WorldWideScience

Sample records for prototype regional mineral

  1. Manufacture of mineral-insulated conductor for ITER prototype ELM and VS coil

    Energy Technology Data Exchange (ETDEWEB)

    Long, Feng, E-mail: longf@ipp.ac.cn [Institute of Plasma Physics of Chinese Academy of Sciences, Hefei 230031 (China); Wu, Yu; Jin, Huan; Yu, Min; Han, Qiyang; Ling, Feng [Institute of Plasma Physics of Chinese Academy of Sciences, Hefei 230031 (China); Kalish, Michael [Princeton Plasma Physics Laboratory, PO Box 451, Princeton, NJ 08543 (United States)

    2015-06-15

    Highlights: • Compaction method is successfully developed for MIC manufacture. • Manufactured MICs show well controlled outer diameter and good electrical properties. • Insulation resistance of all the MICs is higher than 100 GΩ@DC 2500 V. - Abstract: An ITER Organization (IO) Task Agreement (TA) “Final Design and Prototyping of the ITER In-Vessel Coils (IVC) and Feeders” is almost finished by Institute of Plasma Physics, Chinese Academy of Sciences (ASIPP). ITER IVCs consist of edge-localized mode (ELM) and vertical stabilization (VS) coils. One prototype Mid-ELM coil complete with 19 brackets brazed with the conductors and one prototype 120° section of upper VS coil with structural components brazed to the conductors have been fabricated. Compaction method is developed successfully for the mineral-insulated conductor (MIC) manufacture. Approximate 110 m Inconel 625 jacket MICs for Mid-ELM prototype coil and 80 m stainless steel 316L jacket MICs for VS prototype coil were manufactured. Most of the copper tubes used for the MICs fabrication failed the ultrasonic testing (UT), but the jacket tubes have good passing rate. Manufacture processes and inspection for the MICs are presented in this paper.

  2. Manufacture of mineral-insulated conductor for ITER prototype ELM and VS coil

    International Nuclear Information System (INIS)

    Long, Feng; Wu, Yu; Jin, Huan; Yu, Min; Han, Qiyang; Ling, Feng; Kalish, Michael

    2015-01-01

    Highlights: • Compaction method is successfully developed for MIC manufacture. • Manufactured MICs show well controlled outer diameter and good electrical properties. • Insulation resistance of all the MICs is higher than 100 GΩ@DC 2500 V. - Abstract: An ITER Organization (IO) Task Agreement (TA) “Final Design and Prototyping of the ITER In-Vessel Coils (IVC) and Feeders” is almost finished by Institute of Plasma Physics, Chinese Academy of Sciences (ASIPP). ITER IVCs consist of edge-localized mode (ELM) and vertical stabilization (VS) coils. One prototype Mid-ELM coil complete with 19 brackets brazed with the conductors and one prototype 120° section of upper VS coil with structural components brazed to the conductors have been fabricated. Compaction method is developed successfully for the mineral-insulated conductor (MIC) manufacture. Approximate 110 m Inconel 625 jacket MICs for Mid-ELM prototype coil and 80 m stainless steel 316L jacket MICs for VS prototype coil were manufactured. Most of the copper tubes used for the MICs fabrication failed the ultrasonic testing (UT), but the jacket tubes have good passing rate. Manufacture processes and inspection for the MICs are presented in this paper

  3. Finding Trapped Miners by Using a Prototype Seismic Recording System Made from Music-Recording Hardware

    Science.gov (United States)

    Pratt, Thomas L.

    2009-01-01

    The goal of this project was to use off-the-shelf music recording equipment to build and test a prototype seismic system to listen for people trapped in underground chambers (mines, caves, collapsed buildings). Previous workers found that an array of geophones is effective in locating trapped miners; displaying the data graphically, as well as playing it back into an audio device (headphones) at high speeds, was found to be effective for locating underground tapping. The desired system should record the data digitally to allow for further analysis, be capable of displaying the data graphically, allow for rudimentary analysis (bandpass filter, deconvolution), and allow the user to listen to the data at varying speeds. Although existing seismic reflection systems are adequate to record, display and analyze the data, they are relatively expensive and difficult to use and do not have an audio playback option. This makes it difficult for individual mines to have a system waiting on the shelf for an emergency. In contrast, music recording systems, like the one I used to construct the prototype system, can be purchased for about 20 percent of the cost of a seismic reflection system and are designed to be much easier to use. The prototype system makes use of an ~$3,000, 16-channel music recording system made by Presonus, Inc., of Baton Rouge, Louisiana. Other manufacturers make competitive systems that would serve equally well. Connecting the geophones to the recording system required the only custom part of this system - a connector that takes the output from the geophone cable and breaks it into 16 microphone inputs to be connected to the music recording system. The connector took about 1 day of technician time to build, using about $300 in off-the-shelf parts. Comparisons of the music recording system and a standard seismic reflection system (A 24-channel 'Geode' system manufactured by Geometrics, Inc., of San Jose, California) were carried out at two locations. Initial

  4. Acquisition and manipulation of computed tomography images of the maxillofacial region for biomedical prototyping

    International Nuclear Information System (INIS)

    Meurer, Maria Ines; Silva, Jorge Vicente Lopes da; Santa Barbara, Ailton; Nobre, Luiz Felipe; Oliveira, Marilia Gerhardt de; Silva, Daniela Nascimento

    2008-01-01

    Biomedical prototyping has resulted from a merger of rapid prototyping and imaging diagnosis technologies. However, this process is complex, considering the necessity of interaction between biomedical sciences and engineering. Good results are highly dependent on the acquisition of computed tomography images and their subsequent manipulation by means of specific software. The present study describes the experience of a multidisciplinary group of researchers in the acquisition and manipulation of computed tomography images of the maxillofacial region aiming at biomedical prototyping for surgical purposes. (author)

  5. Sustainable development of the minerals sector in the APEC region

    Energy Technology Data Exchange (ETDEWEB)

    Jane Melanie; Kate Penney; Angelica Austin; Chris Rumley; Robert Curtotti

    2007-01-15

    The objectives in this report are to analyse the global market outlook for minerals over the medium term, identify key issues affecting the sustainability of the minerals sector in the APEC region and recommend possible actions to respond to these issues. These issues are structured around the APEC pillars of trade and investment liberalisation; business facilitation; and economic and technical cooperation. The report highlights the need for a strong and effective policy framework to allow APEC economies to capitalise on growth opportunities in global minerals markets. This is an updated version of ABARE Research Report 06.8. Minerals covered are: thermal coal. metallurgical coal, aluminium, alumina, bauxite, copper, gold, iron ores, lead, nickel, tin, uranium and zinc. 15 figs., 19 tabs.

  6. Sustainable mineral resources management: from regional mineral resources exploration to spatial contamination risk assessment of mining

    Science.gov (United States)

    Jordan, Gyozo

    2009-07-01

    Wide-spread environmental contamination associated with historic mining in Europe has triggered social responses to improve related environmental legislation, the environmental assessment and management methods for the mining industry. Mining has some unique features such as natural background contamination associated with mineral deposits, industrial activities and contamination in the three-dimensional subsurface space, problem of long-term remediation after mine closure, problem of secondary contaminated areas around mine sites, land use conflicts and abandoned mines. These problems require special tools to address the complexity of the environmental problems of mining-related contamination. The objective of this paper is to show how regional mineral resources mapping has developed into the spatial contamination risk assessment of mining and how geological knowledge can be transferred to environmental assessment of mines. The paper provides a state-of-the-art review of the spatial mine inventory, hazard, impact and risk assessment and ranking methods developed by national and international efforts in Europe. It is concluded that geological knowledge on mineral resources exploration is essential and should be used for the environmental contamination assessment of mines. Also, sufficient methodological experience, knowledge and documented results are available, but harmonisation of these methods is still required for the efficient spatial environmental assessment of mine contamination.

  7. Uranium mineralization in the central region of Cuba

    International Nuclear Information System (INIS)

    Valdez, M.G.; Olivera, J.; Fernandez, P.

    1995-01-01

    The present work shows different geological and geophysical index for uranium mineralization found at Loma Alta iron ore deposit, located in the central region of Cuba. In this deposit was carried out pull work of iron ore. The tunnels were radiometrically documented in the wall and the floor observing some anomalies of the gamma ray intensity (up to 1700 c.p.s.) associated with the poor iron ore. In those points were collected solid sample. The obtained results were very important (uranium concentrations values up to 3500 ppm)

  8. Total body and regional bone mineral content in hemodialysis patients

    International Nuclear Information System (INIS)

    Hagiwara, Satoshi; Aratani, Hideyui; Miki, Takami; Nishizawa, Yoshiki; Okamura, Terue; Koizumi, Yoshiko; Ochi, Hironobu; Morii, Hirotoshi

    1994-01-01

    Bone mineral content (BMC) in the total body and lumbar spine was evaluated in 126 hemodialysis patients (60 males, 66 females) by dual photon absorptiometry with the Norland DBD 2600. Measurements of: 1) total body BMC divided by lean body mass (BMC TB /LBM), 2) bone mineral density (BMD) of total body, 3) BMD of four regional sections (head, trunk, pelvis, and legs), and 4) BMD of lumbar spine, generally showed a significant decrease in the hemodialysis patients compared to the reference population. However, arm BMD did not show a significant difference between patients and control populations. The z-score of BMC TB /LBM declined significantly throughout the duration of hemodialysis, although that of the lumbar spine BMD did not. It should be noted that the degree of decrease in BMC was more prominent in the total body measurement than in the lumbar spine measurement. There was preferential osteopenia of the total body in the hemodialysis patients. Although the lumbar spine BMD showed a lower value than the control population, the lumbar spine is not the recommended region to monitor the BMD change in hemodialysis patients. (author)

  9. Bone mineral density measurement over the shoulder region

    DEFF Research Database (Denmark)

    Doetsch, A M; Faber, J; Lynnerup, N

    2002-01-01

    values decreased with age (P shoulder BMD levels increased significantly with increased body mass index (BMI) (P positive relationship between the increased hip/shoulder BMD differential with BMI supports the conclusion that the shoulder is subject......The purpose of this study was to (1). establish a method for measuring bone mineral density (BMD) over the shoulder region; (2). compare the relationship between shoulder BMD levels with hip BMD and body mass index (BMI); and (3). discuss the relevance of the shoulder scan as an early indicator...... of osteoporosis compared with hip scans, the latter representing a weight-bearing part of the skeleton. We developed a scanning procedure, including a shoulder fixation device, and determined the most appropriate software in order to establish a reference material with the highest possible precision. Duplicate...

  10. Mineral Resource Points, US EPA Region 9, 2006, USGS

    Data.gov (United States)

    U.S. Environmental Protection Agency — Mineral resource occurrence data covering the world, most thoroughly within the U.S. This database contains the records previously provided in the Mineral Resource...

  11. Minerals

    Science.gov (United States)

    Minerals are important for your body to stay healthy. Your body uses minerals for many different jobs, including keeping your bones, muscles, heart, and brain working properly. Minerals are also important for making enzymes and hormones. ...

  12. The New Nordic Diet as a prototype for regional sustainable diets

    DEFF Research Database (Denmark)

    Bügel, Susanne Gjedsted; Hertwig, Jostein; Kahl, Johannes

    2016-01-01

    A main challenge in sustainable food systems is to link sustainable production to sustainable diets and consumption patterns. The new Nordic diet (NND) builds on and shares the Mediterranean diet (MD) thinking, but utilizes the ingredients and flavours of a northern climate. In both diets...... both wild and domesticated sources. Both diets have been associated with health benefits. The NND is a prototype regional diet taking health, food culture, palatability and the environment into account. Thus, the principles and guidelines could be applied in any region of the world. There are currently...

  13. Vitamin and Mineral Support in Children from Kharkiv Region

    Directory of Open Access Journals (Sweden)

    T.V. Frolova

    2016-08-01

    Full Text Available The mineral imbalance and hypovitaminosis significantly affect the level of a child’s health. The objective of the study: the analysis of vitamin and mineral supplementation of schoolchildren. 230 children aged 7 to 17 years underwent comprehensive examination with involvement of different specialty experts. Determination of vitamin content in the blood serum was conducted taking into account the analysis of actual nutrition by high performance liquid chromatography on Varian apparatus. The levels of macro- and microelements in the hair of children were evaluated by characteristic X-ray method on X-ray spectrometer X-Lab 2000. Analysis of the findings showed that nutrition of schoolchildren has 30–40 % energy deficit, which is associated with protein deficiency and excessive intake of carbohydrates (over 20 % due to simple sugars. The nutrition of all examined pupils had a significant deficiency of vitamins A, B, E, D, and vitamin C. The study of the content of vitamins in the blood serum showed that all children had a deficiency of at least one of the major vitamins, and 73.8 % of children had multivitamins deficiency. It was found that 78.8 % of children had mineral disturbances and imbalance in the ratio of major essential elements. It is established that 66.7 % of children with hypovitaminosis and mineral imbalance in the past medical history had a long period of recovery after acute diseases, and 23.1 % of children had various complications of these diseases.

  14. Chinese Gold Miners of the Mid-Columbia Region; TOPICAL

    International Nuclear Information System (INIS)

    J. J. Sharpe

    1999-01-01

    This report was compiled to provide historical information to assist cultural resources personnel to identify features and artifacts that might relate to Chinese placer mining along the Hanford Reach of the Columbia River. Historical information indicates that Chinese miners pursued placer gold along the Hanford Reach

  15. Minerals

    Science.gov (United States)

    ... Aren't minerals something you find in the earth, like iron and quartz? Well, yes, but small ... canned salmon and sardines with bones leafy green vegetables, such as broccoli calcium-fortified foods — from orange ...

  16. THE ORGANIZATIONAL-ECONOMIC MECHANISM OF RESTRUCTURING OF THE MARKET OF MINERAL OIL IN REGION

    Directory of Open Access Journals (Sweden)

    V.I. Efimenkov

    2007-12-01

    Full Text Available Restructuring, in opinion of the experts, one of the basic ways of steady development of managing subjects in modern conditions. In clause strategy of organizational-economic restructuring of the regional market of mineral oil is considered. Concrete actions of complex restructuring of the market of mineral oil in region and the mechanism of management are resulted by reorganization of the given market.

  17. Geology and mineral technology of the grants uranium region 1979

    International Nuclear Information System (INIS)

    Rautman, C.A.

    1980-01-01

    Forty six papers which were presented at the 1979 Symposium on the Geology of the Grants Uranium Region plus three more are included in this Proceedings. The papers cover the geology of the Grants region with discussions of exploration history and methods, individual deposits, petrographic investigations, field studies mining and experimental studies. Other topics such as ground water hydrology and severence taxes are also included. All papers have been abstracted and all but four have been indexed

  18. Minerals

    Directory of Open Access Journals (Sweden)

    Vaquero, M. P.

    1998-08-01

    Full Text Available The possible changes in the mineral composition of food during frying could be the consequence of losses by leaching, or changes in concentrations caused by exchanges between the food and culinary fat of other compounds. The net result depends on the type of food, the frying fat used and the frying process. Moreover, the modifications that frying produces in other nutrients could indirectly affect the availability of dietary minerals. The most outstanding ones are those that can take place in the fat or in the protein. With respect to the interactions between frying oils and minerals, we have recent knowledge concerning the effects of consuming vegetable oils used in repeated fryings of potatoes without turnover, on the nutritive utilization of dietary minerals. The experiments have been carried out in pregnant and growing rats, which consumed diets containing, as a sole source of fat, the testing frying oils or unused oils. It seems that the consumption of various frying oils, with a polar compound content lower or close to the maximum limit of 25% accepted for human consumption, does not alter the absorption and metabolism of calcium, phosphorous, iron or copper. Magnesium absorption from diets containing frying oils tends to increase but the urinary excretion of this element increases, resulting imperceptible the variations in the magnesium balance. The urinary excretion of Zn also increased although its balance remained unchanged. Different studies referring to the effects of consuming fried fatty fish on mineral bioavailability will also be presented. On one hand, frying can cause structural changes in fish protein, which are associated with an increase in iron absorption and a decrease in body zinc retention. The nutritive utilization of other elements such as magnesium, calcium and copper seems to be unaffected. On the other hand; it has been described that an excess of fish fatty acids in the diet produces iron depletion, but when fatty

  19. Energy and minerals industries in national, regional, and state economies

    Science.gov (United States)

    D. J. Shields; S. A. Winter; G. S. Alward; K. L. Hartung

    1996-01-01

    This report presents information on the contribution of the extractive industries to the domestic economy at different geopolitical scales. Areas where resource production is important to gross state or regional product, employment, or income are highlighted. Output, employment, value added, and personal and total income multipliers are reported for the energy and...

  20. RETRIEVAL OF MINERAL ABUNDANCES OF THE DELTA REGION IN EBERSWALDE, MARS

    Directory of Open Access Journals (Sweden)

    X. Wu

    2017-07-01

    Full Text Available Eberswalde Crater, a hotspot of Mars exploration, possesses an unambiguous hydrological system. However, little research has been performed on the large-scale mineral abundances retrieval in this region. Hence, we employed hyperspectral unmixing technology to quantitatively retrieve mineral abundances of the delta region in Eberswalde. In this paper, the single-scattering albedos were calculated by the Hapke bidirectional reflectance function from Compact Reconnaissance Imaging Spectrometer for Mars (CRISM data (FRT000060DD and CRISM spectral library respectively, and a sparse unmixing algorithm was adopted to quantitatively retrieve mineral abundances. The abundance maps show that there are six kinds of minerals (pyroxene, olivine, plagioclase, siderite, diaspore, and tremolite. By comparing minerals spectra obtained from images with corresponding spectra in spectral library, we found the similar trend in both curves. Besides, the mineral abundance maps derived in this study agree well spatially with CRISM parameter maps. From the perspective of mineralogy, the instability of pyroxene and olivine indicates the area in which they distribute is close to provenance, and the original provenance is ultrabasic rock (e.g. peridotite and basic rock (e.g. gabbro, respectively. And minerals, existing in the area of alluvial fan, also distribute in the outside of alluvial fan, which might be caused by fluid transportation.

  1. On the genesis and dynamics of mineral waters of Essentuki deposit in the Great Region of Caucasian Mineral Waters on the basis of uranium isotope information

    International Nuclear Information System (INIS)

    Chalov, P.I.; Tikhonov, A.I.; Kiselev, G.P.; Merkulova, K.I.

    1991-01-01

    The sources of the Great Region of Caucasian Mineral Waters are established and contribution of each source in the formation of this region is determined using the data on isotopic ratio and content of uranium in mineral waters. The investigation relies on the fact that 234 U/ 238 U radioactivity ratio used as a tracer in different for waters which drain the rocks with different content and distribution of uranium therein. The investigation results reveal the peculiarities of the geological history of the above region and can be used for predicting new deposits of mineral waters

  2. Higher Education and the Minerals Boom: A View from the Regions

    Science.gov (United States)

    Bell, Philip

    2014-01-01

    This paper examines the impact of the minerals boom to date on the demand for higher education in Central Queensland, and the sustainability of higher education providers in high economic growth environments. Several datasets were used to examine changes in the demand for higher education among specific student groups within the region, the…

  3. An Opportunity on Exploiting of Geology and Mineral Resource Data for Regional Development

    International Nuclear Information System (INIS)

    Agus-Hendratno

    2004-01-01

    Indonesia archipelago have the very complex geo diversity. The complexity of geo diversity gives a lot of opportunity on exploiting of earth resources for society prosperity. In other side, the complexity of geology also gives a lot of resistance and various limitation at one particular region to expand. Hence, various data of geology as well as data of result of mapping of minerals resources (mapping at macro scale and also have detail scale) require to be managed and exploited maximally. Effort the exploiting also require various infrastructure which is concerning regulatory, technological, human resources being, market-drive of an economic geo material, social environment and culture which grow around geology data, and also availability and readiness of geology and mineral resources data. This study is expected can give a few description of how the geology and minerals resources data can be as reference in regional development planning. This paper was writed by assessment of description qualitative and comparative inter-region case study in various regency area, where writer have been involved to conduct the activity of geological mapping and mineral resources data and also involved by a discussion with a few officers of local government in so many opportunity. Some of the case study region for example : in Kampar Regency (Riau), Tanjung Jabung Timur Regency (Jambi), Biak Numfor Regency (Papua), Gunung Kidul Regency (Yogyakarta), Pacitan Regency (East Java), and also Klaten Regency (Central Java). (author)

  4. Uranium mineralization rules controlled by sedimentation in Bayanwula region in Erlian basin

    International Nuclear Information System (INIS)

    Lu Chao

    2012-01-01

    Uranium mineralization is closely related to sedimentation in Bayanwula region in Erlian Basin. Clarifying the relation of sedimentation and Uranium Mineralization Through detailed analysis of vertical sequences, stratigraphic correlation and the heterogeneity of sand body. Study show that the of development characteristics of sequences of Bayanwula region control the vertical positioning of favorable sand, the skeleton sand bodies of LST in upper Saihan formation is the most favorable reservoir space for uranium. Uranium mineralization is closely related with the heterogeneity of the sand bodies of upper Saihan formation. the heterogeneity of Sand body is mainly reflected in plane and vertical. In plane, with the research of the sand distributed system of upper Saihan formation, the change position of sandstone thickness and sand rate, the position of the variation of shape and trend of sand body, and the change position of sand body character and genesis are most favorable for uranium mineralization. In vertical, the number of layers and thickness of isolated barrier bed not only control the thickness of oxide sandstone. but also they are associated with the distribution of uranium mineralization; The evolution of sedimentary basins created Bayanwula uranium deposits. There is a second order sequence boundary between the upper Saihan formation and the Erlian formation of Late Cretaceous, which is a long-term exposure and erosion unconformity, resulting in the partly erosion of the upper Saihan formation, providing the best conditions of the penetration of the uranium-bearing oxygen water and the development of phreatic oxidation and interlayer oxidation zone. (author)

  5. First Principles Thermodynamics of Minerals at HP–HT Conditions: MgO as a Prototypical Material

    Directory of Open Access Journals (Sweden)

    Donato Belmonte

    2017-09-01

    Full Text Available Ab initio thermodynamic properties, equation of state and phase stability of periclase (MgO, B1-type structure have been investigated in a broad P–T range (0–160 GPa; 0–3000 K in order to set a model reference system for phase equilibria simulations under deep Earth conditions. Phonon dispersion calculations performed on large supercells using the finite displacement method and in the framework of quasi-harmonic approximation highlight the performance of the Becke three-parameter Lee-Yang-Parr (B3LYP hybrid density functional in predicting accurate thermodynamic functions (heat capacity, entropy, thermal expansivity, isothermal bulk modulus and phase reaction boundaries at high pressure and temperature. A first principles Mie–Grüneisen equation of state based on lattice vibrations directly provides a physically-consistent description of thermal pressure and P–V–T relations without any need to rely on empirical parameters or other phenomenological formalisms that could give spurious anomalies or uncontrolled extrapolations at HP–HT. The post-spinel phase transformation, Mg2SiO4 (ringwoodite = MgO (periclase + MgSiO3 (bridgmanite, is taken as a computational example to illustrate how first principles theory combined with the use of hybrid functionals is able to provide sound results on the Clapeyron slope, density change and P–T location of equilibrium mineral reactions relevant to mantle dynamics.

  6. FEATURES OF TERRITORIAL INTEGRATION OF MARKETING COMMUNICATIONS IN THE CAUCASIAN MINERAL WATERS REGION

    Directory of Open Access Journals (Sweden)

    Михаил Влидимирович Беляев

    2013-10-01

    Full Text Available The purpose of the work is to describe the situation taken place with integration of marketing communications in the region. The author conducted research aimed at identifying the most popular and effective forms of communication with the consumer, allowing in detail to characterize the state of the advertising market of Caucasian Mineral Waters. Information concluded in article may be used by companies present in the Caucasian Mineral Waters region, to form notion about the effectiveness of the regional channels of communication with customers and building a more efficient model of advertising policy, also its could be useful for specialists, which are working in marketing communication and advertising sphere.DOI: http://dx.doi.org/10.12731/2218-7405-2013-9-34

  7. Geology and potential of the formation of sandstone type uranium mineralization at Hatapang region, North Sumatera

    International Nuclear Information System (INIS)

    Ngadenin

    2013-01-01

    The Study based on geological setting of Hatapang region, North Sumatera, identified as a favourable area to the formation of sandstone type uranium mineralization. This characterized by the occurred of anomalous radioactivity, uranium contents of the upper cretaceous granite intrusions and radioactivity anomalous of tertiary sedimentary rocks deposited in terrestrial environments. The study is objective to find out the potential formation of sandstone type-uranium mineralization within tertiary sedimentary rocks based on data’s studies of geological, geochemical, mineralogy, radioactivity of rocks. Stratigraphy of Hatapang area of the oldest to youngest are quartz units (permian-carboniferous), sandstone units (upper Triassic), granite (upper cretaceous), conglomerate units (Lower –middle Miocene) and tuff units (Pleistocene). Hatapang’s granite is S type granite which is not only potential as source of radioactive minerals, particularly placer type monazite, but also potential as source rocks of sandstone type-uranium mineralization on lighter sedimentary rocks. Sedimentary rock of conglomerate units has potential as host rock, even though uranium did not accumulated in its rocks since the lack number of carbon as precipitant material and dissolved U"+"6 in water did not reduced into U"+"4 caused the uranium mineralization did not deposited. (author)

  8. Regional evolution of geological structure in south China and U mineralization

    International Nuclear Information System (INIS)

    Chen Guoda; Kang Zili; Shen Jinrui; Jin Yushu

    1992-01-01

    This paper states the development laws of regional geological structure of South China and its controlling effect on uranium deposit evolution, and the characteristics of rich uranium formation in different periods of geo-history are analysed. It also discusses the relationship between the distribution of time and space and tectonic structure and environmental vicissitudes. The rock-magma activities-the strong formation of the Diwa Era is of great significance to the formation of uranium deposits within the region, especially to the formation of a series of multi-genesis polygene uranium deposits which are a potential direction in which to look for minerals within the region

  9. LINEAMENTS MAP OF TURKEY FROM LANDSAT IMAGERY AND SELECTING TARGET AREAS FOR MINERAL EXPLORATION, RELATIONSHIP OF REGIONAL LINEAMENTS TO EARTHQUAKE EPICENTERS, MINERAL WATERS AND HOT SPRINGS

    Directory of Open Access Journals (Sweden)

    İsmail HENDEN

    1984-06-01

    Full Text Available Landsat coverage countrywide have been interpreted and a map of lineaments has been prepared. Circular features which are the surface expressions of deep or near   intrusions have  been  carefully mapped in order to investigate their relationship (if any to known mineralizations. From the outset it was postulated that the miner- alizations  are    located at the intersections of lineaments, especially in the vicinity of circular features.  To  test this hypo- thesis known mineralizations were placed on this map. It is noted that the metallic mineral deposits can be grouped into ten regions,  and out  of these,  two regions need to  be explored more intensively. In  some regions selected, locations of possible mineralizations were determined. Earthquake epicenters, mineral water sources and hot spring locations were placed on the  lineaments map. It is seen  that the hot springs and earthquake epicentres are located on regional fault systems.

  10. Characteristics of thermal-mineral waters in Backa region (Vojvodina) and their exploitation in spa tourism

    Energy Technology Data Exchange (ETDEWEB)

    Kosic, Kristina; Pivac, Tatjana; Romelic, Jovan; Lazic, Lazar; Stojanovic, Vladimir [Faculty of Science, Department of Geography, Tourism and Hotel Management, University of Novi Sad, Trg Dositeja Obradovica 3, 21000 Novi Sad (RS)

    2011-01-15

    Hydropower, biomass, biogas, biofuels, wind power, solar energy and geothermal energy are the major resources to provide Backa region with most of its. Backa extends between 45 16' and 46 22' of the northern latitude and 18 36' and 20 37' of the eastern longitude. It occupies the north-eastern part of Vojvodina, i.e. the most north-western part of the Republic of Serbia. That is historical-geographic territory bordered on the Danube on its western and eastern side, the Tisa on its eastern side and with the state border towards Hungary on the north. In this paper, the focus will be on renewable sources, specifically geothermal energy in Backa region. The paper analyzes the characteristics of thermal-mineral waters in Backa, the condition and possibilities of their exploitation in spa tourism, and in other economic branches. The tradition of thermo-mineral waters exploitation in spas and public baths is rather long. Today, this type of thermo-mineral waters exploitation in Backa is the widest spread. Permanent, i.e. continuous exploiters of thermal-mineral waters in Backa are primarily balneal-rehabilitation centres and exploiters using the water for technological purposes. (author)

  11. Mineral potential of clays that cover the gypsum deposits in Araripina-PE region

    International Nuclear Information System (INIS)

    Lira, B.B.; Anjos, I.F. dos; Rego, S.A.B.C.

    2011-01-01

    In the present work the applicability of the clays that cover the deposits of Gypsum Plaster in the region of Araripina - PE for use as the ceramic pigments and for bricks production in the red ceramic industry was analyzed. The clay minerals contained the illite, kaolinite and smectite, with high proportion of the last one. The possibility of industrial application of this mineral clay is considerable; however, the mining industries that mine and process the gypsum in the region do not take the clays into account as the potential mineral. In general, industries use the clay minerals in manufacturing processes or as key raw materials, or as the alternatives for some kinds of the chemical processing industries. This paper aims to highlight the potential of materials that cover the deposits of gypsum in reference. The material sampled from different deposit layers was characterized and the physical treatment of ore was applied. The results showed that the material analyzed can be used in various kinds of industry, such as the production of natural ceramic pigments. (author)

  12. Crystallographic Study of U-Th bearing minerals in Tranomaro, Anosy Region-Madagascar

    International Nuclear Information System (INIS)

    Sahoa, F.E.; Rabesiranana, N.; Raoelina Andriambololona; Geckeis, H.; Marquardt, C.; Finck, K.

    2011-01-01

    As an alternative to conventional fossil fuel, there is a renewed interest in the nuclear fuel to support increasing energy demand. New studies are then undertaken to characterize Madagascar U-Th bearing minerals. This is the case for the urano-thorianite bearing pyroxenites in the south East of Madagascar. In this region, several quarries were abandoned, after being mined by the French Atomic Energy Commission (C.E.A) in the fifties and sixties and are now explored by new mining companies. For this purpose, seven U-Th bearing mineral samples from old abandoned uranium quarries in Tranomaro, Amboasary Sud, Madagascar, have been collected. To determine the mineral microstructure, they were investigated for qualitative and quantitative identification of crystalline compounds using X-ray powder diffraction analytical method (XRD). Results showed that the U and Th compounds, as minor elements, are present in various crystalline structures. This is important to understand their environmental behaviours, in terms of crystallographic dispersion of U-Th minerals and their impacts on human health.

  13. Regional effects of ovariectomy and cadmium on bone mineral in ribs from aged female beagles

    International Nuclear Information System (INIS)

    Hurst, D.R.

    1991-01-01

    The purpose of this study was to evaluate effects of estrogen depletion and cadmium (Cd) on bone calcium and to determine if these effects were localized in specific regions of ribs. Fourteen female beagles with 45 Ca labeled skeletons were divided into four groups: sham controls (SO-); ovariectomized (OV-); shams exposed to Cd (SO+); ovariecomized exposed to Cd (OV+). Total Cd exposure period was 7 months, including 1 month by capsules and 6 months by drinking H 2 O. Ribs were taken at necropsy from 12 of the 14 dogs, and each rib was quartered. Wet, dry, and ash weights, as well as total Ca and 45 Ca content, were determined for each quarter. Analysis of ribs from control animals demonstrated that a given rib is heterogeneous in composition. One end appears to be less mineralized and more metabolically active than other regions. The OV- and OV+ mid-rib regions had significantly lower dry and ash weights than SO-. Total Ca contents of these same regions were also decreased in the OV- and OV+. The only significant change in Ca/dry and Ca/ash was observed when comparing OV+ to SO-. Analysis of treatment suggests that there are regional effects following ovariectomy increased the loss of bone mineral occurring as a result of ovariectomy. 30 refs., 1 fig

  14. Alteration mineral mapping in inaccessible regions using target detection algorithms to ASTER data

    International Nuclear Information System (INIS)

    Pour, A B; Hashim, M; Park, Y

    2017-01-01

    In this study, the applications of target detection algorithms such as Constrained Energy Minimization (CEM), Orthogonal Subspace Projection (OSP) and Adaptive Coherence Estimator (ACE) to shortwave infrared bands of the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) data was investigated to extract geological information for alteration mineral mapping in poorly exposed lithologies in inaccessible domains. The Oscar II coast area north-eastern Graham Land, Antarctic Peninsula (AP) was selected in this study to conduct a satellite-based remote sensing mapping technique. It is an inaccessible region due to the remoteness of many rock exposures and the necessity to travel over sever mountainous and glacier-cover terrains for geological field mapping and sample collection. Fractional abundance of alteration minerals such as muscovite, kaolinite, illite, montmorillonite, epidote, chlorite and biotite were identified in alteration zones using CEM, OSP and ACE algorithms in poorly mapped and unmapped zones at district scale for the Oscar II coast area. The results of this investigation demonstrated the applicability of ASTER shortwave infrared spectral data for lithological and alteration mineral mapping in poorly exposed lithologies and inaccessible regions, particularly using the image processing algorithms that are capable to detect sub-pixel targets in the remotely sensed images, where no prior information is available. (paper)

  15. Geotechnical aspects in the epicentral region of the 2011, Mw5.8 Mineral, Virginia earthquake

    Science.gov (United States)

    Green, Russell A.; Lasley, Samuel; Carter, Mark W.; Munsey, Jeffrey W.; Maurer, Brett W.; Tuttle, Martitia P.

    2015-01-01

    A reconnaissance team documented the geotechnical and geological aspects in the epicentral region of the Mw (moment magnitude) 5.8 Mineral, Virginia (USA), earthquake of 23 August 2011. Tectonically and seismically induced ground deformations, evidence of liquefaction, rock slides, river bank slumps, ground subsidence, performance of earthen dams, damage to public infrastructure and lifelines, and other effects of the earthquake were documented. This moderate earthquake provided the rare opportunity to collect data to help assess current geoengineering practices in the region, as well as to assess seismic performance of the aging infrastructure in the region. Ground failures included two marginal liquefaction sites, a river bank slump, four minor rockfalls, and a ~4-m-wide, ~12-m-long, ~0.3-m-deep subsidence on a residential property. Damage to lifelines included subsidence of the approaches for a bridge and a water main break to a heavily corroded, 5-cm-diameter valve in Mineral, Virginia. Observed damage to dams, landfills, and public-use properties included a small, shallow slide in the temporary (“working”) clay cap of the county landfill, damage to two earthen dams (one in the epicentral region and one further away near Bedford, Virginia), and substantial structural damage to two public school buildings.

  16. Field measurement of a Fermilab-built full scale prototype quadrupole magnet for the LHC interaction regions

    CERN Document Server

    Bossert, R; Di Marco, J; Fehér, S; Glass, H; Kerby, J S; Lamm, M J; Nobrega, A; Nicol, T H; Ogitsu, T; Orris, D; Page, T; Rabehl, Roger Jon; Sabbi, G L; Schlabach, P; Strait, J B; Sylvester, C D; Tartaglia, M; Tompkins, J C; Velev, G V; Zlobin, A V

    2002-01-01

    Superconducting low-beta quadrupole magnets for the interaction regions of the Large Hadron Collider have been developed by the US- LHC Accelerator Project. These 70 mm bore 5.5 m long quadrupoles are intended to operate in superfluid helium at 1.9 K with a nominal field gradient of 215 T/m. Following a series of 2 m long models, a full scale cryostated cold mass has been fabricated and cold tested at Fermilab. Magnetic field measurements of the prototype, including determination of the field axis using a single stretched wire, have been performed. These measurements and comparisons with results from the model magnets as well as field quality and alignment requirements are reported in this paper. (8 refs).

  17. Muscle strength and regional lean body mass influence on mineral bone health in young male adults.

    Science.gov (United States)

    Guimarães, Bianca Rosa; Pimenta, Luciana Duarte; Massini, Danilo Alexandre; Dos Santos, Daniel; Siqueira, Leandro Oliveira da Cruz; Simionato, Astor Reis; Dos Santos, Luiz Gustavo Almeida; Neiva, Cassiano Merussi; Pessôa Filho, Dalton Muller

    2018-01-01

    The relationship between muscle strength and bone mineral content (BMC) and bone mineral density (BMD) is supposed from the assumption of the mechanical stress influence on bone tissue metabolism. However, the direct relationship is not well established in younger men, since the enhancement of force able to produce effective changes in bone health, still needs to be further studied. This study aimed to analyze the influence of muscle strength on BMC and BMD in undergraduate students. Thirty six men (24.9 ± 8.6 y/o) were evaluated for regional and whole-body composition by dual energy X-ray absorptiometry (DXA). One repetition maximum tests (1RM) were assessed on flat bench-press (BP), lat-pull down (LPD), leg-curl (LC), knee extension (KE), and leg-press 45° (LP45) exercises. Linear regression modelled the relationships of BMD and BMC to the regional body composition and 1RM values. Measurements of dispersion and error (R2adj and standard error of estimate (SEE)) were tested, setting ρ at ≤0.05. The BMD mean value for whole-body was 1.12±0.09 g/cm2 and BMC attained 2477.9 ± 379.2 g. The regional lean mass (LM) in upper-limbs (UL) (= 6.80±1.21 kg) was related to BMC and BMD for UL (R2adj = 0.74, pBMC and BMD for LL (R2adj = 0.68, pBMC (R2adj = 0.47, pBMC (R2adj = 0.36, pBMC and BMD in young men, strengthening the relationship between force and LM, and suggesting both to parametrizes bone mineral health.

  18. Characterisation of mineral deposition systems associated with rock art in the Kimberley region of northwest Australia.

    Science.gov (United States)

    Green, Helen; Gleadow, Andrew; Finch, Damien

    2017-10-01

    This data article contains mineralogical and chemical data from mineral accretions sampled from rock art shelters in the Kimberley region of north west Australia. The accretions were collected both on and off pigment and engraved rock art of varying styles observed in the Kimberley with an aim of providing a thorough understanding of the formation and preservation of such materials in the context of dating [1]. This contribution includes processed powder X-ray Diffraction data, Scanning Electron Microscopy energy dispersive spectroscopy data, and Laser Ablation ICP-MS trace element mapping data.

  19. Architectural prototyping

    DEFF Research Database (Denmark)

    Bardram, Jakob Eyvind; Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2004-01-01

    A major part of software architecture design is learning how specific architectural designs balance the concerns of stakeholders. We explore the notion of "architectural prototypes", correspondingly architectural prototyping, as a means of using executable prototypes to investigate stakeholders...

  20. Survey of the mineral status of pastures and small ruminants in the West Region of Cameroon

    Directory of Open Access Journals (Sweden)

    Njwe, RM.

    1988-01-01

    Full Text Available Four dominant grass species (Hyparrhenia rufa, Melinis minutiflora, Pennisetum purpureum and Sporobolus africanus of natural pastures of the West Region of Cameroon were sampled at 60 sites between September and November of 1985. The grass samples were analysed for calcium, phosphorus, potassium, magnesium, sodium, iron, mangenese, copper and zinc. Serum was also collected from goats and sheep at the same locations where forages were sampled and analysed for calcium, phosphorus, magnesium, zinc and copper. Results showed that P, Mg, A/a, Zn and Cu in forages were generally below the critical level stipulated to satisfy the requirements of grazing livestock in the tropics. Calcium was inadequate in the sera of goats and sheep where as P, Mg, Zn and Cu were adequate. Use of salt licks to supplement intake of mineral elements from grasses by goats and sheep is necessary in the region.

  1. Au-As (lead) vein mineralizations of the Cevennes and Chataigneraie regions (French Massif Central). Isotopic characterization (Pb). Mineralizing role of granites in the setting up of these mineralizations

    International Nuclear Information System (INIS)

    Havard, M.L.

    1997-06-01

    This work has been carried out in the Frame of the national program 'Geofrance 3D' jointly organized by the French office for geologic and mining researches (BRGM), and the CNRS-INSU/DSPT3. Its aim is the study of the formation of gold-bearing mineralizations of the Variscan chain in the Cevennes and Chataigneraie regions (French Massif Central). In the Cevennes region, the gold-bearing veins are linked with the intrusion of the late-tectonic granodioritic plutons. The aim of this study is to determine the chronology of the mineralizing episodes and to analyze the relationship between the metal concentrates and the setting up of the granites. In the Chataigneraie region, the granites are intrusive in ortho- and para-gneiss series. The hydrothermal activity associated with the contact metamorphism should be responsible for the deposition of gold-bearing wolfram mineralization. The geochemistry of lead isotopes is used to determine the origin of metals in the sulfide mineralizations. The scanning electron microscopy (SEM) is used for the visualization of the microstructure heterogeneities of the minerals and for the quantitative chemical analysis of their successive para-geneses. The comparison between the results obtained in both regions allows to make a difference between their relative degree of erosion and their gold potentialities. (J.S.)

  2. Study on Regional Geology and Uranium Mineralization of Schwaner Mountains West and Central Kalimantan

    International Nuclear Information System (INIS)

    Soepradto-Tjokrokardono; Djoko-Soetarno; MS; Liliek-Subiantoro; Retno-Witjahyati

    2004-01-01

    Uranium occurrences indication in Kalimantan has been discovered at metamorphic and granites rocks of Schwaner Mountains as the radioactivity and geochemical anomalies. A regional geology of Schwaner Mountains show a watershed of West and East Kalimantan consist of Pinoh metamorphic rocks that was intruded by tonalitic and granitic batholite. The goal of this study is to observe the mechanism of the Uranium occurrences related to the regional tectonic, metamorphic rocks, tonalite and granitic batholite. Permokarbonaferrous metamorphic rocks as the big masses of roof pendant within tonalite mass. The metamorphic rocks originally as the big masses of roof pendant within tonalite mass. The metamorphic rocks originally derived from sedimentary process that produce a high content of uranium as well as a fine grained volcanic material. This uranium is deposited within neritic facies. Those sediments have been metamorphosed by low grade Abukuma regional metamorphism at the condition about 540 o C and 2000 bar. In early Cretaceous Tonalite of Sep auk intruded the rock and both metamorphics and tonalites. Those rocks were intruded by Late Cretaceous alkalin granite of Sukadana. Those crystalline rocks overlaid by an unconformity-related Kampari and Tebidah Formations that including within Melawi Group of Tertiary age. Uranium mineralization as the centimetric-metric veins related to tectonic N 100 o -110 o E and N 50 o E lineaments. Uranium was interpreted as a volcanic sedimentary origin, than it re mobilized by low grade regional metamorphism process. This enuchment process was carried out by fluor, boron and other metalliferous mineral within hydrothermal solutions of Sukadana granite. (author)

  3. Geology and associated mineral occurrences of the Araxa Group, Mossamedes Region, Goias, Brazil

    International Nuclear Information System (INIS)

    Simoes, L.S.A.

    1984-01-01

    In the region of Mossamedes, State of Goias, Brazil, the Precambrian metamorphic rocks of the Araxa group were mapped at the scale of 1:25,000, with emphasis on stratigraphic, structural, petrographic and economic aspects. These metamorphites represent a continous stratigraphic sequence which, from bottom to top can be subdivided into five informal lithostratigraphic units: 1) psamitic unit (quartzite, metaconglomerate); 2) psamitic-pelitic unit (quartzite, quartz schist, muscovite schist); 3) lower pelitic - volcanic unit (chlorite - biotite schist, fine grained blastoporphyritic gneiss, amphibolite and calc-schist); 4) upper pelitic - volcanic unit (garnet muscovite schist, biotite schist and gneiss, amphibolite, magnetite muscovite schist); 5) gneissic unit (epidote biotite gneiss, amphibolite). Three types of meta-intrusive rocks were found, besides basic dykes related to Mesozoic magmatism. Four phases of deformation affected the volcano-sedimentary sequence;D 1 , D 2 , D 3 and D 4 , each of them developing distinct deformational features. Barrowian type metamorphism increases progressively from North to South from the biotite zone to the garnet zone (greenschist facies), reaching the staurolite-kyanite zone (amphibolite facies). The magmatism throughout the Group's evolution consists of mafic to felsic volcanic activity, mustly intermediary, as well as three intrusive events. Gold, copper and zinc minerals of economic interest occur within the studied area. The gold mineralizations are related to the pelitic-volcanic sequences. Copper occurs in several rocks from the pelitic-volcanic and gneissic sequences. (Author) [pt

  4. Nitrogen mineralization in a high altitude ecosystem in the mediterranean phytogeographical region of Turkey.

    Science.gov (United States)

    Guleryuz, Gurcan; Gucel, Salih; Ozturk, Munir

    2010-07-01

    Interrelations exist in the terrestrial ecosystems between the plant type and characteristics of nutrient uptake. Annual net nitrogen mineralization in soils of different plant communities in the high altitude zone of Spil mountain located in the Mediterranean phytogeographical region of Turkey was investigated throughout one year by field incubation method. Seasonal fluctuations resulting from field incubation were markedly higher in autumn and spring than summer. These are mainly associated with the changes in soil moisture being at minimum in the Mediterranean summer. A significant correlation was developed between the net Nitrate (kg NO3(-)-N ha week(-1)) production and soil water content (p<0.05; r = 0.316 in soil of 0-5 cm; r = 0.312 in soil of 5-15 cm). The results showed that the annual productivity of nitrogen mineralization shows different values depending on communities. Annual net ammonium (NH4(+)-N) production in the soils of each community was negatively estimated. However annual net nitrate (NO3(-)-N) production (0-15 cm) was higher in grassland (27.8 kg ha y(-1)) and shrub (25.0 kg ha y(-1)) than forest (12.4 kg ha y(-1)) community. While annual net N(min) values were close to each other in grassland (14.5 kg ha y(-1)) and shrub (14.1 kg ha y(-1)), but negative in forest community (-3.6 kg ha y(-1)). The reasons for these differences are discussed.

  5. Mineral content in soil and pasture in bovine dairy herds of the Andean region of Ecuador

    Directory of Open Access Journals (Sweden)

    Luís Rodrigo Balarezo Urresta

    2017-10-01

    Full Text Available The objective of this research was to characterize the mineral status of the soil and pasture in of the Andean Ecuadorian region, during the rainy and dry periods, three dairy farms were used as study cases investigated him three dairy farms of the El Carchi province. They determined the chemical indicators of the soil and the pasture, the descriptive statisticians were calculated themselves and it was used a multifactorial ANOVA to determine the main factors affecting them on them, comparing means with Bonferroni and Duncan test. The soil classified as acid lightly, 100 % of the samples presented elevated levels of organic matter, NH4+, Mg, Cu, Zn, Fe and Mn. The farm had a significant effect on the pH, Ca, Mg, K, Cu, Fe, Mg and P, and the climatic period on the organic matter, NH4+, S, Cu and P. Pasture presented deficiencies of Mg, Zn and Na, the other minerals were above the critical limits. The farm affected the Ca, P, Mg, Na and Mn, and the climatic period the levels of Ca, K, Cu y Zn. In conclusion, 100 % soil samples presented high OM, slight acidity, low levels of Ca and high concentrations of NH4+, S, Mg, Cu, Zn and Mn. In pastures, there were diagnosed deficiencies of P, Cu and Zn, and their concentrations differed among farms and the two climatic periods of the year.

  6. Infrared Spectroscopy in the region X-Ray Diffraction and the mineral trioxide aggregate

    International Nuclear Information System (INIS)

    Barros, C.M.B.; Oliveira, S.V.; Silva, M.C.; Cartaxo, J.M.; Fook, M.V.L.

    2011-01-01

    In the nineties was introduced into the search field of biomaterials to mineral trioxide aggregate (MTA). It is a derivative of Portland cement with similar chemical properties and was initially developed as a root filling material in dentistry. This material is presented characteristics of mechanical, physical and biological meaningful when applied to biological environment. It was used to search a commercial MTA manipulated with distilled water and propylene glycol in order to verify chemical composition, infrared absorption bands and stages in the samples. The MTA has been characterized by XRF, XRD and FTIR. In X-ray fluorescence was found that the MTA has a characteristic composition of hydraulic cement. Through FTIR MTA mixed with water presents an enlargement in the absorption bands in the region 1467 and 873 cm-1. By means of XRD showed that there is no presence of toxic materials in the majority and secondary phases. (author)

  7. Stable isotopes use in hydrogeology studies of mineral and thermal waters (Lindoia region, Sao Paulo, Brazil)

    International Nuclear Information System (INIS)

    Yoshinaga, S.; Silva, A.A.K. de; Matsui, E.

    1991-01-01

    Deuterium and oxygen-18 studies were used to investigate the origin and the mineralizing processes of the mineral water and thermal water in Aguas de Lindoia and Lindoia, Brazilian municipal districts. (M.V.M.)

  8. Collaborative Prototyping

    DEFF Research Database (Denmark)

    Bogers, Marcel; Horst, Willem

    2014-01-01

    of the prototyping process, the actual prototype was used as a tool for communication or development, thus serving as a platform for the cross-fertilization of knowledge. In this way, collaborative prototyping leads to a better balance between functionality and usability; it translates usability problems into design......This paper presents an inductive study that shows how collaborative prototyping across functional, hierarchical, and organizational boundaries can improve the overall prototyping process. Our combined action research and case study approach provides new insights into how collaborative prototyping...... can provide a platform for prototype-driven problem solving in early new product development (NPD). Our findings have important implications for how to facilitate multistakeholder collaboration in prototyping and problem solving, and more generally for how to organize collaborative and open innovation...

  9. Uranium minerals in Upper Carboniferous rocks in the Nowa Ruda region

    International Nuclear Information System (INIS)

    Bareja, E.

    1981-01-01

    Results of mineralogical studies on uranium in Upper Carboniferous rocks (Glinik Beds - Westphalian C - D and Ludwikowice Beds - Stephanian) in the vicinities of Nowa Ruda (Central Sudetic Depression) are presented. Uranium mineralization is here related to sandstones and polymictic conglomerates with clay and clay-carbonate cement. The major uranium-bearing horizon was found in middle part of the Glinik Beds, and some increase in uranium content - at the base of that unit. In the case of Stephanian rocks, points with uranium mineralization were found in various parts of the Ludwikowice Beds sequence: in basal conglomerate horizon and platy sandstones. Uranium minerals mainly occur in cement of sandstones and conglomerates. They were mainly identified as uranium blende and minerals of the sulfate group - zippeite and uranopilite. Mineralized uranium-bearing horizons display mineral paragenesis typical of Upper Carboniferous rocks of the Central Sudetic Depression: uranium blende, pyrite, chalcopyrite, sphalerite and galena. (author)

  10. Au-Pt-Pd-U mineralization in the Coronation Hill-El Sherana region, NT

    International Nuclear Information System (INIS)

    Wyborn, L.

    1992-01-01

    In 1990 BMR's Minerals and Land Use program conducted an geochemical and geophysical survey to provide the best possible basis for estimating the resource potential of the Kakadu Conservation Zone. Combining the old and new data, an integrated model for the deposit types has been developed. Although differing in metal content, all mines and prospects of the Coronation Hill region share similar timing and structural controls, suggesting that they are related to one geochemical system. The presence or absence of U in the Au-Pt-Pd mineralisation appears related to geological differences, primarily in host-rock composition. U-bearing deposits are hosted mainly in carbonaceous shales, although some U is associated with chloritic zones. Deposits lacking U, best developed at Coronation Hill, occur in a broad range of host rocks, including quartz-feldspar porphyry, green tuffaceous shale, diorite, dolomite, and sedimentary breccias. Although seemingly diverse rock types, the common components of these U-poor host units are feldspar and/or carbonate. 1 tab., 3 figs

  11. Flotation of zinc and lead oxide minerals from Olkusz region calamine ores

    Directory of Open Access Journals (Sweden)

    Cichy Krystian

    2016-01-01

    Full Text Available The paper presents chemical and mineralogical characteristics of calamine ore from the Pomorzany mine. A flowsheet for recovery of sulphide minerals of zinc and lead in the form of the Zn-Pb bulk concentrate was presented. In the following part, preparation of the feed for flotation of Zn-Pb oxide minerals and optimal conditions for separation from it iron sulphide minerals, represented by marcasite, were determined. In the final section the results of flotation of Zn-Pb oxide minerals with anionic collector AM2 belonging to the hydroxyamide group of collectors and a cationic collector in the form of a coconut amine, being a mixture of primary aliphatic amines, were presented. Basing on the obtained results, a technological flowsheet for the recovery of Zn-Pb sulphide and oxide minerals from the calamine ore of the Pomorzany mine was presented.

  12. Characteristics of uranium mineralization and depositional system of host sediments, Bayantala basin, Inner Mongolia autonomous region

    International Nuclear Information System (INIS)

    Zhu Minqiang; Wu Rengui; Yu Dagan; Chen Anping; Shen Kefeng

    2003-01-01

    Based upon the research of basin fills at the Bayantala basin, the genetic facies of host sediments have been ascertained and the target beds and their range are delineated. The sand bodies of the Upper Member of Tengge'er Formation deposited in fan delta front is favorable to the formation of uranium mineralization of phreatic-interlayer oxidation. The Saihantala Fm deposited in fluvial system can be divided into Lower Member and Upper Member based on depositional microfacies and paleoclimate. The Lower Member of braided system is the most important target bed enriched in organic matter where basal-channel-type uranium mineralization occurs. Features of alteration and mineralization suggest that the early-stage and the late-stage uranium mineralization are related to phreatic oxidation and interlayer oxidation (roll-type) respectively. Meanwhile, the secondary reduction has superimposed over the earlier mineralization in the area caused by hydrocarbons raising along faults

  13. Mineral association composition and trace elements in urinary calculi in Ostrava region patients from 1978 to 2010

    Czech Academy of Sciences Publication Activity Database

    Martinec, Petr; Plasgura, P.; Machat, J.; Staněk, F.

    2011-01-01

    Roč. 10, č. 7 (2011), s. 462-462 ISSN 1569-9056. [EULIS 2011. London, 07.09.2011-10.09.2011] R&D Projects: GA ČR(CZ) GA203/09/1394 Institutional research plan: CEZ:AV0Z30860518 Keywords : urinary calculi * mineral association * chemical composition and trace elements Subject RIV: DD - Geochemistry Impact factor: 1.827, year: 2011 http://www.europeanurology.com/article/S1569-9056%2811%2961151-2/pdf/E03+Mineral+association,+composition+and+trace+elements+in+urinary+calculi+in+Ostrava+region+patients+from+1978+to+2010

  14. The Minimum Impact House : Applications of the Frankfurt Prototype for sustainable building in Cities of the European Rhine Region

    NARCIS (Netherlands)

    Drexler, H.; Jauslin, D.; Curiel, F.

    2010-01-01

    The Minimum Impact House in Frankfurt am Main is a sustainable solution for low cost living within city centers - a prototype typology with minimal footprint, built on a leftover urban space. The planning process itself became part of a scientific study. The ecological advantages of building in the

  15. Integration tests of prototype LVL1 calorimeter trigger CP/JEP ROD and LVL2 trigger Region-of-Interest Builder. Also visible in the photo are two further racks containing the demonstrator prototypes of the LVL1 CTP and the MUCTPI.

    CERN Multimedia

    Gee, N

    2001-01-01

    Integration tests of prototype LVL1 calorimeter trigger CP/JEP ROD and LVL2 trigger Region-of-Interest Builder. Also visible in the photo are two further racks containing the demonstrator prototypes of the LVL1 CTP and the MUCTPI.

  16. AlignMiner: a Web-based tool for detection of divergent regions in multiple sequence alignments of conserved sequences

    Directory of Open Access Journals (Sweden)

    Claros M Gonzalo

    2010-06-01

    Full Text Available Abstract Background Multiple sequence alignments are used to study gene or protein function, phylogenetic relations, genome evolution hypotheses and even gene polymorphisms. Virtually without exception, all available tools focus on conserved segments or residues. Small divergent regions, however, are biologically important for specific quantitative polymerase chain reaction, genotyping, molecular markers and preparation of specific antibodies, and yet have received little attention. As a consequence, they must be selected empirically by the researcher. AlignMiner has been developed to fill this gap in bioinformatic analyses. Results AlignMiner is a Web-based application for detection of conserved and divergent regions in alignments of conserved sequences, focusing particularly on divergence. It accepts alignments (protein or nucleic acid obtained using any of a variety of algorithms, which does not appear to have a significant impact on the final results. AlignMiner uses different scoring methods for assessing conserved/divergent regions, Entropy being the method that provides the highest number of regions with the greatest length, and Weighted being the most restrictive. Conserved/divergent regions can be generated either with respect to the consensus sequence or to one master sequence. The resulting data are presented in a graphical interface developed in AJAX, which provides remarkable user interaction capabilities. Users do not need to wait until execution is complete and can.even inspect their results on a different computer. Data can be downloaded onto a user disk, in standard formats. In silico and experimental proof-of-concept cases have shown that AlignMiner can be successfully used to designing specific polymerase chain reaction primers as well as potential epitopes for antibodies. Primer design is assisted by a module that deploys several oligonucleotide parameters for designing primers "on the fly". Conclusions AlignMiner can be used

  17. Prototyping Practice

    DEFF Research Database (Denmark)

    Ramsgaard Thomsen, Mette; Tamke, Martin

    2015-01-01

    This paper examines the role of the prototyping in digital architecture. During the past decade, a new research field has emerged exploring the digital technology’s impact on the way we think, design and build our environment. In this practice the prototype, the pavilion, installation or demonstr......This paper examines the role of the prototyping in digital architecture. During the past decade, a new research field has emerged exploring the digital technology’s impact on the way we think, design and build our environment. In this practice the prototype, the pavilion, installation...

  18. Association of the serotonin transporter-linked polymorphic region genotype with lower bone mineral density.

    Science.gov (United States)

    Lapid, M I; Kung, S; Frye, M A; Biernacka, J M; Geske, J R; Drake, M T; Jankowski, M D; Clarke, B L

    2017-08-22

    The serotonin transporter-linked polymorphic region (5-HTTLPR) of the serotonin transporter gene (SLC6A4) S allele is linked to pathogenesis of depression and slower response to selective serotonin reuptake inhibitors (SSRIs); depression and SSRIs are independently associated with bone loss. We aimed to determine whether 5-HTTLPR was associated with bone loss. This cross-sectional study included psychiatric patients with both 5-HTTLPR analysis and bone mineral density (BMD) assessment (hip and spine Z-scores if age <50 years and T-scores if ⩾50 years). BMD association with 5-HTTLPR was evaluated under models with additive allele effects and dominant S allele effects using linear regression models. Patients were stratified by age (<50 and ⩾50 years) and sex. Of 3016 patients with 5-HTTLPR genotyping, 239 had BMD assessments. Among the younger patients, the S allele was associated with lower Z-scores at the hip (P=0.002, dominant S allele effects; P=0.004, additive allele effects) and spine (P=0.0006, dominant S allele effects; P=0.01, additive allele effects). In sex-stratified analyses, the association of the S allele with lower BMD in the younger patients was also significant in the subset of women (P⩽0.003 for both hip and spine BMD under the additive allele effect model). In the small group of men younger than 50 years, the S allele was marginally associated with higher spine BMD (P=0.05). BMD T-scores were not associated with 5-HTTLPR genotypes in patients 50 years or older. The 5-HTTLPR variants may modify serotonin effects on bone with sex-specific effects.

  19. [Response of mineralization of dissolved organic carbon to soil moisture in paddy and upland soils in hilly red soil region].

    Science.gov (United States)

    Chen, Xiang-Bi; Wang, Ai-Hua; Hu, Le-Ning; Huang, Yuan; Li, Yang; He, Xun-Yang; Su, Yi-Rong

    2014-03-01

    Typical paddy and upland soils were collected from a hilly subtropical red-soil region. 14C-labeled dissolved organic carbon (14C-DOC) was extracted from the paddy and upland soils incorporated with 14C-labeled straw after a 30-day (d) incubation period under simulated field conditions. A 100-d incubation experiment (25 degrees C) with the addition of 14C-DOC to paddy and upland soils was conducted to monitor the dynamics of 14C-DOC mineralization under different soil moisture conditions [45%, 60%, 75%, 90%, and 105% of the field water holding capacity (WHC)]. The results showed that after 100 days, 28.7%-61.4% of the labeled DOC in the two types of soils was mineralized to CO2. The mineralization rates of DOC in the paddy soils were significantly higher than in the upland soils under all soil moisture conditions, owing to the less complex composition of DOC in the paddy soils. The aerobic condition was beneficial for DOC mineralization in both soils, and the anaerobic condition was beneficial for DOC accumulation. The biodegradability and the proportion of the labile fraction of the added DOC increased with the increase of soil moisture (45% -90% WHC). Within 100 days, the labile DOC fraction accounted for 80.5%-91.1% (paddy soil) and 66.3%-72.4% (upland soil) of the cumulative mineralization of DOC, implying that the biodegradation rate of DOC was controlled by the percentage of labile DOC fraction.

  20. Structure and chemical characteristics of natural mineral deposit Terbunskaya (Lipetsk region, Russia)

    Energy Technology Data Exchange (ETDEWEB)

    Motyleva, S., E-mail: motyleva-svetlana@mail.ru; Mertvishcheva, M. [All-Russian Horticular Institute for Breeding, Agrotechnology and Nursery Russian Academy of Agricultural Sciences, Moskow (Russian Federation); Shchuchka, R.; Gulidova, V. [Yelets state university named after I. A. Bunin, Yelets (Russian Federation)

    2015-07-22

    New knowledge about the mineralogical features Terbunsky mineral. Investigated 5 fractions isolated from the incision (2-2,5 m). Terbunskaya deposit belongs to minerals Santonian age. Scanning electron microscopy and energy dispersive analysis of fractions isolated studied in detail. In the coarse fractions found ancient organic remains of algae and micro-organisms that have been sedimented together with the mineral component during geological periods. The share of organic inclusions does not exceed 1.5%. Chemical composition confirms the presence of silicon and carbonate organisms. Advantageously proportion of minerals having a layered structure with a plurality of micro and nano pore size 600 - 80-nm and an average chemical composition (wt%): Na (0,64), Mg (0,54), Al (13.48), Si (27 57), K (2.39) Ca (0.75)

  1. Total and regional bone mineral content in healthy Spanish subjects by dual-energy X-ray absorptiometry

    International Nuclear Information System (INIS)

    Aguado Henche, S.; Rodriguez Torres, R.; Clemente de Arriba, C.; Gomez Pellico, L.

    2008-01-01

    This is an observational cross-sectional study. The aim of the present study was to describe and analyze patterns of change in total and regional bone mineral content in relation to age and gender in a sedentary Spanish sample population (from the Community of Madrid). The age range of the sample population was from birth to 80 years. One thousand one hundred twenty healthy subjects were recruited and divided into 16 groups according to age. Each subject underwent whole-body densitometry using dual-energy X-ray absorptiometry. An analysis was made of the amount of bone mineral content (BMC) in the whole body and in different regions: the head, trunk, upper limbs, and lower limbs. Gender differences in mean values for upper limbs and lower limbs are statistically significant between 16 and 70 years of age. For the head and trunk, the mean BMC values show the most significant gender differences between 16 and 25 years of age (p≤0.001). Total bone mineral content (TBMC) and TBMC-to-height ratio show significant gender differences between 16 and 70 years of age. In females, TBMC values increase up to 20 years of age and in males up to 25 years of age. We have determined an evolutionary normal pattern of bone mineral content in urban Spanish people. (orig.)

  2. Total and regional bone mineral content in healthy Spanish subjects by dual-energy X-ray absorptiometry

    Energy Technology Data Exchange (ETDEWEB)

    Aguado Henche, S.; Rodriguez Torres, R.; Clemente de Arriba, C.; Gomez Pellico, L. [Universidad de Alcala, Departamento de Anatomia y Embriologia Humana, Facultad de Medicina, Alcala de Henares, Madrid (Spain)

    2008-11-15

    This is an observational cross-sectional study. The aim of the present study was to describe and analyze patterns of change in total and regional bone mineral content in relation to age and gender in a sedentary Spanish sample population (from the Community of Madrid). The age range of the sample population was from birth to 80 years. One thousand one hundred twenty healthy subjects were recruited and divided into 16 groups according to age. Each subject underwent whole-body densitometry using dual-energy X-ray absorptiometry. An analysis was made of the amount of bone mineral content (BMC) in the whole body and in different regions: the head, trunk, upper limbs, and lower limbs. Gender differences in mean values for upper limbs and lower limbs are statistically significant between 16 and 70 years of age. For the head and trunk, the mean BMC values show the most significant gender differences between 16 and 25 years of age (p{<=}0.001). Total bone mineral content (TBMC) and TBMC-to-height ratio show significant gender differences between 16 and 70 years of age. In females, TBMC values increase up to 20 years of age and in males up to 25 years of age. We have determined an evolutionary normal pattern of bone mineral content in urban Spanish people. (orig.)

  3. Geochemistry of thermal/mineral waters in the Clear Lake region, California, and implications for hot dry rock geothermal development

    Energy Technology Data Exchange (ETDEWEB)

    Goff, F.; Adams, A.I.; Trujillo, P.E.; Counce, D.; Mansfield, J.

    1993-02-01

    Thermal/mineral waters of the Clear Lake region are broadly classified as thermal meteoric and connote types based on chemical and isotopic criteria. Ratios of conservative components such as B/Cl are extremely different among all thermal/mineral waters of the Clear Lake region except for clusters of waters emerging from specific areas such as the Wilbur Springs district and the Agricultural Park area south of Mt. Konocti. In contrast, ratios of conservative components in large, homogeneous geothermal reservoirs are constant. Stable isotope values of Clear Lake region waters show a mixing trend between thermal meteoric and connote end-members. The latter end-member has enriched [delta]D as well as enriched d[sup l8]O, very different from typical high-temperature geothermal reservoir waters. Tritium data and modeling of ages indicate most Clear Lake region waters are 500 to > 10,000 yr., although mixing of old and young components is implied by the data. The age of end-member connate water is probably > 10,000 yr. Subsurface equilibration temperature of most thermal/mineral waters of the Clear Lake region is [le] 150[degrees]C based on chemical geothermometers but it is recognized that Clear Lake region waters are not typical geothermal fluids and that they violate rules of application of many geothermometers. The combined data indicate that no large geothermal reservoir underlies the Clear Lake region and that small localized reservoirs have equilibration temperatures [le] 150[degrees]C (except for Sulphur Bank Mine). Hot dry rock technologies are the best way to commercially exploit the known high temperatures existing beneath the Clear Lake region, particularly within the main Clear Lake volcanic field.

  4. Access-enabling architectures : new hybrid multi-modal spatial prototypes towards resource and social sustainability : USDOT Region V Regional University Transportation Center final report.

    Science.gov (United States)

    2016-12-19

    The efforts of this project aim to capture and engage these potentials through a design-research method that incorporates a top down, data-driven approach with bottom-up stakeholder perspectives to develop prototypical scenario-based design solutions...

  5. Unikabeton Prototype

    DEFF Research Database (Denmark)

    Søndergaard, Asbjørn; Dombernowsky, Per

    2011-01-01

    The Unikabeton prototype structure was developed as the finalization of the cross-disciplinary research project Unikabeton, exploring the architectural potential in linking the computational process of topology optimisation with robot fabrication of concrete casting moulds. The project was elabor......The Unikabeton prototype structure was developed as the finalization of the cross-disciplinary research project Unikabeton, exploring the architectural potential in linking the computational process of topology optimisation with robot fabrication of concrete casting moulds. The project...... of Architecture was to develop a series of optimisation experiments, concluding in the design and optimisation of a full scale prototype concrete structure....

  6. Evaluation of Digital Classification of Polarimetric SAR Data for Iron-Mineralized Laterites Mapping in the Amazon Region

    Directory of Open Access Journals (Sweden)

    Cleber G. Oliveira

    2013-06-01

    Full Text Available This study evaluates the potential of C- and L-band polarimetric SAR data for the discrimination of iron-mineralized laterites in the Brazilian Amazon region. The study area is the N1 plateau located on the northern border of the Carajás Mineral Province, the most important Brazilian mineral province which has numerous mineral deposits, particularly the world’s largest iron deposits. The plateau is covered by low-density savanna-type vegetation (campus rupestres which contrasts visibly with the dense equatorial forest. The laterites are subdivided into three units: chemical crust, iron-ore duricrust, and hematite, of which only the latter two are of economic interest. Full polarimetric data from the airborne R99B sensor of the SIVAM/CENSIPAM (L-band system and the RADARSAT-2 satellite (C-band were evaluated. The study focused on an assessment of distinct schemes for digital classification based on decomposition theory and hybrid approach, which incorporates statistical analysis as input data derived from the target decomposition modeling. The results indicated that the polarimetric classifications presented a poor performance, with global Kappa values below 0.20. The accuracy for the identification of units of economic interest varied from 55% to 89%, albeit with high commission error values. In addition, the results using L-band were considered superior compared to C-band, which suggest that the roughness scale for laterite discrimination in the area is nearer to L than to C-band.

  7. Solution Prototype

    DEFF Research Database (Denmark)

    Efeoglu, Arkin; Møller, Charles; Serie, Michel

    2013-01-01

    This paper outlines an artifact building and evaluation proposal. Design Science Research (DSR) studies usually consider encapsulated artifact that have relationships with other artifacts. The solution prototype as a composed artifact demands for a more comprehensive consideration in its systematic...... environment. The solution prototype that is composed from blending product and service prototype has particular impacts on the dualism of DSR’s “Build” and “Evaluate”. Since the mix between product and service prototyping can be varied, there is a demand for a more agile and iterative framework. Van de Ven......’s research framework seems to fit this purpose. Van de Ven allows for an iterative research approach to problem solving with flexible starting point. The research activity is the result between the iteration of two dimensions. This framework focuses on the natural evaluation, particularly on ex...

  8. Software Prototyping

    Science.gov (United States)

    Del Fiol, Guilherme; Hanseler, Haley; Crouch, Barbara Insley; Cummins, Mollie R.

    2016-01-01

    Summary Background Health information exchange (HIE) between Poison Control Centers (PCCs) and Emergency Departments (EDs) could improve care of poisoned patients. However, PCC information systems are not designed to facilitate HIE with EDs; therefore, we are developing specialized software to support HIE within the normal workflow of the PCC using user-centered design and rapid prototyping. Objective To describe the design of an HIE dashboard and the refinement of user requirements through rapid prototyping. Methods Using previously elicited user requirements, we designed low-fidelity sketches of designs on paper with iterative refinement. Next, we designed an interactive high-fidelity prototype and conducted scenario-based usability tests with end users. Users were asked to think aloud while accomplishing tasks related to a case vignette. After testing, the users provided feedback and evaluated the prototype using the System Usability Scale (SUS). Results Survey results from three users provided useful feedback that was then incorporated into the design. After achieving a stable design, we used the prototype itself as the specification for development of the actual software. Benefits of prototyping included having 1) subject-matter experts heavily involved with the design; 2) flexibility to make rapid changes, 3) the ability to minimize software development efforts early in the design stage; 4) rapid finalization of requirements; 5) early visualization of designs; 6) and a powerful vehicle for communication of the design to the programmers. Challenges included 1) time and effort to develop the prototypes and case scenarios; 2) no simulation of system performance; 3) not having all proposed functionality available in the final product; and 4) missing needed data elements in the PCC information system. PMID:27081404

  9. GEOINFORMATIONAL ANALYSIS OF CHANGING BOUNDARIES OF FOREST TRACTS OF THE REGION OF CAUCASIAN MINERAL WATERS OF STAVROPOL TERRITORY

    Directory of Open Access Journals (Sweden)

    O. S. Anikeeva

    2017-01-01

    Full Text Available Deterioration of the state of forests and illegal logging are a global problem of our time. The region of the Caucasian Mineral Waters has a small number of forest areas, so the need to introduce new methods for analyzing the state of forests is an important task in the conservation of forests in this area. One such method is geoinformational analysis. For the survey, the geoinformation systems ScanEx Image Processor 4.0, Mapinfo Professional 12, QGIS 2.8 have been used.The species composition of the largest forest tracts of the Caucasian Mineral Waters is considered. The main reasons for changing the boundaries of forest areas have been determined. A geoinformational analysis of the changes in the boundaries of the forest tracts of the region has been carried out using remote sensing data for the period from 1987 to 2014. For the analysis, space images of the Landsat 5 and 8 system were used for the period from 1987 to 2014.A classification of multi-temporal optical images has been made, which allowed obtaining the values of forest areas in different years and to calculate their percentage of forest cover. In 1987, the forest area of the region was 35.2 thousand hectares; in 1998, 41.99 thousand hectares, and by 2014 it was reduced to 33.16 thousand hectares.On the basis of the data obtained, a series of maps characterizing the forests of the Caucasian Mineral Waters in different years has been constructed.The conducted study led to the conclusion that the main changes in the forest boundaries occurred in the Mashuk, Lysoy, Zheleznaya, Beshtau, Verblud and Bik mountains. This is due primarily to the proximity to the most densely populated cities in the region: Pyatigorsk, Zheleznovodsk, Essentuki and the city of Mineralnye Vody.

  10. Identification of Oxide Compound in Dolomite Mineral from Aceh Tamiang Region

    Directory of Open Access Journals (Sweden)

    Nirmala Sari

    2013-08-01

    Full Text Available Indonesia has abundant mineral especially carbonate-based mineral, ike dolomite. Particularly in Aceh province's, the largest dolomite deposits is available in Aceh Tamiang district around 1.9 billion tons. Unfortunately, current use of dolomite in the industry and other applications is still limited. In this work we report the advanced preparation of dolomite using calcinations method. Whereas, with this method, the dolomite mineral can be processed into calcium and magnesium oxide which has a very wide field of application and higher values. To obtain optimal results, we also identify the effect of temperature on the formation of oxide compounds. Preliminary study using XRF founded that dolomite in village Selamat is known as the highest concentration of CaO (61.20% followed by MgO (25.28%. It is also showed that the main phase obtained by XRD is dolomite (CaMg(CO32. Furthermore, after the calcinations process at 700 °C, it was founded that the formation of dolomite were CaCO3 and MgO, whereas at temperatures of 900 °C mostly the CaCO3 has decomposed into CaO. SEM observations showed that dolomite has the composition of particles distributed homogeneously along the particle agglomerate when it calcinations.

  11. The Complex Stratigraphy of the Highland Crust in the Serenitatis Region of the Moon Inferred from Mineral Fragment Chemistry

    Science.gov (United States)

    Ryder, Graham; Norman, Marc D.; Taylor, G. Jeffrey

    1997-01-01

    Large impact basins are natural drill holes into the Moon, and their ejecta carries unique information about the rock types and stratigraphy of the lunar crust. We have conducted an electron microprobe study of mineral fragments in the poikilitic melt breccias collected from the Taurus Mountains at the Apollo 17 landing site. These breccias are virtually unanimously agreed to be impact melt produced in the Serenitatis impact event. They contain lithic fragments and much more abundant mineral fragments of crustal origin. We have made precise microprobe analyses of minor element abundances in fragments of olivine, pyroxene, and plagioclase to provide new information on the possible source rocks and the crustal stratigraphy in the Serenitatis region. These data were also intended to elucidate the nature of the cryptic geochemical component in breccias such as these with low-K Fra Mauro basalt compositions. We chose the finest-grained (i.e., most rapidly quenched) breccias for study, to avoid reacted and partly assimilated fragments as much as possible. Most of the mineral fragments appear to have been derived from rocks that would fall into the pristine igneous Mg-suite as represented by lithic fragments in the Apollo collection, or reasonable extensions of it. Gabbroic rocks were more abundant in the target stratigraphy than is apparent from the Apollo sample collection. Some pyroxene and plagiociase, but probably not much olivine, could be derived from feldspathic granulites, which are metamorphosed polymict breccias. Some mineral fragments are from previously unknown rocks. These include highly magnesian olivines (up to Fo(sub 94)), possibly volcanic in origin, that exacerbate the difficulty in explaining highly magnesian rocks in the lunar crust. It appears that some part of the lunar interior has an mg*(= 100 x Mg/(Mg/Fe) atomic) greater than the conventional bulk Moon value of 80-84. Other volcanic rocks, including mare basalts, and rapidly- cooled impact melt

  12. Proximate, mineral composition and antioxidant activity of traditional small millets cultivated and consumed in Rayalaseema region of south India.

    Science.gov (United States)

    Vali Pasha, Kotwal; Ratnavathi, Chamarthy Venkata; Ajani, Jayanna; Raju, Dugyala; Manoj Kumar, Sriramoju; Beedu, Sashidhar Rao

    2018-01-01

    Millets are a diverse group of small seeded grasses, widely grown around the world as cereal foods. This communication details the proximate, mineral profile and antioxidant activity of six different small millets (Finger, Foxtail, Proso, Little, Barnyard and Kodo millets) and their 21 cultivars that are traditionally cultivated and consumed in the region of Ralayaseema, south India. The proximate analysis revealed that these millets are rich in protein, fat, ash (mineral), total dietary fibre and total phenols with appreciable antioxidant activity. However, starch and amylose content was comparatively lower as compared to major millet sorghum. ICP-MS analysis of small millets demonstrated that they are rich in minerals such as Ca, P, K, Mg, Fe, Cu, Zn, Mn, Cr, Mo and Se. Finger and kodo millets were found to be nutritionally superior over other small millets. The results suggest that small millets have a potential to provide food security and can combat micronutrient malnutrition. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  13. The role of lateral boundary conditions in simulations of mineral aerosols by a regional climate model of Southwest Asia

    Energy Technology Data Exchange (ETDEWEB)

    Marcella, Marc Pace [Ralph M. Parsons Laboratory, Department of Civil and Environmental Engineering, Cambridge, MA (United States); Massachusetts Institute of Technology, Cambridge, Massachusetts (United States); Eltahir, Elfatih A.B. [Massachusetts Institute of Technology, Cambridge, Massachusetts (United States)

    2012-01-15

    The importance of specifying realistic lateral boundary conditions in the regional modeling of mineral aerosols has not been examined previously. This study examines the impact of assigning values for mineral aerosol (dust) concentrations at the lateral boundaries of Regional Climate Model version 3 (RegCM3) and its aerosol model over Southwest Asia. Currently, the dust emission module of RegCM3 operates over the interior of the domain, allowing dust to be transported to the boundaries, but neglecting any dust emitted at these points or from outside the domain. To account for possible dust occurring at, or entering from the boundaries, mixing ratios of dust concentrations from a larger domain RegCM3 simulation are specified at the boundaries of a smaller domain over Southwest Asia. The lateral boundary conditions are monthly averaged concentration values ({mu}g of dust per kg of dry air) resolved in the vertical for all four dust bin sizes within RegCM3's aerosol model. RegCM3 simulations with the aerosol/dust model including lateral boundary conditions for dust are performed for a five year period and compared to model simulations without prescribed dust concentrations at the boundaries. Results indicate that specifying boundary conditions has a significant impact on dust loading across the entire domain over Southwest Asia. More specifically, a nearly 30% increase in aerosol optical depth occurs during the summer months from specifying realistic dust boundary conditions, bringing model results closer to observations such as MISR. In addition, smaller dust particles at the boundaries have a more important impact than large particles in affecting the dust loading within the interior of this domain. Moreover, increases in aerosol optical depth and dust concentrations within the interior domain are not entirely caused by inflow from the boundaries; results indicate that an increase in the gradient of concentration at the boundaries causes an increase of

  14. Laboratory estimate of the regional shortwave refractive index and single scattering albedo of mineral dust from major sources worldwide

    Science.gov (United States)

    Di Biagio, C.; Formenti, P.; Caponi, L.; Cazaunau, M.; Pangui, E.; Journet, E.; Nowak, S.; Caquineau, S.; Andreae, M. O.; Kandler, K.; Saeed, T.; Piketh, S.; Seibert, D.; Williams, E.; Balkanski, Y.; Doussin, J. F.

    2017-12-01

    Mineral dust is one of the most abundant aerosol species in the atmosphere and strongly contributes to the global and regional direct radiative effect. Still large uncertainties persist on the magnitude and overall sign of the dust direct effect, where indeed one of the main unknowns is how much mineral dust absorbs light in the shortwave (SW) spectral range. Aerosol absorption is represented both by the imaginary part (k) of the complex refractive index or the single scattering albedo (SSA, i.e. the ratio of the scattering to extinction coefficient). In this study we present a new dataset of SW complex refractive indices and SSA for mineral dust aerosols obtained from in situ measurements in the 4.2 m3 CESAM simulation chamber at LISA (Laboratoire Interuniversitaire des Systemes Atmospheriques) in Créteil, France. Investigated dust aerosol samples were issued from major desert sources worldwide, including the African Sahara and Sahel, Eastern Asia, the Middle East, Southern Africa, Australia, and the Americas, with differing iron oxides content. Results from the present study provide a regional mapping of the SW absorption by dust and show that the imaginary part of the refractive index largely varies (by up to a factor 6, 0.003-0.02 at 370 nm and 0.001-0.003 at 950 nm) for the different source areas due to the change in the particle iron oxide content. The SSA for dust varies between 0.75-0.90 at 370 nm and 0.95-0.99 at 950 nm, with the largest absorption observed for Sahelian and Australian dust aerosols. Our range of variability for k and SSA is well bracketed by already published literature estimates, but suggests that regional‒dependent values should be used in models. The possible relationship between k and the dust iron oxides content is investigated with the aim of providing a parameterization of the regional‒dependent dust absorption to include in climate models.

  15. MIND performance and prototyping

    International Nuclear Information System (INIS)

    Cervera-Villanueva, A.

    2008-01-01

    The performance of MIND (Magnetised Iron Neutrino Detector) at a neutrino factory has been revisited in a new analysis. In particular, the low neutrino energy region is studied, obtaining an efficiency plateau around 5 GeV for a background level below 10 -3 . A first look has been given into the detector optimisation and prototyping

  16. Techniques for processing remote field eddy current signals from bend regions of steam generator tubes of prototype fast breeder reactor

    Energy Technology Data Exchange (ETDEWEB)

    Thirunavukkarasu, S. [Non Destructive Evaluation Division, Indira Gandhi Centre for Atomic Research, Kalpakkam, TN 603 102 (India); Rao, B.P.C., E-mail: bpcrao@igcar.gov.in [Non Destructive Evaluation Division, Indira Gandhi Centre for Atomic Research, Kalpakkam, TN 603 102 (India); Jayakumar, T.; Raj, Baldev [Non Destructive Evaluation Division, Indira Gandhi Centre for Atomic Research, Kalpakkam, TN 603 102 (India)

    2011-04-15

    Steam generator (SG) is one of the most critical components of sodium cooled fast breeder reactor. Remote field eddy current (RFEC) technique has been chosen for in-service inspection (ISI) of these ferromagnetic SG tubes made of modified 9Cr-1Mo steel (Grade 91). Expansion bends are provided in the SGs to accommodate differential thermal expansion. During ISI using RFEC technique, in expansion bend regions, exciter-receiver coil misalignment, bending stresses, probe wobble and magnetic permeability variations produce disturbing noise hindering detection of defects. Fourier filtering, cross-correlation and wavelet transform techniques have been studied for noise reduction as well as enhancement of RFEC signals of defects in bend regions, having machined grooves and localized defects. Performance of these three techniques has been compared using signal-to-noise ratio (SNR). Fourier filtering technique has shown better performance for noise reduction while cross-correlation technique has resulted in significant enhancement of signals. Wavelet transform technique has shown the combined capability of noise reduction and signal enhancement and resulted in unambiguous detection of 10% of wall loss grooves and localized defects in the bend regions with SNR better than 7 dB.

  17. Miners, peasants and entrepreneurs : Regional development in the Central Highlands of Peru

    NARCIS (Netherlands)

    Long, N.; Roberts, B.

    1984-01-01

    This volume traces the development of the central highlands, one of Peru's major mining regions. It draws on extensive fieldwork carried out in Peru between 1970 and 1982, spanning a reforming military government, reaction and a return to civilian politics under Belaunde. Through historical material

  18. The research of the quantitative prediction of the deposits concentrated regions of the large and super-large sized mineral deposits in China

    International Nuclear Information System (INIS)

    Zhao Zhenyu; Wang Shicheng

    2003-01-01

    By the general theory and method of mineral resources prognosis of synthetic information, the locative and quantitative prediction of the large and super-large sized mineral deposits of solid resources of 1 : 5,000,000 are developed in china. The deposit concentrated regions is model unit, the anomaly concentrated regions is prediction unit. The mineral prognosis of synthetic information is developed on GIS platform. The technical route and work method of looking for the large and super-large sized mineral resources and basic principle of compiling attribute table of the variables and the response variables are mentioned. In research of prediction of resources quantity, the locative and quantitative prediction are processed by separately the quantification theory Ⅲ and the corresponding characteristic analysis, two methods are compared. It is very important for resources prediction of western ten provinces in china, it is helpful. (authors)

  19. STUDY ON THE PHYSICOCHEMICAL, ANTIOXIDANT PROPERTIES AND MINERAL CONTENT OF FIVE HONEYS PRODUCED IN THE CENTRAL REGION OF ALGERIA

    Directory of Open Access Journals (Sweden)

    MOUNIR HABATI

    2017-06-01

    Full Text Available The present study evaluated the physicochemical, antioxidant properties and mineral content of five Honeys from the Central Region of Algeria (Laghouat. Physicochemical properties were examined according to the official methods of analysis of AOAC (Association of Official Analytical Chemists; antioxidant activities were determined by DPPH (2,2-diphenyl-1-picrylhydrazyl and FRAP (Ferric reducing ability of plasma assays, the minerals were analyzed by atomic absorption spectrometry. The results compared to those recommended by Codex Alimentarius indicated that the quality of the tested honey was very good. The samples exhibited good antioxidant activity. A linear positive relationship existed between antioxidant activity and total phenolics (R2 = 0.95/flavonoids (R2 = 0.99. The analyzed honey samples possess valuable antioxidants for culinary and medicinal uses. The analysis revealed the presence of (K 220.88 ± 1.72 ppm, (Na 85.84 ± 1.72 ppm, (Fe 0.1922 ± 0.47 ppm, (Co 0.9144 ± 1.63 ppm, (Cu 0.1252 ± 1.76 ppm and nickel (Ni 0.0463 ± 0.10 ppm in the collected samples. Toxic elements identified in the studied honeys are safe because they are below the maximum residual limit. Therefore, these results indicate that the areas of production of these honeys are unpolluted by the toxic elements.

  20. The occurrence of ferropyrosmalite in the mineralized breccias from Igarape Bahia (North region, Brazil) Au-Cu (± ETR-U) deposit, Carajas mineral Province

    International Nuclear Information System (INIS)

    Tazava, Edison; Gomes, Newton Souza; Oliveira, Claudinei Gouveia de

    1999-01-01

    In the last years, several works report the presence of pyrosmalite mineral series [(Fe, Mn) 8 Si 6 O 15 (OH, Cl) 10 ] commonly associated with volcanic exhalative massive sulphide or Fe-Mn metamorphosed deposits. In this paper, we present the inedit occurrence of ferropyrosmalite in the Au-Cu (± REE-U) of Igarape Bahia deposit, located in the Au-Cu district of the Carajas Mineral Province. We consider the Igarape Bahia mineralization as being related to the genesis of iron-oxide class deposit, like the Olympic Dam type. Ferropyrosmalite occurs in two different contexts: associated with carbonate veins; associated with heterolithic breccias, composed by BIF and mafic metavolcanic fragments immersed in a magnetic, chalcopyrite, bornite, pyrite, carbonates (calcite to siderite), uranium and REE minerals, and gold, - rich matrix. The growth of ferropyrosmalite is probably due to the substitution of iron rich minerals (chloride, magnetite and siderite), controlled by magmatic fluid influx rich in chlorine. The permeability of breccias and the discontinuity of veins favour fluid percolation. The mode of occurrence of ferropyrosmalite and its relation with amphibole (ferro-hornblende-actinolite) indicate metasomatic growth of the former under temperatures in the transition of greenschist/amphibolite facies. The ferropyrosmalite of the Igarape Bahia deposit represents an uncommon type of occurrence linked to hydrothermal/magmatic conditions. (author)

  1. Mineral weathering experiments to explore the effects of vegetation shifts in high mountain region (Wind River Range, Wyoming, USA)

    Science.gov (United States)

    Mavris, Christian; Furrer, Gerhard; Dahms, Dennis; Anderson, Suzanne P.; Blum, Alex; Goetze, Jens; Wells, Aaron; Egli, Markus

    2015-04-01

    Climate change influences the evolution of soil and landscape. With changing climate, both flora and fauna must adapt to new conditions. It is unknown in many respects to what extent soils will react to warming and vegetation change. The aim of this study was to identify possible consequences for soils in a dry-alpine region with respect to weathering of primary minerals and leaching of elements under expected warming climate conditions due to shifts in vegetation. To achieve this, a field empirical approach was used in combination with laboratory weathering experiments simulating several scenarios. Study sites located in Sinks Canyon and in Stough Basin of the Wind River Range, Wyoming, USA, encompass ecotones that consist of tundra, forest, or sagebrush (from moist to dry, with increasing temperature, respectively). All soils are developed on granitoid moraines. The mineralogy of the soils along the altitudinal sequence was analysed using cathodoluminescence and X-ray diffraction, and revealed clear mineral transformations: biotite and plagioclase were both weathered to smectite while plagioclase also weathered to kaolinite. Cooler, wetter, altitude-dependent conditions seemed to promote weathering of these primary minerals. To test the impact of soil solutions from different ecotones on mineral weathering, aqueous extracts from topsoils (A horizons) were reacted with subsoils (B horizons) in batch experiments. Aqueous extracts of topsoil samples were generated for all three ecotones, and these solutions were characterized. For the batch experiments, the topsoil extracts were reacted for 1800 hours with the subsoil samples of the same ecotone, or with the subsoil samples from higher altitude ecotones. Solutions collected periodically during the experiments were measured using ICP-OES and ion chromatography. Dissolved Ca, Mg and K were mainly controlled by the chemical weathering of oligoclase, K-feldspar and biotite. With increasing altitude (and consequently

  2. International conference Caspy-95. Caspian region: economy, ecology, mineral resources. Technical abstracts

    Energy Technology Data Exchange (ETDEWEB)

    Anon,

    1996-12-31

    The collection of technical abstracts submitted to the International conference Caspy-95 held in Moscow (the Russian Federation), June 20-23, 1995, contains 166 presentations in the following fields: (1) Sea levels`s fluctuation and changes of water balance; (2) Geodynamics of the Caspian region; (3) Prospecting, exploration and exploitation of oil and gas fields; (4) Ecological and environmental problems; (5) Complex monitoring and engineering coastal protection; (6) Social-economical and legal aspects of natural resources usage.

  3. International conference Caspy-95. Caspian region: economy, ecology, mineral resources. Technical abstracts

    International Nuclear Information System (INIS)

    Anon.

    1995-01-01

    The collection of technical abstracts submitted to the International conference Caspy-95 held in Moscow (the Russian Federation), June 20-23, 1995, contains 166 presentations in the following fields: 1) Sea levels's fluctuation and changes of water balance; 2) Geodynamics of the Caspian region; 3) Prospecting, exploration and exploitation of oil and gas fields; 4) Ecological and environmental problems; 5) Complex monitoring and engineering coastal protection; 6) Social-economical and legal aspects of natural resources usage

  4. Estimating the impact of mineral aerosols on crop yields in food insecure regions using statistical crop models

    Science.gov (United States)

    Hoffman, A.; Forest, C. E.; Kemanian, A.

    2016-12-01

    A significant number of food-insecure nations exist in regions of the world where dust plays a large role in the climate system. While the impacts of common climate variables (e.g. temperature, precipitation, ozone, and carbon dioxide) on crop yields are relatively well understood, the impact of mineral aerosols on yields have not yet been thoroughly investigated. This research aims to develop the data and tools to progress our understanding of mineral aerosol impacts on crop yields. Suspended dust affects crop yields by altering the amount and type of radiation reaching the plant, modifying local temperature and precipitation. While dust events (i.e. dust storms) affect crop yields by depleting the soil of nutrients or by defoliation via particle abrasion. The impact of dust on yields is modeled statistically because we are uncertain which impacts will dominate the response on national and regional scales considered in this study. Multiple linear regression is used in a number of large-scale statistical crop modeling studies to estimate yield responses to various climate variables. In alignment with previous work, we develop linear crop models, but build upon this simple method of regression with machine-learning techniques (e.g. random forests) to identify important statistical predictors and isolate how dust affects yields on the scales of interest. To perform this analysis, we develop a crop-climate dataset for maize, soybean, groundnut, sorghum, rice, and wheat for the regions of West Africa, East Africa, South Africa, and the Sahel. Random forest regression models consistently model historic crop yields better than the linear models. In several instances, the random forest models accurately capture the temperature and precipitation threshold behavior in crops. Additionally, improving agricultural technology has caused a well-documented positive trend that dominates time series of global and regional yields. This trend is often removed before regression with

  5. Determination of 226 Ra and 228 Ra in mineral spring waters of the Aguas da Prata region

    International Nuclear Information System (INIS)

    Oliveira, J. de.

    1993-01-01

    Concentration levels of 226 Ra and 228 Ra have been analysed in most of the mineral spring waters available in the Aguas da Prata region. The 226 Ra and 228 Ra were determined by coprecipitation with barium sulphate. The 226 Ra was determined by gross alpha counting of the Ba(Ra)SO 4 precipitate. The determination of 228 Ra was done by measuring the gross beta activity of the same precipitate. Both measurements were carried out in a low background gas flow proportional counter. Dose calculations were performed in order to evaluate the relative importance of such radionuclides to the radiation exposure due to the ingestion of these waters. Based upon measured concentrations, committed effective doses up to 5.5 x 10 -1 mSv/y and 1.0 x 10 -2 mSv/y were observed for 226 Ra and 228 Ra, respectively. These results show that 226 Ra is the main contributor to radiation exposure. (author)

  6. Regional measurement of ventilation and perfusion to detect subtle lung abnormalities in coal miners

    International Nuclear Information System (INIS)

    Susskind, H.; Liu, J.; Brill, A.B.

    1986-01-01

    The relationship between regional pulmonary ventilation (V) and perfusion (Q) uniquely determines the amount of gas exchange that occurs in the lungs. Therefore, the pixel-by-pixel distributions of V and Q were measured with continuously inhaled Kr-81m and i.v. injected Tc-99m MAA, respectively, in a group of 71 subjects exposed to coal dust and then compared with those from a control group of 9 healthy volunteers. Each subject sat upright with his back against a large-field-of-view scintillation camera; 500,000 count images were obtained, analyzed by computer, and then displayed in a 64 x 64 matrix. Individual pixel values of V and Q were correlated by a best-fit regression line, whose slope was proportional to the overall V/Q ratio. The slopes of individual groups of nonsmokers, ex-smokers, and smokers (0.83-0.85) were significantly greater (p < 0.02) than the slope of the controls (0.70 +/- 0.07). In addition, the authors found that the skewness of plots of frequency distribution of V/Q and of V and Q vs V/Q for the individual patient groups was statistically different from that of the normals (p < 0.01). Statistical analysis of local and Q values therefore appears to be a potentially useful, non-invasive method to evaluate subtle regional lung impairment

  7. CARETS: A prototype regional environmental information system. Volume 9: Shore zone land use and land cover; Central Atlantic Regional Ecological Test Site

    Science.gov (United States)

    Alexander, R. H. (Principal Investigator); Dolan, R.; Hayden, B. P.; Vincent, C. L.

    1975-01-01

    The author has identified the following significant results. Analysis of the land use and land cover maps provides a stratification of the CARETS shore area into regions which have a similar environmental organization. Different elements of the landscape are altered less frequently moving inland. Near the beach, higher frequency of monitoring is needed than is needed in the inland areas, including the marsh and estuarine areas.

  8. Differences in regional adiposity, bone mineral density, and physical exercise participation based on exercise self-efficacy among senior adults.

    Science.gov (United States)

    Glenn, J M; Gray, M; Vincenzo, J L

    2015-10-01

    The impact of exercise self-efficacy levels (ESE) on exercise participation, levels of body fat (BF), and bone mineral density (BMD) are unclear in senior-aged adults. The purpose of this study was to investigate effects of ESE on exercise participation, regional distribution of BF, and BMD among seniors. Senior adults (N.=76; 36 males, 40 females) were separated into tertiles (T1, age=60.4±1.4; T2, age=61.3±1.4; T3, age=60.4±1.5) based on self-reported levels of ESE. BMD and regional BF were measured using dual-energy x-ray absorptiometry and exercise participation levels were measured using the Rapid Physical-Activity Questionnaire. MANOVA revealed a significant Wilks Lambda (p exercise participation levels, android BF, gynoid BF, and spinal BMD. ANOVA revealed T3 was significantly lower for android BF (p=0.002) than T1 and T2 (30% and 26%, respectively) while gynoid BF was significantly lower (p=0.012) for T3 (24%) compared to T1. When evaluating exercise participation levels, T3 was significantly higher (p < 0.001) than T1 or T2. Spinal BMD was significantly higher (p=0.030) between T2 (10%) and T1. ESE is an important factor in senior adults ability to maintain longitudinal health.

  9. A Prototype Regional GSI-based EnKF-Variational Hybrid Data Assimilation System for the Rapid Refresh Forecasting System: Dual-Resolution Implementation and Testing Results

    Science.gov (United States)

    Pan, Yujie; Xue, Ming; Zhu, Kefeng; Wang, Mingjun

    2018-05-01

    A dual-resolution (DR) version of a regional ensemble Kalman filter (EnKF)-3D ensemble variational (3DEnVar) coupled hybrid data assimilation system is implemented as a prototype for the operational Rapid Refresh forecasting system. The DR 3DEnVar system combines a high-resolution (HR) deterministic background forecast with lower-resolution (LR) EnKF ensemble perturbations used for flow-dependent background error covariance to produce a HR analysis. The computational cost is substantially reduced by running the ensemble forecasts and EnKF analyses at LR. The DR 3DEnVar system is tested with 3-h cycles over a 9-day period using a 40/˜13-km grid spacing combination. The HR forecasts from the DR hybrid analyses are compared with forecasts launched from HR Gridpoint Statistical Interpolation (GSI) 3D variational (3DVar) analyses, and single LR hybrid analyses interpolated to the HR grid. With the DR 3DEnVar system, a 90% weight for the ensemble covariance yields the lowest forecast errors and the DR hybrid system clearly outperforms the HR GSI 3DVar. Humidity and wind forecasts are also better than those launched from interpolated LR hybrid analyses, but the temperature forecasts are slightly worse. The humidity forecasts are improved most. For precipitation forecasts, the DR 3DEnVar always outperforms HR GSI 3DVar. It also outperforms the LR 3DEnVar, except for the initial forecast period and lower thresholds.

  10. Application of Remote-Sensing Observations for Detecting Patterns of Localization of Cu-Ni Mineralization of the Norilsk Ore Region

    Science.gov (United States)

    Milovsky, G. A.; Ishmukhametova, V. T.; Shemyakina, E. M.

    2017-12-01

    The methods of a complex analysis of materials of space, gravimetric, and magnetometric surveys were developed on the basis of a study of reference fields of the Norilsk ore region (Imangda, etc.) for detection patterns of the localization of Cu-Ni (with PGMs) mineralization in intrusive complexes of the northwestern frame of the Siberian Platform.

  11. Application of sub-regional analysis to bone mineral density of the lower limb from whole body DXA scans

    International Nuclear Information System (INIS)

    Haddaway, Michael J; Davie, Michael W J; Davies, Helen L; Sharp, Christopher A

    2013-01-01

    Bone mineral density at spine and hip is widely used to diagnose osteoporosis. Certain conditions cause changes in bone density at other sites, particularly in the lower limb, with fractures occurring in non-classical locations. Bone density changes at these sites would be of interest for diagnosis and treatment. We describe an application, based on an existing software option for Hologic scanners, which allows reproducible measurement of bone density at six lower limb sites (upper femur, mid-femur, lower femur; upper leg, mid-leg, lower leg). In 30 unselected subjects, referred for bone density, precision (CV%) measured on 2 occasions, separated by repositioning, ranged from 1.7% (mid-femur) to 4.5% at the lowest leg site. Intra-operator precision, measured by three operators on ten subjects on three occasions, was between 1.0% and 2.9%, whilst inter-operator precision was between 1.0% and 3.6%, according to region. These values compare well with those at the spine and upper femur, and in the literature. There was no evidence that this operator agreement improved between occasions 1 and 3. This technique promises to be useful for assessing bone changes at vulnerable sites in the lower limb, in diverse pathological states and in assessing response to treatment. (paper)

  12. Minerals Yearbook, volume I, Metals and Minerals

    Science.gov (United States)

    ,

    2018-01-01

    The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

  13. [Soil organic carbon mineralization of Black Locust forest in the deep soil layer of the hilly region of the Loess Plateau, China].

    Science.gov (United States)

    Ma, Xin-Xin; Xu, Ming-Xiang; Yang, Kai

    2012-11-01

    The deep soil layer (below 100 cm) stores considerable soil organic carbon (SOC). We can reveal its stability and provide the basis for certification of the deep soil carbon sinks by studying the SOC mineralization in the deep soil layer. With the shallow soil layer (0-100 cm) as control, the SOC mineralization under the condition (temperature 15 degrees C, the soil water content 8%) of Black Locust forest in the deep soil layer (100-400 cm) of the hilly region of the Loess Plateau was studied. The results showed that: (1) There was a downward trend in the total SOC mineralization with the increase of soil depth. The total SOC mineralization in the sub-deep soil (100-200 cm) and deep soil (200-400 cm) were equivalent to approximately 88.1% and 67.8% of that in the shallow layer (0-100 cm). (2) Throughout the carbon mineralization process, the same as the shallow soil, the sub-deep and deep soil can be divided into 3 stages. In the rapid decomposition phase, the ratio of the mineralization or organic carbon to the total mineralization in the sub-deep and deep layer (0-10 d) was approximately 50% of that in the shallow layer (0-17 d). In the slow decomposition phase, the ratio of organic carbon mineralization to total mineralization in the sub-deep, deep layer (11-45 d) was 150% of that in the shallow layer (18-45 d). There was no significant difference in this ratio among these three layers (46-62 d) in the relatively stable stage. (3) There was no significant difference (P > 0.05) in the mineralization rate of SOC among the shallow, sub-deep, deep layers. The stability of SOC in the deep soil layer (100-400 cm) was similar to that in the shallow soil layer and the SOC in the deep soil layer was also involved in the global carbon cycle. The change of SOC in the deep soil layer should be taken into account when estimating the effects of soil carbon sequestration in the Hilly Region of the Loess Plateau, China.

  14. Estimating chemical composition of atmospheric deposition fluxes from mineral insoluble particles deposition collected in the western Mediterranean region

    Directory of Open Access Journals (Sweden)

    Y. Fu

    2017-11-01

    Full Text Available In order to measure the mass flux of atmospheric insoluble deposition and to constrain regional models of dust simulation, a network of automatic deposition collectors (CARAGA has been installed throughout the western Mediterranean Basin. Weekly samples of the insoluble fraction of total atmospheric deposition were collected concurrently on filters at five sites including four on western Mediterranean islands (Frioul and Corsica, France; Mallorca, Spain; and Lampedusa, Italy and one in the southern French Alps (Le Casset, and a weighing and ignition protocol was applied in order to quantify their mineral fraction. Atmospheric deposition is both a strong source of nutrients and metals for marine ecosystems in this area. However, there are few data on trace-metal deposition in the literature, since their deposition measurement is difficult to perform. In order to obtain more information from CARAGA atmospheric deposition samples, this study aimed to test their relevance in estimating elemental fluxes in addition to total mass fluxes. The elemental chemical analysis of ashed CARAGA filter samples was based on an acid digestion and an elemental analysis by inductively coupled plasma atomic emission spectroscopy (ICP-AES and mass spectrometry (MS in a clean room. The sampling and analytical protocols were tested to determine the elemental composition for mineral dust tracers (Al, Ca, K, Mg and Ti, nutrients (P and Fe and trace metals (Cd, Co, Cr, Cu, Mn, Ni, V and Zn from simulated wet deposition of dust analogues and traffic soot. The relative mass loss by dissolution in wet deposition was lower than 1 % for Al and Fe, and reached 13 % for P due to its larger solubility in water. For trace metals, this loss represented less than 3 % of the total mass concentration, except for Zn, Cu and Mn for which it could reach 10 %, especially in traffic soot. The chemical contamination during analysis was negligible for all the elements except for Cd

  15. Evaluation of a regional mineral dust model over Northern Africa, Southern Europe and Middle East with AERONET data

    Science.gov (United States)

    Basart, S.; Pérez, C.; Cuevas, E.; Baldasano, J. M.

    2009-04-01

    the model to reproduce AOD (at 550nm) associated to mineral dust 24, 48 and 72h ahead. A suit of discrete statistics as Mean Normalized Bias Error (MNBE), Mean Normalized Gross Error (MNGE) and Root Mean Square Error (RMSE) has been used in order to evaluate the model behaviour. Categorical statistics or skill scores, as model accuracy, bias, probability of detection, false alarm rate and critical success index have been implemented to test the capability of the model to simulate AOD exceeding thresholds defined by the quartiles of each AERONET site. A previous aerosol characterization of AERONET data has been performed for our study region in order to discriminate desert dust contributions (Basart et al., 2008). The first results of the comparison reveal that the modelled dust field agrees in general reasonably well with sun photometer data. Since dust long-range transport is mainly driven by smaller dust particles, the results of this new 8-bins version (with increased number of dust size bins) is considerably better, since the small particle size range (<10µm effective radius) is well described. The best scores are found in North Africa and Middle East. In the Sahel region, an important sub-estimation is observed in wintertime, when the Atlantic outflow transport is important. This is partially due to the more complex processes associated to dust generation in this region (Warren et al., 2007), not well parameterized in dust models yet. Other causes, such as the correct simulation of regional winds or the threshold friction velocity are under research. Moreover, the interaction of mineral dust and biomass burning aerosols from Savannah fires is at its maximum over the region in this season. In southern Europe, the relative errors are higher than in the rest of our study domain mainly due to the presence of different types of aerosols (such as fine pollution aerosols) which appear well-mixed with desert dust. References: Basart, S., C. Pérez, E. Cuevas and J

  16. Regional geochemical maps of the Tonopah 1 degree by 2 degrees Quadrangle, Nevada, based on samples of stream sediment and nonmagnetic heavy-mineral concentrate

    Science.gov (United States)

    Nash, J.T.; Siems, D.F.

    1988-01-01

    This report is part of a series of geologic, geochemical, and geophysical maps of the Tonopah 1° x 2° quadrangle, Nevada, prepared during studies of the area for the Conterminous United States Mineral Assessment Program (CUSMAP). Included here are 21 maps showing the distributions of selected elements or combinations of elements. These regional geochemical maps are based on chemical analyses of the minus-60 mesh (0.25 mm) fraction of stream-sediment samples and the nonmagnetic heavy-mineral concentrate derived from stream sediment. Stream sediments were collected at 1,217 sites. Our geochemical studies of mineralized rock samples provide a framework for evaluating the results from stream sediments.

  17. Developing the lithotectonic framework and model for sulphide mineralization in the Jebilet Massif, Morocco: implications for regional exploration

    OpenAIRE

    Lusty, Paul A.J.; Goodenough, Kathryn M.; Essaifi, Abderrahim; Maacha, Lhou

    2015-01-01

    The central Jebilet massif, part of the North African Variscan Belt, hosts significant polymetallic sulphide mineralization. It is generally considered syngenetic and has many features of volcanogenic massive sulphide (VMS) mineralization. However, some characteristics are not compatible with a classic VMS model and two alternative scenarios for formation have been proposed. Our preliminary research favours a complex, multi-stage development of the sulphide deposits...

  18. Reliability of using DXA around RTHAs. Bone Mineral Density of the femoral neck in resurfacing hip arthroplasty. Precision biased by region of interest and rotation of the hip

    DEFF Research Database (Denmark)

    Penny, Jeannette Østergaard; Varmarken, Jens-Erik; Ovesen, Ole

    2009-01-01

      Introduction:  Resurfacing Total Hip Arthroplasty (RTHA) may preserve the femoral neck bone-stock post-operatively. Bone Mineral Density (BMD), could theoretically be affected by the hip-position, and bias longitudinal studies. We aimed to investigate BMD precision dependency on type of ROI...... the hip was rotated in increments of 15° and 30°, the mean CVs rose to 7.2%, 7.3% and 11.8%.  Rotation affected the precision most in the model that divided the neck in 6 sub regions, predominantly in the lateral and distal regions. For larger-region models, some rotation could be allowed without...

  19. The occurrence and origin of celestite in the Abolfares region, Iran: Implications for Sr-mineralization in Zagros fold belt (ZFB)

    Science.gov (United States)

    Pourkaseb, Houshang; Zarasvandi, Alireza; Rezaei, Mohsen; Mahdavi, Reyhaneh; Ghanavati, Fatemeh

    2017-10-01

    The major celestite deposits in Zagros Fold belt are associated with coastal marine carbonate and evaporate sediments of Oligo-Miocene Asmari and Lower Miocene Ghachsaran Formations. In the Abolfares region, celestite mineralization is extended in the western limb of Bangestan anticline in the carbonates of Early Miocene (middle part of Asmari Formation), underlying by dolomitic carbonates of Burdigalian. From bottom to top three main types of mineralization can be distinguished in the study area: (1) layer texture resulting from replacement of algal limestone by celestite minerals with some parts showing idiomorphic crystals (geodes) along the walls of the cavities, (2) celestite occurrence as irregular massive shape interconnected small crystals and nodules, and (3) celestite mineralization associated with steeply dipping veins and open space fracture fillings, resulting from late-stage epigenetic processes. Highlightly, the ore-hosting carbonate rocks were deposited in an intertidal - supratidal protected setting with hypersaline conditions, in accordance with other celestite deposits of the Zagros Fold belt. The abundance of diagenetic crystallization rhythmites, carbonate and anhydrite inclusions as confirmed by Laser Raman spectroscopy analysis, high Sr/Ba values (average; 8726.1) and strong negative correlations between SO3 vs CaO (R2 = 0.98), SrO vs CaO (R2 = 0.96) with positive correlations between Ba vs SrO (R2 = 0.54) and SO3 vs SrO (R2 = 0.98) highlight the role of high Sr late-diagenetic brines in replacement of carbonates with celestite minerals. It seems that the inception of compressional folding during or soon after the deposition of the Asmari Formation in the carbonate platform at the margin of NW-trending basin in the foreland of the Zagros orogenic belt lead to the upward refluxing of penetrated high-Sr diagenetic brines and celestite mineralization.

  20. Faces prototípicas provenientes de amostras populacionais de uma região brasileira Prototypical faces from samples of the population of a Brazilian region

    Directory of Open Access Journals (Sweden)

    Ana Irene Fonseca Mendes

    2009-01-01

    Full Text Available O objetivo dessa pesquisa foi gerar, por meio de técnica de computação gráfica denominada morphing, faces prototípicas masculinas e femininas a partir de amostras de pessoas que se autodeclaram brancas, pardas e pretas na região de Ribeirão Preto (SP. A cada face prototípica foram utilizadas 64 imagens de faces de voluntários. As faces prototípicas e as faces que as compuseram tiveram a tipicidade de sua cor ou raça julgada por terceiros. Os julgamentos indicaram uma concordância entre a cor/raça-autodeclarada e a heteroatribuída o que indica que os protótipos são representativos de suas respectivas categorias de cor/raça. Discute-se como as faces prototípicas podem ser empregadas em pesquisas básicas e aplicadas em percepção e reconhecimento de faces.The goal of this study was to generate male and female prototypical faces, by morphing technique, from faces of people who were self-declared as white, "mixed race" and black in Ribeirão Preto-SP. Each prototypical face was generated from 64 face images of volunteers. Another sample of volunteers judged the typicality of color/race of the prototypical faces and the faces that composed them. The results suggested a concordance between the self-declared color/race and the judgments, indicating that the prototypical faces are representative of their respective categories of color/race. Applications of the prototypical faces in studies of face perception and face recognition were discussed.

  1. Optical and microphysical properties of natural mineral dust and anthropogenic soil dust near dust source regions over northwestern China

    Science.gov (United States)

    Wang, Xin; Wen, Hui; Shi, Jinsen; Bi, Jianrong; Huang, Zhongwei; Zhang, Beidou; Zhou, Tian; Fu, Kaiqi; Chen, Quanliang; Xin, Jinyuan

    2018-02-01

    Mineral dust aerosols (MDs) not only influence the climate by scattering and absorbing solar radiation but also modify cloud properties and change the ecosystem. From 3 April to 16 May 2014, a ground-based mobile laboratory was deployed to measure the optical and microphysical properties of MDs near dust source regions in Wuwei, Zhangye, and Dunhuang (in chronological order) along the Hexi Corridor over northwestern China. Throughout this dust campaign, the hourly averaged (±standard deviation) aerosol scattering coefficients (σsp, 550 nm) of the particulates with aerodynamic diameters less than 2.5 µm (PM2.5) at these three sites were sequentially 101.5 ± 36.8, 182.2 ± 433.1, and 54.0 ± 32.0 Mm-1. Correspondingly, the absorption coefficients (σap, 637 nm) were 9.7 ± 6.1, 6.0 ± 4.6, and 2.3 ± 0.9 Mm-1; single-scattering albedos (ω, 637 nm) were 0.902 ± 0.025, 0.931 ± 0.037, and 0.949 ± 0.020; and scattering Ångström exponents (Åsp, 450-700 nm) of PM2.5 were 1.28 ± 0.27, 0.77 ± 0.51, and 0.52 ± 0.31. During a severe dust storm in Zhangye (i.e., from 23 to 25 April), the highest values of σsp2.5 ( ˜ 5074 Mm-1), backscattering coefficient (σbsp2.5, ˜ 522 Mm-1), and ω637 ( ˜ 0.993) and the lowest values of backscattering fraction (b2.5, ˜ 0.101) at 550 nm and Åsp2.5 ( ˜ -0.046) at 450-700 nm, with peak values of aerosol number size distribution (appearing at the particle diameter range of 1-3 µm), exhibited that the atmospheric aerosols were dominated by coarse-mode dust aerosols. It is hypothesized that the relatively higher values of mass scattering efficiency during floating dust episodes in Wuwei and Zhangye are attributed to the anthropogenic soil dust produced by agricultural cultivations.

  2. The origin and relation among hot and cold CO{sub 2}-rich mineral waters in Vilarelho da Raia - Pedras Salgadas region, northern Portugal: A geochemical approach

    Energy Technology Data Exchange (ETDEWEB)

    Marques, J.M.; Aires-Barros, L.; Graca, R.C. [Technical Univ. of Lisbon, Lisboa (Portugal)

    1996-12-31

    Coupled isotopic and chemical studies, carried out on hot and cold CO{sub 2}-rich mineral waters discharging in Vilarelho da Raia - Pedras Salgadas region (northern Portugal), have been adopted to purpose some hypothesis on the origin and path-ways of fluids emerging along one of the major regional NNE-trending faults (the so called {open_quotes}Chaves Depression{close_quotes}). Chemical and isotopic ({delta}{sup 18}O and {delta}D) composition of Vilarelho da. Raia cold waters indicate that these waters could be traced as a ramification of the Chaves thermal waters. The enrichment in {sup 18}O and D content in Vidago and Pedras Salgadas cold waters could be attributed either to different recharge altitudes or mixing between deep regional waters with more recent waters derived from local infiltration, in accordance with {sup 3}H activity. Geothermometric interpretation indicates that hot and cold mineral waters have had deep circulation. Model calculations to estimate circulation depth of the groundwater flow system are also indicate deep (about 4km) circulation. Regarding the origin of CO{sub 2} in the thermal and cold mineral waters, two hypothesis could be considered: deep-seated (mantle degassing) or rock (graphitic slates) leaching.

  3. Characterization of Italian honeys (Marche Region on the basis of their mineral content and some typical quality parameters

    Directory of Open Access Journals (Sweden)

    Cucina Domenico

    2007-06-01

    Full Text Available Abstract Background The characterization of three types of Marche (Italy honeys (Acacia, Multifloral, Honeydew was carried out on the basis of the their quality parameters (pH, sugar content, humidity and mineral content (Na, K, Ca, Mg, Cu, Fe, and Mn. Pattern recognition methods such as principal components analysis (PCA and linear discriminant analysis (LDA were performed in order to classify honey samples whose botanical origins were different, and identify the most discriminant parameters. Lastly, using ANOVA and correlations for all parameters, significant differences between diverse types of honey were examined. Results Most of the samples' water content showed good maturity (98% whilst pH values were in the range 3.50 – 4.21 confirming the good quality of the honeys analysed. Potassium was quantitatively the most relevant mineral (mean = 643 ppm, accounting for 79% of the total mineral content. The Ca, Na and Mg contents account for 14, 3 and 3% of the total mineral content respectively, while other minerals (Cu, Mn, Fe were present at very low levels. PCA explained 75% or more of the variance with the first two PC variables. The variables with higher discrimination power according to the multivariate statistical procedure were Mg and pH. On the other hand, all samples of acacia and honeydew, and more than 90% of samples of multifloral type have been correctly classified using the LDA. ANOVA shows significant differences between diverse floral origins for all variables except sugar, moisture and Fe. Conclusion In general, the analytical results obtained for the Marche honeys indicate the products' high quality. The determination of physicochemical parameters and mineral content in combination with modern statistical techniques can be a useful tool for honey classification.

  4. Workplace monitoring and occupational health studies at the Centre for Production of Phosphorus Mineral Fertilizers, Voskresensk (Moscow region, Russia), using nuclear and related analytical techniques

    International Nuclear Information System (INIS)

    Frontasyeva, M.V.; Gundorina, S.F.; Oprea, C.D.; Golubchikov, V.V.; Gorbunov, A.V.; Lyapunov, S.M.; Okina, O.I.; Onischenko, T.L.

    2000-01-01

    The results on monitoring the workplaces of the ''Mineral Fertilizers'' plant in Voskresensk (Moscow Region), one of the largest centres for production of phosphorus mineral fertilizers in Russia, are reported. Assessment of the present-day environmental situation for the main industrial premises of the plant is given. The most typical associations of element-pollutants in the shops of the plant were determined by means of instrumental neutron activation analysis (INAA), atomic absorption spectroscopy (AAS) and energy dispersive X-ray fluorescence spectroscopy (XRFA). The maximal pollution by dust particulates and the highest concentrations for Na, Ca, Sc, Cr, Fe, As, Sb, Sr, rare earth elements (REE), and Th at the loading-unloading sites of the shops were revealed The total dust impact on biosubstrates of the occupational staff (hair, urine) was examined The level of trace element concentrations in the biosubstrates reflects the sustained and systematic impact of air pollutants in the working area of the plant. The results on assessing the present-day environmental situation in the vicinity of the ''Mineral Fertilizers'' plant are given. It is shown that F, Sr and REE produce the most intensive impact on the occupational staff and local residents. The effect of agricultural use of mineral fertilizers byproducts - compost and phosphogypsum - on trace elements in soils and vegetation was examined. (author)

  5. The role of conflict minerals, artisanal mining, and informal trading networks in African intrastate and regional conflicts

    Science.gov (United States)

    Chirico, Peter G.; Malpeli, Katherine C.

    2014-01-01

    The relationship between natural resources and armed conflict gained public and political attention in the 1990s, when it became evident that the mining and trading of diamonds were connected with brutal rebellions in several African nations. Easily extracted resources such as alluvial diamonds and gold have been and continue to be exploited by rebel groups to fund their activities. Artisanal and small-scale miners operating under a quasi-legal status often mine these mineral deposits. While many African countries have legalized artisanal mining and established flow chains through which production is intended to travel, informal trading networks frequently emerge in which miners seek to evade taxes and fees by selling to unauthorized buyers. These networks have the potential to become international in scope, with actors operating in multiple countries. The lack of government control over the artisanal mining sector and the prominence of informal trade networks can have severe social, political, and economic consequences. In the past, mineral extraction fuelled violent civil wars in Sierra Leone, Liberia, and Angola, and it continues to do so today in several other countries. The significant influence of the informal network that surrounds artisanal mining is therefore an important security concern that can extend across borders and have far-reaching impacts.

  6. [Chronic periapical periodontitis of left maxillary first premolar with localized mineralized structure at periapical region: a case report].

    Science.gov (United States)

    Dong, Wei; Li, Ren; Wen, Liming; Qi, Mengchun

    2013-04-01

    Chronic periapical periodontitis is characterized by destruction of periapical tissue and demonstrates translucent feature under X-ray examination. In this article, a localized mineralized structure, which showed high density under X-ray examination, was reported in a patient with chronic periapical periodontitis of left maxillary first premolar. Possible causes of the structure were analyzed and relevant literatures were reviewed.

  7. Rethink! prototyping transdisciplinary concepts of prototyping

    CERN Document Server

    Nagy, Emilia; Stark, Rainer

    2016-01-01

    In this book, the authors describe the findings derived from interaction and cooperation between scientific actors employing diverse practices. They reflect on distinct prototyping concepts and examine the transformation of development culture in their fusion to hybrid approaches and solutions. The products of tomorrow are going to be multifunctional, interactive systems – and already are to some degree today. Collaboration across multiple disciplines is the only way to grasp their complexity in design concepts. This underscores the importance of reconsidering the prototyping process for the development of these systems, particularly in transdisciplinary research teams. “Rethinking Prototyping – new hybrid concepts for prototyping” was a transdisciplinary project that took up this challenge. The aim of this programmatic rethinking was to come up with a general concept of prototyping by combining innovative prototyping concepts, which had been researched and developed in three sub-projects: “Hybrid P...

  8. Architectures of prototypes and architectural prototyping

    DEFF Research Database (Denmark)

    Hansen, Klaus Marius; Christensen, Michael; Sandvad, Elmer

    1998-01-01

    together as a team, but developed a prototype that more than fulfilled the expectations of the shipping company. The prototype should: - complete the first major phase within 10 weeks, - be highly vertical illustrating future work practice, - continuously live up to new requirements from prototyping......This paper reports from experience obtained through development of a prototype of a global customer service system in a project involving a large shipping company and a university research group. The research group had no previous knowledge of the complex business of shipping and had never worked...... sessions with users, - evolve over a long period of time to contain more functionality - allow for 6-7 developers working intensively in parallel. Explicit focus on the software architecture and letting the architecture evolve with the prototype played a major role in resolving these conflicting...

  9. Determination of Seasonal Vitamin and Mineral Contents of Sea Bream (Sparus aurata L., 1758) Cultured in Net Cages in Central Black Sea Region.

    Science.gov (United States)

    Öztürk, Dilara Kaya; Baki, Birol; Karayücel, İsmihan; Öztürk, Recep; Gören, Gülşen Uzun; Karayücel, Sedat

    2018-05-12

    This study aimed to determine the seasonal vitamin and mineral contents of sea bream (Sparus aurata) cultured in net cages in Central Black Sea region. The average seasonal A, D 3 , and E vitamins values in fish meat were between 0.27 ± 0.02-0.60 ± 0.00, 0.98 ± 0.01-1.70 ± 0.00, and 3.10 ± 0.14-6.00 ± 0.21 mg/kg, respectively (p meat were between 276.90 ± 0.99-1788.50 ± 51.27 (p  0.05), 4244.50 ± 8.84-4761.50 ± 1.06 (p  0.05), respectively. As a result, it can be concluded that sea bream cultured in the Central Black Sea region is a rich source of nutrients in terms of vitamins and mineral matters, and fish size, feed quality, and the environmental factors are influential on the contents of vitamin and mineral substances in the fish tissue.

  10. Optical and microphysical properties of natural mineral dust and anthropogenic soil dust near dust source regions over northwestern China

    Directory of Open Access Journals (Sweden)

    X. Wang

    2018-02-01

    Full Text Available Mineral dust aerosols (MDs not only influence the climate by scattering and absorbing solar radiation but also modify cloud properties and change the ecosystem. From 3 April to 16 May 2014, a ground-based mobile laboratory was deployed to measure the optical and microphysical properties of MDs near dust source regions in Wuwei, Zhangye, and Dunhuang (in chronological order along the Hexi Corridor over northwestern China. Throughout this dust campaign, the hourly averaged (±standard deviation aerosol scattering coefficients (σsp, 550 nm of the particulates with aerodynamic diameters less than 2.5 µm (PM2.5 at these three sites were sequentially 101.5 ± 36.8, 182.2 ± 433.1, and 54.0 ± 32.0 Mm−1. Correspondingly, the absorption coefficients (σap, 637 nm were 9.7 ± 6.1, 6.0 ± 4.6, and 2.3 ± 0.9 Mm−1; single-scattering albedos (ω, 637 nm were 0.902 ± 0.025, 0.931 ± 0.037, and 0.949 ± 0.020; and scattering Ångström exponents (Åsp, 450–700 nm of PM2.5 were 1.28 ± 0.27, 0.77 ± 0.51, and 0.52 ± 0.31. During a severe dust storm in Zhangye (i.e., from 23 to 25 April, the highest values of σsp2.5 ( ∼  5074 Mm−1, backscattering coefficient (σbsp2.5,  ∼  522 Mm−1, and ω637 ( ∼  0.993 and the lowest values of backscattering fraction (b2.5,  ∼  0.101 at 550 nm and Åsp2.5 ( ∼  −0.046 at 450–700 nm, with peak values of aerosol number size distribution (appearing at the particle diameter range of 1–3 µm, exhibited that the atmospheric aerosols were dominated by coarse-mode dust aerosols. It is hypothesized that the relatively higher values of mass scattering efficiency during floating dust episodes in Wuwei and Zhangye are attributed to the anthropogenic soil dust produced by agricultural cultivations.

  11. Workplace monitoring and occupational health studies at the centre for production of phosphorus mineral fertilizers, Voskresensk (Moscow Region, Russia), using nuclear and related analytical techniques. Part 1

    International Nuclear Information System (INIS)

    Frontas'eva, M.V.; Oprea, C.D.; Gorbunov, A.V.; Lyapunov, S.M.

    1998-01-01

    This paper contains the preliminary data obtained while monitoring the workplaces of the 'Mineral Fertilizers' plant in Voskresensk (Moscow Region), one of the largest centres for production of phosphorus mineral fertilizers in Russia. The most typical associations of element-pollutants in the shops of the plant were determined by means of XRFA, AAS and NAA. The maximal pollution by dust particulates and the highest concentrations for Na, Ca, Sc, Cr, Fe, As, Sb, Sr, REE, and Th at the loading-unloading sites of the shops were revealed. The level of trace element concentrations in the biosubstrates of the occupational staff (hair, nails, teeth) reflects the sustained and systematic impact of air pollutants in the working area of the plant on its occupational staff. Due to the considerable emissions of fluorine in the technological process, the necessity of assessing the fluorine accumulation in the occupational staff is emphasized

  12. DataCollection Prototyping

    CERN Multimedia

    Beck, H.P.

    DataCollection is a subsystem of the Trigger, DAQ & DCS project responsible for the movement of event data from the ROS to the High Level Triggers. This includes data from Regions of Interest (RoIs) for Level 2, building complete events for the Event Filter and finally transferring accepted events to Mass Storage. It also handles passing the LVL1 RoI pointers and the allocation of Level 2 processors and load balancing of Event Building. During the last 18 months DataCollection has developed a common architecture for the hardware and software required. This involved a radical redesign integrating ideas from separate parts of earlier TDAQ work. An important milestone for this work, now achieved, has been to demonstrate this subsystem in the so-called Phase 2A Integrated Prototype. This prototype comprises the various TDAQ hardware and software components (ROSs, LVL2, etc.) under the control of the TDAQ Online software. The basic functionality has been demonstrated on small testbeds (~8-10 processing nodes)...

  13. Analysis of geological condition of uranium mineralization in the Xiangshan northern uranium orefield in central region of Jiangxi Province

    International Nuclear Information System (INIS)

    Zhou Yulong; Liu Yunlang; Gao Yan

    2013-01-01

    According to the basic conditions of 'source, guide, transportation, storage' for uranium mineralization in strata and different types of geological structure, departure from the condition, the coupling effect of stratigraphy, lithology and structure are studied in the process of uranium mineralization in northern Xiangshan volcanic basin. Studies show that the northern ore field are of good metallogenic geological conditions and the uranium rich ancient land mass and uranium rich magma generated by the melting of deep metamorphic rocks. The main geologic events are volcanic eruptions, accompanied by repeated subvolcanic magma intrusion and strong faults and nappe tectonics which result in volcanic collapse and volcanic ring structures. These ore-forming geological condition control the structural frame for the formation of main uranium deposit type-subvolcanic rocks in northern Xiangshan ore field. (authors)

  14. Potential of heavy minerals in the Valenca-Itacare, Bahia (Brazil) region - Sampling characterization and ore processing

    International Nuclear Information System (INIS)

    Noguti, I.; Feitosa, J.A.

    1989-01-01

    Important heavy minerals deposits were discovered by CBPM in the townships of Nilo Pecanha and Marau, state of Bahia. Ore dressing tests were conducted at CETEC and the results indicate a good potential. Tests were carried out with the Humphreys spiral, with magnetic and electro-static separators were yielding concentrates of ilmenite with 56.0% TiO 2 and Zircon with 65.0% ZrO 2 . (author) [pt

  15. Progress in the study of multivitamins and minerals nutritional supplements for troops stationed in high altitude regions

    OpenAIRE

    Yan-qiang ZHONG; Ying LU

    2013-01-01

    Nutritional supplements are products intended to supplement and improve the diet, and they contain one or more dietary ingredients (including vitamins, minerals herbs or other botanicals, amino acids, protein and other substances) or their constituents. Supplement of vitamins and trace elements play an important role in the nutritional supplements. Supplements play a direct role in health by filling the nutritional gap and preventing diseases caused by nutritional deficiencies, especially for...

  16. Genesis of copper-lead mineralization in the regionally zoned Agnigundala Sulfide Belt, Cuddapah Basin, Andhra Pradesh, India

    Science.gov (United States)

    Bhattacharya, H. N.; Bandyopadhyay, Sandip

    2018-03-01

    Shallow marine sandstone-shale-carbonate sedimentary rocks of the Paleoproterozoic northern Cuddapah basin host copper (Nallakonda deposit), copper-lead (Dhukonda deposit), and lead mineralization (Bandalamottu deposit) which together constitute the Agnigundala Sulfide Belt. The Cu sulfide mineralization in sandstone is both stratabound and disseminated, and Pb sulfide mineralization occurs as stratabound fracture filling veins and/or replacement veins within dolomite. Systematic mineralogical and sulfur, carbon, and oxygen isotope studies of the three deposits indicate a common ore-fluid that deposited copper at Nallakonda, copper-lead at Dhukonda, and lead at Bandalamottu under progressive cooling during migration through sediments. The ore-fluid was of low temperature (water sulfate produced sulfide for ore deposition. It is envisaged that basal red-bed and evaporite-bearing rift-related continental to shallow marine sediments might have acted as the source for the metals. Rift-related faults developed during sedimentation in the basin might have punctured the ore-fluid pool in the lower sedimentary succession and also acted as conduits for their upward migration. The ore-bearing horizons have participated in deformations during basin inversion without any recognizable remobilization.

  17. Regional Tectonic Control of Tertiary Mineralization and Recent Faulting in the Southern Basin-Range Province, an Application of ERTS-1 Data

    Science.gov (United States)

    Bechtold, I. C.; Liggett, M. A.; Childs, J. F.

    1973-01-01

    Research based on ERTS-1 MSS imagery and field work in the southern Basin-Range Province of California, Nevada and Arizona has shown regional tectonic control of volcanism, plutonism, mineralization and faulting. This paper covers an area centered on the Colorado River between 34 15' N and 36 45' N. During the mid-Tertiary, the area was the site of plutonism and genetically related volcanism fed by fissure systems now exposed as dike swarms. Dikes, elongate plutons, and coeval normal faults trend generally northward and are believed to have resulted from east-west crustal extension. In the extensional province, gold silver mineralization is closely related to Tertiary igneous activity. Similarities in ore, structural setting, and rock types define a metallogenic district of high potential for exploration. The ERTS imagery also provides a basis for regional inventory of small faults which cut alluvium. This capability for efficient regional surveys of Recent faulting should be considered in land use planning, geologic hazards study, civil engineering and hydrology.

  18. Determination of Mineral, Trace Element, and Pesticide Levels in Honey Samples Originating from Different Regions of Malaysia Compared to Manuka Honey

    Science.gov (United States)

    Moniruzzaman, Mohammed; Chowdhury, Muhammed Alamgir Zaman; Rahman, Mohammad Abdur; Sulaiman, Siti Amrah; Gan, Siew Hua

    2014-01-01

    The present study was undertaken to determine the content of six minerals, five trace elements, and ten pesticide residues in honeys originating from different regions of Malaysia. Calcium (Ca), magnesium (Mg), iron (Fe), and zinc (Zn) were analyzed by flame atomic absorption spectrometry (FAAS), while sodium (Na) and potassium (K) were analyzed by flame emission spectrometry (FAES). Trace elements such as arsenic (As), lead (Pb), cadmium (Cd), copper (Cu), and cobalt (Co) were analyzed by graphite furnace atomic absorption spectrometry (GFAAS) following the microwave digestion of honey. High mineral contents were observed in the investigated honeys with K, Na, Ca, and Fe being the most abundant elements (mean concentrations of 1349.34, 236.80, 183.67, and 162.31 mg/kg, resp.). The concentrations of the trace elements were within the recommended limits, indicating that the honeys were of good quality. Principal component analysis reveals good discrimination between the different honey samples. The pesticide analysis for the presence of organophosphorus and carbamates was performed by high performance liquid chromatography (HPLC). No pesticide residues were detected in any of the investigated honey samples, indicating that the honeys were pure. Our study reveals that Malaysian honeys are rich sources of minerals with trace elements present within permissible limits and that they are free from pesticide contamination. PMID:24982869

  19. Determination of Mineral, Trace Element, and Pesticide Levels in Honey Samples Originating from Different Regions of Malaysia Compared to Manuka Honey

    Directory of Open Access Journals (Sweden)

    Mohammed Moniruzzaman

    2014-01-01

    Full Text Available The present study was undertaken to determine the content of six minerals, five trace elements, and ten pesticide residues in honeys originating from different regions of Malaysia. Calcium (Ca, magnesium (Mg, iron (Fe, and zinc (Zn were analyzed by flame atomic absorption spectrometry (FAAS, while sodium (Na and potassium (K were analyzed by flame emission spectrometry (FAES. Trace elements such as arsenic (As, lead (Pb, cadmium (Cd, copper (Cu, and cobalt (Co were analyzed by graphite furnace atomic absorption spectrometry (GFAAS following the microwave digestion of honey. High mineral contents were observed in the investigated honeys with K, Na, Ca, and Fe being the most abundant elements (mean concentrations of 1349.34, 236.80, 183.67, and 162.31 mg/kg, resp.. The concentrations of the trace elements were within the recommended limits, indicating that the honeys were of good quality. Principal component analysis reveals good discrimination between the different honey samples. The pesticide analysis for the presence of organophosphorus and carbamates was performed by high performance liquid chromatography (HPLC. No pesticide residues were detected in any of the investigated honey samples, indicating that the honeys were pure. Our study reveals that Malaysian honeys are rich sources of minerals with trace elements present within permissible limits and that they are free from pesticide contamination.

  20. Rb-Sr dating of strain-induced mineral growth in two ductile shear zones in the western gneiss region of Nord-Troendelag, Central Norway

    International Nuclear Information System (INIS)

    Piasecki, M.A.; Cliff, R.A.

    1988-01-01

    In the Bjugn district of the northern part of the Western Gneiss Region, Nord-Troendelag, a basement gneiss-cover nappe boundary is marked by a thick zone of ductile shearing. In this zone a layer-parallel mylonitic fabric with related new mineral growth overprints and retrogresses a previous fabric associated with a granulite facies mineral assemblage. Related minor shear belts contain abundant new minerals and vein systems, including pegmatites, believed to represent strain-induced products formed at the time of the shearing movements. Central parts of two large muscovite books from such a pegmatite yielded Rb-Sr, Early to Middle Devonian ages of 389±6 Ma and 386±6 Ma, interpreted as indicating the approximate time of pegmatite formation and of the shearing. Small, matrix-size muscovite and biotite grains from the host mylonite gave ages of 378±6 Ma and 365±5 Ma, respectively, supposed to relate to post-shearing uplift and cooling

  1. Determination of mineral, trace element, and pesticide levels in honey samples originating from different regions of Malaysia compared to manuka honey.

    Science.gov (United States)

    Moniruzzaman, Mohammed; Chowdhury, Muhammed Alamgir Zaman; Rahman, Mohammad Abdur; Sulaiman, Siti Amrah; Gan, Siew Hua

    2014-01-01

    The present study was undertaken to determine the content of six minerals, five trace elements, and ten pesticide residues in honeys originating from different regions of Malaysia. Calcium (Ca), magnesium (Mg), iron (Fe), and zinc (Zn) were analyzed by flame atomic absorption spectrometry (FAAS), while sodium (Na) and potassium (K) were analyzed by flame emission spectrometry (FAES). Trace elements such as arsenic (As), lead (Pb), cadmium (Cd), copper (Cu), and cobalt (Co) were analyzed by graphite furnace atomic absorption spectrometry (GFAAS) following the microwave digestion of honey. High mineral contents were observed in the investigated honeys with K, Na, Ca, and Fe being the most abundant elements (mean concentrations of 1349.34, 236.80, 183.67, and 162.31 mg/kg, resp.). The concentrations of the trace elements were within the recommended limits, indicating that the honeys were of good quality. Principal component analysis reveals good discrimination between the different honey samples. The pesticide analysis for the presence of organophosphorus and carbamates was performed by high performance liquid chromatography (HPLC). No pesticide residues were detected in any of the investigated honey samples, indicating that the honeys were pure. Our study reveals that Malaysian honeys are rich sources of minerals with trace elements present within permissible limits and that they are free from pesticide contamination.

  2. Workplace monitoring and occupational health studies at the centre for production of phosphorus mineral fertilizers, Voskresensk (Moscow Region, Russia), using nuclear and related analytical techniques. Part 2

    International Nuclear Information System (INIS)

    Frontas'eva, M.V.; Gundorina, S.F.; Oprea, C.D.; Gorbunov, A.V.; Lyapunov, S.M.

    1999-01-01

    The results on further monitoring the workplaces of the 'Mineral Fertilizers' plant in Voskresensk (Moscow Region), one of the largest centres for producing phosphorus mineral fertilizers in Russia, and adjacent to it territories are reported. Snow has been chosen as a depositing media to characterize both aerosol and gaseous components of atmospheric pollution. Data on cation-anion analysis in the snow filtrate are reported. They do not exceed hygienic normatives typical for the industrial and urban areas. The distribution of Sr, Y, Sb, Pb, REE, and Th along the profile: the 'Mineral Fertilizers' plant -- 15 km distance -- was examined through the analysis of snow dust. Trace element concentrations in vegetation and soils allow one to state that F, Sr and REE produce the most intensive impact on the occupational staff. As follows from the results obtained, the most hazardous shop of the plant is that for phosphate oleum extraction (OPE), and the most hazardous professions are workers. The fluorine concentration in their hair exceeds the background ones by a factor of 10-30. The same tendency was observed for teeth of the workers. No definite correlation between the length of service and the level of fluorine content in hair and teeth was observed

  3. Deposits of minerals of the Kirovograd ore region of the Ukrainian shield: connection with the deep process

    OpenAIRE

    Usenko, O.V.

    2017-01-01

    Conditions of magmatic rocks complexes and mineral deposits formation of the central part of the Ingul block are determined by existence of two melting sources in the mantle and the crust as well as by the deep permeable «transform» zone - tectonic suture Kherson-Smolensk. Along the deep transform zone supply of the mantle source by melts and fluids is realized and the existence of the crust source provides mixing of earlier melts with new portions added from the mantle. Changing of compositi...

  4. Characterization of mineral coatings associated with a Pleistocene-Holocene rock art style: The Northern Running Figures of the East Alligator River region, western Arnhem Land, Australia.

    Science.gov (United States)

    King, Penelope L; Troitzsch, Ulrike; Jones, Tristen

    2017-02-01

    This data article contains mineralogic and chemical data from mineral coatings associated with rock art from the East Alligator River region. The coatings were collected adjacent to a rock art style known as the "Northern Running Figures" for the purposes of radiocarbon dating (doi:10.1016/j.jasrep.2016.11.016; (T. Jones, V. Levchenko, P.L. King, U. Troitzsch, D. Wesley, 2017) [1]). This contribution includes raw and processed powder X-ray Diffraction data, Scanning Electron Microscopy energy dispersive spectroscopy data, and Fourier Transform infrared spectral data.

  5. Geology and mineralization of the Jabalat alkali-feldspar granite, northern Asir region, Kingdom of Saudi Arabia

    Science.gov (United States)

    Al Tayyar, Jaffar; Jackson, Norman J.; Al-Yazidi, Saeed

    The Jabalat post-tectonic granite pluton is composed of albite- and oligoclase-bearing, low-calcium, F-, Sn- and Rb-rich subsolvus granites. These granites display evidence of late-magmatic, granitophile- and metallic-element specialization, resulting ultimately in the development of post-magmatic, metalliferous hydrothermal systems characterized by a Mo sbnd Sn sbnd Cu sbnd Pb sbnd Zn sbnd Bi sbnd Ag sbnd F signature. Two main types of mineralization are present within the pluton and its environs: (1) weakly mineralized felsic and aplitic dikes and veins enhanced in Mo, Bi, Ag, Pb and Cu; and (2) pyrite—molybdenite—chalcopyrite-bearing quartz and quartz—feldspar veins rich in Mo, Sn, Bi, Cu, Zn and Ag. A satellite stock, 3 km north of the main intrusion, is composed of fine-grained, miarolitic, muscovite—albite—microcline (microperthite) granite. The flanks of this intrusion and adjacent dioritic rocks are greisenized and highly enriched in Sn, Bi and Ag. Quartz veins which transect the satellite stock contain molybdenite and stannite.

  6. Application of mineral fertilizers in Bulgaria and their efficiency on the slightly leached chernozems of the Dobroudja region

    International Nuclear Information System (INIS)

    Nankova, M.; Kirchev, H.; Penchev, E.

    1999-01-01

    Over the past years the agriculture in Bulgaria is undergoing a process of reconstruction and structural changes. The utilization of mineral fertilizers has gradually increased since 1948 and reached its summit in 1981 when about 227 kg/ha NPK have been used. Nowadays these norms have been were and in 1996 they were only 35 kg/ha at the expense of applying N-fertilizers mainly in wheat. The efficiency of the applied nutrients was estimated on slightly leached chernozem in the period 1967-1997. The regular long term fertilization of N 120 P 60 K 0 had a favorable effect on grain yield in an agronomical and economic aspect (5070 kg/ha). The highest grain yield was received at fertilization with N 120 P 120 K 120 (5230 kg/ha). Refs. 4 (author)

  7. Investigation on the age of mineralization in the Sungun porphyry Cu-Mo deposit, NW Iran with a regional metallogenic perspective

    Science.gov (United States)

    Simmonds, Vartan; Moazzen, Mohssen; Mathur, Ryan

    2016-04-01

    The Sungun porphyry copper deposit (PCD) is located in NW Iran, neighbouring several other PCDs and prospects in the region and the Lesser Caucasus (south Armenia). It lies on the Urumieh-Dokhtar magmatic arc (UDMA), which formed through the northeast-ward subduction of the Neo-Tethyan oceanic crust beneath the Central Iranian plate during late-Mesozoic and early-Cenozoic [1], and hosts the porphyry copper metallogenic belt of Iran. The Sungun PCD is the second largest deposit in Iran with ore reserves of about 850 Mt at 0.62 wt% Cu and 0.01 wt% Mo and probable reserves over 1Gt. The monzonitic to quartz monzonitic porphyry stock intruded the upper Cretaceous carbonates and Eocene volcano-sedimentary rocks. It produced a skarn-type mineralization at its contact zone with the carbonate rocks, as well as vast hydrothermal alteration zones and porphyry-type Cu and Mo mineralization. The zircon U-Pb age of the host porphyry stock is about 22.5±0.4 to 20.1±0.4 Ma [2]. Re-Os dating of four molybdenite separates from this PCD shows ages ranging between 22.9±0.2 to 21.7±0.2 Ma, with an average of 22.57±0.2 Ma, corresponding to the early Miocene (Aquitanian). These ages indicate that both the porphyry stock and the Cu-Mo mineralization are post-collisional events, similar to many other deposits and prospects in NW and central Iran and south Armenia, and the mineralization occurred shortly after the emplacement of the host stock, corresponding better to the ages obtained from the marginal parts of the stock. Magmatism and mineralization in Sungun coincides with the third metallogenic epoch in the Lesser Caucasus (Eocene to Miocene; [3]), though it is considerably younger than all of the dated PCDs and prospects in the south Armenia. It also postdates Cu-Mo mineralizations in the Saheb Divan (35 Ma), Qaradagh batholith (31.22±0.28 to 25.19±0.19 Ma), as well as Haft Cheshmeh PCD (28.18±0.42 to 27.05±0.37 Ma) in NW Iran, while it seems to be coeval with the Kighal

  8. Regional seismic-wave propagation from the M5.8 23 August 2011, Mineral, Virginia, earthquake

    Science.gov (United States)

    Pollitz, Fred; Mooney, Walter D.

    2015-01-01

    The M5.8 23 August 2011 Mineral, Virginia, earthquake was felt over nearly the entire eastern United States and was recorded by a wide array of seismic broadband instruments. The earthquake occurred ~200 km southeast of the boundary between two distinct geologic belts, the Piedmont and Blue Ridge terranes to the southeast and the Valley and Ridge Province to the northwest. At a dominant period of 3 s, coherent postcritical P-wave (i.e., direct longitudinal waves trapped in the crustal waveguide) arrivals persist to a much greater distance for propagation paths toward the northwest quadrant than toward other directions; this is probably related to the relatively high crustal thickness beneath and west of the Appalachian Mountains. The seismic surface-wave arrivals comprise two distinct classes: those with weakly dispersed Rayleigh waves and those with strongly dispersed Rayleigh waves. We attribute the character of Rayleigh wave arrivals in the first class to wave propagation through a predominantly crystalline crust (Blue Ridge Mountains and Piedmont terranes) with a relatively thin veneer of sedimentary rock, whereas the temporal extent of the Rayleigh wave arrivals in the second class are well explained as the effect of the thick sedimentary cover of the Valley and Ridge Province and adjacent Appalachian Plateau province to its northwest. Broadband surface-wave ground velocity is amplified along both north-northwest and northeast azimuths from the Mineral, Virginia, source. The former may arise from lateral focusing effects arising from locally thick sedimentary cover in the Appalachian Basin, and the latter may result from directivity effects due to a northeast rupture propagation along the finite fault plane.

  9. Automated segmentation of knee and ankle regions of rats from CT images to quantify bone mineral density for monitoring treatments of rheumatoid arthritis

    Science.gov (United States)

    Cruz, Francisco; Sevilla, Raquel; Zhu, Joe; Vanko, Amy; Lee, Jung Hoon; Dogdas, Belma; Zhang, Weisheng

    2014-03-01

    Bone mineral density (BMD) obtained from a CT image is an imaging biomarker used pre-clinically for characterizing the Rheumatoid arthritis (RA) phenotype. We use this biomarker in animal studies for evaluating disease progression and for testing various compounds. In the current setting, BMD measurements are obtained manually by selecting the regions of interest from three-dimensional (3-D) CT images of rat legs, which results in a laborious and low-throughput process. Combining image processing techniques, such as intensity thresholding and skeletonization, with mathematical techniques in curve fitting and curvature calculations, we developed an algorithm for quick, consistent, and automatic detection of joints in large CT data sets. The implemented algorithm has reduced analysis time for a study with 200 CT images from 10 days to 3 days and has improved the robust detection of the obtained regions of interest compared with manual segmentation. This algorithm has been used successfully in over 40 studies.

  10. Imagining the prototype

    OpenAIRE

    Brouwer, C. E.; Bhomer, ten, M.; Melkas, H.; Buur, J.

    2013-01-01

    This article reports on the analysis of a design session, employing conversation analysis. In the design session three experts and a designer discuss a prototype of a shirt, which has been developed with the input from these experts. The analysis focuses on the type of involvement of the participants with the prototype and how they explicate the points they make in the discussion with or without making use of the prototype. Three techniques for explicating design issues that exploit the proto...

  11. Rapid Prototyping Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The ARDEC Rapid Prototyping (RP) Laboratory was established in December 1992 to provide low cost RP capabilities to the ARDEC engineering community. The Stratasys,...

  12. Fabrication and Prototyping Lab

    Data.gov (United States)

    Federal Laboratory Consortium — Purpose: The Fabrication and Prototyping Lab for composite structures provides a wide variety of fabrication capabilities critical to enabling hands-on research and...

  13. Transcriptome Analysis of Invasive Plants in Response to Mineral Toxicity of Reclaimed Coal-Mine Soil in the Appalachian Region.

    Science.gov (United States)

    Saminathan, Thangasamy; Malkaram, Sridhar A; Patel, Dharmesh; Taylor, Kaitlyn; Hass, Amir; Nimmakayala, Padma; Huber, David H; Reddy, Umesh K

    2015-09-01

    Efficient postmining reclamation requires successful revegetation. By using RNA sequencing, we evaluated the growth response of two invasive plants, goutweed (Aegopodium podagraria L.) and mugwort (Artemisia vulgaris), grown in two Appalachian acid-mine soils (MS-I and -II, pH ∼ 4.6). Although deficient in macronutrients, both soils contained high levels of plant-available Al, Fe and Mn. Both plant types showed toxicity tolerance, but metal accumulation differed by plant and site. With MS-I, Al accumulation was greater for mugwort than goutweed (385 ± 47 vs 2151 ± 251 μg g-1). Al concentration was similar between mine sites, but its accumulation in mugwort was greater with MS-I than MS-II, with no difference in accumulation by site for goutweed. An in situ approach revealed deregulation of multiple factors such as transporters, transcription factors, and metal chelators for metal uptake or exclusion. The two plant systems showed common gene expression patterns for different pathways. Both plant systems appeared to have few common heavy-metal pathway regulators addressing mineral toxicity/deficiency in both mine sites, which implies adaptability of invasive plants for efficient growth at mine sites with toxic waste. Functional genomics can be used to screen for plant adaptability, especially for reclamation and phytoremediation of contaminated soils and waters.

  14. Designing and testing prototypes

    NARCIS (Netherlands)

    Vereijken, P.; Wijnands, F.; Stol, W.

    1995-01-01

    This second progress report focuses on designing a theoretical prototype by linking parameters to methods and designing the methods in this context until they are ready for initial testing. The report focuses also on testing and improving the prototype in general and the methods in particular until

  15. EUCLID ARCHIVE SYSTEM PROTOTYPE

    NARCIS (Netherlands)

    Belikov, Andrey; Williams, Owen; Droge, Bob; Tsyganov, Andrey; Boxhoorn, Danny; McFarland, John; Verdoes Kleijn, Gijs; Valentijn, E; Altieri, Bruno; Dabin, Christophe; Pasian, F.; Osuna, Pedro; Soille, P.; Marchetti, P.G.

    2014-01-01

    The Euclid Archive System prototype is a functional information system which is used to address the numerous challenges in the development of fully functional data processing system for Euclid. The prototype must support the highly distributed nature of the Euclid Science Ground System, with Science

  16. Specifications in software prototyping

    OpenAIRE

    Luqi; Chang, Carl K.; Zhu, Hong

    1998-01-01

    We explore the use of software speci®cations for software prototyping. This paper describes a process model for software prototyping, and shows how specifications can be used to support such a process via a cellular mobile phone switch example.

  17. EPCiR prototype

    DEFF Research Database (Denmark)

    2003-01-01

    A prototype of a residential pervasive computing platform based on OSGi involving among other a mock-up of an health care bandage.......A prototype of a residential pervasive computing platform based on OSGi involving among other a mock-up of an health care bandage....

  18. Cooperative Prototyping Experiments

    DEFF Research Database (Denmark)

    Bødker, Susanne; Grønbæk, Kaj

    1989-01-01

    This paper describes experiments with a design technique that we denote cooperative prototyping. The experiments consider design of a patient case record system for municipal dental clinics in which we used HyperCard, an off the shelf programming environment for the Macintosh. In the ecperiments we...... tried to achieve a fluent work-like evaluation of prototypes where users envisioned future work with a computer tool, at the same time as we made on-line modifications of prototypes in cooperation with the users when breakdown occur in their work-like evaluation. The experiments showed...... that it was possible to make a number of direct manipulation changes of prototypes in cooperation with the users, in interplay with their fluent work-like evaluation of these. However, breakdown occurred in the prototyping process when we reached the limits of the direct manipulation support for modification. From...

  19. Miners' welfare

    Energy Technology Data Exchange (ETDEWEB)

    Buckley, C

    1984-06-13

    The Miners' Welfare Committee (MWC) was formed in Britain in 1921 and initiated building programmes to provide welfare amenities for miners and families, using architecture to improve the quality of a miner's working and leisure time. The article reviews the MWC's work, and assesses the design and architecture at the Selby Coalfield. (7 refs.)

  20. Impact of the breeding region and the season on the content of the selected mineral elements in the hair of cows

    Directory of Open Access Journals (Sweden)

    Dorota CYGAN-SZCZEGIELNIAK

    2015-12-01

    Full Text Available The aim of the research was to analyze the effect of the season and the breeding region on the content of selected minerals (Ca, Mg, Na and K in the hair of dairy cows. The research material was made up of 114 polish Holstein-Friesians breed cows from three breeding centres in Poland: Kombinat Rolny Sp. z o. o. - Kietrz (the opolskie province, Hodowla Zarodowa Zwierząt Sp. z o.o. - Knyszyn (the podlaskie province and Ośrodek Hodowli Zarodowej Sp. z o.o. - Osięciny (the kujawsko-pomorskie province. The cows were kept in freestanding cowsheds with den boxes. The animal nutrition involved the use of the TMR system, considering the division into nutrition groups. The hair was sampled in summer and in the period of winter and spring from the side of the body, right behind the coastal arch. Determination of Ca, Mg, Na and K was performed by means of atomic absorption spectrophotometry (AAS. The study revealed seasonal variations in the content of mineral elements in the hair of dry cows and a region-dependent differentiation. The highest content of the quantity elements in question was found in the hair of the cows from Osięciny. The mean concentration of Ca, Mg, Na and K in the hair of cows from Osięciny was statistically significantly higher than in the hair collected in winter from the animals from Knyszyn and Kietrz. The lowest values of the determined elements were noted in the hair of cows bred in Knyszyn. The investigation of the correlation between the amounts of the elements, based on an analysis of all samples of hair, revealed a positive correlation between Na and K cations, as well as between Mg and Ca cations.

  1. PRMS Data Warehousing Prototype

    Science.gov (United States)

    Guruvadoo, Eranna K.

    2002-01-01

    Project and Resource Management System (PRMS) is a web-based, mid-level management tool developed at KSC to provide a unified enterprise framework for Project and Mission management. The addition of a data warehouse as a strategic component to the PRMS is investigated through the analysis, design and implementation processes of a data warehouse prototype. As a proof of concept, a demonstration of the prototype with its OLAP's technology for multidimensional data analysis is made. The results of the data analysis and the design constraints are discussed. The prototype can be used to motivate interest and support for an operational data warehouse.

  2. Sociocultural and institutional drivers and constraints to mineral supply; the meaning of scarcity in the 21st century: drivers and constraints to the supply of minerals using regional, national and global perspectives

    Science.gov (United States)

    Brown, William M.

    2002-01-01

    The sociocultural dimensions of mineral supply at the outset of the 21st century are making the supply process increasingly complex. The dimensions encompass legal, financial, environmental, cultural, and global implications of mining, and are driving unprecedented change in the way minerals supply will be accomplished in the future. Minerals scarcity on a global scale is subordinate to other societal issues about mineral resources and reserves estimated to meet society's demands for decades to centuries in the future. This report reviews historical and present-day sociocultural drivers of change, and reactions of the minerals industry to these drivers. It is reflective primarily of conditions in the United States, but also uses examples from other countries. It expresses viewpoints on sociocultural drivers as seen by constituents of the minerals industry and several other communities of interest including Aboriginal peoples, non-government organizations; labor; mining-dependent communities; mining-affected communities; researchers; and government (federal, state/provincial, and local). It provides overviews of the demand for minerals in the United States, and the status of land available for mining. The report uses a case study of a metals mining project in Wisconsin to illustrate specific sociocultural drivers and constraints to minerals supply, and how these influence the minerals industry. Over the past 150 years, a progression of sociocultural movements under the headings of conservationism, environmentalism, and sustainable development have nurtured societal values that have come to influence the mineral supply process in important ways. These movements reflect a continuing tension between the demand for minerals and other resources, and the simultaneous demand for aesthetic, spiritual, ecological, cultural, and other attributes of the land. The tension is an important element in current international debates about the meaning and future of sustainable

  3. Characterization of clay minerals

    International Nuclear Information System (INIS)

    Diaz N, C.; Olguin, M.T.; Solache R, M.; Alarcon H, T.; Aguilar E, A.

    2002-01-01

    The natural clays are the more abundant minerals on the crust. They are used for making diverse industrial products. Due to the adsorption and ion exchange properties of these, a great interest for developing research directed toward the use of natural clays for the waste water treatment has been aroused. As part of such researches it is very important to carry out previously the characterization of the interest materials. In this work the results of the mineral and elemental chemical composition are presented as well as the morphological characteristics of clay minerals from different regions of the Mexican Republic. (Author)

  4. Investigation of Regional Fractures and Cu Mineralization Relationships in the Khezrabad and Shahr-e-Babak Area: Using Fry and Fractal analysis

    Directory of Open Access Journals (Sweden)

    Alireza Zarasvandi

    2015-10-01

    such linear trends occur at a characteristic spacing. There is 37 and 42 copper point's index in the Khezr-Abad and Shar-B-Babak areas. The Fry patterns of copper index for two areas were determined with application of Dot Proc software. Fractal analysis is another technique for determination of regional distribution of faults. In this research the fractal dimension of joints and faults was determined in different locations using box-counting fractal method and drawing the logarithmic graphs. Results - The major faults show NW/SE trends in the Khezr-Abad area. They have a similar trend with Dehshir-Baft fault. Other sets of faults show NE/SW trend. These faults are younger than the Dehshir-Baft and release sinistral sense of shear. - Intrusion of two intrusive bodies leads to the accumulation of strike-slip faults in the vicinity of intrusive rocks. In this region faults and joints mainly show NW/SE and NE/SW trends. - The results of Fry analysis show that the mineralization in the Khezr-Abad occurred in the Cretaceous (and younger rocks with NE/SW and NW/SE orientations. In the other words, these areas of mineralization are mainly related to the secondary faults or (P faults in the pull basins and cross cutting points of these faults which have similar strike with the Dehshir-Baft fault. NE/SW mineralization is probably related to the tensional stress direction or faults having the general trends of central Iran structures. - The calculations of fractal dimension show that the southeastern parts of the Khezr Abad have higher amounts of fractal dimension (Db= 1.7002. Also there is a relatively higher copper index in this part, indicating a logical relation between fault structures and mineralization. -The generated maps indicate that the mineralization in the Shahr-e-Babak area occurred at the intersection of faults and volcanic system and the Fry analysis shows a NE/SW and NW/SE trend of ore concentration. - Northwestern parts of the Share-e-Babak show higher fractal

  5. Workplace monitoring and occupational health studies at the centre for production of phosphorus mineral fertilizers, Voskresensk (Moscow Region, Russia), using nuclear and related analytical techniques

    International Nuclear Information System (INIS)

    Frontasyeva, M.V.; Oprea, C.D.; Gorbunov, A.V.; Lyapunov, S.M.

    1998-01-01

    This report contains the preliminary data obtained while monitoring the workplaces of the 'Mineral Fertilizers' plant in Voskresensk (Moscow Region), one of the largest centres for producing phosphorus mineral fertilizers in Russia. Assessment of the present-day environmental situation for the main industrial premises of the plant is given. The most typical associations of element-pollutants in the shops of the plant were determined by means of XRF, AAS and NAA. The maximal pollution by dust particulates and the highest concentrations for Na, Ca, Sc, Cr, Fe, As, Sb, Sr, REE, and Th at the loading-unloading sites of the sh ops were revealed. Quite notable, but not exceeding the maximum permissible level, content of As was determined on the premises of the Central Laboratory of the plant. The total dust impact on the quality of the drinking water consumed at the plant and on the bio-substrates of the occupational staff (hair, nails) were examined. The level of trace element concentrations in the bio-substrates reflects the sustained and systematic impact of air pollutants in the working area of the plant on its occupational staff. Biochemical association of trace elements accumulated in employee hair fully correlates with the specific element content of the atmospheric aerosols. Data on the trace element content in nails is identical to that in the hair of the examined staff. Preliminary results of the REE distributions in employee teeth differ from those in the aerosol component of the air at the working sites. The same differentiation for REE is characteristic for employee hair, especially for Sm/Eu, obtained by means of radiochemical analysis. Due to the considerable emissions of fluorine in the technological process, the necessity of assessing the fluorine accumulation in the occupational staff is emphasized. (author)

  6. Recent results on prototype aerogel threshold counters for particle identification in the region: 0.5 6 4.3 GeV / c

    International Nuclear Information System (INIS)

    Arisaka, K.; Borsato, E.; DalCorso, F.; Iacovella, F.; Morandin, M.; Posocco, M.; Stroili, R.; Torassa, DE.; Voci, C.; Boutigny, D.; Bonis, I. de; Favier, J.; Karyotakis, Y.; Lafaye, R.; Ferroni, F.; Mazzoni, M.A.; Morganti, S.; Piredda, G.; Santacesaria, R.; Oyang, J.

    1996-01-01

    The recent development of new processes has lead to the fabrication of small density silica aerogel with high optical quality. The BaBar experiment, in order to achieve its physics program, requires a good pion kaon identification capability up to 4.3 GeV/c able to work inside a 1.5 Tesla magnetic field. An aerogel threshold counter using thee combination of 2 refractive indices (1.055 and 1.007) can be used to complete the angular coverage of the particle identification system in the forward region. Different detector geometries read out by two photo-detectors types (fine mesh phototubes and Hybrid Photo-Diodes) have been considered and tested in CERN beam test. (author)

  7. Study of Chinese pollution with the 3D regional chemistry transport CHIMERE model and remote sensing observations, with a focus on mineral dust impacts

    Science.gov (United States)

    Lachatre, Mathieu; Foret, Gilles; Beekmann, Matthias; Cheiney, Audrey; Dufour, Gaëlle; Laurent, Benoit; Cuesta, Juan

    2017-04-01

    Since the end of the 20th century, China has observed important growth in numerous sectors. China's Gross Domestic Product (GDP) has been multiply by 4 during the 2000-2010 decade (National Bureau of Statistics of China), mostly because of the industry's growth. These evolutions have been accompanied by important increases of atmospheric pollutants emissions (Yinmin et al, Atmo Env, 2016). As a consequence and for about 10 years now, Chinese authorities have been working to reduce pollutant levels, because atmospheric pollution is a major health issue for Chinese population especially within cities, for which World Health Organisation's standards for major pollutants (Ozone, PM2.5, PM10) are often exceeded. Particles have multiple issues, as they impact on health and global warming. Their impacts will depend on their sources (primary or secondary pollutants) and natures (Particle size distribution, chemical composition…). Controlling particles loading is a complex task as their sources are various and dispersed on the Chinese territories: mineral dust can be emitted from Chinese deserts in large amount (Laurent et al., GPC, 2006), ammonia can be emitted from agriculture and livestock (Kang et al., ACP, 2016) and lots of urban primary pollutants can be emitted from urbanized areas. It is then necessary to work from a continental to local scales to understand more precisely pollution of urbanized areas. It is then mandatory to discriminate and quantify pollution sources and to estimate the impact of natural pollution and the major contributing sources. We propose here an approach based on a model and satellite observation synergy to estimate what controls Chinese pollution. We use the regional chemistry transport model CHIMERE (Menut et al., GMD, 2013) to simulate atmospheric pollutants concentrations. A large domain (72°E-145°E; 17.5°N-55°N), with a ¼°x¼° resolution is used to make multi-annual simulations. CHIMERE model include most of the pollutants

  8. From prototype to product

    DEFF Research Database (Denmark)

    Andersen, Tariq Osman; Bansler, Jørgen P.; Kensing, Finn

    2017-01-01

    This paper delves into the challenges of engaging patients, clinicians and industry stakeholders in the participatory design of an mHealth platform for patient-clinician collaboration. It follows the process from the development of a research prototype to a commercial software product. In particu......This paper delves into the challenges of engaging patients, clinicians and industry stakeholders in the participatory design of an mHealth platform for patient-clinician collaboration. It follows the process from the development of a research prototype to a commercial software product....... In particular, we draw attention to four major challenges of (a) aligning the different concerns of patients and clinicians, (b) designing according to clinical accountability, (c) ensuring commercial interest, and (d) dealing with regulatory constraints when prototyping safety critical health Information...... Technology. Using four illustrative cases, we discuss what these challenges entail and the implications they pose to Participatory Design. We conclude the paper by presenting lessons learned....

  9. PANDA Muon System Prototype

    Science.gov (United States)

    Abazov, Victor; Alexeev, Gennady; Alexeev, Maxim; Frolov, Vladimir; Golovanov, Georgy; Kutuzov, Sergey; Piskun, Alexei; Samartsev, Alexander; Tokmenin, Valeri; Verkheev, Alexander; Vertogradov, Leonid; Zhuravlev, Nikolai

    2018-04-01

    The PANDA Experiment will be one of the key experiments at the Facility for Antiproton and Ion Research (FAIR) which is under construction now in the territory of the GSI Helmholtz Centre for Heavy Ion Research in Darmstadt, Germany. PANDA is aimed to study hadron spectroscopy and various topics of the weak and strong forces. Muon System is chosen as the most suitable technology for detecting the muons. The Prototype of the PANDA Muon System is installed on the test beam line T9 at the Proton Synchrotron (PS) at CERN. Status of the PANDA Muon System prototype is presented with few preliminary results.

  10. Prototyping a Smart City

    DEFF Research Database (Denmark)

    Korsgaard, Henrik; Brynskov, Martin

    In this paper, we argue that by approaching the so-called Smart City as a design challenge, and an interaction design perspective, it is possible to both uncover existing challenges in the interplay between people, technology and society, as well as prototype possible futures. We present a case...... in which we exposed data about the online communication between the citizens and the municipality on a highly visible media facade, while at the same time prototyped a tool that enabled citizens to report ‘bugs’ within the city....

  11. PANDA Muon System Prototype

    Directory of Open Access Journals (Sweden)

    Abazov Victor

    2018-01-01

    Full Text Available The PANDA Experiment will be one of the key experiments at the Facility for Antiproton and Ion Research (FAIR which is under construction now in the territory of the GSI Helmholtz Centre for Heavy Ion Research in Darmstadt, Germany. PANDA is aimed to study hadron spectroscopy and various topics of the weak and strong forces. Muon System is chosen as the most suitable technology for detecting the muons. The Prototype of the PANDA Muon System is installed on the test beam line T9 at the Proton Synchrotron (PS at CERN. Status of the PANDA Muon System prototype is presented with few preliminary results.

  12. LEP vacuum chamber, prototype

    CERN Multimedia

    CERN PhotoLab

    1983-01-01

    Final prototype for the LEP vacuum chamber, see 8305170 for more details. Here we see the strips of the NEG pump, providing "distributed pumping". The strips are made from a Zr-Ti-Fe alloy. By passing an electrical current, they were heated to 700 deg C.

  13. Imagining the prototype

    NARCIS (Netherlands)

    Brouwer, C. E.; Bhomer, ten M.; Melkas, H.; Buur, J.

    2013-01-01

    This article reports on the analysis of a design session, employing conversation analysis. In the design session three experts and a designer discuss a prototype of a shirt, which has been developed with the input from these experts. The analysis focuses on the type of involvement of the

  14. The prototype fast reactor

    International Nuclear Information System (INIS)

    Broomfield, A.M.

    1985-01-01

    The paper concerns the Prototype Fast Reactor (PFR), which is a liquid metal cooled fast reactor power station, situated at Dounreay, Scotland. The principal design features of a Fast Reactor and the PFR are given, along with key points of operating history, and health and safety features. The role of the PFR in the development programme for commercial reactors is discussed. (U.K.)

  15. AGS Booster prototype magnets

    Energy Technology Data Exchange (ETDEWEB)

    Danby, G.; Jackson, J.; Lee, Y.Y.; Phillips, R.; Brodowski, J.; Jablonski, E.; Keohane, G.; McDowell, B.; Rodger, E.

    1987-03-19

    Prototype magnets have been designed and constructed for two half cells of the AGS Booster. The lattice requires 2.4m long dipoles, each curved by 10/sup 0/. The multi-use Booster injector requires several very different standard magnet cycles, capable of instantaneous interchange using computer control from dc up to 10 Hz.

  16. AGS booster prototype magnets

    International Nuclear Information System (INIS)

    Danby, G.; Jackson, J.; Lee, Y.Y.; Phillips, R.; Brodowski, J.; Jablonski, E.; Keohane, G.; McDowell, B.; Rodger, E.

    1987-01-01

    Prototype magnets have been designed and constructed for two half cells of the AGS Booster. The lattice requires 2.4m long dipoles, each curved by 10 0 . The multi-use Booster injector requires several very different standard magnet cycles, capable of instantaneous interchange using computer control from dc up to 10 Hz

  17. Cockroft Walton accelerator prototype

    International Nuclear Information System (INIS)

    Hutapea, Sumihar.

    1976-01-01

    Prototype of a Cockroft Walton generator using ceramic and plastic capacitors is discussed. Compared to the previous generator, the construction and components are much more improved. Pralon is used for the high voltage insulation column and plastic is used as a dielectric material for the high voltage capacitor. Cockroft Walton generator is used as a high tension supply for an accelerator. (author)

  18. Prompt and Precise Prototyping

    Science.gov (United States)

    2003-01-01

    For Sanders Design International, Inc., of Wilton, New Hampshire, every passing second between the concept and realization of a product is essential to succeed in the rapid prototyping industry where amongst heavy competition, faster time-to-market means more business. To separate itself from its rivals, Sanders Design aligned with NASA's Marshall Space Flight Center to develop what it considers to be the most accurate rapid prototyping machine for fabrication of extremely precise tooling prototypes. The company's Rapid ToolMaker System has revolutionized production of high quality, small-to-medium sized prototype patterns and tooling molds with an exactness that surpasses that of computer numerically-controlled (CNC) machining devices. Created with funding and support from Marshall under a Small Business Innovation Research (SBIR) contract, the Rapid ToolMaker is a dual-use technology with applications in both commercial and military aerospace fields. The advanced technology provides cost savings in the design and manufacturing of automotive, electronic, and medical parts, as well as in other areas of consumer interest, such as jewelry and toys. For aerospace applications, the Rapid ToolMaker enables fabrication of high-quality turbine and compressor blades for jet engines on unmanned air vehicles, aircraft, and missiles.

  19. Surrogates-based prototyping

    NARCIS (Netherlands)

    Du Bois, E.; Horvath, I.

    2014-01-01

    The research is situated in the system development phase of interactive software products. In this detailed design phase, we found a need for fast testable prototyping to achieve qualitative change proposals on the system design. In this paper, we discuss a literature study on current software

  20. Z Andromedae: the prototype

    International Nuclear Information System (INIS)

    Viotti, R.; Giangrande, A.; Ricciardi, O.; Cassatella, A.

    1982-01-01

    Z And is considered as the ''prototype'' of the symbiotic stars. Besides its symbiotic spectrum, the star is also known for its characteristic light curve (and for the related spectral variations). Since many theoretical speculations on Z And and similar objects have been based on the luminosity and spectral variations of this star, the authors critically analyse the observational data concerning it. (Auth.)

  1. Prototype ATLAS straw tracker

    CERN Multimedia

    Laurent Guiraud

    1998-01-01

    This is an early prototype of the straw tracking device for the ATLAS detector at CERN. This detector will be part of the LHC project, scheduled to start operation in 2008. The straw tracker will consist of thousands of gas-filled straws, each containing a wire, allowing the tracks of particles to be followed.

  2. Courthouse Prototype Building

    Energy Technology Data Exchange (ETDEWEB)

    Malhotra, Mini [ORNL; New, Joshua Ryan [ORNL; Im, Piljae [ORNL

    2018-02-01

    As part of DOE's support of ANSI/ASHRAE/IES Standard 90.1 and IECC, researchers at Pacific Northwest National Laboratory (PNNL) apply a suite of prototype buildings covering 80% of the commercial building floor area in the U.S. for new construction. Efforts have started on expanding the prototype building suite to cover 90% of the commercial building floor area in the U.S., by developing prototype models for additional building types including place of worship, public order and safety, public assembly. Courthouse is courthouse is a sub-category under the “Public Order and Safety" building type category; other sub-categories include police station, fire station, and jail, reformatory or penitentiary.ORNL used building design guides, databases, and documented courthouse projects, supplemented by personal communication with courthouse facility planning and design experts, to systematically conduct research on the courthouse building and system characteristics. This report documents the research conducted for the courthouse building type and proposes building and system characteristics for developing a prototype building energy model to be included in the Commercial Building Prototype Model suite. According to the 2012 CBECS, courthouses occupy a total of 436 million sqft of floor space or 0.5% of the total floor space in all commercial buildings in the US, next to fast food (0.35%), grocery store or food market (0.88%), and restaurant or cafeteria (1.2%) building types currently included in the Commercial Prototype Building Model suite. Considering aggregated average, courthouse falls among the larger with a mean floor area of 69,400 sqft smaller fuel consumption intensity building types and an average of 94.7 kBtu/sqft compared to 77.8 kBtu/sqft for office and 80 kBtu/sqft for all commercial buildings.Courthouses range in size from 1000 sqft to over a million square foot building gross square feet and 1 courtroom to over 100 courtrooms. Small courthouses

  3. Aggregate and Mineral Resources - Minerals

    Data.gov (United States)

    NSGIC State | GIS Inventory — This point occurrence data set represents the current mineral and selected energy resources of Utah. The data set coordinates were derived from USGS topographic maps...

  4. Late Triassic porphyritic intrusions and associated volcanic rocks from the Shangri-La region, Yidun terrane, Eastern Tibetan Plateau: Adakitic magmatism and porphyry copper mineralization

    Science.gov (United States)

    Wang, Bai-Qiu; Zhou, Mei-Fu; Li, Jian-Wei; Yan, Dan-Ping

    2011-11-01

    Early Mesozoic porphyritic intrusions in the Shangri-La region, southern Yidun terrane, SW China, are spatially associated with andesites and dacites. These intrusions are composed of diorite and quartz diorite, and are closely related to copper mineralization. LA-ICP-MS zircon U-Pb ages of the intrusions range from 230 to 215 Ma. The associated andesites and dacites are interlayered with slates and sandstones and have ages of around 220 Ma. All of the intrusive and extrusive rocks have similar, highly fractionated REE patterns and high La/Yb (13-49) ratios with no prominent Eu anomalies. They display pronounced negative Nb-Ta and Ti anomalies on primitive mantle-normalized spidergrams. Their SiO2 contents range from 56.6 to 67.1 wt.%, Al2O3 from 14.2 to 17.4 wt.% and MgO from1.9 to 4.2 wt.%. All the rocks have high Sr (258-1980 ppm), and low Y (13-21 ppm) with high Sr/Y ratios (29-102). These features suggest that both the volcanic rocks and porphyritic intrusions were derived from adakitic magmas. They have similar initial 87Sr/86Sr ratios (0.7058 to 0.7077) and εNd (- 1.88 to - 4.93) values, but belong to high silica (HSA) and low silica adakitic rocks (LSA). The HSA represent an early stage of magmatism (230 to 215 Ma) and were derived from oceanic slab melts with limited interaction with the overlying mantle wedge during ascent. At 215 Ma, more extensive interaction produced the LSA. We propose that the early adakitic magmas (HSA) formed by flat subduction leading to melting of oceanic slab, whereas subsequent slab break-off caused the significant interaction between slab melts and the mantle wedge and thus the generation of the later adakitic magmas (LSA).

  5. Occupational and environmental mercury exposure among small-scale gold miners in the Talensi-Nabdam District of Ghana's Upper East region.

    Science.gov (United States)

    Paruchuri, Yasaswi; Siuniak, Amanda; Johnson, Nicole; Levin, Elena; Mitchell, Katherine; Goodrich, Jaclyn M; Renne, Elisha P; Basu, Niladri

    2010-11-15

    Mercury use in small-scale gold mining is ubiquitous across Ghana but little is known about the extent to which such activities have contaminated community residents and miners. Here, occupational exposures to elemental mercury (via urine sampling) and dietary exposures to methylmercury (via hair sampling) were assessed among 120 participants recruited from a mining community located in the Talensi-Nabdam District of Ghana's Upper East region during summer 2009. More than one-fifth of the participants had moderately high levels of urinary mercury (>10μg/L) and 5% had urine mercury levels that exceeded the WHO guideline value of 50μg/L. When participants were stratified according to occupation, those active in the mining industry had the highest mercury levels. Specifically, individuals that burned amalgam had urine mercury levels (median: 43.8μg/L; mean ± SD: 171.1±296.5μg/L; n=5) significantly higher than median values measured in mechanical operators (11.6μg/L, n=4), concession managers/owners (5.6μg/L, n=11), excavators that blast and chisel ore (4.9μg/L, n=33), individuals that sift and grind crushed ore (2.2μg/L, n=47), support workers (0.5μg/L, n=14), and those with no role in the mining sector (2.5μg/L, n=6). There was a significant positive Spearman correlation between fish consumption and hair mercury levels (r=0.30) but not with urine mercury (r=0.18) though further studies are needed to document which types of fish are consumed as well as portion sizes. Given that 200,000 people in Ghana are involved in the small-scale gold mining industry and that the numbers are expected to grow in Ghana and many other regions of the world, elucidating mercury exposure pathways in such communities is important to help shape policies and behaviors that may minimize health risks. Copyright © 2010 Elsevier B.V. All rights reserved.

  6. Occupational and environmental mercury exposure among small-scale gold miners in the Talensi-Nabdam District of Ghana’s Upper East region

    Science.gov (United States)

    Paruchuri, Yasaswi; Siuniak, Amanda; Johnson, Nicole; Levin, Elena; Mitchell, Katherine; Goodrich, Jaclyn M.; Renne, Elisha P.; Basu, Niladri

    2014-01-01

    Mercury use in small-scale gold mining is ubiquitous across Ghana but little is known about the extent to which such activities have contaminated community residents and miners. Here, occupational exposures to elemental mercury (via urine sampling) and dietary exposures to methylmercury (via hair sampling) were assessed among 120 participants recruited from a mining community located in the Talensi-Nabdam District of Ghana’s Upper East region during summer 2009. More than one-fifth of the participants had moderately high levels of urinary mercury (>10 µg/L) and 5% had urine mercury levels that exceeded the WHO guideline value of 50 µg/L. When participants were stratified according to occupation, those active in the mining industry had the highest mercury levels. Specifically, individuals that burned amalgam had urine mercury levels (median: 43.8 µg/L; mean ± SD: 171.1 ± 296.5 µg/L; n=5) significantly higher than median values measured in mechanical operators (11.6 µg/L, n=4), concession managers/owners (5.6 µg/L, n=11), excavators that blast and chisel ore (4.9 µg/L, n=33), individuals that sift and grind crushed ore (2.2 µg/L, n=47), support workers (0.5 µg/L, n=14), and those with no role in the mining sector (2.5 µg/L, n=6). There was a significant positive spearman correlation between fish consumption and hair mercury levels (r = 0.30) but not with urine mercury (r = 0.18) though further studies are needed to document which types of fish are consumed as well as portion sizes. Given that 200,000 people in Ghana are involved in the small-scale gold mining industry and that the numbers are expected to grow in Ghana and many other regions of the world, elucidating mercury exposure pathways in such communities is important to help shape policies and behaviors that may minimize health risks. PMID:20875913

  7. Database Replication Prototype

    OpenAIRE

    Vandewall, R.

    2000-01-01

    This report describes the design of a Replication Framework that facilitates the implementation and com-parison of database replication techniques. Furthermore, it discusses the implementation of a Database Replication Prototype and compares the performance measurements of two replication techniques based on the Atomic Broadcast communication primitive: pessimistic active replication and optimistic active replication. The main contributions of this report can be split into four parts....

  8. Brachial Plexus Blocker Prototype

    OpenAIRE

    Stéphanie Coelho Monteiro

    2017-01-01

    Although the area of surgical simulation has been the subject of study in recent years, it is still necessary to develop artificial experimental models with a perspective to dismiss the use of biological models. Since this makes the simulators more real, transferring the environment of the health professional to a physical or virtual reality, an anesthetic prototype has been developed, where the motor response is replicated when the brachial plexus is subjected to a proximal nervous stimulus....

  9. Fumarolic minerals

    DEFF Research Database (Denmark)

    Balic Zunic, Tonci; Garavelli, Anna; Jakobsson, Sveinn Peter

    2016-01-01

    The fumarolic mineralogy of the Icelandic active volcanoes, the Tyrrhenian volcanic belt (Italy) and the Aegean active arc (Greece) is investigated, and literature data surveyed in order to define the characteristics of the European fumarolic systems. They show broad diversity of mineral...... associations, with Vesuvius and Vulcano being also among the world localities richest in mineral species. Volcanic systems, which show recession over a longer period, show fumarolic development from the hightemperature alkaline halide/sulphate, calcic sulphate or sulphidic parageneses, synchronous...... with or immediately following the eruptions, through mediumtemperature ammonium minerals, metal chlorides, or fluoride associations to the late low-temperature paragenesis dominated by sulphur, gypsum, alunogen, and other hydrous sulphates. The situation can be different in the systems that are not recessing but show...

  10. Prototyping real-time systems

    OpenAIRE

    Clynch, Gary

    1994-01-01

    The traditional software development paradigm, the waterfall life cycle model, is defective when used for developing real-time systems. This thesis puts forward an executable prototyping approach for the development of real-time systems. A prototyping system is proposed which uses ESML (Extended Systems Modelling Language) as a prototype specification language. The prototyping system advocates the translation of non-executable ESML specifications into executable LOOPN (Language of Object ...

  11. MITRE sensor layer prototype

    Science.gov (United States)

    Duff, Francis; McGarry, Donald; Zasada, David; Foote, Scott

    2009-05-01

    The MITRE Sensor Layer Prototype is an initial design effort to enable every sensor to help create new capabilities through collaborative data sharing. By making both upstream (raw) and downstream (processed) sensor data visible, users can access the specific level, type, and quantities of data needed to create new data products that were never anticipated by the original designers of the individual sensors. The major characteristic that sets sensor data services apart from typical enterprise services is the volume (on the order of multiple terabytes) of raw data that can be generated by most sensors. Traditional tightly coupled processing approaches extract pre-determined information from the incoming raw sensor data, format it, and send it to predetermined users. The community is rapidly reaching the conclusion that tightly coupled sensor processing loses too much potentially critical information.1 Hence upstream (raw and partially processed) data must be extracted, rapidly archived, and advertised to the enterprise for unanticipated uses. The authors believe layered sensing net-centric integration can be achieved through a standardize-encapsulate-syndicateaggregate- manipulate-process paradigm. The Sensor Layer Prototype's technical approach focuses on implementing this proof of concept framework to make sensor data visible, accessible and useful to the enterprise. To achieve this, a "raw" data tap between physical transducers associated with sensor arrays and the embedded sensor signal processing hardware and software has been exploited. Second, we encapsulate and expose both raw and partially processed data to the enterprise within the context of a service-oriented architecture. Third, we advertise the presence of multiple types, and multiple layers of data through geographic-enabled Really Simple Syndication (GeoRSS) services. These GeoRSS feeds are aggregated, manipulated, and filtered by a feed aggregator. After filtering these feeds to bring just the type

  12. Mineral sands

    International Nuclear Information System (INIS)

    Anon.

    1990-01-01

    This paper presents an outlook of the Australian mineral sand industry and covers the major operators. It is shown that conscious of an environmentally minded public, the Australian miners have led the way in the rehabilitation of mined areas. Moreover the advanced ceramic industry is generating exciting new perspectives for zircon producers and there is a noticeable growth in the electronic market for rare earths, but in long term the success may depend as much on environmental management and communication skills as on mining and processing skills

  13. A prototype analysis of vengeance

    NARCIS (Netherlands)

    Elshout, Maartje; Nelissen, Rob; van Beest, Ilja

    2015-01-01

    The authors examined the concept of vengeance from a prototype perspective. In 6 studies, the prototype structure of vengeance was mapped. Sixty-nine features of vengeance were identified (Study 1), and rated on centrality (Study 2). Further studies confirmed the prototype structure. Compared to

  14. Mineral supplementation for grazing ruminants

    International Nuclear Information System (INIS)

    McDowell, L.R.; Conrad, J.H.; Ellis, G.L.

    1986-01-01

    Grazing ruminants to which concentrate feeds cannot be economically fed must rely on self-feeding of mineral supplements. A number of factors affect mineral consumption of free-choice mixtures. Livestock exhibit little nutritional wisdom and will select palatable mixtures in preference to mixtures designed to meet their requirements. Palatability and appetite stimulators are often used to achieve a more uniform herd-wide consumption. It is best to formulate free-choice mixtures on the basis of analyses or other available data. However, when no information on mineral status is known, a free-choice complete mineral supplement is warranted. A 'complete' mineral mixture usually includes salt, a low fluoride P source, Ca, Co, Cu, I, Mn and Zn. Selenium, Mg, K, S, Fe or additional elements can be incorporated into a mineral supplement as new information suggests a need. The detriment to ruminant production caused by providing Ca, Se and Cu in excess can be greater than any benefit derived by providing a mineral supplement. In regions where high forage Mo predominates, three to five times the Cu content in mineral mixtures is needed to counteract Mo toxicity. Supplemental minerals are most critical during the wet season, when cattle are gaining weight rapidly and energy and protein supplies are adequate. Economic return on mineral supplementation is high. (author)

  15. Brazil Geological Basic Survey Program: special project of mineral resources, soils and vegetation maps for the region of Grande Carajas Program - Mineral resources sub project - Serra dos Carajas - Sheet SB.22-Z-A - Para State

    International Nuclear Information System (INIS)

    Araujo, O.J.B. de; Maia, R.G.N.

    1991-01-01

    The geologic landscape at Serra dos Carajas Sheet encloses portions of Southern Para granite-greenstone terrain, Itacaiunas and Araguaia Belts as well as Proterozoic litho-structural components. It shows medium magnetic relief and low radiometric levels due to meta mafic-ultramafic sequences and the high Na granitoids intrusions. The Proterozoic components are represented by a series of anorogenic granitic intrusions shown by distinctive aero gamaspectrometric anomalies. The well known metallogenetic characteristics includes gold, iron, manganese, nickel and aluminium mines and/or deposits and several mineral occurrences mainly chromium, tin, copper, and zinc. (author)

  16. Spreading, Infestation and Damage Rates and Adult Population Monitoring of Tomato Leaf Miner [Tuta absoluta (Meyrick) (Lepidoptera: Gelechiidae)] on Open Field Tomato Grown in the South Marmara Region of Turkey

    OpenAIRE

    ÇETİN, Gürsel; GÖKSEL, Pınar; DURA, Onur; HANTAŞ, Cemil

    2014-01-01

    This study was conducted in order to determine spreading, infestation and fruit damage rates and adult population monitoring of Tomato leaf miner, (Tuta absoluta, Meyrick) on open field tomato grown in the South Marmara Region (Bilecik, Bursa, Kocaeli, Sakarya and Yalova provinces) of Turkey in 2011-2012. As result of spreading studies carried out according to systematic sampling method, it was determined that all tomato locations in every province were infested by this pest. Infestation rate...

  17. Late Triassic Porphyritic Intrusions And Associated Volcanic Rocks From The Shangri-La Region, Yidun Terrane, Eastern Tibetan Plateau: Implications For Adakitic Magmatism And Porphyry Copper Mineralization

    Science.gov (United States)

    Wang, B.; Zhou, M.; Li, J.; Yan, D.

    2011-12-01

    The Yidun terrane, located on the eastern margin of the Tibetan plateau, has been commonly considered to be a Triassic volcanic arc produced by subduction of the Ganzi-Litang oceanic lithosphere. The Yidun terrane is characterized by numerous arc-affinity granitic intrusions located along a 500-km-long, north-south-trending belt. Among these granitic bodies, several small porphyritic intrusions in the southern segment of the terrane (Shangri-La region) are associated with large porphyry copper deposits. These porphyritc intrusions are composed of diorite and quartz diorite, and spatially associated with andesites and dacites. LA-ICP-MS zircon U-Pb ages of the intrusions range from 230 to 215 Ma. The andesites and dacites are intercalated with slates and sandstones and have ages of around 220 Ma. The intrusive and volcanic rocks have SiO2 contents from 56.6 to 67.1 wt.%, Al2O3 from 14.2 to 17.4 wt.% and MgO from 1.9 to 4.2 wt.%. They show significant negative Nb-Ta anomalies on primitive mantle-normalized spidergrams. They have high La/Yb (13-49) ratios with no prominent Eu anomalies. All the rocks have high Sr (258-1980 ppm), and low Y (13-21 ppm) with high Sr/Y ratios (29-102). The geochemical features indicate that both the volcanic rocks and porphyritic intrusions were derived from adakitic magmas. They have similar initial 87Sr/86Sr ratios (0.7058 to 0.7077) and ɛNd (-1.88 to -4.93) values, but can be further divided into two groups: high silica (HSA) and low silica adakitic rocks (LSA). The HSA, representing an early stage of magmatism (230 to 215 Ma), were derived from oceanic slab melts with limited interaction with the overlying mantle wedge. At 215 Ma, more extensive interaction resulted in the formation of LSA. We propose that HSA were produced by flat subduction leading to melting of oceanic slab, whereas subsequent slab break-off caused the significant interaction between slab melts and the mantle wedge and thus the generation of the LSA. Compared with

  18. OPAL Jet Chamber Prototype

    CERN Multimedia

    OPAL was one of the four experiments installed at the LEP particle accelerator from 1989 - 2000. OPAL's central tracking system consists of (in order of increasing radius) a silicon microvertex detector, a vertex detector, a jet chamber, and z-chambers. All the tracking detectors work by observing the ionization of atoms by charged particles passing by: when the atoms are ionized, electrons are knocked out of their atomic orbitals, and are then able to move freely in the detector. These ionization electrons are detected in the dirfferent parts of the tracking system. This piece is a prototype of the jet chambers

  19. Prototyping Augmented Reality

    CERN Document Server

    Mullen, Tony

    2011-01-01

    Learn to create augmented reality apps using Processing open-source programming language Augmented reality (AR) is used all over, and you may not even realize it. Smartphones overlay data onto live camera views to show homes for sale, restaurants, or historical sites. American football broadcasts use AR to show the invisible first-down line on the field to TV viewers. Nike and Budweiser, among others, have used AR in ads. Now, you can learn to create AR prototypes using 3D data, Processing open-source programming language, and other languages. This unique book is an easy-to-follow guide on how

  20. Nightshade Prototype Experiments (Silverleaf)

    Energy Technology Data Exchange (ETDEWEB)

    Danielson, Jeremy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Bauer, Amy L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-12-23

    The Red Sage campaign is a series of subcritical dynamic plutonium experiments designed to measure ejecta. Nightshade, the first experiments in Red Sage scheduled for fiscal year 2019, will measure the amount of ejecta emission into vacuum from a double-­shocked plutonium surface. To address the major technical risks in Nightshade, a Level 2 milestone was developed for fiscal year 2016. Silverleaf, a series of four experiments, was executed at the Los Alamos National Laboratory in July and August 2016 to demonstrate a prototype of the Nightshade package and to satisfy this Level 2 milestone. This report is documentation that Red Sage Level 2 milestone requirements were successfully met.

  1. Contribution to the geologic evolution from the Eastern part of Central Amazonia Province by Rb-Sr geochronology from the Carajas Mineral Province and the Sao Felix do Xingu region, Para State

    International Nuclear Information System (INIS)

    Pereira, Edilea Dutra.

    1992-01-01

    This work deals with a Rb/Sr geochronological study carried on granitoids and granulites of the Carajas Mineral Province (Rio Maria, Serra dos Gradaus and Serra do Pium regions) and Sao Felix do Xingu regions. The Manelao and Ourilandia granitoids of the Sao Felix do Xingu region are associated with the greenstone terrains of the Tucuma Group, and yield an age of 2749 ± 24 Ma with an initial ratio of 0.07028 ± 19, and 2677 ± 50 Ma with an initial ratio of 0.07016 ± 22, respectively. In the Rio Maria region, an age of 2541 ± 74 Ma with an initial ratio of 0.7104 ± 343 was obtained on the Mata Surrao Granite located near the Marajoara Village. This age confirms an archaean monzogranitic magmatism in this region. In the Gradaus area, the Cumaru Granodiorite give an mineral age of 2577 ± 27 Ma similar to the age obtained by whole rock method. Finally, Rb/Sr ages were obtained from granulitic rocks of the Pium Complex located at the Serra do Pium and near the Catete River. Samples of the Serra do Pium yielded ages of 2325 ± 71 Ma (whole rock) and 1857 ± 48 (minerals). Samples from the Catete River area give a whole rock age of 2018 ± 25 Ma with an initial ratio of 0.7039 ± 25. These data show that the Rb/Sr system in these granulitic rocks suffered changes during the Early Proterozoic times. The geochronological data here obtained confirm promptly an Archaean evolution in the studied regions, besides give rise the discussion about the problem related to the Transamazonian Event inside them. (author). 92 refs., 32 figs., 10 tabs

  2. OMS FDIR: Initial prototyping

    Science.gov (United States)

    Taylor, Eric W.; Hanson, Matthew A.

    1990-01-01

    The Space Station Freedom Program (SSFP) Operations Management System (OMS) will automate major management functions which coordinate the operations of onboard systems, elements and payloads. The objectives of OMS are to improve safety, reliability and productivity while reducing maintenance and operations cost. This will be accomplished by using advanced automation techniques to automate much of the activity currently performed by the flight crew and ground personnel. OMS requirements have been organized into five task groups: (1) Planning, Execution and Replanning; (2) Data Gathering, Preprocessing and Storage; (3) Testing and Training; (4) Resource Management; and (5) Caution and Warning and Fault Management for onboard subsystems. The scope of this prototyping effort falls within the Fault Management requirements group. The prototyping will be performed in two phases. Phase 1 is the development of an onboard communications network fault detection, isolation, and reconfiguration (FDIR) system. Phase 2 will incorporate global FDIR for onboard systems. Research into the applicability of expert systems, object-oriented programming, fuzzy sets, neural networks and other advanced techniques will be conducted. The goals and technical approach for this new SSFP research project are discussed here.

  3. Live Piloting and Prototyping

    Directory of Open Access Journals (Sweden)

    Francesca Rizzo

    2013-07-01

    Full Text Available This paper presents current trends in service design research concerning large scale projects aimed at generating changes at a local scale. The strategy adopted to achieve this, is to co-design solutions including future users in the development process, prototyping and testing system of products and services before their actual implementation. On the basis of experience achieved in the European Project Life 2.0, this paper discusses which methods and competencies are applied in the development of these projects, eliciting the lessons learnt especially from the piloting phase in which the participatory design (PD approach plays a major role. In the first part, the topic is introduced jointly with the theoretical background where the user center design and participatory design methods are presented; then the Life 2.0 project development is described; finally the experience is discussed from a service design perspective, eliciting guidelines for piloting and prototyping services in a real context of use. The paper concludes reflecting on the designers’ role and competencies needed in this process.

  4. Hydrothermal minerals

    Digital Repository Service at National Institute of Oceanography (India)

    Nath, B.N.

    flux. Circulation of seawater through the oceanic crust and upper mantle gives rise to a complex series of physical and chemical reactions that lead to the 1) formation of seafloor mineral deposits; 2) alteration of oceanic crust; 3) control... temperature in the high-temperature reaction zone near the heat source. Important parameters in determining the high- temperature fluid composition are • pressure, • temperature, • water/rock ratio, • rock composition, • recharge fluid...

  5. The effects of sleep deprivation on dissociable prototype learning systems.

    Science.gov (United States)

    Maddox, W Todd; Glass, Brian D; Zeithamova, Dagmar; Savarie, Zachary R; Bowen, Christopher; Matthews, Michael D; Schnyer, David M

    2011-03-01

    The cognitive neural underpinnings of prototype learning are becoming clear. Evidence points to 2 different neural systems, depending on the learning parameters. A/not-A (AN) prototype learning is mediated by posterior brain regions that are involved in early perceptual learning, whereas A/B (AB) is mediated by frontal and medial temporal lobe regions. To investigate the effects of sleep deprivation on AN and AB prototype learning and to use established prototype models to provide insights into the cognitive-processing locus of sleep-deprivation deficits. Participants performed an AN and an AB prototype learning task twice, separated by a 24-hour period, with or without sleep between testing sessions. Eighteen West Point cadets participated in the sleep-deprivation group, and 17 West Point cadets participated in a control group. Sleep deprivation led to an AN, but not an AB, performance deficit. Prototype model analyses indicated that the AN deficit was due to changes in attentional focus and a decrease in confidence that is reflected in an increased bias to respond non-A. The findings suggest that AN, but not AB, prototype learning is affected by sleep deprivation. Prototype model analyses support the notion that the effect of sleep deprivation on AN is consistent with lapses in attentional focus that are more detrimental to AN than to AB. This finding adds to a growing body of work that suggests that different performance changes associated with sleep deprivation can be attributed to a common mechanism of changes in simple attention and vigilance.

  6. Iodine mineral waters

    Directory of Open Access Journals (Sweden)

    Iluta Alexandru

    2011-11-01

    Full Text Available Iodine mineral waters are found especially in sub-Carpathian region, also in regions with Salif deposits. Waters are currently used iodine in drinking cure for chaps and Basedow. Are also indicated in balneology. Iodine water containing at least 1 mg L, there is pure iodine is usually given the nature of other types of mineral waters further: sodium chlorinated water (Bazna (50-70 mg iodine / l, Baile Govora (50 - 70 mg / l, Bălţăteşti (4-5 mg / l, salted Monteoru (30 mg / l, mine water mixed alkaline chlorination, sulphate, which are indicated for crenoterapie (hypo or isotonic to the bathrooms Olăneşti or Călimăneşti-Căciulata.

  7. Prototypes as Platforms for Participation

    DEFF Research Database (Denmark)

    Horst, Willem

    developers, and design it accordingly. Designing a flexible prototype in combination with supportive tools to be used by both interaction designers and non-designers during development is introduced as a way to open up the prototyping process to these users. Furthermore I demonstrate how such a flexible...... on prototyping, by bringing to attention that the prototype itself is an object of design, with its users and use context, which deserves further attention. Moreover, in this work I present concrete tools and methods that can be used by interaction designers in practice. As such this work addresses both......The development of interactive products in industry is an activity involving different disciplines – such as different kinds of designers, engineers, marketers and managers – in which prototypes play an important role. On the one hand, prototypes can be powerful boundary objects and an effective...

  8. Prototype Stilbene Neutron Collar

    Energy Technology Data Exchange (ETDEWEB)

    Prasad, M. K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Shumaker, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Snyderman, N. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Verbeke, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wong, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-10-26

    A neutron collar using stilbene organic scintillator cells for fast neutron counting is described for the assay of fresh low enriched uranium (LEU) fuel assemblies. The prototype stilbene collar has a form factor similar to standard He-3 based collars and uses an AmLi interrogation neutron source. This report describes the simulation of list mode neutron correlation data on various fuel assemblies including some with neutron absorbers (burnable Gd poisons). Calibration curves (doubles vs 235U linear mass density) are presented for both thermal and fast (with Cd lining) modes of operation. It is shown that the stilbene collar meets or exceeds the current capabilities of He-3 based neutron collars. A self-consistent assay methodology, uniquely suited to the stilbene collar, using triples is described which complements traditional assay based on doubles calibration curves.

  9. Brachial Plexus Blocker Prototype

    Directory of Open Access Journals (Sweden)

    Stéphanie Coelho Monteiro

    2017-08-01

    Full Text Available Although the area of surgical simulation has been the subject of study in recent years, it is still necessary to develop artificial experimental models with a perspective to dismiss the use of biological models. Since this makes the simulators more real, transferring the environment of the health professional to a physical or virtual reality, an anesthetic prototype has been developed, where the motor response is replicated when the brachial plexus is subjected to a proximal nervous stimulus. Using action-research techniques, with this simulator it was possible to validate that the human nerve response can be replicated, which will aid the training of health professionals, reducing possible risks in a surgical environment.

  10. Effect of Residue Nitrogen Concentration and Time Duration on Carbon Mineralization Rate of Alfalfa Residues in Regions with Different Climatic Conditions

    Directory of Open Access Journals (Sweden)

    saeid shafiei

    2017-08-01

    Full Text Available Introduction Various factors like climatic conditions, vegetation, soil properties, topography, time, plant residue quality and crop management strategies affect the decomposition rate of organic carbon (OC and its residence time in soil. Plant residue management concerns nutrients recycling, carbon recycling in ecosystems and the increasing CO2 concentration in the atmosphere. Plant residue decomposition is a fundamental process in recycling of organic matter and elements in most ecosystems. Soil management, particularly plant residue management, changes soil organic matter both qualitatively and quantitatively. Soil respiration and carbon loss are affected by soil temperature, soil moisture, air temperature, solar radiation and precipitation. In natural agro-ecosystems, residue contains different concentrations of nitrogen. It is important to understand the rate and processes involved in plant residue decomposition, as these residues continue to be added to the soil under different weather conditions, especially in arid and semi-arid climates. Material and methods Organic carbon mineralization of alfalfa residue with different nitrogen concentrations was assessed in different climatic conditions using split-plot experiments over time and the effects of climate was determined using composite analysis. The climatic conditions were classified as warm-arid (Jiroft, temperate arid (Narab and cold semi-arid (Sardouiyeh using cluster analysis and the nitrogen (N concentrations of alfalfa residue were low, medium and high. The alfalfa residue incubated for four different time periods (2, 4, 6 and 8 months. The dynamics of organic carbon in different regions measured using litter bags (20×10 cm containing 20 g alfalfa residue of 2-10 mm length which were placed on the soil surface. Results and discussion The results of this study showed that in a warm-arid (Jiroft, carbon loss and the carbon decomposition rate constant were low in a cold semi

  11. WorldSID Prototype Dummy Biomechanical Responses.

    Science.gov (United States)

    Cesari, D; Compigne, S; Scherer, R; Xu, L; Takahashi, N; Page, M; Asakawa, K; Kostyniuk, G; Hautmann, E; Bortenschlager, K; Sakurai, M; Harigae, T

    2001-11-01

    The results of biomechanical testing of the WorldSID prototype dummy are presented in this paper. The WorldSID dummy is a new, advanced Worldwide Side Impact Dummy that has the anthropometry of a mid-sized adult male. The first prototype of this dummy has been evaluated by the WorldSID Task Group against previously established corridors for its critical body regions. The response corridors are defined in the International Organization of Standardization (ISO) Technical Report 9790. The prototype is the first version of the WorldSID dummy to be built and tested. This dummy has been subjected to a rigorous program of testing to evaluate, first and foremost its biofidelity, but also its repeatability. Following this initial evaluation, any required modifications will be incorporated into a pre-production version of the WorldSID dummy so that it rates "good" to "excellent" on the ISO dummy biofidelity scale - a rating exceeding that of all current side impact dummies. Also, the overall WorldSID repeatability must not exceed a coefficient of variation of 7% at injury assessment level and this has to be verified for the different body regions. The dummy's head, neck, thorax, abdomen and pelvis were evaluated against the ISO technical report requirements. Testing included drop tests, pendulum impacts, and sled tests. The biofidelity rating of the WorldSID prototype was calculated using the weighted biomechanical test response procedure developed by ISO. The paper presents the results of the testing, which give a very positive indication of the dummy's potential. Based on this evaluation of the dummy biofidelity, the WorldSID prototype dummy exhibits a biofidelity rating of 6.15 that corresponds to an ISO biofidelity classification of "fair". In addition, the dummy shows good repeatability with a global coefficient of variation of 3.30% for the pendulum and rigid sled tests.

  12. Naval Prototype Optical Interferometer (NPOI)

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Used for astrometry and astronomical imaging, the Naval Prototype Optical Interferometer (NPOI) is a distributed aperture optical telescope. It is operated...

  13. Mobile prototyping with Axure 7

    CERN Document Server

    Hacker, Will

    2013-01-01

    This book is a step-by-step tutorial which includes hands-on examples and downloadable Axure files to get you started with mobile prototyping immediately. You will learn how to develop an application from scratch, and will be guided through each and every step.If you are a mobile-centric developer/designer, or someone who would like to take their Axure prototyping skills to the next level and start designing and testing mobile prototypes, this book is ideal for you. You should be familiar with prototyping and Axure specifically, before you read this book.

  14. Microbially mediated mineral carbonation

    Science.gov (United States)

    Power, I. M.; Wilson, S. A.; Dipple, G. M.; Southam, G.

    2010-12-01

    Mineral carbonation involves silicate dissolution and carbonate precipitation, which are both natural processes that microorganisms are able to mediate in near surface environments (Ferris et al., 1994; Eq. 1). (Ca,Mg)SiO3 + 2H2CO3 + H2O → (Ca,Mg)CO3 + H2O + H4SiO4 + O2 (1) Cyanobacteria are photoautotrophs with cell surface characteristics and metabolic processes involving inorganic carbon that can induce carbonate precipitation. This occurs partly by concentrating cations within their net-negative cell envelope and through the alkalinization of their microenvironment (Thompson & Ferris, 1990). Regions with mafic and ultramafic bedrock, such as near Atlin, British Columbia, Canada, represent the best potential sources of feedstocks for mineral carbonation. The hydromagnesite playas near Atlin are a natural biogeochemical model for the carbonation of magnesium silicate minerals (Power et al., 2009). Field-based studies at Atlin and corroborating laboratory experiments demonstrate the ability of a microbial consortium dominated by filamentous cyanobacteria to induce the precipitation of carbonate minerals. Phototrophic microbes, such as cyanobacteria, have been proposed as a means for producing biodiesel and other value added products because of their efficiency as solar collectors and low requirement for valuable, cultivable land in comparison to crops (Dismukes et al., 2008). Carbonate precipitation and biomass production could be facilitated using specifically designed ponds to collect waters rich in dissolved cations (e.g., Mg2+ and Ca2+), which would allow for evapoconcentration and provide an appropriate environment for growth of cyanobacteria. Microbially mediated carbonate precipitation does not require large quantities of energy or chemicals needed for industrial systems that have been proposed for rapid carbon capture and storage via mineral carbonation (e.g., Lackner et al., 1995). Therefore, this biogeochemical approach may represent a readily

  15. Minerals From the Marine Environment

    Science.gov (United States)

    Cruickshank, Michael J.

    The current interest in minerals centering on, among other things, potential shortages, long-term needs, and deep seabed nodules, accentuates the usefulness and timeliness of this little book authored by a former chairman of the British National Environmental Research Council.In less than 100 pages, the author puts into perspective the potential for producing minerals from offshore areas of the world. After introducing the reader to the ocean environment and the extraordinary variety of the nature of the seabed, the author describes in some detail the variety of minerals found there. This is done in seven separate chapters entitled ‘Bulk and Non-Metallic Minerals From the Seas’ ‘Metals From the Shallow Seas’ ‘Metals From the Deep Oceans’ ‘Minerals From Solution’ ‘Oil and Gas from the Shallow Seas’ ‘Oil and Gas From Deep Waters’ and ‘Coal Beneath the Sea.’ The remaining chapters give a brief regional review of marine minerals distribution for eight areas of significant socioeconomic structure, and a short recapitulation of special problems of mineral recovery in the marine environment including such matters as the effect of water motion on mineral processing and of international law on investments. Glossaries of geological periods and technical terms, a short list of references, and an index complete the work.

  16. Window prototypes during the project

    DEFF Research Database (Denmark)

    Schultz, Jørgen Munthe

    1996-01-01

    The conditions for the PASSYS test and the results of the measurements on one of the aerogel window prototypes are described.......The conditions for the PASSYS test and the results of the measurements on one of the aerogel window prototypes are described....

  17. Rapid prototyping: een veelbelovende methode

    NARCIS (Netherlands)

    Haverman, T.M.; Karagozoglu, K.H.; Prins, H.; Schulten, E.A.J.M.; Forouzanfar, T.

    2013-01-01

    Rapid prototyping is a method which makes it possible to produce a three-dimensional model based on two-dimensional imaging. Various rapid prototyping methods are available for modelling, such as stereolithography, selective laser sintering, direct laser metal sintering, two-photon polymerization,

  18. Role model and prototype matching

    DEFF Research Database (Denmark)

    Lykkegaard, Eva; Ulriksen, Lars

    2016-01-01

    ’ meetings with the role models affected their thoughts concerning STEM students and attending university. The regular self-to-prototype matching process was shown in real-life role-models meetings to be extended to a more complex three-way matching process between students’ self-perceptions, prototype...

  19. Virtual Prototyping at CERN

    Science.gov (United States)

    Gennaro, Silvano De

    The VENUS (Virtual Environment Navigation in the Underground Sites) project is probably the largest Virtual Reality application to Engineering design in the world. VENUS is just over one year old and offers a fully immersive and stereoscopic "flythru" of the LHC pits for the proposed experiments, including the experimental area equipment and the surface models that are being prepared for a territorial impact study. VENUS' Virtual Prototypes are an ideal replacement for the wooden models traditionally build for the past CERN machines, as they are generated directly from the EUCLID CAD files, therefore they are totally reliable, they can be updated in a matter of minutes, and they allow designers to explore them from inside, in a one-to-one scale. Navigation can be performed on the computer screen, on a stereoscopic large projection screen, or in immersive conditions, with an helmet and 3D mouse. By using specialised collision detection software, the computer can find optimal paths to lower each detector part into the pits and position it to destination, letting us visualize the whole assembly probess. During construction, these paths can be fed to a robot controller, which can operate the bridge cranes and build LHC almost without human intervention. VENUS is currently developing a multiplatform VR browser that will let the whole HEP community access LHC's Virtual Protoypes over the web. Many interesting things took place during the conference on Virtual Reality. For more information please refer to the Virtual Reality section.

  20. UA1 prototype detector

    CERN Multimedia

    1980-01-01

    Prototype of UA1 central detector inside a plexi tube. The UA1 experiment ran at CERN's Super Proton Synchrotron and made the Nobel Prize winning discovery of W and Z particles in 1983. The UA1 central detector was crucial to understanding the complex topology of proton-antiproton events. It played a most important role in identifying a handful of Ws and Zs among billions of collisions. The detector was essentially a wire chamber - a 6-chamber cylindrical assembly 5.8 m long and 2.3 m in diameter, the largest imaging drift chamber of its day. It recorded the tracks of charged particles curving in a 0.7 Tesla magnetic field, measuring their momentum, the sign of their electric charge and their rate of energy loss (dE/dx). Atoms in the argon-ethane gas mixture filling the chambers were ionised by the passage of charged particles. The electrons which were released drifted along an electric field shaped by field wires and were collected on sense wires. The geometrical arrangement of the 17000 field wires and 6...

  1. [Effects of Chinese prickly ash orchard on soil organic carbon mineralization and labile organic carbon in karst rocky desertification region of Guizhou province].

    Science.gov (United States)

    Zhang, Wen-Juan; Liao, Hong-Kai; Long, Jian; Li, Juan; Liu, Ling-Fei

    2015-03-01

    Taking 5-year-old Chinese prickly ash orchard (PO-5), 17-year-old Chinese prickly ash orchard (PO- 17), 30-year-old Chinese prickly ash orchard (PO-30) and the forest land (FL, about 60 years) in typical demonstration area of desertification control test in southwestern Guizhou as our research objects, the aim of this study using a batch incubation experiment was to research the mineralization characteristics of soil organic carbon and changes of the labile soil organic carbon contents at different depths (0-15 cm, 15-30 cm, and 30-50 cm). The results showed that: the cumulative mineralization amounts of soil organic carbon were in the order of 30-year-old Chinese prickly ash orchard, the forest land, 5-year-old Chinese prickly ash orchard and 17-year-old Chinese prickly ash orchard at corresponding depth. Distribution ratios of CO2-C cumulative mineralization amount to SOC contents were higher in Chinese prickly ash orchards than in forest land at each depth. Cultivation of Chinese prickly ash in long-term enhanced the mineralization of soil organic carbon, and decreased the stability of soil organic carbon. Readily oxidized carbon and particulate organic carbon in forest land soils were significantly more than those in Chinese prickly ash orchards at each depth (P < 0.05). With the increasing times of cultivation of Chinese prickly ash, the contents of readily oxidized carbon and particulate organic carbon first increased and then declined at 0-15 cm and 15-30 cm depth, respectively, but an opposite trend was found at 30-50 cm depth. At 0-15 cm and 15-30 cm, cultivation of Chinese prickly ash could be good for improving the contents of labile soil organic carbon in short term, but it was not conducive in long-term. In this study, we found that cultivation of Chinese prickly ash was beneficial for the accumulation of labile organic carbon at the 30-50 cm depth.

  2. Dry season supplementation of dairy cows with urea molasses mineral blocks and molasses-urea mix in the Morogoro region in Tanzania

    International Nuclear Information System (INIS)

    Plaizier, J.C.B.; McBride, B.W.; Nkya, R.; Shem, M.N.; Urio, N.A.

    1999-01-01

    The effects of supplementation with urea molasses mineral blocks and molasses-urea mix during and immediately prior to the dry season on the production of dairy cows were studied on-station and on small holder peri-urban farms near Morogoro, Tanzania. Supplementation of on-station cows receiving ad libitum grass hay and 6 kg/d of maize bran with urea molasses mineral blocks (UMMB), increased milk production from 6.7 L/d to 11.2 L/d (P <0.05) and dry matter intake from 10.1 kg/d to 12.0 kg/d (P <0.05), but did not significantly affect milk composition, intake of hay and live weight change. This increase in milk yield is mainly explained by increased intakes of energy and nitrogen. Supplementation with the molasses urea mix increased daily milk yield from 6.7 L/d to 8.8 L/d (P <0.05), but did not significantly affect the other measured production parameters. The on-farm supplementation with blocks increased daily milk yield by 1.7 L/d in the dry season (P <0.01). This supplementation did not increase milk yields prior to the dry season, since quality forage was still available. Taking the production costs into account, supplementation with the blocks and supplementation with molasses mix was cost effective if milk yields increased by 0.7 L/d. (author)

  3. Prototype moving-ring reactor

    International Nuclear Information System (INIS)

    Smith, A.C. Jr.; Ashworth, C.P.; Abreu, K.E.

    1981-01-01

    The objective of this work was to design a prototype fusion reactor based on fusion plasmas confined as ''Compact Toruses.' Six major criteria guided the prototype design. The prototype must: (1) produce net electricity decisively (P/sub net/ >70% of P/sub gross/), with P/sub net/ approximately 100 MW(e); (2) have small physical size (low project cost) but commercial plant; (3) have all features required of commerical plants; (4) avoid unreasonable extrapolation of technology; (5) minimize nuclear issues substantially, i.e. accident and waste issues of public concern, and (6) be modular (to permit repetitive fabrication of parts) and be maintainable with low occupational radiological exposures

  4. Regional evaluation and primary geological structural and metallogenical research of great Kavir basin as view of possibility formation of sedimentary-surficial Uranium mineralization

    International Nuclear Information System (INIS)

    Kamali Sadr, S.

    2006-01-01

    Great Kavir basin is the largest inner basin in Iran that extended about 90000 km 2. This basin is situated in the centre of lran , to the south from Alborz mountain range and elongated in the sub- latitudinal trend and its construction is asymmetric. The basin cover consists generally of complicated sequence of continental - marine Oligocene - Miocene molasses. According to drainage systems - conditions, molassoid cycles, alluvial, alluvial - deltaic and lacustrine sediments, climate, morphological conditions and metallogenic and structural features, Great Kavir depression generally is favorable for exigence and surficial uranium deposits (vally - fill, flood plain, deltaic and playa). Uranium occurrences that are Known in the southern and north eastern part of the margent Great Kavir basin, are Arosan, Irekan and Mohammad Abad. Similar geological - structural conditions for uranium mineralization is possible in the margent of Great Kavir basin

  5. Mineral parageneses, regional architecture, and tectonic evolution of Franciscan metagraywackes, Cape Mendocino-Garberville-Covelo 30' x 60' quadrangles, northwest California

    Science.gov (United States)

    Ernst, W.G.; McLaughlin, Robert J.

    2012-01-01

    The Franciscan Complex is a classic subduction-zone assemblage. In northwest California, it comprises a stack of west vergent thrust sheets: westernmost Eastern Belt outliers; Central Belt mélange; Coastal Belt Yager terrane; Coastal Belt Coastal terrane; Coastal Belt King Range/False Cape terranes. We collected samples and determined P-T conditions of recrystallization for 88 medium-fine-grained metasandstones to assess their subduction-exhumation histories and assembly of the host allochthons. Feebly recrystallized Yager, Coastal, and King Range strata retain clear detrital features. Scattered neoblastic prehnite occurs in several Coastal terrane metasandstones; traces of possible pumpellyite are present in three Yager metaclastic rocks. Pumpellyite ± lawsonite ± aragonite-bearing Central Belt metasandstones are moderately deformed and reconstituted. Intensely contorted, thoroughly recrystallized Eastern Belt affinity quartzose metagraywackes contain lawsonite + jadeitic pyroxene ± aragonite ± glaucophane. We microprobed neoblastic phases in 23 rocks, documenting mineral parageneses that constrain the tectonic accretion and metamorphic P-T evolution of these sheets. Quasi-stable mineral assemblages typify Eastern Belt metasandstones, but mm-sized domains in the Central and Coastal belt rocks failed to achieve chemical equilibrium. Eastern Belt slabs rose from subduction depths approaching 25–30 km, whereas structurally lower Central Belt mélanges returned from ∼15–18 km. Coastal Belt assemblages suggest burial depths less than 5–8 km. Eastern and Central belt allochthons sequentially decoupled from the downgoing oceanic lithosphere and ascended into the accretionary margin; K-feldspar-rich Coastal Belt rocks were stranded along the continental edge without undergoing appreciable subduction, probably during Paleogene unroofing of the older, deeply subducted units of the Franciscan Complex in east-vergent crustal wedges.

  6. Learning Axure RP interactive prototypes

    CERN Document Server

    Krahenbuhl, John Henry

    2015-01-01

    If you are a user experience professional, designer, information architect, or business analyst who wants to gain interactive prototyping skills with Axure, then this book is ideal for you. Some familiarity with Axure is preferred but not essential.

  7. Architectural Prototyping in Industrial Practice

    DEFF Research Database (Denmark)

    Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2008-01-01

    Architectural prototyping is the process of using executable code to investigate stakeholders’ software architecture concerns with respect to a system under development. Previous work has established this as a useful and cost-effective way of exploration and learning of the design space of a system......, in addressing issues regarding quality attributes, in addressing architectural risks, and in addressing the problem of knowledge transfer and conformance. Little work has been reported so far on the actual industrial use of architectural prototyping. In this paper, we report from an ethnographical study...... and focus group involving architects from four companies in which we have focused on architectural prototypes. Our findings conclude that architectural prototypes play an important role in resolving problems experimentally, but less so in exploring alternative solutions. Furthermore, architectural...

  8. Experimentation with PEC channel prototype

    International Nuclear Information System (INIS)

    Caponetti, R.; Iacovelli, M.

    1984-01-01

    Experimentation on prototypes of PEC components is presently being carried out at Casaccia CRE. This report shows the results of the first cycle of experimentation of the central channel, concerning the aspects of sodium removal after experimentation

  9. Tangiplay: prototyping tangible electronic games

    OpenAIRE

    Boileau, Jason

    2010-01-01

    Tangible electronic games currently exist in research laboratories around the world but have yet to transition to the commercial sector. The development process of a tangible electronic game is one of the factors preventing progression, as it requires much time and money. Prototyping tools for tangible hardware and software development are becoming more available but are targeted to programmers and technically trained developers. Paper prototyping board and video games is a proven and rapid m...

  10. Fast-prototyping of VLSI

    International Nuclear Information System (INIS)

    Saucier, G.; Read, E.

    1987-01-01

    Fast-prototyping will be a reality in the very near future if both straightforward design methods and fast manufacturing facilities are available. This book focuses, first, on the motivation for fast-prototyping. Economic aspects and market considerations are analysed by European and Japanese companies. In the second chapter, new design methods are identified, mainly for full custom circuits. Of course, silicon compilers play a key role and the introduction of artificial intelligence techniques sheds a new light on the subject. At present, fast-prototyping on gate arrays or on standard cells is the most conventional technique and the third chapter updates the state-of-the art in this area. The fourth chapter concentrates specifically on the e-beam direct-writing for submicron IC technologies. In the fifth chapter, a strategic point in fast-prototyping, namely the test problem is addressed. The design for testability and the interface to the test equipment are mandatory to fulfill the test requirement for fast-prototyping. Finally, the last chapter deals with the subject of education when many people complain about the lack of use of fast-prototyping in higher education for VLSI

  11. Prototyping the social

    DEFF Research Database (Denmark)

    Lindhardt Weiss, Kristoffer

    2017-01-01

    Adventures in Conceptualism explores the method of concept-based architecture through a series of conversations with some of the world's leading architects and urbanists. From offices such as Snøhetta, BIG, NL Architects and Danish HLA, the production of formal diversity shows an apparent devotio...... to a free and experimental practice, cutting across regional differences and stylistic modes. Every new project seems to conceptually reinvent the architectural language, responding to specific programmatic and contextual conditions....

  12. Laboratory of minerals purification

    International Nuclear Information System (INIS)

    2002-01-01

    The laboratory of minerals purification was organized in 1962 where with application of modern physical and chemical methods were investigated the mechanism of flotation reagents interaction with minerals' surface, was elaborated technologies on rising complexity of using of republic's minerals

  13. Developing IEC prototypes for adolescents. IEC workshop.

    Science.gov (United States)

    1997-01-01

    Participants of the IEC Workshop for the Production of OHP Material on Reproductive Health for Adolescents and Young Adults held November 25-30 in Japan developed innovative, visually appealing overhead projector (OHP) transparencies to serve as prototype information, education, and communication (IEC) materials for the Asian Region. The materials cover a wide range of topics from early marriage to unwanted pregnancy. This paper briefly describes the prototypes. One group focused upon early marriage, an issue of considerable importance to the health and welfare of young women in countries such as Bhutan, India, and Nepal. Participants from China, Laos, Malaysia, and Thailand focused upon the issue of gender equality, while a third group developed OHP material to teach a range of issues related to young people's sexual and reproductive health. Finally, the fourth group, drawn from Indonesia, the Philippines, and Vietnam, focused upon the topic of menstruation with a prototype targeted to boys and girls aged 9-14 years. Boys were included to foster their understanding of menstruation as a natural phenomenon.

  14. Prototypical versus contemporary Mediterranean Diet.

    Science.gov (United States)

    Rizza, W; De Gara, L; Antonelli Incalzi, R; Pedone, C

    2016-10-01

    To investigate the evolution of the Mediterranean Diet (MD) in a delimited area of Southern Italy, by comparing the diet adopted 60-70 years ago (Prototypical Mediterranean Diet, PMD) with the contemporary one (Contemporary Mediterranean Diet, CMD), and to verify to what extent they fitted the recommendations of the Italian and the USDA dietary guidelines. We recruited a total of 106 participants, divided in two groups. PMD group included 52 women aged >80 years, with a good cognitive function and full independence in basic and instrumental activities of daily living. CMD group included 20 men and 34 women aged 50-60 years. Food intake was assessed by administering the EPIC food frequency questionnaire to each participant, and an additional survey to the PMD subjects only. Both PMD and CMD showed adequate intakes of macronutrients, although some deficiencies related to micronutrient requirements were evident. CMD showed a slightly greater use of animal products, processed and sugary foods, and higher intakes of simple sugars, animal proteins (49.6 vs 28.3 g/day), animal lipids (37.8 vs 20.1 g/day), saturated fats (25.0 vs 15.8 g/day) and cholesterol (305.0 vs 258.5 g/day). PMD showed many similarities to the original version of the MD in terms of macronutrients distribution and food choices. The documented evolution of the dietary habits over a 70 years timespan suggests that nowadays Mediterranean regions adhere less strictly to the original MD, although nutrients intakes are adequate to LARN and USDA recommendations. Copyright © 2016 European Society for Clinical Nutrition and Metabolism. Published by Elsevier Ltd. All rights reserved.

  15. South Africa's mineral industry

    International Nuclear Information System (INIS)

    1985-06-01

    The main aim of the Minerals Bureau in presenting this annual review is to provide an up-to-date reference document on the current state of the mineral industry in South Africa. This includes a brief look at the production, trade, economy, resources and deposits of precious metals and minerals, energy minerals, metallic minerals, and non-metallic minerals. One article discusses the production, trade, export, deposits and economy of uranium

  16. The radioactivity of bottled mineral waters

    International Nuclear Information System (INIS)

    Vrakova, M.; Babarikova, F.; Belanova, A.

    2005-01-01

    Mineral waters with increased contents of minerals (total mineralization ranging from 1000 to 4000 mg.dm -3 ) can also contain increased concentrations of natural radionuclides. For this reason it is necessary to monitor radioactivity of mineral and thermal springs. Hundreds of springs which are used for drinking purposes are spread in many regions all over Slovakia. In our laboratory we determined these radionuclides in mineral waters: total alpha, total beta, volume activity 222 Rn, concentration of U nat , volume 226 Ra, 228 Ra and 210 Po. From values of determined volume activities of radionuclides we calculated total effective dose from reception mineral waters. By calculation of effective dose we supposed consumption of mineral water 150 dm 3 .year -1 (0.4 dm 3 .day -1 ) for adults (according to UNSCEAR). Conversion factors are initiated in the regulation of Ministry of Health of Slovak Republic (MZ SR No.12/2001). (authors)

  17. Evaluation of mandibular bone mineral density using the dual-energy X-ray absorptiometry technique in edentulous subjects living in an endemic fluorosis region.

    Science.gov (United States)

    Buyukkaplan, U S; Guldag, M U

    2012-07-01

    Fluoride is one of the biological trace elements with a strong affinity for osseous, cartilaginous and dental tissue. The dental and skeletal effects of high fluoride intake have already been studied in the literature, but little is known about the effects of high fluoride intake on edentulous mandibles. The purpose of this study was to evaluate the effects of high fluoride intake on mandibular bone mineral density (BMD) measured by the dual-energy X-ray absorptiometry (DXA) technique in edentulous individuals with systemic fluorosis. 32 people who were living in an endemic fluorosis area since birth and 31 people who were living in a non-endemic fluorosis area since birth (control group) participated in this study. Systemic fluorosis was diagnosed in the patients using the sialic acid (NANA)/glycosaminoglycan (GAG) ratio. The BMDs of the mandibles were determined by the DXA technique. The serum NANA/GAG ratios in the fluorosis group were significantly lower than those in the control group (p structures of the stomatognathic system.

  18. Fahlore and Sphalerite from the Darasun Gold Deposit in the Eastern Transbaikal Region, Russia: I. Mineral Assemblages and Intergrowths, Chemical Composition, and Its Evolution

    Science.gov (United States)

    Lyubimtseva, N. G.; Bortnikov, N. S.; Borisovsky, S. E.; Prokofiev, V. Yu.; Vikent'eva, O. V.

    2018-03-01

    The mineral assemblages, mode of occurrence, and chemical compositions of coexisting fahlore and sphalerite from the Darasun gold deposit have been described. Three generations of fahlore and three generations of sphalerite have been recognized. The FeS content in sphalerite coexisting with fahlore ranges from 0.8 to 9.4 mol %. The complete solid solution series Fe-tetrahedrite-Zn-tetrahedrite-Fe-tennantite-Zn-tennantite reflected in Sb/(Sb + As) and Fe/(Fe + Zn) ratios ranging from 0 to 0.97 and from 0.07 to 1.00, respectively, with a predominant negative relationship between these ratios has been identified for the first time at the deposit. Stepped, oscillatory, and combined stepped-oscillatory growth zonings within fahlore grains and heterogeneous aggregates of fahlore have been found. Fahlore is enriched in As with respect to Sb, and Zn-tetrahedrite is followed by Fe- and Zn-tennantite from early to late generation; Zn-tetrahedrite is followed by Fe-tennantite in zoned grains and overgrown rims; sphalerite crystallized at decreased temperature and sulfur fugacity. The evolution of the chemical composition of fahlores was caused by the evolving temperature, fluid salinity, and conditions of metal migration.

  19. Miscellaneous Industrial Mineral Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes miscellaneous industrial minerals operations in the United States. The data represent commodities covered by the Minerals Information Team...

  20. Prototype learning and dissociable categorization systems in Alzheimer's disease.

    Science.gov (United States)

    Heindel, William C; Festa, Elena K; Ott, Brian R; Landy, Kelly M; Salmon, David P

    2013-08-01

    Recent neuroimaging studies suggest that prototype learning may be mediated by at least two dissociable memory systems depending on the mode of acquisition, with A/Not-A prototype learning dependent upon a perceptual representation system located within posterior visual cortex and A/B prototype learning dependent upon a declarative memory system associated with medial temporal and frontal regions. The degree to which patients with Alzheimer's disease (AD) can acquire new categorical information may therefore critically depend upon the mode of acquisition. The present study examined A/Not-A and A/B prototype learning in AD patients using procedures that allowed direct comparison of learning across tasks. Despite impaired explicit recall of category features in all tasks, patients showed differential patterns of category acquisition across tasks. First, AD patients demonstrated impaired prototype induction along with intact exemplar classification under incidental A/Not-A conditions, suggesting that the loss of functional connectivity within visual cortical areas disrupted the integration processes supporting prototype induction within the perceptual representation system. Second, AD patients demonstrated intact prototype induction but impaired exemplar classification during A/B learning under observational conditions, suggesting that this form of prototype learning is dependent on a declarative memory system that is disrupted in AD. Third, the surprisingly intact classification of both prototypes and exemplars during A/B learning under trial-and-error feedback conditions suggests that AD patients shifted control from their deficient declarative memory system to a feedback-dependent procedural memory system when training conditions allowed. Taken together, these findings serve to not only increase our understanding of category learning in AD, but to also provide new insights into the ways in which different memory systems interact to support the acquisition of

  1. Neural basis of scientific innovation induced by heuristic prototype.

    Directory of Open Access Journals (Sweden)

    Junlong Luo

    Full Text Available A number of major inventions in history have been based on bionic imitation. Heuristics, by applying biological systems to the creation of artificial devices and machines, might be one of the most critical processes in scientific innovation. In particular, prototype heuristics propositions that innovation may engage automatic activation of a prototype such as a biological system to form novel associations between a prototype's function and problem-solving. We speculated that the cortical dissociation between the automatic activation and forming novel associations in innovation is critical point to heuristic creativity. In the present study, novel and old scientific innovations (NSI and OSI were selected as experimental materials in using learning-testing paradigm to explore the neural basis of scientific innovation induced by heuristic prototype. College students were required to resolve NSI problems (to which they did not know the answers and OSI problems (to which they knew the answers. From two fMRI experiments, our results showed that the subjects could resolve NSI when provided with heuristic prototypes. In Experiment 1, it was found that the lingual gyrus (LG; BA18 might be related to prototype heuristics in college students resolving NSI after learning a relative prototype. In Experiment 2, the LG (BA18 and precuneus (BA31 were significantly activated for NSI compared to OSI when college students learned all prototypes one day before the test. In addition, the mean beta-values of these brain regions of NSI were all correlated with the behavior accuracy of NSI. As our hypothesis indicated, the findings suggested that the LG might be involved in forming novel associations using heuristic information, while the precuneus might be involved in the automatic activation of heuristic prototype during scientific innovation.

  2. Neural basis of scientific innovation induced by heuristic prototype.

    Science.gov (United States)

    Luo, Junlong; Li, Wenfu; Qiu, Jiang; Wei, Dongtao; Liu, Yijun; Zhang, Qinlin

    2013-01-01

    A number of major inventions in history have been based on bionic imitation. Heuristics, by applying biological systems to the creation of artificial devices and machines, might be one of the most critical processes in scientific innovation. In particular, prototype heuristics propositions that innovation may engage automatic activation of a prototype such as a biological system to form novel associations between a prototype's function and problem-solving. We speculated that the cortical dissociation between the automatic activation and forming novel associations in innovation is critical point to heuristic creativity. In the present study, novel and old scientific innovations (NSI and OSI) were selected as experimental materials in using learning-testing paradigm to explore the neural basis of scientific innovation induced by heuristic prototype. College students were required to resolve NSI problems (to which they did not know the answers) and OSI problems (to which they knew the answers). From two fMRI experiments, our results showed that the subjects could resolve NSI when provided with heuristic prototypes. In Experiment 1, it was found that the lingual gyrus (LG; BA18) might be related to prototype heuristics in college students resolving NSI after learning a relative prototype. In Experiment 2, the LG (BA18) and precuneus (BA31) were significantly activated for NSI compared to OSI when college students learned all prototypes one day before the test. In addition, the mean beta-values of these brain regions of NSI were all correlated with the behavior accuracy of NSI. As our hypothesis indicated, the findings suggested that the LG might be involved in forming novel associations using heuristic information, while the precuneus might be involved in the automatic activation of heuristic prototype during scientific innovation.

  3. Minerals from Macedonia: XV. Sivec mineral assemble

    International Nuclear Information System (INIS)

    Boev, Blazho; Jovanovski, Gligor; Makreski, Petre; Bermanec, Vladimir

    2005-01-01

    The paper presents investigations carried out on the collected minerals from the Sivec deposit. It is situated in the vicinity of the town of Prilep, representing a rare occurrence of sugary white dolomite marbles. The application of suitable methods of exploitation of decorative-dimension stones makes possible to obtain large amounts of commercial blocks well known in the world. Despite the existence of dolomite marbles, a series of exotic minerals are typical in Sivec mineralization. Among them, the most significant are: calcite, fluorite, rutile, phlogopite, corundum, diaspore, almandine, kosmatite (clintonite or margarite), clinochlore, muscovite, quartz, pyrite, tourmaline and zoisite. An attempt to identify ten collected minerals using the FT IR spectroscopy is performed. The identification of the minerals was based on the comparison of the infrared spectra of our specimens with the corresponding literature data for the mineral species originating all over the world. The coloured pictures of all studied silicate minerals are presented as well. (Author)

  4. Water Quality Evaluation of PET Bottled Water by Mineral Balance in the Northeast Asian Region: A Case Study of South Korea.

    Science.gov (United States)

    Houri, Daisuke; Koo, Chung Mo

    2015-09-01

    The past few years have seen a demand for drinking water in contemporary society with a focus on safety and taste. Mineral water is now marketed as a popular commercial product and, partly due to health concerns, the production. For the study, a comparison was carried out of water samples from 9 types of polyethylene terephthalate (PET) bottled water sold in South Korea as well as from tap water in the cities of Seoul and Chuncheon. These were compared with samples of Japanese PET bottled water in order to determine shared commonalities and identify individual characteristics. To evaluate water quality objectively, we quantified the elements contained in the water samples. Samples were assessed not with the usual sensory evaluation but with the evaluation approach advocated by Hashimoto et al. which employs the Water Index of Taste and the Water Index of Health. The levels of water quality obtained were compared with the "Prerequisites for Tasty Water" and the "Standards for Tasty Water" devised for city water. The PET Bottled water varieties analyzed in this study-Seoksu, Icis, Bong Pyong, Soon Soo 100, Dong Won Saem Mul, GI JANG SOO and DIAMOND-showed the Water Index of Taste ≥ 2.0 and the Water Index of Health ≥ 5.2, which we classified as tasty/healthy water. SamDaSoo and NamiNeral can be classified as tasty water due to their values of the Water Index of Taste ≥ 2.0 and the Water Index of Health water studied here fulfills the "Water Index of Taste," "Water Index of Health," "Standard for Tasty Water" and "Prerequisites for Tasty Water" that Japanese people value for city water. We can conclude that bottled water which meets water quality requirements will be considered good-tasting by a majority of people.

  5. The experimental results and analysis of a borehole radar prototype

    International Nuclear Information System (INIS)

    Liu, Sixin; Wu, Junjun; Dong, Hang; Fu, Lei; Wang, Fei

    2012-01-01

    A prototype of borehole radar has been successfully tested in three sites for different purposes under a field condition. The objective of the prototype is providing an effective down-hole tool for detecting targets in deep boreholes situated in a relatively high conductivity area such as the metal ores. The first testing site is at a geothermal field. The fractures extending more than 20 m from the borehole are delineated by the borehole radar in the single-hole reflection mode. The second testing site is located in a jade mine for basement evaluation. The cross-hole measurement mode was used to detect the cavities made by previous unorganized mining activities. Several high-velocity anomalies were found in the velocity profile and presumably the targets of the mine shafts and tunnels. The third test site is located in a mineralized belt characterized by low resistivity less than 1000 Ohm m, the surface-borehole measurement was carried out and the data were processed with velocity tomography. The low-velocity zone corresponds to a mineralized zone from geological records. The three testing results proved the readiness of this borehole radar prototype for further deployment in more complicated and realistic field situations. (paper)

  6. Prototypes in engineering design: Definitions and strategies

    DEFF Research Database (Denmark)

    Jensen, Lasse Skovgaard; Özkil, Ali Gürcan; Mortensen, Niels Henrik

    2016-01-01

    By reviewing literature, we investigate types, purposes and definitions of prototypes. There is no overarching definition of a prototype, but we identify five categories of prototypes in litterature. We further synthesize and reference previous work to create an overview of aspects in prototyping...

  7. Prototyping in theory and in practice

    DEFF Research Database (Denmark)

    Yu, Fei; Brem, Alexander; Pasinell, Michele

    2018-01-01

    and functions of a prototype and needed to meet specific goals in order to push the process forward. Designers, on the other hand, used prototypes to investigate the design space for new possibilities, and were more open to a variety of prototyping materials and tools, especially for low-fidelity prototypes...

  8. Rapid Prototyping of Formally Modelled Distributed Systems

    OpenAIRE

    Buchs, Didier; Buffo, Mathieu; Titsworth, Frances M.

    1999-01-01

    This paper presents various kinds of prototypes, used in the prototyping of formally modelled distributed systems. It presents the notions of prototyping techniques and prototype evolution, and shows how to relate them to the software life-cycle. It is illustrated through the use of the formal modelling language for distributed systems CO-OPN/2.

  9. Towards an Operational Framework for Architectural Prototyping

    DEFF Research Database (Denmark)

    Christensen, Henrik Bærbak

    2005-01-01

    We use a case study in architectural prototyping as input for presenting a first, tentative, framework describing key concepts and their relationships in architectural prototyping processes.......We use a case study in architectural prototyping as input for presenting a first, tentative, framework describing key concepts and their relationships in architectural prototyping processes....

  10. Composição mineral de uma linhagem de Pleurotus ostreatus cultivada em resíduos madeireiros e agroindustriais da região amazônica Mineral composition of Pleurotus ostreatus strain grown in wood and agroindustrial residues from the Amazon region

    Directory of Open Access Journals (Sweden)

    Ceci Sales-Campos

    2009-12-01

    Full Text Available Os cogumelos do gênero Pleurotus são cultivados em diversos substratos lignocelulósicos, dada a atividade decompositora desses organismos proveniente de seu metabolismo enzimático. O presente estudo teve como objetivo analisar a composição mineral de Pleurotus ostreatus e dos substratos de cultivo preparados à base de resíduos madeireiros e agroindustriais da região amazônica. Foram analisados macro (P, K, Ca e Mg e micronutrientes (Fe, Zn, Cu, Mn e Na dos cogumelos e dos substratos. Os substratos foram formulados a partir da serragem de Simarouba amara Aubl. (marupá, Ochroma piramidale Cav. ex. Lam. (pau de balsa e de bagaços de Bactris gasipaes Kunth (pupunheira e de Saccharum officinarum (cana-de-açúcar. As amostras foram solubilizadas mediante digestão ácida (nítrico-peridrol. Os elementos Ca, Mg, Fe, Cu, Zn e Mn foram determinados por espectrometria de absorção atômica; o Na e K, por emissão atômica e o P, por colorimetria. A composição mineral do cogumelo variou com o substrato de cultivo. Os diferentes substratos possibilitaram a produção de um cogumelo rico em K, P, Mg e Fe, essenciais à nutrição e à saúde humana. O potássio foi o mineral de maior teor no cogumelo em todos os substratos testados (36,83-42,18 g.kg-1, seguido de fósforo (6,95-10,60 g.kg-1 e do magnésio (1,57-2,50 g.kg-1.Mushrooms belonging to the Pleurotus gender are grown in several lignocellulosic substrates due to the decomposing activity of these organisms that result from their enzymatic metabolism. The objective of the present study was to analyze the mineral composition of Pleurotus ostreatus and the cultivation substrates prepared with wood and agroindustrial residues from the Amazon region. Macro (P, K, Ca and Mg and micronutrients (Fe, Zn, Cu, Mn and Na of mushroom and substrates were analyzed. Substrates were formulated from Simarouba amara Aubl. and Ochroma piramidale Cav. ex. Lam. sawdust and crushed Bactris gasipaes Kunth

  11. Engineering prototypes for theta-pinch devices

    International Nuclear Information System (INIS)

    Hansborough, L.D.; Hammer, C.F.; Hanks, K.W.; McDonald, T.E.; Nunnally, W.C.

    1975-01-01

    Past, present, and future engineering prototypes for theta-pinch plasma-physics devices at Los Alamos Scientific Laboratory are discussed. Engineering prototypes are designed to test and evaluate all components under system conditions expected on actual plasma-physics experimental devices. The importance of engineering prototype development increases as the size and complexity of the plasma-physics device increases. Past experiences with the Scyllac prototype and the Staged Theta-Pinch prototype are discussed and evaluated. The design of the proposed Staged Scyllac prototype and the Large Staged Scyllac implosion prototype assembly are discussed

  12. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase III of the Prototypical Rod Consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod Consolidation System as described in the NUS Phase II Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase III effort the system was tested on a component, subsystem, and system level. Volume IV provides the Operating and Maintenance Manual for the Prototypical Rod Consolidation System that was installed at the Cold Test Facility. This document, Book 1 of Volume IV, discusses: Process overview functional descriptions; Control system descriptions; Support system descriptions; Maintenance system descriptions; and Process equipment descriptions

  13. Science with the ASTRI prototype

    International Nuclear Information System (INIS)

    Sartore, Nicola

    2013-01-01

    ASTRI (Astrofisica a Specchi con Tecnologia Replicante Italiana) is a “Flagship Project” financed by the Italian Ministry of Instruction, University and Research and led by the Italian National Institute of Astrophysics. It represents the Italian proposal for the development of the Small Size Telescope system of the Cherenkov Telescope Array, the next generation observatory for Very High Energy gamma-rays (20 GeV - 100 TeV). The ASTRI end-to-end prototype will be installed at Serra La Nave (Catania, Italy) and it will see the first light at the beginning of 2014. We describe the expected performance of the prototype on few selected test cases of the northern emisphere. The aim of the prototype is to probe the technological solutions and the nominal performance of the various telescope's subsystems

  14. Flight Telerobotic Servicer prototype simulator

    Science.gov (United States)

    Schein, Rob; Krauze, Linda; Hartley, Craig; Dickenson, Alan; Lavecchia, Tom; Working, Bob

    A prototype simulator for the Flight Telerobotic Servicer (FTS) system is described for use in the design development of the FTS, emphasizing the hand controller and user interface. The simulator utilizes a graphics workstation based on rapid prototyping tools for systems analyses of the use of the user interface and the hand controller. Kinematic modeling, manipulator-control algorithms, and communications programs are contained in the software for the simulator. The hardwired FTS panels and operator interface for use on the STS Orbiter are represented graphically, and the simulated controls function as the final FTS system configuration does. The robotic arm moves based on the user hand-controller interface, and the joint angles and other data are given on the prototype of the user interface. This graphics simulation tool provides the means for familiarizing crewmembers with the FTS system operation, displays, and controls.

  15. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase III of the Prototypical Rod Consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod Consolidation System as described in the NUS Phase II Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase III effort the system was tested on a component, subsystem, and system level. Volume IV provides the Operating and Maintenance Manual for the Prototypical Rod Consolidation System that was installed at the Cold Test Facility. This document, Book 4 of Volume IV, discusses: Off-normal operating and recovery procedures; Emergency response procedures; Troubleshooting procedures; and Preventive maintenance procedures

  16. Efficacy study of the consumption of milk fortified in vitamins and minerals on the nutritional and cognitive status of children in rural regions of Morocco

    International Nuclear Information System (INIS)

    El Manchawy, Imane; Baymou, El Mehdi; Amjed, Achour; Benjeddou, Kaoutar; El Haloui, Noureddine; Aguenaou, Hassan; Badahi, Ahmed; Rjimati, El Arbi

    2014-01-01

    the vitamins and minerals status of children. A study of longer duration should be conducted to determine the improvement of the cognitive capacities. The results of this investigation will be useful to the National Nutrition Strategy, 2011-2019 especially as they pertain to the food fortification component. This study was performed with the support of “La Fondation Centrale Laitière de Nutrition pour l'Enfant”. (author)

  17. Axure RP 6 Prototyping Essentials

    CERN Document Server

    Schwartz, Ezra

    2012-01-01

    Axure RP 6 Prototyping Essentials is a detailed, practical primer on the leading rapid prototyping tool. Short on jargon and high on concepts, real-life scenarios and step-by-step guidance through hands-on examples, this book will show you how to integrate Axure into your UX workflow. This book is written for UX practitioners, business analysts, product managers, and anyone else who is involved in UX projects. The book assumes that you have no or very little familiarity with Axure. It will help you if you are evaluating the tool for an upcoming project or are required to quickly get up to spee

  18. Evaluation of mineral resource potential of the Finnish precambrian

    International Nuclear Information System (INIS)

    Peltonen, K.

    1993-05-01

    In the report the undiscovered mineral resource potential of metallogenic regions in Finland is evaluated. The evaluation is based on known deposits. The criteria of the evaluation were: ore and mineral deposit density, regional distribution of valuable metals, and the amount and the nature of prospecting methods used. The information for the study has been collected from the data base for ore minerals maintained by the Geological Survey of Finland. Regions with mineral resource potential conclusively under national average are Presvecokarelidic and Svecokarelidic granitoids and rapakivi Massif. The mineral resource potential of basic rocks in relation to their surface area is multiple compared to non-basic rocks

  19. Nuclear minerals in Pakistan

    International Nuclear Information System (INIS)

    Mansoor, M.

    2005-01-01

    Strategic importance of Nuclear Minerals was recognized during early formative years of the Pakistan Atomic Energy Commission, and prospecting for uranium was started in Dera Ghazi Khan in collaboration with the Geological Survey of Pakistan (GSP) as early as 1961. Later, the responsibility for countrywide surveys and exploration was fully entrusted with PAEC and in this respect a Directorate of Nuclear Minerals(DNM) was established in 1966 at Lahore. Later, DNM was shifted to the Atomic Energy Centre (AEC), Lahore building and renamed as Atomic Energy Minerals Centre. It has state-of-the-art Chemistry, Mineralogy, Remote Sensing and Electronics Laboratories and an Ore Processing Pilot Plant. The Centre has Prospecting, Exploration, Geophysics, Geochemistry, Geo-tectonics, Mining and Drilling Sections. Regional Offices have been established to facilitate work at Karachi, Quetta and Peshawar. Siwaliks were recognized as a favorable geological formation of prime importance. Sandstone-shale sequence of Siwaliks Formation is exposed in all provinces of Pakistan and in Azad Jammu and Kashmir (AJK), broadly categorized into Rajanpur-Dera Ghazi Khan, Bannu Basin-Kohat Plateau and Potwar-AJK zones. Baghalchur, Nangar Nai and Taunsa uranium deposits have been discovered in the Rajanpur- D.G. Khan Zone. Qabul Khel and Shanawah Uranium deposits have been discovered in the Shanawah-Kohat Plateau Zone. Prospection and exploration is in progress. The first uranium mine was opened at Baghalchur, and uranium mill was established at D.G Khan in 1977-78 all by indigenous effort. The uranium mine was the most advanced and mechanized mine of that time in the country. Later, a second uranium mine was opened at Qabul Khel in 1992, which was based on a new and advanced in situ leach technology, developed to suit local geological and ore zone parameters. Mining of Nanganai and Taunsa Deposits was started respectively in 1996 and 2002, and is also based on in situ leach technology which is

  20. NMS Prototype development final report

    International Nuclear Information System (INIS)

    Lepetich, J.E.

    1993-01-01

    Program for development of NMS prototype for LAMPF consisted of 5 tasks: crystal procurement specification, inspection/evaluation of CsI crystals, design/fabrication of crystal housing, design/fabrication of PMT shields, and packaging of crystals in the housing

  1. EUSO-TA prototype telescope

    Energy Technology Data Exchange (ETDEWEB)

    Bisconti, Francesca, E-mail: francesca.bisconti@kit.edu

    2016-07-11

    EUSO-TA is one of the prototypes developed for the JEM-EUSO project, a space-based large field-of-view telescope to observe the fluorescence light emitted by cosmic ray air showers in the atmosphere. EUSO-TA is a ground-based prototype located at the Telescope Array (TA) site in Utah, USA, where an Electron Light Source and a Central Laser Facility are installed. The purpose of the EUSO-TA project is to calibrate the prototype with the TA fluorescence detector in presence of well-known light sources and cosmic ray air showers. In 2015, the detector started the first measurements and tests using the mentioned light sources have been performed successfully. A first cosmic ray candidate has been observed, as well as stars of different magnitude and color index. Since Silicon Photo-Multipliers (SiPMs) are very promising for fluorescence telescopes of next generation, they are under consideration for the realization of a new prototype of EUSO Photo Detector Module (PDM). The response of this sensor type is under investigation through simulations and laboratory experimentation.

  2. The OPAL vertex detector prototype

    International Nuclear Information System (INIS)

    Roney, J.M.; Armitage, J.C.; Carnegie, R.K.; Giles, G.L.; Hemingway, R.J.; McPherson, A.C.; Pinfold, J.L.; Waterhouse, J.; Godfrey, L.; Hargrove, C.K.

    1989-01-01

    The prototype test results of a high resolution charged particle tracking detector are reported. The detector is designed to measure vertex topologies of particles produced in the e + e - collisions of the OPAL experiment at LEP. The OPAL vertex detector is a 1 m long, 0.46 m diameter cylindrical drift chamber consisting of an axial and stereo layer each of which is divided into 36 jet cells. A prototype chamber containing four axial and two stereo cells was studied using a pion test beam at CERN. The studies examined the prototype under a variety of operating conditions. An r-Φ resolution of 60 μm was obtained when the chamber was operated with argon (50%)-ethane (50%) at 3.75 bar, and when CO 2 (80%)-isobutane (20%) at 2.5 bar was used a 25 μm resolution was achieved. A z measurement using end-to-end time difference has a resolution of 3.5 cm. The details of these prototype studies are discussed in this paper. (orig.)

  3. Rapid Prototyping Enters Mainstream Manufacturing.

    Science.gov (United States)

    Winek, Gary

    1996-01-01

    Explains rapid prototyping, a process that uses computer-assisted design files to create a three-dimensional object automatically, speeding the industrial design process. Five commercially available systems and two emerging types--the 3-D printing process and repetitive masking and depositing--are described. (SK)

  4. Encapsulation of polymer photovoltaic prototypes

    DEFF Research Database (Denmark)

    Krebs, Frederik C

    2006-01-01

    A simple and efficient method for the encapsulation of polymer and organic photovoltaic prototypes is presented. The method employs device preparation on glass substrates with subsequent sealing using glass fiber reinforced thermosetting epoxy (prepreg) against a back plate. The method allows...

  5. EUSO-TA prototype telescope

    Science.gov (United States)

    Bisconti, Francesca; JEM-EUSO Collaboration

    2016-07-01

    EUSO-TA is one of the prototypes developed for the JEM-EUSO project, a space-based large field-of-view telescope to observe the fluorescence light emitted by cosmic ray air showers in the atmosphere. EUSO-TA is a ground-based prototype located at the Telescope Array (TA) site in Utah, USA, where an Electron Light Source and a Central Laser Facility are installed. The purpose of the EUSO-TA project is to calibrate the prototype with the TA fluorescence detector in presence of well-known light sources and cosmic ray air showers. In 2015, the detector started the first measurements and tests using the mentioned light sources have been performed successfully. A first cosmic ray candidate has been observed, as well as stars of different magnitude and color index. Since Silicon Photo-Multipliers (SiPMs) are very promising for fluorescence telescopes of next generation, they are under consideration for the realization of a new prototype of EUSO Photo Detector Module (PDM). The response of this sensor type is under investigation through simulations and laboratory experimentation.

  6. Facial Prototype Formation in Children.

    Science.gov (United States)

    Inn, Donald; And Others

    This study examined memory representation as it is exhibited in young children's formation of facial prototypes. In the first part of the study, researchers constructed images of faces using an Identikit that provided the features of hair, eyes, mouth, nose, and chin. Images were varied systematically. A series of these images, called exemplar…

  7. Calagem e adubação mineral e orgânica do cafeeiro na região de Campinas Liming and mineral and organic fertilization of coffee tree at Campinas Region, State of São Paulo, Brazil

    Directory of Open Access Journals (Sweden)

    Genésio da Silva Cervellini

    1994-01-01

    Full Text Available Instalou-se um experimento com cafeeiro cultivar Mundo Novo LCP 387-17 em um latossolo roxo transição para latossolo vermelho-amarelo orto, cuja vegetação original era típica de cerrado, na região de Campinas, comparando-se os tratamentos com esterco de curral e adubação mineral NPK, complementados ou não com calcário dolomítico e com os micronutrientes zinco e boro. Aplicaram-se, por ano e por cova, 40 litros de esterco quando na ausência de NPK e 20 litros quando com NPK. A adubação mineral constou da utilização de 120 g de N, 40 g de P2O5 e 120 g de K2O por ano e por cova; quando em presença de esterco, usou-se metade dessas doses. O calcário foi aplicado na quantidade de 1 kg por ano e por cova, e zinco e boro, na quantidade de 20 g de sulfato de zinco e 20 g de bórax, também por cova e por ano. A análise das produções de café beneficiado no período de 1965 a 1970 permitiu constatar que a testemunha e o tratamento com NPK foram significativamente inferiores aos demais. Destacaram-se com as melhores produções os tratamentos que receberam esterco mais NPK, com ou sem calcário. Nas análises de solos, constatou-se aumento nas bases quando foi aplicado o esterco e, em contrapartida, aumento de acidez com o tratamento de NPK. As análises das folhas mostraram efeitos sobre teores de alumínio e manganês coerentes com os dados obtidos nas produções e análises do solo.Experiments with mineral and organic manure were carried out in a Red Latosolic Soil Transition to Orto Red Yellow Latosolic Soil at Campinas region with Mundo Novo LCP 387-17 coffee tree cultivar. The treatments with manure was compared with the treatments with mineral fertilizers of NPK with or without lime or micronutrients zinc and boron. The analyses of coffee production data showed that the treatments with mineral fertilizers and the test treatment with no fertilizer, had the lowest productions. The treatments with manure and NPK with or without

  8. Oxyvanite, V3O5, a new mineral species and the oxyvanite-berdesinskiite V2TiO5 series from metamorphic rocks of the Slyudyanka Complex, southern Baikal region

    Science.gov (United States)

    Reznitsky, L. Z.; Sklyarov, E. V.; Armbruster, T.; Ushchapovskaya, Z. F.; Galuskin, E. V.; Polekhovsky, Yu. S.; Barash, I. G.

    2010-12-01

    Oxyvanite has been identified as an accessory mineral in Cr-V-bearing quartz-diopside meta- morphic rocks of the Slyudyanka Complex in the southern Baikal region, Russia. The new mineral was named after constituents of its ideal formula (oxygen and vanadium). Quartz, Cr-V-bearing tremolite and micas, calcite, clinopyroxenes of the diopside-kosmochlor-natalyite series, Cr-bearing goldmanite, eskolaite-karelianite dravite-vanadiumdravite, V-bearing titanite, ilmenite, and rutile, berdesinskiite, schreyerite, plagioclase, scapolite, barite, zircon, and unnamed U-Ti-V-Cr phases are associated minerals. Oxyvanite occurs as anhedral grains up to 0.1-0.15 mm in size, without visible cleavage and parting. The new mineral is brittle, with conchoidal fracture. Observed by the naked eye, the mineral is black, with black streak and resinous luster. The microhardness (VHN) is 1064-1266 kg/mm2 (load 30 g), and the mean value is 1180 kg/mm2. The Mohs hardness is about 7.0-7.5. The calculated density is 4.66(2) g/cm3. The color of oxyvanite is pale cream in reflected light, without internal reflections. The measured reflectance in air is as follows (λ, nm- R, %): 440-17.8; 460-18; 480-18.2; 520-18.6; 520-18.6; 540-18.8; 560-18.9; 580-19; 600-19.1; 620-19.2; 640-19.3; 660-19.4; 680-19.5; 700-19.7. Oxyvanite is monoclinic, space group C2/ c; the unit-cell dimensions are a = 10.03(2), b = 5.050(1), c = 7.000(1) Å, β = 111.14(1)°, V = 330.76(5)Å3, Z = 4. The strongest reflections in the X-ray powder pattern [ d, Å, ( I in 5-number scale)( hkl)] are 3.28 (5) (20 bar 2 ); 2.88 (5) (11 bar 2 ); 2.65, (5) (310); 2.44 (5) (112); 1.717 (5) (42 bar 2 ); 1.633 (5) (31 bar 4 ); 1.446 (4) (33 bar 2 ); 1.379 (5) (422). The chemical composition (electron microprobe, average of six point analyses, wt %): 14.04 TiO2, 73.13 V2O3 (53.97 V2O3calc, 21.25 VO2calc), 10.76 Cr2O3, 0.04 Fe2O3, 0.01 Al2O3, 0.02 MgO, total is 100.03. The empirical formula is (V{1.70/3+} Cr0.30)2.0(V{0.59/4+} Ti0.41)1.0O

  9. Prototype diagnosis of psychiatric syndromes

    Science.gov (United States)

    WESTEN, DREW

    2012-01-01

    The method of diagnosing patients used since the early 1980s in psychiatry, which involves evaluating each of several hundred symptoms for their presence or absence and then applying idiosyncratic rules for combining them for each of several hundred disorders, has led to great advances in research over the last 30 years. However, its problems have become increasingly apparent, particularly for clinical practice. An alternative approach, designed to maximize clinical utility, is prototype matching. Instead of counting symptoms of a disorder and determining whether they cross an arbitrary cutoff, the task of the diagnostician is to gauge the extent to which a patient’s clinical presentation matches a paragraph-length description of the disorder using a simple 5-point scale, from 1 (“little or no match”) to 5 (“very good match”). The result is both a dimensional diagnosis that captures the extent to which the patient “has” the disorder and a categorical diagnosis, with ratings of 4 and 5 corresponding to presence of the disorder and a rating of 3 indicating “subthreshold” or “clinically significant features”. The disorders and criteria woven into the prototypes can be identified empirically, so that the prototypes are both scientifically grounded and clinically useful. Prototype diagnosis has a number of advantages: it better captures the way humans naturally classify novel and complex stimuli; is clinically helpful, reliable, and easy to use in everyday practice; facilitates both dimensional and categorical diagnosis and dramatically reduces the number of categories required for classification; allows for clinically richer, empirically derived, and culturally relevant classification; reduces the gap between research criteria and clinical knowledge, by allowing clinicians in training to learn a small set of standardized prototypes and to develop richer mental representations of the disorders over time through clinical experience; and can help

  10. Prototype Effect and the Persuasiveness of Generalizations.

    Science.gov (United States)

    Dahlman, Christian; Sarwar, Farhan; Bååth, Rasmus; Wahlberg, Lena; Sikström, Sverker

    An argument that makes use of a generalization activates the prototype for the category used in the generalization. We conducted two experiments that investigated how the activation of the prototype affects the persuasiveness of the argument. The results of the experiments suggest that the features of the prototype overshadow and partly overwrite the actual facts of the case. The case is, to some extent, judged as if it had the features of the prototype instead of the features it actually has. This prototype effect increases the persuasiveness of the argument in situations where the audience finds the judgment more warranted for the prototype than for the actual case (positive prototype effect), but decreases persuasiveness in situations where the audience finds the judgment less warranted for the prototype than for the actual case (negative prototype effect).

  11. Supporting Active User Involvment in Prototyping

    DEFF Research Database (Denmark)

    Grønbæk, Kaj

    1990-01-01

    The term prototyping has in recent years become a buzzword in both research and practice of system design due to a number of claimed advantages of prototyping techniques over traditional specification techniques. In particular it is often stated that prototyping facilitates the users' involvement...... in the development process. But prototyping does not automatically imply active user involvement! Thus a cooperative prototyping approach aiming at involving users actively and creatively in system design is proposed in this paper. The key point of the approach is to involve users in activities that closely couple...... development of prototypes to early evaluation of prototypes in envisioned use situations. Having users involved in such activities creates new requirements for tool support. Tools that support direct manipulation of prototypes and simulation of behaviour have shown promise for cooperative prototyping...

  12. Prototyping of user interfaces for mobile applications

    CERN Document Server

    Bähr, Benjamin

    2017-01-01

    This book investigates processes for the prototyping of user interfaces for mobile apps, and describes the development of new concepts and tools that can improve the prototype driven app development in the early stages. It presents the development and evaluation of a new requirements catalogue for prototyping mobile app tools that identifies the most important criteria such tools should meet at different prototype-development stages. This catalogue is not just a good point of orientation for designing new prototyping approaches, but also provides a set of metrics for a comparing the performance of alternative prototyping tools. In addition, the book discusses the development of Blended Prototyping, a new approach for prototyping user interfaces for mobile applications in the early and middle development stages, and presents the results of an evaluation of its performance, showing that it provides a tool for teamwork-oriented, creative prototyping of mobile apps in the early design stages.

  13. Measurement of bone mineral density in the tunnel regions for anterior cruciate ligament reconstruction by dual-energy X-ray absorptiometry, computed tomography scan, and the immersion technique based on Archimedes' principle.

    Science.gov (United States)

    Tie, Kai; Wang, Hua; Wang, Xin; Chen, Liaobin

    2012-10-01

    To determine, for anterior cruciate ligament (ACL) reconstruction, whether the bone mineral density (BMD) of the femoral tunnel was higher than that of the tibial tunnel, to provide objective evidence for choosing the appropriate diameter of interference screws. Two groups were enrolled. One group comprised 30 normal volunteers, and the other comprised 9 patients with ACL rupture. Dual-energy X-ray absorptiometry was used to measure the BMD of the femoral and tibial tunnel regions of the volunteers' right knees by choosing a circular area covering the screw fixation region. The knees were also scanned by spiral computed tomography (CT), and the 3-dimensional reconstruction technique was used to determine the circular sections passing through the longitudinal axis of the femoral and tibial tunnels. Grayscale CT values of the cross-sectional area were measured. Cylindrical cancellous bone blocks were removed from the femoral and tibial tunnels during the ACL reconstruction for the patients. The volumetric BMD of the bone blocks was measured using a standardized immersion technique according to Archimedes' principle. As measured by dual-energy X-ray absorptiometry, the BMD of the femoral and tibial tunnel regions was 1.162 ± 0.034 g/cm(2) and 0.814 ± 0.038 g/cm(2), respectively (P difference in both femoral and tibial tunnel regions. For ACL reconstruction, the BMD of the femoral tunnel is higher than that of the tibial tunnel. This implies that a proportionally larger-diameter interference screw should be used for fixation in the proximal tibia than that used for fixation in the distal femur. Level IV, therapeutic case series. Copyright © 2012 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

  14. Design in action: From prototyping by demonstration to cooperative prototyping

    DEFF Research Database (Denmark)

    Bødker, Susanne; Grønbæk, Kaj

    1991-01-01

    ... the development of any computer-based system will have to proceed in a cycle from design to experience and back again. It is impossible to anticipate all of the relevant breakdown and their domains. They emerge gradually in practice. Winograd and Flores, 1986. p.171 Some time ago we worked wi...... with a group of dental assistants, designing a prototype case record system to explore the possibility of using computer support in public dental clinics. ...

  15. Mineral matter reactions in cokes

    Energy Technology Data Exchange (ETDEWEB)

    D. French; R. Sakurovs; M. Grigore [CSIRO Energy Technology (Australia)

    2009-07-15

    Some cokes appear to be particularly susceptible to weakening in the blast furnace. A mechanism which has been postulated to explain this is silica reduction by coke. Thus this project was initiated to ascertain the behaviour of quartz and silicates in coke with an emphasis on the role of the clay minerals. It is now possible to obtain quantitative mineralogical data and, the case of coal, to also obtain quantitative data on mineral grain size, shape and association through the use of automated electron beam image analysis techniques. This new ability can allow relationships between the amount of minerals in a coke and its reactivity to be established for the first time. Samples of five Australian coking coals were selected based upon quartz and clay mineral contents, mineral grain size and association. Samples were also provided by BlueScope Steel of coal, feed coke, and tuyere coke samples from the bosh, deadman and raceway regions of the blast furnace. The analytical work program conducted was as follows: Preparation of cokes by CSIRO; Petrography of starting coals and cokes; QEMSCAN of coals; LTA and XRD of starting coals and cokes; Coke reactivity tests (NSC and small scale); Petrography, LTA and XRD of reacted cokes; Petrographic and XRD examination of heat treated cokes. This study indicates that the NSC reactivity test does not adequately reflect the behaviour of coke in the lower part of the blast furnace. Further investigation of the behaviour of coke in the lower part of the blast furnace is required.

  16. Construction Minerals Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes construction minerals operations in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  17. Agricultural Minerals Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes agricultural minerals operations in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  18. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 2 discusses the following topics: Fuel Rod Extraction System Test Results and Analysis Reports and Clamping Table Test Results and Analysis Reports

  19. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 1 discusses the following topics: the background of the project; test program description; summary of tests and test results; problem evaluation; functional requirements confirmation; recommendations; and completed test documentation for tests performed in Phase 3

  20. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 9 discusses the following topics: Integrated System Normal Operations Test Results and Analysis Report; Integrated System Off-Normal Operations Test Results and Analysis Report; and Integrated System Maintenance Operations Test Results and Analysis Report

  1. Prototype of sun projector device

    Science.gov (United States)

    Ihsan; Dermawan, B.

    2016-11-01

    One way to introduce astronomy to public, including students, can be handled by solar observation. The widely held device for this purpose is coelostat and heliostat. Besides using filter attached to a device such as telescope, it is safest to use indirect way for observing the Sun. The main principle of the indirect way is deflecting the sun light and projecting image of the sun on a screen. We design and build a simple and low-cost astronomical device, serving as a supplement to increase public service, especially for solar observation. Without using any digital and intricate supporting equipment, people can watch and relish image of the Sun in comfortable condition, i.e. in a sheltered or shady place. Here we describe a design and features of our prototype of the device, which still, of course, has some limitations. In the future, this prototype can be improved for more efficient and useful applications.

  2. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 8 discusses Control System SOT Tests Results and Analysis Report. This is a continuation of Book 7

  3. Prototype and proposed ISABELLE dipoles

    International Nuclear Information System (INIS)

    McInturff, A.D.; Sampson, W.B.; Robins, K.E.; Dahl, P.F.; Damm, R.

    1977-01-01

    Data are presented on the latest dipole prototypes to update the operational parameters possible for ISABELLE. This data base will constantly expand until the start of construction of the storage rings. The data will include field quality, stray field magnitudes, quench temperature and propagation times, protection capabilities singly and in multiple units, maximum central fields obtained and training behavior. Performance of the dipoles versus temperature and mode of refrigeration will be discussed. The single layer cosine theta turns distribution coils' parameters are better than those required for the operation of the 200 x 200 GeV version of ISABELLE. The double layer prototype has exceeded the magnetic field performance and two dimensional quality of field needed for the 400 x 400 GeV version of ISABELLE

  4. Prototypical Rod Construction Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 3 discusses the following topics: Downender Test Results and Analysis Report; NFBC Canister Upender Test Results and Analysis Report; Fuel Assembly Handling Fixture Test Results and Analysis Report; and Fuel Canister Upender Test Results and Analysis Report

  5. Rapid mask prototyping for microfluidics.

    Science.gov (United States)

    Maisonneuve, B G C; Honegger, T; Cordeiro, J; Lecarme, O; Thiry, T; Fuard, D; Berton, K; Picard, E; Zelsmann, M; Peyrade, D

    2016-03-01

    With the rise of microfluidics for the past decade, there has come an ever more pressing need for a low-cost and rapid prototyping technology, especially for research and education purposes. In this article, we report a rapid prototyping process of chromed masks for various microfluidic applications. The process takes place out of a clean room, uses a commercially available video-projector, and can be completed in less than half an hour. We quantify the ranges of fields of view and of resolutions accessible through this video-projection system and report the fabrication of critical microfluidic components (junctions, straight channels, and curved channels). To exemplify the process, three common devices are produced using this method: a droplet generation device, a gradient generation device, and a neuro-engineering oriented device. The neuro-engineering oriented device is a compartmentalized microfluidic chip, and therefore, required the production and the precise alignment of two different masks.

  6. Prototyping the PANDA Barrel DIRC

    Energy Technology Data Exchange (ETDEWEB)

    Schwarz, C., E-mail: C.Schwarz@gsi.de [GSI Helmholtzzentrum für Schwerionenforschung GmbH, Darmstadt (Germany); Kalicy, G.; Dzhygadlo, R.; Gerhardt, A.; Götzen, K.; Hohler, R.; Kumawat, H.; Lehmann, D.; Lewandowski, B.; Patsyuk, M.; Peters, K.; Schepers, G.; Schmitt, L.; Schwiening, J.; Traxler, M.; Zühlsdorf, M. [GSI Helmholtzzentrum für Schwerionenforschung GmbH, Darmstadt (Germany); Dodokhov, V.Kh. [Joint Institute for Nuclear Research, Dubna (Russian Federation); Britting, A.; Eyrich, W.; Lehmann, A. [Friedrich Alexander-University of Erlangen-Nuremberg, Erlangen (Germany); and others

    2014-12-01

    The design of the Barrel DIRC detector for the future PANDA experiment at FAIR contains several important improvements compared to the successful BABAR DIRC, such as focusing and fast timing. To test those improvements as well as other design options a prototype was build and successfully tested in 2012 with particle beams at CERN. The prototype comprises a radiator bar, focusing lens, mirror, and a prism shaped expansion volume made of synthetic fused silica. An array of micro-channel plate photomultiplier tubes measures the location and arrival time of the Cherenkov photons with sub-nanosecond resolution. The development of a fast reconstruction algorithm allowed to tune construction details of the detector setup with test beam data and Monte-Carlo simulations.

  7. Customer-experienced rapid prototyping

    Science.gov (United States)

    Zhang, Lijuan; Zhang, Fu; Li, Anbo

    2008-12-01

    In order to describe accurately and comprehend quickly the perfect GIS requirements, this article will integrate the ideas of QFD (Quality Function Deployment) and UML (Unified Modeling Language), and analyze the deficiency of prototype development model, and will propose the idea of the Customer-Experienced Rapid Prototyping (CE-RP) and describe in detail the process and framework of the CE-RP, from the angle of the characteristics of Modern-GIS. The CE-RP is mainly composed of Customer Tool-Sets (CTS), Developer Tool-Sets (DTS) and Barrier-Free Semantic Interpreter (BF-SI) and performed by two roles of customer and developer. The main purpose of the CE-RP is to produce the unified and authorized requirements data models between customer and software developer.

  8. DOE's annealing prototype demonstration projects

    International Nuclear Information System (INIS)

    Warren, J.; Nakos, J.; Rochau, G.

    1997-01-01

    One of the challenges U.S. utilities face in addressing technical issues associated with the aging of nuclear power plants is the long-term effect of plant operation on reactor pressure vessels (RPVs). As a nuclear plant operates, its RPV is exposed to neutrons. For certain plants, this neutron exposure can cause embrittlement of some of the RPV welds which can shorten the useful life of the RPV. This RPV embrittlement issue has the potential to affect the continued operation of a number of operating U.S. pressurized water reactor (PWR) plants. However, RPV material properties affected by long-term irradiation are recoverable through a thermal annealing treatment of the RPV. Although a dozen Russian-designed RPVs and several U.S. military vessels have been successfully annealed, U.S. utilities have stated that a successful annealing demonstration of a U.S. RPV is a prerequisite for annealing a licensed U.S. nuclear power plant. In May 1995, the Department of Energy's Sandia National Laboratories awarded two cost-shared contracts to evaluate the feasibility of annealing U.S. licensed plants by conducting an anneal of an installed RPV using two different heating technologies. The contracts were awarded to the American Society of Mechanical Engineers (ASME) Center for Research and Technology Development (CRTD) and MPR Associates (MPR). The ASME team completed its annealing prototype demonstration in July 1996, using an indirect gas furnace at the uncompleted Public Service of Indiana's Marble Hill nuclear power plant. The MPR team's annealing prototype demonstration was scheduled to be completed in early 1997, using a direct heat electrical furnace at the uncompleted Consumers Power Company's nuclear power plant at Midland, Michigan. This paper describes the Department's annealing prototype demonstration goals and objectives; the tasks, deliverables, and results to date for each annealing prototype demonstration; and the remaining annealing technology challenges

  9. Encapsulation of polymer photovoltaic prototypes

    Energy Technology Data Exchange (ETDEWEB)

    Krebs, Frederik C. [The Danish Polymer Centre, RISOE National Laboratory, P.O. Box 49, DK-4000 Roskilde (Denmark)

    2006-12-15

    A simple and efficient method for the encapsulation of polymer and organic photovoltaic prototypes is presented. The method employs device preparation on glass substrates with subsequent sealing using glass fiber reinforced thermosetting epoxy (prepreg) against a back plate. The method allows for transporting oxygen and water sensitive devices outside a glove box environment after sealing and enables sharing of devices between research groups such that efficiency and stability can be evaluated in different laboratories. (author)

  10. Yucca Mountain project prototype testing

    International Nuclear Information System (INIS)

    Hughes, W.T.; Girdley, W.A.

    1990-01-01

    The U.S. DOE is responsible for characterizing the Yucca Mountain site in Nevada to determine its suitability for development as a geologic repository to isolate high-level nuclear waste for at least 10,000 years. This unprecedented task relies in part on measurements made with relatively new methods or applications, such as dry coring and overcoring for studies to be conducted from the land surface and in an underground facility. The Yucca Mountain Project has, since 1988, implemented a program of equipment development and methods development for a broad spectrum of hydrologic, geologic, rock mechanics, and thermomechanical tests planned for use in an Exploratory Shaft during site characterization at the Yucca Mountain site. A second major program was fielded beginning in April 1989 to develop and test methods and equipment for surface drilling to obtain core samples from depth using only air as a circulating medium. The third major area of prototype testing has been during the ongoing development of the Instrumentation/ Data Acquisition System (IDAS), designed to collect and monitor data from down-hole instrumentation in the unsaturated zone, and store and transmit the data to a central archiving computer. Future prototype work is planned for several programs including the application of vertical seismic profiling methods and flume design to characterizing the geology at Yucca Mountain. The major objectives of this prototype testing are to assure that planned Site Characterization testing can be carried out effectively at Yucca Mountain, both in the Exploratory Shaft Facility (ESF), and from the surface, and to avoid potential major failures or delays that could result from the need to re-design testing concepts or equipment. This paper will describe the scope of the Yucca Mountain Project prototype testing programs and summarize results to date. 3 figs

  11. Prototype Morphing Fan Nozzle Demonstrated

    Science.gov (United States)

    Lee, Ho-Jun; Song, Gang-Bing

    2004-01-01

    Ongoing research in NASA Glenn Research Center's Structural Mechanics and Dynamics Branch to develop smart materials technologies for aeropropulsion structural components has resulted in the design of the prototype morphing fan nozzle shown in the photograph. This prototype exploits the potential of smart materials to significantly improve the performance of existing aircraft engines by introducing new inherent capabilities for shape control, vibration damping, noise reduction, health monitoring, and flow manipulation. The novel design employs two different smart materials, a shape-memory alloy and magnetorheological fluids, to reduce the nozzle area by up to 30 percent. The prototype of the variable-area fan nozzle implements an overlapping spring leaf assembly to simplify the initial design and to provide ease of structural control. A single bundle of shape memory alloy wire actuators is used to reduce the nozzle geometry. The nozzle is subsequently held in the reduced-area configuration by using magnetorheological fluid brakes. This prototype uses the inherent advantages of shape memory alloys in providing large induced strains and of magnetorheological fluids in generating large resistive forces. In addition, the spring leaf design also functions as a return spring, once the magnetorheological fluid brakes are released, to help force the shape memory alloy wires to return to their original position. A computerized real-time control system uses the derivative-gain and proportional-gain algorithms to operate the system. This design represents a novel approach to the active control of high-bypass-ratio turbofan engines. Researchers have estimated that such engines will reduce thrust specific fuel consumption by 9 percent over that of fixed-geometry fan nozzles. This research was conducted under a cooperative agreement (NCC3-839) at the University of Akron.

  12. Using prototyping in software development

    OpenAIRE

    Šinkovec, Miha

    2010-01-01

    Today the business system changers faster than the usual conventional cascade life cycle. Because of that, we can conclude, that today's programming system will no longer be presented as the answer to this topic in the developing age of ever changing user requirements. Neither increased performance or higher productivity will decrease the problem. The appropriate solution to this stated problem is prototyping. Instead of building and developing the whole system, we build a module that can...

  13. Mineral commodity summaries 2015

    Science.gov (United States)

    ,

    2015-01-01

    Each chapter of the 2015 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2014 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses.

  14. Iteration and Prototyping in Creating Technical Specifications.

    Science.gov (United States)

    Flynt, John P.

    1994-01-01

    Claims that the development process for computer software can be greatly aided by the writers of specifications if they employ basic iteration and prototyping techniques. Asserts that computer software configuration management practices provide ready models for iteration and prototyping. (HB)

  15. Printing of Titanium implant prototype

    International Nuclear Information System (INIS)

    Wiria, Florencia Edith; Shyan, John Yong Ming; Lim, Poon Nian; Wen, Francis Goh Chung; Yeo, Jin Fei; Cao, Tong

    2010-01-01

    Dental implant plays an important role as a conduit of force and stress to flow from the tooth to the related bone. In the load sharing between an implant and its related bone, the amount of stress carried by each of them directly related to their stiffness or modulus. Hence, it is a crucial issue for the implant to have matching mechanical properties, in particular modulus, between the implant and its related bone. Titanium is a metallic material that has good biocompatibility and corrosion resistance. Whilst the modulus of the bulk material is still higher than that of bone, it is the lowest among all other commonly used metallic implant materials, such as stainless steel or cobalt alloy. Hence it is potential to further reduce the modulus of pure Titanium by engineering its processing method to obtain porous structure. In this project, porous Titanium implant prototype is fabricated using 3-dimensional printing. This technique allows the flexibility of design customization, which is beneficial for implant fabrication as tailoring of implant size and shape helps to ensure the implant would fit nicely to the patient. The fabricated Titanium prototype had a modulus of 4.8-13.2 GPa, which is in the range of natural bone modulus. The compressive strength achieved was between 167 to 455 MPa. Subsequent cell culture study indicated that the porous Titanium prototype had good biocompatibility and is suitable for bone cell attachment and proliferation.

  16. Majorana Thermosyphon Prototype Experimental Results

    International Nuclear Information System (INIS)

    Fast, James E.; Reid, Douglas J.; Aguayo Navarrete, Estanislao

    2010-01-01

    The Majorana demonstrator will operate at liquid Nitrogen temperatures to ensure optimal spectrometric performance of its High Purity Germanium (HPGe) detector modules. In order to transfer the heat load of the detector module, the Majorana demonstrator requires a cooling system that will maintain a stable liquid nitrogen temperature. This cooling system is required to transport the heat from the detector chamber outside the shield. One approach is to use the two phase liquid-gas equilibrium to ensure constant temperature. This cooling technique is used in a thermosyphon. The thermosyphon can be designed so the vaporization/condensing process transfers heat through the shield while maintaining a stable operating temperature. A prototype of such system has been built at PNNL. This document presents the experimental results of the prototype and evaluates the heat transfer performance of the system. The cool down time, temperature gradient in the thermosyphon, and heat transfer analysis are studied in this document with different heat load applied to the prototype.

  17. ASEAN Mineral Database and Information System (AMDIS)

    Science.gov (United States)

    Okubo, Y.; Ohno, T.; Bandibas, J. C.; Wakita, K.; Oki, Y.; Takahashi, Y.

    2014-12-01

    AMDIS has lunched officially since the Fourth ASEAN Ministerial Meeting on Minerals on 28 November 2013. In cooperation with Geological Survey of Japan, the web-based GIS was developed using Free and Open Source Software (FOSS) and the Open Geospatial Consortium (OGC) standards. The system is composed of the local databases and the centralized GIS. The local databases created and updated using the centralized GIS are accessible from the portal site. The system introduces distinct advantages over traditional GIS. Those are a global reach, a large number of users, better cross-platform capability, charge free for users, charge free for provider, easy to use, and unified updates. Raising transparency of mineral information to mining companies and to the public, AMDIS shows that mineral resources are abundant throughout the ASEAN region; however, there are many datum vacancies. We understand that such problems occur because of insufficient governance of mineral resources. Mineral governance we refer to is a concept that enforces and maximizes the capacity and systems of government institutions that manages minerals sector. The elements of mineral governance include a) strengthening of information infrastructure facility, b) technological and legal capacities of state-owned mining companies to fully-engage with mining sponsors, c) government-led management of mining projects by supporting the project implementation units, d) government capacity in mineral management such as the control and monitoring of mining operations, and e) facilitation of regional and local development plans and its implementation with the private sector.

  18. Prototype effect and the persuasiveness of generalizations

    OpenAIRE

    Dahlman, Christian; Sarwar, Farhan; Bååth, Rasmus; Wahlberg, Lena; Sikström, Sverker

    2015-01-01

    An argument that makes use of a generalization activates the prototype for the category used in the generalization. We conducted two experiments that investigated how the activation of the prototype affects the persuasiveness of the argument. The results of the experiments suggest that the features of the prototype overshadow and partly overwrite the actual facts of the case. The case is, to some extent, judged as if it had the features of the prototype instead of the features it actually ...

  19. [Mineral water as a cure].

    Science.gov (United States)

    Nocco, Priska Binz

    2008-01-01

    resorts mentioned, especially regarding the quality and quantity aspects of the performed mineral water analyses, as well as in the reported written evidence and publications on the success of the therapies. Differences were also to be found in the conditions of the health resort facilities and in the medical support given. The therapy opportunities included mainly drinking and bath cures, which could occur alone or in combination. In the mentioned health resorts different clinical disease symptoms were treated. The most important baths were located in Acquarossa and Stabio, which were specialized in selected therapeutical domains, because of their particular water compositions. Numerous personalities from science and politics were concerned by the local springs and accepted to contribute to the promotion of these structures. Their engagement led to the integration of the native springs in the Farmacopea Ticinese. Since at that time it was extremely difficult to find experienced mineral water analysts in the region, the analyses of local native sources were assigned to qualified experts mainly coming from Italy. This scientific co-operation between the southern part of Switzerland and the northern part of Italy was, already at that time, active also in other work domains. The evaluation of the historical documentation available from the Farmacia Vantussi shows that this pharmacy supplied a considerable assortment of national and foreign spring waters, as well as foreign dried components. Of commercial interest was, to be noted, the free sale of the waters to hospitals, institutions, hotels, restaurants as well as to private households. The sales of waters and of their dried components upon prescription, however, constituted only the minor part. The introduction of the industrial bottling occurring in the first decades of the 20th century, led to a lowering price trend, through which the product 'mineral water' became accessible to a broader public. Henceforth its

  20. Implicit face prototype learning from geometric information.

    Science.gov (United States)

    Or, Charles C-F; Wilson, Hugh R

    2013-04-19

    There is evidence that humans implicitly learn an average or prototype of previously studied faces, as the unseen face prototype is falsely recognized as having been learned (Solso & McCarthy, 1981). Here we investigated the extent and nature of face prototype formation where observers' memory was tested after they studied synthetic faces defined purely in geometric terms in a multidimensional face space. We found a strong prototype effect: The basic results showed that the unseen prototype averaged from the studied faces was falsely identified as learned at a rate of 86.3%, whereas individual studied faces were identified correctly 66.3% of the time and the distractors were incorrectly identified as having been learned only 32.4% of the time. This prototype learning lasted at least 1 week. Face prototype learning occurred even when the studied faces were further from the unseen prototype than the median variation in the population. Prototype memory formation was evident in addition to memory formation of studied face exemplars as demonstrated in our models. Additional studies showed that the prototype effect can be generalized across viewpoints, and head shape and internal features separately contribute to prototype formation. Thus, implicit face prototype extraction in a multidimensional space is a very general aspect of geometric face learning. Copyright © 2013 Elsevier Ltd. All rights reserved.

  1. The Scintillator Tile Hadronic Calorimeter Prototype

    International Nuclear Information System (INIS)

    Rusinov, V.

    2006-01-01

    A high granularity scintillator hadronic calorimeter prototype is described. The calorimeter is based on a novel photodetector - Silicon Photo-Multiplier (SiPM). The main parameters of SiPM are discussed as well as readout cell construction and optimization. The experience with a small prototype production and testing is described. A new 8 k channel prototype is being manufactured now

  2. Rapid Prototyping: An Alternative Instructional Design Strategy.

    Science.gov (United States)

    Tripp, Steven D.; Bichelmeyer, Barbara

    1990-01-01

    Discusses the nature of instructional design and describes rapid prototyping as a feasible model for instructional system design (ISD). The use of prototyping in software engineering is described, similarities between software design and instructional design are discussed, and an example is given which uses rapid prototyping in designing a…

  3. Mineral distributions at the developing tendon enthesis.

    Science.gov (United States)

    Schwartz, Andrea G; Pasteris, Jill D; Genin, Guy M; Daulton, Tyrone L; Thomopoulos, Stavros

    2012-01-01

    Tendon attaches to bone across a functionally graded interface, "the enthesis". A gradient of mineral content is believed to play an important role for dissipation of stress concentrations at mature fibrocartilaginous interfaces. Surgical repair of injured tendon to bone often fails, suggesting that the enthesis does not regenerate in a healing setting. Understanding the development and the micro/nano-meter structure of this unique interface may provide novel insights for the improvement of repair strategies. This study monitored the development of transitional tissue at the murine supraspinatus tendon enthesis, which begins postnatally and is completed by postnatal day 28. The micrometer-scale distribution of mineral across the developing enthesis was studied by X-ray micro-computed tomography and Raman microprobe spectroscopy. Analyzed regions were identified and further studied by histomorphometry. The nanometer-scale distribution of mineral and collagen fibrils at the developing interface was studied using transmission electron microscopy (TEM). A zone (∼20 µm) exhibiting a gradient in mineral relative to collagen was detected at the leading edge of the hard-soft tissue interface as early as postnatal day 7. Nanocharacterization by TEM suggested that this mineral gradient arose from intrinsic surface roughness on the scale of tens of nanometers at the mineralized front. Microcomputed tomography measurements indicated increases in bone mineral density with time. Raman spectroscopy measurements revealed that the mineral-to-collagen ratio on the mineralized side of the interface was constant throughout postnatal development. An increase in the carbonate concentration of the apatite mineral phase over time suggested possible matrix remodeling during postnatal development. Comparison of Raman-based observations of localized mineral content with histomorphological features indicated that development of the graded mineralized interface is linked to endochondral

  4. Biointrusion test plan for the Permanent Isolation Surface Barrier Prototype

    International Nuclear Information System (INIS)

    Link, S.O.; Cadwell, L.L.; Brandt, C.A.; Downs, J.L.; Rossi, R.E.; Gee, G.W.

    1994-04-01

    This document provides a testing and monitoring plan for the biological component of the prototype barrier slated for construction at the Hanford Site. The prototype barrier is an aboveground structure engineered to demonstrate the basic features of an earthen cover system. It is designed to permanently isolate waste from the biosphere. The features of the barrier include multiple layers of soil and rock materials and a low-permeability asphalt sublayer. The surface of the barrier consists of silt loam soil, covered with plants. The barrier sides are reinforced with rock or coarse earthen-fill to protect against wind and water erosion. The sublayers inhibit plant and animal intrusion and percolation of water. A series of tests will be conducted on the prototype barrier over the next several years to evaluate barrier performance under extreme climatic conditions. Plants and animals will play a significant role in the hydrologic and water and wind erosion characteristics of the prototype barrier. Studies on the biological component of the prototype barrier will include work on the initial revegetation of the surface, continued monitoring of the developing plant community, rooting depth and dispersion in the context of biointrusion potential, the role of plants in the hydrology of the surface and toe regions of the barrier, the role of plants in stabilizing the surface against water and wind erosion, and the role of burrowing animals in the hydrology and water and wind erosion of the barrier

  5. Fissure minerals, literature review

    International Nuclear Information System (INIS)

    Larsson, S.Aa.

    1980-01-01

    This paper is a review of methods used for direct and indirect dating of tectonic events. Isotope geochemistry including stable isotopes as well as fission track- dating, fluid inclusion and thermoluminescens techniques have been considered. It has been concluded that an investigation of tectonic (and thermal) events should start with a detailed study of the mineral phases grown in seald fissures as well as minerals from fissure walls. This study should include phase identification, textures as well as mineral chemistry. The information from this study is fundamental for the decision of further investigations. Mineral chemistry including isotopes and fluid inclusion studies will give an essential knowledge about crystallization conditions for fissure minerals concerned. Direct dating using fission tracks as well as radioactive isotopes could be useful for some minerals. Application of thermoluminescens dating on fissure minerals is doubtful. (Auth.)

  6. Project management strategies for prototyping breakdowns

    DEFF Research Database (Denmark)

    Granlien, Maren Sander; Pries-Heje, Jan; Baskerville, Richard

    2009-01-01

    , managing the explorative and iterative aspects of prototyping projects is not a trivial task. We examine the managerial challenges in a small scale prototyping project in the Danish healthcare sector where a prototype breakdown and project escalation occurs. From this study we derive a framework...... of strategies for coping with escalation in troubled prototyping projects; the framework is based on project management triangle theory and is useful when considering how to manage prototype breakdown and escalation. All strategies were applied in the project case at different points in time. The strategies led...

  7. OPTICAL-ELECTRONIC SYSTEM FOR EXPRESS ANALYSIS OF ORE DRESSABILITY FOR MINERAL RAW MATERIALS BY OPTICAL METHOD

    Directory of Open Access Journals (Sweden)

    A. A. Alekhin

    2013-05-01

    Full Text Available The article deals with creation results of experimental prototype of optical-electronic complex, designed to assess ore dressability of mineral raw materials by optical sorting method.

  8. Mineral exploration with ERTS imagery. [Colorado

    Science.gov (United States)

    Nicolais, S. M.

    1974-01-01

    Ten potential target areas for metallic mineral exploration were selected on the basis of a photo-lineament interpretation of the ERTS image 1172-17141 in central Colorado. An evaluation of bias indicated that prior geologic knowledge of the region had little, if any, effect on target selection. In addition, a contoured plot of the frequency of photo-lineament intersections was made to determine what relationships exist between the photo-lineaments and mineral districts. Comparison of this plot with a plot of the mineral districts indicates that areas with a high frequency of intersections commonly coincide with known mineral districts. The results of this experiment suggest that photo-lineaments are fractures or fracture-controlled features, and their distribution may be a guide to metallic mineral deposits in Colorado, and probably other areas as well.

  9. Results from the FDIRC prototype

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, D.A., E-mail: roberts@umd.edu [University of Maryland, College Park, MD 20742 (United States); Arnaud, N. [Laboratoire de l’Accélérateur Linéaire, Centre Scientifique d’Orsay, F-91898 Orsay Cedex (France); Dey, B. [University of California, Riverside, CA 92521 (United States); Borsato, M. [Laboratoire de l’Accélérateur Linéaire, Centre Scientifique d’Orsay, F-91898 Orsay Cedex (France); Leith, D.W.G.S.; Nishimura, K.; Ratcliff, B.N. [SLAC, Stanford University, Palo Alto, CA 94309 (United States); Varner, G. [University of Hawaii, Honolulu, HI 96822 (United States); Va’vra, J. [SLAC, Stanford University, Palo Alto, CA 94309 (United States)

    2014-12-01

    We present results from a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC). This detector was designed as a prototype of the particle identification system for the SuperB experiment, and comprises 1/12 of the SuperB barrel azimuthal coverage with partial electronics implementation. The prototype was tested in the SLAC Cosmic Ray Telescope (CRT) which provides 3-D muon tracking with an angular resolution of ∼1.5 mrad, track position resolution of 5–6 mm, start time resolution of 70 ps, and a muon low-energy cutoff of ∼2 GeV provided by an iron range stack. The quartz focusing photon camera couples to a full-size BaBar DIRC bar box and is read out by 12 Hamamatsu H8500 MaPMTs providing 768 pixels. We used IRS2 waveform digitizing electronics to read out the MaPMTs. We present several results from our on-going development activities that demonstrate that the new optics design works very well, including: (a) single photon Cherenkov angle resolutions with and without chromatic corrections, (b) S/N ratio between the Cherenkov peak and background, which consists primarily of ambiguities in possible photon paths to a given pixel, (c) dTOP=TOP{sub measured}–TOP{sub expected} resolutions, and (d) performance of the detector in the presence of high-rate backgrounds. We also describe data analysis methods and point out limits of the present performance. - Highlights: • We present results from a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC). • The prototype was tested in the SLAC Cosmic Ray Telescope (CRT) which provides 3-D muon tracking. • We present several results from our on-going development activities that demonstrate that new optics design works very well. • We describe data analysis methods and point out limits of the present performance.

  10. Digital Prototyping of Milk Products

    DEFF Research Database (Denmark)

    Frisvad, Jeppe Revall; Nielsen, Otto Højager Attermann; Skytte, Jacob Lercke

    2012-01-01

    reflectance measurements can be used for more extensive validation and for gathering data that can be used to extend our current model such that it can also predict how the optical properties develop during fermentation or acidification of milk to yogurt. A well-established way of measuring optical properties...... prototyping of milk products such that it can also predict how the optical properties develop during gelation of milk to yogurt. The influence of the colloidal aggregation on the optical properties is described by the static structure factor. As our method is noninvasive, we can use our setup for monitoring...

  11. Mechanical Prototyping and Manufacturing Internship

    Science.gov (United States)

    Grenfell, Peter

    2016-01-01

    The internship was located at the Johnson Space Center (JSC) Innovation Design Center (IDC), which is a facility where the JSC workforce can meet and conduct hands-on innovative design, fabrication, evaluation, and testing of ideas and concepts relevant to NASA's mission. The tasks of the internship included mechanical prototyping design and manufacturing projects in service of research and development as well as assisting the users of the IDC in completing their manufacturing projects. The first project was to manufacture hatch mechanisms for a team in the Systems Engineering and Project Advancement Program (SETMAP) hexacopter competition. These mechanisms were intended to improve the performance of the servomotors and offer an access point that would also seal to prevent cross-contamination. I also assisted other teams as they were constructing and modifying their hexacopters. The success of this competition demonstrated a proof of concept for aerial reconnaissance and sample return to be potentially used in future NASA missions. I also worked with Dr. Kumar Krishen to prototype an improved thermos and a novel, portable solar array. Computer-aided design (CAD) software was used to model the parts for both of these projects. Then, 3D printing as well as conventional techniques were used to produce the parts. These prototypes were then subjected to trials to determine the success of the designs. The solar array is intended to work in a cluster that is easy to set up and take down and doesn't require powered servomechanisms. It could be used terrestrially in areas not serviced by power grids. Both projects improve planetary exploration capabilities to future astronauts. Other projects included manufacturing custom rail brackets for EG-2, assisting engineers working on underwater instrument and tool cases for the NEEMO project, and helping to create mock-up parts for Space Center Houston. The use of the IDC enabled efficient completion of these projects at

  12. Prototype system of secure VOD

    Science.gov (United States)

    Minemura, Harumi; Yamaguchi, Tomohisa

    1997-12-01

    Secure digital contents delivery systems are to realize copyright protection and charging mechanism, and aim at secure delivery service of digital contents. Encrypted contents delivery and history (log) management are means to accomplish this purpose. Our final target is to realize a video-on-demand (VOD) system that can prevent illegal usage of video data and manage user history data to achieve a secure video delivery system on the Internet or Intranet. By now, mainly targeting client-server systems connected with enterprise LAN, we have implemented and evaluated a prototype system based on the investigation into the delivery method of encrypted video contents.

  13. CERN LHC dipole prototype success

    International Nuclear Information System (INIS)

    Anon.

    1994-01-01

    In a crash programme, the first prototype superconducting dipole magnet for CERN's LHC protonproton collider was successfully powered for the first time at CERN on 14 April, eventually sailing to 9T, above the 8.65T nominal LHC field, before quenching for the third time. The next stage is to install the delicate measuring system for making comprehensive magnetic field maps in the 10 m long, 50 mm diameter twin-apertures of the magnet. These measurements will check that the required LHC field quality has been achieved at both the nominal and injection fields

  14. Prototype plutonium-storage monitor

    International Nuclear Information System (INIS)

    Bliss, M.; Craig, R.A.; Sunberg, D.S.; Warner, R.A.

    1996-01-01

    Pacific Northwest National Laboratory (PNNL) has fabricated cerium-activated lithium silicate scintillating fibers via a hot-downdraw process. These fibers typically have an operational transmission length (e -1 length) of greater than 2 meters. This permits the fabrication of devices that, hitherto, were not possible to consider. A prototype neutron monitor for scrap Pu-storage containers was fabricated and tested for 70 days, taking data with a variety of sources in a high-background environment. These data and their implication in the context of a storage-monitor situation are discussed

  15. FY97 ICCS prototype specification

    International Nuclear Information System (INIS)

    Woodruff, J.

    1997-01-01

    The ICCS software team will implement and test two iterations of their software product during FY97. This document specifies the products to be delivered in that first prototype and projects the direction that the second prototype will take. Detailed specification of the later iteration will be written when the results of the first iteration are complete. The selection of frameworks to be implemented early is made on a basis of risk analysis from the point of view of future development in the ICCS project. The prototype will address risks in integration of object- oriented components, in refining our development process, and in emulation testing for FEP devices. This document is a specification that identifies products and processes to undertake for resolving these risks. The goals of this activity are to exercise our development process at a modest scale and to probe our architecture plan for fundamental limits and failure modes. The product of the iterations will be the framework software which will be useful in future ICCS code. Thus the FY97 products are intended for internal usage by the ICCS team and for demonstration to the FEP software developers of the strategy for integrating supervisory software with FEP computers. This will be the first of several expected iterations of the software development process and the performance measurements that ICCS will demonstrate, intended to support confidence in our ability to meet project RAM goals. The design of the application software is being carried out in a separate WBS 1.5.2 activity. The design activity has as its FY97 product a series of Software Design Documents that will specify the functionality of the controls software of ICCS. During the testing of this year''s prototypes, the application functionality needed for test will be provided by sample maintenance controls. These are early precursors of controls that can be used for low level device control. Since the devices under test will be represented by

  16. Rapid prototyping of robotic platforms

    CSIR Research Space (South Africa)

    De Ronde, Willis

    2016-11-01

    Full Text Available of thickness up to 200mm can be cut to create prototype chassis/ bodies or even the final product. One of the few limitations is the cutting of certain laminated materials, as this tends to produce delaminated cutting edges or even fractures in the case... mine inspection robot (Shongololo). Shongololo’s frame is made from engineering plastics while the chassis of Dassie was made from aluminium and cut using abrasive waterjet machining. The advantage of using abrasive waterjet machining is the speed...

  17. Bismuth-silver mineralization in the Sergozerskoe gold occurrence

    Directory of Open Access Journals (Sweden)

    Kalinin A. A.

    2017-03-01

    Full Text Available Bismuth-silver mineralization attendant to gold mineralization in the Sergozerskoe gold occurrence has been studied in detail. Bi-Ag mineralization is connected with diorite porphyry dykes, which cut volcanic-sedimentary Lopian complexes of the Strel'ninsky greenstone belt – hornblendite and actinolite-chlorite amphibolites, biotite and bi-micaceous gneisses. Distribution of Bi-Ag mineralization similar to gold mineralization is controlled by 80 m thick zone of silicification. Bi minerals are found in brecciated diorite porphyry. Bismuth-silver mineralization includes native metals (bismuth, electrum, silver, tellurides (hedleyite, hessite, selenides (ikunolite, sulfides and sulfosalts of Bi and Ag (matildite, lillianite, eckerite, jalpaite, prustite, acanthite, a few undiagnosed minerals. All Bi and Ag minerals associate with galena. Composition of mineralization evolved from early to late stages of development, depending on intensity of rock alteration. The earliest Bi-Ag minerals were native bismuth and hedleyite formed dissemination in galena, and electrum with 30-45 mass.% Au. Later native bismuth was partly substituted by silver and bismuth sulfosalts and bismuth sulfides. The latest minerals were low-temperature silver sulfides eckerite, jalpaite, and acanthite, which were noted only in the most intensively altered rocks. As soon as the process of formation of Bi-Ag mineralization is the same as formation of gold, findings of bismuth-silver mineralization can serve as a positive exploration sign for gold in the region.

  18. Grouping Minerals by Their Formulas

    Science.gov (United States)

    Mulvey, Bridget

    2018-01-01

    Minerals are commonly taught in ways that emphasize mineral identification for its own sake or maybe to help identify rocks. But how do minerals fit in with other science content taught? The author uses mineral formulas to help Earth science students wonder about the connection between elements, compounds, mixtures, minerals, and mineral formulas.…

  19. Laachite, (Ca,Mn){sub 2}Zr{sub 2}Nb{sub 2}TiFeO{sub 14}, a new zirconolite-related mineral from the Eifel volcanic region, Germany

    Energy Technology Data Exchange (ETDEWEB)

    Chukanov, Nikita V. [Institute of Problems of Chemical Physics, Chernogolovka (Russian Federation); Krivovichev, Sergey V.; Pakhomova, Anna S. [St. Petersburg State Univ. (Russian Federation). Faculty of Crystallography; Pekov, Igor V.; Vigasina, Marina F. [Moscow State Univ. (Russian Federation). Faculty of Geology; Schaefer, Christof [Suedwestdeutsche Salzwerke AG, Heilbronn (Germany); Van, Konstantin V. [Russian Academy of Sciences, Chernogolovka (Russian Federation). Inst. of Experimental Mineralogy

    2014-02-15

    The new mineral laachite was discovered in a sanidinite specimen from the Laach Lake (Laacher See) volcano, Eifel region, Rheinland-Pfalz, Germany. Associated minerals are sanidine, allanite-(Ce), baddeleyite, hau¨yne, hedenbergite, intermediate members of the jacobsite-magnetite series, phlogopite, rhodonite, spessartine, tephroite, thorite, zircon, and a pyrochlore-group mineral. Laachite is deep brownish-red, has an adamantine lustre, and is translucent; the streak is brownish red. It forms longprismatic crystals up to 0.02 x 0.04 x 0.5 mm, which are present as random intergrowths and twins in cavities within sanidinite. The density calculated from the empirical formula is 5.417 g/cm{sup 3}. The mean refractive index calculated from the Gladstone-Dale relationship is 2.26. The Raman spectrum shows the absence of hydrogen-bearing groups. The chemical composition is (electron microprobe, mean of 5 analyses, wt. %): CaO 4.29, MnO 9.42, FeO 5.73, Y{sub 2}O{sub 3} 2.56, La{sub 2}O{sub 3} 2.00, Ce{sub 2}O{sub 3} 6.37, Nd{sub 2}O{sub 3} 2.22, Al{sub 2}O{sub 3} 0.99, ThO{sub 2} 7.75, TiO{sub 2} 10.98, ZrO{sub 2} 19.39, Nb{sub 2}O{sub 5} 27.82, total 99.52. The empirical formula based on 14 O atoms is: (Ca{sub 0.66}Mn{sub 0.37}Th{sub 0.25}Y{sub 0.20}La{sub 0.11}Ce{sub 0.34}Nd{sub 0.11})(Zr{sub 1.3} {sub 6}Mn{sub 0.64})(Nb{sub 1.81}Ti{sub 1.19})(Fe{sub 0.69}Al{sub 0.17}Mn{sub 0.14})O{sub 14.00}. The simplified formula, taking into account the structural data, is: (Ca,Mn){sub 2}(Zr,Mn){sub 2}Nb{sub 2}TiFeO{sub 14}. Laachite is monoclinic, space group C2/c, a = 7.3119(5), b = 14.1790(10), c = 10.1700(7)Aa, β = 90.072(2), V = 1054.38(1) Aa{sup 3}, Z = 4. The crystal structure was solved using single-crystal X-ray diffraction data. Laachite is a monoclinic analogue of zirconolite-3O, CaZrTi{sub 2}O{sub 7}, with Nb dominant over Ti in the octahedral sites Nb1 and Nb2 and Fe dominant in a site with four-fold coordination. The strongest lines of the powder X-ray diffraction

  20. Low-friction nanojoint prototype

    Science.gov (United States)

    Vlassov, Sergei; Oras, Sven; Antsov, Mikk; Butikova, Jelena; Lõhmus, Rünno; Polyakov, Boris

    2018-05-01

    High surface energy of individual nanostructures leads to high adhesion and static friction that can completely hinder the operation of nanoscale systems with movable parts. For instance, silver or gold nanowires cannot be moved on silicon substrate without plastic deformation. In this paper, we experimentally demonstrate an operational prototype of a low-friction nanojoint. The movable part of the prototype is made either from a gold or silver nano-pin produced by laser-induced partial melting of silver and gold nanowires resulting in the formation of rounded bulbs on their ends. The nano-pin is then manipulated into the inverted pyramid (i-pyramids) specially etched in a Si wafer. Due to the small contact area, the nano-pin can be repeatedly tilted inside an i-pyramid as a rigid object without noticeable deformation. At the same time in the absence of external force the nanojoint is stable and preserves its position and tilt angle. Experiments are performed inside a scanning electron microscope and are supported by finite element method simulations.

  1. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 4 discusses the following topics: Rod Compaction/Loading System Test Results and Analysis Report; Waste Collection System Test Results and Analysis Report; Waste Container Transfer Fixture Test Results and Analysis Report; Staging and Cutting Table Test Results and Analysis Report; and Upper Cutting System Test Results and Analysis Report

  2. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 5 discusses the following topics: Lower Cutting System Test Results and Analysis Report; NFBC Loading System Test Results and Analysis Report; Robotic Bridge Transporter Test Results and Analysis Report; RM-10A Remotec Manipulator Test Results and Analysis Report; and Manipulator Transporter Test Results and Analysis Report

  3. 43 CFR 19.8 - Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

    Science.gov (United States)

    2010-10-01

    ... patents, and mineral leasing within National Forest Wilderness. 19.8 Section 19.8 Public Lands: Interior... § 19.8 Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest... locations, mineral patents, and mineral leasing within National Forest Wilderness are contained in parts...

  4. Radioactive mineral deposits

    Energy Technology Data Exchange (ETDEWEB)

    1948-01-01

    This publication was designed as a guide for uranium and thorium prospectors in Australia. Physical properties, such as color, streak, luster, hardness, fracture, and specific gravity of the uranium and thorium-bearing minerals are summarized and the various methods suitable for detecting radioactivity in minerals are described. Two colored plates show samples of pitchblende (uraninite), autunite, carnotite, monazite, and others of the most important minerals sources of uranium and thorium.

  5. Structural dimensioning of dual purpose cask prototype

    International Nuclear Information System (INIS)

    Silva, Luiz Leite da; Mourao, Rogerio Pimenta; Lopes, Claudio Cunha

    2005-01-01

    The structural dimensioning of a Type B(U) dual purpose cask prototype is part of the scope of work of the Brazilian institute CDTN in the IAEA regional project involving Latin American countries which operate research reactors (Argentina, Brazil, Chile, Mexico and Peru). In order to meet the dimensional and operational characteristics of the reactor facilities in these countries, a maximum weight of 10.000 kgf and a maximum dimension of 1 m in at least one direction were set for the cask. With these design restrictions, the cask's payload is either 21 MTR or 78 TRIGA fuel elements. The cask's most important components are main body, primary and secondary lids, basket and impact limiters. The main body has a sandwich-like wall with internal and external layers made of AISI 304 stainless steel with lead in-between. The lead provides biological shielding. The primary lid is similarly layered, but in the axial direction. It is provided with a double system of metallic rings and has ports for pressurization, sampling and containment verification. The secondary lid has the main function of protecting the primary lid against mechanical impacts. The basket structure is basically a tube array reinforced by bottom plate, feet and spacers. Square tubes are used for MTR elements and circular tubes for TRIGA elements. Finally, the impact limiters are structures made of an external stainless steel thin covering and a filling made of the wood composite OSB - Oriented Strand Board. The prototype is provided with bottom and top impact limiters, which are attached to each other by means of four threaded rods. The limiters are not rigidly attached to the cask body. A half scale cask model was designed to be submitted to a testing program. As its volume scales down to 1:8, the model weight is 1,250 kgf. This paper presents the methodology for the preliminary structural dimensioning of the critical parameters of the cask prototype. Both normal conditions of operation and hypothetical

  6. Brazilian minerals annual report

    International Nuclear Information System (INIS)

    1977-01-01

    Statistics of Brazilian mineral resources and production in 1977 are presented. Data included refer also to economic aspects, market, taxes, government incentives, manpower, exportation, importation, etc [pt

  7. Minerals industry survey, 1984

    Energy Technology Data Exchange (ETDEWEB)

    1984-01-01

    This is the seventh edition of the statistical survey commissioned by the Australian Mining Industry Council. It represents the most comprehensive review of the financial position of the Australian minerals industry and provides timely financial data on the minerals industry. The tables of this survey have been prepared for AMIC by Coopers and Lybrand, Chartered Accountants, based on information supplied to them in confidence by the respondent companies. For the purpose of the survey, the minerals industry has been defined as including exploration for, and extraction and primary processing of, minerals in Australia. The oil and gas industry is not included.

  8. Reagan issues mineral policy

    Science.gov (United States)

    The National Materials and Minerals Program plan and report that President Reagan sent to Congress on April 5 aims to ‘decrease America's minerals vulnerability’ while reducing future dependence on potentially unstable foreign sources of minerals. These goals would be accomplished by taking inventory of federal lands to determine mineral potential; by meeting the stockpile goals set by the Strategic and Critical Material Stockpiling Act; and by establishing a business and political climate that would encourage private-sector research and development on minerals.Now that the Administration has issued its plan, the Subcommittee on Mines and Mining of the House Committee on Interior and Insular Affairs will consider the National Minerals Security Act (NMSA), which was introduced 1 year ago by subcommittee chairman Jim Santini (D-Nev.) [Eos, May 19, 1981, p. 497]. The bill calls for establishing a three-member White-House-level council to coordinate the development of a national minerals policy; amending tax laws to assist the mining industry to make capital investments to locate and produce strategic materials; and creating a revolving fund for the sale and purchase of strategic minerals. In addition, the NMSA bill would allow the secretary of the interior to make previously withdrawn public lands available for mineral development. The subcommittee will hold a hearing on the Administration's plan on May 11. Interior Secretary James Watt has been invited to testify.

  9. International mineral economics

    International Nuclear Information System (INIS)

    Gocht, W.R.; Eggert, R.G.

    1988-01-01

    International Mineral Economics provides an integrated overview of the important concepts. The treatment is interdisciplinary, drawing on the fields of economics, geology, business, and mining engineering. Part I examines the technical concepts important for understanding the geology of ore deposits, the methods of exploration and deposit evaluation, and the activities of mining and mineral processing. Part II focuses on the economic and related concepts important for understanding mineral development, the evaluation of exploration and mining projects, and mineral markets and market models. Finally, Part III reviews and traces the historical development of the policies of international organizations, the industrialized countries, and the developing countries. (orig.)

  10. Mineral statistics yearbook 1994

    International Nuclear Information System (INIS)

    1994-01-01

    A summary of mineral production in Saskatchewan was compiled and presented as a reference manual. Statistical information on fuel minerals such as crude oil, natural gas, liquefied petroleum gas and coal, and of industrial and metallic minerals, such as potash, sodium sulphate, salt and uranium, was provided in all conceivable variety of tables. Production statistics, disposition and value of sales of industrial and metallic minerals were also made available. Statistical data on drilling of oil and gas reservoirs and crown land disposition were also included. figs., tabs

  11. Marine Mineral Exploration

    DEFF Research Database (Denmark)

    in EEZ areas are fairly unknown; many areas need detailed mapping and mineral exploration, and the majority of coastal or island states with large EEZ areas have little experience in exploration for marine hard minerals. This book describes the systematic steps in marine mineral exploration....... Such exploration requires knowledge of mineral deposits and models of their formation, of geophysical and geochemical exploration methods, and of data evaluation and interpretation methods. These topics are described in detail by an international group of authors. A short description is also given of marine...

  12. Prototype development of user specific climate services

    Science.gov (United States)

    Jacob, Daniela

    2017-04-01

    Systematic consultations in the last years with representatives from sectors particularly affected by climate change have helped the Climate Service Center Germany (GERICS) to identify the most pressing needs of stakeholders from public and private sectors. Besides the development of innovative climate service products and methods, areas are also identified, for which intensive research activities have to be initiated. An example is the demand of decision makers for high-resolution climate change information needed at regional to local levels for their activities towards climate change adaptation. For questions concerning adaptation to climate change, no standard solutions can be provided. Different from mitigation measures, adaptation measures must be framed in accordance with the specific circumstances prevailing in the local situation. Here, individual solutions, which satisfy the individual requirements and needs, are necessary. They have to be developed in close co-operation with the customers and users. For example, the implications of climate change on strategic and operative decisions, e.g. in enterprises and urban planning, are becoming increasingly important. Therefore, high-quality consultancy for businesses and public administration is needed, in order to support decision makers in identifying associated risks and opportunities. For the development of prototype products, GERICS has framed a general methodological approach, including the idea generation, the iterative development, and the prototype testing in co-development with the user. High process transparency and high product quality are prerequisite for the success of a product. The co-development process ensures the best possible communication of user tailored climate change information for different target groups.

  13. Minerals and Trace Elements Intakes and Food Consumption Patterns of Young Children Living in Rural Areas of Tibet Autonomous Region, P.R. China: A Cross-Sectional Survey

    Directory of Open Access Journals (Sweden)

    Michael Dermience

    2017-03-01

    Full Text Available Background and objectives: Several studies revealed clinical signs of stunting and rickets among rural populations of Tibet Autonomous Region (T.A.R., and especially amid children. Further, these populations are affected by a bone disease named Kashin-Beck disease (KBD. However, little is known about the dietary status of this population. This survey aimed to assess the usual intakes of young Tibetan children living in rural areas around Lhasa for energy, water, and ten minerals and trace elements (Na, K, Ca, P, Mg, Fe, Zn, Cu, Mn, and Se involved in bone metabolism. Design: A cross-sectional survey was designed. Totally, 250 pre-school children aged 3–5 years living in rural areas were enrolled. The 24-h food recall method was used to collect the intakes for two days, during two different seasons (September 2012 and April 2013. Because Tibetan foods are mainly derived from local agriculture and artisanal production, a combination of food composition tables was compiled, including specific and local food composition data. Results: The Chinese dietary recommended intakes are not met for most of the elements investigated. Intake of sodium is much too high, while usual intakes are too low for K, Ca, Zn, Cu, and Se. Bioavailability of Ca, Fe, and Zn may be of concern due to the high phytic acid content in the diet. Conclusion: These nutrient imbalances may impact growth and bone metabolism of young Tibetan children. The advantages of the implementation of food diversification programs are discussed as well as the relevance of supplements distribution.

  14. Minerals Yearbook, volume II, Area Reports—Domestic

    Science.gov (United States)

    ,

    2018-01-01

    The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

  15. Minerals Yearbook, volume III, Area Reports—International

    Science.gov (United States)

    ,

    2018-01-01

    The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

  16. Prototype moving-ring reactor

    International Nuclear Information System (INIS)

    Smith, A.C. Jr.; Ashworth, C.P.; Abreu, K.E.

    1982-01-01

    We have completed a design of the Prototype Moving-Ring Reactor. The fusion fuel is confined in current-carrying rings of magnetically-field-reversed plasma (Compact Toroids). The plasma rings, formed by a coaxial plasma gun, undergo adiabatic magnetic compression to ignition temperature while they are being injected into the reactor's burner section. The cylindrical burner chamber is divided into three burn stations. Separator coils and a slight axial guide field gradient are used to shuttle the ignited toroids rapidly from one burn station to the next, pausing for 1/3 of the total burn time at each station. D-T- 3 He ice pellets refuel the rings at a rate which maintains constant radiated power

  17. LEP vacuum chamber, early prototype

    CERN Multimedia

    CERN PhotoLab

    1978-01-01

    The structure of LEP, with long bending magnets and little access to the vacuum chamber between them, required distributed pumping. This is an early prototype for the LEP vacuum chamber, made from extruded aluminium. The main opening is for the beam. The small channel to the right is for cooling water, to carry away the heat deposited by the synchroton radiation from the beam. The 4 slots in the channel to the left house the strip-shaped ion-getter pumps (see 7810255). The ion-getter pumps depended on the magnetic field of the bending magnets, too low at injection energy for the pumps to function well. Also, a different design was required outside the bending magnets. This design was therefore abandoned, in favour of a thermal getter pump (see 8301153 and 8305170).

  18. Prototype international quality assurance program

    International Nuclear Information System (INIS)

    Broadway, J.A.; Chambless, D.A.; Sapozhnikov, Yu.A.; Kalmykov, S.N.

    1998-01-01

    The international community presently lacks the ability to determine the quality and credibility of environmental measurements that is required to make sound decisions in matters related to international security, public health, and investment-related considerations. The ultimate goal of the work described in this article is to develop a credible information base including measurement capability for determination of environmental contamination and the potential for proliferation of material components of chemical or nuclear weapons. This study compared the accuracy obtained by six Russian and six U.S. laboratories for samples representative of classes of trace metals, dioxing-furans, and radioactive substances. The results obtained in this work indicate that current estimates for laboratory accuracy are likely overly optimistic. The weaknesses discovered by this prototype U.S. - Russia study also exist within the broader international community of laboratories. Further work is proposed to address the urgent need for the international community to improve performance evaluations for analytical measurements. (author)

  19. Prototype of industrial electrons accelerator

    International Nuclear Information System (INIS)

    Lopez, V.H.; Valdovinos, A.M.

    1992-01-01

    The interest and the necessity of Mexico's industry in the use of irradiation process has been increased in the last years. As examples are the irradiation of combustion gases (elimination of NO x and SO 2 ) and the polymer cross-linking between others. At present time at least twelve enterprises require immediately of them which have been contacted by electron accelerators suppliers of foreign countries. The first project step consisted in to identify the electrons accelerator type that in can be constructed in Mexico with the major number of possible equipment, instruments, components and acquisition materials local and useful for the major number of users. the characteristics of the accelerator prototype are: accelerator type transformer with multiple secondary insulated and rectifier circuits with a potential of 0.8 MV of voltage, the second step it consisted in an economic study that permitted to demonstrate the economic feasibility of its construction. (Author)

  20. Hadron therapy information sharing prototype

    CERN Document Server

    Roman, Faustin Laurentiu; Kanellopoulos, Vassiliki; Amoros, Gabriel; Davies, Jim; Dosanjh, Manjit; Jena, Raj; Kirkby, Norman; Peach, Ken; Salt, Jose

    2013-01-01

    The European PARTNER project developed a prototypical system for sharing hadron therapy data. This system allows doctors and patients to record and report treatment-related events during and after hadron therapy. It presents doctors and statisticians with an integrated view of adverse events across institutions, using open-source components for data federation, semantics, and analysis. There is a particular emphasis upon semantic consistency, achieved through intelligent, annotated form designs. The system as presented is ready for use in a clinical setting, and amenable to further customization. The essential contribution of the work reported here lies in the novel data integration and reporting methods, as well as the approach to software sustainability achieved through the use of community-supported open-source components.

  1. PEP-II prototype klystron

    International Nuclear Information System (INIS)

    Fowkes, W.R.; Caryotakis, G.; Lee, T.G.; Pearson, C.; Wright, E.L.

    1993-04-01

    A 540-kW continuous-wave (cw) klystron operating at 476 MHz was developed for use as a power source for testing PEP-II rf accelerating cavities and rf windows. It also serves as a prototype for a 1.2 MW cw klystron presently being developed as a potential rf source for asymmetric colliding ring use. The design incorporates the concepts and many of the parts used in the original 353 MHz PEP klystron developed sixteen years ago. The superior computer simulation codes available today result in improved performance with the cavity frequencies, drift lengths, and output circuit optimized for the higher frequency.The design and operating results of this tube are described with particular emphasis on the factors which affect efficiency and stability

  2. The Yucca Mountain Project Prototype Testing Program

    International Nuclear Information System (INIS)

    1989-10-01

    The Yucca Mountain Project is conducting a Prototype Testing Program to ensure that the Exploratory Shaft Facility (ESF) tests can be completed in the time available and to develop instruments, equipment, and procedures so the ESF tests can collect reliable and representative site characterization data. This report summarizes the prototype tests and their status and location and emphasizes prototype ESF and surface tests, which are required in the early stages of the ESF site characterization tests. 14 figs

  3. Test case preparation using a prototype

    OpenAIRE

    Treharne, Helen; Draper, J.; Schneider, Steve A.

    1998-01-01

    This paper reports on the preparation of test cases using a prototype within the context of a formal development. It describes an approach to building a prototype using an example. It discusses how a prototype contributes to the testing activity as part of a lifecycle based on the use of formal methods. The results of applying the approach to an embedded avionics case study are also presented.

  4. A prototype for JDEM science data processing

    International Nuclear Information System (INIS)

    Gottschalk, Erik E

    2011-01-01

    Fermilab is developing a prototype science data processing and data quality monitoring system for dark energy science. The purpose of the prototype is to demonstrate distributed data processing capabilities for astrophysics applications, and to evaluate candidate technologies for trade-off studies. We present the architecture and technical aspects of the prototype, including an open source scientific execution and application development framework, distributed data processing, and publish/subscribe message passing for quality control.

  5. Rapid prototyping using CBCT: an initial experience

    International Nuclear Information System (INIS)

    Yovchev, D.; Deliverska, E.; Indjova, J.; Ugrinov, R.

    2011-01-01

    This report presents a case of fibrous dysplasia in the left lower jaw of a 12-year-old girl, scanned with CBCT. On the basis of CBCT scan a model of affected jaw was produced using a rapid-prototyping three-dimensional printer. The case demonstrates the possibility to get a prototype by CBCT data. Prototypes can be used to support the diagnosis, planning, training (students and postgraduates) and to obtain informed consent from the patient.

  6. Prototype calorimeters for the NA3 experiment

    CERN Multimedia

    1975-01-01

    The NA3 Experiment was set-up on the North Area of the SPS by the CERN/ Ecole Polytechnique/College de France/ Orsay/Saclay Collaboration, to study high transverse momentum leptons and hadrons from hadron collisions. The calorimeters measured the energy of hadrons (prototype on the right) and leptons (prototype on the left). They used a new type of plastic scintillator (plexipop). (see CERN Courier of November 1975) energy (prototype on the right)

  7. Non-compensation of the ATLAS barrel combined calorimeter prototype

    International Nuclear Information System (INIS)

    Kul'chitskij, Yu.A.; Kuz'min, M.V.

    1998-01-01

    The e / π ratio for the ATLAS Barrel Combined Calorimeter Prototype, composed from electromagnetic LArg calorimeter and hadronic Tile calorimeter was investigated. Response of Combined Calorimeter on pions and electrons in the energy region of 20-300 GeV was studied. Found e / h = 1.37 ± 0.01 ± 0.02 is in good agreement with the results from previous Combined Calorimeter tests but has more precisions

  8. Mineral oil industry

    NARCIS (Netherlands)

    Brasser, L.J.; Suess, M.J.; Grefen, K.; Reinisch, D.W.

    1985-01-01

    In this chapter a general picture is presented of the air pollution aspects in the mineral oil industry. The complete field is covered, starting from drilling operations and the well head up to the delivery of the products to the consumer. A large field of activities as is given by the mineral oil

  9. Vitamins, Minerals, and Mood

    Science.gov (United States)

    Kaplan, Bonnie J.; Crawford, Susan G.; Field, Catherine J.; Simpson, J. Steven A.

    2007-01-01

    In this article, the authors explore the breadth and depth of published research linking dietary vitamins and minerals (micronutrients) to mood. Since the 1920s, there have been many studies on individual vitamins (especially B vitamins and Vitamins C, D, and E), minerals (calcium, chromium, iron, magnesium, zinc, and selenium), and vitamin-like…

  10. Mineral commodity summaries 2018

    Science.gov (United States)

    Ober, Joyce A.

    2018-01-31

    This report is the earliest Government publication to furnish estimates covering 2017 nonfuel mineral industry data. Data sheets contain information on the domestic industry structure, Government programs, tariffs, and 5-year salient statistics for more than 90 individual minerals and materials.

  11. Indochina area mineral prospects

    Energy Technology Data Exchange (ETDEWEB)

    1990-10-05

    Prospects for commercial mining of various minerals are considered for Kampuchea (Cambodia), Laos, Vietnam, Myanmar (Burma) and Thailand. Mineral production is much below its geologic potential for economic and political reasons. Resource potential is limited to tin, tungsten, lead and zinc, barytes and gemstones, and coal. 1 fig.

  12. Taxation of unmined minerals

    International Nuclear Information System (INIS)

    Bremberg, B.P.

    1989-01-01

    This paper reports on the Kentucky Revenue Cabinet which began implementing its controversial unmined minerals tax program. The Revenue Cabinet should complete its first annual assessment under this program in December, 1989. The Revenue Cabinet's initial efforts to collect basic data concerning the Commonwealth's coal bearing lands has yielded data coverage for 5 million of Kentucky's 10 million acres of coal lands. Approximately 1000 detailed information returns have been filed. The returns will be used to help create an undeveloped mineral reserves inventory, determine mineral ownership, and value mineral reserves. This new program is run by the Revenue Cabinet's Mineral Valuation Section, under the Division of Technical Support, Department of Property Taxation. It has been in business since September of 1988

  13. Mineral industry in Australia

    International Nuclear Information System (INIS)

    Parbo, S.A.

    1982-01-01

    The paper reviews the history and growth of the mineral industry in Australia and its significance to the nation's economic growth and overseas trade, particularly over the last twenty years during which time production of coal, iron ore, manganese and mineral sands has increased greatly and new discoveries of petroleum, bauxite and nickel have given rise to major new industries. Australia ranks fourteenths in the value of world trade and is among the world's largest exporters of alumina, iron ore, mineral sands, coal, lead, zinc and nickel. Some details of production, processing and exports of the major minerals are given. Comment is made on the policies and roles of the six State Governments and the Federal Government in respect of ownership and control of the mining, processing and exporting of both energy and non-energy minerals. (orig.) [de

  14. Evaluation of the Sentinel-3 Hydrologic Altimetry Processor prototypE (SHAPE) methods.

    Science.gov (United States)

    Benveniste, J.; Garcia-Mondéjar, A.; Bercher, N.; Fabry, P. L.; Roca, M.; Varona, E.; Fernandes, J.; Lazaro, C.; Vieira, T.; David, G.; Restano, M.; Ambrózio, A.

    2017-12-01

    Inland water scenes are highly variable, both in space and time, which leads to a much broader range of radar signatures than ocean surfaces. This applies to both LRM and "SAR" mode (SARM) altimetry. Nevertheless the enhanced along-track resolution of SARM altimeters should help improve the accuracy and precision of inland water height measurements from satellite. The SHAPE project - Sentinel-3 Hydrologic Altimetry Processor prototypE - which is funded by ESA through the Scientific Exploitation of Operational Missions Programme Element (contract number 4000115205/15/I-BG) aims at preparing for the exploitation of Sentinel-3 data over the inland water domain. The SHAPE Processor implements all of the steps necessary to derive rivers and lakes water levels and discharge from Delay-Doppler Altimetry and perform their validation against in situ data. The processor uses FBR CryoSat-2 and L1A Sentinel-3A data as input and also various ancillary data (proc. param., water masks, L2 corrections, etc.), to produce surface water levels. At a later stage, water level data are assimilated into hydrological models to derive river discharge. This poster presents the improvements obtained with the new methods and algorithms over the regions of interest (Amazon and Danube rivers, Vanern and Titicaca lakes).

  15. A new prototype for the PANDA disc DIRC detector

    Energy Technology Data Exchange (ETDEWEB)

    Rieke, Julian; Dueren, Michael; Hayrapetyan, Avetik; Foehl, Klaus; Kroeck, Benno; Merle, Oliver; Etzelmueller, Erik; Biguenko, Klim [Justus Liebig Universitaet, Giessen (Germany); Collaboration: PANDA-Collaboration

    2014-07-01

    The PANDA experiment at the future FAIR facility needs excellent particle identification to do precision studies of antiproton-proton reactions in the 1.5-15 GeV/c momentum range. To fulfill this need, two Cherenkov detectors will be installed in the PANDA target spectrometer, both based on the DIRC concept that uses internally reflected Cherenkov light to perform particle identification, with a focus on the separation of pions and kaons. The Disc-DIRC is designed to cap the forward region of theta angles between 5 and 22 degrees. It will be the first time that a 3D-Disc-DIRC is used for PID in a real physics experiment beyond prototyping. A new prototyping Disc-DIRC apparatus has been constructed at the JLU Giessen. Unlike previous prototypes, this one features a radiator as well as focusing elements made out of fused silica. The Cherenkov light is detected with 22 multi-anode-phototubes and 4 MCP-PMTs, totalling 608 individual pixels. Timing information for each of the latter is generated using the novel TRB3 system developed at GSI. The entire prototype was tested with an electron beam of several GeV/c provided by DESY in Hamburg. The components, their setup and a first analysis of the recorded data will be presented.

  16. Heavy mineral concentration from oil sand tailings

    Energy Technology Data Exchange (ETDEWEB)

    Chachula, F.; Erasmus, N. [Titanium Corp. Inc., Regina, SK (Canada)

    2008-07-01

    This presentation described a unique technique to recover heavy minerals contained in the froth treatment tailings produced by oil sand mining extraction operations in Fort McMurray, Alberta. In an effort to process waste material into valuable products, Titanium Corporation is developing technology to recover heavy minerals, primarily zircon, and a portion of bitumen contained in the final stage of bitumen processing. The process technology is being developed to apply to all mined oil sands operations in the Fort McMurray region. In 2004, Titanium Corporation commissioned a pilot research facility at the Saskatchewan Research Council to test dry oil sands tailings. In 2005, a bulk sampling pilot plant was connected to the fresh oil sands tailings pipeline on-site in Fort McMurray, where washed sands containing heavy minerals were processed at a pilot facility. The mineral content in both deposited tailings and fresh pipeline tailings was assessed. Analysis of fresh tailings on a daily basis identified a constant proportion of zircon and higher levels of associated bitumen compared with the material in the deposited tailings. The process flow sheet design was then modified to remove bitumen from the heavy minerals and concentrate the minerals. A newly modified flotation process was shown to be a viable processing route to recover the heavy minerals from froth treatment tailings. 8 refs., 9 tabs., 12 figs.

  17. Alteration geochemistry of the volcanic-hosted Dedeninyurdu, Yergen and Fındıklıyar Fe-Cu mineralization at Gökçedoǧan, Çorum-Kargi region, Turkey

    Science.gov (United States)

    Gumus, Lokman; Öztürk, Sercan; Yalçın, Cihan; Abdelnasser, Amr; Hanilçi, Nurullah; Kumral, Mustafa

    2016-04-01

    This study is to determine the mass/volume gain and loss of the major and trace elements during the alteration processes on Dedeninyurdu, Yergen and Fındıklıyar Fe-Cu mineralizations of the area. Fe-Cu mineralization occurred in the spilitic volcanic a rock of Saraycık Formation is associated with the different types of alteration zones which are pyritization, silicification and sericitization. The study area comprises Bekirli Formation, Saraycık Formation, Beşpınar Formation, and Ilgaz Formation. Saraycık formation consists of spilitic volcanic rocks with pelagic limestone, siltstone and chert. The ore mineralogical data show that the pyrite, chalcopyrite, covellite, hematite, malachite and goethite formed during three phases of mineralization. As well as the geologic and petrographic studies reveal three alteration zones with definite mineral assemblages; phyllic alteration (quartz + sericite + pyrite) that represents the main alteration and mineralized zone; propylitic alteration; and carbonatized sericitic alteration zone. The boundaries between these zones are gradual. Mass balance calculations suggested that the phyllic alteration zone represented by gain in Si, Fe, K, S, and LOI and loss in Mg, Ca, and Na refers to silicification, sericitization and pyritization as well as replacement of Fe-Mg silicate and plagioclase. While, in the propylitic alteration zone, enrichment of Si, Fe, Mg, LOI and S occurred with depletions of Ca, Na, and K reflecting chloritization alteration type. On the other hand, carbonatized sericitic alteration zone shows local gain in Si, CaO and K reflects the occurrence of calc-silicate alteration. All alteration zones contain a large proportion of sulfide minerals (gain in S) with increase in loss on ignition (LOI). Keywords: Alteration geochemistry; Mass balance calculation, Fe-Cu mineralization; phyllic alteration, propylitic alteration.

  18. Enhancing experience prototyping by the help of mixed-fidelity prototypes

    OpenAIRE

    Yasar, Ansar-Ul-Haque

    2007-01-01

    In this research review I undertook the problem related to the usage of a new concept known as the Mixed- Fidelity Prototype which is a mixture of its predecessors Low- and High- Fidelity Prototypes in Experience Prototyping. Experience Prototyping is a good way to explore, communicate and interact with the designs we develop like experiencing cycling on the ice, although the mood, snow conditions, bicycle type and many other factors really matter and tend to change with time. Experience Prot...

  19. Statistical models for optimizing mineral exploration

    International Nuclear Information System (INIS)

    Wignall, T.K.; DeGeoffroy, J.

    1987-01-01

    The primary purpose of mineral exploration is to discover ore deposits. The emphasis of this volume is on the mathematical and computational aspects of optimizing mineral exploration. The seven chapters that make up the main body of the book are devoted to the description and application of various types of computerized geomathematical models. These chapters include: (1) the optimal selection of ore deposit types and regions of search, as well as prospecting selected areas, (2) designing airborne and ground field programs for the optimal coverage of prospecting areas, and (3) delineating and evaluating exploration targets within prospecting areas by means of statistical modeling. Many of these statistical programs are innovative and are designed to be useful for mineral exploration modeling. Examples of geomathematical models are applied to exploring for six main types of base and precious metal deposits, as well as other mineral resources (such as bauxite and uranium)

  20. Mineral facilities of Europe

    Science.gov (United States)

    Almanzar, Francisco; Baker, Michael S.; Elias, Nurudeen; Guzman, Eric

    2010-01-01

    This map displays over 1,700 records of mineral facilities within the countries of Europe and western Eurasia. Each record represents one commodity and one facility type at a single geographic location. Facility types include mines, oil and gas fields, and plants, such as refineries, smelters, and mills. Common commodities of interest include aluminum, cement, coal, copper, gold, iron and steel, lead, nickel, petroleum, salt, silver, and zinc. Records include attributes, such as commodity, country, location, company name, facility type and capacity (if applicable), and latitude and longitude geographical coordinates (in both degrees-minutes-seconds and decimal degrees). The data shown on this map and in table 1 were compiled from multiple sources, including (1) the most recently available data from the U.S. Geological Survey (USGS) Minerals Yearbook (Europe and Central Eurasia volume), (2) mineral statistics and information from the USGS Minerals Information Web site (http://minerals.usgs.gov/minerals/pubs/country/europe.html), and (3) data collected by the USGS minerals information country specialists from sources, such as statistical publications of individual countries, annual reports and press releases of operating companies, and trade journals. Data reflect the most recently published table of industry structure for each country at the time of this publication. Additional information is available from the country specialists listed in table 2.

  1. Prototyping SOS meta-theory in Maude

    NARCIS (Netherlands)

    Mousavi, M.R.; Reniers, M.A.; Mosses, P.D.; Ulidowski, I.

    2006-01-01

    We present a prototype implementation of SOS meta-theory in the Maude term rewriting language. The prototype defines the basic concepts of SOS meta-theory (e.g., transition formulae, deduction rules and transition system specifications) in Maude. Besides the basic definitions, we implement methods

  2. OPAL jet chamber full-scale prototype

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, H M; Hauschild, M; Hartmann, H; Hegerath, A; Boerner, H; Burckhart, H J; Dittmar, M; Hammarstroem, R; Heuer, R D; Mazzone, L

    1986-12-01

    The concept of a jet chamber for the central detector of OPAL was tested with a full scale prototype. The design of this prototype, its mechanical and electrical structure and its support system for high voltage, gas, laser calibration, and readout are described. Operating experience was gathered since summer 1984. The chamber performance in terms of spatial resolution and particle identification capability is given.

  3. Gamification in a Prototype Household Energy Game

    NARCIS (Netherlands)

    Fijnheer, J.D.L.; van Oostendorp, H.; Veltkamp, R.C.

    2016-01-01

    Research where gamification is used to influence household energy consumption is an emerging field. This paper reviews design features of the prototype Powersaver Game. The aim of this game is to influence household energy consumption in the long-term. The evaluation of the design of the prototype,

  4. Rapid Prototyping in Instructional Design: Creating Competencies

    Science.gov (United States)

    Fulton, Carolyn D.

    2010-01-01

    Instructional designers working in rapid prototyping environments currently do not have a list of competencies that help to identify the knowledge, skills, and attitudes (KSAs) required in these workplaces. This qualitative case study used multiple cases in an attempt to identify rapid prototyping competencies required in a rapid prototyping…

  5. Definitions of Health Terms: Minerals

    Science.gov (United States)

    ... gov/definitions/mineralsdefinitions.html Definitions of Health Terms : Minerals To use the sharing features on this page, ... National Institutes of Health, Office of Dietary Supplements Minerals Minerals are those elements on the earth and ...

  6. Minerals industry survey 1987

    Energy Technology Data Exchange (ETDEWEB)

    1987-01-01

    This is the eleventh Minerals Industry Survey produced by the Australian Mining Industry Council. It represents an invaluable time series on the minerals industry's financial performance, as well as an up to date description of the industry for the latest financial year. The survey has been conceived as a supplement to and expansion of the various Australian Bureau of Statistics and Bureau of Mineral Resources, Geology and Geophysics publications which describe the exploration, mining and smelting and refining industries in Australia. The tables in this survey have been prepared by Coopers and Lybrand, Chartered Accountants, based on information supplied to them in confidence by the respondent companies.

  7. Dissipative Prototyping Methods: A Manifesto

    Science.gov (United States)

    Beesley, P.

    Taking a designer's unique perspective using examples of practice in experimental installation and digital protoyping, this manifesto acts as provocation for change and unlocking new potential by encouraging changes of perspective about the material realm. Diffusive form-language is proposed as a paradigm for architectural design. This method of design is applied through 3D printing and related digital fabrication methods, offering new qualities that can be implemented in design of realms including present earth and future interplanetary environments. A paradigm shift is encouraged by questioning conventional notions of geometry that minimize interfaces and by proposing the alternatives of maximized interfaces formed by effusive kinds of formal composition. A series of projects from the Canadian research studio of the Hylozoic Architecture group are described, providing examples of component design methods employing diffusive forms within combinations of tension-integrity structural systems integrated with hybrid metabolisms employing synthetic biology. Cultural implications are also discussed, drawing from architectural theory and natural philosophy. The conclusion of this paper suggests that the practice of diffusive prototyping can offer formative strategies contributing to design of future living systems.

  8. A French fuel cell prototype

    International Nuclear Information System (INIS)

    Anon.

    2001-01-01

    A French prototype of a fuel cell based on the PEM (proton exchange membrane) technology has been designed by Helion, a branch of Technicatome, this fuel cell delivers 300 kW and will be used in naval applications and terrestrial transport. The main advantages of fuel cell are: 1) no contamination, even if the fuel used is natural gas the quantities of CO 2 and CO emitted are respectively 17 and 75 times as little as the maximal quantities allowed by European regulations, 2) efficiency, the electric yield is up to 60 % and can reach 80 % if we include the recovery of heat, 3) silent, the fuel cell itself does not make noise. The present price of fuel cell is the main reason that hampers its industrial development, this price is in fact strongly dependant on the cost of its different components: catalyzers, membranes, bipolar plates and the hydrogen supply. This article gives the technical characteristics of the Helion's fuel cell. (A.C.)

  9. Wireless Augmented Reality Prototype (WARP)

    Science.gov (United States)

    Devereaux, A. S.

    1999-01-01

    Initiated in January, 1997, under NASA's Office of Life and Microgravity Sciences and Applications, the Wireless Augmented Reality Prototype (WARP) is a means to leverage recent advances in communications, displays, imaging sensors, biosensors, voice recognition and microelectronics to develop a hands-free, tetherless system capable of real-time personal display and control of computer system resources. Using WARP, an astronaut may efficiently operate and monitor any computer-controllable activity inside or outside the vehicle or station. The WARP concept is a lightweight, unobtrusive heads-up display with a wireless wearable control unit. Connectivity to the external system is achieved through a high-rate radio link from the WARP personal unit to a base station unit installed into any system PC. The radio link has been specially engineered to operate within the high- interference, high-multipath environment of a space shuttle or space station module. Through this virtual terminal, the astronaut will be able to view and manipulate imagery, text or video, using voice commands to control the terminal operations. WARP's hands-free access to computer-based instruction texts, diagrams and checklists replaces juggling manuals and clipboards, and tetherless computer system access allows free motion throughout a cabin while monitoring and operating equipment.

  10. Virtual Video Prototyping of Pervasive Healthcare Systems

    DEFF Research Database (Denmark)

    Bardram, Jakob Eyvind; Bossen, Claus; Madsen, Kim Halskov

    2002-01-01

    Virtual studio technology enables the mixing of physical and digital 3D objects and thus expands the way of representing design ideas in terms of virtual video prototypes, which offers new possibilities for designers by combining elements of prototypes, mock-ups, scenarios, and conventional video....... In this article we report our initial experience in the domain of pervasive healthcare with producing virtual video prototypes and using them in a design workshop. Our experience has been predominantly favourable. The production of a virtual video prototype forces the designers to decide very concrete design...... issues, since one cannot avoid paying attention to the physical, real-world constraints and to details in the usage-interaction between users and technology. From the users' perspective, during our evaluation of the virtual video prototype, we experienced how it enabled users to relate...

  11. Virtual Video Prototyping for Healthcare Systems

    DEFF Research Database (Denmark)

    Bardram, Jakob Eyvind; Bossen, Claus; Lykke-Olesen, Andreas

    2002-01-01

    Virtual studio technology enables the mixing of physical and digital 3D objects and thus expands the way of representing design ideas in terms of virtual video prototypes, which offers new possibilities for designers by combining elements of prototypes, mock-ups, scenarios, and conventional video....... In this article we report our initial experience in the domain of pervasive healthcare with producing virtual video prototypes and using them in a design workshop. Our experience has been predominantly favourable. The production of a virtual video prototype forces the designers to decide very concrete design...... issues, since one cannot avoid paying attention to the physical, real-world constraints and to details in the usage-interaction between users and technology. From the users' perspective, during our evaluation of the virtual video prototype, we experienced how it enabled users to relate...

  12. High confidence in falsely recognizing prototypical faces.

    Science.gov (United States)

    Sampaio, Cristina; Reinke, Victoria; Mathews, Jeffrey; Swart, Alexandra; Wallinger, Stephen

    2018-06-01

    We applied a metacognitive approach to investigate confidence in recognition of prototypical faces. Participants were presented with sets of faces constructed digitally as deviations from prototype/base faces. Participants were then tested with a simple recognition task (Experiment 1) or a multiple-choice task (Experiment 2) for old and new items plus new prototypes, and they showed a high rate of confident false alarms to the prototypes. Confidence and accuracy relationship in this face recognition paradigm was found to be positive for standard items but negative for the prototypes; thus, it was contingent on the nature of the items used. The data have implications for lineups that employ match-to-suspect strategies.

  13. Radioactive minerals - Multimedias strategies for their divulgation

    Science.gov (United States)

    Cabral, João; Gomes, Ana; Aldano, Ana; Fonseca, Pedro; Cabral, Tiago; Nobre, José

    2014-05-01

    The region corresponding to Sortelha-Penalobo - Bendada, located deep in the transition zone between the Hesperian massif and the Cova da Beira in the central part of Portugal, more specifically in the Mountainous region of the province of Beira Alta, county Sabugal. This region is characterized by great mineral wealth combined with geomorphology of recognized landscape value. Under the scientific point of view, this region is the origin of the mineral sabugalite (HAl(UO2)4(PO4)4.16H2O) that was described by the famous American mineralogist Clifford Frondel (1907-2002) in the fifties of the 20th century. Uranium minerals of Sabugal region were also associated with the radioactivity studies made by the well-known French physicist Marie Curie (1867-1934). In 2007, U. Kolitsch et al described the Bendadaite (Fe (AsO4) 2 (OH) 2 • 4H2O), which corresponds to a new mineral from the group arthurite. The mineral wealth of this region is responsible for a rich history of mining and to highlight the importance until the 1990s the extraction of uranium minerals. The main uranium minerals extracted were the tobernite (Cu (UO2) 2 (PO4) 2 • 12 H2O), the metatobernite (Cu (UO2) 2 (PO4) 2 • 8 H 2 O), the autonite (Ca (UO2) 2 (PO4 ) 2 • 12H2O-10) and sabugalite (HAL (UO2) 4 (PO4) 4 16H2O). Due to the high radioactivity of these minerals, their handling becomes infeasible for disclosure purposes. An integrated and multidisciplinary museological strategy aims to access 3D images by QR codes, using multitouch as the primary means of interaction with the user, and can handle even the virtual samples, access various magnifications and enjoy explanations supplied by a mascot, in a fun way. All this framework and geological environment becomes an asset for the scientific, educational and economic development of the region. On the other hand, it has a vital importance in the context of a strategy of forming a geological park, in the point of view of tourism, research and

  14. Características generales del campo mineral aurífero aguas claras en el contexto geológico regional de la provincia Holguín, Cuba

    OpenAIRE

    Costafreda Mustelier, Jorge Luis

    1996-01-01

    El Campo Mineral Aurífero de Aguas Claras se ubica al norte de Holguín, en una franja alargada de unos 15 kilómetros de longitud. Dentro de este campo mineral se encuentran cuatro minas principales: Nuevo Potosí: Formado por 3 tres cuerpos minerales en forma venas y diseminaciones auríferas (55.783 tn), espesor promedio es de 1,06 metros, contenido medio 7,89 g/t de Au y reserva de metal de 440,0 Kg. Agrupada: La mineralización aparece en venas de hasta 1.0 metro de espe...

  15. Law of radioactive minerals

    International Nuclear Information System (INIS)

    1980-01-01

    Legal device done in order to standardize and promote the exploration and explotation of radioactive minerals by peruvian and foreign investors. This device include the whole process, since the prospection until the development, after previous auction given by IPEN

  16. Mineral Commodity Summaries 2009

    Science.gov (United States)

    ,

    2009-01-01

    Each chapter of the 2009 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2008 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses. For mineral commodities for which there is a Government stockpile, detailed information concerning the stockpile status is included in the two-page synopsis. Because specific information concerning committed inventory was no longer available from the Defense Logistics Agency, National Defense Stockpile Center, that information, which was included in earlier Mineral Commodity Summaries publications, has been deleted from Mineral Commodity Summaries 2009. National reserves and reserve base information for most mineral commodities found in this report, including those for the United States, are derived from a variety of sources. The ideal source of such information would be comprehensive evaluations that apply the same criteria to deposits in different geographic areas and report the results by country. In the absence of such evaluations, national reserves and reserve base estimates compiled by countries for selected mineral commodities are a primary source of national reserves and reserve base information. Lacking national assessment information by governments, sources such as academic articles, company reports, common business practice, presentations by company representatives, and trade journal articles, or a combination of these, serve as the basis for national reserves and reserve base information reported in the mineral commodity sections of this publication. A national estimate may be assembled from the following: historically reported

  17. sequenceMiner algorithm

    Data.gov (United States)

    National Aeronautics and Space Administration — Detecting and describing anomalies in large repositories of discrete symbol sequences. sequenceMiner has been open-sourced! Download the file below to try it out....

  18. Calderas and mineralization: volcanic geology and mineralization in the Chianti caldera complex, Trans-Pecos Texas

    Energy Technology Data Exchange (ETDEWEB)

    Duex, T.W.; Henry, C.D.

    1981-01-01

    This report describes preliminary results of an ongoing study of the volcanic stratigraphy, caldera activity, and known and potential mineralization of the Chinati Mountains area of Trans-Pecos Texas. Many ore deposits are spatially associated with calderas and other volcanic centers. A genetic relationship between calderas and base and precious metal mineralization has been proposed by some and denied by others. Steven and others have demonstrated that calderas provide an important setting for mineralization in the San Juan volcanic field of Colorado. Mineralization is not found in all calderas but is apparently restricted to calderas that had complex, postsubsidence igneous activity. A comparison of volcanic setting, volcanic history, caldera evolution, and evidence of mineralization in Trans-Pecos to those of the San Juan volcanic field, a major mineral producer, indicates that Trans-Pecos Texas also could be an important mineralized region. The Chianti caldera complex in Trans-Pecos Texas contains at least two calderas that have had considerable postsubsidence activity and that display large areas of hydrothermal alteration and mineralization. Abundant prospects in Trans-Pecos and numerous producing mines immediately south of the Trans-Pecos volcanic field in Mexico are additional evidence that ore-grade deposits could occur in Texas.

  19. Mineral industry statistics 1975

    Energy Technology Data Exchange (ETDEWEB)

    1978-01-01

    Production, consumption and marketing statistics are given for solid fuels (coal, peat), liquid fuels and gases (oil, natural gas), iron ore, bauxite and other minerals quarried in France, in 1975. Also accident statistics are included. Production statistics are presented of the Overseas Departments and territories (French Guiana, New Caledonia, New Hebrides). An account of modifications in the mining field in 1975 is given. Concessions, exploitation permits, and permits solely for prospecting for mineral products are discussed. (In French)

  20. Coastal placer minerals

    Digital Repository Service at National Institute of Oceanography (India)

    Iyer, S.D.; Gujar, A.R.

    to be processed and purified to extract the metal either by sulphate or chloride route. The economical aspects of placer mining would involve the cost to benefit ratio, which would encompass the money Selective sorting has resulted in two distinct sediments... or mineral at the national and international levels. Interestingly, though gold is the most sought metal and the prices per gram keep rising, there are others that are much more costly such as diamond and rare earth metals. Uses of Heavy Minerals...

  1. [Pneumoconiosis in bauxite miners].

    Science.gov (United States)

    Molinini, R; Pesola, M; Digennaro, M A; Carino, M; Nuzzaco, A; Coviello, F

    1985-01-01

    The authors examined a group of 40 miners who were being working at an Apulian bauxite mine, presently inactive. Radiographic findings of pulmonary micronodulation without significant reduction of lung functions were showed in 15 miners. Mineralogical analysis of mine dust samples excluded any presence of more than 1% free silica. As a result of this study hypotheses have been formulated about pathogenesis of this moderated and non-invasive pneumoconiosis, showed in long exposed subjects to low silica content dusts.

  2. OPAQUE MINERAL CONTENT OF DUTLUCA VOLCANICS (BURHANİYE - BALIKESİR: THE EFFECT OF HYDROTHERMAL ALTERATION ON THESE MINERALS

    Directory of Open Access Journals (Sweden)

    Şükrü KOÇ

    2016-12-01

    Full Text Available Dutluca volcanics, which are known as Hallaçlar Formation in regional scale in the study area (Kurshens- ky, 1976, are composed of hydrothermally altered andesite and basaltic andesite. In these rocks, sulfidic minerals such as pyrite, enargite and chalcosine, and oxide and hydroxide minerals such as magnetite, hematite and goethite were detected as opaque minerals. The presence of enargite in opaque mineral para- genesis, and the changes observed in structures and textures of opaque and silicate minerals indicate that examined volcanics have been altered by highly sulfidic hydrothermal solutions. During the hydrothermal alteration process, which indicates at least in two phases, a diffuse pyritization rich in H S in reducing conditions and enargite mineral, which is known as pathfinder minerals in such processes, formed in the first phase. Later on; the extensive martitization developed in oxidizing conditions.

  3. Mineral commodity summaries 2013

    Science.gov (United States)

    ,

    2013-01-01

    Each chapter of the 2013 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2012 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses. For mineral commodities for which there is a Government stockpile, detailed information concerning the stockpile status is included in the two-page synopsis. Abbreviations and units of measure, and definitions of selected terms used in the report, are in Appendix A and Appendix B, respectively. “Appendix C—Reserves and Resources” includes “Part A—Resource/Reserve Classification for Minerals” and “Part B—Sources of Reserves Data.” A directory of USGS minerals information country specialists and their responsibilities is Appendix D. The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the MCS 2013 are welcomed.

  4. Mineral commodity summaries 2014

    Science.gov (United States)

    ,

    2014-01-01

    Each chapter of the 2014 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2013 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses. For mineral commodities for which there is a Government stockpile, detailed information concerning the stockpile status is included in the two-page synopsis. Abbreviations and units of measure, and definitions of selected terms used in the report, are in Appendix A and Appendix B, respectively. “Appendix C—Reserves and Resources” includes “Part A—Resource/Reserve Classification for Minerals” and “Part B—Sources of Reserves Data.” A directory of USGS minerals information country specialists and their responsibilities is Appendix D. The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the MCS 2014 are welcomed.

  5. Prototype-Incorporated Emotional Neural Network.

    Science.gov (United States)

    Oyedotun, Oyebade K; Khashman, Adnan

    2017-08-15

    Artificial neural networks (ANNs) aim to simulate the biological neural activities. Interestingly, many ''engineering'' prospects in ANN have relied on motivations from cognition and psychology studies. So far, two important learning theories that have been subject of active research are the prototype and adaptive learning theories. The learning rules employed for ANNs can be related to adaptive learning theory, where several examples of the different classes in a task are supplied to the network for adjusting internal parameters. Conversely, the prototype-learning theory uses prototypes (representative examples); usually, one prototype per class of the different classes contained in the task. These prototypes are supplied for systematic matching with new examples so that class association can be achieved. In this paper, we propose and implement a novel neural network algorithm based on modifying the emotional neural network (EmNN) model to unify the prototype- and adaptive-learning theories. We refer to our new model as ``prototype-incorporated EmNN''. Furthermore, we apply the proposed model to two real-life challenging tasks, namely, static hand-gesture recognition and face recognition, and compare the result to those obtained using the popular back-propagation neural network (BPNN), emotional BPNN (EmNN), deep networks, an exemplar classification model, and k-nearest neighbor.

  6. Rapid prototyping and stereolithography in dentistry

    Science.gov (United States)

    Nayar, Sanjna; Bhuminathan, S.; Bhat, Wasim Manzoor

    2015-01-01

    The word rapid prototyping (RP) was first used in mechanical engineering field in the early 1980s to describe the act of producing a prototype, a unique product, the first product, or a reference model. In the past, prototypes were handmade by sculpting or casting, and their fabrication demanded a long time. Any and every prototype should undergo evaluation, correction of defects, and approval before the beginning of its mass or large scale production. Prototypes may also be used for specific or restricted purposes, in which case they are usually called a preseries model. With the development of information technology, three-dimensional models can be devised and built based on virtual prototypes. Computers can now be used to create accurately detailed projects that can be assessed from different perspectives in a process known as computer aided design (CAD). To materialize virtual objects using CAD, a computer aided manufacture (CAM) process has been developed. To transform a virtual file into a real object, CAM operates using a machine connected to a computer, similar to a printer or peripheral device. In 1987, Brix and Lambrecht used, for the first time, a prototype in health care. It was a three-dimensional model manufactured using a computer numerical control device, a type of machine that was the predecessor of RP. In 1991, human anatomy models produced with a technology called stereolithography were first used in a maxillofacial surgery clinic in Viena. PMID:26015715

  7. Rapid prototyping and stereolithography in dentistry.

    Science.gov (United States)

    Nayar, Sanjna; Bhuminathan, S; Bhat, Wasim Manzoor

    2015-04-01

    The word rapid prototyping (RP) was first used in mechanical engineering field in the early 1980s to describe the act of producing a prototype, a unique product, the first product, or a reference model. In the past, prototypes were handmade by sculpting or casting, and their fabrication demanded a long time. Any and every prototype should undergo evaluation, correction of defects, and approval before the beginning of its mass or large scale production. Prototypes may also be used for specific or restricted purposes, in which case they are usually called a preseries model. With the development of information technology, three-dimensional models can be devised and built based on virtual prototypes. Computers can now be used to create accurately detailed projects that can be assessed from different perspectives in a process known as computer aided design (CAD). To materialize virtual objects using CAD, a computer aided manufacture (CAM) process has been developed. To transform a virtual file into a real object, CAM operates using a machine connected to a computer, similar to a printer or peripheral device. In 1987, Brix and Lambrecht used, for the first time, a prototype in health care. It was a three-dimensional model manufactured using a computer numerical control device, a type of machine that was the predecessor of RP. In 1991, human anatomy models produced with a technology called stereolithography were first used in a maxillofacial surgery clinic in Viena.

  8. Review on CNC-Rapid Prototyping

    International Nuclear Information System (INIS)

    M Nafis O Z; Nafrizuan M Y; Munira M A; Kartina J

    2012-01-01

    This article reviewed developments of Computerized Numerical Control (CNC) technology in rapid prototyping process. Rapid prototyping (RP) can be classified into three major groups; subtractive, additive and virtual. CNC rapid prototyping is grouped under the subtractive category which involves material removal from the workpiece that is larger than the final part. Richard Wysk established the use of CNC machines for rapid prototyping using sets of 2½-D tool paths from various orientations about a rotary axis to machine parts without refixturing. Since then, there are few developments on this process mainly aimed to optimized the operation and increase the process capabilities to stand equal with common additive type of RP. These developments include the integration between machining and deposition process (hybrid RP), adoption of RP to the conventional machine and optimization of the CNC rapid prototyping process based on controlled parameters. The article ended by concluding that the CNC rapid prototyping research area has a vast space for improvement as in the conventional machining processes. Further developments and findings will enhance the usage of this method and minimize the limitation of current approach in building a prototype.

  9. Evaluation of a prototype infrasound system

    International Nuclear Information System (INIS)

    Whitaker, R.; Sandoval, T.; Breding, D.; Kromer, D.

    1997-01-01

    Under Department of Energy sponsorship, Sandia National Laboratories and Los Alamos National Laboratory cooperated to develop a prototype infrasonic array, with associated documentation, that could be used as part of the International Monitoring System. The United States Government or foreign countries could procure commercially available systems based on this prototype to fulfill their Comprehensive Test Ban Treaty (CTBT) obligations. The prototype is a four-element array in a triangular layout as recommended in CD/NTB/WP.224 with an element at each corner and one in the center. The prototype test configuration utilize an array spacing of 1 km. The prototype infrasound system has the following objectives: (1) Provide a prototype that reliably acquires and transmits near real-time infrasonic data to facilitate the rapid location and identification of atmospheric events. (2) Provide documentation that could be used by the United States and foreign countries to procure infrasound systems commercially to fulfill their CTBT responsibilities. Infrasonic monitoring is an effective, low cost technology for detecting atmospheric explosions. The low frequency components of explosion signals propagate to long ranges (few thousand kilometers) where they can be detected with an array of sensors. Los Alamos National Laboratory's expertise in infrasound systems and phenomenology when combined with Sandia's expertise in providing verification quality system for treaty monitoring make an excellent team to provide the prototype infrasound sensor system. By September 1997, the prototype infrasound system will have been procured, integrated, evaluated and documented. Final documentation will include a system requirements document, an evaluation report and a hardware design document. The hardware design document will describe the various hardware components used in the infrasound prototype and their interrelationships

  10. Eight years' operation of the SGHWR prototype

    International Nuclear Information System (INIS)

    Phillips, J.L.

    1976-01-01

    Experience gained of the SGHWR system during the first eight years of operation of the UKAEA's 100 MW(e) prototype at AEE Winfrith is discussed. Modifications and additions have been made to the plant to overcome problems which only operation of a prototype unit can reveal. No problems have arisen which could not be overcome by the application of normal engineering resources, and there is no reason why the commercial successor to the prototype should be other than a fully viable proposition. (author)

  11. Field Data Logger Prototype for Power Converters

    DEFF Research Database (Denmark)

    Chaudhary, Sanjay; Ghimire, Pramod; Thøgersen, Paul Bach

    2014-01-01

    and subsequent analysis of the data. This paper presents the development of a low cost prototype field data logger prototype using Raspberry PI and industrial sensors. The functionalities of the data logger prototype are described. An online rainflow count algorithm has been implemented as well.......Mission profile data is very important for the cost effective and reliable design of power converters. The converter design can be improved on the basis of actual field data. Actual mission profile data can be collected for the power converters using field data loggers over a long period of time...

  12. NIF/LMJ prototype amplifier mechanical design

    International Nuclear Information System (INIS)

    Horvath, J.

    1996-10-01

    Amplifier prototypes for the National Ignition Facility and the Laser Megajoule will be tested at Lawrence Livermore National Laboratory. The prototype amplifier, which is an ensemble of modules from LLNL and Centre d'Etudes de Limeil-Valenton, is cassette-based with bottom access for maintenance. A sealed maintenance transfer vehicle which moves optical cassettes between the amplifier and the assembly cleanroom, and a vacuum gripper which holds laser slabs during cassette assembly will also be tested. The prototype amplifier will be used to verify amplifier optical performance, thermal recovery time, and cleanliness of mechanical operations

  13. Rapid prototyping using robot welding : process description

    OpenAIRE

    Ribeiro, António Fernando; Norrish, John

    1997-01-01

    Rapid Prototyping is a relatively recent technique to produce component prototypes for industry in a much shorter period of time, since the time to market a product is essential to its success. A new Rapid Prototyping process which uses metal as the raw material had been under development at Cranfield University in the last few years. The process uses a Gas Metal Arc fusion welding robot which deposits successive layers of metal in such way that it forms a 3D solid component. Firstly, a CAD s...

  14. Initial performance of the PIGMI prototype

    International Nuclear Information System (INIS)

    Stovall, J.E.

    1979-01-01

    The PIGMI (Pion Generator for Medical Irradiations) program at LASL is an accelerator development program aimed at completing the design of an accelerator suitable for use as a pion generator in a hospital-based radiotherapy program. The major thrust of the program has been the design of a 7 MeV prototype accelerator which emphasizes compactness, economy of construction, and operation and reliability. To achieve these goals the design of the prototype has exploited a number of innovations in proton linac technology. An overview of the program discussing the major innovative features of the prototype is presented. The initial operating experience is discussed and initial performance measurements are presented

  15. [Rapid prototyping: a very promising method].

    Science.gov (United States)

    Haverman, T M; Karagozoglu, K H; Prins, H-J; Schulten, E A J M; Forouzanfar, T

    2013-03-01

    Rapid prototyping is a method which makes it possible to produce a three-dimensional model based on two-dimensional imaging. Various rapid prototyping methods are available for modelling, such as stereolithography, selective laser sintering, direct laser metal sintering, two-photon polymerization, laminated object manufacturing, three-dimensional printing, three-dimensional plotting, polyjet inkjet technology,fused deposition modelling, vacuum casting and milling. The various methods currently being used in the biomedical sector differ in production, materials and properties of the three-dimensional model which is produced. Rapid prototyping is mainly usedforpreoperative planning, simulation, education, and research into and development of bioengineering possibilities.

  16. Mineral resources in Afghanistan. Final report

    International Nuclear Information System (INIS)

    1992-02-01

    Despite Afghanistan's wide variety of mineral resources and long history of small-scale mining of gems, gold, copper, and coal, it was not until the 1950's that the country's mineral resources were subject to systematic exploration. The report documents the past and present status of these resources and examines alternative strategies for their exploitation. Chapter 2 provides a brief history of minerals exploration, exploitation, and planning in Afghanistan, including the roles of Great Britain, France, Germany, the Soviet bloc, and the United States in Afghanistan's mineral sector; mineral policy in the five national plans during the years 1962-83; and sector assessments conducted by the World Bank (1978) and the US Department of Energy (1989). Chapter 3 discusses three strategies for developing the country's mineral and hydrocarbon resources. (1) a national orientation focusing on domestic needs; (2) a regional strategy that would consider markets in countries close to Afghanistan; and (3) an international strategy that would place Afghan resources on the international market

  17. Climatic control on clay mineral formation

    Indian Academy of Sciences (India)

    Many physico-chemical variables like rock-type,climate,topography and exposure age affect weathering environments.In the present study,an attempt is made to understand how the nature of clay minerals formed due to weathering differs in tropical regions receiving high and low rainfall. Clay mineralogy of weathering pro ...

  18. The mineral economy of Brazil--Economia mineral do Brasil

    Science.gov (United States)

    Gurmendi, Alfredo C.; Barboza, Frederico Lopes; Thorman, Charles H.

    1999-01-01

    This study depicts the Brazilian government structure, mineral legislation and investment policy, taxation, foreign investment policies, environmental laws and regulations, and conditions in which the mineral industry operates. The report underlines Brazil's large and diversified mineral endowment. A total of 37 mineral commodities, or groups of closely related commodities, is discussed. An overview of the geologic setting of the major mineral deposits is presented. This report is presented in English and Portuguese in pdf format.

  19. VO for Education: Archive Prototype

    Science.gov (United States)

    Ramella, M.; Iafrate, G.; De Marco, M.; Molinaro, M.; Knapic, C.; Smareglia, R.; Cepparo, F.

    2014-05-01

    The number of remote control telescopes dedicated to education is increasing in many countries, leading to correspondingly larger and larger amount of stored educational data that are usually available only to local observers. Here we present the project for a new infrastructure that will allow teachers using educational telescopes to archive their data and easily publish them within the Virtual Observatory (VO) avoiding the complexity of professional tools. Students and teachers anywhere will be able to access these data with obvious benefits for the realization of grander scale collaborative projects. Educational VO data will also be an important resource for teachers not having direct access to any educational telescopes. We will use the educational telescope at our observatory in Trieste as a prototype for the future VO educational data archive resource. The publishing infrastructure will include: user authentication, content and curation validation, data validation and ingestion, VO compliant resource generation. All of these parts will be performed by means of server side applications accessible through a web graphical user interface (web GUI). Apart from user registration, that will be validated by a natural person responsible for the archive (after having verified the reliability of the user and inspected one or more test files), all the subsequent steps will be automated. This means that at the very first data submission through the webGUI, a complete resource including archive and published VO service will be generated, ready to be registered to the VO. The efforts required to the registered user will consist only in describing herself/himself at registration step and submitting the data she/he selects for publishing after each observation sessions. The infrastructure will be file format independent and the underlying data model will use a minimal set of standard VO keywords, some of which will be specific for outreach and education, possibly including VO

  20. Characterization of Prototype LSST CCDs

    Energy Technology Data Exchange (ETDEWEB)

    OCONNOR,P.; FRANK, J.; GEARY, J.C.; GILMORE, D.K.; KOTOV, I.; RADEKA, V.; TAKACS, P.; TYSON, J.A.

    2008-06-23

    The ambitious science goals of the Large Synoptic Survey Telescope (LSST) will be achieved in part by a wide-field imager that will achieve a new level of performance in terms of area, speed, and sensitivity. The instrument performance is dominated by the focal plane sensors, which are now in development. These new-generation sensors will make use of advanced semiconductor technology and will be complemented by a highly integrated electronics package located inside the cryostat. A test laboratory has been set up at Brookhaven National Laboratory (BNL) to characterize prototype sensors and to develop test and assembly techniques for eventual integration of production sensors and electronics into modules that will form the final focal plane. As described in [1], the key requirements for LSST sensors are wideband quantum efficiency (QE) extending beyond lpm in the red, control of point spread function (PSF), and fast readout using multiple amplifiers per chip operated in parallel. In addition, LSST's fast optical system (f71.25) places severe constraints on focal plane flatness. At the chip level this involves packaging techniques to minimize warpage of the silicon die, and at the mosaic level careful assembly and metrology to achieve a high coplanarity of the sensor tiles. In view of the long lead time to develop the needed sensor technology, LSST undertook a study program with several vendors to fabricate and test devices which address the most critical performance features [2]. The remainder of this paper presents key results of this study program. Section 2 summarizes the sensor requirements and the results of design optimization studies, and Section 3 presents the sensor development plan. In Section 4 we describe the test bench at BNL. Section 5 reports measurement results obtained to date oh devices fabricated by several vendors. Section 6 presents a summary of the paper and an outlook for the future work. We present characterization methods and results on

  1. Controlling factors of uranium mineralization and prospect prediction in Qimantage area

    International Nuclear Information System (INIS)

    Yao Chunling; Zhu Pengfei; Cai Yuqi; Zhang Wenming; Zhao Yong'an; Song Jiye; Zhang Xiaojin

    2011-01-01

    Based on the analysis of regional geology in Qimantage area, the condition for uranium mineralization is summarized in regional geology setting, volcanic, granite and faults. This study shows that this area has favorable prospect for uranium mineralization. The metallogenic model is built up according to the controlling factors over uranium mineralization. Under this model, six potential areas are predicted in MRAS software with mineralization factors of synthetically geological information method. (authors)

  2. Issues affecting Northeast Asian minerals and energy markets

    International Nuclear Information System (INIS)

    Sheales, T.; Smith, V.

    1993-01-01

    Some of the broad issues likely to affect industry developments and trade in minerals and energy commodities in Northeast Asia in the 1990s are examined. Many of these issues will have a bearing on the development of mineral and energy resources of the Russian Far East region. 23 refs., 1 fig., 3 tabs

  3. The Miners' Radio Stations in Bolivia: A Culture of Resistance.

    Science.gov (United States)

    O'Connor, Alan

    1990-01-01

    Examines local community radio stations in rural regions of Bolivia. Finds that active miners' radio has flourished as an entertainment and political medium and that, through their radio stations, miners' organizations have played an important role in shaping the political position of the Bolivian union movement. (KEH)

  4. User prototypes as partly unconscious communication

    DEFF Research Database (Denmark)

    Glasemann, Marie; Kanstrup, Anne Marie

    2010-01-01

    In this paper, we introduce user prototypes as a technique that supports users’ articulation of emotions relevant for design: dreams, fears, motivations – their feelings and aspirations. Following Bateson’s writings about communication through art, we consider user prototypes as “partly unconscious...... communication” and propose to analyze them by focusing on the emotional articulations integrated in the users’ design language. We illustrate this with an example from a design research project on designing learning technology for young diabetics. The example shows how young people with diabetes can express...... emotional themes related to youth identity, the burden of being young with a chronic illness, and the need to be connected and feel safe through design of prototypes. The new conceptual space that arises from user prototypes shows potential for addressing emotions when designing for health and for further...

  5. Homogeneity of Prototypical Attributes in Soccer Teams

    Directory of Open Access Journals (Sweden)

    Christian Zepp

    2015-09-01

    Full Text Available Research indicates that the homogeneous perception of prototypical attributes influences several intragroup processes. The aim of the present study was to describe the homogeneous perception of the prototype and to identify specific prototypical subcategories, which are perceived as homogeneous within sport teams. The sample consists of N = 20 soccer teams with a total of N = 278 athletes (age M = 23.5 years, SD = 5.0 years. The results reveal that subcategories describing the cohesiveness of the team and motivational attributes are mentioned homogeneously within sport teams. In addition, gender, identification, team size, and the championship ranking significantly correlate with the homogeneous perception of prototypical attributes. The results are discussed on the basis of theoretical and practical implications.

  6. Norcal Prototype LNG Truck Fleet: Final Results

    Energy Technology Data Exchange (ETDEWEB)

    2004-07-01

    U.S. DOE and National Renewable Energy Laboratory evaluated Norcal Waste Systems liquefied natural gas (LNG) waste transfer trucks. Trucks had prototype Cummins Westport ISXG engines. Report gives final evaluation results.

  7. Gesture recognition for an exergame prototype

    NARCIS (Netherlands)

    Gacem, Brahim; Vergouw, Robert; Verbiest, Harm; Cicek, Emrullah; Kröse, Ben; van Oosterhout, Tim; Bakkes, S.C.J.

    2011-01-01

    We will demonstrate a prototype exergame aimed at the serious domain of elderly fitness. The exergame incorporates straightforward means to gesture recognition, and utilises a Kinect camera to obtain 2.5D sensory data of the human user.

  8. System design document for the INFLO prototype.

    Science.gov (United States)

    2014-03-01

    This report documents the high level System Design Document (SDD) for the prototype development and : demonstration of the Intelligent Network Flow Optimization (INFLO) application bundle, with a focus on the Speed : Harmonization (SPD-HARM) and Queu...

  9. Power test for first prototype LIBO module

    CERN Multimedia

    Laurent Guiraud

    2000-01-01

    The Linac Booster (LIBO) is a prototype machine for producing particle beams for cancer therapy. Hadron therapy techniques are able to reach deep tumours with less damage to surrounding tissue than with conventional radiotherapy.

  10. An Empirical Investigation of Architectural Prototyping

    DEFF Research Database (Denmark)

    Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2010-01-01

    Architectural prototyping is the process of using executable code to investigate stakeholders’ software architecture concerns with respect to a system under development. Previous work has established this as a useful and cost-effective way of exploration and learning of the design space of a system...... and in addressing issues regarding quality attributes, architectural risks, and the problem of knowledge transfer and conformance. However, the actual industrial use of architectural prototyping has not been thoroughly researched so far. In this article, we report from three studies of architectural prototyping...... in practice. First, we report findings from an ethnographic study of practicing software architects. Secondly, we report from a focus group on architectural prototyping involving architects from four companies. And, thirdly, we report from a survey study of 20 practicing software architects and software...

  11. Presentation Trainer Prototype 1.0

    NARCIS (Netherlands)

    Börner, Dirk; Specht, Marcus

    2014-01-01

    This software sketch comprises the first prototype of the presentation trainer. The application uses the Microsoft Kinect sensor and was built using the Processing 1.5.1 development environment. Available under the GNU LGPL licence version 3 or higher.

  12. Mineral commodity profiles: nitrogen

    Science.gov (United States)

    Kramer, Deborah A.

    2004-01-01

    Overview -- Nitrogen (N) is an essential element of life and a part of all animal and plant proteins. As a part of the DNA and RNA molecules, nitrogen is an essential constituent of each individual's genetic blueprint. As an essential element in the chlorophyll molecule, nitrogen is vital to a plant's ability to photosynthesize. Some crop plants, such as alfalfa, peas, peanuts, and soybeans, can convert atmospheric nitrogen into a usable form by a process referred to as 'fixation.' Most of the nitrogen that is available for crop production, however, comes from decomposing animal and plant waste or from commercially produced fertilizers. Commercial fertilizers contain nitrogen in the form of ammonium and/or nitrate or in a form that is quickly converted to the ammonium or nitrate form once the fertilizer is applied to the soil. Ammonia is generally the source of nitrogen in fertilizers. Anhydrous ammonia is commercially produced by reacting nitrogen with hydrogen under high temperatures and pressures. The source of nitrogen is the atmosphere, which is almost 80 percent nitrogen. Hydrogen is derived from a variety of raw materials, which include water, and crude oil, coal, and natural gas hydrocarbons. Nitrogen-based fertilizers are produced from ammonia feedstocks through a variety of chemical processes. Small quantities of nitrates are produced from mineral resources principally in Chile. In 2002, anhydrous ammonia and other nitrogen materials were produced in more than 70 countries. Global ammonia production was 108 million metric tons (Mt) of contained nitrogen. With 28 percent of this total, China was the largest producer of ammonia. Asia contributed 46 percent of total world ammonia production, and countries of the former U.S.S.R. represented 13 percent. North America also produced 13 percent of the total; Western Europe, 9 percent; the Middle East, 7 percent; Central America and South America, 5 percent; Eastern Europe, 3 percent; and Africa and Oceania

  13. OPAL jet chamber full scale prototype

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, H M; Hauschild, M; Hartmann, H; Hegerath, A; Boerner, H; Burckhart, H J; Dittmar, M; Hammarstroem, R; Heuer, R D; Mazzone, L

    1986-12-01

    The concept of a jet chamber for the central detector of OPAL has been tested with a full scale prototype. The design of this prototype, its mechanical and electrical structure and its support system for high voltage, gas, laser calibration and readout are described. Operating experience has been gathered since summer 1984. The chamber performance in terms of spatial resolution and particle identification capability is given.

  14. OPAL jet chamber full scale prototype

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, H M; Hauschild, M; Hartmann, H; Hegerath, A; Boerner, H; Burckhart, H J; Dittmar, M; Hammarstreom, R; Heuer, R D; Mazzone, L

    1986-05-22

    The concept of a jet chamber for the central detector of OPAL has been tested with a full scale prototype. The design of this prototype, its mechanical and electrical structure and its support system for high voltage, gas, laser calibration and readout are described. The operating experience gathered since the summer of 1984 and the chamber performance as measured by its spatial resolution and ability to identify particles are also given.

  15. Light Guide Collector Prototype: Laboratory Testing

    Directory of Open Access Journals (Sweden)

    Jitka - Mohelnikova

    2017-12-01

    Full Text Available The article reviews the potential of light guide system equipped by a concentrator device capturing daylight applicable for illumination of building interiors and presents results of experiments on performance of its prototype. The main goal is focused on the comparison of traditional solutions and newly developed prototype of the light guide system and presents examination of its light transmission efficiency based on the laboratory experiments.

  16. Light Guide Collector Prototype: Laboratory Testing

    OpenAIRE

    Jitka - Mohelnikova; Stanislav Darula; Ayodeji Omishore; Petr Mohelnik; Denis Micek

    2017-01-01

    The article reviews the potential of light guide system equipped by a concentrator device capturing daylight applicable for illumination of building interiors and presents results of experiments on performance of its prototype. The main goal is focused on the comparison of traditional solutions and newly developed prototype of the light guide system and presents examination of its light transmission efficiency based on the laboratory experiments.

  17. Software testing for evolutionary iterative rapid prototyping

    OpenAIRE

    Davis, Edward V., Jr.

    1990-01-01

    Approved for public release; distribution unlimited. Rapid prototyping is emerging as a promising software development paradigm. It provides a systematic and automatable means of developing a software system under circumstances where initial requirements are not well known or where requirements change frequently during development. To provide high software quality assurance requires sufficient software testing. The unique nature of evolutionary iterative prototyping is not well-suited for ...

  18. Automated prototyping tool-kit (APT)

    OpenAIRE

    Nada, Nader; Shing, M.; Berzins, V.; Luqi

    2002-01-01

    Automated prototyping tool-kit (APT) is an integrated set of software tools that generate source programs directly from real-time requirements. The APT system uses a fifth-generation prototyping language to model the communication structure, timing constraints, 1/0 control, and data buffering that comprise the requirements for an embedded software system. The language supports the specification of hard real-time systems with reusable components from domain specific component libraries. APT ha...

  19. Prototype_Matematikforløb_Sct-Hans

    DEFF Research Database (Denmark)

    Davidsen, Helle Munkholm; Sørensen, Kirsten Bonde; Klitø, Nanna Breinholt

    2015-01-01

    Forløbet udgør en prototype på et matematikforløb til 8. klasse, som er udviklet til at styrke og fastholde elevers motivation for læring. Formålet med denne prototype er at styrke motivationen for læring gennem synlige læringsmål, faglig differentiering og elevernes medbestemmelse. Didaktisk mål...

  20. Prototype_Danskforløb_Sct.Hans

    DEFF Research Database (Denmark)

    Davidsen, Helle Munkholm; Sørensen, Kirsten Bonde; Klitø, Nanna Breinholt

    2015-01-01

    Forløbet udgør en prototype på et danskforløb til 4. klasse, som er udviklet til at styrke og fastholde elevers motivation for læring. Formålet med denne prototype er at styrke motivationen for læring gennem synlige læringsmål, faglig differentiering og elevernes medbestemmelse. Didaktisk mål: at...

  1. Field evaluation of prototype electrofibrous filters

    International Nuclear Information System (INIS)

    Kuhl, W.D.; Bergman, W.; Biermann, A.H.; Lum, B.Y.

    1982-01-01

    New prototype electrofibrous filters were designed, built and evaluated in laboratory tests and in field installations. Two prototypes were designed for use in nuclear ventilation ducts as prefilters to HEPA filters. One prototype is designed to be a permanent component of the ventilation system while the other is a disposable unit. The disposable electrofibrous prefilter was installed in the exhaust stream of a glove box in which barrels of uranium turnings are burned. Preliminary tests show the disposal prefilter is effectively prolonging the HEPA filter life. An earlier prototype of the rolling prefilter was upgraded to meet the increased requirements for installation in a nuclear facility. This upgraded prototype was evaluated in the fire test facility at LLNL and shown to be effective in protecting HEPA filters from plugging under the most severe smoke conditions. The last prototype described in this report is a recirculating air filter. After demonstrating a high performance in laboratory tests the unit was shipped to Savannah River where it is awaiting installation in a Pu fuel fabrication facility. An analysis of the particulate problem in Savannah River indicates that four recirculating air filter will save $172,000 per year in maintenance costs

  2. MPACT Fast Neutron Multiplicity System Prototype Development

    Energy Technology Data Exchange (ETDEWEB)

    D.L. Chichester; S.A. Pozzi; J.L. Dolan; M.T. Kinlaw; S.J. Thompson; A.C. Kaplan; M. Flaska; A. Enqvist; J.T. Johnson; S.M. Watson

    2013-09-01

    This document serves as both an FY2103 End-of-Year and End-of-Project report on efforts that resulted in the design of a prototype fast neutron multiplicity counter leveraged upon the findings of previous project efforts. The prototype design includes 32 liquid scintillator detectors with cubic volumes 7.62 cm in dimension configured into 4 stacked rings of 8 detectors. Detector signal collection for the system is handled with a pair of Struck Innovative Systeme 16-channel digitizers controlled by in-house developed software with built-in multiplicity analysis algorithms. Initial testing and familiarization of the currently obtained prototype components is underway, however full prototype construction is required for further optimization. Monte Carlo models of the prototype system were performed to estimate die-away and efficiency values. Analysis of these models resulted in the development of a software package capable of determining the effects of nearest-neighbor rejection methods for elimination of detector cross talk. A parameter study was performed using previously developed analytical methods for the estimation of assay mass variance for use as a figure-of-merit for system performance. A software package was developed to automate these calculations and ensure accuracy. The results of the parameter study show that the prototype fast neutron multiplicity counter design is very nearly optimized under the restraints of the parameter space.

  3. Investigating the role of implicit prototypes in the prototype willingness model.

    Science.gov (United States)

    Howell, Jennifer L; Ratliff, Kate A

    2017-06-01

    One useful theory to predict health behavior is the prototype-willingness model (PWM), which posits that people are more willing to engage in behavior to the extent that they have a positive view of the prototypical person who performs that behavior. The goal of the present research is to test whether adding an implicit measure of prototype favorability might improve explanatory power in the PWM. Two studies examined whether implicit prototype favorability uniquely predicted White women's intentions to engage in healthy sun behavior over the next 3-6 months, and their willingness to engage in risky sun behavior, should the opportunity arise. The results suggested that implicit prototype favorability, particularly implicit prototypes of those who engage in risky UV-related behaviors, uniquely predicted intentions to engage in healthy sun behavior and willingness to engage in risky sun behavior in the PWM.

  4. Numerical study of similarity in prototype and model pumped turbines

    International Nuclear Information System (INIS)

    Li, Z J; Wang, Z W; Bi, H L

    2014-01-01

    Similarity study of prototype and model pumped turbines are performed by numerical simulation and the partial discharge case is analysed in detail. It is found out that in the RSI (rotor-stator interaction) region where the flow is convectively accelerated with minor flow separation, a high level of similarity in flow patterns and pressure fluctuation appear with relative pressure fluctuation amplitude of model turbine slightly higher than that of prototype turbine. As for the condition in the runner where the flow is convectively accelerated with severe separation, similarity fades substantially due to different topology of flow separation and vortex formation brought by distinctive Reynolds numbers of the two turbines. In the draft tube where the flow is diffusively decelerated, similarity becomes debilitated owing to different vortex rope formation impacted by Reynolds number. It is noted that the pressure fluctuation amplitude and characteristic frequency of model turbine are larger than those of prototype turbine. The differences in pressure fluctuation characteristics are discussed theoretically through dimensionless Navier-Stokes equation. The above conclusions are all made based on simulation without regard to the penstock response and resonance

  5. Development of a prototype GIS for risk-hazard assessment

    International Nuclear Information System (INIS)

    Devonport, C.

    1992-01-01

    A collaborative research agreement between the Supervising Scientist for the Alligator Rivers Region (OSS) and the Northern Territory University (NTU) aims to develop and assess a computer-based Geographic Information System (GIS) to integrate terrain and geological data for risk-hazard analysis and modelling. This paper outlines initial design and development of the prototype GIS including the input of trial data of various types. It is recognised that the GIS must be flexible enough to accommodate change and provide a base for a variety of research needs. Such functionality is likely to be provided best by an initially small, generic prototype GIS to which functions and data are added as required. Properties of the prototype identified as critical to its usefulness include integration of different types of data into the system, understanding and accommodating inconsistencies between data sets and the recognition and recording of error. Various types of data (elevation data, maps and images) available at the outset of the project are outlined together with a brief discussion on their source, integration into the database, derivative products and the potential usefulness of, and problems associated with, the different data formats. The analytical possibilities offered by the trial data will be explored next and the results of the first development cycle presented by the end of 1992. Subsequently, additional data will be incorporated into the database, analytical techniques will be used to build models, and user-driven development will enable the GIS to begin to support a decision research process. 20 refs

  6. Espresso beverages of pure origin coffee: mineral characterization, contribution for mineral intake and geographical discrimination.

    Science.gov (United States)

    Oliveira, Marta; Ramos, Sandra; Delerue-Matos, Cristina; Morais, Simone

    2015-06-15

    Espresso coffee beverages prepared from pure origin roasted ground coffees from the major world growing regions (Brazil, Ethiopia, Colombia, India, Mexico, Honduras, Guatemala, Papua New Guinea, Kenya, Cuba, Timor, Mussulo and China) were characterized and compared in terms of their mineral content. Regular consumption of one cup of espresso contributes to a daily mineral intake varying from 0.002% (sodium; Central America) to 8.73% (potassium; Asia). The mineral profiles of the espresso beverages revealed significant inter- and intra-continental differences. South American pure origin coffees are on average richer in the analyzed elements except for calcium, while samples from Central America have generally lower mineral amounts (except for manganese). Manganese displayed significant differences (pworld coffee producers were achieved by applying canonical discriminant analysis. Manganese and calcium were found to be the best chemical descriptors for origin. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Novice designers’ use of prototypes in engineering design

    Science.gov (United States)

    Deininger, Michael; Daly, Shanna R.; Sienko, Kathleen H.; Lee, Jennifer C.

    2017-01-01

    Prototypes are essential tools in product design processes, but are often underutilized by novice designers. To help novice designers use prototypes more effectively, we must first determine how they currently use prototypes. In this paper, we describe how novice designers conceptualized prototypes and reported using them throughout a design project, and compare reported prototyping use to prototyping best practices. We found that some of the reported prototyping practices by novice designers, such as using inexpensive prototypes early and using prototypes to define user requirements, occurred infrequently and lacked intentionality. Participants’ initial descriptions of prototypes were less sophisticated than how they later described using them and only upon prompted reflection did participants recognize more specific benefits of using prototypes. PMID:29398740

  8. Minerals in deserts

    International Nuclear Information System (INIS)

    Smith, G.I.

    1982-01-01

    Almost any kind of mineral deposit can occur in desert areas, and the lack of vegetation and soil cover makes finding them easier. Some kinds of deposits, though, are more likely to occur in deserts than elsewhere. Some of these result from processes genetically related to the present desert climate that improved lower grade deposits of ore. One such process, termed secondary enrichment, is most effective in areas with deep water tables, and many low-grade copper, silver, and uranium deposits have been converted into mineable ore by the downward migration and redeposition of soluble metals. In a desert terrane, placer processes are effective whenever running water flowing over steep slopes erodes outcropping ore bodies and transports and concentrates the heavier ore minerals at lower levels, thus converting low-grade or hard-to-mine bedrock deposits into economically workable concentrations. Other kinds of deposits are better preserved in deserts because the lower rainfall at the surface, and the lower volume of flow and the greater depths to groundwater, result in less destruction of soluble ores; deposits of salines and phosphates are the most notable ores affected by these factors. Still other ore deposits are created as a consequence of the arid climate, mostly because the high evaporation rates operating on standing bodies of water produce brines that can lead directly to concentrations of salts and indirectly to secondary minerals, such as zeolites, that are produced by reaction of silicate minerals with saline waters

  9. Carbonizing bituminous minerals

    Energy Technology Data Exchange (ETDEWEB)

    1921-05-01

    A process for carbonizing bituminous minerals, like oil-shale, in a furnace with addition of air in the presence of heat-receiving material is characterized by the fact that to the feed such solid or liquid material (with the exception of oil) is added, which, through vaporization or heat-binding decomposition or conversion, hinders the establishment of excessive temperatures.

  10. Uruguay minerals fuels

    International Nuclear Information System (INIS)

    Goso, H.

    1967-01-01

    In this report the bases for the development of the necessary works of prospection are exposed on mineral fuels of Uruguay. We have taken the set from: coal, lutitas bituminous, uranium, petroleum and disturbs. In all the cases we have talked about to the present state of the knowledge and to the works that we considered necessary to develop in each case

  11. Prototype Learning and Dissociable Categorization Systems in Alzheimer’s Disease

    Science.gov (United States)

    Heindel, William C.; Festa, Elena K.; Ott, Brian R.; Landy, Kelly M.; Salmon, David P.

    2015-01-01

    Recent neuroimaging studies suggest that prototype learning may be mediated by at least two dissociable memory systems depending on the mode of acquisition, with A/Not-A prototype learning dependent upon a perceptual representation system located within posterior visual cortex and A/B prototype learning dependent upon a declarative memory system associated with medial temporal and frontal regions. The degree to which patients with Alzheimer’s disease (AD) can acquire new categorical information may therefore critically depend upon the mode of acquisition. The present study examined A/Not-A and A/B prototype learning in AD patients using procedures that allowed direct comparison of learning across tasks. Despite impaired explicit recall of category features in all tasks, patients showed differential patterns of category acquisition across tasks. First, AD patients demonstrated impaired prototype induction along with intact exemplar classification under incidental A/Not-A conditions, suggesting that the loss of functional connectivity within visual cortical areas disrupted the integration processes supporting prototype induction within the perceptual representation system. Second, AD patients demonstrated intact prototype induction but impaired exemplar classification during A/B learning under observational conditions, suggesting that this form of prototype learning is dependent on a declarative memory system that is disrupted in AD. Third, the surprisingly intact classification of both prototypes and exemplars during A/B learning under trial-and-error feedback conditions suggests that AD patients shifted control from their deficient declarative memory system to a feedback-dependent procedural memory system when training conditions allowed. Taken together, these findings serve to not only increase our understanding of category learning in AD, but to also provide new insights into the ways in which different memory systems interact to support the acquisition of

  12. Aggregate and Mineral Resources - Industrial Mineral Mining Operations

    Data.gov (United States)

    NSGIC Education | GIS Inventory — An Industrial Mineral Mining Operation is a DEP primary facility type related to the Industrial Mineral Mining Program. The sub-facility types are listed below:Deep...

  13. Prototyping for surgical and prosthetic treatment.

    Science.gov (United States)

    Goiato, Marcelo Coelho; Santos, Murillo Rezende; Pesqueira, Aldiéris Alves; Moreno, Amália; dos Santos, Daniela Micheline; Haddad, Marcela Filié

    2011-05-01

    Techniques of rapid prototyping were introduced in the 1980s in the field of engineering for the fabrication of a solid model based on a computed file. After its introduction in the biomedical field, several applications were raised for the fabrication of models to ease surgical planning and simulation in implantology, neurosurgery, and orthopedics, as well as for the fabrication of maxillofacial prostheses. Hence, the literature has described the evolution of rapid prototyping technique in health care, which allowed easier technique, improved surgical results, and fabrication of maxillofacial prostheses. Accordingly, a literature review on MEDLINE (PubMed) database was conducted using the keywords rapid prototyping, surgical planning, and maxillofacial prostheses and based on articles published from 1981 to 2010. After reading the titles and abstracts of the articles, 50 studies were selected owing to their correlations with the aim of the current study. Several studies show that the prototypes have been used in different dental-medical areas such as maxillofacial and craniofacial surgery; implantology; neurosurgery; orthopedics; scaffolds of ceramic, polymeric, and metallic materials; and fabrication of personalized maxillofacial prostheses. Therefore, prototyping has been an indispensable tool in several studies and helpful for surgical planning and fabrication of prostheses and implants.

  14. Refrigerating liquid prototype for LED's thermal management

    International Nuclear Information System (INIS)

    Faranda, Roberto; Guzzetti, Stefania; Lazaroiu, George Cristian; Leva, Sonia

    2012-01-01

    The heat management is the critical factor for high performance operation of LED. A new heat management application of refrigerating liquid integrated within a fabricated prototype is proposed and investigated. A series of experiments considering different heights of liquid level were performed to evaluate the heat dissipation performance and optical characteristics of the refrigerating liquid based prototype. The results reveal that the junction temperature decreases as the level of refrigerating liquid increases. The experimental results report that the refrigerating liquid reduces the junction temperature, and can positively influence the luminous radiation performances. An optimization investigation of the proposed solution was carried out to find an optimum thermal performance. The experiments indicated that refrigerating liquid cooling is a powerful way for heat dissipation of high power LEDs, and the fabrication of prototype was feasible and useful. - Highlights: ► New heat management application of refrigerating liquid on a fabricated LED prototype. ► Thermal models setup and comparison between the classical and the new solutions. ► The impact of refrigerating liquid level on LED thermal and luminous performances. ► The relationship between different levels of liquid with LED prototype performances.

  15. Prototype superconducting magnet for the FFAG accelerator

    International Nuclear Information System (INIS)

    Obana, T.; Ogitsu, T.; Yamamoto, A.; Yoshimoto, M.; Mori, Y.; Fujii, T.; Iwasa, M.; Orikasa, T.

    2006-01-01

    A study of a superconducting magnet for the Fixed Field Alternating Gradient (FFAG) accelerator has been performed. The FFAG accelerator requires static magnetic field, and it is suitable for superconducting magnet applications, because problems associated with time varying magnetic field such as eddy current loss can be eliminated. The superconducting magnet, which can generate high magnetic field, is possible to realize a higher beam energy with a given accelerator size or the size to be smaller for a given beam energy. The FFAG accelerator magnet is demanded to have a complicated nonlinear magnetic field with high accuracy. As a first prototype superconducting coil, the coil configuration which consists of left-right asymmetric cross-section and large aperture has been designed. The prototype coil has been successfully developed by using a 6-axis Computer Numerical Control (CNC) winding machine. The magnetic field of the prototype coil has been demonstrated in warm measurement. As a consequence, the technical feasibility has been verified with the prototype coil development and the performance test. In addition, the technology components developed in the prototype coil have a possibility to transfer to a fusion magnet

  16. Close encounters of the prototype kind

    CERN Multimedia

    2005-01-01

    CERN is building a new control centre for the operation of its entire accelerator complex and technical infrastructure. The prototype console for the new centre has just been installed and tested. Close encounters of the prototype kind CERN is building a new control centre for the operation of its entire accelerator complex and technical infrastructure. The prototype console for the new centre has just been installed and tested. The prototype of the control consoles that will be at the heart of the future CERN Control Centre (CCC) has just been installed in the Roy Billinge Room in Building 354. Until now, there have been four separate control rooms for the CERN accelerators and technical infrastructure. The CCC, which will be located on the Prévessin site, will bring them all together in a single room. The Centre will consist of 40 consoles for four different areas (LHC, SPS, PS complex and technical infrastructure). The prototype was tested by the technicians for a month. Following installation and con...

  17. Prototype tests for the ALICE TRD

    International Nuclear Information System (INIS)

    Andronic, A.; Appelshaeuser, H.; Herrmann, N.; Mahmoud, T.; Schicker, R.; Stachel, J.; Wessels, J.; Windelband, B.; Xu, C.; Blume, C.; Braun-Munzinger, P.; Daues, H.; Devismes, A.; Finck, Ch.; Sedykh, S.; Simon, R. S.; Stelzer, H.; Bucher, D.; Lister, T.; Peitzmann, T.; Reygers, K.; Santo, R.; Winkelmann, O.; Catanescu, V.; Ciobanu, M.; Petrovici, M.; Blume, C.; Braun-Munzinger, P.; Daues, H.; Devismes, A.; Finck, Ch.; Sedykh, S.; Simon, R. S.; Stelzer, H.

    2001-01-01

    The ALICE Transition Radiation Detector (TRD) has been designed to improve the pion rejection capability of the ALICE detector by at least a factor of 100 for momenta above 2 GeV/c. To demonstrate that this goal is achievable, during the last year we have conducted prototype tests at the pion (with natural electron content) beam facility at GSI Darmstadt. A complete description of the experimental setup and of the results (including references) can be found in two previous papers by Andronic et al. Many types of radiators were tested, composed of foils, fibres and foams. Here we summarize the results concerning the pion rejection performance in case of a fibre (of 17 μm diameter) radiator, which was established to be the best candidate for the final radiator. To extract the pion rejection factor we have studied three different methods: i) truncated mean of integrated energy deposit, TMQ; ii) likelihood on integrated energy deposit, L-Q; iii) bidimensional likelihood on energy deposit and position of the largest cluster found in the drift region of the DC, L-QX. We present the pion efficiency (the inverse of the rejection factor) as function of electron efficiency (90% electron efficiency is the commonly used value) in case of fibre radiators for the momentum of 1 GeV/c. The truncated mean method, although it delivers sizeably worse identification, has the advantage of being very easy to use, being advantageous especially for an on-line identification. The bidimensional likelihood delivers the best rejection factor. In general, the three methods employed here give results in good agreement with earlier studies. By doubling the equivalent thickness of the radiator one gains a factor of about 2 in pion rejection power. However, it remains to be seen how the additional material will influence (by producing secondary particles) the performance of the TRD itself and of other ALICE sub-detectors. The pion efficiency at 90% electron efficiency as function of momentum is

  18. Minería de datos aplicada a la educación: modelo de deserción universitaria en la Universidad Tecnológica Nacional, Facultad Regional Rosario

    OpenAIRE

    Valía, Luciano; Rostagno, José; Moine, Juan Miguel; Bigatti, Cristian; Riva, Fabiana María; Amar, Eduardo

    2017-01-01

    La deserción universitaria es uno de los mayores problemas que atraviesan las Universidades de nuestro país. La Minería de Datos es una disciplina que puede colaborar con esta situación, brindando un conjunto de técnicas y métodos para detectar patrones de comportamiento en los alumnos y accionar en consecuencia. Por este motivo, abordamos un estudio cuyo objetivo es el descubrimiento de patrones de deserción universitaria en la carrera Ingeniería en Sistemas de Información de la Universidad ...

  19. Calibration of a prototype NIRS oximeter against two commercial devices on a blood-lipid phantom

    DEFF Research Database (Denmark)

    Hyttel-Sorensen, Simon; Kleiser, Stefan; Wolf, Martin

    2013-01-01

    In a blood-lipid liquid phantom the prototype near-infrared spectroscopy oximeter OxyPrem was calibrated against the INVOS® 5100c adult sensor in respect to values of regional tissue oxygen haemoglobin saturation (rStO2) for possible inclusion in the randomised clinical trial - SafeBoosC. In addi......In a blood-lipid liquid phantom the prototype near-infrared spectroscopy oximeter OxyPrem was calibrated against the INVOS® 5100c adult sensor in respect to values of regional tissue oxygen haemoglobin saturation (rStO2) for possible inclusion in the randomised clinical trial - Safe...

  20. Application of rapid prototyping technology in the prototype manufacturing for evaluation of NPP components and equipments

    International Nuclear Information System (INIS)

    Park, C. Y.; Kim, J. W.; Shon, H. K.; Choi, H. S.; Yang, D. Y.

    2001-01-01

    A brief overview of rapid prototyping technology in which a part with complex shape can be produced easily and rapidly in a layer-by-layer additive manner is given in this article. In addition, a prototype model of a complex fan is manufactured using three-dimensional solid CAD modeling and Laminated Object Manufacturing (LOM), a rapid prototyping technology. This enables designers to verify and modify design rapidly at an early stage of product development; and the prototype model of a fan can be used as a pattern for various secondary casting process such as vacumm casting, lost-paper casting to make prototypes of a fan. It has been shown that the combination of three-dimensional solid CAD modeling and rapid prototyping technology can reduce greatly the cost and time of prototyping of fans and turbine blades in comparison with conventional CNC machining. It should also be noted that rapid prototyping technology enables the visualization of various physical and chemical defects at a nuclear power plant so that it can help engineers understand those defects in an effective way

  1. The Prototype as Mediator of Embodied Experience in Fashion Design

    DEFF Research Database (Denmark)

    Kristensen, Tore; Ræbild, Ulla

    . It is based on photographic material obtained in design studios during prototype development. The prototype is considered a core fashion design competence. Yet, companies increasingly cut costs by reducing or omitting prototype development. We intend to show, how the garment prototype acts as an important...

  2. Oxygen Extraction from Minerals

    Science.gov (United States)

    Muscatello, Tony

    2017-01-01

    Oxygen, whether used as part of rocket bipropellant or for astronaut life support, is a key consumable for space exploration and commercialization. In Situ Resource Utilization (ISRU) has been proposed many times as a method for making space exploration more cost effective and sustainable. On planetary and asteroid surfaces the presence of minerals in the regolith that contain oxygen is very common, making them a potential oxygen resource. The majority of research and development for oxygen extraction from minerals has been for lunar regolith although this work would generally be applicable to regolith at other locations in space. This presentation will briefly survey the major methods investigated for oxygen extraction from regolith with a focus on the current status of those methods and possible future development pathways. The major oxygen production methods are (1) extraction from lunar ilmenite (FeTiO3) with either hydrogen or carbon monoxide, (2) carbothermal reduction of iron oxides and silicates with methane, and (3) molten regolith electrolysis (MRE) of silicates. Methods (1) and (2) have also been investigated in a two-step process using CO reduction and carbon deposition followed by carbothermal reduction. All three processes have byproducts that could also be used as resources. Hydrogen or carbon monoxide reduction produce iron metal in small amounts that could potentially be used as construction material. Carbothermal reduction also makes iron metal along with silicon metal and a glass with possible applications. MRE produces iron, silicon, aluminum, titanium, and glass, with higher silicon yields than carbothermal reduction. On Mars and possibly on some moons and asteroids, water is present in the form of mineral hydrates, hydroxyl (-OH) groups on minerals, andor water adsorbed on mineral surfaces. Heating of the minerals can liberate the water which can be electrolyzed to provide a source of oxygen as well. The chemistry of these processes, some key

  3. Indústria mineral

    Directory of Open Access Journals (Sweden)

    Iran F. Machado

    1998-08-01

    Full Text Available A INDÚSTRIA mineral brasileira é analisada, de modo sucinto, face aos desafios impostos pela globalização contemporânea. As mudanças profundas ocorridas no contexto internacional na última década, abrangendo as esferas política, econômica, social e institucional, exigem uma reflexão aprofundada sobre o papel a ser desempenhado pelo Brasil no comércio internacional de bens minerais. De um lado, as oportunidades de aproveitamento de jazidas de classe internacional, principalmente na Amazônia, são bastante promissoras. Por outro, não se deve ignorar que: a explotação dessas reservas terá de obedecer a critérios de sustentabilidade, seguindo paradigmas já adotados em países desenvolvidos; o Brasil terá de garantir a sua competitividade diante dos seus principais concorrentes (Austrália, CEI, China e Índia. A questão dos minerais estratégicos é também abordada, com ênfase nas preocupações demonstradas pelo Departamento de Estado dos EUA. Finalmente, são alinhados três cenários possíveis para o desempenho futuro da mineração brasileira, instando-se o governo a dedicar maior atenção ao destino do nosso subsolo.THE MINERAL industry of Brazil is briefly analysed vis-à-vis the challenges imposed by the cruenta globalization process. The profound changes that occurred in the international framework during the last decade, encompassing the political, economic, social, and institutional structures, demand a thorough appraisal about the role to be played by Brazil in the international market of mineral commodities. On one hand, the opportunities open for world class deposits, mainly in the Amazon, are very promising. On the other hand, it is mandatory to take into account that: the exploitation of these reserves shall comply with sound sustainability criteria, following guidelines already adopted by some developed countries; Brazil will have to demonstrate its competitiveness among the major competitors (Australia

  4. A COMPUTERIZED OPERATOR SUPPORT SYSTEM PROTOTYPE

    Energy Technology Data Exchange (ETDEWEB)

    Thomas A. Ulrich; Roger Lew; Ronald L. Boring; Ken Thomas

    2015-03-01

    A computerized operator support system (COSS) is proposed for use in nuclear power plants to assist control room operators in addressing time-critical plant upsets. A COSS is a collection of technologies to assist operators in monitoring overall plant performance and making timely, informed decisions on appropriate control actions for the projected plant condition. A prototype COSS was developed in order to demonstrate the concept and provide a test bed for further research. The prototype is based on four underlying elements consisting of a digital alarm system, computer-based procedures, piping and instrumentation diagram system representations, and a recommender module for mitigation actions. The initial version of the prototype is now operational at the Idaho National Laboratory using the Human System Simulation Laboratory.

  5. Generalizing Prototype Theory: A Formal Quantum Framework

    Science.gov (United States)

    Aerts, Diederik; Broekaert, Jan; Gabora, Liane; Sozzo, Sandro

    2016-01-01

    Theories of natural language and concepts have been unable to model the flexibility, creativity, context-dependence, and emergence, exhibited by words, concepts and their combinations. The mathematical formalism of quantum theory has instead been successful in capturing these phenomena such as graded membership, situational meaning, composition of categories, and also more complex decision making situations, which cannot be modeled in traditional probabilistic approaches. We show how a formal quantum approach to concepts and their combinations can provide a powerful extension of prototype theory. We explain how prototypes can interfere in conceptual combinations as a consequence of their contextual interactions, and provide an illustration of this using an intuitive wave-like diagram. This quantum-conceptual approach gives new life to original prototype theory, without however making it a privileged concept theory, as we explain at the end of our paper. PMID:27065436

  6. Prototype Hanford Surface Barrier: Design basis document

    International Nuclear Information System (INIS)

    Myers, D.R.; Duranceau, D.A.

    1994-11-01

    The Hanford Site Surface Barrier Development Program (BDP) was organized in 1985 to develop the technology needed to provide a long-term surface barrier capability for the Hanford Site and other arid sites. This document provides the basis of the prototype barrier. Engineers and scientists have momentarily frozen evolving barrier designs and incorporated the latest findings from BDP tasks. The design and construction of the prototype barrier has required that all of the various components of the barrier be brought together into an integrated system. This integration is particularly important because some of the components of the protective barreir have been developed independently of other barreir components. This document serves as the baseline by which future modifications or other barrier designs can be compared. Also, this document contains the minutes of meeting convened during the definitive design process in which critical decisions affecting the prototype barrier's design were made and the construction drawings

  7. Mobile Prototyping Platforms for Remote Engineering Applications

    Directory of Open Access Journals (Sweden)

    Karsten Henke

    2009-08-01

    Full Text Available This paper describes a low-cost mobile communication platform as a universal rapid-prototyping system, which is based on the Quadrocopter concept. At the Integrated Hardware and Software Systems Group at the Ilmenau University of Technology these mobile platforms are used to motivate bachelor and master students to study Computer Engineering sciences. This could be done by increasing their interest in technical issues, using this platform as integral part of a new ad-hoc lab to demonstrate different aspects in the area of Mobile Communication as well as universal rapid prototyping nodes to investigate different mechanisms for self-organized mobile communication systems within the International Graduate School on Mobile Communications. Beside the three fields of application, the paper describes the current architecture concept of the mobile prototyping platform as well as the chosen control mechanism and the assigned sensor systems to fulfill all the required tasks.

  8. Iterative Prototyping of Strategy Implementation Workshop Design

    DEFF Research Database (Denmark)

    Kryger, Anders

    2018-01-01

    Purpose: The purpose of this paper is to demonstrate how a strategy implementation workshop design can be developed and tested while minimizing the time spent on developing the design. Design/methodology/approach: This multiple case study at a diesel engine company shows how iterative prototyping...... can be used to structure the design process of a strategy implementation workshop. Findings: Strategy implementation workshop design can be developed in resource-constrained environments through iterative prototyping of the workshop design. Each workshop iteration can generate value in its own right...... draw on his/her experience as well as add to his/her knowledge base. Originality/value: Introducing iterative prototyping in an organizational context can facilitate fast yet structured development of a rigorous workshop design. Strategy consultants are provided with empirical examples of how...

  9. Generalizing Prototype Theory: A Formal Quantum Framework

    Directory of Open Access Journals (Sweden)

    Diederik eAerts

    2016-03-01

    Full Text Available Theories of natural language and concepts have been unable to model the flexibility, creativity, context-dependence, and emergence, exhibited by words, concepts and their combinations. The mathematical formalism of quantum theory has instead been successful in capturing these phenomena such as graded membership, situational meaning, composition of categories, and also more complex decision making situations, which cannot be modeled in traditional probabilistic approaches. We show how a formal quantum approach to concepts and their combinations can provide a powerful extension of prototype theory. We explain how prototypes can interfere in conceptual combinations as a consequence of their contextual interactions, and provide an illustration of this using an intuitive wave-like diagram. This quantum-conceptual approach gives new life to original prototype theory, without however making it a privileged concept theory, as we explain at the end of our paper.

  10. Licensing management system prototype system design

    International Nuclear Information System (INIS)

    Immerman, W.H.; Arcuni, A.A.; Elliott, J.M.; Chapman, L.D.

    1983-11-01

    This report is a design document for a prototype implementation of a licensing management system (LMS) as defined in SAND83-7080. It describes the concept of operations for full implementation of an LMS in accordance with the previously defined functional requirements. It defines a subset of a full LMS suitable for meeting prototype implementation goals, and proposes a system design for this subset. The report describes overall system design considerations consistent with, but more explicit than the general characteristics required by the LMS functional definition. A high level design is presented for just those functions selected for prototype implementation. The report also provides a data element dictionary describing the structured logical data elements required to implement the selected functions

  11. Molecular Characterization of Bacterial Respiration on Minerals

    Energy Technology Data Exchange (ETDEWEB)

    Blake, Robert C.

    2013-04-26

    anomalous dispersion (MAD) phasing; 4. An acid-stable red cytochrome with a novel absorbance peak at 579 nm was purified from cell-free extracts of L. ferriphilum. Functional studies demonstrated that this cytochrome was an important component of the aerobic iron respiratory chain in this organism; 5. The specific adhesion of At. ferrooxidans to pyrite is mediated by an extracellular protein that was identified as aporusticyanin. The adhesion of At. ferrooxidans to minerals was characterized by high affinity binding that exhibited a high specificity for pyrite over other sulfide minerals. The principal biopolymer involved in this high-affinity adhesion to pyrite was isolated by mineral affinity chromatography and identified as aporusticyanin. The adhesion of purified aporusticyanin to minerals was observed to adhere to different mineral with a pattern of reactivity identical to that observed with the intact bacterium. Further, preincubation of pyrite with excess exogenous aporusticyanin served to inhibit the adherence of intact cells to the surface of the mineral, indicating that the protein and the cells adhered to the pyrite in a mutually exclusive manner. Taken together, these observations support a model where aporusticyanin located on the surface of the bacterial cell acts as a mineral-specific receptor for the initial adherence of At. ferrooxidans to solid pyrite; 6. The specific adhesion of L. ferriphilum to pyrite was mediated by a different acid-stable extracellular protein than aporusticyanin; and 7. A prototype integrating cavity absorption meter (ICAM) was assembled to determine whether this novel spectrophotometer could be used to study cellular respiration in situ.

  12. From research plots to prototype biomass plantations

    Energy Technology Data Exchange (ETDEWEB)

    Kenney, W.A.; Vanstone, B.J.; Gambles, R.L.; Zsuffa, L. [Univ. of Toronto, Ontario (Canada)

    1993-12-31

    The development of biomass energy plantations is now expanding from the research plot phase into the next level of development at larger scale plantings. This is necessary to provide: more accurate information on biomass yields, realistic production cost figures, venues to test harvesting equipment, demonstration sites for potential producers, and a supply of feedstock for prototype conversion facilities. The paper will discuss some of these objectives and some of the challenges encountered in the scale-up process associated with a willow prototype plantation project currently under development in Eastern Canada.

  13. Modelling and Control of the Wavestar Prototype

    DEFF Research Database (Denmark)

    Hansen, Rico Hjerm; Kramer, Morten M.

    2011-01-01

    Algorithm (WPEA), applied to the full-scale Wavestar Prototype for maximizing energy extraction. The WPEA is optimized based on simulations of the point absorbers in different sea states. Hence, a presentation of a hydrodynamic model of the Wavestar is included in the paper. A simplified Power Take-Off (PTO......) is also added to the model, enabling the optimization of the WPEA to take into account the PTO constraints of PTO bandwidth and force limitations. The predicted results of the optimized WPEA are compared to real measurements from theWavestar Prototype, showing good compliance....

  14. Rapid Prototyping: Technologies, Materials and Advances

    Directory of Open Access Journals (Sweden)

    Dudek P.

    2016-06-01

    Full Text Available In the context of product development, the term rapid prototyping (RP is widely used to describe technologies which create physical prototypes directly from digital data. Recently, this technology has become one of the fastest-growing methods of manufacturing parts. The paper provides brief notes on the creation of composites using RP methods, such as stereolithography, selective laser sintering or melting, laminated object modelling, fused deposition modelling or three-dimensional printing. The emphasis of this work is on the methodology of composite fabrication and the variety of materials used in these technologies.

  15. RK-TBA prototype RF source

    International Nuclear Information System (INIS)

    Houck, T.; Anderson, D.; Giordano, G.

    1996-01-01

    A prototype rf power source based on the Relativistic Klystron Two-Beam Accelerator (RK-TBA) concept is being constructed at the Lawrence Berkeley National Laboratory to study physics, engineering, and costing issues. The prototype is described and compared to a full scale design appropriate for driving the Next Linear Collider (NLC). Specific details of the induction core tests and pulsed power system are presented. The 1-MeV, 1.2-kA induction gun currently under construction is also described in detail

  16. The prototype of radioactive ion source

    CERN Document Server

    Aleksandrov, A V; Kot, N K; Andrighetto, A; Stroe, L

    2001-01-01

    The design and experimental results of the RIB source prototype are presented.A source will have the container of sup 2 sup 3 sup 5 U compounds heated up to 2200-2500 degree C. Vapors of uranium fission obtained when the ion source is irradiated by the high-energy neutron flux, are then ionized and extracted from the source. In the experiments with the prototype loaded by sup 1 sup 2 C the source working temperature 2700 degree C was reached, the carbon ion current 10 nA was obtained. The total operation time of more than 100 hours with no performance degradation was demonstrated.

  17. Prototype of an excimer laser for microprocessing

    Science.gov (United States)

    Iwanejko, Leszek; Pokora, Ludwik J.; Wolinski, Wieslaw L.

    1991-08-01

    The paper presents a brief description of a prototype of a XeC1 excimer laser for micraprocessing of materials. The planned main parameters of the laserare as follows: wavelength . . . . . . . . . . . . . . . . . . . . . . . . . 308 nm -''energyofapulse. . . . . . . . . . . . . lOOmJ -pulseduration (FWHM) . . . . . . . . . . . . . . . 2Ons repetition frequency . . . . . . . . . . . . . . 1O Hz peak power of a pulse . . . . . . . . . . . . . . . 5 MW With respect to currently carrried works with the prototype we show only preliminary results of testing of a laser head. The obtained maximum laser pulse energy exceeded 90 ml. However it should be pointed out that this value was obtained without any opt i mi z at i on of the 1 aser.

  18. Prototype ion source for JT-60 neutral beam injectors

    International Nuclear Information System (INIS)

    Akiba, M.

    1981-01-01

    A prototype ion source for JT-60 neutral beam injectors has been fabricated and tested. Here, we review the construction of the prototype ion source and report the experimental results about the source characteristics that has been obtained at this time. The prototype ion source is now installed at the prototype unit of JT-60 neutral beam injection units and the demonstration of the performances of the ion source and the prototype unit has just started

  19. ABOUT MODERN TECHNICAL GRAPHICS USING IN THE VIRTUAL PROTOTYPING

    OpenAIRE

    GHERGHINA George; POPA Dragos; BOGDAN Mihaela; GLUGA Cristian

    2008-01-01

    The paper presents aspects concerning the using of modern technical graphics elements in the virtual prototyping. The virtual prototyping is a process which uses a virtual prototype in place of physical prototype for the testing and the evaluation of specific features of designed product. The virtual prototype is created by computer such as it could assign the specific features as close as possible to the real conditions which permit its function simulation in the conditions for which is desi...

  20. The Economic Importance of Mineral Production in Iran, Pakistan and Turkey in View of Co-operation in Mineral Exports and Interregional Trade*

    Directory of Open Access Journals (Sweden)

    Zeki Doğan

    1968-06-01

    Full Text Available Possibilities of co-operation are discussed regarding exports of mineral commodities, namely, chromite and marble which are produced by the three regional countries.  In order to improve the opportunities for the regional trade among Iran, Pakistan and Turkey, the following minerals can offer potentialities: coking coal, sulphur, barite, bentonite, magnesite, lead and zinc ores and boron minerals, which are in short supply in one country and abundant in another.

  1. Outlook 96: Minerals and Energy

    International Nuclear Information System (INIS)

    1996-01-01

    Papers discussing the future of Australia's minerals and energy are presented under the following headings: Australia in the global minerals and energy markets; minerals exploration; steelmaking raw materials; aluminium and alumina; gold; nickel; base metals; titanium minerals; energy for a sustainable future; electricity; electricity in Asia; crude oil; coal trade; natural gas in Australia and uranium. Relevant papers are individually indexed/abstracted. Tabs., figs., refs

  2. International availability of energy minerals

    Energy Technology Data Exchange (ETDEWEB)

    White, N A [Norman White Associates, London (UK)

    1979-06-01

    Whereas the ultimate world supply of energy minerals - defined as fossil fuels and fissile minerals - is controlled by geological factors, the actual supply at any particular time is controlled by economic feasibility, technological innovations and/or political decisions. This paper identifies and discusses the principal uncertainties surrounding the international availability of energy minerals from now until the end of the century. A brief comparison is also made between energy and non-energy minerals.

  3. Aggregates from mineral wastes

    Directory of Open Access Journals (Sweden)

    Baic Ireneusz

    2016-01-01

    Full Text Available The problem concerning the growing demand for natural aggregates and the need to limit costs, including transportation from remote deposits, cause the increase in growth of interest in aggregates from mineral wastes as well as in technologies of their production and recovery. The paper presents the issue related to the group of aggregates other than natural. A common name is proposed for such material: “alternative aggregates”. The name seems to be fully justified due to adequacy of this term because of this raw materials origin and role, in comparison to the meaning of natural aggregates based on gravel and sand as well as crushed stones. The paper presents characteristics of the market and basic application of aggregates produced from mineral wastes, generated in the mining, power and metallurgical industries as well as material from demolished objects.

  4. The bismuth miners study

    International Nuclear Information System (INIS)

    Grosche, B.; Kreuzer, M.; Kreisheimer, M.; Schnelzer, M.; Tschense, A.; Gottschalk, K.

    2005-01-01

    The Federal Radiation Protection Office carried out a retrospective cohort study on some 60,000 former employees of the SAG/SDAG Wismut. The purpose of the study was to validate the radon-related risk of acquiring lung cancer previously calculated from 11 jointly evaluated studies among miners on the basis of an independent, homogeneous data record of comparable size. A further goal was to study the risk of acquiring extrapulmonal tumours. This paper only briefly describes the sampling, design and methods used in the study, as these were already presented during the Radon Status Talks. The first follow-up on the cohort was completed in 2003. Around this time a job exposure matrix (JEM) suitable for scientific inquiries was made available by the professional miners' association and the roof organisation of professional trade associations (HVBG). This paper is the first to report on the outcome of the risk analysis in direct comparison with the results found by BEIR

  5. Rock and mineral magnetism

    CERN Document Server

    O’Reilly, W

    1984-01-01

    The past two decades have witnessed a revolution in the earth sciences. The quantitative, instrument-based measurements and physical models of. geophysics, together with advances in technology, have radically transformed the way in which the Earth, and especially its crust, is described. The study of the magnetism of the rocks of the Earth's crust has played a major part in this transformation. Rocks, or more specifically their constituent magnetic minerals, can be regarded as a measuring instrument provided by nature, which can be employed in the service of the earth sciences. Thus magnetic minerals are a recording magnetometer; a goniometer or protractor, recording the directions of flows, fields and forces; a clock; a recording thermometer; a position recorder; astrain gauge; an instrument for geo­ logical surveying; a tracer in climatology and hydrology; a tool in petrology. No instrument is linear, or free from noise and systematic errors, and the performance of nature's instrument must be assessed and ...

  6. Characterization lithium mineralized pegmatite

    International Nuclear Information System (INIS)

    Pereira, E.F.S.; Luz Ferreira, O. da; Cancado, R.Z.L.

    1986-01-01

    Lithium economic importance has increased in the last years. In Brazil its reserves, generally pegmatites bodies, are found in Itinga-Aracuai-MG. This study of characterization belongs to a global plan of lithium mineralized bodies research of 'Arqueana de Minerios e Metais Ltda', which purpose is to give subsidies for implementation of pegmatite unit, in order to make better use of them. (F.E.) [pt

  7. Remote sensing of geologic mineral occurrences for the Colorado mineral belt using LANDSAT data

    Science.gov (United States)

    Carpenter, R. H. (Principal Investigator); Trexler, D. W.

    1976-01-01

    The author has identified the following significant results. LANDSAT imagery was examined as a practical and productive tool for mineral exploration along the Colorado Mineral Belt. An attempt was made to identify all large, active and/or abandoned mining districts on the imagery which initially were discovered by surface manifestations. A number of strong photolinements, circular features, and color anomalies were identified. Some of these form a part of the structural and igneous volcanic framework in which mineral deposits occur. No specific mineral deposits such as veins or porphyries were identified. Promising linear and concentric features were field checked at several locations. Some proved to be fault zones and calderas; others were strictly topographic features related to stream or glacial entrenchment. The Silverton Caldera region and the Idaho Springs-Central City district were chosen and studied as case histories to evaluate the application of LANDSAT imagery to mineral exploration. Evidence of specific mineralization related to ore deposits in these two areas were observed only on low level photography.

  8. Global mineral resource assessment: porphyry copper assessment of Mexico: Chapter A in Global mineral resource assessment

    Science.gov (United States)

    Hammarstrom, Jane M.; Robinson, Gilpin R.; Ludington, Steve; Gray, Floyd; Drenth, Benjamin J.; Cendejas-Cruz, Francisco; Espinosa, Enrique; Pérez-Segura, Efrén; Valencia-Moreno, Martín; Rodríguez-Castañeda, José Luis; Vásquez-Mendoza, Rigobert; Zürcher, Lukas

    2010-01-01

    Mineral resource assessments provide a synthesis of available information about distributions of mineral deposits in the Earth’s crust. A probabilistic mineral resource assessment of undiscovered resources in porphyry copper deposits in Mexico was done as part of a global mineral resource assessment. The purpose of the study was to (1) delineate permissive areas (tracts) for undiscovered porphyry copper deposits within 1 km of the surface at a scale of 1:1,000,000; (2) provide a database of known porphyry copper deposits and significant prospects; (3) estimate numbers of undiscovered deposits within those permissive tracts; and (4) provide probabilistic estimates of amounts of copper (Cu), molybdenum (Mo), gold (Au), and silver (Ag) that could be contained in undiscovered deposits for each permissive tract. The assessment was conducted using a three-part form of mineral resource assessment based on mineral deposit models (Singer, 1993). Delineation of permissive tracts primarily was based on distributions of mapped igneous rocks related to magmatic arcs that formed in tectonic settings associated with subduction boundary zones. Using a GIS, map units were selected from digital geologic maps based on lithology and age to delineate twelve permissive tracts associated with Jurassic, Laramide (~90 to 34 Ma), and younger Tertiary magmatic arcs. Stream-sediment geochemistry, mapped alteration, regional aeromagnetic data, and exploration history were considered in conjunction with descriptive deposit models and grade and tonnage models to guide estimates.

  9. 76 FR 6110 - Conflict Minerals

    Science.gov (United States)

    2011-02-03

    ...-10] RIN 3235-AK84 Conflict Minerals AGENCY: Securities and Exchange Commission. ACTION: Proposed rule...'') and would require any such issuer for which conflict minerals are necessary to the functionality or... body of its annual report whether its conflict minerals originated in the Democratic Republic of the...

  10. Flotation of sulphide minerals 1990

    Energy Technology Data Exchange (ETDEWEB)

    Forssberg, K S.E. [ed.; Luleaa University of Technology, Luleaa (Sweden). Division of Mineral Processing

    1991-01-01

    A total of 27 papers presented at the workshop on flotation of sulphide minerals, reprinted from the International Journal of Mineral Processing, vol. 33, nos. 1-4, are included in this book. They cover various aspects of flotation of such minerals as chalcopyrite, pyrrhotite, galena, malachite and pyrite.

  11. Digital mineral logging system

    International Nuclear Information System (INIS)

    West, J.B.

    1980-01-01

    A digital mineral logging system acquires data from a mineral logging tool passing through a borehole and transmits the data uphole to an electronic digital signal processor. A predetermined combination of sensors, including a deviometer, is located in a logging tool for the acquisition of the desired data as the logging tool is raised from the borehole. Sensor data in analog format is converted in the logging tool to a digital format and periodically batch transmitted to the surface at a predetermined sampling rate. An identification code is provided for each mineral logging tool, and the code is transmitted to the surface along with the sensor data. The self-identifying tool code is transmitted to the digital signal processor to identify the code against a stored list of the range of numbers assigned to that type of tool. The data is transmitted up the d-c power lines of the tool by a frequency shift key transmission technique. At the surface, a frequency shift key demodulation unit transmits the decoupled data to an asynchronous receiver interfaced to the electronic digital signal processor. During a recording phase, the signals from the logging tool are read by the electronic digital signal processor and stored for later processing. During a calculating phase, the stored data is processed by the digital signal processor and the results are outputted to a printer or plotter, or both

  12. Geoethical approach to mineral activities in Antarctica

    Science.gov (United States)

    Talalay, Pavel

    2013-04-01

    Antarctica is the outermost from civilization space continent. From 14.0 million km2 of surface area about 98% of Antarctica is covered by ice that averages at least 1.6 km in thickness. Geologically, the continent is the least explored in the world, and it is almost absolutely unknown what mineral resources Antarctica has as they are buried in rock that is covered by a thick ice sheet. It is thought to have large and valuable mineral deposits under the ice. This is because of what has been found in samples taken from the small areas of rock that are exposed, and also from what has been found in South Africa and South America. Up until 180 million years ago, Antarctica was a part of the Gondwanaland super continent, attached to South America, the Southern part of Africa, India and Australia, these continents then drifted apart until they reached their current positions. This leads to a possibility that Antarctica may also share some of the mineral wealth of these continents. Right now on the ice-free areas of Antarctica iron ore, chromium, copper, gold, nickel, platinum, coal and hydrocarbons have been found. The Protocol on Environmental Protection to the Antarctic Treaty, also known as the Madrid Protocol, was signed in 1991 by the signatories to the Antarctic Treaty and became law in January 1998. The Protocol provides for comprehensive protection of the Antarctic environment and associated ecosystems and includes a ban on all commercial mining for at least fifty years (this is up for review in 2041). Current climate change and melting ice in Polar Regions is opening up new opportunities to exploit mineral and oil resources. Even Antarctica's weather, ice and distance from any industrialized areas mean that mineral extraction would be extremely expensive and also extremely dangerous, the depletion of mineral recourses on the Earth can reverse banning of mining in Antarctica in future. There is no question that any resource exploitation in Antarctica will cause

  13. Fe-Impregnated Mineral Colloids for Peroxide Activation: Effects of Mineral Substrate and Fe Precursor.

    Science.gov (United States)

    Li, Yue; Machala, Libor; Yan, Weile

    2016-02-02

    Heterogeneous iron species at the mineral/water interface are important catalysts for the generation of reactive oxygen species at circumneutral pH. One significant pathway leading to the formation of such species arises from deposition of dissolved iron onto mineral colloids due to changes in redox conditions. This study investigates the catalytic properties of Fe impregnated on silica, alumina, and titania nanoparticles (as prototypical mineral colloids). Fe impregnation was carried out by immersing the mineral nanoparticles in dilute Fe(II) or Fe(III) solutions at pH 6 and 3, respectively, in an aerobic environment. The uptake of iron per unit surface area follows the order of nTiO2 > nAl2O3 > nSiO2 for both types of Fe precursors. Impregnation of mineral particles in Fe(II) solutions results in predominantly Fe(III) species due to efficient surface-mediated oxidation. The catalytic activity of the impregnated solids to produce hydroxyl radical (·OH) from H2O2 decomposition was evaluated using benzoic acid as a probe compound under dark conditions. Invariably, the rates of benzoic acid oxidation with different Fe-laden particles increase with the surface density of Fe until a critical density above which the catalytic activity approaches a plateau, suggesting active Fe species are formed predominantly at low surface loadings. The critical surface density of Fe varies with the mineral substrate as well as the aqueous Fe precursor. Fe impregnated on TiO2 exhibits markedly higher activity than its Al2O3 and SiO2 counterparts. The speciation of interfacial Fe is analyzed with diffuse reflectance UV-vis analysis and interpretation of the data in the context of benzoic oxidation rates suggests that the surface activity of the solids for ·OH generation correlates strongly with the isolated (i.e., mononuclear) Fe species. Therefore, iron dispersed on mineral colloids is a significant form of reactive iron surfaces in the aquatic environment.

  14. Petalet prototype for the ATLAS silicon strip detector upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Sperlich, Dennis [Humboldt-Universitaet zu Berlin (Germany); Gregor, Ingrid-Maria; Bloch, Ingo; Keller, John Stakely; Lohwasser, Kristin; Poley, Louise; Zakharchuk, Nataliia; Diez Cornell, Sergio [DESY (Germany); Hauser, Marc Manuel; Mori, Riccardo; Kuehl, Susanne; Parzefall, Ulrich [Albert-Ludwigs Universitaet Freiburg (Germany)

    2015-07-01

    To achieve more precise measurements and to search new physics phenomena, the luminosity at the LHC is expected to be increased during a series of upgrades in the next years. The latest scheduled upgrade, called the High Luminosity LHC (HL-LHC) is proposed to provide instantaneous luminosity of 5 x 10{sup 34} cm{sup 2}s{sup -1}. The increased luminosity and the radiation damage will affect the current Inner Tracker. In order to cope with the higher radiation dose and occupancy, the ATLAS experiment plans to replace the current Inner Detector with a new all-silicon tracker consisting of ∝8 m{sup 2} pixel and ∝192 m{sup 2} strip detectors. In response to the needs, highly modular structures will be used for the strip system, called Staves for the barrel region and Petals for the end-caps region. A small-scaled prototype for the Petal, the Petalet, is built to study some specialties of this complex wedge-shaped structures. The Petalet consists of one large and two small sized sensors. This report focuses on the recent progress in the prototyping of the Petalet and their electrical performances.

  15. Design, Prototyping and Control of a Flexible Cystoscope for Biomedical Applications

    Science.gov (United States)

    Sozer, Canberk; Ghorbani, Morteza; Alcan, Gokhan; Uvet, Huseyin; Unel, Mustafa; Kosar, Ali

    2017-07-01

    Kidney stone and prostate hyperplasia are very common urogenital diseases all over the world. To treat these diseases, one of the ESWL (Extracorporeal Shock Wave Lithotripsy), PCNL (Percutaneous Nephrolithotomy), cystoscopes or open surgery techniques can be used. Cystoscopes named devices are used for in-vivo intervention. A flexible or rigid cystoscope device is inserted into human body and operates on interested area. In this study, a flexible cystoscope prototype has been developed. The prototype is able to bend up to ±40°in X and Y axes, has a hydrodynamic cavitation probe for rounding sharp edges of kidney stone or resection of the filled prostate with hydrodynamic cavitation method and contains a waterproof medical camera to give visual feedback to the operator. The operator steers the flexible end-effector via joystick toward target region. This paper presents design, manufacturing, control and experimental setup of the tendon driven flexible cystoscope prototype. The prototype is 10 mm in outer diameter, 70 mm in flexible part only and 120 mm in total length with flexible part and rigid tube. The experimental results show that the prototype bending mechanism, control system, manufactured prototype parts and experimental setup function properly. A small piece of real kidney stone was broken in targeted area.

  16. Methods of mineral potential assessment of uranium deposits: A mineral systems approach

    International Nuclear Information System (INIS)

    Jaireth, S.

    2014-01-01

    Mineral potential represents the likelihood (probability) that an economic mineral deposit could have formed in an area. Mineral potential assessment and prospectivity analysis use a probabilistic concepts to mineral deposits, where the probability of an event (formation of a mineral deposit) is conditional on two factors : i) geological processes occurring in the area, and ii) the presence of geological features indicative of those process. For instance, one of the geological processes critical for the formation of sandstone-hosted uranium deposits in an area is transport of uranium in groundwaters. Geological features indicative of this process in an area comprise, i) presence of leachable source rocks of uranium; ii) presence of highly permeable sandstone; and iii) suitable hydrogeological gradient driving flow groundwaters. Mineral deposits can also be conceptualised as mineral systems with more emphasis on mineralising processes. This concept has some clear parallels with the petroleum systems approach which has proven to be a useful in oil and gas exploration. Mineral systems are defined as ‘all geological factors that control the generation and preservation of mineral deposits’. Seven important geological factors are outlined to define the characteristics of a hydrothermal mineral system. These factors include: i) source of the mineralising fluids and transporting legends; ii) source of metals and other ore components; iii) migration pathways which may include inflow as well as outflow zones; iv) thermal gradients; v) source of energy to mobilised fluids; vi) mechanical and structural focusing mechanism at the trap site; and vii) chemical and/or physical cause for precipitation of ore minerals at the trap site. This approach, commonly known as the ‘source’, ‘transport’ and ‘trap’ paradigm has been redefined to introduce five questions as a basis to understand spatial and temporal evolution of a mineral system at all scales (regional to

  17. Minerals from Morvan; Les mineraux du Morvan

    Energy Technology Data Exchange (ETDEWEB)

    Bayle, L.D

    2007-07-01

    Morvan is a mountainous and wooded region of Bourgogne (Burgundy, France) which represents the NE end of the French Massif central. The geologic history of this area has been propitious to the setting up of numerous ore deposits: iron, fluor, manganese, lead, barium and uranium. Morvan is the cradle of the French uranium industry. This book presents, first, the geology, geodynamics and ore deposits of Morvan, the history of the discovery of autunite and the exploitation of uranium. The three uranium mining districts are reviewed with the list of uranium minerals. The uranium exploitation activity was abandoned in 1990. An overview of a dozen of fluorine, barytine, lead and silver-bearing ore deposits is presented as well. A summary of all other mineral species associated to the granitic, metamorphic and volcanic areas of the region is proposed. (J.S.)

  18. Ceramic microfabrication by rapid prototyping process chains

    Indian Academy of Sciences (India)

    Ceramic microfabrication by rapid prototyping process chains ... is nearly impossible, shaping has to be done by a replication step in the green, unfired state. ... This process chain combines the fast and inexpensive supply of master models by ...

  19. Pancultural nostalgia : Prototypical conceptions across cultures

    NARCIS (Netherlands)

    Hepper, Erica G.; Wildschut, Tim; Sedikides, Constantine; Ritchie, Timothy D.; Yung, Yiu-Fai; Hansen, Nina; Abakoumkin, Georgios; Arikan, Gizem; Cisek, Sylwia Z.; Demassosso, Didier B.; Gebauer, Jochen E.; Gerber, J. P.; Gonzalez, Roberto; Kusumi, Takashi; Misra, Girishwar; Rusu, Mihaela; Ryan, Oisin; Stephan, Elena; Vingerhoets, Ad J. J.; Zhou, Xinyue

    2014-01-01

    Nostalgia is a frequently experienced complex emotion, understood by laypersons in the United Kingdom and United States of America to (a) refer prototypically to fond, self-relevant, social memories and (b) be more pleasant (e.g., happy, warm) than unpleasant (e.g., sad, regretful). This research

  20. Ares I-X Ground Diagnostic Prototype

    Science.gov (United States)

    Schwabacher, Mark A.; Martin, Rodney Alexander; Waterman, Robert D.; Oostdyk, Rebecca Lynn; Ossenfort, John P.; Matthews, Bryan

    2010-01-01

    The automation of pre-launch diagnostics for launch vehicles offers three potential benefits: improving safety, reducing cost, and reducing launch delays. The Ares I-X Ground Diagnostic Prototype demonstrated anomaly detection, fault detection, fault isolation, and diagnostics for the Ares I-X first-stage Thrust Vector Control and for the associated ground hydraulics while the vehicle was in the Vehicle Assembly Building at Kennedy Space Center (KSC) and while it was on the launch pad. The prototype combines three existing tools. The first tool, TEAMS (Testability Engineering and Maintenance System), is a model-based tool from Qualtech Systems Inc. for fault isolation and diagnostics. The second tool, SHINE (Spacecraft Health Inference Engine), is a rule-based expert system that was developed at the NASA Jet Propulsion Laboratory. We developed SHINE rules for fault detection and mode identification, and used the outputs of SHINE as inputs to TEAMS. The third tool, IMS (Inductive Monitoring System), is an anomaly detection tool that was developed at NASA Ames Research Center. The three tools were integrated and deployed to KSC, where they were interfaced with live data. This paper describes how the prototype performed during the period of time before the launch, including accuracy and computer resource usage. The paper concludes with some of the lessons that we learned from the experience of developing and deploying the prototype.

  1. ALICE TRD results from prototype tests

    CERN Document Server

    Andronic, A; Blume, C; Braun-Munzinger, P; Bucher, D; Catanescu, G; Ciobanu, M; Daues, H W; Devismes, A; Finck, C; Herrmann, N; Lister, T A; Mahmoud, Tariq; Peitzmann, Thomas; Petrovici, M; Reygers, K; Santo, R; Schicker, R; Sedykha, S; Simon, R S; Stachel, J; Stelzer, H; Wessels, J P; Winkelmann, O; Windelband, B; Xu, C

    2002-01-01

    We present results from tests of a prototype of the TRD for the ALICE experiment at LHC. We investigate the performance-of different radiator types, composed of foils, fibres and foams. The pion rejection performance for different methods of analysis over a momentum range from 0.7 to 2 GeV/c is presented. (8 refs).

  2. Integrating Rapid Prototyping into Graphic Communications

    Science.gov (United States)

    Xu, Renmei; Flowers, Jim

    2015-01-01

    Integrating different science, technology, engineering, and mathematics (STEM) areas can help students learn and leverage both the equipment and expertise at a single school. In comparing graphic communications classes with classes that involve rapid prototyping (RP) technologies like 3D printing, there are sufficient similarities between goals,…

  3. Diagnostics of the BIOMASS feed array prototype

    DEFF Research Database (Denmark)

    Cappellin, Cecilia; Pivnenko, Sergey; Pontoppidan, Kennie Nybo

    2013-01-01

    The 3D reconstruction algorithm is applied to the prototype feed array of the BIOMASS synthetic aperture radar, recently measured at the DTU-ESA Spherical Near-Field Antenna Test Facility in Denmark. Careful analysis of the measured feed array data has shown that the test support structure...

  4. Design of railway obstacle detection prototype

    CSIR Research Space (South Africa)

    Xungu, Sipho A

    2017-11-01

    Full Text Available Survey Inspection Device (SID) test prototype platform to serve as an early warning system for locomotives and was to travel 2km ahead of a locomotive in order to inspect the railway for possible obstacles such as human beings, livestock and collisions...

  5. Modelling cloud data for prototype manufacturing

    NARCIS (Netherlands)

    Liu, G.H.; Wong, Y.S.; Zhang, Y.F.; Loh, H.T.

    2003-01-01

    In this paper, the authors have developed a novel method to integrate reverse engineering (RE) and rapid prototyping (RP). Unorganised cloud data are directly sliced and modelled with two-dimensional (2D) cross-sections. Based on such a 2D CAD model, the data points are directly converted into RP

  6. Utilizing Rapid Prototyping for Architectural Modeling

    Science.gov (United States)

    Kirton, E. F.; Lavoie, S. D.

    2006-01-01

    This paper will discuss our approach to, success with and future direction in rapid prototyping for architectural modeling. The premise that this emerging technology has broad and exciting applications in the building design and construction industry will be supported by visual and physical evidence. This evidence will be presented in the form of…

  7. Marine Natural Products as Prototype Agrochemical Agents

    Science.gov (United States)

    Peng, Jiangnan; Shen, Xiaoyu; El Sayed, Khalid A.; Dunbar, D. C Harles; Perry, Tony L.; Wilkins, Scott P.; Hamann, Mark T.; Bobzin, Steve; Huesing, Joseph; Camp, Robin; Prinsen, Mike; Krupa, Dan; Wideman, Margaret A.

    2016-01-01

    In the interest of identifying new leads that could serve as prototype agrochemical agents, 18 structurally diverse marine-derived compounds were examined for insecticidal, herbicidal, and fungicidal activities. Several new classes of compounds have been shown to be insecticidal, herbicidal, and fungicidal, which suggests that marine natural products represent an intriguing source for the discovery of new agrochemical agents. PMID:12670165

  8. Performance evaluation of prototype mechanical cassava harvester ...

    African Journals Online (AJOL)

    Large-scale cassava harvesting, especially during the dry season, is a major constraint to its industrial demand and commercial production. Manual harvesting is slow and ... Results from field trials showed prototype harvesters weighing 268 – 310 kg can achieve optimum performance on ridged landforms. When harvested ...

  9. Using Affinity Diagrams to Evaluate Interactive Prototypes

    DEFF Research Database (Denmark)

    Lucero, Andrés

    2015-01-01

    our particular use of affinity diagramming in prototype evaluations. We reflect on a decade’s experience using affinity diagramming across a number of projects, both in industry and academia. Our affinity diagramming process in interaction design has been tailored and consists of four stages: creating...

  10. SONG - getting ready for the prototype

    DEFF Research Database (Denmark)

    Grundahl, F.; Christensen-Dalsgaard, J.; Jørgensen, Uffe Gråe

    2011-01-01

    . At each of the network nodes a 1 m telescope with a high-resolution spectrograph and two lucky-imaging cameras is placed. The instruments and telescope, for the prototype node, are currently being built and installation at Observatorio del Teide, Tenerife, Spain is foreseen for early 2011....

  11. SIMS Prototype System 4: performance test report

    Energy Technology Data Exchange (ETDEWEB)

    1978-10-09

    The results obtained during testing of a self-contained, preassembled air type solar system, designed for installation remote from the dwelling, to provide space heating and hot water are presented. Data analysis is included which documents the system performance and verifies the suitability of SIMS Prototype System 4 for field installation.

  12. Prototype-based models in machine learning

    NARCIS (Netherlands)

    Biehl, Michael; Hammer, Barbara; Villmann, Thomas

    2016-01-01

    An overview is given of prototype-based models in machine learning. In this framework, observations, i.e., data, are stored in terms of typical representatives. Together with a suitable measure of similarity, the systems can be employed in the context of unsupervised and supervised analysis of

  13. Installation package - SIMS prototype system 1A

    Science.gov (United States)

    1976-01-01

    This report consists of details for the installation, operation and maintenance of a prototype heating and hot water system, designed for residential or light commercial applications. This system consists of the following subsystems: air type collectors, pebble bed thermal storage, air handling unit, air to water heat exchanger, hot water preheat tank, auxiliary energy, ducting system.

  14. Prototype HL-LHC magnet undergoes testing

    CERN Multimedia

    Corinne Pralavorio

    2016-01-01

    A preliminary short prototype of the quadrupole magnets for the High-Luminosity LHC has passed its first tests.   The first short prototype of the quadrupole magnet for the High Luminosity LHC. (Photo: G. Ambrosio (US-LARP and Fermilab), P. Ferracin and E. Todesco (CERN TE-MSC)) Momentum is gathering behind the High-Luminosity LHC (HL-LHC) project. In laboratories on either side of the Atlantic, a host of tests are being carried out on the various magnet models. In mid-March, a short prototype of the quadrupole magnet underwent its first testing phase at the Fermilab laboratory in the United States. This magnet is a pre-prototype of the quadrupole magnets that will be installed near to the ATLAS and CMS detectors to squeeze the beams before collisions. Six quadrupole magnets will be installed on each side of each experiment, giving a total of 24 magnets, and will replace the LHC's triplet magnets. Made of superconducting niobium-tin, the magnets will be more powerful than their p...

  15. Mixed reality for neurosurgery: a novel prototype.

    Science.gov (United States)

    Alcañiz Raya, Mariano; Varvaro Marcinek, Hugo; Martinez Saez, José Miguel; Torres Sanchez, Roque; Juan Lizandra, M Carmen; Monserrat Aranda, Carlos; Gil Gomez, José Antonio

    2003-01-01

    Microscopes and neuronavigators are often used in neurosurgical procedures. Our Mixed Reality prototype proposes to show neuronavigator imaging overlayed onto the surgical field of view. The proposal is to replace the traditional optical microscope with a digital one. The system is presented in this article. Firsts trials have been performed at the laboratory with satisfactory results.

  16. Virtual Reality for Prototyping Service Journeys

    Directory of Open Access Journals (Sweden)

    Costas Boletsis

    2018-04-01

    Full Text Available The use of virtual elements for developing new service prototyping environments and more realistic simulations has been suggested as a way to optimise the service prototyping process. This work examines the application of virtual reality (VR in prototyping service journeys and it hypothesises that VR can recreate service journeys in a highly immersive, agile, and inexpensive manner, thus allowing users to have a representative service experience and enabling service designers to extract high-quality user feedback. To that end, a new service prototyping method, called VR service walkthrough, is presented and evaluated through an empirical comparative study. A VR service walkthrough is a virtual simulation of a service journey, representing how the service unfolds over space and time. A comparative study between the VR service walkthrough method and an adapted service walkthrough method evaluates the application of both methods using a location-based audio tour guide service as a case study. Two user groups (each with 21 users were used to evaluate both methods based on two factors: the user experience they offered and the subjective meaningfulness and quality of feedback they produced. Results show that the VR service walkthrough method gave a performance similar to that of the service walkthrough method. It was also able to communicate the service concept in an immersive way and foster constructive feedback.

  17. Classroom Evaluation of a Rapid Prototyping System.

    Science.gov (United States)

    Tennyson, Stephen A.; Krueger, Thomas J.

    2001-01-01

    Introduces rapid prototyping which creates virtual models through a variety of automated material additive processes. Relates experiences using JP System 5 in freshman and sophomore engineering design graphics courses. Analyzes strengths and limitations of the JP System 5 and discusses how to use it effectively. (Contains 15 references.)…

  18. Systems Prototyping with Fourth Generation Tools.

    Science.gov (United States)

    Sholtys, Phyllis

    1983-01-01

    The development of information systems using an engineering approach that uses both traditional programing techniques and fourth generation software tools is described. Fourth generation applications tools are used to quickly develop a prototype system that is revised as the user clarifies requirements. (MLW)

  19. A prototype imaging second harmonic interferometer

    International Nuclear Information System (INIS)

    Jobes, F.C.; Bretz, N.L.

    1997-01-01

    We have built a prototype imaging second harmonic interferometer, which is intended to test critical elements of a design for a tangential array interferometer on C-Mod 6 . The prototype uses a pulsed, 35 mJ, 10 Hz multimode, Nd:YAG laser, LiB 3 O 5 doublers, a fan beam created by a cylindrical lens, four retroreflector elements, and a CCD camera as a detector. The prototype also uses a polarization scheme in which the interference information is eventually carried by two second harmonic beams with crossed polarization. These are vector summed and differenced, and separated, by a Wollaston prism, to give two spots on the CCD. There is a pair of these spots for each retroreflector used. The phase information is directly available as the ratio of the difference to sum the intensities of the two spots. We have tested a single channel configuration of this prototype, varying the phase by changing the pressure in an air cell, and we have obtained a 5:1 light to dark ratio, and a clear sinusoidal variation of the ratio as a function of pressure change. copyright 1997 American Institute of Physics

  20. Column Stores as an IR Prototyping Tool

    NARCIS (Netherlands)

    H.F. Mühleisen (Hannes); T. Samar (Thaer); J.J.P. Lin (Jimmy); A.P. de Vries (Arjen)

    2014-01-01

    textabstract. We make the suggestion that instead of implementing custom index structures and query evaluation algorithms, IR researchers should simply store document representations in a column-oriented relational database and write ranking models using SQL. For rapid prototyping, this is

  1. Development of industrial minerals in Colorado

    Science.gov (United States)

    Arbogast, Belinda F.; Knepper, Daniel H.; Langer, William H.; Cappa, James A.; Keller, John W.; Widmann, Beth L.; Ellefsen, Karl J.; Klein, Terry L.; Lucius, Jeffrey E.; Dersch, John S.

    2011-01-01

    Technology and engineering have helped make mining safer and cleaner for both humans and the environment. Inevitably, mineral development entails costs as well as benefits. Developing a mine is an environmental, engineering, and planning challenge that must conform to many Federal, State, and local regulations. Community collaboration, creative design, and best management practices of sustainability and biodiversity can be positive indicators for the mining industry. A better understanding of aesthetics, culture, economics, geology, climate, vegetation and wildlife, topography, historical significance, and regional land planning is important in resolving land-use issues and managing mineral resources wisely. Ultimately, the consuming public makes choices about product use (including water, food, highways, housing, and thousands of other items) that influence operations of the mineral industry. Land planners, resource managers, earth scientists, designers, and public groups have a responsibility to consider sound scientific information, society's needs, and community appeals in making smart decisions concerning resource use and how complex landscapes should change. An effort to provide comprehensive geosciences data for land management agencies in central Colorado was undertaken in 2003 by scientists of the U.S. Geological Survey and the Colorado Geological Survey. This effort, the Central Colorado Assessment Project, addressed a variety of land-use issues: an understanding of the availability of industrial and metallic rocks and minerals, the geochemical and environmental effects of historic mining activity on surface water and groundwater, and the geologic controls on the availability and quality of groundwater. The USDA Forest Service and other land management agencies have the opportunity to contribute to the sustainable management of natural aggregate and other mineral resources through the identification and selective development of mineral resources and the

  2. The experiment progress of bracket brazing to SSMIC for the ITER ELM prototype coil

    Energy Technology Data Exchange (ETDEWEB)

    Shi, Yi, E-mail: shiyi@ipp.ac.cn; Wu, Yu; Jin, Huan; Ren, Zhibin; Han, Houxiang; Qian, Jing; Qian, Li; Liu, Bo

    2014-11-15

    Highlights: • In this study, the experimental research of brackets brazing to stainless steel jacketed, Mineral Insulated Conductor (SSMIC) of the first Edge Localized Modes (ELMs) prototype coil for ITER has been made. • The technology for controlling the fluidity of silver-based brazing alloy is developed to meet the bracket brazing. • Brazing experiments to find the reason for cracks are carried out and the improved brazing technologies to restrain the cracks in the Inconel 625 jacket with silver-based alloy are developed. - Abstract: The first Edge Localized Modes (ELMs) prototype coil for International Thermonuclear Experimental Reactor (ITER) has been manufactured in the Institute of Plasma Physics, CAS (ASIPP) at 2014. The all 19 brackets need to braze to the stainless steel jacketed, Mineral Insulated Conductor (SSMIC) for transporting the nuclear heating in the brackets to the water-cooled SSMIC. Silver-based alloy is the only candidate brazing filler for the bracket brazing due to the limitation from melting point temperature and strength. In this paper, firstly, the experimental study for controlling the fluidity of silver-based brazing alloy is developed. And then, the brazing experiment of prototype bracket is introduced to develop the brazing process and some cracks in the Inconel 625 jackets surface appeared unexpectedly. The microstructures and tensile performance study of the cracked Inconel 625 jacket were made to explore the reason for cracks and the improved brazing technologies to suppress the cracks are developed. Finally, the bracket brazing experiment for the first ELM prototype coil is carried out, In spite of this, some cracks also appear in the Inconel 625 jackets.

  3. The experiment progress of bracket brazing to SSMIC for the ITER ELM prototype coil

    International Nuclear Information System (INIS)

    Shi, Yi; Wu, Yu; Jin, Huan; Ren, Zhibin; Han, Houxiang; Qian, Jing; Qian, Li; Liu, Bo

    2014-01-01

    Highlights: • In this study, the experimental research of brackets brazing to stainless steel jacketed, Mineral Insulated Conductor (SSMIC) of the first Edge Localized Modes (ELMs) prototype coil for ITER has been made. • The technology for controlling the fluidity of silver-based brazing alloy is developed to meet the bracket brazing. • Brazing experiments to find the reason for cracks are carried out and the improved brazing technologies to restrain the cracks in the Inconel 625 jacket with silver-based alloy are developed. - Abstract: The first Edge Localized Modes (ELMs) prototype coil for International Thermonuclear Experimental Reactor (ITER) has been manufactured in the Institute of Plasma Physics, CAS (ASIPP) at 2014. The all 19 brackets need to braze to the stainless steel jacketed, Mineral Insulated Conductor (SSMIC) for transporting the nuclear heating in the brackets to the water-cooled SSMIC. Silver-based alloy is the only candidate brazing filler for the bracket brazing due to the limitation from melting point temperature and strength. In this paper, firstly, the experimental study for controlling the fluidity of silver-based brazing alloy is developed. And then, the brazing experiment of prototype bracket is introduced to develop the brazing process and some cracks in the Inconel 625 jackets surface appeared unexpectedly. The microstructures and tensile performance study of the cracked Inconel 625 jacket were made to explore the reason for cracks and the improved brazing technologies to suppress the cracks are developed. Finally, the bracket brazing experiment for the first ELM prototype coil is carried out, In spite of this, some cracks also appear in the Inconel 625 jackets

  4. Minerals and rumen function

    International Nuclear Information System (INIS)

    Smith, R.H.

    1984-01-01

    The mechanisms are discussed of some clinical disorders, characteristic only of ruminants and related to the effects of abnormal mineral intake on rumen function. With particular attention to tropical conditions, consideration is given to: (a) the possible effects of phosphorus deficiency on rumen microbial activity; (b) the depression of rumen microbial synthesis in sulphur deficiency; (c) the inhibition of magnesium absorption from the forestomachs; and (d) the involvement of the rumen microorganisms in leading to copper and vitamin B 12 deficiencies as a result of low intakes of cobalt. (author)

  5. Reducing coal miner absenteeism

    Energy Technology Data Exchange (ETDEWEB)

    Peters, R.H.; Clingan, M.R. (Bureau of Mines, PA (USA). Pittsburgh Research Center)

    1989-09-01

    High absenteeism at coal mines can seriously affect safety and hamper productivity. Several effective strategies for achieving high attendance which mine operators may not have considered are presented and a method is proposed for implementing programs for minimizing absenteeism among coal miners. The best strategies for improving attendance will vary according to the needs and circumstances of the particular mine, however, the process for establishing such a program is relatively invariant. A four-stage process is recommended; evaluate data from prior attendance records, communicate attendance goals and policy, develop and implement an attendance promotion program, and recycle. 12 refs., 5 figs.

  6. United States mineral resources

    Science.gov (United States)

    Brobst, Donald A.; Pratt, Walden P.

    1973-01-01

    The work on this volume began in January 1972, but in a broader sense its production began many years ago. The chapters were written by geologists most of whom have had many years of experience studying the geology of mineral deposits, and more particularly the commodities about which they have written here. A total of nearly 2,300 man-years of professional experience in the geology of mineral resources is represented by the authors of the volume, and about 30 man-years went directly into its preparation. Each chapter contains not only a synthesis of the state of knowledge of the geology of the commodity, but also an appraisal of the known resources, and an examination of the geologic possibilities for finding additional deposits. In January 1972, responsibility for the preparation of the volume was assigned to us as co-editors, and we were given a tentative list of commodities and authors. We provided each author with a suggested outline of general topics to be covered, and some guidelines as to scope and philosophy of approach, but beyond that we avoided any attempt to fit each chapter into a stereotype. Moreover, the types of commodities range from the major metals and industrial minerals such as copper, silver, and fluorspar, which have been the subject of geologic research for years, to other commodities that are of such varied geologic nature (such as pigments or gemstones) or of such minor present importance (such as scandium or thallium) that they cannot be treated from the same viewpoint as the major minerals. The chapters range, therefore, from comprehensive summary reports to general essays that reflect the individuality of the authors as well as the variation among commodities. Throughout the book the emphasis is on geology, but each chapter contains some summary information on uses, technology, and economics. These summaries are not meant to be exhaustive, however, and additional details are in the 1970 edition of "Mineral Facts and Problems" (Bulletin

  7. Refining mineral oils

    Energy Technology Data Exchange (ETDEWEB)

    1946-07-05

    A process is described refining raw oils such as mineral oils, shale oils, tar, their fractions and derivatives, by extraction with a selected solvent or a mixture of solvents containing water, forming a solvent more favorable for the hydrocarbons poor in hydrogen than for hydrocarbons rich in hydrogen, this process is characterized by the addition of an aiding solvent for the water which can be mixed or dissolved in the water and the solvent or in the dissolving mixture and increasing in this way the solubility of the water in the solvent or the dissolving mixture.

  8. RELATIVE TRACE MINERAL BIOAVAILABILITY

    OpenAIRE

    Rchard D. Miles; Peter R. Henry

    2006-01-01

    Para determinar a eficiência de utilização de elementos minerais dietéticos, deve-se conhecer a biodisponibilidade relativa de cada elemento de um determinado ingrediente ou de uma ração completa. Análises químicas da dieta ou de um determinado ingrediente não indicam a efetividade biológica de um nutriente. Existem muitos fatores que influenciam a biodisponibilidade dos minerais, especialmente dos minerais-traço, tais como: nível de consumo do mineral, forma química, digestibilidade da dieta...

  9. A single-neuron tracing study of arkypallidal and prototypic neurons in healthy rats.

    Science.gov (United States)

    Fujiyama, Fumino; Nakano, Takashi; Matsuda, Wakoto; Furuta, Takahiro; Udagawa, Jun; Kaneko, Takeshi

    2016-12-01

    The external globus pallidus (GP) is known as a relay nucleus of the indirect pathway of the basal ganglia. Recent studies in dopamine-depleted and healthy rats indicate that the GP comprises two main types of pallidofugal neurons: the so-called "prototypic" and "arkypallidal" neurons. However, the reconstruction of complete arkypallidal neurons in healthy rats has not been reported. Here we visualized the entire axonal arborization of four single arkypallidal neurons and six single prototypic neurons in rat brain using labeling with a viral vector expressing membrane-targeted green fluorescent protein and examined the distribution of axon boutons in the target nuclei. Results revealed that not only the arkypallidal neurons but nearly all of the prototypic neurons projected to the striatum with numerous axon varicosities. Thus, the striatum is a major target nucleus for pallidal neurons. Arkypallidal and prototypic GP neurons located in the calbindin-positive and calbindin-negative regions mainly projected to the corresponding positive and negative regions in the striatum. Because the GP and striatum calbindin staining patterns reflect the topographic organization of the striatopallidal projection, the striatal neurons in the sensorimotor and associative regions constitute the reciprocal connection with the GP neurons in the corresponding regions.

  10. Operating characteristics of a prototype high energy gamma-ray telescope

    International Nuclear Information System (INIS)

    Jenkins, T.L.; Frye, G.M.; Hall, C.J.; Owens, A.; Pendleton, G.N.; Carter, J.N.; Ramsden, D.; Agrinier, B.; Bonfand, E.; Refloch, A.; Tabary, A.

    1985-08-01

    We have operated a prototype coded aperture telescope in a tagged photon beam ranging in energy from 23 to 123 MeV. The purpose of the experiment was to demonstrate the feasibility of operating a coded aperture mask telescope in this energy region. This paper reports some preliminary results and conclusions drawn from some of the data resulting from this experiment

  11. Indoor Free Space Optic: a new prototype, realization and evaluation

    Science.gov (United States)

    Bouchet, Olivier; Besnard, Pascal; Mihaescu, Adrian

    2008-08-01

    The Free Space Optic (FSO) communication is a daily reality used by an increasing number of companies. For indoor environment, optical wireless communication becomes a good alternative with respect to radio proposals. For both technologies, the architecture is similar: emission/reception base station (Gateway or Bridge) are installed to cover zones, which are defined to ensure a quality of service. The customers may be connected to the Wireless Local Area Network (WLAN) with an adapter or module that emits and receives on this network. But due to its specific characteristics, wireless optical technology could present important advantages such as: Transmitted data security, medical immunity, high data rate, etc... Nevertheless, the optical system may have a limit on the network management aspect and link budget. The scope of this paper is to present a proposal at crossroads between optical fibre telecom system and data processing. In this document, we will present a prototype developed in Brittany during a regional collaborative project (Techim@ges). In order to answer to the management aspect and the link budget, this prototype uses an optical multiplexing technique in 1550 nm band: the Wavelength Division Multiple Access (WDMA). Moreover it also proposes a new class 1 high power emission solution. This full duplex system transmits these various wavelengths in free space, by using optical Multiplexer/Demultiplexer and optical modules. Each module has a defined and personal wavelength associated to the terminal identification (addresses MAC or IP). This approach permits a data rate at a minimum of a ten's Mbit/s per customer and potentially hundred Mbps for a line of sight system. The application field for the achieved and proposed prototype is potentially investigated from WLAN to WPAN.

  12. PEAR: Prototyping Expressive Animated Robots - A framework for social robot prototyping

    OpenAIRE

    Balit , Etienne; Vaufreydaz , Dominique; Reignier , Patrick

    2018-01-01

    International audience; Social robots are transitioning from lab experiments to commercial products, creating new needs for proto-typing and design tools. In this paper, we present a framework to facilitate the prototyping of expressive animated robots. For this, we start by reviewing the design of existing social robots in order to define a set of basic components of social robots. We then show how to extend an existing 3D animation software to enable the animation of these components. By co...

  13. Analysis of trace and mineral elements in vanilla pods from the region of S.A.V.A using total reflection X-ray fluorescence, atomic absorption and ion chromatography techniques

    International Nuclear Information System (INIS)

    Be, K.

    2013-01-01

    In the case of studies of food security, - arsenic, cobalt, chromium, copper, iron, manganese, nickel, rubidium, selenium, strontium, titanium, zinc - cadmium, lead - are almost always analyzed. Guide values are used to express the level of quality in matter of consumption. Analytical laboratories of Madagascar-INSTN outline usually their research on quantifying those elements by using two different analytical methods, the Total Reflection X-Ray Fluorescence for the first twelve metals and the Atomic Absorption Spectrometry dedicated to lead and cadmium. Supplementary analysis is carried out for the quantification of essential mineral elements such as calcium, magnesium and potassium by using Ion Chromatograph. The aim of this study was to set up the analysis of the above mentioned elements in vanilla pods collected from Sambava, Antalaha and Andapa for a routine use. After all the parameters were established, the validation was particularly focused on the limits of detection and quantification and the accuracy of each element. The used methods fulfil the scope of application needed and are easy to use in routine. [fr

  14. Aggregate and Mineral Resources - MO 2014 Industrial Mineral Mines (SHP)

    Data.gov (United States)

    NSGIC State | GIS Inventory — This data set contains names, locations and additional data for active Industrial Mineral Mines permitted with the Missouri Department of Natural Resources, Division...

  15. Regionalism, Regionalization and Regional Development

    Directory of Open Access Journals (Sweden)

    Liviu C. Andrei

    2016-03-01

    Full Text Available Sustained development is a concept associating other concepts, in its turn, in the EU practice, e.g. regionalism, regionalizing and afferent policies, here including structural policies. This below text, dedicated to integration concepts, will limit on the other hand to regionalizing, otherwise an aspect typical to Europe and to the EU. On the other hand, two aspects come up to strengthen this field of ideas, i.e. the region (al-regionalism-(regional development triplet has either its own history or precise individual outline of terms.

  16. Assessment of industrial minerals and rocks in the controlled area

    International Nuclear Information System (INIS)

    Castor, S.B.; Lock, D.E.

    1996-01-01

    Yucca Mountain in Nye County, Nevada, is a potential site for a permanent repository for high-level nuclear waste in Miocene ash flow tuff. The Yucca Mountain controlled area occupies approximately 98 km 2 that includes the potential repository site. The Yucca Mountain controlled area is located within the southwestern Nevada volcanic field, a large area of Miocene volcanism that includes at least four major calderas or cauldrons. It is sited on a remnant of a Neogene volcanic plateau that was centered around the Timber Mountain caldera complex. The Yucca Mountain region contains many occurrences of valuable or potentially valuable industrial minerals, including deposits with past or current production of construction aggregate, borate minerals, clay, building stone, fluorspar, silicate, and zeolites. The existence of these deposits in the region and the occurrence of certain mineral materials at Yucca Mountain, indicate that the controlled area may have potential for industrial mineral and rock deposits. Consideration of the industrial mineral potential within the Yucca Mountain controlled area is mainly based on petrographic and lithologic studies of samples from drill holes in Yucca Mountain. Clay minerals, zeolites, fluorite, and barite, as minerals that are produced economically in Nevada, have been identified in samples from drill holes in Yucca Mountain

  17. Assessment of industrial minerals and rocks in the controlled area

    Energy Technology Data Exchange (ETDEWEB)

    Castor, S.B. [Nevada Bureau of Mines and Geology, Reno, NV (United States); Lock, D.E. [Mackay School of Mines, Reno, NV (United States)

    1996-08-01

    Yucca Mountain in Nye County, Nevada, is a potential site for a permanent repository for high-level nuclear waste in Miocene ash flow tuff. The Yucca Mountain controlled area occupies approximately 98 km{sup 2} that includes the potential repository site. The Yucca Mountain controlled area is located within the southwestern Nevada volcanic field, a large area of Miocene volcanism that includes at least four major calderas or cauldrons. It is sited on a remnant of a Neogene volcanic plateau that was centered around the Timber Mountain caldera complex. The Yucca Mountain region contains many occurrences of valuable or potentially valuable industrial minerals, including deposits with past or current production of construction aggregate, borate minerals, clay, building stone, fluorspar, silicate, and zeolites. The existence of these deposits in the region and the occurrence of certain mineral materials at Yucca Mountain, indicate that the controlled area may have potential for industrial mineral and rock deposits. Consideration of the industrial mineral potential within the Yucca Mountain controlled area is mainly based on petrographic and lithologic studies of samples from drill holes in Yucca Mountain. Clay minerals, zeolites, fluorite, and barite, as minerals that are produced economically in Nevada, have been identified in samples from drill holes in Yucca Mountain.

  18. Interoperability prototype between hospitals and general practitioners in Switzerland.

    Science.gov (United States)

    Alves, Bruno; Müller, Henning; Schumacher, Michael; Godel, David; Abu Khaled, Omar

    2010-01-01

    Interoperability in data exchange has the potential to improve the care processes and decrease costs of the health care system. Many countries have related eHealth initiatives in preparation or already implemented. In this area, Switzerland has yet to catch up. Its health system is fragmented, because of the federated nature of cantons. It is thus more difficult to coordinate efforts between the existing healthcare actors. In the Medicoordination project a pragmatic approach was selected: integrating several partners in healthcare on a regional scale in French speaking Switzerland. In parallel with the Swiss eHealth strategy, currently being elaborated by the Swiss confederation, particularly medium-sized hospitals and general practitioners were targeted in Medicoordination to implement concrete scenarios of information exchange between hospitals and general practitioners with a high added value. In this paper we focus our attention on a prototype implementation of one chosen scenario: the discharge summary. Although simple in concept, exchanging release letters shows small, hidden difficulties due to the multi-partner nature of the project. The added value of such a prototype is potentially high and it is now important to show that interoperability can work in practice.

  19. Divertor cassette movers prototypes for ITER

    International Nuclear Information System (INIS)

    Bogusch, E.; Batz, R.; Bieber, O.; Gottfried, R.; Cerdan, G.

    1998-01-01

    Following competitive tendering, in October 1996 Siemens was contracted by the European Commission to design and supply an assembly of four Divertor Cassette Movers Prototypes including the control and command systems for the movers proper. The assembly consisting of one Cassette Toroidal Mover (CTM), one Radial Mover Tractor (TRC), one Second Cassette Carrier (SCC), and one Radial Cassette Carrier (RCC) represents key components of the Divertor Test Platform at Brasimone, one of the seven large R+D projects for ITER. By detailed design, high-precision manufacturing and testing of these devices, Siemens contributed to the verification of an important task within the European R and D program towards ITER construction. Replacement of the divertor cassettes is a scheduled maintenance operation throughout the life of ITER. The successful fabrication and testing of the Divertor Cassette Movers Prototypes is all important milestone to verify this delicate operation. (authors)

  20. ECCE Toolkit: Prototyping Sensor-Based Interaction

    Directory of Open Access Journals (Sweden)

    Andrea Bellucci

    2017-02-01

    Full Text Available Building and exploring physical user interfaces requires high technical skills and hours of specialized work. The behavior of multiple devices with heterogeneous input/output channels and connectivity has to be programmed in a context where not only the software interface matters, but also the hardware components are critical (e.g., sensors and actuators. Prototyping physical interaction is hindered by the challenges of: (1 programming interactions among physical sensors/actuators and digital interfaces; (2 implementing functionality for different platforms in different programming languages; and (3 building custom electronic-incorporated objects. We present ECCE (Entities, Components, Couplings and Ecosystems, a toolkit for non-programmers that copes with these issues by abstracting from low-level implementations, thus lowering the complexity of prototyping small-scale, sensor-based physical interfaces to support the design process. A user evaluation provides insights and use cases of the kind of applications that can be developed with the toolkit.