Acid-base synergistic flame retardant wood pulp paper with high thermal stability.

Science.gov (United States)

Wang, Ning; Liu, Yuansen; Xu, Changan; Liu, Yuan; Wang, Qi

2017-12-15

Acid-catalytic degradation caused by acid source flame retardants is the main reason for a decline in thermal stability of flame-retarded lignocellulosic materials. In the present research, a guanidine phosphate (GP)/borax (BX) flame retardant system based on acid-base synergistic interaction was designed and used in wood pulp paper (WPP) to solve this problem. Results showed that the treated WPP obtained good flame retardancy with a limiting oxygen index (LOI) value of 35.7%. As a basic flame retardant, borax could chemically combine with the acids released by guanidine phosphate, thus decreasing the acidity of the system in the initial heating stage. In this way, acid-catalytic degradation is greatly retarded on the lignocelluloses to improve thermal stability (the temperature of maximum degradation peak from 286°C to 314°C). Meanwhile, borax was also advantageous to form a denser and firmer condensed phase through reinforcement of the acid-base reaction product, borophosphates, allowing it to provide a protective barrier with higher quality. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of fluoride varnishes on color stability of esthetic restorative materials.

Science.gov (United States)

Autio-Gold, Jaana T; Barrett, Allyson A

2004-01-01

Fluoride varnish applications were applied to two hybrid resin composite materials, Z-100 (3M Dental Products, St Paul, MN, USA) and Esthet-X (Dentsply Caulk, Milford, DE, USA), shades A1 and A2 and a glass ionomer, GC Fuji IX GP Fast (GC Corporation, Tokyo, Japan), shade A2, to evaluate color stability. Specimens (12.6-mm dia x 2.3 mm) were prepared using a polyethylene frame, light-cured and polished through a 1-microm alumina finish. After the initial baseline color measurements, the discs were suspended in Fusayama artificial saliva (FAS) solution at 37 degrees C for 48 hours. Post immersion, the specimens were divided into five groups (n=15 each). The following fluoride varnishes were applied to four groups of test specimens: Duraphat (Colgate Oral Pharmaceutical, Inc, Canton MA, USA), Cavity Shield (OMNII Oral Pharmaceuticals, West Palm Beach, FL, USA), Duraflor (Pharmascience Inc, Montreal, Canada) and Fluor Protector (Vivadent, Ivoclar North America, Amherst, NY, USA). The varnish was allowed to dry for five minutes before immersion. The control group was not coated with varnish, although the specimens were immersed in FAS. All specimens were incubated in newly prepared FAS at 37 degrees C for 24 hours, cleaned with an electric toothbrush and the process repeated using newly prepared FAS. CIE L*a*b* color measurements were recorded five times: at baseline, after 48 hours FAS immersion, after cleaning the first and second fluoride varnish applications and after the final brushing using a commercial toothpaste (Crest). A Minolta CR-300 tristimulus colorimeter with an 8-mm aperture (Ramsey, NJ, USA) was used to record color measurements with the daylight (D65) setting. Calculations were performed for using CIE parameters deltaE*, deltaL*, delta a*, delta b*. Analysis of variance (ANOVA) and post-hoc test (Fisher's PLSD) were used for statistical analysis. After immersion in saliva, the tested glass ionomer (Fuji IX) produced the most significant color changes

Color stability of restorative materials in response to Arabic coffee, Turkish coffee and Nescafe.

Science.gov (United States)

Al-Samadani, Khalid H

2013-07-01

To evaluate the effect of Arabic coffee, Turkish coffee and Nescafe on the color stability of four different composite resins after a period of aging time 1, 7 and 30 days. Twenty specimens from each type of tested composite resin material were prepared. Five specimens from each tested material (Z350 XT, Artist, GC and Z250) was evaluated after storage in Arabic coffee, Turkish coffee, Nescafe and distil water (control) at 37°C in a dark container for 1, 7 and 30 days. Color measurement was done using colorimeter based on the CIE L* a* b* color scale. Color differences ΔE*ab, Δb* and Δa* among specimens immersed in distil water and staining coffee beverages were evaluated overtime. Mean values were statistically analyzed with one-way analysis of variance (ANOVA), followed by Tukey test with p Nescafe except Δa*. The highest total color difference ΔE*ab after 30 days was in group A Arabic coffee (ΔE > 1.5 perceivable) and not perceivable in group B Turkish coffee and group C Nescafe. For Δb* all materials discolored toward yellowness after 30 days except Arabic coffee group which shifted from yellowness toward blueness (Δb*> 1.5 perceivable). The effect of staining beverages on the resin composite materials increases with time of aging toward yellowness and not perceivable in all groups except with Arabic coffee which had highest effect after 30 days and the discoloration shifted from yellowness to blueness perceivable.

Mesta/Kenaf as raw material for Kraft pulping

Energy Technology Data Exchange (ETDEWEB)

Saraf, V. P.; Shiveshwar, R. M.; Meshramkar, P. M.; Deb, U. K.; Jaspal, N. S.; Biyani, B. P.

1980-03-15

In recent years, the shortage of conventional raw materials for pulping has intensified a world-wide search for alternate raw materials. Among other cellulosic materials, attention has focused on agricultural residues and annual plants. In this category, Kenaf, also called Mesta, has been studied as a fiber source in many countries including the USA, Phillippines and India. A comprehensive study on kraft pulping of mesta was carried out where the fiber morphology, pulping, bleaching and papermaking characteristics were investigated. Black liquor properties were also determined. The results of this study are reported and compared to the conventional raw material bamboo. The investigation has shown that mesta is easily pulped and bleached and forms sheets of excellent strength properties, comparable to or better than bamboo pulps. The black liquor from mesta is similar to bamboo in calorific value but is very low in silica, which is highly desirable from the chemical recovery point of view. As with all agricultural residues and annual plants, mesta has a high bulk per unit weight. The problems arising from this, e.g., baling, transportation, proper utilization of digester capacity, have to be studied before mesta can be widely accepted in the paper industry.

Evaluation of the effect of various beverages and food material on the color stability of provisional materials - An in vitro study.

Science.gov (United States)

Gupta, Gaurav; Gupta, Tina

2011-07-01

THIS STUDY EVALUATED THE COLOR STABILITY OF FOUR PROVISIONAL MATERIALS: 1) Poly-methyl methacrylates (DPI); 2) Bis-acryl composite (ProtempTM II - 3M ESPE); 3) Bis-acryl composite (Systemp® c and b - Ivoclar Vivadent) and 4) Light polymerized composite resin (Revotek LC- GC). The color and color difference of each specimen after immersion in different staining solutions i.e. 1) tea and artificial saliva, 2) coffee and artificial saliva, 3) Pepsi and artificial saliva, 4) turmeric solution and artificial saliva was measured using reflectance spectrophotometer with CIELAB system before immersion and after immersion at 2, 5 ,7 , 10 and 15 days. Revotek LC- GC (light polymerized composite resin) was found to be the most color stable provisional restorative material followed by Protemp II (Bis-acryl composite), Systemp (Bis-acryl composite) and DPI (Methylmethacrylate resin). Turmeric solution had the maximum staining potential followed by coffee, tea and Pepsi.

Evaluation of the effect of various beverages and food material on the color stability of provisional materials – An in vitro study

Science.gov (United States)

Gupta, Gaurav; Gupta, Tina

2011-01-01

Aim: This study evaluated the color stability of four provisional materials: 1) Poly-methyl methacrylates (DPI); 2) Bis-acryl composite (ProtempTM II – 3M ESPE); 3) Bis-acryl composite (Systemp® c and b – Ivoclar Vivadent) and 4) Light polymerized composite resin (Revotek LC- GC). Materials and Methods: The color and color difference of each specimen after immersion in different staining solutions i.e. 1) tea and artificial saliva, 2) coffee and artificial saliva, 3) Pepsi and artificial saliva, 4) turmeric solution and artificial saliva was measured using reflectance spectrophotometer with CIELAB system before immersion and after immersion at 2, 5 ,7 , 10 and 15 days. Results: Revotek LC- GC (light polymerized composite resin) was found to be the most color stable provisional restorative material followed by Protemp II (Bis-acryl composite), Systemp (Bis-acryl composite) and DPI (Methylmethacrylate resin). Turmeric solution had the maximum staining potential followed by coffee, tea and Pepsi. PMID:22025835

Transcriptomic analysis reveals key genes related to betalain biosynthesis in pulp coloration of Hylocereus polyrhizus

Directory of Open Access Journals (Sweden)

Hua eQingzhu

2016-01-01

Full Text Available Betalains have high nutritional value and bioactivities. Red pulp pitaya (Hylocereus polyrhizus is the only fruit containing abundant betalains for consumer. However, no information is available about genes involved in betalain biosynthesis in H. polyrhizus. Herein, two cDNA libraries of pitaya pulps with two different coloration stages (white and red pulp stages of Guanhuahong (H. polyrhizus were constructed. A total of about 12 Gb raw RNA-Seq data was generated and was de novo assembled into 122,677 transcripts with an average length of 1,183 bp and an N50 value of 2008. Approximately 99.99% of all transcripts were annotated based on seven public databases. A total of 8,871 transcripts were significantly regulated. Thirty-three candidate transcripts related to betalain biosynthesis were obtained from the transcriptome data. Transcripts encoding enzymes involved in betalain biosynthesis were analyzed using RT-qPCR at the whole pulp coloration stages of H. Polyrhizus (7-1 and H. Undatus (132-4. Nine key transcripts of betalain biosynthesis were identified. They were assigned to four kinds of genes in betalain biosynthetic pathway, including tyrosinase, 4, 5-DOPA dioxygenase extradiol, cytochrome P450 and glucosyltransferase. Ultimately, a preliminary betalain biosynthetic pathway for pitaya was proposed based on betalain analyses and gene expression profiles.

Long-term microwaving of denture base materials: effects on dimensional, color and translucency stability

Directory of Open Access Journals (Sweden)

Nick POLYCHRONAKIS

2018-06-01

Full Text Available Abstract While the combined effect of microwave irradiation with cleansing solutions on denture base materials has been investigated, the effects of only using microwave irradiation and, more importantly, in a long-term basis, was not studied yet. Objective The purpose of this study was to evaluate the effect of a long-term repeated microwaving on the dimensional, color and translucency stability of acrylic and polyamide denture base materials. Material and Methods Thirty two specimens (32 mm x 10 mm x 2.5 mm from polyamide (Valplast and PMMA (Vertex Rapid Simplified denture base materials were made. Eight specimens from each material were immersed in distilled water (control and 8 were subjected to microwave exposure at 450 W for 3 minutes for a period simulating 224 days of daily disinfection. Linear dimension, color change (ΔE* and translucency parameter (TP were measured at baseline and after certain intervals up to 224 cycles of immersion, using a digital calliper and a portable colorimeter. The results were analysed using two-way repeated measures ANOVA to estimate possible differences among predetermined cycles and material type. Regression analysis was also performed to estimate the trend of changes with time. Statistical evaluations performed at a significance level of 5%. Results Data analysis showed significant changes in length at baseline with an increasing number of cycles (p0.05. TP decreased similarly in both materials following microwave action but in a significantly higher level for Valplast (p<0.001. Conclusions The results indicated that long-term repeated microwaving affects linear dimensional, color and translucency changes of both materials. Differences between PMMA and polyamide material were noted only in dimension and translucency changes.

The Effects of Natural Weathering on Color Stability of Impregnated and Varnished Wood Materials

Directory of Open Access Journals (Sweden)

Turkay Turkoglu

2015-01-01

Full Text Available The aim of this study was to investigate effects of natural weathering on color stability of Scots pine (Pinus sylvestris L. and Oriental beech (Fagus orientalis L. impregnated with some chemicals [tanalith-E (TN-E, adolit-KD5 (AD-KD5, and chromated copper arsenate (CCA] and then varnished [synthetic varnish (SV and polyurethane varnish (PV]. While applying varnish increased lightness, impregnation decreased lightness of the wood specimens before natural weathering. Natural weathering caused greenish, bluish, and dark color tones of the wood surface. Total color change was increased with increasing exposure times in natural weathering. Untreated (control wood specimens exhibited higher color changes than the other wood specimens in all the stages of natural weathering. The total color changes of untreated Oriental beech specimens were less than untreated Scots pine specimens. The color stability of impregnated and varnished wood specimens gave better results than untreated and solely varnished wood specimens after natural weathering. The best color stability was obtained from both Oriental beech and Scots pine wood impregnated with TN-E before PV coating.

Biodegradation behaviors and color change of composites based on type of bagasse pulp/polylactic acid

Directory of Open Access Journals (Sweden)

maryam allahdadi

2017-05-01

Full Text Available In this research, appearance quality and decay resistance of polylactic acid (PLA based green composites made from monoethanolamine (MEA bagasse pulp, alkaline sulfite-anthraquinone (AS bagasse pulp, bleached soda (B S bagasse pulp, unbleached soda (UN S bagasse pulp (UN S bagasse pulp and raw bagasse fibers (B were investigated. For the investigation of biodegradation behaviors, effect of the white rot fungi (Coriolus versicolor on the neat PLA and composites with natural fibers during 30 and 60 days were studied. It is found that when the bagasse fibers were incorporated into composites matrix, percentage weight reduction and stiffness of samples have been increased. Also, the rate of loss mentioned of the composites made from bagasse pulp fibers were superior to the relevant raw bagase fibers. This can be explained by the removal of non-cellulosic components such as lignin and hemicelluloses from the fibers by pulping process. Also, the results indicates the inferior of surface qualities of fabricated composites regarding to neat PLA. Depending on the fiber type, different reductions of the surface qualities were attained. However, the degree of color change of the composites with any type of bagasse pulp fibers were lower compared with composite with raw bagasse fiber. Finally, as compared with the raw bagasse fibers, bagasse pulp fibers have better reinforcing capability.

The effect of different drinks on the color stability of different restorative materials after one month

Directory of Open Access Journals (Sweden)

Neslihan Tekçe

2015-11-01

Full Text Available Objectives The aim of this study was to evaluate the effect of three different drinks on the color parameters of four different restorative materials. Materials and Methods Three different composites (Filtek Ultimate Universal Restorative, Filtek Ultimate Flowable, and Filtek Silorane, 3M ESPE and a polyacid-modified composite resin material (Dyract XP, Dentsply DeTrey GmbH were evaluated. Eighty-four disc-shaped specimens of 8 mm in diameter and 2 mm in thickness were prepared (n = 21 each. Color coordinates (L*a*b*, ΔL*, Δa*, Δb*, and ΔE* were measured using a VİTA Easyshade Compact (VİTA Zahnfabrik after 24 hr of storage (baseline and after 30 day of storage in three different beverages of black tea, Coca cola, or water (control (n = 7. In each beverage, the specimens were stored three times a day, one hr each, for 30 day. The color changes (ΔE were calculated and were analyzed by Kruskal-Wallis and Dunn multiple comparison test. Results The color difference (ΔE* of the resin materials ranged between 1.31 and 15.28 after 30 day of immersion in the staining solutions. Dyract XP in Coca cola (15.28 ± 2.61 and black tea (12.22 ± 2.73 showed the highest mean ΔE* value after 30 day, followed by Filtek Ultimate Universal Restorative (5.99 ± 1.25 and Filtek Ultimate Flowable (4.71 ± 1.40 in black tea (p < 0.05. Conclusions The compomers displayed unacceptable color changes at the end of 30 day in all beverages. Among resin composites, the silorane based composite exhibited relatively good color stability than the others. Filtek Ultimate Universal Restorative and Filtek Flowable showed similar color changes in all beverages.

Prospect of trema orientalis as a pulping raw material in bangladesh

International Nuclear Information System (INIS)

Jahan, M.S.

2013-01-01

The pulp and paper industry in Bangladesh is looking for new raw materials with high productivity per hectare. Currently, bamboo and Gmelina arborea are the main pulping raw materials for the pulp and paper industry of the country. Trema orientalis is one of the fastest growing woods in the tropical region. This paper reviews the literature on the topic, in particular, related to the chemical, morphological and physical properties of T. orientalis and its suitability for pulping. In addition, the advantages and disadvantages of various ulping processes proposed in the literature were critically analyzed. It was concluded that T. orientalis is a potential pulp wood for the Bangladesh pulp and paper industry. (author)

The effect of different drinks on the color stability of different restorative materials after one month.

Science.gov (United States)

Tekçe, Neslihan; Tuncer, Safa; Demirci, Mustafa; Serim, Merve Efe; Baydemir, Canan

2015-11-01

The aim of this study was to evaluate the effect of three different drinks on the color parameters of four different restorative materials. Three different composites (Filtek Ultimate Universal Restorative, Filtek Ultimate Flowable, and Filtek Silorane, 3M ESPE) and a polyacid-modified composite resin material (Dyract XP, Dentsply DeTrey GmbH) were evaluated. Eighty-four disc-shaped specimens of 8 mm in diameter and 2 mm in thickness were prepared (n = 21 each). Color coordinates (L*a*b*, ΔL*, Δa*, Δb*, and ΔE*) were measured using a VİTA Easyshade Compact (VİTA Zahnfabrik) after 24 hr of storage (baseline) and after 30 day of storage in three different beverages of black tea, Coca cola, or water (control) (n = 7). In each beverage, the specimens were stored three times a day, one hr each, for 30 day. The color changes (ΔE) were calculated and were analyzed by Kruskal-Wallis and Dunn multiple comparison test. The color difference (ΔE*) of the resin materials ranged between 1.31 and 15.28 after 30 day of immersion in the staining solutions. Dyract XP in Coca cola (15.28 ± 2.61) and black tea (12.22 ± 2.73) showed the highest mean ΔE* value after 30 day, followed by Filtek Ultimate Universal Restorative (5.99 ± 1.25) and Filtek Ultimate Flowable (4.71 ± 1.40) in black tea (p < 0.05). The compomers displayed unacceptable color changes at the end of 30 day in all beverages. Among resin composites, the silorane based composite exhibited relatively good color stability than the others. Filtek Ultimate Universal Restorative and Filtek Flowable showed similar color changes in all beverages.

Color stability of esthetic coatings applied to nickel-titanium archwires

Directory of Open Access Journals (Sweden)

Marcus Vinicius Neiva Nunes do REGO

Full Text Available Abstract Introduction Color stability is an important feature to be considered when using esthetic coated archwires. Objective To evaluate color changes on the surface of esthetic nickel-titanium archwires coated with Teflon (Ortho Organizers, USA or epoxy resin (Tecnident, Brazil after immersion in staining solution. Material and method Twelve 20-mm-long wire segments were used for each type of coating, which were mounted as two test specimens with a width of 7 mm each. The buccal surface of the archwires was evaluated for fluorescence and color measurements both at baseline and after immersion in a staining solution for 21 days using the VITA Easyshade® Compact spectrophotometer (Model DEASYC220. Differences in total color change according to coating type were compared using an independent samples t-test (p<0.05. The surface characteristics of as-received coated archwires were assessed using scanning electron microscopy. Result Color changes were observed on the esthetic coatings, with a significant difference between the two brands analyzed. Surface analysis revealed flaws such as wear, pitting, elevations, lack of material, granulation, grooves, cracks, and lack of standardization in the coating process in all as-received archwires, but flaws were less evident in epoxy-resin coatings. Conclusion The two esthetic coatings did not show color stability, but Teflon coatings showed a more intense color change than epoxy-resin coatings.

Effect of one-step polishing system on the color stability of nanocomposites.

Science.gov (United States)

Alawjali, S S; Lui, J L

2013-08-01

This study was to compare the effect of three different one-step polishing systems on the color stability of three different types of nanocomposites after immersion in coffee for one day and seven days and determine which nanocomposite material has the best color stability following polishing with each of the one-step polishing system. The nanocomposites tested were Tetric EvoCeram, Grandio and Herculite Précis. A total of 120 discs (40/nanocomposite, 8mm×2mm) were fabricated. Ten specimens for each nanocomposite cured under Mylar strips served as the control. The other specimens were polished with OptraPol, OneGloss and Occlubrush immersed in coffee (Nescafé) up to seven days. Color measurements were made with a spectrophotometer at baseline and after one and seven days. Two way repeated measure ANOVA, two way ANOVA and Bonferroni tests were used for statistical analyses (P<0.05). The immersion time was a significant factor in the discoloration of the nanocomposites. The effect of three one-step polishing systems on the color stability was also significant. The color change values of the materials cured against Mylar strips were the greatest. The lowest mean color change values were from the Occlubrush polished groups. The effect of the three different types of nanocomposite on the color change was significant. The highest color change values were with Tetric EvoCeram groups. The lowest color change values were with Herculite Précis groups. The color change of nanocomposite resins is affected by the type of composite, polishing procedure and the period of immersion in the staining agent. Copyright © 2012 Elsevier Ltd. All rights reserved.

Color and opacity of composites protected with surface sealants and submitted to artificial accelerated aging.

Science.gov (United States)

Aguilar, Fabiano Gamero; Roberti Garcia, Lucas da Fonseca; Cruvinel, Diogo Rodrigues; Sousa, Ana Beatriz Silva; de Carvalho Panzeri Pires-de-Souza, Fernanda

2012-01-01

To evaluate the color similarity, stability and opacity of composites (TPH, Charisma, and Concept, shade A2) protected with surface sealants (Fortify Plus and Biscover) and cyanoacrylate (Super Bonder). Forty specimens of each composite were made and separated into 4 groups (n=10) according to the surface protection: GI - without sealant; GII - cyanoacrylate; GIII - Fortify Plus; GIV - Biscover. Color and opacity readings were taken before and after Artificial Acelerated Aging (AAA) and the values obtained for color stability were submitted to statistical analysis by 2-way ANOVA and Bonferroni's test (P<.05). The values acquired for color similarity were submitted to 1-way ANOVA and Tukey's test (P<.05). The specimen sufaces were compared before and after AAA using Scanning Electronic Microscopy (SEM). Studied composites did not present the same values for the coordinates L*, a* and b * before AAA, indicating that there was no color similarity among them. All composites presented color alteration after AAA with clinically unacceptable values. Protected groups presented lower opacity variation after AAA, in comparison with the control goup. SEM evaluation demonstrated that AAA increased the surface irregularities in all of the studied groups. Surface sealants were not effective in maintaining composite color, but were able to maintain opacity.

Color stabilization of red wines. A chemical and colloidal approach.

Science.gov (United States)

Alcalde-Eon, Cristina; García-Estévez, Ignacio; Puente, Victor; Rivas-Gonzalo, Julián C; Escribano-Bailón, M Teresa

2014-07-23

The effects of cold treatment and time on CIELAB color parameters and on anthocyanin and anthocyanin-derived pigments composition have been evaluated as has been the effectiveness of either an enological tannin or a mannoprotein (M) on their stabilization. With respect to color, hue (hab) was increased in the wines treated with both enological products. Furthermore, the color changes induced by cold treatment were lessened by the addition of these two enological products, although the protective effect was higher for the wines treated with M. The pigment analysis revealed higher percentages of anthocyanin-derived pigments in tannin and M-treated samples (in both cold treated and not) in relation to control ones. The addition of the enological tannin may favor the synthesis of anthocyanin-derived pigments, which are chemically more stable than native anthocyanins, whereas M seems to stabilize anthocyanin-derived pigments from a colloidal point of view, avoiding their aggregation and further precipitation.

COLOR STABILITY FOR WOOD PRODUCTS DURING USE: EFFECTS OF INORGANIC NANOPARTICLES

Directory of Open Access Journals (Sweden)

Vincent Blanchard

2011-04-01

Full Text Available Despite significant progress having been achieved in recent years to improve wood’s durability, additional developments are still necessary to increase its color stability. ZnO and CeO2 nanoparticles were compared to UV absorbers (Tinuvin 477 DW, 292 and 5151 commonly used to stabilize the wood products color. Nanoparticles, with concentrations in the range 1 to 2 wt%, and UV absorbers, using concentrations advised by the manufacturer, were dispersed in a waterborne UV curable polyurethane/polyacrylate resin. Dispersions were carried out with a high speed mixer at 2,500 RPM with micro glass beads or not, depending on the form of the nanoparticles. Nanocomposite coatings were aged with a weather-o-meter (CI 3000+ - Atlas according ASTM G155. Color variations were measured with a colorimeter (BYK Gardner – Color Guide 45/0 working with the CIE L*a*b* system. The aim of the present study was to assess the effects of inorganic UV absorbers on the stabilization of color under indoor conditions. Results showed that nanoparticles (ZnO, CeO2 absorbed UV light frequencies in a manner similar to common organic molecules. Their efficiency was better at medium durations of light exposure, for which they could achieve the action of organic absorbers. Finally, the simultaneous use of both absorbers seems to create a protective synergy when degradation is due to UV energy alone.

Nutritional composition and vitamin C stability in stored camu-camu (Myrciaria dubia) pulp.

Science.gov (United States)

Justi, K C; Visentainer, J V; Evelázio de Souza, N; Matsushita, M

2000-12-01

Camu-camu (Myrciaria dubia), a native fruit of the Amazon region, is one of the richest sources of vitamin C (2.4 to 3.0 g/100 g in the pulp) found in Brazil. The purpose of this work was the physical-chemical characterization of some nutrients and the valuation of vitamin C stability in stored camu-camu pulp, produced by the Agronomic Institute of Paraná (IAPAR), Paraná State, Brazil. The vitamin C determination was made by titration with potassium iodate. The fruit produced in Paraná State, presented a lower content of vitamin C than the one native of the amazon region, possibly due to the different development conditions of the plant, and consequently of the fruit, as well as the climatic variation, the humidity and the characteristics of the soil. Regarding the vitamin C stability in stored (-18 degrees C) camu-camu pulp, a considerable decrease in its concentration until the 28th day was observed lost 23% (from 1.57 to 1.21 g/100 g), staying approximately the same until the end of the experiment. After 335 days of storage, the content found was of approximately 1.16 g/100 g of pulp, the ascorbic acid losses amounted to 26%. This content was still higher than the one found for most fruits that are good sources of this vitamin.

Amino acid derivative-mediated detoxification and functionalization of dual cure dental restorative material for dental pulp cell mineralization.

Science.gov (United States)

Minamikawa, Hajime; Yamada, Masahiro; Iwasa, Fuminori; Ueno, Takeshi; Deyama, Yoshiaki; Suzuki, Kuniaki; Yawaka, Yasutaka; Ogawa, Takahiro

2010-10-01

Current dental restorative materials are only used to fill the defect of hard tissues, such as dentin and enamel, because of their cytotoxicity. Therefore, exposed dental pulp tissues in deep cavities must be first covered by a pulp capping material like calcium hydroxide to form a layer of mineralized tissue. However, this tissue mineralization is based on pathological reaction and triggers long-lasting inflammation, often causing clinical problems. This study tested the ability of N-acetyl cysteine (NAC), amino acid derivative, to reduce cytotoxicity and induce mineralized tissue conductivity in resin-modified glass ionomer (RMGI), a widely used dental restorative material having dual cure mechanism. Rat dental pulp cells were cultured on untreated or NAC-supplemented RMGI. NAC supplementation substantially increased the percentage of viable cells from 46.7 to 73.3% after 24-h incubation. Cell attachment, spreading, proliferative activity, and odontoblast-related gene and protein expressions increased significantly on NAC-supplemented RMGI. The mineralization capability of cells, which was nearly suppressed on untreated RMGI, was induced on NAC-supplemented RMGI. These improved behaviors and functions of dental pulp cells on NAC-supplemented RMGI were associated with a considerable reduction in the production of intracellular reactive oxygen species and with the increased level of intracellular glutathione reserves. These results demonstrated that NAC could detoxify and functionalize RMGIs via two different mechanisms involving in situ material detoxification and antioxidant cell protection. We believe that this study provides a new approach for developing dental restorative materials that enables mineralized tissue regeneration.

Effect of two fluoride varnishes on the color stability of three resin-based restorative materials: an in vitro study.

Science.gov (United States)

Tafaroji, Raha; Biria, Mina; Ameri, Farhad; Torabzadeh, Hassan; Qahari, Pasha; Akbarzadeh Baghban, Alireza

2016-11-01

The aim of the present study was to evaluate the effect of two fluoride varnishes on color stability of three resin-based restorative materials. Fifty-four discs (14.5 × 1.7 mm) were fabricated from A2 and A3 shades of a compomer (F2000), a flowable composite (Z350), and a hybrid composite (Z250), and incubated at 37°C for 48 h. Dura Shield (colored) and Fluor Protector (colorless) fluoride varnishes were applied onto the discs. The coating was cleaned using a low-speed handpiece and nylon bristle brush after 24 h of storage in distilled water. A second coating was then applied. A control group with no coating was immersed in distilled water and used. The CIE L*a*b* color scale was measured before the treatments and following each cleaning utilizing a spectrophotometer. The colored fluoride varnish exhibited the highest overall color change (∆E) after the first and the second cleaning procedures in all the materials. Among these, the greatest color change was observed in the A3 shade of F2000, followed by the A3 shade of Z-250. The ∆E was less than 3.3 in all groups, and was therefore clinically acceptable. Color changes following the application of fluoride varnishes were found to be clinically acceptable in all groups. © 2015 Wiley Publishing Asia Pty Ltd.

Color stability and staining of silorane after prolonged chemical challenges

DEFF Research Database (Denmark)

de Jesus, Vivian CBR; Martinelli, Nata Luiz; Poli-Frederico, Regina Célia

Objectives: The purpose of this study was to investigate the effect of prolonged chemical challenges on color stability and staining susceptibility of a silorane-based composite material when compared to methacrylate-based composites. Methods: Cylindrical specimens (n=24) were fabricated from...... methacrylate (Filtek Z250, 3M ESPE; Filtek Z350XT, 3M ESPE; Master Fill, Biodinâmica) or silorane-based (Filtek P90, 3M ESPE) composite materials. Initial color was registered in a spectrophotometer. Specimens were divided in four groups and individually stored at 37°C in 0.02N citric acid, 0.02N phosphoric...... acid, 75% ethanol or distilled water (control) for 7, 14, 21, and 180 days, when new measurements were performed. A staining test was performed (n=12) after 21 days of chemical challenge by immersion in coffee during 3 weeks at 37°C. Color changes (¿E) were characterized using the CIEL*a*b* color...

Microscopic analysis of dog dental pulp after pulpotomy and pulp protection with mineral trioxide aggregate and white Portland cement Análise microscópica da polpa dental de cães após pulpotomia e proteção pulpar com agregado de trióxido mineral e cimento Portland branco

Directory of Open Access Journals (Sweden)

Renato Menezes

2004-06-01

Full Text Available Considering previous studies on the similarity between the chemical composition of the mineral trioxide aggregate and the Portland cement, the purpose of this study was to investigate the pulp response of dog's teeth after pulpotomy and direct pulp protection with MTA Angelus and white Portland cement. Thirty eight pulp remnants were protected with these materials. One hundred and twenty days after treatment, the animals were sacrificed and the specimens removed and prepared for histological analysis. Both materials demonstrated the same results when used as pulp capping materials, inducing hard tissue bridge formation and maintaining pulp vitality in all specimens. The MTA Angelus and the white Portland cement showed to be effective as pulp protection materials following pulpotomy.Considerando estudos anteriores sobre a similaridade entre a composição química do agregado de trióxido mineral e o cimento Portland, o objetivo deste estudo foi investigar a resposta pulpar de dentes de cães após pulpotomia e proteção pulpar direta com MTA Angelus e cimento Portland branco. Trinta e oito remanescentes pulpares foram recobertos com esses materiais. Cento e vinte dias após o tratamento, os animais foram sacrificados e os espécimes removidos e preparados para análise histológica. Ambos os materiais demonstraram os mesmos resultados quando utilizados como materiais de capeamento pulpar, induzindo a formação de ponte de tecido mineralizado e mantendo a vitalidade pulpar em todos os espécimes. Ambos matérias se mostraram efetivos como protetores pulpares após pulpotomia em dentes de cães.

Color Stability of Enamel following Different Acid Etching and Color Exposure Times

Directory of Open Access Journals (Sweden)

Arezoo Jahanbin

2014-06-01

Full Text Available Background and aims. The aim of this study was to evaluate the effect of different etching times on enamel color stability after immediate versus delayed exposure to colored artificial saliva (CAS. Materials and methods. Human first premolars were divided into five groups of twenty. A colorimeter was used according to the CIE system on the mid-buccal and mid-lingual surfaces to evaluate initial tooth color. Samples in group A remained unetched. In groups B to E, buccal and lingual surfaces were initially etched with phosphoric acid for 15 and 60 seconds, respectively. Then, the samples in groups A and C were immersed in colored artificial saliva (cola+saliva. In group B, the teeth were immersed in simple artificial saliva (AS. Samples in groups D and E were immersed in AS for 24 and 72 hours, respectively before being immersed in colored AS. The teeth were immersed for one month in each solution before color measurement. During the test period, the teeth were retrieved from the staining solution and stored in AS for five minutes. This was repeated 60 times. Color changes of buccal and lingual surfaces were calculated. Kruskal-Wallis and Wilcoxon tests were used for statistical analysis (α ≤ 0.05. Results. There were no significant differences between the groups in term of ΔE of buccal (P = 0.148 and lingual surfaces (P = 0.73. Conclusion. Extended time of etching did not result in significant enamel color change. Immediate and delayed exposure of etched enamel to staining solutions did not result in clinically detectable tooth color changes.

Effects of cold light bleaching on the color stability of composite resins

Science.gov (United States)

Cao, Liqun; Huang, Lijuan; Wu, Meisheng; Wei, Hua; Zhao, Shouliang

2015-01-01

To evaluate the effects of cold light bleaching on the color stability of four restorations using a thermocycling stain challenge. 160 specimens (10 mm in diameter and 2 mm thick) were fabricated from 4 composite resins (Gradia Direct-A, Z350XT, Premisa, and Précis) and divided into 4 subgroups. Color was assessed according to the CIEL*a*b* color scale at baseline, after the first cycle of bleaching, after thermocycling stain challenges, and after the second cycle of bleaching. Mean values were compared using three-way analysis of variance, and multiple comparisons of the mean values were performed using the Tukey-Kramer test. All groups showed significant color changes after stain challenge, the color change was more significant in Gradia Direct and Z350XT than in Premisa and Précis. After the second cycle of bleaching, color mostly recovered to its original values. The color stability of Gradia Direct and Z350XT was inferior to that of Premisa and Précis. The discoloration of composite resin materials can be partly removed after cold light bleaching. PMID:26309549

Holdup time measurement by radioactive tracers in pulp production

International Nuclear Information System (INIS)

Roetzer, H.; Donhoffer, D.

1988-12-01

A batch of pulp was to be labelled before passing two bleaching towers of a pulp plant. Activated glass fibres were used as a tracer, which contained 24-Na with a half-life of 15 hours. It was shown in laboratory tests, that the glass fibres were suitable for transport studies of wood pulp. For use in the tests the fibres were activated and suspended in water. Due to the small diameter of the fibres (2-5 micrometers) this suspension shows physical properties very similar to the pulp. For detection six scintillation probes were mounted at different positions outside the bleaching tower. Radiation protection during the test was very easy due to the low total activity of the tracer material. Residence time distributions for both towers were measured. The successful tracer experiments show, that the method of labelling is suited for investigations of material transport in the pulp and paper industry. 3 figs., 11 refs., 2 tabs. (Author)

Evaluation of the color stability of two techniquesfor reproducing artificial irides after microwave polymerization

Directory of Open Access Journals (Sweden)

Marcelo Coelho Goiato

2011-06-01

Full Text Available The use of ocular prostheses for ophthalmic patients aims to rebuild facial aesthetics and provide an artificial substitute to the visual organ. Natural intemperate conditions promote discoloration of artificial irides and many studies have attempted to produce irides with greater chromatic paint durability using different paint materials. OBJECTIVES: The present study evaluated the color stability of artificial irides obtained with two techniques (oil painting and digital image and submitted to microwave polymerization. MATERIAL AND METHODS: Forty samples were fabricated simulating ocular prostheses. each sample was constituted by one disc of acrylic resin N1 and one disc of colorless acrylic resin with the iris interposed between the discs. The irides in brown and blue color were obtained by oil painting or digital image. The color stability was determined by a reflection spectrophotometer and measurements were taken before and after microwave polymerization. Statistical analysis of the techniques for reproducing artificial irides was performed by applying the normal data distribution test followed by 2-way ANOVA and Tukey HSD test (α=.05. RESULTS: Chromatic alterations occurred in all specimens and statistically significant differences were observed between the oil-painted samples and those obtained by digital imaging. There was no statistical difference between the brown and blue colors. Independently of technique, all samples suffered color alterations after microwave polymerization. CONCLUSION: The digital imaging technique for reproducing irides presented better color stability after microwave polymerization.

[Vital pulp therapy of damaged dental pulp].

Science.gov (United States)

Xuedong, Zhou; Dingming, Huang; Jianguo, Liu; Zhengwei, Huang; Xin, Wei; Deqin, Yang; Jin, Zhao; Liming, Chen; Lin, Zhu; Yanhong, Li; Jiyao, Li

2017-08-01

The development of an expert consensus on vital pulp therapy can provide practical guidance for the improvement of pulp damage care in China. Dental pulp disease is a major type of illness that adversely affects human oral health. Pulp capping and pulpotomy are currently the main methods for vital pulp therapy. Along with the development of minimal invasion cosmetic dentistry, using different treatment technologies and materials reasonably, preserving healthy tooth tissue, and extending tooth save time have become urgent problems that call for immediate solution in dental clinics. This paper summarizes the experiences and knowledge of endodontic experts. We develop a clinical path of vital pulp therapy for clinical work by utilizing the nature, approach, and degree of pulp damage as references, defense and self-repairing ability of pulp as guidance, and modern technologies of diagnosis and treatment as means.

Effects of polishing procedures on color stability of composite resins

Directory of Open Access Journals (Sweden)

Ahmet Umut Güler

2009-04-01

Full Text Available The purpose of this study was to investigate the effect of different polishing methods on color stability of posterior, universal and nanohybrid composite resin restorative materials upon exposure to a staining agent. Twenty-five specimens were prepared for each of 5 different composite resins (Filtek Z250, Filtek P60, Quadrant LC, Grandio and Filtek Supreme. Specimens were divided into 5 groups and different polishing procedures, including polishing discs (Pd, polishing discs then diamond polishing paste (PdP, polishing discs then a liquid polishing system (Biscover (PdB, and combinations of these (PdPB were used. Unpolished specimens served as the control (C. The specimens were stored for 48 h in a coffee solution. The color of all specimens was measured before and after exposure with a colorimeter, and total color change (DE* were calculated. The data were analyzed with a two-way ANOVA and the means were compared by Tukey HSD test (a=0.05. The lowest color difference was observed in the groups PdP and C, while the highest color difference was observed in PdPB, and PdB. When comparing the five different restorative materials, no significant difference was observed between FiltekP60 and FiltekZ250, and these materials demonstrated significantly less color change than Quadrant LC and the nanohybrid materials (Grandio, Filtek Supreme. The posterior (Filtek P60 and universal (Filtek Z250 composite resin restorative materials, which do not contain tetraethyleneglycol dimethacrylate (TEGDMA, were found to be less stainable than the nanohybrid (Grandio, Filtek Supreme and universal (Quadrant LC composite resins, which contain TEGDMA. The use of diamond polishing paste after polishing with polishing discs significantly decreased staining when compared to the groups that used polishing discs alone, for all restorative materials tested. The highest color change values were obtained for the specimens that were polished with the Biscover liquid polish

Biological evaluation of a new pulp capping material developed from Portland cement.

Science.gov (United States)

Negm, Ahmed M; Hassanien, Ehab E; Abu-Seida, Ashraf M; Nagy, Mohamed M

2017-03-02

This study evaluates the biological properties of a new pulp capping material developed from Portland cement. This study was conducted on 48 teeth in 4 dogs (12 teeth/dog). The dogs were classified into two equal groups (n=24 teeth) according to the evaluation period including: group A (3 weeks) and group B (3 months). Each group was further subdivided into three equal subgroups (n=8 teeth) according to the capping material including: subgroup 1: mineral trioxide aggregate (MTA), subgroup2: Portland cement+10% calcium hydroxide+20% bismuth oxide (Port Cal) and subgroup 3: Portland cement+bismuth oxide. After general anesthesia, a class V buccal cavity was prepared coronal to the gingival margin. After pulp exposure and hemostasis,the capping materials and glass ionomer filling were placed on the exposure sites. All histopathological findings, inflammatory cell count and dentin bridge formation were recorded. Data were analyzed statistically. After 3 months, the histopathological picture of the pulp in subgroup 1 showed normal pulp, continuous odontoblastic layer and complete dentin bridge formation while subgroup 2 showed partial and complete dentin bridge over a normal and necrotic pulps. Subgroup 3 showed loss of normal architecture, areas of necrosis, complete, or incomplete dentin bridge formation, attached and detached pulp stones and fatty degeneration in group B. For group A, MTA subgroup showed the least number of inflammatory cell infiltrate followed by Port Cal subgroup. While subgroup 3 showed the highest number of inflammatory cell infiltrate. For group B, the mean inflammatory cell count increased with the three tested materials with no statistical difference. Regarding dentin bridge formation at group A, no significant differences was found between subgroups, while at group B, MTA subgroup exhibited significantly higher scores than other subgroups. In conclusion, addition of calcium hydroxide to Portland cement improves the dentin bridge formation

Jambolan sherbets overrun, color, and acceptance in relation to the sugar, milk, and pulp contents in formulation

Directory of Open Access Journals (Sweden)

Jackeline Cintra SOARES

2018-05-01

Full Text Available Abstract The aim of this study was to evaluate in sherbet formation the effects of sugar, milk, and jambolan pulp quantity on the overrun, color, physicochemical characteristics, microbiological characteristics, and acceptance of the experimental sherbets, in addition to evaluating the bioactive compounds of the selected product. Seven formulations were established through the Simplex method. The formulation with 20g 100g-1 sugar, 45g 100g-1 milk, and 35g 100g-1 jambolan pulp was selected (S5 because it was included among the most accepted sensorially (S4 and S5, and also presented higher overrun, chroma, SST/AT, and pH than S4, receiving the scores 8.0; 8.2, 6.4 and 7.1 and 6.1, respectively, for appearance, color, flavor, texture, and odor. The selected sherbet presented a high total phenolic compound content of 192mg gallic acid g-1, and a percentage of DPPH inhibition of 73%. It is concluded that it is possible to produce jambolan sherbet with desirable physical, chemical, microbiological, and sensory characteristics, which can increase the possibilities of applying the fruit as an ingredient in the edible ice cream industry.

Effect of various teas on color stability of resin composites.

Science.gov (United States)

Dinç Ata, Gül; Gokay, Osman; Müjdeci, Arzu; Kivrak, Tugba Congara; Mokhtari Tavana, Armin

2017-12-01

To investigate the effect of various teas on color stability of resin composites. Two methacrylate-based (Arabesk Top, Grandio) and a silorane-based (Filtek Silorane) resin composites were used. 110 cylindrical samples of each resin composite were prepared (2 mm thickness and 8 mm diameter), polished and stored in distilled water (37°C for 24 hours). They were randomly divided into 11 groups (n= 10) and color measurements were taken. Then the samples were immersed in tap water (control), a black tea, a green tea or one of the eight herbal-fruit teas (37°C for 1 week) and subsequently subjected to the final color measurements. The color change of samples (ΔE*) was calculated, data were subjected to two-way ANOVA and Tukey's HSD tests. Teas, resin composites and their interactions were significant (P= 0.000). All the teas and control caused color changes in all three resin composites. Rosehip tea caused the most color changes, while tap water showed the least in all resin composites. Arabesk Top had the most staining potential in all the teas and control, whereas Filtek Silorane was the most stain resistant except Grandio immersed in sage tea. Color stability of all resin composites used were affected from both structure of resin materials and constituents of teas used. All resin composites were susceptible to staining by all teas especially rosehip tea. Arabesk Top composite showed the greatest color susceptibility in all teas and Filtek Silorane the least with one exception. Color of resin composites can be negatively affected from teas consumed. Clinicians should advise patients that drinking different kind of teas could intensify surface staining of resin based restorations.

Protective effects of seabuckthorn pulp and seed oils against radiation-induced acute intestinal injury

International Nuclear Information System (INIS)

Shi, Jing; Wang, Lan; Lu, Yan; Ji, Yue; Wang, Yaqing; Dong, Ke; Kong, Xiangqing; Sun, Wei

2017-01-01

Radiation-induced gastrointestinal syndrome, including nausea, diarrhea and dehydration, contributes to morbidity and mortality after medical or industrial radiation exposure. No safe and effective radiation countermeasure has been approved for clinical therapy. In this study, we aimed to investigate the potential protective effects of seabuckthorn pulp and seed oils against radiation-induced acute intestinal injury. C57/BL6 mice were orally administered seabuckthorn pulp oil, seed oil and control olive oil once per day for 7 days before exposure to total-body X-ray irradiation of 7.5 Gy. Terminal deoxynucleotidyl transferase dUTP nick end labeling, quantitative real-time polymerase chain reaction and western blotting were used for the measurement of apoptotic cells and proteins, inflammation factors and mitogen-activated protein (MAP) kinases. Seabuckthorn oil pretreatment increased the post-radiation survival rate and reduced the damage area of the small intestine villi. Both the pulp and seed oil treatment significantly decreased the apoptotic cell numbers and cleaved caspase 3 expression. Seabuckthorn oil downregulated the mRNA level of inflammatory factors, including tumor necrosis factor-α, interleukin (IL)-1β, IL-6 and IL-8. Both the pulp and seed oils elevated the level of phosphorylated extracellular-signal-regulated kinase and reduced the levels of phosphorylated c-Jun N-terminal kinase and p38. Palmitoleic acid (PLA) and alpha linolenic acid (ALA) are the predominant components of pulp oil and seed oil, respectively. Pretreatment with PLA and ALA increased the post-radiation survival time. In conclusion, seabuckthorn pulp and seed oils protect against mouse intestinal injury from high-dose radiation by reducing cell apoptosis and inflammation. ALA and PLA are promising natural radiation countermeasure candidates.

Glycerol Salicylate-based Pulp-Capping Material Containing Portland Cement.

Science.gov (United States)

Portella, Fernando Freitas; Collares, Fabrício Mezzomo; Santos, Paula Dapper; Sartori, Cláudia; Wegner, Everton; Leitune, Vicente Castelo Branco; Samuel, Susana Maria Werner

2015-01-01

The purpose of this study was to evaluate the water sorption, solubility, pH and ability to diffuse into dentin of a glycerol salicylate-based, pulp-capping cement in comparison to a conventional calcium hydroxide-based pulp capping material (Hydcal). An experimental cement was developed containing 60% glycerol salicylate resin, 10% methyl salicylate, 25% calcium hydroxide and 5% Portland cement. Water sorption and solubility were determined based on mass changes in the samples before and after the immersion in distilled water for 7 days. Material discs were stored in distilled water for 24 h, 7 days and 28 days, and a digital pHmeter was used to measure the pH of water. The cement's ability to diffuse into bovine dentin was assessed by Raman spectroscopy. The glycerol salicylate-based cement presented higher water sorption and lower solubility than Hydcal. The pH of water used to store the samples increased for both cements, reaching 12.59 ± 0.06 and 12.54 ± 0.05 after 7 days, for Hydcal and glycerol salicylate-based cements, respectively. Both cements were able to turn alkaline the medium at 24 h and sustain its alkalinity after 28 days. Hydcal exhibited an intense diffusion into dentin up to 40 µm deep, and the glycerol salicylate-based cement penetrated 20 µm. The experimental glycerol salicylate-based cement presents good sorption, solubility, ability to alkalize the surrounding tissues and diffusion into dentin to be used as pulp capping material.

Development and stability studies of sunscreen cream formulations containing three photo-protective filters

OpenAIRE

Smaoui, Slim; Ben Hlima, Hajer; Ben Chobba, Ines; Kadri, Adel

2013-01-01

The present study aimed to formulate and subsequently evaluate sunscreen cream (W/O/W emulsion) containing three photo-protective filters: benzophenone-3, ethylhexyl methoxycinnamate and titanium dioxide at different percentages. Formulations were stored at 8, 25 and 40 °C for four weeks to investigate their stability. Color, centrifugation, liquefaction, phase separation, pH and Sun Protection Factor (SPF) of sunscreen cream formulations were determined. The microbiological stability of the ...

Multifunctional AgNPs@Wool: colored, UV-protective and antioxidant functional textiles

Science.gov (United States)

Shabbir, Mohd; Mohammad, Faqeer

2018-02-01

Nanomaterials have great impact on textile industry for multifunctional and smart clothing as per the need of present, and further, green nanotechnology is the current hotspot of research and industrial developments. Silver nanoparticles (AgNPs) are synthesized (in situ) by using natural compounds of plant extracts (naphthoquinones, phenolics/flavonoids, polyphenols) as reducing or stabilizing agents, and simultaneously deposited on wool fabric for coloration, UV protection and antioxidant properties. UV-visible spectroscopy is used to monitor the route of biosynthesis of nanoparticles and transmission electron microscopy for morphological characteristics of synthesized AgNPs. Spherical and almost oval-shaped AgNPs were synthesized by naphthoquinones, polyphenols and flavonoids, respectively. Scanning electron microscopy (SEM) coupled with energy dispersive X-ray (EDX) spectroscopy, X-ray diffraction pattern (XRD) and Fourier transform infrared spectroscopy were used for the AgNPs@Wool fabrics characterization. SEM-EDX analysis and XRD patterns confirmed the successful deposition of silver nanoparticles on wool. Coloration characteristics in terms of color strength (K/S) and CIEL*a*b*c*h° values, UV protection abilities in terms of UV transmittance and UV protection factor, and % antioxidant activity of AgNPs@Wool are suggestive of good-to-excellent results.

Efficacy of polishing kits on the surface roughness and color stability ...

African Journals Online (AJOL)

Objective: Different polishing kits may have different effects on the composite resin surfaces. The aim of this study was to evaluate the surface roughness and color stability of four different composites which was applied different polishing technique. Materials and Methods: Thirty specimens were made for each composite ...

Characterisation of Arabica Coffee Pulp - Hay from Kintamani - Bali as Prospective Biogas Feedstocks

Directory of Open Access Journals (Sweden)

Hendroko Setyobudi Roy

2018-01-01

Full Text Available The huge amount of coffee pulp waste is an environmental problem. Anaerobic fermentation is one of the alternative solutions. However, availability of coffee pulp does not appear for year-round, whereas biogas needs continuous feedstocks for digester stability. This research uses coffee pulp from Arabica Coffee Factory at Mengani, Kintamani, Bali–Indonesia. The coffee pulp was transformed into coffee pulp-hay product by sun drying for preservations to extend the raw materials through the year. Characterization of coffee pulp-hay was conducted after to keep for 15 mo for review the prospect as biogas feedstocks. Several parameters were analyzed such as C/N ratio, volatile solids, carbohydrate, protein, fat, lignocellulose content, macro-micro nutrients, and density. The review results indicated that coffee pulp-hay is prospective raw material for biogas feedstock. This well-proven preservation technology was able to fulfill the continuous supply. Furthermore, some problems were found in the recent preliminary experiment related to the density and fungi growth in the conventional laboratory digester. Further investigation was needed to implement the coffee pulp – hay as biogas feedstocks.

Color stability of CAD/CAM Zirconia ceramics following exposure to acidic and staining drinks.

Science.gov (United States)

Colombo, Marco; Cavallo, Marco; Miegge, Matteo; Dagna, Alberto; Beltrami, Riccardo; Chiesa, Marco; Poggio, Claudio

2017-11-01

The aim of this in vitro study was to evaluate the color stability of CAD/CAM Zirconia ceramics following exposure to acidic drink (Coca Cola) and after exposure to staining solution (coffee). All the samples were immersed in different staining solutions over a 28-day test period. A colorimetric evaluation according to the CIE L*a*b* system was performed by a blind trained operator at 7, 14, 21, 28 days of the staining process. Shapiro Wilk test and Kruskal-Wallis ANOVA were applied to assess significant differences among restorative materials. Paired t-test was applied to test which CIE L*a*b* parameters significantly changed after immersion in staining solutions. One week immersion in acidic drink did not cause a perceivable discoloration for all restorative materials (ΔE < 3.3). Subsequent immersion in coffee affected color stability of all Zirconia samples, even if Kruskal-Wallis ANOVA found significant differences among the various restorative materials. The ∆Es of CAD/CAM Zirconia ceramics after immersion in coffee varied among the products, but color integrity is not affected by contact with acidic drinks. Key words: CAD/CAM restorative materials, CIE Lab, Zirconia ceramics.

Color stability of CAD/CAM Zirconia ceramics following exposure to acidic and staining drinks

Science.gov (United States)

Colombo, Marco; Cavallo, Marco; Miegge, Matteo; Dagna, Alberto; Beltrami, Riccardo; Chiesa, Marco

2017-01-01

Background The aim of this in vitro study was to evaluate the color stability of CAD/CAM Zirconia ceramics following exposure to acidic drink (Coca Cola) and after exposure to staining solution (coffee). Material and Methods All the samples were immersed in different staining solutions over a 28-day test period. A colorimetric evaluation according to the CIE L*a*b* system was performed by a blind trained operator at 7, 14, 21, 28 days of the staining process. Shapiro Wilk test and Kruskal-Wallis ANOVA were applied to assess significant differences among restorative materials. Paired t-test was applied to test which CIE L*a*b* parameters significantly changed after immersion in staining solutions. Results One week immersion in acidic drink did not cause a perceivable discoloration for all restorative materials (ΔE < 3.3). Subsequent immersion in coffee affected color stability of all Zirconia samples, even if Kruskal-Wallis ANOVA found significant differences among the various restorative materials. Conclusions The ∆Es of CAD/CAM Zirconia ceramics after immersion in coffee varied among the products, but color integrity is not affected by contact with acidic drinks. Key words:CAD/CAM restorative materials, CIE Lab, Zirconia ceramics. PMID:29302281

Durability of pulp fiber-cement composites

Science.gov (United States)

Mohr, Benjamin J.

Wood pulp fibers are a unique reinforcing material as they are non-hazardous, renewable, and readily available at relatively low cost compared to other commercially available fibers. Today, pulp fiber-cement composites can be found in products such as extruded non-pressure pipes and non-structural building materials, mainly thin-sheet products. Although natural fibers have been used historically to reinforce various building materials, little scientific effort has been devoted to the examination of natural fibers to reinforce engineering materials until recently. The need for this type of fundamental research has been emphasized by widespread awareness of moisture-related failures of some engineered materials; these failures have led to the filing of national- and state-level class action lawsuits against several manufacturers. Thus, if pulp fiber-cement composites are to be used for exterior structural applications, the effects of cyclical wet/dry (rain/heat) exposure on performance must be known. Pulp fiber-cement composites have been tested in flexure to examine the progression of strength and toughness degradation. Based on scanning electron microscopy (SEM), environmental scanning electron microscopy (ESEM), energy dispersive spectroscopy (EDS), a three-part model describing the mechanisms of progressive degradation has been proposed: (1) initial fiber-cement/fiber interlayer debonding, (2) reprecipitation of crystalline and amorphous ettringite within the void space at the former fiber-cement interface, and (3) fiber embrittlement due to reprecipitation of calcium hydroxide filling the spaces within the fiber cell wall structure. Finally, as a means to mitigate kraft pulp fiber-cement composite degradation, the effects of partial portland cement replacement with various supplementary cementitious materials (SCMs) has been investigated for their effect on mitigating kraft pulp fiber-cement composite mechanical property degradation (i.e., strength and toughness

Color profiles and stability of acylated and nonacylated anthocyanins as novel pigment sources in a lipstick model: A viable alternative to synthetic colorants.

Science.gov (United States)

Westfall, Alexandra; Giusti, Mónica

Cosmetics, such as lipstick, can affect an individual's perception of attractiveness and morale. Consumer concern with the safety of synthetic colorants has made the need for alternative natural color sources increasingly urgent. Our goal was to evaluate the feasibility of anthocyanin (ACN) extracts as colorants in lipstick formulations. Lipstick formulations were colored with ACN-rich materials. Accelerated environmental testing typical of the cosmetic industry were used: incubation at 20°, 37°, and 45°C for 12 weeks and temperature abuse cycles between 20°/37°C or -20°/20°C. Color (CIELab) and total monomeric ACN (pH-differential) changes were monitored to determine shelf stability of the product. All formulations exhibited acceptable color for lipsticks. Shelf stability was determined to exceed 2 year based on the accelerated testing conditions. Formulations containing cyanidin as their main ACN were the most stable (elderberry, purple corn, and purple sweet potato). ACNs could be used as suitable alternatives to synthetic colorants in lipid-based topical formulations.

Biological response of pulps submitted to different capping materials Resposta biológica de polpas submetidas a diferentes materiais capeadores

Directory of Open Access Journals (Sweden)

André Luiz Fraga Briso

2006-09-01

Full Text Available Pulp capping is a procedure that comprises adequate protection of the pulp tissue exposed to the oral environment, aiming at the preservation of its vitality and functions. This study evaluated the response of the dental pulps of dog teeth to capping with mineral trioxide aggregate (MTA or calcium hydroxide P.A. For that purpose, 37 teeth were divided into two groups, according to the capping material employed. Two dogs were anesthetized and, after placement of a rubber dam, their pulps were exposed in a standardized manner and protected with the experimental capping materials. The cavities were then sealed with resin-modified glass ionomer cement and restored with composite resin. After sixty days, the animals were killed and the specimens were processed in order to be analyzed with optic microscopy. It was observed that MTA presented a higher success rate compared to calcium hydroxide, presenting a lower occurrence of infection and pulp necrosis.O capeamento pulpar é um procedimento que consiste na adequada proteção do tecido pulpar exposto ao meio oral, objetivando a preservação de sua vitalidade e suas funções. O objetivo deste trabalho foi observar a resposta da polpa dental de cães ao capeamento com o agregado de trióxido mineral (MTA ou hidróxido de cálcio P.A. Para tanto, 37 dentes foram divididos em dois grupos, de acordo com o material capeador utilizado. Dois cães foram anestesiados e após o isolamento absoluto do campo operatório, realizou-se exposição padronizada da polpa, proteção com os materiais capeadores testados e selamento das cavidades com cimento modificado de ionômero de vidro. Os dentes foram então restaurados com resina composta. Após sessenta dias, os animais foram sacrificados e as peças foram processadas para a análise microscópica dos dentes. Observou-se que o MTA apresentou maior índice de sucesso em relação ao hidróxido de cálcio, evidenciando menor ocorrência de infecção e necrose

Effect of protective atmosphere on color of goose meat.

Science.gov (United States)

Orkusz, A; Woloszyn, J; Haraf, G; Okruszek, A

2013-08-01

The objective of the work was to characterize the color of the of the goose breast meat packaged in protective atmosphere and stored in the refrigerated conditions. The aim was realized by determination of total heme pigment concentration; relative concentration of myoglobin, oxymyoglobin, and metmyoglobin; parameters of color L* (lightness), a* (redness), and b* (yellowness); and sensory evaluation of the surface color. The experimental material was White Kołuda goose boneless breast meat with the skin from industrial slaughter. The following 2 protective atmospheres were used in the study: vacuum and modified atmosphere (MA) consisting of 80% O2 and 20% CO2. The muscles packed in protective atmosphere were examined on d 4, 7, 11, and 14 of storage. A control sample was goose breast meat stored in air and tested after 24 h after slaughter. The total pigment concentration decreased gradually within 14 d of storage for samples packed in 2 types of atmospheres. The increase in relative concentration of metmyoglobin and the decrease in oxymyoglobin relative concentration in total heme pigments in the meat stored in MA was noticed. However, in all times of storage, the relative concentration of the 3 samples of myoglobin forms stored in vacuum was unchanged. The color parameters (L*, a*, b*) did not change for 14 d of storage in the muscles packed in vacuum. One can state a decrease of the value of the color parameter a* as well as an increase of the value of the color parameter b* in the samples packed in MA. From d 11 to 14 of storage, goose meat packed under MA had lower sensory evaluation intensity of color than muscles under vacuum. The obtained data indicated that the surface color of goose breast meat packed in MA (consisting of 80% O2, 20% CO2) or vacuum packed was maintained for 11 and 14 d, respectively.

Pemanfaatan Limbah Pulp Buah Semangka (Citrullus vulgaris, Schard) Untuk Pembuatan Nata De Watermelon Pulp Dengan Menggunakan Bakteri Acetobacter xylinum

OpenAIRE

Mawaddah

2011-01-01

This research done to know can or not the waste of watermelon pulp use to produce nata and how the effect of mass variation using to nata’s quality. This research was done with mass variation of watermelon pulp that is 10 g, 20 g, 30 g, 40 g, 50 g, 60 g, and watermelon pulp without adding sugar as control. Statistical analysis count the thickness, water content, ash content, fiber content and organoleptic test of texture, color, aroma, and taste of nata de watermelon pulp. The result show...

Optimization of pulping conditions of abaca. An alternative raw material for producing cellulose pulp.

Science.gov (United States)

Jiménez, L; Ramos, E; Rodríguez, A; De la Torre, M J; Ferrer, J L

2005-06-01

The influence of temperature (150-170 degrees C), pulping time (15-45 min) and soda concentration (5-10%) in the pulping of abaca on the yield, kappa, viscosity, breaking length, stretch and tear index of pulp and paper sheets, was studied. Using a factorial design to identify the optimum operating conditions, equations relating the dependent variables to the operational variables of the pulping process were derived that reproduced the former with errors lower than 25%. Using a high temperature, and a medium time and soda concentration, led to pulp that was difficult to bleach (kappa 28.34) but provided acceptable strength-related properties (breaking length 4728 m; stretch 4.76%; tear index 18.25 mN m2/g), with good yield (77.33%) and potential savings on capital equipment costs. Obtaining pulp amenable to bleaching would entail using more drastic conditions than those employed in this work.

2013 Early Career Achievement Award--Proteomics of muscle- and species-specificity in meat color stability.

Science.gov (United States)

Suman, S P; Rentfrow, G; Nair, M N; Joseph, P

2014-03-01

Meat color is the most important quality trait influencing consumer purchase decisions. The interinfluential interactions between myoglobin and biomolecules govern color stability in meat. The advances in proteomics, such as high throughput analytical tools in mass spectrometry, 2-dimensional electrophoresis, and bioinformatics, offer themselves as robust techniques to characterize the proteome basis of muscle- and species-specific meat color phenomena. Differential abundance of chaperones and antioxidant proteins contributes to muscle-specific color stability in beef; the greater abundance of chaperones and antioxidant proteins in color-stable Longissimus lumborum than in color-labile Psoas major protects myoglobin and contributes to superior color stability of beef Longissimus steaks. Lipid oxidation-induced myoglobin oxidation is more critical to beef color than pork color due to the inherent differences in myoglobin chemistry; the number of nucleophilic histidine residues adducted by reactive aldehydes is greater in beef myoglobin than in pork myoglobin. Preferential adduction of secondary products of lipid oxidation to beef myoglobin accelerates metmyoglobin formation at a greater degree than in its pork counterpart. Mass spectrometric investigations revealed that although cherry-red carboxymyoglobin is more stable than oxymyoglobin, both redox forms undergo lipid oxidation-induced oxidation in model systems. The accuracy of mass spectrometry to detect the molecular mass of proteins has been applied to differentiate myoglobins from closely related meat animals, such as goats and sheep or emu and ostrich. In addition, this approach indicated that turkey myoglobin is 350 Da greater in molecular mass than beef myoglobin, and the unique biochemistry of turkey myoglobin could be responsible for its greater thermostability in model systems as well as the pink color defect observed in fully cooked uncured turkey products.

Comparative profiling of sarcoplasmic phosphoproteins in ovine muscle with different color stability.

Science.gov (United States)

Li, Meng; Li, Zheng; Li, Xin; Xin, Jianzeng; Wang, Ying; Li, Guixia; Wu, Liguo; Shen, Qingwu W; Zhang, Dequan

2018-02-01

The phosphorylation of sarcoplasmic proteins in postmortem muscles was investigated in relationship to color stability in the present study. Although no difference was observed in the global phosphorylation level of sarcoplasmic proteins, difference was determined in the phosphorylation levels of individual protein bands from muscles with different color stability. Correlation analysis and liquid chromatography - tandem mass spectrometry (LC-MS/MS) identification of phosphoproteins showed that most of the color stability-related proteins were glycolytic enzymes. Interestingly, the phosphorylation level of myoglobin was inversely related to meat color stability. As the phosphorylation of myoglobin increased, color stability based on a ∗ value decreased and metMb content increased. In summary, the study revealed that protein phosphorylation might play a role in the regulation of meat color stability probably by regulating glycolysis and the redox stability of myoglobin, which might be affected by the phosphorylation of myoglobin. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Experimental Study of the Performance of Nano-Thin Polyelectrolyte Shell for Dental Pulp Stem Cells Immobilization.

Science.gov (United States)

Grzeczkowicz, A; Granicka, L H; Maciejewska, I; Strawski, M; Szklarczyk, M; Borkowska, M

2015-12-01

Carious is the most frequent disease of mineralized dental tissues which might result in dental pulp inflammation and mortality. In such cases an endodontic treatment is the only option to prolong tooth functioning in the oral cavity; however, in the cases of severe pulpitis, especially when complicated with periodontal tissue inflammation, the endodontic treatment might not be enough to protect against tooth loss. Thus, keeping the dental pulp viable and/or possibility of the reconstruction of a viable dental pulp complex, appears to become a critical factor for carious and/or pulp inflammation treatment. The nowadays technologies, which allow handling dental pulp stem cells (DPSC), seem to bring us closer to the usage of dental stem cells for tooth tissues reconstruction. Thus, DPSC immobilized within nano-thin polymeric shells, allowing for a diffusion of produced factors and separation from bacteria, may be considered as a cover system supporting technology of dental pulp reconstruction. The DPSC were immobilized using a layer-by-layer technique within nano-thin polymeric shells constructed and modified by nanostructure involvement to ensure the layers stability and integrity as well as separation from bacterial cells. The cytotoxity of the material used for membrane production was assessed on the model of adherent cells. The performance of DPSC nano-coating was assessed in vitro. Membrane coatings showed no cytotoxicity on the immobilized cells. The presence of coating shell was confirmed with flow cytometry, atomic force microscopy and visualized with fluorescent microscopy. The transfer of immobilized DPSC within the membrane system ensuring cells integrity, viability and protection from bacteria should be considered as an alternative method for dental tissues transportation and regeneration.

Cellulosic pulps of cereal straws as raw material for the manufacture of ecological packaging

OpenAIRE

Vargas González, Fátima; González, Zoilo; Sánchez, Rafael; Jiménez, Luis; Rodríguez Pascual, Alejandro

2012-01-01

The aim of this work was to study the potential application of four types of cereal straws: oats, maize, rapeseed, and barley, in order to obtain cellulose pulp through the Specel® process for use in the manufacture of 100% biodegradable and ecological packaging. Raw materials were chemically characterized to determine alcohol-extractives, ash, lignin, holocellulose, and α-cellulose. Cellulosic pulps obtained from raw materials were characterized to determine yield, Kappa number, and viscosit...

Static Magnetic Field Attenuates Lipopolysaccharide-Induced Inflammation in Pulp Cells by Affecting Cell Membrane Stability

Directory of Open Access Journals (Sweden)

Sung-Chih Hsieh

2015-01-01

Full Text Available One of the causes of dental pulpitis is lipopolysaccharide- (LPS- induced inflammatory response. Following pulp tissue inflammation, odontoblasts, dental pulp cells (DPCs, and dental pulp stem cells (DPSCs will activate and repair damaged tissue to maintain homeostasis. However, when LPS infection is too serious, dental repair is impossible and disease may progress to irreversible pulpitis. Therefore, the aim of this study was to examine whether static magnetic field (SMF can attenuate inflammatory response of dental pulp cells challenged with LPS. In methodology, dental pulp cells were isolated from extracted teeth. The population of DPSCs in the cultured DPCs was identified by phenotypes and multilineage differentiation. The effects of 0.4 T SMF on DPCs were observed through MTT assay and fluorescent anisotropy assay. Our results showed that the SMF exposure had no effect on surface markers or multilineage differentiation capability. However, SMF exposure increases cell viability by 15%. In addition, SMF increased cell membrane rigidity which is directly related to higher fluorescent anisotropy. In the LPS-challenged condition, DPCs treated with SMF demonstrated a higher tolerance to LPS-induced inflammatory response when compared to untreated controls. According to these results, we suggest that 0.4 T SMF attenuates LPS-induced inflammatory response to DPCs by changing cell membrane stability.

Morphological Study Of Border Area Of Pulp-Capping Materials And Er:YAG Laser Prepared Hard Dental Surface

Directory of Open Access Journals (Sweden)

Stefanova Vessela P.

2015-03-01

Full Text Available Introduction: Vital pulp therapy involves biologically based therapeutic activities aimed at restoring health and preserving the vitality of cariously or traumatically damaged pulp. Adaptation of pulp-capping materials to the prepared tooth surface may be the key to the success of biological tooth treatment.

Kinetics of pulp mill effluent treatment by ozone-based processes

International Nuclear Information System (INIS)

Ko, Chun-Han; Hsieh, Po-Hung; Chang, Meng-Wen; Chern, Jia-Ming; Chiang, Shih-Min; Tzeng, Chewn-Jeng

2009-01-01

The wastewaters generated from wood pulping and paper production processes are traditionally treated by biological and physicochemical processes. In order to reduce chemical oxygen demand (COD) and color to meet increasingly strict discharge standards, advanced oxidation processes (AOPs) are being adapted as polishing treatment units. Various ozone-based processes were used in this study to treat simulated wastewaters prepared from black liquor from a hardwood Kraft pulp mill in Taiwan. The experimental results showed that the COD and color were primarily removed by direct ozone oxidation and activated carbon adsorption. While the addition of activated carbon could enhance the COD and color removal during ozonation, the addition of hydrogen peroxide improved the color removal only. For the various ozone-based treatment processes, kinetic models were developed to satisfactorily predict the COD and color removal rates. According to the kinetic parameters obtained from the various ozone-based processes, the enhanced COD and color removal of ozonation in the presence of activated carbon was attributed to the regeneration of the activated carbon by ozonation. These kinetic models can be used for reactor design and process design to treat pulping wastewater using ozone-based processes.

Effect of gamma irradiation combined with hot water treatment on the texture, pulp color and sensory quality of ''Nahng Glahng Wahn'' mangoes

International Nuclear Information System (INIS)

Lacroix, M.; Jobin, M.; Beliveau, M.; Gagnon, M.

1992-01-01

Mangoes (Mangifera indica L.) from Thailand of the 'Nahng Glahng Wahn' variety were irradiated with a 60 Co source at a dose of 0.63 kGy and a dose rate of 9.23 kGy/hr, with or without a hot water treatment prior to irradiation. The irradiation treatment had little effect on the texture and preserved the yellow color in the pulp. Test of sensory evaluation revealed that irradiated mango pulp was preferred for overall appearance, taste, texture and palatability. The appearance of whole irradiated mangoes was also preferred over that of the control mangoes. However, no significant differences were observed between irradiated and hot water dipped irradiated mangoes for all characteristics studied in mangoes pulp. The results showed that these treatments (hot water dip plus irradiation or irradiation alone) are useful and non-destructive methods to preserve consumer acceptability

Effect of Salivary pH on Color Stability of Different Flowable Composites - A Prospective In-vitro Study.

Science.gov (United States)

Batra, Renu; Kataria, Pratik; Kapoor, Sonali

2016-10-01

Scientifically and clinically there has been lot of development in the field of aesthetic dentistry. However, there is limited or restricted information regarding the color stability of flowable composite materials. The aim of this study was to evaluate the spectrophotometric color stability of three different flowable composite materials with respect to three different pH of saliva. The study included 90 different samples. Thirty samples in each composite group; (Group A: G-aenial universal flo; Group B: Z 350 XT flowable; Group C: Esthet x flow). All samples from each group were immersed in distilled water for 24 hours. Total color difference (ΔE) was recorded for each sample. After this 10 samples from each group were respectively immersed in 6.5, 7 and 7.5 pH of artificial saliva. All samples were kept in dark room for seven days and then ΔE for each sample was recorded and was compared to previous recorded ΔE for the same sample. Maximum color change was seen irrespective of material in 6.5 pH of saliva. G-aenial universal flo showed least change irrespective of pH of saliva. Thus, the present study reveals that acidic pH level affects the coloration of composite resins by affecting the surface integrity and as reported in previous studies, various coloring agents in beverages and other dietary components assists the process due to absorption of these coloring substances into the resin matrix.

Materials used for indirect pulp treatment in primary teeth: a mixed treatment comparisons meta-analysis

Directory of Open Access Journals (Sweden)

Pablo Silveira dos Santos

2017-12-01

Full Text Available Abstract: This study aimed to systematically review the literature to address the question regarding the influence of different materials in the clinical and radiographic success of indirect pulp treatment in primary teeth. A literature search was carried out for articles published prior to January 2017 in PubMed/MEDLINE, CENTRAL, Scopus, TRIP and ClinicalTrials databases; relevant articles included randomized clinical trials that compared materials used for indirect pulp treatment in primary teeth. Two reviewers independently selected the studies and extracted the data. The effects of each material on the outcome (clinical and radiographic failures were analyzed using a mixed treatment comparisons meta-analysis. The ranking of treatments according to their probability of being the best choice was also calculated. From 1,088 potentially eligible studies, 11 were selected for full-text analysis, and 4 were included in the meta-analysis. In all papers, calcium hydroxide liner was used as the control group versus an adhesive system, resin-modified glass ionomer cement or placebo. The follow-up period ranged from 24 to 48 months, with dropout rates of 0-25.7%. The material type did not significantly affect the risk of failure of the indirect pulp treatment. However, calcium hydroxide presented a higher probability of failure. In conclusion, there is no scientific evidence showing the superiority of any material used for indirect pulp treatment in primary teeth.

High isostatic pressure and thermal processing of açaí fruit (Euterpe oleracea Martius): Effect on pulp color and inactivation of peroxidase and polyphenol oxidase.

Science.gov (United States)

Jesus, Ana Laura Tibério de; Leite, Thiago Soares; Cristianini, Marcelo

2018-03-01

The present study evaluated the effect of high isostatic pressure (HIP) on the activity of peroxidase (POD) and polyphenol oxidase (PPO) from açaí. Açaí pulp was submitted to several combinations of pressure (400, 500, 600MPa), temperature (25 and 65°C) for 5 and 15min. The combined effect of HIP technology and high temperatures (690MPa by 2 and 5min at 80°C) was also investigated and compared to the conventional thermal treatment (85°C/1min). POD and PPO enzyme activity and instrumental color were examined after processing and after 24h of refrigerated storage. Results showed stability of POD for all pressures at 25°C, which proved to be heat-resistant and baro-resistant at 65°C. For PPO, the inactivation at 65°C was 71.7% for 600MPa after 15min. In general, the increase in temperature from 25°C to 65°C reduced the PPO relative activity with no changes in color. Although the thermal treatment and the HIP (690MPa) along with high temperature (80°C) reduced the PPO relative activity, and relevant darkening was observed in the processed samples. Thus, it can be concluded that POD is more baro-resistant than PPO in açaí pulp subjected to the same HIP processing conditions and processing at 600MPa/65°C for 5min may be an effective alternative for thermal pasteurization treatments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects of protein phosphorylation on color stability of ground meat.

Science.gov (United States)

Li, Meng; Li, Xin; Xin, Jianzeng; Li, Zheng; Li, Guixia; Zhang, Yan; Du, Manting; Shen, Qingwu W; Zhang, Dequan

2017-03-15

The influence of protein phosphorylation on meat color stability was investigated in this study. Phosphatase and protein kinase inhibitors were added to minced ovine Longissimus thoracis et lumborum (LTL) muscle to manipulate the global phosphorylation of sarcoplasmic proteins. The data obtained show that the rate and extent of pH decline, along with lactate accumulation in postmortem muscle, were related to protein phosphorylation. Analysis of meat color and the relative content of myoglobin redox forms revealed that meat color stability was inversely related to the phosphorylation of sarcoplasmic proteins. Thus, this study suggests that protein phosphorylation may be involved in meat color development by regulating glycolysis and the redox stability of myoglobin. Copyright © 2016 Elsevier Ltd. All rights reserved.

Improvement in rice straw pulp bleaching effluent quality by incorporating oxygen delignification stage prior to elemental chlorine-free bleaching.

Science.gov (United States)

Kaur, Daljeet; Bhardwaj, Nishi K; Lohchab, Rajesh Kumar

2017-10-01

Environmental degradation by industrial and other developmental activities is alarming for imperative environmental management by process advancements of production. Pulp and paper mills are now focusing on using nonwood-based raw materials to protect forest resources. In present study, rice straw was utilized for pulp production as it is easily and abundantly available as well as rich in carbohydrates (cellulose and hemicelluloses). Soda-anthraquinone method was used for pulp production as it is widely accepted for agro residues. Bleaching process during paper production is the chief source of wastewater generation. The chlorophenolic compounds generated during bleaching are highly toxic, mutagenic, and bioaccumulative in nature. The objectives of study were to use oxygen delignification (ODL) stage prior to elemental chlorine-free (ECF) bleaching to reduce wastewater load and to study its impact on bleached pulp characteristics. ODL stage prior to ECF bleaching improved the optical properties of pulp in comparison to only ECF bleaching. When ODL stage was incorporated prior to bleaching, the tensile index and folding endurance of the pulp were found to be 56.6 ± 1.5 Nm/g and 140, respectively, very high in comparison to ECF alone. A potential reduction of 51, 57, 43, and 53% in BOD 3 , COD, color, and AOX, respectively was observed on adding the ODL stage compared to ECF only. Generation of chlorophenolic compounds was reduced significantly. Incorporation of ODL stage prior to bleaching was found to be highly promising for reducing the toxicity of bleaching effluents and may lead to better management of nearby water resources. Graphical abstract ᅟ.

Color Stability of CAD/CAM Fabricated Inlays after Accelerated Artificial Aging.

Science.gov (United States)

Karaokutan, Isil; Yilmaz Savas, Tuba; Aykent, Filiz; Ozdere, Eda

2016-08-01

To investigate the influence of accelerated artificial aging on the color stability of three different inlay restorations produced with a CAD/CAM system. Thirty non-carious human mandibular molar teeth were used. The teeth were embedded in autopolymerizing acrylic resin blocks. Standard Class I inlay cavities were prepared, and the teeth were randomly divided into three groups (n = 10) to fabricate inlay restorations: (1) a feldspathic-ceramic group, (2) a resin nano-ceramic group, and (3) a leucite glass-ceramic group. Optical impressions were made with CEREC software, and the restorations were designed and then milled. The inlays were adhesively cemented with a dual-polymerizing resin cement and left in distilled water at room temperature for 1 week. Color measurements were performed with a spectrophotometer before and after accelerated aging in a weathering machine with a total energy of 150 kJ/m(2) . Changes in color (∆E, ∆L, ∆a, ∆b, ∆C) were determined using the CIE L*a*b* system. The results were assessed using a one-way ANOVA and Tukey's HSD test (p = 0.05). The color changes of the materials ranged from 2.1 to 9.29. The highest color change was seen in the resin nano-ceramic material. This change was not clinically acceptable (∆E > 5.5). No significant differences were found in the ∆L and ∆a values of the test groups. Color changes were observed in each evaluated material after accelerated aging. All CAD/CAM inlays became darker in appearance, more saturated, a little reddish, and more yellow. © 2015 by the American College of Prosthodontists.

Effect of time and storage conditions on the physical and physico-chemical characteristics of the pulp of yellow and purple passion fruit

Directory of Open Access Journals (Sweden)

Letícia da Silva ARAÚJO

Full Text Available Abstract The aim of this study was evaluate the physical and physico-chemical characteristics of extracted fruit pulp of passion fruit with different skin color (yellow, light and dark purple under refrigeration temperatures and storage times. The extracted pulp of passion fruit was stored at different temperatures: 10 °C, 25 °C; - 30 °C and - 80 °C and at four different storage periods: 0; 10; 20 and 30 days. The following physical and physico-chemical characteristics of the fruit were evaluated: color of fruit peel, fruit weight, diameter, length and width of the fruit, peel thickness, peel mass, pulp mass, pulp color, juice yield, pH, soluble solids, titratable acidity and ratio. The physical and physico-chemical results indicate that all the passion fruit pulp, in natura as well as refrigerated, presented values in conformity to the identity and quality standards. The coloration of the fruit peel influenced the preservation of pulp color during the storage period and conditions. Purple fruits showed no change in the color of the pulp, even under different conservation procedures. The passion fruit pulp can be stored up to 30 days while preserving the physical and physico-chemical characteristics, similar to the pulp in natura.

Synthetic Light-Curable Polymeric Materials Provide a Supportive Niche for Dental Pulp Stem Cells.

Science.gov (United States)

Vining, Kyle H; Scherba, Jacob C; Bever, Alaina M; Alexander, Morgan R; Celiz, Adam D; Mooney, David J

2018-01-01

Dental disease annually affects billions of patients, and while regenerative dentistry aims to heal dental tissue after injury, existing polymeric restorative materials, or fillings, do not directly participate in the healing process in a bioinstructive manner. There is a need for restorative materials that can support native functions of dental pulp stem cells (DPSCs), which are capable of regenerating dentin. A polymer microarray formed from commercially available monomers to rapidly identify materials that support DPSC adhesion is used. Based on these findings, thiol-ene chemistry is employed to achieve rapid light-curing and minimize residual monomer of the lead materials. Several triacrylate bulk polymers support DPSC adhesion, proliferation, and differentiation in vitro, and exhibit stiffness and tensile strength similar to existing dental materials. Conversely, materials composed of a trimethacrylate monomer or bisphenol A glycidyl methacrylate, which is a monomer standard in dental materials, do not support stem cell adhesion and negatively impact matrix and signaling pathways. Furthermore, thiol-ene polymerized triacrylates are used as permanent filling materials at the dentin-pulp interface in direct contact with irreversibly injured pulp tissue. These novel triacrylate-based biomaterials have potential to enable novel regenerative dental therapies in the clinic by both restoring teeth and providing a supportive niche for DPSCs. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Evaluation of a value prior to pulping-thermomechanical pulp business concept. Part 2.

Science.gov (United States)

Ted Bilek; Carl Houtman; Peter Ince

2011-01-01

Value Prior to Pulping (VPP) is a novel biorefining concept for pulp mills that includes hydrolysis extraction of hemicellulose wood sugars and acetic acid from pulpwood prior to pulping. The concept involves conversion of wood sugars via fermentation to fuel ethanol or other chemicals and the use of remaining solid wood material in the pulping process. This paper...

Stability of color in Spanish-style green table olives pasteurized and stored in plastic containers.

Science.gov (United States)

Sánchez, Antonio Higinio; López-López, Antonio; Beato, Víctor Manuel; de Castro, Antonio; Montaño, Alfredo

2017-08-01

There is an increasing interest in the use of pasteurizable plastic packaging by the olive industry. In order to investigate the change from traditional glass or varnished can containers to plastic packaging, the proper plastic material that is compatible with fermented olives while maintaining color quality during pasteurization treatment and storage must be selected. This work is focused on color stability in two distinct pasteurizable plastic containers with different oxygen permeability. In PET + MDPE/EVOH (polyethylene terephthalate + medium-density polyethylene/ethylene vinyl alcohol) pouches, pasteurization provoked severe browning which drastically decreased their color shelf life ( 6.5 months). The plastic material had a significant effect on the retention of color of the pasteurized product. The use of AlOx-coated PET + MDPE pouches could be an alternative to traditional packaging for the pasteurization and storage of Spanish-style green olives from a color quality standpoint. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Prediction of textural attributes using color values of banana (Musa sapientum) during ripening.

Science.gov (United States)

Jaiswal, Pranita; Jha, Shyam Narayan; Kaur, Poonam Preet; Bhardwaj, Rishi; Singh, Ashish Kumar; Wadhawan, Vishakha

2014-06-01

Banana is an important sub-tropical fruit in international trade. It undergoes significant textural and color transformations during ripening process, which in turn influence the eating quality of the fruit. In present study, color ('L', 'a' and 'b' value) and textural attributes of bananas (peel, fruit and pulp firmness; pulp toughness; stickiness) were studied simultaneously using Hunter Color Lab and Texture Analyser, respectively, during ripening period of 10 days at ambient atmosphere. There was significant effect of ripening period on all the considered textural characteristics and color properties of bananas except color value 'b'. In general, textural descriptors (peel, fruit and pulp firmness; and pulp toughness) decreased during ripening except stickiness, while color values viz 'a' and 'b' increased with ripening barring 'L' value. Among various textural attributes, peel toughness and pulp firmness showed highest correlation (r) with 'a' value of banana peel. In order to predict textural properties using color values of banana, five types of equations (linear/polynomial/exponential/logarithmic/power) were fitted. Among them, polynomial equation was found to be the best fit (highest coefficient of determination, R(2)) for prediction of texture using color properties for bananas. The pulp firmness, peel toughness and pulp toughness showed R(2) above 0.84 with indicating its potentiality of the fitted equations for prediction of textural profile of bananas non-destructively using 'a' value.

Color printing enabled by phase change materials on paper substrate

Science.gov (United States)

Ji, Hong-Kai; Tong, Hao; Qian, Hang; Liu, Nian; Xu, Ming; Miao, Xiang-Shui

2017-12-01

We have coated phase change materials (PCMs) on rough and flexible substrates to achieve multicolor changeable devices. The principle of the device is based on an earlier discovery that lights have strong interference effect in PCM films, leading to various colors by reflection. In this work, paper substrates are laminated by parylene layers to protect the device from water before coated with functional PCM films. The PCM-based color printing (PCP) on paper is not affected by rough surfaces and shows a similar color appearance as that on smooth surfaces. In particular, the color-printed device can be patterned by UV lithography to display a clear and tunable optical image, and it exhibits a low sensitivity to the angle of view. Such PCP has potential applications for low-cost, disposable, and flexible displays.

Relationship between the color stability and impurity profile of cefotaxime sodium.

Science.gov (United States)

Sun, Hua; Cui, Xuejun; Liu, Baoshu; Zhang, Junli

2017-09-15

The color grade, mainly introduced in the processes of semisynthesis and storage, is an important index used to evaluate the quality of cefotaxime sodium. Because the drug itself is prone to degradation under susceptible conditions, including those involving moisture, heat, ultraviolet light, acids, alkalis, and oxidants, and a series of degradation products as impurities are generated. In this study, the factors affecting color grade stability and the degradation mechanisms of cefotaxime sodium were investigated by designing different accelerated stability tests under the aforementioned conditions. The degradation extent was studied by using analytical methods, such as a solution color comparison method, ultraviolet spectrophotometry, and HPLC. The relationship between the color grade stability of cefotaxime sodium and its impurity profile has been explored, and a reasonable degradation mechanism has been proposed. The manufacturing conditions of inspection have been optimized, and a scientific basis for drug packaging, storage, and transportation conditions has been established. The results show that the color grade stability of cefotaxime sodium is related to the impurity profile to some degree, and the difference between the actual color and the standard color can reflect the levels of impurities to some extent. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of air-polishing powders on color stability of composite resins

Directory of Open Access Journals (Sweden)

Ahmet Umut Güler

2011-10-01

Full Text Available OBJECTIVES: The purpose of this study was to investigate the effect of different air-polishing powders on the color stability of different types of composite resin restorative materials. MATERIAL AND METHODS: Thirty cylindrical specimens (15×2 mm were prepared for each of 7 composite resin restorative materials. All specimens were polished with a series of aluminum oxide polishing discs (Sof-Lex. The prepared specimens of each composite resin were randomly divided into 3 groups of 10 specimens each, for control (Group-C and two air-powder applications (Group-CP: Cavitron Prophy-Jet; Group-PS: Sirona ProSmile prophylaxis powder. A standard air-polishing unit (ProSmile Handly was used. All specimens were air-powdered for 10 s at 4-bar pressure. The distance of the spray nosel from the specimens was approximately 10 mm and angulation of the nosel was 90°. Specimens were stored in 100 mL of coffee (Nescafe Classic for 24 h at 37°C. Color measurement of all specimens was recorded before and after exposure to staining agent with a colorimeter (Minolta CR-300. Color differences (∆E* between the 2 color measurements (baseline and after 24 h storage were calculated. The data were analyzed with a 2-way ANOVA test, and mean values were compared by the Tukey HSD test (p.05 and these groups demonstrated the highest ∆E* values. For Filtek Silorane and IntenS, the highest ∆E* values were observed in Group-PS. The lowest ∆E* values for all composite resin groups were observed in Group-C. When comparing the 7 composite resin restorative materials, Aelite Aesthetic Enemal demonstrated significantly less ∆E* values than the other composite resins tested. The highest ∆E* values were observed in Quixfil. CONCLUSION: Except for Quixfil, all control groups of composite resins that were polished Sof-Lex exhibited clinically acceptable ∆E values (<3.7. Air-polishing applications increased the color change for all composite resin restorative materials

Cellulose, hemicelluloses, lignin and ash content of some organic materials and their suitability for use as paper pulp supplements.

Science.gov (United States)

Ververis, C; Georghiou, K; Danielidis, D; Hatzinikolaou, D G; Santas, P; Santas, R; Corleti, V

2007-01-01

Freshwater algal biomass and orange and lemon peels were assessed as tissue paper pulp supplements. Cellulose and hemicellulose contents of algal biomass were 7.1% and 16.3%, respectively, whereas for citrus peels cellulose content ranged from 12.7% to 13.6% and hemicellulose from 5.3% to 6.1%. For all materials, lignin and ash content was 2% or lower, rendering them suitable for use as paper pulp supplements. The addition of algal biomass to paper pulp increased its mechanical strength significantly. However, brightness was adversely affected by chlorophyll. The addition of citrus peels in paper pulp had no effect on breaking length, increased bursting strength and decreased tearing resistance. Brightness was negatively affected at proportions of 10%, because citrus peel particles behave as coloured pigments. The cost of both materials is about 45% lower than that of conventional pulp, resulting in a 0.9-4.5% reduction in final paper price upon their addition to the pulp.

Dental Pulp Defence and Repair Mechanisms in Dental Caries.

Science.gov (United States)

Farges, Jean-Christophe; Alliot-Licht, Brigitte; Renard, Emmanuelle; Ducret, Maxime; Gaudin, Alexis; Smith, Anthony J; Cooper, Paul R

2015-01-01

Dental caries is a chronic infectious disease resulting from the penetration of oral bacteria into the enamel and dentin. Microorganisms subsequently trigger inflammatory responses in the dental pulp. These events can lead to pulp healing if the infection is not too severe following the removal of diseased enamel and dentin tissues and clinical restoration of the tooth. However, chronic inflammation often persists in the pulp despite treatment, inducing permanent loss of normal tissue and reducing innate repair capacities. For complete tooth healing the formation of a reactionary/reparative dentin barrier to distance and protect the pulp from infectious agents and restorative materials is required. Clinical and in vitro experimental data clearly indicate that dentin barrier formation only occurs when pulp inflammation and infection are minimised, thus enabling reestablishment of tissue homeostasis and health. Therefore, promoting the resolution of pulp inflammation may provide a valuable therapeutic opportunity to ensure the sustainability of dental treatments. This paper focusses on key cellular and molecular mechanisms involved in pulp responses to bacteria and in the pulpal transition between caries-induced inflammation and dentinogenic-based repair. We report, using selected examples, different strategies potentially used by odontoblasts and specialized immune cells to combat dentin-invading bacteria in vivo.

Dental Pulp Defence and Repair Mechanisms in Dental Caries

Directory of Open Access Journals (Sweden)

Jean-Christophe Farges

2015-01-01

Full Text Available Dental caries is a chronic infectious disease resulting from the penetration of oral bacteria into the enamel and dentin. Microorganisms subsequently trigger inflammatory responses in the dental pulp. These events can lead to pulp healing if the infection is not too severe following the removal of diseased enamel and dentin tissues and clinical restoration of the tooth. However, chronic inflammation often persists in the pulp despite treatment, inducing permanent loss of normal tissue and reducing innate repair capacities. For complete tooth healing the formation of a reactionary/reparative dentin barrier to distance and protect the pulp from infectious agents and restorative materials is required. Clinical and in vitro experimental data clearly indicate that dentin barrier formation only occurs when pulp inflammation and infection are minimised, thus enabling reestablishment of tissue homeostasis and health. Therefore, promoting the resolution of pulp inflammation may provide a valuable therapeutic opportunity to ensure the sustainability of dental treatments. This paper focusses on key cellular and molecular mechanisms involved in pulp responses to bacteria and in the pulpal transition between caries-induced inflammation and dentinogenic-based repair. We report, using selected examples, different strategies potentially used by odontoblasts and specialized immune cells to combat dentin-invading bacteria in vivo.

Biological Effects of Provisional Resin Materials on Human Dental Pulp Stem Cells.

Science.gov (United States)

Jun, S-K; Mahapatra, C; Lee, H-H; Kim, H-W; Lee, J-H

This study investigated the in vitro cytotoxicity as well as the proinflammatory cytokine expression of provisional resin materials on primary cultured human dental pulp stem cells (hDPSCs). Five commercially available provisional resin materials were chosen (SNAP [SN], Luxatemp [LT], Jet [JE], Revotek LC [RL], and Vipi block [VB]). Eluates that were either polymerizing or already set were added to hDPSCs under serially diluted conditions divided into three different setting times (25% set, 50% set, and 100% set) and incubated for 24 hours with 2× concentrated culture media. Cell cytotoxicity tests were performed by LDH assay and live and dead confocal microscope images. The expression of proinflammatory cytokines in SN and VB was measured using cytokine antibody arrays. Data were analyzed using repeated measures analysis of variance (ANOVA) or ANOVA followed by the Tukey post hoc test at a significance level of pprovisional resin materials during polymerization (SN, LT, and JE) were cytotoxic to hDPSCs and may adversely affect pulp tissue.

STORAGE OF CHEMICALLY PRETREATED WHEAT STRAW – A MEANS TO ENSURE QUALITY RAW MATERIAL FOR PULP PREPARATION

Directory of Open Access Journals (Sweden)

Terttu Heikkilä

2010-07-01

Full Text Available The aim of this study was to evaluate effects of chemical pretreatment and storage on non-wood pulping and on pulp quality. The processes studied were hot water treatment followed by alkaline peroxide bleaching or soda cooking. The results showed that it is possible to store wheat straw outside for at least one year without significant changes in the raw material chemical composition and without adverse effects on the resulting pulp quality. The results are significant to the industry using non-woods to ensure the availability and the quality of the raw-material throughout the year in spite of the short harvesting time.

Development of a Direct Pulp-capping Model for the Evaluation of Pulpal Wound Healing and Reparative Dentin Formation in Mice.

Science.gov (United States)

Song, Minju; Kim, Sol; Kim, Terresa; Park, Sil; Shin, Ki-Hyuk; Kang, Mo; Park, No-Hee; Kim, Reuben

2017-01-12

Dental pulp is a vital organ of a tooth fully protected by enamel and dentin. When the pulp is exposed due to cariogenic or iatrogenic injuries, it is often capped with biocompatible materials in order to expedite pulpal wound healing. The ultimate goal is to regenerate reparative dentin, a physical barrier that functions as a "biological seal" and protects the underlying pulp tissue. Although this direct pulp-capping procedure has long been used in dentistry, the underlying molecular mechanism of pulpal wound healing and reparative dentin formation is still poorly understood. To induce reparative dentin, pulp capping has been performed experimentally in large animals, but less so in mice, presumably due to their small sizes and the ensuing technical difficulties. Here, we present a detailed, step-by-step method of performing a pulp-capping procedure in mice, including the preparation of a Class-I-like cavity, the placement of pulp-capping materials, and the restoration procedure using dental composite. Our pulp-capping mouse model will be instrumental in investigating the fundamental molecular mechanisms of pulpal wound healing in the context of reparative dentin in vivo by enabling the use of transgenic or knockout mice that are widely available in the research community.

Color printing enabled by phase change materials on paper substrate

Directory of Open Access Journals (Sweden)

Hong-Kai Ji

2017-12-01

Full Text Available We have coated phase change materials (PCMs on rough and flexible substrates to achieve multicolor changeable devices. The principle of the device is based on an earlier discovery that lights have strong interference effect in PCM films, leading to various colors by reflection. In this work, paper substrates are laminated by parylene layers to protect the device from water before coated with functional PCM films. The PCM-based color printing (PCP on paper is not affected by rough surfaces and shows a similar color appearance as that on smooth surfaces. In particular, the color-printed device can be patterned by UV lithography to display a clear and tunable optical image, and it exhibits a low sensitivity to the angle of view. Such PCP has potential applications for low-cost, disposable, and flexible displays.

Pulp-dentin Regeneration: Current State and Future Prospects.

Science.gov (United States)

Cao, Y; Song, M; Kim, E; Shon, W; Chugal, N; Bogen, G; Lin, L; Kim, R H; Park, N-H; Kang, M K

2015-11-01

The goal of regenerative endodontics is to reinstate normal pulp function in necrotic and infected teeth that would result in reestablishment of protective functions, including innate pulp immunity, pulp repair through mineralization, and pulp sensibility. In the unique microenvironment of the dental pulp, the triad of tissue engineering would require infection control, biomaterials, and stem cells. Although revascularization is successful in resolving apical periodontitis, multiple studies suggest that it alone does not support pulp-dentin regeneration. More recently, cell-based approaches in endodontic regeneration based on pulpal mesenchymal stem cells (MSCs) have demonstrated promising results in terms of pulp-dentin regeneration in vivo through autologous transplantation. Although pulpal regeneration requires the cell-based approach, several challenges in clinical translation must be overcome-including aging-associated phenotypic changes in pulpal MSCs, availability of tissue sources, and safety and regulation involved with expansion of MSCs in laboratories. Allotransplantation of MSCs may alleviate some of these obstacles, although the long-term stability of MSCs and efficacy in pulp-dentin regeneration demand further investigation. For an alternative source of MSCs, our laboratory developed induced MSCs (iMSCs) from primary human keratinocytes through epithelial-mesenchymal transition by modulating the epithelial plasticity genes. Initially, we showed that overexpression of ΔNp63α, a major isoform of the p63 gene, led to epithelial-mesenchymal transition and acquisition of stem characteristics. More recently, iMSCs were generated by transient knockdown of all p63 isoforms through siRNA, further simplifying the protocol and resolving the potential safety issues of viral vectors. These cells may be useful for patients who lack tissue sources for endogenous MSCs. Further research will elucidate the level of potency of these iMSCs and assess their

Effect of finishing and polishing on color stability of a nanofilled resin immersed in different media

Directory of Open Access Journals (Sweden)

Ana Luísa Botta Martins de OLIVEIRA

Full Text Available OBJECTIVE: The purpose of this study was to evaluate the effect of finishing and polishing on color stability of a nanofilled composite resin (Filtek Z350 XT according to different immersion media.MATERIAL AND METHOD: Composite disks (10 mm diameter, 2 mm thickness were prepared for each group (n = 6 using a stainless steel mold. The groups were divided according to the presence or absence of finishing and polishing procedure and immersion media (artificial saliva, artificial juice- KAPO(r Coca-Cola(rflavors: pineapple, orange, strawberry and grape. The finishing and polishing procedures were performed using Super -Snap(r disks. The specimens were stored in artificial saliva for 24 hours (baseline and were analyzed using a color spectrophotometer by CIELab system. Then, they were immersed in different media for 5 minutes, 3 times a day, every 4 hours during 60 days. They were stored in artificial saliva at 37 ± 1°C during the immersion intervals. After this time, new measure of color was performed. The data were analyzed using Kruskall-Wallis test and Mann- Whitney test. The significance level was 5%.RESULT: The results showed that the finishing/polishing not significantly influence the color stability of resin composite (p > 0.05. There was no statistically significant difference in the color stability of the studied resin after immersion in different media (p > 0.05.CONCLUSION: The finishing and polishing procedures and the immersion media did not have influence on color stability of nanofilled resin Filtek Z350 XT.

Effect of staining solutions and repolishing on color stability of direct composites

Directory of Open Access Journals (Sweden)

Fabrício Mariano Mundim

2010-06-01

Full Text Available OBJECTIVES: The purpose of this study was to assess the color change of three types of composite resins exposed to coffee and cola drink, and the effect of repolishing on the color stability of these composites after staining. MATERIALS AND METHODS: Fifteen specimens (15 mm diameter and 2 mm thick were fabricated from microhybrid (Esthet-X; Dentsply and Filtek Z-250; 3M ESPE and high-density hybrid (Surefil; Dentsply composites, and were finished and polished with aluminum oxide discs (Sof-Lex; 3M ESPE. Color of the specimens was measured according to the CIE L*a*b* system in a refection spectrophotometer (PCB 6807; BYK Gardner. After baseline color measurements, 5 specimens of each resin were immersed in different staining solutions for 15 days: G1 - distilled water (control, G2 - coffee, G3 - cola soft drink. Afterwards, new color measurement was performed and the specimens were repolished and submitted to new color reading. Color stability was determined by the difference (ΔE between the coordinates L*, a*, and b* obtained from the specimens before and after immersion into the solutions and after repolishing. RESULTS: There was no statistically signifcant difference (ANOVA, Tukey's test; p>0.05 among the ΔE values for the different types of composites after staining or repolishing. For all composite resins, coffee promoted more color change (ΔE>3.3 than distilled water and the cola soft drink. After repolishing, the ΔE values of the specimens immersed in coffee decreased to clinically acceptable values (ΔE<3.3, but remained signifcantly higher than those of the other groups. CONCLUSIONS: No signifcant difference was found among composite resins or between color values before and after repolishing of specimens immersed in distilled water and cola. Immersing specimens in coffee caused greater color change in all types of composite resins tested in this study and repolishing contributed to decrease staining to clinically acceptable �

Surface properties and color stability of an acrylic resin combined with an antimicrobial polymer

Directory of Open Access Journals (Sweden)

Ana Carolina Pero

Full Text Available INTRODUCTION: The occurrence of stomatitis is common since the surface characteristics of the dentures may act as reservoirs for microorganisms and have the potential to support biofilm formation. PURPOSE: To assess the surface properties (wettability/roughness and color stability of an acrylic resin combined with the antimicrobial polymer poly (2-tert-butylaminoethyl methacrylate (PTBAEMA. MATERIAL AND METHOD: Thirty disc-shaped specimens of an acrylic resin (Lucitone 550 were divided into three groups: 0% (control; 5% and 10% PTBAEMA. Surface roughness values (Ra were measured using a profilometer and wettability was determined through contact angle measurements using a goniometer and deionized water as a test liquid. Color data were measured with a spectrophotometer. Kruskal-Wallis and Dunn's test were used to compare roughness values. Wettability data were analyzed using ANOVA and Tukey's test. Color data were compared using the Student's t-test and ∆E values were classified according to the National Bureau of Standards (NBS. All statistical analyses were performed considering α=.05. RESULT: Significant differences (p<.05 were detected among the groups for roughness, wettability and color stability. According to the NBS, the color changes obtained in the 5% and 10% PTBAEMA groups were "appreciable" and "much appreciable", respectively. CONCLUSION: It could be concluded that PTBAEMA incorporation in an acrylic resin increased the roughness and wettability of surfaces and produced color changes with clinical relevance.

Advanced Plasmonic Materials for Dynamic Color Display.

Science.gov (United States)

Shao, Lei; Zhuo, Xiaolu; Wang, Jianfang

2018-04-01

Plasmonic structures exhibit promising applications in high-resolution and durable color generation. Research on advanced hybrid plasmonic materials that allow dynamically reconfigurable color control has developed rapidly in recent years. Some of these results may give rise to practically applicable reflective displays in living colors with high performance and low power consumption. They will attract broad interest from display markets, compared with static plasmonic color printing, for example, in applications such as digital signage, full-color electronic paper, and electronic device screens. In this progress report, the most promising recent examples of utilizing advanced plasmonic materials for the realization of dynamic color display are highlighted and put into perspective. The performances, advantages, and disadvantages of different technologies are discussed, with emphasis placed on both the potential and possible limitations of various hybrid materials for dynamic plasmonic color display. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Stability of cactus-pear powder during storage

Directory of Open Access Journals (Sweden)

Plúvia O. Galdino

2016-02-01

Full Text Available ABSTRACT The stability of cactus-pear powder, obtained by the process of spray drying for 40 days, was evaluated under controlled conditions of relative air humidity (83% and temperature (25 and 40 °C. The whole pulp was characterized with regard to its physico-chemical parameters: pH, total titratable acidity, soluble solids, water content, total solids, ashes, reducing sugars, total sugars, non-reducing sugars, luminosity, redness, yellowness and water activity. The stored samples in powder were evaluated every 10 days for water content, water activity, total titratable acidity and color (luminosity, redness and yellowness. The whole pulp was slightly acidic and perishable, due to the high water content. During storage, the packages did not prevent water absorption, thus increasing water content and, consequently, water activity. Yellowness oscillated along the storage time, but the predominance of the yellow color was not affected.

Vital Pulp Therapy—Current Progress of Dental Pulp Regeneration and Revascularization

Directory of Open Access Journals (Sweden)

Weibo Zhang

2010-01-01

Full Text Available Pulp vitality is extremely important for the tooth viability, since it provides nutrition and acts as biosensor to detect pathogenic stimuli. In the dental clinic, most dental pulp infections are irreversible due to its anatomical position and organization. It is difficult for the body to eliminate the infection, which subsequently persists and worsens. The widely used strategy currently in the clinic is to partly or fully remove the contaminated pulp tissue, and fill and seal the void space with synthetic material. Over time, the pulpless tooth, now lacking proper blood supply and nervous system, becomes more vulnerable to injury. Recently, potential for successful pulp regeneration and revascularization therapies is increasing due to accumulated knowledge of stem cells, especially dental pulp stem cells. This paper will review current progress and feasible strategies for dental pulp regeneration and revascularization.

Stability of bioactive compounds in butiá (Butia odorata) fruit pulp and nectar.

Science.gov (United States)

Hoffmann, Jessica Fernanda; Zandoná, Giovana Paula; Dos Santos, Priscila Silveira; Dallmann, Camila Müller; Madruga, Francine Bonemann; Rombaldi, Cesar Valmor; Chaves, Fábio Clasen

2017-12-15

Butia odorata is a palm tree native to southern Brazil whose fruit (known as butiá) and leaves are used to make many food products and crafts. Butiá contain several biologically active compounds with potential health benefits. However, processing conditions can alter quality attributes including bioactive compound content. This study evaluated the stability of bioactive compounds in butiá pulp upon pasteurization, during 12months of frozen storage, and in butiá nectar after a 3-month storage period. Pulp pasteurization resulted in a reduction in phenolic, flavonoid, carotenoid, and ascorbic acid contents. After a 12-month frozen storage period, flavonoid, phenolic, and ascorbic acid contents decreased while carotenoid content remained unaltered. Carotenoid, ascorbic acid, and phenolic contents were unaffected by the 3-month storage of butiá nectar; however, flavonoid content and antioxidant potential were reduced. Despite bioactive compound degradation upon heat treatment and storage, butiá nectar remained rich in phenolics, especially (-)-epicatechin, rutin, and (+)-catechin. Copyright © 2017 Elsevier Ltd. All rights reserved.

Color and oxidative stability of nitrite-free cured meat after gamma irradiation

International Nuclear Information System (INIS)

Shahidi, F.; Pegg, R.B.; Shamsuzzaman, K.

1991-01-01

The effects of 5 and 10 kGy irradiation on the color and oxidative stability of meats treated with nitrite or a nitrite-free curing system were investigated. The nitrite-free curing system consisted of the preformed cooked cured-meat pigment, sodium ascorbate and sodium tripolyphosphate with or without sodium acid pyrophosphate. Irradiation had no detrimental effects on the color or flavor of either cured samples. Polyphosphates had a beneficial effect on oxidative stability but had a slight detrimental effect on color stability of irradiated samples

Effect of varying core thicknesses and artificial aging on the color difference of different all-ceramic materials.

Science.gov (United States)

Dikicier, Sibel; Ayyildiz, Simel; Ozen, Julide; Sipahi, Cumhur

2014-11-01

Clinicians should reserve all-ceramics with high translucency for clinical applications in which high-level esthetics are required. Furthermore, it is unclear whether a correlation exists between core thickness and color change. The aim of this study was to examine the effects of different core thicknesses and artificial aging on the color stability of three all-ceramic systems. Ninety disc-shaped cores with different thicknesses (0.5 mm, 0.8 mm and 1.0 mm) were prepared from three all-ceramic systems, In-Ceram Alumina (IC), IPS e.max Press (EM) and Katana (K). The colors of the samples were measured with a spectrophotometer and the color parameters (L*, a*, b*, ΔE) were calculated according to the CIE L*a*b* (Commission Internationale de L'Eclairage) color system before and after aging. The effects of aging on color parameters were statistically significant (p artificial aging affected color stability of the all-ceramic materials tested.

Effects of air-polishing powders on color stability of composite resins.

Science.gov (United States)

Güler, Ahmet Umut; Duran, Ibrahim; Yücel, Ali Çağin; Ozkan, Pelin

2011-10-01

The purpose of this study was to investigate the effect of different air-polishing powders on the color stability of different types of composite resin restorative materials. Thirty cylindrical specimens (15×2 mm) were prepared for each of 7 composite resin restorative materials. All specimens were polished with a series of aluminum oxide polishing discs (Sof-Lex). The prepared specimens of each composite resin were randomly divided into 3 groups of 10 specimens each, for control (Group-C) and two air-powder applications (Group-CP: Cavitron Prophy-Jet; Group-PS: Sirona ProSmile prophylaxis powder). A standard air-polishing unit (ProSmile Handly) was used. All specimens were air-powdered for 10 s at 4-bar pressure. The distance of the spray nosel from the specimens was approximately 10 mm and angulation of the nosel was 90°. Specimens were stored in 100 mL of coffee (Nescafe Classic) for 24 h at 37°C. Color measurement of all specimens was recorded before and after exposure to staining agent with a colorimeter (Minolta CR-300). Color differences (∆E*) between the 2 color measurements (baseline and after 24 h storage) were calculated. The data were analyzed with a 2-way ANOVA test, and mean values were compared by the Tukey HSD test (p.05) and these groups demonstrated the highest ∆E* values. For Filtek Silorane and IntenS, the highest ∆E* values were observed in Group-PS. The lowest ∆E* values for all composite resin groups were observed in Group-C. When comparing the 7 composite resin restorative materials, Aelite Aesthetic Enemal demonstrated significantly less ∆E* values than the other composite resins tested. The highest ∆E* values were observed in Quixfil. Except for Quixfil, all control groups of composite resins that were polished Sof-Lex exhibited clinically acceptable ∆E values (<3.7). Air-polishing applications increased the color change for all composite resin restorative materials tested. Composite restorations may require re

Effect of sealant agents on the color stability and surface roughness of nanohybrid composite resins.

Science.gov (United States)

Dede, Doğu Ömür; Şahin, Onur; Koroglu, Aysegül; Yilmaz, Burak

2016-07-01

The effect of sealant agents on the surface roughness and color stability of nanohybrid composite resins is unknown. The purpose of this in vitro study was to evaluate the effect of sealant agents on the surface roughness and color stability of 4 nanohybrid composite resin materials. Forty disks (10×2 mm) were fabricated for each nanohybrid composite resin material (Z-550, Tetric EvoCeram, Clearfill Majesty, Ice) (N=160) and divided into 4 surface treatment groups: 1 conventional polishing (control) and 3 different sealant agent (Palaseal, Optiglaze, BisCover) coupling groups (n=10). The specimens were thermocycled, and surface roughness (Ra) values were obtained with a profilometer. Scanning electron microscope images were also recorded. CIELab color parameters of each specimen were measured with a spectrophotometer before and after 7 days of storage in a coffee solution. Color differences were calculated by the CIEDE 2000 (ΔE00) formula. The data were statistically analyzed by 2-way ANOVA and by the Tukey HSD test (α=.05). The surface treatment technique significantly affected the Ra values of the composite resins tested (Pcomposite resin material was also significant for ΔE00 values (Pcomposite resin groups, significant decreases in Ra were observed only for the Palaseal agent coupled composite resin groups (except Ice) compared with the control groups (Pcomposite resin group, except for BisCover applied Clearfill Majesty (Pcomposite resin groups, significant differences were observed between the color change seen with BisCover and other sealants for Clearfill Majesty composite resin (Pcomposite resins except for Ice produced smoother surfaces. All surface sealant agents provided less discoloration of nanohybrid composite resins after coffee staining compared with conventional polishing except for BisCover applied Clearfill Majesty composite resin. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All

EVALUATION OF LINERBOARD PROPERTIES FROM MALAYSIAN CULTIVATED KENAF SODA-ANTHRAQUINONE PULPS VERSUS COMMERCIAL PULPS

OpenAIRE

Ahmad Azizi Mossello; Jalaluddin Harun; Rushdan Ibrahim; Hossien Resalati; Seyed Rashid Fallah Shamsi; Paridah Md Tahir; Mohd Nor Mohad Yusoff

2010-01-01

Malaysian cultivated kenaf has been identified as a suitable raw material for linerboard production. This study examines the soda-antraquinone (soda-AQ) pulp of kenaf fibers versus old corrugated container (OCC) and unbleached softwood kraft pulps as the main sources for linerboard production. The results showed significant differences among the pulp properties. The unbleached kraft pulp with very high freeness required high beating to reach an optimized freeness and produced paper with the h...

Composition and color stability of anthocyanin-based extract from purple sweet potato

Directory of Open Access Journals (Sweden)

Xiu-li He

2015-09-01

Full Text Available AbstractPurple sweet potato (PSP can provide products with attractive color besides nutritious benefits in food processing. So, the compositions and color stability of an aqueous anthocyanin-based PSP extract were investigated in order to promote its wide use in food industry. PSP anthocyanins were extracted with water, and nine individual anthocyanins (48.72 ug mL–1 in total, 24.36 mg/100 g fresh PSP in yield were found by HPLC analysis. The PSP extract also contained 17.11 mg mL–1 of protein, 0.44 mg mL–1 of dietary fiber, 2.82 mg mL–1 of reducing sugars, 4.02 ug mL–1 of Se, 54.21 ug mL–1 of Ca and 60.83 ug mL–1 of Mg. Changes in color and stability of the PSP extract, as affected by pH, heat, light and extraction process, were further evaluated. Results indicated that PSP anthocyanins had good stability at pH 2.0-6.0, while the color of PSP extract kept stable during 30 days of storage at 20 °C in dark. Both UV and fluorescent exposure weakened the color stability of PSP extract and UV showed a more drastic effect in comparison. A steaming pretreatment of fresh PSP is beneficial to the color stability.

Effect of organosolv and soda pulping processes on the metals content of non-woody pulps.

Science.gov (United States)

González, M; Cantón, L; Rodríguez, A; Labidi, J

2008-09-01

In this work the effect of different pulping processes (ethyleneglycol, diethyleneglycol, ethanolamine and soda) of tow abounded raw materials (empty fruit bunches - EFB and rice straw) on the ash, silicates and metals (Fe, Zn, Cu, Pb, Mn, Ni and Cd) content of the obtained pulps have been studied. Results showed that pulps obtained by diethyleneglycol pulping process presented lower metals content (756 microg/g and 501 microg/g for EFB and rice straw pulp, respectively) than soda pulps (984 microg/g and 889 microg/g). Ethanolamine pulps presented values of holocellulose (74% and 77% for EFB and rice straw pulp, respectively), alpha-cellulose (74% and 69%), kappa number (18.7 and 18.5) and viscosity (612 and 90 6ml/g) similar to those of soda pulp, and lower lignin contents (11% and 12%).

OPTICAL PROPERTY ANALYSIS OF THERMALLY AND PHOTOLYTICALLY AGED EUCALYPTUS CAMALDULENSIS CHEMITHERMOMECHANICAL PULP (CTMP

Directory of Open Access Journals (Sweden)

Yao Chen,

2012-02-01

Full Text Available To investigate the optical properties of chemithermomechanical pulp (CTMP from Eucalyptus camaldulensis, one group of samples of CTMP was aged by heating, and another group was first subjected to bleaching with different bleaching agents, and then aging by exposure to sunlight. Chromophores were analyzed using diffuse reflectance UV-Vis spectra (DRUV, and the brightness and color parameters (L*, a*, b* were analyzed using colorimetry. Results showed that the color reactions of the pulp, upon heating, were enhanced in the presence of moisture. There was a linear relationship between the pulp initial moisture content (MC and the intensity of UV-Vis absorption. The contribution of different chromophores to pulp color was analyzed with the help of bleaching agents: hydrogen peroxide, sodium dithionite, and sodium borohydride. Sodium borohydride and hydrogen peroxide treatments resulted in a decrease in the absorption band at 280 nm along with the shoulder near 320 nm, which could be attributed to conjugated C=O and C=C systems. Similarly, sodium dithionite treatment also led to a decrease in absorption of the carbonyls and double bonds conjugated with aromatic double bonds. The chromaticity parameters of bleached pulp increased after exposure to sunlight. A correspondingly higher concentration of quinoid structures was found.

Incomplete caries removal and indirect pulp capping in primary molars: a randomized controlled trial.

Science.gov (United States)

Bressani, Ana Eliza Lemes; Mariath, Adriela Azevedo Souza; Haas, Alex Nogueira; Garcia-Godoy, Franklin; de Araujo, Fernando Borba

2013-08-01

To compare the effect of incomplete caries removal (ICR) and indirect pulp capping (IPC) with calcium hydroxide (CH) or an inert material (wax) on color, consistency and contamination of the remaining dentin of primary molars. This double-blind, parallel-design, randomized controlled trial included 30 children presenting one primary molar with deep caries lesion. Children were randomly assigned after ICR to receive IPC with CH or wax. All teeth were then restored with resin composite. Baseline dentin color and consistency were evaluated after ICR, and dentin samples were collected for contamination analyses using scanning electron microscopy. After 3 months, restorations were removed and the three parameters were re-evaluated. In both groups, dentin became significantly darker after 3 months. No cases of yellow dentin were observed after 3 months with CH compared to 33.3% of the wax cases (P Contamination changed significantly over time in CH and wax without significant difference between groups. It was concluded that CH and wax arrested the carious process of the remaining carious dentin after indirect pulp capping, but CH showed superior dentin color and consistency after 3 months.

Osteogenic differentiation of dental pulp stem cells under the influence of three different materials

DEFF Research Database (Denmark)

Ajlan, S. A.; Ashri, N. Y.; Aldahmash, Abdullah M.

2015-01-01

Background: Regeneration of periodontal tissues is a major goal of periodontal therapy. Dental pulp stem cells (DPSCs) show mesenchymal cell properties with the potential for dental tissue engineering. Enamel matrix derivative (EMD) and platelet-derived growth factor (PDGF) are examples of materi......Background: Regeneration of periodontal tissues is a major goal of periodontal therapy. Dental pulp stem cells (DPSCs) show mesenchymal cell properties with the potential for dental tissue engineering. Enamel matrix derivative (EMD) and platelet-derived growth factor (PDGF) are examples...

The effect of cocoa (Theobroma cacao L on the basic color stability of thermoplastic nylon resin dentures

Directory of Open Access Journals (Sweden)

Amiyatun Naini

2011-11-01

Full Text Available Nylon thermoplastic resin is material of choice for the making of flexible. This denture do not use wire retention, but has the physical properties of water absorption. In the oral cavity, it will always be in contact with food and beverages consumed. One of the foods that are consumed by the public is chocolate. This study aimed to determine the effect of cocoa (Theobroma cacao L on color stability of the thermoplastic nylon denture base. The study sample was thermoplastic nylon (valplast with a size of 10x10x2 mm soaked in the chocolate solution for 7 and 14 days. As the control, the sample soaked with distilled water. The color testing stability used was densitometer. There were significant differences between the control group (distilled water and the chocolate solution. This was due to dissolved components/tannin having a capillary flow diffusion into thermoplastic nylons that causing discoloration. The conclusion of this study, there was the effect of cocoa (Theobroma cacao L against the color stability of the nylon thermoplastic denture base. The longer time of immersion of nylon thermoplastic the greater the change in color.

Red pepper (Capsicum annuum) carotenoids as a source of natural food colors: analysis and stability-a review.

Science.gov (United States)

Arimboor, Ranjith; Natarajan, Ramesh Babu; Menon, K Ramakrishna; Chandrasekhar, Lekshmi P; Moorkoth, Vidya

2015-03-01

Carotenoids are increasingly drawing the attention of researchers as a major natural food color due to their inherent nutritional characteristics and the implicated possible role in prevention and protection against degenerative diseases. In this report, we review the role of red pepper as a source for natural carotenoids. The composition of the carotenoids in red pepper and the application of different methodologies for their analysis were discussed in this report. The stability of red pepper carotenoids during post-harvest processing and storage is also reviewed. This review highlights the potential of red pepper carotenoids as a source of natural food colors and also discusses the need for a standardized approach for the analysis and reporting of composition of carotenoids in plant products and designing model systems for stability studies.

An in vitro evaluation of cytotoxicity of curcumin against human dental pulp fibroblasts

Directory of Open Access Journals (Sweden)

Praveenkumar S Mandrol

2016-01-01

Full Text Available Objective: The objective of this study was to evaluate the cytotoxicity of curcumin to primary dental pulp fibroblasts in vitro. Materials and Methods: Dental pulp fibroblasts from primary maxillary central incisors were cultured and used for cytotoxicity tests after the fourth passage. Ninety-five percent curcumin was diluted with dimethylsulfoxide to prepare 100%, 50%, and 25% concentrations. Each concentration of curcumin was added in triplicate into 96-well microtiter plate containing the fibroblast culture at 104/well. Cells without treatment served as a control group. The number of viable cells after 48 hrs incubation at 37°C in a humidified atmosphere of 5 % CO2 and 95 % air was determined by the 3-(4, 5-dimethyl-thiazol-2-yl-2, 5-diphenyl-tetrazolium bromide (MTT assay. The relative viability of pulp cells was expressed as color intensity of the number in the experimental wells relative to that of the control group. Absorbances were read at 492 nm on a microplate reader with a background subtraction at 620 nm. Results: Cell viability of primary dental pulp fibroblasts to 25%, 50%, and 100% curcumin concentration was 174%, 310%, and 317%, respectively. Conclusions: Curcumin promotes cell viability and induces proliferation of primary dental pulp fibroblasts and has the potential to be developed into an economical and reliable medicament for vital pulp therapy.

Paper pulp waste—A new source of raw material for the synthesis of ...

Indian Academy of Sciences (India)

Unknown

Most effluent pollution ... pollution caused by this waste material. .... (IV) The present study utilizes a solid waste of paper pulp industries thus minimizing the environmental pollution. ... Taylor J R and Bull A C 1986 Ceramics—glaze technology.

Method for Forming Pulp Fibre Yarns Developed by a Design-driven Process

Directory of Open Access Journals (Sweden)

Tiia-Maria Tenhunen

2016-01-01

Full Text Available A simple and inexpensive method for producing water-stable pulp fibre yarns using a deep eutectic mixture composed of choline chloride and urea (ChCl/urea was developed in this work. Deep eutectic solvents (DESs are eutectic mixtures consisting of two or more components that together have a lower melting point than the individual components. DESs have been previously studied with respect to cellulose dissolution, functionalisation, and pre-treatment. This new method uses a mixture of choline chloride and urea, which is used as a swelling and dispersing agent for the pulp fibres in the yarn-forming process. Although the pulp seemed to form a gel when dispersed in ChCl/urea, the ultrastructure of the pulp was not affected. To enable water stability, pulp fibres were crosslinked by esterification using polyacrylic acid. ChCl/urea could be easily recycled and reused by distillation. The novel process described in this study enables utilisation of pulp fibres in textile production without modification or dissolution and shortening of the textile value chain. An interdisciplinary approach was used, where potential applications were explored simultaneously with material development from process development to the early phase prototyping.

78 FR 38877 - Kraft Pulp Mills NSPS Review

Science.gov (United States)

2013-06-28

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 60 [EPA-HQ-OAR-2012-0640] FRL-9829-3 RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule... comments on the May 23, 2013, proposed rule titled, ``Kraft Pulp Mills NSPS Review'' is being extended by...

78 FR 31315 - Kraft Pulp Mills NSPS Review

Science.gov (United States)

2013-05-23

... Kraft Pulp Mills NSPS Review; Proposed Rule #0;#0;Federal Register / Vol. 78 , No. 100 / Thursday, May...-OAR-2012-0640; FRL-9815-9] RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection... performance standards for kraft pulp mills. These revised standards include particulate matter emission limits...

The UV-VIS spectrophotometry applied to color and stability study in colored mortars

Directory of Open Access Journals (Sweden)

Alejandre, F. J.

1999-06-01

Full Text Available In the field of methodologies for color studying, a research of it has been done on colored mortars by applying uv-vis spectrophotometry, instrumental technique which can be used for solid materials works, and previously applied to building materials study. Results obtained show that the mentioned technique permits to evaluate quantitatively and qualitatively colors in an easy and objective way, besides nowadays advantages of the instrumental analysis: digital color register, computerized data processing, and precision and exactness increment in chromatic comparisons.

Dentro de las metodologías existentes para el estudio del color, se ha realizado una investigación del mismo en morteros coloreados por medio de la espectrofotometría UV-VIS, técnica instrumental que es adaptable al trabajo con materiales sólidos, y que ha sido aplicada anteriormente en el estudio de diversos materiales de construcción. Los resultados obtenidos muestran cómo la citada técnica permite además de evaluar cualitativamente y cuantitativamente los colores de forma sencilla y objetiva, el disponer de las ventajas que conlleva actualmente el análisis instrumental: registro digital del color, tratamiento informatizado de datos y aumento de precisión y exactitud en las comparaciones cromáticas.

Heat processing (HTST of umbu (Spondias tuberosa Arruda Câmara pulp

Directory of Open Access Journals (Sweden)

Emanuelle Araújo de Oliveira

2011-12-01

Full Text Available Umbu pulp is an important product in the economy of the northeastern region of Brazil, and its preservation can be ensured by heat treatment. A complete factorial design with 2 factors (time and temperature and 3 central points was used to verify the effect of the HTST process on the physicochemical, chemical, physical, microbiological, and sensory qualities of umbu pulps. The results showed that the heat treatments applied resulted in products without significant alterations on the physicochemical, chemical, and microbiological characteristics. With respect to color, the parameters L and a* were altered by increases in temperature indicating by darkening of color. The sensory evaluation indicated that a treatment of 88 °C for 10 seconds was the best processing condition due to the greater similarity of the resulting product to the reference sample (blanched pulp.

Viscoelastic Properties of Dental Pulp Tissue and Ramifications on Biomaterial Development for Pulp Regeneration.

Science.gov (United States)

Erisken, Cevat; Kalyon, Dilhan M; Zhou, Jian; Kim, Sahng G; Mao, Jeremy J

2015-10-01

A critical step in biomaterial selection effort is the determination of material as well as the biological properties of the target tissue. Previously, the selection of biomaterials and carriers for dental pulp regeneration has been solely based on empirical experience. In this study, first, the linear viscoelastic material functions and compressive properties of miniature pig dental pulp were characterized using small-amplitude oscillatory shear and uniaxial compression at a constant rate. They were then compared with the properties of hydrogels (ie, agarose, alginate, and collagen) that are widely used in tissue regeneration. The comparisons of the linear viscoelastic material functions of the native pulp tissue with those of the 3 hydrogels revealed the gel-like behavior of the pulp tissue over a relatively large range of time scales (ie, over the frequency range of 0.1-100 rps). At the constant gelation agent concentration of 2%, the dynamic properties (ie, storage and loss moduli and the tanδ) of the collagen-based gel approached those of the native tissue. Under uniaxial compression, the peak normal stresses and compressive moduli of the agarose gel were similar to those of the native tissue, whereas alginate and collagen exhibited significantly lower compressive properties. The linear viscoelastic and uniaxial compressive properties of the dental pulp tissue reported here should enable the more appropriate selection of biogels for dental pulp regeneration via the better tailoring of gelation agents and their concentrations to better mimic the dynamic and compressive properties of native pulp tissue. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Physical and Flavor Profiles of Arabica Coffee as Affected by Cherry Storage Before Pulping

Directory of Open Access Journals (Sweden)

Yusianto .

2014-08-01

Full Text Available Harvesting and pulping process of coffee cherry in the same day is inaccesible. Storage of coffee cherry before pulping was carried out incorrectly. Some storage treatments before pulping of Arabica coffee cherry had been examined at Indonesian Coffee and Cocoa Research Institute using Arabica coffee cherries from Andungsari Experimental Garden, Bondowoso, East Java. Treatments of the experiment were method and period of cherry storage. Methods of coffee cherry storage were put in plastic sacks; immerse in water, without water replacement; and immerse in water with daily water replacement. Period of coffee cherry storage were 0, 1, 2, 3, 4, 5, 6, and 7 days. After storage treatments, the coffee cherries were pulped, fermented, washed, sundried, and dehulled. The experiment were carried out using randomized block design with three replications. Observation of coffee cherry during storage periods was done on the physical and temperature. Observation of the green coffee were done on the color dan bulk density. The green coffee were roasted at medium roast level for sensory analysis. Observation of roasting profile were out-turn, bulk density and pH of roasted coffee. Sensory analysis used Specialty Coffee Association of America method. Methods and period of cherry storage before pulping significanly influence on the cherry color, parchment color, green coffee color, and the flavor profile of Arabica coffee. Color of dry parchment changed to be red-brown becouse of cherry immersed in water for two days or more. In plastic sacks, Arabica coffee cherry may be stored only for two days, but underwater with or without water replacement, should be not more than five days. Green and sensory quality of Arabica coffee will be deteriorated after five days storage underwater. Coffee cherry storage immerse in water with daily replacing water may improve sensory quality of Arabica coffee.Key word: Arabica coffe, storage, pulping, flavor, physical

[Application of Fourier transform attenuated total reflection infrared spectroscopy in analysis of pulp and paper industry].

Science.gov (United States)

Zhang, Yong; Cao, Chun-yu; Feng, Wen-ying; Xu, Ming; Su, Zhen-hua; Liu, Xiao-meng; Lü, Wei-jun

2011-03-01

As one of the most powerful tools to investigate the compositions of raw materials and the property of pulp and paper, infrared spectroscopy has played an important role in pulp and paper industry. However, the traditional transmission infrared spectroscopy has not met the requirements of the producing processes because of its disadvantages of time consuming and sample destruction. New technique would be needed to be found. Fourier transform attenuated total reflection infrared spectroscopy (ATR-FTIR) is an advanced spectroscopic tool for nondestructive evaluation and could rapidly, accurately estimate the production properties of each process in pulp and paper industry. The present review describes the application of ATR-FTIR in analysis of pulp and paper industry. The analysis processes will include: pulping, papermaking, environmental protecting, special processing and paper identifying.

Mineral Trioxide Aggregate and Portland Cement for Direct Pulp Capping in Dog: A Histopathological Evaluation

Directory of Open Access Journals (Sweden)

Maryam Bidar

2014-09-01

Full Text Available Background and aims. Mineral trioxide aggregate and calcium hydroxide are considered the gold standard pulp-capping materials. Recently, Portland cement has been introduced with properties similar to those of mineral trioxide aggregate. His-topathological effects of direct pulp capping using mineral trioxide aggregate and Portland cements on dog dental pulp tis-sue were evaluated in the present study. Materials and methods. This histopatological study was carried out on 64 dog premolars. First, the pulp was exposedwith a sterile bur. Then, the exposed pulp was capped with white or gray mineral trioxide aggregates and white or gray Port-land cements in each quadrant and sealed with glass-ionomer. The specimens were evaluated under a light microscope after 6 months. Statistical analysis was carried out using Kruskal-Wallis test. Statistical significance was defined at α=5%. Results. There was no acute inflammation in any of the specimens. Chronic inflammation in white and gray mineral triox-ide aggregates and white and gray Portland cements was reported to be 45.5%, 27.3%, 57.1% and 34.1%, respectively. Al-though the differences were not statistically significant, severe inflammation was observed mostly adjacent to white mineral trioxide aggregate. The largest extent of increased vascularization (45% and the least increase in fibrous tissue were ob-served adjacent to white mineral trioxide aggregate, with no significant differences. In addition, the least calcified tissue formed adjacent to white mineral trioxide aggregate, although the difference was not significant. Conclusion. The materials used in this study were equally effective as pulp protection materials following direct pulp cap-ping in dog teeth.

Two-color stabilization of atomic hydrogen in circularly polarized laser fields

International Nuclear Information System (INIS)

Bauer, D.; Ceccherini, F.

2002-01-01

The dynamic stabilization of atomic hydrogen against ionization in high-frequency single- and two-color, circularly polarized laser pulses is observed by numerically solving the three-dimensional, time-dependent Schroedinger equation. The single-color case is revisited and numerically determined ionization rates are compared with both, the exact and the approximate high-frequency Floquet rates. The positions of the peaks in the photoelectron spectra can be explained with the help of dressed initial states. In two-color laser fields of opposite circular polarization, the stabilized probability density may be shaped in various ways. For laser frequencies ω 1 and ω 2 =nω 1 , n=2,3,..., and sufficiently large excursion amplitudes (n+1) distinct probability density peaks are observed. This may be viewed as the generalization of the well-known 'dichotomy' in linearly polarized laser fields, i.e, as 'trichotomy', 'quatrochotomy', 'pentachotomy' etc. All those observed structures and their 'hula-hoop'-like dynamics can be understood with the help of high-frequency Floquet theory and the two-color Kramers-Henneberger transformation. The shaping of the probability density in the stabilization regime can be realized without additional loss in the survival probability, as compared to the corresponding single-color results

Application of thermoalkalophilic xylanase from Arthrobacter sp. MTCC 5214 in biobleaching of kraft pulp

Digital Repository Service at National Institute of Oceanography (India)

Khandeparker, R.; Bhosle, N.B.

released by enzyme treatment showed a characteristic peak at 280 nm indicating the presence of lignin in the released coloring matter. Enzymatic prebleaching of kraft pulp showed 20 % reduction in kappa number of the pulp without much change in viscosity...

Low Temperature Soda-Oxygen Pulping of Bagasse

OpenAIRE

Fengxia Yue; Ke-Li Chen; Fachuang Lu

2016-01-01

Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today’s pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum coo...

Natural colorants: Pigment stability and extraction yield enhancement via utilization of appropriate pretreatment and extraction methods.

Science.gov (United States)

Ngamwonglumlert, Luxsika; Devahastin, Sakamon; Chiewchan, Naphaporn

2017-10-13

Natural colorants from plant-based materials have gained increasing popularity due to health consciousness of consumers. Among the many steps involved in the production of natural colorants, pigment extraction is one of the most important. Soxhlet extraction, maceration, and hydrodistillation are conventional methods that have been widely used in industry and laboratory for such a purpose. Recently, various non-conventional methods, such as supercritical fluid extraction, pressurized liquid extraction, microwave-assisted extraction, ultrasound-assisted extraction, pulsed-electric field extraction, and enzyme-assisted extraction have emerged as alternatives to conventional methods due to the advantages of the former in terms of smaller solvent consumption, shorter extraction time, and more environment-friendliness. Prior to the extraction step, pretreatment of plant materials to enhance the stability of natural pigments is another important step that must be carefully taken care of. In this paper, a comprehensive review of appropriate pretreatment and extraction methods for chlorophylls, carotenoids, betalains, and anthocyanins, which are major classes of plant pigments, is provided by using pigment stability and extraction yield as assessment criteria.

Physico-chemical, microbiological and sensory stability of chemically preserved mango pulp

International Nuclear Information System (INIS)

Akhtar, S.; Riaz, M.; Nisar, A.

2010-01-01

The effect of sodium benzoate (SB) and potassium metabisulphite (PMS) at various concentrations on chemical, microbiological and sensory quality of mango pulp during storage was assessed. Inhibitory activity of the chemical preservatives and their effect on chemical and sensory attributes was tested periodically by simulating the industrial mango pulp storage in the lab (30-42 deg. C in the dark), for a period of 90 days. Protein, fats, decreased while ash content and total soluble solid (TSS) increased during the storage period. A slight progressive decline in pH was observed with a proportional increase (p<0.05) in the acidity of the stored pulp samples. Significant inhibition of the total bacterial count (TBC) was observed on applying the specified concentrations, however PMS was shown to be more inhibitory. Storage time significantly (p<0.05) increased the CFU/g of the pulp samples as the maximum growth was observed after 90 days of storage. Sensory characteristics of the juice prepared from treated mango pulp samples were affected negatively on addition of preservatives however, the samples were accepted by the judges even after three months of storage. (author)

Tunable structural color in organisms and photonic materials for design of bioinspired materials

International Nuclear Information System (INIS)

Fudouzi, Hiroshi

2011-01-01

In this paper, the key topics of tunable structural color in biology and material science are overviewed. Color in biology is considered for selected groups of tropical fish, octopus, squid and beetle. It is caused by nanoplates in iridophores and varies with their spacing, tilting angle and refractive index. These examples may provide valuable hints for the bioinspired design of photonic materials. 1D multilayer films and 3D colloidal crystals with tunable structural color are overviewed from the viewpoint of advanced materials. The tunability of structural color by swelling and strain is demonstrated on an example of opal composites. (topical review)

Tunable structural color in organisms and photonic materials for design of bioinspired materials

Directory of Open Access Journals (Sweden)

Hiroshi Fudouzi

2011-01-01

Full Text Available In this paper, the key topics of tunable structural color in biology and material science are overviewed. Color in biology is considered for selected groups of tropical fish, octopus, squid and beetle. It is caused by nanoplates in iridophores and varies with their spacing, tilting angle and refractive index. These examples may provide valuable hints for the bioinspired design of photonic materials. 1D multilayer films and 3D colloidal crystals with tunable structural color are overviewed from the viewpoint of advanced materials. The tunability of structural color by swelling and strain is demonstrated on an example of opal composites.

Tunable structural color in organisms and photonic materials for design of bioinspired materials

Science.gov (United States)

Fudouzi, Hiroshi

2011-01-01

In this paper, the key topics of tunable structural color in biology and material science are overviewed. Color in biology is considered for selected groups of tropical fish, octopus, squid and beetle. It is caused by nanoplates in iridophores and varies with their spacing, tilting angle and refractive index. These examples may provide valuable hints for the bioinspired design of photonic materials. 1D multilayer films and 3D colloidal crystals with tunable structural color are overviewed from the viewpoint of advanced materials. The tunability of structural color by swelling and strain is demonstrated on an example of opal composites. PMID:27877454

Dimensional Stability of Color-Changing Irreversible Hydrocolloids after Disinfection

Directory of Open Access Journals (Sweden)

Khaledi AAR

2015-03-01

Full Text Available Statement of Problem: Disinfection of dental impressions is a weak point in the dental hygiene chain. In addition, dental office personnel and dental technicians are endangered by cross-contamination. Objectives: This study aimed to investigate the dimensional stability of two color-changing irreversible hydrocolloid materials (IH after disinfection with glutaraldehyde. Materials and Methods: In this in vitro study, impressions were made of a master maxillary arch containing three reference inserts on the occlucal surface of the left and right maxillary second molars and in the incisal surface of the maxillary central incisors. Two types of color-changing irreversible hydrocolloid (tetrachrom, cavex were used. Glutaraldehyde 2% was used in two methods of spraying and immersion to disinfect the impressions. The control group was not disinfected. Casts were made of type IV gypsum. The linear dimensional change of the stone casts was measured with a profile projector. For statistical analysis, Kruskall-Wallis and Mann-Witney tests were used (α=0.05. Results: By immersion method, the casts fabricated from tetrachrom were 0.36% larger in the anteroposterior (AP and 0.05% smaller in cross arch (CA dimensions; however, the casts prepared after spraying of tetrachrom were 0.44% larger in the AP and 0.10% smaller in CA dimensions. The casts made from Cavex were 0.05% smaller in the AP and 0.02% smaller in CA dimensions after spraying and 0.01% smaller in the AP and 0.003% smaller in CA dimensions after immersion. Generally there were not significant differences in AP and CA dimensions of the experimental groups compared to the control (p > 0.05. Conclusions: Disinfection of the tested color-changing irreversible hydrocolloids by glutaraldahyde 2% did not compromise the accuracy of the obtained casts.

PRODUCTION OF DISSOLVING GRADE PULP FROM ALFA

Directory of Open Access Journals (Sweden)

Baya Bouiri

2010-02-01

Full Text Available Alfa, also known as Stipa tenacissimaI or “halfa”, is grown in North Africa and south Spain. Due to its short fiber length, paper made from alfa pulp retains bulk and takes block letters well. In this study alfa was evaluated for bleached pulp production. Two cellulose pulps with different chemical compositions were pulped by a conventional kraft process. One sample was taken from the original alfa material and another from alfa that had been pretreated by diluted acid. The pulp produced from the pretreated alfa was bleached by the elemental-chlorine-free sequences DEPD and DEDP. The yield, Kappa number, brightness, and α- cellulose content of bleached and unbleached pulps were evaluated. The results showed that during the chemical pulping process, treated alfa cooked more easily than the original alfa. The treated alfa pulp also showed very good bleaching, reaching a brightness level of 94.8% ISO with a yield of 93.6% at an α-cellulose content 96.8(% with a DEDP bleaching sequence, compared to 83.2% ISO brightness level, 92.8% yield, and 95.1% α-cellulose content for bleached pulp with a DEPD bleaching sequence. Therefore, this alfa material could be considered as a worthwhile choice for cellulosic fiber supply.

Potassium hydroxide pulping of rice straw in biorefinery initiatives.

Science.gov (United States)

Jahan, M Sarwar; Haris, Fahmida; Rahman, M Mostafizur; Samaddar, Purabi Rani; Sutradhar, Shrikanta

2016-11-01

Rice straw is supposed to be one of the most important lignocellulosic raw materials for pulp mill in Asian countries. The major problem in rice straw pulping is silica. The present research is focused on the separation of silica from the black liquor of rice straw pulping by potassium hydroxide (KOH) and pulp evaluation. Optimum KOH pulping conditions of rice straw were alkali charge 12% as NaOH, cooking temperature 150°C for 2h and material to liquor ratio, 1:6. At this condition pulp yield was 42.4% with kappa number 10.3. KOH pulp bleached to 85% brightness by D0EpD1 bleaching sequences with ClO2 consumption of 25kg/ton of pulp. Silica and lignin were separated from the black liquor of KOH pulping. The amount of recovered silica, lignin and hemicelluloses were 10.4%, 8.4% and 13.0%. The papermaking properties of KOH pulp from rice straw were slightly better than those of corresponding NaOH pulp. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pulp-Capping with Mineral Trioxide Aggregate

Directory of Open Access Journals (Sweden)

Peycheva Kalina

2015-11-01

Full Text Available There are two considerations for direct pulp capping - accidental mechanical pulp exposure and exposure caused by caries. Mineral trioxide aggregate (MTA was used as pulp-capping material to preserve the vitality of the pulpal tissues. Follow-up examinations revealed that treatment was successful in preserving pulpal vitality and continued development of the tooth. On the basis of available information, it appears that MTA is the material of choice for some clinical applications. Material and methods: Cases 18 - 8 teeth with grey MTA, 10 teeth with white MTA; diagnose: Pulpitis chronica ulcerosa, Electro pulpal test (EOD - 30-35 μA, pre-clinical X-ray - without changes in the structures, follow ups for 4 years. Successful treatments: without clinical symptoms and changes in the X-rays: 5 teeth with grey MTA, 8 teeth with white MTA for period of 4 years. Unsuccessful treatments: Clinical symptoms and sometimes changes in the X-ray: 3 with grey MTA, 2 with white MTA. MTA is an appropriate material for pulp-capping and follow-up examinations revealed that the treatment was successful in preserving pulpal vitality.

EVALUATION OF LINERBOARD PROPERTIES FROM MALAYSIAN CULTIVATED KENAF SODA-ANTHRAQUINONE PULPS VERSUS COMMERCIAL PULPS

Directory of Open Access Journals (Sweden)

Ahmad Azizi Mossello

2010-06-01

Full Text Available Malaysian cultivated kenaf has been identified as a suitable raw material for linerboard production. This study examines the soda-antraquinone (soda-AQ pulp of kenaf fibers versus old corrugated container (OCC and unbleached softwood kraft pulps as the main sources for linerboard production. The results showed significant differences among the pulp properties. The unbleached kraft pulp with very high freeness required high beating to reach an optimized freeness and produced paper with the highest strength properties, except for tear resistance. The OCC gave paper with the lowest strength properties. In the case of kenaf fractions, bast pulp with high freeness needed less beating than softwood and produced paper with high tear resistance. Core fiber, which had the lowest freeness and highest drainage time, led to paper with high strength but very low tear resistance. Kenaf whole stem pulp showed intermediate properties between core and bast and close to those of unbleached softwood pulp, but with very lower beating requirement. Finally, kenaf whole stem, due to its strength properties, moderate separation cost, and simple pulping process, was judged to be more suitable for commercialization for linerboard production in Malaysia.

Color stability of shade guides after autoclave sterilization.

Science.gov (United States)

Schmeling, Max; Sartori, Neimar; Monteiro, Sylvio; Baratieri, Luiz

2014-01-01

This study evaluated the influence of 120 autoclave sterilization cycles on the color stability of two commercial shade guides (Vita Classical and Vita System 3D-Master). The specimens were evaluated by spectrophotometer before and after the sterilization cycles. The color was described using the three-dimensional CIELab system. The statistical analysis was performed in three chromaticity coordinates, before and after sterilization cycles, using the paired samples t test. All specimens became darker after autoclave sterilization cycles. However, specimens of Vita Classical became redder, while those of the Vita System 3D-Master became more yellow. Repeated cycles of autoclave sterilization caused statistically significant changes in the color coordinates of the two shade guides. However, these differences are considered clinically acceptable.

PENGGUNAAN ASAM PERASETAT PADA PROSES DELIGNIFIKASI PULP ACETOSOLV DARI AMPAS TEBU DAN BAMBU BETUNG

Directory of Open Access Journals (Sweden)

Ahmad Sapta Zuidar

2014-07-01

Full Text Available Acetosolv process produced dark pulp because of the high lignin content.  Therefore ,  delignification  process is needed. This process uses peracetic acid to improve pulp qualities. The objective of this research was to determine the effect of different concentrations of peracetic acid against the characteristics of pulp acetosolv from bagasse and bamboo betung.  The research was arranged in a Complete Randomized Block Design with a single treatment and 4 replications.  The treatment used peracetic acid with six levels concentration (9%, 11%, 13%, 15%, 17%, 19% at a temperature of 85oC for 3 hours. The homogenity and additivity of the data were  analyzed using Bartlett and Tuckey Tests, then they were analyze for ANOVA to see if there is any difference among means, and then processed further using  Least Significant Difference at level of 1% and 5%.  The results showed that the concentration of peracetic acid had significant effect on yield, cellulose, hemicellulose, lignin, and organoleptic color pulp from bagasse and bamboo betung.  The best results showed that the concentration of peracetic acid 15% with cooking duration of  3 hours gave the best pulp. The pulp contained 85.837% of cellulose , 7.757% of hemicellulose , 1.758% of lignin , 73.048% of yield  and  the average organoleptic score for the pulp color was 4.3. Keywords:   acetosolv pulp,  baggase, bamboo,  delignification, paracetic acid

Paper pulp waste—A new source of raw material for the synthesis of ...

Indian Academy of Sciences (India)

A synthetic porous ceramic composite material consisting of the mullite, cordierite and cristobalite phases is produced from a mixture of paper pulp waste and clay by reaction sintering at 1400°C. Physicomechanical properties such as bulk density, porosity, cold crushing strength and cold modulus of rupture have been ...

Effects of Soda-Anthraquinone Pulping Variables on the Durian Rind Pulp and Paper Characteristics: A Preliminary Test

Science.gov (United States)

Rizal Masrol, Shaiful; Irwan Ibrahim, Mohd Halim; Adnan, Sharmiza; Rahmad Talib, Mohd; Sian, Lau Lee

2017-08-01

Good combination of pulping variables is required to obtain the quality pulp and paper characteristics. Thus, in this preliminary work, naturally dried durian rind were pulped under Soda-Anthraquinone (Soda-AQ) pulping process with 18% to 22% alkali charge, 0% to 0.1% Anthraquinone (AQ) charge, 90 minutes to 150 minutes of cooking time and 150°C to 170°C to investigate the effect of pulping variables on the characteristics of the pulp and paper. Pulping condition with 0% of AQ charge was also conducted for comparison. Results indicated that the best screen yield percentage, reject yield percentage, freeness, drainage time, tear index, number of folds and optical properties were shown by the pulp produced with combination of the highest active alkali (22%), AQ charge (0.1%), cooking time (150 minutes) and cooking temperature (170°C) except apparent density, tensile index and burst index. This preliminary result shows that the optimum quality of durian rind pulp as a potential papermaking raw material pulp could be produced by selecting the good combination of pulping variables which influences the pulp and paper characteristics.

Estabilidade da polpa do bacuri (Platonia insignis Mart. congelada por 12 meses Stability of the bacuri pulp (Platonia insignis Mart. frozen for 12 months

Directory of Open Access Journals (Sweden)

Virlane Kelly Lima da Silva

2010-10-01

Full Text Available Conduziu-se este trabalho, com o objetivo de realizar o processamento e avaliar a estabilidade da polpa de bacuri (Platonia insignis Mart. submetida ao congelamento durante 12 meses. Durante o período de armazenamento não ocorreram alterações significativas nas características físico-químicas da polpa quanto aos teores de sólidos solúveis, pH, atividade de água, açúcares totais e redutores, vitamina C, compostos fenólicos poliméricos e oligoméricos, pectina total e solúvel e cor L, a* , b*, enquanto que a acidez total e relação SST/AT variaram com o tempo de armazenamento. Os compostos fenólicos dímeros apresentaram aumento em função do tempo. Pelos resultados obtidos, a polpa de bacuri não pode ser considerada uma boa fonte de vitamina C. Por outro lado, apresenta baixos teores de compostos fenólicos caracterizando a polpa como, potencialmente pouco adstringente e com potencial para o processamento. A qualidade microbiológica não foi alterada durante o período de armazenamento. Os resultados apontam a eficiência do congelamento na manutenção das características físico-químicas e microbiológicas da polpa de bacuri.The objective of this work was to process and evaluate the stability of the bacuri (Platonia insignis Mart. pulp submitted to freezing for 12 months. During the storage period there were significant changes in the physiochemical characteristics of the pulp as for the content of total soluble solids, pH, water activity, total and reducing sugars, vitamin C, polimer and oligomeric phenolic compounds , total and soluble pectin and color L, the a*, b *,while total acidity and soluble solids varied with the storange period. The dimers phenolic compounds incresead with the time. According to the results, the bacuri pulp cannot be considered a good source of vitamin C, but it presents low contents of phenolic compounds characterizing the pulp as little astringent, thus showing potential for the processing

Biogas generation apple pulp.

Science.gov (United States)

Llaneza Coalla, H; Blanco Fernández, J M; Morís Morán, M A; López Bobo, M R

2009-09-01

In view of the pressing problem that appears in our region (Asturias, north of Spain) with the residues from the cider production, it was decided to test this kind of material as a co-substrate joint with slaughterhouse waste in a laboratory unit. The anaerobic digestion of apple pulp was investigated for biogas production. This paper presents the results where apple pulp was co-digested with slaughterhouse waste (pig intestine and bovine stomach content) in a biogas laboratory unit (10 l CSTR reactor). The production of biogas has reached very satisfactory values during the whole test (0.8m(3)kg(-1)OTS), verifying that the process is kept in stable conditions of pH (near 8.0), and the volatile fatty acids was always underneath 3000 mg/l, when the pulp amount was lower than 100g in mesophilic conditions. The fat concentration into the digester remained always below the value that causes inhibition of the methanogenic bacteria, 500 mg/l. Finally, methane concentration (77-80%) and H(2)S concentration (400 ppm) in the biogas, they were similar to those obtained when the test was run out in the absence of apple pulp. The process efficiency with respect to COD removal was high, near 80% of the total COD. Finally, inhibitory effects of methanogenic bacteria were observed when pulp concentration was around 10% in the input material.

Influence of different pulp capping materials to induce coronal tooth discoloration

Directory of Open Access Journals (Sweden)

Natália Gomes e Silva Leonardo

2016-06-01

Conclusions: This study demonstrated that all tested materials induced teeth shade changes after 30 days of simulated pulpotomy. The mean variation of color was similar between groups and CAC caused the higher color change.

Optimum dose of 2-hydroxyethyl methacrylate based bonding material on pulp cells toxicity

OpenAIRE

Saraswati, Widya

2010-01-01

Background: 2-hydroxyethyl methacrylate (HEMA), one type of resins commonly used as bonding base material, is commonly used due to its advantageous chemical characteristics. Several preliminary studies indicated that resin is a material capable to induce damage in dentin-pulp complex. It is necessary to perform further investigation related with its biological safety for hard and soft tissues in oral cavity. Purpose: The author performed an in vitro test to find optimum dose of HEMA resin mon...

Development of the RGB LEDs color mixing mechanism for stability the color temperature at different projection distances.

Science.gov (United States)

Hung, Chih-Ching

2015-01-01

In lighting application, the color mixing of the RGB LEDs can provide more color selection in correlated color temperature and color rendering. Therefore, the purpose of this study is to propose a RGB color mixing mechanism by applying the mechanism design. Three sets of lamp-type RGB LEDs are individually installed on three four-bar linkages. A crank is used to drive three groups of RGB LEDs lamp-type to project lights onto a single plane in order to mix the lights. And, simulations of the illuminance and associated color temperatures are conducted by changing the distance to the projection plane, under the assumption that the stability of the color temperature of the projected light does not change according to the projecting height. Thus, the effect of change in the color temperature on color determination by the humans' eyes was avoided. The success of the proposed method will allow medical personnel to choose suitable wavelengths and color temperatures according to the particular requirements of their medical-examination environments.

A novel application of resin in pulp in the metallurgical industry

International Nuclear Information System (INIS)

Fleming, C.A.; Cromberge, G.

1985-01-01

The results are presented of several small-scale pilot-plant investigations that demonstrate the feasibility of a resin-in-pulp process for the combined extraction of gold and uranium. Both metals are leached into an aqueous solution as anionic complexes, and, under appropriate conditions, both metal anions can be stabilized in the same solution and extracted from that solution by anion-exchange resins. Three different lead materials containing gold and uranium were tested, and several configurations for leaching and the resin-in-pulp process were examined so that the efficiency of extraction of the process could be demonsrated. The results of the various pilot-plant investigations are discussed with particular emphasis on the deportment of gold and uranium during the leaching extraction, and elution steps

Effect of various de-anodizing techniques on the surface stability of non-colored and colored nanoporous AAO films in acidic solution

Energy Technology Data Exchange (ETDEWEB)

Awad, Ahmed M. [Chemical Engineering & Pilot Plant Department, National Research Centre, Dokki, Giza (Egypt); Shehata, Omnia S. [Physical Chemistry Department, National Research Centre, Dokki, Giza (Egypt); Heakal, Fakiha El-Taib, E-mail: fakihaheakal@yahoo.com [Chemistry Department, Faculty of Science, Cairo University, Giza 12613 (Egypt)

2015-12-30

Highlights: • Three de-anodization methods were used during two-step fabrication of nanoporous AAO. • Electrolytic etching (EE), chemical etching with H{sub 3}PO{sub 4} (PE) or NaOH (HE) were adopted. • After the second anodizing step, HE film was the thinnest as compared to EE and HE. • Stability order of nanoporous AAO films in 0.5 M HCl solution was: PE > EE > HE. • For the colored films by electrodeposited Cu atoms, the order was: HE > EE > PE. - Abstract: Anodic aluminum oxide (AAO) is well known as an important nanostructured material, and a useful template in the fabrication of nanostructures. Nanoporous anodic alumina (PAA) with high open porosity was prepared by adopting three de-anodizing regimes following the first anodizing step and preceding the second one. The de-anodizing methods include electrolytic etching (EE) and chemical etching using either phosphoric acid (PE) or sodium hydroxide (HE) solutions. Three of the obtained AAO samples were black colored by electrodeposition of copper nanoparticles in their pores. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization techniques were used to characterize the electrochemical performance of the two sets of the prepared samples. In general, the data obtained in aggressive aerated 0.5 M HCl solution demonstrated dissimilar behavior for the three prepared samples despite that the second anodizing step was the same for all of them. The data indicated that the resistance and thickness of the inner barrier part of nano-PAA film, are the main controlling factors determining its stability. On the other hand, coloring the film decreased its stability due to the galvanic effect. The difference in the electrochemical behavior of the three colored samples was discussed based on the difference in both the pore size and thickness of the outer porous part of PAA film as supported by SEM, TEM and cross-sectional micrographs. These results can thus contribute for better engineering

Enzymatic pulp upgrade for producing high-value cellulose out of a Kraft paper pulp.

Science.gov (United States)

Hutterer, Christian; Kliba, Gerhard; Punz, Manuel; Fackler, Karin; Potthast, Antje

2017-07-01

The high-yield separation of polymeric parts from wood-derived lignocellulosic material is indispensable in biorefinery concepts. For the separation of cellulose and xylan from hardwood paper pulps to obtain pulps of high cellulose contents, simple alkaline extractions were found to be the most suitable technology, although having certain limitations. These are embodied by residual alkali resistant xylan incorporated in the pulp matrix. Further purification in order to produce pure cellulose with a low uniformity could be achieved selectively degrading residual xylan and depolymerizing the cellulose macromolecules by xylanase and cellulase. The latter help to adjust cellulose chain lengths for certain dissolving pulp grades while reducing the demand for ozone in subsequent TCF bleaching. Experiments applying different commercially available enzyme preparations revealed the dependency of xylanase performance on the residual xylan content in pulps being stimulated by additional cellulase usage. The action of the latter strongly depends on the cellulose allomorphy confirming the impact of the pulp morphology. Hence, the combined application of both types of enzymes offers a high potential for upgrading pulps in order to produce a pure and high-value cellulose product. Copyright © 2017 Elsevier Inc. All rights reserved.

Effect of various de-anodizing techniques on the surface stability of non-colored and colored nanoporous AAO films in acidic solution

Science.gov (United States)

Awad, Ahmed M.; Shehata, Omnia S.; Heakal, Fakiha El-Taib

2015-12-01

Anodic aluminum oxide (AAO) is well known as an important nanostructured material, and a useful template in the fabrication of nanostructures. Nanoporous anodic alumina (PAA) with high open porosity was prepared by adopting three de-anodizing regimes following the first anodizing step and preceding the second one. The de-anodizing methods include electrolytic etching (EE) and chemical etching using either phosphoric acid (PE) or sodium hydroxide (HE) solutions. Three of the obtained AAO samples were black colored by electrodeposition of copper nanoparticles in their pores. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization techniques were used to characterize the electrochemical performance of the two sets of the prepared samples. In general, the data obtained in aggressive aerated 0.5 M HCl solution demonstrated dissimilar behavior for the three prepared samples despite that the second anodizing step was the same for all of them. The data indicated that the resistance and thickness of the inner barrier part of nano-PAA film, are the main controlling factors determining its stability. On the other hand, coloring the film decreased its stability due to the galvanic effect. The difference in the electrochemical behavior of the three colored samples was discussed based on the difference in both the pore size and thickness of the outer porous part of PAA film as supported by SEM, TEM and cross-sectional micrographs. These results can thus contribute for better engineering applications of nanoporous AAO.

Quantification and analysis of color stability based on thermal transient behavior in white LED lamps.

Science.gov (United States)

Nisa Khan, M

2017-09-20

We present measurement and analysis of color stability over time for two categories of white LED lamps based on their thermal management scheme, which also affects their transient lumen depreciation. We previously reported that lumen depreciation in LED lamps can be minimized by properly designing the heat sink configuration that allows lamps to reach a thermal equilibrium condition quickly. Although it is well known that lumen depreciation degrades color stability of white light since color coordinates vary with total lumen power by definition, quantification and characterization of color shifts based on thermal transient behavior have not been previously reported in literature for LED lamps. Here we provide experimental data and analysis of transient color shifts for two categories of household LED lamps (from a total of six lamps in two categories) and demonstrate that reaching thermal equilibrium more quickly provides better stability for color rendering, color temperature, and less deviation of color coordinates from the Planckian blackbody locus line, which are all very important characterization parameters of color for white light. We report for the first time that a lamp's color degradation from the turn-on time primarily depends on thermal transient behavior of the semiconductor LED chip, which experiences a wavelength shift as well as a decrease in its dominant wavelength peak value with time, which in turn degrades the phosphor conversion. For the first time, we also provide a comprehensive quantitative analysis that differentiates color degradation due to the heat rise in GaN/GaInN LED chips and subsequently the boards these chips are mounted on-from that caused by phosphor heating in a white LED module. Finally, we briefly discuss why there are some inevitable trade-offs between omnidirectionality and color and luminous output stability in current household LED lamps and what will help eliminate these trade-offs in future lamp designs.

Plutonium inventories for stabilization and stabilized materials

Energy Technology Data Exchange (ETDEWEB)

Williams, A.K.

1996-05-01

The objective of the breakout session was to identify characteristics of materials containing plutonium, the need to stabilize these materials for storage, and plans to accomplish the stabilization activities. All current stabilization activities are driven by the Defense Nuclear Facilities Safety Board Recommendation 94-1 (May 26, 1994) and by the recently completed Plutonium ES&H Vulnerability Assessment (DOE-EH-0415). The Implementation Plan for accomplishing stabilization of plutonium-bearing residues in response to the Recommendation and the Assessment was published by DOE on February 28, 1995. This Implementation Plan (IP) commits to stabilizing problem materials within 3 years, and stabilizing all other materials within 8 years. The IP identifies approximately 20 metric tons of plutonium requiring stabilization and/or repackaging. A further breakdown shows this material to consist of 8.5 metric tons of plutonium metal and alloys, 5.5 metric tons of plutonium as oxide, and 6 metric tons of plutonium as residues. Stabilization of the metal and oxide categories containing greater than 50 weight percent plutonium is covered by DOE Standard {open_quotes}Criteria for Safe Storage of Plutonium Metals and Oxides{close_quotes} December, 1994 (DOE-STD-3013-94). This standard establishes criteria for safe storage of stabilized plutonium metals and oxides for up to 50 years. Each of the DOE sites and contractors with large plutonium inventories has either started or is preparing to start stabilization activities to meet these criteria.

Protection of oxidative hair color fading from shampoo washing by hydrophobically modified cationic polymers.

Science.gov (United States)

Zhou, Y; Foltis, L; Moore, D J; Rigoletto, R

2009-01-01

The fading of oxidative color in hair as a result of daily shampoo washing activities has become a common problem and a source of frequent complaints by consumers. The fading occurs primarily through hair dye solubility in water. One aspect of the current study investigates the physical and chemical factors that influence hair color fading during the washing process. This is accomplished by testing hair dye dissolution in water from dyed hair samples with variation of surfactant type, pH, and hair type. Furthermore, a new approach to preventing color fading is developed aiming to provide an effective barrier function for hair dye from dissolving into water. The preliminary investigation of a series of polymers with various functional groups indicates that polymers with hydrophobically modified and cationic functionalities are most effective in preventing hair dye dissolution in water. It is also evident that a synergistic effect of the polymer's hydrophobic moieties and cationic charges are important on hair color protection during shampoo washing processes. A primary example of a polymer within this category is a cationic terpolymer of vinylpyrrolidone, dimethylaminopropyl methacrylamide, and methacryloylaminopropyl lauryldimonium chloride (INCI: Polyquaternium-55). The color protection benefit of this polymer is evaluated using newly developed methodologies for evaluating hair color changes, such as hair color fading tests through multiple shampoo washes with mannequin heads and hair tresses, both derived from human hair, colorimetry, and quantitative digital image analysis. In addition, new infrared spectroscopic imaging techniques are used to detect the hair dye deposition behavior inside hair fibers both with and without the color protection treatment. Both visual and instrumental measurement results indicate that Polyquaternium-55 provides a high level of color protection when formulated in a hair color protection regimen with up to 50% color protection. This

PULP OBTAINING METHOD FOR PACKAGE PRODUCTION

Directory of Open Access Journals (Sweden)

V. V. Kuzmich

2015-01-01

Full Text Available The paper presents a new method for obtaining pulp which is used for production of cardboard, paper and package while using carbon dioxide and hydrazine hydrate and neutral-sulfite  shive cooking. Output increase of  the desired product can be explained by reduction in destruction of plant raw material carbohydrates during its cooking process. Quality improvement of the desired product (improvement in bleaching and output is attributed to the fact that usage of carbon dioxide and hydrazine contributes to provision of polysaccharide chain resistance to destruction due to the presence of  end links having structure of metasaccharinic and aldonic acids.The author has developed a new method for pulp obtaining on the basis of the executed investigations  and literature data.  СО2 and hydrazine hydrate have been used for obtaining pulp. Method invention concerns pulp obtaining and it can be used for paper and cardboard package manufacturing in pulp and paper industry.The method is to be carried in the following way: pulp-containing plant raw material is loaded into an autoclave and then aqua solution of sodium monosulfite containing hydrazine hydrate that constitutes 4–5 % of absolute dry pulp-containing raw material mass with liquid module 1:6–1:8 is supplied into the autoclave. The autoclave is closed for operation under pressure and the solution is carbonated under pressure which constitutes 5–8 % of absolute dry plant raw material (shover. Temperature is subsequently raised up to 180 °С in the space of 2 hours and cooking is carried out in the course of 4 hours. Usage of  the proposed method for shover cooking makes it possible to reduce monosulfite cooking process and improve qualitative characteristics and output of the desired product.  In addition to above mentioned fact there is a possibility to improve bleaching and final product output. 

Captopril 25 mg tablets stability assessment in different primary packing materials

Directory of Open Access Journals (Sweden)

Flávia Costa Mendes Paiva

2017-11-01

Full Text Available Introduction: Packaging is used to provide protection and information, from the production to the administration of a formulation. It is essential to define the primary packaging, for keeping the therapeutic efficacy of drugs, safety of users and for protecting drugs from instability. Objectives: The main objective of this study was to assess the stability of captopril 25 mg tablets in different primary packaging materials. Method: The characterization (IR, DSC and physical tests of the packaging materials used for captopril was carried out prior to the manufacture of tablets. Tablets were also characterized by physical-chemical analysis, comparative dissolution profile and stability studies. Results: The characterization of packaging materials was crucial for understanding the behavior of captopril when packed in each material. Materials with significant barrier, as blisters PVC/PVdC 90 g.m-² and hard aluminum and PVC/PE/PVdC and hard aluminum showed satisfactory results in a second stage, S2. On the contrary, lower barrier materials as blisters PVC/PVdC 40 g.m-² and hard aluminum did not present dissolution analysis S2. Conclusions: The aluminum strip presented the best results. And the batch in glass bottle, although packaged in excellent material, was disapproved in accelerated stability.

The performance of human dental pulp stem cells on different three-dimensional scaffold materials.

NARCIS (Netherlands)

Zhang, W.; Walboomers, X.F.; Kuppevelt, A.H.M.S.M. van; Daamen, W.F.; Bian, Z.; Jansen, J.A.

2006-01-01

The aim of this study was to investigate the in vitro and in vivo behavior of human dental pulp stem cells (DPSCs) isolated from impacted third molars, when seeded onto different 3-dimensional (3-D) scaffold materials: i.e. a spongeous collagen, a porous ceramic, and a fibrous titanium mesh.

Color of bulk-fill composite resin restorative materials.

Science.gov (United States)

Barutcigil, Çağatay; Barutcigil, Kubilay; Özarslan, Mehmet Mustafa; Dündar, Ayşe; Yilmaz, Burak

2018-03-01

To evaluate the color stability of novel bulk-fill composite resins. Color measurements of a nanohybrid composite resin (Z550) and 3 bulk-fill composite resins (BLK, AFX, XTF; n = 45) were performed before polymerization. After polymerization, color measurements were repeated and specimens were immersed in distilled water or red wine, or coffee. Color change [CIEDE2000 (ΔE 00 )] was calculated after 24 h, 1 and 3 weeks. Data were analyzed with Kruskal-Wallis, Mann-Whitney U and Wilcoxon tests (α = 0.05). Color changes observed after polymerization were significant for all groups. Color changes observed in distilled water for Z550 and AFX were significant. Color changes after stored in red wine and coffee were significant for all groups. Bulk-fill composite resin color change increased over time for all groups in red wine and coffee (P composite resin and bulk-fill composite resins. AFX had the highest color change in distilled water. The color of tested bulk-fill composite resins significantly changed after immersion in beverages and over time. Color change observed with the nanohybrid composite resin after 1 week was stable. Clinicians should keep in mind that tested composite resins may change color when exposed to water and significantly change color immediately after they are polymerized. In addition, the color change continues over time should the patient is a coffee and/or red wine consumer. © 2017 Wiley Periodicals, Inc.

Comparative pulping of sunflower stalks

Directory of Open Access Journals (Sweden)

Valerii Barbash

2016-03-01

Full Text Available The procedure of holocellulose content determination in non-wood plant raw materials was developed. The strength properties of pulp obtained from sunflower stalks by neutral-sulphite, soda, alkaline sulphite-anthraquinone-ethanol and peracetic methods of delignification were studied. Methodology of comparison of plant materials delignification methods using new lignin-carbohydrate diagram was proposed. It was shown, that the alkaline sulphite-anthraquinone-ethanol method of pulping is characterized by the highest delignification degree and is the most efficient among the studied methods

Low Temperature Soda-Oxygen Pulping of Bagasse.

Science.gov (United States)

Yue, Fengxia; Chen, Ke-Li; Lu, Fachuang

2016-01-13

Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today's pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum cooking temperature 100 °C, time hold at maximum temperature 180 min, initial pressure of oxygen 0.6 MPa, MgSO4 charge 0.5%, and de-pithed bagasse consistency 12%. Properties of the resultant pulp were screened yield 60.9%, Kappa number 14, viscosity 766 dm³/kg, and brightness 63.7% ISO. Similar pulps were also obtained at 110 °C or 105 °C with a cooking time of 90 min. Compared with pulps obtained at higher temperatures (115-125 °C), this pulp had higher screened yield, brightness, and acceptable viscosity, while the delignification degree was moderate. These results indicated that soda-oxygen pulping at 100 °C, the lowest cooking temperature reported so far for soda-oxygen pulping, is a suitable process for making chemical pulp from bagasse. Pulping at lower temperature and using oxygen make it an environmental friendly and energy-saving pulping process.

Low Temperature Soda-Oxygen Pulping of Bagasse

Directory of Open Access Journals (Sweden)

Fengxia Yue

2016-01-01

Full Text Available Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today’s pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum cooking temperature 100 °C, time hold at maximum temperature 180 min, initial pressure of oxygen 0.6 MPa, MgSO4 charge 0.5%, and de-pithed bagasse consistency 12%. Properties of the resultant pulp were screened yield 60.9%, Kappa number 14, viscosity 766 dm3/kg, and brightness 63.7% ISO. Similar pulps were also obtained at 110 °C or 105 °C with a cooking time of 90 min. Compared with pulps obtained at higher temperatures (115–125 °C, this pulp had higher screened yield, brightness, and acceptable viscosity, while the delignification degree was moderate. These results indicated that soda-oxygen pulping at 100 °C, the lowest cooking temperature reported so far for soda-oxygen pulping, is a suitable process for making chemical pulp from bagasse. Pulping at lower temperature and using oxygen make it an environmental friendly and energy-saving pulping process.

Effect of opacifiers and UV absorbers on pigmented maxillofacial silicone elastomer, part 1: color stability after artificial aging.

Science.gov (United States)

Han, Ying; Powers, John M; Kiat-Amnuay, Sudarat

2013-06-01

Much dissatisfaction with the color instability and reduced lifetime of extraoral maxillofacial prostheses due to degradation has been reported. The purpose of this study was to compare the effect of a UV mineral-based light protecting agent (LP) on the color stability of pigmented maxillofacial silicone elastomer MDX-4210/Type A after artificial aging to 2 widely used opacifiers. Forty-five groups were established (n=225 total). Three different types of opacifiers (LP, titanium white dry pigment [TW], or silicone intrinsic white [SW]) were added to silicone MDX-4210/type A at 3 concentrations (5%, 10%, or 15%) and subsequently combined with each of 5 colors (no pigments [control], red, blue, yellow, or mixed pigments). Artists' oil pigment was used with LP and TW, while intrinsic silicone pigment was used to color SW. Before and after an energy exposure of 450 kJ/m(2), CIE L*a*b* values were measured with a spectrophotometer. The CIELAB 50:50% perceptibility (ΔE*=1.1) and acceptability threshold (ΔE*=3.0) were used to interpret color changes (ΔE*). Color differences after aging were subjected to 3-way ANOVA. Means were compared by the Fisher PLSD intervals at α=.05. The ΔE* values of all groups were below the acceptability threshold of ΔE*=3.0, except for the control group of SW at 10%, which showed the greatest color change (ΔE*=3.1). When mixed pigment groups were considered, at 5% concentration, LP showed the smallest color change, followed by SW and TW (P.05); at 15%, LP showed the smallest color change, followed by TW and SW (P<.05). All 3 opacifiers at all concentrations protected pigmented silicone MDX4-4210/Type A from color degradation. The LP group showed the smallest color changes. Copyright © 2013 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

RE-UTILIZATION OF INORGANIC SOLID WASTE (LIME MUD AS FOREST ROAD STABILIZER FROM THE CHEMICAL RECOVERY PROCESS IN KRAFT PULP MILL

Directory of Open Access Journals (Sweden)

Habip Eroğlu

2005-04-01

Full Text Available Waste handling is a concern in all pulp and paper mills. Best available techniques for reducing waste is to minimize the generation of solid waste and/or reuse these materials, wherever practicable. One of the most important solid wastes is lime mud which is generated from the kraft pulping in its chemical recovery process. This paper explores the composition of lime mud resulting from the chemical recovery unite of kraft pulp mill and investigation of this waste for re-using beneficially on sub grade and pavement of forest road as a alternative disposal method. Lime mud obtained from the re-causticising process in SEKA pulp mill that utilizes wheat straw and reed as the principal raw material was supplied with % 47 water content and its chemical and physical characterisations was performed according to standard methods. Dried waste to environmental condition was mixed with certain amount to composite cement for using on pavement and sandy clay, loamy clay and clay soils for enriching forest road sub grade properties. In order to investigate the lime mud addition on pavement and sub grade properties necessary physical tests were performed. As a consequence this study reveals that while waste of lime mud causes environmental and economical problem with conventional disposal techniques and/or abandoning to environment, this waste can be used as good stabilisation materials on forest road sub-grade and pavement without any environmental problem.

Color in the corners: ITO-free white OLEDs with angular color stability.

Science.gov (United States)

Gaynor, Whitney; Hofmann, Simone; Christoforo, M Greyson; Sachse, Christoph; Mehra, Saahil; Salleo, Alberto; McGehee, Michael D; Gather, Malte C; Lüssem, Björn; Müller-Meskamp, Lars; Peumans, Peter; Leo, Karl

2013-08-07

High-efficiency white OLEDs fabricated on silver nanowire-based composite transparent electrodes show almost perfectly Lambertian emission and superior angular color stability, imparted by electrode light scattering. The OLED efficiencies are comparable to those fabricated using indium tin oxide. The transparent electrodes are fully solution-processable, thin-film compatible, and have a figure of merit suitable for large-area devices. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of a surface sealant on the color stability of composite resins after immersion in staining solution.

Science.gov (United States)

Pedroso, Lauana Borges; Barreto, Luma Franciélle Cabreira; Miotti, Leonardo Lamberti; Nicoloso, Gabriel Ferreira; Durand, Leticia Brandão

2016-01-01

This study evaluated the influence of surface sealants on the color stability of 2 different composite resins after immersion in coffee. Four groups were created (n = 10): microhybrid composite, microhybrid with surface sealant, nanofilled composite, and nanofilled composite with surface sealant. Half of the specimens of each group were immersed in distilled water and half were immersed in coffee for 48 hours. Color was measured before and after immersion. Groups with surface sealants presented less color variation when compared with the groups without surface sealants. The nanofilled resin specimens presented the greatest color variation within the groups without sealant. The surface sealant positively influenced the color stability of composite resin specimens immersed in coffee. When surface sealant was not applied, the microhybrid specimens had better color stability than the nanofilled.

Physicochemical characteristics of the coconut pulp (Acrocomia aculeata) for use as support of proteins and metal material

Energy Technology Data Exchange (ETDEWEB)

Yubero, F.; Ayala, J.; Lopez, M.; Valdovinos, V.; Monteiro, M.; Gonzalez, Y., E-mail: fyubero@qui.una.py [National University of Asunción (Paraguay); Thompson, W. [Universidade Estadual de Londrina (UEL), PR (Brazil). Departamento de Fisica; Arguello, J. [Universidade Federal do Rio Grande do Sul (UFRGS), RS (Brazil). Instituto de Quimica

2016-07-01

The fruit of the Acrocomia aculeata, native palm tree typical of the tropical region, is exploited mainly for the manufacture of oils and animal consumption. This study was aimed to determine the physicochemical characteristics of the residue of the Acrocomia aculeata coconut pulp in order to apply it in the development of new materials. Therefore fruits collected for the production of pulp were drying and pulverized, the chemical and mineral compositions were studied by GAFTA standardized techniques for the analysis of crude fiber, protein, fat and calories and INAA respectively. Subsequently, the initial material was chemically modified and assessed the solubilities of the native material and the obtained modified material proving to be completely insoluble in solvents organic and aqueous (water, ethanol, terbutanol, isobutanol and hexane), the materials were analyzed by IR with Transformed Fourier and the results showed the existence of changes in the double link lengthening conjugated and aromatic; and link double nitrogen C=N/N=O. EPR analysis indicated that the materials obtained are not paramagnetic at room temperature, however can incorporate magnetite and Fe{sup 0}. These preliminary studies concluded that this eco material could be applied as support of proteins and metals. (author)

Physicochemical characteristics of the coconut pulp (Acrocomia aculeata) for use as support of proteins and metal material

International Nuclear Information System (INIS)

Yubero, F.; Ayala, J.; Lopez, M.; Valdovinos, V.; Monteiro, M.; Gonzalez, Y.; Thompson, W.; Arguello, J.

2016-01-01

The fruit of the Acrocomia aculeata, native palm tree typical of the tropical region, is exploited mainly for the manufacture of oils and animal consumption. This study was aimed to determine the physicochemical characteristics of the residue of the Acrocomia aculeata coconut pulp in order to apply it in the development of new materials. Therefore fruits collected for the production of pulp were drying and pulverized, the chemical and mineral compositions were studied by GAFTA standardized techniques for the analysis of crude fiber, protein, fat and calories and INAA respectively. Subsequently, the initial material was chemically modified and assessed the solubilities of the native material and the obtained modified material proving to be completely insoluble in solvents organic and aqueous (water, ethanol, terbutanol, isobutanol and hexane), the materials were analyzed by IR with Transformed Fourier and the results showed the existence of changes in the double link lengthening conjugated and aromatic; and link double nitrogen C=N/N=O. EPR analysis indicated that the materials obtained are not paramagnetic at room temperature, however can incorporate magnetite and Fe 0 . These preliminary studies concluded that this eco material could be applied as support of proteins and metals. (author)

CHEMICAL COMPOSITION, CRYSTALLINITY, AND THERMAL DEGRADATION OF BLEACHED AND UNBLEACHED KENAF BAST (Hibiscus cannabinus PULP AND NANOFIBERS

Directory of Open Access Journals (Sweden)

Mehdi Jonoobi

2009-05-01

Full Text Available Kenaf (Hibiscus cannabinus nanofibers were isolated from unbleached and bleached pulp by a combination of chemical and mechanical treatments. The chemical methods were based on NaOH-AQ (anthraquinone and three-stage bleaching (DEpD processes, whereas the mechanical techniques involved refining, cryo-crushing, and high-pressure homogenization. The size and morphology of the obtained fibers were characterized by environmental scanning electron microscopy (ESEM and transmission electron microscopy (TEM, and the studies showed that the isolated nanofibers from unbleached and bleached pulp had diameters between 10-90 nm, while their length was in the micrometer range. Fourier transform infrared (FTIR spectroscopy demonstrated that the content of lignin and hemicellulose decreased in the pulping process and that lignin was almost completely removed during bleaching. Moreover, thermogravimetric analysis (TGA indicated that both pulp types as well as the nanofibers displayed a superior thermal stability as compared to the raw kenaf. Finally, X-ray analyses showed that the chemo-mechanical treatments altered the crystallinity of the pulp and the nanofibers: the bleached pulp had a higher crystallinity than its unbleached counterpart, and the bleached nanofibers presented the highest crystallinity of all the investigated materials.

Characterization of solid wastes from kraft pulp industry for ceramic materials development purposes

International Nuclear Information System (INIS)

Rodrigues, L.R.; Francisco, M.A.C.O.; Sagrillo, V.P.D.; Louzada, D.M.; Entringer, J.M.S.

2016-01-01

The Kraft pulp industry generates a large amount of solid wastes. Due this large quantity, the target of this study is characterize inorganic solid wastes, dregs, grits and lime mud, from the step of reagents recovery of Kraft process, aiming evaluate the potentiality of their use as alternative raw material on development of ceramic materials. Initially, the wastes were dried and ground, then they were subjected to the following characterization techniques: pH analysis, particle size analysis, X ray fluorescence, X ray diffraction, differential thermal analysis and thermogravimetric analysis and scanning electron microscopy. According to the results, it may be concluded that these wastes could be used as raw material in production of red ceramic and luting materials. (author)

The Biomineralization of a Bioactive Glass-Incorporated Light-Curable Pulp Capping Material Using Human Dental Pulp Stem Cells

Directory of Open Access Journals (Sweden)

Soo-Kyung Jun

2017-01-01

Full Text Available The aim of this study was to investigate the biomineralization of a newly introduced bioactive glass-incorporated light-curable pulp capping material using human dental pulp stem cells (hDPSCs. The product (Bioactive® [BA] was compared with a conventional calcium hydroxide-incorporated (Dycal [DC] and a light-curable (Theracal® [TC] counterpart. Eluates from set specimens were used for investigating the cytotoxicity and biomineralization ability, determined by alkaline phosphatase (ALP activity and alizarin red staining (ARS. Cations and hydroxide ions in the extracts were measured. An hDPSC viability of less than 70% was observed with 50% diluted extract in all groups and with 25% diluted extract in the DC. Culturing with 12.5% diluted BA extract statistically lowered ALP activity and biomineralization compared to DC (p0.05. Ca (~110 ppm and hydroxide ions (pH 11 were only detected in DC and TC. Ionic supplement-added BA, which contained similar ion concentrations as TC, showed similar ARS mineralization compared to TC. In conclusion, the BA was similar to, yet more cytotoxic to hDPSCs than, its DC and TC. The BA was considered to stimulate biomineralization similar to DC and TC only when it released a similar amount of Ca and hydroxide ions.

The relationship between pulp calcifications and salivary gland calcifications

OpenAIRE

Kaswan, Sumita; Patil, Santosh; Maheshwari, Sneha; Rahman, Farzan; Khandelwal, Suneet

2014-01-01

Aim: Pulp stones are discrete calcified bodies found in the dental pulp. Sialolithasis is the most common salivary gland disease. The aim of the present study was to determine the relationship between the pulp stones and salivary gland stones. Material and Methods: 196 patients were randomly selected from the out patient department for the study. The periapical radiographs for all patients were evaluated for the presence or absence of the narrowing of dental pulp chambers and pulp canals. The...

Eucalyptus kraft pulp production: Thermogravimetry monitoring

International Nuclear Information System (INIS)

Barneto, Agustin G.; Vila, Carlos; Ariza, Jose

2011-01-01

Highlights: → Thermogravimetric analysis can be used to monitor the pulping process in a pulp mill. → ECF bleaching process affects the crystalline cellulose volatilization. → The fibre size has an influence on composition and thermal behavior of pulp. - Abstract: Under oxidative environment the thermal degradation of lignocellulosic materials like wood or pulp is sensitive to slight composition changes. For this, in order to complement the chemical and X-ray diffraction results, thermogravimetric analyses (TGA) were used to monitor pulp production in a modern pulp mill. Runs were carried out on crude, oxygen delignified and bleached pulps from three eucalyptus woods from different species and geographical origins. Moreover, with the modeling of thermogravimetric data, it was possible to obtain an approximate composition of samples which includes crystalline and amorphous cellulose. TGA results show that pulping has an intensive effect on bulk lignin and hemicellulose, but it has limited influence on the removal of these substances when they are linked to cellulose microfibril. The stages of oxygen delignification and bleaching, based in chlorine dioxide and hydrogen peroxide, increase the crystalline cellulose volatilization rate. These changes are compatible with a more crystalline microfibril. The influence of the fibre size on pulp composition, crystallinity and thermal degradation behavior was observed.

Color stability of microfilled, microhybrid and nanocomposite resins--an in vitro study.

Science.gov (United States)

Nasim, Iffat; Neelakantan, Prasanna; Sujeer, R; Subbarao, C V

2010-01-01

The aim of this study was to evaluate the effect of two beverages-Tea and Pepsi on the color stability of three different composite resins after a period of 7 and 30 days. Color stability of a microfilled, microhybrid and nanocomposite was evaluated after storage in Tea, a carbonated drink or Distilled Water for 7 and 30 days. Color measurement was done using reflectance spectrophotometer based on the CIE L*a*b* color scale. Mean values of the different groups were compared using three-way analysis of variance and multiple comparisons of the mean values were done using Tukey-Kramer test with 0.05 as significance level. All tested resin composites showed color change after a period of 7 and 30 days. The color change exhibited by all three groups was significantly different for all three beverages studied, at both time periods (pPepsi at the 7th and 30th day. The nanocomposite discolored most in Tea at 7th and 30th day. All efforts should be made to minimize discoloration of composite restorations by adopting excellent polishing techniques. Patients should also be educated on the possibility of the restoration to undergo staining under the influence of beverages. Copyright © 2010 Elsevier Ltd. All rights reserved.

Effect of finishing and polishing on the color stability of a composite resin immersed in staining solutions

Directory of Open Access Journals (Sweden)

Maiara Justo Polli

2015-01-01

Full Text Available Objective: To evaluate the influence of finishing/polishing methods and staining solutions using different immersion periods on the color stability of a microhybrid composite resin. Materials and Methods: Ninety specimens were fabricated using a stainless steel mold and polyester strips. The samples were randomly divided into five groups according to the finishing and polishing performed: Control group (no surface treatment was performed, Diamond Pro group, Diamond burs group, Enhance group, and SiC paper group. After finishing and polishing, six samples from each group were immersed in coffee, red wine, or water for 30 days. The color measurements were obtained using digital photography before immersion and after 7, 15, and 30 days of immersion. The red, green, and blue values provided by the Adobe Photoshop software were converted into CIELab values. A three-way analysis of variance and Tukey's test were used for statistical analysis (P ≤ 0.05. Results: The finishing and polishing methods, staining solutions, immersion times, and their interaction had statistically significant effects on the color change (P = 0.00. Coffee and red wine caused intense staining. Among the polishing methods, the highest color change value was observed in the control group (P < 0.05 and the Diamond Pro disks provided the most stain-resistant surfaces (P ≤ 0.05. Conclusion: The finishing and polishing method, staining solution, and immersion time influences the color stability. Finishing and polishing should be applied to obtain a more stain-resistant surface.

THE EFFECT OF MOUTH RINSES ON THE COLOR STABILITY OF SONICFILL AND A NANOHYBRID COMPOSITE

Directory of Open Access Journals (Sweden)

Tuğba Toz-Akalın

2016-04-01

Full Text Available Purpose: The aim of this study was to evaluate the effects of 4 mouth rinses on the color stability of two different resin composites. Materials and Methods: A2 shade sonic-activated bulk fill material SonicFill (Kerr and conventional nanohybrid composite Filtek Z550 (3M ESPE were used. Forty disc-shaped specimens (10 mm x 2 mm were fabricated for both composites and finished using 400-grit SiC paper and polished. After polishing and immersing in distilled water for 24h all specimens were subjected to color measurements. The baseline color values (L*, a*, b* of each specimen were measured with a colorimeter. Following baseline measurement each composite group was divided into 5 groups: Oral-B Pro Expert Clinic Line Alcoholfree (Oral-B group, Listerine Tooth Defense Rinse (Listerine group, Pharmol Zn Mouth rinse (Çözümilaç group, Nilera Mouth rinse (Nilera group and Distilled water (control group. The specimens were incubated in mouth rinses (20 ml at 37°C for 12 hours and subjected to color measurement. Two-way ANO VA was used for statistical analysis (p<0.05. Results: SonicFill showed significantly higher discoloration when exposed to Oral-B Pro Expert Clinic Line Alcohol-free, Listerine Tooth Defense Rinse and Pharmol Zn Mouth rinse. The color differences of two resin composites were not statistically significant for distilled water and Nilera Mouth rinse. Conclusion: Within the limits of this study it can be concluded that the SonicFill showed higher discoloration than nanohybrid resin composite Filtek Z550.

Towards muscle-specific meat color stability of Chinese Luxi yellow cattle: A proteomic insight into post-mortem storage.

Science.gov (United States)

Wu, Wei; Yu, Qian-Qian; Fu, Yu; Tian, Xiao-Jing; Jia, Fei; Li, Xing-Min; Dai, Rui-Tong

2016-09-16

Searching for potential predictors of meat color is a challenging task for the meat industry. In this study, the relationship between meat color parameters and the sarcoplasmic proteome of M. longissimuss lumborum (LL) and M. psoas major (PM) from Chinese Luxi yellow cattle during post-mortem storage (0, 5, 10 and 15days) were explored with the aid of the integrated proteomics and bioinformatics approaches. Meat color attributes revealed that LL displayed better color stability than PM during storage. Furthermore, sarcoplasmic proteins of these two muscles were compared between days 5, 10, 15 and day 0. Several proteins were closely correlated with meat color attributes and they were muscle-specific and responsible for the meat color stability at different storage periods. Glycerol-3-phosphate dehydrogenase, fructose-bisphosphate aldolase A isoform, glycogen phosphorylase, peroxiredoxin-2, phosphoglucomutase-1, superoxide dismutase [Cu-Zn], heat shock cognate protein (71kDa) might serve as the candidate predictors of meat color stability during post-mortem storage. In addition, bioinformatics analyses indicated that more proteins were involved in glycolytic metabolism of LL, which contributed to better meat color stability of LL than PM. The present results could provide a proteomic insight into muscle-specific meat color stability of Chinese Luxi yellow cattle during post-mortem storage. Copyright © 2015 Elsevier B.V. All rights reserved.

Estabilidade química, físico-química e microbiológica de polpas de acerola pasteurizadas e não-pasteurizadas de cultivo orgânico Chemical, physicochemical and microbiological stability of pasteurized and non pasteurized acerola pulps from organic cultivation

Directory of Open Access Journals (Sweden)

Rafaela Maria Temóteo Lima

2012-02-01

Full Text Available O presente trabalho objetivou avaliar a estabilidade química, físico-química e microbiológica de polpas de acerola pasteurizadas e não-pasteurizadas, oriundas de cultivo orgânico e armazenadas sob congelamento (-18±2°C durante 360 dias. O armazenamento sob congelamento não ocasionou perdas significativas de qualidade das polpas de acerola. No entanto, o tratamento térmico influenciou negativamente nos conteúdos iniciais de alguns componentes, principalmente sólidos solúveis, açúcares solúveis totais e redutores, que apresentaram conteúdos inferiores no início do armazenamento para as polpas pasteurizadas. As polpas pasteurizadas e não-pasteurizadas apresentaram boa qualidade microbiológica do início ao final do armazenamento. Dentre as polpas estudadas, as polpas não-pasteurizadas apresentaram melhores características iniciais de cor. As polpas pasteurizadas garantiram melhores características microbiológicas no que concerne aos aspectos de segurança alimentar.The present research aimed to evaluate the chemical, physical-chemical and microbiological stability of pasteurized and non-pasteurized acerola pulp coming from organic cultivation stored frozen for 360 days. Storage under freezing did not cause significant loss of acerola pulp's quality. However, the heat treatment had a negative influence on the initial contents of some components, especially soluble solids, total soluble and reducing sugars, which showed lower contents at the beginning of storage for pasteurized pulp. Among the pulps studied, non-pasteurized pulps showed the best characteristics of the initial color. The pasteurized pulps guaranteed best features in regard to the microbiological aspects of food safety.

Kinetic modeling of formic acid pulping of bagasse.

Science.gov (United States)

Tu, Qiliang; Fu, Shiyu; Zhan, Huaiyu; Chai, Xinsheng; Lucia, Lucian A

2008-05-14

Organic solvent or organosolv pulping processes are alternatives to soda or kraft pulping to delignify lignocellulosic materials for the production of paper pulp. Formic acid, a typical organosolv system, has been presently examined under atmospheric pressure to pulp bagasse fibers. It was shown that efficient bagasse pulping was achieved when the formic acid concentration was limited to 90% (v/v). A statistical kinetic model based on the experimental results for the delignification of bagasse during formic acid pulping was developed that can be described as follows: D (delignification) = 0.747 x C(formicacid) (1.688) x (1 - e(-0.05171t)), an equation that can be used to predict the lignin content in formic acid during the pulping process. The delignification of bagasse by 90% formic acid was almost completed after approximately 80 min, while extended pulping did not improve the delignification but tended to degrade the carbohydrates in bagasse, especially the hemicelluloses, which were rapidly hydrolyzed at the onset of pulping.

Rice straw pulp obtained by using various methods.

Science.gov (United States)

Rodríguez, Alejandro; Moral, Ana; Serrano, Luis; Labidi, Jalel; Jiménez, Luis

2008-05-01

Rice straw was used as an alternative raw material to obtain cellulosics pulps. Pulping was done by using classics reagents as soda (with anthraquinone and parabenzoquinone as aditives), potassium hydroxide and Kraft process. The holocellulose, alpha-cellulose and lignin contents of rice straw (viz. 60.7, 41.2 and 21.9 wt%, respectively) are similar to those of some woody raw materials such as pine and eucalyptus, and various non-wood materials including olive tree prunings, wheat straw and sunflower stalks. Pulping tests were conducted by using soda, soda and anthraquinone at 1 wt%, soda and parabenzoquinone at 1 wt%, potassium hydroxide and sodium sulphate (Kraft process) under two different sets of operating conditions, namely: (a) a 10 wt% reagent concentration, 170 degrees C and 60 min; and (b) 15 wt% reagent, 180 degrees C and 90 min. The solid/liquid ratio was 6 in both cases. Paper sheets made from pulp extracted by cooking with soda (15 wt%) and AQ (1 wt%) at 180 degrees C and 90 min pulp exhibit the best drainage index, breaking length, stretch and burst index (viz. 23 degrees SR, 3494 m, 3.34% and 2.51 kN/g, respectively).

Performance of a Horizontal Triple Cylinder Type Pulping Machine

Directory of Open Access Journals (Sweden)

Sukrisno Widyotomo

2011-05-01

Full Text Available Pulping is one important step in wet coffee processing method. Pulping process usually uses a machine which constructed by wood or metal materials. A horizontal single cylinder type of fresh coffee cherries pulping machine is the most popular machine in coffee processing. One of the weaknesses of a horizontal single cylinder type of fresh coffee cherries pulping machine is higher in broken beans. Broken bean is one of mayor aspects in defect system that contribute to low quality. Indonesian Coffee and Cocoa Research Institute has designed and tested a horizontal double cylinder type of fresh coffee cherries pulping machine which resulted in 12.6—21.4% of broken beans. To reduce percentage of broken beans, Indonesian Coffee and Cocoa Research Institute has developed and tested a horizontal triple cylinder type of fresh coffee cherries pulping machine. Material tested was fresh mature Robusta coffee cherries, 60—65% (wet basis moisture content; has classified on 3 levels i.e. unsorted, small and medium, and clean from metal and foreign materials. The result showed that the machine produced 6,340 kg/h in optimal capacity for operational conditions, 1400 rpm rotor rotation speed for unsorted coffee cherries with composition 55.5% whole parchment coffee, 3.66% broken beans, and 1% beans in wet skin.Key words : coffee, pulp, pulper, cylinder, quality.

MASSAHAKE whole tree harvesting method for pulp raw-material and fuel -- R&D in 1993--1998

Energy Technology Data Exchange (ETDEWEB)

Asplund, D.A.; Ahonen, M.A. [Technical Research Centre of Finland, Jyvaeskylae (Finland)

1993-12-31

In Finland biofuels and hydropower are the only indigenous fuels available. Peat, wood and wood derived fuels form about 18% of total primary energy requirement. The largest wood and wood fuel user in Finland is wood processing industry, paper, pulp, sawmills. Due to silvicultural activities the growth of forests has developed an instant need for first thinnings. This need is about 12% of total stem wood growth. With conventional harvesting methods this would produce about 8 mill. m{sup 3} pulp raw material and 2 mill. m{sup 3} wood fuel. By using integrated harvesting methods about 12 mill. m{sup 3} pulp raw material and 8 mill. m{sup 3} (about 1, 3 mill. toe) fuel could be produced. At the moment, there is no economically profitable method for harvesting first thinning trees for industrial use or energy production. Hence, there are a few ongoing research projects aiming at solving the question of integrated harvesting. MASSAHAKE chip purification method has been under R&D since 1987. Research with continuous experimental line (capacity 5--10 loose-m{sup 3}) has been done in 1991 and 1992. The research has concentrated on pine whole tree chip treatment, but preliminary tests with birch whole tree chips has been done. The experiment line will be modified for birth whole tree chips during 1993. Based on the research results more than 60% of the whole tree chips can be separated to pulp raw material with < 1% bark content. This amount is 1.5--2 times more than with present technology. The yield of fuel fraction is 2--4 times higher compared to present methods. Fuel fraction is homogeneous and could be used in most furnaces for energy production. By replacing fossil fuels with wood fuel in energy production it is possible to reduce CO{sub 2}-emissions significantly. This paper presents the wood fuel research areas in Finland and technical potential of MASSAHAKE-method including the plant for building a demonstration plant based on this technology.

Influence of mitochondrial efficiency on beef lean color stability

Science.gov (United States)

Loss of electrons in the electron transport chain has been implicated as a source of variation in feed efficiency of meat producing animals. The present study was conducted to evaluate the effects of electron loss during electron transport on beef lean color stability. Beef carcasses (n = 91) were...

Organo mercurials in pulp and paper industry

Energy Technology Data Exchange (ETDEWEB)

Bouveng, H O

1967-01-01

Today phenyl mercury acetate (PMA) is used in the paper and pulp industry for two purposes: slime control in paper machine systems and impregnation of wet mechanical pulp. PMA is a commonly used slimicide. It is used for slime control in such a way that a minor part (5-20% depending on mill operation) will reach the watercourse with the waste water and contaminate aquatic life. PMA used for impregnation concerns wet mechanical pulp produced for export as raw material, mostly for newsprint. Treatment of this pulp with PMA is necessary to avoid changes caused by molds and rot fungi.

Development and stability studies of sunscreen cream formulations containing three photo-protective filters

Directory of Open Access Journals (Sweden)

Slim Smaoui

2017-02-01

Full Text Available The present study aimed to formulate and subsequently evaluate sunscreen cream (W/O/W emulsion containing three photo-protective filters: benzophenone-3, ethylhexyl methoxycinnamate and titanium dioxide at different percentages. Formulations were stored at 8, 25 and 40 °C for four weeks to investigate their stability. Color, centrifugation, liquefaction, phase separation, pH and Sun Protection Factor (SPF of sunscreen cream formulations were determined. The microbiological stability of the creams was also evaluated and the organoleptic quality was carried out for 28 days. Interestingly, the combination of 7% Benzophenone-3, 7% Ethylhexyl methoxycinnamate and 6% Titanium dioxide preserved physicochemical properties of the product and was efficient against the development of different spoilage microorganisms as well as aerobic plate counts, Pseudomonas aeruginosa, Staphylococcus aureus, and yeast and mold counts. Furthermore, a good stability was observed for all formulations throughout the experimental period. The newly formulated sunscreen cream was proved to exhibit a number of promising properties and attributes that might open new opportunities for the development of more efficient, safe, and cost-effective skin-care, cosmetic, and pharmaceutical products.

Influence of whitening and regular dentifrices on orthodontic clear ligature color stability.

Science.gov (United States)

Oliveira, Adauê S; Kaizer, Marina R; Salgado, Vinícius E; Soldati, Dener C; Silva, Roberta C; Moraes, Rafael R

2015-01-01

This study evaluated the effect of brushing orthodontic clear ligatures with a whitening dentifrice containing a blue pigment (Close Up White Now, Unilever, London, UK) on their color stability, when exposed to a staining agent. Ligatures from 3M Unitek (Monrovia, CA, USA) and Morelli (Sorocaba, SP, Brazil) were tested. Baseline color measurements were performed and nonstained groups (control) were stored in distilled water whereas test groups were exposed for 1 hour daily to red wine. Specimens were brushed daily using regular or whitening dentifrice. Color measurements were repeated after 7, 14, 21, and 28 days using a spectrophotometer based on the CIE L*a*b* system. Decreased luminosity (CIE L*), increased red discoloration (CIE a* axis), and increased yellow discoloration (CIE b* axis) were generally observed for ligatures exposed to the staining agent. Color variation was generally lower in specimens brushed with regular dentifrice, but ligatures brushed with whitening dentifrice were generally less red and less yellow than regular dentifrice. The whitening dentifrice led to blue discoloration trend, with visually detectable differences particularly apparent according to storage condition and ligature brand. The whitening dentifrice containing blue pigment did not improve the ligature color stability, but it decreased yellow discoloration and increased a blue coloration. The use of a whitening dentifrice containing blue pigment during orthodontic treatment might decrease the yellow discoloration of elastic ligatures. © 2015 Wiley Periodicals, Inc.

Color stability and flexural strength of poly (methyl methacrylate) and bis-acrylic composite based provisional crown and bridge auto-polymerizing resins exposed to beverages and food dye: an in vitro study.

Science.gov (United States)

Gujjari, Anil K; Bhatnagar, Vishrut M; Basavaraju, Ravi M

2013-01-01

To evaluate the color stability and flexural strength of poly (methyl methacrylate) (PMMA) and bis-acrylic composite based provisional crown and bridge auto-polymerizing resins exposed to tea, coffee, cola, and food dye. Two provisional crown and bridge resins, one DPI self-cure tooth molding powder (PMMA) (Group A), and one Protemp 4 Temporization Material (bis-acrylic composite) (Group B) were used. Disk-shaped specimens for color stability testing (n = 30 for each material) and bar-shaped specimens for flexural strength testing (n = 30 for each material) were fabricated using a metal mold. The specimens were immersed in artificial saliva, artificial saliva + tea, artificial saliva + coffee, artificial saliva + cola, and artificial saliva + food dye solutions and stored in an incubator at 37°C. Color measurements were taken before immersion, and then after 3 and 7 days of immersion. Flexural strength was evaluated after 7 days of immersion. Group A showed significantly higher color stability as compared to Group B, and artificial saliva + coffee solution had the most staining capacity for the resins. Test solutions had no effect on the flexural strength of Group A, but Group B specimens immersed in artificial saliva + cola showed significantly lower flexural strength values as compared to the control group. The findings of the study showed that for materials used in the study, PMMA was more color stable than bis-acrylic composite based resin. Also, material based on PMMA was more resistant to damage from dietary beverages as compared to bis-acrylic composite based provisional crown and bridge resin.

Sisal organosolv pulp as reinforcement for cement based composites

OpenAIRE

Joaquim, Ana Paula; Tonoli, Gustavo Henrique Denzin; Santos, Sérgio Francisco Dos; Savastano Junior, Holmer

2009-01-01

The present work describes non-conventional sisal (Agave sisalana) chemical (organosolv) pulp from residues of cordage as reinforcement to cement based materials. Sisal organosolv pulp was produced in a 1:1 ethanol/water mixture and post chemically and physically characterized in order to compare its properties with sisal kraft pulp. Cement based composites reinforced with organosolv or kraft pulps and combined with polypropylene (PP) fibres were produced by the slurry de-watering and pressin...

Influence of finishing/polishing on color stability and surface roughness of composites submitted to accelerated artificial aging

Directory of Open Access Journals (Sweden)

Gustavo Da Col dos Santos Pinto

2013-01-01

Full Text Available Aim: To assess the influence of finishing/polishing procedure on color stability (ΔE and surface roughness (Ra of composites (Heliomolar and Tetric - color A2 submitted to accelerated artificial aging (AAA. Materials and Methods : Sixty test specimens were made of each composite (12 mm × 2 mm and separated into six groups (n = 10, according to the type of finishing/polishing to which they were submitted: C, control; F, tip 3195 F; FF, tip 3195 FF; FP, tip 3195 F + diamond paste; FFP, tip 3195 FF + diamond paste; SF, Sof-Lex discs. After polishing, controlled by an electromechanical system, initial color (spectrophotometer PCB 6807 BYK GARDNER and Ra (roughness meter Surfcorder SE 1700, cut-off 0.25 mm readings were taken. Next, the test specimens were submitted to the AAA procedure (C-UV Comexim for 384 hours, and at the end of this period, new color readings and R a were taken. Results: Statistical analysis [2-way analysis of variance (ANOVA, Bonferroni, P < 0.05] showed that all composites demonstrated ΔE alteration above the clinically acceptable limits, with the exception of Heliomolar composite in FP. The greatest ΔE alteration occurred for Tetric composite in SF (13.38 ± 2.10 statistically different from F and FF (P < 0.05. For Ra , Group F showed rougher samples than FF with statistically significant difference (P < 0.05. Conclusion: In spite of the surface differences, the different finishing/polishing procedures were not capable of providing color stability within the clinically acceptable limits.

Effect of ohmic heating processing conditions on color stability of fungal pigments.

Science.gov (United States)

Aguilar-Machado, Diederich; Morales-Oyervides, Lourdes; Contreras-Esquivel, Juan C; Aguilar, Cristóbal; Méndez-Zavala, Alejandro; Raso, Javier; Montañez, Julio

2017-06-01

The aim of this work was to analyze the effect of ohmic heating processing conditions on the color stability of a red pigment extract produced by Penicillium purpurogenum GH2 suspended in a buffer solution (pH 6) and in a beverage model system (pH 4). Color stability of pigmented extract was evaluated in the range of 60-90 ℃. The degradation pattern of pigments was well described by the first-order (fractional conversion) and Bigelow model. Degradation rate constants ranged between 0.009 and 0.088 min -1 in systems evaluated. Significant differences in the rate constant values of the ohmic heating-treated samples in comparison with conventional thermal treatment suggested a possible effect of the oscillating electric field generated during ohmic heating. The thermodynamic analysis also indicated differences in the color degradation mechanism during ohmic heating specifically when the pigment was suspended in the beverage model system. In general, red pigments produced by P. purpurogenum GH2 presented good thermal stability under the range of the evaluated experimental conditions, showing potential future applications in pasteurized food matrices using ohmic heating treatment.

Color stability and flexural strength of poly (methyl methacrylate and bis-acrylic composite based provisional crown and bridge auto-polymerizing resins exposed to beverages and food dye: An in vitro study

Directory of Open Access Journals (Sweden)

Anil K Gujjari

2013-01-01

Full Text Available Aim: To evaluate the color stability and flexural strength of poly (methyl methacrylate (PMMA and bis-acrylic composite based provisional crown and bridge auto-polymerizing resins exposed to tea, coffee, cola, and food dye. Materials and Methods: Two provisional crown and bridge resins, one DPI self-cure tooth molding powder (PMMA (Group A, and one Protemp 4 Temporization Material (bis-acrylic composite (Group B were used. Disk-shaped specimens for color stability testing (n = 30 for each material and bar-shaped specimens for flexural strength testing (n = 30 for each material were fabricated using a metal mold. The specimens were immersed in artificial saliva, artificial saliva + tea, artificial saliva + coffee, artificial saliva + cola, and artificial saliva + food dye solutions and stored in an incubator at 37°C. Color measurements were taken before immersion, and then after 3 and 7 days of immersion. Flexural strength was evaluated after 7 days of immersion. Results: Group A showed significantly higher color stability as compared to Group B, and artificial saliva + coffee solution had the most staining capacity for the resins. Test solutions had no effect on the flexural strength of Group A, but Group B specimens immersed in artificial saliva + cola showed significantly lower flexural strength values as compared to the control group. Conclusion: The findings of the study showed that for materials used in the study, PMMA was more color stable than bis-acrylic composite based resin. Also, material based on PMMA was more resistant to damage from dietary beverages as compared to bis-acrylic composite based provisional crown and bridge resin.

Characterization of active paper packaging incorporated with ginger pulp oleoresin

Science.gov (United States)

Wiastuti, T.; Khasanah, L. U.; Atmaka Kawiji, W.; Manuhara, G. J.; Utami, R.

2016-02-01

Utilization of ginger pulp waste from herbal medicine and instant drinks industry in Indonesia currently used for fertilizer and fuel, whereas the ginger pulp still contains high oleoresin. Active paper packaging were developed incorporated with ginger pulp oleoresin (0%, 2%, 4%, and 6% w/w). Physical (thickness, tensile strength, and folding endurance, moisture content), sensory characteristics and antimicrobial activity of the active paper were evaluated. Selected active paper then were chemically characterized (functional groups). The additional of ginger pulp oleoresin levels are reduced tensile strength, folding endurance and sensory characteristic (color, texture and overall) and increased antimicrobial activity. Due to physical, sensory characteristic and antimicrobial activity, active paper with 2% ginger pulp oleoresin incorporation was selected. Characteristics of selected paper were 9.93% of water content; 0.81 mm of thickness; 0.54 N / mm of tensile strength; 0.30 of folding endurance; 8.43 mm inhibits the growth of Pseudomonas fluorescence and 27.86 mm inhibits the growth of Aspergillus niger (antimicrobial activity) and neutral preference response for sensory properties. For chemical characteristic, selected paper had OH functional group of ginger in 3422.83 cm-1 of wave number and indicated contain red ginger active compounds.

Influence of pigments and opacifiers on color stability of an artificially aged facial silicone.

Science.gov (United States)

dos Santos, Daniela Micheline; Goiato, Marcelo Coelho; Moreno, Amália; Pesqueira, Aldiéris Alves; Haddad, Marcela Filiè

2011-04-01

The aim of this study was to evaluate the influence of two pigments (ceramic powder and oil paint) and one opacifier (barium sulfate) on the color stability of MDX4-4210 facial silicone submitted to accelerated aging. Sixty specimens of silicone were fabricated and divided into six groups--colorless (G1), colorless with opacifier (G2), ceramic (G3), ceramic with opacifier (G4), oil (G5), oil with opacifier (G6). All replicas were submitted to accelerated aging for 1008 hours. The evaluations of chromatic alteration through visual analysis and reflection spectrophotometry were carried out initially and after 252, 504, and 1008 hours of aging. The results were submitted to ANOVA and Tukey's test at 5% level of significance. All groups exhibited chromatic alteration (ΔE > 0); however, this color alteration was not perceptible through visual analysis of the color. The pigmented groups with opacifier presented the lowest ΔE values, with a statistical difference from the other groups. For the groups without opacifier, the group pigmented with oil paint exhibited the lowest ΔE values in the different aging periods, with a statistical difference. Accelerated aging generated significant chromatic alterations in all groups after 252 hours, except for the colorless and oil groups, both with opacifier (G2 and G6). The opacifier protects facial silicones against color degradation, and oil paint is a stable pigment even without addition of opacifier. © 2010 by The American College of Prosthodontists.

DIRECT PULP CAPPING IN TREATMENT OF REVERSIBLE PULPITIS IN PRIMARY TEETH- CLINICAL PROTOCOL

Directory of Open Access Journals (Sweden)

Nina Milcheva

2016-10-01

Full Text Available The pulp of primary teeth is identical morphologically and physiologically to that of permanent teeth and it is capable to answer to pathological stimuli by producing tertiary dentin. When the inflammation of the pulp is in its reversible stage vital methods of treatment are indicated in order to stimulate the healing processes in it and protect its vitality. In Bulgaria the most popular method of treatment of inflammation diseases of the pulp in primary dentition is the mortal amputation. The biological way of treatment is not very common even in cases where there are indications for it. Purpose: The aim of this paper is to present the approbated by us protocol for application of direct pulp capping for treatment of reversible pulpitis in primary teeth. Material and methods: On the base of world experience and our contemporary meta- analysis of the researches published in the last 15 years concerning the problems of diagnostics. We determined clinical and radiographic diagnostic criteria for reversible pulpitis in primary teeth and indications for application of direct pulp capping as a method of treatment. We give clinical steps for application of the method and summarized the clinical and radiographic criteria for success after treatment. Results/conclusion: We gather all the information for applying direct pulp cappingfor treatment of reversible pulpitis in primary dentition. We offer the method of direct pulp capping as a clinical protocol “step by step” and illustrated by scheme which can be useful for students and dentists in their everyday practice.

Fungal treatment of hemp-based pulp and paper mill wastes | Taseli ...

African Journals Online (AJOL)

based pulp and paper plant bleachery effluents in batch and up-flow column reactor studies. In batch tests, the highest removals for acid-line effluents (67% AOX (adsorbable organic halogens), 44% TOC 8 total organic carbon), 97% color) were ...

Evaluation of the Effect of Surface Polishing, Oral Beverages and Food Colorants on Color Stability and Surface Roughness of Nanocomposite Resins.

Science.gov (United States)

Kumari, R Veena; Nagaraj, Hema; Siddaraju, Kishore; Poluri, Ramya Krishna

2015-07-01

It is beyond doubt that finishing and polishing of a composite restoration enhance its esthetics and, is also essential for the health of the periodontium. A variety of instruments are commonly used for finishing and polishing tooth-colored restorative materials Thus, it is important to understand which type of surface finishing treatments would significantly affect the staining and surface irregularities of the composite resin restoration. Still one of the properties of the composite resins that have to pass the test of time is its color stability. In modern day dentistry, a large emphasis is laid over esthetics. Hence, it is important to understand the various agents capable of adversely affecting the esthetics of a restoration due to its staining capacity. Thus, the aim of this in vitro study was to evaluate the effect of surface polishing, oral beverages and food colorants on the color stability and surface roughness of nanocomposite resins. 90 Disks of nanocomposites resin (Filtek Z350 XT) measuring 8 mm in diameter and 2 mm in thickness were fabricated using a custom made silicon mold. Pre-polishing surface roughness (Ra1) of all the 90 samples were measured using a Surface Profilometer. The nano-composite disks were then randomly divided into 3 groups with 30 samples in each group. Group I: The samples were not subjected to any polishing procedures. Group II: Sof-Lex group: Samples subjected to polishing using different grits of Sof-Lex disks. Group III: Diamond polishing paste group: Samples were subjected with a polishing paste consisting of diamond particles. Following polishing procedures, the surface roughness of all samples were measured again to obtain change in surface roughness due to polishing procedures (Ra2), pre immersion spectrophotometric value (ΔE1) was also recorded for baseline color of the samples. The samples were then divided into subgroups (A, B, C, D, E), by including every first sample in Subgroup A, second in Subgroup B, third in

Visible Color and Photometry of Bright Materials on Vesta

Science.gov (United States)

Schroder, S. E.; Li, J. Y.; Mittlefehldt, D. W.; Pieters, C. M.; De Sanctis, M. C.; Hiesinger, H.; Blewett, D. T.; Russell, C. T.; Raymond, C. A.; Keller, H. U.

2012-01-01

The Dawn Framing Camera (FC) collected images of the surface of Vesta at a pixel scale of 70 m in the High Altitude Mapping Orbit (HAMO) phase through its clear and seven color filters spanning from 430 nm to 980 nm. The surface of Vesta displays a large diversity in its brightness and colors, evidently related to the diverse geology [1] and mineralogy [2]. Here we report a detailed investigation of the visible colors and photometric properties of the apparently bright materials on Vesta in order to study their origin. The global distribution and the spectroscopy of bright materials are discussed in companion papers [3, 4], and the synthesis results about the origin of Vestan bright materials are reported in [5].

The Use of Headspace Solid-Phase Microextraction (HS-SPME to Assess the Quality and Stability of Fruit Products: An Example Using Red Mombin Pulp (Spondias purpurea L.

Directory of Open Access Journals (Sweden)

Katieli Martins Todisco

2014-10-01

Full Text Available The present study aimed to evaluate the volatiles profile of red mombin (Spondias purpurea pulp and its powder produced by spray-drying (SD as an example to show utility of headspace solid-phase microextraction (HS-SPME in the analysis of parameters such as the quality and stability of fruit products. Volatiles profiles of the pulp were identified by gas chromatography-mass spectrometry (GC-MS, quantified by gas chromatography-flame ionization detector (GC-FID and compared to the profile of the powder stored at 0, 60 and 120 days in plastic (PP or laminated packages (LP. The results showed that the technique was able to identify 36 compounds in the red mombin pulp, 17 out of which have been described for the first time in this fruit, showing that red mombin fresh pulp appears to be unique in terms of volatiles composition. However, only 24 compounds were detected in the powder. This decrease is highly correlated (r2 = 0.99, at least for the majority of compounds, to the degree of volatility of compounds. Furthermore, the powder stored in PP or LP showed no statistical differences in the amounts of its components for a period of 120 days of storage. Finally, this work shows how HS-SPME analysis can be a valuable tool to assess the quality and stability of fruit products.

Do stringy corrections stabilize colored black holes?

International Nuclear Information System (INIS)

Kanti, P.; Winstanley, E.

2000-01-01

We consider hairy black hole solutions of Einstein-Yang-Mills-dilaton theory, coupled to a Gauss-Bonnet curvature term, and we study their stability under small, spacetime-dependent perturbations. We demonstrate that stringy corrections do not remove the sphaleronic instabilities of colored black holes with the number of unstable modes being equal to the number of nodes of the background gauge function. In the gravitational sector and in the limit of an infinitely large horizon, colored black holes are also found to be unstable. Similar behavior is exhibited by magnetically charged black holes while the bulk of neutral black holes are proved to be stable under small, gauge-dependent perturbations. Finally, electrically charged black holes are found to be characterized only by the existence of a gravitational sector of perturbations. As in the case of neutral black holes, we demonstrate that for the bulk of electrically charged black holes no unstable modes arise in this sector. (c) 2000 The American Physical Society

Pulp mill as an energy producer

International Nuclear Information System (INIS)

Kaulamo, O.

1998-01-01

The recovery boilers of pulp mills are today the most significant producers of wood energy. The power-to-heat ratio of the power plant process, i.e., power yield, is poor in existing applications. In the study, an alternative of improving the power yield of conventional pulp mills significantly was studied by applying solutions used in power plants to a pulp mill. Extensive conversion of wood energy into electricity is possible only in the recovery boiler of the pulp mill and in a large combustion boiler of bark, wood waste and wood chips integrated to this boiler. Hence, the harvest and transports of wood raw materials, i.e. pulp wood and energy wood, are integrated, and the fraction going to cook and the energy wood fraction are separated at the pulp mill. The method guarantees competitive supply of energy wood. As a result a SELLUPOWER mill was designed, where the recovery boiler combusting black liquor and the large power plant boiler combusting energy wood are integrated to one unit and constructed to a power plant process with a high power-to-heat ratio. Necessary technical solutions, project costs and economical feasibility compared to a conventional pulp mill were determined, and the effect of different production-economical parameters was also studied. (orig.)

Gamma ray induced chromophore modification of softwood thermomechanical pulp

International Nuclear Information System (INIS)

Robert, S.; Daneault, C.; Viel, C.; Lepine, F.

1992-01-01

This study focuses on bleaching a softwood (black spruce, balsam fur) thermomechanical pulp with gamma rays. Gamma rays are known for their enormous penetrating power, along with their ionizing properties. They can generate highly energetic radicals capable of oxidizing lignin chromophores. The authors studied the influence of isopropyl alcohol, sodium borohydride, oxygen, hydrogen peroxide, nitrogen dioxide and water along with gamma ray irradiation of the pulps. The authors measured the optimal dose and dose rate, along with the influence of the radical scavengers like oxygen on the bleaching effect of gamma irradiated pulps. They observe various degrees of bleaching of these pulps. Evidence relates this bleaching to the generation of perhydroxyl anions upon irradiation of water. Also, they were able to pinpoint the influence of the dose rate on the rate of formation and disappearance of these perhydroxyl anions and their influence on bleaching kinetics. Stability toward photoyellowing, and photoyellowing's kinetic of papers from these pulps was also studied

Carcass characteristics and meat quality of heavy swine fed different citrus pulp levels

Directory of Open Access Journals (Sweden)

P.H. Watanabe

2010-08-01

Full Text Available An assay with 36 swine initially weighting 83.7±5.1kg body weight (BW was carried out to evaluate the effects of the use of different dietary citrus pulp levels, 0, 10%, 20%, and 30%, upon digestive organs weights, carcass characteristics, and meat quality of animals subjected to qualitative feed restriction program, and slaughtered at 130kg BW. Linear response (P0.05. Higher levels of citrus pulp neither decreased backfat thickness nor increased amount of lean meat, indicative that qualitative feed restriction was not efficient. Positive linear effect (P<0.05 on pH measured 24 hours after slaughter and negative linear effect (P<0.05 on color characteristics as function of citrus pulp dietary levels were verified. Citrus pulp addition in qualitative feed restriction program may not be effective. As no deleterious effects upon meat qualities were observed, citrus pulp can be used as an alternative feedstuff for finishing swine.

Organic, cross-linking, and shape-stabilized solar thermal energy storage materials: A reversible phase transition driven by broadband visible light

International Nuclear Information System (INIS)

Wang, Yunming; Tang, Bingtao; Zhang, Shufen

2014-01-01

Graphical abstract: Organic shape-stabilized solar thermal energy storage materials (OCSPCMs) with broadband harvesting for visible light were obtained by crosslinking and color matching, which provided a new platform for improving the efficiency of solar radiation utilization. - Highlights: • Novel phase change materials (OCSPCMs) were obtained by crosslinking and color matching. • The η of the OCSPCM was higher than 0.74 (visible light from 400 nm to 700 nm). • The phase change latent heats of the OCSPCMs were more than 120 J/g. • The OCSPCM has excellent form-stable effect during phase change process. - Abstract: Broadband visible sunlight usage and shape-stabilized effect were achieved using organic, cross-linking, and shape-stabilized phase-changed materials (OCSPCMs) with broadband visible light absorption, which were obtained by cross-linking reticulation and color matching (yellow, red, and blue) according to solar irradiation energy density. The obtained OCSPCMs exhibited excellent form-stable phase-change energy storage and broadband visible light-harvesting. Under broadband irradiation (from 400 nm to 700 nm), the light-to-heat conversion and the thermal energy storage efficiency (η > 0.74) of the OCSPCMs were significantly improved upon solar irradiation by color matching compared with those of OCSPCMs with single-band selective absorption of visible light (yellow, red, or blue). Differential scanning calorimetric results indicated that the phase change temperatures and latent heats of OCSPCMs ranged from 32.6 °C to 60.2 °C and from 120.1 J/g to 132.7 J/g, respectively. The novel materials show a reversible (more than 200 cycles) phase transition via ON/OFF switching of visible light irradiation

Rheological properties of emulsions stabilized by green banana (Musa cavendishii pulp fitted by power law model

Directory of Open Access Journals (Sweden)

Dayane Rosalyn Izidoro

2009-12-01

Full Text Available In this work, the rheological behaviour of emulsions (mayonnaises stabilized by green banana pulp using the response surface methodology was studied. In addition, the emulsions stability was investigated. Five formulations were developed, according to design for constrained surfaces and mixtures, with the proportion, respectively: water/soy oil/green banana pulp: F1 (0.10/0.20/0.70, F2 (0.20/0.20/0.60, F3 (0.10/0.25/0.65, F4 (0.20/0.25/0.55 and F5 (0.15/0.225/0.625 .Emulsions rheological properties were performed with a rotational Haake Rheostress 600 rheometer and a cone and plate geometry sensor (60-mm diameter, 2º cone angle, using a gap distance of 1mm. The emulsions showed pseudoplastic behaviour and were adequately described by the Power Law model. The rheological responses were influenced by the difference in green banana pulp proportions and also by the temperatures (10 and 25ºC. The formulations with high pulp content (F1 and F3 presented higher shear stress and apparent viscosity. Response surface methodology, described by the quadratic model,showed that the consistency coefficient (K increased with the interaction between green banana pulp and soy oil concentration and the water fraction contributed to the flow behaviour index increase for all emulsions samples. Analysis of variance showed that the second-order model had not significant lack-of-fit and a significant F-value, indicating that quadratic model fitted well into the experimental data. The emulsions that presented better stability were the formulations F4 (0.20/0.25/0.55 and F5 (0.15/0.225/0.625.No presente trabalho, foi estudado o comportamento reológico de emulsões adicionadas de polpa de banana verde utilizando a metodologia de superfície de resposta e também foram investigadas a estabilidade das emulsões. Foram desenvolvidas cinco formulações, de acordo com o delineamento para superfícies limitadas e misturas, com as proporções respectivamente: água/óleo de

Optimization of Dithionite Bleaching of High Yield Bagasse Pulp

International Nuclear Information System (INIS)

Mohamed, E.

2005-01-01

High yield bagasse pulp was prepared by soaking bagasse in 10 % cold sodium hydroxide for 24 hours and then refluxing for two hours at 95 degree C. Optimization of dithionite bleaching was attained by investigation of different parameters as consistency, temperature, time and ph. Effect of additives as chelating agent (EDTA) or stabilizing of bleaching solution (Zn compound and hexamethylene tetramine) was considered. The effect of air content was also studied. One and two stages bleaching of the pulp were investigated by using sodium dithionite (D) as a sole bleaching agent or after application of one stage bleaching by hydrogen peroxide to attain high brightness for high yield pulp

Decellularized Swine Dental Pulp as a Bioscaffold for Pulp Regeneration.

Science.gov (United States)

Hu, Lei; Gao, Zhenhua; Xu, Junji; Zhu, Zhao; Fan, Zhipeng; Zhang, Chunmei; Wang, Jinsong; Wang, Songlin

2017-01-01

Endodontic regeneration shows promise in treating dental pulp diseases; however, no suitable scaffolds exist for pulp regeneration. Acellular natural extracellular matrix (ECM) is a favorable scaffold for tissue regeneration since the anatomical structure and ECM of the natural tissues or organs are well-preserved. Xenogeneic ECM is superior to autologous or allogeneic ECM in tissue engineering for its unlimited resources. This study investigated the characteristics of decellularized dental pulp ECM from swine and evaluated whether it could mediate pulp regeneration. Dental pulps were acquired from the mandible anterior teeth of swine 12 months of age and decellularized with 10% sodium dodecyl sulfate (SDS) combined with Triton X-100. Pulp regeneration was conducted by seeding human dental pulp stem cells into decellularized pulp and transplanted subcutaneously into nude mice for 8 weeks. The decellularized pulp demonstrated preserved natural shape and structure without any cellular components. Histological analysis showed excellent ECM preservation and pulp-like tissue, and newly formed mineralized tissues were regenerated after being transplanted in vivo. In conclusion, decellularized swine dental pulp maintains ECM components favoring stem cell proliferation and differentiation, thus representing a suitable scaffold for improving clinical outcomes and functions of teeth with dental pulp diseases.

Effect of different solutions on color stability of acrylic resin-based dentures

Directory of Open Access Journals (Sweden)

Marcelo Coelho Goiato

2014-01-01

Full Text Available The aim of this study was to evaluate the effect of thermocycling and immersion in mouthwash or beverage solutions on the color stability of four different acrylic resin-based dentures (Onda Cryl, OC; QC20, QC; Classico, CL; and Lucitone, LU. The factors evaluated were type of acrylic resin, immersion time, and solution (mouthwash or beverage. A total of 224 denture samples were fabricated. For each type of resin, eight samples were immersed in mouthwashes (Plax-Colgate, PC; Listerine, LI; and Oral-B, OB, beverages (coffee, CP; cola, C; and wine, W, and artificial saliva (AS; control. The color change (DE was evaluated before (baseline and after thermocycling (T1, and after immersion in solution for 1 h (T2, 3 h (T3, 24 h (T4, 48 h (T5, and 96 h (T6. The CIE Lab system was used to determine the color changes. The thermocycling test was performed for 5000 cycles. Data were submitted to three-way repeated-measures analysis of variance and Tukey's test (p < 0.05. When the samples were immersed in each mouthwash, all assessed factors, associated or not, significantly influenced the color change values, except there was no association between the mouthwash and acrylic resin. Similarly, when the samples were immersed in each beverage, all studied factors influenced the color change values. In general, regardless of the solution, LU exhibited the greatest DE values in the period from T1 to T5; and QC presented the greatest DE values at T6. Thus, thermocycling and immersion in the various solutions influenced the color stability of acrylic resins and QC showed the greatest color alteration.

Effect of different solutions on color stability of acrylic resin-based dentures.

Science.gov (United States)

Goiato, Marcelo Coelho; Nóbrega, Adhara Smith; dos Santos, Daniela Micheline; Andreotti, Agda Marobo; Moreno, Amália

2014-01-01

The aim of this study was to evaluate the effect of thermocycling and immersion in mouthwash or beverage solutions on the color stability of four different acrylic resin-based dentures (Onda Cryl, OC; QC20, QC; Classico, CL; and Lucitone, LU). The factors evaluated were type of acrylic resin, immersion time, and solution (mouthwash or beverage). A total of 224 denture samples were fabricated. For each type of resin, eight samples were immersed in mouthwashes (Plax-Colgate, PC; Listerine, LI; and Oral-B, OB), beverages (coffee, CP; cola, C; and wine, W), and artificial saliva (AS; control). The color change (DE) was evaluated before (baseline) and after thermocycling (T1), and after immersion in solution for 1 h (T2), 3 h (T3), 24 h (T4), 48 h (T5), and 96 h (T6). The CIE Lab system was used to determine the color changes. The thermocycling test was performed for 5000 cycles. Data were submitted to three-way repeated-measures analysis of variance and Tukey's test (p<0.05). When the samples were immersed in each mouthwash, all assessed factors, associated or not, significantly influenced the color change values, except there was no association between the mouthwash and acrylic resin. Similarly, when the samples were immersed in each beverage, all studied factors influenced the color change values. In general, regardless of the solution, LU exhibited the greatest DE values in the period from T1 to T5; and QC presented the greatest DE values at T6. Thus, thermocycling and immersion in the various solutions influenced the color stability of acrylic resins and QC showed the greatest color alteration.

Correlation between three-dimentional surface topography and color stability of different nanofilled composites.

Science.gov (United States)

Öztürk, Elif; Güder, Gizem

2015-01-01

The aim of this study was to evaluate the 3-dimensional (3D) surface topography and color stability of four different resin composites after immersion in different soft-beverages. One hundred sixty disk-shaped specimens (diameter: 10 mm, and thickness: 2 mm) were made from four different resin composites (i.e., Filtek Z550, Tetric N-Ceram, Clearfil Majesty Esthetic, and Cavex Quadrant Universal LC). Each specimen was cured under mylar strips for 20 sec for both top and bottom surfaces. All of the specimens were stored in distilled water for 24 h at 37°C. Surface measurements were carried out using a noncontact 3D-optical-profilometer in terms of surface topography (Ra values). Color measurements of each specimen were performed with Vita Easy Shade system. All the measurements were performed at baseline and after 30 days of immersion in the selected soft-beverages (Redbull, Coca-Cola and Dimes-Lemonade). Control groups were stored in distilled water during the study. Ra values and color changes (ΔE values) of the groups were recorded. The data were statistically analyzed using a one way ANOVA and Tukey's post-hoc tests (SPSS 18.0). The tested soft-beverages in the present study caused color changes at a 30-day evaluation period for the tested resin composites (p composites was not influenced by the tested soft-beverages (p > 0.05). There was no significant interaction between the composite and beverage type on the Ra values of the resin composites (p > 0.05). No correlation was found between color stability and 3D surface topography of the resin composites. Color stability of resin composites may be affected by soft beverages. © Wiley Periodicals, Inc.

Maceration enzymes and mannoproteins: a possible strategy to increase colloidal stability and color extraction in red wines.

Science.gov (United States)

Guadalupe, Zenaida; Palacios, Antonio; Ayestaran, Belén

2007-06-13

Different strategies were adopted to achieve increases in color stability in Tempranillo wines: (i) addition of maceration enzymes directly to the must, (ii) addition of commercial mannoproteins to the must, and (iii) inoculation of must with yeast overexpressed of mannoproteins. The addition of enzymes favored color extraction, and the wines obtained presented higher values of wine color, color intensity, bisulfite-stable color, and visually enhanced color intensity. The enzyme hydrolytic activity produced an increase in the acid polysaccharide content and polyphenol index and yielded to wines with more astringency, tannin, and length. Added mannoproteins had clearer effects on the analyzed parameters than yeast. Contrary to what may be thought, mannoproteins did not maintain the extracted polyphenols in colloidal dispersion and neither ensured color stability. These compounds clearly modified the gustative structure of the wines, enhancing the sweetness and roundness.

Effect of Whitening Toothpastes with Different Whitening Agents on the Color Stability of Orthodontic Clear Elastic Ligatures

Directory of Open Access Journals (Sweden)

Ghufran K Hussein

2018-03-01

Full Text Available Background/Purpose: The demand for invisibility appearance of fixed orthodontic appliances result in increase the use of ceramic brackets with clear auxiliaries. Elastic ligatures are one of the most widely used materials in fixed orthodontic treatment and susceptible for discoloration. The aims of this study were the evaluation and comparison the effect of brushing orthodontic clear elastic ligatures by whitening toothpastes with different whitening agents on the color stability of them. Materials and method: The sample consisted of whitening toothpastes: Kin Progressive White (Fabrique par, Barcelona, Spain, Lacalut White (Germany, Silca Brilliant White (Germany, and Opalescence White (UT, USA, also Kin Regular (Fabrique par, Barcelona, Spain (control. Sixty Ormco Clear Ligatures (Scafati, Italy used in the study, these ligatures exposed 1 hour daily to dietary media (Mixture of tea, coffee, turmeric, and mineralized water (pH=4.6 and each 10 specimens brushed with one type of toothpaste, except 10 elastics without brushing. After 4 weeks, the ligatures were assessed by a cellular attachable microscope that connected to the mobile phone according to CIE L*a*b* color system by the Adobe Photoshop program. Results: The resulting data were statistically analyzed using ANOVA and Tukey’s HSD tests which showed that the highest mean value of color change was observed in no brushing ligatures followed by Silca Brilliant White, Lacalut White, Kin Progressive White, Opalescence White, the lowest value of color change was Kin Regular. Furthermore, the increased mean value of color change was mainly affected by (CIE b* axis. Conclusion: Kin Regular toothpaste without whitening agents decreased the color change of clear ligatures more than others after exposure to staining media.

The Effect of Fluoridated and Non Fluoridated Mouth Washes on Color Stability of Different Aesthetic Arch Wires At Different Time Intervals (An in Vitro Study

Directory of Open Access Journals (Sweden)

Lubna Maky Hussein

2018-01-01

Full Text Available Background:The color stability of aesthetic arch wires is an important factor in the success of an aesthetic orthodontic treatment, but the color of these arch wires tends to change with time.This study was performed to assess the effect of two types of mouth washes on the color  stability of different types of aesthetic arch wires at different time intervals. Materials and methods:Four brands of nickel titanium coated aesthetic arch wires were used: epoxy coated (Orthotechnology and G&H and Teflon coated (Dany and Hubit.Thirty six samples were prepared, each sample contains ten halves of the aesthetic arch wires. They were divided into three groups according to the immersion media (distilled water as a control media, Listerine with fluoride and Listerine without fluoride and immersed for 30 seconds twice daily according to manufacturer's instructions to measure color change after 1 week, 3 weeks and 6 weeks by using spectrophotometer VITA Easyshade Compact according to Commission Internationale de l’Eclairage L*a*b* color space system. Results:It was found that there were highly significant differences in color change values of aesthetic arch wires among all immersion media at different time intervals and color change value increases as the time of immersion increases.Additionally, Listerine with fluoride mouth wash caused higher color change values of aesthetic arch wires than Listerine without fluoride and Hubit aesthetic arch wires were the least color stable while Orthotechnology aesthetic arch wires were the most color stable. Conclusions: We can conclude that the daily use of Listerine mouth washes could affect on the color stability of aesthetic arch wires. Although all tested aesthetic arch wires revealed color changes at variable degrees but some of these changes were not  visible and the others were clinically acceptable while the remaining were clinically unacceptable.

Composition and color stability of carbon monoxide treated dried porcine blood.

Science.gov (United States)

Fontes, P R; Gomide, L A M; Fontes, E A F; Ramos, E M; Ramos, A L S

2010-07-01

Color stability of swine blood was studied over 12 weeks of storage in plastic bags, after pH (7.40, 6.70, or 6.00) adjustment, saturation with carbon monoxide (CO) and spray-drying. CO-treated dried blood presented a redder color and higher reflectance between 610 and 700 nm, compared to a brownish-red color and lower reflectance of untreated samples. As indicated by reflectance spectra, blood pH adjustment did not influence (P>0.05) the initial color of dried blood but influenced (Pvalues, which was more pronounced in polyethylene (OTR=4130 cm(3)/m(2)/day/atm) packaged samples. After 12 weeks of storage, CO-treated samples packaged in high OTR bags presented color indexes similar to those of the untreated dried samples. CO-treated samples packaged in nylon-polyethylene (OTR=30-60 cm(3)/m(2)/day/atm) bags showed a smaller rate of discoloration and color difference (DeltaE(*)) between the CO-treated and untreated samples. Even with some darkening, packaging CO-treated dry blood in low OTR bags still gives an acceptable reddish color after 12 weeks of storage while untreated dry blood has a brownish color just after drying. Copyright 2010 Elsevier Ltd. All rights reserved.

Simple single-emitting layer hybrid white organic light emitting with high color stability

Science.gov (United States)

Nguyen, C.; Lu, Z. H.

2017-10-01

Simultaneously achieving a high efficiency and color quality at luminance levels required for solid-state lighting has been difficult for white organic light emitting diodes (OLEDs). Single-emitting layer (SEL) white OLEDs, in particular, exhibit a significant tradeoff between efficiency and color stability. Furthermore, despite the simplicity of SEL white OLEDs being its main advantage, the reported device structures are often complicated by the use of multiple blocking layers. In this paper, we report a highly simplified three-layered white OLED that achieves a low turn-on voltage of 2.7 V, an external quantum efficiency of 18.9% and power efficiency of 30 lm/W at 1000 cd/cm2. This simple white OLED also shows good color quality with a color rendering index of 75, CIE coordinates (0.42, 0.46), and little color shifting at high luminance. The device consists of a SEL sandwiched between a hole transport layer and an electron transport layer. The SEL comprises a thermally activated delayer fluorescent molecule having dual functions as a blue emitter and as a host for other lower energy emitters. The improved color stability and efficiency in such a simple device structure is explained as due to the elimination of significant energy barriers at various organic-organic interfaces in the traditional devices having multiple blocking layers.

Decellularized Swine Dental Pulp as a Bioscaffold for Pulp Regeneration

Directory of Open Access Journals (Sweden)

Lei Hu

2017-01-01

Full Text Available Endodontic regeneration shows promise in treating dental pulp diseases; however, no suitable scaffolds exist for pulp regeneration. Acellular natural extracellular matrix (ECM is a favorable scaffold for tissue regeneration since the anatomical structure and ECM of the natural tissues or organs are well-preserved. Xenogeneic ECM is superior to autologous or allogeneic ECM in tissue engineering for its unlimited resources. This study investigated the characteristics of decellularized dental pulp ECM from swine and evaluated whether it could mediate pulp regeneration. Dental pulps were acquired from the mandible anterior teeth of swine 12 months of age and decellularized with 10% sodium dodecyl sulfate (SDS combined with Triton X-100. Pulp regeneration was conducted by seeding human dental pulp stem cells into decellularized pulp and transplanted subcutaneously into nude mice for 8 weeks. The decellularized pulp demonstrated preserved natural shape and structure without any cellular components. Histological analysis showed excellent ECM preservation and pulp-like tissue, and newly formed mineralized tissues were regenerated after being transplanted in vivo. In conclusion, decellularized swine dental pulp maintains ECM components favoring stem cell proliferation and differentiation, thus representing a suitable scaffold for improving clinical outcomes and functions of teeth with dental pulp diseases.

The impact of kappa number composition on eucalyptus kraft pulp bleachability

Directory of Open Access Journals (Sweden)

M. M. Costa

2007-03-01

Full Text Available Consumption of chemicals during ECF bleaching of kraft pulp correlates reasonably well with kappa number, which measures with KMnO4 the total amount of oxidizable material in the pulp. However, the method does not distinguish between the oxidizable material in residual lignin and other structures susceptible to oxidation, such as hexenuronic acids (HexAs, extractives and carbonyl groups in the pulp. In this study an attempt is made to separate the main contributors to the kappa number in oxygen - delignified eucalyptus Kraft pulps and evaluate how these fractions behave during ECF bleaching using chlorine dioxide as the sole oxidant (DEDD sequence. Residual lignin and HexAs proved to be the main fractions contributing to the kappa number and chlorine dioxide consumption in ECF bleaching. Pulp bleachability with chlorine dioxide increases with increasing HexAs content of the pulp but chlorine dioxide per se does not react with HexAs. Reduction of pulp with sodium borohydride under conditions for removing carbonyl groups has no impact on bleachability. No correlation was found between the pulp of the extractive content and pulp bleachability. The removal of HexAs prior to ECF bleaching significantly decreases the formation of chlorinated organics in the pulp (OX and filtrates (AOX as well as of oxalic acids in the filtrates.

Evaluation of the Effects of Different Mouthrinses on the Color Stability of One Type of Glass Ionomer, Compomer and Giomer

Directory of Open Access Journals (Sweden)

Shaghayegh Razavi

2016-03-01

Full Text Available Objectives: The aim of this study was to evaluate the effect of four commercially available mouthrinses on the color stability of one type of glass ionomer, giomer and compomer. Method: 60 disc-shaped specimens, 180 in total (7*2mm, fabricated from each of the following materials: A resin modified glass ionomer Fuji II LC (GC International Corp, a giomer Beautifil II (SHOFU INC and a compomer Ionosit (DMG. All specimens were stored in artificial saliva at 37˚C for 24 hours in an incubator. The initial colour value (L*,a*,b* were recorded with spectrophotometer according to CIELAB scale. After baseline evaluation, the specimens were divided into five subgroups, according to the testing and control storage solutions (n=12. Randomly selected specimens from each material were immersed in 20 ml of the treatment solutions (Oral-B Pro Expert, Listerine, Colgate Plax, Irasha at 37˚c for 24 hours. Each specimen was then subjected to second color measurement. The collected data was statistically analyzed using two-way analysis of variance (ANOVA and Tukey’s HSD at a significance level of 0.05. Results: All samples displayed color changes after immersion in the mouthrinses. The observed color difference showed that mouthrinses have a significant effect on the color shift of tested materials. A significant interaction was found between the materials and the mouthrinses. Overall, discoloration with all mouthrinses was significant when compared to the control specimens stored in artificial saliva. Oral-B induced the highest level of discoloration (ΔE*= 11.62 in Compomer and the least discoloration was found with Irsha (ΔE*= 1.47 in RMGI. Conclusions: All tested restorative materials showed a color shift after immersion in mouthrinses, amongst which compomer displayed the highest change. Discolorations were clinically perceptible in most of the cases. Thus it can be concluded that daily use of mouthrinses increases the stainability of tested materials.

Pulping and paper properties of Palmyra palm fruit fibers

Directory of Open Access Journals (Sweden)

Waranyou Sridach

2010-05-01

Full Text Available Palmyra palm fruit fibers have the properties to be used as an alternative raw material of cellulosic pulps for papermaking.Acid and alkali pulping were investigated by using nitric acid and caustic soda on a laboratory scale, with the purpose of producing printing or writing grade pulp. The chemical composition of fiber strands from palmyra palm fruits were examined, such as holocellulose, cellulose, pentosan, lignin and extractives. The yields of acid and soda pulps were below 40%. The main physical and mechanical properties of hand sheets produced from acid and soda processes were evaluated on 80 g/m2 test sheets as functions of the following parameters: tensile index, tear index, and brightness. The mechanical properties of soda pulps were developed by twin-roll press while it was not necessary to fibrillate acidic pulps through the beating step. The soda pulp sheets presented a lower brightness than that of acidic pulp sheets. The mechanicaland physical properties of the acidic and alkaline pulps verified that they were of an acceptable quality for papermaking.

Neutron protection material and neutron protection devices made of such material

International Nuclear Information System (INIS)

Ries, W.

1984-01-01

This is concerned with a neutron protection material made of thermoplastic or thermosetting plastic from high molecule hydrocarbon compounds with particularly high hydrogen and carbon contents as braking or shielding material (moderator) for fast neutrons. The plastic can contain boron for absorbing low energy neutrons. The material is used to manufacture foil, plates, pipes, shielding walls, components, bodies for radiation protection equipment, devices and plant and for neutron protection clothes. (orig./HP) [de

Stability of astaxanthin in yogurt used to simulate apricot color, under refrigeration

Directory of Open Access Journals (Sweden)

Pedro Cerezal Mezquita

2014-09-01

Full Text Available The aim of this study was to incorporate astaxanthin to yogurts with different fat content to match apricot (Prunus armeniaca L. color. The samples containing astaxanthin were stored at 5 ± 3 °C, and color stability and astaxanthin content were determined by colorimetry and high performance liquid chromatography (HPLC, respectively. Yogurt samples were analyzed in triplicate every 24 hours for one week and subsequently every week for 3 more weeks There were no significant differences (p < 0.05 between astaxanthin concentration values at 0 and 28 days for both samples; therefore, it can be said that the fat content in the yogurt had not effect on the stability of pigment. The low dispersion of the data showed uniformity in the three chromaticity coordinates L*, a*, b* throughout the storage period for both types of yogurt. Values of ∆E ≥ 5.0 were not obtained at any time during storage, indicating high stability of the pigment.

Evaluation of bleachability on pine and eucalyptus kraft pulps

Directory of Open Access Journals (Sweden)

Marcela Freitas Andrade

2013-09-01

Full Text Available In recent decades, the pulp industry has been changing and improving its manufacturing processes in order to enhance production capacity, product quality and environmental performance. The aim of this study was to evaluate the bleachability effect on the efficient washing and alkaline leaching in eucalyptus and pine Kraft pulps using three different bleaching sequences: AD(EPD, A/D(EPDP and DHT(EPDP. This study was carried out in two stages. In the first part, the optimum conditions for pulp bleaching in order to achieve a brightness of 90% ISO were established. The second step was a comparative study between the pulps that received alkaline leaching and efficient washing with reference pulp (without treatment. The brightness, viscosity, kappa number and HexA in pulp were analyzed. The three sequences studied reached the desired brightness, but the sequence AD(EPD produced a lower reagent consumption for the same brightness. In the three sequences studied, the efficient washing of the pulp after oxygen delignification has contributed significantly to the removal of dissolved organic and inorganic materials in the pulp and the alkaline leaching decreased significantly the pulp kappa number due to a higher pulp delignification and bleachability.

Optical properties of color centers in calcium-stabilized gadolinium gallium garnets

International Nuclear Information System (INIS)

Pogatshnik, G.J.; Cain, L.S.; Chen, Y.; Evans, B.D.

1991-01-01

The addition of small amounts of calcium during the crystal growth of large-diameter, gadolinium gallium garnet (GGG) crystals creates color centers that absorb in the near-uv region of the spectrum. Ultraviolet and γ-ray irradiation of the crystals produced changes in the intensities of the uv color-center bands along with a broad absorption throughout the visible spectrum. The color center that gives rise to an absorption band at 350 nm serves as a photoionizable donor center so that uv excitation results in a visible coloration of the crystals. The effects of oxidation and reduction treatments on the strength of the color-center bands and on the radiation response of the material were examined. Photoluminescence bands were observed in both reduced GGG crystals as well as crystals that were irradiated with neutrons. Visible coloration is likely to occur during flashlamp pumping of laser rods that utilize large-diameter GGG crystals as the laser host. The changes in the optical properties of the material under uv excitation indicate that the addition of small amounts of calcium to assist in the growth of large-diameter crystals is likely to result in the degradation of laser performance

Characterization of Human Dental Pulp Tissue Under Oscillatory Shear and Compression.

Science.gov (United States)

Ozcan, Burak; Bayrak, Ece; Erisken, Cevat

2016-06-01

Availability of material as well as biological properties of native tissues is critical for biomaterial design and synthesis for regenerative engineering. Until recently, selection of biomaterials and biomolecule carriers for dental pulp regeneration has been done randomly or based on experience mainly due to the absence of benchmark data for dental pulp tissue. This study, for the first time, characterizes the linear viscoelastic material functions and compressive properties of human dental pulp tissue harvested from wisdom teeth, under oscillatory shear and compression. The results revealed a gel-like behavior of the pulp tissue over the frequency range of 0.1-100 rps. Uniaxial compression tests generated peak normal stress and compressive modulus values of 39.1 ± 20.4 kPa and 5.5 ± 2.8 kPa, respectively. Taken collectively, the linear viscoelastic and uniaxial compressive properties of the human dental pulp tissue reported here should enable the better tailoring of biomaterials or biomolecule carriers to be employed in dental pulp regeneration.

Long-term thermophilic mono-digestion of rendering wastes and co-digestion with potato pulp

International Nuclear Information System (INIS)

Bayr, S.; Ojanperä, M.; Kaparaju, P.; Rintala, J.

2014-01-01

Highlights: • Rendering wastes’ mono-digestion and co-digestion with potato pulp were studied. • CSTR process with OLR of 1.5 kg VS/m 3 d, HRT of 50 d was unstable in mono-digestion. • Free NH 3 inhibited mono-digestion of rendering wastes. • CSTR process with OLR of 1.5 kg VS/m 3 d, HRT of 50 d was stable in co-digestion. • Co-digestion increased methane yield somewhat compared to mono-digestion. - Abstract: In this study, mono-digestion of rendering wastes and co-digestion of rendering wastes with potato pulp were studied for the first time in continuous stirred tank reactor (CSTR) experiments at 55 °C. Rendering wastes have high protein and lipid contents and are considered good substrates for methane production. However, accumulation of digestion intermediate products viz., volatile fatty acids (VFAs), long chain fatty acids (LCFAs) and ammonia nitrogen (NH 4 -N and/or free NH 3 ) can cause process imbalance during the digestion. Mono-digestion of rendering wastes at an organic loading rate (OLR) of 1.5 kg volatile solids (VS)/m 3 d and hydraulic retention time (HRT) of 50 d was unstable and resulted in methane yields of 450 dm 3 /kg VS fed . On the other hand, co-digestion of rendering wastes with potato pulp (60% wet weight, WW) at the same OLR and HRT improved the process stability and increased methane yields (500–680 dm 3 /kg VS fed ). Thus, it can be concluded that co-digestion of rendering wastes with potato pulp could improve the process stability and methane yields from these difficult to treat industrial waste materials

Conservation of jucara pulp (Euterpe edulis) submitted to gamma radiation, pasteurization, lyophilization and spray drying

International Nuclear Information System (INIS)

Silva, Paula Porrelli Moreira da

2013-01-01

In Brazil there are unexplored fruit species, which represent an opportunity for producers to access special markets, where consumers appreciate the exotic character and presence of nutrients capable of preventing degenerative diseases. In this context, jucara palm (Euterpe edulis), native of the Atlantic Forest, has long been explored only for the removal of the stem, but currently the pulp of its fruit is becoming more popular. The intense purple color is due to the presence of anthocyanins, powerful antioxidants that act by inhibiting or decreasing the effects unleashed by free radicals. The pulp is highly perishable and its preservation is impossible at room temperature, lowering its market value in sales. In face of this, we need technologies that minimize nutritional and sensorial losses in order to produce healthy, tasty and long lasting foods. This study consists of five experiments with jucara pulp, which aimed to: evaluate the physico-chemical, mineral and lipid composition; realize the sensory characterization by Quantitative Descriptive Analysis (QDA); evaluate the physico-chemical and sensory conservation when submitted to radiation gamma, acidification and pasteurization, and dehydration by spray and freeze drying. The fruits have been obtained at Parque das Neblinas (Mogi das Cruzes/SP) and depulped at Agribusiness, Food and Nutrition Department (ESALQ/USP). Was verified that jucara pulp is excellent source of energy and minerals K, Fe, Co, Mg, Cu, Zn, Mn and Mo; rich in anthocyanins and fatty oils of good quality (palmitic, oleic and linoleic). The irradiation of pulp was performed at the Institute of Energy and Nuclear Research (IPEN - Sao Paulo, SP) at doses 0,0, 2,5, 5,0, 7,5 and 10,0 kGy and stored at 6 degree C for 30 days (fortnightly assessments). That process was not promising for the conservation of the product at 6 degree C, because the degradation of anthocyanins and phenolic compounds was accelerated and the color changed from purple to

Broader color gamut of color-modulating optical coating display based on indium tin oxide and phase change materials.

Science.gov (United States)

Ni, Zhigang; Mou, Shenghong; Zhou, Tong; Cheng, Zhiyuan

2018-05-01

A color-modulating optical coating display based on phase change materials (PCM) and indium tin oxide (ITO) is fabricated and analyzed. We demonstrate that altering the thickness of top-ITO in this PCM-based display device can effectively change color. The significant role of the top-ITO layer in the thin-film interference in this multilayer system is confirmed by experiment as well as simulation. The ternary-color modulation of devices with only 5 nano thin layer of phase change material is achieved. Furthermore, simulation work demonstrates that a stirringly broader color gamut can be obtained by introducing the control of the top-ITO thickness.

Material design and structural color inspired by biomimetic approach

International Nuclear Information System (INIS)

Saito, Akira

2011-01-01

Generation of structural color is one of the essential functions realized by living organisms, and its industrial reproduction can result in numerous applications. From this viewpoint, the mechanisms, materials, analytical methods and fabrication technologies of the structural color are reviewed in this paper. In particular, the basic principles of natural photonic materials, the ideas developed from these principles, the directions of applications and practical industrial realizations are presented by summarizing the recent research results. (topical review)

Effect of tomato post-harvest fungicide treatment and storage conditions on the quality of fruits, and biological value of tomato pulp and concentrated pulp

Directory of Open Access Journals (Sweden)

H. Parynow

2013-12-01

Full Text Available The influence of storage conditions on the quality of tomato fruits was tested. The rate of ripening was established in normal air, where tomatoes ripen quickly, under controlled atmosphere where they ripen more slowly and under low pressure, where they ripen slowest. The influence of post-harvest benomyl or methylthiophanate treatment on tomato rot, ripening, and biological value were examined. Post-harvest tomato treatment did not reduce fruit rot. The color of fruits and the processed products depended on the fungicide treatment. Concentrated tomato pulp made of fruits treated with methylthiophanate was redder than the others. The fungicide treatment increased or decreased the level of some chemical substances in the fruits in dependence on the applied fungicide, storage conditions and the length of storage, e.g. tomatoes treated with benomyl and stored for 14 days contained the highest level of vitamin C under 0% CO2:3%O2 and tomatoes treated with methylthiophanate contained the highest level of vitamin C under 38 mm Hg. Degradation of vitamin C in pulp was faster than in the concentrated pulp. Tomato pulp made of tomatoes treated with methylthiophanate contained the lowest level of vitamin C.

ANTIOXIDANT ACTIVITY AND PHYSICOCHEMICAL CHARACTERISTICS OF BURITI PULP (Mauritia flexuosa COLLECTED IN THE CITY OF DIAMANTINO – MTS1

Directory of Open Access Journals (Sweden)

DAYANE DE OLIVEIRA SANDRI

Full Text Available ABSTRACT Buriti is a fruit with potential for economic exploitation due to its nutritional components; however, there are few studies about their post-harvest characteristics. Thus, the aim of this study was to determine the physicochemical characteristics and analyze the antioxidant activity of Buriti pulp. Fruits were harvested at full maturity stage, sanitized, pulped and stored under refrigeration until freezing. Then, pulp was submitted to the following analyses: moisture, protein, total carbohydrates and reducing carbohydrates, ashes, lipids, crude fiber, water activity, titratable acidity (TA, pH, color, ß-carotene, a-carotene, antioxidant activity and total energy value (TEV. Analyses were performed in triplicate, and the mean, standard deviation and variation coefficient were determined. Fruit pulp presented 0.98 of water activity, TA of 8.82g/100 g of citric acid, pH 3.78, 59.69% of moisture, 20.92% of fat, 8.56 % of crude fiber, 1.04% of ash, 7.28% of total carbohydrates, 4.50% of reducing carbohydrates, 9098µg/100g of ß carotene and 10086µg/100g of a-carotene. TEV found was 228.28 kcal/100g, the color analysis showed that the pulp has an average light tint value of L * = 59.69, with high hue H * = 68.36 and vivid color with C *= 62.03. Regarding the antioxidant activity, it was observed that Buriti is a fruit that can be used to combat oxidation, as it reduced by 82.42% the amount DPPH reagent used.

Sisal organosolv pulp as reinforcement for cement based composites

Directory of Open Access Journals (Sweden)

Ana Paula Joaquim

2009-09-01

Full Text Available The present work describes non-conventional sisal (Agave sisalana chemical (organosolv pulp from residues of cordage as reinforcement to cement based materials. Sisal organosolv pulp was produced in a 1:1 ethanol/water mixture and post chemically and physically characterized in order to compare its properties with sisal kraft pulp. Cement based composites reinforced with organosolv or kraft pulps and combined with polypropylene (PP fibres were produced by the slurry de-watering and pressing method as a crude simulation of the Hatschek process. Composites were evaluated at 28 days of age, after exposition to accelerated carbonation and after 100 soak/dry cycles. Composites containing organosolv pulp presented lower mechanical strength, water absorption and apparent porosity than composites reinforced with kraft pulp. The best mechanical performance after ageing was also achieved by samples reinforced with kraft pulp. The addition of PP fibres favoured the maintenance of toughness after ageing. Accelerated carbonation promoted the densification of the composites reinforced with sisal organosolv + PP fibres.

Color stability and lipid oxidation of broiler breast meat from animals raised on organic versus non-organic production systems.

Science.gov (United States)

Viana, F M; Canto, A C V C S; Costa-Lima, B R C; Salim, A P A A; Conte-Junior, C A

2017-03-01

The aim of the present research was to evaluate the influence of organic and non-organic production systems on color stability and lipid oxidation of broiler meat Pectoralis major (PM) stored under refrigeration (4°C) for 9 days. PM samples from organic (ORG) and non-organic (NORG) production systems were compared based on physicochemical analyses (instrumental color, myoglobin concentration, metmyoglobin reducing activity (MRA), pH, and lipid oxidation) performed in 4 different trials (n = 4). In general, NORG broilers demonstrated higher (P color stability observed in NORG samples can be partly due to lipid oxidation. Therefore, the production system can affect color and lipid stability of broiler breast meat during storage. © 2016 Poultry Science Association Inc.

Color Stability of Heat‑cure Acrylic Resin Subjected to Simulated ...

African Journals Online (AJOL)

Background: Regular usage of denture cleansers is recommended in complete denture wearers for effective plaque control, and these cleansers alter the physical properties of acrylic resin over a period of time. Thus, an in vitro study was carried out to assess the effect of denture cleansers on the color stability of heat‑cure ...

In vitro study of color stability of polycrystalline and monocrystalline ceramic brackets

OpenAIRE

de Oliveira, Cibele Braga; Maia, Luiz Guilherme Martins; Santos-Pinto, Ary; Gandini J?nior, Luiz Gonzaga

2014-01-01

OBJECTIVE: The aim of this in vitro study was to analyze color stability of monocrystalline and polycrystalline ceramic brackets after immersion in dye solutions. METHODS: Seven ceramic brackets of four commercial brands were tested: Two monocrystalline and two polycrystalline. The brackets were immersed in four dye solutions (coffee, red wine, Coke and black tea) and in artificial saliva for the following times: 24 hours, 7, 14 and 21 days, respectively. Color changes were measured by a...

Influence of different staining beverages on color stability, surface roughness and microhardness of silorane and methacrylate-based composite resins.

Science.gov (United States)

Karaman, Emel; Tuncer, Duygu; Firat, Esra; Ozdemir, Oguz Suleyman; Karahan, Sevilay

2014-05-01

To investigate the influence of different staining beverages on color stability, surface roughness and microhardness of silorane and methacrylate-based composite resins. Three different composite resins (Filtek Silorane, Filtek P60, Filtek Supreme XT) were tested. Thirty cylindrical specimens (10 × 2 mm) per material were prepared and polished with a series of aluminum-oxide polishing disks. Each group was then randomly subdivided into three groups according to the test beverages: distilled water (control), cola and coffee. The samples were immersed into different beverages for 15 days. Color, surface roughness and microhardness values were measured by a spectrophotometer, prophylometer and Vickers hardness device respectively, at baseline and after 15 days. The data were subjected to statistical analysis. Immersion in coffee resulted in a significant discoloration for all the composites tested, although the color change was lower in Filtek Silorane than that of MBCs (p composites tested showed similar surface roughness changes after immersion in different beverages (p > 0.05). Besides coffee caused more roughness change than others. Immersion in coffee caused highest microhardness change in Filtek Supreme XT (p resin composites, depending on the characteristics of the materials.

Etude du séchage de la pulpe de safou ; résultats préliminaires

Directory of Open Access Journals (Sweden)

Silou, T.

1991-01-01

Full Text Available Survey on solar drying of safou pulp. Preliminary results. The consumption of safou, the fruit of Dacryodes edulis is very common in the entire Gulf of Guinea and is subject to a large trade in countries such as Cameroon, Congo, Gabon and Zaire. The fruit is very fragile with a post haverest loss of more than 50 % in the Congo. Solar dring is the only conservation method well managed by the local population but the resulting products have doubious hygenic quality. In order to appreciate the effect of drying on the product quality and in order to improve the traditional processes we have studied both the variation of residual water in the pulp and the acid index and the color of the oil. Drying with a stove (between 70 to 90°C and the solar drying give identical products in spite of some small differences in the dehydration mechanism. The resulting products have satisfying qualities : less than 1 % water content, acide index less than 4, optical density around 0, 3 at 400 nm in 25 g/1 cyclohexane. The product can be directly eaten after rehydration or reused as raw material for the extraction of oil from pulp.

Free toe pulp flap for finger pulp and volar defect reconstruction

Directory of Open Access Journals (Sweden)

Jyoshid R Balan

2016-01-01

Full Text Available Background: Fingertip injury requiring flap cover is very common in the modern era. The ideal cover should fulfill both functional and aesthetic improvement. Materials and Methods: From June 2015 to April 2016, we performed seven free toe pulp flaps for finger defect reconstruction. All patients were males. Five flaps were done in emergency post-traumatic cases, and two were done in elective set up. The cases included reconstruction of three thumbs, one index and one ring finger in an emergency set up and two ring fingers in the elective. Thumb reconstruction was done with great toe lateral pulp and the other digits reconstructed with second toe pulp flap. Follow-up evaluation included both functional and aesthetic assessment. Results: Five flaps survived completely, one suffered partial loss, and one flap failed completely. The median follow-up period was 9 months. The median duration of surgery was 255 min (range 210 to 300 min. The median two-point discrimination was 6.5 mm (range 4–8 mm. There was the return of temperature sensation in all patients; two had cold intolerance. The Semmes-Weinstein monofilament score varied from 3.61 to 5.07 (median filament index value 4.31/pressure value of 2 g/mm2. Three patients had delayed donor site wound healing. Conclusions: The free toe pulp flap is an efficient choice for fingertip and volar finger defects reconstruction with an excellent tissue match.

Long-term thermophilic mono-digestion of rendering wastes and co-digestion with potato pulp

Energy Technology Data Exchange (ETDEWEB)

Bayr, S., E-mail: suvi.bayr@jyu.fi; Ojanperä, M.; Kaparaju, P.; Rintala, J.

2014-10-15

Highlights: • Rendering wastes’ mono-digestion and co-digestion with potato pulp were studied. • CSTR process with OLR of 1.5 kg VS/m{sup 3} d, HRT of 50 d was unstable in mono-digestion. • Free NH{sub 3} inhibited mono-digestion of rendering wastes. • CSTR process with OLR of 1.5 kg VS/m{sup 3} d, HRT of 50 d was stable in co-digestion. • Co-digestion increased methane yield somewhat compared to mono-digestion. - Abstract: In this study, mono-digestion of rendering wastes and co-digestion of rendering wastes with potato pulp were studied for the first time in continuous stirred tank reactor (CSTR) experiments at 55 °C. Rendering wastes have high protein and lipid contents and are considered good substrates for methane production. However, accumulation of digestion intermediate products viz., volatile fatty acids (VFAs), long chain fatty acids (LCFAs) and ammonia nitrogen (NH{sub 4}-N and/or free NH{sub 3}) can cause process imbalance during the digestion. Mono-digestion of rendering wastes at an organic loading rate (OLR) of 1.5 kg volatile solids (VS)/m{sup 3} d and hydraulic retention time (HRT) of 50 d was unstable and resulted in methane yields of 450 dm{sup 3}/kg VS{sub fed}. On the other hand, co-digestion of rendering wastes with potato pulp (60% wet weight, WW) at the same OLR and HRT improved the process stability and increased methane yields (500–680 dm{sup 3}/kg VS{sub fed}). Thus, it can be concluded that co-digestion of rendering wastes with potato pulp could improve the process stability and methane yields from these difficult to treat industrial waste materials.

Reuse the pulp and paper industry wastewater by using fashionable technology

Science.gov (United States)

Sudarshan, K.; Maruthaiya, K.; Kotteeswaran, P.; Murugan, A.

2017-10-01

This proposed method is a promising way, which can be implemented in pulp and paper industries by effective removal of the color and chemical oxygen demand (COD) and the resulting treated water may surely reuse to the other streams. Fourier Transformer Infra Red spectra confirmed the presence of the respective functional groups in the removed pollutants from the wastewater. The efficiency of Non-ferric Alum (NF Alum) and cationic polyacrylamide (C-PAM) with and without power boiler fly ash was also studied. The reduction efficiency of color and chemical oxygen demand (COD) is evaluated at the optimum dosage of NF Alum, fly ash, and C-PAM. At the optimized pH attained from these coagulants using to treat the wastewater, the flocs formation/settling and the pollutant removal efficiency are encouraging and the resulting color of the wastewater is to 40 PtCo units from 330 PtCo units and COD to 66 mg/L from 218 mg/L. While using NF Alum alone with C-PAM for the treatment of wastewater, the highest reduction efficiency of COD is 97 mg/L from 218 mg/L and the color is 60 from 330 PtCo units at pH 4.8 was noted. From these observations, NF Alum and power boiler fly ash with C-PAM can effectively remove the pollutants from the pulp and paper mill wastewater and the water can be reused for other streams.

Color Research and Its Application to the Design of Instructional Materials.

Science.gov (United States)

Pett, Dennis; Wilson, Trudy

1996-01-01

Reviews color research and considers its implications for the design of instructional materials. Topics include physiological and psychological effects; color and learning, including attention, search tasks, retention and other objective measures, and non-objective measures; color and the cathode ray tube (CRT); and further research needs.…

Effect of different polishing systems and drinks on the color stability of resin composite.

Science.gov (United States)

Berber, Asll; Cakir, Filiz Yalcin; Baseren, Meserret; Gurgan, Sevil

2013-07-01

The purpose of this study was to evaluate the color stability of resin composit using different finishing systems and drinks. Composit disks (5 mm diameter, 2 mm thickness) were prepared for each nanofilled composite using a brass mold. The specimens were divided into 5 finishing system groups Mylar strip (Mylar, DuPont, Wilmington, Del., USA), Soft Lex (3M(™) ESPE(™) St. Paul, MN, USA), Enhance (Dentsply-DeTrey GmbHD Konstanz, Germany), Hiluster (KerrHawe, Bioggio, Switzerland), Opti Disc (KerrHawe, Bioggio, Switzerland) and each group was divided into 10 subgroups (n = 10) and stored for 24 hours at 37°C in different drinks water coffee, coffee with sugar, tea, tea with sugar, diet coke, coke, light sour cherry juice or sour cherry juice. Color of all specimens was measured before and after exposure with a spectrophotometer using CIE L*a*b* relative, and color changes (ΔE*) were then calculated. The data were analyzed with a twoway analysis of variance (ANOVA), and mean values were compared by the Tukey HSD test (p = 0.05). For the drinks, the lowest ΔE* values were observed in the water and highest ΔE* values were observed in sour cherry juice. When drinks with and without sugar were compared, all groups with sugar demonstrated a higher color difference than without sugar. For the different finishing systems, Mylar strip group demonstrated significantly highest color change; Enhance groups demonstrated significantly lowest color change. Finishing treatments and storage solutions significantly affect the color stability of resin composite. The presence of sugar in drinks increased the color difference compared to drinks without composit. Polishing techniques and drinking drinks with sugar may affect the color of esthetic restorations.

PEMUTIHAN PULP DENGAN HIDROGEN PEROKSIDA

Directory of Open Access Journals (Sweden)

Ahmad M. Fuadi

2012-01-01

Full Text Available The use of bleaching agent has increased as the result of increasing of paper consumption. The conventional bleaching agent that commonly used is material containing of chlorine. This material is not environmentally friendly and should be replaced by environmentally benign chemical, such as H2O2. About 40 gram of dry Akasia pulp was mixed with 600 ml of distilled water was put into plastic bag heated in a water bath. When the temperature reached 630C, a solution of 4 % of H2O2 and distilled water was added to obtain 5 % consistency. This mixture was put into water bath and was heated for 2 hours. The same procedure was conducted with various concentration of H2O2, time and pH. At the end of the process, the pulp was dewatered and washed. The filtrate obtained from the initial dewatering was used to determine the residual of H2O2. The pulp was analyzed to determine brightness, fiber strength and kappa number. The maximum achievement of brightness was 62,1 % ISO, 6.86 of kappa number and 1.02 kg/15 mm of fiber strength, which are reached at16 % of the use of H2O2, pH 11 and 5 hours of bleaching time. This achievement is similar to bleaching result by the additional of 4% H2O2. Inefficient usage of H2O2 was caused by some metal ions in the pulp which facilitate the decomposition of H2O2 to produce oxygen and water which has not effect on increasing the brightness. To improve the bleach ability of H2O2, initial treatment to remove metal ions from pulp should be done. Seiring dengan meningkatnya kebutuhan kertas, kebutuhan bahan pemutih juga mengalami kenaikan. Saat ini bahan pemutih yang banyak digunakan adalah senyawa yang mengandung khlor. Senyawa ini sangat tidak ramah lingkungan, oleh karena itu, perlu dicari bahan yang ramah lingkungan untuk menggantikannya. Salah satunya adalah hidrogen peroksida. Pulp dari pohon akasia sebanyak 40 gram kering dicampur dengan 600 ml aquadest dimasukkan dalam kantung plastik dipanaskan dalam water bath

Scaffolds to Control Inflammation and Facilitate Dental Pulp Regeneration

Science.gov (United States)

Colombo, John S.; Moore, Amanda N.; Hartgerink, Jeffrey D.; D’Souza, Rena N.

2014-01-01

In dentistry, the maintenance of a vital dental pulp is of paramount importance, as teeth devitalized by root canal treatment may become more brittle and prone to structural failure over time. Advanced carious lesions can irreversibly damage the dental pulp by propagating a sustained inflammatory response throughout the tissue. While the inflammatory response initially drives tissue repair, sustained inflammation has an enormously destructive effect on the vital pulp, eventually leading to total necrosis of the tissue and necessitating its removal. The implications of tooth devitalization have driven significant interest in the development of bioactive materials that facilitate the regeneration of damaged pulp tissues by harnessing the capacity of the dental pulp for self-repair. In considering the process by which pulpitis drives tissue destruction, it is clear that an important step in supporting the regeneration of pulpal tissues is the attenuation of inflammation. Macrophages, key mediators of the immune response, may play a critical role in the resolution of pulpitis due to their ability to switch to a pro-resolution phenotype. This process can be driven by the resolvins, a family of molecules derived from fatty acids that show great promise as therapeutic agents. In this review, we outline the importance of preserving the capacity of the dental pulp to self-repair through the rapid attenuation of inflammation. Potential treatment modalities, such as shifting macrophages to a pro-resolving phenotype with resolvins are described, and a range of materials known to support the regeneration of dental pulp are presented. PMID:24698696

Bleaching agent action on color stability, surface roughness and microhardness of composites submitted to accelerated artificial aging.

Science.gov (United States)

Rattacaso, Raphael Mendes Bezerra; da Fonseca Roberti Garcia, Lucas; Aguilar, Fabiano Gamero; Consani, Simonides; de Carvalho Panzeri Pires-de-Souza, Fernanda

2011-04-01

The purpose of this study was to evaluate the bleaching agent action on color stability, surface roughness and microhardness of composites (Charisma, Filtek Supreme and Heliomolar - A2) submitted to accelerated artificial aging (AAA). A Teflon matrix (12 x 2 mm) was used to fabricate 18 specimens (n=6) which, after polishing (Sof-Lex), were submitted to initial color reading (ΔE), Knoop microhardness (KHN) (50 g/15 s load) and roughness (R(a)) (cut-off 0.25 mm) tests. Afterwards, the samples were submitted to AAA for 384 hours and new color, microhardness and roughness readings were performed. After this, the samples were submitted to daily application (4 weeks) of 16% Carbamide Peroxide (NiteWhite ACP) for 8 hours and kept in artificial saliva for 16 hours. New color, microhardness and roughness readings were made at the end of the cycle, and 15 days after bleaching. Comparison of the ΔE means (2-way ANOVA, Bonferroni, P<.05) indicated clinically unacceptable color alteration for all composites after AAA, but without significant difference. Statistically significant increase in the KHN values after AAA was observed, but without significant alterations 15 days after bleaching. For R(a) there was no statistically significant difference after AAA and 15 days after bleaching. The alterations promoted by the bleaching agent and AAA are material dependent.

A Histopathological Study of Direct Pulp Capping with Adhesive Resins

Directory of Open Access Journals (Sweden)

J. Salhenejad

2004-12-01

Full Text Available Statement of Problem: Recently, it has been proposed that different adhesive materials can be used for direct pulp capping. Previous studies have demonstrated that multi steps dentin adhesives could form reparative dentin similar to calcium hydroxide (CH.Purpose: The aim of this study was to evaluate the histological pulp response of ninety mechanically exposed cat pulps to two adhesive resins (Scotch Bond MP and Single Bond 3M were compared with a calcium hydroxide cement (Dycal, Dentsply.Materials and Methods : Class V facial cavities with similar pulpal exposures were prepared in canines. In the experimental groups phosphoric acid was used to etch the enamel and dentin and pulp exposure, and after it dentin adhesives was applied. The exposure point of the control group was capped with Dycal then the remainder of the cavities was etched and a dentin adhesive (single bond was applied. All of the cavities were restored with a composite resin (Z 100 in usual manner. The animals were scarified after 7, 30 and 60 days (n=30, and the pulp evaluated histologically, statistical analysis was carried out with Kruskal- Wallis test (a=0.05.Results: The data showed that most of the cases had mild inflammation of pulp tissue.There was no significant difference in inflammatory reaction of pulp by Dycal and two adhesive systems, severe inflammatory reaction of pulp was observed only in most of the 30- day Single Bond group. Soft tissue organization of dentin bridge was less than ScotchBond and Dycal groups, the differentiation of dentin bridge was less than Scotch Bond group after 7 days.Conclusion: Slight inflammatory cell infiltration was the main reaction of exposed pulp when two commercially available adhesive resins were placed directly on the exposed pulp.There was no significant difference in inflammatory reaction of pulp between Dycal and two adhesive systems after 7 days and 60 days. After 7 days most of the specimens showed an amount of predentin

Swedish Pulp Mill Biorefineries. A vision of future possibilities

Energy Technology Data Exchange (ETDEWEB)

Berntsson, Thore (Chamers Univ. of Technology, Goeteborg (Sweden)); Axegaard, Peter; Backlund, Birgit; Samuelsson, Aasa; Berglin, Niklas; Lindgren, Karin (STFI-Packforsk, Stockholm (Sweden))

2008-07-01

Today, modern science could make it possible to develop techniques for refining almost the whole wood-matter, pulp mill side streams and bark compounds into platform chemicals, electricity, high quality fuels and structured feed-stock for chemicals and materials. The major challenge is to convert the state of basic scientific knowledge into industrial practise. Our definition of an integrated biorefinery is: 'Full utilization of the incoming biomass and other raw materials for simultaneous and economically optimized production of fibres, chemicals and energy'. Examples of products from a pulp mill biorefinery are: Chemicals and Materials (Phenols, adhesives, carbon fibres, activated carbon, binders, barriers, adhesives, antioxidants, surfactants, chelants, solvents, adhesives surfactants, descaling agents, specialty polymers, pharmaceuticals, nutraceuticals, cosmetics etc., Biofuels (pellets, lignin fuel, methanol, DME, ethanol etc), Electricity (BLGCC, condensing power etc.). The new or increased amounts of traditional products can be made from internal and/or external biomass. Three different levels can be identified: A high degree of energy saving in future mills, especially chemical pulp mills, will lead to large amounts of excess internal biomass which can be transferred to products mentioned above, Components in e.g. the black liquor, forest residues and bark can be upgraded to more valuable ones and the energy balance of the mill is kept through fuel import, wholly or partly depending on the level of mill energy efficiency. This imported fuel can be biomass or other types. External (imported) biomass (in some cases together with excess internal biomass) can be upgraded using synergy effects of docking this upgrading to a pulp mill. Electricity has been included as one of the possible biorefinery products. The electricity production in a mill can be increased in several ways which cannot be directly considered as biorefineries, e.g. recovery boiler

Integrated chemical plants at the pulp mill

Energy Technology Data Exchange (ETDEWEB)

Ehtonen, P.; Hurme, M.; Jaervelaeinen, M.

1995-12-31

The goal of this paper is to present how the chemical plants can be integrated to the pulp mill. The integration renders possible to balance the chemical consumptions. The total mass balance of a pulp mill with the incoming fuel material and the outgoing waste and flue gases are discussed. The balance figures are presented for the chemicals of the modern fibre line, which will produce fully bleached softwood pulp with an improved effluent quality. The main benefits are lower chemical and transportation costs. The principal over-all plant process block diagrams and process descriptions are presented. The presented info system provides real time information on process and production status at overall mill and department levels. (author)

Materials for the pulp and paper industry. Section 1: Development of materials for black liquor recovery boilers

Energy Technology Data Exchange (ETDEWEB)

Keiser, J.R.; Hubbard, C.R.; Payzant, E.A. [Oak Ridge National Lab., TN (United States)] [and others

1997-04-01

Black liquor recovery boilers are essential components of kraft pulp and paper mills because they are a critical element of the system used to recover the pulping chemicals required in the kraft pulping process. In addition, the steam produced in these boilers is used to generate a significant portion of the electrical power used in the mill. Recovery boilers require the largest capital investment of any individual component of a paper mill, and these boilers are a major source of material problems in a mill. The walls and floors of these boilers are constructed of tube panels that circulate high pressure water. Molten salts (smelt) accumulate on the floor of recovery boilers, and leakage of water into the boiler can result in a violent explosion when the leaked water instantly vaporizes upon contacting the molten smelt. Because corrosion of the conventionally-used carbon steel tubing was found to be excessive in the lower section of recovery boilers, use of stainless steel/carbon steel co-extruded tubing was adopted for boiler walls to lessen corrosion and reduce the likelihood of smelt/water explosions. Eventually, this co-extruded or composite (as it is known in the industry) tubing was selected for use as a portion or all of the floor of recovery boilers, particularly those operating at pressures > 6.2 MPa (900 psi), because of the corrosion problems encountered in carbon steel floor tubes. Since neither the cause of the cracking nor an effective solution has been identified, this program was established to develop a thorough understanding of the degradation that occurs in the composite tubing used for walls and floors. This is being accomplished through a program that includes collection and review of technical reports, examination of unexposed and cracked tubes from boiler floors, computer modeling to predict residual stresses under operating conditions, and operation of laboratory tests to study corrosion, stress corrosion cracking, and thermal fatigue.

Integrating the stabilization of nuclear materials

Energy Technology Data Exchange (ETDEWEB)

Dalton, H.F. [Department of Energy, Washington, DC (United States)

1996-05-01

In response to Recommendation 94-1 of the Defense Nuclear Facilities Safety Board, the Department of Energy committed to stabilizing specific nuclear materials within 3 and 8 years. These efforts are underway. The Department has already repackaged the plutonium at Rocky Flats and metal turnings at Savannah River that had been in contact with plastic. As this effort proceeds, we begin to look at activities beyond stabilization and prepare for the final disposition of these materials. To describe the plutonium materials being stabilize, Figure 1 illustrates the quantities of plutonium in various forms that will be stabilized. Plutonium as metal comprises 8.5 metric tons. Plutonium oxide contains 5.5 metric tons of plutonium. Plutonium residues and solutions, together, contain 7 metric tons of plutonium. Figure 2 shows the quantity of plutonium-bearing material in these four categories. In this depiction, 200 metric tons of plutonium residues and 400 metric tons of solutions containing plutonium constitute most of the material in the stabilization program. So, it is not surprising that much of the work in stabilization is directed toward the residues and solutions, even though they contain less of the plutonium.

Biological evaluation of nanosilver incorporated cellulose pulp for hygiene products

Energy Technology Data Exchange (ETDEWEB)

Kavitha Sankar, P.C.; Ramakrishnan, Reshmi; Rosemary, M.J., E-mail: rosemarymj@lifecarehll.com

2016-04-01

Cellulose pulp has a visible market share in personal hygiene products such as sanitary napkins and baby diapers. However it offers good surface for growth of microorganisms. Huge amount of research is going on in developing hygiene products that do not initiate microbial growth. The objective of the present work is to produce antibacterial cellulose pulp by depositing silver nanopowder on the cellulose fiber. The silver nanoparticles used were of less than 100 nm in size and were characterised using transmission electron microscopy and X-ray powder diffraction studies. Antibacterial activity of the functionalized cellulose pulp was proved by JIS L 1902 method. The in-vitro cytotoxicity, in-vivo vaginal irritation and intracutaneous reactivity studies were done with silver nanopowder incorporated cellulose pulp for introducing a new value added product to the market. Cytotoxicity evaluation suggested that the silver nanoparticle incorporated cellulose pulp is non-cytotoxic. No irritation and skin sensitization were identified in animals tested with specific extracts prepared from the test material in the in-vivo experiments. The results indicated that the silver nanopowder incorporated cellulose pulp meets the requirements of the standard practices recommended for evaluating the biological reactivity and has good biocompatibility, hence can be classified as a safe hygiene product. - Highlights: • Different amounts of silver nanoparticles (0.2 g–0.4 g/napkin) were added to cellulose pulp. • The silver nanoparticle incorporated cellulose pulp was proved to be antibacterial by JIS L 1902 method. • The minimum concentration of silver required for antibacterial activity with no cytotoxicity has been found out. • In-vivo vaginal irritation and intracutaneous reactivity studies confirmed the biocompatibility of the material.

Biological evaluation of nanosilver incorporated cellulose pulp for hygiene products

International Nuclear Information System (INIS)

Kavitha Sankar, P.C.; Ramakrishnan, Reshmi; Rosemary, M.J.

2016-01-01

Cellulose pulp has a visible market share in personal hygiene products such as sanitary napkins and baby diapers. However it offers good surface for growth of microorganisms. Huge amount of research is going on in developing hygiene products that do not initiate microbial growth. The objective of the present work is to produce antibacterial cellulose pulp by depositing silver nanopowder on the cellulose fiber. The silver nanoparticles used were of less than 100 nm in size and were characterised using transmission electron microscopy and X-ray powder diffraction studies. Antibacterial activity of the functionalized cellulose pulp was proved by JIS L 1902 method. The in-vitro cytotoxicity, in-vivo vaginal irritation and intracutaneous reactivity studies were done with silver nanopowder incorporated cellulose pulp for introducing a new value added product to the market. Cytotoxicity evaluation suggested that the silver nanoparticle incorporated cellulose pulp is non-cytotoxic. No irritation and skin sensitization were identified in animals tested with specific extracts prepared from the test material in the in-vivo experiments. The results indicated that the silver nanopowder incorporated cellulose pulp meets the requirements of the standard practices recommended for evaluating the biological reactivity and has good biocompatibility, hence can be classified as a safe hygiene product. - Highlights: • Different amounts of silver nanoparticles (0.2 g–0.4 g/napkin) were added to cellulose pulp. • The silver nanoparticle incorporated cellulose pulp was proved to be antibacterial by JIS L 1902 method. • The minimum concentration of silver required for antibacterial activity with no cytotoxicity has been found out. • In-vivo vaginal irritation and intracutaneous reactivity studies confirmed the biocompatibility of the material.

An overview of the dental pulp: its functions and responses to injury.

Science.gov (United States)

Yu, C; Abbott, P V

2007-03-01

The dental pulp is a unique tissue and its importance in the long-term prognosis of the tooth is often ignored by clinicians. It is unique in that it resides in a rigid chamber which provides strong mechanical support and protection from the microbial rich oral environment. If this rigid shell loses its structural integrity, the pulp is under the threat of the adverse stimuli from the mouth, such as caries, cracks, fractures and open restoration margins, all of which provide pathways for micro-organisms and their toxins to enter the pulp. The pulp initially responds to irritation by becoming inflamed and, if left untreated, this will progress to pulp necrosis and infection. The inflammation will also spread to the surrounding alveolar bone and cause periapical pathosis. The magnitude of pulp-related problems should not be underestimated since their most serious consequence is oral sepsis, which can be life threatening, and hence correct diagnosis and management are essential. Clinicians must have a thorough understanding of the physiological and pathological features of the dental pulp as well as the biological consequences of treatment interventions.

COLOR STABILITY OF NATURALLY DYED DENIM FABRICS

Directory of Open Access Journals (Sweden)

SUBTIRICA Adriana-Ioana

2014-05-01

Full Text Available The desire to colour textiles is as old as spinning and weaving. Natural dyes have been used since thousands of years for their long endurance, soft and elegant colours. But the invention of synthetic dyes has limited the application of natural dyes. The health hazards associated with the use of synthetic dyes and also the increased environmental awareness have revived the use of natural dyes during the recent years. The major performance characteristic of a dye is its ability to maintain the colour in normal use and is known as colorfastness. The study provides information regarding colour fastness properties of naturally dyed denim fabrics. Three vegetable materials were used for dyeing denim fabrics: Punica granatum (bark powder, Indigofera tinctoria (leave powder and Juglans regia (walnut dried shells. The results of the study indicated that using Walnut shells and Punica granatum deeper and more stable shades of colors are obtained in comparison with Indigofera Tinctoria dyed denim samples. All samples highlight a change in color in the sense of fading which has occurred to the highest extent when exposed to artificial light and washing. When tested against water, alkaline and acid perspiration, it is noticed that better results are obtained, and color change appear in a smaller extent.

Protection and control of nuclear materials

International Nuclear Information System (INIS)

Jalouneix, J.; Winter, D.

2007-01-01

In the framework of the French regulation on nuclear materials possession, the first liability is the one of operators who have to know at any time the quantity, quality and localization of any nuclear material in their possession. This requires an organization of the follow up and of the inventory of these materials together with an efficient protection against theft or sabotage. The French organization foresees a control of the implementation of this regulation at nuclear facilities and during the transport of nuclear materials by the minister of industry with the sustain of the institute of radiation protection and nuclear safety (IRSN). This article presents this organization: 1 - protection against malevolence; 2 - national protection and control of nuclear materials: goals, administrative organization, legal and regulatory content (authorization, control, sanctions), nuclear materials protection inside facilities (physical protection, follow up and inventory, security studies), protection of nuclear material transports (physical protection, follow up), control of nuclear materials (inspection at facilities, control of nuclear material measurements, inspection of nuclear materials during transport); 3 - international commitments of France: non-proliferation treaty, EURATOM regulation, international convention on the physical protection of nuclear materials, enforcement in France. (J.S.)

Chemical properties and colors of fermenting materials in salmon fish sauce production

Directory of Open Access Journals (Sweden)

Mitsutoshi Nakano

2018-02-01

Full Text Available This data article reports the chemical properties (moisture, pH, salinity, and soluble solid content and colors of fermenting materials in salmon fish sauce products. The fish sauce was produced by mixing salt with differing proportions of raw salmon materials and fermenting for three months; the salmon materials comprised flesh, viscera, an inedible portion, and soft roe. Chemical properties and colors of the unrefined fish sauce (moromi, and the refined fish sauce, were analyzed at one, two, and three months following the start of fermentation. Data determined for all products are provided in table format. Keywords: Fish sauce, Chum salmon, Fermentation, Chemical properties, Color

In vitro antibacterial activity of a novel resin-based pulp capping material containing the quaternary ammonium salt MAE-DB and Portland cement.

Science.gov (United States)

Yang, Yanwei; Huang, Li; Dong, Yan; Zhang, Hongchen; Zhou, Wei; Ban, Jinghao; Wei, Jingjing; Liu, Yan; Gao, Jing; Chen, Jihua

2014-01-01

Vital pulp preservation in the treatment of deep caries is challenging due to bacterial infection. The objectives of this study were to synthesize a novel, light-cured composite material containing bioactive calcium-silicate (Portland cement, PC) and the antimicrobial quaternary ammonium salt monomer 2-methacryloxylethyl dodecyl methyl ammonium bromide (MAE-DB) and to evaluate its effects on Streptococcus mutans growth in vitro. The experimental material was prepared from a 2 : 1 ratio of PC mixed with a resin of 2-hydroxyethylmethacrylate, bisphenol glycerolate dimethacrylate, and triethylene glycol dimethacrylate (4 : 3 : 1) containing 5 wt% MAE-DB. Cured resin containing 5% MAE-DB without PC served as the positive control material, and resin without MAE-DB or PC served as the negative control material. Mineral trioxide aggregate (MTA) and calcium hydroxide (Dycal) served as commercial controls. S. mutans biofilm formation on material surfaces and growth in the culture medium were tested according to colony-forming units (CFUs) and metabolic activity after 24 h incubation over freshly prepared samples or samples aged in water for 6 months. Biofilm formation was also assessed by Live/Dead staining and scanning electron microscopy. S. mutans biofilm formation on the experimental material was significantly inhibited, with CFU counts, metabolic activity, viability staining, and morphology similar to those of biofilms on the positive control material. None of the materials affected bacterial growth in solution. Contact-inhibition of biofilm formation was retained by the aged experimental material. Significant biofilm formation was observed on MTA and Dycal. The synthesized material containing HEMA-BisGMA-TEGDMA resin with MAE-DB as the antimicrobial agent and PC to support mineralized tissue formation inhibited S. mutans biofilm formation even after aging in water for 6 months, but had no inhibitory effect on bacteria in solution. Therefore, this material shows

The effect of solvents on the stabilities (color and Fe) of anthocyanin isolated from the red-color-melinjo peels

Energy Technology Data Exchange (ETDEWEB)

Tarmizi, Ermiziar, E-mail: uph-ermi@yahoo.com, E-mail: ermitarmizi@gmail.com; Saragih, Raskita, E-mail: raskitasaragih@yahoo.com [Indonesia Institute of Technology (ITI), Raya PuspiptekSerpong, Tangerang Banten 15320 (Indonesia); Lalasari, Latifa Hanum, E-mail: ifa-sari@yahoo.com, E-mail: lati003@lipi.go.id [Research Centre for Metallurgy and Material, Indonesian Institute of Sciences (LIPI), KawasanPuspiptekSerpong, Tangerang Selatan 15314 (Indonesia)

2015-12-29

Anthocyanin from the red-color-melinjo peels could be isolated using a polar solvent (ethanol) [ermiziar, 2010]. The amount of hydrocarbons in the structure of anthocyanin might cause that anthocyanin could be isolated using a non polar solvent. The purpose of research is to isolate anthocyanin using non polar solvents (hexane and petroleum ether) with maceration steps for 24 hours and separate solvents using rotary evaporator equipment. The stability of anthocyanin could be observed every week (1,2,3 and 4 weeks) in various environmental conditions (with or without light in refrigerator and open or closed storage). The characterization of anthocyanin was analyzed with visual (physic photo) and or using equipments such as Fourier Transform Infrared Spectroscopy (FTIR) for determining functional groups, Ultraviolet–Visible Spectroscopy (UV/Vis) with 500-550 nm wavelengths for deciding absorption of anthocyanin and atomic absorption spectroscopy (AAS) for analyzing Fe element. The result showed that anthocyanin isolation with hexane solvent has yield higher than petroleum eter solvent. From the results of physic observation for 4 weeks looked that there are changing colors of samples significant after 3 and 4 weeks in cooler with or without light. The stability of anthocyanin color was the best on the storage time until 2 weeks using hexane solvent in refrigerator and closed condition that it has absorption of 0.6740 with 500 nm wavelengths and Fe concentration 6.29 ppm.

The effect of solvents on the stabilities (color and Fe) of anthocyanin isolated from the red-color-melinjo peels

International Nuclear Information System (INIS)

Tarmizi, Ermiziar; Saragih, Raskita; Lalasari, Latifa Hanum

2015-01-01

Anthocyanin from the red-color-melinjo peels could be isolated using a polar solvent (ethanol) [ermiziar, 2010]. The amount of hydrocarbons in the structure of anthocyanin might cause that anthocyanin could be isolated using a non polar solvent. The purpose of research is to isolate anthocyanin using non polar solvents (hexane and petroleum ether) with maceration steps for 24 hours and separate solvents using rotary evaporator equipment. The stability of anthocyanin could be observed every week (1,2,3 and 4 weeks) in various environmental conditions (with or without light in refrigerator and open or closed storage). The characterization of anthocyanin was analyzed with visual (physic photo) and or using equipments such as Fourier Transform Infrared Spectroscopy (FTIR) for determining functional groups, Ultraviolet–Visible Spectroscopy (UV/Vis) with 500-550 nm wavelengths for deciding absorption of anthocyanin and atomic absorption spectroscopy (AAS) for analyzing Fe element. The result showed that anthocyanin isolation with hexane solvent has yield higher than petroleum eter solvent. From the results of physic observation for 4 weeks looked that there are changing colors of samples significant after 3 and 4 weeks in cooler with or without light. The stability of anthocyanin color was the best on the storage time until 2 weeks using hexane solvent in refrigerator and closed condition that it has absorption of 0.6740 with 500 nm wavelengths and Fe concentration 6.29 ppm

Wheat Bread with Pumpkin (Cucurbita maxima L. Pulp as a Functional Food Product

Directory of Open Access Journals (Sweden)

Renata Różyło

2014-01-01

Full Text Available In this study, a new application of pumpkin pulp in bread production is shown. The aim of this work is to determine the influence of the addition of fresh pumpkin pulp directly into wheat flour on physical, sensorial and biological properties of bread. The bioaccessibility of active compounds was also studied. An increase in the addition of pumpkin pulp from 5 to 20 % (converted to dry matter caused a decrease of bread volume and increase of crumb hardness and cohesiveness. The sensory characteristics of the bread showed that a partial replacement of wheat fl our with up to 10 % of pumpkin pulp gave satisfactory results. The taste, aroma and overall acceptability of control bread and bread containing 5 or 10 % of pulp had the highest degree of liking. The addition of higher levels of pumpkin pulp caused an unpleasant aroma and taste. Pumpkin pulp is a good material to complement the bread with potentially bioaccessible phenolics (including flavonoids and, especially, with peptides. The highest antioxidant activity was observed, in most cases, of the samples with added 10 and 15 % of pumpkin pulp. The addition of the pulp significantly enriched the bread with potentially bioaccessible angiotensin-converting enzyme (ACE inhibitors. The highest activity was determined in the bread with 15 and 20 % pumpkin pulp. ACE inhibitors from the tested bread were highly bioaccessible in vitro. Pumpkin pulp seems to be a valuable source of active compounds to complement the wheat bread. Adding the pulp directly to the wheat flour gives satisfactory baking results and reduces the cost of production. Additionally, pumpkin pulp is sometimes treated as waste material after the acquisition of seeds, thus using it as bread supplement also has environmental and economic benefi ts.

Extraction and characterization of anthocyanin colorants from plant sources

Directory of Open Access Journals (Sweden)

S. Dyankova

2016-03-01

Full Text Available Abstract. Natural pigments (and especially those of anthocyanins are a valuable source of bioactive compounds and may be used in the production of new functional food ingredients. Furthermore, their applications in the treatment and prevention of chronic disorders are becoming more and more widespread. In the last few years consumers have focused their attention on the natural biologically active compounds as functional food ingredients, and therefore, it may be assumed that natural colorants are an alternative source of synthetic additives. The aim of the study was to determine the quantitative content of monomeric anthocyanin pigments in extracts obtained from eight plants. The total content of monomeric anthocyanin pigments was measured by a pH-differential method. The TLC analysis of the pigment extracts from the different plants showed intensive rose, red and violet stripes corresponding to the anthocyanin content. The extracts from chicory and lavender petals were unstable and their color decreased in intensity in 1 month. The analysis of the experimental data shows that the yield of pigment substances depends on a few factors: the type of plant, the preliminary treatment of the plant and the solvent that is used. The largest quantity of extracted substances in the studied plants were isolated from chokeberry (2 195.9 cyd eq mg/l, followed by blackberry (1 466.2 and one variety of the grapes (1 199.3 . In the case of chokeberry, the pigment content included a large number of anthocyanins and the combination of these components was the reason for the deep red/violet color of the extract. Fresh or frozen materials are the most suitable for extraction of anthocyanin pigments. On the whole, fruit pulp yielded a larger quantity of pigments than juice. Anthocyanins are water-soluble compounds and for that reason their isolation requires water and other polar solvents. Better stabilization of color is obtained by a slight acidification of the

The Development of HfO2-Rare Earth Based Oxide Materials and Barrier Coatings for Thermal Protection Systems

Science.gov (United States)

Zhu, Dongming; Harder, Bryan James

2014-01-01

Advanced hafnia-rare earth oxides, rare earth aluminates and silicates have been developed for thermal environmental barrier systems for aerospace propulsion engine and thermal protection applications. The high temperature stability, low thermal conductivity, excellent oxidation resistance and mechanical properties of these oxide material systems make them attractive and potentially viable for thermal protection systems. This paper will focus on the development of the high performance and high temperature capable ZrO2HfO2-rare earth based alloy and compound oxide materials, processed as protective coating systems using state-or-the-art processing techniques. The emphasis has been in particular placed on assessing their temperature capability, stability and suitability for advanced space vehicle entry thermal protection systems. Fundamental thermophysical and thermomechanical properties of the material systems have been investigated at high temperatures. Laser high-heat-flux testing has also been developed to validate the material systems, and demonstrating durability under space entry high heat flux conditions.

Influence of Resin Cements on Color Stability of Different Ceramic Systems.

Science.gov (United States)

Rodrigues, Renata Borges; Lima, Erick de; Roscoe, Marina Guimarães; Soares, Carlos José; Cesar, Paulo Francisco; Novais, Veridiana Resende

2017-01-01

The purpose of this study was to evaluate color stability of two dental ceramics cemented with two resin cements, assessing the color difference (ΔE00) by the measurement of L*, a*, b*, c* and h* of transmittance. The combination of two ceramic system (feldspathic and lithium disilicate) and two resin cements - color A3 (RelyX ARC and Variolink II) resulted in 4 groups (n=5). Ten disks-shaped specimens were fabricated for each ceramic system (10x1.5 mm), etched with hydrofluoric acid (10%) and silanized prior to cementation. The color analysis was performed 24 h after cementation of the samples and after 6 months of storage in relative humidity by means of spectrophotometry. The ΔE00 values were analyzed statistically by two-way ANOVA followed by the Tukey test (p<0.05). One-way ANOVA were calculated for the means of individual color coordinates (L*, a*, b*, c* and h*). Two-way ANOVA showed that only the ceramic factor was significant (p=0.003), but there was no difference for the cement factor (p=0.275) nor for the ceramic/cement interaction (p=0.161). The feldspathic ceramic showed the highest values of ΔE00. Variations in L*, a*, b*, c* and h* were more significant for feldspathic ceramic. In conclusion, storage alters similarly the optical properties of the resin cements and feldspathic porcelain was more susceptible to cement color change after aging.

Isolation and characterization of pulp from sugarcane bagasse and rice straw

International Nuclear Information System (INIS)

Saiful Azhari, S.; Suhardy, D.; Kasim, F.H; Nazry Saleh, M.

2007-01-01

The amount of sugarcane bagasse and rice straw in the state of Perlis (Malaysia) is abundant while its utilization is still limited. One of the alternatives for the bagasse and straw utilization is as pulp raw material. This paper reviews on pulp from sugarcane bagasse and rice straw and its suitability for paper production. In this study, the pulp was extracted by the Soxhlet extraction method. The objective of this study was to investigate the cellulose, lignin and silica content of the pulp from sugarcane bagasse and rice straw. For rice straw, the presence of large amount of pentosanes in the pulp and black liquors, which also contain silica were decreased the using of straw in the paper industry. Therefore, formic acid pulping and NaOH treatment are studied to reduce or prevent silica. The isolated pulp samples were further characterized by Scanning Electron Microscope (SEM) to investigate their fiber dimensions. (Author)

Suitability of Different Natural and Synthetic Biomaterials for Dental Pulp Tissue Engineering.

Science.gov (United States)

Galler, Kerstin M; Brandl, Ferdinand P; Kirchhof, Susanne; Widbiller, Matthias; Eidt, Andreas; Buchalla, Wolfgang; Göpferich, Achim; Schmalz, Gottfried

2018-02-01

Dental pulp tissue engineering is possible after insertion of pulpal stem cells combined with a scaffold into empty root canals. Commonly used biomaterials are collagen or poly(lactic) acid, which are either difficult to modify or to insert into such a narrow space. New hydrogel scaffolds with bioactive, specifically tailored functions could optimize the conditions for this approach. Different synthetic and natural hydrogels were tested for their suitability to engineer dental pulp. Two functionalized modifications of polyethylene glycol were developed in this study and compared to a self-assembling peptide, as well as to collagen and fibrin. Cell viability of dental pulp stem cells in test materials was assessed over two weeks. Cells in selected test materials laden with dentin-derived growth factors were inserted into human tooth roots and implanted subcutaneously into immunocompromised mice. In vitro cell culture exhibited distinct differences between scaffold types, where viability was significantly higher in natural compared to synthetic materials. In vivo experiments showed considerable differences regarding scaffold degradation, soft tissue formation, vascularization, and odontoblast-like cell differentiation. Fibrin appeared most suitable to enable generation of a pulp-like tissue and differentiation of cells into odontoblasts at the cell-dentin interface. In conclusion, natural materials, especially fibrin, proved to be superior compared to synthetic scaffolds regarding cell viability and dental pulp-like tissue formation.

Oxidative stability of pork emulsion containing tomato products and pink guava pulp during refrigerated aerobic storage.

Science.gov (United States)

Joseph, Serlene; Chatli, Manish K; Biswas, Ashim K; Sahoo, Jhari

2014-11-01

Lipid oxidation-induced quality problems can be minimized with the use of natural antioxidants. Antioxidant potential of tomato puree (10 %; T-1), tomato pulp (12.5 %; T-2), lyophilized tomato peel (6 %; T-3), and pink guava pulp (10 %; T-4) was evaluated in raw pork emulsion during refrigerated storage for 9 days under aerobic packaging. The lycopene and β-carotene content varied in pork emulsion as T-3 > T-1 > T-2 > T-4 and decreased (P emulsions than in control. Overall, incorporation of tomato products and pink guava pulp improved the visual colour and odour scores of raw pork emulsion. These results indicated that tomato products and guava pulp can be utilized as sources of natural antioxidants in raw pork products to minimize lipid oxidation, off-odour development, and surface discolouration.

Abutment Material Effect on Peri-implant Soft Tissue Color and Perceived Esthetics.

Science.gov (United States)

Kim, Aram; Campbell, Stephen D; Viana, Marlos A G; Knoernschild, Kent L

2016-12-01

The purpose of this study was to evaluate the effect of implant abutment material on peri-implant soft tissue color using intraoral spectrophotometric analysis and to compare the clinical outcomes with patient and clinician perception and satisfaction. Thirty patients and four prosthodontic faculty members participated. Abutments were zirconia, gold-hued titanium, and titanium. Peri-implant mucosa color of a single anterior implant restoration was compared to the patient's control tooth. Spectrophotometric analysis using SpectroShade TM Micro data determined the color difference (ΔE, ΔL*, Δa*, Δb*) between the midfacial peri-implant soft tissue for each abutment material and the marginal gingiva of the control tooth. Color difference values of the abutment groups were compared using ANOVA (α = 0.05). Patient and clinician satisfaction surveys were also conducted using a color-correcting light source. The results of each patient and clinician survey question were compared using chi-square analysis (α = 0.05). Pearson correlation analyses identified the relationship between the total color difference (ΔE) and the patient/clinician perception and satisfaction, as well as between ΔE and tissue thickness. Zirconia abutments displayed significantly smaller spectrophotometric gingival color difference (ΔE) compared to titanium and gold-hued titanium abutments (respectively, 3.98 ± 0.99; 7.22 ± 3.31; 5.65 ± 2.11; p abutment materials, and no correlation between ΔE and the patient and clinician satisfaction. Patient satisfaction was significantly higher than clinician, and patient-perceived differences were lower than clinicians' (p abutments demonstrated significantly lower mean color difference compared to titanium or gold-hued titanium abutments as measured spectrophotometrically; however, no statistical difference in patient or clinician perception/satisfaction among abutment materials was demonstrated. Patients were significantly more satisfied than

Stability evaluation of organic Lip Balm

Directory of Open Access Journals (Sweden)

Alessandra Ribeiro Fernandes

2013-06-01

Full Text Available Rising global demand for natural products whose production is harmless to the environment has stimulated the development of natural cosmetics and, within this category, organics (95% organic raw materials. The image of environmentally friendly production is one of the strongest attractions of organic products. Lip balm is a cosmetic product similar to lipstick whose purpose is to prevent lip dryness and protect against adverse environmental factors. The product's characteristics are: resistance to temperature variations, pleasant flavor, innocuousness, smoothness during application, adherence and easy intentional removal. This work involved the development of a lip balm formulated with certified organic raw materials and the execution of stability tests: fusion point determination, evaluation of organoleptic characteristics (color, odor and appearance and functionality evaluation (spreadability test. The formulation selected after the Preliminary Stability Test was submitted to the Normal Stability Test under the following storage conditions (temperature: Room Temperature (22.0 ± 3.0 ºC, Oven (40.0 ± 2.0 ºC and Refrigerator (5.0 ± 1.0 ºC, for 90 days. Under the Refrigerator and Room Temperature conditions, spreadability proved adequate, but the surface presented white spots, characterizing the fat bloom, a phenomenon involving the recrystallization of cocoa butter. Storage at 40.0 ± 2.0 ºC (Oven caused loss of functionality according to the spreadability test, in addition to changes in color, although the aspect was uniform since the fat bloom was not observed (white spots on the surface. The odor remained stable under all conditions as did the melting point, which had a mean of 72.9 ± 1.7 ºC throughout the course of stability testing (90 days.

Effect of pasteurization temperature on stability of an acidified sugarcane juice beverage

Directory of Open Access Journals (Sweden)

Mariana Kunitake

2014-12-01

Full Text Available The shelf life of fresh sugarcane juice is quite limited due to the high rates of microbiological and enzymatic reactions which take place after extraction. In order to evaluate the impact of pasteurization temperature on quality and stability of sugarcane juice with passion fruit pulp, nine batches of sugarcane juice with 4g/100g passion fruit pulp were processed at 85, 90 and 95 °C for 30 s, in triplicate. The pasteurized beverage was aseptically packaged in polyethylene terephthalate (PET bottles and stored at 7 °C in the dark. The beverage was characterized by physicochemical tests. Activities of polyphenol oxidase (PPO and peroxidase (POD were determined before and after processing. Coliforms and Salmonella tests were carried out to assure the beverage´s microbiological safety. Color parameters were measured in the processed juice throughout the storage period. Fifty panelists evaluated the beverage's appearance, aroma, flavor, and overall impression using seven-point hedonic scale tests. Sensory stability was estimated by considering score averages above four and percentages of acceptance above 60%. The pH, soluble solids and titratable acidity of end product ranged from 3.96 to 4.19, 19.7 to 20.1 ºBrix, and 0.163 to 0.175 g/100g citric acid, respectively. The three processing binomials were effective for PPO inactivation; however, complete POD inactivation was reached at 95 °C/30 s only. The estimated sensory shelf-lives for sugarcane juice with passion fruit pulp processed at 85, 90 and 95 °C/30 s were 30, 40 and 50 days, respectively. Thus, the increase of pasteurization temperature had a positive effect on product's stability.

Radiation application for paper preservation: gamma irradiation at Eucalyptus pulp sheets

International Nuclear Information System (INIS)

Borrely, Sueli Ivone; Barbosa, Patricia S.M.; D'Almeida, Maria Luiza O.

2009-01-01

Ionizing radiation has been proposed in order to protect information and books that may be lost due to fungi and or insects infestation. In general restaurators are very worried about the maintenance of original properties of items to be treated. The selected technology must consider two points: type of biological contamination and contamination control. Fungi is one of the principal organism which grows well on papers. Once this infestation is installed on the paper it will signify spots, resistance loses and deterioration. The organisms feces introduces enzymes, organic acids and pigments to the contaminated material. Ionizing radiation from gamma sources were applied at laboratory sheets manufactured with commercial cellulose pulp. The subject of this present paper was to investigate the ideal radiation dose that is safe for keeping the paper quality. Laboratory sheets (75 g/m 2 ) were prepared in a TAPPI sheet former. Bleached sulphate Eucalyptus pulp, refined in laboratory PFI mill to 31 deg SR, was the raw material. The formed sheets were irradiated at IPEN's 60 Co Gammacell with 3 kGy up to 25 kGy. No significant changes were detected in paper samples irradiated up to 9 kGy. This is the radiation dose to be suggested. During irradiation the applied dose rate was 0.817 Gy/s. (author)

Natural Colorants: Food Colorants from Natural Sources.

Science.gov (United States)

Sigurdson, Gregory T; Tang, Peipei; Giusti, M Mónica

2017-02-28

The color of food is often associated with the flavor, safety, and nutritional value of the product. Synthetic food colorants have been used because of their high stability and low cost. However, consumer perception and demand have driven the replacement of synthetic colorants with naturally derived alternatives. Natural pigment applications can be limited by lower stability, weaker tinctorial strength, interactions with food ingredients, and inability to match desired hues. Therefore, no single naturally derived colorant can serve as a universal alternative for a specified synthetic colorant in all applications. This review summarizes major environmental and biological sources for natural colorants as well as nature-identical counterparts. Chemical characteristics of prevalent pigments, including anthocyanins, carotenoids, betalains, and chlorophylls, are described. The possible applications and hues (warm, cool, and achromatic) of currently used natural pigments, such as anthocyanins as red and blue colorants, and possible future alternatives, such as purple violacein and red pyranoanthocyanins, are also discussed.

Is Pulp Inflammation a Prerequisite for Pulp Healing and Regeneration?

Directory of Open Access Journals (Sweden)

Michel Goldberg

2015-01-01

Full Text Available The importance of inflammation has been underestimated in pulpal healing, and in the past, it has been considered only as an undesirable effect. Associated with moderate inflammation, necrosis includes pyroptosis, apoptosis, and nemosis. There are now evidences that inflammation is a prerequisite for pulp healing, with series of events ahead of regeneration. Immunocompetent cells are recruited in the apical part. They slide along the root and migrate toward the crown. Due to the high alkalinity of the capping agent, pulp cells display mild inflammation, proliferate, and increase in number and size and initiate mineralization. Pulp fibroblasts become odontoblast-like cells producing type I collagen, alkaline phosphatase, and SPARC/osteonectin. Molecules of the SIBLING family, matrix metalloproteinases, and vascular and nerve mediators are also implicated in the formation of a reparative dentinal bridge, osteo/orthodentin closing the pulp exposure. Beneath a calciotraumatic line, a thin layer identified as reactionary dentin underlines the periphery of the pulp chamber. Inflammatory and/or noninflammatory processes contribute to produce a reparative dentinal bridge closing the pulp exposure, with minute canaliculi and large tunnel defects. Depending on the form and severity of the inflammatory and noninflammatory processes, and according to the capping agent, pulp reactions are induced specifically.

Investigation of salt distribution in porous stone material using paper pulp poultices under laboratory condititions and on site

Science.gov (United States)

Egartner, Isabel; Sass, Oliver

2016-04-01

The presented investigation is part of a longer-term project which deals with the influence of salt and moisture on weathering of historic stonework. The main investigation object in the field is a part of the 300 hundred year old boundary wall of the Worchester College in Oxford, UK. A range of non-destructive techniques were applied in course of field campaigns, e.g. mapping of weathering phenomena; handheld moisture sensors; and salt sampling by paper pulp poultices. In a second step we investigated the behaviour and distribution of water and salt solution in a porous material, similar to the limestone of the College wall, under laboratory condititions. Limestone cube samples (5x5x5 cm) were soaked first with ultrapure H2O and second with different concentration of saline solutions of NaCl and Na2SO4. During the dehydration process of the stone cubes a multi-method approach including sampling by drilling, paper pulp poultices, handheld moisture sensor, conductivity sensor and Ion Chromatography (IC) were applied to investigate the moisture and salt content and distribution within the samples. The laboratory analyses were carried out at the department of applied geoscience of the Technical University of Graz, Austria. The main aim was to investigate the effectivity of the paper pulp poultices in soaking up salts from the stone samples and to use the results of the laboratory analysis to interpret and calibrate the field work results from the College wall in Oxford. Keywords: Salt weathering, paper pulp poultices, cultural heritage, field work and laboratory investigation

Stability and modification of passive films of new PUREX-materials

International Nuclear Information System (INIS)

Schultze, J.W.; Siemensmeyer, B.; Patzelt, T.

1991-10-01

The valve metals Ti, Zr and others and their alloys can be used in nitric acid solutions of the Purex process. They are protected by passive films which are stable at least at low temperatures and concentrations. Electrochemical investigations and corrosion tests are applied to check improvements of the materials. Niobium can be used to substitute the very expensive tantalum. Electrochemical and analytical investigations show the formation of the corrosion stable oxide film. Special problems are treated, such as the stability of welded joints or the influence of radioactive irradiation. α-radiation and hot atoms are simulated by ion implantation, β- and γ-radiation are simulated by laser light. In both types of experiments no decrease of stability is indicated. The alloy Ti5Ta is more stable than Ti, but it is not as good as Ta. Other alloys of Ti were investigated, but they are not suitable for the Purex process. New protection layers are tested. With respect to their preparation as well as their corrosion stability, ANOF-films are promising, but TiN-films are not stable enough. (orig.) With 71 refs., 7 tabs., 71 figs [de

Chromatic stability of acrylic resins of artificial eyes submitted to accelerated aging and polishing.

Science.gov (United States)

Goiato, Marcelo Coelho; Santos, Daniela Micheline dos; Souza, Josiene Firmino; Moreno, Amália; Pesqueira, Aldiéris Alves

2010-12-01

Esthetics and durability of materials used to fabricate artificial eyes has been an important issue since artificial eyes are essential to restore esthetics and function, protect the remaining tissues and help with patients' psychological therapy. However, these materials are submitted to degrading effects of environmental agents on the physical properties of the acrylic resin. This study assessed the color stability of acrylic resins used to fabricate sclera in three basic shades (N1, N2 and N3) when subjected to accelerated aging, mechanical and chemical polishing. Specimens of each resin were fabricated and submitted to mechanical and chemical polishing. Chromatic analysis was performed before and after accelerated aging through ultraviolet reflection spectrophotometry. All specimens revealed color alteration following polishing and accelerated aging. The resins presented statistically significant chromatic alteration (p<0.01) between the periods of 252 and 1008 h. Both polishing methods presented no significant difference between the values of color derivatives of resins.

Radiation protecting clothing materials

International Nuclear Information System (INIS)

Mio, Kotaro; Ijiri, Yasuo.

1986-01-01

Purpose: To provide radiation protecting clothing materials excellent in mechanical strength, corrosion resistance, flexibility and flexing strength. Constitution: The radiation protecting clothing materials according to this invention has pure lead sheets comprising a thin pure lead foil of 50 to 150 μm and radiation resistant organic materials, for example, polyethylene with high neutron shielding effect disposed to one or both surfaces thereof. The material are excellent in the repeating bending fatigue and mechanical strength, corrosion resistance and flexibility and, accordingly, radiation protecting clothings prepared by using them along or laminating them also possess these excellent characteristics. Further, they are excellent in the handlability, particularly, durability to the repeated holding and extension, as well as are preferable in the physical movability and feeling upon putting. The clothing materials may be cut into an appropriate size, or stitched into clothings made by radiation-resistant materials. In this case, pure lead sheets are used in lamination. (Horiuchi, T.)

Properties of Enzyme Pretreated Wikstroemia sikokiana and Broussonetia papyrifera Bast Fiber Pulps

Directory of Open Access Journals (Sweden)

Lang-Dong Lin

2015-04-01

Full Text Available Xylanase, pectinase complex, and BL11 pectinase were employed for the pretreatment of gampi and paper mulberry bast fiber pulps prior to chlorine dioxide bleaching. The bleaching efficiencies of the pulps with different enzymatic pretreatments were investigated. Accelerated aging by heat-humidity treatment was also conducted to evaluate yellowing phenomena and to estimate the prevention of brightness reversion (brightness retention by enzymatic pretreatment. The order of active chlorine required with respect to pretreatment was pectinase complex > xylanase > BL11 pectinase for soda and soda/oxalate gampi pulps and pectinase complex > BL11 pectinase > xylanase for soda and soda/oxalate paper mulberry pulps. Higher brightness retention values were observed for soda/oxalate pulps compared to soda pulps. The brightness retention levels for gampi pulps and mulberry pulps after ClO2 bleaching with enzymatic pretreatment were higher than the levels of ClO2 and NaClO bleaching pulps. Enzymatic treatments were thus able to reduce the usage of ClO2 and to assist in producing photo-stable paper materials for art and artifact-repairing applications. Thus, enzymatic pretreatment of the pulp has the potential to meet world trends and environmental sustainability for pulp and paper industries.

Semaphorin 3A Induces Odontoblastic Phenotype in Dental Pulp Stem Cells.

Science.gov (United States)

Yoshida, S; Wada, N; Hasegawa, D; Miyaji, H; Mitarai, H; Tomokiyo, A; Hamano, S; Maeda, H

2016-10-01

In cases of pulp exposure due to deep dental caries or severe traumatic injuries, existing pulp-capping materials have a limited ability to reconstruct dentin-pulp complexes and can result in pulpectomy because of their low potentials to accelerate dental pulp cell activities, such as migration, proliferation, and differentiation. Therefore, the development of more effective therapeutic agents has been anticipated for direct pulp capping. Dental pulp tissues are enriched with dental pulp stem cells (DPSCs). Here, the authors investigated the effects of semaphorin 3A (Sema3A) on various functions of human DPSCs in vitro and reparative dentin formation in vivo in a rat dental pulp exposure model. Immunofluorescence staining revealed expression of Sema3A and its receptor Nrp1 (neuropilin 1) in rat dental pulp tissue and human DPSC clones. Sema3A induced cell migration, chemotaxis, proliferation, and odontoblastic differentiation of DPSC clones. In addition, Sema3A treatment of DPSC clones increased β-catenin nuclear accumulation, upregulated expression of the FARP2 gene (FERM, RhoGEF, and pleckstrin domain protein 2), and activated Rac1 in DPSC clones. Furthermore, in the rat dental pulp exposure model, Sema3A promoted reparative dentin formation with dentin tubules and a well-aligned odontoblast-like cell layer at the dental pulp exposure site and with novel reparative dentin almost completely covering pulp tissue at 4 wk after direct pulp capping. These findings suggest that Sema3A could play an important role in dentin regeneration via canonical Wnt/β-catenin signaling. Sema3A might be an alternative agent for direct pulp capping, which requires further study. © International & American Associations for Dental Research 2016.

CLINICAL, HISTOLOGICAL AND RADIOLOGICAL ASPECTS REGARDING THE INFLUENCE OF SOME EXTERNAL FACTORS ON THE PULP-DENTIN COMPLEX

Directory of Open Access Journals (Sweden)

C. Giuroiu

2012-12-01

Full Text Available The present study aimed at assesssing – by clinical, histological and radiological investigations – the influence of some external factors on the pulp-dentin complex, and at providing a causal interpretation of the structural changes observed. Materials and methods. Clinical and radiological exams were performed on 65 old patients with ages between 60-75, and also on 40 young patients with ages between 20-35, presenting different dental-periodontal pathologies. The pulp-dentin complex was submitted to a morphopathological examination, to highlight the structural changes observed at microscopic level. Fragments of dental pulp were imersed in a 4% formaldehyde solution with phosphate buffer 0.1 M., pH 7.2, for 12 -14 hours, at a temperature of 4ºC, and 3-5 µm thick slices were prepared. The slices were coloured with hematoxylin-eosine (HE, by the trichromic technique – Masson. Photographies were taken with a Zeiss microscope, with Kodak 200 ASA. Results. Significant differences were observed, between the two groups of patients, as to the external factors that produce structural changes on pulp-dentin organ. In the group of young patients dental caries and coronal fillings prevailed, while the group of old patients was mostly associated with atrition and chronic marginal periodontitis. Out of the 40 young patients, 30 presented chronic dental caries (75%, while, among the 65 old patients, only 24 presented dental caries (36.9%. The percentages of coronary fillings between the two study groups were close, which could be considered as one of the causes producing changes in the pulp-dentin organ, following aggresive preparation of cavities, the action of materials used for the protection of pulp-dentin complex or of the materials used for coronry fillings. Conclusions. Dental pulp has a remarkable ability to counteract the action of harmful factors, producing a mineral barrier and stimulating the reparatory processes. Changes in the endodontic

C-myb Regulates Autophagy for Pulp Vitality in Glucose Oxidative Stress.

Science.gov (United States)

Lee, Y H; Kim, H S; Kim, J S; Yu, M K; Cho, S D; Jeon, J G; Yi, H K

2016-04-01

Diabetes mellitus is closely related to oral-complicated diseases by oxidative stress. This study investigates whether cellular myeloblastosis (c-myb) could protect human dental pulp cells against glucose oxidative stress and regulate autophagy activity for pulp vitality. Diabetes mellitus was induced by streptozotocin in Sprague-Dawley rats, and their pulp tissue in teeth was analyzed in terms of pulp cavity and molecules by hematoxylin and eosin and immunohistochemistry staining. Human dental pulp cells were serially subcultured and treated with glucose oxidase in the presence of elevated glucose to generate glucose oxidative stress. The replication-deficient adenovirus c-myb and small interfering RNA c-myb were introduced for c-myb expression. The pulp tissue from the diabetic rats was structurally different from normal tissue in terms of narrow pulp capacity, reduced c-myb, and dentinogenesis molecules. Glucose oxidase treatment decreased c-myb and dentinogenesis molecules (bone morphogenetic protein 2 and 7, dentin matrix protein 1, and dentin sialophosphoprotein) in human dental pulp cells. However, overexpression of c-myb by adenovirus c-myb increased dentinogenesis, autophagy molecules (autophagy protein 5, microtubule-associated protein 1A/1B-light chain 3, and Beclin-1), and cell survival via p-AMPK/AKT signaling even with glucose oxidative stress. In contrast, the lack of c-myb decreased the above molecules and cell survival by downregulating p-AMPK/AKT signaling. The results indicate that diabetes leads to irreversible damage to dental pulp, which is related to downexpression of autophagy via the p-AMPK/AKT pathway by decline of c-myb. The findings of this study provide a new insight that c-myb could ameliorate autophagy activity and that it is applicable for monitoring complicated diseases of dental pulp. The involvement of c-myb in pulp pathology could serve a therapeutic target in oral-complicated diseases. © International & American Associations

Color change at the push of a buttom; Farbwechsel auf Knopfdruck

Energy Technology Data Exchange (ETDEWEB)

Mortimer, Roger J. [Loughborough Univ. (United Kingdom)

2013-05-15

Materials with electrically switchable color open up many fascinating application possibilities - from the glare protection on low-cost displays to adaptive camouflage. Electrochromic materials can be electrically switched between different colors back and forth. The effect is based on a change of light absorption by current induced oxidation and reduction processes. Meanwhile electrochromic materials cover the entire color spectrum. In addition, the electrochromic materials are inexpensive and consume little power. This makes them attractive for many applications. However, their response times are still relatively long. The first commercial products include mirrors with automatic anti-glare and aircraft windows that can be darkened electrically.

Color change of CAD-CAM materials and composite resin cements after thermocycling.

Science.gov (United States)

Gürdal, Isil; Atay, Ayse; Eichberger, Marlis; Cal, Ebru; Üsümez, Aslihan; Stawarczyk, Bogna

2018-04-24

The color of resin cements and computer-aided-design and computer-aided-manufacturing (CAD-CAM) restorations may change with aging. The purpose of this in vitro study was to analyze the influence of thermocycling on the color of CAD-CAM materials with underlying resin cement. Seven different CAD-CAM materials, composite resins and glass-ceramics were cut into 0.7-mm and 1.2-mm thicknesses (n=10) and cemented with a dual-polymerizing resin cement, a light-polymerizing resin cement, and a preheated composite resin (N=420). Color values were measured by using spectrophotometry. Specimens were subjected to thermocycling (5°C and 55°C; 5000 cycles). The measured color difference (ΔE) data were analyzed by using descriptive statistics. Normality of data distribution was tested by using the Kolmogorov-Smirnov test. Three-way and 1-way ANOVA followed by the Scheffé post-hoc test and unpaired 2-sample Student t test were computed to determine the significant differences among the tested parameters (α=.05). ΔE values were significantly influenced by the CAD-CAM material (η p 2 =0.85, Pcement (η P 2 =0.03, P=.003) but were not influenced by thickness (P=.179). Significant interactions were present among thickness, cement, and CAD-CAM materials (Pcement showed significantly lower ΔE values than the preheated composite resin (P=.003). Restoration materials and composite resin cement types used for cementation influence the amount of color change due to aging. Copyright © 2018 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Estabilidade da polpa de pitanga sob congelamento Stability of frozen pitanga pulp

Directory of Open Access Journals (Sweden)

Alessandra S. Lopes

2005-09-01

Full Text Available Dentre as frutas tropicais, a pitanga, ainda pouco estudada, apresenta um grande apelo sensorial e uma excelente qualidade vitamínica devido ao seu elevado teor de carotenóides. Este trabalho teve como objetivo avaliar a estabilidade da polpa de pitanga preservada por congelamento (-18°C através das análises de pH, acidez total titulável, sólidos solúveis, sólidos totais, açúcares redutores e totais e aceitação sensorial nos tempos 0, 30, 60, 90 dias, carotenóides totais e cor instrumental, nos tempos 0, 15, 30, 45, 60 e 90 dias. A reação cinética da degradação do parâmetro de cor a* se ajustou melhor ao modelo cinético de 1ª ordem (R² =91,69%. No entanto, para a diferença total de cor (deltaE* apresentou melhor adequação ao modelo de ordem zero (R² =91,91%. Na análise sensorial, a aparência variou significativamente (pAmongst tropical fruits, the pitanga (Eugenia uniflora L., still little studied, shows great sensory appeal and excellent vitamin quality, due to its high carotenoid level. The objective of this study was to evaluate the stability of pitanga pulp during frozen storage (-18°C with respect to the following parameters: pH, total titratable acidity, soluble and total solids, total and reducing sugars and sensory acceptance determined after 0, 30, 60 and 90 days, and total carotenoid contents and instrumental colour measured after 0, 15, 30, 45, 60 and 90 days. The reaction kinetics for the degradation of the colour parameter a* adjusted better to a 1 order kinetic model (R² =91.69%, whereas the total difference in colour (deltaE* adjusted better to a zero order kinetic model (R² =91.91%. In the sensory analysis, the attribute of appearance varied significantly (p<0.05 after 90 days of frozen storage. Thus there was a marked fall in sensory acceptance and in the positive attitude towards buying of the nectar formulated with pitanga pulp stored for 90 days at -18°C.

NIRS Characterization of Paper Pulps to Predict Kappa Number

Directory of Open Access Journals (Sweden)

Ana Moral

2015-01-01

Full Text Available Rice is one of the most abundant food crops in the world and its straw stands as an important source of fibres both from an economic and an environmental point of view. Pulp characterization is of special relevance in works involving alternative raw materials, since pulp properties are closely linked to the quality of the final product. One of the analytical techniques that can be used in pulp characterization is near-infrared spectroscopy (NIRS. The use of NIRS has economic and technical advantages over conventional techniques. This paper aims to discuss the convenience of using NIRS to predict Kappa number in rice straw pulps produced under different conditions. We found that the resulting Kappa number can be acceptably estimated by NIRS, as the errors obtained with that method are similar to those found for other techniques.

Investigation of pulping and paper making potential of weeds

Directory of Open Access Journals (Sweden)

omid Ghaffarzadeh Mollabashi

2017-08-01

Full Text Available Increasing use of wood products accompanying with resource constraint has revealed the importance of nonwood based material. In this study, pulping and papermaking potential of three varieties of weeds including Xanthium spinosum, Carthamus tinctorius and Cyperus papyrus have been considered. At first, chemical components of the samples i.e. cellulose, lignin and extractives have been measured following TAPPI standard test methods. Afterwards, pulping process based as soda and Kraft has been carried out and the pulp properties i.e. screen yield and reject, kappa number, caliper, bust index, tear index, brightness have been considered. According to the results, the amount cellulose, lignin and extractives have been measured for the Xanthium spinosum %38.15, %13.5 and 4.72, respectively. Theses parameters have been estimated about %38.25, %10.3 and % 2.95 for Carthamus tinctorius and %38.8, %19.2 and 4.4 in case of papyrus. The yield of soda and Kraft pulp of the papyrus was more than Xanthium spinosum and Carthamus tinctorius. Among all treatments, the highest screen yield related to soda pulping of Cyperus papyrus by %39.8 which has been obtained by 175 centigrade as a maximum temperature, L/W: 6/1, active alkaline: %30 and 90 minutes as the time at temperature. The lowest and highest amounts of the tear index were related to soda pulp sample of the Carthamus tinctorius and Kraft pulp sample of Xanthium spinosum by 2.49 and 8.1, respectively. In addition, the lowest and highest amounts of the bursting index were related to soda pulp sample of the Cyperus papyrus and Kraft pulp sample of Xanthium spinosum by 0.61and 2.48, respectively. Meanwhile, soda pulp sample of the Cyperus papyrus showed the highest amount of brightness with %45 ISO.

Influence of moderate to severe chronic periodontitis on dental pulp

Science.gov (United States)

Fatemi, K; Disfani, R; Zare, R; Moeintaghavi, A; Ali, Saadat A.; Boostani, H. R

2012-01-01

Background: The relationship between periodontal disease and dental pulp changes is controversial and has been debated for many years. This human study was performed to evaluate the possible effects of moderate to advanced periodontal disease on the different aspect of dental pulp structure. Materials and Methods: Twenty hopeless permanent teeth were extracted from systemically healthy adults because of moderate to advanced chronic periodontitis, with a bone loss of >6 mm and a mobility of grade 2 or 3. Upon extraction, the apical 2 to 3 mm of the roots were immediately sectioned. Four to five sections were mounted on each slide, and every third slide was stained with hematoxylin and eosin. The specimens were histologically processed and examined by an oral pathologist. Results: Non-inflamed pulp, with partial or complete necrosis in some sections and several non-necrotic sections, was found in only 6.3% of teeth. Most teeth (58.3%) displayed edematous pulps. Slightly fibrotic pulps were seen in 52.1% of sections. Odontoblastic integrity was seen in 31.3% of teeth. Most teeth (77.1%) displayed no pulp stones. In 43.8% of teeth, the pulp vessels displayed dilatation. Conclusions: Moderate to advanced periodontal disease can affect the dental pulp. Careful consideration of diagnostic and treatment planing in patients with endodontic-periodontal involvement is therefore recommended. PMID:23493524

Color stability assessment of two different composite resins with variable immersion time using various beverages: An In vitro study

Directory of Open Access Journals (Sweden)

M Senthil Kumar

2017-01-01

Full Text Available Purpose of the Study: The aim of the study was to evaluate the difference in the color of microhybrid (MH and nanofilled (NF composite resins after 24 and 48 h in beverages such as red wine (RW, Coca-Cola, and distilled water. The specific objective of this study was to investigate the cumulative effect of the colorant solutions on the dental composites. Materials and Methods: MH and NF composite resins (A2 shade were used in this current study. Sixty disk-shaped material specimens (10 mm in diameter × 2 mm in thickness were prepared using a fiber mold (ring, with the desired dimensions. The specimen surfaces were polished using super-snap polishing system. Sixty specimens were divided into two groups of 30 each (Group I: MH resin composite; Group II: NF resin composite. Both the groups divided into six subgroups (Subgroup I: RW for 24 h [RW-24]; Subgroup II: RW for 48 h; Subgroup III: Coca-Cola for 24 h [CC-24]; Subgroup IV: Coca-Cola for 48 h [CC-48]; Subgroup V: Distilled water for 24 h [DW-24]; Subgroup VI: Distilled water for 48 h [DW-48]. All the samples were immersed in respective drinks for a period of 24 h, and color differences were measured using ultraviolet spectrophotometer. Once again, all the samples were immersed for another 24 h in the same drinks. After 48 h, the color change of the samples was measured. Measurements were made according to the CIE L × a × b × color space relative to the CIE standard illuminant D65. The color changes of the specimens were evaluated using the following formula: [INSIDE:1]Statistical analysis was performed. The data were analyzed using the one-way ANOVA and t-test at a significance level of 0.05. Conclusion: Color stability of MH composite resin was found to be inferior than the NF resin composite irrespective of immersion medium and time. In RW, the color change observed was maximum for both composite resins followed by Coca-Cola. Immersing the resin composites in distilled water for 24 and

Extraction And Stability Of Natural Colorant From Red Glutinous Rice Bran (Oryza Sativa Glutinosa

Directory of Open Access Journals (Sweden)

Tirza Hanum

2001-04-01

Full Text Available Three extraction methods were studied to isolate natural colorant from red glutinous rice bran. Stability of extracts in relation to processing conditions and in the model beverages was determined at room temperature. Identifications of anthocyanidins was performed using reversed phase HPLC. Extraction method using acidified methanol solvent showed the highest yield (260,24+28,64 mg/100g. HPLC patern indicated the presence of six major anthocyanidins, two of them were identified as apigenidin and apigenin. Stability of anthocyanin colorant was higher in a lower acid condition and was reduced to the lowest value of 49,4, 65,4, 40,8 and 36,6% by high temperature, UV light, sunlight, and the presence of oxidator agent. respectively. Retention of antocyanin in tanin and ascorbic acid added into the model beverages was lower than in protein containing beverage or control.

Universal industrial sectors integrated solutions module for the pulp and paper industry.

Science.gov (United States)

Bhander, Gurbakhash; Jozewicz, Wojciech

2017-09-01

The U.S. is the world's second-leading producer of pulp and paper products after China. Boilers, recovery furnaces, and lime kilns are the dominant sources of emissions from pulp and paper mills, collectively accounting for more than 99 % of the SO 2 , almost 96 % of the NO X , and more than 85 % of the particulate matter (PM) emitted to the air from this sector in the U.S. The process of developing industrial strategies for managing emissions can be made efficient, and the resulting strategies more cost-effective, through the application of modeling that accounts for relevant technical, environmental and economic factors. Accordingly, the United States Environmental Protection Agency is developing the Universal Industrial Sectors Integrated Solutions module for the Pulp and Paper Industry (UISIS-PNP). It can be applied to evaluate emissions and economic performance of pulp and paper mills separately under user-defined pollution control strategies. In this paper, we discuss the UISIS-PNP module, the pulp and paper market and associated air emissions from the pulp and paper sector. After illustrating the sector-based multi-product modeling structure, a hypothetical example is presented to show the engineering and economic considerations involved in the emission-reduction modeling of the pulp and paper sector in the U.S.

The Kraft Pulp And Paper Properties of Sweet Sorghum Bagasse (Sorghum bicolor L Moench

Directory of Open Access Journals (Sweden)

Widya Fatriasari

2015-05-01

Full Text Available This study investigated the potency of sweet sorghum (Sorghum bicolor bagasse as raw material for pulp and paper using kraft pulping. The effects of alkali and sulfidity loading on kraft pulp and paper properties were also investigated. The pulping condition of the kraft pulp consisted of three levels of alkali loading (17, 19 and 22% and sulfidity loading (20, 22 and 24%. The maximum cooking temperature was 170°C for 4 h with a liquid to wood ratio of 10:1. Kraft pulping of this Numbu bagasse produced good pulp indicated by high screen yield and delignification selectivity with a low Kappa number (< 10. The unbleached pulp sheet produced a superior brightness level and a high burst index. The increase of active alkali loading tended to produce a negative effect on the pulp yield, Kappa number and paper sheet properties. Therefore, it is suggested to use a lower active alkaline concentration.

In vitro study of color stability of polycrystalline and monocrystalline ceramic brackets.

Science.gov (United States)

de Oliveira, Cibele Braga; Maia, Luiz Guilherme Martins; Santos-Pinto, Ary; Gandini Junior, Luiz Gonzaga

2014-01-01

The aim of this in vitro study was to analyze color stability of monocrystalline and polycrystalline ceramic brackets after immersion in dye solutions. Seven ceramic brackets of four commercial brands were tested: Two monocrystalline and two polycrystalline. The brackets were immersed in four dye solutions (coffee, red wine, Coke and black tea) and in artificial saliva for the following times: 24 hours, 7, 14 and 21 days, respectively. Color changes were measured by a spectrophotometer. Data were assessed by Multivariate Profile Analysis, Analysis of Variance (ANOVA) and Multiple Comparison Tests of means. There was a perceptible change of color in all ceramic brackets immersed in coffee (ΔE* Allure = 7.61, Inspire Ice = 6.09, Radiance = 6.69, Transcend = 7.44), black tea (ΔE* Allure = 6.24, Inspire Ice = 5.21, Radiance = 6.51, Transcend = 6.14) and red wine (ΔE* Allure = 6.49, Inspire Ice = 4.76, Radiance = 5.19, Transcend = 5.64), but no change was noticed in Coke and artificial saliva (ΔE brackets undergo color change when exposed to solutions of coffee, black tea and red wine. However, the same crystalline structure, either monocrystalline or polycrystalline, do not follow the same or a similar pattern in color change, varying according to the bracket fabrication, which shows a lack of standardization in the manufacturing process. Coffee dye produced the most marked color changes after 21 days of immersion for most ceramic brackets evaluated.

Study of shifting of recombination zone in multi-emissive layer organic light emitting devices and its effect on color stability

International Nuclear Information System (INIS)

Tyagi, Priyanka; Srivastava, Ritu; Kumar, Arunandan; Tuli, Suneet; Kamalasanan, M.N.

2013-01-01

Color stability in multi-emissive layer organic light emitting devices (Me-OLEDs) has been investigated. Me-OLEDs were based on multiple emitters with a common host CBP doped with three dopants, BCzVBi, Ir(ppy) 3 and Ir(btp) 2 acac for blue, green and red emission. A major variation in CIE coordinates were found from (0.312, 0.294) to (0.236, 0.267) with increase in voltage from 6 to 9 V. This coordinate shift in Me-OLEDs has been attributed to the shifting of recombination zone with increase in voltage. In order to support our experimental observation, the EL spectrum of Me-OLEDs has been expressed as a linear combination of EL intensities of OLEDs with its individual constituting layers as emitters. In this way, the contribution of each layer in the EL spectrum of Me-OLEDs has been evaluated at each voltage. It has been observed from these calculations that the contribution of red emitter decreases from 47% to 33.33% and blue emitter increases from 38% to 51.67% with the increase in voltage from 6 to 9 V. This supports our hypothesis of shifting of recombination zone with the change in voltage. This shifting has been attributed to the field dependency of electron mobility in CBP. Me-OLED with CBP layers between the emitters was fabricated to improve the color stability. Significant improvement in color stability was achieved without changes in current efficiency in Me-OLED with interlayers. Highlights: ► Me-OLEDs have been fabricated by using three primary colors (RGB). ► CIE coordinates of these Me-OLEDs were voltage dependent. ► Analytical fitting has been performed to study the shifting of recombination zone. ► CBP interlayers have been introduced to improve the color stability. ► Color stability has been improved without any change in current efficiency

Chemical properties and colors of fermenting materials in salmon fish sauce production.

Science.gov (United States)

Nakano, Mitsutoshi; Sagane, Yoshimasa; Koizumi, Ryosuke; Nakazawa, Yozo; Yamazaki, Masao; Watanabe, Toshihiro; Takano, Katsumi; Sato, Hiroaki

2018-02-01

This data article reports the chemical properties (moisture, pH, salinity, and soluble solid content) and colors of fermenting materials in salmon fish sauce products. The fish sauce was produced by mixing salt with differing proportions of raw salmon materials and fermenting for three months; the salmon materials comprised flesh, viscera, an inedible portion, and soft roe. Chemical properties and colors of the unrefined fish sauce ( moromi ), and the refined fish sauce, were analyzed at one, two, and three months following the start of fermentation. Data determined for all products are provided in table format.

Evaluation of chemical characteristics and correlation analysis with pulp browning of advanced selections of apples grown in Brazil

Directory of Open Access Journals (Sweden)

Luciana Ercoli

2017-02-01

Full Text Available In this research, the total phenolic content (TPC and antioxidant capacity (FRAP and DPPH•× assays of pulps and peels of advanced selection of apples grown in Brazil were investigated. The correlation analyses between the activity of polyphenoloxidase enzyme (PPO, vitamin C content, total titratable acidity, and color parameters were performed. The results indicated that the data differed significantly among the apple genotypes studied. The peels of the selection Epagri 170-91 and Epagri 170-25 showed the highest TPC and antioxidant capacities. In addition, the pulps of the Epagri 170-91 presented the highest TPC and antioxidant capacities, the lowest enzymatic browning, highest amount of vitamin C and lowest enzymatic activity when compared with other genotypes. The TPC and antioxidant capacities were significantly correlated in all genotypes analyzed. High correlation values between enzymatic browning and factors that affect the apple color were also found in all analyzed pulps, except between enzymatic browning and TPC. The results demonstrated that the enzymatic browning and TPC, as well as the antioxidant capacity and chemical characteristics, vary considerably depending on the apple genotypes and fruit tissues analyzed.

Study on the light-color mixing of rare earth luminescent materials for anti-counterfeiting application

Science.gov (United States)

Zhang, Jishu; Zhang, Yingzi; Tao, Jin; Zhu, Yanan

2018-04-01

In order to find out the light color mixing mechanism of rare earth luminescent materials used in anti-counterfeiting fibers, we prepared three kinds of rare earth luminescent materials according to RGB tri-primary color, and mixed it together to form different mixtures in certain proportion. The phase structures of the luminescent material monomers were measured by x-ray diffractometer. The photochromic properties of the luminescent materials were tested and analyzed by fluorescence spectrophotometer. The results show that the light color mixing was consistent with the blending principle of additive color, but not the same because of the photochromic properties of rare earth luminescent materials, and we explored the reasons in the light wavelength and intensity. It was found that the enhancement of the luminescence intensity of the mixture on account of the superimposing of luminescence.

Potential mechanisms of carbon monoxide and high oxygen packaging in maintaining color stability of different bovine muscles.

Science.gov (United States)

Liu, Chenglong; Zhang, Yimin; Yang, Xiaoyin; Liang, Rongrong; Mao, Yanwei; Hou, Xu; Lu, Xiao; Luo, Xin

2014-06-01

The objectives were to compare the effects of packaging methods on color stability, metmyoglobin-reducing-activity (MRA), total-reducing-activity and NADH concentration of different bovine muscles and to explore potential mechanisms in the enhanced color stability by carbon monoxide modified atmosphere packaging (CO-MAP, 0.4% CO/30% CO2/69.6% N2). Steaks from longissimus lumborum (LL), psoas major (PM) and longissimus thoracis (LT) packaged in CO-MAP, high-oxygen modified atmosphere packaging (HiOx-MAP, 80% O2/20% CO2) or vacuum packaging were stored for 0day, 4days, 9days, and 14days or stored for 9days then displayed in air for 0day, 1day, or 3days. The CO-MAP significantly increased red color stability of all muscles, and especially for PM. The PM and LT were more red than LL in CO-MAP, whereas PM had lowest redness in HiOx-MAP. The content of MetMb in CO-MAP was lower than in HiOx-MAP. Steaks in CO-MAP maintained a higher MRA compared with those in HiOx-MAP during storage. After opening packages, the red color of steaks in CO-MAP deteriorated more slowly compared with that of steaks in HiOx-MAP. Copyright © 2014 Elsevier Ltd. All rights reserved.

Color stabilization of porcine hemoglobin during spray-drying and powder storage by combining chelating and reducing agents.

Science.gov (United States)

Salvador, P; Toldrà, M; Parés, D; Carretero, C; Saguer, E

2009-10-01

This work focuses on the effects of adding a chelating agent - such as nicotinic acid (NA, 2% w/v) or nicotinamide (Nam, 2.5% w/v) - along with glucose as a reducing agent (G, 10% w/v) to fresh porcine hemoglobin in order to stabilize its red color during spray-drying and powder storage at room temperature. Correlations between the CIELAB color parameters and the relative percentages of the different hemoglobin derivatives (liganded and deliganded ferrohemoglobin, and methemoglobin) were analyzed. The results indicate that, although little effects could be observed for any of the combined treatments on fresh hemoglobin, they were effective against pigment autoxidation during dehydration and subsequent storage. From the results, it can also be concluded that glucose was the main contributor to the color stabilization of the hemoglobin powder, probably due to its high water retention capacity.

Project Management Plan for Material Stabilization

International Nuclear Information System (INIS)

SPEER, D.R.

1999-01-01

This plan presents the overall objectives, description, justification and planning for the plutonium Finishing Plant (PFP) Materials Stabilization project. The intent of this plan is to describe how this project will be managed and integrated with other facility stabilization and deactivation activities. This plan supplements the overall integrated plan presented in the Plutonium Finishing Plant Integrated Project Management Plan (IPMP), HNF-3617/Rev. 0. This is the top-level definitive project management document that specifies the technical (work scope), schedule, and cost baselines to manager the execution of this project. It describes the organizational approach and roles/responsibilities to be implemented to execute the project. This plan is under configuration management and any deviations must be authorized by appropriate change control action. Materials stabilization is designated the responsibility to open and stabilize containers of plutonium metal, oxides, alloys, compounds, and sources. Each of these items is at least 30 weight percent plutonium/uranium. The output of this project will be containers of materials in a safe and stable form suitable for storage pending final packaging and/or transportation offsite. The corrosion products along with oxides and compounds will be stabilized via muffle furnaces to reduce the materials to high fired oxides

Protection enhances community and habitat stability: evidence from a mediterranean marine protected area.

Science.gov (United States)

Fraschetti, Simonetta; Guarnieri, Giuseppe; Bevilacqua, Stanislao; Terlizzi, Antonio; Boero, Ferdinando

2013-01-01

Rare evidences support that Marine Protected Areas (MPAs) enhance the stability of marine habitats and assemblages. Based on nine years of observation (2001-2009) inside and outside a well managed MPA, we assessed the potential of conservation and management actions to modify patterns of spatial and/or temporal variability of Posidonia oceanica meadows, the lower midlittoral and the shallow infralittoral rock assemblages. Significant differences in both temporal variations and spatial patterns were observed between protected and unprotected locations. A lower temporal variability in the protected vs. unprotected assemblages was found in the shallow infralittoral, demonstrating that, at least at local scale, protection can enhance community stability. Macrobenthos with long-lived and relatively slow-growing invertebrates and structurally complex algal forms were homogeneously distributed in space and went through little fluctuations in time. In contrast, a mosaic of disturbed patches featured unprotected locations, with small-scale shifts from macroalgal stands to barrens, and harsh temporal variations between the two states. Opposite patterns of spatial and temporal variability were found for the midlittoral assemblages. Despite an overall clear pattern of seagrass regression through time, protected meadows showed a significantly higher shoot density than unprotected ones, suggesting a higher resistance to local human activities. Our results support the assumption that the exclusion/management of human activities within MPAs enhance the stability of the structural components of protected marine systems, reverting or arresting threat-induced trajectories of change.

PRODUCTION OF PRINTING AND WRITING PAPER GRADE PULP FROM ELEPHANT GRASS

Directory of Open Access Journals (Sweden)

Marcela Freitas Andrade

2016-09-01

Full Text Available The main goal of this study was to characterize chemically and morphologically elephant grass (Pennisetum purpureum, and evaluate the potential of its fibers for production of printing and writing paper grade pulp. The elephant grass was chemically and morphologically characterized and cooked by the soda process to two different degrees of delignification (kappa 17.5 and 10.6. The resulting pulps were fully bleached by the O-D*-(EP-D sequence and characterized for their beatability, drainability and physical-mechanical properties. The lignin content (20.2% was low, indicating that this grass should be easier to pulp. The morphological analyses of the elephant grass indicated a short fiber material, similar to hardwoods. The soda pulp from elephant grass cooked to kappa number 17.5 presented higher screened yield than 10.6 kappa pulp, with alkali demands of 15.0% and 20.0%, respectively. The total active chlorine required by the 17.5 and 10.6 kappa pulps, were 42.1 and 35.1 kg/odt pulp, respectively, to achieve an ISO brightness of approximately 90.0%. The bleached soda pulps cooked to 17.5 and 10.6 kappa number showed similar refinability and resistance to drainage, but the tensile and burst index were highest for the 17.5 kappa pulp at beating energy consumptions in the range of 0-6 Wh. It was concluded that both 10.6 and 17.5 kappa pulps from elephant grass are suitable for the production of printing and writing paper grade pulps, but the highest kappa 17.5 pulp is more economically attractive given its highest pulping yield, despite the significantly increased of chemical demand for bleaching A produção de papel para impressão e escrita Grau de celulose a partir de capim-elefante.

The combined effect of food-simulating solutions, brushing and staining on color stability of composite resins

Science.gov (United States)

Silva, Tânia Mara Da; Sales, Ana Luísa Leme Simões; Pucci, Cesar Rogerio; Borges, Alessandra Bühler; Torres, Carlos Rocha Gomes

2017-01-01

Abstract Objective: This study evaluated the effect of food-simulating media associated with brushing and coffee staining on color stability of different composite resins. Materials and methods: Eighty specimens were prepared for each composite: Grandio SO (Voco), Amaris (Voco), Filtek Z350XT (3M/ESPE), Filtek P90 (3M/ESPE). They were divided into four groups according to food-simulating media for 7 days: artificial saliva (control), heptane, citric acid and ethanol. The composite surface was submitted to 10,950 brushing cycles (200 g load) in an automatic toothbrushing machine. The specimens were darkened with coffee solution at 37 °C for 24 h. After each treatment, color measurements were assessed by spectrophotometry, using CIE L*a*b* system. The overall color change (ΔE) was determined for each specimen at baseline (C1) and after the treatments (food-simulating media immersion/C2, brushing/C3 and dye solution/C4). Data were analyzed by two-way repeated measures ANOVA and Tukey’s tests (p composites (p = .001), time (p = .001) and chemical degradation (p = .002). The mean of ΔE for composites were: Z350XT (5.39)a, Amaris (3.89)b, Grandio (3.75)bc, P90 (3.36)c. According to food-simulating media: heptane (4.41)a, citric acid (4.24)a, ethanol (4.02)ab, artificial saliva (3.76)b. For the treatments: dye solution (4.53)a, brushing (4.26)a, after food-simulating media (3.52)b. Conclusions: The composite resin Filtek Z350XT showed significantly higher staining than all other composite resin tested. The immersion in heptane and citric acid produced the highest color alteration than other food-simulating media. The exposure of samples to brushing protocols and darkening in coffee solution resulted in significant color alteration of the composite resins. PMID:28642926

Recruitment of dental pulp cells by dentine and pulp extracellular matrix components.

Science.gov (United States)

Smith, J G; Smith, A J; Shelton, R M; Cooper, P R

2012-11-01

The present study aimed to determine whether dentine tissue and preparations of extracellular matrix (ECM) from pulp (pECM) and dentine (dECM), and breakdown products, influenced pulp cell migration. Chemotaxis transwell and agarose spot assays demonstrated that both dentine and pulp ECM molecules acted as chemoattractants for primary pulp cells. Chemoattractant activities of dECM and pECM were enhanced when subjected to acid and enzymatic breakdown, respectively. This enhanced activity following physiologically relevant breakdown may be pertinent to the disease environment. Pulp cell migration in response to dental ECMs was dependent on an active rho pathway. Recruited cells exhibited increased stem cell marker expression indicating that dental ECMs and their breakdown products selectively attract progenitor cells that contribute to repair processes. In conclusion, combined these results indicate that ECM molecules contribute to cell recruitment necessary for regeneration of the dentine-pulp complex after injury. Copyright © 2012 Elsevier Inc. All rights reserved.

Radiation -adsorption treatment of pesticides by using wood pulp and bagasse pulp

International Nuclear Information System (INIS)

Abd El-Aal, S.E.; Sokker, S.S.; Dessooki, A.M.

2005-01-01

Alkaline pulping of pulp wood and bagasse using sodium hydroxide resulted in the reduction of lignin from the wood and bagasse fibers and consequently increase adsorption of the pesticide pollutants to these fibers. Three different types of pesticides were used in this study namely, metalaxyl, dicloran and arelon. which were irradiated at a dose of 4 kGy before adsorption treatment.The results show that moderate adsorption was observed for all pesticides when adsorption was carried out without alkaline pulping and irradiation. This is due to the presence of lignin which retard the adsorption process. Batch sorption experiments at different pH values (3, 7, 9) for the retention of these pesticides by pulp wood and pulp bagasse fibers indicated that sorption is governed by the interaction of the ionized form of these compounds with the polyhydroxyl structure of cellulose. The study shows that alkaline pulping of pulpwood and bagasse improves its ability towards adsorption of the radiation degraded pesticide molecules

Active Nanomaterials to Meet the Challenge of Dental Pulp Regeneration.

Science.gov (United States)

Keller, Laetitia; Offner, Damien; Schwinté, Pascale; Morand, David; Wagner, Quentin; Gros, Catherine; Bornert, Fabien; Bahi, Sophie; Musset, Anne-Marie; Benkirane-Jessel, Nadia; Fioretti, Florence

2015-11-05

The vitality of the pulp is fundamental to the functional life of the tooth. For this aim, active and living biomaterials are required to avoid the current drastic treatment, which is the removal of all the cellular and molecular content regardless of its regenerative potential. The regeneration of the pulp tissue is the dream of many generations of dental surgeons and will revolutionize clinical practices. Recently, the potential of the regenerative medicine field suggests that it would be possible to achieve such complex regeneration. Indeed, three crucial steps are needed: the control of infection and inflammation and the regeneration of lost pulp tissues. For regenerative medicine, in particular for dental pulp regeneration, the use of nano-structured biomaterials becomes decisive. Nano-designed materials allow the concentration of many different functions in a small volume, the increase in the quality of targeting, as well as the control of cost and delivery of active molecules. Nanomaterials based on extracellular mimetic nanostructure and functionalized with multi-active therapeutics appear essential to reverse infection and inflammation and concomitantly to orchestrate pulp cell colonization and differentiation. This novel generation of nanomaterials seems very promising to meet the challenge of the complex dental pulp regeneration.

A randomized clinical trial on the use of medical Portland cement, MTA and calcium hydroxide in indirect pulp treatment.

Science.gov (United States)

Petrou, Marina Agathi; Alhamoui, Fadi Alhaddad; Welk, Alexander; Altarabulsi, Mohammed Basel; Alkilzy, Mohammed; H Splieth, Christian

2014-01-01

Studies on indirect pulp treatment (IPT) show varying success rates of 73 to 97 %. The necessity of re-opening the cavity and the question of the optimal capping material is still under debate. The aim of this prospective in vivo study was to compare the clinical and microbiological outcomes of mineral trioxide aggregate (MTA), medical Portland cement, and calcium hydroxide on the dentin-pulp complex of permanent and primary teeth treated with two-step IPT. In 86 regular patients (51 % men; 49 % women; age 17.2 years ±13.8), one deep carious lesion each was treated with incomplete caries removal, randomly selected capping with either calcium hydroxide (n = 31), medical Portland cement (29) or white MTA (26), and re-entry (6.3 months ±1.0). Clinical (color, humidity, and consistency of dentin) and microbiological (Lactobacilli/Mutans Strep. counts) parameters were recorded at the first and second treatment. The IPT had a high success rate of 90.3 % regardless of the material used (p = 0.72). The arrested lesions showed consistently darker, dry, and therefore, sclerotic dentine (p Portland cement. The findings of this study could promote the improvement of the IPT as a one-step treatment of deep carious lesions when the remaining demineralized dentin would be sealed with durable restorations.

PROTECTIVE COLORATION IN ANIMALS

OpenAIRE

Leena Lakhani

2017-01-01

Animals have range of defensive markings which helps to the risk of predator detection (camouflage), warn predators of the prey’s unpalatability (aposematism) or fool a predator into mimicry, masquerade. Animals also use colors in advertising, signalling services such as cleaning to animals of other species, to signal sexual status to other members of the same species. Some animals use color to divert attacks by startle (dalmatic behaviour), surprising a predator e.g. with eyespots or other f...

Material for radioactive protection

Science.gov (United States)

Taylor, R.S.; Boyer, N.W.

A boron containing burn resistant, low-level radiation protection material useful, for example, as a liner for radioactive waste disposal and storage, a component for neutron absorber, and a shield for a neutron source is described. The material is basically composed of borax in the range of 25 to 50%, coal tar in the range of 25 to 37.5%, with the remainder being an epoxy resin mix. A preferred composition is 50% borax, 25% coal tar and 25% epoxy resin. The material is not susceptible to burning and is about 1/5 the cost of existing radiation protection material utilized in similar applications.

Shellac/nanoparticles dispersions as protective materials for wood

Science.gov (United States)

Weththimuni, Maduka L.; Capsoni, Doretta; Malagodi, Marco; Milanese, Chiara; Licchelli, Maurizio

2016-12-01

Wood is a natural material that finds numerous and widespread applications, but is subject to different decay processes. Surface coating is the most common method used to protect wood against deterioration and to improve and stabilize its distinctive appearance. Shellac is a natural resin that has been widely used as a protective material for wooden artefacts (e.g. furniture, musical instruments), due to its excellent properties. Nevertheless, diffusion of shellac-based varnishes has significantly declined during the last decades, because of some limitations such as the softness of the coating, photo-degradation, and sensitivity to alcoholic solvents and to pH variations. In the present study, different inorganic nanoparticles were dispersed into dewaxed natural shellac and the resulting materials were investigated even after application on wood specimens in order to assess variations of the coating properties. Analyses performed by a variety of experimental techniques have shown that dispersed nanoparticles do not significantly affect some distinctive and desirable features of the shellac varnish such as chromatic aspect, film-forming ability, water repellence, and adhesion. On the other hand, the obtained results suggested that some weak points of the coating, such as low hardness and poor resistance to UV-induced ageing, can be improved by adding ZrO2 and ZnO nanoparticles, respectively.

Stability Study of Sunscreens with Free and Encapsulated UV Filters Contained in Plastic Packaging.

Science.gov (United States)

Briasco, Benedetta; Capra, Priscilla; Mannucci, Barbara; Perugini, Paola

2017-05-31

Sunscreens play a fundamental role in skin cancer prevention and in protection against photo-aging. UV filters are often photo-unstable, especially in relation to their vehicles and, being lipophilic substances, they are able to interact with plastic packaging. Finally, UV filter stability can be significantly affected by the routine use of the product at high temperatures. This work aims to study the stability of sunscreen formulations in polyethylene packaging. Butyl methoxydibenzoylmethane and octocrylene, both in a free form and as encapsulated filters were chosen as UV filters. Stability evaluations were performed both in the packaging and on the formulations. Moreover, a further two non-destructive techniques, near-infrared (NIR) spectroscopy and a multiple light scattering technique, were also used to evaluate the stability of the formulation. Results demonstrated clearly that all of the pack underwent significant changes in its elastic/plastic behavior and in external color after solar irradiation. From the evaluation of the extractable profile of untreated and treated packaging material an absorption of 2-phenoxyethanol and octocrylene were shown. In conclusion, the results highlighted clearly that a reduction of the UV filter in the formulation packed in high-density polyethylene/low-density polyethylene (HDPE/LDPE) material can occur over time, reducing the protective effect of the product when applied to the skin.

Influence of implant abutment material on the color of different ceramic crown systems.

Science.gov (United States)

Dede, Doğu Ömür; Armağanci, Arzu; Ceylan, Gözlem; Celik, Ersan; Cankaya, Soner; Yilmaz, Burak

2016-11-01

Ceramics are widely used for anterior restorations; however, clinical color reproduction still constitutes a challenge particularly when the ceramic crowns are used on titanium implant abutments. The purpose of this in vitro study was to investigate the effect of implant abutment material on the color of different ceramic material systems. Forty disks (11×1.5 mm, shade A2) were fabricated from medium-opacity (mo) and high-translucency (ht) lithium disilicate (IPS e.max) blocks, an aluminous ceramic (VITA In-Ceram Alumina), and a zirconia (Zirkonzahn) ceramic system. Disks were fabricated to represent 3 different implant abutments (zirconia, gold-palladium, and titanium) and dentin (composite resin, A2 shade) as background (11×2 mm). Disk-shaped composite resin specimens in A2 shade were fabricated to represent the cement layer. The color measurements of ceramic specimens were made on composite resin abutment materials using a spectrophotometer. CIELab color coordinates were recorded, and the color coordinates measured on composite resin background served as the control group. Color differences (ΔE 00 ) between the control and test groups were calculated. The data were analyzed with 2-way analysis of variance (ANOVA) and compared with the Tukey HSD test (α=.05). The ceramics system, abutment material, and their interaction were significant for ΔE 00 values (P2.25) were observed for lithium disilicate ceramics on titanium abutments (2.46-2.50). The ΔE 00 values of lithium disilicate ceramics for gold-palladium and titanium abutments were significantly higher than for other groups (P2.25) of an implant-supported lithium disilicate ceramic restoration may be clinically unacceptable if it is fabricated over a titanium abutment. Zirconia may be a more suitable abutment material for implant-supported ceramic restorations. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Vital Pulp Therapy of a Mature Molar with Concurrent Hyperplastic Pulpitis, Internal Root Resorption and Periradicular Periodontitis: A Case Report.

Science.gov (United States)

Asgary, Saeed; Kemal Çalışkan, Mehmet

2015-01-01

Vital pulp therapy (VPT) of permanent mature teeth is continuously ascertaining to be a more reliable endodontic treatment. The purpose of this case report was to describe successful VPT of a mature mandibular left first molar with concurrent hyperplastic pulpitis, internal root resorption and periradicular periodontitis in a 35-year-old male patient. After complete caries removal and access cavity preparation, the dental pulp was removed from the coronal third of the roots. To protect the remaining pulp, calcium-enriched mixture (CEM) cement was placed and adapted into the cavities; the tooth was then restored with amalgam. Six months after VPT, radiographic examination showed evidence of periradicular healing. Clinically, the tooth was functional without signs and symptoms of infection/inflammation. The successful outcome of this case suggests that diseased dental pulp (i.e. irreversible pulpitis) has the potential to heal after pulp protection with CEM biocement.

Vital Pulp Therapy of a Mature Molar with Concurrent Hyperplastic Pulpitis, Internal Root Resorption and Periradicular Periodontitis: A Case Report

Science.gov (United States)

Asgary, Saeed; Kemal Çalışkan, Mehmet

2015-01-01

Vital pulp therapy (VPT) of permanent mature teeth is continuously ascertaining to be a more reliable endodontic treatment. The purpose of this case report was to describe successful VPT of a mature mandibular left first molar with concurrent hyperplastic pulpitis, internal root resorption and periradicular periodontitis in a 35-year-old male patient. After complete caries removal and access cavity preparation, the dental pulp was removed from the coronal third of the roots. To protect the remaining pulp, calcium-enriched mixture (CEM) cement was placed and adapted into the cavities; the tooth was then restored with amalgam. Six months after VPT, radiographic examination showed evidence of periradicular healing. Clinically, the tooth was functional without signs and symptoms of infection/inflammation. The successful outcome of this case suggests that diseased dental pulp (i.e. irreversible pulpitis) has the potential to heal after pulp protection with CEM biocement. PMID:26523145

Pulp tissue in sex determination: A fluorescent microscopic study

Science.gov (United States)

Nayar, Amit; Singh, Harkanwal Preet; Leekha, Swati

2014-01-01

Aims: To determine and compare the reliability of pulp tissue in determination of sex and to analyze whether caries have any effect on fluorescent body test. Materials and Methods: This study was carried on 50 maxillary and mandibular teeth (25 male teeth and 25 female teeth), which were indicated for extraction. The teeth are categorized into 5 groups, 10 each (5 from males and 5 from females) on the basis of caries progression. The pulp cells are stained with quinacrine hydrochloride and observed with fluorescent microscope for fluorescent body. Gender is determined by identification of Y chromosome fluorescence in dental pulp. Results: Fluorescent bodies were found to be more in sound teeth in males as the caries increase the mean percentage of fluorescent bodies observed decreases in males. We also observed the fluorescent spots in females, and the value of the spot increases in female as the caries progresses, thereby giving false positive results in females. Conclusion: Sex determination by fluorescent staining of the Y chromosome is a reliable technique in teeth with healthy pulps or caries with enamel or up to half way of dentin. Teeth with caries involving pulp cannot be used for sex determination. PMID:25125912

EFFECTS OF ALKALINE PRE-IMPREGNATION AND PULPING ON MALAYSIA CULTIVATED KENAF (HIBISCUS CANNABINUS

Directory of Open Access Journals (Sweden)

Lin Suan Ang

2010-05-01

Full Text Available This study was carried out to identify an appropriate alkaline pulping condition for Malaysia cultivated kenaf (Hibiscus cannabinus L.. The chemical composition of the kenaf bast and core fibers, and also whole stalk with different growing time were examined prior to pulping attempts. The results of various soda-AQ pulping showed that the degree of carbohydrate degradation and delignification increased with the increase of active alkali and cooking temperature, but decreased with the increase of liquor to material (L:M ratio. The most satisfactory properties of pulp and handsheets from bast could be attained by employing soda-AQ pulping with 19.4% active alkali, 0.10% AQ, and L:M ratio of 7:1 cooked for 2 hours at 160˚C. Besides, it was also found that a mild alkaline pre-impregnation prior pulping improved the pulp viscosity and handsheets’ strength properties, especially the tensile index and folding endurance effectively. Moreover, among the three alkaline pulping processes—kraft, kraft-AQ, and soda-AQ—the results of pulp and handsheet properties showed that the soda-AQ pulp was comparable or even slightly of higher quality than the kraft pulps. Between the unbeaten bast and core soda-AQ handsheets, the strength properties of the core were higher than the bast, as the thin-walled core fibers exhibited much better conformability than the thick-walled bast fibers.

Investigation of dynamic of unconsolidated materials using two-color digital holography

Directory of Open Access Journals (Sweden)

Boileau J.-P.

2010-06-01

Full Text Available The paper presents a two-color digital holographic interferometer. The set-up is devoted to the study of the fundamental dynamic of unconsolidated materials. Optical configuration and algorithms to recover the optical phase of two-color digitally encoded holograms are described. The method is based on a spatial-color-multiplexing scheme in which holographic reconstruction is performed using adapted wavelength zero-padding and reconstructing distance. Experimental results are presented in the case of granular media excited in the frequency range 400Hz-3000Hz and exhibits the 3D movement.

Gamma irradiation of yellow and blue colorants in polystyrene packaging materials

International Nuclear Information System (INIS)

Komolprasert, V.; Diel, Todd; Sadler, G.

2006-01-01

The effect of 10- and 20-kGy gamma irradiation was studied on chromophtal yellow 2RLTS (Yellow 110-2, 3, 4, 5-tetrachloro-6-cyanobenzoic acid) and Irgalite Blue GBP (copper (II) phthalocyanine blue) colorants, which were added to polystyrene (PS) material used to package food prior to irradiation. Analytical results obtained suggest that irradiation did not generate any new chemicals in the PS polymer containing either yellow or blue colorant at a concentration of up to 1% (w/w). Both yellow and blue colorants are relatively stable to gamma irradiation

Betalain profile, phenolic content, and color characterization of different parts and varieties of Opuntia ficus-indica.

Science.gov (United States)

Cejudo-Bastante, María Jesús; Chaalal, Makhlouf; Louaileche, Hayette; Parrado, Juan; Heredia, Francisco J

2014-08-20

Three different varieties of Opuntia ficus-indica (R, red; Y, yellow; RY, red-yellow) have been considered in this study. Attention was focused on differential tristimulus colorimetry and on the analysis of individual betalains (HPLC-DAD-ESI-ToF-MS) and phenolic content, scarcely previously reported in these kinds of samples. The importance of this research stems from the elucidation of the parts and varieties of cactus pear more optimal for use as natural colorants and sources of phenolics and betalains. Thus, the RY pulp was appropriate to obtain colorants with high color intensity (C*(ab) = 66.5), whereas the whole Y fruit and R pulp reached powerful and stable yellow and red colors, respectively (C*(ab)/h(ab), 57.1/84.7 and 61.1°/81.8°). This choice was also based on the visually appreciable differences (ΔE*(ab) > 5) among samples, mainly quantitative (%Δ(2)L, %Δ(2)C). In addition, seeds of all Opuntia varieties showed significantly (p < 0.05) similar phenolic content (around 23.3 mg/g) and color characteristics.

Microencapsulation of pequi pulp oil by complex coacervation

Directory of Open Access Journals (Sweden)

Priscilla Narciso Justi

2018-04-01

Full Text Available Abstract Pequi pulp oil, Caryocar brasiliense, is rich in carotenoids, antioxidant compound easily oxidized by the presence of heat, light and oxygen. In order to improve its stability, pequi oil was microencapsulated by complex coacervation using gelatin and Arabic gum as encapsulating agents. Twenty formulations were prepared using a 23 central composite rotational design. The influence of temperature, stirring velocity and core material in the oil coacervation were evaluated, aiming to preserve carotenoids present in the oil. The best yield values and carotenoids content were obtained at the midpoint of the design (7.5g core, 15.000rpm and 50°C. Particles showed asymmetric distribution, with diameter ranging from 15 to 145 µm and the efficiency of the encapsulation process, obtained by the retention of oil in the microcapsule, ranged from 66.58 to 96.50%, thus demonstrating the encapsulation efficiency of this method.

Effects of electrolytes and surfactants on the morphology and stability of advanced silver nano-materials

Energy Technology Data Exchange (ETDEWEB)

Obaid, Abdullah Yousif; AL-Thabaiti, Shaeel Ahmed; El-Mossalamy, E.H. [Department of Chemistry, Faculty of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21413 (Saudi Arabia); Hussain, Javed Ijaz [Nano-science Research Lab, Department of Chemistry, Jamia Millia Islamia (Central University), New Delhi 110 025 (India); Khan, Zaheer, E-mail: drkhanchem@yahoo.co.in [Nano-science Research Lab, Department of Chemistry, Jamia Millia Islamia (Central University), New Delhi 110 025 (India)

2013-03-15

Highlights: ► Stoichiometric ratio of S{sub 2}O{sub 3}{sup 2−} and Ag{sup +} ions are responsible to the formation of prefect transparent yellow colored silver sol. ► Higher S{sub 2}O{sub 3}{sup 2−} concentrations has damping effect. ► Head group of the surfactants and nature of the electrolytes have significant effect on the stability of silver nanoparticles. - Abstract: The impact of electrolytes, stabilizing and/or capping agents on morphology of colloidal silver nano-materials (AgNPs) has been studied spectroscopically. Sodium thiosulfate acts as reducing-, stabilizing- and damping-agents. Stoichiometric ratios of S{sub 2}O{sub 3}{sup 2−} and Ag{sup +} ions were responsible to the formation stable and prefect transparent dark yellow colored AgNPs. The S{sub 2}O{sub 3}{sup 2−}-stabilized AgNPs were significantly more stable in inorganic electrolytes (NaNO{sub 3}, Na{sub 2}SO{sub 4}, Na{sub 2}CO{sub 3} and KBr). S{sub 2}O{sub 3}{sup 2−} is adsorbed more strongly than the used other anions. The addition of cetyltrimethylammonium bromide (CTAB) and sodium dodecylsulfate (SDS) has significant effects on the absorbance of S{sub 2}O{sub 3}{sup 2−}-stabilized AgNPs which can be rationalized in terms of electrostatic attraction and repulsion between the adsorbed S{sub 2}O{sub 3}{sup 2−} ions on to the surface of AgNPs and cationic and/or anionic head groups of used surfactants, respectively. Transmission electron microscopy images suggest that AgNPs are polydispersed, spherical and exhibiting an interesting irregular morphology.

RELATIONSHIP BETWEEN CRYSTALLINE STRUCTURE AND OPTICAL PROPERTIES OF WHEAT (Triticum aestevum L. STRAW SODA-OXYGEN PULP

Directory of Open Access Journals (Sweden)

Esat Gümüşkaya

2003-04-01

Full Text Available In this study; pulp was produced with soda-oxygen process by using wheat (Triticum aestevum L. straw as raw material and this pulp bleached with hypocholoride (H and peroxyde (P stages. It was found that crystalline properties of unbleached and bleached pulp samples increased by removing amorphous components. In addition, paper sheets made from unbleached and bleached soda-oxygen pulp and determined their optical properties. Consequently; while crystalline properties of pulp samples was rising with HP bleaching, it was determined that optical properties of paper sheets improved with bleaching.

40 CFR 63.443 - Standards for the pulping system at kraft, soda, and semi-chemical processes.

Science.gov (United States)

2010-07-01

... Paper Industry § 63.443 Standards for the pulping system at kraft, soda, and semi-chemical processes. (a... operator of each pulping system using a semi-chemical or soda process subject to the requirements of this... kraft, soda, and semi-chemical processes. 63.443 Section 63.443 Protection of Environment ENVIRONMENTAL...

Water requirements of the pulp and paper industry

Science.gov (United States)

Mussey, Orville D.

1955-01-01

are manufacturing sulfate pulp; because of the antipollution laws, many sulfite-pulp mills are being converted to sulfate-pulp mills. The waste from the manufacture of a ton of sulfate pulp is much more readily disposed of than that from a ton of sulfite pulp. Pulp mills are located near the source of raw material, which means that they are located in the eastern half of the United States and in the Pacific Northwest. It is advantageous for paper mills to be located close to a market and therefore a large number of paper mills are in the northeastern section of the United States from Minnesota to Maine. However, much of the coarser paper, which will ship well, is produced close to the pulp mills. The entire process of making paper from pulpwood, with special reference to water use is briefly described to provide an understanding of how the water is used and reused.

Preparação de um material de referência certificado para controle de agrotóxicos em hortifrutigranjeiros: estudo da estabilidade Preparation of a certified reference material for pesticide control in the cultivation fruits and vegetables: a stability study

Directory of Open Access Journals (Sweden)

Maria Helena Wohlers Morelli Cardoso

2010-06-01

Full Text Available Neste trabalho são apresentados os resultados dos estudos de estabilidade referentes à produção de um material de referência certificado. Foram avaliados níveis residuais de concentração dos agrotóxicos γ-HCH, fenitrotiona, clorpirifós e procimidona em polpa de tomate. A pasteurização e a irradiação gama foram empregadas à polpa de tomate, visando manter a integridade da amostra candidata a material de referência. A polpa foi preparada e dividida em duas partes. Cada parte foi fortificada com os referidos agrotóxicos na faixa de concentração de 0,1 a 0,2 mg.kg-1. Uma das partes foi submetida à pasteurização a 90 °C por 4 minutos e a outra parte foi irradiada com dose de 2,0 kGy depois de homogeneizada. A estabilidade e a incerteza da amostra, correspondente ao período de tempo avaliado, foram determinadas através da análise de regressão em conjunto com a ANOVA. Os resultados indicaram que ambos os procedimentos de preparo da amostra são adequados para a conservação da polpa de tomate fortificada com os quatro agrotóxicos, com vantagem para o tratamento por irradiação com a dose de 2,0 kGy.This research presents the results of stability studies regarding the production of certified reference materials. The residual concentration levels of four pesticides, namely γ-HCH, fenitrothion, chlorpyrifos, and procymidone were investigated. Pasteurization combined with gamma irradiation was used to maintain the integrity of the mixture tested as a reference material candidate. The pulp was prepared and split into two parts. Each part was then spiked with those pesticides in the concentration range of 0.1 to 0.2 mg.kg-1 in tomato pulp. One of them was submitted to pasteurization at 90 °C for 4 minutes after being homogenized, and the other was irradiated with a gamma dose of 2.0 kGy. The material stability and the corresponding uncertainty during the period of time evaluated were determined using regression analysis and

High-Thermal- and Air-Stability Cathode Material with Concentration-Gradient Buffer for Li-Ion Batteries.

Science.gov (United States)

Shi, Ji-Lei; Qi, Ran; Zhang, Xu-Dong; Wang, Peng-Fei; Fu, Wei-Gui; Yin, Ya-Xia; Xu, Jian; Wan, Li-Jun; Guo, Yu-Guo

2017-12-13

Delivery of high capacity with high thermal and air stability is a great challenge in the development of Ni-rich layered cathodes for commercialized Li-ion batteries (LIBs). Herein we present a surface concentration-gradient spherical particle with varying elemental composition from the outer end LiNi 1/3 Co 1/3 Mn 1/3 O 2 (NCM) to the inner end LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA). This cathode material with the merit of NCM concentration-gradient protective buffer and the inner NCA core shows high capacity retention of 99.8% after 200 cycles at 0.5 C. Furthermore, this cathode material exhibits much improved thermal and air stability compared with bare NCA. These results provide new insights into the structural design of high-performance cathodes with high energy density, long life span, and storage stability materials for LIBs in the future.

The physical protection of nuclear material

International Nuclear Information System (INIS)

1989-12-01

A Technical Committee on Physical Protection of Nuclear Material met in April-May 1989 to advise on the need to update the recommendations contained in document INFCIRC/225/Rev.1 and on any changes considered to be necessary. The Technical Committee indicated a number of such changes, reflecting mainly: the international consensus established in respect of the Convention on the Physical Protection of Nuclear Material; the experience gained since 1977; and a wish to give equal treatment to protection against the theft of nuclear material and protection against the sabotage of nuclear facilities. The recommendations presented in this IAEA document reflect a broad consensus among Member States on the requirements which should be met by systems for the physical protection of nuclear materials and facilities. 1 tab

Different Anthocyanin Profiles of the Skin and the Pulp of Yan73 (Muscat Hamburg × Alicante Bouschet Grape Berries

Directory of Open Access Journals (Sweden)

Chang-Qing Duan

2010-03-01

Full Text Available Yan73 is a “teinturier” red wine variety cultivated in China and used in winemaking to strengthen red wine color. Here, the anthocyanin profile in both the skin and pulp of this grape variety was analyzed by HPLC-MS. The results showed that 18 anthocyanins were detected in both the skin and the pulp, and pelargonidin-3-O-glucoside, an anthocyanin compound hardly detected in most other Vitis viniferaberries, was found. However, the contents of individual anthocyanins in the skin and the pulp were significantly different. Compared with the skin, the pulp exhibited much lower ratio of 3’,5’-substituted to 3’-substituted anthocyanins and much higher ratio of methoxylation of anthocyanin B-ring to non methoxylation, and with regard to the aromatic acylated and aliphatic acylated anthocyanins, both their contents in the skin are higher than in the pulp. The findings will provide some new insight for the tissue-specific expression and regulation of the genes involving in anthocyanin biosynthesis in grape berries.

Effect of Baobab ( Adansonia digitata L.) Fruit Pulp Drink on Iron ...

African Journals Online (AJOL)

Objective: To determine the effect of consuming baobab fruit pulp drink with the diet on iron status of school children. Materials and Methods: Baobab fruit pulp was scrapped from the seeds and mixed with water in the ratio of 1:2 (w/v) to produce a refreshing drink. One hundred and forty two school children 6-8 yrs involved ...

A modified efficient method for dental pulp stem cell isolation

Directory of Open Access Journals (Sweden)

Maryam Raoof

2014-01-01

Full Text Available Background: Dental pulp stem cells can be used in regenerative endodontic therapy. The aim of this study was to introduce an efficient method for dental pulp stem cells isolation. Materials and Methods: In this in-vitro study, 60 extracted human third molars were split and pulp tissue was extracted. Dental pulp stem cells were isolated by the following three different methods: (1 digestion of pulp by collagenase/dispase enzyme and culture of the released cells; (2 outgrowth of the cells by culture of undigested pulp pieces; (3 digestion of pulp tissue pieces and fixing them. The cells were cultured in minimum essential medium alpha modification (αMEM medium supplemented with 20% fetal bovine serum(FBS in humid 37°C incubator with 5% CO 2 . The markers of stem cells were studied by reverse transcriptase polymerase chain reaction (PCR. The student t-test was used for comparing the means of independent groups. P <0.05 was considered as significant. Results: The results indicated that by the first method a few cell colonies with homogenous morphology were detectable after 4 days, while in the outgrowth method more time was needed (10-12 days to allow sufficient numbers of heterogeneous phenotype stem cells to migrate out of tissue. Interestingly, with the improved third method, we obtained stem cells successfully with about 60% efficiency after 2 days. The results of RT-PCR suggested the expression of Nanog, Oct-4, and Nucleostemin markers in the isolated cells from dental pulps. Conclusion: This study proposes a new method with high efficacy to obtain dental pulp stem cells in a short time.

Melatonin attenuates inflammation of acute pulpitis subjected to dental pulp injury

Science.gov (United States)

Li, Ji-Guo; Lin, Jia-Ji; Wang, Zhao-Ling; Cai, Wen-Ke; Wang, Pei-Na; Jia, Qian; Zhang, An-Sheng; Wu, Gao-Yi; Zhu, Guo-Xiong; Ni, Long-Xing

2015-01-01

supplementation with melatonin may have a protective effect on AP by modulating TLR4/NF-ĸB signaling in the pulp and in pulp cells. PMID:25755829

Can Dental Pulp Calcification Predict the Risk of Ischemic Cardiovascular Disease?

Directory of Open Access Journals (Sweden)

Leila Khojastepour

2013-01-01

Full Text Available Objective: To report the association of pulp calcification with that of cardiovascular disease (CVD using digital panoramic dental radiographs.Materials and Methods: Digital panoramic radiographs of patients referred from the angiography department were included if the patient was under 55 years old and had non-restored or minimally restored molars and canines. An oral and maxillofacial radiologist evaluated the images for pulpal calcifications in the selected teeth. The sensitivity, specificity, positive predictive value and negative predictive value of panoramic radiography in predicting CVD were calculated.Results: Out of 122 patients who met the criteria, 68.2% of the patients with CVD had pulp chamber calcifications. Pulp calcification in panoramic radiography had a sensitivity of 68.9% to predict CVD.Conclusion: This study demonstrates that patients with CVD show an increased incidence of pulp calcification compared with healthy patients. The findings suggest that pulp calcification on panoramic radiography may have possibilities for use in CVD screening.

Application of thermophilic enzymes and water jet system to cassava pulp.

Science.gov (United States)

Chaikaew, Siriporn; Maeno, Yuka; Visessanguan, Wonnop; Ogura, Kota; Sugino, Gaku; Lee, Seung-Hwan; Ishikawa, Kazuhiko

2012-12-01

Co-production of fermentable sugars and nanofibrillated cellulose from cassava pulp was achieved by the combination of thermophilic enzymes (endoglucanase, β-glucosidase, and α-amylase) and a new atomization system (Star Burst System; SBS), which employs opposing water jets. The SBS represents a key technology for providing cellulose nanofibers and improving the enzymatic saccharification of cassava pulp. Depending on the enzymes used, the production of glucose from cassava pulp treated with the SBS was 1.2- to 2.5-fold higher than that from pulp not treated with the SBS. Nanofibrillated cellulose with the gel-like property in suspension was produced (yield was over 90%) by α-amylase treatment, which completely released trapped starch granules from the fibrous cell wall structure of cassava pulp pretreated with the SBS. The SBS provides an environmentally low-impact pretreatment system for processing biomass material into value-added products. Copyright © 2012 Elsevier Ltd. All rights reserved.

Color stability of maxillofacial silicone with nanoparticle pigment and opacifier submitted to disinfection and artificial aging.

Science.gov (United States)

Filié Haddad, Marcela; Coelho Goiato, Marcelo; Micheline Dos Santos, Daniela; Moreno, Amália; Filipe D'almeida, Nuno; Alves Pesqueira, Aldiéris

2011-09-01

The purpose of this study was to evaluate the color stability of a maxillofacial elastomer with the addition of a nanoparticle pigment and∕or an opacifier submitted to chemical disinfection and artificial aging. Specimens were divided into four groups (n = 30): group I: silicone without pigment or opacifier, group II: ceramic powder pigment, group III: Barium sulfate (BaSO(4)) opacifier, and group IV: ceramic powder and BaSO(4) opacifier. Specimens of each group (n = 10) were disinfected with effervescent tablets, neutral soap, or 4% chlorhexidine gluconate. Disinfection was done three times a week during two months. Afterward, specimens were submitted to different periods of artificial aging. Color evaluation was initially done, after 60 days (disinfection period) and after 252, 504, and 1008 h of artificial aging with aid of a reflection spectrophotometer. Data were analyzed by three-way ANOVA and Tukey test (α = 0.05). The isolated factor disinfection did not statistically influence the values of color stability among groups. The association between pigment and BaSO(4) opacifier (GIV) was more stable in relationship to color change (△E). All values of △E obtained, independent of the disinfectant and the period of artificial aging, were considered acceptable in agreement with the norms presented in literature.

Uso de novos materiais para o capeamento pulpar (hidroxiapatita - HAp e fosfato tricálcico - β-TCP The use of new materials for pulp capping (hydroxyapatite - HAp and tricalcium phosphate - β-TCP

Directory of Open Access Journals (Sweden)

C. S. Delfino

2010-12-01

Full Text Available O capeamento pulpar é uma medida importante e muito usada no cotidiano da prática odontológica e, quando realizado de forma consciente, baseado em um bom diagnóstico da condição pulpar no momento da exposição, pode prevenir o dente de sofrer uma intervenção endodôntica. Além do hidróxido de cálcio, outros materiais vêm sendo testados quanto a sua ação em promover o reparo pulpar pela formação de ponte de dentina, após capeamento pulpar direto. Uma das alternativas de materiais viáveis para o capeamento pulpar são as cerâmicas à base de fosfatos de cálcio, destacando-se a hidroxiapatita (HAp e o fosfato tricálcico (β-TCP. Estes materiais não promovem a formação de área necrótica, característica da utilização do hidróxido de cálcio, são biocompatíveis e favorecem o reparo do tecido pulpar. Para avaliar os efeitos desses materiais no capeamento pulpar foi realizada esta revisão de literatura, abordando desde a resposta do tecido pulpar, até o protocolo para o uso clínico.Pulp capping is an important measure and one with a high rate of use in daily dental practice, and when it is conscientiously performed, based on good diagnosis of the pulp condition at the time of its exposure, it may prevent the tooth from requiring endodontic intervention. In addition to calcium hydroxide, other materials have been tested with regard to their action in promoting pulp repair by the formation of a dentin bridge after direct pulp capping. Some of the feasible alternative materials for pulp capping are calcium phosphate-based ceramics, with hydroxyapatite (HAp and tricalcium phosphate (β-TCP being outstanding. These materials do not promote formation of a necrotic area, characteristic of the use of calcium hydroxide, are biocompatible and favor pulp tissue repair. To evaluate the effects of these materials on pulp capping, this literature review was conducted, the approach being wide ranging in scope, from pulp response

Color stability of ceramic brackets immersed in potentially staining solutions.

Science.gov (United States)

Guignone, Bruna Coser; Silva, Ludimila Karsbergen; Soares, Rodrigo Villamarim; Akaki, Emilio; Goiato, Marcelo Coelho; Pithon, Matheus Melo; Oliveira, Dauro Douglas

2015-01-01

To assess the color stability of five types of ceramic brackets after immersion in potentially staining solutions. Ninety brackets were divided into 5 groups (n = 18) according to brackets commercial brands and the solutions in which they were immersed (coffee, red wine, coke and artificial saliva). The brackets assessed were Transcend (3M/Unitek, Monrovia, CA, USA), Radiance (American Orthodontics, Sheboygan, WI, USA), Mystique (GAC International Inc., Bohemia, NY, USA) and Luxi II (Rocky Mountain Orthodontics, Denver, CO, USA). Chromatic changes were analyzed with the aid of a reflectance spectrophotometer and by visual inspection at five specific time intervals. Assessment periods were as received from the manufacturer (T0), 24 hours (T1), 72 hours (T2), as well as 7 days (T3) and 14 days (T4) of immersion in the aforementioned solutions. Results were submitted to statistical analysis with ANOVA and Bonferroni correction, as well as to a multivariate profile analysis for independent and paired samples with significance level set at 5%. The duration of the immersion period influenced color alteration of all tested brackets, even though these changes could not always be visually observed. Different behaviors were observed for each immersion solution; however, brackets immersed in one solution progressed similarly despite minor variations. Staining became more intense over time and all brackets underwent color alterations when immersed in the aforementioned solutions.

A theranostic dental pulp capping agent with improved MRI and CT contrast and biological properties.

Science.gov (United States)

Mastrogiacomo, S; Güvener, N; Dou, W; Alghamdi, H S; Camargo, W A; Cremers, J G O; Borm, P J A; Heerschap, A; Oosterwijk, E; Jansen, J A; Walboomers, X F

2017-10-15

Different materials have been used for vital dental pulp treatment. Preferably a pulp capping agent should show appropriate biological performance, excellent handling properties, and a good imaging contrast. These features can be delivered into a single material through the combination of therapeutic and diagnostic agents (i.e. theranostic). Calcium phosphate based composites (CPCs) are potentially ideal candidate for pulp treatment, although poor imaging contrast and poor dentino-inductive properties are limiting their clinical use. In this study, a theranostic dental pulp capping agent was developed. First, imaging properties of the CPC were improved by using a core-shell structured dual contrast agent (csDCA) consisting of superparamagnetic iron oxide (SPIO) and colloidal gold, as MRI and CT contrast agent respectively. Second, biological properties were implemented by using a dentinogenic factor (i.e. bone morphogenetic protein 2, BMP-2). The obtained CPC/csDCA/BMP-2 composite was tested in vivo, as direct pulp capping agent, in a male Habsi goat incisor model. Our outcomes showed no relevant alteration of the handling and mechanical properties (e.g. setting time, injectability, and compressive strength) by the incorporation of csDCA particles. In vivo results proved MRI contrast enhancement up to 7weeks. Incisors treated with BMP-2 showed improved tertiary dentin deposition as well as faster cement degradation as measured by µCT assessment. In conclusion, the presented theranostic agent matches the imaging and regenerative requirements for pulp capping applications. In this study, we combined diagnostic and therapeutic agents in order to developed a theranostic pulp capping agent with enhanced MRI and CT contrast and improved dentin regeneration ability. In our study we cover all the steps from material preparation, mechanical and in vitro characterization, to in vivo study in a goat dental model. To the best of our knowledge, this is the first time that a

Effect of preheat repetition on color stability of methacrylate- and silorane-based composite resins.

Science.gov (United States)

Abed Kahnamouei, Mehdi; Gholizadeh, Sarah; Rikhtegaran, Sahand; Daneshpooy, Mehdi; Kimyai, Soodabeh; Alizadeh Oskoee, Parnian; Rezaei, Yashar

2017-01-01

Background. The aim of this study was to investigate the effect of preheating methacrylate- and silorane-based composite resins on their color stability up to 40 times at 55‒60°C. Methods. Seventy-six methacrylate and silorane-based composite resin samples, with a diameter of 10 mm and a height of 2 mm, were divided into 4 groups (n=19). After the samples were prepared, their color parameters were determined using a reflective spectrophotometer. The composite resin samples were separately stored in a solution of tea for 40 consecutive days. Then the samples underwent a color determination procedure again using a spectrophotometer and color changes were recorded. Finally two-way ANOVA was used to study the effect of composite temperature on its staining (Pcomposite resin samples compared to non-heated samples at P=0.005 and P=0.029 for silorane-based and Z250 composite resin samples, respectively. Results. Both composite resin type (P=0.014) and preheating (Pcomposite resin samples, up to 55‒60°C for 40 rounds, resulted in more color changes compared with unheated composite resin samples. After storage in a solution of tea the color change rate in the composite resin samples of silorane-based was higher than the Z250 composite resin samples.

Stabilization of Inverse Miniemulsions by Silyl-Protected Homopolymers

Directory of Open Access Journals (Sweden)

Sarah Wald

2016-08-01

Full Text Available Inverse (water-in-oil miniemulsions are an important method to encapsulate hydrophilic payloads such as oligonucleotides or peptides. However, the stabilization of inverse miniemulsions usually requires block copolymers that are difficult to synthesize and/or cannot be easily removed after transfer from a hydrophobic continuous phase to an aqueous continuous phase. We describe here a new strategy for the synthesis of a surfactant for inverse miniemulsions by radical addition–fragmentation chain transfer (RAFT polymerization, which consists in a homopolymer with triisopropylsilyl protecting groups. The protecting groups ensure the efficient stabilization of the inverse (water-in-oil, w/o miniemulsions. Nanocapsules can be formed and the protecting group can be subsequently cleaved for the re-dispersion of nanocapsules in an aqueous medium with a minimal amount of additional surfactant.

Zirconia-based colors for ceramic glazes

International Nuclear Information System (INIS)

Eppler, R.A.

1977-01-01

The history of color development for use in ceramic glazes is outlined. The most significant modern development is based on zirconia and zircon. These materials have gained increasing acceptance in the industry since their introduction in the late 1950's and early 1960's, due to their superior stability during firing of the glaze

Active Nanomaterials to Meet the Challenge of Dental Pulp Regeneration

Directory of Open Access Journals (Sweden)

Laetitia Keller

2015-11-01

Full Text Available The vitality of the pulp is fundamental to the functional life of the tooth. For this aim, active and living biomaterials are required to avoid the current drastic treatment, which is the removal of all the cellular and molecular content regardless of its regenerative potential. The regeneration of the pulp tissue is the dream of many generations of dental surgeons and will revolutionize clinical practices. Recently, the potential of the regenerative medicine field suggests that it would be possible to achieve such complex regeneration. Indeed, three crucial steps are needed: the control of infection and inflammation and the regeneration of lost pulp tissues. For regenerative medicine, in particular for dental pulp regeneration, the use of nano-structured biomaterials becomes decisive. Nano-designed materials allow the concentration of many different functions in a small volume, the increase in the quality of targeting, as well as the control of cost and delivery of active molecules. Nanomaterials based on extracellular mimetic nanostructure and functionalized with multi-active therapeutics appear essential to reverse infection and inflammation and concomitantly to orchestrate pulp cell colonization and differentiation. This novel generation of nanomaterials seems very promising to meet the challenge of the complex dental pulp regeneration.

Challenges of stem cell-based pulp and dentin regeneration: a clinical perspective.

Science.gov (United States)

Huang, George T-J; Al-Habib, Mey; Gauthier, Philippe

2013-03-01

There are two types of approaches to regenerate tissues: cell-based and cell-free. The former approach is to introduce exogenous cells into the host to regenerate tissues, and the latter is to use materials other than cells in an attempt to regenerate tissues. There has been a significant advancement in stem cell-based pulp and dentin regeneration research in the past few years. Studies in small and large animals have demonstrated that pulp/dentin-like tissues can be regenerated partially or completely in the root canal space with apical openings of 0.7-3.0 mm using dental pulp stem cells, including stem cells from apical papilla (SCAP) and subpopulations of pulp stem cells. Bone marrow mesenchymal stem cells (BMMSCs) and adipose tissue-derived MSCs (ADMSCs) have also been shown to regenerate pulp-like tissue. In contrast, the cell-free approach has not produced convincing evidence on pulp regeneration. However, one crucial concept has not been considered nor defined in the field of pulp/dentin regeneration and that is the critical size defect of dentin and pulp. Without such consideration and definition, it is difficult to predict or anticipate the extent of cell-free pulp regeneration that would occur. By reasoning, cell-free therapy is unlikely to regenerate an organ/tissue after total loss. Similarly, after a total loss of pulp, it is unlikely to regenerate without using exogenously introduced cells. A cell homing approach may provide a limited amount of tissue regeneration. Although stem cell-based pulp/dentin regeneration has shown great promise, clinical trials are difficult to launch at present. This article will address several issues that challenge and hinder the clinical applications of pulp/dentin regeneration which need to be overcome before stem cell-based pulp/dentin regeneration can occur in the clinic.

Characterization of Cypress Wood for Kraft Pulp Production

Directory of Open Access Journals (Sweden)

António J. A. Santos

2014-06-01

Full Text Available Wood samples of Cupressus arizonica, C. lusitanica, and C. sempervirens were evaluated for chemical, anatomical, and pulp characteristics as raw material for pulp production. Two 17-year-old trees per species were harvested, and wood samples were taken at a height of 2 m. Wood chips from Pinus pinaster (Portugal and P. sylvestris (Finland were used as references. C. arizonica differed from C. lusitanica and C. sempervirens with significantly lower (p < 0.05 tracheid diameter and wall thickness in the earlywood. The total extractives contents were 3.9%, 3.3%, and 2.5% for C. lusitanica, C. sempervirens, and C. arizonica, respectively, lower than the 5.1% for P. pinaster and 4.5% for P. sylvestris. Klason lignin content ranged from 33.0 to 35.6%, higher than the 28.0 to 28.7% for the pinewoods. The kraft pulp yields for C. arizonica, C. lusitanica, and C. sempervirens were 37.7%, 36.7%, and 38.7%, respectively, with kappa numbers of 32.0, 31.6, and 28.7, respectively; the yield values were 40.8% and 42.8%, with kappa numbers of 23.4 and 21.0, for P. pinaster and P. sylvestris, respectively. The cypress species are clearly different from pine in relation to wood pulping behavior. Among the cypress, C. sempervirens provided the best pulping results.

Effect of gamma radiation from 60C in conservation and quality of pepper fresh and pulp

International Nuclear Information System (INIS)

Milagres, Regina Celia Rodrigues de Miranda

2014-01-01

Capsicum peppers are among the most used and most valued seasoning spices in the world. They are highly susceptible to post harvest decay, therefore the use of irradiation may contribute to conservation of this fruit which has significant nutritional, economic and social value. Were evaluated the effects of gamma radiation of 60 Co in increasing the shelf-life and preservation of quality of pepper 'Dedo-de-moca' (Capsicum baccatum var. Pendulum) fresh and pulp associated or not with another conservation methods. Gamma radiation doses were investigated of 0,25; 0,50; 0,75; 1,00; 1,25; 1,50; 2,00 e 3,00 kGy in fresh fruit and 1,50; 2,00; 3,00; 4,50 e 6,00 kGy in pepper pulp. The use of laboratory pasteurization (85°C/3min), the addition of citric acid (5%) and 5% NaCl were also investigated in the pepper pulp. The samples were stored at 5 °C and or 25 °C. Were performed analysis: visual (disease incidence, turgidity and color); bioactive compounds (carotenoids, capsaicinoids, antioxidant capacity and phenolic compounds); physicochemical (Weight loss, firmness, soluble solids (SS), pH, titratable acidity (TA), ratio, color and moisture); respiratory rate and ethylene production; proximate composition (moisture, soluble and insoluble fiber, ash, protein, ether extract, total and available carbohydrate); microbiological contamination (mesophilic aerobic microorganisms, coliforms at 45 °C, Salmonella spp. and yeasts and molds) and sensory (acceptance test, difference test and paired preference). Radiation doses between 0.25 and 3.00 kGy were not effective to increase shelf-life and maintain fresh pepper quality during storage. There was increased intensity of red color, of incidence of disease, decreased turgidity and changes in physical, chemical and nutritional parameters. In pulp, the doses of gamma radiation of 4.50 and 6.00 kGy and the addition of 5% NaCl no changing sensory attributes, physical-chemical and bioactive compounds. Only the antioxidant

EVALUACIÓN DEL COLOR DURANTE EL ALMACENAMIENTO DE LA PULPA DE BANANO VERDE IMPREGNADA AL VACÍO CON SOLUCIONES ANTIPARDEANTES AVALIAÇÂO DA COR NO ARMAZENAMENTO DA POLPA DE BANANA VERDE IMPREGNADA A VACUUM USANDO SOLUÇÔES PARA EVITAR O PARDEAMENTO COLOR EVALUATION DURING STORAGE OF GREEN BANANAS PULP IMPREGNATED WITH ANTIBROWNNING SOLUTIONS UNDER VACCUM

Directory of Open Access Journals (Sweden)

MISAEL CORTÉS R

2011-12-01

Full Text Available La impregnación al vacío es la técnica aplicada por la ingeniería de matrices, como mecanismo de incorporación de soluciones al interior de las matrices alimentarias. Se evaluó la evolución del color en la pulpa de banano verde (PBV (Musa cavendish a diferentes condiciones de almacenamiento: tiempo (0, 3, 6, 9, 12 y 15 días, temperatura (4, 20 y 30°C y empaque, con vacío (CV y sin vacío (SV; bajo tratamientos con sulfitos (500, 1000, 1500 mg/kg PBV y de la interacción antioxidante (60, 90, 120 mg/100 g PBV acidulantes (50, 150, 250 mg/100 g PBV. Los parámetros de color se evaluaron en el espacio CIEL*a*b*, en términos de luminosidad (L* y cromaticidad a* y b*. El ANOVA presentó diferencias estadísticas significativas (p A impregnaçáo a vacuo é é uma técnica usada pela engenharia de matrizes como um meio de incorporar soluçóes na matriz dos alimentos. Neste trabalho foram avaliados a evoluçáo da cor da polpa da banana verde (PBV (Musa cavendish para diferentes condiçóes de armazenamento: tempo (0, 3, 6, 9, 12 e 15 dias, temperatura (4, 20 e 30 °C e condiçóes de embalagem (com vácuo (CV e sem vacuo (SV, sob tratamento com sulfitos (500, 1000, 1500 mg/kg de PBV e interaçáo antioxidante (60, 90, 120 mg/100 g PBV e acidulantes (50, 150, 250 mg/100 g PBV. Os parâmetros de cor foram avaliados no sistema CIÉL*a*b*, em termos de luminosidade (L* e cromaticidade (a*,b*. A análise de variância (ANOVA apresentou diferenças significativas (p Vacuum impregnation is a technique applied by matrix engineering as the mechanism to incorporate the solutions to the interior of an alimentary matrix. The development of the color of the pulp of unripe Banana (PUB (Musa cavendish was evaluated in different storage conditions: Time 0, 3, 6, 9, 12, and 15 days, Temperature 4, 20, and 30°C, packed with vacuum (WV and without vacuum (NV under sulfite treatment (500, 1000, 1500 mg/kg PUB and the antioxidant interaction (60, 90, 120 mg

Characterization of Coronal Pulp Cells and Radicular Pulp Cells in Human Teeth.

Science.gov (United States)

Honda, Masaki; Sato, Momoko; Toriumi, Taku

2017-09-01

Dental pulp has garnered much attention as an easily accessible postnatal tissue source of high-quality mesenchymal stem cells (MSCs). Since the discovery of dental pulp stem cells (DPSCs) in permanent third molars, stem cells from human exfoliated deciduous teeth and from supernumerary teeth (mesiodentes) have been identified as a population distinct from DPSCs. Dental pulp is divided into 2 parts based on the developing stage: the coronal pulp and the radicular pulp. Root formation begins after the crown part is completed. We performed a sequential study to examine the differences between the characteristics of coronal pulp cells (CPCs) and radicular pulp cells (RPCs) from permanent teeth, mesiodentes, and deciduous teeth. Interestingly, although we have not obtained any data on the difference between CPCs and RPCs in permanent teeth, there are some differences between the characteristics of CPCs and RPCs from mesiodentes and deciduous teeth. The MSC characteristics differed between the RPCs and CPCs, and the reprogramming efficiency for the generation of induced pluripotent stem cells was greater in RPCs than in CPCs from deciduous teeth. The proportion of CD105 + cells in CPCs versus that in RPCs varied in mesiodentes but not in permanent teeth. The results indicate that the proportion of CD105 + cells is an effective means of characterizing dental pulp cells in mesiodentes. Taken together, the stem cells in deciduous and supernumerary teeth share many characteristics, such as a high proliferation rate and an immunophenotype similar to that of DPSCs. Thus, mesiodentes accidentally encountered on radiographs by the general dental practitioner might be useful for stem cell therapy. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Physical protection of nuclear material

International Nuclear Information System (INIS)

1975-01-01

Full text: An Advisory Group met to consider the up-dating and extension of the Recommendations for the Physical Protection of Nuclear Material, produced in 1972. Twenty-seven experts from 11 countries and EURATOM were present. Growing concern has been expressed in many countries that nuclear material may one day be used for acts of sabotage or terrorism. Serious attention is therefore being given to the need for States to develop national systems for the physical protection of nuclear materials during use, storage and transport throughout the nuclear fuel cycle which should minimize risks of sabotage or theft. The revised Recommendations formulated by the Advisory Group include new definitions of the objectives of national systems of physical protection and proposals for minimizing possibilities of unauthorized removal and sabotage to nuclear facilities. The Recommendations also describe administrative or organizational steps to be taken for this purpose and the essential technical requirements of physical protection for various types and locations of nuclear material, e.g., the setting up of protected areas, the use of physical barriers and alarms, the need for security survey, and the need of advance arrangements between the States concerned in case of international transportation, among others. (author)

Effects of heat treatment on density, dimensional stability and color ...

African Journals Online (AJOL)

The purpose of this study was to evaluate the effect of heat treatment on some physical properties and color change of Pinus nigra wood which has high industrial use potential and large growing stocks in Turkey. Wood samples which comprised the material of the study were obtained from an industrial plant. Samples were ...

Performance of a Horizontal Double Cylinder Type of Fresh Coffee Cherries Pulping Machine

Directory of Open Access Journals (Sweden)

Sukrisno Widyotomo

2009-05-01

Full Text Available Pulping is one important step in wet coffee processing method. Usually, pulping process uses a machine which constructed using wood or metal materials. A horizontal single cylinder type coffee pulping machine is the most popular machine in coffee processor and market. One of the weakness of a horizontal single cylinder type coffee pulping machine is high of broken beans. Broken beans is one of major aspect in defect system that result in low quality. Indonesian Coffee and Cocoa Research Institute has designed and tested a horizontal double cylinder type coffee pulping machine. Material tested is Robusta cherry, mature, 60—65% (wet basis moisture content, which size compostition of coffee cherries was 50.8% more than 15 mm diameter, 32% more than 10 mm diameter, and 16.6% to get through 10 mm hole diameter; 690—695 kg/m3 bulk density, and clean from methal and foreign materials. The result showed that this machine has 420 kg/h optimal capacity in operational conditions, 1400 rpm rotor rotation speed for unsorted coffee cherries with composition 53.08% whole parchment coffee, 16.92% broken beans, and 30% beans in the wet skin. For small size coffee cherries, 603 kg/h optimal capacity in operational conditions, 1600 rpm rotor rotation speed with composition 51.30% whole parchment coffee, 12.59% broken beans, and 36.1% beans in the wet skin. Finally, for medium size coffee cherries, 564 kg/h optimal capacity in operational conditions, 1800 rpm rotor rotation speed with composition 48.64% whole parchment coffee, 18.5% broken beans, and 32.86% beans in the wet skin.Key words : coffee, pulp, pulper, cylinder, quality.

Morphological evaluation during in vitro chondrogenesis of dental pulp stromal cells

Directory of Open Access Journals (Sweden)

Choo-Ryung Chung

2012-02-01

Full Text Available Objectives The aim was to confirm the stem cell-like properties of the dental pulp stromal cells and to evaluate the morphologic changes during in vitro chondrogenesis. Materials and Methods Stromal cells were outgrown from the dental pulp tissue of the premolars. Surface markers were investigated and cell proliferation rate was compared to other mesenchymal stem cells. Multipotency of the pulp cells was confirmed by inducing osteogenesis, adipogenesis and chondrogenesis. The morphologic changes in the chondrogenic pellet during the 21 day of induction were evaluated under light microscope and transmission electron microscope. TUNEL assay was used to evaluate apoptosis within the chondrogenic pellets. Results Pulp cells were CD90, 105 positive and CD31, 34 negative. They showed similar proliferation rate to other stem cells. Pulp cells differentiated to osteogenic, adipogenic and chondrogenic tissues. During chondrogenesis, 3-dimensional pellet was created with multi-layers, hypertrophic chondrocyte-like cells and cartilage-like extracellular matrix. However, cell morphology became irregular and apoptotic cells were increased after 7 day of chondrogenic induction. Conclusions Pulp cells indicated mesenchymal stem cell-like characteristics. During the in vitro chondrogenesis, cellular activity was superior during the earlier phase (within 7 day of differentiation.

Study on the effect of shape-stabilized phase change materials on spacecraft thermal control in extreme thermal environment

International Nuclear Information System (INIS)

Wu, Wan-fan; Liu, Na; Cheng, Wen-long; Liu, Yi

2013-01-01

Highlights: ► A shape-stabilized PCM is used to protect the spacecraft attacked by high energy. ► Taking a satellite as example, it proves the solution given in the work is feasible. ► Low thermal conductivity makes the material above its thermal stability limit. ► It provides guidance on how to choose the shape-stabilized PCM for similar problems. - Abstract: In space, the emergencies such as short-term high heat flux is prone to cause spacecraft thermal control system faults, resulting in temperature anomalies of electronic equipment of the spacecraft and even failures in them. In order to protect the spacecraft attacked by the high energy, a new guard method is proposed. A shape-stabilized phase change material (PCM), which has high thermal conductivity and does not require being tightly packaged, is proposed to be used on the spacecraft. To prove the feasibility of using the material on spacecraft attacked by high energy, the thermal responses for spacecraft with shape-stabilized PCM are investigated in situations of normal and short-term high heat flux, in contrast to that with conventional thermal control system. The results indicate that the shape-stabilized PCM can effectively absorb the heat to prevent the thermal control system faults when the spacecraft’s outer heat flux changes dramatically and has no negative effect on spacecraft in normal heat flux. Additionally the effect of thermal conductivity of PCM on its application effectiveness is discussed

Gender and engineering aptitude: Is the color of science, technology, engineering, and math materials related to children's performance?

Science.gov (United States)

Mulvey, Kelly Lynn; Miller, Bridget; Rizzardi, Victoria

2017-08-01

To investigate gender stereotypes, demonstrated engineering aptitude, and attitudes, children (N=105) solved an engineering problem using either pastel-colored or primary-colored materials. Participants also evaluated the acceptability of denial of access to engineering materials based on gender and counter-stereotypic preferences (i.e., a boy who prefers pastel-colored materials). Whereas material color was not related to differences in female participants' performance, younger boys assigned to pastel materials demonstrated lower engineering aptitude than did other participants. In addition, results documented age- and gender-related differences; younger participants, and sometimes boys, exhibited less flexibility regarding gender stereotypes than did older and female participants. The findings suggest that attempts to enhance STEM (science, technology, engineering, and math) engagement or performance through the color of STEM materials may have unintended consequences. Copyright © 2017 Elsevier Inc. All rights reserved.

Color Rendering Index Thermal Stability Improvement of Glass-Based Phosphor-Converted White Light-Emitting Diodes for Solid-State Lighting

Directory of Open Access Journals (Sweden)

Chun-Chin Tsai

2014-01-01

Full Text Available High color rendering index performance has been required for phosphor-converted warm-white light-emitting diodes (PC-WWLEDs in lighting industry. The characteristics of low-temperature fabricated phosphor (yellow: Ce3+:YAG, green: Tb3+:YAG, and red: CaAlClSiN3:Eu2+ doped glass were presented for applications to high color rendering index warm-white-light-emitting diodes. Color coordinates (x, y = (0.36, 0.29, quantum yield (QY = 55.6%, color rending index (CRI = 85.3, and correlated color temperature (CCT = 3923 K were characterized. Glass-based PC-WWLEDs was found able to maintain good thermal stability for long-time high-temperature operation. QY decay, CRI remenance, and chromaticity shift were also analyzed for glass- and silicone-based high-power PC-WLEDs by thermal aging at 150°C and 250°C for industrial test standard’s aging time 1008 hours. Better than the silicone’s, thermal stability of glass-based PC-WLEDs has been improved. The resulted high color rendering index (CRI glass phosphor potentially can be used as a phosphor layer for high-performance and low-cost PC-WLEDs used in next-generation indoor solid-state lighting applications.

Electron treatment of wood pulp for the viscose process

Science.gov (United States)

Stepanik, T. M.; Ewing, D. E.; Whitehouse, R.

2000-03-01

Electron processing is currently being evaluated by several viscose producers for integration into their process. The viscose industry converts dissolving wood pulp into products such as staple fibre, filament, cord, film, packaging, and non-edible sausage casings. These materials are used in the clothing, drapery, hygiene, automobile, food, and packaging industries. Viscose producers are facing increasingly high production costs and stringent environmental regulations that have forced some plants to close. Electron treatment of wood pulp can significantly reduce the amounts of chemicals used for producing viscose and the production of hazardous pollutants. Acsion Industries has worked with companies worldwide to demonstrate the benefits of using electron treated pulp for producing viscose (rayon). This paper describes the viscose process, the benefits of using electron treatment in the viscose process, and Acsion's efforts in developing this technology.

Comparative study of the banana pulp browning process of 'Giant Dwarf' and FHIA-23 during fruit ripening based on image analysis and the polyphenol oxidase and peroxidase biochemical properties.

Science.gov (United States)

Escalante-Minakata, Pilar; Ibarra-Junquera, Vrani; Ornelas-Paz, José de Jesús; García-Ibáñez, Victoria; Virgen-Ortíz, José J; González-Potes, Apolinar; Pérez-Martínez, Jaime D; Orozco-Santos, Mario

2018-01-01

This work presents a novel method to associate the polyphenol oxidase (PPO) and the peroxidase (POD) activities with the ripening-mediated color changes in banana peel and pulp by computational image analysis. The method was used to follow up the de-greening of peel and browning of homogenized pulp from 'Giant Dwarf' (GD: Musa AAA, subgroup Cavendish) and FHIA-23 (tetraploid hybrid, AAAA) banana cultivars. In both cultivars, the color changes of peel during the ripening process clearly showed four stages, which were used to group the fruit into ripening stages. The PPO and POD were extracted from pulp of fruit at these ripening stages, precipitated, and partially purified by gel filtration chromatography. Moreover, the pulp browning was digitally monitored after homogenization for a span time of up to 120 min. The browning level was higher for GD than FHIA-23 tissues. This fact correlated with an 11.7-fold higher PPO activity in the GD cultivar, as compared with that of FHIA-23. POD activity was 8.1 times higher for GD as compared that that of FHIA-23.

Cellular Responses in Human Dental Pulp Stem Cells Treated with Three Endodontic Materials

Directory of Open Access Journals (Sweden)

Alejandro Victoria-Escandell

2017-01-01

Full Text Available Human dental pulp stem cells (HDPSCs are of special relevance in future regenerative dental therapies. Characterizing cytotoxicity and genotoxicity produced by endodontic materials is required to evaluate the potential for regeneration of injured tissues in future strategies combining regenerative and root canal therapies. This study explores the cytotoxicity and genotoxicity mediated by oxidative stress of three endodontic materials that are widely used on HDPSCs: a mineral trioxide aggregate (MTA-Angelus white, an epoxy resin sealant (AH-Plus cement, and an MTA-based cement sealer (MTA-Fillapex. Cell viability and cell death rate were assessed by flow cytometry. Oxidative stress was measured by OxyBlot. Levels of antioxidant enzymes were evaluated by Western blot. Genotoxicity was studied by quantifying the expression levels of DNA damage sensors such as ATM and RAD53 genes and DNA damage repair sensors such as RAD51 and PARP-1. Results indicate that AH-Plus increased apoptosis, oxidative stress, and genotoxicity markers in HDPSCs. MTA-Fillapex was the most cytotoxic oxidative stress inductor and genotoxic material for HDPSCs at longer times in preincubated cell culture medium, and MTA-Angelus was less cytotoxic and genotoxic than AH-Plus and MTA-Fillapex at all times assayed.

Immunohistochemical Expression of TGF-β1 and Osteonectin in engineered and Ca(OH2-repaired human pulp tissues

Directory of Open Access Journals (Sweden)

Luiz Alexandre CHISINI

Full Text Available Abstract The aim of the present study was to evaluate the expression of transforming growth factor-β1 (TGF-β1 and osteonectin (ON in pulp-like tissues developed by tissue engineering and to compare it with the expression of these proteins in pulps treated with Ca(OH2 therapy. Tooth slices were obtained from non-carious human third molars under sterile procedures. The residual periodontal and pulp soft tissues were removed. Empty pulp spaces of the tooth slice were filled with sodium chloride particles (250–425 µm. PLLA solubilized in 5% chloroform was applied over the salt particles. The tooth slice/scaffold (TS/S set was stored overnight and then rinsed thoroughly to wash out the salt. Scaffolds were previously sterilized with ethanol (100–70° and washed with phosphate-buffered saline (PBS. TS/S was treated with 10% EDTA and seeded with dental pulp stem cells (DPSC. Then, TS/S was implanted into the dorsum of immunodeficient mice for 28 days. Human third molars previously treated with Ca(OH2 for 90 days were also evaluated. Samples were prepared and submitted to histological and immunohistochemical (with anti-TGF-β1, 1:100 and anti-ON, 1:350 analyses. After 28 days, TS/S showed morphological characteristics similar to those observed in dental pulp treated with Ca(OH2. Ca(OH2-treated pulps showed the usual repaired pulp characteristics. In TS/S, newly formed tissues and pre-dentin was colored, which elucidated the expression of TGF-β1 and ON. Immunohistochemistry staining of Ca(OH2-treated pulps showed the same expression patterns. The extracellular matrix displayed a fibrillar pattern under both conditions. Regenerative events in the pulp seem to follow a similar pattern of TGF-β1 and ON expression as the repair processes.

Measurement of color in different construction materials. The restoration in sandstone buildings

Directory of Open Access Journals (Sweden)

García Pascua, N.

1999-03-01

Full Text Available The use of construction materials and their subsequent repair purposes include a search of knowledge and preservation of their original appearance. For this reason, the main aim of this study is to determine a color range which does not change with the possible actions on a building, both when restoration works which imply the use and repair of "ancient" materials are carried out, and when construction is carried out with new materials. It is necessary to obtain the quantification of this property in order to check its variation over the passage of time. Each construction material must be taken into account as an isolated problem, since the color is different in each case.

El empleo de materiales de construcción y la aplicación sobre ellos de productos de reparación requiere un detallado estudio sobre su forma de actuación y la importancia de la conservación del aspecto original de los mismos. Por este motivo, el objetivo principal de este estudio es el determinar un intervalo de color que se conserve a pesar de todas las posibles intervenciones que se acometan en el edificio, tanto cuando se realizan trabajos de restauración, que implican el uso y reparación de materiales "viejos", o bien cuando se llevan a cabo trabajos de construcción con materiales nuevos. Es necesario cuantificar dicha propiedad para poder controlar el paso del tiempo. Cada material de construcción debe ser considerado como un problema aislado, ya que el color es distinto en cada caso.

Use of additive material to stabilize the soil swelling

Science.gov (United States)

Parsaee, B.; Estabragh, A. R.; Bordbar, A. T.; Eskandari, G. H.

2009-04-01

Change volume increasing of soil, because of increase in its humidity content causes appearing of swelling phenomenon in the soil. This phenomenon has created a lot of damages in the building which is constructed on this kind of soils. Usage the additive materials which stabilize the swelling, has been the subject of many researches. In this research the Potential expansibility of the expansive soils, which were stabilized by additive materials such as Lime, cement and coal ash, was investigated. To get this purpose, by preparing soil samples mixed with upper additive material, changes of potential swelling of stabilized soils were compared. The results revealed that usage of these stabilizing materials caused the decrease in destructive effects due to swelling of soils to some extent. Keywords: swelling, soil stabilizing, additive material, coal ash

Potential of hot water extraction of birch wood to produce high-purity dissolving pulp after alkaline pulping.

Science.gov (United States)

Borrega, Marc; Tolonen, Lasse K; Bardot, Fanny; Testova, Lidia; Sixta, Herbert

2013-05-01

The potential of hot water extraction of birch wood to produce highly purified dissolving pulp in a subsequent soda-anthraquinone pulping process was evaluated. After intermediate extraction intensities, pulps with low xylan content (3-5%) and high cellulose yield were successfully produced. Increasing extraction intensity further decreased the xylan content in pulp. However, below a xylan content of 3%, the cellulose yield dramatically decreased. This is believed to be due to cleavage of glycosidic bonds in cellulose during severe hot water extractions, followed by peeling reactions during alkaline pulping. Addition of sodium borohydride as well as increased anthraquinone concentration in the pulping liquor increased the cellulose yield, but had no clear effects on pulp purity and viscosity. The low intrinsic viscosity of pulps produced after severe extraction intensities and soda-anthraquinone pulping corresponded to the viscosity at the leveling-off degree of polymerization, suggesting that nearly all amorphous cellulose had been degraded. Copyright © 2012 Elsevier Ltd. All rights reserved.

Bioceramic/Poly (glycolic-poly (lactic acid composite induces mineralized barrier after direct capping of rat tooth pulp tissue

Directory of Open Access Journals (Sweden)

Alfonso Gala-Garcia

2010-03-01

Full Text Available The aim of this study was to observe the histopathological pulp response following direct pulp capping of mechanically exposed teeth in rats with a composite of beta-tricalcium phosphate-hydroxyapatite bioceramic (BC and poly (glycolic-poly (lactic acid (PLGA material or a calcium hydroxide [Ca(OH2] material, compared to BC alone and a negative control of water. Pulp of the maxillary molars was exposed, followed by capping with the experimental material. The pulpal tissue response was assessed post-operatively at 1, 7, 14 and 30 d, followed by histological analysis. The Ca(OH2 group exhibited severe acute inflammatory cell infiltration at day 14. However after 30 d, a new hard tissue with macro porous obliteration of the pulp chamber and a characteristic necrotic area had appeared. BC and Ca(OH2 capping were associated with moderate inflammation and dentinal bridge similar. Meanwhile, in the BC/PLGA composite group, there was moderate inflammatory infiltrate and formation of a dense and complete dentinal bridge. In conclusion, the BC/PLGA composite material showed a large zone of tertiary dentin, and effectively reorganized the dentin-pulp complex.

Rapid determination of fluorine in the pulp process

International Nuclear Information System (INIS)

Ivanenko, V.V.; Kustov, V.N.; Levitskaya, O.N.

1994-01-01

The control of enrichment of mineral raw materials in order to increase the yield of enriched minerals is an important problem of modern industry. A possible solution is an automatic control system (ACS), which makes possible the monitoring and optimization of the enrichment. In terms of future applications, the nuclear-physical analysis, which is based on the use of a radionuclide source of neutrons, is a promising method. The advantages of this method (high rate, the possibility of performing the analysis directly in the flow, high accuracy, and high sensitivity) make themselves evident in the determination of short-lived isotopes, such as F, Ag, Si, Al, V, etc. Both an instrumental complex and a method for the rapid neutron activation determination (RNAD) of fluorine in the pulp flow of the enrichment process of raw materials were developed at the Institute of Chemistry, Far East Division, Russian Academy of Sciences. The analytical complex for RNAD comprises an activator; a densitometer; a pump; a pulp-feed system; a gamma-ray detector; a data acquisition apparatus; and a computer for processing the input/output data and controlling the analysis. The authors found that the RNAD of fluorine using radionuclide Pu-Be sources allows the determination in a 6-L pulp under recirculation conditions with an error of less than 1% in 3-5 minutes. The method allows the routine monitoring of the enrichment process of mineral raw materials

Color stability of ceramic brackets immersed in potentially staining solutions

Directory of Open Access Journals (Sweden)

Bruna Coser Guignone

2015-08-01

Full Text Available OBJECTIVE: To assess the color stability of five types of ceramic brackets after immersion in potentially staining solutions.METHODS: Ninety brackets were divided into 5 groups (n = 18 according to brackets commercial brands and the solutions in which they were immersed (coffee, red wine, coke and artificial saliva. The brackets assessed were Transcend (3M/Unitek, Monrovia, CA, USA, Radiance (American Orthodontics, Sheboygan, WI, USA, Mystique (GAC International Inc., Bohemia, NY, USA and Luxi II (Rocky Mountain Orthodontics, Denver, CO, USA. Chromatic changes were analyzed with the aid of a reflectance spectrophotometer and by visual inspection at five specific time intervals. Assessment periods were as received from the manufacturer (T0, 24 hours (T1, 72 hours (T2, as well as 7 days (T3 and 14 days (T4 of immersion in the aforementioned solutions. Results were submitted to statistical analysis with ANOVA and Bonferroni correction, as well as to a multivariate profile analysis for independent and paired samples with significance level set at 5%.RESULTS: The duration of the immersion period influenced color alteration of all tested brackets, even though these changes could not always be visually observed. Different behaviors were observed for each immersion solution; however, brackets immersed in one solution progressed similarly despite minor variations.CONCLUSIONS: Staining became more intense over time and all brackets underwent color alterations when immersed in the aforementioned solutions.

FY 1999 report on the results of the development of recycling technology of waste architectural materials, glass, etc. Development of the simple glass coloring/decoloring technology; 1999 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kan'igata glass chakudasshoku gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of increasing the ratio of recycling of waste architectural materials, glass, etc., the development was proceeded with of easy coloring of colorless glass by light irradiation and decoloring of it by heat treatment. The important point for technical development is to develop glass materials which are colored by light and decolored by heat at a level of technique with practicality and to develop coloring/decoloring device. Studies were made in the following three fields: 1) optimization of coloring/decoloring conditions for coloring/decoloring occurring from defects (color centers) under light irradiation; 2) optimization of coloring/decoloring conditions occurring from colorless ions and particulate formation under light irradiation; 3) development of a visible drawing device. In 1), bottle, sheet glass, and soda-lime silicate glass are colored brown by X-ray/UV radiation, but the coloring is bad in stability. However, it was found that the addition of silver oxide improved stability. In 2), it was recognized that when the glass containing a trace of Mn was melted in the reducing atmosphere, it became colorless, and when radiated by X-ray and heat-treated at approximately 200 degrees C, it was colored bluish violet which was vivid and stable. (NEDO)

Comparison of Calcium Hydroxide and Bioactive Glass after Direct Pulp Capping in Primary Teeth

Directory of Open Access Journals (Sweden)

R. Haghgoo

2007-12-01

Full Text Available Objective: Bioactive glass is often used as a filler material for repair of dental bone defects.In different studies osteogenic potential of this material was proved, but its dentinogenesisproperty is in doubt. The purpose of this study was to evaluate the histological pulp responses of Calcium hydroxide and Bioactive glass placed directly on exposed pulp tissues.Materials and Methods: Twenty teeth to be extracted due to orthodontic reasons were selected. These teeth were divided into two groups and treated with direct pulp capping.Calcium hydroxide was used for 10 teeth and Bioactive glass for 10 teeth. After 60 daysthe teeth were extracted and prepared for histological evaluation. Finally the data was analyzed with exact Fisher test.Results: All teeth treated with Calcium hydroxide showed inflammation. Internal resorption was seen in six teeth, abscess in five teeth and dentinal bridge in two teeth. Inflammationwas seen in three Bioactive glass samples and dentinal bridge in seven teeth, but internal resorption and abscess were not seen.Conclusion: Bioactive glass appears to be superior to Calcium hydroxide as a pulp capping agent in primary teeth.

Characterization and sensory preference of fermented dairy beverages prepared with different concentrations of whey and araticum pulp

Directory of Open Access Journals (Sweden)

Alexsandra Valéria Sousa Costa de Lima

2016-12-01

Full Text Available The objective of this study was to develop a fermented dairy beverage flavored with araticum pulp, assess its physicochemical characteristics, microbiological quality, and sensory preference by the consumer. Araticum pulp was prepared using two different methods: with or without bleaching (50 ºC/5 minutes. Formulations of fermented dairy beverages consisting of whey (50%, standardized pasteurized milk (50%, and seven different concentrations of bleached araticum pulp (5.0, 7.5, 10.0, 12.5, 15.0, 17.5, and 20.0% w/v were prepared. In addition, seven formulations of fermented dairy beverage, without adding araticum pulp, and consisting of varying proportions of whey (40, 50, 60, 70, 80, 90, and 100% were developed. In all formulations, thickeners/stabilizers were added. All araticum pulp samples (with and without bleach and fermented dairy beverages (with and without araticum pulp were analyzed for the relevant physicochemical properties: pH, titratable acidity, acidity of pulp, acidity of fermented beverage, moisture, ash, fat, protein, crude fiber, ascorbic acid, carbohydrates, total solids, and caloric values. Microbiological counts of coliforms at 35 °C and 45 °C in the pulp and beverage, and molds and yeasts and Salmonella sp. in the pulp were obtained. Additionally, sensory analysis regarding preferences of the different fermented dairy beverage formulations was also performed. The araticum pulp samples without bleach, showed higher values of pH, moisture, protein, total fiber, and ascorbic acid, as compared to bleached pulp samples, while bleached araticum pulp showed higher values for other physicochemical parameters. Microbiological results showed that all pulps and fruit-dairy beverages were suitable for consumption. It was found that there was no significant consumer preference between different fermented beverage formulations, according to the different percentages of pulp. However, the formulations consisting of 40, 50, 60, and 70

Color Stability Assessment of Two Different Composite Resins with Variable Immersion Time Using Various Beverages: An In vitro Study.

Science.gov (United States)

Kumar, M Senthil; Ajay, R; Miskeen Sahib, S A; Chittrarasu, M; Navarasu, M; Ragavendran, N; Burhanuddin Mohammed, Omar Farooq

2017-11-01

The aim of the study was to evaluate the difference in the color of microhybrid (MH) and nanofilled (NF) composite resins after 24 and 48 h in beverages such as red wine (RW), Coca-Cola, and distilled water. The specific objective of this study was to investigate the cumulative effect of the colorant solutions on the dental composites. MH and NF composite resins (A2 shade) were used in this current study. Sixty disk-shaped material specimens (10 mm in diameter × 2 mm in thickness) were prepared using a fiber mold (ring), with the desired dimensions. The specimen surfaces were polished using super-snap polishing system. Sixty specimens were divided into two groups of 30 each (Group I: MH resin composite; Group II: NF resin composite). Both the groups divided into six subgroups (Subgroup I: RW for 24 h [RW-24]; Subgroup II: RW for 48 h; Subgroup III: Coca-Cola for 24 h [CC-24]; Subgroup IV: Coca-Cola for 48 h [CC-48]; Subgroup V: Distilled water for 24 h [DW-24]; Subgroup VI: Distilled water for 48 h [DW-48]). All the samples were immersed in respective drinks for a period of 24 h, and color differences were measured using ultraviolet spectrophotometer. Once again, all the samples were immersed for another 24 h in the same drinks. After 48 h, the color change of the samples was measured. Measurements were made according to the CIE L × a × b × color space relative to the CIE standard illuminant D65. The color changes of the specimens were evaluated using the following formula: Statistical analysis was performed. The data were analyzed using the one-way ANOVA and t -test at a significance level of 0.05. Color stability of MH composite resin was found to be inferior than the NF resin composite irrespective of immersion medium and time. In RW, the color change observed was maximum for both composite resins followed by Coca-Cola. Immersing the resin composites in distilled water for 24 and 48 h had negligible color change. A 48-h immersion of both composite resins in

Extracellular matrix of dental pulp stem cells: Applications in pulp tissue engineering using somatic MSCs

Directory of Open Access Journals (Sweden)

Sriram eRavindran

2014-01-01

Full Text Available Dental Caries affects approximately 90% of the world’s population. At present, the clinical treatment for dental caries is root canal therapy. This treatment results in loss of tooth sensitivity and vitality. Tissue engineering can potentially solve this problem by enabling regeneration of a functional pulp tissue. Dental pulp stem cells (DPSCs have been shown to be an excellent source for pulp regeneration. However, limited availability of these cells hinders its potential for clinical translation. We have investigated the possibility of using somatic mesenchymal stem cells from other sources for dental pulp tissue regeneration using a biomimetic dental pulp extracellular matrix (ECM incorporated scaffold. Human periodontal ligament stem cells (PDLSCs and human bone marrow stromal cells (HMSCs were investigated for their ability to differentiate towards an odontogenic lineage. In vitro real-time PCR results coupled with histological and immunohistochemical examination of the explanted tissues confirmed the ability of PDLSCs and HMSCs to form a vascularized pulp-like tissue. These findings indicate that the dental pulp stem derived ECM scaffold stimulated odontogenic differentiation of PDLSCs and HMSCs without the need for exogenous addition of growth and differentiation factors. This study represents a translational perspective toward possible therapeutic application of using a combination of somatic stem cells and extracellular matrix for pulp regeneration.

Arundo donax L. reed: new perspectives for pulping and bleaching. Part 4. Peroxide bleaching of organosolv pulps.

Science.gov (United States)

Shatalov, A A; Pereira, H

2005-05-01

A comparative study on TCF (totally chlorine-free) bleachability of organosolv pulps from the annual fibre crop Arundo donax L. (giant reed) was carried out using a simple three-stage peroxide bleaching sequence without oxygen pre-bleaching. ASAM (alkali-sulfite-anthraquinone-methanol), Organocell (alkali-anthraquinone-methanol) and ethanol-soda organosolv pulps were bleached and compared with kraft pulp, as a reference. The final brightness of 76-78% ISO was attained for all tested pulps. The chemical charge required to reach this level of brightness varied for different pulps (despite the equal initial content of the residual lignin) and directly related to starting brightness values. No direct correlation between brightness improvement and lignin removal during bleaching was found, indicating the influence of the specific pulp properties introduced by pulping process on bleaching chemistry. The general higher bleaching response of organosolv pulps from A. donax was noted in comparison with kraft.

Oxidative stability of pork emulsion containing tomato products and pink guava pulp during refrigerated aerobic storage

OpenAIRE

Joseph, Serlene; Chatli, Manish K.; Biswas, Ashim K.; Sahoo, Jhari

2012-01-01

Lipid oxidation-induced quality problems can be minimized with the use of natural antioxidants. Antioxidant potential of tomato puree (10 %; T-1), tomato pulp (12.5 %; T-2), lyophilized tomato peel (6 %; T-3), and pink guava pulp (10 %; T-4) was evaluated in raw pork emulsion during refrigerated storage for 9 days under aerobic packaging. The lycopene and β-carotene content varied in pork emulsion as T-3 > T-1 > T-2 > T-4 and decreased (P 

Membrane-stabilizing copolymers confer marked protection to dystrophic skeletal muscle in vivo

Directory of Open Access Journals (Sweden)

Evelyne M Houang

Full Text Available Duchenne muscular dystrophy (DMD is a fatal disease of striated muscle deterioration. A unique therapeutic approach for DMD is the use of synthetic membrane stabilizers to protect the fragile dystrophic sarcolemma against contraction-induced mechanical stress. Block copolymer-based membrane stabilizer poloxamer 188 (P188 has been shown to protect the dystrophic myocardium. In comparison, the ability of synthetic membrane stabilizers to protect fragile DMD skeletal muscles has been less clear. Because cardiac and skeletal muscles have distinct structural and functional features, including differences in the mechanism of activation, variance in sarcolemma phospholipid composition, and differences in the magnitude and types of forces generated, we speculated that optimized membrane stabilization could be inherently different. Our objective here is to use principles of pharmacodynamics to evaluate membrane stabilization therapy for DMD skeletal muscles. Results show a dramatic differential effect of membrane stabilization by optimization of pharmacodynamic-guided route of poloxamer delivery. Data show that subcutaneous P188 delivery, but not intravascular or intraperitoneal routes, conferred significant protection to dystrophic limb skeletal muscles undergoing mechanical stress in vivo. In addition, structure-function examination of synthetic membrane stabilizers further underscores the importance of copolymer composition, molecular weight, and dosage in optimization of poloxamer pharmacodynamics in vivo.

Software hazard analysis for nuclear digital protection system by Colored Petri Net

International Nuclear Information System (INIS)

Bai, Tao; Chen, Wei-Hua; Liu, Zhen; Gao, Feng

2017-01-01

Highlights: •A dynamic hazard analysis method is proposed for the safety-critical software. •The mechanism relies on Colored Petri Net. •Complex interactions between software and hardware are captured properly. •Common failure mode in software are identified effectively. -- Abstract: The software safety of a nuclear digital protection system is critical for the safety of nuclear power plants as any software defect may result in severe damage. In order to ensure the safety and reliability of safety-critical digital system products and their applications, software hazard analysis is required to be performed during the lifecycle of software development. The dynamic software hazard modeling and analysis method based on Colored Petri Net is proposed and applied to the safety-critical control software of the nuclear digital protection system in this paper. The analysis results show that the proposed method can explain the complex interactions between software and hardware and identify the potential common cause failure in software properly and effectively. Moreover, the method can find the dominant software induced hazard to safety control actions, which aids in increasing software quality.

The Physical Protection of Nuclear Material

International Nuclear Information System (INIS)

1993-09-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers [es

The Physical Protection of Nuclear Material

International Nuclear Information System (INIS)

1993-09-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers [fr

The Physical Protection of Nuclear Material

International Nuclear Information System (INIS)

1993-01-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers

The Physical Protection of Nuclear Material

International Nuclear Information System (INIS)

1993-09-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers

REPLACEMENT OF SOFTWOOD KRAFT PULP WITH ECF-BLEACHED BAMBOO KRAFT PULP IN FINE PAPER

Directory of Open Access Journals (Sweden)

Guanglei Zhao

2010-06-01

Full Text Available Non-wood fibers such as bamboo and wheat straw have been playing important roles in the pulp and paper industry in China. In this study an ECF-bleached bamboo kraft pulp was compared with a bleached softwood kraft pulp (NBSK as the reinforcement pulp in fine paper production. Areas that were examined include the refining of pure fibers, influence of bamboo on dewatering, retention, and sizing. The influence of bamboo kraft pulp as a part of a furnish replacing NBSK was compared as well. Results show that fiber shortening was more prominent with bamboo when refined. This resulted in a higher amount of fines, and addition wet-end chemicals may be required to compensate. Handsheets with bamboo as a reinforcement fiber showed similar mechanical and optical properties to handsheets containing NBSK.

Application of Alkaline Ionic Liquids in the Pretreatment Process of Eucalyptus Kraft Pulping

Directory of Open Access Journals (Sweden)

Yi Hou

2016-09-01

Full Text Available In order to explore the potential application of green solvent ionic liquids (ILs in the kraft pulping process, eucalyptus wood was pretreated by [Mmim]DMP before normal pulping. The results showed that materials pretreated shortly by the ionic liquid had a higher yield and viscosity coupled with a lower potassium permanganate value and residual lignin content in the pulp, as a result of the cooking process. It was also inferred that alkaline [Mmim]DMP pretreatment could dissolve lignin effectively from fiber to result in a stronger binding force and more entangled properties. Paper tensile and burst strength were improved by about 40% and 60%, respectively. These results provide a new way for eucalyptus to be utilized in the kraft pulping process.

Study on Effectiveness of Processed and Unprocessed Black Liquor pulps in improving the properties of PPC mortar, Concrete and SCC

Science.gov (United States)

Ananthkumar, M.; Sathyan, Dhanya; Prabha, B.

2018-02-01

The cost of construction materials is increasing day by day because of high demand, scarcity of raw materials and high price of energy. From the view point of energy saving and over consumption of resources, the use of alternative constituents in construction materials is now a global concern. From this, the extensive research and development works towards exploring new ingredients are required for producing sustainable and environment friendly construction materials. Bagasse pulp liquor is one such material that can be used as a chemical admixture which is obtained as a by-product of paper manufacturing process. Around 5 million tons of bagasse pulp is obtained throughout the world each year. since the material is a waste product from paper industry, this can be changed as a admixture by its effective use in concrete. In the present investigation black pulp liquor is added to fresh concrete in different dosages, the concrete is then tested for workability, compressive strength, flexural, split tensile strength and setting time. From results it is shown that 1% replacement of water with black pulp liquor increases the fresh properties of the concrete, 2% replacement of water with black pulp liquor increases the mechanical properties of the concrete and acts as a set retarder.

Use of high-boiling point organic solvents for pulping oil palm empty fruit bunches.

Science.gov (United States)

Rodríguez, Alejandro; Serrano, Luis; Moral, Ana; Pérez, Antonio; Jiménez, Luis

2008-04-01

Oil palm empty fruit bunches were used as an alternative raw material to obtain cellulosic pulp. Pulping was done by using high-boiling point organic solvents of decreased polluting power relative to classical (Kraft, sulphite) solvents but affording operation at similar pressure levels. The holocellulose, alpha-cellulose and lignin contents of oil palm empty fruit bunches (viz. 66.97%, 47.91% and 24.45%, respectively) are similar to those of some woody raw materials such as pine and eucalyptus, and various non-wood materials including olive tree prunings, wheat straw and sunflower stalks. Pulping tests were conducted by using ethyleneglycol, diethyleneglycol, ethanolamine and diethanolamine under two different sets of operating conditions, namely: (a) a 70% solvent concentration, 170 degrees C and 90 min; and (b) 80% solvent, 180 degrees C and 150 min. The solid/liquid ratio was six in both cases. The amine solvents were found to provide pulp with better properties than did the glycol solvents. Ethanolamine pulp exhibited the best viscosity and drainage index (viz. 636 mL/g and 17 degrees SR, respectively), and paper made from it the best breaking length (1709 m), stretch (1.95%), burst index (0.98 kN/g) and tear index (0.33 mNm(2)/g). Operating costs can be reduced by using milder conditions, which provide similar results. In any case, the amines are to be preferred to the glycols as solvents for this purpose.

POST-ACIDIFICATION AND EVALUATION OF ANTHOCYANINS STABILITY AND ANTIOXIDAN ACTIVITY IN AÇAI FERMENTED MILK AND YOGURTS (Euterpe oleracea Mart.

Directory of Open Access Journals (Sweden)

DANIELA CAVALCANTE DOS SANTOS CAMPOS

2017-12-01

Full Text Available ABSTRACT This study evaluated the post-acidification, stability of anthocyanins and antioxidant activity in açai yogurts and fermented milks for 28 days of cold storage. For the determination of post-acidification and stability of the functional properties of açai yogurt (IA and fermented milks (LFA, products stored at 4°C were evaluated on day 0 and every 7 days for pH, titratable acidity in lactic acid, instrumental color, anthocyanins and antioxidant activity by the DPPH free radical method. Acidification of both food matrixes was more evident between days 0 and 7 of evaluation. IA presented reduction in parameter L *, while chromaticity a * and b * of IA and LFA increased as the Açai pulp content increased; however, considering the evaluation period, it was found increase in L * and b * relating to anthocyanin degradation. Anthocyanins, as well as the antioxidant activity of IA and LFA, showed an increase in their values as the pulp content increased, but their concentrations reduced at the end of the storage period. IA and LFA can be considered excellent sources of antioxidants, being alternative to individuals not used to the consumption of fruits and vegetables.

Material stabilization characterization management plan

International Nuclear Information System (INIS)

GIBSON, M.W.

1999-01-01

This document presents overall direction for characterization needs during stabilization of SNM at the Plutonium Finishing Plant (PFP). Technical issues for needed data and equipment are identified. Information on material categories and links to vulnerabilities are given. Comparison data on the material categories is discussed to assist in assessing the relative risks and desired processing priority

Copyright Protection of Color Imaging Using Robust-Encoded Watermarking

Directory of Open Access Journals (Sweden)

M. Cedillo-Hernandez

2015-04-01

Full Text Available In this paper we present a robust-encoded watermarking method applied to color images for copyright protection, which presents robustness against several geometric and signal processing distortions. Trade-off between payload, robustness and imperceptibility is a very important aspect which has to be considered when a watermark algorithm is designed. In our proposed scheme, previously to be embedded into the image, the watermark signal is encoded using a convolutional encoder, which can perform forward error correction achieving better robustness performance. Then, the embedding process is carried out through the discrete cosine transform domain (DCT of an image using the image normalization technique to accomplish robustness against geometric and signal processing distortions. The embedded watermark coded bits are extracted and decoded using the Viterbi algorithm. In order to determine the presence or absence of the watermark into the image we compute the bit error rate (BER between the recovered and the original watermark data sequence. The quality of the watermarked image is measured using the well-known indices: Peak Signal to Noise Ratio (PSNR, Visual Information Fidelity (VIF and Structural Similarity Index (SSIM. The color difference between the watermarked and original images is obtained by using the Normalized Color Difference (NCD measure. The experimental results show that the proposed method provides good performance in terms of imperceptibility and robustness. The comparison among the proposed and previously reported methods based on different techniques is also provided.

Enzymes improve ECF bleaching of pulp

Directory of Open Access Journals (Sweden)

Lachenal, D.

2006-07-01

Full Text Available The delignification efficiency of different laccase enzymes was examined on the eucalyptus Kraft pulp. The laccase enzyme from Trametes versicolor showing the highest delignification efficiency was selected and used in the elemental chlorine-free bleaching sequence for improving the pulp bleachability. An appreciable reduction in chlorine dioxide consumption was also obtained. Further reduction in chlorine dioxide consumption was obtained when the same laccase treated pulp was subjected to an acid treatment after the extraction stage followed by the DEPD sequence. Elemental-chlorine free bleaching was also performed using the xylanase-laccase treated pulp. Xylanase treatment was incorporated to the laccase mediator system in the elemental-chlorine free bleaching both sequentially and simultaneously. The bleaching sequence DEPD followed and in both the cases, the reduction in chlorine dioxide consumption was greater in comparison to the control. The chlorine dioxide consumption was reduced further when xylanase-laccase treated pulp was given an additional acid treatment. The final pulp properties of the treated pulps were comparable to the control pulp.

Dietary citrus pulp improves protein stability in lamb meat stored under aerobic conditions

DEFF Research Database (Denmark)

Gravador, Rufielyn Sungcaya; Jongberg, Sisse; Andersen, Mogens Larsen

2014-01-01

The antioxidant effects of dried citrus pulp on proteins in lamb meat, when used as a replacement of concentrate in the feed, was studied using meat from 26 male Comisana lambs. The lambs of age 90. days had been grouped randomly to receive one of the three dietary treatments: (1) commercial...

Human dental pulp stem cells with highly angiogenic and neurogenic potential for possible use in pulp regeneration.

Science.gov (United States)

Nakashima, Misako; Iohara, Koichiro; Sugiyama, Masahiko

2009-01-01

Dental caries is a common public health problem, causing early loss of dental pulp and resultant tooth loss. Dental pulp has important functions to sustain teeth providing nutrient and oxygen supply, innervation, reactionary/reparative dentin formation and immune response. Regeneration of pulp is an unmet need in endodontic therapy, and angiogenesis/vasculogenesis and neurogenesis are critical for pulp regeneration. Permanent and deciduous pulp tissue is easily available from teeth after extraction without ethical issues and has potential for clinical use. In this review, we introduce some stem cell subfractions, CD31(-)/CD146(-) SP cells and CD105(+) cells with high angiogenic and neurogenic potential, derived from human adult dental pulp tissue. Potential utility of these cells is addressed as a source of cells for treatment of cerebral and limb ischemia and pulp inflammation complete with angiogenesis and vasculogenesis.

Method of manufacturing neutron protection materials

Energy Technology Data Exchange (ETDEWEB)

Kakibana, Hidetake; Okamoto, Masazane; Fujii, Yasuhiko; Koguchi, Noboru; Takesute, Morito; Miyamatsu, Tokuhisa

1985-06-22