WorldWideScience

Sample records for pto rattle noise

  1. Experimental and numerical analysis of automotive gearbox rattle noise

    Science.gov (United States)

    Kadmiri, Younes; Rigaud, Emmanuel; Perret-Liaudet, Joël; Vary, Laurence

    2012-06-01

    The aim of this work is to characterize the rattle noise of automotive gearboxes, resulting from impacts between toothed wheels of unselected gear ratios. These stereo-mechanical impacts are modeled by a coefficient of restitution which describes damping during the squeezing of the lubricant film for approaching surfaces, and the elastic deformation of impacting bodies. The dynamic response of the loose gear first depends on the design parameters and the engine operating conditions. The unknown parameters are the drag torque and the coefficient of restitution. They are identified experimentally through implementation of two optical encoders in an actual automotive gearbox and the operation of a specific test bench which replicates the automotive power train. Models of the different drag torque sources are validated from analysis of the free damped response of the driveline. The coefficient of restitution and its probability density function are measured from experiments under stationary operating conditions. A nonlinear model is built. The dynamic response of the loose gear depends on the dimensionless backlash, the coefficient of restitution and a dimensionless parameter proposed to describe the rattle excitation level. Experiments under controlled excitation are performed to validate the assumptions, to confirm the ability of the parameter proposed to describe the rattle noise threshold, and to characterize the dynamic response. The nonlinear model predictions are fitted with the drag torque and coefficient of restitution previously identified. They are compared with measurements to demonstrate the ability of the model to predict gear rattle for any loose gear, any gearbox and any operating condition.

  2. Influence of Multiharmonics Excitation on Rattle Noise in Automotive Gearboxes

    Directory of Open Access Journals (Sweden)

    Y. Kadmiri

    2011-01-01

    Full Text Available We consider the automotive gearbox rattle noise resulting from vibro-impacts that can occur between the idle gears under excessive velocity fluctuations of the shaft-driving gears imposed by engine torque fluctuation. Even if the rattling phenomenon has no consequence on reliability, it may be particularly annoying for vehicle interior sound quality and acoustic comfort. The main parameters governing such kind of vibrations are the excitation source associated with engine torque fluctuation which can be modeled by an imposed displacement of the driveline, the inertia of the idle gear, the drag torque acting during the free flight motion, and the impact laws. In the case of rattle, it is reasonable to assume that duration of impacts between teeth is very short compared to the excitation period. Then, these impacts are modeled by a coefficient of restitution law. The excitation source is not composed only with fundamental component but also with other harmonic components. This study presents some effects of these additional components on the dynamic response of the idle gear.

  3. Signal Processing for MoC brake rattle noise of moving vehicles using prony analysis

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jae Cheol; Kwak, Yun Sang; Park, Jun Hong [Dept. of Mechanical Convergence Engineering, Hanyang University, Seoul (Korea, Republic of)

    2015-08-15

    To verify the possibility of generating rattling noise from a motor on caliper brake system, a test was conducted using a caliper excited with vibrations similar to that in a vehicle running on actual roads; this test was conducted using a quiet shaker installed in an anechoic room. After several hours of external excitation, the test assembly was loosened, and the frequency of rattling noise generation increased. A microphone was used to record the generated noise. The measured signals were analyzed by conventional spectrum analysis. Since the noise is generated as an impact response, the advantages of employing Prony analysis was discussed, and the results were compared to those obtained using conventional fast Fourier transforms. The accuracy of Prony analysis was through endurance tests on different brake systems.

  4. Measured Rattle Threshold of Residential House Windows

    Science.gov (United States)

    Sizov, Natalia; Schultz, Troy; Hobbs, Christopher; Klos, Jacob

    2008-01-01

    Window rattle is a common indoor noise effect in houses exposed to low frequency noise from such sources as railroads, blast noise and sonic boom. Human perception of rattle can be negative that is a motivating factor of the current research effort to study sonic boom induced window rattle. A rattle study has been conducted on residential houses containing windows of different construction at a variety of geographic locations within the United States. Windows in these houses were excited by a portable, high-powered loudspeaker and enclosure specifically designed to be mounted on the house exterior to cover an entire window. Window vibration was measured with accelerometers placed on different window components. Reference microphones were also placed inside the house and inside of the loudspeaker box. Swept sine excitation was used to identify the vibration threshold at which the response of the structure becomes non-linear and begins to rattle. Initial results from this study are presented and discussed. Future efforts will continue to explore the rattle occurrence in windows of residential houses exposed to sonic booms.

  5. Rattles of Clay.

    Science.gov (United States)

    Banning, Donna

    1983-01-01

    Using the rattles of Native American cultures as inspiration, students used pinching, coiling, and slab and molding techniques to form the bodies of rattles and clay pellets for sound. Surface decoration included glazed and unglazed areas as well as added handles, feathers, and leather. (IS)

  6. PTO: The New Keyword

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ On November 5, the State Council made public the new paid-time-off (PTO) regulations in order to get some feedback. As a result, "PTO"has become the most searched keyword in China;shortly after the announcement more than 140,000 people had participated in a survey on Sina.com, with nearly 60% showing their support of the new policies.

  7. Lightly loaded lubricated impacts: Idle gear rattle

    Science.gov (United States)

    Tangasawi, O.; Theodossiades, S.; Rahnejat, H.

    2007-12-01

    Idle gear rattle is associated with the characteristic noise that unselected impacting gears radiate to the environment. It is induced by engine order vibration in the presence of backlash in the unengaged gear pairs, resulting in oscillatory response within their backlash range. A tribo-dynamic model of a front wheel drive manual transmission has been developed to study idle rattle, considering the hydrodynamic contact film reaction and flank friction. The model includes the torsional motions of the idle gears and the lateral motions of the supporting output shafts. The hydrodynamic lubricant film formed between the gear teeth under light impact loads behaves as a nonlinear spring-damper mechanism, whilst the inclusion of the shafts' bearing compliances introduces additional nonlinear terms, which are modelled as piecewise linear functions. The aim of the paper is to extend the existing methodology reported by the authors on idle rattle investigations of geared lubricated systems, based on torsional vibrations only, by considering the system response, which is eventually transferred to the gearbox case through the bearings. These are preliminary results found, which conform closely to experimental measurements taken from a vehicle equipped with a manual transmission of the same type.

  8. Crystal structure of the complex between Pseudomonas effector AvrPtoB and the tomato Pto kinase reveals both a shared and a unique interface compared with AvrPto-Pto.

    Science.gov (United States)

    Dong, Jing; Xiao, Fangming; Fan, Fenxia; Gu, Lichuan; Cang, Huaixing; Martin, Gregory B; Chai, Jijie

    2009-06-01

    Resistance to bacterial speck disease in tomato (Solanum lycopersicum) is activated upon recognition by the host Pto kinase of either one of two sequence-unrelated effector proteins, AvrPto or AvrPtoB, from Pseudomonas syringae pv tomato (Pst). Pto induces Pst immunity by acting in concert with the Prf protein. The recently reported structure of the AvrPto-Pto complex revealed that interaction of AvrPto with Pto appears to relieve an inhibitory effect of Pto, allowing Pto to activate Prf. Here, we present the crystal structure of the Pto binding domain of AvrPtoB (residues 121 to 205) at a resolution of 1.9A and of the AvrPtoB(121-205)-Pto complex at a resolution of 3.3 A. AvrPtoB(121-205) exhibits a tertiary fold that is completely different from that of AvrPto, and its conformation remains largely unchanged upon binding to Pto. In common with AvrPto-Pto, the AvrPtoB-Pto complex relies on two interfaces. One of these interfaces is similar in both complexes, although the primary amino acid sequences from the two effector proteins are very different. Amino acid substitutions in Pto at the other interface disrupt the interaction of AvrPtoB-Pto but not that of AvrPto-Pto. Interestingly, substitutions in Pto affecting this unique interface also cause Pto to induce Prf-dependent host cell death independently of either effector protein.

  9. Influence of tooth profile error in gear rattle (2nd report; In the case of multi-step gear system)

    OpenAIRE

    濱野, 崇; 吉武, 裕; 田村, 尋徳; 濵田, 知宏; 原田, 晃; 小林, 敦

    2009-01-01

    Gear rattle of multi-step helical gear system is treated. Mesh stiffness variations and tooth profile errors are considered within the system. The effects of mesh stiffness variations, the ratio of static torque to dynamic one and tooth profile errors on the rattle are studied by a highly accurate numerical analysis called the shooting method. As a result, the followings were made clear. (1) Because of the tooth profile errors, the amplitude of resonances like gear noise becomes large and the...

  10. [Efficacy of glycopyrronium bromide and scopolamine hydrobromide in patients with death rattle: a randomized controlled study].

    Science.gov (United States)

    Likar, Rudolf; Rupacher, Ernst; Kager, Hans; Molnar, Mario; Pipam, Wofgang; Sittl, Reinhard

    2008-01-01

    Death rattle is an extremely distressing symptom for the dying patient and for his environment. The aim of this study was to assess the efficacy of glycopyrronium bromide as compared with scopolamine hydrobromide in alleviating death rattle in terminal cancer patients with cognitive impairment. In a randomized, controlled study design patients were allocated in two groups. Group A received scopolamine hydrobromide in a dose of 0.5 mg intravenously every 6 hours for a period of 12 hours, group B received glycopyrronium bromide 0.4 mg every 6 hours for a period of 12 hours. In addition, standardized sedatives were administered as required and the analgesic therapy continued either orally or, if necessary, subcutaneously or intravenously in equipotent doses. Every 2 hours death rattle was assessed and rated on a scale of 1 to 5 (1 = audible breathing noises, 5 = very severe rattling noises). In addition, restlessness and expressions of pain were assessed and rated on a scale of 1 to 3 (1 = mild, 2 = moderate, 3 = severe). 13 patients were included in the study, 7 patients were allocated to group A and 6 patients to group B. There were no significant differences in demographic data, age, weight and diagnosis distribution between the two groups. Group B demonstrated a significant reduction of death rattle in the first 12 hours (p = 0.029) in comparison to group A. There were no significant differences concerning the side effects (restlessness, expressions of pain) in both groups. Glycopyrronium bromide given in a dose of 0,4 mg every six hours demonstrated a significant reduction of death rattle compared to scopolamine hydrobromide. Concerning side effects (restlessness, expressions of pain) there was no difference between both substances.

  11. Natural variation in the Pto pathogen resistance gene within species of wild tomato (Lycopersicon). I. Functional analysis of Pto alleles.

    Science.gov (United States)

    Rose, Laura E; Langley, Charles H; Bernal, Adriana J; Michelmore, Richard W

    2005-09-01

    Disease resistance to the bacterial pathogen Pseudomonas syringae pv. tomato (Pst) in the cultivated tomato, Lycopersicon esculentum, and the closely related L. pimpinellifolium is triggered by the physical interaction between plant disease resistance protein, Pto, and the pathogen avirulence protein, AvrPto. To investigate the extent to which variation in the Pto gene is responsible for naturally occurring variation in resistance to Pst, we determined the resistance phenotype of 51 accessions from seven species of Lycopersicon to isogenic strains of Pst differing in the presence of avrPto. One-third of the plants displayed resistance specifically when the pathogen expressed AvrPto, consistent with a gene-for-gene interaction. To test whether this resistance in these species was conferred specifically by the Pto gene, alleles of Pto were amplified and sequenced from 49 individuals and a subset (16) of these alleles was tested in planta using Agrobacterium-mediated transient assays. Eleven alleles conferred a hypersensitive resistance response (HR) in the presence of AvrPto, while 5 did not. Ten amino acid substitutions associated with the absence of AvrPto recognition and HR were identified, none of which had been identified in previous structure-function studies. Additionally, 3 alleles encoding putative pseudogenes of Pto were isolated from two species of Lycopersicon. Therefore, a large proportion, but not all, of the natural variation in the reaction to strains of Pst expressing AvrPto can be attributed to sequence variation in the Pto gene.

  12. Educational Data Mining Model Using Rattle

    Directory of Open Access Journals (Sweden)

    Sadiq Hussain

    2014-07-01

    Full Text Available Data Mining is the extraction of knowledge from the large databases. Data Mining had affected all the fields from combating terror attacks to the human genome databases. For different data analysis, R programming has a key role to play. Rattle, an effective GUI for R Programming is used extensively for generating reports based on several current trends models like random forest, support vector machine etc. It is otherwise hard to compare which model to choose for the data that needs to be mined. This paper proposes a method using Rattle for selection of Educational Data Mining Model.

  13. Regulation of tomato Prf by Pto-like protein kinases.

    Science.gov (United States)

    Mucyn, Tatiana S; Wu, Ai-Jiuan; Balmuth, Alexi L; Arasteh, Julia Maryam; Rathjen, John P

    2009-04-01

    Tomato Prf encodes a nucleotide-binding domain shared by Apaf-1, certain R proteins, and CED-4 fused to C-terminal leucine-rich repeats (NBARC-LRR) protein that is required for bacterial immunity to Pseudomonas syringae and sensitivity to the organophosphate fenthion. The signaling pathways involve two highly related protein kinases. Pto kinase mediates direct recognition of the bacterial effector proteins AvrPto or AvrPtoB. Fen kinase is required for fenthion sensitivity and recognition of bacterial effectors related to AvrPtoB. The role of Pto and its association with Prf has been characterized but Fen is poorly described. We show that, similar to Pto, Fen requires N-myristoylation and kinase activity for signaling and interacts with the N-terminal domain of Prf. Thus, the mechanisms of activation of Prf by the respective protein kinases are similar. Prf-Fen interaction is underlined by coregulatory mechanisms in which Prf negatively regulates Fen, most likely by controlling kinase activity. We further characterized negative regulation of Prf by Pto, and show that regulation is mediated by the previously described negative regulatory patch. Remarkably, the effectors released negative regulation of Prf in a manner dependent on Pto kinase activity. The data suggest a model in which Prf associates generally with Pto-like kinases in tightly regulated complexes, which are activated by effector-mediated disruption of negative regulation. Release of negative regulation may be a general feature of activation of NBARC-LRR proteins by cognate effectors.

  14. Pto- and Prf-mediated recognition of AvrPto and AvrPtoB restricts the ability of diverse pseudomonas syringae pathovars to infect tomato.

    Science.gov (United States)

    Lin, Nai-Chun; Martin, Gregory B

    2007-07-01

    The molecular basis underlying the ability of pathogens to infect certain plant species and not others is largely unknown. Pseudomonas syringae is a useful model species for investigating this phenomenon because it comprises more than 50 pathovars which have narrow host range specificities. Tomato (Solanum lycopersicum) is a host for P. syringae pv. tomato, the causative agent of bacterial speck disease, but is considered a nonhost for other P. syringae pathovars. Host resistance in tomato to bacterial speck disease is conferred by the Pto protein kinase which acts in concert with the Prf nucleotide-binding lucine-rich repeat protein to recognize P. syringae pv. tomato strains expressing the type III effectors AvrPto or AvrPtoB (HopAB2). The Pto and Prf genes were isolated from the wild tomato species S. pimpinellifolium and functional alleles of both of these genes now are known to exist in many species of tomato and in other Solanaceous species. Here, we extend earlier reports that avrPto and avrPtoB genes are widely distributed among pathovars of P. syringae which are considered nonhost pathogens of tomato. This observation prompted us to examine the possibility that recognition of these type III effectors by Pto or Prf might contribute to the inability of many P. syringae pathovars to infect tomato species. We show that 10 strains from presumed nonhost P. syringae pathovars are able to grow and cause pathovar-unique disease symptoms in tomato leaves lacking Pto or Prf, although they did not reach the population levels or cause symptoms as severe as a control P. syringae pv. tomato strain. Seven of these strains were found to express avrPto or avrPtoB. The AvrPto- and AvrPtoB-expressing strains elicited disease resistance on tomato leaves expressing Pto and Prf. Thus, a gene-for-gene recognition event may contribute to host range restriction of many P. syringae pathovars on tomato species. Furthermore, we conclude that the diverse disease symptoms caused by

  15. Natural variation in the Pto disease resistance gene within species of wild tomato (Lycopersicon). II. Population genetics of Pto.

    Science.gov (United States)

    Rose, Laura E; Michelmore, Richard W; Langley, Charles H

    2007-03-01

    Disease resistance to the bacterial pathogen Pseudomonas syringae pv. tomato (Pst) in the host species Lycopersicon esculentum, the cultivated tomato, and the closely related L. pimpinellifolium is triggered by the physical interaction between the protein products of the host resistance (R) gene Pto and the pathogen avirulence genes AvrPto and AvrPtoB. Sequence variation at the Pto locus was surveyed in natural populations of seven species of Lycopersicon to test hypotheses of host-parasite coevolution and functional adaptation of the Pto gene. Pto shows significantly higher nonsynonymous polymorphism than 14 other non-R-gene loci in the same samples of Lycopersicon species, while showing no difference in synonymous polymorphism, suggesting that the maintenance of amino acid polymorphism at this locus is mediated by pathogen selection. Also, a larger proportion of ancestral variation is maintained at Pto as compared to these non-R-gene loci. The frequency spectrum of amino acid polymorphisms known to negatively affect Pto function is skewed toward low frequency compared to amino acid polymorphisms that do not affect function or silent polymorphisms. Therefore, the evolution of Pto appears to be influenced by a mixture of both purifying and balancing selection.

  16. Periodically fighting shake, rattle and roll

    CERN Document Server

    Brun, M; Jones, I S

    2011-01-01

    How easy is it to suppress shake, rattle and roll in a long bridge or a skyscraper? Most practical structures are designed so that long wave resonance vibrations can be avoided. However, there are recent examples, such as the Millennium Bridge in London or the Volga Bridge in Volgograd, which show that unexpected external forces may result in large scale unwanted shake and rattle. Full scale alteration of a bridge (or a skyscraper) would not be considered as an acceptable option, unless the structure has collapsed. Can we fix this by examining a representative part of the structure only and making small lightweight changes? We will do it here and illustrate an idea linking the engineering analysis to elastic waveguides.

  17. High-Speed RaPToRS

    Science.gov (United States)

    Henchen, Robert; Esham, Benjamin; Becker, William; Pogozelski, Edward; Padalino, Stephen; Sangster, Thomas; Glebov, Vladimir

    2008-11-01

    The High-Speed Rapid Pneumatic Transport of Radioactive Samples (HS-RaPToRS) system, designed to quickly and safely move radioactive materials, was assembled and tested at the Mercury facility of the Naval Research Laboratory (NRL) in Washington D.C. A sample, which is placed inside a four-inch-diameter carrier, is activated before being transported through a PVC tube via airflow. The carrier travels from the reaction chamber to the end station where it pneumatically brakes prior to the gate. A magnetic latch releases the gate when the carrier arrives and comes to rest. The airflow, optical carrier-monitoring devices, and end gate are controlled manually or automatically with LabView software. The installation and testing of the RaPToRS system at NRL was successfully completed with transport times of less than 3 seconds. The speed of the carrier averaged 16 m/s. Prospective facilities for similar systems include the Laboratory for Laser Energetics and the National Ignition Facility.

  18. Bypassing kinase activity of the tomato Pto resistance protein with small molecule ligands.

    Science.gov (United States)

    Salomon, Dor; Bonshtien, Arale; Mayrose, Maya; Zhang, Chao; Shokat, Kevan M; Sessa, Guido

    2009-05-29

    The tomato (Solanum lycopersicum) protein kinase Pto confers resistance to Pseudomonas syringae pv. tomato bacteria expressing the AvrPto and AvrPtoB effector proteins. Pto specifically recognizes both effectors by direct physical interactions triggering activation of immune responses. Here, we used a chemical-genetic approach to sensitize Pto to analogs of PP1, an ATP-competitive small molecule inhibitor. By using PP1 analogs in combination with the sensitized Pto (Pto(as)), we examined the role of Pto kinase activity in effector recognition and signal transduction. Strikingly, while PP1 analogs efficiently inhibited kinase activity of Pto(as) in vitro, they enhanced interactions of Pto(as) with AvrPto and AvrPtoB in a yeast two-hybrid system. In addition, in the presence of PP1 analogs, Pto(as) bypassed mutations either at an autophosphorylation site critical for the Pto-AvrPto interaction or at catalytically essential residues and interacted with both effectors. Moreover, in the presence of the PP1 analog 3MB-PP1, a kinase-deficient form of Pto(as) triggered an AvrPto-dependent hypersensitive response in planta. These findings suggest that, rather than phosphorylation per se, a conformational change likely triggered by autophosphorylation in Pto and mimicked by ligand binding in Pto(as) is a prerequisite for recognition of bacterial effectors. Following recognition, kinase activity appears to be dispensable for Pto signaling in planta. The chemical-genetic strategy applied here to develop specific small molecule inhibitors of Pto represents an invaluable tool for the study of biological functions of other plant protein kinases in vivo.

  19. Characterization of PTO and Idle Behavior for Utility Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Duran, Adam W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Konan, Arnaud M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Miller, Eric S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kelly, Kenneth J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Prohaska, Robert S [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-09-28

    This report presents the results of analyses performed on utility vehicle data composed primarily of aerial lift bucket trucks sampled from the National Renewable Energy Laboratory's Fleet DNA database to characterize power takeoff (PTO) and idle operating behavior for utility trucks. Two major data sources were examined in this study: a 75-vehicle sample of Odyne electric PTO (ePTO)-equipped vehicles drawn from multiple fleets spread across the United States and 10 conventional PTO-equipped Pacific Gas and Electric fleet vehicles operating in California. Novel data mining approaches were developed to identify PTO and idle operating states for each of the datasets using telematics and controller area network/onboard diagnostics data channels. These methods were applied to the individual datasets and aggregated to develop utilization curves and distributions describing PTO and idle behavior in both absolute and relative operating terms. This report also includes background information on the source vehicles, development of the analysis methodology, and conclusions regarding the study's findings.

  20. Genetic and molecular requirements for function of the Pto/Prf effector recognition complex in tomato and Nicotiana benthamiana.

    Science.gov (United States)

    Balmuth, Alexi; Rathjen, John P

    2007-09-01

    The Pto gene of tomato (Solanum lycopersicum) confers specific recognition of the unrelated bacterial effector proteins AvrPto and AvrPtoB. Pto resides in a constitutive molecular complex with the nucleotide binding site-leucine rich repeats protein Prf. Prf is absolutely required for specific recognition of both effectors. Here, using stable transgenic lines, we show that expression of Pto from its genomic promoter in susceptible tomatoes was sufficient to complement recognition of Pseudomonas syringae pv. tomato (Pst) bacteria expressing either avrPto or avrPtoB. Pto kinase activity was absolutely required for specific immunity. Expression of the Pto N-myristoylation mutant, pto(G2A), conferred recognition of Pst (avrPtoB), but not Pst (avrPto), although bacterial growth in these lines was intermediate between resistant and susceptible lines. Overexpression of pto(G2A) complemented recognition of avrPto. Transgenic tomato plants overexpressing wild-type Pto exhibited constitutive growth phenotypes, but these were absent in lines overexpressing pto(G2A). Therefore, Pto myristoylation is a quantitative factor for effector recognition in tomato, but is absolutely required for overexpression phenotypes. Native expression of Pto in the heterologous species Nicotiana benthamiana did not confer resistance to P. syringae pv. tabaci (Pta) expressing avrPto or avrPtoB, but recognition of both effectors was complemented by Prf co-expression. Thus, specific resistance conferred solely by Pto in N. benthamiana is an artefact of overexpression. Finally, pto(G2A) did not confer recognition of either avrPto or avrPtoB in N. benthamiana, regardless of the presence of Prf. Thus, co-expression of Prf in N. benthamiana complements many but not all aspects of normal Pto function.

  1. INVESTIGATION OF RATTLING THRESHOLD IN GEAR SYSTEM

    Institute of Scientific and Technical Information of China (English)

    Dong Haijun; Shen Yunwen; Liu Mengjun; Wang Sanmin

    2005-01-01

    A lumped mass gear-rattling model with backlash is established by considering the time varying mesh stiffness, composite transmission error and the torque fluctuation. Based on the principle that no separation will occur if the response amplitude is not larger than the static response,the threshold is obtained by theoretical derivation. The validity of the theoretical derivation is verified by the numerical method. The results show that the time-varying mesh stiffness has little effect on the threshold. When the exciting frequency is less than the system natural frequency, the theoretical agrees well with the numerical one. The higher the exciting frequency or the smaller the average input torque is, the easier the separation will occur. When the exciting frequency is larger than the natural frequency by a certain value, the theoretical threshold does not agree with the numerical results. The numerical results show that the motion state will change from the meshing state to the separating state directly. The phenomenon that the gear pair sometimes separates and sometimes meshes occurs only when the exciting frequency is smaller.

  2. The tomato Prf complex is a molecular trap for bacterial effectors based on Pto transphosphorylation.

    Science.gov (United States)

    Ntoukakis, Vardis; Balmuth, Alexi L; Mucyn, Tatiana S; Gutierrez, Jose R; Jones, Alexandra M E; Rathjen, John P

    2013-01-01

    The major virulence strategy of phytopathogenic bacteria is to secrete effector proteins into the host cell to target the immune machinery. AvrPto and AvrPtoB are two such effectors from Pseudomonas syringae, which disable an overlapping range of kinases in Arabidopsis and Tomato. Both effectors target surface-localized receptor-kinases to avoid bacterial recognition. In turn, tomato has evolved an intracellular effector-recognition complex composed of the NB-LRR protein Prf and the Pto kinase. Structural analyses have shown that the most important interaction surface for AvrPto and AvrPtoB is the Pto P+1 loop. AvrPto is an inhibitor of Pto kinase activity, but paradoxically, this kinase activity is a prerequisite for defense activation by AvrPto. Here using biochemical approaches we show that disruption of Pto P+1 loop stimulates phosphorylation in trans, which is possible because the Pto/Prf complex is oligomeric. Both P+1 loop disruption and transphosphorylation are necessary for signalling. Thus, effector perturbation of one kinase molecule in the complex activates another. Hence, the Pto/Prf complex is a sophisticated molecular trap for effectors that target protein kinases, an essential aspect of the pathogen's virulence strategy. The data presented here give a clear view of why bacterial virulence and host recognition mechanisms are so often related and how the slowly evolving host is able to keep pace with the faster-evolving pathogen.

  3. The tomato Prf complex is a molecular trap for bacterial effectors based on Pto transphosphorylation.

    Directory of Open Access Journals (Sweden)

    Vardis Ntoukakis

    2013-01-01

    Full Text Available The major virulence strategy of phytopathogenic bacteria is to secrete effector proteins into the host cell to target the immune machinery. AvrPto and AvrPtoB are two such effectors from Pseudomonas syringae, which disable an overlapping range of kinases in Arabidopsis and Tomato. Both effectors target surface-localized receptor-kinases to avoid bacterial recognition. In turn, tomato has evolved an intracellular effector-recognition complex composed of the NB-LRR protein Prf and the Pto kinase. Structural analyses have shown that the most important interaction surface for AvrPto and AvrPtoB is the Pto P+1 loop. AvrPto is an inhibitor of Pto kinase activity, but paradoxically, this kinase activity is a prerequisite for defense activation by AvrPto. Here using biochemical approaches we show that disruption of Pto P+1 loop stimulates phosphorylation in trans, which is possible because the Pto/Prf complex is oligomeric. Both P+1 loop disruption and transphosphorylation are necessary for signalling. Thus, effector perturbation of one kinase molecule in the complex activates another. Hence, the Pto/Prf complex is a sophisticated molecular trap for effectors that target protein kinases, an essential aspect of the pathogen's virulence strategy. The data presented here give a clear view of why bacterial virulence and host recognition mechanisms are so often related and how the slowly evolving host is able to keep pace with the faster-evolving pathogen.

  4. Seroprevalence of porcine torovirus (PToV in Spanish farms

    Directory of Open Access Journals (Sweden)

    Alonso-Padilla Julio

    2012-12-01

    Full Text Available Abstract Background Torovirus infections have been associated with gastroenteritis and diarrhea in horses, cows, pigs and humans, especially in young animals and in children. Although asymptomatic in a large percentage of cases, however toroviruses may pose a potential threat to worsen disease outcome in concurrent infections with other enteric pathogens. Previous studies based on the analysis of limited numbers of samples indicated high seroprevalences against porcine torovirus (PToV in various European countries. The aim of this work was to perform a seroepidemiological survey of PToV in Spanish farms in order to define the seroprevalence against this virus. Results Serum samples (n = 2664 from pigs of different ages were collected from 100 Spanish farms coming from 10 regions that concentrate 96.1% of the 3392 farms with 80 or more sows censused in Spain. Samples were screened by means of an indirect enzyme-linked immune-sorbent assay (ELISA based on a recombinant PToV nucleocapsid protein as antigen. The analysis of the whole serum collection yielded a total of 95.7% (2550/2664 seropositive samples. The highest prevalence (99.6%, 1382/1388 and ELISA values (average O.D. ± standard deviation were observed in the sows (1.03±0.36 and the lowest prevalence (59.4%, 98/165 and anti-PToV IgG levels (0.45±0.16 were found amongst 3-week-old piglets. Both ELISA reactivity values and seroprevalence percentages rose quickly with piglet’s age from 3 to 11 weeks of age; the seroprevalence was 99.3% (2254/2270 when only the samples from sows and pigs over 11-weeks of age were considered. Antibodies against PToV were detected in all analyzed farms. Conclusions This report describes the results of the largest torovirus seroepidemiological survey in farmed swine performed so far. Overall, the seroprevalence against PToV in animals older than 11 weeks of age was >99%, indicating that this virus is endemic in pig herds from Spain.

  5. Direct Determination of the Ionization Energies of PtC, PtO, and PtO2 with VUVRadiation

    Energy Technology Data Exchange (ETDEWEB)

    Citir, Murat; Metz, Ricardo B.; Belau, Leonid; Ahmed, Musahid

    2008-07-21

    Photoionization efficiency curves were measured for gas-phase PtC, PtO, and PtO2 using tunable vacuum ultraviolet (VUV) radiation at the Advanced Light Source. The molecules were prepared by laser ablation of a platinum tube, followed by reaction with CH4 or N2O and supersonic expansion. These measurements providethe first directly measured ionization energy for PtC, IE(PtC) = 9.45 +- 0.05 eV. The direct measurement also gives greatly improved ionization energies for the platinum oxides, IE(PtO) = 10.0 +- 0.1 eV and IE(PtO2) = 11.35 +- 0.05 eV. The ionization energy connects the dissociation energies of the neutral and cation, leading to greatly improved 0 K bond dissociation energies for the neutrals: D0(Pt-C) = 5.95 +- 0.07 eV, D0(Pt-O)= 4.30 +- 0.12 eV, and D0(OPt-O) = 4.41 +- 0.13 eV, as well as enthalpies of formation for the gas-phase molecules Delta H0 f,0(PtC(g)) = 701 +- 7 kJ/mol, Delta H0f,0(PtO(g)) = 396 +- 12 kJ/mol, and Delta H0f,0(PtO2(g)) = 218 +- 11 kJ/mol. Much of the error in previous Knudsen cell measurements of platinum oxide bond dissociation energies is due to the use of thermodynamic second law extrapolations. Third law values calculated using statistical mechanical thermodynamic functions are in much better agreement with values obtained from ionization energies and ion energetics. These experiments demonstrate that laser ablation production with direct VUV ionization measurements is a versatile tool to measure ionization energies and bond dissociation energies for catalytically interesting species such as metal oxides and carbides.

  6. Experimental study on the updated PTO system of the WEPTOS Wave Energy Converter

    DEFF Research Database (Denmark)

    Pecher, Arthur; Kofoed, Jens Peter

    This report presents the results of an experimental study that was performed on a test model, which was mainly composed out of 3 Weptos rotors and a new power take off (PTO) system. During these tests, various variables related to the design of the PTO system, rotor and overall design of the device...

  7. Investigation and Optimisation of a Discrete Fluid Power PTO-system for Wave Energy Converters

    DEFF Research Database (Denmark)

    Hansen, Anders Hedegaard

    recently focused research on improving the power take off (PTO) system converting the mechanical motion of the floats into electricity. This has brought attention to discrete fluid power (DFP) technology, especially secondary controlled common pressure rail systems. A novel discrete PTO-system has been...... proposed and found feasible for the Wavestar WEC. However, with a technology shift from a continuous to a discrete fluid power PTO-system, new challenges emerge. The current project investigates and optimises the novel discrete fluid power PTO-system proposed for the Wavestar WEC. Initiating from...... an investigation of energy extraction by WECs utilising a discrete PTO force, an investigation of the system configuration is conducted. Hence, the configuration of the multi-chamber cylinder and the common pressure rails are investigated for the discrete fluid power force system. A method for choosing the system...

  8. Noise

    Science.gov (United States)

    Noise is all around you, from televisions and radios to lawn mowers and washing machines. Normally, you ... sensitive structures of the inner ear and cause noise-induced hearing loss. More than 30 million Americans ...

  9. The tomato NBARC-LRR protein Prf interacts with Pto kinase in vivo to regulate specific plant immunity.

    Science.gov (United States)

    Mucyn, Tatiana S; Clemente, Alfonso; Andriotis, Vasilios M E; Balmuth, Alexi L; Oldroyd, Giles E D; Staskawicz, Brian J; Rathjen, John P

    2006-10-01

    Immunity in tomato (Solanum lycopersicum) to Pseudomonas syringae bacteria expressing the effector proteins AvrPto and AvrPtoB requires both Pto kinase and the NBARC-LRR (for nucleotide binding domain shared by Apaf-1, certain R gene products, and CED-4 fused to C-terminal leucine-rich repeats) protein Prf. Pto plays a direct role in effector recognition within the host cytoplasm, but the role of Prf is unknown. We show that Pto and Prf are coincident in the signal transduction pathway that controls ligand-independent signaling. Pto and Prf associate in a coregulatory interaction that requires Pto kinase activity and N-myristoylation for signaling. Pto interacts with a unique Prf N-terminal domain outside of the NBARC-LRR domain and resides in a high molecular weight recognition complex dependent on the presence of Prf. In this complex, both Pto and Prf contribute to specific recognition of AvrPtoB. The data suggest that the role of Pto is confined to the regulation of Prf and that the bacterial effectors have evolved to target this coregulatory molecular switch.

  10. Prf immune complexes of tomato are oligomeric and contain multiple Pto-like kinases that diversify effector recognition.

    Science.gov (United States)

    Gutierrez, Jose R; Balmuth, Alexi L; Ntoukakis, Vardis; Mucyn, Tatiana S; Gimenez-Ibanez, Selena; Jones, Alexandra M E; Rathjen, John P

    2010-02-01

    Cytoplasmic recognition of pathogen virulence effectors by plant NB-LRR proteins leads to strong induction of defence responses termed effector triggered immunity (ETI). In tomato, a protein complex containing the NB-LRR protein Prf and the protein kinase Pto confers recognition of the Pseudomonas syringae effectors AvrPto and AvrPtoB. Although structurally unrelated, AvrPto and AvrPtoB interact with similar residues in the Pto catalytic cleft to activate ETI via an unknown mechanism. Here we show that the Prf complex is oligomeric, containing at least two molecules of Prf. Within the complex, Prf can associate with Pto or one of several Pto family members including Fen, Pth2, Pth3, or Pth5. The dimerization surface for Prf is the novel N-terminal domain, which also coordinates an intramolecular interaction with the remainder of the molecule, and binds Pto kinase or a family member. Thus, association of two Prf N-terminal domains brings the associated kinases into close promixity. Tomato lines containing Prf complexed with Pth proteins but not Pto possessed greater immunity against P. syringae than tomatoes lacking Prf. This demonstrates that incorporation of non-Pto kinases into the Prf complex extends the number of effector proteins that can be recognized.

  11. Optimal Discrete PTO Force Point Absorber Wave Energy Converters in Regular Waves

    DEFF Research Database (Denmark)

    Hansen, Anders Hedegaard; Pedersen, Henrik C.

    2013-01-01

    the conventional fluid power systems suffer of poor efficiency. Therefore discrete fluid power force systems have been proposed. Limited research has, however, been conducted with focus on choosing the discrete force levels and force profiles for a discrete PTO system for WECs. This paper is to support the design...... of discrete force systems for PTO, by focusing on how to choose the optimal PTO force levels and force profile when seeking to increase energy harvesting. The work concerns point absorber WECs and utilises a simple float model based on linear wave theory. Utilising the principle of superposition...

  12. Genome-Wide Analysis and Evolution of the Pto-Like Protein Kinase (PLPK) Gene Family in Pepper

    Science.gov (United States)

    Venkatesh, Jelli; Jahn, Molly; Kang, Byoung-Cheorl

    2016-01-01

    The tomato Pto gene, which encodes a serine/threonine kinase (STK) domain-containing protein, confers resistance to bacterial speck disease caused by Pseudomonas syringae pv. tomato (Pst). In this study, in vivo recognition assays using PVX constructs showed that AvrPto was specifically recognized in the pepper genotypes. This AvrPto recognition caused a nonhost hypersensitive response (HR) and localization of the PVX::AvrPto fusion protein to inoculated pepper leaf tissues, which indicates the presence of a similar Pto recognition mechanism in pepper as in tomato. However, genome-wide analysis in pepper revealed no Pto clade corresponding to that in tomato, suggesting an alternative system for Pto recognition in pepper. Nevertheless, 25 Pto-like protein kinases (PLPKs) with a highly conserved STK domain have been identified in the pepper genome. For the majority of the amino acid sites in the STK domain of Ptos and PLPKs, nonsynonymous (dN) to synonymous (dS) nucleotide substitution ratios (ω) were less than one, suggesting that purifying selection played a predominant role in the evolutionary process. However, some amino acid sites were found to be subjected to episodic positive selection in the course of evolution of Pto homologs, and, thus, different evolutionary processes might have shaped the Pto gene family in plants. Based on RNA-seq data, PLPK genes and other Pto pathway genes, such as Prf, Pti1, Pti5, and Pti6 were expressed in all tested pepper genotypes. Therefore, the nonhost HR against Pst in pepper may be due to the recognition of the AvrPto effector by a PLPK homolog, and subsequent action of downstream components of the Pto signaling pathway. However, the possibility remains that the recognition of AvrPto in pepper plants may involve activities of other receptor like kinases (RLKs). The identification of the PLPKs in this study will serve as a foundation for further efforts to understand the roles of PLPKs in nonhost resistance. PMID:27536870

  13. Nanostructured clathrate phonon glasses: beyond the rattling concept.

    Science.gov (United States)

    He, Yuping; Galli, Giulia

    2014-05-14

    Using first-principles calculations, we investigated the thermoelectric properties of a newly synthesized Si-based ternary clathrate K8Al8Si38, composed of ∼1 nm hollow cages with a metal atom inside. This compound contains solely Earth abundant elements. We found that, similar to other nanostructured type I clathrates, this system is a semiconductor and has a low thermal conductivity (∼1 W/mK). It was long believed that the mere presence of rattling centers was responsible for the low lattice thermal conductivity of type I clathrates. We found instead that the cage structural disorder induced by atomic substitution plays a crucial role in determining the conductivity of these materials, in addition to the dynamics of the guest atoms. Our calculations showed that the latter is substantially affected by the charge transfer between the metal and the cages. Our results provide design rules for the search of new types of promising nanocage structured thermoelectric materials.

  14. Measurement of BSR noise of cockpit module materials for automobiles

    Science.gov (United States)

    Woo, C.; Park, H.

    2016-04-01

    Today, the interior noise perceived by occupants is becoming an important factor driving design standards for the design of most of interior assemblies in an automotive vehicles. BSR(Buzz, Squeak and Rattle) is a major contributor towards the perceived noise of annoyance to vehicle occupants. One method of minimizing the possibility of squeak and rattle is by making use of the judicious selection of mating materials pairs. In this paper, the BSR test system was designed and built. Also described is a test instrument that has been developed for such material pair compatibility studies.

  15. Comprehensive transcript profiling of Pto- and Prf-mediated host defense responses to infection by Pseudomonas syringae pv. tomato.

    Science.gov (United States)

    Mysore, Kirankumar S; Crasta, Oswald R; Tuori, Robert P; Folkerts, Otto; Swirsky, Peter B; Martin, Gregory B

    2002-11-01

    The disease resistance gene Pto encodes a serine/threonine protein kinase that confers resistance in tomato to Pseudomonas syringae pv. tomato strains that express the effector protein AvrPto. Pto-mediated resistance to bacterial speck disease also requires Prf, a protein with leucine-rich repeats and a putative nucleotide-binding site, although the role of Prf in the defense pathway is not known. We used GeneCalling, an open-architecture, mRNA-profiling technology, to identify genes that are either induced or suppressed in leaves 4 h after bacterial infection in the Pto- and Prf-mediated tomato-Pseudomonas(avrPto) interaction. Over 135 000 individual cDNA fragments representing an estimated 90% of the transcripts expressed in tomato leaves were examined and 432 differentially expressed genes were identified. The genes encode over 25 classes of proteins including 11 types of transcription factors and many signal transduction components. Differential expression of 91% of the genes required both Pto and Prf. Interestingly, differential expression of 32 genes did not require Pto but was dependent on Prf. Thus, our data support a role for Prf early in the Pto pathway and indicate that Prf can also function as an independent host recognition determinant of bacterial infection. Comprehensive expression profiling of the Pto-mediated defense response allows the development of many new hypotheses about the molecular basis of resistance to bacterial speck disease.

  16. Assessment of suspended dust from pipe rattling operations

    Science.gov (United States)

    Park, Ju-Myon

    Six types of aerosol samplers were evaluated experimentally in a test chamber with polydisperse fly ash. The Andersen sampler overestimates the mass of small particles due to particle bounce between stages and therefore provides a conservative estimate of respirable particulate mass and thoracic particulate mass. The TSP sampler provides an unbiased estimate of total particulate mass. TSP/CCM provides no information below ESD 2 mum and therefore underestimates respirable particulate mass. The PM10 sampler provides a reasonable estimate of the thoracic particulate fraction. The RespiCon sampler provides an unbiased estimate of respirable, thoracic, and inhalable fractions. DustTrak and SidePak monitors provide relative particle concentrations instead of absolute concentrations because it could not be calibrated for absolute particle concentrations with varying particle shape, composition, and density. Six sampler technologies were used to evaluate airborne dust concentrations released from oilfield pipe rattling operations. The task sampled was the removal of scale deposited on the inner wall of the pipe before it was removed from service in a producing well. The measured mass concentrations of the aerosol samplers show that a Gaussian plume model is applicable to the data of pipe rattling operations for finding an attainment area. It is estimated that workers who remain within 1 m of the machine centerline and directly downwind have an 8-hour TWA exposure opportunity of (13.3 +/- 9.7) mg/m3 for the Mud Lake pipe scale and (11.4 +/- 9.7) mg/m3 for the Lake Sand pipe scale at 95% confidence. At distances more than 4 m downwind from the machine centerline, dust concentrations are below the TWA-TLV of 10 mg/m3 for the worker in both scales. At positions crosswind or upwind from the machine centerline there is no measurable exposure. Available data suggest that the attainment area for the public starts at about 9 m downwind from the machine centerline in both scales, as

  17. Determining required valve performance for discrete control of PTO cylinders for wave energy

    DEFF Research Database (Denmark)

    Hansen, Rico Hjerm; Andersen, Torben Ole; Pedersen, Henrik C.

    2012-01-01

    Within wave energy a large challenge remains in designing a Power Take-Off (PTO) system capable of converting the slow oscillations induced by waves into electricity. Fluid power is an essential part of most PTO-concepts. To implement an efficient control of the load force produced by a cylinder...... on a floating body, throttle-less force control by discrete variation of the effective cylinder area has been investigated and found feasible for the Wavestar wave energy concept. However, the feasibility study assumes adequate valve performance, such that only the compression loss remains. This paper...

  18. Driveline Torsional Analysis and Clutch Damper Optimization for Reducing Gear Rattle

    Directory of Open Access Journals (Sweden)

    Huwei Wu

    2016-01-01

    Full Text Available This paper describes a research work on driveline modeling, torsional vibration analysis, and clutch damper parameters optimization for reducing transmission gear rattle on the vehicle creeping condition. Firstly, major driveline components, including quasi-transient engine, multistage stiffness clutch damper, detailed manual transmission and differential mechanism, and LuGre tire, are modeled, respectively. Secondly, powertrain system modeling adopting a two-stage stiffness clutch damper is constructed and analyzed. Transient responses predicted by the model show that the driveline undergoes severe torsional vibration and transmission gear rattle phenomenon. By analysis, it is concluded that the clutch damper works jumping between the first- and second-stage stiffness, which results in this problem for the creeping condition. Then, a three-stage stiffness clutch damper is proposed innovatively to solve this problem. It is shown that severe driveline vibration and gear rattle phenomenon are inhibited effectively. Finally, it draws a conclusion that clutch damper parameters could have a great effect on driveline vibration and gear rattle phenomenon and a three-stage stiffness clutch damper could be utilized to solve gear rattle phenomenon efficiently on the vehicle creeping condition.

  19. Direct determination of the ionization energies of PtC, PtO, and PtO2 with VUV radiation.

    Science.gov (United States)

    Citir, Murat; Metz, Ricardo B; Belau, Leonid; Ahmed, Musahid

    2008-10-02

    Photoionization efficiency curves were measured for gas-phase PtC, PtO, and PtO2 using tunable vacuum ultraviolet (VUV) radiation at the Advanced Light Source. The molecules were prepared by laser ablation of a platinum tube, followed by reaction with CH4 or N2O and supersonic expansion. These measurements provide the first directly measured ionization energy for PtC, IE(PtC) = 9.45 +/- 0.05 eV. The direct measurement also gives greatly improved ionization energies for the platinum oxides, IE(PtO) = 10.0 +/- 0.1 eV and IE(PtO2) = 11.35 +/- 0.05 eV. The ionization energy connects the dissociation energies of the neutral and cation, leading to greatly improved 0 K bond dissociation energies for the neutrals: D0(Pt-C) = 5.95 +/- 0.07 eV, D0(Pt-O) = 4.30 +/- 0.12 eV, and D0(OPt-O) = 4.41 +/- 0.13 eV, as well as enthalpies of formation for the gas-phase molecules DeltaH(0)(f,0)(PtC(g)) = 701 +/- 7 kJ/mol, DeltaH(0)(f,0)(PtO(g)) = 396 +/- 12 kJ/mol, and DeltaH(0)(f,0)(PtO2(g)) = 218 +/- 11 kJ/mol. Much of the error in previous Knudsen cell measurements of platinum oxide bond dissociation energies is due to the use of thermodynamic second law extrapolations. Third law values calculated using statistical mechanical thermodynamic functions are in much better agreement with values obtained from ionization energies and ion energetics. These experiments demonstrate that laser ablation production with direct VUV ionization measurements is a versatile tool to measure ionization energies and bond dissociation energies for catalytically interesting species such as metal oxides and carbides.

  20. The N-terminal domain of the tomato immune protein Prf contains multiple homotypic and Pto kinase interaction sites.

    Science.gov (United States)

    Saur, Isabel Marie-Luise; Conlan, Brendon Francis; Rathjen, John Paul

    2015-05-01

    Resistance to Pseudomonas syringae bacteria in tomato (Solanum lycopersicum) is conferred by the Prf recognition complex, composed of the nucleotide-binding leucine-rich repeats protein Prf and the protein kinase Pto. The complex is activated by recognition of the P. syringae effectors AvrPto and AvrPtoB. The N-terminal domain is responsible for Prf homodimerization, which brings two Pto kinases into close proximity and holds them in inactive conformation in the absence of either effector. Negative regulation is lost by effector binding to the catalytic cleft of Pto, leading to disruption of its P+1 loop within the activation segment. This change is translated through Prf to a second Pto molecule in the complex. Here we describe a schematic model of the unique Prf N-terminal domain dimer and its interaction with the effector binding determinant Pto. Using heterologous expression in Nicotiana benthamiana, we define multiple sites of N domain homotypic interaction and infer that it forms a parallel dimer folded centrally to enable contact between the N and C termini. Furthermore, we found independent binding sites for Pto at either end of the N-terminal domain. Using the constitutively active mutant ptoL205D, we identify a potential repression site for Pto in the first ∼100 amino acids of Prf. Finally, we find that the Prf leucine-rich repeats domain also binds the N-terminal region, highlighting a possible mechanism for transfer of the effector binding signal to the NB-LRR regulatory unit (consisting of a central nucleotide binding and C-terminal leucine-rich repeats). © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

  1. The N-Terminal Domain of the Tomato Immune Protein Prf Contains Multiple Homotypic and Pto Kinase Interaction Sites*

    Science.gov (United States)

    Saur, Isabel Marie-Luise; Conlan, Brendon Francis; Rathjen, John Paul

    2015-01-01

    Resistance to Pseudomonas syringae bacteria in tomato (Solanum lycopersicum) is conferred by the Prf recognition complex, composed of the nucleotide-binding leucine-rich repeats protein Prf and the protein kinase Pto. The complex is activated by recognition of the P. syringae effectors AvrPto and AvrPtoB. The N-terminal domain is responsible for Prf homodimerization, which brings two Pto kinases into close proximity and holds them in inactive conformation in the absence of either effector. Negative regulation is lost by effector binding to the catalytic cleft of Pto, leading to disruption of its P+1 loop within the activation segment. This change is translated through Prf to a second Pto molecule in the complex. Here we describe a schematic model of the unique Prf N-terminal domain dimer and its interaction with the effector binding determinant Pto. Using heterologous expression in Nicotiana benthamiana, we define multiple sites of N domain homotypic interaction and infer that it forms a parallel dimer folded centrally to enable contact between the N and C termini. Furthermore, we found independent binding sites for Pto at either end of the N-terminal domain. Using the constitutively active mutant ptoL205D, we identify a potential repression site for Pto in the first ∼100 amino acids of Prf. Finally, we find that the Prf leucine-rich repeats domain also binds the N-terminal region, highlighting a possible mechanism for transfer of the effector binding signal to the NB-LRR regulatory unit (consisting of a central nucleotide binding and C-terminal leucine-rich repeats). PMID:25792750

  2. Who's your neighbor? Acoustic cues to individual identity in red squirrel Tamiasciurus hudsonicus rattle calls

    Directory of Open Access Journals (Sweden)

    Shannon M. DIGWEED, Drew RENDALL, Teana IMBEAU

    2012-10-01

    Full Text Available North American red squirrels Tamiasciurus hudsonicus often produce a loud territorial rattle call when conspecifics enter or invade a territory. Previous playback experiments suggest that the territorial rattle call may indicate an invader's identity as squirrels responded more intensely to calls played from strangers than to calls played from neighbors. This dear-enemy effect is well known in a variety of bird and mammal species and functions to reduce aggressive interactions between known neighbors. However, although previous experiments on red squirrels suggest some form of individual differentiation and thus recognition, detailed acoustic analysis of potential acoustic cues in rattle calls have not been conducted. If calls function to aid in conspecific identification in order to mitigate aggressive territorial interactions, we would expect that individual recognition cues would be acoustically represented. Our work provides a detailed analysis of acoustic cues to identity within rattle calls. A total of 225 calls across 32 individual squirrels from Sheep River Provincial Park, Kananaskis, AB, Canada, were analyzed with discriminant function analysis for potential acoustic cues to individual identity. Initial analysis of all individuals revealed a reliable acoustic differentiation across individuals. A more detailed analysis of clusters of neighboring squirrels was performed and results again indicated a statistically significant likelihood that calls were assigned correctly to specific squirrels (55%-75% correctly assigned; in other words squirrels have distinct voices that should allow for individual identification and discrimination by conspecifics [Current Zoology 58 (5: 758–764, 2012].

  3. Who's your neighbor? Acoustic cues to individual identity in red squirrel Tamiasciurus hudsonicus rattle calls

    Institute of Scientific and Technical Information of China (English)

    Shannon M.DIGWEED; Drew RENDALL; Teana IMBEAU

    2012-01-01

    North American red squirrels Tamiasciurus hudsonicus often produce a loud territorial rattle call when conspecifics enter or invade a territory.Previous playback experiments suggest that the territorial rattle call may indicate an invader's identity as squirrels responded more intensely to calls played from strangers than to calls played from neighbors.This dear-enemy effect is well known in a variety of bird and mammal species and functions to reduce aggressive interactions between known neighbors.However,although previous experiments on red squirrels suggest some form of individual differentiation and thus recognition,detailed acoustic analysis of potential acoustic cues in rattle calls have not been conducted.If calls function to aid in conspecific identification in order to mitigate aggressive territorial interactions,we would expect that individual recognition cues would be acoustically represented.Our work provides a detailed analysis of acoustic cues to identity within rattle calls.A total of 225 calls across 32 individual squirrels from Sheep River Provincial Park,Kananaskis,AB,Canada,were analyzed with discriminant function analysis for potential acoustic cues to individual identity.Initial analysis of all individuals revealed a reliable acoustic differentiation across individuals.A more detailed analysis of clusters of neighboring squirrels was performed and results again indicated a statistically significant likelihood that calls were assigned correctly to specific squirrels (55%-75% correctly assigned); in other words squirrels have distinct voices that should allow for individual identification and discrimination by conspecifics.

  4. Growth and morphology of a 4PtO 6 crystals

    Science.gov (United States)

    Ohsato, H.; Sugimura, T.; Kageyama, K.

    1981-01-01

    Single crystals of Ca 4PtO 6 were precipitated from molten CaCl 2 in a wet atmosphere at 800-1000°C. Above 900°C, CaO single crystals coexisted. The Ca 4PtO 6 crystals obtained were transparent with pale brown or pale yellow colour, and were mostly granular, about 1 mm in size. The crystal habit was a combination of the {112¯0}, {101¯0}, {101¯2}, {011¯1} and {202¯1} cryst al faces. Some prismatic crystals were found, 2 mm long and 0.1 mm wide. They were found to be twinned with the (10-0) plane. The crystal has a trigonal unit cell with a = 9.332 Å, c = 11.26 Å; and with six formula units of which the space group is R—c. It is uniaxial positive with refractive indices 1.85 hydrochloric acid. The growth mechanism of Ca 4PtO 6 crystals was also discussed.

  5. One-pot fabrication of rattle-like capsules with multicores by pickering-based polymerization with nanoparticle nucleation.

    Science.gov (United States)

    Zou, Shengwen; Hu, Yang; Wang, Chaoyang

    2014-08-01

    Rattle-like polymer capsules with multicores in one shell are facilely fabricated by oil-in-water Pickering emulsion polymerization for the first time. The oil phase contains hydrophobic silica nanoparticles dispersed in polymerizable monomer, styrene, and unpolymerizable solvent, hexadecane. The multicore rattle-like capsules are facilely produced after the polymerization of monomers in the oil droplets. The key point of this one-pot method lies in the nucleation of hydrophobic silica and the phase separation between the resulting polystyrene and hexadecane. The influences of the contents of silica, hexadecane, cross-linker, and stabilizer on the structure and morphology of rattle-like capsules are systematically investigated. Moreover, functionalization of the rattle-like capsules can be developed easily by varying hydrophobic nucleation nanoparticles in the oil phase. This work opens up a new route to fabricate multilevel capsules or spheres. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Association studies in Populus tomentosa reveal the genetic interactions of Pto-MIR156c and its targets in wood formation

    Directory of Open Access Journals (Sweden)

    Mingyang Quan

    2016-08-01

    Full Text Available MicroRNAs (miRNAs regulate gene expression in many biological processes, but the significance of the interaction between a miRNA and its targets in perennial trees remains largely unknown. Here, we employed transcript profiling and association studies in Populus tomentosa (Pto to decipher the effect of genetic variation and interactions between Pto-miR156c and its potential targets (Pto-SPL15, Pto-SPL20, and Pto-SPL25 in 435 unrelated individuals from a natural population of P. tomentosa. Single-SNP (single-nucleotide polymorphism based association studies with analysis of the underlying additive and dominant effects identified 69 significant associations (P 0.05 from Pto-MIR156c and its three potential targets, with six wood and growth traits, revealing their common roles in wood formation. Epistasis analysis uncovered 129 significant SNP-SNP associations with ten traits, indicating the potential genetic interactions of Pto-MIR156c and its three putative targets. Interestingly, expression analysis in stem (phloem, cambium, and xylem revealed that Pto-miR156c expression showed strong negative correlations with Pto-SPL20 (r = -0.90, P < 0.01 and Pto-SPL25 (r = -0.65, P < 0.01, and a positive correlation with Pto-SPL15 (r = 0.40, P < 0.01, which also indicated the putative interactions of Pto-miR156c and its potential targets and their common roles in wood formation. Thus, our study provided an alternative approach to decipher the interaction between miRNAs and their targets and to dissect the genetic architecture of complex traits in trees.

  7. PtoMYB156 is involved in negative regulation of phenylpropanoid metabolism and secondary cell wall biosynthesis during wood formation in poplar

    Science.gov (United States)

    Yang, Li; Zhao, Xin; Ran, Lingyu; Li, Chaofeng; Fan, Di; Luo, Keming

    2017-01-01

    Some R2R3 MYB transcription factors have been shown to be major regulators of phenylpropanoid biosynthetic pathway and impact secondary wall formation in plants. In this study, we describe the functional characterization of PtoMYB156, encoding a R2R3-MYB transcription factor, from Populus tomentosa. Expression pattern analysis showed that PtoMYB156 is widely expressed in all tissues examined, but predominantly in leaves and developing wood cells. PtoMYB156 localized to the nucleus and acted as a transcriptional repressor. Overexpression of PtoMYB156 in poplar repressed phenylpropanoid biosynthetic genes, leading to a reduction in the amounts of total phenolic and flavonoid compounds. Transgenic plants overexpressing PtoMYB156 also displayed a dramatic decrease in secondary wall thicknesses of xylem fibers and the content of cellulose, lignin and xylose compared with wild-type plants. Transcript accumulation of secondary wall biosynthetic genes was down-regulated by PtoMYB156 overexpression. Transcriptional activation assays revealed that PtoMYB156 was able to repress the promoter activities of poplar CESA17, C4H2 and GT43B. By contrast, knockout of PtoMYB156 by CRISPR/Cas9 in poplar resulted in ectopic deposition of lignin, xylan and cellulose during secondary cell wall formation. Taken together, these results show that PtoMYB156 may repress phenylpropanoid biosynthesis and negatively regulate secondary cell wall formation in poplar. PMID:28117379

  8. Granular Media under Vibration in Zero Gravity: Transition from Rattling to Granular Gas

    CERN Document Server

    Evesque, P; Zhai, G; Hou, M

    2011-01-01

    We report on different experimental behaviours of granular dissipative matter excited by vibration as studied during the 43rd ESA campaign of Airbus A300-0g from CNES. The effect of g-jitter is quantified through the generation of a rattle effect. The French-European team's electromagnetic set-up is used, with 20Hz cam recording and high speed camera for a short duration (1s) during each parabola.

  9. Initial RattleSnake Calculations of the Hot Zero Power BEAVRS

    Energy Technology Data Exchange (ETDEWEB)

    M. Ellis; J. Ortensi; Y. Wang; K. Smith; R.C. Martineau

    2014-01-01

    The validation of the Idaho National Laboratory's next generation of reactor physics analysis codes is an essential and ongoing task. The validation process requires a large undertaking and includes detailed, realistic models that can accurately predict the behavior of an operational nuclear reactor. Over the past few years the INL has developed the RattleSnake application and supporting tools on the MOOSE framework to perform these reactor physics calculations. RattleSnake solves the linearized Boltzmann transport equation with a variety of solution meth­ ods. Various traditional reactor physics benchmarks have already been performed, but a more realistic light water reactor comparison was needed to solidify the status of the code and deter­ mine its fidelity. The INL team decided to use the Benchmark for Evaluation and Validation of Reactor Simulations, which was made available in early 2013. This benchmark is a one­ of-a-kind document assembled by the Massachusetts Institute of Technology, which includes two cycles of detailed, measured PWR operational data. The results from this initial study of the hot zero power conditions show the current INL analysis procedure with DRAGON4 cross section preparation and using the low order diffusion solver in RattleSnake for the whole core calculations yield very encouraging results for PWR analysis. The radial assembly power distributions, radial detector measurements and control rod worths were computed with good accuracy. The computation of the isothermal temperature coefficients of reactivity require further study.

  10. Study of the reaction $\\gamma p\\to p\\pi^0\\eta$

    CERN Document Server

    Horn, I; Anton, G; Bantes, R; Bartholomy, O; Beck, R; Beloglazov, Y; Bogendorfer, R; Castelijns, R; Cred, V; Ehmanns, A; Ernst, J; Fabry, I; Flemming, H; Fsel, A; Fuchs, M; Funke, C; Gothe, R; Gridnev, A; Gutz, E; Hoffgen, S; Hol, J; Junkersfeld, J; Kalinowsky, H; Klein, F; Klempt, E; Koch, H; Konrad, M; Kopf, B; Krusche, B; Langheinrich, J; Löhner, H; Lopatin, I; Lotz, J; Matthy, H; Menze, D; Messchendorp, J; Metag, V; Nikonov, V A; Novinski, D; Ostrick, M; Van Pee, H; Radkov, A; Sarantsev, A V; Schmidt, C; Schmieden, H; Schoch, B; Suft, G; Sumachev, V; Szczepanek, T; Thoma, U; Walther, D; Weinheimer, C

    2008-01-01

    The reaction $\\gamma p\\to p\\pi^0\\eta$ has been studied with the CBELSA detector at the tagged photon beam of the Bonn electron stretcher facility. The reaction shows contributions from $\\Delta^+(1232)\\eta$, $N(1535)^+\\pi^0$ and $pa_0(980)$ as intermediate states. A partial wave analysis suggests that the reaction proceeds via formation of six $\\Delta$ resonances, $\\Delta(1600)P_{33}$, $\\Delta(1920)P_{33}$, $\\Delta(1700)D_{33}$, $\\Delta(1940)D_{33}$, $\\Delta(1905)F_{35}$, $\\Delta(2360)D_{33}$, and two nucleon resonances $N(1880)P_{11}$ and $N(2200)P_{13}$, for which pole positions and decay branching ratios are given.

  11. Chemical template-assisted synthesis of monodisperse rattle-type Fe3O4@C hollow microspheres as drug carrier.

    Science.gov (United States)

    Cheng, Lin; Ruan, Weimin; Zou, Bingfang; Liu, Yuanyuan; Wang, Yongqiang

    2017-08-01

    A chemical template strategy was put forward to synthesize monodisperse rattle-type magnetic carbon (Fe3O4@C) hollow microspheres. During the synthesis procedure, monodisperse Fe2O3 microspheres were used as chemical template, which released Fe(3+) ions in acidic solution and initiated the in-situ polymerization of pyrrole into polypyrrole (PPy) shell. With the continual acidic etching of Fe2O3 microspheres, rattle-type Fe2O3@PPy microspheres were generated with the cavity appearing between the PPy shell and left Fe2O3 core, which were then transformed into Fe3O4@C hollow microspheres through calcination in nitrogen atmosphere. Compared with traditional physical template, the shell and cavity of rattle-type hollow microspheres were generated in one step using the chemical template method, which obviously saved the complex procedures including the coating and removal of middle shells. The experimental results exhibited that the rattle-type Fe3O4@C hollow microspheres with different parameters could be regulated through controlled synthesis of the intermediate Fe2O3@PPy product. Moreover, when the rattle-type Fe3O4@C hollow microspheres were investigated as drug carrier, they manifested sustained-release behaviour of doxorubicin, justifying their promising applications as carriers in drug delivery. The aim of the present study was first to synthesize rattle-type Fe3O4@C hollow microspheres through a simple synthesis method as a drug carrier. Here a chemical template synthesis of rattle-type hollow microspheres was developed, which saved the complex procedures including the coating and removal of middle shells in traditional physical template. Second, all the influence factors in the reaction processes were systematically investigated to obtain rattle-type Fe3O4@C hollow microspheres with controlled parameters. Third, the rattle-type Fe3O4@C hollow microspheres were studied as drug carriers and the influences of their structural parameters on drug loading and

  12. A tomato LysM receptor-like kinase promotes immunity and its kinase activity is inhibited by AvrPtoB.

    Science.gov (United States)

    Zeng, Lirong; Velásquez, André C; Munkvold, Kathy R; Zhang, Jingwei; Martin, Gregory B

    2012-01-01

    Resistance in tomato (Solanum lycopersicum) to infection by Pseudomonas syringae involves both detection of pathogen-associated molecular patterns (PAMPs) and recognition by the host Pto kinase of pathogen effector AvrPtoB which is translocated into the host cell and interferes with PAMP-triggered immunity (PTI). The N-terminal portion of AvrPtoB is sufficient for its virulence activity and for recognition by Pto. An amino acid substitution in AvrPtoB, F173A, abolishes these activities. To investigate the mechanisms of AvrPtoB virulence, we screened for tomato proteins that interact with AvrPtoB and identified Bti9, a LysM receptor-like kinase. Bti9 has the highest amino acid similarity to Arabidopsis CERK1 among the tomato LysM receptor-like kinases (RLKs) and belongs to a clade containing three other tomato proteins, SlLyk11, SlLyk12, and SlLyk13, all of which interact with AvrPtoB. The F173A substitution disrupts the interaction of AvrPtoB with Bti9 and SlLyk13, suggesting that these LysM-RLKs are its virulence targets. Two independent tomato lines with RNAi-mediated reduced expression of Bti9 and SlLyk13 were more susceptible to P. syringae. Bti9 kinase activity was inhibited in vitro by the N-terminal domain of AvrPtoB in an F173-dependent manner. These results indicate Bti9 and/or SlLyk13 play a role in plant immunity and the N-terminal domain of AvrPtoB may have evolved to interfere with their kinase activity. Finally, we found that Bti9 and Pto interact with AvrPtoB in a structurally similar although not identical fashion, suggesting that Pto may have evolved as a molecular mimic of LysM-RLK kinase domains. © 2011 The Authors. The Plant Journal © 2011 Blackwell Publishing Ltd.

  13. Quantification of the effects of audible rattle and source type on the human response to environmental vibration.

    Science.gov (United States)

    Woodcock, J; Sica, G; Peris, E; Sharp, C; Moorhouse, A T; Waddington, D C

    2016-03-01

    The present research quantifies the influence of source type and the presence of audible vibration-induced rattle on annoyance caused by vibration in residential environments. The sources of vibration considered are railway and the construction of a light rail system. Data were measured in the United Kingdom using a socio-vibration survey (N = 1281). These data are analyzed using ordinal logit models to produce exposure-response relationships describing community annoyance as a function of vibration exposure. The influence of source type and the presence of audible vibration-induced rattle on annoyance are investigated using dummy variable analysis, and quantified using odds-ratios and community tolerance levels. It is concluded that the sample population is more likely to express higher levels of annoyance if the vibration source is construction compared to railway, and if vibration-induced rattle is audible.

  14. AvrPtoB targets the LysM receptor kinase CERK1 to promote bacterial virulence on plants.

    Science.gov (United States)

    Gimenez-Ibanez, Selena; Hann, Dagmar R; Ntoukakis, Vardis; Petutschnig, Elena; Lipka, Volker; Rathjen, John P

    2009-03-10

    Plant innate immunity relies on a set of pattern recognition receptors (PRRs) that respond to ligands known as pathogen-associated molecular patterns (PAMPs). To overcome such immunity, phytopathogenic bacteria deliver virulence molecules called effector proteins into the plant cell that collectively promote pathogenesis. The vast majority of PRRs controlling PAMP-triggered immunity (PTI) and the mechanisms used by specific effectors to suppress these pathways are mostly unknown. Here, we show that the Arabidopsis LysM receptor kinase CERK1, which is critical for chitin elicitor signaling and resistance to fungal pathogens, plays an essential role in restricting bacterial growth on plants. This is supported by the fact that CERK1 is a target of the bacterial type III effector protein AvrPtoB, which blocks all defense responses through this receptor. AvrPtoB ubiquitinates the CERK1 kinase domain in vitro and targets CERK1 for degradation in vivo. We show that CERK1 is a determinant of bacterial immunity, but its contribution is overcome by bacteria expressing AvrPtoB. Our results reveal a new pathway for plant immunity against bacteria and a role for AvrPtoB E3-ligase activity in suppressing PTI.

  15. Allelic variation in PtoPsbW associated with photosynthesis, growth, and wood properties in Populus tomentosa.

    Science.gov (United States)

    Wang, Longxin; Wang, Bowen; Du, Qingzhang; Chen, Jinhui; Tian, Jiaxing; Yang, Xiaohui; Zhang, Deqiang

    2017-02-01

    Photosynthesis is one of the most important reactions on earth. PsbW, a nuclear-encoded subunit of photosystem II (PSII), stabilizes PSII structure and plays an important role in photosynthesis. Here, we used candidate gene-based linkage disequilibrium (LD) mapping to detect significant associations between allelic variations of PtoPsbW and traits related to photosynthesis, growth, and wood properties in Populus tomentosa. PtoPsbW showed the highest expression in leaves and it increased during the development of these leaves, suggesting that PtoPsbW may play an important role in plant growth and development. Analysis of nucleotide diversity and LD revealed that PtoPsbW has low single-nucleotide polymorphism (SNP) diversity (π tot = 0.0048 and θ w = 0.0050) and relatively low average value of LD (0.1500), indicating that PtoPsbW is conserved due to its indispensable function. Using single-SNP associations in an association population of 435 individuals, we identified five significant associations at the threshold of P ≤ 0.05, explaining 3.28-15.98 % of the phenotypic variation. Haplotype-based association analyses indicated that 13 haplotypes (P ≤ 0.05) from six blocks were associated with photosynthesis, growth, and wood properties. Our work shows that identifying allelic variation and LD can help to decipher the genetic basis of photosynthesis and could potentially be applied for molecular marker-assisted selection in Populus.

  16. The changing of the guard: the Pto/Prf receptor complex of tomato and pathogen recognition.

    Science.gov (United States)

    Ntoukakis, Vardis; Saur, Isabel M L; Conlan, Brendon; Rathjen, John P

    2014-08-01

    One important model for disease resistance is the Prf recognition complex of tomato, which responds to different bacterial effectors. Prf incorporates a protein kinase called Pto as its recognition domain that mimics effector virulence targets, and activates resistance after interaction with specific effectors. Recent findings show that this complex is oligomeric, and reveal how this impacts mechanism. Oligomerisation brings two or more kinases into proximity, where they can phosphorylate each other after effector perception. Effector attack on one kinase activates another in trans, constituting a molecular trap for the effector. Oligomerisation of plant resistance proteins may be a general concept that broadens pathogen recognition and restricts the ability of pathogens to evolve virulence. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Synthesis of Magnetic Rattle-Type Silica with Controllable Magnetite and Tunable Size by Pre-Shell-Post-Core Method.

    Science.gov (United States)

    Chen, Xue; Tan, Longfei; Meng, Xianwei

    2016-03-01

    In this study, we have developed the pre-shell-post-core route to synthesize the magnetic rattle-type silica. This method has not only simplified the precursor's process and reduced the reacting time, but also ameliorated the loss of magnetite and made the magnetite content and the inner core size controllable and tunable. The magnetite contents and inner core size can be easily controlled by changing the type and concentration of alkali, reaction system and addition of water. The results show that alkali aqueous solution promotes the escape of the precursor iron ions from the inner space of rattle-type silica and results in the loss of magnetite. In this case, NaOH ethanol solution is better for the formation of magnetite than ammonia because it not only offers an appropriate alkalinity to facilitate the synthesis of. magnetic particles, but also avoids the escape of the iron ions from the mesopores of rattle-type silica. The synthesis process is very simple and efficient, and it takes no more than 2 hours to complete the total preparation and handling of the magnetic rattle-type silica. The end-product Fe3O4@SiO2 nanocomposites also have good magnetic properties which will perform potential application in biomedical science.

  18. Utilization of a tobacco rattle virus vector to clone an Nicotiana benthamiana cDNA library for VIGS

    Science.gov (United States)

    Virus-induced gene silencing (VIGS) is an efficient and rapid method to identify plant gene functions. One of the most widely used VIGS vectors is Tobacco rattle virus (TRV) which has been used successfully for RNA interference (RNAi) in N. benthamiana and tomato. We previously modified a TRV VIGS v...

  19. Effect of green manure crops and organic amendments on incidence of nematode-borne tobacco rattle virus

    NARCIS (Netherlands)

    Zoon, F.C.; Bruggen, van A.H.C.; Heij, de A.; Asjes, C.J.; Ende, van den J.E.

    2002-01-01

    Tobacco rattle tobravirus (TRV) may infect several ornamental bulb crops and is transmitted by trichodorid nematodes. Paratrichodorus teres, P. pachydermus and Trichodorus similis are the main vectors in the Netherlands. In field experiments the effects of various pre-crops and organic amendments on

  20. Objective evaluation of subjective noise impressions; Objektivierung subjektiver Geraeuschbeurteilungen

    Energy Technology Data Exchange (ETDEWEB)

    Pischinger, S.; Hoppermanns, J. [RWTH Aachen (DE). Lehrstuhl fuer Verbrennungskraftmaschinen (VKA); Lange, B. [Opel GmbH, Ruesselsheim (Germany); Heuer, S. [FEV Motorentechnik GmbH, Aachen (Germany)

    2006-11-15

    Internal combustion engines are becoming ever more quiet. However, the more quiet an engine is overall, the more individual disturbing noise shares become conspicuous. These noise shares include diesel engine knocking, injector ticking or rattling and gear drive howling. The degree of annoyance of these disturbing noise shares cannot be adequately described by the noise level. To achieve an efficient evaluation of disturbing noise shares, acoustical characteristic values such as impulsiveness or tonality must be considered. In the research work described in this paper, characteristic values were developed for frequently complained about engine noises. These so called objective parameters rate the disturbing noises on a scale from 1 to 10. The work was carried out on behalf of the Forschungsvereinigung Verbrennungskraftmaschinen e.V. (FVV) at the Institute for Internal Combustion Engines (VKA) of the Aachen University of Technology (RWTH Aachen). (orig.)

  1. PtoP融资模式及其对银行业的冲击——以Zopa和Prosper互助借贷平台为例%PtoP financing mode and it's impact on banking

    Institute of Scientific and Technical Information of China (English)

    何崇阳

    2007-01-01

    PtoP是指“Peer-to-peer”或“person-to-person”,即指个人对个人。这种新型的融资模式已经在欧美市场取得了极大的成功,它的诞生更进一步地佐证了比尔·盖茨的“恐龙论”。

  2. Shake, Rattle and Roll Horror Franchise and the Specter of Nation-Formation in the Philippines

    Directory of Open Access Journals (Sweden)

    Rolando B. Tolentino

    2016-06-01

    Full Text Available The paper looks into the most successful horror franchise in Philippine history. Shake, Rattle and Roll has had a successful 14-film run since its introduction in 1984, and is composed of a three-part segment, each tackling a horrific experience: ghosts and folk creatures in provincial and city settings. My paper maps out the narratives, and the social and political contexts of the series. Specif ically, the period beginning 1984 marks a series of national transition: the political crisis of the Marcoses, People Power 1, the rise of Corazon Aquino, the economic crises in 1997 and 2007, the ousting of Joseph Estrada, the rise of neoliberalism, the coming of Noynoy Aquino, and the incarceration of Gloria Arroyo. How might these films also be read as analog of the anxieties of the nation?

  3. Intermittent gear rattle due to interactions between forcing and manufacturing errors

    Science.gov (United States)

    Ottewill, James R.; Neild, Simon A.; Wilson, R. Eddie

    2009-04-01

    The interaction between eccentricity and an external forcing fluctuation in gear rattle response is investigated experimentally. The experimental rig consists of a 1:1 ratio steel spur gear pair, the input gear being controlled in displacement and the output gear being under no load. Gear transmission errors recorded using high accuracy encoders are presented. Large variations in backlash oscillation amplitude are observed as the relative phase of the input forcing and the sinusoidal static transmission error due to eccentricity is varied. A simplified mathematical model incorporating eccentricity is developed. It is compared with experimental findings for three different gear eccentricity alignments by way of plots relating backlash oscillation amplitude to forcing amplitude and phase relative to eccentricity sinusoid. It is shown that eccentricity does not fully account for the experimentally observed large variations in amplitude. Through analysis of the experimental data, it is suggested that further tooth profiling errors may explain the discrepancies.

  4. Search for Narrow Nucleon Resonance in $\\gamma p\\to \\eta p$

    CERN Document Server

    Anisovich, A V; Kuznetsov, V; Nikonov, V A; Polyakov, M V; Sarantsev, A V; Thoma, U

    2011-01-01

    Results of a partial wave analysis of new high-statistics data on $\\gamma p\\to p\\eta$ from MAMI are presented. A fit using known broad resonances and only standard background amplitudes can not describe the relatively narrow peaking structure in the cross section in the mass region of 1660-1750 MeV which follows a minimum. An improved description of the data can be reached by either assuming the existence of a narrow resonance at a mass of about 1700 MeV with small photo-coupling or by a threshold effect. In the latter case the observed structure is explained by a strong (resonant or non-resonant) $\\gamma p\\to\\omega p$ coupling in the $S_{11}$ partial wave. When the beam asymmetry data, published by part of the GRAAL collaboration, are included in the fit, the solution with a narrow $P_{11}$ state is slightly preferred. In that fit, mass and width of the hypothetical resonance are determined to $M\\sim$1694 MeV and $\\Gamma\\sim 40$ MeV, respectively, and the photo-coupling to $\\sqrt{{\\rm Br}_{\\eta N}} A_{1/2}^p...

  5. New fits to the reaction $\\gamma p\\to K^+\\Lambda$

    CERN Document Server

    de la Puente, Alejandro; Raue, Brian A

    2008-01-01

    The reaction $\\gamma p\\to K^+\\Lambda$ has been investigated over the center-of-momentum energy, $W$, range from threshold up to 2.6 GeV in a tree-level effective Lagrangian model that incorporates most of the well-established baryon resonances with spins equal to or below 5/2. Four less less well-established nucleon resonances of higher mass are also included. The fitted parameters consist, for each resonance included, of the products of the coupling strengths at the electromagnetic and strong interaction vertices and, for the less-established nucleon resonances, the total decay width. For the well-established nucleon resonances, the energy and momentum dependence of the widths is treated within a dynamical model that is normalized to give the empirical decay branching ratios on the resonance mass shells. For the less-established resonances, the total decay width is a single parameter independent of the reaction kinematics. The model is used to fit the most recent CLAS data for the unpolarized differential cr...

  6. Effect of green manure crops and organic amendments on incidence of nematode-borne tobacco rattle virus

    OpenAIRE

    Zoon, F.C.; Bruggen, van, A.S.; Heij, de, W.J.A.; Asjes, C.J.; Ende, van den, J.

    2002-01-01

    Tobacco rattle tobravirus (TRV) may infect several ornamental bulb crops and is transmitted by trichodorid nematodes. Paratrichodorus teres, P. pachydermus and Trichodorus similis are the main vectors in the Netherlands. In field experiments the effects of various pre-crops and organic amendments on the TRV Infection Potential of Soils (TRV-IPS) and on disease level in tulip and gladiolus were studied. Organic matter amendment of soil at a rate of 1% dry weight has been shown to reduce the ho...

  7. The Origin of Ultralow Thermal Conductivity in InTe: Lone-Pair-Induced Anharmonic Rattling.

    Science.gov (United States)

    Jana, Manoj K; Pal, Koushik; Waghmare, Umesh V; Biswas, Kanishka

    2016-06-27

    Understanding the origin of intrinsically low thermal conductivity is fundamentally important to the development of high-performance thermoelectric materials, which can convert waste-heat into electricity. Herein, we report an ultralow lattice thermal conductivity (ca. 0.4 W m(-1)  K(-1) ) in mixed valent InTe (that is, In(+) In(3+) Te2 ), which exhibits an intrinsic bonding asymmetry with coexistent covalent and ionic substructures. The phonon dispersion of InTe exhibits, along with low-energy flat branches, weak instabilities associated with the rattling vibrations of In(+) atoms along the columnar ionic substructure. These weakly unstable phonons originate from the 5s(2) lone pair of the In(+) atom and are strongly anharmonic, which scatter the heat-carrying acoustic phonons through strong anharmonic phonon-phonon interactions, as evident in anomalously high mode Grüneisen parameters. A maximum thermoelectric figure of merit (z T) of about 0.9 is achieved at 600 K for the 0.3 mol % In-deficient sample, making InTe a promising material for mid-temperature thermoelectric applications.

  8. Noise suppression by noise

    OpenAIRE

    Vilar, J. M. G.; Rubí Capaceti, José Miguel

    2001-01-01

    We have analyzed the interplay between an externally added noise and the intrinsic noise of systems that relax fast towards a stationary state, and found that increasing the intensity of the external noise can reduce the total noise of the system. We have established a general criterion for the appearance of this phenomenon and discussed two examples in detail.

  9. 探究木摇铃的发声原理%Investigations on the sound-production mechanism of wooden rattle

    Institute of Scientific and Technical Information of China (English)

    莫滨

    2013-01-01

    Wooden rattle is a kind of old toy .The current explanation of its sound-production mechanism is incorrect .By making suitable changes of the wooden rattle ,a series of experiments were carried out to investigate in what situations it could produce sound .The results showed that sound was produced by the friction between the knot and the bar of the wooden rattle .%通过研究发现文献中的木摇铃发声原理的观点是错误的。适当改变木摇铃的器材,通过一系列实验,观察其在不同情况下是否发声,证实其发声源于绳结与木棍之间的摩擦振动。

  10. Efficient gene silencing mediated by tobacco rattle virus in an emerging model plant physalis.

    Directory of Open Access Journals (Sweden)

    Ji-Si Zhang

    Full Text Available The fruit of Physalis has a berry and a novelty called inflated calyx syndrome (ICS, also named the 'Chinese lantern'. Elucidation of the underlying developmental mechanisms of fruit diversity demands an efficient gene functional inference platform. Here, we tested the application of the tobacco rattle virus (TRV-mediated gene-silencing system in Physalis floridana. First, we characterized the putative gene of a phytoene desaturase in P. floridana (PfPDS. Infecting the leaves of the Physalis seedlings with the PfPDS-TRV vector resulted in a bleached plant, including the developing leaves, floral organs, ICS, berry, and seed. These results indicated that a local VIGS treatment can efficiently induce a systemic mutated phenotype. qRT-PCR analyses revealed that the bleaching extent correlated to the mRNA reduction of the endogenous PfPDS. Detailed comparisons of multiple infiltration and growth protocols allowed us to determine the optimal methodologies for VIGS manipulation in Physalis. We subsequently utilized this optimized VIGS methodology to downregulate the expression of two MADS-box genes, MPF2 and MPF3, and compared the resulting effects with gene-downregulation mediated by RNA interference (RNAi methods. The VIGS-mediated gene knockdown plants were found to resemble the mutated phenotypes of floral calyx, fruiting calyx and pollen maturation of the RNAi transgenic plants for both MPF2 and MPF3. Moreover, the two MADS-box genes were appeared to have a novel role in the pedicel development in P. floridana. The major advantage of VIGS-based gene knockdown lies in practical aspects of saving time and easy manipulation as compared to the RNAi. Despite the lack of heritability and mosaic mutation phenotypes observed in some organs, the TRV-mediated gene silencing system provides an alternative efficient way to infer gene function in various developmental processes in Physalis, thus facilitating understanding of the genetic basis of the evolution

  11. Efficient gene silencing mediated by tobacco rattle virus in an emerging model plant physalis.

    Science.gov (United States)

    Zhang, Ji-Si; Zhao, Jing; Zhang, Shaohua; He, Chaoying

    2014-01-01

    The fruit of Physalis has a berry and a novelty called inflated calyx syndrome (ICS, also named the 'Chinese lantern'). Elucidation of the underlying developmental mechanisms of fruit diversity demands an efficient gene functional inference platform. Here, we tested the application of the tobacco rattle virus (TRV)-mediated gene-silencing system in Physalis floridana. First, we characterized the putative gene of a phytoene desaturase in P. floridana (PfPDS). Infecting the leaves of the Physalis seedlings with the PfPDS-TRV vector resulted in a bleached plant, including the developing leaves, floral organs, ICS, berry, and seed. These results indicated that a local VIGS treatment can efficiently induce a systemic mutated phenotype. qRT-PCR analyses revealed that the bleaching extent correlated to the mRNA reduction of the endogenous PfPDS. Detailed comparisons of multiple infiltration and growth protocols allowed us to determine the optimal methodologies for VIGS manipulation in Physalis. We subsequently utilized this optimized VIGS methodology to downregulate the expression of two MADS-box genes, MPF2 and MPF3, and compared the resulting effects with gene-downregulation mediated by RNA interference (RNAi) methods. The VIGS-mediated gene knockdown plants were found to resemble the mutated phenotypes of floral calyx, fruiting calyx and pollen maturation of the RNAi transgenic plants for both MPF2 and MPF3. Moreover, the two MADS-box genes were appeared to have a novel role in the pedicel development in P. floridana. The major advantage of VIGS-based gene knockdown lies in practical aspects of saving time and easy manipulation as compared to the RNAi. Despite the lack of heritability and mosaic mutation phenotypes observed in some organs, the TRV-mediated gene silencing system provides an alternative efficient way to infer gene function in various developmental processes in Physalis, thus facilitating understanding of the genetic basis of the evolution and development

  12. Molecular Cloning of a Cellulose Synthase Gene PtoCesA1 from Populus tomentosa and Its Genetic Transformation in Tobacco

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    A 3 125 bp cellulose synthase gene, PtoCesA1, which has a 98% identity to PtrCesA1 from Populus tremuloides,was cloned from cDNA prepared from secondary xylem of P. tomentosa. Four anti-expression vectors with different fragments of PtoCesA1, named as pBIPF, pBICC1, pBIPR and pBIBR, were constructed. Some traits of transformed tobacco of pBICC1, pBIPR and pBIBR differed from wild types, such as small leaves, "dwarf" phenotype and thinner xylem and fiber cell walls than wild plants consistent with a loss of cellulose. It indicated that the growth of transgenic tobacco was restrained by the expression of anti-PtoCesA1. Transgenic tobacco was obtained and the contents of cellulose and lignin were analyzed as well as the width and length of fiber cells, and xylem thickness for both transgenic and control plants. Transformed tobacco showed a different phenotype from control plants and it implied that PtoCesA1 was essential for the cellulose biosynthesis in poplar stems.

  13. Development of a ReaxFF potential for Pt-O systems describing the energetics and dynamics of Pt-oxide formation.

    Science.gov (United States)

    Fantauzzi, Donato; Bandlow, Jochen; Sabo, Lehel; Mueller, Jonathan E; van Duin, Adri C T; Jacob, Timo

    2014-11-14

    ReaxFF force field parameters describing Pt-Pt and Pt-O interactions have been developed and tested. The Pt-Pt parameters are shown to accurately account for the chemical nature, atomic structures and other materials properties of bulk platinum phases, low and high-index platinum surfaces and nanoclusters. The Pt-O parameters reliably describe bulk platinum oxides, as well as oxygen adsorption and oxide formation on Pt(111) terraces and the {111} and {100} steps connecting them. Good agreement between the force field and both density functional theory (DFT) calculations and experimental observations is demonstrated in the relative surface free energies of high symmetry Pt-O surface phases as a function of the oxygen chemical potential, making ReaxFF an ideal tool for more detailed investigations of more complex Pt-O surface structures. Validation for its application to studies of the kinetics and dynamics of surface oxide formation in the context of either molecular dynamics (MD) or Monte Carlo simulations are provided in part by a two-part investigation of oxygen diffusion on Pt(111), in which nudged elastic band (NEB) calculations and MD simulations are used to characterize diffusion processes and to determine the relevant diffusion coefficients and barriers. Finally, the power of the ReaxFF reactive force field approach in addressing surface structures well beyond the reach of routine DFT calculations is exhibited in a brief proof-of-concept study of oxygen adsorbate displacement within ordered overlayers.

  14. Reactions of Residents to Long-Term Sonic Boom Noise Environments

    Science.gov (United States)

    Fields, James M.

    1997-01-01

    A combined social survey and noise measurement program has been completed in 14 communities in two regions of the western United States that have been regularly exposed to sonic booms for many years. A total of 1,573 interviews were completed. Three aspects of the sonic booms are most disturbing: being startled, noticing rattles or vibrations, and being concerned about the possibility of damage from the booms. Sonic boom annoyance is greater than that in a conventional aircraft environment with the same continuous equivalent noise exposure. The reactions in the two study regions differ in severity.

  15. $N^{\\bf *}$ decays to $N\\omega$ from new data on $\\gamma p\\to \\omega p$

    CERN Document Server

    Denisenko, I; Crede, V; Eberhardt, H; Klempt, E; Nikonov, V A; Sarantsev, A V; Schmieden, H; Thoma, U; Wilson, A

    2016-01-01

    Data on the reaction $\\gamma p\\to \\omega p$ with $\\omega\\to\\pi^0\\gamma$, taken with unpolarized or polarized beams in combination with an unpolarized or polarized proton-target, were analyzed within the Bonn-Gatchina (BnGa) partial wave analysis. Differential cross sections, several spin density matrix elements, the beam asymmetry $\\Sigma$, the normalized helicity difference $E$, and the correlation $G$ between linear photon and longitudinal target polarization were included in a large data base on pion and photo-induced reactions. The data on $\\omega$ photoproduction are used to determine twelve $N^*\\to N\\omega$ branching ratios; most of these are determined for the first time.

  16. WaveSAX device: design optimization through scale modelling and a PTO strategical control system

    Science.gov (United States)

    Peviani, Maximo; Danelli, Andrea; Dadone, Gianluca; Dalmasso, Alberto

    2017-04-01

    simulating four wave conditions previously tested in the ocean tank at the ECN (Nantes, France). The results showed a satisfactory behaviour of the system and allowed to define the optimal velocity and torque conditions to maximize the PTO. REFERENCES 1. M. Peviani, 2015, 'WAVESAX device: conceptual design and perspectives', 8th European Seminar OWEMES 2015, Offshore Wind and other marine renewable Energies in Mediterranean and European Seas, Rome, Italy 2. B. Holmes, K. Nielsen, 2010, Guidelines for the Development & Testing of Wave Energy Systems, OES-IA Annex II Task 2.1, Report T02-2.1 3. G. Agate, A. Amicarelli, M. Peviani, 2014, 'Analisi fluidodinamica di un prototipo per la conversione di energia da moto ondoso: ottimizzazione della componente fissa e stime preliminari di potenza assorbita con la girante', RSE Ricerca di Sistema, Report 14001669 4. G. Agate, A. Amicarelli, A. Danelli, M. Peviani, 2015, 'Ottimizzazione del disegno di un dispositivo di generazione d'energia dal moto ondoso: simulazioni numeriche e studi in vasca di laboratorio idraulico, RSE Ricerca di Sistema, Report 15000671 5. A. Agate, A. Amicarelli, A. Danelli, M. Peviani, 2015. 'Optimization of the WaveSAX device: numerical modelling and ocean wave basin tests', VI International Conference on Computational Methods in Marine Engineering MARINE 2015, Rome, Italy 6. A. Danelli, M. Peviani, 2016. 'Performance evaluation of an innovative device to transform wave power into electric energy in ports and harbours". CORE 2nd International Conference on Offshore Renewable Energy; Glasgow, UK 7. M. Peviani, A. Danelli, G. Agate, F. Thiebaut, 2014, 'WAVETUBE RSE1, addressed to test an innovative device to transform wave power into electric energy in ports and harbours', Infrastructure post access report in the MARINET project framework 8. M. Peviani, A. Danelli, G. Agate, S. Bourdier, 2015, WAVESAX RSE2, addressed to test an innovative device to transform wave power into electric energy in ports and harbours

  17. Template-etching route to construct uniform rattle-type Fe3O4@SiO2 hollow microspheres as drug carrier.

    Science.gov (United States)

    Cheng, Lin; Liu, Yuanyuan; Zou, Bingfang; Yu, Yong; Ruan, Weimin; Wang, Yongqiang

    2017-06-01

    Template-etching strategy was put forward to synthesize rattle-type magnetic silica (Fe3O4@SiO2) hollow microspheres in a controlled way. During the experiment, monodisperse Fe2O3 microspheres were fabricated as physical template to generate uniform Fe2O3@SiO2 with controlled shell thicknesses through sol-gel method, and the subsequent Fe2O3 template etching process created variable space between Fe2O3 core and SiO2 shell, and the final calcination process transformed rattle-type Fe2O3@SiO2 hollow microspheres into corresponding Fe3O4@SiO2 product in hydrogen/nitrogen atmosphere. Compared with traditional physical template, here template-etching synthesis of rattle-type hollow microspheres saved the insertion of middle shells and their removal, which simplified the synthesis process with controllable core size and shell thickness. The rattle-type Fe3O4@SiO2 hollow microspheres as drug carrier show efficient doxorubicin (DOX) loading, and the release rate of DOX loaded the rattle-type Fe3O4@SiO2 hollow microspheres exhibit a surprising shell-thickness-dependent and a pH responsive drug release features. Additionally, MTT assays in HeLa cells demonstrated that the Fe3O4@SiO2 nanocarriers were non-toxic even at the concentration of 250µgmL(-1) for 48h. Thus, our results revealed that the Fe3O4@SiO2-DOX could play an important role in the development of intracellular delivery nanodevices for cancer therapy. Copyright © 2017. Published by Elsevier B.V.

  18. Paradigmas, eixos temáticos e tensões na PTO no Brasil Work and organizational psychology paradigms, thematic streams and tensions in Brazil

    Directory of Open Access Journals (Sweden)

    Pedro F. Bendassolli

    2010-12-01

    Full Text Available O panorama de abordagens da psicologia do trabalho e das organizações (PTO no Brasil mostra grande diversidade teórica e metodológica que reflete a presença de distintos paradigmas científicos na delimitação e organização desse campo. O objetivo deste artigo é analisar esses paradigmas e relacioná-los com três eixos temáticos da PTO no Brasil: o do comportamento, o da subjetividade e o clínico. Investiga-se os fundamentos epistemológicos e metodológicos, alguns trabalhos e autores de cada um desses eixos, discutindo sua contribuição para o campo da PTO no Brasil. O artigo desenvolve uma discussão sobre as tensões existentes entre esses eixos, derivadas da pressão de corresponderem, ao mesmo tempo, a critérios de rigor acadêmico e relevância organizacional. O artigo, por fim, mostra a diversificação do campo da PTO no Brasil e os desafios disso decorrentes.The great theoretical and methodological diversity of Work and Organizational Psychology (WOP approaches in Brazil reflects the presence of distinct scientific paradigms in the setting of boundaries and the organization of this field. The purpose of this paper is to analyze these paradigms and relate them with three WOP thematic streams in Brazil: the behavioral stream; the subjectivity stream; and the clinical stream. We investigate epistemological and methodological fundamentals, some studies and authors in each of these streams, discussing their contribution to the field of WOP in Brazil. The paper discusses the stresses that exist among these streams, which arise from the pressure of corresponding at once to academic rigor and organizational relevance criteria. Finally, the article shows the diversification of the field of WOP in Brazil and resulting challenges.

  19. Concerted Rattling in CsAg5 Te3 Leading to Ultralow Thermal Conductivity and High Thermoelectric Performance.

    Science.gov (United States)

    Lin, Hua; Tan, Gangjian; Shen, Jin-Ni; Hao, Shiqiang; Wu, Li-Ming; Calta, Nicholas; Malliakas, Christos; Wang, Si; Uher, Ctirad; Wolverton, Christopher; Kanatzidis, Mercouri G

    2016-09-12

    Thermoelectric (TE) materials convert heat energy directly into electricity, and introducing new materials with high conversion efficiency is a great challenge because of the rare combination of interdependent electrical and thermal transport properties required to be present in a single material. The TE efficiency is defined by the figure of merit ZT=(S(2) σ) T/κ, where S is the Seebeck coefficient, σ is the electrical conductivity, κ is the total thermal conductivity, and T is the absolute temperature. A new p-type thermoelectric material, CsAg5 Te3 , is presented that exhibits ultralow lattice thermal conductivity (ca. 0.18 Wm(-1)  K(-1) ) and a high figure of merit of about 1.5 at 727 K. The lattice thermal conductivity is the lowest among state-of-the-art thermoelectrics; it is attributed to a previously unrecognized phonon scattering mechanism that involves the concerted rattling of a group of Ag ions that strongly raises the Grüneisen parameters of the material.

  20. Produtividade de tomate 'Débora Pto' sob adubação organomineral via foliar e gotejamento Yield of tomato 'Débora Pto' under organic-mineral fertilization via foliar and drip irrigation

    Directory of Open Access Journals (Sweden)

    José Magno Q Luz

    2010-12-01

    Full Text Available O tomate ocupa o segundo lugar em importância econômica entre as hortaliças no Brasil. Para o incremento da produtividade, atualmente são utilizadas tecnologias como a aplicação de fertilizantes organominerais via foliar e fertirrigação, que visam estimular e melhorar o desenvolvimento do sistema radicular. O objetivo do trabalho foi avaliar a eficiência agronômica de produtos organominerais líquidos comerciais, aplicados via foliar e fertirrigação, na produtividade e qualidade de frutos de tomate híbrido Débora Pto. O experimento foi conduzido em Uberlândia, em delineamento inteiramente casualizado, constituído por três tratamentos e oito repetições. Os tratamentos foram: Testemunha; Tratamento 1: gotejamento de Aminoagro raiz 0,5 L ha-1 após transplantio e aplicação foliar de Aminoagro folha top 0,2 L ha-1, Aminoagro fosfito 0,2 L ha-1, Aminoagro energy 0,5 L ha-1 e Aminoagro fruto 0,2 L ha-1 e Aminoagro mol 1 L ha-1, iniciado no transplantio; Tratamento 2: aplicações foliares de Aminoagro raiz 0,5 L ha-1 após o transplantio; Aminoagro folha top 1 L ha-1; Aminoagro energy 2 L ha-1 juntamente com o Aminoagro folha top; Aminoagro mol 2 L ha-1 e 3 L ha-1, Aminoagro fosfito 1 L ha-1 e Aminoagro fruto 1 L ha-¹. Foi avaliada a produção de frutos de tomate de acordo com sua classificação por tamanho, sendo extra 2A, extra 1A e frutos descartados. Os resultados mostraram que a partir da terceira semana de colheita, os tratamentos 1 e 2 proporcionaram maior produção de tomate tipo extra 2A. O mesmo ocorreu para a produção total comercial. A produção total foi significativamente superior nos tratamentos 1 e 2 contendo os fertilizantes organominerais. As receitas líquidas obtidas nesses tratamentos foram superiores à receita obtida na testemunha.The tomato ranks second in economic importance among the vegetables in Brazil. To increase the productivity, technologies are currently used as the foliar application of the

  1. FITC Doped Rattle-Type Silica Colloidal Particle-Based Ratiometric Fluorescent Sensor for Biosensing and Imaging of Superoxide Anion.

    Science.gov (United States)

    Zhou, Ying; Ding, Jie; Liang, Tingxizi; Abdel-Halim, E S; Jiang, Liping; Zhu, Jun-Jie

    2016-03-01

    Fluorescent nanosensors have been widely applied in recognition and imaging of bioactive small molecules; however, the complicated surface modification process and background interference limit their applications in practical biological samples. Here, a simple, universal method was developed for ratiometric fluorescent determination of general small molecules. Taking superoxide anion (O2(•-)) as an example, the designed sensor was composed of three main moieties: probe carrier, rattle-type silica colloidal particles (mSiO2@hmSiO2 NPs); reference fluorophore doped into the core of NPs, fluorescein isothiocyanate (FITC); fluorescent probe for superoxide anion, hydroethidine (HE). In the absence of O2(•-), the sensor just emitted green fluorescence of FITC at 518 nm. When released HE was oxidized by O2(•-), the oxidation product exhibited red fluorescence at 570 nm and the intensity was linearly associated with the concentration of O2(•-), while that of reference element remained constant. Accordingly, ratiometric determination of O2(•-) was sensitively and selectively achieved with a linear range of 0.2-20 μM, and the detection limit was calculated as low as 80 nM. Besides, the technique was also successfully applied for dual-emission imaging of O2(•-) in live cells and realized visual recognition with obvious fluorescence color change in normal conditions or under oxidative stress. As long as appropriate reference dyes and sensing probes are selected, ratiometric biosensing and imaging of bioactive small molecules would be achieved. Therefore, the design could provide a simple, accurate, universal platform for biological applications.

  2. Assessing the tobacco-rattle-virus-based vectors system as an efficient gene silencing technique in Datura stramonium (Solanaceae).

    Science.gov (United States)

    Eftekhariyan Ghamsari, Mohammad Reza; Karimi, Farah; Mousavi Gargari, Seyed Latif; Hosseini Tafreshi, Seyed Ali; Salami, Seyed Alireza

    2014-12-01

    Datura stramonium is a well-known medicinal plant, which is important for its alkaloids. There are intrinsic limitations for the natural production of alkaloids in plants; metabolic engineering methods can be effectively used to conquer these limitations. In order for this the genes involved in corresponding pathways need to be studied. Virus-Induced Gene Silencing is known as a functional genomics technique to knock-down expression of endogenous genes. In this study, we silenced phytoene desaturase as a marker gene in D. stramonium in a heterologous and homologous manner by tobacco-rattle-virus-based VIGS vectors. Recombinant TRV vector containing pds gene from D. stramonium (pTRV2-Dspds) was constructed and injected into seedlings. The plants injected with pTRV2-Dspds showed photobleaching 2 weeks after infiltration. Spectrophotometric analysis demonstrated that the amount of chlorophylls and carotenoids in leaves of the bleached plants decreased considerably compared to that of the control plants. Semi-Quantitative RT-PCR results also confirmed that the expression of pds gene in the silenced plants was significantly reduced in comparison with the control plants. The results showed that the viral vector was able to influence the levels of total alkaloid content in D. stramonium. Our results illustrated that TRV-based VIGS vectors are able to induce effective and reliable functional gene silencing in D. stramonium as an alternative tool for studying the genes of interest in this plant, such as the targeted genes in tropane alkaloid biosynthetic pathway. The present work is the first report of establishing VIGS as an efficient method for transient silencing of any gene of interest in D. stramonium.

  3. Noise Measurement and Frequency Analysis of Commercially Available Noisy Toys

    Directory of Open Access Journals (Sweden)

    Shohreh Jalaie

    2005-06-01

    Full Text Available Objective: Noise measurement and frequency analysis of commercially available noisy toys were the main purposes of the study. Materials and Methods: 181 noisy toys commonly found in toy stores in different zones of Tehran were selected and categorized into 10 groups. Noise measurement were done at 2, 25, and 50 cm from toys in dBA. The noisiest toy of each group was frequency analyzed in octave bands. Results: The highest and the lowest intensity levels belonged to the gun (mean=112 dBA and range of 100-127 dBA and to the rattle-box (mean=84 dBA and range of 74-95 dBA, respectively. Noise intensity levels significantly decreased with increasing distance except for two toys. Noise frequency analysis indicated energy in effective hearing frequencies. Most of the toys energies were in the middle and high frequency region. Conclusion: As intensity level of the toys is considerable, mostly more than 90 dBA, and also their energy exist in the middle and high frequency region, toys should be considered as a cause of the hearing impairment.

  4. On/off multi-poppet valve for switching manifold in discrete fluid power force system PTO in wave energy converters

    DEFF Research Database (Denmark)

    Hansen, Anders Hedegaard; Pedersen, Henrik C.; Andersen, Torben Ole

    2014-01-01

    Fluid power systems are the leading technology for power take off systems in ocean wave energy converters. However, fluid power systems often suffer from poor efficiency, especially in part loads. This degrades the PTO system efficiency and therefore lowers the energy production. To overcome...... less than 10 ms. The pilot stage is directly actuated and utilises internal valve pressure as supply and an external tank connection as drain. The current paper presents the multi-disciplinary design process leading to the final valve design. This includes the geometric design of the main stage......, the choice of pilot valve, structural mechanical issues and modelling and simulation of various valve configurations. Hence, a mechatronic design process is utilised to choose the best valve configuration....

  5. Behaviors of the percentage depth dose curves along the beam axis of a phantom filled with different clinical PTO objects, a Monte Carlo Geant4 study

    Science.gov (United States)

    EL Bakkali, Jaafar; EL Bardouni, Tarek; Safavi, Seyedmostafa; Mohammed, Maged; Saeed, Mroan

    2016-08-01

    The aim of this work is to assess the capabilities of Monte Carlo Geant4 code to reproduce the real percentage depth dose (PDD) curves generated in phantoms which mimic three important clinical treatment situations that include lung slab, bone slab, bone-lung slab geometries. It is hoped that this work will lead us to a better understanding of dose distributions in an inhomogeneous medium, and to identify any limitations of dose calculation algorithm implemented in the Geant4 code. For this purpose, the PDD dosimetric functions associated to the three clinical situations described above, were compared to one produced in a homogeneous water phantom. Our results show, firstly, that the Geant4 simulation shows potential mistakes on the shape of the calculated PDD curve of the first physical test object (PTO), and it is obviously not able to successfully predict dose values in regions near to the boundaries between two different materials. This is, surely due to the electron transport algorithm and it is well-known as the artifacts at interface phenomenon. To deal with this issue, we have added and optimized the StepMax parameter to the dose calculation program; consequently the artifacts due to the electron transport were quasi disappeared. However, the Geant4 simulation becomes painfully slow when we attempt to completely resolve the electron artifact problems by considering a smaller value of an electron StepMax parameter. After electron transport optimization, our results demonstrate the medium-level capabilities of the Geant4 code to modeling dose distribution in clinical PTO objects.

  6. Molecular dynamics evidence for alkali-metal rattling in the β-pyrochlores, AOs2O6 (A = K, Rb, Cs).

    Science.gov (United States)

    Shoko, E; Peterson, V K; Kearley, G J

    2013-11-27

    We have used ab initio molecular dynamics simulations validated against inelastic neutron scattering data to study alkali-metal dynamics in the β-pyrochlore osmates AOs2O6 (A=K, Rb, Cs) at 300 K to gain insight into the microscopic nature of rattling dynamics in these materials. Our results provide new evidence at the microscopic level for rattling dynamics: (1) the elemental magnitude spectra calculated from the MD show a striking dominance by the alkali metals at low energies indicating weak coupling to the cage, (2) the atomic root-mean-square displacements for the alkali metals are significantly larger than for the other atoms, e.g., 25% and 150% larger than O and Os, respectively, in KOs2O6, and (3) motions of the alkali metals are weakly correlated to the dynamics in their immediate environment, e.g. K in KOs2O6 is 6 times less sensitive to its local environment than Os, indicating weak bonding of the K. There is broadening of the elemental spectra of the alkali metals from Cs to K corresponding to a similar broadening of the local potential around these atoms as determined from potential of mean-force calculations. This feature of the spectra is partly explained by the well-known increase in the relative cage volume with decreasing atomic size of the alkali metal. We find that for the smallest rattler in this series (K) the larger relative cage volume allows this atom freedom to explore a large space inside the cage leading to vibration at a broader range of frequencies, hence a broader spectrum. Thus, since K is considered the best rattler in this series, these findings suggest that a significant feature of a good rattler is the ability to vibrate at several different but closely spaced frequencies.

  7. Noise Pollution

    Science.gov (United States)

    ... Search Clean Air Act Overview Share Facebook Twitter Google+ Pinterest Contact Us Clean Air Act Title IV - ... noises in the community (from your neighbor, boom cars, lawn equipment, etc.) and from commercial businesses (factory, ...

  8. Klasik Türk Şiirinde Ceres (Çan/Çıngırak Ceres (Bell/Rattle in the Classical Turkish Poem

    Directory of Open Access Journals (Sweden)

    Bahir SELÇUK

    2012-09-01

    Full Text Available Ceres which is originally an Arabic word is used as bell, rattle in Turkish; as derâ in Persian. Having a long past, bell and rattle had different areas of use inancient life system. Ceres became a tool providing the communicationbetween caravan and the person in front of the caravan; performed thefunctions of preparation, setoff, holding the group together especiallyduring the times when the caravan trade was widespread. Besides tofollow fowlers, they were worn rattles to their feet.Indicators of bell and rattle attracted authors mostly with areas ofuse mentioned above in classical poetry which includes elements aboutdaily life because of various reasons. While the word ceres was used toexpress church bell time to time in poetry, mostly camel bell whichbecame the symbol of caravan trade was meant.Thanks to various features such as being hollow, being in theupside-down position, being so delicate, being involuntary, sounding allthe time, being heard far away, being put grass in it to block its soundand with its shape ceres provided the inspiration for authors. Besidestheme of passage and travel stands out in couplets about ceres.Expressing different situations inside them, in these travels lamentationwhich was caused because of troubles during the passage wasexpressed with the indicator of ceres.Authors managed to make rich and colourful images from thepoint of these features. In this work the couplets in which the wordceres (rattle, bell etc. takes place have been detected by searchingdivans; the reflection of ceres to literary text and imaginary elementsformed around ceres have been emphasized Arapça bir kelime olan ceres, Türkçede çan, çıngırak; Farsçada derâ şeklinde kullanılır. Geçmişi çok eski dönemlere uzanan kadar çan ve çıngırak, eski hayat sisteminde farklı kullanım alanları bulmuştur. Özellikle kervancılığın yaygın olduğu dönemlerde çan, kervanın başındaki kişi ile kervan ve kafile aras

  9. Muusikamaailm : Hans Werner Henze sünnipäevaks. "Nibelungide sõrmus" ka Dresdenis. Simon Rattle juhatas Beethovenit. Uued teosed Elliott Carterilt. Echo Klassik 2001 / Priit Kuusk

    Index Scriptorium Estoniae

    Kuusk, Priit, 1938-

    2001-01-01

    Hans Werner Henze 75 sünnipäevapidustustest Saksamaal. R. Wagneri "Nibelungide sõrmus" lavastus Dresdenis. Berliini Filharmoonikute peadirigent Simon Rattle toob Berliini pidunädalate lõppmänguna Berliini Filharmooniasse mahuka Beethoveni tsükli. Detsembris 93 aastaseks saav USA helilooja Elliott Carter kirjutab ikka uusi tellimusteoseid ning tuleb ka ise esiettekandele. Deutsche Phono-Akademie andis Baden-Badenis kätte oma mainekad aasta-auhinnad Echo Klassik

  10. Muusikamaailm : Hans Werner Henze sünnipäevaks. "Nibelungide sõrmus" ka Dresdenis. Simon Rattle juhatas Beethovenit. Uued teosed Elliott Carterilt. Echo Klassik 2001 / Priit Kuusk

    Index Scriptorium Estoniae

    Kuusk, Priit, 1938-

    2001-01-01

    Hans Werner Henze 75 sünnipäevapidustustest Saksamaal. R. Wagneri "Nibelungide sõrmus" lavastus Dresdenis. Berliini Filharmoonikute peadirigent Simon Rattle toob Berliini pidunädalate lõppmänguna Berliini Filharmooniasse mahuka Beethoveni tsükli. Detsembris 93 aastaseks saav USA helilooja Elliott Carter kirjutab ikka uusi tellimusteoseid ning tuleb ka ise esiettekandele. Deutsche Phono-Akademie andis Baden-Badenis kätte oma mainekad aasta-auhinnad Echo Klassik

  11. Fracture analysis and improvement of PTO shaft on marine gearbox for an offshore supply vessel%某近海供应船齿轮箱PTO轴断裂分析及改进

    Institute of Scientific and Technical Information of China (English)

    周晓梅; 黄将兴; 戴宏长; 沈先

    2013-01-01

    Aiming that PTO shafts fracture occurring during operation of a marine gearbox on an offshore supply vessel,in the case of the high flexible coupling is damaged because of the bad alignment of the high flexible coupling, through making mechanical model together with measuring technique and material metallographic analysis, all possible causes resulting to the fracture were found out. On the basis of mechanics analysis of the PTO shaft,stress condition of the sink groove of the PTO shaft were studied mainly and the two dimensional stress state of the weakest point was analyzed, when the high flexible coupling became cantilever load. Then, several precautions of improving strength of the PTO shaft were raised. The research result proves that, the strength of the PTO shaft is affected quite by installation accuracy of the high flexible coupling, and the improvement actions presented can eliminate the broken shaft event from happening again, ensure the normal operation of equipment.%针对某近海供应船齿轮箱在运行过程中发生PTO轴断裂这一问题,通过建立力学模型并结合测量技术和金相分析技术,对由于校中不好而引起高弹性联轴器损坏的情况下的PTO轴进行了分析,找出了各种可能造成PTO轴损坏的原因;在对PTO轴进行受力分析的基础上,着重研究了当高弹性联轴器成为悬臂负载时PTO轴的受力状况,分析了最薄弱处的二向应力状态,提出了提高PTO轴强度的几种措施.研究结果表明,针对高弹性联轴器的安装精度对船用齿轮箱PTO轴的强度影响,所提出的改进措施能够消除断轴事件的再次发生,保证设备的正常运行.

  12. Low noise road surfaces

    OpenAIRE

    Bolčina, Matjaž

    2014-01-01

    Noise is everywhere. Noise is a sound that makes people stressful and irritate. It often couses sleep disorders and also health problems like different cardiovascular disorders, hearing loss…In most cases traffic noise is the most disturbing. There are different ways to prevent people from traffic noise like building noise barriers and insulation of facades. However noise barriers and insulation of facades do not prevent noise formation, but are lowering existing noise. Another disadvantage i...

  13. Low frequency noise case study : identification and mitigation of a severe infrasonic tone from a mine shaft ventilation fan

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, R.D. [HGC Engineering, Mississauga, ON (Canada)

    2007-07-01

    This paper presented a solution for a severe low frequency infrasound problem experienced at a home near a large mine shaft ventilation fan in Dallas, West Virginia. Strong low frequency acoustic pulsations were detected as far as 200 metres from the fan. HGC Engineering was retained by the coal mine company to investigate the source of the problem and to find solutions. Controlling low frequency sound is a challenge because the wavelengths of sound are long at low frequencies. The relatively high level of acoustic energy of a low frequency sound or infrasound that is loud enough to be heard also presents a problem for noise control. In order to be effective, low frequency noise control measures must usually be large, bulky and expensive. In this study, HGC Engineering readily identified acoustic pulsations in the order of 75 dB at 15 Hz outside the residences. At 15 Hz, the infrasound was not audible at the residence, but was causing rattling of lightweight furnishings inside the home. The measured sound pressure level at 15 Hz was approximately 10 dB greater than the onset of risk for rattling and perceptible vibration. The vibration was also perceptible on the walls and windows of the dwellings. The vibration of the dwelling structure had a high measured coherence with the air-borne pulsations at 15 Hz, suggesting that the vibration was induced by the air-borne infrasonic pulsations. HGC Engineering determined that 15 Hz corresponded to the rotational speed of the fan. A reduction of 15 dB at 15 Hz was targeted, in order to reduce the perceptibility and risk of rattling at the residence. A tuned acoustic plenum was considered to be a viable method to silence the fan. In order to investigate the effectiveness of this approach, HGC Engineering conducted a preliminary analytical design and parametric study of an acoustic plenum tuned to 15 Hz. An analytical model was developed to determine the acoustic behaviour of the plenum. In addition, a numerical boundary

  14. Inhibitory noise

    Directory of Open Access Journals (Sweden)

    Alain Destexhe

    2010-03-01

    Full Text Available Cortical neurons in vivo may operate in high-conductance states, in which the major part of the neuron's input conductance is due to synaptic activity, sometimes several-fold larger than the resting conductance. We examine here the contribution of inhibition in such high-conductance states. At the level of the absolute conductance values, several studies have shown that cortical neurons in vivo are characterized by strong inhibitory conductances. However, conductances are balanced and spiking activity is mostly determined by fluctuations, but not much is known about excitatory and inhibitory contributions to these fluctuations. Models and dynamic-clamp experiments show that, during high-conductance states, spikes are mainly determined by fluctuations of inhibition, or by inhibitory noise. This stands in contrast to low-conductance states, in which excitatory conductances determine spiking activity. To determine these contributions from experimental data, maximum likelihood methods can be designed and applied to intracellular recordings in vivo. Such methods indicate that action potentials are indeed mostly correlated with inhibitory fluctuations in awake animals. These results argue for a determinant role for inhibitory fluctuations in evoking spikes, and do not support feed-forward modes of processing, for which opposite patterns are predicted.

  15. Occupational noise management

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-06-15

    Occupational noise is a frequently encountered on-the-job health hazard. This guide presented the responsibilities and regulatory requirements related to business activities where noise above 80 decibels is present. The guide provided a definition of noise and discussed noise hazards, types of noise, and on-the-job noise exposure. A risk assessment to noise in the work environment was also discussed. A guide to a hearing conservation program was also included. The main purpose of a hearing conservation program is the prevention of noise induced hearing loss for employees exposed to occupational noise. The components of such a program were outlined, with particular reference to noise monitoring; noise exposure control; worker education and training; hearing (audiometric) testing; and annual program review and record keeping. It was concluded that in terms of record keeping, it can be very helpful to file noise exposure assessments, particularly personal exposure measurements, with hearing test records to facilitate for future reference. refs., appendices.

  16. Noise and Hearing Protection

    Science.gov (United States)

    ... ENTCareers Marketplace Find an ENT Doctor Near You Noise and Hearing Protection Noise and Hearing Protection Patient ... it is. How can I tell if a noise is dangerous? People differ in their sensitivity to ...

  17. Can Noise Kill People?

    Institute of Scientific and Technical Information of China (English)

    刘玲娣

    2007-01-01

    Someone is singing next door,but you feel unhappy because her singing is just making a noise.We know that too much noise makes people feel terrible. Scientists are still trying to find out more about noise,but already it is known that a noise of over 85 decibels can make some people tired and anxious.

  18. Active Noise Control for Dishwasher noise

    Science.gov (United States)

    Lee, Nokhaeng; Park, Youngjin

    2016-09-01

    The dishwasher is a useful home appliance and continually used for automatically washing dishes. It's commonly placed in the kitchen with built-in style for practicality and better use of space. In this environment, people are easily exposed to dishwasher noise, so it is an important issue for the consumers, especially for the people living in open and narrow space. Recently, the sound power levels of the noise are about 40 - 50 dBA. It could be achieved by removal of noise sources and passive means of insulating acoustical path. For more reduction, such a quiet mode with the lower speed of cycle has been introduced, but this deteriorates the washing capacity. Under this background, we propose active noise control for dishwasher noise. It is observed that the noise is propagating mainly from the lower part of the front side. Control speakers are placed in the part for the collocation. Observation part of estimating sound field distribution and control part of generating the anti-noise are designed for active noise control. Simulation result shows proposed active noise control scheme could have a potential application for dishwasher noise reduction.

  19. Mechanics of underwater noise

    CERN Document Server

    Ross, Donald

    1976-01-01

    Mechanics of Underwater Noise elucidates the basic mechanisms by which noise is generated, transmitted by structures and radiated into the sea. Organized into 10 chapters, this book begins with a description of noise, decibels and levels, significance of spectra, and passive sonar equation. Subsequent chapters discuss sound waves in liquids; acoustic radiation fundamentals; wind-generated ocean ambient noise; vibration isolation and structural damping; and radiation by plate flexural vibrations. Other chapters address cavitation, propeller cavitation noise, radiation by fluctuating-force (dipo

  20. Solar noise storms

    CERN Document Server

    Elgaroy, E O

    2013-01-01

    Solar Noise Storms examines the properties and features of solar noise storm phenomenon. The book also presents some theories that can be used to gain a better understanding of the phenomenon. The coverage of the text includes topics that cover the features and behavior of noise storms, such as the observable features of noise storms; the relationship between noise storms and the observable features on the sun; and ordered behavior of storm bursts in the time-frequency plane. The book also covers the spectrum, polarization, and directivity of noise storms. The text will be of great use to astr

  1. Infant Cries Rattle Adult Cognition.

    Directory of Open Access Journals (Sweden)

    Joanna Dudek

    Full Text Available The attention-grabbing quality of the infant cry is well recognized, but how the emotional valence of infant vocal signals affects adult cognition and cortical activity has heretofore been unknown. We examined the effects of two contrasting infant vocalizations (cries vs. laughs on adult performance on a Stroop task using a cross-modal distraction paradigm in which infant distractors were vocal and targets were visual. Infant vocalizations were presented before (Experiment 1 or during each Stroop trial (Experiment 2. To evaluate the influence of infant vocalizations on cognitive control, neural responses to the Stroop task were obtained by measuring electroencephalography (EEG and event-related potentials (ERPs in Experiment 1. Based on the previously demonstrated existence of negative arousal bias, we hypothesized that cry vocalizations would be more distracting and invoke greater conflict processing than laugh vocalizations. Similarly, we expected participants to have greater difficulty shifting attention from the vocal distractors to the target task after hearing cries vs. after hearing laughs. Behavioral results from both experiments showed a cry interference effect, in which task performance was slower with cry than with laugh distractors. Electrophysiology data further revealed that cries more than laughs reduced attention to the task (smaller P200 and increased conflict processing (larger N450, albeit differently for incongruent and congruent trials. Results from a correlation analysis showed that the amplitudes of P200 and N450 were inversely related, suggesting a reciprocal relationship between attention and conflict processing. The findings suggest that cognitive control processes contribute to an attention bias to infant signals, which is modulated in part by the valence of the infant vocalization and the demands of the cognitive task. The findings thus support the notion that infant cries elicit a negative arousal bias that is distracting; they also identify, for the first time, the neural dynamics underlying the unique influence that infant cries and laughs have on cognitive control.

  2. Helicopter Noise And Noise Abatement Procedures

    Directory of Open Access Journals (Sweden)

    Borivoj Galović

    2004-03-01

    Full Text Available The helicopter generated noise at and around the airports islower than the noise generated by aeroplanes, since their numberof operations, i. e. the number of takeoffs and landings ismuch lower than the takeoffs and landings of the aeroplanes.Out of some hundred operations a day, helicopters participatewith approximately 15%, but the very impact of noise is by nomeans negligible, since the number of helicopter flights aboveurban areas is constantly increasing.This paper attempts to analyse this phenomenon and thetype of helicopter generated noise, its negative impacts, to explainthe flight procedures and the operative procedures duringtakeoff, landing and overflight of helicopters in operations inthe vicinity and outside airports, as well as the methods of measuringand determining the limit of noise [eve~ and the resultingproblems.

  3. Noise Gating Solar Images

    Science.gov (United States)

    DeForest, Craig; Seaton, Daniel B.; Darnell, John A.

    2017-08-01

    I present and demonstrate a new, general purpose post-processing technique, "3D noise gating", that can reduce image noise by an order of magnitude or more without effective loss of spatial or temporal resolution in typical solar applications.Nearly all scientific images are, ultimately, limited by noise. Noise can be direct Poisson "shot noise" from photon counting effects, or introduced by other means such as detector read noise. Noise is typically represented as a random variable (perhaps with location- or image-dependent characteristics) that is sampled once per pixel or once per resolution element of an image sequence. Noise limits many aspects of image analysis, including photometry, spatiotemporal resolution, feature identification, morphology extraction, and background modeling and separation.Identifying and separating noise from image signal is difficult. The common practice of blurring in space and/or time works because most image "signal" is concentrated in the low Fourier components of an image, while noise is evenly distributed. Blurring in space and/or time attenuates the high spatial and temporal frequencies, reducing noise at the expense of also attenuating image detail. Noise-gating exploits the same property -- "coherence" -- that we use to identify features in images, to separate image features from noise.Processing image sequences through 3-D noise gating results in spectacular (more than 10x) improvements in signal-to-noise ratio, while not blurring bright, resolved features in either space or time. This improves most types of image analysis, including feature identification, time sequence extraction, absolute and relative photometry (including differential emission measure analysis), feature tracking, computer vision, correlation tracking, background modeling, cross-scale analysis, visual display/presentation, and image compression.I will introduce noise gating, describe the method, and show examples from several instruments (including SDO

  4. Noise-Measuring Method

    DEFF Research Database (Denmark)

    Diamond, J. M.

    1965-01-01

    A noise-measuring method based on the use of a calibrated noise generator and an output meter with a special scale is described. The method eliminates the effect of noise contributions occurring in the circuits following the device under test....

  5. Introductory guide to noise

    CSIR Research Space (South Africa)

    Ferreira, T.M

    1973-01-01

    Full Text Available The difference between sound and noise varies from one human being to another. Noise, then, is simply unwanted sound and to understand how it can be combatted we must know more about its nature. A guide of acceptable levels of noise are investigated....

  6. Adaptive Noise Reduction System

    Directory of Open Access Journals (Sweden)

    Ivana Ropuš

    2013-01-01

    Full Text Available Noise is an all-present environment pollutant, considered to be one of the greatest contemporary pollutants. World-wide, co-ordinated actions are conducted in order to develop systems which minimise the noise influence onto society.In this article we argue that novel approach to suppression of influence of noise is useful. Furthermore, we argue that the efficient approach is formulation of the efficient, broadly applicable, ubiquituous, adaptive noise-protection system. The approach combines the natural noise-protection form based on plants with the artificially formed coatings.Elements of the system are discussed, its formation and maintenance analysed and perspectives conjectured.

  7. Low-noise amplifier

    Directory of Open Access Journals (Sweden)

    V. B. Gulkov

    2012-11-01

    Full Text Available The mixture of signal and noise processing device is considered in this article. It contains two channels: the main channel (MC contains the mixture of signal and noise, and compensation channel (CC that extracts just a noise from the mixture. The feature of the processing circuit is that the mixture samples are formed by short impulses at the moments of passing signal through zero. Further antiphase noise is set in the channels, adder by which the noise is removed from mixture is set on the cannels output. Study of the described device was carried out for simulated AM signal and white Gaussian noise in simulation environment Matlab. The results are shown, that device reduces noise by 16 dB of power.

  8. Noise from wind turbines

    Energy Technology Data Exchange (ETDEWEB)

    Fegeant, Olivier [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Building Sciences

    2002-02-01

    A rapid growth of installed wind power capacity is expected in the next few years. However, the siting of wind turbines on a large scale raises concerns about their environmental impact, notably with respect to noise. To this end, variable speed wind turbines offer a promising solution for applications in densely populated areas like the European countries, as this design would enable an efficient utilisation of the masking effect due to ambient noise. In rural and recreational areas where wind turbines are sited, the ambient noise originates from the action of wind on the vegetation and about the listener's ear (pseudo-noise). It shows a wind speed dependence similar to that of the noise from a variable speed wind turbine and can therefore mask the latter for a wide range of conditions. However, a problem inherent to the design of these machines is their proclivity to pure tone generation, because of the enhanced difficulty of avoiding structural resonances in the mechanical parts. Pure tones are deemed highly annoying and are severely regulated by most noise policies. In relation to this problem, the vibration transmission of structure-borne sound to the tower of the turbine is investigated, in particular when the tower is stiffened at its upper end. Furthermore, since noise annoyance due to wind turbine is mostly a masking issue, the wind-related sources of ambient noise are studied and their masking potentials assessed. With this aim, prediction models for wind-induced vegetation noise and pseudo-noise have been developed. Finally, closely related to the effect of masking, is the difficulty, regularly encountered by local authorities and wind farm developers, to measure noise immission from wind turbines. A new measurement technique has thus been developed in the course of this work. Through improving the signal-to-noise ratio between wind turbine noise and ambient noise, the new technique yields more accurate measurement results.

  9. assessment of noise pollutio noise pollutio noise pollution from ...

    African Journals Online (AJOL)

    eobe

    sawmill noise on the metropolis was developed. the metropolis was ... INTRODUCTION. INTRODUCTION ... auditory fatigue and hearing loss, and indirect n auditory effects such as speech interfere annoyance .... acoustic environment for workers [29]. In particular, ..... and corn mills”, African Journal of Health Science,. Vol.

  10. Adaptive noise cancellation

    CERN Document Server

    Akram, N

    1999-01-01

    In this report we describe the concept of adaptive noise canceling, an alternative method of estimating signals corrupted by additive noise of interference. The method uses 'primary' input containing the corrupted signal and a 'reference' input containing noise correlated in some unknown way with the primary noise, the reference input is adaptively filtered and subtracted from the primary input to obtain the signal estimate. Adaptive filtering before subtraction allows the treatment of inputs that are deterministic or stochastic, stationary or time variable. When the reference input is free of signal and certain other conditions are met then noise in the primary input can be essentially eliminated without signal distortion. It is further shown that the adaptive filter also acts as notch filter. Simulated results illustrate the usefulness of the adaptive noise canceling technique.

  11. Acceptable noise level

    DEFF Research Database (Denmark)

    Olsen, Steen Østergaard; Nielsen, Lars Holme; Lantz, Johannes;

    2012-01-01

    The acceptable noise level (ANL) is used to quantify the amount of background noise that subjects can accept while listening to speech, and is suggested for prediction of individual hearing-aid use. The aim of this study was to assess the repeatability of the ANL measured in normal-hearing subjec...... using running Danish and non-semantic speech materials as stimuli and modulated speech-spectrum and multi-talker babble noises as competing stimuli....

  12. Noise at the Interface

    DEFF Research Database (Denmark)

    Prior, Andrew

    2011-01-01

    The notion of noise occupies a contested territory, in which it is framed as pollution and detritus even as it makes its opposite a possibility - noise is always defined in opposition to something else, even if this ‘other’ is not quite clear. This paper explores noise in the context of ‘the inte...... interface’ asking what its affordances as an idea may contribute to our understanding of interface. I draw historically on information theory in particular to initiate this exploration....

  13. Landing gear noise attenuation

    Science.gov (United States)

    Moe, Jeffrey W. (Inventor); Whitmire, Julia (Inventor); Kwan, Hwa-Wan (Inventor); Abeysinghe, Amal (Inventor)

    2011-01-01

    A landing gear noise attenuator mitigates noise generated by airframe deployable landing gear. The noise attenuator can have a first position when the landing gear is in its deployed or down position, and a second position when the landing gear is in its up or stowed position. The noise attenuator may be an inflatable fairing that does not compromise limited space constraints associated with landing gear retraction and stowage. A truck fairing mounted under a truck beam can have a compliant edge to allow for non-destructive impingement of a deflected fire during certain conditions.

  14. Measurement of Target and Double-spin Asymmetries for the $\\vec e\\vec p\\to e\\pi^+ (n)$ Reaction in the Nucleon Resonance Region at Low $Q^2$

    CERN Document Server

    Zheng, X; Bosted, P; Deur, A; Drozdov, V; Fassi, L El; Kang, Hyekoo; Kovacs, K; Kuhn, S; Long, E; Phillips, S K; Ripani, M; Slifer, K; Smith, L C; Adikaram, D; Akbar, Z; Amaryan, M J; Pereira, S Anefalos; Asryan, G; Avakian, H; Badui, R A; Ball, J; Baltzell, N A; Battaglieri, M; Batourine, V; Bedlinskiy, I; Biselli, A S; Briscoe, W J; Bültmann, S; Burkert, V D; Carman, D S; Celentano, A; Chandavar, S; Charles, G; Chen, J -P; Chetry, T; Choi, Seonho; Ciullo, G; Clark, L; Colaneri, L; Cole, P L; Compton, N; Contalbrigo, M; Crede, V; D'Angelo, A; Dashyan, N; De Vita, R; De Sanctis, E; Djalali, C; Dodge, G E; Dupre, R; Egiyan, H; Alaoui, A El; Elouadrhiri, L; Eugenio, P; Fanchini, E; Fedotov, G; Fersch, R; Filippi, A; Fleming, J A; Gevorgyan, N; Ghandilyan, Y; Gilfoyle, G P; Giovanetti, K L; Girod, F X; Gleason, C; Golovach, E; Gothe, R W; Griffioen, K A; Guidal, M; Guler, N; Guo, L; Hanretty, C; Harrison, N; Hattawy, M; Hicks, K; Holtrop, M; Hughes, S M; Ilieva, Y; Ireland, D G; Ishkhanov, B S; Isupov, E L; Jenkins, D; Jiang, H; Jo, H S; Joosten, S; Keller, D; Khachatryan, G; Khandaker, M; Kim, A; Kim, W; Klein, F J; Kubarovsky, V; Lanza, L; Lenisa, P; Livingston, K; MacGregor, I J D; Markov, N; McKinnon, B; Mirazita, M; Mokeev, V; Movsisyan, A; Munevar, E; Camacho, C Munoz; Murdoch, G; Nadel-Turonski, P; Net, L A; Ni, A; Niccolai, S; Niculescu, G; Niculescu, I; Osipenko, M; Ostrovidov, A I; Paolone, M; Paremuzyan, R; Park, K; Pasyuk, E; Peng, P; Pisano, S; Pogorelko, O; Price, J W; Puckett, A J R; Raue, B A; Rizzo, A; Rosner, G; Rossi, P; Roy, P; Sabatié, F; Salgado, C; Schumacher, R A; Sharabian, Y G; Skorodumina, Iu; Smith, G D; Sokhan, D; Sparveris, N; Stankovic, I; Strakovsky, I I; Strauch, S; Taiuti, M; Tian, Ye; Ungaro, M; Voskanyan, H; Voutier, E; Walford, N K; Watts, D P; Wei, X; Weinstein, L B; Wood, M H; Zachariou, N; Zhang, J

    2016-01-01

    We report measurements of target- and double-spin asymmetries for the exclusive channel $\\vec e\\vec p\\to e\\pi^+ (n)$ in the nucleon resonance region at Jefferson Lab using the CEBAF Large Acceptance Spectrometer (CLAS). These asymmetries were extracted from data obtained using a longitudinally polarized NH$_3$ target and a longitudinally polarized electron beam with energies 1.1, 1.3, 2.0, 2.3 and 3.0 GeV. The new results are consistent with previous CLAS publications but are extended to a low $Q^2$ range from $0.0065$ to $0.35$ (GeV$/c$)$^2$. The $Q^2$ access was made possible by a custom-built Cherenkov detector that allowed the detection of electrons for scattering angles as low as $6^\\circ$. These results are compared with the unitary isobar models JANR and MAID, the partial-wave analysis prediction from SAID and the dynamic model DMT. In many kinematic regions our results, in particular results on the target asymmetry, help to constrain the polarization-dependent components of these models.

  15. Noise and Health: How does noise affect us?

    NARCIS (Netherlands)

    Miedema, H.M.E.

    2001-01-01

    Noise annoyance is a primary indication that noise is a problem, and by itself noise annoyance means that the quality of life is adversely affected. Results from noise annoyance research are presented that make possible a detailed evaluation of noise exposures with respect to the annoyance induced.

  16. Mediality is Noise

    DEFF Research Database (Denmark)

    Prior, Andrew

    This PhD is concerned with the use of noise as a material within media arts practice, especially in ‘post-digital’ contexts such as glitch electronica, glitch art and uses of old media. It examines the relationship between informational culture and noise, exploring the ways in which the structuring...

  17. Sounding Off about Noise

    Science.gov (United States)

    Crumpton, Michael A.

    2005-01-01

    Noise in a community college library can be part of the nature of the environment. It can also become a huge distraction for those who see the library as their sanctuary for quiet study and review of resources. This article describes the steps that should be taken by library staff in order to be proactive about noise and the library environment,…

  18. Effects of traffic noise

    Energy Technology Data Exchange (ETDEWEB)

    Gottlob, D.

    1986-02-01

    One of the main sources of noise is road traffic. In 1984 there were over 25 million cars, 1.2 million lorries, 1.3 million motor cycles and 1.6 million mopeds using our roads. Opinion polls showed that 21% of the population felt that they were affected by traffic noise as a nuisance factor. An outline of the effects of this noise on the affected population is given, illustrated by diagrams. Details about noise emissions (drive-past level) of the different types of vehicles in city traffic are stated and the effects of noise described. The author goes into the nuisance effect (noise is not a physical factor, but a psychosocial one), changes in behaviour (ways of speaking, reduction of stress on households in proportion to rising income and higher educational levels) and the consequences for health (the reaction of the body to noise is primarily a consequence of the psychosomatic organisation of ow bodies). In conclusion, the author deals with the subjective efficiency of noise protection measures. (HWJ).

  19. Speech communications in noise

    Science.gov (United States)

    1984-07-01

    The physical characteristics of speech, the methods of speech masking measurement, and the effects of noise on speech communication are investigated. Topics include the speech signal and intelligibility, the effects of noise on intelligibility, the articulation index, and various devices for evaluating speech systems.

  20. Noise in Coevolving Networks

    CERN Document Server

    Diakonova, Marina; Miguel, Maxi San

    2014-01-01

    Coupling dynamics of the states of the nodes of a network to the dynamics of the network topology leads to generic absorbing and fragmentation transitions. The coevolving voter model is a typical system that exhibits such transitions at some critical rewiring. We study the robustness of these transitions under two distinct ways of introducing noise. Noise affecting all the nodes destroys the absorbing-fragmentation transition, giving rise in finite-size systems to two regimes: bimodal magnetisation and dynamic fragmentation. Noise Targeting a fraction of nodes preserves the transitions but introduces shattered fragmentation with its characteristic fraction of isolated nodes and one or two giant components. Both the lack of absorbing state for homogenous noise and the shift in the absorbing transition to higher rewiring for targeted noise are supported by analytical approximations.

  1. Noise and Hearing Loss Prevention

    Science.gov (United States)

    ... visit this page: About CDC.gov . NOISE AND HEARING LOSS PREVENTION Recommend on Facebook Tweet Share Compartir Worker ... noise levels cannot be adequately reduced. Noise and Hearing Loss on the NIOSH Science Blog Read and comment ...

  2. FET noise studies

    Science.gov (United States)

    Pucel, R. A.

    1981-03-01

    The GaAs FET oscillator is an alternative device for voltage-controlled oscillator (VCO) applications because of its inherent wide-band electronic tunability, the variety of operating modes possible such as common source, common gate, etc., and the ease of circuit design. However, it has one major drawback, namely, its high near-carrier 1/f noise which makes it unsuitable for many applications, such as radar systems. This report describes the progress made during the report period in understanding the physical mechanisms responsible for this noise. During this period, an extensive experimental study was made of the 1/f noise properties of a variety of oscillators constructed of FET chips fabricated under controlled conditions. Using in-house grown epitaxial wafers, FET's were fabricated from both buffered and unbuffered active layers, with and without epitaxially grown contact layers, and with and without surface passivation. The experimental results show a good correlation between the trap-generated 1/f baseband noise and the near-carrier 1/f FM noise. The primary sources of the noise are presumed to be either deep traps within the depletion layer under the gate or surface states at the gate-semiconductor interface, probably the latter. An improvement of the order of 10 dB in the near carrier FM noise level is obtained when a buffer layer separates the active layer from the substrate. Optical experiments indicated an electron trap level approximately 0.41 eV below the conduction band. A noise model was devised to explain the modulation process for upconverting baseband 1/f noise to the carrier band by depletion layer modulation.

  3. Criteria for environmental noise assessment

    OpenAIRE

    Hadzi-Nikolova, Marija; Mirakovski, Dejan; Doneva, Nikolinka

    2015-01-01

    The noise assessment generally refers to the assessment of noise impact from a specific source, such as noise originating from certain industrial plants, road traffic, and this is not always an easy task. Practically in every surrounding, a number of different sources contribute to the ambiental noise at a certain point. Standardization of noise level includes recommendations for noise level prescribed by legislation, which are enabling stay in the environment without danger to human heal...

  4. Controlled Noise Seismology

    KAUST Repository

    Hanafy, Sherif M.

    2015-08-19

    We use controlled noise seismology (CNS) to generate surface waves, where we continuously record seismic data while generating artificial noise along the profile line. To generate the CNS data we drove a vehicle around the geophone line and continuously recorded the generated noise. The recorded data set is then correlated over different time windows and the correlograms are stacked together to generate the surface waves. The virtual shot gathers reveal surface waves with moveout velocities that closely approximate those from active source shot gathers.

  5. Vacuum and Co-cultivation Agroinfiltration of (Germinated) Seeds Results in Tobacco Rattle Virus (TRV) Mediated Whole-Plant Virus-Induced Gene Silencing (VIGS) in Wheat and Maize

    Science.gov (United States)

    Zhang, Ju; Yu, Deshui; Zhang, Yi; Liu, Kun; Xu, Kedong; Zhang, Fuli; Wang, Jian; Tan, Guangxuan; Nie, Xianhui; Ji, Qiaohua; Zhao, Lu; Li, Chengwei

    2017-01-01

    Tobacco rattle virus (TRV)-mediated virus-induced gene silencing (VIGS) has been frequently used in dicots. Here we show that it can also be used in monocots, by presenting a system involving use of a novel infiltration solution (containing acetosyringone, cysteine, and Tween 20) that enables whole-plant level VIGS of (germinated) seeds in wheat and maize. Using the established system, phytoene desaturase (PDS) genes were successfully silenced, resulting in typical photo-bleaching symptoms in the leaves of treated wheat and maize. In addition, three wheat homoeoalleles of MLO, a key gene repressing defense responses to powdery mildew in wheat, were simultaneously silenced in susceptible wheat with this system, resulting in it becoming resistant to powdery mildew. The system has the advantages generally associated with TRV-mediated VIGS systems (e.g., high-efficiency, mild virus infection symptoms, and effectiveness in different organs). However, it also has the following further advantages: (germinated) seed-stage agroinfiltration; greater rapidity and convenience; whole-plant level gene silencing; adequately stable transformation; and suitability for studying functions of genes involved in seed germination and early plant development stages.

  6. 某大功率柴油机结构振动辐射噪声源探究%Study on the radiated noise source from structure vibration of a large power diesel engine

    Institute of Scientific and Technical Information of China (English)

    张学龙; 付艳丽; 马永兵; 赵国刚

    2014-01-01

    Big noise and rattle was annoyed at idling work by vehicle users when a new type large power diesel engine which was researched and developed by a domestic company was assembled to vehicle. Vibration and noise tests were performed in test-room and on vehicle separately in order to locate the noise source. The results of tests show that the noise mainly stem from the gear-housing, high pressure oil pump, air compressor and valve cover. The rattle from the gear-housing was the knocks which were because of the over-big clearance between two gears when gears mesh. At last two ways of reducing noise were proposed, one is that shield were assembled around the gear-housing, high pressure oil pump and air compressor, the other is to redesign and optimize the stepped-gear and the bolts of the valve cover to reduce the knocks of gears and the couple vibration of the valve cover and reduce the noise.%某公司研发的大功率柴油机装车后,用户反映怠速时发动机后端噪声大,并伴有“格拉拉”的异响。为确定发动机的噪声源,本文分别在台架和整车上对发动机做了振动噪声试验,试验结果显示发动机的噪声主要来自齿轮室、高压油泵和空压机以及缸盖罩壳,发动机“格拉拉”的异响是齿轮室的齿轮撞击声,造成齿轮撞击的主要原因是齿轮啮合间隙过大。对此本文提出了两种降噪方案:第一在齿轮室、高压油泵和空压机等处加装遮蔽罩;第二改进齿轮和缸盖罩壳设计,减小齿轮啮合间隙和缸盖罩壳耦合振动,降低噪声。

  7. Acoustics Noise Test Cell

    Data.gov (United States)

    Federal Laboratory Consortium — The Acoustic Noise Test Cell at the NASA/Caltech Jet Propulsion Laboratory (JPL) is located adjacent to the large vibration system; both are located in a class 10K...

  8. Noise upon the Sinusoids

    DEFF Research Database (Denmark)

    Jensen, Karl Kristoffer

    2005-01-01

    Sinusoids are used for making harmonic and other sounds. In order to having life in the sounds and adding a wide variety of noises, irregularities are inserted in the frequency and amplitudes. A simple and intuitive noise model is presented, consisting of a low-pass filtered noise, and having...... control for strength and bandwidth. The noise is added on the frequency and amplitudes of the sinusoids, and the resulting irregularity’s (jitter and shimmer) bandwidth is derived. This, together with an overview of investigation methods of the jitter and shimmer results in an analysis of the necessary...... samplerate of the shimmer and jitter. A harmonic model introduces individual and common irregularity, and adds a correlation control. The model has been implemented in max/msp and used in contemporary music compositions....

  9. Noise upon the sinusoids

    DEFF Research Database (Denmark)

    Jensen, Karl Kristoffer

    2005-01-01

    Sinusoids are used for making harmonic and other Sounds. In order to having life in the sounds and adding a wide variety of noises, irregularities are inserted in the frequency and amplitudes. A simple and intuitive noise model is presented, consisting of a low-pass filtered noise, and having...... control for strength and bandwidth. The noise is added on the frequency and amplitudes of the sinusoids, and the resulting irregularity's (jitter and shimmer) bandwidth is derived. This, together with an overview of investigation methods of the jitter and shimmer results in an analysis of the necessary...... samplerate of the shimmer and jitter. A harmonic model introduces individual and common irregularity, and adds a correlation control. The model has been implemented in max/msp and used in contemporary Music compositions....

  10. Acoustics Noise Test Cell

    Data.gov (United States)

    Federal Laboratory Consortium — The Acoustic Noise Test Cell at the NASA/Caltech Jet Propulsion Laboratory (JPL) is located adjacent to the large vibration system; both are located in a class 10K...

  11. Conservative Noise Filters

    Directory of Open Access Journals (Sweden)

    Mona M.Jamjoom

    2016-05-01

    Full Text Available Noisy training data have a huge negative impact on machine learning algorithms. Noise-filtering algorithms have been proposed to eliminate such noisy instances. In this work, we empirically show that the most popular noise-filtering algorithms have a large False Positive (FP error rate. In other words, these noise filters mistakenly identify genuine instances as outliers and eliminate them. Therefore, we propose more conservative outlier identification criteria that improve the FP error rate and, thus, the performance of the noise filters. With the new filter, an instance is eliminated if and only if it is misclassified by a mutual decision of Naïve Bayesian (NB classifier and the original filtering criteria being used. The number of genuine instances that are incorrectly eliminated is reduced as a result, thereby improving the classification accuracy.

  12. Noise and Neuronal Heterogeneity

    CERN Document Server

    Barber, Michael J

    2010-01-01

    We consider signal transaction in a simple neuronal model featuring intrinsic noise. The presence of noise limits the precision of neural responses and impacts the quality of neural signal transduction. We assess the signal transduction quality in relation to the level of noise, and show it to be maximized by a non-zero level of noise, analogous to the stochastic resonance effect. The quality enhancement occurs for a finite range of stimuli to a single neuron; we show how to construct networks of neurons that extend the range. The range increases more rapidly with network size when we make use of heterogeneous populations of neurons with a variety of thresholds, rather than homogeneous populations of neurons all with the same threshold. The limited precision of neural responses thus can have a direct effect on the optimal network structure, with diverse functional properties of the constituent neurons supporting an economical information processing strategy that reduces the metabolic costs of handling a broad...

  13. Jet Engine Noise Reduction

    Science.gov (United States)

    2009-04-01

    Technology Solutions, Lockheed Martin Robert S. Carnes , M.D. NRAC Member, Battelle Memorial Institute MajGen Paul A. Fratarangelo, USMC (Ret) NRAC...Development, Acquisition) (VADM Architzel). The Naval Research Advisory Committee members (Bowes, Bowler, Carnes and Fratarangelo) have broad...Lockheed Martin ADP Boeing: Jet Engine Noise Reduction for Tactical Fighter Aircraft Mr. Tom Kaemming, K. Viswanathan, Ph . D. Tactical Jet Noise

  14. Active noise control primer

    CERN Document Server

    Snyder, Scott D

    2000-01-01

    Active noise control - the reduction of noise by generating an acoustic signal that actively interferes with the noise - has become an active area of basic research and engineering applications. The aim of this book is to present all of the basic knowledge one needs for assessing how useful active noise control will be for a given problem and then to provide some guidance for designing, setting up, and tuning an active noise-control system. Written for students who have no prior knowledge of acoustics, signal processing, or noise control but who do have a reasonable grasp of basic physics and mathematics, the book is short and descriptive. It leaves for more advanced texts or research monographs all mathematical details and proofs concerning vibrations, signal processing and the like. The book can thus be used in independent study, in a classroom with laboratories, or in conjunction with a kit for experiment or demonstration. Topics covered include: basic acoustics; human perception and sound; sound intensity...

  15. Noise composed of multiplication of two dichotomous noises

    Institute of Scientific and Technical Information of China (English)

    Li Jing-Hui

    2008-01-01

    In this paper, we introduce a noise which is composed of multiplication of two dichotomous noises, and derive the probability density and the statistical properties of this noise. The obtained results can help study the resonant activation phenomenon, the phenomenon of stochastic resonance, the transport of particles, and the nonequilibrium (phase) transition for the systems driven by this noise.

  16. Noise sensitivity and sleep disturbance

    NARCIS (Netherlands)

    Laszlo, H.E.; Janssen, S.A.; Babisch, W.; Hansell, A.L.

    2012-01-01

    It has been shown that noise induced health effects are strongly related to non-acoustical factors such as noise sensitivity. It is a stable personality trait and it can be conceptualised as a causal pathway confounder and/or effect modifier between noise and health. Furthermore noise sensitivity pa

  17. Community response to tramway noise

    NARCIS (Netherlands)

    Miedema, H.M.E.; Berg, R. van den

    1988-01-01

    A study concerning tramway noise is described and results are presented. The study consisted of a social survey and a noise measurement program. It appeared that tramway noise does not contribute to the annoyance of the total noise if tramway annoyance is substantially below road traffic annoyance

  18. Community response to tramway noise

    NARCIS (Netherlands)

    Miedema, H.M.E.; Berg, R. van den

    1988-01-01

    A study concerning tramway noise is described and results are presented. The study consisted of a social survey and a noise measurement program. It appeared that tramway noise does not contribute to the annoyance of the total noise if tramway annoyance is substantially below road traffic annoyance (

  19. Airport noise and teratogenesis

    Energy Technology Data Exchange (ETDEWEB)

    Edmonds, L.D.; Layde, P.M.; Erickson, J.D.

    1979-07-01

    It has been suggested that exposure to high-noise levels near major airports may cause increased incidence of birth defects in the offspring of parents residing near these airports. Using data gathered in Metropolitan Atlanta during 1970 to 1972, we compared the rates of seventeen categories of defects in high- and low-noise census tracts. No significant differences were observed. However, when we subdivided the category of central nervous system defects into several subcategories of specific defects, we noted a significantly increased incidence of spina bifida without hydrocephalus in the high-noise areas. Because of the small number of cases associated with this finding we did a matched case-control study using all cases of central nervous system defects born during the years 1968 to 1976. No significantly increased risk for residents in the high-noise areas was noted in this study. It is our opinion that noise or other factors associated with residence near airports are unlikely to be important environmental teratogens.

  20. Noise and Function

    CERN Document Server

    Weinstein, Steven

    2016-01-01

    Noise is widely understood to be something that interferes with a signal or process. Thus, it is generally thought to be destructive, obscuring signals and interfering with function. However, early in the 20th century, mechanical engineers found that mechanisms inducing additional vibration in mechanical systems could prevent sticking and hysteresis. This so-called "dither" noise was later introduced in an entirely different context at the advent of digital information transmission and recording in the early 1960s. Ironically, the addition of noise allows one to preserve information that would otherwise be lost when the signal or image is digitized. As we shall see, the benefits of added noise in these contexts are closely related to the phenomenon which has come to be known as stochastic resonance, the original version of which appealed to noise to explain how small periodic fluctuations in the eccentricity of the earth's orbit might be amplified in such a way as to bring about the observed periodic transiti...

  1. Lower Hearing Threshold by Noise

    Institute of Scientific and Technical Information of China (English)

    龙长才; 邵峰; 张燕萍; 秦佑国

    2004-01-01

    We demonstrate that noise can be a benefit factor that enables us to hear weaker signals. We measured the hearing thresholds of subjects for pure tone in different noise levels. The results show that pure tone thresholds with noise of some levels are lower than that without noise. The largest down-shift of the threshold by noise among the examined subjects is 5. 7dB, and the smallest is 1.7dB.

  2. Road Traffic Noise

    Science.gov (United States)

    Beckenbauer, Thomas

    Road traffic is the most interfering noise source in developed countries. According to a publication of the European Union (EU) at the end of the twentieth century [1], about 40% of the population in 15 EU member states is exposed to road traffic noise at mean levels exceeding 55 dB(A). Nearly 80 million people, 20% of the population, are exposed to levels exceeding 65 dB(A) during daytime and more than 30% of the population is exposed to levels exceeding 55 dB(A) during night time. Such high noise levels cause health risks and social disorders (aggressiveness, protest, and helplessness), interference of communication and disturbance of sleep; the long- and short-term consequences cause adverse cardiovascular effects, detrimental hormonal responses (stress hormones), and possible disturbance of the human metabolism (nutrition) and the immune system. Even performance at work and school could be impaired.

  3. Noise and Tinnitus

    Directory of Open Access Journals (Sweden)

    Mansoureh Adel Ghahraman

    1999-03-01

    Full Text Available Tinnitus from the Latin word tinnire meaning ringing is the perception of sound within the human ear in the absence of corresponding external sound. The most common cause is noise induced hearing loss. Tinnitus may be induced by an acoustic trauma or a permanent noise in the workplace. In case that Tinnitus is induced by acoustic trauma the site of lesion is commonly the base of the cochlea. Tinnitus in the senile population is mostly accompanying presbycusis. Although the incidence of permanent tinnitus following noise exposure is high, little is published about this issue. In the current article we are aimed at studying the prevalence of tinnitus in Minoo and other manufactures.

  4. ECG De-noising

    DEFF Research Database (Denmark)

    Kærgaard, Kevin; Jensen, Søren Hjøllund; Puthusserypady, Sadasivan

    2015-01-01

    Electrocardiogram (ECG) is a widely used noninvasive method to study the rhythmic activity of the heart and thereby to detect the abnormalities. However, these signals are often obscured by artifacts from various sources and minimization of these artifacts are of paramount important. This paper...... proposes two adaptive techniques, namely the EEMD-BLMS (Ensemble Empirical Mode Decomposition in conjunction with the Block Least Mean Square algorithm) and DWT-NN (Discrete Wavelet Transform followed by Neural Network) methods in minimizing the artifacts from recorded ECG signals, and compares...... their performance. These methods were first compared on two types of simulated noise corrupted ECG signals: Type-I (desired ECG+noise frequencies outside the ECG frequency band) and Type-II (ECG+noise frequencies both inside and outside the ECG frequency band). Subsequently, they were tested on real ECG recordings...

  5. Noise Source Location Optimization

    Directory of Open Access Journals (Sweden)

    Ed O’Keefe

    1994-01-01

    Full Text Available This article describes a method to determine locations of noise sources that minimize modal coupling in complex acoustic volumes. Using the acoustic source scattering capabilities of the boundary element method, predictions are made of mode shape and pressure levels due to various source locations. Combining knowledge of the pressure field with a multivariable function minimization technique, the source location generating minimum pressure levels can be determined. The analysis also allows for an objective comparison of “best/worst” locations. The technique was implemented on a personal computer for the U.S. Space Station, predicting 5–10 dB noise reduction using optimum source locations.

  6. Community response to noise.

    Science.gov (United States)

    Yano, Takashi; Gjestland, Truls; Lee, Soogab

    2012-01-01

    Activities from 2008 to 2011 by ICBEN community response to noise team were summarized. That is, individual community-based indexes such as community tolerance Level, Zuricher Fluglarm Index (ZFI) and Frankfurter Fluglarm Index (FFI/FNI) were newly proposed, differences in railway bonus between Europe and Asia were discussed by a Swedish survey, socio-acoustic surveys were reported from developing countries, and annoyance equivalents and dominant source models were proposed as the adequate combined noise model. Furthermore, not only negative, but also positive aspects of sound were discussed as soundscape studies. Finally, seven items were listed as future team activities.

  7. Community response to noise

    Directory of Open Access Journals (Sweden)

    Takashi Yano

    2012-01-01

    Full Text Available Activities from 2008 to 2011 by ICBEN community response to noise team were summarized. That is, individual community-based indexes such as community tolerance Level, Zuricher Fluglarm Index (ZFI and Frankfurter Fluglarm Index (FFI/FNI were newly proposed, differences in railway bonus between Europe and Asia were discussed by a Swedish survey, socio-acoustic surveys were reported from developing countries, and annoyance equivalents and dominant source models were proposed as the adequate combined noise model. Furthermore, not only negative, but also positive aspects of sound were discussed as soundscape studies. Finally, seven items were listed as future team activities.

  8. Deletions and recombinations with the RNA1 3' ends of different tobraviruses have created a multitude of tobacco rattle virus TCM-related RNA2 species in Alstroemeria and tulip.

    Science.gov (United States)

    Koenig, R; Lesemann, D-E; Pfeilstetter, E; Winter, S; Pleij, C W A

    2011-04-01

    In vegetatively propagated Alstroemeria plants that showed pronounced stunting and necrotic leaf spots, a tobravirus infection was diagnosed in which one tobacco rattle virus (TRV, strain AL) RNA1 species was associated with seven different RNA2 species. The latter differed considerably in size and in the types of their 3' RNA1-related sequences. The 5' RNA2-specific part of all these RNA2 molecules showed almost 100% sequence identity with that of RNA2 of the TRV isolate TCM from tulip, but in some of these RNA2 molecules it was shorter than in the TCM isolate, whereas in others it was longer. One of the TRV AL RNA2 molecules, i.e. TC3'PE-a, contained the full set of three full-length RNA2-specific ORFs (ORF2a, -2b and -2c), whereas the previously analysed TCM sequence contained only ORF2a and -2b. In four of these TRV AL RNA2 molecules, i.e. those that had a relatively short RNA2-specific part, the 3' end was identical to that of the cognate TRV AL RNA1, but in the other three, which had a long RNA2-specific part, it was closely related to that of pea early browning virus (PEBV) RNA1, which was not detected in the infected plants. A comparison with previously described TRV/PEBV RNA2 recombinants suggested that the various TRV AL RNA2 molecules may represent various steps and side steps in an evolutionary process, which is apt to open the wide host range of TRV also to PEBV-derived RNA2 species.

  9. Discovering Host Genes Involved in the Infection by the Tomato Yellow Leaf Curl Virus Complex and in the Establishment of Resistance to the Virus Using Tobacco Rattle Virus-based Post Transcriptional Gene Silencing

    Directory of Open Access Journals (Sweden)

    Rosa Lozano-Durán

    2013-03-01

    Full Text Available The development of high-throughput technologies allows for evaluating gene expression at the whole-genome level. Together with proteomic and metabolomic studies, these analyses have resulted in the identification of plant genes whose function or expression is altered as a consequence of pathogen attacks. Members of the Tomato yellow leaf curl virus (TYLCV complex are among the most important pathogens impairing production of agricultural crops worldwide. To understand how these geminiviruses subjugate plant defenses, and to devise counter-measures, it is essential to identify the host genes affected by infection and to determine their role in susceptible and resistant plants. We have used a reverse genetics approach based on Tobacco rattle virus-induced gene silencing (TRV-VIGS to uncover genes involved in viral infection of susceptible plants, and to identify genes underlying virus resistance. To identify host genes with a role in geminivirus infection, we have engineered a Nicotiana benthamiana line, coined 2IRGFP, which over-expresses GFP upon virus infection. With this system, we have achieved an accurate description of the dynamics of virus replication in space and time. Upon silencing selected N. benthamiana genes previously shown to be related to host response to geminivirus infection, we have identified eighteen genes involved in a wide array of cellular processes. Plant genes involved in geminivirus resistance were studied by comparing two tomato lines: one resistant (R, the other susceptible (S to the virus. Sixty-nine genes preferentially expressed in R tomatoes were identified by screening cDNA libraries from infected and uninfected R and S genotypes. Out of the 25 genes studied so far, the silencing of five led to the total collapse of resistance, suggesting their involvement in the resistance gene network. This review of our results indicates that TRV-VIGS is an exquisite reverse genetics tool that may provide new insights into the

  10. Psychoacoustic study on contribution of fan noise to engine noise

    Science.gov (United States)

    Zhang, Junhong; Liu, Hai; Bi, Fengrong; Ni, Guangjian; Zhang, Guichang; Lin, Jiewei; Yu, Hanzhengnan

    2012-07-01

    There are more researches on engine fan noise control focusing on reducing fan noise level through optimizing fan structure, and a lot of research achievements have been obtained. However, researches on the effect of fan noise to engine noise quality are lacking. The influences of the effects of fan structure optimization on the engine noise quality are unclear. Thus, there will be a decline in fan noise level, but the deterioration of engine noise quality. Aiming at the above problems, in consideration of fan structure design and engine noise quality, an innovative method to analyze the contribution of fan noise to engine noise quality using psychoacoustic theory is proposed. The noises of diesel engine installing different cooling fans are measured by using the acoustic pressure method. The experiment results are regarded as analysis samples. The model of sensory pleasantness is used to analyze the sound quality of a diesel engine with different cooling fans. Results show that after installing 10-blade fan in medium diameter the sensory pleasantness at each test point is increased, and the increase is 13.53% on average, which indicate the improvement of the engine noise quality. In order to verify the psychoacoustical analysis, the subjective assessment is carried out. The test result shows the noise quality of engine installed 10-blade fan in medium diameter is most superior. 1/3 octave frequency spectrum analysis is used to study the reason of the improvement of engine noise quality. It is found that after installing proper cooling fan the sound pressure level below 400 Hz are obviously increased, the frequency assignment and spectral envelope are more reasonable and a proper cooling fan can optimize the spectrum structure of the engine noise. The psychoacoustic study is applied in the contribution of fan noise to engine noise, and the idea of engine sound quality improvement through the structure optimization is proposed.

  11. Noise sources and noise suppression in CMOS imagers

    Science.gov (United States)

    Pain, Bedabrata; Cunningham, Thomas J.; Hancock, Bruce R.

    2004-01-01

    Mechanisms for noise coupling in CMOS imagers are complex, since unlike a CCD, a CMOS imager has to be considered as a full digital-system-on-a-chip, with a highly sensitive front-end. In this paper, we analyze the noise sources in a photodiode CMOS imager, and model their propagation through the signal chain to determine the nature and magnitude of noise coupling. We present methods for reduction of noise, and present measured data to show their viability. For temporal read noise reduction, we present pixel signal chain design techniques to achieve near 2 electrons read noise. We model the front-end reset noise both for conventional photodiode and CTIA type of pixels. For the suppression of reset noise, we present a column feedback-reset method to reduce reset noise below 6 electrons. For spatial noise reduction, we present the design of column signal chain that suppresses both spatial noise and power supply coupling noise. We conclude by identifying problems in low-noise design caused by dark current spatial distribution.

  12. Curing the noise epidemic

    Science.gov (United States)

    Mazer, Susan

    2005-09-01

    The argument is made that design does not stop when the fixed architectural and acoustical components are in place. Spaces live and breathe with the people who reside in them. Research and examples are presented that show that noise, auditory clutter, thrives on itself in hospitals. Application of the Lombard reflex studies fit into the hospital setting, but do not offer solutions as to how one might reduce the impact. In addition, the basis for looking at the noise component as a physical as well cultural dynamic will be addressed. Whether the result of the wrong conversation in the wrong place or the right conversation in an unfortunate place, talk mixed with sounds of technology is shown to cause its own symptoms. From heightened anxiety and stress to medical errors, staff burnout, or HIPAA violations, the case is made that noise is pandemic in hospitals and demands financial and operational investment. An explanation of how to reduce noise by design of the dynamic environment - equipment, technology, staff protocols is also provided.

  13. Tandem Cylinder Noise Predictions

    Science.gov (United States)

    Lockhard, David P.; Khorrami, Mehdi R.; CHoudhari, Meelan M.; Hutcheson, Florence V.; Brooks, Thomas F.; Stead, Daniel J.

    2007-01-01

    In an effort to better understand landing-gear noise sources, we have been examining a simplified configuration that still maintains some of the salient features of landing-gear flow fields. In particular, tandem cylinders have been studied because they model a variety of component level interactions. The present effort is directed at the case of two identical cylinders spatially separated in the streamwise direction by 3.7 diameters. Experimental measurements from the Basic Aerodynamic Research Tunnel (BART) and Quiet Flow Facility (QFF) at NASA Langley Research Center (LaRC) have provided steady surface pressures, detailed off-surface measurements of the flow field using Particle Image Velocimetry (PIV), hot-wire measurements in the wake of the rear cylinder, unsteady surface pressure data, and the radiated noise. The experiments were conducted at a Reynolds number of 166 105 based on the cylinder diameter. A trip was used on the upstream cylinder to insure a fully turbulent shedding process and simulate the effects of a high Reynolds number flow. The parallel computational effort uses the three-dimensional Navier-Stokes solver CFL3D with a hybrid, zonal turbulence model that turns off the turbulence production term everywhere except in a narrow ring surrounding solid surfaces. The current calculations further explore the influence of the grid resolution and spanwise extent on the flow and associated radiated noise. Extensive comparisons with the experimental data are used to assess the ability of the computations to simulate the details of the flow. The results show that the pressure fluctuations on the upstream cylinder, caused by vortex shedding, are smaller than those generated on the downstream cylinder by wake interaction. Consequently, the downstream cylinder dominates the noise radiation, producing an overall directivity pattern that is similar to that of an isolated cylinder. Only calculations based on the full length of the model span were able to

  14. Reduction of turbomachinery noise

    Science.gov (United States)

    Waitz, Ian A. (Inventor); Brookfield, John M. (Inventor); Sell, Julian (Inventor); Hayden, Belva J. (Inventor); Ingard, K. Uno (Inventor)

    1999-01-01

    In the invention, propagating broad band and tonal acoustic components of noise characteristic of interaction of a turbomachine blade wake, produced by a turbomachine blade as the blade rotates, with a turbomachine component downstream of the rotating blade, are reduced. This is accomplished by injection of fluid into the blade wake through a port in the rotor blade. The mass flow rate of the fluid injected into the blade wake is selected to reduce the momentum deficit of the wake to correspondingly increase the time-mean velocity of the wake and decrease the turbulent velocity fluctuations of the wake. With this fluid injection, reduction of both propagating broad band and tonal acoustic components of noise produced by interaction of the blade wake with a turbomachine component downstream of the rotating blade is achieved. In a further noise reduction technique, boundary layer fluid is suctioned into the turbomachine blade through a suction port on the side of the blade that is characterized as the relatively low-pressure blade side. As with the fluid injection technique, the mass flow rate of the fluid suctioned into the blade is here selected to reduce the momentum deficit of the wake to correspondingly increase the time-mean velocity of the wake and decrease the turbulent velocity fluctuations of the wake; reduction of both propagating broad band and tonal acoustic components of noise produced by interaction of the blade wake with a turbomachine component downstream of the rotating blade is achieved with this suction technique. Blowing and suction techniques are also provided in the invention for reducing noise associated with the wake produced by fluid flow around a stationary blade upstream of a rotating turbomachine.

  15. Annoyance of low frequency noise and traffic noise

    DEFF Research Database (Denmark)

    Mortensen, F.R.; Poulsen, Torben

    2001-01-01

    The annoyance of different low frequency noise sources was determined and compared to the annoyance from traffic noise. Twenty-two subjects participated in laboratory listening tests. The sounds were presented by loudspeakers in a listening room and the spectra of the low frequency noises were...

  16. Evaluating noise abatement measures using strategic noise maps

    NARCIS (Netherlands)

    Borst, H.C.; Miedema, H.M.E.; Laan, W.P.N. van der; Lohman, W.J.A.

    2006-01-01

    Noise annoyance due to transportation is widespread in industrialized countries and in urban areas in the developing countries. The European Noise Directive (END) requires an assessment of the noise situation as well as the formulation of action plans for the reduction of the number of people

  17. Evaluating noise abatement measures using strategic noise maps

    NARCIS (Netherlands)

    Borst, H.C.; Miedema, H.M.E.; Laan, W.P.N. van der; Lohman, W.J.A.

    2006-01-01

    Noise annoyance due to transportation is widespread in industrialized countries and in urban areas in the developing countries. The European Noise Directive (END) requires an assessment of the noise situation as well as the formulation of action plans for the reduction of the number of people harmfu

  18. Rating environmental noise on the basis of noise maps

    NARCIS (Netherlands)

    Miedema, H.M.E.; Borst, H.C.

    2006-01-01

    A system that rates noise on the basis of noise maps has been developed which is based on empirical exposure-response relationships, so that effects in the community will be lower if the system gives a better rating. It is consistent with noise metrics and effect endpoint chosen in the EU, i.e., it

  19. Noise sensitivity and reactions to noise and other environmental conditions

    NARCIS (Netherlands)

    Miedema, H.M.E.; Vos, H.

    2003-01-01

    This article integrates findings from the literature and new results regarding noise sensitivity. The new results are based on analyses of 28 combined datasets (N=23 038), and separate analyses of a large aircraft noise study (N=10939). Three topics regarding noise sensitivity are discussed, namely,

  20. Noise-Induced Hearing Loss

    Science.gov (United States)

    ... America Information For… Media Policy Makers Noise-Induced Hearing Loss Recommend on Facebook Tweet Share Compartir Hearing plays ... sounds over an extended period. Preventing Noise-Induced Hearing Loss Hearing loss caused by exposure to loud sound ...

  1. Noise Measurement in Microsensor Applications

    OpenAIRE

    Moghaddam, Saeed

    2016-01-01

    In this research, spectral coherence noise measurement technique is used to measure noise of capacitive accelerometers, based on measuring the spectral coherence and outputs of two identical sensors exposed to the same input stimulus. This effective technique can be applied to any sensor characterization problem where there is interest in distinguishing instrumental noise from background noise. The simulation study has been done in MATLAB to verify the proposed method reliability to calculate...

  2. Practical ranges of loudness levels of various types of environmental noise, including traffic noise, aircraft noise, and industrial noise

    NARCIS (Netherlands)

    Salomons, E.M.; Janssen, S.A.

    2011-01-01

    In environmental noise control one commonly employs the A-weighted sound level as an approximate measure of the effect of noise on people. A measure that is more closely related to direct human perception of noise is the loudness level. At constant A-weighted sound level, the loudness level of a noi

  3. Low-frequency noise complaints

    DEFF Research Database (Denmark)

    Pedersen, Christian Sejer; Møller, Henrik; Persson-Waye, Kerstin

    2006-01-01

    In Denmark and in other industrialized countries there are cases where people complain about annoying low-frequency or infrasonic noise in their homes. Besides noise annoyance people often report other adverse effects such as insomnia, headache, lack of concentration etc. In many cases the noise...

  4. NOISE IN TEXTILE MILLS

    Directory of Open Access Journals (Sweden)

    P. Meshgi

    1977-06-01

    Full Text Available The mean noise levels were measured in the different sections of six representative mills in the Isfahan area, and audiometric measurements were made in 282 male workers employed in these mills. The mean noise levels were on average 95 dBA in the weaving sections and 88 d BA in the spinning sections. The audiometric findings showed a significant loss of gearing in the textile workers as compared to controls who were employed in a quiet environment. The study indicated that noisiness depended; on the whole, on the age and number of machines deployed per unit area of shop-floor. On the basis of this study certain recommendations were made to improve the working conditions.

  5. Ex / Noise / CERN / Deerhoof

    CERN Multimedia

    CERN, SM18,

    2015-01-01

    Indie rockers Deerhoof battled with the noise of CERN’s magnet test facilities on 30 August 2015. The band visited CERN at the invitation of ATLAS physicist James Beacham, whose pilot project Ex/Noise/CERN collides experimental music artists with experimental particle physics. Credits: -Producer- CERN Video Productions James Beacham François Briard -Director- Noemi Caraban -Camera- Yann Krajewski Piotr Traczyk Noemi Caraban -Crane operator- Antonio Henrique Jorge-Costa -Live recording at CERN- Mixing at Rec studio/Geneva By Serge Morattel -Infography- Daniel Dominguez Noemi Caraban -Deerhoof- John Dieterich Satomi Matsuzaki Ed Rodriguez Greg Saunier w/Deron Pulley SPECIAL THANKS TO: Michal Strychalski Marta Bajko Maryline Charrondiere Luca Bottura Christian Giloux Rodrigue Faes Mariane Catallon Georgina Hobgen Hailey Reissman Marine Bass

  6. Strategies for Railway Noise

    Science.gov (United States)

    Bovey, E. C.

    1996-05-01

    Strategies are much talked about, but frequently lack any substance. The general concepts of strategic planning are discussed and the need for it to have a focus, i.e., a clear objective, are emphasized. A structural approach to strategic plan development is advocated, with a definition of the relevant issues being a prerequisite for success. Strategies, however, must be flexible and constantly reviewed even though the measures of success are often blurred. Railway noise is clearly amenable to strategic planning, but the issues will vary depending on the objectives of the organization. It is evident that railway noise technology, application and development, while important, needs to be substantially supplemented by other factors such as logistics and management issues to form an effective strategy in this domain.

  7. Noise Phobia in Dog

    Directory of Open Access Journals (Sweden)

    Mangle

    Full Text Available Fear of thunderstorms and other forms of noise phobia are common problems in dogs. Administering medications along with changing the pet’s environment, and using behavior modification techniques can help ease the fear. Above all, do not give your pet any attention or reward when he is showing signs of fear; this will only reinforce the fearful behavior. [Veterinary World 2008; 1(11.000: 351-352

  8. Aircraft Noise Prediction

    OpenAIRE

    2014-01-01

    This contribution addresses the state-of-the-art in the field of aircraft noise prediction, simulation and minimisation. The point of view taken in this context is that of comprehensive models that couple the various aircraft systems with the acoustic sources, the propagation and the flight trajectories. After an exhaustive review of the present predictive technologies in the relevant fields (airframe, propulsion, propagation, aircraft operations, trajectory optimisation), the paper add...

  9. Model of flicker noise effects on phase noise in oscillators

    Science.gov (United States)

    Centurelli, Francesco; Ercolani, Alessandro; Tommasino, Pasquale; Trifiletti, Alessandro

    2003-05-01

    Phase noise models that describe the near-carrier spectrum in an accurate but insightful way are needed, to better optimize the oscillator design. In this paper we present a model to describe the effect of flicker noise sources on the phase noise of an oscillator, that can be applied both to linear oscillators and to nonlinear structures like relaxation and ring oscillators, so extending previous works that considered only the effect of the flicker noise superimposed to the control voltage of a VCO. In the phase noise of an oscillator we can separate the effect of high frequency noise sources, that can be described by a short-time-constant system, and the effect of low frequency noises (mostly flicker sources), described by a system with time constants much slower than the oscillation period. Flicker noise has been considered to cause a change in the circuit bias point; this bias point change can be mapped in a shift of the oscillation frequency by exploiting Barkhausen conditions (for linear oscillators) or obtaining this link by simulations. The power spectral density of the oscillator can then be obtained as the probability distribution of the oscillation frequency, starting from the flicker noise probability distribution. If the effect of high frequency noise sources is also taken into account, the overall oscillator spectrum can be obtained as a convolution of the spectrum due to flicker sources with the Lorentzian-shaped spectrum due to white noise sources, in analogy with the description of inhomogeneous broadening of laser linewidth.

  10. Noise Analysis of MAIA System and Possible Noise Suppression

    Directory of Open Access Journals (Sweden)

    J. Svihlik

    2011-04-01

    Full Text Available This paper is devoted to the noise analysis and noise suppression in a system for double station observation of the meteors now known as MAIA (Meteor Automatic Imager and Analyzer. The noise analysis is based on acquisition of testing video sequences in different light conditions and their further statistical evaluation. The main goal is to find a suitable noise model and subsequently determine if the noise is signal dependent or not. Noise and image model in the wavelet domain should be based on Gaussian mixture model (GMM or Generalized Laplacian Model (GLM and the model parameters should be estimated by moment method. Furthermore, noise should be modeled by GMM or GLM also in the space domain. GMM and GLM allow to model various types of probability density functions. Finally the advanced denoising algorithm using Bayesian estimator is applied and its performance is verified.

  11. Physical Mechanisms of Seismometer Site Noise and Self-Noise

    Science.gov (United States)

    Bainbridge, G. S.; Parker, T.; Townsend, B.; Upadhyaya, S.

    2016-12-01

    Ideally any seismometer installation should have a noise level corresponding to a predefined specification, to ensure the noise level is below the signals of interest. In practice seismic data may contain unforeseen noise artifacts and may vary widely in quality from one station to another due to particular site conditions, problematic installation methods, or a defective or unsuitable instrument. Also some modes of ground motion can be considered as noise, for example local vibration or tilt motion obscuring teleseismic signals. In this study we present an analysis of the physical phenomena which most commonly cause noise artifacts in broadband seismic data, based on data from controlled laboratory experiments as well as field installations. Each different physical mechanism gives rise to noise with particular distinguishing characteristics which can enable the user to diagnose noise symptoms, trace them to a root cause, take corrective action, and evolve towards best practices for particular environments and use cases.

  12. Ambiguity functions and noise floor suppression in random noise radar

    Science.gov (United States)

    Axelsson, Sune R. J.

    2006-09-01

    Noise radar can be used in a great number of applications including SAR. The non-periodic waveform suppresses the range ambiguity and reduces the probability of intercept and interference. Due to the randomness of the waveform, a noise floor limiting the possible side lobe suppression accompanies the correlation integral involved. In strong clutter scenes with dominant reflectors, the induced noise floor can be too high and further suppression is needed. In this paper, the ambiguity function of random noise waveforms is first analyzed, and an improved formulation is introduced to include the noise floor effect. The use of mismatched filtering for improved sidelobe suppression is then discussed. Finally, an iterative subtraction algorithm is analyzed for noise floor cancellation in the presence of dominating reflectors. This method is successfully tested on random step frequency radar data and noise sodar data.

  13. Aircraft noise prediction

    Science.gov (United States)

    Filippone, Antonio

    2014-07-01

    This contribution addresses the state-of-the-art in the field of aircraft noise prediction, simulation and minimisation. The point of view taken in this context is that of comprehensive models that couple the various aircraft systems with the acoustic sources, the propagation and the flight trajectories. After an exhaustive review of the present predictive technologies in the relevant fields (airframe, propulsion, propagation, aircraft operations, trajectory optimisation), the paper addresses items for further research and development. Examples are shown for several airplanes, including the Airbus A319-100 (CFM engines), the Bombardier Dash8-Q400 (PW150 engines, Dowty R408 propellers) and the Boeing B737-800 (CFM engines). Predictions are done with the flight mechanics code FLIGHT. The transfer function between flight mechanics and the noise prediction is discussed in some details, along with the numerical procedures for validation and verification. Some code-to-code comparisons are shown. It is contended that the field of aircraft noise prediction has not yet reached a sufficient level of maturity. In particular, some parametric effects cannot be investigated, issues of accuracy are not currently addressed, and validation standards are still lacking.

  14. Noise tolerant spatiotemporal chaos computing

    Energy Technology Data Exchange (ETDEWEB)

    Kia, Behnam; Kia, Sarvenaz; Ditto, William L. [Department of Physics and Astronomy, University of Hawaii at Manoa, Honolulu, Hawaii 96822 (United States); Lindner, John F. [Physics Department, The College of Wooster, Wooster, Ohio 44691 (United States); Sinha, Sudeshna [Indian Institute of Science Education and Research (IISER), Mohali, Punjab 140306 (India)

    2014-12-01

    We introduce and design a noise tolerant chaos computing system based on a coupled map lattice (CML) and the noise reduction capabilities inherent in coupled dynamical systems. The resulting spatiotemporal chaos computing system is more robust to noise than a single map chaos computing system. In this CML based approach to computing, under the coupled dynamics, the local noise from different nodes of the lattice diffuses across the lattice, and it attenuates each other's effects, resulting in a system with less noise content and a more robust chaos computing architecture.

  15. Noise tolerant spatiotemporal chaos computing.

    Science.gov (United States)

    Kia, Behnam; Kia, Sarvenaz; Lindner, John F; Sinha, Sudeshna; Ditto, William L

    2014-12-01

    We introduce and design a noise tolerant chaos computing system based on a coupled map lattice (CML) and the noise reduction capabilities inherent in coupled dynamical systems. The resulting spatiotemporal chaos computing system is more robust to noise than a single map chaos computing system. In this CML based approach to computing, under the coupled dynamics, the local noise from different nodes of the lattice diffuses across the lattice, and it attenuates each other's effects, resulting in a system with less noise content and a more robust chaos computing architecture.

  16. Noise-induced coherent switch

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Taking the famous genetic toggle switch as an example,we numerically investigated the effect of noise on bistability.We found that extrinsic noise resulting from stochastic fluctuations in synthesis and degradation rates and from the environmental fluctuation in gene regulatory processes can induce coherent switch,and that there is an optimal noise intensity such that the noise not only can induce this switch,but also can amplify a weak input signal.In addition,we found that the intrinsic noise introduced through the Poisson τ-leap algorithm cannot induce such a switch.

  17. Noise-Mediated Generalized Synchronization

    Institute of Scientific and Technical Information of China (English)

    CHEN Yue-Hua; WU Zhi-Yuan; YANG Jun-Zhong

    2007-01-01

    @@ We investigate a drive-response system by considering the impacts of noise on generalized synchronization (GS).It is found that a small amount of noise can turn the system from desynchronization to the GS state in the resonant case no matter how noise is injected into the system. In the non-resonant case, noise with intensity in a certain range is helpful in building GS only when the noise is injected to the driving system. The mechanism behind the observed phenomena is discussed.

  18. Noise Emission from Laboratory Air Blowers

    Science.gov (United States)

    Rossing, Thomas D.; Windham, Betty

    1978-01-01

    Product noise ratings for a number of laboratory air blowers are reported and several recommendations for reducing laboratory noise from air blowers are given. Relevant noise ratings and methods for measuring noise emission of appliances are discussed. (BB)

  19. Calibration of an audio frequency noise generator

    DEFF Research Database (Denmark)

    Diamond, Joseph M.

    1966-01-01

    A noise generator of known output is very convenient in noise measurement. At low audio frequencies, however, all devices, including noise sources, may be affected by excess noise (1/f noise). It is therefore very desirable to be able to check the spectral density of a noise source before it is u...

  20. Dynamical decoupling noise spectroscopy

    CERN Document Server

    Alvarez, Gonzalo A

    2011-01-01

    Decoherence is one of the most important obstacles that must be overcome in quantum information processing. It depends on the qubit-environment coupling strength, but also on the spectral composition of the noise generated by the environment. If the spectral density is known, fighting the effect of decoherence can be made more effective. Applying sequences of inversion pulses to the qubit system, we generate effective filter functions that probe the environmental spectral density. Comparing different pulse sequences, we recover the complete spectral density function and distinguish different contributions to the overall decoherence.

  1. Noise hazard course

    CERN Multimedia

    2003-01-01

    A 1/2 day course to promote awareness of the risks incurred by noise at the work place and recommendations to settle them. Next course Wednesday 24th September 2003. Costs are covered by TIS, Jacques Coillard from Bureau Véritas will present the course. Registration is obligatory. For more information and to enrol on this course go to the safety section of Human Resources Training and Development web pages, or contact : Ana-Paula Bernardes/TIS-GS (71385) or e-mail Ana-Paula.Bernardes@cern.ch

  2. Noise hazard course

    CERN Multimedia

    2003-01-01

    A 1/2 day course to promote awareness of the risks incurred by noise at the work place and recommendations to settle them. Next course Wednesday 24th September 2003. Costs are covered by TIS, Jacques Coillard from Bureau Véritas will present the course. Registration is obligatory. For more information and to enrol on this course go to the safety section of Human Resources Training and Development web pages, or contact: Ana-Paula Bernardes/TIS-GS (71385) or e-mail Ana-Paula.Bernardes@cern.ch

  3. Monitoring of Noise During Ganeshotsav

    Directory of Open Access Journals (Sweden)

    Mrs. P. Saler

    2011-09-01

    Full Text Available Sound is a form of energy emitted by a vibrating body causing change in pressure of the surrounding elastic medium through which energy is transmitted. Noise has been defined as unwanted sound. Noise is a disturbance to the human environment which is escalating at a high rate. There are numerous effects of noise on human and environment due to the increase in noise pollution slowly, insensibly; we seem to accept noise and the physiological and psychological deterioration that accompanies it as an inevitable part of our lives. Althoughattempts have been made to regulate noise pollution by setting standards for some of the major sources of noise, we often are unable to monitor them. One such source of noise in India is celebration of festival and especially in Maharashtra, the biggest festival- Ganeshostav. The way noise levels are increasing year by year during this festival, it seems we enjoy these sounds, though it has harmful effects on Human Health and Environment. This paper focuses on study of noise pollution during Ganesh Festival and also its other causes and effects.

  4. Occupational noise in printing companies.

    Science.gov (United States)

    Mihailovic, Aleksandra; Grujic, Selena D; Kiurski, Jelena; Krstic, Jelena; Oros, Ivana; Kovacevic, Ilija

    2011-10-01

    The extent of noise in five printing companies in Novi Sad, Serbia, was determined using TES-1358A Sound Analyzer with RS-232 Interface. The data on equivalent A-level (dBA), as well as, maximum and minimum sound pressure levels were collected. It was found that folders and offset printing units are the predominant noise sources, with the average L (eq) levels of 87.66 and 82.7 dBA, respectively. Forty percent of the machines produced noise levels above the limiting threshold level of 85 dBA, allowed by law. The noise in all printing companies was dominated by higher frequency noise, and the maximum level mostly appeared at 4,000 Hz. For offset printing machines and folders, the means of L (eq) levels exceeded the permissible levels given by NR-80 curve at higher frequencies. There are no published studies of occupational noise and hearing impairment of workers exposed to hazardous noise in printing industry in Serbia. More extensive studies are needed to determine the exact impact of noise on the workers. Technical and organizational measures in order to control noise and prevent noise exposure, and general hearing conservation program to protect workers, should be introduced in printing industry.

  5. Development of Active Noise Control System for Quieting Transformer Noise

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Bok Kyu; Song, Seik Young; Choi, Huo Yul [Korea Electric Power Research Institute, Taejon (Korea, Republic of); Yun, Dae Hea; Lee, Hyuk Jae [Korea Electrotechnology Research Institute, Changwon (Korea, Republic of)

    1997-12-31

    The passive noise control technique made use of sound-absorbing or soundproofing materials, so it required a large area and high cost for installation and had a drawback of poor performance at low frequency. Compared to this, the Active Noise Control attenuates noise sound pressure by using secondary source which has same performance ay low-frequency. Furthermore, it is able to save space and expenses. - research on adaptive algorithms - evaluation of global attenuation of the control - computer simulation - real-time Active Noise Control System Hardware Implementation - ANC system setting in the noisy area.

  6. Development of Active Noise Control System for Quieting Transformer Noise

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Bok Kyu; Song, Seik Young; Choi, Huo Yul [Korea Electric Power Research Institute, Taejon (Korea, Republic of); Yun, Dae Hea; Lee, Hyuk Jae [Korea Electrotechnology Research Institute, Changwon (Korea, Republic of)

    1997-12-31

    The passive noise control technique made use of sound-absorbing or soundproofing materials, so it required a large area and high cost for installation and had a drawback of poor performance at low frequency. Compared to this, the Active Noise Control attenuates noise sound pressure by using secondary source which has same performance ay low-frequency. Furthermore, it is able to save space and expenses. - research on adaptive algorithms - evaluation of global attenuation of the control - computer simulation - real-time Active Noise Control System Hardware Implementation - ANC system setting in the noisy area.

  7. Noise in Lead Beta Alumina.

    Science.gov (United States)

    1987-05-01

    single crystal and ceramic samples. The temperature dependance for diffusion noise (I>O,1OHz) is greater than can be accounted for by Equation (1). This...3.2 3.3 3.4 3.5 3.6 3.7 1000/T IN 1/9 Figure 2. Temperature Dependance of Nyqutst Noise (5kHz) and Diffusion Noise (lOHz) of Single Crystal and

  8. Noise of sliding rough contact

    Science.gov (United States)

    Le Bot, Alain

    2017-01-01

    This article is a discussion about the origin of friction noise produced when rubbing solids having rough surfaces. We show that noise emerges from numerous impacts into the contact between antagonist asperities of surfaces. Prediction of sound sources reduces to a statistical problem of contact mechanics. On the other hand, contact is also responsible of dissipation of vibration. This leads to the paradoxical result that the noise may not be proportional to the number of sources.

  9. Road traffic noise and stroke

    DEFF Research Database (Denmark)

    Sørensen, Mette; Hvidberg, Martin; Andersen, Zorana J

    2011-01-01

    Epidemiological studies suggest that long-term exposure to road traffic noise increases the risk of cardiovascular disorders. The aim of this study was to investigate the relation between exposure to road traffic noise and risk for stroke, which has not been studied before.......Epidemiological studies suggest that long-term exposure to road traffic noise increases the risk of cardiovascular disorders. The aim of this study was to investigate the relation between exposure to road traffic noise and risk for stroke, which has not been studied before....

  10. Noise Pollution and Health Effects

    Directory of Open Access Journals (Sweden)

    Geravandi

    2015-01-01

    Full Text Available Background Noise pollution is of particular importance due to the physical and psychological effects on humans. Noise is a stressor that affects the autonomic nervous system and the endocrine system. Noise is also a threat to marine and terrestrial ecosystems. Health risks from noise are correlated with road traffic. In other words, noise health effects are the health consequences of elevated sound levels. Objectives This study aims to determine the effect of noise pollution (near roadways on health issues in Ahvaz, Iran. Materials and Methods In this cross-sectional study, equivalent sound pressure level were measured by sound level meters TES-1353 in 75 locations around 4 roadways, which had a high load of traffic in Ahvaz City during day time. During the study, 820 measurements were recorded at measuring stations, for 7 days per week with 1-hour interval between each measurement. Statistical analysis was carried out by SPSS software. Results According to the research findings, the equivalent sound pressure levels in all stations were 76.28 ± 3.12 dB (Mean ± SD. According to sound measurements and the survey questionnaire, noise pollution is higher than EPA (US Environmental Protection Agency and Iran standard level. Based on result of this study the worst noise health effects were the nervousness and sleep quality during 2012. Conclusions According to the results of this study, with increasing load of traffic, there is an increasing need for proper consideration plans to control noise pollution and prevent its effects.

  11. Adjusting phenotypes by noise control.

    Directory of Open Access Journals (Sweden)

    Kyung H Kim

    2012-01-01

    Full Text Available Genetically identical cells can show phenotypic variability. This is often caused by stochastic events that originate from randomness in biochemical processes involving in gene expression and other extrinsic cellular processes. From an engineering perspective, there have been efforts focused on theory and experiments to control noise levels by perturbing and replacing gene network components. However, systematic methods for noise control are lacking mainly due to the intractable mathematical structure of noise propagation through reaction networks. Here, we provide a numerical analysis method by quantifying the parametric sensitivity of noise characteristics at the level of the linear noise approximation. Our analysis is readily applicable to various types of noise control and to different types of system; for example, we can orthogonally control the mean and noise levels and can control system dynamics such as noisy oscillations. As an illustration we applied our method to HIV and yeast gene expression systems and metabolic networks. The oscillatory signal control was applied to p53 oscillations from DNA damage. Furthermore, we showed that the efficiency of orthogonal control can be enhanced by applying extrinsic noise and feedback. Our noise control analysis can be applied to any stochastic model belonging to continuous time Markovian systems such as biological and chemical reaction systems, and even computer and social networks. We anticipate the proposed analysis to be a useful tool for designing and controlling synthetic gene networks.

  12. High level white noise generator

    Science.gov (United States)

    Borkowski, Casimer J.; Blalock, Theron V.

    1979-01-01

    A wide band, stable, random noise source with a high and well-defined output power spectral density is provided which may be used for accurate calibration of Johnson Noise Power Thermometers (JNPT) and other applications requiring a stable, wide band, well-defined noise power spectral density. The noise source is based on the fact that the open-circuit thermal noise voltage of a feedback resistor, connecting the output to the input of a special inverting amplifier, is available at the amplifier output from an equivalent low output impedance caused by the feedback mechanism. The noise power spectral density level at the noise source output is equivalent to the density of the open-circuit thermal noise or a 100 ohm resistor at a temperature of approximately 64,000 Kelvins. The noise source has an output power spectral density that is flat to within 0.1% (0.0043 db) in the frequency range of from 1 KHz to 100 KHz which brackets typical passbands of the signal-processing channels of JNPT's. Two embodiments, one of higher accuracy that is suitable for use as a standards instrument and another that is particularly adapted for ambient temperature operation, are illustrated in this application.

  13. Physiological, Psychological, and Social Effects of Noise

    Science.gov (United States)

    Kryter, K. D.

    1984-01-01

    The physiological, and behavioral effects of noise on man are investigated. Basic parameters such as definitions of noise, measuring techniques of noise, and the physiology of the ear are presented prior to the development of topics on hearing loss, speech communication in noise, social effects of noise, and the health effects of noise pollution. Recommendations for the assessment and subsequent control of noise is included.

  14. Quantum Noise Locking

    CERN Document Server

    McKenzie, K; Goda, K; Lam, P K; Grosse, N; Gray, M B; Mavalvala, N; McClelland, D E; Kenzie, Kirk Mc; Mikhailov, Eugeniy; Goda, Keisuke; Lam, Ping Koy; Grosse, Nicolai; Gray, Malcolm B.; Mavalvala, Nergis; Clelland, David E. Mc

    2005-01-01

    Quantum optical states which have no coherent amplitude, such as squeezed vacuum states, can not rely on standard readout techniques to generate error signals for control of the quadrature phase. Here we investigate the use of asymmetry in the quadrature variances to obtain a phase-sensitive readout and to lock the phase of a squeezed vacuum state, a technique which we call noise locking (NL). We carry out a theoretical derivation of the NL error signal and the associated stability of the squeezed and anti-squeezed lock points. Experimental data for the NL technique both in the presence and absence of coherent fields are shown, including a comparison with coherent locking techniques. Finally, we use NL to enable a stable readout of the squeezed vacuum state on a homodyne detector.

  15. Quantum noise locking

    Energy Technology Data Exchange (ETDEWEB)

    McKenzie, Kirk [Center for Gravitational Physics, Department of Physics, Faculty of Science, Australian National University, ACT 0200 (Australia); Mikhailov, Eugeniy E [LIGO Laboratory, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Goda, Keisuke [LIGO Laboratory, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Lam, Ping Koy [Quantum Optics Group, Department of Physics, Faculty of Science, Australian National University, ACT 0200 (Australia); Grosse, Nicolai [Quantum Optics Group, Department of Physics, Faculty of Science, Australian National University, ACT 0200 (Australia); Gray, Malcolm B [Center for Gravitational Physics, Department of Physics, Faculty of Science, Australian National University, ACT 0200 (Australia); Mavalvala, Nergis [LIGO Laboratory, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); McClelland, David E [Center for Gravitational Physics, Department of Physics, Faculty of Science, Australian National University, ACT 0200 (Australia)

    2005-10-01

    Quantum optical states which have no coherent amplitude, such as squeezed vacuum states, cannot rely on standard readout techniques to generate error signals for control of the quadrature phase. Here we investigate the use of asymmetry in the quadrature variances to obtain a phase-sensitive readout and to lock the phase of a squeezed vacuum state, a technique which we call noise locking (NL). We carry out a theoretical derivation of the NL error signal and the associated stability of the squeezed and anti-squeezed lock points. Experimental data for the NL technique both in the presence and absence of coherent fields are shown, including a comparison with coherent locking techniques. Finally, we use NL to enable a stable readout of the squeezed vacuum state on a homodyne detector.

  16. Active Noise Control of Radiated Noise from Jets Originating NASA

    Science.gov (United States)

    Doty, Michael J.; Fuller, Christopher R.; Schiller, Noah H.; Turner, Travis L.

    2013-01-01

    The reduction of jet noise using a closed-loop active noise control system with highbandwidth active chevrons was investigated. The high frequency energy introduced by piezoelectrically-driven chevrons was demonstrated to achieve a broadband reduction of jet noise, presumably due to the suppression of large-scale turbulence. For a nozzle with one active chevron, benefits of up to 0.8 dB overall sound pressure level (OASPL) were observed compared to a static chevron nozzle near the maximum noise emission angle, and benefits of up to 1.9 dB OASPL were observed compared to a baseline nozzle with no chevrons. The closed-loop actuation system was able to effectively reduce noise at select frequencies by 1-3 dB. However, integrated OASPL did not indicate further reduction beyond the open-loop benefits, most likely due to the preliminary controller design, which was focused on narrowband performance.

  17. A review and tutorial discussion of noise and signal-to-noise ratios in analytical spectrometry—III. Multiplicative noises

    NARCIS (Netherlands)

    Alkemade, C.T.J.; Snelleman, W.; Boutilier, G.D.; Winefordner, J.D.

    1980-01-01

    In this review, signal-to-noise ratios are discussed in a tutorial fashion for the case of multiplicative noise. Multiplicative noise is introduced simultaneously with the analyte signal and is therefore much more difficult to reduce than additive noise. The sources of noise, the mathematical repres

  18. Fast High-Quality Noise

    DEFF Research Database (Denmark)

    Frisvad, Jeppe Revall; Wyvill, Geoff

    2007-01-01

    At the moment the noise functions available in a graphics programmer's toolbox are either slow to compute or they involve grid-line artifacts making them of lower quality. In this paper we present a real-time noise computation with no grid-line artifacts or other regularity problems. In other wor...

  19. Consumer oriented product noise testing

    Science.gov (United States)

    Blomberg, Les

    2005-09-01

    This paper explores the need for product noise measurements and how best to meet that need in the near future. Currently there is only a small market place for quieter consumer products. This is not because of lack of interest. No one really wants to announce to everyone in their house that they just flushed the toilet, few really want the entire neighborhood to know they are mowing their yard, etc. The small market place is primarily due to a lack of regulations on product noise, a lack of information easily available to consumers about which products are quieter, and market consolidation resulting in fewer manufacturers, most of whom are unwilling to emphasize their quieter products at the risk of eroding sales of their noisier ones (that currently have greater market share). In the absence of the EPA fulfilling its statutory requirement to regulate and label product noise under the Noise Control Act of 1972, and with the unwillingness of most industries to voluntarily publish accurate product noise data, there is a significant role for ``Consumer Oriented Product Noise Testing.'' This paper explores the Noise Pollution Clearinghouse's ongoing and planned product noise testing, evaluating its advantages, disadvantages, and limitations.

  20. Noise and health of children

    NARCIS (Netherlands)

    Passchier, W.

    2000-01-01

    The world of the child is becoming noisier and noisier. Compared to the mid-fifties environ-mental noise levels (sources such as road traffic, aircraft) increased substantially, causing higher noise levels during day- and night-time at home, at school and during out- and indoors leisure time activit

  1. Generation of spatiotemporal colored noise

    OpenAIRE

    García Ojalvo, Jordi; Ramírez de la Piscina Millán, Laureano; Sancho, Jose Maria

    1992-01-01

    We develop an algorithm to simulate a Gaussian stochastic process that is non-δ-correlated in both space and time coordinates. The colored noise obeys a linear reaction-diffusion Langevin equation with Gaussian white noise. This equation is exactly simulated in a discrete Fourier space. Peer Reviewed

  2. Divide and conquer spot noise

    NARCIS (Netherlands)

    Leeuw, W.C. de; Liere, R. van

    1997-01-01

    The design and implementation of an interactive spot noise algorithm is presented. Spot noise is a technique which utilizes texture for the visualization of flow fields. Various design tradeoffs are discussed that allow an optimal implementation on a range of high end graphical workstations. Two app

  3. Noise exposure and public health

    NARCIS (Netherlands)

    Passchier-Vermeer, W.; Passchier, W.F.

    2000-01-01

    Exposure to noise constitutes a health risk. There is sufficient scientific evidence that noise exposure can induce hearing impairment, hypertension and ischemic heart disease, annoyance, sleep disturbance, and decreased school performance. For other effects such as changes in the immune system and

  4. Predicting Noise From Wind Turbines

    Science.gov (United States)

    Grosveld, Ferdinand W.

    1990-01-01

    Computer program WINDY predicts broadband noise spectra of horizontal-axis wind-turbine generators. Enables adequate assessment of impact of broadband wind-turbine noise. Effects of turbulence, trailing-edge wakes, and bluntness taken into account. Program has practical application in design and siting of wind-turbine machines acceptable to community. Written in GW-Basic.

  5. Quantum noise in superluminescent diodes

    Energy Technology Data Exchange (ETDEWEB)

    Yuvek, A.M.; Taylor, H.F.; Goldberg, L.; Weller, J.F.; Dandridge, A.

    1986-04-01

    Intensity noise in a superluminescent diode (SLD) has been studied over the frequency range from 100 Hz to 2 MHz. The ''1/F'' noise which dominates at low frequencies (<59 kHz) is superceded by a flat ''white noise'' spectrum at higher frequencies (> 500 5Hz). A more extensive investigation has been carried out in this higher frequency regime, where the intensity noise is assumed to result from quantum fluctuation effects. For a given SLD driving current, the excess noise power is found to be a linear function of photodetector current to the maximum observed level of 12 db. These results agree well with the behavior predicted by a quantum amplifier model for the SLD.

  6. Recent Advances in Studies of Current Noise

    Science.gov (United States)

    Blanter, Yaroslav M.

    This is a brief review of recent activities in the field of current noise intended for newcomers. We first briefly discuss main properties of shot noise in nanostructures, and then turn to recent developments, concentrating on issues related to experimental progress: non-symmetrized cumulants and quantum noise; counting statistics; super-Poissonian noise; current noise and interferometry

  7. 23 CFR 772.19 - Construction noise.

    Science.gov (United States)

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Construction noise. 772.19 Section 772.19 Highways... ABATEMENT OF HIGHWAY TRAFFIC NOISE AND CONSTRUCTION NOISE § 772.19 Construction noise. The following general... may be affected by noise from construction of the project. The identification is to be...

  8. Active Noise Control for Vehicle Exhaust Noise Reduction

    Institute of Scientific and Technical Information of China (English)

    李克强; 杨殿阁; 郑四发; 连小珉; 田中丈晴

    2003-01-01

    An active noise control (ANC) method was developed for exhaust noise reduction for medium-duty diesel trucks. A modified variable step size least mean squares (LMS) algorithm was used for the controller in a variable environment that considered the vehicle's acceleration characteristics. The variable step size time-based synchronized filtered-x LMS method (SFX-TB) used an adaptive algorithm that was more efficient than the conventional filtered-x LMS algorithm. The simulation and the experimental tests show that the control trackability and stability provided by the algorithm during acceleration enable the ANC system to effectively reduce the vehicle exhaust noise.

  9. Noise exposure in oil mills

    Directory of Open Access Journals (Sweden)

    Prasanna Kumar G

    2008-01-01

    Full Text Available Context: Noise of machines in various agro-based industries was found to be the major occupational hazard for the workers of industries. The predominant noise sources need to be identified and the causes of high noise need to be studied to undertake the appropriate measures to reduce the noise level in one of the major agro-based industries, oil mills. Aims: To identify the predominant noise sources in the workrooms of oil mills. To study the causes of noise in oil mills. To measure the extent of noise exposure of oil mill workers. To examine the response of workers towards noise, so that appropriate measures can be undertaken to minimize the noise exposure. Settings and Design: A noise survey was conducted in the three renowned oil mills of north-eastern region of India. Materials and Methods: Information like output capacity, size of power source, maintenance condition of the machines and workroom configurations of the oil mills was collected by personal observations and enquiry with the owner of the mill. Using a Sound Level Meter (SLM (Model-824, Larson and Davis, USA, equivalent SPL was measured at operator′s ear level in the working zone of the workers near each machine of the mills. In order to study the variation of SPL in the workrooms of the oil mill throughout its operation, equivalent SPL was measured at two appropriate locations of working zone of the workers in each mill. For conducting the noise survey, the guidelines of Canadian Centre for Occupational Health and Safety (CCOHS were followed. Grid points were marked on the floor of the workroom of the oil mill at a spacing of 1 m x 1 m. SPL at grid points were measured at about 1.5 m above the floor. The direction of the SLM was towards the nearby noisy source. To increase accuracy, two replications were taken at each grid point. All the data were recorded for 30 sec. At the end of the experiment, data were downloaded to a personal computer. With the help of utility software of

  10. Thermal noise engines

    CERN Document Server

    Kish, Laszlo B

    2010-01-01

    Electrical heat engines driven by the Johnson-Nyquist noise of resistors are introduced. They utilize Coulomb's law and the fluctuation-dissipation theorem of statistical physics that is the reverse phenomenon of heat dissipation in a resistor. No steams, gases, liquids, photons, fuel, combustion, phase transition, or exhaust/pollution are present here. In these engines, instead of heat reservoirs, cylinders, pistons and valves, resistors, capacitors and switches are the building elements. For the best performance, a large number of parallel engines must be integrated and the characteristic size of the elementary engine must be at the 10 nanometers scale. At room temperature, in the most idealistic case, a two-dimensional ensemble of engines of 25 nanometer characteristic size integrated on a 2.5x2.5 cm silicon wafer with 12 Celsius degree temperature difference between the warm-source and the cold-sink would produce a specific power of about 0.8 Watt. Regular and coherent (correlated-cylinder states) version...

  11. Rocket noise - A review

    Science.gov (United States)

    McInerny, S. A.

    1990-10-01

    This paper reviews what is known about far-field rocket noise from the controlled studies of the late 1950s and 1960s and from launch data. The peak dimensionless frequency, the dependence of overall sound power on exhaust parameters, and the directivity of the overall sound power of rockets are compared to those of subsonic jets and turbo-jets. The location of the dominant sound source in the rocket exhaust plume and the mean flow velocity in this region are discussed and shown to provide a qualitative explanation for the low peak Strouhal number, fD(e)/V(e), and large angle of maximum directivity. Lastly, two empirical prediction methods are compared with data from launches of a Titan family vehicle (two, solid rocket motors of 5.7 x 10 to the 6th N thrust each) and the Saturn V (five, liquid oxygen/rocket propellant engines of 6.7 x 10 to the 6th N thrust, each). The agreement is favorable. In contrast, these methods appear to overpredict the far-field sound pressure levels generated by the Space Shuttle.

  12. Signal with Flat Phase Noise Using a Carrier and the Power Spectral Density of White Noise for Phase Noise Standards

    Science.gov (United States)

    Watabe, Ken-ichi; Yanagimachi, Shinya; Ikegami, Takeshi; Iida, Hitoshi; Shimada, Yozo

    2012-01-01

    We have realized a phase noise standard of a signal with a -100 dBc/Hz flat phase noise at 10 MHz for Fourier frequencies of 1 Hz to 100 kHz, which ensures traceability to the International System of Units (SI). The flat phase noise signal is produced using a carrier combined with white noise. To ensure traceability, both the flat phase noise signal power and the power spectral density of white noise are determined with a calibrated power meter and the noise standard, respectively. The flatness of the phase noise standard is within ±0.7 dB.

  13. Noise in eukaryotic gene expression

    Science.gov (United States)

    Blake, William J.; KÆrn, Mads; Cantor, Charles R.; Collins, J. J.

    2003-04-01

    Transcription in eukaryotic cells has been described as quantal, with pulses of messenger RNA produced in a probabilistic manner. This description reflects the inherently stochastic nature of gene expression, known to be a major factor in the heterogeneous response of individual cells within a clonal population to an inducing stimulus. Here we show in Saccharomyces cerevisiae that stochasticity (noise) arising from transcription contributes significantly to the level of heterogeneity within a eukaryotic clonal population, in contrast to observations in prokaryotes, and that such noise can be modulated at the translational level. We use a stochastic model of transcription initiation specific to eukaryotes to show that pulsatile mRNA production, through reinitiation, is crucial for the dependence of noise on transcriptional efficiency, highlighting a key difference between eukaryotic and prokaryotic sources of noise. Furthermore, we explore the propagation of noise in a gene cascade network and demonstrate experimentally that increased noise in the transcription of a regulatory protein leads to increased cell-cell variability in the target gene output, resulting in prolonged bistable expression states. This result has implications for the role of noise in phenotypic variation and cellular differentiation.

  14. Pavement noise measurements in Poland

    Science.gov (United States)

    Zofka, Ewa; Zofka, Adam; Mechowski, Tomasz

    2017-09-01

    The objective of this study is to investigate the feasibility of the On-Board Sound Intensity (OBSI) system to measure tire-pavement noise in Poland. In general, sources of noise emitted by the modern vehicles are the propulsion noise, aerodynamic resistance and noise generated at the tire-pavement interface. In order to capture tire-pavement noise, the OBSI system uses a noise intensity probe installed in the close proximity of that interface. In this study, OBSI measurements were performed at different types of pavement surfaces such as stone mastic asphalt (SMA), regular asphalt concrete (HMA) as well as Portland cement concrete (PCC). The influence of several necessary OBSI measurement conditions were recognized as: testing speed, air temperature, tire pressure and tire type. The results of this study demonstrate that the OBSI system is a viable and robust tool that can be used for the quality evaluation of newly built asphalt pavements in Poland. It can be also applied to generate reliable input parameters for the noise propagation models that are used to assess the environmental impact of new and existing highway corridors.

  15. Airframe-Jet Engine Integration Noise

    Science.gov (United States)

    Tam, Christopher; Antcliff, Richard R. (Technical Monitor)

    2003-01-01

    It has been found experimentally that the noise radiated by a jet mounted under the wing of an aircraft exceeds that of the same jet in a stand-alone environment. The increase in noise is referred to as jet engine airframe integration noise. The objectives of the present investigation are, (1) To obtain a better understanding of the physical mechanisms responsible for jet engine airframe integration noise or installation noise. (2) To develop a prediction model for jet engine airframe integration noise. It is known that jet mixing noise consists of two principal components. They are the noise from the large turbulence structures of the jet flow and the noise from the fine scale turbulence. In this investigation, only the effect of jet engine airframe interaction on the fine scale turbulence noise of a jet is studied. The fine scale turbulence noise is the dominant noise component in the sideline direction. Thus we limit out consideration primarily to the sideline.

  16. Keeping Noise Down on the Farm

    Science.gov (United States)

    ... Do > Keeping Noise Down on the Farm Keeping Noise Down on the Farm SHARE Some people may ... risks permanent hearing damage. Take steps to reduce noise from machinery. Keep machinery running smoothly by replacing ...

  17. Noise-induced synchronization for phase turbulence

    OpenAIRE

    Sakaguchi, H.

    2003-01-01

    Phase turbulence is suppressed by applying common noise additively to the Kuramoto-Sivashinsky type equation, and the noise-induced phase synchronization is realized. The noise strength necessary for the suppression of phase turbulence is evaluated theoretically.

  18. The role of Urbis' noise and noise effects maps in local policy

    NARCIS (Netherlands)

    Borst, H.C.

    2001-01-01

    An important aspect of the EU noise policy is mapping of noise and noise effects and the formulation of noise action plans. In the Netherlands, due to the new policy on noise (MIG), the municipalities will be responsible for the formulation of a local noise policy. An instrument for the assessment o

  19. The Assessment of Noise Exposure and Noise Annoyance at a Petrochemical Company

    Directory of Open Access Journals (Sweden)

    S. Farhang Dehghan

    2013-12-01

    .Conclusion: Based on the obtained results of investigating the noise level (objective exposure as well as the noise annoyance (subjective exposure at the studied company, it is necessary to adopt the management –technical noise reduction measures at manufacturing sectors as the personal noise exposure and environmental noise exposure and also noise personal exposure of administrative staff can be decreased.

  20. Noise-induced hearing loss

    Directory of Open Access Journals (Sweden)

    Mariola Sliwinska-Kowalska

    2012-01-01

    Full Text Available Noise-induced hearing loss (NIHL still remains a problem in developed countries, despite reduced occupational noise exposure, strict standards for hearing protection and extensive public health awareness campaigns. Therefore NIHL continues to be the focus of noise research activities. This paper summarizes progress achieved recently in our knowledge of NIHL. It includes papers published between the years 2008-2011 (in English, which were identified by a literature search of accessible medical and other relevant databases. A substantial part of this research has been concerned with the risk of NIHL in the entertainment sector, particularly in professional, orchestral musicians. There are also constant concerns regarding noise exposure and hearing risk in "hard to control" occupations, such as farming and construction work. Although occupational noise has decreased since the early 1980s, the number of young people subject to social noise exposure has tripled. If the exposure limits from the Noise at Work Regulations are applied, discotheque music, rock concerts, as well as music from personal music players are associated with the risk of hearing loss in teenagers and young adults. Several recent research studies have increased the understanding of the pathomechanisms of acoustic trauma, the genetics of NIHL, as well as possible dietary and pharmacologic otoprotection in acoustic trauma. The results of these studies are very promising and offer grounds to expect that targeted therapies might help prevent the loss of sensory hair cells and protect the hearing of noise-exposed individuals. These studies emphasize the need to launch an improved noise exposure policy for hearing protection along with developing more efficient norms of NIHL risk assessment.

  1. Developing active noise control systems for noise attenuation in ducts

    Science.gov (United States)

    Campos, Rosely V.; Ivo, Rodrigo C.; Medeiros, Eduardo B.

    2002-11-01

    The present work describes some of the research effort on Active Noise Control (ANC) being jointly developed by the Catholic University of Minas Gerais (PUC-MINAS) and the Federal University of Minas Gerais (UFMG). Considerations about the implementation of Digital Signal Processing for noise control in ducts has been presented. The objective is to establish a study on Active Noise Control in ducts combining geometry and acoustic parameters modification together with adaptive digital filtering implementation. Both algorithm and digital signal processing details are also discussed. The main results for a typical application where real attenuation has been obtained are presented and considered according to their use in developing real applications. The authors also believe that the present text should provide an interesting overview for both designers and students concerned about Active Noise Control in ducts. (To be presented in Portuguese.)

  2. Entangled light from white noise

    CERN Document Server

    Plenio, M B

    2002-01-01

    An atom that couples to two distinct leaky optical cavities is driven by an external optical white noise field. We describe how entanglement between the light fields sustained by two optical cavities arises in such a situation. The entanglement is maximized for intermediate values of the cavity damping rates and the intensity of the white noise field, vanishing both for small and for large values of these parameters and thus exhibiting a stochastic-resonance-like behaviour. This example illustrates the possibility of generating entanglement by exclusively incoherent means and sheds new light on the constructive role noise may play in certain tasks of interest for quantum information processing.

  3. Entangled light from white noise.

    Science.gov (United States)

    Plenio, M B; Huelga, S F

    2002-05-13

    An atom that couples to two distinct leaky optical cavities is driven by an external optical white noise field. We describe how entanglement between the light fields sustained by two optical cavities arises in such a situation. The entanglement is maximized for intermediate values of the cavity damping rates and the intensity of the white noise field, vanishing both for small and for large values of these parameters and thus exhibiting a stochastic-resonancelike behavior. This example illustrates the possibility of generating entanglement by exclusively incoherent means and sheds new light on the constructive role noise may play in certain tasks of interest for quantum information processing.

  4. Substrate noise coupling in RFICs

    CERN Document Server

    Helmy, Ahmed

    2008-01-01

    Substrate Noise Coupling in RFICs addresses substrate noise coupling in RF and mixed signal ICs when used in a system on chip (SoC) containing digital ICs as well. This trend of integrating RF, mixed signal ICs with large digital ICs is found in many of today's commercial ICs such as single chip Wi-Fi or Bluetooth solutions and is expected to grow rapidly in the future. The book reports modeling and simulation techniques for substrate noise coupling effects in RFICs and introduces isolation structures and design guides to mitigate such effects with the ultimate goal of enhancing the yield of R

  5. Flow noise in sonar applications

    CERN Document Server

    Henke, Christian

    2016-01-01

    In this paper we present an investigation of flow noise in sonar applications. Based on a careful identification of the dominant coupling effects, the acoustic noise at the sensor position resulting from the turbulent wall pressure fluctuations is modelled with a system of hydrodynamic, bending and acoustic waves. We describe an analytical solution of the problem which is based on a coupled eigenfunction expansion method. Finally, it is demonstrated that the analytical solution describes the flow noise generation and propagation mechanisms of the considered sea trials.

  6. Efficient computational noise in GLSL

    CERN Document Server

    McEwan, Ian; Gustavson, Stefan; Richardson, Mark

    2012-01-01

    We present GLSL implementations of Perlin noise and Perlin simplex noise that run fast enough for practical consideration on current generation GPU hardware. The key benefits are that the functions are purely computational, i.e. they use neither textures nor lookup tables, and that they are implemented in GLSL version 1.20, which means they are compatible with all current GLSL-capable platforms, including OpenGL ES 2.0 and WebGL 1.0. Their performance is on par with previously presented GPU implementations of noise, they are very convenient to use, and they scale well with increasing parallelism in present and upcoming GPU architectures.

  7. Space noise synthetic aperture radar

    Science.gov (United States)

    Kulpa, Krzysztof S.

    2006-03-01

    The paper presents limitations of space borne synthetic aperture radars, caused by range and Doppler velocity ambiguities, and the concept of usage of the noise radar technology for creation of high-resolution space SAR images. The noise SAR is free from limitation caused by the periodicity of pulse waveform ambiguity function, and therefore this technology can be used in the future space missions. The basic concept of noise SAR image formation is also presented. The image formation algorithm has been verified using the simulated data produced by Raw Radar Data Simulator.

  8. Cosmological flux noise and measured noise power spectra in SQUIDs

    Science.gov (United States)

    Beck, Christian

    2016-06-01

    The understanding of the origin of 1/f magnetic flux noise commonly observed in superconducting devices such as SQUIDs and qubits is still a major unsolved puzzle. Here we discuss the possibility that a significant part of the observed low-frequency flux noise measured in these devices is ultimately seeded by cosmological fluctuations. We consider a theory where a primordial flux noise field left over in unchanged form from an early inflationary or quantum gravity epoch of the universe intrinsically influences the phase difference in SQUIDs and qubits. The perturbation seeds generated by this field can explain in a quantitatively correct way the form and amplitude of measured low-frequency flux noise spectra in SQUID devices if one takes as a source of fluctuations the primordial power spectrum of curvature fluctuations as measured by the Planck collaboration. Our theoretical predictions are in excellent agreement with recent low-frequency flux noise measurements of various experimental groups. Magnetic flux noise, so far mainly considered as a nuisance for electronic devices, may thus contain valuable information about fluctuation spectra in the very early universe.

  9. Noise suppression by quantum control before and after the noise

    Science.gov (United States)

    Wakamura, Hiroaki; Kawakubo, Ryûitirô; Koike, Tatsuhiko

    2017-02-01

    We discuss the possibility of protecting the state of a quantum system that goes through noise by measurements and operations before and after the noise process. The aim is to seek the optimal protocol that makes the input and output states as close as possible and to clarify the role of the measurements therein. We consider two cases: one can perform quantum measurements and operations (i) only after the noise process and (ii) both before and after. We prove in a two-dimensional Hilbert space that, in case (i), the noise suppression is essentially impossible for all types of noise and, in case (ii), the optimal protocol for the depolarizing noise is either the "do nothing" protocol or the "discriminate and reprepare" protocol. These protocols are not "truly quantum" and can be considered as classical. They involve no measurement or only use the measurement outcomes. These results describe the fundamental limitations in quantum mechanics from the viewpoint of control theory. Finally, we conjecture that a statement similar to case (ii) holds for higher-dimensional Hilbert spaces and present some numerical evidence.

  10. Seismometer Self-Noise and Measuring Methods

    Science.gov (United States)

    Ringler, Adam; R. Sleeman,; Hutt, Charles R.; Gee, Lind S.

    2014-01-01

    Seismometer self-noise is usually not considered when selecting and using seismic waveform data in scientific research as it is typically assumed that the self-noise is negligibly small compared to seismic signals. However, instrumental noise is part of the noise in any seismic record, and in particular, at frequencies below a few mHz, the instrumental noise has a frequency-dependent character and may dominate the noise. When seismic noise itself is considered as a carrier of information, as in seismic interferometry (e.g., Chaput et al. 2012), it becomes extremely important to estimate the contribution of instrumental noise to the recordings.

  11. Noise-Enabled Optical Ratchets

    CERN Document Server

    León-Montiel, Roberto de J

    2016-01-01

    In this work we demonstrate single microparticle transport enabled by noise in a one dimensional optical lattice with periodic symmetric potentials and a small constant external force. The one dimensional lattice is implemented by six focused beams with holographic optical tweezers, where a microparticle is trapped in three dimensions. Transport initiates when dynamical disorder is added to the diffracted laser power at each trap ($\\pm 30\\%$) at a fixed frequency (0 to 35 Hz), while the direction of motion is set by the constant external force. We find that transport is only achieved within a narrow noise frequency range, which is consistent with simulations, and the predicted behavior and observations of noise-induced energy transport in quantum and classical systems. To our knowledge this is the first direct observation of noise-assisted transport in a colloidal system.

  12. Assessment of Traffic Noise Impacts

    DEFF Research Database (Denmark)

    Rich, Jeppe Husted; Nielsen, Otto Anker

    2004-01-01

    A steady growth in traffic intensities in most urban areas throughout the world has forced planners and politicians to seriously consider the resulting environmental impact, such as traffic noise, accidents and air pollution. The assessment of such negative factors is needed in order to reveal...... the true social benefit of infrastructure plans. The paper presents a noise assessment model for the Copenhagen region, which brings together GIS technology and non-linear hedonic regression models to reveal the implicit costs of traffic noise measured as the marginal percentage loss in property values...... with respect to the decibel traffic noise. The model distinguishes between houses and apartments and shows that the ability to include refined accessibility variables have significant impact on estimated prices....

  13. RADIO NOISE ADVANCES SEXUAL MATURITY

    African Journals Online (AJOL)

    ansistf-lewis

    Supplementary radio noise advances sexual maturity in domestic pullets exposed .... non-stimulatory photoperiod in some way provides a stimulus for initiating rapid gonadal development. However, the ..... Congress, New Delhi, India. Vol II ...

  14. Noise Reduction in Car Speech

    OpenAIRE

    V. Bolom

    2009-01-01

    This paper presents properties of chosen multichannel algorithms for speech enhancement in a noisy environment. These methods are suitable for hands-free communication in a car cabin. Criteria for evaluation of these systems are also presented. The criteria consider both the level of noise suppression and the level of speech distortion. The performance of multichannel algorithms is investigated for a mixed model of speech signals and car noise and for real signals recorded in a car. 

  15. Anthropogenic noise changes arthropod abundances.

    Science.gov (United States)

    Bunkley, Jessie P; McClure, Christopher J W; Kawahara, Akito Y; Francis, Clinton D; Barber, Jesse R

    2017-05-01

    Anthropogenic noise is a widespread and growing form of sensory pollution associated with the expansion of human infrastructure. One specific source of constant and intense noise is that produced by compressors used for the extraction and transportation of natural gas. Terrestrial arthropods play a central role in many ecosystems, and given that numerous species rely upon airborne sounds and substrate-borne vibrations in their life histories, we predicted that increased background sound levels or the presence of compressor noise would influence their distributions. In the second largest natural gas field in the United States (San Juan Basin, New Mexico, USA), we assessed differences in the abundances of terrestrial arthropod families and community structure as a function of compressor noise and background sound level. Using pitfall traps, we simultaneously sampled five sites adjacent to well pads that possessed operating compressors, and five alternate, quieter well pad sites that lacked compressors, but were otherwise similar. We found a negative association between sites with compressor noise or higher levels of background sound and the abundance of five arthropod families and one genus, a positive relationship between loud sites and the abundance of one family, and no relationship between noise level or compressor presence and abundance for six families and two genera. Despite these changes, we found no evidence of community turnover as a function of background sound level or site type (compressor and noncompressor). Our results indicate that anthropogenic noise differentially affects the abundances of some arthropod families. These preliminary findings point to a need to determine the direct and indirect mechanisms driving these observed responses. Given the diverse and important ecological functions provided by arthropods, changes in abundances could have ecological implications. Therefore, we recommend the consideration of arthropods in the environmental

  16. Noise Reduction in Car Speech

    Directory of Open Access Journals (Sweden)

    V. Bolom

    2009-01-01

    Full Text Available This paper presents properties of chosen multichannel algorithms for speech enhancement in a noisy environment. These methods are suitable for hands-free communication in a car cabin. Criteria for evaluation of these systems are also presented. The criteria consider both the level of noise suppression and the level of speech distortion. The performance of multichannel algorithms is investigated for a mixed model of speech signals and car noise and for real signals recorded in a car. 

  17. Noise Tolerance under Risk Minimization

    CERN Document Server

    Manwani, Naresh

    2011-01-01

    In this paper we explore the problem of noise tolerant learning of classifiers. We formulate the problem as follows. We assume that there is an ${\\bf unobservable}$ training set which is noise-free. The actual training set given to the learning algorithm is obtained from this ideal data set by corrupting the class label of each example where the probability that the class label on an example is corrupted is a function of the feature vector of the example. This would account for almost all kinds of noisy data one may encounter in practice. We say that a learning method is noise tolerant if the classifiers learnt with the ideal noise-free data and with noisy data have the same classification accuracy on the noise-free data. In this paper we analyze the noise tolerant properties of risk minimization, which is a generic method for learning classifiers. We consider different loss functions such as 0-1 loss, hinge loss, exponential loss, squared error loss etc. We show that the risk minimization under 0-1 loss func...

  18. Noise annoys: effects of noise on breeding great tits depend on personality but not on noise characteristics

    NARCIS (Netherlands)

    Naguib, M.; Oers, van K.; Braakhuis, A.; Griffioen, M.; Goede, de P.; Waas, J.R.

    2013-01-01

    Anthropogenic noise can have serious implications for animals, especially when they communicate acoustically. Yet, the impacts of noise may depend not only on noise characteristics but also on an individual's coping style or personality. We tested whether noise is more disturbing if it masks communi

  19. The subjective importance of noise spectral content

    Science.gov (United States)

    Baxter, Donald; Phillips, Jonathan; Denman, Hugh

    2014-01-01

    This paper presents secondary Standard Quality Scale (SQS2) rankings in overall quality JNDs for a subjective analysis of the 3 axes of noise, amplitude, spectral content, and noise type, based on the ISO 20462 softcopy ruler protocol. For the initial pilot study, a Python noise simulation model was created to generate the matrix of noise masks for the softcopy ruler base images with different levels of noise, different low pass filter noise bandwidths and different band pass filter center frequencies, and 3 different types of noise: luma only, chroma only, and luma and chroma combined. Based on the lessons learned, the full subjective experiment, involving 27 observers from Google, NVIDIA and STMicroelectronics was modified to incorporate a wider set of base image scenes, and the removal of band pass filtered noise masks to ease observer fatigue. Good correlation was observed with the Aptina subjective noise study. The absence of tone mapping in the noise simulation model visibly reduced the contrast at high levels of noise, due to the clipping of the high levels of noise near black and white. Under the 34-inch viewing distance, no significant difference was found between the luma only noise masks and the combined luma and chroma noise masks. This was not the intuitive expectation. Two of the base images with large uniform areas, `restaurant' and `no parking', were found to be consistently more sensitive to noise than the texture rich scenes. Two key conclusions are (1) there are fundamentally different sensitivities to noise on a flat patch versus noise in real images and (2) magnification of an image accentuates visual noise in a way that is non-representative of typical noise reduction algorithms generating the same output frequency. Analysis of our experimental noise masks applied to a synthetic Macbeth ColorChecker Chart confirmed the color-dependent nature of the visibility of luma and chroma noise.

  20. Noise in the Library: Effects and Control.

    Science.gov (United States)

    Eagan, Ann

    1991-01-01

    Describes the physiological and psychological effects of noise in libraries and suggests methods of controlling noise from telephones, computers, printers, and photocopiers. Hearing loss and stress-related problems are discussed, the effects of noise on performance are described, and planning is emphasized as a method of avoiding noise problems.…

  1. An adaptive algorithm for noise rejection.

    Science.gov (United States)

    Lovelace, D E; Knoebel, S B

    1978-01-01

    An adaptive algorithm for the rejection of noise artifact in 24-hour ambulatory electrocardiographic recordings is described. The algorithm is based on increased amplitude distortion or increased frequency of fluctuations associated with an episode of noise artifact. The results of application of the noise rejection algorithm on a high noise population of test tapes are discussed.

  2. Numerical simulation of tyre/road noise

    NARCIS (Netherlands)

    Schutte, Jan Henk

    2011-01-01

    In modern society, traffic noise has become an important issue for mental health. A significant contributor to this noise pollution is exterior tyre/road noise, which is caused by the interaction between tyre and road surface and. In order to reduce tyre/road noise at the source, accurate numerical

  3. 32 CFR 989.32 - Noise.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Noise. 989.32 Section 989.32 National Defense... ANALYSIS PROCESS (EIAP) § 989.32 Noise. Aircraft noise data files used for analysis during EIAP will be... System for Aircraft Noise for military training routes and military operating areas. Guidance...

  4. Radiation characteristics of intermittence exhaust noise

    Institute of Scientific and Technical Information of China (English)

    ZHAO Shengdun; SHANG Chunyang; ZHAO Zhigang; SHI Weixiang

    2000-01-01

    Aerodynamic characteristics, the noise characteristics in the course of intermittence exhaust are investigated and the expressions for sound pressure level of the noise generated by single-pole source and quadrupole source in the intermittence exhaust noise are established. The effects of all parameters in pneumatic system on the noise are also comprehensively studied.

  5. Aircraft Noise Prediction Program theoretical manual: Propeller aerodynamics and noise

    Science.gov (United States)

    Zorumski, W. E. (Editor); Weir, D. S. (Editor)

    1986-01-01

    The prediction sequence used in the aircraft noise prediction program (ANOPP) is described. The elements of the sequence are called program modules. The first group of modules analyzes the propeller geometry, the aerodynamics, including both potential and boundary-layer flow, the propeller performance, and the surface loading distribution. This group of modules is based entirely on aerodynamic strip theory. The next group of modules deals with the first group. Predictions of periodic thickness and loading noise are determined with time-domain methods. Broadband noise is predicted by a semiempirical method. Near-field predictions of fuselage surface pressrues include the effects of boundary layer refraction and scattering. Far-field predictions include atmospheric and ground effects.

  6. IMPROVED MLV FILTER TO REMOVE MULTIPLICATIVE NOISE

    Institute of Scientific and Technical Information of China (English)

    Li Weibin; Liu Fang; Jiao Licheng; Zhang Shuling; Li Zongling

    2006-01-01

    More methods can be used to remove the additive noise, such as the Mean of Least Variance (MLV)filter. When the signal is noised by the multiplicative noise, it is difficult to remove. The paper presents an improved filter to remove multiplicative noise by changing the multiplicative noise to the additive noise, and then using the MLV-like to remove the additive noise. The simulation results show that the performance is better than Minimum Coefficient of Variation (MCV) filter and MLV filter. Both one-dimension and image experiments demonstrate its theoretical performance.

  7. Implementasi Metode Kombinasi Mean Filter Dan Median Filter Untuk Mereduksi Gaussian Noise, Salt And Pepper Noise, Speckle Noise, Dan Exponential Noise Pada Citra Digital

    OpenAIRE

    Fadillah, Azhar

    2014-01-01

    Nowadays, the use of image as form of information is currently increasing. Poor quality of image can reduce its information contained in image. For example, the image contains noise so the information that contained in the image are not clear. Noise on the digital image can be either Gaussian noise, Salt and Pepper Noise, Speckle Noise, and Exponential Noise. One of the mechanisms used to reduce the noise is filtering. Mean Filter method and Median Filter method are a very good method to redu...

  8. Ambient noise near the sea-route

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Ambient noise data measured in an experiment conducted in shallow water near a sea-route were analyzed. It was observed that, at low frequency, the horizontal correlation has an obvious difference from that predicted by the classical ambient noise model. The theoretical analyses show that this phenomenon is caused by wind noise together with the discrete shipping noise nearby. An ambient noise model was proposed to include the effects caused by both the noise sources. Data measured at different times verify that the proposed model can be used to forecast the ambient noise field in shallow water near the sea-route.

  9. Ambient noise near the sea-route

    Institute of Scientific and Technical Information of China (English)

    HE Li; LI ZhengLin; PENG ZhaoHui

    2009-01-01

    Ambient noise data measured in an experiment conducted in shallow water near a sea-route were analyzed. It was observed that, at low frequency, the horizontal correlation has an obvious difference from that predicted by the classical ambient noise model. The theoretical analyses show that this phenomenon is caused by wind noise together with the discrete shipping noise nearby. An ambient noise model was proposed to include the effects caused by both the noise sources. Data measured at different times verify that the proposed model can be used to forecast the ambient noise field in shal-low water near the sea-route.

  10. 虚拟车内噪声响度场分布的声源识别分析与优化%Virtual loudness mapping for noise source identification and optimization design for vehicle interior noise reduction

    Institute of Scientific and Technical Information of China (English)

    高印寒; 张澧桐; 梁杰; 王智博; 姜文君

    2016-01-01

    The shortcomings of traditional sound pressures level (SPL)were discussed,such as the lack of subjectivity consideration for noise and so on.A virtual method for predicting loudness characteristics and identifying noise sources based on human auditory properties was applied to analyze vehicle interior noises.In order to reduce the interior low booming of commercial vehicle,a characteristic loudness calculation model for diffuse sound field was built in Matlab on the basis of Zwicker model.The excitation signals at the suspension mountings and the responding signals of the interior noise were measured by road testing.And to predict and calculate the loudness mapping and structural contribution of the cab,an acoustic-structure coupled finite element model was established,by which the influences of the vehicle interior noise from different plates sources on the sound quality frequency spectrum design were analysed.The results of noise source identification reveal that compared with the traditional SPL,the loudness mapping adopted as an identifying parameter in noise source identification is more effective to detect rattling sources from cab plates vibrations.By using the proposed method,the acoustic optimization design of the cab was carried out and results in excellent performances.%针对传统声压级对车内噪声主观性考虑不足的缺陷,提出符合人双耳特性的虚拟车内噪声特征响度预测及声源识别方法。根据某重型商用车驾驶室内低频轰鸣声严重的问题,基于 Zwicker 响度模型,在 matlab 中建立频域的混响场特征响度计算模型。结合路试实验激励数据和驾驶室有限元声-固耦合模型,对驾驶室内噪声响度分布和响度结构板块贡献量进行计算,识别不同板材振动产生的辐射噪声分量对驾驶室内噪声品质频谱特性的影响。实验结果表明:相对于声压级,采用响度作为分析参数提高了驾驶室内噪声源识别精度,

  11. Noise induced intercellular propagation of calcium waves

    Science.gov (United States)

    Nchange, A. K.; Kepseu, W. D.; Woafo, P.

    2008-04-01

    In this paper, we investigate the spatiotemporal dynamics of a bidirectional coupled chain of cells, in which a cell is subjected to an external noise. Noisy oscillations of calcium (Ca 2+), that is, a bursting-like phenomenon induced by noise with fluctuations in the baseline values of calcium, are induced in the first cell and propagated along the chain with noise suppression. This phenomenon of noise suppression is further investigated by computing the normalized fluctuation of pulse durations. It is therefore found that the noise induced coherence resonance phenomenon occurs at the cellular level. Coherence biresonance behaviour appears in the transmission of noise induced oscillations at appropriate noise intensity or noise coupling (for low noise intensity) and the information flow in each cell can be simultaneously optimized at the optimal value of noise or coupling.

  12. Health Effects of Noise Exposure in Children.

    Science.gov (United States)

    Stansfeld, Stephen; Clark, Charlotte

    2015-06-01

    Environmental noise exposure, such as road traffic noise and aircraft noise, is associated with a range of health outcomes in children. Children demonstrate annoyance responses to noise, and noise is also related to lower well-being and stress responses, such as increased levels of adrenaline and noradrenaline. Noise does not cause more serious mental health problems, but there is growing evidence for an association with increased hyperactivity symptoms. Studies also suggest that noise might cause changes in cardiovascular functioning, and there is some limited evidence for an effect on low birth weight. There is robust evidence for an effect of school noise exposure on children's cognitive skills such as reading and memory, as well as on standardised academic test scores. Environmental noise does not usually reach levels that are likely to affect children's hearing; however, increasing use of personal electronic devices may leave some children exposed to harmful levels of noise.

  13. Vienna international airport noise abatement

    Directory of Open Access Journals (Sweden)

    Heidelinde Jelinek-Nigitz

    2016-03-01

    Full Text Available Purpose: On the topic of sustainable aviation a study was carried out to measure the difference between the actual change in air traffic noise and the airport’s residents’ perception of the noise change at Vienna International Airport. Therefore, a questionnaire was developed in cooperation with the airport and an online survey was conducted. Design/methodology/approach: For the survey of the opinion of the affected population of the surrounding communities, a web based online questionnaire is created and distributed via various channels including e-mail, and online forums. After the basic structure of the questionnaire had been defined, the questions were developed in cooperation with employees form the environmental department of VIE, who had a sustainable influence on the questions’ order and formulation. As the survey was supposed to be answered by residents around VIE. Findings: Results of the online study show that only parts of the participants are affected by air traffic noise at VIE. Even less experienced a significant change over the last five years. About one third of the participants stated that they are affected by air traffic noise in one way or another. The majority of these people live in Lower Austria, the federal state in which the airport is located. The participants obviously judge air traffic noise during day time more importantly than air traffic noise at night. Research limitations/implications: Due to the low number of returns, no statistically relevant conclusions can be drawn, the results of the survey can be used to make some general statements. Originality/value: Economic growth and deregulation lead to growing aircraft operations. Vienna International Airport with its approximately 260,000 flight movements per year is the biggest airport in Austria and a major hub in Europe. The combination of constantly growing air transport and the resulting noise exposure, as well as the steadily increasing

  14. Aero-acoustic noise of wind turbines. Noise prediction models

    Energy Technology Data Exchange (ETDEWEB)

    Maribo Pedersen, B. [ed.

    1997-12-31

    Semi-empirical and CAA (Computational AeroAcoustics) noise prediction techniques are the subject of this expert meeting. The meeting presents and discusses models and methods. The meeting may provide answers to the following questions: What Noise sources are the most important? How are the sources best modeled? What needs to be done to do better predictions? Does it boil down to correct prediction of the unsteady aerodynamics around the rotor? Or is the difficult part to convert the aerodynamics into acoustics? (LN)

  15. Noise Exclusion Ability in Infants

    Directory of Open Access Journals (Sweden)

    Geroldene Tsui

    2011-05-01

    Full Text Available An important perceptual ability is to filter out background distractions from relevant information. However, prior research has not identified when this begins in humans. Our study aims to investigate whether noise exclusion ability occurs in infancy. Infants' contrast sensitivity function (CSF was measured by a Baynesian adaptive inference method. Infants' attention was directed to the middle of a monitor where an 8.72 degree static Gabor grating was presented on the left or right side of the monitor. In half the trials, the grating was presented against a gray background; in the other half, against a 16% contrast random-dot noise background. The experimenter and two independent coders judged which side the infants gazed at (force-choice preferential looking paradigm. One-hundred babies aged from 4 to 10 months satisfied the 70% interrater consistency criterion for inclusion. Four parameters defined the best-fitted CSF for each infant. Of these, peak spatial frequency, bandwidth and truncation of CSF were similar in conditions with and without noise. The peak gain estimate was most significantly impaired by external noise, but a marked 31% improvement was observed in 7- to 10-month-olds. This may be the first sign of development of human's noise exclusion ability, and is worth further study.

  16. Modularity, noise, and natural selection.

    Science.gov (United States)

    Marroig, Gabriel; Melo, Diogo A R; Garcia, Guilherme

    2012-05-01

    Most biological systems are formed by component parts that are to some degree interrelated. Groups of parts that are more associated among themselves and are relatively autonomous from others are called modules. One of the consequences of modularity is that biological systems usually present an unequal distribution of the genetic variation among traits. Estimating the covariance matrix that describes these systems is a difficult problem due to a number of factors such as poor sample sizes and measurement errors. We show that this problem will be exacerbated whenever matrix inversion is required, as in directional selection reconstruction analysis. We explore the consequences of varying degrees of modularity and signal-to-noise ratio on selection reconstruction. We then present and test the efficiency of available methods for controlling noise in matrix estimates. In our simulations, controlling matrices for noise vastly improves the reconstruction of selection gradients. We also perform an analysis of selection gradients reconstruction over a New World Monkeys skull database to illustrate the impact of noise on such analyses. Noise-controlled estimates render far more plausible interpretations that are in full agreement with previous results. © 2012 The Author(s). Evolution© 2012 The Society for the Study of Evolution.

  17. Combined sensor noise-immunity

    Institute of Scientific and Technical Information of China (English)

    Vladimir A. Shchurov; Alexander V. Shchurov

    2002-01-01

    The paper presents statistical analysis of combined sensor noise-immunity while recording fluctuating tone against underwater dynamic noise background. The experimental data used for the analysis have been collected by a pair of four-component combined sensors centered at two depths, 150 and 300 m in deep water. Expressions for combined sensor signalto-noise ratio (SNR) for cross-spectral levels of signal and noise for both wide and narrow frequency bands have been derived. A combined sensor gain has been introduced in terms of ordinary single-point coherence function between acoustic pressure and particle velocity in acoustic wave. The estimates obtained experimentally evidence that SNR for a combined sensor with multiplicative data processing may exceed SNR for a hydrophone-based sensor by 15 to 16 dB at most for the horizontal channel of the combined sensor, and by 30 dB at most for the vertical channel (when opposite energy flows of signal and noise compensate one another).

  18. Noise exposure under hyperbaric conditions

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Objective evidence exists that divers demonstrate a hearing deficit greater than would be expected from ageing effects alone. Deafness in divers may be caused by a number of factors other than exposure to excessive noise levels, eg barotrauma, ear infection etc. This review concentrates on the concern that exposure of commercial divers to noise while at work may cause a hearing deficit. Sound pressure levels recorded both underwater and in diving chambers often exceed those allowable to workers onshore. However, the sound perceived by the diver is modified both in amplitude and in frequency when he is either underwater or in pressurised chambers. Broadly the effect of this modification is to attenuate the sound and thus offer some protection from high noise levels. The degree of attentuation varies with the frequency of the sound, however it is also possible under specific conditions associated with gas density for the sensitivity to particular frequencies to be amplified above that for normal atmospheric air. The levels of sound observed from some underwater tools are of concern even after allowing for a significant de-sensitisation of the divers` hearing. Reports of tinnitus and temporary hearing loss following a dive are sure signs that the noise levels have been harmful. It is not possible at present to describe risk criteria for hearing damage due to noise exposure associated with diving. (author)

  19. Noise in Class AB translinear filter

    Energy Technology Data Exchange (ETDEWEB)

    Martini, G.; Svelto, V. [Pavia Univ. (Italy). Dip di Elettronica

    1998-07-01

    A specific statistical approach to describe the noise properties of non linear circuits is used. The noise properties of translinear filters operated in class AB are considered. This kind of filter has a dynamic range larger then the maximum signal to noise ratio, and exhibit signal to noise ratio saturation at high signal level. The paper shows how the noise properties depend on the circuit design parameters.

  20. Noise in space. [effect on Skylab astronauts

    Science.gov (United States)

    Rader, W. P.; Baratono, J.; Bandgren, H.; Erwin, R.

    1975-01-01

    The Skylab program presented an excellent opportunity to investigate the effects of noise on man confined in limited space for long periods of time. This paper summarizes the results of a 4-year study to achieve a habitable noise environment for the Skylab astronauts. Noise control measures are described and noise measurements obtained during the Skylab missions are presented, as well as the astronauts' reactions to and evaluations of the noise environment.

  1. A New Phase Noise Detection Method

    OpenAIRE

    Yan, Gangfeng

    2015-01-01

    Phase noise is one of the most important parameters in many oscillators. Detecting accurately phase noise for oscillators has importance significance. In this paper, based on correlation operation detection phase noise for oscillators was proposed. This method not only can save a high precision reference oscillator, but also can detect accurately the phase noise of measured oscillator in theory. Detected phase noise of oscillators using this method has very strong utility value.

  2. Uncorrelated Noise in Turbulence Measurements

    DEFF Research Database (Denmark)

    Kristensen, Leif; Lenschow, D. H.

    1985-01-01

    effect is smeared across the entire power spectrum. For this reason, quantities such as variance dissipation may be more conveniently estimated from the structure function than from the spectrum. The modeling results are confirmed by artificially modifying a test time series with Poisson noise......We show that the error variance contributed by random uncorrelated measurement noise can be merged with the error variance contributed by real variation in the atmosphere to obtain a single expression for the total error variance when the sampling time is much less than the integral scale...... of atmospheric variability. The authors assume that the measured signal is a representation of a variable that is continuous on the scale of interest in the atmosphere. Uncorrelated noise affects the autovariance function (or, equivalently, the structure function) only between zero and the first lag, while its...

  3. Stochastic noise in splicing machinery

    OpenAIRE

    Melamud, Eugene; Moult, John

    2009-01-01

    The number of known alternative human isoforms has been increasing steadily with the amount of available transcription data. To date, over 100 000 isoforms have been detected in EST libraries, and at least 75% of human genes have at least one alternative isoform. In this paper, we propose that most alternative splicing events are the result of noise in the splicing process. We show that the number of isoforms and their abundance can be predicted by a simple stochastic noise model that takes i...

  4. Detection of signals in noise

    CERN Document Server

    Whalen, Anthony D; Declaris, Nicholas

    1971-01-01

    Detection of Signals in Noise serves as an introduction to the principles and applications of the statistical theory of signal detection. The book discusses probability and random processes; narrowband signals, their complex representation, and their properties described with the aid of the Hilbert transform; and Gaussian-derived processes. The text also describes the application of hypothesis testing for the detection of signals and the fundamentals required for statistical detection of signals in noise. Problem exercises, references, and a supplementary bibliography are included after each c

  5. Removing Noise From Pyrosequenced Amplicons

    Directory of Open Access Journals (Sweden)

    Davenport Russell J

    2011-01-01

    Full Text Available Abstract Background In many environmental genomics applications a homologous region of DNA from a diverse sample is first amplified by PCR and then sequenced. The next generation sequencing technology, 454 pyrosequencing, has allowed much larger read numbers from PCR amplicons than ever before. This has revolutionised the study of microbial diversity as it is now possible to sequence a substantial fraction of the 16S rRNA genes in a community. However, there is a growing realisation that because of the large read numbers and the lack of consensus sequences it is vital to distinguish noise from true sequence diversity in this data. Otherwise this leads to inflated estimates of the number of types or operational taxonomic units (OTUs present. Three sources of error are important: sequencing error, PCR single base substitutions and PCR chimeras. We present AmpliconNoise, a development of the PyroNoise algorithm that is capable of separately removing 454 sequencing errors and PCR single base errors. We also introduce a novel chimera removal program, Perseus, that exploits the sequence abundances associated with pyrosequencing data. We use data sets where samples of known diversity have been amplified and sequenced to quantify the effect of each of the sources of error on OTU inflation and to validate these algorithms. Results AmpliconNoise outperforms alternative algorithms substantially reducing per base error rates for both the GS FLX and latest Titanium protocol. All three sources of error lead to inflation of diversity estimates. In particular, chimera formation has a hitherto unrealised importance which varies according to amplification protocol. We show that AmpliconNoise allows accurate estimates of OTU number. Just as importantly AmpliconNoise generates the right OTUs even at low sequence differences. We demonstrate that Perseus has very high sensitivity, able to find 99% of chimeras, which is critical when these are present at high

  6. The Hannover thermal noise experiment

    Energy Technology Data Exchange (ETDEWEB)

    Leonhardt, V; Ribichini, L; Lueck, H; Danzmann, K [Max-Planck-Institute for Gravitational Physics (Albert-Einstein-Institute) and University of Hannover, Callinstr. 38, D-30167 Hannover (Germany)

    2004-03-07

    To analyse the thermal noise of the pendulum mode of a suspended mirror, we interferometrically detect the differential movement of two mirrors suspended as multiple-stage pendulums. We present the set-up of this experiment and the current sensitivity, and also the different steps that we took in the past to increase the sensitivity, which include an auto alignment of the laser beam into the resonator eigenmode, changes of the seismic isolation system to more damping stages and higher moments of inertia and an intensive noise hunting.

  7. Is freight traffic noise more annoying than passenger traffic noise?

    NARCIS (Netherlands)

    Jong, R.G. de; Miedema, H.M.E.

    1996-01-01

    In the Netherlands a new freight-only railway route, the "Betuweroute", is being planned to carry freight traffic from Rotterdam harbour east into Germany. Inhabitants of areas near the future route are concerned about noise and vibration, and question the relevance of current legislation for a

  8. Relationship between exposure to multiple noise sources and noise annoyance

    NARCIS (Netherlands)

    Miedema, H.M.E.

    2004-01-01

    Relationships between exposure to noise [metric: day-night level (DNL) or day-evening-night level (DENL)] from a single source (aircraft, road traffic, or railways) and annoyance based on a large international dataset have been published earlier. Also for stationary sources relationships have been

  9. The Problems with "Noise Numbers" for Wind Farm Noise Assessment

    Science.gov (United States)

    Thorne, Bob

    2011-01-01

    Human perception responds primarily to sound character rather than sound level. Wind farms are unique sound sources and exhibit special audible and inaudible characteristics that can be described as modulating sound or as a tonal complex. Wind farm compliance measures based on a specified noise number alone will fail to address problems with noise…

  10. Distributed fusion white noise deconvolution estimators

    Institute of Scientific and Technical Information of China (English)

    Xiaojun SUN; Zili DENG

    2009-01-01

    The white noise deconvolution or input white noise estimation problem has important applications in oil seismic exploration, communication and signal processing.By combining the Kalman filtering method with the modern time series analysis method, based on the autoregressive moving average (ARMA) innovation model, new distributed fusion white noise deconvolution estimators are presented by weighting local input white noise estimators for general multisensor systems with different local dynamic models and correlated noises. The new estimators can handle input white noise fused filtering,prediction and smoothing problems, and are applicable to systems with colored measurement noise. Their accuracy is higher than that of local white noise deconvolution estimators. To compute the optimal weights, the new formula for local estimation error cross-covariances is given. A Monte Carlo simulation for the system with Bemoulli-Gaussian input white noise shows their effec-tiveness and performance.

  11. Noise in a CMOS digital pixel sensor

    Institute of Scientific and Technical Information of China (English)

    Zhang Chi; Yao Suying; Xu Jiangtao

    2011-01-01

    Based on the study of noise performance in CMOS digital pixel sensor (DPS),a mathematical model of noise is established with the pulse-width-modulation (PWM) principle.Compared with traditional CMOS image sensors,the integration time is different and A/D conversion is implemented in each PWM DPS pixel.Then,the quantitative calculating formula of system noise is derived.It is found that dark current shot noise is the dominant noise source in low light region while photodiode shot noise becomes significantly important in the bright region.In this model,photodiode shot noise does not vary with luminance,but dark current shot noise does.According to increasing photodiode capacitance and the comparator's reference voltage or optimizing the mismatch in the comparator,the total noise can be reduced.These results serve as a guideline for the design of PWM DPS.

  12. Noise mapping inside a car cabin

    DEFF Research Database (Denmark)

    Knudsen, Kim; Sjøj, Sidsel Marie Nørholm; Jacobsen, Finn

    The mapping of noise is of considerable interest in the car industry where a good noise mapping can make it much easier to identify the sources that generate the noise and eventually reduce the individual contributions to the noise. The methods used for this purpose include delay-and-sum beamform......The mapping of noise is of considerable interest in the car industry where a good noise mapping can make it much easier to identify the sources that generate the noise and eventually reduce the individual contributions to the noise. The methods used for this purpose include delay......-and-sum beamforming and spherical harmonics beamforming. These methods have a poor spatial esolution at low frequencies, and since much noise generated in cars is dominated by low frequencies the methods are not optimal. In the present paper the mapping is done by solving an inverse problem with a transfer matrix...

  13. Background noise spectra of global seismic stations

    Energy Technology Data Exchange (ETDEWEB)

    Wada, M.M.; Claassen, J.P.

    1996-08-01

    Over an extended period of time station noise spectra were collected from various sources for use in estimating the detection and location performance of global networks of seismic stations. As the database of noise spectra enlarged and duplicate entries became available, an effort was mounted to more carefully select station noise spectra while discarding others. This report discusses the methodology and criteria by which the noise spectra were selected. It also identifies and illustrates the station noise spectra which survived the selection process and which currently contribute to the modeling efforts. The resulting catalog of noise statistics not only benefits those who model network performance but also those who wish to select stations on the basis of their noise level as may occur in designing networks or in selecting seismological data for analysis on the basis of station noise level. In view of the various ways by which station noise were estimated by the different contributors, it is advisable that future efforts which predict network performance have available station noise data and spectral estimation methods which are compatible with the statistics underlying seismic noise. This appropriately requires (1) averaging noise over seasonal and/or diurnal cycles, (2) averaging noise over time intervals comparable to those employed by actual detectors, and (3) using logarithmic measures of the noise.

  14. Optimum deconvolution algorithm for system with multiplicative white noise and additive correlative noise

    Institute of Scientific and Technical Information of China (English)

    王会立; 陈希信

    2004-01-01

    The optimum state filter and fixed-interval smoother and the optimum deconvolution algorithm for system with multiplicative noise are derived upon the condition that the dynamic noise correlates itself in one-step and correlates with the measurement noise at the present step as well as one past step, and the multiplicative noise is white and statistically independent of the dynamic noise and the measurement noise. A simulation example demonstrates the effectiveness of the above-mentioned deconvolution algorithm.

  15. Radiated noise of ducted fans

    Science.gov (United States)

    Eversman, Walter

    The differences in the radiated acoustic fields of ducted and unducted propellers of the same thrust operating under similar conditions are investigated. An FEM model is created for the generation, propagation, and radiation of steady, rotor alone noise and exit guide vane interaction noise of a ducted fan. For a specified number of blades, angular mode harmonic, and rotor angular velocity, the acoustic field is described in a cylindrical coordinate system reduced to only the axial and radial directions. It is found that, contrary to the usual understanding of the Tyler and Sofrin (1962) result, supersonic tip speed rotor noise can be cut off if the tip Mach number is only slightly in excess of unity and if the number of blades is relatively small. If there are many blades, the fundamental angular mode number is large, and the Tyler and Sofrin result for thin annuli becomes more relevant. Shrouding of subsonic tip speed propellers is a very effective means of controlling rotor alone noise.

  16. Physically Damped Noise Canceling Hydrophone

    Science.gov (United States)

    2016-06-24

    300075 1 of 10 PHYSICALLY DAMPED NOISE CANCELING HYDROPHONE STATEMENT OF GOVERNMENT INTEREST [0001] The invention described herein may be...transducer with an electromechanical driver comprising a plurality of single crystal piezoelectric elements joined to an inner surface and arranged to form...an electromechanical stack assembly. Each single crystal piezoelectric element has a surface, an opposite surface, and a Attorney Docket No

  17. Underwater noise due to precipitation

    DEFF Research Database (Denmark)

    Crum, Lawrence A.; Pumphrey, Hugh C.; Prosperetti, Andrea;

    1989-01-01

    surface, both for individual and for multiple events such as those produced by artificial and natural rainfall, has been examined. The studies indicate that the major contribution to the underwater noise produced by both rain and snow is that associated with the oscillations of gas bubbles introduced...

  18. Noise Considerations in Resistance Bridges

    DEFF Research Database (Denmark)

    Diamond, Joseph M.

    1963-01-01

    A signal-to-noise analysis is made of the Wheatstone bridge, where the unknown and standard resistors may be at different temperatures, a situation which occurs in resistance thermometry. The limiting condition is assumed to be dissipation in the unknown resistor. It is shown that the ratio arms ...

  19. A Low Noise Electronic Circuit

    NARCIS (Netherlands)

    Annema, Anne J.; Leenaerts, Dominicus M.W.; de Vreede, Petrus W.H.

    2002-01-01

    An electronic circuit, which can be used as a Low Noise Amplifier (LNA), comprises two complementary Field Effect Transistors (M1, M2; M5, M6), each having a gate, a source and a drain. The gates are connected together as a common input terminal, and the drains are connected together as a

  20. Ground Attenuation of Railroad Noise

    DEFF Research Database (Denmark)

    Makarewicz, R.; Rasmussen, Karsten Bo; Kokowski, P.

    1996-01-01

    The influence of ground effect on railroad noise is described using the concept of the peak A-weighted sound exposure level, and A-weighted sound exposure level. The train is modelled by a continuous line of incoherent point sources that have a cosine directivity. The ground effect is included by...

  1. Introduction: Unsolved Problems on Noise

    Science.gov (United States)

    Oriols, X.; Ciliberto, S.

    2016-05-01

    This paper is an introduction to the special issue of the 7th Int. Conf. on Unsolved Problems on Noise (UPoN) that took place at Casa Convalescència in Barcelona (Spain) in July 2015. The aim of the UPoN conferences is to provide a forum for researchers working on different fields of noise, fluctuations and variability, where they present their scientific problems which resist solutions. The papers of this Special Issue reflect the interdisciplinary topics (physics, biology, circuits, financial markets, psychology, technology, etc) presented at the UPoN conference. Noise is not only a hindrance to signal detection, but it is indeed a valuable source of information (not present in the signal) that help us to get a deeper understanding on how Nature works. This special issue of the 7th International Conference on Unsolved Problems on Noise (UPoN) is dedicated to Laszlo Kish in the occasion of his 60th birthday. He organized the first edition of these UPoN conferences in Szeged (Hungary) in 1996. Many of us have greatly benefited from his ‘volcanic imagination in tackling new problems from unconventional points of views’.

  2. Noise Properties of Rectifying Nanopores

    Energy Technology Data Exchange (ETDEWEB)

    Powell, M R; Sa, N; Davenport, M; Healy, K; Vlassiouk, I; Letant, S E; Baker, L A; Siwy, Z S

    2011-02-18

    Ion currents through three types of rectifying nanoporous structures are studied and compared for the first time: conically shaped polymer nanopores, glass nanopipettes, and silicon nitride nanopores. Time signals of ion currents are analyzed by power spectrum. We focus on the low-frequency range where the power spectrum magnitude scales with frequency, f, as 1/f. Glass nanopipettes and polymer nanopores exhibit non-equilibrium 1/f noise, thus the normalized power spectrum depends on the voltage polarity and magnitude. In contrast, 1/f noise in rectifying silicon nitride nanopores is of equilibrium character. Various mechanisms underlying the voltage-dependent 1/f noise are explored and discussed, including intrinsic pore wall dynamics, and formation of vortices and non-linear flow patterns in the pore. Experimental data are supported by modeling of ion currents based on the coupled Poisson-Nernst-Planck and Navier Stokes equations. We conclude that the voltage-dependent 1/f noise observed in polymer and glass asymmetric nanopores might result from high and asymmetric electric fields inducing secondary effects in the pore such as enhanced water dissociation.

  3. Instantaneous noise-based logic

    CERN Document Server

    Kish, Laszlo B; Peper, Ferdinand

    2010-01-01

    We show two universal, Boolean, deterministic logic schemes based on binary noise timefunctions that can be realized without time averaging units. The first scheme is based on a new bipolar random telegraph wave scheme and the second one makes use of the recent noise-based logic which is conjectured to be the brain's method of logic operations [Physics Letters A 373 (2009) 2338-2342, arXiv:0902.2033]. For binary-valued logic operations, the two simple Boolean schemes presented in this paper use zero (no noise) for the logic Low (L) state. In the random telegraph wave-based scheme, for multi-valued logic operations, additive superpositions of logic states must be avoided, while multiplicative superpositions utilizing hyperspace base vectors can still be utilized. These modifications, while keeping the information richness of multi-valued (noise-based) logic, result in a significant speedup of logic operations for the same signal bandwidth. The logic hyperspace of the first scheme results random telegraph waves...

  4. Hydrodynamic Noise and Surface Compliance.

    Science.gov (United States)

    1982-09-08

    Lighthill, 3,4 Ffowcs-Wiiliams, 5-7 and Morse and Ingard .8 Ffowcs-Williams’ 7 excellent review identifies five distinctly different theoretical...Williams, "Hydrodynamic Noise," Annual Review of Fluid Mechanics (Annual Reviews, Palo Alto, CA), vol. 1, 1969, pp. 197-222. 8. P. Morse and K. V. Ingard

  5. Shot noise in radiobiological systems.

    Science.gov (United States)

    Datesman, A

    2016-11-01

    As a model for human tissue, this report considers the rate of free radical generation in a dilute solution of water in which a beta-emitting radionuclide is uniformly dispersed. Each decay dissipates a discrete quantity of energy, creating a large number of free radicals in a short time within a small volume determined by the beta particle range. Representing the instantaneous dissipated power as a train of randomly-spaced pulses, the time-averaged dissipated power p¯ and rate of free radical generation g¯ are derived. The analogous result in the theory of electrical circuits is known as the shot noise theorem. The reference dose of X-rays Dref producing an identical rate of free radical generation and level of oxidative stress is shown a) to increase with the square root of the absorbed dose, D, and b) to be far larger than D. This finding may have important consequences for public health in cases where the level of shot noise exceeds some noise floor corresponding to equilibrium biological processes. An estimate of this noise floor is made using the example of potassium-40, a beta-emitting radioisotope universally present in living tissue.

  6. Noise Reduction in the SSNPA

    Science.gov (United States)

    Gomez, M.; Roquemore, L.; Darrow, D.; Liu, D.

    2004-11-01

    A solid-state neutral particle analyzer (SSNPA) is being used to detect the escape of neutral particles on the National Spherical Torus Experiment (NSTX). The SSNPA has four channels, which view the horizontal midplane of NSTX. The output amplitude of the SSNPA is proportional to radiation energy. Neutral particles with energies up to 100 keV will be observed. The SSNPA is used to link changes in neutral particle flux with plasma events. The noise level associated with standard NIM electronics prevents this. Two solutions are proposed to fix this problem: 1) Increase the signal to noise ratio (S/N) in the system or 2) Ultra-fast digitization (UFD) of the signal. New electronics are being tested to increase the S/N. A close-coupled preamp/amplifier increase the gain by ˜1000, which increases the signal before noise is introduced. Ground loop problems are also being addressed. This system is presently being tested on NSTX. With UFD, the preamplifier will be connected to the digitizer and post-shot analysis will separate the signal from the noise using of PHA software. The above solutions will be discussed.

  7. Noise Exposures of Rural Adolescents

    Science.gov (United States)

    Humann, Michael; Sanderson, Wayne; Flamme, Greg; Kelly, Kevin M.; Moore, Genna; Stromquist, Ann; Merchant, James A.

    2011-01-01

    Purpose: This project was conducted to characterize the noise exposure of adolescents living in rural and agricultural environments. Methods: From May to October, 25 adolescents ages 13 through 17, living either on a farm or a rural nonfarm, were enrolled in the study. Subjects received training on the correct operation and use of personal noise…

  8. Oscillator With Low Phase Noise

    Science.gov (United States)

    Kleinberg, Leonard L.

    1987-01-01

    Phase errors cancelled for high frequency stability. Radio-frequency oscillator achieves high stability of frequency through parallel, two-amplifier configuration in which effects cause phase noise tend to cancel each other. Circuit includes two amplifiers with resonating elements, each constitutes part of feedback loop of other. Generate same frequency because each circuit provides other with conditions necessary for oscillation.

  9. Noise-based Stego-ECC

    Directory of Open Access Journals (Sweden)

    Rahardjo Budi

    2014-03-01

    Full Text Available A novel method of inserting noise into stream of ciphered text is proposed. The goal of inserting noise is to increase the level of uncertainty, thus making it harder for an attacker to detect data and noise. This form of steganography is implemented using Elliptic Curve Cryptography (ECC. The process of embedding the noise to the message in the encryption process and removing the noise from the message in the decryption process is proposed in this work by modifying ElGamal to allow auto detection of data and noise.

  10. Several rotor noise sources and treatments

    Energy Technology Data Exchange (ETDEWEB)

    Tangler, J. [National Renewable Energy Laboratory, Golden, CO (United States)

    1997-12-31

    Noise has been a design consideration in the development of advanced blades and turbines at the National Renewable Energy Laboratory. During atmospheric testing associated with these efforts various types of aeroacoustic noise have been encountered. This presentation discusses several of these noise sources and treatments used to mitigate or eliminate the noise. Tonal noise resulting from tip-vortex/trailing-edge interaction and laminar separation bubbles was found to be easily eliminated. Impulsive noise resulting from blade/vortex interaction for rotors that furl and that due to tower shadow can be mitigated by various means. (au)

  11. Noise radar with broadband microwave ring correlator

    Science.gov (United States)

    Susek, Waldemar; Stec, Bronislaw

    2011-06-01

    A principle of quadrature correlation detection of noise signals using an analog broadband microwave correlator is presented in the paper. Measurement results for the correlation function of noise signals are shown and application of such solution in the noise radar for precise determination of distance changes and velocity of these changes is also presented. Results for short range noise radar operation are presented both for static and moving objects. Experimental results using 2,6 - 3,6 GHz noise like waveform for the signal from a breathing human is presented. Conclusions and future plans for applications of presented detection technique in broadband noise radars bring the paper to an end.

  12. ELF noise fields: a review.

    Science.gov (United States)

    Mild, Kjell Hansson; Mattsson, Mats-Olof

    2010-08-01

    The debate as to whether low-level electromagnetic fields can affect biological systems and in the long term cause health effects has been going on for a long time. Yet the interaction of weak electromagnetic fields (EMF) with living cells, undoubtedly a most important phenomenon, is still not well understood. The exact mechanisms by which the effects are produced have not been identified. Furthermore, it is not possible to clearly define which aspects of an EMF exposure that constitute the "dose." One of the groups that contributed to solving this problem is the Bioelectromagnetics group at Catholic University of America (CUA), Washington, D.C. Their work has been devoted to investigating the physical parameters that are needed to obtain an effect of EMF exposure on biological systems, and also how to inhibit the effect. This is a review of their work on bioeffects caused by low-level EMF, their dependence on coherence time, constancy, spatial averaging, and also how the effects can be modified by an applied ELF noise magnetic field. The group has been using early chick embryos, and L929 and Daudi cells as their main experimental systems. The review also covers the work of other groups on low-level effects and the inhibition of the effects with an applied noise field. The group at CUA has shown that biological effects can be found after exposure to low-level ELF and RF electromagnetic fields, and when effects are observed, applying an ELF magnetic noise field inhibits the effects. Also, other research groups have tried to replicate the studies from the CUA group, or to apply EMF noise to suppress EMF-induced effects. Replications of the CUA effects have not always been successful. However, in all cases where the noise field has been applied to prevent an observed effect, it has been successful in eliminating the effect.

  13. Shot noise effect on noise source and noise parameter of 10-nm-scale quasi-ballistic n-/p-type MOS devices

    Science.gov (United States)

    Jeon, Jongwook; Kang, Myounggon

    2016-05-01

    In this work, we investigated the noise source and noise parameters of a quasi-ballistic MOSFET at the high-frequency regime. We presented the shot noise properties in the measured drain current noise and its impact on the induced gate noise and the noise parameters of 10-nm-scale n-/p-type MOS (N/PMOS) devices for the first time. The measured noise sources and noise parameters were carefully analyzed with the shot and thermal noise models in all operation regions. On the basis of the results, new noise parameter models are proposed and the noise performance improvement in the quasi-ballistic regime is shown.

  14. Mapping Urban Environmental Noise Using Smartphones

    Directory of Open Access Journals (Sweden)

    Jinbo Zuo

    2016-10-01

    Full Text Available Noise mapping is an effective method of visualizing and accessing noise pollution. In this paper, a noise-mapping method based on smartphones to effectively and easily measure environmental noise is proposed. By using this method, a noise map of an entire area can be created using limited measurement data. To achieve the measurement with certain precision, a set of methods was designed to calibrate the smartphones. Measuring noise with mobile phones is different from the traditional static observations. The users may be moving at any time. Therefore, a method of attaching an additional microphone with a windscreen is proposed to reduce the wind effect. However, covering an entire area is impossible. Therefore, an interpolation method is needed to achieve full coverage of the area. To reduce the influence of spatial heterogeneity and improve the precision of noise mapping, a region-based noise-mapping method is proposed in this paper, which is based on the distribution of noise in different region types tagged by volunteers, to interpolate and combine them to create a noise map. To validate the effect of the method, a comparison of the interpolation results was made to analyse our method and the ordinary Kriging method. The result shows that our method is more accurate in reflecting the local distribution of noise and has better interpolation precision. We believe that the proposed noise-mapping method is a feasible and low-cost noise-mapping solution.

  15. Noise can speed convergence in Markov chains.

    Science.gov (United States)

    Franzke, Brandon; Kosko, Bart

    2011-10-01

    A new theorem shows that noise can speed convergence to equilibrium in discrete finite-state Markov chains. The noise applies to the state density and helps the Markov chain explore improbable regions of the state space. The theorem ensures that a stochastic-resonance noise benefit exists for states that obey a vector-norm inequality. Such noise leads to faster convergence because the noise reduces the norm components. A corollary shows that a noise benefit still occurs if the system states obey an alternate norm inequality. This leads to a noise-benefit algorithm that requires knowledge of the steady state. An alternative blind algorithm uses only past state information to achieve a weaker noise benefit. Simulations illustrate the predicted noise benefits in three well-known Markov models. The first model is a two-parameter Ehrenfest diffusion model that shows how noise benefits can occur in the class of birth-death processes. The second model is a Wright-Fisher model of genotype drift in population genetics. The third model is a chemical reaction network of zeolite crystallization. A fourth simulation shows a convergence rate increase of 64% for states that satisfy the theorem and an increase of 53% for states that satisfy the corollary. A final simulation shows that even suboptimal noise can speed convergence if the noise applies over successive time cycles. Noise benefits tend to be sharpest in Markov models that do not converge quickly and that do not have strong absorbing states.

  16. [Health effects of environmental noise exposure].

    Science.gov (United States)

    Röösli, Martin

    2013-12-01

    In the EU 27 countries about 100 million persons are exposed to road traffic noise above 55 dB (LDEN) according to the European Environment Agency. Exposure to railway noise affects 16 million individuals, aircraft noise 4 million and industry noise 1 million persons. Although the proportion of people reporting to be annoyed by noise exposure is substantial, health effects of noise is rarely an issue in general practitioners' consultations. According to stress models chronic noise exposure results in an increased allostatic load by direct physiological responses as well as psychological stress responses including sleep disturbances. In relation to acute and chronic noise exposure an increase of blood pressure was observed in epidemiological studies. An association between ischemic heart diseases and noise exposure was observed in various studies. However, the data is less consistent for other cardiovascular diseases and for cognitive effects in children. The association between metabolic syndrome and noise has rarely been investigated so far. Recently an association between road traffic noise and diabetes was observed in a Danish cohort study. Given the plausibility for a noise effect, general practitioners should consider noise exposure in patients with increased cardiometabolic risk.

  17. Development of a noise metric for assessment of exposure risk to complex noises.

    Science.gov (United States)

    Zhu, Xiangdong; Kim, Jay H; Song, Won Joon; Murphy, William J; Song, Seongho

    2009-08-01

    Many noise guidelines currently use A-weighted equivalent sound pressure level L(Aeq) as the noise metric and the equal energy hypothesis to assess the risk of occupational noises. Because of the time-averaging effect involved with the procedure, the current guidelines may significantly underestimate the risk associated with complex noises. This study develops and evaluates several new noise metrics for more accurate assessment of exposure risks to complex and impulsive noises. The analytic wavelet transform was used to obtain time-frequency characteristics of the noise. 6 basic, unique metric forms that reflect the time-frequency characteristics were developed, from which 14 noise metrics were derived. The noise metrics were evaluated utilizing existing animal test data that were obtained by exposing 23 groups of chinchillas to, respectively, different types of noise. Correlations of the metrics with the hearing losses observed in chinchillas were compared and the most promising noise metric was identified.

  18. The associations between noise sensitivity, reported physical and mental health, perceived environmental quality, and noise annoyance

    Directory of Open Access Journals (Sweden)

    Dirk Schreckenberg

    2010-01-01

    Full Text Available One hundred and ninety residents around Frankfurt Airport (46% female; 17-80 years were interviewed concerning noise annoyance due to transportation noise (aircraft, road traffic, perceived mental and physical health, perceived environmental quality, and noise sensitivity. The aim of the analyses was to test whether noise sensitivity reflects partly general environmental sensitivity and is associated with an elevated susceptibility for the perception of mental and physical health. In this study, the reported physical and mental health variables were not associated with noise exposure but with noise annoyance, and were interpreted to reflect nonspecific codeterminants of annoyance rather than noise effects. Noise sensitivity was found to influence total noise annoyance and aircraft noise annoyance but to a lesser degree annoyance due to road traffic noise. Noise sensitivity was associated with reported physical health, but not with reported mental health. Noise-sensitive persons reported poorer environmental quality in their residential area than less sensitive persons in particular with regard to air traffic (including the facets noise, pollution, and contaminations and quietness. Other aspects of the perceived quality of the environment were scarcely associated with noise sensitivity. This indicates that noise sensitivity is more specific and a reliable predictor of responses to noise from the dominant source (in this case air traffic rather than a predictor of the individual perception of the environmental quality in general.

  19. Switching bilateral filter with a texture/noise detector for universal noise removal.

    Science.gov (United States)

    Lin, Chih-Hsing; Tsai, Jia-Shiuan; Chiu, Ching-Te

    2010-09-01

    In this paper, we propose a switching bilateral filter (SBF) with a texture and noise detector for universal noise removal. Operation was carried out in two stages: detection followed by filtering. For detection, we propose the sorted quadrant median vector (SQMV) scheme, which includes important features such as edge or texture information. This information is utilized to allocate a reference median from SQMV, which is in turn compared with a current pixel to classify it as impulse noise, Gaussian noise, or noise-free. The SBF removes both Gaussian and impulse noise without adding another weighting function. The range filter inside the bilateral filter switches between the Gaussian and impulse modes depending upon the noise classification result. Simulation results show that our noise detector has a high noise detection rate as well as a high classification rate for salt-and-pepper, uniform impulse noise and mixed impulse noise. Unlike most other impulse noise filters, the proposed SBF achieves high peak signal-to-noise ratio and great image quality by efficiently removing both types of mixed noise, salt-and-pepper with uniform noise and salt-and-pepper with Gaussian noise. In addition, the computational complexity of SBF is significantly less than that of other mixed noise filters.

  20. The associations between noise sensitivity, reported physical and mental health, perceived environmental quality, and noise annoyance.

    Science.gov (United States)

    Schreckenberg, Dirk; Griefahn, Barbara; Meis, Markus

    2010-01-01

    One hundred and ninety residents around Frankfurt Airport (46% female; 17-80 years) were interviewed concerning noise annoyance due to transportation noise (aircraft, road traffic), perceived mental and physical health, perceived environmental quality, and noise sensitivity. The aim of the analyses was to test whether noise sensitivity reflects partly general environmental sensitivity and is associated with an elevated susceptibility for the perception of mental and physical health. In this study, the reported physical and mental health variables were not associated with noise exposure but with noise annoyance, and were interpreted to reflect nonspecific codeterminants of annoyance rather than noise effects. Noise sensitivity was found to influence total noise annoyance and aircraft noise annoyance but to a lesser degree annoyance due to road traffic noise. Noise sensitivity was associated with reported physical health, but not with reported mental health. Noise-sensitive persons reported poorer environmental quality in their residential area than less sensitive persons in particular with regard to air traffic (including the facets noise, pollution, and contaminations) and quietness. Other aspects of the perceived quality of the environment were scarcely associated with noise sensitivity. This indicates that noise sensitivity is more specific and a reliable predictor of responses to noise from the dominant source (in this case air traffic) rather than a predictor of the individual perception of the environmental quality in general.

  1. Identification and Reduction of Turbomachinery Noise Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Communities near airports are often exposed to high noise levels due to low flying aircraft in the takeoff and landing phases of flight. Propulsion source noise is...

  2. Study on noise of precision panel saw

    Institute of Scientific and Technical Information of China (English)

    HUWan-yi; QIYing-jie; ZHANGZhao-hao; QIXiao-jie

    2003-01-01

    According to ZBJ65015-89 standard about noise level testing method of woodworking toot, the noise testing for MJg0# and MJCl125 precision panel saws was conducted by using model ND2 precision soundqevel apparatus and double frequency wave filter. The testing results showed that the unloaded running noise source of precision panel saw was mainly from main saw blade and its aeromechanic noise was the largest. The rotating speed was determined as an important factor to impact dynamic characters of precision panel saw as the unloaded running noise increased along with speed increasing. For reducing noise of precision panel saw, the first important way is to reduce the aeromechanic noise produced by main saw blade rotating at high speed; based on assuring the processing precision, choosing tow speed is a better way to drop dawn noise; from the view of design, the diameter of clamping lid is better of half of outer diameter of main saw blade.

  3. Speech production in amplitude-modulated noise

    DEFF Research Database (Denmark)

    Macdonald, Ewen N; Raufer, Stefan

    2013-01-01

    The Lombard effect refers to the phenomenon where talkers automatically increase their level of speech in a noisy environment. While many studies have characterized how the Lombard effect influences different measures of speech production (e.g., F0, spectral tilt, etc.), few have investigated...... the consequences of temporally fluctuating noise. In the present study, 20 talkers produced speech in a variety of noise conditions, including both steady-state and amplitude-modulated white noise. While listening to noise over headphones, talkers produced randomly generated five word sentences. Similar...... to previous studies, talkers raised the level of their voice in steady-state noise. While talkers also increased the level of their voice in amplitude-modulated noise, the increase was not as large as that observed in steady-state noise. Importantly, for the 2 and 4 Hz amplitude-modulated noise conditions...

  4. Simulation of synchrotron motion with rf noise

    Energy Technology Data Exchange (ETDEWEB)

    Leemann, B.T.; Forest, E.; Chattopadhyay, S.

    1986-08-01

    The theoretical formulation is described that is behind an algorithm for synchrotron phase-space tracking with rf noise and some preliminary simulation results of bunch diffusion under rf noise obtained by actual tracking.

  5. Modeling phase noise in multifunction subassemblies.

    Science.gov (United States)

    Driscoll, Michael

    2012-03-01

    Obtaining requisite phase noise performance in hardware containing multifunction circuitry requires accurate modeling of the phase noise characteristics of each signal path component, including both absolute (oscillator) and residual (non-oscillator) circuit contributors. This includes prediction of both static and vibration-induced phase noise. The model (usually in spreadsheet form) is refined as critical components are received and evaluated. Additive (KTBF) phase noise data can be reasonably estimated, based on device drive level and noise figure. However, accurate determination of component near-carrier (multiplicative) and vibration-induced noise usually must be determined via measurement. The model should also include the effects of noise introduced by IC voltage regulators and properly discriminate between common versus independent signal path residual noise contributors. The modeling can be easily implemented using a spreadsheet.

  6. Improved Spectrum Analysis Noise Radar Systems.

    Science.gov (United States)

    and evaluated. A new spectrum analysis system designed to detect moving targets is presented. Comparison is made of the detection capabilities of all four noise radar systems in the presence of extraneous noise. (Author)

  7. Airport Noise Tech Challenge Overview

    Science.gov (United States)

    Bridges, James

    2011-01-01

    The Supersonics Project, operating under NASA Aeronautics Mission Directorate#s Fundamental Aero Program, has been organized around the Technical Challenges that have historically precluded commercial supersonic flight. One of these Challenges is making aircraft that are capable of such high aerodynamic performance quiet enough around airports that they will not be objectionable. It is recognized that a successful civilian supersonic aircraft will be a system where many new technologies will come together, and for this to happen not only will new low noise propulsion concepts be required, but new engineering tools that predict the noise of the aircraft as these technologies are combined and compromised with the rest of the aircraft design. These are the two main objectives of the Airport Noise Tech Challenge. " ! As a Project in the Fundamental Aero Program, we work at a relatively low level of technology readiness. However, we have high level milestones which force us to integrate our efforts to impact systems-level activities. To keep the low-level work tied to delivering engineering tools and low-noise concepts, we have structured our milestones around development of the concepts and organized our activities around developing and applying our engineering tools to these concepts. The final deliverables in these milestones are noise prediction modules validated against the best embodiment of each concept. These will then be used in cross-disciplinary exercises to demonstrate the viability of aircraft designs to meet all the Technical Challenges. Some of the concepts being developed are shown: Fan Flow Diverters, Multi-jet Shielding, High-Aspect Ratio Embedded Nozzles, Plasma Actuated Instability Manipulation, Highly Variable Cycle Mixer- Ejectors, and Inverted Velocity Profiles. These concepts are being developed for reduced jet noise along with the design tools which describe how they perform when used in various aircraft configurations. Several key upcoming

  8. New Noise Subtraction Methods in Lattice QCD

    CERN Document Server

    Baral, Suman; Morgan, Ronald B

    2016-01-01

    Noise subtraction techniques can help reduce the statistical uncertainty in the extraction of hard to detect signals. We describe new noise subtraction methods in Lattice QCD which apply to disconnected diagram evaluations. Some of the noise suppression techniques include polynomial quark matrix methods, eigenspectrum deflation methods, and combination methods. Our most promising technique combines polynomial and Hermitian deflation subtraction methods. The overall goal is to improve the efficiency of Lattice QCD noise method algorithms.

  9. Railway noise barriers: Measurements and Simulations

    OpenAIRE

    Ausejo Prieto, Miguel; Recuero López, Manuel; Fausti, Patrizio; Cremonini, Renzo

    2009-01-01

    Trains Trains passages passages generate generate aa very very annoying annoying noise noise toto the the inhabitants inhabitants ofof their their environs environs.. To To reduce reduce this this annoyance annoyance, noise noise barriers barriers are are installed installed near near several several railway railway lines lines.. Nowadays Nowadays, acoustic acoustic simulation simulation programs programs are are used used inin order order toto optimize optimize the the design design ofof the...

  10. BACKGROUND NOISE LEVELS IN STUDIOS AND AUDITORIA

    OpenAIRE

    James, A.

    1990-01-01

    The specification of background noise levels for auditoria must strike a balance between the lowest possible noise level from services and the need for some "masking" of extraneous sources. Studios are often designed to provide a suitable level of masking, using either aerodynamic or electronically-generated white noise. Data on noise levels in a large number of auditoria have been examined to determine whether a similar process is applicable to these. A wide range of seemingly arbitrary desi...

  11. Speech endpoint detection in real noise environments

    Institute of Scientific and Technical Information of China (English)

    GUO Yanmeng; FU Qiang; YAN Yonghong

    2007-01-01

    A method of speech endpoint detection in environments of complicated additive noise is presented. Based on the analysis of noise, an adaptive model of stationary noise is proposed to detect the section where the signal is nonstationary. Then the voice is detected in this section by its harmonic structure, and the accurate endpoint is searched using energy.Compared with the typical algorithms, this algorithm operates reliably in most real noise environments.

  12. Shot noise suppression in avalanche photodiodes.

    Science.gov (United States)

    Ma, Feng; Wang, Shuling; Campbell, Joe C

    2005-10-21

    We identify a new shot noise suppression mechanism in a thin (approximately 100 nm) heterostructure avalanche photodiode. In the low-gain regime the shot noise is suppressed due to temporal correlations within amplified current pulses. We demonstrate in a Monte Carlo simulation that the effective excess noise factors can be < 1, and reconcile the apparent conflict between theory and experiments. This shot noise suppression mechanism is independent of known mechanisms such as Coulomb interaction, or reflection at heterojunction interfaces.

  13. Restaurant noise, hearing loss, and hearing aids.

    OpenAIRE

    Lebo, C P; M.F. Smith; Mosher, E R; Jelonek, S J; Schwind, D R; Decker, K E; Krusemark, H J; Kurz, P L

    1994-01-01

    Our multidisciplinary team obtained noise data in 27 San Francisco Bay Area restaurants. These data included typical minimum, peak, and average sound pressure levels; digital tape recordings; subjective noise ratings; and on-site unaided and aided speech discrimination tests. We report the details and implications of these noise measurements and provide basic information on selecting hearing aids and suggestions for coping with restaurant noise.

  14. Restaurant noise, hearing loss, and hearing aids.

    Science.gov (United States)

    Lebo, C P; Smith, M F; Mosher, E R; Jelonek, S J; Schwind, D R; Decker, K E; Krusemark, H J; Kurz, P L

    1994-07-01

    Our multidisciplinary team obtained noise data in 27 San Francisco Bay Area restaurants. These data included typical minimum, peak, and average sound pressure levels; digital tape recordings; subjective noise ratings; and on-site unaided and aided speech discrimination tests. We report the details and implications of these noise measurements and provide basic information on selecting hearing aids and suggestions for coping with restaurant noise.

  15. Mitigating Noise for the HFC Upstream Channel

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Provides the methods to mitigate noise for the upstream channel over HFC networks. We first briefly discuss the HFC network topology, then we describe the sources of noise, the mechanism to form noise, the characteristics of their spectrum, etc. In light of the mechanism to form noise and the characteristics of their spectrum, many methods are put forward in this paper. These methods are evaluated with implementation.

  16. Effects of environmental noise on sleep.

    Science.gov (United States)

    Hume, Kenneth I; Brink, Mark; Basner, Mathias

    2012-01-01

    This paper summarizes the findings from the past 3 year's research on the effects of environmental noise on sleep and identifies key future research goals. The past 3 years have seen continued interest in both short term effects of noise on sleep (arousals, awakenings), as well as epidemiological studies focusing on long term health impacts of nocturnal noise exposure. This research corroborated findings that noise events induce arousals at relatively low exposure levels, and independent of the noise source (air, road, and rail traffic, neighbors, church bells) and the environment (home, laboratory, hospital). New epidemiological studies support already existing evidence that night-time noise is likely associated with cardiovascular disease and stroke in the elderly. These studies collectively also suggest that nocturnal noise exposure may be more relevant for the genesis of cardiovascular disease than daytime noise exposure. Relative to noise policy, new effect-oriented noise protection concepts, and rating methods based on limiting awakening reactions were introduced. The publications of WHO's ''Night Noise Guidelines for Europe'' and ''Burden of Disease from Environmental Noise'' both stress the importance of nocturnal noise exposure for health and well-being. However, studies demonstrating a causal pathway that directly link noise (at ecological levels) and disturbed sleep with cardiovascular disease and/or other long term health outcomes are still missing. These studies, as well as the quantification of the impact of emerging noise sources (e.g., high speed rail, wind turbines) have been identified as the most relevant issues that should be addressed in the field on the effects of noise on sleep in the near future.

  17. Noise Effects on Synchronized Globally Coupled Oscillators

    OpenAIRE

    Moro, Esteban; Sánchez, Angel

    1998-01-01

    The synchronized phase of globally coupled identical nonlinear oscillators subject to noise fluctuations is studied by means of a new analytical approach able to tackle general couplings, nonlinearities, and noise temporal correlations. Our results show that the interplay between coupling and noise modi es the e ective frequency of the system in a nontrivial way. Whereas for linear couplings the e ect of noise is always to increase the e ective frequency, for nonlinear coupling...

  18. Urban background noise mapping: the general model

    NARCIS (Netherlands)

    Wei, W.; Botteldooren, D.; Renterghem, T. van; Hornikx, M.; Forssen, J.; Salomons, E.; Ogren, M.

    2014-01-01

    Surveys show that inhabitants of dwellings exposed to high noise levels benefit from having access to a quiet side. However, current practice in noise prediction often underestimates the noise levels at a shielded façade. Multiple reflections between façades in street canyons and inner yards are com

  19. Combustion and Engine-Core Noise

    Science.gov (United States)

    Ihme, Matthias

    2017-01-01

    The implementation of advanced low-emission aircraft engine technologies and the reduction of noise from airframe, fan, and jet exhaust have made noise contributions from an engine core increasingly important. Therefore, meeting future ambitious noise-reduction goals requires the consideration of engine-core noise. This article reviews progress on the fundamental understanding, experimental analysis, and modeling of engine-core noise; addresses limitations of current techniques; and identifies opportunities for future research. After identifying core-noise contributions from the combustor, turbomachinery, nozzles, and jet exhaust, they are examined in detail. Contributions from direct combustion noise, originating from unsteady combustion, and indirect combustion noise, resulting from the interaction of flow-field perturbations with mean-flow variations in turbine stages and nozzles, are analyzed. A new indirect noise-source contribution arising from mixture inhomogeneities is identified by extending the theory. Although typically omitted in core-noise analysis, the impact of mean-flow variations and nozzle-upstream perturbations on the jet-noise modulation is examined, providing potential avenues for future core-noise mitigation.

  20. Complex noise exposures: an energy analysis.

    Science.gov (United States)

    Ahroon, W A; Hamernik, R P; Davis, R I

    1993-02-01

    Industrial noise environments usually present a complex stimulus to the exposed individual. These environments often contain mixtures of multiply reflected impact noises and a relatively Gaussian broadband noise. Noise exposure standards do not consider the possibility of interactions between the two classes of noise that can exacerbate the amount of hearing trauma. This paper presents the results of a large series of experiments designed to document the hazard posed to hearing from complex noise exposures. Twenty-three groups of chinchillas with 5 to 11 animals per group (total N = 135) were exposed for 5 days to either octave bands of noise, impacts alone, or combinations of impact and octave bands of noise. Evoked potential measures of hearing thresholds and cochleograms were used to quantify the noise-induced trauma. The results show that, for sound exposure levels (SEL) which produce less than approximately 10 dB PTS (permanent threshold shift) or 5% total sensory cell loss, equal-energy exposures tend to produce equivalent effects on hearing. However, there is a range of at least 10 dB in the SEL parameter where hearing loss from equal-energy exposures at a particular SEL can be exacerbated by increasing the repetition rate of the impacts or by the addition of a Gaussian low-level noise. The exacerbation of trauma from the addition of a Gaussian continuous noise is dependent upon the spectrum of that noise.

  1. Wind noise under a pine tree canopy.

    Science.gov (United States)

    Raspet, Richard; Webster, Jeremy

    2015-02-01

    It is well known that infrasonic wind noise levels are lower for arrays placed in forests and under vegetation than for those in open areas. In this research, the wind noise levels, turbulence spectra, and wind velocity profiles are measured in a pine forest. A prediction of the wind noise spectra from the measured meteorological parameters is developed based on recent research on wind noise above a flat plane. The resulting wind noise spectrum is the sum of the low frequency wind noise generated by the turbulence-shear interaction near and above the tops of the trees and higher frequency wind noise generated by the turbulence-turbulence interaction near the ground within the tree layer. The convection velocity of the low frequency wind noise corresponds to the wind speed above the trees while the measurements showed that the wind noise generated by the turbulence-turbulence interaction is near stationary and is generated by the slow moving turbulence adjacent to the ground. Comparison of the predicted wind noise spectrum with the measured wind noise spectrum shows good agreement for four measurement sets. The prediction can be applied to meteorological estimates to predict the wind noise under other pine forests.

  2. Noise Reduction in an Undergraduate Library.

    Science.gov (United States)

    Bird, Charles P.; Puglisi, Dawn D.

    1984-01-01

    Reports on program initiated to reduce noise in undergraduate library through combination of space reallocation, rule changes, and staff monitoring of noise. Objective and subjective measures of noise (sound-level readings, preintervention and postintervention questionnaires) and results of intervention program are discussed. Memo distributed on…

  3. Noise Analysis of Switched-Current Circuits

    DEFF Research Database (Denmark)

    Jørgensen, Ivan Harald Holger; Bogason, Gudmundur

    1999-01-01

    The understanding of noise in analog sampled data systems is vital for the design of high resolution circuitry in the discrete time domain. In this paper a general description of sampled and held noise is presened. The noise calculations are verified by measurements on an analog delay line implem...

  4. Noise Analysis of Switched-Current Circuits

    DEFF Research Database (Denmark)

    Jørgensen, Ivan Harald Holger; Bogason, Gudmundur

    1998-01-01

    The understanding of noise in analog sampled data systems is vital for the design of high resolution circuitry. In this paper a general description of sampled and held noise is presented. The noise calculations are verified by measurements on an analog delay line implemented using switched-curren...

  5. Policy and the evaluation of aircraft noise

    NARCIS (Netherlands)

    Kroesen, M.; Molin, E.J.E.; Van Wee, G.P.

    2010-01-01

    In this paper, we hypothesize and test the ideas that (1) people’s subjectivity in relation to aircraft noise is shaped by the policy discourse, (2) this results in a limited number of frames towards aircraft noise, (3) the frames inform people how to think and feel about aircraft noise and (4) the

  6. Research of Modified LMS Adaptive Noise Cancellation

    Institute of Scientific and Technical Information of China (English)

    YANG Ming-sheng; LI Yan-peng

    2003-01-01

    Noise cancellation is very important in the field of signal processing. In this paper, the designation of a modified LMS Adaptive Noise Cancellation is demonstrated in detail; the model is simulated. We have compared the performance of the new model with the old model. The result of the experiments shows that this designation improves the noise cancellation′s performance greatly.

  7. 14 CFR 36.103 - Noise limits.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Noise limits. 36.103 Section 36.103... Noise limits. (a) For subsonic transport category large airplanes and subsonic jet airplanes compliance... greater than the Stage 3 noise limit prescribed in section B36.5(c) of appendix B of this part. (c)...

  8. Inter modulation noise in trans linear filters

    Energy Technology Data Exchange (ETDEWEB)

    Martini, G.; Svelto, V. [Pavia Univ., Pavia (Italy). Dipt. di Elettronica

    1999-06-01

    The noise properties of trans linear filters operated in class A and class AB is examined, discussing how the output noise power depends on the circuit topology. It is shown that for in band useful signal the output noise does not depend on the relative position of the transistors in the filter.

  9. Expectations of two-level telegraph noise

    CERN Document Server

    Fern, J

    2006-01-01

    We find expectation values of functions of time integrated two-level telegraph noise. Expectation values of this noise are evaluated under simple control pulses. Both the Gaussian limit and $1/f$ noise are considered. We apply the results to a specific superconducting quantum computing example, which illustrates the use of this technique for calculating error probabilities.

  10. Noise Tracking Using DFT Domain Subspace Decompositions

    NARCIS (Netherlands)

    Hendriks, R.C.; Jensen, J.; Heusdens, R.

    2008-01-01

    All discrete Fourier transform (DFT) domain-based speech enhancement gain functions rely on knowledge of the noise power spectral density (PSD). Since the noise PSD is unknown in advance, estimation from the noisy speech signal is necessary. An overestimation of the noise PSD will lead to a loss in

  11. Sampled Noise in Switched Current Circuits

    DEFF Research Database (Denmark)

    Jørgensen, Ivan Herald Holger; Bogason, Gudmundur

    1997-01-01

    The understanding of noise in analog sampled data systems is vital for the design of high resolution circuitry. In this paper a general description of sampled and held noise is presented. The noise calculations are verified by measurements on an analog delay line implemented using switched-current...

  12. Noise Tracking Using DFT Domain Subspace Decompositions

    NARCIS (Netherlands)

    Hendriks, R.C.; Jensen, J.; Heusdens, R.

    2008-01-01

    All discrete Fourier transform (DFT) domain-based speech enhancement gain functions rely on knowledge of the noise power spectral density (PSD). Since the noise PSD is unknown in advance, estimation from the noisy speech signal is necessary. An overestimation of the noise PSD will lead to a loss in

  13. Psychophysical measurement of night vision goggle noise

    Science.gov (United States)

    Glasgow, Rachael L.; Marasco, Peter L.; Havig, Paul R.; Martinsen, Gary L.; Reis, George A.; Heft, Eric L.

    2003-09-01

    Pilots, developers, and other users of night-vision goggles (NVGs) have pointed out that different NVG image intensifier tubes have different subjective noise characteristics. Currently, no good model of the visual impact of NVG noise exists. Because it is very difficult to objectively measure the noise of a NVG, a method for assessing noise subjectively using simple psychophysical procedures was developed. This paper discusses the use of a computer program to generate noise images similar to what an observer sees through an NVG, based on filtered white noise. The images generated were based on 1/f (where f is frequency) filtered white noise with several adjustable parameters. Adjusting each of these parameters varied different characteristics of the noise. This paper discusses a study where observers compared the computer-generated noise images to true NVG noise and were asked to determine which computer-generated image was the best representation of the true noise. This method was repeated with different types of NVGs and at different luminance levels to study what NVG parameters cause variations in NVG noise.

  14. 14 CFR 36.801 - Noise measurement.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Noise measurement. 36.801 Section 36.801 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT NOISE STANDARDS: AIRCRAFT TYPE AND AIRWORTHINESS CERTIFICATION Helicopters § 36.801 Noise measurement. For primary,...

  15. Correlated noise in a logistic growth model

    Science.gov (United States)

    Ai, Bao-Quan; Wang, Xian-Ju; Liu, Guo-Tao; Liu, Liang-Gang

    2003-02-01

    The logistic differential equation is used to analyze cancer cell population, in the presence of a correlated Gaussian white noise. We study the steady state properties of tumor cell growth and discuss the effects of the correlated noise. It is found that the degree of correlation of the noise can cause tumor cell extinction.

  16. Using noise to shape motor learning.

    Science.gov (United States)

    Thorp, Elias B; Kording, Konrad P; Mussa-Ivaldi, Ferdinando A

    2017-02-01

    Each of our movements is selected from any number of alternative movements. Some studies have shown evidence that the central nervous system (CNS) chooses to make the specific movements that are least affected by motor noise. Previous results showing that the CNS has a natural tendency to minimize the effects of noise make the direct prediction that if the relationship between movements and noise were to change, the specific movements people learn to make would also change in a predictable manner. Indeed, this has been shown for well-practiced movements such as reaching. Here, we artificially manipulated the relationship between movements and visuomotor noise by adding noise to a motor task in a novel redundant geometry such that there arose a single control policy that minimized the noise. This allowed us to see whether, for a novel motor task, people could learn the specific control policy that minimized noise or would need to employ other compensation strategies to overcome the added noise. As predicted, subjects were able to learn movements that were biased toward the specific ones that minimized the noise, suggesting not only that the CNS can learn to minimize the effects of noise in a novel motor task but also that artificial visuomotor noise can be a useful tool for teaching people to make specific movements. Using noise as a teaching signal promises to be useful for rehabilitative therapies and movement training with human-machine interfaces.

  17. Control strategies for aircraft airframe noise reduction

    Institute of Scientific and Technical Information of China (English)

    Li Yong; Wang Xunnian; Zhang Dejiu

    2013-01-01

    With the development of low-noise aircraft engine,airframe noise now represents a major noise source during the commercial aircraft's approach to landing phase.Noise control efforts have therefore been extensively focused on the airframe noise problems in order to further reduce aircraft overall noise.In this review,various control methods explored in the last decades for noise reduction on airframe components including high-lift devices and landing gears are summarized.We introduce recent major achievements in airframe noise reduction with passive control methods such as fairings,deceleration plates,splitter plates,acoustic liners,slat cove cover and side-edge replacements,and then discuss the potential and control mechanism of some promising active flow control strategies for airframe noise reduction,such as plasma technique and air blowing/suction devices.Based on the knowledge gained throughout the extensively noise control testing,a few design concepts on the landing gear,high-lift devices and whole aircraft are provided for advanced aircraft low-noise design.Finally,discussions and suggestions are given for future research on airframe noise reduction.

  18. QUIESST Guidebook to Noise Reducing Devices optimisation

    NARCIS (Netherlands)

    Clairbois, J.P.; Roo, F. de; Garai, M.; Conter, M.; Defrance, J.; Oltean-Dumbrava, C.A.; Durso, C.

    2012-01-01

    The aim of this guidebook is to become a reference tool for noise mitigation through a better use of Noise Reducing Devices (NRD) (e.g.: Noise Barriers or sound Absorptive Claddings). It targets all the stakeholders involved in NRD projects (designers, manufacturers, authorities, construction compan

  19. Speech perception of noise with binary gains

    DEFF Research Database (Denmark)

    Wang, DeLiang; Kjems, Ulrik; Pedersen, Michael Syskind

    2008-01-01

    For a given mixture of speech and noise, an ideal binary time-frequency mask is constructed by comparing speech energy and noise energy within local time-frequency units. It is observed that listeners achieve nearly perfect speech recognition from gated noise with binary gains prescribed...

  20. QUIESST Guidebook to Noise Reducing Devices optimisation

    NARCIS (Netherlands)

    Clairbois, J.P.; Roo, F. de; Garai, M.; Conter, M.; Defrance, J.; Oltean-Dumbrava, C.A.; Durso, C.

    2012-01-01

    The aim of this guidebook is to become a reference tool for noise mitigation through a better use of Noise Reducing Devices (NRD) (e.g.: Noise Barriers or sound Absorptive Claddings). It targets all the stakeholders involved in NRD projects (designers, manufacturers, authorities, construction

  1. Policy and the evaluation of aircraft noise

    NARCIS (Netherlands)

    Kroesen, M.; Molin, E.J.E.; Van Wee, G.P.

    2010-01-01

    In this paper, we hypothesize and test the ideas that (1) people’s subjectivity in relation to aircraft noise is shaped by the policy discourse, (2) this results in a limited number of frames towards aircraft noise, (3) the frames inform people how to think and feel about aircraft noise and (4) the

  2. Urban background noise mapping: the general model

    NARCIS (Netherlands)

    Wei, W.; Botteldooren, D.; Renterghem, T. van; Hornikx, M.; Forssen, J.; Salomons, E.; Ogren, M.

    2014-01-01

    Surveys show that inhabitants of dwellings exposed to high noise levels benefit from having access to a quiet side. However, current practice in noise prediction often underestimates the noise levels at a shielded façade. Multiple reflections between façades in street canyons and inner yards are com

  3. Noise canceling in-situ detection

    Science.gov (United States)

    Walsh, David O.

    2014-08-26

    Technologies applicable to noise canceling in-situ NMR detection and imaging are disclosed. An example noise canceling in-situ NMR detection apparatus may comprise one or more of a static magnetic field generator, an alternating magnetic field generator, an in-situ NMR detection device, an auxiliary noise detection device, and a computer.

  4. Classroom Noise and Teachers' Voice Production

    Science.gov (United States)

    Rantala, Leena M.; Hakala, Suvi; Holmqvist, Sofia; Sala, Eeva

    2015-01-01

    Purpose: The aim of this study was to research the associations between noise (ambient and activity noise) and objective metrics of teachers' voices in real working environments (i.e., classrooms). Method: Thirty-two female and 8 male teachers from 14 elementary schools were randomly selected for the study. Ambient noise was measured during breaks…

  5. Noise Control in Propeller-Driven Aircraft

    Science.gov (United States)

    Rennison, D. C.; Wilby, J. F.

    1983-01-01

    Analytical model predicts noise levels inside propeller-driven aircraft during cruise at mach 0.8. Double wall sidewalls minimize interior noise and weight. Model applied to three aircraft with fuselages of different size (wide-body, narrow-body, and small-diameter) to determine noise reductions required to achieve A-weighted sound level not to exceed 80 dB.

  6. Future impact of road and railway noise

    NARCIS (Netherlands)

    Dittrich, M.G.; Roo, F. de; Eisses, R.R.

    2015-01-01

    An exploratory study bas been undertaken to put into perspective future impact of road and railway noise until 2050 in The Netherlands, taking into account potential economic and mobitity growth, noise policy and legislation, demography and technical progress. Estimates were made of average noise le

  7. Noise in (double) relaxation oscillation SQUIDs

    NARCIS (Netherlands)

    Adelerhof, Derk Jan; Adelerhof, Derk Jan; Flokstra, Jakob; Rogalla, Horst

    1994-01-01

    We have modelled the effect of two intrinsic noise sources on the flux noise spectral density of (Double) Relaxation Oscillation SQUIDs ((D)ROSs) based on hysteretic Josephson tunnel junctions. An important noise source is the spread in the critical current of the SQUID due to thermal fluctuations.

  8. Underwater noise generated by offshore pile driving

    NARCIS (Netherlands)

    Tsouvalas, A.

    2015-01-01

    Anthropogenic noise emission in the marine environment has always been an environmental issue of serious concern. In particular, the noise generated during the installation of foundation piles is considered to be one of the most significant sources of underwater noise pollution. This is mainly attri

  9. Image upconversion, a low noise infrared sensor?

    DEFF Research Database (Denmark)

    for detection of infrared images. Silicon cameras have much smaller intrinsic noise than their IR counter part- some models even offer near single photon detection capability. We demonstrate that an ordinary CCD camera combined with a low noise upconversion has superior noise characteristics when compared...

  10. Image upconversion - a low noise infrared sensor?

    DEFF Research Database (Denmark)

    Dam, Jeppe Seidelin; Tidemand-Lichtenberg, Peter; Pedersen, Christian

    for detection of infrared images. Silicon cameras have much smaller intrinsic noise than their IR counter part- some models even offer near single photon detection capability. We demonstrate that an ordinary CCD camera combined with a low noise upconversion has superior noise characteristics when compared...

  11. Restriction of shot noise and material noise in a multilevel photochromic memory on signal-to-noise ratio

    Institute of Scientific and Technical Information of China (English)

    Zhang Qi-Cheng; Ni Yi; Xu Duan-Yi; Hu Heng

    2006-01-01

    The recording density of multilevel photochromic memory is limited by the signal-to-noise ratio (SNR) of the readout signal. In this paper, shot noise and material noise are investigated through theoretical analysis of SNR. When the bandwidth of a system is less than 1MHz, the material noise takes a prominent position; when the bandwidth of the system is more than 10MHz, the shot noise becomes dominant. The thickness of recording layer can be optimized to maximize the SNR and reduce the influence of the bandwidth of the system on SNR.

  12. Quantum Noise in Laser Diodes

    Science.gov (United States)

    Giacobino, E.; Marin, F.; Bramati, A.; Jost, V.; Poizat, J. Ph.; Roch, J.-F.; Grangier, P.; Zhang, T.-C.

    1996-01-01

    We have investigated the intensity noise of single mode laser diodes, either free-running or using different types of line narrowing techniques at room temperature. We have measured an intensity squeezing of 1.2 dB with grating-extended cavity lasers and 1.4 dB with injection locked lasers (respectively 1.6 dB and 2.3 dB inferred at the laser output). We have observed that the intensity noise of a free-running nominally single mode laser diode results from a cancellation effect between large anti-correlated fluctuations of the main mode and of weak longitudinal side modes. Reducing the side modes by line narrowing techniques results in intensity squeezing.

  13. Global Noise and Global Englishes

    Directory of Open Access Journals (Sweden)

    Alastair Pennycook

    2013-09-01

    Full Text Available Global Noise: Rap and Hip-Hop Outside the USA, alluding to Tricia Rose’s US rap-music book, Black Noise, aims to do much more than merely extend the reach of the study of rap and hip-hop beyond the USA, as its subtitle might suggest. While acknowledging the importance of the work of both Rose and Potter, this collection’s editor, Tony Mitchell, contests their respective views that rap and hip-hop are essentially expressions of African-American culture, and that all forms of rap and hip-hop derive from these origins. He argues that these forms have become ‘a vehicle for global youth affiliations and a tool for reworking local iden- tity all over the world’.

  14. Low-noise pulse conditioner

    Science.gov (United States)

    Bird, D.A.

    1981-06-16

    A low-noise pulse conditioner is provided for driving electronic digital processing circuitry directly from differentially induced input pulses. The circuit uses a unique differential-to-peak detector circuit to generate a dynamic reference signal proportional to the input peak voltage. The input pulses are compared with the reference signal in an input network which operates in full differential mode with only a passive input filter. This reduces the introduction of circuit-induced noise, or jitter, generated in ground referenced input elements normally used in pulse conditioning circuits, especially speed transducer processing circuits. This circuit may be used for conditioning the sensor signal from the Fidler coil in a gas centrifuge for separation of isotopic gaseous mixtures.

  15. Kernel Generalized Noise Clustering Algorithm

    Institute of Scientific and Technical Information of China (English)

    WU Xiao-hong; ZHOU Jian-jiang

    2007-01-01

    To deal with the nonlinear separable problem, the generalized noise clustering (GNC) algorithm is extended to a kernel generalized noise clustering (KGNC) model. Different from the fuzzy c-means (FCM) model and the GNC model which are based on Euclidean distance, the presented model is based on kernel-induced distance by using kernel method. By kernel method the input data are nonlinearly and implicitly mapped into a high-dimensional feature space, where the nonlinear pattern appears linear and the GNC algorithm is performed. It is unnecessary to calculate in high-dimensional feature space because the kernel function can do itjust in input space. The effectiveness of the proposed algorithm is verified by experiments on three data sets. It is concluded that the KGNC algorithm has better clustering accuracy than FCM and GNC in clustering data sets containing noisy data.

  16. Propeller aircraft interior noise model

    Science.gov (United States)

    Pope, L. D.; Wilby, E. G.; Wilby, J. F.

    1984-01-01

    An analytical model was developed to predict the interior noise of propeller-driven aircraft. The fuselage model is that of a cylinder with a structurally-integral floor. The cabin sidewall is stiffened by stringers and ring frames, and the floor by longitudinal beams. The cabin interior is covered with a sidewall treatments consisting of layers of porous material and an impervious trim septum. Representation of the propeller pressure field is utilized as input data in the form of the propeller noise signature at a series of locations on a grid over the fuselage structure. Results obtained from the analytical model are compared with test data measured by NASA in a scale model cylindrical fuselage excited by a model propeller.

  17. Noise-induced quantum transport

    OpenAIRE

    Ghosh, Pulak Kumar; Barik, Debashis; Ray, Deb Shankar

    2004-01-01

    We analyze the problem of directed quantum transport induced by external exponentially correlated telegraphic noise. In addition to quantum nature of the heat bath, nonlinearity of the periodic system potential brings in quantum contribution. We observe that quantization, in general, enhances classical current at low temperature, while the differences become insignificant at higher temperature. Interplay of quantum diffusion and quantum correction to system potential is analyzed for various r...

  18. Road-Traffic Noise: Annoyance, Risk Perception, and Noise Sensitivity in the Finnish Adult Population

    Science.gov (United States)

    Okokon, Enembe Oku; Turunen, Anu W.; Ung-Lanki, Sari; Vartiainen, Anna-Kaisa; Tiittanen, Pekka; Lanki, Timo

    2015-01-01

    Exposure to road-traffic noise commonly engenders annoyance, the extent of which is determined by factors not fully understood. Our aim was to estimate the prevalence and determinants of road-traffic noise annoyance and noise sensitivity in the Finnish adult population, while comparing the perceptions of road-traffic noise to exhausts as environmental health problems. Using a questionnaire that yielded responses from 1112 randomly selected adult Finnish respondents, we estimated road-traffic noise- and exhausts-related perceived exposures, health-risk perceptions, and self-reported annoyance on five-point scales, while noise sensitivity estimates were based on four questions. Determinants of noise annoyance and sensitivity were investigated using multivariate binary logistic regression and linear regression models, respectively. High or extreme noise annoyance was reported by 17% of respondents. Noise sensitivity scores approximated a Gaussian distribution. Road-traffic noise and exhausts were, respectively, considered high or extreme population-health risks by 22% and 27% of respondents. Knowledge of health risks from traffic noise, OR: 2.04 (1.09–3.82) and noise sensitivity, OR: 1.07 (1.00–1.14) were positively associated with annoyance. Knowledge of health risks (p traffic noise, and perceive it to be a significant health risk, almost comparable to traffic exhausts. There is no distinct noise-sensitive population subgroup. Knowledge of health risks of road-traffic noise, and attitudinal variables are associated with noise annoyance and sensitivity. PMID:26016432

  19. Proceedings of the 1987 national conference on noise control engineering: High technology for noise control

    Energy Technology Data Exchange (ETDEWEB)

    Tichy, J.; Hayek, S.

    1987-01-01

    This book consists of nine sections, each containing several papers. The section titles are: Emission: Noise Sources; Physical Phenomena; Noise Control Elements; Vibration: Generation, Transmission, Isolation and Reduction; Immission: Physical Aspects of Environmental Noise; Immission: Effects of Noise; Analysis; Requirements; and Biomedical Uses of Acoustics.

  20. Research on the characteristics of noise source on heading face and noise propagation in mine laneway

    Institute of Scientific and Technical Information of China (English)

    PENG You-duo; XIE Wei-hua; XIE Zhi-yong; PENG Chang-qing; YIN Xi

    2012-01-01

    Based on the complexity and dynamic random analysis of machine noise source in mine heading face,this article established the noise pressure mathematical model of noise propagation in mine laneway of different noise sources,carried out noise propagation numerical simulation in long space,and revealed noise propagation law of more radiated noise sources in the mine roadway.The results show that,under conditions that the total noise power is always the same,regardless of point source,surface noise source,or body noise source,the corresponding noise attenuation trend along the mine laneway and attenuation curve shape are basically the same.However,the attenuation velocity corresponding to complex stereo noise source is slower than single point source and the noise pressure value is higher than the single point source.The actual noise of measured values is close to the theoretical value or,say,there is little error for complex stereo noise source,whereas the error to single point source and surface noise is higher,respectively.

  1. 78 FR 19355 - Noise Exposure Map Notice: Receipt of Noise Compatibility Program and Request for Review

    Science.gov (United States)

    2013-03-29

    ... Federal Aviation Administration Noise Exposure Map Notice: Receipt of Noise Compatibility Program and... Aviation Administration (FAA) announces its determination that the noise exposure maps submitted by Tucson... Aviation Safety and Noise Abatement Act, hereinafter referred to as ``the Act'') and 14 CFR Part 150 are...

  2. Stochastic noise in splicing machinery.

    Science.gov (United States)

    Melamud, Eugene; Moult, John

    2009-08-01

    The number of known alternative human isoforms has been increasing steadily with the amount of available transcription data. To date, over 100 000 isoforms have been detected in EST libraries, and at least 75% of human genes have at least one alternative isoform. In this paper, we propose that most alternative splicing events are the result of noise in the splicing process. We show that the number of isoforms and their abundance can be predicted by a simple stochastic noise model that takes into account two factors: the number of introns in a gene and the expression level of a gene. The results strongly support the hypothesis that most alternative splicing is a consequence of stochastic noise in the splicing machinery, and has no functional significance. The results are also consistent with error rates tuned to ensure that an adequate level of functional product is produced and to reduce the toxic effect of accumulation of misfolding proteins. Based on simulation of sampling of virtual cDNA libraries, we estimate that error rates range from 1 to 10% depending on the number of introns and the expression level of a gene.

  3. [Occupational noise exposure and hypertension].

    Science.gov (United States)

    Santana, V S; Barberino, J L

    1995-12-01

    The hypothesis that occupational noise exposure is positively associated with hypertension was examined in a cross-sectional study carried out on a group of patients who were enrolled at the Occupational Health Unit of the Unified Health System, situated in Salvador city, the capital of Bahia state, Brazil. Data were obtained from 276 medical records, corresponding to all patients newly registered during the first six months of 1992. Data on noise exposure come from both reported occupational exposure history and clinical diagnosis of occupational noise-induced hearing loss. Hypertension diagnosis complies with World Health Organization criteria, as well as with the history of antihypertensive treatment. Stratified analysis and unconditional logistic regression modeling show results that do not support the study hypothesis: there are no differences between systolic or diastolic blood pressure or between proportion of hypertension for exposed and non exposed groups. However, statiscally significant (alpha = 0.05) increment of the effect measured was reported among workers who reported low educational level (below elementary). This could be another evidence of socially related inequalities underlying exposure distribution among workers at the workplace, which should be addressed, at greater depth, in future studies.

  4. Current noise in tunnel junctions

    Energy Technology Data Exchange (ETDEWEB)

    Frey, Moritz; Grabert, Hermann [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder-Strasse 3, 79104, Freiburg (Germany)

    2017-06-15

    We study current fluctuations in tunnel junctions driven by a voltage source. The voltage is applied to the tunneling element via an impedance providing an electromagnetic environment of the junction. We use circuit theory to relate the fluctuations of the current flowing in the leads of the junction with the voltage fluctuations generated by the environmental impedance and the fluctuations of the tunneling current. The spectrum of current fluctuations is found to consist of three parts: a term arising from the environmental Johnson-Nyquist noise, a term due to the shot noise of the tunneling current and a third term describing the cross-correlation between these two noise sources. Our phenomenological theory reproduces previous results based on the Hamiltonian model for the dynamical Coulomb blockade and provides a simple understanding of the current fluctuation spectrum in terms of circuit theory and properties of the average current. Specific results are given for a tunnel junction driven through a resonator. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  5. Comparison of Ising spin glass noise to flux and inductance noise in SQUIDs.

    Science.gov (United States)

    Chen, Zhi; Yu, Clare C

    2010-06-18

    Recent experiments implicate spins on the surface of metals as the source of flux and inductance noise in SQUIDs. We present Monte Carlo simulations of 2D and 3D Ising spin glasses that produce magnetization noise S(M) consistent with flux noise. At low frequencies S(M) is a maximum at the critical temperature T(C) in three dimensions, implying that flux noise should be a maximum at T(C). The second spectra of the magnetization noise and the noise in the susceptibility are consistent with experimentally measured SQUID inductance noise.

  6. Study of signal-to-noise ratio driven by colored noise

    Institute of Scientific and Technical Information of China (English)

    ZHAO Jin

    2016-01-01

    This paper investigates the signal-to-noise ratio(SNR)driven by colored noise and weak input signals. Based on the Cauchy-Schwarz and Rayleigh quotients inequalities, an analytical expression of SNR is developed, and its upper band is closely related to the Fisher information of noise. For mimicking the colored noise, we adopt the first-order moving-average model and propose the optimal input signal waveform. The stochastic resonance effect in threshold systems is demonstrated for the Gaussian mixture colored noise. The obtained results will be interesting in the case of improving the nonlinear filter performance by adding noise to the weak signal corrupted by the colored noise.

  7. Effects of environmental noise on sleep

    Directory of Open Access Journals (Sweden)

    Kenneth I Hume

    2012-01-01

    Full Text Available This paper summarizes the findings from the past 3 year′s research on the effects of environmental noise on sleep and identifies key future research goals. The past 3 years have seen continued interest in both short term effects of noise on sleep (arousals, awakenings, as well as epidemiological studies focusing on long term health impacts of nocturnal noise exposure. This research corroborated findings that noise events induce arousals at relatively low exposure levels, and independent of the noise source (air, road, and rail traffic, neighbors, church bells and the environment (home, laboratory, hospital. New epidemiological studies support already existing evidence that night-time noise is likely associated with cardiovascular disease and stroke in the elderly. These studies collectively also suggest that nocturnal noise exposure may be more relevant for the genesis of cardiovascular disease than daytime noise exposure. Relative to noise policy, new effect-oriented noise protection concepts, and rating methods based on limiting awakening reactions were introduced. The publications of WHO′s ′′Night Noise Guidelines for Europe′′ and ′′Burden of Disease from Environmental Noise′′ both stress the importance of nocturnal noise exposure for health and well-being. However, studies demonstrating a causal pathway that directly link noise (at ecological levels and disturbed sleep with cardiovascular disease and/or other long term health outcomes are still missing. These studies, as well as the quantification of the impact of emerging noise sources (e.g., high speed rail, wind turbines have been identified as the most relevant issues that should be addressed in the field on the effects of noise on sleep in the near future.

  8. Noise.

    Science.gov (United States)

    1983-09-01

    sample paths. Unfortunately, the Wiener process sample paths are of bounded variation with probability zero and all the physical sample paths are of... bounded variation . Thus non-linear filtering theory cannot be applied in practice unless we are able to choose a particular version of the conditional

  9. Productive Parasites: Thinking of Noise as Affect

    Directory of Open Access Journals (Sweden)

    Marie Thompson

    2012-11-01

    Full Text Available Drawing from Michel Serres’ notion of the parasite, this article provides a nuanced explanation for noise that distinguishes itself from prevailing negative narratives, which often seek to define noise as unwanted, undesirable or damaging sound. Such narratives have left noise vulnerable to moralising polemics, which construct silence and noise as a dichotomy between the past and present, natural and cultural, relaxing and disturbing, and, fundamentally, good and bad. This article facilitates a reconsideration of noise’s ethical connotations by proposing the notion of noise as affect.

  10. Indirect combustion noise of auxiliary power units

    Science.gov (United States)

    Tam, Christopher K. W.; Parrish, Sarah A.; Xu, Jun; Schuster, Bill

    2013-08-01

    Recent advances in noise suppression technology have significantly reduced jet and fan noise from commercial jet engines. This leads many investigators in the aeroacoustics community to suggest that core noise could well be the next aircraft noise barrier. Core noise consists of turbine noise and combustion noise. There is direct combustion noise generated by the combustion processes, and there is indirect combustion noise generated by the passage of combustion hot spots, or entropy waves, through constrictions in an engine. The present work focuses on indirect combustion noise. Indirect combustion noise has now been found in laboratory experiments. The primary objective of this work is to investigate whether indirect combustion noise is also generated in jet and other engines. In a jet engine, there are numerous noise sources. This makes the identification of indirect combustion noise a formidable task. Here, our effort concentrates exclusively on auxiliary power units (APUs). This choice is motivated by the fact that APUs are relatively simple engines with only a few noise sources. It is, therefore, expected that the chance of success is higher. Accordingly, a theoretical model study of the generation of indirect combustion noise in an Auxiliary Power Unit (APU) is carried out. The cross-sectional areas of an APU from the combustor to the turbine exit are scaled off to form an equivalent nozzle. A principal function of a turbine in an APU is to extract mechanical energy from the flow stream through the exertion of a resistive force. Therefore, the turbine is modeled by adding a negative body force to the momentum equation. This model is used to predict the ranges of frequencies over which there is a high probability for indirect combustion noise generation. Experimental spectra of internal pressure fluctuations and far-field noise of an RE220 APU are examined to identify anomalous peaks. These peaks are possible indirection combustion noise. In the case of the

  11. Calculation of thermal noise in grating reflectors

    CERN Document Server

    Heinert, Daniel; Friedrich, Daniel; Hild, Stefan; Kley, Ernst-Bernhard; Leavey, Sean; Martin, Iain W; Nawrodt, Ronny; Tünnermann, Andreas; Vyatchanin, Sergey P; Yamamoto, Kazuhiro

    2013-01-01

    Grating reflectors have been repeatedly discussed to improve the noise performance of metrological applications due to the reduction or absence of any coating material. So far, however, no quantitative estimate on the thermal noise of these reflective structures exists. In this work we present a theoretical calculation of a grating reflector's noise. We further apply it to a proposed 3rd generation gravitational wave detector. Depending on the grating geometry, the grating material and the temperature we obtain a thermal noise decrease by up to a factor of ten compared to conventional dielectric mirrors. Thus the use of grating reflectors can substantially improve the noise performance in metrological applications.

  12. Colored Noise Prediction Based on Neural Network

    Institute of Scientific and Technical Information of China (English)

    Gao Fei; Zhang Xiaohui

    2003-01-01

    A method for predicting colored noise by introducing prediction of nonhnear time series is presented By adopting three kinds of neural networks prediction models, the colored noise prediction is studied through changing the filter bandwidth for stochastic noise and the sampling rate for colored noise The results show that colored noise can be predicted The prediction error decreases with the increasing of the sampling rate or the narrowing of the filter bandwidth. If the parameters are selected properly, the prediction precision can meet the requirement of engineering implementation. The results offer a new reference way for increasing the ability for detecting weak signal in signal processing system

  13. Harmonic Retrieval in Colored ARMA Noise

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    We propose a new approach to harmonic retrieval in colored ARMA noise. A suitable filter is first used to remove all the sharp power spectrum peaks of the noisy observed process, then some kinds of cross correlation is employed to identify the noise characteristics. After filtering the noisy observed process with the identified noise characteristics again, SVD-TLS method can be applied to retrieve the harmonics. The proposed approach can be used to retrieve real-valued harmonic signals in colored ARMA noise with no restrictions on the phase coupling of harmonics and the distribution of the noise. Simulation examples show its effectiveness.

  14. Chicago transit authority train noise exposure.

    Science.gov (United States)

    Phan, Linh T; Jones, Rachael M

    2017-06-01

    To characterize noise exposure of riders on Chicago Transit Authority (CTA) trains, we measured noise levels twice on each segment of 7 of the 8 CTA train lines, which are named after colors, yielding 48 time-series measurements. We found the Blue Line has the highest noise levels compared to other train lines, with mean 76.9 dBA; and that the maximum noise level, 88.9 dBA occurred in the tunnel between the Chicago and Grand stations. Train segments involving travel through a tunnel had significantly higher noise levels than segments with travel on elevated and ground level tracks. While 8-hr doses inside the passenger cars were not estimated to exceed occupational exposure limits, train operators ride in a separate cab with operational windows and may therefore have higher noise exposures than riders. Despite the low risk of hearing loss for riders on CTA trains, in part because transit noise accounts for a small part of total daily noise exposure, 1-min average noise levels exceeded 85 dBA at times. This confirms anecdotal observations of discomfort due to noise levels, and indicates a need for noise management, particularly in tunnels.

  15. Noise Residual Learning for Noise Modeling in Distributed Video Coding

    DEFF Research Database (Denmark)

    Luong, Huynh Van; Forchhammer, Søren

    2012-01-01

    Distributed video coding (DVC) is a coding paradigm which exploits the source statistics at the decoder side to reduce the complexity at the encoder. The noise model is one of the inherently difficult challenges in DVC. This paper considers Transform Domain Wyner-Ziv (TDWZ) coding and proposes...... decoding. A residual refinement step is also introduced to take advantage of correlation of DCT coefficients. Experimental results show that the proposed techniques robustly improve the coding efficiency of TDWZ DVC and for GOP=2 bit-rate savings up to 35% on WZ frames are achieved compared with DISCOVER....

  16. Hempcrete Noise Barrier Wall for Highway Noise Insulation : Research & Construction

    OpenAIRE

    KC, Prabesh

    2016-01-01

    The purpose of this thesis was to study the possibility of Hempcrete or hemp-lime composite noise barrier walls in the highways and to construct the walls for the acoustic test according to the European Union Standards EN ISO 717-1 and ISO 10140-2 for air-borne sound insulation. The thesis was commissioned by the company Hemprefine Oy, and all the standard tests were performed in the HAMK-Ruukki Sheet Metal Centre in Hämeenlinna and the VTT Technical Research Centre of Finland Ltd in Espoo. ...

  17. Fractal characteristics for binary noise radar waveform

    Science.gov (United States)

    Li, Bing C.

    2016-05-01

    Noise radars have many advantages over conventional radars and receive great attentions recently. The performance of a noise radar is determined by its waveforms. Investigating characteristics of noise radar waveforms has significant value for evaluating noise radar performance. In this paper, we use binomial distribution theory to analyze general characteristics of binary phase coded (BPC) noise waveforms. Focusing on aperiodic autocorrelation function, we demonstrate that the probability distributions of sidelobes for a BPC noise waveform depend on the distances of these sidelobes to the mainlobe. The closer a sidelobe to the mainlobe, the higher the probability for this sidelobe to be a maximum sidelobe. We also develop Monte Carlo framework to explore the characteristics that are difficult to investigate analytically. Through Monte Carlo experiments, we reveal the Fractal relationship between the code length and the maximum sidelobe value for BPC waveforms, and propose using fractal dimension to measure noise waveform performance.

  18. Image reconstruction under non-Gaussian noise

    DEFF Research Database (Denmark)

    Sciacchitano, Federica

    During acquisition and transmission, images are often blurred and corrupted by noise. One of the fundamental tasks of image processing is to reconstruct the clean image from a degraded version. The process of recovering the original image from the data is an example of inverse problem. Due......D thesis intends to solve some of the many open questions for image restoration under non-Gaussian noise. The two main kinds of noise studied in this PhD project are the impulse noise and the Cauchy noise. Impulse noise is due to for instance the malfunctioning pixel elements in the camera sensors, errors...... that the CM estimate outperforms the MAP estimate, when the error depends on Bregman distances. This PhD project can have many applications in the modern society, in fact the reconstruction of high quality images with less noise and more details enhances the image processing operations, such as edge detection...

  19. Noise from high speed maglev systems: Noise sources, noise criteria, preliminary design guidelines for noise control, and recommendations for acoustical test facility for maglev research

    Science.gov (United States)

    Hanson, C. E.; Abbot, P.; Dyer, I.

    1993-01-01

    Noise levels from magnetically-levitated trains (maglev) at very high speed may be high enough to cause environmental noise impact in residential areas. Aeroacoustic sources dominate the sound at high speeds and guideway vibrations generate noticeable sound at low speed. In addition to high noise levels, the startle effect as a result of sudden onset of sound from a rapidly moving nearby maglev vehicle may lead to increased annoyance to neighbors of a maglev system. The report provides a base for determining the noise consequences and potential mitigation for a high speed maglev system in populated areas of the United States. Four areas are included in the study: (1) definition of noise sources; (2) development of noise criteria; (3) development of design guidelines; and (4) recommendations for a noise testing facility.

  20. Noise-based communication and computing

    CERN Document Server

    Kish, Laszlo B

    2008-01-01

    We discuss the speed-error-heat triangle and related problems with rapidly increasing energy dissipation and error rate during miniaturization. These and the independently growing need of unconditional data security have provoked non-conventional approaches in the physics of informatics. Noise-based informatics is a potentially promising possibility which is the way how biological brains process the information. Recently, it has been shown that thermal noise and its electronically enhanced versions (Johnson-like noises) can be utilized as information carrier with peculiar properties. Relevant examples are Zero power (stealth) communication, Unconditionally secure communication with Johnson(-like) noise and Kirchhoff loop and Noise-driven computing. The zero power communication utilizes the equilibrium background noise in the channel to transfer information. The unconditionally secure communication is based on the properties of Johnson(-like) noise and those of a simple Kirchhoff's loop. The scheme utilizes on...

  1. 11th International Workshop on Railway Noise

    CERN Document Server

    Anderson, David; Gautier, Pierre-Etienne; Iida, Masanobu; Nelson, James; Thompson, David; Tielkes, Thorsten; Towers, David; Vos, Paul

    2015-01-01

    The book reports on the 11th International Workshop on Railway Noise, held on 9 – 13 September, 2013, in Uddevalla, Sweden. The event, which was jointly organized by the Competence Centre Chalmers Railway Mechanics (CHARMEC) and the Departments of Applied Mechanics and Applied Acoustics at Chalmers University of Technology in Gothenburg, Sweden, covered a broad range of topics in the field of railway noise and vibration, including: prospects, legal regulations and perceptions; wheel and rail noise; prediction, measurements and monitoring; ground-borne vibration; squeal noise and structure-borne noise; and aerodynamic noise generated by high-speed trains. Further topics included: resilient track forms; grinding, corrugation and roughness; and interior noise and sound barriers. This book, which consists of a collection of peer-reviewed papers originally submitted to the workshop, not only provides readers with an overview of the latest developments in the field, but also offers scientists and engineers essent...

  2. Quantum limited heterodyne detection of spin noise

    Science.gov (United States)

    Cronenberger, S.; Scalbert, D.

    2016-09-01

    Spin noise spectroscopy is a powerful technique for studying spin relaxation in semiconductors. In this article, we propose an extension of this technique based on optical heterodyne detection of spin noise, which provides several key advantages compared to conventional spin noise spectroscopy: detection of high frequency spin noise not limited by detector bandwidth or sampling rates of digitizers, quantum limited sensitivity even in case of very weak probe power, and possible amplification of the spin noise signal. Heterodyne detection of spin noise is demonstrated on insulating n-doped GaAs. From measurements of spin noise spectra up to 0.4 Tesla, we determined the distribution of g-factors, Δg/g = 0.49%.

  3. Noise, sleep and poor health: Modeling the relationship between road traffic noise and cardiovascular problems.

    Science.gov (United States)

    Fyhri, Aslak; Aasvang, Gunn Marit

    2010-10-01

    Several adverse effects have been associated with exposure to traffic noise. Studies supporting a noise-stress-health model have suggested links between noise level and increased noradrenalin concentrations in urine, hypertension and myocardial infarction. Among the more commonly documented effects, sleep disturbances have been regarded as being the most serious. Both noise annoyance and sleep disturbance have been proposed as important mediators of the impact of noise on health. The present paper investigates the relationships among long-term noise exposure, annoyance, sleeping problems and subjective health complaints by the use of a structural equation model. Further, it aims at giving insight into how noise sensitivity is related to sleep disturbances from road traffic noise. Finally, it examines whether any effect of noise exposure or response to noise can be detected on prevalence of cardiovascular problems, when information on sleep disturbances is included in a model. Data from a questionnaire survey conducted among a population sample in Oslo (N=2786) are combined with nighttime noise levels calculated from outside each respondents dwelling, at the bedroom façade. The results of the analysis showed significant relationships between noise annoyance at night and sleeping problems. The model also showed strong links among pseudoneurological complaints, annoyance and sleeping problems, thus pointing to the importance of including information on psychosomatic disorders and mild psychological problems in future studies looking at potential health effects of noise. The analysis showed no relationship between neither noise exposure nor response to noise and cardiovascular problems.

  4. Noise-enhanced convolutional neural networks.

    Science.gov (United States)

    Audhkhasi, Kartik; Osoba, Osonde; Kosko, Bart

    2016-06-01

    Injecting carefully chosen noise can speed convergence in the backpropagation training of a convolutional neural network (CNN). The Noisy CNN algorithm speeds training on average because the backpropagation algorithm is a special case of the generalized expectation-maximization (EM) algorithm and because such carefully chosen noise always speeds up the EM algorithm on average. The CNN framework gives a practical way to learn and recognize images because backpropagation scales with training data. It has only linear time complexity in the number of training samples. The Noisy CNN algorithm finds a special separating hyperplane in the network's noise space. The hyperplane arises from the likelihood-based positivity condition that noise-boosts the EM algorithm. The hyperplane cuts through a uniform-noise hypercube or Gaussian ball in the noise space depending on the type of noise used. Noise chosen from above the hyperplane speeds training on average. Noise chosen from below slows it on average. The algorithm can inject noise anywhere in the multilayered network. Adding noise to the output neurons reduced the average per-iteration training-set cross entropy by 39% on a standard MNIST image test set of handwritten digits. It also reduced the average per-iteration training-set classification error by 47%. Adding noise to the hidden layers can also reduce these performance measures. The noise benefit is most pronounced for smaller data sets because the largest EM hill-climbing gains tend to occur in the first few iterations. This noise effect can assist random sampling from large data sets because it allows a smaller random sample to give the same or better performance than a noiseless sample gives.

  5. Noise-induced annoyance from transportation noise: short-term responses to a single noise source in a laboratory.

    Science.gov (United States)

    Kim, Jaehwan; Lim, Changwoo; Hong, Jiyoung; Lee, Soogab

    2010-02-01

    An experimental study was performed to compare the annoyances from civil-aircraft noise, military-aircraft noise, railway noise, and road-traffic noise. Two-way within-subjects designs were applied in this research. Fifty-two subjects, who were naive listeners, were given various stimuli with varying levels through a headphone in an anechoic chamber. Regardless of the frequency weighting network, even under the same average energy level, civil-aircraft noise was the most annoying, followed by military-aircraft noise, railway noise, and road-traffic noise. In particular, penalties in the time-averaged, A-weighted sound level (TAL) of about 8, 5, and 5 dB, respectively, were found in the civil-aircraft, military-aircraft, and railway noises. The reason could be clarified through the high-frequency component and the variability in the level. When people were exposed to sounds with the same maximum A-weighted level, a railway bonus of about 3 dB was found. However, transportation noise has been evaluated by the time-averaged A-weighted level in most countries. Therefore, in the present situation, the railway bonus is not acceptable for railway vehicles with diesel-electric engines.

  6. Noise sensitivity in relation to baseline arousal, physiological response and psychological features to noise exposure during task performance

    NARCIS (Netherlands)

    White, K.; Hofman, W.F.; van Kamp, I.

    2010-01-01

    People who consider themselves sensitive to noise, experience more noise annoyance, sleep disturbance and reduced daytime performance. Besides psychological factors, an association with cardiovascular reactions during noise has been established in noise sensitives. Decreased efficiency of the parasy

  7. Jet Noise Diagnostics Supporting Statistical Noise Prediction Methods

    Science.gov (United States)

    Bridges, James E.

    2006-01-01

    The primary focus of my presentation is the development of the jet noise prediction code JeNo with most examples coming from the experimental work that drove the theoretical development and validation. JeNo is a statistical jet noise prediction code, based upon the Lilley acoustic analogy. Our approach uses time-average 2-D or 3-D mean and turbulent statistics of the flow as input. The output is source distributions and spectral directivity. NASA has been investing in development of statistical jet noise prediction tools because these seem to fit the middle ground that allows enough flexibility and fidelity for jet noise source diagnostics while having reasonable computational requirements. These tools rely on Reynolds-averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) solutions as input for computing far-field spectral directivity using an acoustic analogy. There are many ways acoustic analogies can be created, each with a series of assumptions and models, many often taken unknowingly. And the resulting prediction can be easily reverse-engineered by altering the models contained within. However, only an approach which is mathematically sound, with assumptions validated and modeled quantities checked against direct measurement will give consistently correct answers. Many quantities are modeled in acoustic analogies precisely because they have been impossible to measure or calculate, making this requirement a difficult task. The NASA team has spent considerable effort identifying all the assumptions and models used to take the Navier-Stokes equations to the point of a statistical calculation via an acoustic analogy very similar to that proposed by Lilley. Assumptions have been identified and experiments have been developed to test these assumptions. In some cases this has resulted in assumptions being changed. Beginning with the CFD used as input to the acoustic analogy, models for turbulence closure used in RANS CFD codes have been explored and

  8. Noise exposure among construction electricians.

    Science.gov (United States)

    Seixas, N S; Ren, K; Neitzel, R; Camp, J; Yost, M

    2001-01-01

    Data-logging noise dosimetry was used to assess the exposure levels of electricians working for a major electrical subcontractor in Washington State at five sites using four types of construction methods. Subjects documented activities and work environment information throughout their work shift, resulting in an activity/exposure record for each of the 174 full-shift samples collected over the 4-month duration of the study. Over 24% of the TWA samples exceeded 85 dBA; 5.2% exceeded the federal Occupational Safety and Health Administration permissible exposure limit of 90 dBA. The National Institute for Occupational Safety and Health exposure metric, which specifies a 3-dB ER, was also utilized; using this metric, 67.8% of the samples exceeded 85 dBA and 27% exceeded 90 dBA. Subjects were directly observed for a subset of 4469 min during which more detailed activity and environmental information was recorded. Linear and logistic regression models using this subset were used to identify the determinants of average exposure, and exposure exceedences, respectively. These models demonstrated the importance of multiple variable modeling in interpreting exposure assessments, and the feasibility and utility of modeling exposure exceedences using logistic regression. The results further showed that presumably quiet trades such as electrician are at risk of exposure to potentially harmful noise exposures, and that other workers' activities and the general environment contribute substantially to that risk. These results indicate that noise control strategies will have to address the construction work environment as an integrated system.

  9. Noise reduction of spiral ducts.

    Science.gov (United States)

    Lapka, Wojciech; Cempel, Czesław

    2007-01-01

    The paper presents noise reduction (NR) of spiral ducts as a result of computational modeling of acoustic wave propagation. Three-dimensional models were created with the finite element method in COMSOL Multiphysics version 3.3. Nine models of spiral ducts with 1-9 spiral leads were considered. Time-harmonic analysis was used to predict NR, which was shown in spectral and interval frequency bands. Spiral duct performance can be seen as a comparison of NR before and after a change from a circular to a spiral duct.

  10. Noise and dynamical pattern selection

    CERN Document Server

    Kurtze, D A

    1995-01-01

    In pattern forming systems such as Rayleigh-Benard convection or directional solidification, a large number of linearly stable, patterned steady states exist when the basic, simple steady state is unstable. Which of these steady states will be realized in a given experiment appears to depend on unobservable details of the system's initial conditions. We show, however, that weak, Gaussian white noise drives such a system toward a preferred wave number which depends only on the system parameters and is independent of initial conditions. We give a prescription for calculating this wave number, analytically near the onset of instability and numerically otherwise.

  11. On noise limited cellular networks

    CERN Document Server

    Decreusefond, Laurent; Vu, Thanh-Tung

    2010-01-01

    This paper introduces a general theoretical framework to analyze noise limited networks. More precisely, we consider two homogenous Poisson point processes of base stations and users. General model of radio signal propagation and effect of fading are also considered. The main difference of our model with respect to other existing models is that a user connects to his best servers but not necessarily the closest one. We provide general formula for the outage probability. We study functionals related to the SNR as well as the sum of these functionals over all users per cell. For the latter, the expectation and bounds on the variance are obtained.

  12. ”Sound [signal] noise

    DEFF Research Database (Denmark)

    Bjørnsten, Thomas

    2012-01-01

    has been paid to, for instance, a category such as ‘sound art’ together with an equally strengthened interest in phenomena and concepts that fall outside the accepted aesthetic procedures and constructions of what we traditionally would term as musical sound – a recurring example being ‘noise’.......The article discusses the intricate relationship between sound and signification through notions of noise. The emergence of new fields of sonic artistic practices has generated several questions of how to approach sound as aesthetic form and material. During the past decade an increased attention...

  13. Flap Edge Noise Reduction Fins

    Science.gov (United States)

    Khorrami, Mehdi R. (Inventor); Choudhan, Meelan M. (Inventor)

    2015-01-01

    A flap of the type that is movably connected to an aircraft wing to provide control of an aircraft in flight includes opposite ends, wherein at least a first opposite end includes a plurality of substantially rigid, laterally extending protrusions that are spaced apart to form a plurality of fluidly interconnected passageways. The passageways have openings adjacent to upper and lower sides of the flap, and the passageways include a plurality of bends such that high pressure fluid flows from a high pressure region to a low pressure region to provide a boundary condition that inhibits noise resulting from airflow around the end of the flap.

  14. Coupling of a core post-translational pacemaker to a slave transcription/translation feedback loop in a circadian system.

    Directory of Open Access Journals (Sweden)

    Ximing Qin

    Full Text Available Cyanobacteria are the only model circadian clock system in which a circadian oscillator can be reconstituted in vitro. The underlying circadian mechanism appears to comprise two subcomponents: a post-translational oscillator (PTO and a transcriptional/translational feedback loop (TTFL. The PTO and TTFL have been hypothesized to operate as dual oscillator systems in cyanobacteria. However, we find that they have a definite hierarchical interdependency-the PTO is the core pacemaker while the TTFL is a slave oscillator that quickly damps when the PTO stops. By analysis of overexpression experiments and mutant clock proteins, we find that the circadian system is dependent upon the PTO and that suppression of the PTO leads to damped TTFL-based oscillations whose temperature compensation is not stable under different metabolic conditions. Mathematical modeling indicates that the experimental data are compatible with a core PTO driving the TTFL; the combined PTO/TTFL system is resilient to noise. Moreover, the modeling indicates a mechanism by which the TTFL can feed into the PTO such that new synthesis of clock proteins can phase-shift or entrain the core PTO pacemaker. This prediction was experimentally tested and confirmed by entraining the in vivo circadian system with cycles of new clock protein synthesis that modulate the phosphorylation status of the clock proteins in the PTO. In cyanobacteria, the PTO is the self-sustained core pacemaker that can operate independently of the TTFL, but the TTFL damps when the phosphorylation status of the PTO is clamped. However, the TTFL can provide entraining input into the PTO. This study is the first to our knowledge to experimentally and theoretically investigate the dynamics of a circadian clock in which a PTO is coupled to a TTFL. These results have important implications for eukaryotic clock systems in that they can explain how a TTFL could appear to be a core circadian clockwork when in fact the true

  15. Kurtosis corrected sound pressure level as a noise metric for risk assessment of occupational noises.

    Science.gov (United States)

    Goley, G Steven; Song, Won Joon; Kim, Jay H

    2011-03-01

    Current noise guidelines use an energy-based noise metric to predict the risk of hearing loss, and thus ignore the effect of temporal characteristics of the noise. The practice is widely considered to underestimate the risk of a complex noise environment, where impulsive noises are embedded in a steady-state noise. A basic form for noise metrics is designed by combining the equivalent sound pressure level (SPL) and a temporal correction term defined as a function of kurtosis of the noise. Several noise metrics are developed by varying this basic form and evaluated utilizing existing chinchilla noise exposure data. It is shown that the kurtosis correction term significantly improves the correlation of the noise metric with the measured hearing losses in chinchillas. The average SPL of the frequency components of the noise that define the hearing loss with a kurtosis correction term is identified as the best noise metric among tested. One of the investigated metrics, the kurtosis-corrected A-weighted SPL, is applied to a human exposure study data as a preview of applying the metrics to human guidelines. The possibility of applying the noise metrics to human guidelines is discussed.

  16. Restoration for Noise Removal in Quantum Images

    Science.gov (United States)

    Liu, Kai; Zhang, Yi; Lu, Kai; Wang, Xiaoping

    2017-09-01

    Quantum computation has become increasingly attractive in the past few decades due to its extraordinary performance. As a result, some studies focusing on image representation and processing via quantum mechanics have been done. However, few of them have considered the quantum operations for images restoration. To address this problem, three noise removal algorithms are proposed in this paper based on the novel enhanced quantum representation model, oriented to two kinds of noise pollution (Salt-and-Pepper noise and Gaussian noise). For the first algorithm Q-Mean, it is designed to remove the Salt-and-Pepper noise. The noise points are extracted through comparisons with the adjacent pixel values, after which the restoration operation is finished by mean filtering. As for the second method Q-Gauss, a special mask is applied to weaken the Gaussian noise pollution. The third algorithm Q-Adapt is effective for the source image containing unknown noise. The type of noise can be judged through the quantum statistic operations for the color value of the whole image, and then different noise removal algorithms are used to conduct image restoration respectively. Performance analysis reveals that our methods can offer high restoration quality and achieve significant speedup through inherent parallelism of quantum computation.

  17. Supersonic Jet Noise Reduction Using Microjets

    Science.gov (United States)

    Gutmark, Ephraim; Cuppoletti, Dan; Malla, Bhupatindra

    2013-11-01

    Fluidic injection for jet noise reduction involves injecting secondary jets into a primary jet to alter the noise characteristics of the primary jet. A major challenge has been determining what mechanisms are responsible for noise reduction due to varying injector designs, injection parameters, and primary jets. The current study provides conclusive results on the effect of injector angle and momentum ux ratio on the acoustics and shock structure of a supersonic Md = 1.56 jet. It is shown that the turbulent mixing noise scales primarily with the injector momentum flux ratio. Increasing the injector momentum flux ratio increases streamwise vorticity generation and reduces peak turbulence levels. It is found that the shock-related noise components are most affected by the interaction of the shocks from the injectors with the primary shock structure of the jet. Increasing momentum flux ratio causes shock noise reduction until a limit where shock noise increases again. It is shown that the shock noise components and mixing noise components are reduced through fundamentally different mechanisms and maximum overall noise reduction is achieved by balancing the reduction of both components.

  18. The Low Noise Limit in Gene Expression.

    Directory of Open Access Journals (Sweden)

    Roy D Dar

    Full Text Available Protein noise measurements are increasingly used to elucidate biophysical parameters. Unfortunately noise analyses are often at odds with directly measured parameters. Here we show that these inconsistencies arise from two problematic analytical choices: (i the assumption that protein translation rate is invariant for different proteins of different abundances, which has inadvertently led to (ii the assumption that a large constitutive extrinsic noise sets the low noise limit in gene expression. While growing evidence suggests that transcriptional bursting may set the low noise limit, variability in translational bursting has been largely ignored. We show that genome-wide systematic variation in translational efficiency can-and in the case of E. coli does-control the low noise limit in gene expression. Therefore constitutive extrinsic noise is small and only plays a role in the absence of a systematic variation in translational efficiency. These results show the existence of two distinct expression noise patterns: (1 a global noise floor uniformly imposed on all genes by expression bursting; and (2 high noise distributed to only a select group of genes.

  19. Modeling and Prediction of Krueger Device Noise

    Science.gov (United States)

    Guo, Yueping; Burley, Casey L.; Thomas, Russell H.

    2016-01-01

    This paper presents the development of a noise prediction model for aircraft Krueger flap devices that are considered as alternatives to leading edge slotted slats. The prediction model decomposes the total Krueger noise into four components, generated by the unsteady flows, respectively, in the cove under the pressure side surface of the Krueger, in the gap between the Krueger trailing edge and the main wing, around the brackets supporting the Krueger device, and around the cavity on the lower side of the main wing. For each noise component, the modeling follows a physics-based approach that aims at capturing the dominant noise-generating features in the flow and developing correlations between the noise and the flow parameters that control the noise generation processes. The far field noise is modeled using each of the four noise component's respective spectral functions, far field directivities, Mach number dependencies, component amplitudes, and other parametric trends. Preliminary validations are carried out by using small scale experimental data, and two applications are discussed; one for conventional aircraft and the other for advanced configurations. The former focuses on the parametric trends of Krueger noise on design parameters, while the latter reveals its importance in relation to other airframe noise components.

  20. Air injection vacuum blower noise control

    Energy Technology Data Exchange (ETDEWEB)

    Mose, Tyler L.A.; Faszer, Andrew C. [Noise Solutions Inc. (Canada)], email: tmose@noisesolutions.com, email: afaszer@noisesolutions.com

    2011-07-01

    Air injection vacuum blowers, with applications in waste removal, central vacuum systems, and aeration systems, are widely used when high vacuum levels are required. Noise generated by those blowers must be addressed for operator health and residential disturbance. This paper describes a project led by Noise Solutions Inc., to identify noise sources in a blower, and design and test a noise mitigation system. First the predominant noise sources in the blower must be determined, this is done with a sound level meter used to quantify the contribution of each individual noise source and the dominant tonal noise from the blower. Design of a noise abatement system must take into account constraints arising from blower mobile use, blower optimal performance, and the resulting overall vibration of the structure. The design was based on calculations from the sound attenuation of a reactive expansion chamber and two prototypes of custom silencers were then tested, showing a significant noise reduction both in total sound levels and tonal noise.

  1. Noise suppression in surface microseismic data

    Science.gov (United States)

    Forghani-Arani, Farnoush; Batzle, Mike; Behura, Jyoti; Willis, Mark; Haines, Seth S.; Davidson, Michael

    2012-01-01

    We introduce a passive noise suppression technique, based on the τ − p transform. In the τ − p domain, one can separate microseismic events from surface noise based on distinct characteristics that are not visible in the time-offset domain. By applying the inverse τ − p transform to the separated microseismic event, we suppress the surface noise in the data. Our technique significantly improves the signal-to-noise ratios of the microseismic events and is superior to existing techniques for passive noise suppression in the sense that it preserves the waveform. We introduce a passive noise suppression technique, based on the τ − p transform. In the τ − p domain, one can separate microseismic events from surface noise based on distinct characteristics that are not visible in the time-offset domain. By applying the inverse τ − p transform to the separated microseismic event, we suppress the surface noise in the data. Our technique significantly improves the signal-to-noise ratios of the microseismic events and is superior to existing techniques for passive noise suppression in the sense that it preserves the waveform.

  2. Examining nocturnal railway noise and aircraft noise in the field: sleep, psychomotor performance, and annoyance.

    Science.gov (United States)

    Elmenhorst, Eva-Maria; Pennig, Sibylle; Rolny, Vinzent; Quehl, Julia; Mueller, Uwe; Maaß, Hartmut; Basner, Mathias

    2012-05-01

    Traffic noise is interfering during day- and nighttime causing distress and adverse physiological reactions in large parts of the population. Railway noise proved less annoying than aircraft noise in surveys which were the bases for a so called 5 dB railway bonus regarding noise protection in many European countries. The present field study investigated railway noise-induced awakenings during sleep, nighttime annoyance and the impact on performance the following day. Comparing these results with those from a field study on aircraft noise allowed for a ranking of traffic modes concerning physiological and psychological reactions. 33 participants (mean age 36.2 years ± 10.3 (SD); 22 females) living alongside railway tracks around Cologne/Bonn (Germany) were polysomnographically investigated. These data were pooled with data from a field study on aircraft noise (61 subjects) directly comparing the effects of railway and aircraft noise in one random subject effects logistic regression model. Annoyance was rated in the morning evaluating the previous night. Probability of sleep stage changes to wake/S1 from railway noise increased significantly from 6.5% at 35 dB(A) to 20.5% at 80 dB(A) LAFmax. Rise time of noise events had a significant impact on awakening probability. Nocturnal railway noise led to significantly higher awakening probabilities than aircraft noise, partly explained by the different rise times, whereas the order was inversed for annoyance. Freight train noise compared to passenger train noise proved to have the most impact on awakening probability. Nocturnal railway noise had no effect on psychomotor vigilance. Nocturnal freight train noise exposure in Germany was associated with increased awakening probabilities exceeding those for aircraft noise and contrasting the findings of many annoyance surveys and annoyance ratings of our study. During nighttime a bonus for railway noise seems not appropriate. Copyright © 2012 Elsevier B.V. All rights reserved.

  3. Definition of 1992 Technology Aircraft Noise Levels and the Methodology for Assessing Airplane Noise Impact of Component Noise Reduction Concepts

    Science.gov (United States)

    Kumasaka, Henry A.; Martinez, Michael M.; Weir, Donald S.

    1996-01-01

    This report describes the methodology for assessing the impact of component noise reduction on total airplane system noise. The methodology is intended to be applied to the results of individual study elements of the NASA-Advanced Subsonic Technology (AST) Noise Reduction Program, which will address the development of noise reduction concepts for specific components. Program progress will be assessed in terms of noise reduction achieved, relative to baseline levels representative of 1992 technology airplane/engine design and performance. In this report, the 1992 technology reference levels are defined for assessment models based on four airplane sizes - an average business jet and three commercial transports: a small twin, a medium sized twin, and a large quad. Study results indicate that component changes defined as program final goals for nacelle treatment and engine/airframe source noise reduction would achieve from 6-7 EPNdB reduction of total airplane noise at FAR 36 Stage 3 noise certification conditions for all of the airplane noise assessment models.

  4. Low-frequency-noise complaints

    DEFF Research Database (Denmark)

    Pedersen, Christian Sejer; Møller, Henrik; Persson-Waye, Kerstin

    2008-01-01

    From 203 cases of low-frequency complaints a random selection of twenty-one cases were investigated. The main aim of the investigation was to answer the question whether the annoyance is caused by an external physical sound or by a physically non-existing sound, i.e. low-frequency tinnitus. Noise...... of the complainants are annoyed by a physical sound (20-180 Hz), while others suffer from low-frequency tinnitus (perceived frequency 40-100 Hz). Physical sound at frequencies below 20 Hz (infrasound) is not responsible for the annoyance - or at all audible - in any of the investigated cases, and none...... of the complainants has extraordinary hearing sensitivity at low frequencies. For comparable cases of low-frequency noise complaints in general, it is anticipated that physical sound is responsible in a substantial part of the cases, while low-frequency tinnitus is responsible in another substantial part of the cases....

  5. 1/f Noise Outperforms White Noise in Sensitizing Baroreflex Function in the Human Brain

    Science.gov (United States)

    Soma, Rika; Nozaki, Daichi; Kwak, Shin; Yamamoto, Yoshiharu

    2003-08-01

    We show that externally added 1/f noise more effectively sensitizes the baroreflex centers in the human brain than white noise. We examined the compensatory heart rate response to a weak periodic signal introduced via venous blood pressure receptors while adding 1/f or white noise with the same variance to the brain stem through bilateral cutaneous stimulation of the vestibular afferents. In both cases, this noisy galvanic vestibular stimulation optimized covariance between the weak input signals and the heart rate responses. However, the optimal level with 1/f noise was significantly lower than with white noise, suggesting a functional benefit of 1/f noise for neuronal information transfer in the brain.

  6. Elimination of noise peak for signal processing in Johnson noise thermometry development

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, I. G.; Moon, B. S.; Jeong, J. E.; Jeo, Y. H. [KAERI, Taejon (Korea, Republic of); Kisner, Roger A. [Oak Ridge National Lab., Oak Ridge (United States)

    2003-10-01

    The internal and external noise is the most considering obstacle in development of Johnson Noise Thermometry system. This paper addresses an external noise elimination issue of the Johnson Noise Thermometry system which is underway of development in collaboration between KAERI and ORNL. Although internal random noise is canceled by Cross Power Spectral Density function, a continuous wave penetrating into the electronic circuit is eliminated by the difference of peaks between Johnson signal and external noise. The elimination logic using standard deviation of CPSD and energy leakage problem in discrete CPSD function are discussed in this paper.

  7. Optical signal to noise ratio improvement through unbalanced noise beating in phase-sensitive parametric amplifiers.

    Science.gov (United States)

    Malik, R; Kumpera, A; Olsson, S L I; Andrekson, P A; Karlsson, M

    2014-05-05

    We investigate the beating of signal and idler waves, which have imbalanced signal to noise ratios, in a phase-sensitive parametric amplifier. Imbalanced signal to noise ratios are achieved in two ways; first by imbalanced noise loading; second by varying idler to signal input power ratio. In the case of imbalanced noise loading the phase-sensitive amplifier improved the signal to noise ratio from 3 to 6 dB, and in the case of varying idler to signal input power ratio, the signal to noise ratio improved from 3 to in excess of 20 dB.

  8. Noise, errors and information in quantum amplification

    CERN Document Server

    D'Ariano, G M; Maccone, L

    1997-01-01

    We analyze and compare the characterization of a quantum device in terms of noise, transmitted bit-error-rate (BER) and mutual information, showing how the noise description is meaningful only for Gaussian channels. After reviewing the description of a quantum communication channel, we study the insertion of an amplifier. We focus attention on the case of direct detection, where the linear amplifier has a 3 decibels noise figure, which is usually considered an unsurpassable limit, referred to as the standard quantum limit (SQL). Both noise and BER could be reduced using an ideal amplifier, which is feasible in principle. However, just a reduction of noise beyond the SQL does not generally correspond to an improvement of the BER or of the mutual information. This is the case of a laser amplifier, where saturation can greatly reduce the noise figure, although there is no corresponding improvement of the BER. Such mechanism is illustrated on the basis of Monte Carlo simulations.

  9. Noise filtering via electromagnetically induced transparency

    Science.gov (United States)

    Jeong, Taek; Bae, In-Ho; Moon, Han Seb

    2017-01-01

    We report on the intensity-noise reduction of pseudo-thermal light via electromagnetically induced transparency (EIT) in the Λ-type system of the 5S1/2-5P1/2 transition in 87Rb. Noise filtering of the pseudo-thermal probe light was achieved via an EIT filter and measured according to the degree of intensity noise of the pseudo-thermal probe light. Reductions in the intensity and spectral noise of the pseudo-thermal probe light with the EIT filter were observed using the direct intensity fluctuation and heterodyne detection technique, respectively. Comparison of the intensity noise of the pseudo-thermal probe light before and after passing through the EIT filter revealed a significant reduction in the intensity noise.

  10. Noise Properties of CMOS Current Conveyors

    DEFF Research Database (Denmark)

    Bruun, Erik

    1996-01-01

    The definition of the current conveyor is presented and it is shown how different generations of current conveyors can all be combined into a single definition of a multiple-output second generation current conveyor (CCII). Next, noise sources are introduced into the model, and a general noise...... model for the current conveyor is established. This model is used for the analysis of selected examples of current conveyor based operational amplifier configurations and the relative merits with respect to the noise performance of these configurations are discussed. Finally, the noise model...... is developed for a CMOS current conveyor implementation, and optimization strategies for noise reduction are discussed. It is concluded that a class AB implementation provides more flexibility than does a class A configuration. In both cases it is essential to design low noise current mirrors and current...

  11. Aviation Noise Impacts: State of the Science

    Science.gov (United States)

    Basner, Mathias; Clark, Charlotte; Hansell, Anna; Hileman, James I.; Janssen, Sabine; Shepherd, Kevin; Sparrow, Victor

    2017-01-01

    Noise is defined as “unwanted sound.” Aircraft noise is one, if not the most detrimental environmental effect of aviation. It can cause community annoyance, disrupt sleep, adversely affect academic performance of children, and could increase the risk for cardiovascular disease of people living in the vicinity of airports. In some airports, noise constrains air traffic growth. This consensus paper was prepared by the Impacts of Science Group of the Committee for Aviation Environmental Protection of the International Civil Aviation Organization and summarizes the state of the science of noise effects research in the areas of noise measurement and prediction, community annoyance, children’s learning, sleep disturbance, and health. It also briefly discusses civilian supersonic aircraft as a future source of aviation noise.

  12. Noise in Advanced Electronic Devices and Circuits

    Science.gov (United States)

    Deen, M. Jamal; Marinov, O.

    2005-08-01

    State-of-the-art low-frequency and high-frequency noise performance and modeling in modern semiconductor devices and circuits are discussed. The increase of noise-to-DC current ratio may compromise the circuit applications in near future. The low-frequency noise (LFN) tends to a log-normal distribution. Since the random-telegraph-signal (RTS) noise is pronounced in submicron devices, then new techniques being used to characterize of multilevel RTS are discussed. High-frequency noise modeling and sample experimental results are presented, including the important effect of gate-tunneling current for future devices. For the RF circuits, we discuss the phase noise in voltage-controlled oscillators (VCO) based on ring oscillators and LC-tank VCOs with and without automatic amplitude control. Finally, the effects of hot-carrier stress on the performance of a VCO is presented and discussed.

  13. Noise measurement in total knee arthroplasty

    Directory of Open Access Journals (Sweden)

    Lukas A Holzer

    2014-01-01

    Full Text Available Few studies have been performed to analyze noise levels produced by various surgical instruments in the operating room (OR. The highest levels of noise that have been described were due to instruments used for total knee arthroplasty (TKA. These high levels of noise might be a potential health hazard for patients and medical staff. Therefore, we aimed to measure noise levels of current instruments that are widely used worldwide. During a conventional primary TKA the levels of noise in the OR were measured using a Class 1 integrating-averaging sound level meter. The highest A-weighted equivalent level was produced when using a hammer during the implantation of the femoral and tibial components with 90.2 dBA. In total surgical instruments were used for about 10% of the total time of surgery. Noise exposure due to instrument use during TKA does not seem to be a potential health hazard for medical staff or patients.

  14. Complex diffusion process for noise reduction

    DEFF Research Database (Denmark)

    Nadernejad, Ehsan; Barari, A.

    2014-01-01

    Signal de-noising and restoration is an essential step for many signal processing algorithms and applications. One of the most common problems is the removal of some interesting structures in the signal during the restoration process. The capability of methods based on partial differential...... equations (PDEs) in image restoration and de-noising prompted many researchers to search for an improvement in the technique. In this paper, a new method is presented for signal de-noising, based on PDEs and Schrodinger equations, named as complex diffusion process (CDP). This method assumes that variations...... for signal de-noising. To evaluate the performance of the proposed method, a number of experiments have been performed using Sinusoid, multi-component and FM signals cluttered with noise. The results indicate that the proposed method outperforms the approaches for signal de-noising known in prior art....

  15. Cardiovascular effects of environmental noise exposure.

    Science.gov (United States)

    Münzel, Thomas; Gori, Tommaso; Babisch, Wolfgang; Basner, Mathias

    2014-04-01

    The role of noise as an environmental pollutant and its impact on health are being increasingly recognized. Beyond its effects on the auditory system, noise causes annoyance and disturbs sleep, and it impairs cognitive performance. Furthermore, evidence from epidemiologic studies demonstrates that environmental noise is associated with an increased incidence of arterial hypertension, myocardial infarction, and stroke. Both observational and experimental studies indicate that in particular night-time noise can cause disruptions of sleep structure, vegetative arousals (e.g. increases of blood pressure and heart rate) and increases in stress hormone levels and oxidative stress, which in turn may result in endothelial dysfunction and arterial hypertension. This review focuses on the cardiovascular consequences of environmental noise exposure and stresses the importance of noise mitigation strategies for public health.

  16. Asymptotics of high order noise corrections

    CERN Document Server

    Sondergaard, N; Pálla, G; Voros, A; Sondergaard, Niels; Vattay, Gabor; Palla, Gergely; Voros, Andre

    1999-01-01

    We consider an evolution operator for a discrete Langevin equation with a strongly hyperbolic classical dynamics and noise with finite moments. Using a perturbative expansion of the evolution operator we calculate high order corrections to its trace in the case of a quartic map and Gaussian noise. The leading contributions come from the period one orbits of the map. The asymptotic behaviour is investigated and is found to be independent up to a multiplicative constant of the distribution of noise.

  17. Phase Noise Reduction of Laser Diode

    Science.gov (United States)

    Zhang, T. C.; Poizat, J.-Ph.; Grelu, P.; Roch, J.-F.; Grangier, P.; Marin, F.; Bramati, A.; Jost, V.; Levenson, M. D.; Giacobino, E.

    1996-01-01

    Phase noise of single mode laser diodes, either free-running or using line narrowing technique at room temperature, namely injection-locking, has been investigated. It is shown that free-running diodes exhibit very large excess phase noise, typically more than 80 dB above shot-noise at 10 MHz, which can be significantly reduced by the above-mentioned technique.

  18. Constrained crosstalk resistant adaptive noise canceller

    Science.gov (United States)

    Parsa, V.; Parker, P.

    1994-08-01

    The performance of an adaptive noise canceller (ANC) is sensitive to the presence of signal `crosstalk' in the reference channel. The authors propose a novel approach to crosstalk resistant adaptive noise cancellation, namely the constrained crosstalk resistant adaptive noise canceller (CCRANC). The theoretical analysis of the CCRANC along with the constrained algorithm is presented. The performance of the CCRANC in recovering somatosensory evoked potentials (SEPs) from myoelectric interference is then evaluated through simulations.

  19. Measurement of the beauty of periodic noises

    CERN Document Server

    Manet, Vincent

    2012-01-01

    In this article indicators to describe the "beauty" of noises are proposed. Rhythmic, tonal and harmonic suavity are introduced. They give a characterization of a noise in terms of rhythmic regularity (rhythmic suavity), of auditory pleasure of the "chords" constituting the signal (tonal suavity) and of the transition between the chords (harmonic suavity). These indicators have been developed for periodic noises typically issued from rotating machines such as engines, compressors... and are now used by our industrial customers since two years.

  20. Signal and Noise in 3D Environments

    Science.gov (United States)

    2015-09-30

    1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Signal and Noise in 3D Environments Michael B. Porter...complicated 3D environments . I have also been doing a great deal of work in modeling the noise field (the ocean soundscape) due to various sources...we have emphasized the propagation of ‘signals’. We have become increasingly interested in modeling ‘ noise ’ which can illuminate the ocean environment

  1. Noise environment reduction foam spheres in space

    Science.gov (United States)

    Scharton, Terry; Kern, Dennis; Badilla, Gloria

    1989-01-01

    The advent of lightweight fairings for new spacecraft and the increased thrust of new launch vehicles have intensified the need for better techniques for predicting and for reducing the low frequency noise environment of spacecraft at liftoff. This paper presents a VAPEPS (VibroAcoustic Payload Environment Prediction System) parametrical analysis of the noise reduction of spacecraft fairings and explores a novel technique for increasing the low frequency noise reduction of lightweight fairing by approximately 10 dB.

  2. Shot noise in linear macroscopic resistors

    OpenAIRE

    Gomila Lluch, Gabriel; Pennetta, C.; Reggiani, L.; Ferrari, G; Sampietro, M.; G. Bertuccio(Politecnico di Milano, Italy)

    2004-01-01

    We report on direct experimental evidence of shot noise in a linear macroscopic resistor. The origin of the shot noise comes from the fluctuation of the total number of charge carriers inside the resistor associated with their diffusive motion under the condition that the dielectric relaxation time becomes longer than the dynamic transit time. The present results show that neither potential barriers nor the absence of inelastic scattering are necessary to observe shot noise in electronic devi...

  3. Shot Noise in Linear Macroscopic Resistors

    Science.gov (United States)

    Gomila, G.; Pennetta, C.; Reggiani, L.; Sampietro, M.; Ferrari, G.; Bertuccio, G.

    2004-06-01

    We report on direct experimental evidence of shot noise in a linear macroscopic resistor. The origin of the shot noise comes from the fluctuation of the total number of charge carriers inside the resistor associated with their diffusive motion under the condition that the dielectric relaxation time becomes longer than the dynamic transit time. The present results show that neither potential barriers nor the absence of inelastic scattering are necessary to observe shot noise in electronic devices.

  4. Noise gates for decoherent quantum circuits

    OpenAIRE

    Bassi, Angelo; Deckert, D. -A.

    2008-01-01

    A major problem in exploiting microscopic systems for developing a new technology based on the principles of Quantum Information is the influence of noise which tends to work against the quantum features of such systems. It becomes then crucial to understand how noise affects the evolution of quantum circuits: several techniques have been proposed among which stochastic differential equations (SDEs) can represent a very convenient tool. We show how SDEs naturally map any Markovian noise into ...

  5. Modulated Entanglement Evolution Via Correlated Noises

    CERN Document Server

    Corn, Brittany

    2009-01-01

    We study entanglement dynamics in the presence of correlated environmental noises. Specifically, we investigate the quantum entanglement dynamics of two spins in the presence of correlated classical white noises, deriving Markov master equation and obtaining explicit solutions for several interesting classes of initial states including Bell states and X form density matrices. We show how entanglement can be enhanced or reduced by the correlation between the two participating noises.

  6. Road-Traffic Noise: Annoyance, Risk Perception, and Noise Sensitivity in the Finnish Adult Population

    Directory of Open Access Journals (Sweden)

    Enembe Oku Okokon

    2015-05-01

    Full Text Available Exposure to road-traffic noise commonly engenders annoyance, the extent of which is determined by factors not fully understood. Our aim was to estimate the prevalence and determinants of road-traffic noise annoyance and noise sensitivity in the Finnish adult population, while comparing the perceptions of road-traffic noise to exhausts as environmental health problems. Using a questionnaire that yielded responses from 1112 randomly selected adult Finnish respondents, we estimated road-traffic noise- and exhausts-related perceived exposures, health-risk perceptions, and self-reported annoyance on five-point scales, while noise sensitivity estimates were based on four questions. Determinants of noise annoyance and sensitivity were investigated using multivariate binary logistic regression and linear regression models, respectively. High or extreme noise annoyance was reported by 17% of respondents. Noise sensitivity scores approximated a Gaussian distribution. Road-traffic noise and exhausts were, respectively, considered high or extreme population-health risks by 22% and 27% of respondents. Knowledge of health risks from traffic noise, OR: 2.04 (1.09–3.82 and noise sensitivity, OR: 1.07 (1.00–1.14 were positively associated with annoyance. Knowledge of health risks (p < 0.045 and positive environmental attitudes (p < 000 were associated with higher noise sensitivity. Age and sex were associated with annoyance and sensitivity only in bivariate models. A considerable proportion of Finnish adults are highly annoyed by road-traffic noise, and perceive it to be a significant health risk, almost comparable to traffic exhausts. There is no distinct noise-sensitive population subgroup. Knowledge of health risks of road-traffic noise, and attitudinal variables are associated with noise annoyance and sensitivity.

  7. Diameter dependence of 1/f noise in carbon nanotube field effect transistors using noise spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Kawahara, Toshio, E-mail: toshi@isc.chubu.ac.jp [Center of Applied Superconductivity and Sustainable Energy Research, Chubu University, 1200, Matsumoto-cho, Kasugai-shi, Aichi 487-8501 (Japan); Yamaguchi, Satarou [Center of Applied Superconductivity and Sustainable Energy Research, Chubu University, 1200, Matsumoto-cho, Kasugai-shi, Aichi 487-8501 (Japan); Ohno, Yasuhide; Maehashi, Kenzo; Matsumoto, Kazuhiko [The Institute of Scientific and Industrial Research, Osaka University, 8-1, Mihogaoka, Ibaraki, Osaka 567-0047 (Japan); Mizutani, Shin [NTT Communication Science Laboratories, 2-4, Hikaridai Seika-cho, Soraku-gun, Kyoto 619-0237 (Japan); Itaka, Kenji [North Japan Research Institute for Sustainable Energy, Hirosaki University, 2-1-3 Matsubara, Aomori 030-0813 (Japan)

    2013-02-15

    Carbon nanotubes (CNTs) have many interesting properties for nano devices such as high sensitive sensors or noise enhanced nonlinear devices. A field effect transistor (FET) structure is one of the key features for these applications, and the control of noise in FETs is important for the actual operation of the application. Several origins of noise have been proposed, and defects and/or surface adsorption of molecules seem to be dominant for the 1/f type noise in CNTs. To study the origins of noise, the diameter dependence of noise properties was studied. We analyzed the noise properties in CNTs using noise spectroscopy with different fabrication parameters or ambient environments. We observed the crossover of noise properties in CNTs, which involved transition between different origins of noise depending on their diameter. Additionally, noise spectroscopy was used to observe such crossover between air and vacuum environments. We can control noise intensity using the gate voltage, and noise properties can be controlled by the fabrication parameters. These phenomena are useful for the stochastic operation of CNT-FETs.

  8. Identification and Reduction of Turbomachinery Noise Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Noise has become a primary consideration in the design and development of many products, particulary in aerospace, automotive and consumer product industries....

  9. An overview of health effects on noise

    Science.gov (United States)

    Osada, Y.

    1988-12-01

    Although noise can damage the inner ear and cause other pathological changes, its most common negative effects are non-somatic, such as a perception of noisiness and disturbance of daily activities. According to the definition of health by WHO, this should be considered as a health hazard. These health effects of noise can be classified into the following three categories: (I) hearing loss, perception of noisiness and masking are produced along the auditory pathway and are thus direct and specific effects of noise; (II) interference with performance, rest and sleep, a feeling of discomfort and some physiological effects are produced as indirect and non-specific effects via reticular formation of the midbrain; (III) annoyance is not merely a feeling of unpleasantness but the feeling of being bothered or troubled, and includes the development of a particular attitude toward the noise source. Individual or group behavioral responses will be evoked when annoyance develops. Annoyance and behavioral response are integrated and composite effects. The health effects of noise are modified by many factors related to both the noise and the individual. Noise level, frequency spectrum, duration and impulsiveness modify the effects. Sex, age, health status and mental character also have an influence on the effects. Direct effects of noise are most dependent on the physical nature of the noise and least dependent on human factors. Indirect effects are more dependent, and integrated effects most dependent, on human factors.

  10. Environmental noise and human prenatal growth

    Energy Technology Data Exchange (ETDEWEB)

    Schell, L.M.

    1981-09-01

    To determine whether chronic exposure to relatively loud noise has demonstrable biological effects in humans, a study was conducted on the effect of mother's exposure to airport noise while pregnant, and of social and biological characteristics of the family upon birthweight and gestation length. The sample of births was drawn from a community located adjacent to an international airport in the U.S., where noise levels had been measured previously. Mother's noise exposure was based upon noise levels near her residence in the community while she was pregnant. Data from 115 births were used, these being from mothers whose noise exposure history was most complete throughout the pregnancy. Using multivariate analysis to correct for family characteristics, the partial correlation coefficient for noise exposure and gestation length was negative, large, and significant in girls (r . -0.49, p less than 0.001). In boys the partial correlation coefficient was also negative but was smaller and did not quite reach statistical significance. Partial correlations with birthweight were smaller in both boys and girls and not significant. These results agree best with previous studies that suggest that noise may reduce prenatal growth. The size of the observed effects may be related to a conservative research design biased towards underestimation, as well as to the real effects of noise upon human prenatal growth.

  11. Hybrid Analysis of Engine Core Noise

    Science.gov (United States)

    O'Brien, Jeffrey; Kim, Jeonglae; Ihme, Matthias

    2015-11-01

    Core noise, or the noise generated within an aircraft engine, is becoming an increasing concern for the aviation industry as other noise sources are progressively reduced. The prediction of core noise generation and propagation is especially challenging for computationalists since it involves extensive multiphysics including chemical reaction and moving blades in addition to the aerothermochemical effects of heated jets. In this work, a representative engine flow path is constructed using experimentally verified geometries to simulate the physics of core noise. A combustor, single-stage turbine, nozzle and jet are modeled in separate calculations using appropriate high fidelity techniques including LES, actuator disk theory and Ffowcs-Williams Hawkings surfaces. A one way coupling procedure is developed for passing fluctuations downstream through the flowpath. This method effectively isolates the core noise from other acoustic sources, enables straightforward study of the interaction between core noise and jet exhaust, and allows for simple distinction between direct and indirect noise. The impact of core noise on the farfield jet acoustics is studied extensively and the relative efficiency of different disturbance types and shapes is examined in detail.

  12. Enhanced Core Noise Modeling for Turbofan Engines

    Science.gov (United States)

    Stone, James R.; Krejsa, Eugene A.; Clark, Bruce J.

    2011-01-01

    This report describes work performed by MTC Technologies (MTCT) for NASA Glenn Research Center (GRC) under Contract NAS3-00178, Task Order No. 15. MTCT previously developed a first-generation empirical model that correlates the core/combustion noise of four GE engines, the CF6, CF34, CFM56, and GE90 for General Electric (GE) under Contract No. 200-1X-14W53048, in support of GRC Contract NAS3-01135. MTCT has demonstrated in earlier noise modeling efforts that the improvement of predictive modeling is greatly enhanced by an iterative approach, so in support of NASA's Quiet Aircraft Technology Project, GRC sponsored this effort to improve the model. Since the noise data available for correlation are total engine noise spectra, it is total engine noise that must be predicted. Since the scope of this effort was not sufficient to explore fan and turbine noise, the most meaningful comparisons must be restricted to frequencies below the blade passage frequency. Below the blade passage frequency and at relatively high power settings jet noise is expected to be the dominant source, and comparisons are shown that demonstrate the accuracy of the jet noise model recently developed by MTCT for NASA under Contract NAS3-00178, Task Order No. 10. At lower power settings the core noise became most apparent, and these data corrected for the contribution of jet noise were then used to establish the characteristics of core noise. There is clearly more than one spectral range where core noise is evident, so the spectral approach developed by von Glahn and Krejsa in 1982 wherein four spectral regions overlap, was used in the GE effort. Further analysis indicates that the two higher frequency components, which are often somewhat masked by turbomachinery noise, can be treated as one component, and it is on that basis that the current model is formulated. The frequency scaling relationships are improved and are now based on combustor and core nozzle geometries. In conjunction with the Task

  13. A noise-controlled dynamic bifurcation

    CERN Document Server

    Lythe, G D

    1997-01-01

    We consider a slow passage through a point of loss of stability. If the passage is sufficiently slow, the dynamics are controlled by additive random disturbances, even if they are extremely small. We derive expressions for the `exit value' distribution when the parameter is explicitly a function of time and the dynamics are controlled by additive Gaussian noise. We derive a new expression for the small correction introduced if the noise is coloured (exponentially correlated). There is good agreement with results obtained from simulation of sample paths of the appropriate stochastic differential equations. Multiplicative noise does not produce noise-controlled dynamics in this fashion.

  14. Voltage fluctuations in neurons: signal or noise?

    DEFF Research Database (Denmark)

    Yarom, Yosef; Hounsgaard, Jorn

    2011-01-01

    , we discuss noise-free neuronal signaling and detrimental and beneficial forms of noise in large-scale functional neural networks. Evidence that noise and variability in some cases go hand in hand with behavioral variability and increase behavioral choice, richness, and adaptability opens new avenues...... that allows and facilitates complex adaptive behavior in an unpredictable world. Here we review the growing experimental evidence that functional network activity is associated with intense fluctuations in membrane potential and spike timing. We trace origins and consequences of noise and variability. Finally...

  15. Pump Cavitation Noise Estimation from Acceleration Signals

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Do Hwan; Ha, Che Woong [KHNP Central Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    The cavitation noise can be measured directly by using pressure sensing devices. However, penetration of pipes or pump casings is inevitable to install the devices. This increases the risk of leaks. In an effort to reduce that risk, a cavitation noise estimation model based on vibration signals has been proposed. In the present study, the applicability of cavitation noise estimation methods including the previously proposed model is investigated. In order to assess the severity of cavitation, the cavitation noise estimation is necessary. In the present study, the cavitation noise is estimated by using acceleration signals measured outside of pumps and the theory of the statistical energy analysis. The applicability and limit of the cavitation noise estimation from the acceleration signals are examined by comparing the cavitation noise obtained from the pressure signal. The results suggest that the acoustic cavitation inception can be detected by the cavitation noise estimation from acceleration signals. The accuracy of the cavitation noise estimates is highly dependent on the locations of the pump casing that accelerometers attached on and the cut-off frequency of high pass filtering.

  16. Tools for noise characterization in Virgo

    Energy Technology Data Exchange (ETDEWEB)

    Accadia, T; Belletoile, A [Laboratoire d' Annecy-le-Vieux de Physique des Particules (LAPP), IN2P3/CNRS, Universite de Savoie, F-74941 Annecy-le-Vieux (France); Ballardin, G [European Gravitational Observatory (EGO), I-56021 Cascina (PI) (Italy); Barsuglia, M; Bouhou, B [AstroParticule et Cosmologie (APC), CNRS: UMR7164-IN2P3-Observatoire de Paris-Universite Denis Diderot-Paris 7 - CEA : DSM/IRFU (France); Bonnand, R [Laboratoire des Materiaux Avances (LMA), IN2P3/CNRS, F-69622 Villeurbanne, Lyon (France); Acernese, F; Antonucci, F; Astone, P; Barone, F; Bauer, Th S; Beker, M G; Birindelli, S; Bitossi, M; Bizouard, M A; Blom, M; Bondu, F; Bonelli, L; Boschi, V; Bosi, L, E-mail: elena.cuoco@ego-gw.i

    2010-08-01

    Several software tools were used to perform on-line and of-line noise analysis as a support to commissioning activities, to monitor the rate of glitches, the occurrence of non stationary noise, the presence of environmental contamination, the behavior of narrow spectral features and the coherence with auxiliary channels. We report about the use of these tools to study the main sources of identified noise: broadband, spectral lines and glitches. Plans for the upgrade of the tools will be presented, for example for lines identification purpose to let the scientists in control room do noise characterization in an easier way.

  17. Helicopter internal noise control: Three case histories

    Science.gov (United States)

    Edwards, B. D.; Cox, C. R.

    1978-01-01

    Case histories are described in which measurable improvements in the cabin noise environments of the Bell 214B, 206B, and 222 were realized. These case histories trace the noise control efforts followed in each vehicle. Among the design approaches considered, the addition of a fluid pulsation damper in a hydraulic system and the installation of elastomeric engine mounts are highlighted. It is concluded that substantial weight savings result when the major interior noise sources are controlled by design, both in altering the noise producing mechanism and interrupting the sound transmission paths.

  18. Better Faster Noise with the GPU

    DEFF Research Database (Denmark)

    Wyvill, Geoff; Frisvad, Jeppe Revall

    Filtered noise [Perlin 1985] has, for twenty years, been a fundamental tool for creating functional texture and it has many other applications; for example, animating water waves or the motion of grass waving in the wind. Perlin noise suffers from a number of defects and there have been many atte...... attempts to create better or faster noise but Perlin’s ‘Gradient Noise’ has consistently proved to be the best compromise between speed and quality. Our objective was to create a better noise cheaply by use of the GPU....

  19. The Negative Affect Hypothesis of Noise Sensitivity

    Directory of Open Access Journals (Sweden)

    Daniel Shepherd

    2015-05-01

    Full Text Available Some studies indicate that noise sensitivity is explained by negative affect, a dispositional tendency to negatively evaluate situations and the self. Individuals high in such traits may report a greater sensitivity to other sensory stimuli, such as smell, bright light and pain. However, research investigating the relationship between noise sensitivity and sensitivity to stimuli associated with other sensory modalities has not always supported the notion of a common underlying trait, such as negative affect, driving them. Additionally, other explanations of noise sensitivity based on cognitive processes have existed in the clinical literature for over 50 years. Here, we report on secondary analyses of pre-existing laboratory (n = 74 and epidemiological (n = 1005 data focusing on the relationship between noise sensitivity to and annoyance with a variety of olfactory-related stimuli. In the first study a correlational design examined the relationships between noise sensitivity, noise annoyance, and perceptual ratings of 16 odors. The second study sought differences between mean noise and air pollution annoyance scores across noise sensitivity categories. Results from both analyses failed to support the notion that, by itself, negative affectivity explains sensitivity to noise.

  20. Signal processing in noise waveform radar

    CERN Document Server

    Kulpa, Krzysztof

    2013-01-01

    This book is devoted to the emerging technology of noise waveform radar and its signal processing aspects. It is a new kind of radar, which use noise-like waveform to illuminate the target. The book includes an introduction to basic radar theory, starting from classical pulse radar, signal compression, and wave radar. The book then discusses the properties, difficulties and potential of noise radar systems, primarily for low-power and short-range civil applications. The contribution of modern signal processing techniques to making noise radar practical are emphasized, and application examples

  1. Using entanglement against noise in quantum metrology.

    Science.gov (United States)

    Demkowicz-Dobrzański, Rafal; Maccone, Lorenzo

    2014-12-19

    We analyze the role of entanglement among probes and with external ancillas in quantum metrology. In the absence of noise, it is known that unentangled sequential strategies can achieve the same Heisenberg scaling of entangled strategies and that external ancillas are useless. This changes in the presence of noise; here we prove that entangled strategies can have higher precision than unentangled ones and that the addition of passive external ancillas can also increase the precision. We analyze some specific noise models and use the results to conjecture a general hierarchy for quantum metrology strategies in the presence of noise.

  2. Noise exposures in US coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Seiler, J.P.; Valoski, M.P.; Crivaro, M.A.

    1994-05-01

    Mine Safety and Health Administration (MSHA) inspectors conduct full-shift environmental noise surveys to determine the occupational noise levels to which coal miners are exposed. These noise surveys are performed to determine compliance with the noise standard promulgated under the Federal Mine Safety and Health Act of 1977. Data from over 60,000 full-shift noise surveys conducted from fiscal year 1986 through 1992 were entered into a computer data base to facilitate analysis. This paper presents the mean and standard deviation of over 60,000 full-shift noise dose measurements for various underground and surface coal mining occupations. Additionally, it compares and contrasts the levels with historical noise exposure measurements for selected coal mining occupations that were published in the 1970`s. The findings were that the percentage of miners surveyed that were subjected to noise exposures above 100%, neglecting personal hearing protectors, were 26.5% and 21.6% for surface and underground mining, respectively. Generally, the trend is that the noise exposures for selected occupations have decreased since the 1970`s.

  3. Charge Noise in Organic Electrochemical Transistors

    Science.gov (United States)

    Stoop, Ralph L.; Thodkar, Kishan; Sessolo, Michele; Bolink, Henk J.; Schönenberger, Christian; Calame, Michel

    2017-01-01

    Organic electrochemical transistors (OECTs) are increasingly studied as transducers in sensing applications. While much emphasis has been placed on analyzing and maximizing the OECT signal, noise has been mostly ignored, although it determines the resolution of the sensor. The major contribution to the noise in sensing devices is the 1 /f noise, dominant at low frequency. In this work, we demonstrate that the 1 /f noise in OECTs follows a charge-noise model, which reveals that the noise is due to charge fluctuations in proximity or within the bulk of the channel material. We present the noise scaling behavior with gate voltage, channel dimensions, and polymer thickness. Our results suggest the use of large area channels in order to maximize the signal-to-noise ratio (SNR) for biochemical and electrostatic sensing applications. A comparison with the literature shows that the magnitude of the noise in OECTs is similar to that observed in graphene transistors, and only slightly higher than that found in carbon nanotubes and silicon nanowire devices. In a model ion-sensing experiment with OECTs, we estimate crucial parameters such as the characteristic SNR and the corresponding limit of detection.

  4. Research on Emerging and Descending Aircraft Noise

    Directory of Open Access Journals (Sweden)

    Monika Bartkevičiūtė

    2013-12-01

    Full Text Available Along with an increase in the aircraft engine power and growth in air traffic, noise level at airports and their surrounding environs significantly increases. Aircraft noise is high level noise spreading within large radius and intensively irritating the human body. Air transport is one of the main sources of noise having a particularly strong negative impact on the environment. The article deals with activities and noises taking place in the largest nationwide Vilnius International Airport.The level of noise and its dispersion was evaluated conducting research on the noise generated by emerging and descending aircrafts in National Vilnius Airport. Investigation was carried out at 2 measuring points located in a residential area. There are different types of aircrafts causing different sound levels. It has been estimated the largest exceedances that occur when an aircraft is approaching. In this case, the noisiest types of aircrafts are B733, B738 and AT72. The sound level varies from 70 to 85 dBA. The quietest aircrafts are RJ1H and F70. When taking off, the equivalent of the maximum sound level value of these aircrafts does not exceed the authorized limits. The paper describes the causes of noise in aircrafts, the sources of origin and the impact of noise on humans and the environment.Article in Lithuanian

  5. Formant discrimination in noise for isolated vowels

    Science.gov (United States)

    Liu, Chang; Kewley-Port, Diane

    2004-11-01

    Formant discrimination for isolated vowels presented in noise was investigated for normal-hearing listeners. Discrimination thresholds for F1 and F2, for the seven American English vowels /eye, smcapi, eh, æ, invv, aye, you/, were measured under two types of noise, long-term speech-shaped noise (LTSS) and multitalker babble, and also under quiet listening conditions. Signal-to-noise ratios (SNR) varied from -4 to +4 dB in steps of 2 dB. All three factors, formant frequency, signal-to-noise ratio, and noise type, had significant effects on vowel formant discrimination. Significant interactions among the three factors showed that threshold-frequency functions depended on SNR and noise type. The thresholds at the lowest levels of SNR were highly elevated by a factor of about 3 compared to those in quiet. The masking functions (threshold vs SNR) were well described by a negative exponential over F1 and F2 for both LTSS and babble noise. Speech-shaped noise was a slightly more effective masker than multitalker babble, presumably reflecting small benefits (1.5 dB) due to the temporal variation of the babble. .

  6. Teratogenic effects of noise in mice

    Science.gov (United States)

    Murata, M.; Takigawa, H.

    1989-07-01

    This study was undertaken to assess the hazardous effects of noise on embryonic development. The experiment was composed of two parts; one was the observation of the effect due to noise alone, and the other was the observation of the combined effect of noise and known teratogens. ICR mice were exposed to a wide octave-band noise at 100 dB(C) for 6 hours a day in three ways: the first group was exposed to a continuous noise only on day 7 of pregnancy (group "N"), the second was exposed to an intermittent noise (15 min ON/15 min OFF) only on day 7 of pregnancy (group "IN"), and the third was exposed daily to a continuous noise during days 7-12 of pregnancy (group "RN"). Cadmium sulfate or trypan blue was applied as a teratogen, and was administered intraperitoneously on day 7 of pregnancy. On day 18 of pregnancy, mice were sacrificed and the developmental status and external malformations of their fetuses were examined. Each type of noise exposure did not significantly induce embryolethality and fetal growth retardation. However, teratogenicity was observed in groups "N" and "IN". Combined effects of teratogen and noise did not show clear-cut interactions.

  7. Selection of noise parameters for Kalman filter

    Institute of Scientific and Technical Information of China (English)

    Ka-Veng Yuen; Ka-In Hoi; Kai-Meng Mok

    2007-01-01

    The Bayesian probabilistic approach is proposed to estimate the process noise and measurement noise parameters for a Kalman filter. With state vectors and covariance matrices estimated by the Kalman filter, the likehood of the measurements can be constructed as a function of the process noise and measurement noise parameters. By maximizing the likklihood function with respect to these noise parameters, the optimal values can be obtained. Furthermore, the Bayesian probabilistic approach allows the associated uncertainty to be quantified. Examples using a single-degree-of-freedom system and a ten-story building illustrate the proposed method. The effect on the performance of the Kalman filter due to the selection of the process noise and measurement noise parameters was demonstrated. The optimal values of the noise parameters were found to be close to the actual values in the sense that the actual parameters were in the region with significant probability density. Through these examples, the Bayesian approach was shown to have the capability to provide accurate estimates of the noise parameters of the Kalman filter, and hence for state estimation.

  8. Quantum noise property in coherent atomic system

    Institute of Scientific and Technical Information of China (English)

    ZHANG Jun-xiang; WANG Hai-hong; CAI Jin; GAO Jiang-rui

    2006-01-01

    The coherent superposition of atomic states leads to the characteristic change of interacting lights because of the coupling between the lights and atoms.In this paper,the noise spectrum of the quantified light interacting with the atoms is studied under the condition of electromagnetically induced transparency (EIT).It is shown that the noise spectrum displays a double M-shape noise profile resulted from the conversion of phase noise of probe beam.A squeezing of 0.3 dB can be observed at the detuning of probe light at the proper parameters of atoms and coupling beam.

  9. Noises in Detecting Relic Gravitational Wave

    Institute of Scientific and Technical Information of China (English)

    LEE Zhi-Jun; WAN Zhen-Zhu

    2006-01-01

    We analyse the three basic kinds of noises in detecting the relic gravitational wave (GW), which are the noises caused by the thermal radiation in the detecting cavity and by the scattering of the Gaussian beam in the detecting cavity, and noise in the microwave radiometers. The analysis shows that a reasonable signal-to-noise ratio may be achieved for a detecting device with a suitable geometric structure only when the temperature of the environment is no more than T = 0.6 K, and the power of the radiation of the Gaussian beam is no less than P = 105W.

  10. Random signals and noise a mathematical introduction

    CERN Document Server

    Engelberg, Shlomo

    2011-01-01

    Understanding the nature of random signals and noise is critically important for detecting signals and for reducing and minimizing the effects of noise in applications such as communications and control systems. Outlining a variety of techniques and explaining when and how to use them, Random Signals and Noise: A Mathematical Introduction focuses on applications and practical problem solving rather than probability theory.A Firm FoundationBefore launching into the particulars of random signals and noise, the author outlines the elements of probability that are used throughout the book and incl

  11. The application of active noise control technology to reduce noise from air pollution control equipment

    Energy Technology Data Exchange (ETDEWEB)

    Depies, C. R.; Kapsos, D. W.

    1996-08-01

    The basic concept of active noise control, i. e. to create a noise field in a space in order to destructively interfere with an existing noise, and in the process create a quieter space, was explained. The manner in which noise control technology can be used in air pollution control equipment was described and guidelines for application were provided. A number of case studies were used to illustrate the suitability of active noise control for low frequency noise problems, especially in the area of air pollution control equipment. Impressive reduction of low frequency noise, energy efficiency, ability to retrofit into an existing duct system, and the hardware`s insensitivity to dirty exhaust environments were cited as the principal reasons for the success of active noise control technology over more traditional in-line passive silencers. 1 ref., 8 figs.

  12. Stochastic resonance in linear system driven by multiplicative noise and additive quadratic noise

    Institute of Scientific and Technical Information of China (English)

    Ning Li-Juan; Xu Wei; Yao Ming-Li

    2007-01-01

    In this paper the stochastic resonance (SR) is studied in an overdamped linear system driven by multiplicative noise and additive quadratic noise. The exact expressions are obtained for the first two moments and the correlation function by using linear response and the properties of the dichotomous noise. SR phenomenon exhibits in the linear system. There are three different forms of SR: the bona fide SR, the conventional SR and SR in the broad sense.Moreover, the effect of the asymmetry of the multiplicative noise on the signal-to-noise ratio (SNR) is different from that of the additive noise and the effect of multiplicative noise and additive noise on SNR is different.

  13. Intrinsic Noise Level of Noise Cross-Correlation Functions and its Implication to Source Population of Ambient noises

    Science.gov (United States)

    Chen, Ying-Nien; Gung, Yuancheng; Chiao, Ling-Yun; Rhie, Junkee

    2017-01-01

    SUMMARYWe present a quantitative procedure to evaluate the intrinsic noise level (INL) of the noise cross-correlation function (NCF). The method is applied to realistic NCFs derived from the continuous data recorded by the seismic arrays in Taiwan and Korea. The obtained temporal evolution of NCF noise level follows fairly the prediction of the theoretical formulation, confirming the feasibility of the method. We then apply the obtained INL to the assessment of data quality and the source characteristics of ambient noise. We show that the INL-based signal-to-noise ratio provides an exact measure for the true noise level within the NCF and better resolving power for the NCF quality, and such measurement can be implemented to any time windows of the NCFs to evaluate the quality of overtones or coda waves. Moreover, since NCF amplitudes are influenced by both the population and excitation strengths of noises, while INL is primarily sensitive to the overall source population, with information from both measurements, we may better constrain the source characteristics of seismic ambient noises.

  14. Neutron Noise Measurement at CROCUS

    Energy Technology Data Exchange (ETDEWEB)

    Roland, V.; Perret, G. [Paul Scherrer Institut, Villigen (Switzerland); Girardin, G.; Frajtag, P.; Pautz, A. [Laboratory for Reactor Physics and Systems Behaviour, Lausanne (Switzerland)

    2013-07-01

    This paper reports on the measurements of kinetics parameters at the teaching reactor CROCUS. The prompt decay constant, |α| = (β-ρ)/Λ, was measured in several sub-critical configurations using the Feynman-α reactor noise technique and the reduced generation time Λ/β was deduced. The CROCUS facility is a zero-power reactor operated at EPFL. It is mainly used for educational purposes. Among all neutron noise measurement techniques, the focus was put on the Feynman-α technique. The intrinsic neutron population fluctuations were recorded in macroscopically stable sub-critical states and the prompt decay constants α were derived by fitting the Feynman-α experimental distributions with the point kinetic theoretical expression. The prompt decay constant at critical state α{sub 0}=β/Λ was deduced in two ways: by extrapolation of the sub-critical prompt decay constant to the critical state, and by direct measurement of the sub-critical reactivity using rod-drop techniques. The neutron population was measured by two BF{sub 3} detectors located in the reactor. Data acquisition was performed simultaneously with two ORTEC multichannel scaler cards (MCS-pci) controlled by specially developed LabView programs. The post-processing of the data was done in LabView and Matlab. The prompt decay constant (β/Λ) at criticality was found to be 146.6 ± 6.3 s{sup -1}. Monte Carlo predictions calculated with MCNP5-1.6 are in a good agreement being within 2σ of the experimental results.

  15. Full noise characterization of a low-noise two-stage SQUID amplifier

    Energy Technology Data Exchange (ETDEWEB)

    Falferi, P [Istituto di Fotonica e Nanotecnologie, CNR-Fondazione Bruno Kessler, 38100 Povo, Trento (Italy); Mezzena, R [INFN, Gruppo Collegato di Trento, Sezione di Padova, 38100 Povo, Trento (Italy); Vinante, A [INFN, Sezione di Padova, 35131 Padova (Italy)], E-mail: falferi@science.unitn.it

    2009-07-15

    From measurements performed on a low-noise two-stage SQUID amplifier coupled to a high- Q electrical resonator we give a complete noise characterization of the SQUID amplifier around the resonator frequency of 11 kHz in terms of additive, back action and cross-correlation noise spectral densities. The minimum noise temperature evaluated at 135 mK is 10 {mu}K and corresponds to an energy resolution of 18{Dirac_h}.

  16. Road-traffic noise: annoyance, risk perception, and noise sensitivity in the Finnish adult population.

    Science.gov (United States)

    Okokon, Enembe Oku; Turunen, Anu W; Ung-Lanki, Sari; Vartiainen, Anna-Kaisa; Tiittanen, Pekka; Lanki, Timo

    2015-05-26

    Exposure to road-traffic noise commonly engenders annoyance, the extent of which is determined by factors not fully understood. Our aim was to estimate the prevalence and determinants of road-traffic noise annoyance and noise sensitivity in the Finnish adult population, while comparing the perceptions of road-traffic noise to exhausts as environmental health problems. Using a questionnaire that yielded responses from 1112 randomly selected adult Finnish respondents, we estimated road-traffic noise- and exhausts-related perceived exposures, health-risk perceptions, and self-reported annoyance on five-point scales, while noise sensitivity estimates were based on four questions. Determinants of noise annoyance and sensitivity were investigated using multivariate binary logistic regression and linear regression models, respectively. High or extreme noise annoyance was reported by 17% of respondents. Noise sensitivity scores approximated a Gaussian distribution. Road-traffic noise and exhausts were, respectively, considered high or extreme population-health risks by 22% and 27% of respondents. Knowledge of health risks from traffic noise, OR: 2.04 (1.09-3.82) and noise sensitivity, OR: 1.07 (1.00-1.14) were positively associated with annoyance. Knowledge of health risks (pnoise sensitivity. Age and sex were associated with annoyance and sensitivity only in bivariate models. A considerable proportion of Finnish adults are highly annoyed by road-traffic noise, and perceive it to be a significant health risk, almost comparable to traffic exhausts. There is no distinct noise-sensitive population subgroup. Knowledge of health risks of road-traffic noise, and attitudinal variables are associated with noise annoyance and sensitivity.

  17. Evaluation of Noise Control Technology and Alternative Noise Certification Procedures for Propeller-Driven Small Airplanes.

    Science.gov (United States)

    1982-05-01

    Lower Noise Levels for Turboprop Aircraft vs Piston Engine Aircraft. .. .... .... 52 15 Carpet Plots Relating Noise Level, Propeller Diameter...and empiricized the so-called "vortex noise" which occurred at higher frequencies. It was rapidly found that these guidelines were totally inadequate...blade rotational tip Mach number. Various attempts have been made to rationalize the relationships between A- weighted noise level, propeller blade tip

  18. Phase Noise Influence in Optical OFDM Systems employing RF Pilot Tone for Phase Noise Cancellation

    OpenAIRE

    Jacobsen, Gunnar; Kazovsky, Leonid G.; Xu, TianHua; Popov, Sergei; Li, Jie; Zhang, Yimo; Friberg, Ari T.

    2016-01-01

    For coherent and direct-detection Orthogonal Frequency Division Multiplexed (OFDM) systems employing radio frequency (RF) pilot tone phase noise cancellation the influence of laser phase noise is evaluated. Novel analytical results for the common phase error and for the (modulation dependent) inter carrier interference are evaluated based upon Gaussian statistics for the laser phase noise. In the evaluation it is accounted for that the laser phase noise is filtered in the correlation signal d...

  19. Towards Full-Waveform Ambient Noise Inversion

    Science.gov (United States)

    Sager, Korbinian; Ermert, Laura; Afanasiev, Michael; Boehm, Christian; Fichtner, Andreas

    2017-04-01

    Noise tomography usually works under the assumption that the inter-station ambient noise correlation is equal to a scaled version of the Green function between the two receivers. This assumption, however, is only met under specific conditions, e.g. wavefield diffusivity and equipartitioning, or the isotropic distribution of both mono- and dipolar uncorrelated noise sources. These assumptions are typically not satisfied in the Earth. This inconsistency inhibits the exploitation of the full waveform information contained in noise correlations in order to constrain Earth structure and noise generation. To overcome this limitation, we attempt to develop a method that consistently accounts for the distribution of noise sources, 3D heterogeneous Earth structure and the full seismic wave propagation physics. This is intended to improve the resolution of tomographic images, to refine noise source distribution, and thereby to contribute to a better understanding of both Earth structure and noise generation. First, we develop an inversion strategy based on a 2D finite-difference code using adjoint techniques. To enable a joint inversion for noise sources and Earth structure, we investigate the following aspects: i) the capability of different misfit functionals to image wave speed anomalies and source distribution and ii) possible source-structure trade-offs, especially to what extent unresolvable structure can be mapped into the inverted noise source distribution and vice versa. In anticipation of real-data applications, we present an extension of the open-source waveform modelling and inversion package Salvus (http://salvus.io). It allows us to compute correlation functions in 3D media with heterogeneous noise sources at the surface and the corresponding sensitivity kernels for the distribution of noise sources and Earth structure. By studying the effect of noise sources on correlation functions in 3D, we validate the aforementioned inversion strategy and prepare the

  20. Neural Control Adaptation to Motor Noise Manipulation

    Directory of Open Access Journals (Sweden)

    Christopher J Hasson

    2016-03-01

    Full Text Available Antagonistic muscular co-activation can compensate for movement variability induced by motor noise at the expense of increased energetic costs. Greater antagonistic co-activation is commonly observed in older adults, which could be an adaptation to increased motor noise. The present study tested this hypothesis by manipulating motor noise in twelve young subjects while they practiced a goal-directed task using a myoelectric virtual arm, which was controlled by their biceps and triceps muscle activity. Motor noise was increased by increasing the coefficient of variation of the myoelectric signals. As hypothesized, subjects adapted by increasing antagonistic co-activation, and this was associated with reduced noise-induced performance decrements. A second hypothesis was that a virtual decrease in motor noise, achieved by smoothing the myoelectric signals, would have the opposite effect: co-activation would decrease and motor performance would improve. However, the results showed that a decrease in noise made performance worse instead of better, with no change in co-activation. Overall, these findings suggest that the nervous system adapts to virtual increases in motor noise by increasing antagonistic co-activation, and this preserves motor performance. Reducing noise may have failed to benefit performance due to characteristics of the filtering process itself, e.g. delays are introduced and muscle activity bursts are attenuated. The observed adaptations to increased noise may explain in part why older adults and many patient populations have greater antagonistic co-activation, which could represent an adaptation to increased motor noise, along with a desire for increased joint stability.

  1. White noise theory of robust nonlinear filtering with correlated state and observation noises

    NARCIS (Netherlands)

    Bagchi, Arunabha; Karandikar, Rajeeva

    1994-01-01

    In the existing `direct¿ white noise theory of nonlinear filtering, the state process is still modelled as a Markov process satisfying an Itô stochastic differential equation, while a `finitely additive¿ white noise is used to model the observation noise. We remove this asymmetry by modelling the st

  2. White noise theory of robust nonlinear filtering with correlated state and observation noises

    NARCIS (Netherlands)

    Bagchi, Arunabha; Karandikar, Rajeeva

    1992-01-01

    In the direct white noise theory of nonlinear filtering, the state process is still modeled as a Markov process satisfying an Ito stochastic differential equation, while a finitely additive white noise is used to model the observation noise. In the present work, this asymmetry is removed by modeling

  3. Binaural Integrated Active Noise Control and Noise Reduction in Hearing Aids

    DEFF Research Database (Denmark)

    Serizel, Romain; Moonen, Marc; Wouters, Jan;

    2013-01-01

    This paper presents a binaural approach to integrated active noise control and noise reduction in hearing aids and aims at demonstrating that a binaural setup indeed provides significant advantages in terms of the number of noise sources that can be compensated for and in terms of the causality...

  4. Effects of transportation noise and attitudes on noise annoyance and task performance

    NARCIS (Netherlands)

    White, K.; Meeter, M.; Bronkhorst, A.

    2012-01-01

    In this study, effects on task performance and annoyance by aircraft and road traffic noise and attitudes towards these noise sources were addressed in a lab-setting. On day 1 of the study, participants performed a 3-back working memory task in silence and with noise samples played over a headphone

  5. Noise Pollution in Turkish Elementary Schools: Evaluation of Noise Pollution Awareness and Sensitivity Training

    Science.gov (United States)

    Bulunuz, Nermin

    2014-01-01

    This study investigates noise pollution levels in two elementary schools. Also, "noise level awareness and sensitivity training" was given for reducing noise pollution, and the effects and results of this training were evaluated. "Sensitivity" training was given to 611 students and 48 teachers in a private and a public school.…

  6. Intrinsic 1/f device noise reduction and its effect on phase noise in CMOS ring oscillators

    NARCIS (Netherlands)

    Gierkink, Sander L.J.; Klumperink, Eric A.M.; Wel, van der Arnoud P.; Hoogzaad, Gian; Tuijl, van Ed (A.J.M.); Nauta, Bram

    1999-01-01

    This paper gives experimental proof of an intriguing physical effect: periodic on-off switching of MOS transistors in a CMOS ring oscillator reduces their intrinsic 1/f noise and hence the oscillator's close-in phase noise. More specifically, it is shown that the 1/f3 phase noise is dependent on the

  7. Low voltage excess noise and shot noise in YBCO bicrystal junctions

    DEFF Research Database (Denmark)

    Constantinian, K.Y.; Ovsyannikov, G.A.; Borisenko, I.V.;

    2002-01-01

    The spectral density of background noise emitted by symmetric bicrystal YBaCuO Josephson junctions on sapphire substrates have been measured by a low noise cooled HEMT amplifier for bias voltages up to V approximate to 50 mV. At relatively low voltages V <4 mV a noticeable noise rise has been reg...

  8. A measurement model for general noise reaction in response to aircraft noise

    NARCIS (Netherlands)

    Kroesen, M.; Schreckenberg, D.

    2011-01-01

    In this paper a measurement model for general noise reaction (GNR) in response to aircraft noise is developed to assess the performance of aircraft noise annoyance and a direct measure of general reaction as indicators of this concept. For this purpose GNR is conceptualized as a superordinate latent

  9. Some new viewpoints in reactor noise analysis

    Institute of Scientific and Technical Information of China (English)

    罗征培; 李富; 等

    1996-01-01

    It is propsed that the linearity criterion and order criterion via frequency spectrum features without any limitation of the model's phase can be used in reactor noise analysis.The time constant,natural frequency as well as the recovered transfer function of reactors can bhe obtained via the analyzable model based on reactor noise.

  10. White Noise Path Integrals in Stochastic Neurodynamics

    Science.gov (United States)

    Carpio-Bernido, M. Victoria; Bernido, Christopher C.

    2008-06-01

    The white noise path integral approach is used in stochastic modeling of neural activity, where the primary dynamical variables are the relative membrane potentials, while information on transmembrane ionic currents is contained in the drift coefficient. The white noise path integral allows a natural framework and can be evaluated explicitly to yield a closed form for the conditional probability density.

  11. Improved measurement methods for railway rolling noise

    NARCIS (Netherlands)

    Dittrich, M.G.; Janssens, M.H.A.

    2000-01-01

    Some of the issues related to railway noise type testing are discussed and potential improvements to existing procedures are put forward. New and improved methods that also go beyond the scope of type testing are presented that help to characterize and analyze rolling noise more accurately. These

  12. Reducing Noise in a College Library.

    Science.gov (United States)

    Luyben, Paul D.; And Others

    1981-01-01

    Discusses an experiment on controlling library noise by rearrangement of furniture groupings and the separation of existing clusters of furniture. While electromechanical tests showed no significant differences, user measures indicated more acceptable noise levels. There are numerous illustrations and 30 references. (RAA)

  13. Quantum noise-induced chaotic oscillations

    OpenAIRE

    Bag, Bidhan Chandra; Ray, Deb Shankar

    1999-01-01

    We examine the weak quantum noise limit of Wigner equation for phase space distribution functions. It has been shown that the leading order quantum noise described in terms of an auxiliary Hamiltonian manifests itself as an additional fluctuational degree of freedom which may induce chaotic and regular oscillations in a nonlinear oscillator.

  14. Quantum noise-induced chaotic oscillations

    CERN Document Server

    Bag, B C; Bag, Bidhan Chandra; Ray, Deb Shankar

    1999-01-01

    We examine the weak quantum noise limit of Wigner equation for phase space distribution functions. It has been shown that the leading order quantum noise described in terms of an auxilliary Hamiltonian manifests itself as an additional fluctuational degree of freedom which may induce chaotic and regular oscillations in a nonlinear oscillator.

  15. Current Noise Spectrum of a Quantum Shuttle

    DEFF Research Database (Denmark)

    Flindt, Christian; Novotny, T.; Jauho, Antti-Pekka

    2005-01-01

    We present a method for calculating the full current noise spectrum S(omega) for the class of nano-electromechanical systems (NEMS) that can be described by a Markovian generalized master equation. As a specific example we apply the method to a quantum shuttle. The noise spectrum of the shuttle h...

  16. Road traffic noise and incident myocardial infarction

    DEFF Research Database (Denmark)

    Sørensen, Mette; Andersen, Zorana Jovanovic; Nordsborg, Rikke B;

    2012-01-01

    Both road traffic noise and ambient air pollution have been associated with risk for ischemic heart disease, but only few inconsistent studies include both exposures.......Both road traffic noise and ambient air pollution have been associated with risk for ischemic heart disease, but only few inconsistent studies include both exposures....

  17. Underwater noise levels in UK waters

    Science.gov (United States)

    Merchant, Nathan D.; Brookes, Kate L.; Faulkner, Rebecca C.; Bicknell, Anthony W. J.; Godley, Brendan J.; Witt, Matthew J.

    2016-11-01

    Underwater noise from human activities appears to be rising, with ramifications for acoustically sensitive marine organisms and the functioning of marine ecosystems. Policymakers are beginning to address the risk of ecological impact, but are constrained by a lack of data on current and historic noise levels. Here, we present the first nationally coordinated effort to quantify underwater noise levels, in support of UK policy objectives under the EU Marine Strategy Framework Directive (MSFD). Field measurements were made during 2013-2014 at twelve sites around the UK. Median noise levels ranged from 81.5-95.5 dB re 1 μPa for one-third octave bands from 63-500 Hz. Noise exposure varied considerably, with little anthropogenic influence at the Celtic Sea site, to several North Sea sites with persistent vessel noise. Comparison of acoustic metrics found that the RMS level (conventionally used to represent the mean) was highly skewed by outliers, exceeding the 97th percentile at some frequencies. We conclude that environmental indicators of anthropogenic noise should instead use percentiles, to ensure statistical robustness. Power analysis indicated that at least three decades of continuous monitoring would be required to detect trends of similar magnitude to historic rises in noise levels observed in the Northeast Pacific.

  18. 14 CFR 36.501 - Noise limits.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Noise limits. 36.501 Section 36.501..., Commuter Category Airplanes § 36.501 Noise limits. (a) Compliance with this subpart must be shown for— (1... applicable limit set in Part D of appendix F. (c) For aircraft covered by this subpart for...

  19. 14 CFR 36.805 - Noise limits.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Noise limits. 36.805 Section 36.805...: AIRCRAFT TYPE AND AIRWORTHINESS CERTIFICATION Helicopters § 36.805 Noise limits. (a) Compliance with the... levels of the helicopter are no greater than the applicable limits prescribed under section H36.305...

  20. Clustering of noise-induced oscillations

    DEFF Research Database (Denmark)

    Sosnovtseva, Olga; Fomin, A I; Postnov, D E

    2001-01-01

    The subject of our study is clustering in a population of excitable systems driven by Gaussian white noise and with randomly distributed coupling strength. The cluster state is frequency-locked state in which all functional units run at the same noise-induced frequency. Cooperative dynamics...

  1. Investigation of hydraulic transmission noise sources

    Science.gov (United States)

    Klop, Richard J.

    Advanced hydrostatic transmissions and hydraulic hybrids show potential in new market segments such as commercial vehicles and passenger cars. Such new applications regard low noise generation as a high priority, thus, demanding new quiet hydrostatic transmission designs. In this thesis, the aim is to investigate noise sources of hydrostatic transmissions to discover strategies for designing compact and quiet solutions. A model has been developed to capture the interaction of a pump and motor working in a hydrostatic transmission and to predict overall noise sources. This model allows a designer to compare noise sources for various configurations and to design compact and inherently quiet solutions. The model describes dynamics of the system by coupling lumped parameter pump and motor models with a one-dimensional unsteady compressible transmission line model. The model has been verified with dynamic pressure measurements in the line over a wide operating range for several system structures. Simulation studies were performed illustrating sensitivities of several design variables and the potential of the model to design transmissions with minimal noise sources. A semi-anechoic chamber has been designed and constructed suitable for sound intensity measurements that can be used to derive sound power. Measurements proved the potential to reduce audible noise by predicting and reducing both noise sources. Sound power measurements were conducted on a series hybrid transmission test bench to validate the model and compare predicted noise sources with sound power.

  2. Internal noise estimates correlate with autistic traits.

    Science.gov (United States)

    Vilidaite, Greta; Yu, Miaomiao; Baker, Daniel H

    2017-08-01

    Previous neuroimaging research has reported increased internal (neural) noise in sensory systems of autistic individuals. However, it is unclear if this difference has behavioural or perceptual consequences, as previous attempts at measuring internal noise in ASD psychophysically have been indirect. Here, we use a "gold standard" psychophysical double-pass paradigm to investigate the relationship between internal noise and autistic traits in the neurotypical population (n = 43). We measured internal noise in three tasks (contrast perception, facial expression intensity perception, and number summation) to estimate a global internal noise factor using principal components analysis. This global internal noise was positively correlated with autistic traits (rs  = 0.32, P = 0.035). This suggests that increased internal noise is associated with the ASD phenotype even in subclinical populations. The finding is discussed in relation to the neural and genetic basis of internal noise in ASD. Autism Res 2017, 10: 1384-1391. © 2017 International Society for Autism Research, Wiley Periodicals, Inc. © 2017 International Society for Autism Research, Wiley Periodicals, Inc.

  3. Ambiguity noise analysis of a SAR system

    Science.gov (United States)

    Tian, Haishan; Chang, Wenge; Li, Xiangyang

    2015-12-01

    The presence of range and azimuth (or Doppler) ambiguities in synthetic aperture radars (SARs) is well known. The ambiguity noise is related to the antenna pattern and the value of pulse repetition frequency (PRF). Because a new frequency modulated continuous wave (FMCW) SAR has the characters of low cost and small size, and the capacity of real-time signal processing, the antenna will likely vibrate or deform due to a lack of the stabilized platform. And the value of PRF cannot be much high because of the high computation burden for the real-time processing. The aim of this study is to access and improve the performance of a new FMCW SAR system based on the ambiguity noise. First, the quantitative analysis of the system's ambiguity noise level is performed; an antenna with low sidelobes is designed. The conclusion is that the range ambiguity noise is small; the azimuth ambiguity noise is somewhat increased, however, it is sufficiently small to have marginal influence on the image quality. Finally, the ambiguity noise level is measured using the imaging data from a Ku-band FMCW SAR. The results of this study show that the measured noise level coincides with the theoretical noise level.

  4. Predicting annoyance by wind turbine noise

    NARCIS (Netherlands)

    Janssen, S.A.; Vos, H.; Eisses, A.R.; Pedersen, E.

    2010-01-01

    While wind turbines have beneficial effects for the environment, they inevitably generate environmental noise. In order to protect residents against unacceptable levels of noise, exposure-response relationships are needed to predict the expected percentage of people annoyed or highly annoyed at a gi

  5. Thermal noise in linear passive multiports

    Energy Technology Data Exchange (ETDEWEB)

    Agouridis, D.C.

    1987-01-01

    The noise temperature of a linear passive multiport is related to the temperatures of the terminations of its input ports and the temperature of the multiport itself. In reciprocal multiports the noise contributions of these sources are not correlated, but may be correlated in non-reciprocal multiports.

  6. Predicting annoyance by wind turbine noise

    NARCIS (Netherlands)

    Janssen, S.A.; Vos, H.; Eisses, A.R.; Pedersen, E.

    2010-01-01

    While wind turbines have beneficial effects for the environment, they inevitably generate environmental noise. In order to protect residents against unacceptable levels of noise, exposure-response relationships are needed to predict the expected percentage of people annoyed or highly annoyed at a

  7. Shot noise in YBCO bicrystal Josephson junctions

    DEFF Research Database (Denmark)

    Constantinian, K.Y.; Ovsyannikov, G.A.; Borisenko, I.V.;

    2003-01-01

    We measured spectral noise density in YBCO symmetric bicrystal Josephson junctions on sapphire substrates at bias voltages up to 100 mV and T 4.2 K. Normal state resistance of the Josephson junctions, R-N = 20-90 Omega and ICRN up to 2.2 mV have been observed in the experimental samples. Noise...

  8. Amperometric Noise at Thin Film Band Electrodes

    DEFF Research Database (Denmark)

    Larsen, Simon T.; Heien, Michael L.; Taboryski, Rafael

    2012-01-01

    polymers and measured the current noise in physiological buffer solution for a wide range of different electrode areas. The noise measurements could be modeled by an analytical expression, representing the electrochemical cell as a resistor and capacitor in series. The studies revealed three domains...

  9. Climb to Cruise Noise Test Results

    Science.gov (United States)

    Joshi, M. C.; Yamamoto, K. J.; Donelson, M. J.; Golub, R. A.; Rawls, J. W.

    1999-01-01

    A semi-empirical formula for the prediction of the broadband shock associated noise from rectangular supersonic jets in the fly-over plane has been developed. The predicted noise spectra compared very favorable with the measurement of Ponton, Manning and Seiner. Extension to side-line directions will be carried out.

  10. Noise limitations in optical linear algebra processors.

    Science.gov (United States)

    Batsell, S G; Jong, T L; Walkup, J F; Krile, T F

    1990-05-10

    A general statistical noise model is presented for optical linear algebra processors. A statistical analysis which includes device noise, the multiplication process, and the addition operation is undertaken. We focus on those processes which are architecturally independent. Finally, experimental results which verify the analytical predictions are also presented.

  11. Thermal Noise Canceling in LNAs: A Review

    NARCIS (Netherlands)

    Nauta, Bram; Klumperink, Eric A.M.; Bruccoleri, Federico

    2004-01-01

    Most wide-band amplifiers suffer from a fundamental trade-off between noise figure NF and source impedance matching, which limits NF to values typically above 3dB. Recently, a feed-forward noise canceling technique has been proposed to break this trade-off. This paper reviews the principle of the te

  12. Limits of noise squeezing in Kerr effect

    CERN Document Server

    Bajer, J; Tanas, R

    2002-01-01

    It is well known that the optical Kerr effect can be a source of highly squeezed light, however the analytical limit of the noise suppression has not been found yet. The process is reconsidered and an analytical estimation of the optimal quadrature noise level is presented. The validity of the new scaling law is checked numerically and analytically.

  13. Charting environmental pollution. [by noise measurements

    Science.gov (United States)

    Halpert, E.; Bizo, F.; Karacsonyi, Z.

    1974-01-01

    It is found that areas affected by different noxious agents are within the limits traced for high noise level areas; consequently, it is suggested that high noise pressure levels should be used as the primary indication of environmental pollution. A complex methodology is reported for charting environmental pollution due to physical, chemical and biological noxious agents on the scale of an industrial district.

  14. Annoyance from environmental noise across the lifespan

    NARCIS (Netherlands)

    Gerven, P.W.M. van; Vos, H.; Boxtel, M.P.J. van; Janssen, S.A.; Miedema, H.M.E.

    2009-01-01

    Curvilinear effects of age on self-reported annoyance from environmental noise were investigated in a pooled international and a Dutch sample of in total 62,983 individuals aged between 15 and 102 years. All respondents were frequently exposed to varying levels of transportation noise (i.e., aircraf

  15. Microwave Oscillator Would Have Reduced Phase Noise

    Science.gov (United States)

    Dick, G. John; Saunders, Jon

    1991-01-01

    Microwave oscillators of proposed new type incorporate suppressed-carrier/negative-feedback feature to reduce phase noise near their carrier frequencies. Concept results in phase noise less than achievable by cryogenically stabilized microwave components or by room-temperature oscillators stabilized by quartz crystals. Implemented in three different versions.

  16. Low-noise detection of ultracold atoms.

    Science.gov (United States)

    McGuirk, J M; Foster, G T; Fixler, J B; Kasevich, M A

    2001-03-15

    We have demonstrated a new technique for detecting ultracold atoms. A balanced detection technique was used to reduce laser-induced detection noise in conjunction with modulation-transfer spectroscopy to distinguish cold atoms from a thermal cloud. Using this technique, we have achieved signal-to-noise ratios in excess of 2000:1.

  17. PERFORMANCE OF IMPULSE NOISE DETECTION METHODS IN REMOTE SENSING IMAGES

    Directory of Open Access Journals (Sweden)

    Mrs.V.RADHIKA,

    2010-09-01

    Full Text Available Remote sensing (RS images are affected by different types of noises like Gaussian noise, speckle noise and impulse noise. These noises are introduced into the RS images during acquisition or transmission process. The main challenge in impulse noise removal is to suppress the noise as well as to preserve the details (edges. Removal ofthe impulse noise is done by two stages: detection of noisy pixel and replacement of that pixel. Detecting and Removing or reducing impulse noise is a very active research area in image processing. In this paper three different existing detection methods are discussed with the intension of developing a new one.

  18. Adaptive Noise Reduction Scheme for Salt and Pepper

    CERN Document Server

    Gebreyohannes, Tina

    2012-01-01

    In this paper, a new adaptive noise reduction scheme for images corrupted by impulse noise is presented. The proposed scheme efficiently identifies and reduces salt and pepper noise. MAG (Mean Absolute Gradient) is used to identify pixels which are most likely corrupted by salt and pepper noise that are candidates for further median based noise reduction processing. Directional filtering is then applied after noise reduction to achieve a good tradeoff between detail preservation and noise removal. The proposed scheme can remove salt and pepper noise with noise density as high as 90% and produce better result in terms of qualitative and quantitative measures of images.

  19. EURailNoise: a study of European priorities and strategies for railway noise abatement

    Science.gov (United States)

    Kalivoda, M.; Danneskiold-Samsøe, U.; Krüger, F.; Barsikow, B.

    2003-10-01

    The European Union is developing its noise policy by using a number of expert groups on specific noise issues. One of the most relevant noise problems is railway traffic which is dealt with by Working Group 6 (WG 6). The Commission of the European Union appointed a consortium of six consultants and experts in railway noise to prepare a study on European priorities and strategies for railway noise abatement. The main purpose of this study was to support the work within WG 6 and to create an inventory of measures for future railway noise abatement policy of the European Union. The EURailNoise study was to be completed in autumn 2001. The countries included the European Union member states, together with Norway, and Switzerland, and three prospective members (Hungary, the Czech Republic, and Poland). The EURailNoise study consisted of three main parts. The baseline was a review of current European legislation on railway noise generation as well as noise perception. In parallel a documentation of cases, where technical measures against railway noise had been successfully applied, was prepared using a classification of "good practice", "promising new technology", and "promising research results". The second part covered the potential for further noise reduction demonstrated for High Speed Passenger Traffic, S-Trains, Locomotives, Trams, Freight Traffic, Track Design and finally Wheels and Track Monitoring and Maintenance. Thirdly, a strategy for future activities of the Commission concerning the reduction of rail noise was to be proposed including a proposal for noise emission limits. This paper summarizes the results of the EURailNoise study.

  20. Spectra for the product of Gaussian noises

    CERN Document Server

    Kish, L B; Gingl, Z; Granqvist, C G

    2012-01-01

    Products of Gaussian noises often emerge as the result of non-linear detection techniques or as a parasitic effect, and their proper handling is important in many practical applications, including in fluctuation-enhanced sensing, indoor air or environmental quality monitoring, etc. We use Rice's random phase oscillator formalism to calculate the power density spectra variance for the product of two Gaussian band-limited white noises with zero-mean and the same bandwidth W. The ensuing noise spectrum is found to decrease linearly from zero frequency to 2W, and it is zero for frequencies greater than 2W. Analogous calculations performed for the square of a single Gaussian noise confirm earlier results. The spectrum at non-zero frequencies, and the variance of the square of a noise, is amplified by a factor two as a consequence of correlation effects between frequency products. Our analytic results is corroborated by computer simulations.