WorldWideScience

Sample records for pseudo cavity dumping

  1. Pulse compression by Raman induced cavity dumping

    International Nuclear Information System (INIS)

    De Rougemont, F.; Xian, D.K.; Frey, R.; Pradere, F.

    1985-01-01

    High efficiency pulse compression using Raman induced cavity dumping has been studied theoretically and experimentally. Through stimulated Raman scattering the electromagnetic energy at a primary frequency is down-converted and extracted from a storage cavity containing the Raman medium. Energy storage may be achieved either at the laser frequency by using a laser medium inside the storage cavity, or performed at a new frequency obtained through an intracavity nonlinear process. The storage cavity may be dumped passively through stimulated Raman scattering either in an oscillator or in an amplifier. All these cases have been studied by using a ruby laser as the pump source and compressed hydrogen as the Raman scatter. Results differ slightly accordingly to the technique used, but pulse shortenings higher than 10 and quantum efficiencies higher than 80% were obtained. This method could also be used with large power lasers of any wavelength from the ultraviolet to the farinfrared spectral region

  2. High stable electro-optical cavity-dumped Nd:YAG laser

    International Nuclear Information System (INIS)

    Ma, Y F; Yu, X; Zhang, J W; Li, H

    2012-01-01

    In this paper, an electro-optical cavity-dumped 10 Hz Nd:Y 3 Al 5 O 12 (Nd:YAG) laser was demonstrated. We designed an optimized high stable concavo-convex cavity according to the thermal-insensitive theory that the cavity could be deep stable and be insensitive to the change of thermal lens of laser crystal when g 1 *g 2 = 1/2. The output pulse width was constant at 6.0±0.1 ns. The maximum output energy was 40 mJ. The laser had outstanding stability of output characteristics. The fluctuations of average output energy and divergence angle within 8 cycles were 1.24% and 0.06 mrad, respectively

  3. High-efficiency cavity-dumped micro-chip Yb:YAG laser

    Science.gov (United States)

    Nishio, M.; Maruko, A.; Inoue, M.; Takama, M.; Matsubara, S.; Okunishi, H.; Kato, K.; Kyomoto, K.; Yoshida, T.; Shimabayashi, K.; Morioka, M.; Inayoshi, S.; Yamagata, S.; Kawato, S.

    2014-09-01

    High-efficiency cavity-dumped ytterbium-doped yttrium aluminum garnet (Yb:YAG) laser was developed. Although the high quantum efficiency of ytterbium-doped laser materials is appropriate for high-efficiency laser oscillation, the efficiency is decreased by their quasi-three/four laser natures. High gain operation by high intensity pumping is suitable for high efficiency oscillation on the quasi-three/four lasers without extremely low temperature cooling. In our group, highest efficiency oscillations for continuous wave, nanosecond to picosecond pulse lasers were achieved at room temperature by the high gain operation in which pump intensities were beyond 100 kW/cm2.

  4. Very high repetition-rate electro-optical cavity-dumped Nd: YVO4 laser with optics and dynamics stabilities

    Science.gov (United States)

    Liu, Xuesong; Shi, Zhaohui; Huang, Yutao; Fan, Zhongwei; Yu, Jin; Zhang, Jing; Hou, Liqun

    2015-02-01

    In this paper, a very high repetition-rate, short-pulse, electro-optical cavity-dumped Nd: YVO4 laser is experimentally and theoretically investigated. The laser performance is optimized from two aspects. Firstly, the laser resonator is designed for a good thermal stability under large pump power fluctuation through optics methods. Secondly, dynamics simulation as well as experiments verifies that cavity dumping at very high repetition rate has better stability than medium/high repetition rate. At 30 W, 880 nm pump power, up to 500 kHz, constant 5 ns, stable 1064 nm fundamental-mode laser pulses can be obtained with 10 W average output power.

  5. LD end pumped mode locked and cavity dumped Nd:YAP laser at 1.34 μm

    Science.gov (United States)

    Wang, X.; Wang, S.; Rhee, H.; Eichler, H. J.; Meister, S.

    2011-06-01

    We report a LD end pumped actively mode locked, passively Q switched and cavity dumped Nd:YAP laser at 1.34 μm. The dumped output pulse energy of 160 μJ is obtained at a repetition rate of 10 Hz. Passing through a LD end pumped, double-passed Nd:YAP amplifier the pulse energy is amplified to 1.44 mJ. The corresponding amplification factor is 9. Stimulated Raman scattering experiment is taken with a 9 mm long PbWO4 Raman crystal. Maximum of 20% Raman conversion is reached.

  6. 650-nJ pulses from a cavity-dumped Yb:fiber-pumped ultrafast optical parametric oscillator

    Science.gov (United States)

    Lamour, Tobias P.; Reid, Derryck T.

    2011-08-01

    Sub-250-fs pulses with energies of up to 650 nJ and peak powers up to 2.07 MW were generated from a cavity-dumped optical parametric oscillator, synchronously-pumped at 15.3 MHz with sub-400-fs pulses from an Yb:fiber laser. The average beam quality factor of the dumped output was M2 ~1.2 and the total relative-intensity noise was 8 mdBc, making the system a promising candidate for ultrafast laser inscription of infrared materials.

  7. Dumping convention

    International Nuclear Information System (INIS)

    Roche, P.

    1992-01-01

    Sea dumping of radioactive waste has, since 1983, been precluded under a moratorium established by the London Dumping Convention. Pressure from the nuclear industry to allow ocean dumping of nuclear waste is reported in this article. (author)

  8. Characterisation of the light pulses of a cavity dumped dye laser pumped by a cw mode-locked and q-switched Nd:YAG laser

    International Nuclear Information System (INIS)

    Geist, P.; Heisel, F.; Martz, A.; Miehe, J.A.; Miller, R.J.D.

    1984-01-01

    The frequency doubled pulses (of 532 nm) obtained, with the help of a KTP crystal, from those delivered by either a continuous wave mode-locked (100 MHz) or mode-locked Q-switched (0-1 KHz) Nd: YAG laser, are analyzed by means of a streak camera, operating in synchroscan or triggered mode. In the step-by-step measurements the pulse stability, concerning form and amplitude, is shown. In addition, measurements effectuated with synchronously pumped and cavity dumped dye laser (Rhodamine 6G), controlled by a Pockels cell, allows the obtention of stable and reproducible single pulses of 30 ps duration, 10 μJ energy and 500Hz frequency [fr

  9. Pulsed, all solid-state light source in the visible spectral region based on non-linear cavity dumping

    DEFF Research Database (Denmark)

    Tidemand-Lichtenberg, Peter; Andersen, Martin; Johansson, Sandra

    We propose a novel generic approach for generation of pulsed light in the visible spectrum, based on SFG between the high circulating intra-cavity power of a high finesse CW laser and a single-passed pulsed laser.......We propose a novel generic approach for generation of pulsed light in the visible spectrum, based on SFG between the high circulating intra-cavity power of a high finesse CW laser and a single-passed pulsed laser....

  10. High efficiency and good beam quality of electro-optic, cavity-dumped and double-end pumped Nd:YLF laser

    Science.gov (United States)

    Tang, X. X.; Fan, Z. W.; Qiu, J. S.; Lian, F. Q.; Zhang, X. L.

    2012-06-01

    In this paper, we describe a Nd:YLF laser based on high-speed RTP electro-optical cavity dumping technique. Two home-made 150 W fiber pump modules are used from both sides to pump Nd:YLF crystal. Coupling systems are the key elements in end-pumped solid-state lasers, the aberrations of which greatly affect the efficiency of the lasers. In order to get high efficient and good quality laser output, the optical software ZEMAX is used to design a four-piece coupling system. When the pumped energy is 32 mJ at the repetition rate of 1 Hz, the output energy is 6.5 mJ with 2.5 ns pulse width. When the pumped energy is 13.1 W at the repetition rate of 200 Hz, the output energy is 2.2 W with small M 2 factor where M {/x 2} is 1.04, and M {/y 2} is 1.05, and the light-light conversion efficiency is up to 16.8%.

  11. Social dumping

    DEFF Research Database (Denmark)

    Pedersen, Klaus

    2010-01-01

    bidrag til, at OK-2010 "landes" fredeligt, fordi aftalen giver fagforeningerne en væsentlig indrømmelse i indsatsen mod social dumping. Aftalen har rigtignok til formål at imødekomme et af fagbevægelsens centrale overenskomstkrav om nye redskaber i indsatsen mod "social dumping". Men hvad er det aftalen...

  12. Four-wave-mixing and nonlinear cavity dumping of 280 picosecond 2nd Stokes pulse at 1.3 μm from Nd:SrMoO4 self-Raman laser

    International Nuclear Information System (INIS)

    Smetanin, S N; Ivleva, L I; Jelínek, M Jr; Kubeček, V; Jelínková, H; Shurygin, A S

    2016-01-01

    The 280 picosecond 2nd Stokes Raman pulses at 1.3 μm were generated directly from the miniature diode-pumped Nd:SrMoO 4 self-Raman laser. Using the 90° phase matching insensitive to the angular mismatch, the self-Raman laser allowed for the achievement of the four-wave-mixing generation of the 2nd Stokes Raman pulse directly in the active Nd:SrMoO 4 crystal at stimulated Raman scattering (SRS) self-conversion of the laser radiation. The passive Cr:YAG Q-switching and nonlinear cavity dumping was used without any phase locking device. (letter)

  13. Ocean Dumping Control Regulations

    International Nuclear Information System (INIS)

    1978-01-01

    These Regulations were made further to the Ocean Dumping Control Act which provides for restrictions in dumping operations. The Regulations contain model applications for permits to dump or load a series of materials. (NEA)

  14. Ocean Dumping Control Act

    International Nuclear Information System (INIS)

    1975-01-01

    This Act provides for the control of dumping of wastes and other substances in the ocean in accordance with the London Convention of 1972 on Prevention of Marine Pollution by the Dumping of Wastes and other Matter to which Canada is a Party. Radioactive wastes are included in the prohibited and restricted substances. (NEA)

  15. Perisplenic Pseudo

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyo Heon; Cho, Sin Young; Suh, Hong Kil; Kim, Ji Hyeon; Choi, Chul Soon; Lee, Eil Seong; Kang, Ik Won [Hallym University College of Medicine, Chuncheon (Korea, Republic of)

    1995-12-15

    Perisplenic pseudo 'fluid collection' is one of the rare normal variations. Its frequency and sonographic findings for the differentiation from true perisplenic fluid collection have not been well described. Thus, we performed this study. The examination was performed with special attention to the splenic and perisplenic areas. We excluded patients with proved or suspected liver cirrhosis, pancreatic diseases,and abdominal trauma from the study population, but did not exclude the patients with chronic hepatitis and the carriers of hepatitis B virus. Of the examined 4794 patients, 8 cases showed perisplenic pseudo 'fluid collection'. Two of them were confirmed with computed tomography and liver scan, and six were inferred from the fact proved to be a part of the left lobe extension of the liver by tracing with the transducer. All cases ofperisplenic pseudo 'fluid collection' showed hypoechoic crescent area with hepatic ductal echoes. Perisplenic pseudo 'fluid collection' is very rare. The helpful findings for the differentiation from true fluid collection are the hepatic ductal echoes seen in the normal liver, proof of continuation into remained voluminous liver by tracing with the transducer. High awareness of it would prevent further unnecessary studies such as computed tomography and liver scan

  16. Perisplenic Pseudo

    International Nuclear Information System (INIS)

    Kim, Hyo Heon; Cho, Sin Young; Suh, Hong Kil; Kim, Ji Hyeon; Choi, Chul Soon; Lee, Eil Seong; Kang, Ik Won

    1995-01-01

    Perisplenic pseudo 'fluid collection' is one of the rare normal variations. Its frequency and sonographic findings for the differentiation from true perisplenic fluid collection have not been well described. Thus, we performed this study. The examination was performed with special attention to the splenic and perisplenic areas. We excluded patients with proved or suspected liver cirrhosis, pancreatic diseases,and abdominal trauma from the study population, but did not exclude the patients with chronic hepatitis and the carriers of hepatitis B virus. Of the examined 4794 patients, 8 cases showed perisplenic pseudo 'fluid collection'. Two of them were confirmed with computed tomography and liver scan, and six were inferred from the fact proved to be a part of the left lobe extension of the liver by tracing with the transducer. All cases ofperisplenic pseudo 'fluid collection' showed hypoechoic crescent area with hepatic ductal echoes. Perisplenic pseudo 'fluid collection' is very rare. The helpful findings for the differentiation from true fluid collection are the hepatic ductal echoes seen in the normal liver, proof of continuation into remained voluminous liver by tracing with the transducer. High awareness of it would prevent further unnecessary studies such as computed tomography and liver scan

  17. Ocean Dumping: International Treaties

    Science.gov (United States)

    The London Convention and London Protocol are global treaties to protect the marine environment from pollution caused by the ocean dumping of wastes. The Marine, Protection, Research and Sanctuaries Act implements the requirements of the LC.

  18. The beam dump tunnels

    CERN Multimedia

    Patrice Loïez

    2002-01-01

    In these images workers are digging the tunnels that will be used to dump the counter-circulating beams. Travelling just a fraction under the speed of light, the beams at the LHC will each carry the energy of an aircraft carrier travelling at 12 knots. In order to dispose of these beams safely, a beam dump is used to extract the beam and diffuse it before it collides with a radiation shielded graphite target.

  19. Allegheny County Illegal Dump Sites

    Data.gov (United States)

    Allegheny County / City of Pittsburgh / Western PA Regional Data Center — The Illegal Dump Site dataset includes information on illegal dump sites, their type of trash, and the estimate tons of trash at each site. The information was...

  20. Premature beam dumps in 2011

    CERN Document Server

    Albert, Markus

    2012-01-01

    The statistical analysis of all non-programmed beam dumps during the 2011 proton run is presented. The selection criteria of fills that got considered were that the beam intensity of each of the two beams exceeded at least 1e12 particles per beam in order to exclude all probe beam dumps and most of the MPS test dumps. A distribution of beam dump causes by system is shown, as well as the time it took to re-establish injection after a non-programmed dump for fills which made it into STABLE BEAMS. This was done in an attempt to evaluate the cost of those non-programmed dumps in terms of time.

  1. Dumping at Sea Act 1974

    International Nuclear Information System (INIS)

    1974-01-01

    This Act enables the United Kingdom Government to ratify both the Oslo Convention of 1972 for the Prevention of Marine Pollution by Dumping from Ships and Aircraft and the London Convention of 1972 on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter. (NEA) [fr

  2. Dumping in a Global World

    NARCIS (Netherlands)

    J.L. Moraga-Gonzalez (José Luis); J.M.A. Viaene (Jean-Marie)

    2004-01-01

    textabstractAnti-dumping actions are now the trade policy of choice of developing and transition economies. To understand why these economies have increasingly applied anti-dumping laws, we build a simple theoretical model of vertical intra-industry trade and investigate the strategic incentives of

  3. Discrete pseudo-integrals

    Czech Academy of Sciences Publication Activity Database

    Mesiar, Radko; Li, J.; Pap, E.

    2013-01-01

    Roč. 54, č. 3 (2013), s. 357-364 ISSN 0888-613X R&D Projects: GA ČR GAP402/11/0378 Institutional support: RVO:67985556 Keywords : concave integral * pseudo-addition * pseudo-multiplication Subject RIV: BA - General Mathematics Impact factor: 1.977, year: 2013 http://library.utia.cas.cz/separaty/2013/E/mesiar-discrete pseudo-integrals.pdf

  4. Pseudo-hermafroditismo masculino em cadela

    OpenAIRE

    Fantoni,M.S.; Silva,B.C.; Ferreira,L.F.L.; Valle,G.R.; Rachid,M.A.

    2012-01-01

    A case of male pseudo-hermaphrodite in a six-month-old Pinscher dog with mild signs of agression towards other dogs is reported. The animal presented fibrous mass in clitorial region, with structure similar to a diminutive penis. Testicles were found in the abdominal cavity, uterus had normal size and localization and hypertrophic clitoris was seen during exploratory laparotomy. The histopathological examination revealed testicular tissue, composed of hypotrophic seminipherous tubules and exu...

  5. Beam-dump kicker magnets

    International Nuclear Information System (INIS)

    Bulos, F.; Odian, A.; Tomlin, B.

    1983-01-01

    The beam-dump kicker magnets are located in the final focus region and, in conjunction with septum magnets, extract the beams after they have passed the interaction point (IP) and direct them to their respective dumps. Two schemes for these kickers have been under consideration; ferrite transmission line magnets utilizing technology common with damping rings and positron target kickers, and current loop magnets which are possible only for the dump kickers, where the rise time of the magnetic pulse can be comparatively longer; approximately 400 nanoseconds as compared with 50 nanoseconds for the others. A prototype ferrite kicker has been built and is undergoing tests. Since the current loop requires lower voltage and power plus some additional savings in cost, we decided to build and test a prototype. This note describes in detail an optimized design for the current loop magnets and their associated pulse circuitry

  6. Sea dumping of hazardous wastes

    International Nuclear Information System (INIS)

    Thomas, J.

    1980-01-01

    From 1967 until 1976 ca. 45,000 t of weak radioactive wastes had been dumped into the sea during several actions under the supervision of the NEA. The requirements to be deduced from the experiences with regard to marine areas, packaging and transports of the wastes are described. Up to now the possibilities of the sea dumping of strong radioactive wastes has been just discussed. The natural removal of the decay heat by sea water would be advantageous but the problem of water-proof packagings for the period of 1000 years have not been solved yet. (orig.) [de

  7. Down in the dumps - cheerfully

    International Nuclear Information System (INIS)

    Ruhmer, W.T.

    1984-01-01

    Scavenging gold and uranium from the sands dumps and slimes dams is a highly profitable operation. In a few pages the author summarises some of the permutations and combinations of the various processes employed by South African concerns to achieve economic results

  8. Egg dumping by predatory insects

    Czech Academy of Sciences Publication Activity Database

    Corbani, A. C.; Ferrer, A.; Dixon, Anthony F. G.; Hemptinne, J. L.

    2011-01-01

    Roč. 36, č. 3 (2011), s. 290-293 ISSN 0307-6962 Institutional research plan: CEZ:AV0Z60870520 Keywords : Egg dumping * ladybird beetles * oocyte resorption * trophic egg Subject RIV: EH - Ecology, Behaviour Impact factor: 1.330, year: 2011

  9. 30 CFR 77.1608 - Dumping facilities.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Dumping facilities. 77.1608 Section 77.1608 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... Haulage § 77.1608 Dumping facilities. (a) Dumping locations and haulage roads shall be kept reasonably...

  10. Pseudo-set framing.

    Science.gov (United States)

    Barasz, Kate; John, Leslie K; Keenan, Elizabeth A; Norton, Michael I

    2017-10-01

    Pseudo-set framing-arbitrarily grouping items or tasks together as part of an apparent "set"-motivates people to reach perceived completion points. Pseudo-set framing changes gambling choices (Study 1), effort (Studies 2 and 3), giving behavior (Field Data and Study 4), and purchase decisions (Study 5). These effects persist in the absence of any reward, when a cost must be incurred, and after participants are explicitly informed of the arbitrariness of the set. Drawing on Gestalt psychology, we develop a conceptual account that predicts what will-and will not-act as a pseudo-set, and defines the psychological process through which these pseudo-sets affect behavior: over and above typical reference points, pseudo-set framing alters perceptions of (in)completeness, making intermediate progress seem less complete. In turn, these feelings of incompleteness motivate people to persist until the pseudo-set has been fulfilled. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  11. EU Lobbying and Anti-Dumping Policy

    DEFF Research Database (Denmark)

    Nielsen, Jørgen Ulff-Møller; Svendsen, Gert Tinggaard

    2012-01-01

    of petitioning firms and Council voting in the case of anti-dumping policy. If the political position of countries in anti-dumping cases is influenced by domestic lobbying efforts, we expect that the empirical pattern of country distribution of petitioning firms in EU anti-dumping cases corresponds closely...... to the empirical pattern of EU country distribution in Council voting. Our results show a low petitioning intensity for anti-dumping investigations and a high voting intensity against anti-dumping measures in Northern Europe. Thus, it seems likely that domestic lobbying efforts have influenced the political...

  12. Powershift transmission for dump trucks; Neues Lastschaltgetriebe fuer Dump Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Rebholz, Wolfgang; Geis, Joerg; Riedhammer, Michael [ZF Friedrichshafen AG, Friedrichshafen (Germany)

    2012-04-15

    Articulated dumpers (also called dump trucks) are used in many locations where large quantities of earth, spoil, gravel or other materials have to be moved on construction sites or in quarries. ZF has developed a new transmission with eight forward and four reverse gears up to production standard specifically for use in these vehicles. The integrated primary retarder is continuously controllable and provides maximum braking torque of up to 1800 Nm. (orig.)

  13. Conceptual Design of the RHIC Dump Core

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, A. J. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    1995-09-26

    Conceptually, the internal dump consists of a "core" whose purpose is to absorb the energy of the beam, and surrounding shielding whose purpose is to attenuate radiation. Design of the core for an internal dump has two problems which must be overcome. The first problem is preserving the integrity of the dump core. The bunches must be dispersed laterally an amount sufficient to keep the energy density from cracking the dump core material. Since the dump kickers in RHIC are only ~25m upstream of the entrance face of the dump, this is i a difficult problem. The second problem, not addressed in this note, is that dumping the beam should not quench downstream magnets. Preliminary calculations related to both of these problems have been presented in earlier notes.

  14. Pseudo-hermafroditismo masculino em cadela

    Directory of Open Access Journals (Sweden)

    M.S. Fantoni

    2012-06-01

    Full Text Available A case of male pseudo-hermaphrodite in a six-month-old Pinscher dog with mild signs of agression towards other dogs is reported. The animal presented fibrous mass in clitorial region, with structure similar to a diminutive penis. Testicles were found in the abdominal cavity, uterus had normal size and localization and hypertrophic clitoris was seen during exploratory laparotomy. The histopathological examination revealed testicular tissue, composed of hypotrophic seminipherous tubules and exuberant stroma and uterus with normal histological appearance. Moreover, the animal presented high levels of testosterone.

  15. Old dumps of uranium mining

    International Nuclear Information System (INIS)

    Gatzweiler, R.; Mager, D.

    1993-01-01

    The production of natural uranium through mining and milling results in large volumes of low-level radioactive waste, mainly in mine dumps and mill tailings. Hazards which relate to abandoned uranium production sites and environmental remediation approaches are described in reference to the Wismut case. During the period 1947 to 1990 the former Soviet-German Wismut Corporation produced about 200 000 t of uranium from several deposits in Thuringia and Saxonia within a relatively small and densely populated area. These activities resulted in major land disturbance and other environmental damage. Restoration problems are highlighted. (orig.)

  16. THE PSEUDO-SMARANDACHE FUNCTION

    OpenAIRE

    David Gorski

    2007-01-01

    The Pseudo-Smarandache Function is part of number theory. The function comes from the Smarandache Function. The Pseudo-Smarandache Function is represented by Z(n) where n represents any natural number.

  17. Clay sealing for dumps - new findings from suitability tests

    Energy Technology Data Exchange (ETDEWEB)

    Kunde, L.; Kuntsche, K.; Duellmann, H.

    1988-06-01

    Extensive suitability tests were carried out in the laboratory and field on various clays of the Lower-Rhineland brown coal mining area. The purpose of these tests was to determine the basic suitability of these clays for use as sealing layers for residue dumps. The tests also furnished criteria according to which a specific imperviousness can be achieved. The results of the tests can be summed up as follows: Since the material properties of the in-situ clays vary widely, not only mean values but also corresponding variation coefficients must be adhered to. For the purpose of checking the quality - contrary to the hitherto applied assessment practice - the decisive factor is not the testing of the dry density as compared to the Proctor density, but the homogeneity of the sealing layer that is achieved as a result of the size reduction and compaction of the pseudo-granular structure. Using suitable equipment, homogeneities, for which permeability coefficients of k less than or equal to 10/sup -9/ m/s in the dump sealing are obtained can be achieved with the clays that were examined.

  18. Pseudo-deterministic Algorithms

    OpenAIRE

    Goldwasser , Shafi

    2012-01-01

    International audience; In this talk we describe a new type of probabilistic algorithm which we call Bellagio Algorithms: a randomized algorithm which is guaranteed to run in expected polynomial time, and to produce a correct and unique solution with high probability. These algorithms are pseudo-deterministic: they can not be distinguished from deterministic algorithms in polynomial time by a probabilistic polynomial time observer with black box access to the algorithm. We show a necessary an...

  19. The battle of the dumps continues

    International Nuclear Information System (INIS)

    Anon.

    1976-01-01

    Although East Rand Gold and Uranium Company is about to start exploitation of the old slimes dams to produce gold, uranium and sulphuric acid, the battle to suppress dust and establish vegetation on the old dumps continues. The physical problems, planning, co-ordination and legal aspects of mine dump reclamation are outlined

  20. Dilution kicker for the SPS beam dump

    CERN Multimedia

    1974-01-01

    In order to reduce thermal stress on the SPS dump material, the fast-ejected beam was swept horizontally across the dump. This was done with the "dilution kicker" MKDH, still in use at the time of writing. The person on the left is Manfred Mayer. See also 7404072X.

  1. LCT protective dump-switch tests

    International Nuclear Information System (INIS)

    Parsons, W.M.

    1981-01-01

    Each of the six coils in the Large Coil Task (LCT) has a separate power supply, dump resistor, and switching circuit. Each switching circuit contains five switches, two of which are redundant. The three remaining switches perform separate duties in an emergency dump situation. These three switches were tested to determine their ability to meet the LCT conditions

  2. Dental cavities

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/001055.htm Dental cavities To use the sharing features on this page, please enable JavaScript. Dental cavities are holes (or structural damage) in the ...

  3. HDF-EOS Dump Tools

    Science.gov (United States)

    Prasad, U.; Rahabi, A.

    2001-05-01

    The following utilities developed for HDF-EOS format data dump are of special use for Earth science data for NASA's Earth Observation System (EOS). This poster demonstrates their use and application. The first four tools take HDF-EOS data files as input. HDF-EOS Metadata Dumper - metadmp Metadata dumper extracts metadata from EOS data granules. It operates by simply copying blocks of metadata from the file to the standard output. It does not process the metadata in any way. Since all metadata in EOS granules is encoded in the Object Description Language (ODL), the output of metadmp will be in the form of complete ODL statements. EOS data granules may contain up to three different sets of metadata (Core, Archive, and Structural Metadata). HDF-EOS Contents Dumper - heosls Heosls dumper displays the contents of HDF-EOS files. This utility provides detailed information on the POINT, SWATH, and GRID data sets. in the files. For example: it will list, the Geo-location fields, Data fields and objects. HDF-EOS ASCII Dumper - asciidmp The ASCII dump utility extracts fields from EOS data granules into plain ASCII text. The output from asciidmp should be easily human readable. With minor editing, asciidmp's output can be made ingestible by any application with ASCII import capabilities. HDF-EOS Binary Dumper - bindmp The binary dumper utility dumps HDF-EOS objects in binary format. This is useful for feeding the output of it into existing program, which does not understand HDF, for example: custom software and COTS products. HDF-EOS User Friendly Metadata - UFM The UFM utility tool is useful for viewing ECS metadata. UFM takes an EOSDIS ODL metadata file and produces an HTML report of the metadata for display using a web browser. HDF-EOS METCHECK - METCHECK METCHECK can be invoked from either Unix or Dos environment with a set of command line options that a user might use to direct the tool inputs and output . METCHECK validates the inventory metadata in (.met file) using The

  4. PSEUDO-CODEWORD LANDSCAPE

    Energy Technology Data Exchange (ETDEWEB)

    CHERTKOV, MICHAEL [Los Alamos National Laboratory; STEPANOV, MIKHAIL [Los Alamos National Laboratory

    2007-01-10

    The authors discuss performance of Low-Density-Parity-Check (LDPC) codes decoded by Linear Programming (LP) decoding at moderate and large Signal-to-Noise-Ratios (SNR). Frame-Error-Rate (FER) dependence on SNR and the noise space landscape of the coding/decoding scheme are analyzed by a combination of the previously introduced instanton/pseudo-codeword-search method and a new 'dendro' trick. To reduce complexity of the LP decoding for a code with high-degree checks, {ge} 5, they introduce its dendro-LDPC counterpart, that is the code performing identifically to the original one under Maximum-A-Posteriori (MAP) decoding but having reduced (down to three) check connectivity degree. Analyzing number of popular LDPC codes and their dendro versions performing over the Additive-White-Gaussian-Noise (AWGN) channel, they observed two qualitatively different regimes: (i) error-floor sets early, at relatively low SNR, and (ii) FER decays with SNR increase faster at moderate SNR than at the largest SNR. They explain these regimes in terms of the pseudo-codeword spectra of the codes.

  5. Long-term terrain protection over the underground log dumps. Dlouhodoba ochrana terenu nad podzemnimi slozisti

    Energy Technology Data Exchange (ETDEWEB)

    Vacek, J [Ustav geotechniky CSAV, Praha (Czechoslovakia)

    1992-02-01

    Results of experimental research of surface danger of the terrain over underground log dumps are given. Time influence and rock structure influence on surface deformation were analyzed for the purpose of solving rock stability. The example of solving underground cavities influence on surface by using equivalent modelling method is described. This way enables us to take geotechnic route, influence of driving advance and the method backfilling into consideration. The method is convenient for evaluation of landslide effects and for safeguarding measures. 9 figs.

  6. Pseudo-Riemannian Novikov algebras

    Energy Technology Data Exchange (ETDEWEB)

    Chen Zhiqi; Zhu Fuhai [School of Mathematical Sciences and LPMC, Nankai University, Tianjin 300071 (China)], E-mail: chenzhiqi@nankai.edu.cn, E-mail: zhufuhai@nankai.edu.cn

    2008-08-08

    Novikov algebras were introduced in connection with the Poisson brackets of hydrodynamic-type and Hamiltonian operators in formal variational calculus. Pseudo-Riemannian Novikov algebras denote Novikov algebras with non-degenerate invariant symmetric bilinear forms. In this paper, we find that there is a remarkable geometry on pseudo-Riemannian Novikov algebras, and give a special class of pseudo-Riemannian Novikov algebras.

  7. Solid waste dumping site suitability analysis using geographic ...

    African Journals Online (AJOL)

    Solid waste dumping is a serious problem in the urban areas because most solid wastes are not dumped in the suitable areas. Bahir Dar Town has the problem of solid waste dumping site identification. The main objective of this study was to select potential areas for suitable solid waste dumping sites for Bahir Dar Town, ...

  8. Pseudo Class III malocclusion

    Directory of Open Access Journals (Sweden)

    Fadia M. Al-Hummayani

    2016-04-01

    Full Text Available The treatment of deep anterior crossbite is technically challenging due to the difficulty of placing traditional brackets with fixed appliances. This case report represents a none traditional treatment modality to treat deep anterior crossbite in an adult pseudo class III malocclusion complicated by severely retruded, supraerupted upper and lower incisors. Treatment was carried out in 2 phases. Phase I treatment was performed by removable appliance “modified Hawley appliance with inverted labial bow,” some modifications were carried out to it to suit the presented case. Positive overbite and overjet was accomplished in one month, in this phase with minimal forces exerted on the lower incisors. Whereas, phase II treatment was performed with fixed appliances (braces to align teeth and have proper over bite and overjet and to close posterior open bite, this phase was accomplished within 11 month.

  9. Lung inflammatory pseudo tumor

    International Nuclear Information System (INIS)

    Veliz, Elizabeth; Leone, Gaetano; Cano, Fernando; Sanchez, Jaime

    2005-01-01

    The inflammatory pseudo tumor is a non neoplastic process characterized by an irregular growth of inflammatory cells. We described the case of a 38 year-old patient, she went to our institute for a in situ cervix cancer and left lung nodule without breathing symptoms; valued by neumology who did bronchoscopy with biopsy whose result was negative for malignancy. She went to surgery in where we find intraparenquima nodule in felt lingula of approximately 4 cms, we remove it; the result was: Inflammatory pseudotumor. This pathology is a not very frequent, it can develop in diverse regions of the organism, it is frequent in lung. The image tests are not specific for the diagnose, which it is possible only with the biopsy. The treatment is the complete resection. (The author)

  10. High slope waste dumps – a proven possibility

    Directory of Open Access Journals (Sweden)

    Igor Svrkota

    2013-11-01

    Full Text Available This paper is an overview of dumping operations on High Slope Waste Dump at Veliki Krivelj open pit copper mine, RTB Bor, Serbia. The High Slope Waste Dump in Bor is the highest single slope waste dump in the world with the slope height of 405 m. The paper gives the basics and limitations of the designed dumping technology, the redesigned technology, gives an overview of the 13 year long operation and gathered experiences and addresses the main issues of dumping operations in high slope conditions as well as the present condition of the High Slope Waste Dump.

  11. Pseudo color ghost coding imaging with pseudo thermal light

    Science.gov (United States)

    Duan, De-yang; Xia, Yun-jie

    2018-04-01

    We present a new pseudo color imaging scheme named pseudo color ghost coding imaging based on ghost imaging but with multiwavelength source modulated by a spatial light modulator. Compared with conventional pseudo color imaging where there is no nondegenerate wavelength spatial correlations resulting in extra monochromatic images, the degenerate wavelength and nondegenerate wavelength spatial correlations between the idle beam and signal beam can be obtained simultaneously. This scheme can obtain more colorful image with higher quality than that in conventional pseudo color coding techniques. More importantly, a significant advantage of the scheme compared to the conventional pseudo color coding imaging techniques is the image with different colors can be obtained without changing the light source and spatial filter.

  12. Pseudo-interactive monitoring in distributed computing

    International Nuclear Information System (INIS)

    Sfiligoi, I.; Bradley, D.; Livny, M.

    2009-01-01

    Distributed computing, and in particular Grid computing, enables physicists to use thousands of CPU days worth of computing every day, by submitting thousands of compute jobs. Unfortunately, a small fraction of such jobs regularly fail; the reasons vary from disk and network problems to bugs in the user code. A subset of these failures result in jobs being stuck for long periods of time. In order to debug such failures, interactive monitoring is highly desirable; users need to browse through the job log files and check the status of the running processes. Batch systems typically don't provide such services; at best, users get job logs at job termination, and even this may not be possible if the job is stuck in an infinite loop. In this paper we present a novel approach of using regular batch system capabilities of Condor to enable users to access the logs and processes of any running job. This does not provide true interactive access, so commands like vi are not viable, but it does allow operations like ls, cat, top, ps, lsof, netstat and dumping the stack of any process owned by the user; we call this pseudo-interactive monitoring. It is worth noting that the same method can be used to monitor Grid jobs in a glidein-based environment. We further believe that the same mechanism could be applied to many other batch systems.

  13. Pseudo-interactive monitoring in distributed computing

    International Nuclear Information System (INIS)

    Sfiligoi, I; Bradley, D; Livny, M

    2010-01-01

    Distributed computing, and in particular Grid computing, enables physicists to use thousands of CPU days worth of computing every day, by submitting thousands of compute jobs. Unfortunately, a small fraction of such jobs regularly fail; the reasons vary from disk and network problems to bugs in the user code. A subset of these failures result in jobs being stuck for long periods of time. In order to debug such failures, interactive monitoring is highly desirable; users need to browse through the job log files and check the status of the running processes. Batch systems typically don't provide such services; at best, users get job logs at job termination, and even this may not be possible if the job is stuck in an infinite loop. In this paper we present a novel approach of using regular batch system capabilities of Condor to enable users to access the logs and processes of any running job. This does not provide true interactive access, so commands like vi are not viable, but it does allow operations like ls, cat, top, ps, lsof, netstat and dumping the stack of any process owned by the user; we call this pseudo-interactive monitoring. It is worth noting that the same method can be used to monitor Grid jobs in a glidein-based environment. We further believe that the same mechanism could be applied to many other batch systems.

  14. Pseudo-interactive monitoring in distributed computing

    Energy Technology Data Exchange (ETDEWEB)

    Sfiligoi, I.; /Fermilab; Bradley, D.; Livny, M.; /Wisconsin U., Madison

    2009-05-01

    Distributed computing, and in particular Grid computing, enables physicists to use thousands of CPU days worth of computing every day, by submitting thousands of compute jobs. Unfortunately, a small fraction of such jobs regularly fail; the reasons vary from disk and network problems to bugs in the user code. A subset of these failures result in jobs being stuck for long periods of time. In order to debug such failures, interactive monitoring is highly desirable; users need to browse through the job log files and check the status of the running processes. Batch systems typically don't provide such services; at best, users get job logs at job termination, and even this may not be possible if the job is stuck in an infinite loop. In this paper we present a novel approach of using regular batch system capabilities of Condor to enable users to access the logs and processes of any running job. This does not provide true interactive access, so commands like vi are not viable, but it does allow operations like ls, cat, top, ps, lsof, netstat and dumping the stack of any process owned by the user; we call this pseudo-interactive monitoring. It is worth noting that the same method can be used to monitor Grid jobs in a glidein-based environment. We further believe that the same mechanism could be applied to many other batch systems.

  15. accelerating cavity

    CERN Multimedia

    On the inside of the cavity there is a layer of niobium. Operating at 4.2 degrees above absolute zero, the niobium is superconducting and carries an accelerating field of 6 million volts per metre with negligible losses. Each cavity has a surface of 6 m2. The niobium layer is only 1.2 microns thick, ten times thinner than a hair. Such a large area had never been coated to such a high accuracy. A speck of dust could ruin the performance of the whole cavity so the work had to be done in an extremely clean environment.

  16. Beam dump experiments at the AGS

    International Nuclear Information System (INIS)

    Soukas, A.; Bregman, M.; Galik, R.

    1978-01-01

    Searches for the prompt production of weak or semi-strongly interacting particles in a neutrino beam dump and their subsequent interaction or decay were performed at the AGS. The experiment is detailed using the totally active liquid scintillator detector, and mention the results of the spark chamber detector. An exposure of a copper beam dump to two orders of magnitude more protons than in previous searches at 28 GeV has yielded 104 neutrino-like events in the detector. The events from the beam dump are compared directly with those from π and K decay neutrinos produced concurrently in the normal long neutrino decay path following a 15 cm brass target. The characteristics of the events are similar. However, when compared to the rate of events predicted by scaling the 15 cm target yields, the beam dump data show an excess of 45 +- 16 events. The excess events from the beam dump appear to deposit energies greater than or equal to 1 GeV. Their source remains puzzling. Future experiments at the AGS could verify the existence of the effect, decrease the uncertainty in the predicted number of events from 30 to 10% by directly measuring the pion absorption length with a variable density target, search for threshold effects, and measure the sign of the charge of the existing muons. 22 references

  17. radiofrequency cavity

    CERN Multimedia

    1988-01-01

    The pulse of a particle accelerator. 128 of these radio frequency cavities were positioned around CERN's 27-kilometre LEP ring to accelerate electrons and positrons. The acceleration was produced by microwave electric oscillations at 352 MHz. The electrons and positrons were grouped into bunches, like beads on a string, and the copper sphere at the top stored the microwave energy between the passage of individual bunches. This made for valuable energy savings as it reduced the heat generated in the cavity.

  18. Radioactive dumping in the Arctic Ocean

    International Nuclear Information System (INIS)

    Lamb, J.; Gizewski, P.

    1993-01-01

    Recent revelations concerning the possible environmental hazards posed by the sunken Soviet nuclear submarine Komsomolets and the disposal of radioactive materials in the Arctic and North Atlantic oceans have generated much controversy and debate. Too often, however, the key scientific and policy issues that the dumping raises are treated as two solitudes. In reality, decisions taken by national governments and international agencies in connection with remediation, regulation, and even research must be based on both science and policy. Indeed, a sound approach to the dumping issue must integrate scientific evidence and policy considerations relating to legal, political, social, and economic matters. Radioactive waste disposal is an exceedingly difficult problem. Information detailing the Soviet Navy's past dumping practices, and increasing awareness of the problems that Russia and other states may encounter in the future disposal of radioactive waste, indicate that the global inventory of radioactive wastes requiring storage and disposal is large and growing

  19. Dumping the decelerated beams of CLIC

    CERN Document Server

    Jeanneret, Bernard

    2011-01-01

    The spent drive beam must be cleanly extracted and bent away from the decelerator axis at the end of each CLIC decelerator in order to leave space for injecting a fresh beam train in the next sector. Then the spent beam must be safely absorbed. A compact extraction system made of a single dipole is proposed. The spent beam is driven to a water dump located at 20m downstream of the extraction point and transversely 6m away of the axis of the main linac. An adequate spread of the beam impact map on the dump offers small temperature excursions in both the dump and its entrance window, allowing for reliable operation and a long lifetime of the system.

  20. Modernization of dump truck onboard system

    Science.gov (United States)

    Semenov, M. A.; Bolshunova, O. M.; Korzhev, A. A.; Kamyshyan, A. M.

    2017-10-01

    The review of the only automated dispatch system for the career dump trucks, which is presented in the domestic market, was made. A method for upgrading the loading control system and technological weighing process of the career dump was proposed. The cargo weight during loading is determined by the gas pressure in the suspension cylinders at the time of the oscillation ending and at the start of the vibration smoothing process; the smoothing speed correction is performed. The error of the cargo weighting is 2.5-3%, and of the technological weighing process during driving - 1%, which corresponds to the error level of the steady-state weighting means.

  1. ATA diagnostic beam dump conceptual design

    International Nuclear Information System (INIS)

    1981-09-01

    A diagnostic beam dump, able to withstand 72,000 pulses (10 kA, 50 MeV/pulse) per shift was designed and analyzed. The analysis shows that the conceptual beam dump design consisting of 80 vitreous carbon plate-foam elements is able to withstand the thermal and mechanical stresses generated. X-rays produced by bremsstrahlung are absorbed by a three element copper plate-foam x-ray absorber. Cooling between bursts of electron pulses is provided by pressurized helium

  2. Source, transport and dumping of radioactive waste

    International Nuclear Information System (INIS)

    1980-03-01

    The results of an examination into the problems of radioactive waste are presented, in particular the sources, transport and dumping and the policy considerations in favour of specific methods. The theoretical background of radioactive waste is described, including the physical and chemical, ecological, medical and legal aspects. The practical aspects of radioactive waste in the Netherlands are considered, including the sources, the packaging and transport and dumping in the Atlantic Ocean. The politics and policies involved in this process are outlined. (C.F.)

  3. Design studies of the LHC beam dump

    CERN Document Server

    Zazula, J M

    1997-01-01

    This paper is a compilation of the results of the recent 5 years studies of the beam dump system for the LHC proton collider at CERN, with a special emphasis on feasibility of the central absorber. Simulations of energy deposition by particle cascades, optimisation of the beam sweeping system and core layout, and thermal analysis have been completed; the structural deformation, stress and vibration analyses are well advanced, and a new concept of the shielding design has recently been approved. The material characteristics, geometry, performance parameters and safety precautions for different components of the beam dump are actually close to completion, which augurs well for the start of construction work according to schedule.

  4. 30 CFR 57.9301 - Dump site restraints.

    Science.gov (United States)

    2010-07-01

    ... SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Loading, Hauling, and Dumping Safety Devices, Provisions, and Procedures for Roadways, Railroads, and Loading and Dumping Sites...

  5. Combatting social dumping - also an obligation for municipalities

    DEFF Research Database (Denmark)

    Jørgensen, Henning; Baadsgaard, Kelvin

    2018-01-01

    Analytisk indkredsning af social dumping og argumentation for kommuners opgaver i forbindelse med bekæmpelse heraf......Analytisk indkredsning af social dumping og argumentation for kommuners opgaver i forbindelse med bekæmpelse heraf...

  6. Analysis of the London dumping convention

    International Nuclear Information System (INIS)

    Nauke, M.K.

    1983-05-01

    This report gives an in-depth review of the provisions of the London Dumping Convention and of its origins in the context of the international legal framework for controlling all aspects of marine pollution. Particular attention is paid to the provisions concerning radioactive waste. (NEA) [fr

  7. Design of the MI40 beam-abort dump

    International Nuclear Information System (INIS)

    Bhat, C.M.; Martin, P.S.; Russell, A.D.

    1995-05-01

    A beam-abort dump for the Fermilab Main Injector to handle 3E13 protons per pulse at 150 Gev has been designed. A 120 GeV beam line goes through the beam-dump off-set by 27cm from its center. The design and the environmental safety aspects of the beam-dump are described here

  8. Estados de pseudo-Cushing

    OpenAIRE

    Romanholi, Daniella J.P.C.; Salgado, Luiz Roberto

    2007-01-01

    Síndromes de pseudo-Cushing são um grupo heterogêneo de doenças, incluindo alcoolismo, anorexia nervosa, obesidade visceral e depressão, que compartilham muitas das características clínicas e bioquímicas da síndrome de Cushing. Os mecanismos responsáveis para a gênese da síndrome de pseudo-Cushing são fracamente compreendidos. Tem sido sugerido que o hipercortisolismo da síndrome de pseudo-Cushing pode ser resultante do aumento da secreção do hormônio liberador de corticotrofina (CRH) hipotal...

  9. The charged beam dumps for the international linear collider

    CERN Document Server

    Appleby, R; Broome, T; Densham, C; Vincke, H

    2006-01-01

    The baseline configuration of the International Linear Collider requires 2 beam dumps per interaction region, each rated to 18MW of beam power, together with additional beam dumps for tuning purposes and machine protection. The baseline design uses high pressure moving water dumps, first developed for the SLC and used in the TESLA design, although a gas based dump is also being considered. In this paper we discuss the progress made by the international community on both physics and engineering studies for the beam dumps.

  10. Pseudo-Riemannian VSI spaces

    International Nuclear Information System (INIS)

    Hervik, Sigbjoern; Coley, Alan

    2011-01-01

    In this paper we consider pseudo-Riemannian spaces of arbitrary signature for which all of the polynomial curvature invariants vanish (VSI spaces). We discuss an algebraic classification of pseudo-Riemannian spaces in terms of the boost weight decomposition and define the S i - and N-properties, and show that if the curvature tensors of the space possess the N-property, then it is a VSI space. We then use this result to construct a set of metrics that are VSI. All of the VSI spaces constructed possess a geodesic, expansion-free, shear-free, and twist-free null congruence. We also discuss the related Walker metrics.

  11. Design of the LHC beam dump

    International Nuclear Information System (INIS)

    Ferrari, A.; Stevenson, G.R.; Weisse, E.

    1992-01-01

    The severe constraints on the beam dumping system for the proposed Large Hadron Collider (LHC) arising from the beam energy (7.7 TeV) and intensity (5x10 14 protons) call for unusual procedures to dilute the beam. Monte-Carlo cascade simulations which calculated the effectiveness of thin scatterers placed upstream of the main absorber have been corrected and updated. Results are also presented concerning the optimization of the thicknesses of such scatterers. These show that a combined sweeping plus double-scatterer system gives a reasonable safety margin. A system combining the sweeping procedure with a dump where the absorber blocks are interleaved with air gaps could produce comparable dilution of the deposited energy. (author) 6 refs.; 3 figs

  12. Conformal maps between pseudo-Finsler spaces

    Science.gov (United States)

    Voicu, Nicoleta

    The paper aims to initiate a systematic study of conformal mappings between Finsler spacetimes and, more generally, between pseudo-Finsler spaces. This is done by extending several results in pseudo-Riemannian geometry which are necessary for field-theoretical applications and by proposing a technique that reduces some problems involving pseudo-Finslerian conformal vector fields to their pseudo-Riemannian counterparts. Also, we point out, by constructing classes of examples, that conformal groups of flat (locally Minkowskian) pseudo-Finsler spaces can be much richer than both flat Finslerian and pseudo-Euclidean conformal groups.

  13. Results from beam dump experiments at CERN

    International Nuclear Information System (INIS)

    Conforto, G.

    1981-01-01

    Two series of proton beam dump experiments are discussed. One of the main goals of the experiment was to test the hypothesis that neutrinos produced in such a setting arose entirely from charm production followed by either electronic or muonic decay. While much of the data is difficult to interpret, it does appear that this hypothesis is not an adequate explanation of the results, in particular the ratio of electron neutrinos to muon neutrinos

  14. Ion beam dump for JT-60 NBI

    International Nuclear Information System (INIS)

    Kuriyama, Masaaki; Horiike, Hiroshi; Matsuda, Shinzaburo; Morita, Hiroaki; Shibanuma, Kiyoshi

    1981-10-01

    The design of the active cooling type ion beam dump for JT-60 NBI which receives the total beam power of 5.6 MW for 10 sec continuously is described. It is composed of array of many finned tubes which is made of oxygen free copper with 0.2% silver content. The safety margin against thermal and mechanical troubles is estimated by the heat transfer and the thermal stress calculation. (author)

  15. At dumpe på FARMA

    DEFF Research Database (Denmark)

    Johannsen, Bjørn Friis

    Uddrag fra forord: "At dumpe på FARMA peger på flere centrale styrker i farmaceutuddannelsen. For det første at de studerende reelt er interesserede i farmaceutfaget når de optages på studiet, og de oplever velvilje fra underviserne. For det andet at studenterkulturen på studiet er stærk, således...

  16. Dump truck-related deaths in construction, 1992-2007.

    Science.gov (United States)

    McCann, Michael; Cheng, Mei-Tai

    2012-05-01

    Dump trucks are universally used in construction and other industries to haul materials to the location and to remove waste materials. The source for dump truck-related fatality data was the Bureau of Labor Statistics Census of Fatal Occupational Injuries (CFOI) Research File. From 1992 to 2007, 829 construction workers were killed in dump truck-related incidents nationwide. Of those, 336 were dump truck operators with 215 deaths occurring in street and highway incidents. Another 343 deaths involved workers on foot, three-quarters struck by dump trucks. Sixty-four of the construction workers killed were maintaining dump trucks, 22 when caught between the truck frame and a falling dump truck bed. Of the 86 other deaths, 55 involved streets and highways. Recommendations include: (i) improving the reporting of seat belt usage in fatality reports; (ii) requiring use of seat belts; (iii) requiring the use of backup alarms, spotters, or other methods to alert dump truck operators to workers in their blind spots; (iv) prohibiting direct dumping at river banks and embankments; (v) using cameras or radar to enforce stopping at railway crossings; and (xi) enforcing worker safety practices (e.g., lockout/tagout procedures on elevated dump truck beds). Copyright © 2011 Wiley Periodicals, Inc.

  17. Pseudo-Riemannian VSI spaces

    Energy Technology Data Exchange (ETDEWEB)

    Hervik, Sigbjoern [Faculty of Science and Technology, University of Stavanger, N-4036 Stavanger (Norway); Coley, Alan, E-mail: sigbjorn.hervik@uis.no, E-mail: aac@mathstat.dal.ca [Department of Mathematics and Statistics, Dalhousie University, Halifax, Nova Scotia B3H 3J5 (Canada)

    2011-01-07

    In this paper we consider pseudo-Riemannian spaces of arbitrary signature for which all of the polynomial curvature invariants vanish (VSI spaces). We discuss an algebraic classification of pseudo-Riemannian spaces in terms of the boost weight decomposition and define the S{sub i}- and N-properties, and show that if the curvature tensors of the space possess the N-property, then it is a VSI space. We then use this result to construct a set of metrics that are VSI. All of the VSI spaces constructed possess a geodesic, expansion-free, shear-free, and twist-free null congruence. We also discuss the related Walker metrics.

  18. High intensity beam dump for the Tevatron beam abort system

    International Nuclear Information System (INIS)

    Kidd, J.; Mokhov, N.; Murphy, T.; Palmer, M.; Toohig, T.; Turkot, F.; VanGinneken, A.

    1981-01-01

    The beam abort system proposed for the Fermilab Tevatron Accelerator will extract the proton beam from the ring in a single turn (approximately 20/mu/s) and direct it to an external beam dump. It is the function of the beam dump to absorb the unwanted beam and limit the escaping radiation to levels that are acceptable to the surrounding populace and apparatus. A beam dump that is expected to meet these requirements has been designed and constructed. Detailed design of the dump, including considerations leading to the choice of materials, are given. 6 refs

  19. Risks from proposed nuclear waste dump unacceptable

    International Nuclear Information System (INIS)

    Veevers, John

    1999-01-01

    The author has a critical look at the proposal by Pangea Resources Australia Pty Ltd (PARPL) to establish in Australia a permanent underground disposal site for radioactive waste from around the world. In his opinion, the inevitable risk in the proposal stems from the magnitudes: 250,000 tonnes of enormously dangerous RADwaste in the northern hemisphere 20,000 km from its destined dump in Australia, where it must remain intact for at least 10,000 years. These magnitudes - of tonnage, lethality, distance of transport, and time - entail great inherent risk. He also argue that the job of the Australian scientists is to apply due diligence to PARPL proposal

  20. Iodine Beam Dump Design and Fabrication

    Science.gov (United States)

    Polzin, K. A.; Bradley, D. E.

    2017-01-01

    During the testing of electric thrusters, high-energy ions impacting the walls of a vacuum chamber can cause corrosion and/or sputtering of the wall materials, which can damage the chamber walls. The sputtering can also introduce the constituent materials of the chamber walls into an experiment, with those materials potentially migrating back to the test article and coating it with contaminants over time. The typical method employed in this situation is to install a beam dump fabricated from materials that have a lower sputter yield, thus reducing the amount of foreign material that could migrate towards the test article or deposit on anything else present in the vacuum facility.

  1. Fast Dump of the ATLAS Toroids

    CERN Document Server

    Dudarev, A; Volpini, Giovanni; Dudarev, Alexey; Kate, Herman Ten

    2010-01-01

    The toroidal magnet system of the ATLAS Detector at CERN consists of a Barrel Toroid (BT) and two End Cap Toroids (ECT-A and ECT-C). Each toroid is built up from eight racetrack coils wound with an aluminum stabilized NbTi conductor and indirectly cooled by forced flow liquid helium. The three toroids operate in series at 20.5 kA with a total stored energy of 1.5 GJ. In order to verify the reliability and effectiveness of the quench protection system, series of fast dump tests have been performed first of the single toroids and finally of the entire toroidal magnet system. In this paper a model to simulate the fast dump of the ATLAS toroids in single mode operation and in full system configuration is presented. The model is validated through comparison with measured data extracted from the ramp-and-quench runs. The calculated energy dissipation in the various coils is in very good agreement (within 1-2\\%) with the enthalpy changes estimated from the temperature measurements of the different parts of the cold ...

  2. Manufacturing prototypes for LIPAC beam dump

    Energy Technology Data Exchange (ETDEWEB)

    Arranz, F., E-mail: fernando.arranz@ciemat.es [CIEMAT, Madrid (Spain); Brañas, B.; Iglesias, D. [CIEMAT, Madrid (Spain); Nomen, O. [IREC, Barcelona (Spain); Rapisarda, D.; Lapeña, J.; Muñoz, A. [CIEMAT, Madrid (Spain); Szcepaniak, B. [GALVANO-T, Windeck (Germany); Manini, J. [CARMAN, Madrid (Spain); Gómez, J. [TRINOS VACUUM, Valencia (Spain)

    2014-10-15

    Highlights: •Electroforming of copper and electronbeam welding techniques are compared. •Mechanical properties of Cu–stainless steel joint by electroforming are presented. •Achieved manufacturing tolerances are shown. •The difficulties and solutions for the complicated manufacturing are explained. -- Abstract: The purpose of the research is to define the most adequate manufacturing process for the dump of a linear deuteron accelerator. The deuteron beam can be pulsed as well as continuous with energies up to 9 MeV. The maximum beam power is 1.12 MW corresponding to a beam current of 125 mA. The requirements on the surface on which the deuterons will be stopped are quite demanding and the length and slenderness of the cone poses a considerable difficulty in the manufacturing process. The design of the beam dump is based on a copper cone 2500 mm long, 300 mm aperture and 5 to 6.5 mm thickness. Basically only two technologies were found feasible for the manufacturing of the cone: Electroforming and Electron Beam Welding (EBW). The article shows the main results found when manufacturing different prototypes.

  3. Sea-dumped CW munitions - the European component

    International Nuclear Information System (INIS)

    Hart, J.; Stock, T.

    2009-01-01

    The purpose of this contribution is to outline the European magnitude of sea-dumped CW munitions. Hereby the paper attempts to provide an overview on historical dumping activities, both for conventional and chemical munitions. The potential dangers which might result from these dumping activities are discussed in brief. Among others the differences in deep sea dumping and dumping in shallow waters are evaluated. Further, the presentation will outline and discuss the different technology steps: (a) identification, (b) recovery, (c) transportation and (d) destruction (on- or off-shore), necessary for possible cleaning of dumping sites. Thereafter an evaluation of the different technologies available/applied is performed, in particular on the destruction part. Hereby the already practised experience is displayed. Based upon existing treaty regimes an actual judgment of possible application of treaty provisions for demanding cleaning up operations is discussed. The question if treaty obligations can be used to force cleaning operations is debated. A possible match of the technology package available with the scope/magnitude of the munitions dumping problem is discussed. Hereby the gaps between the size of the problem and the most suitable technologies for recovery and destruction are illustrated. The resulting answers should be regarded as possible technical guidelines for future development activities as well existing limitations to solve the problems. The papers will result in some general guidelines for future prospect on the issues of dumped munitions, in particular chemical munitions under the European context.(author)

  4. A model of pyritic oxidation in waste rock dumps

    International Nuclear Information System (INIS)

    Davis, G.B.; Ritchie, A.I.M.

    1983-01-01

    The oxidation of pyrite can lead to high acid levels and high concentrations of trace metals in the water that runs off and percolates through pyritic material. This is the situation at the abandoned uranium mine at Rum Jungle in the Northern Territory of Australia, where pyritic oxidation in the waste rock dumps resulting from open cut mining of the uranium orebody has led to pollution of the nearby East Branch of the Finniss River, with trace metals such as copper, manganese and zinc. Mathematical equations are formulated which describe a model of pyritic oxidation within a waste rock dump, where it is assumed that oxygen transport is the rate limiting step in the oxidation process and that oxygen is transported by gaseous diffusion through the pore space of the dump, followed by diffusion into oxidation sites within the particles that comprise the dump. The equations have been solved numerically assuming values for such parameters as porosity, sulphur density and oxygen diffusion coefficients which are applicable to the waste rock dumps at Rum Jungle. An approximate solution to the equations is also presented. Calculations of the heat source distribution and the total SO 4 production rate are presented for both single size particles and for a range of particle sizes in the dump. The usefulness of the approximate solution, and of calculations based on single size particles in the dump in assessing the effectiveness of strategies to reduce pollution from such waste rock dumps are discussed

  5. 7 CFR 46.22 - Accounting for dumped produce.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Accounting for dumped produce. 46.22 Section 46.22... Market Receivers § 46.22 Accounting for dumped produce. A clear and complete record shall be maintained..., shall be obtained to prove the produce was actually without commercial value, unless there is a specific...

  6. Mineralogy of Tailings Dump around Selebi Phikwe Nickel-Copper ...

    African Journals Online (AJOL)

    This study aimed at mineralogically characterizing the tailings dump emanating from the mining and smelting of nickel-copper (Ni-Cu) at Selebi Phikwe, Botswana, Southern Africa. Samples of tailings dump around the Selebi Phikwe Ni-Cu plant were studied using petrographic microscopy and X-ray Powder Diffraction ...

  7. LHC beam dump system Consequences of abnormal operation

    CERN Document Server

    Kramer, T; Uythoven, J

    2010-01-01

    The LHC beam dump system is one of the most critical systems concerning machine protection and safe operation. It is used to dispose of high intensity beams between 450 GeV and 7 TeV. Studies into the consequences of abnormal beam dump actions have been performed. Different error scenarios have been evaluated using particle tracking in MAD-X, including an asynchronous dump action, and the impact of different orbit and collimator settings. Losses at locations in the ring and the beam dump transfer lines have been quantified as a function of different settings of the dump system protection elements. The implications for the setting up and operation of these protection elements are discussed.

  8. Spoil dump design and rehabilitation management practices (Australia)

    International Nuclear Information System (INIS)

    Goh, E.K.H.; Aspinall, T.O.; Kuszmaul, J.S.

    1998-01-01

    The environmental impact of mining and evolving environmental legislation has been receiving increased attention worldwide in the last two decades. The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental legislative agencies and members of the public. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. There is thus the need to increase the base of knowledge on the existing practices of spoil dump design and rehabilitation. Information concluded from the analysis of the industrial survey carried out on Australian spoil dump management practices at coal, gold and ore mines are presented in this paper. The questionnaire asked for details of soil type of spoils, and factors influencing the design of spoil dumps (climate, rate of erosion, height of dumps, slope gradient and length, overburden handling equipment, soil characteristics, legislation and wastes). 10 refs., 5 figs., 5 tabs

  9. Pressure rise analysis in superconducting coils during dumping

    International Nuclear Information System (INIS)

    Tada, E.; Shimamoto, S.

    1984-01-01

    This chapter describes the ALPHE computer code, whose purpose is to calculate transient helium behavior in a poolboiling coil and to determine suitable characteristics of safety devices to minimize the maximum pressure and the liquid helium lost during dumping due to quench, or when discharging without normalcy. The analysis is compared with the measurements obtained in the domestic test of the Japanese LCT coil. Topics considered include basic equations (helium behavior, heat generation), manual dump without quench, and dumping due to quench. It is demonstrated that the transient behavior, calculated by ALPHE assuming quasi-static equilibrium between helium and coil, is in good agreement with the experimental measurements observed in the domestic test of the Japanese LCT coil. The engineering technique required for the design criteria of superconducting coils and safety device during dumping is established. ALPHE can be used to design an emergency safety system for a helium refrigerator during dumping

  10. Biofertilizers for the revegetation of coal overburden dumps top materials

    Energy Technology Data Exchange (ETDEWEB)

    Nikhil, K. [Central Mining Research Institute, Dhanbad (India). Environmental Management Group

    2001-07-01

    Adding and improving nutrient status of overburden dump top material through biofertilizer for supporting vegetation and for sustainable spoil development, a pot experiment was conducted. In this, two bio-fertilizers namely bactin and phosphin in three doses were applied on overburden dump top material kept in pots growing two grass species. The growths were compared with control on dump and soil both. Results shows that overburden dump amended with bio-fertilizer at lowest dose have significant increase in growth over the control of dump material and soil in vetiver grass but failed to shows the same result in lemon grass. This may be due to different growth behaviour of the grasses. 14 refs., 2 tabs.

  11. Pseudo random signal processing theory and application

    CERN Document Server

    Zepernick, Hans-Jurgen

    2013-01-01

    In recent years, pseudo random signal processing has proven to be a critical enabler of modern communication, information, security and measurement systems. The signal's pseudo random, noise-like properties make it vitally important as a tool for protecting against interference, alleviating multipath propagation and allowing the potential of sharing bandwidth with other users. Taking a practical approach to the topic, this text provides a comprehensive and systematic guide to understanding and using pseudo random signals. Covering theoretical principles, design methodologies and applications

  12. Pseudo-complex general relativity

    CERN Document Server

    Hess, Peter O; Greiner, Walter

    2016-01-01

    This volume presents an pseudo-complex extension of General Relativity which addresses these issues and presents proposals for experimental examinations in strong fields near a large mass. General Relativity is a beautiful and well tested theory of gravitation. Nevertheless, it implies conceptual problems like the creation of singularities (Black Holes) as a result of the collapse of large masses, or the appearance of event horizons which exclude parts of the space-time from the observation of external observers. The mathematical and geometrical foundations of this extension are displayed in detail, and applications including orbits and accretion disks around large central masses, neutron stars or cosmological models are introduced. Calculations both for classical and extended applications are often executed in the form of problems with extensive solutions, which makes this volume also a valuable resource for any student of General Relativity.

  13. Segmented trapped vortex cavity

    Science.gov (United States)

    Grammel, Jr., Leonard Paul (Inventor); Pennekamp, David Lance (Inventor); Winslow, Jr., Ralph Henry (Inventor)

    2010-01-01

    An annular trapped vortex cavity assembly segment comprising includes a cavity forward wall, a cavity aft wall, and a cavity radially outer wall there between defining a cavity segment therein. A cavity opening extends between the forward and aft walls at a radially inner end of the assembly segment. Radially spaced apart pluralities of air injection first and second holes extend through the forward and aft walls respectively. The segment may include first and second expansion joint features at distal first and second ends respectively of the segment. The segment may include a forward subcomponent including the cavity forward wall attached to an aft subcomponent including the cavity aft wall. The forward and aft subcomponents include forward and aft portions of the cavity radially outer wall respectively. A ring of the segments may be circumferentially disposed about an axis to form an annular segmented vortex cavity assembly.

  14. Study of electric phenomena in energy dumping of LCT coil

    International Nuclear Information System (INIS)

    Oka, Koichi; Tsuji, Hiroshi; Nishi, Masataka; Shimamoto, Susumu

    1980-03-01

    In IEA-LCT coil, electric phenomena in energy dumping were studied analytically and experimentally. Protection resistance of the Japanese LCT coil is chosen as 0.1 Ω considering the quenching voltage, so that temperature rise of the coil is no problem. Energy dumping characteristic of the six-coil system is calculated under different conditions. It is concluded that simultaneous dumping of all the coils with the equivalent resistance values of protection is necessary. Flashover voltage tests of the model in 4.2 K liquid helium, 4.2 K gas helium and 4.2 K boiling helium show margin in practical quenching voltage of the coil. (author)

  15. Radiation protection with regard to sea dumping of radioactive waste

    International Nuclear Information System (INIS)

    Sanderse, R.W.; Worst, J.

    1980-01-01

    The Netherlands Energy Research Foundation (ECN) has been dumping into the Atlantic Ocean radioactive waste cast into concrete since 1965. In the report the Health Physics problems with regard to the transport and dumping of the radioactive waste are discussed. In particular to the following points has been paid attention: tasks and working methods of the radiation protection service, dose evaluation for the people involved by two different kinds of dumping methods, doses received by the personal involved, some contamination problems caused by leaking drums. (orig.) [de

  16. Challenges and Plans for Injection and Beam Dump

    Science.gov (United States)

    Barnes, M.; Goddard, B.; Mertens, V.; Uythoven, J.

    The injection and beam dumping systems of the LHC will need to be upgraded to comply with the requirements of operation with the HL-LHC beams. The elements of the injection system concerned are the fixed and movable absorbers which protect the LHC in case of an injection kicker error and the injection kickers themselves. The beam dumping system elements under study are the absorbers which protect the aperture in case of an asynchronous beam dump and the beam absorber block. The operational limits of these elements and the new developments in the context of the HL-LHC project are described.

  17. Guidelines for sea dumping packages of radioactive waste. Revised version.

    International Nuclear Information System (INIS)

    Anon.

    1979-04-01

    The purpose of these Guidelines is to establish general requirements and provide practical information for the design and manufacture of packages for sea dumping of radioactive waste, in accordance with the terms of the OECD Council Decision establishing a Multilateral Consultation and Surveillance Mechanism for Sea Dumping of Radioactive Waste. These Guidelines are in compliance with the IAEA Revised Definition and Recommendations of 1978, for applying the London Dumping Convention to radioactive waste, and are intended for application under the responsibility of the appropriate national authorities of countries participating in the NEA Mechanism

  18. Peabody Western Coal cuts costs with bottom-dump haulers

    Energy Technology Data Exchange (ETDEWEB)

    Perla, S.; Baecker, G.; Morgan, W. [Empire Machinery, Mesa, AZ (United States)

    1995-04-01

    A new hauling concept has been introduced at the Black Mesa and Kayenta coal mines of the Peabody Western Coal Co. in northern Arizona, USA. The article describes the switch from Caterpillar 992 wheel loaders with 136 t bottom-dump trucks to 272 t bottom-dump trucks. Cat 789 off-highway trucks were modified to pull bottom-dump trucks. Haulage costs per ton of coal and cost per ton-mile have fallen significantly since the introduction of the new large hauling method. 7 figs., 2 photos.

  19. New concept for a high-power beam dump

    International Nuclear Information System (INIS)

    Moir, R.W.; Taylor, C.E.

    1980-01-01

    A new concept for a dump for the ion and neutral beams used in the controlled nuclear fusion program uses thin sheets of a refractory metal such as tungsten formed into troughs having semi-circular cross sections. High-velocity water flowing circumferentially removes heat by subcooled nucleate boiling. Possible advantages are modular construction, lower water-pumping power, and a lower pressure drop than in conventional beam dumps. An example design calculation is shown for a dump capable of absorbing an incident flux of 10 kW/cm 2

  20. Beam Dump TIDV #1 - Vacuum Failure of 17 Oct. 97

    CERN Document Server

    Ross, M; CERN. Geneva. SPS and LEP Division

    1997-01-01

    A vacuum leak on the internal beam dump TIDV precipitated its replacement in the LSS1 on Monday the 20th of October 1997, the SPS consequently being shut down for three days. The dump had fulfilled its design function since it was installed in the SPS at the beginning of 1988. Prior to the intervention, the Vacuum Group LHC/VAC carried out a number of leak tests, which led to the decision being taken to replace the dump. After the successful intervention, normal machine operation was resumed. Out-gassing of the ten-year-old replacement was initially high, but vacuum pressure is slowly descending to the SPS standard level.

  1. Practice and assessment of sea dumping of radioactive wastes

    International Nuclear Information System (INIS)

    Templeton, W.L.; Bewers, J.M.

    1985-08-01

    This paper discusses the practice and assessment of the ocean dumping of low-level radioactive wastes. It describes the international and multilateral regulatory framework, the sources, composition, packaging and rate of dumping and, in particular, the recent radiological assessment of the only operational disposal site in the northeast Atlantic. The paper concludes with a discussion of future ocean disposal practices for radioactive wastes, and the application of the approach to the dumping of non-radioactive contaminants in the ocean. 39 refs., 1 fig., 4 tabs

  2. SPIDER beam dump as diagnostic of the particle beam

    Energy Technology Data Exchange (ETDEWEB)

    Zaupa, M., E-mail: matteo.zaupa@igi.cnr.it; Sartori, E. [Università degli Studi di Padova, Via 8 Febbraio 2, Padova 35122 (Italy); Consorzio RFX, Corso Stati Uniti 4, Padova 35127 (Italy); Dalla Palma, M.; Brombin, M.; Pasqualotto, R. [Consorzio RFX, Corso Stati Uniti 4, Padova 35127 (Italy)

    2016-11-15

    The beam power produced by the negative ion source for the production of ion of deuterium extracted from RF plasma is mainly absorbed by the beam dump component which has been designed also for measuring the temperatures on the dumping panels for beam diagnostics. A finite element code has been developed to characterize, by thermo-hydraulic analysis, the sensitivity of the beam dump to the different beam parameters. The results prove the capability of diagnosing the beam divergence and the horizontal misalignment, while the entity of the halo fraction appears hardly detectable without considering the other foreseen diagnostics like tomography and beam emission spectroscopy.

  3. Population dynamics of Pseudo-nitzschia species ...

    African Journals Online (AJOL)

    The genus Pseudo-nitzschia is a chain-forming diatom comprising about 30 species some of which are known to produce domoic acid (DA) that causes amnesic shellfish poisoning (ASP). The current study aimed at assessing the population dynamics of Pseudo-nitzschia in the near shore waters of Dar es Salaam. Samples ...

  4. [Pseudo-Bartter syndrome--2 cases].

    Science.gov (United States)

    Jóźwiak, Lucyna; Jaroszyński, Andrzej; Baranowicz-Gaszczyk, Iwona; Borowicz, Ewa; Ksiazek, Andrzej

    2010-01-01

    Bartter syndrome represents the group of renal disturbances characterized by hypokaliemia and metabolic alkalosis. Some diseases could display hypokalemic metabolic alkalosis without primary tubular dysfunction. These disorders are called pseudo-Bartter syndrome. In this paper we present 2 cases of pseudo-Bartter syndrome related among to other things to overuse of diuretic drugs.

  5. Review of the abort dump shown in the SSC [superconducting super collider] conceptual design report

    International Nuclear Information System (INIS)

    Cossairt, J.D.

    1987-04-01

    This report details the design of the abort dump for the Superconducting Super-Collider (SSC). The dump is made from graphite and designed to absorb the maximum beam energy of 400 MJ. The report considers long time activation effects of the dump components. The report concludes that the basic design of the abort dump is well defined

  6. The IAEA's responsibilities in connection with the dumping at sea of radioactive wastes

    International Nuclear Information System (INIS)

    Ha Vinh Phuong

    1983-01-01

    In the context of IAEA's responsibilities regarding the sea dumping of radioactive wastes, this paper reviews international laws of relevance to sea dumping of wastes, and examines IAEA's role under the London Dumping Convention. The paper also describes the OECD/NEA Multilateral Consultation and Surveillance Mechanism on radioactive waste sea dumping operations. (NEA) [fr

  7. CBP Active Dumping and Active Countervailing (AD/CVD) Cases

    Data.gov (United States)

    Department of Homeland Security — The datasets provide information from CBP's reference files on active anti-dumping and active countervailing cases. This data includes associated case numbers (if...

  8. Continuous Wheel Momentum Dumping Using Magnetic Torquers and Thrusters

    Science.gov (United States)

    Oh, Hwa-Suk; Choi, Wan-Sik; Eun, Jong-Won

    1996-12-01

    Two momentum management schemes using magnetic torquers and thrusters are sug-gested. The stability of the momentum dumping logic is proved at a general attitude equilibrium. Both momentum dumping control laws are implemented with Pulse-Width- Pulse-Frequency Modulated on-off control, and shown working equally well with the original continuous and variable strength control law. Thrusters are assummed to be asymmetrically configured as a contingency case. Each thruster is fired following separated control laws rather than paired thrusting. Null torque thrusting control is added on the thrust control calculated from the momentum control law for the gener-ation of positive thrusting force. Both magnetic and thrusting control laws guarantee the momentum dumping, however, the wheel inner loop control is needed for the "wheel speed" dumping, The control laws are simulated on the KOrea Multi-Purpose SATellite (KOMPSAT) model.

  9. TCDQ-TCT retraction and losses during asynchronous beam dump

    CERN Document Server

    Bracco, Chiara; Quaranta, Elena; CERN. Geneva. ATS Department

    2016-01-01

    The protection provided by the TCDQs in case of asynchronous beam dump depends strongly on their correct setup. They have to respect the strict hierarchy of the full collimation system and shield the tertiary collimators in the experimental regions. This MD aimed at performing asynchronous beam dump tests with different configurations, in order to assess the minimum allowed retraction between TCTs and TCDQs and, as a consequence, on the The protection provided by the TCDQs in case of asynchronous beam dump depends strongly on their correct setup. They have to respect the strict hierarchy of the full collimation system and shield the tertiary collimators in the experimental regions. This MD aimed at performing asynchronous beam dump tests with different configurations, in order to assess the minimum allowed retraction between TCTs and TCDQs and, as a consequence, on the β* reach.

  10. LHC beam dumping system Extraction channel layout and acceptance

    CERN Document Server

    Goddard, B; Uythoven, J; Veness, R; Weterings, W

    2003-01-01

    The LHC beam dumping system must safely abort the LHC beams under all conditions, including those resulting from abnormal behaviour of machine elements or subsystems of the beam dumping system itself. The extraction channels must provide sufficient aperture both for the circulating and extracted beams, over the whole energy range and under various beam parameters. These requirements impose tight constraints on the tolerances of various extraction channel components, and also on the allowed range of beam positions in the region of these components. Operation of the beam dumping system under various fault states has been considered, and the resulting apertures calculated. After describing briefly the beam dumping system and the extraction channel geometry, the various assumptions made in the analysis are presented, before deriving tolerance limits for the relevant equipment and beam parameters.

  11. Chronic intestinal pseudo-obstruction.

    Science.gov (United States)

    Gabbard, Scott L; Lacy, Brian E

    2013-06-01

    Chronic intestinal pseudo-obstruction (CIP) is a rare and serious disorder of the gastrointestinal (GI) tract characterized as a motility disorder with the primary defect of impaired peristalsis; symptoms are consistent with a bowel obstruction, although mechanical obstruction cannot be identified. CIP is classified as a neuropathy, myopathy, or mesenchymopathy; it is a neuropathic process in the majority of patients. The natural history of CIP is generally that of a progressive disorder, although occasional patients with secondary CIP note significant symptomatic improvement when the underlying disorder is identified and treated. Symptoms vary from patient to patient depending on the location of the luminal GI tract involved and the degree of involvement; however, the small intestine is nearly always involved. Common symptoms include dysphagia, gastroesophageal reflux, abdominal pain, nausea, vomiting, bloating, abdominal distension, constipation or diarrhea, and involuntary weight loss. Unfortunately, these symptoms are nonspecific, which can contribute to misdiagnosis or a delay in diagnosis and treatment. Since many of the symptoms and signs suggest a mechanical bowel obstruction, diagnostic tests typically focus on uncovering a mechanical obstruction, although routine tests do not identify an obstructive process. Nutrition supplementation is required for many patients with CIP due to symptoms of dysphagia, nausea, vomiting, and weight loss. This review discusses the epidemiology, etiology, pathogenesis, diagnosis, and treatment of patients with CIP, with an emphasis on nutrition assessment and treatment options for patients with nutrition compromise.

  12. Results from the LHC Beam Dump Reliability Run

    CERN Document Server

    Uythoven, J; Carlier, E; Castronuovo, F; Ducimetière, L; Gallet, E; Goddard, B; Magnin, N; Verhagen, H

    2008-01-01

    The LHC Beam Dumping System is one of the vital elements of the LHC Machine Protection System and has to operate reliably every time a beam dump request is made. Detailed dependability calculations have been made, resulting in expected rates for the different system failure modes. A 'reliability run' of the whole system, installed in its final configuration in the LHC, has been made to discover infant mortality problems and to compare the occurrence of the measured failure modes with their calculations.

  13. Conversion of waste dump into a recreation and leisure park

    International Nuclear Information System (INIS)

    Petit, E.; Martens, P.N.

    1997-01-01

    In a two year strategy-project Aachen University investigated possibilities for postmining activities for a German coal mine. All research work was based on existing infrastructure and mine related potentials. One of the potentials is the waste dump with a height of 90 m above surface and 40 ha in size. This paper deals with the idea of converting the dump into a recreation and leisure park with greater than regional significance. 3 refs., 4 figs

  14. Possibilities for stabilization of fly ash from REK 'Bitola' dump

    International Nuclear Information System (INIS)

    Petrushevska, Ljubica; Ivanovska, Pavlina; Ilievski, Zlatko; Peeva, Liljana

    2002-01-01

    The Coal Power Plants environmental problems, mainly, arise from deposited fly ash-solid particles which, under the influence of the wind, heavily pollute the atmospheric air. Prevention of the environmental problems, coming from spraying from the energetic dumps, is achieved with technical and biological stabilization of dumped fly ash. The choice of the stabilization means and methods depends on the physical-chemical properties of the ash. Therefore, the stabilization possibilities of REK 'Bitola' fly ash were investigated. (Original)

  15. Geoelectrical Evaluation of Waste Dump Sites at Warri and its ...

    African Journals Online (AJOL)

    The existing waste dump sites in Delta State were investigated without soil disturbance by using the vertical electrical sounding (VES).The soil overlying the aquifer at Ovwian-Aladja dump site has resistively values, 11.84-85.50 Ohm-m, thicknesses,21.10-31.83m and at depths less than 1m, while at Warri it has resistively ...

  16. Pseudo-Haptic Feedback in Teleoperation.

    Science.gov (United States)

    Neupert, Carsten; Matich, Sebastian; Scherping, Nick; Kupnik, Mario; Werthschutzky, Roland; Hatzfeld, Christian

    2016-01-01

    In this paper, we develop possible realizations of pseudo-haptic feedback in teleoperation systems based on existing works for pseudo-haptic feedback in virtual reality and the intended applications. We derive four potential factors affecting the performance of haptic feedback (calculation operator, maximum displacement, offset force, and scaling factor), which are analyzed in three compliance identification experiments. First, we analyze the principle usability of pseudo-haptic feedback by comparing information transfer measures for teleoperation and direct interaction. Pseudo-haptic interaction yields well above-chance performance, while direct interaction performs almost perfectly. In order to optimize pseudo-haptic feedback, in the second study we perform a full-factorial experimental design with 36 subjects performing 6,480 trials with 36 different treatments. Information transfer ranges from 0.68 bit to 1.72 bit in a task with a theoretical maximum of 2.6 bit, with a predominant effect of the calculation operator and a minor effect of the maximum displacement. In a third study, short- and long-term learning effects are analyzed. Learning effects regarding the performance of pseudo-haptic feedback cannot be observed for single-day experiments. Tests over 10 days show a maximum increase in information transfer of 0.8 bit. The results show the feasibility of pseudo-haptic feedback for teleoperation and can be used as design basis for task-specific systems.

  17. Dump evaluation for landscape restoration of an ancient cacareous quarry

    International Nuclear Information System (INIS)

    Paredes, R.; Ayala, R.; Trevisiol, S.

    2010-01-01

    This work is about the geological - mining study in the limestone quarry in the west of Valle Hermoso town - Cordoba - Argentina. The generation of dump material is considered a waste but is inherent to the process of rocks and minerals extraction. The dump stocks evaluation take into account the different types of rocks with physical and chemical characteristics. The dump has several carbonatic qualities and can be given useful to uncover material originally dismissed as to be used as crushed stone for concrete and others.The reuse of this waste can be allocated primarily to the construction industry, and explore other potential uses, would rehabilitate these lands, and thus eliminate an environmental liability .This work is about the geological - mining study in the limestone quarry in the west of Valle Hermoso town - Cordoba - Argentina. The generation of dump material is considered a waste but is inherent to the process of rocks and minerals extraction. The dump stocks evaluation take into account the different types of rocks with physical and chemical characteristics. The dump has several carbonatic qualities and can be given useful to uncover material originally dismissed as to be used as crushed stone for concrete and others.The reuse of this waste can be allocated primarily to the construction industry, and explore other potential uses, would rehabilitate these lands, and thus eliminate an environmental liability

  18. Experience with dose limitation during preparations for sea dumping operations

    International Nuclear Information System (INIS)

    Fieuw, G.; Voorde, N. van de; Baekelandt, L.

    1982-01-01

    Since 1967 low-level radioactive wastes from operational nuclear facilities in Belgium have been dumped into the sea. The dumping is carried out in accordance with the recommendations issued by the IAEA under the London Convention. All these dumping operations have taken place under the surveillance of the Nuclear Energy Agency of the OECD. To limit the doses received by workers and the public during the various phases leading up to sea dumping, appropriate measures are required in connection with waste treatment and packaging, limitation of radiation levels, storage and handling, organization and selection of the means of transport and organization and means of monitoring. Although treatment and handling at the nuclear sites are entrusted to occupationally exposed workers, temporary labour is used for the transport and handling operations. Effective treatment and packaging reduce the risk of internal exposure to a negligible value. Meticulous planning and permanent personnel monitoring reduce the doses received by the workers to acceptable values not exceeding the statutory dose limits. The doses received by personnel involved in the preparations for sea dumping operations from 1967 to 1980 are given and a relationship is established between these doses and the activities handled. Experience shows that sea dumping operations do not entail unacceptable risks either for the workers concerned or for the population and allows us to optimize the methods used for loading, handling and transport. (author)

  19. Radioactive-waste ocean dumping will have negligible enviromental impact

    International Nuclear Information System (INIS)

    Anon.

    1976-01-01

    This draft report is the result of extensive studies based on the best available information in the field of oceanography, marine radiobiology and health physics. On various basic considerations, assessment was undertaken, and the following conclusion was reached. The quantity of radioactivity to be dumped at one time is assumed to be 500 Ci in the case of test dumping, and 10 5 Ci/year in the case of full-scale dumping. The conditions required for the dumping sea area are that the bottom water flow and upwelling amount are limited, and that the sea bottom is flat. The horizontal dispersion coefficient of 10 7 cm 2 /sec and the vertical dispersion coefficient of 2 x 10 2 cm 2 /sec are assumed. It is assumed that the radionuclides in the disposed package would leached out as soon as it reaches the sea bottom, and would not show any physicochemical behavior. Typycal radionuclides are classified into 5 groups in terms of their half lives, and their estimated concentrations at 1 km depth are tabulated. The maximum level of individual dose and the magnitude of population dose were assessed on the fishermen working in the dumping sea area, and the adults, children and infants who were expected to receive higher dose on account of the larger intake of fish products than average. The dose level given with the dose assessment model and various panamentors under the dumping conditions is much lower than natural radiation and the permissible level recommended by ICRP. (Kobatake, H.)

  20. Chevron beam dump for ITER edge Thomson scattering system

    International Nuclear Information System (INIS)

    Yatsuka, E.; Hatae, T.; Bassan, M.; Itami, K.; Vayakis, G.

    2013-01-01

    This paper contains the design of the beam dump for the ITER edge Thomson scattering system and mainly concerns its lifetime under the harsh thermal and electromagnetic loads as well as tight space allocation. The lifetime was estimated from the multi-pulse laser-induced damage threshold. In order to extend its lifetime, the structure of the beam dump was optimized. A number of bent sheets aligned parallel in the beam dump form a shape called a chevron which enables it to avoid the concentration of the incident laser pulse energy. The chevron beam dump is expected to withstand thermal loads due to nuclear heating, radiation from the plasma, and numerous incident laser pulses throughout the entire ITER project with a reasonable margin for the peak factor of the beam profile. Structural analysis was also carried out in case of electromagnetic loads during a disruption. Moreover, detailed issues for more accurate assessments of the beam dump's lifetime are clarified. Variation of the bi-directional reflection distribution function (BRDF) due to erosion by or contamination of neutral particles derived from the plasma is one of the most critical issues that needs to be resolved. In this paper, the BRDF was assumed, and the total amount of stray light and the absorbed laser energy profile on the beam dump were evaluated

  1. Chevron beam dump for ITER edge Thomson scattering system

    Energy Technology Data Exchange (ETDEWEB)

    Yatsuka, E.; Hatae, T.; Bassan, M.; Itami, K. [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan); Vayakis, G. [ITER Organization, 13115 St Paul Lez Durance Cedex (France)

    2013-10-15

    This paper contains the design of the beam dump for the ITER edge Thomson scattering system and mainly concerns its lifetime under the harsh thermal and electromagnetic loads as well as tight space allocation. The lifetime was estimated from the multi-pulse laser-induced damage threshold. In order to extend its lifetime, the structure of the beam dump was optimized. A number of bent sheets aligned parallel in the beam dump form a shape called a chevron which enables it to avoid the concentration of the incident laser pulse energy. The chevron beam dump is expected to withstand thermal loads due to nuclear heating, radiation from the plasma, and numerous incident laser pulses throughout the entire ITER project with a reasonable margin for the peak factor of the beam profile. Structural analysis was also carried out in case of electromagnetic loads during a disruption. Moreover, detailed issues for more accurate assessments of the beam dump's lifetime are clarified. Variation of the bi-directional reflection distribution function (BRDF) due to erosion by or contamination of neutral particles derived from the plasma is one of the most critical issues that needs to be resolved. In this paper, the BRDF was assumed, and the total amount of stray light and the absorbed laser energy profile on the beam dump were evaluated.

  2. Chevron beam dump for ITER edge Thomson scattering system.

    Science.gov (United States)

    Yatsuka, E; Hatae, T; Vayakis, G; Bassan, M; Itami, K

    2013-10-01

    This paper contains the design of the beam dump for the ITER edge Thomson scattering system and mainly concerns its lifetime under the harsh thermal and electromagnetic loads as well as tight space allocation. The lifetime was estimated from the multi-pulse laser-induced damage threshold. In order to extend its lifetime, the structure of the beam dump was optimized. A number of bent sheets aligned parallel in the beam dump form a shape called a chevron which enables it to avoid the concentration of the incident laser pulse energy. The chevron beam dump is expected to withstand thermal loads due to nuclear heating, radiation from the plasma, and numerous incident laser pulses throughout the entire ITER project with a reasonable margin for the peak factor of the beam profile. Structural analysis was also carried out in case of electromagnetic loads during a disruption. Moreover, detailed issues for more accurate assessments of the beam dump's lifetime are clarified. Variation of the bi-directional reflection distribution function (BRDF) due to erosion by or contamination of neutral particles derived from the plasma is one of the most critical issues that needs to be resolved. In this paper, the BRDF was assumed, and the total amount of stray light and the absorbed laser energy profile on the beam dump were evaluated.

  3. Newtonian and pseudo-Newtonian Hill problem

    International Nuclear Information System (INIS)

    Steklain, A.F.; Letelier, P.S.

    2006-01-01

    A pseudo-Newtonian Hill problem based on the Paczynski-Wiita pseudo-Newtonian potential that reproduces general relativistic effects is presented and compared with the usual Newtonian Hill problem. Poincare maps, Lyapunov exponents and fractal escape techniques are employed to study bounded and unbounded orbits. In particular we consider the systems composed by Sun, Earth and Moon and composed by the Milky Way, the M2 cluster and a star. We find that some pseudo-Newtonian systems-including the M2 system-are more stable than their Newtonian equivalent

  4. Management of dumping of packaged low-level wastes in the deep ocean with emphasis on the North East Atlantic dump site

    International Nuclear Information System (INIS)

    Templeton, W.L.

    1981-08-01

    The following aspects are discussed: radiological principles as applied to disposal to the environment; international regulations; historical dumping practices; assessment of the Northeast Atlantic dump site; IAEA generic studies; and implications of issues on US needs and policies

  5. Sea dumping of radioactive wastes. Part 3: Dumping practice and radioecology

    International Nuclear Information System (INIS)

    Krejsa, P.

    1983-04-01

    Sea dumping of low level radioactive waste is a disposal method practised by a number of states, controlled by OECD/NEA. It makes use of the capacity of the oceans to dilute the radionuclides to levels acceptable concerning resulting dose burdens. For the determination of release rates some oceanographic model have been developed, describing the physical behaviour of the released radionuclides. It is not to be assumed that a complete mathematical description of the involved processes can be made. Too many parameters are dependent and varying as there is the chemical behaviour of different valence states, complexing agents, distribution patterns etc. But it can be seen that the existing description methods allow the adequate modelling of the short and the long term behaviour of the radionuclides. The use of pessimistic assumptions for distribution and reconcentration is sufficient to consider uncertainties of the model. Therefore the arguments of Greenpeace, kindly submitted by this organisation for this study, show no open question, which has not been considered on the sea dumping procedures under surveillance of the OECD/NEA. (Author)

  6. Generation of pulsed light in the visible spectral region based on non-linear cavity dumping

    DEFF Research Database (Denmark)

    Johansson, Sandra; Andersen, Martin; Tidemand-Lichtenberg, Peter

    of 215 kHz. Both lasers were pumped with 808 nm laser diodes delivering 4 W of output power. The circulating power of the 1342 nm laser was 57 W and the peak power of the 1064 nm laser reaching the PPKTP crystal was 17 W. A peak power of approximately 4 W at 593 nm was measured. Accounting...

  7. Uncoupled thermoelasticity solutions applied on beam dumps

    Directory of Open Access Journals (Sweden)

    A. Ouzia

    2016-06-01

    Full Text Available In particle accelerators the process of beam absorption is vital. At CERN particle beams are accelerated at energies of the order of TeV. In the event of a system failure or following collisions, the beam needs to be safely absorbed by dedicated protecting blocks. The thermal shock caused by the rapid energy deposition within the absorbing block causes thermal stresses that may rise above critical levels. The present paper provides a convenient expression of such stresses under hypotheses described hereafter. The temperature field caused by the beam energy deposition is assumed to be Gaussian. Such a field models a non-diffusive heat deposition. These effects are described as thermoelastic as long as the stresses remain below the proportional limit and can be analytically modeled by the coupled equations of thermoelasticity. The analytical solution to the uncoupled thermoelastic problem in an infinite domain is presented herein and matched with a finite unit radius sphere. The assumption of zero diffusion as well as the validity of the match with a finite geometry is quantified such that the obtained solutions can be rigorously applied to real problems. Furthermore, truncated series solutions, which are not novel, are used for comparison purposes. All quantities are nondimensional and the problem reduces to a dependence of five dimensionless parameters. The equations of elasticity are presented in the potential formulation where the shear potential is assumed to be nil due to the source being a gradient and the absence of boundaries. Nevertheless equivalent three-dimensional stresses are computed using the compressive potential and optimized using standard analytical optimization methods. An alternative algorithm for finding the critical points of the three-dimensional stress function is presented. Finally, a case study concerning the proton synchrotron booster dump is presented where the aforementioned analytical solutions are used and the

  8. Pseudo-Kaehler quantization on flag manifolds

    International Nuclear Information System (INIS)

    Karabegov, A.V.

    1997-07-01

    A unified approach to geometric, symbol and deformation quantizations on a generalized flag manifold endowed with an invariant pseudo-Kaehler structure is proposed. In particular cases we arrive at Berezin's quantization via covariant and contravariant symbols. (author). 16 refs

  9. POPULATION DYNAMICS OF PSEUDO-NITZSCHIA SPECIES ...

    African Journals Online (AJOL)

    nb

    current study aimed at assessing the population dynamics of Pseudo-nitzschia ... and to the developing aquaculture industry ... B. Hotel. Pangani Island. Bongoyo Island. Mbudya Island. Msasani Bay ... Salinity values did not show clear trends.

  10. Improved reactor cavity

    International Nuclear Information System (INIS)

    Katz, L.R.; Demarchais, W.E.

    1984-01-01

    A reactor pressure vessel disposed in a cavity has coolant inlet or outlet pipes extending through passages in the cavity walls and welded to pressure nozzles. The cavity wall has means for directing fluid away from a break at a weld away from the pressure vessel, and means for inhibiting flow of fluid toward the vessel. (author)

  11. Modelling reactive transport in a phosphogypsum dump, Venezia, Italia

    Science.gov (United States)

    Calcara, Massimo; Borgia, Andrea; Cattaneo, Laura; Bartolo, Sergio; Clemente, Gianni; Glauco Amoroso, Carlo; Lo Re, Fabio; Tozzato, Elena

    2013-04-01

    We develop a reactive-transport porous media flow model for a phosphogypsum dump located on the intertidal deposits of the Venetian Lagoon: 1. we construct a complex conceptual and geologic model from field data using the GMS™ graphical user interface; 2. the geological model is mapped onto a rectangular MODFLOW grid; 3. using the TMT2 FORTRAN90 code we translate this grid into the MESH, INCON and GENER input files for the TOUGH2 series of codes; 4. we run TOUGH-REACT to model flow and reactive transport in the dump and the sediments below it. The model includes 3 different dump materials (phosphogypsum, bituminous and hazardous wastes) with the pores saturated by specific fluids. The sediments below the dump are formed by an intertidal sequence of calcareous sands and silts, in addition to clays and organic deposits, all of which are initially saturated with lagoon salty waters. The recharge rain-water dilutes the dump fluids. In turn, the percolates from the dump react with the underlying sediments and the sea water that saturates them. Simulation results have been compared with chemical sampled analyses. In fact, in spite of the simplicity of our model we are able to show how the pH becomes neutral at a short distance below the dump, a fact observed during aquifer monitoring. The spatial and temporal evolution of dissolution and precipitation reactions occur in our model much alike reality. Mobility of some elements, such as divalent iron, are reduced by specific and concurrent conditions of pH from near-neutrality to moderately high values and positive redox potential; opposite conditions favour mobility of potentially toxic metals such as Cr, As Cd and Pb. Vertical movement are predominant. Trend should be therefore heavily influenced by pH and Eh values. If conditions are favourable to mobility, concentration of these substances in the bottom strata could be high. However, simulation suggest that the sediments tend to reduce the transport potential of

  12. Preliminary design of the new Proton Synchrotron Internal Dump core

    CERN Document Server

    AUTHOR|(CDS)2091975; Nuiry, François-Xavier

    The luminosity of the LHC particle accelerator at CERN is planned to be upgraded in the first half of 2020s, requiring also the upgrade of its injector accelerators, including the Proton Synchrotron (PS). The PS Internal Dumps are beam dumps located in the PS accelerator ring. They are safety devices designed to stop the circulating proton beam in order to protect the accelerator from damage due to an uncontrolled beam loss. The PS Internal Dumps need to be upgraded to be able to withstand the future higher intensity and energy proton beams. The dump core is a block of material interacting with the beam. It is located in ultra-high vacuum and moved into the beam path in 150 milliseconds by an electromagnet and spring-based actuation mechanism. The circulating proton beam is shaved by the core surface during thousands of beam revolutions. The preliminary new dump core design weighs 13 kilograms and consists of an isostatically pressed fine-grain graphite and a precipitation hardened copper alloy CuCrZr. The ...

  13. Pseudo-color processing in nuclear medical image

    International Nuclear Information System (INIS)

    Wang Zhiqian; Jin Yongjie

    1992-01-01

    The application of pseudo-color technology in nuclear medical image processing is discussed. It includes selection of the number of pseudo-colors, method of realizing pseudo-color transformation, function of pseudo-color transformation and operation on the function

  14. Algebra of pseudo-differential C*-operators

    International Nuclear Information System (INIS)

    Mohammad, N.

    1987-11-01

    In this paper the algebra of pseudo-differential operators is studied in the framework of C * -algebras. It is proved that every pseudo-differential operator of order m admits an adjoint operator, in this case, which is again a pseudo-differential operator. Consequently, the space of all pseudo-differential operators on a compact manifold is an involutive algebra. 10 refs

  15. THE PSEUDO-EVOLUTION OF HALO MASS

    International Nuclear Information System (INIS)

    Diemer, Benedikt; Kravtsov, Andrey V.; More, Surhud

    2013-01-01

    A dark matter halo is commonly defined as a spherical overdensity of matter with respect to a reference density, such as the critical density or the mean matter density of the universe. Such definitions can lead to a spurious pseudo-evolution of halo mass simply due to redshift evolution of the reference density, even if its physical density profile remains constant over time. We estimate the amount of such pseudo-evolution of mass between z = 1 and 0 for halos identified in a large N-body simulation, and show that it accounts for almost the entire mass evolution of the majority of halos with M 200ρ-bar ≲ 10 12 h -1 M ☉ and can be a significant fraction of the apparent mass growth even for cluster-sized halos. We estimate the magnitude of the pseudo-evolution assuming that halo density profiles remain static in physical coordinates, and show that this simple model predicts the pseudo-evolution of halos identified in numerical simulations to good accuracy, albeit with significant scatter. We discuss the impact of pseudo-evolution on the evolution of the halo mass function and show that the non-evolution of the low-mass end of the halo mass function is the result of a fortuitous cancellation between pseudo-evolution and the absorption of small halos into larger hosts. We also show that the evolution of the low-mass end of the concentration-mass relation observed in simulations is almost entirely due to the pseudo-evolution of mass. Finally, we discuss the implications of our results for the interpretation of the evolution of various scaling relations between the observable properties of galaxies and galaxy clusters and their halo masses.

  16. The radiation hazard from the tantalum dumps in Penang

    International Nuclear Information System (INIS)

    1989-01-01

    The radiation level at the dumps are well above background. The readings taken on the dumps themselves range from 1000 mrem/year to 5860 mrem/year. The radiation levels in the houses close to the dump at Hill Railway Road were much lower, in the range of 160 mrem/year to 335 mrem/year. However, the level recorded at a house on Medan Tembaga is higher, being around 650 mrem/year. It is worth noting that the maximum permissible dose as recommended by the International Commission on Radiological Protection for the general public is 500 mrem/year and the average background radiation level is around 80-90 mrem/year. (author)

  17. Protection coverage parameters indentification for uranium tailing dumps

    International Nuclear Information System (INIS)

    Khakimov, N.; Nazarov, Kh.M.; Mirsaidov, I.U.; Akhmedov, M.Z.

    2012-01-01

    This article is devoted to protection coverage parameters indentification for uranium tailing dumps. Authors noticed that many tailing dumps In Tajikistan do not correspond to modern requirements of territories remediation published by IAEA and current norms of the Republic of Tajikistan. The most dangerous is radionuclide migration i.e., distribution of radioactive substances beyond the uranium tailing dumps territories. One of the basic distribution ways is atmospheric migration. At the same time potentially dangerous factors are: dust rising from open surfaces is the source for contamination distribution to neighboring territories; direct external exposure of public located in close distance to the sites; radioactive gas radon exhalation originating a threat if radionuclides penetration to the human body through breathing passages. Different methods of tailing's negative impact minimization, including coverage with neutral soil layer, coverage with fine-ground worked-out bentonite clay were proposed.

  18. Recultivation of mining waste dumps in the Ruhr area, Germany

    International Nuclear Information System (INIS)

    Schulz, D.

    1996-01-01

    In 1993 Ruhrkohle AG produced 41.9 million tons of coal and 19.1 million m 3 of mining waste. Of this, 0.7 million m 3 were used underground as stowing material, 4.7 million m 3 was used commercially, while the remaining 13.7 million m 3 required dumping. Efforts related to the use and disposal of the material up to now dumped are concentrating on applying technical methods to reduce the production of waste underground, on opening up new markets of this material, on utilization of mining waste as a building material, and on low-environmental-impact dumping. Since the late 1970s, the mining waste heaps in the Ruhr mining region have been conceived and designed as landscape structures, i.e. they are integrated into the landscape by means of careful planning and design, and are immediately planted with vegetation. 9 refs., 5 figs

  19. A high average power beam dump for an electron accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xianghong, E-mail: xl66@cornell.edu [Cornell Laboratory of Accelerator-based Sciences and Education, Cornell University, Ithaca, NY 14853 (United States); Bazarov, Ivan; Dunham, Bruce M.; Kostroun, Vaclav O.; Li, Yulin; Smolenski, Karl W. [Cornell Laboratory of Accelerator-based Sciences and Education, Cornell University, Ithaca, NY 14853 (United States)

    2013-05-01

    The electron beam dump for Cornell University's Energy Recovery Linac (ERL) prototype injector was designed and manufactured to absorb 600 kW of electron beam power at beam energies between 5 and 15 MeV. It is constructed from an aluminum alloy using a cylindrical/conical geometry, with water cooling channels between an inner vacuum chamber and an outer jacket. The electron beam is defocused and its centroid is rastered around the axis of the dump to dilute the power density. A flexible joint connects the inner body and the outer jacket to minimize thermal stress. A quadrant detector at the entrance to the dump monitors the electron beam position and rastering. Electron scattering calculations, thermal and thermomechanical stress analysis, and radiation calculations are presented.

  20. Upgrade of the LHC Beam Dumping Protection Elements

    CERN Document Server

    Weterings, W; Balhan, B; Borburgh, J; Goddard, B; Maglioni, C; Versaci, R

    2012-01-01

    The Beam Dumping System for the Large Hadron Collider comprises for each ring a set of horizontally deflecting extraction kicker magnets, vertically deflecting steel septa, dilution kickers and finally, a couple of hundred meters further downstream, an absorber block. A mobile diluter (TCDQ) protects the superconducting quadrupole immediately downstream of the extraction as well as the arc at injection energy and the triplet aperture at top energy from bunches with small impact parameters, in case of a beam dump that is not synchronized with the particle free gap or a spontaneous firing of the extraction kickers. Simulations have shown that an asynchronous dump of a 7 TeV nominal beam into the TCDQ absorber blocks could damage it. This paper describes the proposed changes to this device in order to maintain the protection for the downstream elements while reducing the risk of damaging the TCDQ in case of such a beam loss.

  1. SEARCHING FOR LOW WEIGHT PSEUDO-CODEWORDS

    International Nuclear Information System (INIS)

    Chertkov, Michael; Stepanov, Mikhail

    2007-01-01

    Belief Propagation (BP) and Linear Programming (LP) decodings of LDPC codes are discussed. The authors summarize results of instanton/pseudo-codeword approach developed for analysis of the error-floor domain of the codes. Instantons are special, code and decoding specific, configurations of the channel noise contributing most to the Frame-Error-Rate (FER). Instantons are decoded into pseudo-codewords. Instanton/pseudo-codeword with the lowest weight describes the largest Signal-to-Noise-Ratio (SNR) asymptotic of FER, while the whole spectra of the low weight instantons is descriptive of the FER vs. SNR profile in the extended error-floor domain. First, they describe a general optimization method that allows to find the instantons for any coding/decoding. Second, they introduce LP-specific pseudo-codeword search algorithm that allows efficient calculations of the pseudo-codeword spectra. Finally, they discuss results of combined BP/LP error-floor exploration experiments for two mode codes.

  2. Maintaining heterokaryosis in pseudo-homothallic fungi.

    Science.gov (United States)

    Grognet, Pierre; Silar, Philippe

    2015-01-01

    Among all the strategies displayed by fungi to reproduce and propagate, some species have adopted a peculiar behavior called pseudo-homothallism. Pseudo-homothallic fungi are true heterothallics, i.e., they need 2 genetically-compatible partners to mate, but they produce self-fertile mycelium in which the 2 different nuclei carrying the compatible mating types are present. This lifestyle not only enables the fungus to reproduce without finding a compatible partner, but also to cross with any mate it may encounter. However, to be fully functional, pseudo-homothallism requires maintaining heterokaryosis at every stage of the life cycle. We recently showed that neither the structure of the mating-type locus nor hybrid-enhancing effect due to the presence of the 2 mating types accounts for the maintenance of heterokaryosis in the pseudo-homothallic fungus P. anserina. In this addendum, we summarize the mechanisms creating heterokaryosis in P. anserina and 2 other well-known pseudo-homothallic fungi, Neurospora tetrasperma and Agaricus bisporus. We also discuss mechanisms potentially involved in maintaining heterokaryosis in these 3 species.

  3. SEARCHING FOR LOW WEIGHT PSEUDO-CODEWORDS

    Energy Technology Data Exchange (ETDEWEB)

    CHERTKOV, MICHAEL [Los Alamos National Laboratory; STEPANOV, MIKHAIL [Los Alamos National Laboratory

    2007-01-23

    Belief Propagation (BP) and Linear Programming (LP) decodings of LDPC codes are discussed. The authors summarize results of instanton/pseudo-codeword approach developed for analysis of the error-floor domain of the codes. Instantons are special, code and decoding specific, configurations of the channel noise contributing most to the Frame-Error-Rate (FER). Instantons are decoded into pseudo-codewords. Instanton/pseudo-codeword with the lowest weight describes the largest Signal-to-Noise-Ratio (SNR) asymptotic of FER, while the whole spectra of the low weight instantons is descriptive of the FER vs. SNR profile in the extended error-floor domain. First, they describe a general optimization method that allows to find the instantons for any coding/decoding. Second, they introduce LP-specific pseudo-codeword search algorithm that allows efficient calculations of the pseudo-codeword spectra. Finally, they discuss results of combined BP/LP error-floor exploration experiments for two mode codes.

  4. Optimization of Front Axle Suspension System of Articulated Dump Truck

    DEFF Research Database (Denmark)

    Langer, Thomas Heegaard; Christensen, Brian B.; Mouritsen, Ole Ø.

    2010-01-01

    that has been subjected to comfort improvement is a two axle articulated dump truck. The comfort has been in terms of whole body vibration exposure and the overall improvement has been made possible by adding front axle suspension. However, a hydraulic stabilizing system between the tractor and trailer...... to evaluate the whole body vibrations. By use of a multibody simulation model of the dump truck the whole body vibration exposure has been computed using the predefined work cycle as model input. The design parameters comprise the components of the hydraulic subsystem of the suspension, i.e., the size...

  5. Phytoremediation of spoil coal dumps in Western Donbass (Ukraine)

    Science.gov (United States)

    Klimkina, Iryna; Kharytonov, Mykola; Wiche, Oliver; Heilmeier, Hermann

    2017-04-01

    At the moment, in Ukraine about 150 thousand hectares of fertile land are occupied by spoil dumps. Moreover, this figure increases every year. According to the technology used about 1500 m3 of adjacent stratum is dumped at the surface per every 1000 tons of coal mined. Apart from land amortization, waste dumps drastically change the natural landscape and pollute air, soil and water sources as the result of water and wind erosion, as well as self-ignition processes. A serious concern exists with respect to the Western Donbass coal mining region in Ukraine, where the coal extraction is made by the subsurface way and solid wastes are represented by both spoil dumps and wastes after coal processing. Sulphides, mostly pyrite (up to 4% of waste material), are widely distributed in the waste heaps freshly removed due to coal mining in Western Donbass.The oxidation of pyrite with the presence of oxygen and water is accompanied by a sharp drop in the pH from the surface layer to the spoil dumps(from 5.2-6.2 to 3.9-4.2 in soil substrates with chernozen and from 8.3-8.4 to 6.7-7.2 in soil substrates with red-brown clay, stabilizing in dump material in both cases at 2.9-3.2). Low pH generates the transformation of a number of toxic metals and other elementspresent in waste rock (e.g. Fe, Al, Mn, Zn, Mo, Co, As, Cd, Bi, Pb, U) into mobile forms. To stabilize and reduce metal mobility the most resistant plants that occur naturally in specified ecosystems can be used. On coal spoil dumpsin Western Donbas the dominant species are Bromopsis inermis, subdominant Artemisia austriaca; widespread are also Festucas pp., Lathyrus tuberosus, Inula sp., Calamagrostis epigeios, Lotus ucrainicus, and Vicias pp. Identification of plants tolerant to target metals is a key issue in phytotechnology for soil restoration. It is hypothesized that naturally occurring plants growing on coal spoil dumps can be candidates for phytostabilization, phytoextraction (phytoaccumulation) and phytomining

  6. Neutronics Assessments for a RIA Fragmentation Line Beam Dump Concept

    CERN Document Server

    Boles, Jason; Reyes, Susana; Stein, Werner

    2005-01-01

    Heavy ion and radiation transport calculations are in progress for conceptual beam dump designs for the fragmentation line of the proposed Rare Isotope Accelerator (RIA). Using the computer code PHITS, a preliminary design of a motor-driven rotating wheel beam dump and adjacent downstream multipole has been modeled. Selected results of these calculations are given, including neutron and proton flux in the wheel, absorbed dose and displacements per atom in the hub materials, and heating from prompt radiation and from decay heat in the multipole.

  7. CFD Simulation of Flow Tones from Grazing Flow past a Deep Cavity

    International Nuclear Information System (INIS)

    T Bagwell

    2006-01-01

    Locked-in flow tones due to shear flow over a deep cavity are investigated using Large Eddy Simulation (LES). An isentropic form of the compressible Navier-Stokes equations (pseudo-compressibility) is used to couple the vertical flow over the cavity mouth with the deep cavity resonances (1). Comparisons to published experimental data (2) show that the pseudo-compressible LES formulation is capable of predicting the feedforward excitation of the deep cavity resonator, as well as the feedback process from the resonator to the flow source. By systematically increasing the resonator damping level, it is shown that strong lock-in results in a more organized shear layer than is observed for the locked-out flow state. By comparison, weak interactions (non-locked-in) produce no change in the shear layer characteristics. This supports the 40 dB definition of lock-in defined in the experiment

  8. The LHC superconducting cavities

    CERN Document Server

    Boussard, Daniel; Häbel, E; Kindermann, H P; Losito, R; Marque, S; Rödel, V; Stirbet, M

    1999-01-01

    The LHC RF system, which must handle high intensity (0.5 A d.c.) beams, makes use of superconducting single-cell cavities, best suited to minimizing the effects of periodic transient beam loading. There will be eight cavities per beam, each capable of delivering 2 MV (5 MV/m accelerating field) at 400 MHz. The cavities themselves are now being manufactured by industry, using niobium-on-copper technology which gives full satisfaction at LEP. A cavity unit includes a helium tank (4.5 K operating temperature) built around a cavity cell, RF and HOM couplers and a mechanical tuner, all housed in a modular cryostat. Four-unit modules are ultimately foreseen for the LHC (two per beam), while at present a prototype version with two complete units is being extensively tested. In addition to a detailed description of the cavity and its ancillary equipment, the first test results of the prototype will be reported.

  9. Pseudo-capacitor device for aqueous electrolytes

    Science.gov (United States)

    Prakash, Jai; Thackeray, Michael M.; Dees, Dennis W.; Vissers, Donald R.; Myles, Kevin M.

    1998-01-01

    A pseudo-capacitor having a high energy storage capacity develops a double layer capacitance as well as a Faradaic or battery-like redox reaction, also referred to as pseudo-capacitance. The Faradaic reaction gives rise to a capacitance much greater than that of the typical ruthenate oxide ultracapacitor which develops only charge separation-based double layer capacitance. The capacitor employs a lead and/or bismuth/ruthenate and/or iridium system having the formula A.sub.2 ›B.sub.2-x Pb.sub.x !O.sub.7-y, where A=Pb, Bi, and B=Ru, Ir, and Ocapacitor. The amount of expensive ruthenate and iridium can be substantially reduced in the pseudo-capacitor by increasing the lead content while improving energy storage capacity.

  10. Pseudo-entanglement evaluated in noninertial frames

    International Nuclear Information System (INIS)

    Mehri-Dehnavi, Hossein; Mirza, Behrouz; Mohammadzadeh, Hosein; Rahimi, Robabeh

    2011-01-01

    Research highlights: → We study pseudo-entanglement in noninertial frames. → We examine different measures of entanglement and nonclassical correlation for the state. → We find the threshold for entanglement is changed in noninertial frames. → We also describe the behavior of local unitary classes of states in noninertial frames. - Abstract: We study quantum discord, in addition to entanglement, of bipartite pseudo-entanglement in noninertial frames. It is shown that the entanglement degrades from its maximum value in a stationary frame to a minimum value in an infinite accelerating frame. There is a critical region found in which, for particular cases, entanglement of states vanishes for certain accelerations. The quantum discord of pseudo-entanglement decreases by increasing the acceleration. Also, for a physically inaccessible region, entanglement and nonclassical correlation are evaluated and shown to match the corresponding values of the physically accessible region for an infinite acceleration.

  11. SHiP: a new multipurpose beam-dump experiment at the SPS.

    CERN Document Server

    AUTHOR|(SzGeCERN)387671

    2016-01-01

    SHiP is an experiment to look for very weakly interacting particles at a new to be constructed beam-dum p facility at the CERN SPS. The SHiP Technical Proposal has been submitted to the CERN SPS Committee in April 2015. The 400 GeV/c proton beam extracted from the SPS will be dumped on a heavy target with the aim of integ rating $2\\times 10^{20}$ proton on target in five years. A detector located downstream of the target, based on a long vacuum tank followed by a spectrometer and particle identification detectors, will allow probing a variety of models with light long-lived exotic particles and masses below a few GeV/c$^2$. The main focus will be the physics of the so-called Hidden Portals, i.e. search for Dark Photons, Light scalars and pseudo-scalars, and Heavy Neutral Leptons (HNL). The sensitivity to HNL will allow for the first time to probe, in the mass range between the kaon and the charm meson mass, a coupling range for which Baryogenesis and active neutrino masses could also be explained...

  12. LEP copper accelerating cavities

    CERN Multimedia

    Laurent Guiraud

    1999-01-01

    These copper cavities were used to generate the radio frequency electric field that was used to accelerate electrons and positrons around the 27-km Large Electron-Positron (LEP) collider at CERN, which ran from 1989 to 2000. The copper cavities were gradually replaced from 1996 with new superconducting cavities allowing the collision energy to rise from 90 GeV to 200 GeV by mid-1999.

  13. Technogenic Rock Dumps Physical Properties' Prognosis via Results of the Structure Numerical Modeling

    Directory of Open Access Journals (Sweden)

    Markov Sergey

    2017-01-01

    Full Text Available Understanding of internal structure of the technogenic rock dumps (gob dumps is required condition for estimation of using ones as filtration massifs for treatment of mine wastewater. Internal structure of gob piles greatly depends on dumping technology to applying restrictions for use them as filtration massifs. Numerical modelling of gob dumps allows adequately estimate them physical parameters, as a filtration coefficient, density, etc. The gob dumps numerical modelling results given in this article, in particular was examined grain size distribution of determined fractions depend on dump height. Shown, that filtration coefficient is in a nonlinear dependence on amount of several fractions of rock in gob dump. The numerical model adequacy both the gob structure and the dependence of filtration coefficient from gob height acknowledged equality of calculated and real filtration coefficient values. The results of this research can be apply to peripheral dumping technology.

  14. The quality and quantity of runoff and groundwater in two overburden dumps undergoing pyritic oxidation

    International Nuclear Information System (INIS)

    Daniel, J.A.; Harries, J.R.; Ritchie, A.I.M.

    1983-01-01

    The quality and quantity of runoff and seepage water from two waste rock dumps at the abandoned uranium mine at Rum Jungle, N.T., have been monitored over various time intervals since 1975. Both dumps contain pyrite which is oxidising and solubilising trace metals within the dumps. Results are presented for the quality and quantity of runoff from both dumps measured in the 1980-81 wet season. The rainfall/runoff characteristics of the two dumps measured during this wet season are similar and in good agreement with measurements made in previous wet seasons. Pollution loads in runoff were only a few per cent of pollution loads in water percolating through to the base of the dumps. The rainfall/runoff characteristics and the dominance of pollution loads in water percolating through the dumps are likely to apply to other similar waste rock dumps

  15. Københavns Kommunes indsats mod social dumping - målopfyldelsesevaluering

    DEFF Research Database (Denmark)

    Baadsgaard, Kelvin; Jørgensen, Henning

    2016-01-01

    Evaluering af, om de politiske intentioner med indsats mod social dumping i Københavns Kommune er blevet indfriet......Evaluering af, om de politiske intentioner med indsats mod social dumping i Københavns Kommune er blevet indfriet...

  16. A case of Pseudo-Bartter syndrome

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Ik; Choi, Bo Whan; Lee, Yul; Chung, Soo Young [College of Medicine, Hallym University, Seoul (Korea, Republic of)

    1994-10-15

    Pseudo-Bartter Syndrome is a rare medical disease of the kidney characterized by normal blood pressure, hypokalemic metabolic alkalosis, hyperreninemia and hyperaldosteronism with drug history of diuretics. We report US, CT and MRI findings of a patients with clinically proved Pseudo-Bartter syndrome. The patient was a 37 year old woman with a history of long term ingestion of the diuretics(furosemide) for 20 years. Renal US revealed hyperechoic renal medulla at both kidneys. The resistive index(RI), calculated from the duplex doppler waveform is 0.61. Unenhanced CT revealed faint high attenuation along the medulla. T1-weighted MRI revealed indistinct corticomedullary differentiation.

  17. A case of Pseudo-Bartter syndrome

    International Nuclear Information System (INIS)

    Yang, Ik; Choi, Bo Whan; Lee, Yul; Chung, Soo Young

    1994-01-01

    Pseudo-Bartter Syndrome is a rare medical disease of the kidney characterized by normal blood pressure, hypokalemic metabolic alkalosis, hyperreninemia and hyperaldosteronism with drug history of diuretics. We report US, CT and MRI findings of a patients with clinically proved Pseudo-Bartter syndrome. The patient was a 37 year old woman with a history of long term ingestion of the diuretics(furosemide) for 20 years. Renal US revealed hyperechoic renal medulla at both kidneys. The resistive index(RI), calculated from the duplex doppler waveform is 0.61. Unenhanced CT revealed faint high attenuation along the medulla. T1-weighted MRI revealed indistinct corticomedullary differentiation

  18. Pseudo harmonic morphisms on Riemannian polyhedra

    International Nuclear Information System (INIS)

    Aprodu, M.A.; Bouziane, T.

    2004-10-01

    The aim of this paper is to extend the notion of pseudo harmonic morphism (introduced by Loubeau) to the case when the source manifold is an admissible Riemannian polyhedron. We define these maps to be harmonic in the sense of Eells-Fuglede and pseudo-horizontally weakly conformal in our sense. We characterize them by means of germs of harmonic functions on the source polyhedron, in the sense of Korevaar-Schoen, and germs of holomorphic functions on the Kaehler target manifold. (author)

  19. International Surveillance Mechanism for Sea Dumping of Radioactive Waste

    Science.gov (United States)

    OECD Observer, 1977

    1977-01-01

    The OECD consultation and surveillance mechanism is discussed in detail in this article. Four phases are identified and examined: (1) Notification, (2) Consultation, (3) Supervision, (4) Post-operation. This system is designed to provide the safest possible conditions for sea dumping of radioactive wastes. (MA)

  20. 7 CFR 58.212 - Hopper or dump room.

    Science.gov (United States)

    2010-01-01

    ....212 Hopper or dump room. A separate room shall be provided for the transfer of bulk dry dairy products to the hoppers and conveyors which lead to the fillers. This room shall meet the same requirements... transfer of dry dairy products from portable bulk bins will be accepted if gasketed surfaces or direct...

  1. Elasticity of substitution and anti-dumping decisions

    DEFF Research Database (Denmark)

    Hansen, Jørgen Drud; Meinen, Philipp; Nielsen, Jørgen Ulff-Møller

    2014-01-01

    Motivated by a monopolistic competition model with market segmentation and international price discrimination, this paper analyzes whether there is an inverse relation between the elasticity of substitution and final ad valorem anti-dumping duties across products. We test this for 19 countries...

  2. Bilge dump detection from SAR imagery using local binary patterns

    CSIR Research Space (South Africa)

    Mdakane, LW

    2015-07-01

    Full Text Available 2015: Remote Sensing: Understanding the Earth for a Safer World, Milan, Italy, 26-31 July 2015 Bilge dump detection from SAR imagery using local binary patterns yz L.W. Mdakane,yz W. Kleynhans,yz C.P. Schwegmann yDepartment of Electrical...

  3. Dumping of solid packaged radioactivity in the deep oceans

    International Nuclear Information System (INIS)

    Forster, Wm. O.; Van As, D.

    1980-01-01

    With the increasing use of nuclear energy, the quantity of radioactive wastes which are generated is also increasing. Their treatment and disposal is causing a concern in further development of nuclear energy. World's oceans are considered as a possible location for these wastes. A convention on the prevention of marine pollution caused by dumping of wastes and other matter into oceans was adopted at the Intergovernmental Conference held at London in November 1972. The convention prohibits dumping of high-level radioactive wastes in the oceans and has entrusted the IAEA the tasks of defining the high level radioactive wastes and providing recommendations for the issue of special permits for dumping of the radioactive materials which do not fall into the category of high-level wastes. A provisional definition and recommendations formulated by the IAEA and adopted by contractin.o. parties in 1976 are outlined. On the basis of an oceanographic model developed by Shepherd (1976) and considered to be the best available, a revised definition and revised recommendations were formulated. Their salient features are mentioned. The key parameters for specific site assessments are mentioned. The Nuclear Energy Agency also formulated guidelines on sea-disposal packages for radioactive wastes in 1974 and revised them in 1978. Finally it is noted that criteria have not been established for dumping of non-radioactive wastes in the ocean, though such criteria are contained in the IAEA recommendations in case of radioactive wastes. (M.G.B.)

  4. Results of evaluation of tailing dumps dust intensity

    Directory of Open Access Journals (Sweden)

    Masloboev V. A.

    2016-03-01

    Full Text Available A set of most acceptable and well-known methods of dust intensity evaluation has been defined and tested (dependence of Westphal D. L. et al. and DEAD scheme based on the analysis of exiting approaches (deserts, tailing dumps, etc.. The description of the chosen methods has been given. The determination of dynamic velocity u* and velocity at the height of +10 m above the dusting surface u10 which are necessary to evaluate the dust intensity has been demonstrated. The method is based on two-dimensional numerical model of atmosphere aerodynamics in the area of "tailing dumps of ANOF-2 ‒ the town of Apatity". The study provides calculations of horizontal velocity at the height of +10 m above the dusting surface at the wind speed varying from 5 to 23 m/sec. The work also suggests the results of graphical data processing related to tailing grain size distribution from the surface of the firmly established surface of the tailing dumps of ANOF-2. Comparative analysis has been given and the peculiarities of interval (based on grains sizes dust intensity of the tailing dumps of ANOF-2 have been shown using the dependence of Westphal D. L. et al. and DEAD scheme within the wind speed range. The received values of dust intensity at the lower range limit are close to the "maximum specific dust off" value which is used by project specialists for documentation development

  5. Extraction of Gold from Dump Material by Agitation | Stoyanov ...

    African Journals Online (AJOL)

    As a result of poor extraction of gold from slimes a new approach-mechanical agitation of dump material was explored. Several tests have been done. In the agitation test work the following parameters have been investigated: impeller speed; cyanide concentration; CaO concentration; liquid-solid ratio; lead nitrate dosage ...

  6. Solid waste dumping site suitability analysis using geographic ...

    African Journals Online (AJOL)

    Solid waste dumping site suitability analysis using geographic information system (GIS) and remote sensing for Bahir Dar Town, North Western Ethiopia. ... The PDF file you selected should load here if your Web browser has a PDF reader plug-in installed (for example, a recent version of Adobe Acrobat Reader).

  7. Effects on the environment of the dumping of nuclear wastes

    International Nuclear Information System (INIS)

    1990-07-01

    Nationally and internationally accepted procedures and technologies are available for the safe handling and disposal of radioactive wastes. Authorized waste disposal practices are designed to ensure that there will be no significant impacts on man and his environment. 'Dumping' of nuclear wastes may result in the elimination of one or more of the multibarriers of protection inherent in an effective radioactive waste management system, thereby increasing the risk of radiological exposure to man and his environment. Quantitative assessments of the degree of environmental contamination and of the resulting hazards to man depend on the specific conditions surrounding the 'uncontrolled disposal' of radioactive waste. These include the nature and activity level of the waste, the physical form of the waste, the package that the waste is contained in and the characteristics of the dumping site. Depending on the scenario envisaged, the consequences of 'uncontrolled disposal' could vary from being insignificant to a situation where there is a significant hazard to an exposed population group. International transactions involving nuclear wastes are taking place between countries on the basis of bilateral agreements and under strict regulatory supervision so that radioactive wastes are transferred safely from one controlled area to another. Such transactions may increase in the future with increased international co-operation in sharing common waste repositories. No evidence exists that confirms that transboundary dumping of radioactive waste has occurred. Investigation of alleged dumping of radioactive wastes by the International Atomic Energy Agency has revealed that the 'suspect wastes' did not contain radioactive material. 2 tabs

  8. Beam Dump Design for the Rare Isotope Accelerator Fragmentation Line

    Energy Technology Data Exchange (ETDEWEB)

    Stein, W; Ahle, L E; Reyes, S

    2006-05-02

    Beam dumps for the heavy ion beams of the fragmentation line of the Rare Isotope Accelerator have been designed. The most severe operational case involves a continuous U beam impacting the beam dump with a power of 295 kW and a nominal spot diameter size of 5 cm. The dump mechanically consists of two rotating barrels with a water cooled outer wall of 2 mm thick aluminum. The barrels are 70 cm in diameter and axially long enough to intercept a variety of other beams. The aluminum wall absorbs approximately 15% of the U beam power with the rest absorbed in the water downstream of the wall. The water acts as an absorber of the beam and as a coolant for the 2 mm aluminum wall. The barrel rotates at less than 400 RPM, maximum aluminum temperatures are less than 100 C and maximum thermal fatigue stresses are low at 3.5 x 10{sup 7} Pa (5 ksi). Rotation of the dump results in relatively low radiation damage levels with an operating lifetime of years for most beams.

  9. ALPtraum. ALP production in proton beam dump experiments

    International Nuclear Information System (INIS)

    Doebrich, Babette; Jaeckel, Joerg

    2015-12-01

    With their high beam energy and intensity, existing and near-future proton beam dumps provide an excellent opportunity to search for new very weakly coupled particles in the MeV to GeV mass range. One particularly interesting example is a so-called axion-like particle (ALP), i.e. a pseudoscalar coupled to two photons. The challenge in proton beam dumps is to reliably calculate the production of the new particles from the interactions of two composite objects, the proton and the target atoms. In this work we argue that Primakoff production of ALPs proceeds in a momentum range where production rates and angular distributions can be determined to sufficient precision using simple electromagnetic form factors. Reanalysing past proton beam dump experiments for this production channel, we derive novel constraints on the parameter space for ALPs. We show that the NA62 experiment at CERN could probe unexplored parameter space by running in 'dump mode' for a few days and discuss opportunities for future experiments such as SHiP.

  10. Leachate characterization of active and closed dump sites in Port ...

    African Journals Online (AJOL)

    This study characterizes the leachate quality of both active and closed dump sites in Port Harcourt City. Leachates were sampled from the base of the dum psites and analysed, pH, dissolved oxygen (DO), electrical conductivity and total dissolved solids were determined on the samples in-situ. While chloride, sulphate ...

  11. Acid Mine Drainage Potential of the Coral Snake Waste Dump ...

    African Journals Online (AJOL)

    This paper assessed the Acid Mine Drainage (AMD) potential of the Coral Snake Waste Dump located close to the Enkansu and Kaw streams in Obuasi. Ten water and fifty rock samples were analysed for physico-chemical parameters. Acid Base Accounting (ABA) determinations using static methods were employed to ...

  12. Particulate Matter and Noise Impact Studies of Waste Rock Dump ...

    African Journals Online (AJOL)

    Adansi Gold Company Limited identified an economically viable gold deposit at Nkran in the Amansie West District of Ghana. Mining of this deposit requires the disposal of waste rock materials at a proposed waste rock dump near Nkran and Koninase communities. Since particulates and noise emissions from the ...

  13. Direct-heating solar-collector dump valve

    Science.gov (United States)

    Howikman, T. C.

    1977-01-01

    Five-port ganged valve isolates collector from primary load system pressure and drains collectors, allowing use of direct heating with all its advantages. Valve is opened and closed by same switch that controls pump or by temperature sensor set at O C, while providing direct dump option.

  14. Research Note Impacts of mine dump pollution on plant species ...

    African Journals Online (AJOL)

    Effects of mine dump pollution on semiarid savanna vegetation were investigated in Kombat, Namibia. Vegetation structure, species richness, composition and diversity were compared between polluted and control sites. Concentrations of arsenic, chromium, copper, lead and zinc in soils were significantly higher closer to a ...

  15. Refuse Dumps And The Environment: A Case Study Of Some ...

    African Journals Online (AJOL)

    Refuse Dumps And The Environment: A Case Study Of Some Selected Cities In Nigeria. ... International Journal of Emotional Psychology and Sport Ethics ... This study assessed the level of environmental pollution in the nation by focusing on the degree of accumulation of house – hold wastes, industrial scraps or wastes, ...

  16. Bounds on light gluinos from the BEBC beam dump experiments

    International Nuclear Information System (INIS)

    Cooper-Sarkar, A.M.; Parker, M.A.; Sarkar, S.; Klein, H.; Morrison, D.R.O.; Schmid, P.; Wachsmuth, H.; Aderholz, M.; Schmitz, N.; Bostock, P.; Krstic, J.; Faccini-Turluer, M.L.; Vignaud, D.; Graessler, H.; Guy, J.; Venus, W.; Hulth, P.O.; Hultqvist, K.; Walck, C.; Idschok, U.; Kreutzmann, H.; Nellen, B.; Wuensch, B.

    1985-01-01

    Observational upper limits on anomalous neutral-current events in a proton beam dump experiment are used to constrain the possible hadroproduction and decay of light gluinos. These results require msub(g tilde) >= 4 GeV for Msub(q tilde) approx.= msub(w). (orig.)

  17. Bounds on light gluinos from the BEBC beam dump experiment

    Science.gov (United States)

    Cooper-Sarkar, A. M.; Parker, M. A.; Sarkar, S.; Aderholz, M.; Bostock, P.; Clayton, E. F.; Faccini-Turluer, M. L.; Grässler, H.; Guy, J.; Hulth, P. O.; Hultqvist, K.; Idschok, U.; Klein, H.; Kreutzmann, H.; Krstic, J.; Mobayyen, M. M.; Morrison, D. R. O.; Nellen, B.; Schmid, P.; Schmitz, N.; Talebzadeh, M.; Venus, W.; Vignaud, D.; Walck, Ch.; Wachsmuth, H.; Wünsch, B.; WA66 Collaboration

    1985-10-01

    Observational upper limits on anomalous neutral-current events in a proton beam dump experiment are used to constrain the possible hadroproduction and decay of light gluinos. These results require ifm g˜$̆4 GeV for ifm q˜ - minw.

  18. Pioneer vegetation on ash dumps in Oswiecim (southern Poland)

    Energy Technology Data Exchange (ETDEWEB)

    Bojarczuk, T.; Kuczynski, B.

    1972-01-01

    The authors found fifty-three plant species growing on the ash dumps in Oswiecim, while in 1963 twenty-two species only were encountered there. Most of the self-sown plants belong to calciphilous, ruderal and xerophilous species. The pH of the ashes amounts to 9.5. Some of them, e.g. Matricaria chamomilla are index plants for acid habitats; others were hitherto encountered in wet habitats, e.g. Rumex obtusifolias, Myricaria germanica, Epilobium roseum, and others. Their occurrence on ash dumps is possible thanks to the considerable amount of precipitation (465 mm) during the vegetative period. The mosses are the pioneers of these dumps, e.g. Funaria hygromertrica and Bryum argenteum, which usually appear on the site of fire. The authors are of the opinion that a better knowledge of the plants appearing spontaneously on dumps and waste heaps may provide many useful conclusions which will help to obtain positive results at the recultivation of spoil heaps and industrial wastes. 9 references, 3 tables.

  19. 7 CFR 58.228 - Dump hoppers, screens, mixers and conveyors.

    Science.gov (United States)

    2010-01-01

    ... Service 1 Equipment and Utensils § 58.228 Dump hoppers, screens, mixers and conveyors. The product contact surfaces of dump hoppers, screens, mixers and conveyors which are used in the process of transferring dry... 7 Agriculture 3 2010-01-01 2010-01-01 false Dump hoppers, screens, mixers and conveyors. 58.228...

  20. Determination of heavy metals in soils from dump site of tanneries ...

    African Journals Online (AJOL)

    Heavy metals were determined in soil samples at the dump site, Challawa town, Karfi Irrigation site and farmlands near the dump site by flame Atomic Absorption Spectrophotometer (AAS). The results showed that soil at the dump site contains significant amount of toxic elements. Hence remediation processes were ...

  1. Anthropogenic Pollutants in Extracts from Maritsa Iztok Dumps

    Science.gov (United States)

    Stefanova, Maya; Milakovska, Zlatka; Marinov, Stefan

    2017-12-01

    Coals are suspected for many human health problems and are an object of the new discipline - “medical geology”. Potential human health risk of organic compounds with coal/lignite provenance includes endocrine disruption, nephrotoxicity, cancer, etc. Recent investigations proved that different organic components, i.e. hydrocarbons, phenols etc. move through/release out of the dump area as a result of alteration processes of the organic matter (OM) caused by the wash-out and/or drainage processes. The timeliness of the present study is based on the scarcity of information on organic geochemistry of dump materials from open pit coal mines and weathered lignites in particular. The limited number of studies on dumps clarifies that even for the “short” time span (some tens of years) in geological point of view, processes of transformation of the extractable OM are detectable. The secondary phases, a result of the OM transformations, move through and out of the dump area and could be potential contaminants for the surface/underground waters and soils in the area. Another environmental problem comes from the air-born VOCs and products of the modern chemical industry. By GC-MS in the slightly polar fractions of the chloroform extracts of dump samples a broad set of components was determined, i.e. phthalates (dominant), i-propyl palmitate, i-propyl myristate, n-hexyl benzoates, etc. These organic contaminants could be regarded more likely as anthropogenic (originating from plasticizers, industrial pollutants, etc.). Presently, it seems that the identified compounds do not represent an acute toxic risk from an environmental viewpoint. However, some compounds could raise concerns and further attention is needed to be focused on them.

  2. Pseudo-observations in survival analysis

    DEFF Research Database (Denmark)

    Andersen, Per Kragh; Perme, Maja Pohar

    2010-01-01

    -state models, e.g. the competing risks cumulative incidence function. Graphical and numerical methods for assessing goodness-of-fit for hazard regression models and for the Fine-Gray model in competing risks studies based on pseudo-observations are also reviewed. Sensitivity to covariate-dependent censoring...

  3. Leonardo and the Pseudo-RCO

    OpenAIRE

    Wills, Joerg M.

    2013-01-01

    There are two hypotheses on Leonardo's polyhedron based on the Pseudo-RCO and drawn for Luca Pacioli's book: Leonardo made an error, or: Leonardo draw it with intention, as it is. We give arguments, which support the Intention-hypothesis.

  4. Genetics Home Reference: intestinal pseudo-obstruction

    Science.gov (United States)

    ... A characteristic of X-linked inheritance is that fathers cannot pass X-linked traits to their sons. Intestinal pseudo-obstruction caused by ACTG2 gene mutations is inherited in an autosomal dominant pattern , which means one copy of the altered ...

  5. Pseudo--Normals for Signed Distance Computation

    DEFF Research Database (Denmark)

    Aanæs, Henrik; Bærentzen, Jakob Andreas

    2003-01-01

    the relation of a point to a mesh. At the vertices and edges of a triangle mesh, the surface is not \\$C\\^1\\$ continuous. Hence, the normal is undefined at these loci. Thürmer and Wüthrich proposed the \\$\\backslash\\$emph{angle weighted pseudo--normal} as a way to deal with this problem. In this paper, we...

  6. On holography for (pseudo-)conformal cosmology

    Energy Technology Data Exchange (ETDEWEB)

    Libanov, M. [Institute for Nuclear Research of the Russian Academy of Sciences, 60th October Anniversary Prospect, 7a, 117312, Moscow (Russian Federation); Moscow Institute of Physics and Technology, Institutskii per., 9, 141700, Dolgoprudny, Moscow Region (Russian Federation); Rubakov, V. [Institute for Nuclear Research of the Russian Academy of Sciences, 60th October Anniversary Prospect, 7a, 117312, Moscow (Russian Federation); Department of Particle Physics and Cosmology, Physics Faculty, Moscow State University, Vorobjevy Gory, 119991, Moscow (Russian Federation); Sibiryakov, S., E-mail: sibir@ms2.inr.ac.ru [Institute for Nuclear Research of the Russian Academy of Sciences, 60th October Anniversary Prospect, 7a, 117312, Moscow (Russian Federation); Theory Group, Physics Department, CERN, CH-1211 Geneva 23 (Switzerland); FSB/ITP/LPPC, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland)

    2015-02-04

    We propose a holographic dual for (pseudo-)conformal cosmological scenario, with a scalar field that forms a moving domain wall in adS{sub 5}. The domain wall separates two vacua with unequal energy densities. Unlike in the existing construction, the 5d solution is regular in the relevant space–time domain.

  7. On holography for (pseudo-)conformal cosmology

    CERN Document Server

    Libanov, M.; Sibiryakov, S.

    2015-01-01

    We propose a holographic dual for (pseudo-)conformal cosmological scenario, with a scalar field that forms a moving domain wall in adS_5. The domain wall separates two vacua with unequal energy densities. Unlike in the existing construction, the 5d solution is regular in the relevant space-time domain.

  8. Cavity design programs

    International Nuclear Information System (INIS)

    Nelson, E.M.

    1996-01-01

    Numerous computer programs are available to help accelerator physicists and engineers model and design accelerator cavities and other microwave components. This article discusses the problems these programs solve and the principles upon which these programs are based. Some examples of how these programs are used in the design of accelerator cavities are also given

  9. Cavity quantum electrodynamics

    International Nuclear Information System (INIS)

    Walther, Herbert; Varcoe, Benjamin T H; Englert, Berthold-Georg; Becker, Thomas

    2006-01-01

    This paper reviews the work on cavity quantum electrodynamics of free atoms. In recent years, cavity experiments have also been conducted on a variety of solid-state systems resulting in many interesting applications, of which microlasers, photon bandgap structures and quantum dot structures in cavities are outstanding examples. Although these phenomena and systems are very interesting, discussion is limited here to free atoms and mostly single atoms because these systems exhibit clean quantum phenomena and are not disturbed by a variety of other effects. At the centre of our review is the work on the one-atom maser, but we also give a survey of the entire field, using free atoms in order to show the large variety of problems dealt with. The cavity interaction can be separated into two main regimes: the weak coupling in cavity or cavity-like structures with low quality factors Q and the strong coupling when high-Q cavities are involved. The weak coupling leads to modification of spontaneous transitions and level shifts, whereas the strong coupling enables one to observe a periodic exchange of photons between atoms and the radiation field. In this case, atoms and photons are entangled, this being the basis for a variety of phenomena observed, some of them leading to interesting applications in quantum information processing. The cavity experiments with free atoms reached a new domain with the advent of experiments in the visible spectral region. A review on recent achievements in this area is also given

  10. Formation of coronal cavities

    International Nuclear Information System (INIS)

    An, C.H.; Suess, S.T.; Tandberg-Hanssen, E.; Steinolfson, R.S.

    1986-01-01

    A theoretical study of the formation of a coronal cavity and its relation to a quiescent prominence is presented. It is argued that the formation of a cavity is initiated by the condensation of plasma which is trapped by the coronal magnetic field in a closed streamer and which then flows down to the chromosphere along the field lines due to lack of stable magnetic support against gravity. The existence of a coronal cavity depends on the coronal magnetic field strength; with low strength, the plasma density is not high enough for condensation to occur. Furthermore, we suggest that prominence and cavity material is supplied from the chromospheric level. Whether a coronal cavity and a prominence coexist depends on the magnetic field configuration; a prominence requires stable magnetic support

  11. Sea-dumped chemical weapons: environmental risk, occupational hazard.

    Science.gov (United States)

    Greenberg, M I; Sexton, K J; Vearrier, D

    2016-01-01

    Chemical weapons dumped into the ocean for disposal in the twentieth century pose a continuing environmental and human health risk. In this review we discuss locations, quantity, and types of sea-dumped chemical weapons, related environmental concerns, and human encounters with sea-dumped chemical weapons. We utilized the Ovid (http://ovidsp.tx.ovid.com) and PubMed (http://www.pubmed.org) search engines to perform MEDLINE searches for the terms 'sea-dumped chemical weapons', 'chemical warfare agents', and 'chemical munitions'. The searches returned 5863 articles. Irrelevant and non-English articles were excluded. A review of the references for these articles yielded additional relevant sources, with a total of 64 peer-reviewed articles cited in this paper. History and geography of chemical weapons dumping at sea: Hundreds of thousands of tons of chemical munitions were disposed off at sea following World War II. European, Russian, Japanese, and United States coasts are the areas most affected worldwide. Several areas in the Baltic and North Seas suffered concentrated large levels of dumping, and these appear to be the world's most studied chemical warfare agent marine dumping areas. Chemical warfare agents: Sulfur mustard, Lewisite, and the nerve agents appear to be the chemical warfare agents most frequently disposed off at sea. Multiple other type of agents including organoarsenicals, blood agents, choking agents, and lacrimators were dumped at sea, although in lesser volumes. Environmental concerns: Numerous geohydrologic variables contribute to the rate of release of chemical agents from their original casings, leading to difficult and inexact modeling of risk of release into seawater. Sulfur mustard and the organoarsenicals are the most environmentally persistent dumped chemical agents. Sulfur mustard in particular has a propensity to form a solid or semi-solid lump with a polymer coating of breakdown products, and can persist in this state on the ocean floor

  12. Database Dump - fRNAdb | LSDB Archive [Life Science Database Archive metadata

    Lifescience Database Archive (English)

    Full Text Available List Contact us fRNAdb Database Dump Data detail Data name Database Dump DOI 10.18908/lsdba.nbdc00452-002 De... data (tab separeted text) Data file File name: Database_Dump File URL: ftp://ftp....biosciencedbc.jp/archive/frnadb/LATEST/Database_Dump File size: 673 MB Simple search URL - Data acquisition...s. Data analysis method - Number of data entries 4 files - About This Database Database Description Download... License Update History of This Database Site Policy | Contact Us Database Dump - fRNAdb | LSDB Archive ...

  13. Primary palpebral and orbital ossification in pseudo-pseudohypoparathyroidism

    DEFF Research Database (Denmark)

    Klauber, S.; Heegaard, S.; Prause, J.U.

    2002-01-01

    ophthalmology, Albright's heriditary osteodystrophy, ossification, pseudo-pseudohypoparathyroidism, pseodohypoparathyroidism, hypothyroidism, GNAS1 gene, history, eyelid, orbit......ophthalmology, Albright's heriditary osteodystrophy, ossification, pseudo-pseudohypoparathyroidism, pseodohypoparathyroidism, hypothyroidism, GNAS1 gene, history, eyelid, orbit...

  14. SPS RF Accelerating Cavity

    CERN Multimedia

    1979-01-01

    This picture shows one of the 2 new cavities installed in 1978-1979. The main RF-system of the SPS comprises four cavities: two of 20 m length and two of 16.5 m length. They are all installed in one long straight section (LSS 3). These cavities are of the travelling-wave type operating at a centre frequency of 200.2 MHz. They are wideband, filling time about 700 ns and untuned. The power amplifiers, using tetrodes are installed in a surface building 200 m from the cavities. Initially only two cavities were installed, a third cavity was installed in 1978 and a forth one in 1979. The number of power amplifiers was also increased: to the first 2 MW plant a second 2 MW plant was added and by end 1979 there were 8 500 kW units combined in pairs to feed each of the 4 cavities with up to about 1 MW RF power, resulting in a total accelerating voltage of about 8 MV. See also 7412016X, 7412017X, 7411048X

  15. Superconducting TESLA cavities

    Directory of Open Access Journals (Sweden)

    B. Aune

    2000-09-01

    Full Text Available The conceptional design of the proposed linear electron-positron collider TESLA is based on 9-cell 1.3 GHz superconducting niobium cavities with an accelerating gradient of E_{acc}≥25 MV/m at a quality factor Q_{0}≥5×10^{9}. The design goal for the cavities of the TESLA Test Facility (TTF linac was set to the more moderate value of E_{acc}≥15 MV/m. In a first series of 27 industrially produced TTF cavities the average gradient at Q_{0}=5×10^{9} was measured to be 20.1±6.2 MV/m, excluding a few cavities suffering from serious fabrication or material defects. In the second production of 24 TTF cavities, additional quality control measures were introduced, in particular, an eddy-current scan to eliminate niobium sheets with foreign material inclusions and stringent prescriptions for carrying out the electron-beam welds. The average gradient of these cavities at Q_{0}=5×10^{9} amounts to 25.0±3.2 MV/m with the exception of one cavity suffering from a weld defect. Hence only a moderate improvement in production and preparation techniques will be needed to meet the ambitious TESLA goal with an adequate safety margin. In this paper we present a detailed description of the design, fabrication, and preparation of the TESLA Test Facility cavities and their associated components and report on cavity performance in test cryostats and with electron beam in the TTF linac. The ongoing research and development towards higher gradients is briefly addressed.

  16. Cavity-enhanced spectroscopies

    CERN Document Server

    van Zee, Roger

    2003-01-01

    ""Cavity-Enhanced Spectroscopy"" discusses the use of optical resonators and lasers to make sensitive spectroscopic measurements. This volume is written by the researcchers who pioneered these methods. The book reviews both the theory and practice behind these spectroscopic tools and discusses the scientific discoveries uncovered by these techniques. It begins with a chapter on the use of optical resonators for frequency stabilization of lasers, which is followed by in-depth chapters discussing cavity ring-down spectroscopy, frequency-modulated, cavity-enhanced spectroscopy, intracavity spectr

  17. Tuned optical cavity magnetometer

    Science.gov (United States)

    Okandan, Murat; Schwindt, Peter

    2010-11-02

    An atomic magnetometer is disclosed which utilizes an optical cavity formed from a grating and a mirror, with a vapor cell containing an alkali metal vapor located inside the optical cavity. Lasers are used to magnetically polarize the alkali metal vapor and to probe the vapor and generate a diffracted laser beam which can be used to sense a magnetic field. Electrostatic actuators can be used in the magnetometer for positioning of the mirror, or for modulation thereof. Another optical cavity can also be formed from the mirror and a second grating for sensing, adjusting, or stabilizing the position of the mirror.

  18. Hydroforming of elliptical cavities

    Science.gov (United States)

    Singer, W.; Singer, X.; Jelezov, I.; Kneisel, P.

    2015-02-01

    Activities of the past several years in developing the technique of forming seamless (weldless) cavity cells by hydroforming are summarized. An overview of the technique developed at DESY for the fabrication of single cells and multicells of the TESLA cavity shape is given and the major rf results are presented. The forming is performed by expanding a seamless tube with internal water pressure while simultaneously swaging it axially. Prior to the expansion the tube is necked at the iris area and at the ends. Tube radii and axial displacements are computer controlled during the forming process in accordance with results of finite element method simulations for necking and expansion using the experimentally obtained strain-stress relationship of tube material. In cooperation with industry different methods of niobium seamless tube production have been explored. The most appropriate and successful method is a combination of spinning or deep drawing with flow forming. Several single-cell niobium cavities of the 1.3 GHz TESLA shape were produced by hydroforming. They reached accelerating gradients Eacc up to 35 MV /m after buffered chemical polishing (BCP) and up to 42 MV /m after electropolishing (EP). More recent work concentrated on fabrication and testing of multicell and nine-cell cavities. Several seamless two- and three-cell units were explored. Accelerating gradients Eacc of 30 - 35 MV /m were measured after BCP and Eacc up to 40 MV /m were reached after EP. Nine-cell niobium cavities combining three three-cell units were completed at the company E. Zanon. These cavities reached accelerating gradients of Eacc=30 - 35 MV /m . One cavity is successfully integrated in an XFEL cryomodule and is used in the operation of the FLASH linear accelerator at DESY. Additionally the fabrication of bimetallic single-cell and multicell NbCu cavities by hydroforming was successfully developed. Several NbCu clad single-cell and double-cell cavities of the TESLA shape have been

  19. Hydroforming of elliptical cavities

    Directory of Open Access Journals (Sweden)

    W. Singer

    2015-02-01

    Full Text Available Activities of the past several years in developing the technique of forming seamless (weldless cavity cells by hydroforming are summarized. An overview of the technique developed at DESY for the fabrication of single cells and multicells of the TESLA cavity shape is given and the major rf results are presented. The forming is performed by expanding a seamless tube with internal water pressure while simultaneously swaging it axially. Prior to the expansion the tube is necked at the iris area and at the ends. Tube radii and axial displacements are computer controlled during the forming process in accordance with results of finite element method simulations for necking and expansion using the experimentally obtained strain-stress relationship of tube material. In cooperation with industry different methods of niobium seamless tube production have been explored. The most appropriate and successful method is a combination of spinning or deep drawing with flow forming. Several single-cell niobium cavities of the 1.3 GHz TESLA shape were produced by hydroforming. They reached accelerating gradients E_{acc} up to 35  MV/m after buffered chemical polishing (BCP and up to 42  MV/m after electropolishing (EP. More recent work concentrated on fabrication and testing of multicell and nine-cell cavities. Several seamless two- and three-cell units were explored. Accelerating gradients E_{acc} of 30–35  MV/m were measured after BCP and E_{acc} up to 40  MV/m were reached after EP. Nine-cell niobium cavities combining three three-cell units were completed at the company E. Zanon. These cavities reached accelerating gradients of E_{acc}=30–35  MV/m. One cavity is successfully integrated in an XFEL cryomodule and is used in the operation of the FLASH linear accelerator at DESY. Additionally the fabrication of bimetallic single-cell and multicell NbCu cavities by hydroforming was successfully developed. Several NbCu clad single-cell and

  20. Wavefield extrapolation in pseudo-depth domain

    KAUST Repository

    Ma, Xuxin; Alkhalifah, Tariq Ali

    2012-01-01

    Extrapolating seismic waves in Cartesian coordinate is prone to uneven spatial sampling, because the seismic wavelength tends to grow with depth, as velocity increase. We transform the vertical depth axis to a pseudo one using a velocity weighted mapping, which can effectively mitigate this wavelength variation. We derive acoustic wave equations in this new domain based on the direct transformation of the Laplacian derivatives, which admits solutions that are more accurate and stable than those derived from the kinematic transformation. The anisotropic versions of these equations allow us to isolate the vertical velocity influence and reduce its impact on modeling and imaging. The major benefit of extrapolating wavefields in pseudo-depth space is its near uniform wavelength as opposed to the normally dramatic change of wavelength with the conventional approach. Time wavefield extrapolation on a complex velocity shows some of the features of this approach.

  1. [Hysterical pseudo-coma: A case report].

    Science.gov (United States)

    Chouaib, N; Chouaib, H; Belyamani, L; Otheman, Y; Bichra, M Z

    2015-09-01

    Hysterical pseudo-coma corresponds to a state of clinical sleep with contrasting waking electroencephalogram. It can last several hours or even several days in the absence of an underlying organic disease. In psychiatry, this disorder is currently part of the "dissociative disorder not otherwise specified". Through this case report, we describe the evolution of a hysterical pseudo-coma that lasted four days in a 28-year-old man. The normality of biological, radiological and electroencephalographic assessments, and responsiveness of the patient during the implementation of a nasogastric tube, led us to suspect a mental origin. An adapted psychiatric care allowed the patient to recover his autonomy after three days of hospitalization. This had prevented the escalation of explorations and invasive treatments. However, the search for organic comorbidity and its management remains a priority. Copyright © 2014 L’Encéphale, Paris. Published by Elsevier Masson SAS. All rights reserved.

  2. Pseudo-Goldstino in Field Theory

    International Nuclear Information System (INIS)

    Argurio, Riccardo; Komargodski, Zohar; Mariotti, Alberto

    2011-01-01

    We consider two SUSY-breaking hidden sectors which decouple when their respective couplings to the visible particles are switched off. In such a scenario one expects to find two light fermions: the Goldstino and the pseudo-Goldstino. While the former remains massless in the rigid limit, the latter becomes massive due to radiative effects which we analyze from several different points of view. This analysis is greatly facilitated by a version of the Goldberger-Treiman relation, which allows us to write a universal nonperturbative formula for the mass. We carry out the analysis in detail in the context of gauge mediation, where we find that the pseudo-Goldstino mass is at least around the GeV scale and can be easily at the electroweak range, even in low scale models. This leads to interesting and unconventional possibilities in collider physics and it also has potential applications in cosmology.

  3. 3D Object Metamorphosis with Pseudo Metameshes

    Directory of Open Access Journals (Sweden)

    MOCANU, B.

    2015-02-01

    Full Text Available In this paper we introduce a novel framework for 3D object metamorphosis, represented by closed triangular meshes. The systems returns a high quality transition sequence, smooth and gradual, that is visual pleasant and consistent to both source and target topologies. The method starts by parameterizing both the source and the target model to a common domain (the unit sphere. Then, the features selected from the two models are aligned by applying the CTPS C2a radial basis functions. We demonstrate how the selected approach can create valid warping by deforming the models embedded into the parametric domain. In the final stage, we propose and validate a novel algorithm to construct a pseudo-supermesh able to approximate both, the source and target 3D objects. By using the pseudo-supermesh we developed a morphing transition consistent with respect to both geometry and topology of the 3D models.

  4. Pseudo-differential operators and generalized functions

    CERN Document Server

    Toft, Joachim

    2015-01-01

    This book gathers peer-reviewed contributions representing modern trends in the theory of generalized functions and pseudo-differential operators. It is dedicated to Professor Michael Oberguggenberger (Innsbruck University, Austria) in honour of his 60th birthday. The topics covered were suggested by the ISAAC Group in Generalized Functions (GF) and the ISAAC Group in Pseudo-Differential Operators (IGPDO), which met at the 9th ISAAC congress in Krakow, Poland in August 2013. Topics include Columbeau algebras, ultra-distributions, partial differential equations, micro-local analysis, harmonic analysis, global analysis, geometry, quantization, mathematical physics, and time-frequency analysis. Featuring both essays and research articles, the book will be of great interest to graduate students and researchers working in analysis, PDE and mathematical physics, while also offering a valuable complement to the volumes on this topic previously published in the OT series.

  5. Pseudo ribbon metal ion beam source

    International Nuclear Information System (INIS)

    Stepanov, Igor B.; Ryabchikov, Alexander I.; Sivin, Denis O.; Verigin, Dan A.

    2014-01-01

    The paper describes high broad metal ion source based on dc macroparticle filtered vacuum arc plasma generation with the dc ion-beam extraction. The possibility of formation of pseudo ribbon beam of metal ions with the parameters: ion beam length 0.6 m, ion current up to 0.2 A, accelerating voltage 40 kV, and ion energy up to 160 kV has been demonstrated. The pseudo ribbon ion beam is formed from dc vacuum arc plasma. The results of investigation of the vacuum arc evaporator ion-emission properties are presented. The influence of magnetic field strength near the cathode surface on the arc spot movement and ion-emission properties of vacuum-arc discharge for different cathode materials are determined. It was shown that vacuum-arc discharge stability can be reached when the magnetic field strength ranges from 40 to 70 G on the cathode surface

  6. Pseudo ribbon metal ion beam source.

    Science.gov (United States)

    Stepanov, Igor B; Ryabchikov, Alexander I; Sivin, Denis O; Verigin, Dan A

    2014-02-01

    The paper describes high broad metal ion source based on dc macroparticle filtered vacuum arc plasma generation with the dc ion-beam extraction. The possibility of formation of pseudo ribbon beam of metal ions with the parameters: ion beam length 0.6 m, ion current up to 0.2 A, accelerating voltage 40 kV, and ion energy up to 160 kV has been demonstrated. The pseudo ribbon ion beam is formed from dc vacuum arc plasma. The results of investigation of the vacuum arc evaporator ion-emission properties are presented. The influence of magnetic field strength near the cathode surface on the arc spot movement and ion-emission properties of vacuum-arc discharge for different cathode materials are determined. It was shown that vacuum-arc discharge stability can be reached when the magnetic field strength ranges from 40 to 70 G on the cathode surface.

  7. Marine reactor pressure vessels dumped in the Kara Sea

    International Nuclear Information System (INIS)

    Mount, M.E.

    1997-01-01

    Between 1965 and 1988, 16 marine reactors from seven Russian submarines and the icebreaker Lenin, each of which suffered some form of reactor accident, were dumped in a variety of containments, using a number of sealing methods, at five sites in the Kara Sea. All reactors were dumped at sites that varied in depth from 12 to 300 m and six contained their spent nuclear fuel (SNF). This paper examines the breakdown of the reactor pressure vessel (RPV) barriers due to corrosion, with specific emphasis on those RPVs containing SNF. Included are discussions of the structural aspects of the steam generating installations and their associated RPVs, a summary of the disposal operations, assumptions on corrosion rates of structural and filler materials, and an estimate of the structural integrity of the RPVs at the present time (1996) and in the year 2015

  8. Radiological aspects of sea bed dumping in the deep oceans

    International Nuclear Information System (INIS)

    Templeton, W.L.

    1979-01-01

    In order to control coastal discharges or ocean dumping of any kind of material, it is necessary to determine a release rate. This can only come from a knowledge of the composition and chemical form of the source materials, the distribution and bioavailability of these materials in the ocean ecosystem, the degree and rates of bioaccumulation and the actual or potential use of the ocean resources. With this information release rates within acceptable limits for man and the ecosystem can then be determined. Today, probably the only situations which apply this approach are the controlled disposal of radioactive wastes. In this paper a recent radiological assessment of the dumping of packaged radioactive wastes on the seabed is discussed and some environmental aspects of the United States Department of Energy program are described examining the feasibility of the emplacement of contained radioactive wastes within the deep ocean sediments

  9. Dumping of radioactive waste in the Barents and Kara seas

    International Nuclear Information System (INIS)

    Salbu, B.; Christensen, G.C.

    1995-01-01

    To evaluate the level of radioactive contamination in the Kara Sea and to assess short- and long-term consequences of dumped radioactive waste, joint Russian-Norwegian expeditions have been performed annually since 1992. Results from the 1992 joint expedition to the Kara Sea demonstrated very low concentrations of radionuclides in waters and sediments. Contributions from different sources: global fallout, river transport, marine transport of discharges from European reprocessing plants and of fallout from Chernobyl, could be identified. From the expeditions in 1993 and 1994 to three bays at Novaya Zemlya, local contamination in the Stepovogo and the Abrosimov bays due to leakage from the dumped radioactive waste could be confirmed. Results from the 1994 expedition will be published in 1995. The levels of radioactivity in the Kara Sea are, however, very low and represent at present an extremely low impact on man and the marine ecosystem. (Author)

  10. Ocean dumping of low-level radioactive wastes

    International Nuclear Information System (INIS)

    Templeton, W.L.

    1982-10-01

    Scientific bases, developed internationally over the last 20 years, to control and restrict to acceptable levels the resultant radiation doses that potentially could occur from the dumping of low-level radioactive wastes in the deep oceans were presented. The author concluded that present evaluations of the disposal of radioactive wastes into the oceans, coastal and deep ocean, indicate that these are being conducted within the ICRP recommended dose limits. However, there are presently no international institutions or mechanisms to deal with the long-term radiation exposure at low-levels to large numbers of people on a regional basis if not a global level. Recommendations were made to deal with these aspects through the established mechanisms of NEA/OECD and the London Dumping Convention, in cooperation with ICRP, UNSCEAR and the IAEA

  11. Biological reduction of dust nuisance on power station waste dumps

    Energy Technology Data Exchange (ETDEWEB)

    Kozel, J

    1978-01-01

    The results of pot trials and succeeding field trials carried out in 1966-72 to find out the best method of reclamationand stabilishing the fly ash and cinder waste dump at the Melnik power station are summarised. The material consists mainly of fine particles with a size range of less than 1 micron to 0.16 mm in diam., and creates a source of blown dust in dry weather. Treatment of the waste material before sowing grass and legume species, the species tested, sowing rates, applied fertilizers, irrigation and treatment of the resulting swards are discussed. The most suitable species were Festuca rubra, F. ovina, perennial ryegrass and Italian ryegrass; the cost of stabilising the dump was lowest with Italian ryegrass. (In English)

  12. Experimental use of neutrinos from ISABELLE beam dumps

    International Nuclear Information System (INIS)

    Bozoki, G.E.; Thorndike, A.M.; Mann, A.K.

    1978-01-01

    The technical feasibility and possible applicability of using ISABELLE beam dumps as powerful sources for directed high-energy neutrino bursts are investigated. In the present machine design two dump systems are applied to absorb the extracted fast beams. The expected normal beam extraction rate is 1 to 2 per day, when about (6.3 to 7.5) x 10 14 protons are hitting the external targets during a pulse length of approx. 50 μs. These protons are considered so far to be useless. The neutrinos produced could be used for the following activities: the study of coherent neutrino regeneration, calibration and permanent testing of cosmic-ray and astrophysical neutrino detectors, research on the practical applicability of neutrinos in telecommunication, and certain astro- and geophysical applications. Tailoring the system to meet these activities is illustrated. 6 figures

  13. Acute pseudo-obstruction of the colon

    International Nuclear Information System (INIS)

    Beese, M.; Heller, M.

    1988-01-01

    The radiological correlate to the pseudo-obstruction of the colon is not specific, but it does supply a pointer to the disease of it shows dilation of the caecum, colon ascendens and colon transversum with air-pockets and reflected imaging as well as a usually not dilated colon descendens with remarkably little air. To make the diagnosis quite sure we must exclude intestinal obstruction by using X-ray contrast media or by coloscopy. (orig./GDG) [de

  14. Quality pseudo-random number generator

    International Nuclear Information System (INIS)

    Tarasiuk, J.

    1996-01-01

    The pseudo-random number generator (RNG) was written to match needs of nuclear and high-energy physics computation which in some cases require very long and independent random number sequences. In this random number generator the repetition period is about 10 36 what should be sufficient for all computers in the world. In this article the test results of RNG correlation, speed and identity of computations for PC, Sun4 and VAX computer tests are presented

  15. SPS accelerating cavity

    CERN Multimedia

    CERN PhotoLab

    1976-01-01

    The SPS started up with 2 accelerating cavities (each consisting of 5 tank sections) in LSS3. They have a 200 MHz travelling wave structure (see 7411032 and 7802190) and 750 kW of power is fed to each of the cavities from a 1 MW tetrode power amplifier, located in a surface building above, via a coaxial transmission line. Clemens Zettler, builder of the SPS RF system, is standing at the side of one of the cavities. In 1978 and 1979 another 2 cavities were added and entered service in 1980. These were part of the intensity improvement programme and served well for the new role of the SPS as proton-antiproton collider. See also 7411032, 8011289, 8104138, 8302397.

  16. Dental Sealants Prevent Cavities

    Science.gov (United States)

    ... Digital Press Kit Read the MMWR Science Clips Dental Sealants Prevent Cavities Effective protection for children Language: ... more use of sealants and reimbursement of services. Dental care providers can Apply sealants to children at ...

  17. Statistical electromagnetics: Complex cavities

    NARCIS (Netherlands)

    Naus, H.W.L.

    2008-01-01

    A selection of the literature on the statistical description of electromagnetic fields and complex cavities is concisely reviewed. Some essential concepts, for example, the application of the central limit theorem and the maximum entropy principle, are scrutinized. Implicit assumptions, biased

  18. accelerating cavity from LEP

    CERN Multimedia

    This is an accelerating cavity from LEP, with a layer of niobium on the inside. Operating at 4.2 degrees above absolute zero, the niobium is superconducting and carries an accelerating field of 6 million volts per metre with negligible losses. Each cavity has a surface of 6 m2. The niobium layer is only 1.2 microns thick, ten times thinner than a hair. Such a large area had never been coated to such a high accuracy. A speck of dust could ruin the performance of the whole cavity so the work had to be done in an extremely clean environment. These challenging requirements pushed European industry to new achievements. 256 of these cavities are now used in LEP to double the energy of the particle beams.

  19. Environmental assessment methodologies for sea dumping of radioactive wastes

    International Nuclear Information System (INIS)

    1983-09-01

    The IAEA and the IMO, in cooperation with the United Nations Environment Programme (UNEP), jointly convened a Technical Committee to provide guidance to national authorities. This document contains the results of the Technical Committee Meeting in Vienna, August - September 1982 and constitutes guidance to the Contracting Parties to the LDC Convention on the nature and content of the environmental assessment required for permit applications for sea dumping of radioactive wastes

  20. Modeling of air pollution from the power plant ash dumps

    Science.gov (United States)

    Aleksic, Nenad M.; Balać, Nedeljko

    A simple model of air pollution from power plant ash dumps is presented, with emission rates calculated from the Bagnold formula and transport simulated by the ATDL type model. Moisture effects are accounted for by assumption that there is no pollution on rain days. Annual mean daily sedimentation rates, calculated for the area around the 'Nikola Tesla' power plants near Belgrade for 1987, show reasonably good agreement with observations.

  1. Modeling of air pollution from the power plant ash dumps

    Energy Technology Data Exchange (ETDEWEB)

    Aleksic, N M; Balac, N [Institute of Meteorology, Belgrade (Yugoslavia). College of Physics

    1991-01-01

    A simple model of air pollution from power plant ash dumps is presented, with emission rates calculated from the Bagnold formula and transport simulated by the ATDL (Atmospheric Turbulence and Diffusion Laboratory) type model. Moisture effects are accounted for by assumption that there is no pollution on rain days. Annual mean daily sedimentation rates, calculated for the area around the Nikola Tesla power plants near Belgrade for 1987, show reasonably good agreement with observations. 3 refs., 2 figs., 2 tabs.

  2. Energy deposition profile on ISOLDE Beam Dumps by FLUKA simulations

    CERN Document Server

    Vlachoudis, V

    2014-01-01

    In this report an estimation of the energy deposited on the current ISOLDE beam dumps obtained by means of FLUKA simulation code is presented. This is done for both ones GPS and HRS. Some estimations of temperature raise are given based on the assumption of adiabatic increase from energy deposited by the impinging protons. However, the results obtained here in relation to temperature are only a rough estimate. They are meant to be further studied through thermomechanical simulations using the energyprofiles hereby obtained.

  3. Assessment of the mercury emissions from burning mining waste dumps

    Directory of Open Access Journals (Sweden)

    Barbara Białecka

    2016-04-01

    occur and to which the environment and local inhabitants can be exposed, it is important to define the size of the emission of mercury compounds from these objects. Despite the potential threats so far no measurements of mercury concentration which would a llow quantifying this phenomenon have been done. The analyses presented in this article fill this gap. Additionally, initial calculation of annual mercury emissions from burning coal mining waste dumps in Poland is presented.

  4. Hybrid vertical cavity laser

    DEFF Research Database (Denmark)

    Chung, Il-Sug; Mørk, Jesper

    2010-01-01

    A new hybrid vertical cavity laser structure for silicon photonics is suggested and numerically investigated. It incorporates a silicon subwavelength grating as a mirror and a lateral output coupler to a silicon ridge waveguide.......A new hybrid vertical cavity laser structure for silicon photonics is suggested and numerically investigated. It incorporates a silicon subwavelength grating as a mirror and a lateral output coupler to a silicon ridge waveguide....

  5. American Material Culture: Investigating a World War II Trash Dump

    Energy Technology Data Exchange (ETDEWEB)

    Julie Braun

    2005-10-01

    The Idaho National Laboratory: An Historical Trash Trove Historians and archaeologists love trash, the older the better. Sometimes these researchers find their passion in unexpected places. In this presentation, the treasures found in a large historic dump that lies relatively untouched in the middle of the Idaho National Laboratory (INL) will be described. The U.S. military used the central portion of the INL as one of only six naval proving grounds during World War II. They dumped trash in dry irrigation canals during and after their wartime activities and shortly before the federal government designated this arid and desolate place as the nation’s nuclear reactor testing station in 1949. When read critically and combined with memories and photographs, the 60-year old trash provides a glimpse into 1940s’ culture and the everyday lives of ordinary people who lived and worked during this time on Idaho’s desert. Thanks to priceless stories, hours of research, and the ability to read the language of historic artifacts, the dump was turned from just another trash heap into a treasure trove of 1940s memorabilia. Such studies of American material culture serve to fire our imaginations, enrich our understanding of past practices, and humanize history. Historical archaeology provides opportunities to integrate inanimate objects with animated narrative and, the more recent the artifacts, the more human the stories they can tell.

  6. Environmental assessment methodologies for sea dumping of radioactive wastes

    International Nuclear Information System (INIS)

    1984-01-01

    This document, which describes the content of an environmental assessment report, will assist national authorities to meet their obligations under the London Dumping Convention (LDC, 1972) by initiating those steps which are to be undertaken to ensure that ''the procedure to be followed and the nature of such reports shall be agreed by the parties in consultation'' (Article VI. 4). In the context of sea disposal of radioactive wastes, environmental assessments are taken to mean those evaluations which are undertaken to assist in the decision-making processes used by national authorities to determine: 1) How the option of sea disposal compares environmentally, technically, socially and economically with other disposal options (this constitutes the comparison with land-based alternatives); and 2) Whether the impact of a proposed sea disposal option is acceptable (this requires a detailed evaluation of the proposed operation including site selection, quantities and types of waste to be dumped, operational requirements and calculation of radiological and other risks). The term ''environmental assessment'' in these respects is deemed to include both the evaluation of the impact of sea dumping and the document that describes this evaluation

  7. Irradiation Effects on RIA Fragmentation Cu Beam Dump

    CERN Document Server

    Reyes, Susana; Boles, Jason; Stein, Werner; Wirth, Brian

    2005-01-01

    Within the scope of conceptual R&D activities in support of the Rare-Isotope Accelerator (RIA) facility, high priority is given to the development of high-power fragmentation beam dumps. A pre-study was made of a static water-cooled Cu beam dump that can meet requirements for a 400 MeV/u uranium beam. The issue of beam sputtering was addressed and found to be not a significant issue. Preliminary radiation transport simulations show significant damage (dpa) in the vicinity of the Bragg peak of uranium ions. Experimental data show that defects in Cu following neutron or high-energy particle irradiation tend to saturate at doses between 1 and 5 dpa, and this saturation in defect density also results in saturation of mechanical property degradation. However, effects of swift heavy ion irradiation and the production of gaseous and solid transmutant elements still need to be addressed. Initial calculations indicate that He concentrations on the order of 100 appm are produced in the beam dump after several weeks...

  8. Detailed mechanical design of the LIPAc beam dump radiological shielding

    Energy Technology Data Exchange (ETDEWEB)

    Nomen, Oriol, E-mail: onomen@irec.cat [IREC, Barcelona, Catalonia (Spain); CDEI-UPC, Barcelona, Catalonia (Spain); Martínez, José I.; Arranz, Fernando; Iglesias, Daniel; Barrera, Germán; Brañas, Beatriz [CIEMAT, Madrid (Spain); Ogando, Francisco [UNED, Madrid (Spain); Molla, Joaquín [CIEMAT, Madrid (Spain); Sanmartí, Manel [IREC, Barcelona, Catalonia (Spain)

    2013-10-15

    Highlights: ► Mechanical design of the IFMIF LIPAc beam dump shielding has been performed. ► Lead shutter design performed to shield radiation from beam dump when LIPAc is off. ► External loads, working and dismantling conditions, included as design constraints. -- Abstract: The LIPAc is a 9 MeV, D{sup +} linear prototype accelerator for the validation of the IFMIF accelerator design. The high intensity, 125 mA CW beam is stopped in a copper cone involving a high production of neutrons and gamma radiation and activation of its surface. The beam stopper is surrounded by a shielding to attenuate the resulting radiation so that dose rate values comply with the limits at the different zones of the installation. The shielding includes for that purpose polyethylene rings, water tanks and gray cast iron rings. A lead shutter has also been designed to shield the gamma radiation that comes through the beam tube when the linear accelerator is not in operation, in order to allow access inside the building for maintenance tasks. The present work summarizes the detailed mechanical design of the beam dump shielding and the lead shutter taking into account the design constraints, such as working conditions and other external loads, as well as including provisions for dismantling.

  9. The IFMIF-EVEDA accelerator beam dump design

    International Nuclear Information System (INIS)

    Iglesias, D.; Arranz, F.; Arroyo, J.M.; Barrera, G.; Branas, B.; Casal, N.; Garcia, M.; Lopez, D.; Martinez, J.I.; Mayoral, A.; Ogando, F.; Parro, M.; Oliver, C.; Rapisarda, D.; Sanz, J.; Sauvan, P.; Ibarra, A.

    2011-01-01

    The IFMIF-EVEDA accelerator will be a 9 MeV, 125 mA cw deuteron accelerator prototype for verifying the validity of the 40 MeV accelerator design for IFMIF. A beam dump designed for maximum power of 1.12 MW will be used to stop the beam at the accelerator exit. The conceptual design for the IFMIF-EVEDA accelerator beam dump is based on a conical beam stop made of OFE copper. The cooling system uses an axial high velocity flow of water pressurized up to 3.4 x 10 5 Pa to avoid boiling. The design has been shown to be compliant with ASME mechanical design rules under nominal full power conditions. A sensitivity analysis has been performed to take into account the possible margin on the beam properties at the beam dump entrance. This analysis together with the study of the maintenance issues and the mounting and dismounting operations has led to the complete design definition.

  10. Design of a Compact Dump Resistor System for LCD Magnet

    CERN Document Server

    Gaddi, A

    2010-01-01

    In this technical note we suggest a possible solution for the choice of the detector magnet dump resistor. The push-pull scenario for Linear Collider Detectors imposes new solutions for magnet powering and protection lines, else than what developed for LHC detectors. The magnet dump resistor is the protecting equipment that has the function of extracting a significant amount of magnetic stored energy, from the coil winding to a dump. The LCD magnet has to move with the experiment from the garage to the beam position, so it has to be compact and reliable at the same time. We make here a proposal for a passive water-cooled dumper, we calculate the minimum amount of water required, the resistor hot-spot temperature, the overall mechanical design. The electrical part is not covered by this note, as it can be assumed that the solutions adopted by LHC detector magnets, in terms of quench instrumentation, energy extraction and maximum voltage, are not significantly affected by the push-pull scenario.

  11. Resonant production of dark photons in positron beam dump experiments

    Science.gov (United States)

    Nardi, Enrico; Carvajal, Cristian D. R.; Ghoshal, Anish; Meloni, Davide; Raggi, Mauro

    2018-05-01

    Positrons beam dump experiments have unique features to search for very narrow resonances coupled superweakly to e+e- pairs. Due to the continued loss of energy from soft photon bremsstrahlung, in the first few radiation lengths of the dump a positron beam can continuously scan for resonant production of new resonances via e+ annihilation off an atomic e- in the target. In the case of a dark photon A' kinetically mixed with the photon, this production mode is of first order in the electromagnetic coupling α , and thus parametrically enhanced with respect to the O (α2)e+e-→γ A' production mode and to the O (α3)A' bremsstrahlung in e- -nucleon scattering so far considered. If the lifetime is sufficiently long to allow the A' to exit the dump, A'→e+e- decays could be easily detected and distinguished from backgrounds. We explore the foreseeable sensitivity of the Frascati PADME experiment in searching with this technique for the 17 MeV dark photon invoked to explain the Be 8 anomaly in nuclear transitions.

  12. Phytoremediation of coal mine spoil dump through integrated biotechnological approach

    Energy Technology Data Exchange (ETDEWEB)

    Juwarkar, A.A.; Jambhulkar, H.P. [National Environmental Engineering Research Institute, Nagpur (India)

    2008-07-15

    Field experiment was conducted on mine spoil dump on an area of 10 ha, to restore the fertility and productivity of the coal mine spoil dump using integrated biotechnological approach. The approach involves use of effluent treatment plant sludge (ETP sludge), as an organic amendment, biofertilizers and mycorrihzal fungi along with suitable plant species. The results of the study indicated that amendment with effluent treatment plant sludge (ETP sludge), at 50 ton/ha improved the physico-chemical properties of coal mine spoil. Due to biofertilizer inoculation different microbial groups such as Rhizobium, Azotobacter and VAM spores, which were practically absent in mine spoil improved greatly. Inoculation of biofertilizer and application of ETP sludge helped in reducing the toxicity of heavy metals such as chromium, zinc, copper, iron, manganese lead, nickel and cadmium, which were significantly reduced to 41%, 43%, 37%, 37%, 34%, 39%, 37% and 40%, respectively, due to the increased organic matter content in the ETP sludge and its alkaline pH (8.10-8.28), at which the metals gets immobilized and translocation of metals is arrested. Thus, amendment and biofertilizer application provided better supportive material for anchorage and growth of the plant on coal mine spoil dump.

  13. The Superconducting TESLA Cavities

    CERN Document Server

    Aune, B.; Bloess, D.; Bonin, B.; Bosotti, A.; Champion, M.; Crawford, C.; Deppe, G.; Dwersteg, B.; Edwards, D.A.; Edwards, H.T.; Ferrario, M.; Fouaidy, M.; Gall, P-D.; Gamp, A.; Gössel, A.; Graber, J.; Hubert, D.; Hüning, M.; Juillard, M.; Junquera, T.; Kaiser, H.; Kreps, G.; Kuchnir, M.; Lange, R.; Leenen, M.; Liepe, M.; Lilje, L.; Matheisen, A.; Möller, W-D.; Mosnier, A.; Padamsee, H.; Pagani, C.; Pekeler, M.; Peters, H-B.; Peters, O.; Proch, D.; Rehlich, K.; Reschke, D.; Safa, H.; Schilcher, T.; Schmüser, P.; Sekutowicz, J.; Simrock, S.; Singer, W.; Tigner, M.; Trines, D.; Twarowski, K.; Weichert, G.; Weisend, J.; Wojtkiewicz, J.; Wolff, S.; Zapfe, K.

    2000-01-01

    The conceptional design of the proposed linear electron-positron colliderTESLA is based on 9-cell 1.3 GHz superconducting niobium cavities with anaccelerating gradient of Eacc >= 25 MV/m at a quality factor Q0 > 5E+9. Thedesign goal for the cavities of the TESLA Test Facility (TTF) linac was set tothe more moderate value of Eacc >= 15 MV/m. In a first series of 27industrially produced TTF cavities the average gradient at Q0 = 5E+9 wasmeasured to be 20.1 +- 6.2 MV/m, excluding a few cavities suffering fromserious fabrication or material defects. In the second production of 24 TTFcavities additional quality control measures were introduced, in particular aneddy-current scan to eliminate niobium sheets with foreign material inclusionsand stringent prescriptions for carrying out the electron-beam welds. Theaverage gradient of these cavities at Q0 = 5E+9 amounts to 25.0 +- 3.2 MV/mwith the exception of one cavity suffering from a weld defect. Hence only amoderate improvement in production and preparation technique...

  14. Wavefield Extrapolation in Pseudo-depth Domain

    KAUST Repository

    Ma, Xuxin

    2011-12-11

    Wave-equation based seismic migration and inversion tools are widely used by the energy industry to explore hydrocarbon and mineral resources. By design, most of these techniques simulate wave propagation in a space domain with the vertical axis being depth measured from the surface. Vertical depth is popular because it is a straightforward mapping of the subsurface space. It is, however, not computationally cost-effective because the wavelength changes with local elastic wave velocity, which in general increases with depth in the Earth. As a result, the sampling per wavelength also increases with depth. To avoid spatial aliasing in deep fast media, the seismic wave is oversampled in shallow slow media and therefore increase the total computation cost. This issue is effectively tackled by using the vertical time axis instead of vertical depth. This is because in a vertical time representation, the "wavelength" is essentially time period for vertical rays. This thesis extends the vertical time axis to the pseudo-depth axis, which features distance unit while preserving the properties of the vertical time representation. To explore the potentials of doing wave-equation based imaging in the pseudo-depth domain, a Partial Differential Equation (PDE) is derived to describe acoustic wave in this new domain. This new PDE is inherently anisotropic because the use of a constant vertical velocity to convert between depth and vertical time. Such anisotropy results in lower reflection coefficients compared with conventional space domain modeling results. This feature is helpful to suppress the low wavenumber artifacts in reverse-time migration images, which are caused by the widely used cross-correlation imaging condition. This thesis illustrates modeling acoustic waves in both conventional space domain and pseudo-depth domain. The numerical tool used to model acoustic waves is built based on the lowrank approximation of Fourier integral operators. To investigate the potential

  15. Construction of the mathematical concept of pseudo thinking students

    Science.gov (United States)

    Anggraini, D.; Kusmayadi, T. A.; Pramudya, I.

    2018-05-01

    Thinking process is a process that begins with the acceptance of information, information processing and information calling in memory with structural changes that include concepts or knowledges. The concept or knowledge is individually constructed by each individual. While, students construct a mathematical concept, students may experience pseudo thinking. Pseudo thinking is a thinking process that results in an answer to a problem or construction to a concept “that is not true”. Pseudo thinking can be classified into two forms there are true pseudo and false pseudo. The construction of mathematical concepts in students of pseudo thinking should be immediately known because the error will have an impact on the next construction of mathematical concepts and to correct the errors it requires knowledge of the source of the error. Therefore, in this article will be discussed thinking process in constructing of mathematical concepts in students who experience pseudo thinking.

  16. Development of offroad unmanned dump truck navigation system. Dump truck mujin soko system no kaihatsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Horii, Z [Nittetsu Mining Co. Ltd., Tokyo (Japan)

    1992-08-25

    A large offroad unmanned dump truck navigation system has been developed, and is in practical operation mounted on dump trucks at Torigatayama Limestone Quarry of Nittetsu Mining Company. The system functions in a manual dump truck navigation mode, wireless navigation mode, and unmanned control mode. The unmanned control mode further includes a mode to navigate the truck on a predetermined course with its data having been input in a computer and a mode that when the truck was moved on a course under a wireless control, the computer learns the course and drives the truck autonomously thereafter. The safety measures are divided into the hardware safety function to detect abnormalities in brakes and other vehicle parts, and the software safety functions of data communications, sensor action check, and prevention of collision of trucks with each other. The system has resulted in a productivity of average one-way travel distance of 345 m, and average unmanned navigation cycle time of 9 minutes and 26 seconds for a transportation efficiency of 541 t/hour/truck, having reached at least the manned operation level. 4 figs., 1 tab.

  17. Influence of coal ash and slag dumping on dump waste waters of the Kostolac power plants (Serbia)

    Energy Technology Data Exchange (ETDEWEB)

    Popovic, A.; Djinovic, J. [University of Belgrade, Belgrade (Serbia)

    2006-10-01

    The content of selected trace and major elements in the river water used for transport, as well as in the subcategories of the waste waters (overflow and drainage) were analyzed in order to establish the influence of transport and dumping of coal ash and slag from the 'Kostolac A' and 'Kostolac B' power plants located 100 km from Belgrade (Serbia). It was found that during transport of coal ash and slag to the dump, the water used for transport becomes enriched with manganese, nickel, zinc, chromium, vanadium, titanium, cobalt, arsenic, aluminum, and silicon, while more calcium, iron, cadmium, and lead are adsorbed by the ash and slag than is released from them. There is also an equilibrium between the release and adsorption processes of copper and magnesium during transport. The vertical penetration of the water used for transport results in a release of calcium, magnesium, manganese, and cadmium to the environment, while iron, nickel, zinc, chromium, copper, lead, vanadium, titanium, cobalt, and arsenic are adsorbed by the fractions of coal ash and slag in the dump.

  18. Contribution to the study of 'Pseudo-spark' discharges applied to the realisation of latch devices

    International Nuclear Information System (INIS)

    Bauville, Gerard

    1994-01-01

    The objective of this research thesis is to study discharges growing from a hollow geometry of electrodes for pressures on the left side of the Paschen minimum. The study characterises the main conduction phase by experimentally determining the discharge voltage and current. Based on a numerical analysis, the author deduces some macroscopic characteristics such as voltage mean value, dissipated energy, with respect to the variation of various parameters such as gas pressure and nature, discharge duration, and electrode cavity geometries. After a first part on switches (technological applications, switches, pseudo-spark breakers), the author addresses the discharges (presentation of a 'pseudo-spark'-type discharge, involved physical mechanisms, methods of initiation of pseudo-spark discharges, triggering by a magnetic field pulse). The next part describes the test bench in a detailed way (electrodes, triggering system, electric configurations), and the last part reports the experimental study. It addresses the following issues: distribution of magnetic field lines, voltage drop, conjunction phase, discharge footprints on the surfaces, propagation rate, disjunction [fr

  19. Dumping of low-level radioactive waste in the deep ocean

    International Nuclear Information System (INIS)

    Templeton, W.L.

    1980-01-01

    Two international agreements relate to the dumping of packaged radioactive waste into the oceans - the Convention on the Prevention of Marine Pollution by Dumping Wastes and Other Matter of 1972 (London Convention) and the Multilateral Consultation and Surveillance Mechanism for Sea Dumping of Radioactive Waste of 1977 under the Organization for Economic Co-operation and Development (OECD). The International Atomic Energy Agency was given the responsibility to define high-level radioactive wastes which are unsuitable for dumping in the oceans and to make recommendations for the dumping of other radioactive wastes. A revised Definition and Recommendations was submitted and accepted by the London Convention. This paper reviews the technical basis for the Definition and describes how it has been applied to the radiological assessment of the only operational dumping site in the North East Atlantic

  20. Alternative power supply and dump resistor connections for similar, mutually coupled, superconducting coils

    International Nuclear Information System (INIS)

    Owen, E.W.; Shimer, W.; Wang, S.T.

    1983-01-01

    Alternative methods of connecting similar mutually coupled coils to their power supplies and dump resistors are investigated. The circuits are evaluated for both operating and fault conditions. The factors considered are the voltage to ground during a dump, short circuits, open circuits, quenches, and failure of the protection system to detect a quench. Of particular interest are the currents induced in coils that remain superconducting when one or more coils quench. The alternative connections include combined power supplies, individual dump resistors, combined resistors and series and parallel dump resistors. A new circuit that contains ''coupling'' resistors is proposed. The coupling resistors do not affect normal fast dumps but reduce the peak induced currents while also reducing the energy rating of the dump resistors. Another novel circuit, the series circuit with diodes, is discussed. The MFTF-B central-cell solenoids are used as an example

  1. Alternative power supply and dump resistor connections for similar, mutally coupled, superconducting coils

    International Nuclear Information System (INIS)

    Owen, E.W.; Shimer, D.W.; Wang, S.T.

    1983-01-01

    Alternative methods of connecting similar mutually coupled coils to their power supplies and dump resistors are investigated. The circuits are evaluated for both operating and fault conditions. The factors considered are the voltage to ground during a dump, short circuits, open circuits, quenches, and failure of the protection system to detect a quench. Of particular interest are the currents induced in coils that remain superconducting when one or more coils quench. The alternative connections include combined power supplies, individual dump resistors, combined resistors and series and parallel dump resistors. A new circuit that contains coupling resistors is proposed. The coupling resistors do not affect normal fast dumps but reduce the peak induced currents while also reducing the energy rating of the dump resistors. Another novel circuit, the series circuit with diodes, is discussed. The MFTF-B central-cell solenoids are used as an example

  2. Reclamation of the illegal dump for sustainable development the environment in Sverdlovo of Leningrad Oblast’, Russia

    Directory of Open Access Journals (Sweden)

    Bukova Maria

    2016-01-01

    Full Text Available Illegal dumping is dumping of any waste such as oil, furniture, appliances, trash, litter or landscaping cuttings, upon any land of state, city, village or private ownership without consent of the owner. Illegal dumping has a great negative and fatal impact on our environment and all living organisms both fauna and flora. It also exposes people to various risks of chemicals (fluids or dust and is a big threat to all under-ground and surface water resources. Illegal dumps also attract all kinds of bugs such as rodents and insects. For example, illegal dumps with waste tires provide a practically perfect place for mosquitoes to breed. Mosquitoes can multiply 100 times faster than normal in the warm, stagnant water in waste tires. Exemplary for the illegal dump in Sverdlovo of Leningrad Oblast’ the main purpose of this article is to offer a possible option for the remediation of contaminated area.

  3. Variation of leaf margin serration in Populus nigra of industrial dumps

    Directory of Open Access Journals (Sweden)

    Yu. A. Shtirs

    2017-07-01

    Full Text Available The variability of leaf margin serration of Populus nigra L. in conditions of industrial dumps (coal mines dumps and overburden dumps and city park is estimated. The value of this indicator is in the range from 1.25 to 1.76 and significantly increases along the gradient: coal mines dumps – overburden dumps – city park. From the number of selected gradations of P. nigra leaf blades, the gradation with values of 1.45-1.55 is most pronounced according to the analyzed index for industrial dumps, for the park – with the values of 1.55-1.65. The degree of serration of edge leaf blade is characterized by low values of variation – coefficient of variation is less than 10.0%. We registered the significant positive correlation between the average values of leaf margin serration and the length of P. nigra leaf blade.

  4. Pseudo-communication vs Quasi-communication

    Directory of Open Access Journals (Sweden)

    Елена Константиновна Черничкина

    2016-12-01

    Full Text Available The article is devoted to the analysis of such specific forms of human interaction as quasi- and pseudo-communication. The authors specify the terms which sometimes are used interchangeably. The aim of the conducted research is to find out and demonstrate existing differences and similarities of these communicative phenomena on the basis of theoretical and empirical analysis of the research material in the Russian and English languages. The authors describe communicative features of these phenomena and consider the reasons for such forms of communication and their increased use at present. The research material is represented fiction extracts, film scripts, jokes, print media, a collection of oral speech records both in Russian and English. The authors make use of the following research methods: definitional analysis (to define the terminology of the research, the method of linguistic observation and introspection (to select the communicative situations, the descriptive-analytical method and the method of comparative analysis (to identify similarities and differences of the target phenomena, and the conversational analysis method (to view productivity and effectiveness of a dialogue, etc. The classification of possible forms of their existence in different discourses is suggested. The authors assume that both pseudo- and quasi-communication are characterized as fictitious forms of human interaction with some noticeable violation of the basic communicative model. Pseudo-communication suffers from the discrepancy of the meaning of a coded and decoded message. The authors put forward the main parameters of scientific classification of it as follows: adequate understanding, intentionality, and the stage of communicative action where the failure takes place. At the same time they stress the necessity to distinguish the cases of pseudo talks from phatic and indirect communication. Quasi-communcation is marked by the lack of a real partner and hence

  5. Pseudo-Hermitian random matrix theory

    International Nuclear Information System (INIS)

    Srivastava, S.C.L.; Jain, S.R.

    2013-01-01

    Complex extension of quantum mechanics and the discovery of pseudo-unitarily invariant random matrix theory has set the stage for a number of applications of these concepts in physics. We briefly review the basic ideas and present applications to problems in statistical mechanics where new results have become possible. We have found it important to mention the precise directions where advances could be made if further results become available. (Copyright copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  6. Pseudo ventricular tachycardia: a case report.

    LENUS (Irish Health Repository)

    Riaz, A

    2012-02-01

    BACKGROUND: Dramatic artifacts of pseudo flutter have been reported in the past secondary to various factors including tremor (Handwerker and Raptopoulos in N Engl J Med 356:503, 2007) and dialysis machines (Kostis et al. in J Electrocardiol 40(4):316-318, 2007). METHODS: We present this unusual case where the artifact, produced by tremor, was so pronounced to be misdiagnosed and treated as ventricular tachycardia. CONCLUSION: This case highlights the importance of correlating ECG findings with history and clinical examination and of using 12 lead ECGs for rhythm interpretation especially to confirm consistence of arrhythmias in all leads.

  7. Robust Pseudo-Hierarchical Support Vector Clustering

    DEFF Research Database (Denmark)

    Hansen, Michael Sass; Sjöstrand, Karl; Olafsdóttir, Hildur

    2007-01-01

    Support vector clustering (SVC) has proven an efficient algorithm for clustering of noisy and high-dimensional data sets, with applications within many fields of research. An inherent problem, however, has been setting the parameters of the SVC algorithm. Using the recent emergence of a method...... for calculating the entire regularization path of the support vector domain description, we propose a fast method for robust pseudo-hierarchical support vector clustering (HSVC). The method is demonstrated to work well on generated data, as well as for detecting ischemic segments from multidimensional myocardial...

  8. Inflation and pseudo-Goldstone Higgs boson

    DEFF Research Database (Denmark)

    Alanne, Tommi; Sannino, Francesco; Tenkanen, Tommi

    2017-01-01

    We consider inflation within a model framework where the Higgs boson arises as a pseudo-Goldstone boson associated with the breaking of a global symmetry at a scale significantly larger than the electroweak one. We show that in such a model the scalar self-couplings can be parametrically suppressed...... and, consequently, the nonminimal couplings to gravity can be of order one or less, while the inflationary predictions of the model remain compatible with the precision cosmological observations. Furthermore, in the model we study, the existence of the electroweak scale is entirely due to the inflaton...

  9. Video Toroid Cavity Imager

    Energy Technology Data Exchange (ETDEWEB)

    Gerald, Rex E. II; Sanchez, Jairo; Rathke, Jerome W.

    2004-08-10

    A video toroid cavity imager for in situ measurement of electrochemical properties of an electrolytic material sample includes a cylindrical toroid cavity resonator containing the sample and employs NMR and video imaging for providing high-resolution spectral and visual information of molecular characteristics of the sample on a real-time basis. A large magnetic field is applied to the sample under controlled temperature and pressure conditions to simultaneously provide NMR spectroscopy and video imaging capabilities for investigating electrochemical transformations of materials or the evolution of long-range molecular aggregation during cooling of hydrocarbon melts. The video toroid cavity imager includes a miniature commercial video camera with an adjustable lens, a modified compression coin cell imager with a fiat circular principal detector element, and a sample mounted on a transparent circular glass disk, and provides NMR information as well as a video image of a sample, such as a polymer film, with micrometer resolution.

  10. Metasurface external cavity laser

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Luyao, E-mail: luyaoxu.ee@ucla.edu; Curwen, Christopher A.; Williams, Benjamin S. [Department of Electrical Engineering, University of California, Los Angeles, California 90095 (United States); California NanoSystems Institute, University of California, Los Angeles, California 90095 (United States); Hon, Philip W. C.; Itoh, Tatsuo [Department of Electrical Engineering, University of California, Los Angeles, California 90095 (United States); Chen, Qi-Sheng [Northrop Grumman Aerospace Systems, Redondo Beach, California 90278 (United States)

    2015-11-30

    A vertical-external-cavity surface-emitting-laser is demonstrated in the terahertz range, which is based upon an amplifying metasurface reflector composed of a sub-wavelength array of antenna-coupled quantum-cascade sub-cavities. Lasing is possible when the metasurface reflector is placed into a low-loss external cavity such that the external cavity—not the sub-cavities—determines the beam properties. A near-Gaussian beam of 4.3° × 5.1° divergence is observed and an output power level >5 mW is achieved. The polarized response of the metasurface allows the use of a wire-grid polarizer as an output coupler that is continuously tunable.

  11. Initial results from beam commissioning of the LHC beam dump system

    CERN Document Server

    Goddard, B; Carlier, E; Ducimetière, L; Gallet, E; Gyr, M; Jensen, L; Jones, R; Kain, V; Kramer, T; Lamont, M; Meddahi, M; Mertens, V; Risselada, Thys; Uythoven, J; Wenninger, J; Weterings, W

    2010-01-01

    Initial commissioning of the LHC beam dump system with beam took place in August and September 2008. The preparation, setting-up and the tests performed are described together with results of the extractions of beam into the dump lines. Analysis of the first detailed aperture measurements of the extraction channels and kicker performance derived from dilution sweep shapes are presented. The performance of the other equipment subsystems is summarised, in particular that of the dedicated dump system beam instrumentation.

  12. Earth-ionosphere cavity

    International Nuclear Information System (INIS)

    Tran, A.; Polk, C.

    1976-01-01

    To analyze ELF wave propagation in the earth-ionosphere cavity, a flat earth approximation may be derived from the exact equations, which are applicable to the spherical cavity, by introducing a second-order or Debye approximation for the spherical Hankel functions. In the frequency range 3 to 30 Hz, however, the assumed conditions for the Debye approximation are not satisfied. For this reason an exact evaluation of the spherical Hankel functions is used to study the effects of the flat earth approximation on various propagation and resonance parameters. By comparing the resonance equation for a spherical cavity with its flat earth counterpart and by assuming that the surface impedance Z/sub i/ at the upper cavity boundary is known, the relation between the eigenvalue ν and S/sub v/, the sine of the complex angle of incidence at the lower ionosphere boundary, is established as ν(ν + 1) = (kaS/sub v/) 2 . It is also shown that the approximation ν(ν + 1) approximately equals (ν + 1/2) 2 which was used by some authors is not adequate below 30 Hz. Numerical results for both spherical and planar stratification show that (1) planar stratification is adequate for the computation of the lowest three ELF resonance frequencies to within 0.1 Hz; (2) planar stratification will lead to errors in cavity Q and wave attenuation which increase with frequency; (3) computation of resonance frequencies to within 0.1 Hz requires the extension of the lower boundary of the ionosphere to a height where the ratio of conduction current to displacement current, (sigma/ωepsilon 0 ), is less than 0.3; (4) atmospheric conductivity should be considered down to ground level in computing cavity Q and wave attenuation

  13. Materials for superconducting cavities

    International Nuclear Information System (INIS)

    Bonin, B.

    1996-01-01

    The ideal material for superconducting cavities should exhibit a high critical temperature, a high critical field, and, above all, a low surface resistance. Unfortunately, these requirements can be conflicting and a compromise has to be found. To date, most superconducting cavities for accelerators are made of niobium. The reasons for this choice are discussed. Thin films of other materials such as NbN, Nb 3 Sn, or even YBCO compounds can also be envisaged and are presently investigated in various laboratories. It is shown that their success will depend critically on the crystalline perfection of these films. (author)

  14. Experimental investigation of cavity flows

    Energy Technology Data Exchange (ETDEWEB)

    Loeland, Tore

    1999-12-31

    This thesis uses LDV (Laser Doppler Velocimetry), PIV (Particle Image Velocimetry) and Laser Sheet flow Visualisation to study flow inside three different cavity configurations. For sloping cavities, the vortex structure inside the cavities is found to depend upon the flow direction past the cavity. The shape of the downstream corner is a key factor in destroying the boundary layer flow entering the cavity. The experimental results agree well with numerical simulations of the same geometrical configurations. The results of the investigations are used to find the influence of the cavity flow on the accuracy of the ultrasonic flowmeter. A method to compensate for the cavity velocities is suggested. It is found that the relative deviation caused by the cavity velocities depend linearly on the pipe flow. It appears that the flow inside the cavities should not be neglected as done in the draft for the ISO technical report on ultrasonic flowmeters. 58 refs., 147 figs., 2 tabs.

  15. Experimental investigation of cavity flows

    Energy Technology Data Exchange (ETDEWEB)

    Loeland, Tore

    1998-12-31

    This thesis uses LDV (Laser Doppler Velocimetry), PIV (Particle Image Velocimetry) and Laser Sheet flow Visualisation to study flow inside three different cavity configurations. For sloping cavities, the vortex structure inside the cavities is found to depend upon the flow direction past the cavity. The shape of the downstream corner is a key factor in destroying the boundary layer flow entering the cavity. The experimental results agree well with numerical simulations of the same geometrical configurations. The results of the investigations are used to find the influence of the cavity flow on the accuracy of the ultrasonic flowmeter. A method to compensate for the cavity velocities is suggested. It is found that the relative deviation caused by the cavity velocities depend linearly on the pipe flow. It appears that the flow inside the cavities should not be neglected as done in the draft for the ISO technical report on ultrasonic flowmeters. 58 refs., 147 figs., 2 tabs.

  16. Modeling acid mine drainage in waste rock dumps

    Energy Technology Data Exchange (ETDEWEB)

    Lefebvre, R. [INRS, Quebec (Canada)

    1995-03-01

    Acid mine drainage (AMD) results from the oxidation of sulfides present in mine wastes. The acidity generated by these reactions creates conditions under which metals can be leached and represent a threat for surface and ground waters. Even though leachate collection and neutralization are used to treat the problem, the industry is looking for methods to predict and prevent the generation of AMD at new sites and control methods for sites already producing AMD. Waste rock dumps are generally very large accumulations of barren rocks extracted from open pits to access ore bodies. These rocks contain sulfides, most commonly pyrite, and often generate AMD at rates much higher than in mine tailings which are fine grained by-products of milling operations. Numerous coupled physical processes are involved in AMD production in waste rocks. Sulfide oxidation reactions are strongly exothermic and temperatures beyond 70{degrees}C have been measured in some dumps. That heat is transfered by conduction and fluid advection. Dumps have thick partly saturated zones through which gases flow under thermal gradients and water infiltrates. Oxygen is required by the oxidation reactions and is supplied by diffusion and advection. The reaction products are carried in solution in very concentrated leachates. Numerical modeling of AMD aims to (1) provide a better understanding of the physical processes involved in AMD, (2) allow the integration of available waste rock characterization data, (3) indicate new data or studies which are required to fill the gaps in our quantitative understanding of AMD processes, and (4) supply a tool for the prediction of AMD production, taking into account the impact of control methods. These objectives can only be met through sustained research efforts. This study is part of a wider research effort which as been on-going at La Mine Doyon since 1991.

  17. Dumping and injury margins in markets with horizontal as well as vertical product differentiation

    DEFF Research Database (Denmark)

    Nielsen, Jørgen Ulff-Møller; Hansen, Jørgen Drud

    2009-01-01

    This paper examines the GATT/WTO rules for anti-dumping measures in a duopoly model with both horizontal and vertical product differentiation. The GATT/WTO rules allow for anti-dumping measures if domestic producers, exposed to price discrimination, also demonstrate injury where price...... countries in ability to implement anti-dumping measures predominantly favors the developed countries which are specialized in producing high-quality products. The paper suggests an overall critical look at the lenient rules for implementing anti-dumping measures-especially the rules for injury determination...

  18. Preliminary studies on trace element contamination in dumping sites of municipal wastes in India and Vietnam

    Science.gov (United States)

    Agusa, T.; Kunito, T.; Nakashima, E.; Minh, T. B.; Tanabe, S.; Subramanian, A.; Viet, P. H.

    2003-05-01

    The disposal of wastes in dumping sites has increasingly caused concem about adverse health effects on the populations living nearby. However, no investigation has been conducted yet on contamination in dumping sites of municipal wastes in Asian developing countries. In this study, concentrations of 11 trace elements (V, Cr, Mn, Co, Cu, Zn, Mo, Ag, Cd, Sb and Pb) were detennined in scalp hair from the population living nearby and in soil from dumping sites and control sites of India and Vietnam. Soil samples in dumping site in India showed significantly higher concentrations of some trace elements than soils in control site, whereas this trend was not notable in Vietnam. This is probably due to the fact that the wastes were covered with the soil in the dumping site of Vietnam. Cadmium concentrations in some hair samples of people living near dumping site in India and Vietnam exceeded the level associated with learning disorder in children. Levels of most of the trace elements in hair were significantly higher in dumping site than those in control site in India and Vietnam, suggesting direct or indirect exposure to those elements from dumping wastes. To our knowledge, this is the first study of trace element contamination in dumping sites in India and Vietnam.

  19. Conceptual design of dump resistor for superconducting CS of SST-1

    International Nuclear Information System (INIS)

    Roy, Swati; Pradhan, Subrata; Panchal, Arun

    2015-01-01

    During the upgradation of SST-1, the resistive central solenoid (CS) coil has been planned to be replaced with Nb 3 Sn based superconducting coil. The superconducting CS will store upto 3.5MJ of magnetic energy per operation cycle with operating current upto 14kA. In case of coil quench, the energy stored in the coils is to be extracted rapidly with a time constant of 1.5s. This will be achieved by inserting a 20m Ohm dump resistor in series with the superconducting CS which is normally shorted by circuit breakers. As a vital part of the superconducting CS quench protection system, a conceptual design of the 20m Ohm dump resistor has been proposed. In this paper, the required design aspects and a dimensional layout of the dump resistor for the new superconducting CS has been presented. Natural air circulation is proposed as cooling method for this dump resistor. The basic structure of the proposed dump resistor comprises of stainless steel grids connected in series in the shape of meander to minimize the stray inductance and increase the surface area for cooling. The entire dump resistor will be an array of such grids connected in series and parallel to meet electrical as well as thermal parameters. The maximum temperature of the proposed dump resistor is upto 350 °C during dump 3.5MJ energy. The proposed design permits indigenous fabrication of the dump resistor using commercially available welding techniques. (author)

  20. Geology beneath and beside the notorious Payatas open dump, Metro Manila, Philippines

    Science.gov (United States)

    Tomarong, C.; Arcilla, C.; de Sales, L.; Chua, S.; Garcia, E.; Pamintuan, G.

    2003-04-01

    With a minimum of 6000 tonnes/day municipal waste output, and with NO existing operational sanitary landfill and with incineration illegal, Metro Manila has a very serious solid waste disposal problem. Unsorted municipal waste are being piled in open dumps, the most notorious of which is the Payatas open dump. A recent, tragic garbage-slide in this open dump caused dozens of deaths, news of which were broadcast internationally. Political expediency laced with a lot of corruption, rather than sound science, was the main basis for selecting this site as an open dump. As an example, this dump is situated plastics. Several cross-sections cut across the dump show that the side slopes of the dump are on the average steeper than the pre-dump slopes. The “bedrock” of the Payatas dump are conglomerate members of the Pleistocene volcaniclastic Guadualupe Formation. Studies are still to be done on the extent of pollution on surface and groundwater in the Payatas environs.

  1. Scaling Criteria for the Development of an Acoustically Stabilized Dump Combustor

    National Research Council Canada - National Science Library

    Cole, Jerald A; Parr, Timothy P; Widmer, Neil C; Wilson, Kenneth J; Schadow, Klaus C; Randall, William R

    2000-01-01

    Acoustic stabilization of combustion in a dump configuration results in completion of combustion in a relatively short residence time with simultaneously low emissions of oxides of nitrogen, carbon...

  2. Radioactive waste dumping at sea: causes for concern

    International Nuclear Information System (INIS)

    Alton, D.; Atkinson, N.; Barrett, H.A.

    The dumping of various low-level radioactive wastes at sea has been carried out for many years and has been accepted as a satisfactory means of disposal by national and international regulatory authorities. There are, however, grounds for concern from an environmental standpoint which centre around two particular issues: the likely extent of mobilisation of an increasing radioactive inventory over time and the likely effects of such radioactivity if and when it should make contact with living organisms. The subject is discussed under the headings: mobilisation; effects on the marine environment; physical and biological considerations; future exploitation of the oceans (for food, minerals); and the effects of radiation. (author)

  3. Environmental assessments of sea dumped chemical warfare agents

    DEFF Research Database (Denmark)

    Sanderson, Hans; Fauser, Patrik

    This is a report on the information gathered during work related to sea dumped chemical warfare agents. It mainly reviews the work conducted in relation to the installation of the two Nord Stream gas pipeline from 2008-2012. The focus was on the weight-of-evidence risk assessment of disturbed CWA...... residues in connection with the installation of the pipelines. Novel exposure and toxicity assessments are presented and the risk is assessed. The overall conclusion is that there is a negligible acute added CWA risk towards the fish community from the installation of the pipelines....

  4. Performance with lead ions of the LHC beam dump system

    CERN Document Server

    Bruce, R; Jensen, L; Lefèvre, T; Weterings, W

    2007-01-01

    The LHC beam dump system must function safely with 208Pb82+ions. The differences with respect to the LHC proton beams are briefly recalled, and the possible areas for performance concerns discussed, in particular the various beam intercepting devices and the beam instrumentation. Energy deposition simulation results for the most critical elements are presented, and the conclusions drawn for the lead ion operation. The expected performance of the beam instrumentation systems are reviewed in the context of the damage potential of the ion beam and the required functionality of the various safety and post-operational analysis requirements.

  5. Collecting tau neutrinos near the proton dump: an outlook

    International Nuclear Information System (INIS)

    Asratyan, A.Eh.; Goritchev, P.A.; Kubantsev, M.A.

    1984-01-01

    The possibilities for the study of tan neutrino interactions in nuclear emulsion placed close to the proton dump are discussed. The processes νsub(tay)N → taysup(-)X with subsequent taysup(-) → lν tildesub(l)νsub(tay) and taysup(-) → νsub(tay) hadrons (l=μ, e) are considered. It is shown that of the approximately 1000 event surviving the kinematic selection criteria, approximately 50 leptonic and approximately 200 hadronic tay decays can be identified in emulsion

  6. Brane-worlds pseudo-Goldstinos

    International Nuclear Information System (INIS)

    Benakli, Karim; Moura, Cesar

    2008-01-01

    We consider a space-time with extra dimensions containing sectors, branes and bulk, that communicate only through gravitational interactions. In each sector, if considered separately, supersymmetry could be spontaneously broken, leading to the appearance of Goldstinos. However, when taken all together, only certain combinations of the latter states turn out to be true 'would-be-Goldstinos', eaten by the gravitinos. The other (orthogonal) combinations, we call pseudo-Goldstinos, remain in the low energy spectrum. We discuss explicitly how this happen in the simplest set-up of five-dimensional space compactified on S 1 /Z 2 . Our results divide into two parts that can be considered separately. First, we build an extension of the bulk five-dimensional supergravity, by a set of new auxiliary fields, that allows coupling it to branes where supersymmetry is spontaneously broken. Second, we discuss in details the super-Higgs mechanism in the R ξ and unitary gauges, in the presence of both of a bulk Scherk-Schwarz mechanism and brane localized F-terms. This leads us to compute the gravitino mass and provide explicit formulae for the pseudo-Goldstinos spectrum

  7. El Pseudo-Hiepes es Bernardo Polo

    Directory of Open Access Journals (Sweden)

    Jordan, William B.

    2009-12-01

    Full Text Available Nearly fifteen years ago, the author proposed the name Pseudo-Hiepes to refer to a then anonymous painter whom certain Italian art historians had called the Master of the Lombard Fruit Bowl. At the time, he argued for an Aragonese origin in the later part of the century. A signed work has finally been discovered and is published here. The artist was indeed from Zaragoza, and his name is Bernardo Polo.

    Hace unos quince años, el autor propuso el apodo Pseudo-Hiepes para identificar al pintor anónimo a quien algunos entendidos italianos habían bautizado como Maestro del Frutero lombardo. En aquel entonces, argumentó que debía tratarse de un artista aragonés, de la segunda mitad de siglo. Por fin ha aparecido una obra firmada que se presenta aquí. Efectivamente, el artista era zaragozano y su nombre es Bernardo Polo.

  8. Multipactors in klystron cavities

    International Nuclear Information System (INIS)

    Hayashi, Kazutaka; Iyeki, Hiroshi; Kikunaga, Toshiyuki.

    1993-01-01

    A multipactor phenomenon in a klystron causes gain shortage or instability problem. Some tests using a prototype klystron input cavity revealed the microwave discharges in vacuum with magnetic field. The test results and the methods to avoid multipactors are discussed in this paper. (author)

  9. What's a Cavity?

    Science.gov (United States)

    ... and deeper over time. Cavities are also called dental caries (say: KARE-eez), and if you have a ... made up mostly of the germs that cause tooth decay. The bacteria in your mouth make acids and when plaque clings to your teeth, the acids can eat away at the outermost ...

  10. Vertical cavity laser

    DEFF Research Database (Denmark)

    2016-01-01

    The present invention provides a vertical cavity laser comprising a grating layer comprising an in-plane grating, the grating layer having a first side and having a second side opposite the first side and comprising a contiguous core grating region having a grating structure, wherein an index...

  11. Oral cavity and jaw

    International Nuclear Information System (INIS)

    Solntsev, A.M.; Koval', G.Yu.

    1984-01-01

    Radioanatome of oral cavity and jaw is described. Diseases of the teeth, jaw, large salivary glands, temporo-mandibular articulation are considered. Roentgenograms of oral cacity and jaw of healthy people are presented and analyzed as well as roentgenograms in the above-mentioned diseases

  12. Niobium superconducting cavity

    CERN Multimedia

    CERN PhotoLab

    1980-01-01

    This 5-cell superconducting cavity, made from bulk-Nb, stems from the period of general studies, not all directed towards direct use at LEP. This one is dimensioned for 1.5 GHz, the frequency used at CEBAF and also studied at Saclay (LEP RF was 352.2 MHz). See also 7908227, 8007354, 8209255, 8210054, 8312339.

  13. Superconducting elliptical cavities

    CERN Document Server

    Sekutowicz, J K

    2011-01-01

    We give a brief overview of the history, state of the art, and future for elliptical superconducting cavities. Principles of the cell shape optimization, criteria for multi-cell structures design, HOM damping schemes and other features are discussed along with examples of superconducting structures for various applications.

  14. Additive Manufactured Superconducting Cavities

    Science.gov (United States)

    Holland, Eric; Rosen, Yaniv; Woolleet, Nathan; Materise, Nicholas; Voisin, Thomas; Wang, Morris; Mireles, Jorge; Carosi, Gianpaolo; Dubois, Jonathan

    Superconducting radio frequency cavities provide an ultra-low dissipative environment, which has enabled fundamental investigations in quantum mechanics, materials properties, and the search for new particles in and beyond the standard model. However, resonator designs are constrained by limitations in conventional machining techniques. For example, current through a seam is a limiting factor in performance for many waveguide cavities. Development of highly reproducible methods for metallic parts through additive manufacturing, referred to colloquially as 3D printing\\x9D, opens the possibility for novel cavity designs which cannot be implemented through conventional methods. We present preliminary investigations of superconducting cavities made through a selective laser melting process, which compacts a granular powder via a high-power laser according to a digitally defined geometry. Initial work suggests that assuming a loss model and numerically optimizing a geometry to minimize dissipation results in modest improvements in device performance. Furthermore, a subset of titanium alloys, particularly, a titanium, aluminum, vanadium alloy (Ti - 6Al - 4V) exhibits properties indicative of a high kinetic inductance material. This work is supported by LDRD 16-SI-004.

  15. Cavity Nesting Birds

    Science.gov (United States)

    Virgil E. Scott; Keith E. Evans; David R. Patton; Charles P. Stone

    1977-01-01

    Many species of cavity-nesting birds have declined because of habitat reduction. In the eastern United States, where primeval forests are gone, purple martins depend almost entirely on man-made nesting structures (Allen and Nice 1952). The hole-nesting population of peregrine falcons disappeared with the felling of the giant trees upon which they depended (Hickey and...

  16. LEP superconducting cavity

    CERN Multimedia

    1995-01-01

    Engineers work in a clean room on one of the superconducting cavities for the upgrade to the LEP accelerator, known as LEP-2. The use of superconductors allow higher electric fields to be produced so that higher beam energies can be reached.

  17. Open microwave cavities

    Czech Academy of Sciences Publication Activity Database

    Šeba, Petr; Rotter, I.; Mueller, M.; Persson, C.; Pichugin, Konstantin N.

    2001-01-01

    Roč. 9, - (2001), s. 484-487 ISSN 1386-9477 Institutional research plan: CEZ:A02/98:Z1-010-914 Keywords : microwave cavity * resonances Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.009, year: 2001

  18. Filling a Conical Cavity

    Science.gov (United States)

    Nye, Kyle; Eslam-Panah, Azar

    2016-11-01

    Root canal treatment involves the removal of infected tissue inside the tooth's canal system and filling the space with a dense sealing agent to prevent further infection. A good root canal treatment happens when the canals are filled homogeneously and tightly down to the root apex. Such a tooth is able to provide valuable service for an entire lifetime. However, there are some examples of poorly performed root canals where the anterior and posterior routes are not filled completely. Small packets of air can be trapped in narrow access cavities when restoring with resin composites. Such teeth can cause trouble even after many years and lead the conditions like acute bone infection or abscesses. In this study, the filling of dead-end conical cavities with various liquids is reported. The first case studies included conical cavity models with different angles and lengths to visualize the filling process. In this investigation, the rate and completeness at which a variety of liquids fill the cavity were observed to find ideal conditions for the process. Then, a 3D printed model of the scaled representation of a molar with prepared post spaces was used to simulate the root canal treatment. The results of this study can be used to gain a better understanding of the restoration for endodontically treated teeth.

  19. Examples of pseudo-bosons in quantum mechanics

    International Nuclear Information System (INIS)

    Bagarello, F.

    2010-01-01

    We discuss two physical examples of the so-called pseudo-bosons, recently introduced in connection with pseudo-hermitian quantum mechanics. In particular, we show that the so-called extended harmonic oscillator and the Swanson model satisfy all the assumptions of the pseudo-bosonic framework introduced by the author. We also prove that the biorthogonal bases they produce are not Riesz bases.

  20. Lattice Boltzmann simulation of immiscible displacement in the cavity with different channel configurations

    Science.gov (United States)

    Lou, Qin; Zang, Chenqiang; Yang, Mo; Xu, Hongtao

    In this work, the immiscible displacement in a cavity with different channel configurations is studied using an improved pseudo-potential lattice Boltzmann equation (LBE) model. This model overcomes the drawback of the dependence of the fluid properties on the grid size, which exists in the original pseudo-potential LBE model. The approach is first validated by the Laplace law. Then, it is employed to study the immiscible displacement process. The influences of different factors, such as the surface wettability, the distance between the gas cavity and liquid cavity and the surface roughness of the channel are investigated. Numerical results show that the displacement efficiency increases and the displacement time decreases with the increase of the surface contact angle. On the other hand, the displacement efficiency increases with increasing distance between the gas cavity and the liquid cavity at first and finally reaches a constant value. As for the surface roughness, two structures (a semicircular cavity and a semicircular bulge) are studied. The comprehensive results show that although the displacement processes for both the structures depend on the surface wettability, they present quite different behaviors. Specially, for the roughness structure constituted by the semicircular cavity, the displacement efficiency decreases and displacement time increases evidently with the size of the semicircular cavity for the small contact angle. The trend slows down as the increase of the contact angle. Once the contact angle exceeds a certain value, the size of the semicircular cavity almost has no influence on the displacement process. While for the roughness structure of a semicircular bulge, the displacement efficiency increases with the size of bulge first and then it decreases for the small contact angle. The displacement efficiency increases first and finally reaches a constant for the large contact angle. The results also show that the displacement time has an

  1. Scaphoid pseudo-arthrosis: Frequency, pathogenesis and course

    Energy Technology Data Exchange (ETDEWEB)

    Schunk, K.; Teifke, A.; Benning, R.; Dahm, M.; Thelen, R.; Schild, H.

    1989-06-01

    Eighty-three scaphoid pseudo-arthroses were found amongst 1.104 scaphoid examinations. Sixtyseven were present at the first examination and 16 pseudo-arthroses developed amongst 252 scaphoid fractures. Men were affected predominantly, particularly in the 20 to 40-year old group. Fractures in the proximal third of the scaphoid and vertical oblique fractures had a particular tendency to pseudo-arthrosis formation. The operative treatment of choice is a Matti-Russe bone graft. Only one patient in seven with definite scaphoid pseudo-arthrosis showed firm fusion. (orig.).

  2. Scaphoid pseudo-arthrosis: Frequency, pathogenesis and course

    International Nuclear Information System (INIS)

    Schunk, K.; Teifke, A.; Benning, R.; Dahm, M.; Thelen, R.; Schild, H.; Mainz Univ.

    1989-01-01

    Eighty-three scaphoid pseudo-arthroses were found amongst 1.104 scaphoid examinations. Sixtyseven were present at the first examination and 16 pseudo-arthroses developed amongst 252 scaphoid fractures. Men were affected predominantly, particularly in the 20 to 40-year old group. Fractures in the proximal third of the scaphoid and vertical oblique fractures had a particular tendency to pseudo-arthrosis formation. The operative treatment of choice is a Matti-Russe bone graft. Only one patient in seven with definite scaphoid pseudo-arthrosis showed firm fusion. (orig.) [de

  3. Implosion of the small cavity and large cavity cannonball targets

    International Nuclear Information System (INIS)

    Nishihara, Katsunobu; Yamanaka, Chiyoe.

    1984-01-01

    Recent results of cannonball target implosion research are briefly reviewed with theoretical predictions for GEKKO XII experiments. The cannonball targets are classified into two types according to the cavity size ; small cavity and large cavity. The compression mechanisms of the two types are discussed. (author)

  4. Conceptual Design of the Linac4 Main Dump

    CERN Document Server

    Leitao, I V; Maglioni, C

    2012-01-01

    Linac4 is the new CERN linear accelerator intended to replace the ageing Linac2 as the injector to the Proton Synchrotron Booster (PSB) for increasing the luminosity of the Large Hadron Collider (LHC). By delivering a 160MeV H- beam, Linac4 will provide the necessary conditions to double the brightness and intensity of the beam extracted from the PSB. This paper describes the conceptual design of the Linac4 Main Dump, where two different concepts relying respectively on water and air cooling were compared and evaluated. Based on the application of analytical models for the energy deposited by the beam, heat conduction and cooling concepts, a parametric study was performed. This approach allowed the identification of the “optimal” configuration for these two conceptual geometries and their relative comparison. Besides giving the theoretical guidelines for the design of the new dump, this work also contributes to the development of analytical tools to allow a better understanding of the influence of the se...

  5. Performance Studies for Protection Against Asynchronous Dumps in the LHC

    CERN Document Server

    Kramer, T; Bracco, C; Goddard, B; Meddahi, M

    2010-01-01

    The LHC beam dump system has to safely dispose all beams in a wide energy range of 450 GeV to 7 TeV. A 3 ms abort gap in the beam structure for the switch-on of the extraction kicker field ideally allows a loss-free extraction under normal operating conditions. However, a low number of asynchronous beam aborts is to be expected from reliability calculations and from the first year's operational experience with the beam dump kickers. For such cases, MAD-X simulations including all optics and alignment errors have been performed to determine loss patterns around the LHC as a function of the position of the main protection elements in interaction region six. Special attention was paid to the beam load on the tungsten collimators which protect the triplets in the LHC experimental insertions, and the tracking results compared with semi-analytical numerical estimates. The simulations are also compared to the results of beam commissioning of these protection devices.

  6. Pointwise estimates of pseudo-differential operators

    DEFF Research Database (Denmark)

    Johnsen, Jon

    As a new technique it is shown how general pseudo-differential operators can be estimated at arbitrary points in Euclidean space when acting on functions u with compact spectra.The estimate is a factorisation inequality, in which one factor is the Peetre–Fefferman–Stein maximal function of u......, whilst the other is a symbol factor carrying the whole information on the symbol. The symbol factor is estimated in terms of the spectral radius of u, so that the framework is well suited for Littlewood–Paley analysis. It is also shown how it gives easy access to results on polynomial bounds...... and estimates in Lp , including a new result for type 1,1-operators that they are always bounded on Lp -functions with compact spectra....

  7. Pointwise estimates of pseudo-differential operators

    DEFF Research Database (Denmark)

    Johnsen, Jon

    2011-01-01

    As a new technique it is shown how general pseudo-differential operators can be estimated at arbitrary points in Euclidean space when acting on functions u with compact spectra. The estimate is a factorisation inequality, in which one factor is the Peetre–Fefferman–Stein maximal function of u......, whilst the other is a symbol factor carrying the whole information on the symbol. The symbol factor is estimated in terms of the spectral radius of u, so that the framework is well suited for Littlewood–Paley analysis. It is also shown how it gives easy access to results on polynomial bounds...... and estimates in Lp, including a new result for type 1, 1-operators that they are always bounded on Lp-functions with compact spectra....

  8. Pseudo-Observables in Higgs decays

    CERN Multimedia

    CERN. Geneva

    2015-01-01

    In view of future high-statistics data, it is useful to define a framework for precise determinations of the properties of the Higgs particle valid in generic extensions of the Standard Model. For Higgs decays, this goal can be achieved with a limited set of "Pseudo-Observables" (PO). The PO provides a systematic generalization of the "kappa-framework" so far adopted by the LHC experiments and provide a useful bridge between data and theory predictions. I discuss how the PO are defined, with particular attention to the h->4f decays, and how they can be used to test various dynamical and symmetry hypotheses about the Higgs sector. The relation between PO and EFT couplings is also discussed.

  9. Fast crab cavity failures in HL-LHC

    CERN Document Server

    Yee-Rendon, B; Calaga, R; Tomas, R; Zimmermann, F; Barranco, J

    2014-01-01

    Crab cavities (CCs) are a key ingredient of the High-Luminosity Large Hadron Collider (HL-LHC) to ensure head on collisions at the main experiments (ATLAS and CMS) and fully profit from the smaller provided by the ATS optics [1]. At KEKB, CCs have exhibited abrupt changes of phase and voltage during a time period of few LHC turns and considering the large energy stored in the HL-LHC beam, CC failures represent a serious risk to the LHC machine protection. In this paper, we discuss the effect of CC voltage or phase changes on a time interval similar to, or longer than, the one needed to dump the beam. The simulations assume a realistic steady-state distribution to assess the beam losses for the HL-LHC. Additionally, some strategies are studied in order to reduce the damage caused by the CC failures.

  10. Long period pseudo random number sequence generator

    Science.gov (United States)

    Wang, Charles C. (Inventor)

    1989-01-01

    A circuit for generating a sequence of pseudo random numbers, (A sub K). There is an exponentiator in GF(2 sup m) for the normal basis representation of elements in a finite field GF(2 sup m) each represented by m binary digits and having two inputs and an output from which the sequence (A sub K). Of pseudo random numbers is taken. One of the two inputs is connected to receive the outputs (E sub K) of maximal length shift register of n stages. There is a switch having a pair of inputs and an output. The switch outputs is connected to the other of the two inputs of the exponentiator. One of the switch inputs is connected for initially receiving a primitive element (A sub O) in GF(2 sup m). Finally, there is a delay circuit having an input and an output. The delay circuit output is connected to the other of the switch inputs and the delay circuit input is connected to the output of the exponentiator. Whereby after the exponentiator initially receives the primitive element (A sub O) in GF(2 sup m) through the switch, the switch can be switched to cause the exponentiator to receive as its input a delayed output A(K-1) from the exponentiator thereby generating (A sub K) continuously at the output of the exponentiator. The exponentiator in GF(2 sup m) is novel and comprises a cyclic-shift circuit; a Massey-Omura multiplier; and, a control logic circuit all operably connected together to perform the function U(sub i) = 92(sup i) (for n(sub i) = 1 or 1 (for n(subi) = 0).

  11. Hollow waveguide cavity ringdown spectroscopy

    Science.gov (United States)

    Dreyer, Chris (Inventor); Mungas, Greg S. (Inventor)

    2012-01-01

    Laser light is confined in a hollow waveguide between two highly reflective mirrors. This waveguide cavity is used to conduct Cavity Ringdown Absorption Spectroscopy of loss mechanisms in the cavity including absorption or scattering by gases, liquid, solids, and/or optical elements.

  12. Optimization of photonic crystal cavities

    DEFF Research Database (Denmark)

    Wang, Fengwen; Sigmund, Ole

    2017-01-01

    We present optimization of photonic crystal cavities. The optimization problem is formulated to maximize the Purcell factor of a photonic crystal cavity. Both topology optimization and air-hole-based shape optimization are utilized for the design process. Numerical results demonstrate...... that the Purcell factor of the photonic crystal cavity can be significantly improved through optimization....

  13. Nuclear reactor cavity streaming shield

    International Nuclear Information System (INIS)

    Klotz, R.J.; Stephen, D.W.

    1978-01-01

    The upper portion of a nuclear reactor vessel supported in a concrete reactor cavity has a structure mounted below the top of the vessel between the outer vessel wall and the reactor cavity wall which contains hydrogenous material which will attenuate radiation streaming upward between vessel and the reactor cavity wall while preventing pressure buildup during a loss of coolant accident

  14. Changes in some physical properties of soils in the chronosequence of self-overgrown dumps of the Sokolov quarry-dump complex, Czechia

    Czech Academy of Sciences Publication Activity Database

    Kuráž, V.; Frouz, Jan; Kuráž, M.; Mako, A.; Šustr, Vladimír; Cejpek, J.; Romanov, O.V.; Abakumov, E.V.

    2012-01-01

    Roč. 45, č. 3 (2012), s. 266-272 ISSN 1064-2293 R&D Projects: GA MŠk 2B08023 Grant - others:Russian Foundation for Basic Research(RU) 08-04-01128 Institutional support: RVO:60077344 Keywords : physical properties of soil s * chronosequence of self-overgrown dumps * Sokolov quarry-dump complex Subject RIV: EH - Ecology, Behaviour Impact factor: 0.216, year: 2012

  15. Research on tractive power of KZC-5 rear dump truck in underground mine

    International Nuclear Information System (INIS)

    Lei Zeyong

    2003-01-01

    The tractive power of KZC-5 rear dump truck in underground mine is studied in this paper. The principles and ways of defining the power are discussed. It is proved that the power of KZC-5 rear dump truck in underground mine is reasonable in the industrial scale test

  16. Environmental impact and recovery at two dumping sites for dredged material in the North Sea

    International Nuclear Information System (INIS)

    Stronkhorst, J.; Ariese, F.; Hattum, B. van; Postma, J.F.; Kluijver, M. de; Besten, P.J. den; Bergman, M.J.N.; Daan, R.; Murk, A.J.; Vethaak, A.D.

    2003-01-01

    Marine benthic resources near dumping sites are adversely affected by physical disturbances, but a causal link to contaminant damage could not be found. - The environmental impact and recovery associated with the long and uninterrupted disposal of large volumes of moderately contaminated dredged material from the port of Rotterdam was studied at nearby dumping sites in the North Sea. Observations were made on sediment contamination, ecotoxicity, biomarker responses and benthic community changes shortly after dumping at the 'North' site had ceased and at the start of disposal at the new dumping site 'Northwest'. During the period of dumping, very few benthic invertebrates were found at the North site. Concentrations of cadmium, mercury, polychlorinated biphenyls (PCBs), polyaromatic hydrocarbons (PAHs) and tributyltin (TBT) in the fine sediment fraction ( 3 of moderately contaminated dredged material had been dumped at the new dumping site Northwest, the species richness and abundance of benthic invertebrates declined over an area extending about 1-2 km eastwards. This correlated with a shift in sediment texture from sand to silt. The contamination of the fine sediment fraction at the Northwest location doubled. It is concluded that marine benthic resources at and around the dumping sites have been adversely affected by physical disturbance (burial, smothering). However, no causal link could be established with sediment-associated contaminants from the dredged spoils

  17. Regularities of restoration of plant cover on the dumps of the Kuznetsk Basin

    Directory of Open Access Journals (Sweden)

    A. N. Kupriyanov

    2016-04-01

    Full Text Available The article considers the issues of the restoration vegetation on the dumps of the coal enterprises of the Kuznetsk Basin. Studies have shown that the dumps have a wide range of environmental conditions and are potentially suitable for establishment of plants. To negative environmental factors at the mine dumps include the lack of productive moisture, failed penetration, contrasting temperature regime on the different elements of the relief, and low potential fertility of the embryonic soils. Positive – high humidity in the depressions, the high content of fine-grained deposits in the lower part of the elephant dumps, excessive accumulation of snow in the winter on separate dumping sites. On disturbed lands identified eight technogenic ecotopes, characterized by various microrelief, moisture level, amount of fine fractions of technogenic eluvium determining favorable, moderately favorable and unfavorable conditions for vegetation of disturbed land. Selected three stages of syngenesis: pioneer stage, simple plant communities and complex plant communities. The stage of zonal phytocenosis on the dumps was not detected. The basis of diagnostic signs consists of the projective cover, the nature of the host plants, the number of species part of the zonal species. The selected criteria are universal and can be applicable to most dumps. Speed of syngenetic succession does not depend on calendar age of the dumps, and environmental conditions, which are formed on separate sites.

  18. Obese patients with type 2 diabetes submitted to banded gastric bypass: greater incidence of dumping syndrome.

    Science.gov (United States)

    Padoin, Alexandre Vontobel; Galvão Neto, Manoel; Moretto, Myriam; Barancelli, Fabiano; Schroer, Caroline Eckerdt; Mottin, Cláudio Corá

    2009-11-01

    Dumping syndrome is one of ten most common complications in morbidly obese patients operated. Recent studies in relation to type 2 diabetes mellitus (DM2) in patients submitted to gastric bypass led us to examine the different outcomes in this group of patients. Our objective was to determine the difference in the prevalence of dumping syndrome in patients with DM2 submitted to gastric bypass. In this retrospective study, 49 diabetic and 54 non-diabetic morbidly obese patients were submitted to gastric bypass and followed up at 3, 6, and 12 months after surgery. The occurrence of dumping was determined by the patient's medical chart, where it was considered positive if recorded in at least one of three evaluations. The 103 patients evaluated had a mean BMI of 49.5 +/- 9.3 kg/m(2) and mean age of 38 +/- 9.7 years, with 75.7% being women. The prevalence of dumping syndrome in this population was 24.3%. The prevalence of dumping was greater in patients with DM2 (44.9%) when compared to the control group (5.6%; p DM2 as the only variable associated with dumping syndrome. Dumping syndrome is a common postoperative complication in gastric bypass. Patients with DM2 show a greater postoperative prevalence of dumping.

  19. Radiation monitoring and beam dump system of the OPAL silicon microvertex detector

    CERN Document Server

    Braibant, S

    1997-01-01

    The OPAL microvertex silicon detector radiation monitoring and beam dump system is described. This system was designed and implemented in order to measure the radiation dose received at every beam crossing and to induce a fast beam dump if the radiation dose exceeds a given threshold.

  20. The Impact of Refuse Dump sites on the Physico-chemical and ...

    African Journals Online (AJOL)

    The Impact of Refuse Dump sites on the Physico-chemical and Microbial Properties of ground Water in some selected areas. ... Journal of Agricultural Research and Development. Journal Home ... The pollution effect of refuse dumps on the quality of wells at Ojota, Lagos, Apete, Ibadan and Odopetu, Akure were studied.

  1. Soil contamination by brominated flame retardants in open waste dumping sites in Asian developing countries.

    Science.gov (United States)

    Eguchi, Akifimi; Isobe, Tomohiko; Ramu, Karri; Tue, Nguyen Minh; Sudaryanto, Agus; Devanathan, Gnanasekaran; Viet, Pham Hung; Tana, Rouch Seang; Takahashi, Shin; Subramanian, Annamalai; Tanabe, Shinsuke

    2013-03-01

    In Asian developing countries, large amounts of municipal wastes are dumped into open dumping sites each day without adequate management. This practice may cause several adverse environmental consequences and increase health risks to local communities. These dumping sites are contaminated with many chemicals including brominated flame retardants (BFRs) such as polybrominated diphenyl ethers (PBDEs) and hexabromocyclododecanes (HBCDs). BFRs may be released into the environment through production processes and through the disposal of plastics and electronic wastes that contain them. The purpose of this study was to elucidate the status of BFR pollution in municipal waste dumping sites in Asian developing countries. Soil samples were collected from six open waste dumping sites and five reference sites in Cambodia, India, Indonesia, Malaysia, and Vietnam from 1999 to 2007. The results suggest that PBDEs are the dominant contaminants in the dumping sites in Asian developing countries, whereas HBCD contamination remains low. Concentrations of PBDEs and HBCDs ranged from ND to 180 μg/kg dry wt and ND to 1.4 μg/kg dry wt, respectively, in the reference sites and from 0.20 to 430 μg/kg dry wt and ND to 2.5 μg/kg dry wt, respectively, in the dumping sites. Contamination levels of PBDEs in Asian municipal dumping sites were comparable with those reported from electronic waste dismantling areas in Pearl River delta, China. Copyright © 2012 Elsevier Ltd. All rights reserved.

  2. Acute toxicity of sea-dumped chemical munitions: Luminating the environmental toxicity of legacy compounds

    DEFF Research Database (Denmark)

    Mohammed Abdullah Christensen, Ilias; Sanderson, Hans; Baatrup, Erik

    2016-01-01

    As a result of the disarmament of Germany after the Second World War, 65,000 tons of chemical munitions were dumped in the Baltic Sea. Approximately 13,000 tons containing chemical warfare agents (CWAs) of which 11,000 tons were dumped in the Bornholm Basin east of Bornholm. This paper addresses...

  3. Københavns Kommunes indsats mod social dumping - målopfyldelsesevaluering

    DEFF Research Database (Denmark)

    Jørgensen, Henning; Baadsgaard, Kelvin

    2017-01-01

    Evaluering af indsatsen i Københavns Kommune for at imødegå social dumping ved hjælp af målopfyldelses-model......Evaluering af indsatsen i Københavns Kommune for at imødegå social dumping ved hjælp af målopfyldelses-model...

  4. The mathematical model of vertical solt transfer on mine dumps Western Donbass

    Directory of Open Access Journals (Sweden)

    H. P. Yevhrashkina,

    2011-11-01

    Full Text Available On the based theory of physical-chemical hydrodynamics of porous media offer a range of mathematical models of vertical salt transfer on mine dumps Western Donbass. designed several variants of dumps free overgrowth for the optimal performance for transpiration of wild plants.

  5. Environmental impact of differently remediated hard coal overburden and tailings dumps a few decades after remediation

    International Nuclear Information System (INIS)

    Willscher, S.; Felix, M.; Sohr, A.

    2010-01-01

    Coal mining in the Saxony region of Germany has caused heavy metal and arsenic pollution in adjacent groundwater and surface waters. Coal waste dumping sites are leaching heavy metals and metalloids in the form of fine precipitates into local rivers. This paper studied the different remediation strategies used at 3 different dump sites in the area. The aim of the study was to determine the environmental impact of the dumps and evaluate the long-term effects of remediation measures. The dumps consisted of coarse to fine-grained materials from former processing activities, and contained pyrite in varying concentrations. Samples from different depth as well as groundwater samples were taken from the sites and investigated for their mechanical, geological, geochemical, biogeochemical, and physico-chemical characteristics. Seepage formation rates and contaminant loads at the dump sites were compared. The study showed that the revegetation of dump surfaces can help to prevent against erosion, but cannot prevent acid mine drainage (AMD) generation. The additional seals and covers placed at 2 of the dumps resulted in a high reduction of seepage waters, and almost no acidification of dump materials. 5 refs., 1 fig.

  6. EXPERIMENTAL RESEARCH OF PROCESSING OF DUMP SAND-CLAY MIXES BY THE CENTRIFUGAL AND SHOCK CRUSHING

    Directory of Open Access Journals (Sweden)

    V. V. Vorobev

    2015-01-01

    Full Text Available Results of experimental research of processing of centrifugal and shock crushing of dump sandy-clay mixes are given. Use of products of processing of received mixes in foundry production and in production of asphalt concrete mixes allows to exclude transportation of the mix to dumping.

  7. Inflammatory pseudo tumor (pseudo sarcoma) of the urinary bladder: clinical aspects and computed tomography images

    International Nuclear Information System (INIS)

    Romero, A.; Bueno, A.; Trigo, J.E.; Torres, A.

    1998-01-01

    Inflammatory pseudo tumor (pseudosarcoma) of the urinary bladder is an uncommon lesion with benign histopathological features. It consists of large cell proliferation, spindle-cell morphology (myofibroblasts) deriving from the bladder sub mucosa. It can present in patients of either sex and of any age; on occasion, it has been related to a history of surgery or previous bladder injury. Both the clinical and radiological features are nonspecific in that they do not differentiate this lesion from malignant disease; its diagnosis can only be definitively established by histopathological study. We present a case of inflammatory bladder pseudo tumor in a young girl, describing the clinical and radiological features of this lesion, which only rarely has been dealt with in the literature, particularly that concerning radiology. (Author) 13 refs

  8. Colloquium: cavity optomechanics

    CERN Multimedia

    2011-01-01

    Monday 14 November 2011, 17:00 Ecole de Physique, Auditoire Stueckelberg Université de Genève Cavity optomechanics: controlling micro mechanical oscillators with laser light Prof. Tobias Kippenberg EPFL, Lausanne Laser light can be used to cool and to control trapped ions, atoms and molecules at the quantum level. This has lead to spectacular advances such as the most precise atomic clocks. An outstanding frontier is the control with lasers of nano- and micro-mechancial systems. Recent advances in cavity optomechanics have allowed such elementary control for the first time, enabling mechanical systems to be ground state cooled leading to readout with quantum limited sensitivity and permitting to explore new device concepts resulting from radiation pressure.  

  9. Leaching materials from cavities

    International Nuclear Information System (INIS)

    Hodgson, T.D.; Jordan, T.W.J.

    1980-01-01

    A material is leached from a cavity by contacting the material with a liquid and subjecting the liquid to a number of pressure cycles, each pressure cycle involving a decrease in pressure to cause boiling of the liquid, followed by a rise in pressure to inhibit the boiling. The method may include the step of heating the liquid to a temperature near to its boiling point. The material may be nuclear fuel pellets or calcium carbonate pellets. (author)

  10. Superconducting cavities for HERA

    International Nuclear Information System (INIS)

    Dwersteg, B.; Ebeling, W.; Moeller, W.D.; Renken, D.; Proch, D.; Sekutowicz, J.; Susta, J.; Tong, D.

    1988-01-01

    Superconducting 500 MHz cavities are developed to demonstrate the feasibility of upgrading the e-beam energy of the HERA storage ring. A prototype module with 2 x 4 cell resonators and appropriate fundamental and higher mode couplers has been designed at DESY and is being built by industrial firms. The design and results of RF and cryogenic measurements are reported in detail. 17 references, 10 figures, 2 tables

  11. RF generation in the DARHT Axis-II beam dump

    Energy Technology Data Exchange (ETDEWEB)

    Ekdahl, Carl A. Jr. [Los Alamos National Laboratory

    2012-05-03

    We have occasionally observed radio-frequency (RF) electromagnetic signals in the downstream transport (DST) of the second axis linear induction accelerator (LIA) at the dual-axis radiographic hydrodynamic testing (DARHT) facility. We have identified and eliminated some of the sources by eliminating the offending cavities. However, we still observe strong RF in the range 1 GHz t0 2 GHz occurring late in the {approx}2-{micro}s pulse that can be excited or prevented by varying the downstream tune. The narrow frequency width (<0.5%) and near exponential growth at the dominant frequency is indicative of a beam-cavity interaction, and electro-magnetic simulations of cavity structure show a spectrum rich in resonances in the observed frequency range. However, the source of beam produced RF in the cavity resonance frequency range has not been identified, and it has been the subject of much speculation, ranging from beam-plasma or beam-ion instabilities to unstable cavity coupling.

  12. Efficiency of Low-Profile External Dumping at Open Pit Coal Mining in Kemerovo Region

    Science.gov (United States)

    Selyukov, Alexey; Ermolaev, Vyacheslav; Kostinez, Irina

    2017-11-01

    Kemerovo region is one of the largest industrial regions of Russia, with a raw material specialization. The rapid growth of the coal industry in recent years has been greatly facilitated by the expansion and development of open pit mining for coal seams extraction, accompanied by an increase in the volumes of overburden and the height of the dumps. There are about 400 objects in the Russian Federation Government Register of Waste Disposal Facilities 80% of which are dumps. Approaches both to external dumping and to the technical stage of reclamation currently contribute to the growth of geomorphic system's instability. Thus, it is proposed to slightly change the approaches to external dumping: the essence consists in the formation of an external dump of overburden, which in future would represent a favorable landscape unit of a flat surface relief used for subsequent differently directed purposes.

  13. Efficiency of Low-Profile External Dumping at Open Pit Coal Mining in Kemerovo Region

    Directory of Open Access Journals (Sweden)

    Selyukov Alexey

    2017-01-01

    Full Text Available Kemerovo region is one of the largest industrial regions of Russia, with a raw material specialization. The rapid growth of the coal industry in recent years has been greatly facilitated by the expansion and development of open pit mining for coal seams extraction, accompanied by an increase in the volumes of overburden and the height of the dumps. There are about 400 objects in the Russian Federation Government Register of Waste Disposal Facilities 80% of which are dumps. Approaches both to external dumping and to the technical stage of reclamation currently contribute to the growth of geomorphic system's instability. Thus, it is proposed to slightly change the approaches to external dumping: the essence consists in the formation of an external dump of overburden, which in future would represent a favorable landscape unit of a flat surface relief used for subsequent differently directed purposes.

  14. Energy deposition profile for modification proposal of ISOLDE’s HRS Beam Dump, from FLUKA simulations

    CERN Document Server

    Vlachoudis, V

    2014-01-01

    The current ISOLDE HRS beam dump has been found to be unsuitable on previous simulations, due to thermomechanical stresses. In this paper a proposal for modifying HRS dump is studied using FLUKA. The energy deposited in this modified beam dump and the amount of neutrons streaming to the tunnel area are scored and compared with the simulation of current dump. Two versions of the modification have been assessed, determining which of them is more desirable in terms of influence of radiation on ISOLDE’s tunnel. Finally, a rough estimate of temperature raise in the modified dump is shown. Further conclusions on the adequacy of these modifications need to include the thermomechanical calculations’ results, based on those presented here.

  15. Characterizing cavities in model inclusion molecules: a comparative study.

    Science.gov (United States)

    Torrens, F; Sánchez-Marín, J; Nebot-Gil, I

    1998-04-01

    We have selected fullerene-60 and -70 cavities as model systems in order to test several methods for characterizing inclusion molecules. The methods are based on different technical foundations such as a square and triangular tessellation of the molecule taken as a unitary sphere, spherical tessellation of the molecular surface, numerical integration of the atomic volumes and surfaces, triangular tessellation of the molecular surface, and a cubic lattice approach to a molecular space. Accurate measures of the molecular volume and surface area have been performed with the pseudo-random Monte Carlo (MCVS) and uniform Monte Carlo (UMCVS) methods. These calculations serve as a reference for the rest of the methods. The SURMO2 and MS methods have not recognized the cavities and may not be convenient for intercalation compounds. The programs that have detected the cavities never exceed 5% deviation relative to the reference values for molecular volume and surface area. The GEPOL algorithm, alone or combined with TOPO, shows results in good agreement with those of the UMCVS reference. The uniform random number generator provides the fastest convergence for UMCVS and a correct estimate of the standard deviations. The effect of the internal cavity on the accessible surfaces has been calculated.

  16. Generating pseudo test collections for learning to rank scientific articles

    NARCIS (Netherlands)

    Berendsen, R.; Tsagkias, M.; de Rijke, M.; Meij, E.

    2012-01-01

    Pseudo test collections are automatically generated to provide training material for learning to rank methods. We propose a method for generating pseudo test collections in the domain of digital libraries, where data is relatively sparse, but comes with rich annotations. Our intuition is that

  17. Regression analysis of censored data using pseudo-observations

    DEFF Research Database (Denmark)

    Overgaard, Morten; Andersen, Per K.; Parner, Erik T.

    2015-01-01

    competing risks, the restricted mean survival-time function, and the causespecific lost-lifetime function. The pseudo-observations can be used to assess the effects of covariates on their respective functions at different times by fitting generalized linear models to the pseudo-observations. The updated...

  18. Pseudo-classical theory of Majorana-Weyl particle

    International Nuclear Information System (INIS)

    Grigoryan, G.V.; Grigoryan, R.P.; Tyutin, I.V.

    1996-01-01

    A pseudo-classical theory of Weyl particle in the space-time dimensions D = 2 n is constructed. The canonical quantization of that pseudo-classical theory is carried out and it results in the theory of the D = 2 n dimensional Weyl particle in the Foldy-Wouthuysen representation. 28 refs

  19. Higher-order Jordan Osserman pseudo-Riemannian manifolds

    International Nuclear Information System (INIS)

    Gilkey, Peter B; Ivanova, Raina; Zhang Tan

    2002-01-01

    We study the higher-order Jacobi operator in pseudo-Riemannian geometry. We exhibit a family of manifolds so that this operator has constant Jordan normal form on the Grassmannian of subspaces of signature (r, s) for certain values of (r, s). These pseudo-Riemannian manifolds are new and non-trivial examples of higher-order Osserman manifolds

  20. Higher-order Jordan Osserman pseudo-Riemannian manifolds

    Energy Technology Data Exchange (ETDEWEB)

    Gilkey, Peter B [Mathematics Department, University of Oregon, Eugene, OR 97403 (United States); Ivanova, Raina [Mathematics Department, University of Hawaii - Hilo, 200 W Kawili St, Hilo, HI 96720 (United States); Zhang Tan [Department of Mathematics and Statistics, Murray State University, Murray, KY 42071 (United States)

    2002-09-07

    We study the higher-order Jacobi operator in pseudo-Riemannian geometry. We exhibit a family of manifolds so that this operator has constant Jordan normal form on the Grassmannian of subspaces of signature (r, s) for certain values of (r, s). These pseudo-Riemannian manifolds are new and non-trivial examples of higher-order Osserman manifolds.

  1. Degeneracy of energy levels of pseudo-Gaussian oscillators

    International Nuclear Information System (INIS)

    Iacob, Theodor-Felix; Iacob, Felix; Lute, Marina

    2015-01-01

    We study the main features of the isotropic radial pseudo-Gaussian oscillators spectral properties. This study is made upon the energy levels degeneracy with respect to orbital angular momentum quantum number. In a previous work [6] we have shown that the pseudo-Gaussian oscillators belong to the class of quasi-exactly solvable models and an exact solution has been found

  2. A note on Lorentz transformation and pseudo-rapidity distributions

    International Nuclear Information System (INIS)

    Hama, Y.

    1980-07-01

    It is shown that although rapidity and pseudo-rapidity are almost equivalent variables, their difference may in pratice become quite remarkable. Non Lorentz invariance of pseudo-rapidity distributions may cause appearance of strange effects at first sight, such as deformation of a perfectly symmetric particle distribution into an asymmetric one when going to another frame. (Author) [pt

  3. Theory of pseudo-differential operators over C*-Algebras

    International Nuclear Information System (INIS)

    Mohammad, N.

    1987-06-01

    In this article the behaviour of adjoints and composition of pseudo-differential operators in the framework of a C*-algebra is studied. It results that the class of pseudo-differential operators of order zero is a C*-algebra. 8 refs

  4. Pseudo-affinity chromatography of rumen microbial cellulase on ...

    African Journals Online (AJOL)

    Pseudo-affinity chromatography of rumen microbial cellulase on Sepharose- Cibacron Blue F3GA. ... African Journal of Biotechnology ... Pseudo affinity adsorption of bioproducts on Sepharose-cibacron blue F3-GA was subjected to rumen microbial enzyme evaluation through batch binding and column chromatography of ...

  5. Generalized Heisenberg algebra and (non linear) pseudo-bosons

    Science.gov (United States)

    Bagarello, F.; Curado, E. M. F.; Gazeau, J. P.

    2018-04-01

    We propose a deformed version of the generalized Heisenberg algebra by using techniques borrowed from the theory of pseudo-bosons. In particular, this analysis is relevant when non self-adjoint Hamiltonians are needed to describe a given physical system. We also discuss relations with nonlinear pseudo-bosons. Several examples are discussed.

  6. Pseudo-populations a basic concept in statistical surveys

    CERN Document Server

    Quatember, Andreas

    2015-01-01

    This book emphasizes that artificial or pseudo-populations play an important role in statistical surveys from finite universes in two manners: firstly, the concept of pseudo-populations may substantially improve users’ understanding of various aspects in the sampling theory and survey methodology; an example of this scenario is the Horvitz-Thompson estimator. Secondly, statistical procedures exist in which pseudo-populations actually have to be generated. An example of such a scenario can be found in simulation studies in the field of survey sampling, where close-to-reality pseudo-populations are generated from known sample and population data to form the basis for the simulation process. The chapters focus on estimation methods, sampling techniques, nonresponse, questioning designs and statistical disclosure control.This book is a valuable reference in understanding the importance of the pseudo-population concept and applying it in teaching and research.

  7. Crab cavities for linear colliders

    CERN Document Server

    Burt, G; Carter, R; Dexter, A; Tahir, I; Beard, C; Dykes, M; Goudket, P; Kalinin, A; Ma, L; McIntosh, P; Shulte, D; Jones, Roger M; Bellantoni, L; Chase, B; Church, M; Khabouline, T; Latina, A; Adolphsen, C; Li, Z; Seryi, Andrei; Xiao, L

    2008-01-01

    Crab cavities have been proposed for a wide number of accelerators and interest in crab cavities has recently increased after the successful operation of a pair of crab cavities in KEK-B. In particular crab cavities are required for both the ILC and CLIC linear colliders for bunch alignment. Consideration of bunch structure and size constraints favour a 3.9 GHz superconducting, multi-cell cavity as the solution for ILC, whilst bunch structure and beam-loading considerations suggest an X-band copper travelling wave structure for CLIC. These two cavity solutions are very different in design but share complex design issues. Phase stabilisation, beam loading, wakefields and mode damping are fundamental issues for these crab cavities. Requirements and potential design solutions will be discussed for both colliders.

  8. New limits on hidden photons from past electron beam dumps

    International Nuclear Information System (INIS)

    Andreas, Sarah; Niebuhr, Carsten; Ringwald, Andreas

    2012-09-01

    Hidden sectors with light extra U(1) gauge bosons, so called hidden photons, have recently attracted some attention because they are a common feature of physics beyond the Standard Model like string theory and SUSY and additionally are phenomenologically of great interest regarding recent astrophysical observations. The hidden photon is already constrained by various laboratory experiments and presently searched for in running as well as upcoming experiments. We summarize the current status of limits on hidden photons from past electron beam dump experiments including two new limits from such experiments at KEK and Orsay that have so far not been considered. All our limits take into account the experimental acceptances obtained from Monte Carlo simulations.

  9. Global dumping ground: The international traffic in hazardous waste

    International Nuclear Information System (INIS)

    Moyers, B.

    1993-01-01

    This book is based on the PBS's television documentary. It vividly describes the forces that encourage the USA and other industrialized nations to condone the disposal of industrial and domestic hazardous wastes in other countries. Often conducted illegally, this disposal affects the unsuspecting people of less developed nations, many of whom have less stringent environmental laws and regulations. The book also portrays the ill effects of this dumping on the health and environment and convey and important messages: something must be done to get the public involved in repairing a serious global problem and even small measures, illustrated in the book, are a good start. However, the book fails to confront the question of how the public wants the government to be involved

  10. Wheel slip dump valve for railway braking system

    Science.gov (United States)

    Zhang, Xuan; Zhang, LiHao; Li, QingXuan; Shi, YanTao

    2017-09-01

    As we all know, pneumatic braking system plays an important role in the safety of the whole vehicle. In the anti slip braking system, the pressure of braking cylinder can be adjusted by the quick power response of wheel slip dump valve, so that the lock situation won’t occur during vehicle service. During the braking of railway vehicles, the braking force provided by braking disc reduces vehicle’s speed. But the locking slip will happen due to the oversize of braking force or the reduction of sticking coefficient between wheel and rail. It will cause not only the decline of braking performance but also the increase of braking distance. In the meanwhile, it will scratch the wheel and influence the stable running of vehicles. Now, the speed of passenger vehicle has been increased. In order to shorten the braking distance as far as possible, sticking stickiness must be fully applied. So the occurrence probability of wheel slip is increased.

  11. Design and development of multi-megawatt beam dumps

    International Nuclear Information System (INIS)

    Haughian, J.M.; Cooper, W.S.; Paterson, J.A.

    1976-11-01

    The next generation of U.S. fusion experiments which includes TFTR, MFTF, and Doublet III, will utilize neutral-beam injection for plasma heating. TFTR, for example, desires 20 MW of 120-keV deuterium atoms in pulses of 0.5-sec duration. In order to meet these requirements, a 15-A, 120-keV, 0.5-sec pulse per minute module is presently under test at the neutral-beam test facility at the Lawrence Berkeley Laboratory. A 65-A, 120-keV, 0.5-sec module is under construction and is scheduled for assembly in April of this year. Some of the features of a calorimeter/beam dump that is presently being used in the testing and evaluation of these neutral beam sources are discussed

  12. New limits on hidden photons from past electron beam dumps

    Energy Technology Data Exchange (ETDEWEB)

    Andreas, Sarah; Niebuhr, Carsten; Ringwald, Andreas

    2012-09-15

    Hidden sectors with light extra U(1) gauge bosons, so called hidden photons, have recently attracted some attention because they are a common feature of physics beyond the Standard Model like string theory and SUSY and additionally are phenomenologically of great interest regarding recent astrophysical observations. The hidden photon is already constrained by various laboratory experiments and presently searched for in running as well as upcoming experiments. We summarize the current status of limits on hidden photons from past electron beam dump experiments including two new limits from such experiments at KEK and Orsay that have so far not been considered. All our limits take into account the experimental acceptances obtained from Monte Carlo simulations.

  13. A multidomain chebyshev pseudo-spectral method for fluid flow and heat transfer from square cylinders

    KAUST Repository

    Wang, Zhiheng

    2015-01-01

    A simple multidomain Chebyshev pseudo-spectral method is developed for two-dimensional fluid flow and heat transfer over square cylinders. The incompressible Navier-Stokes equations with primitive variables are discretized in several subdomains of the computational domain. The velocities and pressure are discretized with the same order of Chebyshev polynomials, i.e., the PN-PN method. The Projection method is applied in coupling the pressure with the velocity. The present method is first validated by benchmark problems of natural convection in a square cavity. Then the method based on multidomains is applied to simulate fluid flow and heat transfer from square cylinders. The numerical results agree well with the existing results. © Taylor & Francis Group, LLC.

  14. The theory of pseudo-rigid bodies

    CERN Document Server

    Cohen, Harley

    1988-01-01

    This monograph concerns the development, analysis, and application of the theory of pseudo-rigid bodies. It collects together our work on that subject over the last five years. While some results have appeared else­ where, much of the work is new. Our objective in writing this mono­ graph has been to present a new theory of the deformation of bodies, one that has not only a firm theoretical basis, but also the simplicity to serve as an effective tool in practical problems. Consequently, the main body of the treatise is a multifaceted development of the theory, from foundations to explicit solutions to linearizations to methods of approximation. The fact that this variety of aspects, each examined in considerable detail, can be collected together in a single, unified treat­ ment gives this theory an elegance that we feel sets it apart from many others. While our goal has always been to give a complete treatment of the theory as it now stands, the work here is not meant to be definitive. Theories are not ent...

  15. Experimental pseudo-symmetric trap EPSILON

    International Nuclear Information System (INIS)

    Skovoroda, A.A.; Arsenin, V.V.; Dlougach, E.D.; Kulygin, V.M.; Kuyanov, A.Yu.; Timofeev, A.V.; Zhil'tsov, V.A.; Zvonkov, A.V.

    2001-01-01

    Within the framework of the conceptual project 'Adaptive Plasma EXperiment' a trap with the closed magnetic field lines 'Experimental Pseudo-Symmetric trap' is examined. The project APEX is directed at the theoretical and experimental development of physical foundations for stationary thermonuclear reactor on the basis of an alternative magnetic trap with tokamak-level confinement of high β plasma. The fundamental principle of magnetic field pseudosymmetry that should be satisfied for plasma to have tokamak-like confinement is discussed. The calculated in paraxial approximation examples of pseudosymmetric curvilinear elements with poloidal direction of B isolines are adduced. The EPSILON trap consisting of two straight axisymmetric mirrors linked by two curvilinear pseudosymmetric elements is considered. The plasma currents are short-circuited within the curvilinear element what increases the equilibrium β. The untraditional scheme of MHD stabilization of a trap with the closed field lines by the use of divertor inserted into axisymmetric mirror is analyzed. The experimental installation EPSILON-OME that is under construction for experimental check of divertor stabilization is discussed. The possibility of ECR plasma production in EPSILON-OME under conditions of high density and small magnetic field is examined. (author)

  16. Dissociative identity disorder and pseudo-hysteria.

    Science.gov (United States)

    Foote, B

    1999-01-01

    The diagnostic validity of dissociative identity disorder (DID) continues to inspire controversy, with some commentators claiming that DID is a modern variant of "hysteria"; that is, attention-seeking behavior. The author asserts that DID is indeed a valid psychiatric disorder, and believes that this skeptical reaction can largely be attributed to a specific set of transference/countertransference interactions that these patients tend to inspire. The paper delineates several clinical features of DID that can easily be mistaken for hysterical phenomena, and attempts to find the roots of this confusion in the DID patients' experience of interpersonal powerlessness, which leads them to present their symptoms in an unconvincing, "hysterical" manner. Confusion between the vertical split seen in the dissociative disorders and the horizontal split characteristic of the classic hysterical personality is discussed, as is the powerful effect of observer bias in creating hysterical-appearing phenomena. The term "pseudo-hysteria" is used to denote a situation in which a genuine psychiatric disorder, DID, is perceived as an hysterical production.

  17. An assessment of the radiological impact of sea-dumping at the North East Atlantic dump site

    International Nuclear Information System (INIS)

    Delow, C.E.; Mobbs, S.F.; Hill, M.D.

    1985-04-01

    This report describes the models and methodology developed for the assessment of the radiological impact of disposal of low and intermediate level waste on the seabed. The development of the waste package model and the combined model of radionuclide dispersion and interactions with sediments in the world's ocean is outlined. This integrated set of models was used for the radiological assessment of sea dumping at the North-East Atlantic site, which formed part of the recent NEA review of the continued suitability of this site. The predicted radiation doses to man are presented, together with the results of the analysis of the sensitivity of the annual individual doses to critical groups to variations in model parameters. (author)

  18. ISR RF cavities

    CERN Multimedia

    1983-01-01

    In each ISR ring the radiofrequency cavities were installed in one 9 m long straight section. The RF system of the ISR had the main purpose to stack buckets of particles (most of the time protons)coming from the CPS and also to accelerate the stacked beam. The installed RF power per ring was 18 kW giving a peak accelerating voltage of 20 kV. The system had a very fine regulation feature allowing to lower the voltage down to 75 V in a smooth and well controlled fashion.

  19. Formation of Mesoherpetobionts Communities on a Reclamated Coal Open Pit Dump

    Science.gov (United States)

    Luzyanin, Sergey; Eremeeva, Natalya

    2017-11-01

    The structure of the mesoherpetobionts arthropod communities of the reclamated dump of the Krasnobrodsky coal pit (Kemerovo region, Russia) has been studied. It was established that the pioneer grouping of mesoherpetobionts arthropod represented by classes of Chilopoda, Arachnida and Insecta-Ectognatha has been formed on the dump for two years after the soil deposition. From the Arachnida, the species of the order Aranei are the most active in the stocking of the dumps. From the class Chilopoda, the species of Lithobiomorpha appear the first on the dump. Insects from the following three orders, Heteroptera, Hymenoptera and especially Coleoptera take the main part in the expansion of dumps and the formation of primary communities. Among the Coleoptera, the beetles of the family of Carabidae (44 species, dynamic density 22.9 specimens/10 trapped per day) dominate. From them, small or medium-sized species are mainly involved in stocking the dumps. There are significant differences in the complexes of ground dump carabid beetles in comparison with the control group, differing in species composition of dominant species, species richness and species diversity parameters

  20. Northwest Russia and the Dumping of Radioactive Waste: The London Convention Implemented

    Energy Technology Data Exchange (ETDEWEB)

    Stokke, Olav Schram

    1997-12-31

    The `Polar Oceans and the Law of the Sea Project`, POLOS, is a three-year international research project in international law and international relations. This report is one of the publications under POLOS. The subject is the Soviet dumping of radioactive waste in the Barents and Kara Seas. The most intensely radioactive waste is a number of submarine reactors still containing high-level spent fuel. Some of this dumping violated Soviet commitments to the 1972 London Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter, and this is the starting point of the report. The discussion focuses on how international regimes may affect the domestic implementation in member states, that is, how international agreements can be converted into behavioural adaptation on the part of target groups. Soviet and later Russian management of nuclear waste in the north has been significantly influenced by regulations and programmes generated under international dumping instruments. These international programmes have been supported by the active participation of the Navy itself in the belief that they would lead to transfer of technology and financial resources to Russia from the West. Inspection of military nuclear waste management is largely left to the Northern Fleet. As for monitoring, measurements were for a long time not taken near the dumping sites. As for regulations, the Northern Fleet continued dumping long into the 1990s without permission. Regarding compliance stimulation, foreign support has helped the Northern Fleet avoid dumping. 113 refs.

  1. Monitoring of Thermal and Gas Activities in Mining Dump Hedvika, Czech Republic

    Science.gov (United States)

    Surovka, D.; Pertile, E.; Dombek, V.; Vastyl, M.; Leher, V.

    2017-10-01

    The negative consequences of mining of the black coal is occurrence of extractive waste storage locations - mining dumps. The mining activities carried out within the area of Ostrava are responsible for at least six mine dumps of loose materials arising as wastes from mining of mineral resources, many of which show presence of thermal processes. The thermal activity in dumps is responsible for many hazardous substances that pollute the environment and harm human health in the surroundings. This paper deals with the results of the first phase of project CZ.11.4.120/0.0/0.0/15_006/0000074 TERDUMP, on exploration of thermally active mining dumps are published in the article. As a first studied thermally active dump was a Hedvika dump. To localize of hot spots with hot gas emission was used a thermovision scanning by drone. The place with high temperature (49.8 °C) identified natural gas emission through natural cracks. Analysing the occurring pollutants in Hedvika Dump using the GC-MS or HPLC, respectively and the inert gases (CO2, CO and SO2) were determined by ion chromatography. The pollutants were determined in five sampling points during two measurements executed from July to August 2017.

  2. Flora and vegetation on dumps of uranium mining in the southern part of the former GDR

    Directory of Open Access Journals (Sweden)

    Hartmut Sänger

    2014-01-01

    Full Text Available From 1946 to 1990 an intensive uranium mining had been carried out with underground mining and also with opencast mining by the Wismut enterprise in the southern part of the former GDR. The mining activity lead also in the surroundings of Ronneburg to a permanent growth of devastated areas, among others in the form of dumps and tailings. These areas form by reason of mining-specific contaminations, extrem biotops which demand high claims on the pioneer organisms during the phase of natural first settlement. From 1990 to 1992 vegetation mappings were carried out on 15 dumps of the Thuringia mining area according to Braun-Blanquet (1964. The utilization of the computer programm Flora _D (Frank and Klotz 1990 enabled the ecological characterisation of the dumps. On the 15 investigated dumps found were 498 higher plants, belonging to 65 families. One hundred species are species with a high dominance. The number of species per dump fluctuates between 1 I and 282. Pioneer plants occur on the berms mostly in the second year after stoppage of the dumping, on the slopes after five to ten years. After nearly ten years the first step of settlement seems to be finished. Among the mechanisms of spreading dominate wind- and burdock spread. According to the form of life forms the dump species are predominantly hemicryptophytes, further therophytes, geophytes and phanerophytes.

  3. Design and construction of a resistive energy dump device for bipolar superconducting magnet systems

    Energy Technology Data Exchange (ETDEWEB)

    Mohan, M. J.

    1977-05-01

    When superconducting magnets quench, the resistance of the conductor material rises rapidly to its normal value. This increase in resistance can result in catastrophic heating in the magnet unless stored field energy is quickly removed from the system. Phase inversion is the normal mode of energy removal. SCR's in the power supply are phased back, the output of the supply is inverted, and magnetic field energy is directed back into the utility grid. Under certain conditions, however, the power supply may fail to invert properly, and an alternate energy removal scheme must protect the superconducting magnet system. Composed of an isolation switch, a semiconductor switching module, and a dump resistor, the resistive dump device provides a viable protection scheme. Operationally, several conditions are capable of activating the isolation switch and triggering the bipolar SCR switching module. Manual dump commands, for instance, permit the operator to dump field energy in the event of observed abnormalities. A special voltage tap quench detector senses the aforementioned abnormal power supply output inversion and also fires the dump circuit. Regardless of the nature of the trigger input, however, activation of the energy dump device diverts coil current through the dump resistor. I/sup 2/R losses over time then safely dissipate stored magnetic field energy.

  4. D0 Superconducting Solenoid Quench Data and Slow Dump Data Acquisition

    International Nuclear Information System (INIS)

    Markley, D.

    1998-01-01

    This Dzero Engineering note describes the method for which the 2 Tesla Superconducting Solenoid Fast Dump and Slow Dump data are accumulated, tracked and stored. The 2 Tesla Solenoid has eleven data points that need to be tracked and then stored when a fast dump or a slow dump occur. The TI555(Texas Instruments) PLC(Programmable Logic Controller) which controls the DC power circuit that powers the Solenoid, also has access to all the voltage taps and other equipment in the circuit. The TI555 constantly logs these eleven points in a rotating memory buffer. When either a fast dump(dump switch opens) or a slow dump (power supply turns off) occurs, the TI555 organizes the respective data and will down load the data to a file on DO-CCRS2. This data in this file is moved over ethernet and is stored in a CSV (comma separated format) file which can easily be examined by Microsoft Excel or any other spreadsheet. The 2 Tesla solenoid control system also locks in first fault information. The TI555 decodes the first fault and passes it along to the program collecting the data and storing it on DO-CCRS2. This first fault information is then part of the file.

  5. Aspects Regarding the Installation of Some Invasive Weeds Species on Old Fly Ash Dumps

    Directory of Open Access Journals (Sweden)

    Anca Pricop

    2010-10-01

    Full Text Available Most Romanian power plants were built in a period when environmental impact of their operation was undervalued, and constraints related to environmental protection were relatively few. Location of power plants and fly ash dumps was chosen most often by arbitrary criteria, and never after the impact that it may have on the environment. Building fly ash dumps have an effect of destruction of soils not only on the surface equivalent to those of dumps but also of the contiguous lands. Old fly ash dumps are a major risk because of the dispersion of pollutants in water and soil by percolation and soil leaching, and because of the unwanted invasion of weeds that are adaptable to arid conditions of the dumps and then invade surrounding areas jeopardizing the surrounding crops. In attempting to install vegetation an old fly ash dumps, the area were invaded by two species of weeds that quickly overgrown the experimental parcel and the surroundings. The present study followed the invasion degree of fly ash dumps with weeds and aspects regarding their development and breeding in the new formed ecosystem.

  6. Feasibility of In-Situ Aeration of Old Dumping Ground for Land Reclamation

    Directory of Open Access Journals (Sweden)

    Huan-Huan Tong

    2013-12-01

    Full Text Available Dumping grounds are characterized by the absence of engineering controls such as base liners and cover layer. Consequently, these dumping grounds present risks for surrounding resources such as soil, groundwater and air. The concern for groundwater contamination by leachate from tropical dumping grounds is heightened due to the greater amounts of rainfall and subsequent infiltration and percolation through the waste mass. The emergent demand for old dumping grounds reclamation drives the need to employ remediation technologies. Generally, in-situ aeration is a remediation method that promotes aerobic conditions in the later stage of dumping ground. It accelerates carbon transfer, reduces remaining organic load, and generally shortens the post closure period. However, high rainfall in tropical areas straitens this technique. For example, pollutants could be easily flushed out and more energy should be required to overcome hydrostatic pressure. Although heavy rainfall could supply sufficient water to the substrate and accelerate degradation of organic matter, it may inhibit aerobic activities due to limited air transfer. The waste characterization from Lorong Halus Dumping Ground (closed dumping ground in Singapore showed that the waste materials were stabilized after 22 years closure. According to the Waste Acceptance Criteria set by European Communities Council, the waste materials could be classified as inert wastes. One interesting finding was that leachate layer detected was about of 5 - 8 meter depth, which entirely soaked the waste materials. Hence, the reclamation design and operation should be carefully adjusted according to these characters. Lorong Halus Dumping Ground case study can provide a guideline for other tropical closed landfills or dumping grounds.

  7. Oral cavity eumycetoma

    Directory of Open Access Journals (Sweden)

    Gisele Alborghetti Nai

    2011-06-01

    Full Text Available Mycetoma is a pathological process in which eumycotic (fungal or actinomycotic causative agents from exogenous source produce grains. It is a localized chronic and deforming infectious disease of subcutaneous tissue, skin and bones. We report the first case of eumycetoma of the oral cavity in world literature. CASE REPORT: A 43-year-old male patient, complaining of swelling and fistula in the hard palate. On examination, swelling of the anterior and middle hard palate, with fistula draining a dark liquid was observed. The panoramic radiograph showed extensive radiolucent area involving the region of teeth 21-26 and the computerized tomography showed communication with the nasal cavity, suggesting the diagnosis of periapical cyst. Surgery was performed to remove the lesion. Histopathological examination revealed purulent material with characteristic grain. Gram staining for bacteria was negative and Grocott-Gomori staining for the detection of fungi was positive, concluding the diagnosis of eumycetoma. The patient was treated with ketoconazole for nine months, and was considered cured at the end of treatment. CONCLUSION: Histopathological examination, using histochemical staining, and direct microscopic grains examination can provide the distinction between eumycetoma and actinomycetoma accurately.

  8. Establishment of a multilateral consultation and surveillance mechanism for sea dumping of radioactive waste

    International Nuclear Information System (INIS)

    Strohl, Pierre.

    1977-01-01

    International regulations on dumping of radioactive waste which until only recently were limited to general principles, have developed significantly during the past years, while radioactive waste sea, dumping operations were being undertaken during the same period under the sponsorship of the OECD Nuclear Energy Agency. The latter, in implementation of the London Convention and the IAEA Recommendations, has established a mechanism whose purpose is to place under international control radioactive waste sea dumping operations to ensure that all necessary steps are taken to avoid marine pollution. This paper analyses the technical and legal aspects of the mechanism. (NEA) [fr

  9. The waste bin: nuclear waste dumping and storage in the Pacific

    International Nuclear Information System (INIS)

    Branch, J.B.

    1984-01-01

    Relatively small amounts of nuclear waste have been stored on Pacific islands and dumped into the Pacific Ocean since 1945. Governments of Pacific countries possessing nuclear power plants are presently seeking permanent waste storage and disposal solutions at Pacific sites including subseabed emplacement of high-level nuclear wastes and ocean dumping of low-level wastes. This article examines these plans and the response of Pacific islanders in their development of policies and international strategies to ban the proposed dumping on a regional basis. Island governments are preparing for a Regional Convention during which a treaty concerned with radioactive waste storage and disposal will be signed. (Author)

  10. Analysis of Geodynamical Conditions of Region of Burning Coal Dumps Location

    Science.gov (United States)

    Batugin, Andrian; Musina, Valeria; Golovko, Irina

    2017-12-01

    Spontaneous combustion of coal dumps and their impact on the environment of mining regions remain important environmental problem, in spite of the measures that are being taken. The paper presents the hypothesis, which states that the location of coal dumps at the boundaries of geodynamically active crust blocks promotes the appearance of conditions for their combustion. At present geodynamically active crust faults that affect the operating conditions of engineering facilities are observed not only in the areas of tectonic activity, but also on platforms. According to the concept of geodynamical zoning, geodynamically dangerous zones for engineering structures can be not only large, well-developed crust faults, but also just formed fractures that appear as boundaries of geodynamically impacting and hierarchically ordered crust blocks. The purpose of the study is to estimate the linkage of burning dumps to boundaries of geodynamically active crust blocks (geodynamically dangerous zones) for subsequent development of recommendations for reducing environmental hazard. The analysis of 27 coal dumps location was made for one of the Eastern Donbass regions (Russia). Nine of sixteen burning dumps are located in geodynamically dangerous zones, which, taking into account relatively small area occupied by all geodynamically dangerous zones, results that there is a concentration (pcs/km2) of burning dumps, which is 14 times higher than the baseline value. While the probability of accidental obtaining of such a result is extremely low, this can be considered as the evidence of the linkage of burning dumps to geodynamically dangerous zones. Taking into account the stressed state of the rock massif in this region, all geodynamically dangerous zones can be divided into compression and tension zones. The statistic is limited, but nevertheless in tension zones the concentration of burning dumps is 2 times higher than in compression zones. Available results of thermal monitoring of

  11. Ultrashort-pulse-train pump and dump excitation of a diatomic molecule

    Science.gov (United States)

    de Araujo, Luís E. E.

    2010-09-01

    An excitation scheme is proposed for transferring population between ground-vibrational levels of a molecule. The transfer is accomplished by pumping and dumping population with a pair of coherent ultrashort-pulse trains via a stationary state. By mismatching the teeth of the frequency combs associated with the pulse trains to the vibrational levels, high selectivity in the excitation, along with high transfer efficiency, is predicted. The pump-dump scheme does not suffer from spontaneous emission losses, it is insensitive to the pump-dump-train delay, and it requires only basic pulse shaping.

  12. Price strategy in the EU: Suggestions to Chinese exporters in the light of anti-dumping

    DEFF Research Database (Denmark)

    Nielsen, Jørgen Ulff-Møller

    2002-01-01

    This paper investigates the EU anti-dumping policy towards Chinese companies. It is based on the EU anti-dumping cases since 1990. Based on this analysis, the paper presents practical advice to Chinese or foreign managers in companies in China with export to the EU. Firstly, the CELEX database may...... give some important information on how to formulate a price policy for exports to the EU in order to avoid anti-dumping measures. Secondly, the owner structure of the company is important, if market economy status with its lower duties, is wanted. Wholly owned foreign companies or joint ventures...

  13. Assessment of the Influence of Dredge Spoil Dumping on the Seafloor Geological Integrity

    Directory of Open Access Journals (Sweden)

    Joonas J. Virtasalo

    2018-04-01

    Full Text Available The European Marine Strategy Framework Directive requires the development of suitable indicators for regular reporting on the environmental state and achievement of a good environmental status of EU's marine waters by 2020. The development of indicators for determining seafloor integrity and its possible disturbance by human activities have so far largely ignored the geological properties of seafloor. This paper presents a study of Vuosaari and Uusikaupunki-D offshore dumping sites in Finland, the northern Baltic Sea. Full coverage multibeam bathymetry and relative backscatter data, and a number of sediment cores were collected over the sites. The areas covered by dumped dredge spoil stand out in the multibeam images because of their irregular surface and elevated backscatter. The short gravity cores were studied for lithology, and in 1-cm slices for 137Cs activity, organic content, and grain size distribution. The dumped material is represented in the cores by the gravelly mud lithofacies with massive texture and angular coarse particles. The dumped material is coarser, less sorted and has higher kurtosis compared to natural sediment due to the admixing of blasted rock during the dredging activities, and limited sorting during fall through the water column upon dumping. Dispersed dredge spoil, which was suspended in the water column during the dumping activities or reworked from the dumped material mounds and redistributed along the seafloor soon thereafter, was deposited over a wide area as a thin layer that is not necessarily readily identifiable by visual inspection in the cores. Cesium activity helped distinguish the dumped material from the 137Cs-enriched natural sediments deposited after the 1986 Chernobyl disaster. Considering that the dumped material at many of the coring sites in the Vuosaari dumping area is covered by natural sediment, it probably is largely stable. In contrast, dumped material at the shallower Uusikaupunki-D site has

  14. Slope Stability Analysis of Waste Dump in Sandstone Open Pit Osielec

    Science.gov (United States)

    Adamczyk, Justyna; Cała, Marek; Flisiak, Jerzy; Kolano, Malwina; Kowalski, Michał

    2013-03-01

    This paper presents the slope stability analysis for the current as well as projected (final) geometry of waste dump Sandstone Open Pit "Osielec". For the stability analysis six sections were selected. Then, the final geometry of the waste dump was designed and the stability analysis was conducted. On the basis of the analysis results the opportunities to improve the stability of the object were identified. The next issue addressed in the paper was to determine the proportion of the mixture containing mining and processing wastes, for which the waste dump remains stable. Stability calculations were carried out using Janbu method, which belongs to the limit equilibrium methods.

  15. Pseudo-random bit generator based on lag time series

    Science.gov (United States)

    García-Martínez, M.; Campos-Cantón, E.

    2014-12-01

    In this paper, we present a pseudo-random bit generator (PRBG) based on two lag time series of the logistic map using positive and negative values in the bifurcation parameter. In order to hidden the map used to build the pseudo-random series we have used a delay in the generation of time series. These new series when they are mapped xn against xn+1 present a cloud of points unrelated to the logistic map. Finally, the pseudo-random sequences have been tested with the suite of NIST giving satisfactory results for use in stream ciphers.

  16. Pseudo-supersymmetry and the domain-wall/cosmology correspondence

    International Nuclear Information System (INIS)

    Skenderis, Kostas; Townsend, Paul K

    2007-01-01

    The correspondence between domain-wall and cosmological solutions of gravity coupled to scalar fields is explained. Any domain-wall solutions that admit a Killing spinor are shown to correspond to a cosmology that admits a pseudo-Killing spinor; whereas the Killing spinor obeys a Dirac-type equation with Hermitian 'mass'-matrix, the corresponding pseudo-Killing spinor obeys a Dirac-type equation with a anti-Hermitian 'mass'-matrix. We comment on some implications of (pseudo)supersymmetry

  17. The Fermi pseudo-potential in one dimension

    International Nuclear Information System (INIS)

    Coutinho, F A B; Nogami, Y; Tomio, Lauro; Toyama, F M

    2004-01-01

    Wu and Yu recently examined point interactions in one dimension in the form of the Fermi pseudo-potential. On the other hand there are point interactions in the form of self-adjoint extensions (SAEs) of the kinetic energy operator. We examine the relationship between the point interactions in these two forms in the one-channel and two-channel cases. In the one-channel case the pseudo-potential leads to the standard three-parameter family of SAEs. In the two-channel case the pseudo-potential furnishes a ten-parameter family of SAEs

  18. Open dumping of municipal solid waste and its hazardous impacts on soil and vegetation diversity at waste dumping sites of Islamabad city

    Directory of Open Access Journals (Sweden)

    Syeda Maria Ali

    2014-01-01

    Full Text Available Deteriorating soil quality and decrease in vegetation abundance are grave consequences of open waste dumping which have resulted in growing public concern. The focus of this study is to assess the contribution of open waste dumping in soil contamination and its effect on plant diversity in one of the renowned green cities of Pakistan. Surface soil samples (n = 12 + 12 were collected from both the open waste dumping areas allocated by Capital Development Authority (CDA and sub- sectors of H-belt of Islamabad city (representative of control site. The diversity of vegetation was studied at both sampling sites. Significant modifications were observed in the soil properties of the dumping sites. Soils at the disposal sites showed high pH, TDS and EC regime in comparison to control sites. Various heavy metal concentrations i.e., Lead (Pb, Copper (Cu, Nickel (Ni, Chromium (Cr and Zinc (Zn were also found to be higher at the dumping sites except for Cadmium (Cd which had a higher value in control site. A similar trend was observed in plant diversity. Control sites showed diversified variety of plants i.e., 44 plant species while this number reduced to only 32 plant species at the disposal sites. This is attributed to changes in soil characteristics at disposal sites and in its vicinity areas.

  19. Energy dump of the ATLAS superconducting system simulations of electrical and thermal behaviour of magnet system at slow- and fast dump

    CERN Document Server

    van Beek, Martijn; Dudarev, A

    During the slow dump (discharge) of the Barrel Toroidal (superconducting) magnet of the ATLAS detector, the control system gave an alarm that the differences between the voltages over the conductors were too high. The alarm was not due to any danger, because of some sort of phenomenon observed in the first few seconds after start of the discharge. A possible explanation of the differences of the coil voltages is that the changing current through the conductors may cause induced currents in the coil casing around. The goal was to make a simulation of the electrical behaviour of the magnet system during a slow dump. In this way, an explanation can be found for the start phenomenon of the slow dump of the Barrel Toroid. Some extra analyses on the measurements were performed to describe the energy dissipation during a fast dump. This is done by calculating the resistance of the coils during the dump. With the maximum resistance, the maximum temperature can be estimated, which says something about the enthalpy of ...

  20. Cryostat for TRISTAN superconducting cavity

    International Nuclear Information System (INIS)

    Mitsunobu, S.; Furuya, T.; Hara, K.

    1990-01-01

    Superconducting cavities generate rather high heat load of hundreds watts in one cryostat and have high sensitivity for pressure. We adopted usual pool-boiling type cooling for its stable pressure operation. Two 5-cell Nb cavities were installed in one flange type cryostat. Tuning mechanics actuated by a pulse-motor and a Piezo-electric element are set at outside of vacuum end flange. The design and performance of the cryostat for TRISTAN superconducting cavities are described. (author)

  1. Superconducting Radio-Frequency Cavities

    Science.gov (United States)

    Padamsee, Hasan S.

    2014-10-01

    Superconducting cavities have been operating routinely in a variety of accelerators with a range of demanding applications. With the success of completed projects, niobium cavities have become an enabling technology, offering upgrade paths for existing facilities and pushing frontier accelerators for nuclear physics, high-energy physics, materials science, and the life sciences. With continued progress in basic understanding of radio-frequency superconductivity, the performance of cavities has steadily improved to approach theoretical capabilities.

  2. CEBAF: Accelerating cavities look good

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1990-09-15

    The first assembled pairs of superconducting accelerating cavities from German supplier Interatom for the Continuous Electron Beam Accelerator Facility, Newport News, Virginia, have exceeded performance specifications.

  3. CEBAF: Accelerating cavities look good

    International Nuclear Information System (INIS)

    Anon.

    1990-01-01

    The first assembled pairs of superconducting accelerating cavities from German supplier Interatom for the Continuous Electron Beam Accelerator Facility, Newport News, Virginia, have exceeded performance specifications

  4. Chemical composition of fragmental products fractions of rock dumps and tailing dump as basis for potential geoecological danger estimation in the areas of mining enterprises

    Directory of Open Access Journals (Sweden)

    Vdovina Ol’ga Konstantinovna

    Full Text Available Negative consequences of deposit development on the environment are well know. They manifest themselves most intensively in case of open-cut mining of ore minerals, which is related to the increase of rock dumps masses. The material of rock dumps and tailing dumps actively influence the state of the environment transforming the natural landscapes, first of all, as a reason of migration of waters changed as a result of their contact with mining waste. The authors give their estimation of the consequences of apatite-nephelinic ore crop in Khibini Ore District by the company “Apatit”, which includes the influence on the natural waters. The unique natural conditions of the area are the reason for high-level potential geoecological danger. The mobility of lots of toxic elements is raised because of ligand-ion OH in the waters of alkali rocks of Khibini soil.

  5. Pseudo-Kähler Quantization on Flag Manifolds

    Science.gov (United States)

    Karabegov, Alexander V.

    A unified approach to geometric, symbol and deformation quantizations on a generalized flag manifold endowed with an invariant pseudo-Kähler structure is proposed. In particular cases we arrive at Berezin's quantization via covariant and contravariant symbols.

  6. A pseudo-random number generator and its spectral test

    International Nuclear Information System (INIS)

    Wang Lai

    1998-01-01

    The author introduces a pseudo-random number generator and describes its algorithm and C language implementation. The performance of the generator is tested and compared with some well known LCG generators

  7. Pseudo-random bit generator based on Chebyshev map

    Science.gov (United States)

    Stoyanov, B. P.

    2013-10-01

    In this paper, we study a pseudo-random bit generator based on two Chebyshev polynomial maps. The novel derivative algorithm shows perfect statistical properties established by number of statistical tests.

  8. Hardware implementation of a GFSR pseudo-random number generator

    Science.gov (United States)

    Aiello, G. R.; Budinich, M.; Milotti, E.

    1989-12-01

    We describe the hardware implementation of a pseudo-random number generator of the "Generalized Feedback Shift Register" (GFSR) type. After brief theoretical considerations we describe two versions of the hardware, the tests done and the performances achieved.

  9. A divergence theorem for pseudo-Finsler spaces

    OpenAIRE

    Minguzzi, E.

    2015-01-01

    We study the divergence theorem on pseudo-Finsler spaces and obtain a completely Finslerian version for spaces having a vanishing mean Cartan torsion. This result helps to clarify the problem of energy-momentum conservation in Finsler gravity theories.

  10. Pseudo-differential operators on manifolds with singularities

    CERN Document Server

    Schulze, B-W

    1991-01-01

    The analysis of differential equations in domains and on manifolds with singularities belongs to the main streams of recent developments in applied and pure mathematics. The applications and concrete models from engineering and physics are often classical but the modern structure calculus was only possible since the achievements of pseudo-differential operators. This led to deep connections with index theory, topology and mathematical physics. The present book is devoted to elliptic partial differential equations in the framework of pseudo-differential operators. The first chapter contains the Mellin pseudo-differential calculus on R+ and the functional analysis of weighted Sobolev spaces with discrete and continuous asymptotics. Chapter 2 is devoted to the analogous theory on manifolds with conical singularities, Chapter 3 to manifolds with edges. Employed are pseudo-differential operators along edges with cone-operator-valued symbols.

  11. Pseudo-differential operators groups, geometry and applications

    CERN Document Server

    Zhu, Hongmei

    2017-01-01

    This volume consists of papers inspired by the special session on pseudo-differential operators at the 10th ISAAC Congress held at the University of Macau, August 3-8, 2015 and the mini-symposium on pseudo-differential operators in industries and technologies at the 8th ICIAM held at the National Convention Center in Beijing, August 10-14, 2015. The twelve papers included present cutting-edge trends in pseudo-differential operators and applications from the perspectives of Lie groups (Chapters 1-2), geometry (Chapters 3-5) and applications (Chapters 6-12). Many contributions cover applications in probability, differential equations and time-frequency analysis. A focus on the synergies of pseudo-differential operators with applications, especially real-life applications, enhances understanding of the analysis and the usefulness of these operators.

  12. Pseudo-Goldstone modes in isospin-asymmetric nuclear matter

    International Nuclear Information System (INIS)

    Cohen, T.D.; Broniowski, W.

    1995-01-01

    The authors analyze the chiral limit in dense isospin-asymmetric nuclear matter. It is shown that the pseudo-Goldstone modes in this system are qualitatively different from the case of isospin-symmetric matter

  13. Hypokalaemia: Bartter's syndrome or pseudo-Bartter's syndrome?

    OpenAIRE

    Robb, J D; Delargy, M A; Nolan, M; Tomkin, G H

    1984-01-01

    The difficulties in the diagnosis of hypokalaemia are often considerable. This paper reports three patients who presented with hypokalaemia. Investigations are described which may help to distinguish Bartter's syndrome from pseudo-Bartter's syndrome.

  14. Graphical analysis of some pseudo-random number generators

    OpenAIRE

    Lewis, Peter A. W.

    1986-01-01

    There exist today many 'good' pseudo-random number generators; the problem is to retrieve them. This document discusses three commonly used pseudo- random number generators, the first being RANDU, a notoriously bad generator, but one which is still occasionally used. The next is the widely used prime modulus, multiplicative congruential generator used in LL-RANDOMII, the Naval Postgraduate School random number package, and the last is the random number generator provided for microcomputers wi...

  15. A Repetition Test for Pseudo-Random Number Generators

    OpenAIRE

    Gil, Manuel; Gonnet, Gaston H.; Petersen, Wesley P.

    2017-01-01

    A new statistical test for uniform pseudo-random number generators (PRNGs) is presented. The idea is that a sequence of pseudo-random numbers should have numbers reappear with a certain probability. The expectation time that a repetition occurs provides the metric for the test. For linear congruential generators (LCGs) failure can be shown theoretically. Empirical test results for a number of commonly used PRNGs are reported, showing that some PRNGs considered to have good statistical propert...

  16. Discrete Weighted Pseudo-Almost Automorphy and Applications

    Directory of Open Access Journals (Sweden)

    Zhinan Xia

    2014-01-01

    Full Text Available We deal with discrete weighted pseudo almost automorphy which extends some classical concepts and systematically explore its properties in Banach space including a composition result. As an application, we establish some sufficient criteria for the existence and uniqueness of the discrete weighted pseudo almost automorphic solutions to the Volterra difference equations of convolution type and also to nonautonomous semilinear difference equations. Some examples are presented to illustrate the main findings.

  17. Discrete Weighted Pseudo Asymptotic Periodicity of Second Order Difference Equations

    Directory of Open Access Journals (Sweden)

    Zhinan Xia

    2014-01-01

    Full Text Available We define the concept of discrete weighted pseudo-S-asymptotically periodic function and prove some basic results including composition theorem. We investigate the existence, and uniqueness of discrete weighted pseudo-S-asymptotically periodic solution to nonautonomous semilinear difference equations. Furthermore, an application to scalar second order difference equations is given. The working tools are based on the exponential dichotomy theory and fixed point theorem.

  18. Design of CMOS CFOA Based on Pseudo Operational Transconductance Amplifier

    OpenAIRE

    Hassan Jassim Motlak

    2015-01-01

    A novel design technique employing CMOS Current Feedback Operational Amplifier (CFOA) is presented. The feature of consumption very low power in designing pseudo-OTA is used to decreasing the total power consumption of the proposed CFOA. This design approach applies pseudo-OTA as input stage cascaded with buffer stage. Moreover, the DC input offset voltage and harmonic distortion (HD) of the proposed CFOA are very low values compared with the conventional CMOS CFOA due to...

  19. Zero-Shot Learning by Generating Pseudo Feature Representations

    OpenAIRE

    Lu, Jiang; Li, Jin; Yan, Ziang; Zhang, Changshui

    2017-01-01

    Zero-shot learning (ZSL) is a challenging task aiming at recognizing novel classes without any training instances. In this paper we present a simple but high-performance ZSL approach by generating pseudo feature representations (GPFR). Given the dataset of seen classes and side information of unseen classes (e.g. attributes), we synthesize feature-level pseudo representations for novel concepts, which allows us access to the formulation of unseen class predictor. Firstly we design a Joint Att...

  20. Intestinal sclerosis with pseudo-obstruction in three dogs.

    Science.gov (United States)

    Moore, R; Carpenter, J

    1984-04-01

    Intestinal sclerosis causing chronic intestinal pseudo-obstruction was diagnosed in 3 dogs. The pseudo-obstruction was characterized by vomiting and weight loss of 2 weeks' to 3 months' duration. A patent intestinal lumen was determined by contrast radiography and verified at surgery. Intestinal biopsy revealed diffuse atrophy, fibrosis, and mononuclear cell infiltration of the tunica muscularis. Each dog was euthanatized because of a progressive, deteriorating clinical course.

  1. Pseudo-tumoral hepatic tuberculosis discovered after surgical resection

    Directory of Open Access Journals (Sweden)

    Miloudi Nizar

    2012-02-01

    Full Text Available Pseudo-tumoral hepatic tuberculosis is rare. It is characterized by non-specific symptoms and radiological polymorphism. Diagnosis is problematic. This article presents three cases, each clinically different from each other, that illustrate how difficult diagnosis can be. The definitive diagnosis of pseudo-tumoral hepatic tuberculosis was reached on the basis of histological examination of surgical samples. Treatment of the disease based on appropriate anti-tubercular therapy generally gives a positive outcome.

  2. The Applied Communication Game: A Comment on Muma's "Communication Game: Dump and Play"

    Science.gov (United States)

    Longhurst, Thomas M.; Reichle, Joe E.

    1975-01-01

    Provided are some illustrative clinical uses of J. Muma's "dump" and "play" communication model (EC 073301), said to be most applicable to the less handicapped child who has "trained language" but needs to be taught interpersonal communication skills. (LS)

  3. 30 CFR 57.9303 - Construction of ramps and dumping facilities.

    Science.gov (United States)

    2010-07-01

    ... METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Loading, Hauling, and Dumping Safety Devices, Provisions, and Procedures for Roadways, Railroads...

  4. Hydrological investigations on an overburden dump in the Borken brown coal district, North Hessen

    International Nuclear Information System (INIS)

    Wolff, P.; Latif, A.

    1992-01-01

    After a general hydrological investigation of the Dosenberg overburden dump in North Hessen, a climatic water balance is established for the main vegetation periods of the years 1989, 1990, and 1991. This is followed by a description of the investigations of water levels of the plateau pools and time curves of water levels of observation holes drilled into the dump plateau. In all, the findings suggest that in the period under investigation, which comprised three draught years in sequence, the dump was largely an independent hydrological system. In this period, no significant discharge of water from the 'Dosenberg ecosystem' into the surrounding area occurred, i.e. the overburden dumps had no effect on the surrounding cultivated land and bodies of water. This may be different in wet years. On the other hand, the prevailing climate conditions give cause to assume that no negative effects need be expected. The investigation will be continued. (orig.) [de

  5. 75 FR 81533 - Antidumping Proceedings: Calculation of the Weighted Average Dumping Margin and Assessment Rate...

    Science.gov (United States)

    2010-12-28

    ... non-dumped comparisons. Several World Trade Organization (``WTO'') dispute settlement reports have... methodologies have been challenged as being inconsistent with the World Trade Organization (``WTO'') General... DEPARTMENT OF COMMERCE International Trade Administration 19 CFR Part 351 [Docket No. 101130598...

  6. Estimation of spatial variability of lignite mine dumping ground soil properties using CPTu results

    Directory of Open Access Journals (Sweden)

    Bagińska Irena

    2016-03-01

    Full Text Available The paper deals with application of CPTu test results for the probabilistic modeling of dumping grounds. The statistical measures use results from 42 CPT test points located in the lignite mine dumping ground from the region of Central Europe. Both the tip resistance qc as well as local friction fs are tested. Based on the mean values and standard deviations of measured quantities the specific zones in the dumping site profile are distinguished. For three main zones standard deviations of linearly de-trended functions, distributions of normalized de-trended values for qc and fs are examined. Also the vertical scales of fluctuation for both measured quantities are estimated. The obtained result shows that lignite mine dumping site can be successfully described with the Random Field Theory. Additional use of fs values introduces supplementary statistical information.

  7. An Engineering Model for Prediction of Waste Incineration in a Dump Combustor

    National Research Council Canada - National Science Library

    Arunajatesan, S

    1997-01-01

    An engineering model that can be used to obtain predictions of axial distributions of temperature and species concentrations in complex flows has been formulated and applied to waste incineration in a dump combustor...

  8. Changes to the LHC Beam Dumping System for LHC Run 2

    CERN Document Server

    Uythoven, Jan; Borburgh, Jan; Carlier, Etienne; Gabourin, Stéphane; Goddard, Brennan; Magnin, Nicolas; Senaj, Viliam; Voumard, Nicolas; Weterings, Wim

    2014-01-01

    The LHC beam dumping system performed according to expectations during Run 1 of the LHC (2009 – 2013). A brief overview of the experience is given, including a summary of the observed performance by comparison to expectations. An important number of changes are applied to the beam dumping system during the present Long Shutdown in order to further improve its safety and performance. They include the addition of a direct link between the Beam Interlock System and the re-triggering system of the dump kickers, the modification of the uninterrupted electrical power distribution architecture, the upgrade of the HV generators, the consolidation of the trigger synchronisation system, the modifications to the triggering system of the power switches and the changes to the dump absorbers TCDQ.

  9. Extracellular space, blood volume, and the early dumping syndrome after total gastrectomy

    Energy Technology Data Exchange (ETDEWEB)

    Miholic, J.; Reilmann, L.; Meyer, H.J.; Koerber, H.K.; Kotzerke, J.; Hecker, H. (Medzinische Hochschule Hannover (Germany, F.R.))

    1990-10-01

    Extracellular space and blood volume were measured using 82Br dilution and 51Cr-tagged erythrocytes in 24 tumor-free patients after total gastrectomy. Eleven of the patients suffered from early dumping. Age, blood volume, and extracellular space were significantly smaller in dumpers (P less than 0.05). The dumping score could be predicted by a multiple regression model considering blood volume per lean body mass and extracellular space (r = 0.637; P = 0.0039). Rapid (t1/2 less than 360 seconds) emptying of the gastric substitute, assessed using a 99Tc-labeled solid test meal, was significantly associated with dumping in addition to extracellular space and blood volume (r = 0.876; P = 0.0018). Both rapid emptying and a narrow extracellular space seem to contribute to the early dumping syndrome.

  10. A hybrid of QFD and AHP-TOPSIS for Durg dumping waste projects

    Directory of Open Access Journals (Sweden)

    Rituraj Chandrakar

    2018-06-01

    Full Text Available Generation of solid waste is the integral consequence of civilization and its management is stand-ing as a big challenge in front of state government at present time. Municipal solid waste in Durg-Bhilai is littered with improper places due to lack of understanding about the scientific im-portance of garbage and its consequences. Our foremost concern is the selection of appropriate dumping area nearby Durg-Bhilai (C.G. and for the selection of appropriate dumping area, a multi criteria decision making technique is used. This paper attempts to evaluate 4 dumping areas based on 5 criteria. Analytical hierarchy process (AHP is used to determine the weighs for each criterion and quality function deployment (QFD is also implemented. The results indicate that Potiyakala was the best dumping site nearby Durg-Bhilai area.

  11. Design considerations for a steady state fusion reactor's thermal energy dump (TED) with emphasis on SAFFIRE

    International Nuclear Information System (INIS)

    Werley, K.A.

    1980-01-01

    This work examines the use of a thermal dump to handle the severe particle and energy handling requirements of a diverted plasma. We outline a general approach for evaluating the design parameters and limitations of a thermal dump, considering such things as thermomechanical and erosion effects, compatibility, availability, machinability, coolant recirculation, vacuum pumping, economics, lifetime, etc. To demonstrate how the performance requirements are reflected in design decisions, we apply a solid-walled dump to a small-sized field reversed mirror (FRM). We also examine a liquid-lithium droplet thermal dump and point out some distinct advantages of this new concept over the solid-wall design in reducing stress, erosion, and vacuum pumping problems. The chief disadvantages of this scheme include liquid-metal safe-handling problems, vapor pressure-temperature limitations, and the need for differential pumping if T/sub Li/ > 310 0 C is desired

  12. Fort George G. Meade Active Sanitary Landfill and Clean Fill Dump, Remedial Investigation Report

    National Research Council Canada - National Science Library

    1992-01-01

    ...) and a Site Inspection at the inactive Clean Fill Dump (CFD) sites. The objective of the ASL study involved obtaining additional data to evaluate the potential environmental impacts associated with the landfill operations...

  13. Forecast salt regime unwatered mine reclaimed dump in unstable conditions in Western Donbass

    Directory of Open Access Journals (Sweden)

    Yevhrashkina H.P.

    2016-02-01

    Full Text Available On the based theory of physical-chemical hydrodynamic of porous media was executed prognosis salt rate no suppying with water mine dumps of minimum sense transhiration in conditions no established rate.

  14. Development of the heat sink structure of a beam dump for the proton accelerator

    International Nuclear Information System (INIS)

    Maeng, W. Y.; Gil, C. S.; Kim, J. H.; Kim, D. H.

    2007-01-01

    The beam dump is the essential component for the good beam quality and the reliable performance of the proton accelerator. The beam dump for a 20 MeV and 20 mA proton accelerator was designed and manufactured in this study. The high heats deposited, and the large amount of radioactivity produced in beam dump should be reduced by the proper heat sink structure. The heat source by the proton beam of 20 MeV and 20 mA was calculated. The radioactivity assessments of the beam dump were carried out for the economic shielding design with safety. The radioactivity by the protons and secondary neutrons in designed beam dump were calculated in this sturdy. The effective engineering design for the beam dump cooling was performed, considering the mitigation methods of the deposited heats with small angle, the power densities with the stopping ranges in the materials and the heat distributions in the beam dump. The heat sink structure of the beam dump was designed to meet the accelerator characteristics by placing two plates of 30 cm by 60 cm at an angle of 12 degree. The highest temperatures of the graphite, copper, and copper faced by cooling water were designed to be 223 degree, 146 degree, and 85 degree, respectively when the velocity of cooling water was 3 m/s. The heat sink structure was manufactured by the brazing graphite tiles to a copper plate with the filler alloy of Ti-Cu-Ag. The brazing procedure was developed. The tensile stress of the graphite was less than 75% of a maximum tensile stress during the accelerator operation based on the analysis. The safety analyses for the commissioning of the accelerator operation were also performed. The specimens from the brazed parts of beam dump structure were made to identify manufacturing problems. The soundness of the heat sink structure of the beam dump was confirmed by the fatigue tests of the brazed specimens of the graphite-copper tile components with the repetitive heating and cooling. The heat sink structure developed

  15. A scramble for data on Arctic radioactive dumping

    International Nuclear Information System (INIS)

    Marshall, E.

    1992-01-01

    On 15 August, a Russian research vessel, the Viktor Buynitskiy, will leave the Norwegian port of Kirkenes packed with surveying equipment and scientists. Its mission will be to check out one of the more alarming environmental stories that have drifted out of the former Soviet Union since its collapse last fall: a claim that the Arctic is being polluted by tons of radioactive waste spilled or dumped by the Soviet military. Since May, US officials have been searching for information to confirm or disprove the reports about Russian radiation. The basic concern, is as follows: Arctic waters - and, potentially, fisheries near Norway and Alaska - are in danger of being contaminated by radioactive isotopes leaking from two major sources. One is the area around Novaya Zemlya, an archipelago where the Soviets conducted bomb tests, scuttled submarines, and disposed of waste canisters. The other is freshwater runoff into the Arctic Ocean - including the Ob and Yenisey Rivers - carrying isotopes from weapons plants, waste ponds, and accident sites in Siberia

  16. Reclamation of coal mine spoil dump through integrated biotechnological approach

    International Nuclear Information System (INIS)

    Juwarkar, A.S.; Thawale, P.R.; Mowade, S.; Shrivastava, S.; Deshbhratar, P.B.; Juwarkar, A.

    1994-01-01

    Laboratory and field studies were carried out to restore the fertility and productivity of coal mine spoil using primary clarifier sludge from paper mill effluent treatment plant and use of specialised culture of biofertilizers and mycorrhizal fungi. Plants namely Tectona grandis, Delbergia sissoo, Gmelina arporea, Emblica officinalis and Cassia seamea were grown. Sludge amendment enhanced the survival rate of plants to 80% compared to 20% in unamended spoil. Plants grown on unamended spoil showed stunted growth. Growth of plants increased by 188-484% when sludge was applied at the rate of 100 tonnes per hectare. At 100 tones per hectare sludge amendment, biofertilizer and mycorrhizae treatment there were 83.7 nodules in shishum as against only 4.6 nodules in case of spoil alone. Further root length was 276% and 281% more respectively in case of shishum and teak. Inoculation of plant saplings with respective biofertilizers and mycorrhizae further increased the plant growth by 144-198%. At Durgapur coal mine, 56,000 saplings of Tectona grandis, Gmelina arporea, Delbergia sissoo, Emblica officinalis, Azadirachta indica, Acacia ariculiformis, Prosopis etc were successfully planted on spoil dump using integrated biotechnological approach. 10 refs., 5 tabs

  17. Upgrade of the Super Proton Synchrotron Vertical Beam Dump System

    CERN Document Server

    Senaj, V; Vossenberg, E

    2010-01-01

    The vertical beam dump system of the CERN Super Proton Synchrotron (SPS) uses two matched magnets with an impedance of 2 W and a combined kick strength of 1.152 Tm at 60 kV supply voltage. For historical reasons the two magnets are powered from three 3 W pulse forming networks (PFN) through three thyratronignitron switches. Recently flashovers were observed at the entry of one of the magnets, which lead, because of the electrical coupling between the kickers, to a simultaneous breakdown of the pulse in both magnets. To improve the reliability an upgrade of the system was started. In a first step the radii of surfaces at the entry of the weak magnet were increased, and the PFN voltage was reduced by 4%; the kick strength could be preserved by reducing the magnet termination resistance by 10 %. The PFNs were protected against negative voltage reflections and their last cell was optimised. In a second step the two magnets will be electrically separated and powered individually by new 2 W PFNs with semiconductor ...

  18. Conceptual plan for 100-N Emergency Dump Basin (EDB) deactivation

    International Nuclear Information System (INIS)

    Davis, C.M.; Day, R.S.; Smith, D.L.

    1996-07-01

    This document provides the conceptual plan for the 100-N Emergency Dump Basin (EDB) located at the Hanford Site in Richland, Washington. The EDB is an outdoor concrete retention pond with a carbon-steel liner underlain with fiberglass. The EDB was originally designed as a quenching pool for reactor blowdown in event of a primary coolant leak. However, the EDB only received routine steam-generator blowdowns from 1963 to 1987. The steam-generator blowdown and leaking isolation valves allowed radioactively contaminated water (from primary and secondary reactor coolant leaks) to enter the EDB. Over the years, wind-blown sand and dust have settled in the EDB, resulting in the present layer of sediments. As of February 1996, the EDB contained an estimated 260,000 gal of water and approximately 2,300 ft3 of sediment. The average sediment thickness is estimated at 2.5 ft and is covered with approximately 12 ft to 14 ft of water. Vegetation (mostly reeds and cattails) grows in the basin corners where the sediment is exposed. To minimize animal and bird intrusion, a kneeling net has been installed over the EDB

  19. Disposal of sediments from the 1300-N Emergency Dump Basin

    International Nuclear Information System (INIS)

    Keen, R.; Duncan, G.M.

    1996-01-01

    This report describes the characterization of the 1300-N Emergency Dump Basin (EDB) sediments, summarizes the data obtained, the resultant waste categorization, and the preferred disposal method. The EDB is an outdoor, concrete storage pond with a 3/16-in. carbon steel liner. The basin (completed in 1963) originally served as a quenching pool for reactor blowdown in the event of a primary coolant leak. Later, the basin received blowdown from the N Reactor steam generators. The steam generator blowdowns and leading isolation valves allowed radioactively contaminated water (from primary and secondary reactor coolant leaks) to enter the basin. Windblown dust and sand have settled in the basin over the years (because of its outdoor location), causing the present layer of sediments. To minimize potential airborne contamination, the water level was kept constant by adding water. However, the addition of water was stopped to minimize the amount of contaminated water needing disposal. To ensure that the surfaces exposed as a result of evaporation pose no immediate airborne contaminant problem, the contamination levels are monitored by Radiation Control Technicians. As part of the deactivation of N Reactor facilities, the EDB will be stabilized for long-term surveillance and maintenance prior to final decontamination and demolition

  20. Pseudo-simple heteroclinic cycles in R4

    Science.gov (United States)

    Chossat, Pascal; Lohse, Alexander; Podvigina, Olga

    2018-06-01

    We study pseudo-simple heteroclinic cycles for a Γ-equivariant system in R4 with finite Γ ⊂ O(4) , and their nearby dynamics. In particular, in a first step towards a full classification - analogous to that which exists already for the class of simple cycles - we identify all finite subgroups of O(4) admitting pseudo-simple cycles. To this end we introduce a constructive method to build equivariant dynamical systems possessing a robust heteroclinic cycle. Extending a previous study we also investigate the existence of periodic orbits close to a pseudo-simple cycle, which depends on the symmetry groups of equilibria in the cycle. Moreover, we identify subgroups Γ ⊂ O(4) , Γ ⊄ SO(4) , admitting fragmentarily asymptotically stable pseudo-simple heteroclinic cycles. (It has been previously shown that for Γ ⊂ SO(4) pseudo-simple cycles generically are completely unstable.) Finally, we study a generalized heteroclinic cycle, which involves a pseudo-simple cycle as a subset.

  1. Geophysical exploration of historical mine dumps for the estimation of valuable residuals

    Science.gov (United States)

    Martin, Tina; Knieß, Rudolf; Noell, Ursula; Hupfer, Sarah; Kuhn, Kerstin; Günther, Thomas

    2015-04-01

    Within the project ROBEHA, funded by the German Federal Ministry of Education and Research (033R105) the economic potential of different abandoned dump sites for mine waste in the Harz Mountains was investigated. Two different mining dumps were geophysically and mineralogically analysed in order to characterize the mine dump structure and to estimate the volume of the potential recycling material. The geophysical methods comprised geoelectrics, radar, and spectral induced polarization (SIP). One about 100-year old mining dump containing residues from density separated Ag- and Sb-rich Pb (Zn)-gangue ores was investigated in detail. Like most small-scale mining waste disposal sites this investigated dump is very heterogeneously structured. Therefore, 27 geoelectrical profiles, more than 50 radar profiles, and several SIP profiles were measured and analysed. The results from the radar measurements, registered with the GSSI system and a shielded 200 MHz antenna, show the near surface boundary layer (down to 3-4 m beneath surface) of the waste residuals. These results can be used as pre-information for the inversion process of the geoelectrical data. The geoelectrical results reveal the mineral residues as layers with higher resistivities (> 300 Ohm*m) than the surrounding material. The SIP method found low phase signals (mine dump and other parameters we get a first estimate for the volume of the residues but the economical viability and the environmental impact of the reworking of the dump still needs to be evaluated in detail. The results of the second mine dump, an abandoned Cu and Zn-rich slag heap, show that the slag residues are characterized by higher resistivities and higher phases. A localization of the slag residues which are covered by organic material could be realized applying these geophysical methods.

  2. Mathematical model of vertical mass transport in the mine dumps Western Donbass

    Directory of Open Access Journals (Sweden)

    Yevhrashkina T.P.

    2012-09-01

    Full Text Available The multivariate mathematical models of the recultivated, recultivated and dumping with dry system, recultivated in systematically irrigation conditions and free of overgrowth by wild plants are proposed, designed and quantified. The theory of physico-chemical hydrodynamics of pore space using analytical and numerical methods for solving the equations of motion and mass conservation of matter all models are based on. The adequacy of built models and man-maid processes that proceed inside the mine dumps is proved.

  3. Making ultracold molecules in a two color pump-dump photoassociation scheme using chirped pulses

    OpenAIRE

    Koch, Christiane P.; Luc-Koenig, Eliane; Masnou-Seeuws, Françoise

    2005-01-01

    This theoretical paper investigates the formation of ground state molecules from ultracold cesium atoms in a two-color scheme. Following previous work on photoassociation with chirped picosecond pulses [Luc-Koenig et al., Phys. Rev. A {\\bf 70}, 033414 (2004)], we investigate stabilization by a second (dump) pulse. By appropriately choosing the dump pulse parameters and time delay with respect to the photoassociation pulse, we show that a large number of deeply bound molecules are created in t...

  4. Tracking of the nuclear wavepacket motion in cyanine photoisomerization by ultrafast pump-dump-probe spectroscopy.

    Science.gov (United States)

    Wei, Zhengrong; Nakamura, Takumi; Takeuchi, Satoshi; Tahara, Tahei

    2011-06-01

    Understanding ultrafast reactions, which proceed on a time scale of nuclear motions, requires a quantitative characterization of the structural dynamics. To track such structural changes with time, we studied a nuclear wavepacket motion in photoisomerization of a prototype cyanine dye, 1,1'-diethyl-4,4'-cyanine, by ultrafast pump-dump-probe measurements in solution. The temporal evolution of wavepacket motion was examined by monitoring the efficiency of stimulated emission dumping, which was obtained from the recovery of a ground-state bleaching signal. The dump efficiency versus pump-dump delay exhibited a finite rise time, and it became longer (97 fs → 330 fs → 390 fs) as the dump pulse was tuned to longer wavelengths (690 nm → 950 nm → 1200 nm). This result demonstrates a continuous migration of the leading edge of the wavepacket on the excited-state potential from the Franck-Condon region toward the potential minimum. A slowly decaying feature of the dump efficiency indicated a considerable broadening of the wavepacket over a wide range of the potential, which results in the spread of a population distribution on the flat S(1) potential energy surface. The rapid migration as well as broadening of the wavepacket manifests a continuous nature of the structural dynamics and provides an intuitive visualization of this ultrafast reaction. We also discussed experimental strategies to evaluate reliable dump efficiencies separately from other ultrafast processes and showed a high capability and possibility of the pump-dump-probe method for spectroscopic investigation of unexplored potential regions such as conical intersections. © 2011 American Chemical Society

  5. Ultrashort-pulse-train pump and dump excitation of a diatomic molecule

    OpenAIRE

    de Araujo, LEE

    2010-01-01

    An excitation scheme is proposed for transferring population between ground-vibrational levels of a molecule. The transfer is accomplished by pumping and dumping population with a pair of coherent ultrashort-pulse trains via a stationary state. By mismatching the teeth of the frequency combs associated with the pulse trains to the vibrational levels, high selectivity in the excitation, along with high transfer efficiency, is predicted. The pump-dump scheme does not suffer from spontaneous emi...

  6. BIO-PEDO-GEOGRAPHYCAL REGARDS ON GARBAGE DUMPS FROM TOMEŞTI - IAŞI

    Directory of Open Access Journals (Sweden)

    C. Secu

    2005-10-01

    Full Text Available The garbage dump from Tomeşti (Iaşi represents a water and soil pollution source, as well as a peril for the population’s health. The study has pursued the analysis of some indicators of water quality (which have evidenced exceeds of the currently admitted values, the identification of the plant species from the garbage dump perimeter (table 1 and the presentation of the general geographical landscape.

  7. Thermomagnetic Stability in Pseudo Single Domain Grains

    Science.gov (United States)

    Nagy, Lesleis; Williams, Wyn; Muxworthy, Adrian; Fabian, Karl; Conbhuí, Pádraig Ó.

    2016-04-01

    The reliability of paleomagnetic remanences are well understood for fine grains of magnetite that are single-domain (SD, uniformly magnetized). In particular Néel's theory [1] outlined the thermal energies required to block and unblock magnetic remanences. This lead to determination of thermal stability for magnetization in fine grains as outlined in Pullaiah et. al. [2] and a comprehensive understanding of SD paleomagnetic recordings. It has been known for some time that single domain magnetite is possible only in the grain size range 30 - 80nm, which may only account for a small fraction of the grain size distribution in any rock sample. Indeed rocks are often dominated by grains in the pseudo single domain (PSD) size range, at approximately 80 - 1000nm. Toward the top end of this range multi-domain features begin to dominate. In order to determine thermomagnetic stability in PSD grains we need to identify the energy barriers between all possible pairs of local energy minima (LEM) domain states as a function of both temperature and grain size. We have attempted to do this using the nudged elastic band (NEB) method [3] which searches for minimum energy paths between any given pair of LEM states. Using this technique we have determined, for the first time, complete thermomagnetic stability curves for PSD magnetite. The work presented is at a preliminary stage. However it can be shown that PSD grains of magnetite with simple geometries (e.g. cubes or cuboctahedra) have very few low energy transition paths and the stability is likely to be similar to that observed for SD grains (as expected form experimental observations). The results will provide a basis for a much more rigorous understanding of the fidelity of paleomagnetic signals in assemblages of PSD grains and their ability to retain ancient recordings of the geomagnetic field. References: [1] Néel, Louis. "Théorie du traînage magnétique des ferromagnétiques en grains fins avec applications aux terres

  8. Single and Coupled Nanobeam Cavities

    DEFF Research Database (Denmark)

    Ivinskaya, Aliaksandra; Lavrinenko, Andrei; Shyroki, Dzmitry M.

    2013-01-01

    for analysis and design of photonic crystal devices, such as 2D ring resonators for filters, single and coupled nanobeam cavities, birefringence in photonic crystal cavities, threshold analysis in photonic crystal lasers, gap solitons in photonic crystals, novel photonic atolls, dynamic characteristics...

  9. External post-operational checks for the LHC beam dumping system

    International Nuclear Information System (INIS)

    Magnin, N.; Baggiolini, V.; Carlier, E.; Goddard, B.; Gorbonosov, R.; Khasbulatov, D.; Uythoven, J.; Zerlauth, M.

    2012-01-01

    The LHC Beam Dumping System (LBDS) is a critical part of the LHC machine protection system. After every LHC beam dump action the various signals and transient data recordings of the beam dumping control systems and beam instrumentation measurements are automatically analysed by the external Post-Operational Checks (XPOC) system to verify the correct execution of the dump action and the integrity of the related equipment. This software system complements the LHC machine protection hardware, and has to ascertain that the beam dumping system is 'as good as new' before the start of the next operational cycle. This is the only way by which the stringent reliability requirements can be met. The XPOC system has been developed within the framework of the LHC 'Post-Mortem' system, allowing highly dependable data acquisition, data archiving, live analysis of acquired data and replay of previously recorded events. It is composed of various analysis modules, each one dedicated to the analysis of measurements coming from specific equipment. This paper describes the global architecture of the XPOC system and gives examples of the analyses performed by some of the most important analysis modules. It explains the integration of the XPOC into the LHC control infrastructure along with its integration into the decision chain to allow proceeding with beam operation. Finally, it discusses the operational experience with the XPOC system acquired during the first years of LHC operation, and illustrates examples of internal system faults or abnormal beam dump executions which it has detected. (authors)

  10. Simulation of the Beam Dump for a High Intensity Electron Gun

    CERN Document Server

    Doebert, S; Lefevre, T; Pepitone, K

    2014-01-01

    The CLIC Drive Beam is a high-intensity pulsed electron beam. A test facility for the Drive Beam electron gun will soon be commissioned at CERN. In this contribution we outline the design of a beam dump / Faraday cup capable of resisting the beam’s thermal load. The test facility will operate initially up to 140 keV. At such low energies, the electrons are absorbed very close to the surface of the dump, leading to a large energy deposition density in this thin layer. In order not to damage the dump, the beam must be spread over a large surface. For this reason, a small-angled cone has been chosen. Simulations using Geant4 have been performed to estimate the distribution of energy deposition in the dump. The heat transport both within the electron pulse and between pulses has been modelled using finite element methods to check the resistance of the dump at high repetition rates. In addition, the possibility of using a moveable dump to measure the beam profile and emittance is discussed.

  11. Technical tasks in superconducting cavities

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Kenji [High Energy Accelerator Research Organization, Tsukuba, Ibaraki (Japan)

    1997-11-01

    The feature of superconducting rf cavities is an extremely small surface resistance on the wall. It brings a large energy saving in the operation, even those are cooled with liquid helium. That also makes possible to operate themselves in a higher field gradient comparing to normal conducting cavities, and brings to make accelerators compact. These merits are very important for the future accelerator engineering which is planed at JAERI for the neutron material science and nuclear waste transmutation. This machine is a high intensity proton linac and uses sc cavities in the medium and high {beta} sections. In this paper, starting R and D of proton superconducting cavities, several important technical points which come from the small surface resistance of sc cavities, are present to succeed it and also differences between the medium and high - {beta} structures are discussed. (author)

  12. Pacer processing: cavity inventory relationships

    International Nuclear Information System (INIS)

    Dietz, R.J.; Gritzo, L.A.

    1975-09-01

    The pacer cavity and its associated primary power loop comprise a recirculating system in which materials are introduced by a series of thermonuclear explosions while debris is continuously removed by radioactive decay, sorption phenomena, and deliberate processing. Safe, reliable, and economical realization of the Pacer concept depends on the removal and control of both noxious and valuable by-products of the fusion reaction. Mathematical relationships are developed that describe the quantities of materials that are introduced into the Pacer cavity by a series of discrete events and are removed continuously by processing and decay. An iterative computer program based on these relationships is developed that allows both the total cavity inventory and the amounts of important individual species to be determined at any time during the lifetime of the cavity in order to establish the effects of the thermonuclear event, the cavity, the flow, and various processing parameters on Pacer design requirements

  13. Decompositions, partitions, and coverings with convex polygons and pseudo-triangles

    NARCIS (Netherlands)

    Aichholzer, O.; Huemer, C.; Kappes, S.; Speckmann, B.; Tóth, Cs.D.

    2007-01-01

    We propose a novel subdivision of the plane that consists of both convex polygons and pseudo-triangles. This pseudo-convex decomposition is significantly sparser than either convex decompositions or pseudo-triangulations for planar point sets and simple polygons. We also introduce pseudo-convex

  14. Feasibility of MR-only proton dose calculations for prostate cancer radiotherapy using a commercial pseudo-CT generation method

    Science.gov (United States)

    Maspero, Matteo; van den Berg, Cornelis A. T.; Landry, Guillaume; Belka, Claus; Parodi, Katia; Seevinck, Peter R.; Raaymakers, Bas W.; Kurz, Christopher

    2017-12-01

    A magnetic resonance (MR)-only radiotherapy workflow can reduce cost, radiation exposure and uncertainties introduced by CT-MRI registration. A crucial prerequisite is generating the so called pseudo-CT (pCT) images for accurate dose calculation and planning. Many pCT generation methods have been proposed in the scope of photon radiotherapy. This work aims at verifying for the first time whether a commercially available photon-oriented pCT generation method can be employed for accurate intensity-modulated proton therapy (IMPT) dose calculation. A retrospective study was conducted on ten prostate cancer patients. For pCT generation from MR images, a commercial solution for creating bulk-assigned pCTs, called MR for Attenuation Correction (MRCAT), was employed. The assigned pseudo-Hounsfield Unit (HU) values were adapted to yield an increased agreement to the reference CT in terms of proton range. Internal air cavities were copied from the CT to minimise inter-scan differences. CT- and MRCAT-based dose calculations for opposing beam IMPT plans were compared by gamma analysis and evaluation of clinically relevant target and organ at risk dose volume histogram (DVH) parameters. The proton range in beam’s eye view (BEV) was compared using single field uniform dose (SFUD) plans. On average, a (2%, 2 mm) gamma pass rate of 98.4% was obtained using a 10% dose threshold after adaptation of the pseudo-HU values. Mean differences between CT- and MRCAT-based dose in the DVH parameters were below 1 Gy (radiotherapy, is feasible following adaptation of the assigned pseudo-HU values.

  15. Restoration of fly ash dump through biological interventions.

    Science.gov (United States)

    Juwarkar, Asha A; Jambhulkar, Hemlata P

    2008-04-01

    Field experiment on 10 ha area of fly ash dump was conducted to restore and revegetate it using biological interventions, which involves use of organic amendment, selection of suitable plant species along with specialized nitrogen fixing strains of biofertilizer. The results of the study indicated that amendment with farm yard manure at 50 t/ha improved the physical properties of fly ash such as maximum water holding capacity from 40.0 to 62.42% while porosity improved from 56.78 to 58.45%. The nitrogen content was increased by 4.5 times due to addition of nitrogen fixing strains of Bradyrhizobium and Azotobacter species, while phosphate content was increased by 10.0 times due to addition of VAM, which helps in phosphate immobilization. Due to biofertilizer inoculation different microbial groups such as Rhizobium, Azotobacter and VAM spores, which were practically absent in fly ash improved to 7.1 x 10(7), 9.2 x 10(7) CFU/g and 35 VAM spores/10 g of fly ash, respectively. Inoculation of biofertilizer and application of FYM helped in reducing the toxicity of heavy metals such as cadmium, copper, nickel and lead which were reduced by 25, 46, 48 and 47%, respectively, due to the increased organic matter content in the fly ash which complexes the heavy metals thereby decreasing the toxicity of metals. Amendment of fly ash with FYM and biofertilizer helped in profuse root development showing 15 times higher growth in Dendrocalamus strictus plant as compared to the control. Thus amendment and biofertilizer application provided better supportive material for anchorage and growth of the plant.

  16. Ranking criteria for assessment of municipal solid waste dumping sites

    Directory of Open Access Journals (Sweden)

    Mahmood Khalid

    2017-03-01

    Full Text Available Priority wise channelization of resources is the key to successful environmental management, especially when funds are limited. The study in hand has successfully developed an algorithmic criterion to compare hazardous effects of Municipal Solid Waste (MSW dumping sites quantitatively. It is a Multi Criteria Analysis (MCA that has made use of the scaling function to normalize the data values, Analytical Hierarchy Process (AHP for assigning weights to input parameters showing their relevant importance, and Weighted Linear Combination (WLC for aggregating the normalized scores. Input parameters have been divided into three classes namely Resident’s Concerns, Groundwater Vulnerability and Surface Facilities. Remote Sensing data and GIS analysis were used to prepare most of the input data. To elaborate the idea, four dumpsites have been chosen as case study, namely Old-FSD, New-FSD, Saggian and Mahmood Booti. The comparison has been made first at class levels and then class scores have been aggregated into environmental normalized index for environmental impact ranking. The hierarchy of goodness found for the selected sites is New-FSD > Old-FSD > Mahmood Booti > Saggian with comparative scores of goodness to environment as 36.67, 28.43, 21.26 and 13.63 respectively. Flexibility of proposed model to adjust any number of classes and parameters in one class will be very helpful for developing world where availability of data is the biggest hurdle in research based environmental sustainability planning. The model can be run even without purchasing satellite data and GIS software, with little inaccuracy, using imagery and measurement tools provided by Google Earth.

  17. Frequency-feedback cavity enhanced spectrometer

    Science.gov (United States)

    Hovde, David Christian; Gomez, Anthony

    2015-08-18

    A spectrometer comprising an optical cavity, a light source capable of producing light at one or more wavelengths transmitted by the cavity and with the light directed at the cavity, a detector and optics positioned to collect light transmitted by the cavity, feedback electronics causing oscillation of amplitude of the optical signal on the detector at a frequency that depends on cavity losses, and a sensor measuring the oscillation frequency to determine the cavity losses.

  18. Nonlocal Intracranial Cavity Extraction

    Science.gov (United States)

    Manjón, José V.; Eskildsen, Simon F.; Coupé, Pierrick; Romero, José E.; Collins, D. Louis; Robles, Montserrat

    2014-01-01

    Automatic and accurate methods to estimate normalized regional brain volumes from MRI data are valuable tools which may help to obtain an objective diagnosis and followup of many neurological diseases. To estimate such regional brain volumes, the intracranial cavity volume (ICV) is often used for normalization. However, the high variability of brain shape and size due to normal intersubject variability, normal changes occurring over the lifespan, and abnormal changes due to disease makes the ICV estimation problem challenging. In this paper, we present a new approach to perform ICV extraction based on the use of a library of prelabeled brain images to capture the large variability of brain shapes. To this end, an improved nonlocal label fusion scheme based on BEaST technique is proposed to increase the accuracy of the ICV estimation. The proposed method is compared with recent state-of-the-art methods and the results demonstrate an improved performance both in terms of accuracy and reproducibility while maintaining a reduced computational burden. PMID:25328511

  19. Nonlocal Intracranial Cavity Extraction

    Directory of Open Access Journals (Sweden)

    José V. Manjón

    2014-01-01

    Full Text Available Automatic and accurate methods to estimate normalized regional brain volumes from MRI data are valuable tools which may help to obtain an objective diagnosis and followup of many neurological diseases. To estimate such regional brain volumes, the intracranial cavity volume (ICV is often used for normalization. However, the high variability of brain shape and size due to normal intersubject variability, normal changes occurring over the lifespan, and abnormal changes due to disease makes the ICV estimation problem challenging. In this paper, we present a new approach to perform ICV extraction based on the use of a library of prelabeled brain images to capture the large variability of brain shapes. To this end, an improved nonlocal label fusion scheme based on BEaST technique is proposed to increase the accuracy of the ICV estimation. The proposed method is compared with recent state-of-the-art methods and the results demonstrate an improved performance both in terms of accuracy and reproducibility while maintaining a reduced computational burden.

  20. Photons in a spherical cavity

    International Nuclear Information System (INIS)

    Ionescu-Pallas, N.; Vlad, V.I.

    1999-01-01

    The spectrum of black body radiation at the absolute temperature T, in an ideal spherical cavity of radius R, is studied. The departures from the classical predictions of Planck's theory, due to the discrete energies of the radiation quanta confined inside the cavity, depend on the adiabatic invariant RT and are significant for RT≤ 1 cm K. Special attention was paid to evidence sudden changes in the spectrum intensities, forbidden bands of frequency, as well as major modifications of the total energy for RT≤ 1 cm K. Similar effects were present in case of a cubic cavity too. (authors)

  1. Pseudo LRM waveforms from CryoSat SARin acquisition

    Science.gov (United States)

    Scagliola, Michele; Fornari, Marco; Bouffard, Jerome; Parrinello, Tommaso; Féménias, Pierre

    2016-04-01

    CryoSat was launched on the 8th April 2010 and is the first European ice mission dedicated to the monitoring of precise changes in the thickness of polar ice sheets and floating sea ice. The main payload of CryoSat is a Ku-band pulsewidth limited radar altimeter, called SIRAL (Synthetic interferometric radar altimeter). When commanded in SARIn (synthetic aperture radar interferometry) mode, through coherent along-track processing of the returns received from two antennas, the interferometric phase related to the first arrival of the echo is used to retrieve the angle of arrival of the scattering in the across-track direction. When SIRAL operates in SAR or SARin mode, the obtained waveforms have an along-track resolution and a speckle reduction which is increased with respect to the pulse-limited waveforms. Anyway, in order to analyze the continuity of the geophysical retrieved parameters among different acquisition modes, techniques to transform SARin mode data to pseudo-LRM mode data are welcome. The transformation process is known as SAR reduction and it is worth recalling here that only approximate pseudo-LRM waveforms can be obtained in case of closed burst acquisitions, as SIRAL operates. A SAR reduction processing scheme has been developed to obtain pseudo-LRM waveforms from CryoSat SARin acquisition. As a trade-off between the along-track length on Earth surface contributing to one SARin pseudo-LRM waveform and the noisiness of the waveform itself, it has been chosen a SAR reduction approach based on the averaging of all the SARin echoes received each 20Hz, resulting in one pseudo-LRM waveform for each SARin burst given the SARin burst repetition period. SARin pseudo-LRM waveforms have been produced for CryoSat acquisition both on ice and sea surfaces, aiming at verifying the continuity of the retracked surface height over the ellipsoid between genuine LRM products and pseudo-LRM products. Moreover, the retracked height from the SARin pseudo-LRM has been

  2. Pseudo Landau levels and quantum oscillations in strained Weyl semimetals

    Science.gov (United States)

    Alisultanov, Z. Z.

    2018-05-01

    The crystal lattice deformation in Weyl materials where the two chiralities are separated in momentum space leads to the appearance of gauge pseudo-fields. We investigated the pseudo-magnetic field induced quantum oscillations in strained Weyl semimetal (WSM). In contrast to all previous works on this problem, we use here a more general tilted Hamiltonian. Such Hamiltonian, seems to be is more suitable for a strained WSMs. We have shown that a pseudo-magnetic field induced magnetization of strained WSM is nonzero due to the fact that electric field (gradient of the deformation potential) is induced simultaneously with the pseudo-magnetic field. This related with fact that the pseudo Landau levels (LLs) in strained WSM are differ in vicinities of different WPs due to the presence of tilt in spectrum. Such violation of the equivalence between Weyl points (WPs) leads to modulation of quantum oscillations. We also showed that magnetization magnitude can be changed by application of an external electric field. In particular, it can be reduced to zero. The possibility of controlling of the magnetization by an electric field is interesting both from a fundamental point of view (a new type of magneto-electric effect) and application point of view (additional possibility to control diamagnetism of deformed WSMs). Finally, a coexistence of type-I and type-II Weyl fermions is possible in the system under investigation. Such phase is absolutely new for physics of topological systems.

  3. Pseudo Steady-State Free Precession for MR-Fingerprinting.

    Science.gov (United States)

    Assländer, Jakob; Glaser, Steffen J; Hennig, Jürgen

    2017-03-01

    This article discusses the signal behavior in the case the flip angle in steady-state free precession sequences is continuously varied as suggested for MR-fingerprinting sequences. Flip angle variations prevent the establishment of a steady state and introduce instabilities regarding to magnetic field inhomogeneities and intravoxel dephasing. We show how a pseudo steady state can be achieved, which restores the spin echo nature of steady-state free precession. Based on geometrical considerations, relationships between the flip angle, repetition and echo time are derived that suffice to the establishment of a pseudo steady state. The theory is tested with Bloch simulations as well as phantom and in vivo experiments. A typical steady-state free precession passband can be restored with the proposed conditions. The stability of the pseudo steady state is demonstrated by comparing the evolution of the signal of a single isochromat to one resulting from a spin ensemble. As confirmed by experiments, magnetization in a pseudo steady state can be described with fewer degrees of freedom compared to the original fingerprinting and the pseudo steady state results in more reliable parameter maps. The proposed conditions restore the spin-echo-like signal behavior typical for steady-state free precession in fingerprinting sequences, making this approach more robust to B 0 variations. Magn Reson Med 77:1151-1161, 2017. © 2016 International Society for Magnetic Resonance in Medicine. © 2016 International Society for Magnetic Resonance in Medicine.

  4. Pseudo-Newtonian planar circular restricted 3-body problem

    International Nuclear Information System (INIS)

    Dubeibe, F.L.; Lora-Clavijo, F.D.; González, Guillermo A.

    2017-01-01

    We study the dynamics of the planar circular restricted three-body problem in the context of a pseudo-Newtonian approximation. By using the Fodor–Hoenselaers–Perjés procedure, we perform an expansion in the mass potential of a static massive spherical source up to the first non-Newtonian term, giving place to a gravitational potential that includes first-order general relativistic effects. With this result, we model a system composed by two pseudo-Newtonian primaries describing circular orbits around their common center of mass, and a test particle orbiting the system in the equatorial plane. The dynamics of the new system of equations is studied in terms of the Poincaré section method and the Lyapunov exponents, where the introduction of a new parameter ϵ, allows us to observe the transition from the Newtonian to the pseudo-Newtonian regime. We show that when the Jacobian constant is fixed, a chaotic orbit in the Newtonian regime can be either chaotic or regular in the pseudo-Newtonian approach. As a general result, we find that most of the pseudo-Newtonian configurations are less stable than their Newtonian equivalent.

  5. Pseudo-Newtonian planar circular restricted 3-body problem

    Energy Technology Data Exchange (ETDEWEB)

    Dubeibe, F.L., E-mail: fldubeibem@unal.edu.co [Facultad de Ciencias Humanas y de la Educación, Universidad de los Llanos, Villavicencio (Colombia); Grupo de Investigación en Relatividad y Gravitación, Escuela de Física, Universidad Industrial de Santander, A.A. 678, Bucaramanga (Colombia); Lora-Clavijo, F.D., E-mail: fadulora@uis.edu.co [Grupo de Investigación en Relatividad y Gravitación, Escuela de Física, Universidad Industrial de Santander, A.A. 678, Bucaramanga (Colombia); González, Guillermo A., E-mail: guillermo.gonzalez@saber.uis.edu.co [Grupo de Investigación en Relatividad y Gravitación, Escuela de Física, Universidad Industrial de Santander, A.A. 678, Bucaramanga (Colombia)

    2017-02-12

    We study the dynamics of the planar circular restricted three-body problem in the context of a pseudo-Newtonian approximation. By using the Fodor–Hoenselaers–Perjés procedure, we perform an expansion in the mass potential of a static massive spherical source up to the first non-Newtonian term, giving place to a gravitational potential that includes first-order general relativistic effects. With this result, we model a system composed by two pseudo-Newtonian primaries describing circular orbits around their common center of mass, and a test particle orbiting the system in the equatorial plane. The dynamics of the new system of equations is studied in terms of the Poincaré section method and the Lyapunov exponents, where the introduction of a new parameter ϵ, allows us to observe the transition from the Newtonian to the pseudo-Newtonian regime. We show that when the Jacobian constant is fixed, a chaotic orbit in the Newtonian regime can be either chaotic or regular in the pseudo-Newtonian approach. As a general result, we find that most of the pseudo-Newtonian configurations are less stable than their Newtonian equivalent.

  6. Brain MR image segmentation using NAMS in pseudo-color.

    Science.gov (United States)

    Li, Hua; Chen, Chuanbo; Fang, Shaohong; Zhao, Shengrong

    2017-12-01

    Image segmentation plays a crucial role in various biomedical applications. In general, the segmentation of brain Magnetic Resonance (MR) images is mainly used to represent the image with several homogeneous regions instead of pixels for surgical analyzing and planning. This paper proposes a new approach for segmenting MR brain images by using pseudo-color based segmentation with Non-symmetry and Anti-packing Model with Squares (NAMS). First of all, the NAMS model is presented. The model can represent the image with sub-patterns to keep the image content and largely reduce the data redundancy. Second, the key idea is proposed that convert the original gray-scale brain MR image into a pseudo-colored image and then segment the pseudo-colored image with NAMS model. The pseudo-colored image can enhance the color contrast in different tissues in brain MR images, which can improve the precision of segmentation as well as directly visual perceptional distinction. Experimental results indicate that compared with other brain MR image segmentation methods, the proposed NAMS based pseudo-color segmentation method performs more excellent in not only segmenting precisely but also saving storage.

  7. Linearized pseudo-Einstein equations on the Heisenberg group

    Science.gov (United States)

    Barletta, Elisabetta; Dragomir, Sorin; Jacobowitz, Howard

    2017-02-01

    We study the pseudo-Einstein equation R11bar = 0 on the Heisenberg group H1 = C × R. We consider first order perturbations θɛ =θ0 + ɛ θ and linearize the pseudo-Einstein equation about θ0 (the canonical Tanaka-Webster flat contact form on H1 thought of as a strictly pseudoconvex CR manifold). If θ =e2uθ0 the linearized pseudo-Einstein equation is Δb u - 4 | Lu|2 = 0 where Δb is the sublaplacian of (H1 ,θ0) and L bar is the Lewy operator. We solve the linearized pseudo-Einstein equation on a bounded domain Ω ⊂H1 by applying subelliptic theory i.e. existence and regularity results for weak subelliptic harmonic maps. We determine a solution u to the linearized pseudo-Einstein equation, possessing Heisenberg spherical symmetry, and such that u(x) → - ∞ as | x | → + ∞.

  8. Reconstruction of the inner structure of small scale mining waste dumps by combining GPR and ERTdata.

    Science.gov (United States)

    Kniess, Rudolf; Martin, Tina

    2015-04-01

    Two abandoned small waste dumps in the west of the Harz mountains (Germany) were analysed using ground penetrating radar (GPR) and electrical resistivity tomography (ERT). Aim of the project (ROBEHA, funded by the German Federal Ministry of Education and Research (033R105)) is the assessment of the recycling potential of the mining residues taking into account environmental risks of reworking the dump site. One task of the geophysical prospection is the investigation of the inner structure of the mining dump. This is important for the estimation of the approximate volume of potentially reusable mining deposits within the waste dump. The two investigated dump sites are different in age and therefore differ in their structure. The older residues (mining dumps. The resistivities of the dumped material differ from the bedrock resistivities at both sites. The GPR measurements show near surface layer boundaries down to 3 - 4 m. In consecutive campaigns 100 MHz and 200 MHz antennas were used. The GPR results (layer boundaries) were included into the ERT inversion algorithm to enable more precise and stable resistivity models. This needs some special preprocessing steps. The 3D-Position of every electrode from ERT measurement and the GPR antenna position on the surface require an accuracy of less than 1cm. At some points, the layer boundaries and radar wave velocities can be calibrated with borehole stratigraphic data from a mineralogical drilling campaign. This is important for a precise time-depth conversion of reflectors from GPR measurement. This reflectors were taken from radargram and have been adopted as resistivity boundary in the start model of the geoelectric inversion algorithm.

  9. A summary of the test procedures and operational details of an ocean dumping pollution monitoring experiment conducted 7 October 1976

    Science.gov (United States)

    Hypes, W. D.; Wallace, J. W.; Gurganus, E. A.

    1977-01-01

    A remote sensor experiment was conducted at a sewage sludge dump site off the Delaware/Maryland coast. Two aircraft serving as remote sensor platforms flew over the dump site during a sludge dump. One aircraft carried a multispectral scanner and the other aircraft carried a rapid scanning spectrometer. Data from sea-truth stations were collected concurrent with overpasses of the aircraft. All sensors were operational and produced good digital data.

  10. Distribution, ecology and inhibition of Thiobacillus ferrooxidans in relation to acid drainage from Witwatersrand gold mine dumps

    International Nuclear Information System (INIS)

    Whillier, P.A.

    1987-03-01

    The distribution and ecology of Thiobacillus ferrooxidans in gold mine dumps and possible means for its inhibition were investigated. A literature survey of the micro-ecology of mine waste dumps in various parts of the world was undertaken. A linear alkylbenzene sulphonate (LAS), NANSA 80/S, and a cetyl pyridinium chloride, Ceepryn, were tested as possible inhibitors for mine dump application. The LAS was rejected because it is poorly soluble in water and required higher concentrations than SLS for the inhibition of T.ferrooxidans. Ceepryn was an efficient inhibitor, but its efficiency was dramatically impeded in the presence of mine dump sand making it unsuitable for application on dumps. The SLS and LAS were tested against a mixed population of T.ferrooxidans from gold mine dumps and these bacteria were shown to be marginally more resistant to the inhibitors than the pure T.ferrooxidans culture. Sampling from mine dumps on the Witwatersrand suggested that the major T.ferrooxidans populations occurred in the moist sand of the drainage areas at the base of dumps, with few viable iron-oxidising bacteria located on the surfaces or in the centre of dumps. Sites of low moisture in dumps contained few or no viable bacteria. In the laboratory the bacterial viability decreased rapidly with loss of moisture from the sand. Moisture was shown to be important to bacterial activity and should be considered with respect to acid drainage control. Experimental sand columns showed that iron was leached with water from mine dump sand in the absence and presence of bacteria. In this study substrates, moisture, oxygen and carbon dioxide availability, ph, temperature, microorganisms and metal pollutants of uranium waste dumps are also covered

  11. Cavity and goaf control

    Energy Technology Data Exchange (ETDEWEB)

    Stassen, P

    1978-01-01

    A summary of stowing, including a definition, calculation of stowing material requirements and settling of packs is given. A) Stowing using dirt found locally - the dirt bands in the seam - the use of ripping dirt brought down by the scraper loader and used for packing purposes and the construction of dummy roads. B) Control of cavities by leaving short, thick props and timber chocks in place. C) Stowing methods involving imported firt: packing by hand, use of scraper loaders, slinger stowing and control led-gravity stowing. D) Pneumatic stowing: describes the various types of machine and their scope; pipelines, their installation and cost price; pneumatic stowing in conjunc tion with powered supports; the use of crusher-stowers for stowing ripping dirt; construction of anhydrite packs by means of a pneumatic stower. E) Hydraulic stowing: how it works, the materials involved, utilization conditions, the surface storage post, pipes, stoppings with stowed material, water removal, rates of hydraulic stowing, results of theoretical studies, and the use of hydraulic stowing in the metal-mines. F) Pumped packs: how they work, how the packs are installed, the strength of the packs and their various uses. G) Caving: describes the principle of caving, support patterns, caving with packs and makes a comparison between caving and stowing. H) Comparison between the various methods of stowing compares pneumatic with hydraulic stowing methods; compares packing by hand and mechanical stowing compares surface subsidence in terms of the method of goaf used underground. An appendix gives details of equipment used. (15 refs.) (In French)

  12. Loggerhead oral cavity morphometry study

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Standard external morphometrics and internal oral cavity morphometrics data were collected on wild and captive reared loggerhead sea turtles in size classes ranging...

  13. Niobium LEP 2 accelerating cavities

    CERN Multimedia

    An accelerating cavity from LEP. This could be cut open to show the layer of niobium on the inside. Operating at 4.2 degrees above absolute zero, the niobium is superconducting and carries an accelerating field of 6 million volts per metre with negligible losses. Each cavity has a surface of 6 m2. The niobium layer is only 1.2 microns thick, ten times thinner than a hair. Such a large area had never been coated to such a high accuracy. A speck of dust could ruin the performance of the whole cavity so the work had to be done in an extremely clean environment. These challenging requirements pushed European industry to new achievements. 256 of these cavities were used in an upgrade of the LEP accelerator to double the energy of the particle beams.

  14. Bistability of Cavity Magnon Polaritons

    Science.gov (United States)

    Wang, Yi-Pu; Zhang, Guo-Qiang; Zhang, Dengke; Li, Tie-Fu; Hu, C.-M.; You, J. Q.

    2018-01-01

    We report the first observation of the magnon-polariton bistability in a cavity magnonics system consisting of cavity photons strongly interacting with the magnons in a small yttrium iron garnet (YIG) sphere. The bistable behaviors emerged as sharp frequency switchings of the cavity magnon polaritons (CMPs) and related to the transition between states with large and small numbers of polaritons. In our experiment, we align, respectively, the [100] and [110] crystallographic axes of the YIG sphere parallel to the static magnetic field and find very different bistable behaviors (e.g., clockwise and counter-clockwise hysteresis loops) in these two cases. The experimental results are well fitted and explained as being due to the Kerr nonlinearity with either a positive or negative coefficient. Moreover, when the magnetic field is tuned away from the anticrossing point of CMPs, we observe simultaneous bistability of both magnons and cavity photons by applying a drive field on the lower branch.

  15. Design of rf conditioner cavities

    International Nuclear Information System (INIS)

    Govil, R.; Rimmer, R.A.; Sessler, A.; Kirk, H.G.

    1992-06-01

    Theoretical studies are made of radio frequency structures which can be used to condition electron beams so as to greatly reduce the stringent emittance requirements for successful lasing in a free-electron laser. The basic strategy of conditioning calls for modulating an electron beam in the transverse dimension, by a periodic focusing channel, while it traverses a series of rf cavities, each operating in a TM 210 mode. In this paper, we analyze the cavities both analytically and numerically (using MAFIA simulations). We find that when cylindrical symmetry is broken the coupling impedance can be greatly enhanced. We present results showing various performance characteristics as a function of cavity parameters, as well as possible designs for conditioning cavities

  16. SRF Cavity Fabrication and Materials

    CERN Document Server

    Singer, W

    2014-07-17

    The technological and metallurgical requirements of material for highgradient superconducting cavities are described. High-purity niobium, as the preferred metal for the fabrication of superconducting accelerating cavities, should meet exact specifications. The content of interstitial impurities such as oxygen, nitrogen, and carbon must be below 10μg/g. The hydrogen content should be kept below 2μg/g to prevent degradation of the Q-value under certain cool-down conditions. The material should be free of flaws (foreign material inclusions or cracks and laminations) that can initiate a thermal breakdown. Defects may be detected by quality control methods such as eddy current scanning and identified by a number of special methods. Conventional and alternative cavity fabrication methods are reviewed. Conventionally, niobium cavities are fabricated from sheet niobium by the formation of half-cells by deep drawing, followed by trim machining and Electron-Beam Welding (EBW). The welding of half-cells is a delicate...

  17. On the Relativistic Origin of Pseudo spin Symmetry in Nuclei

    International Nuclear Information System (INIS)

    Leviatan, A.

    1998-01-01

    We review the concept of pseudo spin symmetry and its role in nuclear spectroscopy. We survey the attempts to arrive at a microscopic understanding of this symmetry. In particular, we show that pseudo spin symmetry in nuclei could arise from nucleons moving in a relativistic mean field which has an attractive scalar (Vs) and repulsive vector (Vv) potential nearly equal in magnitude but opposite in sign. We show that the generators of pseudo spin symmetry are the non-relativistic limit of the generators of an SU(2) symmetry which leaves invariant the Dirac Hamiltonian with Vs 2= -Vv. Furthermore within this framework, we demonstrate that this symmetry may be approximately conserved for realistic scalar and vector potentials

  18. Inflammatory pseudo tumor of the spleen. Radiologic findings

    International Nuclear Information System (INIS)

    Folgueral, M.; Naranjo, G.; Grasa, J.

    1998-01-01

    The inflammatory splenic pseudo tumor is an uncommon benign lesion of unknown etiology that usually is detected incidentally in patients being examined for other disorders. We present the ultrasound, computed tomography (CT) and magnetic resonance (MR) findings in two patients (a 56-year-old woman and 67-year-old man) with inflammatory pseudo tumor of the spleen. Ultrasound images of the inflammatory splenic pseudo tumor show a hypoechoic mass with or without calcifications. In CT, the mass presents a low attenuation that is slightly enhanced by intravenous injection of an iodinated contrast medium. MR images show an isointense spleen in T1-weighted spin-echo sequences that is hypointense in T2-weighted sequences. The differential diagnosis should consider other more common splenic masses. but the definitive diagnosis can not be based on imaging methods alone. In the both cases, the final diagnosis was reached after splenectomy and pathological study. (Author) 8 refs

  19. Pseudo-Glassification Material for G-Demption

    Energy Technology Data Exchange (ETDEWEB)

    Casella, Andrew M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Buck, Edgar C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gates, Robert O. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Riley, Brian J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2014-09-01

    G-Demption, LLC has requested that PPNL provide design input for a “pseudo-glassification” process associated with their proposed technology for generating gamma irradiation stations from used nuclear fuel. The irradiation design currently consists of an aluminum enclosure designed to allow for proper encapsulation of and heat flow from a used fuel rod while minimally impacting the streaming of gamma rays from the fuel. In order to make their design more robust, G-Demption is investigating the benefits of backfilling this aluminum enclosure with a setting material once the used fuel rod is properly placed. This process has been initially referred to as “pseudo-glassification”, and strives not to impact heat transport or gamma streaming from the used fuel rod while providing increased fuel rod protection and fission gas retention. PNNL has compiled an internal material evaluation and discussion for the “pseudo-glassification” process in this report.

  20. Electron with arbitrary pseudo-spins in multilayer graphene

    International Nuclear Information System (INIS)

    Prarokijjak Worasak; Soodchomshom Bumned

    2015-01-01

    Using the low-energy effective Hamiltonian of the ABC-stacked multilayer graphene, the pseudo-spin coupling to real orbital angular momentum of electrons in multilayer graphene is investigated. We show that the electron wave function in N-layer graphene mimics the behavior of a particle with a spin of N × (ħ/2), where N = {1, 2, 3,…}. It is said that for N > 1 the low-energy effective Hamiltonian for ABC-stacked graphene cannot be used to describe pseudo-spin-1/2 particles. The wave function of electrons in multilayer graphene may behave like fermionic (or bosonic) particle for N being odd (or even). In this paper, we propose a theory of graphene serving as a host material of electrons with arbitrary pseudo-spins tunable by changing the number of graphene layers. (paper)

  1. Electron with arbitrary pseudo-spins in multilayer graphene

    Institute of Scientific and Technical Information of China (English)

    Worasak Prarokijjak; Bumned Soodchomshom

    2015-01-01

    Using the low-energy effective Hamiltonian of the ABC-stacked multilayer graphene, the pseudo-spin coupling to real orbital angular momentum of electrons in multilayer graphene is investigated. We show that the electron wave function in N-layer graphene mimics the behavior of a particle with a spin of N × (}/2), where N={1, 2, 3, . . .}. It is said that for N>1 the low-energy effective Hamiltonian for ABC-stacked graphene cannot be used to describe pseudo-spin-1/2 particles. The wave function of electrons in multilayer graphene may behave like fermionic (or bosonic) particle for N being odd (or even). In this paper, we propose a theory of graphene serving as a host material of electrons with arbitrary pseudo-spins tunable by changing the number of graphene layers.

  2. Episodic seasonal Pseudo-Bartter syndrome in cystic fibrosis.

    Science.gov (United States)

    Kintu, Brett; Brightwell, Alex

    2014-06-01

    Pseudo-Bartter syndrome (PBS) describes an uncommon but well recognised complication of cystic fibrosis leading to hypochloraemic, hypokalaemic metabolic alkalosis. Pseudo-Bartter syndrome is usually seen at initial presentation or within the first two years of life in children with cystic fibrosis. Risk factors for development of PBS include warm weather conditions, severe respiratory or pancreatic disease and gastrointestinal losses (e.g. vomiting and diarrhoea). PBS is rare in older children and adolescents although epidemics have been associated with heat wave conditions in warmer climates. In this era of climate change, it is crucial that clinicians consider Pseudo-Bartter syndrome when patients with cystic fibrosis present unwell during summer. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. Phenomenology of a pseudo-scalar inflaton: naturally large nongaussianity

    International Nuclear Information System (INIS)

    Barnaby, Neil; Namba, Ryo; Peloso, Marco

    2011-01-01

    Many controlled realizations of chaotic inflation employ pseudo-scalar axions. Pseudo-scalars φ are naturally coupled to gauge fields through cφF F-tilde . In the presence of this coupling, gauge field quanta are copiously produced by the rolling inflaton. The produced gauge quanta, in turn, source inflaton fluctuations via inverse decay. These new cosmological perturbations add incoherently with the ''vacuum'' perturbations, and are highly nongaussian. This provides a natural mechanism to generate large nongaussianity in single or multi field slow-roll inflation. The resulting phenomenological signatures are highly distinctive: large nongaussianity of (nearly) equilateral shape, in addition to detectably large values of both the scalar spectral tilt and tensor-to-scalar ratio (both being typical of large field inflation). The WMAP bound on nongaussianity implies that the coupling c of the pseudo-scalar inflaton to any gauge field must be smaller than about 10 2 M p −1

  4. Pseudo-periodic maps and degeneration of Riemann surfaces

    CERN Document Server

    Matsumoto, Yukio

    2011-01-01

    The first part of the book studies pseudo-periodic maps of a closed surface of genus greater than or equal to two. This class of homeomorphisms was originally introduced by J. Nielsen in 1944 as an extension of periodic maps. In this book, the conjugacy classes of the (chiral) pseudo-periodic mapping classes are completely classified, and Nielsen’s incomplete classification is corrected. The second part applies the results of the first part to the topology of degeneration of Riemann surfaces. It is shown that the set of topological types of all the singular fibers appearing in one-parameter holomorphic families of Riemann surfaces is in a bijective correspondence with the set of conjugacy classes of the pseudo-periodic maps of negative twists. The correspondence is given by the topological monodromy.

  5. LEP Radio Frequency Copper Cavity

    CERN Multimedia

    The pulse of a particle accelerator. 128 of these radio frequency cavities were positioned around CERN's 27-kilometre LEP ring to accelerate electrons and positrons. The acceleration was produced by microwave electric oscillations at 352 MHz. The electrons and positrons were grouped into bunches, like beads on a string, and the copper sphere at the top stored the microwave energy between the passage of individual bunches. This made for valuable energy savings as it reduced the heat generated in the cavity.

  6. TESLA superconducting RF cavity development

    International Nuclear Information System (INIS)

    Koepke, K.

    1995-01-01

    The TESLA collaboration has made steady progress since its first official meeting at Cornell in 1990. The infrastructure necessary to assemble and test superconducting rf cavities has been installed at the TESLA Test Facility (TTF) at DESY. 5-cell, 1.3 GHz cavities have been fabricated and have reached accelerating fields of 25 MV/m. Full sized 9-cell copper cavities of TESLA geometry have been measured to verify the higher order modes present and to evaluate HOM coupling designs. The design of the TESLA 9-cell cavity has been finalized and industry has started delivery. Two prototype 9-cell niobium cavities in their first tests have reached accelerating fields of 10 MV/m and 15 MV/m in a vertical dewar after high peak power (HPP) conditioning. The first 12 m TESLA cryomodule that will house 8 9-cell cavities is scheduled to be delivered in Spring 1995. A design report for the TTF is in progress. The TTF test linac is scheduled to be commissioned in 1996/1997. (orig.)

  7. Influence of dump voltage and allowable temperature rise on stabilizer requirements in superconducting coils

    International Nuclear Information System (INIS)

    Schwenterly, S.W.

    1988-01-01

    A superconducting winding must have enough stabilizer to satisfy two sets of criteria. During normal operation, the amount of stabilizer must be large enough either to make the coil unconditionally stable or to give a certain desired stability margin. Once a dump occurs, the amount of stabilizer must be large enough to carry the current without generating excessive dump voltages or allowing the winding to exceed a certain maximum temperature (and maximum pressure, in the case of force-cooled coils). The voltage criterion often dominates for very large coil systems, but it is frequently ignored in initial design studies. This paper gives some simple relations between the dump voltage and the stored energy, temperature rise, and coil geometry that are useful in scooping the required amount of stabilizer. Comparison with some recently proposed fusion magnet system designs indicates that excessive dump voltages could result in some cases. High-temperature superconductors may require more stabilizer than the conventional alloys. Calculations with simple model coil systems indicate how trade-offs between various coil parameters affect the dump voltage. 12 refs., 1 fig., 1 tab

  8. Thermal, mechanical and fluid flow aspects of the high power beam dump for FRIB

    Energy Technology Data Exchange (ETDEWEB)

    Avilov, Mikhail [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States); Aaron, Adam [Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831 (United States); Amroussia, Aida [Department of Chemical Engineering and Materials Science, Michigan State University, East Lansing, MI 48824 (United States); Bergez, Wladimir [Institut de Mecanique des Fluides de Toulouse, Toulouse University, CNRS, Allée Camille Soula, 31400 Toulouse (France); Boehlert, Carl [Department of Chemical Engineering and Materials Science, Michigan State University, East Lansing, MI 48824 (United States); Burgess, Thomas; Carroll, Adam [Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831 (United States); Colin, Catherine [Institut de Mecanique des Fluides de Toulouse, Toulouse University, CNRS, Allée Camille Soula, 31400 Toulouse (France); Durantel, Florent [Centre des recherches sur les Ions, les Materiaux et la Photonique (CIMAP) CEA-CNRS-ENSICAEN-UCN, BP 5133, 14070 CAEN CEDEX 5 (France); Ferrante, Paride; Fourmeau, Tiffany [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States); Graves, Van [Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831 (United States); Grygiel, Clara [Centre des recherches sur les Ions, les Materiaux et la Photonique (CIMAP) CEA-CNRS-ENSICAEN-UCN, BP 5133, 14070 CAEN CEDEX 5 (France); Kramer, Jacob [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States); Mittig, Wolfgang [National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States); Monnet, Isabelle [Centre des recherches sur les Ions, les Materiaux et la Photonique (CIMAP) CEA-CNRS-ENSICAEN-UCN, BP 5133, 14070 CAEN CEDEX 5 (France); Patel, Harsh [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States); and others

    2016-06-01

    The Facility for Rare Isotope Beams (FRIB) under construction at Michigan State University is based on a 400 kW heavy ion accelerator and uses in-flight production and separation to generate rare isotope beams. The first section of the fragment separator houses the rare isotope production target, and the primary beam dump to stop the unreacted primary beam. The experimental program will use 400 kW ion beams from {sup 16}O to {sup 238}U. After interaction with the production target, over 300 kW in remaining beam power must be absorbed by the beam dump. A rotating water-cooled thin-shell metal drum was chosen as the basic concept for the beam dump. Extensive thermal, mechanical and fluid flow analyses were performed to evaluate the effects of the high power density in the beam dump shell and in the water. Many properties were optimized simultaneously, such as shell temperature, mechanical strength, fatigue strength, and radiation resistance. Results of the analyses of the beam dump performance with different design options will be discussed. For example, it was found that a design modification to the initial water flow pattern resulted in a substantial increase in the wall heat transfer coefficient. A detailed evaluation of materials for the shell is in progress. The widely used titanium alloy, Ti–6Al–4V (wt%), is presently considered as the best candidate, and is the subject of specific tests, such as studies of performance under heavy ion irradiation.

  9. Radionuclides and toxic elements transfer from the princess dump to water in Roodepoort, South Africa.

    Science.gov (United States)

    Dlamini, S G; Mathuthu, M M; Tshivhase, V M

    2016-03-01

    High concentrations of radionuclides and toxic elements in gold mine tailings facilities present a health hazard to the environment and people living near that area. Soil and water samples from selected areas around the Princess Mine dump were collected. Soil sampling was done on the surface (15 cm) and also 100 cm below the surface. Water samples were taken from near the dump, mid-stream and the flowing part of the stream (drainage pipe) passing through Roodepoort from the mine dump. Soil samples were analyzed by gamma-ray spectroscopy using a HPGe detector to determine the activity concentrations of (238)U, (232)Th and (4) (​40)K from the activities of the daughter nuclides in the respective decay chains. The average activity concentrations for uranium and thorium in soil were calculated to be 129 ± 36.1 Bq/kg and 18.1 ± 4.01 Bq/kg, respectively. Water samples were analyzed using Inductively Coupled Plasma Mass Spectrometer. Transfer factors for uranium and thorium from soil to water (at point A closest to dump) were calculated to be 0.494 and 0.039, respectively. At point Z2, which is furthest from the dump, they were calculated to be 0.121 and 0.004, respectively. These transfer factors indicate that there is less translocation of the radionuclides as the water flows. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Optimizing Dredge-and-Dump Activities for River Navigability Using a Hydro-Morphodynamic Model

    Directory of Open Access Journals (Sweden)

    Andries J. Paarlberg

    2015-07-01

    Full Text Available Worldwide, significant dredging activities of riverbed sediment are employed to ensure that freight transportation on rivers can continue year-round. Imbalances of sediment budget may produce relevant impacts regarding river morphology and related environmental services. This study shows that hydro-morphodynamic modeling tools can be used to optimize dredge-and-dump activities and, at the same time, mitigate problems deriving from these activities in rivers. As a case study, we focused on dredging activities on the Lower Parana River, Argentina. Navigation on this river is of crucial importance to the economies of the bordering countries, hence, each year significant dredging activities are employed. To estimate dredging loads under different strategies, a 25 km river reach of the Parana River was modeled using the Delft3D-modelling suite by Deltares. The Netherlands, to simulate flow-sediment interactions in a quasi-steady and uncoupled approach. Impacts of dredging activities were explicitly included. Different dredge-and-dump strategies included variations in dredging over-depth (clearance and variations in dumping locations. Our results indicate that dredge-and-dump strategies can be targeted to stimulate natural processes that improve the depth and stability of the navigation channel and to counteract unwanted bed level responses in the long-medium term. A ~40% reduction in dredging effort could be achieved by moving the dredged material to distant locations in the secondary channel rather than dumping to the side of the waterway in the main channel.

  11. Conceptual design of Dump resistor for Superconducting CS of SST-1

    Science.gov (United States)

    Roy, Swati; Raj, Piyush; Panchal, Arun; Pradhan, Subrata

    2017-04-01

    Under upgradation activities for SST-1, the existing resistive central solenoid (CS) coil will be replaced with Nb3Sn based superconducting coil. Design of Central solenoid had been completed and some of the initiative has already taken for its manufacturing. The superconducting CS will store upto 3 MJ of magnetic energy per operation cycle with operating current upto 14 kA. During quench, energy stored in the coils has to be extracted rapidly with a time constant of 1.5 s by inserting a 20 mΩ dump resistor in series with the superconducting CS which is normally shorted by circuit breakers. As a critical part of the superconducting CS quench protection system, a conceptual design of the 20 mΩ dump resistor has been proposed. The required design aspects and a dimensional layout of the dump resistor for the new superconducting CS has been presented and discussed. The basic structure of the proposed dump resistor comprises of stainless steel grids connected in series in the form of meander to minimize the stray inductance and increase the surface area for cooling. Such an array of grids connected in series and parallel will cater to the electrical as well as thermal parameters. It will be cooled by natural convection. During operation, the estimated maximum temperature of the proposed dump resistor will raise upto 600 K.

  12. First Operational Experience with the LHC Beam Dump Trigger Synchronisation Unit

    CERN Document Server

    Antoine, A; Magnin, N; Juteau, P; Voumard, N

    2011-01-01

    Two LHC Beam Dumping Systems (LBDS) remove the counter-rotating beams safely from the collider during setting up of the accelerator, at the end of a physics run and in case of emergencies. Dump requests can come from 3 different sources: the machine protection system in emergency cases, the machine timing system for scheduled dumps or the LBDS itself in case of internal failures. These dump requests are synchronized with the 3 μs beam abort gap in a fail-safe redundant Trigger Synchronization Unit (TSU) based on a Digital Phase Locked Loop (DPLL), locked onto the LHC beam revolution frequency with a maximum phase error of 40 ns. The synchronized trigger pulses coming out of the TSU are then distributed to the high voltage generators of the beam dump kickers through a redundant fault-tolerant trigger distribution system. This paper describes the operational experience gained with the TSU since its commissioning with beam in 2009, and highlights the improvements, which have been implemented f...

  13. Secondary succession of nematodes in power plant ash dumps reclaimed by covering with turf

    Energy Technology Data Exchange (ETDEWEB)

    Dmowska, E.; Ilieva-Makulec, K. [Polish Academy of Science, Lomianki (Poland)

    2006-11-15

    An analysis of successive changes in nematode assemblages in reclaimed waste area offers information about the sensitivity of species or groups of nematodes to specific conditions and ability to colonise new habitats. The study was carried in ash dumps being a by-product of the combustion of hard coal and reclaimed by covering with mineral turf (light loam warp soil) or organic turf (alder peat). In the first 3 years of reclamation diversity of nematodes was low, especially in, the dump covered with mineral turf - Shannon diversity index below 3. Later on the value of Shannon index increased and did not differ from those recorded for meadows in Poland. In the ash dump, reclaimed for a longer time period (8-11 years), the contribution of K strategist species was higher than in the dumps reclaimed for a shorter time period (2-5 years). At the earlier stages of succession bacterivores Acrobeloides, and two fungivores Aphelenchoides and Aphelenchus, predominated. In the ash dump reclaimed longer the dominance of these three genera decreased and some plant feeders achieved high contribution ({gt} 30%). The composition of nematode communities depended. significantly on the period of reclamation, but did not depend either on the soil moisture and pH or on season.

  14. Plant species from coal mine overburden dumping site in Satui, South Kalimantan, Indonesia

    Directory of Open Access Journals (Sweden)

    Vivi Novianti

    2017-07-01

    Full Text Available Coal mine overburden (OB materials were nutrient-poor, loosely adhered particles of shale, stones, boulders, and cobbles, also contained elevated concentration of trace metals. This condition cause OB substrate did not support plants growth. However, there were certain species that able to grow on overburden dumping site. This investigation sought to identify plants species that presence on coal mine overburden. The research was conducted on opencast coal mine OB dumping site in Satui, South Kalimantan. Vegetation sampling was carried out on six different ages of coal mine OB dumps (7, 10, 11, 42, 59 and 64 month using line transect. Species identification used information from local people, AMDAL report of PT Arutmin Indonesia-Satui mine project, and website. There were 123 plant species, consisted of 79 herbs (Cyperaceae, Poaceae and Asteraceae, 10 lianes, bryophyte, 9 ferns, 10 shrubs, and 14 trees. A number of Poaceae, i.e., Paspalumconjugatum, Paspalumdilatatum, and Echinochloacolona generally present among the stones, boulders, and cobbles. While Cyperaceae such as Fimbristylis miliaceae, Cyperus javanicus, Rhyncospora corymbosa and Scleria sumatrensis most often foundinand around thebasin/pond with its smooth and humid substrate characteristics. Certain species of shrubs and trees present on the 7 month OB dumping site. They wereChromolaena odorata, Clibadium surinamense, Melastoma malabathricum, Trema micrantha, and Solanum torvum (Shrubs, Ochroma pyramidale and Homalanthus populifolius (trees. This plant species could be used for accelerating primary succession purpose on coal mine overburden dumping site. Nevertheless, species selection was needed to avoid planting invasive species.

  15. Metropolitan garbage dumps: possible winter migratory raptor monitoring stations in peninsular India

    Directory of Open Access Journals (Sweden)

    S. Pande

    2010-09-01

    Full Text Available Winter raptor migration and movement is poorly documented for peninsular India, mainly due to the lack of geographical bottlenecks. We describe, for the first time, the use of a garbage dump in a metropolitan city as an alternative visual winter raptor monitoring station. The daily count, adult to juvenile ratios and species composition of three migratory raptor species, Steppe Eagle Aquila nipalensis, Black-eared Kite Milvus migrans lineatus and Tawny Eagle Aquila rapax are presented. Ground temperatures at the garbage dump site and surrounding area, and the wing beat rate of migratory raptors before and after arrival in the early morning were measured. A total of 355 raptors migrating over a period of six observation days with 250 adults and 105 juveniles were recorded. The temperature of the garbage dump was significantly higher than the surrounding area, while the wing flapping rate was significantly lower over the garbage dump area. It is possible that migrating raptors use garbage dump thermals in the early morning to save energy with soaring and gliding flight (versus flapping flight. We propose that such sites may be used as visual winter migration monitoring stations in metropolitan cities in peninsular India.

  16. The possibility of distance methods application for snow dump sites monitoring

    Directory of Open Access Journals (Sweden)

    Pasko Olga

    2016-01-01

    Full Text Available In this article the results of remote sensing of the Earth for monitoring of four snow dump sites in Tomsk are described. Their compliance with permitted type of the territory use was evaluated. Earlier unknown time of the operation start was identified. The spatial-temporal variability of areas was defined. The temperature profiles of snow dump and background sites were analyzed. Use of remote sensing data allowed easy identification of snow dump sites creation time. The fact that the sites are located out of zones of permitted type of the territory use was revealed, that is violation of the law. For the first time the cartographic material was collected and showed that in the recent years their areas increased in average in 18%. The fore-cast for the nearest years was made. The article contains satellite images indicting the degradation of soil-vegetative cover of snow dumps. The reasons are contamination and overcooling of the soil in the beginning of vegetation period. The research results became the initial material for perfection of snow dumps territories management and will be applied in the work of environmental protecting service. Approaches proposed by authors may be used in solving similar problems in any region.

  17. Pseudo-stochastic signal characterization in wavelet-domain

    International Nuclear Information System (INIS)

    Zaytsev, Kirill I; Zhirnov, Andrei A; Alekhnovich, Valentin I; Yurchenko, Stanislav O

    2015-01-01

    In this paper we present the method for fast and accurate characterization of pseudo-stochastic signals, which contain a large number of similar but randomly-located fragments. This method allows estimating the statistical characteristics of pseudo-stochastic signal, and it is based on digital signal processing in wavelet-domain. Continuous wavelet transform and the criterion for wavelet scale power density are utilized. We are experimentally implementing this method for the purpose of sand granulometry, and we are estimating the statistical parameters of test sand fractions

  18. Pseudo Random Coins Show More Heads Than Tails

    OpenAIRE

    Bauke, Heiko; Mertens, Stephan

    2003-01-01

    Tossing a coin is the most elementary Monte Carlo experiment. In a computer the coin is replaced by a pseudo random number generator. It can be shown analytically and by exact enumerations that popular random number generators are not capable of imitating a fair coin: pseudo random coins show more heads than tails. This bias explains the empirically observed failure of some random number generators in random walk experiments. It can be traced down to the special role of the value zero in the ...

  19. Pseudo-Random Number Generator Based on Coupled Map Lattices

    Science.gov (United States)

    Lü, Huaping; Wang, Shihong; Hu, Gang

    A one-way coupled chaotic map lattice is used for generating pseudo-random numbers. It is shown that with suitable cooperative applications of both chaotic and conventional approaches, the output of the spatiotemporally chaotic system can easily meet the practical requirements of random numbers, i.e., excellent random statistical properties, long periodicity of computer realizations, and fast speed of random number generations. This pseudo-random number generator system can be used as ideal synchronous and self-synchronizing stream cipher systems for secure communications.

  20. Pollicisation: The Myth about Creating a Pseudo-Trapezium.

    Science.gov (United States)

    Mennen, Ulrich

    2018-06-01

    We have performed 14 pollicisations without creating a "pseudo-trapezium" from the metacarpal head. The entire metacarpal of the intended finger to be pollicised is removed and the proximal phalanx of the finger is inserted into the space left by the base of the excised metacarpal. The results are good to excellent in all 14 cases followed for 2-9 years. The advantages are that the operation is much simpler, thus also much quicker. The new thumb looks more like a thumb (not too long) and is more stable (ball-and-socket joint), with no long term complications often seen with the pseudo-trapezium.

  1. Enhancing Pseudo-Telepathy in the Magic Square Game

    Science.gov (United States)

    Pawela, Łukasz; Gawron, Piotr; Puchała, Zbigniew; Sładkowski, Jan

    2013-01-01

    We study the possibility of reversing an action of a quantum channel. Our principal objective is to find a specific channel that reverses as accurately as possible an action of a given quantum channel. To achieve this goal we use semidefinite programming. We show the benefits of our method using the quantum pseudo-telepathy Magic Square game with noise. Our strategy is to move the pseudo-telepathy region to higher noise values. We show that it is possible to reverse the action of a noise channel using semidefinite programming. PMID:23762246

  2. 21 CFR 872.3260 - Cavity varnish.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cavity varnish. 872.3260 Section 872.3260 Food and... DENTAL DEVICES Prosthetic Devices § 872.3260 Cavity varnish. (a) Identification. Cavity varnish is a device that consists of a compound intended to coat a prepared cavity of a tooth before insertion of...

  3. TEM observations of crack tip: cavity interactions

    International Nuclear Information System (INIS)

    Horton, J.A.; Ohr, S.M.; Jesser, W.A.

    1981-01-01

    Crack tip-cavity interactions have been studied by performing room temperature deformation experiments in a transmission electron microscope on ion-irradiated type 316 stainless steel with small helium containing cavities. Slip dislocations emitted from a crack tip cut, sheared, and thereby elongated cavities without a volume enlargement. As the crack tip approached, a cavity volume enlargement occurred. Instead of the cavities continuing to enlarge until they touch, the walls between the cavities fractured. Fracture surface dimples do not correlate in size or density with these enlarged cavities

  4. Fabrication of elliptical SRF cavities

    Science.gov (United States)

    Singer, W.

    2017-03-01

    The technological and metallurgical requirements of material for high-gradient superconducting cavities are described. High-purity niobium, as the preferred metal for the fabrication of superconducting accelerating cavities, should meet exact specifications. The content of interstitial impurities such as oxygen, nitrogen, and carbon must be below 10 μg g-1. The hydrogen content should be kept below 2 μg g-1 to prevent degradation of the quality factor (Q-value) under certain cool-down conditions. The material should be free of flaws (foreign material inclusions or cracks and laminations) that can initiate a thermal breakdown. Traditional and alternative cavity mechanical fabrication methods are reviewed. Conventionally, niobium cavities are fabricated from sheet niobium by the formation of half-cells by deep drawing, followed by trim machining and electron beam welding. The welding of half-cells is a delicate procedure, requiring intermediate cleaning steps and a careful choice of weld parameters to achieve full penetration of the joints. A challenge for a welded construction is the tight mechanical and electrical tolerances. These can be maintained by a combination of mechanical and radio-frequency measurements on half-cells and by careful tracking of weld shrinkage. The main aspects of quality assurance and quality management are mentioned. The experiences of 800 cavities produced for the European XFEL are presented. Another cavity fabrication approach is slicing discs from the ingot and producing cavities by deep drawing and electron beam welding. Accelerating gradients at the level of 35-45 MV m-1 can be achieved by applying electrochemical polishing treatment. The single-crystal option (grain boundary free) is discussed. It seems that in this case, high performance can be achieved by a simplified treatment procedure. Fabrication of the elliptical resonators from a seamless pipe as an alternative is briefly described. This technology has yielded good

  5. Hydroforming of superconducting TESLA cavities

    International Nuclear Information System (INIS)

    Singer, W.; Kaiser, H.; Singer, X.

    2003-01-01

    Seamless fabrication of single-cell and multi-cell TESLA shape cavities by hydroforming has been developed at DESY. The forming takes place by expanding the seamless tube with internal water pressure while simultaneously swaging it axially. Tube radius and axial displacement are being computer controlled in accordance with results of FEM simulations and the experimentally obtained strain-stress curve of tube material. Several Nb single cell cavities have been produced. A first bulk Nb double cell cavity has been fabricated. The Nb seamless tubes have been produced by spinning and deep drawing. Surface treatment such as buffered chemical polishing, (BCP), electropolishing (EP), high pressure ultra pure water rinsing (HPR), annealing at 800degC and baking at ca. 150degC have been applied. The best single cell bulk Nb cavity has reached an accelerating gradient of Eacc > 42 MV/m after ca. 250 μm BCP and 100 μm EP. Several bimetallic NbCu single cell cavities of TESLA shape have been fabricated. The seamless tubes have been produced by explosive bonding and subsequent flow forming. The thicknesses of Nb and Cu layers in the tube wall are about 1 mm and 3 mm respectively. The RF performance of NbCu clad cavities is similar to that of bulk Nb cavities. The highest accelerating gradient achieved was 40 MV/m after ca. 180 μm BCP, annealing at 800degC and baking at 140degC for 30 hours. The degradation of the quality factor Qo after repeated quenching is moderate, after ca. 150 quenches it reaches the saturation point of Qo=1.4x10 10 at low field. This indicates that on the basis of RF performance and material costs the combination of hydroforming with tube cladding is a very promising option. (author)

  6. Radioactivity of dumps in mining areas of the Upper Silesian Coal Basin in Poland

    Directory of Open Access Journals (Sweden)

    Dorda J.

    2012-04-01

    Full Text Available Underground coal mining is associated with large quantities of gangue. In the past, the majority of gangue was not utilized but was placed in the vicinity of the coalmines forming cone-shaped dumps. Some of them contained even millions of tons of rock. Nowadays, environmental precautions extort larger utilization of any kind of waste materials, for example in road construction, civil engineering or as stowing in underground abandoned workings. Examination of the composition of waste dumps, including radioactivity, is thus an important issue. The paper presents results of a radiological survey carried out in several dumps located in the Upper Silesian Coal Basin in the south of Poland. Measurements of samples were carried out with the use of a gamma-ray spectrometer. Activity concentration results for the uranium and thorium decay chains are discussed.

  7. STRESS LOADING SIMULATION OF HYDRO-MECHANICAL TRANSMISSION OF DUMP TRUCK

    Directory of Open Access Journals (Sweden)

    S. A. Sidorov

    2006-01-01

    Full Text Available The Transmission model and software package to investigate stress loading of a hydromechanical transmission of a dump truck have been developed. The given software package allows to model stress loading of transmission gears in taking-off and acceleration modes at various road resistance, positions of an engine control pedal and initial revolutions of an engine crankshaft, various laws of friction clutch switching and some other parameters that permit to reveal a rate of various operational mode influence on stress loading of a dump truck transmission. An equivalence of the developed software is proved by the comparison of the experimentally obtained stress loading process of the hydro-mechanical transmission of a BelAZ- 7555 dump truck with the results of the simulation 

  8. pH-dependent leaching of dump coal ash - retrospective environmental analysis

    Energy Technology Data Exchange (ETDEWEB)

    Popovic, A.; Djordjevic, D. [University of Belgrade, Belgrade (Serbia). Dept. of Chemistry

    2009-07-01

    Trace and major elements in coal ash particles from dump of 'Nikola Tesla A' power plant in Obrenovac near Belgrade (Serbia) can cause pollution, due to leaching by atmospheric and surface waters. In order to assess this leaching potential, dump ash samples were subjected to extraction with solutions of decreasing pH values (8.50, 7.00, 5.50, and 4.00), imitating the reactions of the alkaline ash particles with the possible alkaline, neutral, and acidic (e.g., acid rain) waters. The most recently deposited ash represents the greatest environmental threat, while 'aged' ash, because of permanent leaching on the dump, was shown to have already lost this pollution potential. On the basis of the determined leachability, it was possible to perform an estimation of the acidity of the regional rainfalls in the last decades.

  9. R dump converter without DC link capacitor for an 8/6 SRM: experimental investigation.

    Science.gov (United States)

    Kavitha, Pasumalaithevan; Umamaheswari, Bhaskaran

    2015-01-01

    The objective of this paper is to investigate the performance of 8/6 switched reluctance motor (SRM) when excited with sinusoidal voltage. The conventional R dump converter provides DC excitation with the help of capacitor. In this paper the converter used is the modified R dump converter without DC link capacitor providing AC or sinusoidal excitation. Torque ripple and speed ripple are investigated based on hysteresis current control. Constant and sinusoidal current references are considered for comparison in both DC and AC excitation. Extensive theoretical and experimental investigations are made to bring out the merits and demerits of AC versus DC excitation. It is shown that the constructionally simple SRM can be favorably controlled with simple R dump converter with direct AC excitation without need for DC link capacitor. A 4-phase 8/6 0.5 kW SRM is used for experimentation.

  10. Properties and interactions of neutrino (1977-1980) beam dump experiments

    International Nuclear Information System (INIS)

    Tsukerman, I.S.

    1981-01-01

    Data on search of instantaneous muon and electron neutrinos in experiments of beam dump type are presented in the review. Neutrino is formed in decays of particles rusulted from pN interactions. First experiments of the dump beam type have been realized at the CERN/SPS accelerator in 1975 and Serpukhov accelerator by the ITEF-IFVE group in 1977 with proton energies of 26 and 70 GeV, respectively. The results of beam dump experiments of the second generation in 1979 in CERN are considered in detail. These experiments have been intended for measuring the effect of instantaneous neutrino. The conclusion is drawn on the presence of instantaneous muon neutrinos in the above experiments [ru

  11. Furfurol-based polymers for the sealing of reactor vessels dumped in the Arctic Kara Sea

    International Nuclear Information System (INIS)

    Heiser, J.H.; Cowgill, M.G.; Alexandrov, V.P.; Dyer, R.S.

    1997-01-01

    Between 1965 and 1988, 16 naval reactor vessels were dumped in the Arctic Kara Sea. Six of the vessels contained spent nuclear fuel that had been damaged during accidents. In addition, a container holding ∼ 60% of the damaged fuel from the No. 2 reactor of the atomic icebreaker 'Lenin' was dumped in 1967. Before dumping, the vessels were filled with a solidification agent, Conservant F, in order to prevent direct contact between the seawater and the fuel and other activated components, thereby reducing the potential for release of radionuclides into the environment. The key ingredient in Conservant F is furfurol (furfuraldehyde). Other constituents vary, depending on specific property requirements, but include epoxy resin, mineral fillers, and hardening agents. The properties of Conservant F in both its cured and uncured states are discussed, and the potential performance of the waste packages containing spent nuclear fuel in the Arctic Kara Sea is evaluated. (author)

  12. Dependability analysis of a safety critical system the LHC beam dumping system at CERN

    CERN Document Server

    Filippini, R

    2006-01-01

    This thesis presents the dependability study of the Beam Dumping System of the Large Hadron Collider (LHC), the high energy particle accelerator to be commissioned at CERN in summer 2007. There are two identical, independent LHC Beam Dumping Systems (LBDS), one per LHC beam, each consisting of a series of magnets that extract the particle beam from the LHC ring into the extraction line leading to the absorbing block. The consequences of a failure within the LBDS can be very severe. This risk is reduced by applying redundancy to the design of the most critical components and on-line surveillance that, in case of a detected failure, issues a safe operation abort, called false beam dump. The system has been studied applying Failure Modes Effects and Criticality Analysis (FMECA) and reliability prediction. The system failure processes have been represented with a state transition diagram, governed by a Markov regenerative stochastic process, and analysed for different operational scenarios for one year of operati...

  13. A magnetized Einzel lens electron dump for the Linac4 H− ion source

    CERN Document Server

    Midttun, O; Kronberger, M; Lettry, J; Pereira, H; Scrivens, R

    2013-01-01

    Linac4 is a 160 MeV linear accelerator which will inject negative hydrogen ions (H−) into CERN’s Proton Synchrotron Booster, a required upgrade to improve the beam brightness in the LHC injector chain. A volume production RF ion source, based on the design of the DESY RF source was implemented, but showed considerable electron dump ablation during operation at 45 keV beam energy. To reduce the electron beam power density in the dump, a magnetized Einzel lens is designed that reduces the beam energy to 10 keV before permanentmagnets dump the electrons on a tungsten surface. Presented in this paper are simulations of the design using IBSimu, the tunable range of parameters depending on the extracted H− and electron current, as well as details of the implementation, the choice of pulsed power converters and the electrode alignment system. In addition, simulations of proton extraction from this source will be shown.

  14. ANALYSIS OF REMEDIATION PROCESS OF THE GROUDWATER COTAMINATION IN AN ILLEGAL DUMPING SITE

    Science.gov (United States)

    Nishida, Norikazu; Furuichi, Toru; Ishii, Kazuei

    Among on-site remediation technologies applied to illegal dumping sites, a technology to remedy contaminated groundwater without removal of the dumped waste is expected to provide a great opportunity to fulfill a societal need due to its economic advantage compared to removal of all waste. However heterogeneously-distributed waste makes the remedial process difficult. In this study, an in situflushing technology was applied to an illegal dumping site in Kuwana city, Mie, in order to remedy groundwater contaminated with several volatile organic compounds (VOCs) within five years. The key to successfully achieve the target was to conduct a series of advanced remediation processes; introducing a new indicator by which multiple VOCs can be estimated integratelly, monitoring the progress of remediation with a contour map of VOC concentration as well as the weighted averages of the concentration derived from the indicator, pinpointing residual contaminants area, reexamining the plan, and taking additional steps that promote further remediation.

  15. Making ultracold molecules in a two-color pump-dump photoassociation scheme using chirped pulses

    International Nuclear Information System (INIS)

    Koch, Christiane P.; Luc-Koenig, Eliane; Masnou-Seeuws, Francoise

    2006-01-01

    This theoretical paper investigates the formation of ground state molecules from ultracold cesium atoms in a two-color scheme. Following previous work on photoassociation with chirped picosecond pulses [Luc-Koenig et al., Phys. Rev. A, 70, 033414 (2004)], we investigate stabilization by a second (dump) pulse. By appropriately choosing the dump pulse parameters and time delay with respect to the photoassociation pulse, we show that a large number of deeply bound molecules are created in the ground triplet state. We discuss (i) broad-bandwidth dump pulses which maximize the probability to form molecules while creating a broad vibrational distribution as well as (ii) narrow-bandwidth pulses populating a single vibrational ground state level, bound by 113 cm -1 . The use of chirped pulses makes the two-color scheme robust, simple, and efficient

  16. A heat source probe for measuring thermal conductivity in waste rock dumps

    International Nuclear Information System (INIS)

    Blackford, M.G.; Harries, J.R.

    1985-10-01

    The development and use of a heat source probe to measure the thermal conductivity of the material in a waste rock dump is described. The probe releases heat at a constant rate into the surrounding material and the resulting temperature rise is inversely related to the thermal conductivity. The probe was designed for use in holes in the dump which are lined with 50 mm i.d. polyethylene liners. The poor thermal contact between the probe and the liner and the unknown conductivity of the backfill material around the liner necessitated long heating and cooling times (>10 hours) to ensure that the thermal conductivity of the dump material was being measured. Temperature data acquired in the field were analysed by comparing them with temperatures calculated using a two-dimensional cylindrical model of the probe and surrounding material, and the heat transfer code HEATRAN

  17. Furfurol-based polymers for the sealing of reactor vessels dumped in the Arctic Kara Sea

    Energy Technology Data Exchange (ETDEWEB)

    Heiser, J.H.; Cowgill, M.G. [Brookhaven National Lab., Upton, NY (United States). Environmental and Waste Technology Center; Sivintsev, Yu.V. [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation); Alexandrov, V.P. [Research and Design Inst. for Power Engineering (Russian Federation); Dyer, R.S. [U.S. Environmental Protection Agency, Washington, DC (United States)

    1997-12-31

    Between 1965 and 1988, 16 naval reactor vessels were dumped in the Arctic Kara Sea. Six of the vessels contained spent nuclear fuel that had been damaged during accidents. In addition, a container holding {approx} 60% of the damaged fuel from the No. 2 reactor of the atomic icebreaker `Lenin` was dumped in 1967. Before dumping, the vessels were filled with a solidification agent, Conservant F, in order to prevent direct contact between the seawater and the fuel and other activated components, thereby reducing the potential for release of radionuclides into the environment. The key ingredient in Conservant F is furfurol (furfuraldehyde). Other constituents vary, depending on specific property requirements, but include epoxy resin, mineral fillers, and hardening agents. The properties of Conservant F in both its cured and uncured states are discussed, and the potential performance of the waste packages containing spent nuclear fuel in the Arctic Kara Sea is evaluated. (author) 4 refs.

  18. Pollution extents of organic substances from a coal gangue dump of Jiulong Coal Mine, China

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Y.Z.; Fan, J.S.; Qin, P.; Niu, H.Y. [Hebei University of Engineering, Handan (China)

    2009-02-15

    This paper addresses the distribution and occurrence of harmful organic substances in coal gangue dump from Jiulong Coal Mine and its influence on the environment. The samples were taken from the coal gangue dump and coal waste water stream and analyzed by organic geochemical methods. The results indicate that the coal gangues contain abundant harmful organic substances like polycyclic aromatic hydrocarbons. The TOC and sulfur contents of the samples are much higher than those of the background sample except Sample JL7. The contents of organic bulk parameters are relatively high. Ten carcinogenic PAHs were identified and these harmful organic substances have influenced the surrounding area. Along the waste water stream, organic substances pollute at least 1,800 m far from the coal gangue dump.

  19. Design of the 70 mm twin aperture superconducting quadrupole for the LHC dump insertion

    CERN Document Server

    Kirby, G A; Taylor, T M; Trinquart, G

    1996-01-01

    The LHC dump insertion features a pair of superconducting quadrupoles located on either side of a 340 m long straight section. Two horizontally deflecting kickers, located in between the quadrupole pairs, and a septum in the centre of the insertion, vertically deflect the two counter-rotating beams past the quadrupoles on the downstream sides, and into the dump areas. Due to the layout, the optical ß function in the quadrupoles is around 640 m, the largest around the LHC at injection. The quadrupoles must therefore have enlarged aperture and specially designed cryostats to allow for the safe passage of both the circulating and ejected beams. In this paper we present the design of the twin aperture dump quadrupole based on the 70 mm four layer coil proposed for the LHC low-ß quadrupoles. In preparation for model construction, we report on improvements of the coil design and a study of the retaining structures.

  20. The network of dump design. A report on experience; Das Netzwerk der Haldenkunst. Ein Erfahrungsbericht

    Energy Technology Data Exchange (ETDEWEB)

    Hermanns, Josef [Buero Hermanns Architekten - Ingenieure - Landschaftsarchitekten, Hattingen (Germany)

    2009-10-22

    On the basis of long experience in the planning of the most diverse mining projects consideration was already given at the end of the last century in the Hermanns architects' office to the planning of dirt heaps from specific points of view differently from the conventional way. The office was concerned in particular with the potential for subsequent use of dumps under the premises specified by the mining companies. Hence the idea of considering dumps from architectural and artistic points of view arose at the end of 2006, because in association with the region chosen in 2006 to be European city of culture in 2010 - Essen for the Ruhr district - an opportunity arose to place the subject of dumps in an artistic and cultural context with the result that the hypothesis of implementation of new ideas in a regional context would be more easily formulated. (orig.)

  1. Partial Cavity Flows at High Reynolds Numbers

    Science.gov (United States)

    Makiharju, Simo; Elbing, Brian; Wiggins, Andrew; Dowling, David; Perlin, Marc; Ceccio, Steven

    2009-11-01

    Partial cavity flows created for friction drag reduction were examined on a large-scale. Partial cavities were investigated at Reynolds numbers up to 120 million, and stable cavities with frictional drag reduction of more than 95% were attained at optimal conditions. The model used was a 3 m wide and 12 m long flat plate with a plenum on the bottom. To create the partial cavity, air was injected at the base of an 18 cm backwards-facing step 2.1 m from the leading edge. The geometry at the cavity closure was varied for different flow speeds to optimize the closure of the cavity. Cavity gas flux, thickness, frictional loads, and cavity pressures were measured over a range of flow speeds and air injection fluxes. High-speed video was used extensively to investigate the unsteady three dimensional cavity closure, the overall cavity shape and oscillations.

  2. Microbial community structure of leaf-cutter ant fungus gardens and refuse dumps.

    Science.gov (United States)

    Scott, Jarrod J; Budsberg, Kevin J; Suen, Garret; Wixon, Devin L; Balser, Teri C; Currie, Cameron R

    2010-03-29

    Leaf-cutter ants use fresh plant material to grow a mutualistic fungus that serves as the ants' primary food source. Within fungus gardens, various plant compounds are metabolized and transformed into nutrients suitable for ant consumption. This symbiotic association produces a large amount of refuse consisting primarily of partly degraded plant material. A leaf-cutter ant colony is thus divided into two spatially and chemically distinct environments that together represent a plant biomass degradation gradient. Little is known about the microbial community structure in gardens and dumps or variation between lab and field colonies. Using microbial membrane lipid analysis and a variety of community metrics, we assessed and compared the microbiota of fungus gardens and refuse dumps from both laboratory-maintained and field-collected colonies. We found that gardens contained a diverse and consistent community of microbes, dominated by Gram-negative bacteria, particularly gamma-Proteobacteria and Bacteroidetes. These findings were consistent across lab and field gardens, as well as host ant taxa. In contrast, dumps were enriched for Gram-positive and anaerobic bacteria. Broad-scale clustering analyses revealed that community relatedness between samples reflected system component (gardens/dumps) rather than colony source (lab/field). At finer scales samples clustered according to colony source. Here we report the first comparative analysis of the microbiota from leaf-cutter ant colonies. Our work reveals the presence of two distinct communities: one in the fungus garden and the other in the refuse dump. Though we find some effect of colony source on community structure, our data indicate the presence of consistently associated microbes within gardens and dumps. Substrate composition and system component appear to be the most important factor in structuring the microbial communities. These results thus suggest that resident communities are shaped by the plant degradation

  3. Radioactive-waste ocean dumping will have negligible enviromental impact. Conclusion of draft assessment of NSB

    Energy Technology Data Exchange (ETDEWEB)

    1976-11-01

    This draft report is the result of extensive studies based on the best available information in the field of oceanography, marine radiobiology and health physics. On various basic considerations, assessment was undertaken, and the following conclusion was reached. The quantity of radioactivity to be dumped at one time is assumed to be 500 Ci in the case of test dumping, and 10/sup 5/ Ci/year in the case of full-scale dumping. The conditions required for the dumping sea area are that the bottom water flow and upwelling amount are limited, and that the sea bottom is flat. The horizontal dispersion coefficient of 10/sup 7/ cm/sup 2//sec and the vertical dispersion coefficient of 2 x 10/sup 2/ cm/sup 2//sec are assumed. It is assumed that the radionuclides in the disposed package would leached out as soon as it reaches the sea bottom, and would not show any physicochemical behavior. Typycal radionuclides are classified into 5 groups in terms of their half lives, and their estimated concentrations at 1 km depth are tabulated. The maximum level of individual dose and the magnitude of population dose were assessed on the fishermen working in the dumping sea area, and the adults, children and infants who were expected to receive higher dose on account of the larger intake of fish products than average. The dose level given with the dose assessment model and various panamentors under the dumping conditions is much lower than natural radiation and the permissible level recommended by ICRP.

  4. Specifics of stands formation at coalmine dumps in forest-steppe zone

    Directory of Open Access Journals (Sweden)

    R. T. Murzakmаtov

    2018-02-01

    Full Text Available Rock dumps of coalmines have high potential for forest regeneration and environmental capacity, which are dependent on the technology of reclamation and the properties of technogenic soils and grounds. Traditional forestry methods for obtaining the main criteria of biological indicators of woody vegetation were used in the study as follows: ground seed germination, seedling planting technology, composition and increment of tree stands, root structure, care harvesting of undergrowth, biotopic classification. Natural overgrowing of dumps is dependent on the availability of seeds and conditions for their germination and subsequent growth. Most of the zonal tree and shrub species are able to colonize and grow on the coalmine dumps. Mineralization of the dumps surfaces without rich soil stratum, porosity of the upper horizon of lithostratum, and low nutrient content (nitrogen give benefits in the growth and subsequent formation of birch, pine and sea-buckthorn stands. Afforestation is the cheapest and most effective method of biological reclamation. The analysis of artificial reforestation shows the probability of targeted plantation cultivation of various tree species. The use of a wide range of tree and shrub species make it possible to create biologically diverse intrazonal technogenic ecosystems with high recreational and economic productivity. Wildfires spreading out in spring season on herbaceous rags limit the overgrowth of the dumps by forest vegetation. Two-year cyclical increment decline of trees due to provocative spring warming takes place. The zoogenic factor, especially zoo chores distribution of berry plants, has essential value for forest forming process. By the results of forest formation analysis at rock dumps, alveolate-hilly technology of mine reclamation was developed, which allows to significantly improve dumps’ afforestation capacity, their biological posttechnogenic diversity and productivity.

  5. Normal Conducting RF Cavity for MICE

    International Nuclear Information System (INIS)

    Li, D.; DeMello, A.; Virostek, S.; Zisman, M.; Summers, D.

    2010-01-01

    Normal conducting RF cavities must be used for the cooling section of the international Muon Ionization Cooling Experiment (MICE), currently under construction at Rutherford Appleton Laboratory (RAL) in the UK. Eight 201-MHz cavities are needed for the MICE cooling section; fabrication of the first five cavities is complete. We report the cavity fabrication status including cavity design, fabrication techniques and preliminary low power RF measurements.

  6. Thermal conditions within tree cavities in ponderosa pine (Pinus ponderosa) forests: potential implications for cavity users

    Science.gov (United States)

    Vierling, Kerri T.; Lorenz, Teresa J.; Cunningham, Patrick; Potterf, Kelsi

    2017-11-01

    Tree cavities provide critical roosting and breeding sites for multiple species, and thermal environments in these cavities are important to understand. Our objectives were to (1) describe thermal characteristics in cavities between June 3 and August 9, 2014, and (2) investigate the environmental factors that influence cavity temperatures. We placed iButtons in 84 different cavities in ponderosa pine (Pinus ponderosa) forests in central Washington, and took hourly measurements for at least 8 days in each cavity. Temperatures above 40 °C are generally lethal to developing avian embryos, and 18% of the cavities had internal temperatures of ≥ 40 °C for at least 1 h of each day. We modeled daily maximum cavity temperature, the amplitude of daily cavity temperatures, and the difference between the mean internal cavity and mean ambient temperatures as a function of several environmental variables. These variables included canopy cover, tree diameter at cavity height, cavity volume, entrance area, the hardness of the cavity body, the hardness of the cavity sill (which is the wood below the cavity entrance which forms the barrier between the cavity and the external environment), and sill width. Ambient temperature had the largest effect size for maximum cavity temperature and amplitude. Larger trees with harder sills may provide more thermally stable cavity environments, and decayed sills were positively associated with maximum cavity temperatures. Summer temperatures are projected to increase in this region, and additional research is needed to determine how the thermal environments of cavities will influence species occupancy, breeding, and survival.

  7. Red-cockaded woodpecker nest-cavity selection: relationships with cavity age and resin production

    Science.gov (United States)

    Richard N. Conner; Daniel Saenz; D. Craig Rudolph; William G. Ross; David L. Kulhavy

    1998-01-01

    The authors evaluated selection of nest sites by male red-cockaded woodpeckers (Picoides borealis) in Texas relative to the age of the cavity when only cavities excavated by the woodpeckers were available and when both naturally excavated cavities and artificial cavities were available. They also evaluated nest-cavity selection relative to the ability of naturally...

  8. Pseudo-harmonics method: an application to thermal reactors

    International Nuclear Information System (INIS)

    Silva, F.C. da; Rotenberg, S.; Thome Filho, Z.D.

    1985-10-01

    Several applications of the Pseudo-Harmonics method are presented, aiming to calculate the neutron flux and the perturbed eigenvalue of a nuclear reactor, like PWR, with three enrichment regions as Angra-1 reactor. In the reference reactor, perturbations of several types as global as local were simulated. The results were compared with those from the direct calculation. (E.G.) [pt

  9. To avoid operating on pseudo tumoral pulmonary infarctions ...

    African Journals Online (AJOL)

    Pulmonary infarction usually appears as a hump-shaped triangular opacity with its base applied to a pleural surface. In some cases, pulmonary infarctions may appear as a pseudo tumoral opacity mimicking lung cancer. Thoracotomy could be prevented by repeating CT scan in properly selected patients. Pan African ...

  10. Pseudo potentials and model potentials in atomic collisions

    International Nuclear Information System (INIS)

    Reyes, O.; Jouin, H.; Fuentealba, P.

    1988-01-01

    In this work, it is discussed the main differences between the use of pseudo-potentials and model potentials in collision problems . It is shown the potential energy curves for distinct systems obtained with both kinds of potentials. (A.C.A.S.) [pt

  11. IMRT optimization with pseudo-biologic objective function

    International Nuclear Information System (INIS)

    Yi, B. Y.; Ahn, S. D.; Kim, J. H.; Lee, S. W.; Choi, E. K.

    2002-01-01

    The pseudo-biologic objective function has been proposed for the IMRT optimization. It is similar to the biological objective function in mathematical shape, but uses physical parameters. The pseudo-biologic objective function concept is consisted of the target coverage index (TCI) and the organ score index (OSI), was introduced. The TCI was expressed as the sum of all of the weighted bins of target dose volume histogram (DVH). The weights were given as the normal distribution of which the average is 100 % and the standard deviation is ±. The OSI was expressed as similar way. The average of the normal distribution was 0% of the dose and that of standard deviation was selected as a function of limiting dose and its importance. The objective function could be calculated as the product of the TCI and OSI's. The RTP Tool Box (RTB) was used for this study. The constraints applied in the optimization was intuitively clinical experience based numbers, while the physical objective function asks just numbers which are not necessarily based on the clinic, and the parameters for the biologic objective functions are uncertain. The OSI's from the pseudo-biological function showed better results than from the physical functions, while TCI's showed similar tendency. We could show that the pseudo-biologic function can be used for an IMRT objective function on behalf of the biological objective function

  12. Empirical pseudo-potential studies on electronic structure

    Indian Academy of Sciences (India)

    Theoretical investigations of electronic structure of quantum dots is of current interest in nanophase materials. Empirical theories such as effective mass approximation, tight binding methods and empirical pseudo-potential method are capable of explaining the experimentally observed optical properties. We employ the ...

  13. Cryptography, statistics and pseudo-randomness (Part 1)

    NARCIS (Netherlands)

    Brands, S.; Gill, R.D.

    1995-01-01

    In the classical approach to pseudo-random number generators, a generator is considered to perform well if its output sequences pass a battery of statistical tests that has become standard. In recent years, it has turned out that this approach is not satisfactory. Many generators have turned out to

  14. Stepanov-like weighted pseudo almost automorphic solutions to ...

    Indian Academy of Sciences (India)

    Abstract. In this article, we study the concept of Stepanov-like weighted pseudo almost automorphic solutions to fractional order abstract integro-differential equations. We establish the results with Lipschitz condition and without Lipschitz condition on the forcing term. An interesting example is presented to illustrate the main ...

  15. Allelopathic potential of Robinia pseudo-acacia L.

    Science.gov (United States)

    Nasir, Habib; Iqbal, Zahida; Hiradate, Syuntaro; Fujii, Yoshiharu

    2005-09-01

    Robinia pseudo-acacia L. (black locust) is a nonindigenous species currently invading the central part of Japanese grasslands. Several allelochemicals were identified and characterized from the leaf tissue. The growth of both radicle and hypocotyl in the tested species (barnyard grass, white clover, lettuce, and Chinese cabbage) was reduced when grown in soil mixed with the leaves of R. pseudo-acacia at various concentrations. Aqueous leaf extracts, when bioassayed, exhibited a significant suppression of radicle growth. Chromatographic separation of an ethanolic extract of R. pseudo-acacia leaves resulted in isolation of three compounds, identified as robinetin (1), myricetin (2), and quercetin (3) by nuclear magnetic resonance and mass spectroscopy. All inhibited root and shoot growth of lettuce. Robinetin, found in a large amount, caused 50% suppression of the root and shoot growth of lettuce at 100 ppm. The presence of these bioactive substances in leaf tissue suggests a potential role for flavonoids in R. pseudo-acacia invasion in introduced habitats.

  16. Evolutionary Pseudo-Relaxation Learning Algorithm for Bidirectional Associative Memory

    Institute of Scientific and Technical Information of China (English)

    Sheng-Zhi Du; Zeng-Qiang Chen; Zhu-Zhi Yuan

    2005-01-01

    This paper analyzes the sensitivity to noise in BAM (Bidirectional Associative Memory), and then proves the noise immunity of BAM relates not only to the minimum absolute value of net inputs (MAV) but also to the variance of weights associated with synapse connections. In fact, it is a positive monotonically increasing function of the quotient of MAV divided by the variance of weights. Besides, the performance of pseudo-relaxation method depends on learning parameters (λ and ζ), but the relation of them is not linear. So it is hard to find a best combination of λ and ζ which leads to the best BAM performance. And it is obvious that pseudo-relaxation is a kind of local optimization method, so it cannot guarantee to get the global optimal solution. In this paper, a novel learning algorithm EPRBAM (evolutionary psendo-relaxation learning algorithm for bidirectional association memory) employing genetic algorithm and pseudo-relaxation method is proposed to get feasible solution of BAM weight matrix. This algorithm uses the quotient as the fitness of each individual and employs pseudo-relaxation method to adjust individual solution when it does not satisfy constraining condition any more after genetic operation. Experimental results show this algorithm improves noise immunity of BAM greatly. At the same time, EPRBAM does not depend on learning parameters and can get global optimal solution.

  17. Polynomial constitutive model for shape memory and pseudo elasticity

    International Nuclear Information System (INIS)

    Savi, M.A.; Kouzak, Z.

    1995-01-01

    This paper reports an one-dimensional phenomenological constitutive model for shape memory and pseudo elasticity using a polynomial expression for the free energy which is based on the classical Devonshire theory. This study identifies the main characteristics of the classical theory and introduces a simple modification to obtain better results. (author). 9 refs., 6 figs

  18. The characteristics of failure among students who experienced pseudo thinking

    Science.gov (United States)

    Anggraini, D.; Kusmayadi, T. A.; Pramudya, I.

    2018-04-01

    The purpose of this research is to describe the thinking process of students who experienced pseudo thinking when solving the straight line equation. The result of this study shows the characteristics of error that caused students to experience pseudo thinking when solving the problem and their relation with students’ metacognition skill. This qualitative research was conducted in State 16 Junior High School in Surakarta, Indonesia during the odd semester of 2017/2018 academic year. The subjects of the study were students Junior High School students of 8th grade chosen using purposive sampling technique. Data were collected through the administration of think aloud method. The result showed that the characteristics of errors among the subjects are: 1) the answers resulted from pseudo thinking when solving the problem were obtained from the spontaneous, fast, unconscious and uncontrolled thinking process; 2) students had misconception; 3) students had tendency to memorize the formula and imitate the completion procedure; 4) students experienced fuzzy memory when solving the problem. From the mistakes among students who experienced pseudo thinking, their metacognition ability could be inferred.

  19. Material machining with pseudo-spark electron beams

    International Nuclear Information System (INIS)

    Benker, W.; Christiansen, J.; Frank, K.; Gundel, H.; Redel, T.; Stetter, M.

    1989-01-01

    The authors give a brief description of the production of pseudo-spark (low pressure gas discharge) electron beams. They illustrate the use of these electron beams for machining not only conducting, semiconducting and insulating materials, but also thin layers of such materials as high temperature superconducting ceramics

  20. Random matrix theory for pseudo-Hermitian systems: Cyclic blocks

    Indian Academy of Sciences (India)

    We discuss the relevance of random matrix theory for pseudo-Hermitian systems, and, for Hamiltonians that break parity and time-reversal invariance . In an attempt to understand the random Ising model, we present the treatment of cyclic asymmetric matrices with blocks and show that the nearest-neighbour spacing ...