoglobin, deoxyhaemoglobin and the redox state of cytochrome-c-oxidase from attenuation data via a modified Beer-Lambert equation the wavelength dependence of the differential pathlength factor (DPF) has to be taken into account. The DPF, i.e. the ratio of the mean optical pathlength and the physical light source-detector separation at each wavelength, determines the crosstalk between the different concentrations and is therefore essential for a sensitive detection of chromophore changes. Here a simple method is suggested to estimate the wavelength dependence of the DPF from pulse-induced attenuation changes measured on the head of adult humans. The essence is that the DPF is the ratio of the attenuation changes over absorption coefficient changes, and that the spectral form of the pulse correlated absorption coefficient change can be assumed to be proportional to the extinction coefficient of blood. Indicators for the validity of the DPF derived for wavelengths between 700 and 970 nm are the stability of the calculated haemoglobin and cytochrome signals with variations of the wavelength range included for their calculation and its overall agreement with the data available from the literature.

Seguridad energética rusa: entre Europa y China

Directory of Open Access Journals (Sweden)

Antonio Sánchez

2008-05-01

Full Text Available Dentro de la seguridad energética rusa aparece como una debilidad importante la concentración de recursos en unos pocos clientes, en concreto en la UE. Por este motivo, las autoridades rusas están tratando de diversificar destinos de venta, tratando de abrir otros mercados, en especial en extremo oriente y, en particular en China. Esto acrecienta su seguridad energética, pero debilita la europea en caso de que la UE no adopte medidas activas. El abastecimiento a Europa desde Rusia, especialmente de gas, depende también de tres grandes limitaciones. En primer lugar, que existan nuevos yacimientos y su posibilidad de movilizarlos conforme aumenten las necesidades europeas. En segundo lugar, aparece el problema del surgimiento de competidores por el gas ruso y, en particular, recientemente se ha subrayado el papel de China como futuro cliente de gas ruso. En tercer lugar, se encuentra la posibilidad de que Rusia pueda ejercer un control especial sobre la oferta de gas mundial, que condicione en cantidad o/y precio el abastecimiento a Europa.

Real-time pulse deinterleaving using digital delay line techniques

Science.gov (United States)

Lentz, L. F.; Palermo, T. J.

This paper describes an implementation of a tracking pulse sorter based on predictive gating techniques. Real-time pulse sorters or pulse train gating devices have been utilized by the ELINT signal analyst for many years. The more elementary of these devices employed a retriggerable delay interval and an acceptance gate, which were used in predictive fashion to track pulse trains whose PRIs fall within the limits of the programmed delay interval. This design utilizes the pulse hit/miss history of individual track files in a variation of a sequential observer detection algorithm. Use of a digital delay line with pulse history allows multiple pulse trains to be tracked simultaneously and independently without interference. The design also provides flexibility in lock-on and track criteria to allow maintenance of acquisition probability and false alarm rate in dense signal environments and with low SNRs. The hardware provides time interval resolution to 12.5 nsec and covers a PRI range of 50 microsec to 50 msec.

ASL: Comparison of presaturation and RF pulse optimization

DEFF Research Database (Denmark)

Holm, David; Sidaros, Karam

2005-01-01

In arterial spin labelling, the difference between the tag and control image is on the order of 1% of the equilibrium magnetization. A small offset between the images not related to perfusion, can therefore lead to large errors in the measured perfusion. One source of error is non-ideal RF pulses...... resulting in the inversion pulse affecting the acquired signal from the imaging area. This systematic error can be reduced by increasing the gap between the inversion and imaging regions, by using optimized inversion pulses e.g. FOCI1 or by saturating the signal from static tissue in the imaging area prior...

De molinos y quijotes. Energía eólica y cooperativismo en el sur bonaerense

Directory of Open Access Journals (Sweden)

Luciana Clementi

2014-06-01

Full Text Available El constante aumento en la demanda de energía evidenciado en Argentina, sumado al fuerte interés nacional por alcanzar mayor seguridad energética, profundiza la necesidad de nuevas inversiones en el sector energético. Sin embargo, la dependencia que sufre el país en relación a los hidrocarburos hace peligrar el abastecimiento en el largo plazo. En este contexto, aparecen en la última década proyectos de producción de energía renovable, incentivados por un contexto mundial donde se alienta el desarrollo de fuentes energéticas que contribuyan a avanzar hacia un modelo más sustentable. En este escenario, interesa en este trabajo analizar el rol de las cooperativas eléctricas fuertemente ancladas en la Provincia de Buenos Aires, en la ejecución de proyectos locales que contemplan la producción de energía eólica en el Sur bonaerense, para reflexionar acerca de las oportunidades y barreras a las que se enfrentan. The constant increase of energy demands in Argentina together with the strong national interest to obtain a higher energy security, deepens the need of new investments in the energy sector. However, the dependence of the country on hidrocarbons threatens the supply in the long-term. In this context appear in the last decade, renewable energy production projects, triggered by a global context which encourages the development of energy sources that favor a cleaner and more sustainable model. In this scenario, it is of interest in this paper to analyze the role of cooperatives of electricity well-established in the Province of Buenos Aires, mainly in the performance of local projects that consider eolic energy production in the South of Buenos Aires, in order to reflect upon the new opportunities as well as the barriers they must deal.

Avaliação da eficiência energética em uma indústria de painéis compensado

OpenAIRE

Silva, Dimas Agostinho da

2013-01-01

Este trabalho trata do perfil e do uso de energia em uma indústria de painéis compensado no Brasil. O seu objetivo geral é corroborar para a melhoria da competitividade da indústria de compensado nacional. Especificamente visou conhecer o perfil do consumo energético na indústria, avaliar possibilidade de ganhos de eficiência no componente energético do processo produtivo e disponibilizar modelos matemáticos de consumo energético aplicado às indústrias de painéis compensado. O trabalho foi de...

Proyectos pilotos WHIX de energía renovable y seguridad ambiental en El Salvador.

OpenAIRE

Ochoa Córdova, Carlos Roberto

2008-01-01

El Programa WHIX aporta proyectos de Energía y Medio Ambiente para abrir un diálogo entre los militares de la Región, organizaciones gubernamentales y no-gubernamentales y sus equivalentes en los EE.UU. Este programa cataliza proyectos de energía renovable y el medioambiente para demostrar y validar estas tecnologías en los países de la región. Al mismo tiempo provee un foro de intercambio internacional de las “Mejores Prácticas” y la oportunidad de trabajar en conjunto en promisorias investi...

Pulse discrimination of background and gamma-ray source by digital pulse shape discrimination in a BF3 detector

International Nuclear Information System (INIS)

Kim, Jinhyung; Kim, J. H.; Choi, H. D.

2014-01-01

As a representative method of non-destructive assay, accurate neutron measurement is difficult due to large background radiation such as γ-ray, secondary radiation, spurious pulse, etc. In a BF 3 detector, the process of signal generation is different between neutron and other radiations. As the development of detection technique, all of signal data can be digitized by digital measurement method. In the previous study, Applied Nuclear Physics Group in Seoul National University has developed digital Pulse Shape Discrimination (PSD) method using digital oscilloscope. In this study, optimization of parameters for pulse discrimination is discussed and γ-ray region is determined by measuring 60 Co source. The background signal of BF 3 detector is discriminated by digital PSD system. Parameters for PSD are optimized through FOM calculation. And the γ-ray region is determined by measuring 60 Co source. In the future, the performance of developed system will be tested in low and high intensity neutron field

Intraband effects on ultrafast pulse propagation in semiconductor ...

Indian Academy of Sciences (India)

High bit-rate (>10 Gb/s) signals are composed of very short pulses and propagation of such pulses through a semiconductor optical amplifier (SOA) requires consideration of intraband phenomena. Due to the intraband effects, the propagating pulse sees a fast recovering nonlinear gain which introduces less distortion in the ...

Evaluación de las medidas de eficiencia energética para la estación antártica ecuatoriana Pedro Vicente Maldonado a través del modelo de energía calibrada para edificaciones

Directory of Open Access Journals (Sweden)

Isabel Miño

2015-08-01

Full Text Available En la Antártica, un continente sensible a las actividades humanas y un lugar estratégico para la investigación de los efectos producidos por el cambio climático, es importante que los proyectos desarrollados ahí minimicen su impacto medioambiental. Bajo este concepto, la estación antártica Pedro Vicente Maldonado, construida en 1990 y operada por Ecuador durante el verano austral, se convertirá dentro de pocos años en una estación permanente. Por ello y con el fin de optimizar el consumo energético, se han analizado diversas medidas de eficiencia energética de acuerdo a un modelo energético basado en el actual consumo de diésel para calefacción. Los resultados de este estudio demuestran que los elementos de la envolvente del edificio, por donde se pierde gran parte de la energía, son el piso y el techo. Por otro lado, debido a la baja relación ventana-paredes de la estación, la reducción en el consumo de diésel generado por el uso de vidrios triple y cuádruple no es significativa. Al combinar diferentes medidas de eficiencia energética, se puede ahorrar hasta un 50% del consumo anual de diésel para calefacción si se compara con el consumo que tendría la estación actual operando en forma permanente. Este estudio servirá de referencia para implementar los cambios necesarios en dicha estación.

Digital pulse processing: new possibilities in nuclear spectroscopy

International Nuclear Information System (INIS)

Warburton, W.K.; Momayezi, M.; Hubbard-Nelson, B.; Skulski, W.

2000-01-01

Digital pulse processing is a signal processing technique in which detector (preamplifier output) signals are directly digitized and processed to extract quantities of interest. This approach has several significant advantages compared to traditional analog signal shaping. First, analyses can be developed which take pulse-by-pulse differences into account, as in making ballistic deficit compensations. Second, transient induced charge signals, which deposit no net charge on an electrode, can be analyzed to give, for example, information on the position of interaction within the detector. Third, deadtimes from transient overload signals are greatly reduced, from tens of μs to hundreds of ns. Fourth, signals are easily captured, so that more complex analyses can be postponed until the source event has been deemed 'interesting'. Fifth, signal capture and processing may easily be based on coincidence criteria between different detectors or different parts of the same detector. XIAs recently introduced CAMAC module, the DGF-4C, provides many of these features for four input channels, including two levels of digital processing and a FIFO for signal capture for each signal channel. The first level of digital processing is 'immediate', taking place in a gate array at the 40 MHz digitization rate, and implements pulse detection, pileup inspection, trapezoidal energy filtering, and control of an external 25.6 μs long FIFO. The second level of digital processing is provided by a digital signal processor (DSP), where more complex algorithms can be implemented. To illustrate digital pulse processing's possibilities, we describe the application of the DGF-4C to a series of experiments. The first, for which the DGF was originally developed, involves locating gamma-ray interaction sites within large segmented Ge detectors. The goal of this work is to attain spatial resolutions of order 2 mm σ within 70 mm x 90 mm detectors. We show how pulse shape analysis allows ballistic

Concerning the generation of very high pressures for EOS studies with ultra-high power laser pulses

International Nuclear Information System (INIS)

Wood, L.L.; Keeler, R.N.; Nuckolls, J.H.

1977-07-01

The use of basic physical and geometric principles, coupled with current laser technology, seems likely to extend experimental hyperbaric physics investigations from the megabar region into the portions of parameter space in which the ideal (degenerate) Fermi gas approximation is valid for even the highest Z materials. Implosions and speed-multiplying rectilinear stacks of flat plates seem particularly apt techniques for the near-term, transient attainment of pressure of 10 9 atmospheres in the laboratory, and laser-energized pulsed x-ray ''cameras'' appear suitable for analyzing the basic properties of matter under such conditions

Sensitive detection of chlorine in iron oxide by single pulse and dual pulse laser-induced breakdown spectroscopy

Science.gov (United States)

Pedarnig, J. D.; Haslinger, M. J.; Bodea, M. A.; Huber, N.; Wolfmeir, H.; Heitz, J.

2014-11-01

The halogen chlorine is hard to detect in laser-induced breakdown spectroscopy (LIBS) mainly due to its high excited state energies of 9.2 and 10.4 eV for the most intense emission lines at 134.72 nm and 837.59 nm, respectively. We report on sensitive detection of Cl in industrial iron oxide Fe2O3 powder by single-pulse (SP) and dual-pulse (DP) LIBS measurements in the near infrared range in air. In compacted powder measured by SP excitation (Nd:YAG laser, 532 nm) Cl was detected with limit of detection LOD = 440 ppm and limit of quantitation LOQ = 720 ppm. Orthogonal DP LIBS was studied on pressed Fe2O3 pellets and Fe3O4 ceramics. The transmission of laser-induced plasma for orthogonal Nd:YAG 1064 nm and ArF 193 nm laser pulses showed a significant dependence on interpulse delay time (ipd) and laser wavelength (λL). The UV pulses (λL = 193 nm) were moderately absorbed in the plasma and the Cl I emission line intensity was enhanced while IR pulses (λL = 1064 nm) were not absorbed and Cl signals were not enhanced at ipd = 3 μs. The UV laser enhancement of Cl signals is attributed to the much higher signal/background ratio for orthogonal DP excitation compared to SP excitation and to the increased plasma temperature and electron number density. This enabled measurement at a very short delay time of td ≥ 0.1 μs with respect to the re-excitation pulse and detection of the very rapidly decaying Cl emission with higher efficiency.

Strategies for shortening the output pulse of silicon photomultipliers

OpenAIRE

Antoranz Canales, Pedro; Miranda Pantoja, José Miguel; Yebras Rivera, José Manuel

2012-01-01

In this work, three strategies for shortening the output pulse of a silicon photomultiplier (SiPM) are reported. The first strategy is passive filtering, where band-pass filtering removes the lowest frequency components in the signal, getting a noticeable reduction in pulse width (a compression ratio of 10: 1 was obtained). In the second place, a reflectometric scheme is proposed where the amplified signal coming from the SiPM is injected into a signal splitter with one of its stubs connected...

A fast random walk algorithm for computing the pulsed-gradient spin-echo signal in multiscale porous media.

Science.gov (United States)

Grebenkov, Denis S

2011-02-01

A new method for computing the signal attenuation due to restricted diffusion in a linear magnetic field gradient is proposed. A fast random walk (FRW) algorithm for simulating random trajectories of diffusing spin-bearing particles is combined with gradient encoding. As random moves of a FRW are continuously adapted to local geometrical length scales, the method is efficient for simulating pulsed-gradient spin-echo experiments in hierarchical or multiscale porous media such as concrete, sandstones, sedimentary rocks and, potentially, brain or lungs. Copyright © 2010 Elsevier Inc. All rights reserved.

Phantom with pulsatile arteries to investigate the influence of blood vessel depth on pulse oximeter signal strength.

Science.gov (United States)

Stuban, Norbert; Niwayama, Masatsugu; Santha, Hunor

2012-01-01

This paper describes a three-layer head phantom with artificial pulsating arteries at five different depths (1.2 mm, 3.7 mm, 6.8 mm, 9.6 mm and 11.8 mm). The structure enables formation of spatially and temporally varying tissue properties similar to those of living tissues. In our experiment, pressure pulses were generated in the arteries by an electronically controlled pump. The physical and optical parameters of the layers and the liquid in the artificial arteries were similar to those of real tissues and blood. The amplitude of the pulsating component of the light returning from the phantom tissues was measured at each artery depth mentioned above. The build-up of the in-house-developed pulse oximeter used for performing the measurements and the physical layout of the measuring head are described. The radiant flux generated by the LED on the measuring head was measured to be 1.8 mW at 910 nm. The backscattered radiant flux was measured, and found to be 0.46 nW (0.26 ppm), 0.55 nW (0.31 ppm), and 0.18 nW (0.10 ppm) for the 1.2 mm, 3.7 mm and 6.8 mm arteries, respectively. In the case of the 9.6 mm and 11.8 mm arteries, useful measurement data were not obtained owing to weak signals. We simulated the phantom with the arteries at the above-mentioned five depths and at two additional ones (2.5 mm and 5.3 mm in depth) using the Monte Carlo method. The measurement results were verified by the simulation results. We concluded that in case of 11 mm source-detector separation the arteries at a depth of about 2.5 mm generate the strongest pulse oximeter signal level in a tissue system comprising three layers of thicknesses: 1.5 mm (skin), 5.0 mm (skull), and >50 mm (brain).

Phantom with Pulsatile Arteries to Investigate the Influence of Blood Vessel Depth on Pulse Oximeter Signal Strength

Directory of Open Access Journals (Sweden)

Hunor Santha

2012-01-01

Full Text Available This paper describes a three-layer head phantom with artificial pulsating arteries at five different depths (1.2 mm, 3.7 mm, 6.8 mm, 9.6 mm and 11.8 mm. The structure enables formation of spatially and temporally varying tissue properties similar to those of living tissues. In our experiment, pressure pulses were generated in the arteries by an electronically controlled pump. The physical and optical parameters of the layers and the liquid in the artificial arteries were similar to those of real tissues and blood. The amplitude of the pulsating component of the light returning from the phantom tissues was measured at each artery depth mentioned above. The build-up of the in-house-developed pulse oximeter used for performing the measurements and the physical layout of the measuring head are described. The radiant flux generated by the LED on the measuring head was measured to be 1.8 mW at 910 nm. The backscattered radiant flux was measured, and found to be 0.46 nW (0.26 ppm, 0.55 nW (0.31 ppm, and 0.18 nW (0.10 ppm for the 1.2 mm, 3.7 mm and 6.8 mm arteries, respectively. In the case of the 9.6 mm and 11.8 mm arteries, useful measurement data were not obtained owing to weak signals. We simulated the phantom with the arteries at the above-mentioned five depths and at two additional ones (2.5 mm and 5.3 mm in depth using the Monte Carlo method. The measurement results were verified by the simulation results. We concluded that in case of 11 mm source-detector separation the arteries at a depth of about 2.5 mm generate the strongest pulse oximeter signal level in a tissue system comprising three layers of thicknesses: 1.5 mm (skin, 5.0 mm (skull, and > 50 mm (brain.

2-Dimension pulse shape discriminator for phoswich detector based on FPGA

International Nuclear Information System (INIS)

Ji Jianfeng; Liu Congzhan; Zhang Zhi

2011-01-01

It improves the data acquire system for the pulse signal based on digital front-rear pulse shape discrimination system. It adds pulse width information into the pulse's data package. Base on this, we divide the pulse event process into two process, on line coast process and offline accurate process: the online process sets a big threshold, just save the data of the event below this threshold; the offline process uses the acquired data, get the pulse amplitude and pulse width, and then according the spectrum's real shape, set the accurate threshold. this design resolves the problem that the detector's decay time change with the temperature; at the same time, it can correct the system's distortion when the input signal at small amplitude, improves the discrimination system's accuracy. (authors)

The role of fluid compression in energy conversion and particle energization during magnetic reconnection

Science.gov (United States)

Li, X.; Guo, F.; Li, G.; Li, H.

2016-12-01

Theories of particle transport and acceleration have shown that fluid compression is the leading mechanism for particle acceleration and plasma energization. However, the role of compression in particle acceleration during magnetic reconnection is unclear. We use two approaches to study this issue. First, using fully kinetic simulations, we quantitatively calculate the effect of compression in energy conversion and particle energization during magnetic reconnection for a range of plasma beta and guide field. We show that compression has an important contribution for the energy conversion between the bulk kinetic energy and the internal energy when the guide field is smaller than the reconnecting component. Based on this result, we then study the large-scale reconnection acceleration by solving the Parker's transport equation in a background reconnecting flow provided by MHD simulations. Due to the compression effect, the simulations suggest fast particle acceleration to high energies in the reconnection layer. This study clarifies the nature of particle acceleration in reconnection layer, and may be important to understand particle acceleration and plasma energization during solar flares.

Estudio regional del potencial de secado con aire natural y energía solar

Directory of Open Access Journals (Sweden)

Jorge Domínguez P.

1983-09-01

Full Text Available En este artículo se presenta y aplica una metodología de trabajo basada en la técnica de simulación matemática y desarrollada con el fin de realizar estudios sobre el potencial de secado de productos agropecuarios con aire natural y energía solar de regiones tropicales. La metodología se basa en el uso de un programa de computador e Incluye otros elementos metodológicos en relación con el manejo de la información meteorológica, el patrón de operación del ventilador, el uso de energía solar y la interpretación de los resultados con el fin de optimizar el sistema. Se reportan los resultados del estudio del potencial de secado con aire natural y energía solar de Tuluá (Valle y se proporcionan recomendaciones específicas para la implementación de sistemas de secado a bala temperatura en la Reglón.

Effect of pulse sequence parameter selection on signal strength in positive-contrast MRI markers for MRI-based prostate postimplant assessment

Energy Technology Data Exchange (ETDEWEB)

Lim, Tze Yee [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, 1515 Holcombe Boulevard, Houston, Texas 77030 and The University of Texas at Houston Graduate School of Biomedical Sciences, 6767 Bertner Avenue, Houston, Texas 77030 (United States); Kudchadker, Rajat J., E-mail: rkudchad@mdanderson.org; Wang, Jihong; Ibbott, Geoffrey S. [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, 1515 Holcombe Boulevard, Houston, Texas 77030 (United States); Stafford, R. Jason [Department of Imaging Physics, The University of Texas MD Anderson Cancer Center, 1515 Holcombe Boulevard, Houston, Texas 77030 (United States); MacLellan, Christopher [Department of Imaging Physics, The University of Texas MD Anderson Cancer Center, 1515 Holcombe Boulevard, Houston, Texas 77030 and The University of Texas at Houston Graduate School of Biomedical Sciences, 6767 Bertner Avenue, Houston, Texas 77030 (United States); Rao, Arvind [Department of Bioinformatics and Computational Biology, The University of Texas MD Anderson Cancer Center, 1515 Holcombe Boulevard, Houston, Texas 77030 (United States); Frank, Steven J. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, 1515 Holcombe Boulevard, Houston, Texas 77030 (United States)

2016-07-15

Purpose: For postimplant dosimetric assessment, computed tomography (CT) is commonly used to identify prostate brachytherapy seeds, at the expense of accurate anatomical contouring. Magnetic resonance imaging (MRI) is superior to CT for anatomical delineation, but identification of the negative-contrast seeds is challenging. Positive-contrast MRI markers were proposed to replace spacers to assist seed localization on MRI images. Visualization of these markers under varying scan parameters was investigated. Methods: To simulate a clinical scenario, a prostate phantom was implanted with 66 markers and 86 seeds, and imaged on a 3.0T MRI scanner using a 3D fast radiofrequency-spoiled gradient recalled echo acquisition with various combinations of scan parameters. Scan parameters, including flip angle, number of excitations, bandwidth, field-of-view, slice thickness, and encoding steps were systematically varied to study their effects on signal, noise, scan time, image resolution, and artifacts. Results: The effects of pulse sequence parameter selection on the marker signal strength and image noise were characterized. The authors also examined the tradeoff between signal-to-noise ratio, scan time, and image artifacts, such as the wraparound artifact, susceptibility artifact, chemical shift artifact, and partial volume averaging artifact. Given reasonable scan time and managable artifacts, the authors recommended scan parameter combinations that can provide robust visualization of the MRI markers. Conclusions: The recommended MRI pulse sequence protocol allows for consistent visualization of the markers to assist seed localization, potentially enabling MRI-only prostate postimplant dosimetry.

Digital signal processing for He3 proportional counter

International Nuclear Information System (INIS)

Zeynalov, Sh.S.; Ahmadov, Q.S.

2010-01-01

Full text : Data acquisition systems for nuclear spectroscopy have traditionally been based on systems with analog shaping amplifiers followed by analog-to-digital converters. Recently, however, new systems based on digital signal processing make possible to replace the analog shaping and timing circuitry the numerical algorithms to derive properties of the pulse such as its amplitude. DSP is a fully numerical analysis of the detector pulse signals and this technique demonstrates significant advantages over analog systems in some circumstances. From a mathematical point of view, one can consider the signal evolution from the detector to the ADC as a sequence of transformations that can be described by precisely defined mathematical expressions. Digital signal processing with ADCs has the possibility to utilize further information on the signal pulses from radiation detectors. In the experiment each step of the signal generation in the 3He filled proportional counter was described using digital signal processing techniques (DSP). The electronic system has consisted of a detector, a preamplifier and a digital oscilloscope. The pulses from the detector were digitized using a digital storage oscilloscope. This oscilloscope allowed signal digitization with accuracy of 8 bit (256 levels) and with frequency of up to 5 * 10 8 samples/s. As a neutron source was used Cf-252. To obtain detector output current pulse I(t) created by the motions of the ions/electrons pairs was written an algorithm which can easily be programmed using modern computer programming languages.

Short-pulse propagation in fiber optical parametric amplifiers

DEFF Research Database (Denmark)

Cristofori, Valentina

Fiber optical parametric amplifiers (FOPAs) are attractive because they can provide large gain over a broad range of central wavelengths, depending only on the availability of a suitable pump laser. In addition, FOPAs are suitable for the realization of all-optical signal processing functionalities...... transfer can be reduced in saturated F OPAs. In order to characterize propagation impairments such as dispersion and Kerr effect, affecting signals reaching multi-terabit per second per channel, short pulses on the order of 500 fs need to be considered. Therefore, a short pulses fiber laser source...... is implemented to obtain an all-fiber system. The advantages of all fiber-systems are related to their reliability, long-term stability and compactness. Fiber optical parametric chirped pulse amplification is promising for the amplification of such signals thanks to the inherent compatibility of FOPAs with fiber...

Combining multi-pulse excitation and chirp coding in contrast-enhanced ultrasound imaging

International Nuclear Information System (INIS)

Crocco, M; Sciallero, C; Trucco, A; Pellegretti, P

2009-01-01

The development of techniques to separate the response of the contrast agent from that of the biological tissues is of great importance in ultrasound medical imaging. In the literature, one can find various solutions involving the use of multiple transmitted signals and the weighted sum of related echoes. In this paper, the combination of one of these multi-pulse techniques with a coded excitation is proposed and assessed. Coded excitation has been used mainly to increase the signal-to-noise ratio (SNR) and the penetration depth, provided that a matched filtering is applied in the reception chain. However, it has been shown that a signal with a long duration time also increases the backscattered echoes produced by the microbubbles and, consequently, the contrast-to-tissue ratio. Therefore, the implementation of a multi-pulse technique using a long coded pulse can yield a better contrast-to-tissue ratio and SNR. This paper investigates the combination of the linear chirp pulse with a multi-pulse technique based on the transmission of three pulses. The performance was evaluated using both simulated and real signals, assessing the improvement in the contrast-to-tissue ratio and SNR, the visual quality of the images obtained and the axial accuracy. A comparison with the same multi-pulse technique implemented using a traditional amplitude-modulated pulse revealed that the deployment of a chirp pulse produces several noticeable advantages and only a minor drawback

El sub-sector de distribución de energía eléctrica en Colombia

Directory of Open Access Journals (Sweden)

Mauricio Martín Delvasto

1999-07-01

Full Text Available El sector de energía eléctrica en Colombia, ha experimentado en los últimos 18 meses una transformación total que persigue la utilización eficiente de los recursos, además de tener el control administrativo y operacional de las empresas de generación y distribución de energía con el propósito de lograr mayor cobertura nacional y aumentar considerablemente la calidad en la prestación del servicio de energía. A continuación se describen los principales elementos, incluyendo aquellos de naturaleza financiera, que originaron su transformación, así como los resultados, a corto y mediano plazo que se pretenden obtener con los procesos de privatización de un sector, sin ninguna duda, fundamental para el desarrollo de nuestro país.

Pulse Doppler radar

CERN Document Server

Alabaster, Clive

2012-01-01

This book is a practitioner's guide to all aspects of pulse Doppler radar. It concentrates on airborne military radar systems since they are the most used, most complex, and most interesting of the pulse Doppler radars; however, ground-based and non-military systems are also included. It covers the fundamental science, signal processing, hardware issues, systems design and case studies of typical systems. It will be a useful resource for engineers of all types (hardware, software and systems), academics, post-graduate students, scientists in radar and radar electronic warfare sectors and milit

Comments on the stochastic characteristics of fission chamber signals

International Nuclear Information System (INIS)

Pál, L.; Pázsit, I.; Elter, Zs.

2014-01-01

This paper reports on theoretical investigations of the stochastic properties of the signal series of ionisation chambers, in particular fission chambers. First, a simple and transparent derivation is given of the higher order moments of the random detector signal for incoming pulses with a non-homogeneous Poisson distribution and random pulse heights and arbitrary shape. Exact relationships are derived for the higher order moments of the detector signal, which constitute a generalisation of the so-called higher order Campbelling techniques. The probability distribution of the number of time points when the signal exceeds a certain level is also derived. Then, a few simple pulse shapes and amplitude distributions are selected as idealised models of the detector signals. Assuming that the incoming particles form a homogeneous Poisson process, explicit expressions are given for the higher order moments of the signal and the number of level crossings in a given time interval for the selected pulse shapes

Impacto de programas de eficiencia energética eléctrica, estudio de caso: Empresas alimentarias en Cuenca, Ecuador

Directory of Open Access Journals (Sweden)

Galo Carrillo-Rojas

2014-01-01

Full Text Available El estudio exploratorio muestra los resultados de aplicación de programas de eficiencia energética eléctrica en 7 empresas alimentarias en Cuenca, Ecuador. La investigación contempló fases de diagnóstico, intervención y evaluación. Se condujo un análisis comparativo entre las empresas: consumo de energía versus producción, análisis de calidad de energía, relación cumplimiento/consumo específico de energía, e impacto sobre emisiones CO2. Los resultados revelaron que la aceptación hacia las recomendaciones de ahorro, se basa en el nivel de inversión y la voluntad/disponibilidad administrativa. El estudio mostró que las intervenciones tuvieron un efecto parcial sobre la reducción del consumo específico de energía en 4 empresas. Adicionalmente se obtuvo un efecto positivo en la corrección de factor de potencia en una empresa y en la mejora del balance de corriente en 5. La investigación mostró la existencia de una reducción significativa de emisiones post-intervención, resaltando la efectividad de los programas.

Pulsed feedback defers cellular differentiation.

Directory of Open Access Journals (Sweden)

Joe H Levine

2012-01-01

Full Text Available Environmental signals induce diverse cellular differentiation programs. In certain systems, cells defer differentiation for extended time periods after the signal appears, proliferating through multiple rounds of cell division before committing to a new fate. How can cells set a deferral time much longer than the cell cycle? Here we study Bacillus subtilis cells that respond to sudden nutrient limitation with multiple rounds of growth and division before differentiating into spores. A well-characterized genetic circuit controls the concentration and phosphorylation of the master regulator Spo0A, which rises to a critical concentration to initiate sporulation. However, it remains unclear how this circuit enables cells to defer sporulation for multiple cell cycles. Using quantitative time-lapse fluorescence microscopy of Spo0A dynamics in individual cells, we observed pulses of Spo0A phosphorylation at a characteristic cell cycle phase. Pulse amplitudes grew systematically and cell-autonomously over multiple cell cycles leading up to sporulation. This pulse growth required a key positive feedback loop involving the sporulation kinases, without which the deferral of sporulation became ultrasensitive to kinase expression. Thus, deferral is controlled by a pulsed positive feedback loop in which kinase expression is activated by pulses of Spo0A phosphorylation. This pulsed positive feedback architecture provides a more robust mechanism for setting deferral times than constitutive kinase expression. Finally, using mathematical modeling, we show how pulsing and time delays together enable "polyphasic" positive feedback, in which different parts of a feedback loop are active at different times. Polyphasic feedback can enable more accurate tuning of long deferral times. Together, these results suggest that Bacillus subtilis uses a pulsed positive feedback loop to implement a "timer" that operates over timescales much longer than a cell cycle.

Desarrollo de un modelo de determinación de cash-flows para un proyecto de energía eólica

Directory of Open Access Journals (Sweden)

Irene Clara Pisón Fernández

2015-06-01

Full Text Available En este trabajo se analiza la problemática asociada a la producción de energía eléctrica de origen renovable, y se ofrece un modelo de definición de las variables en las que se apoya el plan de negocio de energía eólica. El plan de viabilidad muestra que los cash-flows para el accionista obtenidos en este tipo de proyectos permiten afrontar las inversiones futuras con una rentabilidad suficiente, que apunta al sector de energías renovables, y en particular al de energía eólica, como estratégico dentro de la economía española de las próximas décadas.

In-vitro model for evaluation of pulse oximetry

Science.gov (United States)

Vegfors, Magnus; Lindberg, Lars-Goeran; Lennmarken, Claes; Oberg, P. Ake

1991-06-01

An in vitro model with blood circulating in a silicon tubing system and including an artificial arterial bed is an important tool for evaluation of the pulse oximetry technique. The oxygen saturation was measured on an artificial finger using a pulse oximeter (SpO2) and on blood samples using a hemoximeter (SaO2). Measurements were performed at different blood flows and at different blood hematocrits. An increase in steady as well as in pulsatile blood flow was followed by an increase in pulse oximeter readings and a better agreement between SpO2 and SaO2 readings. After diluting the blood with normal saline (decreased hematocrit) the agreement was further improved. These results indicate that the pulse oximeter signal is related to blood hematocrit and the velocity of blood. The flow-related dependance of SpO2 was also evaluated in a human model. These results provided evidence that the pulse oximeter signal is dependent on vascular changes.

Bit rate and pulse width dependence of four-wave mixing of short optical pulses in semiconductor optical amplifiers

DEFF Research Database (Denmark)

Diez, S.; Mecozzi, A.; Mørk, Jesper

1999-01-01

We investigate the saturation properties of four-wave mixing of short optical pulses in a semiconductor optical amplifier. By varying the gain of the optical amplifier, we find a strong dependence of both conversion efficiency and signal-to-background ratio on pulse width and bit rate....... In particular, the signal-to-background ratio can be optimized for a specific amplifier gain. This behavior, which is coherently described in experiment and theory, is attributed to the dynamics of the amplified spontaneous emission, which is the main source of noise in a semiconductor optical amplifier....

Digital parallel-to-series pulse-train converter

Science.gov (United States)

Hussey, J.

1971-01-01

Circuit converts number represented as two level signal on n-bit lines to series of pulses on one of two lines, depending on sign of number. Converter accepts parallel binary input data and produces number of output pulses equal to number represented by input data.

Removal of phenol from water : a comparison of energization methods

NARCIS (Netherlands)

Grabowski, L.R.; Veldhuizen, van E.M.; Rutgers, W.R.

2005-01-01

Direct electrical energization methods for removal of persistent substances from water are under investigation in the framework of the ytriD-project. The emphasis of the first stage of the project is the energy efficiency. A comparison is made between a batch reactor with a thin layer of water and

Innovació en el procés de realització d'auditories energètiques. De l'auditoria tradicional a l'auditoria virtual

OpenAIRE

Utges Mampel, Daniel

2016-01-01

Aquest projecte planteja un nou prisma a la hora de realitzar auditories energètiques a les instal·lacions, passant d’una auditoria tradicional a una auditoria virtual, utilitzant tècniques estadístiques i la caracterització matemàtica de potencials millores d’eficiència energètica. L’auditoria virtual és un gran avenç en el sector de l’eficiència energètica, resultant en una innovació disruptiva en el sector, doncs permet reduir els costos i el temps d’entrega d’una auditoria energètica e...

Mejoras energéticas en un horno industrial de una empresa petr oquímica

OpenAIRE

Moldovan, Gabriel Ionut

2016-01-01

Treball Final de Grau en Enginyeria en Tecnologies Industrials. Codi: ET1040. Curs: 2015/2016 El problema energético mundial se resume en que nuestra bonanza social y económica, nuestra tecnología y nuestra sociedad dependen enormemente de la sobreexplotación de recursos naturales no renovables. La situación energética actual es insostenible a largo plazo y las consecuencias de seguir igual en el futuro serían devastadoras. Es necesario pues, un cambio de rumbo aunque la situa...

La energía electrica, dentro de la estructura tecnológica de la industria antioqueña

Directory of Open Access Journals (Sweden)

Gustavo López Alvarez

1991-07-01

Full Text Available En este artículo se presenta una visión general de la estructura tecnológica de la industria antioqueña en su conjunto para el periodo 1975-1987. Para el análisis se supone una función de producción en dos niveles: en el primero se emplean como insumos el capital, el trabajo, los energéticos y otras materias primas; en el segundo, los energéticos son desagregados en electricidad y otros. Usando una función translogarítmica de costos para cada uno de los niveles, se llega, finalmente, a presentar estimaciones de las elasticidades precio directas y cruzadas que darían cuenta de las relaciones económicas entre los insumos. Examinando los resultados de las estimaciones se observa que las elasticidades directas son todas negativas, el capital y los insumos energéticos son sustitutivos, mientras que la única complementariedad se presenta entre el trabajo y los insumos energéticos.

Optimising the separation of quartz and feldspar optically stimulated luminescence using pulsed excitation

International Nuclear Information System (INIS)

Ankjaergaard, C.; Jain, M.; Thomsen, K.J.; Murray, A.S.

2010-01-01

In luminescence dating, the two most commonly used natural minerals, quartz and feldspar, are exposed to different dose rates in the natural environment, and so record different doses. The luminescence signals also have different stabilities. For accurate dosimetry, the signals from these two minerals must be separated, either by physical separation of the mineral grains, or by instrumental separation of the luminescence signals. The luminescence signals from quartz and feldspar have different luminescence lifetimes under pulsed optical stimulation. This difference in lifetime can be used to discriminate between the two signals from a mixed quartz-feldspar sample. The purpose of this study is to identify optimum measurement conditions for the best separation of quartz OSL from that of feldspar in a mixed sample using pulsed stimulation and time-resolved OSL. We integrate the signal from 5 μs after the LEDs are switched off until just before the LEDs are switched on again, with the pulse on-time equal to the pulse off-time of 50 μs. By using only the initial interval of the pulsed OSL decay curve (equivalent to 0.2 s of CW-OSL using blue light at 50 mW cm -2 ) we find that the quartz to feldspar pulsed OSL intensity ratio is at a maximum. By using these parameters with an additional infrared (IR) stimulation at 175 o C before measurement (to further reduce the feldspar signal intensity), we obtain a factor of 25 enhancement in signal separation compared to that from a conventional prior-IR CW measurement. This ratio can be further improved if the counting window in the pulse off-time is restricted to detect between 20 and 50 μs instead of the entire off-period.

La imagen electrónica de la energía. Estudio estético y funcional de las páginas webs de las compañías del sector energético

OpenAIRE

Álvarez Ruiz, Antón; Reyes Moreno, María Isabel

2011-01-01

Este artículo analiza las páginas webs de las principales compañías operantes en el sector de la energía (electricidad y gas) de los países más desarrollados. La situación actual del mercado es muy significativa. Por primera vez en la historia, las administraciones centrales de estos países han consentido liberalizar el mercado energético. Y, aunque este proceso avanza con gran lentitud, comienzan a notarse cambios que anticipan un proceso de concentración, a través de compras, fusiones y ...

Sampling system for fast single pulses; Realisation d'un dispositif d'echantillonnage d'un signal bref unique

Energy Technology Data Exchange (ETDEWEB)

Zenatti, D. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1969-07-01

Development of a device for the enlargement of the domain of application of classical oscilloscopes to the observation of fast single pulses by application of the sampling principle. Its principal characteristics are: Bandwidth of 700 MHz; Maximum sensibility of 50 mV; Maximum amplitude of input signal of {+-} 1 V; Number of samples of 16; Samples separation of 0,2 ns. (author) [French] Realisation d'un dispositif permettant d'elargir le domaine d'utilisation des oscilloscopes classiques en appliquant le principe de l'echantillonnage a l'observation d'un signal bref unique. Les principales caracteristiques sont les suivantes: Bande passante de 700 MHz; Sensibilite maximale de 50 mV; Amplitude maximale du signal a echantillonner de {+-} 1 V; Nombre de points d'echantillonnage de 16; Pas d'echantillonnage de 0,2 ns. (auteur)

Particle energization by inertial Alfven wave in auroral ionosphere

Science.gov (United States)

Kumar, S.

2017-12-01

The role of inertial Alfven wave in auroral acceleration region and in the inertial regime to energize the plasma particles is an interesting field and widely discussed observationally as well as theoretically in recent years. In this work, we present the density perturbations by inertial Alfvén wave (AW) in the auroral ionosphere. We obtain dynamical equations for inertial AW and fast mode of AW using two-fluid model and then solve them numerically in order to analyze the localized structures and cavity formation. The ponderomotive force due to the high frequency inertial AW changes the background density and is believed to be responsible for the wave localization or for the formation of density cavities in auroral ionosphere. These density cavities are believed to be the sites for particle energization. This perturbed density channel grow with time until the modulation instability acquires steady state. We find that the density cavities are accompanied by the high amplitude magnetic fields. The amplitude of the strongest density cavity is estimated as ˜ 0.26n0 (n0 is unperturbed plasma number density). The results presented here are found consistent with the observational studies using FAST spacecraft.

Sync transmission method and apparatus for high frequency pulsed neutron spectral analysis systems

International Nuclear Information System (INIS)

Culver, R.B.

1981-01-01

An improved synchronization system was developed for high-frequency pulsed-neutron gamma ray well-logging which extends the upper limit of the usable source pulsing frequency. A clock is used to pulse the neutron generator at a given frequency and a scaler generates scaled-down sync pulses at a lower frequency. Radiation from the formations surrounding the borehole is detected and electrical signals related functionally to the radiation are generated. The scaled-down sync pulses and electrical signals are transmitted to the earth's surface via a seven conductor well logging cable. (DN)

Coherent combining pulse bursts in time domain

Science.gov (United States)

Galvanauskas, Almantas

2018-01-09

A beam combining and pulse stacking technique is provided that enhances laser pulse energy by coherent stacking pulse bursts (i.e. non-periodic pulsed signals) in time domain. This energy enhancement is achieved by using various configurations of Fabry-Perot, Gires-Tournois and other types of resonant cavities, so that a multiple-pulse burst incident at either a single input or multiple inputs of the system produces an output with a solitary pulse, which contains the summed energy of the incident multiple pulses from all beams. This disclosure provides a substantial improvement over conventional coherent-combining methods in that it achieves very high pulse energies using a relatively small number of combined laser systems, thus providing with orders of magnitude reduction in system size, complexity, and cost compared to current combining approaches.

Eficiencia energética y confort en edificios de oficina: El caso alemán

Directory of Open Access Journals (Sweden)

Ernesto Kuchen

2012-12-01

Full Text Available La construcción de edificios en los últimos 15 años en Europa persigue el objetivo común de dar respuesta al problema de la Eficiencia Energética y el Confort en espacios de trabajo. Las propuestas de cambio se inclinan por el desarrollo de una arquitectura “transparente”, con extensas superficies de vidrio expuestas. Dicha práctica se hace llamar ecológica y sustentable. Con el tiempo, el uso y la experiencia ponen en alerta a científicos del área. El objetivo del trabajo es detectar los aspectos más relevantes que afectan la Eficiencia Energética (EE y el Confort de espacios reales de trabajo para la elaboración apropiada de herramientas de diseño y cálculo. Para ello, se lleva a cabo un trabajo de campo en base a mediciones y encuestas en 19 edificios de oficina, en Alemania. Del monitoreo energético y del análisis del Confort se detectan potenciales de optimización. Se observa que la EE no se logra al conectar el edificio a la red energética una vez finalizada la obra arquitectónica. Por el contrario, la planificación integral, el monitoreo y el seguimiento en la vida útil del edificio permiten corregir y lograr mejores niveles de EE y Confort.

Discrimination of nuclear-explosion and lightning electromagnetic pulse

International Nuclear Information System (INIS)

Qi Shufeng; Li Ximei; Han Shaoqing; Niu Chao; Feng Jun; Liu Daizhi

2012-01-01

The discrimination of nuclear-explosion and lightning electromagnetic pulses was studied using empirical mode decomposition and the fractal analytical method. The box dimensions of nuclear-explosion and lightning electromagnetic pulses' original signals were calculated, and the box dimensions of the intrinsic mode functions (IMFs) of nuclear-explosion and lightning electromagnetic pulses' original signals after empirical mode decomposition were also obtained. The discrimination of nuclear explosion and lightning was studied using the nearest neighbor classification. The experimental results show that, the discrimination rate of the box dimension based on the first and second IMF after the original signal empirical mode decomposition is higher than that based on the third and forth IMF; the discrimination rate of the box dimension based on the original signal is higher than that based on any IMF; and the discrimination rate based on two-dimensional and three-dimensional characters is higher and more stable than that based on one-dimensional character, besides, the discrimination rate based on three-dimensional character is over 90%. (authors)

Detection of movement artifact in recorded pulse oximeter saturation.

Science.gov (United States)

Poets, C F; Stebbens, V A

1997-10-01

Movement artifact (MA) must be detected when analysing recordings of pulse oximeter saturation (SpO2). Visual analysis of individual pulse waveforms is the safest, but also the most tedious, method for this purpose. We wanted to test the reliability of a computer algorithm (Edentec Motion Annotation System), based on a comparison between pulse and heart rate, for MA detection. Ten 12-h recordings of SpO2, pulse waveforms and heart rate from ten preterm infants were analysed for the presence of MA on the pulse waveform signal. These data were used to determine the sensitivity and specificity of the computer algorithm, and of the oximeter itself, in detecting MA. Recordings were divided into segments of 2.5 s duration to compare the movement identification methods. Of the segments 31% +/- 6% (mean +/- SD) contained MA. The computer algorithm identified 95% +/- 3% of these segments, the pulse oximeter only 18% +/- 11%. Specificity was 85% +/- 4% and 99% +/- 0%, respectively. SpO2 was signal showed MA during this time, leaving a significant potential for erroneous identification of hypoxaemia. Recordings of SpO2 do not allow a reliable identification of MA. Without additional information about movement artifact, a significant proportion of recording time of pulse oximeter signal may be regarded as demonstrating hypoxaemia which, in fact, simply reflects poor measurement conditions. The computer algorithm used in this study identified periods of movement artifact reliably.

Investigation of Prevalence of Energizer Drugs and Supplements Consumption and Effective Factors Among Bodybuilder Men in Karaj (2011

Directory of Open Access Journals (Sweden)

F. Shoshtarizadeh

2013-08-01

Full Text Available Background: Body builder athletes’ high attention to form of body can result in high prevalence of nutritional disorders and habit to energizer drugs consumption. With notice to abuse problems of these drugs, this research was carried out to estimate prevalence of energizer drugs and supplements consumption in Karaj body builder men in 2011. Method: In cross-sectional (description- analytical research 780 Karaj body builder men were selected randomly. Data were collected through interview with questionnaires containing demographic questions and using information of drugs. Data were analyzed with SPSS software (Ver. 19 and κ² test with meaningful level of P<0.05. Result: Prevalence of consumption in studied sample from different types of supplements and energizer drugs was estimated 88.2%. The most consumption prevalence belonged to food supplements and vitamins group and combination of those (69.9%. About anabolic and energizer compounds and also hormonal drugs and corticosteroids, prevalence was 5.6% and 2.1% respectively and 7.7% totally. There was meaningful relation between experience times of abuse problems, place of drug and supplement supply and attention to being permissible or impermissible of those items with type of drugs or supplement (P = 0.001. Also relation between consumption of supplements and drugs with main goal in using them was meaningful (P = 0.045. Conclusion: Consumption of supplement and energizer drugs in Karaj body builder men has high prevalence.

Pick-up ion energization at the termination shock

Energy Technology Data Exchange (ETDEWEB)

Gary, S Peter [Los Alamos National Laboratory; Winske, Dan [Los Alamos National Laboratory; Wu, Pin [BOSTON UNIV.; Schwadron, N A [BOSTON UNIV.

2009-01-01

One-dimensional hybrid simulations are used to investigate how pickup ions are energized at the perpendicular termination shock. Contrary to previous models based on pickup ion energy gain by repeated crossings of the shock front (shock surfing) or due to a reforming shock front, the present simulations show that pickup ion energy gain involves a gyro-phasedependent interaction with the inhomogeneous motional electric field at the shock. The process operates at all relative concentrations of pickup ion density.

Phase measurement and control of pulsed charged beams

International Nuclear Information System (INIS)

Lewis, R.N.

1978-01-01

A method and system is described that measures and controls the arrival phase of a pulsed ion beam. The repetitive beam pulse passes through and resonantly excites a high-Q structure, tuned to the beam repetition frequency or to a higher harmonic thereof. A reference signal of the same frequency is phase-flipped from -90 0 to +90 0 at a high audio rate and also coupled to the resonator. The low-level output signal, comprised of the vector sum of the beam-induced signal and the phase-flipped reference, is amplified and processed to obtain phase information. The system is usable for beams with average currents as low as a few picoamperes and can be used in the measurement and control of pulsed beam experiments involving timing, the control of beam phase for rf particle accelerators and the nondestructive measurement of beam energy. (Auth.)

Receiver Signal to Noise Ratios for IPDA Lidars Using Sine-wave and Pulsed Laser Modulation and Direct Detections

Science.gov (United States)

Sun, Xiaoli; Abshire, James B.

2011-01-01

seeder lasers, one on-line and one offline that are intensity modulated by two different frequency sine-waves signals before being amplified by a common laser amplifier. The receiver uses narrowband amplitude demodulation, or lock-in, Signal processing at the given laser modulation frequencies [3,4]. The laser transmitter operates in a quasi CW mode with the peak power equal to twice the average power. The on-line and off-line lasers can be transmitted at the same time without interference. Another direct detection technique uses a low duty cycle pulsed laser modulation [5,6] with the laser wavelengths alternating between on-line and off-line on successive pulses. The receiver uses time resolved detection and can also provide simultaneous target range measurement. With a lower laser duty cycle it requires a much higher peak laser power for the same average power.

Modelo de innovación y optimización de la energía solar en España. La aplicación de las tecnologías disponibles para el aprovechamiento de recursos, comercialización y beneficios de la energía solar

OpenAIRE

González Peña, Daniel

2016-01-01

Tesis Doctoral leída en la Universidad Rey Juan Carlos de Madrid en 2014. Directora de la Tesis: Dra. Carmen de Pablos Heredero En esta Tesis Doctoral se pretende analizar los límites, tanto a medio como a largo plazo, de la competitividad económica de la energía solar en España, estudiando el nivel de evolución que presuntamente debería tener esta forma de producción de energía, hasta conseguir llegar a ser competitiva con las energías fósiles, y otras fuentes emergentes en desarrollo. ...

Study of {sup 14}N NQR response to SORC pulse sequence

Energy Technology Data Exchange (ETDEWEB)

Konnai, A., E-mail: konnai@nmri.go.jp; Odano, N. [National Maritime Research Institute, Department of Navigation and System Engineering (Japan); Asaji, T. [Nihon University, Department of Chemistry, College of Humanities and Sciences (Japan)

2008-01-15

The behavior of nuclear quadrupole resonance (NQR) signals between RF pulses of the strong off-resonance comb (SORC) as well as the spin-locking spin-echo (SLSE) pulse sequences was studied as for {sup 14}N NQR line {nu}{sub +} of dimethylnitramine (CH{sub 3}){sub 2}NNO{sub 2} at 77 K. The periodic variation of the signal amplitude observed by using SORC pulse sequence could be reasonably explained by the theoretical expression reported in the literature.

Digital signal processing for He3 proportional counter

International Nuclear Information System (INIS)

Ahmadov, Q.S.; Institute of Radiation Problems, ANAS, Baku

2011-01-01

Full text: Data acquisition systems for nuclear spectroscopy have traditionally been based on systems with analog shaping amplifiers followed by analog-to-digital converters. Recently, however, new systems based on digital signal processing allow us to replace the analog shaping and timing circuitry the numerical algorithms to derive properties of the pulse such as its amplitude. DSP is a fully numerical analysis of the detector pulse signals and this technique demonstrates significant advantages over analog systems in some circumstances. From a mathematical point of view, one can consider the signal evolution from the detector to the ADC as a sequence of transformations that can be described by precisely defined mathematical expressions.Digital signal processing with ADCs has the possibility to utilize further information on the signal pulses from radiation detectors [1] [2]. In the experiment each step of the signal generation in the 3He filled proportional counter was described using digital signal processing techniques (DSP). The electronic system has consisted of a detector, a preamplifier and a digital oscilloscope. The pulses from the detector were digitized using a OTSZS-02 (250USB)-4 digital storage oscilloscope from ZAO R UDNEV-SHILYAYEV . This oscilloscope allowed signal digitization with accuracy of 8 bit(256 levels) and with frequency of up to 5.10''8 samples/s. As a neutron source was used Cf-252.To obtain detector output current pulse I(t) created by the motions of the ions/electrons pairs was written an algorithm which can easily be programmed using modern computer programming languages

Climatización de vivienda a partir de energía geotérmica de baja entalpía

OpenAIRE

Alfaro del Moral, Ignacio

2015-01-01

El TFG está centrado en la energía geotérmica utilizada para la climatización de una vivienda. Se elige una vivienda a la que se desea realizar una instalación geotérmica, de modo que una vez se ha realizado un estudio de la misma, se lleva a cabo un amplio estudio de la fuente renovable (tipos de energía, tipos de yacimientos, situación de la energía geotérmica, componentes del sistema, diseño del sistema, etc.). El proyecto desemboca en la elección de los componentes geotérmicos ideales par...

Principio de la conservación de la energía mecánica en caída libre

OpenAIRE

Carmona Franco, José Edgar; Amaya Díaz, José Alexander; Salcedo Rodríguez, Karen Lizeth

2007-01-01

Para estudiar el principio de la conservación de la energía mecánica utilizamos un movimiento uniformemente acelerado como lo es la caída libre, en el cual se puede mostrar como son las interacciones entre la energía cinética Ec y la energía potencial Ep, con relación a una altura arbitraria, y así poder demostrar la veracidad de este principio en dicho movimiento, registrando el tiempo empleado por un balín entre un electroimán y en sensor acústico por un cronómetro digital. To study the...

Performance scaling via passive pulse shaping in cavity-enhanced optical parametric chirped-pulse amplification.

Science.gov (United States)

Siddiqui, Aleem M; Moses, Jeffrey; Hong, Kyung-Han; Lai, Chien-Jen; Kärtner, Franz X

2010-06-15

We show that an enhancement cavity seeded at the full repetition rate of the pump laser can automatically reshape small-signal gain across the interacting pulses in an optical parametric chirped-pulse amplifier for close-to-optimal operation, significantly increasing both the gain bandwidth and the conversion efficiency, in addition to boosting gain for high-repetition-rate amplification. Applied to a degenerate amplifier, the technique can provide an octave-spanning gain bandwidth.

The Contribution of Compressional Magnetic Pumping to the Energization of the Earth's Outer Electron Radiation Belt During High-Speed Stream-Driven Storms

Science.gov (United States)

Borovsky, Joseph E.; Horne, Richard B.; Meredith, Nigel P.

2017-12-01

Compressional magnetic pumping is an interaction between cyclic magnetic compressions and pitch angle scattering with the scattering acting as a catalyst to allow the cyclic compressions to energize particles. Compressional magnetic pumping of the outer electron radiation belt at geosynchronous orbit in the dayside magnetosphere is analyzed by means of computer simulations, wherein solar wind compressions of the dayside magnetosphere energize electrons with electron pitch angle scattering by chorus waves and by electromagnetic ion cyclotron (EMIC) waves. The magnetic pumping is found to produce a weak bulk heating of the electron radiation belt, and it also produces an energetic tail on the electron energy distribution. The amount of energization depends on the robustness of the solar wind compressions and on the amplitude of the chorus and/or EMIC waves. Chorus-catalyzed pumping is better at energizing medium-energy (50-200 keV) electrons than it is at energizing higher-energy electrons; at high energies (500 keV-2 MeV) EMIC-catalyzed pumping is a stronger energizer. The magnetic pumping simulation results are compared with energy diffusion calculations for chorus waves in the dayside magnetosphere; in general, compressional magnetic pumping is found to be weaker at accelerating electrons than is chorus-driven energy diffusion. In circumstances when solar wind compressions are robust and when EMIC waves are present in the dayside magnetosphere without the presence of chorus, EMIC-catalyzed magnetic pumping could be the dominant energization mechanism in the dayside magnetosphere, but at such times loss cone losses will be strong.

A ingestão energética de pacientes em hemodiálise é subrelatada?

Directory of Open Access Journals (Sweden)

Inaiana Marques Filizola Vaz

2015-09-01

Full Text Available ResumoIntrodução:O sub-relato da ingestão energética é pouco estudado na população em hemodiálise.Objetivo:Avaliar o sub-relato da ingestão energética e os fatores associados em pacientes em hemodiálise.Métodos:Estudo transversal, com 344 pacientes adultos estáveis, de dez centros de hemodiálise de Goiânia-GO. A ingestão energética foi avaliada por seis recordatórios de 24 horas e a taxa de metabolismo basal (TMB foi calculada pela equação de Harris Benedict. Foi considerado como sub-relato quando a razão entre a ingestão energética média e a TMB foi menor que 1,27. Para análise dos fatores associados ao sub-relato, foi utilizada a regressão de Poisson com estimativa robusta da variância.Resultados:A prevalência de sub-relato foi de 65,7%, sendo mais expressiva em indivíduos com excesso de peso e nos dias sem diálise. O resultado final da análise multivariada identificou quatro fatores independentemente associados ao sub-relato: sexo feminino (RP = 1,27; IC = 1,10-1,46, índice de massa corporal ≥ 25 kg/m2 (RP = 1,29; IC = 1,12-1,48, três ou menos refeições/dia (RP = 1,31; IC = 1,14-1,51 e tempo de hemodiálise inferior a cinco anos (RP = 1,19; IC = 1,01-1,40.Conclusão:A população avaliada demonstrou elevada prevalência de sub-relato da ingestão energética. Pertencer ao sexo feminino, apresentar excesso de peso, fazer um menor número de refeições diárias e ter menos tempo de hemodiálise foram fatores associados ao sub-relato.

A digital long pulse integrator

International Nuclear Information System (INIS)

Broesch, J.D.; Strait, E.J.; Snider, R.T.

1996-10-01

A prototype digital integrator with very long integration capabilities has been developed and field tested on an inductive magnetic sensor on the DIII-D Tokamak. The integrator is being developed for use on ITER with a pulse length of 1000 s, and has direct applications for other long pulse Tokamaks. Inductive magnetic sensors are routinely used on existing Tokamaks, are well understood, and are extremely robust, however, they require integration of the signal to determine the magnetic field strength. The next generation of Tokamaks, will have pulse lengths of 1000 s or longer, require integrators with drift and noise characteristics compatible with the very long pulse lengths. This paper will discuss the architecture, algorithms, and programming of the Long Pulse Integrator (LPI). Of particular interest are the noise control and the built-in offset correction techniques used in this application

Optimization of Contrast-to-Tissue Ratio by Adaptation of Transmitted Ternary Signal in Ultrasound Pulse Inversion Imaging

Directory of Open Access Journals (Sweden)

Sébastien Ménigot

2013-01-01

Full Text Available Ultrasound contrast imaging has provided more accurate medical diagnoses thanks to the development of innovating modalities like the pulse inversion imaging. However, this latter modality that improves the contrast-to-tissue ratio (CTR is not optimal, since the frequency is manually chosen jointly with the probe. However, an optimal choice of this command is possible, but it requires precise information about the transducer and the medium which can be experimentally difficult to obtain, even inaccessible. It turns out that the optimization can become more complex by taking into account the kind of generators, since the generators of electrical signals in a conventional ultrasound scanner can be unipolar, bipolar, or tripolar. Our aim was to seek the ternary command which maximized the CTR. By combining a genetic algorithm and a closed loop, the system automatically proposed the optimal ternary command. In simulation, the gain compared with the usual ternary signal could reach about 3.9 dB. Another interesting finding was that, in contrast to what is generally accepted, the optimal command was not a fixed-frequency signal but had harmonic components.

Observation of meander pattern in signals from superconducting MgB{sub 2} detector by scanning pulsed laser imaging

Energy Technology Data Exchange (ETDEWEB)

Ishida, Takekazu, E-mail: ishida@center.osakafu-u.ac.jp [Department of Physics and Electronics, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan); Institute for Nanofabrication Research, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan); Yagi, Ikutaro; Yoshioka, Naohito; Huy, Ho Thanh [Department of Physics and Electronics, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan); Yotsuya, Tsutomu [Institute for Nanofabrication Research, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan); Nanoscience and Nanotechnology Research Center, Osaka Prefecture University, 2-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8570 (Japan); Shimakage, Hisashi [Department of Electrical and Electronic Engineering, College of Engineering, 4-12-1, Nakanarusawa, Hitachi, Ibaraki 316-8511 (Japan); Miki, Shigehito [Kansai Advanced Research Center, National Institute of Information and Communications Technology, 588-2 Iwaoka-cho, Nishi-ku, Kobe, Hyogo 651-2429 (Japan); Wang, Zhen [Institute for Nanofabrication Research, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan); Kansai Advanced Research Center, National Institute of Information and Communications Technology, 588-2 Iwaoka-cho, Nishi-ku, Kobe, Hyogo 651-2429 (Japan)

2013-01-15

Highlights: ► We fabricate a superconducting MgB{sub 2} meander detector as a solid-state neutron detector. ► MgB{sub 2} detector uses XYZ stage, optical fiber and focused lens to scan as a microscope. ► The 6 μm line-and-space in meandering pattern can be resolved in signals against pulsed laser. -- Abstract: Superconducting MgB{sub 2} meander detector has been imaged by scanning a spot of 1.5-μm focused pulsed laser. The superconducting detector using high-quality {sup 10}B-enriched MgB{sub 2} thin films at higher operating temperatures has been fabricated to utilize a resistance change induced by the nuclear energy of {sup 10}B and neutron. The MgB{sub 2} detector consists of a 200-nm-thick MgB{sub 2} thin-film meander line, a 300-nm-thick SiO protective layer, and 150-nm-thick Nb electrodes with 1-μm MgB{sub 2} wires. The devices were placed in a 4 K refrigerator to control at a certain temperature below T{sub c}. A scanning laser spot can be used by the combination of the XYZ piezo-drive stage and an optical fibre with an aspheric focused lens. The measurement system is fully controlled by LabVIEW based software. We succeeded in observing a line-and-space image of a meandering pattern by analysing response signals.

Instalación eléctrica de una vivienda unifamiliar aislada mediante suministro de energías renovables

OpenAIRE

LOZANO VALLADOLID, FERNANDO

2015-01-01

[ES] Instalación eléctrica con grado de electrificación elevada de una vivienda unifamiliar aislada mediante suministro de energías renovables (solar, eólica, geotérmicas). Lozano Valladolid, F. (2015). Instalación eléctrica de una vivienda unifamiliar aislada mediante suministro de energías renovables. http://hdl.handle.net/10251/58751. TFGM

Pulsed ultrasound modulated optical tomography with harmonic lock-in holography detection.

Science.gov (United States)

Ruan, Haowen; Mather, Melissa L; Morgan, Stephen P

2013-07-01

A method that uses digital heterodyne holography reconstruction to extract scattered light modulated by a single-cycle ultrasound (US) burst is demonstrated and analyzed. An US burst is used to shift the pulsed laser frequency by a series of discrete harmonic frequencies which are then locked on a CCD. The analysis demonstrates that the unmodulated light's contribution to the detected signal can be canceled by appropriate selection of the pulse repetition frequency. It is also shown that the modulated signal can be maximized by selecting a pulse sequence which consists of a pulse followed by its inverted counterpart. The system is used to image a 12 mm thick chicken breast with 2 mm wide optically absorbing objects embedded at the midplane. Furthermore, the method can be revised to detect the nonlinear US modulated signal by locking at the second harmonic US frequency.

Optimización de variables energéticas en función de la productividad y competitividad de la industria láctea y caracterización energética y tecnológica del sector

OpenAIRE

Bolaños Bolaños, Carlos Alberto

2014-01-01

Debido a la competitividad del mercado y a la incertidumbre de los empresarios industriales por la sostenibilidad de las empresas manufactureras en Colombia, la eficiencia energética se convierte en una de las herramientas principales para el progreso y el no estancamiento de su desarrollo tecnológico y económico. Por ello se debe incentivar a los empresarios para la búsqueda de soluciones y alternativas que giren en torno a la eficiencia energética de sus procesos. Algunas de ellas se desarr...

Randomized, controlled clinical trial evaluating the efficacy of pulsed signal therapy in dogs with osteoarthritis.

Science.gov (United States)

Sullivan, Meghan O; Gordon-Evans, Wanda J; Knap, Kim E; Evans, Richard B

2013-04-01

To evaluate the efficacy of pulsed signal therapy (PST) in reducing pain and increasing function in dogs with osteoarthritis (OA) using a randomized, blinded, controlled clinical trial. Randomized, controlled, blinded clinical trial. Adult dogs (n = 60) with moderate-to-severe clinical signs of OA. Dogs were randomized by age into 2 groups: dogs ≥ 9 years and dogs Goniometry and gait analysis were performed, and the Canine Brief Pain Inventory (CBPI) questionnaire was given to the owners to fill out without supervision. Outcome measures were repeated at the end of treatment (Day 11) and 6 weeks after beginning treatment (Day 42). The PST group performed significantly better than the control group as measured by the CBPI Severity and Interference scores (P Veterinary Surgeons.

Estudio del aprovechamiento energético de los puntos de regulación de presión en la red de abastecimiento a Cartagena

OpenAIRE

Vera Morales, Carlos

2015-01-01

El actual sistema energético a nivel mundial está basado en la generación de energía a partir de combustibles fósiles como el petróleo, el carbón mineral y el gas. En la actualidad, la generación de energía a partir de estas materias primas se está replanteando por razones como la limitada disponibilidad de recursos. La Unión Europea tiene como objetivo prioritario la promoción de la electricidad generada a partir de fuentes de energía renovables. Esto se debe a razones dive...

Generation of short electrical pulses based on bipolar transistorsny

Directory of Open Access Journals (Sweden)

M. Gerding

2004-01-01

Full Text Available A system for the generation of short electrical pulses based on the minority carrier charge storage and the step recovery effect of bipolar transistors is presented. Electrical pulses of about 90 ps up to 800 ps duration are generated with a maximum amplitude of approximately 7V at 50Ω. The bipolar transistor is driven into saturation and the base-collector and base-emitter junctions become forward biased. The resulting fast switch-off edge of the transistor’s output signal is the basis for the pulse generation. The fast switching of the transistor occurs as a result of the minority carriers that have been injected and stored across the base-collector junction under forward bias conditions. If the saturated transistor is suddenly reverse biased the pn-junction will appear as a low impedance until the stored charge is depleted. Then the impedance will suddenly increase to its normal high value and the flow of current through the junction will turn to zero, abruptly. A differentiation of the output signal of the transistor results in two short pulses with opposite polarities. The differentiating circuit is implemented by a transmission line network, which mainly acts as a high pass filter. Both the transistor technology (pnp or npn and the phase of the transfer function of the differentating circuit influence the polarity of the output pulses. The pulse duration depends on the transistor parameters as well as on the transfer function of the pulse shaping network. This way of generating short electrical pulses is a new alternative for conventional comb generators based on steprecovery diodes (SRD. Due to the three-terminal structure of the transistor the isolation problem between the input and the output signal of the transistor network is drastically simplified. Furthermore the transistor is an active element in contrast to a SRD, so that its current gain can be used to minimize the power of the driving signal.

Pulsed transport critical currents of Bi2212 tapes in pulsed magnetic fields

Energy Technology Data Exchange (ETDEWEB)

Rogacki, K [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, Wroclaw (Poland); Gilewski, A; Klamut, J [International Laboratory of High Magnetic Fields and Low Temperatures, Polish Academy of Sciences, Wroclaw (Poland); Newson, M; Jones, H [Clarendon Laboratory, University of Oxford, Oxford (United Kingdom); Glowacki, B A [IRC in Superconductivity and Department of Materials Science, University of Cambridge, Cambridge (United Kingdom)

2002-07-01

If high-T{sub C} superconductors are ever to be used in high-field applications, it is vital that the critical surfaces can be mapped under high-field conditions. However, the latest superconductors have high currents even at fields over 20 T, making accurate measurements very difficult due to the thermal and mechanical problems. In this paper, we compare measurements on BSCCO-2212 tape using a number of different methods, particularly an innovative pulsed transport current and pulsed field mode. We show how the analysis of the voltage signal from BSCCO-2212 tape in pulsed conditions may be used to extract the critical current in quasi-stationary conditions. The effect of a metallic substrate on the results is also briefly discussed. (author)

Producción de A.C.S. y climatización de una vivienda unifamiliar con energía geotérmica

OpenAIRE

Martínez Doce, Rubén

2014-01-01

El objetivo de este proyecto fin de carrera es el de realizar un diseño de una instalación para la producción de agua caliente sanitaria (A.C.S.), climatización de las estancias y de una piscina cubierta, de una vivienda unifamiliar mediante energía geotérmica, con el fin de proporcionar un ahorro energético utilizando una energía limpia. Ingeniería Industrial Industria Ingeniaritza

Propuesta de mejora energética para una planta de producción de clinker

Directory of Open Access Journals (Sweden)

Leonardo Rodriguez Urrego

2017-11-01

Full Text Available El siguiente trabajo presenta un análisis de la eficiencia energética en la industria cementera y un ejemplo real en donde se proponen mejoras para disminuir considerablemente el consumo energético. El aumento de la eficiencia disminuye considerablemente el costo de la energía eléctrica, además de las emisiones de CO2 ayudando así al mantenimiento y la preservación del medio ambiente. El caso de estudio fue aplicado en la planta de producción de cemento de san Vicente del Raspeig operada por CEMEX en España. En este caso se analizó una sección de la planta de producción, donde se realiza la molienda y el ensacado de cemento. Se encontró que, al implementar las mejoras propuestas, el costo de producción disminuye y el punto de equilibrio con respecto a la implementación de estos nuevos equipos no era mayor a 5 años lo cual hace que estas mejoras sean factibles.

Pulse radiolysis based on a femtosecond electron beam and a femtosecond laser light with double-pulse injection technique

International Nuclear Information System (INIS)

Yang Jinfeng; Kondoh, Takafumi; Kozawa, Takahiro; Yoshida, Youichi; Tagawa, Seiichi

2006-01-01

A new pulse radiolysis system based on a femtosecond electron beam and a femtosecond laser light with oblique double-pulse injection was developed for studying ultrafast chemical kinetics and primary processes of radiation chemistry. The time resolution of 5.2 ps was obtained by measuring transient absorption kinetics of hydrated electrons in water. The optical density of hydrated electrons was measured as a function of the electron charge. The data indicate that the double-laser-pulse injection technique was a powerful tool for observing the transient absorptions with a good signal to noise ratio in pulse radiolysis

ENERGÍA DE BAJA INTENSIDAD: gobiernos, mercados e instituciones en el regionalismo energético de América del Sur

Directory of Open Access Journals (Sweden)

Stefano Palestini

Full Text Available A pesar de haber sido considerada un área prioritaria de cooperación, el regionalismo energético sudamericano muestra signos de estancamiento, evidenciados por las infructuosas negociaciones de un Tratado Energético Sudamericano. Este artículo explica la paradoja de por qué, no obstante la voluntad política, las favorables condiciones estructurales para la integración, y la creación de instituciones regionales ad hoc, el regionalismo energético no consiguió pasar de las declaraciones intergubernamentales a la implementación de políticas. Se argumenta que ninguna de las instituciones creadas ha sido capaz de mediar la divergencia entre mercados y entre preferencias gubernamentales. Se requiere por tanto de un nuevo consenso que replantee la necesidad y la capacidad de la región para llevar adelante la agenda de integración energética. A un nivel más general, el caso del sector energético brinda lecciones importantes acerca de los desafíos futuros que enfrenta la cooperación regional en materia de políticas públicas en Sudamérica.

Por uma nova ordem energética global? potencialidades e perspectivas da questão energética entre os países BRICS Towards a new world energy order? potentialities and perspectives of the energy issue between the BRICS countries

Directory of Open Access Journals (Sweden)

José María Gómez

2012-12-01

Full Text Available O presente artigo propõe analisar a questão energética entre os BRICS e o potencial de rearticulação da ordem energética global que dela emerge. Para tal, realiza três movimentos. Em primeiro lugar, investiga o crescente impacto agregado dos países BRICS no cenário energético global, com vistas a analisar seu avanço em uma temática até então reduto dos países desenvolvidos. Em segundo lugar, aborda a matriz energética de cada um dos cinco países do ponto de vista de suas economias políticas e da questão da sustentabilidade. Em terceiro lugar, e com base na seção anterior, propõe mapear as áreas de conflito e de possível aproximação entre os BRICS, na tentativa de localizar as possibilidades e limites da sua cooperação energética. Com base nessa investigação, conclui que, diante das potencialidades para a cooperação entre os países, a organização de suas ofertas e demandas energéticas nacionais pode permitir ao agrupamento articular-se como um novo polo no cenário energético global.The article analyzes energy-related issues among the BRICS countries and the potential refashioning of the world energy order that might spring from them. It begins by investigating the growing impact of the BRICS countries within the international order, with the intention of tracking their progress in an ambit so far restricted to developed countries and their oil suppliers. The text subsequently analyzes the energy matrix of each of the five BRICS countries from the points of view of political economy and sustainability. Finally, based on the previous sections, the final section of the article maps the tensions and complementarities between the BRICS and outlines the possibilities and limits of their cooperation on energy issues. The analysis concludes that given the potential for energy-related cooperation between these countries, a clear definition of their national energy supply and demand may allow the grouping to position

Caracterización financiera de las empresas generadoras de energía colombianas (2005–2012

Directory of Open Access Journals (Sweden)

Amanda Lucía Restrepo Londoño

2016-01-01

Full Text Available El presente documento tiene como objetivo principal la caracterización desde el punto de vista financiero de las empresas de generación más representativas que transaron en bolsa entre los años 2005 a 2012. La generación de energía en Colombia se encuentra concentrada en cinco empresas de acuerdo con volúmenes de generación y ventas en los mercados regulado y no regulado. Estas empresas se caracterizaron a partir del análisis de indicadores financieros y correlaciones entre ellos, la demanda de energía y la entrada en operación de centrales de generación. Como resultado se evidencia la relación directa de la demanda de energía en el crecimiento de ingresos operacionales, inversiones en Propiedad, Planta y Equipo e indicadores financieros, además de una estructura financiera representada en activos fijos y financiación de largo plazo.

Conversión química y biológica de la energía luminosa fotoproducción de peroxido de hidrógeno

OpenAIRE

Roncel Gil, Mercedes

1988-01-01

Todas las formas de vida hasta ahora conocidas en nuestro planeta requieren energía para su crecimiento y conservación. Las plantas superiores y algunos tipos de algas y bacterias obtienen energía directamente de la radiación solar, que utilizan para sintetizar aquel las sustancias esenciales para su propio conocimiento y desarrollo. Los animales, en cambio, no pueden utilizar la luz solar como fuente de energía y satisfacen sus requerimientos energéticos alimentándose de plantas u otros anim...

Ahorro energético mediante estrategias de iluminación natural optimizadas

Directory of Open Access Journals (Sweden)

Puigdomènech Franquesa, Joan

1986-04-01

Full Text Available Electrical charges in buildings and specially in those of commercial use, can be diminished by means of natural lighting strategies. Taking the climate features of our country into consideration, it is necessary to prevent the inconveniences caused by an en erg y excess in summer, so solar Controls are needed. The only practical way to achieve the suitable balance between thermal and light needs, so as to get a monthly or annual energetic balance optimization, is to operate with the computer. A programme with such characteristics is described here. Its application gives important sarings in non renouvable energy savings.Mediante estrategias de iluminación natural es posible disminuir las cargas eléctricas de los edificios y en especial los de uso comercial. Dadas las características climáticas de nuestro país es necesario prever los inconvenientes de un exceso de energía en verano, para lo cual es preciso disponer de controles solares. Encontrar el correcto equilibrio entre las necesidades térmicas y lumínicas en base a la optimización del balance energético mensual o anual es únicamente factible mediante el uso del ordenador. Un programa que responde a estas características es descrito en el presente trabajo, obteniéndose con su aplicación importantes ahorros en el consumo de energías no renovables.

Evaluation of dynamic range for LLNL streak cameras using high contrast pulsed and pulse podiatry on the Nova laser system

International Nuclear Information System (INIS)

Richards, J.B.; Weiland, T.L.; Prior, J.A.

1990-01-01

This paper reports on a standard LLNL streak camera that has been used to analyze high contrast pulses on the Nova laser facility. These pulses have a plateau at their leading edge (foot) with an amplitude which is approximately 1% of the maximum pulse height. Relying on other features of the pulses and on signal multiplexing, we were able to determine how accurately the foot amplitude was being represented by the camera. Results indicate that the useful single channel dynamic range of the instrument approaches 100:1

Detection capability of a pulsed Ground Penetrating Radar utilizing an oscilloscope and Radargram Fusion Approach for optimal signal quality

Science.gov (United States)

Seyfried, Daniel; Schoebel, Joerg

2015-07-01

In scientific research pulsed radars often employ a digital oscilloscope as sampling unit. The sensitivity of an oscilloscope is determined in general by means of the number of digits of its analog-to-digital converter and the selected full scale vertical setting, i.e., the maximal voltage range displayed. Furthermore oversampling or averaging of the input signal may increase the effective number of digits, hence the sensitivity. Especially for Ground Penetrating Radar applications high sensitivity of the radar system is demanded since reflection amplitudes of buried objects are strongly attenuated in ground. Hence, in order to achieve high detection capability this parameter is one of the most crucial ones. In this paper we analyze the detection capability of our pulsed radar system utilizing a Rohde & Schwarz RTO 1024 oscilloscope as sampling unit for Ground Penetrating Radar applications, such as detection of pipes and cables in the ground. Also effects of averaging and low-noise amplification of the received signal prior to sampling are investigated by means of an appropriate laboratory setup. To underline our findings we then present real-world radar measurements performed on our GPR test site, where we have buried pipes and cables of different types and materials in different depths. The results illustrate the requirement for proper choice of the settings of the oscilloscope for optimal data recording. However, as we show, displaying both strong signal contributions due to e.g., antenna cross-talk and direct ground bounce reflection as well as weak reflections from objects buried deeper in ground requires opposing trends for the oscilloscope's settings. We therefore present our Radargram Fusion Approach. By means of this approach multiple radargrams recorded in parallel, each with an individual optimized setting for a certain type of contribution, can be fused in an appropriate way in order to finally achieve a single radargram which displays all

Estrategia de control de modelo predictivo para el despacho y almacenamiento de energía renovable en sistemas híbridos

OpenAIRE

Rosero Beltrán, Jorge Luis

2012-01-01

Actualmente la energía eléctrica es generada por fuentes que consumen combustibles fósiles y/o energía nuclear, con los consecuentes riesgos y da~nos al medio ambiente que esto representa. El aumento en los precios internacionales del petróleo y su inevitable agotamiento,la demanda de grandes cantidades de energía y el envejecimiento de las redes actuales, han hecho que en los últimos años se de un importante impulso y desarrollo a la generación de electricidad basada en fuentes renovables...

Using Pulse Width Modulation for Wireless Transmission of Neural Signals in Multichannel Neural Recording Systems

Science.gov (United States)

Yin, Ming; Ghovanloo, Maysam

2013-01-01

We have used a well-known technique in wireless communication, pulse width modulation (PWM) of time division multiplexed (TDM) signals, within the architecture of a novel wireless integrated neural recording (WINeR) system. We have evaluated the performance of the PWM-based architecture and indicated its accuracy and potential sources of error through detailed theoretical analysis, simulations, and measurements on a setup consisting of a 15-channel WINeR prototype as the transmitter and two types of receivers; an Agilent 89600 vector signal analyzer and a custom wideband receiver, with 36 and 75 MHz of maximum bandwidth, respectively. Furthermore, we present simulation results from a realistic MATLAB-Simulink model of the entire WINeR system to observe the system behavior in response to changes in various parameters. We have concluded that the 15-ch WINeR prototype, which is fabricated in a 0.5-μm standard CMOS process and consumes 4.5 mW from ±1.5 V supplies, can acquire and wirelessly transmit up to 320 k-samples/s to a 75-MHz receiver with 8.4 bits of resolution, which is equivalent to a wireless data rate of ~ 2.26 Mb/s. PMID:19497823

HPGe detectors timing using pulse shape analysis techniques

International Nuclear Information System (INIS)

Crespi, F.C.L.; Vandone, V.; Brambilla, S.; Camera, F.; Million, B.; Riboldi, S.; Wieland, O.

2010-01-01

In this work the Pulse Shape Analysis has been used to improve the time resolution of High Purity Germanium (HPGe) detectors. A set of time aligned signals was acquired in a coincidence measurement using a coaxial HPGe and a cerium-doped lanthanum chloride (LaCl 3 :Ce) scintillation detector. The analysis using a Constant Fraction Discriminator (CFD) time output versus the HPGe signal shape shows that time resolution ranges from 2 to 12 ns depending on the slope in the initial part of the signal. An optimization procedure of the CFD parameters gives the same final time resolution (8 ns) as the one achieved after a correction of the CFD output based on the current pulse maximum position. Finally, an algorithm based on Pulse Shape Analysis was applied to the experimental data and a time resolution between 3 and 4 ns was obtained, corresponding to a 50% improvement as compared with that given by standard CFDs.

Importancia energética y ambiental de la Biomasa en Colombia

Directory of Open Access Journals (Sweden)

Hernández Luis Alfredo

1994-12-01

Full Text Available

Entiéndase por energía de la biomasa aquélla que se origina al procesar parcial o totalmente cualquier sustancia o materia originada a través del proceso de fotosíntesis de los vegetales. Luego comprende especies y microespecies que cumplen para el hombre y el ecosistema una función especial ligada a factores climáticos, geomorfológicos y socioeconómicos. Antes de la aparición de los combustibles fósiles (otra forma concentrada de biomasa y de la electricidad, la biomasa constituía la principal oferta energética para el desarrollo y sobrevivencia del hombre. Si se tiene en cuenta que en el proceso de alimentación humana, el hombre y los animales utilizan menos del10% de la biomasa producida, queda un sobrante en estado sólido o en suspensión y que, por sus grandes volúmenes, genera problemas de contaminación en el campo y la ciudad, por ejemplo, basuras, residuos de plazas de mercado, pulpa de café, residuos de matadero, de procesamiento de vegetales, lácteos, y licoreras, residuos domésticos y residuos animales entre otros. Para el procesamiento o aprovechamiento de estos residuos existen tecnologías que buscan incorporarlos, en términos de materia y/o energía, a los procesos energéticos y agrícolas, captando de ellos, principalmente los valiosos elementos que los originaron. Dentro de estas tecnolog

FPGA-based design and implementation of arterial pulse wave generator using piecewise Gaussian-cosine fitting.

Science.gov (United States)

Wang, Lu; Xu, Lisheng; Zhao, Dazhe; Yao, Yang; Song, Dan

2015-04-01

Because arterial pulse waves contain vital information related to the condition of the cardiovascular system, considerable attention has been devoted to the study of pulse waves in recent years. Accurate acquisition is essential to investigate arterial pulse waves. However, at the stage of developing equipment for acquiring and analyzing arterial pulse waves, specific pulse signals may be unavailable for debugging and evaluating the system under development. To produce test signals that reflect specific physiological conditions, in this paper, an arterial pulse wave generator has been designed and implemented using a field programmable gate array (FPGA), which can produce the desired pulse waves according to the feature points set by users. To reconstruct a periodic pulse wave from the given feature points, a method known as piecewise Gaussian-cosine fitting is also proposed in this paper. Using a test database that contains four types of typical pulse waves with each type containing 25 pulse wave signals, the maximum residual error of each sampling point of the fitted pulse wave in comparison with the real pulse wave is within 8%. In addition, the function for adding baseline drift and three types of noises is integrated into the developed system because the baseline occasionally wanders, and noise needs to be added for testing the performance of the designed circuits and the analysis algorithms. The proposed arterial pulse wave generator can be considered as a special signal generator with a simple structure, low cost and compact size, which can also provide flexible solutions for many other related research purposes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Estudio energético en el taller de chapistería en Volkswagen Navarra S.A.

OpenAIRE

Echavarren Sarasibar, Sergio

2016-01-01

El presente proyecto se ha desarrollado con el objetivo de obtener la titualción de Grado en Tecnología Indistriales de la Univerisdad Pública de Navarra. El proyecto recoge un descripción detallada de las instalaciones de aire comprimido en taller de Chapisteria, una documentación de consumos, equipos, instalaciones con el objetivo de detectar derroches energéticos en la instalación. Con dichos derroches se ha realizado medidas de ahorro que reducen el gasto energético d...

Proyecto Energético Palmdale; Decisión del Permiso Final

Science.gov (United States)

Proyecto Energético Palmdale: EPA Región 9 por el presente emite aviso de su decisión final, el cumplimiento con la Ley Federal de Aire Limpio, para la construcción de una planta generadora de electricidad de ciclo combinado y alimentada por gas natural

Sandia Pulsed Reactor Facility (SPRF) calculator-assisted pulse analysis and display system

International Nuclear Information System (INIS)

Estes, B.F.; Berry, D.T.

1980-02-01

Two solid-metal fast burst type reactors (SPR II and SPR III) are operated at the Sandia Pulsed Reactor Facility. Since startup of the reactors, oscilloscope traces have been used to record (by camera) the pulse (power) shape while log N systems have measured initial reactor period. Virtually no other pulse information is available. A decision was made to build a system that could collect the basic input data available from the reactor - fission chambers, photodiodes, and thermocouples - condition the signals and output the various parameters such as power, energy, temperature, period and lifetime on hard copy that would provide a record for operations personnel as well as the experimenter. Because the reactors operate in short time frames - pulse operation - it is convenient to utilize the classical Nordheim-Fuchs approximation of the diffusion equation to describe reactor behavior. This report describes the work performed to date in developing the calculator system and analytical models for computing the desired parameters

Low-intensity pulsed ultrasound accelerates tooth movement via activation of the BMP-2 signaling pathway.

Directory of Open Access Journals (Sweden)

Hui Xue

Full Text Available The present study was designed to determine the underlying mechanism of low-intensity pulsed ultrasound (LIPUS induced alveolar bone remodeling and the role of BMP-2 expression in a rat orthodontic tooth movement model. Orthodontic appliances were placed between the homonymy upper first molars and the upper central incisors in rats under general anesthesia, followed by daily 20-min LIPUS or sham LIPUS treatment beginning at day 0. Tooth movement distances and molecular changes were evaluated at each observation point. In vitro and in vivo studies were conducted to detect HGF (Hepatocyte growth factor/Runx2/BMP-2 signaling pathways and receptor activator of NFκB ligand (RANKL expression by quantitative real time PCR (qRT-PCR, Western blot and immunohistochemistry. At day 3, LIPUS had no effect on the rat orthodontic tooth movement distance and BMP-2-induced alveolar bone remodeling. However, beginning at day 5 and for the following time points, LIPUS significantly increased orthodontic tooth movement distance and BMP-2 signaling pathway and RANKL expression compared with the control group. The qRT-PCR and Western blot data in vitro and in vivo to study BMP-2 expression were consistent with the immunohistochemistry observations. The present study demonstrates that LIPUS promotes alveolar bone remodeling by stimulating the HGF/Runx2/BMP-2 signaling pathway and RANKL expression in a rat orthodontic tooth movement model, and LIPUS increased BMP-2 expression via Runx2 regulation.

Estrategias pasivas de optimización energética de la vivienda social en clima mediterráneo

Directory of Open Access Journals (Sweden)

Suárez, R.

2016-03-01

Full Text Available The main goals of Horizon 2020 have led to the updating of the Basic Document on Energy Saving of the Technical Building Code in 2013. The demands of the new model, based on technological and construction parameters, are associated with a more extensive assessment of the architectural conditions of buildings. This study aims to analyse the repercussion of the new regulations on Mediterranean social housing in climate zone B4. It proposes energy analysis on a basic model of a single linear block, adding different individual passive strategies relating to compactness, envelope material, solar control, solar accumulation and ventilation, analysing the improvement in energy demand, energy rating and indoor comfort. The main energy improvement actions used take into account orientation as well as the combined improvement in energy performance of the thermal envelope, ventilation rate and suitable solar protection. These lead to major reductions in energy demand and CO2 emissions while improving indoor comfort conditions.Los objetivos prioritarios del Horizonte 2020 han llevado a la actualización del Documento Básico de Ahorro de la Energía del CTE en 2013, introduciendo un nuevo modelo en las exigencias, basado en parámetros tecnológicos y constructivos, asociado a una mayor valoración de las condiciones arquitectónicas del edificio. Este trabajo pretende analizar la repercusión del nuevo marco normativo en la vivienda social del área mediterránea, en la zona climática B4. Se plantea el análisis energético en un modelo base de bloque lineal entre medianeras al que se incorporan individualmente, distintas estrategias pasivas asociadas a la compacidad, materialidad de la envolvente, control solar, acumulación solar y ventilación, analizando la mejora de la demanda de energía, la calificación energética y el confort interior. La consideración de la orientación, junto con la combinación de la mejora de las prestaciones energ

Nanosecond time-resolved EPR in pulse radiolysis via the spin echo method

International Nuclear Information System (INIS)

Trifunac, A.D.; Norris, J.R.; Lawler, R.G.

1979-01-01

The design and operation of a time-resolved electron spin echo spectrometer suitable for detecting transient radicals produced by 3 MeV electron radiolysis is described. Two modes of operation are available: Field swept mode which generates a normal EPR spectrum and kinetic mode in which the time dependence of a single EPR line is monitored. Techniques which may be used to minimize the effects of nonideal microwave pulses and overlapping sample tube signals are described. The principal advantages of the spin echo method over other time-resolved EPR methods are: (1) Improved time resolution (presently approx.30--50 nsec) allows monitoring of fast changes in EPR signals of transient radicals, (2) Lower susceptibility to interference between the EPR signal and the electron beam pulse at short times, and (3) Lack of dependence of transient signals on microwave field amplitude or static field inhomogeneity at short times. The performance of the instrument is illustrated using CIDEP from acetate radical formed in pulsed radiolysis of aqueous solutions of potassium acetate. The relaxation time and CIDEP enhancement factor obtained for this radical using the spin echo method compare favorably with previous determinations using direct detection EPR. Radical decay rates yield estimates of initial radical concentrations of 10 -4 10 -3 M per electron pulse. The Bloch equations are solved to give an expression for the echo signal for samples exhibiting CIDEP using arbitrary microwave pulse widths and distributions of Larmor frequencies. Conditions are discussed under which the time-dependent signal would be distorted by deviations from an ideal nonselective 90 0 --tau--180 0 pulse sequence

Optimally shaped narrowband picosecond pulses for femtosecond stimulated Raman spectroscopy.

Science.gov (United States)

Hoffman, David P; Valley, David; Ellis, Scott R; Creelman, Mark; Mathies, Richard A

2013-09-09

A comparison between a Fabry-Pérot etalon filter and a conventional grating filter for producing the picosecond (ps) Raman pump pulses for femtosecond stimulated Raman spectroscopy (FSRS) is presented. It is shown that for pulses of equal energy the etalon filter produces Raman signals twice as large as that of the grating filter while suppressing the electronically resonant background signal. The time asymmetric profile of the etalon-generated pulse is shown to be responsible for both of these observations. A theoretical discussion is presented which quantitatively supports this hypothesis. It is concluded that etalons are the ideal method for the generation of narrowband ps pulses for FSRS because of the optical simplicity, efficiency, improved FSRS intensity and reduced backgrounds.

El proyecto hidroeléctrico Coca Codo Sinclair y la gobernanza energética en la Amazonía ecuatoriana

Directory of Open Access Journals (Sweden)

Victor López

2013-10-01

Full Text Available Las condiciones en las que el Estado impulsa el cambio de la matriz energética, configuran problemas de gobernanza y retos para una gestión de energías renovables en la Amazonía, acorde con la Constitución y la planificación estatal del desarrollo. Coca Codo Sinclair (CCS es el mayor proyecto hidroeléctrico en implementación y apuntala las políticas de soberanía y eficiencia energética del gobierno, sin que se evidencien criterios de gestión integrada del recurso hídrico y equidad regional para las poblaciones locales.

El resurgimiento de la energía minihidráulica en España y su situación actual

OpenAIRE

Espejo Marín, Cayetano; García Marín, Ramón; Aparicio Guerrero, Ana Eulalia

2017-01-01

Las centrales minihidráulicas han sido una fuente de energía pionera para la producción de electricidad desde finales del siglo XIX. La crisis del petróleo en los años setenta del siglo XX puso de relieve la necesidad de apostar por las energías renovables, por su carácter autóctono, porque reducían la dependencia del exterior y por su menor impacto ambiental. Este artículo analiza la evolución de la energía minihidráulica en España desde mediados del siglo XX a la actualidad. El análisis del...

Spectral properties and associated plasma energization by magnetosonic waves in the Earth's magnetosphere: Particle-in-cell simulations

Science.gov (United States)

Sun, Jicheng; Gao, Xinliang; Lu, Quanming; Chen, Lunjin; Liu, Xu; Wang, Xueyi; Tao, Xin; Wang, Shui

2017-05-01

In this paper, we perform a 1-D particle-in-cell (PIC) simulation model consisting of three species, cold electrons, cold ions, and energetic ion ring, to investigate spectral structures of magnetosonic waves excited by ring distribution protons in the Earth's magnetosphere, and dynamics of charged particles during the excitation of magnetosonic waves. As the wave normal angle decreases, the spectral range of excited magnetosonic waves becomes broader with upper frequency limit extending beyond the lower hybrid resonant frequency, and the discrete spectra tends to merge into a continuous one. This dependence on wave normal angle is consistent with the linear theory. The effects of magnetosonic waves on the background cold plasma populations also vary with wave normal angle. For exactly perpendicular magnetosonic waves (parallel wave number k|| = 0), there is no energization in the parallel direction for both background cold protons and electrons due to the negligible fluctuating electric field component in the parallel direction. In contrast, the perpendicular energization of background plasmas is rather significant, where cold protons follow unmagnetized motion while cold electrons follow drift motion due to wave electric fields. For magnetosonic waves with a finite k||, there exists a nonnegligible parallel fluctuating electric field, leading to a significant and rapid energization in the parallel direction for cold electrons. These cold electrons can also be efficiently energized in the perpendicular direction due to the interaction with the magnetosonic wave fields in the perpendicular direction. However, cold protons can be only heated in the perpendicular direction, which is likely caused by the higher-order resonances with magnetosonic waves. The potential impacts of magnetosonic waves on the energization of the background cold plasmas in the Earth's inner magnetosphere are also discussed in this paper.

por energía de compactación y variación en la granulometría

Directory of Open Access Journals (Sweden)

Oscar Javier Reyes Ortiz

2006-01-01

Full Text Available El objetivo de esta investigación es establecer la influencia en las propiedades dinámicas de unas mezclas asfálticas por cambios en su energía de compactación y su granulometría. Para el desarrollo de la investigación se utilizaron dos tipos de mezcla asfálticas, una mezcla cerrada (0/10 y mezcla abierta (0/20 y la variación de la energía de compactación se realizo mediante cambios en los golpes por cada cara de las briquetas en su proceso de fabricación. La investigación inició con la caracterización de los materiales granulares y el asfalto. Posteriormente se les realizó el ensayo marshall a las mezclas para determinar el porcentaje óptimo de asfalto, el cual se obtuvo de las gráficas de estabilidad, flujo y peso unitario. Finalmente, se realizaron ensayos de módulos dinámicos y ahuellamiento, para poder concluir cual es la energía de compactación óptima que debe tener la mezcla asfáltica, y así, optimizar el diseño y funcionamiento de estructuras de pavimentos flexibles con diferentes tipos de granulometría. Dentro de los resultados se resalta que el mayor módulo dinámico para la mezcla cerrada (0/10 se obtuvo para una energía de compactación de 85 golpes y para la mezcla abierta (0/20 de 75 golpes. Con respecto a la deformación permanente se obtuvo las menores deformaciones para la energía de compactación de 90 golpes en la mezcla cerrada y de 85 golpes para la granulometría abierta.

System and process for pulsed multiple reaction monitoring

Science.gov (United States)

Belov, Mikhail E

2013-05-17

A new pulsed multiple reaction monitoring process and system are disclosed that uses a pulsed ion injection mode for use in conjunction with triple-quadrupole instruments. The pulsed injection mode approach reduces background ion noise at the detector, increases amplitude of the ion signal, and includes a unity duty cycle that provides a significant sensitivity increase for reliable quantitation of proteins/peptides present at attomole levels in highly complex biological mixtures.

Aplicación de sistemas de gestión energética sector comercio, caso hoteles

OpenAIRE

Auladell Roig, Marc

2012-01-01

El presente proyecto se centra en la realización de auditorías energéticas aplicadas en el sector terciario, más concretamente, en los establecimientos hoteleros. La primera parte consiste en la compilación de una base teórica sobre el tema con especial atención a las guías de ahorro publicadas por los entes públicos con competencia en medidas de eficiencia energética. Con posterioridad, se traslada la gestión de los conceptos teóricos adquiridos mediante una metodología ...

O contexto atual da reabilitação energética do parque edificado em Portugal

OpenAIRE

Abreu, Maria Isabel; Oliveira, Rui; Lopes, Jorge

2012-01-01

No seu Plano de Ação para a Eficiência Energética de 2011, a Comissão Europeia refere que o parque edificado apresenta um grande potencial de poupança energética. A nova Diretiva Europeia 2010/31/EU, em processo de transposição para legislação portuguesa, veio desafiar os estados membros a tomarem medidas ainda mais ambiciosas. Concretamente, estabelece que os estados membros elaborem planos periódicos onde constem instrumentos que reduzam as barreiras existentes e encorajem os investiment...

“estudio y simulación energética del edificio de la fiec con energyplus”

OpenAIRE

Briceño Maldonado, Richard Manuel

2013-01-01

En este documento se presenta el estudio energético y análisis de cargas térmicas del edificio de la Facultad de Ingeniería en Electricidad y Computación. El objetivo principal es realizar recomendaciones para disminuir la demanda de energía eléctrica debido a la excesiva carga térmica generada por los lucernarios de policarbonato alveolar. Se analizaron varias herramientas informáticas, y mediante matriz de decisión, se escogió a la denomina EnergyPlus. Se realizaron seis comparaciones a tra...

Implementación multimedia sobre energía fotovoltaica

OpenAIRE

Álvarez Santos, Alejandro; Giménez Oró, Nèstor

2004-01-01

El presente proyecto consiste en un programa informático que explica qué es la energía fotovoltaica, qué componentes tecnológicos se utilizan para su obtención y qué cálculos previos son necesarios para realizar la implementación de un campo de paneles solares. La herramienta elegida para realizar el programa informático, ha sido Macromedia Flash MX, versión 6.

Charge pulse preamplifier

International Nuclear Information System (INIS)

Libs, Gerard.

1973-01-01

A charge pulse preamplifier with very low background noise is described. The inlet stage of that preamplifier comprises a cooled field-effect transistor receiving the signal to be amplified at its gate input. Preferably, the charge resistor of said transistor is a field effect transistor, the source inlet of which is connected to the drain inlet of the former transistor through a self-induction coil and a resistor mounted in series. This can be applied to the treatment of the signals delivered by a particle detector in the form of a semi-conductor [fr

Effects of microwave pulse-width damage on a bipolar transistor

International Nuclear Information System (INIS)

Ma Zhen-Yang; Chai Chang-Chun; Ren Xing-Rong; Yang Yin-Tang; Chen Bin; Zhao Ying-Bo

2012-01-01

This paper presents a theoretical study of the pulse-width effects on the damage process of a typical bipolar transistor caused by high power microwaves (HPMs) through the injection approach. The dependences of the microwave damage power, P, and the absorbed energy, E, required to cause the device failure on the pulse width τ are obtained in the nanosecond region by utilizing the curve fitting method. A comparison of the microwave pulse damage data and the existing dc pulse damage data for the same transistor is carried out. By means of a two-dimensional simulator, ISE-TCAD, the internal damage processes of the device caused by microwave voltage signals and dc pulse voltage signals are analyzed comparatively. The simulation results suggest that the temperature-rising positions of the device induced by the microwaves in the negative and positive half periods are different, while only one hot spot exists under the injection of dc pulses. The results demonstrate that the microwave damage power threshold and the absorbed energy must exceed the dc pulse power threshold and the absorbed energy, respectively. The dc pulse damage data may be useful as a lower bound for microwave pulse damage data. (interdisciplinary physics and related areas of science and technology)

A Comparison of Fishes and Invertebrates Living in the Vicinity of Energized and Unenergized Submarine Power Cables and Natural Sea Floor off Southern California, USA

Directory of Open Access Journals (Sweden)

Milton S. Love

2017-01-01

Full Text Available Increasing reliance on deep-water renewable energy has increased concerns about the effects of the electromagnetic fields (EMFs generated by submarine power cables on aquatic organisms. Off southern California, we conducted surveys of marine organisms living around energized and unenergized submarine power cables and nearby sea floor during 2012–2014 at depths between 76 and 213 m. In general, EMFs declined to background levels about one meter from the cable. We found no statistical difference in species composition between the fish assemblages along the energized and unenergized cables. The natural habitat community statistically differed from both energized and unenergized cable communities. Within species (or species groups, we found no differences in densities between energized and unenergized cables. Total fish densities were significantly higher around the cables than over the natural habitat. We found that invertebrate communities were structured by habitat type and depth and, similar to the fishes, there was no statistical difference between the energized and unenergized cables. Individually, the densities of four invertebrate species or species groups (Metridium farcimen, Luidia spp., unidentified black Crinoidea, and Urticina spp. differed between energized and unenergized cables, but this difference was not significant across all depth strata. The invertebrate community inhabiting the natural habitat strongly differed from the energized and unenergized cable community exhibiting the fewest species and individuals.

Influencia del uso ineficiente de energía eléctrica en la competitividad de las empresas textiles peruanas: 2007 - 2008