Glovebox design requirements for molten salt oxidation processing of transuranic waste

International Nuclear Information System (INIS)

Ramsey, K.B.; Acosta, S.V.; Wernly, K.D.

1998-01-01

This paper presents an overview of potential technologies for stabilization of 238 Pu-contaminated combustible waste. Molten salt oxidation (MSO) provides a method for removing greater than 99.999% of the organic matrix from combustible waste. Implementation of MSO processing at the Los Alamos National Laboratory (LANL) Plutonium Facility will eliminate the combustible matrix from 238 Pu-contaminated waste and consequently reduce the cost of TRU waste disposal operations at LANL. The glovebox design requirements for unit operations including size reduction and MSO processing will be presented

Development of crystalline ceramic for immobilization of TRU wastes in V.G. Khlopin Radium Institute

International Nuclear Information System (INIS)

Burakov, B.E.; Anderson, E.B.

1999-01-01

This paper discusses the Radium Institute's experience in the synthesis of crystalline ceramics based on two groups of actinide host-phases: 1) Zircon/zirconia-(Zn, Ac)SiO 4 /(Zr, Ac)O 2 , where Ac=Pu, Np, Am, Cm; 2) Garnet/perovskite-(Y, Gd, Ac) 3 (Al, Ga, Ac,..) 5 O 12 /(Y, Gd, Ac)(Al, Ga)O 3 . The zircon/zirconia ceramic was suggested as an universal waste form for the immobilization of TRU as well as weapon-grade Pu. Because the position of the Russian Ministry of Atomic Energy (Minatom) does not consider weapons Pu as a waste', the Radium Institute proposed the use of the same ceramic (mainly monophase zirconia ) as a Pu-fuel. The garnet/perovskite ceramic was suggested for the immobilization of military TRU wastes of complex chemical composition. The advantage of this ceramic is that Garnet and Perovskite host-phases can incorporate in their lattices not only actinides, but also other elements including neutron absorbers in a broad range of concentration and in different valence state. Sample of zircon/zirconia ceramic were prepared by hot uniaxial pressing (at temperature T=1300, 1400, 1500degC and pressure P=25 MPa) and sintering (at T=1450, 1490, 1500, 1600degC) methods using different types of initial precursor. Samples of garnet/perovskite ceramic were synthesized by melting method at T=2000degC. Ce, U, Gd were used as TRU stimulants for both types of ceramic. One sample of zircon/zirconia ceramic was doped with 10 wt.% of Pu 239 . Physico-chemical features of these ceramics are described. In conclusion we propose that the pressureless technology based on sintering or melting methods be used for the synthesis of ceramics for the immobilization of all types of TRU wastes. (author)

MANAGEING THE RETRIEVAL RISK OF BURIED TRANSURANIC (TRU) WASTE WITH UNIQUE CHARACTERISTICS

International Nuclear Information System (INIS)

WOJTASEK, R.D.; GREENWELL, R.D.

2005-01-01

United States-Department of Energy (DOE) sites that store transuranic (TRU) waste are almost certain to encounter waste packages with characteristics that are so unique as to warrant special precautions for retrieval. At the Hanford Site, a subgroup of stored TRU waste (12 drums) had special considerations due to the radioactive source content of plutonium oxide (PuO 2 ), and the potential for high heat generation, pressurization, criticality, and high radiation. These characteristics bear on the approach to safely retrieve, overpack, vent, store, and transport the waste package. Because of the potential risk to personnel, contingency planning for unexpected conditions played an effective roll in work planning and in preparing workers for the field inspection activity. As a result, the integrity inspections successfully confirmed waste package configuration and waste confinement without experiencing any perturbations due to unanticipated packaging conditions. This paper discusses the engineering and field approach to managing the risk of retrieving TRU waste with unique characteristics

Leaching properties of solidified TRU waste forms

International Nuclear Information System (INIS)

Colombo, P.; Neilson, R.M. Jr.

1979-01-01

Safety analysis of waste forms requires an estimate of the ability of these forms to retain activity in the disposal environment. This program of leaching tests will determine the leaching properties of TRU contaminated incinerator ash waste forms using hydraulic cement, urea--formaldehyde, bitumen, and vinyl ester--styrene as solidification agents. Three types of leaching tests will be conducted, including both static and flow rate. Five generic groundwaters will be used. Equipment and procedures are described. Experiments have been conducted to determine plate out of 239 Pu, counter efficiency, and stability of counting samples

Glovebox design requirements for molten salt oxidation processing of transuranic waste

Energy Technology Data Exchange (ETDEWEB)

Ramsey, K.B.; Acosta, S.V. [Los Alamos National Lab., NM (United States); Wernly, K.D. [Molten Salt Oxidation Corp., Bensalem, PA (United States)

1998-12-31

This paper presents an overview of potential technologies for stabilization of {sup 238}Pu-contaminated combustible waste. Molten salt oxidation (MSO) provides a method for removing greater than 99.999% of the organic matrix from combustible waste. Implementation of MSO processing at the Los Alamos National Laboratory (LANL) Plutonium Facility will eliminate the combustible matrix from {sup 238}Pu-contaminated waste and consequently reduce the cost of TRU waste disposal operations at LANL. The glovebox design requirements for unit operations including size reduction and MSO processing will be presented.

Nondestructive assay of TRU waste using gamma-ray active and passive computed tomography

International Nuclear Information System (INIS)

Roberson, G.P.; Decman, D.; Martz, H.; Keto, E.R.; Johansson, E.M.

1995-01-01

The authors have developed an active and passive computed tomography (A and PCT) scanner for assaying radioactive waste drums. Here they describe the hardware components of their system and the software used for data acquisition, gamma-ray spectroscopy analysis, and image reconstruction. They have measured the performance of the system using ''mock'' waste drums and calibrated radioactive sources. They also describe the results of measurements using this system to assay a real TRU waste drum with relatively low Pu content. The results are compared with X-ray NDE studies of the same TRU waste drum as well as assay results from segmented gamma scanner (SGS) measurements

Plutonium-238 alpha-decay damage study of the ceramic waste form

International Nuclear Information System (INIS)

Frank, S. M.; Barber, T. L.; Cummings, D.G.; DiSanto, T.; Esh, D.W.; Giglio, J. J.; Goff, K. M.; Johnson, S.G.; Kennedy, J.R.; Jue, J-F; Noy, M.; O'Holleran, T.P.; Sinkler, W.

2006-01-01

An accelerated alpha-decay damage study of a glass-bonded sodalite ceramic waste form has recently been completed. The purpose of this study was to investigate the physical and chemical durability of the waste form after significant exposure to alpha decay. This accelerated alpha-decay study was performed by doping the ceramic waste form with 238 Pu which has a much greater specific activity than 239 Pu that is normally present in the waste form. The alpha-decay dose at the end of the four year study was approximately 1 x 10 18 alpha-decays/gram of material. An equivalent time period for a similar dose of 239 Pu would require approximately 1100 years. After four years of exposure to 238 Pu alpha decay, the investigation observed little change to the physical or chemical durability of the ceramic waste form (CWF). Specifically, the 238 Pu-loaded CWF maintained it's physical integrity, namely that the density remained constant and no cracking or phase de-bonding was observed. The materials chemical durability and phase stability also did not change significantly over the duration of the study. The only significant measured change was an increase of the unit-cell lattice parameters of the plutonium oxide and sodalite phases of the material and an increase in the release of salt components and plutonium of the waste form during leaching tests, but, as mentioned, these did not lead to any overall loss of waste form durability. The principal findings from this study are: (1) 238 Pu-loaded CWF is similar in microstructure and phase composition to referenced waste form. (2) Pu was observed primarily as oxide comprised of aggregates of nano crystals with aggregates ranging in size from submicron to twenty microns in diameter. (3) Pu phases were primarily found in the intergranular glassy regions. (4) PuO phase shows expected unit cell volume expansion due to alpha decay damage of approximately 0.7%, and the sodalite phase unit cell volume has expanded slightly by 0.3% again

Aspects of 238Pu production in the experimental fast reactor JOYO

International Nuclear Information System (INIS)

Osaka, Masahiko; Koyama, Shin-ichi; Tanaka, Kenya; Itoh, Masahiko; Saito, Masaki

2005-01-01

Experimental determination of 238 Pu in 237 Np samples irradiated in the experimental fast reactor JOYO was done as part of the demonstration of 238 Pu production from 237 Np in fast reactors within the framework of the protected Pu production project, which aims at reinforcement of proliferation resistance of Pu by increasing the 238 Pu isotopic ratio. 238 Pu production amount in the irradiated 237 Np samples was determined by a radioanalytical technique. Aspects of 238 Pu production were examined on the basis of the present radioanalysis. The 238 Pu production amount depends on the neutron spectrum which can range from that of a typical fast reactor to a nearly epi-thermal spectrum. It is concluded that the fast reactor has not only high potential for use in protected Pu production, but also as an incinerator for excess Pu

Performance assessment requirements for the identification and tracking of transuranic waste intended for disposal at the Waste Isolation Pilot Plant

Energy Technology Data Exchange (ETDEWEB)

Snider, C.A. [Department of Energy, Carlsbad, NM (United States); Weston, W.W. [Westinghouse Electric Corp., Carlsbad, NM (United States)

1997-11-01

To demonstrate compliance with environmental radiation protection standards for management and disposal of transuranic (TRU) radioactive wastes, a performance assessment (PA) of the Waste Isolation Pilot Plant (WIPP) was made of waste-waste and waste-repository interactions and impacts on disposal system performance. An estimate of waste components and accumulated quantities was derived from a roll-up of the generator/storage sites` TRU waste inventories. Waste components of significance, and some of negligible effect, were fixed input parameters in the model. The results identified several waste components that require identification and tracking of quantities to ensure that repository limits are not exceeded. The rationale used to establish waste component limits based on input estimates is discussed. The distinction between repository limits and waste container limits is explained. Controls used to ensure that no limits are exceeded are identified. For waste components with no explicit repository based limits, other applicable limits are contained in the WIPP Waste Acceptance Criteria (WAC). The 10 radionuclides targeted for identification and tracking on either a waste container or a waste stream basis include Am-241, Pu-238, Pu-239, Pu-240, Pu-242, U-233, U-234, U-238, Sr-90, and Cs-137. The accumulative activities of these radionuclides are to be inventoried at the time of emplacement in the WIPP. Changes in inventory curie content as a function of radionuclide decay and ingrowth over time will be calculated and tracked. Due to the large margin of compliance demonstrated by PA with the 10,000 year release limits specified, the quality assurance objective for radioassay of the 10 radionuclides need to be no more restrictive than those already identified for addressing the requirements imposed by transportation and WIPP disposal operations in Section 9 of the TRU Waste Characterization Quality Assurance Program Plan. 6 refs.

Evaluation of a TRU fundamental criterion and reference TRU waste units

International Nuclear Information System (INIS)

Klett, R.

1993-01-01

The comparison of two options for regulating transuranic (TRU) waste disposal is explained in this paper. The two options are (1) fundamental and derived standards developed specifically for the TRU waste and (2) a family of procedures that use a reference to the TRU waste unit with procedures that use a reference to the TRU waste unit with commercial high-level waste (HLW) criteria. Background information pertaining to both options is covered. A section on criteria specifically for TRUE waste suggests a methodology for developing or adapting fundamental and derived criteria that are consistent with all other aspects of the standards. The section on references TRU waste units covers all the parameter variations that have been suggested for this option. The technical bases of each approach is reviewed, implementation is discussed and their relative attributes and deficiencies are evaluated

238Pu fuel form processes. Final report, January-September 1983

International Nuclear Information System (INIS)

Mosley, W.C.; Taylor, D.H.

1983-01-01

Progress is reported on the following: analytical studies of weld-quench cracking in DOP-26 iridium alloy, iridium/ 238 PuO 2 compatibility test, surface area measurements of 238 PuO 2 using the Blaine air permeability apparatus, and helium release from 238 PuO 2

Redefining design criteria for Pu-238 gloveboxes

International Nuclear Information System (INIS)

Acosta, S.V.

1998-01-01

Enclosures for confinement of special nuclear materials (SNM) have evolved into the design of gloveboxes. During the early stages of glovebox technology, established practices and process operation requirements defined design criteria. Proven boxes that performed and met or exceeded process requirements in one group or area, often could not be duplicated in other areas or processes, and till achieve the same success. Changes in materials, fabrication and installation methods often only met immediate design criteria. Standardization of design criteria took a big step during creation of ''Special-Nuclear Materials R and D Laboratory Project, Glovebox standards''. The standards defined design criteria for every type of process equipment in its most general form. Los Alamos National Laboratory (LANL) then and now has had great success with Pu-238 processing. However with ever changing Environment Safety and Health (ES and H) requirements and Ta-55 Facility Configuration Management, current design criteria are forced to explore alternative methods of glovebox design fabrication and installation. Pu-238 fuel processing operations in the Power Source Technologies Group have pushed the limitations of current design criteria. More than half of Pu-238 gloveboxes are being retrofitted or replaced to perform the specific fuel process operations. Pu-238 glovebox design criteria are headed toward process designed single use glovebox and supporting line gloveboxes. Gloveboxes that will house equipment and processes will support TA-55 Pu-238 fuel processing needs into the next century and extend glovebox expected design life

Hanford Site Transuranic (TRU) Waste Certification Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

2000-01-01

As a generator of transuranic (TRU) and TRU mixed waste destined for disposal at the Waste Isolation Pilot Plant (WIPP), the Hanford Site must ensure that its TRU waste meets the requirements of US. Department of Energy (DOE) 0 435.1, ''Radioactive Waste Management,'' and the Contact-Handled (CH) Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WIPP-WAC). WIPP-WAC requirements are derived from the WIPP Technical Safety Requirements, WIPP Safety Analysis Report, TRUPACT-II SARP, WIPP Land Withdrawal Act, WIPP Hazardous Waste Facility Permit, and Title 40 Code of Federal Regulations (CFR) 191/194 Compliance Certification Decision. The WIPP-WAC establishes the specific physical, chemical, radiological, and packaging criteria for acceptance of defense TRU waste shipments at WIPP. The WPP-WAC also requires that participating DOE TRU waste generator/treatment/storage sites produce site-specific documents, including a certification plan, that describe their program for managing TRU waste and TRU waste shipments before transferring waste to WIPP. Waste characterization activities provide much of the data upon which certification decisions are based. Waste characterization requirements for TRU waste and TRU mixed waste that contains constituents regulated under the Resource Conservation and Recovery Act (RCRA) are established in the WIPP Hazardous Waste Facility Permit Waste Analysis Plan (WAP). The Hanford Site Quality Assurance Project Plan (QAPjP) (HNF-2599) implements the applicable requirements in the WAP and includes the qualitative and quantitative criteria for making hazardous waste determinations. The Hanford Site must also ensure that its TRU waste destined for disposal at WPP meets requirements for transport in the Transuranic Package Transporter-11 (TRUPACT-11). The US. Nuclear Regulatory Commission (NRC) establishes the TRUPACT-11 requirements in the Safety Analysis Report for the TRUPACT-II Shipping Package (TRUPACT-11 SARP). In

Mechanical properties of 238PuO2

International Nuclear Information System (INIS)

Petrovic, J.J.; Hecker, S.S.; Land, C.C.; Rohr, D.L.

1977-04-01

The mechanical properties of 238 PuO 2 have been examined in the Los Alamos Scientific Laboratory mechanical test facility built to handle α-radioactive materials. Compression tests were conducted as a function of temperature, strain rate, grain size, density, and storage time. At temperatures less than or equal to 1400 0 C, test specimens of 238 PuO 2 exhibit pseudobrittle behavior due to internal cracks. Plastic deformation is ''localized'' at the crack tips. Generalized plastic deformation is observed at 1500 0 C. Ultimate stress values decrease markedly with increasing temperature and decreasing strain rate, and decrease less with decreasing density, increasing storage time, and increasing grain size. Room temperature fracture is transgranular, whereas intergranular fracture predominates at elevated temperatures. Crack-free specimens of 239 PuO 2 exhibit extensive plastic deformation at 1000 0 C and above. The relationship of these test results to the impact properties of 238 PuO 2 fuel in radioisotope thermoelectric generators is discussed

Transplacental absorption of 238Pu in rats and guinea pigs

International Nuclear Information System (INIS)

Sullivan, M.F.

1980-01-01

Pregnant rats and guinea pigs were injected intravenously with 238 Pu citrate to determine if the potential for in utero accumulation of 238 Pu by these two species is related to the stage of development at which immunity is gained. Although guinea pigs retained more 238 Pu after birth than rats, the difference was not significant

Interception and retention of 238Pu deposition by orange trees

International Nuclear Information System (INIS)

Pinder, J.E. III; Adriano, D.C.; Ciravolo, T.G.; Doswell, A.C.; Yehling, D.M.

1987-01-01

Radioisotope thermoelectric generators (RTG) transform the heat produced during the alpha decay of 238 Pu into electrical energy for use by deep-space probes, such as the Voyager spacecraft, which have returned images and other data from Jupiter, Saturn and Uranus. Future missions involving RTGs may be launched aboard the space shuttle, and there is a remote possibility that an explosion of liquid-hydrogen and liquid-oxygen fuel could rupture the RTGs and disperse 238 Pu into the atmosphere over central Florida. Research was performed to determine the potential transport to man of atmospherically dispersed Pu via contaminated orange fruits. The results indicate that the major contamination of oranges would result from the interception and retention of 238 Pu deposition by fruits. The resulting surface contamination could enter human food chains through transfer to internal tissues during peeling or in the reconstituted juices and flavorings made from orange skins. The interception of 238 Pu deposition by fruits is especially important because the results indicate no measurable loss of Pu from fruit surfaces through time or with washing. Approximately 1% of the 238 Pu deposited onto an orange grove would be harvested in the year following deposition

Savannah River Laboratory monthly report: 238Pu fuel form processes

International Nuclear Information System (INIS)

1976-01-01

Progress in the Savannah River 238 Pu Fuel Form Program is discussed. Goals of the Savannah River Laboratory (SRL) program are to provide technical support for the transfer of the 238 Pu fuel form fabrication operations from Mound Laboratory to new facilities being built at the Savannah River Plant (SRP), to provide the technical basis for 238 Pu scrap recovery at SRP, and to assist in sustaining plant operations. During the period it was found that the density of hot-pressed 238 PuO 2 pellets decreased as the particle size of ball-milled powder decreased;the surface area of calcined 238 PuO 2 powder increased with increasing precipitation temperature and may be related to the variation in ball-milling response observed among different H Area B-Line batches; calcined PuO 2 produced by Pu(III) reverse-strike precipitation was directly fabricated into a pellet without ball milling, slugging, or sharding. The pellet had good appearance with acceptable density and dimensional stability, and heat transfer measurements and calculations showed that the use of hollow aluminum sleeves in the plutonium fuel fabrication (PuFF) storage vault reduced the temperature of shipping cans to 170 0 C and will reduce the temperature at the center of pure plutonium oxide (PPO) spheres to 580 0 C

Toxicity of inhaled 238PuO2 II

International Nuclear Information System (INIS)

Muggenburg, B.A.; Mewhinney, J.A.; Merickel, B.S.; Boecker, B.B.; Hahn, F.F.; Guilmette, R.A.; Mauderly, J.L.; McClellan, R.O.

1980-01-01

Studies are in progress to determine dose-response relationships for inhaled 238 PuO 2 . Beagle dogs were given a single, brief, nose-only inhalation exposure to aerosols of monodisperse particles of 238 PuO 2 . Aerosols of two sizes were used, 1.5 μm aerodynamic diameter (AD) and 3.0 μm AD. Dogs were exposed to achieve initial lung burdens of 0.56, 0.28, 0.14, 0.07, 0.03 or 0.01 μCi 238 PuO 2 /kg body weight. Twelve dogs were exposed at each activity level to each aerosol particle size. The local dose around each 3.0 μm AD particle was 10 times higher than the local dose around 1.5 μm AD particles, but the dose averaged over the whole lung was the same at each activity level for both particle sizes. The lung retention of 238 Pu was divided into two phases of clearance. During the first 100 days after exposure, the average retention half-time for 238 Pu in the lung was 310 days. When the solubility changed due to particle breakup, the retention half-time decreased to 180 days during the period from 1OO to 1,500 days after exposure. The first biological effects observed were lymphopenia and neutropenia in peripheral blood. To date, 28 Beagle dogs have died at times from 536 to 1683 days after exposure. Initial lung burdens for the dead dogs ranged from 0.18 to 2.2 μCi 238 Pu/kg body weight. Nine died with radiation pneumonitis and pulmonary fibrosis, 10 died with lung tumors and 19 dogs died with bone tumors. There are 116 exposed and 22 control dogs surviving and under observation. Current patterns of dose versus response are discussed. (author)

Migration of plutonium from freshwater ecosystem at Hanford. [/sup 238/Pu, /sup 239/Pu, /sup 240/Pu

Energy Technology Data Exchange (ETDEWEB)

Emery, R. M.; Klopfer, D. C.; McShane, M. C.

1977-09-01

A reprocessing waste pond at Hanford has been inventoried to determine quantities of plutonium (Pu) that have been accumulated since its formation in 1944. Expressions of export were developed from these inventory data and from informed assumptions about the vectors which act to mobilize material containing Pu. This 14-acre pond provides a realistic illustration of the mobility of Pu in a lentic ecosystem. The ecological behavior of Pu in this pond is similar to that in other contaminated aquatic systems having widely differing limnological characteristics. Since its creation, this pond has received about one Ci of /sup 239/,/sup 240/Pu and /sup 238/Pu, most of which has been retained by its sediments. Submerged plants, mainly diatoms and Potamogeton, accumulate >95% of the Pu contained in biota. Emergent insects are the only direct biological route of export, mobilizing about 5 x 10/sup 3/ nCi of Pu annually, which is also the estimated maximum quantity of the Pu exported by waterfowl, birds and mammals collectively. There is no apparent significant export by wind, and it is not likely that Pu has migrated to the ground water below U-Pond via percolation. Although this pond has a rapid flushing rate, a eutrophic nutrient supply with a diverse biotic profile, and interacts with an active terrestrial environment, it appears to effectively bind Pu and prevent it from entering pathways to man and other life.

Radionuclide concentrations in soils and vegetation at radioactive-waste disposal Area G during the 1996 growing season. Progress report

International Nuclear Information System (INIS)

Fresquez, P.R.; Vold, E.L.; Naranjo, L. Jr.

1997-07-01

Soil and overstory and understory vegetation (washed and unwashed) collected at eight locations within and around Area G--a low-level radioactive solid-waste disposal facility at Los Alamos National laboratory--were analyzed for 3 H, 90 Sr, 238 Pu, 239 Pu, 137 Cs, 234 U, 235 U, 238 U, tot U, 228 Ac, 214 Bi, 60 Co, 40 K, 54 Mn, 22 Na, 214 Pb, and 208 Tl. Also, heavy metals (Ag, As, Ba, Be, Cd, Cr, Hg, Ni, Pb, Sb, Se, and Tl) in soil and vegetation were determined. In general, most radionuclide concentrations, with the exception of 3 H and 239 Pu, in soils and washed and unwashed overstory and understory vegetation collected from within and around Area G were within upper limit background concentrations. Tritium was detected as high as 14,744 pCi mL -1 in understory vegetation collected from transuranic (TRU) waste pad number-sign 4, and the TRU waste pad area contained the highest levels of 239 Pu in soils and in understory vegetation as compared to other areas at Area G

Nitrate Anion Exchange in Pu-238 Aqueous Scrap Recovery Operations

International Nuclear Information System (INIS)

Pansoy-Hjelvik, M.E.; Silver, G.L.; Reimus, M.A.H.; Ramsey, K.B.

1999-01-01

Strong base, nitrate anion exchange (IX) is crucial to the purification of 238 Pu solution feedstocks with gross levels of impurities. This paper discusses the work involved in bench scale experiments to optimize the nitrate anion exchange process. In particular, results are presented of experiments conducted to (a) demonstrate that high levels of impurities can be separated from 238 Pu solutions via nitrate anion exchange and, (b) work out chemical pretreatment methodology to adjust and maintain 238 Pu in the IV oxidation state to optimize the Pu(IV)-hexanitrato anionic complex sorption to Reillex-HPQ resin. Additional experiments performed to determine the best chemical treatment methodology to enhance recovery of sorbed Pu from the resin, and VIS-NIR absorption studies to determine the steady state equilibrium of Pu(IV), Pu(III), and Pu(VI) in nitric acid are discussed

RH-TRU Waste Content Codes

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2007-07-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

DOE's plan for buried transuranic (TRU) contaminated waste

International Nuclear Information System (INIS)

Mathur, J.; D'Ambrosia, J.; Sease, J.

1987-01-01

Prior to 1970, TRU-contaminated waste was buried as low-level radioactive waste. In the Defense Waste Management Plan issued in 1983, the plan for this buried TRU-contaminated waste was to monitor the buried waste, take remedial actions, and to periodically evaluate the safety of the waste. In March 1986, the General Accounting Office (GAO) recommended that the Department of Energy (DOE) provide specific plans and cost estimates related to buried TRU-contaminated waste. This plan is in direct response to the GAO request. Buried TRU-contaminated waste and TRU-contaminated soil are located in numerous inactive disposal units at five DOE sites. The total volume of this material is estimated to be about 300,000 to 500,000 m 3 . The DOE plan for TRU-contaminated buried waste and TRU-contaminated soil is to characterize the disposal units; assess the potential impacts from the waste on workers, the surrounding population, and the environment; evaluate the need for remedial actions; assess the remedial action alternatives; and implement and verify the remedial actions as appropriate. Cost estimates for remedial actions for the buried TRU-contaminated waste are highly uncertain, but they range from several hundred million to the order of $10 billion

Characterization optimization for the National TRU waste system

International Nuclear Information System (INIS)

Basabilvazo, George T.; Countiss, S.; Moody, D.C.; Jennings, S.G.; Lott, S.A.

2002-01-01

On March 26, 1999, the Waste Isolation Pilot Plant (WIPP) received its first shipment of transuranic (TRU) waste. On November 26, 1999, the Hazardous Waste Facility Permit (HWFP) to receive mixed TRU waste at WIPP became effective. Having achieved these two milestones, facilitating and supporting the characterization, transportation, and disposal of TRU waste became the major challenges for the National TRU Waste Program. Significant challenges still remain in the scientific, engineering, regulatory, and political areas that need to be addressed. The National TRU Waste System Optimization Project has been established to identify, develop, and implement cost-effective system optimization strategies that address those significant challenges. Fundamental to these challenges is the balancing and prioritization of potential regulatory changes with potential technological solutions. This paper describes some of the efforts to optimize (to make as functional as possible) characterization activities for TRU waste.

Analysis of plutonium isotope ratios including 238Pu/239Pu in individual U-Pu mixed oxide particles by means of a combination of alpha spectrometry and ICP-MS.

Science.gov (United States)

Esaka, Fumitaka; Yasuda, Kenichiro; Suzuki, Daisuke; Miyamoto, Yutaka; Magara, Masaaki

2017-04-01

Isotope ratio analysis of individual uranium-plutonium (U-Pu) mixed oxide particles contained within environmental samples taken from nuclear facilities is proving to be increasingly important in the field of nuclear safeguards. However, isobaric interferences, such as 238 U with 238 Pu and 241 Am with 241 Pu, make it difficult to determine plutonium isotope ratios in mass spectrometric measurements. In the present study, the isotope ratios of 238 Pu/ 239 Pu, 240 Pu/ 239 Pu, 241 Pu/ 239 Pu, and 242 Pu/ 239 Pu were measured for individual Pu and U-Pu mixed oxide particles by a combination of alpha spectrometry and inductively coupled plasma mass spectrometry (ICP-MS). As a consequence, we were able to determine the 240 Pu/ 239 Pu, 241 Pu/ 239 Pu, and 242 Pu/ 239 Pu isotope ratios with ICP-MS after particle dissolution and chemical separation of plutonium with UTEVA resins. Furthermore, 238 Pu/ 239 Pu isotope ratios were able to be calculated by using both the 238 Pu/( 239 Pu+ 240 Pu) activity ratios that had been measured through alpha spectrometry and the 240 Pu/ 239 Pu isotope ratios determined through ICP-MS. Therefore, the combined use of alpha spectrometry and ICP-MS is useful in determining plutonium isotope ratios, including 238 Pu/ 239 Pu, in individual U-Pu mixed oxide particles. Copyright © 2016 Elsevier B.V. All rights reserved.

238Pu fuel form activities, March 1-September 30, 1985

International Nuclear Information System (INIS)

1986-01-01

The SRP portion of this report summarizes production 238 PuO 2 fuel forms for use in radioisotopic thermoelectric generators (RTG's) in the Plutonium Fuel Form (PuFF) Facility at the Savannah River Plant. The PuFF Facility began producing iridium-encapsulated, 62.5-watt 238 PuO 2 right circular cylinders for GPHS (General Purpose Heat Source) RTG's in June 1980; this program was completed in December 1983. The PuFF Facility has been placed in a production readiness mode of operation pending funding of additional heat source programs

Distribution of 238Pu in tissues of fish from the canal in Miamisburg, Oho

International Nuclear Information System (INIS)

Kennedy, C.W.; Bartelt, G.E.

1978-01-01

The 238 Pu concentrations of varous tissues were measured for seven species of freshwater fish from an ecosystem containing elevated levels of 238 Pu. The highest levels of 238 Pu were found in the gastrointestinal tracts and gills, while the lowest levels were found in muscle tissue. A rapid uptake of 238 Pu was observed for hatchery bluegills introduced into this system. High plutonium concentrations in the gastrointestinal tracts and gills suggest that these organs are potential uptake sites. The presence of 238 Pu in certain tissues (liver, gonads, bone, and muscle) indicates that there is a translocation of 238 Pu from the uptake sites

Application of insoluble tannin to recovery of uranium, TRU and heavy metals elements form radioactive liquid waste

International Nuclear Information System (INIS)

Hamaguchi, Kazuhiko; Shirato, Wataru; Nakamura, Yasuo; Matsumura, Tatsuro; Takeshita, Kenji; Nakano, Yoshio

1999-01-01

Mitsubishi Nuclear Fuel Co., Ltd. (MNF) has developed a new adsorbent, TANNIX (tread mark), for the recovery of uranium, TRU and heavy metal elements in the liquid waste, in which TANNIX derived from a natural tannin polymer. TANNIX has same advantages that handling is easier than that of standard IX-resin, and that the volume of secondary waste is reduced by burning the used TANNIX. We have replaced its radioactive liquid waste treatment system from the conventional co-precipitation process to adsorption process by using TANNIX. TANNIX was founded to be more effective for the recovery of Pu, TRU, and hexavalent chromium Cr-(VI) as well as Uranium. (author)

Radionuclide concentrations in/on vegetation at radioactive-waste disposal Area G during the 1995 growing season. Progress report

International Nuclear Information System (INIS)

Fresquez, P.R.; Vold, E.L.; Naranjo, L. Jr.

1996-01-01

Overstory (pinon pine) and understory (grass and forb) vegetation were collected within and around selected points at Area G--a low- level radioactive solid-waste disposal facility at Los Alamos National Laboratory--for the analysis of tritium ( 3 H), strontium ( 90 Sr), plutonium ( 238 Pu and 239 Pu), cesium ( 137 Cs), and total uranium. Also, heavy metals (Ag, As, Ba, Be, Cd, Cr, Hg, Ni, Pb, Sb, Se, and Tl) in/on vegetation were determined. In general, most (unwashed) vegetation collected within and around Area G contained 3 H, uranium, 238 Pu, and 239 Pu in higher concentrations than vegetation collected from background areas. Tritium, in particular, was detected as high as 7300 pCi mL -1 in understory vegetation collected from the west side of the transuranic (TRU) pads. The south and west ends of the tritium shaft field also contained elevated levels of 3 H in overstory, and especially in understory vegetation, as compared to background; this suggests that 3 H may be migrating from this waste repository through surface and subsurface pathways. Also, understory vegetation collected north of the TRU pads (adjacent to the fence line of Area G) contained the highest values of 238 Pu and 239 Pu as compared to background, and may be a result of surface holding, storage, and/or disposal activities

Transuranic (TRU) Waste Phase I Retrieval Plan

CERN Document Server

McDonald, K M

2000-01-01

From 1970 to 1987, TRU and suspect TRU wastes at Hanford were placed in the SWBG. At the time of placement in the SWBG these wastes were not regulated under existing Resource Conservation and Recovery Act (RCRA) regulations, since they were generated and disposed of prior to the effective date of RCRA at the Hanford Site (1987). From the standpoint of DOE Order 5820.2A1, the TRU wastes are considered retrievably stored, and current plans are to retrieve these wastes for shipment to WIPP for disposal. This plan provides a strategy for the Phase I retrieval that meets the intent of TPA milestone M-91 and Project W-113, and incorporates the lessons learned during TRU retrieval campaigns at Hanford, LANL, and SRS. As in the original Project W-113 plans, the current plan calls for examination of approximately 10,000 suspect-TRU drums located in the 218-W-4C burial ground followed by the retrieval of those drums verified to contain TRU waste. Unlike the older plan, however, this plan proposes an open-air retrieval ...

Status of ERDA TRU waste packaging study

International Nuclear Information System (INIS)

Doty, J.W. Jr.

1977-01-01

This paper discusses the status of Task 3 of the TRU Waste Cyclone Drum Incinerator and Treatment System program. This task covers acceptable TRU packaging for interim storage and terminal isolation. The kind of TRU wastes generated by contractors and its transport are discussed. Both drum and box systems are desirable

238Pu concentrations in the marine environment at San Clemente Island

International Nuclear Information System (INIS)

Noshkin, V.E.; Brunk, J.L.; Jokela, T.A.; Wong, K.M.

1981-01-01

The concentration of plutonium and other radionuclides measured in samples of surface sediments, seawater and brown algae collected offshore from North Light Harbor Pier at San Clemente Island, CA, are presented. From 1967 to 1978, different forms of nuclear fuels used in operational or proposed SNAP (Systems for Nuclear Auxillary Power) devices were tested at this site to evaluate the effects of seawater on the heat sources. The principle radionuclide in the heat sources tested was 238 Pu. During these tests, small amounts of 238 Pu dissolved and migrated from the test chambers to the local marine environment. Currents dispersed this released 238 Pu so that at present a small increase in concentration above that of fallout background is evident in the surface 3.0-cm layer of near shore sediment that extends over a 3.0-km 2 area surrounding the pier. The 238 Pu associated with this sediment is slowly redissolving and can be taken up by marine algae. Except for a 0.025-km 2 region around the pier, the total plutonium ( 238 Pu + 239+240 Pu) in the surface 3.0-cm layer of sediment is within the range of total fallout plutonium reported in Atlantic and Pacific surface deposits from water depths less than 100 m. (author)

Preparation and characterization of 238Pu-ceramics for radiation damage experiments

International Nuclear Information System (INIS)

DM Strachan; RD Scheele; WC Buchmiller; JD Vienna; RL Sell; RJ Elovich

2000-01-01

As a result of treaty agreements between Russia and the US, portions of their respective plutonium and nuclear weapons stockpiles have been declared excess. In support of the US Department of Energy's 1998 decision to pursue immobilization of a portion of the remaining Pu in a titanate-based ceramic, the authors prepared nearly 200 radiation-damage test specimens of five Pu- and 238 Pu-ceramics containing 10 mass% Pu to determine the effects of irradiation from the contained Pu and U on the ceramic. The five Pu-ceramics were (1) phase-pure pyrochlore [ideally, Ca(U, Pu)Ti 2 O 7 ], (2) pyrochlore-rich baseline, (3) pyrochlore-rich baseline with impurities, (4) phase-pure zirconolite [ideally Ca(U, Pu)Ti 2 O 7 ], and (5) a zirconolite-rich baseline. These ceramics were prepared with either normal weapons-grade Pu, which is predominantly 239 Pu, or 238 Pu. The 238 Pu accelerates the radiation damage relative to the 239 Pu because of its much higher specific activity. The authors were unsuccessful in preparing phase-pure (Pu, U) brannerite, which is the third crystalline phase present in the baseline immobilization form. Since these materials will contain ∼10 mass% Pu and about 20 mass% U, radiation damage to the crystalline structure of these materials will occur overtime. As the material becomes damaged from the decay of the Pu and U, it is possible for the material to swell as both the alpha particles and recoiling atoms rupture chemical bonds within the solid. As the material changes density, cracking, perhaps in the form of microcracks, may occur. If cracking occurs in ceramic that has been placed in a repository, the calculated rate of radionuclide release if the can has corroded would increase proportionately to the increase in surface area. To investigate the effects of radiation damage on the five ceramics prepared, the authors are storing the specimens at 20, 125, and 250 C until the 238 Pu specimens become metamict and the damage saturates. They will

TRU waste transportation -- The flammable gas generation problem

International Nuclear Information System (INIS)

Connolly, M.J.; Kosiewicz, S.T.

1997-01-01

The Nuclear Regulatory Commission (NRC) has imposed a flammable gas (i.e., hydrogen) concentration limit of 5% by volume on transuranic (TRU) waste containers to be shipped using the TRUPACT-II transporter. This concentration is the lower explosive limit (LEL) in air. This was done to minimize the potential for loss of containment during a hypothetical 60 day period. The amount of transuranic radionuclide that is permissible for shipment in TRU waste containers has been tabulated in the TRUPACT-II Safety Analysis Report for Packaging (SARP, 1) to conservatively prevent accumulation of hydrogen above this 5% limit. Based on the SARP limitations, approximately 35% of the TRU waste stored at the Idaho National Engineering and Environmental Lab (INEEL), Los Alamos National Lab (LANL), and Rocky Flats Environmental Technology Site (RFETS) cannot be shipped in the TRUPACT-II. An even larger percentage of the TRU waste drums at the Savannah River Site (SRS) cannot be shipped because of the much higher wattage loadings of TRU waste drums in that site's inventory. This paper presents an overview of an integrated, experimental program that has been initiated to increase the shippable portion of the Department of Energy (DOE) TRU waste inventory. In addition, the authors will estimate the anticipated expansion of the shippable portion of the inventory and associated cost savings. Such projection should provide the TRU waste generating sites a basis for developing their TRU waste workoff strategies within their Ten Year Plan budget horizons

Optimization of hybrid-type instrumentation for Pu accountancy of U/TRU ingot in pyroprocessing.

Science.gov (United States)

Seo, Hee; Won, Byung-Hee; Ahn, Seong-Kyu; Lee, Seung Kyu; Park, Se-Hwan; Park, Geun-Il; Menlove, Spencer H

2016-02-01

One of the final products of pyroprocessing for spent nuclear fuel recycling is a U/TRU ingot consisting of rare earth (RE), uranium (U), and transuranic (TRU) elements. The amounts of nuclear materials in a U/TRU ingot must be measured as precisely as possible in order to secure the safeguardability of a pyroprocessing facility, as it contains the most amount of Pu among spent nuclear fuels. In this paper, we propose a new nuclear material accountancy method for measurement of Pu mass in a U/TRU ingot. This is a hybrid system combining two techniques, based on measurement of neutrons from both (1) fast- and (2) thermal-neutron-induced fission events. In technique #1, the change in the average neutron energy is a signature that is determined using the so-called ring ratio method, according to which two detector rings are positioned close to and far from the sample, respectively, to measure the increase of the average neutron energy due to the increased number of fast-neutron-induced fission events and, in turn, the Pu mass in the ingot. We call this technique, fast-neutron energy multiplication (FNEM). In technique #2, which is well known as Passive Neutron Albedo Reactivity (PNAR), a neutron population's changes resulting from thermal-neutron-induced fission events due to the presence or absence of a cadmium (Cd) liner in the sample's cavity wall, and reflected in the Cd ratio, is the signature that is measured. In the present study, it was considered that the use of a hybrid, FNEM×PNAR technique would significantly enhance the signature of a Pu mass. Therefore, the performance of such a system was investigated for different detector parameters in order to determine the optimal geometry. The performance was additionally evaluated by MCNP6 Monte Carlo simulations for different U/TRU compositions reflecting different burnups (BU), initial enrichments (IE), and cooling times (CT) to estimate its performance in real situations. Copyright © 2015 Elsevier Ltd. All

Comparative assessment of TRU waste forms and processes. Volume I. Waste form and process evaluations

International Nuclear Information System (INIS)

Ross, W.A.; Lokken, R.O.; May, R.P.; Roberts, F.P.; Timmerman, C.L.; Treat, R.L.; Westsik, J.H. Jr.

1982-09-01

This study provides an assesses seven waste forms and eight processes for immobilizing transuranic (TRU) wastes. The waste forms considered are cast cement, cold-pressed cement, FUETAP (formed under elevated temperature and pressure) cement, borosilicate glass, aluminosilicate glass, basalt glass-ceramic, and cold-pressed and sintered silicate ceramic. The waste-immobilization processes considered are in-can glass melting, joule-heated glass melting, glass marble forming, cement casting, cement cold-pressing, FUETAP cement processing, ceramic cold-pressing and sintering, basalt glass-ceramic processing. Properties considered included gas generation, chemical durability, mechanical strength, thermal stability, and radiation stability. The ceramic products demonstrated the best properties, except for plutonium release during leaching. The glass and ceramic products had similar properties. The cement products generally had poorer properties than the other forms, except for plutonium release during leaching. Calculations of the Pu release indicated that the waste forms met the proposed NRC release rate limit of 1 part in 10 5 per year in most test conditions. The cast-cement process had the lowest processing cost, followed closely by the cold-pressed and FUETAP cement processes. Joule-heated glass melting had the lower cost of the glass processes. In-can melting in a high-quality canister had the highest cost, and cold-pressed and sintered ceramic the second highest. Labor and canister costs for in-can melting were identified. The major contributor to costs of disposing of TRU wastes in a defense waste repository is waste processing costs. Repository costs could become the dominant cost for disposing of TRU wastes in a commercial repository. It is recommended that cast and FUETAP cement and borosilicate glass waste-form systems be considered. 13 figures, 16 tables

Transuranic (TRU) Waste Phase I Retrieval Plan

International Nuclear Information System (INIS)

MCDONALD, K.M.

1999-01-01

From 1970 to 1987, TRU and suspect TRU wastes at Hanford were placed in the SWBG. At the time of placement in the SWBG these wastes were not regulated under existing Resource Conservation and Recovery Act (RCRA) regulations, since they were generated and disposed of prior to the effective date of RCRA at the Hanford Site (1987). From the standpoint of DOE Order 5820.2A', the TRU wastes are considered retrievably stored, and current plans are to retrieve these wastes for shipment to WIPP for disposal. This plan provides a strategy for the Phase I retrieval that meets the intent of TPA milestone M-91 and Project W-113, and incorporates the lessons learned during TRU retrieval campaigns at Hanford, LANL, and SRS. As in the original Project W-I13 plans, the current plan calls for examination of approximately 10,000 suspect-TRU drums located in the 218-W-4C burial ground followed by the retrieval of those drums verified to contain TRU waste. Unlike the older plan, however, this plan proposes an open-air retrieval scenario similar to those used for TRU drum retrieval at LANL and SRS. Phase I retrieval consists of the activities associated with the assessment of approximately 10,000 55-gallon drums of suspect TRU-waste in burial ground 218-W-4C and the retrieval of those drums verified to contain TRU waste. Four of the trenches in 218-W-4C (Trenches 1,4,20, and 29) are prime candidates for Phase I retrieval because they contain large numbers of suspect TRU drums, stacked from 2 to 5 drums high, on an asphalt pad. In fact, three of the trenches (Trenches 1,20, and 29) contain waste that has not been covered with soil, and about 1500 drums can be retrieved without excavation. The other three trenches in 218-W-4C (Trenches 7, 19, and 24) are not candidates for Phase I retrieval because they contain significant numbers of boxes. Drums will be retrieved from the four candidate trenches, checked for structural integrity, overpacked, if necessary, and assayed at the burial

Transuranic (TRU) Waste Phase I Retrieval Plan

International Nuclear Information System (INIS)

MCDONALD, K.M.

2000-01-01

From 1970 to 1987, TRU and suspect TRU wastes at Hanford were placed in the SWBG. At the time of placement in the SWBG these wastes were not regulated under existing Resource Conservation and Recovery Act (RCRA) regulations, since they were generated and disposed of prior to the effective date of RCRA at the Hanford Site (1987). From the standpoint of DOE Order 5820.2A1, the TRU wastes are considered retrievably stored, and current plans are to retrieve these wastes for shipment to WIPP for disposal. This plan provides a strategy for the Phase I retrieval that meets the intent of TPA milestone M-91 and Project W-113, and incorporates the lessons learned during TRU retrieval campaigns at Hanford, LANL, and SRS. As in the original Project W-113 plans, the current plan calls for examination of approximately 10,000 suspect-TRU drums located in the 218-W-4C burial ground followed by the retrieval of those drums verified to contain TRU waste. Unlike the older plan, however, this plan proposes an open-air retrieval scenario similar to those used for TRU drum retrieval at LANL and SRS. Phase I retrieval consists of the activities associated with the assessment of approximately 10,000 55-gallon drums of suspect TRU-waste in burial ground 218-W-4C and the retrieval of those drums verified to contain TRU waste. Four of the trenches in 218-W-4C (Trenches 1, 4, 20, and 29) are prime candidates for Phase I retrieval because they contain large numbers of suspect TRU drums, stacked from 2 to 5 drums high, on an asphalt pad. In fact, three of the trenches (Trenches 1 , 20, and 29) contain waste that has not been covered with soil, and about 1500 drums can be retrieved without excavation. The other three trenches in 218-W-4C (Trenches 7, 19, and 24) are not candidates for Phase I retrieval because they contain significant numbers of boxes. Drums will be retrieved from the four candidate trenches, checked for structural integrity, overpacked, if necessary, and assayed at the burial

Distribution of 238Pu and 239240Pu in aquatic macrophytes from a midwestern watershed

International Nuclear Information System (INIS)

Wayman, C.W.; Bartelt, G.E.; Alberts, J.J.

1977-01-01

Aquatic macrophytes were collected in the Great Miami River, Ohio, above and below Miamisburg and in the canal and ponds, near the Mound Laboratory, which contain sediments of a high activity (approximately 10 3 to 10 6 times) relative to the river sediments. Macrophytes collected in the river below Miamisburg have higher activities of 238 Pu than those collected from above the city. Macrophytes from the canal and ponds contain high specific activities of 238 Pu and 239 , 240 Pu with the exception of cattails grown in the ponds. Concentration factors are reported and discussed with reference to possible modes of plutonium accumulation and distribution within the plants

An approach for the reasonable TRU waste management in NUCEF

International Nuclear Information System (INIS)

Mineo, H.; Dojiri, S.; Takeshita, I.; Tsujino, T.; Matsumura, T.; Nishizawa, I.; Sugikawa, S.

1995-01-01

The Nuclear Fuel Cycle Safety Engineering Research Facility (NUCEF) has started its hot operation at the beginning of 1995, where TRU (transuranic) elements are used. The management of TRU waste arisen in the facility is very important issue. Liquid and solid wastes containing TRU elements are generated mainly from the Fuel Treatment System for critical experiments and from the researches of reprocessing process and TRU waste management for reprocessing plants using hot cells and glove-boxes. The TRU waste management in NUCEF is based on the classification of waste, and is to maximize the recycle of reagents and the reuse of TRU elements separated from the waste, as well as to reduce the waste volume and to lower the risk of waste by advanced separation and solidification. In the future, the separation and solidification of TRU elements in the tanks of liquid waste, and the classification and discrimination of solid wastes, will be carried out applying the outcomes of the development by the researches in NUCEF. (authors)

Disposition of 238Pu(NO3)4 following inhalation by beagle dogs

International Nuclear Information System (INIS)

Dagle, G.E.; Cannon, W.C.; Schirmer, R.E.; Stevens, D.L. Jr.

1979-01-01

Twelve dogs were given a single inhalation exposure to 238 Pu(NO 3 ) 4 to study deposition and translocation up to 1 yr. Preliminary data suggest a greater and more rapid translocation of 238 Pu(NO 3 ) 4 to bone and liver than was observed for 239 Pu(NO 3 ) 4

TRU waste inventory collection and work-off plans for the centralization of TRU waste characterization at INL - on your mark - get set - 9410

International Nuclear Information System (INIS)

Mctaggert, Jerri Lynne; Lott, Sheila; Gadbury, Casey

2009-01-01

The U.S. Department of Energy (DOE) amended the Record of Decision (ROD) for the Waste Management Program: Treatment and Storage ofTransuranic Waste to centralize transuranic (TRU) waste characterization/certification from fourteen TRU waste sites. This centralization will allow for treatment, characterization and certification ofTRU waste from the fourteen sites, thirteen of which are sites with small quantities ofTRU waste, at the Idaho National Laboratory (INL) prior to shipping the waste to the Waste Isolation Pilot Plant (WIPP) for disposal. Centralization ofthis TRU waste will avoid the cost ofbuilding treatment, characterization, certification, and shipping capabilities at each ofthe small quantity sites that currently do not have existing facilities. Advanced Mixed Waste Treatment Project (AMWTP) and Idaho Nuclear Technology and Engineering Center (INTEC) will provide centralized shipping facilities, to WIPP, for all ofthe small quantity sites. Hanford, the one large quantity site identified in the ROD, has a large number ofwaste in containers that are overpacked into larger containers which are inefficient for shipment to and disposal at WIPP. The AMWTP at the INL will reduce the volume ofmuch of the CH waste and make it much more efficient to ship and dispose of at WIPP. In addition, the INTEC has a certified remote handled (RH) TRU waste characterization/certification program at INL to disposition TRU waste from the sites identified in the ROD.

Development of a safe TRU transportation system (STRUTS) for DOE's TRU waste

International Nuclear Information System (INIS)

Edling, D.A.; Hopkins, D.R.; Walls, H.C.

1978-01-01

Transportation, the link between TRU waste generation and WIPP (Waste Isolation Pilot Project) and a vital link in the overall TRU waste management program, must be addressed. The program must have many facets: ensuring public and carrier acceptance, formation of a functional and current transportation data base, systems integration, maximum utilization of existing technology, and effective implementation and integration of the transport system into current and planned operational systems

A proposed new mission for producing 238Pu at the Hanford site

International Nuclear Information System (INIS)

Cash, R.J.

1989-01-01

A new mission for producing 238 Pu has been proposed at the Hanford site. If approved, the program would produce 238 Pu for National Aeronautics and Space Administration (NASA) space missions and possibly other speciality isotopes for medical and industrial applications. The 238 Pu isotope is an excellent heat source and is currently used in generating electricity for deep-space applications. To produce 238 Pu, special neptunium target assemblies would be irradiated for ∼2 yr in the Fast Flux Test Facility (FFTF) operated by Westinghouse Handford Company. After ∼1 yr of cooling, the neptunium pins would be reprocessed in special hot cells in the Fuel and Materials Examination Facility (FMEF) at the Hanford site to recover the 238 Pu and convert it into the oxide form. The oxide could then be encapsulated in the FMEF using special materials and procedures to meet rigid NASA requirements. The plutonium oxide capsules would later become part of the radioisotope thermoelectric generators used by NASA to power equipment launched into space. To meet projected NASA mission requirements, the program would provide the capability to recover up to 30 kg/yr of 238 Pu from 237 Np targets by late 1993. The conceptual design for the program was completed by Westinghouse Hanford in September 1989 for validation and approval by the U.S. Department of Energy

RH-TRU Waste Content Codes (RH-Trucon)

International Nuclear Information System (INIS)

2007-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is '3.' The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR limits based

RH-TRU Waste Content Codes (RH-TRUCON)

International Nuclear Information System (INIS)

2007-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is '3.' The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR limits based

RH-TRU Waste Content Codes (RH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-08-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

RH-TRU Waste Content Codes (RH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2007-05-30

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

RH-TRU Waste Content Codes (RH TRUCON)

International Nuclear Information System (INIS)

2007-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: (1) A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. (2) A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is ''3''. The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

RH-TRU Waste Content Codes (RH TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2007-05-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

TRU Waste Inventory Collection and Work-Off Plans for the Centralization of TRU Waste Characterization/Certification at INL - On Your Mark - Get Set

International Nuclear Information System (INIS)

McTaggart, J.; Lott, S.

2009-01-01

The U.S. Department of Energy (DOE) amended the Record of Decision (ROD) for the Waste Management Program: Treatment and Storage of Transuranic Waste to centralize transuranic (TRU) waste characterization/certification from fourteen TRU waste sites. This centralization will allow for treatment, characterization and certification of TRU waste from the fourteen sites, thirteen of which are sites with small quantities of TRU waste, at the Idaho National Laboratory (INL) prior to shipping the waste to the Waste Isolation Pilot Plant (WIPP) for disposal. Centralization of this TRU waste will avoid the cost of building treatment, characterization, certification, and shipping capabilities at each of the small quantity sites that currently do not have existing facilities. Advanced Mixed Waste Treatment Project (AMWTP) and Idaho Nuclear Technology and Engineering Center (INTEC) will provide centralized shipping facilities, to WIPP, for all of the small quantity sites. Hanford, the one large quantity site identified in the ROD, has a large number of waste in containers that are over-packed into larger containers which are inefficient for shipment to and disposal at WIPP. The AMWTP at the INL will reduce the volume of much of the CH waste and make it much more efficient to ship and dispose of at WIPP. In addition, the INTEC has a certified remote handled (RH) TRU waste characterization/certification program at INL to disposition TRU waste from the sites identified in the ROD. (authors)

Solubility of reactor fuels in the mouse lung with respect to their U/Pu and 238Pu/239Pu ratios

International Nuclear Information System (INIS)

Talbot, R.J.; Baker, S.T.

1989-01-01

The studies reported were designed to assess the comparative in vivo solubilities of a range of plutonium containing reactor fuels. To simulate these fuels, mixed U/Pu oxides were prepared and calcined at 1600 0 C. A plutonium content of 3% w/w was chosen as typical of water-cooled reactor fuel. Higher concentrations of plutonium (10, 20 and 30%) were included to simulate fast reactor fuel. As it is known that 238 PuO 2 , with high specific activity, is translocated more rapidly from lung than 239 PuO 2 , the effect of isotopic composition of plutonium in simulated reactor fuels was also investigated. For this purpose, both the water-cooled and fast-reactor fuels were prepared with plutonium containing 2% of 238 Pu by weight. The resulting oxides had about 6 times the specific activity of those prepared with 239 Pu. Groups of mice were killed at 1, 3, 6, 12 and 18 months after inhaling aerosols of the simulated reactor fuels. After 3 months, measurements of Pu retention in the lung showed no marked differences between materials. After 6 months, measurements of plutonium deposited in the liver and skeleton showed that mixed U/Pu oxides were more soluble in vivo than 239 PuO 2 . Their solubility was inversely related to their plutonium content. The addition of 238 Pu to the plutonium resulted in enhanced translocation of plutonium from the lung, in the cases of water-cooled reactor fuel by a factor of two. (author)

Plans for Managing Hanford Remote Handled Transuranic (TRU) Waste

International Nuclear Information System (INIS)

MCKENNEY, D.E.

2001-01-01

The current Hanford Site baseline and life-cycle waste forecast predicts that approximately 1,000 cubic meters of remote-handled transuranic (RH-TRU) waste will be generated by waste management and environmental restoration activities at Hanford. These 1,000 cubic meters, comprised of both transuranic and mixed transuranic (TRUM) waste, represent a significant portion of the total estimated inventory of RH-TRU to be disposed of at the Waste Isolation Pilot Plant (WIPP). A systems engineering approach is being followed to develop a disposition plan for each RH-TRU/TRUM waste stream at Hanford. A number of significant decision-making efforts are underway to develop and finalize these disposition plans, including: development and approval of a RH-TRU/TRUM Waste Project Management Plan, revision of the Hanford Waste Management Strategic Plan, the Hanford Site Options Study (''Vision 2012''), the Canyon Disposal Initiative Record-of-Decision, and the Hanford Site Solid (Radioactive and Hazardous) Waste Program Environmental Impact Statement (SW-EIS). Disposition plans may include variations of several options, including (1) sending most RH-TRU/TRUM wastes to WIPP, (2) deferrals of waste disposal decisions in the interest of both efficiency and integration with other planned decision dates and (3) disposition of some materials in place consistent with Department of Energy Orders and the regulations in the interest of safety, risk minimization, and cost. Although finalization of disposition paths must await completion of the aforementioned decision documents, significant activities in support of RH-TRU/TRUM waste disposition are proceeding, including Hanford participation in development of the RH TRU WIPP waste acceptance criteria, preparation of T Plant for interim storage of spent nuclear fuel sludge, sharing of technology information and development activities in cooperation with the Mixed Waste Focus Area, RH-TRU technology demonstrations and deployments, and

Hematological responses after inhaling 238PuO2: An extrapolation from beagle dogs to humans

International Nuclear Information System (INIS)

Scott, B.R.; Muggenburg, B.A.; Welsh, C.A.; Angerstein, D.A.

1994-01-01

The alpha emitter plutonium-238 ( 238 Pu), which is produced in uranium-fueled, light-water reactors, is used as a thermoelectric power source for space applications. Inhalation of a mixed oxide form of Pu is the most likely mode of exposure of workers and the general public. Occupational exposures to 238 PuO 2 have occurred in association with the fabrication of radioisotope thermoelectric generators. Organs and tissue at risk for deterministic and stochastic effects of 238 Pu-alpha irradiation include the lung, liver, skeleton, and lymphatic tissue. Little has been reported about the effects of inhaled 238 PuO 2 on peripheral blood cell counts in humans. The purpose of this study was to investigate hematological responses after a single inhalation exposure of Beagle dogs to alpha-emitting 238 PuO 2 particles and to extrapolate results to humans

Thermal treatment for TRU waste sorting

International Nuclear Information System (INIS)

Sasaki, Toshiki; Aoyama, Yoshio; Yamashita, Toshiyuki

2009-03-01

A thermal treatment that can automatically unpack TRU waste and remove hazardous materials has been developed to reduce the risk of radiation exposure and save operation cost. The thermal treatment is a process of removing plastic wrapping and hazardous material from TRU waste by heating waste at 500 to 700degC. Plastic wrappings of simulated wastes were removed using a laboratory scale thermal treatment system. Celluloses and isoprene rubbers that must be removed from waste for disposal were pyrolyzed by the treatment. Although the thermal treatment can separate lead and aluminum from the waste, a further technical development is needed to separate lead and aluminum. A demonstration scale thermal treatment system that comprises a rotary kiln with a jacket water cooler and a rotating inner cage for lead and aluminum separation is discussed. A clogging prevention system against zinc chloride, a lead and aluminum accumulation system, and a detection system for spray cans that possibly cause explosion and fire are also discussed. Future technology development subjects for the TRU waste thermal treatment system are summarized. (author)

Transuranic (TRU) waste management at Savannah River - past, present and future

International Nuclear Information System (INIS)

D'Ambrosia, J.T.

1985-01-01

Defense TRU waste at Savannah River (SR) results from the Department of Energy's (DOE) national defense activities, including the operation of production reactors and fuel reprocessing plants and research and development activities. TRU waste is material declared as having negligible economic value, contaminated with alpha-emitting radionuclides of atomic number greater than 92, and half-lives longer than 20 years, in concentrations greater than 100 nCi/g. TRU waste has been retrievably stored at SR since 1974 awaiting disposal. The Waste Isolation Pilot Plant (WIPP), now under construction in New Mexico, is a research and development facility for demonstrating the safe disposal of defense TRU waste, including that in storage at SR. The major objective of the TRU program at SR is to support the TRU National Program, which is dedicated to preparing waste for, and emplacing waste in, the WIPP. Thus, the SR Program also supports WIPP operations. The SR Site specific goals are to phase out the indefinite storage of TRU waste, which has been the mode of waste management since 1974, and to dispose of SR's Defense TRU waste

TRU waste form and package criteria meeting

Energy Technology Data Exchange (ETDEWEB)

None

1977-08-01

The broad subject of the meeting is the overall ERDA TRU waste management program, although the discussions also cover performance criteria for the Waste Isolation Pilot Plant and their implications for the overall TRU program. Separate abstracts were prepared for all ten presentations. (DLC)

Neutron inelastic-scattering cross sections of 232Th, 233U, 235U, 238U, 239Pu and 240Pu

International Nuclear Information System (INIS)

Smith, A.B.; Guenther, P.T.

1982-01-01

Differential-neutron-emission cross sections of 232 Th, 233 U, 235 U, 238 U, 239 Pu and 240 Pu are measured between approx. = 1.0 and 3.5 MeV with the angle and magnitude detail needed to provide angle-integrated emission cross sections to approx. 232 Th, 233 U, 235 U and 238 U inelastic-scattering values, poor agreement is observed for 240 Pu, and a serious discrepancy exists in the case of 239 Pu

Studies of transuranic waste storage under conditions expected in the Waste Isolation Pilot Plant (WIPP). Interim summary report, October 1, 1977-June 15, 1979

International Nuclear Information System (INIS)

Kosiewicz, S.T.; Barraclough, B.L.; Zerwekh, A.

1980-01-01

The major focus of the program has been on the gas generation potential of organic wastes produced by radiolytic and thermal degradation under simulated WIPP storage conditions. The effects of TRU contamination level, temperature, waste type, pressure, and exposure time on radiolysis are presented. In addition, results from preliminary experiments on processed sludge dewatering are discussed. A summary is presented here of the results of a detailed study of all retrievably stored TRU wastes present at LASL before January 1, 1978. The data indicate a gross volume for the LASL inventory of 1610 m 3 with a total weight of nearly 1.24 x 10 6 kg (1240 metric tonnes). The dominant radionuclide contents of the waste are plutonium (primarily 238 Pu) and americium

Transmutation of 129I, 237Np, 238Pu, 239Pu, and 241Am using ...

Indian Academy of Sciences (India)

Results of transmutation studies of 129I, 237Np, 238Pu, 239Pu and 241Am are presented. Keywords. ... J Adam et al. Table 1. Samples properties for 0.7 and 1 GeV experiments. ..... If we suppose that this conclusion is true also for ratios in ...

Surrogate measurement of the 238Pu(n,f) cross section

International Nuclear Information System (INIS)

Ressler, J. J.; Burke, J. T.; Escher, J. E.; Bernstein, L. A.; Bleuel, D. L.; Casperson, R. J.; Gostic, J.; Henderson, R.; Scielzo, N. D.; Thompson, I. J.; Wiedeking, M.; Angell, C. T.; Goldblum, B. L.; Munson, J.; Basunia, M. S.; Phair, L. W.; Beausang, C. W.; Hughes, R. O.; Hatarik, R.; Ross, T. J.

2011-01-01

The neutron-induced fission cross section of 238 Pu was determined using the surrogate ratio method. The (n,f) cross section over an equivalent neutron energy range 5-20 MeV was deduced from inelastic α-induced fission reactions on 239 Pu, with 235 U(α,α ' f) and 236 U(α,α ' f) used as references. These reference reactions reflect 234 U(n,f) and 235 U(n,f) yields, respectively. The deduced 238 Pu(n,f) cross section agrees well with standard data libraries up to ∼10 MeV, although larger values are seen at higher energies. The difference at higher energies is less than 20%.

²³⁸PuO₂ Fuel and Dosimetry

Energy Technology Data Exchange (ETDEWEB)

Mayo, Douglas R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rawool-Sullivan, Mohini [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Garner, Scott Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Wenz, Tracy R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Karpius, Peter Joseph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-06-01

²³⁸Pu is an ideal material for use as a heat source with its half-life of 87.7 years and copious particle emissions. ²³⁸Pu radioisotope thermoelectric generators (RTGs) have found use for pacemakers, Apollo Space missions, Mars rovers, and Voyager spacecraft. In evaluating the dose to personnel and components near a ²³⁸Pu-based RTG, a number of additional nuclides and their daughter products must be considered to get an accurate estimate for γ-dose, and the amount of ¹⁷O and ¹⁸O for the neutron-dose must be considered. This paper looks at the contributing nuclides and their daughter products that add the most to the dose rates.

Development of techniques for measuring plutonium contents in TRU wastes by NDA methods

International Nuclear Information System (INIS)

Matsubayashi, Toshiyuki; Kuwana, Katsumi; Morita, Tomio; Izuhara, Shigeomi; Suzuki, Masahiro

1983-01-01

In order to develop a technique for measuring the amount of plutonium in plutonium-contaminated (TRU) wastes, a passive gamma method was selected from many candidate methods, and examined for the suitability by applying the method to low density wastes. A segmented gamma scanner was used for the experiment. The instrument is composed mainly of a Ge(Li) detector, multichannel analyser, data processing system, turntable and transmission radiation source of (75)Se. A sham waste was prepared by adding plutonium oxide powder as a radiation source to waste matrix in a 20-1 carton box. The sham waste was put on the turntable, and the detector was set at 50 cm distance from the center of the turntable. 414 keV gamma ray emitted from (239)Pu was utilized for the assay of plutonium in the experiment. The effects of combustible (paper) waste matrix, organic chlorinated material matrix, and the distribution of plutonium source in a box on the count rate were examined, and it was concluded that 1) about 10 mg of (239)Pu contained in both matrices should be assayed by the passive gamma method, 2) 50 mg of (239) Pu was measured at 30 % confidence level with 2000 sec measuring time, 3) the effect of distribution of plutonium in a waste was able to be reduced to a value of less than 15 % by rotating the waste on the turntable. (Yoshitake, I.)

Leaching of solidified TRU-contaminated incinerator ash

International Nuclear Information System (INIS)

Fuhrmann, M.; Colombo, P.

1984-01-01

Leach rate and cumulative fractional releases of plutonium were determined for a series of laboratory-scale waste forms containing transuranic (TRU) contaminated incinerator ash. The solidification agents from which these waste forms were produced are commercially available materials for radioactive waste disposal. The leachants simulate groundwaters with chemical compositions that are indiginous to different geological media proposed for repositories. In this study TRU-contaminated ash was incorporated into waste forms fabricated with portland type I cement, urea-formaldehyde, polyester-styrene or Pioneer 221 bitumen. The ash was generated at the dual-chamber incinerator at the Rocky Flats Plant. These waste forms contained between 1.25 x 10 -2 and 4.4 x 10 -2 Ci (depending on the solidification agent) of mixed TRU isotopes comprised primarily of 239 Pu and 240 Pu. Five leachant solutions were prepared consisting of: (1) demineralized water, (2) simulated brine, (3) simplified sodium-dominated groundwater (30 meq NaCl/liter), (4) simplified calcium-dominated groundwater (30 meq CaCl 2 /liter), and (5) simplified bicarbonate-dominated groundwater (30 meq NaHCO 3 /liter). Cumulative fractional releases were found to vary significantly with different leachants and solidification agents. In all cases waste forms leached in brine gave the lowest leach rates. Urea-formaldehyde had the greatest release of radionuclides while polyester-styrene and portland cement had approximately equivalent fractional releases. Cement cured for 210 days retained radionuclides three times more effectively than cement cured only 30 days

Effect of microdose distribution on chromosome aberration frequency in liver cells of the Chinese hamster following exposure to 239PuO2 or 238PuO2 particles

International Nuclear Information System (INIS)

Brooks, A.L.; Peters, R.F.; Retherford, J.C.

1974-01-01

Chinese hamsters were injected intravenously with 239 PuO 2 or 238 PuO 2 particles of known size or with 238 Pu citrate to determine the effect of particle size and specific activity on the frequency and distribution of chromosome damage in the liver. Three particle sizes were used in the 239 PuO 2 experiment: 0.15, 0.44, and 0.89 μm, and all animals were injected with a constant activity, 5 x 10 -4 muCi 239 Pu/gm body weight. The 238 PuO 2 was injected in three particle sizes, 0.17, 0.41, and 1.1 μm and at three activity levels. The 238 Pu citrate was injected at 5 x 10 -3 muCi 238 Pu/gm body weight. Hamsters injected with 239 PuO 2 were sacrificed at 15, 42, and 122 days after injection and those injected with either 238 PuO 2 or 238 Pu citrate were sacrificed 12 days after injection. The number of alpha tracks/star increased as a function of the particle size injected. A change in particle size with time was noted as smaller particles were aggregated into larger ones by the phagocytic action of Kupffer cells. Injection of 239 PuO 2 and 238 PuO 2 produced a distribution of chromosome damage which was non-poison in nature. 239 PuO 2 produced increased damage with increasing average dose with some cells containing a large number of aberrations, but there was relatively little particle size effect. Conversely, aberration frequencies after 238 PuO 2 injection were inversely related to particle size and no cells were seen with large amounts of damage. The 238 Pu citrate produced 6 x 10 -3 aberrations/cell/rad which was a higher rate than observed for 238 Pu particles. Risk for the production of cellular damage in the liver was greater per μCi following injection of either 238 Pu or 239 Pu citrate than it was following deposition of the same amount of 239 PuO 2 or 238 PuO 2 particles. (U.S.)

Final Hanford Site Transuranic (TRU) Waste Characterization QA Project Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

2000-01-01

The Quality Assurance Project Plan (QAPjP) has been prepared for waste characterization activities to be conducted by the Transuranic (TRU) Project at the Hanford Site to meet requirements set forth in the Waste Isolation Pilot Plan (WIPP) Hazardous Waste Facility Permit, 4890139088-TSDF, Attachment B, including Attachments B1 through B6 (WAP) (DOE, 1999a). The QAPjP describes the waste characterization requirements and includes test methods, details of planned waste sampling and analysis, and a description of the waste characterization and verification process. In addition, the QAPjP includes a description of the quality assurance/quality control (QA/QC) requirements for the waste characterization program. Before TRU waste is shipped to the WIPP site by the TRU Project, all applicable requirements of the QAPjP shall be implemented. Additional requirements necessary for transportation to waste disposal at WIPP can be found in the ''Quality Assurance Program Document'' (DOE 1999b) and HNF-2600, ''Hanford Site Transuranic Waste Certification Plan.'' TRU mixed waste contains both TRU radioactive and hazardous components, as defined in the WLPP-WAP. The waste is designated and separately packaged as either contact-handled (CH) or remote-handled (RH), based on the radiological dose rate at the surface of the waste container. RH TRU wastes are not currently shipped to the WIPP facility

The Advantages of Fixed Facilities in Characterizing TRU Wastes

International Nuclear Information System (INIS)

FRENCH, M.S.

2000-01-01

In May 1998 the Hanford Site started developing a program for characterization of transuranic (TRU) waste for shipment to the Waste Isolation Pilot Plant (WIPP) in New Mexico. After less than two years, Hanford will have a program certified by the Carlsbad Area Office (CAO). By picking a simple waste stream, taking advantage of lessons learned at the other sites, as well as communicating effectively with the CAO, Hanford was able to achieve certification in record time. This effort was further simplified by having a centralized program centered on the Waste Receiving and Processing (WRAP) Facility that contains most of the equipment required to characterize TRU waste. The use of fixed facilities for the characterization of TRU waste at sites with a long-term clean-up mission can be cost effective for several reasons. These include the ability to control the environment in which sensitive instrumentation is required to operate and ensuring that calibrations and maintenance activities are scheduled and performed as an operating routine. Other factors contributing to cost effectiveness include providing approved procedures and facilities for handling hazardous materials and anticipated contingencies and performing essential evolutions, and regulating and smoothing the work load and environmental conditions to provide maximal efficiency and productivity. Another advantage is the ability to efficiently provide characterization services to other sites in the Department of Energy (DOE) Complex that do not have the same capabilities. The Waste Receiving and Processing (WRAP) Facility is a state-of-the-art facility designed to consolidate the operations necessary to inspect, process and ship waste to facilitate verification of contents for certification to established waste acceptance criteria. The WRAP facility inspects, characterizes, treats, and certifies transuranic (TRU), low-level and mixed waste at the Hanford Site in Washington state. Fluor Hanford operates the $89

Application of a canine ²³⁸Pu dosimetry model to human bioassay data

Energy Technology Data Exchange (ETDEWEB)

Hickman, Jr., A. W. [Florida Univ., Gainesville, FL (United States)

1991-08-01

Associated with the use of 2²³⁸Pu in thermoelectric power sources for space probes and power supplies for cardiac devices is the potential for human exposure to ²³⁸Pu, primarily by inhalation. In the event of human internal exposure, a means is needed for assessing the level of intake and calculating radiation doses. Several bioassay/dosimetry models have been developed for ²³⁹Pu. However, results from studies with laboratory animals have indicated that the biokinetics, and therefore the descriptive models, of ²³⁸Pu are significantly different from those for ²³⁹Pu. A canine model accounting for these differences has been applied in this work to urinary excretion data from seven humans occupationally exposed to low levels of an insoluble ²³⁸Pu compound. The modified model provides a good description of the urinary excretion kinetics observed in the exposed humans. The modified model was also used to provide estimates of the initial intakes of ²³⁸Pu for the seven individuals; these estimates ranged from 4.5 nCi (170 Bq) to 87 nCi (3200 Bq). Autopsy data on the amount and distribution of ²³⁸Pu retained in the organs may be used in the future to validate or refute both these estimates and the assumptions used to formulate the human model. Modification of the human model to simulate an injection exposure to ²³⁹Pu gave patterns of retention in the organs and urinary excretion comparable to those seen previously in humans; further modification of the model using fecal data (unavailable for the subjects of this study) is indicated.

Los Alamos Plutonium Facility newly generated TRU waste certification

International Nuclear Information System (INIS)

Gruetzmacher, K.; Montoya, A.; Sinkule, B.; Maez, M.

1997-01-01

This paper presents an overview of the activities being planned and implemented to certify newly generated contact handled transuranic (TRU) waste produced by Los Alamos National Laboratory's (LANL's) Plutonium Facility. Certifying waste at the point of generation is the most important cost and labor saving step in the WIPP certification process. The pedigree of a waste item is best known by the originator of the waste and frees a site from expensive characterization activities such as those associated with legacy waste. Through a cooperative agreement with LANLs Waste Management Facility and under the umbrella of LANLs WIPP-related certification and quality assurance documents, the Plutonium Facility will be certifying its own newly generated waste. Some of the challenges faced by the Plutonium Facility in preparing to certify TRU waste include the modification and addition of procedures to meet WIPP requirements, standardizing packaging for TRU waste, collecting processing documentation from operations which produce TRU waste, and developing ways to modify waste streams which are not certifiable in their present form

Radionuclide concentrations in vegetation at radioactive-waste disposal Area G during the 1994 growing season

International Nuclear Information System (INIS)

Fresquez, P.R.; Biggs, J.B.; Bennett, K.D.

1995-01-01

Overstory (pinon pine) and understory (grass and forb) vegetation samples were collected within and around selected points at Area G-a low-level radioactive solid-waste disposal facility at Los Alamos National Laboratory-for the analysis of tritium ( 3 H), strontium ( 90 Sr), plutonium ( 238 Pu and 239 Pu), cesium ( 137 Cs), americium ( 241 Am), and total uranium. In general, most vegetation samples collected within and around Area G contained radionuclide levels in higher concentrations than vegetation collected from background areas. Tritium, in particular, was detected as high as 5,800 pCi/mL in overstory vegetation collected outside the fence just west of the tritium shafts; this suggests that tritium is migrating from this waste repository through subsurface pathways. Also, understory vegetation collected north of the transuranic (TRU) pads (outside the fence of Area G) contained the highest values of 90 Sr, 238 Pu, 239 Pu, 137 Cs, and 241 Am, and may be a result of surface holding, storage, or disposal activities

Determination of plutonium isotopes (238Pu, 239Pu, 240Pu, 241Pu) in environmental samples using radiochemical separation combined with radiometric and mass spectrometric measurements.

Science.gov (United States)

Xu, Yihong; Qiao, Jixin; Hou, Xiaolin; Pan, Shaoming; Roos, Per

2014-02-01

This paper reports an analytical method for the determination of plutonium isotopes ((238)Pu, (239)Pu, (240)Pu, (241)Pu) in environmental samples using anion exchange chromatography in combination with extraction chromatography for chemical separation of Pu. Both radiometric methods (liquid scintillation counting and alpha spectrometry) and inductively coupled plasma mass spectrometry (ICP-MS) were applied for the measurement of plutonium isotopes. The decontamination factors for uranium were significantly improved up to 7.5 × 10(5) for 20 g soil compared to the level reported in the literature, this is critical for the measurement of plutonium isotopes using mass spectrometric technique. Although the chemical yield of Pu in the entire procedure is about 55%, the analytical results of IAEA soil 6 and IAEA-367 in this work are in a good agreement with the values reported in the literature or reference values, revealing that the developed method for plutonium determination in environmental samples is reliable. The measurement results of (239+240)Pu by alpha spectrometry agreed very well with the sum of (239)Pu and (240)Pu measured by ICP-MS. ICP-MS can not only measure (239)Pu and (240)Pu separately but also (241)Pu. However, it is impossible to measure (238)Pu using ICP-MS in environmental samples even a decontamination factor as high as 10(6) for uranium was obtained by chemical separation. © 2013 Elsevier B.V. All rights reserved.

/sup 238/Pu fuel-form processes. Quarterly report, October-December 1981

Energy Technology Data Exchange (ETDEWEB)

1982-05-01

Progress in the Savannah River /sup 238/Pu Fuel Form Program is summarized. Work during this period concentrated on the extensive cracking of the /sup 238/PuO/sub 2/ fuel form prior to encapsulation in the iridium containment shell for heat sources. This cracking results in increased recycle cost and decreased production efficiency. To better understand this cracking, Savannah River Laboratory (SRL) has made an extensive review of the development of /sup 238/PuO/sub 2/ fuel forms from small-scale Multi-hundred Watt (MHW) pellets through the current GPHS full-scale pellet production. Historically, /sup 238/PuO/sub 2/ fuel has almost always been uncracked after hot pressing in a graphite die, but has emerged cracked and fragile from the final heat-treatment furnace. The cracking tendency depends on the microstructure of the fuel form and on the hot pressing conditions used to fabricate it. In general, a microstructure of large intershard porosity is more desirable because it allows internal gas to escape more readily and it can absorb more reoxidation strain. Studies of the GPHS microstructure showed that the internal structures of typical GPHS Pellets fabricated at LANL and in the PEF differed significantly. The LANL pellets had severe density gradients and were extensively cracked.

Spatial and temporal variations of plutonium isotopes (238Pu and 239,240Pu) in sediments off the Rhone River mouth (NW Mediterranean)

International Nuclear Information System (INIS)

Lansard, B.; Charmasson, S.; Gasco, C.; Anton, M.P.; Grenz, C.; Arnaud, M.

2007-01-01

The dispersion and fate of the Rhone River inputs to the Gulf of Lions (Northwestern Mediterranean Sea) have been studied through the spatial and temporal distributions of plutonium isotopes in continental shelf sediments. Plutonium isotopes ( 238 Pu and 239,240 Pu) are appropriate tracers to follow the dispersion of particulate matter due both to their high affinity for particles and their long half-lives. In the Rhone River valley, plutonium isotopes originate from both the weathering of the catchment basin contaminated by global atmospheric fallout, and the liquid effluents released from the Marcoule reprocessing plant since 1961. This work presents a first detailed study on 238 Pu and 239,240 Pu distributions in sediments from the Rhone prodelta to the adjacent continental shelf, since the decommissioning of Marcoule in 1997. The vertical distribution of Pu isotopes has been analysed in a 4.75 m long core sampled in 2001 at the Rhone mouth. Despite this length, plutonium is found at the last 10 cm, manifesting the high sedimentation rate of the prodeltaic area and its ability for trapping fine-grained sediments and associated contaminants. The highest 238 Pu and 239,240 Pu concentrations reached 1.26 and 5.97 Bq kg -1 respectively and were found within the layer 280-290 cm. The 238 Pu/ 239,240 Pu activity ratios (AR) demonstrated an efficient and huge trapping of the Pu isotopes derived from Marcoule. The fresh sediments, located on the top of the core, show lower plutonium activity concentrations and lower 238 Pu/ 239,240 Pu ratios. This decrease is in close relation with the shut down of the Marcoule reprocessing plant in 1997. In 2001, plutonium isotopes were also analysed in 21 surface sediments located offshore and concentrations ranged from 0.03 to 0.17 Bq kg -1 for 238 Pu and from 0.33 to 1.72 Bq kg -1 for 239,240 Pu. The 238 Pu/ 239,240 Pu AR ranged from 0.24 close to the river mouth to 0.06 southwards, indicating the decreasing influence of the

TRU waste-assay instrumentation and application in nuclear-facility decommissioning

International Nuclear Information System (INIS)

Umbarger, C.J.

1982-01-01

The Los Alamos TRU waste assay program is developing measurement techniques for TRU and other radioactive waste materials generated by the nuclear industry, including decommissioning programs. Systems are now being fielded for test and evaluation purposes at DOE TRU waste generators. The transfer of this technology to other facilities and the commercial instrumentation sector is well in progress. 6 figures

Irradiation of blood by 238Pu alpha particles

International Nuclear Information System (INIS)

Hungate, F.P.; Riemath, W.F.; Culver, G.G.; Gillis, M.F.; Ragan, H.A.

1976-01-01

A developmental 238 Pu blood irradiator produced no evidence of lymphopenia in a dog. Irradiation continued for a year at an estimated rate of about 100 rads/day, but this dosimetry is highly uncertain

Major Components of the National TRU Waste System Optimization Project

International Nuclear Information System (INIS)

Moody, D.C.; Bennington, B.; Sharif, F.

2002-01-01

The National Transuranic (TRU) Program (NTP) is being optimized to allow for disposing of the legacy TRU waste at least 10 years earlier than originally planned. This acceleration will save the nation an estimated $713. The Department of Energy's (DOE'S) Carlsbad Field Office (CBFO) has initiated the National TRU Waste System Optimization Project to propose, and upon approvaI, implement activities that produce significant cost saving by improving efficiency, thereby accelerating the rate of TRU waste disposal without compromising safety. In its role as NTP agent of change, the National TRU Waste System Optimization Project (the Project) (1) interacts closely with all NTP activities. Three of the major components of the Project are the Central Characterization Project (CCP), the Central Confirmation Facility (CCF), and the MobiIe/Modular Deployment Program.

Los Alamos National Laboratory TRU waste sampling projects

International Nuclear Information System (INIS)

Yeamans, D.; Rogers, P.; Mroz, E.

1997-01-01

The Los Alamos National Laboratory (LANL) has begun characterizing transuranic (TRU) waste in order to comply with New Mexico regulations, and to prepare the waste for shipment and disposal at the Waste Isolation Pilot Plant (WIPP), near Carlsbad, New Mexico. Sampling consists of removing some head space gas from each drum, removing a core from a few drums of each homogeneous waste stream, and visually characterizing a few drums from each heterogeneous waste stream. The gases are analyzed by GC/MS, and the cores are analyzed for VOC's and SVOC's by GC/MS and for metals by AA or AE spectroscopy. The sampling and examination projects are conducted in accordance with the ''DOE TRU Waste Quality Assurance Program Plan'' (QAPP) and the ''LANL TRU Waste Quality Assurance Project Plan,'' (QAPjP), guaranteeing that the data meet the needs of both the Carlsbad Area Office (CAO) of DOE and the ''WIPP Waste Acceptance Criteria, Rev. 5,'' (WAC)

Hematological responses after inhaling {sup 238}PuO{sub 2}: An extrapolation from beagle dogs to humans

Energy Technology Data Exchange (ETDEWEB)

Scott, B.R.; Muggenburg, B.A.; Welsh, C.A.; Angerstein, D.A.

1994-11-01

The alpha emitter plutonium-238 ({sup 238}Pu), which is produced in uranium-fueled, light-water reactors, is used as a thermoelectric power source for space applications. Inhalation of a mixed oxide form of Pu is the most likely mode of exposure of workers and the general public. Occupational exposures to {sup 238}PuO{sub 2} have occurred in association with the fabrication of radioisotope thermoelectric generators. Organs and tissue at risk for deterministic and stochastic effects of {sup 238}Pu-alpha irradiation include the lung, liver, skeleton, and lymphatic tissue. Little has been reported about the effects of inhaled {sup 238}PuO{sub 2} on peripheral blood cell counts in humans. The purpose of this study was to investigate hematological responses after a single inhalation exposure of Beagle dogs to alpha-emitting {sup 238}PuO{sub 2} particles and to extrapolate results to humans.

Demonstration of remotely operated TRU waste size reduction and material handling equipment

International Nuclear Information System (INIS)

Looper, M.G.; Charlesworth, D.L.

1988-01-01

The Savannah River Laboratory (SRL) is developing remote size reduction and material handling equipment to prepare 238 Pu contaminated waste for permanent disposal at the Waste Isolation Pilot Plant (WIPP) in New Mexico. The waste is generated at the Savannah River Plant (SRP) from normal operation and decommissioning activity and is retrievably stored onsite. A Transuranic Waste Facility for preparing, size-reducing, and packaging this waste for disposal is scheduled for completion in 1995. A cold test facility for demonstrating the size reduction and material handling equipment was built, and testing began in January 1987. 9 figs., 1 tab

Characterization of 618-11 solid waste burial ground, disposed waste, and description of the waste generating facilities

International Nuclear Information System (INIS)

Hladek, K.L.

1997-01-01

The 618-11 (Wye or 318-11) burial ground received transuranic (TRTJ) and mixed fission solid waste from March 9, 1962, through October 2, 1962. It was then closed for 11 months so additional burial facilities could be added. The burial ground was reopened on September 16, 1963, and continued operating until it was closed permanently on December 31, 1967. The burial ground received wastes from all of the 300 Area radioactive material handling facilities. The purpose of this document is to characterize the 618-11 solid waste burial ground by describing the site, burial practices, the disposed wastes, and the waste generating facilities. This document provides information showing that kilogram quantities of plutonium were disposed to the drum storage units and caissons, making them transuranic (TRU). Also, kilogram quantities of plutonium and other TRU wastes were disposed to the three trenches, which were previously thought to contain non-TRU wastes. The site burial facilities (trenches, caissons, and drum storage units) should be classified as TRU and the site plutonium inventory maintained at five kilograms. Other fissile wastes were also disposed to the site. Additionally, thousands of curies of mixed fission products were also disposed to the trenches, caissons, and drum storage units. Most of the fission products have decayed over several half-lives, and are at more tolerable levels. Of greater concern, because of their release potential, are TRU radionuclides, Pu-238, Pu-240, and Np-237. TRU radionuclides also included slightly enriched 0.95 and 1.25% U-231 from N-Reactor fuel, which add to the fissile content. The 618-11 burial ground is located approximately 100 meters due west of Washington Nuclear Plant No. 2. The burial ground consists of three trenches, approximately 900 feet long, 25 feet deep, and 50 feet wide, running east-west. The trenches constitute 75% of the site area. There are 50 drum storage units (five 55-gallon steel drums welded together

Characterization of 618-11 solid waste burial ground, disposed waste, and description of the waste generating facilities

Energy Technology Data Exchange (ETDEWEB)

Hladek, K.L.

1997-10-07

The 618-11 (Wye or 318-11) burial ground received transuranic (TRTJ) and mixed fission solid waste from March 9, 1962, through October 2, 1962. It was then closed for 11 months so additional burial facilities could be added. The burial ground was reopened on September 16, 1963, and continued operating until it was closed permanently on December 31, 1967. The burial ground received wastes from all of the 300 Area radioactive material handling facilities. The purpose of this document is to characterize the 618-11 solid waste burial ground by describing the site, burial practices, the disposed wastes, and the waste generating facilities. This document provides information showing that kilogram quantities of plutonium were disposed to the drum storage units and caissons, making them transuranic (TRU). Also, kilogram quantities of plutonium and other TRU wastes were disposed to the three trenches, which were previously thought to contain non-TRU wastes. The site burial facilities (trenches, caissons, and drum storage units) should be classified as TRU and the site plutonium inventory maintained at five kilograms. Other fissile wastes were also disposed to the site. Additionally, thousands of curies of mixed fission products were also disposed to the trenches, caissons, and drum storage units. Most of the fission products have decayed over several half-lives, and are at more tolerable levels. Of greater concern, because of their release potential, are TRU radionuclides, Pu-238, Pu-240, and Np-237. TRU radionuclides also included slightly enriched 0.95 and 1.25% U-231 from N-Reactor fuel, which add to the fissile content. The 618-11 burial ground is located approximately 100 meters due west of Washington Nuclear Plant No. 2. The burial ground consists of three trenches, approximately 900 feet long, 25 feet deep, and 50 feet wide, running east-west. The trenches constitute 75% of the site area. There are 50 drum storage units (five 55-gallon steel drums welded together

The toxicity of inhaled particles of 238PuO2 in dogs

International Nuclear Information System (INIS)

Muggenburg, B.A.; Guilmette, R.A.; Griffith, W.C. Jr.; Hahn, F.F.; Boecker, B.B.

1991-01-01

This study was conducted to determine the toxicity of inhaled 238 PuO 2 in the dog. Inhalation was selected because it is the mostly likely route of human exposure in the event of an accidental airborne release. Of 166 dog in the study, 72 inhaled 1.5μm and 72 inhaled 3.0 μm activity median aerodynamic diameter particles of 238 PuO 2 . Another 24 dogs inhaled the aerosol vector without plutonium. The aerosol exposures resulted in initial pulmonary burdens ranging from 37 to 0.11 and 55.5 to 0.37 kBq of 238 Pu/kg body mass, of 1.5 μm and 3.0 μ, particles, respectively. The particles dissolved slowly resulting in translocation of the Pu to liver, bone and other sites. The dogs were observed for biological effects over their life span. Necropsies were performed at death, and tissues were examined microscopically. The principal late-occurring effects were tumors of the lung, skeleton, and liver. Risk factors estimated for these cancers were 2800 lung cancers/10 4 Gy, 800 liver cancers/10 4 Gy, and 6200 bone cancers/10 4 Gy for dogs. The potential hazard from 238 Pu to humans may include tumors of the lung, bone and liver because of the likelihood of similarity of the dose patterns for the two species. 10 refs., 1 fig., 3 tabs

Repackaging of High Fissile TRU Waste at the Transuranic Waste Processing Center - 13240

Energy Technology Data Exchange (ETDEWEB)

Oakley, Brian; Heacker, Fred [WAI, TRU Waste Processing Center, 100 WIPP Road Lenoir City, TN 37771 (United States); McMillan, Bill [DOE, Oak Ridge Operations, Bldg. 2714, Oak Ridge, TN 37830 (United States)

2013-07-01

Twenty-six drums of high fissile transuranic (TRU) waste from Oak Ridge National Laboratory (ORNL) operations were declared waste in the mid-1980's and placed in storage with the legacy TRU waste inventory for future treatment and disposal at the Waste Isolation Pilot Plant (WIPP). Repackaging and treatment of the waste at the TRU Waste Packaging Center (TWPC) will require the installation of additional equipment and capabilities to address the hazards for handling and repackaging the waste compared to typical Contact Handled (CH) TRU waste that is processed at the TWPC, including potential hydrogen accumulation in legacy 6M/2R packaging configurations, potential presence of reactive plutonium hydrides, and significant low energy gamma radiation dose rates. All of the waste is anticipated to be repackaged at the TWPC and certified for disposal at WIPP. The waste is currently packaged in multiple layers of containers which presents additional challenges for repackaging activities due to the potential for the accumulation of hydrogen gas in the container headspace in quantities than could exceed the Lower Flammability Limit (LFL). The outer container for each waste package is a stainless steel 0.21 m{sup 3} (55-gal) drum which contains either a 0.04 m{sup 3} or 0.06 m{sup 3} (10-gal or 15-gal) 6M drum. The inner 2R container in each 6M drum is ∼12 cm (5 in) outside diameter x 30-36 cm (12-14 in) long and is considered to be a > 4 liter sealed container relative to TRU waste packaging criteria. Inside the 2R containers are multiple configurations of food pack cans, pipe nipples, and welded capsules. The waste contains significant quantities of high burn-up plutonium oxides and metals with a heavy weight percentage of higher atomic mass isotopes and the subsequent in-growth of significant quantities of americium. Significant low energy gamma radiation is expected to be present due to the americium in-growth. Radiation dose rates on inner containers are estimated

Waste Isolation Pilot Plant RH TRU waste preoperational checkout: Final report

International Nuclear Information System (INIS)

1988-06-01

This report documents the results of the Waste Isolation Pilot Plant (WIPP) Remote-Handled Transuranic (RH TRU) Waste Preoperational Checkout. The primary objective of this checkout was to demonstrate the process of handling RH TRU waste packages, from receipt through emplacement underground, using equipment, personnel, procedures, and methods to be used with actual waste packages. A further objective was to measure operational time lines to provide bases for confirming the WIPP design through put capability and for projecting operator radiation doses. Successful completion of this checkout is a prerequisite to the receipt of actual RH TRU waste. This checkout was witnessed in part by members of the Environmental Evaluation Group (EEG) of the state of New Mexico. Further, this report satisfies a key milestone contained in the Agreement for Consultation and Cooperation with the state of New Mexico. 4 refs., 26 figs., 4 tabs

Assessment of 238Pu and 239+240Pu, in marine sediments of the oceans Atlantic and Pacific of Guatemala

International Nuclear Information System (INIS)

Mendez Ochaita, L.

2000-01-01

In this investigation samples of marine sediments were taken from 14 places representatives of the oceans coast of Guatemala. For the assesment of 238 Pu and 239+240 Pu in sediments a radiochemical method was used to mineralize sediments and by ionic interchange it was separated from other elements, after that an electrodeposition of plutonium was made in metallic discs. The radioactivity of plutonium was measured by alpha spectrometry system and the alpha spectrums were obtained. The levels of plutonium are not higher than other countries that shown contamination. The contamination of isotope of 239+240 Pu is higher than 238 Pu and the contamination by two isotopes of plutonium is higher in the Atlantic than the Pacific ocean

Remote Handled TRU Waste Status and Activities and Challenges at the Hanford Site

International Nuclear Information System (INIS)

MCKENNEY, D.E.

2000-01-01

A significant portion of the Department of Energy's forecast volume of remote-handled (RH) transuranic (TRU) waste will originate from the Hanford Site. The forecasted Hanford RH-TRU waste volume of over 2000 cubic meters may constitute over one-third of the forecast inventory of RH-TRU destined for disposal at the Waste Isolation Pilot Plant (WIPP). To date, the Hanford TRU waste program has focused on the retrieval, treatment and certification of the contact-handled transuranic (CH-TRU) wastes. This near-term focus on CH-TRU is consistent with the National TRU Program plans and capabilities. The first shipment of CH-TRU waste from Hanford to the WIPP is scheduled early in Calendar Year 2000. Shipments of RH-TRU from Hanford to the WIPP are scheduled to begin in Fiscal Year 2006 per the National TRU Waste Management Plan. This schedule has been incorporated into milestones within the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement). These Tri-Party milestones (designated the ''M-91'' series of milestones) relate to development of project management plans, completion of design efforts, construction and contracting schedules, and initiation of process operations. The milestone allows for modification of an existing facility, construction of a new facility, and/or commercial contracting to provide the capabilities for processing and certification of RH-TRU wastes for disposal at the WIPP. The development of a Project Management Plan (PMP) for TRU waste is the first significant step in the development of a program for disposal of Hanford's RH-TRU waste. This PMP will address the path forward for disposition of waste streams that cannot be prepared for disposal in the Hanford Waste Receiving and Processing facility (a contact-handled, small container facility) or other Site facilities. The PMP development effort has been initiated, and the PMP will be provided to the regulators for their approval by June 30, 2000. This plan will detail the

Fabrication of gamma sources using the neutron-gamma reactions of 238Pu13C

International Nuclear Information System (INIS)

Solinhac, I.; Maillard, C.; Donnet, L.

2004-01-01

A production campaign for 238 Pu 13 C sources with gamma fluence ranging from 2500 to 4500 gamma/s/4π at 6.13 MeV was carried out in 2002 in Atalante. An experimental study was undertaken to prepare the 238 PuC mixture, which is the most delicate step. This procedure is described together with the other steps in the source fabrication process: purification of a plutonium oxide batch, preparation of a nitric solution of 238 Pu, measurement of the gamma fluence of the PuC mixture before and after insertion into each of the two stainless steel capsules that constitute a PuN 2 O package, welding of the second envelope followed by leak testing, final measurement of the gamma fluence of the sealed source. This PuC sources fabrication procedure is effective: all the sources include the required gamma activity with an uncertainty on the gamma fluence of less than 10%. (authors)

TRU assay system and measurements

International Nuclear Information System (INIS)

Brodzinski, R.L.

1984-02-01

The measurement of the transuranic content of nuclear products or process residues has become increasingly important for the recovery of fissionable material from spent fuel elements, the identification of commercial fuel elements which have not yet reached full burnup, the measurement and recovery of transuranics from discarded or stored waste materials, the determination of the transuranic content in high gamma activity waste material scheduled for disposal, compliance with 10CFR61 by land burial operators/shippers, and the satisfaction of accountability requirements. Active neutron interrogation techniques measure either the prompt neutrons or the beta delayed neutrons from fission products following induced fission. These techniques normally only measure fissile transuranics ( 235 U, 239 Pu, and 241 Pu) and are commonly applied only to contact handleable waste. Passive neutron interrogation techniques, on the other hand, are capable of measuring all transuranics except 235 U with adequate sensitivity and will work on both contact handleable and high gamma activity wastes. Since the passive techniques are senstitive to a wider spectrum of transuranic isotopes than the active techniques, substantially less complex and less expensive than the active systems, and they have proven techniques for measuring small quantities of TRU in high gamma activity packages, the passive neutron TRU assay technology was chosen for development into the instruments discussed in this paper

Vitrification of TRU wastes at Rocky Flats Plant

International Nuclear Information System (INIS)

Williams, P.M.; Johnson, A.J.; Ledford, J.A.

1979-01-01

Immobilization of incinerator ash and various noncombustible TRU wastes was investigated. In three different research projects borosilicate glass proved to be the best candidate for TRU waste fixation. This glass has excellent chemical durability, long-term stability in the presence of radiation, and will withstand continuous temperatures up to 400 0 C without devitrification. In addition, wastes prepared in the form of glass will attain densities of approximately 2500 kg/m 3 (2.5 g/cc). The free forming method of producing glass buttons provides a very simple, consistent, low maintenance way of producing a final waste form for transporting and either retrievable or permanent storage for TRU waste. The vitrification process produces a durable glass from the low density ash generated by the fluidized bed incinerator process and provides volume and weight reductions that are superior to other fixation processes. This results in decreased transportation and storage costs

CH-TRU Waste Content Codes

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2008-01-16

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

Data Evaluation of Actinide Cross Sections: ²³⁸Pu, ²³⁷Pu, and ²³⁶Pu

Energy Technology Data Exchange (ETDEWEB)

Guaglioni, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jurgenson, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Descalle, M. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Thompson, I. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ormand, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Escher, J. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Younes, W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mattoon, C. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Beck, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Burke, J. T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bailey, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-10-04

This report documents the recent evaluation of the ²³⁶Pu, ²³⁷Pu, and ²³⁸Pu cross section sets. Nuclear data evaluation is the fundamental interface that takes measured nuclear cross section data and turns them into a continuous curve that 1) is consistent with other measurements and nuclear reaction theory/models, and 2) is required by down-stream users. All experiments that generate nuclear data need to include an evaluation step for their data to be broadly useful to the end users.

Behavior of nuclides at plasma melting of TRU wastes

International Nuclear Information System (INIS)

Amakawa, Tadashi; Adachi, Kazuo

2001-01-01

Arc plasma heating technique can easily be formed at super high temperature, and can carry out stable heating without any effect of physical and chemical properties of the wastes. By focussing to these characteristics, this technique was experimentally investigated on behavior of TRU nuclides when applying TRU wastes forming from reprocessing process of used fuels to melting treatment by using a mimic non-radioactive nuclide. At first, according to mechanism determining the behavior of TRU nuclides, an element (mimic nuclide) to estimate the behavior was selected. And then, to zircaloy with high melting point or steel can simulated to metal and noncombustible wastes and fly ash, the mimic nuclide was added, prior to melting by using the arc plasma heating technique. As a result, on a case of either melting sample, it was elucidated that the nuclides hardly moved into their dusts. Then, the technique seems to be applicable for melting treatment of the TRU wastes. (G.K.)

Solidification of TRU wastes in a ceramic matrix

International Nuclear Information System (INIS)

Loida, A.; Schubert, G.

1991-01-01

Aluminumsilicate based ceramic materials have been evaluated as an alternative waste form for the incorporation of TRU wastes. These waste forms are free of water and - cannot generate hydrogen radiolyticly, - they show good compatibility between the compounds of the waste and the matrix, - they are resistent against aqueous solutions, heat and radiation. R and D-work has been performed to demonstrate the suitability of this waste form for the immobilization of TRU-wastes. Four kinds of original TRU-waste streams and a mixture of all of them have been immobilized by ceramization, using glove box and remote operation technique as well. Clay minerals, (kaolinite, bentonite) and reactive corundum were selected as ceramic raw materials (KAB 78) in an appropriate ratio yielding 78 wt% Al 2 O 3 and 22 wt%SiO 2 . The main process steps are (i) pretreatment of the liquid waste (concentration, denitration, neutralization, solid- liquid separation), (ii) mixing with ceramic raw materials and forming, (iii) heat treatment with T max. of 1300 0 C for 15 minutes. The waste load of the ceramic matrix has been increased gradually from 20 to 50, in some cases to 60 wt.%

Comparative assessment of disposal of TRU waste in a greater-confinement disposal facility

International Nuclear Information System (INIS)

Cohn, J.J.; Smith, C.F.; Ciminesi, F.J.; Dickman, P.T.; O'Neal, D.A.

1982-11-01

This study reviewed previous work that established generic limits for shallow land burial of TRU contaminated wastes and extended previous methodology to estimate approximate appropriate burial limits for TRU wastes in an arid zone greater confinement disposal facility (GCDF). An erosion scenario provided the limiting pathway in the previous determination of generic shallow land burial limits. Erosion removed the cover soil, exposing the waste mass to habitation and agriculture. For the deep burial concept (that is, burial at a depth greater than 10 m [33 ft]), the aquifer transport scenario was controlling. In both cases, the assumed site conditions were characteristic of a humid zone in which groundwater flows immediately below the waste deposit. In deriving limits for an arid site GCDF, either the erosion/reclaimer or the aquifer transport scenario could provide the controlling pathway, depending on the nuclide and the assumed burial depth. The derived limits were higher for the arid sited GCDF than those of the generic humid study. The physical processes that increase limits relative to the generic study include increased time during which radioactive decay occurs prior to release and increased dilution. Some nuclides were effectively unlimited in an arid zone GCDF, while others (notably Pu-239) were affected on a much smaller scale, primarily due to very long half-lives. As a final comment, the limit values derived in this report represent adjustments to the calculations of the Healy and Rodgers report (LA-UR-79-100). Those original calculations were very conservative, utilizing a worst case approach, but nevertheless involving significant levels of uncertainty in key assumptions. Consequently, the results are assumption dependent. Other approaches to such an analysis could, and should be used to develop site specific concentration limits for TRU wastes

Pu-238 Supply Program Project Execution Plan

International Nuclear Information System (INIS)

Wham, Robert M.; Martin, Sherman

2012-01-01

This Pu-238 Supply Program Project Execution Plan (PEP) summarizes critical information and processes necessary to manage the program. The PEP is the primary agreement regarding planning and objectives between The Department of Energy Office of Nuclear Energy (DOE NE-75), Oak Ridge National Laboratory Site Office (OSO) and the Oak Ridge National Laboratory (ORNL). The acquisition executive (AE) will approve the PEP. The PEP is a living document that will be reviewed and revised periodically until the project is complete. The purpose of the project is to reestablish the capability to produce plutonium-238 (Pu-238) domestically. This capability consists primarily of procedures, processes, and design information, not capital assets. As such, the project is not subject to the requirements of DOE O 413.3B, but it will be managed using the project management principles and best practices defined there. It is likely that some capital asset will need to be acquired to complete tasks within the project. As these are identified, project controls and related processes will be updated as necessary. Because the project at its initiation was envisioned to require significant capital assets, Critical Decision 0 (CD-0) was conducted in accordance with DOE O 413.3B, and the mission need was approved on December 9, 2003, by William Magwood IV, director of the Office of Nuclear Energy (NE), Science and Technology, DOE. No date was provided for project start-up at that time. This PEP is consistent with the strategy described in the June 2010 report to Congress, Start-up Plan for Plutonium-238 Production for Radioisotope Power Systems.

Changes in plant availability of Pu-238 during a nine year experimental period

International Nuclear Information System (INIS)

Eriksson, Aa.

1985-01-01

A short description is given of the changes observed in the plant availability of Pu-238 in eight soils during a nine year experimental period. It was found that during the first four-year period with clover as test crop, the plant uptake of Pu-238 was reduced with availability half lives ranging from 0.8 to 2.0 years. The reduction rate seemed proportional to the initial uptake levels, except for lime rich clay soils, where the reduction rate was high regardless of the uptake level. In 1980 when the test crop clover was replaced by spring wheat, the necessary soil management operations caused intenser aeration and drying in one block of the replicates. As a consequence, the Pu-uptake in that block became considerably higher than in the others. This event can be interpreted as an indirect evidence for the reversibility of that process in soil, which has caused the reduced plant availability of Pu-238

A study for the safety evaluation of geological disposal of TRU waste and influence on disposal site design by change of amount of TRU waste (Joint research)

International Nuclear Information System (INIS)

Hasegawa, Makoto; Kondo, Hitoshi; Takahashi, Kuniaki; Funabashi, Hideaki; Kawatsuma, Shinji; Kamei, Gento; Hirano, Fumio; Mihara, Morihiro; Ueda, Hiroyoshi; Ohi, Takao; Hyodo, Hideaki

2011-02-01

In the safety evaluation of the geological disposal of the TRU waste, it is extremely important to share the information with the Research and development organization (JAEA: that is also the waste generator) by the waste disposal entrepreneur (NUMO). In 2009, NUMO and JAEA set up a technical commission to investigate the reasonable TRU waste disposal following a cooperation agreement between these two organizations. In this report, the calculation result of radionuclide transport for a TRU waste geological disposal system was described, by using the Tiger code and the GoldSim code at identical terms. Tiger code is developed to calculate a more realistic performance assessment by JAEA. On the other hand, GoldSim code is the general simulation software that is used for the computation modeling of NUMO TRU disposal site. Comparing the calculation result, a big difference was not seen. Therefore, the reliability of both codes was able to be confirmed. Moreover, the influence on the disposal site design (Capacity: 19,000m 3 ) was examined when 10% of the amount of TRU waste increased. As a result, it was confirmed that the influence of the site design was very little based on the concept of the Second Progress Report on Research and Development for TRU Waste Disposal in Japan. (author)

A strategy for analysis of TRU waste characterization needs

International Nuclear Information System (INIS)

Leigh, C.D.; Chu, M.S.Y.; Arvizu, J.S.; Marcinkiewicz, C.J.

1994-01-01

Regulatory compliance and effective management of the nation's TRU waste requires knowledge about the constituents present in the waste. With limited resources, the DOE needs a cost-effective characterization program. In addition, the DOE needs a method for predicting the present and future analytical requirements for waste characterization. Thus, a strategy for predicting the present and future waste characterization needs that uses current knowledge of the TRU inventory and prioritization of the data needs is presented

High resolution gamma-ray spectrometry of culverts containing transuranic waste at the Savannah River Site

International Nuclear Information System (INIS)

Hofstetter, K.J.; Sigg, R.

1990-01-01

A number of concrete culverts used to retrievably store drummed, dry, radioactive waste at the Savannah River Site (SRS), were suspected of containing ambiguous quantities of transuranic (TRU) nuclides. These culverts were assayed in place for Pu-239 content using thermal and fast neutron counting techniques. High resolution gamma-ray spectroscopy on 17 culverts, having neutron emission rates several times higher than expected, showed characteristic gamma-ray signatures of neutron emitters other than Pu-239 (e.g., Pu-238, Pu/Be, or Am/Be neutron sources). This study confirmed the Pu-239 content of the culverts with anomalous neutron rates and established limits on the Pu-239 mass in each of the 17 suspect culverts by in-field, non-intrusive gamma-ray measurements

Characterizing cemented TRU waste for RCRA hazardous constituents

International Nuclear Information System (INIS)

Yeamans, D.R.; Betts, S.E.; Bodenstein, S.A.

1996-01-01

Los Alamos National Laboratory (LANL) has characterized drums of solidified transuranic (TRU) waste from four major waste streams. The data will help the State of New Mexico determine whether or not to issue a no-migration variance of the Waste Isolation Pilot Plant (WIPP) so that WIPP can receive and dispose of waste. The need to characterize TRU waste stored at LANL is driven by two additional factors: (1) the LANL RCRA Waste Analysis Plan for EPA compliant safe storage of hazardous waste; (2) the WIPP Waste Acceptance Criteria (WAC) The LANL characterization program includes headspace gas analysis, radioassay and radiography for all drums and solids sampling on a random selection of drums from each waste stream. Data are presented showing that the only identified non-metal RCRA hazardous component of the waste is methanol

Waste Isolation Pilot Plant simulated RH TRU waste experiments: Data and interpretation pilot

International Nuclear Information System (INIS)

Molecke, M.A.; Argueello, G.J.; Beraun, R.

1993-04-01

The simulated, i.e., nonradioactive remote-handled transuranic waste (RH TRU) experiments being conducted underground in the Waste Isolation Pilot Plant (WIPP) were emplaced in mid-1986 and have been in heated test operation since 9/23/86. These experiments involve the in situ, waste package performance testing of eight full-size, reference RH TRU containers emplaced in horizontal, unlined test holes in the rock salt ribs (walls) of WIPP Room T. All of the test containers have internal electrical heaters; four of the test emplacements were filled with bentonite and silica sand backfill materials. We designed test conditions to be ''near-reference'' with respect to anticipated thermal outputs of RH TRU canisters and their geometrical spacing or layout in WIPP repository rooms, with RH TRU waste reference conditions current as of the start date of this test program. We also conducted some thermal overtest evaluations. This paper provides a: detailed test overview; comprehensive data update for the first 5 years of test operations; summary of experiment observations; initial data interpretations; and, several status; experimental objectives -- how these tests support WIPP TRU waste acceptance, performance assessment studies, underground operations, and the overall WIPP mission; and, in situ performance evaluations of RH TRU waste package materials plus design details and options. We provide instrument data and results for in situ waste container and borehole temperatures, pressures exerted on test containers through the backfill materials, and vertical and horizontal borehole-closure measurements and rates. The effects of heat on borehole closure, fracturing, and near-field materials (metals, backfills, rock salt, and intruding brine) interactions were closely monitored and are summarized, as are assorted test observations. Predictive 3-dimensional thermal and structural modeling studies of borehole and room closures and temperature fields were also performed

An isotopic analysis system for plutonium samples enriched in 238Pu

International Nuclear Information System (INIS)

Ruhter, W.D.; Camp, D.C.

1991-08-01

We have designed and built a gamma-ray spectrometer system that measures the relative plutonium isotopic abundances of plutonium oxide enriched in 238 Pu. The first system installed at Westinghouse Savannah River Company was tested and evaluated on plutonium oxide in stainless steel EP60/61 containers. 238 Pu enrichments ranged from 20% to 85%. Results show that 200 grams of plutonium oxide in an EP60.61 container can be measured with ±0.3% precision and better than ±1.0% accuracy in the specific power using a counting time of 50 minutes. 3 refs., 2 figs

TRU Waste Sampling Program: Volume I. Waste characterization

International Nuclear Information System (INIS)

Clements, T.L. Jr.; Kudera, D.E.

1985-09-01

Volume I of the TRU Waste Sampling Program report presents the waste characterization information obtained from sampling and characterizing various aged transuranic waste retrieved from storage at the Idaho National Engineering Laboratory and the Los Alamos National Laboratory. The data contained in this report include the results of gas sampling and gas generation, radiographic examinations, waste visual examination results, and waste compliance with the Waste Isolation Pilot Plant-Waste Acceptance Criteria (WIPP-WAC). A separate report, Volume II, contains data from the gas generation studies

Los Alamos controlled air incinerator upgrade for TRU/mixed waste operations

International Nuclear Information System (INIS)

Vavruska, J.S.; Borduin, L.C.; Hutchins, D.A.; Warner, C.L.; Thompson, T.K.

1989-01-01

The Los Alamos Controlled Air Incinerator (CAI) is undergoing a major process upgrade to accept Laboratory-generated transuranic (TRU) and TRU mixed wastes on a production basis. In the interim,prior to the scheduled 1992 operation of a new on-site LLW/mixed waste incinerator, the CAI will also be accepting solid and liquid low-level mixed wastes. This paper describes major modifications that have been made to the process to enhance safety and ensure reliability for long-term, routine waste incineration operations. The regulatory requirements leading to operational status of the system are also briefly described. The CAI was developed in the mid-1970s as a demonstration system for volume reduction of TRU combustible solid wastes. It continues as a successful R and D system well into the 1980s during which incineration tests on a wide variety of radioactive and chemical waste forms were performed. In 1985, a DOE directive required Los Alamos to reduce the volume of its TRU waste prior to ultimate placement in the geological repository at the Waste Isolation Pilot Project (WIPP). With only minor modifications to the original process flowsheet, the Los Alamos CAI was judged capable of conversion to a TRU waste operations mode. 9 refs., 1 fig

Relative 238Pu content of bone and bone marrow

International Nuclear Information System (INIS)

McClanahan, B.J.

1979-01-01

Selected bones from a dog that inhaled 238 PuO 2 were subjected to ultrasonic cell disruption to separate the marrow elements from bone, in order to determine the plutonium content of the two components of the skeleton

TRU waste certification and TRUPACT-2 payload verification

International Nuclear Information System (INIS)

Hunter, E.K.; Johnson, J.E.

1990-01-01

The Waste Isolation Pilot Plant (WIPP) established a policy that requires each waste shipper to verify that all waste shipments meet the requirements of the Waste Acceptance Criteria (WAC) prior to being shipped. This verification provides assurance that transuranic (TRU) wastes meet the criteria while still retained in a facility where discrepancies can be immediately corrected. Each Department of Energy (DOE) TRU waste facility planning to ship waste to the Waste Isolation Pilot Plant (WIPP) is required to develop and implement a specific program including Quality Assurance (QA) provisions to verify that waste is in full compliance with WIPP's WAC. This program is audited by a composite DOE and contractor audit team prior to granting the facility permission to certify waste. During interaction with the Nuclear Regulatory Commission (NRC) on payload verification for shipping in TRUPACT-II, a similar system was established by DOE. The TRUPACT-II Safety Analysis Report (SAR) contains the technical requirements and physical and chemical limits that payloads must meet (like the WAC). All shippers must plan and implement a payload control program including independent QA provisions. A similar composite audit team will conduct preshipment audits, frequent subsequent audits, and operations inspections to verify that all TRU waste shipments in TRUPACT-II meet the requirements of the Certificate of Compliance issued by the NRC which invokes the SAR requirements. 1 fig

Biokinetics aand dosimetry of inhaled 238PuO2 in the beagle dog: An update

International Nuclear Information System (INIS)

Guilmette, R.A.; Griffith, W.C.; Diel, J.H.

1994-01-01

The temporal and spatial distributions of 238 Pu have been measured during the course of a dose-response study of the biological effects of inhaled 238 PuO 2 in Beagle dogs. These measurements were done on the dose-response study animals, as well as a separate group of dogs exposed to similar aerosols and killed serially out to 4 y after exposure. The data from this latter group provided the basis for the development of a biokinetic/dosimetric model for 238 PuO 2 in dogs. Since the publication of this model, several important findings have been made that affected the dosimetric evaluations. The first involved the discovery of significant quantities of natural uranium (U) in the feces samples. The U was measured with the plutonium (Pu), which inflated the values for purported Pu in feces. The second finding involved the addition of Pu biokinetics data from the dose-response dogs, which increased the period of observation from 4 y to 15 y; these later data were not consistent with the earlier model predictions. The purpose of this investigation was (1) to remove the analytical bias in the 238 Pu radiochemical data due to the U and (2) to modify the original model of Mewhinney and Diel, taking into account all data from both studies

Direct reduction of 238PuO2 and 239PuO2 to metal

International Nuclear Information System (INIS)

Mullins, L.J.; Foxx, C.L.

1982-02-01

The process for reducing 700 g 239 PuO 2 to metal is a standard procedure at Los Alamos National Laboratory. This process is based on research for reducing 200 g 238 PuO 2 to metal. This report describes in detail the experiments and development of the 200-g process. The procedure uses calcium metal as the reducing agent in a molten CaCl 2 solvent system. The process to convert impure plutonia to high-purity metal by oxide reduction followed by electrorefining is also described

Development of waste packages for TRU-disposal. 5. Development of cylindrical metal package for TRU wastes

International Nuclear Information System (INIS)

Mine, Tatsuya; Mizubayashi, Hiroshi; Asano, Hidekazu; Owada, Hitoshi; Otsuki, Akiyoshi

2005-01-01

Development of the TRU waste package for hulls and endpieces compression canisters, which include long-lived and low sorption nuclides like C-14 is essential and will contribute a lot to a reasonable enhancement of safety and economy of the TRU-disposal system. The cylindrical metal package made of carbon steel for canisters to enhance the efficiency of the TRU-disposal system and to economically improve their stacking conditions was developed. The package is a welded cylindrical construction with a deep drawn upper cover and a disc plate for a bottom cover. Since the welding is mainly made only for an upper cover and a bottom disc plate, this package has a better containment performance for radioactive nuclide and can reduce the cost for construction and manufacturing including its welding control. Furthermore, this package can be laid down in pile for stacking in the circular cross section disposal tunnel for the sedimentary rock, which can drastically minimize the space for disposal tunnel as mentioned previously in TRU report. This paper reports the results of the study for application of newly developed metal package into the previous TRU-disposal system and for the stacking equipment for the package. (author)

Hanford Site Transuranic (TRU) Waste Certification Plan

Energy Technology Data Exchange (ETDEWEB)

GREAGER, T.M.

1999-09-09

The Hanford Site Transuranic Waste Certification Plan establishes the programmatic framework and criteria within which the Hanford Site ensures that contract-handled TRU wastes can be certified as compliant with the WIPP WAC and TRUPACT-II SARP.

Nuclear-waste-management technical support in the development of nuclear-waste-form criteria for the NRC. Task 2. Alternative TRU technologies

International Nuclear Information System (INIS)

Bida, G.; MacKenzie, D.R.

1982-02-01

Three main areas of transuranic (TRU) waste management are addressed: immobilization processes and waste forms for ultimate geologic disposal of TRU waste; decontamination as a method for TRU waste management; and potential problems associated with gas generation by certain TRU wastes. Waste forms are considered in terms of the regulations and criteria proposed in 10 CFR 60. Evaluation of the waste forms is based principally on ability to meet the release rate criterion of 10 -5 /year given in the Performance Objectives of Section 111, but also on the general requirements of Section 133. The two classes of metallic waste which are candidates for decontamination treatment are Zircaloy cladding hulls from light water reactor fuel elements, and failed facilities and equipment. Decontamination methods are addressed with regard to their ability to remove contamination to a level below the 10 nCi/g TRU limit. Other important factors are the volume reduction achieved, and compatibility of the secondary waste streams with acceptable waste forms. Gas generation by combustible TRU wastes and cast concretes containing TRU isotopes is discussed, and its potential for damage to a geologic repository is considered. Exclusion of combustible TRU waste from repositories is recommended. Conclusions are drawn about the suitability of various waste forms and recommendations are made regarding further work needed in the development of specific TRU waste forms

Evaluation of fission cross sections and covariances for 233U, 235U, 238U, 239Pu, 240Pu, and 241Pu

International Nuclear Information System (INIS)

Kawano, Toshihiko; Matsunobu, Hiroyuki; Murata, Toru

2000-02-01

A simultaneous evaluation code SOK (Simultaneous evaluation on KALMAN) has been developed, which is a least-squares fitting program to absolute and relative measurements. The SOK code was employed to evaluate the fission cross sections of 233 U, 235 U, 238 U, 239 Pu, 240 Pu, and 241 Pu for the evaluated nuclear data library JENDL-3.3. Procedures of the simultaneous evaluation and the experimental database of the fission cross sections are described. The fission cross sections obtained were compared with evaluated values given in JENDL-3.2 and ENDF/B-VI. (author)

Test Plan: WIPP bin-scale CH TRU waste tests

International Nuclear Information System (INIS)

Molecke, M.A.

1990-08-01

This WIPP Bin-Scale CH TRU Waste Test program described herein will provide relevant composition and kinetic rate data on gas generation and consumption resulting from TRU waste degradation, as impacted by synergistic interactions due to multiple degradation modes, waste form preparation, long-term repository environmental effects, engineered barrier materials, and, possibly, engineered modifications to be developed. Similar data on waste-brine leachate compositions and potentially hazardous volatile organic compounds released by the wastes will also be provided. The quantitative data output from these tests and associated technical expertise are required by the WIPP Performance Assessment (PA) program studies, and for the scientific benefit of the overall WIPP project. This Test Plan describes the necessary scientific and technical aspects, justifications, and rational for successfully initiating and conducting the WIPP Bin-Scale CH TRU Waste Test program. This Test Plan is the controlling scientific design definition and overall requirements document for this WIPP in situ test, as defined by Sandia National Laboratories (SNL), scientific advisor to the US Department of Energy, WIPP Project Office (DOE/WPO). 55 refs., 16 figs., 19 tabs

Hanford Site Transuranic (TRU) Waste Certification Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

1999-01-01

The Hanford Site Transuranic Waste Certification Plan establishes the programmatic framework and criteria with in which the Hanford Site ensures that contract-handled TRU wastes can be certified as compliant with the WIPP WAC and TRUPACT-II SARP

The new Japanese policy for TRU-waste management

International Nuclear Information System (INIS)

Yamamoto, M.

1992-01-01

In July 1991, the Advisory Committee on Radioactive Waste of the Japan Atomic Energy Commission announced its report on a new Japanese policy for TRU-waste management. The total volume of radioactive wastes which contain TRU nuclides has reached the equivalent of about 40,000,200-liter drums, and is expected to grow to about 300,000 drums by the year 2010. Further development is required to reduce the volume of the existing waste and to decrease the amount of waste being generated. Wastes with concentration levels exceeding a threshold limit of 1 Giga-Becquerel per ton will be disposed in an underground facility. Those wastes with lower activities will be sent to a shallow-land burial facility. The goal of research and development is the completion of the disposal system by the late 1990's. (author)

Wood fibre density measurement with 238 Pu radiation

International Nuclear Information System (INIS)

Barry, B.J.; Baker, D.B.

1996-01-01

The form of the curve of attenuation by wood fibre of the X radiation from 238 Pu has been determined. An exponential function containing a term second order in the areal density of the fibre described the curve accurately. The effect of scatter is negligible, even with an uncollimated radiation beam. (author). 18 refs., 1 tab., 6 figs

Guidelines for developing certification programs for newly generated TRU waste

International Nuclear Information System (INIS)

Whitty, W.J.; Ostenak, C.A.; Pillay, K.K.S.; Geoffrion, R.R.

1983-05-01

These guidelines were prepared with direction from the US Department of Energy (DOE) Transuranic (TRU) Waste Management Program in support of the DOE effort to certify that newly generated TRU wastes meet the Waste Isolation Pilot Plant (WIPP) Waste Acceptance Criteria. The guidelines provide instructions for generic Certification Program preparation for TRU-waste generators preparing site-specific Certification Programs in response to WIPP requirements. The guidelines address all major aspects of a Certification Program that are necessary to satisfy the WIPP Waste Acceptance Criteria and their associated Compliance Requirements and Certification Quality Assurance Requirements. The details of the major element of a Certification Program, namely, the Certification Plan, are described. The Certification Plan relies on supporting data and control documentation to provide a traceable, auditable account of certification activities. Examples of specific parts of the Certification Plan illustrate the recommended degree of detail. Also, a brief description of generic waste processes related to certification activities is included

Savannah River Plant 200 Area technical manual. Part SP. Processing of Np/sup 237/ and Pu/sup 238/

Energy Technology Data Exchange (ETDEWEB)

Hill, A.J. (comp.)

1963-01-03

This manual covers the technology involved in the 200 Area process for the recovery of Np/sup 237/ from certain aqueous waste streams in the separations plants, for the recovery of NP/sup 237/ and Pu/sup 238/ from irradiated NpO/sub 2/-Al slugs and for the fabrication of NpO/sub 2/-Al slugs. The manual contains sections on the fundamental chemistry, the primary recovery of Np by ion exchange, the decontamination of Np by ion exchange, the processing of NpO/sub 2/-Al targets, the separation and purification of Np/sup 237/ and Pu/sup 238/, the finishing of Np, the preparation of NpO/sub 2/, the disposal of spent resin, and the safety aspects of the handling of hydrazine. The section on the fabrication of NpO/sub 2/-Al slugs will be added later. 76 refs., 22 figs.

Repackaging SRS Black Box TRU Waste

International Nuclear Information System (INIS)

Swale, D. J.; Stone, K.A.; Milner, T. N.

2006-01-01

Historically, large items of TRU Waste, which were too large to be packaged in drums for disposal have been packaged in various sizes of custom made plywood boxes at the Savannah River Site (SRS), for many years. These boxes were subsequently packaged into large steel ''Black Boxes'' for storage at SRS, pending availability of Characterization and Certification capability, to facilitate disposal of larger items of TRU Waste. There are approximately 107 Black Boxes in inventory at SRS, each measuring some 18' x 12' x 7', and weighing up to 45,000 lbs. These Black Boxes have been stored since the early 1980s. The project to repackage this waste into Standard Large Boxes (SLBs), Standard Waste Boxes (SWB) and Ten Drum Overpacks (TDOP), for subsequent characterization and WIPP disposal, commenced in FY04. To date, 10 Black Boxes have been repackaged, resulting in 40 SLB-2's, and 37 B25 overpack boxes, these B25's will be overpacked in SLB-2's prior to shipping to WIPP. This paper will describe experience to date from this project

A reactivity hold-down strategy for soluble boron free operation by introducing Pu-238 added fuel

International Nuclear Information System (INIS)

Kim, Soon Young; Kim, Jong Kyung

2000-01-01

A new concept of Pu-238 added fuel is introduced to control the reactivity and power distribution in soluble boron free (SBF) pressurized water reactor (PWR) core. Though extensive use of burnable poison and control rods is inevitable for reactivity suppression in SBF core, it causes the core power distribution control to be so difficult that a practical SBF operation is far distant. In this work, it is confirmed that the excess reactivity can be greatly suppressed by introducing the Pu-238 added fuel. As a result of the conceptual core design of the 600 MWe SBF PWR using Pu-238 added fuel, the core reactivity is well controlled in comparison with the results obtained from the earlier 600 MWe SBF core design works. Especially, the axial power shape control is performed successfully with the aid of simple axial zoning scheme, developed in this study, by using Pu-238 enrichment zoning. The Pu-238 added fuel is also tested for 1300 MWe SBF PWR core design, in which the power distribution control can be more difficult than that of smaller plants if soluble boron control is not available. The results show that the core excess reactivity and the power distribution can be well controlled without using soluble boron even in a large-sized PWR. Hence, one of the difficult control problems arising in SBF core design can be greatly mitigated by introducing the new fuel concept. It is further expected that the Pu-238 added fuel, the simple axial zoning scheme, and the control bank operation strategy introduced in this study are directly applicable to practical SBF core design

Toxicity of inhaled 238PuO2 I

International Nuclear Information System (INIS)

Diel, J.H.; Mewhinney, J.A.

1980-01-01

The deposition, retention, translocation and microscopic distribution of inhaled 238 PuO 2 particles were studied to better define the organs at risk and uniformity of dose and cell types or structures at risk in the lung. Beagle dogs were exposed once by inhalation to an aerosol of 238 PuO 2 with particle aerodynamic diameters of 0.7, 1.4, or 2.7 μm (+-10%). Initial burdens averaged about 700 nCi, a level not expected to induce life-shortening effects in Beagle dogs. Animals were sacrificed at times from 4 hours to 2 years after exposure. Whole body retention of plutonium and its distribution among organs in the sacrificed animals was determined by radiochemical analysis for plutonium content of excreta and tissue samples. The distribution of particles in lung was determined using autoradiographs of lung tissue sections and computer-assisted data collection and analysis. Soon after exposure, PuO 2 was relatively insoluble in lung with individual particles being randomly distributed throughout the lung. A distinct change in the rate of dissolution from lung occurred at about 100 days after exposure resulting in decreased pulmonary retention and increased uptake by liver and skeleton. Particle breakup was observed in autoradiographs for time periods in excess of 128 days after exposure. Broken up particles dissolved rapidly leaving little residue in the lung. The remaining particles were randomly distributed in the lung. These results are discussed in relation to current radiation protection guides for plutonium radionuclides. (author)

Risk estimates for lung tumours from inhaled 239PuO2, 238PuO2, and 239Pu(NO3)4 in beagle dogs

International Nuclear Information System (INIS)

Dagle, G.E.; Park, J.F.; Gilbert, E.S.; Weller, R.E.

1989-01-01

Lung cancer risks are being studied in beagle dogs given single exposures to aerosols of 239 PuO 2 , 238 PuO 2 , or 239 Pu(NO 3 ) 4 . A major objective of these studies is to examine the risk of lung cancer relative to the specific activity of the radionuclide, rate of dose accumulation due to differences in solubilities of the radionuclides, and the presence of competing risk from extrapulmonary lesions. Dose-response relationships were studied for the three groups of dogs, with analyses specifically designed to evaluate differences in response. Based on estimated cumulative dose to the lung, risks were found to differ significantly among the radionuclides; they were highest for 239 Pu(NO 3 ) 4 and lowest for 238 PuO 2 . A model in which the risk was assumed to be a pure quadratic function of dose fitted the data much better than a pure linear model. Currently, all three groups of dogs can be compared only to 10 years after exposure. However, it is apparent that the average cumulative dose to the lung may not be an adequate predictor of lung cancer risk for different isotopic and physicochemical forms of plutonium. (author)

Hybrid Microwave Treatment of SRS TRU and Mixed Wastes

International Nuclear Information System (INIS)

Wicks, G.G.

1999-01-01

A new process, using hybrid microwave energy, has been developed as part of the Strategic Research and Development program and successfully applied to treatment of a wide variety of non-radioactive materials, representative of SRS transuranic (TRU) and mixed wastes. Over 35 simulated (non-radioactive) TRU and mixed waste materials were processed individually, as well as in mixed batches, using hybrid microwave energy, a new technology now being patented by Westinghouse Savannah River Company (WSRC)

Waste Disposition Issues and Resolutions at the TRU Waste Processing Center at Oak Ridge TN

International Nuclear Information System (INIS)

Gentry, R.

2009-01-01

This paper prepared for the Waste Management Conference 2009 provides lessons learned from the Transuranic (TRU) Waste Processing Center (TWPC) associated with development of approaches used to certify and ensure disposition of problematic TRU wastes at the Waste Isolation Pilot Plant (WIPP) site. The TWPC is currently processing the inventory of available waste TRU waste at the Oak Ridge National Lab (ORNL). During the processing effort several waste characteristics were identified/discovered that did not conform to the normal standards and processes for disposal at WIPP. Therefore, the TWPC and ORNL were challenged with determining a path forward for this problematic, special case TRU wastes to ensure that they can be processed, packaged, and shipped to WIPP. Additionally, unexpected specific waste characteristics have challenged the project to identify and develop processing methods to handle problematic waste. The TWPC has several issues that have challenged the projects ability to process RH Waste. High Neutron Dose Rate resulting from both Californium and Curium in the waste stream challenge the RH-TRU 72-B limit for dose rate measured from the side of the package under normal conditions of transport, as specified in Chapter 5.0 of the RH-TRU 72-B SAR (i.e., ≤10 mrem/hour at 2 meters). Difficult to process waste in the hot cell has introduced processing and handling difficulties included problems associated with the disposition of prohibited items that fall out of the waste stream such as liquids, aerosol cans, etc. Lastly, multiple waste streams require characterization and AK challenge the ability to generate dose-to curie models for the waste. Repackaging is one solution to the high neutron dose rate issue. In parallel, an effort is underway to request a change to the TRAMPAC requirements to allow shielding in the drum or canister to reduce the impact of the high neutron dose rates. Due diligence on supporting AK efforts is important in ensuring adequate

Design improvements for gloveboxes used [in] 238PuO2 process operations

International Nuclear Information System (INIS)

George, T.G.

1997-01-01

238 PuO 2 process operations are housed in a complex of 76 gloveboxes and introductory hoods connected by means of an overhead trolley housed in a tunnel. Because a significant number of the gloveboxes used for 238 PuO 2 processing were installed before the original startup of the facility in 1978, they have been in service for nearly 20 years. During a recent heat source production campaign, numerous contamination releases in the 238 PuO 2 processing area were traced to degraded elastomer gaskets used for glovebox connections, and attachment of feed-throughs, service panels, and windows. Evaluation of the degraded gaskets revealed that a combination of radiolytic degradation related to the high specific activity of 238 Pu, and extended service at high altitude in a low (to extremely low) humidity environment had resulted in accelerated gasket aging. However, it was also apparent that gasket design was the most important factor in actual contamination release. All of the contamination releases that were traced to degraded gaskets occurred in variations of a design that used a spline to expand an elastomeric gasket into the space between a connecting flange, window, or service panel, and a glovebox opening. No contamination releases were traced to the gasket design that employed bolted clamps to compress the gasket between a connecting flange, window, or panel, and the exterior surface of a glovebox opening. As a result of these findings, the Actinide Ceramics group at LANL (NMT-9) has initiated a routine replacement and upgrade program to replace aging gloveboxes. All of the new gloveboxes will utilize the preferred gasket design, which is expected to reduce the number and frequency of contamination releases

TRU waste certification and TRUPACT-II payload verification

International Nuclear Information System (INIS)

Hunter, E.K.; Johnson, J.E.

1990-01-01

The Waste Isolation Pilot Plant (WIPP) established a policy (subsequently confirmed and required by DOE Order 5820.2A, Radioactive Waste Management, September 1988) that requires each waste shipper to verify that all waste shipments meet the requirements of the Waste Acceptance Criteria (WAC) prior to being shipped. This verification provides assurance that transuranic (TRU) wastes meet the criteria while still retained in a facility where discrepancies can be immediately corrected. In this manner, problems that would arise if WAC violations were discovered at the receiver, where corrective facilities are not available, are avoided. Each Department of Energy (DOE) TRU waste facility planning to ship waste to the Waste Isolation Pilot Plant (WIPP) is required to develop and implement a specific program including Quality Assurance (QA) provisions to verify that waste is in full compliance with WIPP's WAC. This program is audited by a composite DOE and contractor audit team prior to granting the facility permission to certify waste. During interaction with the Nuclear Regulatory Commission (NRC) on payload verification for shipping in TRUPACT-II, a similar system was established by DOE. The TRUPACT-II Safety Analysis Report (SAR) contains the technical requirements and physical and chemical limits that payloads must meet (like the WAC). All shippers must plan and implement a payload control program including independent QA provisions. A similar composite audit team will conduct preshipment audits, frequent subsequent audits, and operations inspections to verify that all TRU waste shipments in TRUPACT-II meet the requirements of the Certificate of Compliance (C of C) issued by the NRC which invokes the SAR requirements. 1 fig

Los Alamos National Laboratory accelerated tru waste workoff strategies

International Nuclear Information System (INIS)

Kosiewicz, S.T.; Triay, I.R.; Rogers, P.Z.; Christensen, D.V.

1997-01-01

During 1996, the Los Alamos National Laboratory (LANL) developed two transuranic (TRU) waste workoff strategies that were estimated to save $270 - 340M through accelerated waste workoff and the elimination of a facility. The planning effort included a strategy to assure that LANL would have a significant quantity (3000+ drums) of TRU waste certified for shipment to the Waste Isolation Pilot Plant (WIPP) beginning in April of 1998, when WIPP was projected to open. One of the accelerated strategies can be completed in less than ten years through a Total Optimization of Parameters Scenario (open-quotes TOPSclose quotes). open-quotes TOPSclose quotes fully utilizes existing LANL facilities and capabilities. For this scenario, funding was estimated to be unconstrained at $23M annually to certify and ship the legacy inventory of TRU waste at LANL. With open-quotes TOPSclose quotes the inventory is worked off in about 8.5 years while shipping 5,000 drums per year at a total cost of $196M. This workoff includes retrieval from earthen cover and interim storage costs. The other scenario envisioned funding at the current level with some increase for TRUPACT II loading costs, which total $16M annually. At this funding level, LANL estimates it will require about 17 years to work off the LANL TRU legacy waste while shipping 2,500 drums per year to WIPP. The total cost will be $277M. This latter scenario decreases the time for workoff by about 19 years from previous estimates and saves an estimated $190M. In addition, the planning showed that a $70M facility for TRU waste characterization was not needed. After the first draft of the LANL strategies was written, Congress amended the WIPP Land Withdrawal Act (LWA) to accelerate the opening of WIPP to November 1997. Further, the No Migration Variance requirement for the WIPP was removed. This paper discusses the LANL strategies as they were originally developed. 1 ref., 3 figs., 2 tabs

Observed TRU data from nuclear utility waste streams

International Nuclear Information System (INIS)

Wessman, R.A.; Floyd, J.G.; Leventhal, L.

1990-01-01

TMA/Norcal has performed 10CFR61 analysis of radioactive waste streams from BWR's and PWR's since 1983. Many standard and non-routine sample types have been received for analysis from nuclear power plants nation-wide. In addition to the 10CFR61 Tables I and II analyses, we also have analyzed for many of the supplementary isotopes. As part of this program TRU analyses are required. As a result, have accumulated a significant amount of data for plutonium, americium, and curium in radioactive waste for many different sample matrices from many different waste streams. This paper will present our analytical program for 10CFR61 TRU. The laboratory methodology including chemical and radiometric procedures is discussed. The sensitivity of our measurements and ability to meet the lower limits of detection is also discussed. Secondly, a review of TRU data is presented. Scaling factors and their ranges from selected PWR stations are included. We discuss some features of, and limits to, interpretation of these data. 8 refs., 3 tabs

238Pu - Comments on Evaluation of Decay Data

International Nuclear Information System (INIS)

Chechev, V. P.

2013-01-01

This evaluation was done originally in March 2003, corrected in June 2004, and then updated in June 2009 with a literature cut-off by the same date. Decay Scheme: The decay scheme is based on 2007Br04. Some expected weak gamma-ray transitions were not observed directly in 238 Pu α-decay but have been adopted from decay of 234 Pa and 234 Np

Final environmental assessment: TRU waste drum staging building, Technical Area 55, Los Alamos National Laboratory

International Nuclear Information System (INIS)

1996-01-01

Much of the US Department of Energy's (DOE's) research on plutonium metallurgy and plutonium processing is performed at Los Alamos National Laboratory (LANL), in Los Alamos, New Mexico. LANL's main facility for plutonium research is the Plutonium Facility, also referred to as Technical Area 55 (TA-55). The main laboratory building for plutonium work within the Plutonium Facility (TA-55) is the Plutonium Facility Building 4, or PF-4. This Environmental Assessment (EA) analyzes the potential environmental effects that would be expected to occur if DOE were to stage sealed containers of transuranic (TRU) and TRU mixed waste in a support building at the Plutonium Facility (TA-55) that is adjacent to PF-4. At present, the waste containers are staged in the basement of PF-4. The proposed project is to convert an existing support structure (Building 185), a prefabricated metal building on a concrete foundation, and operate it as a temporary staging facility for sealed containers of solid TRU and TRU mixed waste. The TRU and TRU mixed wastes would be contained in sealed 55-gallon drums and standard waste boxes as they await approval to be transported to TA-54. The containers would then be transported to a longer term TRU waste storage area at TA-54. The TRU wastes are generated from plutonium operations carried out in PF-4. The drum staging building would also be used to store and prepare for use new, empty TRU waste containers

Capability to Recover Plutonium-238 in H-Canyon/HB-Line - 13248

Energy Technology Data Exchange (ETDEWEB)

Fuller, Kenneth S. Jr.; Smith, Robert H. Jr.; Goergen, Charles R. [Savannah River Nuclear Solutions, LLC, Savannah River Site, Aiken, SC 29802 (United States)

2013-07-01

Plutonium-238 is used in Radioisotope Thermoelectric Generators (RTGs) to generate electrical power and in Radioisotope Heater Units (RHUs) to produce heat for electronics and environmental control for deep space missions. The domestic supply of Pu-238 consists of scrap material from previous mission production or material purchased from Russia. Currently, the United States has no significant production scale operational capability to produce and separate new Pu-238 from irradiated neptunium-237 targets. The Department of Energy - Nuclear Energy is currently evaluating and developing plans to reconstitute the United States capability to produce Pu-238 from irradiated Np-237 targets. The Savannah River Site had previously produced and/or processed all the Pu-238 utilized in Radioisotope Thermoelectric Generators (RTGs) for deep space missions up to and including the majority of the plutonium for the Cassini Mission. The previous full production cycle capabilities included: Np- 237 target fabrication, target irradiation, target dissolution and Np-237 and Pu-238 separation and purification, conversion of Np-237 and Pu-238 to oxide, scrap recovery, and Pu-238 encapsulation. The capability and equipment still exist and could be revitalized or put back into service to recover and purify Pu-238/Np-237 or broken General Purpose Heat Source (GPHS) pellets utilizing existing process equipment in HB-Line Scrap Recovery, and H-Canyon Frame Waste Recovery processes. The conversion of Np-237 and Pu-238 to oxide can be performed in the existing HB-Line Phase-2 and Phase- 3 Processes. Dissolution of irradiated Np-237 target material, and separation and purification of Np-237 and Pu-238 product streams would be possible at production rates of ∼2 kg/month of Pu-238 if the existing H-Canyon Frames Process spare equipment were re-installed. Previously, the primary H-Canyon Frames equipment was removed to be replaced: however, the replacement project was stopped. The spare equipment

Pyrolysis/Steam Reforming Technology for Treatment of TRU Orphan Wastes

International Nuclear Information System (INIS)

Mason, J. B.; McKibbin, J.; Schmoker, D.; Bacala, P.

2003-01-01

Certain transuranic (TRU) waste streams within the Department of Energy (DOE) complex cannot be disposed of at the Waste Isolation Pilot Plant (WIPP) because they do not meet the shipping requirements of the TRUPACT-II or the disposal requirements of the Waste Analysis Plan (WAP) in the WIPP RCRA Part B Permit. These waste streams, referred to as orphan wastes, cannot be shipped or disposed of because they contain one or more prohibited items, such as liquids, volatile organic compounds (VOCs), hydrogen gas, corrosive acids or bases, reactive metals, or high concentrations of polychlorinated biphenyl (PCB), etc. The patented, non-incineration, pyrolysis and steam reforming processes marketed by THOR Treatment Technologies LLC removes all of these prohibited items from drums of TRU waste and produces a dry, inert, inorganic waste material that meets the existing TRUPACT-II requirements for shipping, as well as the existing WAP requirements for disposal of TRU waste at WIPP. THOR Treatment Technologies is a joint venture formed in June 2002 by Studsvik, Inc. (Studsvik) and Westinghouse Government Environmental Services Company LLC (WGES) to further develop and deploy Studsvik's patented THORSM technology within the DOE and Department of Defense (DoD) markets. The THORSM treatment process is a commercially proven system that has treated over 100,000 cu. ft. of nuclear waste from commercial power plants since 1999. Some of this waste has had contact dose rates of up to 400 R/hr. A distinguishing characteristic of the THORSM process for TRU waste treatment is the ability to treat drums of waste without removing the waste contents from the drum. This feature greatly minimizes criticality and contamination issues for processing of plutonium-containing wastes. The novel features described herein are protected by issued and pending patents

MWIR-1995 DOE national mixed and TRU waste database users guide

International Nuclear Information System (INIS)

1995-11-01

The Department of Energy (DOE) National 1995 Mixed Waste Inventory Report (MWIR-1995) Database Users Guide provides information on computer system requirements and describes installation, operation, and navigation through the database. The MWIR-1995 database contains a detailed, nationwide compilation of information on DOE mixed waste streams and treatment systems. In addition, the 1995 version includes data on non- mixed, transuranic (TRU) waste streams. These were added to the data set as a result of coordination of the 1995 update with the National Transuranic Program Office's (NTPO's) data needs to support the Waste Isolation Pilot Plant (WIPP) TRU Waste Baseline Inventory Report (WTWBIR). However, the information on the TRU waste streams is limited to that associated with the core mixed waste data requirements. The additional, non-core data on TRU streams collected specifically to support the WTWBIR is not included in the MWIR-1995 database. With respect to both the mixed and TRU waste stream data, the data set addresses open-quotes storedclose quotes streams. In this instance, open-quotes storedclose quotes streams are defined as (a) streams currently in storage at both EM-30 and EM-40 sites and (b) streams that have yet to be generated but are anticipated within the next five years from sources other than environmental restoration and decontamination and decommissioning (ER/D ampersand D) activities. Information on future ER/D ampersand D streams is maintained in the EM-40 core database. The MWIR-1995 database also contains limited information for both waste streams and treatment systems that have been removed or deleted since the 1994 MWIR. Data on these is maintained only through Section 2, Waste Stream Identification/Tracking/Source, to document the reason for removal from the data set

Transuranic advanced disposal systems: preliminary 239Pu waste-disposal criteria for Hanford

International Nuclear Information System (INIS)

Kennedy, W.E. Jr.; Napier, B.A.; Soldat, J.K.

1982-08-01

An evaluation of the feasibility and potential application of advanced disposal systems is being conducted for defense transuranic (TRU) wastes at the Hanford Site. The advanced waste disposal options include those developed to provide greater confinement than provided by shallow-land burial. An example systems analysis is discussed with assumed performance objectives and various Hanford-specific disposal conditions, waste forms, site characteristics, and engineered barriers. Preliminary waste disposal criteria for 239 Pu are determined by applying the Allowable Residual Contamination Level (ARCL) method. This method is based on compliance with a radiation dose rate limit through a site-specific analysis of the potential for radiation exposure to individuals. A 10,000 year environmental performance period is assumed, and the dose rate limit for human intrusion is assumed to be 500 mrem/y to any exposed individual. Preliminary waste disposal criteria derived by this method for 239 Pu in soils at the Hanford Site are: 0.5 nCi/g in soils between the surface and a depth of 1 m, 2200 nCi/g of soil at a depth of 5 m, and 10,000 nCi/g of soil at depths 10 m and below. These waste disposal criteria are based on exposure scenarios that reflect the dependence of exposure versus burial depth. 2 figures, 5 tables

PU-ICE Summary Information.

Energy Technology Data Exchange (ETDEWEB)

Moore, Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

The Generator Knowledge Report for the Plutonium Isentropic Compression Experiment Containment Systems (GK Report) provides information for the Plutonium Isentropic Compression Experiment (Pu- ICE) program to support waste management and characterization efforts. Attachment 3-18 presents generator knowledge (GK) information specific to the eighteenth Pu-ICE conducted in August 2015, also known as ‘Shot 18 (Aug 2015) and Pu-ICE Z-2841 (1).’ Shot 18 (Aug 2015) was generated on August 28, 2015 (1). Calculations based on the isotopic content of Shot 18 (Aug 2015) and the measured mass of the containment system demonstrate the post-shot containment system is low-level waste (LLW). Therefore, this containment system will be managed at Sandia National Laboratory/New Mexico (SNL/NM) as LLW. Attachment 3-18 provides documentation of the TRU concentration and documents the concentration of any hazardous constituents.

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2007-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2006-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2005-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2004-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2008-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-09-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-05-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-02-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-06-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-06-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-01-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codesand corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-12-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-01-18

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2004-10-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-03-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-09-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2004-12-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-11-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-12-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-01-30

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-06-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

Automation of radiochemical analysis by flow injection techniques. Am-Pu separation using TRU-resinTM sorbent extraction column

International Nuclear Information System (INIS)

Egorov, O.; Washington Univ., Seattle, WA; Grate, J.W.; Ruzicka, J.

1998-01-01

A rapid automated flow injection analysis (FIA) procedure was developed for efficient separation of Am and Pu from each other and from interfering matrix and radionuclide components using a TRU-resin TM column. Selective Pu elution is enabled via on-column reduction. The separation was developed using on-line radioactivity detection. After the separation had been developed, fraction collection was used to obtain the separated fractions. In this manner, a FIA instrument functions as an automated separation workstation capable of unattended operation. (author)

A Novel and Cost Effective Approach to the Decommissioning and Decontamination of Legacy Glove Boxes - Minimizing TRU Waste and Maximizing LLW Waste - 13634

Energy Technology Data Exchange (ETDEWEB)

Pancake, Daniel; Rock, Cynthia M.; Creed, Richard [Argonne National Laboratory, 9700 South Cass Avenue, Lemont, IL 60439 (United States); Donohoue, Tom; Martin, E. Ray; Mason, John A. [ANTECH Corporation 9050 Marshall Court, Westminster, CO, 80031 (United States); Norton, Christopher J.; Crosby, Daniel [Environmental Alternatives, Inc., 149 Emerald Street, Suite R, Keene, NH 03431 (United States); Nachtman, Thomas J. [InstaCote, Inc., 160 C. Lavoy Road, Erie, MI, 48133 (United States)

2013-07-01

determine the TRU content of the boxes by assessing the activity of Am-241 (59 keV) and Pu-241 (414 keV). Using the data generated it was possible for qualified subject matter experts (SME) to assess that the gloveboxes could be consigned for disposition as LLW and not as TRU. Once this determination was assessed and accepted the gloveboxes were prepared for final disposition to the Nevada National Security Site (NNSS) - formerly the Nevada Test Site (NTS). This preparation involved fixing any remaining radioactive contamination within the gloveboxes by filling them with a foam compound, prior to transportation. Once the remaining contamination was fixed the gloveboxes were removed from the laboratory and prepared for transported by road to NNSS. This successful glovebox decontamination and decommissioning process illustrates the means by which TRU waste generation has been minimized, LLW generation has been maximized, and risk has been effectively managed. The process minimizes the volume of TRU waste and reduced the decommissioning time with significant cost savings as the result. (authors)

A Novel and Cost Effective Approach to the Decommissioning and Decontamination of Legacy Glove Boxes - Minimizing TRU Waste and Maximizing LLW Waste - 13634

International Nuclear Information System (INIS)

Pancake, Daniel; Rock, Cynthia M.; Creed, Richard; Donohoue, Tom; Martin, E. Ray; Mason, John A.; Norton, Christopher J.; Crosby, Daniel; Nachtman, Thomas J.

2013-01-01

determine the TRU content of the boxes by assessing the activity of Am-241 (59 keV) and Pu-241 (414 keV). Using the data generated it was possible for qualified subject matter experts (SME) to assess that the gloveboxes could be consigned for disposition as LLW and not as TRU. Once this determination was assessed and accepted the gloveboxes were prepared for final disposition to the Nevada National Security Site (NNSS) - formerly the Nevada Test Site (NTS). This preparation involved fixing any remaining radioactive contamination within the gloveboxes by filling them with a foam compound, prior to transportation. Once the remaining contamination was fixed the gloveboxes were removed from the laboratory and prepared for transported by road to NNSS. This successful glovebox decontamination and decommissioning process illustrates the means by which TRU waste generation has been minimized, LLW generation has been maximized, and risk has been effectively managed. The process minimizes the volume of TRU waste and reduced the decommissioning time with significant cost savings as the result. (authors)

Risk estimates for lung tumors from inhaled 239PuO2, 238PuO2, and /sup 239Pu/(NO3)4 in beagle dogs

International Nuclear Information System (INIS)

Dagle, G.E.; Park, J.F.; Gilbert, E.S.; Weller, R.E.

1988-06-01

Lung-cancer risks are being studied in beagle dogs given single exposures to aerosols of 239 PuO 2 , 238 PuO 2 , or 239 Pu(NO 3 ) 4 . A major objective of these studies is to examine the risk of lung cancer relative to the specific activity of the radionuclide, rate of dose accumulation due to differences in solubilities of the radionuclides, and the presence of competing risk from extrapulmonary lesions. Dose-response relationships were studied for the three groups of dogs, with analyses specifically designed to evaluate differences in response. Based on estimated cumulative dose to the lung, risks were found to differ significantly among the radionuclides; they were highest for 239 Pu(NO 3 ) 4 and lowest for 238 PuO 2 . A model in which the risk was assumed to be a pure quadratic function of dose fit the data much better than a pure linear model. Currently, all three groups of dogs can be compared only to 10 years after exposure. However, it is apparent that the average cumulative dose to the lung may not be an adequate predictor of lung-cancer risk for different isotopic and physicochemical forms of plutonium. 13 refs., 2 tabs

Final report on production of Pu-238 in commercial power reactors: target fabrication, postirradiation examination, and plutonium and neptunium recovery

International Nuclear Information System (INIS)

Pobereskin, M.; Langendorfer, W.; Lowry, L.; Farmelo, D.; Scotti, V.; Kruger, O.

1975-01-01

Considerable interest has been generated in more extensive applications of radioisotope thermoelectric generator (RTG) systems. This raises questions concerning the availability of 238 Pu to supply an expanding demand. The development of much of this demand will depend upon a considerable reduction in cost of 238 Pu. Two neptunia--zirconia--fuel target rods, containing four sections each of different NpO 2 concentrations, were irradiated in the Connecticut Yankee Reactor for approximately one year. Following irradiation both target rods were subjected to nondestructive examination. One rod was chosen for destructive testing and analysis. Post-irradiation chemical analyses included total Pu and Np, ppM 236 Pu/ 238 Pu, and Pu isotopic abundance. The results of these analyses and of electron microprobe analysis which provided the relative Pu concentration across the pellet diameters are tabulated. It was concluded that the feasibility of all operations involved in the production of 238 Pu by irradiation of 237 NpO 2 targets in commercial nuclear power reactors was demonstrated and that the demonstration should be extended to a pilot-scale leading to installation of a full production capacity. (U.S.)

SEPARATION AND EXTRACTION OF PLUTONIUM IN MIXED WASTE

International Nuclear Information System (INIS)

Desrosiers, Arthur E.; Kaiser, Robert; Antkowiak, Jason; Desrosiers, Justin; Jondro, Josh; Kulczyk, Adam

2002-01-01

The Sonatol process uses ultrasonic agitation in fluorinated surfactant solutions to remove radioactive particles from surfaces. Filtering the suspended particles allows the solutions to be reused indefinitely. The current work applies the Sonatol process to the decontamination of heterogeneous legacy Pu-238 waste that exhibits excessive hydrogen gas generation, which prevents transportation of the waste to the Waste Isolation Pilot Plant. Bartlett Services, Inc. (BSI) designed and fabricated a prototype decontamination system within a replica of a Savannah River Site glovebox. In Phase I, BSI conducted cold testing with surrogate waste material to verify that the equipment, operating procedures, and test protocols would support testing with Pu-238 in Phase II. The surrogate waste material is representative of known constituents of legacy job control waste. Two sub-micron sized Pu-238 simulants were added to the surrogate waste so that decontamination could be tested. The first simulant was an Osram Sylvania Phosphor 2284C powder that fluoresces under ultraviolet light. The use of the fluorescent simulant allows rapid, inexpensive system startup testing because residuals can be assayed using a digital camera. The results of digital pixel analysis (DPA) are available immediately and do not require use of licensed material. The second simulant, which was used for integrated cold testing, was a cerium oxide powder that was activated in a research reactor neutron flux and assayed by photon spectroscopy. The surrogate transuranic (TRU) waste material was contaminated with Pu-238 simulants and loaded into the cleaning chamber, where the surrogates were ultrasonically agitated and rinsed. The decontaminated materials were then assayed for surface contamination by DPA to establish optimum operating parameters and provide process quality control. Selected samples were sent to the Massachusetts Institute of Technology for neutron activation analysis (NAA). NAA testing

SEPARATION AND EXTRACTION OF PLUTONIUM IN MIXED WASTE

Energy Technology Data Exchange (ETDEWEB)

Arthur E. Desrosiers, ScD, CHP; Robert Kaiser, ScD; Jason Antkowiak; Justin Desrosiers; Josh Jondro; Adam Kulczyk

2002-12-13

The Sonatol process uses ultrasonic agitation in fluorinated surfactant solutions to remove radioactive particles from surfaces. Filtering the suspended particles allows the solutions to be reused indefinitely. The current work applies the Sonatol process to the decontamination of heterogeneous legacy Pu-238 waste that exhibits excessive hydrogen gas generation, which prevents transportation of the waste to the Waste Isolation Pilot Plant. Bartlett Services, Inc. (BSI) designed and fabricated a prototype decontamination system within a replica of a Savannah River Site glovebox. In Phase I, BSI conducted cold testing with surrogate waste material to verify that the equipment, operating procedures, and test protocols would support testing with Pu-238 in Phase II. The surrogate waste material is representative of known constituents of legacy job control waste. Two sub-micron sized Pu-238 simulants were added to the surrogate waste so that decontamination could be tested. The first simulant was an Osram Sylvania Phosphor 2284C powder that fluoresces under ultraviolet light. The use of the fluorescent simulant allows rapid, inexpensive system startup testing because residuals can be assayed using a digital camera. The results of digital pixel analysis (DPA) are available immediately and do not require use of licensed material. The second simulant, which was used for integrated cold testing, was a cerium oxide powder that was activated in a research reactor neutron flux and assayed by photon spectroscopy. The surrogate transuranic (TRU) waste material was contaminated with Pu-238 simulants and loaded into the cleaning chamber, where the surrogates were ultrasonically agitated and rinsed. The decontaminated materials were then assayed for surface contamination by DPA to establish optimum operating parameters and provide process quality control. Selected samples were sent to the Massachusetts Institute of Technology for neutron activation analysis (NAA). NAA testing

Long term stability of yttria-stabilized zirconia waste forms. Stability for secular change of partitioned TRU waste composition by disintegration

International Nuclear Information System (INIS)

Kuramoto, Ken-ichi; Banba, Tsunetaka; Mitamura, Hisayoshi; Sakai, Etsuro; Uno, Masayoshi; Kinoshita, H.; Yamanaka, Shinsuke

1999-01-01

In this study, the stability of YSZ waste forms for secular change of partitioned TRU waste composition by disintegration, one of important terms in long-term stability, is the special concern. Designed amount of waste and YSZ powder were mixed and sintered. These TRU waste forms were submitted to tests of phase stability, chemical durability, mechanical property and compactness. The results were compared with those of another YSZ waste forms, non-radioactive Ce and/or Nd doped YSZ samples, and glass and Synroc waste forms. Experimental results show following: (1) Phase stability of (Np+Am)-, (Np+U)-, and (Np+U+Bi)-doped YSZ waste forms could be maintained of that of the initial Np+Am-doped YSZ waste form permanently even when the composition of partitioned TRU waste were changed by disintegration. (2) Secular change also accelerated volume increase of YSZ waste forms as well as alpha-decay damage. (3) Hv, E and K IC of (Np+U)- and (Np+U+Bi)-doped YSZ waste forms were independent of the secular change of the partitioned TRU waste composition by disintegration. (4) Mechanical properties of YSZ waste forms were more than those of a glass and Synroc waste forms. (5) Compactness of YSZ waste forms was good as waste forms for the partitioned TRU wastes. (J.P.N.)

A facility design for repackaging ORNL CH-TRU legacy waste in Building 3525

International Nuclear Information System (INIS)

Huxford, T.J.; Cooper, R.H. Jr.; Davis, L.E.; Fuller, A.B.; Gabbard, W.A.; Smith, R.B.; Guay, K.P.; Smith, L.C.

1995-07-01

For the last 25 years, the Oak Ridge National Laboratory (ORNL) has conducted operations which have generated solid, contact-handled transuranic (CH-TRU) waste. At present the CH-TRU waste inventory at ORNL is about 3400 55-gal drums retrievably stored in RCRA-permitted, aboveground facilities. Of the 3400 drums, approximately 2600 drums will need to be repackaged. The current US Department of Energy (DOE) strategy for disposal of these drums is to transport them to the Waste Isolation Pilot Plant (WIPP) in New Mexico which only accepts TRU waste that meets a very specific set of criteria documented in the WIPP-WAC (waste acceptance criteria). This report describes activities that were performed from January 1994 to May 1995 associated with the design and preparation of an existing facility for repackaging and certifying some or all of the CH-TRU drums at ORNL to meet the WIPP-WAC. For this study, the Irradiated Fuel Examination Laboratory (IFEL) in Building 3525 was selected as the reference facility for modification. These design activities were terminated in May 1995 as more attractive options for CH-TRU waste repackaging were considered to be available. As a result, this document serves as a final report of those design activities

Vertical profiles of 239(240)Pu, 238Pu and 241Am in some peculiar Italian mosses

International Nuclear Information System (INIS)

Testa, C.; Desideri, D.; Guerra, F.; Meli, M.A.; Roselli, C.; Jia, G.; Degetto, S.

2000-01-01

During the last two years the Urbino University and the Padua ICTIMA CNR were working on a special radioecological program having the aim to study the Pu and Am retention behaviour in different species of mosses growing in two Italian regions (Urbino, Central Italy, 450 m a.s.l. and Alps region, Northern Italy, 1500 m a.s.l.). 239,240 Pu, 238 Pu and 241 Am were separated and determined by extraction chromatography, electroplating and alpha spectrometry; 242 Pu and 243 Am were used as the yield tracers. The paper summarizes the results dealing with the vertical profiles of the radionuclides in three different species of mosses. Several 1-2 cm high sections were obtained and dated by 210 Pb determination. Typical concentration peaks for Pu and Am were found for very old moss species ('Sphagnum Compactum' and 'Sphagnum Nemoreum') at a depth corresponding to the early 1960's which is the period characterized by the maximum nuclear weapon tests. In more recent moss species ('Neckeria Crispa') no peak was observed and the regression curves showed that Am is more mobile than Pu. (author)

The WIPP RCRA Part B permit application for TRU mixed waste disposal

International Nuclear Information System (INIS)

Johnson, J.E.

1995-01-01

In August 1993, the New Mexico Environment Department (NMED) issued a draft permit for the Waste Isolation Pilot Plant (WIPP) to begin experiments with transuranic (TRU) mixed waste. Subsequently, the Department of Energy (DOE) decided to cancel the on-site test program, opting instead for laboratory testing. The Secretary of the NMED withdrew the draft permit in 1994, ordering the State's Hazardous and Radioactive Waste Bureau to work with the DOE on submittal of a revised permit application. Revision 5 of the WIPP's Resource Conservation and Recovery Act (RCRA) Part B Permit Application was submitted to the NMED in May 1995, focusing on disposal of 175,600 m 3 of TRU mixed waste over a 25 year span plus ten years for closure. A key portion of the application, the Waste Analysis Plan, shifted from requirements to characterize a relatively small volume of TRU mixed waste for on-site experiments, to describing a complete program that would apply to all DOE TRU waste generating facilities and meet the appropriate RCRA regulations. Waste characterization will be conducted on a waste stream basis, fitting into three broad categories: (1) homogeneous solids, (2) soil/gravel, and (3) debris wastes. Techniques used include radiography, visually examining waste from opened containers, radioassay, headspace gas sampling, physical sampling and analysis of homogeneous wastes, and review of documented acceptable knowledge. Acceptable knowledge of the original organics and metals used, and the operations that generated these waste streams is sufficient in most cases to determine if the waste has toxicity characteristics, hazardous constituents, polychlorinated biphenyls (PBCs), or RCRA regulated metals

The evaluation of the mass distribution data for 238U, 239Pu and 242Pu fission

International Nuclear Information System (INIS)

Liu Tingjin

2002-01-01

The mass distribution data for 238 U at E n =1.5, 5.5, 8.3, 11.3, 14.9, 22.0, 27.5, 50.0, 99.5, 160.0 MeV, E p =20.0, 60.0 MeV 239 Pu at E n =0.17, 7.9, 14.5 MeV and 242 Pu at E n =15.1 MeV were evaluated and recommended based on the main available experimental data up to now. The experimental data were make necessary corrections and their errors were also made necessary adjustments. The problems concerned were discussed

Gas generation from radiolytic attack of TRU-contaminated hydrogenous waste

International Nuclear Information System (INIS)

Zerwekh, A.

1979-06-01

In 1970, the Waste Management and Transportation Division of the Atomic Energy Commission ordered a segregation of transuranic (TRU)-contaminated solid wastes. Those below a contamination level of 10 nCi/g could still be buried; those above had to be stored retrievably for 20 y. The possibility that alpha-radiolysis of hydrogenous materials might produce toxic, corrosive, and flammable gases in retrievably stored waste prompted an investigation of gas identities and generation rates in the laboratory and field. Typical waste mixtures were synthesized and contaminated for laboratory experiments, and drums of actual TRU-contaminated waste were instrumented for field testing. Several levels of contamination were studied, as well as pressure, temperature, and moisture effects. G (gas) values were determined for various waste matrices, and degradation products were examined

Direct fabrication of 238PuO2 fuel forms

International Nuclear Information System (INIS)

Burney, G.A.; Congdon, J.W.

1982-07-01

The current process for the fabrication of 238 PuO 2 heat sources includes precipitation of small particle plutonium oxalate crystals (4 to 6 μm diameter), a calcination to PuO 2 , ball milling, cold pressing, granulation (60 to 125 μm), and granule sintering prior to hot pressing the fuel pellet. A new two-step direct-strike Pu(III) oxalate precipitation method which yields mainly large well-developed rosettes (50 to 100 μm diameter) has been demonstrated in the laboratory and in the plant. These large rosettes are formed by agglomeration of small (2 to 4 μm) crystals, and after calcining and sintering, were directly hot pressed into fuel forms, thus eliminating several of the powder conditioning steps. Conditions for direct hot pressing of the large heat-treated rosettes were determined and a full-scale General Purpose Heat Source pellet was fabricated. The pellet had the desired granule-type microstructure to provide dimensional stability at high temperature. 27 figures

Bone tumors induced by inhalation of 238PuO2 in dogs

International Nuclear Information System (INIS)

Park, J.F.; Lund, J.E.; Ragan, H.A.; Hackett, P.L.; Frazier, M.E.

1976-01-01

Plutonium-238, an alpha-emitting radionuclide, is used as a heat source in thermoelectric power generators such as have been employed on lunar expeditions of communications satellites and in cardiac pacemakers. It has an 86.4 year half-life and emits 5.5 MeV alpha particles. Beagle dogs were given single 10 to 30 minute exposures to 238 PuO 2 aerosols to study the long-term translocation of plutonium and biologicl effects. Dogs with a terminal body burden ranging from 7 to 260 MuCi were euthanized due to respiratory insufficiency related to plutonium-induced pneumonitis during the first 3 years after exposure. Nine of the 11 dogs euthanized during the 4 to 6 year postexposure period had osteosarcomas. The terminal plutonium body burden in the tumor-bearing dogs ranged from 0.5 to 2.6 muCi with 30 to 55 percent of the plutonium in the skeleton. Experiments are in progress to further define the dose-effect relationship of inhaled 238 PuO 2 and investigate the mechanisms of plutonium-induced neoplasia

Study on characteristics of spent PWR cladding hull for categorizing into Non-TRU waste

International Nuclear Information System (INIS)

Jung, In Ha; Kim, Jong Ho; Park, Jang Jin; Shin, Jin Myeong; Lee, Ho Hee; Yang, Myung Seung

2005-01-01

AFCI and GEN-IV programs aim for decreasing the high level radioactive wastes to be disposed. They also try to get valuable materials to recycle as resources such as uranium and plutonium. On the other hand, cladding hull expected to be one-thirds in volume of spent fuel assembly has not studied so much in the point view of recycling to reuse. Since traditional process of reprocessing was wet process, cladding hull generating through the reprocessing process was unavoidably contaminated with TRU by acid solvent during the process. Therefore, cladding hull has been classified into TRU wastes or high level wastes. According to the strategy for TRU high level radioactive wastes of USA as well as Korea, it regulates in two respects. One is activity and the other is heat generation. In respect of activity, TRU waste contains more than 100 nCi/kg of alpha emits with longer half life than 20 years and higher than 92 in atomic number. Also, wastes are categorized into TRU waste when it generates higher than 2kW/m3, in the respect of heat generation. Our results as well as literatures, almost all of TRU nuclides in the cladding hull are responsible for remained uranium and plutonium owing to pellet-cladding interaction. In addition, recoiled fission products on the surface of the cladding hull serve as heat generator. Up to now, decontamination of the cladding hull generating from the reprocessing of wet process is regarded as valueless and un-economic works owing to the amount of second waste produced

Basic study on decontamination of TRU wastes with cerium mediated electrolytic oxidation method

International Nuclear Information System (INIS)

Ishii, Junichi; Kobayashi, Fuyumi; Uchida, Shoji; Sumiya, Masato; Kida, Takashi; Shirahashi, Koichi; Umeda, Miki; Sakuraba, Koichi

2010-03-01

At Nuclear Fuel Cycle Safety Engineering Research Facility (NUCEF), the cerium mediated electrolytic oxidation method which is a decontamination technique to decrease the radioactivity of TRU wastes to the clearance-level has been developed for the effective reduction of TRU wastes generated from the decommissioning of a nuclear fuel reprocessing facility and so on. This method corrodes the oxide layer and the surface of metallic TRU metal wastes by the strong oxidation power of Ce 4+ in nitric acid. In this study, parameter tests were conducted to optimize the solution condition of Ce 3+ initial concentrations and nitric acid concentrations. The target corrosion rate of metallic TRU wastes set to be 2 - 4 μm/h for the practical use of this method. Under the optimized solution condition, a dissolution test of stainless steel simulating wastes was carried out. From the result of the dissolution test, the average corrosion rate was 3.3 μm/h during the test time of 90 hours. Based on the supposition that the corrosion depth of metallic TRU wastes was 20 μm enough to achieve the clearance-level, the treatment time for the decontamination was about 6 hours. It was confirmed from the result that the decontamination could be performed within one day and the decontamination solution could repeatedly reuse 15 times. (author)

Field study of the migration of 237Np, 238Pu and 241Am in a weak loess aquifer

International Nuclear Information System (INIS)

Liu, C.L.; Wang, Z.M.; Li, S.S.; Yang, Y.E.; Li, B.; Jiang, H.; Jiang, L.; Wang, L.; Li, D.

2004-01-01

The migration of 237 Np, 238 Pu and 241 Am in a weak loess aquifer was investigated in-situ in an Underground Research Facility. Quartz containing 237 Np, 238 Pu, 241 Am and 3 H was introduced into the aquifer with a stainless steel tube. The local water flow in the aquifer was monitored using a 3-dimensional sampling system. The contaminated area of the aquifer was obtained wholly with the help of a pre-installed stainless steel frame and cut into small pieces (samples) 3-dimensionally and analyzed. 3 H in the water samples was determined with a liquid scintillation analyzer (Tri-Camb 2250). Radioactivity of 237 Np and 241 Am in the soil samples were determined with a low energy photon detector (HPGe), 238 Pu was analyzed with a low background αandβ detector after chemical separation. The result of the 3-year experiment indicated that 237 Np, 238 Pu and 241 Am were strongly absorbed by the loess aquifer. The retardation factor of 237 Np in the loess aquifer was 1.54 x 10 4 . (author)

Estimation of uncertainties in resonance parameters of {sup 56}Fe, {sup 239}Pu, {sup 240}Pu and {sup 238}U

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, Tsuneo; Shibata, Keiichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-05-01

Uncertainties have been estimated for the resonance parameters of {sup 56}Fe, {sup 239}Pu, {sup 240}Pu and {sup 238}U contained in JENDL-3.2. Errors of the parameters were determined from the measurements which the evaluation was based on. The estimated errors have been compiled in the MF32 of the ENDF format. The numerical results are given in tables. (author)

Late effects of inhaled 238PuO2 in beagles

International Nuclear Information System (INIS)

Park, J.F.; Case, A.C.; Catt, D.L.; Hackett, P.L.; Lund, J.E.; Powers, G.J.; Ragan, H.A.; Watson, C.R.

1976-01-01

Osteosarcomas were the primary cause of death in beagle dogs 4 to 8 years after inhalation of 238 PuO 2 . The plutonium body burden at death ranged from 0.4 to 2.6 μCi with 32 to 55 percent of the plutonium in the skeleton. Pulmonary neoplasia was observed in three of the bone-tumor-bearing dogs

MCNP efficiency calculations of INEEL passive active neutron assay system for simulated TRU waste assays

International Nuclear Information System (INIS)

Yoon, W.Y.; Meachum, T.R.; Blackwood, L.G.; Harker, Y.D.

2000-01-01

The Idaho National Engineering and Environmental Laboratory Stored Waste Examination Pilot Plant (SWEPP) passive active neutron (PAN) radioassay system is used to certify transuranic (TRU) waste drums in terms of quantifying plutonium and other TRU element activities. Depending on the waste form involved, significant systematic and random errors need quantification in addition to the counting statistics. To determine the total uncertainty of the radioassay results, a statistical sampling and verification approach has been developed. In this approach, the total performance of the PAN nondestructive assay system is simulated using the computer models of the assay system, and the resultant output is compared with the known input to assess the total uncertainty. The supporting steps in performing the uncertainty analysis for the passive assay measurements in particular are as follows: (1) Create simulated waste drums and associated conditions; (2) Simulate measurements to determine the basic counting data that would be produced by the PAN assay system under the conditions specified; and (3) Apply the PAN assay system analysis algorithm to the set of counting data produced by simulating measurements to determine the measured plutonium mass. The validity of this simulation approach was verified by comparing simulated output against results from actual measurements using known plutonium sources and surrogate waste drums. The computer simulation of the PAN system performance uses the Monte Carlo N-Particle (MCNP) Code System to produce a neutron transport calculation for a simulated waste drum. Specifically, the passive system uses the neutron coincidence counting technique, utilizing the spontaneous fission of 240 Pu. MCNP application to the SWEPP PAN assay system uncertainty analysis has been very useful for a variety of waste types contained in 208-ell drums measured by a passive radioassay system. The application of MCNP to the active radioassay system is also feasible

The AS-76 interlaboratory experiment on the alpha spectrometric determinaion of Pu-238. Part 3: Preparation and characterization of samples

International Nuclear Information System (INIS)

Bortels, G.; Broothaerts, J.; Bievre, P. de

1980-01-01

Four plutonium samples containing 0.2, 0.8, 1.6 and 0.9 atom % of 238 Pu have been prepared for the Interlaboratory Experiment AS-76. Of these three were input solutions from a reprocessing plant. The fourth sample was from a plutonium product solution. These samples have been characterized by two alpha spectrometry laboratories and two mass spectrometry laboratories to certify the ratio of alpha activities 238 Pu/( 239 Pu + 240 Pu) and the isotopic composition, respectively

Thermal processing systems for TRU mixed waste

International Nuclear Information System (INIS)

Eddy, T.L.; Raivo, B.D.; Anderson, G.L.

1992-01-01

This paper presents preliminary ex situ thermal processing system concepts and related processing considerations for remediation of transuranic (TRU)-contaminated wastes (TRUW) buried at the Radioactive Waste Management Complex (RWMC) of the Idaho National Engineering Laboratory (INEL). Anticipated waste stream components and problems are considered. Thermal processing conditions required to obtain a high-integrity, low-leachability glass/ceramic final waste form are considered. Five practical thermal process system designs are compared. Thermal processing of mixed waste and soils with essentially no presorting and using incineration followed by high temperature melting is recommended. Applied research and development necessary for demonstration is also recommended

The effect of vibration on alpha radiolysis of transuranic (TRU) waste

International Nuclear Information System (INIS)

Zerwekh, A.; Kosiewicz, S.; Warren, J.

1993-01-01

This paper reports on previously unpublished scoping work related to the potential for vibration to redistribute radionuclides on transuranic (TRU) waste. If this were to happen, the amount of gases generated, including hydrogen, could be increased above the undisturbed levels. This could be an important consideration for transport of TRU wastes either at DOE sites or from them to a future repository, e.g., the Waste Isolation Pilot Plant (WIPP). These preliminary data on drums of real waste seem to suggest that radionuclide redistribution does not occur. However improvements in the experimental methodology are suggested to enhance safety of future experiments on real wastes as well as to provide more rigorous data

CONCRETE CONTAINERS FOR LONG TERM STORAGE AND FINAL DISPOSAL OF TRU WASTE AND LONG LIVED ILW

International Nuclear Information System (INIS)

Sakamoto, H.; Asano, H.; Tunaboylu, K.; Mayer, G.; Klubertanz, G.; Kobayashi, S.; Komuro, T.; Wagner, E.

2003-01-01

Transuranic (TRU) waste packaging development has been conducted since 1998 by the Radioactive Waste Management Funding and Research Centre (RWMC) to support the TRU waste disposal concept in Japan. In this paper, the overview of development status of the reinforced concrete package is introduced. This package has been developed in order to satisfy the Japanese TRU waste disposal concept based on current technology and to provide a low cost package. Since 1998, the basic design work (safety evaluation, manufacturing and handling procedure, economic evaluation, elemental tests etc.) have been carried out. As a result, the basic specification of the package was decided. This report presents the concept as well as the results of basic design, focused on safety analysis and handling procedure of the package. Two types of the packages exist: - Package-A: for non-heat generating TRU waste from reprocessing in 200 l drums and - Package-B: for heat generating TRU-waste from reprocessing

DEVELOPMENT OF THE TRU WASTE TRANSPORTATION FLEET--A SUCCESS STORY

International Nuclear Information System (INIS)

Devarakonda, Murthy; Morrison, Cindy; Brown, Mike

2003-01-01

Since March 1999, the Waste Isolation Pilot Plant (WIPP), located in southeastern New Mexico, has been operated by the U.S. Department of Energy (DOE), Carlsbad Field Office (CBFO), as a repository for the permanent disposal of defense-related transuranic (TRU) waste. More than 1,450 shipments of TRU waste for WIPP disposal have been completed, and the WIPP is currently receiving 12 to 16 shipments per week from five DOE sites around the nation. One of the largest fleets of Type B packagings supports the transportation of TRU waste to WIPP. This paper discusses the development of this fleet since the original Certificate of Compliance (C of C) for the Transuranic Package Transporter-II (TRUPACT-II) was issued by the U.S. Nuclear Regulatory Commission (NRC) in 1989. Evolving site programs, closure schedules of major sites, and the TRU waste inventory at the various DOE sites have directed the sizing and packaging mix of this fleet. This paper discusses the key issues that guided this fleet development, including the following: While the average weight of a 55-gallon drum packaging debris could be less than 300 pounds (lbs.), drums containing sludge waste or compacted waste could approach the maximum allowable weight of 1,000 lbs. A TRUPACT-II shipment may consist of three TRUPACT-II packages, each of which is limited to a total weight of 19,250 lbs. Payload assembly weights dictated by ''as-built'' TRUPACT-II weights limit each drum to an average weight of 312 lbs when three TRUPACT-IIs are shipped. To optimize the shipment of heavier drums, the HalfPACT packaging was designed as a shorter and lighter version of the TRUPACT-II to accommodate a heavier load. Additional packaging concepts are currently under development, including the ''TRUPACT-III'' packaging being designed to address ''oversized'' boxes that are currently not shippable in the TRUPACT-II or HalfPACT due to size constraints. Shipment optimization is applicable not only to the addition of new

Beta decay heat following U-235, U-238 and Pu-239 neutron fission

Science.gov (United States)

Li, Shengjie

1997-09-01

This is an experimental study of beta-particle decay heat from 235U, 239Pu and 238U aggregate fission products over delay times 0.4-40,000 seconds. The experimental results below 2s for 235U and 239Pu, and below 20s for 238U, are the first such results reported. The experiments were conducted at the UMASS Lowell 5.5-MV Van de Graaff accelerator and 1-MW swimming-pool research reactor. Thermalized neutrons from the 7Li(p,n)7Be reaction induced fission in 238U and 239Pu, and fast neutrons produced in the reactor initiated fission in 238U. A helium-jet/tape-transport system rapidly transferred fission fragments from a fission chamber to a low background counting area. Delay times after fission were selected by varying the tape speed or the position of the spray point relative to the beta spectrometer that employed a thin-scintillator-disk gating technique to separate beta-particles from accompanying gamma-rays. Beta and gamma sources were both used in energy calibration. Based on low-energy(energies 0-10 MeV. Measured beta spectra were unfolded for their energy distributions by the program FERD, and then compared to other measurements and summation calculations based on ENDF/B-VI fission-product data performed on the LANL Cray computer. Measurements of the beta activity as a function of decay time furnished a relative normalization. Results for the beta decay heat are presented and compared with other experimental data and the summation calculations.

TRU-ART: A cost-effective prototypical neutron imaging technique for transuranic waste certification systems

International Nuclear Information System (INIS)

Horton, W.S.

1989-01-01

The certification of defense radioactive waste as either transuranic or low-level waste requires very sensitive and accurate assay instrumentation to determine the specific radioactivity within an individual waste package. An assay instrument that employs a new technique (TRU-ART), which can identify the location of the radioactive material within a waste package, was designed, fabricated, and tested to potentially enhance the certification of problem defense waste drums. In addition, the assay instrumentation has potential application in radioactive waste reprocessing and neutron tomography. The assay instrumentation uses optimized electronic signal responses from an array of boral- and cadmium-shielded polyethylene-moderated 3 H detector packages. Normally, thermal neutrons that are detected by 3 H detectors have very poor spatial dependency that may be used to determine the location of the radioactive material. However, these shielded-detector packages of the TRU-ART system maintain the spatial dependency of the radioactive material in that the point of fast neutron thermalization is immediately adjacent to the 3 H detector. The TRU-ART was used to determine the location of radioactive material within three mock-up drums (empty, peat moss, and concrete) and four actual waste drums. The TRU-ART technique is very analogous to emission tomography. The mock-up drum and actual waste drum data, which were collected by the TRU-ART, were directly input into a algebraic reconstruction code to produce three-dimensional isoplots. Finally, a comprehensive fabrication cost estimate of the fielded drum assay system and the TRU-ART system was determined, and, subsequently, these estimates were used in a cost-benefit analysis to compare the economic advantage of the respective systems

A study of accelerated radiation damage effects in PuO{sub 2} and gadolinia-stabilized cubic zirconia, Zr{sub 0.79}Gd{sub 0.14}Pu{sub 0.07}O{sub 1.93}, doped with {sup 238}Pu

Energy Technology Data Exchange (ETDEWEB)

Burakov, B.E., E-mail: burakov@peterlink.ru [V.G. Khlopin Radium Institute, 28, 2-nd Murinskiy Ave., St. Petersburg, 194021 (Russian Federation); Yagovkina, M.A. [A.F. Ioffe Physical-Technical Institute, 26, Politekhnicheskaya, St. Petersburg, 194021 (Russian Federation)

2015-12-15

Polycrystalline samples of cubic zirconia, Zr{sub 0.79}Gd{sub 0.14}Pu{sub 0.07}O{sub 1.93}, doped with approximately 9.9 wt.% {sup 238}Pu, and PuO{sub 2} containing 11.0 wt. % {sup 238}Pu (and main isotope is {sup 239}Pu) have been repeatedly studied during many years by X-ray diffraction analysis. At a temperature of 25 °C the unit-cell parameter of PuO{sub 2} increases depending on accumulated dose, and is accompanied by decrease of coherent scattering region (CSR). Self-irradiation of Zr{sub 0.79}Gd{sub 0.14}Pu{sub 0.07}O{sub 1.93} is accompanied with repeated change of unit-cell parameter and CSR.

Development of an Alternative Treatment Scheme for Sr/TRU Removal: Permanganate Treatment of AN-107 Waste

International Nuclear Information System (INIS)

Hallen, R.T.; Bryan, S.A.; Hoopes, F.V.

2000-01-01

A number of Hanford tanks received waste containing organic complexants, which increase the volubility of Sr-90 and transuranic (TRU) elements. Wastes from these tanks require additional pretreatment to remove Sr-90 and TRU for immobilization as low activity waste (Waste Envelope C). The baseline pretreatment process for Sr/TRU removal was isotopic exchange and precipitation with added strontium and iron. However, studies at both Battelle and Savannah River Technology Center (SRTC) have shown that the Sr/Fe precipitates were very difficult to filter. This was a result of the formation of poor filtering iron solids. An alternate treatment technology was needed for Sr/TRU removal. Battelle had demonstrated that permanganate treatment was effective for decontaminating waste samples from Hanford Tank SY-101 and proposed that permanganate be examined as an alternative Sr/TRU removal scheme for complexant-containing tank wastes such as AW107. Battelle conducted preliminary small-scale experiments to determine the effectiveness of permanganate treatment with AN-107 waste samples that had been archived at Battelle from earlier studies. Three series of experiments were performed to evaluate conditions that provided adequate Sr/TRU decontamination using permanganate treatment. The final series included experiments with actual AN-107 diluted feed that had been obtained specifically for BNFL process testing. Conditions that provided adequate Sr/TRU decontamination were identified. A free hydroxide concentration of 0.5M provided adequate decontamination with added Sr of 0.05M and permanganate of 0.03M for archived AN-107. The best results were obtained when reagents were added in the sequence Sr followed by permanganate with the waste at ambient temperature. The reaction conditions for Sr/TRU removal will be further evaluated with a 1-L batch of archived AN-107, which will provide a large enough volume of waste to conduct crossflow filtration studies (Hallen et al. 2000a)

Development of an Alternative Treatment Scheme for Sr/TRU Removal: Permanganate Treatment of AN-107 Waste

Energy Technology Data Exchange (ETDEWEB)

RT Hallen; SA Bryan; FV Hoopes

2000-08-04

A number of Hanford tanks received waste containing organic complexants, which increase the volubility of Sr-90 and transuranic (TRU) elements. Wastes from these tanks require additional pretreatment to remove Sr-90 and TRU for immobilization as low activity waste (Waste Envelope C). The baseline pretreatment process for Sr/TRU removal was isotopic exchange and precipitation with added strontium and iron. However, studies at both Battelle and Savannah River Technology Center (SRTC) have shown that the Sr/Fe precipitates were very difficult to filter. This was a result of the formation of poor filtering iron solids. An alternate treatment technology was needed for Sr/TRU removal. Battelle had demonstrated that permanganate treatment was effective for decontaminating waste samples from Hanford Tank SY-101 and proposed that permanganate be examined as an alternative Sr/TRU removal scheme for complexant-containing tank wastes such as AW107. Battelle conducted preliminary small-scale experiments to determine the effectiveness of permanganate treatment with AN-107 waste samples that had been archived at Battelle from earlier studies. Three series of experiments were performed to evaluate conditions that provided adequate Sr/TRU decontamination using permanganate treatment. The final series included experiments with actual AN-107 diluted feed that had been obtained specifically for BNFL process testing. Conditions that provided adequate Sr/TRU decontamination were identified. A free hydroxide concentration of 0.5M provided adequate decontamination with added Sr of 0.05M and permanganate of 0.03M for archived AN-107. The best results were obtained when reagents were added in the sequence Sr followed by permanganate with the waste at ambient temperature. The reaction conditions for Sr/TRU removal will be further evaluated with a 1-L batch of archived AN-107, which will provide a large enough volume of waste to conduct crossflow filtration studies (Hallen et al. 2000a).

Research and development for treatment and disposal technologies of TRU waste

International Nuclear Information System (INIS)

Kamei, Gento; Honda, Akira; Mihara, Morihiro; Oda, Chie; Murakami, Hiroshi; Masuda, Kenta; Yamaguchi, Kohei; Nakanishi, Hiroshi; Sasaki, Ryoichi; Ichige, Satoru; Takahashi, Kuniaki; Meguro, Yoshihiro; Yamaguchi, Hiromi; Aoyama, Yoshio

2007-09-01

After the publication of the 2nd progress report of geological disposal of TRU waste in Japan, policy and general scheme of future study for the waste disposal in Japan was published by ANRE and JAEA. This annual report summarized aim and progress of individual problem, which was assigned into JAEA in the published policy and general scheme. The problems are as follows; characteristics of TRU waste and its geologic disposal, treatment and waste production, quality control and inspection methodology for waste, mechanical analysis of near-field, data acquisition and preparation on radionuclides migration, cementitious material transition, bentonite and rock alteration in alkaline solution, nitrate effect, performance assessment of the disposal system and decomposition of nitrate as an alternative technology. (author)

Design improvements for gloveboxes used [in] {sup 238}PuO{sub 2} process operations

Energy Technology Data Exchange (ETDEWEB)

George, T.G. [Los Alamos National Lab., NM (United States). Nuclear Materials Technology Div.

1997-09-01

{sup 238}PuO{sub 2} process operations are housed in a complex of 76 gloveboxes and introductory hoods connected by means of an overhead trolley housed in a tunnel. Because a significant number of the gloveboxes used for {sup 238}PuO{sub 2} processing were installed before the original startup of the facility in 1978, they have been in service for nearly 20 years. During a recent heat source production campaign, numerous contamination releases in the {sup 238}PuO{sub 2} processing area were traced to degraded elastomer gaskets used for glovebox connections, and attachment of feed-throughs, service panels, and windows. Evaluation of the degraded gaskets revealed that a combination of radiolytic degradation related to the high specific activity of {sup 238}Pu, and extended service at high altitude in a low (to extremely low) humidity environment had resulted in accelerated gasket aging. However, it was also apparent that gasket design was the most important factor in actual contamination release. All of the contamination releases that were traced to degraded gaskets occurred in variations of a design that used a spline to expand an elastomeric gasket into the space between a connecting flange, window, or service panel, and a glovebox opening. No contamination releases were traced to the gasket design that employed bolted clamps to compress the gasket between a connecting flange, window, or panel, and the exterior surface of a glovebox opening. As a result of these findings, the Actinide Ceramics group at LANL (NMT-9) has initiated a routine replacement and upgrade program to replace aging gloveboxes. All of the new gloveboxes will utilize the preferred gasket design, which is expected to reduce the number and frequency of contamination releases.

Progress report on disposal concept for TRU waste in Japan

International Nuclear Information System (INIS)

2000-03-01

The object of this report is to contribute towards establishing a national TRU waste disposal program by integrating the results of research and development work carried out by JNC and the electricity utilities and summarizing the findings concerning safe methods for TRU waste disposal. The report consists of 5 chapters: the first describes the boundary conditions for the review of the TRU waste disposal concept (including geological conditions) and the basic concept adopted; the second describes the generation and characteristics of TRU waste and the third outlines the disposal technology; the fourth gives the key of the safety assessment and the fifth presents the conclusions of the report and lists issues for future consideration. The geological environment of Japan is simply classified into crystalline and sedimentary rock types (in terms of groundwater flow properties and rock strength) and a set of target conditions/properties for each rock type is then established. Based on this, a case which represents the basis for performance assessment (the reference case) will be defined. Alternatives to the reference case are studied to investigate the flexibility of the disposal concept. Under the conditions assumed in this study, the perturbing events considered showed no significant effects on the dose at the 100 meter evaluation point, owing to the relatively high efficiency of the natural barrier. However, the significant effect of these events on nuclide from the EBS shows that, in the case of a less efficient natural barrier, their effects could influence resulting dose. (S.Y.)

/sup 238/Pu fuel form processes quarterly report, April-June 1980

Energy Technology Data Exchange (ETDEWEB)

Folger, R. L.

1980-06-01

Savannah River Laboratory (SRL) completed the development of a production process to fabricate /sup 238/PuO/sub 2/ fuel forms for the GPHS. The fabrication flowsheet was based on a flowsheet originally developed at Los Alamos National Scientific Laboratory (LANSL). A summary report of the SRL process development effort is presented.

Feasibility analysis of constant TRU feeding in waste transmutation system using accelerator-driven subcritical system

Energy Technology Data Exchange (ETDEWEB)

Lee, Kun Jai; Cho, Nam Zin; Jo, Chang Keun; Park, Chang Je; Kim, Do Sam; Park, Jeong Hwan [Korea Advanced Institute of Science and Technology, Taejon (Korea)

1999-03-01

It is probable that the issue of nuclear spent fuel and high-level waste can have negative impact on the future expansion of nuclear power programs. Accelerator-driven nuclear waste transmutation with constant composition TRU feeding which satisfies non-proliferation condition will help establish the long-range nuclear waste disposal strategy. In this study, current status of accelerator-driven transmutation of waste technology, and feasibility analysis of constant composition TRU feeding system were investigated. We ascertained that solid system using constant composition TRU is feasible with the the capability of transmutation. (author). 13 refs., 53 figs., 20 tabs.

Device Assembly Facility (DAF) Glovebox Radioactive Waste Characterization

International Nuclear Information System (INIS)

Dominick, J L

2001-01-01

The Device Assembly Facility (DAF) at the Nevada Test Site (NTS) provides programmatic support to the Joint Actinide Shock Physics Experimental Research (JASPER) Facility in the form of target assembly. The target assembly activities are performed in a glovebox at DAF and include Special Nuclear Material (SNM). Currently, only activities with transuranic SNM are anticipated. Preliminary discussions with facility personnel indicate that primarily two distributions of SNM will be used: Weapons Grade Plutonium (WG-Pu), and Pu-238 enhanced WG-Pu. Nominal radionuclide distributions for the two material types are included in attachment 1. Wastes generated inside glove boxes is expected to be Transuranic (TRU) Waste which will eventually be disposed of at the Waste Isolation Pilot Plant (WIPP). Wastes generated in the Radioactive Material Area (RMA), outside of the glove box is presumed to be low level waste (LLW) which is destined for disposal at the NTS. The process knowledge quantification methods identified herein may be applied to waste generated anywhere within or around the DAF and possibly JASPER as long as the fundamental waste stream boundaries are adhered to as outlined below. The method is suitable for quantification of waste which can be directly surveyed with the Blue Alpha meter or swiped. An additional quantification methodology which requires the use of a high resolution gamma spectroscopy unit is also included and relies on the predetermined radionuclide distribution and utilizes scaling to measured nuclides for quantification

Gas generation and migration analysis for TRU waste disposal system

International Nuclear Information System (INIS)

Ando, Kenichi; Noda, Masaru; Yamamoto, Mikihiko; Mihara, Morihiro

2005-09-01

In TRU waste disposal system, significant quantities of gases may be generated due to metal corrosion, radiolysis effect and microorganism activities. It is therefore recommended that the potential impact of gas generation and migration on TRU waste repository should be evaluated. In this study, gas generation rates were calculated in the repository and gas migration analysis in the disposal system were carried out using two phase flow model with results of gas generation rates. First, the time dependencies of gas generation rate in each TRU waste repositories were evaluated based on amounts of metal, organic matter and radioactivity. Next, the accumulation pressure of gases and expelled pore water volume nuclides in the repository were calculated by TOUGH2 code. After that, the results showed that the increase of gas pressure was the range of 1.3 to 1.4 MPa. In the repository with and without buffer, the rate of expelled pore water was 0.006 - 0.009 m 3 /y and 0.018 - 0.24m 3 /y, respectively. In addition, the radioactive gas migration through the repository and geosphere are evaluated. And re-saturation analysis is also performed to evaluate the initial condition of the system. (author)

TRU decontamination of high-level Purex waste by solvent extraction using a mixed octyl(phenyl)-N,N-diisobutyl-carbamoylmethylphosphine oxide/TBP/NPH (TRUEX) solvent

International Nuclear Information System (INIS)

Horwitz, E.P.; Kalina, D.G.; Diamond, H.; Kaplan, L.; Vandegrift, G.F.; Leonard, R.A.; Steindler, M.J.; Schulz, W.W.

1984-01-01

The TRUEX (transuranium extraction) process was tested on a simulated high-level dissolved sludge waste (DSW). A batch counter-current extraction mode was used for seven extraction and three scrub stages. One additional extraction stage and two scrub stages and all strip stages were performed by batch extraction. The TRUEX solvent consisted of 0.20 M octyl(phenyl)-N,N-diisobutylcarbamoyl-methylphosphine oxide-1.4 M TBP in Conoco (C 12 -C 14 ). The feed solution was 1.0 M in HNO 3 , 0.3 M in H 2 C 2 O 4 and contained mixed (stable) fission products, U, Np, Pu, and Am, and a number of inert constituents, e.g., Fe and Al. The test showed that the process is capable of reducing the TRU concentration in the DSW by a factor of 4 x 10 4 (to <100 nCi/g of disposed form) and reducing the quantity of TRU waste by two orders of magnitude

A preliminary evaluation of certain NDA techniques for RH-TRU characterization

Energy Technology Data Exchange (ETDEWEB)

Hartwell, J.K.; Yoon, W.Y.; Peterson, H.K. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

1997-11-01

This report presents the results of modeling efforts to evaluate selected NDA assay methods for RH-TRU waste characterization. The target waste stream was Content Code 104/107 113-liter waste drums that comprise the majority of the INEL`s RH-TRU waste inventory. Two NDA techniques are treated in detail. One primary NDA technique examined is gamma-ray spectrometry to determine the drum fission and activation product content, and fuel sample inventory calculations using the ORIGEN code to predict the total drum inventory. A heavily shielded and strongly collimated HPGe spectrometer system was designed using MCNP modeling. Detection limits and expected precision of this approach were estimated by a combination of Monte Carlo modeling and synthetic gamma-ray spectrum generation. This technique may allow the radionuclide content of these wastes to be determined with relative standard deviations of 20 to 50% depending on the drum matrix and radionuclide. The INEL Passive/Active Neutron (PAN) assay system is the second primary technique considered. A shielded overpack for the 113-liter CC104/107 RH-TRU drums was designed to shield the PAN detectors from excessive gamma radiation. MCNP modeling suggests PAN detection limits of about 0.06 g {sup 235}U and 0.04 g {sup 239}Pu during active assays. 12 refs., 2 figs., 6 tabs.

Evaluation of fission cross sections and covariances for {sup 233}U, {sup 235}U, {sup 238}U, {sup 239}Pu, {sup 240}Pu, and {sup 241}Pu

Energy Technology Data Exchange (ETDEWEB)

Kawano, Toshihiko [Kyushu Univ., Fukuoka (Japan); Matsunobu, Hiroyuki [Data Engineering, Inc. (Japan); Murata, Toru [AITEL Corporation, Tokyo (JP)] [and others

2000-02-01

A simultaneous evaluation code SOK (Simultaneous evaluation on KALMAN) has been developed, which is a least-squares fitting program to absolute and relative measurements. The SOK code was employed to evaluate the fission cross sections of {sup 233}U, {sup 235}U, {sup 238}U, {sup 239}Pu, {sup 240}Pu, and {sup 241}Pu for the evaluated nuclear data library JENDL-3.3. Procedures of the simultaneous evaluation and the experimental database of the fission cross sections are described. The fission cross sections obtained were compared with evaluated values given in JENDL-3.2 and ENDF/B-VI. (author)

The TRUEX [TRansUranium EXtraction] process and the management of liquid TRU [transuranic] waste

International Nuclear Information System (INIS)

Schulz, W.W.; Horwitz, E.P.

1987-01-01

The TRUEX process is a new generic liquid-liquid extraction process for removal of all actinides from acidic nitrate or chloride nuclear waste solutions. Because of its high efficiency and great flexibility, the TRUEX process appears destined to be widely used in the US and possibly in other countries for cost-effective management and disposal of transuranic (TRU) wastes. In the US, TRU wastes are those that contain ≥3.7 x 10 6 Bq/kg) of TRU elements with half-lives greater than 20 y. This paper gives a brief review of the relevant chemistry and summarizes the current status of development and deployment of the TRUEX (TRansUranium EXtraction) process flowsheets to treat specific acidic waste solutions at several US Department of Energy sites. 19 refs., 4 figs., 4 tabs

TRU-waste decontamination and size reduction review, June 1983, US DOE/PNC technology exchange

International Nuclear Information System (INIS)

Becker, G.W. Jr.

1983-01-01

A review of transuranic (TRU) noncombustible waste decontamination and size reduction technology is presented. Electropolishing, vibratory cleaning, and spray decontamination processes developed at Battelle Pacific Northwest Laboratory (PNL) and Savannah River Laboratory (SRL) are highlighted. TRU waste size reduction processes at (PNL), Los Alamos National Laboratory (LANL), the Rocky Flats Plant (RFP), and SRL are also highlighted

Centralized processing of contact-handled TRU waste feasibility analysis

International Nuclear Information System (INIS)

1986-12-01

This report presents work for the feasibility study of central processing of contact-handled TRU waste. Discussion of scenarios, transportation options, summary of cost estimates, and institutional issues are a few of the subjects discussed

238Pu fuel form processes. Savannah River Laboratory monthly report

International Nuclear Information System (INIS)

1976-05-01

Progress in the Savannah River 238 Pu fuel form program is summarized. Suspended solids observed in the technical-grade oxalic acid solution used in H-Area B-Line had no significant effect on particle size or morphology. A small but significant increase in product purity was noted with the use of reagent-grade oxalic acid. The density of hot-pressed LCHP pellets made from both problem and standardized feed decreased with longer milling times as was observed for multi-hundred watt (MHW) pellets. The LCHP pellets (greater than 90 percent theoretical density) generally cracked following final heat treatment. Cold-pressing studies indicate the anticipated pressure variation during cold pressing in the PuFF facility will have negligible effect on the density of MHW spheres. Construction of the plutonium experimental facility is 72 percent complete

Determination of H2 Diffusion Rates through Various Closures on TRU Waste Bag-Out Bags

International Nuclear Information System (INIS)

Noll, Phillip D. Jr.; Callis, E. Larry; Norman, Kirsten M.

1999-01-01

The amount of H 2 diffusion through twist and tape (horse-tail), wire tie, plastic tie, and heat sealed closures on transuranic (TRU) waste bag-out bags has been determined. H 2 diffusion through wire and plastic tie closures on TRU waste bag-out bags has not been previously characterized and, as such, TRU waste drums containing bags with these closures cannot be certified and/or shipped to the Waste Isolation Pilot Plant (WIPP). Since wire ties have been used at Los Alamos National Laboratory (LANL) from 1980 to 1991 and the plastic ties from 1991 to the present, there are currently thousands of waste drums that cannot be shipped to the WIPP site. Repackaging the waste would be prohibitively expensive. Diffusion experiments performed on the above mentioned closures show that the diffusion rates of plastic tie and horse-tail closures are greater than the accepted value presented in the TRU-PACT 11 Safety Analysis Report (SAR). Diffusion rates for wire tie closures are not statistically different from the SAR value. Thus, drums containing bags with these closures can now potentially be certified which would allow for their consequent shipment to WIPP

Documentation of acceptable knowledge for Los Alamos National Laboratory Plutonium Facility TRU waste stream

International Nuclear Information System (INIS)

Montoya, A.J.; Gruetzmacher, K.M.; Foxx, C.L.; Rogers, P.Z.

1998-03-01

Characterization of transuranic waste from the LANL Plutonium Facility for certification and transportation to WIPP includes the use of acceptable knowledge as specified in the WIPP Quality Assurance Program Plan. In accordance with a site specific procedure, documentation of acceptable knowledge for retrievably stored and currently generated transuranic waste streams is in progress at LANL. A summary overview of the TRU waste inventory is complete and documented in the Sampling Plan. This document also includes projected waste generation, facility missions, waste generation processes, flow diagrams, times, and material inputs. The second part of acceptable knowledge documentation consists of assembling more detailed acceptable knowledge information into auditable records and is expected to require several years to complete. These records for each waste stream must support final assignment of waste matrix parameters, EPA hazardous waste numbers, and radionuclide characterization. They must also include a determination whether waste streams are defense waste streams for compliance with the WIPP Land Withdrawal Act. The LANL Plutonium Facility's mission is primarily plutonium processing in basic special nuclear material (SNM) research activities to support national defense and energy programs. It currently has about 100 processes ranging from SNM recovery from residues to development of plutonium 238 heat sources for space applications. Its challenge is to characterize and certify waste streams from such diverse and dynamic operations using acceptable knowledge. This paper reports the progress on the certification of the first of these waste streams to the WIPP WAC

Savannah River Site Operating Experience with Transuranic (TRU) Waste Retrieval

International Nuclear Information System (INIS)

Stone, K.A.; Milner, T.N.

2006-01-01

Drums of TRU Waste have been stored at the Savannah River Site (SRS) on concrete pads from the 1970's through the 1980's. These drums were subsequently covered with tarpaulins and then mounded over with dirt. Between 1996 and 2000 SRS ran a successful retrieval campaign and removed some 8,800 drums, which were then available for venting and characterization for WIPP disposal. Additionally, a number of TRU Waste drums, which were higher in activity, were stored in concrete culverts, as required by the Safety Analysis for the Facility. Retrieval of drums from these culverts has been ongoing since 2002. This paper will describe the operating experience and lessons learned from the SRS retrieval activities. (authors)

TRU Waste Management Program. Cost/schedule optimization analysis

International Nuclear Information System (INIS)

Detamore, J.A.; Raudenbush, M.H.; Wolaver, R.W.; Hastings, G.A.

1985-10-01

This Current Year Work Plan presents in detail a description of the activities to be performed by the Joint Integration Office Rockwell International (JIO/RI) during FY86. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO/RI by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO/RI tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance development, task monitoring, task progress information gathering and reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, and preparation of reports for DOE detailing program status. Program Analysis is performed by the JIO/RI to support identification and assessment of alternatives, and development of long-term TRU waste program capabilities. These analyses include short-term analyses in response to DOE information requests, along with performing an RH Cost/Schedule Optimization report. Systems models will be developed, updated, and upgraded as needed to enhance JIO/RI's capability to evaluate the adequacy of program efforts in various fields. A TRU program data base will be maintained and updated to provide DOE with timely responses to inventory related questions

Radiolytic decomposition of organic C-14 released from TRU waste

International Nuclear Information System (INIS)

Kani, Yuko; Noshita, Kenji; Kawasaki, Toru; Nishimura, Tsutomu; Sakuragi, Tomofumi; Asano, Hidekazu

2007-01-01

It has been found that metallic TRU waste releases considerable portions of C-14 in the form of organic molecules such as lower molecular weight organic acids, alcohols and aldehydes. Due to the low sorption ability of organic C-14, it is important to clarify the long-term behavior of organic forms under waste disposal conditions. From investigations on radiolytic decomposition of organic carbon molecules into inorganic carbonic acid, it is expected that radiation from TRU waste will decompose organic C-14 into inorganic carbonic acid that has higher adsorption ability into the engineering barriers. Hence we have studied the decomposition behavior of organic C-14 by gamma irradiation experiments under simulated disposal conditions. The results showed that organic C-14 reacted with OH radicals formed by radiolysis of water, to produce inorganic carbonic acid. We introduced the concept of 'decomposition efficiency' which expresses the percentage of OH radicals consumed for the decomposition reaction of organic molecules in order to analyze the experimental results. We estimated the effect of radiolytic decomposition on the concentration of organic C-14 in the simulated conditions of the TRU disposal system using the decomposition efficiency, and found that the concentration of organic C-14 in the waste package will be lowered when the decomposition of organic C-14 by radiolysis was taken into account, in comparison with the concentration of organic C-14 without radiolysis. Our prediction suggested that some amount of organic C-14 can be expected to be transformed into the inorganic form in the waste package in an actual system. (authors)

TRU partnership-Working smarter-Not harder

International Nuclear Information System (INIS)

Armstrong, D.W.; Briggs, S.R.; Martin, M.R.; Turner, D.R.

1994-01-01

The open-quotes TRU Partnershipclose quotes was initiated and continues to function under the catch phrase philosophy of open-quotes work smarter, not harderclose quotes. The parntership participants have realized that DOE no longer has the funding available to reinvent the wheel at each site. Information and experiences from each site need to accurately and timely provided to the other sites for their use. The project teams from the different TRU waste handling sites benefit enormously from the strong network that has developed between TRU partnership participants. The partnership working interface places design manager in touch with design manager, project manager with project manager, etc. across site boundaries, and equally important, across corporate boundaries. The TRU Partnership has created a team atmosphere for the participants. The team focus is on the common challenge of managing TRU waste projects to support site needs and the needs of the national TRU waste program. Although consistency of approach for all projects at any given site is important, the TRU Partnership provides an intersite forum to establish consistency and understanding across all DOE projects managing TRU waste. The TRU Partnership has adopted the Westinghouse Electric Corporation open-quotes Savings Through Sharingclose quotes philosophy as an integral part of its organizational objectives. As applied by the group, the approach concentrates on information and experiences that can enhance development and reduce costs for (TRU) waste projects

Post-Irradiation Examination of 237Np Targets for 238Pu Production

Energy Technology Data Exchange (ETDEWEB)

Morris, Robert Noel [ORNL; Baldwin, Charles A [ORNL; Hobbs, Randy W [ORNL; Schmidlin, Joshua E [ORNL

2015-01-01

Oak Ridge National Laboratory is recovering the US ²³⁸Pu production capability and the first step in the process has been to evaluate the performance of a ²³⁷Np target cermet pellet encased in an aluminum clad. The process proceeded in 3 steps; the first step was to irradiate capsules of single pellets composed of NpO₂ and aluminum power to examine their shrinkage and gas release. These pellets were formed by compressing sintered NpO₂ and aluminum powder in a die at high pressure followed by sintering in a vacuum furnace. Three temperatures were chosen for sintering the solution precipitated NpO₂ power used for pellet fabrication. The second step was to irradiate partial targets composed of 8 pellets in a semi-prototypical arrangement at the two best performing sintering temperatures to determine which temperature gave a pellet that performed the best under the actual planned irradiation conditions. The third step was to irradiate ~50 pellets in an actual target configuration at design irradiation conditions to assess pellet shrinkage and gas release, target heat transfer, and dimensional stability. The higher sintering temperature appeared to offer the best performance after one cycle of irradiation by having the least shrinkage, thus keeping the heat transfer gap between the pellets and clad small minimizing the pellet operating temperature. The final result of the testing was a target that can meet the initial production goals, satisfy the reactor safety requirements, and can be fabricated in production quantities. The current focus of the program is to verify that the target can be remotely dissembled, the pellets dissolved, and the ²³⁸Pu recovered. Tests are being conducted to examine these concerns and to compare results to code predictions. Once the performance of the full length targets has been quantified, the pellet ²³⁷Np loading will be revisited to determine if it can be

Comprehensive implementation plan for the DOE defense buried TRU- contaminated waste program

International Nuclear Information System (INIS)

Everette, S.E.; Detamore, J.A.; Raudenbush, M.H.; Thieme, R.E.

1988-02-01

In 1970, the US Atomic Energy Commission established a ''transuranic'' (TRU) waste classification. Waste disposed of prior to the decision to retrievably store the waste and which may contain TRU contamination is referred to as ''buried transuranic-contaminated waste'' (BTW). The DOE reference plan for BTW, stated in the Defense Waste Management Plan, is to monitor it, to take such remedial actions as may be necessary, and to re-evaluate its safety as necessary or in about 10-year periods. Responsibility for management of radioactive waste and byproducts generated by DOE belongs to the Secretary of Energy. Regulatory control for these sites containing mixed waste is exercised by both DOE (radionuclides) and EPA (hazardous constituents). Each DOE Operations Office is responsible for developing and implementing plans for long-term management of its radioactive and hazardous waste sites. This comprehensive plan includes site-by-site long-range plans, site characteristics, site costs, and schedules at each site. 13 figs., 15 tabs

TRU waste from the Superblock

International Nuclear Information System (INIS)

Coburn, T.T.

1997-01-01

This data analysis is to show that weapons grade plutonium is of uniform composition to the standards set by the Waste-Isolation Pilot Plant (WIPP) Transuranic Waste Characterization Quality Assurance Program Plan (TRUW Characterization QAPP, Rev. 2, DOE, Carlsbad Area Office, November 15, 1996). The major portion of Superblock transuranic (TRU) waste is glove-box trash contaminated with weapons grade plutonium. This waste originates in the Building 332 (B332) radioactive-materials area (RMA). Because each plutonium batch brought into the B332 RMA is well characterized with regard to nature and quantity of transuranic nuclides present, waste also will be well characterized without further analytical work, provided the batches are quite similar. A sample data set was created by examining the 41 incoming samples analyzed by Ken Raschke (using a γ-ray spectrometer) for isotopic distribution and by Ted Midtaune (using a calorimeter) for mass of radionuclides. The 41 samples were from separate batches analyzed May 1993 through January 1997. All available weapons grade plutonium data in Midtaune's files were used. Alloys having greater than 50% transuranic material were included. The intention of this study is to use this sample data set to judge ''similarity.''

Expert system for transuranic waste assay

Energy Technology Data Exchange (ETDEWEB)

Zoolalian, M.L.; Gibbs, A.; Kuhns, J.D.

1989-01-01

Transuranic wastes are generated at the Savannah River Site (SRS) as a result of routine production of nuclear materials. These wastes contain Pu-238 and Pu-239 and are placed into lined 55-gallon waste drums. The drums are placed on monitored storage pads pending shipment to the Waste Isolation Pilot Plant in New Mexico. A passive-active neutron (PAN) assay system is used to determine the mass of the radioactive material within the waste drums. Assay results are used to classify the wastes as either low-level or transuranic (TRU). During assays, the PAN assay system communicates with an IBM-AT computer. A Fortran computer program, called NEUT, controls and performs all data analyses. Unassisted, the NEUT program cannot adequately interpret assay results. To eliminate this limitation, an expert system shell was used to write a new algorithm, called the Transuranic Expert System (TRUX), to drive the NEUT program and add decision making capabilities for analysis of the assay results. The TRUX knowledge base was formulated by consulting with human experts in the field of neutron assay, by direct experimentation on the PAN assay system, and by observing operations on a daily basis. TRUX, with its improved ability to interpret assay results, has eliminated the need for close supervision by a human expert, allowing skilled technicians to operate the PAN assay system. 4 refs., 1 fig., 4 tabs.

Expert system for transuranic waste assay

International Nuclear Information System (INIS)

Zoolalian, M.L.; Gibbs, A.; Kuhns, J.D.

1989-01-01

Transuranic wastes are generated at the Savannah River Site (SRS) as a result of routine production of nuclear materials. These wastes contain Pu-238 and Pu-239 and are placed into lined 55-gallon waste drums. The drums are placed on monitored storage pads pending shipment to the Waste Isolation Pilot Plant in New Mexico. A passive-active neutron (PAN) assay system is used to determine the mass of the radioactive material within the waste drums. Assay results are used to classify the wastes as either low-level or transuranic (TRU). During assays, the PAN assay system communicates with an IBM-AT computer. A Fortran computer program, called NEUT, controls and performs all data analyses. Unassisted, the NEUT program cannot adequately interpret assay results. To eliminate this limitation, an expert system shell was used to write a new algorithm, called the Transuranic Expert System (TRUX), to drive the NEUT program and add decision making capabilities for analysis of the assay results. The TRUX knowledge base was formulated by consulting with human experts in the field of neutron assay, by direct experimentation on the PAN assay system, and by observing operations on a daily basis. TRUX, with its improved ability to interpret assay results, has eliminated the need for close supervision by a human expert, allowing skilled technicians to operate the PAN assay system. 4 refs., 1 fig., 4 tabs

Analysis of long-term impacts of TRU waste remaining at generator/storage sites for No Action Alternative 2

International Nuclear Information System (INIS)

Buck, J.W.; Bagaasen, L.M.; Bergeron, M.P.; Streile, G.P.

1997-09-01

This report is a supplement to the Waste Isolation Pilot Plant Disposal-Phase Final Supplemental Environmental Impact Statement (SEIS-II). Described herein are the underlying information, data, and assumptions used to estimate the long-term human-health impacts from exposure to radionuclides and hazardous chemicals in transuranic (TRU) waste remaining at major generator/storage sites after loss of institutional control under No Action Alternative 2. Under No Action Alternative 2, TRU wastes would not be emplaced at the Waste Isolation Pilot Plant (WIPP) but would remain at generator/storage sites in surface or near-surface storage. Waste generated at smaller sites would be consolidated at the major generator/storage sites. Current TRU waste management practices would continue, but newly generated waste would be treated to meet the WIPP waste acceptance criteria. For this alternative, institutional control was assumed to be lost 100 years after the end of the waste generation period, with exposure to radionuclides and hazardous chemicals in the TRU waste possible from direct intrusion and release to the surrounding environment. The potential human-health impacts from exposure to radionuclides and hazardous chemicals in TRU waste were analyzed for two different types of scenarios. Both analyses estimated site-specific, human-health impacts at seven major generator/storage sites: the Hanford Site (Hanford), Idaho National Engineering and Environmental Laboratory (INEEL), Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), Oak Ridge National Laboratory (ORNL), Rocky Flats Environmental Technology Site (RFETS), and Savannah River Site (SRS). The analysis focused on these seven sites because 99 % of the estimated TRU waste volume and inventory would remain there under the assumptions of No Action Alternative 2

Design and testing of a unique active Compton-suppressed LaBr3(Ce) detector system for improved sensitivity assays of TRU in remote-handled TRU wastes

Energy Technology Data Exchange (ETDEWEB)

J. K. Hartwell; M. E. McIlwain; J. A. Kulisek

2007-10-01

The US Department of Energy’s transuranic (TRU) waste inventory includes about 4,500 m3 of remote-handled TRU (RH-TRU) wastes composed of a variety of containerized waste forms having a contact surface dose rate that exceeds 2 mSv/hr (200 mrem/hr) containing waste materials with a total TRU concentration greater than 3700 Bq/g (100 nCi/g). As part of a research project to investigate the use of active Compton-suppressed room-temperature gamma-ray detectors for direct non-destructive quantification of the TRU content of these RH-TRU wastes, we have designed and purchased a unique detector system using a LaBr3(Ce) primary detector and a NaI(Tl) suppression mantle. The LaBr3(Ce) primary detector is a cylindrical unit ~25 mm in diameter by 76 mm long viewed by a 38 mm diameter photomultiplier. The NaI(Tl) suppression mantle (secondary detector) is 175 mm by 175 mm with a center well that accommodates the primary detector. An important feature of this arrangement is the lack of any “can” between the primary and secondary detectors. These primary and secondary detectors are optically isolated by a thin layer (.003") of aluminized kapton, but the hermetic seal and thus the aluminum can surrounds the outer boundary of the detector system envelope. The hermetic seal at the primary detector PMT is at the PMT wall. This arrangement virtually eliminates the “dead” material between the primary and secondary detectors, a feature that preliminary modeling indicated would substantially improve the Compton suppression capability of this device. This paper presents both the expected performance of this unit determined from modeling with MCNPX, and the performance measured in our laboratory with radioactive sources.

Determination of radionuclides {sup 90}Sr, {sup 239,240} Pu, {sup 238}Pu and {sup 241}Am in soil using methods of extraction chromatography and coprecipitation; Stanovenie radionuklidov {sup 90}Sr, {sup 239,240}Pu, : 2{sup 38}Pu a {sup 241}Am v pode vyuzivajuce metody extrakcnej chromatografie a spoluzrazania

Energy Technology Data Exchange (ETDEWEB)

Gardonova, V.; Dulanska, S.; Bilohuscin, J. [Univerzita Komenskeho, Prirodovedecka fakulta, Katedra jadrovej chemie, 84215 Bratislava (Slovakia)

2013-04-16

Ecosystems, which include soil and sediments, contain not only natural radionuclides but also radionuclides from deposits, mainly {sup 137}Cs, {sup 90}Sr and {alpha}-emitting radionuclides such as {sup 239,240}Pu, {sup 238}Pu and {sup 241}Am, that originate from global fallout and nuclear facilities leaks worldwide. The goal of the work was optimization of separation and determination of {sup 90}Sr, {sup 238}Pu, {sup 239,240}Pu and {sup 241}Am in soil from Slovak Republic. The newest methods were applied for separation of selected radionuclides based on coprecipitation with oxalic salts and extraction chromatography using selective commercial sorbents. (authors)

Speciation analysis of 129I, 137Cs, 232Th, 238U, 239Pu and 240Pu in environmental soil and sediment

DEFF Research Database (Denmark)

Qiao, Jixin; Hansen, Violeta; Hou, Xiaolin

2012-01-01

The environmental mobility and bioavailability of radionuclides are related to their physicochemical forms, namely species. We here present a speciation analysis of important radionuclides including 129I (also 127I), 137Cs, 232Th, 238U and plutonium isotopes (239Pu and 240Pu) in soil (IAEA-375......) and sediment (NIST-4354) standard reference materials and two fresh sediment samples from Øvre Heimdalsvatnet Lake, Norway. A modified sequential extraction protocol was used for the speciation analysis of these samples to obtain fractionation information of target radionuclides. Analytical results reveal...

Hydrogen venting characteristics of commercial carbon-composite filters and applications to TRU waste

International Nuclear Information System (INIS)

Callis, E.L.; Marshall, R.S.; Cappis, J.H.

1997-04-01

The generation of hydrogen (by radiolysis) and of other potentially flammable gases in radioactive wastes which are in contact with hydrogenous materials is a source of concern, both from transportation and on-site storage considerations. Because very little experimental data on the generation and accumulation of hydrogen was available in actual waste materials, work was initiated to experimentally determine factors affecting the concentration of hydrogen in the waste containers, such as the hydrogen generation rate, (G-values) and the rate of loss of hydrogen through packaging and commercial filter-vents, including a new design suitable for plastic bags. This report deals only with the venting aspect of the problem. Hydrogen venting characteristics of two types of commercial carbon-composite filter-vents, and two types of PVC bag closures (heat-sealed and twist-and-tape) were measured. Techniques and equipment were developed to permit measurement of the hydrogen concentration in various layers of actual transuranic (TRU) waste packages, both with and without filter-vents. A test barrel was assembled containing known configuration and amounts of TRU wastes. Measurements of the hydrogen in the headspace verified a hydrogen release model developed by Benchmark Environmental Corporation. These data were used to calculate revised wattage Emits for TRU waste packages incorporating the new bag filter-vent

Terminating Safeguards on Excess Special Nuclear Material: Defense TRU Waste Clean-up and Nonproliferation - 12426

Energy Technology Data Exchange (ETDEWEB)

Hayes, Timothy [Los Alamos National Laboratory, Carlsbad Operations Group (United States); Nelson, Roger [Department Of Energy, Carlsbad Operations Office (United States)

2012-07-01

The Department of Energy (DOE) and the National Nuclear Security Administration (NNSA) manages defense nuclear material that has been determined to be excess to programmatic needs and declared waste. When these wastes contain plutonium, they almost always meet the definition of defense transuranic (TRU) waste and are thus eligible for disposal at the Waste Isolation Pilot Plant (WIPP). The DOE operates the WIPP in a manner that physical protections for attractiveness level D or higher special nuclear material (SNM) are not the normal operating condition. Therefore, there is currently a requirement to terminate safeguards before disposal of these wastes at the WIPP. Presented are the processes used to terminate safeguards, lessons learned during the termination process, and how these approaches might be useful for future defense TRU waste needing safeguards termination prior to shipment and disposal at the WIPP. Also described is a new criticality control container, which will increase the amount of fissile material that can be loaded per container, and how it will save significant taxpayer dollars. Retrieval, compliant packaging and shipment of retrievably stored legacy TRU waste has dominated disposal operations at WIPP since it began operations 12 years ago. But because most of this legacy waste has successfully been emplaced in WIPP, the TRU waste clean-up focus is turning to newly-generated TRU materials. A major component will be transuranic SNM, currently managed in safeguards-protected vaults around the weapons complex. As DOE and NNSA continue to consolidate and shrink the weapons complex footprint, it is expected that significant quantities of transuranic SNM will be declared surplus to the nation's needs. Safeguards termination of SNM varies due to the wide range of attractiveness level of the potential material that may be directly discarded as waste. To enhance the efficiency of shipping waste with high TRU fissile content to WIPP, DOE designed an

Conceptual designs for a long term 238PuO2 storage vessel

International Nuclear Information System (INIS)

Kwon, D.M.; Replogle, W.C.

1996-08-01

This is a report on conceptual designs for a long term, 250 years, storage container for plutonium oxide ([sup 238]PuO[sub 2]). These conceptual designs are based on the use of a quartz filter to release the helium generated during the plutonium decay. In this report a review of filter material selection, design concepts, thermal modeling, and filter performance are discussed

Development of TRU waste mobile analysis methods for RCRA-regulated metals

International Nuclear Information System (INIS)

Mahan, C.A.; Villarreal, R.; Drake, L.; Figg, D.; Wayne, D.; Goldstein, S.

1998-01-01

This is the final report of a one-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). Glow-discharge mass spectrometry (GD-MS), laser-induced breakdown spectroscopy (LIBS), dc-arc atomic-emission spectroscopy (DC-ARC-AES), laser-ablation inductively-coupled-plasma mass spectrometry (LA-ICP-MS), and energy-dispersive x-ray fluorescence (EDXRF) were identified as potential solid-sample analytical techniques for mobile characterization of TRU waste. Each technology developers was provided with surrogate TRU waste samples in order to develop an analytical method. Following successful development of the analytical method, five performance evaluation samples were distributed to each of the researchers in a blind round-robin format. Results of the round robin were compared to known values and Transuranic Waste Characterization Program (TWCP) data quality objectives. Only two techniques, DC-ARC-AES and EDXRF, were able to complete the entire project. Methods development for GD-MS and LA-ICP-MS was halted due to the stand-down at the CMR facility. Results of the round-robin analysis are given for the EDXRF and DCARC-AES techniques. While DC-ARC-AES met several of the data quality objectives, the performance of the EDXRF technique by far surpassed the DC-ARC-AES technique. EDXRF is a simple, rugged, field portable instrument that appears to hold great promise for mobile characterization of TRU waste. The performance of this technique needs to be tested on real TRU samples in order to assess interferences from actinide constituents. In addition, mercury and beryllium analysis will require another analytical technique because the EDXRF method failed to meet the TWCP data quality objectives. Mercury analysis is easily accomplished on solid samples by cold vapor atomic fluorescence (CVAFS). Beryllium can be analyzed by any of a variety of emission techniques

Final Environmental Impact Statement for Treating Transuranic (TRU)/Alpha Low-level Waste at the Oak Ridge National Laboratory Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

N/A

2000-06-30

The DOE proposes to construct, operate, and decontaminate/decommission a TRU Waste Treatment Facility in Oak Ridge, Tennessee. The four waste types that would be treated at the proposed facility would be remote-handled TRU mixed waste sludge, liquid low-level waste associated with the sludge, contact-handled TRU/alpha low-level waste solids, and remote-handled TRU/alpha low-level waste solids. The mixed waste sludge and some of the solid waste contain metals regulated under the Resource Conservation and Recovery Act and may be classified as mixed waste. This document analyzes the potential environmental impacts associated with five alternatives--No Action, the Low-Temperature Drying Alternative (Preferred Alternative), the Vitrification Alternative, the Cementation Alternative, and the Treatment and Waste Storage at Oak Ridge National Laboratory (ORNL) Alternative.

NDA PDP Program PuO2 increased particle size specification and design

International Nuclear Information System (INIS)

Marshall, R.S.; Taggart, D.P.; Becker, G.K.; Woon, W.Y.

1996-01-01

Provisions in the National TRU Program Quality Assurance Program Plan require an assessment of performance for nondestructive waste assay (NDA) systems employed in the program. This requirement is in part fulfilled through the use of Performance Demonstration programs. In order to optimize the quality and quantity of information acquired during a given Performance Demonstration Program cycle, the assessment employed is to be carefully specified and designed. The assessment must yield measurement system performance data meaningful with respect to NDA system capability to accommodate attributes of interest known to occur in actual waste forms. The design and specification of the increased particle size PuO 2 PDP working reference materials (WRMs) is directed at providing a straightforward mechanism to assess waste NDA system capability to account for biases introduced by large PuO 2 particles. The increased particle size PuO 2 PDP WRM design addresses actual waste form attributes associated with PuO 2 particle size and distributions thereof, the issue of a known and stable WRM configuration and equally important appropriate certification and tractability considerations

TRU Self-Recycling in a High Temperature Gas Cooled Reactor

International Nuclear Information System (INIS)

Jo, Chang Keun

2013-01-01

Conclusions: • Evaluated the core characteristics and performance for SR-HTR. • Self-recycling of self-generated TRUs is feasible and deep-burning of the self-generated TRU can be achieved in SR-HTR. • From the results, ⇒ TRU discharge burnup is over 60% and the uranium fuel can also be utilized very efficiently in the SR-HTR core. ⇒ In the case of separate TRU loading, the power fraction of the TRU fueled zone is substantially smaller (~10%) than that of the uranium fueled zone. ⇒ The transmutation of Pu-239 is nearly complete (~99%) in the SR-HTR core and that of Pu-241 is also extremely high. ⇒ The decay heat of SR-HTR core is evaluated to be similar to that of the 3-ring UO 2 -only loaded HTR core. • A TF-coupled analysis is required for a more concrete evaluation of TRU deep-burn in an SR-HTR

Toxicity of inhaled 238PuO2 in beagle dogs. A. Monodisperse 1.5 μm 238PuO2. B. Monodisperse 3.0 μm 238PuO2 particles. III

International Nuclear Information System (INIS)

Lustgarten, C.S.; Mewhinney, J.A.; Hobbs, C.H.; Halliwell, W.H.; Jones, R.K.; Mauderly, J.L.; McClellan, R.O.; Mo, T.; Pickrell, J.A.

1976-01-01

To obtain essential information on the importance of the homogeneity or non-homogeneity of the radiation dose to lung (the hot particle question), Beagle dogs have been exposed to monodisperse aerosols (sigma/sub g/ 238 PuO 2 of either 1.5 μm or 3.0 μm aerodynamic diameter (AD). By using monodisperse particles of these two sizes, the average dose to lung is held constant for a given initial lung burden, but the local alpha dose around the two sizes of particles varies by a factor of about ten. All exposures have been completed with 72 days exposed to each of the two particle sizes of 238 PuO 2 (total of 144 dogs) resulting in graded initial lung burdens which range from .005 to 2.2 μCi/kg of body weight. Twenty-four dogs exposed to the diluent aerosol are serving as controls. The animals will be studied over their total life span. Two exposed dogs have died from pulmonary injury: Dog 710C (with an initial lung burden of 2.0 μCi/kg) died at 631 days after inhalation of 3.0 μm AD aerosol. The cause of death was radiation pneumonitis and pulmonary fibrosis, Dog 746B (with an initial lung burden of 1.3 μCi/kg) died at 791 days after inhalation of 1.5 μm AD aerosol. Death was attributed to intrapulmonic hemorrhage resulting from a degenerative vasculitis. One control dog (721A) was euthanized at 820 days after exposure due to a meningitis and encephalomalacia that caused a severe central nervous system disorder that made the dog difficult to handle.A leukopenia in exposed dogs to date has occurred earlier and to a greater degree in dogs exposed to 3.0 μm AD particles than in dogs that recevied 1.5 μm AD particles. One hundred forty-two exposed and 23 control dogs are surviving at 175 to 1024 days after exposure

Optimization of the binary breeder reactor. VIII annular core fueled with 233U - 238U and Pu-238U

International Nuclear Information System (INIS)

Nascimento, J.A. do; Ishiguro, Y.

1988-04-01

First cycle burnup characteristics of a 1200 MWe binary breeder reactor with annular core fueled with metallic 233 U- 238 U-Zr, Pu- 238 U-Zr and Th in the blankets have been analysed. The Doppler effect is small as expected in a metal fueled fast reactor. The sodium void reactivity is, in general, smaller than in metal fueled homogeneous fast reactors of 1 m core height. The estimates of the required and available control rod worths show a large shutdown margin throughout the operational cycle. There are flexibilities in the blanket fueling and well balanced breeding in the two cycles, uranium and thorium, with doubling times of about 20 years are possible. (author) [pt

The production of {sup 238-242}Pu(n,γ){sup 239-243}Pu fissionable fluids in a fusion-fission hybrid reactor

Energy Technology Data Exchange (ETDEWEB)

Guenay, Mehtap [Inoenue Univ., Malatya (Turkey). Physics Dept.

2014-03-15

In this study, the effect of spent fuel grade plutonium content on {sup 239-243}Pu was investigated in a designed hybrid reactor system. In this system, the fluids were composed of a molten salt, heavy metal mixture with increased mole fractions 99-95 % Li{sub 20}Sn{sub 80}-1-5 % SFG-Pu, 99-95 % Li{sub 20}Sn{sub 80}-1-5 % SFG-PuF{sub 4}, 99-95 % Li{sub 20}Sn{sub 80}-1-5 % SFG-PuO{sub 2}. Beryllium (Be) is a neutron multiplier by (n,2n) reactions. Thence, a Be zone of 3 cm thickness was used in order to contribute to fissile fuel breeding between the liquid first wall and a 9Cr2WVTa ferritic steel blanket which is used as structural material. The production of {sup 238-242}Pu(n,γ){sup 239-243}Pu was calculated in liquid first wall, blanket and shielding zones. Three-dimensional nucleonic calculations were performed by using the most recent version MCNPX-2.7.0 Monte Carlo code and nuclear data library ENDF/B-VII.0. (orig.)

Pilot scale, alpha disassembly and decontamination facility at the Savannah River Laboratory

International Nuclear Information System (INIS)

Cadieux, J.R.; Becker, G.W. Jr.; Richardson, G.W.; Coogler, A.L.

1982-01-01

An alpha-contained pilot facility is being built at the Savannah River Laboratory (SRL) for research into the disassembly and dcontamination of noncombustible, Transuranic (TRU) waste. The design and program objectives for the facility are presented along with the initial test results from laboratory scale decontamination experiments with Pu-238 and Cm-244

Bioaccumulation, distribution, and dose of 241Am, 244Cm, and 238Pu in developing fish embryos

International Nuclear Information System (INIS)

Till, J.E.; Frank, M.L.

1977-01-01

The dose from several actinide elements to a sensitive stage in the development of one type of aquatic biota, the fish egg, was assessed. An investigation was made of the uptake and distribution of 241 Am, 244 Cm and 238 Pu by developing embryos of fish. Eggs from ripe carp, Cyprinos carpio, that had been spawned in the laboratory were placed in dishes containing 241 Am(III)- 244 Cm(III)-, or 238 Pu(IV)-citrate in solution at an activity concentration of approximately 10 -3 μCi/ml. Samples of eggs were taken at seven intervals during the 72-hour period of embryogenesis. Egg contents were separated from the membrane prior to analysis to quantify the activity that penetrated the chorion. Autoradiographs of 16-μm thick egg sections confirmed that alpha radioactivity was present in the egg contents and permitted the distribution of activity to be determined. Concentration factors were calculated based on activity ratios for the egg contents (excluding the chorion) over the development period. Maximum concentration factors occurred at hatching and were found to be 25, 40 and 3 for 241 Am, 244 Cm and 238 Pu, respectively. Collectively, these data were used to estimate the dose from americium, curium and plutonium in natural ecosystems to developing fish eggs which have similar embryological characteristics as carp

Evaluation of Aqueous and Powder Processing Techniques for Production of Pu-238-Fueled General Purpose Heat Sources

Energy Technology Data Exchange (ETDEWEB)

2008-06-01

This report evaluates alternative processes that could be used to produce Pu-238 fueled General Purpose Heat Sources (GPHS) for radioisotope thermoelectric generators (RTG). Fabricating GPHSs with the current process has remained essentially unchanged since its development in the 1970s. Meanwhile, 30 years of technological advancements have been made in the fields of chemistry, manufacturing, ceramics, and control systems. At the Department of Energy’s request, alternate manufacturing methods were compared to current methods to determine if alternative fabrication processes could reduce the hazards, especially the production of respirable fines, while producing an equivalent GPHS product. An expert committee performed the evaluation with input from four national laboratories experienced in Pu-238 handling.

Preliminary identification of interfaces for certification and transfer of TRU waste to WIPP

International Nuclear Information System (INIS)

Whitty, W.J.; Ostenak, C.A.; Pillay, K.K.S.

1982-02-01

This study complements the national program to certify that newly generated and stored, unclassified defense transuranic (TRU) wastes meet the Waste Isolation Pilot Plant (WIPP) Waste Acceptance Criteria. The objectives of this study were to identify (1) the existing organizational structure at each of the major waste-generating and shipping sites and (2) the necessary interfaces between the waste shippers and WIPP. The interface investigations considered existing waste management organizations at the shipping sites and the proposed WIPP organization. An effort was made to identify the potential waste-certifying authorities and the lines of communication within these organizations. The long-range goal of this effort is to develop practicable interfaces between waste shippers and WIPP to enable the continued generation, interim storage, and eventual shipment of certified TRU wastes to WIPP. Some specific needs identified in this study include: organizational responsibility for certification procedures and quality assurance (QA) program; simple QA procedures; and specification and standardization of reporting forms and procedures, waste containers, and container labeling, color coding, and code location

Position paper on flammability concerns associated with TRU waste destined for WIPP

International Nuclear Information System (INIS)

1991-04-01

The Waste Isolation Pilot Plant (WIPP), in southeastern New Mexico,is an underground repository, designed for the safe geologic disposal of transuranic (TRU) wastes generated from defense-related activities of the US Department of Energy (DOE). The WIPP storage rooms are mined in a bedded salt (halite) formation, and are located 2150 feet below the surface. After the disposal of waste in the storage rooms, closure of the repository is expected to occur by creep (plastic flow) of the salt formation, with the waste being permanently isolated from the surrounding environment. This paper has evaluated the issue of flammability concerns associated with TRU waste to be shipped to WIPP, including a review of possible scenarios that can potentially contribute to the flammability. The paper discusses existing regulations that address potential flammability concerns, presents an analysis of previous flammability-related incidents at DOE sites with respect to the current regulations, and finally, examines the degree of assurance these regulations provide in safeguarding against flammability concerns during transportation and waste handling. 50 refs., 7 figs., 7 tabs

TRU partnership-benefits to the national TRU program

International Nuclear Information System (INIS)

Lippis, J.; Lott, S.A.

1995-01-01

Because increased regulatory authority has been given to the states, the management of transuranic (TRU) wastes varies considerably. One effective tool for facilitating better communications, coordination, and cooperation among the generator/storage sites is the formation of topic specific interface working groups. The National TRU Program supports these groups, and in 1994, a policy was adopted to manage these interface working groups

Current technics and management strategy for Pu-contaminated wastes at PNC

International Nuclear Information System (INIS)

1981-02-01

Power Reactor and Nuclear Fuel Development Corporation (PNC) was designated as a leading organization for the Pu-contaminated waste technology program in Japan. For this purpose, number of efforts in the research and development are proceeding. That is, Pu-contaminated waste technology including volume reduction system and the immobilization of wastes is being developed. The design of a Pu-contaminated waste treatment facility (PWTF) is being made for the demonstration of the technology developed. Studies are in progress to find the criteria for waste products in disposal. The current procedures and strategy for the management of Pu-contaminated wastes at PNC are described as follows: current and future management; technology development including controlled air incineration, acid digestion, immobilization melting, dismantling, and liquid waste treatment; the Pu-contaminated waste treatment facility. (J.P.N.)

Alkaline degradation of organic materials contained in TRU wastes under repository conditions

International Nuclear Information System (INIS)

Otsuka, Yoshiki; Banba, Tsunetaka

2007-09-01

Alkaline degradation tests for 9 organic materials were conducted under the conditions of TRU waste disposal: anaerobic alkaline conditions. The tests were carried out at 90degC for 91 days. The sample materials for the tests were selected from the standpoint of constituent organic materials of TRU wastes. It has been found that cellulose and plastic solidified products are degraded relatively easily and that rubbers are difficult to degrade. It could be presumed that the alkaline degradation of organic materials occurs starting from the functional group in the material. Therefore, the degree of degradation difficulty is expected to be dependent on the kinds of functional group contained in the organic material. (author)

Determination of plutonium isotopes (²³⁸Pu, ²³⁹Pu, ²⁴⁰Pu, ²⁴¹Pu) in environmental samples using radiochemical separation combined with radiometric and mass spectrometric measurements

DEFF Research Database (Denmark)

Xu, Yihong; Qiao, Jixin; Hou, Xiaolin

2014-01-01

counting and alpha spectrometry) and inductively coupled plasma mass spectrometry (ICP-MS) were applied for the measurement of plutonium isotopes. The decontamination factors for uranium were significantly improved up to 7.5×105 for 20 g soil compared to the level reported in the literature......, this is critical for the measurement of plutonium isotopes using mass spectrometric technique. Although the chemical yield of Pu in the entire procedure is about 55%, the analytical results of IAEA soil 6 and IAEA-367 in this work are in a good agreement with the values reported in the literature or reference......Pu. However, it is impossible to measure 238Pu using ICP-MS in environmental samples even a decontamination factor as high as 106 for uranium was obtained by chemical separation....

{sup 238}Pu, {sup 239+240}Pu and {sup 241}Am levels in the terrestrial and aquatic environment of the Loire and Garonne rivers basins (France)

Energy Technology Data Exchange (ETDEWEB)

Rousseau, G.; Mokili, M.B.; Le Roy, C.; Pagano, V. [SUBATECH/IN2P3 (France); Gontier, G.; Boyer, C. [EDF-DPI-DIN-CIDEN (France); Chardon, P. [CNRS/IN2P3 (France); Hemidy, P.Y. [EDF-DPN-UNIE-GPRE-IEV (France)

2014-07-01

Plutonium and americium long-lived alpha emitter isotopes can be found in the environment because of atmospheric global fallout due to thermonuclear tests performed between 1945 and 1980, to the American SNAP 9A satellite explosion in 1964, to the Chernobyl nuclear power plant accident,... In France, the nuclear safety authority does not allow the release of artificial alpha emitters from nuclear power plants. Thus, monitoring is performed to verify the absence of these alpha emitters in liquid discharges to respect the limits set by the regulations. These thresholds ensure a very low dosimetric impact to the population compared to other radionuclides. With the objective of environmental monitoring around nuclear facilities, activity measurements of long-lived alpha emitters are carried out to detect the traces of these radionuclides. Analysis of low activity by alpha spectrometry after chemical steps were performed and used to determine the {sup 238}Pu, {sup 239+240}Pu and {sup 241}Am activities on a large set of environmental solid samples likely to be encountered in environmental monitoring as soils, sediments, terrestrial and aquatic bio-indicators. The samples collected in the terrestrial and aquatic environment of the Loire and Garonne rivers basins (France) was investigated for the 2009-2014 period. It was found that the mean activity concentration of the most frequently detected was for the radionuclide {sup 238}Pu: from <0.00031 to 0.0061 Bq/kg dry in terrestrial samples and from <0.00086 to 0.011 Bq/kg dry in aquatic samples; for the radionuclide {sup 239+240}Pu: from 0.00041 to 0.150 Bq/kg dry in terrestrial samples and from 0.0023 to 0.240 Bq/kg dry in aquatic samples and for the radionuclide {sup 241}Am: from <0.00086 to 0.087 Bq/kg dry in terrestrial samples and from 0.0022 to 0.120 Bq/kg dry in aquatic samples. {sup 238}Pu/{sup 239+240}Pu and {sup 241}Am/{sup 239+240}Pu ratios determined are in accordance with an environmental contamination due to

Development of the remote-handled transuranic waste radioassay data quality objectives. An evaluation of RH-TRU waste inventories, characteristics, radioassay methods and capabilities

Energy Technology Data Exchange (ETDEWEB)

Meeks, A.M.; Chapman, J.A.

1997-09-01

The Waste Isolation Pilot Plant will accept remote-handled transuranic waste as early as October of 2001. Several tasks must be accomplished to meet this schedule, one of which is the development of Data Quality Objectives (DQOs) and corresponding Quality Assurance Objectives (QAOs) for the assay of radioisotopes in RH-TRU waste. Oak Ridge National Laboratory (ORNL) was assigned the task of providing to the DOE QAO, information necessary to aide in the development of DQOs for the radioassay of RH-TRU waste. Consistent with the DQO process, information needed and presented in this report includes: identification of RH-TRU generator site radionuclide data that may have potential significance to the performance of the WIPP repository or transportation requirements; evaluation of existing methods to measure the identified isotopic and quantitative radionuclide data; evaluation of existing data as a function of site waste streams using documented site information on fuel burnup, radioisotope processing and reprocessing, special research and development activities, measurement collection efforts, and acceptable knowledge; and the current status of technologies and capabilities at site facilities for the identification and assay of radionuclides in RH-TRU waste streams. This report is intended to provide guidance in developing the RH-TRU waste radioassay DQOs, first by establishing a baseline from which to work, second, by identifying needs to fill in the gaps between what is known and achievable today and that which will be required before DQOs can be formulated, and third, by recommending measures that should be taken to assure that the DQOs in fact balance risk and cost with an achievable degree of certainty.

Development of the remote-handled transuranic waste radioassay data quality objectives. An evaluation of RH-TRU waste inventories, characteristics, radioassay methods and capabilities

International Nuclear Information System (INIS)

Meeks, A.M.; Chapman, J.A.

1997-09-01

The Waste Isolation Pilot Plant will accept remote-handled transuranic waste as early as October of 2001. Several tasks must be accomplished to meet this schedule, one of which is the development of Data Quality Objectives (DQOs) and corresponding Quality Assurance Objectives (QAOs) for the assay of radioisotopes in RH-TRU waste. Oak Ridge National Laboratory (ORNL) was assigned the task of providing to the DOE QAO, information necessary to aide in the development of DQOs for the radioassay of RH-TRU waste. Consistent with the DQO process, information needed and presented in this report includes: identification of RH-TRU generator site radionuclide data that may have potential significance to the performance of the WIPP repository or transportation requirements; evaluation of existing methods to measure the identified isotopic and quantitative radionuclide data; evaluation of existing data as a function of site waste streams using documented site information on fuel burnup, radioisotope processing and reprocessing, special research and development activities, measurement collection efforts, and acceptable knowledge; and the current status of technologies and capabilities at site facilities for the identification and assay of radionuclides in RH-TRU waste streams. This report is intended to provide guidance in developing the RH-TRU waste radioassay DQOs, first by establishing a baseline from which to work, second, by identifying needs to fill in the gaps between what is known and achievable today and that which will be required before DQOs can be formulated, and third, by recommending measures that should be taken to assure that the DQOs in fact balance risk and cost with an achievable degree of certainty

Transuranic and tracer simulant resuspension. [/sup 238/Pu, /sup 239/Pu, /sup 240/Pu

Energy Technology Data Exchange (ETDEWEB)

Sehmel, G. A.

1977-07-01

Plutonium resuspension results are summarized for experiments conducted at Rocky Flats, onsite on the Hanford reservation, and for winds blowing from offsite onto the Hanford reservation near the Prosser barricade boundary. In each case, plutonium resuspension was shown by increased airborne plutonium concentrations as a function of either wind speed or as compared to fallout levels. All measured airborne concentrations were below maximum permissible concentrations (MPC). Both plutonium and cesium concentrations on airborne soil were normalized by the quantity of airborne soil sampled. Airborne radionuclide concentrations in ..mu..Ci/g were related to published values for radionuclide concentrations on surface soils. For this ratio of radionuclide concentration per gram on airborne soil divided by that for ground surface soil, there are eight orders of magnitude uncertainty from 10/sup -4/ to 10/sup 4/. Horizontal plutonium fluxes on airborne nonrespirable soils at all three sites were bracketed within the same three to four orders of magnitude from 10/sup -7/ to 10/sup -3/ ..mu..Ci/(m/sup 2/ day) for plutonium-239 and 10/sup -8/ to 10/sup -5/ ..mu..Ci/(m/sup 2/ day) for plutonium-238. These are the entire experimental base for nonrespirable airborne plutonium transport. Airborne respirable plutonium-239 concentrations increased with wind speed for a southeast wind direction coming from offsite near the Hanford reservation Prosser barricade. Airborne plutonium fluxes on nonrespirable particles had isotopic ratios, /sup 240/Pu//sup 239 +240/Pu, similar to weapons grade plutonium rather than fallout plutonium. Resuspension rates were summarized for controlled inert particle tracer simulant experiments. Wind resuspension rates for tracers increased with wind speed to about the fifth power.

MICROBIAL TRANSFORMATIONS OF TRU AND MIXED WASTES: ACTINIDE SPECIATION AND WASTE VOLUME REDUCTION.

Energy Technology Data Exchange (ETDEWEB)

FRANCIS, A.J.; DODGE, C.J.

2006-11-16

The overall goals of this research project are to determine the mechanism of microbial dissolution and stabilization of actinides in Department of Energy's (DOE) TRU wastes, contaminated sludges, soils, and sediments. This includes (1) investigations on the fundamental aspects of microbially catalyzed radionuclide and metal transformations (oxidation/reduction reactions, dissolution, precipitation, chelation); (2) understanding of the microbiological processes that control speciation and alter the chemical forms of complex inorganic/organic contaminant mixtures; and (3) development of new and improved microbially catalyzed processes resulting in immobilization of metals and radionuclides in the waste with concomitant waste volume reduction.

MICROBIAL TRANSFORMATIONS OF TRU AND MIXED WASTES: ACTINIDE SPECIATION AND WASTE VOLUME REDUCTION

Energy Technology Data Exchange (ETDEWEB)

Francis, A.J.; Dodge, C.J.

2006-06-01

The overall goals of this research project are to determine the mechanism of microbial dissolution and stabilization of actinides in Department of Energy’s (DOE) TRU wastes, contaminated sludges, soils, and sediments. This includes (i) investigations on the fundamental aspects of microbially catalyzed radionuclide and metal transformations (oxidation/reduction reactions, dissolution, precipitation, chelation); (ii) understanding of the microbiological processes that control speciation and alter the chemical forms of complex inorganic/organic contaminant mixtures; and (iii) development of new and improved microbially catalyzed processes resulting in immobilization of metals and radionuclides in the waste with concomitant waste volume reduction.

MICROBIAL TRANSFORMATIONS OF TRU AND MIXED WASTES: ACTINIDE SPECIATION AND WASTE VOLUME REDUCTION

Energy Technology Data Exchange (ETDEWEB)

Francis, A.J.; Dodge, C.J.

2006-06-01

The overall goals of this research project are to determine the mechanism of microbial dissolution and stabilization of actinides in Department of Energy's (DOE) TRU wastes, contaminated sludges, soils, and sediments. This includes (1) investigations on the fundamental aspects of microbially catalyzed radionuclide and metal transformations (oxidation/reduction reactions, dissolution, precipitation, chelation); (2) understanding of the microbiological processes that control speciation and alter the chemical forms of complex inorganic/organic contaminant mixtures; and (3) development of new and improved microbially catalyzed processes resulting in immobilization of metals and radionuclides in the waste with concomitant waste volume reduction.

Analysis of TRU waste for RCRA-listed elements

International Nuclear Information System (INIS)

Mahan, C.; Gerth, D.; Yoshida, T.

1996-01-01

Analytical methods for RCRA listed elements on Portland cement type waste have been employed using both microwave and open hot plate digestions with subsequent analysis by inductively coupled plasma atomic emission spectroscopy (ICP-AES), inductively coupled plasma mass spectrometry (ICP-AES), inductively coupled plasma mass spectrometry (ICP-MS), graphite furnace atomic absorption (GFAA) and cold vapor atomic absorption and fluorescence (CVAA/CVAFS). Four different digestion procedures were evaluated including an open hot plate nitric acid digestion, EPA SW-846 Method 3051, and 2 methods using modifications to Method 3051. The open hot plate and the modified Method 3051, which used aqua regia for dissolution, were the only methods which resulted in acceptable data quality for all 14 RCRA-listed elements. Results for the nitric acid open hot plate digestion were used to qualify the analytical methods for TRU waste characterization, and resulted in a 99% passing score. Direct chemical analysis of TRU waste is being developed at Los Alamos National Laboratory in an attempt to circumvent the problems associated with strong acid digestion methods. Technology development includes laser induced breakdown spectroscopy (LIBS), laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS), dc arc CID atomic emission spectroscopy (DC-AES), and glow discharge mass spectrometry (GDMS). Analytical methods using the Portland cement matrix are currently being developed for each of the listed techniques. Upon completion of the development stage, blind samples will be distributed to each of the technology developers for RCRA metals characterization

Parametric Criticality Safety Calculations for Arrays of TRU Waste Containers

Energy Technology Data Exchange (ETDEWEB)

Gough, Sean T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-26

The Nuclear Criticality Safety Division (NCSD) has performed criticality safety calculations for finite and infinite arrays of transuranic (TRU) waste containers. The results of these analyses may be applied in any technical area onsite (e.g., TA-54, TA-55, etc.), as long as the assumptions herein are met. These calculations are designed to update the existing reference calculations for waste arrays documented in Reference 1, in order to meet current guidance on calculational methodology.

Assessment of the Mechanisms for Sr-90 and TRU Removal from Complexant-Containing Tank Wastes at Hanford

International Nuclear Information System (INIS)

Hallen, Richard T.; Geeting, John GH; Lilga, Michael A.; Hart, Todd R.; Hoopes, Francis V.

2005-01-01

Small-scale tests (∼20 mL) were conducted with samples from Hanford underground storage tanks AN-102 and AN-107 to assess the mechanisms for removing Sr-90 and transuranics (TRU) from the liquid (supernatant) portion of the waste. The Sr-90 and TRU must be removed (decontaminated), in addition to Cs-137 and the entrained solids, before the supernatant can be disposed of as low-activity waste. Experiments were conducted with various reagents and modified Sr/TRU removal process conditions to more fully understand the reaction mechanisms. The optimized treatment conditions--no added hydroxide, addition of Sr (0.02M target concentration) followed by sodium permanganate (0.02M target concentration) with mixing at ambient temperature--were used as a reference for comparison. The waste was initially two orders of magnitude undersaturated with Sr; the addition of nonradioactive Sr(NO?) ? saturated the supernatant, resulting in isotopic dilution and precipitation of Sr-90 as SrCO?. The reaction chemistry of Mn species relevant to the mechanism of TRU removal by permanganate treatment was evaluated, along with the importance of various mechanisms for decontamination, such as precipitation, absorption, ligand exchange, and oxidation of organic complexants. For TRU removal, permanganate addition generally gave the highest DF. The addition of Mn of lower oxidation states (II, IV, and VI) also resulted in good TRU removal, as did complexant oxidation with periodate and addition of Zr(IV) for ligand exchange. These results suggest that permanganate treatment leads to TRU removal by multiple routes

MANAGEMENT OF TRANSURANIC (TRU) WASTE RETRIEVAL PROJECT RISKS SUCCESSES IN THE STARTUP OF THE HANFORD 200 AREA TRU WASTE RETRIEVAL PROJECT

International Nuclear Information System (INIS)

GREENWLL, R.D.

2005-01-01

A risk identification and mitigation method applied to the Transuranic (TRU) Waste Retrieval Project performed at the Hanford 200 Area burial grounds is described. Retrieval operations are analyzed using process flow diagramming. and the anticipated project contingencies are included in the Authorization Basis and operational plans. Examples of uncertainties assessed include degraded container integrity, bulged drums, unknown containers, and releases to the environment. Identification and mitigation of project risks contributed to the safe retrieval of over 1700 cubic meters of waste without significant work stoppage and below the targeted cost per cubic meter retrieved. This paper will be of interest to managers, project engineers, regulators, and others who are responsible for successful performance of waste retrieval and other projects with high safety and performance risks

Estimation of initial lung deposition of inhaled 238PuO2 in beagles

International Nuclear Information System (INIS)

Stevens, D.L.; Park, J.F.

1986-01-01

Studies to determine the life-span dose-effect relationship of inhaled 238 PuO 2 in dogs require an estimate of initial lung deposition (ILD) to calculate the radiation dose to several organs. Ideally, this estimate of ILD is obtained by a summation of plutonium body burden at death plus all the plutonium excreted during the life of the dog. However, the high costs of excreta collection and of plutonium analyses for all excreta from each dog made it necessary to approximate the ILD by other less expensive methods. These methods could introduce error into the estimate of ILD and, consequently, into the radiation dose calculation. The objective of this work was to evaluate the potential error for several methods of estimating ILD. Thirteen beagle dogs were given a single 5- to 30-min exposure to 238 PuO 2 aerosols, resulting in estimated ILD of 0.85 to 11.7 μCi of plutonium-238. Plutonium analyses of the tissues at death and of all excreta from these dogs were used for this evaluation. The estimate of ILD, obtained by summation of the plutonium body burden at death plus all the plutonium excreted, was compared to the estimated ILD obtained by the plutonium whole-body retention function for each dog, using all excreta data; the mean plutonium whole-body retention function for each dog, using all excreta data; the plutonium whole-body retention function for each dog, using partial excreta data; and a mean plutonium whole-body retention function for all dogs, using partial excreta data. 4 refs., 3 figs., 4 tabs

Fabrication of 238Pu based sources for energy micro-generator

International Nuclear Information System (INIS)

Barthelemy, Pierre; Boucher, Rene

1969-04-01

The authors describe the fabrication of sources of 238 Pu. The plutonium-scandium alloy is obtained by arc fusion in its delta phase. This alloy is chosen for its excellent malleability, and is rolled at 20 C. Pellets are then cut and decontaminated. Each pellet is then placed in a first tantalum sheath which is welded by electronic bombardment. A second sheath in platinum-iridium is placed around the first one, and also welded by using the same welding process. The so-fabricated sources are to feed energy thermal-electric conversion micro-generators which are supposed to operate tens of years in medical applications as organ stimulators [fr

238Pu based energy micro-generation sources for medical applications

International Nuclear Information System (INIS)

Boucher, Rene

1968-10-01

Pace-makers are frequently implanted in the human body. The existing apparatus are, actually, equipped with chemical piles with a lifetime of about 15 months. The use of 238 Pu will provide a pace-maker with an autonomy of 10 years at least. Principal problems of security due to the use of plutonium are considered. It is advisable to improve the properties of pure plutonium by small additions of elements such as cerium, scandium, indium, gallium or americium. A number of the most important properties for a pace-maker source are presented. Finally, the fabrication and canning of the source are surveyed. (author) [fr

Innovations in the Assay of Un-Segregated Multi-Isotopic Grade TRU Waste Boxes with SuperHENC and FRAM Technology

International Nuclear Information System (INIS)

Simpson, A. P.; Barber, S.; Abdurrahman, N. M.

2006-01-01

The Super High Efficiency Neutron Coincidence Counter (SuperHENC) was originally developed by BIL Solutions Inc., Los Alamos National Laboratory (LANL) and Rocky Flats Environmental Technology Site (RFETS) for assay of transuranic (TRU) waste in Standard Waste Boxes (SWB) at Rocky Flats. This mobile system was a key component in the shipment of over 4,000 SWBs to the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. The system was WIPP certified in 2001 and operated at the site for four years. The success of this system, a passive neutron coincidence counter combined with high resolution gamma spectroscopy, led to the order of two new units, delivered to Hanford in 2004. Several new challenges were faced at Hanford: For example, the original RFETS system was calibrated for segregated waste streams such that metals, plastics, wet combustibles and dry combustibles were separated by 'Item Description Codes' prior to assay. Furthermore, the RFETS mission of handling only weapons grade plutonium, enabled the original SuperHENC to benefit from the use of known Pu isotopics. Operations at Hanford, as with most other DOE sites, generate un-segregated waste streams, with a wide diversity of Pu isotopics. Consequently, the new SuperHENCs are required to deal with new technical challenges. The neutron system's software and calibration methodology have been modified to encompass these new requirements. In addition, PC-FRAM software has been added to the gamma system, providing a robust isotopic measurement capability. Finally a new software package has been developed that integrates the neutron and gamma data to provide a final assay results and analysis report. The new system's performance has been rigorously tested and validated against WIPP quality requirements. These modifications, together with the mobile platform, make the new SuperHENC far more versatile in handling diverse waste streams and allow for rapid redeployment around the DOE complex. (authors)

Thermal conductivity of 238PuO2 powder, intermediates, and dense fuel forms

International Nuclear Information System (INIS)

Bickford, D.F.; Crain, B. Jr.

1975-10-01

The thermal conductivities of porous 238 PuO 2 powder (calcined oxalate), milled powder, and high-density granules were calculated from direct measurements of steady-state temperature profiles resulting from self-heating. Thermal conductivities varied with density, temperature, and gas content of the pores. Errors caused by thermocouple heat conduction were less than 5 percent when the dimensions of the thermal conductivity cell and the thermocouple were properly selected

Routine radiochemical method for the determination of 90Sr, 238Pu, 239+240Pu, 241Am and 244Cm in environmental samples

International Nuclear Information System (INIS)

Ageyev, V.A.; Sajeniouk, A.D.

2005-01-01

Routine analytical procedures have been developed for the reliable simultaneous determination of 90 Sr, 238 Pu, 239+240 Pu, 241 Am and 242-244 Cm, Chernobyl derived radioisotopes and fallout after nuclear weapon tests in a wide range of environmental samples: soil (100-200 g), sediments, aerosols, water and vegetation. This procedure has been applied to thousands of soil and sediment samples and hundreds of biological and water samples taken in the exclusive zone of Chernobyl NPP and different regions of Ukraine from 1989 to the present. After the sample has been properly prepared and isotopic tracers added, plutonium, americium and curium are precipitated with calcium oxalate and then lanthanum fluoride. Plutonium is separated from americium and curium by anion-exchange. Americium and curium are separated from rare earths by cation-exchange with gradient elute α-hydroxy-iso-butyric acid. During projects by AQCS IAEA 'Evaluation of Methods for 90 Sr in a Mineral Matrix' and 'Proficiency Test for 239 Pu, 241 Pu and 241 Am Measurement in a Mineral Matrix' accuracy and precision for 90 Sr, 239 Pu and 241 Am by present procedure was evaluated. Advantages, difficulties and limitations of the method are discussed. (author)

Review on technical issues influencing the performance of chemical barriers of TRU waste repository

International Nuclear Information System (INIS)

Fujita, Tomonari; Sugiyama, Daisuke; Tsukamoto, Masaki; Yokoyama, Hayaichi

1997-01-01

Studies of technical issues influencing the performance assessment of TRU waste disposal which is occurred from the nuclear fuel reprocessing were reviewed in related to the development of safety analysis method. Especially, the chemical containment was investigated as a key barrier to radionuclide migration. TRU waste including long-lived radionuclides need long-term performance assessment which could be assumed only by the chemical barrier. The description of technical issues concerned with the performance of TRU waste repository has been divided into the following categories: long-term degradation of cementitious materials as engineered barrier for radionuclide migration, effect of colloids, organic macromolecules and organic degradation products on chemical behavior of radionuclides, gas generation by corrosion of metallic wastes, and effects of microbial activity. Preliminary performance assessment indicated that important factors affecting performance of chemical barriers in near-field were the distribution coefficient and the solubility of radionuclides in near-field groundwater. Therefore, it was identified that key issues associated with performance of chemical barrier were evaluation of (a) the long-term change of distribution coefficient of cementitious material through the degradation under repository condition and (b) chemical speciation change of radionuclides such as increase of solubility by the presence of colloidal-size materials. (author)

Progress report on nitric-phosphoric acid oxidation

International Nuclear Information System (INIS)

Pierce, R.A.

1994-01-01

The purpose of this program has been to demonstrate a nitric-phosphoric acid destruction technology which can treat a heterogeneous waste stream. This technology is being developed to convert hazardous liquid and solid organics to inorganic gases and salts while simultaneously performing a surface decontamination of the noncombustible items. Pu-238 waste is an issue because it must be shipped to WIPP. However, the presence of organics and Pu-238 waste is an issue because it must be shipped to WIPP. However, the presence of organics and Pu-238 exceeds packaging requirements because of concerns of hydrogen generation. If the TRU can be separated from the organics, the allowable heat load of a container increases a factor of 25. More importantly, since the current shipping package is limited by volume and not heat loading, destroying the organic compounds and decontaminating noncombustible can potentially create a three-order magnitude decrease in the number of shipments that must be made to WIPP. The process envisioned will be configured to handle 1 million pounds (as of 12/91) of a wide range of solid TRU-contaminated waste of which 600,000 pounds is combustible. The process will oxidize the combustibles (a mixture of 14% cellulose, 3% rubber, 64% plastics, 9% absorbed oil, 4% resins and sludges, and 6% miscellaneous organics) without requiring separation from the 400,000 pounds of noncombustibles. The system is being developed to operate below 200 C at moderate pressures (0--15 psig). This report primarily discusses results obtained over the past 3 1/2 months and their impact on the feasibility of a pilot-scale system

Research on safety evaluation for TRU waste disposal

International Nuclear Information System (INIS)

Senoo, M.; Shirahashi, K.; Sakamoto, Y.; Moriyama, N.; Konishi, M.

1989-01-01

Studies on adsorption behavior of transuranic (TRU) elements have been performed from the view point of validating the data for safety assessment and investigating adsorption behavior of TRU elements. Distribution coefficient (Kd value) of plutonium between groundwater and soils sampled at the planning site of low level waste disposal facility were measured for safety assessment. Kd values measured were the order of 10 3 ml/g. For investigating adsorption behavior, pH dependency of Kd value of neptunium and Am for soils were studied. It was concluded that pH dependency of Kd value of neptunium was mainly owing to amount of surface charge of soils, on the other hand that of Am was due to chemical form of Am. Influence of carbonation of cement for adsorption behavior of neptunium and plutonium was also investigated and it was concluded that Kd value of carbonated cement was lower than that of fresh cement

The determination of Pu-241 by liquid scintillation counting in liquid effluents of the Karlsruhe Nuclear Research Center

International Nuclear Information System (INIS)

Godoy, J.M.; Schuettelkopf, H.; Pimpl, M.

1983-04-01

A procedure was developed to measure Pu-241 by liquid scintillation counting. Sample preparation was performed by electroplating of plutonium on stainless steel planchets. To correct the selfabsorption, the linear dependence of counting efficiency in the liquid scintillation counter from the resolution in the alpha spectrometer was used. Pu-238, Pu-239+240 and Pu-241 were measured in the liquid effluents of the Karlsruhe Nuclear Research Center (KfK). The concentrations in monthly mixed samples ranged from 0.07 until 46 nCi Pu-238/m 3 , from 0.13 until 2.1 nCi Pu-239+240/m 3 and from 25 until 190 nCi Pu-241/m 3 . Between 5.4% and 41% of the plutonium content of the KfK waste water are released to the River Old Rhine. The values for the activity ratio Pu-238/Pu-239+240 are between 0.39 and 1.1 and for Pu-241/Pu-239+240 are between 11 and 300. The mean value for Pu-241/Pu-239+240 is 61. The dose exposure of the environmental population of the Karlsruhe Nuclear Research Center caused by released Pu-241 is negligible low. (orig./HP) [de

Toxicity of inhaled 238PuO2 in Beagle dogs: A. Monodisperse 1.5 μm AMAD particles. B. Monodisperse 3.0 μm particles. XV

International Nuclear Information System (INIS)

Mewhinney, J.A.; Gillett, N.A.; Muggenburg, B.A.; Hahn, F.F.; Diel, J.H.; Mauderly, J.L.; Boecker, B.B.; McClellan, R.O.

1988-01-01

Beagle dogs inhaled one of two sizes of monodisperse aerosols of 238 PuO 2 that resulted in graded levels of 238 Pu in the lung. All dogs are being studied for their life span. One hundred and thirty-seven dogs that had initial lung burdens ranging from 0.01 to 1.5 μCi 238 Pu/kg body weight (0.37 to 56 kBq/kg) have died, 8 with radiation pneumonitis and pulmonary fibrosis, 8 with lung tumors, 88 with bone tumors, 10 with liver tumors, and 25 of miscellaneous causes. Eighteen control dogs have died. Observations are being continued on 8 exposed and 6 control dogs alive at 4577-5274 days after exposure. (author)

Test Plan Addendum No. 1: Waste Isolation Pilot Plant bin-scale CH TRU waste tests

International Nuclear Information System (INIS)

Molecke, M.A.; Lappin, A.R.

1990-12-01

This document is the first major revision to the Test Plan: WIPP Bin-Scale CH TRU Waste Tests. Factors that make this revision necessary are described and justified in Section 1, and elaborated upon in Section 4. This addendum contains recommended estimates of, and details for: (1) The total separation of waste leaching/solubility tests from bin-scale gas tests, including preliminary details and quantities of leaching tests required for testing of Levels 1, 2, and 3 WIPP CH TRU wastes; (2) An initial description and quantification of bin-scale gas test Phase 0, added to provide a crucial tie to pretest waste characterization representatives and overall test statistical validation; (3) A revision to the number of test bins required for Phases 1 and 2 of the bin gas test program, and specification of the numbers of additional bin tests required for incorporating gas testing of Level 2 wastes into test Phase 3. Contingencies are stated for the total number of test bins required, both positive and negative, including the supporting assumptions, logic, and decision points. (4) Several other general test detail updates occurring since the Test Plan was approved and published in January, 1990. Possible impacts of recommended revisions included in this Addendum on WIPP site operations are called out and described. 56 refs., 12 tabs

PDP cycle 1 tests at INEL

Energy Technology Data Exchange (ETDEWEB)

Harker, Y.D.; Twedell, G.W. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

1997-11-01

The Idaho National Engineering Laboratory (INEL) is a participant in the nondestructive assay Performance Demonstration Program (PDP) as part of the U.S. TRU Waste Characterization Program. The PDP program was designed to help ensure compliance with the quality assurance objectives (QAO`s) in the TRU Waste Characterization Program Plan. In June, 1996, cycle 1 of PDP program was completed at the Stored Waste Examination Pilot Plant (SWEPP) at INEL. The assay capability at INEL/SWEPP consists of a passive active neutron (PAN) radioassay system (for bulk fissile material assay) and a passive gamma spectrometry system (for isotopic mass ratio determination). The results from the two systems are combined to produce a single assay report which contains isotopic information ({sup 238}Pu, {sup 239}Pu), density, total activity, alpha activity, TRU activity, TRU activity concentration, Pu equivalent Curies and fissile gram equivalent. The PDP cycle 1 tests were expected to test bias and precision of the assay systems under nearly ideal conditions; ie., non-interfering matrices and little or no source self shielding. The test consisted of two drums in which the source loading was not known by the site. One drum was essentially empty and the other was filled with ethafoam. As per PDP`s instructions, the tests were to be conducted using the same procedures and equipment that normally would be used by SWEPP to assay real waste drums. This paper will discuss the lessons learned from these tests and INEL`s plans to improve the capabilities of the SWEPP assay systems. 7 refs., 6 tabs.

Pu speciation in actual and simulated aged wastes

Energy Technology Data Exchange (ETDEWEB)

Lezama-pacheco, Juan S [Los Alamos National Laboratory; Conradson, Steven D [Los Alamos National Laboratory

2008-01-01

X-ray Absorption Fine Structure Spectroscopy (XAFS) at the Pu L{sub II/III} edge was used to determine the speciation of this element in (1) Hanford Z-9 Pu crib samples, (2) deteriorated waste resins from a chloride process ion-exchange purification line, and (3) the sediments from two Waste Isolation Pilot Plant Liter Scale simulant brine systems. The Pu speciation in all of these samples except one is within the range previously displayed by PuO{sub 2+x-2y}(OH){sub y}{center_dot}zH{sub 2}O compounds, which is expected based on the putative thermodynamic stability of this system for Pu equilibrated with excess H{sub 2}O and O{sub 2} under environmental conditions. The primary exception was a near neutral brine experiment that displayed evidence for partial substitution of the normal O-based ligands with Cl{sup -} and a concomitant expansion of the Pu-Pu distance relative to the much more highly ordered Pu near neighbor shell in PuO{sub 2}. However, although the Pu speciation was not necessarily unusual, the Pu chemistry identified via the history of these samples did exhibit unexpected patterns, the most significant of which may be that the presence of the Pu(V)-oxo species may decrease rather than increase the overall solubility of these compounds. Several additional aspects of the Pu speciation have also not been previously observed in laboratory-based samples. The molecular environmental chemistry of Pu is therefore likely to be more complicated than would be predicted based solely on the behavior of PuO{sub 2} under laboratory conditions.

Study on integrated TRU multi-recycling in sodium cooled fast reactor CDFR

International Nuclear Information System (INIS)

Hu Yun; Xu Mi; Wang Kan

2010-01-01

In view of recently proposed closed fuel cycle strategy which would recycle the integrated transuranics (TRU) from PWR spent fuel in the fast reactors, the neutronics characteristics of TRU recycled in China Demonstration Fast Reactor (CDFR) are studied in this paper. The results show that loading integrated TRU to substitute pure Pu as driver fuel will mainly make the influence on sodium void worth and negligible effects on other parameters, and hence TRU recycling in CDFR is feasible from viewpoint of core neutronics. If TRU is multi-recycled, the variation of TRU composition depends on fuel types and the ratio of TRU and U when recycling. It is indicated that, when TRU is multi-recycled in CDFR with MOX fuel, the minor actinides (MA) fraction in TRU will firstly decrease to ∼7.24% (minimum) within 8 TRU recycle times and then slowly increase to ∼7.7% after 20 TRU recycle times; while when TRU is multi-recycled in CDFR with metal fuel (TRU-U-10Zr), the MA fraction in TRU will gradually approach to an equilibrium state with the MA fraction of ∼3.8%, demonstrating better MA transmutation effect in metal fuel core. No matter 7.7 or 3.8%, they are both lower than ∼10% in PWR spent fuel with burnup of 45 GWd/tU, which presents satisfying effect of MA amount controlling for TRU multi-recycling strategy. On the other hand, the corresponding recycling parameters such as TRU heat release and neutron emission rate are also much lower in metal fuel than those in MOX fuel. Moreover, TRU recycled in metal fuel will bring greater fissile Pu isotopes equilibrium fraction due to better breeding capability of metal fuel. Finally, it could be summarized that integrated TRU multi-recycling in fast reactor can make contributions to both breeding and transmutation, and such strategy is a prospective closed fuel cycle manner to achieve the object of effective control of cumulated MA amount and sustainable development of nuclear energy.

The AS-76 interlaboratory experiment on the alpha spectrometric determination of Pu-238. Pt. 1

International Nuclear Information System (INIS)

Beyrich, W.; Spannagel, G.

1979-12-01

In cooperation with 26 laboratories of 11 countries or international organizations, the Safeguards Project of the Karlsruhe Nuclear Research Center carried out the interlaboratory program AS-76. It focused on the alpha-spectrometric determination of the Pu-238 isotope. The performance of the program as well as the results obtained are described. (orig.) 891 HP/orig. 892 MKO [de

Statistical analysis of radiochemical measurements of TRU radionuclides in REDC waste

International Nuclear Information System (INIS)

Beauchamp, J.; Downing, D.; Chapman, J.; Fedorov, V.; Nguyen, L.; Parks, C.; Schultz, F.; Yong, L.

1996-10-01

This report summarizes results of the study on the isotopic ratios of transuranium elements in waste from the Radiochemical Engineering Development Center actinide-processing streams. The knowledge of the isotopic ratios when combined with results of nondestructive assays, in particular with results of Active-Passive Neutron Examination Assay and Gamma Active Segmented Passive Assay, may lead to significant increase in precision of the determination of TRU elements contained in ORNL generated waste streams

Transuranic (TRU) Waste Repackaging at the Nevada Test Site

International Nuclear Information System (INIS)

Di Sanza, E.F.; Pyles, G.; Ciucci, J.; Arnold, P.

2009-01-01

This paper describes the activities required to modify a facility and the process of characterizing, repackaging, and preparing for shipment the Nevada Test Site's (NTS) legacy transuranic (TRU) waste in 58 oversize boxes (OSB). The waste, generated at other U.S. Department of Energy (DOE) sites and shipped to the NTS between 1974 and 1990, requires size-reduction for off-site shipment and disposal. The waste processing approach was tailored to reduce the volume of TRU waste by employing decontamination and non-destructive assay. As a result, the low-level waste (LLW) generated by this process was packaged, with minimal size reduction, in large sea-land containers for disposal at the NTS Area 5 Radioactive Waste Management Complex (RWMC). The remaining TRU waste was repackaged and sent to the Idaho National Laboratory Consolidation Site for additional characterization in preparation for disposal at the Waste Isolation Pilot Plant (WIPP), near Carlsbad, New Mexico. The DOE National Nuclear Security Administration Nevada Site Office and the NTS Management and Operating (M and O) contractor, NSTec, successfully partnered to modify and upgrade an existing facility, the Visual Examination and Repackaging Building (VERB). The VERB modifications, including a new ventilation system and modified containment structure, required an approved Preliminary Documented Safety Analysis prior to project procurement and construction. Upgrade of the VERB from a radiological facility to a Hazard Category 3 Nuclear Facility required new rigor in the design and construction areas and was executed on an aggressive schedule. The facility Documented Safety Analysis required that OSBs be vented prior to introduction into the VERB. Box venting was safely completed after developing and implementing two types of custom venting systems for the heavy gauge box construction. A remotely operated punching process was used on boxes with wall thickness of up to 3.05 mm (0.120 in) to insert aluminum

Classification of the Z-Pinch Waste Stream as Low-Level Waste for Disposal

Energy Technology Data Exchange (ETDEWEB)

Singledecker, Steven John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-03-10

The purpose of this document is to describe the waste stream from Z-Pinch Residual Waste Project that due to worker safety concerns and operational efficiency is a candidate for blending Transuranic and low level waste together and can be safely packaged as low-level waste consistent with DOE Order 435.1 requirements and NRC guidance 10 CFR 61.42. This waste stream consists of the Pu-ICE post-shot containment systems, including plutonium targets, generated from the Z Machine experiments requested by LANL and conducted by SNL/NM. In the past, this TRU waste was shipped back to LANL after Sandia sends the TRU data package to LANL to certify the characterization (by CCP), transport and disposition at WIPP (CBFO) per LANL MOU-0066. The Low Level Waste is managed, characterized, shipped and disposed of at NNSS by SNL/NM per Sandia MOU # 11-S-560.

Removal of 238Pu(IV) from mice by poly-catechoylate, -hydroxamate or -hydroxypyridinonate ligands

International Nuclear Information System (INIS)

Durbin, P.W.; Jeung, N.; Rodgers, S.J.; Turowski, P.N.; Weitl, F.L.; White, D.L.; Raymond, K.N.; California Univ., Berkeley, CA

1989-01-01

Binding of actinide (IV) by plasma proteins impedes excretion. Facilitation of elimination with chelating agents is the only known way to reduce carcinogenic risk. Iron-sequestering agents produced by micro-organisms contain metal-binding groups that bind Pu(IV) at pH 7.4 (catechol, CAM, in enterobactin; hydroxamate, X, in the ferrioaxamines; hydroxypyridinone, HOPO). Our synthetic ligands contain up to four such groups linked by alkyl chains or attached to desferrioxamine (DFO) or diethylene-triamine-pentaacetic acid (DPTA). 238 Pu excretion was tested in mice given 30 μmol.kg -1 of a ligand. Ligands that removed as much or more Pu than CaNa 3 -DTPA(≥70% of injected Pu(% ID)) are, in decreasing order of effectiveness: (1) Fe(III)-3,4,3-LIHOPO, (2) DFO-HOPO, (3) 3,4,3-LIHOPO, (4) 3,4,3-LICAM(C). Orally administered ligands 1-4, (5) 3,4,3-LICAM(S) and (6) ZnNa-DTPA-DX removed as much or more Pu than CaNa 3 -DTPA (≥ 15% ID). Ligands 1-4 and 6 injected 24 h after the Pu removed ≥ 5% ID more than control excretion (equivalent to or better than CaNa 3 -DTPA). All the new ligands at a dosage of 0.3 μmol.kg -1 removed a significant amount of Pu compared with controls: CaNa 3 -DTPA was ineffective. Ligand 3 is acutely toxic at high dosage, but the others appear to be of low toxicity. The HOPO ligands and ZnNa-DTPA-DX are recommended for further study. (author)

Determination of 240Pu/239Pu isotope ratios in Kara Sea and Novaya Zemlya sediments using accelerator mass spectrometry

International Nuclear Information System (INIS)

Oughton, D.H.; Skipperud, L.; Salbu, B.; Fifield, L.K.; Cresswell, R.C.; Day, J.P.

1999-01-01

Accelerator mass spectrometry (AMS) has been used to determine Pu activity concentrations and 240 Pu/ 239 Pu isotope ratios in sediments from the Kara Sea and radioactive waste dumping sites at Novaya Zemlya. Measured 239,240 Pu activities ranged from 0.06 - 9.8 Bq/kg dry weight, 240 Pu/ 239 Pu atom ratios ranged from 0.13 to 0.28, and 238 Pu/ 239,240 Pu activity ratios from 0.02 to 0.6. Perturbations from global fallout isotope ratios were evident at three sites: the Yenisey Estuary and Abrosimov Fjords where 240 Pu/ 239 Pu ratios were lower (0.13-0.14); and Stepovogo Fjord sediments where ratios were higher (up to 0.28) than fallout ratios. Based on procedural blanks, detection limits for AMS were below 1 fg Pu and the method showed good precision for isotope ratio measurements, minimal matrix, interference and memory effects. For high level samples, comparison between alpha spectrometry and AMS gave good agreement for measurement of 239,240 Pu activity concentrations. (author)

Deconvolution of ^238,239,240Pu conversion electron spectra measured with a silicon drift detector

DEFF Research Database (Denmark)

Pommé, S.; Marouli, M.; Paepen, J.

2018-01-01

Internal conversion electron (ICE) spectra of thin 238,239,240Pu sources, measured with a windowless Peltier-cooled silicon drift detector (SDD), were deconvoluted and relative ICE intensities were derived from the fitted peak areas. Corrections were made for energy dependence of the full...

Performance Demonstration Program Plan for Nondestructive Assay of Boxed Wastes for the TRU Waste Characterization Program

International Nuclear Information System (INIS)

2001-01-01

The Performance Demonstration Program (PDP) for nondestructive assay (NDA) consists of a series of tests to evaluate the capability for NDA of transuranic (TRU) waste throughout the Department of Energy (DOE) complex. Each test is termed a PDP cycle. These evaluation cycles provide an objective measure of the reliability of measurements obtained from NDA systems used to characterize the radiological constituents of TRU waste. The primary documents governing the conduct of the PDP are the Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WAC; DOE 1999a) and the Quality Assurance Program Document (QAPD; DOE 1999b). The WAC requires participation in the PDP; the PDP must comply with the QAPD and the WAC. The WAC contains technical and quality requirements for acceptable NDA. This plan implements the general requirements of the QAPD and applicable requirements of the WAC for the NDA PDP for boxed waste assay systems. Measurement facilities demonstrate acceptable performance by the successful testing of simulated waste containers according to the criteria set by this PDP Plan. Comparison among DOE measurement groups and commercial assay services is achieved by comparing the results of measurements on similar simulated waste containers reported by the different measurement facilities. These tests are used as an independent means to assess the performance of measurement groups regarding compliance with established quality assurance objectives (QAO's). Measurement facilities must analyze the simulated waste containers using the same procedures used for normal waste characterization activities. For the boxed waste PDP, a simulated waste container consists of a modified standard waste box (SWB) emplaced with radioactive standards and fabricated matrix inserts. An SWB is a waste box with ends designed specifically to fit the TRUPACT-II shipping container. SWB's will be used to package a substantial volume of the TRU waste for disposal. These PDP sample components

Safety analysis report: packages 238Pu oxide shipping cask (packaging of fissile and other radioactive materials). Final report

International Nuclear Information System (INIS)

Evans, J.E.; Gates, A.A.

1975-06-01

Plutonium-238 (as PuO 2 powder) is shipped in triple-container stainless steel shipping casks in compliance with ERDA Manual Chapter 0529 (ERDAM 0529), Safety Standards for the Packaging of Fissile and Other Radioactive Materials. (U.S.)

Status of microwave process development for RH-TRU [remote-handled transuranic] wastes at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

White, T.L.; Youngblood, E.L.; Berry, J.B.; Mattus, A.J.

1990-01-01

The Oak Ridge National Laboratory (ORNL) Waste Handling and Packaging Plant is developing a microwave process to reduce and solidify remote-handled transuranic (RH-TRU) liquids and sludges presently stored in large tanks at ORNL. Testing has recently begun on an in-drum microwave process using nonradioactive RH-TRU surrogates. The microwave process development effort has focused on an in-drum process to dry the RH-TRU liquids and sludges in the final storage container and then melt the salt residues to form a solid monolith. A 1/3-scale proprietary microwave applicator was designed, fabricated, and tested to demonstrate the essential features of the microwave design and to provide input into the design of the full-scale applicator. The microwave fields are uniform in one dimension to reduce the formation of hot spots on the microwaved wasteform. The final wasteform meets the waste acceptance criteria for the Waste Isolation Pilot Plant, a federal repository for defense transuranic wastes near Carlsbad, New Mexico. 7 refs., 1 fig., 1 tab

Performance Demonstration Program Plan for Nondestructive Assay of Drummed Wastes for the TRU Waste Characterization Program

International Nuclear Information System (INIS)

2005-01-01

The Performance Demonstration Program (PDP) for Nondestructive Assay (NDA) is a test program designed to yield data on measurement system capability to characterize drummed transuranic (TRU) waste generated throughout the Department of Energy (DOE) complex. The tests are conducted periodically and provide a mechanism for the independent and objective assessment of NDA system performance and capability relative to the radiological characterization objectives and criteria of the Office of Characterization and Transportation (OCT). The primary documents requiring an NDA PDP are the Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WAC), which requires annual characterization facility participation in the PDP, and the Quality Assurance Program Document (QAPD). This NDA PDP implements the general requirements of the QAPD and applicable requirements of the WAC. Measurement facilities must demonstrate acceptable radiological characterization performance through measurement of test samples comprised of pre-specified PDP matrix drum/radioactive source configurations. Measurement facilities are required to analyze the NDA PDP drum samples using the same procedures approved and implemented for routine operational waste characterization activities. The test samples provide an independent means to assess NDA measurement system performance and compliance per criteria delineated in the NDA PDP Plan. General inter-comparison of NDA measurement system performance among DOE measurement facilities and commercial NDA services can also be evaluated using measurement results on similar NDA PDP test samples. A PDP test sample consists of a 55-gallon matrix drum containing a waste matrix type representative of a particular category of the DOE waste inventory and nuclear material standards of known radionuclide and isotopic composition typical of DOE radioactive material. The PDP sample components are made available to participating measurement facilities as designated by the

Fission Product Yields for 14 MeV Neutrons on 235U, 238U and 239Pu

International Nuclear Information System (INIS)

Mac Innes, M.; Chadwick, M.B.; Kawano, T.

2011-01-01

We report cumulative fission product yields (FPY) measured at Los Alamos for 14 MeV neutrons on 235 U, 238 U and 239 Pu. The results are from historical measurements made in the 1950s–1970s, not previously available in the peer reviewed literature, although an early version of the data was reported in the Ford and Norris review. The results are compared with other measurements and with the ENDF/B-VI England and Rider evaluation. Compared to the Laurec (CEA) data and to ENDF/B-VI evaluation, good agreement is seen for 235 U and 238 U, but our FPYs are generally higher for 239 Pu. The reason for the higher plutonium FPYs compared to earlier Los Alamos assessments reported by Ford and Norris is that we update the measured values to use modern nuclear data, and in particular the 14 MeV 239 Pu fission cross section is now known to be 15–20% lower than the value assumed in the 1950s, and therefore our assessed number of fissions in the plutonium sample is correspondingly lower. Our results are in excellent agreement with absolute FPY measurements by Nethaway (1971), although Nethaway later renormalized his data down by 9% having hypothesized that he had a normalization error. The new ENDF/B-VII.1 14 MeV FPY evaluation is in good agreement with our data.

Photon-induced Fission Product Yield Measurements on 235U, 238U, and 239Pu

Science.gov (United States)

Krishichayan, Fnu; Bhike, M.; Tonchev, A. P.; Tornow, W.

2015-10-01

During the past three years, a TUNL-LANL-LLNL collaboration has provided data on the fission product yields (FPYs) from quasi-monoenergetic neutron-induced fission of 235U, 238U, and 239Pu at TUNL in the 0.5 to 15 MeV energy range. Recently, we have extended these experiments to photo-fission. We measured the yields of fission fragments ranging from 85Kr to 147Nd from the photo-fission of 235U, 238U, and 239Pu using 13-MeV mono-energetic photon beams at the HIGS facility at TUNL. First of its kind, this measurement will provide a unique platform to explore the effect of the incoming probe on the FPYs, i.e., photons vs. neutrons. A dual-fission ionization chamber was used to determine the number of fissions in the targets and these samples (along with Au monitor foils) were gamma-ray counted in the low-background counting facility at TUNL. Details of the experimental set-up and results will be presented and compared to the FPYs obtained from neutron-induced fission at the same excitation energy of the compound nucleus. Work supported in part by the NNSA-SSAA Grant No. DE-NA0001838.

NDA BATCH 2002-02

Energy Technology Data Exchange (ETDEWEB)

Lawrence Livermore National Laboratory

2009-12-09

QC sample results (daily background checks, 20-gram and 100-gram SGS drum checks) were within acceptable criteria established by WIPP's Quality Assurance Objectives for TRU Waste Characterization. Replicate runs were performed on 5 drums with IDs LL85101099TRU, LL85801147TRU, LL85801109TRU, LL85300999TRU and LL85500979TRU. All replicate measurement results are identical at the 95% confidence level as established by WIPP criteria. Note that the batch covered 5 weeks of SGS measurements from 23-Jan-2002 through 22-Feb-2002. Data packet for SGS Batch 2002-02 generated using gamma spectroscopy with the Pu Facility SGS unit is technically reasonable. All QC samples are in compliance with established control limits. The batch data packet has been reviewed for correctness, completeness, consistency and compliance with WIPP's Quality Assurance Objectives and determined to be acceptable. An Expert Review was performed on the data packet between 28-Feb-02 and 09-Jul-02 to check for potential U-235, Np-237 and Am-241 interferences and address drum cases where specific scan segments showed Se gamma ray transmissions for the 136-keV gamma to be below 0.1 %. Two drums in the batch showed Pu-238 at a relative mass ratio more than 2% of all the Pu isotopes.

Extraction chromatographic separation of Sr, Pu and Am in environmental samples

Energy Technology Data Exchange (ETDEWEB)

Sidhu, Rajdeep

2004-04-01

An accurate determination of radionuclides from various sources in the environment is essential for assessment of the potential hazards and suitable countermeasures both in case of an authorised release, accidents and routine surveillance. Due to the short range of alpha and beta radiation, the accurate determination of pure alpha and beta emitters must always include radiochemical separations to separate the analytes from the matrix and from other interfering stable and radioactive nuclides. Hence, the procedures used for their determination are usually tedious and involve several preconcentration and separation steps. This work deals with the determination of {sup 90}Sr, {sup 241}Am, {sup 238}Pu, {sup 239,240}Pu and {sup 244}Cm, whic some of the most important artificial radionuclides. Due to either absence or low yield of gamma radiation, a secure determination of low concentrations of all these nuclides requires a dedicated chemistry. Selective extraction chromatographic resins (TRU- and Sr-Resin) have been utilised to develop new procedures for the analyses of Pu, Am and Cm isotopes in seawater and both these and {sup 90}Sr in soil, sediment, urine and low-level liquid radioactive effluents. The proposed method for the analyses of Pu and Am in seawater offers a quick and secure mode for the determination of these radionuclides in marine waters. Combined pre-concentration of actinides and strontium (oxalate or phosphate precipitation) followed by dual column separation on TRU- and Sr-Resin significantly reduces the through put time and costs compared to traditional ion exchange and precipitation methods. The greatest gain in productivity and environmental friendliness is achieved in Sr separations using Sr-Resin instead of precipitations involving fuming nitric acid and oxalate, hydroxide, chromate and carbonate precipitations. (author)

Metabolic characteristics of an industrial 238PuO2 dust and its effects in rodent lungs

International Nuclear Information System (INIS)

Smith, H.; Stather, J.W.; James, A.C.; Stradling, G.N.

1980-01-01

The physical and biological properties of a 238 PuO 2 dust were examined in rodents following an accidental human contamination with a 238 PuO 2 dust. The rodents were exposed to a respirable fraction of the dust, either by direct intubation into the pulmonary region of the lung or by inhalation of an aerosolized suspension at two levels [i.e., 1.1 kBq and 7.3 kBq initial lung deposit (ILD)]. Groups of animals were studied for up to 600 days after exposure. In this period about 8% of the ILD was translocated to bone and liver. Approximately half the ILD was cleared with a half-time of about 20 days. Long-term retention of the remainder depended upon the ILD. At the low level the half-time of long-term retention was about 240 days; at the highest level it corresponded to over 1000 days. The difference in retention characteristics was related to the degree of fibrosis in lung tissue, which increased in severity according to the radiation dose

TRU waste processing comparison: slagging pyrolysis versus modified glassmaker

International Nuclear Information System (INIS)

Bonner, W.F.; Cox, N.D.; Hootman, H.E.; Nelson, D.C.; Pye, D.

1980-03-01

A task force was assembled to make a technical comparison of the expected performance of two processing systems potentially applicable for treating TRU waste at the Idaho National Engineering Laboratory. One system contained a slagging pyrolysis incinerator; the other a modified Penberthy Electromelt glassmaker. Although the glassmaker technology is essentially undeveloped, it was assumed that the glassmaker could eventually be modified to operate as a combined waste incinerator and melter; that is, to perform the same functions as a slagger. Using a decision analysis methodology to evaluate figures-of-merit, the task force found no significant difference in the performance of the two systems. Some areas for future R and D efforts are recommended for both types of incinerators

IMPROVEMENTS IN HANFORD TRANSURANIC (TRU) PROGRAM UTILIZING SYSTEMS MODELING AND ANALYSES

International Nuclear Information System (INIS)

UYTIOCO EM

2007-01-01

Hanford's Transuranic (TRU) Program is responsible for certifying contact-handled (CH) TRU waste and shipping the certified waste to the Waste Isolation Pilot Plant (WIPP). Hanford's CH TRU waste includes material that is in retrievable storage as well as above ground storage, and newly generated waste. Certifying a typical container entails retrieving and then characterizing it (Real-Time Radiography, Non-Destructive Assay, and Head Space Gas Sampling), validating records (data review and reconciliation), and designating the container for a payload. The certified payload is then shipped to WIPP. Systems modeling and analysis techniques were applied to Hanford's TRU Program to help streamline the certification process and increase shipping rates

Toxicity of inhaled {sup 238}PuO{sub 2} in Beagle dogs: A. Monodisperse 1.5 {mu}m AMAD particles. B. Monodisperse 3.0 {mu}m particles. XV

Energy Technology Data Exchange (ETDEWEB)

Mewhinney, J A; Gillett, N A; Muggenburg, B A; Hahn, F F; Diel, J H; Mauderly, J L; Boecker, B B; McClellan, R O

1988-12-01

Beagle dogs inhaled one of two sizes of monodisperse aerosols of {sup 238}PuO{sub 2} that resulted in graded levels of {sup 238}Pu in the lung. All dogs are being studied for their life span. One hundred and thirty-seven dogs that had initial lung burdens ranging from 0.01 to 1.5 {mu}Ci {sup 238}Pu/kg body weight (0.37 to 56 kBq/kg) have died, 8 with radiation pneumonitis and pulmonary fibrosis, 8 with lung tumors, 88 with bone tumors, 10 with liver tumors, and 25 of miscellaneous causes. Eighteen control dogs have died. Observations are being continued on 8 exposed and 6 control dogs alive at 4577-5274 days after exposure. (author)

Determination of the activity concentration of a 238 Pu solution by the defined solid angle method utilizing a novel dual diaphragm-detector assembly.

Science.gov (United States)

Aguiar, Julio C; Galiano, Eduardo; Arenillas, Pablo

2005-08-01

The activity concentration of a (238)Pu solution was measured by the determined solid angle method employing a novel dual diaphragm-detector assembly, which has been previously described. Due to the special requirements of the detector, a new type of source holder was developed, which consisted of sandwiching the radioisotope between two organic films called VYNS. It was experimentally demonstrated that the VYNS films do not absorb alpha particles, but reduce their energy by an average of 22 keV.A mean activity concentration for (238)Pu of 359.10+/-0.8 kBq/g was measured.

Determination of the activity concentration of a 238Pu solution by the defined solid angle method utilizing a novel dual diaphragm-detector assembly

International Nuclear Information System (INIS)

Aguiar, Julio C.; Galiano, Eduardo; Arenillas, Pablo

2005-01-01

The activity concentration of a 238 Pu solution was measured by the determined solid angle method employing a novel dual diaphragm-detector assembly, which has been previously described. Due to the special requirements of the detector, a new type of source holder was developed, which consisted of sandwiching the radioisotope between two organic films called VYNS. It was experimentally demonstrated that the VYNS films do not absorb α particles, but reduce their energy by an average of 22keV.A mean activity concentration for 238 Pu of 359.10+/-0.8kBq/g was measured

Performance Demonstration Program Plan for Nondestructive Assay of Drummed Wastes for the TRU Waste Characterization Program

International Nuclear Information System (INIS)

2009-01-01

Each testing and analytical facility performing waste characterization activities for the Waste Isolation Pilot Plant (WIPP) participates in the Performance Demonstration Program (PDP) to comply with the Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WAC) (DOE/WIPP-02-3122) and the Quality Assurance Program Document (QAPD) (CBFO-94-1012). The PDP serves as a quality control check for data generated in the characterization of waste destined for WIPP. Single blind audit samples are prepared and distributed to each of the facilities participating in the PDP. The PDP evaluates analyses of simulated headspace gases, constituents of the Resource Conservation and Recovery Act (RCRA), and transuranic (TRU) radionuclides using nondestructive assay (NDA) techniques.

Radiochemical methodologies applied to analytical characterization of low and intermediate level wastes from nuclear power plants

International Nuclear Information System (INIS)

Monteiro, Roberto Pellacani G.; Júnior, Aluísio Souza R.; Kastner, Geraldo F.; Temba, Eliane S.C.; Oliveira, Thiago C. de; Amaral, Ângela M.; Franco, Milton B.

2017-01-01

The aim of this work is to present radiochemical methodologies developed at CDTN/CNEN in order to answer a program for isotopic inventory of radioactive wastes from Brazilian Nuclear Power Plants. In this program some radionuclides, 3 H, 14 C, 55 Fe, 59 Ni, 63 Ni, 90 Sr, 93 Zr, 94 Nb, 99 Tc, 129 I, 235 U, 238 U, 238 Pu, 239 + 240 Pu, 241 Pu, 242 Pu, 241 Am, 242 Cm e 243 + 244 Cm, were determined in Low Level Wastes (LLW) and Intermediate Level Wastes (ILW) and a protocol of analytical methodologies based on radiochemical separation steps and spectrometric and nuclear techniques was established. (author)

National low-level waste management program radionuclide report series, Volume 15: Uranium-238

International Nuclear Information System (INIS)

Adams, J.P.

1995-09-01

This report, Volume 15 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of uranium-238 ( 238 U). The purpose of the National Low-Level Waste Management Program Radionuclide Report Series is to provide information to state representatives and developers of low-level radioactive waste disposal facilities about the radiological, chemical, and physical characteristics of selected radionuclides and their behavior in the waste disposal facility environment. This report also includes discussions about waste types and forms in which 238 U can be found, and 238 U behavior in the environment and in the human body

Separation of Pu from soil prior to determination by ICP-MS

International Nuclear Information System (INIS)

Nygren, U.; Baxter, D.C.

2002-01-01

In the determination of plutonium in environmental materials by ICP-MS, chemical separation is often needed to remove, e.g., heavy sample matrices and interference from UH + on m/z 239. This separation can be, and often is, performed in the same way as for alpha-spectrometric analysis. There are, however, somewhat different demands on separation for ICP-MS compared to alpha-spectrometry, but so far little has been published on the optimisation of separation procedures for plutonium determination by ICP-MS. This paper describes the development of a separation procedure especially suited for the determination of Pu by ICP-MS. Focus has been on parameters such as chemical yield of plutonium and decontamination from uranium, as well as time requirements and ease of performance. The separation of plutonium was performed using various resins, such as anion exchange resin and extraction chromatographic materials. The procedures were carried out on water spiked with 238 U and 240 Pu to concentrations of approximately 300 ppb and 50 ppt, respectively. The basic separation procedure was: 1. Adjustment of oxidation state for Pu 2. Loading on column 3. Rinsing using 4*5 free column volumes (FCVs) of load solution - if needed in combination with 1*5 FCVs of an other rinsing agent 4. Elution of Pu - if needed followed by evaporation and dissolution in a solution suitable for ICP-MS determination 5. Determination by high resolution ICP-MS The elution of plutonium was performed using various media, based on either reduction of Pu(IV) to Pu(III) or complex formation. The chemical yield of plutonium and the decontamination from uranium for various resin/elution combinations can be seen in Figs. 1 and 2. It was found that the most efficient separation procedure in terms of yield and uranium decontamination was the combination of two extraction chromatographic materials, UTEVA followed by TRU, and elution of Pu by 0.1 % 1-hydroxyethane-1,1-diphosphonic acid (HEDPA). In this procedure

MCNP Modeling Results for Location of Buried TRU Waste Drums

International Nuclear Information System (INIS)

Steinman, D K; Schweitzer, J S

2006-01-01

In the 1960's, fifty-five gallon drums of TRU waste were buried in shallow pits on remote U.S. Government facilities such as the Idaho National Engineering Laboratory (now split into the Idaho National Laboratory and the Idaho Completion Project [ICP]). Subsequently, it was decided to remove the drums and the material that was in them from the burial pits and send the material to the Waste Isolation Pilot Plant in New Mexico. Several technologies have been tried to locate the drums non-intrusively with enough precision to minimize the chance for material to be spread into the environment. One of these technologies is the placement of steel probe holes in the pits into which wireline logging probes can be lowered to measure properties and concentrations of material surrounding the probe holes for evidence of TRU material. There is also a concern that large quantities of volatile organic compounds (VOC) are also present that would contaminate the environment during removal. In 2001, the Idaho National Engineering and Environmental Laboratory (INEEL) built two pulsed neutron wireline logging tools to measure TRU and VOC around the probe holes. The tools are the Prompt Fission Neutron (PFN) and the Pulsed Neutron Gamma (PNG), respectively. They were tested experimentally in surrogate test holes in 2003. The work reported here estimates the performance of the tools using Monte-Carlo modelling prior to field deployment. A MCNP model was constructed by INEEL personnel. It was modified by the authors to assess the ability of the tools to predict quantitatively the position and concentration of TRU and VOC materials disposed around the probe holes. The model was used to simulate the tools scanning the probe holes vertically in five centimetre increments. A drum was included in the model that could be placed near the probe hole and at other locations out to forty-five centimetres from the probe-hole in five centimetre increments. Scans were performed with no chlorine in the

Multi-isotopic determination of plutonium (239Pu, 240Pu, 241Pu and 242Pu) in marine sediments using sector-field inductively coupled plasma mass spectrometry.

Science.gov (United States)

Donard, O F X; Bruneau, F; Moldovan, M; Garraud, H; Epov, V N; Boust, D

2007-03-28

Among the transuranic elements present in the environment, plutonium isotopes are mainly attached to particles, and therefore they present a great interest for the study and modelling of particle transport in the marine environment. Except in the close vicinity of industrial sources, plutonium concentration in marine sediments is very low (from 10(-4) ng kg(-1) for (241)Pu to 10 ng kg(-1) for (239)Pu), and therefore the measurement of (238)Pu, (239)Pu, (240)Pu, (241)Pu and (242)Pu in sediments at such concentration level requires the use of very sensitive techniques. Moreover, sediment matrix contains huge amounts of mineral species, uranium and organic substances that must be removed before the determination of plutonium isotopes. Hence, an efficient sample preparation step is necessary prior to analysis. Within this work, a chemical procedure for the extraction, purification and pre-concentration of plutonium from marine sediments prior to sector-field inductively coupled plasma mass spectrometry (SF-ICP-MS) analysis has been optimized. The analytical method developed yields a pre-concentrated solution of plutonium from which (238)U and (241)Am have been removed, and which is suitable for the direct and simultaneous measurement of (239)Pu, (240)Pu, (241)Pu and (242)Pu by SF-ICP-MS.

The removal of inhaled 239Pu and 238Pu from beagle dogs by lung lavage and chelation treatment

International Nuclear Information System (INIS)

Muggenburg, B.A.; Mewhinney, J.A.; Miglio, J.J.; Slauson, D.O.; McClellan, R.O.

1976-01-01

Studies were conducted in beagle dogs to determine the efficiency of treatment by lung lavage and injections of chelating agents in removing inhaled plutonium of varied chemical forms and particle sizes. Polydisperse aerosols of 239 Pu were produced at different temperatures from 325 0 C to 1150 0 C to evaluate the effect of the chemical form of the particles. Aerosols of 238 Pu were produced at 1150 0 C only but were of different particle size or size distributions. Three dogs that inhaled each different plutonium aerosol were treated by lung lavages starting two days after the exposure. Subsequent lavages were performed on days 7, 10, 14, 21, 28, 35, 42, and 49 after exposure. Intravenous injections of 100 mg of diethylenetriaminepentaacetic acid (DTPA) as the calcium salt were given on days 1, 2, 3 and 4 after exposure and twice weekly thereafter to the time of sacrifice, 56 days after exposure. The 10 lung lavages removed from 18 to 49% of the initial lung burden of plutonium. The recovery of plutonium by lavage was similar irrespective of the temperature at which the aerosol was produced, however, lavage recovery decreased somewhat with increasing particle size. The efficacy of DTPA treatment increased with decreasing production temperature of the 239 Pu. Treatment with DTPA was not affected by particle size of the 0.8- and 1.9-μm monodisperse 239 Pu aerosol. The effectiveness of lung lavage decreased as the solubility of the aerosol particles increased whereas the effectiveness of the DTPA treatment increased as the solubility of the inhaled aerosol increased as shown by the lowest temperature aerosol and the aerosol-containing soluble fraction. These findings correlated qualitatively with a 2-hour in-vitro solubility test on the exposure aerosols. (author)

Neutron induced fission cross sections for 232Th, 235,238U, 237Np, and 239Pu

International Nuclear Information System (INIS)

Lisowski, P.W.; Ullmann, J.L.; Balestrini, S.J.; Hill, N.W.; Carlson, A.D.; Wasson, O.A.

1989-01-01

Neutron-induced fission cross section ratios for samples of 232 Th, 235,238 U, 237 Np and 239 Pu have been measured from 1 to 400 MeV. The fission reaction rate was determined for all samples simultaneously using a fast parallel plate ionization chamber at a 20-m flight path. A well characterized annular proton recoil telescope was used to measure the neutron fluence from 3 to 30 MeV. Those data provided the shape of the 235 U(n,f) cross section relative to the hydrogen scattering cross section. That shape was then normalized to the very accurately known value for 235 U(n,f) at 14.178 MeV. From 30 to 400 MeV cross section values were determined using the neutron fluence measured with a plastic scintillator. Cross section values of 232 Th, 235,238 U, 237 Np and 239 Pu were computed from the ratio data using the authors' values for 235 U(n,f). In addition to providing new results at high neutron energies, these data highlight several areas of deficiency in the evaluated nuclear data files and provide new information for the 235 U(n,f) standard

Resonance Region Covariance Analysis Method and New Covariance Data for Th-232, U-233, U-235, U-238, and Pu-239

International Nuclear Information System (INIS)

Leal, Luiz C.; Arbanas, Goran; Derrien, Herve; Wiarda, Dorothea

2008-01-01

Resonance-parameter covariance matrix (RPCM) evaluations in the resolved resonance region were done for 232Th, 233U, 235U, 238U, and 239Pu using the computer code SAMMY. The retroactive approach of the code SAMMY was used to generate the RPCMs for 233U, 235U. RPCMs for 232Th, 238U and 239Pu were generated together with the resonance parameter evaluations. The RPCMs were then converted in the ENDF format using the FILE32 representation. Alternatively, for computer storage reasons, the FILE32 was converted in the FILE33 cross section covariance matrix (CSCM). Both representations were processed using the computer code PUFF-IV. This paper describes the procedures used to generate the RPCM with SAMMY.

The field migration tests of 237Np, 238Pu, 241Am and 90Sr in aerated loess, aquifer and engineering barrier materials

International Nuclear Information System (INIS)

Li Shushen; Wang Zhiming; Zhao Yingjie; Fan Zhiwen; Liu Chunli; An Yongfeng; Yang Yue'e; Wu Qinghua

2003-01-01

This paper introduces the field migration tests of 237 Np, 238 Pu, 241 Am and 90 Sr in aerated loess, aquifer and engineering barrier materials. The tests in the aerated loess and engineering barrier materials were carried out under both natural and artificial sprinkling (15 mm/d) conditions. The tests in aquifer were carried out in both assemblies packed with undisturbed aquifer media and a definite undisturbed area. The results indicate that after 3 years tests no significant migrations were seen for all nuclides in engineering barrier materials under two kinds of conditions and in aerated loess under natural conditions. For the aerated loess under artificial sprinkling conditions, 2.7 cm (center of mass) migration in the area directly below the sand tracer layer (named as area 1) and 13 cm (peak) migration in the area outside the area 1 for 90 Sr were observed; There was no migration for 237 Np, 238 Pu and 241 Am. It was discovered that the sand layer used as carrier of nuclide tracer has barrier effect on unsaturated water and an influence on nuclide migration. This has been demonstrated by the inter comparison experiment with both sand and loess as tracer carrier. In the tracer tests of undisturbed aquifer area there was no significant migration of 237 Np, 238 Pu, 241 Am and 90 Sr after 1023 days. In the assembly 8 there was no significant migration for 238 Pu and 241 Am and a small backward migration 0.95 cm for 237 Np and 4.7 cm migration (center of mass) for 90 Sr were observed. The tests also indicate that there is no significant difference of nuclide migration in ordinary and degraded cement

ANALYSIS OF SPECIAL WASTE CONFIGURATIONS AT THE SRS WASTE MANAGEMENT FACILITIES

International Nuclear Information System (INIS)

Casella, V; Raymond Dewberry, R

2007-01-01

Job Control Waste (JCW) at the Savannah River Site (SRS) Solid Waste Management Facilities (SWMF) may be disposed of in special containers, and the analysis of these containers requires developing specific analysis methodologies. A method has been developed for the routine assay of prohibited items (liquids, etc.) contained in a 30-gallon drum that is then placed into a 55-gallon drum. Method development consisted of system calibration with a NIST standard at various drum-to-detector distances, method verification with a liquid sample containing a known amount of Pu-238, and modeling the inner container using Ortec Isotopic software. Using this method for measurement of the known standard in the drum-in-drum configuration produced excellent agreement (within 15%) with the known value. Savannah River Site Solid Waste Management also requested analysis of waste contained in large black boxes (commonly 18-feet x 12-feet x 7-feet) stored at the SWMF. These boxes are frequently stored in high background areas and background radiation must be considered for each analysis. A detection limit of less than 150 fissile-gram-equivalents (FGE) of TRU waste is required for the black-box analyses. There is usually excellent agreement for the measurements at different distances and measurement uncertainties of about 50% are obtained at distances of at least twenty feet from the box. This paper discusses the experimental setup, analysis and data evaluation for drum-in-drum and black box waste configurations at SRS

Determination of the activity concentration of a {sup 238}Pu solution by the defined solid angle method utilizing a novel dual diaphragm-detector assembly

Energy Technology Data Exchange (ETDEWEB)

Aguiar, Julio C. [Departamento de Postgrado, Universidad Tecnologica Nacional, Buenos Aires (Argentina); Galiano, Eduardo [Departament of Physics, Laurentian University, Sudbury, Ont. P3E 2C6 (Canada)]. E-mail: egalianoriveros@laurentian.ca; Arenillas, Pablo [Comision Nacional de Energia Atomica, CAE, Laboratorio de Metrologia de Radioisotopos, Buenos Aires (Argentina)

2005-08-01

The activity concentration of a {sup 238}Pu solution was measured by the determined solid angle method employing a novel dual diaphragm-detector assembly, which has been previously described. Due to the special requirements of the detector, a new type of source holder was developed, which consisted of sandwiching the radioisotope between two organic films called VYNS. It was experimentally demonstrated that the VYNS films do not absorb {alpha} particles, but reduce their energy by an average of 22keV.A mean activity concentration for {sup 238}Pu of 359.10+/-0.8kBq/g was measured.

Sequential determination of natural ({sup 232}Th, {sup 238}U) and anthropogenic ({sup 137}Cs, {sup 90}Sr, {sup 241}Am, {sup 239+240}Pu) radionuclides in environmental matrix

Energy Technology Data Exchange (ETDEWEB)

Michel, H.; Levent, D.; Barci, V.; Barci-Funel, G.; Hurel, C. [Laboratoire de Radiochimie, Sciences Analytiques et Environnement (LRSAE), Universite de Nice Sophia-Antipolis 06108 Nice Cedex (France)

2008-07-01

A new sequential method for the determination of both natural (U, Th) and anthropogenic (Sr, Cs, Pu, Am) radionuclides has been developed for application to soil and sediment samples. The procedure was optimised using a reference sediment (IAEA-368) and reference soils (IAEA-375 and IAEA-326). Reference materials were first digested using acids (leaching), 'total' acids on hot plate, and acids in microwave in order to compare the different digestion technique. Then, the separation and purification were made by anion exchange resin and selective extraction chromatography: Transuranic (TRU) and Strontium (SR) resins. Natural and anthropogenic alpha radionuclides were separated by Uranium and Tetravalent Actinide (UTEVA) resin, considering different acid elution medium. Finally, alpha and gamma semiconductor spectrometer and liquid scintillation spectrometer were used to measure radionuclide activities. The results obtained for strontium-90, cesium-137, thorium-232, uranium- 238, plutonium-239+240 and americium-241 isotopes by the proposed method for the reference materials provided excellent agreement with the recommended values and good chemical recoveries. (authors)

Interaction of a 238Pu fueled-sphere assembly with a simulated terrestrial environment

International Nuclear Information System (INIS)

Steinkruger, F.J.; Patterson, J.H.; Herrera, B.; Nelson, G.B.; Matlack, G.M.; Waterbury, G.R.; Pavone, D.

1981-02-01

A 238 Pu fueled sphere assembly (FSA) was exposed to a simulated humid environment on sandy soil for 3 y. After a 70-week exposure, plutonium was first detected in measurable quantities in rain and condensate samples. A core sample taken in the ninety-third week contained 302 ng of plutonium. Examination of the FSA after exposure revealed a hole in the bottom of the graphite impact shell (GIS) and a leaking weld on the vent assembly of the postimpact containment shell (PICS). These two openings may be the pathways for plutonium entry into the environment from the FSA

TRUEX process: a new dimension in management of liquid TRU wastes

International Nuclear Information System (INIS)

Schulz, W.W.; Horwitz, E.P.

1986-01-01

The TRUEX process is one of the, if not the, most exciting and potentially useful nuclear separations processes to be developed since the PUREX process was developed and applied in the 1950s. Attesting to its potential widespread use, Rockwell Hanford and ANL investigators, in a joint effort, are developing and testing TRUEX process flow sheets for removal of TRU elements from several Hanford Site wastes including the Plutonium Finishing Plant and complexed concentrate wastes. The TRUEX process also appears to be well suited to removal of plutonium and Am from aqueous chloride wastes generated during plutonium processing operations at the Los Alamos National Lab. (LANL); collaborative efforts between LANL and ANL scientists to develop and demonstrate TRUEX process flow sheets for treatment of LANL site chloride wastes are currently under way

Some physico-chemical and radiation properties of plutonium-238 metal prepared by electrochemical amalgamation

Energy Technology Data Exchange (ETDEWEB)

Peretrukhin, V.F. [A.N. Frumkin Institute of Physical Chemistry and Electrochemistry, Russian Academy of Sciences, 31 Leninsky Prospect, Moscow 119991 (Russian Federation)], E-mail: vperet@ipc.rssi.ru; Rovny, S.I. [Production Association ' Mayak' , 31 Prospect Lenin, Ozersk, Chelyabinsk Region 456784 (Russian Federation); Maslennikov, A.G. [A.N. Frumkin Institute of Physical Chemistry and Electrochemistry, Russian Academy of Sciences, 31 Leninsky Prospect, Moscow 119991 (Russian Federation); Ershov, V.V.; Chinenov, P.P.; Kapitonov, V.I.; Kuvaev, V.L. [Production Association ' Mayak' , 31 Prospect Lenin, Ozersk, Chelyabinsk Region 456784 (Russian Federation)

2007-10-11

Pu-238 metal was prepared by electrolytic amalgamation from Pu(III) acetate aqueous solution and by followed by the thermal decomposition of the Pu amalgam. The density, specific heat power, {gamma}-spectra, neutron flux, and corrosion kinetics in dry air at ambient temperature of the prepared {sup 238}Pu metal were measured. The neutron flux and {gamma}-spectra from {sup 238}Pu metal have been attributed to spontaneous and induced fission and to ({alpha},{alpha}'{gamma}), ({alpha},p{gamma}), and ({alpha},n{gamma}) nuclear reactions on light nuclei. The electrochemically prepared {sup 238}Pu metal was shown to generate fewer neutrons, produce less gamma radiation, and contains lower {sup 10}B, {sup 19}F, and {sup 28}Si impurities in comparison with biomedical {sup 238}PuO{sub 2}. The increase of neutron flux from the sample due to the reaction {sup 18}O({alpha},n{gamma}) {sup 21}Ne was shown to be proportional to the increase of the mass of the {sup 238}Pu metal with time due to corrosion in dry air. {sup 238}Pu metal corrosion rate maximum and average values (1.1 x 10{sup -2} and 4.7 x 10{sup -3} mg cm{sup -2} h{sup -1}, respectively) obtained in dry air were an order of magnitude higher than the rates published for {sup 239}Pu under similar experiment conditions. The difference between the {sup 239}Pu and {sup 238}Pu metal corrosion rate and mechanism is proposed to be due to the greater radiation effects and temperature on the {sup 238}Pu surface.

Demonstration of Entrained Solids and Sr/TRU Removal Processes with Archived AN-107 Waste

International Nuclear Information System (INIS)

Hallen, R.T.; Brooks, K.P.; Jagoda, L.K.

2000-01-01

Archived AN-107 waste was used to evaluate entrained solids removal, Sr/TRU decontamination of supernatant, and Sr/TRU solids removal. Even though most of the entrained solids had been previously removed from the archived sample, the residual entrained solids rapidly fouled the filter element resulting in very poor filter performance. An attempt to run at higher pressure resulted in more fouling, and reduced filter performance. Filtration efforts to remove entrained solids were abandoned and the waste was treated for Sr/TRU removal with the entrained solids present. The new processing scheme for Sr/TRU removal involving precipitation by added strontium and permanganate worked well. The decontamination factors for Sr and TRU components were significantly greater than the ILAW DF requirements for higher reagent concentrations of 1M hydroxide, 0.075M Sr, and 0.05M permanganate and lower reagent concentrations of 0.8M hydroxide, 0.05M Sr, and 0.03M permanganate. These results support the use of lower concentration of reagent additions in future tests. Optimization studies should be conducted to examine the reduction in added hydroxide from 1M to 0.5 M, reduction of Sr from 0.075M to 0.05M, and reduction in permanganate from 0.05M to 0.03M and the impact this reduction has on filtration performance with new samples from Tank AN-107. The combined entrained solids and Sr/TRU precipitate were successfully filtered in the single element, crossflow filtration unit. The filtrate flux was high, >0.1 gpm/ft 2 , at the initial test conditions of 53 psi and 11.2ft/s for the treated archived AN-107 sample. The filter flux rate dropped significantly with time as testing progressed and appears to be a result of shearing the agglomerated solids and fouling of the filter element by the resulting fine particles. The relatively low clean water flux rates obtained at the end of the test also indicate filter fouling. Chemical cleaning was required to restore clean water flux rates to pre

EXAMPLE OF A RISK-BASED DISPOSAL APPROVAL: SOLIDIFICATION OF HANFORD SITE TRANSURANIC (TRU) WASTE

International Nuclear Information System (INIS)

PRIGNANO AL

2007-01-01

The Hanford Site requested, and the U.S. Environmental Protection Agency (EPA) Region 10 approved, a Toxic Substances Control Act of 1976 (TSCA) risk-based disposal approval (RBDA) for solidifying approximately four cubic meters of waste from a specific area of one of the K East Basin: the North Loadout Pit (NLOP). The NLOP waste is a highly radioactive sludge that contained polychlorinated biphenyls (PCBs) regulated under TSCA. The prescribed disposal method for liquid PCB waste under TSCA regulations is either thermal treatment or decontamination. Due to the radioactive nature of the waste, however, neither thermal treatment nor decontamination was a viable option. As a result, the proposed treatment consisted of solidifying the material to comply with waste acceptance criteria at the Waste Isolation Pilot Plant (WPP) in Carlsbad, New Mexico, or possibly the Environmental Restoration Disposal Facility at the Hanford Site, depending on the resulting transuranic (TRU) content of the stabilized waste. The RBDA evaluated environmental risks associated with potential airborne PCBs. In addition, the RBDA made use of waste management controls already in place at the treatment unit. The treatment unit, the T Plant Complex, is a Resource Conservation and Recovery Act of 1976 (RCRA)-permitted facility used for storing and treating radioactive waste. The EPA found that the proposed activities did not pose an unreasonable risk to human health or the environment. Treatment took place from October 26,2005 to June 9,2006, and 332 208-liter (55-gallon) containers of solidified waste were produced. All treated drums assayed to date are TRU and will be disposed at WIPP

Results of 90Sr and 239+240Pu, 238Pu, 241Am measurements in some samples of mushrooms and forest soil from Poland

International Nuclear Information System (INIS)

Mietelski, J.W.; Larosa, J.; Ghods, A.

1992-01-01

Strontium-90, plutonium and americium activity concentrations in a few samples of forest soils, some species of mushrooms and fern leaves were determined. These results are compared with caesium activity concentrations in the same materials obtained in a previous work. Radiochemical procedures are described. The origin of the contamination (Chernobyl accident or nuclear test explosion release) is discussed. The 90 Sr activity concentration ranges from 0.6 Bq/kg (mushroom samples) to 48.4 Bq/kg (fern leaves). For 239+240 Pu, it ranges from not detected above background (mushrooms, fern) to 10.8 Bq/kg (humus layer of forest soil). The maximum concentration of 241 Am is found to be 2.4 Bq/kg (humus sample) and for 238 Pu it is 0.85 Bq/kg (also in the humus sample). (author). 12 refs, 9 figs, 7 tabs

U, Pu, and Am nuclear signatures of the Thule hydrogen bomb debris

DEFF Research Database (Denmark)

Eriksson, Mats; Lindahl, Patric; Roos, Per

2008-01-01

). In the five hot particles examined, the measured uranium atomic ratio was U-235/U-238 = 1.02 +/- 0.16 and the Pu-isotopic ratios were as follows: Pu-240/Pu-239 0.0551 +/- 0.0008 (atom ratio), Pu-238/Pu239+240 = 0.0161 +/- 0.0005 (activity ratio), Pu-241/Pu239+240 = 0.87 +/- 0.12 (activity ratio), and Am-241...... than one Pu source involved in the accident, confirming earlier studies. The Pu-238/Pu239+240 activity ratio and the Pu-240/Pu-239 atomic ratio were divided into at least two Pu-isotopic ratio groups. For both Pu-isotopic ratios, one ratio group had identical ratios as the five hot particles described...... above and for the other groups the Pu isotopic ratios were lower (Pu-238/Pu239+240 activity ratio similar to 0.01 and the Pu-240/Pu-239 atomic ratio 0.03). On the studied particles we observed that the U/Pu ratio decreased as a function of the time these particles were present in the sediment. We...

The fundamental study for Y2O3 stabilized ZrO2 containing simulated TRU

International Nuclear Information System (INIS)

Kuramoto, Ken-ichi; Kamizono, Hiroshi; Hayakawa, Issei; Muraoka, Susumu; Yanagi, Tadashi.

1991-06-01

Borosilicate glass waste form is considered to be the most suitable material for the immobilization of high-level nuclear waste (HLW). However when the salt-free process on Purex method is adopted and the group partitioning technique of HLW is completely developed, ceramic waste forms which are excellent in thermal stability seem better for the immobilization of hazardous TRU elements. This work is a fundamental study on the solidification of TRU with Y 2 O 3 -stabilized ZrO 2 . In this work, Ce and Nd were used as substitutes for Pu and Am or Cm. TZ-8Y (submicron powder) and designed Ce(NO 3 ) 3 or Nd(NO 3 ) 3 solution were mixed into paste. After dried, the paste was pelletized by the rubber press, and then sintered at 1400degC for 16h. Densities of the sintered pellets were measured and their microstructure was observed by X-ray diffraction and scanning electron microscopy. The results showed that (1) the relative density of ceramic pellet sample was as high as 96.4%, (2) each element was distributed homogeneously and only cubic phase existed. From leach tests in nitric acid and distilled water at 150degC, those ceramic pellet samples showed aqueous corrosion rates which were about 10 2 to 10 3 times lower than that of a glass waste form(PO500). (author)

On uncertainties and fluctuations of averaged neutron cross sections in unresolved resonance energy region for 235U, 238U, 239Pu

International Nuclear Information System (INIS)

Van'kov, A.A.; Blokhin, A.I.; Manokhin, V.N.; Kravchenko, I.V.

1985-01-01

This paper analyses the reasons for the differences which exist between group-averaged evaluated cross-section data from different evaluated data files for U235, U238 and Pu239 in the unresolved resonance energy region. (author)

Report of conceptual design for TRU solid waste facilities adjacent to 200H Area: Savannah River Plant

International Nuclear Information System (INIS)

1978-02-01

Facilities for consolidating Savannah River Plant solid transuranic (TRU) waste and placing in long-term safe, retrievable storage have been designed conceptually. A venture guidance appraisal of cost for the facilities has been prepared. The proposed site of the new processing area is adjacent to existing H Area facilities. The scopes of work comprising the conceptual design describe facilities for: exhuming high-level TRU waste from buried and pad-stored locations in the plant burial ground; opening, emptying, and sorting waste containers and their contents within shielded, regulated enclosures; volume-reducing the noncombustibles by physical processes and decontaminating the metal waste; burning combustibles; fixing the consolidated waste forms in a concrete matrix within a double-walled steel container; placing product containers in a retrievable surface storage facility adjacent to the existing plant burial ground; and maintaining accountability of all special nuclear materials. Processing, administration, and auxiliary service buildings are to be located adjacent to existing H Area facilities where certain power and waste liquid services will be shared

The effect of chronic exposure to 238Pu(IV) citrate on the embryonic development of carp and fathead minnow eggs

International Nuclear Information System (INIS)

Till, J.E.

1978-01-01

This study focused on the effects of plutonium to the developing fish egg. A quantitative analysis of the uptake of 238 Pu(IV) citrate by carp eggs indicated that plutonium is accumulated in the egg and reaches a concentration factor of approx 4 at hatching (72hr after exposure begins). Autoradiographs made from carp eggs that had been exposed to 238 Pu revealed that, although some plutonium was concentrated on the egg chorion, plutonium that penetrated the chorion was uniformly distri-buted throughout the perivitelline fluid, embryo and yolk sac. Using the uptake data for carp eggs, dose conversion factors were calculated for both carp eggs and fathead minnow eggs exposed to 238 Pu during embryological development. These values were 2100 rad/μCi/ml and 7500 rad/μCi/ml for carp and fathead minnows, respectively. Experiments were conducted in which both carp and fathead minnow eggs were exposed to plutonium in solution during embryogenesis; the percentage of eggs hatching, the number of abnormal larvae produced, and the survival of larvae were used as indicators of radiation toxicity. Concentrations in excess of 1 μCi/ml were required to prevent both species of eggs from hatching. It is concluded that fish eggs developing in natural aquatic ecosystems contaminated with plutonium probably do not receive a significant dose from the plutonium alpha radioactivity. Future analysis of fecundity and the production of abnormalities in the offspring of larvae exposed during embryological development would provide an additional degree of sensitivity to the toxicity test system used in this study. (author)

Interaction of 238PuO2 heat sources with terrestrial and aquatic environments

International Nuclear Information System (INIS)

Patterson, J.H.; Nelson, G.B.; Matlack, G.M.; Waterbury, G.R.

1975-01-01

Radioisotope thermoelectric generators used in space missions are designed with a great factor of safety to ensure that they will withstand reentry from orbit and impact with the earth, and safely contain the nuclear fuel until it is recovered. Existing designs, utilizing 238 PuO 2 fuel, have proved more than adequately safe. More data about the interaction of this material with terrestrial and aquatic environments is continually being sought to predict the behavior of these heat sources in the extremely unlikely contact of these materials with the land or ocean. Terrestrial environments are simulated with large environmental chambers that permit control of temperature, humidity, and rainfall using different kinds of soils. Rain falling on thermally hot chunks of 238 PuO 2 causes the spallation of the surface of the fuel into extremely fine particles, as small as 50 nm, that are later transported downward through the soil. Some of the plutonia particles become agglomerated with soil particles. Plutonium transport is more significant during winter than during summer because evaporation losses from the soil are less in winter. Aquatic environments are simulated with large aquaria that provide temperature and aeration control. Earlier fuel designs that employed a plutonia-molybdenum cermet showed plutonium release rates of about 10 μCi/m 2 - s, referred to the total surface area of the cermet. Present advanced fuels, employing pure plutonium oxide, show release rates of about 20 nCi/m 2 - s in seawater and about 150 nCi/m 2 - s in freshwater. The temperature of these more advanced heat sources does not seem to affect the release rate in seawater. (auth)

Minimization of the volume and Pu content of the waste generated at a plutonium fuel fabrication plant

International Nuclear Information System (INIS)

Pauwels, H.

1992-01-01

The amounts of waste generated during 1987, 1989 and a past reference period have been reported in great detail. The main conclusions which can be drawn from these figures are: (i) for all kinds of waste, the waste-to-product ratio has decreased very substantially during the past few years. This reduction results partly from a scale effect, i.e. the better load factor of the plant, and partly from Belgonucleare's continuous effort to minimize the radioactive waste arisings; (ii) the ratio of the Pu content of the waste to the total Pu throughput of the plant has also decreased substantially; (iii) the mean Pu content of the solid Pu contaminated waste equals 1.39 g Pu per unit volume of 25 l. Only for a small fraction of this waste (<5% by volume) does the Pu content exceed 5 g per unit volume of 25 l; (iv) even after the implementation of waste reducing measures, some 45% of the solid Pu contaminated waste is generated by operations which involve the handling and transfer of powders. Finally, some 63% of the total amount of Pu in the waste can be imputed to these operations

Plutonium 238/239 Decorporation Model

Science.gov (United States)

2014-10-01

4. Transfer Coefficients for the DTPA Biokinetic Model (Breustedt 2009) ...................... 25 Table 5. Decay Properties of Pu-238 and Pu-239...volume 2), cesium-137 (volume 3), F. tularensis (volume 4), sulfur mustard (volume 5), americium-241 (volume 6), Y. pestis (volume 7), botulinum ... toxin (volume 8), plutonium-238/239 (volume 9) and vesicants (volume 10, an expansion on volume 5). This paper presents an inhalation exposure model for

Distribution and flux of 238Pu, 239,240Pu, 241Am, 137Cs and 210Pb to high arctic lakes in the Thule district (Greenland).

Science.gov (United States)

Eriksson, M; Holm, E; Roos, P; Dahlgaard, H

2004-01-01

Environmental samples (soil, sediment and lake water) in the Thule area (NW Greenland) have been studied to assess the contamination of radionuclides originating from a nuclear weapons accident (the Thule accident in 1968). Four lakes were chosen at different distances from the point of impact with the Thule air base community situated in between. The sedimentation rates in the lakes varied from 0.4 mm a(-1) (5 mg cm(-2) a(-1)) to 1.6 mm a(-1) (82 mg cm(-2) a(-1)). With these sedimentation rates, it is not possible to resolve the (239,240)Pu global fallout peak from a possible (239,240)Pu "accident" peak in the sediment depth profiles. However, the (239,240)Pu/(137)Cs and the (238)Pu/(239,240)Pu ratios agreed well with global fallout ratios, indicating that plutonium originating from the accident had not reached these lakes. This also indicates that the Thule air base community has probably only been exposed to radionuclides from the accident to a very limited extent. A limited study showed that (210)Pb could not be used as a normalizing nuclide to explain the transport of transuranic elements from the catchment area to the lake, i.e. (210)Pb has a different transport mechanism from that of the transuranic elements studied in this investigation.

Waste Isolation Pilot Plant TruDock crane system analysis

International Nuclear Information System (INIS)

Morris, B.C.; Carter, M.

1996-10-01

The WIPP TruDock crane system located in the Waste Handling Building was identified in the WIPP Safety Analysis Report (SAR), November 1995, as a potential accident concern due to failures which could result in a dropped load. The objective of this analysis is to evaluate the frequency of failure of the TruDock crane system resulting in a dropped load and subsequent loss of primary containment, i.e. drum failure. The frequency of dropped loads was estimated to be 9.81E-03/year or approximately one every 102 years (or, for the 25% contingency, 7.36E-03/year or approximately one every 136 years). The dominant accident contributor was the failure of the cable/hook assemblies, based on failure data obtained from NUREG-0612, as analyzed by PLG, Inc. The WIPP crane system undergoes a rigorous test and maintenance program, crane operation is discontinued following any abnormality, and the crane operator and load spotter are required to be trained in safe crane operation, therefore it is felt that the WIPP crane performance will exceed the data presented in NUREG-0612 and the estimated failure frequency is felt to be conservative

Radionuclide concentrations in soils and vegetation at Low-Level Radioactive Waste Disposal Area G during the 1998 growing season (with a cumulative summary of 3H and 239Pu over time)

International Nuclear Information System (INIS)

Fresquez, P.R.; Ebinger, M.H.; Wechsler, R.J.; Naranjo, L. Jr.

1999-01-01

Soils and unwashed overstory and understory vegetation were collected at eight locations within and around Area G, a disposal facility for low-level, radioactive solid waste at Los Alamos National Laboratory. The samples were analyzed for 3 H, 238 Pu, 239 Pu, 90 Sr, 241 Am, 137 Cs, tot U. Most of the radionuclide concentrations in soils and vegetation were within the upper 95% level of background concentrations except for 3 H and 239 Pu. Tritium concentrations in vegetation from most sites were greater than background concentrations of about 2 pCi mL -1 . The concentrations of 239 Pu in soils and understory vegetation were largest in samples collected several meters north of the transuranic waste pad area and were consistent with previous results. Based on 3 H and 239 Pu data through 1998, it was shown that concentrations were (1) significantly greater than background concentrations (p < 0.05) in soils and vegetation collected from most locations at Area G, and (2) there was no systematic increase or decrease in concentrations with time apparent in the data

Waste Generator Instructions: Key to Successful Implementation of the US DOE's 435.1 for Transuranic Waste Packaging Instructions (LA-UR-12-24155) - 13218

International Nuclear Information System (INIS)

French, David M.; Hayes, Timothy A.; Pope, Howard L.; Enriquez, Alejandro E.; Carson, Peter H.

2013-01-01

Generator Instructions (WGIs) have been used occasionally in the past at large sites for treatment and packaging of TRU waste. The WGIs have resulted in highly efficient waste treatment, packaging and certification for disposal of TRU waste at WIPP. For example, a single WGI at LANL, combined with an increase in gram loading, resulted in a mind boggling 6,400% increase in waste loading for 238 Pu heat source waste. In fact, the WGI combined with a new Contact Handled (CH) TRU Waste Content (TRUCON) Code provided a massive increase in shippable wattage per Transuranic Package Transporter-II (TRUPACT-II) over the previously used and more restrictive TRUCON Code that have been used previously for the heat source waste. In fact, the use of the WGI process at LANL's TA-55 facility reduced non-compliant drums for WIPP certification and disposal from a 13% failure rate down to a 0.5% failure rate and is expected to further reduce the failure rate to zero drums per year. The inherent value of the WGI is that it can be implemented in a site's current procedure issuance process and it provides documented proof of what actions were taken for each waste stream packaged. The WGI protocol provides a key floor-level operational component to achieve goal alignment between actual site operations, the WIPP TRU waste packaging instructions, and DOE O 435.1. (authors)

Defense Waste Management Plan for buried transuranic-contaminated waste, transuranic-contaminated soil, and difficult-to-certify transuranic waste

International Nuclear Information System (INIS)

1987-06-01

GAO recommended that DOE provide specific plans for permanent disposal of buried TRU-contaminated waste, TRU-contaminated soil, and difficult-to-certify TRU waste; cost estimates for permanent disposal of all TRU waste, including the options for the buried TRU-contaminated waste, TRU-contaminated soil, and difficult-to-certify TRU waste; and specific discussions of environmental and safety issues for the permanent disposal of TRU waste. Purpose of this document is to respond to the GAO recommendations by providing plans and cost estimates for the long-term isolation of the buried TRU-contaminated waste, TRU-contaminated soil, and difficult-to-certify TRU waste. This report also provides cost estimates for processing and certifying stored and newly generated TRU waste, decontaminating and decommissioning TRU waste processing facilities, and interim operations

Worldwide data on fluxes of 239,240Pu, 238Pu to the oceans

International Nuclear Information System (INIS)

Aarkrog, A.

1987-04-01

According to measurements (GEOSECS) the world's oceans contain approximately 16 PBq 239,240 Pu, of which one-fourth is in the Atlantic and three-fourths in the Pacific Ocean. The expected inventory (from nuclear weapons testing) in the world's oceans is 12 PBq 239,240 Pu including local fallout at the test sites. In the Irish Sea a local contamination of 0.3 PBq 239,240 Pu from the Sellafield reprocessing plant resides in the sediments. No other sources than fallout and reprocessing add significantly to the 239,240 Pu inventories in the oceans. The discrepancy between measurements and expectations are assumed to be due to an underestimate of the rainfall and dry fallout (seaspray) and thus of the Pu-deposition over the oceans, but may also to some degree be due to inadequate sampling

Criticality safety study of Pu contaminated carbon waste stored in 100 L steel drums

International Nuclear Information System (INIS)

Anno, J.; Simonneau, M.

1995-01-01

The notion of the minimum critical areal density (D minca ) used to ensure the Criticality-Safety of poor solid waste is recalled with its deficiencies. D minca is assumed constant, independent of the fissile material concentration. This assumption is only true for unreflected mediums. Corrective factors are established. Furthermore, the usual norm of the Pu-H 2 O, which is 0.20 g/cm 2 , (concrete reflected) is greater than that for other mediums, such as Pu contaminated graphite waste (Pu-C), which is 0.036 g/cm 2 . D minca calculated on infinite slabs is confirmed by calculations on infinite planar multilayers arrays of 100 l cubical waste drums. Moreover, d minca increases linearly with the steel thickness of the drums' walls and goes up to 0.17 g/cm 2 for 0.105 cm of steel. The safety analysis on a real storage case takes into account the limited amount of Pu (100 g) and C (100 kg), the minimum thickness of 0.07 cm of drums' steel, their geometrical arrangement, the heterogeneity and size of contamination and the occurrence of neutronic poison (N and Cl) in the waste. Because of these parameters, the Keff are very less than 0.95 and the taken norm of 0.1 g/cm 2 for the Pu-C waste is fulfilled. Finally, it is demonstrated that the mixing of Pu-C waste drums and Pu-H 2 O wastes drums is allowed. (authors). 14 refs., 5 figs., 6 tabs

Radiochemical methodologies applied to analytical characterization of low and intermediate level wastes from nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Monteiro, Roberto Pellacani G.; Júnior, Aluísio Souza R.; Kastner, Geraldo F.; Temba, Eliane S.C.; Oliveira, Thiago C. de; Amaral, Ângela M.; Franco, Milton B., E-mail: rpgm@cdtn.br, E-mail: reisas@cdtn.br, E-mail: gfk@cdtn.br, E-mail: esct@cdtn.br, E-mail: tco@cdtn.br, E-mail: ama@cdtn.br, E-mail: francom@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The aim of this work is to present radiochemical methodologies developed at CDTN/CNEN in order to answer a program for isotopic inventory of radioactive wastes from Brazilian Nuclear Power Plants. In this program some radionuclides, {sup 3}H, {sup 14}C, {sup 55}Fe, {sup 59}Ni, {sup 63}Ni, {sup 90}Sr, {sup 93}Zr, {sup 94}Nb, {sup 99}Tc, {sup 129}I, {sup 235}U, {sup 238}U, {sup 238}Pu, {sup 239}+{sup 240}Pu, {sup 241}Pu, {sup 242}Pu, {sup 241}Am, {sup 242}Cm e {sup 243}+{sup 244}Cm, were determined in Low Level Wastes (LLW) and Intermediate Level Wastes (ILW) and a protocol of analytical methodologies based on radiochemical separation steps and spectrometric and nuclear techniques was established. (author)

Global cooperation and conceptual design toward GNEP. Enhanced TRU burning fast reactor

International Nuclear Information System (INIS)

Ikeda, Kazumi; Maddox, James W.; Nakazato, Wataru; Kunishima, Shigeru

2008-01-01

In support of the GNEP (Global Nuclear Energy Partnership) program, AREVA and Mitsubishi Heavy Industries, Ltd. (MHI) seek to develop an ARR (Advanced Recycling Reactor) in concern with a CFTC (Consolidated Fuel Treatment Facility). This report presents the examination of more effective transuranics (TRU) burning core. Therefore some innovative technologies have been examined under the safety requirements; MA bearing fuel with 50% TRU fraction, moderator pin, fuel of high Am fraction, and Am blanket. The function of moderator is to enhance TRU burning capability, while increasing the Doppler effect and reducing the positive sodium void effect. The aim of 50% TRU fraction is to increase TRU burning capability by curbing plutonium production. Both high Am fraction of fuel and Am blanket can promote Am transmutation. According to the detailed calculation of high TRU (MA 15%, Pu 35% average) contained oxide fueled core with moderator pins of 12% arranged driver fuel assemblies, TRU conversion ratio decreases down to 0.33 and TRU burning capability is improved to 67kg/TWeh. Deploying Am blanket which is oxide fuel with Am 50% and U 50%, the total of Am transmutation capability becomes 69 kg/TWeh. (author)

W-026, transuranic waste restricted waste management (TRU RWM) glovebox operational test report

Energy Technology Data Exchange (ETDEWEB)

Leist, K.J.

1998-02-18

The TRU Waste/Restricted Waste Management (LLW/PWNP) Glovebox 401 is designed to accept and process waste from the Transuranic Process Glovebox 302. Waste is transferred to the glovebox via the Drath and Schraeder Bagless Transfer Port (DO-07401) on a transfer stand. The stand is removed with a hoist and the operator inspects the waste (with the aid of the Sampling and Treatment Director) to determine a course of action for each item. The waste is separated into compliant and non compliant. One Trip Port DO-07402A is designated as ``Compliant``and One Trip Port DO-07402B is designated as ``Non Compliant``. As the processing (inspection, bar coding, sampling and treatment) of the transferred items takes place, residue is placed in the appropriate One Trip port. The status of the waste items is tracked by the Data Management System (DMS) via the Plant Control System (PCS) barcode interface. As an item is moved for sampling or storage or it`s state altered by treatment, the Operator will track an items location using a portable barcode reader and entry any required data on the DMS console. The Operational Test Procedure (OTP) will perform evolutions (described here) using the Plant Operating Procedures (POP) in order to verify that they are sufficient and accurate for controlled glovebox operation.

W-026, transuranic waste restricted waste management (TRU RWM) glovebox operational test report

International Nuclear Information System (INIS)

Leist, K.J.

1998-01-01

The TRU Waste/Restricted Waste Management (LLW/PWNP) Glovebox 401 is designed to accept and process waste from the Transuranic Process Glovebox 302. Waste is transferred to the glovebox via the Drath and Schraeder Bagless Transfer Port (DO-07401) on a transfer stand. The stand is removed with a hoist and the operator inspects the waste (with the aid of the Sampling and Treatment Director) to determine a course of action for each item. The waste is separated into compliant and non compliant. One Trip Port DO-07402A is designated as ''Compliant''and One Trip Port DO-07402B is designated as ''Non Compliant''. As the processing (inspection, bar coding, sampling and treatment) of the transferred items takes place, residue is placed in the appropriate One Trip port. The status of the waste items is tracked by the Data Management System (DMS) via the Plant Control System (PCS) barcode interface. As an item is moved for sampling or storage or it's state altered by treatment, the Operator will track an items location using a portable barcode reader and entry any required data on the DMS console. The Operational Test Procedure (OTP) will perform evolutions (described here) using the Plant Operating Procedures (POP) in order to verify that they are sufficient and accurate for controlled glovebox operation

Waste Generator Instructions: Key to Successful Implementation of the US DOE's 435.1 for Transuranic Waste Packaging Instructions (LA-UR-12-24155) - 13218

Energy Technology Data Exchange (ETDEWEB)

French, David M. [LANL EES-12, Carlsbad, NM, Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545 (United States); Hayes, Timothy A. [LANL EES-12, Carlsbad, NM, Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545 (United States); Pope, Howard L. [Aspen Resources Ltd., Inc., P.O. Box 3038, Boulder, CO 80307 (United States); Enriquez, Alejandro E. [LANL NCO-4, Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545 (United States); Carson, Peter H. [LANL NPI-7, Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545 (United States)

2013-07-01

productive Waste Generator Instructions (WGIs) have been used occasionally in the past at large sites for treatment and packaging of TRU waste. The WGIs have resulted in highly efficient waste treatment, packaging and certification for disposal of TRU waste at WIPP. For example, a single WGI at LANL, combined with an increase in gram loading, resulted in a mind boggling 6,400% increase in waste loading for {sup 238}Pu heat source waste. In fact, the WGI combined with a new Contact Handled (CH) TRU Waste Content (TRUCON) Code provided a massive increase in shippable wattage per Transuranic Package Transporter-II (TRUPACT-II) over the previously used and more restrictive TRUCON Code that have been used previously for the heat source waste. In fact, the use of the WGI process at LANL's TA-55 facility reduced non-compliant drums for WIPP certification and disposal from a 13% failure rate down to a 0.5% failure rate and is expected to further reduce the failure rate to zero drums per year. The inherent value of the WGI is that it can be implemented in a site's current procedure issuance process and it provides documented proof of what actions were taken for each waste stream packaged. The WGI protocol provides a key floor-level operational component to achieve goal alignment between actual site operations, the WIPP TRU waste packaging instructions, and DOE O 435.1. (authors)

TRU waste transport economics: an overview

International Nuclear Information System (INIS)

Edling, D.A.; Hopkins, D.R.; Walls, H.C.

1978-01-01

There are currently three predominant methods used to transport transuranium contaminated waste. These are: (1) ATMX Railcars--500 and 600 series, (2) Super Tigers, and (3) Poly Panthers. Both the ATMX-500 and 600 series railcars are massive doubly walled steel railcars which provide the equivalent protection of a Type B package. In ATMX-600 the rapid loading and unloading of the 9 x 9 x 50 feet cargo space is achieved by prepackaging the TRU waste into standard 20-foot steel cargo containers. The ATMX-500 railcars are divided into three inside bays, having dimensions of 16 (l) x 9.25 (w) x 6.25 (h) feet. A typical load consists of 128 55-gallon drums (however, space can accommodate 192 drums), 12 fiberglass boxes (4 x 4 x 7), or a combination of palletized drums and boxes. A Super Tiger is an overpack authorized for Type A, Type B, and large quantities of radioactive materials having outside dimensions of 8 x 8 x 20 feet. Maximum payload is approximately 28,700 lb with a gross weight of 45,000 lb. The primary factors influencing transport costs are examined including freight rates of transport mode, effective cargo (weight and volume) management, effective utilization of available space (package design), transport mileage, and rental fees or initial capital outlay. Miscellaneous factors are also examined

Transuranic (Tru) waste volume reduction operations at a plutonium facility

Energy Technology Data Exchange (ETDEWEB)

Cournoyer, Michael E [Los Alamos National Laboratory; Nixon, Archie E [Los Alamos National Laboratory; Dodge, Robert L [Los Alamos National Laboratory; Fife, Keith W [Los Alamos National Laboratory; Sandoval, Arnold M [Los Alamos National Laboratory; Garcia, Vincent E [Los Alamos National Laboratory

2010-01-01

Programmatic operations at the Los Alamos National Laboratory Plutonium Facility (TA 55) involve working with various amounts of plutonium and other highly toxic, alpha-emitting materials. The spread of radiological contamination on surfaces, airborne contamination, and excursions of contaminants into the operator's breathing zone are prevented through use of a variety of gloveboxes (the glovebox, coupled with an adequate negative pressure gradient, provides primary confinement). Size-reduction operations on glovebox equipment are a common activity when a process has been discontinued and the room is being modified to support a new customer. The Actin ide Processing Group at TA-55 uses one-meter-long glass columns to process plutonium. Disposal of used columns is a challenge, since they must be size-reduced to get them out of the glovebox. The task is a high-risk operation because the glass shards that are generated can puncture the bag-out bags, leather protectors, glovebox gloves, and the worker's skin when completing the task. One of the Lessons Learned from these operations is that Laboratory management should critically evaluate each hazard and provide more effective measures to prevent personnel injury. A bag made of puncture-resistant material was one of these enhanced controls. We have investigated the effectiveness of these bags and have found that they safely and effectively permit glass objects to be reduced to small pieces with a plastic or rubber mallet; the waste can then be easily poured into a container for removal from the glove box as non-compactable transuranic (TRU) waste. This size-reduction operation reduces solid TRU waste generation by almost 2% times. Replacing one-time-use bag-out bags with multiple-use glass crushing bags also contributes to reducing generated waste. In addition, significant costs from contamination, cleanup, and preparation of incident documentation are avoided. This effort contributes to the Los Alamos