WorldWideScience

Sample records for pulsed corona discharge

  1. Research on Nanosecond Pulse Corona Discharge Attenuation

    Institute of Scientific and Technical Information of China (English)

    HE Zheng-hao; XU Huai-li; BAI Jing; YU Fu-sheng; HU Feng; LI Jin

    2007-01-01

    A line-to-plate reactor was set-up in the experimental study on the application of nanosecond pulsed corona discharge plasma technology in environmental pollution control.Investigation on the attenuation and distortion of the amplitude of the pulse wave front and the discharge image as well as the waveform along the corona wire was conducted.The results show that the wave front decreases sharply during the corona discharge along the corona wire.The higher the amplitude of the applied pulse is,the more the amplitude of the wave front decreased.The wave attenuation responds in a lower corona discharge inversely.To get a higher efficiency of the line-to-plate reactor a sharp attenuation of the corona has to be considered in practical design.

  2. Device for generation of pulsed corona discharge

    Science.gov (United States)

    Gutsol, Alexander F [San Ramon, CA; Fridman, Alexander [Marlton, NJ; Blank, Kenneth [Philadelphia, PA; Korobtsev, Sergey [Moscow, RU; Shiryaevsky, Valery [Moscow, RU; Medvedev, Dmitry [Moscow, RU

    2012-05-08

    The invention is a method and system for the generation of high voltage, pulsed, periodic corona discharges capable of being used in the presence of conductive liquid droplets. The method and system can be used, for example, in different devices for cleaning of gaseous or liquid media using pulsed corona discharge. Specially designed electrodes and an inductor increase the efficiency of the system, permit the plasma chemical oxidation of detrimental impurities, and increase the range of stable discharge operations in the presence of droplets of water or other conductive liquids in the discharge chamber.

  3. Conversion of Methane to Hydrogen via Pulsed Corona Discharge

    Institute of Scientific and Technical Information of China (English)

    Lekha Nath Mishra; Kanetoshi Shibata; Hiroaki Ito; Noboru Yugami; Yasushi Nishida

    2004-01-01

    Experiments are performed to develop a pulsed corona discharge system for the conversion of methane to hydrogen at atmospheric pressure (≌760 Tort) without using a catalyst. The corona discharge was energized by 10-12 μs wide voltage pulses (≤7 kV) at a repetition rate of about 1.0-1.5 kHz. The residual gases were characterized by mass spectrometry. The conversion of methane is as high as 50.8%producing the 70% yield of hydrogen. The influences of argon on the discharge of methane were studied.This result could be useful for the mass production of hydrogen in both academic and industrial point of view.

  4. Pulsed Corona Discharges and Their Applications in Toxic VOCs Abatement

    Institute of Scientific and Technical Information of China (English)

    MuhammadArifMalik; SalmanAkbarMalik

    1999-01-01

    plasma processes are among the emerging technologies for volatile organic compounds (VOCs) sbatoment. Both thermal plasmas and non-equil[brimn plasmas (cold plasmas) are being developed for VOCs clesnup. Particularly, pulsed corona discharges offer several edvantages over conventional VOCs abatement tochniqvee, To optimize the existing technology and to developit further, there is need to understand the mechanlsms involved in plasma chemical reacticms, Furthermore, it is strongly desirable to be able to predict the behavior of new VOCs in non-equillbrlum plasma enviromuent from the data known for a few representative oompounds, Pulsed corona discharge technique is introduced here with dtafion of refevant literature, Fundamental principfes,useful for predicting the VOCs' decomposition behavior, have been worked out from the published literature. Latest developments in the area, targeted to minimize the enersy losses, improve the VOCs destruction efficiency and reduce the generation of unwanted organic and inorganic by-products, are presented.

  5. Pulsed corona discharge at atmospheric and supercritical conditions

    Science.gov (United States)

    Lock, Evgeniya Hristova

    Pulsed corona discharge is one of the non-equilibrium plasma techniques, by which electrical power is mainly utilized to generate high-energy electrons. These react further with the background gas to produce radicals, which can be further employed in chemically selective reactions. Study of the initiation of pulsed corona discharge in carbon dioxide and air was conducted. Furthermore due to its high removal efficiency, energy yields and good economy, the pulsed corona discharge was employed for removal of methanol and dimethyl sulfide. These compounds are part of the volatile organic compounds (VOC) air pollutants, which are subject of severe environmental regulations due to their toxicity, environmental persistence and intensity of smell. The study provides experimental data for the destruction of methanol and dimethyl sulfide from dry and humid air streams. The effects of the process parameters, including applied voltage, pulse repetition rate, initial concentration of pollutants, temperature and humidity on the destruction and removal efficiency and energy cost are analyzed. Specific consideration is given to the formation of unwanted byproducts. The study on plasma application for pollution control showed that small amounts of dispersed liquid droplets increase the efficiency of the chemical utilization of the high-energy electrons and reduce the required power. So media that could facilitate homogeneous and heterogeneous chemistry at the same time would enhance the efficiency of the removal process. Such medium that has properties intermediate between the gas and liquid phase is the supercritical fluid. Generation of plasma in supercritical fluids is an unexplored area in plasma science. The generation of plasma at elevated pressures usually requires high voltages or small interelectrode distances. The supercritical phase is characterized by extensive cluster formation in the vicinity of the critical point. Typically the clusters have lower ionization

  6. OH radicals generated by DC corona discharge for improving the pulsed discharge desulfuration efficiency

    Institute of Scientific and Technical Information of China (English)

    LI Jie; LI Guo-feng; WU Yan; WANG Ning-hui; HUANG Qiu-nan

    2004-01-01

    Positive DC corona discharge is formed with needle-plate electrode configuration, in which the water vapor is ejected though the needle points. The purpose is to increase the numbers of the water-based radicals, ionize the water molecule and improve the desulfuration efficiency of pulsed corona reactor. The water ions were determined by four stages molecular beam mass spectrometer and diagnose the water-based radicals by emission spectrograph. A conclusion on formation of ions and radicals with DC corona discharges can be drawn.

  7. The Experimental Investigations of Dielectric Barrier Discharge and Pulse Corona Discharge in Air Cleaning

    Institute of Scientific and Technical Information of China (English)

    左莉; 侯立安; 杨林松

    2003-01-01

    The dielectric barrier discharge (DBD) and pulse corona discharge(PCD) plasmagenerator was used to remove NH3, H2S, C7Hs etc. from atmosphere. The principle and charac-teristic of the two ways was discussed in the article. The test shows the result of PCD is betterthan that of DBD.

  8. Research on Nanosecond Pulse Corona Discharge with Cross Magnetic Field Applied

    Institute of Scientific and Technical Information of China (English)

    HE Zheng-hao; YU Fu-sheng; HU Feng; YUAN Yun; GUO Li-na; LI Jin

    2007-01-01

    An application of magnetic field to the nanosecond pulse corona discharge is investigated.A cylinder reactor with different corona electodes is set up for experimental study.A manetic field with its direction perpendicular to the corona discharge is applied.Different discharge images are taken under single nanosecond pulse with a high sensitive UV-visible light imagine recorder.Experimental results show that with a cross magnetic field the nanosecond out the magnetic field. The results may lead to a possibility to apply a cross magnetic field on nanosecond pulse corona discharge for getting higher desulfurization effciency.

  9. Partial oxidation of methane by pulsed corona discharges

    Science.gov (United States)

    Hoeben, W. F. L. M.; Boekhoven, W.; Beckers, F. J. C. M.; van Heesch, E. J. M.; Pemen, A. J. M.

    2014-09-01

    Pulsed corona-induced partial oxidation of methane in humid oxygen or carbon dioxide atmospheres has been investigated for future fuel synthesis applications. The obtained product spectrum is wide, i.e. saturated, unsaturated and oxygen-functional hydrocarbons. The generally observed methane conversion levels are 6-20% at a conversion efficiency of about 100-250 nmol J-1. The main products are ethane, ethylene and acetylene. Higher saturated hydrocarbons up to C6 have been detected. The observed oxygen-functional hydrocarbons are methanol, ethanol and lower concentrations of aldehydes, ketones, dimethylether and methylformate. Methanol seems to be exclusively produced with CH4/O2 mixtures at a maximum production efficiency of 0.35 nmol J-1. CH4/CO2 mixtures appear to yield higher hydrocarbons. Carboxylic acids appear to be mainly present in the aqueous reactor phase, possibly together with higher molecular weight species.

  10. Synthesis gas regeneration electrotechnology using volume high-voltage pulsed discharges: corona and barrier ones

    Directory of Open Access Journals (Sweden)

    M.I. Boyko

    2014-09-01

    Full Text Available Factory testing of a created high-voltage complex (plant has been conducted. The complex consists of two pulse generators with the repetition rate of up to 50,000 pulses per second and load reactors with pulsed discharges - corona and barrier ones. Transistor (IGBT keys are used as energy switches. The efficient mode of coke gas methane conversion (steam reforming to syngas has been obtained with application of the complex created. A unidirectional action of the pulsed discharges, the gas mixture temperature, and a nickel catalyst has reduced the specific energy consumption for synthesis gas regeneration during the conversion. A feasible mechanism of this conversion is described.

  11. Synergistic effect of pulsed corona discharges and ozonation on decolourization of methylene blue in water

    CERN Document Server

    Malik, M A; Ghaffar, A; Ahmed, K

    2002-01-01

    The effect of O sub 2 and O sub 3 bubbling on decolourization of methylene blue by pulsed corona discharges in water was studied. The pulsed corona discharges were produced by charging an 80 pF capacitor with a 40 kV DC source, through a 100 M OMEGA resistor, and discharging it into a needle-plate type reactor at 60 Hz through a rotating spark gap switch. A 20 ml sample of 13.25 mg l sup - sup 1 methylene blue in distilled water was decolourized in 120 min. Bubbling O sub 2 at 10 ml min sup - sup 1 through the discharge region reduced the decolourization time to 25 min. Bubbling O sub 2 containing 1500 mu mol O sub 3 l sup - sup 1 at 10 ml min sup - sup 1 reduced the decolourization time to 8 min. The O sub 3 was produced by fractionating input energy between a water treatment reactor and a O sub 3 generator, i.e. no additional energy was consumed for O sub 3 production. Under the same experimental conditions methylene blue solution in tap water was decolourized in >210 min by corona discharge in solution, in...

  12. Plasma sterilization of polyethylene terephthalate bottles by pulsed corona discharge at atmospheric pressure.

    Science.gov (United States)

    Masaoka, Satoshi

    2007-06-01

    A pulsed power supply was used to generate a corona discharge on a polyethylene terephthalate bottle, to conduct plasma sterilization at atmospheric pressure. Before generating such a discharge, minute quantities of water were attached to the inner surface of the bottle and to the surface of a high voltage (HV) electrode inserted into the bottle. Next, high-voltage pulses of electricity were discharged between electrodes for 6.0s, while rotating the bottle. The resulting spore log reduction values of Bacillus subtilis and Aspergillus niger on the inner surface of the bottle were 5.5 and 6 or higher, respectively, and those on the HV electrode surface were each 6 or higher for both strains. The presence of the by-products gaseous ozone, hydrogen peroxide, and nitric ions resulting from the electrical discharge was confirmed.

  13. Pulsed corona discharge: the role of ozone and hydroxyl radical in aqueous pollutants oxidation.

    Science.gov (United States)

    Preis, S; Panorel, I C; Kornev, I; Hatakka, H; Kallas, J

    2013-01-01

    Ozone and hydroxyl radical are the most active oxidizing species in water treated with gas-phase pulsed corona discharge (PCD). The ratio of the species dependent on the gas phase composition and treated water contact surface was the objective for the experimental research undertaken for aqueous phenol (fast reaction) and oxalic acid (slow reaction) solutions. The experiments were carried out in the reactor, where aqueous solutions showered between electrodes were treated with 100-ns pulses of 20 kV voltage and 400 A current amplitude. The role of ozone increased with increasing oxygen concentration and the oxidation reaction rate. The PCD treatment showed energy efficiency surpassing that of conventional ozonation.

  14. A method for removal of CO from exhaust gas using pulsed corona discharge.

    Science.gov (United States)

    Li, X; Yang, L; Lei, Y; Wang, J; Lu, Y

    2000-10-01

    An experimental study of the oxidation of CO in exhaust gas from a motorcycle has been carried out using plasma chemical reactions in a pulsed corona discharge. In the process, some main parameters, such as the initial CO concentration, amplitude and frequency of pulses, residence time, reactor volume, and relative humidity (RH), as well as their effects on CO removal characteristics, were investigated. O3, which is beneficial to reducing CO, was produced during CO removal. When the exhaust gas was at ambient temperature, more than 80% CO removal efficiency was realized at an initial concentration of 288 ppm in a suitable range of the parameters.

  15. Ordering of the flame track in the ring mode of the Trichel pulse negative corona discharge

    Science.gov (United States)

    Amirov, R. H.; Barengolts, S. A.; Korostylev, E. V.; Pestovskii, N. V.; Petrov, A. A.; Samoylov, I. S.; Savinov, S. Yu

    2014-11-01

    The ring mode of the Trichel pulse negative corona discharge was studied in atmospheric air. The localization of the discharge flame track in the stable self-organized regular pattern of 3, 4, 5 and 6 - pointed star was found at the cathode surface. This phenomenon was observed at mean currents in the range 100-115 μA at the conditions of the experiment, when the modes with one or two rings are not stable. The conclusion was made that the ring mode of the discharge, which is caused by the symmetrical distribution of the volumetric charges in the conditions of the symmetrical electric field, may be unstable. This instability results in the spatial self-organization of these parameters and causes the organization of the discharge flame track at the cathode surface in the regular patterns.

  16. Treatment of Dyeing Wastewater by Using Positive Pulsed Corona Discharge to Water Surface

    Institute of Scientific and Technical Information of China (English)

    Young Sun MOK; Hyun Tae AHN; Joeng Tai KIM

    2007-01-01

    This study investigated the treatment of textile-dyeing wastewater by using an electrical discharge technique (positive pulsed corona discharge). The high-voltage electrode was placed above the surface of the wastewater while the ground electrode was submerged in the wastewater. The electrical discharge starting at the tip of the high voltage electrode propagated toward the surface of the wastewater, producing various oxidative radicals and ozone. Oxygen was used as the working gas instead of air to prevent nitrogen oxides from forming. The simulated wastewater was made up with amaranth, which is a kind of azo dye. The results obtained showed that the chromaticity of the wastewater was almost completely removed within an hour. The ultraviolet/visible spectra of the wastewater treated by the electrical discharge revealed that the total hydrocarbon level also decreased significantly.

  17. Effect of pulsed corona discharge voltage and feed gas flow rate on dissolved ozone concentration

    Energy Technology Data Exchange (ETDEWEB)

    Prasetyaningrum, A., E-mail: ajiprasetyaningrum@gmail.com; Ratnawati,; Jos, B. [Department of Chemical Engineering, Faculty of Engineering, Diponegoro University Jl. Prof. H. Soedarto Tembalang, Semarang, Central Java, Indonesia, 50276 (Indonesia)

    2015-12-29

    Ozonization is one of the methods extensively used for water purification and degradation of organic materials. Ozone (O{sub 3}) is recognized as a powerful oxidizing agent. Due to its strong oxidability and better environmental friendless, ozone increasing being used in domestic and industrial applications. Current technology in ozone production utilizes several techniques (corona discharge, ultra violet radiation and electrolysis). This experiment aimed to evaluating effect of voltage and gas flow rate on ozone production with corona discharge. The system consists of two net-type stainless steel electrode placed in a dielectric barrier. Three pulsed voltage (20, 30, 40 KV) and flow rate (5, 10, 15 L/min) were prepare for operation variable at high frequency (3.7 kHz) with AC pulsed power supply. The dissolved ozone concentration depends on the applied high-voltage level, gas flow rate and the discharge exposure duration. The ozone concentration increases with decreasing gas flow rate. Dissolved ozone concentrations greater than 200 ppm can be obtained with a minimum voltage 40 kV.

  18. Beyond-thermal-equilibrium" conversion of methane to acetylene and hydrogen under pulsed corona discharge

    Institute of Scientific and Technical Information of China (English)

    朱爱民; 宫为民; 张秀玲; 李小松

    2002-01-01

    At ambient temperature and pressure, C2H2 and H2 are the dominating products from pure methane conversion under pulsed corona discharge (PCD). When the energy density of 194-1788 kJ/mol was applied, 7%-30% of C2H2 yield and 6%-35% of H2 yield per pass have been obtained. These results are higher than the maximum thermodynamic yield of C2H2 (5.1%) and H2 (3.8%) at 100 kPa and 1100 K, respectively. Thereby, pulsed corona discharge is a very effective tool for "beyond-thermal-equilibrium" conversion of methane to C2H2 and H2 at ambient temperature and pressure. In the PCD energy density range of 339-822 kJ/mol, the carbon distribution of the methane conversion products is found to be: C2H2 86%-89%, C2H6 4%-6%, C2H4 4%-6%, C3 -2%, C4 -1%. Through comparison of the product from pure methane, ethane and ethylene conversion at the same discharge conditions, it can be concluded that three pathways may be responsible for the C2H2 formation via CHx radicals produced from the collisions of CH4 molecules with energi

  19. Transitions between corona, glow, and spark regimes of nanosecond repetitively pulsed discharges in air at atmospheric pressure

    OpenAIRE

    Pai, David,; Lacoste, Deanna,; Laux, C.

    2010-01-01

    International audience; In atmospheric pressure air preheated from 300 to 1000 K, the nanosecond repetitively pulsed (NRP) method has been used to generate corona, glow, and spark discharges. Experiments have been performed to determine the parameter space (applied voltage, pulse repetition frequency, ambient gas temperature, and interelectrode gap distance) of each discharge regime. In particular, the experimental conditions necessary for the glow regime of NRP discharges have been determine...

  20. Partial Discharge Optical Pulse Signal Characteristics for Corona Defect in Oil Immersed Transformer

    Directory of Open Access Journals (Sweden)

    Jiabin Zhou

    2013-03-01

    Full Text Available Using fluorescent fiber sensor in transformer PD detection is a new method, based on the experimental platform for corona PD defect, the study has been carried out in order to show the typical corona PD defect optical pulse signal characteristics, PD single pulse waveform and pulses under industrial frequency cycle were acquired. The test results show that the optical method by using fluorescent fiber is effective in PD detection and corona PD optical pulse signals can accurately reflect the characteristics for this kind defect.

  1. Investigation of a physical disinfection process based on pulsed underwater corona discharges

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, S.B.

    2007-09-15

    To overcome the side effects of commonly used water disinfection methods based on chemicals, advanced oxidation processes (AOP's) are presently considered as an alternative. These processes are based on the effect of highly reactive oxidants (like ozone, OH radicals, H{sub 2}O{sub 2}, et.) on microorganisms and toxic organic compounds. In this work the effects and products from pulsed underwater corona discharges have been investigated for their potential to remove contaminants from the water. Pulsed underwater corona discharges create oxidative and reductive species, UV radiation, shock waves and strong electric field at the tip of propagating streamers. It has been supposed that the combined appearance of these effects leads to an effective destruction of contaminants in the water. It was the aim of this work to quantify the production rates of oxidants and the intensity of other effects from underwater corona discharges, to demonstrate their effectiveness for the inactivation of microorganisms and to propose a suitable corona reactor that is scalable to large throughputs. For that purpose a coaxial corona reactor was designed with a central anode covered by a thin (200-300 {mu}m) porous ceramic layer. The conductive porous ceramic and the anode cathode water gap form a parallel resistive-capacitive voltage divider. For times greater than the dielectric relaxation time of the water ({tau}={epsilon}{epsilon}{sub 0}/{sigma}) resistive voltage division dominates and the electric field at the ceramic layer can be more enhanced than in the case of capacitive voltage division. Applying a pulsed voltage of 30-50 kV for a duration of 200-400 ns to the anode a large number of streamers is launched homogeneously from the ceramic surface extending up to 10 mm into the anode cathode water gap. An L-C chain Blumlein configuration has been selected to generate the pulses. By changing the number and the values of the LC elements the impedance of the generator and its pulse

  2. A volume pulsed corona formed during nanosecond pulsed periodic discharge of negative polarity in narrow gaps with airflow at atmospheric pressure

    Science.gov (United States)

    Lepekhin, N. M.; Priseko, Yu. S.; Puresev, N. I.; Filippov, V. G.

    2014-06-01

    A volume mode of spatially homogeneous nanosecond pulsed-periodic corona discharge of negative polarity has been obtained using an edge-to-edge electrode geometry in narrow gaps with airflow at atmospheric pressure and natural humidity. The parameters of discharge are estimated, and a factor limiting the power deposited in discharge is determined.

  3. Analysis of Current Pulses in HeLa-Cell Permeabilization Due to High Voltage DC Corona Discharge.

    Science.gov (United States)

    Chetty, Nevendra K; Chonco, Louis; Ijumba, Nelson M; Chetty, Leon; Govender, Thavendran; Parboosing, Raveen; Davidson, Innocent E

    2016-09-01

    Corona discharges are commonly utilized for numerous practical applications, including bio-technological ones. The corona induced transfer of normally impermeant molecules into the interior of biological cells has recently been successfully demonstrated. The exact nature of the interaction of the corona discharge with a cell membrane is still unknown, however, previous studies have suggested that it is either the electric fields produced by ions or the chemical interaction of the reactive species that result in the disruption of the cell membrane. This disruption of the cell membrane allows molecules to permeate into the cell. Corona discharge current constitutes a series of pulses, and it is during these pulses that the ions and reactive species are produced. It stands to reason, therefore, that the nature of these corona pulses would have an influence on the level of cell permeabilization and cell destruction. In this investigation, an analysis of the width, rise-time, characteristic frequencies, magnitude, and repetition rate of the nanosecond pulses was carried out in order to establish the relationship between these factors and the levels of cell membrane permeabilization and cell destruction. Results obtained are presented and discussed.

  4. [Study of a wire-to-plate positive pulsed corona discharge reactor by emission spectroscopy].

    Science.gov (United States)

    Wang, Shen-Bing; Luo, Zhong-Yang; Zhao, Lei; Xuan, Jian-Yong; Jiang, Jian-Ping; Cen, Ke-Fa

    2011-11-01

    In order to get extensive knowledge of wire-to-plate pulsed corona discharge reactor, the influences of different diameters of wire electrode, different wire-to-plate and wire-to-wire spacing on OH radical generation were experimentally investigated under atmospheric pressure based on emission spectrum, and the spatial distribution of OH radicals in the electric field was also discussed in detail The results showed that OH radicals decrease along the X-axis, and the activation radius is approximately 20 mm; showing a trend of first increase and then decrease along the Y-axis, with the activation radius being more than 30 mm. OH radical has small change as the diameter of wire electrode changes below 2 mm, with a sharp decline as the diameter continues to increase. OH radical emission intensity increases as wire-to-wire spacing increases and decrease as wire-to-plate spacing increases.

  5. Evaluation of pulsed corona discharge plasma for the treatment of petroleum-contaminated soil.

    Science.gov (United States)

    Li, Rui; Liu, Yanan; Mu, Ruiwen; Cheng, Wenyan; Ognier, Stéphanie

    2017-01-01

    Petroleum hydrocarbons released to the environment caused by leakage or illegal dumping pose a threat to human health and the natural environment. In this study, the potential of a pulsed corona discharge plasma system for treating petroleum-polluted soils was evaluated. This system removed 76.93 % of the petroleum from the soil in 60 min with an energy efficiency of 0.20 mg/kJ. Furthermore, the energy and degradation efficiencies for the remediation of soil contaminated by single polyaromatic hydrocarbons, such as phenanthrene and pyrene, were also compared, and the results showed that this technology had potential in organic-polluted soil remediation. In addition, the role of water molecules was investigated for their direct involvement in the formation and transportation of active species. The increase of soil moisture to a certain extent clearly benefitted degradation efficiency. Then, treated soils were analyzed by FTIR and GC-MS for proposing the degradation mechanism of petroleum. During the plasma discharging processes, the change of functional group and the detection of small aromatic hydrocarbons indicated that the plasma active species attached petroleum hydrocarbons and degradation occurred. This technique reported herein demonstrated significant potential for the remediation of heavily petroleum-polluted soil, as well as for the treatment of organic-polluted soils.

  6. Industrial-scale experiments of desulfuration of coal flue gas using a pulsed corona discharge plasma

    Energy Technology Data Exchange (ETDEWEB)

    Li, J.; Wu, Y.; Wang, N.H.; Li, G.F.; Huang, Q.N. [Dalian University of Technology, Dalian (China). Inst. of Electrostatics

    2003-06-01

    The flow rate of flue gas in the industrial experiments was 3000 Nm{sup 3}/h. The flue gas from the boiler burning coal was used. The influences of operating parameters on the efficiency of desulfurization (DeSO{sub 2}) were studied, which include the retention period of flue gas in the reactor, the initial concentration of SO{sub 2} in flue gas, a mole ratio of NH{sub 3} to SO{sub 2} in the gas, the temperature of the gas, as well as the power consumption of pulsed corona discharges. The experimental results shown that the efficiency of DeSO{sub 2} was above 80%, when the initial concentration of SO{sub 2} was 1000 -2000 ppm, the gas temperature was 60 - 75 {degree}C, the retention period was more than 5.8 s, a mole ratio of NH{sub 3} to SO{sub 2} was 2:1, the water content in flue gas was above 6%, and the consumption was 2.5-3.5 Wh/Nm{sup 3}.

  7. Low-temperature NOx reduction processes using combined systems of pulsed corona discharge and catalysts

    Science.gov (United States)

    Kim, H. H.; Takashima, K.; Katsura, S.; Mizuno, A.

    2001-02-01

    In this paper, we will report NOx removal via reduction processes using two types of combined system of pulse corona discharge and catalysts: the single-stage plasma-driven catalyst (PDC) system, and the two-stage plasma-enhanced selective catalytic reduction (PE-SCR) system. Several catalysts, such as γ-alumina catalysts, mechanically mixed catalysts of γ-alumina with BaTiO3 or TiO2, and Co-ZSM-5 were tested. In the PDC system, which is directly activated by the discharge plasma, it was found that the use of additives was necessary to achieve NOx removal by reduction. Removal rates of NO and NOx were linearly increased as the molar ratio of additive to NOx increased. The dependence of NO and NOx removal on the gas hourly space velocity (GHSV) at a fixed specific input energy (SIE) indicates that plasma-induced surface reaction on the catalyst plays an important role in the PDC system. It was found that the optimal GHSV of the PDC system with the γ-alumina catalyst was smaller than 6000 h-1. Mechanical mixing of γ-alumina with BaTiO3 or TiO2 did not enhance NO and NOx removal and γ-alumina alone was found to be the most suitable catalyst. The dielectric constant of the catalyst only influenced the plasma intensity, not the NOx removal. In the PE-SCR system, plasma-treated NOx (mostly NO2) was reduced effectively with NH3 over the Co-ZSM-5 catalyst at a relatively low temperature of 150 °C. Under optimal conditions the energy cost and energy yield were 25 eV/molecule and 21 g-N (kWh)-1, respectively.

  8. Transitions between corona, glow, and spark regimes of nanosecond repetitively pulsed discharges in air at atmospheric pressure

    Science.gov (United States)

    Pai, David Z.; Lacoste, Deanna A.; Laux, Christophe O.

    2010-05-01

    In atmospheric pressure air preheated from 300 to 1000 K, the nanosecond repetitively pulsed (NRP) method has been used to generate corona, glow, and spark discharges. Experiments have been performed to determine the parameter space (applied voltage, pulse repetition frequency, ambient gas temperature, and interelectrode gap distance) of each discharge regime. In particular, the experimental conditions necessary for the glow regime of NRP discharges have been determined, with the notable result that there exists a minimum and maximum gap distance for its existence at a given ambient gas temperature. The minimum gap distance increases with decreasing gas temperature, whereas the maximum does not vary appreciably. To explain the experimental results, an analytical model is developed to explain the corona-to-glow (C-G) and glow-to-spark (G-S) transitions. The C-G transition is analyzed in terms of the avalanche-to-streamer transition and the breakdown field during the conduction phase following the establishment of a conducting channel across the discharge gap. The G-S transition is determined by the thermal ionization instability, and we show analytically that this transition occurs at a certain reduced electric field for the NRP discharges studied here. This model shows that the electrode geometry plays an important role in the existence of the NRP glow regime at a given gas temperature. We derive a criterion for the existence of the NRP glow regime as a function of the ambient gas temperature, pulse repetition frequency, electrode radius of curvature, and interelectrode gap distance.

  9. Decontamination of Streptococci biofilms and Bacillus cereus spores on plastic surfaces with DC and pulsed corona discharges

    Science.gov (United States)

    Koval'ová, Zuzana; Tarabová, Kataŕna; Hensel, Karol; Machala, Zdenko

    2013-02-01

    Cold air plasmas of DC and pulsed corona discharges: positive streamers and negative Trichel pulses were used for bio-decontamination of Streptococci biofilm and Bacillus cereus spores on polypropylene plastic surfaces. The reduction of bacterial population (evaluated as log10) in the biofilm on plastic surfaces treated by DC corona reached 2.4 logs with 10 min treatment time and 3.3 logs with 2 min treatment time with water spraying. The enhancement of plasma biocidal effects on the biofilm by electro-spraying of water through a hollow needle high-voltage electrode was investigated. No significant polarity effect was found with DC corona. Pulsed corona was demonstrated slightly more bactericidal for spores, especially in the negative polarity where the bacterial population reduction reached up to 2.2 logs at 10 min exposure time. Contribution to the Topical Issue "13th International Symposium on High Pressure Low Temperature Plasma Chemistry (Hakone XIII)", Edited by Nicolas Gherardi, Henryca Danuta Stryczewska and Yvan Ségui.

  10. Effect Of Gas Mixture Composition On Tar Removal Process In A Pulsed Corona Discharge Reactor

    Science.gov (United States)

    Filimonova E.; Naidis, G.

    2010-07-01

    The simulation of naphthalene (C10H8) removal from several gas mixtures (pure nitrogen, mixtures containing N2 with CO2, CO, H2, H2O, and biogas - the product of biomass gasification), has been investigated. The modeling is based on the experimental data obtained in the reactor with a pulsed positive corona discharge. The problem of simulation of the cleaning process includes description of two stages. The first, fast stage is generation of primary active species during streamer propagation. The second, slow stage is the chain of chemical transformations triggered by these species. The input parameters for the modeling of the second stage are G-values for generation of primary active species, obtained under consideration of streamer dynamics. Simulation of the second stage of the removal process takes into account the processes of chemical kinetics and diffusion outside and inside of streamer traces during multi-pulsed treatment. Besides neutral active species, streamer discharges produce electrons and ions. Primary positive ions (N2+, CO+, CO2+, H2+, H2O+) in a chain of fast ion-molecule reactions transform into more stable positive ions. The ions recombine with electrons. Both ion-molecule reactions and electron-ion recombination process are additional (to dissociation of gas molecules by electron impact in the streamer head) sources of neutral active species. The relative contribution of these sources to the G-values for H, OH and O is rather large. In our modeling two approaches have been used. At the first approach the contribution of ion-molecule reactions is estimated approximately assuming that the dominating stable ion is N4+ (in pure N2 and its mixtures with H2) or CO2+ (in mixtures including CO2). Other way is the calculations with kinetic scheme including the molecular ions, aquated ions such as H3O(H2O)m+, NO2(H2O)-, NO2(H2O)+ and other. The comparison of results of two approaches is presented. Only full kinetic scheme allowed describing the

  11. Experimental and modeling study of the oxidation of acetaldehyde in an atmospheric-pressure pulsed corona discharge

    Science.gov (United States)

    Klett, C.; Touchard, S.; Vega-Gonzalez, A.; Redolfi, M.; Bonnin, X.; Hassouni, K.; Duten, X.

    2012-08-01

    This paper reports the results obtained for the degradation of acetaldehyde by an atmospheric plasma corona discharge working in a pulsed regime. It was shown that a few hundred ppm of acetaldehyde diluted in a pure N2 gas flow can be removed up to 80% by a discharge fed with an electric power lower than 1 W. Under the same conditions, adding up to 5% of O2 allowed the removal of up to 95% of the initial acetaldehyde. The main identified end products were CO2, CO and methanol. A quasi-homogeneous zero-dimensional chemical model was developed to investigate the respective efficiency of the discharge and post-discharge periods in the global removal of the pollutant. The identified main pathways of acetaldehyde degradation were quenching of N2 metastable states during plasma pulses and oxidation by O and OH radicals during the post-discharge. This latter contribution increased with input power because of ozone accumulation in the gas mixture acting as an additional oxygen reservoir.

  12. 电晕线串并联的脉冲电晕放电特性%Pulse Corona Discharge Characteristics of the Line-to-plate Reactor with Series and Parallel Corona Wire

    Institute of Scientific and Technical Information of China (English)

    何正浩; 李劲

    2001-01-01

    The V-A characteristics of nanosecond pulse corona discharge with different corona wire length in series and parallel in the line-to-plate pulse corona discharge reactor is measured.It investigates the different features of the pulse corona discharge while the corona wires are connected in series and parallel. It is known from the study that the V-A characteristics of nanosecond pulse corona discharge trends to rise as exponential function. The corona currents with the wire in series increase as logarithmic function with the increase of the corona wire. But the corona currents with the wire in parallel increase as linear function with the increase of the corona wire. The results suggest that the corona wires is better to be connected in parallel in practical design for getting high corona discharge efficiency and the corona wire shouldn’t be long.%在线板结构脉冲电晕放电试验模型上,测试了不同长度电晕线串并联时的ns脉冲电晕放电伏安特性,研究了电晕线串并联时脉冲电晕放电的不同特点。研究表明ns脉冲电晕放电伏安特性呈指数函数上升趋势,串联电晕线的电晕电流随其长度的增长为自然对数函数上升趋势,并联电晕线的电晕 电流随其长度的增长为线形函数上升趋势。根据研究,实际设计脉冲电晕放电反应器时,为提高反应器效率,多根电晕线应并联而不宜串联,且电晕线不宜过长。

  13. Snowfall induced by corona discharge

    CERN Document Server

    Ju, Jingjing; Li, Ruxin; Du, Shengzhe; Sun, Haiyi; Liu, Yonghong; Tian, Ye; Bai, Yafeng; Liu, Yaoxiang; Chen, Na; Wang, Jingwei; Wang, Cheng; Liu, Jiansheng; Chin, S L; Xu, Zhizhan

    2016-01-01

    We demonstrated for the first time the condensation and precipitation (or snowfall) induced by a corona discharge inside a cloud chamber. Ionic wind was found to have played a more significant role than ions as extra Cloud Condensation Nuclei (CCN). 2.25 g of net snow enhancement was measured after applying a 30 kV corona discharge for 25 min. In comparison with another newly emerging femtosecond laser filamentation method, the snow precipitation induced by the corona discharge has about 4 orders of magnitude higher wall-plug efficiency under similar conditions.

  14. Comparative study of NO removal in surface-plasma and volume-plasma reactors based on pulsed corona discharges.

    Science.gov (United States)

    Malik, Muhammad Arif; Kolb, Juergen F; Sun, Yaohong; Schoenbach, Karl H

    2011-12-15

    Nitric oxide (NO) conversion has been studied for two different types of atmospheric-pressure pulsed-corona discharges, one generates a surface-plasma and the other provides a volume-plasma. For both types of discharges the energy cost for NO removal increases with decreasing oxygen concentration and initial concentration of NO. However, the energy cost for volume plasmas for 50% NO removal, EC(50), from air was found to be 120 eV/molecule, whereas for the surface plasma, it was only 70 eV/molecule. A smaller difference in energy cost, but a higher efficiency for removal of NO was obtained in a pure nitrogen atmosphere, where NO formation is restricted due to the lack of oxygen. For the volume plasma, EC(50) in this case was measured at 50 eV/molecule, and for the surface plasma it was 40 eV/molecule. Besides the higher NO removal efficiency of surface plasmas compared to volume plasmas, the energy efficiency of surface-plasmas was found to be almost independent of the amount of electrical energy deposited in the discharge, whereas the efficiency for volume plasmas decreases considerably with increasing energy. This indicates the possibility of operating surface plasma discharges at high energy densities and in more compact reactors than conventional volume discharges.

  15. Comparative study of NO removal in surface-plasma and volume-plasma reactors based on pulsed corona discharges

    Energy Technology Data Exchange (ETDEWEB)

    Malik, Muhammad Arif, E-mail: MArifMalik@gmail.com [Frank Reidy Research Center for Bioelectrics, Old Dominion University, 4211 Monarch Way, Suite 300, Norfolk, VA 23508 (United States); Kolb, Juergen F.; Sun, Yaohong; Schoenbach, Karl H. [Frank Reidy Research Center for Bioelectrics, Old Dominion University, 4211 Monarch Way, Suite 300, Norfolk, VA 23508 (United States)

    2011-12-15

    Nitric oxide (NO) conversion has been studied for two different types of atmospheric-pressure pulsed-corona discharges, one generates a surface-plasma and the other provides a volume-plasma. For both types of discharges the energy cost for NO removal increases with decreasing oxygen concentration and initial concentration of NO. However, the energy cost for volume plasmas for 50% NO removal, EC{sub 50}, from air was found to be 120 eV/molecule, whereas for the surface plasma, it was only 70 eV/molecule. A smaller difference in energy cost, but a higher efficiency for removal of NO was obtained in a pure nitrogen atmosphere, where NO formation is restricted due to the lack of oxygen. For the volume plasma, EC{sub 50} in this case was measured at 50 eV/molecule, and for the surface plasma it was 40 eV/molecule. Besides the higher NO removal efficiency of surface plasmas compared to volume plasmas, the energy efficiency of surface-plasmas was found to be almost independent of the amount of electrical energy deposited in the discharge, whereas the efficiency for volume plasmas decreases considerably with increasing energy. This indicates the possibility of operating surface plasma discharges at high energy densities and in more compact reactors than conventional volume discharges.

  16. Potential of pulsed corona discharges generated in water for the degradation of persistent pharmaceutical residues.

    Science.gov (United States)

    Banaschik, Robert; Lukes, Petr; Jablonowski, Helena; Hammer, Malte U; Weltmann, Klaus-Dieter; Kolb, Juergen F

    2015-11-01

    Anthropogenic pollutants and in particular pharmaceutical residues are a potential risk for potable water where they are found in increasing concentrations. Different environmental effects could already be linked to the presence of pharmaceuticals in surface waters even for low concentrations. Many pharmaceuticals withstand conventional water treatment technologies. Consequently, there is a need for new water purification techniques. Advanced oxidation processes (AOP), and especially plasmas with their ability to create reactive species directly in water, may offer a promising solution. We developed a plasma reactor with a coaxial geometry to generate large volume corona discharges directly in water and investigated the degradation of seven recalcitrant pharmaceuticals (carbamazepine, diatrizoate, diazepam, diclofenac, ibuprofen, 17α-ethinylestradiol, trimethoprim). For most substances we observed decomposition rates from 45% to 99% for treatment times of 15-66 min. Especially ethinylestradiol and diclofenac were readily decomposed. As an inherent advantage of the method, we found no acidification and only an insignificant increase in nitrate/nitrite concentrations below legal limits for the treatment. Studies on the basic plasma chemical processes for the model system of phenol showed that the degradation is primarily caused by hydroxyl radicals.

  17. Spatial and temporal evolutions of ozone in a nanosecond pulse corona discharge at atmospheric pressure

    Science.gov (United States)

    Duten, X.; Redolfi, M.; Aggadi, N.; Vega, A.; Hassouni, K.

    2011-10-01

    This paper deals with the experimental determination of the spatial and temporal evolutions of the ozone concentration in an atmospheric pressure pulsed plasma, working in the nanosecond regime. We observed that ozone was produced in the localized region of the streamer. The ozone transport requires a characteristic time well above the millisecond. The numerical modelling of the streamer expansion confirms that the hydrodynamic expansion of the filamentary discharge region during the streamer propagation does not lead to a significant transport of atomic oxygen and ozone. It appears therefore that only diffusional transport can take place, which requires a characteristic time of the order of 50 ms.

  18. Spatial and temporal evolutions of ozone in a nanosecond pulse corona discharge at atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Duten, X; Redolfi, M; Aggadi, N; Vega, A; Hassouni, K, E-mail: duten@lspm.cnrs.fr [LSPM-CNRS UPR 3407, Universite Paris Nord, 90 Avenue J.B. Clement, 93430 Villetaneuse (France)

    2011-10-19

    This paper deals with the experimental determination of the spatial and temporal evolutions of the ozone concentration in an atmospheric pressure pulsed plasma, working in the nanosecond regime. We observed that ozone was produced in the localized region of the streamer. The ozone transport requires a characteristic time well above the millisecond. The numerical modelling of the streamer expansion confirms that the hydrodynamic expansion of the filamentary discharge region during the streamer propagation does not lead to a significant transport of atomic oxygen and ozone. It appears therefore that only diffusional transport can take place, which requires a characteristic time of the order of 50 ms.

  19. Reduction of low-density lipoprotein cholesterol, plasma viscosity, and whole blood viscosity by the application of pulsed corona discharges and filtration

    Science.gov (United States)

    Jung, Jin M.; Fridman, Alexander; Cho, Daniel J.; Cho, Young I.

    2013-03-01

    The present study investigated the feasibility of applying pulsed corona discharges to blood plasma to reduce the viscosity of blood plasma and whole blood. Blood plasma was separated from blood cells, treated with corona discharges, and filtered before it was re-mixed with blood cells. Plasma viscosity (PV), whole blood viscosity (WBV), and low-density lipoprotein (LDL)-c concentration were measured before and after the corona treatment and filtration. Both PV and WBV increased in the case of the corona treatment only, whereas both of them decreased in the case of the corona treatment plus filtration. In particular, the LDL-c decreased in the case of the corona treatment plus filtration by 31.5% from the baseline value. The effect of the corona treatment on the reduction of the WBV was significant at low shear rates, but not at high shear rates, suggesting that the precipitation of the molecules in blood plasma by the corona treatment and subsequent removal may suppress the aggregation of erythrocytes and improve rheological properties of blood.

  20. Reduction of low-density lipoprotein cholesterol, plasma viscosity, and whole blood viscosity by the application of pulsed corona discharges and filtration.

    Science.gov (United States)

    Jung, Jin M; Fridman, Alexander; Cho, Daniel J; Cho, Young I

    2013-03-01

    The present study investigated the feasibility of applying pulsed corona discharges to blood plasma to reduce the viscosity of blood plasma and whole blood. Blood plasma was separated from blood cells, treated with corona discharges, and filtered before it was re-mixed with blood cells. Plasma viscosity (PV), whole blood viscosity (WBV), and low-density lipoprotein (LDL)-c concentration were measured before and after the corona treatment and filtration. Both PV and WBV increased in the case of the corona treatment only, whereas both of them decreased in the case of the corona treatment plus filtration. In particular, the LDL-c decreased in the case of the corona treatment plus filtration by 31.5% from the baseline value. The effect of the corona treatment on the reduction of the WBV was significant at low shear rates, but not at high shear rates, suggesting that the precipitation of the molecules in blood plasma by the corona treatment and subsequent removal may suppress the aggregation of erythrocytes and improve rheological properties of blood.

  1. Helium corona-assisted air discharge

    Energy Technology Data Exchange (ETDEWEB)

    Jiang Nan; Gao Lei; Ji Ailing; Cao Zexian [Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China)

    2011-10-15

    Operation of atmospheric discharge of electronegative gases including air at low voltages yet without consuming any inert gas will enormously promote the application of non-thermal plasmas. By taking advantage of the low onset voltage for helium corona, air discharge was successfully launched at much reduced voltages with a needle-plate system partly contained in a helium-filled glass bulb--for a needle-plate distance of 12 mm, 1.0 kV suffices. Ultraviolet emission from helium corona facilitates the discharging of air, and the discharge current manifests distinct features such as relatively broad Trichel pulses in both half periods. This design allows safe and economic implementation of atmospheric discharge of electronegative gases, which will find a broad palette of applications in surface modification, plasma medicine and gas treatment, etc.

  2. An investigation of CO2 splitting using nanosecond pulsed corona discharge: effect of argon addition on CO2 conversion and energy efficiency

    Science.gov (United States)

    Moss, M. S.; Yanallah, K.; Allen, R. W. K.; Pontiga, F.

    2017-03-01

    The plasma chemical splitting of carbon dioxide (CO2) to produce carbon monoxide (CO) in a pulsed corona discharge was investigated from both an experimental and a numerical standpoint. High voltage nanosecond pulses were applied to a stream of pure CO2 and its mixture with argon, and the gaseous products were identified using Fourier transform infrared spectroscopy. Due to the shape of pulses, the process of CO2 splitting was found to proceed in two phases. The first phase is dominated by ionization, which generates a high electron density. Then, during the second phase, direct electron impact dissociation of CO2 contributes to a large portion of CO production. Conversion and energy efficiency were calculated for the tested conditions. The conversions achieved are comparable to those obtained using other high pressure non-thermal discharges, such as dielectric barrier discharge. However, the energy efficiencies were considerably higher, which are favorable to industrial applications that require atmospheric conditions and elevated gas flow rates.

  3. Production mechanism of atomic nitrogen in atmospheric pressure pulsed corona discharge measured using two-photon absorption laser-induced fluorescence

    Energy Technology Data Exchange (ETDEWEB)

    Teramoto, Yoshiyuki; Ono, Ryo [Department of Advanced Energy, University of Tokyo, 5-1-5 Kashiwanoha, Kashiwa, Chiba 227-8568 (Japan); Oda, Tetsuji [Department of Electrical Engineering, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan)

    2012-06-01

    To study the production mechanism of atomic nitrogen, the temporal profile and spatial distribution of atomic nitrogen are measured in atmospheric pressure pulsed positive corona discharge using two-photon absorption laser-induced fluorescence. The absolute atomic nitrogen density in the streamer filaments is estimated from decay rate of atomic nitrogen in N{sub 2} discharge. The results indicate that the absolute atomic nitrogen density is approximately constant against discharge energy. When the discharge voltage is 21.5 kV, production yield of atomic nitrogen produced by an N{sub 2} discharge pulse is estimated to be 2.9 - 9.8 Multiplication-Sign 10{sup 13} atoms and the energy efficiency of atomic nitrogen production is estimated to be about 1.8 - 6.1 Multiplication-Sign 10{sup 16} atoms/J. The energy efficiency of atomic nitrogen production in N{sub 2} discharge is constant against the discharge energy, while that in N{sub 2}/O{sub 2} discharge increases with discharge energy. In the N{sub 2}/O{sub 2} discharge, two-step process of N{sub 2} dissociation plays significant role for atomic nitrogen production.

  4. Measurement of vibrationally excited N2(v) in an atmospheric-pressure air pulsed corona discharge using coherent anti-Stokes Raman scattering

    Science.gov (United States)

    Teramoto, Yoshiyuki; Ono, Ryo

    2014-08-01

    Vibrationally excited N2(v = 1, 2) in an atmospheric-pressure air pulsed corona discharge was measured using coherent anti-Stokes Raman scattering (CARS). In a dry air discharge, the vibrational temperature determined from the ratio N2(v = 2)/N2(v = 0), Tv2, was approximately 500 K higher than that determined from N2(v = 1)/N2(v = 0), Tv1, immediately after the discharge pulse. Both vibrational temperatures reached equilibrium within 100 μs after the discharge pulse by the vibration-to-vibration (V-V) process of N2-N2. The translational temperature was also measured using CARS. The rise in the translational temperature due to vibration-to-translation (V-T) energy transfer was not observed for a postdischarge time of 5 μs-1 ms in the dry-air discharge. However, when the air was humidified, a significant V-T energy transfer was observed. It was due to an extremely rapid V-T process of H2O-H2O following the V-V process of N2-H2O. Measurements showed that the humidification of the ambient air accelerated the decrease in the N2 vibrational temperature and increased the translational temperature. N2(v) was generated mostly in the secondary streamer, not in the primary one, according to estimation from the measured N2(v) density.

  5. Triggering Excimer Lasers by Photoionization from Corona Discharges

    Science.gov (United States)

    Xiong, Zhongmin; Duffey, Thomas; Brown, Daniel; Kushner, Mark

    2009-10-01

    High repetition rate ArF (192 nm) excimer lasers are used for photolithography sources in microelectronics fabrication. In highly attaching gas mixtures, preionization is critical to obtaining stable, reproducible glow discharges. Photoionization from a separate corona discharge is one technique for preionization which triggers the subsequent electron avalanche between the main electrodes. Photoionization triggering of an ArF excimer laser sustained in multi-atmosphere Ne/Ar/F2/Xe gas mixtures has been investigated using a 2-dimensional plasma hydrodynamics model including radiation transport. Continuity equations for charged and neutral species, and Poisson's equation are solved coincident with the electron temperature with transport coefficients obtained from solutions of Boltzmann's equation. Photoionizing radiation is produced by a surface discharge which propagates along a corona-bar located adjacent to the discharge electrodes. The consequences of pulse power waveform, corona bar location, capacitance and gas mixture on uniformity, symmetry and gain of the avalanche discharge will be discussed.

  6. Corona Discharges in Atmospheric Air Between a Wire and Two Plates

    OpenAIRE

    Bérard, Philippe; Lacoste, Deanna,; Laux, C.

    2011-01-01

    International audience; The corona discharge obtained in atmospheric air between a wire and two plates is presented. For the configuration studied and the voltage applied, the current is steady for the positive corona and exhibits Trichel pulses in the negative corona. The positive corona produces a homogeneous blue halo around the wire, whereas the negative discharge produces evenly spaced spots on the wire surface. We verified the analytic prediction that the ionic wind varies as the square...

  7. 120kV下常压空气纳秒脉冲电晕放电特性%Characteristic of nanosecond-pulsed corona discharge at 120 kV in atmospheric-pressure air

    Institute of Scientific and Technical Information of China (English)

    章程; 邵涛; 许家雨; 马浩; 徐蓉; 严萍

    2012-01-01

    With an excitation of negative repetitive pulses of 15 ns rise time and 30 to 40 ns duration, corona discharge in nanosecond-pulse regime at 120 kV in atmospheric-pressure air is experimentally investigated, and the characteristic of nanosecond-pulsed corona discharge is analyzed by the measurement of electrical discharge parameters, images and X-ray emission. The results show that X-ray emission occurs in nanosecond-pulsed corona discharge, but the intensity is weak. The counts of X rays decrease with the air gap spacing but increase with the pulse repetition frequency. In addition, owing to the fact that the residual particles in the gap enhance the local electric field when the next pulse is applied, separated corona channels are easily obtained at high pulse repetition frequency.%使用上升沿15 ns、脉宽30~40 ns的重复频率纳秒脉冲电源对120 kV下大气压空气中管-板电极结构电晕放电进行了实验研究,通过电压电流测量、放电图像拍摄和X射线探测分析了纳秒脉冲电晕放电特性.结果表明:纳秒脉冲电晕放电中存在X射线辐射,但辐射强度较弱,X射线辐射计数随着气隙距离的增大而减少,随着脉冲重复频率的增大而增多;放电空间的残余电荷加强了下一个脉冲到来时的局部电场,从而导致高重复频率下易于出现分散的电晕通道.

  8. Direct observation of laser guided corona discharges

    CERN Document Server

    Wang, Tie-Jun; Liu, Yaoxiang; Chen, Na; Liu, Yonghong; Ju, Jingjing; Sun, Haiyi; Wang, Cheng; Lu, Haihe; Liu, Jiansheng; Chin, See Leang; Li, Ruxin; Xu, Zhizhan

    2015-01-01

    Laser based lightning control holds a promising way to solve the problem of the long standing disaster of lightning strikes. But it is a challenging project due to insufficient understanding of the interaction between laser plasma channel and high voltage electric filed. In this work, a direct observation of laser guided corona discharge is reported. The high voltage corona discharge can be guided along laser plasma filament, and enhanced through the interaction with laser filaments. The fluorescence lifetime of laser filament guided corona discharge was measured to be several microseconds, which is 3 orders of magnitude longer than the fluorescence lifetime of laser filaments. This could be advantageous towards laser assisted leader development in the atmosphere.

  9. Detailed characteristics of intermittent current pulses due to positive corona

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yang, E-mail: liuyangwuh520@sina.com; Cui, Xiang; Lu, Tiebing; Wang, Zhenguo; Li, Xuebao; Xiang, Yu; Wang, Xiaobo [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China Electric Power University, Beijing 102206 (China)

    2014-08-15

    In order to get detailed characteristics of intermittent current pulses due to positive corona such as the repetition rate of burst-pulse trains, the peak value ratio of the primary pulse to the secondary pulse, the number of pulses per burst, and the interval of the secondary pulses, a systematic study was carried out in a coaxial conductor-cylinder electrode system with the conductor electrode being set with a discharge point. Empirical formulae for the number of pulses per burst and the interval of the secondary pulses are first presented. A theoretical model based on the motion of the space-charge clouds is proposed. Analysis with the model gives explanations to the experimental results and reveals some new insights into the physical mechanism of positive intermittent corona.

  10. Investigations on removal of SO2 from flue gas by aerosol formation in pulsed corona discharge process

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    The removal of SO2 from flue gas by pulsed coronadischarge in presence of ammonia was experimentally investigated.The results show that the SO2 removal mainly depend on thermalreaction of SO2 with NH3 and enhancement of 0%-25% by pulsed coronadischarge in the range of the specific energy 0-5 Wh/Nm3. Theaerosol mass concentration, mainly composed of ammonium sulfate,increases with specific energy dissipated into the reactor. With aninitial concentration of 2000-2100 ppmv SO2 and energy consumptionof 3 Wh/Nm3, when a stoichiometric amount of ammonia is injected,the removal efficiency of SO2 and percentage of ammonium sulfatesin reaction products are all ≥80%. The collection efficiency of thereactor for aerosol is about 74% at a flue gas temperature of 60 to65℃ and a water vapor content of 9% to 11% volume.

  11. Surface degradation of silicone rubber exposed to corona discharge

    OpenAIRE

    Zhu, Yong; Haji, Kenichi; Otsubo, Masahisa; Honda, Chikahisa

    2006-01-01

    This paper describes the surface degradation of unfilled high-temperature vulcanized silicone rubber (HTV-SR)###resulting from creeping corona discharges under atmospheric pressure. In this paper, HTV-SR specimens were exposed to corona###stress generated by a parallel needle-plate electrode system; furthermore, physicochemical analyses were conducted on the surface layer of SR before and after corona discharge treatment. The results showed that the plasma impingement from the corona discharg...

  12. CORONA DISCHARGE IGNITION FOR ADVANCED STATIONARY NATURAL GAS ENGINES

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Paul D. Ronney

    2003-09-12

    An ignition source was constructed that is capable of producing a pulsed corona discharge for the purpose of igniting mixtures in a test chamber. This corona generator is adaptable for use as the ignition source for one cylinder on a test engine. The first tests were performed in a cylindrical shaped chamber to study the characteristics of the corona and analyze various electrode geometries. Next a test chamber was constructed that closely represented the dimensions of the combustion chamber of the test engine at USC. Combustion tests were performed in this chamber and various electrode diameters and geometries were tested. The data acquisition and control system hardware for the USC engine lab was updated with new equipment. New software was also developed to perform the engine control and data acquisition functions. Work is underway to design a corona electrode that will fit in the new test engine and be capable igniting the mixture in one cylinder at first and eventually in all four cylinders. A test engine was purchased for the project that has two spark plug ports per cylinder. With this configuration it will be possible to switch between corona ignition and conventional spark plug ignition without making any mechanical modifications.

  13. TRIANGLE-SHAPED DC CORONA DISCHARGE DEVICE FOR MOLECULAR DECOMPOSITION

    Science.gov (United States)

    The paper discusses the evaluation of electrostatic DC corona discharge devices for the application of molecular decomposition. A point-to-plane geometry corona device with a rectangular cross section demonstrated low decomposition efficiencies in earlier experimental work. The n...

  14. Hydrogen Production from Methanol Using Corona Discharges

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Hydrogen production at room temperature from liquid methanol has been conductedusing corona discharge. The content of water in methanol solution has a significant effect on thisproduction. When water concentration increases from 1.0 % to 16.7 %, the methanol conversionrate changes from 0.196 to 0.284 mol/h. An important finding in this investigation is theformation of ethylene glycol as a major by-product. The yield of ethylene glycol is ranged from0.0045 to 0.0075 mol/h based on the water content.

  15. Monte Carlo simulation of electrical corona discharge in air

    Energy Technology Data Exchange (ETDEWEB)

    Settaouti, A.; Settaouti, L. [Electrotechnic Department, University of Sciences and Technology, P.O. Box 1505, El-M' naouar, Oran (Algeria)

    2011-01-15

    Electrical discharges play a key role in technologies; there are many industrial applications where the corona discharge is used. Air as insulator is probably the best compromise solution for many applications. All of this reflects on the great importance of the evaluation of the corona performance characteristics. Numerical simulation of the corona discharge helps to better understand the involved phenomena and optimize the corona devices. This paper is aimed at calculating the corona discharge in negative point-plane air gaps. To describe the non-equilibrium behavior of the electronic avalanches and to simulate the development of corona discharge the method of Monte Carlo has been used. This model provides the spatial-temporal local field and particles charged densities variations as well as the ionization front velocity. (author)

  16. Positive and negative pulsed corona in argon

    NARCIS (Netherlands)

    Veldhuizen, E.M. van; Rutgers, W.R.; Ebert, U.

    2002-01-01

    Photographs are obtained of corona discharges in argon at atmospheric pressure using a high resolution, intensified CCD camera. Positive and negative polarity is applied at the curved electrode in a point-plane gap and a plane-plane gap with a protruding point. Branching is observed in the positive

  17. Charging of moving surfaces by corona discharges sustained in air

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jun-Chieh, E-mail: junchwan@umich.edu; Kushner, Mark J., E-mail: mjkush@umich.edu [Department of Electrical Engineering and Computer Science, University of Michigan, 1301 Beal Ave., Ann Arbor, Michigan 48109-2122 (United States); Zhang, Daihua, E-mail: dhzhang@tju.edu.cn [Tianjin University, Tianjin (China); Leoni, Napoleon, E-mail: napoleon.j.leoni@hp.com; Birecki, Henryk, E-mail: henryk.birecki@hp.com; Gila, Omer, E-mail: omer-gila@hp.com [Hewlett-Packard Research Labs, Palo Alto, California 94304 (United States)

    2014-07-28

    Atmospheric pressure corona discharges are used in electrophotographic (EP) printing technologies for charging imaging surfaces such as photoconductors. A typical corona discharge consists of a wire (or wire array) biased with a few hundred volts of dc plus a few kV of ac voltage. An electric discharge is produced around the corona wire from which electrons drift towards and charge the underlying dielectric surface. The surface charging reduces the voltage drop across the gap between the corona wire and the dielectric surface, which then terminates the discharge, as in a dielectric barrier discharge. In printing applications, this underlying surface is continuously moving throughout the charging process. For example, previously charged surfaces, which had reduced the local electric field and terminated the local discharge, are translated out of the field of view and are replaced with uncharged surface. The uncharged surface produces a rebound in the electric field in the vicinity of the corona wire which in turn results in re-ignition of the discharge. The discharge, so reignited, is then asymmetric. We found that in the idealized corona charging system we investigated, a negatively dc biased corona blade with a dielectric covered ground electrode, the discharge is initially sustained by electron impact ionization from the bulk plasma and then dominated by ionization from sheath accelerated secondary electrons. Depending on the speed of the underlying surface, the periodic re-ignition of the discharge can produce an oscillatory charging pattern on the moving surface.

  18. Charging of moving surfaces by corona discharges sustained in air

    Science.gov (United States)

    Wang, Jun-Chieh; Zhang, Daihua; Leoni, Napoleon; Birecki, Henryk; Gila, Omer; Kushner, Mark J.

    2014-07-01

    Atmospheric pressure corona discharges are used in electrophotographic (EP) printing technologies for charging imaging surfaces such as photoconductors. A typical corona discharge consists of a wire (or wire array) biased with a few hundred volts of dc plus a few kV of ac voltage. An electric discharge is produced around the corona wire from which electrons drift towards and charge the underlying dielectric surface. The surface charging reduces the voltage drop across the gap between the corona wire and the dielectric surface, which then terminates the discharge, as in a dielectric barrier discharge. In printing applications, this underlying surface is continuously moving throughout the charging process. For example, previously charged surfaces, which had reduced the local electric field and terminated the local discharge, are translated out of the field of view and are replaced with uncharged surface. The uncharged surface produces a rebound in the electric field in the vicinity of the corona wire which in turn results in re-ignition of the discharge. The discharge, so reignited, is then asymmetric. We found that in the idealized corona charging system we investigated, a negatively dc biased corona blade with a dielectric covered ground electrode, the discharge is initially sustained by electron impact ionization from the bulk plasma and then dominated by ionization from sheath accelerated secondary electrons. Depending on the speed of the underlying surface, the periodic re-ignition of the discharge can produce an oscillatory charging pattern on the moving surface.

  19. Discharge pulse phenomenology

    Science.gov (United States)

    Frederickson, A. R.

    1985-01-01

    A model was developed which places radiation induced discharge pulse results into a unified conceptual framework. Only two phenomena are required to interpret all space and laboratory results: (1) radiation produces large electrostatic fields inside insulators via the trapping of a net space charge density; and (2) the electrostatic fields initiate discharge streamer plasmas similar to those investigated in high voltage electrical insulation materials; these streamer plasmas generate the pulsing phenomena. The apparent variability and diversity of results seen is an inherent feature of the plasma streamer mechanism acting in the electric fields which is created by irradiation of the dielectrics. The implications of the model are extensive and lead to constraints over what can be done about spacecraft pulsing.

  20. Removal of 2,4-dichlorophenoxyacetic acid in aqueous solution by pulsed corona discharge treatment: Effect of different water constituents, degradation pathway and toxicity assay.

    Science.gov (United States)

    Singh, Raj Kamal; Philip, Ligy; Ramanujam, Sarathi

    2017-10-01

    A multiple pin-plane corona discharge reactor was used to generate plasma for the degradation of 2,4 dichlorophenoxyacetic acid (2,4-D) from the aqueous solution. The 2,4-D of concentration 1 mg/L was completely removed within 6 min of plasma treatment. Almost complete mineralization was achieved after the treatment time of 14 min for a 2,4-D concentration of 10 mg/L. Effects of different water constituents such as carbonates, nitrate, sulphate, chloride ions, natural organic matter (humic acids) and pH on 2,4-D degradation was studied. A significant antagonistic effect of carbonate and humic acid was observed, whereas, the effects of other ions were insignificant. A higher first order rate constant of 1.73 min(-1) was observed, which was significantly decreased in the presence of carbonate ions and humic acids. Also, a higher degradation of 2,4-D was observed in acidic pH conditions. Different 2,4-D intermediates were detected and the degradation pathway of 2,4-D in plasma treatment process was suggested. The toxicity of 10 mg/L 2,4-D was completely eradicated after 10 min of plasma treatment. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Capacitor discharge pulse analysis.

    Energy Technology Data Exchange (ETDEWEB)

    Baker, Michael Sean; Griffiths, Stewart K.; Tanner, Danelle Mary

    2013-08-01

    Capacitors used in firing sets and other high discharge current applications are discharge tested to verify performance of the capacitor against the application requirements. Parameters such as capacitance, inductance, rise time, pulse width, peak current and current reversal must be verified to ensure that the capacitor will meet the application needs. This report summarizes an analysis performed on the discharge current data to extract these parameters by fitting a second-order system model to the discharge data and using this fit to determine the resulting performance metrics. Details of the theory and implementation are presented. Using the best-fit second-order system model to extract these metrics results in less sensitivity to noise in the measured data and allows for direct extraction of the total series resistance, inductance, and capacitance.

  2. Acoustic field effects on a negative corona discharge

    Science.gov (United States)

    Bálek, R.; Červenka, M.; Pekárek, S.

    2014-06-01

    For a negative corona discharge under atmospheric pressure in different regimes, we investigated the effects of an acoustic field both on its electrical parameters and on the change in its visual appearance. We found that the application of an acoustic field on the true corona discharge, for particular currents, decreases the discharge voltage. The application of an acoustic field on the discharge in the filamentary streamer regime substantially extends the range of currents for which the discharge voltage remains more or less constant, i.e. it allows a substantial increase in the power delivered to the discharge. The application of an acoustic field on the discharge causes the discharge to spread within the discharge chamber and consequently, a highly reactive non-equilibrium plasma is created throughout the inter-electrode space. Finally, our experimental apparatus radiates almost no acoustic energy from the discharge chamber.

  3. Negative DC corona discharge current characteristics in a flowing two-phase (air + suspended smoke particles) fluid

    Science.gov (United States)

    Berendt, Artur; Domaszka, Magdalena; Mizeraczyk, Jerzy

    2017-04-01

    The electrical characteristics of a steady-state negative DC corona discharge in a two-phase fluid (air with suspended cigarette smoke particles) flowing along a chamber with a needle-to-plate electrode arrangement were experimentally investigated. The two-phase flow was transverse in respect to the needle-to-plate axis. The velocity of the transverse two-phase flow was limited to 0.8 m/s, typical of the electrostatic precipitators. We found that three discharge current modes of the negative corona exist in the two-phase (air + smoke particles) fluid: the Trichel pulses mode, the "Trichel pulses superimposed on DC component" mode and the DC component mode, similarly as in the corona discharge in air (a single-phase fluid). The shape of Trichel pulses in the air + suspended particles fluid is similar to that in air. However, the Trichel pulse amplitudes are higher than those in "pure" air while their repetition frequency is lower. As a net consequence of that the averaged corona discharge current in the two-phase fluid is lower than in "pure" air. It was also found that the average discharge current decreases with increasing suspended particle concentration. The calculations showed that the dependence of the average negative corona current (which is a macroscopic corona discharge parameter) on the particle concentration can be explained by the particle-concentration dependencies of the electric charge of Trichel pulse and the repetition frequency of Trichel pulses, both giving a microscopic insight into the electrical phenomena in the negative corona discharge. Our investigations showed also that the average corona discharge current in the two-phase fluid is almost unaffected by the transverse fluid flow up to a velocity of 0.8 m/s. Contribution to the topical issue "The 15th International Symposium on High Pressure Low Temperature Plasma Chemistry (HAKONE XV)", edited by Nicolas Gherardi and Tomáš Hoder

  4. Numerical Simulation of Nanosecond-Pulse Electrical Discharges

    Science.gov (United States)

    2012-01-01

    were rst investigated.1,2 Activity in the research area waned in the 1970s, with some work on drag reduction using corona discharges appearing in...Aleksandrov et al.38 suggest that in nanosecond pulse discharges at atmospheric pressure at very high values of the reduced electric eld, E=N 1000 Td... atmospheric pressure is of the order of 100 m, which corresponds to an acoustic time of acoustic 0:3 s. Thus, nanosecond-pulse discharge energy

  5. Simulation of low temperature atmospheric pressure corona discharge in helium

    Science.gov (United States)

    Bekasov, Vladimir; Kirsanov, Gennady; Eliseev, Stepan; Kudryavtsev, Anatoly; Sisoev, Sergey

    2015-11-01

    The main objective of this work was to construct a numerical model of corona discharge in helium at atmospheric pressure. The calculation was based on the two-dimensional hybrid model. Two different plasma-chemical models were considered. Models were built for RF corona and negative DC corona discharge. The system of equations is solved by the finite element method in the COMSOL Multiphysics. Main parameters of the discharge (the density of charged and excited particles, the electron temperature) and their dependence on the input parameters of the model (geometry, electrode voltage, power) were calculated. The calculations showed that the shape of the electron distribution near the electrode depends on the discharge power. The neutral gas heating data obtained will allow predicting the temperature of the gases at the designing of atmospheric pressure helium plasma sources.

  6. Branch Structure of Corona Discharge:Experimental Simulation and Chemical Properties

    Institute of Scientific and Technical Information of China (English)

    邹吉军; 刘昌俊

    2004-01-01

    The branch structure of corona discharge has been investigated via C2H2 corona discharge. Carbon filament with excellent branch structure is formed in the discharge. This carbon filament offers a direct mimic of the branch structure of corona discharge. It providesa very useful way to study on the average energy, physical and chemical characteristics of coronadischarge. On this basis, the chemical property of corona discharge for methane conversion is discussed.

  7. DBD-Corona Discharge for Degradation of Toxic Gases

    Institute of Scientific and Technical Information of China (English)

    M.PACHECO-PACHECO; J.PACHECO-SOTELO; H.MORENO-SAAVEDRA; J.A.DIAZ-GOMEZ; A.MERCADO-CABRERA; M.YOUSFI

    2007-01-01

    The non-thermal plasma technology is a promising technique to treat SO2 and NOx.Chemical radicals produced with this technology can remove several pollutants at atmospheric pressure in a very short period of time simultaneously.Both theoretical and experimental study on SO2 and NOx removal,by a dielectric barrier discharge (DBD) with corona effect,is presented.

  8. Optical emission spectroscopy of point-plane corona and back-corona discharges in air

    Science.gov (United States)

    Czech, T.; Sobczyk, A. T.; Jaworek, A.

    2011-12-01

    Results of spectroscopic investigations and current-voltage characteristics of corona discharge and back discharge on fly-ash layer, generated in point-plane electrode geometry in air at atmospheric pressure are presented in the paper. The characteristics of both discharges are similar but differ in the current and voltage ranges of all the discharge forms distinguished during the experiments. Three forms of back discharge, for positive and negative polarity, were investigated: glow, streamer and low-current back-arc. In order to characterize ionisation and excitation processes in back discharge, the emission spectra were measured and compared with those obtained for normal corona discharge generated in the same electrode configuration but with fly ash layer removed. The emission spectra were measured in two discharge zones: near the tip of needle electrode and near the plate. Visual forms of the discharge were recorded with digital camera and referred to current-voltage characteristics and emission spectra. The measurements have shown that spectral lines emitted by back discharge depend on the form of discharge and the discharge current. From the comparison of the spectral lines of back and normal discharges an effect of fly ash layer on the discharge morphology can be determined. The recorded emission spectra formed by ionised gas and plasma near the needle electrode and fly ash layer are different. It should be noted that in back arc emission, spectral lines of fly ash layer components can be distinguished. On the other hand, in needle zone, the emission of high intensity N2 second positive system and NO γ lines can be noticed. Regardless of these gaseous lines, also atomic lines of dust layer were present in the spectrum. The differences in spectra of back discharge for positive and negative polarities of the needle electrode have been explained by considering the kind of ions generated in the crater in fly ash layer. The aim of these studies is to better

  9. Numerical simulation transient electron distribution of direct current negative corona discharge in air

    Science.gov (United States)

    Liu, Xinghua; Xian, Richang; Yu, Peng; Pei, Ying; Lv, Xuebin; Sun, Xuefeng; Wang, Tao; Ning, Shangyuan; Wang, Shikun

    2017-05-01

    In order to explore the characteristics of electron in DC negative corona discharge, microcosmic process of negative corona discharge in air is simulated in this paper. The numerical computation is established with a bar-plate electrode configuration with an inter-electrode gap of 3.3 mm, the negative DC voltage applied to the bar is 5.0 kV, the pressure in air discharge is fixed at 1.0 atm, and the gas temperature is assumed to be a constant (300 K). By solution the system of electron conservation equation, the electron mean energy conservation, the heavy species multi-component diffusion transport equation, and the Poisson’s equation, characteristics of electrons (electron mean energy, electron density, and generation and dissipation performances of electrons) at 6 representative time points during a pulse are obtained and then discussed emphatically.

  10. Development of Efficient Models of Corona Discharges Around Tall Structures

    Science.gov (United States)

    Tucker, J.; Pasko, V. P.

    2012-12-01

    This work concerns with numerical modeling of glow corona and sreamer corona discharges that occur near tall ground structures under thunderstorm conditions. Glow corona can occur when ambient electric field reaches modest values on the order of 0.2 kV/cm and when the electric field near sharp points of ground structure rises above a geometry dependent critical field required for ionization of air. Air is continuously ionized in a small region close to the surface of the structure and ions diffuse out into the surrounding air forming a corona. A downward leader approaching from a thundercloud causes a further increase in the electric field at the ground level. If the electric field rises to the point where it can support formation of streamers in air surrounding the tall structure, a streamer corona flash, or series of streamer corona flashes can be formed significantly affecting the space charge configuration formed by the preceding glow corona. The streamer corona can heat the surrounding air enough to form a self-propagating thermalized leader that is launched upward from the tall structure. This leader travels upward towards the thundercloud and connects with the downward approaching leader thus causing a lightning flash. Accurate time-dependent modeling of charge configuration created by the glow and streamer corona discharges around tall structure is an important component for understanding of the sequence of events leading to lightning attachment to the tall structure. The present work builds on principal modeling ideas developed previously in [Aleksandrov et al., J. Phys. D: Appl. Phys., 38, 1225, 2005; Bazelyan et al., Plasma Sources Sci. Technol., 17, 024015, 2008; Kowalski, E. J., Honors Thesis, Penn State Univ., University Park, PA, May 2008; Tucker and Pasko, NSF EE REU Penn State Annual Res. J., 10, 13, 2012]. The non-stationary glow and streamer coronas are modeled in spherical geometry up to the point of initiation of the upward leader. The model

  11. Improvement of aluminum/polyethylene adhesion through corona discharge

    Science.gov (United States)

    Popelka, Anton; Krupa, Igor; Novák, Igor; Al-Maadeed, Mariam Ali S. A.; Ouederni, Mabrouk

    2017-01-01

    Polyethylene (PE) is often used in several industrial applications including the building, packaging and transport industries. Aluminum (Al) is widely used in different applications in the automotive, railway, aeronautic, and naval industries because of its excellent mechanical and chemical properties. Laminates prepared from Al and PE lead to an enhancement in physical and mechanical properties. These materials play a main role in the packaging and building sectors, such as in TetraPak containers and aluminum composite panels. The main problem observed is associated with the adhesion between polymers and metals. This research focused on investigating the enhancement in the adhesion of the PE/Al laminate using the corona discharge. The corona treatment of the surfaces led to a significant increase in the adhesion of the PE/Al laminate as a result of improved surface properties confirmed by peel test measurements. Moreover, the positive effect of the corona treatment in combination with a primer on the improvement of adhesion characteristics was observed too. Different analytical techniques were employed to characterize the effect of the corona treatment on the improvement in adhesion of PE/Al. A significant increase in wettability was confirmed by the measurement of contact angles. Changes in the surface morphology of the PE and Al surface, after the corona treatments at different operating conditions, were observed using atomic force microscopy (AFM) and scanning electron microscopy (SEM). In addition, x-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) were used to analyze changes in chemical composition after the corona discharge effect on PE and Al surfaces.

  12. Study of the impact of photoionization on negative and positive needle-plane corona discharge in atmospheric air

    Science.gov (United States)

    Dordizadeh, Peyman; Adamiak, Kazimierz; Castle, G. S. Peter

    2016-12-01

    A 2D axisymmetric model of the atmospheric pressure needle-plane corona discharge incorporating the photoionization phenomenon is presented in this paper. The photoionization model was developed using a three-term exponential approximation based on a model suggested by Bourdon et al. The coefficients of the photoionization model were tuned by reproducing the results of a positive corona discharge and comparing them with the experimental data published previously in the literature. In fact, this photoionization model is an essential module for studying a self-sustained positive corona discharge. Incorporating the photoionization phenomenon in the numerical model for the negative corona discharge causes an average of 5% increase in both the frequency and the DC current of the discharge. The relative importance of the photoionization in both positive and negative coronas was put in a quantitative frame by introducing the ratio of the integral of the impact ionization source term (IIS) divided by the Integral of the photoionization source term (IPS). With the help of this ratio and the spatial distribution of the two source terms, the minor role played by the photoionization source term for the negative discharge is justified. In the case of the positive discharge, the vital importance of the photoionization for sustaining the discharge is explained. Moreover, for the negative corona discharge, comparison of the ratio of the secondary emitted electrons (SEE) from the cathode surface divided by the IPS, at different instants of the formation of a Trichel pulse was found to be beneficial for the purpose of evaluating the relative importance of the photoionization. It is concluded that, although SEE on the rising edge of the Trichel pulse is smaller than the IPS since the injected electrons from the cathode surface are generated in the area with the strongest electric field, they have a greater contribution to the discharge current.

  13. The characteristics of a negative corona discharge in He/Xe/SF6 mixture

    Science.gov (United States)

    Shuaibov, A. K.

    1999-02-01

    The results of investigation of the electrical and optical characteristics of a negative corona discharge in the electrode system of the type needle-grid lit in a He/Xe/SF6 mixture under the pressure of 100-300 kPa are presented in this paper. The given medium is working for a pulse-periodic excimer lamp on = 351 nm XeF(B-X). Distributed on the length of a lamp active media a bipolar corona discharge is intended for using in the electric circulation of the XeF-lamp working medium. It is shown that the given discharge is ignited steadily in the He/Xe/SF6 mixture, containing 0, 5kPa SF6 molecules and is characterised by a low power consumption; the current of the discharge is limited to the development of instability by increasing the voltage on the needles; in hot zones of corona discharge SF6 molecules cause the effective population 6s of XeI state.

  14. Investigation of Nanosecond Pulsed Discharge and Its Audio Characteristics in Atmospheric-pressure Air

    Institute of Scientific and Technical Information of China (English)

    REN Chengyan; RAN Huijuan; WANG Jue; WANG Tao; YAN Ping

    2013-01-01

    There was no well-resolved mechanism of audible noise caused by corona discharge on UHV transmission lines.Hence we measured the sound pressure of pulsed discharges between needle-plane electrodes under different discharge conditions in air,for revealing the intrinsic relationship between discharge and its audible noise(AN).The relationship between discharge parameters and audio characteristics was drawn from the analysis of the electric and sound signals obtained in experiments.Experiment results showed that nanosecond pulsed discharges produce the sound pressure with a microsecond pulse lagging behind the discharge pulse in their waveforms.The peak value of the sound pulse decreases and its high frequency component gradually attenuates,when the measuring distance from discharges increases.The sound pulses correlate with the discharge current and voltage significantly,especially the current.The audible noise produced by repetitive pulsed discharge increases with the strength,duration,and pulse repetition rate of discharge.

  15. Hydrogen production from dimethyl ether using corona discharge plasma

    Science.gov (United States)

    Zou, Ji-Jun; Zhang, Yue-Ping; Liu, Chang-Jun

    Dimethyl ether (DME), with its non-toxic character, high H/C ratio and high-energy volumetric density, is an ideal resource for hydrogen production. In this work, hydrogen production from the decomposition of DME using corona discharge has been studied. The corona discharge plasma decomposition was conducted at ambient conditions. The effects of dilution gas (argon), flow rate, frequency and waveforms on the DME decomposition were investigated. The addition of dilution gas can significantly increase the hydrogen production rate. The highest hydrogen production rate with the lowest energy consumption presents at the flow rate of 27.5 Nml min -1. AC voltage is more favored than DC voltage for the production of hydrogen with less energy input. The optimal frequency is 2.0 kHz. The hydrogen production rate is also affected by the input waveform and decreases as following: sinusoid triangular > sinusoid > ramp > square, whereas the sinusoid waveform shows the highest energy efficiency. The corona discharge decomposition of DME is leading to a simple, easy and convenient hydrogen production with no needs of catalyst and external heating.

  16. Model of Ozone Production in the DC Corona Discharge

    Science.gov (United States)

    Chen, Junhong; Davidson, Jane

    2002-10-01

    A comprehensive numerical model of ozone production in clean, dry air by DC corona discharges is presented. This model combines a first-principle corona plasma model with a chemistry and 2-D transport model to obtain the distributions of ozone and other gaseous products in the neighborhood of a corona discharge wire. Electron number density distribution is obtained by solving the continuity equations for electrons and ions and the simplified Maxwell's equation. The non-Maxwellian electron energy distribution is solved from the Boltzmann equation. The chemical kinetics of ozone formation and destruction are based on recent atmospheric chemistry models taking into account the contributions of excited molecules. The transport model includes the conservation equations for total mass, momentum, energy and the mass of individual species and is solved using FLUENT. The predicted ozone production rate agrees well with experimental data. Excited molecules contribute more than 80 percent of the total ozone produced. The effects of discharge polarity, current, wire radius, air temperature, and air velocity (residence time) on the production of ozone are discussed.

  17. Evaluation of energy transfer and utilization efficiency of azo dye removal by different pulsed electrical discharge modes

    Institute of Scientific and Technical Information of China (English)

    SHEN YongJun; LEI LeCheng; ZHANG XingWang

    2008-01-01

    The degradation of an azo dye, acid orange 7 (AO7), caused by different high voltage pulsed electrical discharge modes (spark, streamer and corona discharge) induced by the various initial conductivities was investigated. A new type of pulsed high voltage source with thyratron switch and Blumlein pulse forming net (BPFN) was used. The typical discharge waveforms of voltage, current, power, pulse en-ergy and the pictures of spark, streamer and corona discharge modes were presented. The results in-dicated that pulsed electrical discharges led to complete decolorization and substantial decrease of the chemical oxygen demand (COD) of the dye solution. The main intermediate products were monitored by GC-MS. The discharge modes changed from spark to streamer and to corona discharge, and the streamer length decreased with the liquid conductivity increasing. At a constant input power, the peak voltage, peak current, peak power and energy per pulse of the three discharge modes ranked in the following order: spark > streamer > corona. The effective energy transfer efficiency of AO7 removal was higher for spark discharge (57.2%) than for streamer discharge (40.4%) and corona discharge (27.6%). Moreover, the energy utilization efficiency of AO7 removal for spark discharge was 1.035×109 mol/J, and for streamer and corona discharge they were 0.646×10-8 and 0.589×10-9mol/J. Both the energy transfer efficiency and the energy utilization efficiency of spark discharge were the highest.

  18. Streptococci biofilm decontamination on teeth by low-temperature air plasma of dc corona discharges

    Science.gov (United States)

    Kovalóvá, Z.; Zahoran, M.; Zahoranová, A.; Machala, Z.

    2014-06-01

    Non-thermal plasmas of atmospheric pressure air direct current corona discharges were investigated for potential applications in dental medicine. The objective of this ex vivo study was to apply cold plasmas for the decontamination of Streptococci biofilm grown on extracted human teeth, and to estimate their antimicrobial efficiency and the plasma's impact on the enamel and dentine of the treated tooth surfaces. The results show that both positive streamer and negative Trichel pulse coronas can reduce bacterial population in the biofilm by up to 3 logs in a 10 min exposure time. This bactericidal effect can be reached faster (within 5 min) by electrostatic spraying of water through the discharge onto the treated tooth surface. Examination of the tooth surface after plasma exposure by infrared spectroscopy and scanning electron microscopy did not show any significant alteration in the tooth material composition or the tooth surface structures.

  19. Semi-analytical modelling of positive corona discharge in air

    Science.gov (United States)

    Pontiga, Francisco; Yanallah, Khelifa; Chen, Junhong

    2013-09-01

    Semianalytical approximate solutions of the spatial distribution of electric field and electron and ion densities have been obtained by solving Poisson's equations and the continuity equations for the charged species along the Laplacian field lines. The need to iterate for the correct value of space charge on the corona electrode has been eliminated by using the corona current distribution over the grounded plane derived by Deutsch, which predicts a cos m θ law similar to Warburg's law. Based on the results of the approximated model, a parametric study of the influence of gas pressure, the corona wire radius, and the inter-electrode wire-plate separation has been carried out. Also, the approximate solutions of the electron number density has been combined with a simplified plasma chemistry model in order to compute the ozone density generated by the corona discharge in the presence of a gas flow. This work was supported by the Consejeria de Innovacion, Ciencia y Empresa (Junta de Andalucia) and by the Ministerio de Ciencia e Innovacion, Spain, within the European Regional Development Fund contracts FQM-4983 and FIS2011-25161.

  20. Pulsed discharge production Ar* metastables

    Science.gov (United States)

    Han, Jiande; Heaven, Michael C.; Emmons, Daniel; Perram, Glen P.; Weeks, David E.; Bailey, William F.

    2016-03-01

    The production of relatively high densities of Ar* metastables (>1012 cm-3) in Ar/He mixtures, at total pressures close to 1 atm, is essential for the efficient operation of an optically pumped Ar* laser. We have used emission spectroscopy and diode laser absorption spectroscopy measurements to observe the production and decay of Ar* in a parallel plate pulsed discharge. With discharge pulses of 1 μs duration we find that metastable production is dominated by processes occurring within the first 100 ns of the gas break-down. Application of multiple, closely spaced discharge pulses yields insights concerning conditions that favor metastable production. This information has been combined with time-resolved measurements of voltage and current. The experimental results and preliminary modeling of the discharge kinetics are presented.

  1. ZnO Nanowire-Based Corona Discharge Devices Operated Under Hundreds of Volts

    OpenAIRE

    Yang, Wenming; Zhu, Rong; Zong, Xianli

    2016-01-01

    Minimizing the voltage of corona discharges, especially when using nanomaterials, has been of great interest in the past decade or so. In this paper, we report a new corona discharge device by using ZnO nanowires operated in atmospheric air to realize continuous corona discharge excited by hundreds of volts. ZnO nanowires were synthesized on microelectrodes using electric-field-assisted wet chemical method, and a thin tungsten film was deposited on the microchip to enhance discharging perform...

  2. Vortex focusing of ions produced in corona discharge.

    Science.gov (United States)

    Kolomiets, Yuri N; Pervukhin, Viktor V

    2013-06-15

    Completeness of the ion transportation into an analytical path defines the efficiency of ionization analysis techniques. This is of particular importance for atmospheric pressure ionization sources like corona discharge, electrospray, ionization with radioactive ((3)H, (63)Ni) isotopes that produce nonuniform spatial distribution of sample ions. The available methods of sample ion focusing are either efficient at reduced pressure (~1Torr) or feature high sample losses. This paper deals with experimental research into atmospheric pressure focusing of unipolar (positive) ions using a highly swirled air stream with a well-defined vortex core. Effects of electrical fields from corona needle and inlet capillary of mass spectrometer on collection efficiency is considered. We used a corona discharge to produce an ionized unipolar sample. It is shown experimentally that with an electrical field barrier efficient transportation and focusing of an ionized sample are possible only when a metal plate restricting the stream and provided with an opening covered with a grid is used. This gives a five-fold increase of the transportation efficiency. It is shown that the electric field barrier in the vortex sampling region reduces the efficiency of remote ionized sample transportation two times. The difference in the efficiency of light ion focusing observed may be explained by a high mobility and a significant effect of the electric field barrier upon them. It is possible to conclude based on the experimental data that the presence of the field barrier narrows considerably (more than by one and half) the region of the vortex sample ion focusing.

  3. Corona discharges from a windmill and its lightning protection tower in winter thunderstorms

    Science.gov (United States)

    Wu, Ting; Wang, Daohong; Rison, William; Thomas, Ronald J.; Edens, Harald E.; Takagi, Nobuyuki; Krehbiel, Paul R.

    2017-05-01

    This paper presents lightning mapping array (LMA) observations of corona discharges from a windmill and its lightning protection tower in winter thunderstorms in Japan. Corona discharges from the windmill, called windmill coronas, and those from the tower, called tower coronas, are distinctly different. Windmill coronas occur with periodic bursts, generally radiate larger power, and possibly develop to higher altitudes than tower coronas do. A strong negative electric field is necessary for the frequent production of tower coronas but is not apparently related with windmill coronas. These differences are due to the periodic rotation of the windmill and the moving blades which can escape space charges produced by corona discharges and sustain a large local electric field. The production period of windmill coronas is related with the rotation period of the windmill. Surprisingly, for one rotation of the windmill, only two out of the three blades produce detectable discharges and source powers of discharges from these two blades are different. The reason for this phenomenon is still unclear. For tower coronas, the source rate can get very high only when there is a strong negative electric field, and the source power can get very high only when the source rate is very low. The relationship between corona discharges and lightning flashes is investigated. There is no direct evidence that corona discharges can increase the chance of upward leader initiation, but nearby lightning flashes can increase the source rate of corona discharges right after the flashes. The peak of the source height distribution of corona discharges is about 100 m higher than the top of the windmill and the top of the tower. Possible reasons for this result are discussed.

  4. Mechanism for negative corona current pulse in CO sub 2 -SF sub 6 mixtures

    CERN Document Server

    Zahoranova, A; Simor, M; Cernak, M

    2003-01-01

    Current waveforms of first negative corona pulses have been measured in CO sub 2 -SF sub 6 mixtures over a pressure range extending from 6.65 to 50 kPa and various overvoltages. Effects of changing cathode secondary electron emission were studied using a copper cathode coated by CuI and graphite. For a given set of experimental conditions it is concluded that in the mixtures containing up to 30% of SF sub 6 the negative corona pulse is associated with the formation of a cathode-directed streamer-like ionizing wave in the immediate vicinity of the cathode. This is in contrast to the discharge behaviour in air-SF sub 6 and N sub 2 -SF sub 6 mixtures, where in similar conditions the discharge develops according to a multi-avalanche Townsend mechanism. (rapid communication)

  5. Corona discharge ion mobility spectrometry at reduced pressures

    Science.gov (United States)

    Tabrizchi, Mahmoud; Rouholahnejad, Fereshteh

    2004-11-01

    Ion mobility spectrometers (IMSs) normally operate at ambient pressure. In this work an IMS cell has been designed and constructed to allow the pressure to be reduced inside the IMS cell. In this cell, corona discharge was employed as the ionization source. Reducing pressure affected both the discharge and the performance of the IMS. The discharge current was observed to increase with reducing pressure while the ignition potential decreased. The ion current received at the collector plate was also increased about 50 times when the pressure was reduced from ambient pressure to 15 Torr. The higher ion current can lead to an extended dynamic range. IMS spectra were recorded at various pressures and the results show that the drift times shift perfectly linear with pressure. This suggests that unlike temperature, pressure correction for ion mobility spectra is as simple as multiplying the drift times by a factor of 760/P.

  6. 线-板式脉冲电晕放电反应器的发射光谱研究%Study of a Wire-to-Plate Positive Pulsed Corona Discharge Reactor by Emission Spectroscopy

    Institute of Scientific and Technical Information of China (English)

    王沈兵; 骆仲泱; 赵磊; 轩俭勇; 江建平; 岑可法

    2011-01-01

    以发射光谱法为基础,检测了常压状态线-板式脉冲电晕放电过程OH自由基在反应器内的空间分布;研究了线电极直径,线线间距以及线板间距对生成OH自由基的影响;从而明确脉冲电晕放电反应器的性能.结果显示:OH自由基浓度沿线电极X轴方向逐渐降低,活化区域半径20 mm左右,沿Y轴方向先升高后降低,活化区域半径大于30 mm;线电极的直径小于2mm时,OH自由基的光谱强度基本不变,线电极直径继续增大,发射光谱强度随之迅速下降.线线间距逐渐增大,OH自由基的发射光谱强度随之增强.OH自由基的发射光谱强度随着线板间距的增大而降低.%In order to get extensive knowledge of wire-to-plate pulsed corona discharge reactor, the influences of different diameters of wire electrode, different wire-to-plate and wire-to-wire spacing on OH radical generation were experimentally investigated under atmospheric pressure based on emission spectrum, and the spatial distribution of OH radicals in the electric field was also discussed in detail. The results showed that OH radicals decrease along the X-axis, and the activation radius is approximately 20 mm; showing a trend of first increase and then decrease along the Y-axis, with the activation radius being more than 30 mm. OH radical has small change as the diameter of wire electrode changes below 2 mm, with a sharp decline as the diameter continues to increase. OH radical emission intensity increases as wire-to-wire spacing increases and decrease as wire-to-plate spacing increases.

  7. Naphthalene decomposition in a DC corona radical shower discharge

    Institute of Scientific and Technical Information of China (English)

    Ming-jiang NI; Xu SHEN; Xiang GAO; Zu-liang WU; Hao LU; Zhong-shan LI; Zhong-yang LUO; Ke-fa CEN

    2011-01-01

    The naphthalene decomposition in a corona radical shower discharge (CRS) was investigated, with attention paid to the influences of voltage and initial naphthalene density. The OH emission spectra were investigated so as to know the naphthalene decomposing process. The by-products were analyzed and a decomposing theory in discharge was proposed. The results showed that higher voltage and relative humidity were effective on decomposition. The initial concentration affected the decomposing efficiency of naphthalene. When the mitial naphthalene density was 17 mg/m3, the decomposition rate was found to be 70% under 14 kV. The main by-products were carbon dioxide and water. However, a small amount of carbonic oxide, 1, 2-ethanediol and acetaldehyde were found due to the incomplete oxidization.

  8. Experimental Research on the Characteristics of Corona Discharge%电晕放电若干特性的实验研究

    Institute of Scientific and Technical Information of China (English)

    原青云; 孙永卫; 张希军; 周为平

    2011-01-01

    为研究空中带高压物体的电晕放电辐射信号特征,采用组建的静电放电测试系统对电晕电流及其辐射信号进行了实验研究.实验表明:电晕放电脉冲波形具有明显的极性效应.负极性下先发生电晕放电,且电流波形的上升时间小于正电晕电流;电晕放电信号波形前沿陡峭,上升时间从几个ns到二十几个ns;电晕放电辐射信号的频谱成钟型连续谱,其频率范围主要集中在20~100 MHz之间;极性不同,电晕放电辐射信号波形不同,并且正电晕信号幅值高于负电晕信号幅值.%In order to study the characteristics of signals radiated from corona discharge from high-voltage object in the air, the experimental research on the characteristics of corona current and signal radiated from corona discharge is carried out using the electrostatic discharge testing system. The experiment shows that: firstly, the corona discharge pulse waveforms have an obvious polarity effect;negative corona discharge occurs first and the pulse amplitude is shorter than that of positive corona; the rising time of pulse waveform of negative corona current is smaller than that of positive corona current. Secondly,the waveform of signal radiated from corona discharge has a steep rising edge;the rising time is from several ns to a score of ns. Thirdly,the spectrum of signal radiated from corona discharge is continual spectrum, whose frequency range is from 20 MHz to 100 MHz. Finally when the polarity is different,the waveform of signal radiated from corona discharge is different and the amplitude of signal of positive corona is higher than that of negative corona.

  9. Corona discharge ionization of paracetamol molecule: Peak assignment

    Science.gov (United States)

    Bahrami, H.; Farrokhpour, H.

    2015-01-01

    Ionization of paracetamol was investigated using ion mobility spectrometry equipped with a corona discharge ionization source. The measurements were performed in the positive ion mode and three peaks were observed in the ion mobility spectrum. Experimental evidence and theoretical calculations were used to correlate the peaks to related ionic species of paracetamol. Two peaks were attributed to protonated isomers of paracetamol and the other peak was attributed to paracetamol fragment ions formed by dissociation of the N-C bond after protonation of the nitrogen atom. It was observed that three sites of paracetamol compete for protonation and their relative intensities, depending on the sample concentration. The ratio of ion products could be predicted from the internal proton affinity of the protonation sites at each concentration.

  10. A corona discharge initiated electrochemical electrospray ionization technique.

    Science.gov (United States)

    Lloyd, John R; Hess, Sonja

    2009-11-01

    We report here the development of a corona discharge (CD) initiated electrochemical (EC) electrospray ionization (ESI) technique using a standard electrospray ion source. This is a new ionization technique distinct from ESI, electrochemistry inherent to ESI, APCI, and techniques using hydroxyl radicals produced under atmospheric pressure conditions. By maximizing the observable CD at the tip of a stainless steel ESI capillary, efficient electrochemical oxidation of electrochemically active compounds is observed. For electrochemical oxidation to be observed, the ionization potential of the analyte must be lower than Fe. Ferrocene labeled compounds were chosen as the electrochemically active moiety. The electrochemical cell in the ESI source was robust, and generated ions with selectivity according to the ionization potential of the analytes and up to zeptomolar sensitivity. Our results indicate that CD initiated electrochemical ionization has the potential to become a powerful technique to increase the dynamic range, sensitivity, and selectivity of ESI experiments.

  11. DC negative corona discharge in atmospheric pressure helium: transition from the corona to the ‘normal’ glow regime

    Science.gov (United States)

    Hasan, Nusair; Antao, Dion S.; Farouk, Bakhtier

    2014-06-01

    Direct current (dc) negative corona discharges in atmospheric pressure helium are simulated via detailed numerical modeling. Simulations are conducted to characterize the discharges in atmospheric helium for a pin plate electrode configuration. A self-consistent two-dimensional hybrid model is developed to simulate the discharges and the model predictions are validated with experimental measurements. The discharge model considered consists of momentum and energy conservation equations for a multi-component (electrons, ions, excited species and neutrals) gas mixture, conservation equations for each component of the mixture and state relations. A drift-diffusion approximation for the electron and the ion fluxes is used. A model for the external circuit driving the discharge is also considered and solved along with the discharge model. Many of the key features of a negative corona discharge, namely non-linear current-voltage characteristics, spatially flat cathode current density and glow-like discharge in the high current regime are displayed in the predictions. A transition to the ‘normal’ glow discharge from the corona discharge regime is also observed. The transition is identified from the calculated current-voltage characteristic curve and is characterized by the radial growth of the negative glow and the engulfment of the cathode wire.

  12. Positive direct current corona discharges in single wire-duct electrostatic precipitators

    Science.gov (United States)

    Yehia, Ashraf; Abdel-Fattah, E.; Mizuno, Akira

    2016-05-01

    This paper is aimed to study the characteristics of the positive dc corona discharges in single wire-duct electrostatic precipitators. Therefore, the corona discharges were formed inside dry air fed single wire-duct reactor under positive dc voltage at the normal atmospheric conditions. The corona current-voltage characteristics curves have been measured in parallel with the ozone concentration generated inside the reactor under different discharge conditions. The corona current-voltage characteristics curves have agreed with a semi empirical equation derived from the previous studies. The experimental results of the ozone concentration generated inside the reactor were formulated in the form of an empirical equation included the different parameters that were studied experimentally. The obtained equations are valid to expect both the current-voltage characteristics curves and the corresponding ozone concentration that generates with the positive dc corona discharges inside single wire-duct electrostatic precipitators under any operating conditions in the same range of the present study.

  13. Monte Carlo simulation of corona discharge in SF{sub 6}

    Energy Technology Data Exchange (ETDEWEB)

    Settaouti, A.; Settaouti, L. [Electrotechnic Department, University of Sciences and Technology, P.O. Box 1505, El-M' naouar, Oran (Algeria)

    2010-09-15

    Sulphur hexafluoride (SF{sub 6}) is one of the most widely used gaseous dielectrics for electric power systems and a number of high-voltage applications. There are many industrial applications where the electric corona discharge is used. In most cases the corona discharge is an inherently dynamic process; all parameters vary in time. Monte Carlo simulation of corona discharges in gas offers several advantages to study fundamental processes. Furthermore, it gives a fair qualitative description of the corona discharge itself as a function of space and time. This paper describes the development of negative coronas in SF{sub 6} in a point-plane gap. Detailed structure of avalanches is presented, the total field distribution, propagation of successive avalanches and ion distribution are studied. (author)

  14. Positive direct current corona discharges in single wire-duct electrostatic precipitators

    Energy Technology Data Exchange (ETDEWEB)

    Yehia, Ashraf, E-mail: yehia30161@yahoo.com [Department of Physics, College of Science and Humanitarian Studies at Alkharj, Prince Sattam bin Abdulaziz University, P.O. Box 83, Alkharj 11942 (Saudi Arabia); Department of Physics, Faculty of Science, Assiut University, Assiut 71516, Arab Republic of Egypt (Egypt); Abdel-Fattah, E. [Department of Physics, College of Science and Humanitarian Studies at Alkharj, Prince Sattam bin Abdulaziz University, P.O. Box 83, Alkharj 11942 (Saudi Arabia); Department of Physics, Faculty of Science, Zagazig University, Zagazig 44519, Arab Republic of Egypt (Egypt); Mizuno, Akira [Department of Environmental and Life Sciences, Toyohashi University of Technology, Tempaku-cho, Toyohashi 441-8580 (Japan)

    2016-05-15

    This paper is aimed to study the characteristics of the positive dc corona discharges in single wire-duct electrostatic precipitators. Therefore, the corona discharges were formed inside dry air fed single wire-duct reactor under positive dc voltage at the normal atmospheric conditions. The corona current-voltage characteristics curves have been measured in parallel with the ozone concentration generated inside the reactor under different discharge conditions. The corona current-voltage characteristics curves have agreed with a semi empirical equation derived from the previous studies. The experimental results of the ozone concentration generated inside the reactor were formulated in the form of an empirical equation included the different parameters that were studied experimentally. The obtained equations are valid to expect both the current-voltage characteristics curves and the corresponding ozone concentration that generates with the positive dc corona discharges inside single wire-duct electrostatic precipitators under any operating conditions in the same range of the present study.

  15. Catalytic oxidation of benzene using DBD corona discharges.

    Science.gov (United States)

    Lu, B; Zhang, X; Yu, X; Feng, T; Yao, S

    2006-09-01

    Plasma oxidation of benzene (C(6)H(6)) in oxygen and nitrogen was investigated using a dielectric barrier discharge (DBD) reactor with or without MnO2 or TiO2 at atmospheric pressure and without external heating except plasma heating. An alternative current power supply was used to generate corona discharges for the plasma oxidation. The energy density was controlled under 200 J/L to keep an increase in gas temperature less than 167 K. C(6)H(6) was oxidized to carbon monoxide (CO) and dioxide (CO(2)). Typically, the energy efficiency at an energy density of 92J/L was about 0.052, 0.039, and 0.024 mol/kWh with MnO2, TiO2, and without MnO2 and TiO2, respectively. Benzene oxidation mechanism was mentioned. A comparison on energy efficiency as a function of initial concentration of hydrocarbons, inorganic sulphur compounds, and chloro (fluoro and bromo) carbons was given.

  16. Numerical modelling of ozone production in a wire-cylinder corona discharge and comparison with a wire-plate corona discharge

    Science.gov (United States)

    Wang, Pengxiang; Chen, Junhong

    2009-02-01

    The effect of electrode configuration on ozone production in the direct-current corona discharge of dry and humid air is studied by a numerical model that combines the electron distribution in the corona plasma, plasma chemistry and transport phenomena. Two electrode configurations are considered: wire-cylinder discharge with air flowing along the wire axis and wire-plate discharge with air flowing transverse to the wire. The ozone distributions in both types of discharges are compared. For both electrode configurations, the ozone production rate is higher in the negative corona than in the positive corona and it decreases with an increase in relative humidity. More importantly, the detailed ozone distribution in the neighbourhood of the discharge wire, together with the ozone kinetics, reveals the possible difference in the ozone production from the two discharges. With the same operating conditions and sufficiently short flow residence time, the ozone production rate is nearly the same for both electrode configurations. When the flow residence time is longer than the characteristic time for homogeneous ozone destruction, the net ozone production is higher in the wire-cylinder discharge than in the wire-plate discharge due to relatively less ozone destruction.

  17. ZnO Nanowire-Based Corona Discharge Devices Operated Under Hundreds of Volts

    Science.gov (United States)

    Yang, Wenming; Zhu, Rong; Zong, Xianli

    2016-02-01

    Minimizing the voltage of corona discharges, especially when using nanomaterials, has been of great interest in the past decade or so. In this paper, we report a new corona discharge device by using ZnO nanowires operated in atmospheric air to realize continuous corona discharge excited by hundreds of volts. ZnO nanowires were synthesized on microelectrodes using electric-field-assisted wet chemical method, and a thin tungsten film was deposited on the microchip to enhance discharging performance. The testing results showed that the corona inception voltages were minimized greatly by using nanowires compared to conventional dischargers as a result of the local field enhancement of nanowires. The corona could be continuously generated and self-sustaining. It was proved that the law of corona inception voltage obeyed the conventional Peek's breakdown criterion. An optimal thickness of tungsten film coated over ZnO nanowires was figured out to obtain the lowest corona inception voltage. The ion concentration of the nanowire-based discharger attained 1017/m3 orders of magnitude, which is practicable for most discharging applications.

  18. ZnO Nanowire-Based Corona Discharge Devices Operated Under Hundreds of Volts.

    Science.gov (United States)

    Yang, Wenming; Zhu, Rong; Zong, Xianli

    2016-12-01

    Minimizing the voltage of corona discharges, especially when using nanomaterials, has been of great interest in the past decade or so. In this paper, we report a new corona discharge device by using ZnO nanowires operated in atmospheric air to realize continuous corona discharge excited by hundreds of volts. ZnO nanowires were synthesized on microelectrodes using electric-field-assisted wet chemical method, and a thin tungsten film was deposited on the microchip to enhance discharging performance. The testing results showed that the corona inception voltages were minimized greatly by using nanowires compared to conventional dischargers as a result of the local field enhancement of nanowires. The corona could be continuously generated and self-sustaining. It was proved that the law of corona inception voltage obeyed the conventional Peek's breakdown criterion. An optimal thickness of tungsten film coated over ZnO nanowires was figured out to obtain the lowest corona inception voltage. The ion concentration of the nanowire-based discharger attained 10(17)/m(3) orders of magnitude, which is practicable for most discharging applications.

  19. Effects of temperature and discharge parameters on ozone concentration of negative corona discharge

    Institute of Scientific and Technical Information of China (English)

    WANG Hai-jun; SHENG Lian-xi; XU De-xuan

    2003-01-01

    The relationship of the ozone generation and the heating power, corona wire surface temperature, discharge electrode and netting electrode was studied during the negative corona discharge. The experimental results showed that the ozone concentration reduced with applied voltage decrease. With heating power increase, the ozone concentration of unit current decreased at exponential rate and it almost change no longer over 0.40 W. Under given temperature, the lower the applied voltage was, the smaller the ozone concentration was; while under given applied voltages, only over 11 kV could decrease with the surface temperature increase. The ozone concentration decreased with the lengthening of corona wire, and could reduced to 10 ppb under experimental condition of 14.2 kV; it also decreased with the shortening of wire diameter,and could decrease 67% at best in the given condition. Moreover, it decreased with the increasing size of netting electrode mesh. At the anion current of 1.65 μA, the ozone concentration of 5.0 × 5.0 cm2 is only 41% of that of 3.3 × 3.3 cm2 .

  20. Effect of oxygen on NOx removal in corona discharge field: NOx behavior without a reducing agent

    Energy Technology Data Exchange (ETDEWEB)

    M. Arai; M. Saito; S. Yoshinaga [Gunma University, Gunma (Japan). Department of Mechanical System Engineering

    2004-10-01

    A DeNOx process using a DC corona discharge was investigated experimentally. A mixture system of N{sub 2}/O{sub 2}/NO was used as a test gas. The compositions such as NO, NO{sub 2}, N{sub 2}O and so on were analyzed with Fourier transform infrared spectroscopy and an NOx meter. It was found that the characteristics of NO removal by corona discharge differed remarkably whether or not oxygen exists in the mixture. In regard to the spectrum of light emission from the corona discharge in N{sub 2} atmosphere or N{sub 2}/O{sub 2} mixture, some N{sub 2} bands were detected. N{sub 2} dissociation into atomic N and N{sub 2} radical in the corona discharge field was conjectured. Furthermore, ozone was yielded by the corona discharge in the case of the N{sub 2}/O{sub 2} mixture. Ozone gas from an ozonizer was added into the N{sub 2}/O{sub 2} mixture without corona discharge to investigate the effect of O{sub 3} on the characteristics of NOx removal by corona discharge. In the case of the N{sub 2}/NO mixture, the process of NO reduction was mainly controlled by N{sub 2} radicals excited by the corona discharge. On the other hand, in the case of the N{sub 2}/O{sub 2}/NO mixture, NO was oxidized by ozone generated from the corona discharge and converted to NO{sub 2} and N{sub 2}O{sub 5}.

  1. The role of photoionization in negative corona discharge: The influences of temperature, humidity, and air pressure on a corona

    Science.gov (United States)

    Sun, H. Y.; Lu, B. X.; Wang, M.; Guo, Q. F.; Feng, Q. K.

    2017-10-01

    The swarm parameters of the negative corona discharge are improved to calculate the discharge model under different environmental conditions. The effects of temperature, humidity, and air pressure are studied using a conventional needle-to-plane configuration in air. The electron density, electric field, electron generation rate, and photoelectron generation rate are discussed in this paper. The role of photoionization under these conditions is also studied by numerical simulation. The photoelectrons generated in weak ionization region are proved to be dominant.

  2. Food waste management using an electrostatic separator with corona discharge

    Energy Technology Data Exchange (ETDEWEB)

    Lai, Koonchun; Teh, Pehchiong [Faculty of Engineering and Green Technology, Universiti Tunku Abdul Rahman (Malaysia); Lim, Sooking [Faculty of Engineering and Science, Universiti Tunku Abdul Rahman (Malaysia)

    2015-05-15

    In Malaysia, municipal solid waste contains a high portion of organic matters, typically contributed by food waste. It is estimated that about 45% of the municipal waste are food waste, followed by the non-food waste such as plastics, metals, glass and others. Food waste, while being properly sorted and contamination free from non-food waste, can be reused (e.g. fertiliser) instead of being landfilled. Therefore, recycling of food waste is crucial not only from the view point of waste management, but also with respect to the reduction of resource losses and greenhouse gases emission. A new waste separation process involved food particles, non-food particles and electrostatic discharge was investigated in this study. The empirical results reveal that the corona electrostatic separation is an environmental-friendly way in recovering foods from municipal waste. The efficiency of the separator, under same operating conditions, varies with the particle size of the food and non-food particles. The highest efficiency of 82% is recorded for the particle sizes between 1.5 and 3.0 mm.

  3. Food waste management using an electrostatic separator with corona discharge

    Science.gov (United States)

    Lai, Koonchun; Lim, Sooking; Teh, Pehchiong

    2015-05-01

    In Malaysia, municipal solid waste contains a high portion of organic matters, typically contributed by food waste. It is estimated that about 45% of the municipal waste are food waste, followed by the non-food waste such as plastics, metals, glass and others. Food waste, while being properly sorted and contamination free from non-food waste, can be reused (e.g. fertiliser) instead of being landfilled. Therefore, recycling of food waste is crucial not only from the view point of waste management, but also with respect to the reduction of resource losses and greenhouse gases emission. A new waste separation process involved food particles, non-food particles and electrostatic discharge was investigated in this study. The empirical results reveal that the corona electrostatic separation is an environmental-friendly way in recovering foods from municipal waste. The efficiency of the separator, under same operating conditions, varies with the particle size of the food and non-food particles. The highest efficiency of 82% is recorded for the particle sizes between 1.5 and 3.0 mm.

  4. Towards metals analysis using corona discharge ionization ion mobility spectrometry.

    Science.gov (United States)

    Jafari, Mohammad T; Saraji, Mohammad; Sherafatmand, Hossein

    2016-02-25

    For the first time, the capability of corona discharge ionization ion mobility spectrometry (CD-IMS) in the determination of metal complex was evaluated. The extreme simplicity of dispersive liquid-liquid microextraction (DLLME) coupled to the high sensitivity of CD-IMS measurement could make this combination really useful for simple, rapid, and sensitive determination of metals in different samples. In this regard, mercury, as a model metal, was complexed with diethyldithiocarbamate (DEDTC), and then extracted into the carbon tetrachloride using DLLME. Some parameters affecting the extraction efficiency, including the type and volume of the extraction solvent, the type and volume of the disperser solvent, the concentration of the chelating agent, salt addition and, pH were exhaustively investigated. Under the optimized condition, the enrichment factor was obtained to be 142. The linear range of 0.035-10.0 μg mL(-1) with r(2) = 0.997 and the detection limit of 0.010 μg mL(-1) were obtained. The relative standard deviation values were calculated to be lower than 4% and 8% for intra-day and inter-day, respectively. Finally, the developed method was successfully applied for the extraction and determination of mercury in various real samples. The satisfactory results revealed the capability of the proposed method in trace analysis without tedious derivatization or hydride generation.

  5. Sterilisation of Hydroponic Culture Solution Contaminated by Fungi using an Atmospheric Pressure Corona Discharge

    Science.gov (United States)

    Mizukami, Kohji; Satoh, Kohki; Kanayama, Hiroshi; Itoh, Hidenori; Tagashira, Hiroaki; Shimozuma, Mitsuo; Okamoto, Hiroyuki; Takasaki, Satoko; Kinoshita, Muneshige

    The hydroponic culture solution contaminated by fungi is sterilised by a DC corona discharge, and the sterilisation characteristics are investigated in this work. A DC streamer corona discharge is generated at atmospheric pressure in air between needle clusters and a water bath containing contaminated solution by fungus such as Fusarium oxysporum f. sp. spinaciae or Fusarium sp.. It is found that the fungi are killed by the exposure of the corona discharge, and that the death rates of the fungi chiefly depend on the concentration of the hydroponic culture solutions. It is also found that the number densities of the fungi decrease exponentially with the energy expenditure of the corona discharge, and that damping coefficients of the fungi densities depend on the concentration of the hydroponic culture solutions. This suggests that the fungi are chiefly inactivated by electroporation.

  6. Optical properties and chemical behavior of Laser-dye Coumarin-500 and the influence of atmospheric corona discharges.

    Science.gov (United States)

    Keskin, S Sinan; Aslan, Necdet; Bayrakçeken, Fuat

    2009-03-01

    Structure elucidation of Coumarin-500 Laser-dye in cyclohexane at room temperature has been studied by UV-Vis, Raman, and FTIR spectroscopic techniques. Optical properties and chemical behavior under the influence of atmospheric positive electric pulsed corona discharges were also examined. The effects of UV-Vis irradiation changed some optical parameters, such as decrease in optical density on the absorption spectrum and formation of photoproducts, due to the chromaticity removal. No significant optical changes were observed in the light absorption upon UV-irradiation but large changes in absorption spectrum were observed after positive electric corona discharge treatments, FTIR and Raman spectra in non-polar solvent are recorded and interpreted.

  7. Plasma Discharge Process in a Pulsed Diaphragm Discharge System

    Science.gov (United States)

    Duan, Jianjin; Hu, Jue; Zhang, Chao; Wen, Yuanbin; Meng, Yuedong; Zhang, Chengxu

    2014-12-01

    As one of the most important steps in wastewater treatment, limited study on plasma discharge process is a key challenge in the development of plasma applications. In this study, we focus on the plasma discharge process of a pulsed diaphragm discharge system. According to the analysis, the pulsed diaphragm discharge proceeds in seven stages: (1) Joule heating and heat exchange stage; (2) nucleated site formation; (3) plasma generation (initiation of the breakdown stage); (4) avalanche growth and plasma expansion; (5) plasma contraction; (6) termination of the plasma discharge; and (7) heat exchange stage. From this analysis, a critical voltage criterion for breakdown is obtained. We anticipate this finding will provide guidance for a better application of plasma discharges, especially diaphragm plasma discharges.

  8. Effects of the Liquid Conductivity on Pulsed High-voltage Discharge Modes in Water

    Institute of Scientific and Technical Information of China (English)

    Bin YANG; Le Cheng LEI; Ming Hua ZHOU

    2004-01-01

    Spark, stream and corona pulsed high-voltage discharges in water induced by the various initial conductivities have been examined in this paper. The discharge modes changed from spark to corona discharge with the liquid conductivity increasing. The apparent production of OH radical and quantum yield generated by spark discharge in distilled water were 11.57 μmol/L and 0.0978photon/s, respectively. A preliminary study on acid fuchsine (AF) treatment indicated that higher AF removal efficiency has been achieved by spark discharge. The process of degradation showed that the oxidative effects through OH radical oxidation did not play an important role and did increase with the discharge mode changing to spark discharge.

  9. Multiscale simulation of DC corona discharge and ozone generation from nanostructures

    Science.gov (United States)

    Wang, Pengxiang

    Atmospheric direct current (dc) corona discharge from micro-sized objects has been widely used as an ion source in many devices, such as photocopiers, laser printers, and electronic air cleaners. Shrinking the size of the discharge electrode to the nanometer range (e.g., through the use of carbon nanotubes or CNTs) is expected to lead to a significant reduction in power consumption and detrimental ozone production in these devices. The objectives of this study are to unveil the fundamental physics of the nanoscale corona discharge and to evaluate its performance and ozone production through numerical models. The extremely small size of CNTs presents considerable complexity and challenges in modeling CNT corona discharges. A hybrid multiscale model, which combines a kinetic particle-in-cell plus Monte Carlo collision (PIC-MCC) model and a continuum model, is developed to simulate the corona discharge from nanostructures. The multiscale model is developed in several steps. First, a pure PIC-MCC model is developed and PIC-MCC simulations of corona plasma from micro-sized electrode with same boundary conditions as prior model are performed to validate the PIC-MCC scheme. The agreement between the PIC-MCC model and the prior continuum model indicates the validity of the PIC-MCC scheme. The validated PIC-MCC scheme is then coupled with a continuum model to simulate the corona discharge from a micro-sized electrode. Unlike the prior continuum model which only predicts the corona plasma region, the hybrid model successfully predicts the self-consistent discharge process in the entire corona discharge gap that includes both corona plasma region and unipolar ion region. The voltage-current density curves obtained by the hybrid model agree well with analytical prediction and experimental results. The hybrid modeling approach, which combines the accuracy of a kinetic model and the efficiency of a continuum model, is thus validated for modeling dc corona discharges. For

  10. Experimental Investigation of the Corona Discharge in Electrical Transmission due to AC/DC Electric Fields

    Directory of Open Access Journals (Sweden)

    Fuangpian Phanupong

    2016-01-01

    Full Text Available Nowadays, using of High Voltage Direct Current (HVDC transmission to maximize the transmission efficiency, bulk power transmission, connection of renewable power source from wind farm to the grid is of prime concern for the utility. However, due to the high electric field stress from Direct Current (DC line, the corona discharge can easily be occurred at the conductor surface leading to transmission loss. Therefore, the polarity effect of DC lines on corona inception and breakdown voltage should be investigated. In this work, the effect of DC polarity and Alternating Current (AC field stress on corona inception voltage and corona discharge is investigated on various test objects, such as High Voltage (HV needle, needle at ground plane, internal defect, surface discharge, underground cable without cable termination, cable termination with simulated defect and bare overhead conductor. The corona discharge is measured by partial discharge measurement device with high-frequency current transformer. Finally, the relationship between supply voltage and discharge intensity on each DC polarity and AC field stress can be successfully determined.

  11. Pulsed electrical discharge in gas bubbles in water

    Science.gov (United States)

    Gershman, Sophia

    A phenomenological picture of pulsed electrical discharge in gas bubbles in water is produced by combining electrical, spectroscopic, and imaging methods. The discharge is generated by applying one microsecond long 5 to 20 kilovolt pulses between the needle and disk electrodes submerged in water. A gas bubble is generated at the tip of the needle electrode. The study includes detailed experimental investigation of the discharge in argon bubbles and a brief look at the discharge in oxygen bubbles. Imaging, electrical characteristics, and time-resolved optical emission data point to a fast streamer propagation mechanism and formation of a plasma channel in the bubble. Spectroscopic methods based on line intensity ratios and Boltzmann plots of line intensities of argon, atomic hydrogen, and argon ions and the examination of molecular emission bands from molecular nitrogen and hydroxyl radicals provide evidence of both fast beam-like electrons and slow thermalized ones with temperatures of 0.6 -- 0.8 electron-volts. The collisional nature of plasma at atmospheric pressure affects the decay rates of optical emission. Spectroscopic study of rotational-vibrational bands of hydroxyl radical and molecular nitrogen gives vibrational and rotational excitation temperatures of the discharge of about 0.9 and 0.1 electron-volt, respectively. Imaging and electrical evidence show that discharge charge is deposited on the bubble wall and water serves as a dielectric barrier for the field strength and time scales of this experiment. Comparing the electrical and imaging information for consecutive pulses applied at a frequency of 1 Hz indicates that each discharge proceeds as an entirely new process with no memory of the previous discharge aside from long-lived chemical species, such as ozone and oxygen. Intermediate values for the discharge gap and pulse duration, low repetition rate, and unidirectional character of the applied voltage pulses make the discharge process here unique

  12. Heating dominated inception of pulsed discharges

    Science.gov (United States)

    Agnihotri, Ashutosh; Hundsdorfer, Willem; Ebert, Ute

    2016-09-01

    We simulate the inception of pulsed discharges with heating as the driving agent that leads to spark formation. To understand the phenomenon, we developed a 2D-cylindrically symmetric model that couples the electric discharge dynamics with the background gas dynamics. To capture the ion dynamics well, we reduced the classical drift-diffusion-reaction model of electric discharges to the timescale of ion motion. Additionally, we include secondary emission of electrons from the cathode. We employed the model to study electrical breakdown in air at STP conditions between planar electrodes under the application of pulsed voltages. Our model captures space-charge effects, thermal shocks and induced pressure waves. We observe a cycle of discharge pulses heating the gas and the thermal expansion helping the discharge. This cycle might either lead to spark formation or to discharge decay.

  13. Pulsed Corona Plasma Technology for Treating VOC Emissions from Pulp Mills

    Energy Technology Data Exchange (ETDEWEB)

    Fridman, Alexander A.; Gutsol, Alexander; Kennedy, Lawrence A.; Saveliev, Alexei V.; Korobtsev, Sergey V.; Shiryaevsky, Valery L.; Medvedev, Dmitry

    2004-07-28

    Under the DOE Office of Industrial Technologies Forest Products program various plasma technologies were evaluated under project FWP 49885 ''Experimental Assessment of Low-Temperature Plasma Technologies for Treating Volatile Organic Compound Emissions from Pulp Mills and Wood Products Plants''. The heterogeneous pulsed corona discharge was chosen as the best non-equilibrium plasma technology for control of the vent emissions from HVLC Brownstock Washers. The technology for removal of Volatile Organic Compounds (VOCs) from gas emissions with conditions typical of the exhausts of the paper industry by means of pulsed corona plasma techniques presented in this work. For the compounds of interest in this study (methanol, acetone, dimethyl sulfide and ? -pinene), high removal efficiencies were obtained with power levels competitive with the present technologies for the VOCs removal. Laboratory experiments were made using installation with the average power up to 20 W. Pilot plant prepared for on-site test has average plasma power up to 6.4 kW. The model of the Pilot Plant operation is presented.

  14. A DC corona discharge on a flat plate to induce air movement

    OpenAIRE

    Magnier, Pierre; Hong, Dunpin; Leroy-Chesneau, Annie; Pouvesle, Jean-Michel; Hureau, Jacques

    2007-01-01

    International audience; This paper describes a DC surface corona discharge designed to modify the airflow around a flat plate. The electrode configuration consisted of two thin copper layers placed on each side of the plate's attack edge. Discharge optical measurements with a photomultiplier tube indicated that the light emitted by the plasma is pulsating, at a frequency that increases with applied voltage. Moreover, with voltage higher than a threshold value, the electric discharge changes r...

  15. Use of volatile additives to increase the antimicrobial efficacy of a corona discharge

    OpenAIRE

    Gaunt, L.F.; Hughes, J.F.

    2004-01-01

    The antimicrobial effects of charged reactive ion species produced by cold plasma discharges are well recognized. Total sterilization can be achieved on media in close proximity to the plasma source (1). The aim of this research was to investigate whether the antimicrobial efficacy of a corona discharge could be improved by the use of antimicrobial volatile additives in the gas mixture of the discharge. Volatile compounds known to have good antimicrobial effects, such as ethyl alcohol, cinnam...

  16. Surface-initiated graft polymerization on multiwalled carbon nanotubes pretreated by corona discharge at atmospheric pressure.

    Science.gov (United States)

    Xu, Lihua; Fang, Zhengping; Song, Ping'an; Peng, Mao

    2010-03-01

    Surface-initiated graft polymerization on multi-walled carbon nanotubes pretreated with a corona discharge at atmospheric pressure was explored. The mechanism of the corona-discharge-induced graft polymerization is discussed. The results indicate that MWCNTs were encapsulated by poly(glycidyl methacrylate) (PGMA), demonstrating the formation of PGMA-grafted MWCNTs (PGMA-g-MWCNTs), with a grafting ratio of about 22 wt%. The solubility of PGMA-g-MWCNTs in ethanol was dramatically improved compared to pristine MWCNTs, which could contribute to fabricating high-performance polymer/MWCNTs nanocomposites in the future. Compared with most plasma processes, which operate at low pressures, corona discharge has the merit of working at atmospheric pressure.

  17. Combined corona discharge and UV photoionization source for ion mobility spectrometry.

    Science.gov (United States)

    Bahrami, Hamed; Tabrizchi, Mahmoud

    2012-08-15

    An ion mobility spectrometer is described which is equipped with two non-radioactive ion sources, namely an atmospheric pressure photoionization and a corona discharge ionization source. The two sources cannot only run individually but are additionally capable of operating simultaneously. For photoionization, a UV lamp was mounted parallel to the axis of the ion mobility cell. The corona discharge electrode was mounted perpendicular to the UV radiation. The total ion current from the photoionization source was verified as a function of lamp current, sample flow rate, and drift field. Simultaneous operation of the two ionization sources was investigated by recording ion mobility spectra of selected samples. The design allows one to observe peaks from either the corona discharge or photoionization individually or simultaneously. This makes it possible to accurately compare peaks in the ion mobility spectra from each individual source. Finally, the instrument's capability for discriminating two peaks appearing in approximately identical drift times using each individual ionization source is demonstrated.

  18. Positive direct current corona discharges in single wire-duct electrostatic precipitators

    Directory of Open Access Journals (Sweden)

    Ashraf Yehia

    2016-05-01

    Full Text Available This paper is aimed to study the characteristics of the positive dc corona discharges in single wire-duct electrostatic precipitators. Therefore, the corona discharges were formed inside dry air fed single wire-duct reactor under positive dc voltage at the normal atmospheric conditions. The corona current-voltage characteristics curves have been measured in parallel with the ozone concentration generated inside the reactor under different discharge conditions. The corona current-voltage characteristics curves have agreed with a semi empirical equation derived from the previous studies. The experimental results of the ozone concentration generated inside the reactor were formulated in the form of an empirical equation included the different parameters that were studied experimentally. The obtained equations are valid to expect both the current-voltage characteristics curves and the corresponding ozone concentration that generates with the positive dc corona discharges inside single wire-duct electrostatic precipitators under any operating conditions in the same range of the present study.

  19. [Morphology determination of multi-needle-to-plate positive corona discharge].

    Science.gov (United States)

    Su, Peng-hao; Zhu, Yi-min; Chen, Hai-feng

    2008-09-01

    Using the method of OES (optical emission spectrum) for measuring N2 emission spectrum, the distribution of the energetic electrons in multi-needle-to-plate positive corona discharge at atmospheric pressure was investigated, and compared with that in negative corona discharge. According to the distribution of N2 second positive band's intensity I(SPB), the outline of the ionization region in glow discharge and the streamer channel were drawn rather accurately. The relationship between I(SPB) and the discharge current I in glow discharge can be obtained through the volume integral of the I(SPB). In glow discharge, both the ionization region scale and I(SPB) are smaller than in negative corona discharge, the electron avalanche develops farther along the radius direction of needle than along axis direction, and only the arrange along axis direction is enhanced slightly with the rise of the applied voltage U. The integral of I(SPB) is second order linear to I. In streamer discharge, the discharge channels develop from needlepoint to the plate, while the shape of the region in which I(SPB) is higher looks like a bullet. The density of energetic electron in the channel farther away from the needlepoint is relatively uniform along the axis direction, but first increases then decreases along the radius direction.

  20. Study on law of negative corona discharge in microparticle-air two-phase flow media

    Directory of Open Access Journals (Sweden)

    Bo He

    2016-03-01

    Full Text Available To study the basic law of negative corona discharge in solid particle-air two-phase flow, corona discharge experiments in a needle-plate electrode system at different voltage levels and different wind speed were carried out in the wind tunnel. In this paper, the change law of average current and current waveform were analyzed, and the observed phenomena were systematically explained from the perspectives of airflow, particle charging, and particle motion with the help of PIV (particle image velocity measurements and ultraviolet observations.

  1. Estimation of winding insulation resistance to the corona discharges

    Science.gov (United States)

    Leonov, A.; Red'ko, V.; Soldatenko, E.

    2014-10-01

    This article presents test results of enameled winding wires, characterizing an insulation electrical and mechanical strength. Standard and original test methods were used. Note that existing standard test methods do not estimate enamel insulation resistance to the electrical loads under winding operation of variable-speed drive. We show that estimation of wire corona resistance can be done by high frequency electrical impulse testing. Wire insulation plays the main role of reliability of insulation system.

  2. Nanoscale discharge electrode for minimizing ozone emission from indoor corona devices.

    Science.gov (United States)

    Bo, Zheng; Yu, Kehan; Lu, Ganhua; Mao, Shun; Chen, Junhong; Fan, Fa-Gung

    2010-08-15

    Ground-level ozone emitted from indoor corona devices poses serious health risks to the human respiratory system and the lung function. Federal regulations call for effective techniques to minimize the indoor ozone production. In this work, stable atmospheric corona discharges from nanomaterials are demonstrated using horizontally suspended carbon nanotubes (CNTs) as the discharge electrode. Compared with the conventional discharges employing micro- or macroscale electrodes, the corona discharge from CNTs could initiate and operate at a much lower voltage due to the small electrode diameter, and is thus energy-efficient. Most importantly, the reported discharge is environmentally friendly since no ozone (below the detection limit of 0.5 ppb) was detected for area current densities up to 0.744 A/m(2) due to the significantly reduced number of electrons and plasma volume generated by CNT discharges. The resulting discharge current density depends on the CNT loading. Contrary to the conventional wisdom, negative CNT discharges should be used to enhance the current density owing to the efficient field emission of electrons from the CNT surface.

  3. Change of the electron attachment coefficient caused by corona discharge in oxygen. Sanso gas chu, corona hoden ni yoru denshi fuchaku keisu no henka

    Energy Technology Data Exchange (ETDEWEB)

    Kajita, Shogo; Kondo, Yoshitaka; Ushiroda, Sumio (Toyota College of Tech., Aichi (Japan))

    1989-12-01

    The relationship between the electron attachment coefficient of ozone which is one of gases genearated during discharge and the ozone concentration was determined by discharging negative corona discharge in pure oxygen to research and develop a small and highly efficient ozonizer. These measured results are useful as the basic data necessary for simulation of a ozonizer using oxygen as the raw material. The experiment was carried out by releasing photo-electrons generated by pulse glow discharging with a Xe lamp in oxygen sealed into a drifttube, by generating negative ions due to attaching electrons to gaseous molecules and by measuring the induced current accompanied by the transfer. As the results, if ozone of hundreds of ppm is contained in oxygen, followings were confirmed: electron attachment coefficient increased for E/N of about 10Td or less, where E is electric charge and N is molecular density of gas; electron attachment coefficient increased by the dissociative attachment of ozone for E/N of about 10Td or less; and further, the cross section of dissociative attachment for ozone could be estimated by solving the Boltzmann equation. 12 refs., 11 figs., 1 tab.

  4. Space Charge Transient Kinetic Characteristics in DC Air Corona Discharge at Atmospheric Pressure

    Science.gov (United States)

    Liu, Xinghua; Xian, Richang; Sun, Xuefeng; Wang, Tao; Lv, Xuebin; Chen, Suhong; Yang, Fan

    2014-08-01

    Investigating the corona mechanism plays a key role in enhancing the performance of electrical insulation systems. Numerical simulation offers a better understanding of the physical characteristics of air corona discharges. Using a two-dimensional axisymmetrical kinetics model, into which the photoionization effect is incorporated, the DC air corona discharge at atmosphere pressure is studied. The plasma model is based on a self-consistent, multi-component, and continuum description of the air discharge, which is comprised of 12 species and 22 reactions. The discharge voltage-current characteristic predicted by the model is found to be in quite good agreement with experimental measurements. The behavior of the electronic avalanche progress is also described. O2+ and N2+ are the dominant positive ions, and the values of O- and O2- densities are much smaller than that of the electron. The electron and positive ion have a low-density thin layer near the anode, which is a result of the surface reaction and absorption effect of the electrode. As time progresses, the electric field increases and extends along the cathode surface, whereas the cathode fall shrinks after the corona discharge hits the cathode; thus, in the cathode sheath, the electron temperature increases and the position of its peak approaches to the cathode. The present computational model contributes to the understanding of this physical mechanism, and suggests ways to improve the electrical insulation system.

  5. A semi-analytical study of positive corona discharge in wire-plane electrode configuration

    Science.gov (United States)

    Yanallah, K.; Pontiga, F.; Chen, J. H.

    2013-08-01

    Wire-to-plane positive corona discharge in air has been studied using an analytical model of two species (electrons and positive ions). The spatial distributions of electric field and charged species are obtained by integrating Gauss's law and the continuity equations of species along the Laplacian field lines. The experimental values of corona current intensity and applied voltage, together with Warburg's law, have been used to formulate the boundary condition for the electron density on the corona wire. To test the accuracy of the model, the approximate electric field distribution has been compared with the exact numerical solution obtained from a finite element analysis. A parametrical study of wire-to-plane corona discharge has then been undertaken using the approximate semi-analytical solutions. Thus, the spatial distributions of electric field and charged particles have been computed for different values of the gas pressure, wire radius and electrode separation. Also, the two dimensional distribution of ozone density has been obtained using a simplified plasma chemistry model. The approximate semi-analytical solutions can be evaluated in a negligible computational time, yet provide precise estimates of corona discharge variables.

  6. [Research on electron density in DC needle-plate corona discharge at atmospheric pressure].

    Science.gov (United States)

    Liu, Zhi-Qiang; Guo, Wei; Liu, Tao-Tao; Wu, Wen-Shuo; Liu, Shu-Min

    2013-11-01

    Using needle-plate discharge device, corona discharge experiment was done in the atmosphere. Through photo of spot size of light-emitting area, the relationship between the voltage and thickness of corona layer was discussed. When the distance between tip and plate is fixed, the thickness of corona layer increases with the increase in voltage; when the voltage is fixed, the thickness of corona layer decreases with the increase in the distance between tip and plate. As spectral intensity of N2 (C3pi(u)) (337.1 nm)reflects high energy electron density, it was measured with emission spectrometry. The results show that high energy electron density is the biggest near the needle tip and the relationship between high energy electron density and voltage is basically linear increasing. Fixing voltage, high energy electron density decreases with the increase in the distance between tip and plate. When the voltage and the distance between tip and plate are fixed, the high energy electron density increases with the decrease in the curvature radius of needle tip. These results are of great importance for the study of plasma parameters of corona discharge.

  7. Simulation of Thermal and Chemical Relaxation in a Post-Discharge Air Corona Reactor

    CERN Document Server

    Meziane, M; Ducasse, O; Yousfi, M

    2016-01-01

    In a DC point-to-plane corona discharge reactor, the mono filamentary streamers cross the inter electrode gap with a natural repetition frequency of some tens of kHz. The discharge phase (including the primary and the secondary streamers development) lasts only some hundred of nanoseconds while the post-discharge phases occurring between two successive discharge phases last some tens of microseconds. From the point of view of chemical activation, the discharge phases create radical and excited species located inside the very thin discharge filaments while during the post-discharge phases these radical and excited species induce a chemical kinetics that diffuse in a part of the reactor volume. From the point of view of hydrodynamics activation, the discharge phases induce thermal shock waves and the storage of vibrational energy which relaxes into thermal form only during the post-discharge phase. Furthermore, the glow corona discharges that persist during the post-discharge phases induce the so called electri...

  8. Removal of NO and SO2 in Corona Discharge Plasma Reactor with Water Film

    Institute of Scientific and Technical Information of China (English)

    贺元吉; 董丽敏; 杨嘉祥

    2004-01-01

    In this paper, a novel type of a corona discharge plasma reactor was designed, which consists of needle-plate-combined electrodes, in which a series of needle electrodes are placed in a glass container filled with flue gas, and a plate electrode is immersed in the water. Based on this model, the removal of NO and SO2 was tested experimentally. In addition, the effect of streamer polarity on the reduction of SO2 and NO was investigated in detail. The experimental results show that the corona wind formed between the high-voltage needle electrode and the water by corona discharge enhances the cleaning efficiency of the flue gas because of the presence of water,and the cleaning efficiency will increase with the increase of applied dc voltage within a definite range. The removal efficiency of SO2 up to 98%, and about 85% of NOx removal under suitable conditions is obtained in our experiments.

  9. Comparison of pulsed corona plasma and pulsed electric fields for the decontamination of water containing Legionella pneumophila as model organism.

    Science.gov (United States)

    Banaschik, Robert; Burchhardt, Gerhard; Zocher, Katja; Hammerschmidt, Sven; Kolb, Juergen F; Weltmann, Klaus-Dieter

    2016-12-01

    Pulsed corona plasma and pulsed electric fields were assessed for their capacity to kill Legionella pneumophila in water. Electrical parameters such as in particular dissipated energy were equal for both treatments. This was accomplished by changing the polarity of the applied high voltage pulses in a coaxial electrode geometry resulting in the generation of corona plasma or an electric field. For corona plasma, generated by high voltage pulses with peak voltages of +80kV, Legionella were completely killed, corresponding to a log-reduction of 5.4 (CFU/ml) after a treatment time of 12.5min. For the application of pulsed electric fields from peak voltages of -80kV a survival of log 2.54 (CFU/ml) was still detectable after this treatment time. Scanning electron microscopy images of L. pneumophila showed rupture of cells after plasma treatment. In contrast, the morphology of bacteria seems to be intact after application of pulsed electric fields. The more efficient killing for the same energy input observed for pulsed corona plasma is likely due to induced chemical processes and the generation of reactive species as indicated by the evolution of hydrogen peroxide. This suggests that the higher efficacy and efficiency of pulsed corona plasma is primarily associated with the combined effect of the applied electric fields and the promoted reaction chemistry.

  10. Ozone generation by negative corona discharge: the effect of Joule heating

    Science.gov (United States)

    Yanallah, K.; Pontiga, F.; Fernández-Rueda, A.; Castellanos, A.; Belasri, A.

    2008-10-01

    Ozone generation in pure oxygen using a wire-to-cylinder corona discharge reactor is experimentally and numerically investigated. Ozone concentration is determined by means of direct UV spectroscopy and the effects of Joule heating and ozone decomposition on the electrodes are analysed for different discharge gaps. The numerical model combines the physical processes in the corona discharge with the chemistry of ozone formation and destruction. The chemical kinetics model and the electrical model are coupled through Poisson's equation, and the current-voltage (CV) characteristic measured in experiments is used as input data to the numerical simulation. The numerical model is able to predict the radial distributions of electrons, ions, atoms and molecules for each applied voltage of the CV characteristic. In particular, the evolution of ozone density inside the discharge cell has been investigated as a function of current intensity and applied voltage.

  11. Ozone generation by negative corona discharge: the effect of Joule heating

    Energy Technology Data Exchange (ETDEWEB)

    Yanallah, K; Castellanos, A [Departamento de Electronica y Electromagnetismo, Universidad de Sevilla (Spain); Pontiga, F; Fernandez-Rueda, A [Departamento de Fisica Aplicada II, Universidad de Sevilla (Spain); Belasri, A [Laboratoire de Physique des Plasmas, des Materiaux Conducteur et Leurs Applications, Universite d' Oran (Algeria)

    2008-10-07

    Ozone generation in pure oxygen using a wire-to-cylinder corona discharge reactor is experimentally and numerically investigated. Ozone concentration is determined by means of direct UV spectroscopy and the effects of Joule heating and ozone decomposition on the electrodes are analysed for different discharge gaps. The numerical model combines the physical processes in the corona discharge with the chemistry of ozone formation and destruction. The chemical kinetics model and the electrical model are coupled through Poisson's equation, and the current-voltage (CV) characteristic measured in experiments is used as input data to the numerical simulation. The numerical model is able to predict the radial distributions of electrons, ions, atoms and molecules for each applied voltage of the CV characteristic. In particular, the evolution of ozone density inside the discharge cell has been investigated as a function of current intensity and applied voltage.

  12. An efficient model to simulate stable glow corona discharges and their transition into streamers

    Science.gov (United States)

    Liu, Lipeng; Becerra, Marley

    2017-03-01

    A computationally efficient model to evaluate stable glow corona discharges and their transition into streamers is proposed. The simplified physical model referred to as the SPM is based on the classic hydrodynamic model of charge particles and a quasi-steady state approximation for electrons. The solution follows a two-step segregated procedure, which solves sequentially the stationary continuity equation for electrons and then time-dependent continuity equations for ions. The validity of using the SPM to simulate glow corona discharges and their transition into streamers is demonstrated by performing comparisons with a fully coupled physical model (FPM) and with experimental data available in the literature for air under atmospheric conditions. It is shown that the SPM can obtain estimates similar to those calculated with the FPM and those measured in experiments but using significantly less computation time. Since the proposed model simulates efficiently the ionization layer without prior knowledge of the surface electric field or the discharge current, it is a computationally efficient alternative to calculations of glow corona discharges based on Kaptzov’s approximation (KAM). The model can also be employed to efficiently calculate the conditions for the transition of glow corona into streamers, overcoming the limitations of KAM to provide such estimates.

  13. Corona discharges with water electrospray for Escherichia coli biofilm eradication on a surface.

    Science.gov (United States)

    Kovalova, Zuzana; Leroy, Magali; Kirkpatrick, Michael J; Odic, Emmanuel; Machala, Zdenko

    2016-12-01

    Low-temperature plasma (cold), a new method for the decontamination of surfaces, can be an advantageous alternative to the traditional chemical methods, autoclave or dry heat. Positive and negative corona discharges in air were tested for the eradication of 48-h Escherichia coli biofilms grown on glass slides. The biofilms were treated by cold corona discharge plasma for various exposure times. Water electrospray from the high voltage electrode was applied in some experiments. Thermostatic cultivation of the biofilm, and confocal laser scanning microscopy (CLSM) of the biofilm stained with fluorescent dyes were used for biocidal efficiency quantification. Up to 5 log10 reduction of bacterial concentration in the biofilm was measured by thermostatic cultivation after exposure to both corona discharges for 15min. This decontamination efficiency was significantly enhanced by simultaneous water electrospray through the plasma. CLSM showed that the live/dead ratio after treatment remained almost constant inside the biofilm; only cells on the top layers of the biofilm were affected. DAPI fluorescence showed that biofilm thickness was reduced by about 1/3 upon exposure to the corona discharges with electrospray for 15min. The biofilm biomass loss by about 2/3 was confirmed by crystal violet assay.

  14. On-Line Mass Spectrometry Detection of Heavy Metals by Electrothermal Vaporization-Assisted Pulsed Corona Discharge Ionization Source under Ambient Conditions%基于电热蒸发辅助脉冲电晕放电大气压离子化源的重金属污染在线质谱检测技术

    Institute of Scientific and Technical Information of China (English)

    周建光; 林静; 张涛; 张体强; 牟颖

    2011-01-01

    A home-made electrothermal vaporization-assisted pulsed corona discharge atmospheric pressure ionization source was developed for coupling with a time-of-flight mass spectrometer for on-line detection of heavy metals in water samples. Experimental results show that vanadium, chromium, manganese, arsenic,including arsenic, chromium, which are great harmful to the environment, could be detected. The source has a simple structure, convenient operation, low energy consumption, and is easy to use, with a high sensitivity.The limit of detection can get to 10-13-10-12 g, and the method can be used online.%研制电热蒸发辅助脉冲电晕放电大气压离子化源,将其与飞行时间质谱耦合联用,建立了重金属污染的在线检测方法.实验结果表明,该方法对V,Cr,Mn,As等主要重金属污染物检测性能较好,灵敏度高,检出限一般可达10-13~10-12 g,具有结构简单、操作方便、能耗低等特点,实现了在线监测.

  15. Multiphysics simulation of corona discharge induced ionic wind

    CERN Document Server

    Cagnoni, Davide; Christen, Thomas; de Falco, Carlo; Parolini, Nicola; Stevanović, Ivica

    2013-01-01

    Ionic wind devices or electrostatic fluid accelerators are becoming of increasing interest as tools for thermal management, in particular for semiconductor devices. In this work, we present a numerical model for predicting the performance of such devices, whose main benefit is the ability to accurately predict the amount of charge injected at the corona electrode. Our multiphysics numerical model consists of a highly nonlinear strongly coupled set of PDEs including the Navier-Stokes equations for fluid flow, Poisson's equation for electrostatic potential, charge continuity and heat transfer equations. To solve this system we employ a staggered solution algorithm that generalizes Gummel's algorithm for charge transport in semiconductors. Predictions of our simulations are validated by comparison with experimental measurements and are shown to closely match. Finally, our simulation tool is used to estimate the effectiveness of the design of an electrohydrodynamic cooling apparatus for power electronics applicat...

  16. Multiphysics simulation of corona discharge induced ionic wind

    Energy Technology Data Exchange (ETDEWEB)

    Cagnoni, Davide [ABB Switzerland Ltd., Corporate Research, CH-5405 Baden-Dättwil (Switzerland); MOX - Dipartimento di Matematica “F. Brioschi,” Politecnico di Milano, 20133 Milano (Italy); Agostini, Francesco; Christen, Thomas [ABB Switzerland Ltd., Corporate Research, CH-5405 Baden-Dättwil (Switzerland); Parolini, Nicola [MOX - Dipartimento di Matematica “F. Brioschi,” Politecnico di Milano, 20133 Milano (Italy); Stevanović, Ivica [ABB Switzerland Ltd., Corporate Research, CH-5405 Baden-Dättwil (Switzerland); Laboratory of Electromagnetics and Acoustics, Ecole Polytechnique Fédérale de Lausanne, CH-1015 Lausanne (Switzerland); Falco, Carlo de [MOX - Dipartimento di Matematica “F. Brioschi,” Politecnico di Milano, 20133 Milano (Italy); CEN - Centro Europeo di Nanomedicina, 20133 Milano (Italy)

    2013-12-21

    Ionic wind devices or electrostatic fluid accelerators are becoming of increasing interest as tools for thermal management, in particular for semiconductor devices. In this work, we present a numerical model for predicting the performance of such devices; its main benefit is the ability to accurately predict the amount of charge injected from the corona electrode. Our multiphysics numerical model consists of a highly nonlinear, strongly coupled set of partial differential equations including the Navier-Stokes equations for fluid flow, Poisson's equation for electrostatic potential, charge continuity, and heat transfer equations. To solve this system we employ a staggered solution algorithm that generalizes Gummel's algorithm for charge transport in semiconductors. Predictions of our simulations are verified and validated by comparison with experimental measurements of integral physical quantities, which are shown to closely match.

  17. Electric Field-Enhanced Catalytic Conversion of Methane: AN Experimental Study on the Effects of Corona Discharge on Methane Reactions

    Science.gov (United States)

    Marafee, Abdulathim M. J.

    The oxidative coupling of methane (OCM) is currently being actively studied for the production of higher hydrocarbons from natural gas. The present study concentrates on the oxidative conversion of methane in a high-pressure (one atmosphere), nonthermal plasma formed by corona discharge. Here, methyl radicals are formed by the reaction of methane with negatively-charged oxygen species created in the corona discharge. The results of methane conversion in the presence of both AC and DC corona discharges revealed that ethane and ethylene product selectivity is affected by electrode polarity, frequency, and oxygen partial pressure in the feed. Higher C_2 yields were obtained with the AC corona. All of the AC corona discharges specified here were initiated at room temperature (i.e., no oven or other heat source used), with temperature increases from 300 to 500^circC due to the exothermic gas discharge and exothermic reaction. A reaction mechanism is presented to explain the observed phenomena. The results suggest that AC and/or DC gas discharge techniques should be further studied for improved economics of methane conversion. The oxidative dehydrogenation of ethane in DC corona discharges was investigated. The atomic oxygen radicals initiated by corona discharges are thought to be active for the OXD of ethane. The selectivity to ethylene is affected by the reaction temperature, the DC applied voltage, voltage polarity, and the C_2H _6/O_2 ratio. The results of this study suggest the corona discharge process to be very efficient and selective in the oxidative dehydrogenation of ethane. The effects of DC corona discharge were examined in the presence of a typical OCM catalyst, Sr/La _2O_3. Experimental investigations have correspondingly been conducted, in which all reactive gases passed through a catalyst bed situated within the corona-induced plasma zone. The methane conversion and C_2 yield increased (with O_2 partial pressure) during the corona-enhanced catalytic

  18. Alkali ion migration between stacked glass plates by corona discharge treatment

    Science.gov (United States)

    Kawaguchi, Keiga; Suzuki, Toshio; Ikeda, Hiroshi; Sakai, Daisuke; Funatsu, Shiro; Uraji, Keiichiro; Yamamoto, Kiyoshi; Harada, Kenji; Nishii, Junji

    2015-05-01

    Corona discharge reflects the spatial migration of alkali ions over a gap between two glass plates. This study examined stacked glass plates containing different alkali ions treated with the corona discharge plasma generated by applied voltage of 4.5 kV at 200 °C. Protons generated at the anode electrode penetrate into the potassium-ion-containing upper glass plate, which is located 5 mm below the anode electrode. Potassium ions intruded into the lower glass plate containing sodium ions placed on the cathode electrode, even over a 1 mm gap separating the plates. Finally, the sodium ion discharged on the cathode electrode. The hydrogen atmosphere was effective at inhibiting the potassium ion reaction with ambient gases during the spatial migration between the two glass plates.

  19. Numerical simulation and experimental validation of a direct current air corona discharge under atmospheric pressure

    Institute of Scientific and Technical Information of China (English)

    Liu Xing-Hua; He Wei; Yang Fan; Wang Hong-Yu; Liao Rui-Jin; Xiao Han-Guang

    2012-01-01

    Air corona discharge is one of the critical problems associated with high-voltage equipment.Investigating the corona mechanism plays a key role in enhancing the electrical insulation performance.An improved self-consistent multi-component two-dimensional plasma hybrid model is presented for the simulation of a direct current atmospheric pressure corona discharge in air.The model is based on plasma hydrodynamic and chemical models,and includes 12 species and 26 reactions.In addition,the photoionization effect is introduced into the model.The simulation on a bar-plate electrode configuration with an inter-electrode gap of 5.0 mm is carried out.The discharge voltage-current characteristics and the current density distribution predicted by the hybrid model agree with the experimental measurements.In addition,the dynamics of volume charged species generation,discharge current waveform,current density distribution at an electrode,charge density,electron temperature,and electric field variations are investigated in detail based on the model.The results indicate that the model can contribute valuable insights into the physics of an air plasma discharge.

  20. Preliminary experiments on the growth of plants exposed to DC corona discharge in a hydroponics. Chokuryu corona hodenkadeno suiko sanbaini yoru shokubutsu seiikuno yobiteki kento

    Energy Technology Data Exchange (ETDEWEB)

    Shigemitsu, Tsukasa; Watanabe, Yasunori

    1988-01-01

    For the purpose of utilizing electrical phenomena to agriculture fields, preliminary experiments were carried out hydroponically to evaluate especially the effects of ion by DC corona discharge on the growth of plants such as lettuce or radish. The influences of various shapes of discharge electrodes on a water evaporation rate, ozone production rate and ion current change were studied, and the indirect stimulation effects on plants by more water evaporation under discharge, and the direct stimulation effects on plants with discharge by the electrode fixed 45cm above plants were studied. As a result, the water evaporation rate was 2 or 3 times more than that of control plots by positive or negative corona discharge, however, for the growth of plants, no remarkable direct or indirect stimulation effects by discharge were observed. As subjects, the clarification of water behavior change under discharge and of effects on plants in cellular level were pointed out to be necessary. (14 figs, 12 tabs, 12 refs)

  1. Characterisation of pulsed discharge in water

    Science.gov (United States)

    Kocik, Marek; Dors, Miroslaw; Podlinski, Janusz; Mizeraczyk, Jerzy; Kanazawa, Seiji; Ichiki, Ryuta; Sato, Takehiko

    2013-10-01

    In this paper, Schlieren photography technique has been applied for the visualization of the pressure field of a single-shot underwater pulsed discharge. A needle-to-plane electrode configuration submerged in distilled water was used. The detailed time- and space-resolved images of both streamers and pressure waves were captured. As a result, several phenomena, such as the phase change prior to the initiation of the discharge, primary and secondary streamers propagation, shock wave generation, and the bubble formation, were observed. From these observations, a scenario of multiple events from prebreakdown to post-discharge was proposed. The gas bubbles generated in discharge were used to visualize the electrohydrodynamic flow induced by the discharge. This work was presented on the occasion of the 13th International Symposium on High Pressure Low Temperature Plasma Chemistry (Hakone XIII).

  2. Force measurements in positive unipolar wire-to-plane corona discharges in air

    CERN Document Server

    de Haan, V O

    2004-01-01

    Measurements of force generated by a positive unipolar wire-to-plane corona discharge in air are compared with numerical simulations. The generated force does not depend on the ion or electron mobilities, preventing the influence of uncertainty and variation of these parameters. A method is described to simulate the voltage and charge distribution for a wire-to-plane set-up. This method enables the determination of the transition between unipolar and bipolar discharges. In the experimental set-up breakdown electric field of air reduces with increasing discharge current.

  3. Application of Excitation Function to the Prediction of RI Level Caused by Corona Discharge

    Institute of Scientific and Technical Information of China (English)

    ZHU Lingyu; JI Shengchang; HUI Sisi; GUO Jun; LI Yansong; FU Chenzhao

    2012-01-01

    Radio interference (RI), as an aftereffect of corona discharge, is an important research topic in the field of electromagnetic compatibility, where excitation function is applied broadly to the prediction of RI level. This paper presents the theory of excitation function method used in the RI level prediction. Then, some practical problems related to this method are discussed. The propagation procedure of corona current is solved by the phase-modal transformation, and the impedance matrix of multi transmission lines is calculated by a double logarithmic approximate model of Carson's Ground-Return impedance. At the same time, in order to calculate the RI level when total line corona is assumed, an analytical formula is deduced for integral operation. Based on the above solutions, an algorithm is presented and applied to the prediction of RI level of a practical overhead transmission line. Comparison of prediction and measurement results indicates that the algorithm proposed in this paper is effective and feasible.

  4. Surface oxide formation during corona discharge treatment of AA 1050 aluminium surfaces

    DEFF Research Database (Denmark)

    Minzari, Daniel; Møller, Per; Kingshott, Peter

    2008-01-01

    Atmospheric plasmas have traditionally been used as a non-chemical etching process for polymers, but the characteristics of these plasmas could very well be exploited for metals for purposes more than surface cleaning that is presently employed. This paper focuses on how the corona discharge...... process modifies aluminium AA 1050 surface, the oxide growth and resulting corrosion properties. The corona treatment is carried out in atmospheric air. Treated surfaces are characterized using XPS, SEM/EDS, and FIB-FESEM and results suggest that an oxide layer is grown, consisting of mixture of oxide...... and hydroxide. The thickness of the oxide layer extends to 150–300 nm after prolonged treatment. Potentiodynamic polarization experiments show that the corona treatment reduces anodic reactivity of the surface significantly and a moderate reduction of the cathodic reactivity....

  5. Absolute OH Number Density Measurements in Lean Fuel-Air Mixtures Excited by a Repetitively Pulsed Nanosecond Discharge

    Science.gov (United States)

    2013-01-01

    discharge filaments and near the electrode edges [9]. Instead of using absorption measurement, an atmospheric pressure flame generated by a Hencken...DuPont) is placed between each electrode and the channel wall, to reduce air gaps and prevent corona discharge outside the cell. In the present work...1 Absolute OH Number Density Measurements in Lean Fuel-Air Mixtures Excited by a Repetitively Pulsed Nanosecond Discharge Zhiyao Yin, Campbell D

  6. Evolution of electron beam pulses of short duration in the solar corona

    Science.gov (United States)

    Casillas-Pérez, G. A.; Jeyakumar, S.; Pérez-Enríquez, H. R.; Trinidad, M. A.

    2016-11-01

    Narrowband radio bursts with durations of the order of milliseconds, called spikes, are known to be associated with solar flares. In order to understand the particle beams responsible for the radio spike phenomena, evolution of electron beam pulses injected from a solar flare region into the corona is studied. Numerical integration of the Fokker-Planck (FP) equation is used to follow the evolution of the electron beam pulse. The simulations show that the short duration pulses lose most of their energy within a second of propagation into the corona. Electron beam with a small low energy cut off is thermalized faster than that with a high low energy cut off.

  7. A comparative summary on streamers of positive corona discharges in water and atmospheric pressure gases

    Science.gov (United States)

    Tachibana, Kunihide; Motomura, Hideki

    2015-07-01

    From an intention of summarizing present understandings of positive corona discharges in water and atmospheric pressure gases, we tried to observe streamers in those media by reproducing and complementing previously reported results under a common experimental setup. We used a point-to-plane electrode configuration with different combinations of electrode gap (7 and 19 mm length) and pulsed power sources (0.25 and 2.5 ɛs duration). The general features of streamers were similar and the streamer-to-spark transition was also observed in both the media. However, in the details large differences were observed due to inherent nature of the media. The measured propagation speed of streamers in water of 0.035 × 106 ms-1 was much smaller than the speed in gases (air, N2 and Ar) from 0.4 to 1.1 × 106 ms-1 depending on species. In He the discharge looked glow-like and no streamer was observed. The other characteristics of streamers in gases, such as inception voltage, number of branches and thickness did also depend on the species. The thickness and the length of streamers in water were smaller than those in gases. From the volumetric expansion of a streamer in water after the discharge, the molecular density within the streamer medium was estimated to be rarefied from the density of water by about an order of magnitude in the active discharge phase. We derived also the electron density from the analysis of Stark broadened spectral lines of H and O atoms on the order of 1025 m-3 at the earlier time of the streamer propagation. The analyzed background blackbody radiation, rotational temperature of OH band emission and population density of Cu atomic lines yielded a consistent temperature of the streamer medium between 7000 and 10 000 K. Using the present data with a combination of the analysis of static electric field and previously reported results, we discuss the reason for the relatively low streamer inception voltage in water as compared to the large difference in the

  8. Degradation of the endocrine disrupting chemicals (EDCs) carbamazepine, clofibric acid, and iopromide by corona discharge over water.

    Science.gov (United States)

    Krause, Holger; Schweiger, Bianca; Schuhmacher, Jörg; Scholl, Saskia; Steinfeld, Ute

    2009-04-01

    Common wastewater treatment plants often do not eliminate endocrine disrupting chemicals (EDCs). Aqueous solutions of three EDCs were treated with an enhanced corona discharge technology. The three EDCs were clofibric acid, a blood lipid regulator, carbamazepine, an antiepileptic drug, and iopromide, a contrast media. To simulate real conditions, EDC solutions containing landfill leachate were also used. In our setup, two barrier electrodes provided an atmospheric pressure corona discharge over a thin water film, in which the counter-electrode was submerged. Clofibric acid, carbamazepine, and iopromide were effectively removed from a single solution. After a treatment of 15min, there were no traces of iopromide estrogen activity either as a single substance or as degradation products when using an E-Screen Assay. Continuous treatment was compared with pulsed treatment using carbamazepine solutions mixed with pretreated landfill leachate. Best degradation results were achieved with a 500 W continuous duty cycle treatment. Counter-electrodes from materials such as boron doped diamond (BDD), titanium iridium oxide, and iron were investigated for their influences on the process effectivity. Significant improvements were achieved by using an enclosed reactor, BDD electrodes, and circulating only a fresh air or argon/air mixture as cooling gas through the barrier electrodes.

  9. Electro-Hydrodynamics and Kinetic Modeling of Dry and Humid Air Flows Activated by Corona Discharges

    Science.gov (United States)

    P. Sarrette, J.; Eichwald, O.; Marchal, F.; Ducasse, O.; Yousfi, M.

    2016-05-01

    The present work is devoted to the 2D simulation of a point-to-plane Atmospheric Corona Discharge Reactor (ACDR) powered by a DC high voltage supply. The corona reactor is periodically crossed by thin mono filamentary streamers with a natural repetition frequency of some tens of kHz. The study compares the results obtained in dry air and in air mixed with a small amount of water vapour (humid air). The simulation involves the electro-dynamics, chemical kinetics and neutral gas hydrodynamics phenomena that influence the kinetics of the chemical species transformation. Each discharge lasts about one hundred of a nanosecond while the post-discharge occurring between two successive discharges lasts one hundred of a microsecond. The ACDR is crossed by a lateral dry or humid air flow initially polluted with 400 ppm of NO. After 5 ms, the time corresponding to the occurrence of 50 successive discharge/post-discharge phases, a higher NO removal rate and a lower ozone production rate are found in humid air. This change is due to the presence of the HO2 species formed from the H primary radical in the discharge zone.

  10. Electro-Hydrodynamics and Kinetic Modeling of Dry and Humid Air Flows Activated by Corona Discharges

    Institute of Scientific and Technical Information of China (English)

    J.P.SARRETTE; O.EICHWALD; F.MARCHAL; O.DUCASSE; M.YOUSFI

    2016-01-01

    The present work is devoted to the 2D simulation of a point-to-plane Atmospheric Corona Discharge Reactor (ACDR) powered by a DC high voltage supply.The corona reactor is periodically crossed by thin mono filamentary streamers with a natural repetition frequency of some tens of kHz.The study compares the results obtained in dry air and in air mixed with a small amount of water vapour (humid air).The simulation involves the electro-dynamics,chemical kinetics and neutral gas hydrodynamics phenomena that influence the kinetics of the chemical species transformation.Each discharge lasts about one hundred of a nanosecond while the post-discharge occurring between two successive discharges lasts one hundred of a microsecond.The ACDR is crossed by a lateral dry or humid air flow initially polluted with 400 ppm of NO.After 5 ms,the time corresponding to the occurrence of 50 successive discharge/post-discharge phases,a higher NO removal rate and a lower ozone production rate are found in humid air.This change is due to the presence of the HO2 species formed from the H primary radical in the discharge zone.

  11. Alkali ion migration between stacked glass plates by corona discharge treatment

    Energy Technology Data Exchange (ETDEWEB)

    Kawaguchi, Keiga [Research Institute for Electronic Science, Hokkaido University, N20 W10, Kita-ku, Sapporo, Hokkaido 001-0020 (Japan); Suzuki, Toshio [Research Center, Asahi Glass Co., Ltd., 1150 Hazawa-cho, Kanagawa-ku, Yokohama, Kanagawa 221-8755 (Japan); Ikeda, Hiroshi [Art, Science and Technology Center for Cooperative Research, Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan); Sakai, Daisuke [Department of Electrical and Electronic Engineering, Kitami Institute of Technology, 165 Koen-cho, Kitami, Hokkaido 090-8507 (Japan); Funatsu, Shiro; Uraji, Keiichiro [Production Technology Center, Asahi Glass Co., Ltd., 1-1 Suehiro-cyo, Tsurumiku, Yokohama, Kanagawa 230-0045 (Japan); Yamamoto, Kiyoshi [Research Center, Asahi Glass Co., Ltd., 1150 Hazawa-cho, Kanagawa-ku, Yokohama, Kanagawa 221-8755 (Japan); Harada, Kenji [Department of Computer Science, Kitami Institute of Technology, 165 Koen-cho, Kitami, Hokkaido 090-8507 (Japan); Nishii, Junji, E-mail: nishii@es.hokudai.ac.jp [Research Institute for Electronic Science, Hokkaido University, N20 W10, Kita-ku, Sapporo, Hokkaido 001-0020 (Japan)

    2015-05-30

    Highlights: • Two stacked glass plates with a 1 mm gap were treated by corona discharge. • Spatial migration of alkali ion over the gap was demonstrated. • Hydrogen gas was necessary for uniform migration. • Surface modification was done with this process without high temperature or vacuum. - Abstract: Corona discharge reflects the spatial migration of alkali ions over a gap between two glass plates. This study examined stacked glass plates containing different alkali ions treated with the corona discharge plasma generated by applied voltage of 4.5 kV at 200 °C. Protons generated at the anode electrode penetrate into the potassium-ion-containing upper glass plate, which is located 5 mm below the anode electrode. Potassium ions intruded into the lower glass plate containing sodium ions placed on the cathode electrode, even over a 1 mm gap separating the plates. Finally, the sodium ion discharged on the cathode electrode. The hydrogen atmosphere was effective at inhibiting the potassium ion reaction with ambient gases during the spatial migration between the two glass plates.

  12. Decontamination effects of low-temperature plasma generated by corona discharge. Part II: new insights.

    Science.gov (United States)

    Scholtz, V; Julák, J; Kríha, V; Mosinger, J; Kopecká, S

    2007-01-01

    The second part of our paper presents the results of experiments with the decontamination of surfaces by low-temperature plasma generated by corona discharge in air at atmospheric pressure. A simple device is described and the effects of the corona discharge on model microorganisms, viz. the yeast Candida albicans, Gram-negative bacteria Escherichia coli, Enterobacter aerogenes, Neisseria sicca, Stenotrophomonas maltophilia, Gram-positive bacteria Deinococcus radiodurans, Enterococcus faecium, Staphylococcus epidermidis, Streptococcus sanguinis, and vegetative and spore forms of Geobacillus stearothermophilus are discussed. A similar microbicidal effect after about one-minute exposure was observed in all vegetative forms of the microorganisms. Measurement in growth inhibition zones on a semisolid medium was used to determine the dependence of the microbicidal effect on exposure time and the distance between electrodes. Counting of colonies served to assess the microbicidal effect of the discharge on contaminated inert surfaces observable after more than 1 min exposure. Geobacillus stearothermophilus spores were found to have several times lower susceptibility to the action of the discharge and the microbicidal effect was observed only after an 8 min exposure. Reaction with the iodide reagent did not unambiguously demonstrate the difference between ozone and singlet oxygen as presumed active components of the corona. The area distribution of reactive oxygen species was determined; it was found to differ from the Wartburg law depending on exposure time. Qualitative evidence was obtained on the penetration of the reactive oxygen species into the semisolid medium.

  13. [Morphology determination of multi-needle bipolar corona discharge by OES].

    Science.gov (United States)

    Chen, Hai-Feng; Su, Peng-Hao; Zhu, Yi-Min

    2009-01-01

    Using the method of OES (optical emission spectrum) for measuring N2 emission spectrum, the spacial distribution of energetic electrons in multi-needle bipolar corona discharge at atmospheric pressure was investigated. According to the distribution of N2 second positive band's intensity ISPB, the outline of ionisation region was drawn accurately. The relationship between ISPB and discharge current I was obtained through the sum of ISPB. There are two ionisation regions in the multi-needle bipolar corona discharge. One is near the HV electrode and the other is near the grounded electrode. The ionisation region exists around the needlepoint within 2-3 mm. The volume of ionisation region becomes big with the applied voltage U increasing. The ionisation region of negative corona is bigger than that of positive corona. Near the HV discharge electrode, the outline of electron avalanche is similar to the configuration of electric field lines in the ionisation region, so the electron avalanche along the axis direction of needle develops farther than that along the radial direction. The electric field in the migration area is weak, and the distribution of space charges is large along the radial direction. The sum of ISPB in each ionisation region is second order linear with I, but the quadratic coefficient is very small. So the sum of ISPB is nearly linear with I, the distribution of ISPB is corresponding to the density distribution of energetic electrons. So the charged particles forming the discharge current in ionisation region are electrons. No emission spectrum of N2 can be measured in migration area, so there is no energetic electron. The energetic electrons only exist in ionisation region and the charged particles in migration area are ions.

  14. Ozone production by corona discharges during a convective event in DISCOVER-AQ Houston

    Science.gov (United States)

    Kotsakis, Alexander; Morris, Gary A.; Lefer, Barry; Jeon, Wonbae; Roy, Anirban; Minschwaner, Ken; Thompson, Anne M.; Choi, Yunsoo

    2017-07-01

    An ozonesonde launched near electrically active convection in Houston, TX on 5 September 2013 during the NASA DISCOVER-AQ project measured a large enhancement of ozone throughout the troposphere. A separate ozonesonde was launched from Smith Point, TX (∼58 km southeast of the Houston site) at approximately the same time as the launch from Houston and did not measure that enhancement. Furthermore, ozone profiles for the descent of both sondes agreed well with the ascending Smith Point profile, suggesting a highly localized event in both space and time in which an anomalously large enhancement of 70-100 ppbv appeared in the ascending Houston ozonesonde data. Compared to literature values, such an enhancement appears to be the largest observed to date. Potential sources of the localized ozone enhancement such as entrainment of urban or biomass burning emissions, downward transport from the stratosphere, photochemical production from lightning NOx, and direct ozone production from corona discharges were investigated using model simulations. We conclude that the most likely explanation for the large ozone enhancement is direct ozone production by corona discharges. Integrating the enhancement seen in the Houston ozone profile and using the number of electrical discharges detected by the NLDN (or HLMA), we estimate a production of 2.48 × 1028 molecules of ozone per flash which falls within the range of previously recorded values (9.89 × 1026-9.82 × 1028 molecules of ozone per flash). Since there is currently no parameterization for the direct production of ozone from corona discharges we propose the implementation of an equation into a chemical transport model. Ultimately, additional work is needed to further understand the occurrence and impact of corona discharges on tropospheric chemistry on short and long timescales.

  15. Pulsed electrical discharge in conductive solution

    Science.gov (United States)

    Panov, V. A.; Vasilyak, L. M.; Vetchinin, S. P.; Pecherkin, V. Ya; Son, E. E.

    2016-09-01

    Electrical discharge in a conductive solution of isopropyl alcohol in tap water (330 μ S cm-1) has been studied experimentally applying high voltage millisecond pulses (rise time  ˜0.4 μ \\text{s} , amplitude up to 15 kV, positive polarity) to a pin anode electrode. Dynamic current-voltage characteristics synchronized with high-speed images of the discharge were studied. The discharge was found to develop from high electric field region in the anode vicinity where initial conductive current with density  ˜100 A cm-2 results in fast heating and massive nucleation of vapor bubbles. Discharges in nucleated bubbles then produce a highly conductive plasma region and facilitate overheating instability development with subsequent formation of a thermally ionized plasma channel. The measured plasma channel propagation speed was 3-15 m s-1. A proposed thermal model of plasma channel development explains the low observed plasma channel propagation speed.

  16. Ionic Wind Phenomenon and Charge Carrier Mobility in Very High Density Argon Corona Discharge Plasma

    Science.gov (United States)

    Nur, M.; Bonifaci, N.; Denat, A.

    2014-04-01

    Wind ions phenomenon has been observed in the high density argon corona discharge plasma. Corona discharge plasma was produced by point to plane electrodes and high voltage DC. Light emission from the recombination process was observed visually. The light emission proper follow the electric field lines that occur between point and plane electrodes. By using saturation current, the mobilities of non-thermal electrons and ions have been obtained in argon gas and liquid with variation of density from 2,5 1021 to 2 1022 cm-3. In the case of ions, we found that the behaviour of the apparent mobility inversely proportional to the density or follow the Langevin variation law. For non-thermal electron, mobility decreases and approximately follows a variation of Langevin type until the density <= 0,25 the critical density of argon.

  17. Dimensional analysis of detrimental ozone generation by positive wire-to-plate corona discharge in air

    Science.gov (United States)

    Bo, Z.; Chen, J. H.

    2010-02-01

    The dimensional analysis technique is used to formulate a correlation between ozone generation rate and various parameters that are important in the design and operation of positive wire-to-plate corona discharges in indoor air. The dimensionless relation is determined by linear regression analysis based on the results from 36 laboratory-scale experiments. The derived equation is validated by experimental data and a numerical model published in the literature. Applications of such derived equation are illustrated through an example selection of the appropriate set of operating conditions in the design/operation of a photocopier to follow the federal regulations of ozone emission. Finally, a new current-voltage characteristic equation is proposed for positive wire-to-plate corona discharges based on the derived dimensionless equation.

  18. Experimental investigation and numerical modelling of positive corona discharge: ozone generation

    Science.gov (United States)

    Yanallah, K; Pontiga, F; Fernández-Rueda, A; Castellanos, A

    2009-03-01

    The spatial distribution of the species generated in a wire-cylinder positive corona discharge in pure oxygen has been computed using a plasma chemistry model that includes the most significant reactions between electrons, ions, atoms and molecules. The plasma chemistry model is included in the continuity equations of each species, which are coupled with Poisson's equation for the electric field and the energy conservation equation for the gas temperature. The current-voltage characteristic measured in the experiments has been used as an input data to the numerical simulation. The numerical model is able to reproduce the basic structure of the positive corona discharge and highlights the importance of Joule heating on ozone generation. The average ozone density has been computed as a function of current intensity and compared with the experimental measurements of ozone concentration determined by UV absorption spectroscopy.

  19. Experimental investigation and numerical modelling of positive corona discharge: ozone generation

    Energy Technology Data Exchange (ETDEWEB)

    Yanallah, K; Castellanos, A [Departamento de Electronica y Electromagnetismo, Universidad de Sevilla (Spain); Pontiga, F; Fernandez-Rueda, A [Departamento de FIsica Aplicada II, Universidad de Sevilla (Spain)

    2009-03-21

    The spatial distribution of the species generated in a wire-cylinder positive corona discharge in pure oxygen has been computed using a plasma chemistry model that includes the most significant reactions between electrons, ions, atoms and molecules. The plasma chemistry model is included in the continuity equations of each species, which are coupled with Poisson's equation for the electric field and the energy conservation equation for the gas temperature. The current-voltage characteristic measured in the experiments has been used as an input data to the numerical simulation. The numerical model is able to reproduce the basic structure of the positive corona discharge and highlights the importance of Joule heating on ozone generation. The average ozone density has been computed as a function of current intensity and compared with the experimental measurements of ozone concentration determined by UV absorption spectroscopy.

  20. Ionic wind generation by a wire-cylinder-plate corona discharge in air at atmospheric pressure

    OpenAIRE

    Colas, Dorian,; Ferret, Antoine; Pai, David,; Lacoste, Deanna,; Laux, C.

    2010-01-01

    International audience; A wire-cylinder-plate electrode configuration is presented to generate ionic wind with a dc corona discharge in air at atmospheric pressure. The objective of the work is to maximize the power supplied to the flow in order to increase acceleration while avoiding breakdown. Thus, the proposed experimental setup addresses the problem of decoupling the mechanism of ion generation from that of ion acceleration. Using a wire-plate configuration as a reference, we have focuse...

  1. A self-consistent model of ionic wind generation by negative corona discharges in air with experimental validation

    Science.gov (United States)

    Chen, She; Nobelen, J. C. P. Y.; Nijdam, S.

    2017-09-01

    Ionic wind is produced by a corona discharge when gaseous ions are accelerated in the electric field and transfer their momentum to neutral molecules by collisions. This technique is promising because a gas flow can be generated without the need for moving parts and can be easily miniaturized. The basic theory of ionic wind sounds simple but the details are far from clear. In our experiment, a negative DC voltage is applied to a needle-cylinder electrode geometry. Hot wire anemometry is used to measure the flow velocity at the downstream exit of the cylinder. The flow velocity fluctuates but the average velocity increases with the voltage. The current consists of a regular train of pulses with short rise time, the well-known Trichel pulses. To reveal the ionic wind mechanism in the Trichel pulse stage, a three-species corona model coupled with gas dynamics is built. The drift-diffusion equations of the plasma together with the Navier–Stokes equations of the flow are solved in COMSOL Multiphysics. The electric field, net number density of charged species, electrohydrodynamic (EHD) body force and flow velocity are calculated in detail by a self-consistent model. Multiple time scales are employed: hundreds of microseconds for the plasma characteristics and longer time scales (∼1 s) for the flow behavior. We found that the flow velocity as well as the EHD body force have opposite directions in the ionization region close to the tip and the ion drift region further away from the tip. The calculated mean current, Trichel pulse frequency and flow velocity are very close to our experimental results. Furthermore, in our simulations we were able to reproduce the mushroom-like minijets observed in experiments.

  2. Effects of pulse-to-pulse residual species on discharges in repetitively pulsed discharges through packed bed reactors

    Science.gov (United States)

    Kruszelnicki, Juliusz; Engeling, Kenneth W.; Foster, John E.; Kushner, Mark J.

    2016-09-01

    Atmospheric pressure dielectric barrier discharges (DBDs) sustained in packed bed reactors (PBRs) are being investigated for conversion of toxic and waste gases, and CO2 removal. These discharges are repetitively pulsed having varying flow rates and internal geometries, which results in species from the prior pulse still being in the discharge zone at the time the following discharge pulse occurs. A non-negligible residual plasma density remains, which effectively acts as preionization. This residual charge changes the discharge properties of subsequent pulses, and may impact important PBR properties such as chemical selectivity. Similarly, the residual neutral reactive species produced during earlier pulses will impact the reaction rates on subsequent pulses. We report on results of a computational investigation of a 2D PBR using the plasma hydrodynamics simulator nonPDPSIM. Results will be discussed for air flowing though an array of dielectric rods at atmospheric pressure. The effects of inter-pulse residual species on PBR discharges will be quantified. Means of controlling the presence of residual species in the reactor through gas flow rate, pulse repetition, pulse width and geometry will be described. Comparisons will be made to experiments. Work supported by US DOE Office of Fusion Energy Science and the National Science Foundation.

  3. 线板式脉冲电晕放电反应器OH自由基二维分布的光谱学研究%Spectroscopic Diagnosis of Two-Dimensional Distribution of OH Radicals in Wire-Plate Pulsed Corona Discharge Reactor

    Institute of Scientific and Technical Information of China (English)

    江建平; 骆仲泱; 轩俭勇; 赵磊; 方梦祥; 高翔

    2015-01-01

    脉冲电晕放电过程中OH自由基等活性基团的空间分布特性对燃煤烟气污染物的氧化脱除具有重要作用。为了探索脉冲电晕放电污染物控制技术的机理,采用激光诱导荧光法检测线板式反应器内部脉冲电晕放电过程中OH自由基的空间二维分布特性,主要研究了不同相对湿度和含氧量对OH自由基空间二维分布特性的影响。实验表明,脉冲电晕放电过程中OH自由基主要存在于线电极下方的区域中,并以线电极为中心面向板电极呈现扇形分布,并且其扇形分布区域的纵向长度和横向宽度的最大值均小于1 cm ;相对湿度的增大有利于OH自由基的生成,促进OH自由基空间二维分布区域面积的扩大,当相对湿度为65%时O H自由基的空间二维分布区域面积达到最大值;当含氧量为2%时最有利于O H自由基的生成,并且O H自由基的空间二维分布区域面积达到最大值,当含氧量超过15%时对O H自由基的生成及其空间二维分布主要起抑制作用。同时,相对湿度和含氧量的增加均提高了激发态OH自由基中猝灭部分所占的比重,从而降低了OH自由基的荧光产率,其中含氧量对OH自由基荧光产率和OH自由基空间二维分布的影响作用大于相对湿度。%Pulsed corona discharge in atmosphere has been widely regarded as an efficient flue gas treatment technology for the generation of active radical species ,such as the OH radicals .The spatial distribution of OH radicals generated by pulsed corona discharge plays an important role in decomposing pollutants .The two‐dimensional (2‐D) distribution of OH radicals of positive wire–plate pulsed corona discharge was detected using laser‐induced fluorescence (LIF) .The influence of relative humidity (RH) and oxygen concentration on the 2‐D distribution of OH radicals were investigated .The results indicated that the 2‐D dis‐tribution of

  4. Line Shape Modeling for the Diagnostic of the Electron Density in a Corona Discharge

    Directory of Open Access Journals (Sweden)

    Joël Rosato

    2017-09-01

    Full Text Available We present an analysis of spectra observed in a corona discharge designed for the study of dielectrics in electrical engineering. The medium is a gas of helium and the discharge was performed at the vicinity of a tip electrode under high voltage. The shape of helium lines is dominated by the Stark broadening due to the plasma microfield. Using a computer simulation method, we examine the sensitivity of the He 492 nm line shape to the electron density. Our results indicate the possibility of a density diagnostic based on passive spectroscopy. The influence of collisional broadening due to interactions between the emitters and neutrals is discussed.

  5. Determination of alcohol compounds using corona discharge ion mobility spectrometry

    Institute of Scientific and Technical Information of China (English)

    HAN Hai-yan; HUANG Guo-dong; JIN Shun-ping; ZHENG Pei-chao; XU Guo-hua; LI Jian-quan; WANG Hong-mei; CHU Yan-nan

    2007-01-01

    Ion mobility spectrometry (IMS) is a very fast, highly sensitive, and inexpensive technique, it permits efficient monitoring of volatile organic compounds like alcohols. In this article, positive ion mobility spectra for six alcohol organic compounds have been systematically studied for the first time using a high-resolution IMS apparatus equipped with a discharge ionization source. Utilizing protonated water cluster ions (H2O)nH+ as the reactant ions and clean air as the drift gas, alcohol organic compounds, ethanol, 1-propanol, 2-propanol, 1-butanol, 1-pentanol and 2-octanol, all exhibit product ion characteristic peaks in their respective ion mobility spectrometry, that is a result of proton transfer reactions between the alcohols and reaction ions (H2O)nH+. The mixture of these alcohols, including two isomers, has been detected, and the result shows that they can also be distinguished effectively in the ion mobility spectrum. The reduced mobility values have been determined, which are in very well agreement with the traditional 63Ni-IMS experimental values. The exponential dilution method was used to calibrate the alcohol concentrations, and a detection limit available for the alcohols is in order of magnitude of a few ng/L.

  6. Atmospheric pressure chemical ionization of explosives using alternating current corona discharge ion source.

    Science.gov (United States)

    Usmanov, D T; Chen, L C; Yu, Z; Yamabe, S; Sakaki, S; Hiraoka, K

    2015-04-01

    The high-sensitive detection of explosives is of great importance for social security and safety. In this work, the ion source for atmospheric pressure chemical ionization/mass spectrometry using alternating current corona discharge was newly designed for the analysis of explosives. An electromolded fine capillary with 115 µm inner diameter and 12 mm long was used for the inlet of the mass spectrometer. The flow rate of air through this capillary was 41 ml/min. Stable corona discharge could be maintained with the position of the discharge needle tip as close as 1 mm to the inlet capillary without causing the arc discharge. Explosives dissolved in 0.5 µl methanol were injected to the ion source. The limits of detection for five explosives with 50 pg or lower were achieved. In the ion/molecule reactions of trinitrotoluene (TNT), the discharge products of NOx (-) (x = 2,3), O3 and HNO3 originating from plasma-excited air were suggested to contribute to the formation of [TNT - H](-) (m/z 226), [TNT - NO](-) (m/z 197) and [TNT - NO + HNO3 ](-) (m/z 260), respectively. Formation processes of these ions were traced by density functional theory calculations. Copyright © 2015 John Wiley & Sons, Ltd.

  7. Charge mitigation techniques using glow and corona discharges for advanced gravitational wave detectors

    Energy Technology Data Exchange (ETDEWEB)

    Campsie, P; Cunningham, L; Hendry, M; Hough, J; Reid, S; Rowan, S; Hammond, G D, E-mail: p.campsie@physics.gla.ac.uk [SUPA , Institute for Gravitational Research, School of Physics and Astronomy, University of Glasgow, Glasgow, G12 8QQ (United Kingdom)

    2011-11-07

    Charging of silica test masses in gravitational wave detectors could potentially become a significant low-frequency noise source for advanced detectors. Charging noise has already been observed and confirmed in the GEO600 detector and is thought to have been observed in one of the LIGO detectors. In this paper, two charge mitigation techniques using glow and corona discharges were investigated to create repeatable and robust procedures. The glow discharge procedure was used to mitigate charge under vacuum and would be intended to be used in the instance where an optic has become charged while the detector is in operation. The corona discharge procedure was used to discharge samples at atmospheric pressure and would be intended to be used to discharge the detector optics during the cleaning of the optics. Both techniques were shown to reduce both polarities of surface charge on fused silica to a level that would not limit advanced LIGO. Measurements of the transmission of samples that had undergone the charge mitigation procedures showed no significant variation in transmission, at a sensitivity of {approx} 200 ppm, in TiO{sub 2}-doped Ta{sub 2}O{sub 5}/SiO{sub 2} multi-layer coated fused silica.

  8. Modeling and characterization of field-enhanced corona discharge in ozone-generator diode

    Science.gov (United States)

    Patil, Jagadish G.; Vijayan, T.

    2010-02-01

    Electric field enhanced corona plasma discharge in ozone generator diode of axial symmetry has been investigated and characterized in theory. The cathode K of diode is made of a large number of sharpened nozzles arranged on various radial planes on the axial mast and pervaded in oxygen gas inside the anode cup A, produces high fields over MV/m and aids in the formation of a corona plume of dense ozone cloud over the cathode surface. An r-z finite difference scheme has been devised and employed to numerically determine the potential and electric field distributions inside the diode. The analyses of cathode emissions revealed a field emission domain conformed to modified Child-Langmuir diode-current. Passage of higher currents (over μA) in shorter A-K gaps d gave rise to cathode heated plasma extending from the corona to Saha regimes depending on local temperature. Plasma densities of order 102-106 m-3 are predicted in these. For larger d however, currents are smaller and heating negligible and a negative corona favoring ozone formation is attained. High ozone yields about 20 per cent of oxygen input is predicted in this domain. The generator so developed will be applied to various important applications such as, purification of ambient air /drinking water, ozone therapy, and so on.

  9. Pulsed microhollow cathode discharge excimer sources

    Science.gov (United States)

    Moselhy, Mohamed; Shi, Wenhui; Strak, Robert H.; Schoenbach, Karl H.

    2001-10-01

    Microhollow cathode discharges (MHCDs) are non-equilibrium, high-pressure gas discharges between perforated electrodes separated by a dielectric layer. Typical dimensions for the electrode foil thickness and hole diameter are 100 μm. Direct current experiments in xenon, argon, neon, helium, argon fluoride, and xenon chloride [1,2] have been performed. The excimer efficiency varies between 1 % and 9 %. Pulsed operation allowed us to increase the current from 8 mA (dc) to approximately 80 mA (pulsed with a pulse width of 700 μs), limited by the onset of instabilities. The total excimer power was found to increase linearly with current, however, the radiant emittance and efficiency stayed constant. Reducing the pulse duration into the nanosecond range allowed us to increase the current into the ampere range. The maximum measured excimer power was 2.75 W per microdischarge. The maximum radiant emittance was 15 W/cm^2 and the efficiency reached values of 20 %. This effect is assumed to be due to non-equilibrium electron heating in the high-pressure plasma [3]. This work was supported by the National Science Foundation under grant # CTS0078618. 1. Karl H. Schoenbach, Ahmed El-Habachi, Mohamed M. Moselhy, Wenhui Shi, and Robert H. Stark, Physics of Plasmas 7, 2186 (2000). 2. P. Kurunczi, J. Lopez, H. Shah, and K. Becker, Int. J. Mass Spectrom. 205, 277 (2001). 3. Robert H. Stark and Karl H. Schoenbach, J. Appl. Phys. 89, 3568 (2001).

  10. Time-lag properties of corona streamer discharges between impulse sphere and dc needle electrodes under atmospheric air conditions.

    Science.gov (United States)

    Okano, Daisuke

    2013-02-01

    In this study of corona streamer discharges from an impulse generator using a dc power supply, the relationship of the discharge time-lag with the dc bias voltage between the sphere-to-needle electrodes under atmospheric conditions is investigated. Devices utilizing corona discharges have been used to purify air or water, destroy bacteria, and to remove undesirable substances, and in order to achieve fast response times and high power efficiencies in such devices, it is important to minimize the time-lag of the corona discharge. Our experimental results show that (a) the discharge path of a negatively biased needle electrode will be straighter than that of a positively biased needle and (b) the discharge threshold voltage in both the positive and the negative needle electrodes is nearly equal to 33 kV. By expressing the discharge voltage as a power function of time-lag, the extent of corona generation can be quantitatively specified using the exponent of this power function. The observed behavior of a corona streamer discharge between the negative spherical and the positive needle electrodes indicates that the largest power exponent is associated with the shortest time-lag, owing to the reduction in the statistical time-lag in the absence of a formative time-lag.

  11. Time-lag properties of corona streamer discharges between impulse sphere and dc needle electrodes under atmospheric air conditions

    Science.gov (United States)

    Okano, Daisuke

    2013-02-01

    In this study of corona streamer discharges from an impulse generator using a dc power supply, the relationship of the discharge time-lag with the dc bias voltage between the sphere-to-needle electrodes under atmospheric conditions is investigated. Devices utilizing corona discharges have been used to purify air or water, destroy bacteria, and to remove undesirable substances, and in order to achieve fast response times and high power efficiencies in such devices, it is important to minimize the time-lag of the corona discharge. Our experimental results show that (a) the discharge path of a negatively biased needle electrode will be straighter than that of a positively biased needle and (b) the discharge threshold voltage in both the positive and the negative needle electrodes is nearly equal to 33 kV. By expressing the discharge voltage as a power function of time-lag, the extent of corona generation can be quantitatively specified using the exponent of this power function. The observed behavior of a corona streamer discharge between the negative spherical and the positive needle electrodes indicates that the largest power exponent is associated with the shortest time-lag, owing to the reduction in the statistical time-lag in the absence of a formative time-lag.

  12. High-voltage electrode optimization towards uniform surfacetreatment by a pulsed volume discharge

    OpenAIRE

    Ponomarev, A. V.; Pedos, M. S.; Scherbinin, S. V.; Mamontov, Y. I.; Ponomarev, Sergey Viktorovich

    2015-01-01

    In this study, the shape and material of the high-voltage electrode of an atmospheric pressure plasma generation system were optimised. The research was performed with the goal of achieving maximum uniformity of plasma treatment of the surface of the low-voltage electrode with a diameter of 100 mm. In order to generate low-temperature plasma with the volume of roughly 1 cubic decimetre, a pulsed volume discharge was used initiated with a corona discharge. The uniformity of the plasma in the r...

  13. Comparative Analysis of Experiment Treating Benzene and CEES by Pulse Corona Plasma

    Institute of Scientific and Technical Information of China (English)

    Yan Xuefeng; Hu Zhen

    2005-01-01

    Based on an experiment treating benzene and 2-chloroethyl ethyl sulfide ( CEES )by pulse corona induced-plasma, the similarities and differences found in the experimental data and analytical results are analyzed in a comparative manner in this paper. The theory applied is also discussed.

  14. Self-pulsing of a micro thin cathode discharge

    CERN Document Server

    Gebhardt, Markus; Hemke, Torben; Brinkmann, Ralf Peter; Mussenbrock, Thomas

    2011-01-01

    Microplasmas operated at atmospheric pressure show a number of peculiar dynamic phenomena. One of these phenomena is self-pulsing, which is characterized by intrinsic pulsing behavior of a DC driven plasma discharge. This work focuses on the numerical simulation of self-pulsing in a micro thin cathode discharge operated in atmospheric pressure argon. By means of a hybrid plasma model we show self-pulsing of the discharge in the expected MHz frequency range and described its actual origin.

  15. Improvement in ionization efficiency of direct analysis in real time-mass spectrometry (DART-MS) by corona discharge.

    Science.gov (United States)

    Sekimoto, Kanako; Sakakura, Motoshi; Kawamukai, Takatomo; Hike, Hiroshi; Shiota, Teruhisa; Usui, Fumihiko; Bando, Yasuhiko; Takayama, Mitsuo

    2016-08-02

    Herein it is shown that a combination of direct analysis in real time (DART) with a corona discharge system consisting of only a needle electrode easily improves DART ionization efficiency. Positive and negative DC corona discharges led to a formation of abundant excited helium atoms as well as the reactant ions H3O(+)(H2O)n and O2˙(-) in the DART analyte ionization area. These phenomena resulted in an increase in the absolute intensities of (de)protonated analytes by a factor of 2-20 over conventional DART. The other analyte ions detected in this corona-DART system (i.e., molecular ions, fragment ions, oxygenated (de)protonated analytes, dehydrogenated deprotonated analytes, and negative ion adducts) were quite similar to those obtained from DART alone. This indicates a lack of side reactions due to the corona discharge. The change in the relative intensities of individual analyte-related ions due to the combination of a corona discharge system with DART suggests that there is no effect of the abundant excited helium in the analyte ionization area on the fragmentation processes or enhancement of oxidation due to hydroxyl radicals HO˙. Furthermore, it was found that the corona-DART combination can be applied to the highly sensitive analysis of n-alkanes, in which the alkanes are ionized as positive ions via hydride abstraction and oxidation, independent of the type of alkane or the mass spectrometer used.

  16. Negative Corona Discharge Ion Source Under Ambient Conditions with Mini Line-cylinder Electrodes

    Institute of Scientific and Technical Information of China (English)

    Kun Liu; Fei Tang; Xiao-hao Wang; Liang Zhang; Xue-ye Wei

    2009-01-01

    A novel ambient negative corona discharge ion source with mini line-cylinder electrodes is designed. The diameters of inner and outer electrode are 0.16 and 4 mm respectively. With a special assembly method, a perfect coaxiality of the two electrodes is obtained. An injection system utilizing a temperature control technique, achieves a constant and stable concentra-tion of the sample, which is critical to the experiment. The formulas of the corona onset voltage of line-cylinder electrodes are also introduced. The experiment results show that negative substances such as formic acid and acetic acid can be ionized under ambient con-ditions. When combined with micro electrical mechanical system fabrication process, the volume of the ion source can be reduced dramatically, but there is an undesirable surface discharge. To solve the surface discharge problem, an improved structure was designed and tested. The simplicity of the interface of the ion source makes it suitable for mass spec-trometer, micro mass spectrometer, ion mobility spectrometer, and high-field asymmetric waveform ion mobility spectrometer applications.

  17. 空气中电晕放电与绝缘液体中流注放电的测量和分析%Time Sequential and Phase-resolved Measurement and Analysis of Corona Discharge in Air and Streamer Discharge in Insulating Liquid

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Insulation is one of the most important parts in a high voltage equipment. There are gaseous, liquid and solid insulations which are commonly used. In a high voltage transformer for example the insulating materials are all used. During operation of a high voltage equipment high electric stress may occur. Under extreme condition failure of the insulation may take place. Excessive electric field in air may cause corona discharges while in liquid insulation discharges may take place in the form of streamer. This paper reports experimental results on the corona and streamer discharges in air and silicone oil. The discharges were artificially generated around a needle tip in a needle-plane electrode system with gap length of 4 mm under sinusoidal and triangular voltages. The needle was made of steel with tip radius of 3 μm and curvature angle of 30°. The needle was made by Ogura Jewelry. The discharge pulses were measured using personal-computer based partial discharge (PD) measurement system with sensitivity of better than 0.5 pC. The system is able to measure discharge in time sequential. Phase-resolved analysis of the discharges was done to interpret the physical processes behind the discharges. The experimental results showed that corona discharges took place at negative half cycles. The discharges were concentrated around 270° of phase angle of applied voltage. The discharge magnitude and discharge number of corona clearly dependent on the instantaneous of applied voltage. These were strongly supported by the application of triangular voltage. Streamer discharges occurred at both positive and negative half cycles. The discharges pulses concentrated around the peak of applied voltage at phase angle of 90° and 270°. Experimental results under sinusoidal and triangular voltages revealed that streamer discharge magnitude as well as probability of occurrence was strongly dependent on the instantaneous applied voltage.

  18. Synthesis of carbon nanotube array using corona discharge plasma-enhanced chemical vapor deposition

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A corona discharge plasma-enhanced chemical vapor deposition with the features of atmospheric pressure and low temperature has been developed to synthesize the carbon nanotube array. The array was synthesized from methane and hydrogen mixture in anodic aluminum oxide template channels in that cobalt was electrodeposited at the bottom. The characterization results by the scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and Raman spectroscopy indicate that the array consists of carbon nanotubes with the diameter of about 40 nm and the length of more than 4 -m, and the carbon nanotubes are mainly restrained within the channels of templates.

  19. First gaseous boronization during pulsed discharge cleaning

    Energy Technology Data Exchange (ETDEWEB)

    Ko, J., E-mail: jinseok@nfri.re.kr [Department of Physics, University of Wisconsin, Madison, WI (United States); Den Hartog, D.J.; Goetz, J.A.; Weix, P.J.; Limbach, S.T. [Department of Physics, University of Wisconsin, Madison, WI (United States)

    2013-01-15

    The first successful gaseous boronization during a pulsed discharge is reported. Sublimation of o-carborane (C{sub 2}B{sub 10}H{sub 12}) combined with pulsed discharge plasmas with a repetition rate of 1 Hz is used to produce a hard boron-containing coating for reversed field pinch (RFP) plasmas in the Madison Symmetric Torus. X-ray photoelectron spectroscopy with Ar ion beam etching for silicon coupons installed at the plasma boundary shows about 60% boron concentration in the deposited layer. Both profilometer and scanning electron microscope analyses of the silicon coupons imply a strong toroidally non-uniform deposition depending on the location of the o-carborane injection. The layer thickness ranges from 50 to 300 nm. Ellipsometry calibrated with the profilometer results yields a refractive index of 2.2-2.3 for the films. The high refractive index implies that the coating is hard and has a well-ordered morphology. A reduction in wall recycling has consistently been observed after all boronization sessions. Comparison of the X-ray spectra in standard RFP plasmas before and after boronization indicates a slight decrease in the effective ionic charge.

  20. First gaseous boronization during pulsed discharge cleaning

    Science.gov (United States)

    Ko, J.; Den Hartog, D. J.; Goetz, J. A.; Weix, P. J.; Limbach, S. T.

    2013-01-01

    The first successful gaseous boronization during a pulsed discharge is reported. Sublimation of o-carborane (C2B10H12) combined with pulsed discharge plasmas with a repetition rate of 1 Hz is used to produce a hard boron-containing coating for reversed field pinch (RFP) plasmas in the Madison Symmetric Torus. X-ray photoelectron spectroscopy with Ar ion beam etching for silicon coupons installed at the plasma boundary shows about 60% boron concentration in the deposited layer. Both profilometer and scanning electron microscope analyses of the silicon coupons imply a strong toroidally non-uniform deposition depending on the location of the o-carborane injection. The layer thickness ranges from 50 to 300 nm. Ellipsometry calibrated with the profilometer results yields a refractive index of 2.2-2.3 for the films. The high refractive index implies that the coating is hard and has a well-ordered morphology. A reduction in wall recycling has consistently been observed after all boronization sessions. Comparison of the X-ray spectra in standard RFP plasmas before and after boronization indicates a slight decrease in the effective ionic charge.

  1. Positive corona discharge in N_2 + CH_4 mixture at atmospheric pressure

    Science.gov (United States)

    Horvath, G.; Skalny, J. D.; Mason, N. J.; Zahoran, M.; Orszagh, J.

    2008-07-01

    Titan is considered as one of the few places in Solar system, where atmospheric and surface conditions could have produced organic molecules as precursors of higher hydrocarbons, nitriles or amino acids. Most of laboratory simulations of Titan's atmosphere were carried out at lower pressures presenting stratospheric conditions but there is poor knowledge about simulated reactions of Titan's troposphere. In our work an experimental investigation of products in positive coaxial corona discharge fed by mixture of N_2 and CH_4 with ratio of N_2:CH_4=98:2 in stationary regime has been made using UV spectroscopy. The measurements have been carried out at pressure of 1 bar and ambient temperature. The discharge reactor used for the treatment of the gas mixture consisted of a brass cylinder with diameter of 16 mm and length of 70 mm. A stainless steel and tungsten wires of diameter of 0.125 mm was centred inside the metal cylinder and was connected to the high voltage power supply. Coaxial corona discharge was generated by a Glassman high voltage power supply. The mixing ratio of methane and nitrogen was regulated by a MKS flow controllers. The reactor was placed in a Shimadzu VUV spectrometer for the in-situ measurements of absorbance of synthesized compounds. The measurements were focused on the UV analysis of time evolution of C_2H_2 and C_2H_4 concentrations and EMS study of deposited compounds on discharge electrodes (Figure 1). After a certain time a yellow- orange layer was formed on the active discharge electrode causing sparks and forming a dense rose-like spots on the covered electrode surface (Figure 2). Figure 1: EMS study of electrode surface. Figure 2: EMS picture of a treated electrode.

  2. Double discharges in unipolar-pulsed dielectric barrier discharge xenon excimer lamps

    Science.gov (United States)

    Liu, Shuhai; Neiger, Manfred

    2003-07-01

    Excitation of dielectric barrier discharge xenon excimer lamps by unipolar short square pulses is studied in this paper. Two discharges with different polarity are excited by each voltage pulse (double discharge phenomenon). The primary discharge occurs at the top or at the rising flank of the applied unipolar square pulse, which is directly energized by the external circuit. The secondary discharge with the reversed polarity occurs at the falling flank or shortly after the falling flank end (zero external voltage) depending on the pulse width, which is energized by the energy stored by memory charges deposited by the primary discharge. Fast-speed ICCD imaging shows the primary discharge has a conic discharge appearance with a channel broadening on the anode side. This channel broadening increases with increasing the pulse top level. Only the anode-side surface discharge is observed in the primary discharge. The surface discharge on the cathode side which is present in bipolar sine voltage excitation is not observed. On the contrary, the secondary discharge has only the cathode-side surface discharge. The surface discharge on the anode side is not observed. The secondary discharge is much more diffuse than the primary discharge. Time-resolved emission measurement of double discharges show the secondary discharge emits more VUV xenon excimer radiation but less infrared (IR) xenon atomic emission than the primary discharge. It was found that the IR xenon atomic emission from the secondary discharge can be reduced by shortening the pulse width. The energy efficiency of unipolar-pulsed xenon excimer lamps (the overall energy efficiency of double discharges) is much higher than that obtained under bipolar sine wave excitation. The output VUV spectrum under unipolar pulse excitation is found to be identical to that under sine wave excitation and independent of injected electric power.

  3. X-ray emission from a nanosecond-pulse discharge in an inhomogeneous electric field at atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Cheng; Shao Tao; Ren Chengyan; Zhang Dongdong [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China); Key Laboratory of Power Electronics and Electric Drive, Chinese Academy of Sciences, Beijing 100190 (China); Tarasenko, Victor; Kostyrya, Igor D. [Institute of High Current Electronics, Russian Academy of Science, Tomsk 634055 (Russian Federation); Ma Hao [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China); Yan Ping [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China); Key Laboratory of Power Electronics and Electric Drive, Chinese Academy of Sciences, Beijing 100190 (China); State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China)

    2012-12-15

    This paper describes experimental studies of the dependence of the X-ray intensity on the anode material in nanosecond high-voltage discharges. The discharges were generated by two nanosecond-pulse generators in atmospheric air with a highly inhomogeneous electric field by a tube-plate gap. The output pulse of the first generator (repetitive pulse generator) has a rise time of about 15 ns and a full width at half maximum of 30-40 ns. The output of the second generator (single pulse generator) has a rise time of about 0.3 ns and a full width at half maximum of 1 ns. The electrical characteristics and the X-ray emission of nanosecond-pulse discharge in atmospheric air are studied by the measurement of voltage-current waveforms, discharge images, X-ray count and dose. Our experimental results showed that the anode material rarely affects electrical characteristics, but it can significantly affect the X-ray density. Comparing the density of X-rays, it was shown that the highest x-rays density occurred in the diffuse discharge in repetitive pulse mode, then the spark discharge with a small air gap, and then the corona discharge with a large air gap, in which the X-ray density was the lowest. Therefore, it could be confirmed that the bremsstrahlung at the anode contributes to the X-ray emission from nanosecond-pulse discharges.

  4. Degradation of Organic Compounds by Active Species Sprayed in a Dielectric Barrier Corona Discharge System

    Institute of Scientific and Technical Information of China (English)

    LI Jie; SONG Ling; LIU Qiang; QU Guangzhou; LI Guofeng; WU Yan

    2009-01-01

    Investigation was made into the degradation of organic compounds by a dielectric barrier corona discharge (DBCD) system. The DBCD, consisting of a quartz tube, a concentric high voltage electrode and a net wrapped to the external wall (used as ground electrode), was introduced to generate active species which were sprayed into the organic solution through an aerator fixed on the bottom of the tube. The effect of four factors-the discharge voltage, gas flow rate, solution conductivity, and pH of wastewater, on the degradation efficiency of phenol was assessed. The obtained results demonstrated that this process was an effective method for phenol degradation. The degradation rate was enhanced with the increase in power supplied. The degradation efficiency in alkaline conditions was higher than those in acid and neutral conditions.The optimal gas flow rate for phenol degradation in the system was 1.6 L/min, while the solution conductivity had little effect on the degradation.

  5. Properties of water surface discharge at different pulse repetition rates

    Energy Technology Data Exchange (ETDEWEB)

    Ruma,; Yoshihara, K. [Graduate School of Science and Technology, Kumamoto University, Kumamoto 860-8555 (Japan); Hosseini, S. H. R., E-mail: hosseini@kumamoto-u.ac.jp; Sakugawa, T.; Akiyama, H. [Graduate School of Science and Technology, Kumamoto University, Kumamoto 860-8555 (Japan); Institute of Pulsed Power Science, Kumamoto University, Kumamoto 860-8555 (Japan); Akiyama, M. [Department of Electrical and Electronic Engineering, Kagoshima University, Kagoshima 890-0065 (Japan); Lukeš, P. [Institute of Plasma Physics, AS CR, Prague, Prague 18200 (Czech Republic)

    2014-09-28

    The properties of water surface discharge plasma for variety of pulse repetition rates are investigated. A magnetic pulse compression (MPC) pulsed power modulator able to deliver pulse repetition rates up to 1000 Hz, with 0.5 J per pulse energy output at 25 kV, was used as the pulsed power source. Positive pulse with a point-to-plane electrode configuration was used for the experiments. The concentration and production yield of hydrogen peroxide (H₂O₂) were quantitatively measured and orange II organic dye was treated, to evaluate the chemical properties of the discharge reactor. Experimental results show that the physical and chemical properties of water surface discharge are not influenced by pulse repetition rate, very different from those observed for under water discharge. The production yield of H₂O₂ and degradation rate per pulse of the dye did not significantly vary at different pulse repetition rates under a constant discharge mode on water surface. In addition, the solution temperature, pH, and conductivity for both water surface and underwater discharge reactors were measured to compare their plasma properties for different pulse repetition rates. The results confirm that surface discharge can be employed at high pulse repetition rates as a reliable and advantageous method for industrial and environmental decontamination applications.

  6. Simulation of a wire-cylinder-plate positive corona discharge in nitrogen gas at atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Alexandre A. [Institute for Plasmas and Nuclear Fusion and Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)

    2012-06-15

    In this work, we are going to perform a simulation of a wire-cylinder-plate positive corona discharge in nitrogen gas, and compare our results with already published experimental results in air for the same structure. We have chosen to simulate this innovative geometry because it has been established experimentally that it can generate a thrust per unit electrode length transmitted to the gas of up to 0.35 N/m and is also able to induce an ion wind top velocity in the range of 8-9 m/s in air. In our model, the used ion source is a small diameter wire, which generates a positive corona discharge in nitrogen gas directed to the ground electrode, after which the generated positive ions are further accelerated in the acceleration channel between the ground and cathode. By applying the fluid dynamic and electrostatic theories, all hydrodynamic and electrostatic forces that act on the considered geometries will be computed in an attempt to theoretically confirm the generated ion wind profile and also the thrust per unit electrode length. These results are important to establish the validity of this simulation tool for the future study and development of this effect for practical purposes.

  7. Simulation of a wire-cylinder-plate positive corona discharge in nitrogen gas at atmospheric pressure

    CERN Document Server

    Martins, Alexandre A

    2012-01-01

    In this work we are going to perform a simulation of a wire-cylinder-plate positive corona discharge in nitrogen gas, and compare our results with already published experimental results in air for the same structure. We have chosen to simulate this innovative geometry because it has been established experimentally that it can generate a thrust per unit electrode length transmitted to the gas of up to 0.35 N/m and is also able to induce an ion wind top velocity in the range of 8-9 m/s in air. In our model, the used ion source is a small diameter wire, which generates a positive corona discharge in nitrogen gas directed to the ground electrode, after which the generated positive ions are further accelerated in the acceleration channel between the ground and cathode. By applying the fluid dynamic and electrostatic theories all hydrodynamic and electrostatic forces that act on the considered geometries will be computed in an attempt to theoretically confirm the generated ion wind profile and also the thrust per u...

  8. Nanosecond Repetitively Pulsed Discharges in Air at Atmospheric Pressure -- Experiment and Theory of Regime Transitions

    Science.gov (United States)

    Pai, David; Lacoste, Deanna; Laux, Christophe

    2009-10-01

    In atmospheric pressure air preheated from 300 to 1000 K, the Nanosecond Repetitively Pulsed (NRP) method has been used to generate corona, glow, and spark discharges. Experiments have been performed to determine the parameter space (applied voltage, pulse repetition frequency, ambient gas temperature, and inter-electrode gap distance) of each discharge regime. Notably, there is a minimum gap distance for the existence of the glow regime that increases with decreasing gas temperature. A theory is developed to describe the Corona-to-Glow (C-G) and Glow-to-Spark (G-S) transitions for NRP discharges. The C-G transition is shown to depend on the Avalanche-to-Streamer Transition (AST) as well as the electric field strength in the positive column. The G-S transition is due to the thermal ionization instability. The minimum gap distance for the existence of the glow regime can be understood by considering that the applied voltage of the AST must be lower than that of the thermal ionization instability. This is a previously unknown criterion for generating glow discharges, as it does not correspond to the Paschen minimum or to the Meek-Raether criterion.

  9. Ozone production by a dc corona discharge in air contaminated by n-heptane

    Science.gov (United States)

    Pekárek, S.

    2008-01-01

    Beneficial purposes of ozone such as elimination of odours, harmful bacteria and mildew can be used for transportation of food, fruits and vegetables with the aim to extend their storage life. To date the main technique used for this purpose in the transportation of these commodities, e.g. by trucks, was cooling. Here a combination of cooling together with the supply of ozone into containers with these commodities is considered. For these purposes we studied the effect of air contamination by n-heptane (part of automotive fuels) and humidity on ozone production by a dc hollow needle to mesh corona discharge. We found that, for both polarities of the needle electrode, addition of n-heptane to air (a) decreases ozone production; (b) causes discharge poisoning to occur at lower current than for air; (c) does not substantially influence the current for which the ozone production reaches the maximum. Finally the maximum ozone production for the discharge in air occurs for the same current as the maximum ozone production for the discharge contaminated by n-heptane. We also found that humidity decreases ozone production from air contaminated by n-heptane irrespective of the polarity of the coronating needle electrode. This dependence is stronger for the discharge with the needle biased positively.

  10. Coupling of methane under pulse corona plasma (Ⅰ)——In the absence of oxygen

    Institute of Scientific and Technical Information of China (English)

    朱爱民; 宫为民; 张秀玲; 张报安

    2000-01-01

    At normal temperature and pressure, pulse corona plasma was used as a new method for the dehydrogenative coupling of methane in the absence of oxygen. The effects of voltage polarity and input energy on the dehydrogenative coupling of methane were investigated. The parameter "energy efficiency" was introduced to examine the coupling of the input energy and the dehydrogenative coupling of methane. The experimental results show that positive corona gives higher energy efficiency than negative corona. When the positive corona was chosen, C2. yield per pass was 31.6% and acetylene yield per pass was 30.1% with 44.6% methane conversion at an input energy density of 1788kJ/mol and a pulse repetition frequency of 66Hz. The function of input energy density towards methane conversion may be expressed as a formula of -ln(1-X) = k (P/F). In the range of input energy employed, C2 yield is proportional to input energy density, but energy efficiency drops off with increasing input energy density.

  11. 脉冲电晕结合Ca(OH)2吸收法脱硫脱硝%Removal of SO2 and NOx by Pulsed Corona Combined with in situ Ca(OH)2 Absorption

    Institute of Scientific and Technical Information of China (English)

    黄立维; 党永霞

    2011-01-01

    Removal of SO2 and NOx by pulsed corona combined with in situ alkali absorption was experimentally investigated. In the reactor, a plate-wire-plate combination is devised for generating pulsed corona and then alkaline absorbent slurries were introduced into the reactor by a continuous band conveying system to capture the gaseous reaction products. It was found that both SO2 and NO could be removed by corona combined with in situ alkali absorption. The removal of SO2 increased to 75% with the corona discharge, compared with 60% removal only with Ca(OH)2 absorption. About 40% removal of NO was reached by pulsed corona combined with in situ Ca(OH)2 absorption. It was found that SO2 and NO in the gas stream are oxidized to SO3 and NO2 by pulsed corona respectively, and then absorbed by the alkali in the reactor. The removals of SO2 as well as NO were higher with Ca(OH)2 as the absorbent, compared with using CaCO3 or ZnO.

  12. Accelerated formation of sodium depletion layer on soda lime glass surface by corona discharge treatment in hydrogen atmosphere

    Science.gov (United States)

    Kawaguchi, Keiga; Ikeda, Hiroshi; Sakai, Daisuke; Funatsu, Shiro; Uraji, Keiichiro; Yamamoto, Kiyoshi; Suzuki, Toshio; Harada, Kenji; Nishii, Junji

    2014-05-01

    Formation of a sodium depletion layer on a soda lime glass surface was accelerated efficiently using a corona discharge treatment in H2 atmosphere. One origin of such acceleration was the preferential generation of H+ with a larger mobility at an anode needle end with a lower applied voltage than that in air. The second origin was the applied voltage across the glass plate during the corona discharge treatment, which was estimated theoretically as 2.7 times higher than that in air. These two effects doubled the depletion layer thickness compared with that in air.

  13. Non-stationary corona around multi-point system in atmospheric electric field: I. Onset electric field and discharge current

    Science.gov (United States)

    Bazelyan, E. M.; Raizer, Yu. P.; Aleksandrov, N. L.

    2014-03-01

    The properties of a non-stationary glow corona maintained near the tips of a multi-point ground system in a time-varying thundercloud electric field have been studied numerically and analytically. Computer and analytical models were developed to simulate the corona discharge initiated from a system of identical vertical conductive electrodes distributed uniformly over a grounded plane surface. The simulation was based on a solution of the electrostatic equation for electric field and continuity equations for light and aerosol ions. The development of individual corona space charge layers from different points and the formation of a united plane layer were considered. The effect of system dimensions and that of the distance between electrodes on the external electric field corresponding to corona onset near the rod tips was investigated. The evolution in time of the corona current was calculated for systems with various numbers of coronating rods in time-varying atmospheric electric field. In the limit of infinite number of coronating rods, reasonable agreement was obtained between numerical calculations and analytical theory considering the effect of surrounding rods on the corona discharge from a given rod in a simplified integral way. Conditions were determined under which the corona properties of a multi-point system are similar to the properties of a plane surface emitting ions into the atmosphere. In this case, the corona current density is governed by the time derivative of the thundercloud electric field and is independent of the ion mobility and of the coronating system dimensions. The total corona space charge injected into the atmosphere per unit area by a given instant is controlled by the thundercloud electric field at this instant and depends on the geometrical parameters of the system only indirectly, through the corona onset atmospheric electric field. This simple model could be used to simulate a corona discharge during thunderstorms at the earth

  14. Room-temperature poling of PbTiO3/Pb(Zr,Ti)O3 sol-gel composite films by pulse discharge

    Science.gov (United States)

    Kouyama, Hikaru; Kibe, Taiga; Fujimoto, Shota; Namihira, Takao; Kobayashi, Makiko

    2016-07-01

    The PbTiO3/Pb(Zr,Ti)O3 (PT/PZT) sol-gel composite is a promising piezoelectric material because of its high piezoelectricity and temperature stability up to 360 °C. However, the poling of PT/PZT required high temperature owing to the high coercive field of PT, which made the poling of PT/PZT troublesome. In this research, conventional DC corona poling and pulse discharge at room temperature were attempted for PT/PZT samples. As a result, PT/PZT poled by pulse discharge generation at room temperature showed comparable ultrasonic responses to that poled by DC corona discharge generation at a high temperature. Therefore, room-temperature poling of PT/PZT was successfully carried out by pulse discharge, and poling time was markedly reduced from ˜15 min to 15 s.

  15. Experimental modeling of high-voltage corona discharge using design of experiments

    Institute of Scientific and Technical Information of China (English)

    Rezzouga M; Tilmatine A; Gouri R; Medics K; Dascalescu L

    2007-01-01

    Many studies,both experimental and numerical,were devoted to the electric current of corona discharge and some mathematical models were proposed to express it.As it depends on several parameters,it is difficult to find a theoretical or an experimental formula,which considers all the factors.So we opted for the methodology of experimental designs,also called Tagushi's methodology,which represents a powerful tool generally employed when the process has many factors to consider.The objective of this paper is to model current using this experimental methodology.The factors considered were geometrical factors (interelectrode interval,surface of the grounded plane electrode,curvature radius of the point electrode),climatic factors (temperature and relative humidity),and applied high voltage.Results of experiments made it possible to obtain mathematical models and to analyse the interactions between all factors.

  16. [Morphology determination of ionization region in multi-needle-to-plate negative corona discharge].

    Science.gov (United States)

    Su, Peng-Hao; Zhu, Yi-Min; Chen, Hai-Feng

    2007-11-01

    Based on the former work on the current-voltage characteristics of a multi-needle-to-plate negative corona discharge at atmospheric pressure, the present work uses the method of OES (optical emission spectrum) for measuring N2 emission spectrum, and the morphology determination of the ionization region has been investigated. According to the distribution of N2 second positive band's intensity I(SPB), the highest of all bands, the outline of the ionization region was drawn fairly accurately. The relationship between I(SPB) and discharge current I can be obtained through the volume integral of the I(SPB). The experimental results show that the size of the ionization region enhances with the rise of the applied voltage U, and the electron avalanche begins at about 1 mm off the tips of needle electrode and multiplies only in the range of several millimeters, indicating that, the range of the ionization region is at the magnitude of mm. The electron avalanche along the axis of the needle develops farther than that along the radial direction of needle, and the shape of the ionization region looks like a bullet. The integral of I(SPB) is second-order linear to I, with a very second order coefficient, meaning that the main excited substance is N2. Energetic electrons mainly exist in ionization region while ions are the main charged particles to form discharge current in the transfer region.

  17. CORONA DISCHARGE REACTOR FOR SELECTIVE OXIDATION OF ALCOHOLS AND HYDROCARBONS USING OZONATION AND PHOTOXIDATION OF OVER TIO2

    Science.gov (United States)

    We have developed a process that combines the use of surface corona for the production of ozone by passing air or oxygen through a high voltage electrical discharge and the emitted UV is being used to activate a photocatalyst. A thin film of nanostructured TiO2 with primary part...

  18. Self-pulsing in a low-current hollow cathode discharge: From Townsend to glow discharge

    Energy Technology Data Exchange (ETDEWEB)

    Qin, Yu [School of Physics, Beijing Institute of Technology, Beijing 100081 (China); School of Aerospace Engineering, Beijing Institute of Technology, Beijing 100081 (China); Xie, Kan, E-mail: xiekan@bit.edu.cn [School of Aerospace Engineering, Beijing Institute of Technology, Beijing 100081 (China); Zhang, Yu; Ouyang, Jiting [School of Physics, Beijing Institute of Technology, Beijing 100081 (China)

    2016-02-15

    We investigate the self-pulsing phenomenon of a low current cavity discharge in a cylindrical hollow cathode in pure argon. The waveforms of pulsed current and voltage are measured, and the time-averaged and time-resolved images of hollow cathode discharge are recorded by using high-speed intensified charge coupled device camera. The results show that the self-pulsing is a mode transition between low-current stage of Townsend discharge and high-current stage of glow discharge. During the self-pulsing, the current rising time relates to the dissipation of space charges, and the decay time relates to the reconstruction of the virtual anode by the accumulation of positive ions. Whether or not space charges can form and keep the virtual anode is responsible for the discharge mode and hence plays an important role in the self-pulsing phenomenon in low current hollow cathode discharge.

  19. All solid state pulsed power system for water discharge

    OpenAIRE

    Sakugawa, Takashi; Yamaguchi, Takahiro; Yamamoto, Kunihiro; Kiyan, Tsuyoshi; Namihira, Takao; Katsuki, Sunao; Akiyama, Hidenori; サクガワ, タカシ; ヤマグチ, タカヒロ; ヤマモト, クニヒロ; キヤン, ツヨシ; ナミヒラ, タカオ; カツキ, スナオ; アキヤマ, ヒデノリ; 佐久川, 貴志

    2005-01-01

    Pulsed power has been used to produce non-thermal plasmas in gases that generate a high electric field at the tip of streamer discharges, where high energy electrons, free radicals, and ozone are produced. Recently, all solid state pulsed power generators, which are operated with high repetition rate, long lifetime and high reliability, have been developed for industrial applications, such as high repetition rate pulsed gas lasers, high energy density plasma (EUV sources) and water discharges...

  20. Nanoparticle synthesis in pulsed low temperature discharges

    Energy Technology Data Exchange (ETDEWEB)

    Buss, R.J.

    1996-06-01

    Silicon nitride powders with an average size as low as 7 nm are synthesized in a pulsed radio frequency glow discharge. The as-synthesized silicon nitride powder from a silane/ammonia plasma has a high hydrogen content and is sensitive to oxidation in air. Post-plasma heating of the powder in a vacuum results in nitrogen loss, giving silicon-rich powder. In contrast, heat treatment at 800 C for 20 minutes in an ammonia atmosphere (200 Torr pressure) yields a hydrogen-free powder which is stable with respect to atmospheric oxidation. Several approaches to synthesizing silicon carbide nano-size powders are presented. Experiments using silane/hydrocarbon plasmas produce particles with a high hydrogen content as demonstrated by Fourier transform infrared analysis. The hydrogen is present as both CH and SiH functionality. These powders are extremely air-sensitive. A second approach uses a gas mixture of methyltrichlorosilane and hydrogen. The particles have a low hydrogen content and resist oxidation. Particle morphology of the silicon carbide is more spherical and there is less agglomeration than is observed in the silicon nitride powder.

  1. Laser-induced fluorescence from N2(+) ions generated by a corona discharge in ambient air.

    Science.gov (United States)

    Konthasinghe, Kumarasiri; Fitzmorris, Kristin; Peiris, Manoj; Hopkins, Adam J; Petrak, Benjamin; Killinger, Dennis K; Muller, Andreas

    2015-09-01

    In this work, we present the measurement of laser-induced fluorescence from N2(+) ions via the B(2)Σu(+)-X(2)Σg(+) band system in the near-ultraviolet. The ions were generated continuously by a plasma glow discharge in low pressure N2 and by a corona discharge in ambient air. The fluorescence decay time was found to rapidly decrease with increasing pressure leading to an extrapolated decay rate of ≍10(10) s(-1) at atmospheric pressure. In spite of this quenching, we were able to observe laser induced fluorescence in ambient air by means of a time-gated spectral measurement. In the process of comparing the emission signal with that of N2 spontaneous Raman scattering, ion concentrations in ambient air of order 10(8-)10(10) cm(-3) were determined. With moderate increases in laser power and collection efficiency, ion concentrations of less than 10(6) cm(-3) may be measurable, potentially enabling applications in atmospheric standoff detection of ionizing radiation from hazardous radioactive sources.

  2. Discharge processes of UV pre-ionized electric-discharge pulsed DF laser

    Science.gov (United States)

    Pan, Qikun; Xie, Jijiang; Shao, Chunlei; Wang, Chunrui; Shao, Mingzhen; Guo, Jin

    2016-03-01

    The discharge processes of ultraviolet (UV) pre-ionized electric-discharge pulsed DF laser operating with a SF6-D2 gas mixture are studied. A mathematical model based on continuity equation of electrons and Kirchhoff equations for discharge circuit is established to describe the discharge processes. Voltage and current waveforms of main discharge and voltage waveforms of pre-ionization are solved numerically utilizing the model. The calculations correctly display some physical processes, such as the delay time between pre-ionization and main discharge, breakdown of the main electrode and self-sustained volume discharge (SSVD). The results of theory are consistent with the experiments, which are performed in our non-chain pulsed DF laser. Then the delay inductance and peak capacitance are researched to analyze their influences on discharge processes, and the circuit parameters of DF laser are given which is useful to improve the discharge stability.

  3. Removal of a hydrogenated amorphous carbon film from the tip of a micropipette electrode using direct current corona discharge.

    Science.gov (United States)

    Kakuta, Naoto; Okuyama, Naoki; Yamada, Yukio

    2010-02-01

    Micropipette electrodes are fabricated by coating glass micropipettes first with metal and then with hydrogenated amorphous carbon (a-C:H) as an electrical insulator. Furthermore, at the tip of the micropipette electrode, the deposited a-C:H film needs to be removed to expose the metal-coated surface and hollow for the purposes of electrical measurement and injection. This paper describes a convenient and reliable method for removing the a-C:H film using direct current corona discharge in atmospheric air. The initial film removal occurred at an applied voltage of 1.5-2.0 kV, accompanied by an abrupt increase in the discharge current. The discharge current then became stable at a microampere level in the glow corona mode, and the removed area gradually extended.

  4. Formation of hydroxyl radicals and oxidation of toluene under corona discharge with water vapor as radical source

    Institute of Scientific and Technical Information of China (English)

    KANG Ying; WU ZuCheng

    2008-01-01

    With water vapor as the radical source, hydroxyl radicals (. OH) of strong oxidation property were formed by corona discharge, which was directly detected by electron spin resonance (ESR) technology. These . OH could efficiently degrade gaseous organic pollutants so as to reduce the toxicity of waste gas. The experimental result of toluene degradation under DC corona discharge showed that the deg-radation efficiency of toluene was nearly 100% in the medium of air containing saturated water vapor under the condition that interelectrode voltage was 20 kV, discharge current was 0.1 mA, reaction time was 120 s and initial concentration of toluene was 168 mg/m3, respeUvely. Seven intermediate products of toluene oxidation dissolving in liquid phase were also determined. The empolyment of environ-mental friendly . OH provides a new approach for the removal of gas pollutants.

  5. 2D simulation of active species and ozone production in a multi-tip DC air corona discharge

    Science.gov (United States)

    Meziane, M.; Eichwald, O.; Sarrette, J. P.; Ducasse, O.; Yousfi, M.

    2011-11-01

    The present paper shows for the first time in the literature a complete 2D simulation of the ozone production in a DC positive multi-tip to plane corona discharge reactor crossed by a dry air flow at atmospheric pressure. The simulation is undertaken until 1 ms and involves tens of successive discharge and post-discharge phases. The air flow is stressed by several monofilament corona discharges generated by a maximum of four anodic tips distributed along the reactor. The nonstationary hydrodynamics model for reactive gas mixture is solved using the commercial FLUENT software. During each discharge phase, thermal and vibrational energies as well as densities of radical and metastable excited species are locally injected as source terms in the gas medium surrounding each tip. The chosen chemical model involves 10 neutral species reacting following 24 reactions. The obtained results allow us to follow the cartography of the temperature and the ozone production inside the corona reactor as a function of the number of high voltage anodic tips.

  6. Matching a (sub)nanosecond pulse source to a corona plasma reactor

    Science.gov (United States)

    Huiskamp, T.; Beckers, F. J. C. M.; Hoeben, W. F. L. M.; van Heesch, E. J. M.; Pemen, A. J. M.

    2016-10-01

    In this paper we investigate the energy transfer from the pulses of a (sub)nanosecond pulse source to the plasma in a corona-plasma reactor. This energy transfer (or ‘matching’) should be as high as possible. We studied the effect of multiple parameters on matching, such as the reactor configuration, the pulse duration and amplitude and the energy density. The pulse reflection on the reactor interface has a significant influence on matching, and should be as low as possible to transfer the most energy into the reactor. We developed a multiple-wire inner conductor for the reactor which decreases the vacuum impedance of the reactor to decrease the pulse reflection on the reactor interface while maintaining a high electric field on the wire. The results were very encouraging and showed an energy transfer efficiency of over 90 percent. The matching results further show that there is only a small effect on the matching between different wire diameters. In addition, a long reactor and a long pulse result in the best matching due to the more intense plasma that is generated in these conditions. Finally, even without the multiple-wire reactor, we are able to achieve a very good matching (over 80 percent) between our pulse source and the reactor.

  7. Electro-hydrodynamics and kinetic modelling of polluted air flow activated by multi-tip-to-plane corona discharge

    Energy Technology Data Exchange (ETDEWEB)

    Meziane, M.; Eichwald, O.; Ducasse, O.; Marchal, F. [Universite de Toulouse, UPS, INPT, LAPLACE (Laboratoire Plasma et Conversion d' Energie), Toulouse Cedex 9 F-31062 (France); Sarrette, J. P.; Yousfi, M. [Universite de Toulouse, UPS, INPT, LAPLACE (Laboratoire Plasma et Conversion d' Energie), Toulouse Cedex 9 F-31062 (France); CNRS, LAPLACE, Toulouse F-31062 (France)

    2013-04-21

    The present paper is devoted to the 2D simulation of an Atmospheric Corona Discharge Reactor (ACDR) involving 10 pins powered by a DC high voltage and positioned 7 mm above a grounded metallic plane. The corona reactor is periodically crossed by thin mono filamentary streamers with a natural repetition frequency of some tens of kHz. The simulation involves the electro-dynamic, chemical kinetic, and neutral gas hydrodynamic phenomena that influence the kinetics of the chemical species transformation. Each discharge stage (including the primary and the secondary streamers development and the resulting thermal shock) lasts about one hundred nanoseconds while the post-discharge stages occurring between two successive discharge phases last one hundred microseconds. The ACDR is crossed by a lateral air flow including 400 ppm of NO. During the considered time scale of 10 ms, one hundred discharge/post-discharge cycles are simulated. The simulation involves the radical formation and thermal exchange between the discharges and the background gas. The results show how the successive discharges activate the flow gas and how the induced turbulence phenomena affect the redistribution of the thermal energy and the chemical kinetics inside the ACDR.

  8. Electro-hydrodynamics and kinetic modelling of polluted air flow activated by multi-tip-to-plane corona discharge

    Science.gov (United States)

    Meziane, M.; Eichwald, O.; Sarrette, J. P.; Ducasse, O.; Yousfi, M.; Marchal, F.

    2013-04-01

    The present paper is devoted to the 2D simulation of an Atmospheric Corona Discharge Reactor (ACDR) involving 10 pins powered by a DC high voltage and positioned 7 mm above a grounded metallic plane. The corona reactor is periodically crossed by thin mono filamentary streamers with a natural repetition frequency of some tens of kHz. The simulation involves the electro-dynamic, chemical kinetic, and neutral gas hydrodynamic phenomena that influence the kinetics of the chemical species transformation. Each discharge stage (including the primary and the secondary streamers development and the resulting thermal shock) lasts about one hundred nanoseconds while the post-discharge stages occurring between two successive discharge phases last one hundred microseconds. The ACDR is crossed by a lateral air flow including 400 ppm of NO. During the considered time scale of 10 ms, one hundred discharge/post-discharge cycles are simulated. The simulation involves the radical formation and thermal exchange between the discharges and the background gas. The results show how the successive discharges activate the flow gas and how the induced turbulence phenomena affect the redistribution of the thermal energy and the chemical kinetics inside the ACDR.

  9. Pulsed positive streamer discharges in air at high temperatures

    Science.gov (United States)

    Ono, Ryo; Kamakura, Taku

    2016-08-01

    Atmospheric-pressure air pulsed positive streamer discharges are generated in a 13 mm point-plane gap in the temperature range of 293 K-1136 K, and the effect of temperature on the streamer discharges is studied. When the temperature is increased, the product of applied voltage and temperature VT proportional to the reduced electric field can be used as a primary parameter that determines some discharge parameters regardless of temperature. For a given VT, the transferred charge per pulse, streamer diameter, product of discharge energy and temperature, and length of secondary streamer are almost constant regardless of T, whereas the streamer velocity decreases with increasing T and the decay rate of the discharge current is proportional to 1/T. The N2(C) emission intensity is approximately determined by the discharge energy independent of T. These results are useful to predict the streamer discharge and its reactive species production when the ambient temperature is increased.

  10. A morphological study of the changes in the ultrastructure of a bacterial biofilm disrupted by an ac corona discharge in air

    Science.gov (United States)

    Stepanova, Olga; Rybalchenko, Oksana; Astafiev, Alexander; Orlova, Olga; Kudryavtsev, Anatoly; Kapustina, Valentina

    2016-08-01

    The morphology of bacterial cells and biofilms subjected to a low frequency (˜105 Hz) ac (˜10-1 A) corona discharge was investigated using electron microscopy. A low-frequency ac corona discharge in air is shown to have a bactericidal and bacteriostatic effect on Escherichia coli M17 culture at both the cellular and population levels. Corona exposure inhibits the formation of a microbial community and results in the destruction of formed biofilms. This paper presents data on changes in the ultrastructure of cells and biofilms after corona treatment. Our results suggest that the E. coli M17 cells inside biofilms are affected with results similar to sub-lethal and lethal thermal exposure. Some of the biological aspects of colony and biofilm cells death are evaluated. Morphological changes in the ultrastructure of the biofilms under corona treatment are described. Our results indicate that the heating effect is the main factor responsible for the corona-induced inactivation of bacteria.

  11. Decomposition of mixed malodorants in a wire-plate pulse corona reactor.

    Science.gov (United States)

    Shi, Y; Ruan, J; Wang, X; Li, W; Tan, T

    2005-09-01

    Decomposition characteristics of two groups of representative mixed malodorants (1, ethanethiol + hydrogen sulfide; 2, ethanethiol + ammonia) in air were investigated employing a wire-plate pulse corona reactor. A new type of high-voltage pulse generator with a thyratron switch and a Blumlein pulse-forming network (BPFN) was used in our experiments. The experiments were conducted at a gas-flow rate of 13 m3/h. Important parameters, including peak voltage, chemical structures of malodorants, pulse frequency, and initial concentration, which influenced the removal efficiency, were investigated. The results showed that the mixed malodorants could be treated effectively by pulse corona. The removal efficiencies of 200 mg/m3 C2H5SH and 200 mg/m3 H2S for group 1 were 95.6% and 100%, respectively, which were almost equal to those of the two pollutants separately. The energy cost was about 65.1-81.4 J/L, which was 31.5-45.2% lower than for treating pollutants alone. The removal efficiencies of 105 mg/m3 C2HsSH and 40 mg/m3 NH3 for group 2 were 93.1% and almost 100%, and the energy cost was 65.1 J/L, 55.6% lower than that which was treated separately. In the case of two groups of mixed malodorants removal, NOx, 03, SO2, CO2, and CO were all observed. Moreover, some sulfur and white crystal ammonium nitrates were discovered adhering to the corona wires in the removal of groups 1 and 2, respectively. A dynamics model was developed to describe the relation of the removal efficiency with specific energy density and initial concentration. In the case of group 1 removal,the decomposition rate constants decreased as compared to the single treating. As for group 2 removal, the decomposition rate constants increased, especially for NH3. According to the results, the optimization design for the reactor and the matching of high pulse voltage source can be reckoned.

  12. Model of Pulsed Electrical Discharge Machining (EDM using RL Circuit

    Directory of Open Access Journals (Sweden)

    Ade Erawan Bin Minhat

    2014-10-01

    Full Text Available This article presents a model of pulsed Electrical Discharge Machining (EDM using RL circuit. There are several mathematical models have been successfully developed based on the initial, ignition and discharge phase of current and voltage gap. According to these models, the circuit schematic of transistor pulse power generator has been designed using electrical model in Matlab Simulink software to identify the profile of voltage and current during machining process. Then, the simulation results are compared with the experimental results.

  13. [Spectral diagnosis of hydroxyl radical in multiphase pulsed discharge system].

    Science.gov (United States)

    Wang, Hui-juan; Li, Jie; Quan, Xie; Wu, Yan; Li, Guo-feng

    2007-12-01

    A gas-liquid hybrid pulsed discharge system with a multi-needle-to-plate electrode geometry was used in the present study. A multiphase (gas-liquid-solid) pulsed discharge system was then formed by adding glasses beads immobilized with TiO2 photocatalyst into the discharge system. In the present paper, ultraviolet light produced during the pulsed discharge process was used as the lamp-house to induce the photocatalytic activity of the TiO2 photocatalyst. The synergistic effect of pulsed discharge and TiO2 photocatalysis was reviewed by the spectral diagnosis of hydroxyl radical ( *OH) in the pulsed discharge system. The obtained results showed that the emission spectrum of *OH could be observed at 306 nm (A2Sigma+-->X2II), 309 mn (A2Sigma+ (v' = 0) --> X2II (v" = 0)) and 313 nm (A2Sigma+ (v' = 1) --> X2II (v" = 1) transition). The relative emission intensity of *OH at 313 nm in the discharge system was the strongest among the three characteristic spectra. The relative emission intensity of *OH at 313 nm was stronger by adding TiO2 photocatalyst into the pulsed discharge system than that in the sole pulsed discharge system. In the case of experiments that changing the gas bubbling varieties and initial solution pH values, the results revealed that the relative emission intensity of *OH at 313 nm in the synergistic system was stronger when Ar was used as bubbling gas compared with that when air and oxygen were bubbled into the reaction system. Furthermore, the acidic solution system was favorable for producing more *OH, and therefore the corresponding emission intensity of *OH at 313 nm was stronger than that in the neutral and basic solution.

  14. Evaluation and Optimization of Electrode Configuration of Multi-Channel Corona Discharge Plasma for Dye-Containing Wastewater Treatment

    Science.gov (United States)

    Ren, Jingyu; Wang, Tiecheng; Qu, Guangzhou; Liang, Dongli; Hu, Shibin

    2015-12-01

    A discharge plasma reactor with a point-to-plane structure was widely studied experimentally in wastewater treatment. In order to improve the utilization efficiency of active species and the energy efficiency of this kind of discharge plasma reactor during wastewater treatment, the electrode configuration of the point-to-plane corona discharge reactor was studied by evaluating the effects of discharge spacing and adjacent point distance on discharge power and discharge energy density, and then dye-containing wastewater decoloration experiments were conducted on the basis of the optimum electrode configuration. The experimental results of the discharge characteristics showed that high discharge power and discharge energy density were achieved when the ratio of discharge spacing to adjacent point distance (d/s) was 0.5. Reactive Brilliant Blue (RBB) wastewater treatment experiments presented that the highest RBB decoloration efficiency was observed at d/s of 0.5, which was consistent with the result obtained in the discharge characteristics experiments. In addition, the biodegradability of RBB wastewater was enhanced greatly after discharge plasma treatment under the optimum electrode configuration. RBB degradation processes were analyzed by GC-MS and IC, and the possible mechanism for RBB decoloration was also discussed. supported by China's Postdoctoral Science Foundation (No. 2014M562460), the Initiative Funding Programs for Doctoral Research of Northwest A&F University (No. 2013BSJJ121), and National Natural Science Foundation of China (No. 21107085)

  15. Theoretical analysis of ozone generation by pulsed dielectric barrier discharge in oxygen

    Science.gov (United States)

    Wei, L. S.; Zhou, J. H.; Wang, Z. H.; Cen, K. F.

    2007-08-01

    The use of very short high-voltage pulses combined with a dielectric layer results in high-energy electrons that dissociate oxygen molecules into atoms, which are a prerequisite for the subsequent production of ozone by collisions with oxygen molecules and third particles. The production of ozone depends on both the electrical and the physical parameters. For ozone generation by pulsed dielectric barrier discharge in oxygen, a mathematical model, which describes the relation between ozone concentration and these parameters that are of importance in its design, is developed according to dimensional analysis theory. A formula considering the ozone destruction factor is derived for predicting the characteristics of the ozone generation, within the range of the corona inception voltage to the gap breakdown voltage. The trend showing the dependence of the concentration of ozone in oxygen on these parameters generally agrees with the experimental results, thus confirming the validity of the mathematical model.

  16. Pulse volume discharges in high pressure gases

    Science.gov (United States)

    Yamshchikov, V. A.

    2015-11-01

    New approach for suppression of plasma inhomogeneities and instabilities in the volume self-sustained discharge is offered. The physical model is offered and conditions of obtaining extremely homogeneous self-sustained discharge are defined (with full suppression of plasma inhomogeneity and instability). Results of calculations agree with experiments.

  17. Electric field in an AC dielectric barrier discharge overlapped with a nanosecond pulse discharge

    Science.gov (United States)

    Goldberg, Benjamin M.; Shkurenkov, Ivan; Adamovich, Igor V.; Lempert, Walter R.

    2016-08-01

    The effect of ns discharge pulses on the AC barrier discharge in hydrogen in plane-to-plane geometry is studied using time-resolved measurements of the electric field in the plasma. The AC discharge was operated at a pressure of 300 Torr at frequencies of 500 and 1750 Hz, with ns pulses generated when the AC voltage was near zero. The electric field vector is measured by ps four-wave mixing technique, which generates coherent IR signal proportional to the square of electric field. Absolute calibration was done using an electrostatic (sub-breakdown) field applied to the discharge electrodes, when no plasma was generated. The results are compared with one-dimensional kinetic modeling of the AC discharge and the nanosecond pulse discharge, predicting behavior of both individual micro-discharges and their cumulative effect on the electric field distribution in the electrode gap, using stochastic averaging based on the experimental micro-discharge temporal probability distribution during the AC period. Time evolution of the electric field in the AC discharge without ns pulses, controlled by a superposition of random micro-discharges, exhibits a nearly ‘flat top’ distribution with the maximum near breakdown threshold, reproduced quite well by kinetic modeling. Adding ns pulse discharges on top of the AC voltage waveform changes the AC discharge behavior in a dramatic way, inducing transition from random micro-discharges to a more regular, near-1D discharge. In this case, reproducible volumetric AC breakdown is produced at a well-defined moment after each ns pulse discharge. During the reproducible AC breakdown, the electric field in the plasma exhibits a sudden drop, which coincides in time with a well-defined current pulse. This trend is also predicted by the kinetic model. Analysis of kinetic modeling predictions shows that this effect is caused by large-volume ionization and neutralization of surface charges on the dielectrics by ns discharge pulses. The present

  18. Flow Separation Control on Airfoil With Pulsed Nanosecond Discharge Actuator

    NARCIS (Netherlands)

    Correale, G.; Popov, I.B.; Ratikin, A.E.; Starikovskii, A.Y.; Hulshoff, S.J.; Veldhuis, L.L.M.

    2011-01-01

    An experimental study of flow separation control with a nanosecond pulse plasma actuator was performed in wind-tunnel experiments. The discharge used had a pulse width of 12 ns and rising time of 3 ns with voltage up to 12 kV. Repetition frequency was adjustable up to 10 kHz. The first series of exp

  19. Numerical simulation of an oxygen-fed wire-to-cylinder negative corona discharge in the glow regime

    Science.gov (United States)

    Yanallah, K.; Pontiga, F.; Castellanos, A.

    2011-02-01

    Negative glow corona discharge in flowing oxygen has been numerically simulated for a wire-to-cylinder electrode geometry. The corona discharge is modelled using a fluid approximation. The radial and axial distributions of charged and neutral species are obtained by solving the corresponding continuity equations, which include the relevant plasma-chemical kinetics. Continuity equations are coupled with Poisson's equation and the energy conservation equation, since the reaction rate constants may depend on the electric field and temperature. The experimental values of the current-voltage characteristic are used as input data into the numerical calculations. The role played by different reactions and chemical species is analysed, and the effect of electrical and geometrical parameters on ozone generation is investigated. The reliability of the numerical model is verified by the reasonable agreement between the numerical predictions of ozone concentration and the experimental measurements.

  20. Generation of Porous Alumina Layers in a Polydimethylsiloxane/Hydrogen Peroxide Medium on Aluminum Substrate in Corona Discharges

    Directory of Open Access Journals (Sweden)

    A. Groza

    2014-01-01

    Full Text Available The porous alumina (Al2O3 layer obtained at the interface between polydimethylsiloxane/hydrogen peroxide medium and aluminum substrate under charged and neutral species injection produced in negative corona discharges in air at atmospheric pressure is analyzed by different methods in this paper. The scanning electron microscopy investigations showed the uniform distribution of the pores formed in the alumina layer and their columnar structures. Both energy dispersive X-ray spectroscopy (EDS and X-ray photoelectron spectroscopy (XPS measurements indicate that during the anodization process of the aluminum in the polydimethylsiloxane/hydrogen peroxide medium in corona discharge the incorporation of silicon in the structure of the alumina layer is possible.

  1. Numerical simulation of an oxygen-fed wire-to-cylinder negative corona discharge in the glow regime

    Energy Technology Data Exchange (ETDEWEB)

    Yanallah, K; Pontiga, F [Dpt. Fisica Aplicada II, Universidad de Sevilla (Spain); Castellanos, A [Dpt. Electronica y Electromagnetismo, Universidad de Sevilla (Spain)

    2011-02-09

    Negative glow corona discharge in flowing oxygen has been numerically simulated for a wire-to-cylinder electrode geometry. The corona discharge is modelled using a fluid approximation. The radial and axial distributions of charged and neutral species are obtained by solving the corresponding continuity equations, which include the relevant plasma-chemical kinetics. Continuity equations are coupled with Poisson's equation and the energy conservation equation, since the reaction rate constants may depend on the electric field and temperature. The experimental values of the current-voltage characteristic are used as input data into the numerical calculations. The role played by different reactions and chemical species is analysed, and the effect of electrical and geometrical parameters on ozone generation is investigated. The reliability of the numerical model is verified by the reasonable agreement between the numerical predictions of ozone concentration and the experimental measurements.

  2. Abatement and degradation pathways of toluene in indoor air by positive corona discharge.

    Science.gov (United States)

    Van Durme, J; Dewulf, J; Sysmans, W; Leys, C; Van Langenhove, H

    2007-08-01

    Indoor air concentrations of volatile organic compounds often exceed outdoor levels by a factor of 5. There is much interest in developing new technologies in order to improve indoor air quality. In this work non-thermal plasma (DC positive corona discharge) is explored as an innovative technology for indoor air purification. An inlet gas stream of 10 l min(-1) containing 0.50+/-0.02 ppm toluene was treated by the plasma reactor in atmospheric conditions. Toluene removal proved to be achievable with a characteristic energy density epsilon(0) of 50 J l(-1). Removal efficiencies were higher for 26% relative humidity (epsilon(0)=35 J l(-1)), compared with those at increased humidities (50% relative humidity, epsilon(0)=49 J l(-1)). Reaction products such as formic acid, benzaldehyde, benzyl alcohol, 3-methyl-4-nitrophenol, 4-methyl-2-nitrophenol, 4-methyl-2-propyl furan, 5-methyl-2-nitrophenol, 4-nitrophenol, 2-methyl-4,6-dinitrophenol are identified by means of mass spectrometry. Based on these by-products a toluene degradation mechanism is proposed.

  3. Analysis of explosives using corona discharge ionization combined with ion mobility spectrometry-mass spectrometry.

    Science.gov (United States)

    Lee, Jihyeon; Park, Sehwan; Cho, Soo Gyeong; Goh, Eun Mee; Lee, Sungman; Koh, Sung-Suk; Kim, Jeongkwon

    2014-03-01

    Corona discharge ionization combined with ion mobility spectrometry-mass spectrometry (IMS-MS) was utilized to investigate five common explosives: cyclonite (RDX), trinitrotoluene (TNT), pentaerythritol tetranitrate (PETN), cyclotetramethylenetetranitramine (HMX), and 2,4-dinitrotoluene (DNT). The MS scan and the selected ion IMS analyses confirmed the identities of the existing ion species and their drift times. The ions observed were RDX·NO3(-), TNT(-), PETN·NO3(-), HMX·NO3(-), and DNT(-), with average drift times of 6.93 ms, 10.20 ms, 9.15 ms, 12.24 ms, 11.30 ms, and 8.89 ms, respectively. The reduced ion mobility values, determined from a standard curve calculated by linear regression of (normalized drift times)(-1) versus literature K0 values, were 2.09, 1.38, 1.55, 1.15, 1.25, and 1.60 cm(2) V(-1) s(-1), respectively. The detection limits were found to be 0.1 ng for RDX, 10 ng for TNT, 0.5 ng for PETN, 5.0 ng for HMX, and 10 ng for DNT. Simplified chromatograms were observed when nitrogen, as opposed to air, was used as the drift gas, but the detection limits were approximately 10 times worse (i.e., less sensitivity of detection). © 2013 Elsevier B.V. All rights reserved.

  4. Biodiesel production using fatty acids from food industry waste using corona discharge plasma technology.

    Science.gov (United States)

    Cubas, A L V; Machado, M M; Pinto, C R S C; Moecke, E H S; Dutra, A R A

    2016-01-01

    This article aims to describe an alternative and innovative methodology to transform waste, frying oil in a potential energy source, the biodiesel. The biodiesel was produced from fatty acids, using a waste product of the food industry as the raw material. The methodology to be described is the corona discharge plasma technology, which offers advantages such as acceleration of the esterification reaction, easy separation of the biodiesel and the elimination of waste generation. The best conditions were found to be an oil/methanol molar ratio of 6:1, ambient temperature (25 °C) and reaction time of 110 min and 30 mL of sample. The acid value indicates the content of free fatty acids in the biodiesel and the value obtained in this study was 0.43 mg KOH/g. Peaks corresponding to octadecadienoic acid methyl ester, octadecanoic acid methyl ester and octadecenoic acid methyl ester, from the biodiesel composition, were identified using GC-MS. A major advantage of this process is that the methyl ester can be obtained in the absence of chemical catalysts and without the formation of the co-product (glycerin). Copyright © 2015 Elsevier Ltd. All rights reserved.

  5. Infrared spectral investigation of the linseed oil polymerization in a corona discharge in air at atmospheric pressure

    Science.gov (United States)

    Groza, A.; Surmeian, A.; Ganciu, M.; Popescu, I. I.

    2004-12-01

    In this paper we have demonstrated that the negative and positive corona discharge in air at atmospheric pressure is a convenient physical method for the initiation of the high-reaction-rate polymerization process of the linseed oil. The different stages of the polymerization process were investigated by infrared (IR) spectroscopy and the formation of the linseed oil polymer was evaluated by the presence of the C-O-C bands.

  6. Study on Detection of Negative Corona Discharge Generated in Rod-Plane Air Gap by Using External Electrode Method

    Institute of Scientific and Technical Information of China (English)

    N.ICHIKAWA

    2007-01-01

    A detective method of a negative corona discharge by means of an external electrode is presented.The relationship between an area of the external electrode and a detected voltage waveform is examined experimentally.This experimental study is carried out with the use of a rod-plane air gap.The results obtained will be applicable to problems associated with silos,ducts,and high-voltage equipment.

  7. Pulsed discharge plasmas in supercritical carbon dioxide

    OpenAIRE

    Kiyan, Tsuyoshi; Uemura, A.; Tanaka, K.; Zhang, C. H.; Namihira, Takao; Sakugawa, Takashi; Katsuki, Sunao; Akiyama, Hidenori; Roy, B.C.; Sasaki, M.; Goto, M.; キヤン, ツヨシ; ナミヒラ, タカオ; サクガワ, タカシ; カツキ, スナオ

    2005-01-01

    In recent years, several studies about electrical discharge plasma in supercritical carbon dioxide (CO2) have been carried out. One of the unique characteristics of supercritical fluid is a large density fluctuation near the critical point that can result in marked dramatic changes of thermal conductivity. Therefore, the electrical discharge plasma produced in supercritical fluid has unique features and reactions unlike those of normal plasma produced in gas phase. In our experiments, two typ...

  8. Improving thrust by pulse-induced breakdown enhancement in AC surface dielectric barrier discharge actuators for airflow control

    Science.gov (United States)

    Yan, Huijie; Yang, Liang; Qi, Xiaohua; Ren, Chunsheng

    2016-07-01

    The characteristics of a plate-to-plate AC surface dielectric barrier discharge (SDBD) actuator using the pulse-induced breakdown enhancing method are experimentally investigated. The encapsulated electrode is supplied with a sine high AC voltage, while the exposed electrode is feed by a synchronized pulse voltage. Based on the thrust force and power consumption measurements, a parametric study was performed using a positive pulse applied at the trough phase of the AC cycles in which the thrust force was observed to increase by about 100% to 300% and the efficiency up to about 100% compared with the AC-only supply conditions for different AC voltages within the tested range. The pulse-induced breakdown effect was analyzed from the electrical and light emission waveforms to reveal the underlying mechanism. The surface potential due to the charge deposition effect was also measured using a specially designed corona-like discharge potential probe. It is shown that the pulse-induced breakdown was able to cause a temporarily intensified local electric field to enhance the glow-like discharge and meanwhile increase the time-average surface potential in the region further downstream. The improvement in the force by the enhancement in the pulse-induced breakdown was mainly due to enhancements in the glow-like discharge and the surface potential increment, with the latter being more important when the AC voltage is higher.

  9. Dynamic corona characteristics of water droplets on charged conductor surface

    Science.gov (United States)

    Xu, Pengfei; Zhang, Bo; Wang, Zezhong; Chen, Shuiming; He, Jinliang

    2017-03-01

    The formation of the Taylor cone of a water droplet on the surface of the conductor in a line-ground electrode system is captured using a high-speed camera, while the corona current is synchronously measured using a current measurement system. Repeated Taylor cone deformation is observed, yielding regular groupings of corona current pulses. The underlying mechanism of this deformation is studied and the correlation between corona discharge characteristics and cone deformation is investigated. Depending on the applied voltage and rate of water supply, the Taylor cone may be stable or unstable and has a significant influence on the characteristics of the corona currents. If the rate of water supply is large enough, the Taylor cone tends to be unstable and generates corona-current pulses of numerous induced current pulses with low amplitudes. In consequence, this difference suggests that large rainfall results in simultaneously lower radio interference and higher corona loss.

  10. Statistical characteristic in time-domain of direct current corona-generated audible noise from conductor in corona cage

    Science.gov (United States)

    Li, Xuebao; Cui, Xiang; Lu, Tiebing; Ma, Wenzuo; Bian, Xingming; Wang, Donglai; Hiziroglu, Huseyin

    2016-03-01

    The corona-generated audible noise (AN) has become one of decisive factors in the design of high voltage direct current (HVDC) transmission lines. The AN from transmission lines can be attributed to sound pressure pulses which are generated by the multiple corona sources formed on the conductor, i.e., transmission lines. In this paper, a detailed time-domain characteristics of the sound pressure pulses, which are generated by the DC corona discharges formed over the surfaces of a stranded conductors, are investigated systematically in a laboratory settings using a corona cage structure. The amplitude of sound pressure pulse and its time intervals are extracted by observing a direct correlation between corona current pulses and corona-generated sound pressure pulses. Based on the statistical characteristics, a stochastic model is presented for simulating the sound pressure pulses due to DC corona discharges occurring on conductors. The proposed stochastic model is validated by comparing the calculated and measured A-weighted sound pressure level (SPL). The proposed model is then used to analyze the influence of the pulse amplitudes and pulse rate on the SPL. Furthermore, a mathematical relationship is found between the SPL and conductor diameter, electric field, and radial distance.

  11. Statistical characteristic in time-domain of direct current corona-generated audible noise from conductor in corona cage

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xuebao, E-mail: lxb08357x@ncepu.edu.cn; Cui, Xiang, E-mail: x.cui@ncepu.edu.cn; Ma, Wenzuo; Bian, Xingming; Wang, Donglai [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China Electric Power University, Beijing 102206 (China); Lu, Tiebing, E-mail: tiebinglu@ncepu.edu.cn [Beijing Key Laboratory of High Voltage and EMC, North China Electric Power University, Beijing 102206 (China); Hiziroglu, Huseyin [Department of Electrical and Computer Engineering, Kettering University, Flint, Michigan 48504 (United States)

    2016-03-15

    The corona-generated audible noise (AN) has become one of decisive factors in the design of high voltage direct current (HVDC) transmission lines. The AN from transmission lines can be attributed to sound pressure pulses which are generated by the multiple corona sources formed on the conductor, i.e., transmission lines. In this paper, a detailed time-domain characteristics of the sound pressure pulses, which are generated by the DC corona discharges formed over the surfaces of a stranded conductors, are investigated systematically in a laboratory settings using a corona cage structure. The amplitude of sound pressure pulse and its time intervals are extracted by observing a direct correlation between corona current pulses and corona-generated sound pressure pulses. Based on the statistical characteristics, a stochastic model is presented for simulating the sound pressure pulses due to DC corona discharges occurring on conductors. The proposed stochastic model is validated by comparing the calculated and measured A-weighted sound pressure level (SPL). The proposed model is then used to analyze the influence of the pulse amplitudes and pulse rate on the SPL. Furthermore, a mathematical relationship is found between the SPL and conductor diameter, electric field, and radial distance.

  12. Partial discharge pulse shape recognition using an inductive loop sensor

    Science.gov (United States)

    Martínez-Tarifa, J. M.; Robles, G.; Rojas-Moreno, M. V.; Sanz-Feito, J.

    2010-10-01

    Partial discharges (PD) are a clear ageing agent on insulating materials used in high-voltage electrical machines and cables. For this reason, there is increasing interest in measuring this phenomenon in an effort to forecast unexpected failures in electrical equipment. In order to focus on harmful discharges, PD pulse shape analysis is being used as an insulation defect identification technique. In this paper, a simple, inexpensive and high-frequency inductive loop sensor will be used to detect and acquire PD pulses. Several measurements will be made on some controlled test cell geometries in order to characterize PD pulse shapes for different discharge sources. The sensor identification capability has been checked in an insulation system where two simultaneous PD sources were active.

  13. Evaluating the generation efficiency of hydrogen peroxide in water by pulsed discharge over water surface and underwater bubbling pulsed discharge

    Science.gov (United States)

    Shang, Kefeng; Li, Jie; Wang, Xiaojing; Yao, Dan; Lu, Na; Jiang, Nan; Wu, Yan

    2016-01-01

    Pulsed electric discharge over water surface/in water has been used to generate reactive species for decomposing the organic compounds in water, and hydrogen peroxide (H2O2) is one of the strong reactive species which can be decomposed into another stronger oxidative species, hydroxyl radical. The production efficacy of H2O2 by a gas phase pulsed discharge over water surface and an underwater bubbling pulsed discharge was evaluated through diagnosis of H2O2 by a chemical probe method. The experimental results show that the yield and the production rate of H2O2 increased with the input energy regardless of the electric discharge patterns, and the underwater bubbling pulsed discharge was more advantageous for H2O2 production considering both the yield and the production rate of H2O2. Results also indicate that the electric discharge patterns also influenced the water solution properties including the conductivity, the pH value and the water temperature.

  14. Pulsed high voltage electric discharge disinfection of microbially contaminated liquids.

    Science.gov (United States)

    Anpilov, A M; Barkhudarov, E M; Christofi, N; Kop'ev, V A; Kossyi, I A; Taktakishvili, M I; Zadiraka, Y

    2002-01-01

    To examine the use of a novel multielectrode slipping surface discharge (SSD) treatment system, capable of pulsed plasma discharge directly in water, in killing micro-organisms. Potable water containing Escherichia coli and somatic coliphages was treated with pulsed electric discharges generated by the SSD. The SSD system was highly efficient in the microbial disinfection of water with a low energy utilization (eta approximately 10-4 kW h l-1). The SSD treatment was effective in the destruction of E. coli and its coliphages through the generation of u.v. radiation, ozone and free radicals. The non-thermal treatment method can be used for the eradication of micro-organisms in a range of contaminated liquids, including milk, negating the use of pasteurization. The method utilizes multipoint electric discharges capable of treating large volumes of liquid under static and flowing regimes.

  15. Improvement on Diamond Nucleation Treated by Pulsed Arc Discharge Plasma

    Institute of Scientific and Technical Information of China (English)

    马志斌; 万军; 汪建华; 张文文

    2004-01-01

    A technique of improvement on diamond nucleation based on pulsed arc discharge plasma at atmospheric pressure was developed. The pulsed arc discharge was induced respectively by nitrogen, argon and methanol gas. After the arc plasma pretreatment, a nucleation density higher than 1010 cm-2 may be obtained subsequently in chemical vapor deposition (CVD) on a mirror-polished silicon substrate without any other mechanical treatment. The effects of the arc discharge plasma on the diamond nucleation were investigated by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), infrared spectroscopy (IR) and Raman spectroscopy. The enhancement of nucleation is postulated to be a result of the formation of carbonlike phase materials or nitrogenation on the substrate surface without surface defect produced by arc discharge.

  16. Research on corona discharge based on AFM probe%基于AFM探针的电晕放电研究

    Institute of Scientific and Technical Information of China (English)

    赵贵; 孔德义; Juergen Brugger; 陈池来; 程玉鹏; 李庄

    2011-01-01

    针对扫描探针显微镜与质谱联用系统中的采样方式,提出了利用原子力显微镜(AFM)探针进行电晕放电解吸附的采样方案.运用ANSYS软件对AFM导电探针进行了有限元仿真,电场分析表明间距100 μm加1 kV高压时的AFM探针周围场强在0.32 ~62.4 V/μm间,验证了利用其产生电晕放电的可行性;通过实验观察了电晕放电现象及其规律,测得了AFM探针加高压时的伏安特性曲线,为下一步利用AFM探针产生电晕放电进行非触式采样奠定了良好的基础.%An atomic force microscopy ( AFM) probe based corona discharge sampling device for desorption ionization in scanning probe microscope mass spectrometer (SPM-MS) is put forward. Through finite element analysis, research is done on the mechanical and electrical character of the AFM probe tip. Electrical analysis shows that the field intensity around the AFM probe could achieve 0.32 -62.4 V/μun when the gap distance is 100 fun and the applied voltage is 1 kV, validating the feasibility and usability of the sampling device. The relationship between discharge current I and applied voltage V is studied through corona discharge experiment. These works lay a foundation for developing the corona discharge for non-contact sampling based on AFM probe.

  17. The contamination effects and other environmental agents in relation to the power losses by corona discharges; Efecto de la contaminacion y otros agentes ambientales sobre las perdidas por efecto corona

    Energy Technology Data Exchange (ETDEWEB)

    Mombello, Henrique E.; Ratta, Giuseppe; Suarez, Hector D.; Torres, Federico [Universidad Nacional de San Juan, San Juan (Argentina). Inst. de Energia Electrica]. E-mail: mombello@iee.unsj.edu.ar

    2001-07-01

    This document describes the accomplished investigations in laboratory, involving the effects from several contaminator and environment agents on the levels of corona discharges in power transmission lines in relation to dry climate. It is known that a severe contamination in dry climate produces significant power loss increases due to corona discharges. There is not in the available literature any investigation related to the dry climate just with snow and rainy climate, naturally these two conditions are very different. The researches for dry climate are very important to many regions in South America. The researches results have taken the researchers to empiric equation formulations in order to preview the levels of power losses caused by corona discharges.

  18. Pulsed electrical discharges for medicine and biology techniques, processes, applications

    CERN Document Server

    Kolikov, Victor

    2015-01-01

    This book presents the application of pulsed electrical discharges in water and water dispersions of metal nanoparticles in medicine (surgery, dentistry, and oncology), biology, and ecology. The intensive electrical and shock waves represent a novel technique to destroy viruses and this way to  prepare anti-virus vaccines. The method of pulsed electrical discharges in water allows to decontaminate water from almost all known bacteria and spores of fungi being present in human beings. The nanoparticles used are not genotoxic and mutagenic. This book is useful for researchers and graduate students.

  19. Simulating the inception of pulsed discharges near positive electrodes

    Science.gov (United States)

    Teunissen, Jannis; Ebert, Ute

    2013-09-01

    With 3D particle simulations we study the inception of pulsed discharges near positive electrodes. In different geometries, we first determine the breakdown voltage. Then we study the probability of inception for a fast voltage pulse. This probability mostly depends on the availability of seed electrons to generate the initial electron avalanches. These results are compared with experimental observations. Then we investigate how the shape of a starting discharge affects its further development. In particular, we discuss the formation of so-called ``inception clouds.'' JT was supported by STW-project 10755.

  20. Early Stage of Pulsed Discharge in Water

    Institute of Scientific and Technical Information of China (English)

    卢新培; 潘垣; 刘克富; 刘明海; 张寒虹

    2001-01-01

    The bubble radius at the early stage of discharge in water is investigated using high-speed photography. Some simulation results on the bubble radius are presented, which are in agreement with the experimental results, with a maximum difference of about 10%. The reasons why the peak pressure of the first shock wave is only related to the energy released in the bubble during the first half period are addressed. The energy released in the bubble after the first half period increases the bubble pulsation period, but it produces no more than 10% under the peak pressure of the second shock wave.

  1. Observation of enhanced ozone in an electrically active storm over Socorro, NM: Implications for ozone production from corona discharges

    Science.gov (United States)

    Minschwaner, K.; Kalnajs, L. E.; Dubey, M. K.; Avallone, L. M.; Sawaengphokai, P. C.; Edens, H. E.; Winn, W. P.

    2008-09-01

    Enhancements in ozone were observed between about 3 and 10 km altitude within an electrically active storm in central New Mexico. Measurements from satellite sensors and ground-based radar show cloud top pressures between 300 and 150 mb in the vicinity of an ozonesonde launched from Socorro, NM, and heavy precipitation with radar reflectivities exceeding 50 dBZ. Data from a lightning mapping array and a surface electric field mill show a large amount of electrical activity within this thunderstorm. The observed ozone enhancements are large (50% above the mean) and could have resulted from a number of possible processes, including the advection of polluted air from the urban environments of El Paso and Juarez, photochemical production by lightning-generated NOx from aged thunderstorm outflow, downward mixing of stratospheric air, or local production from within the thunderstorm. We find that a large fraction of the ozone enhancement is consistent with local production from corona discharges, either from cloud particles or by corona associated with lightning. The implied global source of ozone from thunderstorm corona discharge is estimated to be 110 Tg O3 a-1 with a range between 40 and 180 Tg O3 a-1. This value is about 21% as large as the estimated ozone production rate from lightning NOx, and about 3% as large as the total chemical production rate of tropospheric ozone. Thus while the estimated corona-induced production of ozone may be significant on local scales, it is unlikely to be as important to the global ozone budget as other sources.

  2. Solid State Capacitor Discharge Pulsed Power Supply Design for Railguns

    Science.gov (United States)

    2007-03-01

    CAPACITOR DISCHARGE PULSED POWER SUPPLY DESIGN FOR RAILGUNS by Jesse H. Black March 2007 Thesis Advisor: Alexander L. Julian Co-Advisor...switched power supply capable of providing 50 kJ from a high voltage capacitor to a railgun . The efficiency with which energy is transferred from a...also produce a smaller electromagnetic pulse. Voltage limitations on the thyristors require two in series acting as a single switch. Railgun

  3. Power Consideration for Pulsed Discharges in Potassium Seeded Argon

    Institute of Scientific and Technical Information of China (English)

    XIA Sheng-Guo; HE Jun-Jia; LIU Ke-Fu

    2007-01-01

    Minimization of energy consumed in plasma generation is critical for applications, in which a large volume of plasmas is needed. We suggest that a high electron density atmospheric pressure plasmas can be generated by pulsed discharges in potassium seeded argon at an elevated temperature with a very small power input. The ionization efficiency and power budget of pulsed discharges in such plasmas are analytically studied. The results show that ionization efficiency of argon, especially at small reduced electric field E/N (the ratio of the electric field to the gas number density), is improved effectively in the presence of small amount of potassium additives. Power input of pulsed discharge to sustain a prescribed average level of ionization in potassium seeded argon is three orders of magnitude lower than that in pure argon. Further, unlike in pure argon, it is found that very short high-voltage pulses with very high repetition rates are unnecessary in potassium seeded argon. A pulse with 100ns of pulse duration, 5kHz of repetition rate, and 2Td (1 Td = 1 ×10-21 Vm2) of E/N is enough to sustain an electron density of 10l9m-3 in 1 atm 1500 K Ar+0.1% K mixture, with a very small power input of about 0.08 × 104 W/m3.

  4. Simulation of pulsed dielectric barrier discharge xenon excimer lamp

    Science.gov (United States)

    Bogdanov, E. A.; Kudryavtsev, A. A.; Arslanbekov, R. R.; Kolobov, V. I.

    2004-11-01

    Recently, it has been shown that the efficiency of excimer lamps can be drastically increased in a pulsed regime. A one-dimensional simulation of pulsed excimer lamps has been performed by Carman and Mildren (2003 J. Phys. D: Appl. Phys. 36 19) (C&M). However, some computational results of the work of C&M are questionable and need to be revisited. In this paper, a dielectric barrier discharge (DBD) in xenon has been simulated for operating conditions similar to those of C&M to better understand plasma dynamics in a pulsed regime. Our simulation results differ considerably from the computational results of C&M. Although these differences do not affect profoundly the plasma macro parameters measured in the C&M experiments, they offer a better understanding of plasma dynamics in pulsed DBDs and form a solid foundation for computational optimization of excimer lamps. It was found that the dynamics of breakdown and the current pulse depend significantly on the initial densities of species after a previous pulse, and so it is important to accurately simulate the plasma evolution in both the afterglow and active stages. It seems possible to modify the power deposition in the plasma by varying external discharge parameters such as the amplitude and the rise time of the applied voltage, and to modify the plasma composition by changing the pulse repetition rate and plasma decay in the afterglow stage.

  5. Simulation of pulsed dielectric barrier discharge xenon excimer lamp

    Energy Technology Data Exchange (ETDEWEB)

    Bogdanov, E A [St Petersburg State University, St Petersburg (Russian Federation); Kudryavtsev, A A [St Petersburg State University, St Petersburg (Russian Federation); Arslanbekov, R R [CFD Research Corporation, Huntsville (United States); Kolobov, V I [CFD Research Corporation, Huntsville (United States)

    2004-11-07

    Recently, it has been shown that the efficiency of excimer lamps can be drastically increased in a pulsed regime. A one-dimensional simulation of pulsed excimer lamps has been performed by Carman and Mildren (2003 J. Phys. D: Appl. Phys. 36 19) (C and M). However, some computational results of the work of C and M are questionable and need to be revisited. In this paper, a dielectric barrier discharge (DBD) in xenon has been simulated for operating conditions similar to those of C and M to better understand plasma dynamics in a pulsed regime. Our simulation results differ considerably from the computational results of C and M. Although these differences do not affect profoundly the plasma macro parameters measured in the C and M experiments, they offer a better understanding of plasma dynamics in pulsed DBDs and form a solid foundation for computational optimization of excimer lamps. It was found that the dynamics of breakdown and the current pulse depend significantly on the initial densities of species after a previous pulse, and so it is important to accurately simulate the plasma evolution in both the afterglow and active stages. It seems possible to modify the power deposition in the plasma by varying external discharge parameters such as the amplitude and the rise time of the applied voltage, and to modify the plasma composition by changing the pulse repetition rate and plasma decay in the afterglow stage.

  6. Laser Thomson scattering in a pulsed atmospheric arc discharge

    Science.gov (United States)

    Sommers, Bradley; Adams, Steven

    2015-09-01

    Laser scattering measurements, including Rayleigh, Raman, and Thomson scattering have been performed on an atmospheric pulsed arc discharge. Such laser scattering techniques offer a non-invasive diagnostic to measure gas temperature, electron temperature, and electron density in atmospheric plasma sources, particularly those with feature sizes approaching 1 mm. The pulsed discharge is ignited in a pin to pin electrode geometry using a 6 kV pulse with 10 ns duration. The electrodes are housed in a glass vacuum chamber filled with argon gas. The laser signal is produced by a Nd:Yag laser supply, repetitively pulsed at 10 Hz and frequency quadrupled to operate at 266 nm. The scattered laser signal is imaged onto a triple grating spectrometer, which is used to suppress the Rayleigh scatter signal in order to measure the low amplitude Thomson and Raman signals. Preliminary results include measurements of electron temperature and electron density in the plasma column taken during the evolution of the discharge. The laser system is also used to measure the Rayleigh scattering signal, which provides space and time resolved measurements of gas temperature in the arc discharge.

  7. Inactivation of Staphylococcus aureus in water by pulsed spark discharge.

    Science.gov (United States)

    Zheng, Jiansheng

    2017-09-04

    A pulsed spark plasma discharge system was developed and tested as an energy efficient water sterilization method. A 5 log10 reduction on Staphylococcus aureus concentration of 10(8) CFU/ml was obtained. Complete inactivation was achieved for concentration of 10(6) CFU/ml. Of the various factors generated by an underwater spark discharge, ultraviolet radiation plays a major role. The inactivation was completely suppressed by the addition of 30 mg/L of a soluble sunscreen, Benzophenone-9. Results obtained using the pulsed spark plasma discharge showed that this system has several advantages, such as high energy efficiency, absence of harmful by-products and portability, over the conventional sterilization methods.

  8. Spectroscopic Investigation of a Repetitively-Pulsed Nanosecond Discharge

    Science.gov (United States)

    Yee, Benjamin T.

    This work reports on an investigation of a repetitively-pulsed nanosecond discharge (RPND) in helium over a range of 0.3-16.0 Torr. The discharge was studied experimentally via laser-absorption spectroscopy and opticals emission spectroscopy measurements. In concert with the experimental campaign, a global model of a helium plasma was developed with the aid of particle-in-cell simulations. The global model was then used to predict the population kinetics and emissions of the RPND. Synthesis of the results provided new data and insights on the development of the RPND. Among the results were direct measurements of the triplet metastable states during the excitation period. This period was found to be unexpectedly long at low pressures (less than or equal to 1.0 Torr), suggesting an excess in high-energy electrons as compared to an equilibrium distribution. Other phenomena such as a prominent return stroke and additional energy deposition by reflections in the transmission line were also identified. Estimates of the electric field and electron temperatures were obtained for several conditions. Furthermore, several optical methods for electron temperature measurement were evaluated for application to the discharge. Based on the global model simulations, the coronal model was found to apply to the line ratio of the 33S-23Po and 31S-2 1Po transitions, however further work is needed to ascertain its applicability to experimental discharges. These results provide new insight on the development of the repetitively-pulsed nanosecond discharge. Specifically, they reveal new information about the excited state dynamics within the discharge, the non-equilibrium nature of its electrons, and several avenues for future studies. This study extends the present understanding of repetitively-pulsed discharges, and advances the knowledge of energy coupling between electric fields and plasmas.

  9. Morphological processing of ultraviolet emissions of electrical corona discharge for analysis and diagnostic use.

    Science.gov (United States)

    Schubert, Matthew; Moore, Andrew J

    2016-03-01

    Electron cascades from electrical discharge produce secondary emissions from atmospheric plasma in the ultraviolet band. For a single point of discharge, these emissions exhibit a stereotypical discharge morphology, with latent information about the discharge location. Morphological processing can uncover the location and therefore have diagnostic utility.

  10. Morphological Processing of Ultraviolet Emissions of Electrical Corona Discharge for Analysis and Diagnostic Use

    Science.gov (United States)

    Schubert, Matthew R.; Moore, Andrew J.

    2015-01-01

    Electron cascades from electrical discharge produce secondary emissions from atmospheric plasma in the ultraviolet band. For a single point of discharge, these emissions exhibit a stereotypical discharge morphology, with latent information about the discharge location. Morphological processing can uncover the location and therefore can have diagnostic utility.

  11. Decomposition of dimethyl sulfide in a wire-cylinder pulse corona reactor

    Institute of Scientific and Technical Information of China (English)

    Jian-tao YANG; Yao SHI; Jie CHEN; Qing-fa SU; Da-hui WANG; Jing CAO

    2009-01-01

    Decomposition of dimethyl sulfide (DMS) in air was investigated experimentally by using a wire-cylinder dielectric barrier discharge (DBD) reactor at room temperature and atmospheric pressure. A new type of high pulse voltage source with a thyratron switch and a Blumlein pulse-forming network (BPFN) was adopted in our experiments. The maximum power output of the pulse voltage source and the maximum peak voltage were 1 kW and 100 kV, respectively. The important parameters affecting odor decomposition, including peak voltage, pulse frequency, gas flow rate, initial concentration, and humidity, which influenced the removal efficiency, were investigated. The results showed that DMS could be treated effectively and almost a 100% removal efficiency was achieved at the conditions with an initial concentration of 832 mg/m3 and a gas flow rate of 1000 ml/min. Humidity boosts the removal efficiency and improves the energy yield (EY) greatly. The EY of 832 mg/m3 DMS was 2.87 mg/kJ when the relative humidity was above 30%. In the case of DMS removal, the ozone and nitrogen oxides were observed in the exhaust gas. The carbon and sulfur elements of DMS were mainly converted to carbon dioxide, carbon monoxide and sulfur dioxide. Moreover, sulfur was discovered in the reactor. According to the results, the optimization design for the reactor and the matching of high pulse voltage source can be reckoned.

  12. Cold-cathode, pulsed-power plasma discharge switch

    Science.gov (United States)

    Goebel, Dan M.

    1996-09-01

    CROSSATRONTMmodulator switches are cold-cathode, grid-controlled, plasma-discharge devices that are used for thyratron and hard-tube replacement in high-voltage, pulsed-power applications. CROSSATRON modulator switches have been used to produce square pulses of up to 100 kV and 1000 A, and CROSSATRON laser-discharge switches have switched peak discharge currents of up to 10 kA at 40 kV. The major advantage that CROSSATRON switches offer over other plasma switches is a rapid deionization time that permits high pulse-repetition frequencies (103 to 106 pulses per second depending on the application), and a long life associated with the cold-cathode plasma production mechanism. Compared to hard tubes, CROSSATRON switches have a relatively low forward voltage drop (500 V), the ability to close and open up to 1 kA of peak current, and lower grid-drive power requirements. In this article, we describe the physical mechanisms for how the switch works based on simple models and experimental data. The design of CROSSATRON switches is explained, and characteristic performance in closing and opening applications is described and explained.

  13. Specific interaction between negative atmospheric ions and organic compounds in atmospheric pressure corona discharge ionization mass spectrometry.

    Science.gov (United States)

    Sekimoto, Kanako; Sakai, Mami; Takayama, Mitsuo

    2012-06-01

    The interaction between negative atmospheric ions and various types of organic compounds were investigated using atmospheric pressure corona discharge ionization (APCDI) mass spectrometry. Atmospheric negative ions such as O(2)(-), HCO(3)(-), COO(-)(COOH), NO(2)(-), NO(3)(-), and NO(3)(-)(HNO(3)) having different proton affinities served as the reactant ions for analyte ionization in APCDI in negative-ion mode. The individual atmospheric ions specifically ionized aliphatic and aromatic compounds with various functional groups as atmospheric ion adducts and deprotonated analytes. The formation of the atmospheric ion adducts under certain discharge conditions is most likely attributable to the affinity between the analyte and atmospheric ion and the concentration of the atmospheric ion produced under these conditions. The deprotonated analytes, in contrast, were generated from the adducts of the atmospheric ions with higher proton affinity attributable to efficient proton abstraction from the analyte by the atmospheric ion.

  14. Electrohydrodynamic force produced by a wire-to-cylinder dc corona discharge in air at atmospheric pressure

    Science.gov (United States)

    Moreau, Eric; Benard, Nicolas; Lan-Sun-Luk, Jean-Daniel; Chabriat, Jean-Pierre

    2013-11-01

    Wire-to-cylinder corona discharges are studied to better understand the electrohydrodynamic (EHD) phenomena that govern the performances of electric propulsion systems. First, theory associated with EHD thrusters is presented in order to be compared with experimental results. Secondly, direct thrust measurements are carried out to optimize the electrical and geometrical parameters of such devices. The main results are as follows: (1) the discharge current I is proportional to the square root of the grounded electrode diameter and to 1/d2 where d is the electrode gap; (2) for d ⩽ 20 mm, the mobility of negative ions is higher than that of positive ions while the mobility of both ions is equal for higher gaps; (3) therefore, for gap ⩾30 mm, positive and negative coronas results in the same current-to-thrust conversion; (4) the current-to-thrust conversion is equal to 33 N A-1 per centimetre of gap, and it is proportional to the gap; (5) the thruster effectiveness θ increases with \\sqrt d , decreases with the square root of thrust and reaches about 15 N kW-1 for d = 40 mm (6) the force computed from experimental velocity profiles is overestimated compared with the values measured with a balance, showing that this method cannot be used for thrust determination.

  15. Inactivation of Candida albicans by Corona Discharge: The Increase of Inhibition Zones Area After Far Subsequent Exposition

    Directory of Open Access Journals (Sweden)

    Vladyslava Fantova

    2013-01-01

    Full Text Available The cold atmospheric pressure plasma generated by the negative corona discharge has inhibition effect on the microorganism growth. This effect is well-known and it can be demonstrated on the surface of cultivation agar plates by the formation of inhibition zones. We exposed the cultures of Candida albicans to the negative corona discharge plasma in a special arrangement in this study: The equal doses of plasma were applied subsequently twice or four times on the same culture on one Petri dish, while the distance between exposed points was variable. Only small differences were observed in decontaminated zone areas for twice exposed agar at the shortest distance between exposed points (1.5 cm. In case of the four times exposed agars, we observed significant differences in inhibition zone areas, dependent not only on the exposition site distances, but also on the exposition order. The largest inhibition zone size was observed for the first exposition decreasing to the fourth one. To check relevancy of these dependencies, we presume to conduct further set of experiments with lower yeast concentration. In conclusion, significant difference in partial inhibition zone sizes appeared only when four expositions on one Petri dish were carried out, whereas no significant difference was observed for two subsequent expositions. The explanation of this effect may be the subject of subsequent remote exposition(s, when minute amounts of scattered active particles act on the previously exposed areas; the influence of diffused ozone may also take place.

  16. Corona discharge ion mobility spectrometry with orthogonal acceleration time of flight mass spectrometry for monitoring of volatile organic compounds.

    Science.gov (United States)

    Sabo, Martin; Matejčík, Štefan

    2012-06-19

    We demonstrate the application of corona discharge ion mobility spectrometry with orthogonal acceleration time of flight mass spectrometry (CD IMS-oaTOF) for volatile organic compounds (VOCs) monitoring. Two-dimensional (2D) IMS-oaTOF spectra of VOCs were recorded in nearly real time. The corona discharge atmospheric pressure chemical ionization (APCI) source was operated in positive mode in nitrogen and air. The CD ion source generates in air H(3)O(+)(H(2)O)(n) and NO(+). The NO(+) offers additional possibility for selective ionization and for an increase of the sensitivity of monoaromatic compounds. In addition to H(3)O(+)(H(2)O)(n) and NO(+), we have carried out ionization of VOCs using acetone as dopant gas ((CH(3))(2)COH(+)). Sixteen model VOCs (tetrahydrofuran, butanol, n-propanol, iso-propano, acetone, methanol, ethanol, toluene, benzene, amomnia, dioxan, triethylamine, acetonitrile, formaldehyde, m-xylene, 2,2,2-trifluoroethylamine) were tested using these ionization techniques.

  17. The effect of the electric wind on the spatial distribution of chemical species in the positive corona discharge

    Science.gov (United States)

    Yanallah, K.; Pontiga, F.; Bouazza, M. R.; Chen, J. H.

    2017-08-01

    The electrohydrodynamic air flow generated by a positive corona discharge, and its effect on the spatial distribution of chemical species within a wire-plate corona reactor, have been numerically simulated. The computational model is based on the solutions of the Navier-Stokes equation and the continuity equation of each chemical species generated by the electrical discharge. A simplified analytical expression of the electric force density, which only requires the current density as the input parameter, has been used in the Navier-Stokes equation to obtain the velocity field. For the solution of the continuity equations, a plasma chemistry model that includes the most important reactions between electrons, atoms and molecules in air has been used. Similar to the electric force, the electron density distribution has been approximated by using a semi-analytical expression appropriate for the electrode geometry. The results of the study show that the spatial distribution of chemical species can be very different, and depends on the interplay between the electrohydrodynamic flow, the chemical kinetics of the species and its characteristic lifetime.

  18. Modeling of experimental treatment of acetaldehyde-laden air and phenol-containing water using corona discharge technique.

    Science.gov (United States)

    Faungnawakij, Kajornsak; Sano, Noriaki; Charinpanitkul, Tawatchai; Tanthapanichakoon, Wiwut

    2006-03-01

    Acetaldehyde-laden air and phenol-contaminated water were experimentally treated using corona discharge reactions and gas absorption in a single water-film column. Mathematical modeling of the combined treatment was developed in this work. Efficient removal of the gaseous acetaldehyde was achieved while the corona discharge reactions produced short-lived species such as O and O- as well as ozone. Direct contact of the radicals and ions with water was known to produce aqueous OH radical, which contributes to the decomposition of organic contaminants: phenol, absorbed acetaldehyde, and intermediate byproducts in the water. The influence of initial phenol concentration ranging from 15 to 50 mg L(-1) and that of influent acetaldehyde ranging from 0 to 200 ppm were experimentally investigated and used to build the math model. The maximum energetic efficiency of TOC, phenol, and acetaldehyde were obtained at 25.6 x 10(-9) mol carbon J(-1), 25.0 x 10(-9) mol phenol J(-1), and 2.0 x 10(-9) mol acetaldehyde J(-1), respectively. The predictions for the decomposition of acetaldehyde, phenol, and their intermediates were found to be in good agreement with the experimental results.

  19. Numerical simulation of compact intracloud discharge and generated electromagnetic pulse

    Science.gov (United States)

    Babich, L. P.; Bochkov, E. I.; Kutsyk, I. M.

    2015-06-01

    Using the concept of the relativistic runaway electron avalanche, numerical simulation of compact intracloud discharge as a generator of powerful natural electromagnetic pulses (EMPs) in the HF-UHF range was conducted. We evaluated the numbers of electrons initiating the avalanche, with which the calculated EMP characteristics are consistent with measured ones. The discharge capable of generating EMPs produces runaway electrons in numbers close to those in the source of terrestrial γ-flashes (TGF) registered in the nearest space, which may be an argument for a joint EMP and TGF source.

  20. Propagation of Partial Discharge and Noise Pulses in Turbine Generators

    DEFF Research Database (Denmark)

    Henriksen, Mogens; Stone, G. C.; Kurtz, M.

    1986-01-01

    Changes with time in the partial discharge (PD) activity originating in a generator stator's insulation system provide information about the electrical integrity of the stator winding. It is desirable to measure PD during normal service to minimize costs. To do this successfully, the influence...... of electrical interference must be reduced. Tests are reported which characterize the nature of discharge and noise pulses when using capacitive couplers mounted on each of the phase leads and an RF current transformer mounted on the neutral lead for signal detection. Significant differences between PD...

  1. Investigation of the decolorization efficiency of two pin-to-plate corona discharge plasma system for industrial wastewater treatment

    Energy Technology Data Exchange (ETDEWEB)

    El-Tayeb, A., E-mail: ahmed.khalil@ejust.edu.eg; El-Shazly, A. H.; Elkady, M. F. [Egypt−Japan University of Science and Technology, Chemicals and Petrochemicals Engineering Department (Egypt); Abdel-Rahman, A. B. [Egypt−Japan University of Science and Technology, Electronics and Communications Engineering Department (Egypt)

    2016-09-15

    In this article, a dual pin-to-plate high-voltage corona discharge system is introduced to study experimentally the gap distance, the contact time, the effect of pin and plate materials, the thickness of ground plate and the conductivity on the amount of Acid Blue 25 dye color removal efficiency from polluted water. A study for the optimum air gap distance between dual pin and surface of Acid Blue 25 dye solution is carried out using 3D-EM simulator to find maximum electric field intensity at the tip of both pins. The outcomes display that the best gap for corona discharge is approximately 5 mm for 15-kV source. This separation is constant during the study of other factors. In addition, an investigation of the essential reactive species responsible for oxidation of the dye organic compounds (O{sub 3} in air discharge, O{sub 3} in water, and H{sub 2}O{sub 2}) during the experimental time is conducted. Three various materials such as: stainless steel, copper and aluminum are used for pins and plate. The maximum color removal efficiencies of Acid Blue 25 dyes are 99.03, 82.04, and 90.78% after treatment time 15 min for stainless steel, copper, and aluminum, respectively. Measurement results for the impact of thickness of an aluminum ground plate on color removal competence show color removal efficiencies of 86.3, 90.78, and 98.06% after treatment time 15 min for thicknesses of 2, 0.5, and 0.1 mm, respectively. The increasing of the solution conductivity leads to the reduction of decolorization efficiency. A kinetic model is used to define the performance of corona discharge system. The models of pseudo-zero-order, pseudo-first-order, and pseudo-second-order reaction kinetics are utilized to investigate the decolorization of Acid Blue 25 dye. The rate of degradation of Acid Blue 25 dye follows the pseudo-first-order kinetics in the dye concentration.

  2. Investigation of the decolorization efficiency of two pin-to-plate corona discharge plasma system for industrial wastewater treatment

    Science.gov (United States)

    El-Tayeb, A.; El-Shazly, A. H.; Elkady, M. F.; Abdel-Rahman, A. B.

    2016-09-01

    In this article, a dual pin-to-plate high-voltage corona discharge system is introduced to study experimentally the gap distance, the contact time, the effect of pin and plate materials, the thickness of ground plate and the conductivity on the amount of Acid Blue 25 dye color removal efficiency from polluted water. A study for the optimum air gap distance between dual pin and surface of Acid Blue 25 dye solution is carried out using 3D-EM simulator to find maximum electric field intensity at the tip of both pins. The outcomes display that the best gap for corona discharge is approximately 5 mm for 15-kV source. This separation is constant during the study of other factors. In addition, an investigation of the essential reactive species responsible for oxidation of the dye organic compounds (O3 in air discharge, O3 in water, and H2O2) during the experimental time is conducted. Three various materials such as: stainless steel, copper and aluminum are used for pins and plate. The maximum color removal efficiencies of Acid Blue 25 dyes are 99.03, 82.04, and 90.78% after treatment time 15 min for stainless steel, copper, and aluminum, respectively. Measurement results for the impact of thickness of an aluminum ground plate on color removal competence show color removal efficiencies of 86.3, 90.78, and 98.06% after treatment time 15 min for thicknesses of 2, 0.5, and 0.1 mm, respectively. The increasing of the solution conductivity leads to the reduction of decolorization efficiency. A kinetic model is used to define the performance of corona discharge system. The models of pseudo-zero-order, pseudo-first-order, and pseudo-second-order reaction kinetics are utilized to investigate the decolorization of Acid Blue 25 dye. The rate of degradation of Acid Blue 25 dye follows the pseudo-first-order kinetics in the dye concentration.

  3. Kinetically driven self-assembly of a binary solute mixture with controlled phase separation via electro-hydrodynamic flow of corona discharge.

    Science.gov (United States)

    Jung, Hee Joon; Huh, June; Park, Cheolmin

    2012-10-21

    This feature article describes a new and facile process to fabricate a variety of thin films of non-volatile binary solute mixtures suitable for high performance organic electronic devices via electro-hydrodynamic flow of conventional corona discharge. Both Corona Discharge Coating (CDC) and a modified version of CDC, Scanning Corona Discharge Coating (SCDC), are based on utilizing directional electric flow, known as corona wind, of the charged uni-polar particles generated by corona discharge between a metallic needle and a bottom plate under a high electric field (5-10 kV cm(-1)). The electric flow rapidly spreads out the binary mixture solution on the bottom plate and subsequently forms a smooth and flat thin film in a large area within a few seconds. In the case of SCDC, the static movement of the bottom electrode on which a binary mixture solution is placed provides further control of thin film formation, giving rise to a film highly uniform over a large area. Interesting phase separation behaviors were observed including nanometer scale phase separation of a polymer-polymer binary mixture and vertical phase separation of a polymer-organic semiconductor mixture. Core-shell type phase separation of either polymer-polymer or polymer-colloidal nanoparticle binary mixtures was also developed with a periodically patterned microstructure when the relative location of the corona wind was controlled to a binary solution droplet on a substrate. We also demonstrate potential applications of thin functional films with controlled microstructures by corona coating to various organic electronic devices such as electroluminescent diodes, field effect transistors and non-volatile polymer memories.

  4. Theoretical study of pulsed microwave discharge in nitrogen

    Energy Technology Data Exchange (ETDEWEB)

    Bonaventura, Z; Trunec, D; Mesko, M; Vasina, P; Kudrle, V [Department of Physical Electronics, Faculty of Science, Masaryk University, Kotlarska 2, 611 37 Brno (Czech Republic)

    2005-11-15

    A pulsed microwave discharge burning in pure nitrogen was studied theoretically. The time-dependent Boltzmann equation for electrons was solved numerically in multi-term approximation. It was assumed that the discharge was ignited by a 100 kW microwave (f = 9.4 GHz) pulses with 2.5 {mu}s duration; the repetition frequency was 400 Hz. It was shown that the electron distribution function approaches very quickly the steady state distribution function after a change of the amplitude of electric field intensity. The steady state time averaged values of electron mean energy, diffusion and rate coefficients and drift velocity were calculated for different values of electric field intensity. With these values the actual values of electric field intensity from a previous experiment were determined from the measured time dependence of electron concentration. The calculated values were compared with previous experimental results.

  5. Quantitative relationship between the maximum streamer length and discharge voltage of a pulsed positive streamer discharge in water

    Science.gov (United States)

    Wen, Xiaoqiong; Li, Qian; Li, Jingsen; Ren, Chunsheng

    2017-08-01

    A linear relationship has been realized between the maximum streamer length and discharge voltage of a pulsed positive streamer discharge by measuring the streamer length in water with conductivity of 100 μS cm-1 using high-speed photography. Based on Ohm’s law, a quantitative equation has been derived for the dependence of the maximum streamer length on the discharge voltage of a pulsed positive streamer discharge in water. According to the equation, our results suggest that the streamers spontaneously stop propagating through water due to the voltage at the streamer head dropping below the ignition voltage of a pulsed positive streamer discharge.

  6. International Space Station (ISS) S-Band Corona Discharge Anomaly Consultation

    Science.gov (United States)

    Kichak, Robert A.; Leidecker, Henning; Battel, Steven; Ruitberg, Arthur; Sank, Victor

    2008-01-01

    The Assembly and Contingency Radio Frequency Group (ACRFG) onboard the International Space Station (ISS) is used for command and control communications and transmits (45 dBm or 32 watts) and receives at S-band. The system is nominally pressurized with gaseous helium (He) and nitrogen (N2) at 8 pounds per square inch absolute (psia). MacDonald, Dettwiler and Associates Ltd. (MDA) was engaged to analyze the operational characteristics of this unit in an effort to determine if the anomalous behavior was a result of a corona event. Based on this analysis, MDA did not recommend continued use of this ACRFG. The NESC was requested to provide expert support in the area of high-voltage corona and multipactoring in an S-Band RF system and to assess the probability of corona occurring in the ACRFG during the planned EVA. The NESC recommended minimal continued use of S/N 002 ACRFG until a replacement unit can be installed. Following replacement, S/N 002 will be subjected to destructive failure analysis in an effort to determine the proximate and root cause(s) of the anomalous behavior.

  7. A morphological study of the changes in the ultrastructure of a bacterial biofilm disrupted by an ac corona discharge in air

    Energy Technology Data Exchange (ETDEWEB)

    Stepanova, Olga, E-mail: o.m.stepanova@spbu.ru; Astafiev, Alexander; Kudryavtsev, Anatoly [Physical Faculty, Saint Petersburg State University, St. Petersburg (Russian Federation); Rybalchenko, Oksana; Orlova, Olga; Kapustina, Valentina [Faculty of Medicine, Saint Petersburg State University, St. Petersburg (Russian Federation)

    2016-08-14

    The morphology of bacterial cells and biofilms subjected to a low frequency (∼10{sup 5} Hz) ac (∼10{sup −1} A) corona discharge was investigated using electron microscopy. A low-frequency ac corona discharge in air is shown to have a bactericidal and bacteriostatic effect on Escherichia coli M17 culture at both the cellular and population levels. Corona exposure inhibits the formation of a microbial community and results in the destruction of formed biofilms. This paper presents data on changes in the ultrastructure of cells and biofilms after corona treatment. Our results suggest that the E. coli M17 cells inside biofilms are affected with results similar to sub-lethal and lethal thermal exposure. Some of the biological aspects of colony and biofilm cells death are evaluated. Morphological changes in the ultrastructure of the biofilms under corona treatment are described. Our results indicate that the heating effect is the main factor responsible for the corona-induced inactivation of bacteria.

  8. Influence of air flow parameters on nanosecond repetitively pulsed discharges in a pin-annular electrode configuration

    KAUST Repository

    Heitz, Sylvain A

    2016-03-16

    The effect of various air flow parameters on the plasma regimes of nanosecond repetitively pulsed (NRP) discharges is investigated at atmospheric pressure. The two electrodes are in a pin-annular configuration, transverse to the mean flow. The voltage pulses have amplitudes up to 15 kV, a duration of 10 ns and a repetition frequency ranging from 15 to 30 kHz. The NRP corona to NRP spark (C-S) regime transition and the NRP spark to NRP corona (S-C) regime transition are investigated for different steady and harmonically oscillating flows. First, the strong effect of a transverse flow on the C-S and S-C transitions, as reported in previous studies, is verified. Second, it is shown that the azimuthal flow imparted by a swirler does not affect the regime transition voltages. Finally, the influence of low frequency harmonic oscillations of the air flow, generated by a loudspeaker, is studied. A strong effect of frequency and amplitude of the incoming flow modulation on the NRP plasma regime is observed. Results are interpreted based on the cumulative effect of the NRP discharges and an analysis of the residence times of fluid particles in the inter-electrode region. © 2016 IOP Publishing Ltd.

  9. Characteristics of back corona discharge in a honeycomb catalyst and its application for treatment of volatile organic compounds.

    Science.gov (United States)

    Feng, Fada; Zheng, Yanyan; Shen, Xinjun; Zheng, Qinzhen; Dai, Shaolong; Zhang, Xuming; Huang, Yifan; Liu, Zhen; Yan, Keping

    2015-06-02

    The main technical challenges for the treatment of volatile organic compounds (VOCs) with plasma-assisted catalysis in industrial applications are large volume plasma generation under atmospheric pressure, byproduct control, and aerosol collection. To solve these problems, a back corona discharge (BCD) configuration has been designed to evenly generate nonthermal plasma in a honeycomb catalyst. Voltage-current curves, discharge images, and emission spectra have been used to characterize the plasma. Grade particle collection results and flow field visualization in the discharge zones show not only that the particles can be collected efficiently, but also that the pressure drop of the catalyst layer is relatively low. A three-stage plasma-assisted catalysis system, comprising a dielectric barrier discharge (DBD) stage, BCD stage, and catalyst stage, was built to evaluate toluene treatment performance by BCD. The ozone analysis results indicate that BCD enhances the ozone decomposition by collecting aerosols and protecting the Ag-Mn-O catalyst downstream from aerosol contamination. The GC and FTIR results show that BCD contributes to toluene removal, especially when the specific energy input is low, and the total removal efficiency reaches almost 100%. Furthermore, this removal results in the emission of fewer byproducts.

  10. IR-LAS Measurements of a Pulsed Xenon Discharge Plasma

    Science.gov (United States)

    Jinno, Masafumi; Wada, Ryota; Motomura, Hideki; Aono, Masaharu

    As a first step to understand the processes taking place in a pulsed xenon discharge, the temporal behavior of the radial metastable atom distribution in a xenon lamp was measured by IR laser absorption spectroscopy. During the first 10μs after starting the discharge, high electron density and the depletion of the ground state atoms at the center of the discharge brought about an almost flat distribution of the metastable atoms within the half-radius area. Following that, the metastable atom density became higher at the center than outside because of recombination between electrons and ions. After the metastable density increase and following voltage cut off, the metastable density decreases again. Considering the diffusion equation alongside these results, it becomes clear that the decrease of the metastable density is caused by quenching to the resonace level from the metastable level or three-body collisions forming excimers.

  11. Supression of laser breakdown by pulsed nonequilibrium ns discharge

    Science.gov (United States)

    Starikovskiy, A. Y.; Semenov, I. E.; Shneider, M. N.

    2016-10-01

    The avalanche ionization induced by infrared laser pulses was investigated in a pre-ionized argon gas. Pre-ionization was created by a high-voltage pulsed nanosecond discharge developed in the form of a fast ionization wave. Then, behind the front of ionization wave additional avalanche ionization was initiated by the focused Nd-YAG laser pulse. It was shown that the gas pre-ionization inhibits the laser spark generation. It was demonstrated that the suppression of laser spark development in the case of strong gas pre-ionization is because of fast electron energy transfer from the laser beam focal region. The main mechanism of this energy transfer is free electrons diffusion.

  12. The CRRES IDM spacecraft experiment for insulator discharge pulses. [Internal Discharge Monitor

    Science.gov (United States)

    Frederickson, A. R.; Mullen, E. G.; Kerns, K. J.; Robinson, P. A.; Holeman, E. G.

    1993-01-01

    The Internal Discharge Monitor (IDM) is designed to observe electrical pulses from common electrical insulators in space service. The characteristics of the instrument are described. The IDM was flown on the Combined Release and Radiation Effects Satellite (CRRES). The sixteen insulator samples included G10 circuit boards, FR4 and PTFE fiberglass circuit boards, FEP Teflon, alumina, and wires with common insulations. The samples are fully enclosed, mutually isolated, and space radiation penetrates 0.02 cm of aluminum before striking the samples. Published data in the literature provides a simple method for determining the flux of penetrating electrons. The pulse rate is compared to the penetrating flux of electrons.

  13. High-voltage electrode optimization towards uniform surface treatment by a pulsed volume discharge

    Science.gov (United States)

    Ponomarev, A. V.; Pedos, M. S.; Scherbinin, S. V.; Mamontov, Y. I.; Ponomarev, S. V.

    2015-11-01

    In this study, the shape and material of the high-voltage electrode of an atmospheric pressure plasma generation system were optimised. The research was performed with the goal of achieving maximum uniformity of plasma treatment of the surface of the low-voltage electrode with a diameter of 100 mm. In order to generate low-temperature plasma with the volume of roughly 1 cubic decimetre, a pulsed volume discharge was used initiated with a corona discharge. The uniformity of the plasma in the region of the low-voltage electrode was assessed using a system for measuring the distribution of discharge current density. The system's low-voltage electrode - collector - was a disc of 100 mm in diameter, the conducting surface of which was divided into 64 radially located segments of equal surface area. The current at each segment was registered by a high-speed measuring system controlled by an ARM™-based 32-bit microcontroller. To facilitate the interpretation of results obtained, a computer program was developed to visualise the results. The program provides a 3D image of the current density distribution on the surface of the low-voltage electrode. Based on the results obtained an optimum shape for a high-voltage electrode was determined. Uniformity of the distribution of discharge current density in relation to distance between electrodes was studied. It was proven that the level of non-uniformity of current density distribution depends on the size of the gap between electrodes. Experiments indicated that it is advantageous to use graphite felt VGN-6 (Russian abbreviation) as the material of the high-voltage electrode's emitting surface.

  14. Direct and Efficient Dehydrogenation of Tetrahydroquinolines and Primary Amines Using Corona Discharge Generated on Ambient Hydrophobic Paper Substrate

    Science.gov (United States)

    Davis, Kathryn M.; Badu-Tawiah, Abraham K.

    2016-10-01

    The exposure of an aqueous-based liquid drop containing amines and graphite particles to plasma generated by a corona discharge results in heterogeneous aerobic dehydrogenation reactions. This green oxidation reaction occurring in ambient air afforded the corresponding quinolines and nitriles from tetrahydroquinolines and primary amines, respectively, at >96% yields in less than 2 min of reaction time. The accelerated dehydrogenation reactions occurred on the surface of a low energy hydrophobic paper, which served both as container for holding the reacting liquid drop and as a medium for achieving paper spray ionization of reaction products for subsequent characterization by ambient mass spectrometry. Control experiments indicate superoxide anions (O2 •-) are the main reactive species; the presence of graphite particles introduced heterogeneous surface effects, and enabled the efficient sampling of the plasma into the grounded analyte droplet solution.

  15. Direct and Efficient Dehydrogenation of Tetrahydroquinolines and Primary Amines Using Corona Discharge Generated on Ambient Hydrophobic Paper Substrate

    Science.gov (United States)

    Davis, Kathryn M.; Badu-Tawiah, Abraham K.

    2017-04-01

    The exposure of an aqueous-based liquid drop containing amines and graphite particles to plasma generated by a corona discharge results in heterogeneous aerobic dehydrogenation reactions. This green oxidation reaction occurring in ambient air afforded the corresponding quinolines and nitriles from tetrahydroquinolines and primary amines, respectively, at >96% yields in less than 2 min of reaction time. The accelerated dehydrogenation reactions occurred on the surface of a low energy hydrophobic paper, which served both as container for holding the reacting liquid drop and as a medium for achieving paper spray ionization of reaction products for subsequent characterization by ambient mass spectrometry. Control experiments indicate superoxide anions (O2 •-) are the main reactive species; the presence of graphite particles introduced heterogeneous surface effects, and enabled the efficient sampling of the plasma into the grounded analyte droplet solution.

  16. Treatment of Wastewater with High Conductivity by Pulsed Discharge Plasma

    Science.gov (United States)

    Wang, Zhaojun; Jiang, Song; Liu, Kefu

    2014-07-01

    A wastewater treatment system was established by means of pulsed dielectric barrier discharge (DBD). The main advantage of this system is that the wastewater is employed as one of the electrodes for the degradation of rhodamine B, which makes use of the high conductivity and lessenes its negative influence on the discharge process. At the same time, the reactive species like ozone and ultraviolet (UV) light generated by the DBD can be utilized for the treatment of wastewater. The effects of some factors like conductivity, peak pulse voltage, discharge frequency and pH values were investigated. The results show that the combination of these reactive species could enhance the degradation of the dye while the ozone played the most important role in the process. The degradation efficiency was enhanced with the increase of energy supplied. The reduction in the concentration of rhodamine B was much more effective with high solution conductivity; under the highest conductivity condition, the degradation rate could rise to 99%.

  17. Progress of long pulse discharges by ECH in LHD

    Science.gov (United States)

    Yoshimura, Y.; Kasahara, H.; Tokitani, M.; Sakamoto, R.; Ueda, Y.; Ito, S.; Okada, K.; Kubo, S.; Shimozuma, T.; Igami, H.; Takahashi, H.; Tsujimura, T. I.; Makino, R.; Kobayashi, S.; Mizuno, Y.; Akiyama, T.; Ashikawa, N.; Masuzaki, S.; Motojima, G.; Shoji, M.; Suzuki, C.; Tanaka, H.; Tanaka, K.; Tokuzawa, T.; Tsuchiya, H.; Yamada, I.; Goto, Y.; Yamada, H.; Mutoh, T.; Komori, A.; Takeiri, Y.; the LHD Experiment Group

    2016-04-01

    Using ion cyclotron heating and electron cyclotron heating (ECH), or solo ECH, trials of steady state plasma sustainment have been conducted in the superconducting helical/stellarator, large helical device (LHD) (Ida K et al 2015 Nucl. Fusion 55 104018). In recent years, the ECH system has been upgraded by applying newly developed 77 and 154 GHz gyrotrons. A new gas fueling system applied to the steady state operations in the LHD realized precise feedback control of the line average electron density even when the wall condition varied during long pulse discharges. Owing to these improvements in the ECH and the gas fueling systems, a stable 39 min discharge with a line average electron density n e_ave of 1.1  ×  1019 m-3, a central electron temperature T e0 of over 2.5 keV, and a central ion temperature T i0 of 1.0 keV was successfully performed with ~350 kW EC-waves. The parameters are much improved from the previous 65 min discharge with n e_ave of 0.15  ×  1019 m-3 and T e0 of 1.7 keV, and the 30 min discharge with n e_ave of 0.7  ×  1019 m-3 and T e0 of 1.7 keV.

  18. 电晕脉冲干扰特性的实验研究%EXPERIMENTAL INVESTIGATION ON INTERFERENCE CHARACTERISTIC OF CORONA PULSES

    Institute of Scientific and Technical Information of China (English)

    宋小坚

    2001-01-01

    本文采用模拟实验的方法,分析了不同极性单个电晕脉冲产生的干扰水平和频域范围,指出正电晕脉冲是干扰的主要来源,膜状电晕的产生能有效地抑制干扰,气候条件对电晕干扰水平的影响有限。%Interference lever and frequency spectrum of single corona pulse with different polarity are analyzed through the method of experiment in this paper. The experimental results show that the positive corona pulse is the main source of interference, and film corona can be used to restrain interference, while weather condition has very limited influence on the corona interference level.

  19. The Study of Active Atoms in High-Voltage Pulsed Coronal Discharge by Optical Diagnostics

    Institute of Scientific and Technical Information of China (English)

    Liu Feng; Wang Wenchun; Wang Su; Ren Chunsheng; Wang Younian

    2005-01-01

    In this study, the emission spectra of active atoms O (3p5P → 3s5S20 777.4 nm),Ha (3P → 2S 656.3 nm) and N (3p4P → 3s4S0 742.3 nm, 744.2 nm, 746.8 nm) produced by thepositive high-voltage pulsed corona discharge (HVPCD) of N2 and H2O mixture in a needle-platereactor have successfully been recorded against a severe electromagnetic interference coming fromthe HVPCD at one atmosphere. The effects of the peak voltage, the repetition rate of pulseddischarge and the flow rate of oxygen on the production of those active atoms are investigated. Itis found that when the peak voltage and the repetition rate of the pulsed discharge are increased,the emission intensities of those active atoms rise correspondingly. And the emission intensities ofO (3p5P → 3s5S20 777.4 nm), Ha (3P → 2S 656.3 nm) and N (3p4P → 3s4S0 742.3 nm, 744.2 nm,746.8 nm) increase with the flow rate of oxygen (from 0 to 25 ml/min) and achieve a maximumvalue at a flow rate of 25 ml/min. When the flow rate of oxygen is increased further, the emissionintensities of those atoms visibly decrease correspondingly. The main physicochemical processesof interaction involved between electrons, neutrals and ions are also discussed.

  20. Pulsed microwave discharges in powder mixtures: Status, problems, and prospects

    Science.gov (United States)

    Batanov, G. M.; Kossyi, I. A.

    2015-10-01

    Results of experiments on the excitation of pulsed microwave discharges by gyrotron radiation (λ = 4 mm, P 0 = 100-500 kW, τ = 1-10 ms) in the volumes and on the surfaces of metal-dielectric powder mixtures are presented. It is shown that there are two phases of discharge development: the spark phase, accompanied by a partial evaporation of the powder material, and the phase of a developed discharge, characterized by a plasma density of ˜1017 cm-3, high absorption, and high temperatures (˜5-10 kK) in a thin layer (˜0.1-0.2 mm) of plasma and vapor. It is demonstrated that the conductivity induced in the targets by UV radiation play an important role in the microwave absorption by powder grains. It is found that, in the course of the discharge, a conductive metal mesh forms in the powder volume as a result of metal evaporation. Reactions of high-temperature synthesis were initiated in various powder mixtures (Ti + B, Al + Fe2O3, Mo + B, etc.). It is shown that the reactions of high-temperature synthesis last for up to 0.1 s and are accompanied by the evaporation of powder grains and the formation of an aerosol cloud due to free expansion of reactants from the sample surface. The possibility of experimentally studying the kinetics of reactions of high-temperature synthesis is demonstrated. It is noticed that microwave discharges can be used to initiate plasmachemical reactions on the surfaces of radioparent materials in active gaseous media.

  1. Plasma Catalysis of Methane Decomposition in Pulse Microwave Discharge

    Science.gov (United States)

    Potapkin, B.; Rusanov, V.; Jivotov, V.; Babaritski, A.; Potechin, S.; Etievant, C.

    1997-10-01

    Investigation of plasma catalysis effects in various chemical reactions, such as SO2 and hydrocarbons oxidation, ammonia and nitrogen oxides synthesis, has been of interest for many decades. Present work describes the first experimental observation and theoretical analysis of plasma catalysis effects in the case of endothermic methane decomposition into molecular hydrogen and carbon black. Process energy requirements are coverd mainly by low potential gas thermal energy while plasma is used for acceleration of chemical reactions via active species generation. The experiments were done as follows: (i) methane was preheated in a conventional heat exchanger up to about 40-65 ^oC where thermal methane decomposition is limited by process kinetics, (ii) methane was passed through a non-equilibrium pulse microwave discharge (9.04 GHz, pulse duration 1 μs). Experiments have shown a strong catalytic effect of plasma on methane decomposition. The degree of conversion after discharge increased drastically, despite gas cooling, because of heat absorption in the methane decomposition reaction. Theoretical analysis of process kinetics and energy balance gave clear evidence of the catalytic effect of plasma under experimental conditions. The estimated chain length was about 300. The possible mechanism of plasma catalysis, the ion-molecular chain Winchester mechanism, is proposed and described.

  2. Removal of NO2 and O3 generated from corona discharge in indoor air cleaning with MnO2 catalyst

    Science.gov (United States)

    Ge, H.; Yu, R.; Mi, D.; Zhu, Y. M.

    2013-03-01

    The production rules and removal efficiency of harmful byproducts such as NO2 and O3 generated from DC corona discharge in indoor air cleaning were investigated. The production behaviours of NO2 and O3 and the relationship between the amount of catalyst (MnO2) and the removal rate of harmful byproducts were experimentally studied. Further, indoor application tests were carried out in a closed room with 90 m3. The results showed that the concentrations of NO2 and O3 produced by corona discharge linearly increased with discharge time. The NO2 yield is larger than O3 by almost one order of magnitude under the same discharge power. To satisfy the demand of Standard of Indoor Air Quality (GB/T18883-2002), the power consumption of unit volume should be less than 1 W m-3 and the catalyst MnO2 consumptions in positive-negative corona discharge were 200 cm3 W-1 and 100 cm3 W-1, respectively.

  3. Elimination of sulphur odours at landfills by bioconversion and the corona discharge plasma technique.

    Science.gov (United States)

    Xia, Fangfang; Liu, Xin; Kang, Ying; He, Ruo; Wu, Zucheng

    2015-01-01

    Hydrogen sulphide (H2S) contributes a lot to odours at landfills, which is a threat to the environment and the health of the staff therein. To mitigate its emission, the bioconversion within landfill cover soils (LCSs) was introduced. H2S emission and concentration both in the field air above the landfill and in microcosm testing were surveyed. Results indicated that H2S emission and concentration in the landfill varied with landfill seasons and sites. There existed relationship between H2S concentration and fluxes spatially and temporally. To characterize and assess the spatial and temporal diversity of sulphur-oxidizing bacteria (SOB) and sulphate-reducing bacteria (SRB) in the LCSs, the terminal-restriction fragment length polymorphism technique was employed. Using the functional genes of dsrB and soxB, SOB, including Halothiobacillus, Rhodothalassium, Paracocccus, Allochromatium, and Thiobacillus, and SRB, including Desulfovibrio, Syntrophobacter, Desulfomonile and Desulfobacca, were identical and exhibited the dominant role in the LCSs. By employing an alternative available corona reactor, more than 90% removal efficiencies of sulphides were demonstrated, suggesting that the LCSs for eliminating odours in a lower concentration would be feasible.

  4. Optical visualization and electrical characterization of fast-rising pulsed dielectric barrier discharge for airflow control applications

    Science.gov (United States)

    Benard, Nicolas; Zouzou, Nourredine; Claverie, Alain; Sotton, Julien; Moreau, Eric

    2012-02-01

    Flow control consists of manipulating flows in an effective and robust manner to improve the global performances of transport systems or industrial processes. Plasma technologies, and particularly surface dielectric barrier discharge (DBD), can be a good candidate for such purpose. The present experimental study focuses on optical and electrical characterization of plasma sheet formed by applying a pulse of voltage with rising and falling periods of 50 ns for a typical surface DBD geometry. Positive and negative polarities are compared in terms of current behavior, deposited energy, fast-imaging of the plasma propagation, and resulting modifications of the surrounding medium by using shadowgraphy acquisitions. Positive and negative pulses of voltage produce streamers and corona type plasma, respectively. Both of them result in the production of a localized pressure wave propagating in the air with a speed maintained at 343 m/s (measurements at room temperature of 20 °C). This suggests that the produced pressure wave can be considered as a propagating sound wave. The intensity of the pressure wave is directly connected to the dissipated energy at the dielectric wall with a linear increase with the applied voltage amplitude and a strong dependence toward the rising time. At constant voltage amplitude, the pressure wave is reinforced by using a positive pulse. The present investigation also reveals that rising and decaying periods of a single pulse of voltage result in two distinct pressure waves. As a result, superposition or successive pressure wave can be produced by adjusting the width of the pulse.

  5. Investigating Pulsed Discharge Polarity Employing Solid-State Pulsed Power Electronics

    DEFF Research Database (Denmark)

    Davari, Pooya; Zare, Firuz; Blaabjerg, Frede

    2015-01-01

    . In this paper, effects of applied voltage polarity on plasma discharge have been investigated in different mediums at atmospheric pressure. The experiments have been conducted based on high voltage DC power supply and high voltage pulse generator for point-to-point and point-to-plane geometries. Furthermore......, the influence of electric field distribution is analyzed using Finite Element simulations for the employed geometries and mediums. The experimental and simulation results have verified the important role of the applied voltage polarity, employed geometry and medium of the system on plasma generation....... condition plays an important role in maintaining the desired performance. Investigating the system parameters contributed to the generated pulses is an effective way in improving the system performance further ahead. One of these parameters is discharge polarity which has received less attention...

  6. Triggering and guiding electric discharge by a train of UV picosecond pulses combined with a long UV pulse

    CERN Document Server

    Ionin, A A; Levchenko, A O; Seleznev, L V; Shutov, A V; Sinitsyn, D V; Smetanin, I V; Ustinovsky, N N; Zvorykin, V D

    2012-01-01

    Non-self-sustained electric discharge and electric breakdown were triggered and guided by a train of picosecond UV pulses overlapped with a long free-running UV pulse of a hybrid Ti:Sapphire-KrF laser facility. Photocurrent sustained by this train is two orders of magnitude higher, and electric breakdown distance is twice longer than those for the discharge triggered by the long UV pulse only.

  7. Effect of flow rate on the characteristics of rep etitive microsecond-pulse gliding discharges%气流对微秒脉冲滑动放电特性的影响∗

    Institute of Scientific and Technical Information of China (English)

    牛宗涛; 章程; 马云飞; 王瑞雪; 陈根永; 严萍; 邵涛

    2015-01-01

    Gliding discharges driven by microsecond-pulse power supply can generate non-thermal plasmas with high energy and high power density at atmospheric pressure. However, the flowing air significantly influences the characteristics of the microsecond-pulse gliding discharges in a repetitive mode. In this paper, in order to obtain the characteristics of the microsecond-pulse gliding discharges in a needle-to-needle gap, a microsecond-pulse power supply with an output voltage up to 30 kV, a pulse width ∼8 µs, and a pulse repetition frequencies 1–3000 Hz is used to investigate the electrical characteristics of gliding discharges by analyzing the voltage-current waveforms and obtaining the discharge images. Experimental results show that there are three typical discharge modes in the microsecond-pulse gliding discharges as the applied voltage increases, i.e. corona discharge, diffuse discharge, and gliding-like discharge. Both voltage-current waveforms and the discharge images at different discharge modes have significantly different behaviors. Corona discharge only exists near the positive electrode with a small radius of curvature. Diffuse discharges behave as the overlapped plasma channels bridge the entire gap. The channel of diffuse discharge is full of gap, which starts from the positive electrode, spreads in all directions, and ends at the negative electrode. Gliding-like discharge behaves as a continuous spark channeling, showing a continuous spark, which is discharging strongly and influenced by flow rates. Furthermore, both pulse repetition frequency (PRF) and flow rate remarkably affects the characteristics of microsecond-pulse gliding discharges. When the flow rate is small (2 L/min), the spark channels of gliding-like discharge gradually concentrate with the increase of the PRF. However, when the flow rate is larger (16 L/min), the spark channels of gliding-like discharge behave dispersively when the PRF increases. In our opinion, different

  8. Vacuum Ultraviolet Xenon Excimer Light Source Excited by a Pulsed Jet Discharge

    National Research Council Canada - National Science Library

    Eiji FUTAGAMI; Toshiaki TAKADA; Junji KAWANAKA; Shoichi KUBODERA; Wataru SASAKI; Kou KUROSAWA; Kenichi MITSUHASHI; Tatsushi IGARASHI

    1995-01-01

      We have developed a new xenon excimer light source in vacuum ultraviolet (VUV). The use of a pulsed gas jet discharge realized efficient cluster excitation and spatially localized emission in VUV with an extremely long pulse duration...

  9. Characterisation of the protein corona using tunable resistive pulse sensing: determining the change and distribution of a particle's surface charge.

    Science.gov (United States)

    Blundell, Emma L C J; Healey, Matthew J; Holton, Elizabeth; Sivakumaran, Muttuswamy; Manstana, Sarabjit; Platt, Mark

    2016-08-01

    The zeta potential of the protein corona around carboxyl particles has been measured using tunable resistive pulse sensing (TRPS). A simple and rapid assay for characterising zeta potentials within buffer, serum and plasma is presented monitoring the change, magnitude and distribution of proteins on the particle surface. First, we measure the change in zeta potential of carboxyl-functionalised nanoparticles in solutions that contain biologically relevant concentrations of individual proteins, typically constituted in plasma and serum, and observe a significant difference in distributions and zeta values between room temperature and 37 °C assays. The effect is protein dependent, and the largest difference between the two temperatures is recorded for the γ-globulin protein where the mean zeta potential changes from -16.7 to -9.0 mV for 25 and 37 °C, respectively. This method is further applied to monitor particles placed into serum and/or plasma. A temperature-dependent change is again observed with serum showing a 4.9 mV difference in zeta potential between samples incubated at 25 and 37 °C; this shift was larger than that observed for samples in plasma (0.4 mV). Finally, we monitor the kinetics of the corona reorientation for particles initially placed into serum and then adding 5 % (V/V) plasma. The technology presented offers an interesting insight into protein corona structure and kinetics of formation measured in biologically relevant solutions, i.e. high protein, high salt levels, and its particle-by-particle analysis gives a measure of the distribution of particle zeta potential that may offer a better understanding of the behaviour of nanoparticles in solution. Graphical Abstract The relative velocity of a nanoparticle as it traverses a nanopore can be used to determine its zeta potential. Monitoring the changes in translocation speeds can therefore be used to follow changes to the surface chemistry/composition of 210 nm particles that were placed

  10. Characteristics of Nanosecond Pulsed Discharges in Atmospheric Helium Microplasmas

    Science.gov (United States)

    Manish, Jugroot

    2016-10-01

    Microplasmas are very interesting due to their unique properties and achievable regimes maintained at atmospheric pressures. Due to the small scales, numerical modeling could contribute to the understanding of underlying phenomena as it provides access to local parameters—and complements experimental global characteristics. A self-consistent formalism, applied to nanosecond pulsed atmospheric non-equilibrium helium plasmas, reveals that several successive discharges can persist as a result of a combined volume and dielectric surface effects. The valuable insights provided by the spatiotemporal simulation results show the critical importance of coupled gas and plasma dynamics—namely gas heating and electric field reversals. supported by the Natural Sciences and Engineering Research Council of Canada (NSERC) — Discovery Grant (No. 342369)

  11. Recycled Coarse Aggregate Produced by Pulsed Discharge in Water

    Science.gov (United States)

    Namihira, Takao; Shigeishi, Mitsuhiro; Nakashima, Kazuyuki; Murakami, Akira; Kuroki, Kaori; Kiyan, Tsuyoshi; Tomoda, Yuichi; Sakugawa, Takashi; Katsuki, Sunao; Akiyama, Hidenori; Ohtsu, Masayasu

    In Japan, the recycling ratio of concrete scraps has been kept over 98 % after the Law for the Recycling of Construction Materials was enforced in 2000. In the present, most of concrete scraps were recycled as the Lower Subbase Course Material. On the other hand, it is predicted to be difficult to keep this higher recycling ratio in the near future because concrete scraps increase rapidly and would reach to over 3 times of present situation in 2010. In addition, the demand of concrete scraps as the Lower Subbase Course Material has been decreased. Therefore, new way to reuse concrete scraps must be developed. Concrete scraps normally consist of 70 % of coarse aggregate, 19 % of water and 11 % of cement. To obtain the higher recycling ratio, the higher recycling ratio of coarse aggregate is desired. In this paper, a new method for recycling coarse aggregate from concrete scraps has been developed and demonstrated. The system includes a Marx generator and a point to hemisphere mesh electrode immersed in water. In the demonstration, the test piece of concrete scrap was located between the electrodes and was treated by the pulsed discharge. After discharge treatment of test piece, the recycling coarse aggregates were evaluated under JIS and TS and had enough quality for utilization as the coarse aggregate.

  12. Feasibility of corona discharge ion mobility spectrometry for direct analysis of samples extracted by dispersive liquid-liquid microextraction.

    Science.gov (United States)

    Jafari, Mohammad T; Riahi, Farhad

    2014-05-23

    The capability of corona discharge ionization ion mobility spectrometry (CD-IMS) for direct analysis of the samples extracted by dispersive liquid-liquid microextraction (DLLME) was investigated and evaluated, for the first time. To that end, an appropriate new injection port was designed and constructed, resulting in possibility of direct injection of the known sample volume, without tedious sample preparation steps (e.g. derivatization, solvent evaporation, and re-solving in another solvent…). Malathion as a test compound was extracted from different matrices by a rapid and convenient DLLME method. The positive ion mobility spectra of the extracted malathion were obtained after direct injection of carbon tetrachloride or methanol solutions. The analyte responses were compared and the statistical results revealed the feasibility of direct analysis of the extracted samples in carbon tetrachloride, resulting in a convenient methodology. The coupled method of DLLME-CD-IMS was exhaustively validated in terms of sensitivity, dynamic range, recovery, and enrichment factor. Finally, various real samples of apple, river and underground water were analyzed, all verifying the feasibility and success of the proposed method for the easy extraction of the analyte using DLLME separation before the direct analysis by CD-IMS.

  13. Influence Factors of Audible Noise Caused by Corona Discharge on UHVDC Transmission Lines Under High Altitude Condition

    Institute of Scientific and Technical Information of China (English)

    TIAN Feng; YU Zhanqing; ZENG Rong; LIU Lei; LI Min; LI Ruihai

    2012-01-01

    Audible noises (AN) generated by corona discharges on ultra high voltage direct current (UHVDC) transmission lines is one of the key issues of UHVDC power projects. Experimental results were obtained synchronously by 10 Briiel & Kjeer outdoor AN instruments under the full-scale test lines in National Laboratory for UHV Technology in Kunming at an altitude of 2 100 m. Long-term statistical measurements of the AN level were performed almost 24 hours a day and 5 ~ 6 days a week in 2 years. Influences of voltage, line configurations, temperature and humidity on the characteristics of AN levels were analysed. The measurement results show that the AN level rises with increasing line voltage, decreasing minimum conductor height and increasing bundle radius. The pole spacing has no significant influence on the peak value of the AN level. The AN level varies about _+ 1 dB in the temperature range of 15~22℃, and no more than ±2 dB within 6.8~24.4 ℃. The results also indicate that in a relative low range of absolute humidity, about 5 ~ 7. 99 g/ma, the AN level fluctuates slightly at different measurement points. However, in a relative high absolute humidity range, about 8 ~ 11. 5 g/ma, the AN level decreases with the increase of absolute humidity.

  14. Trace analysis of organics in air by corona discharge atmospheric pressure ionization using an electrospray ionization interface.

    Science.gov (United States)

    Nikolaev, Eugene; Riter, Leah S; Laughlin, Brian C; Handberg, Eric; Cooks, R Graham

    2004-01-01

    A corona discharge ion source operating at atmospheric pressure in the point-to-plane configuration was constructed by reconfiguring the ion source of a commercial electrospray ionization (ESI) quadrupole mass spectrometer. This new source allows direct air analysis without modification to the mass spectrometer. Detection and quantitation of semi-volatile compounds in air is demonstrated. The analytical performance of the system was established using the chemical warfare agent simulants methyl salicylate and dimethyl methylphosphonate. Limits of detection are 60 pptr in the negative-ion mode and 800 pptr in the positive-ion mode for methyl salicylate and 800 pptr in the negative-ion mode and 3.6 ppb in the positive-ion mode for dimethyl methylphosphonate. A linear response was observed from 60 pptr to 8 ppb for methyl salicylate in air in the negative-ionization mode. Cluster ion formation versus production of analyte ions was investigated and it was found that dry air or an elevated capillary interface temperature (130 degrees C) was needed to avoid extensive clustering, mostly of water. Reagent gases are not needed as proton sources, as is usually the case for atmospheric pressure chemical ionization, and this, together with the simplicity, sensitivity and speed of the technique, makes it promising for miniaturization and future field studies.

  15. A corona discharge atmospheric pressure chemical ionization source with selective NO(+) formation and its application for monoaromatic VOC detection.

    Science.gov (United States)

    Sabo, Martin; Matejčík, Štefan

    2013-11-21

    We have developed a new type of corona discharge (CD) for atmospheric pressure chemical ionization (APCI) for application in ion mobility spectrometry (IMS) as well as in mass spectrometry (MS). While the other CD-APCI sources are able to generate H3O(+)·(H2O)n as the major reactant ions in N2 or in zero air, the present CD-APCI source has the ability to generate up to 84% NO(+)·(H2O)n reactant ions in zero air. The change of the working gas from zero air to N2 allows us to change the major reactant ions from NO(+)·(H2O)n to H3O(+)·(H2O)n. In this paper we present the description of the new CD-APCI and discuss the processes associated with the NO(+) formation. The selective formation of NO(+)·(H2O)n reactant ions offers chemical ionization based on these ions which can be of great advantage for some classes of chemicals. We demonstrate here a significant increase in the sensitivity of the IMS-MS instrument for monoaromatic volatile organic compound (VOC) detection upon NO(+)·(H2O)n chemical ionization.

  16. Nitric oxide-assisted atmospheric pressure corona discharge ionization for the analysis of automobile hydrocarbon emission species.

    Science.gov (United States)

    Dearth, M A; Komiski, T J

    1994-12-01

    Nitric oxide reagent gas has been found to improve the sensitivity and robustness of the atmospheric pressure corona discharge ionization (APCDI) process. Sensitivity has been increased by a factor of 20-100, depending on the compound, over APCDI without nitric oxide. The robustness (defined as the sensitivity to matrix interferences) of APCDI in the presence of water has been improved by a factor of 3 over normal APCDI. These improvements are due in part to a modification of the commercial inlet system and ionization chamber that allows the chamber and sample gases to be heated to 100 and 350°C, respectively. Nitric oxide was chosen as the reagent gas because of the variety and selectivity of its interaction with hydrocarbons with differing functional groups. Product ions of nitric oxide ionization and their subsequent tandem mass spectra are presented and discussed for selected alkanes; alkenes, alkylbenzenes, alcohols; aldehydes, and an ether. A tandem mass spectrometry (unique parent ion-daughter ion transition) method was developed to quantify compounds of specific interest in vehicle emissions. The absolute sensitivity for these compounds, under ideal conditions, was determined and ranges from 0.006 ppb for xylene (most sensitive) to 80 ppb for C8 (or larger) normal alkanes. Routine sensitivity for real-world samples was in the single parts per billion range for aromatic and olefinic species. Potential applications include the real-time, on-line monitoring of selected hydrocarbons in automobile exhaust.

  17. Collision-induced dissociation analysis of negative atmospheric ion adducts in atmospheric pressure corona discharge ionization mass spectrometry.

    Science.gov (United States)

    Sekimoto, Kanako; Takayama, Mitsuo

    2013-05-01

    Collision-induced dissociation (CID) experiments were performed on atmospheric ion adducts [M + R](-) formed between various types of organic compounds M and atmospheric negative ions R(-) [such as O2(-), HCO3(-), COO(-)(COOH), NO2(-), NO3(-), and NO3(-)(HNO3)] in negative-ion mode atmospheric pressure corona discharge ionization (APCDI) mass spectrometry. All of the [M + R](-) adducts were fragmented to form deprotonated analytes [M - H](-) and/or atmospheric ions R(-), whose intensities in the CID spectra were dependent on the proton affinities of the [M - H](-) and R(-) fragments. Precursor ions [M + R](-) for which R(-) have higher proton affinities than [M - H](-) formed [M - H](-) as the dominant product. Furthermore, the CID of the adducts with HCO3(-) and NO3(-)(HNO3) led to other product ions such as [M + HO](-) and NO3(-), respectively. The fragmentation behavior of [M + R](-) for each R(-) observed was independent of analyte type (e.g., whether the analyte was aliphatic or aromatic, or possessed certain functional groups).

  18. Characterization of bonding between poly(dimethylsiloxane) and cyclic olefin copolymer using corona discharge induced grafting polymerization.

    Science.gov (United States)

    Liu, Ke; Gu, Pan; Hamaker, Kiri; Fan, Z Hugh

    2012-01-01

    Thermoplastics have been increasingly used for fabricating microfluidic devices because of their low cost, mechanical/biocompatible attributes, and well-established manufacturing processes. However, there is sometimes a need to integrate such a device with components made from other materials such as polydimethylsiloxane (PDMS). Bonding thermoplastics with PDMS to produce hybrid devices is not straightforward. We have reported our method to modify the surface property of a cyclic olefin copolymer (COC) substrate by using corona discharge and grafting polymerization of 3-(trimethoxysilyl)propyl methacrylate; the modified surface enabled strong bonding of COC with PDMS. In this paper, we report our studies on the surface modification mechanism using attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and contact angle measurement. Using this bonding method, we fabricated a three-layer (COC/PDMS/COC) hybrid device consisting of elastomer-based valve arrays. The microvalve operation was confirmed through the displacement of a dye solution in a fluidic channel when the elastomer membrane was pneumatically actuated. Valve-enabled microfluidic handling was demonstrated.

  19. Line broadening of excimers bound to the surface of 4He clusters investigated by comparison with corona discharge excitation spectra

    Science.gov (United States)

    Mendoza-Luna, Luis Guillermo; Watkins, Mark; von Haeften, Klaus; Bonifaci, Nelly; Aitken, Frederic

    2013-06-01

    A new method for assessing the site-specific emission from electronically excited helium droplets is presented. The fluorescence features of helium droplets show sharp rotationally resolved lines indicating desorption of excimers and emission far outside the droplets as well as blue-shifted and strongly broadened features due to emission of excimers confined in cavities within the droplets. A third feature is identified: slightly broadened rotational lines that we attribute to emission from excimers bound to the droplet surface. The line broadening arises from collisions with the helium gas within the surface layer of the helium droplets. These conditions are simulated using a high pressure gas cell in which helium gas is electronically excited using a corona discharge. Rotational line broadening of similar magnitude to that of large droplets (N ˜ 107 atoms) is observed for gas pressures at about 5 bar and 80 K, corresponding to a number density of 4.52 × 10-4 Å-3. We conclude that the excimers are located within a shell separated by 6 to 7 Å from the radius where the density has dropped to 50% of its centre value. Helium droplets that are smaller (N ˜ 104 atoms) exhibit rotational lines that are less broadened, which we attribute to the superposition of features originating from desorbed and from surface-bound excimers. A fit of the linewidths reveals that around 50% of the excimers are bound to the surface of the smaller droplets.

  20. Measurement of OH (X2Σ) in immediate vicinity of dielectric surface under pulsed dielectric barrier discharge at atmospheric pressure using two geometries of laser-induced fluorescence

    Science.gov (United States)

    Teramoto, Yoshiyuki; Kim, Hyun-Ha; Ogata, Atsushi; Negishi, Nobuaki

    2014-04-01

    The behavior of the ground state OH radical was studied in humid air using pulsed surface dielectric barrier discharge. The validity of OH measurement in immediate vicinity of the dielectric surface was discussed using two geometries of laser-induced fluorescence (LIF) measurement, and surface distribution and temporal profiles of OH were examined. A comparison of parallel- and perpendicular-LIF techniques for OH measurement revealed that OH was mostly produced in a region several tens of μm above the dielectric surface. The surface distribution profile of OH agreed well with that of N2(C), and in both cases, the total production generated by a discharge pulse was proportional to the discharge energy. The OH local density in surface streamer channels was estimated to be 1.3 × 1015 cm-3 according to the decay rate of OH, which was similar to that in corona discharge. Additionally, the local density of OH remained constant regardless of discharge energies. These results indicate that the yield of OH increased with the discharge energy owing to expansion of the surface streamer region, increase in streamer radius or thickness or the number of branches, whereas the local density of OH in the streamer channel remained constant regardless of discharge energy.

  1. Nanoparticle formation in H2O/N-2 and H2O/Ar mixtures under irradiation by 20 MeV protons and positive corona discharge

    DEFF Research Database (Denmark)

    Imanaka, M.; Tomita, S.; Kanda, S.

    2010-01-01

    To investigate the contribution of ions to gas nucleation, we have performed experiments on the formation of water droplets in H2O/N-2 and H2O/Ar gas mixtures by irradiation with a 20 MeV proton beam and by positive corona discharge. The size of the formed nanoparticles was measured using a diffe...... positive and negative ions for the formation of nanosize droplets, which attract each other by Coulomb interactions, enhancing the collision frequency and leading to the formation of the 10 nm droplets.......To investigate the contribution of ions to gas nucleation, we have performed experiments on the formation of water droplets in H2O/N-2 and H2O/Ar gas mixtures by irradiation with a 20 MeV proton beam and by positive corona discharge. The size of the formed nanoparticles was measured using...... a differential mobility analyzer equipped with a Faraday cup electrometer. Using the proton beam, droplets around 10 nm in diameter were observed for both positively and negatively charged particles, but none were found when the corona discharge was used. This implies the importance of the presence of both...

  2. Volume Diffuse Dielectric Barrier Discharge Plasma Produced by Nanosecond High Voltage Pulse in Airflow

    Institute of Scientific and Technical Information of China (English)

    QI Haicheng; GAO Wei; FAN Zhihui; LIU Yidi; REN Chunsheng

    2016-01-01

    Volume diffuse dielectric barrier discharge (DBD) plasma is produced in subsonic airflow by nanosecond high-voltage pulse power supply with a plate-to-plate discharge cell at 6 mm air gap length.The discharge images,optical emission spectra (OES),the applied voltage and current waveforms of the discharge at the changed airflow rates are obtained.When airflow rate is increased,the transition of the discharge mode and the variations of discharge intensity,breakdown characteristics and the temperature of the discharge plasma are investigated.The results show that the discharge becomes more diffuse,discharge intensity is decreased accompanied by the increased breakdown voltage and time lag,and the temperature of the discharge plasma reduces when airflow of small vclocity is introduced into the discharge gap.These phenomena are because that the airflow changes the spatial distribution of the heat and the space charge in the discharge gap.

  3. Volume Diffuse Dielectric Barrier Discharge Plasma Produced by Nanosecond High Voltage Pulse in Airflow

    Science.gov (United States)

    Qi, Haicheng; Gao, Wei; Fan, Zhihui; Liu, Yidi; Ren, Chunsheng

    2016-05-01

    Volume diffuse dielectric barrier discharge (DBD) plasma is produced in subsonic airflow by nanosecond high-voltage pulse power supply with a plate-to-plate discharge cell at 6 mm air gap length. The discharge images, optical emission spectra (OES), the applied voltage and current waveforms of the discharge at the changed airflow rates are obtained. When airflow rate is increased, the transition of the discharge mode and the variations of discharge intensity, breakdown characteristics and the temperature of the discharge plasma are investigated. The results show that the discharge becomes more diffuse, discharge intensity is decreased accompanied by the increased breakdown voltage and time lag, and the temperature of the discharge plasma reduces when airflow of small velocity is introduced into the discharge gap. These phenomena are because that the airflow changes the spatial distribution of the heat and the space charge in the discharge gap. supported by National Natural Science Foundation of China (No. 51437002)

  4. 电晕场处理三层水稻种子对其活力的影响%Effect of corona discharge field processing on vigor of three layers of paddy seeds

    Institute of Scientific and Technical Information of China (English)

    徐江; 郭守志; 贾国梁; 张宁; 宋占华; 许光虎; 张春庆; 李法德

    2015-01-01

    为提高电晕场处理水稻种子的效率,该文利用弧形芒刺电极阵列与平板电极构建了正脉冲电晕电场,研究了电晕场对铺放在平板电极上的3层水稻种子活力的影响。试验结果显示,在相同的处理时间(4 min)和电压(18、20和22 kV)条件下,脉冲电晕场对不同位置的种子有不同的影响:18 kV(root mean square, RMS)处理3层水稻种子时,上层种子的活力指标较对照有显著的提高(P<0.01或0.05),中层和下层种子较对照无明显差别;20 kV(RMS)处理3层水稻种子时,上、中、下3层种子的活力指标较对照有显著的提高(P<0.01或0.05),层与层之间不存在显著差异;22 kV(RMS)处理3层水稻种子时,除发芽势外下层种子的其余活力指标较对照有显著提高(P<0.01或0.05),上层和中层种子较对照无明显差别。并且,18 kV处理时的上层种子、20 kV处理时的所有种子和22 kV处理时的中层和下层种子的发芽数峰值较对照组均提前1 d,这与活力指标的提高是一致的。试验结果表明,利用电晕场处理多层种子以提高其活力指标是可行的,但电晕场所释放的电磁能必须在适当范围内,即利用电晕场处理种子时,电场处理条件(电场强度与处理时间)必须在优化范围内。脉冲电晕场能够提高种子活力,其机理可能是脉冲电晕场在种子内部引起的脉冲极化力使得种子内部细胞膜重新排列,但这有待于进一步研究。%In order to increase the efficiency of a corona discharge field processing aged paddy seeds, a positive pulse corona discharged field consisting of an arc-shaped prick electrode array and a plate electrode (as the grounding electrode) was developed in this research. The gap between the arc-shaped electrode array and the plate was 50 mm. After adjusted with an AC transformer and converted into the positive pulse DC voltage

  5. Holistic Investigation of Corona Discharge: Impulse Current Waveform and Phase-resolved Measurement, Analysis and Simulation%Holistic Investigation of Corona Discharge: Impulse Current Waveform and Phase-resolved Measurement, Analysis and Simulation

    Institute of Scientific and Technical Information of China (English)

    Suwarno

    2011-01-01

    Partial discharge(PD) is one of the most important phenomenon in high voltage insulations. In most cases, the appearance of partial discharges is related to insulation defects. Understanding partial discharges is important for diagnosis on insulation condition. Corona discharges appear when extremely high electric field appears on the conductor surface exceeding the electric field strength of the gas. The high electric field may occur at around protrusion with very sharp tip. This paper reported a holistic approach of corona discharge investigation. The needle--plane electrode system was used. The medium between the electrodes was air. The needle was made from steel with radius of curvature of 3 μm (Ogura needle). Sinusoidal as well as triangular applied voltages were used. The waveform of the corona discharges was measured using a digital oscilloscope. The corona discharge pulses were measured using a phase--re- solved PD measurement system. The system was able to measure the magnitude (q) and phase angle position (9) of each PD pulses, as well as the number of discharge pulses (n). The role of applied voltage was investigated using phase--resolved analysis of corona discharge pulses through pulse sequence, pulse magnitude and pulse number analy- sis. Experimental results indicated that corona discharge current waveform was an impulse with rise time of about several ns and the impulse width of about 100 ns. The Fast Fourier Transform analysis indicated that the corona discharge current waveform had several spectrum peaks at frequency of 7.8 MHz, 85.9 MHz, 109.4 MHz and 195.3 MHz. The experimental results also showed that discharge pulses were concentrated around the peak of applied voltage for both sinusoidal and triangular voltages. The discharge magnitude, as well as its probability of occurrence, was strongly dependent on the instantaneous applied voltage. The shape of φn, as well as φ-q-n PD patterns, were strongly reflected by the shape

  6. Research on Corona Layer of Needle-plate Discharge in Atmosphere%大气中针板放电电晕层的研究

    Institute of Scientific and Technical Information of China (English)

    刘志强; 刘铁; 苗欣宇; 郭威

    2013-01-01

    In the experimet the images of needle-plate corona discharge are obtained. The gray value and thickness of corona layer was measured by reading luminescence data using photoshop software. The result shows that corona luminous intensity is relatively uniform after corona. With the discharge voltage increasing, a bright and uneven area is created in the tip place. With the increase of needlepoint distance, luminous intensity initially decreased slowly, following diminished rapidly and finally declined slowly. When corona area appeared luminous at different points, its intensity approximate linearly increases with the increase of the voltage. The thickness of corona layer rapidly grew, then there would be a stable region, with the increase of voltage, thickness of corona layer developed from flat to ascending.%通过对针板电晕放电实验,得到发光图像,并针对发光图像,描述了电晕层形貌.利用photoshop软件读取发光照片数据,测量出电晕层的灰度值和厚度.结果表明,在放电起晕后电晕发光强度在层内相对均匀,随着放电电压增大,在针尖处会产生一个明亮而不均匀的区域.发光强度随距针尖距离的变化规律为首先缓慢减小,然后迅速减小,最后又变得缓慢减小.当电晕区不同定点出现发光后,其发光强度随电压的增大表现出近似线性增强的趋势.起晕后电晕层厚度快速增长,随后会出现一个稳定区,当电压继续增大,电晕层厚度由平直向上升发展.

  7. Characterisation of Partial Discharge Pulses in Artificial Voids in Polypropylene Films Used in Capacitors

    OpenAIRE

    B. Ramachandra; Nema, RS

    1996-01-01

    Partial discharges in voids may cause deterioration of solid insulating materials. They often start in voids enclosed in insulation and or at the interface defects. A method of measuring fast discharge pulses with rise times below 1 ns is reported. Characterisation of partial discharge pulses in artificial voids in polypropylene films at atmospheric pressure is analysed that incorporates inception voltage, apparent and real charge, drift velocity and mobility of electrons.

  8. Electron density and electron temperature measurements in nanosecond pulse discharges over liquid water surface

    Science.gov (United States)

    Simeni Simeni, M.; Roettgen, A.; Petrishchev, V.; Frederickson, K.; Adamovich, I. V.

    2016-12-01

    Time-resolved electron density, electron temperature, and gas temperature in nanosecond pulse discharges in helium and O2-He mixtures near liquid water surface are measured using Thomson/pure rotational Raman scattering, in two different geometries, (a) ‘diffuse filament’ discharge between a spherical high-voltage electrode and a grounded pin electrode placed in a reservoir filled with distilled water, with the tip exposed, and (b) dielectric barrier discharge between the high-voltage electrode and the liquid water surface. A diffuse plasma filament generated between the electrodes in helium during the primary discharge pulse exhibits noticeable constriction during the secondary discharge pulse several hundred ns later. Adding oxygen to the mixture reduces the plasma filament diameter and enhances constriction during the secondary pulse. In the dielectric barrier discharge, diffuse volumetric plasma occupies nearly the entire space between the high voltage electrode and the liquid surface, and extends radially along the surface. In the filament discharge in helium, adding water to the container results in considerable reduction of plasma lifetime compared to the discharge in dry helium, by about an order of magnitude, indicating rapid electron recombination with water cluster ions. Peak electron density during the pulse is also reduced, by about a factor of two, likely due to dissociative attachment to water vapor during the discharge pulse. These trends become more pronounced as oxygen is added to the mixture, which increases net rate of dissociative attachment. Gas temperature during the primary discharge pulse remains near room temperature, after which it increases up to T ~ 500 K over 5 µs and decays back to near room temperature before the next discharge pulse several tens of ms later. As expected, electron density and electron temperature in diffuse DBD plasmas are considerably lower compared to peak values in the filament discharge. Use of Thomson

  9. Using short pulses to enhance the production rate of vibrationally excited hydrogen molecules in hydrogen discharge

    Institute of Scientific and Technical Information of China (English)

    Sun Ji-Zhong; Li Xian-Tao; Bai Jing; Wang De-Zhen

    2012-01-01

    Hydrogen discharges driven by the combined radio-frequency(rf)/short pulse sources are investigated using the particle-in-cell method.The simulation results show that the discharge driven additionally by the short pulse can enhance the electron density and modulate the electron energy to provide a better condition for negative hydrogen ion production than the discharge driven by the rf-only source.

  10. Pulse Operation of Chemical Oxygen-Iodine Laser by Pulsed Gas Discharge with the Assistance of Spark Pre-ionization

    Institute of Scientific and Technical Information of China (English)

    LI Guo-Fu; YU Hai-Jun; DUO Li-Ping; JIN Yu-Qi; WANG Jian; SANG Feng-Ting; FANG Ben-Jie; WANG De-Zhen

    2009-01-01

    The continuous wavelength chemical oxygen-iodine laser can be turned into pulse operation mode in order to obtain high energy and high pulse power. We propose an approach to produce iodine atoms instantaneously by pulsed gas discharge with the assistance of spark pre-ionization to achieve the pulsed goal. The influence of spark pre-ionization on discharge homogeneity is discussed. Voltage-current characteristics are shown and discussed in existence of the pre-ionization capacitor and peaking capacitor. The spark pre-ionization and peaking capacitor are very helpful in obtaining a stable and homogeneous discharge. The lasing is achieved at the total pressure of 2.2-2.9 kPa and single pulse energy is up to 180m J, the corresponding specific output energy is 1.0 J/L.

  11. Electrical and mechanical characteristics of nanosecond pulsed sliding dielectric barrier discharges with different electrode gaps

    Science.gov (United States)

    Bayoda, K. D.; Benard, N.; Moreau, E.

    2015-10-01

    This study proposes the characterization of a surface sliding discharge that extends over a length of 80 mm. The gas ionization is caused by series of high voltage pulses with nanosecond rising and decaying times while ion drift is forced by a negative DC component. Different plasma diagnostics such as electrical measurements, iCCD visualizations and strioscopy have been performed. They highlight that a threshold mean electric field between both air-exposed electrodes is required to fully establish a sliding discharge. Compared to a single nanosecond pulsed dielectric barrier discharge, the sliding discharge results in an energy consumption increase. Moreover, the pressure wave induced by the discharge is strongly impacted.

  12. Flow Reactor Studies with Nanosecond Pulsed Discharges at Atmospheric Pressure and Higher

    Science.gov (United States)

    2013-10-01

    Image of Discharge Reactor with Viewport Inlet Cap • Modular plasma discharge reactor can be interchanged with redesigned pressure shell to perform...Flow Reactor Studies with Nanosecond Pulsed Discharges at Atmospheric Pressure and Higher Nicholas Tsolas, Kuni Togai and Richard Yetter...Department of Mechanical and Nuclear Engineering The Pennsylvania State University University Park, PA, 16801 Fourth Annual Review Meeting of the

  13. Pulsed Discharge Helium Ionization Detector for Highly Sensitive Aquametry.

    Science.gov (United States)

    Mowry, Curtis D; Pimentel, Adam S; Sparks, Elizabeth S; Moorman, Matthew W; Achyuthan, Komandoor E; Manginell, Ronald P

    2016-01-01

    Trace moisture quantitation is crucial in medical, civilian and military applications. Current aquametry technologies are limited by the sample volume, reactivity, or interferences, and/or instrument size, weight, power, cost, and complexity. We report for the first time on the use of a pulsed discharge helium ionization detector (PDHID-D2) (∼196 cm(3)) for the sensitive (limit of detection, 0.047 ng; 26 ppm), linear (r(2) >0.99), and rapid (volume of liquid or gas. The relative humidity sensitivity was 0.22% (61.4 ppmv) with a limit of detection of less than 1 ng moisture with gaseous samples. The sensitivity was 10 to 100 to fold superior to competing technologies without the disadvantages inherent to these technologies. The PDHID-D2, due to its small footprint and low power requirement, has good size, weight, and power-portability (SWAPP) factors. The relatively low cost (∼$5000) and commercial availability of the PDHID-D2 makes our technique applicable to highly sensitive aquametry.

  14. Corona helps curb losses

    Energy Technology Data Exchange (ETDEWEB)

    Laasonen, M.; Lahtinen, M.; Lustre, L.

    1996-11-01

    The greatest power losses in electricity transmission arise through a phenomenon called load losses. Corona losses caused by the surface discharge of electricity also constitute a considerable cost item. IVS, the nationwide network company, is investigating corona- induced losses, and has also commissioned similar research from IVO International, the Technical Research Centre of Finland (VTT) and from Tampere University of Technology. The research work strives to gain more in-depth knowledge on the phenomenon of frosting and its impact on corona losses. The correct prediction of frost helps reduce corona losses, while also cutting costs considerably. (orig.)

  15. Corona helps curb losses

    Energy Technology Data Exchange (ETDEWEB)

    Laasonen, M.; Lahtinen, M.; Lustre, L.

    1996-11-01

    The greatest power losses in electricity transmission arise through a phenomenon called load losses. Corona losses caused by the surface discharge of electricity also constitute a considerable cost item. IVS, the nationwide network company, is investigating corona- induced losses, and has also commissioned similar research from IVO International, the Technical Research Centre of Finland (VTT) and from Tampere University of Technology. The research work strives to gain more in-depth knowledge on the phenomenon of frosting and its impact on corona losses. The correct prediction of frost helps reduce corona losses, while also cutting costs considerably. (orig.)

  16. Synergistic Decolouration of Azo Dye by Pulsed Streamer Discharge Immobilized TiO2 Photocatalysis

    Institute of Scientific and Technical Information of China (English)

    LI Jie; WANG Huijuan; LI Guofeng; WU Yan; QUAN Xie; LIU Zhigang

    2007-01-01

    Photocatalyst was prepared by immobilizing TiO2 on glass beads using the traditional sol-gel method.Ultraviolet light(UV)produced by pulsed streamer discharge Was then used to induce photocatalytic activity of TiO2 photocatalyst.Decolouration efficiency of the representative azo dye(acid orange 7,AO7)was investigated using the synergistic system of pulsed streamer discharge plasma and TiO2 photocatalysis.The obtained results showed that the decolouration rate of AO7 could be increased by 16.7% under the condition of adding supported TiO2 in the pulsed streamer discharge system,compared to that in the sole pulsed streamer discharge plasma system,due to the synergistic effect of pulsed streamer discharge and TiO2 photocatalysis induced by pulsed streamer discharge.The synergistic system of pulsed streamer discharge and TiO2 photocatalyst Was found to have more reactive radicals for degradation of organic compounds in Water.

  17. Collision-Induced Dissociation Study of the Adduct Ions Produced in NO3 (-)-Free Area of Atmospheric Pressure Negative Corona Discharges under Ambient Air Conditions.

    Science.gov (United States)

    Sekimoto, Kanako; Matsuda, Natsuki; Takayama, Mitsuo

    2013-01-01

    Collision-induced dissociation (CID) experiments of adducts [M+R](-) with negative atmospheric ions R(-) (O2 (-), HCO3 (-) and COO(-)(COOH)) produced in NO3 (-)-free discharge area in atmospheric pressure corona discharge ionization (APCDI) method were performed using aliphatic and aromatic compounds M. The [M+R](-) adducts for individual R(-) fragmented to form deprotonated analytes [M-H](-) as well as the specific product ions which also occurred in the CID of [M-H](-), independent of analytes with several different functional groups. The results obtained suggested that the specific product ions formed in the CID of [M+R](-), as well as CID of [M-H](-), are generated due to further fragmentation of the product ions [M-H](-). It was concluded, therefore, that CID of [M+R](-) formed in NO3 (-)-free discharge area can indirectly lead to the formation of the product ions originating from [M-H](-).

  18. Comparison of atmospheric air plasmas excited by high-voltage nanosecond pulsed discharge and sinusoidal alternating current discharge

    Science.gov (United States)

    Zhang, Shuai; Wang, Wen-chun; Jiang, Peng-chao; Yang, De-zheng; Jia, Li; Wang, Sen

    2013-10-01

    In this paper, atmospheric pressure air discharge plasma in quartz tube is excited by 15 ns high-voltage nanosecond pulsed discharge (HVNPD) and sinusoidal alternating current discharge (SACD), respectively, and a comparison study of these two kinds of discharges is made through visual imaging, electrical characterization, optical detection of active species, and plasma gas temperature. The peak voltage of the power supplies is kept at 16 kV while the pulse repetition rate of nanosecond pulse power supply is 100 Hz, and the frequency of sinusoidal power supply is 10 kHz. Results show that the HVNPD is uniform while the SACD presents filamentary mode. For exciting the same cycles of discharge, the average energy consumption in HVNPD is about 1/13 of the SACD. However, the chemical active species generated by the HVNPD is about 2-9 times than that excited by the SACD. Meanwhile, the rotational and vibrational temperatures have been obtained via fitting the simulated spectrum of N2 (C3Πu → B3Πg, 0-2) with the measured one, and the results show that the plasma gas temperature in the HVNPD remains close to room temperature whereas the plasma gas temperature in the SACD is about 200 K higher than that in HVNPD in the initial phase and continually increases as discharge exposure time goes on.

  19. 大气压直流正电晕放电暂态空间电荷分布仿真研究%Numerical simulation of transient space charge distribution of DC positive corona discharge under atmospheric pressure air

    Institute of Scientific and Technical Information of China (English)

    廖瑞金; 伍飞飞; 刘兴华; 杨帆; 杨丽君; 周之; 翟蕾

    2012-01-01

    DC positive corona discharge under atmospheric environment. The model is based on the plasma hydrodynamics and the chemical dynamics, and it includes 12 species and 27 reactions. Besides, the photoionization effect is also considered in the proposed model. The simulation and the experiment on bar-plate electrode configuration with an inter-electrode gap of 5.0 mm at 2-5.5 kV are carried out. The discharge voltage-current characteristics and single pulse waveform are in good agreement with the experimental measurements. Based on this model, the electric field distribution, the electron temperature distribution, and the evolution of charged species distribution are investigated in detail. The results show that distributions of electron temperature and electric field have the same patterns, In the process of discharge, electron density is kept at 10^19 m-3 or so. O4+ is dominant compared with the other charged heavy species, and O+ and N+ play the key role in secondary electron emission: the unmbers of O~ and O are the largest in negative ions and neutral particle respectively, they play a negligible role in discharge process.

  20. The Effects of Corona on Current Surges Induced on Conducting Lines by EMP (Electromagnetic Pulse): A Comparison of Experiment Data with Results of Analytic Corona Models

    Science.gov (United States)

    1987-09-01

    265-281. 18. Rogers , S.R., and R.A. Perala, "The Effects of Corona and Angle of Arrival on the EMP Response of Cables Lying on the Surface of the...Survivability Organization, Boeing Aerospace COmpany, P. 0. Box 399, Seattle, WA 98124 74. V. L. Chartier , Bonneville Power Administration, P. 0. Box

  1. Experimental studies of the formation of cluster ions formed by corona discharge in an atmosphere containing SO2, NH3, and H2O

    DEFF Research Database (Denmark)

    Hvelplund, Preben; Pedersen, Jens Olaf Pepke; Støchkel, Kristian

    2013-01-01

    Abstract We report on studies of ion-induced nucleation in a corona discharge taking place in an atmosphere containing SO2, NH3, and H2O at standard temperature and pressure. Positive ions such as H3O+(H2O)n, NH4+(H2O)n, and H+(H2SO4)(H2O)n and negative ions such as HSO5-(H2O)n, SO4-(H2O)n, HSO4-(H...

  2. Experimental Investigation of Pulsed Nanosecond Streamer Discharges for CO2 Reforming

    Science.gov (United States)

    Pachuilo, Michael; Levko, Dima; Raja, Laxminarayan; Varghese, Philip

    2016-09-01

    Rapid global industrialization has led to an increase in atmospheric greenhouse gases, specifically carbon dioxide levels. Plasmas present a great potential for efficient reforming of greenhouse gases. There are several plasma discharges which have been reported for reforming process: dielectric barrier discharges (DBD), microwave discharges, and glide-arcs. Microwave discharges have CO2 conversion energy efficiency of up to 40% at atmospheric conditions, while glide-arcs have 43% and DBD 2-10%. In our study, we analyze a single nanosecond pulsed cathode directed streamer discharge in CO2 at atmospheric pressure and temperature. We have conducted time resolved imaging with spectral bandpass filters of a streamer discharge with an applied negative polarity pulse. The image sequences have been correlated to the applied voltage and current pulses. From the spectral filters we can determine where spatially and temporally excited species are formed. In this talk we report on spectroscopic studies of the discharge and estimate plasma properties such as temperature and density of excited species and electrons. Furthermore, we report on the effects of pulse polarity as well as anodic streamer discharges on the CO2 conversion efficiency. Finally, we will focus on the effects of vibrational excitation on carbon dioxide reforming efficiency for streamer discharges. Our experimental results will be compared with an accompanying plasma computational model studies.

  3. RAPID COMMUNICATION: Enhanced performance of a dielectric barrier discharge lamp using short-pulsed excitation

    Science.gov (United States)

    Mildren, R. P.; Carman, R. J.

    2001-01-01

    We observe marked increases in the time-averaged intensity, peak intensity, efficiency and spectral purity of the VUV output from an Xe excimer barrier discharge lamp when using short-pulse (~150 ns FWHM (full width half maximum)) excitation. Intensity increases with Xe pressure up to 600 Torr with a maximum output 2.6 times higher and an efficiency 3.2 times higher than the same lamp excited by conventional ac excitation (i.e. sinusoidal voltage waveform). The output occurs in regular short pulses (pulsed discharge appears diffuse (i.e. glow-like), even at the higher pressures at which the ac discharge is filamentary. It is concluded that the enhanced performance results largely from the ability for pulsed excitation to generate a discharge at near atmospheric pressures with a much lower electron density than that possible using ac.

  4. Self-consistent spatio-temporal simulation of pulsed microwave discharge

    Energy Technology Data Exchange (ETDEWEB)

    Bonaventura, Z; Trunec, D; Mesko, M; Vasina, P; Kudrle, V [Department of Physical Electronics, Faculty of Science, Masaryk University, Kotlarska 2, 611 37 Brno (Czech Republic)

    2008-01-07

    A spatio-temporal theoretical model of pulsed microwave discharge was developed. This model is based on the macroscopic continuity equation for electrons and on the wave equation for an electromagnetic wave passing through the discharge plasma. These equations were solved together and in a self-consistent manner. For simplicity, the continuity equation was solved in one dimension only and the electromagnetic wave was assumed to be plane and transversal. Both equations were solved numerically and the spatio-temporal dependences of electron concentration and the amplitude of the microwave electric field were obtained. It was found that the discharge development depends, significantly, on the initial spatial distribution of electron concentration. Two different cases were studied: the discharge development during the first microwave pulse only and after several successive pulses. The calculations were performed particularly for the discharge in nitrogen. The results were compared with experimental data from our previous work.

  5. Behavior of 2 Cell CPV NI-H2 Battery During Pulse Discharge

    Science.gov (United States)

    Gopalakrishna, M. Rao; Vaidyanathan, Hari

    1997-01-01

    A study was carried out to determine the transient voltage behavior of the 2-cell CPV nickel-hydrogen battery with the objective of using the results as a basis for mathematical modeling. The 2-cell CPV battery which is manufactured by Eagle Picher, Inc. for the GOES program yields 18.5 Ah at C/2 rate of discharge at 10 C with a mid-discharge voltage of 2.514 V. The capacity increased with decrease of temperature and a maximum capacity of 22 Ah was obtained at - 5 C. The pulse test consisted of obtaining the voltage profile in the first 20 milliseconds of the one minute pulse discharge at 37 A and pulse discharge was repeated as a function of state-of-charge. The pulse test at 10 C and 20 C provided voltage profiles with the expected decrease in voltage as the pulse was applied. The end of pulse voltage decreased with the state-of-charge. The battery voltage was above 2V at the end of the one-minute pulse at 12% state-of-charge at 10 C. The voltage profile during the 37 A pulse discharge consists of an initial drop in voltage which was independent of the state of charge. The invariability in the value for the initial drop in voltage with state of charge is a very important observation and indicates that towards the end of discharge the dominant resistance is not ohmic in nature. It could be hypothesized from the nature of the voltage transients that the dominant mechanism towards the end of discharge is proton diffusion. The study also shows that the dominant resistance in the voltage plateau during discharge is activation polarization.

  6. Behavior of 2-Cell CPV Ni-H2 Battery During Pulse Discharge

    Science.gov (United States)

    Vaidyanathan, Hari; Rao, Gopalakrishna

    1998-01-01

    A study was carried out to determine the transient voltage behavior of the 2-cell CPV nickel-hydrogen battery with the objective of using the results as a basis for mathematical modeling. The 2-cell CPV battery which is manufactured by Eagle Picher, Inc. for the GOES program yields 18.5 Ah at C/2 rate of discharge at 10 C with a mid-discharge voltage of 2.514 V. The capacity increased with decrease of temperature and a maximum capacity of 22 Ah was obtained at -5 C. The pulse tests consisted of obtaining the voltage profile in the first 20 milliseconds of the one minute pulse discharge at 37 A and pulse discharge was repeated as a function of state-of-charge. The pulse test at 10 C and 20 C provided voltage profiles with the expected decrease in voltage as the pulse was applied. The end of pulse voltage decreased with the state-of-charge. The battery voltage was above 2V at the end of the one-minute pulse at 8 % state-of-charge at 10 C. The voltage profile during the 37 A pulse discharge consists of an initial drop in voltage which was independent of the state of charge. The invariability in the value for the initial drop in voltage with state of charge is a very important observation. The results show that towards the end of discharge the dominant resistance is not ohmic in nature. It could be hypothesized from the nature of the voltage transients that the dominant mechanism towards the end of discharge is proton diffusion. The study also shows that the dominant resistance in the voltage plateau during discharge is activation polarization.

  7. PULSED CAPILLARY DISCHARGE CHARACTERIZATION FOR SOFT X-RAY MICROSCOPY APPLICATIONS

    OpenAIRE

    VALDIVIA LEIVA; MARIA PIA

    2011-01-01

    The hollow cathode capillary discharge is of great interest as a high brightness, short pulse soft x-ray source. This thesis presents work done in the development, modifications, and subsequent characterization of a compact plasma source comprised of a pulsed capillary discharge exploiting hollow cathode dynamics. The low inductance, low stored energy, source is optimized using optical, electrical, x-ray, and e-beam diagnostics. The effect of parameters on the capillary phys...

  8. Operation Mode on Pulse Modulation in Atmospheric Radio Frequency Glow Discharges

    Science.gov (United States)

    Zhang, Jie; Guo, Ying; Huang, Xiaojiang; Zhang, Jing; Shi, Jianjun

    2016-10-01

    The discharge operation regime of pulse modulated atmospheric radio frequency (RF) glow discharge in helium is investigated on the duty cycle and frequency of modulation pulses. The characteristics of radio frequency discharge burst in terms of breakdown voltage, alpha(α)-gamma(γ) mode transition voltage and current are demonstrated by the discharge current voltage characteristics. The minimum breakdown voltage of RF discharge burst was obtained at the duty cycle of 20% and frequency of 400 kHz, respectively. The α-γ mode transition of RF discharge burst occurs at higher voltage and current by reducing the duty cycle and elevating the modulation frequency before the RF discharge burst evolving into the ignition phase, in which the RF discharge burst can operate stably in the γ mode. It proposes that the intensity and stability of RF discharge burst can be improved by manipulating the duty cycle and modulation frequency in pulse modulated atmospheric RF glow discharge. supported by National Natural Science Foundation of China (Nos. 11475043 and 11375042)

  9. Application of dimensional analysis to ozone production by pulsed streamer discharge in oxygen

    CERN Document Server

    Buntat, Z; Smith, I R

    2003-01-01

    This paper describes the use of dimensional analysis in investigating the effects of the electrical and the discharge configuration parameters on ozone production in oxygen, by means of a pulsed streamer discharge. Ozone destruction factors are taken into account in the model, and predicted results are shown to be in good agreement with experimental findings.

  10. Modeling of asymmetric pulsed phenomena in dielectric-barrier atmospheric-pressure glow discharges

    Energy Technology Data Exchange (ETDEWEB)

    Ha Yan [College of Mathematics and Computer Science, Hebei University, Baoding 071002 (China); Wang Huijuan [School of Mathematics and Physics, North China Electric Power University, Baoding 071003 (China); Wang Xiaofei [College of Physics Science and Technology, Hebei University, Baoding 071002 (China)

    2012-01-15

    Asymmetric current pulses in dielectric-barrier atmospheric-pressure glow discharges are investigated by a self-consistent, one-dimensional fluid model. It is found that the glow mode and Townsend mode can coexist in the asymmetric discharge even though the gas gap is rather large. The reason for this phenomenon is that the residual space charge plays the role of anode and reduces the gap width, resulting in the formation of a Townsend discharge.

  11. Initiation of ignition by the action of a high-current pulsed discharge on a gas

    NARCIS (Netherlands)

    Starikovskii, AY

    2003-01-01

    The possibility of nonthermal initiation of chemical reactions by a uniform pulsed nanosecond discharge is demonstrated. Dependences of variation of the ignition delay on initial conditions are obtained. It is shown that the main role in combustion initiation under conditions of a pulsed gas dischar

  12. 流光电晕放电净化粗燃气焦油及粉尘研究进展%An Overview of Tar and Dust Removal from Biomass-Derived Syngas by Streamer Corona Discharges

    Institute of Scientific and Technical Information of China (English)

    谢建军; 徐彬; 阴秀丽; 吴创之; 闫克平

    2016-01-01

    A high-efficiency method of tar and dust removal from fuel gas is of great significance to the development of biomass gasification. Streamer corona discharges, which can not only effectively crack the heavy organics to light molecules in raw syngas in reaction with O, H, OH radicals but also charge and separate the dust from the raw syngas with pulsed coronas, is a promising method for raw syngas cleaning. In this paper the status of tar and dust removal by streamer corona discharges were reviewed; issues on mechanism of tar cracking and dust abatement,current situation, key scientific and technical problems of the tar and dust removal from the biomass-derived syngas were analyzed. A conceptual design of an electrocyclone plasma reactor for simultaneous tar and dust removal was proposed. Finally, for the purpose of solving the problems of raw syngas cleaning during biomass gasification, several key research areas were briefly addressed.%研究焦油及粉尘的高效净化方法对推动生物质气化技术的发展具有重要意义。流光电晕放电过程产生的O、H、OH 等活性自由基可有效裂解燃气中的焦油类有机物分子,在直流基压上叠加窄脉冲电压则可实现粉尘的荷电及高效气-固分离,是一种较有应用前景的粗燃气净化方法。笔者对流光电晕放电净化粗燃气焦油及粉尘的技术进展进行了综述,分析了该过程的裂解焦油/除尘机理、研究现状及关键科学问题,并提出了一种基于电旋风等离子体反应器的焦油及粉尘同时净化方法。最后针对生物质气化粗燃气净化过程中的瓶颈问题,简要归纳了其研究重点。

  13. Environmental and biotechnological applications of high-voltage pulsed discharges in water

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Masayuki [Department of Chemical and Environmental Engineering, Gunma University 1-5-1 Tenjin, Kiryu, Gunma 376-8515 (Japan)], E-mail: mxsato@cee.gunma-u.ac.jp

    2008-05-01

    A high-voltage pulse has wide application in fields such as chemistry, physics and biology and their combinations. The high-voltage pulse forms two kinds of physical processes in water, namely (a) a pulsed electric field (PEF) in the parallel electrode configuration and (b) plasma generation by a pulsed discharge in the water phase with a concentrated electric field. The PEF can be used for inactivation of bacteria in liquid foods as a non-thermal process, and the underwater plasma is applicable not only for the decomposition of organic materials in water but also for biological treatment of wastewater. These discharge states are controlled mainly by the applied pulse voltage and the electrode shape. Some examples of environmental and biotechnological applications of a high-voltage pulse are reviewed.

  14. The formation of diffuse discharge by short-front nanosecond voltage pulses and the modification of dielectrics in this discharge

    Science.gov (United States)

    Orlovskii, V. M.; Panarin, V. A.; Shulepov, M. A.

    2014-07-01

    The dynamics of diffuse discharge formation under the action of nanosecond voltage pulses with short fronts (below 1 ns) in the absence of a source of additional preionization and the influence of a dielectric film on this process have been studied. It is established that the diffuse discharge is induced by the avalanche multiplication of charge initiated by high-energy electrons and then maintained due to secondary breakdowns propagating via ionized gas channels. If a dielectric film (polyethylene, Lavsan, etc.) is placed on the anode, then multiply repeated discharge will lead to surface and bulk modification of the film material. Discharge-treated polyethylene film exhibits a change in the optical absorption spectrum in the near-IR range.

  15. Hypersonic Flow over a Cylinder with a Nanosecond Pulse Electrical Discharge

    Science.gov (United States)

    2014-03-01

    Hypersonic Flow over a Cylinder with a Nanosecond Pulse Electrical Discharge Nicholas J. Bisek∗ and Jonathan Poggie† U.S. Air Force Research...pulsed at nanosecond time scales and it rapidly added thermal energy to the flow, creating a shock wave that traveled away from the pulse source. As the...volumetric energy deposition model [14]. The approach was based on the assumption that the primary flow control mechanism of the ns-DBD is rapid thermal

  16. Negative hydrogen ion production in multicusp volume source with a pulsed discharge (abstract)a)

    Science.gov (United States)

    Bacal, M.; Belchenko, Yu. I.

    1996-03-01

    The pulsed operation of a negative ion volume source has been investigated, both with a magnetic filter present and without it, under conditions of full-scale acceleration of the extracted negative hydrogen ion beam. We report the observation of three afterglow negative ion peaks. As the negative ion current during the discharge pulse, each of the afterglow peaks can be optimized by varying the pressure, the plasma electrode bias and the extraction voltage. Under optimum conditions, the negative ion current during the discharge pulse exceeds the afterglow peaks.

  17. Spatial mask filtering algorithm for partial discharge pulse extraction of large generators

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A spatial mask filter algorithm (SMF) for partial discharge (PD) pulse extraction is proposed in this then direct multiplication of coefficients at two adjacent scales is used to detect singularity points of the signal tain the last spatial mask filter. By multiplication of wavelet coefficients with the final mask filter and wavelet reconstruction process, partial discharge pulses are extracted. The results of digital simulation and practical experiment show that this method is superior to traditional wavelet shrinkage method (TWS). This algorithm not only can increase the signal to noise ratio (SNR), but also can preserve the energy and pulse amplitude.

  18. VUV-VIS imaging of high-pressure pulsed discharge in argon

    Science.gov (United States)

    Treshchalov, Alexey B.; Lissovski, Alexander A.

    2008-01-01

    Spatial-time behavior of transversally excited pulsed volume discharge in argon is investigated by spontaneous emission spectroscopy and different imaging techniques. VUV Ar II* emission, UV-VIS continuum and Ar* red lines are used for direct monitoring of discharge homogeneity in the breakdown and recombination stages. Experimental data indicate that Ar* atoms and Ar II* excimers are created exclusively in the positive column of the discharge, not in near-cathode zones. These zones (cathode sheath and negative glow), however, are the main sources of UV-VIS continuum. The discharge is homogeneous during the first powerful breakdown pulse and fills the whole space between electrodes. Secondary excitation pulses initiate oscillations of plasma emission and longitudinal fragmentation of the discharge into separate zones. Fragmentation is connected with dynamical change of the electron emittance of heated and cold electrodes. Additional electrons, produced during secondary excitation pulses, convert effectively the reservoir of long-lived triplet Ar II* molecules to fast-emitted singlet Ar II* excimers - sharp spikes of VUV (126 nm) emission are observed. Double-pulse discharge pumping regime is suggested for easier achievement of the lasing threshold for rare gas excimer lasers.

  19. High voltage magnetic pulse generation using capacitor discharge technique

    Directory of Open Access Journals (Sweden)

    M. Rezal

    2014-12-01

    Full Text Available A high voltage magnetic pulse is designed by applying an electrical pulse to the coil. Capacitor banks are developed to generate the pulse current. Switching circuit consisting of Double Pole Double Throw (DPDT switches, thyristor, and triggering circuit is developed and tested. The coil current is measured using a Hall-effect current sensor. The magnetic pulse generated is measured and tabulated in a graph. Simulation using Finite Element Method Magnetics (FEMM is done to compare the results obtained between experiment and simulation. Results show that increasing the capacitance of the capacitor bank will increase the output voltage. This technology can be applied to areas such as medical equipment, measurement instrument, and military equipment.

  20. Numerical modeling of ozone production in a pulsed homogeneous discharge: A parameter study

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, J.O.; Eninger, J.E. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Industrial Electrotechnology

    1997-02-01

    The pulsed volume discharge is an alternative for the efficient generation of ozone in compact systems. This paper presents a parameter study of the reactions in this kind of homogeneous discharge by using a numerical model which solves plasma chemical kinetic rate and energy equations. Results are presented of ozone generation efficiency versus ozone concentration for different parameter combinations. Two parameter regimes are identified and analyzed. In the plasma phase ozone formation regime, where significant amounts of ozone are produced during the discharge pulse, it is found that higher ozone concentrations can be obtained than in the neutral phase ozone formation regime, where most of the ozone is formed after the discharge pulse. In the two-step ozone formation process, the rate of conversion of atomic oxygen plays a key role. In both regimes the ozone generation efficiency increases as n is increased or T{sub 0} decreased. The maximum concentration is 3% at 10 amagat and 100 K. The results on ozone accumulation in multiple pulse discharges are presented. In contrast to the single pulse case, higher efficiency is achieved at lower gas density. This scaling can be explained by losses due to ion currents. A tradeoff can be made between ozone generation efficiency and the number of pulses required to reach a certain concentration.

  1. Measurement of the impulse produced by a pulsed surface discharge actuator in air

    Science.gov (United States)

    Elias, P. Q.; Castera, P.

    2013-09-01

    The pulsed surface discharge in atmospheric pressure air generates a shock wave, thereby transferring an impulse to the surrounding gas. The aim of this work is to measure this impulse, using implementation of a plasma actuator based on linear surface discharges of length up to 10 cm, and of linear energy in a range 0.1-0.5 J cm-1. The shock wave generated by the discharge is visualized using a pulsed schlieren system and the impulse is measured with a dedicated balance. These measurements are correlated with 1D numerical simulations of pulsed energy depositions in a perfect gas. Experiments show that the discharge generates a cylindrical shock wave that travels at sonic speed after a few tens of microseconds, and produces an impulse that varies from 1 to 4 mN s m-1 and scales linearly with the linear energy density. This linearity agrees with the numerical simulations when 9.5% of the energy dissipated in the discharge is assumed to heat the gas. Overall, to produce a time-averaged force similar to the one achieved by dielectric barrier discharge (DBD) actuators, 2 to 3 times more power is required. However, surface discharge actuators do not saturate, and thus can induce time-averaged forces one or two orders of magnitude above DBD when pulsed at several hundreds of hertz.

  2. Enhanced efficiency from a Xe excimer barrier discharge lamp employing short-pulsed excitation

    Science.gov (United States)

    Mildren, Richard P.; Morrow, R.; Carman, Robert J.

    2000-04-01

    We have measured the efficiency and spatial characteristics of output radiation as a function of fill pressure for a Xe excimer lamp employing a short voltage pulse (approximately 100 ns) excitation circuit, and compared the results with those obtained using conventional AC (ie. sinusoidal voltage waveform). When using pulsed excitation, VUV output is obtained from a homogeneous discharge at efficiencies which increase linearly with Xe pressure in the range 50 - 750 torr up to 3.2X the maximum efficiency obtained when using AC. When using AC excitation, the efficiency saturates with increasing pressure > 350 torr for which pressures the discharge appearance is altered from a diffuse discharge to one which is comprised of stochastic or stationary filaments. We have also recorded discharge spectra which highlight the different character of the homogeneous and filamented types of discharges. It is deduced that the enhanced efficiency arises due to the capability of pulsed excitation to produce a homogeneous (glow-like) discharge at higher pressure, which brings about more optimal electron density and temperature conditions for exclusively exciting Xe metastables than possible using AC. We attribute the homogenizing effect of short-pulsed excitation to the rapid rate at which the applied E-field increases to the necessary value for homogeneous discharge breakdown to proceed at a faster rate than the formation of filaments.

  3. Discharge and optical characterizations of nanosecond pulse sliding dielectric barrier discharge plasma for volatile organic compound degradation

    Science.gov (United States)

    Jiang, Nan; Guo, Lianjie; Shang, Kefeng; Lu, Na; Li, Jie; Wu, Yan

    2017-04-01

    In this work, a nanosecond bipolar pulsed voltage coupled with a negative DC component is employed to generate sliding dielectric barrier discharge (DBD) plasma in a three-electrode geometry reactor and improve volatile organic compound (VOC) degradation at room temperature. The effects of the bipolar pulsed voltage (U ±pulse) and negative DC voltage (U ‑DC) on the discharge characteristic, optical characteristic, plasma gas temperature (T gas), and vibrational temperature (T vib) are discussed. The horizontal distribution characteristics of the N2(C3Πu  →  B3Πg) emission intensity, T gas, and T vib are also investigated to understand the propagation mechanism of sliding DBD along the dielectric surface. The experimental results reveal that a negative DC component applied to a third electrode can extend the plasma extension region, indicating that the gas ionization is ignited by the nanosecond high-voltage pulse, while charge drift is forced by the surface potential difference caused by the negative high-voltage DC. The T gas is measured by optical emission spectroscopy related to the rotational bands of N2(C3 Πu  →  B3Πg), and is approximately 375  ±  5 K under the condition of U ±pulse  =  20 kV and U ‑DC  =  ‑20 kV. Compared with typical surface DBD plasma, sliding DBD plasma is quasi-diffusive and distributed more uniformly within the whole discharge gap. Furthermore, both surface DBD and sliding DBD are used for removing toluene from flowing air. It is found that sliding DBD has higher toluene degradation efficiency and energy yield than surface DBD when they are excited by the positive pulsed voltage (U +pulse).

  4. The Effect of Flow Distribution on the Concentration of NO Produced by Pulsed Arc Discharge

    Institute of Scientific and Technical Information of China (English)

    HU Hui; BAO Bin; WANG He-li; LIANG Hai-yan; HE Jun-jia; HE Zheng-hao; LI Jin

    2007-01-01

    As a new method to cure acute respiratory distress syndrome (ARDS),high blood pressure and some illnesses related to the lung,NO has recently received more attention.Thermal plasmas produced by arc discharge can create medical NO,but the concentration of NO2 produced by arc discharge must be controlled simultaneously.This paper investigates the characteristics and regulations of NO production at different flow distribution by pulsed arc discharge in dry air with a special pulsed power.The experimental results show that the flow distribution has a considerable effect on the NO concentration,the stabilization of NO.The production of NO2 could be controlled and the ratio of NO2/NO was decreased to about 10% in the arc discharge.Therefore,the arc discharge could produce stable inhaled NO for medical treatment by changing the flow distribution.

  5. Rejection of partial-discharge-induced pulses in fission chambers designed for sodium-cooled fast reactors

    Science.gov (United States)

    Hamrita, H.; Jammes, C.; Galli, G.; Laine, F.

    2017-03-01

    Under given temperature and bias voltage conditions, partial discharges can create pulses in fission chambers. Based on experimental results, this phenomenon is in-depth investigated and discussed. A pulse-shape-analysis technique is proposed to discriminate neutron-induced pulses from partial-discharge-induced ones.

  6. 2D simulations of short-pulsed dielectric barrier discharge xenon excimer lamp

    Energy Technology Data Exchange (ETDEWEB)

    Bogdanov, E.A.; Kudryavtsev, A.A. [St. Petersburg State University, St. Petersburg (Russian Federation); Arslanbekov, R.R. [CFD Research Corporation, Huntsville (United States)

    2006-07-01

    Self-consistent two-dimensional (2D) simulations of short-pulsed dielectric barrier discharge (DBD) in pure xenon have been performed. It is shown that during short current pulse the traversal inhomogeneity of the plasma parameters can be important only at the end of the current pulse as an edge effect close to the side walls. During the current pulse, the gap voltage drops until the ionization wave reaches the cathode so the current in the cathode sheath is the displacement current. This means that almost all of the absorbed power is deposited into excitation of xenon atoms and not to the ion heating in the cathode sheath as in the traditional glow discharges. This fact is one of the reasons of high efficiency of short-pulsed DBD. The developed model allows one to estimate the temporal position of the plasma-sheath boundary. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  7. INPROVING OF THE QUALITY FOOD FOR ANIMALS BY PULSED POWER PLASMA DISCHARGE

    Directory of Open Access Journals (Sweden)

    Sebastian Gnapowski

    2015-08-01

    Full Text Available Soy beans powder mixed with water is a good food for animals. However, there are two problems with this brew. One is that soy beans powder is sunk down to fast. Parts of soy beans powder are too big and too heavy. Animals do not eat soy beans powder because after a few minutes (around 3min is sunk down and soy beans are on the bottom case. Another negative point is a quick growth of mold, especially during summer when the temperature is highest. Mold is making food unhealthy and causes unpleasant smell. After mold appears it is difficult to clean the case. One of the solutions to eliminate these problems is to use pulse power plasma discharge and the second solution is ultra sound treatment. It was observed that pulse power discharge can decrease the size of soy beans powder a few times. Another advantage of such experiments was that the pulse power discharge killed bacteria and viruses. After our experiments we did not observe mold growing. Using pulse power discharge we can decrease sinking speed by about ten times. Ultra sound generation is useful and can decrease sinking speed even more, compared with pulse power discharge.

  8. 电晕放电二氧化碳冷等离子体转化特性研究%STUDY ON CORONA DISCHARGE FOR CARBON DIOXIDE CONVERSION USING COLD PLASMA REACTION

    Institute of Scientific and Technical Information of China (English)

    李明伟; 许根慧; 刘昌俊; 姜涛

    2001-01-01

    在常压、室温条件下利用电晕放电使二氧化碳通过冷等离子体反应分解为一氧化碳和氧气,由四极质谱在线定量分析产物组成。考察反应条件(电晕类型、能量密度、气体流量等)对反应转化率的影响,分析了该反应的能量效率。当放电功率为40?W、CO2流量为30 mL*min-1时,正电晕等离子体CO2分解反应的转化率为15.2%;CO2转化率随体系能量密度的增加而上升,随反应时间的增加而增大。当CO2流量为90 mL*min-1、正电晕放电功率为37.6?W时,反应体系的能量效率为5.89%;实验发现,正电晕放电时CO2的转化率高于负电晕的转化率。%The decomposition of CO2 through corona discharge of cold plasma reaction at ambient temperature and atmosphere was carried out. A quadrupole mass spectrometer was employed for online quantity analysis of the products of CO2 plasma decomposition reaction. The effects of reaction parameters on conversion and energy efficiency, such as different corona discharges (include positive corona discharge, negative corona discharge), energy density, flow rate of feed, etc. were investigated. For the flow rate of CO2 at 30?mL*min-1, discharge power at 40?W, the CO2 conversion was 15.2% in positive corona plasma reaction. The conversion increased with increasing energy density and decreased with increasing CO2 flow rate. For CO2 flow rate at 90?mL*min-1, power at 37.6?W, the energy efficiency was 5.89% in positive corona plasma reaction. The conversion of CO2 in positive corona discharge is higher than that in negative corona discharge.

  9. Electric field measurements in a nanosecond pulse discharge in atmospheric air

    Science.gov (United States)

    Simeni Simeni, Marien; Goldberg, Benjamin M.; Zhang, Cheng; Frederickson, Kraig; Lempert, Walter R.; Adamovich, Igor V.

    2017-05-01

    The paper presents the results of temporally and spatially resolved electric field measurements in a nanosecond pulse discharge in atmospheric air, sustained between a razor edge high-voltage electrode and a plane grounded electrode covered by a thin dielectric plate. The electric field is measured by picosecond four-wave mixing in a collinear phase-matching geometry, with time resolution of approximately 2 ns, using an absolute calibration provided by measurements of a known electrostatic electric field. The results demonstrate electric field offset on the discharge center plane before the discharge pulse due to surface charge accumulation on the dielectric from the weaker, opposite polarity pre-pulse. During the discharge pulse, the electric field follows the applied voltage until ‘forward’ breakdown occurs, after which the field in the plasma is significantly reduced due to charge separation. When the applied voltage is reduced, the field in the plasma reverses direction and increases again, until the weak ‘reverse’ breakdown occurs, producing a secondary transient reduction in the electric field. After the pulse, the field is gradually reduced on a microsecond time scale, likely due to residual surface charge neutralization by transport of opposite polarity charges from the plasma. Spatially resolved electric field measurements show that the discharge develops as a surface ionization wave. Significant surface charge accumulation on the dielectric surface is detected near the end of the discharge pulse. Spatially resolved measurements of electric field vector components demonstrate that the vertical electric field in the surface ionization wave peaks ahead of the horizontal electric field. Behind the wave, the vertical field remains low, near the detection limit, while the horizontal field is gradually reduced to near the detection limit at the discharge center plane. These results are consistent with time-resolved measurements of electric field

  10. Nanosecond repetitively pulsed discharges in air at atmospheric pressure—the spark regime

    Science.gov (United States)

    Pai, David Z.; Lacoste, Deanna A.; Laux, Christophe O.

    2010-12-01

    Nanosecond repetitively pulsed (NRP) spark discharges have been studied in atmospheric pressure air preheated to 1000 K. Measurements of spark initiation and stability, plasma dynamics, gas temperature and current-voltage characteristics of the spark regime are presented. Using 10 ns pulses applied repetitively at 30 kHz, we find that 2-400 pulses are required to initiate the spark, depending on the applied voltage. Furthermore, about 30-50 pulses are required for the spark discharge to reach steady state, following initiation. Based on space- and time-resolved optical emission spectroscopy, the spark discharge in steady state is found to ignite homogeneously in the discharge gap, without evidence of an initial streamer. Using measured emission from the N2 (C-B) 0-0 band, it is found that the gas temperature rises by several thousand Kelvin in the span of about 30 ns following the application of the high-voltage pulse. Current-voltage measurements show that up to 20-40 A of conduction current is generated, which corresponds to an electron number density of up to 1015 cm-3 towards the end of the high-voltage pulse. The discharge dynamics, gas temperature and electron number density are consistent with a streamer-less spark that develops homogeneously through avalanche ionization in volume. This occurs because the pre-ionization electron number density of about 1011 cm-3 produced by the high frequency train of pulses is above the critical density for streamer-less discharge development, which is shown to be about 108 cm-3.

  11. Evolution of nanosecond surface dielectric barrier discharge for negative polarity of a voltage pulse

    Science.gov (United States)

    Soloviev, V. R.; Krivtsov, V. M.; Shcherbanev, S. A.; Starikovskaia, S. M.

    2017-01-01

    Surface dielectric barrier discharge, initiated by a high-voltage pulse of negative polarity in atmospheric pressure air, is studied numerically and experimentally. At a pulse duration of a few tens of nanoseconds, two waves of optical emission propagate from the high-voltage electrode corresponding to the leading and trailing edges of the high-voltage pulse. It is shown by means of numerical modeling that a glow-like discharge slides along the surface of the dielectric at the leading edge of the pulse, slowing down on the plateau of the pulse. When the trailing edge of the pulse arrives to the high-voltage electrode, a second discharge starts and propagates in the same direction. The difference is that the discharge corresponding to the trailing edge is not diffuse and demonstrates a well-pronounced streamer-like shape. The 2D (in numerical modeling) streamer propagates above the dielectric surface, leaving a gap of about 0.05 mm between the streamer and the surface. The calculated and experimentally measured emission picture, waveform of the electrical current, and deposited energy, qualitatively coincide. The sensitivity of the numerical solution to unknown physical parameters of the model is discussed.

  12. Field and laboratory studies of the nitrogen and oxygen isotopic composition of N2O: Corona discharge production, biomass burning, and ocean and "Arctic hot spot" emissions

    Science.gov (United States)

    Boering, K. A.

    2016-12-01

    While inverse modeling studies of atmospheric nitrous oxide (N2O) concentrations have narrowed uncertainties in the magnitudes, geographic distribution, and timing of N2O fluxes to the atmosphere that are needed to understand and to mitigate the rising concentration of this greenhouse gas and ozone depleting substance in the atmosphere, significant uncertainties remain, including accounting for the return of N2O-depleted air from the stratosphere. Measurements of the average and site-specific nitrogen and the oxygen isotopic compositions of N2O can provide an additional means to attribute observed N2O variations to its various sources or stratospheric sink [e.g., Park et al., 2012]. In this presentation, we will highlight recent laboratory work determining the isotopic composition of N2O produced in a corona discharge (the process that produces N2O in thunderstorms), showing it has an isotopic fingerprint that is distinct from that for soil and ocean emissions, for biomass burning, and for the return of air from the stratosphere. Although N2O produced by lightning is only a small fraction of the global annual source of N2O to the atmosphere, the large and unique isotopic signature of corona discharge N2O now characterized completes the array needed to identify the origin, for example, of the unexplained N2O enhancements measured in the tropical and subtropical upper troposphere during the 2009 HIPPO mission [Wofsy 2011]. Such N2O enhancements may also be consistent with inverse modeling studies [e.g., Hirsch et al., 2006; Huang et al., 2008] suggesting tropical N2O source(s) must be larger than expected from bottom-up inventories, so identifying the source of these enhancements is critical. Isotope compositions of N2O in a biomass burning plume in the tropical upper troposphere, from a Southern Ocean ship cruise, and from an Arctic peat circle `hot spot' will also be briefly compared and contrasted with the corona discharge results. Hirsch, A.I., et al., Glob

  13. Temperature and Nitric Oxide Generation in a Pulsed Arc Discharge Plasma

    Institute of Scientific and Technical Information of China (English)

    T.NAMIHIRA; S.SAKAI; M.MATSUDA; D.WANG; T.KIYAN; H.AKIYAMA; K.OKAMOTO; K.TODA

    2007-01-01

    Nitric oxide (NO) is increasingly being used in medical treatments of high blood pressure,acute respiratory distress syndrome and other illnesses related to the lungs.Currently a NO inhalation system consists of a gas cylinder of N2 mixed with a high concentration of NO.This arrangement is potentially risky due to the possibility of an accidental leak of NO from the cylinder.The presence of NO in the air leads to the formation of nitric dioxide (NO2),which is toxic to the lungs.Therefore,an on-site generator of NO would be highly desirable for medical doctors to use with patients with lung disease.To develop the NO inhalation system without a gas cylinder,which would include a high concentration of NO,NAMIHIRA et al have recently reported on the production of NO from room air using a pulsed arc discharge.In the present work,the temperature of the pulsed arc discharge plasma used to generate NO was measured to optimize the discharge condition.The results of the temperature measurements showed the temperature of the pulsed arc discharge plasma reached about 10,000 K immediately after discharge initiation and gradually decreased over tens of microseconds.In addition,it was found that NO was formed in a discharge plasma having temperatures higher than 9,000 K and a smaller input energy into the discharge plasma generates NO more efficiently than a larger one.

  14. Carbon Nanotube Fiber Ionization Mass Spectrometry: A Fundamental Study of a Multi-Walled Carbon Nanotube Functionalized Corona Discharge Pin for Polycyclic Aromatic Hydrocarbons Analysis

    Science.gov (United States)

    Nahan, Keaton S.; Alvarez, Noe; Shanov, Vesselin; Vonderheide, Anne

    2017-09-01

    Mass spectrometry continues to tackle many complicated tasks, and ongoing research seeks to simplify its instrumentation as well as sampling. The desorption electrospray ionization (DESI) source was the first ambient ionization source to function without extensive gas requirements and chromatography. Electrospray techniques generally have low efficiency for ionization of nonpolar analytes and some researchers have resorted to methods such as direct analysis in real time (DART) or desorption atmospheric pressure chemical ionization (DAPCI) for their analysis. In this work, a carbon nanotube fiber ionization (nanoCFI) source was developed and was found to be capable of solid phase microextraction (SPME) of nonpolar analytes as well as ionization and sampling similar to that of direct probe atmospheric pressure chemical ionization (DP-APCI). Conductivity and adsorption were maintained by utilizing a corona pin functionalized with a multi-walled carbon nanotube (MWCNT) thread. Quantitative work with the nanoCFI source with a designed corona discharge pin insert demonstrated linearity up to 0.97 (R2) of three target PAHs with phenanthrene internal standard. [Figure not available: see fulltext.

  15. Influence of Plasma Temperature on the Concentration of NO Produced by Pulsed Arc Discharge

    Institute of Scientific and Technical Information of China (English)

    胡辉; 陈卫鹏; 张锦丽; 陆僖; 何俊佳

    2012-01-01

    This study conducted experiments on producing inhaled medical nitric oxide (iNO) by pulsed arc discharge in dry and clean air under different discharge current. The concentration of NO and NO2 produced by air discharge, as well as the change of the ratio of NO2/NO under different discharge current were investigated. Through the analysis of plasma emission spectrum, the relationship between discharge current and arc plasma temperature was studied. The results indicate that, as discharge current increases, the arc plasma temperature increases, which then leads to the increase of NO concentration, the decrease of NO2 concentration, and the rapid decrease of the ratio of NO2/NO. When the plasma temperature is 9000 K, the ratio of NO2/NO is approximately 60%, while when the plasma temperature varies between 10550 K and 11300 K, the NO2/NO ratio is within the range of 4.2% to 4.6%.

  16. Studies of the properties of polypropylene non-woven treated by corona discharge and radio frequency plasma

    OpenAIRE

    Selma Aparecida Lopes

    2012-01-01

    Resumo: O material polimérico denominado não tecido de polipropileno (NTPP), após receber adequado tratamento químico, tem sido largamente utilizado na indústria têxtil para confecção de produtos de higiene pessoal, fraldas e absorventes descartáveis. Neste sentido o presente trabalho analisa os efeitos das técnicas de descarga corona (atmosfera ambiente) e plasma por radiofrequência (atmosferas de oxigênio (O2), nitrogênio (N2) e argônio (Ar) causados nas propriedades de superfície de amostr...

  17. The Chlorella killed by pulsed electrical discharge in liquid with two different reactors

    Science.gov (United States)

    Gao, Z. Y.; Sun, B.; Yan, Z. Y.; Zhu, X. M.; Liu, H.; Song, Y. J.; Sato, M.

    2013-03-01

    The application of pulsed high-voltage discharge in liquid has attracted wide attention as an effective water treatment. In this paper, two different liquid high-voltage discharge systems were constructed with plate-hole-plate and needle-plate electrode structures, and the inactivation behaviors of Chlorella were studied in the two reactors. The results show that the killing rates of algae in both reactors all increased significantly with increasing discharge voltage and the killing rates were intensely related to discharge power, instantaneous power and single pulse input energy. Furthermore, the inactivation effect in needle-plate reactor was superior to that in plate-hole-plate reactor under the same experimental conditions.

  18. Comparison of Cocaine Detections in Corona Discharge Ionization-Ion Mobility Spectrometry and in Atmospheric Pressure Chemical Ionization-Mass Spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Sung Seen; Kim, Yun Ki; Kim, Ok Bae [Sejong University, Seoul (Korea, Republic of); An, Seung Geon; Shin, Myung Won; Maeng, Seug Jin; Choi, Gyu Seop [Wooju Communication and Technology Co., Seoul (Korea, Republic of)

    2010-08-15

    In this study, we determined the detection limit and reproducibility of the new IMS equipped with corona discharge ionization source using cocaine. The sample was injected with liquid solution to compare the results of APCI-MS. Ion mobility spectrometry (IMS) was a technique originally applied for the detection of trace compounds. IMS has been widely used to detect chemical warfare agents, explosives, and illegal drugs since it combines both high sensitivity (detection limits down to the ng/L range to pg/L range, ppb range and ppt range) and relatively low technical expenditure with high-speed data acquisition. The time required to acquire a single spectrum is in the range of several tens ms. The working principle is based on the drift of ions at ambient pressure under the influence of an external electric field.

  19. Back corona enhanced organic film deposition inside an Atmospheric Pressure Weakly Ionized Plasma reactor

    Science.gov (United States)

    Islam, Rokibul; Xie, Shuzheng; Englund, Karl; Pedrow, Patrick

    2014-10-01

    A grounded screen with short needle-like protrusions has been designed to generate back corona in an Atmospheric Pressure Weakly Ionized Plasma (APWIP) reactor. The grounded screen with protrusions is placed downstream at a variable gap length from an array of needles that is energized with 60 Hz high voltage. The excitation voltage is in the range 0--10 kV RMS and the feed gas mixture consists of argon and acetylene. A Lecroy 9350AL 500 MHz digital oscilloscope is used to monitor the reactor voltage and current using a resistive voltage divider and a current viewing resistor, respectively. The current signal contains many positive and negative current pulses associated with corona discharge. Analysis of the current signal shows asymmetry between positive and negative corona discharge currents. Photographs show substantial back corona generated near the tips of the protrusions situated at the grounded screen. The back corona activates via bond scission acetylene radicals that are transported downstream to form a plasma-polymerized film on a substrate positioned downstream from the grounded screen. The oscillograms will be used to generate corona mode maps that show the nature of the corona discharge as a function of gap spacing, applied voltage and many other reactor parameters.

  20. A High Voltage High Frequency Resonant Inverter for Supplying DBD Devices with Short Discharge Current Pulses

    OpenAIRE

    Bonnin, Xavier; Brandelero, Julio; Videau, Nicolas; Piquet, Hubert; Meynard, Thierry

    2014-01-01

    International audience; In this paper, the merits of a high-frequency resonant converter for supplying dielectric barrier discharges (DBD) devices are established. It is shown that, thanks to its high-frequency operating condition, such a converter allows to supply DBD devices with short discharge current pulses, a high repetition rate, and to control the injected power. In addition, such a topology eliminates the matter of connecting a high-voltage transformer directly across the DBD device ...

  1. Pulsed electrical discharges in water for removal of organic pollutants: a comparative study

    OpenAIRE

    Dang, T.H.; Denat, A.; Lesaint, O.; Teissedre, G.

    2009-01-01

    Abstract In this study, the efficiency of different types of pulsed electrical discharges for the removal of organic pollutants from wastewater has been determined. Three discharge types, either in the water volume or in close proximity to the water surface are studied. The production of hydrogen peroxide in pure water, and the degradation of two typical pollutants (4-chlorophenol and 4-nitrophenol) is measured together with the amount of electrical energy d...

  2. The role of molecular vibration in nanosecond repetitively pulsed discharges and in DBDs in hydrogen plasmas

    Science.gov (United States)

    Colonna, G.; D'Ammando, G.; Pietanza, L. D.

    2016-10-01

    A self-consistent state-to-state model of pure hydrogen has been used to investigate the development of nanosecond repetitively pulsed discharges and dielectric barrier discharges, the latter coupling the kinetic model with an equation for the circuit, thus mimicking an insulated electrode with an external capacitance. Vibrationally excited states play a fundamental role, affecting the degrees of dissociation and ionization, as well as internal and free-electron distributions.

  3. A Repetitive Nanosecond Pulse Source for Generation of Large Volume Streamer Discharge

    Institute of Scientific and Technical Information of China (English)

    TAO Fengbo; ZHANG Qiaogen; GAO Bo; WANG Hu; LI Zhou

    2008-01-01

    Using a unipolar pulse with the rise time and the pulse duration in the order of microsecond as the primary pulse,a nanosecond pulse with the repetitive frequency of several kilohertz is generated by a spark gap switch.By varying both the inter-pulse duration and the pulse frequency,the voltage recovery rate of the spark gap switch is investigated at different working conditions such as the gas pressure,the gas composition as well as the bias voltage.The results reveal that either increase in gas pressure or addition of SF6 to the air can increase the voltage recovery rate.The effect of gas composition on the voltage recovery rate is discussed based on the transferring and distribution of the residual space charges.The repetitive nanosecond pulse source is also applied to the generation of large volume,and the discharge currents are measured to investigate the effect of pulse repetition rate on the large volume streamer discharge.

  4. High Power Semiconductor Devices and Solid State Switches for Pulsed Discharge Applications

    OpenAIRE

    Fleischmann, W.; Welleman, A.

    2006-01-01

    Based on long term experience, collected mainly with military applications like Rail Guns and Active Armour, a range of optimized semiconductor devices for pulsed applications was developed by ABB Switzerland Ltd and described in this presentation. The presented devices are optimized for pulsed discharge and fit very well for switching the short but high electrical power demand used for magnetic forming. Devices are available in different versions with silicon wafer diameters up to 120 mm and...

  5. Numerical and analytical studies of critical radius in spherical and cylindrical geometries for corona discharge in air and CO2-rich environments

    Science.gov (United States)

    Engle, J. A.; Riousset, J. A.

    2016-12-01

    In order to determine the most effective geometry of a lightning rod, one must first understand the physical difference between their current designs. Benjamin Franklin's original theory of sharp tipped rods suggests an increase of local electric field, while Moore et al.'s (2000) studies of rounded tips evince an increased probability of strike (Moore et al., 2000; Gibson et al., 2009).In this analysis, the plasma discharge is produced between two electrodes with a high potential difference, resulting in ionization of the neutral gas particle. This process, when done at low current and low temperature can create a corona discharges, which can be observed as a luminescent emission. The Cartesian geometry known as Paschen, or Townsend, theory is particularly well suited to model experimental laboratory scenario, however, it is limited in its applicability to lightning rods. Franklin's sharp tip and Moore et al.'s (2000) rounded tip fundamentally differ in the radius of curvature of the upper end of the rod. As a first approximation, the rod can be modelled as an equipotential conducting sphere above the ground. Hence, we expand the classic Cartesian geometry into spherical and cylindrical geometries. In this work we explore the effects of shifting from the classical parallel plate analysis to spherical and cylindrical geometries more adapted for studies of lightning rods or power lines. Utilizing Townsend's equation for corona discharge, we estimate a critical radius and minimum breakdown voltage that allows ionization of the air around an electrode. Additionally, we explore the influence of the gas in which the discharge develops. We use BOLSIG+, a numerical solver for the Boltzmann equation, to calculate Townsend coefficients for CO2-rich atmospheric conditions. This allows us to expand the scope of this study to other planetary bodies such as Mars (Hagelaar, 2005). We solve the problem both numerically and analytically to present simplified formulas per each

  6. Pulsed power supply and coaxial reactor applied to E. coli elimination in water by pulsed dielectric barrier discharge

    Energy Technology Data Exchange (ETDEWEB)

    Quiroz V, V. E.; Lopez C, R.; Rodriguez M, B. G.; Pena E, R.; Mercado C, A.; Valencia A, R.; Hernandez A, A. N.; Barocio, S. R.; Munoz C, A. E. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); De la Piedad B, A., E-mail: regulo.lopez@inin.gob.mx [Instituto Tecnologico de Toluca, Av. Tecnologico s/n, Ex-Rancho La Virgen, 52140 Metepec, Estado de Mexico (Mexico)

    2013-07-01

    The design and instrumentation intended for ATTC8739 Escherichia coli (E. coli) bacteria elimination in water, based on non thermal plasma generation at room pressure have been carried out by means of dielectric pulsed discharges. The latter have been produced by a power supply capable of providing voltages up to the order of 45 kV, 1-500 {mu}s pulse widths and variable frequencies between 100 Hz to 2000 Hz. This supply feeds a coaxial discharge reactor of the simple dielectric barrier type. The adequate operation of the system has been tested with the elimination of E. coli at 10{sup 4} and 10{sup 6} bacteria/ml concentrations, leading to reductions up to 85.3% and 95.1%, respectively, during the first 30 min of treatment. (Author)

  7. Characteristics of High Speed Electro-thermal Jet Activated by Pulsed DC Discharge

    Institute of Scientific and Technical Information of China (English)

    Jichul Shin

    2010-01-01

    Experimental study of synthetic jet produced by pulsed direct current (DC) discharge is presented.High velocity jet is activated electro-thermally by high frequency pulsed DC discharge in small cavity.A cavity of 2.38 mm diameter cylinder bounded by circular electrode is made in a ceramic plate and a small orifice of 1.78 mm diameter is drilled in the middle of cavity.High frequency pulsed DC discharge instantaneously heats air in the cavity and produces high velocity jet at the exit of the orifice.Schlieren imaging at high framing rate of 100 kHz reveals the presence of supersonic precursor shock followed by the jet emerging from the orifice.The jet velocity reaches as high as about 300 m/s.Jet with smaller cavity volume produces lesser effect and jet velocity reaches maximum at certain cavity volume with given discharge current and orifice size.As duty time of pulse increases from 5 to 20 μs at fixed frequency of 5 kHz,the jet velocity also increases and becomes nearly constant with further increase in duty time.At fixed duty time of 20 μs,higher frequency pulsing of 10 kHz produces degradation of the jet as the discharge pulse continues.The jet developed in this study is demonstrated to be strong enough to penetrate deep into supersonic boundary layer and to produce a bow shock when the jet is issued into Math 3 supersonic flow.

  8. [Spectroscopic study on the high voltage fast pulsed discharge of nitrogen, ammonia or their mixture].

    Science.gov (United States)

    Liu, Z P; Wang, P N; Yang, W D; Zheng, J B; Li, F M

    2001-10-01

    The emission spectra from the pulsed discharge plasma of nitrogen, ammonia or their mixture were measured. In the discharge of pure nitrogen gas, as the pressure increased, the discharge volume decreased and more dissociation of nitrogen molecules occurred due to the higher energy density. In the discharge of ammonia, N,N+ and NH+ were observed, but no NH2 and NH3 were detected, indicating that ammonia, which has the lower dissociation and ionization energies as compared to nitrogen, was highly dissociated. The discharge of the mixture of N2 and NH3 was also studied. The dependence of the dissociation of nitrogen on the ratio of nitrogen to ammonia was investigated by emission spectra. The optimal ratio for nitrogen dissociation was obtained. The advantage of using the mixture of nitrogen and ammonia in the synthesis of nitrides was discussed.

  9. Generation of nanosecond pulses in a barrier-discharge XeBr excimer lamp

    Science.gov (United States)

    Avdeev, S. M.; Kostyrya, I. D.; Sosnin, É. A.; Tarasenko, V. F.

    2006-07-01

    The subject of investigation is the coaxial two-barrier short-pulse excimer lamp based on XeBr* molecules (λ = 282 nm). When the working mixture (Xe: Br2 = 70: 1) is excited by a high-voltage pulsed nanosecond discharge at a pressure of 1 atm, the peak power of the generated radiation is on the order of 100 kW at an FWHM of 4.5 ns. If the gap between the barriers is small, a train of pulses with an FWHM of 20 ns and a repetition rate of 200 kHz may be obtained.

  10. A comparative study on continuous and pulsed RF argon capacitive glow discharges at low pressure by fluid modeling

    Science.gov (United States)

    Liu, Ruiqiang; Liu, Yue; Jia, Wenzhu; Zhou, Yanwen

    2017-01-01

    Based on the plasma fluid theory and using the drift-diffusion approximation, a mathematical model for continuous and pulsed radial frequency (RF) argon capacitive glow discharges at low pressure is established. The model is solved by a finite difference method and the numerical results are reported. Based on the systematic analysis of the results, plasma characteristics of the continuous and pulsed RF discharges are comparatively investigated. It is shown that, under the same condition for the peak value of the driving potential, the cycle-averaged electron density, the current density, and other essential physical quantities in the continuous RF discharge are higher than those from the pulsed RF discharge. On the other hand, similar plasma characteristics are obtained with two types of discharges, by assuming the same deposited power. Consequently, higher driving potential is needed in pulsed discharges in order to maintain the same effective plasma current. Furthermore, it is shown that, in the bulk plasma region, the peak value of the bipolar electric field from the continuous RF discharge is greater than that from the pulsed RF discharge. In the sheath region, the ionization rate has the shape of double-peaking and the explanation is given. Because the plasma input power depends on the driving potential and the plasma current phase, the phase differences between the driving potential and the plasma current are compared between the continuous and the pulsed RF discharges. It is found that this phase difference is smaller in the pulsed RF discharge compared to that of the continuous RF discharge. This means that the input energy coupling in the pulsed RF discharge is less efficient than the continuous counterpart. This comparative study, carried out also under other conditions, thus can provide instructive ideas in applications using the continuous and pulsed RF capacitive glow discharges.

  11. Electric field induced needle-pulsed arc discharge carbon nanotube production apparatus: circuitry and mechanical design.

    Science.gov (United States)

    Kia, Kaveh Kazemi; Bonabi, Fahimeh

    2012-12-01

    A simple and low cost apparatus is reported to produce multiwall carbon nanotubes and carbon nano-onions by a low power short pulsed arc discharge reactor. The electric circuitry and the mechanical design details and a micro-filtering assembly are described. The pulsed-plasma is generated and applied between two graphite electrodes. The pulse width is 0.3 μs. A strong dc electric field is established along side the electrodes. The repetitive discharges occur in less than 1 mm distance between a sharp tip graphite rod as anode, and a tubular graphite as cathode. A hydrocarbon vapor, as carbon source, is introduced through the graphite nozzle in the cathode assembly. The pressure of the chamber is controlled by a vacuum pump. A magnetic field, perpendicular to the plasma path, is provided. The results show that the synergetic use of a pulsed-current and a dc power supply enables us to synthesize carbon nanoparticles with short pulsed plasma. The simplicity and inexpensiveness of this plan is noticeable. Pulsed nature of plasma provides some extra degrees of freedom that make the production more controllable. Effects of some design parameters such as electric field, pulse frequency, and cathode shape are discussed. The products are examined using scanning probe microscopy techniques.

  12. Electric field induced needle-pulsed arc discharge carbon nanotube production apparatus: Circuitry and mechanical design

    Science.gov (United States)

    Kia, Kaveh Kazemi; Bonabi, Fahimeh

    2012-12-01

    A simple and low cost apparatus is reported to produce multiwall carbon nanotubes and carbon nano-onions by a low power short pulsed arc discharge reactor. The electric circuitry and the mechanical design details and a micro-filtering assembly are described. The pulsed-plasma is generated and applied between two graphite electrodes. The pulse width is 0.3 μs. A strong dc electric field is established along side the electrodes. The repetitive discharges occur in less than 1 mm distance between a sharp tip graphite rod as anode, and a tubular graphite as cathode. A hydrocarbon vapor, as carbon source, is introduced through the graphite nozzle in the cathode assembly. The pressure of the chamber is controlled by a vacuum pump. A magnetic field, perpendicular to the plasma path, is provided. The results show that the synergetic use of a pulsed-current and a dc power supply enables us to synthesize carbon nanoparticles with short pulsed plasma. The simplicity and inexpensiveness of this plan is noticeable. Pulsed nature of plasma provides some extra degrees of freedom that make the production more controllable. Effects of some design parameters such as electric field, pulse frequency, and cathode shape are discussed. The products are examined using scanning probe microscopy techniques.

  13. High-pressure (>1-bar) dielectric barrier discharge lamps generating short pulses of high-peak power vacuum ultraviolet radiation

    Energy Technology Data Exchange (ETDEWEB)

    Carman, R J; Mildren, R P; Ward, B K; Kane, D M [Short Wavelength Interactions with Materials (SWIM), Physics Department, Macquarie University, North Ryde, Sydney, NSW 2109 (Australia)

    2004-09-07

    We have investigated the scaling of peak vacuum ultraviolet output power from homogeneous Xe dielectric barrier discharges excited by short voltage pulses. Increasing the Xe fill pressure above 1-bar provides an increased output pulse energy, a shortened pulse duration and increases in the peak output power of two to three orders of magnitude. High peak power pulses of up to 6 W cm{sup -2} are generated with a high efficiency for pulse rates up to 50 kHz. We show that the temporal pulse characteristics are in good agreement with results from detailed computer modelling of the discharge kinetics.

  14. Experimental study on dielectric barrier discharge actuators operating in pulse mode

    NARCIS (Netherlands)

    Kotsonis, M.; Veldhuis, L.

    2010-01-01

    An experimental investigation is performed on the operation of dielectric barrier discharge plasma actuators used as manipulators of secondary and unsteady flow structures such as boundary layer instabilities or shedding vortices. The actuators are tested mainly in pulse mode. High sample rate hot-w

  15. The effects of high-voltage pulse electric discharges on ion adsorption on activated carbons

    Science.gov (United States)

    Gafurov, M. M.; Sveshnikova, D. A.; Larin, S. V.; Rabadanov, K. Sh.; Shabanova, Z. E.; Yusupova, A. A.; Ramazanov, A. Sh.

    2008-07-01

    The effects of high-voltage pulse electric discharges (HPED) on sorption of boron and sulfate ions on activated carbons of different kinds (KM-2, BAU, DAK) were investigated. The effect of HPED activation on the sorption characteristics of the systems was found to be similar to the temperature effect.

  16. Characterization of a high-power/current pulsed magnetized arc discharge

    NARCIS (Netherlands)

    Zielinski, J. J.; van der Meiden, H. J.; Morgan, T. W.; D.C. Schram,; De Temmerman, G.

    2012-01-01

    A high-power pulsed magnetized arc discharge has been developed to allow the superimposition of a dc plasma and a high-power plasma impulse with a single plasma source. A capacitor bank (8400 mu F) is parallel-coupled to the current regulated power supply. The current is transiently increased from i

  17. Plasma-Enhanced Combustion of Hydrocarbon Fuels and Fuel Blends Using Nanosecond Pulsed Discharges

    Energy Technology Data Exchange (ETDEWEB)

    Cappelli, Mark; Mungal, M Godfrey

    2014-10-28

    This project had as its goals the study of fundamental physical and chemical processes relevant to the sustained premixed and non-premixed jet ignition/combustion of low grade fuels or fuels under adverse flow conditions using non-equilibrium pulsed nanosecond discharges.

  18. Development and Applications of discharges generated in liquids with short high voltage pulses

    Science.gov (United States)

    Kolb, Juergen; Miron, Camelia; Kruth, Angela; Balcerak, Michal; Bonislawski, Michal; Holub, Marcin

    2016-09-01

    Discharges that are generated within a liquid have been of scientific interest for more than a century. The possibility for a breakdown development that is not mediated by an initial gaseous phase is still disputed. In this respect are especially discharges that are instigated with short high voltage pulses calling for attention. Associated with this specific excitation scheme is a change in plasma development, plasma parameters and reaction mechanisms in the liquid. We have compared discharges in a point-to-plane geometry that were generated with 50-us or 10-ns high voltage pulses. Time-resolved shadowgraphy and spectroscopy were performed to evaluate discharge structures, plasma parameter and reactive species that were formed in distilled water or ethanol. Different propagation modes, with velocities of 6.7 km/s for tree-like streamers and only 50 m/s for bush-like streamers, were observed. Optical emission spectroscopy has shown the formation of molecular bands of nitrogen, as well as strongly broadened atomic hydrogen and oxygen, which are likely to be responsible for the observed surface modifications of polymers. With nanosecond high voltage pulses we found an increase of unsaturated bondings for polyimide surfaces that were exposed in the discharge volume.

  19. Radiative Characteristics of the Pulse-Periodic Discharge Plasma Initiated by Runaway Electrons

    Science.gov (United States)

    Lomaev, M. I.; Beloplotov, D. V.; Tarasenko, V. F.; Sorokin, D. A.

    2016-07-01

    Results of experimental investigations of amplitude-temporal and spectral characteristics of radiation of a pulse-periodic discharge plasma initiated in nitrogen by runaway electrons are presented. The discharge was initiated by high-voltage nanosecond voltage pulses with repetition frequency of 60 Hz in a sharply inhomogeneous electric field in a gap between the conic potential cathode and the planar grounded aluminum anode. It is established that intensive lines of Al I atoms and Al II atomic ions, lines of N I atoms and N II ions, bands of the first (1+) and second positive (2+) nitrogen systems, as well as bands of cyanogen CN are observed in the emission spectrum of the discharge plasma under the given excitation conditions.

  20. The impacts of magnetic field on repetitive nanosecond pulsed dielectric barrier discharge in air

    Science.gov (United States)

    Liu, Yidi; Qi, Haicheng; Fan, Zhihui; Yan, Huijie; Ren, ChunSheng

    2016-11-01

    In this paper, the impacts of the parallel magnetic field on the repetitive nanosecond pulsed dielectric barrier discharge (DBD) are experimentally investigated by optical and electrical measurements. The DBD is generated between two parallel-plate electrodes in the ambient air with the stationary magnetic field on the order of 1 T. The experimental results show that additional microdischarge channels are generated and the photocurrent intensity of the plasma is increased by the magnetic field. The microdischarge channels develop along the magnetic field lines and the diffuse background emission of the discharge is stronger in the DBD with the magnetic field. As the pulse repetition frequency decreases from 1200 Hz to 100 Hz, only the photocurrent intensity of the third discharge that occurred at about 500 ns is noticeably increased by the additional magnetic field. It is believed that the enhancement of the memory effect and the confinement of the magnetic field on electrons are the main reasons.

  1. Fundamental Research on Mercuryless Fluorescent Lamps I — Inner Electrode Operation with Pulsed Discharge

    Science.gov (United States)

    Jinno, Masafumi; Aono, Hisayoshi

    1999-07-01

    The characteristics of xenon-neon discharge fluorescent lamps with inner electrodes are described in this paper.All lamps were operated by pulsed discharge.When the partial pressure of neon is high, the ignition voltage and operation voltage are low because of the Penning effect.Thus, a higher mixing ratio of neon is desirable for lower ignition and operation voltages.However, the luminance of phosphor increases as the mixing ratio of xenon increases.As the pressure of xenon increases, the second peak of phosphor emission in afterglow increases.These increases seem to be caused by the VUV light of xenon excimers.Therefore, though there is the problem of ion bombardment of the cathode under a high operation voltage, the pulsed discharge of the xenon-neon mixture at a high xenon mixing ratio is desirable in mercuryless fluorescent lamps because a strong radiation of xenon excimer is obtained.

  2. Numerical simulation of narrow bipolar electromagnetic pulses generated by thunderstorm discharges

    Science.gov (United States)

    Bochkov, E. I.; Babich, L. P.; Kutsyk, I. M.

    2013-07-01

    Using the concept of avalanche relativistic runaway electrons (REs), we perform numerical simulations of compact intracloud discharge (CID) as a generator of powerful natural electromagnetic pulses (EMPs) in the HF-VHF range, called narrow bipolar pulses (NBPs). For several values of the field overvoltage and altitude at which the discharge develops, the numbers of seed electrons initiating the avalanche are evaluated, with which the calculated EMP characteristics are consistent with the measured NBP parameters. We note shortcomings in the hypothesis assuming participation of cosmic ray air showers in avalanche initiation. The discharge capable of generating NBPs produces REs in numbers close to those in the source of terrestrial γ-ray flashes (TGFs), which can be an argument in favor of a unified NBP and TGF source.

  3. Numerical simulation of narrow bipolar electromagnetic pulses generated by thunderstorm discharges

    Energy Technology Data Exchange (ETDEWEB)

    Bochkov, E. I.; Babich, L. P., E-mail: babich@elph.vniief.ru; Kutsyk, I. M. [All-Russia Research Institute of Experimental Physics, Russian Federal Nuclear Center (Russian Federation)

    2013-07-15

    Using the concept of avalanche relativistic runaway electrons (REs), we perform numerical simulations of compact intracloud discharge (CID) as a generator of powerful natural electromagnetic pulses (EMPs) in the HF-VHF range, called narrow bipolar pulses (NBPs). For several values of the field overvoltage and altitude at which the discharge develops, the numbers of seed electrons initiating the avalanche are evaluated, with which the calculated EMP characteristics are consistent with the measured NBP parameters. We note shortcomings in the hypothesis assuming participation of cosmic ray air showers in avalanche initiation. The discharge capable of generating NBPs produces REs in numbers close to those in the source of terrestrial {gamma}-ray flashes (TGFs), which can be an argument in favor of a unified NBP and TGF source.

  4. Numerical Study of Pulsed Dielectric Barrier Discharge at Atmospheric Pressure Under the Needle-Plate Electrode Configuration

    Institute of Scientific and Technical Information of China (English)

    WANG Yanhui; YE Huanhuan; ZHANG Jiao; WANG Qi; ZHANG Jie; WANG Dezhen

    2016-01-01

    In this paper,we study the characteristics of atmospheric-pressure pulsed dielectric barrier discharge (DBD) under the needle-plate electrode configuration using a one-dimensional self-consistent fluid model.The results show that,the DBDs driven by positive pulse,negative pulse and bipolar pulse possess different behaviors.Moreover,the two discharges appearing at the rising and the falling phases of per voltage pulse also have different discharge regimes.For the case of the positive pulse,the breakdown field is much lower than that of the negative pulse,and its propagation characteristic is different from the negative pulse DBD.When the DBD is driven by a bipolar pulse voltage,there exists the interaction between the positive and negative pulses,resulting in the decrease of the breakdown field of the negative pulse DBD and causing the change of the discharge behaviors.In addition,the effects of the discharge parameters on the behaviors of pulsed DBD in the needle-plate electrode configuration are also studied.

  5. Generation of alkali-free and high-proton concentration layer in a soda lime glass using non-contact corona discharge

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, Hiroshi; Sakai, Daisuke; Nishii, Junji [Research Institute for Electronic Science, Hokkaido University, N20 W10, Kita-ku, Sapporo, Hokkaido 001-0020 (Japan); Funatsu, Shiro [Production Technology Center, Asahi Glass Co., Ltd., 1-1 Suehiro-cyo, Tsurumiku, Yokohama, Kanagawa 230-0045 (Japan); Yamamoto, Kiyoshi; Suzuki, Toshio [Research Center, Asahi Glass Co., Ltd., 1150 Hazawa-cho, Kanagawa-ku, Yokohama, Kanagawa 221-8755 (Japan); Harada, Kenji [Department of Computer Science, Kitami Institute of Technology, 165 Koen-cho, Kitami, Hokkaido 090-8507 (Japan)

    2013-08-14

    Formation mechanisms of alkali-free and high-proton concentration surfaces were investigated for a soda lime glass using a corona discharge treatment under an atmospheric pressure. Protons produced by high DC voltage around an anode needle electrode were incorporated into a sodium ion site in the anode side glass. The sodium ion was swept away to the cathode side as a charge carrier. Then it was discharged. The precipitated sodium was transformed to a Na{sub 2}CO{sub 3} powder when the surface contacted with air. The sodium ion in the glass surface layer of the anode side was replaced completely by protons. The concentration of OH groups in the layer was balanced with the amount of excluded sodium ions. The substitution reaction of sodium ions with protons tends to be saturated according to a square root function of time. The alkali depletion layer formation rate was affected by the large difference in mobility between sodium ions and protons in the glass.

  6. Testifying experiment of the multi-pulse phenomena of capillary discharge soft-X-ray laser

    Institute of Scientific and Technical Information of China (English)

    Bohan Luan; Yongpeng Zhao; Qi Wang; Yuanli Cheng; Yao Xie

    2008-01-01

    In a capillary discharge experiment for the neon-like argon lasing, we have proposed an experimental scheme to verify that the multi-spike of X-ray diode (XRD) signal is a multi-pulse laser or is a reflection of the laser pulse in the XRD.The ceramic capillary has an inner diameter of 3mm and a length of 200mm.At the gas pressure of 28Pa and discharge current of 27kA, stable lasing has been realized.The experimental results prove that the multi-spike of XRD signal is a reflection of the electromagnetic signal produced by the laser pulse in the XRD.The improved electrocircuit scheme of the XRD to minimize the reflection phenomena is also found.

  7. Particle Densities of the Atmospheric-Pressure Argon Plasmas Generated by the Pulsed Dielectric Barrier Discharges

    Science.gov (United States)

    Pan, Jie; Li, Li; Wang, Yunuan; Xiu, Xianwu; Wang, Chao; Song, Yuzhi

    2016-11-01

    Atmospheric-pressure argon plasmas have received increasing attention due to their high potential in many industrial and biomedical applications. In this paper, a 1-D fluid model is used for studying the particle density characteristics of the argon plasmas generated by the pulsed dielectric barrier discharges. The temporal evolutions of the axial particle density distributions are illustrated, and the influences of changing the main discharge conditions on the averaged particle densities are researched by independently varying the various discharge conditions. The calculation results show that the electron density and the ion density reach two peaks near the momentary cathodes during the rising and the falling edges of the pulsed voltage. Compared with the charged particle densities, the densities of the resonance state atom Arr and the metastable state atom Arm have more uniform axial distributions, reach higher maximums and decay more slowly. During the platform of the pulsed voltage and the time interval between the pulses, the densities of the excited state atom Ar* are far lower than those of the Arr or the Arm. The averaged particle densities of the different considered particles increase with the increases of the amplitude and the frequency of the pulsed voltage. Narrowing the discharge gap and increasing the relative dielectric constant of the dielectric also contribute to the increase of the averaged particle densities. The effects of reducing the discharge gap distance on the neutral particle densities are more significant than the influences on the charged particle densities. supported by Natural Science Foundation of Shandong Province, China (No. ZR2015AQ008), and Project of Shandong Province Higher Educational Science and Technology Program of China (No. J15LJ04)

  8. Schlieren Imaging and Pulsed Detonation Engine Testing of Ignition by a Nanosecond Repetitively Pulsed Discharge

    Science.gov (United States)

    2016-05-16

    effect of the plasma is to produce active species, which quench to produce O atoms and release heat. The O atoms go on to initiate the fuel oxidation ...strong effect on ignition time for mixtures with MIE larger than the individual pulse energy. Stoichiometric ethylene –air has an MIE of 0.096 mJ... ethylene is so fast with just a single pulse, the effect of additional pulses is not noticeable on the time scale of the present experiments. In addition

  9. Experimental research of pulsed discharge plasma and TiO2/Zeolite coupling technology for formaldehyde removal

    Science.gov (United States)

    Dong, Bingyan; Lan, Shuirong

    2013-03-01

    The pulsed discharge plasma combining with catalyst to remove formaldehyde is a novel type of advanced oxidation technology. In the present work, taking wire-tube pulsed discharge plasma and TiO2/Zeolite coupling technology for formaldehyde removal. The studies have investigated the wire-tube reactor with zeolite, TiO2, TiO2/Zeolite for formaldehyde removal respectively. Results show that in the optimal experimental conditions and the baking time is 120 min, the baking temperature is 450 °C, that TiO2/Zeolite catalyst which made by sol-gel shows higher photocatalytic activity and efficiency. The pulsed discharge with TiO2/Zeolite catalyst for formaldehyde removal has higher removal efficiency than pulsed discharge with zeolite or TiO2. Therefore, pulsed discharge plasma with TiO2/Zeolite for the removal of formaldehyde can greatly increase the removal efficiency.

  10. High-pressure dielectric barrier discharge Xenon lamps generating short pulses of high-peak-power VUV radiation (172nm) with high pulse-to-pulse reproducibility.

    Science.gov (United States)

    Carman, Robert; Ward, Barry; Mildren, Richard; Kane, Deborah

    2003-10-01

    Dielectric barrier discharges (DBDs) are used to efficiently generate radiation in the ultraviolet and vacuum-ultraviolet spectral regions (88nm-350nm) by forming rare-gas and rare-gas halide excimers in a transient plasma. Usually, DBD lamps generate the light output quasi-continuously or in bursts with a high degree of stochastic or random variability in the instantaneous UV/VUV intensity. However, regular pulses of high-peak-power UV/VUV, with high pulse-to-pulse reproducibility, are of interest for applications in biology, surface treatment and cleaning, and time-resolved fluorescence spectroscopy. Such pulses can be generated from spatially homogeneous plasmas in a Xe DBD when the discharge is driven by uni-polar voltage pulses of short duration ( 100ns)^1. In the present study, we will report Xe DBD lamp performance and VUV output pulse characteristics for gas pressures up to 2.5bar and excitation conditions tailored for high-peak-power output. The experimental results will be compared to theoretical results from a detailed 1-D computer model of the spatio-temporal evolution of the plasma kinetics and Xe species population densities. ^1R.P.Mildren and R.J.Carman, J.Phys.D, 34, L1-L6, (2001)

  11. Nonthermal Biological Treatments Using Discharge Plasma Produced by Pulsed Power 5. Inactivation of Cryptosporidium Oocysts by UV Emission Generated from Pulsed Arc Discharge in Water

    Science.gov (United States)

    Kunitomo, Shinta

    Cryptosporidium contaminates most surface waters around the world. It is difficult to remove through conventional treatment processes, and is extremely resistant to the method of chemical disinfection typically used to inactivate these microorganisms. We have developed a new technology for inactivating Cryptosporidium oocysts by using a pulsed arc discharge in water, which creates shock waves, UV emissions, and radicals. The pulsed arc is generated between two cylindrical stainless steel rod electrodes, 6 mm in diameter, and 2 mm apart. We applied this method to the inactivation of oocysts in backwash water from a sand-filter unit of a drinking water plant. The results indicate that the major factor influencing inactivation is UV emissions, and that more than 99% of the oocysts in the high turbidity backwash water (80 NTU) are inactivated with an energy of 0.24 kWh/m3.

  12. Investigation of nanosecond-pulsed dielectric barrier discharge actuators with powered electrodes of different exposures

    Science.gov (United States)

    Xu, Shuangyan; Cai, Jinsheng; Lian, Yongsheng

    2017-09-01

    Nanosecond-pulsed dielectric barrier discharge actuators with powered electrodes of different exposures were investigated numerically by using a newly proposed plasma kinetic model. The governing equations include the coupled continuity plasma discharge equation, drift-diffusion equation, electron energy equation, Poisson’s equation, and the Navier-Stokes equations. Powered electrodes of three different exposures were simulated to understand the effect of surface exposure on plasma discharge and surrounding flow field. Our study showed that the fully exposed powered electrode resulted in earlier reduced electric field breakdown and more intensive discharge characteristics than partially exposed and rounded-exposed ones. Our study also showed that the reduced electric field and heat release concentrated near the right upper tip of the powered electrode. The fully exposed electrode also led to stronger shock wave, higher heating temperature, and larger heated area.

  13. Signal enhancement in laser-induced breakdown spectroscopy using fast square-pulse discharges

    Science.gov (United States)

    Sobral, H.; Robledo-Martinez, A.

    2016-10-01

    A fast, high voltage square-shaped electrical pulse initiated by laser ablation was investigated as a means to enhance the analytical capabilities of laser Induced breakdown spectroscopy (LIBS). The electrical pulse is generated by the discharge of a charged coaxial cable into a matching impedance. The pulse duration and the stored charge are determined by the length of the cable. The ablation plasma was produced by hitting an aluminum target with a nanosecond 532-nm Nd:YAG laser beam under variable fluence 1.8-900 J cm- 2. An enhancement of up to one order of magnitude on the emission signal-to-noise ratio can be achieved with the spark discharge assisted laser ablation. Besides, this increment is larger for ionized species than for neutrals. LIBS signal is also increased with the discharge voltage with a tendency to saturate for high laser fluences. Electron density and temperature evolutions were determined from time delays of 100 ns after laser ablation plasma onset. Results suggest that the spark discharge mainly re-excites the laser produced plume.

  14. Pulsed picosecond and nanosecond discharge development in liquids with various dielectric permittivity constants

    Science.gov (United States)

    Starikovskiy, Andrey

    2016-09-01

    The dynamics of pulsed picosecond and nanosecond discharge development in liquid water, ethanol and hexane were investigated experimentally. It is shown that the dynamics of discharge formation fundamentally differ between liquids with low and high dielectric permittivity coefficients. The difference in the nanosecond discharge development in liquid dielectrics may be explained by the formation of micro-discontinuities in the media during the electrostriction compression/rarefaction stage in liquids with high dielectric permittivity. Three possible mechanisms for the propagation of discharge in liquids play a different role depending on the pulse duration. The first is the formation of low density channels in liquid. In the second case the electrostatic forces support the expansion of nanoscale voids behind the front of the ionization wave; in the wave front the extreme electric field provides a strong negative pressure in the dielectric fluid due to the presence of electrostriction forces, forming the initial micro-voids in the continuous medium. Finally, in the third case, when a picosecond electric pulse is utilized, the ionization in the liquid phase occurs as a result of direct electron impact without undergoing a phase transition.

  15. High-voltage nanosecond pulses in a low-pressure radiofrequency discharge

    CERN Document Server

    Pustylnik, Mikhail; Ivlev, Alexei; Vasilyak, Leonid; Couëdel, Lenaic; Thomas, Hubertus; Morfill, Gregor; Fortov, Vladimir

    2013-01-01

    An influence of a high-voltage (3-17 kV) 20 ns pulse on a weakly-ionized low-pressure (0.1-10 Pa) capacitively-coupled radiofrequency (RF) argon plasma is studied experimentally. The plasma evolution after pulse exhibits two characteristic regimes: a bright flash, occurring within 100 ns after the pulse (when the discharge emission increases by 2-3 orders of magnitude over the steady-state level), and a dark phase, lasting a few hundreds \\mu s (when the intensity of the discharge emission drops significantly below the steady-state level). The electron density increases during the flash and remains very large at the dark phase. 1D3V particle-in-cell simulations qualitatively reproduce both regimes and allow for detailed analysis of the underlying mechanisms. It is found that the high-voltage nanosecond pulse is capable of removing a significant fraction of plasma electrons out of the discharge gap, and that the flash is the result of the excitation of gas atoms, triggered by residual electrons accelerated in t...

  16. A Comparison of AC and Short-Pulse Excitation for Xe Excimer Barrier Discharge Lamps

    Science.gov (United States)

    Mildren, R. P.; Morrow, R.; Carman, R. J.

    1999-10-01

    Dielectric barrier discharge excitation of rare-gas and rare-gas halide excimers provides an efficient scheme for generating intense VUV radiation for applications including lighting, ozonisation, and photochemical surface treatment. Typically, lamps employ AC (sinusoidal) voltage excitation in which case VUV emission is produced from short-livid micro discharges (streamers) distributed stochastically over the dielectric. However, it has been recently demonstrated that significantly increased efficiency (by factor 2-3) can be obtained from Xe lamps when using short excitation pulses separated by idle periods[1]. In this paper, we report an investigation into the mechanisms which bring about improved efficiency by comparing the electrical, spectral and spatial emission characteristics of a small-scale Xe lamp excited by short pulses ( 100ns) with that of conventional AC excitation. The results reveal that pulsed excitation produces a homogenous glow-like discharge in which the electron density and temperature are more favourable for efficient excimer production. [1] RP Mildren et al, IVth Int. Conf. Atom. and Molec. Pulsed Lasers, Tomsk, Siberia Sept. (1999); F Vollkommer and L Hitzschke, Proc. 8th Int. Symp. Sci. Tech. Light Sources, Greifswald, Germany, '98, IL-07, pp51-59 (1998)

  17. Analytical solution for the diffusion of a capacitor discharge generated magnetic field pulse in a conductor

    Directory of Open Access Journals (Sweden)

    Ilmārs Grants

    2016-06-01

    Full Text Available Powerful forces arise when a pulse of a magnetic field in the order of a few tesla diffuses into a conductor. Such pulses are used in electromagnetic forming, impact welding of dissimilar materials and grain refinement of solidifying alloys. Strong magnetic field pulses are generated by the discharge current of a capacitor bank. We consider analytically the penetration of such pulse into a conducting half-space. Besides the exact solution we obtain two simple self-similar approximate solutions for two sequential stages of the initial transient. Furthermore, a general solution is provided for the external field given as a power series of time. Each term of this solution represents a self-similar function for which we obtain an explicit expression. The validity range of various approximate analytical solutions is evaluated by comparison to the exact solution.

  18. Analytical solution for the diffusion of a capacitor discharge generated magnetic field pulse in a conductor

    Science.gov (United States)

    Grants, Ilmārs; Bojarevičs, Andris; Gerbeth, Gunter

    2016-06-01

    Powerful forces arise when a pulse of a magnetic field in the order of a few tesla diffuses into a conductor. Such pulses are used in electromagnetic forming, impact welding of dissimilar materials and grain refinement of solidifying alloys. Strong magnetic field pulses are generated by the discharge current of a capacitor bank. We consider analytically the penetration of such pulse into a conducting half-space. Besides the exact solution we obtain two simple self-similar approximate solutions for two sequential stages of the initial transient. Furthermore, a general solution is provided for the external field given as a power series of time. Each term of this solution represents a self-similar function for which we obtain an explicit expression. The validity range of various approximate analytical solutions is evaluated by comparison to the exact solution.

  19. Efficiency of pulse-mode dielectric barrier discharge excimer lamp in constant duty cycle

    Science.gov (United States)

    Akashi, Haruaki; Oda, Akinori; Sakai, Yosuke

    2008-10-01

    Efficiency of pulse-mode dielectric barrier discharge (DBD) excimer lamp under constant duty cycle with increasing applied voltage has been simulated using two dimensional fluid model[1]. Xe gas with 300Torr pressure is assumed. And the simulated region considered in this model is 1cm(gap length)x3cm(radial length). Periodical boundary conditions are assumed for the radial direction boundaries. The both electrodes are covered with dielectrics and their thickness is 0.2cm. 5˜8kV trapezoid shape voltage is applied with the same voltage rising ratio and 50% duty ratio waveform with 200x10^3pps repetition rate. The discharge occurs at the rising edge and tailing edge of applied voltage. 172nm VUV intensity obtained from first discharge is higher than second one in lower applied voltage (<6kV) case. And in higher voltage case, the intensity from second discharge becomes higher. This is explained by shortening of interval time between the discharges. The short interval time makes higher initial electron density for second discharge. As a results, the input and 172nm VUV output power increases with increasing applied voltage, but the efficiency decreases. Because of inefficient surface discharge [1]H. Akashi et al, IEEE Trans. Plasma Science, Vol.33,No.2(2005,4)pp.308-309

  20. Application of nanosecond-pulsed dielectric barrier discharge for biomedical treatment of topographically non-uniform surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Ayan, H; Staack, D; Mukhin, Y; Starikovskii, A; Fridman, A [Department of Mechanical Engineering and Mechanics, College of Engineering, Drexel University, Philadelphia, PA 19104 (United States); Fridman, G [School of Biomedical Engineering, Science, and Health Systems, Drexel University, Philadelphia, PA 19104 (United States); Gutsol, A [Chevron Energy Technology Company, Richmond, CA 94802 (United States); Friedman, G [Department of Electrical and Computer Engineering, College of Engineering, Drexel University, Philadelphia, PA 19104 (United States)

    2009-06-21

    Antimicrobial effectiveness of a nanosecond-pulsed dielectric barrier discharge (DBD) was investigated and compared with that of a microsecond-pulsed DBD. Experiments were conducted on the Escherichia coli bacteria covering a topographically non-uniform agar surface acting as one of the DBD electrodes. They reveal that the nanosecond-pulsed DBD can inactivate bacteria in recessed areas whereas the microsecond-pulsed and conventional DBDs fail to do so. Charged species (electrons and ions) appear to play the major role in the bacteria inactivation with the nanosecond-pulsed DBD. Moreover, the nanosecond-pulsed DBD kills bacteria significantly faster than its microsecond-pulsed counterpart.

  1. Effect of Frequency on Emission of XeIast Excimer in a Pulsed Dielectric Barrier Discharge

    Science.gov (United States)

    Ou, Qiong-Rong; Meng, Yue-Dong; Xu, Xu; Shu, Xing-Sheng; Ren, Zhao-Xing

    2004-07-01

    Emission spectra of XeIast excimers and ultraviolet intensity at 253 nm from a dielectric barrier discharge (DBD) lamp excited by a pulsed voltage were measured as functions of pressure, electrical power, and frequency. In the DBD lamp driven by a higher frequency voltage, a more intense emission of XeIast excimers with high efficiency at 253 nm was found. A diffuse discharge mode was observed at high xenon pressure (>1 atm) with an excessive iodine concentration in the DBD driven by a high frequency (60 kHz) voltage.

  2. Effect of Frequency on Emission of XeI* Excimer in a Pulsed Dielectric Barrier Discharge

    Institute of Scientific and Technical Information of China (English)

    OU Qiong-Rong; MENG Yue-Dong; XU Xu; SHU Xing-Sheng; REN Zhao-Xing

    2004-01-01

    Emission spectra of XeI* excimers and ultraviolet intensity at 253 nm from a dielectric barrier discharge (DBD)lamp excited by a pulsed voltage were measured as functions of pressure, electrical power, and frequency. In the DBD lamp driven by a higher frequency voltage, a more intense emission of XeI* excimers with high efficiency at 253 nm was found. A diffuse discharge mode was observed at high xenon pressure (> 1 atm) with an excessive iodine concentration in the DBD driven by a high frequency (60 kHz) voltage.

  3. Study on the Microsecond Pulse Homogeneous Dielectric Barrier Discharges in Atmospheric Air and Its Influencing Factors%Study on the Microsecond Pulse Homogeneous Dielectric Barrier Discharges in Atmospheric Air and Its Influencing Factors

    Institute of Scientific and Technical Information of China (English)

    方志; 雷枭; 蔡玲玲; 邱毓昌; Edmund KUFFEL

    2011-01-01

    The homogeneous dielectric barrier discharge (DBD) in atmospheric air between two symmetric-columnar copper electrodes with epoxy plates as the dielectric barriers is generated using a us pulse high voltage power supply. The discharge characteristics are studied by measurement of its electrical discharge parameters and observation of its light emission phenom- ena, and the main discharge parameters of the homogenous DBD, such as discharge current and average discharge power, are calculated. Results show that the discharge generated is a homogeneous one with one larger single current pulse of about 2 #s duration appearing in each voltage pulse, and its light emission is radially homogeneous and covers the entire surface of the two elec- trodes. The influences of applied voltage amplitude, air gap distance and barrier thickness on the transition of discharge modes are studied. With the increase of air gap distance, the discharge will transit from homogeneous mode to filamentary mode. The higher the thickness of dielectric barriers, the larger the air gap distance for generating the homogeneous discharge mode. The average discharge power increases non-linearly with increasing applied voltage amplitude, and decreases non-linearly with the increase of air gap distance and barrier thickness. In order to generate stable and homogeneous DBD with high discharge power, thin barriers distance should be used, and higher applied voltage amplitude should be applied to small air gap.

  4. The role of high Rydberg states in enhanced O- formation in a pulsed O2 discharge

    Science.gov (United States)

    Ding, W. X.; Pinnaduwage, L. A.; Tav, C.; McCorkle, D. L.

    1999-08-01

    Formation of O- ions in a pulsed discharge of O2 was investigated in a Langmuir-probe-assisted photodetachment experiment. A large enhancement of negative ion formation was observed in the afterglow. Experimental results are consistent with O- formation via electron attachment to high Rydberg states of O2 that survive into the afterglow. Such excited states can be produced by high-energy electron impact during the discharge. The lifetime of high-Rydberg molecules is estimated to be longer than 10 microseconds. The efficient production of O- ion by electron attachment to high-Rydberg O2 molecules was further confirmed in a laser excitation experiment. The O- ions and O atoms produced via enhanced dissociative electron attachment to excited states of O2 may be important for the chemical processes that occur in pulsed plasma remediation of contaminated air.

  5. Inactivation of Bacteria in Oil Field Injected Water by a Pulsed Plasma Discharge Process

    Science.gov (United States)

    Xin, Qing; Li, Zhongjian; Lei, Lecheng; Yang, Bin

    2016-09-01

    Pulsed plasma discharge was employed to inactivate bacteria in the injection water for an oil field. The effects of water conductivity and initial concentration of bacteria on elimination efficiency were investigated in the batch and continuous flow modes. It was demonstrated that Fe2+ contained in injection water could enhance the elimination efficiency greatly. The addition of reducing agent glutathione (GSH) indicated that active radicals generated by pulsed plasma discharges played an important role in the inactivation of bacteria. Moreover, it was found that the microbial inactivation process for both batch and continuous flow mode well fitted the model based on the Weibull's survival function. supported by Zhejiang Province Welfare Technology Applied Research Project of China (No. 2014C31137), National Natural Science Foundation of China (Nos. 21436007 and U1462201), and the Fundamental Research Funds for the Central Universities of China (No. 2015QNA4032)

  6. Time-resolved electron density and electron temperature measurements in nanosecond pulse discharges in helium

    Science.gov (United States)

    Roettgen, A.; Shkurenkov, I.; Simeni Simeni, M.; Petrishchev, V.; Adamovich, I. V.; Lempert, W. R.

    2016-10-01

    Thomson scattering is used to study temporal evolution of electron density and electron temperature in nanosecond pulse discharges in helium sustained in two different configurations, (i) diffuse filament discharge between two spherical electrodes, and (ii) surface discharge over plane quartz surface. In the diffuse filament discharge, the experimental results are compared with the predictions of a 2D plasma fluid model. Electron densities are put on an absolute scale using pure rotational Raman spectra in nitrogen, taken without the plasma, for calibration. In the diffuse filament discharge, electron density and electron temperature increase rapidly after breakdown, peaking at n e  ≈  3.5 · 1015 cm-3 and T e  ≈  4.0 eV. After the primary discharge pulse, both electron density and electron temperature decrease (to n e ~ 1014 cm-3 over ~1 µs and to T e ~ 0.5 eV over ~200 ns), with a brief transient rise produced by the secondary discharge pulse. At the present conditions, the dominant recombination mechanism is dissociative recombination of electrons with molecular ions, \\text{He}2+ . In the afterglow, the electron temperature does not relax to gas temperature, due to superelastic collisions. Electron energy distribution functions (EEDFs) inferred from the Thomson scattering spectra are nearly Maxwellian, which is expected at high ionization fractions, when the shape of EEDF is controlled primarily by electron-electron collisions. The kinetic model predictions agree well with the temporal trends detected in the experiment, although peak electron temperature and electron density are overpredicted. Heavy species temperature predicted during the discharge and the early afterglow remains low and does not exceed T  =  400 K, due to relatively slow quenching of metastable He* atoms in two-body and three-body processes. In the surface discharge, peak electron density and electron temperature are n e  ≈  3 · 1014 cm3 and T e

  7. Experimental studies of the formation of cluster ions formed by corona discharge in an atmosphere containing SO2, NH3, and H2O

    Science.gov (United States)

    Pedersen, J. O.; Hvelplund, P.; Støchkel, K.; Enghoff, M. B.; Kurten, T.

    2013-12-01

    We report on studies of ion induced nucleation in a corona discharge taking place in an atmosphere containing SO2, NH3, and H2O at standard temperature and pressure. Positive ions such as H3O+(H2O)n, NH4+(H2O)n, and H+(H2SO4)(H2O)n and negative ions such as HSO5-(H2O)n, SO4-(H2O)n, HSO4-(H2O)n and NO3-(H2O)n have been recorded. Large values of n (> 100) were observed and the experiment indicates the existence of even larger water clusters. In contrast, only clusters with a maximum of 2 sulfuric acid molecules were observed. Fragmentation studies also revealed that the negative ion HSO5-, which has been observed in many studies, in our experiments is contaminated by O2-(HNO3)(H2O) ions, and this may also have been the case in other experiments. Finally an ion with m/z = 232 (where m is the cluster mass in amu and z the charge state), capable of attaching H2O-molecules was observed and studied by fragmentation. Positive ion m/z (mass/charge) spectrum

  8. Detection of Amines and Ammonia with an Ambient Pressure Mass Spectrometer using a Corona Discharge Ion Source, in an Urban Atmosphere and in a Teflon Film Chamber

    Science.gov (United States)

    Alves, M.; Hanson, D. R.; Grieves, C.; Ortega, J. V.

    2015-12-01

    Amines and ammonia are an important group of molecules that can greatly affect atmospheric particle formation that can go on to impact cloud formation and their scattering of thermal and solar radiation, and as a result human health and ecosystems. In this study, an Ambient Pressure Mass Spectrometer (AmPMS) that is selective and sensitive to molecules with a high proton affinity, such as amines, was coupled with a newly built corona discharge ion source. AmPMS was used to monitor many different nitrogenous compound that are found in an urban atmosphere (July 2015, Minneapolis), down to the single digit pmol/mol level. Simultaneous to this, a proton transfer mass spectrometer also sampled the atmosphere through an inlet within 20 m of the AmPMS inlet. In another set of studies, a similar AmPMS was attached to a large Teflon film chamber at the Atmospheric Chemistry Division at NCAR (August 2015, Boulder). Exploratory studies are planned on the sticking of amines to the chamber walls as well as oxidizing the amine and monitoring products. Depending on the success of these studies, results will be presented on the reversability of amine partitioning and mass balance for these species in the chamber.

  9. Effects of H3O+, OH-, \\text{O}_{2}^{-} , \\text{NO}_{\\text{x}}^{-} and NO x for Escherichia coli inactivation in atmospheric pressure DC corona discharges

    Science.gov (United States)

    Sekimoto, Kanako; Gonda, Rena; Takayama, Mitsuo

    2015-08-01

    The effects of ionic and neutral species such as H3O+, OH-, \\text{O}2- , \\text{NO}x- (x = 2, 3), and NO x on Escherichia coli (E. coli) inactivation in gas and liquid phases was investigated using atmospheric pressure DC corona discharges with point-to-plane electrodes. The above chemical species as well as OH and O3 were selectively irradiated onto E. coli suspensions on agar plates using a needle angle of 45° with respect to the plates, airflow, and a grid plate. Irradiation with the positive ion H3O+ did not inactivate E. coli, while the negative ions OH-/\\text{O}2- resulted in bactericidal inactivation, in both gas and liquid phases. In contrast, the negative ions \\text{NO}x- and neutral species NO x in the gas phase had quite strong bactericidal effects on E. coli compared to those species in the liquid phase. These results suggest that liquid-phase HNO3, formed primarily via the reaction of gas-phase \\text{NO}x- and NO x with H2O in agar, has only a weak inactivation effect on E. coli. Furthermore, using naphthylethylenediamine spectrophotometry, the threshold amount of gas-phase \\text{NO}x- and NO x for E. coli inactivation was determined to be  ≈1.3   ×   10-9 mol mm-1.

  10. Influence of corona discharge on the ozone budget in the tropical free troposphere: a case study of deep convection during GABRIEL

    Science.gov (United States)

    Bozem, H.; Fischer, H.; Gurk, C.; Schiller, C. L.; Parchatka, U.; Koenigstedt, R.; Stickler, A.; Martinez, M.; Harder, H.; Kubistin, D.; Williams, J.; Eerdekens, G.; Lelieveld, J.

    2014-09-01

    Convective redistribution of ozone and its precursors between the boundary layer (BL) and the free troposphere (FT) influences photochemistry, in particular in the middle and upper troposphere (UT). We present a case study of convective transport during the GABRIEL campaign over the tropical rain forest in Suriname in October 2005. During one measurement flight the inflow and outflow regions of a cumulonimbus cloud (Cb) have been characterized. We identified a distinct layer between 9 and 11 km altitude with enhanced mixing ratios of CO, O3, HOx, acetone and acetonitrile. The elevated O3 contradicts the expectation that convective transport brings low-ozone air from the boundary layer to the outflow region. Entrainment of ozone-rich air is estimated to account for 62% (range: 33-91%) of the observed O3. Ozone is enhanced by only 5-6% by photochemical production in the outflow due to enhanced NO from lightning, based on model calculations using observations including the first reported HOx measurements over the tropical rainforest. The "excess" ozone in the outflow is most probably due to direct production by corona discharge associated with lightning. We deduce a production rate of 5.12 × 1028 molecules O3 flash-1 (range: 9.89 × 1026-9.82 × 1028 molecules O3 flash-1), which is at the upper limit of the range reported previously.

  11. Cavity Ignition in Supersonic Flow by Spark Discharge and Pulse Detonation

    Science.gov (United States)

    2014-08-18

    constant volume, through a detonation , or some combination. While a deflagration (flame) through constant volume combustion can provide rapid heat release...significantly disrupted, and the detonation was able to ignite and burn most of the fuel within the cavity. This led to decreased heat release in regime IV...locate/proci of the Combustion InstituteCavity ignition in supersonic flow by spark discharge and pulse detonation Timothy M. Ombrello a,⇑, Campbell D

  12. Nanosecond pulsed sliding dielectric barrier discharge plasma actuator for airflow control: Electrical, optical, and mechanical characteristics

    Science.gov (United States)

    Bayoda, K. D.; Benard, N.; Moreau, E.

    2015-08-01

    Plasma actuators used for active flow control are widely studied because they could replace mechanical actuators. Industrial applications of these plasma actuators sometimes require a large surface plasma sheet in view of increasing the interaction region between the discharge and the incoming flow. Instead of using a typical two-electrode nanosecond pulsed dielectric barrier discharge for which the interaction region is limited to about 20 mm, this study proposes to characterize a nanosecond sliding discharge based on a three-electrode geometry in order to increase the extension length up to the electrode gap. This sliding discharge is compared to the typical nanosecond dielectric barrier discharge by means of electrical, optical, and mechanical diagnostics. Electrical characterization reveals that the deposited energy can be widely increased. Time-resolved Intensified Charge Coupled Device (iCCD) images of the discharge development over the dielectric surface highlight that the intensity and the propagation velocity of streamers are strongly affected by the DC voltage applied at the third electrode. Finally, qualitative and quantitative characterizations of the pressure wave due to the surrounding gas heating are proposed by means of Schlieren visualizations and high frequency pressure measurements, respectively.

  13. Modeling of dielectric barrier discharge excimer lamp excited by mono polar voltage pulses

    Science.gov (United States)

    Akashi, Haruaki; Oda, Akinori; Sakai, Yosuke

    2007-10-01

    Filametal discharges in Dielectric Barrier Discharge (DBD) excimer lamp excited by mono polar voltage pulses has been simulated using two dimensional fluid model. And the differences of the filament discharges formations between mono polar case and bipolar case [1] have been examined. Xe gas was used and its pressure is 300Torr. Simulated region is 1cm (gap length) x 3cm (radial length). Periodical boundary conditions are assumed for the radial direction boundaries. The both electrodes are covered with dielectrics and their thickness is 0.2cm. Applied voltage is 5kV trapezoid shape with 50% duty ratio waveform and its repetition rate is 200kpps. First a small amount of electron-ion pair is provided in the middle of the gap for initial condition. Then the voltage starts to apply. In the case of bipolar excitation, the discharge starts from one filament (streamer discharge), and finally, 5 filaments are obtained self-consistently. In the case of mono polar case, as first, similar to bipolar case, the discharge starts from one filament, however, only 3 filaments have been obtained. This result is similar to that of 100kHz bipolar voltage case. [1] H. Akashi et al, IEEE Trans. Plasma Science, Vol.33, No.2 (2005) pp.308-309

  14. Spectroscopic diagnostics of a pulsed discharge in high-pressure argon

    Science.gov (United States)

    Treshchalov, A. B.; Lissovskii, A. A.

    2010-05-01

    Results of investigation of high-pressure argon plasma excited by a high-current pulsed volume discharge are presented. The plasma diagnostics employs spatiotemporal dependences of the emission intensity in the VUV — visible range. A homogenous discharge is observed at pressures up to 10 atm. It is found that the spectrum of the UV — visible photorecombination continuum is sensitive to the discharge constriction. Change in the shape of the spectrum is caused bythe change of the type of positive charge carriers upon passing of the discharge from the uniform phase (molecular Ar2+ ions) to the arc phase (atomic Ar+ ions). Experimental data and model calculations show that the electron heating after the main excitation pulse is a highly undesirable process. It slows down the recombination flow in the plasma, which results in stretching of all the kinetic processes for all excited components in time, and hence in a decrease in the peak values of their concentrations. Electron collision-induced mixing effi-ciently converts the reservoir of long-lived Ar2* molecules in the triplet state into rapidly emitting singlet excimers. It is this mechanism that dominates the production of singlet Ar2* excimer molecules. The threshold concentration needed to obtain lasing at a wavelength of 127 nm on Ar2* excimers (1Σ+u(v=0)) was, according to calculations, about 5×1015 cm-3 for the gain 0.05 cm-1. This concentration can be achieved in the case of homogeneous pulsed discharge pumping with the peak electron concentration 2.×1016 cm-3 at the argon pressure 10 atm.

  15. VUV-VIS spectroscopic diagnostics of a pulsed high-pressure discharge in argon

    Science.gov (United States)

    Treshchalov, A. B.; Lissovski, A. A.

    2009-12-01

    High-pressure argon plasma, excited by a high-current pulsed volume discharge, has been investigated. Spatial-time VUV-VIS emission kinetics were used for the plasma diagnostics. A homogeneous discharge was obtained at a pressure of up to 10 bar. It was revealed that the spectral shape of the UV-VIS photorecombination continuum is a sensitive diagnostic tool for the constriction of the discharge. This shape changes because of the difference of the positive charge carriers in the arc (atomic Ar+ ions) and homogeneous (molecular Ar_{2}^{+} ions) phases of the discharge. The intensity of this continuum is proportional to the square of the electron density. The experimental data and modelling show that the heating of electrons after the main excitation pulse is a very undesirable process. It suppresses the recombination flow in plasma, thus the kinetics of all excited species are spread in time with a decrease in the Ar_{2}^{\\ast } excimers densities. The electron collision-induced mixing effectively converts the reservoir of long-lived triplet Ar_{2}^{\\ast } molecules to fast-emitted singlet excimers. This mechanism is dominant in the production of singlet excimers. A realistic threshold density for the lasing of Ar_2^{\\ast}({{}^{1}\\Sigma_u})_{(v=0)} excimers of about 5 × 1015 cm-3 was estimated (the gain coefficient is 0.05 cm-1). This criterion could be realized in 10 bar of Ar by a homogeneous single pulse discharge pumping with a peak electron density of 2.4 × 1016 cm-3.

  16. Ion energy distributions in bipolar pulsed-dc discharges of methane measured at the biased cathode

    Energy Technology Data Exchange (ETDEWEB)

    Corbella, C; Rubio-Roy, M; Bertran, E; Portal, S; Pascual, E; Polo, M C; Andujar, J L, E-mail: corbella@ub.edu [FEMAN Group, IN2UB, Departament de Fisica Aplicada i Optica, Universitat de Barcelona, c/ MartI i Franques 1, 08028 Barcelona (Spain)

    2011-02-15

    The ion fluxes and ion energy distributions (IED) corresponding to discharges in methane (CH{sub 4}) were measured in time-averaged mode with a compact retarding field energy analyser (RFEA). The RFEA was placed on a biased electrode at room temperature, which was powered by either radiofrequency (13.56 MHz) or asymmetric bipolar pulsed-dc (250 kHz) signals. The shape of the resulting IED showed the relevant populations of ions bombarding the cathode at discharge parameters typical in the material processing technology: working pressures ranging from 1 to 10 Pa and cathode bias voltages between 100 and 200 V. High-energy peaks in the IED were detected at low pressures, whereas low-energy populations became progressively dominant at higher pressures. This effect is attributed to the transition from collisionless to collisional regimes of the cathode sheath as the pressure increases. On the other hand, pulsed-dc plasmas showed broader IED than RF discharges. This fact is connected to the different working frequencies and the intense peak voltages (up to 450 V) driven by the pulsed power supply. This work improves our understanding in plasma processes at the cathode level, which are of crucial importance for the growth and processing of materials requiring controlled ion bombardment. Examples of industrial applications with these requirements are plasma cleaning, ion etching processes during fabrication of microelectronic devices and plasma-enhanced chemical vapour deposition of hard coatings (diamond-like carbon, carbides and nitrides).

  17. High-pressure pulsed avalanche discharges: Formulas for required preionization density and rate for homogeneity

    Energy Technology Data Exchange (ETDEWEB)

    Brenning, N.; Axnaes, I.; Nilsson, J.O.; Eninger, J.E. [Royal Inst. of Tech., Stockholm (Sweden)

    1997-02-01

    The requirements on preionization for the formation of spatially homogeneous pulsed avalanche discharges are examined. The authors derive two formulas which apply in the case of a slowly rising electric field, one which gives the required preionization density at breakdown, and one which gives the required preionization rate. These quantities are expressed as functions of the electrochemical properties of the gas, the neutral density, and the electric field rise time. They also treat the statistical effect that the electrons tend to form groups, in contrast to being randomly distributed in space, during the prebreakdown phase. This process is found to increase the required preionization rate significantly, typically by a factor of five for a discharge at atmospheric pressure. Homogeneous high-pressure discharges have been used for laser excitation, and have also been proposed for chemical plasma processing (ozone production) because of their good scaling properties and high efficiency.

  18. Self-Consistent Model for Pulsed Direct-Current N2 Glow Discharge

    Institute of Scientific and Technical Information of China (English)

    Liu Chengsen; Wang Dezhen

    2005-01-01

    A self-consistent analysis of a pulsed direct-current (DC) N2 glow discharge is presented. The model is based on a numerical solution of the continuity equations for electron and ions coupled with Poisson's equation. The spatial-temporal variations of ionic and electronic densities and electric field are obtained. The electric field structure exhibits all the characteristic regions of a typical glow discharge (the cathode fall, the negative glow, and the positive column).Current-voltage characteristics of the discharge can be obtained from the model. The calculated current-voltage results using a constant secondary electron emission coefficient for the gas pressure 133.32 Pa are in reasonable agreement with experiment.

  19. Nanosecond-timescale high-pressure gas discharge in a microwave pulse compressor

    Science.gov (United States)

    Shlapakovski, Anatoli; Beilin, Leonid; Krasik, Yakov

    2016-09-01

    The results of experimental and numerical studies of the microwave plasma discharge initiated by a nanosecond laser pulse are presented. The discharge is ignited in the pressurized gas filling the switch, which opens the charged resonant cavity, so that the accumulated microwave energy is rapidly released into a load. Fast-framing optical imaging showed that the plasma in the switch appears as filaments expanding along the RF electric field. The temporal evolution of the plasma density was derived from time-resolved spectroscopic measurements. With increasing microwave energy in the cavity, the plasma appears earlier in time after the laser beam enters the switch and its density rises more steeply reaching values which exceed 1016 cm-3 at a gas pressure of 2 .105 Pa. Numerical simulations were conducted using the gas conductivity model of plasma and representation of discharge origin by setting initial population of seed electrons treated by PIC algorithm. The results showed good agreement with the experiments and explained how the self-consistent dynamics of the plasma and RF fields determines the quality of microwave output pulses. In addition, the dynamics of the microwave energy absorption in the discharge plasma was studied. It was shown that at a high pressure, even with an unlimited rate of ionization, a significant portion of the stored energy, 20%, is lost. This work was partially supported by the BSF Grant No. 2012038.

  20. Dynamics of atomic kinetics in a pulsed positive-column discharge at 100 Pa

    Science.gov (United States)

    Franek, J. B.; Nogami, S. H.; Koepke, M. E.; Demidov, V. I.; Barnat, E. V.

    2017-01-01

    Temporal measurements of the electron density, metastable-atom density, and reduced electric field demonstrate that four orders of magnitude variation in the dynamic range of the electron-atom collision-induced excitation rates takes place during the 2.0 kV height, 40 µs duration repeating pulse applied to a 100 Pa (1 Torr), argon positive column in a hollow-cathode discharge. Correlation between metastable-atom density and emission-line ratio is demonstrated to be sufficiently reliable to infer one quantity based on the measurement of the other quantity during the Initiation, Transient, and Post-Transient spectroscopic stages of the pulse. Observed emission-line ratio and the predicted emission-line ratio are in quantitative agreement with each other in the Transient and Post-Transient stages of the discharge and are in qualitative agreement with each other in the Initiation stage of the discharge. Reasonable assumptions regarding the interpretation of the electron energy probability function (EEPF), as it starts off being Druyvesteyn and becomes more Maxwellian later with the increasing electron density, is key to interpreting the correlation and explaining the temporal behavior of the emission-line ratio in all stages of the discharge.

  1. Pulsed Discharge Effects on Bacteria Inactivation in Low-Pressure Radio-Frequency Oxygen Plasma

    Science.gov (United States)

    Vicoveanu, Dragos; Ohtsu, Yasunori; Fujita, Hiroharu

    2008-02-01

    The sporicidal effects of low-pressure radio frequency (RF) discharges in oxygen, produced by the application of continuous and pulsed RF power, were evaluated. For all cases, the survival curves showed a biphasic evolution. The maximum efficiency for bacteria sterilization was obtained when the RF power was injected in the continuous wave mode, while in the pulsed mode the lowest treatment temperature was ensured. The inactivation rates were calculated from the microorganism survival curves and their dependencies on the pulse characteristics (i.e., pulse frequency and duty cycle) were compared with those of the plasma parameters. The results indicated that the inactivation rate corresponding to the first phase of the survival curves is related to the time-averaged intensity of the light emission by the excited neutral atoms in the pulsed plasma, whereas the inactivation rate calculated from the second slope of the survival curves and the time-averaged plasma density have similar behaviors, when the pulse parameters were modified.

  2. Ionized sputter deposition using an extremely high plasma density pulsed magnetron discharge

    Energy Technology Data Exchange (ETDEWEB)

    Macak, Karol [Department of Physics, Linkoeping University, SE-581 83 Linkoeping, (Sweden); Kouznetsov, Vladimir [Department of Physics, Linkoeping University, SE-581 83 Linkoeping, (Sweden); Schneider, Jochen [Department of Physics, Linkoeping University, SE-581 83 Linkoeping, (Sweden); Helmersson, Ulf [Department of Physics, Linkoeping University, SE-581 83 Linkoeping, (Sweden); Petrov, Ivan [Materials Science Department and Materials Research Laboratory, University of Illinois, Urbana, Illinois 61801 (United States)

    2000-07-01

    Time resolved plasma probe measurements of a novel high power density pulsed plasma discharge are presented. Extreme peak power densities in the pulse (on the order of several kW cm{sup -2}) result in a very dense plasma with substrate ionic flux densities of up to 1 A cm{sup -2} at source-to-substrate distances of several cm and at a pressure of 0.13 Pa (1 mTorr). The pulse duration was {approx}100 {mu}s with a pulse repetition frequency of 50 Hz. The plasma consists of metallic and inert gas ions, as determined from time resolved Langmuir probe measurements and in situ optical emission spectroscopy data. It was found that the plasma composition at the beginning of the pulse was dominated by Ar ions. As time elapsed metal ions were detected and finally dominated the ion composition. The effect of the process parameters on the temporal development of the ionic fluxes is discussed. The ionized portion of the sputtered metal flux was found to have an average velocity of 2500 m s{sup -1} at 6 cm distance from the source, which conforms to the collisional cascade sputtering theory. The degree of ionization of the sputtered metal flux at a pressure of 0.13 Pa was found to be 40%{+-}20% by comparing the total flux of deposited atoms with the charge measured for the metal ions in the pulse. (c) 2000 American Vacuum Society.

  3. Streamer-to-spark transition initiated by a nanosecond overvoltage pulsed discharge in air

    Science.gov (United States)

    Lo, A.; Cessou, A.; Lacour, C.; Lecordier, B.; Boubert, P.; Xu, D. A.; Laux, C. O.; Vervisch, P.

    2017-04-01

    This study is focused on the streamer-to-spark transition generated by an overvoltage nanosecond pulsed discharge under atmospheric pressure air in order to provide a quantitative insight into plasma-assisted ignition. The discharge is generated in atmospheric pressure air by the application of a positive high voltage pulse of 35 kV to pin-to-pin electrodes and a rise time of 5 ns. The generated discharge consists of a streamer phase with high voltage and high current followed by a spark phase characterized by a low voltage and a decreasing current in several hundreds of nanosecond. During the streamer phase, the gas temperature measured by optical emission spectroscopy related to the second positive system of nitrogen shows an ultra-fast gas heating up to 1200 K at 15 ns after the current rise. This ultra-fast gas heating, due to the quenching of electronically excited species by oxygen molecules, is followed by a quick dissociation of molecules and then the discharge transition to a spark. At this transition, the discharge contracts toward the channel axis and evolves into a highly conducting thin column. The spark phase is characterized by a high degree of ionization of nitrogen and oxygen atoms shown by the electron number density and temperature measured from optical emission spectroscopy measurements of N+ lines. Schlieren imaging and optical emission spectroscopy techniques provide the time evolution of the spark radius, from which the initial pressure in the spark is estimated. The expansion of the plasma is adiabatic in the early phase. The electronic temperature and density during this phase allows the determination of the isentropic coefficient. The value around 1.2-1.3 is coherent with the high ionization rate of the plasma in the early phase. The results obtained in this study provide a database and the initial conditions for the validation of numerical simulations of the ignition by plasma discharge.

  4. Nanosecond pulsed dielectric barrier discharge plasma-catalytic removal of HCHO in humid air

    Science.gov (United States)

    Zhang, Shuai; Wang, Wenchun; Zhang, Li; Zhao, Zilu; Yang, Dezheng

    2017-05-01

    Non-thermal plasma (NTP) has been regarded as a promising method for the removal of a wide range of low concentration volatile organic compounds (VOCs). In this paper, nanosecond pulsed and alternating current dielectric barrier discharge plasmas synergistic catalyst are utilized for removal of formaldehyde (HCHO) in humid air. Working gas is 1% H2O/21% O2/78% N2 with 154 ppm HCHO over total flow rate of 50 mL/min. Specific energy density (SED) are 32.5 JL-1, 35.8 JL-1 and 1069.2 JL-1 at power consumption of 0.325 W, 0.3 W, 8.9 W for removal of 67%, 63.8% and 73.8% HCHO when using bipolar nanosecond pulsed, unipolar nanosecond pulsed and AC dielectric barrier discharge (DBD) plasma, respectively. The removal efficiencies of HCHO using nanosecond pulsed DBD plasma increase approximately 10 20% when the packed-bed Al2O3 pellets exist and can reach up to almost 100% when TiO2 nanoparticles are used while the effect of CeO2 nanoparticles is a bit poor. Analysis indicate that OH radical and O atom play main role for removal HCHO and the gas temperature is a significant factor for its influence on rate constants of HCHO with active particles.

  5. Development of a long pulse plasma gun discharge for magnetic turbulence studies

    Science.gov (United States)

    Schaffner, David

    2016-10-01

    A long pulse ( 300 μs) plasma gun discharge is in development at the Bryn Mawr College Plasma Laboratory for the production of sustained magnetized plasma injection for magnetohydrodynamic (MHD) turbulence studies. An array of eight 0.5mF parallel capacitors are used to create a pulse-forming-network (PFN) with a plateaued current output of 50kA for at least 200 of the 300 μs pulse. A 24cm inner diameter plasma gun provides stuffing flux fields at the stuffing threshold in order to allow for the continuous injection of magnetic helicity. Plasma is injected into a 24cm diameter flux-conserving aluminum chamber with a high density port array for fine spatial resolution diagnostic access. Fluctuations of magnetic field and saturation current are measured using pickup probes and Langmuir probes respectively.

  6. Pulse, dc and ac breakdown in high pressure gas discharge lamps

    Science.gov (United States)

    Beckers, J.; Manders, F.; Aben, P. C. H.; Stoffels, W. W.; Haverlag, M.

    2008-07-01

    An optical study of pulse, dc, and ac (50-400 kHz) ignition of metal halide lamps has been performed by investigating intensified CCD camera images of the discharges. The ceramic lamp burners were filled with xenon gas at pressures of 300 and 700 mbar. In comparison with dc and pulse ignition, igniting with an ac voltage decreases the ignition voltage by up to 56% and the breakdown time scales get much longer (~10-3 s compared with ~10-7 s for pulse ignition). Increasing the ac frequency decreases the ignition voltages and changes the ionization channel shapes. External irradiation of UV light can have either an increasing or a decreasing effect on ignition voltages.

  7. Time-resolved temperature and O atom measurements in nanosecond pulse discharges in combustible mixtures

    Science.gov (United States)

    Lanier, Suzanne; Bowman, Sherrie; Burnette, David; Adamovich, Igor V.; Lempert, Walter R.

    2014-11-01

    The paper presents results of time-resolved rotational temperature measurements, by pure rotational coherent anti-Stokes Raman spectroscopy and absolute O atom number density measurements, by two-photon absorption laser induced fluorescence. The experiments were conducted in nanosecond pulse discharges in H2-O2-Ar and C2H4-O2-Ar mixtures, initially at room temperature, operated at a high pulse repetition rate of 40 kHz, in a plane-to-plane double dielectric barrier geometry at a pressure of 40 Torr. Intensified charge-coupled device images show that O2-Ar and H2-O2-Ar plasmas remain diffuse and volume-filling during the entire burst. Images taken in C2H4-O2-Ar plasma demonstrate significant discharge filamentation and constriction along the center plane and in the corners of the test section. The experimental results demonstrate high accuracy of pure rotational psec CARS for thermometry measurements at low partial pressures of oxygen in nonequilibrium plasmas. The results are compared with kinetic modeling calculations, using two different H2-O2 chemistry and C2H4-O2 chemistry mechanisms. In H2-O2-Ar mixtures, the kinetic modeling predictions are in fairly good agreement with the data, predicting temperature rise and O atom accumulation in long discharge bursts, up to 450 pulses. The results show that adding hydrogen to the mixture results in an additional temperature rise, due to its partial oxidation by radicals generated in the plasma, essentially without chain branching. In C2H4-O2-Ar mixtures, the model consistently underpredicts both temperature and O atom number density. The most likely reason for the difference between the experimental data and model predictions is discharge filamentation developing when ethylene is added to the O2-Ar mixture, at fairly low temperatures.

  8. Radiative heat transfer in plasma of pulsed high pressure caesium discharge

    Science.gov (United States)

    Lapshin, V. F.

    2016-01-01

    Two-temperature many component gas dynamic model is used for the analysis of features of radiative heat transfer in pulsed high pressure caesium discharge plasma. It is shown that at a sufficiently high pressure the radial optical thickness of arc column is close to unit (τR (λ) ∼ 1) in most part of spectrum. In this case radiative heat transfer has not local character. In these conditions the photons which are emitted in any point of plasma volume are absorbed in other point remote from an emission point on considerable distance. As a result, the most part of the electric energy put in the discharge mainly near its axis is almost instantly redistributed on all volume of discharge column. In such discharge radial profiles of temperature are smooth. In case of low pressure, when discharge plasma is optically transparent for own radiation in the most part of a spectrum (τR(λ) << 1), the emission of radiation without reabsorption takes place. Radiative heat transfer in plasma has local character and profiles of temperature have considerable gradient.

  9. Plasma processes in water under effect of short duration pulse discharges

    Science.gov (United States)

    Gurbanov, Elchin

    2013-09-01

    It is very important to get a clear water without any impurities and bacteria by methods, that don't change the physical and chemical indicators of water now. In this article the plasma processes during the water treatment by strong electric fields and short duration pulse discharges are considered. The crown discharge around an electrode with a small radius of curvature consists of plasma leader channels with a high conductivity, where the thermo ionization processes and UV-radiation are taken place. Simultaneously the partial discharges around potential electrode lead to formation of atomic oxygen and ozone. The spark discharge arises, when plasma leader channels cross the all interelectrode gap, where the temperature and pressure are strongly grown. As a result the shock waves and dispersing liquid streams in all discharge gap are formed. The plasma channels extend, pressure inside it becomes less than hydrostatic one and the collapse and UV-radiation processes are started. The considered physical processes can be successfully used as a basis for development of pilot-industrial installations for conditioning of drinking water and to disinfecting of sewage.

  10. Improvement of Spatial Uniformity of Nanosecond-Pulse Diffuse Discharges in a Multi-Needle-to-Plane Gap

    Science.gov (United States)

    Gu, Jianwei; Zhang, Cheng; Wang, Ruixue; Yan, Ping; Shao, Tao

    2016-03-01

    Large-scale non-thermal plasmas generated by nanosecond-pulse discharges have been used in various applications, including surface treatment, biomedical treatment, flow control etc. In this paper, atmospheric-pressure diffuse discharge was produced by a homemade nanosecond-pulse generator with a full width at half maximum of 100 ns and a rise time of 70 ns. In order to increase the discharge area, multi-needle electrodes with a 3×3 array were designed. The electrical characteristics of the diffuse discharge array and optical images were investigated by the voltage-current waveforms and discharge images. The experimental results showed that the intensity of diffuse discharges in the center was significantly weaker than those at the margins, resulting in an inhomogeneous spatial uniformity in the diffuse discharge array. Simulation of the electric field showed that the inhomogeneous spatial uniformity was caused by the non-uniform distribution of the electric field in the diffuse discharge array. Moreover, the spatial uniformity of the diffuse discharge array could be improved by increasing the length of the needle in the centre of the array. Finally, the experimental results confirmed the simulation results, and the spatial uniformity of the nanosecond-pulse diffuse discharge array was significantly improved. supported by National Natural Science Foundation of China (Nos. 51222701, 51477164) and the National Basic Research Program of China (No. 2014CB239505-3)

  11. Time-resolved analysis and optical diagnostics of Trichel corona in atmospheric air

    Science.gov (United States)

    Zhang, Yu; Qin, Yu; Zhao, Gao; Ouyang, Jiting

    2016-06-01

    Trichel pulses of negative corona discharge in atmospheric air are investigated in a needle-to-plate configuration. Time-resolved images of the pulsed discharge are recorded by using an ICCD camera. Light emission spectra of N2 molecules and \\text{N}2+ ions during the discharge are measured by optical diagnostics. The distributions of the positive \\text{N}2+ ions and the reduced electric field along the discharge channel are analyzed accordingly. The results show that the positive ions that can accumulate in space and distort the electric field play an important role on the formation of the Trichel pulse. The Trichel pulse is a mode transition between low-current Townsend discharge and high-current glow discharge. The rising time of the pulse corresponds to the breakdown and formation of glow discharge, and the decay time is related to destroy the process of positive ion clouds and the quenching of glow discharge. The time interval between the pulses is determined by the re-accumulation of positive ions near the cathode in the low-current Townsend discharge to form the positive ion clouds as well as a strongly-distorted electric field.

  12. Plasma density enhancement in atmospheric-pressure dielectric-barrier discharges by high-voltage nanosecond pulse in the pulse-on period: a PIC simulation

    Science.gov (United States)

    Sang, Chaofeng; Sun, Jizhong; Wang, Dezhen

    2010-02-01

    A particle-in-cell (PIC) plus Monte Carlo collision simulation is employed to investigate how a sustainable atmospheric pressure single dielectric-barrier discharge responds to a high-voltage nanosecond pulse (HVNP) further applied to the metal electrode. The results show that the HVNP can significantly increase the plasma density in the pulse-on period. The ion-induced secondary electrons can give rise to avalanche ionization in the positive sheath, which widens the discharge region and enhances the plasma density drastically. However, the plasma density stops increasing as the applied pulse lasts over certain time; therefore, lengthening the pulse duration alone cannot improve the discharge efficiency further. Physical reasons for these phenomena are then discussed.

  13. Discharge characteristics of an ablative pulsed plasma thruster with non-volatile liquid propellant

    Science.gov (United States)

    Ling, William Yeong Liang; Schönherr, Tony; Koizumi, Hiroyuki

    2017-07-01

    Pulsed plasma thrusters (PPTs) are a form of electric spacecraft propulsion. They have an extremely simple structure and are highly suitable for nano/micro-spacecraft with weights in the kilogram range. Such small spacecraft have recently experienced increased growth but still lack suitable efficient propulsion systems. PPTs operate in a pulsed mode (one discharge = one shot) and typically use solid polytetrafluoroethylene (PTFE) as a propellant. However, new non-volatile liquids in the perfluoropolyether (PFPE) family have recently been found to be promising alternatives. A recent study presented results on the physical characteristics of PFPE vs. PTFE, showing that PFPE is superior in terms of physical characteristics such as its resistance to carbon deposition. This letter will examine the electrical discharge characteristics of PFPE vs. PTFE. The results demonstrate that PFPE has excellent shot-to-shot repeatability and a lower discharge resistance when compared with PTFE. Taken together with its physical characteristics, PFPE appears to be a strong contender to PTFE as a PPT propellant.

  14. Measurements of Electric Field in a Nanosecond Pulse Discharge by 4-WAVE Mixing

    Science.gov (United States)

    Baratte, Edmond; Adamovich, Igor V.; Simeni Simeni, Marien; Frederickson, Kraig

    2017-06-01

    Picosecond four-wave mixing is used to measure temporally and Picosecond four-wave mixing is used to measure temporally and spatially resolved electric field in a nanosecond pulse dielectric discharge sustained in room air and in an atmospheric pressure hydrogen diffusion flame. Measurements of the electric field, and more precisely the reduced electric field (E/N) in the plasma is critical for determination rate coefficients of electron impact processes in the plasma, as well as for quantifying energy partition in the electric discharge among different molecular energy modes. The four-wave mixing measurements are performed using a collinear phase matching geometry, with nitrogen used as the probe species, at temporal resolution of about 2 ns . Absolute calibration is performed by measurement of a known electrostatic electric field. In the present experiments, the discharge is sustained between two stainless steel plate electrodes, each placed in a quartz sleeve, which greatly improves plasma uniformity. Our previous measurements of electric field in a nanosecond pulse dielectric barrier discharge by picosecond 4-wave mixing have been done in air at room temperature, in a discharge sustained between a razor edge high-voltage electrode and a plane grounded electrode (a quartz plate or a layer of distilled water). Electric field measurements in a flame, which is a high-temperature environment, are more challenging because the four-wave mixing signal is proportional to the to square root of the difference betwen the populations of N2 ground vibrational level (v=0) and first excited vibrational level (v=1). At high temperatures, the total number density is reduced, thus reducing absolute vibrational level populations of N2. Also, the signal is reduced further due to a wider distribution of N2 molecules over multiple rotational levels at higher temperatures, while the present four-wave mixing diagnostics is using spectrally narrow output of a ps laser and a high

  15. Characterization of stationary and pulsed inductively coupled RF discharges for plasma sterilization

    Science.gov (United States)

    Gans, T.; Osiac, M.; O'Connell, D.; Kadetov, V. A.; Czarnetzki, U.; Schwarz-Selinger, T.; Halfmann, H.; Awakowicz, P.

    2005-05-01

    Sterilization of bio-medical materials using radio frequency (RF) excited inductively coupled plasmas (ICPs) has been investigated. A double ICP has been developed and studied for homogenous treatment of three-dimensional objects. Sterilization is achieved through a combination of ultraviolet light, ion bombardment and radical treatment. For temperature sensitive materials, the process temperature is a crucial parameter. Pulsing of the plasma reduces the time average heat strain and also provides additional control of the various sterilization mechanisms. Certain aspects of pulsed plasmas are, however, not yet fully understood. Phase resolved optical emission spectroscopy and time resolved ion energy analysis illustrate that a pulsed ICP ignites capacitively before reaching a stable inductive mode. Time resolved investigations of the post-discharge, after switching off the RF power, show that the plasma boundary sheath in front of a substrate does not fully collapse for the case of hydrogen discharges. This is explained by electron heating through super-elastic collisions with vibrationally excited hydrogen molecules.

  16. An experimental study of high power microwave pulsed discharge in nitrogen

    Energy Technology Data Exchange (ETDEWEB)

    Mesko, M; Bonaventura, Z; Vasina, P; Kudrle, V; Talsky, A; Trunec, D; Frgala, Z; Janca, J [Department of Physical Electronics, Masaryk University, Kotlarska 2, CZ-61137 Brno (Czech Republic)

    2006-08-01

    We investigated a plasma excited by high power pulsed microwaves (MWs) (pulse duration 2.5 {mu}s, repetition rate 400 Hz, peak power 10{sup 5} W, frequency 9.4 GHz) in nitrogen at reduced pressure (pressure range 10-2000 Pa) with the aim of a better understanding of such types of discharge. The construction of the experimental device suppresses the plasma-wall interactions and therefore the volume processes are predominant. To obtain the temporal evolution of the electron density we used two MW interferometers at frequencies of 15 and 35 GHz with dielectric rod waveguides which gives them the capability of localized measurements. We estimated the effective collision frequency from the absorption of a measurement beam. Time resolved optical emission spectroscopy of the 1st negative system and the 2nd positive system was carried out, too. Due to a high power input the discharge dynamics was fast and the steady state was typically reached in 1 {mu}s. We found that the effective collision frequency has the same temporal behaviour as the 2nd positive system of N{sub 2}, including a characteristic maximum at the beginning of the pulse.

  17. Kinetic analysis of soil contained pyrene oxidation by a pulsed discharge plasma process

    Science.gov (United States)

    Huijuan, Wang; Guangshun, Zhou; He, Guo; Cong, Geng

    2017-01-01

    A pulsed discharge plasma (PDP) reactor with net anode and net cathode was established for investigating the pyrene degradation in soil under different pulse peak voltage, air flow rate, pyrene content in soil, initial pH value and initial water content of the soil. Pyrene oxidation within the 60 min discharge time was fitting according to the pseudo-first order equation and the corresponding reaction kinetics constants (k values) were calculated. The obtained results show that pyrene oxidation under all the different reaction conditions obeyed the pseudo-first order equation well. Higher pulsed peak voltage and appropriate air flow rate were in favor of the increase of reaction rate of pyrene oxidation. A higher k value could be achieved in the lower initial pyrene content (the value was 100 mg kg-1). The k value of pyrene oxidation in the case of pH = 4 was 11.2 times higher than the value obtained under the condition of pH = 9, while the initial water content of the soil also has a large effect on the oxidation rate of pyrene due to the effect of PDP. Supported by National Natural Science Foundation of China (No. 21207052).

  18. Ion mobility spectrometric analysis of vaporous chemical warfare agents by the instrument with corona discharge ionization ammonia dopant ambient temperature operation.

    Science.gov (United States)

    Satoh, Takafumi; Kishi, Shintaro; Nagashima, Hisayuki; Tachikawa, Masumi; Kanamori-Kataoka, Mieko; Nakagawa, Takao; Kitagawa, Nobuyoshi; Tokita, Kenichi; Yamamoto, Soichiro; Seto, Yasuo

    2015-03-20

    The ion mobility behavior of nineteen chemical warfare agents (7 nerve gases, 5 blister agents, 2 lachrymators, 2 blood agents, 3 choking agents) and related compounds including simulants (8 agents) and organic solvents (39) was comparably investigated by the ion mobility spectrometry instrument utilizing weak electric field linear drift tube with corona discharge ionization, ammonia doping, purified inner air drift flow circulation operated at ambient temperature and pressure. Three alkyl methylphosphonofluoridates, tabun, and four organophosphorus simulants gave the intense characteristic positive monomer-derived ion peaks and small dimer-derived ion peaks, and the later ion peaks were increased with the vapor concentrations. VX, RVX and tabun gave both characteristic positive monomer-derived ions and degradation product ions. Nitrogen mustards gave the intense characteristic positive ion peaks, and in addition distinctive negative ion peak appeared from HN3. Mustard gas, lewisite 1, o-chlorobenzylidenemalononitrile and 2-mercaptoethanol gave the characteristic negative ion peaks. Methylphosphonyl difluoride, 2-chloroacetophenone and 1,4-thioxane gave the characteristic ion peaks both in the positive and negative ion mode. 2-Chloroethylethylsulfide and allylisothiocyanate gave weak ion peaks. The marker ion peaks derived from two blood agents and three choking agents were very close to the reactant ion peak in negative ion mode and the respective reduced ion mobility was fluctuated. The reduced ion mobility of the CWA monomer-derived peaks were positively correlated with molecular masses among structurally similar agents such as G-type nerve gases and organophosphorus simulants; V-type nerve gases and nitrogen mustards. The slope values of the calibration plots of the peak heights of the characteristic marker ions versus the vapor concentrations are related to the detection sensitivity, and within chemical warfare agents examined the slope values for sarin, soman

  19. Accurate method for determining vibration temperatures, and gain limitation in pulse RF-discharge CO2 laser

    Institute of Scientific and Technical Information of China (English)

    Hussain Badran; TIAN Zhao-shuo(田兆硕); WANG Qi(王祁)

    2004-01-01

    An accurate method of determining gain coefficients of pulse RF-discharge CO2 laser is developed,which involves the use of both the regular 00°1 and 00°2 laser transitions as probes of CO2 laser. The results indicate that the majority of transitions in discharge have anomalous gain coefficients under RF-discharge condition. This fact has not been generally recognized and the neglect of overlapping transitions can lead to errors in determining rotational temperature.

  20. Guiding of Long-Distance Electric Discharges by Combined Femtosecond and Nanosecond Pulses Emitted by Hybrid KrF Laser System

    Science.gov (United States)

    2014-01-30

    laser pulse initiated HV discharge with a time delay of tens nanoseconds – evidently it is developing due to an avalanche -like growth of electron...AFRL-AFOSR-UK-TR-2014-0040 Guiding of long-distance electric discharges by combined femtosecond and nanosecond pulses emitted by...and guiding electric discharge , KrF laser, femtosecond pulse , nanosecond pulse , filamentation, plasma channel, lightning control, laser control of

  1. [Degradation of 4-chlorophenol in aqueous solution by high-voltage pulsed discharge-ozone technology].

    Science.gov (United States)

    Wen, Yuezhong; Jiang, Xuanzhen; Liu, Weiping

    2002-03-01

    The combination of high voltage pulse discharge and ozonation as an advanced oxidation technology was used to investigate the degradation of 4-chlorophenol (4-CP) in water. The factors that affect the rate of degradation were discussed. The 1.95 x 10(-3) mol/L solutions of 4-CP were almost completely (96%) degraded after the discharge treatment of 30 min. The degradation of 4-CP was investigated as a function of the ozone concentration, radical scavenger and electrode distance. The rate of 4-CP degradation increases with an increase in ozone concentration and a decrease in the electrode distance from 20 mm to 10 mm. The presence of radical scavenger decreased the rate of 4-CP degradation.

  2. Plasma polymerization of ethylene in an atmospheric pressure-pulsed discharge

    Science.gov (United States)

    Donohoe, K.; Wydeven, T.

    1979-01-01

    The polymerization of ethylene in an atmospheric pressure-pulsed discharge has been studied. Partial pressures of ethylene up to 4 kN/sq m were used with helium as a diluent. Deposition rates (on glass slides) were the same throughout the discharge volume over a wide range of operating conditions. These rates were in the 1-2 A/sec range. The films were clear, soft, and showed good adhesion to the glass substrates. Oligomers large enough to visibly scatter 637.8-nm light were observed in the gas phase under all conditions in which film deposition occurred. The experimental results suggest that Brownian diffusion of these oligomers was the rate-limiting step in the film deposition process.

  3. Impacts of air pressure on the evolution of nanosecond pulse discharge products

    Institute of Scientific and Technical Information of China (English)

    Yu Jin-Lu; He Li-Ming; Ding Wei; Wang Yu-Qian; Du Chun

    2013-01-01

    Based on the nonequilibrium plasma dynamics of air discharge,a dynamic model of zero-dimensional plasma is established by combining the component density equation,the Boltzmann equation,and the energy transfer equation.The evolution properties of nanosecond pulse discharge (NPD) plasma under different air pressures are calculated.The results show that the air pressure has significant impacts on the NPD products and the peak values of particle number density for particles such as O atoms,O3 molecules,N2(A3) molecules in excited states,and NO molecules.It increases at first and then decreases with the increase of air pressure.On the other hand,the peak values of particle number density for N2(B3)and N2(C3) molecules in excited states are only slightly affected by the air pressure.

  4. Observation of OH radicals produced by pulsed discharges on the surface of a liquid

    Science.gov (United States)

    Kanazawa, Seiji; Kawano, Hirokazu; Watanabe, Satoshi; Furuki, Takashi; Akamine, Shuichi; Ichiki, Ryuta; Ohkubo, Toshikazu; Kocik, Marek; Mizeraczyk, Jerzy

    2011-06-01

    The hydroxyl radical (OH) plays an important role in plasma chemistry at atmospheric pressure. OH radicals have a higher oxidation potential compared with other oxidative species such as free radical O, atomic oxygen, hydroperoxyl radical (HO2), hydrogen peroxide(H2O2) and ozone. In this study, surface discharges on liquids (water and its solutions) were investigated experimentally. A pulsed streamer discharge was generated on the liquid surface using a point-to-plane electrode geometry. The primary generation process of OH radicals is closely related to the streamer propagation, and the subsequent secondary process after the discharge has an influence on the chemical reaction. Taking into account the timescale of these processes, we investigated the behavior of OH radicals using two different diagnostic methods. Time evolution of the ground-state OH radicals above the liquid surface after the discharge was observed by a laser-induced fluorescence (LIF) technique. In order to observe the ground-state OH, an OH [A 2∑+(v' = 1) gas phase to the liquid surface and dissolved in the liquid. These dissolved OH radicals were measured by a chemical probe method. Terephthalic acid was used as an OH radical trap and fluorescence of the resulting 2-hydroxyterephthalic acid was measured. This paper directly presents visualization of OH radicals over the liquid surface by means of LIF, and indirectly describes OH radicals dissolved in water by means of a chemical method.

  5. Roughness modification of surfaces treated by a pulsed dielectric barrier discharge

    CERN Document Server

    Dumitrascu, N; Apetroaei, N; Popa, G

    2002-01-01

    Local modifications of surface roughness are very important in many applications, as this surface property is able to generate new mechano-physical characteristics of a large category of materials. Roughness is one of the most important parameters used to characterize and control the surface morphology, and techniques that allow modifying and controlling the surface roughness present increasing interest. In this respect we propose the dielectric barrier discharge (DBD) as a simple and low cost method that can be used to induce controlled roughness on various surfaces in the nanoscale range. DBD is produced in helium, at atmospheric pressure, by a pulsed high voltage, 28 kV peak to peak, 13.5 kHz frequency and 40 W power. This type of discharge is a source of energy capable of modifying the physico-chemical properties of the surfaces without affecting their bulk properties. The discharge is characterized by means of electrical probes and, in order to analyse the heat transfer rate from the discharge to the tre...

  6. Operating modes of a hydrogen ion source based on a hollow-cathode pulsed Penning discharge

    Energy Technology Data Exchange (ETDEWEB)

    Oks, E. M. [Institute of High Current Electronics, Siberian Branch of Russian Academy of Science, Tomsk (Russian Federation); Tomsk State University of Control System and Radioelectronics, Tomsk (Russian Federation); Shandrikov, M. V., E-mail: shandrikov@opee.hcei.tsc.ru; Vizir, A. V. [Institute of High Current Electronics, Siberian Branch of Russian Academy of Science, Tomsk (Russian Federation)

    2016-02-15

    An ion source based on a hollow-cathode Penning discharge was switched to a high-current pulsed mode (tens of amperes and tens of microseconds) to produce an intense hydrogen ion beam. With molecular hydrogen (H{sub 2}), the ion beam contained three species: H{sup +}, H{sub 2}{sup +}, and H{sub 3}{sup +}. For all experimental conditions, the fraction of H{sub 2}{sup +} ions in the beam was about 10 ÷ 15% of the total ion beam current and varied little with ion source parameters. At the same time, the ratio of H{sup +} and H{sub 3}{sup +} depended strongly on the discharge current, particularly on its distribution in the gap between the hollow and planar cathodes. Increasing the discharge current increased the H{sup +} fraction in ion beam. The maximum fraction of H{sup +} reached 80% of the total ion beam current. Forced redistribution of the discharge current in the cathode gap for increasing the hollow cathode current could greatly increase the H{sub 3}{sup +} fraction in the beam. At optimum parameters, the fraction of H{sub 3}{sup +} ions reached 60% of the total ion beam current.

  7. Microsecond resolved electron density measurements with a hairpin resonator probe in a pulsed ICP discharge

    CERN Document Server

    Peterson, David; Larson, Lynda; Shannon, Steven

    2016-01-01

    Time resolved electron density measurements in pulsed RF discharges are shown using a hairpin resonance probe using low cost electronics, on par with normal Langmuir probe boxcar mode operation. Time resolution of less than one microsecond has been demonstrated. A signal generator produces the applied microwave frequency; the reflected waveform is passed through a directional coupler and filtered to remove the RF component. The signal is heterodyned with a frequency mixer and read by an oscilloscope. At certain points during the pulse, the plasma density is such that the applied frequency is the same as the resonance frequency of the probe/plasma system, creating a dip in the reflected signal. The applied microwave frequency is shifted in small increments in a frequency boxcar routine to determine the density as a function of time. The system uses a grounded probe to produce low cost, high fidelity, and highly reproducible electron density measurements that can work in harsh chemical environments. Measurement...

  8. Natural discharge after pulse and cooperative electrodes to enhance droplet velocity in digital microfluidics

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Tianlan; Dong, Cheng; Gao, Jie; Jia, Yanwei; Mak, Pui-In, E-mail: pimak@umac.mo; Vai, Mang-I; Martins, Rui P. [State Key Laboratory of Analog and Mixed-Signal VLSI and FST-ECE, University of Macau, Macao (China)

    2014-04-15

    Digital Microfluidics (DMF) is a promising technology for biological/chemical micro-reactions due to its distinct droplet manageability via electronic automation, but the limited velocity of droplet transportation has hindered DMF from utilization in high throughput applications. In this paper, by adaptively fitting the actuation voltages to the dynamic motions of droplet movement under real-time feedback monitoring, two control-engaged electrode-driving techniques: Natural Discharge after Pulse (NDAP) and Cooperative Electrodes (CE) are proposed. They together lead to, for the first time, enhanced droplet velocity with lower root mean square voltage value.

  9. Measurement of metal vapor cooling speed during nanoparticle formation by pulsed wire discharge

    Institute of Scientific and Technical Information of China (English)

    Yuu SHIKODA; Yoshinori TOKOI; Koji SUWA; Satoru ISHIHARA; Tsuneo SUZUKI; Tadachika NAKAYAMA; Hisayuki SUEMATSU; Koichi NIIHARA

    2009-01-01

    Pulsed wire discharge(PWD) is one of nano-sized powder production methods. The object of this work is to study influence of the plasma/vapor/particle density using computer simulation and to establish temperature measurement method using a high-speed infrared thermometer in the PWD process. The temperature correction coefficient was obtained from geometric computer simulation results. Obtained correction coefficient was applied to the temperature measuring results. It was found from this result that obtained correction coefficient was appropriate. A temperature measurement method was established by using the high-speed infrared thermometer in PWD.

  10. Temperature field at time of pulse current discharge in metal structure with elliptical embedding crack

    Institute of Scientific and Technical Information of China (English)

    FU Yu-ming; TIAN Zhen-guo; ZHENG Li-juan; LI Wei

    2008-01-01

    Theoretical analysis is made on the temperature field at the time of pulse current discharge in a metal structure with an elliptical embedding crack. In finding the temperature field, analogy between the current flow through an elliptical embedding crack and the fluid flow through a barrier is made based on the similarity principle. Boundary conditions derived from this theory are introduced so that the distribution of current density and the temperature field expressions can be obtained. The study provides a theoretic basis to the applications of stopping spatial crack with electromagnetic heating.

  11. Reduction of TiO2 with hydrogen cold plasma in DC pulsed glow discharge

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yu-wen; DING Wei-zhong; LU Xiong-gang; GUO Shu-qiang; XU Kuang-di

    2005-01-01

    The reduction of TiO2 to Ti2O3 with hydrogen cold plasma generated by a DC pulsed glow discharge was realized under 2 500 Pa at 1 233 K. Only a little of Ti10O19 and Ti9O17 was detected for using molecular hydrogen.Enhancement effects of hydrogen cold plasma on the reduction were discussed in terms of thermodynamic coupling,kinetics and plasma sheath. The exited hydrogen species are considered more effective reducing agents. It is instructive to reduce refractory oxides with plasma hydrogen at the reduced temperature.

  12. Synthesis of Crystalline Carbon Nitride Thin Films by Pulsed Arc Discharge at Atmospheric Pressure

    Institute of Scientific and Technical Information of China (English)

    SHI Changyong; MA Zhibin

    2007-01-01

    The preparation of crystalline C3N4 films was investigated using pulsed arc discharge from mixed methanol and ammonia water at atmospheric pressure.The X-ray diffraction(XRD)patterns of the films prepared at a substrate temperature of 450℃ suggested that the film was composed of α-C3N4 and β-C3N4 crystallites.Raman spectra exhibited distinct peaks which are in good agreement with those predicted theoretically for C3N4 crystallites.

  13. Conditions for uniform impact of the plasma of a runaway-electron-induced pulsed diffuse discharge on an anode

    Science.gov (United States)

    Erofeev, M. V.; Baksht, E. Kh.; Burachenko, A. G.; Tarasenko, V. F.

    2015-09-01

    The subject matters in this work are (i) the spatial structure of a volume (diffuse) discharge initiated in atmospheric-pressure air in a heavily nonuniform electric field by nanosecond voltage pulses and (ii) the influence of its plasma on the surface of a plane aluminum anode. It is shown that a diffuse discharge initiated by nanosecond voltage pulses makes it possible to uniformly process the anode's surface in atmospheric-pressure air in contrast to a spark discharge, which results in microcracking, locally changes the surface properties, and thereby degrades the surface.

  14. Investigation of positive and negative modes of nanosecond pulsed discharge in water and electrostriction model of initiation

    CERN Document Server

    Seepersad, Yohan; Dobrynin, Danil

    2013-01-01

    This work investigates the development of nanosecond pulsed discharges in water ignited with the application of both positive and negative polarity pulses to submerged pin to plane electrodes. Optical diagnostics are used to study two main aspects of these discharges: the initiation phase, and the development phase. Nanosecond pulses up to 24 kV with 4 ns rise time, 10 ns duration and 5 ns fall time are used to ignite discharges in a 1.5 mm gap between a copper plate and a tungsten needle with radius of curvature of 25 um. Fast ICCD imaging is used to trace the discharge development over varying applied pulse amplitudes for both positively and negatively applied pulses to the pin electrode. The discharge is found to progress similar to that of discharges in long gaps in gases, both in structure and development. The more important initiation phase is investigated via Schlieren transmission imaging. The region near the tip of the electrode is investigated for slightly under-breakdown conditions, and changes in ...

  15. 同轴电极的负电晕特里切尔脉冲特性分析%Characteristics of Negative Corona Trichel Pulses in a Coaxial Electrode System

    Institute of Scientific and Technical Information of China (English)

    何旺龄; 何俊佳; 张锦; 万保权

    2016-01-01

    利用流体动力学模型,对大气压条件下空气间隙的同轴电极结构进行了负极性电晕放电特性研究,获得了一组规则的特里切尔脉冲。除第一个脉冲外,其他脉冲的幅值均在1.5~2.5 mA。然后,对第一个脉冲(称为第一脉冲)不同发展阶段的空间电场分布和粒子密度分布进行了描述,并讨论了第一脉冲与第二脉冲之间的死区时间内不同时刻负离子密度的变化过程及其对阴极表面电场的影响作用,最后,对第二脉冲发展前后空间电场分布、电子密度分布和负离子密度分布及其变化规律进行了进一步的描述。仿真表明,随着负离子在电场力的作用下逐渐向外迁移,导线表面电场强度开始恢复,但其恢复速度在负离子远离导线的过程中逐渐变缓。同时,当导线表面电场强度恢复至低于初始拉普拉斯场强的某一特定值时,新的脉冲就开始发生,第二脉冲发生时空间电场、电子密度及负离子密度的最大值均小于第一脉冲。%In this paper,the characteristics of negative corona discharge in air at atmospheric pressure are studied by using the hydrodynamic drift-diffusion model with a coaxial electrode system,and a set of regular Trichel pulses is obtained. It is found that the pulse amplitude is between 1. 5 mA and 2. 5 mA except the first one. Then the distributions of the electric field,the ion densities at different stages during the first pulse are plotted. The distribution of the negative ion density and its influence on the conductor surface electric field are discussed during the dead time between the first pulse and the second pulse. After that,the distributions of the electric field,the electron and negative ion densities around the second pulse are plotted. The simulation results show that the electric field at the conductor surface increases when the negative ions remove from cathode under the influence of electric

  16. Magnetic discharge accelerating diode for the gas-filled pulsed neutron generators based on inertial confinement of ions

    Science.gov (United States)

    Kozlovskij, K. I.; Shikanov, A. E.; Vovchenko, E. D.; Shatokhin, V. L.; Isaev, A. A.; Martynenko, A. S.

    2016-09-01

    The paper deals with magnetic discharge diode module with inertial electrostatic ions confinement for the gas-filled pulsed neutron generators. The basis of the design is geometry with the central hollow cathode surrounded by the outer cylindrical anode and electrodes made of permanent magnets. The induction magnitude about 0.1-0.4 T in the central region of the discharge volume ensures the confinement of electrons in the space of hollow (virtual) cathode and leads to space charge compensation of accelerated ions in the centre. The research results of different excitation modes in pulsed high-voltage discharge are presented. The stable form of the volume discharge preserveing the shape and amplitude of the pulse current in the pressure range of 10-3-10-1 Torr and at the accelerating voltage up to 200 kV was observed.

  17. Pulsed positive discharges in air at moderate pressures near a dielectric rod

    Science.gov (United States)

    Dubinova, A.; Trienekens, D.; Ebert, U.; Nijdam, S.; Christen, T.

    2016-10-01

    We study pulsed positive discharges in air in a cylindrically symmetric setup with an electrode needle close (about 1 mm) above the top of a dielectric cylindrical rod of 4 mm in diameter mounted at its bottom on a grounded plate electrode. We present ICCD (intensified charge-coupled device) pictures and evaluations of experiments as well as simulations with a fluid discharge model; the simulations use cylindrical symmetry. In the experiments, there is an initial inception cloud phase, where the cylindrical symmetry is maintained, and later a streamer phase, where it is broken spontaneously. At 75-150 mbar, discharges with cylindrical symmetry are not attracted to the dielectric rod, but move away from it. The dielectric rod plays the sole role of an obstacle that shades (in the context of photoionization) a cone-shaped part of the inception cloud; the cone size is determined by the geometry of the setup. The material properties of the dielectric rod, such as its dielectric permittivity and the efficiency of the photon induced secondary electron emission do not have a noticeable effect. This is due to the abundance of photoionization in air, which supplies a positive discharge with free electrons and allows it to propagate along the electric field lines. Using some simple field calculations, we show that field enhancement due to dielectric polarization does not play a significant role in our geometry as long as the discharge maintains its cylindrical symmetry. The field component towards the rod is insufficiently enhanced to cause the discharge to move towards the rod. Any additional electrons produced by the dielectric surface do not influence this discharge morphology. This interpretation is supported by both experiments and simulations. At higher pressures (400-600 mbar) or for larger gaps between the needle and the dielectric rod, the inception cloud reaches its maximal radius within the gap between needle and rod and destabilizes there. In those cases

  18. 脉冲放电等离子体甲烷氯化制氯代甲烷%Chlorination of methane by pulsed electrical discharge plasma

    Institute of Scientific and Technical Information of China (English)

    祝成凤; 黄立维; 张永霞; 何联候

    2012-01-01

    采用脉冲电晕放电等离子体活化手段在线-筒式反应器中,进行甲烷氯化合成氯代甲烷反应.考察了原料气V(Cl2):V(CH4)值、电晕放电脉冲电压和电晕放电重复频率参数对甲烷转化率及氯代甲烷选择性的影响.反应物及各产物通过气相色谱法进行在线分析.实验结果表明:常温常压下,在脉冲电晕等离子体作用下,甲烷和氯气反应可以生成氯代甲烷.甲烷的转化率随加入能量强度的增加而提高.提高氯气/甲烷摩尔比,多氯甲烷的产率也提高.当反应气总流速为100 mL/min,V(Cl2)∶V(CH4)=1.2∶1,脉冲放电电压为17.5 kV,放电频率为80 Hz时,甲烷的转化率为10.5%,一氯甲烷、二氯甲烷、三氯甲烷和四氯甲烷的选择性分别为67.6%,17.7%,13.3%和1.4%.%The chlorination of methane by pulsed electrical discharge in a wire-cylinder reactor was experimentally investigated. The effects of parameters such as the ratio of V(C12) to V(CH4), the pulse discharge voltage, as well as the pulse discharge frequency, on methane conversion and chlorinated methanes (CMS) selectivity were focused on. The products from methane conversion were analyzed by on-line gas-chromatography (GC). Experimental results showed that methane could react with chlorine to produce CMS by pulsed corona discharge plasma at room temperature and atmospheric pressure. It was found that the yield of products increased with the increase of power input into the reactor. The chlorination proceeded more completely with higher C12/CH4 mole ratio. The conversion of methane was 10. 5%, and the selectivity of chlorinated methanes were 67.6%, 17.7%, 13.3% and 1.4% respectively with the conditions of V(C12) :V(CH4) = 1. 2 : 1, total flow rate of 100 mL/min, pulse discharge voltage of 17. 5 kV and the discharge frequency of 80 Hz.

  19. Determination of space-time resolved electron temperature in nanosecond pulsed longitudinal discharge in various noble gases and discharge tube constructions

    Science.gov (United States)

    Temelkov, K. A.; Slaveeva, S. I.; Chernogorova, T. P.

    2016-03-01

    Using our results obtained by the analytical solution of the steady-state heat conduction equation for electrons and deriving a new thermal conductivity, 2D (r, t) numerical solution of nonstationary heat conduction, an equation for electrons is found for nanosecond pulsed longitudinal discharge in helium for two different pressures and in neon.

  20. Effect of Duty Cycle on the Characteristics of Pulse-Modulhted Radio-Frequency Atmospheric Pressure Dielectric Barrier Discharge

    Institute of Scientific and Technical Information of China (English)

    LI Xuechun; WANG Huan; DING Zhenfeng; WANG Younian

    2012-01-01

    Using a one-dimensional fluid model, the pulse-modulated radio-frequency dielectric barrier discharge in atmospheric helium is described. The influences of the pulse duty cycle on the discharge characteristics are studied. The numerical results show that the dependence of discharge characteristics on the duty cycle is sensitive in the region of around 40% duty cycle under the given simulation parameters. In the case of a larger duty cycle, the plasma density is higher, the discharge becomes more intense, but the power consumption is higher. When the duty cycle is lower, one can get a weaker discharge, lower plasma density and higher electron temperature in the bulk plasma. In practical applications, in order to get a higher plasma density and a lower power consumption, it is more important to choose a suitable duty cycle to modulate the RF power supply.

  1. Self-consistent evolution of plasma discharge and electromagnetic fields in a microwave pulse compressor

    Energy Technology Data Exchange (ETDEWEB)

    Shlapakovski, A. S.; Beilin, L.; Krasik, Ya. E. [Physics Department, Technion 32000 Haifa (Israel); Hadas, Y. [Department of Applied Physics, Rafael, POBox 2250, Haifa 31021 (Israel); Schamiloglu, E. [Department of Electrical and Computer Engineering, University of New Mexico, Albuquerque, New Mexico 87131 (United States)

    2015-07-15

    Nanosecond-scale evolution of plasma and RF electromagnetic fields during the release of energy from a microwave pulse compressor with a plasma interference switch was investigated numerically using the code MAGIC. The plasma was simulated in the scope of the gas conductivity model in MAGIC. The compressor embodied an S-band cavity and H-plane waveguide tee with a shorted side arm filled with pressurized gas. In a simplified approach, the gas discharge was initiated by setting an external ionization rate in a layer crossing the side arm waveguide in the location of the electric field antinode. It was found that with increasing ionization rate, the microwave energy absorbed by the plasma in the first few nanoseconds increases, but the absorption for the whole duration of energy release, on the contrary, decreases. In a hybrid approach modeling laser ignition of the discharge, seed electrons were set around the electric field antinode. In this case, the plasma extends along the field forming a filament and the plasma density increases up to the level at which the electric field within the plasma decreases due to the skin effect. Then, the avalanche rate decreases but the density still rises until the microwave energy release begins and the electric field becomes insufficient to support the avalanche process. The extraction of the microwave pulse limits its own power by terminating the rise of the plasma density and filament length. For efficient extraction, a sufficiently long filament of dense plasma must have sufficient time to be formed.

  2. Self-consistent evolution of plasma discharge and electromagnetic fields in a microwave pulse compressor

    Science.gov (United States)

    Shlapakovski, A. S.; Beilin, L.; Hadas, Y.; Schamiloglu, E.; Krasik, Ya. E.

    2015-07-01

    Nanosecond-scale evolution of plasma and RF electromagnetic fields during the release of energy from a microwave pulse compressor with a plasma interference switch was investigated numerically using the code MAGIC. The plasma was simulated in the scope of the gas conductivity model in MAGIC. The compressor embodied an S-band cavity and H-plane waveguide tee with a shorted side arm filled with pressurized gas. In a simplified approach, the gas discharge was initiated by setting an external ionization rate in a layer crossing the side arm waveguide in the location of the electric field antinode. It was found that with increasing ionization rate, the microwave energy absorbed by the plasma in the first few nanoseconds increases, but the absorption for the whole duration of energy release, on the contrary, decreases. In a hybrid approach modeling laser ignition of the discharge, seed electrons were set around the electric field antinode. In this case, the plasma extends along the field forming a filament and the plasma density increases up to the level at which the electric field within the plasma decreases due to the skin effect. Then, the avalanche rate decreases but the density still rises until the microwave energy release begins and the electric field becomes insufficient to support the avalanche process. The extraction of the microwave pulse limits its own power by terminating the rise of the plasma density and filament length. For efficient extraction, a sufficiently long filament of dense plasma must have sufficient time to be formed.

  3. Effects of solution volume on hydrogen production by pulsed spark discharge in ethanol solution

    Science.gov (United States)

    Xin, Y. B.; Sun, B.; Zhu, X. M.; Yan, Z. Y.; Liu, H.; Liu, Y. J.

    2016-07-01

    Hydrogen production from ethanol solution (ethanol/water) by pulsed spark discharge was optimized by varying the volume of ethanol solution (liquid volume). Hydrogen yield was initially increased and then decreased with the increase in solution volume, which achieved 1.5 l/min with a solution volume of 500 ml. The characteristics of pulsed spark discharge were studied in this work; the results showed that the intensity of peak current, the rate of current rise, and energy efficiency of hydrogen production can be changed by varying the volume of ethanol solution. Meanwhile, the mechanism analysis of hydrogen production was accomplished by monitoring the process of hydrogen production and the state of free radicals. The analysis showed that decreasing the retention time of gas production and properly increasing the volume of ethanol solution can enhance the hydrogen yield. Through this research, a high-yield and large-scale method of hydrogen production can be achieved, which is more suitable for industrial application.

  4. Ion kinetics and self pulsing in DC microplasma discharges at atmospheric and higher pressure

    Science.gov (United States)

    Mahamud, Rajib; Farouk, Tanvir I.

    2016-04-01

    Atmospheric pressure microplasma devices have been the subject of considerable interest and research during the last decade. Most of the operation regime of the plasma discharges studied fall in the ‘abnormal’, ‘normal’ and ‘corona’ modes—increasing and a ‘flat’ voltage current characteristics. However, the negative differential resistance regime at atmospheric and high pressures has been less studied and possesses unique characteristics that can be employed for novel applications. In this work, the role of ion kinetics especially associated with trace impurities; on the self pulsing behavior has been investigated. Detailed numerical simulations have been conducted with a validated model for a helium-nitrogen feed gas mixture. Different oscillatory modes were observed where the discharge was found to undergo complete or partial relaxation. Trace amount of nitrogen was found to significantly alter the pulsing characteristics. External parameters influencing these self oscillations are also studied and aspects of the ion kinetics on the oscillatory behavior are discussed.

  5. Characteristics of gas-liquid pulsed discharge plasma reactor and dye decoloration efficiency

    Institute of Scientific and Technical Information of China (English)

    Bing Sun; Nyein Nyein Aye; Zhiying Gao; Dan Lv; Xiaomei Zhu; Masayuki Sato

    2012-01-01

    The pulsed high-voltage discharge is a new advanced oxidation technology for water treatment.Methyl Orange (MO) dye wastewater was chosen as the target object.Some investigations were conducted on MO decoloration including the discharge characteristics of the multi-needle reactor,parameter optimization,and the degradation mechanism.The following results were obtained.The color group of the azo dye MO was effectively decomposed by water surface plasma.The decoloration rate was promoted with the increase of treatment time,peak voltage,and pulse frequency.When the initial conductivity was 1700 tS/cm,the decoloration rate was the highest.The optimum distahce between the needle electrodes and the water surface was 1 mm,the distance between the grounding electrode and the water surface was 28 mm,and the number of needle electrodes and spacing between needles were 24 and 7.5 mm,respectively.The decoloration rate of MO was affected by the gas in the reactor and varied in the order oxygen > air> argon > nitrogen,and the energy yield obtained in this investigation was 0.45 g/kWh.

  6. Fundamental Research on Rare Gas Fluorescent Pulsed Discharge Lamps for Mercuryless Lamps

    Science.gov (United States)

    Jinno, Masafumi; Kurokawa, Hisayoshi; Aono, Masaharu

    1998-10-01

    The characteristics of xenon-neon fluorescent discharge lamps with inner electrodes, and of xenon fluorescent discharge lamps with both inner electrodes and external electrodes were investigated at the pulsed operation. In the case of the inner electrodes type, when the partial pressure of neon is high, the ignition voltage is low because of the Penning effect. Then, the high mixing ratio of neon is desirable to lower the ignition voltage. However, the luminance of the phosphor increases as the mixing ratio of xenon increases. Therefore, in order to get high luminance, xenon should be fill at high mixing ratio. If only xenon is filled in a lamp with inner electrodes, the cathode is bomberd and damaged by the large mass of xenon ions. Consequently, the most suitable mixing ratio of xenon and neon or some other buffer gases should be found for inner electrode type. When the lamp filled only with xenon is operated by external electrodes, the afterglow emission of the phosphor increases as the pressure of xenon increases. These increases following the increase in xenon pressure seem to be caused by the UV light of xenon excimers. However, the starting voltage becomes higher at high xenon pressure. So, the external electrode type requires the optimization of some conditions such as electrodes, pulse frequency, etc.

  7. Effects of solution volume on hydrogen production by pulsed spark discharge in ethanol solution

    Energy Technology Data Exchange (ETDEWEB)

    Xin, Y. B.; Sun, B., E-mail: sunb88@dlmu.edu.cn; Zhu, X. M.; Yan, Z. Y.; Liu, H.; Liu, Y. J. [College of Environmental Science and Engineering, Dalian Maritime University, Dalian 116026 (China)

    2016-07-15

    Hydrogen production from ethanol solution (ethanol/water) by pulsed spark discharge was optimized by varying the volume of ethanol solution (liquid volume). Hydrogen yield was initially increased and then decreased with the increase in solution volume, which achieved 1.5 l/min with a solution volume of 500 ml. The characteristics of pulsed spark discharge were studied in this work; the results showed that the intensity of peak current, the rate of current rise, and energy efficiency of hydrogen production can be changed by varying the volume of ethanol solution. Meanwhile, the mechanism analysis of hydrogen production was accomplished by monitoring the process of hydrogen production and the state of free radicals. The analysis showed that decreasing the retention time of gas production and properly increasing the volume of ethanol solution can enhance the hydrogen yield. Through this research, a high-yield and large-scale method of hydrogen production can be achieved, which is more suitable for industrial application.

  8. AIR ATMOSPHERIC-PRESSURE DISCHARGERS FOR OPERATION IN HIGH-FREQUENCY SWITCHING MODE.

    Directory of Open Access Journals (Sweden)

    L.S. Yevdoshenko

    2013-10-01

    Full Text Available Operation of two designs of compact multigap dischargers has been investigated in a high-frequency switching mode. It is experimentally revealed that the rational length of single discharge gaps in the designs is 0.3 mm, and the maximum switching frequency is 27000 discharges per second under long-term stable operation of the dischargers. It is shown that in pulsed corona discharge reactors, the pulse front sharpening results in increasing the operating electric field strength by 1.3 – 1.8 times.

  9. Laser-Ionization TOF Mass Spectrometer Characterization of Benzene Destruction in Atmospheric Pressure Pulsed Discharge

    Institute of Scientific and Technical Information of China (English)

    LIU Jiahong; XIAO Qingmei; WANG Liping; YAO Zhi; DING Hongbin

    2009-01-01

    Benzene is.a major industrial air pollutant and can cause serious human health disorders. In this paper an investigation on benzene destruction, in an atmospheric-pressure fast-flow pulsed DC-discharge by means of laser ionization combined with time-of-flight (TOF) mass spectrometry, is reported. Most by-products including transient reactive species from the benzene discharge were characterized by molecular beam sampling combined with TOF mass spectrometry.It is showed that, with a gas mixture of 0.5% C6H6 in Ar, benzene can be effectively destroyed by discharge plasma. The intermediate species consisted of small fragments of CNHm (n=3~5,m =1~11), cycle-chain species of CNHm (n=6~9, m = 7~10) and polycyclic species CNHm (n ≥9,m = 8~12). The alternation of mass peaks (intensity) with even/odd electrons was observed in the measured mass spectra. The results indicated that the alternation is mainly due to the different ionization potentials of the open shell and close shell species. Based on the examination of the features of the species' composition, the primary reaction pathways are proposed and discussed.

  10. Langmuir probe study of a titanium pulsed filtered cathodic arc discharge

    Energy Technology Data Exchange (ETDEWEB)

    Andruczyk, D [School of Physics, University of Sydney, NSW 2006 (Australia); Tarrant, R N [School of Physics, University of Sydney, NSW 2006 (Australia); James, B W [School of Physics, University of Sydney, NSW 2006 (Australia); Bilek, M M M [School of Physics, University of Sydney, NSW 2006 (Australia); Warr, G B [School of Physics, University of Sydney, NSW 2006 (Australia)

    2006-08-01

    A Langmuir probe has been used to make measurements of plasma parameters as a function of time at the substrate position in a magnetically-filtered pulsed cathodic arc discharge. Electron density, n{sub e}, and effective electron temperature, T{sub eff}, were calculated as a function of time from the I-V curves. The Druyvesteyn method was used to determine the electron energy distribution. Ion density was calculated using the assumption of plasma quasi-neutrality and an average ion charge state. Results show that over the plateau region (350-600 {mu}s) of the pulse, the electron energy distribution is Maxwellian with T{sub eff} = T{sub e} = (10 {+-} 1) eV. During the rise and fall times of the pulse, the electron energy distribution is non-Maxwellian with an effective temperature of up to 15 to 20 eV during the rise time and {approx}7 eV during the fall time. The electron density during the plateau is n{sub e} = (3.0-6.0 {+-} 0.5) x 10{sup 17} m{sup -3}.

  11. Spectroscopic analysis of high electric field enhanced ionization in laser filaments in air for corona guiding

    Institute of Scientific and Technical Information of China (English)

    Yingxia Wei; Yaoxiang Liu; Tie-Jun Wang; Na Chen; Jingjing Ju; Yonghong Liu; Haiyi Sun; Cheng Wang; Jiansheng Liu; Haihe Lu; See Leang Chin; Ruxin Li

    2016-01-01

    We report on a systematic experimental study on the fluorescence spectra produced from a femtosecond laser filament in air under a high electric field. The electric field alone was strong enough to create corona discharge(CD). Fluorescence spectra from neutral and ionic air molecules were measured and compared with pure high-voltage CD and pure laser filamentation(FIL). Among them, high electric field assisted laser FIL produced nitrogen fluorescence more efficiently than either pure CD or pure FIL processes. The nonlinear enhancement of fluorescence from the interaction of the laser filament and corona discharging electric field resulted in a more efficient ionization along the laser filament zone, which was confirmed by the spectroscopic measurement of both ionization-induced fluorescence and plasma-scattered 800 nm laser pulses. This is believed to be the key precursor process for filament-guided discharge.

  12. Application of a pulse-discharge helium detector to the determination of neon in air and water.

    Science.gov (United States)

    Lasa, J; Mochalski, P; Lokas, E; Kedzior, L

    2002-08-30

    A pulse-discharge helium detector (Valco, PD-D2-I) is used to measure neon concentrations in air and water. The detection level is 0.5 x 10(-8) g/cm3 (0.2 ppm). Discharge gas doped with neon results in a linear response to the neon mass up to 10(-6) g. For measuring the neon concentration in water, a simple enrichment system is used.

  13. Sterilization of Fungus in Water by Pulsed Power Gas Discharge Reactor Spraying Water Droplets for Water Treatment

    Science.gov (United States)

    Saito, Tsukasa; Handa, Taiki; Minamitani, Yasushi

    We study sterilization of bacteria in water using pulsed streamer discharge of gas phase. This method enhances efficiency of water treatment by spraying pretreatment water in a streamer discharge area. In this paper, yeast was sterilized because we assumed a case that fungus like mold existed in wastewater. As a result, colony forming units decreased rapidly for 2 minutes of the processing time, and all yeast sterilized by 45 minutes of the processing time.

  14. SMALL VOLUME LONG PULSE X RAY PREIONISED XeCl LASER WITH DOUBLE DISCHARGE AND FAST FERRITE MAGNETIC SWITCH

    OpenAIRE

    J. Hueber; Kobhio, M.; Fontaine, B.; Delaporte, Ph.; Sentis, M.; Forestier, B.

    1991-01-01

    Experimental results obtained with a high efficiency small volume long pulse X-Ray preionised XeCl laser with double discharge and very fast ferrite magnetic switch are presented and compared with the results given by a new XeCl laser numerical self consistant model. The model takes into account most recent kinetic data and time variation of discharge impedence and switch inductance. There is a good agreement between experiment and model on electrical and laser parameters for typical conditions.

  15. Study on the mode-transition of nanosecond-pulsed dielectric barrier discharge between uniform and filamentary by controlling pressures and pulse repetition frequencies

    Science.gov (United States)

    Yu, S.; Pei, X.; Hasnain, Q.; Nie, L.; Lu, X.

    2016-02-01

    In this paper, we investigate the temporally resolved evolution of the nanosecond pulsed dielectric barrier discharge (DBD) in a moderate 6 mm discharge gap under various pressures and pulse repetition frequencies (PRFs) by intensified charge-coupled device (ICCD) images, using dry air and its components oxygen and nitrogen. It is found that the pressures are very different when the mode transits between uniform and filamentary in air, oxygen, and nitrogen. The PRFs can also obviously affect the mode-transition. The transition mechanism in the pulsed DBD is not Townsend-to-Streamer, which is dominant in the traditional alternating-voltage DBD. The pulsed DBD in a uniform mode develops in the form of plane ionization wave due to overlap of primary avalanches, while the increase in pressure disturbs the overlap and discharge develops in streamer, corresponding to the filamentary mode. Increasing the initial electron density by pre-ionization may contribute to discharge uniformity at higher pressures. We also found that the dependence of homogeneity upon PRF is a non-monotonic one.

  16. Influence of deposited energy on shock wave induced by underwater pulsed current discharge

    Science.gov (United States)

    Li, Xian-Dong; Liu, Yi; Liu, Si-Wei; Li, Zhi-Yuan; Zhou, Gu-Yue; Li, Hua; Lin, Fu-Chang; Pan, Yuan

    2016-10-01

    In this paper, an integrated experimental system is established to study the influence of deposited energy on the intensity of the shock wave induced by underwater pulse discharge. Considering the time varying behavior of the arc, the calculation methods of the deposited energy into the plasma channel and the average arc resistance are proposed and presented. The effect of the breakdown process on the deposited energy and the shock wave is analyzed. It can be concluded that the shock wave intensity can be improved by depositing more energy in the first half oscillation period and increasing the arc resistance. It is also found that the energy deposition and the shock wave intensity are significantly influenced by the breakdown time delay and the shape of the initial plasma channel.

  17. Determination of Xenon in Air by a Pulse-discharge Helium Ionization Detector

    Institute of Scientific and Technical Information of China (English)

    CHEN Zhan-ying; CHANG Yin-zhong; LIU Shu-jiang; ZHANG Hai-tao; WANG Shi-lian; LI Qi

    2012-01-01

    A pulse-discharge helium ionization detector(Valco,PD-D3-I) was used to measure xenon concentration in air.The dependences of the detector relative response on various gas chromatograph parameters were investigated.Based on the well prepared gas connections for the detector system and optimized gas ehromatography(GC) working conditions,the atmospheric xenon concentration could be measured by the cheap GC method with a detection level of 0.7×10-9(parts by volume).Moreover,the xenon concentration in the ground level air around our laboratory was measured with the result of 0.085 × 10-6(parts by volume) and RSD of 0.91%.

  18. Pretreatment of food waste with high voltage pulse discharge towards methane production enhancement.

    Science.gov (United States)

    Zou, Lianpei; Ma, Chaonan; Liu, Jianyong; Li, Mingfei; Ye, Min; Qian, Guangren

    2016-12-01

    Anaerobic batch tests were performed to investigate the methane production enhancement and solid transformation rates from food waste (FW) by high voltage pulse discharge (HVPD) pretreatment. The total cumulative methane production with HVPD pretreatment was 134% higher than that of the control. The final volatile solids transformation rates of FW with and without HVPD pretreatment were 54.3% and 32.3%, respectively. Comparison study on HVPD pretreatment with acid, alkali and ultrasonic pretreatments showed that the methane production and COD removal rates of FW pretreated with HVPD were more than 100% higher than the control, but only about 50% higher can be obtained with other pretreatments. HVPD pretreatment could be a promising pretreatment method in the application of energy recovery from FW.

  19. Degradation of Dye Wastewater by Pulsed High-Voltage Discharge Combined with Spent Tea Leaves

    Science.gov (United States)

    Liu, Yan; Yang, Li; Yang, Gang; Zhang, Yanzong; Zhang, Xiaohong; Deng, Shihuai

    2014-12-01

    Degradation of methylene blue (MB) was performed using the pulsed discharge process (PDP) combined with spent tea leaves (STLs). The effects of STL dosage, concentration of initial solution, and pH were analyzed in the combined treatment. Results showed that the combined treatment was effective for dye wastewater degradation; when the dosage of STLs was 3.2 g/L, the degradation efficiency reached 90% after 15 min treatment, and STLs showed a good repeatability. The degradation rate decreased with increasing initial MB concentration but not related to the solution pH in the combined treatment. Fourier-transform infrared spectra and N2 adsorption suggested that the number of acidic and basic groups in the STL surface increased after the treatment, but the surface area and pore volume remained unchanged.

  20. Design and testing of 45 kV, 50 kHz pulse power supply for dielectric barrier discharges.

    Science.gov (United States)

    Sharma, Surender Kumar; Shyam, Anurag

    2016-10-01

    The design, construction, and testing of high frequency, high voltage pulse power supply are reported. The purpose of the power supply is to generate dielectric barrier discharges for industrial applications. The power supply is compact and has the advantage of low cost, over current protection, and convenient control for voltage and frequency selection. The power supply can generate high voltage pulses of up to 45 kV at the repetitive frequency range of 1 kHz-50 kHz with 1.2 kW input power. The output current of the power supply is limited to 500 mA. The pulse rise time and fall time are less than 2 μs and the pulse width is 2 μs. The power supply is short circuit proof and can withstand variable plasma load conditions. The power supply mainly consists of a half bridge series resonant converter to charge an intermediate capacitor, which discharges through a step-up transformer at high frequency to generate high voltage pulses. Semiconductor switches and amorphous cores are used for power modulation at higher frequencies. The power supply is tested with quartz tube dielectric barrier discharge load and worked stably. The design details and the performance of the power supply on no load and dielectric barrier discharge load are presented.

  1. Numerical simulation of super-short pulsed discharge in helium with particle-in-cell Monte Carlo collisions technique

    Institute of Scientific and Technical Information of China (English)

    Shi Feng; Zhang Li-Li; Wang De-Zhen

    2009-01-01

    This paper reports that a simulation of glow discharge in pure helium gas at the pressure of 1.333×103 Pa under a high-voltage nanosecond pulse is performed by using a one-dimensional particle-in-cell Monte Carlo collisions (PIC-MCC) model. Numerical modelling results show that the cathode sheath is much thicker than that of anode during the pulse discharge, and that there exists the phenomenon of field reversal at relative high pressures near the end of the pulse, which results from the cumulative positive charges due to their finite mobility during the cathode sheath expansion. Moreover, electron energy distribution function (EEDF) and ion energy distribution function (IEDF) have been also observed. In the early stage of the pulse, a large amount of electrons can be accelerated above the ionization threshold energy. However, in the second half of the pulse, as the field in bulk plasma decreases and thereafter the reverse field forms due to the excessive charges in cathode sheath, although the plasma density grows, the high energy part of EEDF decreases. It concludes that the large volume non-equilibrium plasmas can be obtained with high-voltage nanosecond pulse discharges.

  2. The Effect of NaCl/pH on Colloidal Nanogold Produced by Pulsed Spark Discharge

    Directory of Open Access Journals (Sweden)

    Kuo-Hsiung Tseng

    2015-01-01

    Full Text Available A green method, using pulsed spark discharge (PSD to synthesize colloidal gold, is studied in this thesis. PSD uses spark discharge to synthesize gold nanoparticles (AuNPs in deionized water (DIW and/or ethanol (EtOH. While gold nanoparticles have widespread applications in many fields, especially for the human body, in use them must overcome the influence of NaCl and pH value; therefore, this study adds NaCl into PSD-AuNPs to simulate the human body to study its stability. Furthermore, a variety of protectants are added in an attempt to determine the best protectant for AuNPs and improve biologically compatible potency. From the results of this study, adding the long-chain-polymer Carboxymethyl cellulose (CMC or Polyvinyl pyrrolidone (PVP-k30 can prevent nanogold from aggregation and precipitation in NaCl or different pH value and maintain the characteristic of nanogold dispersion by raising the repulsive force between the particles. The results of this study can be a reference of nanogold applying in biomedical science.

  3. Mechanism of formation of subnanosecond current front in high-voltage pulse open discharge

    Science.gov (United States)

    Schweigert, I. V.; Alexandrov, A. L.; Zakrevsky, Dm. E.; Bokhan, P. A.

    2014-11-01

    The mechanism of subnanosecond current front rise observed previously in the experiment in high-voltage pulse open discharge in helium is studied in kinetic particle-in-cell simulations. The Boltzmann equations for electrons, ions, and fast atoms are solved self-consistently with the Poisson equations for the electrical potential. The partial contributions to the secondary electron emission from the ions, fast atoms, photons, and electrons, bombarding the electrode, are calculated. In simulations, as in the experiment, the discharge glows between two symmetrical cathodes and the anode grid in the midplane at P =6 Torr and the applied voltage of 20 kV. The electron avalanche development is considered for two experimental situations during the last stage of breakdown: (i) with constant voltage and (ii) with decreasing voltage. For case (i), the subnanosecond current front rise is set by photons from the collisional excitation transfer reactions. For the case (ii), the energetic electrons swamp the cathode during voltage drop and provide the secondary electron emission for the subnanosecond current rise, observed in the experiment.

  4. Universal and discriminative detection using a miniaturized pulsed discharge detector in comprehensive two-dimensional GC.

    Science.gov (United States)

    Winniford, Bill L; Sun, Kefu; Griffith, James F; Luong, Jim C

    2006-11-01

    A miniaturized pulsed discharge detector (Mini-PDD) has been successfully demonstrated for comprehensive 2-D GC (GC x GC) analysis of pyrolysis gasoline and the pyrolysis GC x GC analysis of a polyethylene copolymer. The detector cell volume of the Mini-PDD is reduced to 25% of the Valco plug-in PDD D-3. An n-C11 peak width at base is 96 ms for the Mini-PDD, about 23% larger than a peak width of 78 ms detected by a flame ionization detector (FID). The Mini-PDD has sufficient response time for most GC x GC applications. When Mini-PDD is operated in helium photoionization mode (Mini He-PDD), it is a universal detector for both inorganic and organic compounds. This is especially useful when detection of water is needed in GC x GC applications. When krypton is doped in the helium discharge gas (Mini Kr-PDD), it can suppress signals of compounds having higher ionization potentials and enhance relative signal intensities of aromatic compounds. The determination of aliphatic to aromatic hydrocarbon ratios is essential to the operation of petroleum crackers. Comparison of the signal from two modes of the Mini-PDD is a simple and fast way to verify the location of aromatics in comprehensive 2-D gas chromatograms.

  5. Physical mechanism of initial breakdown pulses and narrow bipolar events in lightning discharges

    Science.gov (United States)

    Silva, Caitano L.; Pasko, Victor P.

    2015-05-01

    To date the true nature of initial breakdown pulses (IBPs) and narrow bipolar events (NBEs) in lightning discharges remains a mystery. Recent experimental evidence has correlated IBPs to the initial development of lightning leaders inside the thundercloud. NBE wideband waveforms resemble classic IBPs in both amplitude and duration. Most NBEs are quite peculiar in the sense that very frequently they occur in isolation from other lightning processes. The remaining fraction, 16% of positive polarity NBEs, according to Wu et al. (2014), happens as the first event in an otherwise regular intracloud lightning discharge. These authors point out that the initiator type of NBEs has no difference with other NBEs that did not start lightning, except for the fact that they occur deeper inside the thunderstorm (i.e., at lower altitudes). In this paper, we propose a new physical mechanism to explain the source of both IBPs and NBEs. We propose that IBPs and NBEs are the electromagnetic transients associated with the sudden (i.e., stepwise) elongation of the initial negative leader extremity in the thunderstorm electric field. To demonstrate our hypothesis a novel computational/numerical model of the bidirectional lightning leader tree is developed, consisting of a generalization of electrostatic and transmission line approximations found in the literature. Finally, we show how the IBP and NBE waveform characteristics directly reflect the properties of the bidirectional lightning leader (such as step length, for example) and amplitude of the thunderstorm electric field.

  6. Effect of annealing process on TiN/TiC bilayers grown by pulsed arc discharge

    Energy Technology Data Exchange (ETDEWEB)

    Ramos-Rivera, L., E-mail: lramosr@unal.edu.co [Laboratorio de Fisica del Plasma, Universidad Nacional de Colombia Sede Manizales, Km. 9 via al Aeropuerto Campus La Nubia (Colombia); Escobar, D.; Benavides-Palacios, V.; Arango, P.J.; Restrepo-Parra, E. [Laboratorio de Fisica del Plasma, Universidad Nacional de Colombia Sede Manizales, Km. 9 via al Aeropuerto Campus La Nubia (Colombia)

    2012-08-15

    In this work, a study of annealing process effect on TiN/TiC bilayer is presented. The annealing temperature was varied between room temperature and 500 Degree-Sign C. Materials were produced by the plasma-assisted pulsed vacuum arc discharge technique. In order to grow the films, a target of Ti with 99.9999% purity and stainless-steel 304 substrate were used. For the production of TiN layer, the reaction chamber was filled up with nitrogen gas until reaching 25 Pa and the discharge was performed at 310 V. The TiC layer was grown in a methane atmosphere at 30 Pa and 270 V. X-ray diffraction and X photoelectron spectroscopy were employed for studying the structure and chemical composition evolution during the annealing process. At 400 Degree-Sign C, TiO{sub 2} phase begun to appear and it was well observed at 500 Degree-Sign C. Crystallite size and microstrain was obtained as a function of the annealing temperature. XPS technique was employed for analyzing the bilayers before and after the annealing process. Narrow spectra of Ti2p, N1s and O1s were obtained, presenting TiO phases.

  7. Timing of Newborn Pulse Oximetry Screenings for Critical Congenital Heart Defects Before Discharge.

    Science.gov (United States)

    Crouch, Lynn; Speroni, Karen Gabel; Jones, Ruth Ann; MacDougall, Eileen P; Daniel, Marlon G

    2016-01-01

    To determine if there would be positive results from a second pulse oximetry screening (POS) completed for newborns at discharge at 28 to 48 hours of age in addition to the newborn POS completed at 24 to 25 hours of age. Prospective descriptive research study. Rural, mid-Atlantic, 13-bed, level I hospital. Newborns (N = 1,002) at 35 weeks' gestation or older discharged from the newborn nursery. Registered nurses (RNs) performed POS at 24 to 25 hours of age (POS 1) and at discharge but less than 48 hours of age (POS 2). Data related to critical congenital heart defects were collected. There were no positive POS results (O2 saturation ≤ 90%) at POS 1 or POS 2, and no additional diagnostic tests were ordered as a result of POS. Although one full-term newborn had negative results at POS 1 and POS 2, the RN identified a murmur, and a subsequent echocardiogram was used to detect tetralogy of Fallot and pulmonary atresia. The RNs detected concerning conditions in 14 newborns that resulted in 28 additional tests, including echocardiograms (9), chest x-ray imaging (8), laboratory testing (7), electrocardiograms (3), and ultrasound imaging (1). The POS-positive result rate was 0 for newborns at POS 1 and POS 2. Therefore, our study findings supported Maryland's mandate of one POS completed within 24 to 48 hours of birth. Nurses must continue to be vigilant about assessing newborns, including screening for critical congenital heart defects and congenital heart defects. Copyright © 2016 AWHONN, the Association of Women's Health, Obstetric and Neonatal Nurses. Published by Elsevier Inc. All rights reserved.

  8. Evaluation of a pulse-discharge helium ionisation detector for the determination of neon concentrations by gas chromatography.

    Science.gov (United States)

    Lasa, J; Mochalski, P; Pusz, J

    2004-05-07

    A pulse-discharge helium ionisation detector, PDHID (Valco, PD-D2-I) with sample introduced to the discharge zone is shown to be applicable for reliable determinations of neon by gas chromatography. The detection level of 80 pg was obtained, but the dependence between detector response and neon mass was non-linear. However, for the discharge gas doped with 33 ppm of neon, a linear response to the neon mass up to 10(-5) g and the detection level of 0.5 ng were obtained. The method can be used for measuring neon concentrations in groundwater systems for hydrogeological purposes.

  9. Preliminary study on heat load using calorimetric measurement during long-pulse high-performance discharges on EAST

    Science.gov (United States)

    Liu, Y. K.; Hamada, N.; Hanada, K.; Gao, X.; Liu, H. Q.; Yu, Y. W.; Qian, J. P.; Yang, L.; Xu, T. J.; Jie, Y. X.; Yao, Y.; Wang, S. S.; Xu, J. C.; Yang, Z. D.; Li, G. S.; EAST Team

    2017-04-01

    Experimental Advanced Superconducting Tokamak (EAST) aims to demonstrate steady-state advanced high-performance H-mode plasmas with an ITER-like configuration, plasma control and heating schemes. The plasma-facing components in EAST are actively cooled, providing good conditions for researching long-pulse and high-energy discharges. A long-pulse high-performance plasma discharge (#59892 discharge) of up to 103 s with a core electron temperature of up to 4.5 keV was sustained with an injected energy exceeding 0.22 GJ in the 2015–2016 experimental campaign. A calorimetric measurement utilizing the temperature increment of cooling water is carried out to calculate the heat load on the strike point region of the lower divertor during long-pulse discharges in EAST. For the long-pulse and high-energy discharges, the comparison of the measurement results for the heat load measured by divertor Langmuir probes and the calorimetry diagnostic indicates that most of the heat load is delivered to the divertor panels as plasma, not radiation, and charge exchange neutrals. The ratio of the heat load on the strike point region of the lower divertor to the total injected energy is on average 42.5% per discharge with the lower single null divertor configuration. If the radiated energy loss measured by the fast bolometer diagnostic is taken into consideration, the ratio is found to be 61.6%. The experimental results and the analysis of the physics involved in these discharges are reported and discussed.

  10. Corona Borealis

    Science.gov (United States)

    Murdin, P.

    2000-11-01

    (the Northern Crown; abbrev. CrB, gen. Coronae Borealis; area 179 sq. deg.) A northern constellation which lies between Boötes and Hercules, and culminates at midnight in mid-May. It represents the crown that in Greek mythology was made by Hephaestus, god of fire, and worn by Princess Ariadne of Crete. Its brightest stars were cataloged by Ptolemy (c. AD 100-175) in the Almagest....

  11. Activation of peroxydisulfate by gas-liquid pulsed discharge plasma to enhance the degradation of p-nitrophenol

    Science.gov (United States)

    Shang, Kefeng; Wang, Hao; Li, Jie; Lu, Na; Jiang, Nan; Wu, Yan

    2017-06-01

    Pulsed discharge in water and over water surfaces generates ultraviolet radiation, local high temperature, shock waves, and chemical reactive species, including hydroxyl radicals, hydrogen peroxide, and ozone. Pulsed discharge plasma (PDP) can oxidize and mineralize pollutants very efficiently, but high energy consumption restricts its application for industrial wastewater treatment. A novel method for improving the energy efficiency of wastewater treatment by PDP was proposed, in which peroxydisulfate (PDS) was added to wastewater and PDS was activated by PDP to produce more strong oxidizing radicals, including sulfate radicals and hydroxyl radicals, leading to a higher oxidation capacity for the PDP system. The experimental results show that the increase in solution conductivity slightly decreased the discharge power of the pulse discharge over the water surface. An increase in the discharge intensity improved the activation of PDS and therefore the degradation efficiency and energy efficiency of p-nitrophenol (PNP). An increase in the addition dosage of PDS greatly facilitated the degradation of PNP at a molar ratio of PDS to PNP of lower than 80:1, but the performance enhancement was no longer obvious at a dosage of more than 80:1. Under an applied voltage of 20 kV and a gas discharge gap of 2 mm, the degradation efficiency and energy efficiency of the PNP reached 90.7% and 45.0 mg kWh-1 for the plasma/PDS system, respectively, which was 34% and 18.0 mg kWh-1 higher than for the discharge plasma treatment alone. Analysis of the physical and chemical effects indicated that ozone and hydrogen peroxide were important for PNP degradation and UV irradiation and heat from the discharge plasma might be the main physical effects for the activation of PDS.

  12. Plasma-chemical reactor based on a low-pressure pulsed arc discharge for synthesis of nanopowders

    Science.gov (United States)

    Karpov, I. V.; Ushakov, A. V.; Lepeshev, A. A.; Fedorov, L. Yu.

    2017-01-01

    A reactor for producing nanopowders in the plasma of a low-pressure arc discharge has been developed. As a plasma source, a pulsed cold-cathode arc evaporator has been applied. The design and operating principle of the reactor have been described. Experimental data on how the movement of a gaseous mixture in the reactor influences the properties of nanopowders have been presented.

  13. Ozone generation in a kHz-pulsed He-O2 capillary dielectric barrier discharge operated in ambient air

    Science.gov (United States)

    Sands, Brian L.; Ganguly, Biswa N.

    2013-12-01

    The generation of reactive oxygen species using nonequilibrium atmospheric pressure plasma jet devices has been a subject of recent interest due to their ability to generate localized concentrations from a compact source. To date, such studies with plasma jet devices have primarily utilized radio-frequency excitation. In this work, we characterize ozone generation in a kHz-pulsed capillary dielectric barrier discharge configuration comprised of an active discharge plasma jet operating in ambient air that is externally grounded. The plasma jet flow gas was composed of helium with an admixture of up to 5% oxygen. A unipolar voltage pulse train with a 20 ns pulse risetime was used to drive the discharge at repetition rates between 2-25 kHz. Using UVLED absorption spectroscopy centered at 255 nm near the Hartley-band absorption peak, ozone was detected over 1 cm from the capillary axis. We observed roughly linear scaling of ozone production with increasing pulse repetition rate up to a "turnover frequency," beyond which ozone production steadily dropped and discharge current and 777 nm O(5P→5S°) emission sharply increased. The turnover in ozone production occurred at higher pulse frequencies with increasing flow rate and decreasing applied voltage with a common energy density of 55 mJ/cm3 supplied to the discharge. The limiting energy density and peak ozone production both increased with increasing O2 admixture. The power dissipated in the discharge was obtained from circuit current and voltage measurements using a modified parallel plate dielectric barrier discharge circuit model and the volume-averaged ozone concentration was derived from a 2D ozone absorption measurement. From these measurements, the volume-averaged efficiency of ozone production was calculated to be 23 g/kWh at conditions for peak ozone production of 41 mg/h at 11 kV applied voltage, 3% O2, 2 l/min flow rate, and 13 kHz pulse repetition rate, with 1.79 W dissipated in the discharge.

  14. Photo-triggering and secondary electron produced ionization in electric discharge ArF* excimer lasers

    Science.gov (United States)

    Xiong, Zhongmin; Kushner, Mark J.

    2011-10-01

    Electric discharge excimer lasers are sustained in multi-atmosphere attaching gas mixtures that are typically preionized to enable a reproducible, uniform glow, which maximizes optical quality and gain. This preionization is often accomplished using UV light produced by a corona discharge within the plasma cavity. To quantify the relationship between corona discharge properties and those of the laser discharge, the triggering of electron avalanche by preionizing UV light in an electric discharge-pumped ArF* excimer laser was numerically investigated using a two-dimensional model. The preionizing UV fluxes were generated by a corona-bar discharge driven by the same voltage pulse as the main discharge sustained in a multi-atmospheric Ne/Ar/Xe/F2 gas mixture. The resulting peak photo-electron density in the inter-electrode spacing is around 108 cm-3, and its distribution is biased toward the UV source. The preionization density increases with increasing dielectric constant and capacitance of the corona bar. The symmetry and uniformity of the discharge are, however, improved significantly once the main avalanche develops. In addition to bulk electron impact ionization, the ionization generated by sheath accelerated secondary electrons was found to be important in sustaining the discharge current at experimentally observed values. At peak current, the magnitude of the ionization by sheath accelerated electrons is comparable to that from bulk electron impact in the vicinity of the cathode.

  15. Discharge conditions for CW and pulse-modulated surface-wave plasmas in low-temperature sterilization

    Energy Technology Data Exchange (ETDEWEB)

    Xu, L [Department of Electrical and Electronic Engineering, Faculty of Engineering, Shizuoka University, 3-5-1 Johoku, Hamamatsu 432-8561 (Japan); Terashita, F [Department of Electrical and Electronic Engineering, Faculty of Engineering, Shizuoka University, 3-5-1 Johoku, Hamamatsu 432-8561 (Japan); Nonaka, H [Department of Electrical and Electronic Engineering, Faculty of Engineering, Shizuoka University, 3-5-1 Johoku, Hamamatsu 432-8561 (Japan); Ogino, A [Department of Electrical and Electronic Engineering, Faculty of Engineering, Shizuoka University, 3-5-1 Johoku, Hamamatsu 432-8561 (Japan); Nagata, T [Department of Microbiology and Immunology, Hamamatsu University School of Medicine, 1-20-1 Handa-yama, Hamamatsu 431-3192 (Japan); Koide, Y [Department of Microbiology and Immunology, Hamamatsu University School of Medicine, 1-20-1 Handa-yama, Hamamatsu 431-3192 (Japan); Nanko, S [Nissin Inc., 10-7 Kamei-cho, Takarazuka 665-0047 (Japan); Kurawaki, I [GMA Co. Ltd., 3898-1, Asaba, Fukuroi, 437-1101 (Japan); Nagatsu, M [Department of Electrical and Electronic Engineering, Faculty of Engineering, Shizuoka University, 3-5-1 Johoku, Hamamatsu 432-8561 (Japan)

    2006-01-07

    The discharge conditions required for low-temperature plasma sterilization were investigated using low-pressure surface-wave plasma (SWP). The discharge conditions for both continuous wave (CW) and pulse-modulated SWPs in low-temperature sterilization of Geobacillus stearothermophilus with a population of 1.5 x 10{sup 6} and 3.0 x 10{sup 6} were studied by varying the microwave input power from 500 W to 3 kW, and the effective plasma treatment time from 40 to 300 s. Results showed that sterilization was possible in a shorter treatment time using a higher microwave power for both CW and pulse-modulated SWPs. Pulse-modulated SWPs gave effective sterilization at a temperature roughly 10 to 20 deg. C below that of CW SWPs under the same average microwave power.

  16. Discharge conditions for CW and pulse-modulated surface-wave plasmas in low-temperature sterilization

    Science.gov (United States)

    Xu, L.; Terashita, F.; Nonaka, H.; Ogino, A.; Nagata, T.; Koide, Y.; Nanko, S.; Kurawaki, I.; Nagatsu, M.

    2006-01-01

    The discharge conditions required for low-temperature plasma sterilization were investigated using low-pressure surface-wave plasma (SWP). The discharge conditions for both continuous wave (CW) and pulse-modulated SWPs in low-temperature sterilization of Geobacillus stearothermophilus with a population of 1.5 × 106 and 3.0 × 106 were studied by varying the microwave input power from 500 W to 3 kW, and the effective plasma treatment time from 40 to 300 s. Results showed that sterilization was possible in a shorter treatment time using a higher microwave power for both CW and pulse-modulated SWPs. Pulse-modulated SWPs gave effective sterilization at a temperature roughly 10 to 20 °C below that of CW SWPs under the same average microwave power.

  17. Control of Reactive Species Generated by Low-frequency Biased Nanosecond Pulse Discharge in Atmospheric Pressure Plasma Effluent

    Science.gov (United States)

    Takashima, Keisuke; Kaneko, Toshiro

    2016-09-01

    The control of hydroxyl radical and the other gas phase species generation in the ejected gas through air plasma (air plasma effluent) has been experimentally studied, which is a key to extend the range of plasma treatment. Nanosecond pulse discharge is known to produce high reduced electric field (E/N) discharge that leads to efficient generation of the reactive species than conventional low frequency discharge, while the charge-voltage cycle in the low frequency discharge is known to be well-controlled. In this study, the nanosecond pulse discharge biased with AC low frequency high voltage is used to take advantages of these discharges, which allows us to modulate the reactive species composition in the air plasma effluent. The utilization of the gas-liquid interface and the liquid phase chemical reactions between the modulated long-lived reactive species delivered from the air plasma effluent could realize efficient liquid phase chemical reactions leading to short-lived reactive species production far from the air plasma, which is crucial for some plasma agricultural applications.

  18. Detection and removal of impurities in nitric oxide generated from air by pulsed electrical discharge.

    Science.gov (United States)

    Yu, Binglan; Blaesi, Aron H; Casey, Noel; Raykhtsaum, Grigory; Zazzeron, Luca; Jones, Rosemary; Morrese, Alexander; Dobrynin, Danil; Malhotra, Rajeev; Bloch, Donald B; Goldstein, Lee E; Zapol, Warren M

    2016-11-30

    Inhalation of nitric oxide (NO) produces selective pulmonary vasodilation without dilating the systemic circulation. However, the current NO/N2 cylinder delivery system is cumbersome and expensive. We developed a lightweight, portable, and economical device to generate NO from air by pulsed electrical discharge. The objective of this study was to investigate and optimize the purity and safety of NO generated by this device. By using low temperature streamer discharges in the plasma generator, we produced therapeutic levels of NO with very low levels of nitrogen dioxide (NO2) and ozone. Despite the low temperature, spark generation eroded the surface of the electrodes, contaminating the gas stream with metal particles. During prolonged NO generation there was gradual loss of the iridium high-voltage tip (-90 μg/day) and the platinum-nickel ground electrode (-55 μg/day). Metal particles released from the electrodes were trapped by a high-efficiency particulate air (HEPA) filter. Quadrupole mass spectroscopy measurements of effluent gas during plasma NO generation showed that a single HEPA filter removed all of the metal particles. Mice were exposed to breathing 50 parts per million of electrically generated NO in air for 28 days with only a scavenger and no HEPA filter; the mice did not develop pulmonary inflammation or structural changes and iridium and platinum particles were not detected in the lungs of these mice. In conclusion, an electric plasma generator produced therapeutic levels of NO from air; scavenging and filtration effectively eliminated metallic impurities from the effluent gas. Copyright © 2016 Elsevier Inc. All rights reserved.

  19. 空腔水电极电晕放电雾化特性的研究%Study on Spray Characteristics of Corona Discharge on Cavity-Type Hydro Pole

    Institute of Scientific and Technical Information of China (English)

    刘志强; 王霁光; 李庆; 张文月; 孙晓荣

    2011-01-01

    Atomization of corona discharge has potential applications in electrostatic dust removal,pesticide spraying and other fields. To investigate the gas-liquid two-phase flow discharge characteristics, the cavity-type spray electrode was used in the experiment for the first time. By measuring the voltage-current characteristics of different atomization poles, water consumption with different concentration of solution and other physical parameters, the discharge characteristics of cavity-type spray electrode were analyzed. Experiments show that, in the condition of dry electrode, the smaller the curvature radius of the cavity-type electrode, the larger the discharge current, and the current difference increases with the increase of voltage. In the condition of atomization corona discharge, electrode shape or concentration of the solution has no obvious effect on the discharge current, but has more significant effect on the consumption of the solution. The form of atomization under different voltages is various and the dynamics process of the droplet in electric field is also different.%为了研究气-液两相流的空间放电特性规律,实验首次采用空腔水电极雾化装置,通过测量不同雾化电极的电压-电流特性,不同质量分数溶液雾化时的消耗量等物理参量,分析了空腔水电极电晕放电的特性.实验表明,空腔电极在干式电晕放电时,曲率半径越小,放电电流越大,且随着电压升高,电流差值呈上升趋势;在雾化电晕放电时,电极形状、溶液质量分数对放电电流影响不明显,对溶液消耗量影响较为显著;不同电压作用下的雾化形式不同,雾滴在电场中的动力学过程也不同.

  20. Dynamic Characteristics of Positive Pulsed Dielectric Barrier Discharge for Ozone Generation in Air

    Science.gov (United States)

    Wei, Linsheng; Peng, Bangfa; Li, Ming; Zhang, Yafang; Hu, Zhaoji

    2016-02-01

    A comprehensive dynamic model consisting of 66 reactions and 24 species is developed to investigate the dynamic characteristics of ozone generation by positive pulsed dielectric barrier discharge (DBD) using parallel-plate reactor in air. The electron energy conservation equation is coupled to the electron continuity equation, the heavy species continuity equation, and Poisson's equation for a better description. The reliability of the model is experimentally confirmed. The model can be used to predict the temporal and spatial evolution of species, as well as streamer propagation. The simulation results show that electron density increases nearly exponentially in the direction to the anode at the electron avalanche. Streamer propagation velocity is about 5.26 × 104 m/s from anode to cathode in the simulated condition. The primary positive ion, negative ion, and excited species are O2+, O3- and O2(1Δg) in pulsed DBD in air, respectively. N2O has the largest density among nitrogen oxides. e and N2+ densities in the streamer head increase gradually to maximum values with the development of the streamer. Meanwhile, the O2+, O, O3, N2(A3Σ) and N2O densities reach maximum values in the vicinity of the anode. supported by National Natural Science Foundation of China (Nos. 51366012 and 11105067), Jiangxi Province Young Scientists (Jinggang Star) Cultivation Plan of China (No. 20133BCB23008), Natural Science Foundation of Jiangxi, China (No. 20151BAB206047) and Jiangxi Province Higher School Science and Technology Landing Plan of China (No. KJLD-14015)