Proposal for Requirement Validation Criteria and Method Based on Actor Interaction

Science.gov (United States)

Hattori, Noboru; Yamamoto, Shuichiro; Ajisaka, Tsuneo; Kitani, Tsuyoshi

We propose requirement validation criteria and a method based on the interaction between actors in an information system. We focus on the cyclical transitions of one actor's situation against another and clarify observable stimuli and responses based on these transitions. Both actors' situations can be listed in a state transition table, which describes the observable stimuli or responses they send or receive. Examination of the interaction between both actors in the state transition tables enables us to detect missing or defective observable stimuli or responses. Typically, this method can be applied to the examination of the interaction between a resource managed by the information system and its user. As a case study, we analyzed 332 requirement defect reports of an actual system development project in Japan. We found that there were a certain amount of defects regarding missing or defective stimuli and responses, which can be detected using our proposed method if this method is used in the requirement definition phase. This means that we can reach a more complete requirement definition with our proposed method.

Applicability of the proposed evaluation method for social infrastructures to nuclear power plants

International Nuclear Information System (INIS)

Ichimura, Tomiyasu

2015-01-01

This study proposes an evaluation method for social infrastructures, and verifies the applicability of the proposed evaluation method to social infrastructures by applying it to nuclear power plants, which belong to social infrastructures. In the proposed evaluation method for social infrastructures, the authors chose four evaluation viewpoints and proposed common evaluation standards for the evaluation indexes obtained from each viewpoint. By applying this system to the evaluation of nuclear power plants, the evaluation index examples were obtained from the evaluation viewpoints. Furthermore, when the level of the common evaluation standards of the proposed evaluation method was applied to the evaluation of the activities of nuclear power plants based on the regulations, it was confirmed that these activities are at the highest level. Through this application validation, it was clarified that the proposed evaluation method for social infrastructures had certain effectiveness. The four evaluation viewpoints are 'service,' 'environment,' 'action factor,' and 'operation and management.' Part of the application examples to a nuclear power plant are as follows: (1) in the viewpoint of service: the operation rate of the power plant, and operation costs, and (2) in the viewpoint of environment: external influence related to nuclear waste and radioactivity, and external effect related to cooling water. (A.O.)

Methodological proposal for environmental impact evaluation since different specific methods

International Nuclear Information System (INIS)

Leon Pelaez, Juan Diego; Lopera Arango Gabriel Jaime

1999-01-01

Some conceptual and practical elements related to environmental impact evaluation are described and related to the preparation of technical reports (environmental impact studies and environmental management plans) to be presented to environmental authorities for obtaining the environmental permits for development projects. In the first part of the document a summary of the main aspects of normative type is made that support the studies of environmental impact in Colombia. We propose a diagram for boarding and elaboration of the evaluation of environmental impact, which begins with the description of the project and of the environmental conditions in the area of the same. Passing then to identify the impacts through a method matricial and continuing with the quantitative evaluation of the same. For which we propose the use of the method developed by Arboleda (1994). Also we propose to qualify the activities of the project and the components of the environment in their relative importance, by means of a method here denominated agglomerate evaluation. Which allows finding those activities more impacting and the mostly impacted components. Lastly it is presented some models for the elaboration and presentation of the environmental management plans. The pursuit programs and those of environmental supervision

SU-F-J-86: Method to Include Tissue Dose Response Effect in Deformable Image Registration

Energy Technology Data Exchange (ETDEWEB)

Zhu, J; Liang, J; Chen, S; Qin, A; Yan, D [Beaumont Health Systeml, Royal Oak, MI (United States)

2016-06-15

Purpose: Organ changes shape and size during radiation treatment due to both mechanical stress and radiation dose response. However, the dose response induced deformation has not been considered in conventional deformable image registration (DIR). A novel DIR approach is proposed to include both tissue elasticity and radiation dose induced organ deformation. Methods: Assuming that organ sub-volume shrinkage was proportional to the radiation dose induced cell killing/absorption, the dose induced organ volume change was simulated applying virtual temperature on each sub-volume. Hence, both stress and heterogeneity temperature induced organ deformation. Thermal stress finite element method with organ surface boundary condition was used to solve deformation. Initial boundary correspondence on organ surface was created from conventional DIR. Boundary condition was updated by an iterative optimization scheme to minimize elastic deformation energy. The registration was validated on a numerical phantom. Treatment dose was constructed applying both the conventional DIR and the proposed method using daily CBCT image obtained from HN treatment. Results: Phantom study showed 2.7% maximal discrepancy with respect to the actual displacement. Compared with conventional DIR, subvolume displacement difference in a right parotid had the mean±SD (Min, Max) to be 1.1±0.9(−0.4∼4.8), −0.1±0.9(−2.9∼2.4) and −0.1±0.9(−3.4∼1.9)mm in RL/PA/SI directions respectively. Mean parotid dose and V30 constructed including the dose response induced shrinkage were 6.3% and 12.0% higher than those from the conventional DIR. Conclusion: Heterogeneous dose distribution in normal organ causes non-uniform sub-volume shrinkage. Sub-volume in high dose region has a larger shrinkage than the one in low dose region, therefore causing more sub-volumes to move into the high dose area during the treatment course. This leads to an unfavorable dose-volume relationship for the normal organ

A method proposal for cumulative environmental impact assessment based on the landscape vulnerability evaluation

International Nuclear Information System (INIS)

Pavlickova, Katarina; Vyskupova, Monika

2015-01-01

Cumulative environmental impact assessment deals with the occasional use in practical application of environmental impact assessment process. The main reasons are the difficulty of cumulative impact identification caused by lack of data, inability to measure the intensity and spatial effect of all types of impacts and the uncertainty of their future evolution. This work presents a method proposal to predict cumulative impacts on the basis of landscape vulnerability evaluation. For this purpose, qualitative assessment of landscape ecological stability is conducted and major vulnerability indicators of environmental and socio-economic receptors are specified and valuated. Potential cumulative impacts and the overall impact significance are predicted quantitatively in modified Argonne multiple matrixes while considering the vulnerability of affected landscape receptors and the significance of impacts identified individually. The method was employed in the concrete environmental impact assessment process conducted in Slovakia. The results obtained in this case study reflect that this methodology is simple to apply, valid for all types of impacts and projects, inexpensive and not time-consuming. The objectivity of the partial methods used in this procedure is improved by quantitative landscape ecological stability evaluation, assignment of weights to vulnerability indicators based on the detailed characteristics of affected factors, and grading impact significance. - Highlights: • This paper suggests a method proposal for cumulative impact prediction. • The method includes landscape vulnerability evaluation. • The vulnerability of affected receptors is determined by their sensitivity. • This method can increase the objectivity of impact prediction in the EIA process

Proposed frustrated-total-reflection acoustic sensing method

International Nuclear Information System (INIS)

Hull, J.R.

1981-01-01

Modulation of electromagnetic energy transmission through a frustrated-total-reflection device by pressure-induced changes in the index of refraction is proposed for use as an acoustic detector. Maximum sensitivity occurs for angles of incidence near the critical angle. The minimum detectable pressure in air is limited by Brownian noise. Acoustic propagation losses and diffraction of the optical beam by the acoustic signal limit the minimum acoustic wavelength to lengths of the order of the spatial extent of the optical beam. The response time of the method is fast enough to follow individual acoustic waves

Membrane for distillation including nanostructures, methods of making membranes, and methods of desalination and separation

KAUST Repository

Lai, Zhiping; Huang, Kuo-Wei; Chen, Wei

2016-01-01

In accordance with the purpose(s) of the present disclosure, as embodied and broadly described herein, embodiments of the present disclosure provide membranes, methods of making the membrane, systems including the membrane, methods of separation, methods of desalination, and the like.

Membrane for distillation including nanostructures, methods of making membranes, and methods of desalination and separation

KAUST Repository

Lai, Zhiping

2016-01-21

In accordance with the purpose(s) of the present disclosure, as embodied and broadly described herein, embodiments of the present disclosure provide membranes, methods of making the membrane, systems including the membrane, methods of separation, methods of desalination, and the like.

Proposed waste form performance criteria and testing methods for low-level mixed waste

International Nuclear Information System (INIS)

Franz, E.M.; Fuhrmann, M.; Bowerman, B.; Bates, S.; Peters, R.

1994-08-01

This document describes proposed waste form performance criteria and testing method that could be used as guidance in judging viability of a waste form as a physico-chemical barrier to releases of radionuclides and RCRA regulated hazardous components. It is assumed that release of contaminants by leaching is the single most important property by which the effectiveness of a waste form is judged. A two-tier regimen is proposed. The first tier includes a leach test required by the Environmental Protection Agency and a leach test designed to determine the net forward leach rate for a variety of materials. The second tier of tests are to determine if a set of stresses (i.e., radiation, freeze-thaw, wet-dry cycling) on the waste form adversely impact its ability to retain contaminants and remain physically intact. It is recommended that the first tier tests be performed first to determine acceptability. Only on passing the given specifications for the leach tests should other tests be performed. In the absence of site-specific performance assessments (PA), two generic modeling exercises are described which were used to calculate proposed acceptable leach rates

Proposal of a method for evaluating tsunami risk using response-surface methodology

Science.gov (United States)

Fukutani, Y.

2017-12-01

Information on probabilistic tsunami inundation hazards is needed to define and evaluate tsunami risk. Several methods for calculating these hazards have been proposed (e.g. Løvholt et al. (2012), Thio (2012), Fukutani et al. (2014), Goda et al. (2015)). However, these methods are inefficient, and their calculation cost is high, since they require multiple tsunami numerical simulations, therefore lacking versatility. In this study, we proposed a simpler method for tsunami risk evaluation using response-surface methodology. Kotani et al. (2016) proposed an evaluation method for the probabilistic distribution of tsunami wave-height using a response-surface methodology. We expanded their study and developed a probabilistic distribution of tsunami inundation depth. We set the depth (x1) and the slip (x2) of an earthquake fault as explanatory variables and tsunami inundation depth (y) as an object variable. Subsequently, tsunami risk could be evaluated by conducting a Monte Carlo simulation, assuming that the generation probability of an earthquake follows a Poisson distribution, the probability distribution of tsunami inundation depth follows the distribution derived from a response-surface, and the damage probability of a target follows a log normal distribution. We applied the proposed method to a wood building located on the coast of Tokyo Bay. We implemented a regression analysis based on the results of 25 tsunami numerical calculations and developed a response-surface, which was defined as y=ax1+bx2+c (a:0.2615, b:3.1763, c=-1.1802). We assumed proper probabilistic distribution for earthquake generation, inundation height, and vulnerability. Based on these probabilistic distributions, we conducted Monte Carlo simulations of 1,000,000 years. We clarified that the expected damage probability of the studied wood building is 22.5%, assuming that an earthquake occurs. The proposed method is therefore a useful and simple way to evaluate tsunami risk using a response

Estimation of body fluids with bioimpedance spectroscopy: state of the art methods and proposal of novel methods

International Nuclear Information System (INIS)

Buendia, R; Seoane, F; Lindecrantz, K; Bosaeus, I; Gil-Pita, R; Johannsson, G; Ellegård, L; Ward, L C

2015-01-01

Determination of body fluids is a useful common practice in determination of disease mechanisms and treatments. Bioimpedance spectroscopy (BIS) methods are non-invasive, inexpensive and rapid alternatives to reference methods such as tracer dilution. However, they are indirect and their robustness and validity are unclear. In this article, state of the art methods are reviewed, their drawbacks identified and new methods are proposed. All methods were tested on a clinical database of patients receiving growth hormone replacement therapy. Results indicated that most BIS methods are similarly accurate (e.g.  <  0.5   ±   3.0% mean percentage difference for total body water) for estimation of body fluids. A new model for calculation is proposed that performs equally well for all fluid compartments (total body water, extra- and intracellular water). It is suggested that the main source of error in extracellular water estimation is due to anisotropy, in total body water estimation to the uncertainty associated with intracellular resistivity and in determination of intracellular water a combination of both. (paper)

A qualitative method proposal to improve environmental impact assessment

International Nuclear Information System (INIS)

Toro, Javier; Requena, Ignacio; Duarte, Oscar; Zamorano, Montserrat

2013-01-01

In environmental impact assessment, qualitative methods are used because they are versatile and easy to apply. This methodology is based on the evaluation of the strength of the impact by grading a series of qualitative attributes that can be manipulated by the evaluator. The results thus obtained are not objective, and all too often impacts are eliminated that should be mitigated with corrective measures. However, qualitative methodology can be improved if the calculation of Impact Importance is based on the characteristics of environmental factors and project activities instead on indicators assessed by evaluators. In this sense, this paper proposes the inclusion of the vulnerability of environmental factors and the potential environmental impact of project activities. For this purpose, the study described in this paper defined Total Impact Importance and specified a quantification procedure. The results obtained in the case study of oil drilling in Colombia reflect greater objectivity in the evaluation of impacts as well as a positive correlation between impact values, the environmental characteristics at and near the project location, and the technical characteristics of project activities. -- Highlights: • Concept of vulnerability has been used to calculate the importance impact assessment. • This paper defined Total Impact Importance and specified a quantification procedure. • The method includes the characteristics of environmental and project activities. • The application has shown greater objectivity in the evaluation of impacts. • Better correlation between impact values, environment and the project has been shown

A qualitative method proposal to improve environmental impact assessment

Energy Technology Data Exchange (ETDEWEB)

Toro, Javier, E-mail: jjtoroca@unal.edu.co [Institute of Environmental Studies, National University of Colombia at Bogotá (Colombia); Requena, Ignacio, E-mail: requena@decsai.ugr.es [Department of Computer Science and Artificial Intelligence, University of Granada (Spain); Duarte, Oscar, E-mail: ogduartev@unal.edu.co [National University of Colombia at Bogotá, Department of Electrical Engineering and Electronics (Colombia); Zamorano, Montserrat, E-mail: zamorano@ugr.es [Department of Civil Engineering, University of Granada (Spain)

2013-11-15

In environmental impact assessment, qualitative methods are used because they are versatile and easy to apply. This methodology is based on the evaluation of the strength of the impact by grading a series of qualitative attributes that can be manipulated by the evaluator. The results thus obtained are not objective, and all too often impacts are eliminated that should be mitigated with corrective measures. However, qualitative methodology can be improved if the calculation of Impact Importance is based on the characteristics of environmental factors and project activities instead on indicators assessed by evaluators. In this sense, this paper proposes the inclusion of the vulnerability of environmental factors and the potential environmental impact of project activities. For this purpose, the study described in this paper defined Total Impact Importance and specified a quantification procedure. The results obtained in the case study of oil drilling in Colombia reflect greater objectivity in the evaluation of impacts as well as a positive correlation between impact values, the environmental characteristics at and near the project location, and the technical characteristics of project activities. -- Highlights: • Concept of vulnerability has been used to calculate the importance impact assessment. • This paper defined Total Impact Importance and specified a quantification procedure. • The method includes the characteristics of environmental and project activities. • The application has shown greater objectivity in the evaluation of impacts. • Better correlation between impact values, environment and the project has been shown.

Improved Riccati Transfer Matrix Method for Free Vibration of Non-Cylindrical Helical Springs Including Warping

Directory of Open Access Journals (Sweden)

A.M. Yu

2012-01-01

Full Text Available Free vibration equations for non-cylindrical (conical, barrel, and hyperboloidal types helical springs with noncircular cross-sections, which consist of 14 first-order ordinary differential equations with variable coefficients, are theoretically derived using spatially curved beam theory. In the formulation, the warping effect upon natural frequencies and vibrating mode shapes is first studied in addition to including the rotary inertia, the shear and axial deformation influences. The natural frequencies of the springs are determined by the use of improved Riccati transfer matrix method. The element transfer matrix used in the solution is calculated using the Scaling and Squaring method and Pad'e approximations. Three examples are presented for three types of springs with different cross-sectional shapes under clamped-clamped boundary condition. The accuracy of the proposed method has been compared with the FEM results using three-dimensional solid elements (Solid 45 in ANSYS code. Numerical results reveal that the warping effect is more pronounced in the case of non-cylindrical helical springs than that of cylindrical helical springs, which should be taken into consideration in the free vibration analysis of such springs.

Unsteady panel method for complex configurations including wake modeling

CSIR Research Space (South Africa)

Van Zyl, Lourens H

2008-01-01

Full Text Available implementations of the DLM are however not very versatile in terms of geometries that can be modeled. The ZONA6 code offers a versatile surface panel body model including a separated wake model, but uses a pressure panel method for lifting surfaces. This paper...

A Proposal of Operational Risk Management Method Using FMEA for Drug Manufacturing Computerized System

Science.gov (United States)

Takahashi, Masakazu; Nanba, Reiji; Fukue, Yoshinori

This paper proposes operational Risk Management (RM) method using Failure Mode and Effects Analysis (FMEA) for drug manufacturing computerlized system (DMCS). The quality of drug must not be influenced by failures and operational mistakes of DMCS. To avoid such situation, DMCS has to be conducted enough risk assessment and taken precautions. We propose operational RM method using FMEA for DMCS. To propose the method, we gathered and compared the FMEA results of DMCS, and develop a list that contains failure modes, failures and countermeasures. To apply this list, we can conduct RM in design phase, find failures, and conduct countermeasures efficiently. Additionally, we can find some failures that have not been found yet.

A proposal on evaluation method of neutron absorption performance to substitute conventional neutron attenuation test

International Nuclear Information System (INIS)

Kim, Je Hyun; Shim, Chang Ho; Kim, Sung Hyun; Choe, Jung Hun; Cho, In Hak; Park, Hwan Seo; Park, Hyun Seo; Kim, Jung Ho; Kim, Yoon Ho

2016-01-01

For a verification of newly-developed neutron absorbers, one of guidelines on the qualification and acceptance of neutron absorbers is the neutron attenuation test. However, this approach can cause a problem for the qualifications that it cannot distinguish how the neutron attenuates from materials. In this study, an estimation method of neutron absorption performances for materials is proposed to detect both direct penetration and back-scattering neutrons. For the verification of the proposed method, MCNP simulations with the experimental system designed in this study were pursued using the polyethylene, iron, normal glass and the vitrified form. The results show that it can easily test neutron absorption ability using single absorber model. Also, from simulation results of single absorber and double absorbers model, it is verified that the proposed method can evaluate not only the direct thermal neutrons passing through materials, but also the scattered neutrons reflected to the materials. Therefore, the neutron absorption performances can be accurately estimated using the proposed method comparing with the conventional neutron attenuation test. It is expected that the proposed method can contribute to increase the reliability of the performance of neutron absorbers

A proposal on evaluation method of neutron absorption performance to substitute conventional neutron attenuation test

Energy Technology Data Exchange (ETDEWEB)

Kim, Je Hyun; Shim, Chang Ho [Dept. of Nuclear Engineering, Hanyang University, Seoul (Korea, Republic of); Kim, Sung Hyun [Nuclear Fuel Cycle Waste Treatment Research Division, Research Reactor Institute, Kyoto University, Osaka (Japan); Choe, Jung Hun; Cho, In Hak; Park, Hwan Seo [Ionizing Radiation Center, Nuclear Fuel Cycle Waste Treatment Research Division, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Hyun Seo; Kim, Jung Ho; Kim, Yoon Ho [Ionizing Radiation Center, Korea Research Institute of Standards and Science, Daejeon (Korea, Republic of)

2016-12-15

For a verification of newly-developed neutron absorbers, one of guidelines on the qualification and acceptance of neutron absorbers is the neutron attenuation test. However, this approach can cause a problem for the qualifications that it cannot distinguish how the neutron attenuates from materials. In this study, an estimation method of neutron absorption performances for materials is proposed to detect both direct penetration and back-scattering neutrons. For the verification of the proposed method, MCNP simulations with the experimental system designed in this study were pursued using the polyethylene, iron, normal glass and the vitrified form. The results show that it can easily test neutron absorption ability using single absorber model. Also, from simulation results of single absorber and double absorbers model, it is verified that the proposed method can evaluate not only the direct thermal neutrons passing through materials, but also the scattered neutrons reflected to the materials. Therefore, the neutron absorption performances can be accurately estimated using the proposed method comparing with the conventional neutron attenuation test. It is expected that the proposed method can contribute to increase the reliability of the performance of neutron absorbers.

A proposal on alternative sampling-based modeling method of spherical particles in stochastic media for Monte Carlo simulation

Energy Technology Data Exchange (ETDEWEB)

Kim, Song Hyun; Lee, Jae Yong; KIm, Do Hyun; Kim, Jong Kyung [Dept. of Nuclear Engineering, Hanyang University, Seoul (Korea, Republic of); Noh, Jae Man [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-08-15

Chord length sampling method in Monte Carlo simulations is a method used to model spherical particles with random sampling technique in a stochastic media. It has received attention due to the high calculation efficiency as well as user convenience; however, a technical issue regarding boundary effect has been noted. In this study, after analyzing the distribution characteristics of spherical particles using an explicit method, an alternative chord length sampling method is proposed. In addition, for modeling in finite media, a correction method of the boundary effect is proposed. Using the proposed method, sample probability distributions and relative errors were estimated and compared with those calculated by the explicit method. The results show that the reconstruction ability and modeling accuracy of the particle probability distribution with the proposed method were considerably high. Also, from the local packing fraction results, the proposed method can successfully solve the boundary effect problem. It is expected that the proposed method can contribute to the increasing of the modeling accuracy in stochastic media.

A proposal on alternative sampling-based modeling method of spherical particles in stochastic media for Monte Carlo simulation

International Nuclear Information System (INIS)

Kim, Song Hyun; Lee, Jae Yong; KIm, Do Hyun; Kim, Jong Kyung; Noh, Jae Man

2015-01-01

Chord length sampling method in Monte Carlo simulations is a method used to model spherical particles with random sampling technique in a stochastic media. It has received attention due to the high calculation efficiency as well as user convenience; however, a technical issue regarding boundary effect has been noted. In this study, after analyzing the distribution characteristics of spherical particles using an explicit method, an alternative chord length sampling method is proposed. In addition, for modeling in finite media, a correction method of the boundary effect is proposed. Using the proposed method, sample probability distributions and relative errors were estimated and compared with those calculated by the explicit method. The results show that the reconstruction ability and modeling accuracy of the particle probability distribution with the proposed method were considerably high. Also, from the local packing fraction results, the proposed method can successfully solve the boundary effect problem. It is expected that the proposed method can contribute to the increasing of the modeling accuracy in stochastic media

Development of a quantitative safety assessment method for nuclear I and C systems including human operators

International Nuclear Information System (INIS)

Kim, Man Cheol

2004-02-01

pages of fault trees which should be redrawn from the logical relation between the components in the DPPS. On the other hand, the RGGG model for DPPS can be drawn in only I page, and the structure of the model is almost similar to the actual structure of DPPS. In addition, the RGGG model visually shows the state of information processed by each component. In this sense, I believe that the RGGG method is more intuitive and easy to use. Quantitative analysis of the fault tree model and the RGGG model shows that the two models produce equivalent results. Currently, an identified disadvantage is the calculation time, since a lot of approximation algorithms are already developed for the fault tree analysis, but not for the RGGG method. As a new method for HRA, I develop a quantitative situation assessment model for human operators, since human performance is mainly affected by the situation assessment. In contrast to the conventional HRA methods which are mostly developed by expert opinions, the proposed situation assessment model for human operators is developed on the basis of mathematical theories, Bayesian inference and the information theory, with the following two assumptions. 1. Human operators can do Bayesian inference, even though the results cannot be as accurate as mathematical calculations. 2. In knowledge-driven monitoring, the probability that human operators select an indicator as the next indicator to monitor is proportional to the expected information from the indicator. (The expected information from each indicator can be calculated using the information theory.) With an experiment, it is shown that the two assumptions are reasonable. The proposed mathematical model for the situation assessment of human operators is expected to be used as the basis for the development of the quantitative model for the situation assessment of actual human operators. By combining the RGGG method and the mathematical model for the situation assessment of human operators, I

78 FR 35929 - Proposed Listing of Additional Waters To Be Included on Indiana's 2010 List of Impaired Waters...

Science.gov (United States)

2013-06-14

... which existing technology-based pollution controls are not stringent enough to attain or maintain state... ENVIRONMENTAL PROTECTION AGENCY [FRL-9823-3] Proposed Listing of Additional Waters To Be Included...: Environmental Protection Agency (EPA). ACTION: Notice and request for comments. SUMMARY: This notice announces...

Catalyst support structure, catalyst including the structure, reactor including a catalyst, and methods of forming same

Science.gov (United States)

Van Norman, Staci A.; Aston, Victoria J.; Weimer, Alan W.

2017-05-09

Structures, catalysts, and reactors suitable for use for a variety of applications, including gas-to-liquid and coal-to-liquid processes and methods of forming the structures, catalysts, and reactors are disclosed. The catalyst material can be deposited onto an inner wall of a microtubular reactor and/or onto porous tungsten support structures using atomic layer deposition techniques.

Validation of a method for assessing resident physicians' quality improvement proposals.

Science.gov (United States)

Leenstra, James L; Beckman, Thomas J; Reed, Darcy A; Mundell, William C; Thomas, Kris G; Krajicek, Bryan J; Cha, Stephen S; Kolars, Joseph C; McDonald, Furman S

2007-09-01

Residency programs involve trainees in quality improvement (QI) projects to evaluate competency in systems-based practice and practice-based learning and improvement. Valid approaches to assess QI proposals are lacking. We developed an instrument for assessing resident QI proposals--the Quality Improvement Proposal Assessment Tool (QIPAT-7)-and determined its validity and reliability. QIPAT-7 content was initially obtained from a national panel of QI experts. Through an iterative process, the instrument was refined, pilot-tested, and revised. Seven raters used the instrument to assess 45 resident QI proposals. Principal factor analysis was used to explore the dimensionality of instrument scores. Cronbach's alpha and intraclass correlations were calculated to determine internal consistency and interrater reliability, respectively. QIPAT-7 items comprised a single factor (eigenvalue = 3.4) suggesting a single assessment dimension. Interrater reliability for each item (range 0.79 to 0.93) and internal consistency reliability among the items (Cronbach's alpha = 0.87) were high. This method for assessing resident physician QI proposals is supported by content and internal structure validity evidence. QIPAT-7 is a useful tool for assessing resident QI proposals. Future research should determine the reliability of QIPAT-7 scores in other residency and fellowship training programs. Correlations should also be made between assessment scores and criteria for QI proposal success such as implementation of QI proposals, resident scholarly productivity, and improved patient outcomes.

Proposal of Constraints Analysis Method Based on Network Model for Task Planning

Science.gov (United States)

Tomiyama, Tomoe; Sato, Tatsuhiro; Morita, Toyohisa; Sasaki, Toshiro

Deregulation has been accelerating several activities toward reengineering business processes, such as railway through service and modal shift in logistics. Making those activities successful, business entities have to regulate new business rules or know-how (we call them ‘constraints’). According to the new constraints, they need to manage business resources such as instruments, materials, workers and so on. In this paper, we propose a constraint analysis method to define constraints for task planning of the new business processes. To visualize each constraint's influence on planning, we propose a network model which represents allocation relations between tasks and resources. The network can also represent task ordering relations and resource grouping relations. The proposed method formalizes the way of defining constraints manually as repeatedly checking the network structure and finding conflicts between constraints. Being applied to crew scheduling problems shows that the method can adequately represent and define constraints of some task planning problems with the following fundamental features, (1) specifying work pattern to some resources, (2) restricting the number of resources for some works, (3) requiring multiple resources for some works, (4) prior allocation of some resources to some works and (5) considering the workload balance between resources.

78 FR 56695 - Proposed Listing of Additional Waters To Be Included on Indiana's 2010 List of Impaired Waters...

Science.gov (United States)

2013-09-13

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9900-95--Region 5] Proposed Listing of Additional Waters To Be Included on Indiana's 2010 List of Impaired Waters Under the Clean Water Act AGENCY: Environmental Protection Agency (EPA). ACTION: Reopening of comment period. SUMMARY: EPA is reopening the comment period...

Proposal for an Evaluation Method for the Performance of Work Procedures.

Science.gov (United States)

Mohammed, Mouda; Mébarek, Djebabra; Wafa, Boulagouas; Makhlouf, Chati

2016-12-01

Noncompliance of operators with work procedures is a recurrent problem. This human behavior has been said to be situational and studied by many different approaches (ergonomic and others), which consider the noncompliance with work procedures to be obvious and seek to analyze its causes as well as consequences. The object of the proposed method is to solve this problem by focusing on the performance of work procedures and ensuring improved performance on a continuous basis. This study has multiple results: (1) assessment of the work procedures' performance by a multicriteria approach; (2) the use of a continuous improvement approach as a framework for the sustainability of the assessment method of work procedures' performance; and (3) adaptation of the Stop-Card as a facilitator support for continuous improvement of work procedures. The proposed method emphasizes to put in value the inputs of continuous improvement of the work procedures in relation with the conventional approaches which adopt the obvious evidence of the noncompliance to the working procedures and seek to analyze the cause-effect relationships related to this unacceptable phenomenon, especially in strategic industry.

Proposed method to calculate FRMAC intervention levels for the assessment of radiologically contaminated food and comparison of the proposed method to the U.S. FDA's method to calculate derived intervention levels

Energy Technology Data Exchange (ETDEWEB)

Kraus, Terrence D.; Hunt, Brian D.

2014-02-01

This report reviews the method recommended by the U.S. Food and Drug Administration for calculating Derived Intervention Levels (DILs) and identifies potential improvements to the DIL calculation method to support more accurate ingestion pathway analyses and protective action decisions. Further, this report proposes an alternate method for use by the Federal Emergency Radiological Assessment Center (FRMAC) to calculate FRMAC Intervention Levels (FILs). The default approach of the FRMAC during an emergency response is to use the FDA recommended methods. However, FRMAC recommends implementing the FIL method because we believe it to be more technically accurate. FRMAC will only implement the FIL method when approved by the FDA representative on the Federal Advisory Team for Environment, Food, and Health.

A hardenability test proposal

Energy Technology Data Exchange (ETDEWEB)

Murthy, N.V.S.N. [Ingersoll-Rand (I) Ltd., Bangalore (India)

1996-12-31

A new approach for hardenability evaluation and its application to heat treatable steels will be discussed. This will include an overview and deficiencies of the current methods and discussion on the necessity for a new approach. Hardenability terminology will be expanded to avoid ambiguity and over-simplification as encountered with the current system. A new hardenability definition is proposed. Hardenability specification methods are simplified and rationalized. The new hardenability evaluation system proposed here utilizes a test specimen with varying diameter as an alternative to the cylindrical Jominy hardenability test specimen and is readily applicable to the evaluation of a wide variety of steels with different cross-section sizes.

Force measuring valve assemblies, systems including such valve assemblies and related methods

Science.gov (United States)

DeWall, Kevin George [Pocatello, ID; Garcia, Humberto Enrique [Idaho Falls, ID; McKellar, Michael George [Idaho Falls, ID

2012-04-17

Methods of evaluating a fluid condition may include stroking a valve member and measuring a force acting on the valve member during the stroke. Methods of evaluating a fluid condition may include measuring a force acting on a valve member in the presence of fluid flow over a period of time and evaluating at least one of the frequency of changes in the measured force over the period of time and the magnitude of the changes in the measured force over the period of time to identify the presence of an anomaly in a fluid flow and, optionally, its estimated location. Methods of evaluating a valve condition may include directing a fluid flow through a valve while stroking a valve member, measuring a force acting on the valve member during the stroke, and comparing the measured force to a reference force. Valve assemblies and related systems are also disclosed.

Optimal plot size in the evaluation of papaya scions: proposal and comparison of methods

Directory of Open Access Journals (Sweden)

Humberto Felipe Celanti

Full Text Available ABSTRACT Evaluating the quality of scions is extremely important and it can be done by characteristics of shoots and roots. This experiment evaluated height of the aerial part, stem diameter, number of leaves, petiole length and length of roots of papaya seedlings. Analyses were performed from a blank trial with 240 seedlings of "Golden Pecíolo Curto". The determination of the optimum plot size was done by applying the methods of maximum curvature, maximum curvature of coefficient of variation and a new proposed method, which incorporates the bootstrap resampling simulation to the maximum curvature method. According to the results obtained, five is the optimal number of seedlings of papaya "Golden Pecíolo Curto" per plot. The proposed method of bootstrap simulation with replacement provides optimal plot sizes equal or higher than the maximum curvature method and provides same plot size than maximum curvature method of the coefficient of variation.

Composite materials and bodies including silicon carbide and titanium diboride and methods of forming same

Science.gov (United States)

Lillo, Thomas M.; Chu, Henry S.; Harrison, William M.; Bailey, Derek

2013-01-22

Methods of forming composite materials include coating particles of titanium dioxide with a substance including boron (e.g., boron carbide) and a substance including carbon, and reacting the titanium dioxide with the substance including boron and the substance including carbon to form titanium diboride. The methods may be used to form ceramic composite bodies and materials, such as, for example, a ceramic composite body or material including silicon carbide and titanium diboride. Such bodies and materials may be used as armor bodies and armor materials. Such methods may include forming a green body and sintering the green body to a desirable final density. Green bodies formed in accordance with such methods may include particles comprising titanium dioxide and a coating at least partially covering exterior surfaces thereof, the coating comprising a substance including boron (e.g., boron carbide) and a substance including carbon.

The Proposal to “Snapshot” Raim Method for Gnss Vessel Receivers Working in Poor Space Segment Geometry

Directory of Open Access Journals (Sweden)

Nowak Aleksander

2015-12-01

Full Text Available Nowadays, we can observe an increase in research on the use of small unmanned autonomous vessel (SUAV to patrol and guiding critical areas including harbours. The proposal to “snapshot” RAIM (Receiver Autonomous Integrity Monitoring method for GNSS receivers mounted on SUAV operating in poor space segment geometry is presented in the paper. Existing “snapshot” RAIM methods and algorithms which are used in practical applications have been developed for airborne receivers, thus two main assumptions have been made. The first one is that the geometry of visible satellites is strong. It means that the exclusion of any satellite from the positioning solution don’t cause significant deterioration of Dilution of Precision (DOP coefficients. The second one is that only one outlier could appear in pseudorange measurements. In case of SUAV operating in harbour these two assumptions cannot be accepted. Because of their small dimensions, GNSS antenna is only a few decimetres above sea level and regular ships, buildings and harbour facilities block and reflect satellite signals. Thus, different approach to “snapshot” RAIM is necessary. The proposal to method based on analyses of allowable maximal separation of positioning sub-solutions with using some information from EGNOS messages is described in the paper. Theoretical assumptions and results of numerical experiments are presented.

Initiation devices, initiation systems including initiation devices and related methods

Energy Technology Data Exchange (ETDEWEB)

Daniels, Michael A.; Condit, Reston A.; Rasmussen, Nikki; Wallace, Ronald S.

2018-04-10

Initiation devices may include at least one substrate, an initiation element positioned on a first side of the at least one substrate, and a spark gap electrically coupled to the initiation element and positioned on a second side of the at least one substrate. Initiation devices may include a plurality of substrates where at least one substrate of the plurality of substrates is electrically connected to at least one adjacent substrate of the plurality of substrates with at least one via extending through the at least one substrate. Initiation systems may include such initiation devices. Methods of igniting energetic materials include passing a current through a spark gap formed on at least one substrate of the initiation device, passing the current through at least one via formed through the at least one substrate, and passing the current through an explosive bridge wire of the initiation device.

A proposed impact assessment method for genetically modified plants (AS-GMP Method)

International Nuclear Information System (INIS)

Jesus-Hitzschky, Katia Regina Evaristo de; Silveira, Jose Maria F.J. da

2009-01-01

An essential step in the development of products based on biotechnology is an assessment of their potential economic impacts and safety, including an evaluation of the potential impact of transgenic crops and practices related to their cultivation on the environment and human or animal health. The purpose of this paper is to provide an assessment method to evaluate the impact of biotechnologies that uses quantifiable parameters and allows a comparative analysis between conventional technology and technologies using GMOs. This paper introduces a method to perform an impact analysis associated with the commercial release and use of genetically modified plants, the Assessment System GMP Method. The assessment is performed through indicators that are arranged according to their dimension criterion likewise: environmental, economic, social, capability and institutional approach. To perform an accurate evaluation of the GMP specific indicators related to genetic modification are grouped in common fields: genetic insert features, GM plant features, gene flow, food/feed field, introduction of the GMP, unexpected occurrences and specific indicators. The novelty is the possibility to include specific parameters to the biotechnology under assessment. In this case by case analysis the factors of moderation and the indexes are parameterized to perform an available assessment.

77 FR 13131 - Proposed Collection: Comment Request Post-Award Reporting Requirements Including New Research...

Science.gov (United States)

2012-03-05

... submitted to the Office of Management and Budget (OMB) for review and approval. Proposed Collection: Title... Administration, Centers for Disease Control and Prevention, and Agency for Healthcare Research and Quality (AHRQ... information technology. FOR FURTHER INFORMATION CONTACT: To request more information on the proposed project...

A novel technique for including surface tension in PLIC-VOF methods

Energy Technology Data Exchange (ETDEWEB)

Meier, M.; Yadigaroglu, G. [Swiss Federal Institute of Technology, Nuclear Engineering Lab. ETH-Zentrum, CLT, Zurich (Switzerland); Smith, B. [Paul Scherrer Inst. (PSI), Villigen (Switzerland). Lab. for Thermal-Hydraulics

2002-02-01

Various versions of Volume-of-Fluid (VOF) methods have been used successfully for the numerical simulation of gas-liquid flows with an explicit tracking of the phase interface. Of these, Piecewise-Linear Interface Construction (PLIC-VOF) appears as a fairly accurate, although somewhat more involved variant. Including effects due to surface tension remains a problem, however. The most prominent methods, Continuum Surface Force (CSF) of Brackbill et al. and the method of Zaleski and co-workers (both referenced later), both induce spurious or 'parasitic' currents, and only moderate accuracy in regards to determining the curvature. We present here a new method to determine curvature accurately using an estimator function, which is tuned with a least-squares-fit against reference data. Furthermore, we show how spurious currents may be drastically reduced using the reconstructed interfaces from the PLIC-VOF method. (authors)

Proposal for a Five-Step Method to Elicit Expert Judgment

Directory of Open Access Journals (Sweden)

Duco Veen

2017-12-01

Full Text Available Elicitation is a commonly used tool to extract viable information from experts. The information that is held by the expert is extracted and a probabilistic representation of this knowledge is constructed. A promising avenue in psychological research is to incorporated experts’ prior knowledge in the statistical analysis. Systematic reviews on elicitation literature however suggest that it might be inappropriate to directly obtain distributional representations from experts. The literature qualifies experts’ performance on estimating elements of a distribution as unsatisfactory, thus reliably specifying the essential elements of the parameters of interest in one elicitation step seems implausible. Providing feedback within the elicitation process can enhance the quality of the elicitation and interactive software can be used to facilitate the feedback. Therefore, we propose to decompose the elicitation procedure into smaller steps with adjustable outcomes. We represent the tacit knowledge of experts as a location parameter and their uncertainty concerning this knowledge by a scale and shape parameter. Using a feedback procedure, experts can accept the representation of their beliefs or adjust their input. We propose a Five-Step Method which consists of (1 Eliciting the location parameter using the trial roulette method. (2 Provide feedback on the location parameter and ask for confirmation or adjustment. (3 Elicit the scale and shape parameter. (4 Provide feedback on the scale and shape parameter and ask for confirmation or adjustment. (5 Use the elicited and calibrated probability distribution in a statistical analysis and update it with data or to compute a prior-data conflict within a Bayesian framework. User feasibility and internal validity for the Five-Step Method are investigated using three elicitation studies.

A Proposal of New Spherical Particle Modeling Method Based on Stochastic Sampling of Particle Locations in Monte Carlo Simulation

Energy Technology Data Exchange (ETDEWEB)

Kim, Song Hyun; Kim, Do Hyun; Kim, Jong Kyung [Hanyang Univ., Seoul (Korea, Republic of); Noh, Jea Man [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

To the high computational efficiency and user convenience, the implicit method had received attention; however, it is noted that the implicit method in the previous studies has low accuracy at high packing fraction. In this study, a new implicit method, which can be used at any packing fraction with high accuracy, is proposed. In this study, the implicit modeling method in the spherical particle distributed medium for using the MC simulation is proposed. A new concept in the spherical particle sampling was developed to solve the problems in the previous implicit methods. The sampling method was verified by simulating the sampling method in the infinite and finite medium. The results show that the particle implicit modeling with the proposed method was accurately performed in all packing fraction boundaries. It is expected that the proposed method can be efficiently utilized for the spherical particle distributed mediums, which are the fusion reactor blanket, VHTR reactors, and shielding analysis.

A proposed safety assurance method and its application to the fusion experimental reactor

International Nuclear Information System (INIS)

Okazaki, T.; Seki, Y.; Inabe, T.; Aoki, I.

1995-01-01

Importance categorization and hazard identification methods have been proposed for a fusion experimental reactor. A parameter, the system index, is introduced in the categorization method. The relative importance of systems with safety functions can be classified by the largeness of the system index and whether or not the system acts as a boundary for radioactive materials. This categorization can be used as the basic principle in determining structure design assessment, seismic design criteria etc. For the hazard identification the system time energy matrix is proposed, where the time and spatial distributions of hazard energies are used. This approach is formulated more systematically than an ad-hoc identification of hazard events and it is useful to select design basis events which are employed in the assessment of safety designs. (orig.)

A Proposal on the Advanced Sampling Based Sensitivity and Uncertainty Analysis Method for the Eigenvalue Uncertainty Analysis

International Nuclear Information System (INIS)

Kim, Song Hyun; Song, Myung Sub; Shin, Chang Ho; Noh, Jae Man

2014-01-01

In using the perturbation theory, the uncertainty of the response can be estimated by a single transport simulation, and therefore it requires small computational load. However, it has a disadvantage that the computation methodology must be modified whenever estimating different response type such as multiplication factor, flux, or power distribution. Hence, it is suitable for analyzing few responses with lots of perturbed parameters. Statistical approach is a sampling based method which uses randomly sampled cross sections from covariance data for analyzing the uncertainty of the response. XSUSA is a code based on the statistical approach. The cross sections are only modified with the sampling based method; thus, general transport codes can be directly utilized for the S/U analysis without any code modifications. However, to calculate the uncertainty distribution from the result, code simulation should be enough repeated with randomly sampled cross sections. Therefore, this inefficiency is known as a disadvantage of the stochastic method. In this study, an advanced sampling method of the cross sections is proposed and verified to increase the estimation efficiency of the sampling based method. In this study, to increase the estimation efficiency of the sampling based S/U method, an advanced sampling and estimation method was proposed. The main feature of the proposed method is that the cross section averaged from each single sampled cross section is used. For the use of the proposed method, the validation was performed using the perturbation theory

Monju: Current status and proposed improvements

International Nuclear Information System (INIS)

Nagata, Takashi

2001-01-01

Activities since the Monju reactor accident are described. They include investigation of sodium leak, namely cause of thermocouple well failure and damage caused by sodium combustion. This accident did not affect the safety of the reactor or the integrity of the buildings and structures. Improvements have been proposed to overcome the problems highlighted by the comprehensive safety review of Monju. Improvements of communication are discussed, including incident reporting, public information, corporate culture. The proposed countermeasures against sodium leakage are described in detail. They are as follows: prevention of sodium leakage, early detection of sodium leakage, reduction of sodium spilling and prevention of re-ignition, suppression of moisture release from concrete structures. Replacement of thermocouple wells is proposed, as well as methods of preventing flow induced vibration

An assessment of the long term suitability of present and proposed methods for the management of uranium mill tailings

International Nuclear Information System (INIS)

1979-07-01

Proposals for safe, long-term containment of conventional tailings include 1) storage under water, 2) storage in active, abandoned or specially created underground mines and, 3) storage in open pits, with subsequent flooding or covering with overburden. The underwater proposal can meet most of the requirements of long term containment; however, extensive study of existing tailings deposits in deep water locations will be needed. Underground mines cannot provide sufficient storage capacity, since the tailings bulk during mill operation can occupy twice the volume of the original ore. It is possible to reduce the hazard by reducing the radium and thorium content of the tailings. Proposals for such an undertaking include ore beneficiation with rejection of the relatively innocuous fraction, radium-thorium removal in the mill, and significant changes in both ore processing and treatment of tailings. It is concluded that surface-stored tailings are vulnerable over the long term to dispersion by leaching and water erosion, and that access to a tailings site cannot be prevented, while only a major climatic or seismic event could disturb tailings stored in suitable underwater or underground mine sites. The criteria for determining suitability for each method, however, will need to be identified, tested, and accepted through the normal process of modeling, pilot plant evaluation, monitoring and evaluation. (author)

Second-principles method for materials simulations including electron and lattice degrees of freedom

Science.gov (United States)

García-Fernández, Pablo; Wojdeł, Jacek C.; Íñiguez, Jorge; Junquera, Javier

2016-05-01

We present a first-principles-based (second-principles) scheme that permits large-scale materials simulations including both atomic and electronic degrees of freedom on the same footing. The method is based on a predictive quantum-mechanical theory—e.g., density functional theory—and its accuracy can be systematically improved at a very modest computational cost. Our approach is based on dividing the electron density of the system into a reference part—typically corresponding to the system's neutral, geometry-dependent ground state—and a deformation part—defined as the difference between the actual and reference densities. We then take advantage of the fact that the bulk part of the system's energy depends on the reference density alone; this part can be efficiently and accurately described by a force field, thus avoiding explicit consideration of the electrons. Then, the effects associated to the difference density can be treated perturbatively with good precision by working in a suitably chosen Wannier function basis. Further, the electronic model can be restricted to the bands of interest. All these features combined yield a very flexible and computationally very efficient scheme. Here we present the basic formulation of this approach, as well as a practical strategy to compute model parameters for realistic materials. We illustrate the accuracy and scope of the proposed method with two case studies, namely, the relative stability of various spin arrangements in NiO (featuring complex magnetic interactions in a strongly-correlated oxide) and the formation of a two-dimensional electron gas at the interface between band insulators LaAlO3 and SrTiO3 (featuring subtle electron-lattice couplings and screening effects). We conclude by discussing ways to overcome the limitations of the present approach (most notably, the assumption of a fixed bonding topology), as well as its many envisioned possibilities and future extensions.

Test Methods for Evaluating Solid Waste, Physical/Chemical Methods. First Update. (3rd edition)

International Nuclear Information System (INIS)

Friedman; Sellers.

1988-01-01

The proposed Update is for Test Methods for Evaluating Solid Waste, Physical/Chemical Methods, SW-846, Third Edition. Attached to the report is a list of methods included in the proposed update indicating whether the method is a new method, a partially revised method, or a totally revised method. Do not discard or replace any of the current pages in the SW-846 manual until the proposed update I package is promulgated. Until promulgation of the update package, the methods in the update package are not officially part of the SW-846 manual and thus do not carry the status of EPA-approved methods. In addition to the proposed Update, six finalized methods are included for immediate inclusion into the Third Edition of SW-846. Four methods, originally proposed October 1, 1984, will be finalized in a soon to be released rulemaking. They are, however, being submitted to subscribers for the first time in the update. These methods are 7211, 7381, 7461, and 7951. Two other methods were finalized in the 2nd Edition of SW-846. They were inadvertantly omitted from the 3rd Edition and are not being proposed as new. These methods are 7081 and 7761

Proposal and Implementation of a Robust Sensing Method for DVB-T Signal

Science.gov (United States)

Song, Chunyi; Rahman, Mohammad Azizur; Harada, Hiroshi

This paper proposes a sensing method for TV signals of DVB-T standard to realize effective TV White Space (TVWS) Communication. In the TVWS technology trial organized by the Infocomm Development Authority (iDA) of Singapore, with regard to the sensing level and sensing time, detecting DVB-T signal at the level of -120dBm over an 8MHz channel with a sensing time below 1 second is required. To fulfill such a strict sensing requirement, we propose a smart sensing method which combines feature detection and energy detection (CFED), and is also characterized by using dynamic threshold selection (DTS) based on a threshold table to improve sensing robustness to noise uncertainty. The DTS based CFED (DTS-CFED) is evaluated by computer simulations and is also implemented into a hardware sensing prototype. The results show that the DTS-CFED achieves a detection probability above 0.9 for a target false alarm probability of 0.1 for DVB-T signals at the level of -120dBm over an 8MHz channel with the sensing time equals to 0.1 second.

25 CFR 900.125 - What shall a construction contract proposal contain?

Science.gov (United States)

2010-04-01

... organization shall also include in its construction contract proposal the following: (1) In the case of a... accept the tribally proposed standards; and (2) In the case of a contract for construction activities... methods (including national, regional, state, or tribal building codes or construction industry standards...

Proposal and Evaluation of Management Method for College Mechatronics Education Applying the Project Management

Science.gov (United States)

Ando, Yoshinobu; Eguchi, Yuya; Mizukawa, Makoto

In this research, we proposed and evaluated a management method of college mechatronics education. We applied the project management to college mechatronics education. We practiced our management method to the seminar “Microcomputer Seminar” for 3rd grade students who belong to Department of Electrical Engineering, Shibaura Institute of Technology. We succeeded in management of Microcomputer Seminar in 2006. We obtained the good evaluation for our management method by means of questionnaire.

A Proposal of Estimation Methodology to Improve Calculation Efficiency of Sampling-based Method in Nuclear Data Sensitivity and Uncertainty Analysis

International Nuclear Information System (INIS)

Song, Myung Sub; Kim, Song Hyun; Kim, Jong Kyung; Noh, Jae Man

2014-01-01

The uncertainty with the sampling-based method is evaluated by repeating transport calculations with a number of cross section data sampled from the covariance uncertainty data. In the transport calculation with the sampling-based method, the transport equation is not modified; therefore, all uncertainties of the responses such as k eff , reaction rates, flux and power distribution can be directly obtained all at one time without code modification. However, a major drawback with the sampling-based method is that it requires expensive computational load for statistically reliable results (inside confidence level 0.95) in the uncertainty analysis. The purpose of this study is to develop a method for improving the computational efficiency and obtaining highly reliable uncertainty result in using the sampling-based method with Monte Carlo simulation. The proposed method is a method to reduce the convergence time of the response uncertainty by using the multiple sets of sampled group cross sections in a single Monte Carlo simulation. The proposed method was verified by estimating GODIVA benchmark problem and the results were compared with that of conventional sampling-based method. In this study, sampling-based method based on central limit theorem is proposed to improve calculation efficiency by reducing the number of repetitive Monte Carlo transport calculation required to obtain reliable uncertainty analysis results. Each set of sampled group cross sections is assigned to each active cycle group in a single Monte Carlo simulation. The criticality uncertainty for the GODIVA problem is evaluated by the proposed and previous method. The results show that the proposed sampling-based method can efficiently decrease the number of Monte Carlo simulation required for evaluate uncertainty of k eff . It is expected that the proposed method will improve computational efficiency of uncertainty analysis with sampling-based method

Proposal for outline of training and evaluation method for non-technical skills

International Nuclear Information System (INIS)

Nagasaka, Akihiko; Shibue, Hisao

2015-01-01

The purpose of this study is to systematize measures for improvement of emergency response capability focused on non-technical skills. As the results of investigation of some emergency training in nuclear power plant and referring to CRM training, following two issues were picked up. 1) Lack of practical training method for improvement of non-technical skills. 2) Lack of evaluation method of non-technical skills. Then, based on these 7 non-technical skills 'situational awareness' 'decision making' 'communication' 'teamworking' 'leadership' 'managing stress' 'coping with fatigue' are promotion factors to improve emergency response capability, we propose practical training method for each non-technical skill. Also we give example of behavioral markers as evaluation factor, and indicate approaches to introduce the evaluation method of non-technical skills. (author)

Systems and Methods for Fabricating Structures Including Metallic Glass-Based Materials Using Low Pressure Casting

Science.gov (United States)

Hofmann, Douglas C. (Inventor); Kennett, Andrew (Inventor)

2018-01-01

Systems and methods to fabricate objects including metallic glass-based materials using low-pressure casting techniques are described. In one embodiment, a method of fabricating an object that includes a metallic glass-based material includes: introducing molten alloy into a mold cavity defined by a mold using a low enough pressure such that the molten alloy does not conform to features of the mold cavity that are smaller than 100 microns; and cooling the molten alloy such that it solidifies, the solid including a metallic glass-based material.

48 CFR 815.404-1 - Proposal analysis techniques.

Science.gov (United States)

2010-10-01

... CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Contract Pricing 815.404-1 Proposal analysis... necessary for initial and revised pricing of all negotiated prime contracts, including subcontract pricing...

Solar cells, structures including organometallic halide perovskite monocrystalline films, and methods of preparation thereof

KAUST Repository

Bakr, Osman; Peng, Wei; Wang, Lingfei

2017-01-01

Embodiments of the present disclosure provide for solar cells including an organometallic halide perovskite monocrystalline film (see fig. 1.1B), other devices including the organometallic halide perovskite monocrystalline film, methods of making

Visual assessment of BIPV retrofit design proposals for selected historical buildings using the saliency map method

Directory of Open Access Journals (Sweden)

Ran Xu

2015-06-01

Full Text Available With the increasing awareness of energy efficiency, many old buildings have to undergo a massive facade energy retrofit. How to predict the visual impact which solar installations on the aesthetic cultural value of these buildings has been a heated debate in Switzerland (and throughout the world. The usual evaluation method to describe the visual impact of BIPV is based on semantic and qualitative descriptors, and strongly dependent on personal preferences. The evaluation scale is therefore relative, flexible and imprecise. This paper proposes a new method to accurately measure the visual impact which BIPV installations have on a historical building by using the saliency map method. By imitating working principles of the human eye, it is measured how much the BIPV design proposals differ from the original building facade in the aspect of attracting human visual attention. The result is directly presented in a quantitative manner, and can be used to compare the fitness of different BIPV design proposals. The measuring process is numeric, objective and more precise.  

Electrode assemblies, plasma apparatuses and systems including electrode assemblies, and methods for generating plasma

Science.gov (United States)

Kong, Peter C; Grandy, Jon D; Detering, Brent A; Zuck, Larry D

2013-09-17

Electrode assemblies for plasma reactors include a structure or device for constraining an arc endpoint to a selected area or region on an electrode. In some embodiments, the structure or device may comprise one or more insulating members covering a portion of an electrode. In additional embodiments, the structure or device may provide a magnetic field configured to control a location of an arc endpoint on the electrode. Plasma generating modules, apparatus, and systems include such electrode assemblies. Methods for generating a plasma include covering at least a portion of a surface of an electrode with an electrically insulating member to constrain a location of an arc endpoint on the electrode. Additional methods for generating a plasma include generating a magnetic field to constrain a location of an arc endpoint on an electrode.

A proposed assessment method for image of regional educational institutions

Directory of Open Access Journals (Sweden)

Kataeva Natalya

2017-01-01

Full Text Available Market of educational services in the current Russian economic conditions is a complex of a huge variety of educational institutions. Market of educational services is already experiencing a significant influence of the demographic situation in Russia. This means that higher education institutions are forced to fight in a tough competition for high school students. Increased competition in the educational market forces universities to find new methods of non-price competition in attraction of potential students and throughout own educational and economic activities. Commercialization of education places universities in a single plane with commercial companies who study a positive perception of the image and reputation as a competitive advantage, which is quite acceptable for use in strategic and current activities of higher education institutions to ensure the competitiveness of educational services and educational institution in whole. Nevertheless, due to lack of evidence-based proposals in this area there is a need for scientific research in terms of justification of organizational and methodological aspects of image use as a factor in the competitiveness of the higher education institution. Theoretically and practically there are different methods and ways of evaluating the company’s image. The article provides a comparative assessment of the existing valuation methods of corporate image and the author’s method of estimating the image of higher education institutions based on the key influencing factors. The method has been tested on the Vyatka State Agricultural Academy (Russia. The results also indicate the strengths and weaknesses of the institution, highlights ways of improving, and adjusts the efforts for image improvement.

A novel method of including Landau level mixing in numerical studies of the quantum Hall effect

International Nuclear Information System (INIS)

Wooten, Rachel; Quinn, John; Macek, Joseph

2013-01-01

Landau level mixing should influence the quantum Hall effect for all except the strongest applied magnetic fields. We propose a simple method for examining the effects of Landau level mixing by incorporating multiple Landau levels into the Haldane pseudopotentials through exact numerical diagonalization. Some of the resulting pseudopotentials for the lowest and first excited Landau levels will be presented

Proposed waste form performance criteria and testing methods for low-level mixed waste

International Nuclear Information System (INIS)

Franz, E.M.; Fuhrmann, M.; Bowerman, B.

1995-01-01

Proposed waste form performance criteria and testing methods were developed as guidance in judging the suitability of solidified waste as a physico-chemical barrier to releases of radionuclides and RCRA regulated hazardous components. The criteria follow from the assumption that release of contaminants by leaching is the single most important property for judging the effectiveness of a waste form. A two-tier regimen is proposed. The first tier consists of a leach test designed to determine the net, forward leach rate of the solidified waste and a leach test required by the Environmental Protection Agency (EPA). The second tier of tests is to determine if a set of stresses (i.e., radiation, freeze-thaw, wet-dry cycling) on the waste form adversely impacts its ability to retain contaminants and remain physically intact. In the absence of site-specific performance assessments (PA), two generic modeling exercises are described which were used to calculate proposed acceptable leachates

A framework for employing femtosatellites in planetary science missions, including a proposed mission concept for Titan

Science.gov (United States)

Perez, Tracie Renea Conn

Over the past 15 years, there has been a growing interest in femtosatellites, a class of tiny satellites having mass less than 100 grams. Research groups from Peru, Spain, England, Canada, and the United States have proposed femtosat designs and novel mission concepts for them. In fact, Peru made history in 2013 by releasing the first - and still only - femtosat tracked from LEO. However, femtosatellite applications in interplanetary missions have yet to be explored in detail. An interesting operations concept would be for a space probe to release numerous femtosatellites into orbit around a planetary object of interest, thereby augmenting the overall data collection capability of the mission. A planetary probe releasing hundreds of femtosats could complete an in-situ, simultaneous 3D mapping of a physical property of interest, achieving scientific investigations not possible for one probe operating alone. To study the technical challenges associated with such a mission, a conceptual mission design is proposed where femtosats are deployed from a host satellite orbiting Titan. The conceptual mission objective is presented: to study Titan's dynamic atmosphere. Then, the design challenges are addressed in turn. First, any science payload measurements that the femtosats provide are only useful if their corresponding locations can be determined. Specifically, what's required is a method of position determination for femtosatellites operating beyond Medium Earth Orbit and therefore beyond the help of GPS. A technique is presented which applies Kalman filter techniques to Doppler shift measurements, allowing for orbit determination of the femtosats. Several case studies are presented demonstrating the usefulness of this approach. Second, due to the inherit power and computational limitations in a femtosatellite design, establishing a radio link between each chipsat and the mothersat will be difficult. To provide a mathematical gain, a particular form of forward error

Creep-fatigue evaluation method for weld joint of Mod.9Cr-1Mo steel Part II: Plate bending test and proposal of a simplified evaluation method

Energy Technology Data Exchange (ETDEWEB)

Ando, Masanori, E-mail: ando.masanori@jaea.go.jp; Takaya, Shigeru, E-mail: takaya.shigeru@jaea.go.jp

2016-12-15

Highlights: • Creep-fatigue evaluation method for weld joint of Mod.9Cr-1Mo steel is proposed. • A simplified evaluation method is also proposed for the codification. • Both proposed evaluation method was validated by the plate bending test. • For codification, the local stress and strain behavior was analyzed. - Abstract: In the present study, to develop an evaluation procedure and design rules for Mod.9Cr-1Mo steel weld joints, a method for evaluating the creep-fatigue life of Mod.9Cr-1Mo steel weld joints was proposed based on finite element analysis (FEA) and a series of cyclic plate bending tests of longitudinal and horizontal seamed plates. The strain concentration and redistribution behaviors were evaluated and the failure cycles were estimated using FEA by considering the test conditions and metallurgical discontinuities in the weld joints. Inelastic FEA models consisting of the base metal, heat-affected zone and weld metal were employed to estimate the elastic follow-up behavior caused by the metallurgical discontinuities. The elastic follow-up factors determined by comparing the elastic and inelastic FEA results were determined to be less than 1.5. Based on the estimated elastic follow-up factors obtained via inelastic FEA, a simplified technique using elastic FEA was proposed for evaluating the creep-fatigue life in Mod.9Cr-1Mo steel weld joints. The creep-fatigue life obtained using the plate bending test was compared to those estimated from the results of inelastic FEA and by a simplified evaluation method.

Creep-fatigue evaluation method for weld joint of Mod.9Cr-1Mo steel Part II: Plate bending test and proposal of a simplified evaluation method

International Nuclear Information System (INIS)

Ando, Masanori; Takaya, Shigeru

2016-01-01

Highlights: • Creep-fatigue evaluation method for weld joint of Mod.9Cr-1Mo steel is proposed. • A simplified evaluation method is also proposed for the codification. • Both proposed evaluation method was validated by the plate bending test. • For codification, the local stress and strain behavior was analyzed. - Abstract: In the present study, to develop an evaluation procedure and design rules for Mod.9Cr-1Mo steel weld joints, a method for evaluating the creep-fatigue life of Mod.9Cr-1Mo steel weld joints was proposed based on finite element analysis (FEA) and a series of cyclic plate bending tests of longitudinal and horizontal seamed plates. The strain concentration and redistribution behaviors were evaluated and the failure cycles were estimated using FEA by considering the test conditions and metallurgical discontinuities in the weld joints. Inelastic FEA models consisting of the base metal, heat-affected zone and weld metal were employed to estimate the elastic follow-up behavior caused by the metallurgical discontinuities. The elastic follow-up factors determined by comparing the elastic and inelastic FEA results were determined to be less than 1.5. Based on the estimated elastic follow-up factors obtained via inelastic FEA, a simplified technique using elastic FEA was proposed for evaluating the creep-fatigue life in Mod.9Cr-1Mo steel weld joints. The creep-fatigue life obtained using the plate bending test was compared to those estimated from the results of inelastic FEA and by a simplified evaluation method.

Solar cells, structures including organometallic halide perovskite monocrystalline films, and methods of preparation thereof

KAUST Repository

Bakr, Osman M.

2017-03-02

Embodiments of the present disclosure provide for solar cells including an organometallic halide perovskite monocrystalline film (see fig. 1.1B), other devices including the organometallic halide perovskite monocrystalline film, methods of making organometallic halide perovskite monocrystalline film, and the like.

Proposal of evaluation method of tsunami wave pressure using 2D depth-integrated flow simulation

International Nuclear Information System (INIS)

Arimitsu, Tsuyoshi; Ooe, Kazuya; Kawasaki, Koji

2012-01-01

To design and construct land structures resistive to tsunami force, it is most essential to evaluate tsunami pressure quantitatively. The existing hydrostatic formula, in general, tended to underestimate tsunami wave pressure under the condition of inundation flow with large Froude number. Estimation method of tsunami pressure acting on a land structure was proposed using inundation depth and horizontal velocity at the front of the structure, which were calculated employing a 2D depth-integrated flow model based on the unstructured grid system. The comparison between the numerical and experimental results revealed that the proposed method could reasonably reproduce the vertical distribution of the maximum tsunami pressure as well as the time variation of the tsunami pressure exerting on the structure. (author)

Earthquake analysis of structures including structure-soil interaction by a substructure method

International Nuclear Information System (INIS)

Chopra, A.K.; Guttierrez, J.A.

1977-01-01

A general substructure method for analysis of response of nuclear power plant structures to earthquake ground motion, including the effects of structure-soil interaction, is summarized. The method is applicable to complex structures idealized as finite element systems and the soil region treated as either a continuum, for example as a viscoelastic halfspace, or idealized as a finite element system. The halfspace idealization permits reliable analysis for sites where essentially similar soils extend to large depths and there is no rigid boundary such as soil-rock interface. For sites where layers of soft soil are underlain by rock at shallow depth, finite element idealization of the soil region is appropriate; in this case, the direct and substructure methods would lead to equivalent results but the latter provides the better alternative. Treating the free field motion directly as the earthquake input in the substructure eliminates the deconvolution calculations and the related assumption-regarding type and direction of earthquake waves-required in the direct method. (Auth.)

77 FR 24684 - Proposed Information Collection; Comment Request; 2013-2015 American Community Survey Methods...

Science.gov (United States)

2012-04-25

... proposed content changes. Thus, we need to test an alternative questionnaire design to accommodate additional content on the ACS mail questionnaire. In the 2013 ACS Questionnaire Design Test, we will study... in Puerto Rico. II. Method of Collection Questionnaire Design Test--Data collection for this test...

Gene set analysis: limitations in popular existing methods and proposed improvements.

Science.gov (United States)

Mishra, Pashupati; Törönen, Petri; Leino, Yrjö; Holm, Liisa

2014-10-01

Gene set analysis is the analysis of a set of genes that collectively contribute to a biological process. Most popular gene set analysis methods are based on empirical P-value that requires large number of permutations. Despite numerous gene set analysis methods developed in the past decade, the most popular methods still suffer from serious limitations. We present a gene set analysis method (mGSZ) based on Gene Set Z-scoring function (GSZ) and asymptotic P-values. Asymptotic P-value calculation requires fewer permutations, and thus speeds up the gene set analysis process. We compare the GSZ-scoring function with seven popular gene set scoring functions and show that GSZ stands out as the best scoring function. In addition, we show improved performance of the GSA method when the max-mean statistics is replaced by the GSZ scoring function. We demonstrate the importance of both gene and sample permutations by showing the consequences in the absence of one or the other. A comparison of asymptotic and empirical methods of P-value estimation demonstrates a clear advantage of asymptotic P-value over empirical P-value. We show that mGSZ outperforms the state-of-the-art methods based on two different evaluations. We compared mGSZ results with permutation and rotation tests and show that rotation does not improve our asymptotic P-values. We also propose well-known asymptotic distribution models for three of the compared methods. mGSZ is available as R package from cran.r-project.org. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Proposals for Iterated Hash Functions

DEFF Research Database (Denmark)

Knudsen, Lars Ramkilde; Thomsen, Søren Steffen

2008-01-01

The past few years have seen an increase in the number of attacks on cryptographic hash functions. These include attacks directed at specific hash functions, and generic attacks on the typical method of constructing hash functions. In this paper we discuss possible methods for protecting against...... some generic attacks. We also give a concrete proposal for a new hash function construction, given a secure compression function which, unlike in typical existing constructions, is not required to be resistant to all types of collisions. Finally, we show how members of the SHA-family can be turned...

Proposals for iterated hash functions

DEFF Research Database (Denmark)

Knudsen, Lars Ramkilde; Thomsen, Søren Steffen

2006-01-01

The past few years have seen an increase in the number of attacks on cryptographic hash functions. These include attacks directed at specific hash functions, and generic attacks on the typical method of constructing hash functions. In this paper we discuss possible methods for protecting against...... some generic attacks. We also give a concrete proposal for a new hash function construction, given a secure compression function which, unlike in typical existing constructions, is not required to be resistant to all types of collisions. Finally, we show how members of the SHA-family can be turned...

A Method for Proposing Valued-Adding Attributes in Customized Housing

Directory of Open Access Journals (Sweden)

Cynthia S. Hentschke

2014-12-01

Full Text Available In most emerging economies, there has been many incentives and high availability of funding for low-cost housing projects. This has encouraged product standardization and the application of mass production ideas, based on the assumption that this is the most effective strategy for reducing costs. However, the delivery of highly standardized housing units to customers with different needs, without considering their lifestyle and perception of value, often results in inadequate products. Mass customization has been pointed out as an effective strategy to improve value generation in low-cost housing projects, and to avoid waste caused by renovations done in dwellings soon after occupancy. However, one of the main challenges for the implementation of mass customization is the definition of a set of relevant options based on users’ perceived value. The aim of this paper is to propose a method for defining value adding attributes in customized housing projects, which can support decision-making in product development. The means-end chain theory was used as theoretical framework to connect product attributes and costumers’ values, through the application of the laddering technique. The method was tested in two house-building projects delivered by a company from Brazil. The main contribution of this method is to indicate the customization units that are most important for users along with the explanation of why those units are the most relevant ones.

Proposal and field practice of a 'hiyarihatto' activity method for promotion of statements of participants for nuclear power plant organization

International Nuclear Information System (INIS)

Aoyagi, Saizo; Fujino, Hidenori; Ishii, Hirotake; Shimoda, Hiroshi; Sakuda, Hiroshi; Yoshikawa, Hidekazu; Sugiman, Toshio

2011-01-01

In a 'hiyarihatto' activity, workers report and discuss incident cases related to their work. Such an activity is particularly effective for cultivating participants' attitudes about safety. Nevertheless, a conventional face-to-face hiyarihatto activity includes features that are inappropriate for conduct in a nuclear power plant organization. For example, workers at nuclear power plants are geographically distributed and busy. Therefore, they have great difficulty in participating in a face-to-face hiyarihatto activity. Furthermore, workers' hesitation in discussing problems inhibits the continuation of their active participation. This study is conducted to propose a hiyarihatto activity with an asynchronous and distributed computer-mediated communication (CMC) for a nuclear power plant organization, with the demonstration of its effectiveness through field practice. The proposed method also involves the introduction of special participants who follow action guidelines for the promotion of the continuation of the activity. The method was used in an actual nuclear power plant organization. Results showed that the method is effective under some conditions, such as during periods without facility inspection. Special participants promoted the activity in some cases. Moreover, other factors affecting the activity and some improvements were identified. (author)

Review of Dercum’s disease and proposal of diagnostic criteria, diagnostic methods, classification and management

Directory of Open Access Journals (Sweden)

Hansson Emma

2012-04-01

Full Text Available Abstract Definition and clinical picture We propose the minimal definition of Dercum’s disease to be generalised overweight or obesity in combination with painful adipose tissue. The associated symptoms in Dercum’s disease include fatty deposits, easy bruisability, sleep disturbances, impaired memory, depression, difficulty concentrating, anxiety, rapid heartbeat, shortness of breath, diabetes, bloating, constipation, fatigue, weakness and joint aches. Classification We suggest that Dercum’s disease is classified into: I. Generalised diffuse form A form with diffusely widespread painful adipose tissue without clear lipomas, II. Generalised nodular form - a form with general pain in adipose tissue and intense pain in and around multiple lipomas, and III. Localised nodular form - a form with pain in and around multiple lipomas IV. Juxtaarticular form - a form with solitary deposits of excess fat for example at the medial aspect of the knee. Epidemiology Dercum’s disease most commonly appears between the ages of 35 and 50 years and is five to thirty times more common in women than in men. The prevalence of Dercum’s disease has not yet been exactly established. Aetiology Proposed, but unconfirmed aetiologies include: nervous system dysfunction, mechanical pressure on nerves, adipose tissue dysfunction and trauma. Diagnosis and diagnostic methods Diagnosis is based on clinical criteria and should be made by systematic physical examination and thorough exclusion of differential diagnoses. Advisably, the diagnosis should be made by a physician with a broad experience of patients with painful conditions and knowledge of family medicine, internal medicine or pain management. The diagnosis should only be made when the differential diagnoses have been excluded. Differential diagnosis Differential diagnoses include: fibromyalgia, lipoedema, panniculitis, endocrine disorders, primary psychiatric disorders, multiple symmetric lipomatosis, familial

New Multigrid Method Including Elimination Algolithm Based on High-Order Vector Finite Elements in Three Dimensional Magnetostatic Field Analysis

Science.gov (United States)

Hano, Mitsuo; Hotta, Masashi

A new multigrid method based on high-order vector finite elements is proposed in this paper. Low level discretizations in this method are obtained by using low-order vector finite elements for the same mesh. Gauss-Seidel method is used as a smoother, and a linear equation of lowest level is solved by ICCG method. But it is often found that multigrid solutions do not converge into ICCG solutions. An elimination algolithm of constant term using a null space of the coefficient matrix is also described. In three dimensional magnetostatic field analysis, convergence time and number of iteration of this multigrid method are discussed with the convectional ICCG method.

Proposed integrated hazardous waste disposal facility. Public environmental review

International Nuclear Information System (INIS)

1998-05-01

This Public Environmental Report describes a proposal by the Health Department of Western Australia to establish a disposal facility for certain hazardous wastes and seeks comments from governments agencies and the public that will assist the EPA to make its recommendations to. The facility would only be used for wastes generated in Western Australia.The proposal specifically includes: a high temperature incinerator for the disposal of organo-chlorines (including agricultural chemicals and PCBs), and other intractable wastes for which this is the optimum disposal method; an area for the burial (after any appropriate conditioning) of low level radioactive intractable wastes arising from the processing of mineral sands (including monazite, ilmenite and zircon) and phosphate rock. Detailed information is presented on those wastes which are currently identified as requiring disposal at the facility.The proposed facility will also be suitable for the disposal of other intractable wastes including radioactive wastes (from industry, medicine and research) and other solid intractable wastes of a chemical nature including spent catalysts etc. Proposals to dispose of these other wastes at this facility in the future will be referred to the Environmental Protection Authority for separate assessment

Verbal Auditory Cueing of Improvisational Dance: A Proposed Method for Training Agency in Parkinson’s Disease

Science.gov (United States)

Batson, Glenna; Hugenschmidt, Christina E.; Soriano, Christina T.

2016-01-01

Dance is a non-pharmacological intervention that helps maintain functional independence and quality of life in people with Parkinson’s disease (PPD). Results from controlled studies on group-delivered dance for people with mild-to-moderate stage Parkinson’s have shown statistically and clinically significant improvements in gait, balance, and psychosocial factors. Tested interventions include non-partnered dance forms (ballet and modern dance) and partnered (tango). In all of these dance forms, specific movement patterns initially are learned through repetition and performed in time-to-music. Once the basic steps are mastered, students may be encouraged to improvise on the learned steps as they perform them in rhythm with the music. Here, we summarize a method of teaching improvisational dance that advances previous reported benefits of dance for people with Parkinson’s disease (PD). The method relies primarily on improvisational verbal auditory cueing with less emphasis on directed movement instruction. This method builds on the idea that daily living requires flexible, adaptive responses to real-life challenges. In PD, movement disorders not only limit mobility but also impair spontaneity of thought and action. Dance improvisation demands open and immediate interpretation of verbally delivered movement cues, potentially fostering the formation of spontaneous movement strategies. Here, we present an introduction to a proposed method, detailing its methodological specifics, and pointing to future directions. The viewpoint advances an embodied cognitive approach that has eco-validity in helping PPD meet the changing demands of daily living. PMID:26925029

Comparison among four proposed direct blood culture microbial identification methods using MALDI-TOF MS.

Science.gov (United States)

Bazzi, Ali M; Rabaan, Ali A; El Edaily, Zeyad; John, Susan; Fawarah, Mahmoud M; Al-Tawfiq, Jaffar A

Matrix-assisted laser desorption-ionization time-of-flight (MALDI-TOF) mass spectrometry facilitates rapid and accurate identification of pathogens, which is critical for sepsis patients. In this study, we assessed the accuracy in identification of both Gram-negative and Gram-positive bacteria, except for Streptococcus viridans, using four rapid blood culture methods with Vitek MALDI-TOF-MS. We compared our proposed lysis centrifugation followed by washing and 30% acetic acid treatment method (method 2) with two other lysis centrifugation methods (washing and 30% formic acid treatment (method 1); 100% ethanol treatment (method 3)), and picking colonies from 90 to 180min subculture plates (method 4). Methods 1 and 2 identified all organisms down to species level with 100% accuracy, except for Streptococcus viridans, Streptococcus pyogenes, Enterobacter cloacae and Proteus vulgaris. The latter two were identified to genus level with 100% accuracy. Each method exhibited excellent accuracy and precision in terms of identification to genus level with certain limitations. Copyright © 2016 King Saud Bin Abdulaziz University for Health Sciences. Published by Elsevier Ltd. All rights reserved.

Comparison among four proposed direct blood culture microbial identification methods using MALDI-TOF MS

Directory of Open Access Journals (Sweden)

Ali M. Bazzi

2017-05-01

Full Text Available Summary: Matrix-assisted laser desorption-ionization time-of-flight (MALDI-TOF mass spectrometry facilitates rapid and accurate identification of pathogens, which is critical for sepsis patients.In this study, we assessed the accuracy in identification of both Gram-negative and Gram-positive bacteria, except for Streptococcus viridans, using four rapid blood culture methods with Vitek MALDI-TOF-MS. We compared our proposed lysis centrifugation followed by washing and 30% acetic acid treatment method (method 2 with two other lysis centrifugation methods (washing and 30% formic acid treatment (method 1; 100% ethanol treatment (method 3, and picking colonies from 90 to 180 min subculture plates (method 4. Methods 1 and 2 identified all organisms down to species level with 100% accuracy, except for Streptococcus viridans, Streptococcus pyogenes, Enterobacter cloacae and Proteus vulgaris. The latter two were identified to genus level with 100% accuracy. Each method exhibited excellent accuracy and precision in terms of identification to genus level with certain limitations. Keywords: MALDI-TOF, Gram-negative, Gram-positive, Sepsis, Blood culture

European experiences of the proposed ASTM test method for crack arrest toughness of ferritic materials

International Nuclear Information System (INIS)

Jutla, T.; Lidbury, D.P.G.; Ziebs, J.; Zimmermann, C.

1986-01-01

The proposed ASTM test method for measuring the crack arrest toughness of ferritic materials using wedge-loaded, side-grooved, compact specimens was applied to three steels: A514 bridge steel, A588 bridge steel, and A533B pressure vessel steel. Five sets of results from different laboratories are discussed here. Notches were prepared by spark erosion, although root radii varied from ∝0.1-1.5 mm. Although fast fractures were successfully initiated, arrest did not occur in a significant number of cases. The results showed no obvious dependence of crack arrest toughness, K a , (determined by a static analysis) on crack initiation toughness, K 0 . It was found that K a decreases markedly with increasing crack jump distance. A limited amount of further work on smaller specimens of the A533B steel showed that lower K a values tended to be recorded. It is concluded that a number of points relating to the proposed test method and notch preparation are worthy of further consideration. It is pointed out that the proposed validity criteria may screen out lower bound data. Nevertheless, for present practical purposes, K a values may be regarded as useful in providing an estimate of arrest toughness - although not necessarily a conservative estimate. (orig./HP)

Earthquake analysis of structures including structure-soil interaction by a substructure method

International Nuclear Information System (INIS)

Chopra, A.K.; Guttierrez, J.A.

1977-01-01

A general substructure method for analysis of response of nuclear power plant structures to earthquake ground motion, including the effects of structure-soil interaction, is summarized. The method is applicable to complex structures idealized as finite element systems and the soil region treated as either a continuum, for example as a viscoelastic halfspace, or idealized as a finite element system. The halfspace idealization permits reliable analysis for sites where essentially similar soils extend to large depths and there is no rigid boundary such as soil-rock interface. For sites where layers of soft soil are underlain by rock at shallow depth, finite element idealization of the soil region is appropriate; in this case, the direct and substructure methods would lead to equivalent results but the latter provides the better alternative. Treating the free field motion directly as the earthquake input in the substructure method eliminates the deconvolution calculations and the related assumption -regarding type and direction of earthquake waves- required in the direct method. The substructure method is computationally efficient because the two substructures-the structure and the soil region- are analyzed separately; and, more important, it permits taking advantage of the important feature that response to earthquake ground motion is essentially contained in the lower few natural modes of vibration of the structure on fixed base. For sites where essentially similar soils extend to large depths and there is no obvious rigid boundary such as a soil-rock interface, numerical results for earthquake response of a nuclear reactor structure are presented to demonstrate that the commonly used finite element method may lead to unacceptable errors; but the substructure method leads to reliable results

A Proposal on the Quantitative Homogeneity Analysis Method of SEM Images for Material Inspections

Energy Technology Data Exchange (ETDEWEB)

Kim, Song Hyun; Kim, Jong Woo; Shin, Chang Ho [Hanyang University, Seoul (Korea, Republic of); Choi, Jung-Hoon; Cho, In-Hak; Park, Hwan Seo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

A scanning electron microscope (SEM) is a method to inspect the surface microstructure of materials. The SEM uses electron beams for imaging high magnifications of material surfaces; therefore, various chemical analyses can be performed from the SEM images. Therefore, it is widely used for the material inspection, chemical characteristic analysis, and biological analysis. For the nuclear criticality analysis field, it is an important parameter to check the homogeneity of the compound material for using it in the nuclear system. In our previous study, the SEM was tried to use for the homogeneity analysis of the materials. In this study, a quantitative homogeneity analysis method of SEM images is proposed for the material inspections. The method is based on the stochastic analysis method with the information of the grayscales of the SEM images.

A Proposal on the Quantitative Homogeneity Analysis Method of SEM Images for Material Inspections

International Nuclear Information System (INIS)

Kim, Song Hyun; Kim, Jong Woo; Shin, Chang Ho; Choi, Jung-Hoon; Cho, In-Hak; Park, Hwan Seo

2015-01-01

A scanning electron microscope (SEM) is a method to inspect the surface microstructure of materials. The SEM uses electron beams for imaging high magnifications of material surfaces; therefore, various chemical analyses can be performed from the SEM images. Therefore, it is widely used for the material inspection, chemical characteristic analysis, and biological analysis. For the nuclear criticality analysis field, it is an important parameter to check the homogeneity of the compound material for using it in the nuclear system. In our previous study, the SEM was tried to use for the homogeneity analysis of the materials. In this study, a quantitative homogeneity analysis method of SEM images is proposed for the material inspections. The method is based on the stochastic analysis method with the information of the grayscales of the SEM images

Refining borders of genome-rearrangements including repetitions

Directory of Open Access Journals (Sweden)

JA Arjona-Medina

2016-10-01

Full Text Available Abstract Background DNA rearrangement events have been widely studied in comparative genomic for many years. The importance of these events resides not only in the study about relatedness among different species, but also to determine the mechanisms behind evolution. Although there are many methods to identify genome-rearrangements (GR, the refinement of their borders has become a huge challenge. Until now no accepted method exists to achieve accurate fine-tuning: i.e. the notion of breakpoint (BP is still an open issue, and despite repeated regions are vital to understand evolution they are not taken into account in most of the GR detection and refinement methods. Methods and results We propose a method to refine the borders of GR including repeated regions. Instead of removing these repetitions to facilitate computation, we take advantage of them using a consensus alignment sequence of the repeated region in between two blocks. Using the concept of identity vectors for Synteny Blocks (SB and repetitions, a Finite State Machine is designed to detect transition points in the difference between such vectors. The method does not force the BP to be a region or a point but depends on the alignment transitions within the SBs and repetitions. Conclusion The accurate definition of the borders of SB and repeated genomic regions and consequently the detection of BP might help to understand the evolutionary model of species. In this manuscript we present a new proposal for such a refinement. Features of the SBs borders and BPs are different and fit with what is expected. SBs with more diversity in annotations and BPs short and richer in DNA replication and stress response, which are strongly linked with rearrangements.

Comparison of different methods to include recycling in LCAs of aluminium cans and disposable polystyrene cups

NARCIS (Netherlands)

Harst-Wintraecken, van der Eugenie; Potting, José; Kroeze, Carolien

2016-01-01

Many methods have been reported and used to include recycling in life cycle assessments (LCAs). This paper evaluates six widely used methods: three substitution methods (i.e. substitution based on equal quality, a correction factor, and alternative material), allocation based on the number of

A proposed method of measuring the electric-dipole moment of the neutron by ultracold neutron interferometry

International Nuclear Information System (INIS)

Freedman, M.S.; Peshkin, M.; Ringo, G.R.; Dombeck, T.W.

1989-08-01

The use of an ultracold neutron interferometer incorporating an electrostatic accelerator having a strong electric field gradient to accelerate neutrons by their possible electric dipole moment is proposed as a method of measuring the neutron electric dipole moment. The method appears to have the possibility of extending the sensitivity of the measurement by several orders of magnitude, perhaps to 10 -30 e-cm. 9 refs., 3 figs

A new ART iterative method and a comparison of performance among various ART methods

International Nuclear Information System (INIS)

Tan, Yufeng; Sato, Shunsuke

1993-01-01

Many algebraic reconstruction techniques (ART) image reconstruction algorithms, for instance, simultaneous iterative reconstruction technique (SIRT), the relaxation method and multiplicative ART (MART), have been proposed and their convergent properties have been studied. SIRT and the underrelaxed relaxation method converge to the least-squares solution, but the convergent speeds are very slow. The Kaczmarz method converges very quickly, but the reconstructed images contain a lot of noise. The comparative studies between these algorithms have been done by Gilbert and others, but are not adequate. In this paper, we (1) propose a new method which is a modified Kaczmarz method and prove its convergence property, (2) study performance of 7 algorithms including the one proposed here by computer simulation for 3 kinds of typical phantoms. The method proposed here does not give the least-square solution, but the root mean square errors of its reconstructed images decrease very quickly after few interations. The result shows that the method proposed here gives a better reconstructed image. (author)

Determination of the oxidizing property: proposal of an alternative method based on differential scanning calorimetry

International Nuclear Information System (INIS)

Gigante, L.; Dellavedova, M.; Pasturenzi, C.; Lunghi, A.; Mattarella, M.; Cardillo, P.

2008-01-01

Determination of chemical-physical and hazardous properties of substances is a very important matter in the chemical industry, considering the growing attention of public opinion regarding safety and eco-compatibility aspects of products. In the present work, attention was focused on characterization of oxidizing properties. In case of solid compounds, the current method (Dir 84/449/CEE 6) compares the maximum combustion rate of the examined substance to the maximum combustion rate of a reference mixture. This method shows a lot of disvantages and does not provide a quantitative result. In the following work an alternative method, based on DSC measurements, is proposed for the determination of oxidizing properties. [it

Proposal for a method to estimate nutrient shock effects in bacteria

Directory of Open Access Journals (Sweden)

Azevedo Nuno F

2012-08-01

Full Text Available Abstract Background Plating methods are still the golden standard in microbiology; however, some studies have shown that these techniques can underestimate the microbial concentrations and diversity. A nutrient shock is one of the mechanisms proposed to explain this phenomenon. In this study, a tentative method to assess nutrient shock effects was tested. Findings To estimate the extent of nutrient shock effects, two strains isolated from tap water (Sphingomonas capsulata and Methylobacterium sp. and two culture collection strains (E. coli CECT 434 and Pseudomonas fluorescens ATCC 13525 were exposed both to low and high nutrient conditions for different times and then placed in low nutrient medium (R2A and rich nutrient medium (TSA. The average improvement (A.I. of recovery between R2A and TSA for the different times was calculated to more simply assess the difference obtained in culturability between each medium. As expected, A.I. was higher when cells were plated after the exposition to water than when they were recovered from high-nutrient medium showing the existence of a nutrient shock for the diverse bacteria used. S. capsulata was the species most affected by this phenomenon. Conclusions This work provides a method to consistently determine the extent of nutrient shock effects on different microorganisms and hence quantify the ability of each species to deal with sudden increases in substrate concentration.

A method for the computation of turbulent polymeric liquids including hydrodynamic interactions and chain entanglements

Energy Technology Data Exchange (ETDEWEB)

Kivotides, Demosthenes, E-mail: demosthenes.kivotides@strath.ac.uk

2017-02-12

An asymptotically exact method for the direct computation of turbulent polymeric liquids that includes (a) fully resolved, creeping microflow fields due to hydrodynamic interactions between chains, (b) exact account of (subfilter) residual stresses, (c) polymer Brownian motion, and (d) direct calculation of chain entanglements, is formulated. Although developed in the context of polymeric fluids, the method is equally applicable to turbulent colloidal dispersions and aerosols. - Highlights: • An asymptotically exact method for the computation of polymer and colloidal fluids is developed. • The method is valid for all flow inertia and all polymer volume fractions. • The method models entanglements and hydrodynamic interactions between polymer chains.

Contribution for an Urban Geomorphoheritage Assessment Method: Proposal from Three Geomorphosites in Rome (Italy

Directory of Open Access Journals (Sweden)

Pica Alessia

2017-09-01

Full Text Available Urban geomorphology has important implications in spatial planning of human activities, and it also has a geotouristic potential due to the relationship between cultural and geomorphological heritage. Despite the introduction of the term Anthropocene to describe the deep influence that human activities have had in recent times on Earth evolution, urban geomorphological heritage studies are relatively rare and limited and urban geotourism development is recent. The analysis of the complex urban landscape often need the integration of multidisciplinary data. This study aims to propose the first urban geomorphoheritage assessment method, which originates after long-lasting previous geomorphological and geotouristic studies on Rome city centre, it depict rare examples of the geomorphological mapping of a metropolis and, at the same time, of an inventory of urban geomorphosites. The proposal is applied to geomorphosites in the Esquilino neighbourhood of Rome, whose analysis confirm the need for an ad hoc method for assessing urban geomorphosites, as already highlighted in the most recent literature on the topic. The urban geomorphoheritage assessment method is based on: (i the urban geomorphological analysis by means of multitemporal and multidisciplinary data; (ii the geomorphosite inventory; and (iii the geomorphoheritage assessment and enhancement. One challenge is to assess invisible geomorphosites that are widespread in urban context. To this aim, we reworked the attributes describing the Value of a site for Geotourism in order to build up a specific methodology for the analysis of the urban geomorphological heritage.

Development of calculation method for one-dimensional kinetic analysis in fission reactors, including feedback effects

International Nuclear Information System (INIS)

Paixao, S.B.; Marzo, M.A.S.; Alvim, A.C.M.

1986-01-01

The calculation method used in WIGLE code is studied. Because of the non availability of such a praiseworthy solution, expounding the method minutely has been tried. This developed method has been applied for the solution of the one-dimensional, two-group, diffusion equations in slab, axial analysis, including non-boiling heat transfer, accountig for feedback. A steady-state program (CITER-1D), written in FORTRAN 4, has been implemented, providing excellent results, ratifying the developed work quality. (Author) [pt

Calculation of proton-deuteron phase parameters including the Coulomb force

International Nuclear Information System (INIS)

Alt, E.O.; Sandhas, W.; Ziegelmann, H.

1985-04-01

A previously proposed exact method for including the Coulomb force in three-body collisions is applied to proton-deuteron scattering. We present phase shifts for angular momenta up to L=9, from elastic threshold to 50 MeV proton laboratory energy. Separable rank-one potentials are taken for the nuclear interactions. A charge-independent and a charge-symmetric choise, while leading to different neutron-deuteron and proton-deuteron phase parameters, nevertheless yields practically the same Coulomb corrections. We, moreover, investigate the question of P-wave resonances.A critical comparison of our results with those obtained in a co-ordinate space formalism is performed. Furthermore, proposals for an approximate inclusion of the Coulomb potential are tested, and found unsatisfactory. (orig.)

Evaluation of energy policy. [Including proposal by American Inst. of Architects

Energy Technology Data Exchange (ETDEWEB)

Windheim, L S

1977-02-01

It has been evident to some future-looking individuals for some time that both the availability of abundant cheap energy supplies and the exponential increasing use of unlimited amounts must change. However, official energy policy thinking in the U.S. either fails to believe that 'times have changed' or, if believing, is responding in a deleterious and counter-productive manner. This fantastically pervasive and interactive problem cannot be dealt with in the long run by any policy of 'normalizing', of trying to return to doing more with more. The more successful the U.S. is in maintaining or increasing its total energy consumption under conditions of declining net energy, or striving for simplistic first-law efficiencies without analyzing the second level or entropy effects or realizing that every energy exchange adds a minute but rapidly aggregating portion to the environmental pollution limit--doing more with more--the more rapidly inflation, unemployment, and general economic instability will increase. A small group of architectural professionals, the American Institute of Architects, has proposed an alternate energy strategy, essentially doing more with less which, if pursued, can provide more jobs, less inflation, less pollution, and the potential for better matching of energy task and source (entropy efficiency). This strategy exemplifies the characteristics of an appropriate technology response. It stresses capital and energy as well as labor productivity.

A proposal of parameter determination method in the residual strength degradation model for the prediction of fatigue life (I)

International Nuclear Information System (INIS)

Kim, Sang Tae; Jang, Seong Soo

2001-01-01

The static and fatigue tests have been carried out to verify the validity of a generalized residual strength degradation model. And a new method of parameter determination in the model is verified experimentally to account for the effect of tension-compression fatigue loading of spheroidal graphite cast iron. It is shown that the correlation between the experimental results and the theoretical prediction on the statistical distribution of fatigue life by using the proposed method is very reasonable. Furthermore, it is found that the correlation between the theoretical prediction and the experimental results of fatigue life in case of tension-tension fatigue data in composite material appears to be reasonable. Therefore, the proposed method is more adjustable in the determination of the parameter than maximum likelihood method and minimization technique

Precision of glucose measurements in control sera by isotope dilution/mass spectrometry: proposed definitive method compared with a reference method

International Nuclear Information System (INIS)

Pelletier, O.; Arratoon, C.

1987-01-01

This improved isotope-dilution gas chromatographic/mass spectrometric (GC/MS) method, in which [ 13 C]glucose is the internal standard, meets the requirements of a Definitive Method. In a first study with five reconstituted lyophilized sera, a nested analysis of variance of GC/MS values indicated considerable among-vial variation. The CV for 32 measurements per serum ranged from 0.5 to 0.9%. However, concentration and uncertainty values (mmol/L per gram of serum) assigned to one serum by the NBS Definitive Method (7.56 +/- 0.28) were practically identical to those obtained with the proposed method (7.57 +/- 0.20). In the second study, we used twice more [ 13 C]glucose diluent to assay four serum pools and two lyophilized sera. The CV ranged from 0.26 to 0.5% for the serum pools and from 0.28 to 0.59% for the lyophilized sera. In comparison, results by the hexokinase/glucose-6-phosphate dehydrogenase reference method agreed within acceptable limits with those by the Definitive Method but tended to be slightly higher (up to 3%) for lyophilized serum samples or slightly lower (up to 2.5%) for serum pools

Principles, Methods of Participatory Research: Proposal for Draft Animal Power

Directory of Open Access Journals (Sweden)

E. Chia

2004-03-01

Full Text Available The meeting of researchers, who question themselves on the efficiency of their actions when they accompany stakeholders during change processes, provides the opportunity to ponder on the research methods to develop when working together with the stakeholders: participative research, research-action, research-intervention… The author proposes to present the research-action approach as new. If the three phases of research-action are important, the negotiation phase is essential, because it enables contract formalization among partners (ethical aspect, development of a common language, and formalization of structuring efforts between researchers with various specialties and stakeholders. In the research-action approach, the managing set-ups (scientific committees… play a major role: they guarantee at the same time a solution to problems, production, and the legitimacy of the scientific knowledge produced. In conclusion, the author suggests ways to develop research-action in the field of animal traction in order to conceive new socio-technical and organizational innovations that will make the use of this technique easier.

Proposal for a new detection method of substance abuse risk in Croatian adolescents

Directory of Open Access Journals (Sweden)

Sanja Tatalovic Vorkapic

2011-01-01

Full Text Available One of the most important factors of successful substance abuse treatment is the early start of the same treatment. Recent selection method for identification of Croatian adolescents in the substance abuse risk that has been using drug tests from urine samples, has been simple and exact on the one hand, but on the other, has been very rare and usually guided by the pressure of parents or the court. Besides, such method presented the source of legal and ethical questions. So, the proposal of application of standardized psychological tests during systematic medical exams of Croatian adolescents at the age range of 15-22 years could help with the early detection of those adolescents who were in the substance abuse risk or already had the developed addiction problem.

A Proposal of a Method to Measure and Evaluate the Effect to Apply External Support Measures for Owners by Construction Management Method, etc

Science.gov (United States)

Tada, Hiroshi; Miyatake, Ichiro; Mouri, Junji; Ajiki, Norihiko; Fueta, Toshiharu

In Japan, various approaches have been taken to ensure the quality of public works or to support the procurement regime of the governmental agencies, as a means to utilize external resources, which include the procurement support service or the construction management (CM) method. Although discussions on these measures to utilize external resources (hereinafter referred to as external support measure) have been going on, as well as the follow-up surveys showing the positive effects of such measures have been conducted, the surveys only deal with the matters concerning the overall effects of the external support measure on the whole, meaning that the effect of each item of the tasks have not been addressed, and that the extent it dealt with the expectations of the client is unknown. However, the effective use of the external support measure in future cannot be achieved without knowing what was the purpose to introduce the external support measure, and what effect was expected on each task item, and what extent the expectation fulfilled. Furthermore, it is important to clarify not only the effect as compared to the client's expectation (performance), but also the public benefit of this measure (value improvement). From this point of view, there is not an established method to figure out the effect of the client's measure to utilize external resources. In view of this background, this study takes the CM method as an example of the external support measure, and proposes a method to measure and evaluate the effect by each task item, and suggests the future issues and possible responses, in the aim of contributing the promotion, improvement, and proper implementation of the external support measures in future.

Complete Tangent Stiffness for eXtended Finite Element Method by including crack growth parameters

DEFF Research Database (Denmark)

Mougaard, J.F.; Poulsen, P.N.; Nielsen, L.O.

2013-01-01

the crack geometry parameters, such as the crack length and the crack direction directly in the virtual work formulation. For efficiency, it is essential to obtain a complete tangent stiffness. A new method in this work is presented to include an incremental form the crack growth parameters on equal terms......The eXtended Finite Element Method (XFEM) is a useful tool for modeling the growth of discrete cracks in structures made of concrete and other quasi‐brittle and brittle materials. However, in a standard application of XFEM, the tangent stiffness is not complete. This is a result of not including...... with the degrees of freedom in the FEM‐equations. The complete tangential stiffness matrix is based on the virtual work together with the constitutive conditions at the crack tip. Introducing the crack growth parameters as direct unknowns, both equilibrium equations and the crack tip criterion can be handled...

Method for assessment of stormwater treatment facilities - Synthetic road runoff addition including micro-pollutants and tracer.

Science.gov (United States)

Cederkvist, Karin; Jensen, Marina B; Holm, Peter E

2017-08-01

Stormwater treatment facilities (STFs) are becoming increasingly widespread but knowledge on their performance is limited. This is due to difficulties in obtaining representative samples during storm events and documenting removal of the broad range of contaminants found in stormwater runoff. This paper presents a method to evaluate STFs by addition of synthetic runoff with representative concentrations of contaminant species, including the use of tracer for correction of removal rates for losses not caused by the STF. A list of organic and inorganic contaminant species, including trace elements representative of runoff from roads is suggested, as well as relevant concentration ranges. The method was used for adding contaminants to three different STFs including a curbstone extension with filter soil, a dual porosity filter, and six different permeable pavements. Evaluation of the method showed that it is possible to add a well-defined mixture of contaminants despite different field conditions by having a flexibly system, mixing different stock-solutions on site, and use bromide tracer for correction of outlet concentrations. Bromide recovery ranged from only 12% in one of the permeable pavements to 97% in the dual porosity filter, stressing the importance of including a conservative tracer for correction of contaminant retention values. The method is considered useful in future treatment performance testing of STFs. The observed performance of the STFs is presented in coming papers. Copyright © 2017 Elsevier Ltd. All rights reserved.

Designing monitoring programs for chemicals of emerging concern in potable reuse--what to include and what not to include?

Science.gov (United States)

Drewes, J E; Anderson, P; Denslow, N; Olivieri, A; Schlenk, D; Snyder, S A; Maruya, K A

2013-01-01

This study discussed a proposed process to prioritize chemicals for reclaimed water monitoring programs, selection of analytical methods required for their quantification, toxicological relevance of chemicals of emerging concern regarding human health, and related issues. Given that thousands of chemicals are potentially present in reclaimed water and that information about those chemicals is rapidly evolving, a transparent, science-based framework was developed to guide prioritization of which compounds of emerging concern (CECs) should be included in reclaimed water monitoring programs. The recommended framework includes four steps: (1) compile environmental concentrations (e.g., measured environmental concentration or MEC) of CECs in the source water for reuse projects; (2) develop a monitoring trigger level (MTL) for each of these compounds (or groups thereof) based on toxicological relevance; (3) compare the environmental concentration (e.g., MEC) to the MTL; CECs with a MEC/MTL ratio greater than 1 should be prioritized for monitoring, compounds with a ratio less than '1' should only be considered if they represent viable treatment process performance indicators; and (4) screen the priority list to ensure that a commercially available robust analytical method is available for that compound.

75 FR 3925 - Proposed Information Collection Request for Administrative Procedures-20 CFR 601 Including Form...

Science.gov (United States)

2010-01-25

... provided in the desired format, reporting burden (time and financial resources) is minimized, collection... prescribes the use of Form MA 8-7, Transmittal for Unemployment Insurance Materials. This simple check off... interested in comments that: Evaluate whether the proposed collection of information is necessary for the...

FIFRA Peer Review: Proposed Risk Assessment Methods Process

Science.gov (United States)

From September 11-14, 2012, EPA participated in a Federal Insecticide, Fungicide and Rodenticide Act Scientific Advisory Panel (SAP) meeting on a proposed pollinator risk assessment framework for determining the potential risks of pesticides to honey bees.

Method and apparatus for controlling a powertrain system including a multi-mode transmission

Science.gov (United States)

Hessell, Steven M.; Morris, Robert L.; McGrogan, Sean W.; Heap, Anthony H.; Mendoza, Gil J.

2015-09-08

A powertrain including an engine and torque machines is configured to transfer torque through a multi-mode transmission to an output member. A method for controlling the powertrain includes employing a closed-loop speed control system to control torque commands for the torque machines in response to a desired input speed. Upon approaching a power limit of a power storage device transferring power to the torque machines, power limited torque commands are determined for the torque machines in response to the power limit and the closed-loop speed control system is employed to determine an engine torque command in response to the desired input speed and the power limited torque commands for the torque machines.

Reliability and limitation of various diagnostic methods including nuclear medicine in myocardial disease

International Nuclear Information System (INIS)

Tokuyasu, Yoshiki; Kusakabe, Kiyoko; Yamazaki, Toshio

1981-01-01

Electrocardiography (ECG), echocardiography, nuclear method, cardiac catheterization, left ventriculography and endomyocardial biopsy (biopsy) were performed in 40 cases of cardiomyopathy (CM), 9 of endocardial fibroelastosis and 19 of specific heart muscle disease, and the usefulness and limitation of each method was comparatively estimated. In CM, various methods including biopsy were performed. The 40 patients were classified into 3 groups, i.e., hypertrophic (17), dilated (20) and non-hypertrophic.non-dilated (3) on the basis of left ventricular ejection fraction and hypertrophy of the ventricular wall. The hypertrophic group was divided into 4 subgroups: 9 septal, 4 apical, 2 posterior and 2 anterior. The nuclear study is useful in assessing the site of the abnormal ventricular thickening, perfusion defect and ventricular function. Echocardiography is most useful in detecting asymmetric septal hypertrophy. The biopsy gives the sole diagnostic clue, especially in non-hypertrophic.non-dilated cardiomyopathy. ECG is useful in all cases but correlation with the site of disproportional hypertrophy was not obtained. (J.P.N.)

Proposed efficient method for ticket booking (PEMTB) | Ahmed ...

African Journals Online (AJOL)

Journal of Fundamental and Applied Sciences. Journal Home ... We used angular JS, ionic for a front end and node.js, express.js for a back end and mongo DB for a database. ... Our proposed system is totally softcopy and in digitalized.

Proposal of Screening Method of Sleep Disordered Breathing Using Fiber Grating Vision Sensor

Science.gov (United States)

Aoki, Hirooki; Nakamura, Hidetoshi; Nakajima, Masato

Every conventional respiration monitoring technique requires at least one sensor to be attached to the body of the subject during measurement, thereby imposing a sense of restraint that results in aversion against measurements that would last over consecutive days. To solve this problem, we developed a respiration monitoring system for sleepers, and it uses a fiber-grating vision sensor, which is a type of active image sensor to achieve non-contact respiration monitoring. In this paper, we verified the effectiveness of the system, and proposed screening method of the sleep disordered breathing. It was shown that our system could equivalently measure the respiration with thermistor and accelerograph. And, the respiratory condition of sleepers can be grasped by our screening method in one look, and it seems to be useful for the support of the screening of sleep disordered breathing.

A convolution method for predicting mean treatment dose including organ motion at imaging

International Nuclear Information System (INIS)

Booth, J.T.; Zavgorodni, S.F.; Royal Adelaide Hospital, SA

2000-01-01

Full text: The random treatment delivery errors (organ motion and set-up error) can be incorporated into the treatment planning software using a convolution method. Mean treatment dose is computed as the convolution of a static dose distribution with a variation kernel. Typically this variation kernel is Gaussian with variance equal to the sum of the organ motion and set-up error variances. We propose a novel variation kernel for the convolution technique that additionally considers the position of the mobile organ in the planning CT image. The systematic error of organ position in the planning CT image can be considered random for each patient over a population. Thus the variance of the variation kernel will equal the sum of treatment delivery variance and organ motion variance at planning for the population of treatments. The kernel is extended to deal with multiple pre-treatment CT scans to improve tumour localisation for planning. Mean treatment doses calculated with the convolution technique are compared to benchmark Monte Carlo (MC) computations. Calculations of mean treatment dose using the convolution technique agreed with MC results for all cases to better than ± 1 Gy in the planning treatment volume for a prescribed 60 Gy treatment. Convolution provides a quick method of incorporating random organ motion (captured in the planning CT image and during treatment delivery) and random set-up errors directly into the dose distribution. Copyright (2000) Australasian College of Physical Scientists and Engineers in Medicine

A proposed method for fast determination of plasma parameters

International Nuclear Information System (INIS)

Braams, B.J.; Lackner, K.

1984-09-01

The method of function parametrization, developed and applied by H. Wind for fast data evaluation in high energy physics, is presented in the context of controlled fusion research. This method relies on statistical analysis of a data base of simulated experiments in order to obtain a functional representation for the intrinsic physical parameters of a system in terms of the values of the measurements. Some variations on Wind's original procedure are suggested. A specific application for tokamak experiments would be the determination of certain global parameters of the plasma, characterizing the current profile, shape of the cross-section, plasma pressure, and the internal inductance. The relevant measurements for this application include values of the poloidal field and flux external to the plasma, and a diamagnetic measurement. These may be combined with other diagnostics, such as electron-cyclotron emission and laser interferometry, in order to obtain also density and temperature profiles. There appears to be a capability for on-line determination of basic physical parameters, in a millisecond timescale on a minicomputer instead of in seconds on a large mainframe. (orig.)

Methods of forming aluminum oxynitride-comprising bodies, including methods of forming a sheet of transparent armor

Science.gov (United States)

Chu, Henry Shiu-Hung [Idaho Falls, ID; Lillo, Thomas Martin [Idaho Falls, ID

2008-12-02

The invention includes methods of forming an aluminum oxynitride-comprising body. For example, a mixture is formed which comprises A:B:C in a respective molar ratio in the range of 9:3.6-6.2:0.1-1.1, where "A" is Al.sub.2O.sub.3, "B" is AlN, and "C" is a total of one or more of B.sub.2O.sub.3, SiO.sub.2, Si--Al--O--N, and TiO.sub.2. The mixture is sintered at a temperature of at least 1,600.degree. C. at a pressure of no greater than 500 psia effective to form an aluminum oxynitride-comprising body which is at least internally transparent and has at least 99% maximum theoretical density.

Engine including hydraulically actuated valvetrain and method of valve overlap control

Science.gov (United States)

Cowgill, Joel [White Lake, MI

2012-05-08

An exhaust valve control method may include displacing an exhaust valve in communication with the combustion chamber of an engine to an open position using a hydraulic exhaust valve actuation system and returning the exhaust valve to a closed position using the hydraulic exhaust valve actuation assembly. During closing, the exhaust valve may be displaced for a first duration from the open position to an intermediate closing position at a first velocity by operating the hydraulic exhaust valve actuation assembly in a first mode. The exhaust valve may be displaced for a second duration greater than the first duration from the intermediate closing position to a fully closed position at a second velocity at least eighty percent less than the first velocity by operating the hydraulic exhaust valve actuation assembly in a second mode.

Relating two proposed methods for speedup of algorithms for fitting two- and three-way principal component and related multilinear models

NARCIS (Netherlands)

Kiers, Henk A.L.; Harshman, Richard A.

Multilinear analysis methods such as component (and three-way component) analysis of very large data sets can become very computationally demanding and even infeasible unless some method is used to compress the data and/or speed up the algorithms. We discuss two previously proposed speedup methods.

Validation of Proposed "DSM-5" Criteria for Autism Spectrum Disorder

Science.gov (United States)

Frazier, Thomas W.; Youngstrom, Eric A.; Speer, Leslie; Embacher, Rebecca; Law, Paul; Constantino, John; Findling, Robert L.; Hardan, Antonio Y.; Eng, Charis

2012-01-01

Objective: The primary aim of the present study was to evaluate the validity of proposed "DSM-5" criteria for autism spectrum disorder (ASD). Method: We analyzed symptoms from 14,744 siblings (8,911 ASD and 5,863 non-ASD) included in a national registry, the Interactive Autism Network. Youth 2 through 18 years of age were included if at least one…

Designing monitoring programs for chemicals of emerging concern in potable reuse ⋯ What to include and what not to include?

KAUST Repository

Drewes, Jorg; Anderson, Paul D.; Denslow, Nancy D.; Olivieri, Adam W.; Schlenk, Daniel K.; Snyder, Shane A.; Maruya, Keith

2012-01-01

This study discussed a proposed process to prioritize chemicals for reclaimed water monitoring programs, selection of analytical methods required for their quantification, toxicological relevance of chemicals of emerging concern regarding human health, and related issues. Given that thousands of chemicals are potentially present in reclaimed water and that information about those chemicals is rapidly evolving, a transparent, science-based framework was developed to guide prioritization of which compounds of emerging concern (CECs) should be included in reclaimed water monitoring programs. The recommended framework includes four steps: (1) compile environmental concentrations (e.g., measured environmental concentration or MEC) of CECs in the source water for reuse projects; (2) develop a monitoring trigger level (MTL) for each of these compounds (or groups thereof) based on toxicological relevance; (3) compare the environmental concentration (e.g., MEC) to the MTL; CECs with a MEC/MTL ratio greater than 1 should be prioritized for monitoring, compounds with a ratio less than '1' should only be considered if they represent viable treatment process performance indicators; and (4) screen the priority list to ensure that a commercially available robust analytical method is available for that compound. © IWA Publishing 2013.

Designing monitoring programs for chemicals of emerging concern in potable reuse ⋯ What to include and what not to include?

KAUST Repository

Drewes, Jorg

2012-11-01

This study discussed a proposed process to prioritize chemicals for reclaimed water monitoring programs, selection of analytical methods required for their quantification, toxicological relevance of chemicals of emerging concern regarding human health, and related issues. Given that thousands of chemicals are potentially present in reclaimed water and that information about those chemicals is rapidly evolving, a transparent, science-based framework was developed to guide prioritization of which compounds of emerging concern (CECs) should be included in reclaimed water monitoring programs. The recommended framework includes four steps: (1) compile environmental concentrations (e.g., measured environmental concentration or MEC) of CECs in the source water for reuse projects; (2) develop a monitoring trigger level (MTL) for each of these compounds (or groups thereof) based on toxicological relevance; (3) compare the environmental concentration (e.g., MEC) to the MTL; CECs with a MEC/MTL ratio greater than 1 should be prioritized for monitoring, compounds with a ratio less than \\'1\\' should only be considered if they represent viable treatment process performance indicators; and (4) screen the priority list to ensure that a commercially available robust analytical method is available for that compound. © IWA Publishing 2013.

Proposed method for regulating major materials licensees

International Nuclear Information System (INIS)

1992-02-01

The Director, Office of Nuclear Material Safety and Safeguards, US Nuclear Regulatory Commission, appointed a Materials Regulatory Review Task Force to conduct a broad-based review of the Commission's current licensing and oversight programs for fuel cycle and large materials plants. The task force, as requested, defined the components and subcomponents of an ideal regulatory evaluation system for these types of licensed plants and compared they to the components and subcomponents of the existing regulatory evaluation system. This report discusses findings from this comparison and proposed recommendations on the basis of these findings

Proposal for a Method for Business Model Performance Assessment: Toward an Experimentation Tool for Business Model Innovation

Directory of Open Access Journals (Sweden)

Antonio Batocchio

2017-04-01

Full Text Available The representation of business models has been recently widespread, especially in the pursuit of innovation. However, defining a company’s business model is sometimes limited to discussion and debates. This study observes the need for performance measurement so that business models can be data-driven. To meet this goal, the work proposed as a hypothesis the creation of a method that combines the practices of the Balanced Scorecard with a method of business models representation – the Business Model Canvas. Such a combination was based on study of conceptual adaptation, resulting in an application roadmap. A case study application was performed to check the functionality of the proposition, focusing on startup organizations. It was concluded that based on the performance assessment of the business model it is possible to propose the search for change through experimentation, a path that can lead to business model innovation.

Proposta de um quadro de referência para integrar o consumidor nos conceitos de redes [Proposed Reference Table to Include the Consumer in Network Concepts

Directory of Open Access Journals (Sweden)

Ernesto Michelangelo Giglio

2011-06-01

Full Text Available O artigo apresenta uma proposta e defesa da inclusão do ator consumidor nos raciocínios e pesquisas sobre redes, a partir da teoria das redes sociais. A proposta decorre da análise e reflexão sobre 82 artigos de redes selecionados, cujos objetivos incluíam o consumidor. Esta análise mostrou que o consumidor está ausente como ator, tanto teoricamente, quanto nas sugestões gerenciais. Seu papel na rede é secundário e são raros os estudos sobre a gestão de sua participação. Entre as causas dessa ausência, destacam-se a dominância de modelos sócio técnicos de redes na bibliografia e o uso de teorias da psicologia do indivíduo, quando se aborda o consumidor, o que se entende como inadequado num raciocínio de redes a partir das redes sociais. Nas conclusões, propõe-se um conjunto de princípios que inclui o consumidor como ator da rede, ampliando o campo de reflexões e de pesquisas da área. --- Proposed Reference Table to Include the Consumer in Network Concepts --- Abstract --- The article presents a model that includes the consumer in the principles and research on networks, using the concepts of social networks. The model arises from the analysis and reflections of 82 articles about networks, whose objectives included the consumer. It showed that he/she is absent as an actor in both theoretically and management proposals. His/her role in the network is secondary and there are few studies into the management of his/her participation. Among the causes of this absence we identify the dominance of socio-technical models in the bibliography and the use of theories of individual psychology, which are inadequate in a reasoning of social networks. Finally we propose a set of principles that includes the consumer as an actor in a network, widening the reflections and research in this area.

Teaching Methods in Biology Education and Sustainability Education Including Outdoor Education for Promoting Sustainability—A Literature Review

Directory of Open Access Journals (Sweden)

Eila Jeronen

2016-12-01

Full Text Available There are very few studies concerning the importance of teaching methods in biology education and environmental education including outdoor education for promoting sustainability at the levels of primary and secondary schools and pre-service teacher education. The material was selected using special keywords from biology and sustainable education in several scientific databases. The article provides an overview of 24 selected articles published in peer-reviewed scientific journals from 2006–2016. The data was analyzed using qualitative content analysis. Altogether, 16 journals were selected and 24 articles were analyzed in detail. The foci of the analyses were teaching methods, learning environments, knowledge and thinking skills, psychomotor skills, emotions and attitudes, and evaluation methods. Additionally, features of good methods were investigated and their implications for teaching were emphasized. In total, 22 different teaching methods were found to improve sustainability education in different ways. The most emphasized teaching methods were those in which students worked in groups and participated actively in learning processes. Research points toward the value of teaching methods that provide a good introduction and supportive guidelines and include active participation and interactivity.

Proposed method to produce a highly polarized e+ beam for future linear colliders

International Nuclear Information System (INIS)

Okugi, Toshiyuki; Chiba, Masami; Kurihara, Yoshimasa

1996-01-01

We propose a method to produce a spin-polarized e + beam using e + e - pair-creation by circularly polarized photons. Assuming Compton scattering of an unpolarized e - beam and circularly polarized laser light, scattered γ-rays at the high end of the energy spectrum are also circularly polarized. If those γ-rays are utilized to create e ± pairs on a thin target, the spin-polarization is preserved for e + 's at the high end of their energy spectrum. By using the injector linac of Accelerator Test Facility at KEK and a commercially available Nd:YAG pulse laser, we can expect about 10 5 polarized e + 's per second with a degree of polarization of 80% and a kinetic energy of 35-80 MeV. The apparatus for creation and measurement of polarized e + 's is being constructed. We present new idea for possible application of our method to future linear colliders by utilizing a high-power CO 2 laser. (author)

Sensitivity analysis of a complex, proposed geologic waste disposal system using the Fourier Amplitude Sensitivity Test method

International Nuclear Information System (INIS)

Lu Yichi; Mohanty, Sitakanta

2001-01-01

The Fourier Amplitude Sensitivity Test (FAST) method has been used to perform a sensitivity analysis of a computer model developed for conducting total system performance assessment of the proposed high-level nuclear waste repository at Yucca Mountain, Nevada, USA. The computer model has a large number of random input parameters with assigned probability density functions, which may or may not be uniform, for representing data uncertainty. The FAST method, which was previously applied to models with parameters represented by the uniform probability distribution function only, has been modified to be applied to models with nonuniform probability distribution functions. Using an example problem with a small input parameter set, several aspects of the FAST method, such as the effects of integer frequency sets and random phase shifts in the functional transformations, and the number of discrete sampling points (equivalent to the number of model executions) on the ranking of the input parameters have been investigated. Because the number of input parameters of the computer model under investigation is too large to be handled by the FAST method, less important input parameters were first screened out using the Morris method. The FAST method was then used to rank the remaining parameters. The validity of the parameter ranking by the FAST method was verified using the conditional complementary cumulative distribution function (CCDF) of the output. The CCDF results revealed that the introduction of random phase shifts into the functional transformations, proposed by previous investigators to disrupt the repetitiveness of search curves, does not necessarily improve the sensitivity analysis results because it destroys the orthogonality of the trigonometric functions, which is required for Fourier analysis

The discrete ordinate method in association with the finite-volume method in non-structured mesh; Methode des ordonnees discretes associee a la methode des volumes finis en maillage non structure

Energy Technology Data Exchange (ETDEWEB)

Le Dez, V; Lallemand, M [Ecole Nationale Superieure de Mecanique et d` Aerotechnique (ENSMA), 86 - Poitiers (France); Sakami, M; Charette, A [Quebec Univ., Chicoutimi, PQ (Canada). Dept. des Sciences Appliquees

1997-12-31

The description of an efficient method of radiant heat transfer field determination in a grey semi-transparent environment included in a 2-D polygonal cavity with surface boundaries that reflect the radiation in a purely diffusive manner is proposed, at the equilibrium and in radiation-conduction coupling situation. The technique uses simultaneously the finite-volume method in non-structured triangular mesh, the discrete ordinate method and the ray shooting method. The main mathematical developments and comparative results with the discrete ordinate method in orthogonal curvilinear coordinates are included. (J.S.) 10 refs.

The discrete ordinate method in association with the finite-volume method in non-structured mesh; Methode des ordonnees discretes associee a la methode des volumes finis en maillage non structure

Energy Technology Data Exchange (ETDEWEB)

Le Dez, V.; Lallemand, M. [Ecole Nationale Superieure de Mecanique et d`Aerotechnique (ENSMA), 86 - Poitiers (France); Sakami, M.; Charette, A. [Quebec Univ., Chicoutimi, PQ (Canada). Dept. des Sciences Appliquees

1996-12-31

The description of an efficient method of radiant heat transfer field determination in a grey semi-transparent environment included in a 2-D polygonal cavity with surface boundaries that reflect the radiation in a purely diffusive manner is proposed, at the equilibrium and in radiation-conduction coupling situation. The technique uses simultaneously the finite-volume method in non-structured triangular mesh, the discrete ordinate method and the ray shooting method. The main mathematical developments and comparative results with the discrete ordinate method in orthogonal curvilinear coordinates are included. (J.S.) 10 refs.

A proposed architecture and method of operation for improving the protection of privacy and confidentiality in disease registers

Directory of Open Access Journals (Sweden)

Churches Tim

2003-01-01

Full Text Available Abstract Background Disease registers aim to collect information about all instances of a disease or condition in a defined population of individuals. Traditionally methods of operating disease registers have required that notifications of cases be identified by unique identifiers such as social security number or national identification number, or by ensembles of non-unique identifying data items, such as name, sex and date of birth. However, growing concern over the privacy and confidentiality aspects of disease registers may hinder their future operation. Technical solutions to these legitimate concerns are needed. Discussion An alternative method of operation is proposed which involves splitting the personal identifiers from the medical details at the source of notification, and separately encrypting each part using asymmetrical (public key cryptographic methods. The identifying information is sent to a single Population Register, and the medical details to the relevant disease register. The Population Register uses probabilistic record linkage to assign a unique personal identification (UPI number to each person notified to it, although not necessarily everyone in the entire population. This UPI is shared only with a single trusted third party whose sole function is to translate between this UPI and separate series of personal identification numbers which are specific to each disease register. Summary The system proposed would significantly improve the protection of privacy and confidentiality, while still allowing the efficient linkage of records between disease registers, under the control and supervision of the trusted third party and independent ethics committees. The proposed architecture could accommodate genetic databases and tissue banks as well as a wide range of other health and social data collections. It is important that proposals such as this are subject to widespread scrutiny by information security experts, researchers and

Methods of using structures including catalytic materials disposed within porous zeolite materials to synthesize hydrocarbons

Science.gov (United States)

Rollins, Harry W [Idaho Falls, ID; Petkovic, Lucia M [Idaho Falls, ID; Ginosar, Daniel M [Idaho Falls, ID

2011-02-01

Catalytic structures include a catalytic material disposed within a zeolite material. The catalytic material may be capable of catalyzing a formation of methanol from carbon monoxide and/or carbon dioxide, and the zeolite material may be capable of catalyzing a formation of hydrocarbon molecules from methanol. The catalytic material may include copper and zinc oxide. The zeolite material may include a first plurality of pores substantially defined by a crystal structure of the zeolite material and a second plurality of pores dispersed throughout the zeolite material. Systems for synthesizing hydrocarbon molecules also include catalytic structures. Methods for synthesizing hydrocarbon molecules include contacting hydrogen and at least one of carbon monoxide and carbon dioxide with such catalytic structures. Catalytic structures are fabricated by forming a zeolite material at least partially around a template structure, removing the template structure, and introducing a catalytic material into the zeolite material.

Spine surgeon's kinematics during discectomy, part II: operating table height and visualization methods, including microscope.

Science.gov (United States)

Park, Jeong Yoon; Kim, Kyung Hyun; Kuh, Sung Uk; Chin, Dong Kyu; Kim, Keun Su; Cho, Yong Eun

2014-05-01

Surgeon spine angle during surgery was studied ergonomically and the kinematics of the surgeon's spine was related with musculoskeletal fatigue and pain. Spine angles varied depending on operation table height and visualization method, and in a previous paper we showed that the use of a loupe and a table height at the midpoint between the umbilicus and the sternum are optimal for reducing musculoskeletal loading. However, no studies have previously included a microscope as a possible visualization method. The objective of this study is to assess differences in surgeon spine angles depending on operating table height and visualization method, including microscope. We enrolled 18 experienced spine surgeons for this study, who each performed a discectomy using a spine surgery simulator. Three different methods were used to visualize the surgical field (naked eye, loupe, microscope) and three different operating table heights (anterior superior iliac spine, umbilicus, the midpoint between the umbilicus and the sternum) were studied. Whole spine angles were compared for three different views during the discectomy simulation: midline, ipsilateral, and contralateral. A 16-camera optoelectronic motion analysis system was used, and 16 markers were placed from the head to the pelvis. Lumbar lordosis, thoracic kyphosis, cervical lordosis, and occipital angle were compared between the different operating table heights and visualization methods as well as a natural standing position. Whole spine angles differed significantly depending on visualization method. All parameters were closer to natural standing values when discectomy was performed with a microscope, and there were no differences between the naked eye and the loupe. Whole spine angles were also found to differ from the natural standing position depending on operating table height, and became closer to natural standing position values as the operating table height increased, independent of the visualization method

A Proposal of Client Application Architecture using Loosely Coupled Component Connection Method in Banking Branch System

Science.gov (United States)

Someya, Harushi; Mori, Yuichi; Abe, Masahiro; Machida, Isamu; Hasegawa, Atsushi; Yoshie, Osamu

Due to the deregulation of financial industry, the branches in banking industry need to shift to the sales-oriented bases from the operation-oriented bases. For corresponding to this movement, new banking branch systems are being developed. It is the main characteristics of new systems that we bring the form operations that have traditionally been performed at each branch into the centralized operation center for the purpose of rationalization and efficiency of the form operations. The branches treat a wide variety of forms. The forms can be described by common items in many cases, but the items include the different business logic and each form has the different relation among the items. And there is a need to develop the client application by user oneself. Consequently the challenge is to arrange the development environment that is high reusable, easy customizable and user developable. We propose a client application architecture that has a loosely coupled component connection method, and allows developing the applications by only describing the screen configurations and their transitions in XML documents. By adopting our architecture, we developed client applications of the centralized operation center for the latest banking branch system. Our experiments demonstrate good performances.

Proposed Food and Drug Administration protective action guides for human food and animal feed: methods and implementation

International Nuclear Information System (INIS)

Schmidt, G.D.; Shleien, B.; Chiacchierini, R.P.

1978-01-01

The Food and Drug Administration's proposed recommendations to State and local agencies provide guidance on appropriate planning actions necessary for evaluating and preventing radioactive contamination of foods and animal feeds and the control and use of such products should they become contaminated. This presentation will cover the recommendations on implementation of the Preventive and Emergency PAG's. These recommendations include (1) the use of 'Dietary Factors' to obtain PAG's for specific food items from the general guidance, (2) procedures to be used for radionuclide mixtures and other radionuclides, (3) field and laboratory methods for the measurement of the level of contamination in the event of an incident and, (4) protective actions to be implemented by State and local agencies to limit the radiation dose to the public. Specific protective actions which should be considered for implementation when the projected dose exceeds the Preventive PAG are given for application to pasture, milk, fruits and vegetables, and grains. At the Emergency PAG level, the protective action decision is whether condemnation or other disposition is appropriate. (author)

Using a fuzzy comprehensive evaluation method to determine product usability: A proposed theoretical framework.

Science.gov (United States)

Zhou, Ronggang; Chan, Alan H S

2017-01-01

In order to compare existing usability data to ideal goals or to that for other products, usability practitioners have tried to develop a framework for deriving an integrated metric. However, most current usability methods with this aim rely heavily on human judgment about the various attributes of a product, but often fail to take into account of the inherent uncertainties in these judgments in the evaluation process. This paper presents a universal method of usability evaluation by combining the analytic hierarchical process (AHP) and the fuzzy evaluation method. By integrating multiple sources of uncertain information during product usability evaluation, the method proposed here aims to derive an index that is structured hierarchically in terms of the three usability components of effectiveness, efficiency, and user satisfaction of a product. With consideration of the theoretical basis of fuzzy evaluation, a two-layer comprehensive evaluation index was first constructed. After the membership functions were determined by an expert panel, the evaluation appraisals were computed by using the fuzzy comprehensive evaluation technique model to characterize fuzzy human judgments. Then with the use of AHP, the weights of usability components were elicited from these experts. Compared to traditional usability evaluation methods, the major strength of the fuzzy method is that it captures the fuzziness and uncertainties in human judgments and provides an integrated framework that combines the vague judgments from multiple stages of a product evaluation process.

Enhancing the Social Network Dimension of Lifelong Competence Development and Management Systems: A Proposal of Methods and Tools

NARCIS (Netherlands)

Cheak, Alicia; Angehrn, Albert; Sloep, Peter

2006-01-01

Cheak, A. M., Angehrn, A. A., & Sloep, P. (2006). Enhancing the social network dimension of lifelong competence development and management systems: A proposal of methods and tools. In R. Koper & K. Stefanov (Eds.). Proceedings of International Workshop in Learning Networks for Lifelong Competence

Enhancing the Social Network Dimension of Lifelong Competence Development and Management Systems: A proposal of methods and tools

NARCIS (Netherlands)

Cheak, Alicia; Angehrn, Albert; Sloep, Peter

2006-01-01

Cheak, A. M., Angehrn, A. A., & Sloep, P. B. (2006). Enhancing the social network dimension of lifelong competence development and management systems: A proposal of methods and tools. In E. J. R. Koper & K. Stefanov (Eds.), Proceedings of International Workshop on Learning Networks for Lifelong

New Finger Biometric Method Using Near Infrared Imaging

Science.gov (United States)

Lee, Eui Chul; Jung, Hyunwoo; Kim, Daeyeoul

2011-01-01

In this paper, we propose a new finger biometric method. Infrared finger images are first captured, and then feature extraction is performed using a modified Gaussian high-pass filter through binarization, local binary pattern (LBP), and local derivative pattern (LDP) methods. Infrared finger images include the multimodal features of finger veins and finger geometries. Instead of extracting each feature using different methods, the modified Gaussian high-pass filter is fully convolved. Therefore, the extracted binary patterns of finger images include the multimodal features of veins and finger geometries. Experimental results show that the proposed method has an error rate of 0.13%. PMID:22163741

Disintegration of sublingual tablets: proposal for a validated test method and acceptance criterion.

Science.gov (United States)

Weda, M; van Riet-Nales, D A; van Aalst, P; de Kaste, D; Lekkerkerker, J F F

2006-12-01

In the Netherlands the market share of isosorbide dinitrate 5 mg sublingual tablets is dominated by 2 products (A and B). In the last few years complaints have been received from health care professionals on product B. During patient use the disintegration of the tablet was reported to be slow and/or incomplete, and ineffectiveness was experienced. In the European Pharmacopoeia (Ph. Eur.) no requirement is present for the disintegration time of sublingual tablets. The purpose of this study was to compare the in vitro disintegration time of products A and B, and to establish a suitable test method and acceptance criterion. A and B were tested with the Ph. Eur. method described in the monograph on disintegration of tablets and capsules as well as with 3 modified tests using the same Ph. Eur. apparatus, but without movement of the basket-rack assembly. In modified test 1 and modified test 2 water was used as medium (900 ml and 50 ml respectively), whereas in modified test 3 artificial saliva was used (50 ml). In addition, disintegration was tested in Nessler tubes with 0.5 and 2 ml of water. Finally, the Ph. Eur. method was also applied to other sublingual tablets with other drug substances on the Dutch market. With modified test 3 no disintegration could be achieved within 20 min. With the Ph. Eur. method and modified tests 1 and 2 product A and B differed significantly (p disintegration times. These 3 methods were capable of discriminating between products and between batches. The time measured with the Ph. Eur. method was significantly lower compared to modified tests 1 and 2 (p tablets the disintegration time should be tested. The Ph. Eur. method is considered suitable for this test. In view of the products currently on the market and taking into consideration requirements in the United States Pharmacopeia and Japanese Pharmacopoeia, an acceptance criterion of not more than 2 min is proposed.

Generalized Truncated Methods for an Efficient Solution of Retrial Systems

Directory of Open Access Journals (Sweden)

Ma Jose Domenech-Benlloch

2008-01-01

Full Text Available We are concerned with the analytic solution of multiserver retrial queues including the impatience phenomenon. As there are not closed-form solutions to these systems, approximate methods are required. We propose two different generalized truncated methods to effectively solve this type of systems. The methods proposed are based on the homogenization of the state space beyond a given number of users in the retrial orbit. We compare the proposed methods with the most well-known methods appeared in the literature in a wide range of scenarios. We conclude that the proposed methods generally outperform previous proposals in terms of accuracy for the most common performance parameters used in retrial systems with a moderated growth in the computational cost.

Optimal design of power system stabilizer for power systems including doubly fed induction generator wind turbines

International Nuclear Information System (INIS)

Derafshian, Mehdi; Amjady, Nima

2015-01-01

This paper presents an evolutionary algorithm-based approach for optimal design of power system stabilizer (PSS) for multi-machine power systems that include doubly fed induction generator wind turbines. The proposed evolutionary algorithm is an improved particle swarm optimization named chaotic particle swarm optimization with passive congregation (CPSO-PC) applied for finding the optimal settings of PSS parameters. Two different eigenvalue-based objectives are combined as the objective function for the optimization problem of tuning PSS parameters. The first objective function comprises the damping factor of lightly damped electro-mechanical modes and the second one includes the damping ratio of these modes. The effectiveness of the proposed method to design PSS for the power systems including DFIG (Doubly Fed Induction Generator) is extensively demonstrated through eigenvalue analysis and time-domain simulations and also by comparing its simulation results with the results of other heuristic optimization approaches. - Highlights: • A new optimization model for design of PSS in power systems including DFIG is proposed. • A detailed and realistic modeling of DFIG is presented. • A new evolutionary algorithm is suggested for solving the optimization problem of designing PSS

Method of fabricating electrodes including high-capacity, binder-free anodes for lithium-ion batteries

Science.gov (United States)

Ban, Chunmei; Wu, Zhuangchun; Dillon, Anne C.

2017-01-10

An electrode (110) is provided that may be used in an electrochemical device (100) such as an energy storage/discharge device, e.g., a lithium-ion battery, or an electrochromic device, e.g., a smart window. Hydrothermal techniques and vacuum filtration methods were applied to fabricate the electrode (110). The electrode (110) includes an active portion (140) that is made up of electrochemically active nanoparticles, with one embodiment utilizing 3d-transition metal oxides to provide the electrochemical capacity of the electrode (110). The active material (140) may include other electrochemical materials, such as silicon, tin, lithium manganese oxide, and lithium iron phosphate. The electrode (110) also includes a matrix or net (170) of electrically conductive nanomaterial that acts to connect and/or bind the active nanoparticles (140) such that no binder material is required in the electrode (110), which allows more active materials (140) to be included to improve energy density and other desirable characteristics of the electrode. The matrix material (170) may take the form of carbon nanotubes, such as single-wall, double-wall, and/or multi-wall nanotubes, and be provided as about 2 to 30 percent weight of the electrode (110) with the rest being the active material (140).

Time-domain simulation of constitutive relations for nonlinear acoustics including relaxation for frequency power law attenuation media modeling

Science.gov (United States)

Jiménez, Noé; Camarena, Francisco; Redondo, Javier; Sánchez-Morcillo, Víctor; Konofagou, Elisa E.

2015-10-01

We report a numerical method for solving the constitutive relations of nonlinear acoustics, where multiple relaxation processes are included in a generalized formulation that allows the time-domain numerical solution by an explicit finite differences scheme. Thus, the proposed physical model overcomes the limitations of the one-way Khokhlov-Zabolotskaya-Kuznetsov (KZK) type models and, due to the Lagrangian density is implicitly included in the calculation, the proposed method also overcomes the limitations of Westervelt equation in complex configurations for medical ultrasound. In order to model frequency power law attenuation and dispersion, such as observed in biological media, the relaxation parameters are fitted to both exact frequency power law attenuation/dispersion media and also empirically measured attenuation of a variety of tissues that does not fit an exact power law. Finally, a computational technique based on artificial relaxation is included to correct the non-negligible numerical dispersion of the finite difference scheme, and, on the other hand, improve stability trough artificial attenuation when shock waves are present. This technique avoids the use of high-order finite-differences schemes leading to fast calculations. The present algorithm is especially suited for practical configuration where spatial discontinuities are present in the domain (e.g. axisymmetric domains or zero normal velocity boundary conditions in general). The accuracy of the method is discussed by comparing the proposed simulation solutions to one dimensional analytical and k-space numerical solutions.

The clinically-integrated randomized trial: proposed novel method for conducting large trials at low cost

Directory of Open Access Journals (Sweden)

Scardino Peter T

2009-03-01

Full Text Available Abstract Introduction Randomized controlled trials provide the best method of determining which of two comparable treatments is preferable. Unfortunately, contemporary randomized trials have become increasingly expensive, complex and burdened by regulation, so much so that many trials are of doubtful feasibility. Discussion Here we present a proposal for a novel, streamlined approach to randomized trials: the "clinically-integrated randomized trial". The key aspect of our methodology is that the clinical experience of the patient and doctor is virtually indistinguishable whether or not the patient is randomized, primarily because outcome data are obtained from routine clinical data, or from short, web-based questionnaires. Integration of a randomized trial into routine clinical practice also implies that there should be an attempt to randomize every patient, a corollary of which is that eligibility criteria are minimized. The similar clinical experience of patients on- and off-study also entails that the marginal cost of putting an additional patient on trial is negligible. We propose examples of how the clinically-integrated randomized trial might be applied in four distinct areas of medicine: comparisons of surgical techniques, "me too" drugs, rare diseases and lifestyle interventions. Barriers to implementing clinically-integrated randomized trials are discussed. Conclusion The proposed clinically-integrated randomized trial may allow us to enlarge dramatically the number of clinical questions that can be addressed by randomization.

48 CFR 315.605 - Content of unsolicited proposals.

Science.gov (United States)

2010-10-01

... CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Unsolicited Proposals 315.605 Content of... prepared under Government supervision; (b) The methods and approaches stated in the proposal were developed... Title (This certification shall be signed by a responsible management official of the proposing...

A Proposed Methodology for the Conceptualization, Operationalization, and Empirical Validation of the Concept of Information Need

Science.gov (United States)

Afzal, Waseem

2017-01-01

Introduction: The purpose of this paper is to propose a methodology to conceptualize, operationalize, and empirically validate the concept of information need. Method: The proposed methodology makes use of both qualitative and quantitative perspectives, and includes a broad array of approaches such as literature reviews, expert opinions, focus…

Extending Vulnerability Assessment to Include Life Stages Considerations.

Science.gov (United States)

Hodgson, Emma E; Essington, Timothy E; Kaplan, Isaac C

2016-01-01

Species are experiencing a suite of novel stressors from anthropogenic activities that have impacts at multiple scales. Vulnerability assessment is one tool to evaluate the likely impacts that these stressors pose to species so that high-vulnerability cases can be identified and prioritized for monitoring, protection, or mitigation. Commonly used semi-quantitative methods lack a framework to explicitly account for differences in exposure to stressors and organism responses across life stages. Here we propose a modification to commonly used spatial vulnerability assessment methods that includes such an approach, using ocean acidification in the California Current as an illustrative case study. Life stage considerations were included by assessing vulnerability of each life stage to ocean acidification and were used to estimate population vulnerability in two ways. We set population vulnerability equal to: (1) the maximum stage vulnerability and (2) a weighted mean across all stages, with weights calculated using Lefkovitch matrix models. Vulnerability was found to vary across life stages for the six species explored in this case study: two krill-Euphausia pacifica and Thysanoessa spinifera, pteropod-Limacina helicina, pink shrimp-Pandalus jordani, Dungeness crab-Metacarcinus magister and Pacific hake-Merluccius productus. The maximum vulnerability estimates ranged from larval to subadult and adult stages with no consistent stage having maximum vulnerability across species. Similarly, integrated vulnerability metrics varied greatly across species. A comparison showed that some species had vulnerabilities that were similar between the two metrics, while other species' vulnerabilities varied substantially between the two metrics. These differences primarily resulted from cases where the most vulnerable stage had a low relative weight. We compare these methods and explore circumstances where each method may be appropriate.

Development method of Hybrid Energy Storage System, including PEM fuel cell and a battery

Science.gov (United States)

Ustinov, A.; Khayrullina, A.; Borzenko, V.; Khmelik, M.; Sveshnikova, A.

2016-09-01

Development of fuel cell (FC) and hydrogen metal-hydride storage (MH) technologies continuously demonstrate higher efficiency rates and higher safety, as hydrogen is stored at low pressures of about 2 bar in a bounded state. A combination of a FC/MH system with an electrolyser, powered with a renewable source, allows creation of an almost fully autonomous power system, which could potentially replace a diesel-generator as a back-up power supply. However, the system must be extended with an electro-chemical battery to start-up the FC and compensate the electric load when FC fails to deliver the necessary power. Present paper delivers the results of experimental and theoretical investigation of a hybrid energy system, including a proton exchange membrane (PEM) FC, MH- accumulator and an electro-chemical battery, development methodology for such systems and the modelling of different battery types, using hardware-in-the-loop approach. The economic efficiency of the proposed solution is discussed using an example of power supply of a real town of Batamai in Russia.

Development method of Hybrid Energy Storage System, including PEM fuel cell and a battery

International Nuclear Information System (INIS)

Ustinov, A; Khayrullina, A; Khmelik, M; Sveshnikova, A; Borzenko, V

2016-01-01

Development of fuel cell (FC) and hydrogen metal-hydride storage (MH) technologies continuously demonstrate higher efficiency rates and higher safety, as hydrogen is stored at low pressures of about 2 bar in a bounded state. A combination of a FC/MH system with an electrolyser, powered with a renewable source, allows creation of an almost fully autonomous power system, which could potentially replace a diesel-generator as a back-up power supply. However, the system must be extended with an electro-chemical battery to start-up the FC and compensate the electric load when FC fails to deliver the necessary power. Present paper delivers the results of experimental and theoretical investigation of a hybrid energy system, including a proton exchange membrane (PEM) FC, MH- accumulator and an electro-chemical battery, development methodology for such systems and the modelling of different battery types, using hardware-in-the-loop approach. The economic efficiency of the proposed solution is discussed using an example of power supply of a real town of Batamai in Russia. (paper)

Proposed Model for Integrating RAMS Method in the Design Process in Construction

Directory of Open Access Journals (Sweden)

Saad Al-Jibouri

2010-05-01

Full Text Available There is a growing trend in the Netherlands for outsourcing public construction activities to the private sector through the use of integrated contracts. There is also an increasing emphasis from public clients on the use of RAMS and life cycle costing (LCC in the design process of infrastructural projects to improve the performance of designed systems and optimize the project cost. RAMS is an acronym for `reliability, availability, maintainability and safety' and represents a collection of techniques to provide predictions of the performance targets of the required system. Increasingly, RAMS targets are being specified in invitation to tender or contract documents and the parties responsible for the design are required to provide evidence of its application in their design. Recent evidence from practice, complemented with a literature study, has shown that the knowledge and application of RAMS in infrastructural designs are in their infancy compared with other industrial sectors and many designers in construction do not have the necessary knowledge and experience to apply it. This paper describes a proposed model for the integration of RAMS and LCC into the design process in construction. A variation of the model for the application of RAMS in `design, build, finance and maintain' (DBFM contracts that include maintenance requirements is also proposed. The two models involve providing guidelines to simplify the application of RAMs by the designers. The model has been validated for its practicality and usefulness during a workshop by experienced designers. DOI: 10.3763/aedm.2008.0100 Published in the Journal AEDM - Volume 5, Number 4, 2009 , pp. 179-192(14

78 FR 76309 - Agency Information Collection Activities: Proposed Collection: Public Comment Request

Science.gov (United States)

2013-12-17

... dispensed, pricing, sources of support to provide HIV/AIDS medications, eligibility requirements, cost data... enrollment, and cost-saving strategies including coordination with Medicaid). Describe the need for the information and proposed use of the information: The quarterly report represents the best method for HRSA to...

Proposed method for reconstructing velocity profiles using a multi-electrode electromagnetic flow meter

International Nuclear Information System (INIS)

Kollár, László E; Lucas, Gary P; Zhang, Zhichao

2014-01-01

An analytical method is developed for the reconstruction of velocity profiles using measured potential distributions obtained around the boundary of a multi-electrode electromagnetic flow meter (EMFM). The method is based on the discrete Fourier transform (DFT), and is implemented in Matlab. The method assumes the velocity profile in a section of a pipe as a superposition of polynomials up to sixth order. Each polynomial component is defined along a specific direction in the plane of the pipe section. For a potential distribution obtained in a uniform magnetic field, this direction is not unique for quadratic and higher-order components; thus, multiple possible solutions exist for the reconstructed velocity profile. A procedure for choosing the optimum velocity profile is proposed. It is applicable for single-phase or two-phase flows, and requires measurement of the potential distribution in a non-uniform magnetic field. The potential distribution in this non-uniform magnetic field is also calculated for the possible solutions using weight values. Then, the velocity profile with the calculated potential distribution which is closest to the measured one provides the optimum solution. The reliability of the method is first demonstrated by reconstructing an artificial velocity profile defined by polynomial functions. Next, velocity profiles in different two-phase flows, based on results from the literature, are used to define the input velocity fields. In all cases, COMSOL Multiphysics is used to model the physical specifications of the EMFM and to simulate the measurements; thus, COMSOL simulations produce the potential distributions on the internal circumference of the flow pipe. These potential distributions serve as inputs for the analytical method. The reconstructed velocity profiles show satisfactory agreement with the input velocity profiles. The method described in this paper is most suitable for stratified flows and is not applicable to axisymmetric flows in

Flexible barrier film, method of forming same, and organic electronic device including same

Science.gov (United States)

Blizzard, John; Tonge, James Steven; Weidner, William Kenneth

2013-03-26

A flexible barrier film has a thickness of from greater than zero to less than 5,000 nanometers and a water vapor transmission rate of no more than 1.times.10.sup.-2 g/m.sup.2/day at 22.degree. C. and 47% relative humidity. The flexible barrier film is formed from a composition, which comprises a multi-functional acrylate. The composition further comprises the reaction product of an alkoxy-functional organometallic compound and an alkoxy-functional organosilicon compound. A method of forming the flexible barrier film includes the steps of disposing the composition on a substrate and curing the composition to form the flexible barrier film. The flexible barrier film may be utilized in organic electronic devices.

Proposing New Methods to Enhance the Low-Resolution Simulated GPR Responses in the Frequency and Wavelet Domains

Directory of Open Access Journals (Sweden)

Reza Ahmadi

2014-12-01

Full Text Available To date, a number of numerical methods, including the popular Finite-Difference Time Domain (FDTD technique, have been proposed to simulate Ground-Penetrating Radar (GPR responses. Despite having a number of advantages, the finite-difference method also has pitfalls such as being very time consuming in simulating the most common case of media with high dielectric permittivity, causing the forward modelling process to be very long lasting, even with modern high-speed computers. In the present study the well-known hyperbolic pattern response of horizontal cylinders, usually found in GPR B-Scan images, is used as a basic model to examine the possibility of reducing the forward modelling execution time. In general, the simulated GPR traces of common reflected objects are time shifted, as with the Normal Moveout (NMO traces encountered in seismic reflection responses. This suggests the application of Fourier transform to the GPR traces, employing the time-shifting property of the transformation to interpolate the traces between the adjusted traces in the frequency domain (FD. Therefore, in the present study two post-processing algorithms have been adopted to increase the speed of forward modelling while maintaining the required precision. The first approach is based on linear interpolation in the Fourier domain, resulting in increasing lateral trace-to-trace interval of appropriate sampling frequency of the signal, preventing any aliasing. In the second approach, a super-resolution algorithm based on 2D-wavelet transform is developed to increase both vertical and horizontal resolution of the GPR B-Scan images through preserving scale and shape of hidden hyperbola features. Through comparing outputs from both methods with the corresponding actual high-resolution forward response, it is shown that both approaches can perform satisfactorily, although the wavelet-based approach outperforms the frequency-domain approach noticeably, both in amplitude and

Decentralised control method for DC microgrids with improved current sharing accuracy

DEFF Research Database (Denmark)

Yang, Jie; Jin, Xinmin; Wu, Xuezhi

2017-01-01

A decentralised control method that deals with current sharing issues in dc microgrids (MGs) is proposed in this study. The proposed method is formulated in terms of ‘modified global indicator’ concept, which was originally proposed to improve reactive power sharing in ac MGs. In this work......, the ‘modified global indicator’ concept is extended to coordinate dc MGs, which aims to preserve the main features offered by decentralised control methods such as no need of communication links, central controller or knowledge of the microgrid topology and parameters. This global indicator is inserted between...... a shunt virtual resistance. The operation under multiple dc-buses is also included in order to enhance the applicability of the proposed controller. A detailed mathematical model including the effect of network mismatches is derived for analysis of the stability of the proposed controller. The feasibility...

Assessment of SKB's proposal for encapsulation

International Nuclear Information System (INIS)

Lundin, M.; Gustafsson, Oskar; Broemsen, B. von; Troell, E.

2001-01-01

This report accounts for an independent assessment of a proposal regarding manufacturing of copper canisters, which has been presented by SKB (Swedish Nuclear Fuel and Waste Management Co) in cooperation with MABU Consulting. IVF (The Swedish Institute for Production Engineering Research) has performed the assessment by commission of SKI (Swedish Nuclear Power Inspectorate). IVF generally believe that the proposed method, recommended manufacturing equipment and organisation will most likely mean that a functioning manufacturing of canisters can be realised. No significant deficiencies have been identified, which would mean serious problems during the manufacturing process. In some cases IVF recommends a further evaluation regarding proposed methods and/or equipment. Basically these concerns the welding processes. However, it should be stressed that SKB has emphasised that further investigation will be performed regarding this subject. Furthermore IVF recommend that proposed methods and equipment for machining of copper cylinders and for blasting of inserts should be further evaluated

Small Private Online Research: A Proposal for A Numerical Methods Course Based on Technology Use and Blended Learning

Science.gov (United States)

Cepeda, Francisco Javier Delgado

2017-01-01

This work presents a proposed model in blended learning for a numerical methods course evolved from traditional teaching into a research lab in scientific visualization. The blended learning approach sets a differentiated and flexible scheme based on a mobile setup and face to face sessions centered on a net of research challenges. Model is…

Generating region proposals for histopathological whole slide image retrieval.

Science.gov (United States)

Ma, Yibing; Jiang, Zhiguo; Zhang, Haopeng; Xie, Fengying; Zheng, Yushan; Shi, Huaqiang; Zhao, Yu; Shi, Jun

2018-06-01

Content-based image retrieval is an effective method for histopathological image analysis. However, given a database of huge whole slide images (WSIs), acquiring appropriate region-of-interests (ROIs) for training is significant and difficult. Moreover, histopathological images can only be annotated by pathologists, resulting in the lack of labeling information. Therefore, it is an important and challenging task to generate ROIs from WSI and retrieve image with few labels. This paper presents a novel unsupervised region proposing method for histopathological WSI based on Selective Search. Specifically, the WSI is over-segmented into regions which are hierarchically merged until the WSI becomes a single region. Nucleus-oriented similarity measures for region mergence and Nucleus-Cytoplasm color space for histopathological image are specially defined to generate accurate region proposals. Additionally, we propose a new semi-supervised hashing method for image retrieval. The semantic features of images are extracted with Latent Dirichlet Allocation and transformed into binary hashing codes with Supervised Hashing. The methods are tested on a large-scale multi-class database of breast histopathological WSIs. The results demonstrate that for one WSI, our region proposing method can generate 7.3 thousand contoured regions which fit well with 95.8% of the ROIs annotated by pathologists. The proposed hashing method can retrieve a query image among 136 thousand images in 0.29 s and reach precision of 91% with only 10% of images labeled. The unsupervised region proposing method can generate regions as predictions of lesions in histopathological WSI. The region proposals can also serve as the training samples to train machine-learning models for image retrieval. The proposed hashing method can achieve fast and precise image retrieval with small amount of labels. Furthermore, the proposed methods can be potentially applied in online computer-aided-diagnosis systems. Copyright

7 CFR 3405.14 - Proposal review.

Science.gov (United States)

2010-01-01

... Regulations of the Department of Agriculture (Continued) COOPERATIVE STATE RESEARCH, EDUCATION, AND EXTENSION SERVICE, DEPARTMENT OF AGRICULTURE HIGHER EDUCATION CHALLENGE GRANTS PROGRAM Proposal Review and Evaluation § 3405.14 Proposal review. The proposal evaluation process includes both internal staff review and...

Proposal for basic safety requirements regarding the disposal of high-level radioactive waste

International Nuclear Information System (INIS)

1980-04-01

A working group commissioned to prepare proposals for basic safety requirements for the storage and transport of radioactive waste prepared its report to the Danish Agency of Environmental Protection. The proposals include: radiation protection requirements, requirements concerning the properties of high-level waste units, the geological conditions of the waste disposal location, the supervision of waste disposal areas. The proposed primary requirements for safety evaluation of the disposal of high-level waste in deep geological formations are of a general nature, not being tied to specific assumptions regarding the waste itself, the geological and other conditions at the place of disposal, and the technical methods of disposal. It was impossible to test the proposals for requirements on a working repository. As no country has, to the knowledge of the working group, actually disposed of hifg-level radioactive waste or approved of plans for such disposal. Methods for evaluating the suitability of geological formations for waste disposal, and background material concerning the preparation of these proposals for basic safety requirements relating to radiation, waste handling and geological conditions are reviewed. Appended to the report is a description of the phases of the fuel cycle that are related to the storage of spent fuel and the disposal of high-level reprocessing waste in a salt formation. It should be noted that the proposals of the working group are not limited to the disposal of reprocessed fuel, but also include the direct disposal of spent fuel as well as disposal in geological formations other than salt. (EG)

A calibration method for proposed XRF measurements of arsenic and selenium in nail clippings

International Nuclear Information System (INIS)

Gherase, Mihai R; Fleming, David E B

2011-01-01

A calibration method for proposed x-ray fluorescence (XRF) measurements of arsenic and selenium in nail clippings is demonstrated. Phantom nail clippings were produced from a whole nail phantom (0.7 mm thickness, 25 x 25 mm 2 area) and contained equal concentrations of arsenic and selenium ranging from 0 to 20 μg g -1 in increments of 5 μg g -1 . The phantom nail clippings were then grouped in samples of five different masses: 20, 40, 60, 80 and 100 mg for each concentration. Experimental x-ray spectra were acquired for each of the sample masses using a portable x-ray tube and a detector unit. Calibration lines (XRF signal in a number of counts versus stoichiometric elemental concentration) were produced for each of the two elements. A semi-empirical relationship between the mass of the nail phantoms (m) and the slope of the calibration line (s) was determined separately for arsenic and selenium. Using this calibration method, one can estimate elemental concentrations and their uncertainties from the XRF spectra of human nail clippings. (note)

New clinical validation method for automated sphygmomanometer: a proposal by Japan ISO-WG for sphygmomanometer standard.

Science.gov (United States)

Shirasaki, Osamu; Asou, Yosuke; Takahashi, Yukio

2007-12-01

Owing to fast or stepwise cuff deflation, or measuring at places other than the upper arm, the clinical accuracy of most recent automated sphygmomanometers (auto-BPMs) cannot be validated by one-arm simultaneous comparison, which would be the only accurate validation method based on auscultation. Two main alternative methods are provided by current standards, that is, two-arm simultaneous comparison (method 1) and one-arm sequential comparison (method 2); however, the accuracy of these validation methods might not be sufficient to compensate for the suspicious accuracy in lateral blood pressure (BP) differences (LD) and/or BP variations (BPV) between the device and reference readings. Thus, the Japan ISO-WG for sphygmomanometer standards has been studying a new method that might improve validation accuracy (method 3). The purpose of this study is to determine the appropriateness of method 3 by comparing immunity to LD and BPV with those of the current validation methods (methods 1 and 2). The validation accuracy of the above three methods was assessed in human participants [N=120, 45+/-15.3 years (mean+/-SD)]. An oscillometric automated monitor, Omron HEM-762, was used as the tested device. When compared with the others, methods 1 and 3 showed a smaller intra-individual standard deviation of device error (SD1), suggesting their higher reproducibility of validation. The SD1 by method 2 (P=0.004) significantly correlated with the participant's BP, supporting our hypothesis that the increased SD of device error by method 2 is at least partially caused by essential BPV. Method 3 showed a significantly (P=0.0044) smaller interparticipant SD of device error (SD2), suggesting its higher interparticipant consistency of validation. Among the methods of validation of the clinical accuracy of auto-BPMs, method 3, which showed the highest reproducibility and highest interparticipant consistency, can be proposed as being the most appropriate.

Qualitative methods in radiography research: a proposed framework

International Nuclear Information System (INIS)

Adams, J.; Smith, T.

2003-01-01

Introduction: While radiography is currently developing a research base, which is important in terms of professional development and informing practice and policy issues in the field, the amount of research published by radiographers remains limited. However, a range of qualitative methods offer further opportunities for radiography research. Purpose: This paper briefly introduces a number of key qualitative methods (qualitative interviews, focus groups, observational methods, diary methods and document/text analysis) and sketches one possible framework for future qualitative work in radiography research. The framework focuses upon three areas for study: intra-professional issues; inter-professional issues; and clinical practice, patient and health delivery issues. While the paper outlines broad areas for future focus rather than providing a detailed protocol for how individual pieces of research should be conducted, a few research questions have been chosen and examples of possible qualitative methods required to answer such questions are outlined for each area. Conclusion: Given the challenges and opportunities currently facing the development of a research base within radiography, the outline of key qualitative methods and broad areas suitable for their application is offered as a useful tool for those within the profession looking to embark upon or enhance their research career

Dynamic Response of Dam-Reservoir Systems: Review and a Semi-Analytical Proposal

Directory of Open Access Journals (Sweden)

Paulo Marcelo Vieira Ribeiro

Full Text Available Abstract This paper presents a review of current techniques employed for dynamic analysis of concrete gravity dams under seismic action. Traditional procedures applied in design bureaus, such as the Pseudo-Static method, often neglect structural dynamic properties, as well as ground amplification effects. A practical alternative arises with the Pseudo-Dynamic method, which considers a simplified spectrum response in the fundamental mode. The authors propose a self-contained development and detailed examples of this latter method, including a comparison with finite element models using transient response of fluid-structure systems. It is verified that application of the traditional procedure should be done carefully and limited to extremely rigid dams. On the other hand, the proposed development is straightforward and in agreement with finite element results for general cases where dam flexibility plays an important role.

Improved Object Proposals with Geometrical Features for Autonomous Driving

Directory of Open Access Journals (Sweden)

Yiliu Feng

2017-01-01

Full Text Available This paper aims at generating high-quality object proposals for object detection in autonomous driving. Most existing proposal generation methods are designed for the general object detection, which may not perform well in a particular scene. We propose several geometrical features suited for autonomous driving and integrate them into state-of-the-art general proposal generation methods. In particular, we formulate the integration as a feature fusion problem by fusing the geometrical features with existing proposal generation methods in a Bayesian framework. Experiments on the challenging KITTI benchmark demonstrate that our approach improves the existing methods significantly. Combined with a convolutional neural net detector, our approach achieves state-of-the-art performance on all three KITTI object classes.

A method for including external feed in depletion calculations with CRAM and implementation into ORIGEN

International Nuclear Information System (INIS)

Isotalo, A.E.; Wieselquist, W.A.

2015-01-01

Highlights: • A method for handling external feed in depletion calculations with CRAM. • Source term can have polynomial or exponentially decaying time-dependence. • CRAM with source term and adjoint capability implemented to ORIGEN in SCALE. • The new solver is faster and more accurate than the original solver of ORIGEN. - Abstract: A method for including external feed with polynomial time dependence in depletion calculations with the Chebyshev Rational Approximation Method (CRAM) is presented and the implementation of CRAM to the ORIGEN module of the SCALE suite is described. In addition to being able to handle time-dependent feed rates, the new solver also adds the capability to perform adjoint calculations. Results obtained with the new CRAM solver and the original depletion solver of ORIGEN are compared to high precision reference calculations, which shows the new solver to be orders of magnitude more accurate. Furthermore, in most cases, the new solver is up to several times faster due to not requiring similar substepping as the original one

Self-mixing laser diode included in scanning microwave microscope to the control of probe nanodisplacement

Science.gov (United States)

Usanov, D. A.; Skripal, A. V.; Astakhov, E. I.; Dobdin, S. Y.

2018-04-01

The possibilities of self-mixing interferometry for measuring nanodisplacement of a probe included in a near-field scanning microwave microscope have been considered. The features of the formation of a laser interference signal at current modulation of the wavelength of laser radiation have been investigated. Experimental responses of a semiconductor laser system included in scanning microwave microscope to control nanodisplacement of the probe have been demonstrated.To register the nanodisplacement of the probe, it is proposed to use the method of determining the stationary phase of a laser interference signal by low-frequency spectrum of a semiconductor laser. The change of the amplitudes of the spectral components in the spectrum of the interference signal due to creation of the standing wave in the external resonator of the laser self-mixing system has been shown. The form of the interference signal at current modulation of the radiation wavelength was experimentally obtained when the probe moves with a step of 80 nm. The results of measuring nanodisplacements of an electromagnetic translator STANDA 8MVT40-13 have been demonstrated. Deviation of the nanodisplacement of the proposed method does not exceed 15%.

Composite material including nanocrystals and methods of making

Science.gov (United States)

Bawendi, Moungi G.; Sundar, Vikram C.

2010-04-06

Temperature-sensing compositions can include an inorganic material, such as a semiconductor nanocrystal. The nanocrystal can be a dependable and accurate indicator of temperature. The intensity of emission of the nanocrystal varies with temperature and can be highly sensitive to surface temperature. The nanocrystals can be processed with a binder to form a matrix, which can be varied by altering the chemical nature of the surface of the nanocrystal. A nanocrystal with a compatibilizing outer layer can be incorporated into a coating formulation and retain its temperature sensitive emissive properties.

Including mixed methods research in systematic reviews: Examples from qualitative syntheses in TB and malaria control

Science.gov (United States)

2012-01-01

Background Health policy makers now have access to a greater number and variety of systematic reviews to inform different stages in the policy making process, including reviews of qualitative research. The inclusion of mixed methods studies in systematic reviews is increasing, but these studies pose particular challenges to methods of review. This article examines the quality of the reporting of mixed methods and qualitative-only studies. Methods We used two completed systematic reviews to generate a sample of qualitative studies and mixed method studies in order to make an assessment of how the quality of reporting and rigor of qualitative-only studies compares with that of mixed-methods studies. Results Overall, the reporting of qualitative studies in our sample was consistently better when compared with the reporting of mixed methods studies. We found that mixed methods studies are less likely to provide a description of the research conduct or qualitative data analysis procedures and less likely to be judged credible or provide rich data and thick description compared with standalone qualitative studies. Our time-related analysis shows that for both types of study, papers published since 2003 are more likely to report on the study context, describe analysis procedures, and be judged credible and provide rich data. However, the reporting of other aspects of research conduct (i.e. descriptions of the research question, the sampling strategy, and data collection methods) in mixed methods studies does not appear to have improved over time. Conclusions Mixed methods research makes an important contribution to health research in general, and could make a more substantial contribution to systematic reviews. Through our careful analysis of the quality of reporting of mixed methods and qualitative-only research, we have identified areas that deserve more attention in the conduct and reporting of mixed methods research. PMID:22545681

Optimal Control as a method for Diesel engine efficiency assessment including pressure and NO_x constraints

International Nuclear Information System (INIS)

Guardiola, Carlos; Climent, Héctor; Pla, Benjamín; Reig, Alberto

2017-01-01

Highlights: • Optimal Control is applied for heat release shaping in internal combustion engines. • Optimal Control allows to assess the engine performance with a realistic reference. • The proposed method gives a target heat release law to define control strategies. - Abstract: The present paper studies the optimal heat release law in a Diesel engine to maximise the indicated efficiency subject to different constraints, namely: maximum cylinder pressure, maximum cylinder pressure derivative, and NO_x emission restrictions. With this objective, a simple but also representative model of the combustion process has been implemented. The model consists of a 0D energy balance model aimed to provide the pressure and temperature evolutions in the high pressure loop of the engine thermodynamic cycle from the gas conditions at the intake valve closing and the heat release law. The gas pressure and temperature evolutions allow to compute the engine efficiency and NO_x emissions. The comparison between model and experimental results shows that despite the model simplicity, it is able to reproduce the engine efficiency and NO_x emissions. After the model identification and validation, the optimal control problem is posed and solved by means of Dynamic Programming (DP). Also, if only pressure constraints are considered, the paper proposes a solution that reduces the computation cost of the DP strategy in two orders of magnitude for the case being analysed. The solution provides a target heat release law to define injection strategies but also a more realistic maximum efficiency boundary than the ideal thermodynamic cycles usually employed to estimate the maximum engine efficiency.

Proposed Hydro-Quebec development plan, 1993: Proposal

International Nuclear Information System (INIS)

1992-01-01

The Quebec government now requires Hydro-Quebec to submit a development plan every three years instead of annually, in order to permit more in-depth studies and a broader consultation with interested parties. In the first of such three-year plans, a series of plan proposals is presented which was developed after a year of consultation with various groups on four fundamental matters: energy efficiency, means of generation, electro-intensive industries, and electricity exports. Options for meeting future demand at Hydro-Quebec are assessed, including the construction of new generation and transmission facilities, rehabilitation of existing facilities, improving electrical energy efficiency, and conservation strategies. These options are considered while applying the principle of sustainable development that respects the environment. Hydroelectricity will continue to be emphasized as the main source of generation since hydroelectric facilities offer distinct advantages in terms of costs, environmental impacts, and economic spinoffs. The proposed plan also presents objectives and strategies for improving the quality of service and internal operations. Financial forecasts for Hydro-Quebec are proposed which take into account the forecast changes in the utility's cost and revenue factors and its self-financing requirements. 5 figs., 15 tabs

A proposed Regulatory Guide basis for spent fuel decay heat

International Nuclear Information System (INIS)

Hermann, O.W.; Parks, C.V.; Renier, J.P.

1991-01-01

A proposed revision to Regulatory Guide 3.54, ''Spent Fuel Heat Generation in an Independent Spent Fuel Storage Installation'' has been developed for the US Nuclear Regulatory Commission. The proposed revision includes a data base of decay heat rates calculated as a function of burnup, specific power, cooling time, initial fuel 235 U enrichment and assembly type (i.e., PWR or BWR). Validation of the calculational method was done by comparison with existing measured decay heat rates. Procedures for proper use of the data base, adjustment formulae accounting for effects due to differences in operating history and initial enrichment, and a defensible safety factor were derived. 15 refs., 6 tabs

[Proposal of a conceptual method of supportive care for co-active patients].

Science.gov (United States)

Abidli, Yamine; Piette, Danielle; Casini, Annalisa

2015-01-01

There is a broad consensus on the importance for health professionals to support co-active patients. However, in practice, very few "patient care partnership" approaches have been developed. We hypothesized that the lack of investment in supporting patient care partnerships is due to the lack of interest in the skills needed by caregivers to provide such support. This paper intends to address thisgap. The patient care partnership method is studied, adapted and developed from existing models. It complements, harmonizes and integrates various schools of thought arising from the need to place the patient at the center of care and life in general. The patient care partnership method includes 7 stages during which the professional accompanies the patient through the process of care. The methodological approach for training professionals is designed to ensure that professionals experience the change as well as its difficulties of the change they expect from the patient in the care relationship. This method now needs to be validated by the experience of other professionals in order define the limits of application and to allow further development.

Settlement behavior of the container for high-level nuclear waste disposal. Centrifuge model tests and proposal for simple evaluation method for settlement behavior

International Nuclear Information System (INIS)

Nakamura, Kunihiko; Tanaka, Yukihisa

2004-01-01

In Japan, bentonite will be used as buffer materials in high-level nuclear waste disposal. In the softened buffer material with the infiltration of various properties of under ground water, if the container deeply sinks, the decrease of the thickness of the buffer materials may lose the required abilities. Therefore, it is very important to consider settlement of container. In this study, influences of distilled water and artificial seawater on the settlement of the container were investigated and a simple evaluation method for settlement of the container was proposed. The following findings were obtained from this study. (1) Under the distilled water, amount of settlement decreases exponentially as dry density becomes larger. (2) While the amount of settlement of container under the 10% artificial seawater was almost equal to the one in the distilled water, the container was floating under the 100% artificial seawater. (3) The simple evaluation method for settlement of container was proposed based on the diffuse double layer theory, and the effectiveness of the proposed method was demonstrated by the results of several experiments. (author)

A "conservative" method of thoracic wall dissection: a proposal for teaching human anatomy.

Science.gov (United States)

Barberini, Fabrizio; Brunone, Francesca

2008-01-01

The common methods of dissection exposing the thoracic organs include crossing of the wall together with wide resection of its muscular planes. In order to preserve these structures, a little demolishing technique of the thoracic wall is proposed, entering the thoracic cavity without extensive resection of the pectoral muscles. This method is based on the fact that these muscles rise up from the wall, like a bridge connecting the costal plane with the upper limb, and that the pectoralis major shows a segmental constitution. SUPERIOR LIMIT: Resect the sternal manubrium transversely between the 1st and the 2nd rib. The incision is prolonged along the 1st intercostal space, separating the first sterno-costal segment of the pectoralis major from the second one, and involving the intercostal muscles as far as the medial margin of the pectoralis minor. This muscle must be raised up, and the transverse resection continued below its medial margin latero-medially along the 1st intercostal space, to rejoin the cut performed before. Then, the incision of the 1st intercostal space is prolonged below the lateral margin of the pectoralis minor, which must be kept raised up, medio-laterally as far as the anterior axillary line. INFERIOR LIMIT: It corresponds to the inferior border of the thoracic cage, resected from the xiphoid process to the anterior axillary line, together with the sterno-costal insertions of the diaphragm. Then, an incision of the sterno-pericardial ligaments and a median sternotomy from the xiphoid process to the transverse resection of the manubrium should be performed. LATERAL LIMIT: From the point of crossing of the anterior axillary line with the inferior limit, resect the ribs from the 10th to the 2nd one. The lateral part of the pectoralis major must be raised up, so that the costal resection may be continued below it. Then, at the lateral extremity of the superior incision, the first and the second sternocostal segment of the pectoralis major must be

Including mixed methods research in systematic reviews: examples from qualitative syntheses in TB and malaria control.

Science.gov (United States)

Atkins, Salla; Launiala, Annika; Kagaha, Alexander; Smith, Helen

2012-04-30

Health policy makers now have access to a greater number and variety of systematic reviews to inform different stages in the policy making process, including reviews of qualitative research. The inclusion of mixed methods studies in systematic reviews is increasing, but these studies pose particular challenges to methods of review. This article examines the quality of the reporting of mixed methods and qualitative-only studies. We used two completed systematic reviews to generate a sample of qualitative studies and mixed method studies in order to make an assessment of how the quality of reporting and rigor of qualitative-only studies compares with that of mixed-methods studies. Overall, the reporting of qualitative studies in our sample was consistently better when compared with the reporting of mixed methods studies. We found that mixed methods studies are less likely to provide a description of the research conduct or qualitative data analysis procedures and less likely to be judged credible or provide rich data and thick description compared with standalone qualitative studies. Our time-related analysis shows that for both types of study, papers published since 2003 are more likely to report on the study context, describe analysis procedures, and be judged credible and provide rich data. However, the reporting of other aspects of research conduct (i.e. descriptions of the research question, the sampling strategy, and data collection methods) in mixed methods studies does not appear to have improved over time. Mixed methods research makes an important contribution to health research in general, and could make a more substantial contribution to systematic reviews. Through our careful analysis of the quality of reporting of mixed methods and qualitative-only research, we have identified areas that deserve more attention in the conduct and reporting of mixed methods research.

Proposed Suitable Methods to Detect Transient Regime Switching to Improve Power Quality with Wavelet Transform

Directory of Open Access Journals (Sweden)

Javad Safaee Kuchaksaraee

2016-10-01

Full Text Available The increasing consumption of electrical energy and the use of non-linear loads that create transient regime states in distribution networks is increasing day by day. This is the only reason due to which the analysis of power quality for energy sustainability in power networks has become more important. Transients are often created by energy injection through switching or lightning and make changes in voltage and nominal current. Sudden increase or decrease in voltage or current makes characteristics of the transient regime. This paper shed some lights on the capacitor bank switching, which is one of the main causes for oscillatory transient regime states in the distribution network, using wavelet transform. The identification of the switching current of capacitor bank and the internal fault current of the transformer to prevent the unnecessary outage of the differential relay, it propose a new smart method. The accurate performance of this method is shown by simulation in EMTP and MATLAB (matrix laboratory software.

Feasibility study and technical proposal for the use of microseismic methods in the long-term observation of bedrock stability

International Nuclear Information System (INIS)

Saari, J.

1995-04-01

Recent geodetic and seismological studies have paid attention to the slow deformation occurring in the Fennoscandian Shield. On the basis of these studies, together with in-situ stress measurements, the idea has been put forth that horizontal movement can be even greater than vertical movement. Local seismotectonics has importance in relation to the predictions of the long-term stability of the bedrock at the final disposal site. Potential direct and - what in Finland is more likely - indirect effects on the vault are due to local earthquakes of creep. The direct effects on the repository include rock vibration and displacement on an increasing fault. The indirect effects are changes in the surrounding structure, in the stress field, in the groundwater table, pressure, flux and chemistry. The block movements are controlled mainly by the network of fracture zones. The report deals with the possibilities to monitor by seismic methods slow movements occurring in the bedrock at the local level. The report includes descriptions of instrumentation for recording microearthquakes, the seismic network and an interpretation of the observations. The potential sites for disposal (Kuhmo, Aeaenekoski, Eurajoki) are compared in relation to seismic monitoring. Also the experiences of other investigations and a proposal for microearthquake investigations as well as of prospective developments within monitoring are presented. (28 refs., 17 figs.)

Facade Proposals for Urban Augmented Reality

OpenAIRE

Fond , Antoine; Berger , Marie-Odile; Simon , Gilles

2017-01-01

International audience; We introduce a novel object proposals method specific to building facades. We define new image cues that measure typical facadecharacteristics such as semantic, symmetry and repetitions. They are combined to generate a few facade candidates in urban environments fast. We show that our method outperforms state-of-the-art object proposals techniques for this task on the 1000 images of the Zurich Building Database. We demonstrate the interest of this procedure for augment...

Developing an Agent-Based Simulation System for Post-Earthquake Operations in Uncertainty Conditions: A Proposed Method for Collaboration among Agents

Directory of Open Access Journals (Sweden)

Navid Hooshangi

2018-01-01

Full Text Available Agent-based modeling is a promising approach for developing simulation tools for natural hazards in different areas, such as during urban search and rescue (USAR operations. The present study aimed to develop a dynamic agent-based simulation model in post-earthquake USAR operations using geospatial information system and multi agent systems (GIS and MASs, respectively. We also propose an approach for dynamic task allocation and establishing collaboration among agents based on contract net protocol (CNP and interval-based Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS methods, which consider uncertainty in natural hazards information during agents’ decision-making. The decision-making weights were calculated by analytic hierarchy process (AHP. In order to implement the system, earthquake environment was simulated and the damage of the buildings and a number of injuries were calculated in Tehran’s District 3: 23%, 37%, 24% and 16% of buildings were in slight, moderate, extensive and completely vulnerable classes, respectively. The number of injured persons was calculated to be 17,238. Numerical results in 27 scenarios showed that the proposed method is more accurate than the CNP method in the terms of USAR operational time (at least 13% decrease and the number of human fatalities (at least 9% decrease. In interval uncertainty analysis of our proposed simulated system, the lower and upper bounds of uncertain responses are evaluated. The overall results showed that considering uncertainty in task allocation can be a highly advantageous in the disaster environment. Such systems can be used to manage and prepare for natural hazards.

A proposal for performing software safety hazard analysis

International Nuclear Information System (INIS)

Lawrence, J.D.; Gallagher, J.M.

1997-01-01

Techniques for analyzing the safety and reliability of analog-based electronic protection systems that serve to mitigate hazards in process control systems have been developed over many years, and are reasonably understood. An example is the protection system in a nuclear power plant. The extension of these techniques to systems which include digital computers is not well developed, and there is little consensus among software engineering experts and safety experts on how to analyze such systems. One possible technique is to extend hazard analysis to include digital computer-based systems. Software is frequently overlooked during system hazard analyses, but this is unacceptable when the software is in control of a potentially hazardous operation. In such cases, hazard analysis should be extended to fully cover the software. A method for performing software hazard analysis is proposed in this paper. The method concentrates on finding hazards during the early stages of the software life cycle, using an extension of HAZOP

Measure Guideline: Summary of Interior Ducts in New Construction, Including an Efficient, Affordable Method to Install Fur-Down Interior Ducts

Energy Technology Data Exchange (ETDEWEB)

Beal, D. [BA-PIRC, Cocoa, FL (United States); McIlvaine, J. [BA-PIRC, Cocoa, FL (United States); Fonorow, K. [BA-PIRC, Cocoa, FL (United States); Martin, E. [BA-PIRC, Cocoa, FL (United States)

2011-11-01

This document illustrates guidelines for the efficient installation of interior duct systems in new housing, including the fur-up chase method, the fur-down chase method, and interior ducts positioned in sealed attics or sealed crawl spaces.

Proposed method for assigning metric tons of heavy metal values to defense high-level waste forms to be disposed of in a geologic repository

International Nuclear Information System (INIS)

1987-08-01

A proposed method is described for assigning an equivalent metric ton heavy metal (eMTHM) value to defense high-level waste forms to be disposed of in a geologic repository. This method for establishing a curie equivalency between defense high-level waste and irradiated commercial fuel is based on the ratio of defense fuel exposure to the typical commercial fuel exposure, MWd/MTHM. application of this technique to defense high-level wastes is described. Additionally, this proposed technique is compared to several alternate calculations for eMTHM. 15 refs., 2 figs., 10 tabs

Proposal for evaluation methodology on impact resistant performance and construction method of tornado missile protection net structure

International Nuclear Information System (INIS)

Namba, Kosuke; Shirai, Koji

2014-01-01

In nuclear power plants, the necessity of the Tornado Missile Protection Structure is becoming a technical key issue. Utilization of the net structure seems to be one of the realistic counter measures from the point of the view of the mitigation wind and seismic loads. However, the methodology for the selection of the net suitable materials, the energy absorption design method and the construction method are not sufficiently established. In this report, three materials (high-strength metal mesh, super strong polyethylene fiber net and steel grating) were selected for the candidate material and the material screening tests, the energy absorption tests by free drop test using the heavy weight and the impact tests with the small diameter missile. As a result, high-strength metal mesh was selected as a suitable material for tornado missile protection net structure. Moreover, the construction method to obtain the good energy absorption performance of the material and the practical design method to estimate the energy absorption of the high-strength metal mesh under tornado missile impact load were proposed. (author)

Teaching Methods in Biology Education and Sustainability Education Including Outdoor Education for Promoting Sustainability--A Literature Review

Science.gov (United States)

Jeronen, Eila; Palmberg, Irmeli; Yli-Panula, Eija

2017-01-01

There are very few studies concerning the importance of teaching methods in biology education and environmental education including outdoor education for promoting sustainability at the levels of primary and secondary schools and pre-service teacher education. The material was selected using special keywords from biology and sustainable education…

[Classification of local anesthesia methods].

Science.gov (United States)

Petricas, A Zh; Medvedev, D V; Olkhovskaya, E B

The traditional classification methods of dental local anesthesia must be modified. In this paper we proved that the vascular mechanism is leading component of spongy injection. It is necessary to take into account the high effectiveness and relative safety of spongy anesthesia, as well as versatility, ease of implementation and the growing prevalence in the world. The essence of the proposed modification is to distinguish the methods in diffusive (including surface anesthesia, infiltration and conductive anesthesia) and vascular-diffusive (including intraosseous, intraligamentary, intraseptal and intrapulpal anesthesia). For the last four methods the common term «spongy (intraosseous) anesthesia» may be used.

A proposed through-flow inverse method for the design of mixed-flow pumps

Science.gov (United States)

Borges, Joao Eduardo

1991-01-01

A through-flow (hub-to-shroud) truly inverse method is proposed and described. It uses an imposition of mean swirl, i.e., radius times mean tangential velocity, given throughout the meridional section of the turbomachine as an initial design specification. In the present implementation, it is assumed that the fluid is inviscid, incompressible, and irrotational at inlet and that the blades are supposed to have zero thickness. Only blade rows that impart to the fluid a constant work along the space are considered. An application of this procedure to design the rotor of a mixed-flow pump is described in detail. The strategy used to find a suitable mean swirl distribution and the other design inputs is also described. The final blade shape and pressure distributions on the blade surface are presented, showing that it is possible to obtain feasible designs using this technique. Another advantage of this technique is the fact that it does not require large amounts of CPU time.

24 CFR 941.606 - Proposal.

Science.gov (United States)

2010-04-01

...) Life cycle analysis. For new construction and substantial rehabilitation, the criteria to be used in equipping the proposed development with heating and cooling systems, which shall include a life-cycle cost... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Proposal. 941.606 Section 941.606...

Binge eating disorder should be included in DSM-IV: a reply to Fairburn et al.'s "the classification of recurrent overeating: the binge eating disorder proposal".

Science.gov (United States)

Spitzer, R L; Stunkard, A; Yanovski, S; Marcus, M D; Wadden, T; Wing, R; Mitchell, J; Hasin, D

1993-03-01

Extensive recent research supports a proposal that a new eating disorder, binge eating disorder (BED), be included in DSM-IV. BED criteria define a relatively pure group of individuals who are distressed by recurrent binge eating who do not exhibit the compensatory features of bulimia nervosa. This large number of patients currently can only be diagnosed as eating disorder not otherwise specified (EDNOS). Recognizing this new disorder will help stimulate research and clinical programs for these patients. Fairburn et al.'s critique of BED fails to acknowledge the large body of knowledge that indicates that BED represents a distinct and definable subgroup of eating disordered patients and that the diagnosis provides useful information about psychopathology, prognosis, and outcome (Fairburn, Welch, & Hay [in press]. The classification of recurrent overeating: The "binge eating disorder" proposal. International Journal of Eating Disorders.) Against any reasonable standard for adding a new diagnosis to DSM-IV, BED meets the test.

Full Space Vectors Modulation for Nine-Switch Converters Including CF & DF Modes

DEFF Research Database (Denmark)

Dehghan Dehnavi, Seyed Mohammad; Mohamadian, Mustafa; Andersen, Michael A. E.

2010-01-01

converter. As a space vector modulation for DF mode has already been proposed by authors. This paper proposes a full space vector modulation (SVM) for both CF and DF modes. Also practical methods are presented for SVM proposed. In addition a special SVM is proposed that offers minimum total harmonic...... distortion (THD) in DF mode. The performance of the proposed SVM is verified by simulation results....

Draft report: a selection methodology for LWR safety R and D programs and proposals

International Nuclear Information System (INIS)

Husseiny, A.A.; Ritzman, R.L.

1980-03-01

The results of work done to develop a methodology for selecting LWR safety R and D programs and proposals is described. A critical survey of relevant decision analysis methods is provided including the specifics of multiattribute utility theory. This latter method forms the basis of the developed selection methodology. Details of the methodology and its use are provided along with a sample illustration of its application

Draft report: a selection methodology for LWR safety R and D programs and proposals

Energy Technology Data Exchange (ETDEWEB)

Husseiny, A. A.; Ritzman, R. L.

1980-03-01

The results of work done to develop a methodology for selecting LWR safety R and D programs and proposals is described. A critical survey of relevant decision analysis methods is provided including the specifics of multiattribute utility theory. This latter method forms the basis of the developed selection methodology. Details of the methodology and its use are provided along with a sample illustration of its application.

Comparison of different methods to include recycling in LCAs of aluminium cans and disposable polystyrene cups.

Science.gov (United States)

van der Harst, Eugenie; Potting, José; Kroeze, Carolien

2016-02-01

Many methods have been reported and used to include recycling in life cycle assessments (LCAs). This paper evaluates six widely used methods: three substitution methods (i.e. substitution based on equal quality, a correction factor, and alternative material), allocation based on the number of recycling loops, the recycled-content method, and the equal-share method. These six methods were first compared, with an assumed hypothetical 100% recycling rate, for an aluminium can and a disposable polystyrene (PS) cup. The substitution and recycled-content method were next applied with actual rates for recycling, incineration and landfilling for both product systems in selected countries. The six methods differ in their approaches to credit recycling. The three substitution methods stimulate the recyclability of the product and assign credits for the obtained recycled material. The choice to either apply a correction factor, or to account for alternative substituted material has a considerable influence on the LCA results, and is debatable. Nevertheless, we prefer incorporating quality reduction of the recycled material by either a correction factor or an alternative substituted material over simply ignoring quality loss. The allocation-on-number-of-recycling-loops method focusses on the life expectancy of material itself, rather than on a specific separate product. The recycled-content method stimulates the use of recycled material, i.e. credits the use of recycled material in products and ignores the recyclability of the products. The equal-share method is a compromise between the substitution methods and the recycled-content method. The results for the aluminium can follow the underlying philosophies of the methods. The results for the PS cup are additionally influenced by the correction factor or credits for the alternative material accounting for the drop in PS quality, the waste treatment management (recycling rate, incineration rate, landfilling rate), and the

Proposal for an alignment method of the CLIC linear accelerator - From geodesic networks to the active pre-alignment

International Nuclear Information System (INIS)

Touze, T.

2011-01-01

The compact linear collider (CLIC) is the particle accelerator project proposed by the european organization for nuclear research (CERN) for high energy physics after the large hadron collider (LHC). Because of the nano-metric scale of the CLIC leptons beams, the emittance growth budget is very tight. It induces alignment tolerances on the positions of the CLIC components that have never been achieved before. The last step of the CLIC alignment will be done according to the beam itself. It falls within the competence of the physicists. However, in order to implement the beam-based feedback, a challenging pre-alignment is required: 10 μm at 3σ along a 200 m sliding window. For such a precision, the proposed solution must be compatible with a feedback between the measurement and repositioning systems. The CLIC pre-alignment will have to be active. This thesis does not demonstrate the feasibility of the CLIC active pre-alignment but shows the way to the last developments that have to be done for that purpose. A method is proposed. Based on the management of the Helmert transformations between Euclidean coordinate systems, from the geodetic networks to the metrological measurements, this method is likely to solve the CLIC pre-alignment problem. Large scale facilities have been built and Monte-Carlo simulations have been made in order to validate the mathematical modeling of the measurement systems and of the alignment references. When this is done, it will be possible to extrapolate the modeling to the entire CLIC length. It will be the last step towards the demonstration of the CLIC pre-alignment feasibility. (author)

Computation of Optimal Monotonicity Preserving General Linear Methods

KAUST Repository

Ketcheson, David I.

2009-07-01

Monotonicity preserving numerical methods for ordinary differential equations prevent the growth of propagated errors and preserve convex boundedness properties of the solution. We formulate the problem of finding optimal monotonicity preserving general linear methods for linear autonomous equations, and propose an efficient algorithm for its solution. This algorithm reliably finds optimal methods even among classes involving very high order accuracy and that use many steps and/or stages. The optimality of some recently proposed methods is verified, and many more efficient methods are found. We use similar algorithms to find optimal strong stability preserving linear multistep methods of both explicit and implicit type, including methods for hyperbolic PDEs that use downwind-biased operators.

Economic/Environmental power dispatch for power systems including wind farms

Directory of Open Access Journals (Sweden)

Imen BEN JAOUED

2015-05-01

Full Text Available This paper presents the problem of the Economic/Environmental power Dispatching (EED of hybrid power system including wind energies. The power flow model for a stall regulated fixed speed wind generator (SR-FSWG system is discussed to assess the steady-state condition of power systems with wind farms. Modified Newton-Raphson algorithm including SR-FSWG is used to solve the load flow equations in which the state variables of the wind generators are combined with the nodal voltage magnitudes and angles of the entire network. The EED problem is a nonlinear constrained multi-objective optimization problem, two competing fuel cost and pollutant emission objectives should be minimized simultaneously while satisfying certain system constraints. In this paper, the resolution is done by the algorithm multi-objective particle swarm optimization (MOPSO. The effectiveness of the proposed method has been verified on IEEE 6-generator 30-bus test system and using MATLAB software package.

A Systematic Method to Synthesize New Transformerless Full-bridge Grid-tied Inverters

DEFF Research Database (Denmark)

Wang, Hongliang; Burton, Sarah; Liu, Yan-Fei

2014-01-01

Many inverter topologies have been proposed to eliminate the leakage current of transformerless Full Bridge Grid-Tied photovoltaic (PV) inverters. These include implementations such as the H5, H6, and HERIC topologies, among others. In this paper, a new full bridge topology synthesis method, called...... the MN synthesis method, is proposed. The MN method introduces two criteria that can be used to synthesize all of the possible topologies, including the existing topologies as well as new simplified topologies. This method concludes that there are only 15 simplified topologies available. Most simplified...... topologies from MN method have been verified by existing papers and patents....

The qualitative research proposal

Directory of Open Access Journals (Sweden)

H Klopper

2008-09-01

Full Text Available Qualitative research in the health sciences has had to overcome many prejudices and a number of misunderstandings, but today qualitative research is as acceptable as quantitative research designs and is widely funded and published. Writing the proposal of a qualitative study, however, can be a challenging feat, due to the emergent nature of the qualitative research design and the description of the methodology as a process. Even today, many sub-standard proposals at post-graduate evaluation committees and application proposals to be considered for funding are still seen. This problem has led the researcher to develop a framework to guide the qualitative researcher in writing the proposal of a qualitative study based on the following research questions: (i What is the process of writing a qualitative research proposal? and (ii What does the structure and layout of a qualitative proposal look like? The purpose of this article is to discuss the process of writing the qualitative research proposal, as well as describe the structure and layout of a qualitative research proposal. The process of writing a qualitative research proposal is discussed with regards to the most important questions that need to be answered in your research proposal with consideration of the guidelines of being practical, being persuasive, making broader links, aiming for crystal clarity and planning before you write. While the structure of the qualitative research proposal is discussed with regards to the key sections of the proposal, namely the cover page, abstract, introduction, review of the literature, research problem and research questions, research purpose and objectives, research paradigm, research design, research method, ethical considerations, dissemination plan, budget and appendices.

Proposal of quality indicators for cardiac rehabilitation after acute coronary syndrome in Japan: a modified Delphi method and practice test.

Science.gov (United States)

Ohtera, Shosuke; Kanazawa, Natsuko; Ozasa, Neiko; Ueshima, Kenji; Nakayama, Takeo

2017-01-27

Cardiac rehabilitation is underused and its quality in practice is unclear. A quality indicator is a measurable element of clinical practice performance. This study aimed to propose a set of quality indicators for cardiac rehabilitation following an acute coronary event in the Japanese population and conduct a small-size practice test to confirm feasibility and applicability of the indicators in real-world clinical practice. This study used a modified Delphi technique (the RAND/UCLA appropriateness method), a consensus method which involves an evidence review, a face-to-face multidisciplinary panel meeting and repeated anonymous rating. Evidence to be reviewed included clinical practice guidelines available in English or Japanese and existing quality indicators. Performance of each indicator was assessed retrospectively using medical records at a university hospital in Japan. 10 professionals in cardiac rehabilitation for the consensus panel. In the literature review, 23 clinical practice guidelines and 16 existing indicators were identified to generate potential indicators. Through the consensus-building process, a total of 30 indicators were assessed and finally 13 indicators were accepted. The practice test (n=39) revealed that 74% of patients underwent cardiac rehabilitation. Median performance of process measures was 93% (IQR 46-100%). 'Communication with the doctor who referred the patient to cardiac rehabilitation' and 'continuous participation in cardiac rehabilitation' had low performance (32% and 38%, respectively). A modified Delphi technique identified a comprehensive set of quality indicators for cardiac rehabilitation. The single-site, small-size practice test confirmed that most of the proposed indicators were measurable in real-world clinical practice. However, some clinical processes which are not covered by national health insurance in Japan had low performance. Further studies will be needed to clarify and improve the quality of care in cardiac

Asynchronous decentralized method for interconnected electricity markets

International Nuclear Information System (INIS)

Huang, Anni; Joo, Sung-Kwan; Song, Kyung-Bin; Kim, Jin-Ho; Lee, Kisung

2008-01-01

This paper presents an asynchronous decentralized method to solve the optimization problem of interconnected electricity markets. The proposed method decomposes the optimization problem of combined electricity markets into individual optimization problems. The impact of neighboring markets' information is included in the objective function of the individual market optimization problem by the standard Lagrangian relaxation method. Most decentralized optimization methods use synchronous models of communication to exchange updated market information among markets during the iterative process. In this paper, however, the solutions of the individual optimization problems are coordinated through an asynchronous communication model until they converge to the global optimal solution of combined markets. Numerical examples are presented to demonstrate the advantages of the proposed asynchronous method over the existing synchronous methods. (author)

Studies and Proposals for an Automatic Crystal Control System

CERN Document Server

Drobychev, Gleb; Khruschinsky, A A; Korzhik, Mikhail; Missevitch, Oleg; Oriboni, André; Peigneux, Jean-Pierre; Schneegans, Marc

1997-01-01

This document presents the status of the studies for an Automatic Crystal Control System ( ACCOS) performed since autumn 1995 for the CMS collaboration. Evaluation of a startstop method for light yield, light uniformity and decay time measurements of PbWO4 crystals is presented, as well as the first results obtained with a compact double-beam spectrophotometer for transverse transmission. Various overall schemes are proposed for an integrated set-up including crystal dimension measurement. The initial financial evaluationperformed is also given.

Current treatments in Parkinson's including the proposal of an innovative dopamine microimplant

Directory of Open Access Journals (Sweden)

M. Velázquez-Paniagua

2016-04-01

Full Text Available Parkinson's disease is a chronic, debilitating, progressive neurological disorder of multifactorial origin. It affects between 0.3% and 2% of the over-65 population worldwide, with a predilection for men, and is characterised by bradykinesia, muscular rigidity, resting tremor and postural instability. Parkinson's is caused by decreased dopamine levels due to the loss of dopaminergic neurons in the substantia nigra. Because dopamine is a highly oxidisable molecule, precursors such as levodopa, together with catechol-O-methyltransferase and monoamine oxidase inhibitors to prevent degradation, are used in the treatment of this disease. These therapies, however, are not without their adverse effects. Surgical treatments for Parkinson's include pallidotomy, therapy deep brain stimulation, and stem cells. A more recent development involves a titanium dioxide micro-implant containing nanopores that stabilise the dopamine for continuous release. When inserted into the caudate nucleus, this micro-implant was found to counteract 85% of symptoms in hemiparkinsonian rats, and is a promising therapy for patients with Parkinson's disease.

Systematic review of proposed definitions of nocturnal polyuria and population-based evidence of their diagnostic accuracy.

Science.gov (United States)

Olesen, Tine Kold; Denys, Marie-Astrid; Vande Walle, Johan; Everaert, Karel

2018-02-06

Background Evidence of diagnostic accuracy for proposed definitions of nocturnal polyuria is currently unclear. Purpose Systematic review to determine population-based evidence of the diagnostic accuracy of proposed definitions of nocturnal polyuria based on data from frequency-volume charts. Methods Seventeen pre-specified search terms identified 351 unique investigations published from 1990 to 2016 in BIOSIS, Embase, Embase Alerts, International Pharmaceutical Abstract, Medline, and Cochrane. Thirteen original communications were included in this review based on pre-specified exclusion criteria. Data were extracted from each paper regarding subject age, sex, ethnicity, health status, sample size, data collection methods, and diagnostic discrimination of proposed definitions including sensitivity, specificity, positive and negative predictive value. Results The sample size of study cohorts, participant age, sex, ethnicity, and health status varied considerably in 13 studies reporting on the diagnostic performance of seven different definitions of nocturnal polyuria using frequency-volume chart data from 4968 participants. Most study cohorts were small, mono-ethnic, including only Caucasian males aged 50 or higher with primary or secondary polyuria that were compared to a control group of healthy men without nocturia in prospective or retrospective settings. Proposed definitions had poor discriminatory accuracy in evaluations based on data from subjects independent from the original study cohorts with findings being similar regarding the most widely evaluated definition endorsed by ICS. Conclusions Diagnostic performance characteristics for proposed definitions of nocturnal polyuria show poor to modest discrimination and are not based on sufficient level of evidence from representative, multi-ethnic population-based data from both females and males of all adult ages.

Methods of bone marrow dose calculation

International Nuclear Information System (INIS)

Taboaco, R.C.

1982-02-01

Several methods of bone marrow dose calculation for photon irradiation were analised. After a critical analysis, the author proposes the adoption, by the Instituto de Radioprotecao e Dosimetria/CNEN, of Rosenstein's method for dose calculations in Radiodiagnostic examinations and Kramer's method in case of occupational irradiation. It was verified by Eckerman and Simpson that for monoenergetic gamma emitters uniformly distributed within the bone mineral of the skeleton the dose in the bone surface can be several times higher than dose in skeleton. In this way, is also proposed the Calculation of tissue-air ratios for bone surfaces in some irradiation geometries and photon energies to be included in the Rosenstein's method for organ dose calculation in Radiodiagnostic examinations. (Author) [pt

Zirconium-based alloys, nuclear fuel rods and nuclear reactors including such alloys, and related methods

Science.gov (United States)

Mariani, Robert Dominick

2014-09-09

Zirconium-based metal alloy compositions comprise zirconium, a first additive in which the permeability of hydrogen decreases with increasing temperatures at least over a temperature range extending from 350.degree. C. to 750.degree. C., and a second additive having a solubility in zirconium over the temperature range extending from 350.degree. C. to 750.degree. C. At least one of a solubility of the first additive in the second additive over the temperature range extending from 350.degree. C. to 750.degree. C. and a solubility of the second additive in the first additive over the temperature range extending from 350.degree. C. to 750.degree. C. is higher than the solubility of the second additive in zirconium over the temperature range extending from 350.degree. C. to 750.degree. C. Nuclear fuel rods include a cladding material comprising such metal alloy compositions, and nuclear reactors include such fuel rods. Methods are used to fabricate such zirconium-based metal alloy compositions.

Testing the Construct Validity of Proposed Criteria for "DSM-5" Autism Spectrum Disorder

Science.gov (United States)

Mandy, William P. L.; Charman, Tony; Skuse, David H.

2012-01-01

Objective: To use confirmatory factor analysis to test the construct validity of the proposed "DSM-5" symptom model of autism spectrum disorder (ASD), in comparison to alternative models, including that described in "DSM-IV-TR." Method: Participants were 708 verbal children and young persons (mean age, 9.5 years) with mild to severe autistic…

Methods of evaluating market transformation programmes: experience in Sweden

International Nuclear Information System (INIS)

Neij, L.

2001-01-01

The evaluation of market transformation programmes requires the development of new methods, relative to methods used for the evaluation of traditional energy efficiency programmes. In this paper, a model for the evaluation of market transformation programmes is proposed, based in part on evaluation methods discussed in the literature. The proposed model entails an extensive evaluation process, including the evaluation of market transformation effects, the impact of these effects, and the evaluation of the outline of the programme. Furthermore, evaluations of Swedish market transformation programmes have been analysed in relation to the proposed model. The analysis shows that not all of the evaluations have been focused on market transformation, and those that have, are only partly consistent with the evaluation model proposed here. It is concluded that future evaluations of Swedish market transformation programmes should be extended and improved in accordance with the proposed model. (author)

Comparison of dietary fiber methods for foods.

Science.gov (United States)

Heckman, M M; Lane, S A

1981-11-01

In order to evaluate several proposed dietary fiber methods, 12 food samples, representing different food classes, were analyzed by (1) neutral and acid detergent fiber methods (NDF, ADF); (2) NDF with enzyme modification (ENDF); (3) a 2-fraction enzyme method for soluble, insoluble, and total dietary fiber, proposed by Furda (SDF, IDF, TDF); (+) a 1-fraction enzyme method for total dietary fiber proposed by Hellendoorn (TDF). Foods included cereals, fruits, vegetables, pectin, locust bean gum, and soybean polysaccharides. Results show that TDF by Furda and Hellendoorn methods agree reasonably well with literature values by the Southgate method, but ENDF is consistently lower; that ENDF and IDF (Furda method) agree reasonably well; that except for corn corn bran fiber (insoluble) and pectin and locus bean fiber (soluble), all materials have significant fractions of both soluble and insoluble fiber. The Furda method was used on numerous food and ingredient samples and was found to be practical and informative and to have acceptable precision (RSD values of 2.65-7.05%). It is suggested that the Furda (or similar) method be given consideration for the analysis of foods for dietary fiber.

A Proposed Method for Improving the Performance of P-Type GaAs IMPATTs

Directory of Open Access Journals (Sweden)

H. A. El-Motaafy

2012-07-01

Full Text Available A special waveform is proposed and assumed to be the optimum waveform for p-type GaAs IMPATTs. This waveform is deduced after careful and extensive study of the performance of these devices. The results presented here indicate the superiority of the performance of the IMPATTs driven by the proposed waveform over that obtained when the same IMPATTs are driven by the conventional sinusoidal waveform. These results are obtained using a full-scale computer simulation program that takes fully into account all the physical effects pertinent to IMPATT operation.  In this paper, it is indicated that the superiority of the proposed waveform is attributed to its ability to reduce the bad effects that usually degrade the IMPATT performance such as the space-charge effect and the drift-velocity dropping below saturation effect. The superiority is also attributed to the ability of the proposed waveform to improve the phase relationship between the terminal voltage and the induced current.Key Words: Computer-Aided Design, GaAs IMPATT, Microwave Engineering

Methods to establish flaw tolerances

International Nuclear Information System (INIS)

Varga, T.

1978-01-01

Three conventional methods used to establish flaw tolerances are compared with new approaches using fracture mechanics. The conventional methods are those based on (a) non-destructive testing methods; (b) fabrication and quality assurance experience; and (c) service and damage experience. Pre-requisites of fracture mechanics methods are outlined, and summaries given of linear elastic mechanics (LEFM) and elastoplastic fracture mechanics (EPFM). The latter includes discussion of C.O.D.(crack opening displacement), the J-integral and equivalent energy. Proposals are made for establishing flaw tolerances. (U.K.)

Tritium extraction methods proposed for a solid breeder blanket. Subtask WP-B 6.1 of the European Blanket Program 1996

International Nuclear Information System (INIS)

Albrecht, H.

1997-04-01

Ten different methods for the extraction of tritium from the purge gas of a ceramic blanket are described and evaluated with respect to their applicability for ITER and DEMO. The methods are based on the conditions that the purge gas is composed of helium with an addition of up to 0.1% of H 2 or O 2 and H 2 O to facilitate the release of tritium, and that tritium occurs in the purge gas in two main chemical forms, i.e. HT and HTO. Individual process steps of many methods are identical; in particular, the application of cold traps, molecular sieve beds, and diffusors are proposed in several cases. Differences between the methods arise mainly from the ways in which various process steps are combined and from the operating conditions which are chosen with respect to temperature and pressure. Up to now, none of the methods has been demonstrated to be reliably applicable for the purge gas conditions foreseen for the operation of an ITER blanket test module (or larger ceramic blanket designs such as for DEMO). These conditions are characterized by very high gas flow rates and extremely low concentrations of HT and HTO. Therefore, a proposal has been made (FZK concept) which is expected to have the best potential for applicability to ITER and DEMO and to incorporate the smallest development risk. In this concept, the extraction of tritium and excess hydrogen is accomplished by using a cold trap for freezing out HTO/H 2 O and a 5A molecular sieve bed for the adsorption of HT/H 2 . (orig.) [de

Proposals for chemical weapons during the American Civil War.

Science.gov (United States)

Hasegawa, Guy R

2008-05-01

Proposals for chemical weapons that arose during the American Civil War are described. Most incendiary and all biological agents are excluded. The described proposals appeared primarily in periodicals or letters to government officials on both sides. The weapons were usually meant to temporarily disable enemy combatants, but some might have been lethal, and Civil War caregivers were ill-prepared to deal with the weapons' effects. Evidently, none of the proposed weapons were used. In only one instance was use against civilians mentioned. Among the agents most commonly proposed were cayenne pepper or other plant-based irritants such as black pepper, snuff, mustard, and veratria. Other suggested agents included chloroform, chlorine, hydrogen cyanide, arsenic compounds, sulfur, and acids. Proponents usually suggested that the chemicals be included in explosive artillery projectiles. Less commonly proposed vehicles of delivery included fire engines, kites, and manned balloons. Some of the proposed weapons have modern counterparts.

Proposal of Environmental Impact Assessment Method for Concrete in South Korea: An Application in LCA (Life Cycle Assessment

Directory of Open Access Journals (Sweden)

Tae Hyoung Kim

2016-11-01

Full Text Available This study aims to develop a system for assessing the impact of the substances discharged from concrete production process on six environmental impact categories, i.e., global warming (GWP, acidification (AP, eutrophication (EP, abiotic depletion (ADP, ozone depletion (ODP, and photochemical oxidant creation (POCP, using the life a cycle assessment (LCA method. To achieve this, this study proposed an LCA method specifically applicable to the Korean concrete industry by adapting the ISO standards to suit the Korean situations. The proposed LCA method involves a system that performs environmental impact assessment on the basis of input information on concrete mix design, transport distance, and energy consumption in a batch plant. The Concrete Lifecycle Assessment System (CLAS thus developed provides user-friendly support for environmental impact assessment with specialized database for concrete mix materials and energy sources. In the case analysis using the CLAS, among the substances discharged from the production of 24 MPa concrete, those contributing to GWP, AP, EP, ADP, ODP, and POCP were assessed to amount to 309 kg-CO2 eq/m3, 28.7 kg-SO2 eq/m3, 5.21 kg-PO43− eq/m3, 0.000049 kg-CFC11 eq/m3, 34 kg/m3, and 21 kg-Ethylene eq/m3, respectively. Of these six environmental impact categories selected for the LCA in this study, ordinary Portland cement (OPC was found to contribute most intensely to GWP and POCP, and aggregates, to AP, EP, ODP, and ADP. It was also found that the mix design with increased prop proportion of recycled aggregate was found to contribute to reducing the impact in all other categories.

A Proposed Stochastic Finite Difference Approach Based on Homogenous Chaos Expansion

Directory of Open Access Journals (Sweden)

O. H. Galal

2013-01-01

Full Text Available This paper proposes a stochastic finite difference approach, based on homogenous chaos expansion (SFDHC. The said approach can handle time dependent nonlinear as well as linear systems with deterministic or stochastic initial and boundary conditions. In this approach, included stochastic parameters are modeled as second-order stochastic processes and are expanded using Karhunen-Loève expansion, while the response function is approximated using homogenous chaos expansion. Galerkin projection is used in converting the original stochastic partial differential equation (PDE into a set of coupled deterministic partial differential equations and then solved using finite difference method. Two well-known equations were used for efficiency validation of the method proposed. First one being the linear diffusion equation with stochastic parameter and the second is the nonlinear Burger's equation with stochastic parameter and stochastic initial and boundary conditions. In both of these examples, the probability distribution function of the response manifested close conformity to the results obtained from Monte Carlo simulation with optimized computational cost.

“Sweet Science:” A Proposal for Integral Macropolitics

Directory of Open Access Journals (Sweden)

Daniel Gustav Anderson

2010-03-01

Full Text Available This treatise proposes the practice of becoming-responsible as a basis for integral micropolitics, defined as taking active responsibility for the well-being of the totality of living beings without exception, for the sake of that well-being alone. After reviewing two extant integral models for political action and interaction, demonstrating some of the limitations inherent in them, some ways are outlined in which the characteristic features of becoming-responsible—including critical clarity, compassion, competence, and consciousness—can be expressed in the realm of public concern; first, theoretically, drawing on a model proposed by poet and artist William Blake, and second, also historically, reflecting on an experiment in radical democracy in Chile (1970-1973, such that both examples critique and advance the claims and methods of mainstream integral theory as well as the alternative approach elaborated in this essay.

New mixed finite-element methods

International Nuclear Information System (INIS)

Franca, L.P.

1987-01-01

New finite-element methods are proposed for mixed variational formulations. The methods are constructed by adding to the classical Galerkin method various least-squares like terms. The additional terms involve integrals over element interiors, and include mesh-parameter dependent coefficients. The methods are designed to enhance stability. Consistency is achieved in the sense that exact solutions identically satisfy the variational equations.Applied to several problems, simple finite-element interpolations are rendered convergent, including convenient equal-order interpolations generally unstable within the Galerkin approach. The methods are subdivided into two classes according to the manner in which stability is attained: (1) circumventing Babuska-Brezzi condition methods; (2) satisfying Babuska-Brezzi condition methods. Convergence is established for each class of methods. Applications of the first class of methods to Stokes flow and compressible linear elasticity are presented. The second class of methods is applied to the Poisson, Timoshenko beam and incompressible elasticity problems. Numerical results demonstrate the good stability and accuracy of the methods, and confirm the error estimates

An Automated Processing Method for Agglomeration Areas

Directory of Open Access Journals (Sweden)

Chengming Li

2018-05-01

Full Text Available Agglomeration operations are a core component of the automated generalization of aggregated area groups. However, because geographical elements that possess agglomeration features are relatively scarce, the current literature has not given sufficient attention to agglomeration operations. Furthermore, most reports on the subject are limited to the general conceptual level. Consequently, current agglomeration methods are highly reliant on subjective determinations and cannot support intelligent computer processing. This paper proposes an automated processing method for agglomeration areas. Firstly, the proposed method automatically identifies agglomeration areas based on the width of the striped bridging area, distribution pattern index (DPI, shape similarity index (SSI, and overlap index (OI. Next, the progressive agglomeration operation is carried out, including the computation of the external boundary outlines and the extraction of agglomeration lines. The effectiveness and rationality of the proposed method has been validated by using actual census data of Chinese geographical conditions in the Jiangsu Province.

Design and Optimization of Capacitated Supply Chain Networks Including Quality Measures

Directory of Open Access Journals (Sweden)

Krystel K. Castillo-Villar

2014-01-01

Full Text Available This paper presents (1 a novel capacitated model for supply chain network design which considers manufacturing, distribution, and quality costs (named SCND-COQ model and (2 five combinatorial optimization methods, based on nonlinear optimization, heuristic, and metaheuristic approaches, which are used to solve realistic instances of practical size. The SCND-COQ model is a mixed-integer nonlinear problem which can be used at a strategic planning level to design a supply chain network that maximizes the total profit subject to meeting an overall quality level of the final product at minimum costs. The SCND-COQ model computes the quality-related costs for the whole supply chain network considering the interdependencies among business entities. The effectiveness of the proposed solution approaches is shown using numerical experiments. These methods allow solving more realistic (capacitated supply chain network design problems including quality-related costs (inspections, rework, opportunity costs, and others within a reasonable computational time.

Tax Policy Trends: Republicans Reveal Proposed Tax Overhaul

Directory of Open Access Journals (Sweden)

Philip Bazel

2017-10-01

Full Text Available REPUBLICANS REVEAL PROPOSED TAX OVERHAUL The White House and Congressional Republicans have revealed their much-anticipated proposal for reform of the U.S. personal and corporate tax systems. The proposal titled, “UNIFIED FRAMEWORK FOR FIXING OUR BROKEN TAX CODE” outlines a number of central policy changes, which will significantly alter the U.S. corporate tax system. The proposal includes a top federal marginal rate reduction for the sole proprietorships, partnerships and S corporation—small business equivalents— from 39.6% to 25% (state income tax rates would no longer be deductible. Large corporations would also see a meaningful federal rate reduction given the proposed drop in the federal corporate income tax rate from 35% to 20%. Additionally, the proposal includes a generous temporary measure intended to stimulate investment, full capital expensing for machinery with a partial limitation of interest deductions.

A proposal for a determination method of element division on an analytical model for finite element elastic waves propagation analysis

International Nuclear Information System (INIS)

Ishida, Hitoshi; Meshii, Toshiyuki

2010-01-01

This study proposes an element size selection method named the 'Impact-Meshing (IM) method' for a finite element waves propagation analysis model, which is characterized by (1) determination of element division of the model with strain energy in the whole model, (2) static analysis (dynamic analysis in a single time step) with boundary conditions which gives a maximum change of displacement in the time increment and inertial (impact) force caused by the displacement change. In this paper, an example of application of the IM method to 3D ultrasonic wave propagation problem in an elastic solid is described. These examples showed an analysis result with a model determined by the IM method was convergence and calculation time for determination of element subdivision was reduced to about 1/6 by the IM Method which did not need determination of element subdivision by a dynamic transient analysis with 100 time steps. (author)

R3GMRES: including prior information in GMRES-type methods for discrete inverse problems

DEFF Research Database (Denmark)

Dong, Yiqiu; Garde, Henrik; Hansen, Per Christian

2014-01-01

Lothar Reichel and his collaborators proposed several iterative algorithms that augment the underlying Krylov subspace with an additional low-dimensional subspace in order to produce improved regularized solutions. We take a closer look at this approach and investigate a particular Regularized Ra...

A proposed descriptive methodology for environmental geologic (envirogeologic) site characterization

International Nuclear Information System (INIS)

Schwarz, D.L.; Snyder, W.S.

1994-01-01

We propose a descriptive methodology for use in environmental geologic (envirogeologic) site characterization. The method uses traditional sedimentologic descriptions augmented by environmental data needs, and facies analysis. Most other environmental methodologies for soil and sediment characterization use soil engineering and engineering geology techniques that classify by texture and engineering properties. This technique is inadequate for envirogeologic characterization of sediments. In part, this inadequacy is due to differences in the grain-size between the Unified soil Classification and the Udden-Wentworth scales. Use of the soil grain-size classification could easily cause confusion when attempting to relate descriptions based on this classification to our basic understanding of sedimentary depositional systems. The proposed envirogeologic method uses descriptive parameters to characterize a sediment sample, suggests specific tests on samples for adequate characterization, and provides a guidelines for subsurface facies analysis, based on data retrieved from shallow boreholes, that will allow better predictive models to be developed. This methodology should allow for both a more complete site assessment, and provide sufficient data for selection of the appropriate remediation technology, including bioremediation. 50 refs

Thermal enhanced vapor extraction systems: Design, application and performance prediction including contaminant behavior

International Nuclear Information System (INIS)

Phelan, J.M.; Webb, S.W.

1994-01-01

Soil heating technologies have been proposed as a method to accelerate contaminant removal from subsurface soils. These methods include the use of hot air, steam, conductive heaters, in-situ resistive heating and in-situ radiofrequency heating (Buettner et.al., EPA, Dev et.al., Heath et.al.). Criteria for selection of a particular soil heating technology is a complex function of contaminant and soil properties, and efficiency in energy delivery and contaminant removal technologies. The work presented here seeks to expand the understanding of the interactions of subsurface water, contaminant, heat and vacuum extraction through model predictions and field data collection. Field demonstration will involve the combination of two soil heating technologies (resistive and dielectric) with a vacuum vapor extraction system and will occur during the summer of 1994

A quantitative method for assessing resilience of interdependent infrastructures

International Nuclear Information System (INIS)

Nan, Cen; Sansavini, Giovanni

2017-01-01

The importance of understanding system resilience and identifying ways to enhance it, especially for interdependent infrastructures our daily life depends on, has been recognized not only by academics, but also by the corporate and public sectors. During recent years, several methods and frameworks have been proposed and developed to explore applicable techniques to assess and analyze system resilience in a comprehensive way. However, they are often tailored to specific disruptive hazards/events, or fail to properly include all the phases such as absorption, adaptation, and recovery. In this paper, a quantitative method for the assessment of the system resilience is proposed. The method consists of two components: an integrated metric for system resilience quantification and a hybrid modeling approach for representing the failure behavior of infrastructure systems. The feasibility and applicability of the proposed method are tested using an electric power supply system as the exemplary infrastructure. Simulation results highlight that the method proves effective in designing, engineering and improving the resilience of infrastructures. Finally, system resilience is proposed as a proxy to quantify the coupling strength between interdependent infrastructures. - Highlights: • A method for quantifying resilience of interdependent infrastructures is proposed. • It combines multi-layer hybrid modeling and a time-dependent resilience metric. • The feasibility of the proposed method is tested on the electric power supply system. • The method provides insights to decision-makers for strengthening system resilience. • Resilience capabilities can be used to engineer interdependencies between subsystems.

Proposed first-generation WSQ bit allocation procedure

Energy Technology Data Exchange (ETDEWEB)

Bradley, J.N.; Brislawn, C.M.

1993-09-08

The Wavelet/Scalar Quantization (WSQ) gray-scale fingerprint image compression algorithm involves a symmetric wavelet transform (SWT) image decomposition followed by uniform scalar quantization of each subband. The algorithm is adaptive insofar as the bin widths for the scalar quantizers are image-specific and are included in the compressed image format. Since the decoder requires only the actual bin width values -- but not the method by which they were computed -- the standard allows for future refinements of the WSQ algorithm by improving the method used to select the scalar quantizer bin widths. This report proposes a bit allocation procedure for use with the first-generation WSQ encoder. In previous work a specific formula is provided for the relative sizes of the scalar quantizer bin widths in terms of the variances of the SWT subbands. An explicit specification for the constant of proportionality, q, that determines the absolute bin widths was not given. The actual compression ratio produced by the WSQ algorithm will generally vary from image to image depending on the amount of coding gain obtained by the run-length and Huffman coding, stages of the algorithm, but testing performed by the FBI established that WSQ compression produces archival quality images at compression ratios of around 20 to 1. The bit allocation procedure described in this report possesses a control parameter, r, that can be set by the user to achieve a predetermined amount of lossy compression, effectively giving the user control over the amount of distortion introduced by quantization noise. The variability observed in final compression ratios is thus due only to differences in lossless coding gain from image to image, chiefly a result of the varying amounts of blank background surrounding the print area in the images. Experimental results are presented that demonstrate the proposed method`s effectiveness.

Proposal for automated transformations on single-photon multipath qudits

Science.gov (United States)

Baldijão, R. D.; Borges, G. F.; Marques, B.; Solís-Prosser, M. A.; Neves, L.; Pádua, S.

2017-09-01

We propose a method for implementing automated state transformations on single-photon multipath qudits encoded in a one-dimensional transverse spatial domain. It relies on transferring the encoding from this domain to the orthogonal one by applying a spatial phase modulation with diffraction gratings, merging all the initial propagation paths by using a stable interferometric network, and filtering out the unwanted diffraction orders. The automation feature is attained by utilizing a programmable phase-only spatial light modulator (SLM) where properly designed diffraction gratings displayed on its screen will implement the desired transformations, including, among others, projections, permutations, and random operations. We discuss the losses in the process which is, in general, inherently nonunitary. Some examples of transformations are presented and, considering a realistic scenario, we analyze how they will be affected by the pixelated structure of the SLM screen. The method proposed here enables one to implement much more general transformations on multipath qudits than is possible with a SLM alone operating in the diagonal basis of which-path states. Therefore, it will extend the range of applicability for this encoding in high-dimensional quantum information and computing protocols as well as fundamental studies in quantum theory.

New adaptive sampling method in particle image velocimetry

International Nuclear Information System (INIS)

Yu, Kaikai; Xu, Jinglei; Tang, Lan; Mo, Jianwei

2015-01-01

This study proposes a new adaptive method to enable the number of interrogation windows and their positions in a particle image velocimetry (PIV) image interrogation algorithm to become self-adapted according to the seeding density. The proposed method can relax the constraint of uniform sampling rate and uniform window size commonly adopted in the traditional PIV algorithm. In addition, the positions of the sampling points are redistributed on the basis of the spring force generated by the sampling points. The advantages include control of the number of interrogation windows according to the local seeding density and smoother distribution of sampling points. The reliability of the adaptive sampling method is illustrated by processing synthetic and experimental images. The synthetic example attests to the advantages of the sampling method. Compared with that of the uniform interrogation technique in the experimental application, the spatial resolution is locally enhanced when using the proposed sampling method. (technical design note)

A sensitive multi-residue method for the determination of 35 micropollutants including pharmaceuticals, iodinated contrast media and pesticides in water.

Science.gov (United States)

Valls-Cantenys, Carme; Scheurer, Marco; Iglesias, Mònica; Sacher, Frank; Brauch, Heinz-Jürgen; Salvadó, Victoria

2016-09-01

A sensitive, multi-residue method using solid-phase extraction followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed to determine a representative group of 35 analytes, including corrosion inhibitors, pesticides and pharmaceuticals such as analgesic and anti-inflammatory drugs, five iodinated contrast media, β-blockers and some of their metabolites and transformation products in water samples. Few other methods are capable of determining such a broad range of contrast media together with other analytes. We studied the parameters affecting the extraction of the target analytes, including sorbent selection and extraction conditions, their chromatographic separation (mobile phase composition and column) and detection conditions using two ionisation sources: electrospray ionisation (ESI) and atmospheric pressure chemical ionisation (APCI). In order to correct matrix effects, a total of 20 surrogate/internal standards were used. ESI was found to have better sensitivity than APCI. Recoveries ranging from 79 to 134 % for tap water and 66 to 144 % for surface water were obtained. Intra-day precision, calculated as relative standard deviation, was below 34 % for tap water and below 21 % for surface water, groundwater and effluent wastewater. Method quantification limits (MQL) were in the low ng L(-1) range, except for the contrast agents iomeprol, amidotrizoic acid and iohexol (22, 25.5 and 17.9 ng L(-1), respectively). Finally, the method was applied to the analysis of 56 real water samples as part of the validation procedure. All of the compounds were detected in at least some of the water samples analysed. Graphical Abstract Multi-residue method for the determination of micropollutants including pharmaceuticals, iodinated contrast media and pesticides in waters by LC-MS/MS.

The Frontlines of Medicine Project: a proposal for the standardized communication of emergency department data for public health uses including syndromic surveillance for biological and chemical terrorism.

Science.gov (United States)

Barthell, Edward N; Cordell, William H; Moorhead, John C; Handler, Jonathan; Feied, Craig; Smith, Mark S; Cochrane, Dennis G; Felton, Christopher W; Collins, Michael A

2002-04-01

The Frontlines of Medicine Project is a collaborative effort of emergency medicine (including emergency medical services and clinical toxicology), public health, emergency government, law enforcement, and informatics. This collaboration proposes to develop a nonproprietary, "open systems" approach for reporting emergency department patient data. The common element is a standard approach to sending messages from individual EDs to regional oversight entities that could then analyze the data received. ED encounter data could be used for various public health initiatives, including syndromic surveillance for chemical and biological terrorism. The interlinking of these regional systems could also permit public health surveillance at a national level based on ED patient encounter data. Advancements in the Internet and Web-based technologies could allow the deployment of these standardized tools in a rapid time frame.

Proposing and testing SOA governance process: A case study approach

DEFF Research Database (Denmark)

Koumaditis, Konstantinos; Themistocleous, Marinos

2015-01-01

Longstanding Healthcare Information Systems (HIS) integration challenges drove healthcare organisations to invest in new paradigms like Service Oriented Architecture (SOA). Yet, SOA holds challenges of its own, with SOA Governance surfacing on the top. This research depicts the development......, grounded in the normative literature and further developed to include healthcare aspects. The proposition is tested in a large Greek hospital utilising qualitative methods and the findings presented herein. This proposal aims to pinpoint attributes and guidelines for SOA Governance Process, required...

A FILTRATION METHOD AND APPARATUS INCLUDING A ROLLER WITH PORES

DEFF Research Database (Denmark)

2008-01-01

The present invention offers a method for separating dry matter from a medium. A separation chamber is at least partly defined by a plurality of rollers (2,7) and is capable of being pressure regulated. At least one of the rollers is a pore roller (7) having a surface with pores allowing permeabi...

Proposal of adaptive human interface and study of interface evaluation method for plant operators

International Nuclear Information System (INIS)

Ujita, Hiroshi; Kubota, Ryuji.

1994-01-01

In this report, a new concept of human interface adaptive to plant operators' mental model, cognitive process and psychological state which change with time is proposed. It is composed of a function to determine information which should be indicated to operators based on the plant situation, a function to estimate operators' internal conditions, and a function to arrange the information amount, position, timing, form etc. based on their conditions. The method to evaluate the fitness of the interface by using the analysis results based on cognitive science, ergonomics, psychology and physiology is developed to achieve such an interface. Fundamental physiological experiments have been performed. Stress and workload can be identified by the ratio of the power average of the α wave fraction of a brain wave and be distinguished by the ratio of the standard deviation of the R-R interval in test and at rest, in the case of low stress such as mouse operation, calculation and walking. (author)

Proposal of adaptive human interface and study of interface evaluation method for plant operators

Energy Technology Data Exchange (ETDEWEB)

Ujita, Hiroshi [Hitachi Ltd., Ibaraki (Japan). Energy Research Lab.; Kubota, Ryuji

1994-07-01

In this report, a new concept of human interface adaptive to plant operators' mental model, cognitive process and psychological state which change with time is proposed. It is composed of a function to determine information which should be indicated to operators based on the plant situation, a function to estimate operators' internal conditions, and a function to arrange the information amount, position, timing, form etc. based on their conditions. The method to evaluate the fitness of the interface by using the analysis results based on cognitive science, ergonomics, psychology and physiology is developed to achieve such an interface. Fundamental physiological experiments have been performed. Stress and workload can be identified by the ratio of the power average of the [alpha] wave fraction of a brain wave and be distinguished by the ratio of the standard deviation of the R-R interval in test and at rest, in the case of low stress such as mouse operation, calculation and walking. (author).

A Network Reconfiguration Method Considering Data Uncertainties in Smart Distribution Networks

Directory of Open Access Journals (Sweden)

Ke-yan Liu

2017-05-01

Full Text Available This work presents a method for distribution network reconfiguration with the simultaneous consideration of distributed generation (DG allocation. The uncertainties of load fluctuation before the network reconfiguration are also considered. Three optimal objectives, including minimal line loss cost, minimum Expected Energy Not Supplied, and minimum switch operation cost, are investigated. The multi-objective optimization problem is further transformed into a single-objective optimization problem by utilizing weighting factors. The proposed network reconfiguration method includes two periods. The first period is to create a feasible topology network by using binary particle swarm optimization (BPSO. Then the DG allocation problem is solved by utilizing sensitivity analysis and a Harmony Search algorithm (HSA. In the meanwhile, interval analysis is applied to deal with the uncertainties of load and devices parameters. Test cases are studied using the standard IEEE 33-bus and PG&E 69-bus systems. Different scenarios and comparisons are analyzed in the experiments. The results show the applicability of the proposed method. The performance analysis of the proposed method is also investigated. The computational results indicate that the proposed network reconfiguration algorithm is feasible.

A proposed method to detect kinematic differences between and within individuals.

Science.gov (United States)

Frost, David M; Beach, Tyson A C; McGill, Stuart M; Callaghan, Jack P

2015-06-01

The primary objective was to examine the utility of a novel method of detecting "actual" kinematic changes using the within-subject variation. Twenty firefighters were assigned to one of two groups (lifting or firefighting). Participants performed 25 repetitions of two lifting or firefighting tasks, in three sessions. The magnitude and within-subject variation of several discrete kinematic measures were computed. Sequential averages of each variable were used to derive a cubic, quadratic and linear regression equation. The efficacy of each equation was examined by contrasting participants' sequential means to their 25-trial mean±1SD and 2SD. The magnitude and within-subject variation of each dependent measure was repeatable for all tasks; however, each participant did not exhibit the same movement patterns as the group. The number of instances across all variables, tasks and testing sessions whereby the 25-trial mean±1SD was contained within the boundaries established by the regression equations increased as the aggregate scores included more trials. Each equation achieved success in at least 88% of all instances when three trials were included in the sequential mean (95% with five trials). The within-subject variation may offer a means to examine participant-specific changes without having to collect a large number of trials. Copyright © 2015 Elsevier Ltd. All rights reserved.

Robust keyword retrieval method for OCRed text

Science.gov (United States)

Fujii, Yusaku; Takebe, Hiroaki; Tanaka, Hiroshi; Hotta, Yoshinobu

2011-01-01

Document management systems have become important because of the growing popularity of electronic filing of documents and scanning of books, magazines, manuals, etc., through a scanner or a digital camera, for storage or reading on a PC or an electronic book. Text information acquired by optical character recognition (OCR) is usually added to the electronic documents for document retrieval. Since texts generated by OCR generally include character recognition errors, robust retrieval methods have been introduced to overcome this problem. In this paper, we propose a retrieval method that is robust against both character segmentation and recognition errors. In the proposed method, the insertion of noise characters and dropping of characters in the keyword retrieval enables robustness against character segmentation errors, and character substitution in the keyword of the recognition candidate for each character in OCR or any other character enables robustness against character recognition errors. The recall rate of the proposed method was 15% higher than that of the conventional method. However, the precision rate was 64% lower.

The challenges facing ethnographic design research: A proposed methodological solution

DEFF Research Database (Denmark)

Cash, Philip; Hicks, Ben; Culley, Steve

2009-01-01

Central to improving and maintaining high levels of performance in emerging ethnographic design research is a fundamental requirement to address some of the problems associated with the subject. In particular seven core issues are identified and include the complexity of test development......, variability of methods, resource intensiveness, subjectivity, comparability, common metrics and industrial acceptance. To address these problems this paper describes a structured methodological approach in which three main areas are proposed, the modularisation of the research process, the standardisation...... of the dataset and the stratification of the research context. The paper then examines the fundamental requirements of this scheme and how these relate to a Design Observatory approach. Following this, the proposed solution is related back to the initial problem set and potential issues are discussed. Finally...

Clinton administration budget includes mixed bag for science

Science.gov (United States)

Showstack, Randy

The $1,766 trillion federal budget proposal that the Clinton Administration rolled out on February 1—which promises to protect Social Security and Medicare and work within mandated budget caps—generally provides favorable news for federally funded science research and development.Within the 17% ($592 billion) of the federal budget earmarked for discretionary spending, the Administration's budget proposal increases funding for nondefense research and development for the seventh year in a row. This includes increased funding for a number of science accounts and money for a series of new science initiatives.

7 CFR 984.437 - Methods for proposing names of additional candidates to be included on walnut growers' nomination...

Science.gov (United States)

2010-01-01

....35(a)(5) and (b)(6), any ten or more such growers who marketed an aggregate of 500 or more tons of... specified in § 984.35(a)(3) and (4) or § 984.35(b)(4) and (5) and who marketed an aggregate of 500 or more... section shall be on forms supplied by the Board and filed no later than April 1 of the nomination year...

Standardized patients in audiology: a proposal for a new method of evaluating clinical competence.

Science.gov (United States)

Dinsmore, Brooke Freeman; Bohnert, Carrie; Preminger, Jill E

2013-05-01

While accrediting organizations require AuD programs to provide evidence that their students are able to demonstrate knowledge and competencies in specific content areas, there are no generally accepted mechanisms for the assessment and the measurement of these proficiencies. We propose that AuD programs consider developing standardized patient (SP) cases in order to develop consistent summative assessment programs within and across universities. The purpose of this article is to provide a framework for establishing SP programs to evaluate competencies in AuD students by detailing the history of SP cases and their use, developing a rationale for this method of assessment, and outlining the steps for writing and implementing SP cases. Literature review. SPs have been used to assess clinical competence in medical students for over 50 yr. The prevalence of SP assessment in allied health professions (e.g., dentistry, psychology, pharmacy) has increased over the last two decades but has only gained a limited following in audiology. SP assessment has been implemented in medical education using the Objective Structured Clinical Examination, a multistation, timed exam that uses fictional cases to assess students' clinical abilities. To date, only one published report has been completed that evaluates the use of SPs to assess clinical abilities in audiology students. This article expands upon the work of English et al (2007) and their efforts to use SPs to evaluate counseling abilities. To this end, we describe the steps necessary to write a case, procedures to determine performance requirements, and the need to develop remediation plans. As an example, we include a case that we have developed in order to evaluate vestibular assessment and patient communication skills. Utilizing SP assessment in audiology education would provide useful means to evaluate competence in a uniform way. Future research is necessary to develop reliable and valid cases that may be implemented

Mixed Methods in Intervention Research: Theory to Adaptation

Science.gov (United States)

Nastasi, Bonnie K.; Hitchcock, John; Sarkar, Sreeroopa; Burkholder, Gary; Varjas, Kristen; Jayasena, Asoka

2007-01-01

The purpose of this article is to demonstrate the application of mixed methods research designs to multiyear programmatic research and development projects whose goals include integration of cultural specificity when generating or translating evidence-based practices. The authors propose a set of five mixed methods designs related to different…

Method for including detailed evaluation of daylight levels in Be06

DEFF Research Database (Denmark)

Petersen, Steffen

2008-01-01

Good daylight conditions in office buildings have become an important issue due to new European regulatory demands which include energy consumption for electrical lighting in the building energy frame. Good daylight conditions in offices are thus in increased focus as an energy conserving measure....... In order to evaluate whether a certain design is good daylight design or not building designers must perform detailed evaluation of daylight levels, including the daylight performance of dynamic solar shadings, and include these in the energy performance evaluation. However, the mandatory national...... calculation tool in Denmark (Be06) for evaluating the energy performance of buildings is currently using a simple representation of available daylight in a room and simple assumptions regarding the control of shading devices. In a case example, this is leading to an overestimation of the energy consumption...

Calculation method of the desiccant amount for the protection of packed electronic equipments and its comparison with other methods currently used

International Nuclear Information System (INIS)

Del Valle, J.C.; Guido, O.O.

1982-01-01

The silica gel characteristics and properties are reviewed from the viewpoint of its use as a desiccant under static conditions. There were developed two calculation methods of the desiccant amount required for the protection from moisture of electronic equipments packed into rigid synthetic foam containers, for a given period and with an adequate safety margin. Besides, MIL specifications methods applicable to this type of packages have been also included. The proposed method considers the depression due to the contraction of the inside air volume during the temperature decrease periods as the only cause of the water vapor ingress into the container, the moisture permeation by diffusion through the closed cell synthetic foams being negligible. Owing to the marked thermal inertia of the package material, the thermal amplitude inside the container is lower than the outside thermal amplitude; therefore the method includes the calculation of the former. The other method is based on a procedure applicable to large storage rooms, briefly described in the literature, and where the moisture entrance is due to the above mentioned cause. A test to verify the reliability of the estimation is proposed. Finally, the amount of silica gel required for the protection of an electronic equipment packed in a given container has been calculated by the aforementioned methods, and the results compared. The value found by the proposed method was over 30% lower than that obtained by the most adequate procedure described in the MIL specification. (author) [es

The review and results of different methods for facial recognition

Science.gov (United States)

Le, Yifan

2017-09-01

In recent years, facial recognition draws much attention due to its wide potential applications. As a unique technology in Biometric Identification, facial recognition represents a significant improvement since it could be operated without cooperation of people under detection. Hence, facial recognition will be taken into defense system, medical detection, human behavior understanding, etc. Several theories and methods have been established to make progress in facial recognition: (1) A novel two-stage facial landmark localization method is proposed which has more accurate facial localization effect under specific database; (2) A statistical face frontalization method is proposed which outperforms state-of-the-art methods for face landmark localization; (3) It proposes a general facial landmark detection algorithm to handle images with severe occlusion and images with large head poses; (4) There are three methods proposed on Face Alignment including shape augmented regression method, pose-indexed based multi-view method and a learning based method via regressing local binary features. The aim of this paper is to analyze previous work of different aspects in facial recognition, focusing on concrete method and performance under various databases. In addition, some improvement measures and suggestions in potential applications will be put forward.

Proposed algorithm to improve job shop production scheduling using ant colony optimization method

Science.gov (United States)

Pakpahan, Eka KA; Kristina, Sonna; Setiawan, Ari

2017-12-01

This paper deals with the determination of job shop production schedule on an automatic environment. On this particular environment, machines and material handling system are integrated and controlled by a computer center where schedule were created and then used to dictate the movement of parts and the operations at each machine. This setting is usually designed to have an unmanned production process for a specified interval time. We consider here parts with various operations requirement. Each operation requires specific cutting tools. These parts are to be scheduled on machines each having identical capability, meaning that each machine is equipped with a similar set of cutting tools therefore is capable of processing any operation. The availability of a particular machine to process a particular operation is determined by the remaining life time of its cutting tools. We proposed an algorithm based on the ant colony optimization method and embedded them on matlab software to generate production schedule which minimize the total processing time of the parts (makespan). We test the algorithm on data provided by real industry and the process shows a very short computation time. This contributes a lot to the flexibility and timelines targeted on an automatic environment.

Proposals for regional cooperation in Africa

International Nuclear Information System (INIS)

Diaco, T.

1999-01-01

This presentation includes proposals for regional cooperation in Africa in the field of seismic monitoring and proposes future actions for establishing this cooperation. It emphasises the benefits of regional cooperation meaning scientific benefit from an established data base, as well as benefit in the field of geology, meteorology, geophysics and in unified budgets and logistics

A text zero-watermarking method based on keyword dense interval

Science.gov (United States)

Yang, Fan; Zhu, Yuesheng; Jiang, Yifeng; Qing, Yin

2017-07-01

Digital watermarking has been recognized as a useful technology for the copyright protection and authentication of digital information. However, rarely did the former methods focus on the key content of digital carrier. The idea based on the protection of key content is more targeted and can be considered in different digital information, including text, image and video. In this paper, we use text as research object and a text zero-watermarking method which uses keyword dense interval (KDI) as the key content is proposed. First, we construct zero-watermarking model by introducing the concept of KDI and giving the method of KDI extraction. Second, we design detection model which includes secondary generation of zero-watermark and the similarity computing method of keyword distribution. Besides, experiments are carried out, and the results show that the proposed method gives better performance than other available methods especially in the attacks of sentence transformation and synonyms substitution.

Mining method selection by integrated AHP and PROMETHEE method.

Science.gov (United States)

Bogdanovic, Dejan; Nikolic, Djordje; Ilic, Ivana

2012-03-01

Selecting the best mining method among many alternatives is a multicriteria decision making problem. The aim of this paper is to demonstrate the implementation of an integrated approach that employs AHP and PROMETHEE together for selecting the most suitable mining method for the "Coka Marin" underground mine in Serbia. The related problem includes five possible mining methods and eleven criteria to evaluate them. Criteria are accurately chosen in order to cover the most important parameters that impact on the mining method selection, such as geological and geotechnical properties, economic parameters and geographical factors. The AHP is used to analyze the structure of the mining method selection problem and to determine weights of the criteria, and PROMETHEE method is used to obtain the final ranking and to make a sensitivity analysis by changing the weights. The results have shown that the proposed integrated method can be successfully used in solving mining engineering problems.

Proposed torque optimized behavior for digital speed control of induction motors

Energy Technology Data Exchange (ETDEWEB)

Metwally, H.M.B.; El-Shewy, H.M.; El-Kholy, M.M. [Zagazig Univ., Dept. of Electrical Engineering, Zagazig (Egypt); Abdel-Kader, F.E. [Menoufyia Univ., Dept. of Electrical Engineering, Menoufyia (Egypt)

2002-09-01

In this paper, a control strategy for speed control of induction motors with field orientation is proposed. The proposed method adjusts the output voltage and frequency of the converter to operate the motor at the desired speed with maximum torque per ampere at all load torques keeping the torque angle equal to 90 deg. A comparison between the performance characteristics of a 2 hp induction motor using three methods of speed control is presented. These methods are the proposed method, the direct torque control method and the constant V/f method. The comparison showed that better performance characteristics are obtained using the proposed speed control strategy. A computer program, based on this method, is developed. Starting from the motor parameters, the program calculates a data set for the stator voltage and frequency required to obtain maximum torque per ampere at any motor speed and load torque. This data set can be used by the digital speed control system of induction motors. (Author)

EMergy analysis perspectives of Thailand and Mekong River dam proposals

International Nuclear Information System (INIS)

Brown, M.T.; McClanahan, T.R.

1996-01-01

Methods of EMergy analysis (a scientifically based measure of wealth with units of solar emjoules (sej)) are explained and illustrated, using the economy of Thailand and two proposed dams on the Mekong River. Thailand's EMergy/$ ratio is near the world average (3.46 ·10 12 sej/$), its EMergy per capita ratio (2.98·10 15 sej/capita) is low compared to developed economies (that of the United States is 29.3·10 15 sej/capita), and its EMergy balance of payments is negative (the EMergy in exports is almost twice the EMergy in imports). The calculated net yield ratios of the proposed dams were sensitive to the treatment of sediments. The analysis yielded high net yield ratios (12.3/1 and 20.3/1) if sediments were not included, but yielded ratios of only 1.4/1 and 1.3/1 if sediments were included. If the two dams were constructed as a cascade, the combined net yield ratio was 2.5/1 (sediments included). If compared to conventional fossil fuels as a primary source of energy to the economy, the net yield ratio of the electricity generated from the two-dam cascade expressed as fossil fuels was 7.4/1

An Efficient Approach for Identifying Stable Lobes with Discretization Method

Directory of Open Access Journals (Sweden)

Baohai Wu

2013-01-01

Full Text Available This paper presents a new approach for quick identification of chatter stability lobes with discretization method. Firstly, three different kinds of stability regions are defined: absolute stable region, valid region, and invalid region. Secondly, while identifying the chatter stability lobes, three different regions within the chatter stability lobes are identified with relatively large time intervals. Thirdly, stability boundary within the valid regions is finely calculated to get exact chatter stability lobes. The proposed method only needs to test a small portion of spindle speed and cutting depth set; about 89% computation time is savedcompared with full discretization method. It spends only about10 minutes to get exact chatter stability lobes. Since, based on discretization method, the proposed method can be used for different immersion cutting including low immersion cutting process, the proposed method can be directly implemented in the workshop to promote machining parameters selection efficiency.

Stochastic modelling of two-phase flows including phase change

International Nuclear Information System (INIS)

Hurisse, O.; Minier, J.P.

2011-01-01

Stochastic modelling has already been developed and applied for single-phase flows and incompressible two-phase flows. In this article, we propose an extension of this modelling approach to two-phase flows including phase change (e.g. for steam-water flows). Two aspects are emphasised: a stochastic model accounting for phase transition and a modelling constraint which arises from volume conservation. To illustrate the whole approach, some remarks are eventually proposed for two-fluid models. (authors)

A Review of Design Optimization Methods for Electrical Machines

Directory of Open Access Journals (Sweden)

Gang Lei

2017-11-01

Full Text Available Electrical machines are the hearts of many appliances, industrial equipment and systems. In the context of global sustainability, they must fulfill various requirements, not only physically and technologically but also environmentally. Therefore, their design optimization process becomes more and more complex as more engineering disciplines/domains and constraints are involved, such as electromagnetics, structural mechanics and heat transfer. This paper aims to present a review of the design optimization methods for electrical machines, including design analysis methods and models, optimization models, algorithms and methods/strategies. Several efficient optimization methods/strategies are highlighted with comments, including surrogate-model based and multi-level optimization methods. In addition, two promising and challenging topics in both academic and industrial communities are discussed, and two novel optimization methods are introduced for advanced design optimization of electrical machines. First, a system-level design optimization method is introduced for the development of advanced electric drive systems. Second, a robust design optimization method based on the design for six-sigma technique is introduced for high-quality manufacturing of electrical machines in production. Meanwhile, a proposal is presented for the development of a robust design optimization service based on industrial big data and cloud computing services. Finally, five future directions are proposed, including smart design optimization method for future intelligent design and production of electrical machines.

Implementation aspects of the Boundary Element Method including viscous and thermal losses

DEFF Research Database (Denmark)

Cutanda Henriquez, Vicente; Juhl, Peter Møller

2014-01-01

The implementation of viscous and thermal losses using the Boundary Element Method (BEM) is based on the Kirchhoff’s dispersion relation and has been tested in previous work using analytical test cases and comparison with measurements. Numerical methods that can simulate sound fields in fluids...

A Novel Protection Method for Single Line-to-Ground Faults in Ungrounded Low-Inertia Microgrids

Directory of Open Access Journals (Sweden)

Liuming Jing

2016-06-01

Full Text Available This paper proposes a novel protection method for single line-to-ground (SLG faults in ungrounded low-inertia microgrids. The proposed method includes microgrid interface protection and unit protection. The microgrid interface protection is based on the difference between the zero-sequence voltage angle and the zero-sequence current angle at the microgrid interconnection transformer for fast selection of the faulty feeder. The microgrid unit protection is based on a comparison of the three zero-sequence current phase directions at each junction point of load or distributed energy resources. Methods are also included to locate the minimum fault section. The fault section location technology operates according to the coordination of microgrid unit protection. The proposed method responds to SLG faults that may occur in both the grid and the microgrid. Simulations of an ungrounded low-inertia microgrid with a relay model were carried out using Power System Computer Aided Design (PSCAD/Electromagnetic Transients including DC (EMTDC.

Proposal of a segmentation procedure for skid resistance data

International Nuclear Information System (INIS)

Tejeda, S. V.; Tampier, Hernan de Solominihac; Navarro, T.E.

2008-01-01

Skin resistance of pavements presents a high spatial variability along a road. This pavement characteristic is directly related to wet weather accidents; therefore, it is important to identify and characterize the skid resistance of homogeneous segments along a road in order to implement proper road safety management. Several data segmentation methods have been applied to other pavement characteristics (e.g. roughness). However, no application to skin resistance data was found during the literature review for this study. Typical segmentation methods are rather too general or too specific to ensure a detailed segmentation of skid resistance data, which can be used for managing pavement performance. The main objective of this paper is to propose a procedure for segmenting skid resistance data, based on existing data segmentation methods. The procedure needs to be efficient and to fulfill road management requirements. The proposed procedure considers the Leverage method to identify outlier data, the CUSUM method to accomplish initial data segmentation and a statistical method to group consecutive segments that are statistically similar. The statistical method applies the Student's t-test of mean equities, along with analysis of variance and the Tuckey test for the multiple comparison of means. The proposed procedure was applied to a sample of skid resistance data measured with SCRIM (Side Force Coefficient Routine Investigatory Machine) on a 4.2 km section of Chilean road and was compared to conventional segmentation methods. Results showed that the proposed procedure is more efficient than the conventional segmentation procedures, achieving the minimum weighted sum of square errors (SSEp) with all the identified segments statistically different. Due to its mathematical basis, proposed procedure can be easily adapted and programmed for use in road safety management. (author)

Charge separation at nanoscale interfaces: energy-level alignment including two-quasiparticle interactions.

Science.gov (United States)

Li, Huashan; Lin, Zhibin; Lusk, Mark T; Wu, Zhigang

2014-10-21

The universal and fundamental criteria for charge separation at interfaces involving nanoscale materials are investigated. In addition to the single-quasiparticle excitation, all the two-quasiparticle effects including exciton binding, Coulomb stabilization, and exciton transfer are considered, which play critical roles on nanoscale interfaces for optoelectronic applications. We propose a scheme allowing adding these two-quasiparticle interactions on top of the single-quasiparticle energy level alignment for determining and illuminating charge separation at nanoscale interfaces. Employing the many-body perturbation theory based on Green's functions, we quantitatively demonstrate that neglecting or simplifying these crucial two-quasiparticle interactions using less accurate methods is likely to predict qualitatively incorrect charge separation behaviors at nanoscale interfaces where quantum confinement dominates.

A Proposal to Build an Education Research and Development Program: The Kamehameha Early Education Project Proposal. Technical Report #3.

Science.gov (United States)

Gallimore, Ronald; And Others

This report summarizes the programmatic features of a proposal for the Kamehameha Early Education Project (KEEP), a program aimed at the development, demonstration, and dissemination of methods for improving the education of Hawaiian and part-Hawaiian children. A brief description of the proposed project goals, structure, organization, and…

Study on A Control Method of PAPF for Resonance Damping and Harmonics Compensation in Power System

DEFF Research Database (Denmark)

Zhou, Fang; Wu, Longhui; Chen, Zhe

2009-01-01

In power system, capacitors are widely used to compensate reactive power, which generally cause resonance problems in harmonic distorted network. In this paper, A method of using a parallel active power filter (PAPF) to damp the resonances is proposed. The proposed method is compound with traditi......In power system, capacitors are widely used to compensate reactive power, which generally cause resonance problems in harmonic distorted network. In this paper, A method of using a parallel active power filter (PAPF) to damp the resonances is proposed. The proposed method is compound...... with traditional method, it shows that whether the capacitor current is included in the detecting current of PAPF or not. Also the PAPF with proposed method has strong ability in harmonic compensation. Finally, the experiment results are presented to verify the analysis....

Sensing Methods for Detecting Analog Television Signals

Science.gov (United States)

Rahman, Mohammad Azizur; Song, Chunyi; Harada, Hiroshi

This paper introduces a unified method of spectrum sensing for all existing analog television (TV) signals including NTSC, PAL and SECAM. We propose a correlation based method (CBM) with a single reference signal for sensing any analog TV signals. In addition we also propose an improved energy detection method. The CBM approach has been implemented in a hardware prototype specially designed for participating in Singapore TV white space (WS) test trial conducted by Infocomm Development Authority (IDA) of the Singapore government. Analytical and simulation results of the CBM method will be presented in the paper, as well as hardware testing results for sensing various analog TV signals. Both AWGN and fading channels will be considered. It is shown that the theoretical results closely match with those from simulations. Sensing performance of the hardware prototype will also be presented in fading environment by using a fading simulator. We present performance of the proposed techniques in terms of probability of false alarm, probability of detection, sensing time etc. We also present a comparative study of the various techniques.

Atmospheric pollution problems and control proposals associated with solid waste management in China: A review

International Nuclear Information System (INIS)

Tian, Hezhong; Gao, Jiajia; Hao, Jiming; Lu, Long; Zhu, Chuanyong; Qiu, Peipei

2013-01-01

Highlights: ► Air pollution problems generated in MSW management processes in China are presented. ► Both quantity and composition of MSW generation in China are identified. ► The status of different methods for MSW treatment and disposal are reviewed. ► Some comprehensive control proposals for improving MSW management are proposed. -- Abstract: Along with population growth, rapid urbanization and industrialization process, the volume of municipal solid waste (MSW) generation in China has been increasing sharply in the past 30 years and the total amount of MSW yields will continue to increase. Nowadays, due to global warming warrants particular attention throughout the world, a series of air pollutants (including greenhouse gases, odorous gases, PCDD/Fs, heavy metals, PM, etc.) discharged from waste disposal and treatment processes have become one of the new significant emerging air pollution sources, which arousing great concerns about their adverse effects on surrounding ambient air quality and public health. At present, the overall safely disposed ratio of the collected MSW in China is reported at approximately 78% in 2010, and there are mainly three types of MSW disposal methods practiced in China, including landfill, composting and incineration. The characteristics of air pollutants and greenhouse gases discharge vary substantially among different MSW disposal methods. By presenting a thorough review of MSW generation in China and providing a summarization of the current status of MSW disposal methods practices, this review article makes an integrated overview analysis of existing air pollution problems associated with MSW collection, separation, and disposal processes. Furthermore, some comprehensive control proposals to prevent air pollution for improving MSW management of China in the future are put forward

Atmospheric pollution problems and control proposals associated with solid waste management in China: A review

Energy Technology Data Exchange (ETDEWEB)

Tian, Hezhong, E-mail: hztian@bnu.edu.cn [State Key Joint Laboratory of Environmental Simulation and Pollution Control, School of Environment, Beijing Normal University, Beijing 100875 (China); Gao, Jiajia [State Key Joint Laboratory of Environmental Simulation and Pollution Control, School of Environment, Beijing Normal University, Beijing 100875 (China); Hao, Jiming [School of Environment, Tsinghua University, Beijing 100084 (China); Lu, Long; Zhu, Chuanyong; Qiu, Peipei [State Key Joint Laboratory of Environmental Simulation and Pollution Control, School of Environment, Beijing Normal University, Beijing 100875 (China)

2013-05-15

Highlights: ► Air pollution problems generated in MSW management processes in China are presented. ► Both quantity and composition of MSW generation in China are identified. ► The status of different methods for MSW treatment and disposal are reviewed. ► Some comprehensive control proposals for improving MSW management are proposed. -- Abstract: Along with population growth, rapid urbanization and industrialization process, the volume of municipal solid waste (MSW) generation in China has been increasing sharply in the past 30 years and the total amount of MSW yields will continue to increase. Nowadays, due to global warming warrants particular attention throughout the world, a series of air pollutants (including greenhouse gases, odorous gases, PCDD/Fs, heavy metals, PM, etc.) discharged from waste disposal and treatment processes have become one of the new significant emerging air pollution sources, which arousing great concerns about their adverse effects on surrounding ambient air quality and public health. At present, the overall safely disposed ratio of the collected MSW in China is reported at approximately 78% in 2010, and there are mainly three types of MSW disposal methods practiced in China, including landfill, composting and incineration. The characteristics of air pollutants and greenhouse gases discharge vary substantially among different MSW disposal methods. By presenting a thorough review of MSW generation in China and providing a summarization of the current status of MSW disposal methods practices, this review article makes an integrated overview analysis of existing air pollution problems associated with MSW collection, separation, and disposal processes. Furthermore, some comprehensive control proposals to prevent air pollution for improving MSW management of China in the future are put forward.

Proposal for element size and time increment selection guideline by 3-D finite element method for elastic waves propagation analysis

International Nuclear Information System (INIS)

Ishida, Hitoshi; Meshii, Toshiyuki

2008-01-01

This paper proposes a guideline for selection of element size and time increment by 3-D finite element method, which is applied to elastic wave propagation analysis for a long distance of a large structure. An element size and a time increment are determined by quantitative evaluation of strain, which must be 0 on the analysis model with a uniform motion, caused by spatial and time discretization. (author)

Object-Based Dense Matching Method for Maintaining Structure Characteristics of Linear Buildings.

Science.gov (United States)

Su, Nan; Yan, Yiming; Qiu, Mingjie; Zhao, Chunhui; Wang, Liguo

2018-03-29

In this paper, we proposed a novel object-based dense matching method specially for the high-precision disparity map of building objects in urban areas, which can maintain accurate object structure characteristics. The proposed framework mainly includes three stages. Firstly, an improved edge line extraction method is proposed for the edge segments to fit closely to building outlines. Secondly, a fusion method is proposed for the outlines under the constraint of straight lines, which can maintain the building structural attribute with parallel or vertical edges, which is very useful for the dense matching method. Finally, we proposed an edge constraint and outline compensation (ECAOC) dense matching method to maintain building object structural characteristics in the disparity map. In the proposed method, the improved edge lines are used to optimize matching search scope and matching template window, and the high-precision building outlines are used to compensate the shape feature of building objects. Our method can greatly increase the matching accuracy of building objects in urban areas, especially at building edges. For the outline extraction experiments, our fusion method verifies the superiority and robustness on panchromatic images of different satellites and different resolutions. For the dense matching experiments, our ECOAC method shows great advantages for matching accuracy of building objects in urban areas compared with three other methods.

Object-Based Dense Matching Method for Maintaining Structure Characteristics of Linear Buildings

Directory of Open Access Journals (Sweden)

Nan Su

2018-03-01

Full Text Available In this paper, we proposed a novel object-based dense matching method specially for the high-precision disparity map of building objects in urban areas, which can maintain accurate object structure characteristics. The proposed framework mainly includes three stages. Firstly, an improved edge line extraction method is proposed for the edge segments to fit closely to building outlines. Secondly, a fusion method is proposed for the outlines under the constraint of straight lines, which can maintain the building structural attribute with parallel or vertical edges, which is very useful for the dense matching method. Finally, we proposed an edge constraint and outline compensation (ECAOC dense matching method to maintain building object structural characteristics in the disparity map. In the proposed method, the improved edge lines are used to optimize matching search scope and matching template window, and the high-precision building outlines are used to compensate the shape feature of building objects. Our method can greatly increase the matching accuracy of building objects in urban areas, especially at building edges. For the outline extraction experiments, our fusion method verifies the superiority and robustness on panchromatic images of different satellites and different resolutions. For the dense matching experiments, our ECOAC method shows great advantages for matching accuracy of building objects in urban areas compared with three other methods.

Voluntary transmission access: The PSI proposal

International Nuclear Information System (INIS)

Norris, J.E.

1990-01-01

This article examines a proposal from PSI Energy, Inc. (formerly Public Service Company of Indiana) to allow open access to its power transmission facilities and the response of the Federal Energy Regulatory Commission's response to that proposal. The topics discussed include transmission tariffs, competition, market share, expansion of transmission capacity and its funding, and reciprocal agreements to provide similar service

Joint Spatio-Temporal Filtering Methods for DOA and Fundamental Frequency Estimation

DEFF Research Database (Denmark)

Jensen, Jesper Rindom; Christensen, Mads Græsbøll; Benesty, Jacob

2015-01-01

some attention in the community and is quite promising for several applications. The proposed methods are based on optimal, adaptive filters that leave the desired signal, having a certain DOA and fundamental frequency, undistorted and suppress everything else. The filtering methods simultaneously...... operate in space and time, whereby it is possible resolve cases that are otherwise problematic for pitch estimators or DOA estimators based on beamforming. Several special cases and improvements are considered, including a method for estimating the covariance matrix based on the recently proposed...

Trends and regional variations in provision of contraception methods in a commercially insured population in the United States based on nationally proposed measures.

Science.gov (United States)

Law, A; Yu, J S; Wang, W; Lin, J; Lynen, R

2017-09-01

Three measures to assess the provision of effective contraception methods among reproductive-aged women have recently been endorsed for national public reporting. Based on these measures, this study examined real-world trends and regional variations of contraceptive provision in a commercially insured population in the United States. Women 15-44years old with continuous enrollment in each year from 2005 to 2014 were identified from a commercial claims database. In accordance with the proposed measures, percentages of women (a) provided most effective or moderately effective (MEME) methods of contraception and (b) provided a long-acting reversible contraceptive (LARC) method were calculated in two populations: women at risk for unintended pregnancy and women who had a live birth within 3 and 60days of delivery. During the 10-year period, the percentages of women at risk for unintended pregnancy provided MEME contraceptive methods increased among 15-20-year-olds (24.5%-35.9%) and 21-44-year-olds (26.2%-31.5%), and those provided a LARC method also increased among 15-20-year-olds (0.1%-2.4%) and 21-44-year-olds (0.8%-3.9%). Provision of LARC methods increased most in the North Central and West among both age groups of women. Provision of MEME contraceptives and LARC methods to women who had a live birth within 60days postpartum also increased across age groups and regions. This assessment indicates an overall trend of increasing provision of MEME contraceptive methods in the commercial sector, albeit with age group and regional variations. If implemented, these proposed measures may have impacts on health plan contraceptive access policy. Copyright © 2017 Elsevier Inc. All rights reserved.

Summary Report of Laboratory Testing to Establish the Effectiveness of Proposed Treatment Methods for Unremediated and Remediated Nitrate Salt Waste Streams

Energy Technology Data Exchange (ETDEWEB)

Anast, Kurt Roy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Funk, David John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-05-12

The inadvertent creation of transuranic waste carrying hazardous waste codes D001 and D002 requires the treatment of the material to eliminate the hazardous characteristics and allow its eventual shipment and disposal at the Waste Isolation Pilot Plant (WIPP). This report documents the effectiveness of two treatment methods proposed to stabilize both the unremediated and remediated nitrate salt waste streams (UNS and RNS, respectively). The two technologies include the addition of zeolite (with and without the addition of water as a processing aid) and cementation. Surrogates were developed to evaluate both the solid and liquid fractions expected from parent waste containers, and both the solid and liquid fractions were tested. Both technologies are shown to be effective at eliminating the characteristic of ignitability (D001), and the addition of zeolite was determined to be effective at eliminating corrosivity (D002), with the preferred option1 of zeolite addition currently planned for implementation at the Waste Characterization, Reduction, and Repackaging Facility. During the course of this work, we established the need to evaluate and demonstrate the effectiveness of the proposed remedy for debris material, if required. The evaluation determined that Wypalls absorbed with saturated nitrate salt solutions exhibit the ignitability characteristic (all other expected debris is not classified as ignitable). Follow-on studies will be developed to demonstrate the effectiveness of stabilization for ignitable Wypall debris. Finally, liquid surrogates containing saturated nitrate salts did not exhibit the characteristic of ignitability in their pure form (those neutralized with Kolorsafe and mixed with sWheat did exhibit D001). As a result, additional nitrate salt solutions (those exhibiting the oxidizer characteristic) will be tested to demonstrate the effectiveness of the remedy.

Measure Guideline: Summary of Interior Ducts in New Construction, Including an Efficient, Affordable Method to Install Fur-Down Interior Ducts

Energy Technology Data Exchange (ETDEWEB)

Beal, D.; McIlvaine , J.; Fonorow, K.; Martin, E.

2011-11-01

This document illustrates guidelines for the efficient installation of interior duct systems in new housing, including the fur-up chase method, the fur-down chase method, and interior ducts positioned in sealed attics or sealed crawl spaces. This document illustrates guidelines for the efficient installation of interior duct systems in new housing. Interior ducts result from bringing the duct work inside a home's thermal and air barrier. Architects, designers, builders, and new home buyers should thoroughly investigate any opportunity for energy savings that is as easy to implement during construction, such as the opportunity to construct interior duct work. In addition to enhanced energy efficiency, interior ductwork results in other important advantages, such as improved indoor air quality, increased system durability and increased homeowner comfort. While the advantages of well-designed and constructed interior duct systems are recognized, the implementation of this approach has not gained a significant market acceptance. This guideline describes a variety of methods to create interior ducts including the fur-up chase method, the fur-down chase method, and interior ducts positioned in sealed attics or sealed crawl spaces. As communication of the intent of an interior duct system, and collaboration on its construction are paramount to success, this guideline details the critical design, planning, construction, inspection, and verification steps that must be taken. Involved in this process are individuals from the design team; sales/marketing team; and mechanical, insulation, plumbing, electrical, framing, drywall and solar contractors.

Solving the competitive facility location problem considering the reactions of competitor with a hybrid algorithm including Tabu Search and exact method

Science.gov (United States)

Bagherinejad, Jafar; Niknam, Azar

2018-03-01

In this paper, a leader-follower competitive facility location problem considering the reactions of the competitors is studied. A model for locating new facilities and determining levels of quality for the facilities of the leader firm is proposed. Moreover, changes in the location and quality of existing facilities in a competitive market where a competitor offers the same goods or services are taken into account. The competitor could react by opening new facilities, closing existing ones, and adjusting the quality levels of its existing facilities. The market share, captured by each facility, depends on its distance to customer and its quality that is calculated based on the probabilistic Huff's model. Each firm aims to maximize its profit subject to constraints on quality levels and budget of setting up new facilities. This problem is formulated as a bi-level mixed integer non-linear model. The model is solved using a combination of Tabu Search with an exact method. The performance of the proposed algorithm is compared with an upper bound that is achieved by applying Karush-Kuhn-Tucker conditions. Computational results show that our algorithm finds near the upper bound solutions in a reasonable time.

New Jersey proposes rule reducing NOx emissions

International Nuclear Information System (INIS)

Anon.

1993-01-01

The New Jersey Department of Environmental Protection and Energy has proposed a rule requiring utility and industrial sources to significantly reduce their emission levels of nitrogen oxide (NO x ). If approved, it will be the first major rule mandated by the Clean Air Act Amendments of 1990 to affect New Jersey's stationary sources of these air pollutants - primarily electric generating utilities and other large fossil fuel burning facilities. The proposed rule requires all facilities with the potential to emit 25 tons or more of NO x each year to install reasonably available control technology by May 30, 1995. According to Richard Sinding, the environment and energy agency's assistant commissioner for policy and planning, the rule will likely require installation of low-NO x burners or other modifications to the combustion process. Sinding says the proposed rule will reduce the State's NO x emissions by approximately 30,000 tons a year, roughly 30 percent from current levels from these stationary sources. The pollution prevention measures are estimated to cost approximately $1,000 for each ton of NO x removed. The state energy agency estimates the average residential utility customer will see an increase in the monthly electric bill of about 50 cents. The agency said the proposed regulation includes provisions to make implementation more flexible and less costly for achieving the NO x reductions. It has approved the use of natural gas during the ozone season if low-NO x burners are not available. Additionally, emissions may be averaged from all units at the same utility or company location, effectively allowing a company to select the most cost-effective method of achieving the required emissions reductions

40 CFR 57.602 - Approval of proposal.

Science.gov (United States)

2010-07-01

... § 57.603. The application shall also specify: (1) The design and substantive elements of the research...) The smelter owner's proposal. The smelter owner's NSO application shall include a proposed NSO... agency is that the planned work must yield the most cost effective technology possible. (c) Optional...

Assessment of health-care waste disposal methods using a VIKOR-based fuzzy multi-criteria decision making method

Energy Technology Data Exchange (ETDEWEB)

Liu, Hu-Chen [School of Management, Hefei University of Technology, Hefei 230009 (China); Department of Industrial Engineering and Management, Tokyo Institute of Technology, Tokyo 152-8552 (Japan); Wu, Jing [Department of Public Management, Tongji University, Shanghai 200092 (China); Li, Ping, E-mail: yiwuchulp@126.com [Shanghai Pudong New Area Zhoupu Hospital, No. 135 Guanyue Road, Shanghai 201318 (China); East Hospital Affiliated to Tongji University, No. 150 Jimo Road, Shanghai 200120 (China)

2013-12-15

Highlights: • Propose a VIKOR-based fuzzy MCDM technique for evaluating HCW disposal methods. • Linguistic variables are used to assess the ratings and weights for the criteria. • The OWA operator is utilized to aggregate individual opinions of decision makers. • A case study is given to illustrate the procedure of the proposed framework. - Abstract: Nowadays selection of the appropriate treatment method in health-care waste (HCW) management has become a challenge task for the municipal authorities especially in developing countries. Assessment of HCW disposal alternatives can be regarded as a complicated multi-criteria decision making (MCDM) problem which requires consideration of multiple alternative solutions and conflicting tangible and intangible criteria. The objective of this paper is to present a new MCDM technique based on fuzzy set theory and VIKOR method for evaluating HCW disposal methods. Linguistic variables are used by decision makers to assess the ratings and weights for the established criteria. The ordered weighted averaging (OWA) operator is utilized to aggregate individual opinions of decision makers into a group assessment. The computational procedure of the proposed framework is illustrated through a case study in Shanghai, one of the largest cities of China. The HCW treatment alternatives considered in this study include “incineration”, “steam sterilization”, “microwave” and “landfill”. The results obtained using the proposed approach are analyzed in a comparative way.

Assessment of health-care waste disposal methods using a VIKOR-based fuzzy multi-criteria decision making method

International Nuclear Information System (INIS)

Liu, Hu-Chen; Wu, Jing; Li, Ping

2013-01-01

Highlights: • Propose a VIKOR-based fuzzy MCDM technique for evaluating HCW disposal methods. • Linguistic variables are used to assess the ratings and weights for the criteria. • The OWA operator is utilized to aggregate individual opinions of decision makers. • A case study is given to illustrate the procedure of the proposed framework. - Abstract: Nowadays selection of the appropriate treatment method in health-care waste (HCW) management has become a challenge task for the municipal authorities especially in developing countries. Assessment of HCW disposal alternatives can be regarded as a complicated multi-criteria decision making (MCDM) problem which requires consideration of multiple alternative solutions and conflicting tangible and intangible criteria. The objective of this paper is to present a new MCDM technique based on fuzzy set theory and VIKOR method for evaluating HCW disposal methods. Linguistic variables are used by decision makers to assess the ratings and weights for the established criteria. The ordered weighted averaging (OWA) operator is utilized to aggregate individual opinions of decision makers into a group assessment. The computational procedure of the proposed framework is illustrated through a case study in Shanghai, one of the largest cities of China. The HCW treatment alternatives considered in this study include “incineration”, “steam sterilization”, “microwave” and “landfill”. The results obtained using the proposed approach are analyzed in a comparative way

Robust sleep quality quantification method for a personal handheld device.

Science.gov (United States)

Shin, Hangsik; Choi, Byunghun; Kim, Doyoon; Cho, Jaegeol

2014-06-01

The purpose of this study was to develop and validate a novel method for sleep quality quantification using personal handheld devices. The proposed method used 3- or 6-axes signals, including acceleration and angular velocity, obtained from built-in sensors in a smartphone and applied a real-time wavelet denoising technique to minimize the nonstationary noise. Sleep or wake status was decided on each axis, and the totals were finally summed to calculate sleep efficiency (SE), regarded as sleep quality in general. The sleep experiment was carried out for performance evaluation of the proposed method, and 14 subjects participated. An experimental protocol was designed for comparative analysis. The activity during sleep was recorded not only by the proposed method but also by well-known commercial applications simultaneously; moreover, activity was recorded on different mattresses and locations to verify the reliability in practical use. Every calculated SE was compared with the SE of a clinically certified medical device, the Philips (Amsterdam, The Netherlands) Actiwatch. In these experiments, the proposed method proved its reliability in quantifying sleep quality. Compared with the Actiwatch, accuracy and average bias error of SE calculated by the proposed method were 96.50% and -1.91%, respectively. The proposed method was vastly superior to other comparative applications with at least 11.41% in average accuracy and at least 6.10% in average bias; average accuracy and average absolute bias error of comparative applications were 76.33% and 17.52%, respectively.

48 CFR 715.305 - Proposal evaluation.

Science.gov (United States)

2010-10-01

... CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Source Selection 715.305 Proposal evaluation... perceive no actual or potential conflict of interests. (An acceptable certification appears under ADS...

Proposal for an ecoradiological centre model

International Nuclear Information System (INIS)

Perovic, S.M.; Zunic, Z.; Demajo, M.; Konjevic, N.

1998-01-01

The problem of establishing an optimal Ecoradiological Centre Model is studied in some detail for the town of Kotor which is under the protection of the World Cultural and Natural Heritage. The proposed structure of the Centre is analyzed from the view of Engineering, Education and Scientific parameters. This Model is suitable for implementation as a network Centre Model for the state of Montenegro. Further, the modelling strategy of the ecoradiological condition control of natural, construction, bio and technological systems is elaborated. The proposal includes the ecoradiological monitoring, radioactive and electromagnetic radiation processing and protection for different natural zones as well as their different geostructures, aerial and hydrogeological conditions. The programme also includes all housing objects (hotels, flats, houses, office premises etc.). Here will also be presented the radiation protection and recommendations for the implementation of Title VII of the European Basic Safety Standards Directive (BSS), concerning significant increase in exposure due to natural radiation sources. Also, the proposal of Local Radiation Protection for the town of Kotor is presented. Our proposal for an Ecoradiological Centre Model presented here is in a form of a pilot programme, applicable also for other towns and states. (author)

Applications of the conjugate gradient FFT method in scattering and radiation including simulations with impedance boundary conditions

Science.gov (United States)

Barkeshli, Kasra; Volakis, John L.

1991-01-01

The theoretical and computational aspects related to the application of the Conjugate Gradient FFT (CGFFT) method in computational electromagnetics are examined. The advantages of applying the CGFFT method to a class of large scale scattering and radiation problems are outlined. The main advantages of the method stem from its iterative nature which eliminates a need to form the system matrix (thus reducing the computer memory allocation requirements) and guarantees convergence to the true solution in a finite number of steps. Results are presented for various radiators and scatterers including thin cylindrical dipole antennas, thin conductive and resistive strips and plates, as well as dielectric cylinders. Solutions of integral equations derived on the basis of generalized impedance boundary conditions (GIBC) are also examined. The boundary conditions can be used to replace the profile of a material coating by an impedance sheet or insert, thus, eliminating the need to introduce unknown polarization currents within the volume of the layer. A general full wave analysis of 2-D and 3-D rectangular grooves and cavities is presented which will also serve as a reference for future work.

Integrated Reliability Estimation of a Nuclear Maintenance Robot including a Software

Energy Technology Data Exchange (ETDEWEB)

Eom, Heung Seop; Kim, Jae Hee; Jeong, Kyung Min [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2011-10-15

Conventional reliability estimation techniques such as Fault Tree Analysis (FTA), Reliability Block Diagram (RBD), Markov Model, and Event Tree Analysis (ETA) have been used widely and approved in some industries. Then there are some limitations when we use them for a complicate robot systems including software such as intelligent reactor inspection robots. Therefore an expert's judgment plays an important role in estimating the reliability of a complicate system in practice, because experts can deal with diverse evidence related to the reliability and then perform an inference based on them. The proposed method in this paper combines qualitative and quantitative evidences and performs an inference like experts. Furthermore, it does the work in a formal and in a quantitative way unlike human experts, by the benefits of Bayesian Nets (BNs)

PACMan to Help Sort Hubble Proposals

Science.gov (United States)

Kohler, Susanna

2017-04-01

Every year, astronomers submit over a thousand proposals requesting time on the Hubble Space Telescope (HST). Currently, humans must sort through each of these proposals by hand before sending them off for review. Could this burden be shifted to computers?A Problem of VolumeAstronomer Molly Peeples gathered stats on the HST submissions sent in last week for the upcoming HST Cycle 25 (the deadline was Friday night), relative to previous years. This years proposal round broke the record, with over 1200 proposals submitted in total for Cycle 25. [Molly Peeples]Each proposal cycle for HST time attracts on the order of 1100 proposals accounting for far more HST time than is available. The proposals are therefore carefully reviewed by around 150 international members of the astronomy community during a six-month process to select those with the highest scientific merit.Ideally, each proposal will be read by reviewers that have scientific expertise relevant to the proposal topic: if a proposal requests HST time to study star formation, for instance, then the reviewers assigned to it should have research expertise in star formation.How does this matching of proposals to reviewers occur? The current method relies on self-reported categorization of the submitted proposals. This is unreliable, however; proposals are often mis-categorized by submitters due to misunderstanding or ambiguous cases.As a result, the Science Policies Group at the Space Telescope Science Institute (STScI) which oversees the review of HST proposals must go through each of the proposals by hand and re-categorize them. The proposals are then matched to reviewers with self-declared expertise in the same category.With the number of HST proposals on the rise and the expectation that the upcoming James Webb Space Telescope (JWST) will elicit even more proposals for time than Hubble scientists at STScI and NASA are now asking: could the human hours necessary for this task be spared? Could a computer program

Proposed Terminology and Classification of Pre-Malignant Neoplastic Conditions: A Consensus Proposal

Directory of Open Access Journals (Sweden)

Peter Valent

2017-12-01

Full Text Available Cancer evolution is a step-wise non-linear process that may start early in life or later in adulthood, and includes pre-malignant (indolent and malignant phases. Early somatic changes may not be detectable or are found by chance in apparently healthy individuals. The same lesions may be detected in pre-malignant clonal conditions. In some patients, these lesions may never become relevant clinically whereas in others, they act together with additional pro-oncogenic hits and thereby contribute to the formation of an overt malignancy. Although some pre-malignant stages of a malignancy have been characterized, no global system to define and to classify these conditions is available. To discuss open issues related to pre-malignant phases of neoplastic disorders, a working conference was organized in Vienna in August 2015. The outcomes of this conference are summarized herein and include a basic proposal for a nomenclature and classification of pre-malignant conditions. This proposal should assist in the communication among patients, physicians and scientists, which is critical as genome-sequencing will soon be offered widely for early cancer-detection.

System and Method for Monitoring Distributed Asset Data

Science.gov (United States)

Gorinevsky, Dimitry (Inventor)

2015-01-01

A computer-based monitoring system and monitoring method implemented in computer software for detecting, estimating, and reporting the condition states, their changes, and anomalies for many assets. The assets are of same type, are operated over a period of time, and outfitted with data collection systems. The proposed monitoring method accounts for variability of working conditions for each asset by using regression model that characterizes asset performance. The assets are of the same type but not identical. The proposed monitoring method accounts for asset-to-asset variability; it also accounts for drifts and trends in the asset condition and data. The proposed monitoring system can perform distributed processing of massive amounts of historical data without discarding any useful information where moving all the asset data into one central computing system might be infeasible. The overall processing is includes distributed preprocessing data records from each asset to produce compressed data.

Curvature-Continuous 3D Path-Planning Using QPMI Method

Directory of Open Access Journals (Sweden)

Seong-Ryong Chang

2015-06-01

Full Text Available It is impossible to achieve vertex movement and rapid velocity control in aerial robots and aerial vehicles because of momentum from the air. A continuous-curvature path ensures such robots and vehicles can fly with stable and continuous movements. General continuous path-planning methods use spline interpolation, for example B-spline and Bézier curves. However, these methods cannot be directly applied to continuous path planning in a 3D space. These methods use a subset of the waypoints to decide curvature and some waypoints are not included in the planned path. This paper proposes a method for constructing a curvature-continuous path in 3D space that includes every waypoint. The movements in each axis, x, y and z, are separated by the parameter u. Waypoint groups are formed, each with its own continuous path derived using quadratic polynomial interpolation. The membership function then combines each continuous path into one continuous path. The continuity of the path is verified and the curvature-continuous path is produced using the proposed method.

A Proposal for a Methodology to Develop a Cyber-Attack Penetration Test Scenario Including NPPs Safety

Energy Technology Data Exchange (ETDEWEB)

Lee, In Hyo [KAIST, Daejeon (Korea, Republic of); Son, Han Seong [Joongbu Univ., Geumsan (Korea, Republic of); Kim, Si Won [Korea Institute of Nuclear Nonproliferation and Control, Daejeon (Korea, Republic of); Kang, Hyun Gook [Rensselaer Polytechnic Institute, Troy (United States)

2016-10-15

Penetration test is a method to evaluate the cyber security of NPPs; so, this approach was performed in some studies. Because they focused on vulnerability finding or test bed construction, scenario based approach was not performed. However, to test the cyber security of NPPs, a proper test scenario should be needed. Ahn et al. developed cyber-attack scenarios but those scenarios couldn't be applied in penetration test because they developed the scenarios based on past incidents of NPPs induced by cyber-attack. That is, those scenarios only covered scenarios which were happened before; so, they couldn't cover other various scenarios and couldn't reflect them into a penetration test. In this study, a method to develop a cyber-attack penetration test scenario of NPPs especially focused on safety point of view is suggested. To evaluate the cyber security of NPPs, penetration test can be a possible way. In this study, a method to develop a penetration test scenario was explained. Especially, the goal of hacker was focused on nuclear fuel integrity deterioration. So, in the methodology, Level 1 PSA results were utilized to reflect plant safety into the security. From the PSA results, basic event was post processed and possible cyber-attacks were reviewed with vulnerabilities of digital control system.

A Proposal for a Methodology to Develop a Cyber-Attack Penetration Test Scenario Including NPPs Safety

International Nuclear Information System (INIS)

Lee, In Hyo; Son, Han Seong; Kim, Si Won; Kang, Hyun Gook

2016-01-01

Penetration test is a method to evaluate the cyber security of NPPs; so, this approach was performed in some studies. Because they focused on vulnerability finding or test bed construction, scenario based approach was not performed. However, to test the cyber security of NPPs, a proper test scenario should be needed. Ahn et al. developed cyber-attack scenarios but those scenarios couldn't be applied in penetration test because they developed the scenarios based on past incidents of NPPs induced by cyber-attack. That is, those scenarios only covered scenarios which were happened before; so, they couldn't cover other various scenarios and couldn't reflect them into a penetration test. In this study, a method to develop a cyber-attack penetration test scenario of NPPs especially focused on safety point of view is suggested. To evaluate the cyber security of NPPs, penetration test can be a possible way. In this study, a method to develop a penetration test scenario was explained. Especially, the goal of hacker was focused on nuclear fuel integrity deterioration. So, in the methodology, Level 1 PSA results were utilized to reflect plant safety into the security. From the PSA results, basic event was post processed and possible cyber-attacks were reviewed with vulnerabilities of digital control system

Proposal for Testing and Validation of Vacuum Ultra-Violet Atomic Laser-Induced Fluorescence as a Method to Analyze Carbon Grid Erosion in Ion Thrusters

Science.gov (United States)

Stevens, Richard

2003-01-01

Previous investigation under award NAG3-25 10 sought to determine the best method of LIF to determine the carbon density in a thruster plume. Initial reports from other groups were ambiguous as to the number of carbon clusters that might be present in the plume of a thruster. Carbon clusters would certainly affect the ability to LIF; if they were the dominant species, then perhaps the LIF method should target clusters. The results of quadrupole mass spectroscopy on sputtered carbon determined that minimal numbers of clusters were sputtered from graphite under impact from keV Krypton. There were some investigations in the keV range by other groups that hinted at clusters, but at the time the proposal was presented to NASA, there was no data from low-energy sputtering available. Thus, the proposal sought to develop a method to characterize the population only of atoms sputtered from a graphite target in a test cell. Most of the ground work had been established by the previous two years of investigation. The proposal covering 2003 sought to develop an anti-Stokes Raman shifting cell to generate VUW light and test this cell on two different laser systems, ArF and YAG- pumped dye. The second goal was to measure the lowest detectable amounts of carbon atoms by 156.1 nm and 165.7 nm LIF. If equipment was functioning properly, it was expected that these goals would be met easily during the timeframe of the proposal, and that is the reason only modest funding was requested. The PI was only funded at half- time by Glenn during the summer months. All other work time was paid for by Whitworth College. The college also funded a student, Charles Shawley, who worked on the project during the spring.

15 CFR 2006.1 - Information to be included in petition.

Science.gov (United States)

2010-01-01

... property right, or foreign direct investment matter for which the rights of the United States under the... nature of any foreign direct investment proposed by the United States person, including estimates of... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Information to be included in petition...

Ex-ante participatory research proposal assessment conducted in Southern Togo

Directory of Open Access Journals (Sweden)

V. Deffo

2011-01-01

Full Text Available This study was conducted to showcase a participatory method for assessing technical options in Southern Togo. The aim was to address farmers’ needs with respect to soil fertility problems in situations involving mixed crop-livestock farming systems. In collaboration with various stakeholders, the scientists thus assessed the potential for adopting a crop association involving maize for food (seed and fodder (straw, i.e. a mixed function plant, and Mucuna pruriens, i.e. a long-cycle legume that is cropped to produce fodder and enhance soil fertility. The chemically fertilized crop association is here referred to as MME. Participatory action research (PAR analytical tools were implemented in the four-phase method used. The first phase included an overall description of the entire study region to identify representative sites based on published information and exploratory interviews. In the second phase, the diversity of farmers was characterized through interviews with resource people at the selected sites. The third phase involved participatory selection of a range of technical options that included the MME association as well as local practices with features similar to this association, and alternative research proposals to enhance soil fertility and ensure the production of sufficient fodder to feed livestock. This selection was carried out by farmers chosen as being representative of their diversity. They were asked to rank—using notes, or pebbles because of the high illiteracy level—the different technical options presented during visits to the test plots or using visual aids. The fourth phase included an assessment of farmers’ comments on the perceived effects of the different options on agropastoral resource management (water, soil, biodiversity, their acceptability or cost-effectiveness relative to the labor cost. This method was applied in three villages in southern Togo. Six main farmer categories were identified in these

The Profile of Creativity and Proposing Statistical Problem Quality Level Reviewed From Cognitive Style

Science.gov (United States)

Awi; Ahmar, A. S.; Rahman, A.; Minggi, I.; Mulbar, U.; Asdar; Ruslan; Upu, H.; Alimuddin; Hamda; Rosidah; Sutamrin; Tiro, M. A.; Rusli

2018-01-01

This research aims to reveal the profile about the level of creativity and the ability to propose statistical problem of students at Mathematics Education 2014 Batch in the State University of Makassar in terms of their cognitive style. This research uses explorative qualitative method by giving meta-cognitive scaffolding at the time of research. The hypothesis of research is that students who have field independent (FI) cognitive style in statistics problem posing from the provided information already able to propose the statistical problem that can be solved and create new data and the problem is already been included as a high quality statistical problem, while students who have dependent cognitive field (FD) commonly are still limited in statistics problem posing that can be finished and do not load new data and the problem is included as medium quality statistical problem.

An Integrated Method for Airfoil Optimization

Science.gov (United States)

Okrent, Joshua B.

Design exploration and optimization is a large part of the initial engineering and design process. To evaluate the aerodynamic performance of a design, viscous Navier-Stokes solvers can be used. However this method can prove to be overwhelmingly time consuming when performing an initial design sweep. Therefore, another evaluation method is needed to provide accurate results at a faster pace. To accomplish this goal, a coupled viscous-inviscid method is used. This thesis proposes an integrated method for analyzing, evaluating, and optimizing an airfoil using a coupled viscous-inviscid solver along with a genetic algorithm to find the optimal candidate. The method proposed is different from prior optimization efforts in that it greatly broadens the design space, while allowing the optimization to search for the best candidate that will meet multiple objectives over a characteristic mission profile rather than over a single condition and single optimization parameter. The increased design space is due to the use of multiple parametric airfoil families, namely the NACA 4 series, CST family, and the PARSEC family. Almost all possible airfoil shapes can be created with these three families allowing for all possible configurations to be included. This inclusion of multiple airfoil families addresses a possible criticism of prior optimization attempts since by only focusing on one airfoil family, they were inherently limiting the number of possible airfoil configurations. By using multiple parametric airfoils, it can be assumed that all reasonable airfoil configurations are included in the analysis and optimization and that a global and not local maximum is found. Additionally, the method used is amenable to customization to suit any specific needs as well as including the effects of other physical phenomena or design criteria and/or constraints. This thesis found that an airfoil configuration that met multiple objectives could be found for a given set of nominal

Measurement network design including traveltime determinations to minimize model prediction uncertainty

NARCIS (Netherlands)

Janssen, G.M.C.M.; Valstar, J.R.; Zee, van der S.E.A.T.M.

2008-01-01

Traveltime determinations have found increasing application in the characterization of groundwater systems. No algorithms are available, however, to optimally design sampling strategies including this information type. We propose a first-order methodology to include groundwater age or tracer arrival

Proposal to consistently apply the International Code of Nomenclature of Prokaryotes (ICNP) to names of the oxygenic photosynthetic bacteria (cyanobacteria), including those validly published under the International Code of Botanical Nomenclature (ICBN)/International Code of Nomenclature for algae, fungi and plants (ICN), and proposal to change Principle 2 of the ICNP.

Science.gov (United States)

Pinevich, Alexander V

2015-03-01

This taxonomic note was motivated by the recent proposal [Oren & Garrity (2014) Int J Syst Evol Microbiol 64, 309-310] to exclude the oxygenic photosynthetic bacteria (cyanobacteria) from the wording of General Consideration 5 of the International Code of Nomenclature of Prokaryotes (ICNP), which entails unilateral coverage of these prokaryotes by the International Code of Nomenclature for algae, fungi, and plants (ICN; formerly the International Code of Botanical Nomenclature, ICBN). On the basis of key viewpoints, approaches and rules in the systematics, taxonomy and nomenclature of prokaryotes it is reciprocally proposed to apply the ICNP to names of cyanobacteria including those validly published under the ICBN/ICN. For this purpose, a change to Principle 2 of the ICNP is proposed to enable validation of cyanobacterial names published under the ICBN/ICN rules. © 2015 IUMS.

Ethical considerations in malaria research proposal review: empirical evidence from 114 proposals submitted to an Ethics Committee in Thailand.

Science.gov (United States)

Adams, Pornpimon; Prakobtham, Sukanya; Limphattharacharoen, Chanthima; Vutikes, Pitchapa; Khusmith, Srisin; Pengsaa, Krisana; Wilairatana, Polrat; Kaewkungwal, Jaranit

2015-09-14

Malaria research is typically conducted in developing countries in areas of endemic disease. This raises specific ethical issues, including those related to local cultural concepts of health and disease, the educational background of study subjects, and principles of justice at the community and country level. Research Ethics Committees (RECs) are responsible for regulating the ethical conduct of research, but questions have been raised whether RECs facilitate or impede research, and about the quality of REC review itself. This study examines the review process for malaria research proposals submitted to the Ethics Committee of the Faculty of Tropical Medicine at Mahidol University, Thailand. Proposals for all studies submitted for review from January 2010 to December 2014 were included. Individual REC members' reviewing forms were evaluated. Ethical issues (e.g., scientific merit, risk-benefit, sample size, or informed-consent) raised in the forms were counted and analysed according to characteristics, including study classification/design, use of specimens, study site, and study population. All 114 proposals submitted during the study period were analysed, comprising biomedical studies (17 %), drug trials (13 %), laboratory studies (24 %) and epidemiological studies (46 %). They included multi-site (13 %) and international studies (4 %), and those involving minority populations (28 %), children (17 %) and pregnant women (7 %). Drug trials had the highest proportion of questions raised for most ethical issues, while issues concerning privacy and confidentiality tended to be highest for laboratory and epidemiology studies. Clarifications on ethical issues were requested by the ethics committee more for proposals involving new specimen collection. Studies involving stored data and specimens tended to attract more issues around privacy and confidentiality. Proposals involving minority populations were more likely to raise issues than those that did not

Design, Evaluation and Implementation of an Islanding Detection Method for a Micro-grid

Directory of Open Access Journals (Sweden)

Taiying Zheng

2018-02-01

Full Text Available Correct and fast detection of a micro-grid (MG islanding is essential to the MG since operation, control, and protection of the MG depend on its operating mode i.e., an interconnected mode or islanding mode. This study describes the design, evaluation and implementation of an islanding detection method for an MG, which includes a natural gas-fired generator, a doubly fed induction generator type wind generator, a photovoltaic generator, and some associated local loads. The proposed method is based on the instantaneous active and reactive powers at the point of common coupling (PCC of the MG. During the islanding mode, the instantaneous active and reactive powers at the PCC are constants, which depend on the voltage of the PCC and the impedance of the dedicated line. The performance of the proposed method is verified under various scenarios including islanding conditions for the different outputs of the MG, and fault conditions by varying the position, type, inception angle and resistance of the fault, using the PSCAD/EMTDC simulator. This paper also concludes by implementing proposed method into a TMS320C6701 digital signal processor. The results indicate that the proposed method successfully detects islanding for the MG in islanding conditions, and remains stable in fault conditions.

Swedish methane gas project: a proposal with three alternatives. Svenskt metangasprojekt: ett foerslag med tre alternativ

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

A proposal concerning a BIOGAS project is given. The proposal includes: (a) microbiological research on, e.g., needs for additives to optimize the process, influence of the content of dry substance, high rate digesters, one- or two-stage processing, temperature tolerance, pH regulation, pressure dependence, methods for process regulation, hygienics, foam-quenching; (b) construction of a test plant equipped with instruments for analysis and supervision; and (c) construction of prototype plants at a swine farm and at a slaughterhouse. Detailed budgets and schedules are given for the project at three different possible total costs.

Scalable parallel elastic-plastic finite element analysis using a quasi-Newton method with a balancing domain decomposition preconditioner

Science.gov (United States)

Yusa, Yasunori; Okada, Hiroshi; Yamada, Tomonori; Yoshimura, Shinobu

2018-04-01

A domain decomposition method for large-scale elastic-plastic problems is proposed. The proposed method is based on a quasi-Newton method in conjunction with a balancing domain decomposition preconditioner. The use of a quasi-Newton method overcomes two problems associated with the conventional domain decomposition method based on the Newton-Raphson method: (1) avoidance of a double-loop iteration algorithm, which generally has large computational complexity, and (2) consideration of the local concentration of nonlinear deformation, which is observed in elastic-plastic problems with stress concentration. Moreover, the application of a balancing domain decomposition preconditioner ensures scalability. Using the conventional and proposed domain decomposition methods, several numerical tests, including weak scaling tests, were performed. The convergence performance of the proposed method is comparable to that of the conventional method. In particular, in elastic-plastic analysis, the proposed method exhibits better convergence performance than the conventional method.

Adobe Boxes: Locating Object Proposals Using Object Adobes.

Science.gov (United States)

Fang, Zhiwen; Cao, Zhiguo; Xiao, Yang; Zhu, Lei; Yuan, Junsong

2016-09-01

Despite the previous efforts of object proposals, the detection rates of the existing approaches are still not satisfactory enough. To address this, we propose Adobe Boxes to efficiently locate the potential objects with fewer proposals, in terms of searching the object adobes that are the salient object parts easy to be perceived. Because of the visual difference between the object and its surroundings, an object adobe obtained from the local region has a high probability to be a part of an object, which is capable of depicting the locative information of the proto-object. Our approach comprises of three main procedures. First, the coarse object proposals are acquired by employing randomly sampled windows. Then, based on local-contrast analysis, the object adobes are identified within the enlarged bounding boxes that correspond to the coarse proposals. The final object proposals are obtained by converging the bounding boxes to tightly surround the object adobes. Meanwhile, our object adobes can also refine the detection rate of most state-of-the-art methods as a refinement approach. The extensive experiments on four challenging datasets (PASCAL VOC2007, VOC2010, VOC2012, and ILSVRC2014) demonstrate that the detection rate of our approach generally outperforms the state-of-the-art methods, especially with relatively small number of proposals. The average time consumed on one image is about 48 ms, which nearly meets the real-time requirement.

An improved EMD method for modal identification and a combined static-dynamic method for damage detection

Science.gov (United States)

Yang, Jinping; Li, Peizhen; Yang, Youfa; Xu, Dian

2018-04-01

Empirical mode decomposition (EMD) is a highly adaptable signal processing method. However, the EMD approach has certain drawbacks, including distortions from end effects and mode mixing. In the present study, these two problems are addressed using an end extension method based on the support vector regression machine (SVRM) and a modal decomposition method based on the characteristics of the Hilbert transform. The algorithm includes two steps: using the SVRM, the time series data are extended at both endpoints to reduce the end effects, and then, a modified EMD method using the characteristics of the Hilbert transform is performed on the resulting signal to reduce mode mixing. A new combined static-dynamic method for identifying structural damage is presented. This method combines the static and dynamic information in an equilibrium equation that can be solved using the Moore-Penrose generalized matrix inverse. The combination method uses the differences in displacements of the structure with and without damage and variations in the modal force vector. Tests on a four-story, steel-frame structure were conducted to obtain static and dynamic responses of the structure. The modal parameters are identified using data from the dynamic tests and improved EMD method. The new method is shown to be more accurate and effective than the traditional EMD method. Through tests with a shear-type test frame, the higher performance of the proposed static-dynamic damage detection approach, which can detect both single and multiple damage locations and the degree of the damage, is demonstrated. For structures with multiple damage, the combined approach is more effective than either the static or dynamic method. The proposed EMD method and static-dynamic damage detection method offer improved modal identification and damage detection, respectively, in structures.

A rule-based automatic sleep staging method.

Science.gov (United States)

Liang, Sheng-Fu; Kuo, Chin-En; Hu, Yu-Han; Cheng, Yu-Shian

2012-03-30

In this paper, a rule-based automatic sleep staging method was proposed. Twelve features including temporal and spectrum analyses of the EEG, EOG, and EMG signals were utilized. Normalization was applied to each feature to eliminating individual differences. A hierarchical decision tree with fourteen rules was constructed for sleep stage classification. Finally, a smoothing process considering the temporal contextual information was applied for the continuity. The overall agreement and kappa coefficient of the proposed method applied to the all night polysomnography (PSG) of seventeen healthy subjects compared with the manual scorings by R&K rules can reach 86.68% and 0.79, respectively. This method can integrate with portable PSG system for sleep evaluation at-home in the near future. Copyright © 2012 Elsevier B.V. All rights reserved.

Referral system in rural Iran: improvement proposals

Directory of Open Access Journals (Sweden)

Mansour Naseriasl

2018-03-01

Full Text Available Because of insufficient communication between primary health care providers and specialists, which leads to inefficiencies and ineffectiveness in rural population health outcomes, to implement a well-functioning referral system is one of the most important tasks for some countries. Using purposive and snowballing sampling methods, we included health experts, policy-makers, family physicians, clinical specialists, and experts from health insurance organizations in this study according to pre-determined criteria. We recorded all interviews, transcribed and analyzed their content using qualitative methods. We extracted 1,522 individual codes initially. We also collected supplementary data through document review. From reviews and summarizations, four main themes, ten subthemes, and 24 issues emerged from the data. The solutions developed were: care system reform, education system reform, payment system reform, and improves in culture-building and public education. Given the executive experience, the full familiarity, the occupational and geographical diversity of participants, the solutions proposed in this study could positively affect the implementation and improvement of the referral system in Iran. The suggested solutions are complementary to each other and have less interchangeability.

Clinical target volume delineation including elective nodal irradiation in preoperative and definitive radiotherapy of pancreatic cancer

Directory of Open Access Journals (Sweden)

Caravatta Luciana

2012-06-01

Full Text Available Abstract Background Radiotherapy (RT is widely used in the treatment of pancreatic cancer. Currently, recommendation has been given for the delineation of the clinical target volume (CTV in adjuvant RT. Based on recently reviewed pathologic data, the aim of this study is to propose criteria for the CTV definition and delineation including elective nodal irradiation (ENI in the preoperative and definitive treatment of pancreatic cancer. Methods The anatomical structures of interest, as well as the abdominal vasculature were identified on intravenous contrast-enhanced CT scans of two different patients with pancreatic cancer of the head and the body. To delineate the lymph node area, a margin of 10 mm was added to the arteries. Results We proposed a set of guidelines for elective treatment of high-risk nodal areas and CTV delineation. Reference CT images were provided. Conclusions The proposed guidelines could be used for preoperative or definitive RT for carcinoma of the head and body of the pancreas. Further clinical investigations are needed to validate the defined CTVs.

SU-F-J-142: Proposed Method to Broaden Inclusion Potential of Patients Able to Use the Calypso Tracking System in Prostate Radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Fiedler, D; Kuo, H; Bodner, W; Tome, W [Montefiore Medical Center, Bronx, NY (United States)

2016-06-15

Purpose: To introduce a non-standard method of patient setup, using BellyBoard immobilization, to better utilize the localization and tracking potential of an RF-beacon system with EBRT for prostate cancer. Methods: An RF-beacon phantom was imaged using a wide bore CT scanner, both in a standard level position and with a known rotation (4° pitch and 7.5° yaw). A commercial treatment planning system (TPS) was used to determine positional coordinates of each beacon, and the centroid of the three beacons for both setups. For each setup at the Linac, kV AP and Rt Lateral images were obtained. A full characterization of the RF-beacon system in clinical mode was completed for various beacons’ array-to-centroid distances, which includes vertical, lateral, and longitudinal offset data, as well as pitch and yaw offset measurements for the tilted phantom. For the single patient who has been setup using the proposed BellyBoard method, a supine simulation was first obtained. When abdominal protrusion was found to be exceeding the limits of the RF-Beacon system through distance-based analysis in the TPS, the patient is re-simulated prone with the BellyBoard. Array to centroid distance is measured again in the TPS, and if found to be within the localization or tracking region it is applied. Results: Characterization of limitations for the RF-beacon system in clinical mode showed acceptable consistency of offset determination for phantom setup accuracy. The nonstandard patient setup method reduced the beacons’ centroid-to-array distance by 8.32cm, from 25.13cm to 16.81cm; completely out of tracking range (greater than 20cm) to within setup tracking range (less than 20cm). Conclusion: Using the RF-beacon system in combination with this novel patient setup can allow patients who would otherwise not be candidates for beacon enhanced EBRT to now be able to benefit from the reduced PTV margins of this treatment method.

SU-F-J-142: Proposed Method to Broaden Inclusion Potential of Patients Able to Use the Calypso Tracking System in Prostate Radiotherapy

International Nuclear Information System (INIS)

Fiedler, D; Kuo, H; Bodner, W; Tome, W

2016-01-01

Purpose: To introduce a non-standard method of patient setup, using BellyBoard immobilization, to better utilize the localization and tracking potential of an RF-beacon system with EBRT for prostate cancer. Methods: An RF-beacon phantom was imaged using a wide bore CT scanner, both in a standard level position and with a known rotation (4° pitch and 7.5° yaw). A commercial treatment planning system (TPS) was used to determine positional coordinates of each beacon, and the centroid of the three beacons for both setups. For each setup at the Linac, kV AP and Rt Lateral images were obtained. A full characterization of the RF-beacon system in clinical mode was completed for various beacons’ array-to-centroid distances, which includes vertical, lateral, and longitudinal offset data, as well as pitch and yaw offset measurements for the tilted phantom. For the single patient who has been setup using the proposed BellyBoard method, a supine simulation was first obtained. When abdominal protrusion was found to be exceeding the limits of the RF-Beacon system through distance-based analysis in the TPS, the patient is re-simulated prone with the BellyBoard. Array to centroid distance is measured again in the TPS, and if found to be within the localization or tracking region it is applied. Results: Characterization of limitations for the RF-beacon system in clinical mode showed acceptable consistency of offset determination for phantom setup accuracy. The nonstandard patient setup method reduced the beacons’ centroid-to-array distance by 8.32cm, from 25.13cm to 16.81cm; completely out of tracking range (greater than 20cm) to within setup tracking range (less than 20cm). Conclusion: Using the RF-beacon system in combination with this novel patient setup can allow patients who would otherwise not be candidates for beacon enhanced EBRT to now be able to benefit from the reduced PTV margins of this treatment method.

Contributors to Frequent Telehealth Alerts Including False Alerts for Patients with Heart Failure: A Mixed Methods Exploration

Science.gov (United States)

Radhakrishna, K.; Bowles, K.; Zettek-Sumner, A.

2013-01-01

Summary Background Telehealth data overload through high alert generation is a significant barrier to sustained adoption of telehealth for managing HF patients. Objective To explore the factors contributing to frequent telehealth alerts including false alerts for Medicare heart failure (HF) patients admitted to a home health agency. Materials and Methods A mixed methods design that combined quantitative correlation analysis of patient characteristic data with number of telehealth alerts and qualitative analysis of telehealth and visiting nurses’ notes on follow-up actions to patients’ telehealth alerts was employed. All the quantitative and qualitative data was collected through retrospective review of electronic records of the home heath agency. Results Subjects in the study had a mean age of 83 (SD = 7.6); 56% were female. Patient co-morbidities (ppatient characteristics along with establishing patient-centered telehealth outcome goals may allow meaningful generation of telehealth alerts. Reducing avoidable telehealth alerts could vastly improve the efficiency and sustainability of telehealth programs for HF management. PMID:24454576

Methods for computing color anaglyphs

Science.gov (United States)

McAllister, David F.; Zhou, Ya; Sullivan, Sophia

2010-02-01

A new computation technique is presented for calculating pixel colors in anaglyph images. The method depends upon knowing the RGB spectral distributions of the display device and the transmission functions of the filters in the viewing glasses. It requires the solution of a nonlinear least-squares program for each pixel in a stereo pair and is based on minimizing color distances in the CIEL*a*b* uniform color space. The method is compared with several techniques for computing anaglyphs including approximation in CIE space using the Euclidean and Uniform metrics, the Photoshop method and its variants, and a method proposed by Peter Wimmer. We also discuss the methods of desaturation and gamma correction for reducing retinal rivalry.

Method Points: towards a metric for method complexity

Directory of Open Access Journals (Sweden)

Graham McLeod

1998-11-01

Full Text Available A metric for method complexity is proposed as an aid to choosing between competing methods, as well as in validating the effects of method integration or the products of method engineering work. It is based upon a generic method representation model previously developed by the author and adaptation of concepts used in the popular Function Point metric for system size. The proposed technique is illustrated by comparing two popular I.E. deliverables with counterparts in the object oriented Unified Modeling Language (UML. The paper recommends ways to improve the practical adoption of new methods.

An Optimal Calibration Method for a MEMS Inertial Measurement Unit

Directory of Open Access Journals (Sweden)

Bin Fang

2014-02-01

Full Text Available An optimal calibration method for a micro-electro-mechanical inertial measurement unit (MIMU is presented in this paper. The accuracy of the MIMU is highly dependent on calibration to remove the deterministic errors of systematic errors, which also contain random errors. The overlapping Allan variance is applied to characterize the types of random error terms in the measurements. The calibration model includes package misalignment error, sensor-to-sensor misalignment error and bias, and a scale factor is built. The new concept of a calibration method, which includes a calibration scheme and a calibration algorithm, is proposed. The calibration scheme is designed by D-optimal and the calibration algorithm is deduced by a Kalman filter. In addition, the thermal calibration is investigated, as the bias and scale factor varied with temperature. The simulations and real tests verify the effectiveness of the proposed calibration method and show that it is better than the traditional method.

A proposed method for accurate 3D analysis of cochlear implant migration using fusion of cone beam CT

Directory of Open Access Journals (Sweden)

Guido eDees

2016-01-01

Full Text Available IntroductionThe goal of this investigation was to compare fusion of sequential cone beam CT volumes to the gold standard (fiducial registration in order to be able to analyze clinical CI migration with high accuracy in three dimensions. Materials and MethodsPaired time-lapsed cone beam CT volumes were performed on five human cadaver temporal bones and one human subject. These volumes were fused using 3D Slicer 4 and BRAINSFit software. Using a gold standard fiducial technique, the accuracy, robustness and performance time of the fusion process were assessed.Results This proposed fusion protocol achieves a sub voxel mean Euclidean distance of 0.05 millimeter in human cadaver temporal bones and 0.16 millimeter when applied to the described in vivo human synthetic data set in over 95% of all fusions. Performance times are less than two minutes.ConclusionHere a new and validated method based on existing techniques is described which could be used to accurately quantify migration of cochlear implant electrodes.

Analysis and evalaution in the production process and equipment area of the low-cost solar array project. [including modifying gaseous diffusion and using ion implantation

Science.gov (United States)

Goldman, H.; Wolf, M.

1979-01-01

The manufacturing methods for photovoltaic solar energy utilization are assessed. Economic and technical data on the current front junction formation processes of gaseous diffusion and ion implantation are presented. Future proposals, including modifying gaseous diffusion and using ion implantation, to decrease the cost of junction formation are studied. Technology developments in current processes and an economic evaluation of the processes are included.

Proposal and realization advertising campaign

OpenAIRE

RYCHLÁ, Marie

2008-01-01

The Bachelor Paper contains proposal and realization advertising campaign, including make charge for cost amount. The advertising campaign is made for chosen product of firm. Advertising campaign is planning by the medium of broadsheet and advertising on the Internet.

Scientific Opinion on a composting method proposed by Portugal as a heat treatment to eliminate pine wood nematode from the bark of pine trees

DEFF Research Database (Denmark)

Baker, R.; Candresse, T.; Dormannsné Simon, E.

2010-01-01

Following a request from the European Commission, the Panel on Plant Health was asked to deliver a scientific opinion on the appropriateness of a composting method proposed by Portugal as a heat treatment to eliminate pine wood nematode (PWN), Bursaphelenchus xylophilus (Steiner and Buhrer) Nickle......) insufficient evidence on the sampling methodology is provided to determine the reliability of the testing method provided by the Portuguese document to determine freedom from PWN. Although there is potential for development of a composting method as a heat treatment to eliminate PWN from bark of pine trees...

A New Hybrid Method for Improving the Performance of Myocardial Infarction Prediction

Directory of Open Access Journals (Sweden)

Hojatollah Hamidi

2016-06-01

Full Text Available Abstract Introduction: Myocardial Infarction, also known as heart attack, normally occurs due to such causes as smoking, family history, diabetes, and so on. It is recognized as one of the leading causes of death in the world. Therefore, the present study aimed to evaluate the performance of classification models in order to predict Myocardial Infarction, using a feature selection method that includes Forward Selection and Genetic Algorithm. Materials & Methods: The Myocardial Infarction data set used in this study contains the information related to 519 visitors to Shahid Madani Specialized Hospital of Khorramabad, Iran. This data set includes 33 features. The proposed method includes a hybrid feature selection method in order to enhance the performance of classification algorithms. The first step of this method selects the features using Forward Selection. At the second step, the selected features were given to a genetic algorithm, in order to select the best features. Classification algorithms entail Ada Boost, Naïve Bayes, J48 decision tree and simpleCART are applied to the data set with selected features, for predicting Myocardial Infarction. Results: The best results have been achieved after applying the proposed feature selection method, which were obtained via simpleCART and J48 algorithms with the accuracies of 96.53% and 96.34%, respectively. Conclusion: Based on the results, the performances of classification algorithms are improved. So, applying the proposed feature selection method, along with classification algorithms seem to be considered as a confident method with respect to predicting the Myocardial Infarction.

A method to reproduce alpha-particle spectra measured with semiconductor detectors.

Science.gov (United States)

Timón, A Fernández; Vargas, M Jurado; Sánchez, A Martín

2010-01-01

A method is proposed to reproduce alpha-particle spectra measured with silicon detectors, combining analytical and computer simulation techniques. The procedure includes the use of the Monte Carlo method to simulate the tracks of alpha-particles within the source and in the detector entrance window. The alpha-particle spectrum is finally obtained by the convolution of this simulated distribution and the theoretical distributions representing the contributions of the alpha-particle spectrometer to the spectrum. Experimental spectra from (233)U and (241)Am sources were compared with the predictions given by the proposed procedure, showing good agreement. The proposed method can be an important aid for the analysis and deconvolution of complex alpha-particle spectra. Copyright 2009 Elsevier Ltd. All rights reserved.

A proposal for experimental homework

Science.gov (United States)

Rodríguez, Eduardo E.

1998-10-01

Homework in Physics courses usually deal with conceptual inquiries or numerical solution of theoretical problems. However, experimental homework is rather uncommon. I propose that certain physical situations properly simulated may be useful to encourage students to seek a solution behind the steps of the "experimental method."

A New Pixels Flipping Method for Huge Watermarking Capacity of the Invoice Font Image

Directory of Open Access Journals (Sweden)

Li Li

2014-01-01

Full Text Available Invoice printing just has two-color printing, so invoice font image can be seen as binary image. To embed watermarks into invoice image, the pixels need to be flipped. The more huge the watermark is, the more the pixels need to be flipped. We proposed a new pixels flipping method in invoice image for huge watermarking capacity. The pixels flipping method includes one novel interpolation method for binary image, one flippable pixels evaluation mechanism, and one denoising method based on gravity center and chaos degree. The proposed interpolation method ensures that the invoice image keeps features well after scaling. The flippable pixels evaluation mechanism ensures that the pixels keep better connectivity and smoothness and the pattern has highest structural similarity after flipping. The proposed denoising method makes invoice font image smoother and fiter for human vision. Experiments show that the proposed flipping method not only keeps the invoice font structure well but also improves watermarking capacity.

A new pixels flipping method for huge watermarking capacity of the invoice font image.

Science.gov (United States)

Li, Li; Hou, Qingzheng; Lu, Jianfeng; Xu, Qishuai; Dai, Junping; Mao, Xiaoyang; Chang, Chin-Chen

2014-01-01

Invoice printing just has two-color printing, so invoice font image can be seen as binary image. To embed watermarks into invoice image, the pixels need to be flipped. The more huge the watermark is, the more the pixels need to be flipped. We proposed a new pixels flipping method in invoice image for huge watermarking capacity. The pixels flipping method includes one novel interpolation method for binary image, one flippable pixels evaluation mechanism, and one denoising method based on gravity center and chaos degree. The proposed interpolation method ensures that the invoice image keeps features well after scaling. The flippable pixels evaluation mechanism ensures that the pixels keep better connectivity and smoothness and the pattern has highest structural similarity after flipping. The proposed denoising method makes invoice font image smoother and fiter for human vision. Experiments show that the proposed flipping method not only keeps the invoice font structure well but also improves watermarking capacity.

Multi-Objective Dynamic Economic Dispatch of Microgrid Systems Including Vehicle-to-Grid

Directory of Open Access Journals (Sweden)

Haitao Liu

2015-05-01

Full Text Available Based on the characteristics of electric vehicles (EVs, this paper establishes the load models of EVs under the autonomous charging mode and the coordinated charging and discharging mode. Integrating the EVs into a microgrid system which includes wind turbines (WTs, photovoltaic arrays (PVs, diesel engines (DEs, fuel cells (FCs and a storage battery (BS, this paper establishes multi-objective economic dispatch models of a microgrid, including the lowest operating cost, the least carbon dioxide emissions, and the lowest pollutant treatment cost. After converting the multi-objective functions to a single objective function by using the judgment matrix method, we analyze the dynamic economic dispatch of the microgrid system including vehicle-to-grid (V2G with an improved particle swarm optimization algorithm under different operation control strategies. With the example system, the proposed models and strategies are verified and analyzed. Simulation results show that the microgrid system with EVs under the coordinated charging and discharging mode has better operation economics than the autonomous charging mode. Meanwhile, the greater the load fluctuation is, the higher the operating cost of the microgrid system is.

Monte Carlo based statistical power analysis for mediation models: methods and software.

Science.gov (United States)

Zhang, Zhiyong

2014-12-01

The existing literature on statistical power analysis for mediation models often assumes data normality and is based on a less powerful Sobel test instead of the more powerful bootstrap test. This study proposes to estimate statistical power to detect mediation effects on the basis of the bootstrap method through Monte Carlo simulation. Nonnormal data with excessive skewness and kurtosis are allowed in the proposed method. A free R package called bmem is developed to conduct the power analysis discussed in this study. Four examples, including a simple mediation model, a multiple-mediator model with a latent mediator, a multiple-group mediation model, and a longitudinal mediation model, are provided to illustrate the proposed method.

Proposal of a New Method for Neutron Dosimetry Based on Spectral Information Obtained by Application of Artificial Neural Networks

International Nuclear Information System (INIS)

Fehrenbacher, G.; Schuetz, R.; Hahn, K.; Sprunck, M.; Cordes, E.; Biersack, J.P.; Wahl, W.

1999-01-01

A new method for the monitoring of neutron radiation is proposed. It is based on the determination of spectral information on the neutron field in order to derive dose quantities like the ambient dose equivalent, the dose equivalent, or other dose quantities which depend on the neutron energy. The method uses a multi-element system consisting of converter type silicon detectors. The unfolding procedure is based on an artificial neural network (ANN). The response function of each element is determined by a computational model considering the neutron interaction with the dosemeter layers and the subsequent transport of produced ions. An example is given for a multi-element system. The ANN is trained by a given set of neutron spectra and then applied to count responses obtained in neutron fields. Four examples of spectra unfolded using the ANN are presented. (author)

Models including electron correlation in relation to Fock's proposed expansion of the ground-state wave function of He-like atomic ions

Energy Technology Data Exchange (ETDEWEB)

Glasser, M. L.; March, N. H.; Nieto, L. M. [Departamento de Fisica Teorica, Atomica y Optica, Universidad de Valladolid, ES-47011 Valladolid, Spain and Department of Physics, Clarkson University, Potsdam, New York 13699 (United States); Department of Physics, University of Antwerp, BE-2020 Antwerp, Belgium and Department of Theoretical Chemistry, University of Oxford, Oxford OX1 2JD (United Kingdom); Departamento de Fisica Teorica, Atomica y Optica, Universidad de Valladolid, ES-47011 Valladolid (Spain)

2011-12-15

Here attention is first drawn to the importance of gaining insight into Fock's early proposal for expanding the ground-state wave function for He-like atomic ions in hyperspherical coordinates. We approach the problem via two solvable models, namely, (i) the s-term model put forth by Temkin [Phys. Rev. 126, 130 (1962)] and (ii) the Hookean atom model proposed by Kestner and Sinanoglu [Phys. Rev. 128, 2687 (1962)]. In both cases the local kinetic energy can be obtained explicitly in hyperspherical coordinates. Separation of variables occurs in both model wave functions, though in a different context in the two cases. Finally, a k-space formulation is proposed that should eventually result in distinctive identifying characteristics of Fock's nonanalyticities for He-like atomic ions when both electrons are close to the nucleus.

50 CFR 85.22 - Grant proposals.

Science.gov (United States)

2010-10-01

... or benefits from accomplishing the objectives, including the numbers of recreational vessels and... should indicate how the activities contained in the proposal implements the plan); (b) Discrete objective...

Mapping subsurface pathways for contaminant migration at a proposed low level waste disposal site using electromagnetic methods

International Nuclear Information System (INIS)

Pin, F.G.; Ketelle, R.H.

1984-01-01

Electromagnetic methods have been used to measure apparent terrain conductivity in the downstream portion of a watershed in which a waste disposal site is proposed. At that site, the pathways for waste migration in ground water are controlled by subsurface channels. The channels are identified using isocurves of measured apparent conductivity. Two upstream channel branches are found to merge into a single downstream channel which constitutes the main drainage path out of the watershed. The identification and mapping of the ground water pathways is an important contribution to the site characterization study and the pathways analysis. The direct applications of terrain conductivity mapping to the planning of the monitoring program, the hydrogeological testing, and the modeling study are demonstrated. 7 references, 4 figures

Difference in target definition using three different methods to include respiratory motion in radiotherapy of lung cancer.

Science.gov (United States)

Sloth Møller, Ditte; Knap, Marianne Marquard; Nyeng, Tine Bisballe; Khalil, Azza Ahmed; Holt, Marianne Ingerslev; Kandi, Maria; Hoffmann, Lone

2017-11-01

Minimizing the planning target volume (PTV) while ensuring sufficient target coverage during the entire respiratory cycle is essential for free-breathing radiotherapy of lung cancer. Different methods are used to incorporate the respiratory motion into the PTV. Fifteen patients were analyzed. Respiration can be included in the target delineation process creating a respiratory GTV, denoted iGTV. Alternatively, the respiratory amplitude (A) can be measured based on the 4D-CT and A can be incorporated in the margin expansion. The GTV expanded by A yielded GTV + resp, which was compared to iGTV in terms of overlap. Three methods for PTV generation were compared. PTV del (delineated iGTV expanded to CTV plus PTV margin), PTV σ (GTV expanded to CTV and A was included as a random uncertainty in the CTV to PTV margin) and PTV ∑ (GTV expanded to CTV, succeeded by CTV linear expansion by A to CTV + resp, which was finally expanded to PTV ∑ ). Deformation of tumor and lymph nodes during respiration resulted in volume changes between the respiratory phases. The overlap between iGTV and GTV + resp showed that on average 7% of iGTV was outside the GTV + resp implying that GTV + resp did not capture the tumor during the full deformable respiration cycle. A comparison of the PTV volumes showed that PTV σ was smallest and PTV Σ largest for all patients. PTV σ was in mean 14% (31 cm 3 ) smaller than PTV del , while PTV del was 7% (20 cm 3 ) smaller than PTV Σ . PTV σ yields the smallest volumes but does not ensure coverage of tumor during the full respiratory motion due to tumor deformation. Incorporating the respiratory motion in the delineation (PTV del ) takes into account the entire respiratory cycle including deformation, but at the cost, however, of larger treatment volumes. PTV Σ should not be used, since it incorporates the disadvantages of both PTV del and PTV σ .

Reduction Method for Active Distribution Networks

DEFF Research Database (Denmark)

Raboni, Pietro; Chen, Zhe

2013-01-01

On-line security assessment is traditionally performed by Transmission System Operators at the transmission level, ignoring the effective response of distributed generators and small loads. On the other hand the required computation time and amount of real time data for including Distribution...... Networks also would be too large. In this paper an adaptive aggregation method for subsystems with power electronic interfaced generators and voltage dependant loads is proposed. With this tool may be relatively easier including distribution networks into security assessment. The method is validated...... by comparing the results obtained in PSCAD® with the detailed network model and with the reduced one. Moreover the control schemes of a wind turbine and a photovoltaic plant included in the detailed network model are described....

Economic Dispatch for Power System Included Wind and Solar Thermal Energy

Directory of Open Access Journals (Sweden)

Saoussen BRINI

2009-07-01

Full Text Available With the fast development of technologies of alternative energy, the electric power network can be composed of several renewable energy resources. The energy resources have various characteristics in terms of operational costs and reliability. In this study, the problem is the Economic Environmental Dispatching (EED of hybrid power system including wind and solar thermal energies. Renewable energy resources depend on the data of the climate such as the wind speed for wind energy, solar radiation and the temperature for solar thermal energy. In this article it proposes a methodology to solve this problem. The resolution takes account of the fuel costs and reducing of the emissions of the polluting gases. The resolution is done by the Strength Pareto Evolutionary Algorithm (SPEA method and the simulations have been made on an IEEE network test (30 nodes, 8 machines and 41 lines.

Geochemical data from groundwater at the proposed Dewey Burdock uranium in-situ recovery mine, Edgemont, South Dakota

Science.gov (United States)

Johnson, Raymond H.

2012-01-01

This report releases groundwater geochemistry data from samples that were collected in June 2011 at the Dewey Burdock proposed uranium in-situ recovery site near Edgemont, South Dakota. The sampling and analytical methods are summarized, and all of the data, including quality assurance/quality control information are provided in data tables.

Polycrystalline-Diamond MEMS Biosensors Including Neural Microelectrode-Arrays

Directory of Open Access Journals (Sweden)

Donna H. Wang

2011-08-01

Full Text Available Diamond is a material of interest due to its unique combination of properties, including its chemical inertness and biocompatibility. Polycrystalline diamond (poly-C has been used in experimental biosensors that utilize electrochemical methods and antigen-antibody binding for the detection of biological molecules. Boron-doped poly-C electrodes have been found to be very advantageous for electrochemical applications due to their large potential window, low background current and noise, and low detection limits (as low as 500 fM. The biocompatibility of poly-C is found to be comparable, or superior to, other materials commonly used for implants, such as titanium and 316 stainless steel. We have developed a diamond-based, neural microelectrode-array (MEA, due to the desirability of poly-C as a biosensor. These diamond probes have been used for in vivo electrical recording and in vitro electrochemical detection. Poly-C electrodes have been used for electrical recording of neural activity. In vitro studies indicate that the diamond probe can detect norepinephrine at a 5 nM level. We propose a combination of diamond micro-machining and surface functionalization for manufacturing diamond pathogen-microsensors.

Proposed Terminology and Classification of Pre-Malignant Neoplastic Conditions: A Consensus Proposal.

Science.gov (United States)

Valent, Peter; Akin, Cem; Arock, Michel; Bock, Christoph; George, Tracy I; Galli, Stephen J; Gotlib, Jason; Haferlach, Torsten; Hoermann, Gregor; Hermine, Olivier; Jäger, Ulrich; Kenner, Lukas; Kreipe, Hans; Majeti, Ravindra; Metcalfe, Dean D; Orfao, Alberto; Reiter, Andreas; Sperr, Wolfgang R; Staber, Philipp B; Sotlar, Karl; Schiffer, Charles; Superti-Furga, Giulio; Horny, Hans-Peter

2017-12-01

Cancer evolution is a step-wise non-linear process that may start early in life or later in adulthood, and includes pre-malignant (indolent) and malignant phases. Early somatic changes may not be detectable or are found by chance in apparently healthy individuals. The same lesions may be detected in pre-malignant clonal conditions. In some patients, these lesions may never become relevant clinically whereas in others, they act together with additional pro-oncogenic hits and thereby contribute to the formation of an overt malignancy. Although some pre-malignant stages of a malignancy have been characterized, no global system to define and to classify these conditions is available. To discuss open issues related to pre-malignant phases of neoplastic disorders, a working conference was organized in Vienna in August 2015. The outcomes of this conference are summarized herein and include a basic proposal for a nomenclature and classification of pre-malignant conditions. This proposal should assist in the communication among patients, physicians and scientists, which is critical as genome-sequencing will soon be offered widely for early cancer-detection. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Assessing CO2 Mitigation Options Utilizing Detailed Electricity Characteristics and Including Renewable Generation

Science.gov (United States)

Bensaida, K.; Alie, Colin; Elkamel, A.; Almansoori, A.

2017-08-01

This paper presents a novel techno-economic optimization model for assessing the effectiveness of CO2 mitigation options for the electricity generation sub-sector that includes renewable energy generation. The optimization problem was formulated as a MINLP model using the GAMS modeling system. The model seeks the minimization of the power generation costs under CO2 emission constraints by dispatching power from low CO2 emission-intensity units. The model considers the detailed operation of the electricity system to effectively assess the performance of GHG mitigation strategies and integrates load balancing, carbon capture and carbon taxes as methods for reducing CO2 emissions. Two case studies are discussed to analyze the benefits and challenges of the CO2 reduction methods in the electricity system. The proposed mitigations options would not only benefit the environment, but they will as well improve the marginal cost of producing energy which represents an advantage for stakeholders.

Improved Quasi-Newton method via PSB update for solving systems of nonlinear equations

Science.gov (United States)

Mamat, Mustafa; Dauda, M. K.; Waziri, M. Y.; Ahmad, Fadhilah; Mohamad, Fatma Susilawati

2016-10-01

The Newton method has some shortcomings which includes computation of the Jacobian matrix which may be difficult or even impossible to compute and solving the Newton system in every iteration. Also, the common setback with some quasi-Newton methods is that they need to compute and store an n × n matrix at each iteration, this is computationally costly for large scale problems. To overcome such drawbacks, an improved Method for solving systems of nonlinear equations via PSB (Powell-Symmetric-Broyden) update is proposed. In the proposed method, the approximate Jacobian inverse Hk of PSB is updated and its efficiency has improved thereby require low memory storage, hence the main aim of this paper. The preliminary numerical results show that the proposed method is practically efficient when applied on some benchmark problems.

Edge detection methods based on generalized type-2 fuzzy logic

CERN Document Server

Gonzalez, Claudia I; Castro, Juan R; Castillo, Oscar

2017-01-01

In this book four new methods are proposed. In the first method the generalized type-2 fuzzy logic is combined with the morphological gra-dient technique. The second method combines the general type-2 fuzzy systems (GT2 FSs) and the Sobel operator; in the third approach the me-thodology based on Sobel operator and GT2 FSs is improved to be applied on color images. In the fourth approach, we proposed a novel edge detec-tion method where, a digital image is converted a generalized type-2 fuzzy image. In this book it is also included a comparative study of type-1, inter-val type-2 and generalized type-2 fuzzy systems as tools to enhance edge detection in digital images when used in conjunction with the morphologi-cal gradient and the Sobel operator. The proposed generalized type-2 fuzzy edge detection methods were tested with benchmark images and synthetic images, in a grayscale and color format. Another contribution in this book is that the generalized type-2 fuzzy edge detector method is applied in the preproc...

Proposal of a micromagnetic standard problem for ferromagnetic resonance simulations

Energy Technology Data Exchange (ETDEWEB)

Baker, Alexander [Department of Physics, Clarendon Laboratory, University of Oxford, Oxford, 3PU, OX1 (United Kingdom); Beg, Marijan; Ashton, Gregory; Albert, Maximilian; Chernyshenko, Dmitri [Faculty of Engineering and the Environment, University of Southampton, SO17 1BJ, Southampton (United Kingdom); Wang, Weiwei [Department of Physics, Ningbo University, Ningbo, 315211 China (China); Zhang, Shilei [Department of Physics, Clarendon Laboratory, University of Oxford, Oxford, 3PU, OX1 (United Kingdom); Bisotti, Marc-Antonio; Franchin, Matteo [Faculty of Engineering and the Environment, University of Southampton, SO17 1BJ, Southampton (United Kingdom); Hu, Chun Lian; Stamps, Robert [SUPA School of Physics and Astronomy, University of Glasgow, G12, Glasgow, 8QQ United Kingdom (United Kingdom); Hesjedal, Thorsten, E-mail: t.hesjedal1@physics.ox.ac.uk [Department of Physics, Clarendon Laboratory, University of Oxford, Oxford, 3PU, OX1 (United Kingdom); Fangohr, Hans [Faculty of Engineering and the Environment, University of Southampton, SO17 1BJ, Southampton (United Kingdom)

2017-01-01

Nowadays, micromagnetic simulations are a common tool for studying a wide range of different magnetic phenomena, including the ferromagnetic resonance. A technique for evaluating reliability and validity of different micromagnetic simulation tools is the simulation of proposed standard problems. We propose a new standard problem by providing a detailed specification and analysis of a sufficiently simple problem. By analyzing the magnetization dynamics in a thin permalloy square sample, triggered by a well defined excitation, we obtain the ferromagnetic resonance spectrum and identify the resonance modes via Fourier transform. Simulations are performed using both finite difference and finite element numerical methods, with OOMMF and Nmag simulators, respectively. We report the effects of initial conditions and simulation parameters on the character of the observed resonance modes for this standard problem. We provide detailed instructions and code to assist in using the results for evaluation of new simulator tools, and to help with numerical calculation of ferromagnetic resonance spectra and modes in general. - Highlights: ●Micromagnetic standard problem for FerroMagnetic Resonance (FMR). ●Overview of FMR simulation techniques. ●Define reproducible test problem with ring down method. ●Example configuration files, scripts and post processing for OOMMF and NMag. ●Code and data available in Ref. [23].

Quality Assurance in Higher Education: Proposals for Consultation.

Science.gov (United States)

Higher Education Funding Council for England, Bristol.

This document sets out for consultation proposals for a revised method for quality assurance of teaching and learning in higher education. The proposals cover: (1) the objectives and principles of quality assurance; (2) an approach to quality assurance based on external audit principles; (3) the collection and publication of information; (4)…

An Aggregated Method for Determining Railway Defects and Obstacle Parameters

Science.gov (United States)

Loktev, Daniil; Loktev, Alexey; Stepanov, Roman; Pevzner, Viktor; Alenov, Kanat

2018-03-01

The method of combining algorithms of image blur analysis and stereo vision to determine the distance to objects (including external defects of railway tracks) and the speed of moving objects-obstacles is proposed. To estimate the deviation of the distance depending on the blur a statistical approach, logarithmic, exponential and linear standard functions are used. The statistical approach includes a method of estimating least squares and the method of least modules. The accuracy of determining the distance to the object, its speed and direction of movement is obtained. The paper develops a method of determining distances to objects by analyzing a series of images and assessment of depth using defocusing using its aggregation with stereoscopic vision. This method is based on a physical effect of dependence on the determined distance to the object on the obtained image from the focal length or aperture of the lens. In the calculation of the blur spot diameter it is assumed that blur occurs at the point equally in all directions. According to the proposed approach, it is possible to determine the distance to the studied object and its blur by analyzing a series of images obtained using the video detector with different settings. The article proposes and scientifically substantiates new and improved existing methods for detecting the parameters of static and moving objects of control, and also compares the results of the use of various methods and the results of experiments. It is shown that the aggregate method gives the best approximation to the real distances.

An Accurate and Impartial Expert Assignment Method for Scientific Project Review

Directory of Open Access Journals (Sweden)

Mingliang Yue

2017-12-01

Full Text Available Purpose: This paper proposes an expert assignment method for scientific project review that considers both accuracy and impartiality. As impartial and accurate peer review is extremely important to ensure the quality and feasibility of scientific projects, enhanced methods for managing the process are needed. Design/methodology/approach: To ensure both accuracy and impartiality, we design four criteria, the reviewers’ fitness degree, research intensity, academic association, and potential conflict of interest, to express the characteristics of an appropriate peer review expert. We first formalize the expert assignment problem as an optimization problem based on the designed criteria, and then propose a randomized algorithm to solve the expert assignment problem of identifying reviewer adequacy. Findings: Simulation results show that the proposed method is quite accurate and impartial during expert assignment. Research limitations: Although the criteria used in this paper can properly show the characteristics of a good and appropriate peer review expert, more criteria/conditions can be included in the proposed scheme to further enhance accuracy and impartiality of the expert assignment. Practical implications: The proposed method can help project funding agencies (e.g. the National Natural Science Foundation of China find better experts for project peer review. Originality/value: To the authors’ knowledge, this is the first publication that proposes an algorithm that applies an impartial approach to the project review expert assignment process. The simulation results show the effectiveness of the proposed method.

Explicit time marching methods for the time-dependent Euler computations

International Nuclear Information System (INIS)

Tai, C.H.; Chiang, D.C.; Su, Y.P.

1997-01-01

Four explicit type time marching methods, including one proposed by the authors, are examined. The TVD conditions of this method are analyzed with the linear conservation law as the model equation. Performance of these methods when applied to the Euler equations are numerically tested. Seven examples are tested, the main concern is the performance of the methods when discontinuities with different strengths are encountered. When the discontinuity is getting stronger, spurious oscillation shows up for three existing methods, while the method proposed by the authors always gives the results with satisfaction. The effect of the limiter is also investigated. To put these methods in the same basis for the comparison the same spatial discretization is used. Roe's solver is used to evaluate the fluxes at the cell interface; spatially second-order accuracy is achieved by the MUSCL reconstruction. 19 refs., 8 figs

Proposed test method for determining discharge rates from water closets

DEFF Research Database (Denmark)

Nielsen, V.; Fjord Jensen, T.

At present the rates at which discharge takes place from sanitary appliances are mostly known only in the form of estimated average values. SBI has developed a measuring method enabling determination of the exact rate of discharge from a sanitary appliance as function of time. The methods depends...

Effects of disease severity distribution on the performance of quantitative diagnostic methods and proposal of a novel ‘V-plot’ methodology to display accuracy values

Science.gov (United States)

Dehbi, Hakim-Moulay; Howard, James P; Shun-Shin, Matthew J; Sen, Sayan; Nijjer, Sukhjinder S; Mayet, Jamil; Davies, Justin E; Francis, Darrel P

2018-01-01

Background Diagnostic accuracy is widely accepted by researchers and clinicians as an optimal expression of a test’s performance. The aim of this study was to evaluate the effects of disease severity distribution on values of diagnostic accuracy as well as propose a sample-independent methodology to calculate and display accuracy of diagnostic tests. Methods and findings We evaluated the diagnostic relationship between two hypothetical methods to measure serum cholesterol (Cholrapid and Cholgold) by generating samples with statistical software and (1) keeping the numerical relationship between methods unchanged and (2) changing the distribution of cholesterol values. Metrics of categorical agreement were calculated (accuracy, sensitivity and specificity). Finally, a novel methodology to display and calculate accuracy values was presented (the V-plot of accuracies). Conclusion No single value of diagnostic accuracy can be used to describe the relationship between tests, as accuracy is a metric heavily affected by the underlying sample distribution. Our novel proposed methodology, the V-plot of accuracies, can be used as a sample-independent measure of a test performance against a reference gold standard. PMID:29387424

Tubelets : Unsupervised Action Proposals from Spatiotemporal Super-Voxels

NARCIS (Netherlands)

Jain, Mihir; van Gemert, J.C.; Jégou, Hervé; Bouthemy, Patrick; Snoek, Cees G.M.

2017-01-01

This paper considers the problem of localizing actions in videos as sequences of bounding boxes. The objective is to generate action proposals that are likely to include the action of interest, ideally achieving high recall with few proposals. Our contributions are threefold. First, inspired by

13 CFR 305.6 - Allowable methods of procurement for construction services.

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Allowable methods of procurement for construction services. 305.6 Section 305.6 Business Credit and Assistance ECONOMIC DEVELOPMENT... advertisement for bids and shall include the following, as applicable: (1) Justification for the proposed method...

A proposal of an open PET geometry

Energy Technology Data Exchange (ETDEWEB)

Yamaya, Taiga [Molecular Imaging Center, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba, 263-8555 (Japan); Inaniwa, Taku [Research Center for Charged Particle Therapy, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba 263-8555 (Japan); Minohara, Shinichi [Research Center for Charged Particle Therapy, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba 263-8555 (Japan); Yoshida, Eiji [Molecular Imaging Center, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba, 263-8555 (Japan); Inadama, Naoko [Molecular Imaging Center, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba, 263-8555 (Japan); Nishikido, Fumihiko [Molecular Imaging Center, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba, 263-8555 (Japan); Shibuya, Kengo [Molecular Imaging Center, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba, 263-8555 (Japan); Lam, Chih Fung [Molecular Imaging Center, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba, 263-8555 (Japan); Murayama, Hideo [Molecular Imaging Center, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba, 263-8555 (Japan)

2008-02-07

The long patient port of a PET scanner tends to put stress on patients, especially patients with claustrophobia. It also prevents doctors and technicians from taking care of patients during scanning. In this paper, we proposed an 'open PET' geometry, which consists of two axially separated detector rings. A long and continuous field-of-view (FOV) including a 360 deg. opened gap between two detector rings can be imaged enabling a fully 3D image reconstruction of all the possible lines-of-response. The open PET will become practical if iterative image reconstruction methods are applied even though image reconstruction of the open PET is analytically an incomplete problem. First we implemented a 'masked' 3D ordered subset expectation maximization (OS-EM) in which the system matrix was obtained from a long 'gapless' scanner by applying a mask to detectors corresponding to the open space. Next, in order to evaluate imaging performance of the proposed open PET geometry, we simulated a dual HR+ scanner (ring diameter of D = 827 mm, axial length of W = 154 mm x 2) separated by a variable gap. The gap W was the maximum limit to have axially continuous FOV of 3W though the maximum diameter of FOV at the central slice was limited to D/2. Artifacts, observed on both sides of the open space when the gap exceeded W, were effectively reduced by inserting detectors partially into unnecessary open spaces. We also tested the open PET geometry using experimental data obtained by the jPET-D4. The jPET-D4 is a prototype brain scanner, which has 5 rings of 24 detector blocks. We simulated the open jPET-D4 with a gap of 66 mm by eliminating 1 block-ring from experimental data. Although some artifacts were seen at both ends of the opened gap, very similar images were obtained with and without the gap. The proposed open PET geometry is expected to lead to realization of in-beam PET, which is a method for an in situ monitoring of charged particle therapy, by

Proposal on the mitigation methods of thermal stress near the sodium

International Nuclear Information System (INIS)

Ando, Masanori; Kasahara, Naoto

2003-09-01

A Reactor vessel of fast rector plants contains high temperature liquid sodium in its inside and its upper end is supported by a low temperature structures. Therefore, a significant temperature gradient will arise at the vessel wall near the sodium surface. For this reason, a large thermal stress will be generated around this part. To lower this stress and to protect the vessel, a number of methods have been applied the plants. Generally, these mitigation methods by protection equipments for thermal stress also have some problems such as, increase a mount of materials or to be complicate for control, hard to maintenance and so on. In this research, authors suggested another simple methods for thermal stress, and evaluated their effects using computer analysis. The results obtained in this research are as follows. Authors suggested one method, circulate high temperature gas around outside of the vessel and evaluated the effects of this method by analysis. In case of using this method, Sn (one of index values of design) value might be getting lower about 45%. Authors also suggested another method by setting up a heat transfer plate outside of the vessel and evaluated the effects of this method by analysis. Effects of this method depend on material of the plate. In case of using Carbon as material of plate, Sn value might be 27% lower and in case of using 12Cr steel as material of plate, Sn value might be 15% lower. Authors also suggested another method by changing material of the guard vessel to be the one which has good ability of heat transfer and evaluated the effects of this method by analysis. In case of changing material of guard vessel to 12Cr steel, Sn value might be lower about 12%. (author)

An alternative method for centrifugal compressor loading factor modelling

Science.gov (United States)

Galerkin, Y.; Drozdov, A.; Rekstin, A.; Soldatova, K.

2017-08-01

The loading factor at design point is calculated by one or other empirical formula in classical design methods. Performance modelling as a whole is out of consideration. Test data of compressor stages demonstrates that loading factor versus flow coefficient at the impeller exit has a linear character independent of compressibility. Known Universal Modelling Method exploits this fact. Two points define the function - loading factor at design point and at zero flow rate. The proper formulae include empirical coefficients. A good modelling result is possible if the choice of coefficients is based on experience and close analogs. Earlier Y. Galerkin and K. Soldatova had proposed to define loading factor performance by the angle of its inclination to the ordinate axis and by the loading factor at zero flow rate. Simple and definite equations with four geometry parameters were proposed for loading factor performance calculated for inviscid flow. The authors of this publication have studied the test performance of thirteen stages of different types. The equations are proposed with universal empirical coefficients. The calculation error lies in the range of plus to minus 1,5%. The alternative model of a loading factor performance modelling is included in new versions of the Universal Modelling Method.

Describing qualitative research undertaken with randomised controlled trials in grant proposals: a documentary analysis

Science.gov (United States)

2014-01-01

Background There is growing recognition of the value of conducting qualitative research with trials in health research. It is timely to reflect on how this qualitative research is presented in grant proposals to identify lessons for researchers and research commissioners. As part of a larger study focusing on how to maximise the value of undertaking qualitative research with trials, we undertook a documentary analysis of proposals of funded studies. Methods Using the metaRegister of Controlled Trials (mRCT) database we identified trials funded in the United Kingdom, ongoing between 2001 and 2010, and reporting the use of qualitative research. We requested copies of proposals from lead researchers. We extracted data from the proposals using closed and open questions, analysed using descriptive statistics and content analysis respectively. Results 2% (89/3812) of trials in the mRCT database described the use of qualitative research undertaken with the trial. From these 89 trials, we received copies of 36 full proposals, of which 32 met our inclusion criteria. 25% used less than a single paragraph to describe the qualitative research. The aims of the qualitative research described in these proposals focused mainly on the intervention or trial conduct. Just over half (56%) of the proposals included an explicit rationale for conducting the qualitative research with the trial, the most frequent being to optimise implementation into clinical practice or to interpret trial findings. Key information about methods, expertise and resources was missing in a large minority of proposals, in particular sample size, type of analysis, and non-personnel resources. 28% specifically stated that qualitative researchers would conduct the qualitative research. Conclusions Our review of proposals of successfully funded studies identified good practice but also identified limited space given to describing the qualitative research, with an associated lack of attention to the rationale for

A methodological survey identified eight proposed frameworks for the adaptation of health related guidelines.

Science.gov (United States)

Darzi, Andrea; Abou-Jaoude, Elias A; Agarwal, Arnav; Lakis, Chantal; Wiercioch, Wojtek; Santesso, Nancy; Brax, Hneine; El-Jardali, Fadi; Schünemann, Holger J; Akl, Elie A

2017-06-01

Our objective was to identify and describe published frameworks for adaptation of clinical, public health, and health services guidelines. We included reports describing methods of adaptation of guidelines in sufficient detail to allow its reproducibility. We searched Medline and EMBASE databases. We also searched personal files, as well manuals and handbooks of organizations and professional societies that proposed methods of adaptation and adoption of guidelines. We followed standard systematic review methodology. Our search captured 12,021 citations, out of which we identified eight proposed methods of guidelines adaptation: ADAPTE, Adapted ADAPTE, Alberta Ambassador Program adaptation phase, GRADE-ADOLOPMENT, MAGIC, RAPADAPTE, Royal College of Nursing (RCN), and Systematic Guideline Review (SGR). The ADAPTE framework consists of a 24-step process to adapt guidelines to a local context taking into consideration the needs, priorities, legislation, policies, and resources. The Alexandria Center for Evidence-Based Clinical Practice Guidelines updated one of ADAPTE's tools, modified three tools, and added three new ones. In addition, they proposed optionally using three other tools. The Alberta Ambassador Program adaptation phase consists of 11 steps and focused on adapting good-quality guidelines for nonspecific low back pain into local context. GRADE-ADOLOPMENT is an eight-step process based on the GRADE Working Group's Evidence to Decision frameworks and applied in 22 guidelines in the context of national guideline development program. The MAGIC research program developed a five-step adaptation process, informed by ADAPTE and the GRADE approach in the context of adapting thrombosis guidelines. The RAPADAPTE framework consists of 12 steps based on ADAPTE and using synthesized evidence databases, retrospectively derived from the experience of producing a high-quality guideline for the treatment of breast cancer with limited resources in Costa Rica. The RCN outlines

The development of methods of analysis of documents on the basis of the methods of Raman spectroscopy and fluorescence analysis

Science.gov (United States)

Gorshkova, Kseniia O.; Tumkin, Ilya I.; Kirillova, Elizaveta O.; Panov, Maxim S.; Kochemirovsky, Vladimir A.

2017-05-01

The investigation of natural aging of writing inks printed on paper using Raman spectroscopy was performed. Based on the obtained dependencies of the Raman peak intensities ratios on the exposure time, the dye degradation model was proposed. It was suggested that there are several competing bond breaking and bond forming reactions corresponding to the characteristic vibration frequencies of the dye molecule that simultaneously occur during ink aging process. Also we propose a methodology based on the study of the optical properties of paper, particularly changes in the fluorescence of optical brighteners included in its composition as well as the paper reflectivity using spectrophotometric methods. These results can be implemented to develop the novel and promising method of criminology.

Heterogeneous Data Fusion Method to Estimate Travel Time Distributions in Congested Road Networks

OpenAIRE

Chaoyang Shi; Bi Yu Chen; William H. K. Lam; Qingquan Li

2017-01-01

Travel times in congested urban road networks are highly stochastic. Provision of travel time distribution information, including both mean and variance, can be very useful for travelers to make reliable path choice decisions to ensure higher probability of on-time arrival. To this end, a heterogeneous data fusion method is proposed to estimate travel time distributions by fusing heterogeneous data from point and interval detectors. In the proposed method, link travel time distributions are f...

Evaluation and comparison of multiple test methods, including real-time PCR, for Legionella detection in clinical specimens.

Directory of Open Access Journals (Sweden)

Adriana Peci

2016-08-01

Full Text Available Legionella is a gram-negative bacterium that can cause Pontiac fever, a mild upper respiratory infection and Legionnaire’s disease, a more severe illness. We aimed to compare the performance of urine antigen, culture and PCR test methods and to determine if sputum is an alternative to the use of more invasive bronchoalveolar lavage (BAL. Data for this study included specimens tested for Legionella at PHOL from January 1, 2010 to April 30, 2014, as part of routine clinical testing. We found sensitivity of UAT compared to culture to be 87%, specificity 94.7%, positive predictive value (PPV 63.8% and negative predictive value (NPV 98.5%. Sensitivity of UAT compared to PCR was 74.7%, specificity 98.3%, PPV 77.7% and NPV 98.1%. Of 146 patients who had a Legionella positive result by PCR, only 66(45.2% also had a positive result by culture. Sensitivity for culture was the same using either sputum or BAL (13.6%; sensitivity for PCR was 10.3% for sputum and 12.8% for BAL. Both sputum and BAL yield similar results despite testing methods (Fisher Exact p-values=1.0, for each test. In summary, all test methods have inherent weaknesses in identifying Legionella; thereforemore than one testing method should be used. Obtaining a single specimen type from patients with pneumonia limits the ability to diagnose Legionella, particularly when urine is the specimen type submitted. Given ease of collection, and similar sensitivity to BAL, clinicians are encouraged to submit sputum in addition to urine when BAL submission is not practical, from patients being tested for Legionella.

A Resampling-Based Stochastic Approximation Method for Analysis of Large Geostatistical Data

KAUST Repository

Liang, Faming

2013-03-01

The Gaussian geostatistical model has been widely used in modeling of spatial data. However, it is challenging to computationally implement this method because it requires the inversion of a large covariance matrix, particularly when there is a large number of observations. This article proposes a resampling-based stochastic approximation method to address this challenge. At each iteration of the proposed method, a small subsample is drawn from the full dataset, and then the current estimate of the parameters is updated accordingly under the framework of stochastic approximation. Since the proposed method makes use of only a small proportion of the data at each iteration, it avoids inverting large covariance matrices and thus is scalable to large datasets. The proposed method also leads to a general parameter estimation approach, maximum mean log-likelihood estimation, which includes the popular maximum (log)-likelihood estimation (MLE) approach as a special case and is expected to play an important role in analyzing large datasets. Under mild conditions, it is shown that the estimator resulting from the proposed method converges in probability to a set of parameter values of equivalent Gaussian probability measures, and that the estimator is asymptotically normally distributed. To the best of the authors\\' knowledge, the present study is the first one on asymptotic normality under infill asymptotics for general covariance functions. The proposed method is illustrated with large datasets, both simulated and real. Supplementary materials for this article are available online. © 2013 American Statistical Association.

Biomimetic design method for innovation and sustainability

CERN Document Server

Helfman Cohen, Yael

2017-01-01

Presenting a novel biomimetic design method for transferring design solutions from nature to technology, this book focuses on structure-function patterns in nature and advanced modeling tools derived from TRIZ, the theory of inventive problem-solving. The book includes an extensive literature review on biomimicry as an engine of both innovation and sustainability, and discusses in detail the biomimetic design process, current biomimetic design methods and tools. The structural biomimetic design method for innovation and sustainability put forward in this text encompasses (1) the research method and rationale used to develop and validate this new design method; (2) the suggested design algorithm and tools including the Findstructure database, structure-function patterns and ideality patterns; and (3) analyses of four case studies describing how to use the proposed method. This book offers an essential resource for designers who wish to use nature as a source of inspiration and knowledge, innovators and sustain...

Improvement of vector compensation method for vehicle magnetic distortion field

Energy Technology Data Exchange (ETDEWEB)

Pang, Hongfeng, E-mail: panghongfeng@126.com; Zhang, Qi; Li, Ji; Luo, Shitu; Chen, Dixiang; Pan, Mengchun; Luo, Feilu

2014-03-15

Magnetic distortions such as eddy-current field and low frequency magnetic field have not been considered in vector compensation methods. A new compensation method is proposed to suppress these magnetic distortions and improve compensation performance, in which the magnetic distortions related to measurement vectors and time are considered. The experimental system mainly consists of a three-axis fluxgate magnetometer (DM-050), an underwater vehicle and a proton magnetometer, in which the scalar value of magnetic field is obtained with the proton magnetometer and considered to be the true value. Comparing with traditional compensation methods, experimental results show that the magnetic distortions can be further reduced by two times. After compensation, error intensity and RMS error are reduced from 11684.013 nT and 7794.604 nT to 16.219 nT and 5.907 nT respectively. It suggests an effective way to improve the compensation performance of magnetic distortions. - Highlights: • A new vector compensation method is proposed for vehicle magnetic distortion. • The proposed model not only includes magnetometer error but also considers magnetic distortion. • Compensation parameters are computed directly by solving nonlinear equations. • Compared with traditional methods, the proposed method is not related with rotation angle rate. • Error intensity and RMS error can be reduced to 1/2 of the error with traditional methods.

Improvement of vector compensation method for vehicle magnetic distortion field

International Nuclear Information System (INIS)

Pang, Hongfeng; Zhang, Qi; Li, Ji; Luo, Shitu; Chen, Dixiang; Pan, Mengchun; Luo, Feilu

2014-01-01

Magnetic distortions such as eddy-current field and low frequency magnetic field have not been considered in vector compensation methods. A new compensation method is proposed to suppress these magnetic distortions and improve compensation performance, in which the magnetic distortions related to measurement vectors and time are considered. The experimental system mainly consists of a three-axis fluxgate magnetometer (DM-050), an underwater vehicle and a proton magnetometer, in which the scalar value of magnetic field is obtained with the proton magnetometer and considered to be the true value. Comparing with traditional compensation methods, experimental results show that the magnetic distortions can be further reduced by two times. After compensation, error intensity and RMS error are reduced from 11684.013 nT and 7794.604 nT to 16.219 nT and 5.907 nT respectively. It suggests an effective way to improve the compensation performance of magnetic distortions. - Highlights: • A new vector compensation method is proposed for vehicle magnetic distortion. • The proposed model not only includes magnetometer error but also considers magnetic distortion. • Compensation parameters are computed directly by solving nonlinear equations. • Compared with traditional methods, the proposed method is not related with rotation angle rate. • Error intensity and RMS error can be reduced to 1/2 of the error with traditional methods

Enhancing the (MSLDIP) image steganographic method (ESLDIP method)

Science.gov (United States)

Seddik Saad, Al-hussien

2011-10-01

Message transmissions over the Internet still have data security problem. Therefore, secure and secret communication methods are needed for transmitting messages over the Internet. Cryptography scrambles the message so that it cannot be understood. However, it makes the message suspicious enough to attract eavesdropper's attention. Steganography hides the secret message within other innocuous-looking cover files (i.e. images, music and video files) so that it cannot be observed [1].The term steganography originates from the Greek root words "steganos'' and "graphein'' which literally mean "covered writing''. It is defined as the science that involves communicating secret data in an appropriate multimedia carrier, e.g., image, audio text and video files [3].Steganographic techniques allow one party to communicate information to another without a third party even knowing that the communication is occurring. The ways to deliver these "secret messages" vary greatly [3].Our proposed method called Enhanced SLDIP (ESLDIP). In which the maximmum hiding capacity (MHC) of proposed ESLDIP method is higher than the previously proposed MSLDIP methods and the PSNR of the ESLDIP method is higher than the MSLDIP PSNR values', which means that the image quality of the ESLDIP method will be better than MSLDIP method and the maximmum hiding capacity (MHC) also improved. The rest of this paper is organized as follows. In section 2, steganography has been discussed; lingo, carriers and types. In section 3, related works are introduced. In section 4, the proposed method will be discussed in details. In section 5, the simulation results are given and Section 6 concludes the paper.

TRANSAT-- method for detecting the conserved helices of functional RNA structures, including transient, pseudo-knotted and alternative structures.

Science.gov (United States)

Wiebe, Nicholas J P; Meyer, Irmtraud M

2010-06-24

The prediction of functional RNA structures has attracted increased interest, as it allows us to study the potential functional roles of many genes. RNA structure prediction methods, however, assume that there is a unique functional RNA structure and also do not predict functional features required for in vivo folding. In order to understand how functional RNA structures form in vivo, we require sophisticated experiments or reliable prediction methods. So far, there exist only a few, experimentally validated transient RNA structures. On the computational side, there exist several computer programs which aim to predict the co-transcriptional folding pathway in vivo, but these make a range of simplifying assumptions and do not capture all features known to influence RNA folding in vivo. We want to investigate if evolutionarily related RNA genes fold in a similar way in vivo. To this end, we have developed a new computational method, Transat, which detects conserved helices of high statistical significance. We introduce the method, present a comprehensive performance evaluation and show that Transat is able to predict the structural features of known reference structures including pseudo-knotted ones as well as those of known alternative structural configurations. Transat can also identify unstructured sub-sequences bound by other molecules and provides evidence for new helices which may define folding pathways, supporting the notion that homologous RNA sequence not only assume a similar reference RNA structure, but also fold similarly. Finally, we show that the structural features predicted by Transat differ from those assuming thermodynamic equilibrium. Unlike the existing methods for predicting folding pathways, our method works in a comparative way. This has the disadvantage of not being able to predict features as function of time, but has the considerable advantage of highlighting conserved features and of not requiring a detailed knowledge of the cellular

International survey of methods used in health technology assessment (HTA: does practice meet the principles proposed for good research?

Directory of Open Access Journals (Sweden)

Stephens JM

2012-08-01

Full Text Available Jennifer M Stephens,1 Bonnie Handke,2 Jalpa A Doshi3 On behalf of the HTA Principles Working Group, part of the International Society for Pharmacoeconomics and Outcomes Research (ISPOR HTA Special Interest Group (SIG1Pharmerit International, Bethesda, MD, USA; 2Medtronic Neuromodulation, Minneapolis, MN, USA; 3Center for Evidence-Based Practice and Center for Health Incentives and Behavioral Economics, Perelman School of Medicine, University of Pennsylvania, Philadelphia, PA, USAObjective: To describe research methods used internationally in health technology assessment (HTA and health-care reimbursement policies; compare the survey findings on research methods and processes to published HTA principles; and discuss important issues/trends reported by HTA bodies related to current research methods and applications of the HTA process.Methods: Representatives from HTA bodies worldwide were recruited to complete an online survey consisting of 47 items within four topics: (1 organizational information and process, (2 primary HTA methodologies and importance of attributes, (3 HTA application and dissemination, and (4 quality of HTA, including key issues. Results were presented as a comparison of current HTA practices and research methods to published HTA principles.Results: The survey was completed by 30 respondents representing 16 countries in five major regions, Australia (n = 3, Canada (n = 2, Europe (n = 17, Latin America (n = 2, and the United States (n = 6. The most common methodologies used were systematic review, meta-analysis, and economic modeling. The most common attributes evaluated were effectiveness (more commonly than efficacy, cost-effectiveness, safety, and quality of life. The attributes assessed, relative importance of the attributes, and conformance with HTA principles varied by region/country. Key issues and trends facing HTA bodies included standardizing methods for economic evaluations and grading of evidence, lack of evidence

Network optimization including gas lift and network parameters under subsurface uncertainty

Energy Technology Data Exchange (ETDEWEB)

Schulze-Riegert, R.; Baffoe, J.; Pajonk, O. [SPT Group GmbH, Hamburg (Germany); Badalov, H.; Huseynov, S. [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). ITE; Trick, M. [SPT Group, Calgary, AB (Canada)

2013-08-01

Optimization of oil and gas field production systems poses a great challenge to field development due to complex and multiple interactions between various operational design parameters and subsurface uncertainties. Conventional analytical methods are capable of finding local optima based on single deterministic models. They are less applicable for efficiently generating alternative design scenarios in a multi-objective context. Practical implementations of robust optimization workflows integrate the evaluation of alternative design scenarios and multiple realizations of subsurface uncertainty descriptions. Production or economic performance indicators such as NPV (Net Present Value) are linked to a risk-weighted objective function definition to guide the optimization processes. This work focuses on an integrated workflow using a reservoir-network simulator coupled to an optimization framework. The work will investigate the impact of design parameters while considering the physics of the reservoir, wells, and surface facilities. Subsurface uncertainties are described by well parameters such as inflow performance. Experimental design methods are used to investigate parameter sensitivities and interactions. Optimization methods are used to find optimal design parameter combinations which improve key performance indicators of the production network system. The proposed workflow will be applied to a representative oil reservoir coupled to a network which is modelled by an integrated reservoir-network simulator. Gas-lift will be included as an explicit measure to improve production. An objective function will be formulated for the net present value of the integrated system including production revenue and facility costs. Facility and gas lift design parameters are tuned to maximize NPV. Well inflow performance uncertainties are introduced with an impact on gas lift performance. Resulting variances on NPV are identified as a risk measure for the optimized system design. A

A Novel Method to Identify Differential Pathways in Hippocampus Alzheimer's Disease.

Science.gov (United States)

Liu, Chun-Han; Liu, Lian

2017-05-08

BACKGROUND Alzheimer's disease (AD) is the most common type of dementia. The objective of this paper is to propose a novel method to identify differential pathways in hippocampus AD. MATERIAL AND METHODS We proposed a combined method by merging existed methods. Firstly, pathways were identified by four known methods (DAVID, the neaGUI package, the pathway-based co-expressed method, and the pathway network approach), and differential pathways were evaluated through setting weight thresholds. Subsequently, we combined all pathways by a rank-based algorithm and called the method the combined method. Finally, common differential pathways across two or more of five methods were selected. RESULTS Pathways obtained from different methods were also different. The combined method obtained 1639 pathways and 596 differential pathways, which included all pathways gained from the four existing methods; hence, the novel method solved the problem of inconsistent results. Besides, a total of 13 common pathways were identified, such as metabolism, immune system, and cell cycle. CONCLUSIONS We have proposed a novel method by combining four existing methods based on a rank product algorithm, and identified 13 significant differential pathways based on it. These differential pathways might provide insight into treatment and diagnosis of hippocampus AD.

Dissipative Prototyping Methods: A Manifesto

Science.gov (United States)

Beesley, P.

Taking a designer's unique perspective using examples of practice in experimental installation and digital protoyping, this manifesto acts as provocation for change and unlocking new potential by encouraging changes of perspective about the material realm. Diffusive form-language is proposed as a paradigm for architectural design. This method of design is applied through 3D printing and related digital fabrication methods, offering new qualities that can be implemented in design of realms including present earth and future interplanetary environments. A paradigm shift is encouraged by questioning conventional notions of geometry that minimize interfaces and by proposing the alternatives of maximized interfaces formed by effusive kinds of formal composition. A series of projects from the Canadian research studio of the Hylozoic Architecture group are described, providing examples of component design methods employing diffusive forms within combinations of tension-integrity structural systems integrated with hybrid metabolisms employing synthetic biology. Cultural implications are also discussed, drawing from architectural theory and natural philosophy. The conclusion of this paper suggests that the practice of diffusive prototyping can offer formative strategies contributing to design of future living systems.

Efficient methods for including quantum effects in Monte Carlo calculations of large systems: extension of the displaced points path integral method and other effective potential methods to calculate properties and distributions.

Science.gov (United States)

Mielke, Steven L; Dinpajooh, Mohammadhasan; Siepmann, J Ilja; Truhlar, Donald G

2013-01-07

We present a procedure to calculate ensemble averages, thermodynamic derivatives, and coordinate distributions by effective classical potential methods. In particular, we consider the displaced-points path integral (DPPI) method, which yields exact quantal partition functions and ensemble averages for a harmonic potential and approximate quantal ones for general potentials, and we discuss the implementation of the new procedure in two Monte Carlo simulation codes, one that uses uncorrelated samples to calculate absolute free energies, and another that employs Metropolis sampling to calculate relative free energies. The results of the new DPPI method are compared to those from accurate path integral calculations as well as to results of two other effective classical potential schemes for the case of an isolated water molecule. In addition to the partition function, we consider the heat capacity and expectation values of the energy, the potential energy, the bond angle, and the OH distance. We also consider coordinate distributions. The DPPI scheme performs best among the three effective potential schemes considered and achieves very good accuracy for all of the properties considered. A key advantage of the effective potential schemes is that they display much lower statistical sampling variances than those for accurate path integral calculations. The method presented here shows great promise for including quantum effects in calculations on large systems.

New Directions in the NOAO Observing Proposal System

Science.gov (United States)

Gasson, David; Bell, Dave

For the past eight years NOAO has been refining its on-line observing proposal system. Virtually all related processes are now handled electronically. Members of the astronomical community can submit proposals through email, web form, or via the Gemini Phase I Tool. NOAO staff can use the system to do administrative tasks, scheduling, and compilation of various statistics. In addition, all information relevant to the TAC process is made available on-line, including the proposals themselves (in HTML, PDF and PostScript) and technical comments. Grades and TAC comments are entered and edited through web forms, and can be sorted and filtered according to specified criteria. Current developments include a move away from proprietary solutions, toward open standards such as SQL (in the form of the MySQL relational database system), Perl, PHP and XML.

The JET project (design proposal)

International Nuclear Information System (INIS)

1976-03-01

This proposal describes a large Tokamak experiment, which aims to study plasma behavior in conditions and dimensions approaching those required in a fusion reactor. The maximum plasma minor radius (a) is 1.25m and the major radius (R 0 ) is 2.96m. An important feature is the flexibility to study, for plasma currents in the 1→3MA range, a wide range of aspect ratios (R 0 /a=2.37→5), toroidal magnetic fields (up to 3.6T), minor radii (0.6→1.25m) and elongation ratios (b/a=1→3.5). The cost of the apparatus, power supplies, plasma heating equipment and specific diagnostics is estimated as 70.1Muc (march 1975 prices, 1uc=50FB). The total construction phase cost including commissioning, buildings and staff is 135Muc. These figures include an average overall contingency of 30%. The construction time for the project is estimated at 5 years and requires 370 professional man years of effort in the construction organisation with additional effort deployed by the Associated Laboratories in such areas as diagnostics and plasma heating. This design proposal is arranged as follows: an introduction to the field of fusion research is given and relates JET to the European and international programmes; a concise summary of the design proposal describes the objectives of research with JET, and gives a brief description of the apparatus, the cost and construction schedules, the proposed experimental programme and the possible modes of operation of the device. A detailed account of the engineering design and the staff and cost estimates is presented

Assessment methods for Bree-type ratcheting without the necessity of linearization of stresses and strains

International Nuclear Information System (INIS)

Fujioka, Terutaka

2015-01-01

This paper proposes methods for assessing Bree-type ratcheting in a cylinder subjected to constant internal pressure and cyclic thermal loading. The proposed methods are elastic analysis-route and elastic–plastic analysis-route. The former is based on the polynomial approximation of the elastic stress distributions for thermal stresses and the reference stress concept for estimating primary stress. The latter elastic–plastic route method is based on the concept of relative elastic core size. The methods proposed were validated by performing elastic–plastic finite element analyses of a smooth cylinder that exhibited Bree-type ratcheting. - Highlights: • Rationalization of the ratcheting assessment has been made. • The proposed methods include both elastic and elastic-plastic routes. • The elastic route method is based on skeletal point stress by elastic FEA. • The elastic-plastic route is based on elastic core size in elastic-plastic FEA. • These have been validated by elastic-plastic FEA causing Bree-type ratcheting

Understanding the unbundled utility conservation bidding proposal

International Nuclear Information System (INIS)

Joskow, P.L.

1990-01-01

For several years regulatory advisers have been engaged in controversy about the propriety of integrating energy conservation measures into the total resource planning processes of electric utilities, and of proposed methods of doing so in the competitive supply procurement programs which have been initiated by some utilities. Two prominent economists conceived a method for doing this in competitive bidding programs and at the same time overcoming objections to previous proposals which were based on perceived violations of basic economic principles. They explained their concept and its operation in an article published here in June of last year. In this article another economist subjects the concept to further analysis, identifying its essential elements, and point to inevitable results of their application

Multi-objective congestion management by modified augmented ε-constraint method

International Nuclear Information System (INIS)

Esmaili, Masoud; Shayanfar, Heidar Ali; Amjady, Nima

2011-01-01

Congestion management is a vital part of power system operations in recent deregulated electricity markets. However, after relieving congestion, power systems may be operated with a reduced voltage or transient stability margin because of hitting security limits or increasing the contribution of risky participants. Therefore, power system stability margins should be considered within the congestion management framework. The multi-objective congestion management provides not only more security but also more flexibility than single-objective methods. In this paper, a multi-objective congestion management framework is presented while simultaneously optimizing the competing objective functions of congestion management cost, voltage security, and dynamic security. The proposed multi-objective framework, called modified augmented ε-constraint method, is based on the augmented ε-constraint technique hybridized by the weighting method. The proposed framework generates candidate solutions for the multi-objective problem including only efficient Pareto surface enhancing the competitiveness and economic effectiveness of the power market. Besides, the relative importance of the objective functions is explicitly modeled in the proposed framework. Results of testing the proposed multi-objective congestion management method on the New-England test system are presented and compared with those of the previous single objective and multi-objective techniques in detail. These comparisons confirm the efficiency of the developed method. (author)

Emendation of the family Chlamydiaceae: proposal of a single genus, Chlamydia, to include all currently recognized species.

Science.gov (United States)

Sachse, Konrad; Bavoil, Patrik M; Kaltenboeck, Bernhard; Stephens, Richard S; Kuo, Cho-Chou; Rosselló-Móra, Ramon; Horn, Matthias

2015-03-01

The family Chlamydiaceae (order Chlamydiales, phylum Chlamydiae) comprises important, obligate intracellular bacterial pathogens of humans and animals. Subdivision of the family into the two genera Chlamydia and Chlamydophila has been discussed controversially during the past decade. Here, we have revisited the current classification in the light of recent genomic data and in the context of the unique biological properties of these microorganisms. We conclude that neither generally used 16S rRNA sequence identity cut-off values nor parameters based on genomic similarity consistently separate the two genera. Notably, no easily recognizable phenotype such as host preference or tissue tropism is available that would support a subdivision. In addition, the genus Chlamydophila is currently not well accepted and not used by a majority of research groups in the field. Therefore, we propose the classification of all 11 currently recognized Chlamydiaceae species in a single genus, the genus Chlamydia. Finally, we provide emended descriptions of the family Chlamydiaceae, the genus Chlamydia, as well as the species Chlamydia abortus, Chlamydia caviae and Chlamydia felis. Copyright © 2015 Elsevier GmbH. All rights reserved.

Development of an evaluation method for the quality of NPP MCR operators' communication using Work Domain Analysis (WDA)

International Nuclear Information System (INIS)

Jang, Inseok; Park, Jinkyun; Seong, Poonghyun

2011-01-01

Research highlights: → No evaluation method is available for operators' communication quality in NPPs. → To model this evaluation method, the Work Domain Analysis (WDA) method was found. → This proposed method was applied to NPP MCR operators. → The quality of operators' communication can be evaluated with the propose method. - Abstract: The evolution of work demands has seen industrial evolution itself evolve into the computerization of these demands, making systems more complex. This field is now known as the Complex Socio-Technical System. As communication failures are problems associated with Complex Socio-Technical Systems, it has been discovered that communication failures are the cause of many incidents and accidents in various industries, including the nuclear, aerospace and railway industries. Despite the fact that there have been many studies on the severity of communication failures, there is no evaluation method for operators' communication quality in Nuclear Power Plants (NPPs). Therefore, the objectives of this study are to develop an evaluation method for the quality of NPP Main Control Room (MCR) operators' communication and to apply the proposed method to operators in a full-scope simulator. To develop the proposed method, the Work Domain Analysis (WDA) method is introduced. Several characteristics of WDA, including Abstraction Decomposition Space (ADS) and the diagonal of ADS are the important points in developing an evaluation method for the quality of NPP MCR operators' communication. In addition, to apply the proposed method, nine teams working in NPPs participated in a field simulation. The results of this evaluation reveal that operators' communication quality improved as a greater proportion of the components in the developed evaluation criteria were mentioned. Therefore, the proposed method could be useful for evaluating the communication quality in any complex system.

Development of Extended Ray-tracing method including diffraction, polarization and wave decay effects

Science.gov (United States)

Yanagihara, Kota; Kubo, Shin; Dodin, Ilya; Nakamura, Hiroaki; Tsujimura, Toru

2017-10-01

Geometrical Optics Ray-tracing is a reasonable numerical analytic approach for describing the Electron Cyclotron resonance Wave (ECW) in slowly varying spatially inhomogeneous plasma. It is well known that the result with this conventional method is adequate in most cases. However, in the case of Helical fusion plasma which has complicated magnetic structure, strong magnetic shear with a large scale length of density can cause a mode coupling of waves outside the last closed flux surface, and complicated absorption structure requires a strong focused wave for ECH. Since conventional Ray Equations to describe ECW do not have any terms to describe the diffraction, polarization and wave decay effects, we can not describe accurately a mode coupling of waves, strong focus waves, behavior of waves in inhomogeneous absorption region and so on. For fundamental solution of these problems, we consider the extension of the Ray-tracing method. Specific process is planned as follows. First, calculate the reference ray by conventional method, and define the local ray-base coordinate system along the reference ray. Then, calculate the evolution of the distributions of amplitude and phase on ray-base coordinate step by step. The progress of our extended method will be presented.

Numerical simulation of GEW equation using RBF collocation method

Directory of Open Access Journals (Sweden)

Hamid Panahipour

2012-08-01

Full Text Available The generalized equal width (GEW equation is solved numerically by a meshless method based on a global collocation with standard types of radial basis functions (RBFs. Test problems including propagation of single solitons, interaction of two and three solitons, development of the Maxwellian initial condition pulses, wave undulation and wave generation are used to indicate the efficiency and accuracy of the method. Comparisons are made between the results of the proposed method and some other published numerical methods.

Double folding model including the Pauli exclusion principle

International Nuclear Information System (INIS)

Gridnev, K.A.; Soubbotin, V.B.; Oertzen, W. von; Bohlen, H.G.; Vinas, X.

2002-01-01

A new method to incorporate the Pauli principle into the double folding approach to the heavy ion potential is proposed. It is shown that in order to take into account the Pauli blocking a redefinition of the density matrices of the free isolated nuclei must be one. A solution to the self-consistent incorporation of the Pauli-blocking effects in the mean-field nucleus-nucleus potential is obtained in the Thomas-Fermi approximation [ru

Evaluation and Comparison of Multiple Test Methods, Including Real-time PCR, for Legionella Detection in Clinical Specimens

Science.gov (United States)

Peci, Adriana; Winter, Anne-Luise; Gubbay, Jonathan B.

2016-01-01

Legionella is a Gram-negative bacterium that can cause Pontiac fever, a mild upper respiratory infection and Legionnaire’s disease, a more severe illness. We aimed to compare the performance of urine antigen, culture, and polymerase chain reaction (PCR) test methods and to determine if sputum is an acceptable alternative to the use of more invasive bronchoalveolar lavage (BAL). Data for this study included specimens tested for Legionella at Public Health Ontario Laboratories from 1st January, 2010 to 30th April, 2014, as part of routine clinical testing. We found sensitivity of urinary antigen test (UAT) compared to culture to be 87%, specificity 94.7%, positive predictive value (PPV) 63.8%, and negative predictive value (NPV) 98.5%. Sensitivity of UAT compared to PCR was 74.7%, specificity 98.3%, PPV 77.7%, and NPV 98.1%. Out of 146 patients who had a Legionella-positive result by PCR, only 66 (45.2%) also had a positive result by culture. Sensitivity for culture was the same using either sputum or BAL (13.6%); sensitivity for PCR was 10.3% for sputum and 12.8% for BAL. Both sputum and BAL yield similar results regardless testing methods (Fisher Exact p-values = 1.0, for each test). In summary, all test methods have inherent weaknesses in identifying Legionella; therefore, more than one testing method should be used. Obtaining a single specimen type from patients with pneumonia limits the ability to diagnose Legionella, particularly when urine is the specimen type submitted. Given ease of collection and similar sensitivity to BAL, clinicians are encouraged to submit sputum in addition to urine when BAL submission is not practical from patients being tested for Legionella. PMID:27630979

A proposed programme for energy risk research

International Nuclear Information System (INIS)

1979-01-01

The report consists of two parts. Part I presents an overview of technological risk management, noting major contributions and current research needs. Part II details a proposed program of energy research, including discussions of some seven recommended projects. The proposed energy risk research program addresses two basic problem areas: improving the management of energy risks and energy risk communication and public response. Specific recommended projects are given for each. (Auth.)

Summary Report of Comprehensive Laboratory Testing to Establish the Effectiveness of Proposed Treatment Methods for Unremediated and Remediated Nitrate Salt Waste Streams

Energy Technology Data Exchange (ETDEWEB)

Anast, Kurt Roy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Funk, David John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hargis, Kenneth Marshall [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-04

The inadvertent creation of transuranic waste carrying hazardous waste codes D001 and D002 requires the treatment of the material to eliminate the hazardous characteristics and allow its eventual shipment and disposal at the Waste Isolation Pilot Plant (WIPP). This report documents the effectiveness of two treatment methods proposed to stabilize both the unremediated and remediated nitrate salt waste streams (UNS and RNS, respectively) at Los Alamos National Laboratory (LANL). The two technologies include the addition of zeolite (with and without the addition of water as a processing aid) and cementation. Surrogates were developed to evaluate both the solid and liquid fractions expected from parent waste containers, and both the solid and liquid fractions were tested. Both technologies are shown to be effective at eliminating the characteristic of ignitability (D001), and the addition of zeolite was determined to be effective at eliminating corrosivity (D002), with the preferred option1 of adding zeolite currently planned for implementation at LANL’s Waste Characterization, Reduction, and Repackaging Facility (WCRRF). The course of this work verified the need to evaluate and demonstrate the effectiveness of the proposed remedy for debris material, if required. The evaluation determined that WypAlls, cheesecloth, and Celotex absorbed with saturated nitrate salt solutions exhibit the ignitability characteristic (all other expected debris is not classified as ignitable). Finally, liquid surrogates containing saturated nitrate salts did not exhibit the characteristic of ignitability in their pure form (those neutralized with Kolorsafe and mixed with sWheat did exhibit D001). Sensitivity testing and an analysis were conducted to evaluate the waste form for reactivity. Tests included subjecting surrogate material to mechanical impact, friction, electrostatic discharge and thermal insults. The testing confirmed that the waste does not exhibit the characteristic of

Proposal of a simple screening method for a rapid preliminary evaluation of ''heavy metals'' mobility in soils of contaminated sites

Energy Technology Data Exchange (ETDEWEB)

Pinto, Valentina; Chiusolo, Francesca; Cremisini, Carlo [ENEA - Italian Agency for New Technologies, Energy and Environment, Rome (Italy). Section PROTCHIM

2010-09-15

Risks associated to ''heavy metals'' (HM) soil contamination depend not only on their total content but, mostly, on their mobility. Many extraction procedures have been developed to evaluate HM mobility in contaminated soils, but they are generally time consuming (especially the sequential extraction procedures (SEPs)) and consequently applicable on a limited number of samples. For this reason, a simple screening method, applicable even ''in field'', has been proposed in order to obtain a rapid evaluation of HM mobility in polluted soils, mainly focused on the fraction associated to Fe and Mn oxide/hydroxides. A buffer solution of trisodium citrate and hydroxylamine hydrochloride was used as extractant for a single-step leaching test. The choice of this buffered solution was strictly related to the possibility of directly determining, via titration with dithizone (DZ), the content of Zn, Cu, Pb and Cd, which are among the most representative contaminants in highly mineralised soils. Moreover, the extraction solution is similar, aside from for the pH value, which is the one used in the BCR SEP second step. The analysis of bivalents ions through DZ titration was exploited in order to further simplify and quicken the whole procedure. The proposed method generically measures, in few minutes, the concentration of total extractable ''heavy metals'' expressed as molL{sup -1} without distinguishing between elements. The proposed screening method has been developed and applied on soil samples collected from rural, urban and mining areas, representing different situation of soil contamination. Results were compared with data obtained from the BCR procedure. The screening method demonstrated to be a reliable tool for a rapid evaluation of metals mobility. Therefore, it could be very useful, even ''in field'', both to guide the sampling activity on site and to monitor the efficacy of the subsequent

Safety-relevant assessment concerning the proposals for investigations in proposed locations for stage 3 of the deep geological repositories project; Sicherheitstechnisches Gutachten zum Vorschlag der in Etappe 3 SGT weiter zu untersuchenden geologischen Standortgebiete - Sachplan geologische Tiefenlager, Etappe 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2017-04-15

This comprehensive report published by the Swiss Federal Nuclear Safety Inspectorate ENSI examines the proposals made by the Swiss National Cooperative for the disposal of Radioactive Waste (NAGRA) concerning proposed locations for deep waste repositories. Important basic considerations to be made when narrowing down the choice of host rock types and the selection of possible locations are discussed. These include, amongst others, safety concepts for the repositories, geological models and technical feasibility of repositories in Opalinus Clay, Brown Dogger layers and marl. The properties of various host rocks are discussed. Methods to be used in choosing at least two possible sites for repositories are considered. Also, the radioactive dosage to be expected at the various sites proposed is discussed. A safety-relevant comparison of the sites is made and an overall assessment is presented. The locations proposed for surface facilities at three proposed locations are discussed. The report is completed with an appendix containing tables and a list of relevant expert reports.

Proposal of Innovative Approaches of Relationship Marketing in Business

Directory of Open Access Journals (Sweden)

Viliam Lendel

2015-03-01

Full Text Available The aim of this paper is to propose innovative approaches to relationship marketing that affect the process of building relationships with customers, based on a detailed analysis of the literary sources and the research. This proposal is supported by the information technology e-CRM and social CRM. The paper contains a detailed description of the procedure for successfully implementing innovative approaches to relationship marketing in business. This should serve mainly to marketing managers as a valuable tool in their use of innovative approaches to relationship marketing, especially in the process of obtaining innovative ideas from customers, in order to identify their needs and requirements. Furthermore, the paper contains the main results of our research aimed at identifying the extent of utilization of innovative approaches to relationship marketing in Slovak businesses. A total of 207 respondents were involved in the research (medium and large businesses and following methods were used: comparative method of qualitative evaluation method, the method of structured and structured interview method, observation, document analysis method (method of content analysis and questionnaire method.

Security Techniques for Prevention of Rank Manipulation in Social Tagging Services including Robotic Domains

Directory of Open Access Journals (Sweden)

Okkyung Choi

2014-01-01

Full Text Available With smartphone distribution becoming common and robotic applications on the rise, social tagging services for various applications including robotic domains have advanced significantly. Though social tagging plays an important role when users are finding the exact information through web search, reliability and semantic relation between web contents and tags are not considered. Spams are making ill use of this aspect and put irrelevant tags deliberately on contents and induce users to advertise contents when they click items of search results. Therefore, this study proposes a detection method for tag-ranking manipulation to solve the problem of the existing methods which cannot guarantee the reliability of tagging. Similarity is measured for ranking the grade of registered tag on the contents, and weighted values of each tag are measured by means of synonym relevance, frequency, and semantic distances between tags. Lastly, experimental evaluation results are provided and its efficiency and accuracy are verified through them.

Security techniques for prevention of rank manipulation in social tagging services including robotic domains.

Science.gov (United States)

Choi, Okkyung; Jung, Hanyoung; Moon, Seungbin

2014-01-01

With smartphone distribution becoming common and robotic applications on the rise, social tagging services for various applications including robotic domains have advanced significantly. Though social tagging plays an important role when users are finding the exact information through web search, reliability and semantic relation between web contents and tags are not considered. Spams are making ill use of this aspect and put irrelevant tags deliberately on contents and induce users to advertise contents when they click items of search results. Therefore, this study proposes a detection method for tag-ranking manipulation to solve the problem of the existing methods which cannot guarantee the reliability of tagging. Similarity is measured for ranking the grade of registered tag on the contents, and weighted values of each tag are measured by means of synonym relevance, frequency, and semantic distances between tags. Lastly, experimental evaluation results are provided and its efficiency and accuracy are verified through them.

The Relationships Between Lost Work Time and Duration of Absence Spells: Proposal for a Payroll Driven Measure of Absenteeism

Science.gov (United States)

Hill, James J.; Slade, Martin D.; Cantley, Linda; Vegso, Sally; Fiellin, Martha; Cullen, Mark R.

2011-01-01

Objective To propose a standard measure of absenteeism (the work lost rate [WLR]) be included in future research to facilitate understanding and allow for translation of findings between scientific disciplines. Methods Hourly payroll data derived from “punch clock” reports was used to compare various measures of absenteeism used in the literature and the application of the proposed metric (N = 4000 workers). Results Unpaid hours and full absent days were highly correlated with the WLR (r = 0.896 to 0.898). The highest percentage of unpaid hours (lost work time) is captured by absence spells of 1 and 2 days duration. Conclusion The proposed WLR metric captures: 1) The range and distribution of the individual WLRs, 2) the percentage of subjects with no unpaid hours, and 3) the population WLR and should be included whenever payroll data is used to measure absenteeism. PMID:18617841

A scoring system for appraising mixed methods research, and concomitantly appraising qualitative, quantitative and mixed methods primary studies in Mixed Studies Reviews.

Science.gov (United States)

Pluye, Pierre; Gagnon, Marie-Pierre; Griffiths, Frances; Johnson-Lafleur, Janique

2009-04-01

A new form of literature review has emerged, Mixed Studies Review (MSR). These reviews include qualitative, quantitative and mixed methods studies. In the present paper, we examine MSRs in health sciences, and provide guidance on processes that should be included and reported. However, there are no valid and usable criteria for concomitantly appraising the methodological quality of the qualitative, quantitative and mixed methods studies. To propose criteria for concomitantly appraising the methodological quality of qualitative, quantitative and mixed methods studies or study components. A three-step critical review was conducted. 2322 references were identified in MEDLINE, and their titles and abstracts were screened; 149 potentially relevant references were selected and the full-text papers were examined; 59 MSRs were retained and scrutinized using a deductive-inductive qualitative thematic data analysis. This revealed three types of MSR: convenience, reproducible, and systematic. Guided by a proposal, we conducted a qualitative thematic data analysis of the quality appraisal procedures used in the 17 systematic MSRs (SMSRs). Of 17 SMSRs, 12 showed clear quality appraisal procedures with explicit criteria but no SMSR used valid checklists to concomitantly appraise qualitative, quantitative and mixed methods studies. In two SMSRs, criteria were developed following a specific procedure. Checklists usually contained more criteria than needed. In four SMSRs, a reliability assessment was described or mentioned. While criteria for quality appraisal were usually based on descriptors that require specific methodological expertise (e.g., appropriateness), no SMSR described the fit between reviewers' expertise and appraised studies. Quality appraisal usually resulted in studies being ranked by methodological quality. A scoring system is proposed for concomitantly appraising the methodological quality of qualitative, quantitative and mixed methods studies for SMSRs. This

Text-in-context: a method for extracting findings in mixed-methods mixed research synthesis studies.

Science.gov (United States)

Sandelowski, Margarete; Leeman, Jennifer; Knafl, Kathleen; Crandell, Jamie L

2013-06-01

Our purpose in this paper is to propose a new method for extracting findings from research reports included in mixed-methods mixed research synthesis studies. International initiatives in the domains of systematic review and evidence synthesis have been focused on broadening the conceptualization of evidence, increased methodological inclusiveness and the production of evidence syntheses that will be accessible to and usable by a wider range of consumers. Initiatives in the general mixed-methods research field have been focused on developing truly integrative approaches to data analysis and interpretation. The data extraction challenges described here were encountered, and the method proposed for addressing these challenges was developed, in the first year of the ongoing (2011-2016) study: Mixed-Methods Synthesis of Research on Childhood Chronic Conditions and Family. To preserve the text-in-context of findings in research reports, we describe a method whereby findings are transformed into portable statements that anchor results to relevant information about sample, source of information, time, comparative reference point, magnitude and significance and study-specific conceptions of phenomena. The data extraction method featured here was developed specifically to accommodate mixed-methods mixed research synthesis studies conducted in nursing and other health sciences, but reviewers might find it useful in other kinds of research synthesis studies. This data extraction method itself constitutes a type of integration to preserve the methodological context of findings when statements are read individually and in comparison to each other. © 2012 Blackwell Publishing Ltd.

A new method used to evaluate organic working fluids

International Nuclear Information System (INIS)

Zhang, Xinxin; He, Maogang; Wang, Jingfu

2014-01-01

In this paper, we propose a method named “Weight Classification-Hasse Dominance” to evaluate organic working fluids. This new method combines the advantages of both the method of weight determination and the Hasse Diagram Technique (HDT). It can be used to evaluate the thermodynamic performance, environmental protection indicator, and safety requirement of organic working fluid simultaneously. This evaluation method can offer good reference for working fluid selection. Using this method, the organic working fluids which have been phased out and will be phased out by the Montreal Protocol including CFCs (chlorofluorocarbons), HCFCs (hydrochlorofluorocarbons), and HFCs (hydrofluorocarbons) were evaluated. Moreover, HCs (hydrocarbons) can be considered as a completely different kind of organic working fluid from CFCs, HCFCs, and HFCs according to the comparison based on this new evaluation method. - Highlights: • We propose a new method used to evaluate organic working fluids. • This evaluation method can offer good reference for working fluid selection. • CFC, HCFC, and HFC working fluids were evaluated using this evaluation method. • HC can be considered as a totally different working fluid from CFC, HCFC, and HFC

Analysis of random response of structure with uncertain parameters. Combination of substructure synthesis method and hierarchy method

International Nuclear Information System (INIS)

Iwatsubo, Takuzo; Kawamura, Shozo; Mori, Hiroyuki.

1995-01-01

In this paper, the method to obtain the random response of a structure with uncertain parameters is proposed. The proposed method is a combination of the substructure synthesis method and the hierarchy method. The concept of the proposed method is that the hierarchy equation of each substructure is obtained using the hierarchy method, and the hierarchy equation of the overall structure is obtained using the substructure synthesis method. Using the proposed method, the reduced order hierarchy equation can be obtained without analyzing the original whole structure. After the calculation of the mean square value of response, the reliability analysis can be carried out based on the first passage problem and Poisson's excursion rate. As a numerical example of structure, a simple piping system is considered. The damping constant of the support is considered as the uncertainty parameter. Then the random response is calculated using the proposed method. As a result, the proposed method is useful to analyze the random response in terms of the accuracy, computer storage and calculation time. (author)

The Method of Lines Solution of the Regularized Long-Wave Equation Using Runge-Kutta Time Discretization Method

Directory of Open Access Journals (Sweden)

H. O. Bakodah

2013-01-01

Full Text Available A method of lines approach to the numerical solution of nonlinear wave equations typified by the regularized long wave (RLW is presented. The method developed uses a finite differences discretization to the space. Solution of the resulting system was obtained by applying fourth Runge-Kutta time discretization method. Using Von Neumann stability analysis, it is shown that the proposed method is marginally stable. To test the accuracy of the method some numerical experiments on test problems are presented. Test problems including solitary wave motion, two-solitary wave interaction, and the temporal evaluation of a Maxwellian initial pulse are studied. The accuracy of the present method is tested with and error norms and the conservation properties of mass, energy, and momentum under the RLW equation.

75 FR 48659 - Notice of Proposed Information Collection Requests

Science.gov (United States)

2010-08-11

..., including through the use of information technology. Dated: August 5, 2010. James Hyler, Acting Director... notify the school about the upcoming data collection. Requests for copies of the proposed information... DEPARTMENT OF EDUCATION Notice of Proposed Information Collection Requests AGENCY: Department of...

Elliptic equation rational expansion method and new exact travelling solutions for Whitham-Broer-Kaup equations

International Nuclear Information System (INIS)

Chen Yong; Wang Qi; Li Biao

2005-01-01

Based on a new general ansatz and a general subepuation, a new general algebraic method named elliptic equation rational expansion method is devised for constructing multiple travelling wave solutions in terms of rational special function for nonlinear evolution equations (NEEs). We apply the proposed method to solve Whitham-Broer-Kaup equation and explicitly construct a series of exact solutions which include rational form solitary wave solution, rational form triangular periodic wave solutions and rational wave solutions as special cases. In addition, the links among our proposed method with the method by Fan [Chaos, Solitons and Fractals 2004;20:609], are also clarified generally

On Self-Adaptive Method for General Mixed Variational Inequalities

Directory of Open Access Journals (Sweden)

Abdellah Bnouhachem

2008-01-01

Full Text Available We suggest and analyze a new self-adaptive method for solving general mixed variational inequalities, which can be viewed as an improvement of the method of (Noor 2003. Global convergence of the new method is proved under the same assumptions as Noor's method. Some preliminary computational results are given to illustrate the efficiency of the proposed method. Since the general mixed variational inequalities include general variational inequalities, quasivariational inequalities, and nonlinear (implicit complementarity problems as special cases, results proved in this paper continue to hold for these problems.

New transmission planning methodology for requesting proposals for wind generation

Science.gov (United States)

Isaacs, Andrew L.

The increasing interest in renewable energy technologies during the last decade has caused conventional transmission and generation expansion planning methodologies to be strained and in some cases abandoned. This is due both to the quantity of generator interconnection requests and the constraints imposed by deregulated energy industry structures. One technique used to control the influx of renewable generation while maintaining competitive principles is a Request for Proposals (RFP). However, lack of transmission planning due to a disconnection between generation and transmission owners, difficulty in identifying viable projects, and high risk for proponents stand as obstacles to the goals of an RFP. This research proposes a procedure which minimizes the effect of these obstacles; meeting the purchaser requirements for low price and combining conventional planning concepts with feedback from competitive structures. The general features of the method include definition of generation limits and study area, expansion plan design, transmission cost evaluation, optimal selection of requested generation levels, and final selection of successful proponents. The method is shown to be effective in creating an RFP where proponents are well-informed and provided with cost certainty to reduce bid price, buyers are able to determine end costs of their energy, and good expansion planning principles are maintained. A case study using a real system in New Mexico demonstrates these concepts.

Proposal of secure camera-based radiation warning system for nuclear detection

International Nuclear Information System (INIS)

Tsuchiya, Ken'ichi; Kurosawa, Kenji; Akiba, Norimitsu; Kakuda, Hidetoshi; Imoto, Daisuke; Hirabayashi, Manato; Kuroki, Kenro

2016-01-01

Counter-terrorisms against radiological and nuclear threat are significant issues toward Tokyo 2020 Olympic and Paralympic Games. In terms of cost benefit, it is not easy to build a warning system for nuclear detection to prevent a Dirty Bomb attack (dispersion of radioactive materials using a conventional explosive) or a Silent Source attack (hidden radioactive materials) from occurring. We propose a nuclear detection system using the installed secure cameras. We describe a method to estimate radiation dose from noise pattern in CCD images caused by radiation. Some dosimeters under neutron and gamma-ray irradiations (0.1mSv-100mSv) were taken in CCD video camera. We confirmed amount of noise in CCD images increased in radiation exposure. The radiation detection using CMOS in secure cameras or cell phones has been implemented. However, in this presentation, we propose a warning system including neutron detection to search shielded nuclear materials or radiation exposure devices using criticality. (author)

Cross-Cultural Adaptation and Validation of the MPAM-R to Brazilian Portuguese and Proposal of a New Method to Calculate Factor Scores

Science.gov (United States)

Albuquerque, Maicon R.; Lopes, Mariana C.; de Paula, Jonas J.; Faria, Larissa O.; Pereira, Eveline T.; da Costa, Varley T.

2017-01-01

In order to understand the reasons that lead individuals to practice physical activity, researchers developed the Motives for Physical Activity Measure-Revised (MPAM-R) scale. In 2010, a translation of MPAM-R to Portuguese and its validation was performed. However, psychometric measures were not acceptable. In addition, factor scores in some sports psychology scales are calculated by the mean of scores by items of the factor. Nevertheless, it seems appropriate that items with higher factor loadings, extracted by Factor Analysis, have greater weight in the factor score, as items with lower factor loadings have less weight in the factor score. The aims of the present study are to translate, validate the MPAM-R for Portuguese versions, and investigate agreement between two methods used to calculate factor scores. Three hundred volunteers who were involved in physical activity programs for at least 6 months were collected. Confirmatory Factor Analysis of the 30 items indicated that the version did not fit the model. After excluding four items, the final model with 26 items showed acceptable model fit measures by Exploratory Factor Analysis, as well as it conceptually supports the five factors as the original proposal. When two methods are compared to calculate factors scores, our results showed that only “Enjoyment” and “Appearance” factors showed agreement between methods to calculate factor scores. So, the Portuguese version of the MPAM-R can be used in a Brazilian context, and a new proposal for the calculation of the factor score seems to be promising. PMID:28293203

Indication of Importance of Including Soil Microbial Characteristics into Biotope Valuation Method.

Czech Academy of Sciences Publication Activity Database

Trögl, J.; Pavlorková, Jana; Packová, P.; Seják, J.; Kuráň, P.; Kuráň, J.; Popelka, J.; Pacina, J.

2016-01-01

Roč. 8, č. 3 (2016), č. článku 253. ISSN 2071-1050 Institutional support: RVO:67985858 Keywords : biotope assessment * biotope valuation method * soil microbial communities Subject RIV: DJ - Water Pollution ; Quality Impact factor: 1.789, year: 2016

77 FR 76588 - Request for Proposal Platform Pilot

Science.gov (United States)

2012-12-28

... businesses, including start-up small businesses considering the federal marketplace (new entrants), and those... easier for small businesses, including ``new entrant'' small businesses that have historically not done... SMALL BUSINESS ADMINISTRATION [Docket Number SBA 2012-0019] Request for Proposal Platform Pilot...

Nonparametric Inference of Doubly Stochastic Poisson Process Data via the Kernel Method.

Science.gov (United States)

Zhang, Tingting; Kou, S C

2010-01-01

Doubly stochastic Poisson processes, also known as the Cox processes, frequently occur in various scientific fields. In this article, motivated primarily by analyzing Cox process data in biophysics, we propose a nonparametric kernel-based inference method. We conduct a detailed study, including an asymptotic analysis, of the proposed method, and provide guidelines for its practical use, introducing a fast and stable regression method for bandwidth selection. We apply our method to real photon arrival data from recent single-molecule biophysical experiments, investigating proteins' conformational dynamics. Our result shows that conformational fluctuation is widely present in protein systems, and that the fluctuation covers a broad range of time scales, highlighting the dynamic and complex nature of proteins' structure.

The JET Project (Design proposal)

International Nuclear Information System (INIS)

1976-01-01

This proposal describes a large Tokamak experiment, which aims to study plasma behavior in conditions and dimensions approaching those required in a fusion reactor. The maximum plasma minor radius (a) is 1.25 m and the major radius R 0 is 2.96 m. An important feature is the flexibility to study, for plasma currents in the 1→3 MA range, a wide range of aspect ratios R 0 /a=2.37→5), toroidal magnetic fields (up to 3.6T), minor radii (0.6→1.25 m) and elongation ratios (b/a=1→3.5). The cost of the apparatus, power supplies, plasma heating equipment and specific diagnostics is estimated as 70.1 Muc (March 1975 prices, 1 uc=50 FB). The total construction phase cost including commissioning, buildings and staff is 135 Muc. These figures include an average overall contingency of 30%. The construction time for the project is estimated at 5 years and requires 370 professional man years of effort in the construction organisation with additional effort deployed by the Associated Laboratories in such areas as diagnostics and plasma heating. This design proposal is arranged as follows: The preface gives an introduction to the field of fusion research and relates JET to the European and international programmes. Chapter I is a concise summary of the design proposal, it describes the objectives of research with JET, and gives a brief description of: the apparatus; the cost and construction schedules; the proposed experimental programme and the possible modes of operation of the device. A detailed account of the project is given in the rest of the report of which Chapters IV and VII comprise the engineering design and the staff and cost estimates respectively

Effects of disease severity distribution on the performance of quantitative diagnostic methods and proposal of a novel 'V-plot' methodology to display accuracy values.

Science.gov (United States)

Petraco, Ricardo; Dehbi, Hakim-Moulay; Howard, James P; Shun-Shin, Matthew J; Sen, Sayan; Nijjer, Sukhjinder S; Mayet, Jamil; Davies, Justin E; Francis, Darrel P

2018-01-01

Diagnostic accuracy is widely accepted by researchers and clinicians as an optimal expression of a test's performance. The aim of this study was to evaluate the effects of disease severity distribution on values of diagnostic accuracy as well as propose a sample-independent methodology to calculate and display accuracy of diagnostic tests. We evaluated the diagnostic relationship between two hypothetical methods to measure serum cholesterol (Chol rapid and Chol gold ) by generating samples with statistical software and (1) keeping the numerical relationship between methods unchanged and (2) changing the distribution of cholesterol values. Metrics of categorical agreement were calculated (accuracy, sensitivity and specificity). Finally, a novel methodology to display and calculate accuracy values was presented (the V-plot of accuracies). No single value of diagnostic accuracy can be used to describe the relationship between tests, as accuracy is a metric heavily affected by the underlying sample distribution. Our novel proposed methodology, the V-plot of accuracies, can be used as a sample-independent measure of a test performance against a reference gold standard.

A fast method for optimal reactive power flow solution

Energy Technology Data Exchange (ETDEWEB)

Sadasivam, G; Khan, M A [Anna Univ., Madras (IN). Coll. of Engineering

1990-01-01

A fast successive linear programming (SLP) method for minimizing transmission losses and improving the voltage profile is proposed. The method uses the same compactly stored, factorized constant matrices in all the LP steps, both for power flow solution and for constructing the LP model. The inherent oscillatory convergence of SLP methods is overcome by proper selection of initial step sizes and their gradual reduction. Detailed studies on three systems, including a 109-bus system, reveal the fast and reliable convergence property of the method. (author).

A numerical method for interaction problems between fluid and membranes with arbitrary permeability for fluid

Science.gov (United States)

Miyauchi, Suguru; Takeuchi, Shintaro; Kajishima, Takeo

2017-09-01

We develop a numerical method for fluid-membrane interaction accounting for permeation of the fluid using a non-conforming mesh to the membrane shape. To represent the permeation flux correctly, the proposed finite element discretization incorporates the discontinuities in the velocity gradient and pressure on the membrane surface with specially selected base functions. The discontinuities are represented with independent variables and determined to satisfy the governing equations including the interfacial condition on the permeation. The motions of the fluid, membrane and permeation flux are coupled monolithically and time-advanced fully-implicitly. The validity and effectiveness of the proposed method are demonstrated by several two-dimensional fluid-membrane interaction problems of Stokes flows by comparing with the analytical models and numerical results obtained by other methods. The reproduced sharp discontinuities are found to be essential to suppress the non-physical permeation flux. Further, combined with the numerical treatment for the solute concentration across the membrane, the proposed method is applied to a fluid-structure interaction problem including the osmotic pressure difference.

How to identify partial exposures to ionizing radiation? Proposal for a cytogenetic method

International Nuclear Information System (INIS)

Fernandes, T.S.; Silva, E.B.; Pinto, M.M.P.L.; Amaral, A.; Lloyd, David

2013-01-01

In cases of radiological incidents or in occupational exposures to ionizing radiation, the majority of exposures are not related to the total body, but only partial. In this context, if the cytogenetic dosimetry is performed, there will be an underestimation of the absorbed dose due to the dilution of irradiated cells with non-irradiated cells. Considering the norms of NR 32 - Safety and Health in the Work of Health Service - which recommends cytogenetic dosimetry in the investigation of accidental exposures to ionizing radiations, it is necessary to develop of a tool to provide a better identification of partial exposures. With this aim, a partial body exposure was simulated by mixing, in vitro, 70% of blood irradiated with 4 Gy of X-rays with 30% of unirradiated blood from the same healthy donor. Aliquots of this mixture were cultured for 48 and 72 hours. Prolonging the time of cell culture from 48 to 72 hours produced no significant change in the yield of dicentrics. However, when only M1 (first division cells) were analyzed, the frequency of dicentrics per cell was increased. Prolonging the time of cell culture allowed cells in mitotic delay by irradiation to reach metaphase, and thus provides enough time for the damage to be visualized. The results of this research present the proposed method as an important tool in the investigation of exposed individuals, allowing associating the cytogenetic analysis with the real percentage of irradiated cells, contributing significantly for the decision making in terms of occupational health. (author)

Proposed Objective Odor Control Test Methodology for Waste Containment

Science.gov (United States)

Vos, Gordon

2010-01-01

The Orion Cockpit Working Group has requested that an odor control testing methodology be proposed to evaluate the odor containment effectiveness of waste disposal bags to be flown on the Orion Crew Exploration Vehicle. As a standardized "odor containment" test does not appear to be a matter of record for the project, a new test method is being proposed. This method is based on existing test methods used in industrial hygiene for the evaluation of respirator fit in occupational settings, and takes into consideration peer reviewed documentation of human odor thresholds for standardized contaminates, industry stardnard atmostpheric testing methodologies, and established criteria for laboratory analysis. The proposed methodology is quantitative, though it can readily be complimented with a qualitative subjective assessment. Isoamyl acetate (IAA - also known at isopentyl acetate) is commonly used in respirator fit testing, and there are documented methodologies for both measuring its quantitative airborne concentrations. IAA is a clear, colorless liquid with a banana-like odor, documented detectable smell threshold for humans of 0.025 PPM, and a 15 PPB level of quantation limit.

Programming in a proposed 9X distributed Ada

Science.gov (United States)

Waldrop, Raymond S.; Volz, Richard A.; Goldsack, Stephen J.; Holzbach-Valero, A. A.

1991-01-01

The studies of the proposed Ada 9X constructs for distribution, now referred to as AdaPT are reported. The goals for this time period were to revise the chosen example scenario and to begin studying about how the proposed constructs might be implemented. The example scenario chosen is the Submarine Combat Information Center (CIC) developed by IBM for the Navy. The specification provided by IBM was preliminary and had several deficiencies. To address these problems, some changes to the scenario specification were made. Some of the more important changes include: (1) addition of a system database management function; (2) addition of a fourth processing unit to the standard resources; (3) addition of an operator console interface function; and (4) removal of the time synchronization function. To implement the CIC scenario in AdaPT, the decided strategy were publics, partitions, and nodes. The principle purpose for implementing the CIC scenario was to demonstrate how the AdaPT constructs interact with the program structure. While considering ways that the AdaPt constructs might be translated to Ada 83, it was observed that the partition construct could reasonably be modeled as an abstract data type. Although this gives a useful method of modeling partitions, it does not at all address the configuration aspects on the node construct.

Binary Classification Method of Social Network Users

Directory of Open Access Journals (Sweden)

I. A. Poryadin

2017-01-01

Full Text Available The subject of research is a binary classification method of social network users based on the data analysis they have placed. Relevance of the task to gain information about a person by examining the content of his/her pages in social networks is exemplified. The most common approach to its solution is a visual browsing. The order of the regional authority in our country illustrates that its using in school education is needed. The article shows restrictions on the visual browsing of pupil’s pages in social networks as a tool for the teacher and the school psychologist and justifies that a process of social network users’ data analysis should be automated. Explores publications, which describe such data acquisition, processing, and analysis methods and considers their advantages and disadvantages. The article also gives arguments to support a proposal to study the classification method of social network users. One such method is credit scoring, which is used in banks and credit institutions to assess the solvency of clients. Based on the high efficiency of the method there is a proposal for significant expansion of its using in other areas of society. The possibility to use logistic regression as the mathematical apparatus of the proposed method of binary classification has been justified. Such an approach enables taking into account the different types of data extracted from social networks. Among them: the personal user data, information about hobbies, friends, graphic and text information, behaviour characteristics. The article describes a number of existing methods of data transformation that can be applied to solve the problem. An experiment of binary gender-based classification of social network users is described. A logistic model obtained for this example includes multiple logical variables obtained by transforming the user surnames. This experiment confirms the feasibility of the proposed method. Further work is to define a system

The grant writer's handbook how to write a research proposal and succeed

CERN Document Server

Crawley, Gerard M

2016-01-01

The Grant Writer's Handbook: How to Write a Research Proposal and Succeed provides useful and practical advice on all aspects of proposal writing, including developing proposal ideas, drafting the proposal, dealing with referees, and budgeting. The authors base their advice on many years of experience writing and reviewing proposals in many different countries at various levels of scientific maturity. The book describes the numerous kinds of awards available from funding agencies, in particular large collaborative grants involving a number of investigators, and addresses the practical impact of a grant, which is often required of proposals. In addition, information is provided about selection of reviewers and the mechanics of organizing a research grant competition to give the proposal writer the necessary background information. The book includes key comments from a number of experts and is essential reading for anyone writing a research grant proposal.The Grant Writer's Handbook's companion website, featuri...

Preface of "The Second Symposium on Border Zones Between Experimental and Numerical Application Including Solution Approaches By Extensions of Standard Numerical Methods"

Science.gov (United States)

Ortleb, Sigrun; Seidel, Christian

2017-07-01

In this second symposium at the limits of experimental and numerical methods, recent research is presented on practically relevant problems. Presentations discuss experimental investigation as well as numerical methods with a strong focus on application. In addition, problems are identified which require a hybrid experimental-numerical approach. Topics include fast explicit diffusion applied to a geothermal energy storage tank, noise in experimental measurements of electrical quantities, thermal fluid structure interaction, tensegrity structures, experimental and numerical methods for Chladni figures, optimized construction of hydroelectric power stations, experimental and numerical limits in the investigation of rain-wind induced vibrations as well as the application of exponential integrators in a domain-based IMEX setting.

Equal Opportunity for Children (A Proposal for Licensed Parenthood).

Science.gov (United States)

Rogers, Cosby S.; Hicks, Mary W.

A theoretical proposal for a government-sponsored system of licensed parenthood is suggested, based on the premise that overpopulation, child abuse, and emotional, intellectual, and physical handicaps in children could be controlled through legislation. The three-part legislative proposal for licensed parenthood outlined would include: (1)…

Writing a Research Proposal to The Research Council of Oman

OpenAIRE

Al-Shukaili, Ahmed; Al-Maniri, Abdullah

2017-01-01

Writing a research proposal can be a challenging task for young researchers. This article explains how to write a strong research proposal to apply for funding, specifically, a proposal for The Research Council (TRC) of Oman. Three different research proposal application forms are currently used in TRC, including Open Research Grant (ORG), Graduate Research Support Program (GRSP), and Faculty-mentored Undergraduate Research Award Program (FURAP). The application forms are filled and submitted...

SU-E-J-89: Deformable Registration Method Using B-TPS in Radiotherapy.

Science.gov (United States)

Xie, Y

2012-06-01

A novel deformable registration method for four-dimensional computed tomography (4DCT) images is developed in radiation therapy. The proposed method combines the thin plate spline (TPS) and B-spline together to achieve high accuracy and high efficiency. The method consists of two steps. First, TPS is used as a global registration method to deform large unfit regions in the moving image to match counterpart in the reference image. Then B-spline is used for local registration, the previous deformed moving image is further deformed to match the reference image more accurately. Two clinical CT image sets, including one pair of lung and one pair of liver, are simulated using the proposed algorithm, which results in a tremendous improvement in both run-time and registration quality, compared with the conventional methods solely using either TPS or B-spline. The proposed method can combine the efficiency of TPS and the accuracy of B-spline, performing good adaptively and robust in registration of clinical 4DCT image. © 2012 American Association of Physicists in Medicine.

A homogenization method for ductile-brittle composite laminates at large deformations

DEFF Research Database (Denmark)

Poulios, Konstantinos; Niordson, Christian Frithiof

2018-01-01

-elastic behavior in the reinforcement as well as for the bending stiffness of the reinforcement layers. Additionally to previously proposed models, the present method includes Lemaitre type damage for the reinforcement, making it applicable to a wider range of engineering applications. The capability...... of the proposed method in representing the combined effect of plasticity, damage and buckling at microlevel within a homogenized setting is demonstrated by means of direct comparisons to a reference discrete model.......This paper presents a high fidelity homogenization method for periodically layered composite structures that accounts for plasticity in the matrix material and quasi-brittle damage in the reinforcing layers, combined with strong geometrical nonlinearities. A set of deliberately chosen internal...

REQUEST FOR PROPOSAL (RFP) Amendment

International Development Research Centre (IDRC) Digital Library (Canada)

Jayne Bassett

2013-08-01

Aug 1, 2013 ... HEAD OFFICE / SIÈGE : 150 Kent Street / 150, rue Kent PO Box / CP 8500 Ottawa ON Canada K1G 3H9 ... Areas of Study. It is understood that the applicant must submit a comprehensive and detailed proposal in one, two, or three areas of study, which include: public health, agriculture and food ...

Deterministic factor analysis: methods of integro-differentiation of non-integral order

Directory of Open Access Journals (Sweden)

Valentina V. Tarasova

2016-12-01

Full Text Available Objective to summarize the methods of deterministic factor economic analysis namely the differential calculus and the integral method. nbsp Methods mathematical methods for integrodifferentiation of nonintegral order the theory of derivatives and integrals of fractional nonintegral order. Results the basic concepts are formulated and the new methods are developed that take into account the memory and nonlocality effects in the quantitative description of the influence of individual factors on the change in the effective economic indicator. Two methods are proposed for integrodifferentiation of nonintegral order for the deterministic factor analysis of economic processes with memory and nonlocality. It is shown that the method of integrodifferentiation of nonintegral order can give more accurate results compared with standard methods method of differentiation using the first order derivatives and the integral method using the integration of the first order for a wide class of functions describing effective economic indicators. Scientific novelty the new methods of deterministic factor analysis are proposed the method of differential calculus of nonintegral order and the integral method of nonintegral order. Practical significance the basic concepts and formulas of the article can be used in scientific and analytical activity for factor analysis of economic processes. The proposed method for integrodifferentiation of nonintegral order extends the capabilities of the determined factorial economic analysis. The new quantitative method of deterministic factor analysis may become the beginning of quantitative studies of economic agents behavior with memory hereditarity and spatial nonlocality. The proposed methods of deterministic factor analysis can be used in the study of economic processes which follow the exponential law in which the indicators endogenous variables are power functions of the factors exogenous variables including the processes

77 FR 54620 - Proposed Collection; Comment Request

Science.gov (United States)