RH Packaging Program Guidance

International Nuclear Information System (INIS)

2008-01-01

The purpose of this program guidance document is to provide the technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package (also known as the 'RH-TRU 72-B cask') and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the C of C shall govern. The C of C states: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' It further states: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M and O) Contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8, 'Deliberate Misconduct.' Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, 'Packaging and Transportation of Radioactive Material,' certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21, 'Reporting of Defects and Noncompliance,' regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous

RH Packaging Program Guidance

International Nuclear Information System (INIS)

2006-01-01

The purpose of this program guidance document is to provide the technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the C of C shall govern. The C of C states: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' It further states: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M and O) Contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 Code of Federal Regulations (CFR) 1.8, 'Deliberate Misconduct.' Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, 'Packaging and Transportation of Radioactive Material,' certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21, 'Reporting of Defects and Noncompliance,' regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these

76 FR 74834 - Interim Staff Guidance on Aging Management Program for Steam Generators

Science.gov (United States)

2011-12-01

... for Steam Generators AGENCY: Nuclear Regulatory Commission. ACTION: Interim staff guidance; issuance... (LR-ISG), LR-ISG-2011-02, ``Aging Management Program for Steam Generators.'' This LR-ISG provides the...) document, NEI 97-06, ``Steam Generator Program Guidelines,'' (NRC's Agencywide Documents Access and...

Guidance Document on Standardised Test Guidelines for Evaluating Chemicals for Endocrine Disruption

DEFF Research Database (Denmark)

Satya, Sneha; Wade, Mike; Hass, Ulla

This guidance document was developed as a follow-up to the workshop on OECD countries’ activities regarding testing, assessment and management of endocrine disrupters, which was held in Copenhagen (Denmark) on 22-24 September 2010 (see document No. 118 published in the Series on Testing and Asses......This guidance document was developed as a follow-up to the workshop on OECD countries’ activities regarding testing, assessment and management of endocrine disrupters, which was held in Copenhagen (Denmark) on 22-24 September 2010 (see document No. 118 published in the Series on Testing...... on testing and assessment of endocrine disrupters (EDTA AG). In November 2010, comments were requested from the WNT, the EDTA AG, the Task Force on Hazard Assessment and experts involved in the assessment of chemicals. The EDTA AG addressed the comments from the WNT at a meeting held in April 2011...... the conclusions and next steps recommended in the draft guidance document are sensible and helpful when assessed in light of comprehensive datasets. The draft guidance document and the three case studies were reviewed again and revised at a meeting of the EDTA AG in December 2011. The draft guidance document...

76 FR 411 - Regulatory Guidance Concerning Electronic Signatures and Documents

Science.gov (United States)

2011-01-04

... guidance, including memoranda and letters, may no longer be relied upon to the extent they are inconsistent... Concerning Electronic Signatures and Documents AGENCY: Federal Motor Carrier Safety Administration (FMCSA), DOT. ACTION: Notice of regulatory guidance. SUMMARY: FMCSA issues regulatory guidance concerning the...

21 CFR 601.29 - Guidance documents.

Science.gov (United States)

2010-04-01

... Manufacturers Assistance (HFM-40), Center for Biologics Evaluation and Research, Food and Drug Administration... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Guidance documents. 601.29 Section 601.29 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS...

Guidance and Control Software Project Data - Volume 1: Planning Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the planning documents from the GCS project. Volume 1 contains five appendices: A. Plan for Software Aspects of Certification for the Guidance and Control Software Project; B. Software Development Standards for the Guidance and Control Software Project; C. Software Verification Plan for the Guidance and Control Software Project; D. Software Configuration Management Plan for the Guidance and Control Software Project; and E. Software Quality Assurance Activities.

Guidance and Control Software Project Data - Volume 3: Verification Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the verification documents from the GCS project. Volume 3 contains four appendices: A. Software Verification Cases and Procedures for the Guidance and Control Software Project; B. Software Verification Results for the Pluto Implementation of the Guidance and Control Software; C. Review Records for the Pluto Implementation of the Guidance and Control Software; and D. Test Results Logs for the Pluto Implementation of the Guidance and Control Software.

21 CFR 312.145 - Guidance documents.

Science.gov (United States)

2010-04-01

... of Drug Information, Center for Drug Evaluation and Research, Food and Drug Administration, 10903 New... Evaluation and Research, Food and Drug Administration, 1401 Rockville Pike, Rockville, MD 20852-1448. [65 FR... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Guidance documents. 312.145 Section 312.145 Food...

Standard Review Plan Maintenance Program implementing procedures document

International Nuclear Information System (INIS)

1996-11-01

The implementing Procedures Document (IPD) was developed by the Inspection Program Projects Branch, Office of Nuclear Reactor Regulation, with assistance from Pacific Northwest National Laboratory, for the Standard Review Plan Maintenance Program (SRP-MP). The SRP-MP was established to maintain the Standard Review Plan (SRP) on an on-going basis. The IPD provides guidance, including an overall approach and procedures, for SRP-MP tasks. The objective of the IPD is to ensure that modifications to SRP need to reflect current NRC requirements and guidance are identified and that a consistent methodology is used to develop and revise SRP sections

Guidance and Control Software Project Data - Volume 2: Development Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the development documents from the GCS project. Volume 2 contains three appendices: A. Guidance and Control Software Development Specification; B. Design Description for the Pluto Implementation of the Guidance and Control Software; and C. Source Code for the Pluto Implementation of the Guidance and Control Software

Commercial radioactive waste minimization program development guidance

International Nuclear Information System (INIS)

Fischer, D.K.

1991-01-01

This document is one of two prepared by the EG ampersand G Idaho, Inc., Waste Management Technical Support Program Group, National Low-Level Waste Management Program Unit. One of several Department of Energy responsibilities stated in the Amendments Act of 1985 is to provide technical assistance to compact regions Host States, and nonmember States (to the extent provided in appropriations acts) in establishing waste minimization program plans. Technical assistance includes, among other things, the development of technical guidelines for volume reduction options. Pursuant to this defined responsibility, the Department of Energy (through EG ampersand G Idaho, Inc.) has prepared this report, which includes guidance on defining a program, State/compact commission participation, and waste minimization program plans

Hanford site guide for preparing and maintaining generator group pollution prevention program documentation

International Nuclear Information System (INIS)

1995-12-01

This manual provides the necessary guidance to contractor generator groups for developing and maintaining documentation of their pollution prevention (P2) program activities. Preparation of program documentation will demonstrate compliance with contractor and U.S. Department of Energy (DOE) requirements, as well as state and federal regulations. Contractor waste generator groups are no longer required to prepare and update facility waste minimization plans. Developing and maintaining program documentation replace this requirement

Codes and standards and other guidance cited in regulatory documents. Revision 1

International Nuclear Information System (INIS)

Ankrum, A.; Nickolaus, J.; Vinther, R.; Maguire-Moffitt, N.; Hammer, J.; Sherfey, L.; Warner, R.

1994-08-01

As part of the US Nuclear Regulatory Commission (NRC) Standard Review Plan Update and Development Program, Pacific Northwest Laboratory developed a listing of industry consensus codes and standards and other government and industry guidance referred to in regulatory documents. In addition to updating previous information, Revision 1 adds citations from the NRC Inspection Manual and the Improved Standard Technical Specifications. This listing identifies the version of the code or standard cited in the regulatory document, the regulatory document, and the current version of the code or standard. It also provides a summary characterization of the nature of the citation. This listing was developed from electronic searches of the Code of Federal Regulations and the NRC's Bulletins, Information Notices, Circulars, Generic Letters, Policy Statements, Regulatory Guides, and the Standard Review Plan (NUREG-0800)

Codes and standards and other guidance cited in regulatory documents. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Ankrum, A.; Nickolaus, J.; Vinther, R.; Maguire-Moffitt, N.; Hammer, J.; Sherfey, L.; Warner, R. [Pacific Northwest Lab., Richland, WA (United States)

1994-08-01

As part of the US Nuclear Regulatory Commission (NRC) Standard Review Plan Update and Development Program, Pacific Northwest Laboratory developed a listing of industry consensus codes and standards and other government and industry guidance referred to in regulatory documents. In addition to updating previous information, Revision 1 adds citations from the NRC Inspection Manual and the Improved Standard Technical Specifications. This listing identifies the version of the code or standard cited in the regulatory document, the regulatory document, and the current version of the code or standard. It also provides a summary characterization of the nature of the citation. This listing was developed from electronic searches of the Code of Federal Regulations and the NRC`s Bulletins, Information Notices, Circulars, Generic Letters, Policy Statements, Regulatory Guides, and the Standard Review Plan (NUREG-0800).

Equipment design guidance document for flammable gas waste storage tank new equipment

International Nuclear Information System (INIS)

Smet, D.B.

1996-01-01

This document is intended to be used as guidance for design engineers who are involved in design of new equipment slated for use in Flammable Gas Waste Storage Tanks. The purpose of this document is to provide design guidance for all new equipment intended for application into those Hanford storage tanks in which flammable gas controls are required to be addressed as part of the equipment design. These design criteria are to be used as guidance. The design of each specific piece of new equipment shall be required, as a minimum to be reviewed by qualified Unreviewed Safety Question evaluators as an integral part of the final design approval. Further Safety Assessment may be also needed. This guidance is intended to be used in conjunction with the Operating Specifications Documents (OSDs) established for defining work controls in the waste storage tanks. The criteria set forth should be reviewed for applicability if the equipment will be required to operate in locations containing unacceptable concentrations of flammable gas

Air pollution and public health: a guidance document for risk managers.

Science.gov (United States)

Craig, Lorraine; Brook, Jeffrey R; Chiotti, Quentin; Croes, Bart; Gower, Stephanie; Hedley, Anthony; Krewski, Daniel; Krupnick, Alan; Krzyzanowski, Michal; Moran, Michael D; Pennell, William; Samet, Jonathan M; Schneider, Jurgen; Shortreed, John; Williams, Martin

2008-01-01

This guidance document is a reference for air quality policymakers and managers providing state-of-the-art, evidence-based information on key determinants of air quality management decisions. The document reflects the findings of five annual meetings of the NERAM (Network for Environmental Risk Assessment and Management) International Colloquium Series on Air Quality Management (2001-2006), as well as the results of supporting international research. The topics covered in the guidance document reflect critical science and policy aspects of air quality risk management including i) health effects, ii) air quality emissions, measurement and modeling, iii) air quality management interventions, and iv) clean air policy challenges and opportunities.

Guidance and Control Software Project Data - Volume 4: Configuration Management and Quality Assurance Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes configuration management and quality assurance documents from the GCS project. Volume 4 contains six appendices: A. Software Accomplishment Summary for the Guidance and Control Software Project; B. Software Configuration Index for the Guidance and Control Software Project; C. Configuration Management Records for the Guidance and Control Software Project; D. Software Quality Assurance Records for the Guidance and Control Software Project; E. Problem Report for the Pluto Implementation of the Guidance and Control Software Project; and F. Support Documentation Change Reports for the Guidance and Control Software Project.

Standard Review Plan Update and Development Program. Implementing Procedures Document

Energy Technology Data Exchange (ETDEWEB)

1992-05-01

This implementing procedures document (IPD) was prepared for use in implementing tasks under the standard review plan update and development program (SRP-UDP). The IPD provides comprehensive guidance and detailed procedures for SRP-UDP tasks. The IPD is mandatory for contractors performing work for the SRP-UDP. It is guidance for the staff. At the completion of the SRP-UDP, the IPD will be revised (to remove the UDP aspects) and will replace NRR Office Letter No. 800 as long-term maintenance procedures.

Studying Wind Energy/Bird Interactions: A Guidance Document

Energy Technology Data Exchange (ETDEWEB)

Anderson, R. [California Energy Commission (US); Morrison, M. [California State Univ., Sacramento, CA (US); Sinclair, K. [Dept. of Energy/National Renewable Energy Lab. (US); Strickland, D. [WEST, Inc. (US)

1999-12-01

This guidance document is a product of the Avian Subcommittee of the National Wind Coordinating Committee (NWCC). The NWCC was formed to better understand and promote responsible, credible, and comparable avian/wind energy interaction studies. Bird mortality is a concern and wind power is a potential clean and green source of electricity, making study of wind energy/bird interactions essential. This document provides an overview for regulators and stakeholders concerned with wind energy/bird interactions, as well as a more technical discussion of the basic concepts and tools for studying such interactions.

Nuclear Regulatory Commission staff approaches to improving the integration of regulatory guidance documents and prelicensing reviews

International Nuclear Information System (INIS)

Johnson, R.L.

1994-01-01

The Nuclear Regulatory Commission staff is conducting numerous activities to improve the integration of its regulatory guidance documents (i.e., License Application Review Plan (LARP) and open-quotes Format and Content for the License Application for the High-Level Waste repositoryclose quotes (FCRG)) and pre-license application (LA) reviews. Those activities related to the regulatory guidance documents consist of: (1) developing an hierarchy of example evaluation findings for LARP; (2) identifying LARP review plan interfaces; (3) conducting an integration review of LARP review strategies; (4) correlating LARP to the ongoing technical program; and (5) revising the FCRG. Some of the more important strategies the staff is using to improve the integration of pre-LA reviews with the LA review include: (1) use of the draft LARP to guide the staff's pre-LA reviews; (2) focus detailed pre-LA reviews on key technical uncertainties; (3) identify and track concerns with DOE's program; and (4) use results of pre-LA reviews in LA reviews. The purpose of this paper is to describe these ongoing activities and strategies and discuss some of the new work that is planned to be included in LARP Revision 1 and the final FCRG, which are scheduled to be issued in late 1994. These activities reflect both the importance the staff has placed on integration and the staff's approach to improving integration in these areas. The staff anticipates that the results of these activities, when incorporated in the FCRG, LARP, and pre-LA reviews, will improve its guidance for DOE's ongoing site characterization program and LA annotated outline development

Information architecture. Volume 3: Guidance

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-04-01

The purpose of this document, as presented in Volume 1, The Foundations, is to assist the Department of Energy (DOE) in developing and promulgating information architecture guidance. This guidance is aimed at increasing the development of information architecture as a Departmentwide management best practice. This document describes departmental information architecture principles and minimum design characteristics for systems and infrastructures within the DOE Information Architecture Conceptual Model, and establishes a Departmentwide standards-based architecture program. The publication of this document fulfills the commitment to address guiding principles, promote standard architectural practices, and provide technical guidance. This document guides the transition from the baseline or defacto Departmental architecture through approved information management program plans and budgets to the future vision architecture. This document also represents another major step toward establishing a well-organized, logical foundation for the DOE information architecture.

Guidance for implementing an environmental, safety, and health-assurance program. Volume 15. A model plan for line organization environmental, safety, and health-assurance programs

Energy Technology Data Exchange (ETDEWEB)

Ellingson, A.C.; Trauth, C.A. Jr.

1982-01-01

This is 1 of 15 documents designed to illustrate how an Environmental, Safety and Health (ES and H) Assurance Program may be implemented. The generic definition of ES and H Assurance Programs is given in a companion document entitled An Environmental, Safety and Health Assurance Program Standard. This particular document presents a model operational-level ES and H Assurance Program that may be used as a guide by an operational-level organization in developing its own plan. The model presented here reflects the guidance given in the total series of 15 documents.

Draft Updates to the Planning for Natural Disaster Debris Guidance and to Related Documents

Science.gov (United States)

EPA is requesting comment on the draft update of the Planning for Natural Disaster Debris Guidance, along with two other documents. This Guidance is an update of the Planning for Natural Disaster Debris guidance that EPA published in March 2008.

Cost consideration in the clinical guidance documents of physician specialty societies in the United States.

Science.gov (United States)

Schwartz, Jennifer A T; Pearson, Steven D

2013-06-24

Despite increasing concerns regarding the cost of health care, the consideration of costs in the development of clinical guidance documents by physician specialty societies has received little analysis. To evaluate the approach to consideration of cost in publicly available clinical guidance documents and methodological statements produced between 2008 and 2012 by the 30 largest US physician specialty societies. Qualitative document review. Whether costs are considered in clinical guidance development, mechanism of cost consideration, and the way that cost issues were used in support of specific clinical practice recommendations. Methodological statements for clinical guidance documents indicated that 17 of 30 physician societies (57%) explicitly integrated costs, 4 (13%) implicitly considered costs, 3 (10%) intentionally excluded costs, and 6 (20%) made no mention. Of the 17 societies that explicitly integrated costs, 9 (53%) consistently used a formal system in which the strength of recommendation was influenced in part by costs, whereas 8 (47%) were inconsistent in their approach or failed to mention the exact mechanism for considering costs. Among the 138 specific recommendations in these guidance documents that included cost as part of the rationale, the most common form of recommendation (50 [36%]) encouraged the use of a specific medical service because of equal effectiveness and lower cost. Slightly more than half of the largest US physician societies explicitly consider costs in developing their clinical guidance documents; among these, approximately half use an explicit mechanism for integrating costs into the strength of recommendations. Many societies remain vague in their approach. Physician specialty societies should demonstrate greater transparency and rigor in their approach to cost consideration in documents meant to influence care decisions.

Laboratory Biosafety and Biosecurity Risk Assessment Technical Guidance Document

Energy Technology Data Exchange (ETDEWEB)

Astuto-Gribble, Lisa M; Caskey, Susan Adele

2014-07-01

The purpose of this document is threefold: 1) to describe the laboratory bio safety and biosecurity risk assessment process and its conceptual framework; 2) provide detailed guidance and suggested methodologies on how to conduct a risk assessment; and 3) present some practical risk assessment process strategies using realistic laboratory scenarios.

Spent Nuclear Fuel Project document control and Records Management Program Description

International Nuclear Information System (INIS)

MARTIN, B.M.

2000-01-01

The Spent Nuclear Fuel (SNF) Project document control and records management program, as defined within this document, is based on a broad spectrum of regulatory requirements, Department of Energy (DOE) and Project Hanford and SNF Project-specific direction and guidance. The SNF Project Execution Plan, HNF-3552, requires the control of documents and management of records under the auspices of configuration control, conduct of operations, training, quality assurance, work control, records management, data management, engineering and design control, operational readiness review, and project management and turnover. Implementation of the controls, systems, and processes necessary to ensure compliance with applicable requirements is facilitated through plans, directives, and procedures within the Project Hanford Management System (PHMS) and the SNF Project internal technical and administrative procedures systems. The documents cited within this document are those which directly establish or define the SNF Project document control and records management program. There are many peripheral documents that establish requirements and provide direction pertinent to managing specific types of documents that, for the sake of brevity and clarity, are not cited within this document

Standards for School Guidance Programs in Maryland.

Science.gov (United States)

Maryland State Dept. of Education, Baltimore. Div. of Compensatory, Urban, and Supplementary Programs.

This brochure is a checklist to rate school compliance with the standards for school guidance programs in Maryland, which were developed by the Maryland State Department of Education. The first set of standards addresses the philosophy and goals of school guidance programs in Maryland and the extent to which program goals and objectives are…

DEVELOPMENT PERSONALITY/SOCIAL COMPETENCY OF SECONDARY HIGH SCHOOL STUDENTS TROUGH A COMPREHENSIVE GUIDANCE AND COUNSELING PROGRAM

Directory of Open Access Journals (Sweden)

Anwar Sutoyo

2015-10-01

Full Text Available Abstract The goal this research is to find the effectiveness of model guidance and counseling comprehensive program to develop the personality/ social competency of secondary high school students.This research uses method one group pretest and posttest design. In data collecting technique, this research was directly done through interview, documentation and assessment scale.The conclusions of the research are, The model of guidance and counseling comprehensive program that developed is effective to evolving the personality/ social competency of secondary high school students. Therefore it, counselor need to have leadership ability, create an collaboration atmospherebetweenstakeholders, and tecnology information mastered. Keywords: Comprehensive Program; Personality/ Social Competency 

76 FR 1173 - Draft Guidance for Industry on Electronic Source Documentation in Clinical Investigations...

Science.gov (United States)

2011-01-07

... Web page at http://www.fda.gov/RegulatoryInformation/Guidances/default.htm . FDA guidances are issued and updated regularly. We recommend you check the Web site to ensure that you have the most up-to-date... electronic diaries provided by study subjects. When paper source documents are available for review, tracing...

Evaluation Of Career Guidance Program In Vocational High School

Directory of Open Access Journals (Sweden)

Martaningsih Sri Tutur

2018-01-01

This review of career guidance program evaluation is conducted qualitatively through surveys, interviews and leiterature studies to provide an overview of evaluation program and its relevance to the necessity. Understanding the quality, weaknesses, obstacles to service implementation, and potential utilization are expected to improve career guidance effectiveness services in vocational high school. An evaluation on the overall career guidance program, will provide feedback for ongoing improvement. Various evaluation models are available, it needs to be selected about the relevance to the career counseling program characteristics, so that evaluation feedback is more optimal.

Toward Documentation of Program Evolution

DEFF Research Database (Denmark)

Vestdam, Thomas; Nørmark, Kurt

2005-01-01

The documentation of a program often falls behind the evolution of the program source files. When this happens it may be attractive to shift the documentation mode from updating the documentation to documenting the evolution of the program. This paper describes tools that support the documentatio....... It is concluded that our approach can help revitalize older documentation, and that discovery of the fine grained program evolution steps help the programmer in documenting the evolution of the program....

TECHNICAL GUIDANCE DOCUMENT: CONSTRUCTION QUALITY MANAGEMENT FOR REMEDIAL ACTION AND REMEDIAL DESIGN WASTE CONTAINMENT SYSTEMS

Science.gov (United States)

This Technical Guidance Document is intended to augment the numerous construction quality control and construction quality assurance (CQC and CQA) documents that are available far materials associated with waste containment systems developed for Superfund site remediation. In ge...

Analytical laboratory quality assurance guidance in support of EM environmental sampling and analysis activities

International Nuclear Information System (INIS)

1994-05-01

This document introduces QA guidance pertaining to design and implementation of laboratory procedures and processes for collecting DOE Environmental Restoration and Waste Management (EM) ESAA (environmental sampling and analysis activities) data. It addresses several goals: identifying key laboratory issues and program elements to EM HQ and field office managers; providing non-prescriptive guidance; and introducing environmental data collection program elements for EM-263 assessment documents and programs. The guidance describes the implementation of laboratory QA elements within a functional QA program (development of the QA program and data quality objectives are not covered here)

Comparison of the guidance documents in support of EU risk assessments with those for the derivation of EU water quality standards

NARCIS (Netherlands)

Vos JH; Janssen MPM; SEC

2005-01-01

Risks of both new and existing substances and of biocides in Europe are being evaluated using the Technical Guidance Document (TGD). The European Water Framework Directive refers to this document for establishing Environmental Quality Standards (EQSs) for water. Another guidance document for the

The Vicinity of Program Documentation Tools

DEFF Research Database (Denmark)

Nørmark, Kurt

between program development tools.  In the central part of the paper we introduce a mapping of documentation flow between program development tools.  In addition we discuss a set of locally developed tools which is related to program documentation.  The use of test cases as examples in an interface......Program documentation plays a vital role in almost all programming processes.  Program documentation flows between separate tools of a modularized environment, and in between the components of an integrated development environment as well.  In this paper we discuss the flow of program documentation...... documentation tool is a noteworthy and valuable contribution to the documentation flow.  As an additional contribution we identify several circular relationships which illustrate feedback of documentation to the program editor from other tools in the development environment....

Guidance Document on Anaerobic Digester Foaming Prevention and Control Methods (WERF Report INFR1SG10a)

Science.gov (United States)

The development of this anaerobic digester (AD) foaming guidance document is based on the need for a specific detailed methodology that water resource recovery facilities (WRRF) personnel can follow and implement to manage or mitigate AD foam incidents. This guidance manual is th...

Environmental Guidance Program Reference Book: American Indian Religious Freedom Act

Energy Technology Data Exchange (ETDEWEB)

1987-11-01

This Reference Book contains a copy of the American Indian Religious Freedom Act and guidance for DOE compliance with the statute. The document is provided to DOE and contractor staff for informational purposes only and should not be interpreted as legal guidance. Updates that include important new requirements will be provided periodically.

Quality assurance guidance for low-level radioactive waste disposal facility: Final report

International Nuclear Information System (INIS)

Pittiglio, C.L. Jr.

1989-01-01

This document provides guidance to an applicant on meeting the quality control (QC) requirements for a low-level waste (LLW) disposal facility. The QC requirements are the basis for developing of a quality assurance (QA) program and for the guidance provided herein. The criteria are basic to any QA program. The document specifically establishes QA guidance for the design, construction, and operation of those structures, systems, components, as well as, for site characterization activities necessary to meet the performance objectives and to limit exposure to our release of radioactivity. 7 refs

Public Comment Period Open for the Draft Update to the Planning for Natural Disaster Debris Guidance and to Related Documents

Science.gov (United States)

EPA is requesting comment on the draft Planning for Natural Disaster Debris Guidance, and two other documents. The Guidance is an update of the Planning for Natural Disaster Debris guidance that EPA published in March 2008.

10 CFR 420.32 - Program guidance/solicitation.

Science.gov (United States)

2010-01-01

... SEP and the participating programs in the Office of Energy Efficiency and Renewable Energy; and (2... 10 Energy 3 2010-01-01 2010-01-01 false Program guidance/solicitation. 420.32 Section 420.32 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION STATE ENERGY PROGRAM Implementation of Special Projects...

RCRA Programmatic Information Policy and Guidance

Data.gov (United States)

U.S. Environmental Protection Agency — This asset includes program policy and guidance documents that are used by the EPA regions, states, tribes and private parties to implement the hazardous waste...

Guidance for organizing a local radiation protection program in medical care

International Nuclear Information System (INIS)

Sarby, B.; Jorulf, H.

2000-12-01

The following report is intended to be a guidance of how to organize a local radiation protection program and how it can be incorporated into daily medical care. The report is based on knowledge derived from participation and observations from inspections and the experience from hospitals who for a long time have been working in a well documented organisation. The organisation is described in local. The aim with these documents is to achieve a clear distribution of duties and responsibilities between the licence holder and directors concerned. Furthermore, a basic thought is to establish an efficient form of collaboration between the diverse staff categories and to achieve continuity in the embodiment of new laws and regulations. At that it is important to organise 'the local radiation committee' to operate in close collaboration with the dally medical care

Safeguarding critical e-documents implementing a program for securing confidential information assets

CERN Document Server

Smallwood, Robert F

2012-01-01

Practical, step-by-step guidance for corporations, universities and government agencies to protect and secure confidential documents and business records Managers and public officials are looking for technology and information governance solutions to "information leakage" in an understandable, concise format. Safeguarding Critical E-Documents provides a road map for corporations, governments, financial services firms, hospitals, law firms, universities and other organizations to safeguard their internal electronic documents and private communications.Provides practical, step-by-step guidance o

Synthesis of the IRSN report on its analysis of the safety guidance package (DOrS) of the ASTRID reactor project. Safety guidance document for the ASTRID prototype: Referral to the GPR. Opinion related to the safety guidance document of the ASTRID reactor project. ASTRID prototype: Safety guidance document for the ASTRID prototype

International Nuclear Information System (INIS)

Lachaume, Jean-Luc; Niel, Jean-Christophe

2013-01-01

A first document indicates the improvement guidelines for the ASTRID project based on the French experience in the field of sodium-cooled fast neutron reactors, addresses the safety objectives as they are presented for the ASTRID project, discusses how the project includes a regulation and design referential, and how it addresses various aspects of the design approach (ranking and analysis of operation situations, defence in depth, use of probabilistic studies, safety classification and qualification to accidental situations, taking internal and external aggressions into account and taking severe accidents into account at the design level). It comments the guidelines related to the first two barriers, to main safety functions (control of reactivity and of reactor cooling, containment of radioactive and toxic materials), to dismantling, to R and D for safety support. A second document is a letter sent by the ASN to the GPR (permanent group of experts in charge of nuclear reactors) about the safety guidance document for the ASTRID prototype. The third document is the answer and contains comments and recommendations by this group about the content of this document, and therefore addresses the same topics as the first document. The last document defines the framework of the approach to this document

Hanford Site Guide for Preparing and Maintaining Generator Group Pollution Prevention Documentation

International Nuclear Information System (INIS)

PLACE, B.G.

2000-01-01

This document provides guidance to generator groups for preparing and maintaining documentation of Pollution Prevention/Waste Minimization (P2/WMin) Program activities. The guidance is one of a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan (DOE-RL, 2000) and Prime Contractor implementation plans describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and 3005(h) (RCRA and EPA, 1994) and Department of Energy Acquisition Regulations (DEAR) (48 CFR 970.5204-2 and 48 CFR 970.5204-78). Documentation guidance for the following five P2/WMin elements is discussed: Fiscal Year (FY) Goals; Budget and Staffing; Pollution Prevention (P2) Reporting; WMin Certification; and Waste Minimization (WMin) Assessments (WMAs)

Dissecting Attending Surgeons' Operating Room Guidance: Factors That Affect Guidance Decision Making.

Science.gov (United States)

Chen, Xiaodong Phoenix; Williams, Reed G; Smink, Douglas S

2015-01-01

The amount of guidance provided by the attending surgeon in the operating room (OR) is a key element in developing residents' autonomy. The purpose of this study is to explore factors that affect attending surgeons' decision making regarding OR guidance provided to the resident. We used video-stimulated recall interviews (VSRI) throughout this 2-phase study. In Phase 1, 3 attending surgeons were invited to review separately 30 to 45 minute video segments of their prerecorded surgical operations to explore factors that influenced their OR guidance decision making. In Phase 2, 3 attending surgeons were observed and documented in the OR (4 operations, 341min). Each operating surgeon reviewed their videotaped surgical performance within 5 days of the operation to reflect on factors that affected their decision making during the targeted guidance events. All VSRI were recorded. Thematic analysis and manual coding were used to synthesize and analyze data from VSRI transcripts, OR observation documents, and field notes. A total of 255 minutes of VSRI involving 6 surgeons and 7 surgical operations from 5 different procedures were conducted. A total of 13 guidance decision-making influence factors from 4 categories were identified (Cohen's κ = 0.674): Setting (case schedule and patient morbidity), content (procedure attributes and case progress), resident (current competency level, trustworthiness, self-confidence, and personal traits), and attending surgeon (level of experience, level of comfort, preferred surgical technique, OR training philosophy, and responsibility as surgeon). A total of 5 factors (case schedule, patient morbidity, procedure attributes, resident current competency level, and trustworthiness) influenced attending surgeons' pre-OR guidance plans. "OR training philosophy" and "responsibility as surgeon" were anchor factors that affected attending surgeons' OR guidance decision-making patterns. Surgeons' OR guidance decision making is a dynamic process

Development of a treatability variance guidance document for US DOE mixed-waste streams

International Nuclear Information System (INIS)

Scheuer, N.; Spikula, R.; Harms, T.

1990-03-01

In response to the US Department of Energy's (DOE's) anticipated need for variances from the Resource Conservation and Recovery Act (RCRA) Land Disposal Restrictions (LDRs), a treatability variance guidance document was prepared. The guidance manual is for use by DOE facilities and operations offices. The manual was prepared as a part of an ongoing effort by DOE-EH to provide guidance for the operations offices and facilities to comply with the RCRA (LDRs). A treatability variance is an alternative treatment standard granted by EPA for a restricted waste. Such a variance is not an exemption from the requirements of the LDRs, but rather is an alternative treatment standard that must be met before land disposal. The manual, Guidance For Obtaining Variance From the Treatment Standards of the RCRA Land Disposal Restrictions (1), leads the reader through the process of evaluating whether a variance from the treatment standard is a viable approach and through the data-gathering and data-evaluation processes required to develop a petition requesting a variance. The DOE review and coordination process is also described and model language for use in petitions for DOE radioactive mixed waste (RMW) is provided. The guidance manual focuses on RMW streams, however the manual also is applicable to nonmixed, hazardous waste streams. 4 refs

78 FR 67442 - Congestion Mitigation and Air Quality Improvement Program Interim Guidance

Science.gov (United States)

2013-11-12

...] Congestion Mitigation and Air Quality Improvement Program Interim Guidance AGENCY: Federal Highway... Comment. SUMMARY: The FHWA is issuing Interim Guidance on the Congestion Mitigation and Air Quality.../environment/air_quality/cmaq/policy_and_guidance/2008_guidance/ guidance/. DATES: This Interim Guidance is...

Guidance for implementing an environmental, safety, and health assurance program. Volume 10. Model guidlines for line organization environmental, safety and health audits and appraisals

International Nuclear Information System (INIS)

Ellingson, A.C.

1981-10-01

This is 1 of 15 documents designed to illustrate how an Environmental, Safety and Health (ES and H) Assurance Program may be implemented. The generic definition of ES and H Assurance Programs is given in a companion document entitled An Environmental, Safety and Health Assurance Program Standard. The Standard specifies that the operational level of an institution must have an internal assurance function, and this document provides guidance for the audit/appraisal portion of the operational level's ES and H program. The appendixes include an ES and H audit checklist, a sample element rating guide, and a sample audit plan for working level line organization internal audits

Precise documentation of well-structured programs

Energy Technology Data Exchange (ETDEWEB)

Parnas, D.L.; Madey, J.; Iglewski, M. [McMaster Univ., Hamilton, Ontario (Canada)

1997-11-01

This paper describes a new form of program documentation that is precise, systematic and readable. This documentation comprises a set of displays supplemented by a lexicon and an index. Each display presents a program fragment in such a way that its correctness can be examined without looking at any other display. Each display has three parts: (1) the specification of the program presented in the display, (2) the program itself, and (3) the specifications of programs invoked by this program. The displays are intended to be used by Software Engineers as a reference document during inspection and maintenance. This paper also introduces a specification technique that is a refinement of Mills functional approach to program documentation and verification; programs are specified and described in tabular form.

Guidance for implementing the UMTRA Project long-term surveillance program

International Nuclear Information System (INIS)

1992-09-01

The US Nuclear Regulatory Commission (NRC) has issued a general license for the custody and long-term care of US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project permanent disposal sites. The purpose of this general license is to ensure that the UMTRA disposal sites will be cared for in such a manner as to protect the public health and safety and the environment upon completion of remedial actions. The general license will be in effect for a disposal site when NRC accepts the disposal site long-term surveillance plan (LTSP) that meets the requirements of 10 CFR 40.27. The site LTSP describes in detail the long-term surveillance program, including any monitoring, maintenance, and emergency measures necessary to fulfill the conditions of the general license. This guidance document provides (1) instructions for preparing the disposal site LTSPs and (2) instructions for carrying out the UMTRA Project long-term surveillance program, including any monitoring that may be required. The information provided in this document also is in accordance with the regulatory requirements set forth in 40 CFR 192. On January 5, 1985, the US Tenth Circuit Court of Appeals remanded the groundwater standards, 40 CFR 192.02. Proposed groundwater standards were issued for comment on September 24, 1987 (52 FR 3600). When the groundwater standards become final, this document will be revised, as appropriate. This document also will be updated in response to any changes to 10 CFR 40, or in response to changes in the manner in which the long-term care of the licensed disposal sites is carried out

European Society of Clinical Microbiology and Infectious Diseases: update of the treatment guidance document for Clostridium difficile infection

NARCIS (Netherlands)

Debast, S.B.; Bauer, M.P.; Kuijper, E.J.; et al.,

2014-01-01

In 2009 the first European Society of Clinical Microbiology and Infection (ESCMID) treatment guidance document for Clostridium difficile infection (CDI) was published. The guideline has been applied widely in clinical practice. In this document an update and review on the comparative effectiveness

Long-Term Stewardship Baseline Report and Transition Guidance

Energy Technology Data Exchange (ETDEWEB)

Kristofferson, Keith

2001-11-01

Long-term stewardship consists of those actions necessary to maintain and demonstrate continued protection of human health and the environment after facility cleanup is complete. As the Department of Energy’s (DOE) lead laboratory for environmental management programs, the Idaho National Engineering and Environmental Laboratory (INEEL) administers DOE’s long-term stewardship science and technology efforts. The INEEL provides DOE with technical, and scientific expertise needed to oversee its long-term environmental management obligations complexwide. Long-term stewardship is administered and overseen by the Environmental Management Office of Science and Technology. The INEEL Long-Term Stewardship Program is currently developing the management structures and plans to complete INEEL-specific, long-term stewardship obligations. This guidance document (1) assists in ensuring that the program leads transition planning for the INEEL with respect to facility and site areas and (2) describes the classes and types of criteria and data required to initiate transition for areas and sites where the facility mission has ended and cleanup is complete. Additionally, this document summarizes current information on INEEL facilities, structures, and release sites likely to enter long-term stewardship at the completion of DOE’s cleanup mission. This document is not intended to function as a discrete checklist or local procedure to determine readiness to transition. It is an overarching document meant as guidance in implementing specific transition procedures. Several documents formed the foundation upon which this guidance was developed. Principal among these documents was the Long-Term Stewardship Draft Technical Baseline; A Report to Congress on Long-Term Stewardship, Volumes I and II; Infrastructure Long-Range Plan; Comprehensive Facility Land Use Plan; INEEL End-State Plan; and INEEL Institutional Plan.

Instruction in Documentation for Computer Programming

Science.gov (United States)

Westley, John W.

1976-01-01

In addition to the input/output record format, the program flowchart, the program listing, and the program test output, eight documentation items are suggested in order that they may serve as a base from which to start teaching program documentation. (Author/AG)

Quality assurance guidance for a low-level radioactive waste disposal facility

International Nuclear Information System (INIS)

Pittiglio, C.L. Jr.; Hedges, D.

1991-04-01

This document provides guidance to an applicant on meeting the quality control (QC) requirements of 10 CFR 61.12(j) for a low-level radioactive waste (LLRW) disposal facility. The QC requirements, plus audits and managerial controls requirements, establish the need for developing a quality assurance (QA) program and the guidance provided herein. The criteria developed for this document are similar to the criteria developed for Appendix B to Title 10 of the Code of Federal Regulations (10 CFR) Part 50. Although Appendix B is not a regulatory requirement for an LLRW disposal facility, the criteria that were developed for 10 CFR Part 50 are basic to any QA program. This document establishes QA guidance for the design, construction, and operation of those structures, engineered or natural systems, and components whose function is required to meet the performance objectives of Subpart C of 10 CFR Part 61 and to limit exposure to or release of radioactivity. 7 refs

Environmental guidance for public participation in environmental restoration activities

Energy Technology Data Exchange (ETDEWEB)

1991-11-01

The US Department of Energy (DOE) is issuing this document, entitled Guidance on Public Participation for US Department of Energy Environmental Restoration Activities, to summarize policy and provide guidance for public participation in environmental restoration activities at DOE Headquarters, Field Offices, facilities, and laboratories. While the Office of Environmental Restoration and Waste Management (EM) has environmental restoration responsibility for the majority of DOE sites and facilities, other DOE Project Offices have similar responsibilities at their sites and facilities. This guidance is applicable to all environment restoration activities conducted by or for DOE under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) as amended by the Superfund Amendments and Reauthorization Act of 1986 (SARA); the Resource Conservation and Recovery Act of 1976 (RCRA) as amended by the Hazardous and Solid Waste Amendments of 1984 (HSWA) (corrective actions only); and the National Environmental Policy Act of 1969 (NEPA). This guidance also is applicable to CERCLA remedial action programs under the Uranium Mill Tailings Radiation Control Act of 1978 and the Formerly Utilized Sites Remedial Action Program, where DOE is the designated lead. The primary objectives of this guidance document are as follows: acclimate DOE staff to a changing culture that emphasizes the importance of public participation activities; provide direction on implementing these public participation activities; and, provide consistent guidance for all DOE Field Offices and facilities. The purpose of this document is to provide guidance on conducting effective public participation activities for environmental restoration activities under CERCLA; RCRA corrective actions under sections 3004(u), 3004(v), and 3008(h); and NEPA public participation activities.

National Environmental Policy Act guidance: A model process

International Nuclear Information System (INIS)

Angle, B.M.; Lockhart, V.A.T.; Sema, B.; Tuott, L.C.; Irving, J.S.

1995-04-01

The ''Model National Environmental Policy Act (NEPA) Process'' includes: References to regulations, guidance documents, and plans; training programs; procedures; and computer databases. Legislative Acts and reference documents from Congress, US Department of Energy, and Lockheed Idaho Technologies Company provide the bases for conducting NEPA at the Idaho National Engineering Laboratory (INEL). Lockheed Idaho Technologies Company (LITCO) NEPA / Permitting Department, the Contractor Environmental Organization (CEO) is responsible for developing and maintaining LITCO NEPA and permitting policies, guidance, and procedures. The CEO develops procedures to conduct environmental evaluations based on NEPA, Council on Environmental Quality (CEQ) regulations, and DOE guidance. This procedure includes preparation or support of environmental checklists, categorical exclusion determinations, environmental assessment determinations, environmental assessments, and environmental impact statements. In addition, the CEO uses this information to train personnel conducting environmental evaluations at the INEL. Streamlining these procedures fosters efficient use of resources, quality documents, and better decisions on proposed actions

Guidance for Facilities on Risk Management Programs (RMP)

Science.gov (United States)

Includes supplemental guidance specific to ammonia refrigeration, wastewater treatment, propane storage, warehouses, chemical distributors, offsite consequence analysis, retail agriculture, applicability of program levels, prevention, emergency response.

EFSA Guidance Document on the risk assessment of plant protection products on bees (Apis mellifera, Bombus spp. and solitary bees)

NARCIS (Netherlands)

Arnold, G.; Boesten, J.J.T.I.; Clook, M.

2013-01-01

The Guidance Document is intended to provide guidance for notifiers and authorities in the context of the review of plant protection products (PPPs) and their active substances under Regulation (EC) 1107/2009. The scientific opinion on the science behind the development of a risk assessment of plant

MGR COMPLIANCE PROGRAM GUIDANCE PACKAGE FOR RADIATION PROTECTION EQUIPMENT, INSTRUMENTATION, AND FACILITIES

International Nuclear Information System (INIS)

2000-01-01

This Compliance Program Guidance Package identifies the regulatory guidance and industry codes and standards addressing radiation protection equipment, instrumentation, and support facilities considered to be appropriate for radiation protection at the Monitored Geologic Repository (MGR). Included are considerations relevant to radiation monitoring instruments, calibration, contamination control and decontamination, respiratory protection equipment, and general radiation protection facilities. The scope of this Guidance Package does not include design guidance relevant to criticality monitoring, area radiation monitoring, effluent monitoring, and airborne radioactivity monitoring systems since they are considered to be the topics of specific design and construction requirements (i.e., ''fixed'' or ''built-in'' systems). This Guidance Package does not address radiation protection design issues; it addresses the selection and calibration of radiation monitoring instrumentation to the extent that the guidance is relevant to the operational radiation protection program. Radon and radon progeny monitoring instrumentation is not included in the Guidance Package since such naturally occurring radioactive materials do not fall within the NRC's jurisdiction at the MGR

76 FR 9381 - Notice of Availability of Interim Staff Guidance Documents for Spent Fuel Storage Casks

Science.gov (United States)

2011-02-17

.... FOR FURTHER INFORMATION CONTACT: Matthew Gordon, Structural Mechanics and Materials Branch, Division... transportation packaging licensing actions.'' This ISG document would provide guidance to the NRC staff when... a fee. Comments and questions on ISG-23 should be directed to Matthew Gordon, Structural Mechanics...

Cycle water chemistry based on film forming amines at power plants: evaluation of technical guidance documents

Science.gov (United States)

Dyachenko, F. V.; Petrova, T. I.

2017-11-01

Efficiency and reliability of the equipment in fossil power plants as well as in combined cycle power plants depend on the corrosion processes and deposit formation in steam/water circuit. In order to decrease these processes different water chemistries are used. Today the great attention is being attracted to the application of film forming amines and film forming amine products. The International Association for the Properties of Water and Steam (IAPWS) consolidated the information from all over the World, and based on the research studies and operating experience of researchers and engineers from 21 countries, developed and authorized the Technical Guidance Document: “Application of Film Forming Amines in Fossil, Combined Cycle, and Biomass Power Plants” in 2016. This article describe Russian and International technical guidance documents for the cycle water chemistries based on film forming amines at fossil and combined cycle power plants.

Guidance Document - Full-cost Recovery for Molybdenum-99 Irradiation Services: Methodology and Implementation

International Nuclear Information System (INIS)

Westmacott, Chad; Cameron, Ron

2012-02-01

At the request of its member countries, the OECD Nuclear Energy Agency (NEA) became involved in global efforts to ensure a reliable supply of molybdenum-99 ( 99 Mo) and its decay product, technetium-99m (' 99m Tc), the most widely used medical radioisotope. The NEA established the High-level Group on the Security of Supply of Medical Radioisotopes (HLG-MR) in 2009. Under its first mandate (June 2009-2011), the HLG-MR examined the major issues that affect the short-, medium- and long-term reliability of 99 Mo/' 99m Tc supply and then developed a policy approach to move the supply chain to a sustainable basis and ensure security of supply. The objectives of the HLG-MR during its second mandate (July 2011-2013) are to work towards increasing the long-term security of supply of 99 Mo and ' 99m Tc, especially through the implementation of the HLG-MR policy approach and its associated recommendations. This will entail actions to maintain transparency on global developments, continue communication with the supply chain and end users, evaluate progress toward implementation and provide additional information and analysis where necessary. A key action under the second mandate is to provide guidance on the implementation of the HLG-MR policy approach. This document provides guidance to reactor and alternative production technology (e.g., cyclotrons, accelerators) operators on how to undertake full-cost identification and implement full-cost recovery. The document also discusses issues related to levelling the playing field between old and new reactors. In order to move toward a long-term secure supply of 99 Mo and ' 99m Tc, the HLG-MR policy approach will need to be implemented by all countries that have an impact on the global market - as producers or consumers. A key recommendation of the policy approach is the implementation of full-cost identification and recovery by operators of 99 Mo-producing research reactors or alternative technologies. This document provides the

78 FR 48175 - Retrospective Review of Draft Guidance Documents Issued Before 2010; Withdrawal of Guidances

Science.gov (United States)

2013-08-07

... guidances (number 19 through 22), contact the Office of Pharmaceutical Science in CDER. 23. ``Qualifying for... to the pharmaceutical industry. In most cases, FDA has developed other guidances and resources to... guidances: 1. ``Manufacturing, Processing, or Holding Active Pharmaceutical Ingredients''--issued April 1998...

34 CFR 403.161 - How must funds be used under the Comprehensive Career Guidance and Counseling Programs?

Science.gov (United States)

2010-07-01

... Guidance and Counseling Programs? 403.161 Section 403.161 Education Regulations of the Offices of the... the Special Programs? Comprehensive Career Guidance and Counseling Programs § 403.161 How must funds be used under the Comprehensive Career Guidance and Counseling Programs? (a) A State shall use not...

Repository-based software engineering program: Concept document

Science.gov (United States)

1992-01-01

This document provides the context for Repository-Based Software Engineering's (RBSE's) evolving functional and operational product requirements, and it is the parent document for development of detailed technical and management plans. When furnished, requirements documents will serve as the governing RBSE product specification. The RBSE Program Management Plan will define resources, schedules, and technical and organizational approaches to fulfilling the goals and objectives of this concept. The purpose of this document is to provide a concise overview of RBSE, describe the rationale for the RBSE Program, and define a clear, common vision for RBSE team members and customers. The document also provides the foundation for developing RBSE user and system requirements and a corresponding Program Management Plan. The concept is used to express the program mission to RBSE users and managers and to provide an exhibit for community review.

Guidance for establishment and implementation of field sample management programs in support of EM environmental sampling and analysis activities

International Nuclear Information System (INIS)

1994-01-01

The role of the National Sample Management Program (NSMP) proposed by the Department of Energy's Office of Environmental Management (EM) is to be a resource for EM programs and for local Field Sample Management Programs (FSMPs). It will be a source of information on sample analysis and data collection within the DOE complex. The purpose of this document is to establish the suggested scope of the FSMP activities to be performed under each Operations Office, list the drivers under which the program will operate, define terms and list references. This guidance will apply only to EM sampling and analysis activities associated with project planning, contracting, laboratory selection, sample collection, sample transportation, laboratory analysis and data management

Defense Transuranic Waste Program Strategy Document

International Nuclear Information System (INIS)

1984-01-01

The Defense Transuranic Waste Program (DTWP) Strategy Document presents the general strategy for managing transuranic (TRU) waste materials generated during defense and research activities regulated by the US Department of Energy. The Strategy Document includes discussion of objectives and activities relating to the entire Defense Transuranic Waste Program. However, the primary focus is on the specific management responsibilities of the Transuranic Waste Lead Organization (TLO). The document also includes an updated summary of progress on TLO-managed activities over the past year

A review of Grey and academic literature of evaluation guidance relevant to public health interventions.

Science.gov (United States)

Denford, Sarah; Abraham, Charles; Callaghan, Margaret; Aighton, Peter; De Vocht, Frank; Arris, Steven

2017-09-12

Public Health evaluation is essential to understanding what does and does not work, and robust demonstration of effectiveness may be crucial to securing future funding. Despite this, programs are often implemented with poor, incomplete or no evaluation. Public health practitioners are frequently required to provide evidence for the effectiveness of their services; thus, there is a growing need for evaluation guidance on how to evaluate public health programs. The aim of this study is to identify accessible high-quality, evaluation guidance, available to researchers and practitioners and to catalogue, summarise and categorise the content of a subset of accessible, quality guides to evaluation. We systematically reviewed grey and academic literature for documents providing support for evaluation of complex health interventions. Searches were conducted January to March 2015, and included academic databases, internet search engines, and consultations with academic and practicing public health experts. Data were extracted by two authors and sent to the authors of the guidance documents for comments. Our initial search identified 402 unique documents that were screened to identify those that were (1) developed by or for a national or international organization (2) freely available to all (3) published during or after 2000 (4) specific to public health. This yielded 98 documents from 43 organisations. Of these, 48 were reviewed in detail. This generated a detailed catalogue of quality evaluation guidance. The content included in documents covers 37 facets of evaluation. A wide range of guidance on evaluation of public health initiatives is available. Time and knowledge constraints may mean that busy practitioners find it challenging to access the most, up-to-date, relevant and useful guidance. This review presents links to and reviews of 48 quality guides to evaluation as well as categorising their content. This facilitates quick and each access to multiple selected

Identification of technical guidance related to ground water monitoring

Energy Technology Data Exchange (ETDEWEB)

Vogelsberger, R.R.; Smith, E.D.; Broz, M.; Wright, J.C. Jr.

1987-05-01

Monitoring of ground water quality is a key element of ground water protection and is mandated by several federal and state laws concerned with water quality or waste management. Numerous regulatory guidance documents and technical reports discuss various aspects of ground water monitoring, but at present there is no single source of guidance on procedures and practices for ground water monitoring. This report is intended to assist US Department of Energy (DOE) officials and facility operating personnel in identifying sources of guidance for developing and implementing ground water monitoring programs that are technically sound and that comply with applicable regulations. Federal statutes and associated regulations were reviewed to identify requirements related to ground water monitoring, and over 160 documents on topics related to ground water monitoring were evaluated for their technical merit, their utility as guidance for regulatory compliance, and their relevance to DOE's needs. For each of 15 technical topics involved in ground water monitoring, the report presents (1) a review of federal regulatory requirements and representative state requirements, (2) brief descriptions of the contents and merits of available guidance documents and technical references, and (3) recommendations of the guidance documents or other technical resources that appear to be most appropriate for use in DOE's monitoring activities. The contents of the report are applicable to monitoring activities involving both radioactive and nonradioactive substances. The main sources of regulatory requirements considered in the report are the Atomic Energy Act (including the Uranium Mill Tailings Radiation Control Act), Resource Conservation and Recovery Act, Comprehensive Environmental Response, Compensation and Liability Act, Safe Drinking Water Act, Toxic Substances Control Act, and Federal Water Pollution Control Act.

Identification of technical guidance related to ground water monitoring

International Nuclear Information System (INIS)

Vogelsberger, R.R.; Smith, E.D.; Broz, M.; Wright, J.C. Jr.

1987-05-01

Monitoring of ground water quality is a key element of ground water protection and is mandated by several federal and state laws concerned with water quality or waste management. Numerous regulatory guidance documents and technical reports discuss various aspects of ground water monitoring, but at present there is no single source of guidance on procedures and practices for ground water monitoring. This report is intended to assist US Department of Energy (DOE) officials and facility operating personnel in identifying sources of guidance for developing and implementing ground water monitoring programs that are technically sound and that comply with applicable regulations. Federal statutes and associated regulations were reviewed to identify requirements related to ground water monitoring, and over 160 documents on topics related to ground water monitoring were evaluated for their technical merit, their utility as guidance for regulatory compliance, and their relevance to DOE's needs. For each of 15 technical topics involved in ground water monitoring, the report presents (1) a review of federal regulatory requirements and representative state requirements, (2) brief descriptions of the contents and merits of available guidance documents and technical references, and (3) recommendations of the guidance documents or other technical resources that appear to be most appropriate for use in DOE's monitoring activities. The contents of the report are applicable to monitoring activities involving both radioactive and nonradioactive substances. The main sources of regulatory requirements considered in the report are the Atomic Energy Act (including the Uranium Mill Tailings Radiation Control Act), Resource Conservation and Recovery Act, Comprehensive Environmental Response, Compensation and Liability Act, Safe Drinking Water Act, Toxic Substances Control Act, and Federal Water Pollution Control Act

Quality assurance application in the documentation of nuclear research reactor

International Nuclear Information System (INIS)

Nababan, N.

1999-01-01

For each nuclear research reactor a document control system should be established and should be provide for preparation, review, approval, issuance, distribution, revision and validation (where appropriate) of documents essential to the management, performance and verification of work. In the document control system the responsibilities for each participating organization or individual should be defined in writing. The types of document include, but are not limited to document comprising the QA program, safety requirements, maintenance and operating procedures, inspection instructions, inspection and test reports, assessment reports, drawings, data files, calculations, specifications, computer codes, purchase orders and related documents, vendor supplied documents and work instruction. Management should identify the need for documents and should provide guidance to the organizations and people preparing them. The guidance should cover the status, scope and contents and the policies, standards and codes witch apply. It should also explain the need for feedback of experience. Plant modification or the results of assessments could also give rise to the need for a new document

76 FR 44594 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2011-07-26

... Dockets Management (see ADDRESSES) either electronic or written comments regarding this document. It is... Stimulation Systems.'' This guidance document describes a means by which a repetitive transcranial magnetic... guidance document is being immediately implemented as the special control for rTMS systems, but it remains...

Quality assurance and quality control in mammography: a review of available guidance worldwide.

Science.gov (United States)

Reis, Cláudia; Pascoal, Ana; Sakellaris, Taxiarchis; Koutalonis, Manthos

2013-10-01

Review available guidance for quality assurance (QA) in mammography and discuss its contribution to harmonise practices worldwide. Literature search was performed on different sources to identify guidance documents for QA in mammography available worldwide in international bodies, healthcare providers, professional/scientific associations. The guidance documents identified were reviewed and a selection was compared for type of guidance (clinical/technical), technology and proposed QA methodologies focusing on dose and image quality (IQ) performance assessment. Fourteen protocols (targeted at conventional and digital mammography) were reviewed. All included recommendations for testing acquisition, processing and display systems associated with mammographic equipment. All guidance reviewed highlighted the importance of dose assessment and testing the Automatic Exposure Control (AEC) system. Recommended tests for assessment of IQ showed variations in the proposed methodologies. Recommended testing focused on assessment of low-contrast detection, spatial resolution and noise. QC of image display is recommended following the American Association of Physicists in Medicine guidelines. The existing QA guidance for mammography is derived from key documents (American College of Radiology and European Union guidelines) and proposes similar tests despite the variations in detail and methodologies. Studies reported on QA data should provide detail on experimental technique to allow robust data comparison. Countries aiming to implement a mammography/QA program may select/prioritise the tests depending on available technology and resources. •An effective QA program should be practical to implement in a clinical setting. •QA should address the various stages of the imaging chain: acquisition, processing and display. •AEC system QC testing is simple to implement and provides information on equipment performance.

Quality assurance guidance for laboratory assessment plates in support of EM environmental sampling and analysis activities

International Nuclear Information System (INIS)

1994-05-01

This document is one of several guidance documents developed to support the EM (DOE Environmental Restoration and Waste Management) Analytical Services program. Its purpose is to introduce assessment plates that can be used to conduct performance assessments of an organization's or project's ability to meet quality goals for analytical laboratory activities. These assessment plates are provided as non-prescriptive guidance to EM-support organizations responsible for collection of environmental data for remediation and waste management programs at DOE facilities. The assessments evaluate objectively all components of the analytical laboratory process to determine their proper selection and use

Offshore Wind Guidance Document: Oceanography and Sediment Stability (Version 1) Development of a Conceptual Site Model.

Energy Technology Data Exchange (ETDEWEB)

Roberts, Jesse D.; Jason Magalen; Craig Jones

2014-06-01

This guidance document provide s the reader with an overview of the key environmental considerations for a typical offshore wind coastal location and the tools to help guide the reader through a thoro ugh planning process. It will enable readers to identify the key coastal processes relevant to their offshore wind site and perform pertinent analysis to guide siting and layout design, with the goal of minimizing costs associated with planning, permitting , and long - ter m maintenance. The document highlight s site characterization and assessment techniques for evaluating spatial patterns of sediment dynamics in the vicinity of a wind farm under typical, extreme, and storm conditions. Finally, the document des cribe s the assimilation of all of this information into the conceptual site model (CSM) to aid the decision - making processes.

Analysis of Guidance and Counseling Program at Thika High School for the Blind, Kenya

Science.gov (United States)

Irungu, Mary Wangari; Wamocho, Franciscah Irangi

2010-01-01

The purpose of this study was to analyze the guidance and counseling program at Thika High School for the Blind, the only residential secondary school for students with visual impairments in Kenya. The study examined the content of the existing guidance and counseling program and whether the teacher counselors were adequately trained to handle the…

BASIC Instructional Program: System Documentation.

Science.gov (United States)

Dageforde, Mary L.

This report documents the BASIC Instructional Program (BIP), a "hands-on laboratory" that teaches elementary programming in the BASIC language, as implemented in the MAINSAIL language, a machine-independent revision of SAIL which should facilitate implementation of BIP on other computing systems. Eight instructional modules which make up…

Interim Consequence Management Guidance for a Wide-Area Biological Attack

Energy Technology Data Exchange (ETDEWEB)

Raber, Ellen [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kirvel, Robert [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); MacQueen, Don [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Love, Adam [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Dombroski, Matthew [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); McGrann, Thomas [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Richards, John [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Melius, Carl [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bunt, Thomas [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hibbard, Wilthea [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Greenwalt, Robert [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Miles, Robin [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Dillon, Michael [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mancieri, Sav [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Harris, Steve [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Michalik, Richard [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wheeler, Richard [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hoppes, Bill [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Tucker, Mark [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Krauter, Paula [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Knowlton, Robert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Yang, Lynn [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Franco, Dave [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Einfeld, Wayne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Brockman, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Betty, Rita [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2011-05-17

The Interagency Biological Restoration Demonstration (IBRD) program is a collaborative, interagency effort co-chaired by the Department of Homeland Security and Department of Defense aimed at improving the nation‘s ability to respond to and recover from a large-scale, wide-area, domestic attack involving the release of an environmentally persistent biological warfare agent. The program is focused on understanding interactions between the civilian and military sectors, and in building mutual support to carry out such remediations. This Interim Consequence Management Guidance document provides guidance for decisionmakers in executing activities required to respond to and recover from a biological incident affecting a wide urban area insofar as information is currently available. The spore-forming bacterium Bacillus anthracis is discussed as the biological agent of primary concern because it is the most difficult of known bioterrorism agents to inactivate and is considered to be one of the key threat agents. Most other biological threat agents are much easier to remediate, and in many cases, inactivation would occur naturally within days as a result of environmental exposure; however, the framework and operational questions that need to be addressed are expected to remain the same. The guidance in this document is applicable to (1) enclosed facilities, such as commercial, residential, and continental U.S. military facilities; (2) semi-enclosed facilities, such as subways and public transit facilities; (3) outdoor areas (both localized and wide area), such as building exteriors, streets, parks, and other open spaces; (4) drinking water facilities; and (5) drinking water sources. This document follows an interagency framework [Planning Guidance for Recovery Following Biological Incidents (DHS and EPA 2009)]—which considered Raber et al. (2002) in its development—but takes the framework to a more operational level and provides guidance at key action and decision

Apollo experience report: Guidance and control systems. Engineering simulation program

Science.gov (United States)

Gilbert, D. W.

1973-01-01

The Apollo Program experience from early 1962 to July 1969 with respect to the engineering-simulation support and the problems encountered is summarized in this report. Engineering simulation in support of the Apollo guidance and control system is discussed in terms of design analysis and verification, certification of hardware in closed-loop operation, verification of hardware/software compatibility, and verification of both software and procedures for each mission. The magnitude, time, and cost of the engineering simulations are described with respect to hardware availability, NASA and contractor facilities (for verification of the command module, the lunar module, and the primary guidance, navigation, and control system), and scheduling and planning considerations. Recommendations are made regarding implementation of similar, large-scale simulations for future programs.

Evaluation of the endocrine activity of 2,4,6-tribromophenol, benzanthrone and benzophenone-2 based on Appendix 7.8-5 of REACH guidance document

DEFF Research Database (Denmark)

Duis, Karen; Holbech, Henrik; Velasco-Santamaría, Yohana M.

Within a project funded by the German Federal Environment Agency, the practicability of Appendix 7.8-5 of REACH guidance document R.7b was evaluated using three case study substances. Shortcomings in the guidance were identified. An assessment of potential endocrine activity in aquatic vertebrates...

Development of guidance and methodical documents for providing the decommissioning of radiation-hazardous objects

International Nuclear Information System (INIS)

Ermakov, A.

2015-01-01

Federal Center for Nuclear and Radiation Safety (JSC FCNRS) developed and approbated guidance and methodical documents for providing the facility to radiologically safe status in the course of Building B decommissioning activity at JSC VNIINM (A.A. Bochvar High-Technology Scientific Research Institute for Inorganic Materials). The scope of application of the documents developed is as follows: - preliminary segregation of radwaste into streams during its collection and preparation for removal from facilities/sites under decommissioning; - express assessment of specific activity (activity) of radwaste generated in the course of dismantling and decontamination activities; - radiological survey of premises and building structures following completion of dismantling and decontamination activities; - SRW processing (compaction, reduction in size), packaging, characterisation and containerisation in order to reduce risks of spread of radioactive contamination. Documents that have been developed can be used both at nuclear facilities/ sites similar to the JSC VNIINM Building B in terms of work stages and types of waste to be generated, and other facilities/ sites taking into consideration their peculiarities. (author)

Safety guidance and inspection program for particle accelerator

Energy Technology Data Exchange (ETDEWEB)

Lee, Do Whey [Korea Institute of Nuclear Safety, Taejon (Korea, Republic of); Lee, Hee Seock; Yeo, In Whan [Pohang Accelerator Laboratory, Pohang (Korea, Republic of)] (and others)

2001-03-15

The inspection program and the safety guidance were developed to enhance the radiation protection for the use of particle accelerators. First the classification of particle accelerators was conducted to develop the safety inspection protocol efficiently. The status of particle accelerators which were operated at the inside and outside of the country, and their safety programs were surveyed. The characteristics of radiation production was researched for each type of particle accelerators. Two research teams were launched for industrial and research accelerators and for medical accelerators, respectively. In each stages of a design, a fabrication, an installation, a commissioning, and normal operation of accelerators, those safety inspection protocols were developed. Because all protocols resulted from employing safety experts, doing the questionnaire, and direct facility surveys, it can be applicable to present safety problem directly. The detail improvement concepts were proposed to revise the domestic safety rule. This results might also be useful as a practical guidance for the radiation safety officer of an accelerator facility, and as the detail standard for the governmental inspection authorities.

Threshold guidance update

International Nuclear Information System (INIS)

Wickham, L.E.

1986-01-01

The Department of Energy (DOE) is developing the concept of threshold quantities for use in determining which waste materials must be handled as radioactive waste and which may be disposed of as nonradioactive waste at its sites. Waste above this concentration level would be managed as radioactive or mixed waste (if hazardous chemicals are present); waste below this level would be handled as sanitary waste. Last years' activities (1984) included the development of a threshold guidance dose, the development of threshold concentrations corresponding to the guidance dose, the development of supporting documentation, review by a technical peer review committee, and review by the DOE community. As a result of the comments, areas have been identified for more extensive analysis, including an alternative basis for selection of the guidance dose and the development of quality assurance guidelines. Development of quality assurance guidelines will provide a reasonable basis for determining that a given waste stream qualifies as a threshold waste stream and can then be the basis for a more extensive cost-benefit analysis. The threshold guidance and supporting documentation will be revised, based on the comments received. The revised documents will be provided to DOE by early November. DOE-HQ has indicated that the revised documents will be available for review by DOE field offices and their contractors

Request for Clarification of EPA Guidance on the Alternative Fuels Exemption under the PSD Program

Science.gov (United States)

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Nuclear Waste Management Program summary document, FY 1981

Energy Technology Data Exchange (ETDEWEB)

Meyers, Sheldon

1980-03-01

The Nuclear Waste Management Program Summary Document outlines the operational and research and development (R and D) activities of the Office of Nuclear Waste Management (NEW) under the Assistant Secretary for Nuclear Energy, US Department of Energy (DOE). This document focuses on the current and planned activities in waste management for FY 1981. This Program Summary Document (PSD) was prepared in order to explain the Federal nuclear waste management and spent fuel storage programs to Congress and its committees and to interested members of the public, the private sector, and the research community. The national energy policy as it applies to waste management and spent fuel storage is presented first. The program strategy, structure, budget, management approach, and public participation programs are then identified. The next section describes program activities and outlines their status. Finally, the applicability of departmental policies to NEW programs is summarized, including field and regional activities, commercialization plans, and environmental and socioeconomic implications of waste management activities, and international programs. This Nuclear Waste Management Program Summary Document is meant to serve as a guide to the progress of R and D and other energy technology programs in radioactive waste management. The R and D objective is to provide the Nation with acceptable solutions to short- and long-term management problems for all forms of radioactive waste and spent fuel.

Nuclear Waste Management Program summary document, FY 1981

International Nuclear Information System (INIS)

1980-03-01

The Nuclear Waste Management Program Summary Document outlines the operational and research and development (R and D) activities of the Office of Nuclear Waste Management (NEW) under the Assistant Secretary for Nuclear Energy, US Department of Energy (DOE). This document focuses on the current and planned activities in waste management for FY 1981. This Program Summary Document (PSD) was prepared in order to explain the Federal nuclear waste management and spent fuel storage programs to Congress and its committees and to interested members of the public, the private sector, and the research community. The national energy policy as it applies to waste management and spent fuel storage is presented first. The program strategy, structure, budget, management approach, and public participation programs are then identified. The next section describes program activities and outlines their status. Finally, the applicability of departmental policies to NEW programs is summarized, including field and regional activities, commercialization plans, and environmental and socioeconomic implications of waste management activities, and international programs. This Nuclear Waste Management Program Summary Document is meant to serve as a guide to the progress of R and D and other energy technology programs in radioactive waste management. The R and D objective is to provide the Nation with acceptable solutions to short- and long-term management problems for all forms of radioactive waste and spent fuel

Significant Guidance Issued by the Federal Transit Administration

Data.gov (United States)

Department of Transportation — A list of Significant Guidance documents, which include guidance document disseminated to regulated entities or the general public that may reasonably be anticipated...

Significant Guidance Issued by the Federal Aviation Administration

Data.gov (United States)

Department of Transportation — A list of Significant Guidance documents, which include guidance document disseminated to regulated entities or the general public that may reasonably be anticipated...

Significant Guidance Issued by the Federal Highway Administration

Data.gov (United States)

Department of Transportation — A list of Significant Guidance documents, which include guidance document disseminated to regulated entities or the general public that may reasonably be anticipated...

NASA-STD-7009 Guidance Document for Human Health and Performance Models and Simulations

Science.gov (United States)

Walton, Marlei; Mulugeta, Lealem; Nelson, Emily S.; Myers, Jerry G.

2014-01-01

Rigorous verification, validation, and credibility (VVC) processes are imperative to ensure that models and simulations (MS) are sufficiently reliable to address issues within their intended scope. The NASA standard for MS, NASA-STD-7009 (7009) [1] was a resultant outcome of the Columbia Accident Investigation Board (CAIB) to ensure MS are developed, applied, and interpreted appropriately for making decisions that may impact crew or mission safety. Because the 7009 focus is engineering systems, a NASA-STD-7009 Guidance Document is being developed to augment the 7009 and provide information, tools, and techniques applicable to the probabilistic and deterministic biological MS more prevalent in human health and performance (HHP) and space biomedical research and operations.

Toxic Substances Control Act. Environmental Guidance Program Reference Book: Revision 6

Energy Technology Data Exchange (ETDEWEB)

1992-05-15

This Reference Book contains a current copy of the Toxic Substances Control Act and those regulations that implement the statute and appear to be most relevant to DOE activities. The document is provided to DOE and contractor staff for informational purposes only and should not be interpreted as legal guidance. Questions concerning this Reference Book may be directed to Mark Petts, EH-231 (202/586-2609).

Environmental Guidance Program reference book: Toxic substances control act. Revision 7

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-01

This Reference Book contains a current copy of the Toxic Substances Control Act and those regulations that implement the statute and appear to be most relevant to DOE activities. The document is provided to DOE staff for informational purposes only and should not be interpreted as legal guidance. Questions concerning this Reference Book may be directed to Mark Petts, EH-231 (202/586-2609).

Guidance for implementing the long-term surveillance program for UMTRA Project Title I Disposal Sites

International Nuclear Information System (INIS)

1996-02-01

This guidance document has two purposes: it provides guidance for writing site-specific long-term surveillance plans (LTSP) and it describes site surveillance, monitoring, and long-term care techniques for Title I disposal sites of the Uranium Mill Tailings Radiation Control Act (UMTRCA) (42 USC Section 7901 et seq.). Long-term care includes monitoring, maintenance, and emergency measures needed to protect public health and safety and the environment after remedial action is completed. This document applies to the UMTRCA-designated Title I disposal sites. The requirements for long-term care of the Title I sites and the contents of the LTSPs are provided in U.S. Nuclear Regulatory Commission (NRC) regulations (10 CFR Section 40.27) provided in Attachment 1

Guidance document for preparing water sampling and analysis plans for UMTRA Project sites. Revision 1

International Nuclear Information System (INIS)

1995-09-01

A water sampling and analysis plan (WSAP) is prepared for each Uranium Mill Tailings Remedial Action (UMTRA) Project site to provide the rationale for routine ground water sampling at disposal sites and former processing sites. The WSAP identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the routine ground water monitoring stations at each site. This guidance document has been prepared by the Technical Assistance Contractor (TAC) for the US Department of Energy (DOE). Its purpose is to provide a consistent technical approach for sampling and monitoring activities performed under the WSAP and to provide a consistent format for the WSAP documents. It is designed for use by the TAC in preparing WSAPs and by the DOE, US Nuclear Regulatory Commission, state and tribal agencies, other regulatory agencies, and the public in evaluating the content of WSAPS

75 FR 69089 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2010-11-10

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-D-0514] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document... Administration (FDA) is announcing the availability of the guidance entitled ``Class II Special Controls Guidance...

76 FR 29251 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls; Guidance...

Science.gov (United States)

2011-05-20

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2006-D-0094] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls; Guidance Document... of the guidance entitled ``Guidance for Industry and Food and Drug Administration Staff; Class II...

Program information architecture/document hierarchy

International Nuclear Information System (INIS)

Woods, T.W.

1991-09-01

The Nuclear Waste Management System (NWMS) Management Systems Improvement Strategy (MSIS) (DOE 1990) requires that the information within the computer program and information management system be ordered into a precedence hierarchy for consistency. Therefore, the US Department of Energy (DOE). Office of Civilian Radioactive Waste Management (OCRWM) requested Westinghouse Hanford Company to develop a plan for NWMS program information which the MSIS calls a document hierarchy. This report provides the results of that effort and describes the management system as a ''program information architecture.'' 3 refs., 3 figs

Radiological emergency preparedness (REP) program

International Nuclear Information System (INIS)

Kwiatkowski, D.H.

1995-01-01

This talk focuses on the accomplishments of Radiological Emergency Preparedness Program. Major topics include the following: strengthening the partnership between FEMA, the States, and the Industry; the Standard Exercise Report Format (SERF); Multi-year performance partnership agreement (MYPPA); new REP Program guidance; comprehensive exercise program; federal radiological emergency response plan (FRERP); international interest; REP user fee; implementation EPA PAGs and Dose Limits; Contamination monitoring standard for portal monitors; guidance documents and training

Analysis of medical students' needs for development of a career guidance program.

Science.gov (United States)

An, Hyejin; Kim, Eunjeong; Hwang, Jinyoung; Lee, Seunghee

2014-09-01

The purpose of this study is to provide basic data for the development of a career guidance program through a demand survey. For this purpose, three study topics were examined: Is there a difference between the satisfaction and importance of a career program? Is there a difference between the satisfaction and importance of a career program by gender, grade level? and What type of mentor and the mentoring way of medical students demanded? The subjects were 380 students at Seoul National University College of Medicine. The data were analyzed by frequency analysis, paired t-test, and Borich's formula. By t-test with matched samples for satisfaction-importance, We noted statistically significant differences in all domains. In particular, the difference was greater in the second year. According to the needs analysis, the most urgent program is meeting with seniors in various career areas. Also, medical students hope for mentor from clinical professors of the university and successful medical practitioners, and personal counseling. These results show that medical students need a career guidance program. The findings of the study can be used to guide the development of career education programs and curriculum for medicine students.

77 FR 34390 - Draft Guidance for Industry: Amendment to “Guidance for Industry: Revised Preventive Measures To...

Science.gov (United States)

2012-06-11

... recommendations for plasma-derived products, including albumin and products containing plasma-derived albumin, in..., submit either electronic or written comments on the draft guidance by September 10, 2012. ADDRESSES... electronic access to the draft guidance document. Submit electronic comments on the draft guidance to http...

Guidance for a harmonized emission scenario document (ESD) on ballast water discharge

Energy Technology Data Exchange (ETDEWEB)

Zipperle, Andreas [BIS - Beratungszentrum fuer integriertes Sedimentmanagement, Hamburg (Germany); Gils, Jos van [DELTARES, Delft (Netherlands); Hattum, Bert van [Amsterdam Univ. (Netherlands). IVM - Institute for Environmental Studies; Heise, Susanne [BIS - Beratungszentrum fuer integriertes Sedimentmanagement, Hamburg (Germany); Hamburg Univ. of Applied Sciences (Germany)

2011-05-15

The present report provides guidance for a harmonized Emission Scenario Document (ESD) for the exposure assessment as part of the environmental risk assessment process which applicants seeking approval of a ballast water management system (BWMS) need to perform prior to notification and authorisation procedures. Despite the global variability of the marine environment, ballast water discharges and treatment methods, exposure assessments need to be comparable between different applications. In order to achieve this, this ESD points out the following aspects: - Applicants should use standardized scenarios in order to predict mean exposure. These should reflect generic situations, independent of region or port so that results are widely applicable. In addition to a harbour scenario, a standardized shipping lane scenario should be considered, - During or right after ballast water discharge, high concentrations may persist in a water body for a certain length of time until extensive mixing results in mean concentrations. Not taking exposure to peak concentrations within gradients into account could lead to an underestimation of risk, especially for rapidly degrading substances. Efforts have been made to approximate maximum exposure concentration with simple dilution factors. Their applicability was checked by near-field-evaluations. - Chemical properties determine the environmental fate of substances. If they are ambiguous, selection of a specific set of data strongly influences the result of an exposure assessment. Guidance is given on what to do about lacking data. - In order to harmonize the exposure assessments, reliable chemical model software should be used. A discussion on the requirements of suitable software and an evaluation of MAMPEC is given in this report. (orig.)

CH Packaging Program Guidance

International Nuclear Information System (INIS)

Washington TRU Solutions LLC

2003-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SARP charges the WIPP management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 CFR 71.11. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. This document provides the instructions to be followed to operate, maintain, and test the TRUPACT-II and HalfPACT packaging. The intent of these instructions is to standardize operations. All users will follow these instructions or equivalent instructions that assure operations are safe and meet the requirements of the SARPs

CH Packaging Program Guidance

International Nuclear Information System (INIS)

Washington TRU Solutions LLC

2002-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT Shipping Package, and directly related components. This document complies with the minimum requirements as specified in TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event there is a conflict between this document and the SARP or C of C, the SARP and/or C of C shall govern. C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SAR P charges the WIPP Management and Operation (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 CFR 71.11. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. This document details the instructions to be followed to operate, maintain, and test the TRUPACT-II and HalfPACT packaging. The intent of these instructions is to standardize these operations. All users will follow these instructions or equivalent instructions that assure operations are safe and meet the requirements of the SARPs

Significant Guidance Issued by the Federal Motor Carrier Safety Administration

Data.gov (United States)

Department of Transportation — A list of Significant Guidance documents, which include guidance document disseminated to regulated entities or the general public that may reasonably be anticipated...

Environmental guidance documents for exploration, development, Production, and transportation of crude oil and natural gas in texas: Quarterly technical report, January 1, 1997-March 31, 1997

International Nuclear Information System (INIS)

Savage, L.

1997-01-01

The following technical report provides a detailed status report of the DOE grant project entitled ''Environmental Guidance Documents for Exploration, Development, Production, and Transportation of Crude Oil and Natural Gas in Texas.'' The grant funding allocated is for the purpose of provided the Railroad Commission of Texas (Commission) with resources and capabilities to draft, publish and distribute documents that provide guidance to oil and gas operators on issues concerning oil and gas naturally occurring radioactive material (NORM) waste, oil and gas hazardous waste, remediation of crude oil spills, management of non-hazardous oil and gas wastes, and mechanical integrity testing of Class II injection and disposal wells

Final technical position on documentation of computer codes for high-level waste management

International Nuclear Information System (INIS)

Silling, S.A.

1983-06-01

Guidance is given for the content of documentation of computer codes which are used in support of a license application for high-level waste disposal. The guidelines cover theoretical basis, programming, and instructions for use of the code

Guidance system operations plan for manned CSM earth orbital and lunar missions using program COLOSSUS 3. Section 7: Erasable memory programs

Science.gov (United States)

Hamilton, M. H.

1972-01-01

Erasable-memory programs designed for guidance computers used in command and lunar modules are presented. The purpose, functional description, assumptions, restrictions, and imitations are given for each program.

Guidelines for the documentation of digital computer programs - approved 1974

International Nuclear Information System (INIS)

Anon.

1975-01-01

This standard presents guidelines for the documentation of engineering and scientific computer programs. Good documentation promotes understanding, reduces duplication of effort, eases conversion to different computer environments and aids modification for extended applications. Good documentation is essential for implementation and effective use of programs obtained from other installations. Since the intention of this standard is to encourage better communication between the developer and user, it should be regarded as a guide rather than a set of rigid specifications. As a guide, it is sufficiently comprehensive to apply to large-scale programs intended for extensive external use. Not all features of this document are appropriate in all circumstances. In general, as the project complexity increases so does the need for more complete documentation. An organization may have special documentation requirements which supersede or extend these guidelines. This standard is a revision of ANS-STD.2-1967 and supersedes it

Environmental monitoring guidance for DOE Order 5820.2A, Chapter 3

International Nuclear Information System (INIS)

Dolenc, M.R.

1988-01-01

The Defense Low-Level Waste Management Program (DLLWMP) is preparing guidance to support the requirements outlined in DOE Order 5820.2A, Chapter 3, Management of Low-Level Waste. One of these documents is the Environmental Monitoring Guidance. Environmental monitoring is required for all operational and nonoperational treatment, storage, and disposal facilities to ensure that the facility conforms to all appropriate DOE orders. An adequate environmental monitoring program must be designed to measure key parameters that may affect both short- and long-term site performance. These parameters include measuring both chemical and radiological releases in surface soil, air, surface water, flora, fauna, and subsurface soil and groundwater, both in the saturated and unsaturated zones. The monitoring program must be capable of detecting performance trends in sufficient time to allow corrective action before the facility exceeds performance objectives. The program should also provide the data input necessary to evaluate the performance assessment of the facility. This paper outlines the approach being planned to accomplish these tasks

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2005-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SARP charges the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.

Guidance system operations plan for manned CM earth orbital missions using program SKYLARK 1. Section 4: Operational modes

Science.gov (United States)

Dunbar, J. C.

1972-01-01

The operational modes for the guidance system operations plan for Program SKYLARK 1 are presented. The procedures control the guidance and navigation system interfaces with the flight crew and the mission control center. The guidance operational concept is designed to comprise a set of manually initiated programs and functions which may be arranged by the flight crew to implement a large class of flight plans. This concept will permit both a late flight plan definition and a capability for real time flight plan changes.

Requirements, guidance and logic in planning environmental investigations: Approval versus implementation

International Nuclear Information System (INIS)

Brice, D.A.; Meredith, D.V.; Harris, M.Q.

1993-01-01

In today's litigious society, it is important for both private parties and government to plan and conduct environmental investigations in a scientifically sound manner, documenting the purpose, methods, and results in a consistent fashion throughout the exercise. Planning documents are prepared during the initial phases of environmental investigations. Project objectives, including data quality requirements, specific work to be conducted to fulfill data needs, and operating procedures are specified. Regulatory agency approval of these documents is often required prior to plan implementation. These approvals are necessary and appropriate to fulfilling the agency's mandated role. Many guidance documents prepared by regulatory agencies suggest the content and format of various scoping documents. These guidances help standardize thought processes and considerations in planning, and provide a template to ensure that both the plan and the proposed work will fulfill regulatory requirements. This work describes the preparation and use of guidance documents for planning environmental studies. The goals and some of the pitfalls of such documents are discussed. Guidance should include the following elements: the purpose of the guidance and a description of where it applies; the type of items to be addressed in planning; identification of requirements are applicable to all projects for which the guidance is intended; identification of requirements only applicable in certain situations; a description of items to facilitate planning; a suggested format for fulfilling requirements; example applications of the guidance. Disagreements arise between planners and reviewers/approvers when elements of guidance are used as leverage to require work not directly related to project objectives. Guidance may be inappropriately used as a milestone by which site-specific plans are judged. Regulatory agency review and approval may be regarded as a primary objective of the plan

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2006-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant| (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations(CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2007-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

Concept document of the repository-based software engineering program: A constructive appraisal

Science.gov (United States)

1992-01-01

A constructive appraisal of the Concept Document of the Repository-Based Software Engineering Program is provided. The Concept Document is designed to provide an overview of the Repository-Based Software Engineering (RBSE) Program. The Document should be brief and provide the context for reading subsequent requirements and product specifications. That is, all requirements to be developed should be traceable to the Concept Document. Applied Expertise's analysis of the Document was directed toward assuring that: (1) the Executive Summary provides a clear, concise, and comprehensive overview of the Concept (rewrite as necessary); (2) the sections of the Document make best use of the NASA 'Data Item Description' for concept documents; (3) the information contained in the Document provides a foundation for subsequent requirements; and (4) the document adequately: identifies the problem being addressed; articulates RBSE's specific role; specifies the unique aspects of the program; and identifies the nature and extent of the program's users.

Standardization Documents

Science.gov (United States)

2011-08-01

Specifications and Standards; Guide Specifications; CIDs; and NGSs . Learn. Perform. Succeed. STANDARDIZATION DOCUMENTS Federal Specifications Commercial...national or international standardization document developed by a private sector association, organization, or technical society that plans ...Maintain lessons learned • Examples: Guidance for application of a technology; Lists of options Learn. Perform. Succeed. DEFENSE HANDBOOK

Significant Guidance Issued by the Office of the Secretary of Transportation

Data.gov (United States)

Department of Transportation — A list of Significant Guidance documents, which include guidance document disseminated to regulated entities or the general public that may reasonably be anticipated...

FDA (Food and Drug Administration) Compliance Program Guidance Manual (FY 88). Section 4. Medical and radiological devices

International Nuclear Information System (INIS)

1988-01-01

The FDA Compliance Program Guidance Manual provides a system for issuing and filing program plans and instructions directed to Food and Drug Administration Field operations for project implementation. Section IV provides those chapters of the Compliance Program Guidance Manual which pertain to the areas of medical and radiological devices. Some of the areas of coverage include laser and sunlamp standards inspections, compliance testing of various radiation-emitting products such as television receivers and microwave ovens, emergency response planning and policy, premarket approval and device manufacturers inspections, device problem reporting, sterilization of devices, and consumer education programs on medical and radiological devices

HANDBOOK: HAZARDOUS WASTE INCINERATION MEASUREMENT GUIDANCE

Science.gov (United States)

This publication, Volume III of the Hazardous Waste Incineration Guidance Series, contains general guidance to permit writers in reviewing hazardous waste incineration permit applications and trial burn plans. he handbook is a how-to document dealing with how incineration measure...

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2008-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the pplication.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2009-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

Test plan guidance for transuranic-contaminated arid landfill remedial technology development

International Nuclear Information System (INIS)

Evans, J.; Shaw, P.

1995-05-01

This document provides guidance for preparing plans to test or demonstrate buried waste assessment or remediation technologies supported by the U.S. Department of Energy's Landfill Stabilization Focus Area, Transuranic-Contaminated Arid Landfill Product Line. This document also provides guidance for development of data quality objectives, along with the necessary data to meet the project objectives. The purpose is to ensure that useful data of known quality are collected to support conclusions associated with the designated demonstration or test. A properly prepared test plan will integrate specific and appropriate objectives with needed measurements to ensure data will reflect the Department of Energy Office of Technology Development's mission, be consistent with Landfill Stabilization Focus Area test goals, and be useful for the Department of Energy Environmental Restoration and Waste Management programs and other potential partners (e.g., commercial concerns). The test plan becomes the planning and working document for the demonstration or test to be conducted ensuring procedures are followed that will allow data of sufficient quality to be collected for comparison and evaluation

PSD Increment Consumption Guidance

Science.gov (United States)

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Guidance on the application of quality assurance for characterizing a low-level radioactive waste disposal site

International Nuclear Information System (INIS)

Pittiglio, C.L. Jr.; Starmer, R.J.; Hedges, D.

1990-10-01

This document provides the Nuclear Regulatory Commission's staff guidance to an applicant on meeting the quality control (QC) requirements of Title 10 of the Code of Federal Regulations, Part 61, Section 61.12 (10 CFR 61.12), for a low-level waste disposal facility. The QC requirements combined with the requirements for managerial controls and audits are the basis for developing a quality assurance (QA) program and for the guidance provided herein. QA guidance is specified for site characterization activities necessary to meet the performance objectives of 10 CFR Part 61 and to limit exposure to or the release of radioactivity. 1 tab

PSP Program close out documentation

Energy Technology Data Exchange (ETDEWEB)

Andringa, K.; Hootman, H.E.; Ferrara, A.S.; Smith, P.K.; Congdon, J.W.; Randolph, H.W.; Young, R.H.; Driggers, F.E.; Topp, S.V.

1985-12-31

In December 1982 DOE-SR directed SRL to study the feasibility and impact of a program to lower the U-236 content of the Highly Enriched Uranium (HEU) stockpile used as fuel for the SRP reactors. In response to this request SRL assessed four technologies, Atomic Vapor Laser Isotope Separation (AVLIS), Molecular Laser Isotope Separation (MLIS), Gas Centrifuge, and the Plasma Separation Process (PSP) for this purpose with the assistance of the Engineering Department. In April 1983 cost/benefit analyses for these processes, high spot cost estimates for production facilities, and process uncertainties were submitted to DOE-SR with a recommendation to proceed with the conceptual design and supporting development programs for a facility based on the use of the PSP process. The current program status for the PSP development program at SRL and the design and documentation of a production facility at SRP, referred to as the Fuel Improvement Demonstration Facility (FIDF), is described in this report.

Apollo guidance, navigation and control: Guidance system operations plans for manned LM earth orbital and lunar missions using Program COLOSSUS 3. Section 7: Erasable memory programs

Science.gov (United States)

Hamilton, M. H.

1972-01-01

Erasable-memory programs (EMPs) designed for the guidance computers used in the command (CMC) and lunar modules (LGC) are described. CMC programs are designated COLOSSUS 3, and the associated EMPs are identified by a three-digit number beginning with 5. LGC programs are designated LUMINARY 1E, and the associated EMPs are identified, with one exception, by a three-digit number beginning with 1. The exception is EMP 99. The EMPs vary in complexity from a simple flagbit setting to a long and intricate logical structure. They all, however, cause the computer to behave in a way not intended in the original design of the programs; they accomplish this off-nominal behavior by some alteration of erasable memory to interface with existing fixed-memory programs to effect a desired result.

The integrated performance evaluation program quality assurance guidance in support of EM environmental sampling and analysis activities

International Nuclear Information System (INIS)

1994-05-01

EM's (DOE's Environmental Restoration and Waste Management) Integrated Performance Evaluation Program (IPEP) has the purpose of integrating information from existing PE programs with expanded QA activities to develop information about the quality of radiological, mixed waste, and hazardous environmental sample analyses provided by all laboratories supporting EM programs. The guidance addresses the goals of identifying specific PE sample programs and contacts, identifying specific requirements for participation in DOE's internal and external (regulatory) programs, identifying key issues relating to application and interpretation of PE materials for EM headquarters and field office managers, and providing technical guidance covering PE materials for site-specific activities. (PE) Performance Evaluation materials or samples are necessary for the quality assurance/control programs covering environmental data collection

76 FR 43690 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2011-07-21

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2007-D-0149] (Formerly 2007D-0309) Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document: Electrocardiograph Electrodes; Availability AGENCY: Food and Drug...

77 FR 14403 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2012-03-09

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-D-0167] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document: Norovirus Serological Reagents; Availability AGENCY: Food and Drug Administration, HHS. ACTION: Notice...

Department of Defense high power laser program guidance

Science.gov (United States)

Muller, Clifford H.

1994-06-01

The DoD investment of nominally $200 million per year is focused on four high power laser (HPL) concepts: Space-Based Laser (SBL), a Ballistic Missile Defense Organization effort that addresses boost-phase intercept for Theater Missile Defense and National Missile Defense; Airborne Laser (ABL), an Air Force effort that addresses boost-phase intercept for Theater Missile Defense; Ground-Based Laser (GBL), an Air Force effort addressing space control; and Anti-Ship Missile Defense (ASMD), a Navy effort addressing ship-based defense. Each organization is also supporting technology development with the goal of achieving less expensive, brighter, and lighter high power laser systems. These activities represent the building blocks of the DoD program to exploit the compelling characteristics of the high power laser. Even though DoD's HPL program are focused and moderately strong, additional emphasis in a few technical areas could help reduce risk in these programs. In addition, a number of options are available for continuing to use the High-Energy Laser System Test Facility (HELSTF) at White Sands Missile Range. This report provides a brief overview and guidance for the five efforts which comprise the DoD HPL program (SBL, ABL, GBL, ASMD, HELSTF).

Draft federal GHG accounting and reporting : technical support document

Science.gov (United States)

2010-07-01

This is a technical support document (TSD) that accompanies the Federal Greenhouse Gas Accounting and Reporting Guidance (or Guidance). This document provides detailed information on the inventory reporting process and accepted calculation methodolog...

The Engineering Compliance Program development process and its role in design

International Nuclear Information System (INIS)

1997-12-01

This paper presents an overview of the Engineering Compliance Program (ECP) development process and its role in design. The ECP is a formal program to assess Nuclear Regulatory Commission (NRC) regulatory guidance in terms of precedence, industry experience documents, and codes and standards to determine their applicability to Mined Geologic Disposal System (MGDS) design. These determinations are documented in ECP Guidance Packages for MGDS Structures, Systems and Components (SSCs). This ensures that the license application appropriately reflects the MGDS design and facilitates NRC acceptance and compliance review

76 FR 48870 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2011-08-09

... selection inclusion and exclusion criteria section. The revisions define and differentiate the required... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-D-0428] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document...

76 FR 20992 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2011-04-14

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-D-0189] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document: Low Level Laser System for Aesthetic Use; Availability AGENCY: Food and Drug Administration, HHS...

75 FR 68364 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2010-11-05

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2008-D-0275] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document: Full-Field Digital Mammography System; Availability AGENCY: Food and Drug Administration, HHS. [[Page...

76 FR 16425 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2011-03-23

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-D-0028] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document: Ovarian Adnexal Mass Assessment Score Test System; Availability AGENCY: Food and Drug Administration, HHS...

76 FR 6622 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2011-02-07

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-D-0645] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document: Contact Cooling System for Aesthetic Use; Availability AGENCY: Food and Drug Administration, HHS. ACTION...

76 FR 22906 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2011-04-25

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2006-D-0094] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document: Topical Oxygen Chamber for Extremities; Availability AGENCY: Food and Drug Administration, HHS. ACTION...

76 FR 43332 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2011-07-20

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-D-0500] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document: Focused Ultrasound Stimulator System for Aesthetic Use; Availability AGENCY: Food and Drug Administration...

75 FR 70271 - Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance...

Science.gov (United States)

2010-11-17

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-D-0515] Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document...: Food and Drug Administration, HHS. ACTION: Notice. SUMMARY: The Food and Drug Administration (FDA) is...

Environmental Guidance Program Reference Book: Comprehensive Environmentally Response, Compensation, and Liability Act

Energy Technology Data Exchange (ETDEWEB)

1991-12-31

This Reference Book contains a current copy of the Comprehensive Environmental Response Compensation, and Liability Act and those regulations that implement the statute and appear to be most relevant to Department of Energy (DOE) activities. The document is provided to DOE and contractor staff for informational purposes only and should not be interpreted as legal guidance. Updates that include important new requirements will be provided periodically. Questions concerning this Reference Book may be directed to Mark Petts, EH-231 (FTS 896-2609 or Commercial 202/586-2609).

Interim Reliability Evaluation Program procedures guide

International Nuclear Information System (INIS)

Carlson, D.D.; Gallup, D.R.; Kolaczkowski, A.M.; Kolb, G.J.; Stack, D.W.; Lofgren, E.; Horton, W.H.; Lobner, P.R.

1983-01-01

This document presents procedures for conducting analyses of a scope similar to those performed in Phase II of the Interim Reliability Evaluation Program (IREP). It documents the current state of the art in performing the plant systems analysis portion of a probabilistic risk assessment. Insights gained into managing such an analysis are discussed. Step-by-step procedures and methodological guidance constitute the major portion of the document. While not to be viewed as a cookbook, the procedures set forth the principal steps in performing an IREP analysis. Guidance for resolving the problems encountered in previous analyses is offered. Numerous examples and representative products from previous analyses clarify the discussion

Hazardous waste landfill research: U. S. E. P. A. (United States Environmental Protection Agency) Program

Energy Technology Data Exchange (ETDEWEB)

Schomaker, N.B.

1984-06-01

The hazardous waste land disposal research program is collecting data necessary to support implementation of disposal guidelines mandated by the 'Resource Conservation and Recovery Act of 1976' (RCRA) PL 94-580. This program relating to the categorical areas of landfills, surface impoundments, and underground mines encompasses state-of-the-art documents, laboratory analysis, economic assessment, bench and pilot studies, and full-scale field verification studies. Over the next five years the research will be reported as Technical Resource Documents in support of the RCRA Guidance Documents. These documents will be used to provide guidance for conducting the review and evaluation of land disposal permit applications. This paper will present an overview of this program and will report the current status of the work.

76 FR 61098 - Guidance for 1-Hour SO2

Science.gov (United States)

2011-10-03

...Notice is hereby given that the EPA has posted its draft non- binding guidance titled, ``Guidance for 1-Hour SO2 NAAQS SIP Submissions'' on its Web site. The EPA invites public comments on this guidance document during the comment period specified below, and plans to issue an updated version of the guidance after reviewing timely submitted comments.

NPP License Renewal and Aging Management: Revised Guidance

International Nuclear Information System (INIS)

Hull, A.B.; Hiser, A.L.; Lindo-Talin, S.E.

2012-01-01

Based on the Atomic Energy Act, the NRC issues licenses for commercial power reactors to operate for up to 40 years and allows these licenses to be renewed for up to another 20 years. NRC has approved license renewal (LR) for well over 50% of U.S. located reactors originally licensed to operate for 40 years. Of these 104 reactors (69 PWRs, 35 BWRs), the NRC has issued renewed licenses for 71 units and is currently reviewing applications for another 15 units. As of May 1, 2012, ten plants at nine sites had entered their 41st year of operation and thus are in their first period of extended operation (PEO). Five more plants will enter the PEO by the end of 2012. One foundation of the license renewal process has been license renewal guidance documents (LRGDs). The U.S. Nuclear Regulatory Commission (NRC) revised key guidance documents used for nuclear power LR in 2010 and 2011. These include NUREG-1800, 'Standard Review Plan for Review of License Renewal Applications,' revision 2 (SRP-LR), and NUREG-1801, 'Generic Aging Lessons Learned (GALL) Report,' revision 2 (GALL Report). The guidance documents were updated to reflect lessons learned and operating experience gained since the guidance documents were last issued in 2005. The reactor LRGDs referenced in this poster can all be accessed at http://www.nrc.gov/reactors/operating/licensing/renewal/guidance.html (author)

Guidance document for prepermit bioassay testing of low-level radioactive waste

International Nuclear Information System (INIS)

Anderson, S.L.; Harrison, F.L.

1990-11-01

In response to the mandate of Public Law 92-532, the Marine Protection, Research, and Sanctuaries Act (MPRSA) of 1972, as amended, the Environmental Protection Agency (EPA) has developed a program to promulgate regulations and criteria to control the ocean disposal of radioactive wastes. The EPA seeks to understand the mechanisms for biological response of marine organisms to the low levels of radioactivity that may arise from the release of these wastes as a result of ocean-disposal practices. Such information will play an important role in determining the adequacy of environmental assessments provided to the EPA in support of any disposal permit application. Although the EPA requires packaging of low-level radioactive waste to prevent release during radiodecay of the materials, some release of radioactive material into the deep-sea environment may occur when a package deteriorates. Therefore, methods for evaluating the impact on biota are being evaluated. Mortality and phenotypic responses are not anticipated at the expected low environmental levels that might occur if radioactive materials were released from the low-level waste packages. Therefore, traditional bioassay systems are unsuitable for assessing sublethal effects on biota in the marine environment. The EPA Office of Radiation Programs (ORP) has had an ongoing program to examine sublethal responses to radiation at the cellular level, using cytogenetic end points. This technical guidance report represents prepermit bioassay procedures that potentially may be applicable to the assessment of effects from a mixture of radionuclides that could be released from a point source at the ocean bottom. Methodologies along with rationale and a discussion of uncertainty are presented for the sediment benthic bioassay protocols identified in this report

Guidance document for prepermit bioassay testing of low-level radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Anderson, S.L.; Harrison, F.L.

1990-11-01

In response to the mandate of Public Law 92-532, the Marine Protection, Research, and Sanctuaries Act (MPRSA) of 1972, as amended, the Environmental Protection Agency (EPA) has developed a program to promulgate regulations and criteria to control the ocean disposal of radioactive wastes. The EPA seeks to understand the mechanisms for biological response of marine organisms to the low levels of radioactivity that may arise from the release of these wastes as a result of ocean-disposal practices. Such information will play an important role in determining the adequacy of environmental assessments provided to the EPA in support of any disposal permit application. Although the EPA requires packaging of low-level radioactive waste to prevent release during radiodecay of the materials, some release of radioactive material into the deep-sea environment may occur when a package deteriorates. Therefore, methods for evaluating the impact on biota are being evaluated. Mortality and phenotypic responses are not anticipated at the expected low environmental levels that might occur if radioactive materials were released from the low-level waste packages. Therefore, traditional bioassay systems are unsuitable for assessing sublethal effects on biota in the marine environment. The EPA Office of Radiation Programs (ORP) has had an ongoing program to examine sublethal responses to radiation at the cellular level, using cytogenetic end points. This technical guidance report represents prepermit bioassay procedures that potentially may be applicable to the assessment of effects from a mixture of radionuclides that could be released from a point source at the ocean bottom. Methodologies along with rationale and a discussion of uncertainty are presented for the sediment benthic bioassay protocols identified in this report.

NPP License Renewal and Aging Management: Revised Guidance

International Nuclear Information System (INIS)

Hull, A.B.; Hiser, A.L.; Lindo-Talin, S.E.

2012-01-01

Based on the Atomic Energy Act, the NRC issues licenses for commercial power reactors to operate for up to 40 years and allows these licenses to be renewed for up to another 20 years. NRC has approved license renewal for well over 50% of U.S. located reactors originally licensed to operate for 40 years. Of these 104 reactors (69 PWRs, 35 BWRs), the NRC has issued renewed licenses for 71 units and is currently reviewing applications for another 15 units. As of May 1, 2012, ten plants at nine sites had entered their 41st year of operation and thus are in their first period of extended operation (PEO). Five more plants will enter the PEO by the end of 2012. One foundation of the license renewal process has been license renewal guidance documents (LRGDs). The U.S. Nuclear Regulatory Commission (NRC) revised key guidance documents used for nuclear power license renewal in 2010 and 2011. These include NUREG-1800, 'Standard Review Plan for Review of License Renewal Applications,' revision 2 (SRP-LR), and NUREG-1801, 'Generic Aging Lessons Learned (GALL) Report,' revision 2 (GALL Report). The guidance documents were updated to reflect lessons learned and operating experience gained since the guidance documents were last issued in 2005. (author)

Implications of DOE O 1027 Guidance on Rad-NESHAP Programs

International Nuclear Information System (INIS)

Fuehne, David P.; Fong, Stephen C.

2012-01-01

This presentation is for the national Radionuclide NESHAP meeting, an embedded topic of the 2012 Health Physics Society Annual Meeting in Sacramento, CA. The Radionuclide NESHAP program is responsible for measuring and reporting the amount of airborne radioactive material released from DOE facilities. The issue at hand is recent guidance put forth by the Department of Energy regarding threshold limits for Category 3 and Category 2 nuclear facilities. Updates to calculation methods have resulted in increased amounts of radioactive material allowed in inventory for facilities before they reach levels which require them to be categorized as a Category 2 or 3 nuclear facility. With larger radioactive material inventories, there may be a corresponding increase in overall facility emissions. This can have permitting and monitoring impacts for DOE sites, as well as political ramifications with citizen organizations. This presentation is intended to raise awareness of the new guidance and associated issues, and to stimulate discussion among DOE Radionuclide NESHAP representatives.

Guidance for closure of existing DOE LLW disposal sites

International Nuclear Information System (INIS)

Blanchfield, L.

1987-01-01

During FY 1986, a closure guidance document was developed. The purpose of this document is to provide guidance in support of DOE Order 5820.2 to site operating contractors for the stabilization and closure of existing low-level waste (LLW) shallow land disposal sites at US Department of Energy (DOE) facilities. Guidance is provided to aid operators in placing existing LLW sites in a closed conditions, i.e., a condition in which a nonoperational site meets postclosure performance requirements and can be shown, within a high degree of confidence, to perform as anticipated in the future, under the most cost-effective maintenance approach. Guidance is based on the philosophy that closure should be planned and performed using a systems approach. Plans for FY 1987 call for revision of the document to incorporate more information on closure of LLW sites also containing radioactive mixed waste and/or transuranic waste. 4 references, 3 figures, 2 tables

Streamlining of the Decontamination and Demolition Document Preparation Process

International Nuclear Information System (INIS)

Durand, Nick; Meincke, Carol; Peek, Georgianne

1999-01-01

During the past five years, the Sandia National Labo- ratories Decontamination, Decommissioning, Demolition, and Reuse (D3R) Program has evolved and become more focused and efficient. Historical approaches to project documentation, requirements, and drivers are discussed detailing key assumptions, oversight authority, and proj- ect approvals. Discussion of efforts to streamline the D3R project planning and preparation process include the in- corporation of the principles of graded approach, Total Quality Management, and the Observational Method (CH2MHILL April 1989).1 Process improvements were realized by clearly defining regulatory requirements for each phase of a project, establishing general guidance for the program and combining project-specific documents to eliminate redundant and unneeded information. Proc- ess improvements to cost, schedule, and quality are dis- cussed in detail for several projects

Equal employment opportunity plan development guidance

Energy Technology Data Exchange (ETDEWEB)

None

1978-09-01

The purpose of this publication is to provide instructions for the development of EEO Plans for Fiscal Year 1979. It supplements the National EEO Plan for the Department of Energy issued in August 1978 (DOE/S-0002). The material included should be used immediately as guidance to develop, document, and implement subordinate echelon commitments to EEO. A schedule for the development and submission of EEO Plans is included. Most of the continuing requirements will be published at a later date as part of the directives system. Any comments or helpful suggestions concerned with the program outlined would be appreciated by the Office of Equal Opportunity.

High-level waste storage tank farms/242-A evaporator standards/requirements identification document (S/RID), Vol. 7

Energy Technology Data Exchange (ETDEWEB)

1994-04-01

This Requirements Identification Document (RID) describes an Occupational Health and Safety Program as defined through the Relevant DOE Orders, regulations, industry codes/standards, industry guidance documents and, as appropriate, good industry practice. The definition of an Occupational Health and Safety Program as specified by this document is intended to address Defense Nuclear Facilities Safety Board Recommendations 90-2 and 91-1, which call for the strengthening of DOE complex activities through the identification and application of relevant standards which supplement or exceed requirements mandated by DOE Orders. This RID applies to the activities, personnel, structures, systems, components, and programs involved in maintaining the facility and executing the mission of the High-Level Waste Storage Tank Farms.

High-level waste storage tank farms/242-A evaporator standards/requirements identification document (S/RID), Vol. 7

International Nuclear Information System (INIS)

1994-04-01

This Requirements Identification Document (RID) describes an Occupational Health and Safety Program as defined through the Relevant DOE Orders, regulations, industry codes/standards, industry guidance documents and, as appropriate, good industry practice. The definition of an Occupational Health and Safety Program as specified by this document is intended to address Defense Nuclear Facilities Safety Board Recommendations 90-2 and 91-1, which call for the strengthening of DOE complex activities through the identification and application of relevant standards which supplement or exceed requirements mandated by DOE Orders. This RID applies to the activities, personnel, structures, systems, components, and programs involved in maintaining the facility and executing the mission of the High-Level Waste Storage Tank Farms

Clean Water Act (excluding Section 404). Environmental guidance program reference book: Revision 6

Energy Technology Data Exchange (ETDEWEB)

1993-01-15

This Reference Book contains a current copy of the Clean Water Act (excluding Section 404) and those regulations that implement the statutes and appear to be most relevant to US Department of Energy (DOE) activities. The document is provided to DOE and contractor staff for informational purposes only and should not be interpreted as legal guidance. Updates that include important new requirements will be provided periodically. Questions concerning this Reference Book may be directed to Mark Petts, EH-231 (202/586-2609).

Standards for maintenance documentation of COSMOS programs

International Nuclear Information System (INIS)

Burstall, R.F.; Rickets, T.M.; Butland, A.T.D.

1982-06-01

The Compatible Open Shop Modular Operating Scheme (COSMOS) is used for fast reactor neutronics and subassembly distortion calculations in the UK. It provides database and databank facilities for this purpose. A large number of applications programs use these facilities. This report sets down the standards agreed for use in the preparation of maintenance documents for these programs. These standards have been developed as the result of experience with earlier more complicated standards. Some of the terminology used in this report is particular to COSMOS, but the general features of the standard may be useful to those responsible for other computer programs. (author)

75 FR 70254 - PSD and Title V Permitting Guidance for Greenhouse Gases

Science.gov (United States)

2010-11-17

... Guidance for Greenhouse Gases AGENCY: Environmental Protection Agency (EPA). ACTION: Notice of availability..., ``PSD and Title V Permitting Guidance for Greenhouse Gases'' on its significant guidance Internet Web... guidance titled, ``PSD and Title V Permitting Guidance for Greenhouse Gases.'' This document has been...

Planning, Conducting, and Documenting Data Analysis for Program Improvement

Science.gov (United States)

Winer, Abby; Taylor, Cornelia; Derrington, Taletha; Lucas, Anne

2015-01-01

This 2015 document was developed to help technical assistance (TA) providers and state staff define and limit the scope of data analysis for program improvement efforts, including the State Systemic Improvement Plan (SSIP); develop a plan for data analysis; document alternative hypotheses and additional analyses as they are generated; and…

Large Hospital 50% Energy Savings: Technical Support Document

Energy Technology Data Exchange (ETDEWEB)

Bonnema, E.; Studer, D.; Parker, A.; Pless, S.; Torcellini, P.

2010-09-01

This Technical Support Document documents the technical analysis and design guidance for large hospitals to achieve whole-building energy savings of at least 50% over ANSI/ASHRAE/IESNA Standard 90.1-2004 and represents a step toward determining how to provide design guidance for aggressive energy savings targets. This report documents the modeling methods used to demonstrate that the design recommendations meet or exceed the 50% goal. EnergyPlus was used to model the predicted energy performance of the baseline and low-energy buildings to verify that 50% energy savings are achievable. Percent energy savings are based on a nominal minimally code-compliant building and whole-building, net site energy use intensity. The report defines architectural-program characteristics for typical large hospitals, thereby defining a prototype model; creates baseline energy models for each climate zone that are elaborations of the prototype models and are minimally compliant with Standard 90.1-2004; creates a list of energy design measures that can be applied to the prototype model to create low-energy models; uses industry feedback to strengthen inputs for baseline energy models and energy design measures; and simulates low-energy models for each climate zone to show that when the energy design measures are applied to the prototype model, 50% energy savings (or more) are achieved.

Guidance for preparing user requirements documents for small and medium reactors and their application

International Nuclear Information System (INIS)

2000-08-01

During the past decade, several countries with highly developed nuclear power programs established user required documents (URDs) to guide the development and implementation of advanced light water reactors. These efforts built upon the extensive experience with operating reactors and included new insights from ongoing research and development to enhance the economic performance and safety of future nuclear power plants. Subsequently, a number of developing countries with plans for introducing nuclear energy into their national programs expressed strong interest in establishing analogous requirements. The IAEA has therefore taken the initiative to assist in the elaboration of such requirements. Building upon relevant documents this report recommends a URD structure and content outline to support developing countries in preparing their URDs for various applications of small and medium reactors (e.g. electricity generation and/or desalination). This report was prepared by representatives from both developing and developed Member States

Moisture Control Guidance for Commercial and Public ...

Science.gov (United States)

This document provides guidance to designers, construction mangers, and building operation/maintenance managers to improve IEQ and reduce risks of encountering IEQ problems due to insufficient moisture control. EPA will be producing a document entitled

76 FR 66925 - Guidance for 1-Hour SO2

Science.gov (United States)

2011-10-28

...The EPA is announcing an extension of the public comment period for its draft non-binding guidance titled, ``Guidance for 1-Hour SO2 SIP Submissions.'' The draft of the guidance document is currently on the EPA's Web site. The EPA is extending the comment period for an additional 30-day period and invites public comments on this guidance during this period. The EPA plans to issue an updated version of the guidance after reviewing timely submitted comments.

Best Available Technology (economically achievable) guidance document for the Hanford Site

International Nuclear Information System (INIS)

1988-07-01

This document provides Westinghouse Hanford Company (Westinghouse Hanford) and the US Department of Energy (DOE) with a step-by-step procedure for the identification and documentation of the Best Available Technology (BAT) economically achievable for treating liquid effluents on the Hanford Site. The BAT determination is a key element in the DOE strategy to eliminate use of the soil column for contaminated effluents disposal. Following application of BAT, a liquid effluent is considered suitable for discharge to the environment, including the soil column. Liquid effluents on the Hanford Site are currently disposed of in accordance with DOE orders that require protection of public health and safety, and to the extent possible, minimize adverse impacts on the environment. The determination of BAT on a liquid effluent will only occur after the effluent meets all applicable release limits. As a result, the application of BAT may involve an additional level of control, as well as contribute to the overall Hanford Site as low as reasonably achievable (ALARA) program. 27 refs., 7 figs., 1 tab

Program prioritization system user requirements document for Gas Cooled Reactor Associates

International Nuclear Information System (INIS)

1981-01-01

Efficient management of the national HTGR program requires the establishment of an information system that will facilitate a more rational allocation of resources and task prioritization consistent with program policies. The system described in this document provides a data analysis mechanism for processing top level summary status and planning information in a rapid, timely and selective manner. Data produced by the system can be used by management to provide a rational basis for prioritizing tasks, evaluating program changes and program planning regarding costs, schedules and overall program development logic. The purpose of this document is to delineate the program prioritization system (PPS) requirements for use as a guide to acquiring and implementing the system

Health Service use of ionising radiations: Guidance

International Nuclear Information System (INIS)

1995-01-01

This booklet gives outline guidance on the use of ionising radiations in the Health Service in the United Kingdom. Extensive reference is made to documents where more detailed information may be found. The guidance covers general advice on the medical use of ionising radiations, statutory requirements, and guidance on selected Health Service issues such as patient identification procedures, information management systems, deviations from prescribed radiation dose, imaging and radiotherapy. (57 references) (U.K.)

European Society of Clinical Microbiology and Infectious Diseases: update of the treatment guidance document for Clostridium difficile infection.

Science.gov (United States)

Debast, S B; Bauer, M P; Kuijper, E J

2014-03-01

In 2009 the first European Society of Clinical Microbiology and Infection (ESCMID) treatment guidance document for Clostridium difficile infection (CDI) was published. The guideline has been applied widely in clinical practice. In this document an update and review on the comparative effectiveness of the currently available treatment modalities of CDI is given, thereby providing evidence-based recommendations on this issue. A computerized literature search was carried out to investigate randomized and non-randomized trials investigating the effect of an intervention on the clinical outcome of CDI. The Grades of Recommendation Assessment, Development and Evaluation (GRADE) system was used to grade the strength of our recommendations and the quality of the evidence. The ESCMID and an international team of experts from 11 European countries supported the process. To improve clinical guidance in the treatment of CDI, recommendations are specified for various patient groups, e.g. initial non-severe disease, severe CDI, first recurrence or risk for recurrent disease, multiple recurrences and treatment of CDI when oral administration is not possible. Treatment options that are reviewed include: antibiotics, toxin-binding resins and polymers, immunotherapy, probiotics, and faecal or bacterial intestinal transplantation. Except for very mild CDI that is clearly induced by antibiotic usage antibiotic treatment is advised. The main antibiotics that are recommended are metronidazole, vancomycin and fidaxomicin. Faecal transplantation is strongly recommended for multiple recurrent CDI. In case of perforation of the colon and/or systemic inflammation and deteriorating clinical condition despite antibiotic therapy, total abdominal colectomy or diverting loop ileostomy combined with colonic lavage is recommended. © 2013 The Authors Clinical Microbiology and Infection © 2013 European Society of Clinical Microbiology and Infectious Diseases.

New Department of Energy policy and guidance for cost-effectiveness in nuclear materials control and accountability programs

International Nuclear Information System (INIS)

Van Ryn, G.L.; Zack, N.R.

1994-01-01

Recent Department of Energy (DOE) initiatives have given Departmental nuclear facilities the opportunity to take more credit for certain existing safeguards and security systems in determining operational program protection requirements. New policies and guidance are coupled with these initiatives to enhance systems performance in a cost effective and efficient manner as well as to reduce operational costs. The application of these methods and technologies support safety, the reduction of personnel radiation exposure, emergency planning, and inspections by international teams. This discussion will review guidance and policies that support advanced systems and programs to decrease lifetime operational costs without increasing risk

Consideration of health inequalities in systematic reviews: a mapping review of guidance.

Science.gov (United States)

Maden, Michelle

2016-11-28

Given that we know that interventions shown to be effective in improving the health of a population may actually widen the health inequalities gap while others reduce it, it is imperative that all systematic reviewers consider how the findings of their reviews may impact (reduce or increase) on the health inequality gap. This study reviewed existing guidance on incorporating considerations of health inequalities in systematic reviews in order to examine the extent to which they can help reviewers to incorporate such issues. A mapping review was undertaken to identify guidance documents that purported to inform reviewers on whether and how to incorporate considerations of health inequalities. Searches were undertaken in Medline, CINAHL and The Cochrane Library Methodology Register. Review guidance manuals prepared by international organisations engaged in undertaking systematic reviews, and their associated websites were scanned. Studies were included if they provided an overview or discussed the development and testing of guidance for dealing with the incorporation of considerations of health inequalities in evidence synthesis. Results are summarised in narrative and tabular forms. Twenty guidance documents published between 2009 and 2016 were included. Guidance has been produced to inform considerations of health inequalities at different stages of the systematic review process. The Campbell and Cochrane Equity Group have been instrumental in developing and promoting such guidance. Definitions of health inequalities and guidance differed across the included studies. All but one guidance document were transparent in their method of production. Formal methods of evaluation were reported for six guidance documents. Most of the guidance was operationalised in the form of examples taken from published systematic reviews. The number of guidance items to operationalise ranges from 3 up to 26 with a considerable overlap noted. Adhering to the guidance will require more

75 FR 35510 - License Renewal Interim Staff Guidance Process, Revision 2 Notice of Availability

Science.gov (United States)

2010-06-22

... Related Regulatory Functions.'' An electronic copy of the revised LR-ISG process is available in the NRC's Agencywide Documents Access and Management System (ADAMS) under Accession No. ML100920158. The revised LR-ISG... interim changes to certain NRC license renewal guidance documents. These guidance documents facilitate the...

77 FR 16123 - Draft Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls...

Science.gov (United States)

2012-03-19

... Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document... Drug Administration 21 CFR Part 866 Draft Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document: Nucleic Acid-Based In Vitro Diagnostic Devices for the...

CANDU severe accident management guidance update

International Nuclear Information System (INIS)

Jones, L.; Popov, N.; Gilbert, L.; Weed, J.

2014-01-01

The CANDU Owners Group (COG) developed a set of generic and initial station-specific Severe Accident Management Guidance (SAMG) documents to mitigate the consequences to the public in the event of a severe accident. The generic portion of the COG SAMG was completed in 2006; the overall project including the station-specific phase was completed in April 2007. Over the years, the CANDU industry and utilities have continuously increased the knowledge base for SAMG and have incorporated various engineered features based on the knowledge obtained. As a result of the event that occurred at the Fukushima Daiiachi nuclear power plant (NPP) in Japan, the Canadian Nuclear Safety Commission (CNSC) established the CNSC Fukushima Task Force. The results of the task force were documented in INFO-0828, CNSC Staff Action Plan on the CNSC Fukushima Task Force Recommendations. Among the recommendation documented in INFO-828 were Fukushima Action Items (FAIs) directed towards the CANDU utilities in Canada; a portion of which are related to SAMG documentation updates and directed at enhancing SAM response. A COG joint project was established to support the closure of the CNSC FAIs and to revise the current CANDU documentation accordingly. This paper provides a high level summary of the COG project scope and results. It also demonstrates that the CANDU SAMG programs in Canada provide robust protection and mitigation of severe accidents. (author)

CANDU severe accident management guidance update

Energy Technology Data Exchange (ETDEWEB)

Jones, L., E-mail: lisa.m.jones@opg.com [Ontario Power Generation, Pickering, ON (Canada); Popov, N., E-mail: nik.popov@rogers.com [Candu Owners Group, Toronto, ON (Canada); Gilbert, L., E-mail: lovell.gilbert@brucepower.com [Bruce Power, Tiverton, ON (Canada); Weed, J., E-mail: jeff.weed@candu.gov [Candu Owners Group, Toronto, ON (Canada)

2014-07-01

The CANDU Owners Group (COG) developed a set of generic and initial station-specific Severe Accident Management Guidance (SAMG) documents to mitigate the consequences to the public in the event of a severe accident. The generic portion of the COG SAMG was completed in 2006; the overall project including the station-specific phase was completed in April 2007. Over the years, the CANDU industry and utilities have continuously increased the knowledge base for SAMG and have incorporated various engineered features based on the knowledge obtained. As a result of the event that occurred at the Fukushima Daiiachi nuclear power plant (NPP) in Japan, the Canadian Nuclear Safety Commission (CNSC) established the CNSC Fukushima Task Force. The results of the task force were documented in INFO-0828, CNSC Staff Action Plan on the CNSC Fukushima Task Force Recommendations. Among the recommendation documented in INFO-828 were Fukushima Action Items (FAIs) directed towards the CANDU utilities in Canada; a portion of which are related to SAMG documentation updates and directed at enhancing SAM response. A COG joint project was established to support the closure of the CNSC FAIs and to revise the current CANDU documentation accordingly. This paper provides a high level summary of the COG project scope and results. It also demonstrates that the CANDU SAMG programs in Canada provide robust protection and mitigation of severe accidents. (author)

78 FR 18353 - Guidance for Industry: Blood Establishment Computer System Validation in the User's Facility...

Science.gov (United States)

2013-03-26

... SUPPLEMENTARY INFORMATION section for electronic access to the guidance document. Submit electronic comments on... document entitled ``Guidance for Industry: Blood Establishment Computer System Validation in the User's... document to http://www.regulations.gov or written comments to the Division of Dockets Management (see...

75 FR 22813 - Guidance for Industry: Requalification Method for Reentry of Blood Donors Deferred Because of...

Science.gov (United States)

2010-04-30

...] Guidance for Industry: Requalification Method for Reentry of Blood Donors Deferred Because of Reactive Test... availability of a document entitled ``Guidance for Industry: Requalification Method for Reentry of Blood Donors... document entitled ``Guidance for Industry: Requalification Method for Reentry of Blood Donors Deferred...

Fossil energy program. Summary document

Energy Technology Data Exchange (ETDEWEB)

None

1980-05-01

This program summary document presents a comprehensive overview of the research, development, and demonstration (RD and D) activities that will be performed in FY 1981 by the Assistant Secretary for Fossil Energy (ASFE), US Department of Energy (DOE). The ASFE technology programs for the fossil resources of coal, petroleum (including oil shale) and gas have been established with the goal of making substantive contributions to the nation's future supply and efficienty use of energy. On April 29, 1977, the Administration submitted to Congress the National Energy Plan (NEP) and accompanying legislative proposals designed to establish a coherent energy policy structure for the United States. Congress passed the National Energy Act (NEA) on October 15, 1978, which allows implementation of the vital parts of the NEP. The NEP was supplemented by additional energy policy statements culminating in the President's address on July 15, 1979, presenting a program to further reduce dependence on imported petroleum. The passage of the NEA-related energy programs represent specific steps by the Administration and Congress to reorganize, redirect, and clarify the role of the Federal Government in the formulation and execution of national energy policy and programs. The energy technology RD and D prog4rams carried out by ASFE are an important part of the Federal Government's effort to provide the combination and amounts of energy resources needed to ensure national security and continued economic growth.

Guidance on enforcement of the requirements of the surface water treatment rule

International Nuclear Information System (INIS)

1992-06-01

The document provides guidance on several specific issues relating to the enforcement of the Surface Water Treatment Rule. The guidance deals with the provisions of the Rule relating to unfiltered systems. Enforcements of the requirements relating to the filtered systems will be dealt with in a later document

Quality Assurance Guidance for the Collection of Meteorological Data Using Passive Radiometers

Science.gov (United States)

This document augments the February 2000 guidance entitled Meteorological Monitoring Guidance for Regulatory Modeling Applications and the March 2008 guidance entitled Quality Assurance Handbook for Air Pollution Measurement Systems Volume IV: Meteorological Measurements Version ...

ADM guidance-Ceramics: guidance to the use of fractography in failure analysis of brittle materials.

Science.gov (United States)

Scherrer, Susanne S; Lohbauer, Ulrich; Della Bona, Alvaro; Vichi, Alessandro; Tholey, Michael J; Kelly, J Robert; van Noort, Richard; Cesar, Paulo Francisco

2017-06-01

To provide background information and guidance as to how to use fractography accurately, a powerful tool for failure analysis of dental ceramic structures. An extended palette of qualitative and quantitative fractography is provided, both for in vivo and in vitro fracture surface analyses. As visual support, this guidance document will provide micrographs of typical critical ceramic processing flaws, differentiating between pre- versus post sintering cracks, grinding damage related failures and occlusal contact wear origins and of failures due to surface degradation. The documentation emphasizes good labeling of crack features, precise indication of the direction of crack propagation (dcp), identification of the fracture origin, the use of fractographic photomontage of critical flaws or flaw labeling on strength data graphics. A compilation of recommendations for specific applications of fractography in Dentistry is also provided. This guidance document will contribute to a more accurate use of fractography and help researchers to better identify, describe and understand the causes of failure, for both clinical and laboratory-scale situations. If adequately performed at a large scale, fractography will assist in optimizing the methods of processing and designing of restorative materials and components. Clinical failures may be better understood and consequently reduced by sending out the correct message regarding the fracture origin in clinical trials. Copyright © 2017 The Academy of Dental Materials. All rights reserved.

75 FR 38343 - High-Speed Intercity Passenger Rail (HSIPR) Program

Science.gov (United States)

2010-07-01

... notice. The initial draft of this pending guidance document will be open for public comment, and FRA will... Development Program Budget and Schedule Form is a Microsoft Excel document that supports the qualitative and...-defined reporting relationships, statements of functional responsibilities, job descriptions, and job...

Report 3: Guidance document on practices to model and implement Extreme Weather hazards in extended PSA

International Nuclear Information System (INIS)

Alzbutas, R.; Ostapchuk, S.; Borysiewicz, M.; Decker, K.; Kumar, Manorma; Haeggstroem, A.; Nitoi, M.; Groudev, P.; Parey, S.; Potempski, S.; Raimond, E.; Siklossy, T.

2016-01-01

The goal of this report is to provide guidance on practices to model Extreme Weather hazards and implement them in extended level 1 PSA. This report is a joint deliverable of work package 21 (WP21) and work package 22 (WP22). The general objective of WP21 is to provide guidance on all of the individual hazards selected at the End Users Workshop. This guidance is focusing on extreme weather hazards, namely: extreme wind, extreme temperature and snow pack. Other hazards, however, are considered in cases where they are correlated/ associated with the hazard under discussion. Guidance developed refers to existing guidance whenever possible. As it was recommended by end users this guidance covers questions of developing integrated and/or separated extreme weathers PSA models. (authors)

Technical Basis Document for PFP Area Monitoring Dosimetry Program

CERN Document Server

Cooper, J R

2000-01-01

This document describes the phantom dosimetry used for the PFP Area Monitoring program and establishes the basis for the Plutonium Finishing Plant's (PFP) area monitoring dosimetry program in accordance with the following requirements: Title 10, Code of Federal Regulations (CFR), part 835, ''Occupational Radiation Protection'' Part 835.403; Hanford Site Radiological Control Manual (HSRCM-1), Part 514; HNF-PRO-382, Area Dosimetry Program; and PNL-MA-842, Hanford External Dosimetry Technical Basis Manual.

Technical Basis Document for PFP Area Monitoring Dosimetry Program

International Nuclear Information System (INIS)

COOPER, J.R.

2000-01-01

This document describes the phantom dosimetry used for the PFP Area Monitoring program and establishes the basis for the Plutonium Finishing Plant's (PFP) area monitoring dosimetry program in accordance with the following requirements: Title 10, Code of Federal Regulations (CFR), part 835, ''Occupational Radiation Protection'' Part 835.403; Hanford Site Radiological Control Manual (HSRCM-1), Part 514; HNF-PRO-382, Area Dosimetry Program; and PNL-MA-842, Hanford External Dosimetry Technical Basis Manual

Windows Calorimeter Control (WinCal) program computer software design description

International Nuclear Information System (INIS)

Pertzborn, N.F.

1997-01-01

The Windows Calorimeter Control (WinCal) Program System Design Description contains a discussion of the design details for the WinCal product. Information in this document will assist a developer in maintaining the WinCal system. The content of this document follows the guidance in WHC-CM-3-10, Software Engineering Standards, Standard for Software User Documentation

Water chemistry guidance in nuclear power plants in Japan

International Nuclear Information System (INIS)

Uchida, Shunsuke; Okada, Hidetoshi; Suzuki, Hiroaki; Naitoh, Masanori

2012-01-01

Water chemistry plays important roles in safe and reliable plant operation which are very critical for future power rate increases as well as aging plant management. Water chemistry control is required to satisfy the need for improved integrity of target materials, and at the same time it must be optimal for all materials and systems in a plant. Optimal water chemistry can be maintained by expert engineers who are knowledgeable about plant water chemistry, who have sufficient experience with plant operation, and whose knowledge is based on fundamental technologies. One of the latest subjects in the field of water chemistry is achieving suitable technical transfers, in which the achievements and experience with plant water chemistry accumulated by experts are successfully transferred to the next generation of engineers. For this purpose, documents on experience with water chemistry are being compiled as the guidance for water chemistry control and water chemistry standards, e.g., standards for chemical analysis procedures and guidance for water chemistry control procedures. This paper introduces the latest activities in Japan in establishing water chemistry guidance involving water chemistry standards, guidance documents and their supporting documents. (orig.)

FDA (Food and Drug Administration) compliance program guidance manual and updates (FY 86). Section 4. Medical and radiological devices. Irregular report

International Nuclear Information System (INIS)

1986-01-01

The FDA Compliance Program Guidance Manual provides a system for issuing and filing program plans and instructions directed to Food and Drug Administration Field operations for project implementation. Section IV provides those chapters of the Compliance Program Guidance Manual which pertain to the areas of medical and radiological devices. Some of the areas of coverage include laser and sunlamp standards inspections, compliance testing of various radiation-emitting products such as television receivers and microwave ovens, emergency response planning and policy, premarket approval and device manufacturers inspections, device problem reporting, sterilization of devices, and consumer education programs on medical and radiological devices

The LawsAndFamilies questionnaire on legal family formats for same-sex and/or different-sex couples : Text of the questions and of the accompanying guidance document.

NARCIS (Netherlands)

Waaldijk, C.; Lorenzo, Villaverde J.M.; Nikolina, N.; Zago, G.

2016-01-01

This Working Paper of the research project FamiliesAndSocieties contains the text of the LawsAndFamilies questionnaire, plus the text of the guidance document provided to legal experts answering this questionnaire. These texts are preceded by a brief introduction to the background, aims and

Technical Basis Document for PFP Area Monitoring Dosimetry Program

Energy Technology Data Exchange (ETDEWEB)

COOPER, J.R.

2000-04-17

This document describes the phantom dosimetry used for the PFP Area Monitoring program and establishes the basis for the Plutonium Finishing Plant's (PFP) area monitoring dosimetry program in accordance with the following requirements: Title 10, Code of Federal Regulations (CFR), part 835, ''Occupational Radiation Protection'' Part 835.403; Hanford Site Radiological Control Manual (HSRCM-1), Part 514; HNF-PRO-382, Area Dosimetry Program; and PNL-MA-842, Hanford External Dosimetry Technical Basis Manual.

Surplus Highly Enriched Uranium Disposition Program plan

International Nuclear Information System (INIS)

1996-10-01

The purpose of this document is to provide upper level guidance for the program that will downblend surplus highly enriched uranium for use as commercial nuclear reactor fuel or low-level radioactive waste. The intent of this document is to outline the overall mission and program objectives. The document is also intended to provide a general basis for integration of disposition efforts among all applicable sites. This plan provides background information, establishes the scope of disposition activities, provides an approach to the mission and objectives, identifies programmatic assumptions, defines major roles, provides summary level schedules and milestones, and addresses budget requirements

How does one develop the right quality assurance program for waste management projects?

International Nuclear Information System (INIS)

Hedges, D.

1988-01-01

The quality assurance requirements in use today for radioactive waste facilities, geologic repositories and hazardous waste projects were developed initially for the nuclear power plant industry, and their intent is being applied to regulations and guidance documents to radioactive and hazardous waste programs. The wording of the Nuclear Regulatory Commission (NRC) quality assurance (QA) requirements in Appendix B of 10CFR50, the related guidance documents and the industry's ANSI/ASME NQA-1 were developed over a period of several years to address quality assurance for the design and construction of the complex and interactive systems to produce electrical power using nuclear fuel. Now, those same documents are the basis for the quality assurance requirements and guidance for waste management facilities and repositories. The intent of Appendix B of 10CFR50 and NQA-1 can easily be applied to waste projects providing one understands and uses the intent of the requirements. This paper describes the intent of existing QA requirements as they apply to radioactive and hazardous waste programs. Methods of ensuring that the quality assurance program design will be acceptable to DOE and regulatory agencies are illustrated

How does one develop the right quality assurance program for waste management projects?

International Nuclear Information System (INIS)

Hedges, D.

1988-01-01

The quality assurance requirements in use today for radioactive waste facilities, geologic repositories and hazardous waste projects were developed initially for the nuclear power plant industry, and their intent is being applied by regulations and guidance documents to radioactive and hazardous waste programs. The wording of the NRC quality assurance requirements in Appendix B of 10CFR50, the related guidance documents and the industry's ANSI/ASME NQA-1 were developed over a period of several years to address quality assurance for the design and construction of the complex and interactive systems to produce electrical power using nuclear fuel. Now, those same documents are the basis for the quality assurance requirements and guidance for waste management facilities and repositories. The intent of Appendix B of 10CFR50 and NQA-1 can easily be applied to waste projects, providing one understands and uses the intent of the requirements. This paper describes the intent of existing QA requirements as they apply to radioactive and hazardous waste programs. Methods of ensuring that the quality assurance program design will be acceptable to DOE and regulatory agencies are illustrated

Tank waste remediation system privatization infrastructure program requirements and document management process guide

International Nuclear Information System (INIS)

ROOT, R.W.

1999-01-01

This guide provides the Tank Waste Remediation System Privatization Infrastructure Program management with processes and requirements to appropriately control information and documents in accordance with the Tank Waste Remediation System Configuration Management Plan (Vann 1998b). This includes documents and information created by the program, as well as non-program generated materials submitted to the project. It provides appropriate approval/control, distribution and filing systems

Dosimetric Significance of the ICRP's Updated Guidance and Models, 1989-2003, and Implications for U.S. Federal Guidance

Energy Technology Data Exchange (ETDEWEB)

Leggett, R.W.

2003-09-10

Over the past two decades the U.S. Environmental Protection Agency (EPA) has issued a series of Federal guidance documents for the purpose of providing the Federal and State agencies with technical information to assist their implementation of radiation protection programs. Currently recommended dose conversion factors, annual limits on intake, and derived air concentrations for intake of radionuclides are tabulated in Federal Guidance Report No. 11 (FGR 11), published in 1988. The tabulations in FGR 11 were based on dosimetric quantities and biokinetic and dosimetric models of the International Commission on Radiological Protection (ICRP) developed for application to occupational exposures. Since the publication of FGR 11 the ICRP has revised some of its dosimetric quantities and its models for workers and has also developed age-specific models and dose conversion factors for intake of radionuclides by members of the public. This report examines the extent of the changes in the inhalation and ingestion dose coefficients of FGR 11 implied by the updated recommendations of the ICRP, both for workers and members of the public.

Sandia Software Guidelines, Volume 2. Documentation

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This volume is one in a series of Sandia Software Guidelines intended for use in producing quality software within Sandia National Laboratories. In consonance with the IEEE Standards for software documentation, this volume provides guidance in the selection of an adequate document set for a software project and example formats for many types of software documentation. A tutorial on life cycle documentation is also provided. Extended document thematic outlines and working examples of software documents are available on electronic media as an extension of this volume.

PIV Logon Configuration Guidance

Energy Technology Data Exchange (ETDEWEB)

Lee, Glen Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-03-04

This document details the configurations and enhancements implemented to support the usage of federal Personal Identity Verification (PIV) Card for logon on unclassified networks. The guidance is a reference implementation of the configurations and enhancements deployed at the Los Alamos National Laboratory (LANL) by Network and Infrastructure Engineering – Core Services (NIE-CS).

Campus Partnerships Improve Impact Documentation of Nutrition Programs

Science.gov (United States)

Brinkman, Patricia

2015-01-01

Partnerships with other campus college units can provide ways of improving Extension's impact documentation. Nutrition programs have relied upon knowledge gained and people's self report of behavior change. Partnering with the College of Nursing, student nurses provided blood screenings during the pre and 6 month follow-up of a pilot heart risk…

Data requirement comparison between the fixed site upgrade rule guidance compendium and the Structured Assessment Approach Licensee Submittal Document

Energy Technology Data Exchange (ETDEWEB)

Parziale, A.A.; Sacks, I.J.

1980-12-01

We compared the Structured Assessment Approach's (SAA) Licensee Submittal Document (LSD) with the Fixed Site Physical Protection Upgrade Rule Guidance Compendium Standard Format and Content (SFC) Guide using correlation matrices to see how well the data requirements of the SFC Guide coincided with those of a specific automated vulnerability assessment technique for fixed-site nuclear fuel cycle facilities, namely, SAA. We found that a limited SAA assessment is possible using the SFC Guide, but significant and critical safeguards vulnerabilities might be missed. Also, it was found that in some cases the organization and format of the SFC Guide input data and information made the preparation of data for the SAA somewhat awkward. 2 refs., 2 tabs.

76 FR 60937 - Draft License Renewal Interim Staff Guidance LR-ISG-2011-02; Aging Management Program for Steam...

Science.gov (United States)

2011-09-30

...-2011-02; Aging Management Program for Steam Generators AGENCY: Nuclear Regulatory Commission. ACTION... License Renewal Interim Staff Guidance (LR-ISG), LR-ISG-2011-02, ``Aging Management Program for Steam... using Revision 3 of NEI 97-06 to manage steam generator aging. The Draft LR-ISG revises the NRC staff's...

78 FR 52203 - Guidance for Industry on Compliance With Regulations Restricting the Sale and Distribution of...

Science.gov (United States)

2013-08-22

... guidance document consistent with FDA's good guidance practices regulation (21 CFR 10.115). The guidance...] Guidance for Industry on Compliance With Regulations Restricting the Sale and Distribution of Cigarettes... Distribution of Cigarettes and Smokeless Tobacco to Protect Children and Adolescents.'' This guidance is...

Overview of Evaluation Methods for R&D Programs. A Directory of Evaluation Methods Relevant to Technology Development Programs

Energy Technology Data Exchange (ETDEWEB)

Ruegg, Rosalie [TIA Consulting, Inc., Emeral Isle, NC (United States); Jordan, Gretchen B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2007-03-01

This document provides guidance for evaluators who conduct impact assessments to determine the “realized” economic benefits and costs, energy, environmental benefits, and other impacts of the Office of Energy Efficiency and Renewable Energy’s (EERE) R&D programs. The focus of this Guide is on realized outcomes or impacts of R&D programs actually experienced by American citizens, industry, and others.

High-level waste storage tank farms/242-A evaporator standards/requirements identification document (S/RID), Vol. 2

International Nuclear Information System (INIS)

1994-04-01

The Quality Assurance Functional Area Requirements Identification Document (RID), addresses the programmatic requirements that ensure risks and environmental impacts are minimized, ensure safety, reliability, and performance are maximized through the application of effective management systems commensurate with the risks posed by the Tank Farm Facility and its operation. This RID incorporates guidance intended to provide Tank Farms management with the necessary requirements information to develop, upgrade, or assess the effectiveness of a Quality Assurance Program in the performance of organizational and functional activities. Quality Assurance is defined as all those planned and systematic actions necessary to provide adequate confidence that a facility, structure, system, or component will perform satisfactorily and safely in service. This document will provide the specific requirements to meet DNFSB recommendations and the guidance provided in DOE Order 5700.6C, utilizing industry codes, standards, regulatory guidelines, and industry good practices that have proven to be essential elements for an effective and efficient Quality Assurance Program as the nuclear industry has matured over the last thirty years

High-level waste storage tank farms/242-A evaporator standards/requirements identification document (S/RID), Vol. 2

Energy Technology Data Exchange (ETDEWEB)

1994-04-01

The Quality Assurance Functional Area Requirements Identification Document (RID), addresses the programmatic requirements that ensure risks and environmental impacts are minimized, ensure safety, reliability, and performance are maximized through the application of effective management systems commensurate with the risks posed by the Tank Farm Facility and its operation. This RID incorporates guidance intended to provide Tank Farms management with the necessary requirements information to develop, upgrade, or assess the effectiveness of a Quality Assurance Program in the performance of organizational and functional activities. Quality Assurance is defined as all those planned and systematic actions necessary to provide adequate confidence that a facility, structure, system, or component will perform satisfactorily and safely in service. This document will provide the specific requirements to meet DNFSB recommendations and the guidance provided in DOE Order 5700.6C, utilizing industry codes, standards, regulatory guidelines, and industry good practices that have proven to be essential elements for an effective and efficient Quality Assurance Program as the nuclear industry has matured over the last thirty years.

BENCHPAR PROJECT. How to Incorporate ThermaI-Hydro-Mechanical Coupled Processes into Performance Assessments and Design Studies for Radioactive Waste Disposal in Geological Formations. Guidance Document

International Nuclear Information System (INIS)

Stephansson, O.; Andersson, Johan

2005-02-01

The objective of this Guidance Document is to provide advice on how to incorporate thermo-hydro-mechanical (THM) coupled processes into Performance Assessments (PAS) and design studies for radioactive waste disposal in geological formations to be experienced in a European context. The document has been generated by the EU research project BENCHPAR: Benchmark Tests and Guidance on Coupled Processes for Performance Assessment of Nuclear Waste Repositories. The document starts in Section 1 with an explanation of why numerical analyses incorporating THM mechanisms are required for radioactive waste studies and provides background material on the subject. Then, the THM processes and their interactions are explained in Section 2. Three case examples of THM numerical analysis are presented in Section 3 to illustrate the type of work that can be conducted to study the near-field, upscaling, and the far-field. For the three cases, there is discussion on the main findings, the relevance to a safety case, the relative importance of the different couplings, and the uncertainties involved. The importance and priority of the THM couplings are then summarized in Section 4. It is especially important to be able to technically audit the numerical analyses in order to establish that all the relevant variables, parameters and mechanisms have been included in the modelling and hence that the numerical model adequately represents the rock and engineering reality. Accordingly, recommended soft and hard auditing procedures are presented in Section 5. In this Guidance Document, we emphasize especially that the most important step in numerical modelling is not executing the calculations per se, but the earlier conceptualization of the problem regarding the dominant processes, the material properties and parameters, the engineering perturbations, and their mathematical presentations. The associated modelling component of addressing the uncertainties and estimating their influence on the

Virtual Ultrasound Guidance for Inexperienced Operators

Science.gov (United States)

Caine, Timothy; Martin, David

2012-01-01

Medical ultrasound or echocardiographic studies are highly operator-dependent and generally require lengthy training and internship to perfect. To obtain quality echocardiographic images in remote environments, such as on-orbit, remote guidance of studies has been employed. This technique involves minimal training for the user, coupled with remote guidance from an expert. When real-time communication or expert guidance is not available, a more autonomous system of guiding an inexperienced operator through an ultrasound study is needed. One example would be missions beyond low Earth orbit in which the time delay inherent with communication will make remote guidance impractical. The Virtual Ultrasound Guidance system is a combination of hardware and software. The hardware portion includes, but is not limited to, video glasses that allow hands-free, full-screen viewing. The glasses also allow the operator a substantial field of view below the glasses to view and operate the ultrasound system. The software is a comprehensive video program designed to guide an inexperienced operator through a detailed ultrasound or echocardiographic study without extensive training or guidance from the ground. The program contains a detailed description using video and audio to demonstrate equipment controls, ergonomics of scanning, study protocol, and scanning guidance, including recovery from sub-optimal images. The components used in the initial validation of the system include an Apple iPod Classic third-generation as the video source, and Myvue video glasses. Initially, the program prompts the operator to power-up the ultrasound and position the patient. The operator would put on the video glasses and attach them to the video source. After turning on both devices and the ultrasound system, the audio-video guidance would then instruct on patient positioning and scanning techniques. A detailed scanning protocol follows with descriptions and reference video of each view along with

75 FR 73107 - Guidance for Industry and Food and Drug Administration Staff; Blood Lancet Labeling; Availability

Science.gov (United States)

2010-11-29

...] Guidance for Industry and Food and Drug Administration Staff; Blood Lancet Labeling; Availability AGENCY... announcing the availability of the guidance entitled ``Guidance for Industry and Food and Drug Administration... single copies of the guidance document entitled ``Guidance for Industry and Food and Drug Administration...

78 FR 13069 - Draft Guidance for Industry: Recommendations for Screening, Testing, and, Management of Blood...

Science.gov (United States)

2013-02-26

... components, including Source Plasma. The guidance announced in this notice replaces the draft guidance... before it begins work on the final version of the guidance, submit either electronic or written comments... the SUPPLEMENTARY INFORMATION section for electronic access to the draft guidance document. Submit...

Defense transuranic waste program strategy document

International Nuclear Information System (INIS)

1982-07-01

This document summarizes the strategy for managing transuranic (TRU) wastes generated in defense and research activities regulated by the US Department of Energy. It supercedes a document issued in July 1980. In addition to showing how current strategies of the Defense Transuranic Waste Program (DTWP) are consistent with the national objective of isolating radioactive wastes from the biosphere, this document includes information about the activities of the Transuranic Lead Organization (TLO). To explain how the DTWP strategy is implemented, this document also discusses how the TLO coordinates and integrates the six separate elements of the DTWP: (1) Waste Generation Site Activities, (2) Storage Site Activities, (3) Burial Site Activities, (4) Technology Development, (5) Transportation Development, and (6) Permanent Disposal. Storage practices for TRU wastes do not pose short-term hazards to public health and safety or to the environment. Isolation of TRU wastes in a deep-mined geologic repository is considered the most promising of the waste disposal alternatives available. This assessment is supported by the DOE Record of Decision to proceed with research and development work at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico - a deep-mined geologic research and development project. In support of the WIPP research project and the permanent disposal of TRU waste, the DTWP strategy for the near term will concentrate on completion of procedures and the design and construction of all facilities necessary to certify newly-generated (NG) and stored TRU wastes for emplacement in the WIPP. In addition, the strategy involves evaluating alternatives for disposing of some transuranic wastes by methods which may allow for on-site disposal of these wastes and yet preserve adequate margins of safety to protect public health and the environment

Safety of magnetic fusion facilities: Guidance

International Nuclear Information System (INIS)

1996-05-01

This document provides guidance for the implementation of the requirements identified in DOE-STD-6002-96, Safety of Magnetic Fusion Facilities: Requirements. This guidance is intended for the managers, designers, operators, and other personnel with safety responsibilities for facilities designated as magnetic fusion facilities. While the requirements in DOE-STD-6002-96 are generally applicable to a wide range of fusion facilities, this Standard, DOE-STD-6003-96, is concerned mainly with the implementation of those requirements in large facilities such as the International Thermonuclear Experimental Reactor (ITER). Using a risk-based prioritization, the concepts presented here may also be applied to other magnetic fusion facilities. This Standard is oriented toward regulation in the Department of Energy (DOE) environment as opposed to regulation by other regulatory agencies. As the need for guidance involving other types of fusion facilities or other regulatory environments emerges, additional guidance volumes should be prepared. The concepts, processes, and recommendations set forth here are for guidance only. They will contribute to safety at magnetic fusion facilities

Instrument and Survey Analysis Technical Report: Program Implementation Survey. Technical Report #1112

Science.gov (United States)

Alonzo, Julie; Tindal, Gerald

2011-01-01

This technical document provides guidance to educators on the creation and interpretation of survey instruments, particularly as they relate to an analysis of program implementation. Illustrative examples are drawn from a survey of educators related to the use of the easyCBM learning system. This document includes specific sections on…

76 FR 9583 - Draft Guidance for Industry on Clinical Pharmacogenomics: Premarketing Evaluation in Early Phase...

Science.gov (United States)

2011-02-18

... final version of the guidance, submit either electronic or written comments on the draft guidance by... electronic access to the guidance document. Submit electronic comments on the draft guidance to http://www... body tissue or fluid (e.g., blood, plasma, cerebrospinal fluid). Drug response results from the...

Guidance document on practices to model and implement Earthquake hazards in extended PSA (final version). Volume 1

International Nuclear Information System (INIS)

Decker, K.; Hirata, K.; Groudev, P.

2016-01-01

The current report provides guidance for the assessment of seismo-tectonic hazards in level 1 and 2 PSA. The objective is to review existing guidance, identify methodological challenges, and to propose novel guidance on key issues. Guidance for the assessment of vibratory ground motion and fault capability comprises the following: - listings of data required for the hazard assessment and methods to estimate data quality and completeness; - in-depth discussion of key input parameters required for hazard models; - discussions on commonly applied hazard assessment methodologies; - references to recent advances of science and technology. Guidance on the assessment of correlated or coincident hazards comprises of chapters on: - screening of correlated hazards; - assessment of correlated hazards (natural and man-made); - assessment of coincident hazards. (authors)

ANS severe accident program overview & planning document

Energy Technology Data Exchange (ETDEWEB)

Taleyarkhan, R.P.

1995-09-01

The Advanced Neutron Source (ANS) severe accident document was developed to provide a concise and coherent mechanism for presenting the ANS SAP goals, a strategy satisfying these goals, a succinct summary of the work done to date, and what needs to be done in the future to ensure timely licensability. Guidance was received from various bodies [viz., panel members of the ANS severe accident workshop and safety review committee, Department of Energy (DOE) orders, Nuclear Regulatory Commission (NRC) requirements for ALWRs and advanced reactors, ACRS comments, world-wide trends] were utilized to set up the ANS-relevant SAS goals and strategy. An in-containment worker protection goal was also set up to account for the routine experimenters and other workers within containment. The strategy for achieving the goals is centered upon closing the severe accident issues that have the potential for becoming certification issues when assessed against realistic bounding events. Realistic bounding events are defined as events with an occurrency frequency greater than 10{sup {minus}6}/y. Currently, based upon the level-1 probabilistic risk assessment studies, the realistic bounding events for application for issue closure are flow blockage of fuel element coolant channels, and rapid depressurization-related accidents.

Standard Review Plan Update and Development Program

International Nuclear Information System (INIS)

1992-05-01

This implementing procedures document (IPD) was prepared for use in implementing tasks under the standard review plan update and development program (SRP-UDP). The IPD provides comprehensive guidance and detailed procedures for SRP-UDP tasks. The IPD is mandatory for contractors performing work for the SRP-UDP. It is guidance for the staff. At the completion of the SRP-UDP, the IPD will be revised (to remove the UDP aspects) and will replace NRR Office Letter No. 800 as long-term maintenance procedures

Standard Review Plan Update and Development Program

Energy Technology Data Exchange (ETDEWEB)

1992-05-01

This implementing procedures document (IPD) was prepared for use in implementing tasks under the standard review plan update and development program (SRP-UDP). The IPD provides comprehensive guidance and detailed procedures for SRP-UDP tasks. The IPD is mandatory for contractors performing work for the SRP-UDP. It is guidance for the staff. At the completion of the SRP-UDP, the IPD will be revised (to remove the UDP aspects) and will replace NRR Office Letter No. 800 as long-term maintenance procedures.

ACHP | Federal Emergency Management Agency Historic Preservation Program

Science.gov (United States)

/ehp/hp/fema386-6.shtm FEMA's Historic Preservation Policies and Guidance: http://www.fema.gov /environmental-planning-and-historic-preservation-program/femas-historic-preservation-policies Homeowner Flood Insurance Affordability Act: http://www.fema.gov/media-library/assets/documents/93074 Updated February 8

Scheme Program Documentation Tools

DEFF Research Database (Denmark)

Nørmark, Kurt

2004-01-01

are separate and intended for different documentation purposes they are related to each other in several ways. Both tools are based on XML languages for tool setup and for documentation authoring. In addition, both tools rely on the LAML framework which---in a systematic way---makes an XML language available...... as named functions in Scheme. Finally, the Scheme Elucidator is able to integrate SchemeDoc resources as part of an internal documentation resource....

Enhancing pediatric residents’ scholar role: the development of a Scholarly Activity Guidance and Evaluation program

Directory of Open Access Journals (Sweden)

Catherine M. Pound

2015-06-01

Full Text Available Background: Research training is essential to the development of well-rounded physicians. Although many pediatric residency programs require residents to complete a research project, it is often challenging to integrate research training into educational programs. Objective: We aimed to develop an innovative research program for pediatric residents, called the Scholarly Activity Guidance and Evaluation (SAGE program. Methods: We developed a competency-based program which establishes benchmarks for pediatric residents, while providing ongoing academic mentorship. Results: Feedback from residents and their research supervisors about the SAGE program has been positive. Preliminary evaluation data have shown that all final-year residents have met or exceeded program expectations. Conclusions: By providing residents with this supportive environment, we hope to influence their academic career paths, increase their research productivity, promote evidence-based practice, and ultimately, positively impact health outcomes.

SPAR-H Step-by-Step Guidance

Energy Technology Data Exchange (ETDEWEB)

April M. Whaley; Dana L. Kelly; Ronald L. Boring; William J. Galyean

2012-06-01

Step-by-step guidance was developed recently at Idaho National Laboratory for the US Nuclear Regulatory Commission on the use of the Standardized Plant Analysis Risk-Human Reliability Analysis (SPAR-H) method for quantifying Human Failure Events (HFEs). This work was done to address SPAR-H user needs, specifically requests for additional guidance on the proper application of various aspects of the methodology. This paper overviews the steps of the SPAR-H analysis process and highlights some of the most important insights gained during the development of the step-by-step directions. This supplemental guidance for analysts is applicable when plant-specific information is available, and goes beyond the general guidance provided in existing SPAR-H documentation. The steps highlighted in this paper are: Step-1, Categorizing the HFE as Diagnosis and/or Action; Step-2, Rate the Performance Shaping Factors; Step-3, Calculate PSF-Modified HEP; Step-4, Accounting for Dependence, and; Step-5, Minimum Value Cutoff.

Optimal guidance law in quantum mechanics

International Nuclear Information System (INIS)

Yang, Ciann-Dong; Cheng, Lieh-Lieh

2013-01-01

Following de Broglie’s idea of a pilot wave, this paper treats quantum mechanics as a problem of stochastic optimal guidance law design. The guidance scenario considered in the quantum world is that an electron is the flight vehicle to be guided and its accompanying pilot wave is the guidance law to be designed so as to guide the electron to a random target driven by the Wiener process, while minimizing a cost-to-go function. After solving the stochastic optimal guidance problem by differential dynamic programming, we point out that the optimal pilot wave guiding the particle’s motion is just the wavefunction Ψ(t,x), a solution to the Schrödinger equation; meanwhile, the closed-loop guidance system forms a complex state–space dynamics for Ψ(t,x), from which quantum operators emerge naturally. Quantum trajectories under the action of the optimal guidance law are solved and their statistical distribution is shown to coincide with the prediction of the probability density function Ψ ∗ Ψ. -- Highlights: •Treating quantum mechanics as a pursuit-evasion game. •Reveal an interesting analogy between guided flight motion and guided quantum motion. •Solve optimal quantum guidance problem by dynamic programming. •Gives a formal proof of de Broglie–Bohm’s idea of a pilot wave. •The optimal pilot wave is shown to be a wavefunction solved from Schrödinger equation

Optimal guidance law in quantum mechanics

Energy Technology Data Exchange (ETDEWEB)

Yang, Ciann-Dong, E-mail: cdyang@mail.ncku.edu.tw; Cheng, Lieh-Lieh, E-mail: leo8101@hotmail.com

2013-11-15

Following de Broglie’s idea of a pilot wave, this paper treats quantum mechanics as a problem of stochastic optimal guidance law design. The guidance scenario considered in the quantum world is that an electron is the flight vehicle to be guided and its accompanying pilot wave is the guidance law to be designed so as to guide the electron to a random target driven by the Wiener process, while minimizing a cost-to-go function. After solving the stochastic optimal guidance problem by differential dynamic programming, we point out that the optimal pilot wave guiding the particle’s motion is just the wavefunction Ψ(t,x), a solution to the Schrödinger equation; meanwhile, the closed-loop guidance system forms a complex state–space dynamics for Ψ(t,x), from which quantum operators emerge naturally. Quantum trajectories under the action of the optimal guidance law are solved and their statistical distribution is shown to coincide with the prediction of the probability density function Ψ{sup ∗}Ψ. -- Highlights: •Treating quantum mechanics as a pursuit-evasion game. •Reveal an interesting analogy between guided flight motion and guided quantum motion. •Solve optimal quantum guidance problem by dynamic programming. •Gives a formal proof of de Broglie–Bohm’s idea of a pilot wave. •The optimal pilot wave is shown to be a wavefunction solved from Schrödinger equation.

77 FR 20826 - Guidance for Industry and Food and Drug Administration Staff; Food and Drug Administration and...

Science.gov (United States)

2012-04-06

...] Guidance for Industry and Food and Drug Administration Staff; Food and Drug Administration and Industry... Administration (FDA) is announcing the availability of the guidance entitled ``Guidance for Industry and Food and... written requests for single copies of the guidance document entitled ``Guidance for Industry and Food and...

Asset Management Plans, Appraisal Guidance for 2003-04.

Science.gov (United States)

Department for Education and Skills, London (England).

This document is one in a series which aims to assist Local Authorities in Britain with asset management planning (AMPs) for schools. AMPs set out the information needed, and the criteria used, to make decisions about spending on school premises. The document provides guidance on the appraisal of school AMPs in 2002 to inform 3-year formulaic…

Deep Energy Retrofit Guidance for the Building America Solutions Center

Energy Technology Data Exchange (ETDEWEB)

Less, Brennan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Walker, Iain [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2015-01-01

The U.S. DOE Building America program has established a research agenda targeting market-relevant strategies to achieve 40% reductions in existing home energy use by 2030. Deep Energy Retrofits (DERs) are part of the strategy to meet and exceed this goal. DERs are projects that create new, valuable assets from existing residences, by bringing homes into alignment with the expectations of the 21st century. Ideally, high energy using, dated homes that are failing to provide adequate modern services to their owners and occupants (e.g., comfortable temperatures, acceptable humidity, clean, healthy), are transformed through comprehensive upgrades to the building envelope, services and miscellaneous loads into next generation high performance homes. These guidance documents provide information to aid in the broader market adoption of DERs. They are intended for inclusion in the online resource the Building America Solutions Center (BASC). This document is an assemblage of multiple entries in the BASC, each of which addresses a specific aspect of Deep Energy Retrofit best practices for projects targeting at least 50% energy reductions. The contents are based upon a review of actual DERs in the U.S., as well as a mixture of engineering judgment, published guidance from DOE research in technologies and DERs, simulations of cost-optimal DERs, Energy Star and Consortium for Energy Efficiency (CEE) product criteria, and energy codes.

Configuration management: Phase II implementation guidance

Energy Technology Data Exchange (ETDEWEB)

1994-03-01

Configuration management (CM) is essential to maintaining an acceptable level of risk to the public, workers, environment, or mission success. It is a set of activities and techniques used to maintain consistency among physical and functional configuration, applicable requirements, and key documents. This document provides guidance for continuing the implementation of CM in a phased and graded manner. It describes a cost-effective approach to documented consistency with requirements, with early emphasis on items most important to safety and environmental protection. It is intended to help responsible line managers and configuration management staff personnel in meeting the Energy Systems configuration management policy standard.

Guidance Manual for Conducting Screening Level Ecological Risk Assessments at the INEL

Energy Technology Data Exchange (ETDEWEB)

R. L. VanHorn; N. L. Hampton; R. C. Morris

1995-06-01

This document presents reference material for conducting screening level ecological risk assessments (SLERAs)for the waste area groups (WAGs) at the Idaho National Engineering Laboratory. Included in this document are discussions of the objectives of and processes for conducting SLERAs. The Environmental Protection Agency ecological risk assessment framework is closely followed. Guidance for site characterization, stressor characterization, ecological effects, pathways of contaminant migration, the conceptual site model, assessment endpoints, measurement endpoints, analysis guidance, and risk characterization are included.

ANS severe accident program overview ampersand planning document

International Nuclear Information System (INIS)

Taleyarkhan, R.P.

1995-09-01

The Advanced Neutron Source (ANS) severe accident document was developed to provide a concise and coherent mechanism for presenting the ANS SAP goals, a strategy satisfying these goals, a succinct summary of the work done to date, and what needs to be done in the future to ensure timely licensability. Guidance was received from various bodies [viz., panel members of the ANS severe accident workshop and safety review committee, Department of Energy (DOE) orders, Nuclear Regulatory Commission (NRC) requirements for ALWRs and advanced reactors, ACRS comments, world-wide trends] were utilized to set up the ANS-relevant SAS goals and strategy. An in-containment worker protection goal was also set up to account for the routine experimenters and other workers within containment. The strategy for achieving the goals is centered upon closing the severe accident issues that have the potential for becoming certification issues when assessed against realistic bounding events. Realistic bounding events are defined as events with an occurrency frequency greater than 10 -6 /y. Currently, based upon the level-1 probabilistic risk assessment studies, the realistic bounding events for application for issue closure are flow blockage of fuel element coolant channels, and rapid depressurization-related accidents

FY 1987 program summary document: Office of Defense Waste and Transportation Management

International Nuclear Information System (INIS)

1987-04-01

This document describes the Office of Defense Waste and Transportation Management (DWTM) Program as supported by the President's Fiscal Year (FY) 1987 Budget Request to Congress. It specifically addresses the program's organization, objectives, strategies, and plans for FY 1987

78 FR 39284 - Technical Guidance for Assessing Environmental Justice in Regulatory Analysis

Science.gov (United States)

2013-07-01

... ENVIRONMENTAL PROTECTION AGENCY [EPA-HQ-OA-2013-0320; FRL-9830-1] Technical Guidance for Assessing Environmental Justice in Regulatory Analysis AGENCY: Environmental Protection Agency (EPA). ACTION: Notice... Environmental Protection Agency (EPA) issued for public comment a document entitled, ``Technical Guidance for...

LLNL Waste Minimization Program Plan

International Nuclear Information System (INIS)

1990-01-01

This document is the February 14, 1990 version of the LLNL Waste Minimization Program Plan (WMPP). The Waste Minimization Policy field has undergone continuous changes since its formal inception in the 1984 HSWA legislation. The first LLNL WMPP, Revision A, is dated March 1985. A series of informal revision were made on approximately a semi-annual basis. This Revision 2 is the third formal issuance of the WMPP document. EPA has issued a proposed new policy statement on source reduction and recycling. This policy reflects a preventative strategy to reduce or eliminate the generation of environmentally-harmful pollutants which may be released to the air, land surface, water, or ground water. In accordance with this new policy new guidance to hazardous waste generators on the elements of a Waste Minimization Program was issued. In response to these policies, DOE has revised and issued implementation guidance for DOE Order 5400.1, Waste Minimization Plan and Waste Reduction reporting of DOE Hazardous, Radioactive, and Radioactive Mixed Wastes, final draft January 1990. This WMPP is formatted to meet the current DOE guidance outlines. The current WMPP will be revised to reflect all of these proposed changes when guidelines are established. Updates, changes and revisions to the overall LLNL WMPP will be made as appropriate to reflect ever-changing regulatory requirements. 3 figs., 4 tabs

Environmental guidance regulatory bulletin

International Nuclear Information System (INIS)

1997-01-01

This document describes the background on expanding public participation in the Resource Conservation and Recovery Act and DOE's response. The bulletin also describes the changes made by the final rule to existing regulations, guidance provided by EPA in the preamble and in the revised RCRA Public Participation Manual, the relationship between public participation and environmental justice, and DOE's recent public participation and environmental justice initiatives

Patient-reported outcome (PRO assessment in clinical trials: a systematic review of guidance for trial protocol writers.

Directory of Open Access Journals (Sweden)

Melanie Calvert

Full Text Available Evidence suggests there are inconsistencies in patient-reported outcome (PRO assessment and reporting in clinical trials, which may limit the use of these data to inform patient care. For trials with a PRO endpoint, routine inclusion of key PRO information in the protocol may help improve trial conduct and the reporting and appraisal of PRO results; however, it is currently unclear exactly what PRO-specific information should be included. The aim of this review was to summarize the current PRO-specific guidance for clinical trial protocol developers.We searched the MEDLINE, EMBASE, CINHAL and Cochrane Library databases (inception to February 2013 for PRO-specific guidance regarding trial protocol development. Further guidance documents were identified via Google, Google scholar, requests to members of the UK Clinical Research Collaboration registered clinical trials units and international experts. Two independent investigators undertook title/abstract screening, full text review and data extraction, with a third involved in the event of disagreement. 21,175 citations were screened and 54 met the inclusion criteria. Guidance documents were difficult to access: electronic database searches identified just 8 documents, with the remaining 46 sourced elsewhere (5 from citation tracking, 27 from hand searching, 7 from the grey literature review and 7 from experts. 162 unique PRO-specific protocol recommendations were extracted from included documents. A further 10 PRO recommendations were identified relating to supporting trial documentation. Only 5/162 (3% recommendations appeared in ≥50% of guidance documents reviewed, indicating a lack of consistency.PRO-specific protocol guidelines were difficult to access, lacked consistency and may be challenging to implement in practice. There is a need to develop easily accessible consensus-driven PRO protocol guidance. Guidance should be aimed at ensuring key PRO information is routinely included in

Data Management-Supplement to Section 106 Tribal Guidance

Science.gov (United States)

The document supplements the Tribal 106 Guidance by providing useful suggestions and tips to tribes about how to establish a data management system that reflects tribal water quality goals and objectives.

ADM guidance-Ceramics: all-ceramic multilayer interfaces in dentistry.

Science.gov (United States)

Lohbauer, Ulrich; Scherrer, Susanne S; Della Bona, Alvaro; Tholey, Michael; van Noort, Richard; Vichi, Alessandro; Kelly, J Robert; Cesar, Paulo F

2017-06-01

This guidance document describes the specific issues involved in dental multilayer ceramic systems. The material interactions with regard to specific thermal and mechanical properties are reviewed and the characteristics of dental tooth-shaped processing parameters (sintering, geometry, thickness ratio, etc.) are discussed. Several techniques for the measurement of bond quality and residual stresses are presented with a detailed discussion of advantages and disadvantages. In essence no single technique is able to describe adequately the all-ceramic interface. Invasive or semi-invasive methods have been shown to distort the information regarding the residual stress state while non-invasive methods are limited due to resolution, field of focus or working depth. This guidance document has endeavored to provide a scientific basis for future research aimed at characterizing the ceramic interface of dental restorations. Along with the methodological discussion it is seeking to provide an introduction and guidance to relatively inexperienced researchers. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Security in the transport of radioactive material - interim guidance for comment

International Nuclear Information System (INIS)

Legoux, P.; Wangler, M.

2004-01-01

While the IAEA has provided specific guidance for physical protection in the transport of nuclear material, its previous publications have only provided some general guidelines for security of non-nuclear radioactive material in transport. Some basic practical advice has been provided in the requirements of the International Basic Safety Standards for Protection against Ionising Radiation and for the Safety of Radiation Sources (BSS) [1]. These guidelines were primarily directed toward such issues as unintentional exposure to radiation, negligence and inadvertent loss. Recently, the IAEA published a document on the security of sources, which included some general guidance on providing security during transport of the sources. However, it is clear that more guidance is needed for security during the transport of radioactive material in addition to those already existing for nuclear material. Member States have requested guidance on the type and nature of security measures that might be put in place for radioactive material in general during its transport and on the methodology to be used in choosing and implementing such measures. The purpose of the TECDOC on Security in the Transport of Radioactive Material being developed by the IAEA is to provide an initial response to that request. This interim guidance is being developed with a view to harmonizing the security guidance - as much as possible - with existing guidance from the IAEA for the transport of radioactive sources and nuclear material. It is also intended to harmonize with model requirements developed in 2002-2003 by the United Nations Economic and Social Council's Committee of Experts on the Transport of Dangerous Goods and on the Globally Harmonised System of Classification and Labelling of Chemicals which was issued as general security guidelines for all dangerous goods, including radioactive material, and that will shortly be implemented as binding regulations by the international modal authorities

Security in the transport of radioactive material - interim guidance for comment

Energy Technology Data Exchange (ETDEWEB)

Legoux, P.; Wangler, M. [International Atomic Energy Agency, Vienna (Austria)

2004-07-01

While the IAEA has provided specific guidance for physical protection in the transport of nuclear material, its previous publications have only provided some general guidelines for security of non-nuclear radioactive material in transport. Some basic practical advice has been provided in the requirements of the International Basic Safety Standards for Protection against Ionising Radiation and for the Safety of Radiation Sources (BSS) [1]. These guidelines were primarily directed toward such issues as unintentional exposure to radiation, negligence and inadvertent loss. Recently, the IAEA published a document on the security of sources, which included some general guidance on providing security during transport of the sources. However, it is clear that more guidance is needed for security during the transport of radioactive material in addition to those already existing for nuclear material. Member States have requested guidance on the type and nature of security measures that might be put in place for radioactive material in general during its transport and on the methodology to be used in choosing and implementing such measures. The purpose of the TECDOC on Security in the Transport of Radioactive Material being developed by the IAEA is to provide an initial response to that request. This interim guidance is being developed with a view to harmonizing the security guidance - as much as possible - with existing guidance from the IAEA for the transport of radioactive sources and nuclear material. It is also intended to harmonize with model requirements developed in 2002-2003 by the United Nations Economic and Social Council's Committee of Experts on the Transport of Dangerous Goods and on the Globally Harmonised System of Classification and Labelling of Chemicals which was issued as general security guidelines for all dangerous goods, including radioactive material, and that will shortly be implemented as binding regulations by the international modal

Guidance for performing preliminary assessments under CERCLA

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-09-01

EPA headquarters and a national site assessment workgroup produced this guidance for Regional, State, and contractor staff who manage or perform preliminary assessments (PAs). EPA has focused this guidance on the types of sites and site conditions most commonly encountered. The PA approach described in this guidance is generally applicable to a wide variety of sites. However, because of the variability among sites, the amount of information available, and the level of investigative effort required, it is not possible to provide guidance that is equally applicable to all sites. PA investigators should recognize this and be aware that variation from this guidance may be necessary for some sites, particularly for PAs performed at Federal facilities, PAs conducted under EPA`s Environmental Priorities Initiative (EPI), and PAs at sites that have previously been extensively investigated by EPA or others. The purpose of this guidance is to provide instructions for conducting a PA and reporting results. This guidance discusses the information required to evaluate a site and how to obtain it, how to score a site, and reporting requirements. This document also provides guidelines and instruction on PA evaluation, scoring, and the use of standard PA scoresheets. The overall goal of this guidance is to assist PA investigators in conducting high-quality assessments that result in correct site screening or further action recommendations on a nationally consistent basis.

76 FR 9028 - Guidance for Industry: Potency Tests for Cellular and Gene Therapy Products; Availability

Science.gov (United States)

2011-02-16

...] Guidance for Industry: Potency Tests for Cellular and Gene Therapy Products; Availability AGENCY: Food and... Therapy Products'' dated January 2011. The guidance document provides manufacturers of cellular and gene... for Industry: Potency Tests for Cellular and Gene Therapy Products'' dated January 2011. The guidance...

Program Management at the National Nuclear Security Administration Office of Defense Nuclear Security: A Review of Program Management Documents and Underlying Processes

International Nuclear Information System (INIS)

Madden, Michael S.

2010-01-01

The scope of this paper is to review the National Nuclear Security Administration Office of Defense Nuclear Security (DNS) program management documents and to examine the underlying processes. The purpose is to identify recommendations for improvement and to influence the rewrite of the DNS Program Management Plan (PMP) and the documentation supporting it. As a part of this process, over 40 documents required by DNS or its stakeholders were reviewed. In addition, approximately 12 other documents produced outside of DNS and its stakeholders were reviewed in an effort to identify best practices. The complete list of documents reviewed is provided as an attachment to this paper.

HER2 testing of gastro-oesophageal adenocarcinoma: a commentary and guidance document from the Association of Clinical Pathologists Molecular Pathology and Diagnostics Committee.

Science.gov (United States)

Wong, Newton A C S; Amary, Fernanda; Butler, Rachel; Byers, Richard; Gonzalez, David; Haynes, Harry R; Ilyas, Mohammad; Salto-Tellez, Manuel; Taniere, Philippe

2018-05-01

The use of biologics targeted to the human epidermal growth factor receptor 2 (HER2) protein is the latest addition to the armamentarium used to fight advanced gastric or gastro-oesophageal junction adenocarcinoma. The decision to treat with the biologic trastuzumab is completely dependent on HER2 testing of tumour tissue. In 2017, the College of American Pathologists, American Society for Clinical Pathology and the American Society of Clinical Oncology jointly published guidelines for HER2 testing and clinical decision making in gastro-oesophageal adenocarcinoma. The Association of Clinical Pathologists Molecular Pathology and Diagnostics Committee has issued the following document as a commentary of these guidelines and, in parallel, to provide guidance on HER2 testing in National Health Service pathology departments within the UK. This guidance covers issues related to case selection, preanalytical aspects, analysis and interpretation of such HER2 testing. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Physical protection of shipments of irradiated reactor fuel; Interim guidance. Regulatory report

International Nuclear Information System (INIS)

1980-06-01

During May, 1979, the U.S. Nuclear Regulatory Commission approved for issuance in effective form new interim regulations for strengthening the protection of spent fuel shipments against sabotage and diversion. The new regulations were issued without benefit of public comment, but comments from the public were solicited after the effective date. Based upon the public comments received, the interim regulations were amended and reissued in effective form as a final interim rule in May, 1980. The present document supersedes a previously issued interim guidance document, NUREG-0561 (June, 1979) which accompanied the original rule. This report has been revised to conform to the new interim regulations on the physical protection of shipments of irradiated reactor fuel which are likely to remain in effect until the completion of an ongoing research program concerning the response of spent fuel to certain forms of sabotage, at which time the regulations may be rescinded, modified or made permanent, as appropriate. This report discusses the amended regulations and provides a basis on which licensees can develop an acceptable interim program for the protection of spent fuel shipments

76 FR 6143 - Draft Guidance for Industry on “Target Animal Safety and Effectiveness Protocol Development and...

Science.gov (United States)

2011-02-03

... this document is to provide sponsors guidance in preparation of study protocols for review by the Center for Veterinary Medicine (CVM), Office of New Animal Drug Evaluation (ONADE), to reduce the time to... Development and Submission.'' The purpose of this document is to provide sponsors guidance in preparation of...

Waste Management System Requirement document

International Nuclear Information System (INIS)

1990-04-01

This volume defines the top level technical requirements for the Monitored Retrievable Storage (MRS) facility. It is designed to be used in conjunction with Volume 1, General System Requirements. Volume 3 provides a functional description expanding the requirements allocated to the MRS facility in Volume 1 and, when appropriate, elaborates on requirements by providing associated performance criteria. Volumes 1 and 3 together convey a minimum set of requirements that must be satisfied by the final MRS facility design without unduly constraining individual design efforts. The requirements are derived from the Nuclear Waste Policy Act of 1982 (NWPA), the Nuclear Waste Policy Amendments Act of 1987 (NWPAA), the Environmental Protection Agency's (EPA) Environmental Standards for the Management and Disposal of Spent Nuclear Fuel (40 CFR 191), NRC Licensing Requirements for the Independent Storage of Spent Nuclear and High-Level Radioactive Waste (10 CFR 72), and other federal statutory and regulatory requirements, and major program policy decisions. This document sets forth specific requirements that will be fulfilled. Each subsequent level of the technical document hierarchy will be significantly more detailed and provide further guidance and definition as to how each of these requirements will be implemented in the design. Requirements appearing in Volume 3 are traceable into the MRS Design Requirements Document. Section 2 of this volume provides a functional breakdown for the MRS facility. 1 tab

Developing guidelines for incorporating managing demand into WSDOT planning and programming: transportation demand management guidance for corridor planning studies.

Science.gov (United States)

2016-02-01

The Washington State Department of Transportation (WSDOT) regional planning programs address current and forecasted deficiencies of State highways through the conduct of corridor studies. This Guidance for the conduct of corridor planning studies is ...

Documentation of SPECTROM-55: A finite element thermohydrogeological analysis program

International Nuclear Information System (INIS)

Osnes, J.D.; Ratigan, J.L.; Loken, M.C.; Parrish, D.K.

1985-12-01

SPECTROM-55 is a finite element computer program developed by RE/SPEC Inc. for analyses of coupled heat and fluid transfer through fully saturated porous media. The theoretical basis for the mathematical model, the implementation of the mathematical model into the computer code, the verification and validation efforts with the computer code, and the code support and continuing documentation are described in this document. The program is especially suited for analyses of the regional hydrogeology in the vicinity of a heat-generating nuclear waste repository. These applications typically involve forced and free convection in a ground-water flow system. The program provides transient or steady-state temperatures, pressures, and fluid velocities resulting from the application of a variety of initial and boundary conditions to bodies with complicated shapes. The boundary conditions include constant heat and fluid fluxes, convective heat transfer, constant temperature, and constant pressure. Initial temperatures and pressures can be specified. Composite systems of anisotropic materials, such as geologic strata, can be defined in either planar or axisymmetric configurations. Constant or varying volumetric heat generation, such as decaying heat generation from radioactive waste, can be specified

[International trend of guidance for nanomaterial risk assessment].

Science.gov (United States)

Hirose, Akihiko

2013-01-01

In the past few years, several kinds of opinions or recommendations on the nanomaterial safety assessment have been published from international or national bodies. Among the reports, the first practical guidance of risk assessment from the regulatory body was published from the European Food Safety Authorities in May 2011, which included the determination of exposure scenario and toxicity testing strategy. In October 2011, European Commission (EC) adopted the definition of "nanomaterial" for regulation. And more recently, Scientific Committee on Consumer Safety of EC released guidance for assessment of nanomaterials in cosmetics in June 2012. A series of activities in EU marks an important step towards realistic safety assessment of nanomaterials. On the other hand, the US FDA announced a draft guidance for industry in June 2011, and then published draft guidance documents for both "Cosmetic Products" and "Food Ingredients and Food Contact Substances" in April 2012. These draft documents do not restrictedly define the physical properties of nanomaterials, but when manufacturing changes alter the dimensions, properties, or effects of an FDA-regulated product, the products are treated as new products. Such international movements indicate that most of nanomaterials with any new properties would be assessed or regulated as new products by most of national authorities in near future, although the approaches are still case by case basis. We will introduce such current international activities and consideration points for regulatory risk assessment.

Headquarters Air Force Logistics Command guidance manual for hazardous waste minimization (PACER REDUCE): Hazardous Waste Remedial Actions Program

International Nuclear Information System (INIS)

Jones, L.W.; Weeter, D.; Roth, J.A.; Debelak, K.A.; Bowers, A.R.

1988-09-01

This manual provides guidance for the Air Force Logistics Command (AFLC) Waste Minimization Program, called PACER REDUCE, and applies to all AFLC installations and personel who are responsible for implementing and monitoring activities relating to PACER REDUCE. This guidance for waste minimization provides management and technical approaches for assessing potential waste reduction techniques and for making informed decisions concerning industrial process and waste stream management. Such actions will assist in achieving regulatory compliance with the Resource Conservation and Recovery Act of 1976 as updated by the Hazardous and Solid Waste Amendments of 1984. 37 refs., 14 figs., 22 tabs

Accuracy Analysis of Lunar Lander Terminal Guidance Algorithm

Directory of Open Access Journals (Sweden)

E. K. Li

2017-01-01

Full Text Available This article studies a proposed analytical algorithm of the terminal guidance for the lunar lander. The analytical solution, which forms the basis of the algorithm, was obtained for a constant acceleration trajectory and thrust vector orientation programs that are essentially linear with time. The main feature of the proposed algorithm is a completely analytical solution to provide the lander terminal guidance to the desired spot in 3D space when landing on the atmosphereless body with no numerical procedures. To reach 6 terminal conditions (components of position and velocity vectors at the final time are used 6 guidance law parameters, namely time-to-go, desired value of braking deceleration, initial values of pitch and yaw angles and rates of their change. In accordance with the principle of flexible trajectories, this algorithm assumes the implementation of a regularly updated control program that ensures reaching terminal conditions from the current state that corresponds to the control program update time. The guidance law parameters, which ensure that terminal conditions are reached, are generated as a function of the current phase coordinates of a lander. The article examines an accuracy and reliability of the proposed analytical algorithm that provides the terminal guidance of the lander in 3D space through mathematical modeling of the lander guidance from the circumlunar pre-landing orbit to the desired spot near the lunar surface. A desired terminal position of the lunar lander is specified by the selenographic latitude, longitude and altitude above the lunar surface. The impact of variations in orbital parameters on the terminal guidance accuracy has been studied. By varying the five initial orbit parameters (obliquity, ascending node longitude, argument of periapsis, periapsis height, apoapsis height when the terminal spot is fixed the statistic characteristics of the terminal guidance algorithm error according to the terminal

77 FR 6625 - Meeting the Challenge of Pandemic Influenza: Ethical Guidance for Leaders and Health Care...

Science.gov (United States)

2012-02-08

... DEPARTMENT OF VETERANS AFFAIRS Meeting the Challenge of Pandemic Influenza: Ethical Guidance for... guidance document entitled ``Meeting the Challenge of Pandemic Influenza: Ethical Guidance for Leaders and... should indicate that they are submitted in response to ``Meeting the Challenge of Pandemic Influenza...

River City High School Guidance Services: A Conceptual Model.

Science.gov (United States)

American Coll. Testing Program, Iowa City, IA.

This model describes how the guidance staff at a hypothetical high school communicated the effectiveness of the guidance program to students, parents, teachers, and administrators. A description of the high school is presented, and guidance services and personnel are described. A conceptual model responding to student needs is outlined along with…

Functional requirements document for measuring emissions of airborne radioactive materials

International Nuclear Information System (INIS)

Glissmeyer, J.A.; Alvarez, J.L.; Hoover, M.D.; Newton, G.C.; McFarland, A.R.; Rodgers, J.C.

1994-11-01

This document states the general functional requirements for systems and procedures for measuring emissions of airborne radioactive materials from facilities administered by the Westinghouse Hanford Company (WHC). The following issues are addressed in this document: lg-bullet definition of the program objectives lg-bullet selection of the overall approach to collecting the samples lg-bullet sampling equipment design lg-bullet sampling equipment maintenance and quality assurance issues. The following issues are not addressed in this document: lg-bullet air sampling in work areas or containments lg-bullet selection of specific on-line sample monitoring instrumentation lg-bullet analyzing collected samples lg-bullet reporting and interpreting results. The document provides equipment design guidance that is performance based rather than prescriptive. Locations from which samples are obtained should exhibit mixing of the contaminants with the airstream and acceptable air flow characteristics. Sample collection equipment and effluent and sample flow elements should meet defined performance standards. Quality control and assurance requirements specific to sample collection, equipment inspection, and calibration are presented. Key sample collection performance requirements are summarized in Section 5.4. The intent of this document is to assist WHC in demonstrating a high quality of air emission measurements with verified system performance based on documented system design, testing, inspection, and maintenance

Repository-Based Software Engineering Program: Working Program Management Plan

Science.gov (United States)

1993-01-01

Repository-Based Software Engineering Program (RBSE) is a National Aeronautics and Space Administration (NASA) sponsored program dedicated to introducing and supporting common, effective approaches to software engineering practices. The process of conceiving, designing, building, and maintaining software systems by using existing software assets that are stored in a specialized operational reuse library or repository, accessible to system designers, is the foundation of the program. In addition to operating a software repository, RBSE promotes (1) software engineering technology transfer, (2) academic and instructional support of reuse programs, (3) the use of common software engineering standards and practices, (4) software reuse technology research, and (5) interoperability between reuse libraries. This Program Management Plan (PMP) is intended to communicate program goals and objectives, describe major work areas, and define a management report and control process. This process will assist the Program Manager, University of Houston at Clear Lake (UHCL) in tracking work progress and describing major program activities to NASA management. The goal of this PMP is to make managing the RBSE program a relatively easy process that improves the work of all team members. The PMP describes work areas addressed and work efforts being accomplished by the program; however, it is not intended as a complete description of the program. Its focus is on providing management tools and management processes for monitoring, evaluating, and administering the program; and it includes schedules for charting milestones and deliveries of program products. The PMP was developed by soliciting and obtaining guidance from appropriate program participants, analyzing program management guidance, and reviewing related program management documents.

Request for Guidance on PSD Applicability Determinations for Boiler Emissions

Science.gov (United States)

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Guidance on the scientific requirements for health claims related to antioxidants, oxidative damage and cardiovascular health

DEFF Research Database (Denmark)

Tetens, Inge

2011-01-01

The Panel on Dietetic Products, Nutrition and Allergies (NDA) was asked by the European Food Safety Authority (EFSA) t to draft guidance on scientific requirements for health claims related to antioxidants, oxidative damage and cardiovascular health. This guidance has been drawn from scientific...... opinions of the NDA Panel on such health claims. Thus, this guidance document represents the views of the NDA Panel based on the experience gained to date with the evaluation of health claims in these areas. It is not intended that the document should include an exhaustive list of beneficial effects...

Fire Protection Program Manual

Energy Technology Data Exchange (ETDEWEB)

Sharry, J A

2012-05-18

This manual documents the Lawrence Livermore National Laboratory (LLNL) Fire Protection Program. Department of Energy (DOE) Orders 420.1B, Facility Safety, requires LLNL to have a comprehensive and effective fire protection program that protects LLNL personnel and property, the public and the environment. The manual provides LLNL and its facilities with general information and guidance for meeting DOE 420.1B requirements. The recommended readers for this manual are: fire protection officers, fire protection engineers, fire fighters, facility managers, directorage assurance managers, facility coordinators, and ES and H team members.

78 FR 78974 - Agency Information Collection Activities; Proposed Collection; Comment Request; Guidance for...

Science.gov (United States)

2013-12-27

... chapter granting FDA authority to regulate the manufacture, marketing, and distribution of tobacco... related to substantial equivalence. In a Level 1 guidance document issued under the Good Guidances Practices regulation (21 CFR 10.115), FDA provides recommendations intended to assist persons submitting...

78 FR 32668 - Draft Guidance for Industry: Changes to an Approved Application: Biological Products: Human Blood...

Science.gov (United States)

2013-05-31

..., including Source Plasma, with recommendations intended to assist with determining which reporting mechanism... final version of the guidance, submit either electronic or written comments on the draft guidance by... INFORMATION section for electronic access to the draft guidance document. Submit electronic comments on the...

21 CFR 10.115 - Good guidance practices.

Science.gov (United States)

2010-04-01

... understanding, or other communications directed to individual persons or firms. (c) What other terms have a... Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL... communication that are excluded from the definition of guidance document to informally communicate new or...

Development of recommended practices and guidance documents for upstream oil and gas flow measurement

Energy Technology Data Exchange (ETDEWEB)

Dahl, Eivind; Scheers, Lex; Ting, Frank; Letton, Chip

2005-07-01

As first stated in the Introduction, improvements in multiphase flow meters during the last 15 years have resulted in their increased usage in upstream oil and gas applications, especially in difficult offshore locations both topside and deep subsea. To address user needs for information and standardization in the area, documentation has recently been created under the auspices of the NFOGM, API, and ISO. Our intent here was to familiarize potential users with the three new documents, which should be helpful in a number of respects, e.g., (a) distribution of best knowledge and operational practices on the subject, (b) provision of a common language for discussing multiphase flow, and (c) accounting for the requirements of governing regulatory authorities. At this stage of completion of NFOGM, API, and ISO reports, a natural question arises as to what the future holds for another round of flow measurement documentation. Candidate areas include: 1) In Situ Verification of Multiphase Flow Meters. 2) Wet Gas Flow Measurement. 3) Flare Gas Meters. 4) Virtual Metering. 5) Composition and Phase Behavior Issues In Measurement. 6) Flow Measurement Uncertainty. Addressing certain of these is already being proposed in several possible venues, among which are (1) the DeepStar Consortium, (2) a JIP for investigating total system (meter + flowline + separator) uncertainty organized by a group at Tulsa University, and (3) a program for development of drilling and production capabilities in ultradeep water to be sponsored by the US Department of Energy. The creation of the three documents discussed in this paper demonstrates the benefits that strong international cooperation can achieve in producing standardization documents, ensuring their true global input and acceptance. On the other hand, it should also be questioned why two or more documents are required, which are the result of much duplication of effort. For example, although there are differences between API RP86 and the

Moisture Control Guidance for Commercial and Public Buildings (EPA 402-F-13053)

Science.gov (United States)

This document provides guidance to designers, construction mangers, and building operation/maintenance managers to improve IEQ and reduce risks of encountering IEQ problems due to insufficient moisture control. EPA will be producing a document entitled "Moisture Control Guida...

75 FR 62820 - Screening Framework Guidance for Providers of Synthetic Double-Stranded DNA

Science.gov (United States)

2010-10-13

... Providers of Synthetic Double- Stranded DNA AGENCY: Department of Health and Human Services, Office of the.... Government has developed Guidance that provides a framework for screening synthetic double-stranded DNA (dsDNA). This document, the Screening Framework Guidance for Providers of Synthetic Double-Stranded DNA...

IRIS Summary and Supporting Documents for Methylmercury ...

Science.gov (United States)

In January 2001, U.S. EPA finalized the guidance for methylmercury in the water quality criteria for states and authorized tribes. The links below take you to the best resources for this guidance. This final Guidance for Implementing the January 2001 Methylmercury Water Quality Criterion provides technical guidance to states and authorized tribes on how they may want to use the January 2001 fish tissue-based recommended water quality criterion for methylmercury in surface water protection programs (e.g., TMDLs, NPDES permitting). The guidance addresses questions related to water quality standards adoption (e.g., site-specific criteria, variances), assessments, monitoring, TMDLs, and NPDES permitting. The guidance consolidates existing EPA guidance where relevant to mercury.

78 FR 102 - Guidance for Industry and Food and Drug Administration Staff; eCopy Program for Medical Device...

Science.gov (United States)

2013-01-02

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-D-1056] Guidance for Industry and Food and Drug Administration Staff; eCopy Program for Medical Device Submissions; Availability AGENCY: Food and Drug Administration, HHS. ACTION: Notice. SUMMARY: The Food and Drug...

77 FR 63837 - Draft Guidance for Industry and Food and Drug Administration Staff; eCopy Program for Medical...

Science.gov (United States)

2012-10-17

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-D-1056] Draft Guidance for Industry and Food and Drug Administration Staff; eCopy Program for Medical Device Submissions; Availability AGENCY: Food and Drug Administration, HHS. ACTION: Notice. SUMMARY: The Food and...

Improvements in inservice testing regulatory guidance

Energy Technology Data Exchange (ETDEWEB)

Campbell, P.L.

1996-12-01

Over the last few years, the NRC has issued guidance to licensees toward improving the quality of requests for relief or alternatives to the code requirements and bring some measure of consistency to the implementation of the code requirements. Based on the majority of the recent submittals, the overall quality has improved. If all of the steps in the internal process for responding to the requests are timely, the review of an updated program can be completed in six to nine months. When a single or only a few requests are submitted, the staff is generally able to complete an evaluation in less than three months. When schedules are related to outages or exigent circumstances, the NRC responds accordingly. The improvements in schedules can be attributed to publication of staff guideline documents, licensees` efforts in preparing more complete descriptions and justification and an increase in the number of NRC technical staff reviewers assigned to IST.

Improvements in inservice testing regulatory guidance

International Nuclear Information System (INIS)

Campbell, P.L.

1996-01-01

Over the last few years, the NRC has issued guidance to licensees toward improving the quality of requests for relief or alternatives to the code requirements and bring some measure of consistency to the implementation of the code requirements. Based on the majority of the recent submittals, the overall quality has improved. If all of the steps in the internal process for responding to the requests are timely, the review of an updated program can be completed in six to nine months. When a single or only a few requests are submitted, the staff is generally able to complete an evaluation in less than three months. When schedules are related to outages or exigent circumstances, the NRC responds accordingly. The improvements in schedules can be attributed to publication of staff guideline documents, licensees' efforts in preparing more complete descriptions and justification and an increase in the number of NRC technical staff reviewers assigned to IST

Individual plant examination: Submittal guidance

International Nuclear Information System (INIS)

1989-08-01

Based on a Policy Statement on Severe Accidents Regarding Future Designs and Existing Plants, the performance of a plant examination is requested from the licensee of each nuclear power plant. The plant examination looks for vulnerabilities to severe accidents and cost-effective safety improvements that reduce or eliminate the important vulnerabilities. This document delineates guidance for reporting the results of that plant examination. 38 refs., 2 tabs

Variable & Recode Definitions - SEER Documentation

Science.gov (United States)

Resources that define variables and provide documentation for reporting using SEER and related datasets. Choose from SEER coding and staging manuals plus instructions for recoding behavior, site, stage, cause of death, insurance, and several additional topics. Also guidance on months survived, calculating Hispanic mortality, and site-specific surgery.

78 FR 42086 - Draft Guidance for Industry on Arsenic in Apple Juice: Action Level; Supporting Document for...

Science.gov (United States)

2013-07-15

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-D-0322... of good manufacturing practices. It also describes FDA's intended sampling and enforcement approach... the guidance, submit either electronic or written comments on the draft guidance by September 13, 2013...

Multimodality and video observation in “Collective Academic Supervision” in the Master Program in Guidance, Aarhus University, Denmark

DEFF Research Database (Denmark)

Nordentoft, Helle Merete; Buhl, Mie

2012-01-01

In the preface of his book on counseling McLeod (2003, p. xvii) is wondering how this practice appear to be so simple and yet so vastly complicated. What could be simpler than being and interested interviewer and listener? Still, the complexity of what is involved in professional interaction...... practices can be difficult to pinpoint. In this presentation we argue that an analytical approach to the professional’s own practice provides valuable knowledge of how to practice guidance and counseling. Furthermore, we argue that this must be addressed as an active part of the master programme’s pedagogy...... observations of group supervision sessions at the Danish Master Program in Guidance....

Guidance on assessing the methodological and reporting quality of toxicologically relevant studies: A scoping review.

Science.gov (United States)

Samuel, Gbeminiyi O; Hoffmann, Sebastian; Wright, Robert A; Lalu, Manoj Mathew; Patlewicz, Grace; Becker, Richard A; DeGeorge, George L; Fergusson, Dean; Hartung, Thomas; Lewis, R Jeffrey; Stephens, Martin L

2016-01-01

Assessments of methodological and reporting quality are critical to adequately judging the credibility of a study's conclusions and to gauging its potential reproducibility. To aid those seeking to assess the methodological or reporting quality of studies relevant to toxicology, we conducted a scoping review of the available guidance with respect to four types of studies: in vivo and in vitro, (quantitative) structure-activity relationships ([Q]SARs), physico-chemical, and human observational studies. Our aims were to identify the available guidance in this diverse literature, briefly summarize each document, and distill the common elements of these documents for each study type. In general, we found considerable guidance for in vivo and human studies, but only one paper addressed in vitro studies exclusively. The guidance for (Q)SAR studies and physico-chemical studies was scant but authoritative. There was substantial overlap across guidance documents in the proposed criteria for both methodological and reporting quality. Some guidance documents address toxicology research directly, whereas others address preclinical research generally or clinical research and therefore may not be fully applicable to the toxicology context without some translation. Another challenge is the degree to which assessments of methodological quality in toxicology should focus on risk of bias - as in clinical medicine and healthcare - or be broadened to include other quality measures, such as confirming the identity of test substances prior to exposure. Our review is intended primarily for those in toxicology and risk assessment seeking an entry point into the extensive and diverse literature on methodological and reporting quality applicable to their work. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Builders Challenge Quality Criteria Support Document

Energy Technology Data Exchange (ETDEWEB)

None

2009-06-01

This document provides guidance to U.S. home builders participating in Builders Challenge. To qualify for the Builders Challenge, a home must score 70 or less on the EnergySmart Home Scale (E-Scale). Homes also must meet the Builders Challenge Quality Cri

Practical guidance for defining a smart grid modernization strategy the case of distribution

CERN Document Server

Madrigal, Marcelino

2015-01-01

This document provides some practical guidance on how utilities can define their own smart grid vision, identify priorities, and structure investment plans. While most of these strategic aspects apply to any area of the electricity grid, the document focuses on the segment of distribution. The guidance includes key building blocks that are needed to modernize the distribution grid and provides examples of grid modernization projects. Potential benefits that can be achieved (in monetary terms) for a given investment range are also discussed.The concept of the smart grid is relevant to any grid

78 FR 70307 - Guidance for Industry: Preclinical Assessment of Investigational Cellular and Gene Therapy...

Science.gov (United States)

2013-11-25

...] Guidance for Industry: Preclinical Assessment of Investigational Cellular and Gene Therapy Products... Assessment of Investigational Cellular and Gene Therapy Products'' dated November 2013. The guidance document... products reviewed by the Office of Cellular, Tissue and Gene Therapies (OCTGT). The product areas covered...

Unified State Plan for Guidance, Counseling and Placement in Colorado. Grades 7-12.

Science.gov (United States)

Terrill, Jerry; And Others

This guide, one of three units in the Colorado state plan for guidance program development, is written for educators as both a guideline and a needs assessment instrument to assist in the identification of deficit areas in school guidance programs. In a beginning section, this unit for grades 7-12 provides a brief philosophy of guidance and…

An improved instrument setpoint control program

International Nuclear Information System (INIS)

Cash, J.S. Jr.; George, R.T.; Kincaid, S.C.

1991-01-01

Instrument setpoints have a definite and often significant impact on plant safety, reliability, and availability. Although typically overshadowed by plant design, modification, and physical change activities, instrument setpoints can alter plant status and system operating characteristics just as significantly. Recognizing the need for a formal program that provides configuration control of instrument setpoints, provides a readily accessible and clearly documented basis for instrument setpoints, and integrates and coordinates operations, engineering, and maintenance activities that influence the basis for instrument setpoints, Philadelphia Electric Company (PECo) is developing an Improved Instrument Setpoint Control Program (IISCP) that incorporates current industry guidance and practices and state-of-the-art information systems technology. The IISCP was designed around PECo's then existing business processes for setpoint control, determination, and maintenance. A task force representing the various constituencies from both plants and the engineering and services organizations were formed to identify objectives and design features for the IISCP. Utilizing industry standards and guidance, regulatory documents, the experiences and good practices obtained from other utilities, and PECo's nuclear group strategies, objectives, and goals, specific objectives were identified to enhance the business processes

United Nations Environment Program - Sustainable Purchasing Guidance Profile

Science.gov (United States)

To help you find the resource that is right for your organization, EPA conducted a scan of the landscape and developed summary profiles of some of the leading sources of sustainable purchasing guidance around the globe.

Applicability of NSR Review Circumvention Guidance to 3M - Maplewood, Minnesota

Science.gov (United States)

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

RCRA corrective action program guide (Interim)

Energy Technology Data Exchange (ETDEWEB)

1993-05-01

The US Department of Energy (DOE) is responsible for compliance with an increasingly complex spectrum of environmental regulations. One of the most complex programs is the corrective action program proposed by the US Environmental Protection Agency (EPA) under the authority of the Resource Conservation and Recovery Act (RCRA) as amended by the Hazardous and Solid Waste Amendments (HSWA). The proposed regulations were published on July 27, 1990. The proposed Subpart S rule creates a comprehensive program for investigating and remediating releases of hazardous wastes and hazardous waste constituents from solid waste management units (SWMUs) at facilities permitted to treat, store, or dispose of hazardous wastes. This proposed rule directly impacts many DOE facilities which conduct such activities. This guidance document explains the entire RCRA Corrective Action process as outlined by the proposed Subpart S rule, and provides guidance intended to assist those persons responsible for implementing RCRA Corrective Action at DOE facilities.

75 FR 53316 - Draft Guidance for Food and Drug Administration Staff and Tobacco Retailers on Civil Money...

Science.gov (United States)

2010-08-31

...] Draft Guidance for Food and Drug Administration Staff and Tobacco Retailers on Civil Money Penalties and... guidance entitled ``Civil Money Penalties and No-Tobacco-Sale Orders for Tobacco Retailers.'' This guidance document is intended to describe FDA's current policies with respect to civil money penalties and no...

DOE Defense Program (DP) safety programs. Final report, Task 003

International Nuclear Information System (INIS)

1998-01-01

The overall objective of the work on Task 003 of Subcontract 9-X52-W7423-1 was to provide LANL with support to the DOE Defense Program (DP) Safety Programs. The effort included the identification of appropriate safety requirements, the refinement of a DP-specific Safety Analysis Report (SAR) Format and Content Guide (FCG) and Comprehensive Review Plan (CRP), incorporation of graded approach instructions into the guidance, and the development of a safety analysis methodologies document. All tasks which were assigned under this Task Order were completed. Descriptions of the objectives of each task and effort performed to complete each objective is provided here

32 CFR 70.10 - Complaints concerning decisional documents and index entries.

Science.gov (United States)

2010-07-01

... declining to list that aspect of the service record as an issue. (v) Guidance as to other types of complaints. The following guidance governs other specified types of complaints: (A) The Stipulation of... noted in the decisional document or index entries: (Authentication) Attachment 2—Joint Service Review...

Quality assurance program plan for low-level waste at the WSCF Laboratory

International Nuclear Information System (INIS)

Morrison, J.A.

1994-01-01

The purpose of this document is to provide guidance for the implementation of the Quality Assurance Program Plan (QAPP) for the management of low-level waste at the Waste Sampling and Characterization Facility (WSCF) Laboratory Complex as required by WHC-CM-4-2, Quality Assurance Manual, which is based on Quality Assurance Program Requirements for Nuclear Facilities, NQA-1 (ASME)

Deep Energy Retrofit Guidance for the Building America Solutions Center

Energy Technology Data Exchange (ETDEWEB)

Less, Brennan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Walker, Iain [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2015-01-01

The U.S. DOE Building America program has established a research agenda targeting market-relevant strategies to achieve 40% reductions in existing home energy use by 2030. Deep Energy Retrofits (DERs) are part of the strategy to meet and exceed this goal. DERs are projects that create new, valuable assets from existing residences, by bringing homes into alignment with the expectations of the 21st century. Ideally, high energy using, dated homes that are failing to provide adequate modern services to their owners and occupants (e.g., comfortable temperatures, acceptable humidity, clean, healthy), are transformed through comprehensive upgrades to the building envelope, services and miscellaneous loads into next generation high performance homes. These guidance documents provide information to aid in the broader market adoption of DERs.

International guidance activities

International Nuclear Information System (INIS)

Richardson, Allan C.B.

1989-01-01

International principles for setting Protective Action Guides (PAGs) are contained in two key documents that contain identical statements. One is Publication Number 40 of the ICRP, which was issued in 1985. The title is 'Protection of the Public in the Event of Major Radiation Accidents, Principles for Planning'. The other is the IAEA's Safety Series Publication Number 72, also issued in 1985, written by many of the same authors and titled, 'Principles for Establishing Intervention Levels'. The principles that were set forth in these documents were identical, were incomplete, and they are, unfortunately, the only principles that are now in effect, while proposed revisions go through one draft after another. There are several such draft revisions that are of significance. The most important is that of the ICRP. The basic guidance that applies to most planned exposure to radiation is ICRP Publication 26. That document has been under revision by the Commission for a number of years, and the new version will, for the first time, include recommendations for emergency response. They are now getting close to closure, and I think it should be a very much improved and useful document. But it isn't finished yet. Such guidance doesn't get developed in a vacuum, and there have been a couple of parallel efforts which have provided significant input to the ICRP, which is essentially a behind-closed-doors effort. These other efforts are more open. One of these is being carried out within the IAEA, which has convened annual meetings of national experts for a number of years in Vienna, to generate a replacement for Safety Series No. 72, mentioned earlier. There is a meeting scheduled this December to complete this effort; and, hopefully, we will reach closure at that meeting on at least the basic principles. The Nuclear Energy Agency (NEA) has also been at work. It has convened a group of experts from member nations that have been developing recommendations. There is an overlap

National Household Education Surveys Program of 2012: Data File User's Manual. Parent and Family Involvement in Education Survey. Early Childhood Program Participation Survey. NCES 2015-030

Science.gov (United States)

McPhee, C.; Bielick, S.; Masterton, M.; Flores, L.; Parmer, R.; Amchin, S.; Stern, S.; McGowan, H.

2015-01-01

The 2012 National Household Education Surveys Program (NHES:2012) Data File User's Manual provides documentation and guidance for users of the NHES:2012 data files. The manual provides information about the purpose of the study, the sample design, data collection procedures, data processing procedures, response rates, imputation, weighting and…

Guidance levels, achievable doses and expectation levels

International Nuclear Information System (INIS)

Li, Lianbo; Meng, Bing

2002-01-01

The National Radiological Protection Board (NRPB), the International Atomic Energy Agency (IAEA) and the Commission of the European Communities (CEC) published their guidance levels and reference doses for typical X-ray examination and nuclear medicine in their documents in 1993, 1994 and 1996 respectively. From then on, the concept of guidance levels or reference doses have been applied to different examinations in the field of radiology and proved to be effective for reduction of patient doses. But the guidance levels or reference doses are likely to have some shortcomings and can do little to make further reduction of patient dose in the radiology departments where patient dose are already below them. For this reason, the National Radiological Protection Board (NRPB) proposed a concept named achievable doses which are based on the mean dose observed for a selected sample of radiology departments. This paper will review and discuss the concept of guidance levels and achievable doses, and propose a new concept referred to as Expectation Levels that will encourage the radiology departments where patient dose are already below the guidance levels to keep patient dose as low as reasonably achievable. Some examples of the expectation levels based on the data published by a few countries are also illustrated in this paper

Programming WCF Services

CERN Document Server

Lowy, Juval

2008-01-01

Written by Microsoft software legend Juval Lowy, Programming WCF Services is the authoritative introduction to Microsoft's new, and some say revolutionary, unified platform for developing service-oriented applications (SOA) on Windows. Relentlessly practical, the book delivers insight, not documentation, to teach developers what they need to know to build the next generation of SOAs. Not only will this book make you a WCF expert, it will deliver techniques and guidance to become a better software engineer. It's the Rosetta Stone of WCF.

Program strategy document for the nuclear materials. Transportation Technology Center (FY 80)

International Nuclear Information System (INIS)

Jefferson, R.M.

1980-04-01

The TTC's program is divided into four principal areas, Technology and Information Center, Systems Development, Technology, and Institutional Issues. These areas are broken into activities, elements, and subelements which are delineated in this document

General Merchandise 50% Energy Savings Technical Support Document

Energy Technology Data Exchange (ETDEWEB)

Hale, E.; Leach, M.; Hirsch, A.; Torcellini, P.

2009-09-01

This report documents technical analysis for medium-box general merchandise stores aimed at providing design guidance that achieves whole-building energy savings of at least 50% over ASHRAE Standard 90.1-2004.

Guidance to Risk-Informed Evaluation of Technical Specifications using PSA

International Nuclear Information System (INIS)

Baeckstroem, Ola; Haeggstroem, Anna; Maennistoe, Ilkka

2010-04-01

This report presents guidance for evaluation of Technical Specification conditions with PSA. It covers quality in PSA, how to verify that the PSA model is sufficiently robust and sufficiently complete and general requirements on methods. Acceptance criteria for evaluation of changes in the TS conditions are presented. As the probabilistic safety assessment (PSA) has developed over the years, it has demonstrated to constitute a useful tool for evaluating many aspects of the TS from a risk point of view. and in that way making the PSAs as well as the decision tools better. This also means that it will be possible to take credit for safety system overcapacity as well as inherent safety features and strength of non-safety classed systems. However, PSA is only one of the tools that shall be used in an evaluation process of TS changes (strengthening/relaxation). PSA is an excellent tool to be used to verify the importance, and thereby possibly relaxation, of TS requirements. But, since PSA is only one tool in the evaluation, it is not sufficient in itself for defining which equipment that shall or shall not have TS requirements. The purpose of this guidance document is to provide general requirements, requirements on methods and acceptance criteria on risk-informed evaluation of TS changes based on PSA. The purpose is not to provide a single solution. As part of the review of the TS conditions this guidance specify requirements on: - Quality verification of the PSA model; - Verification that the PSA model is sufficiently robust with regard to SSCs for which requirements both are and are not defined by the TS; - Verification that the SSCs, for which TS demands are to be evaluated, are modelled in a sufficient manner; - Methods for performing the evaluation; - Which evaluation criteria that shall be used (and how that is verified to be correct); - Acceptance criteria: This guidance also briefly discusses the documentation of the analysis of the TS changes. This guidance

Guidance to risk-informed evaluation of technical specifications using PSA

International Nuclear Information System (INIS)

Baeckstroem, O.; Haeggstroem, A.; Maennistoe, I.

2010-10-01

This report presents guidance for evaluation of Technical Specification conditions with PSA. It covers quality in PSA, how to verify that the PSA model is sufficiently robust and sufficiently complete and general requirements on methods. Acceptance criteria for evaluation of changes in the TS conditions are presented. As the probabilistic safety assessment (PSA) has developed over the years, it has demonstrated to constitute a useful tool for evaluating many aspects of the TS from a risk point of view. and in that way making the PSAs as well as the decision tools better. This also means that it will be possible to take credit for safety system overcapacity as well as inherent safety features and strength of non-safety classed systems. However, PSA is only one of the tools that shall be used in an evaluation process of TS changes (strengthening/relaxation). PSA is an excellent tool to be used to verify the importance, and thereby possibly relaxation, of TS requirements. But, since PSA is only one tool in the evaluation, it is not sufficient in itself for defining which equipment that shall or shall not have TS requirements. The purpose of this guidance document is to provide general requirements, requirements on methods and acceptance criteria on risk-informed evaluation of TS changes based on PSA. The purpose is not to provide a single solution. As part of the review of the TS conditions this guidance specify requirements on: - Quality verification of the PSA model; - Verification that the PSA model is sufficiently robust with regard to SSCs for which requirements both are and are not defined by the TS; - Verification that the SSCs, for which TS demands are to be evaluated, are modelled in a sufficient manner; - Methods for performing the evaluation; - Which evaluation criteria that shall be used (and how that is verified to be correct); - Acceptance criteria: This guidance also briefly discusses the documentation of the analysis of the TS changes. This guidance

Guidance to risk-informed evaluation of technical specifications using PSA

Energy Technology Data Exchange (ETDEWEB)

Baeckstroem, O.; Haeggstroem, A. (Scandpower AB, Stockholm (Sweden)); Maennistoe, I. (VTT, Helsingfors (Finland))

2010-04-15

This report presents guidance for evaluation of Technical Specification conditions with PSA. It covers quality in PSA, how to verify that the PSA model is sufficiently robust and sufficiently complete and general requirements on methods. Acceptance criteria for evaluation of changes in the TS conditions are presented. As the probabilistic safety assessment (PSA) has developed over the years, it has demonstrated to constitute a useful tool for evaluating many aspects of the TS from a risk point of view. and in that way making the PSAs as well as the decision tools better. This also means that it will be possible to take credit for safety system overcapacity as well as inherent safety features and strength of non-safety classed systems. However, PSA is only one of the tools that shall be used in an evaluation process of TS changes (strengthening/relaxation). PSA is an excellent tool to be used to verify the importance, and thereby possibly relaxation, of TS requirements. But, since PSA is only one tool in the evaluation, it is not sufficient in itself for defining which equipment that shall or shall not have TS requirements. The purpose of this guidance document is to provide general requirements, requirements on methods and acceptance criteria on risk-informed evaluation of TS changes based on PSA. The purpose is not to provide a single solution. As part of the review of the TS conditions this guidance specify requirements on: - Quality verification of the PSA model; - Verification that the PSA model is sufficiently robust with regard to SSCs for which requirements both are and are not defined by the TS; - Verification that the SSCs, for which TS demands are to be evaluated, are modelled in a sufficient manner; - Methods for performing the evaluation; - Which evaluation criteria that shall be used (and how that is verified to be correct); - Acceptance criteria: This guidance also briefly discusses the documentation of the analysis of the TS changes. This guidance

Guidance to Risk-Informed Evaluation of Technical Specifications using PSA

Energy Technology Data Exchange (ETDEWEB)

Baeckstroem, Ola; Haeggstroem, Anna (Scandpower AB, Stockholm (Sweden)); Maennistoe, Ilkka (VTT, Helsingfors (Finland))

2010-04-15

This report presents guidance for evaluation of Technical Specification conditions with PSA. It covers quality in PSA, how to verify that the PSA model is sufficiently robust and sufficiently complete and general requirements on methods. Acceptance criteria for evaluation of changes in the TS conditions are presented. As the probabilistic safety assessment (PSA) has developed over the years, it has demonstrated to constitute a useful tool for evaluating many aspects of the TS from a risk point of view. and in that way making the PSAs as well as the decision tools better. This also means that it will be possible to take credit for safety system overcapacity as well as inherent safety features and strength of non-safety classed systems. However, PSA is only one of the tools that shall be used in an evaluation process of TS changes (strengthening/relaxation). PSA is an excellent tool to be used to verify the importance, and thereby possibly relaxation, of TS requirements. But, since PSA is only one tool in the evaluation, it is not sufficient in itself for defining which equipment that shall or shall not have TS requirements. The purpose of this guidance document is to provide general requirements, requirements on methods and acceptance criteria on risk-informed evaluation of TS changes based on PSA. The purpose is not to provide a single solution. As part of the review of the TS conditions this guidance specify requirements on: - Quality verification of the PSA model; - Verification that the PSA model is sufficiently robust with regard to SSCs for which requirements both are and are not defined by the TS; - Verification that the SSCs, for which TS demands are to be evaluated, are modelled in a sufficient manner; - Methods for performing the evaluation; - Which evaluation criteria that shall be used (and how that is verified to be correct); - Acceptance criteria: This guidance also briefly discusses the documentation of the analysis of the TS changes. This guidance

Implementation of NUREG-1318 guidance within the Yucca Mountain Project

International Nuclear Information System (INIS)

La Monica, L.B.; Waddell, J.D.; Hardin, E.L.

1990-01-01

The US Department of Energy's Yucca Mountain Project is implementing a quality assurance program that fulfills the requirements of the US Nuclear Regulatory Commission (NRC). Additional guidance for this program was provided in NUREG 1318, ''Technical Position on Items and Activities in the High-Level Waste Geologic Repository Program Subject to Quality Assurance Requirements'' for identification of items and activities important to public radiological safety and waste isolation. The process and organization for implementing this guidance is discussed. 3 refs., 2 figs

76 FR 23824 - Guidance for Industry: “Computer Crossmatch” (Computerized Analysis of the Compatibility Between...

Science.gov (United States)

2011-04-28

... Plasma Type)'' dated June 2007. DATES: Submit either electronic or written comments on Agency guidances... the Compatibility Between the Donor's Cell Type and the Recipient's Serum or Plasma Type... Serum or Plasma Type)'' dated April 2011. The guidance document provides blood establishments that...

How Should We Treat the Vulnerable?: Qualitative Study of Authoritative Ethics Documents.

Science.gov (United States)

Zagorac, Ivana

2016-01-01

The aim of this study is to explore what actual guidance is provided by authoritative ethics documents regarding the recognition and protection of the vulnerable. The documents included in this analysis are the Belmont Report, the Declaration of Helsinki, The Council for International Organizations of Medical Sciences (CIOMS) Guidelines, and the UNESCO Universal Declaration on Bioethics and Human Rights, including its supplementary report on vulnerability. A qualitative analysis of these documents was conducted in light of three questions: what is vulnerability, who are the vulnerable, and how should the vulnerable be protected? The results show significant differences among the documents regarding the first two questions. None of the documents provides any guidance on the third question (how to protect the vulnerable). These results suggest a great discrepancy between the acknowledged importance of the concept of vulnerability and a general understanding of the scope, content, and practical implications of vulnerability.

Revised guidance on reporting of offshore hydrocarbon releases

International Nuclear Information System (INIS)

1996-11-01

The application offshore of the Reporting of Injuries, Disease and Dangerous Occurrences Regulations 1995 (RIDDOR 1995) has resulted in a new statutory reporting form. The definitions in RIDDOR 95 covering offshore hydrocarbon releases have been slightly revised, making it necessary to revise the guidance on reporting of offshore hydrocarbon releases. RIDDOR 1995 does not affect the existing voluntary arrangements for completion of forms. The receipt of correctly completed forms is important to ensure good output data from the database, and the guidance contained in this document is therefore aimed at assisting completion of the voluntary form. (UK)

A Nordic perspective on career competences and guidance

DEFF Research Database (Denmark)

Thomsen, Rie

This concept note reflects an initiative within the Nordic ELPGN group, in partnership with the Nordic network for adult learning (NVL), to investigate the possibilities for collaboration between the Nordic countries in developing a number of joint documents on career competences and....../or a competence framework for career learning in the Nordic countries. The objective for this concept note is to contribute to a shared Nordic frame of understanding for career competences which can be used in the ongoing development of guidance in the Nordic countries. The intended audience is guidance...... professionals, teachers, researchers, managers, policy makers and clients....

Canadian safeguards research and development in support of the IAEA program document outlining the various tasks which comprise the program

International Nuclear Information System (INIS)

1985-12-01

Canada has established a safeguards research and development program, the purpose of which is to supplement the resources of the International Atomic Energy Agency. The program of support is a coordinated effort for the development and application of safeguards techniques and instruments to facilities safeguarded by the IAEA. This document sets forth those tasks which comprise the program

Technical basis and evaluation criteria for an air sampling/monitoring program

International Nuclear Information System (INIS)

Gregory, D.C.; Bryan, W.L.; Falter, K.G.

1993-01-01

Air sampling and monitoring programs at DOE facilities need to be reviewed in light of revised requirements and guidance found in, for example, DOE Order 5480.6 (RadCon Manual). Accordingly, the Oak Ridge National Laboratory (ORNL) air monitoring program is being revised and placed on a sound technical basis. A draft technical basis document has been written to establish placement criteria for instruments and to guide the ''retrospective sampling or real-time monitoring'' decision. Facility evaluations are being used to document air sampling/monitoring needs, and instruments are being evaluated in light of these needs. The steps used to develop this program and the technical basis for instrument placement are described

USNRC regulatory guidance for engineered safety feature air cleaning systems

International Nuclear Information System (INIS)

Bellamy, R.R.

1991-01-01

The need for clear, technically appropriate, and easily implementable guidance for the design, testing, and maintenance of nuclear air cleaning systems has long been recognized. Numerous industry consensus standards have been issued and revised over the last 30 years. Guidance has also been published by the US Nuclear Regulatory Commission in the form of regulations, regulatory guides, standard review plans, NUREG documents, and information notices. This paper will summarize the latest revisions to these documents and emphasize Regulatory Guide 1.52, Design, Testing, and Maintenance Criteria for Post-Accident Engineered-Safety-Feature Atmosphere Cleanup System Air Filtration and Adsorption Units of Light-Water-Cooled Nuclear Power Plants, which was last revised in 1978. The USNRC has undertaken a project to revise this regulatory guide, and the status of that revision is highlighted

THE RELIGIOUS GUIDANCE FOR PROSTITUTE A Descriptive Study at Palimanan Cirebon

Directory of Open Access Journals (Sweden)

Murip Yahya

2016-02-01

Full Text Available This study attempts to investigate the implementation of religious guidance for prostitute and its influence to Woman Social Institution Silih Asih in Palimanan, Cirebon. It formulated on four research questions: 1 How is the process of religious guidance in Social Institution Silih Asih; 2 What is the participants’s efforts to achieve the goal of religious guidance; 3 How is the material of religious guidance in Social Institution Silih Asih Palimanan; 4 How is the approach and method of religious guidance applied in Social Institution Silih Asih Palimanan to support and achieve the aim of religious guidance. The study used qualitative-naturalistic, research design with descriptive method. The data were collected through observation, interview, and document analysis. The results of the study show that: 1 there were two stages of religious guidance: identification stage and rehabilitation process; 2 the participants were identified by their age, marital status, education background, parents’ job, and reasons of being prostitute; 3 the materials presented on theoretical and natural materials based on Islam thoughts; 4 the religious guidance used various approaches: experience, habituation, emotional, rational, and holistic.

76 FR 60503 - Guidance for Industry on Target Animal Safety and Effectiveness Protocol Development and...

Science.gov (United States)

2011-09-29

... Safety and Effectiveness Protocol Development and Submission.'' The purpose of this document is to provide sponsors guidance in preparation of study protocols for review by the Center for Veterinary Medicine, Office of New Animal Drug Evaluation. The recommendations included in this guidance are intended...

76 FR 59142 - Guidance for Industry on Reproductive and Developmental Toxicities-Integrating Study Results To...

Science.gov (United States)

2011-09-23

... of study results to assess concerns about human reproductive and developmental toxicities. It does... assist that office in processing your requests. See the SUPPLEMENTARY INFORMATION section for electronic access to the guidance document. Submit electronic comments on the guidance to http://www.regulations.gov...

Make Change Happen at the Program or Institutional Scale: Converting Community Expertise into Practical Guidance

Science.gov (United States)

McDaris, J. R.; Manduca, C. A.; Orr, C. H.

2016-12-01

As geoscience and STEM programs address common challenges like increasing the diversity of graduates or implementing active learning pedagogies, it is important to learn from the experiences of others in the community. Individual faculty members embody a wealth of experience on these topics but distilling that experience into practical guidance that has value for a broad audience is not as simple as knowing exactly what one person did. Context is important, not only because activities used in similar contexts are easier to adapt, but also because activities that work across multiple contexts are more robust. The development of any best practices guidance benefits from the engagement of a community. Synthesizing across multiple viewpoints leads to a consensus that builds on the diversity of individual experiences. The Science Education Resource Center (SERC) at Carleton College has had success generating such resources in geoscience and STEM education. Working with different groups of educators, we have helped develop content around making change happen at the program or institutional levels, increasing the diversity of students graduating in geoscience and STEM, fostering interdisciplinary learning, translating the results of education research into practice, and several others. These resources draw out common practices, situate them in the education research base, and highlight examples of their use in the real world but also communicate the different ways individuals or institutions have adapted these practices for their particular situation. These resources were developed through a group synthesis process involving the contribution of individual or group expertise, a face-to-face meeting of teams working on themes drawn from the contributed work, and asynchronous group revision and review following the meeting. The materials developed via this process provide reliable and adaptable guidance firmly rooted in the community's experience. This presentation will

WIPP documentation plan

International Nuclear Information System (INIS)

Plung, D.L.; Montgomery, T.T.; Glasstetter, S.R.

1986-01-01

In support of the programs at the Waste Isolation Pilot Plant (WIPP), the Publications and Procedures Section developed a documentation plan that provides an integrated document hierarchy; further, this plan affords several unique features: 1) the format for procedures minimizes the writing responsibilities of the technical staff and maximizes use of the writing and editing staff; 2) review cycles have been structured to expedite the processing of documents; and 3) the numbers of documents needed to support the program have been appreciably reduced

Remedial Investigation/Feasibility Study (RI/FS) process, elements and techniques guidance

Energy Technology Data Exchange (ETDEWEB)

1993-12-01

This manual provides detailed guidance on Remedial Investigation/Feasibility Studies (RI/FSs) conducted pursuant to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) at Department of Energy (DOE) facilities. The purpose of the RI/FS, to assess the risk posed by a hazardous waste site and to determine the best way to reduce that risk, and its structure (site characterization, risk assessment, screening and detailed analysis of alternatives, etc.) is defined in the National Oil and Hazardous Substances Pollution Contingency Plan (NCP) and further explained in the Environmental Protection Agency`s (EPA`s) Guidance for Conducting Remedial Investigations and Feasibility Studies Under CERCLA (Interim Final) 540/G-89/004, OSWER Directive 9355.3-01, October 1988. Though issued in 1988, the EPA guidance remains an excellent source of information on the conduct and structure of an RI/FS. This document makes use of supplemental RI/FS-related guidance that EPA has developed since its initial document was issued in 1988, incorporates practical lessons learned in more than 12 years of experience in CERCLA hazardous site remediation, and drawing on those lessons, introduces the Streamlined Approach For Environmental Restoration (SAFER), developed by DOE as a way to proceed quickly and efficiently through the RI/FS process at DOE facilities. Thus as its title implies, this guidance is intended to describe in detail the process and component elements of an RI/FS, as well as techniques to manage the RI/FS effectively.

Magnetic fusion program summary document

International Nuclear Information System (INIS)

1979-04-01

This document outlines the current and planned research, development, and commercialization (RD and C) activities of the Offic of Fusion Energy under the Assistant Secretary for Energy Technology, US Department of Energy (DOE). The purpose of this document is to explain the Office of Fusion Energy's activities to Congress and its committees and to interested members of the public

The Radioactive Waste Management Advisory Committee's. Advice on issues which need to be addressed in the Guidance to be given to the Environment Agencies on the Principles for determining Radioactive Waste Discharge Authorisations - the 'Principles Document'

International Nuclear Information System (INIS)

1998-07-01

In January 1998, the Minister for the Environment, Mr Michael Meacher, informed the Radioactive Waste Management Advisory Committee (RWMAC) that, during the coming year, he would welcome the Committee's advice on proposals for guidance from the Department of the Environment, Transport and the Regions (DETR) to the Environment Agencies on assessment principles for determining radioactive waste discharge authorisations. This will hereafter be referred to as the Principles Document. The RWMAC has provided advice on the process of regulating radioactive waste discharges for many years. A summary of some of this activity is given in Annex 1. As a result, it has been pressing for this Principles Document guidance to be made available since its Twelfth Report in 1991. In response to the Minister's request, the RWMAC offered to assemble and submit early advice on what it believes the guidance needs to cover: this document fulfils that offer. The fundamental purpose of the advice is to help promote clarity of the regulatory regime for the benefit of the regulators themselves who must apply it, the industry to whom it is applied and, most importantly, the public whose safety it is designed to protect. Clarification of a number of aspects of the process is also likely to provide opportunity for efficiency gains. At a subsequent stage, the RWMAC will be happy to provide comment on any draft principles documentation prepared by the DETR. The RWMAC acknowledges that some of the issues it raises in this advice could be taken by others to be either outside the scope of the Principles Document or, by implying a need for more fundamental consideration of the discharge authorisation process, could potentially preclude its early publication. In the first instance, reference to an alternative source of relevant advice might suffice, providing this advice is itself easily accessible and understandable. In the second, the issue itself might be one to be fed into the Government's planned

Documentation of spectrom-32

International Nuclear Information System (INIS)

Callahan, G.D.; Fossum, A.F.; Svalstad, D.K.

1989-01-01

SPECTROM-32 is a finite element program for analyzing two-dimensional and axisymmetric inelastic thermomechanical problems related to the geological disposal of nuclear waste. The code is part of the SPECTROM series of special-purpose computer programs that are being developed by RE/SPEC Inc. to address many unique rock mechanics problems encountered in analyzing radioactive wastes stored in geologic formations. This document presents the theoretical basis for the mathematical models, the finite element formulation and solution procedure of the program, a description of the input data for the program, verification problems, and details about program support and continuing documentation. The computer code documentation is intended to satisfy the requirements and guidelines outlined in the document entitled Final Technical Position on Documentation of Computer Codes for High-Level Waste Management. The principal component models used in the program involve thermoelastic, thermoviscoelastic, thermoelastic-plastic, and thermoviscoplastic types of material behavior. Special material considerations provide for the incorporation of limited-tension material behavior and consideration of jointed material behavior. Numerous program options provide the capabilities for various boundary conditions, sliding interfaces, excavation, backfill, arbitrary initial stresses, multiple material domains, load incrementation, plotting database storage and access of results, and other features unique to the geologic disposal of radioactive wastes. Numerous verification problems that exercise many of the program options and illustrate the required data input and printed results are included in the documentation

Severe accident management guidance for third Qinshan Nuclear Power Plant

International Nuclear Information System (INIS)

Su Changsong

2010-01-01

The paper describes the background, document structure and the summaries of Severe Accident Management Guidance (SAMG) for Third Qinshan Nuclear Power Plant (TQNPP), and also introduces briefly some design features and their impacts on SAMG. (authors)

Environmental restoration and decontamination and decommissioning safety documentation

International Nuclear Information System (INIS)

Hansen, J.L.; Frauenholz, L.H.; Kerr, N.R.

1993-01-01

This document presents recommendations of a working group designated by the Environmental Restoration and Remediation (ER) and Decontamination and Decommissioning (D ampersand D) subcommittees of the Westinghouse M ampersand O (Management and Operation) Nuclear Facility Safety Committee. A commonalty of approach to safety documentation specific to ER and D ampersand D activities was developed and is summarized below. Allowance for interpretative tolerance and documentation flexibility appropriate to the activity, graded for hazard category, duration, and complexity, was a primary consideration in development of this guidance

Guidance document on fat reduction factor, functional barrier concept, phthalates and primary aromatic amines

DEFF Research Database (Denmark)

Hoekstra, Eddo J.; Petersen, Jens Højslev; Bustos, Juana

Commission Regulation (EU) No 10/2011 of 14 January 2011 on plastic materials and articles intended to come into contact with food contains four issues for which food inspectors and enforcement laboratories need further guidance. These issues are the concept of the fat reduction factor...

Implementasi Program Bimbngan dan Konseling

Directory of Open Access Journals (Sweden)

Annas Kamil

2016-10-01

Full Text Available Abstract: Basic tasks the teacher supervisor is compiling the program guidance and counseling, implement the program guidance and counseling, evaluate program implementation guidance and counseling, analysis of the results of the implementation of the guidance and counseling and follow-up program implementation guidance and counseling to learners who becomes his responsibility. In fact guidance and counseling teachers of government senior high schools in Solok Regency did not elaborate on the program guidance and counseling in accordance with the types of services and areas of development without any elaboration time allocation, class of service to be provided, the material will be presented and didn’t have the weekly program of guidance and counseling. This study used a descriptive approach. The population of the research is all of guidance and counseling teachers in government senior high schools in Solok Regency, totally 49 people with sampling techniques namely the sampling area of 32 people. Data collection techniques using question form. The Data were analyzed using percentage technique.

Implementation of NUREG 1318 guidance within the Yucca Mountain Project

International Nuclear Information System (INIS)

La Monica, L.B.; Waddell, J.D.; Hardin, E.L.

1990-01-01

This paper discusses the implementation of a quality assurance program that fulfills the requirements of the U.S. Nuclear Regulatory Commission (NRC). Additional guidance for this program was provided in NUREG 1318, Technical Position on Items and Activities in the High-Level Waste Geologic Repository Program Subject to Quality Assurance Requirements for the identification of items and activities important to public radiological safety and waste isolation for placement on a Q-List and Quality Activities List and also for graded application of QA measures. The process and organization for implementing this guidance is discussed

I and C security program for nuclear facilities: implementation guide - TAFICS/IG/2

International Nuclear Information System (INIS)

2016-04-01

This is the second in a series of documents being developed by TAFICS for protecting computer-based I and C systems of Indian nuclear facilities from cyber attacks. The document provides guidance to nuclear facility management to establish, implement and maintain a robust I and C security program - consisting of security plan and a set of security controls. In order to provide a firm basis for the security program, the document also identifies the fundamental security principles and foundational security requirements related to computer-based I and C systems of nuclear facilities. It is recommended that all applicable Indian nuclear facilities should implement the security program - with required adaptation - so as to provide the necessary assurance that the I and C systems are adequately protected against cyber attacks. (author)

75 FR 17143 - Draft Guidance for Industry and Food and Drug Administration Staff; Medical Devices; Neurological...

Science.gov (United States)

2010-04-05

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2009-D-0495] Draft Guidance for Industry and Food and Drug Administration Staff; Medical Devices; Neurological and Physical Medicine Device Guidance Documents; Availability AGENCY: Food and Drug Administration, HHS. ACTION...

75 FR 44267 - Draft Guidance for Industry and Food and Drug Administration Staff; Medical Devices; Neurological...

Science.gov (United States)

2010-07-28

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2009-N-0495] Draft Guidance for Industry and Food and Drug Administration Staff; Medical Devices; Neurological and Physical Medicine Device Guidance Document; Reopening of Comment Period AGENCY: Food and Drug...

Towards a standardised approach for evaluating guidelines and guidance documents on palliative sedation: study protocol.

Science.gov (United States)

Abarshi, Ebun; Rietjens, Judith; Caraceni, Augusto; Payne, Sheila; Deliens, Luc; Van Den Block, Lieve

2014-01-01

Sedation in palliative care has received growing attention in recent years; and so have guidelines, position statements, and related literature that provide recommendations for its practice. Yet little is known collectively about the content, scope and methodological quality of these materials. According to research, there are large variations in palliative sedation practice, depending on the definition and methodology used. However, a standardised approach to comparing and contrasting related documents, across countries, associations and governmental bodies is lacking. This paper reports on a protocol designed to enable thorough and systematic comparison of guidelines and guidance documents on palliative sedation. A multidisciplinary and international group of palliative care researchers, identified themes and clinical issues on palliative sedation based on expert consultations and evidence drawn from the EAPC (European Association of Palliative Care) framework for palliative sedation and AGREE II (Appraisal Guideline Research and Evaluation) instrument for guideline assessment. The most relevant themes were selected and built into a comprehensive checklist. This was tested on people working closely with practitioners and patients, for user-friendliness and comprehensibility, and modified where necessary. Next, a systematic search was conducted for guidelines in English, Dutch, Flemish, or Italian. The search was performed in multiple databases (PubMed, CancerLit, CNAHL, Cochrane Library, NHS Evidence and Google Scholar), and via other Internet resources. Hereafter, the final version of the checklist will be used to extract data from selected literature, and the same will be compiled, entered into SPSS, cleaned and analysed systematically for publication. We have together developed a comprehensive checklist in a scientifically rigorous manner to allow standardised and systematic comparison. The protocol is applicable to all guidelines on palliative sedation, and

International Scavenging for First Responder Guidance and Tools: IAEA Products

Energy Technology Data Exchange (ETDEWEB)

Stern, W. [Brookhaven National Lab. (BNL), Upton, NY (United States); Berthelot, L. [Brookhaven National Lab. (BNL), Upton, NY (United States); Bachner, K. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2017-05-05

In fiscal years (FY) 2016 and 2017, with support from the U.S. Department of Homeland Security (DHS), Brookhaven National Laboratory (BNL) examined the International Atomic Energy Agency (IAEA) radiological emergency response and preparedness products (guidance and tools) to determine which of these products could be useful to U.S. first responders. The IAEA Incident and Emergency Centre (IEC), which is responsible for emergency preparedness and response, offers a range of tools and guidance documents for responders in recognizing, responding to, and recovering from radiation emergencies and incidents. In order to implement this project, BNL obtained all potentially relevant tools and products produced by the IAEA IEC and analyzed these materials to determine their relevance to first responders in the U.S. Subsequently, BNL organized and hosted a workshop at DHS National Urban Security Technology Laboratory (NUSTL) for U.S. first responders to examine and evaluate IAEA products to consider their applicability to the United States. This report documents and describes the First Responder Product Evaluation Workshop, and provides recommendations on potential steps the U.S. federal government could take to make IAEA guidance and tools useful to U.S. responders.

GUIDANCE FOR NUCLEAR POWER PLANT CONTROL ROOM AND HUMAN-SYSTEM INTERFACE MODERNIZATION

International Nuclear Information System (INIS)

Naser, J.; Morris, G.

2004-01-01

Several nuclear power plants in the United States are starting instrumentation and control (I and C) modernization programs using digital equipment to address obsolescence issues and the need to improve plant performance while maintaining high levels of safety. As an integral part of the I and C modernization program at a nuclear power plant, the control room and other human-system interfaces (HSIs) are also being modernized. To support safe and effective operation, it is critical to plan, design, implement, train for, operate, and maintain the control room and HSI changes to take advantage of human cognitive processing abilities. A project, jointly funded by the Electric Power Research Institute (EPRI) and the United States Department of Energy (DOE) under the Nuclear Energy Plant Optimization (NEPO) Program, is developing guidance for specifying and designing control rooms, remote shut-down panels, HSIs etc. The guidance is intended for application by utilities and suppliers of control room and HSI modernization. The guidance will facilitate specification, design, implementation, operations, maintenance, training, and licensing activities. This guidance will be used to reduce the likelihood of human errors and licensing risk, to gain maximum benefit of implemented technology, and to increase performance. The guidance is of five types. The first is planning guidance to help a utility develop its plant-specific control room operating concepts, its plant-specific endpoint vision for the control room, its migration path to achieve that endpoint vision, and its regulatory, licensing, and human factors program plans. The second is process guidance for general HSI design and integration, human factors engineering analyses, verification and validation, in-service monitoring processes, etc. The third is detailed human factors engineering guidance for control room and HSI technical areas. The fourth is guidance for licensing. The fifth is guidance for special topics

EFSA Panel on Plant Protection Products and their Residues (PPR); EFSA Scientific Opinion on the science behind the revision of the guidance document on dermal absorption

DEFF Research Database (Denmark)

Petersen, Annette

will be finalised and published only after adoption and publication of this opinion. This opinion has been developed after a public consultation of EFSA on the current guidance document and an outsourced project carried out by the UK Chemicals Regulation Directorate (CRD, 2010). It is not intended...... that have an impact on absorption, a description of important elements in the design of experimental studies and an analysis of available data on dermal absorption of PPPs. The PPR Panel concludes that assessment of dermal absorption in the absence of specific studies can be performed based on default...

Guidance on the environmental risk assessment of genetically modified plants

DEFF Research Database (Denmark)

Bartsch, Detlef; Chueca, Cristina; De-Schrijver, Adinda

risk evaluation. The scientific Panel on Genetically Modified Organisms (of the European Food Safety Authority (EFSA GMO Panel) considers seven specific areas of concern to be addressed by applicants and risk assessors during the ERA (1) persistence and invasiveness of the GM plant , or its compatible......This document provides guidance for the environmental risk assessment (ERA) of genetically modified (GM) plants submitted within the framework of Regulation (EC) No. 1829/2003 on GM food and feed or under Directive 2001/18/EC on the deliberate release into the environment of genetically modified...... organisms (GMOs). This document provides guidance for assessing potential effects of GM plants on the environment and the rationales for the data requirements for a comprehensive ERA of GM plants. The ERA should be carried out on a case-by-case basis, following a step-by-step assessment approach...

WCATS: Waste Documentation, Course No. 8504

Energy Technology Data Exchange (ETDEWEB)

Simpson, Sandy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-04-14

This course was developed for individuals at Los Alamos National Laboratory (LANL) who characterize and document waste streams in the Waste Compliance and Tracking System (WCATS) according to Environmental Protection Agency (EPA) Department of Transportation (DOT) regulations, Department of Energy Orders, and other applicable criteria. When you have completed this course, you will be able to recognize how waste documentation enables LANL to characterize and classify hazardous waste for compliant treatment, storage, and disposal, identify the purpose of the waste stream profile (WSP), identify the agencies that provide guidance for waste management, and more.

Safety of magnetic fusion facilities: Volume 2, Guidance

International Nuclear Information System (INIS)

1995-01-01

This document provides guidance for the implementation of the requirements identified in Vol. 1 of this Standard. This guidance is intended for the managers, designers, operators, and other personnel with safety responsibilities for facilities designated as magnetic fusion facilities. While Vol. 1 is generally applicable in that requirements there apply to a wide range of fusion facilities, this volume is concerned mainly with large facilities such as the International Thermonuclear Experimental Reactor (ITER). Using a risk-based prioritization, the concepts presented here may also be applied to other magnetic fusion facilities. This volume is oriented toward regulation in the Department of Energy (DOE) environment

Ethics of clinician communication in a changing communication landscape: guidance from professional societies.

Science.gov (United States)

Gollust, Sarah E; Dwyer, Anne M

2013-12-01

Cancer experts engage in public communication whenever they promote their research or practice, respond to media inquiries, or use social media. In a changing communication landscape characterized by new technologies and heightened attention to cancer controversies, these activities may pose ethical challenges. This study was designed to evaluate existing resources to help clinicians navigate their public communication activities. We conducted a systematic, qualitative content analysis of codes of ethics, policy statements, and similar documents disseminated by professional medical and nursing societies for their members. We examined these documents for four types of content related to public communication: communication via traditional media; communication via social media; other communication to the public, policy, and legal spheres; and nonspecific language regarding public communication. We identified 46 documents from 23 professional societies for analysis. Five societies had language about traditional news media communication, five had guidance about social media, 11 had guidance about other communication domains, and 15 societies offered general language about public communication. The limited existing guidance focused on ethical issues related to patients (such as privacy violations) or clinicians (such as accuracy and professional boundaries), with less attention to population or policy impact of communication. Cancer-related professional societies might consider establishing more specific guidance for clinicians concerning their communication activities in light of changes to the communication landscape. Additional research is warranted to understand the extent to which clinicians face ethical challenges in public communication.

The Hanford Site Environmental Restoration Program 1993 fiscal year work plan

International Nuclear Information System (INIS)

1992-09-01

Site Management System (SMS) guidance requires a Fiscal Year Work Plan (FYWP) be prepared for the Environmental Restoration (ER) Mission Area and all related programs. This document describes the overall ER Mission Area and provides FYWP appendixes for each of the five program areas: Remedial Action (RA); Decontamination and Decommissioning (D ampersand D); Project Management and Support (PM ampersand S); Surveillance and Maintenance (S ampersand M); and Treatment, Storage, and/or Disposal (TSD)

Assessment of Dermatoglyphics Multiple Intelligence Test (DMIT Reports: Implication to Career Guidance Program Enhancement of Academic Institutions

Directory of Open Access Journals (Sweden)

Dr. Maria Luisa A. Valdez

2014-04-01

Full Text Available This research aims to assess the reports generated from the Dermatoglyphics Multiple Intelligence Test (DMIT administered by selected DMIT resource companies and consultancy firms in India with the end view of identifying its implication to career guidance program enhancement of academic institutions. This paper employed the descriptive research method which involved the use of documentary analysis, questionnaires and interviews with purposively selected respondents supported by the researchers’ analysis and insights with reference to the content of the data. Findings of this research revealed that the dermatoglyphics, as a scientific discipline, began with the publication of Purkinje’s thesis (1823 and Galton’s classic book, Fingerprints (1892; DMIT is a remarkable offshoot of Howard Gardner’s Theory of Multiple Intelligences which has the following salient features: Overview of the Dermatoglyphics and the Dermatoglyphics Multiple Intelligence Test/Analysis; Personality Assessment; Profile based on Gardner’s Multiple Intelligences and Dunn’s Brain Lateralization Theories; Learning Styles; Competency and Compatibility Profiles; Working Style; Leadership Style; Management Style; Report Interpretation; and Customized Academic and Relationship Advises; the respondents of this study gave their perceptions with reference to the beneficial results of the DMIT; and the foregoing findings have some implications that may be used by academic institutions to enhance their career guidance program.

75 FR 29768 - Guidance for Industry: Revised Preventive Measures to Reduce the Possible Risk of Transmission of...

Science.gov (United States)

2010-05-27

... manufacturers of plasma derivatives with comprehensive FDA recommendations intended to minimize the possible...CJD) by Blood and Blood Products''' dated August 2006 (2006 draft guidance). DATES: Submit electronic... the SUPPLEMENTARY INFORMATION section for electronic access to the guidance document. Submit...

Report 6: Guidance document. Man-made hazards and Accidental Aircraft Crash hazards modelling and implementation in extended PSA

International Nuclear Information System (INIS)

Kahia, S.; Brinkman, H.; Bareith, A.; Siklossy, T.; Vinot, T.; Mateescu, T.; Espargilliere, J.; Burgazzi, L.; Ivanov, I.; Bogdanov, D.; Groudev, P.; Ostapchuk, S.; Zhabin, O.; Stojka, T.; Alzbutas, R.; Kumar, M.; Nitoi, M.; Farcasiu, M.; Borysiewicz, M.; Kowal, K.; Potempski, S.

2016-01-01

The goal of this report is to provide guidance on practices to model man-made hazards (mainly external fires and explosions) and accidental aircraft crash hazards and implement them in extended Level 1 PSA. This report is a joint deliverable of work package 21 (WP21) and work package 22 (WP22). The general objective of WP21 is to provide guidance on all of the individual hazards selected at the first ASAMPSA-E End Users Workshop (May 2014, Uppsala, Sweden). The objective of WP22 is to provide the solutions for purposes of different parts of man-made hazards Level 1 PSA fulfilment. This guidance is focusing on man-made hazards, namely: external fires and explosions, and accidental aircraft crash hazards. Guidance developed refers to existing guidance whenever possible. The initial part of guidance (WP21 part) reflects current practices to assess the frequencies for each type of hazards or combination of hazards (including correlated hazards) as initiating event for PSAs. The sources and quality of hazard data, the elements of hazard assessment methodologies and relevant examples are discussed. Classification and criteria to properly assess hazard combinations as well as examples and methods for assessment of these combinations are included in this guidance. In appendixes additional material is presented with the examples of practical approaches to aircraft crash and man-made hazard. The following issues are addressed: 1) Hazard assessment methodologies, including issues related to hazard combinations. 2) Modelling equipment of safety related SSC, 3) HRA, 4) Emergency response, 5) Multi-unit issues. Recommendations and also limitations, gaps identified in the existing methodologies and a list of open issues are included. At all stages of this guidance and especially from an industrial end-user perspective, one must keep in mind that the development of man-made hazards probabilistic analysis must be conditioned to the ability to ultimately obtain a representative risk

An ultraviolet-visible spectrophotometer automation system. Part 3: Program documentation

Science.gov (United States)

Roth, G. S.; Teuschler, J. M.; Budde, W. L.

1982-07-01

The Ultraviolet-Visible Spectrophotometer (UVVIS) automation system accomplishes 'on-line' spectrophotometric quality assurance determinations, report generations, plot generations and data reduction for chlorophyll or color analysis. This system also has the capability to process manually entered data for the analysis of chlorophyll or color. For each program of the UVVIS system, this document contains a program description, flowchart, variable dictionary, code listing, and symbol cross-reference table. Also included are descriptions of file structures and of routines common to all automated analyses. The programs are written in Data General extended BASIC, Revision 4.3, under the RDOS operating systems, Revision 6.2. The BASIC code has been enhanced for real-time data acquisition, which is accomplished by CALLS to assembly language subroutines. Two other related publications are 'An Ultraviolet-Visible Spectrophotometer Automation System - Part I Functional Specifications,' and 'An Ultraviolet-Visible Spectrophotometer Automation System - Part II User's Guide.'

Office of Legacy Management. Information and Records Management. Transition Guidance

International Nuclear Information System (INIS)

2004-01-01

The Office of Legacy Management (LM) is an integral part of the U.S. Department of Energy's (DOE's) strategy to ensure that legacy liabilities of former nuclear weapons production sites are properly managed following the completion of environmental cleanup activities. LM will work with each site using an integrated team approach to ensure a successful transition. Part of this process will include transition of Government records and information. The Office of Legacy Management Information and Records Management Transition Guidance focuses on LM's goal to preserve and protect legacy records and information. This guidance document establishes a framework for the transfer of records management responsibilities for sites transferring to LM. It describes the requirements, responsibilities, and procedures for the efficient and cost-effective transfer of custody, ownership, and management of records and other information products from the transfer site to LM. Records management practices are critical to the functions of Federal agencies because records provide information about, or evidence of, the organization, functions, policies, decisions, procedures, operations, or other activities. Therefore, the information generated by an agency is created, maintained, and dispositioned through records management processes that ensure the appropriate preservation and retrieval of essential information. Because of their intrinsic value, best practices to preserve information and records should be utilized when records are transferred from one organization to another. As the transfer program completes cleanup activities at closure sites, a transitional process will facilitate the transparent shift in the management of site records activities to LM. The roles and responsibilities of the transfer site and/or program and LM described in this document are a necessary foundation for cooperation and coordination and are essential to the successful transition of records and information

Office of Legacy Management. Information and Records Management. Transition Guidance

Energy Technology Data Exchange (ETDEWEB)

None

2004-03-01

The Office of Legacy Management (LM) is an integral part of the U.S. Department of Energy’s (DOE’s) strategy to ensure that legacy liabilities of former nuclear weapons production sites are properly managed following the completion of environmental cleanup activities. LM will work with each site using an integrated team approach to ensure a successful transition. Part of this process will include transition of Government records and information. The Office of Legacy Management Information and Records Management Transition Guidance focuses on LM’s goal to preserve and protect legacy records and information. This guidance document establishes a framework for the transfer of records management responsibilities for sites transferring to LM. It describes the requirements, responsibilities, and procedures for the efficient and cost-effective transfer of custody, ownership, and management of records and other information products from the transfer site to LM. Records management practices are critical to the functions of Federal agencies because records provide information about, or evidence of, the organization, functions, policies, decisions, procedures, operations, or other activities. Therefore, the information generated by an agency is created, maintained, and dispositioned through records management processes that ensure the appropriate preservation and retrieval of essential information. Because of their intrinsic value, best practices to preserve information and records should be utilized when records are transferred from one organization to another. As the transfer program completes cleanup activities at closure sites, a transitional process will facilitate the transparent shift in the management of site records activities to LM. The roles and responsibilities of the transfer site and/or program and LM described in this document are a necessary foundation for cooperation and coordination and are essential to the successful transition of records and

Remedial design and remedial action guidance for the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1993-10-01

The US Department of Energy, Idaho Operations Office (DOE-ID), the US Environmental Protection Agency, Region X (EPA), and the Idaho Department of Health and Welfare (IDHW) have developed this guidance on the remedial design and remedial action (RD/RA) process. This guidance is applicable to activities conducted under the Idaho National Engineering Laboratory (INEL) Federal Facility Agreement and Consent Order (FFA/CO) and Action Plan. The INEL FFA/CO and Action Plan provides the framework for performing environmental restoration according to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). The guidance is intended for use by the DOE-ID, the EPA, and the IDHW Waste Area Group (WAG) managers and others involved in the planning and implementation of CERCLA environmental restoration activities. The scope of the guidance includes the RD/RA strategy for INEL environmental restoration projects and the approach to development and review of RD/RA documentation. Chapter 2 discusses the general process, roles and responsibilities, and other elements that define the RD/RA strategy. Chapters 3 through 7 describe the RD/RA documents identified in the FFA/CO and Action Plan. Chapter 8 provides examples of how this guidance can be applied to restoration projects. Appendices are included that provide excerpts from the FFA/CO pertinent to RD/RA (Appendix A), a applicable US Department of Energy (DOE) orders (Appendix B), and an EPA Engineering ''Data Gaps in Remedial Design'' (Appendix C)

Technical Document on Control of Nitrogen Oxides From Municipal Waste Combustors

Science.gov (United States)

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Development of software to provide practical guidance in the managing of a radiological emergency

International Nuclear Information System (INIS)

Ferreira Filho, Alfredo L.; Lima, Fernando R.A.; Loureiro, Eduardo C.M.

2008-01-01

One of the most important aspects of managing a radiological emergency is the ability to promptly and adequately determine and take actions to protect members of public and emergency workers. This work brings up to date a computer software program in Delphi, with the tools, generic procedures and the data necessary to support the Incident Commander, the Radiological Assessor and other members of a generic response organization in case of radiological accident. The aim is also to provide practical guidance for the first responders who will respond during the first few hours to a radiological emergency and for the national officials who would support this early response. Software is now based on the Manual for First Responders to a Radiological Emergency (EPR-First Responders), published in 2006 as part of the IAEA Emergency Preparedness and Response Series, as well as in the IAEA technical document, Generic Procedures for Assessment and Response during a Radiological Emergency, the IAEA-TECDOC-1162, taking account of the lessons learned from using this last document in the area of early response and first responders' actions. The proposed procedures provide action criteria that are clear, concise and predetermined, based on the present knowledge and the accumulated experiences, allowing the immediate decision-making. The objective is to provide, through a portable computer, practical guidance, in the form of action guides, instructions, and supporting data for emergency response that, if implemented, will provide a basic assessment and the response capability needed to protect public and workers in case of different types of radiological emergencies. In addition to appropriate protective action recommendations, it will also provide, when it is necessary, general guidance on the recovery of radioactive sources and initial cleanup operations. The philosophy is to keep the process simple and fast, yet effective. Software is available in Spanish, English and Portuguese

RECON: a computer program for analyzing repository economics. Documentation and user's manual

International Nuclear Information System (INIS)

Clark, L.L.; Cole, B.M.; McNair, G.W.; Schutz, M.E.

1983-05-01

From 1981 through 1983 the Pacific Northwest Laboratory has been developing a computer model named RECON to calculate repository costs from parametric data input. The objective of the program has been to develop the capability to evalute the effect on costs of changes in repository design parameters and operating scenario assumptions. This report documents the development of the model through March of 1983. Included in the report are: (1) descriptions of model development and the underlying equations, assumptions and definitions; (2) descriptions of data input either using card images or an interactive data input program; and (3) detailed listings of the program and definitions of program variables. Cost estimates generated using the model have been verified against independent estimates and good agreement has been obtained

EFSA Panel on Dietetic Products, Nutrition and Allergies (NDA) ; Guidance on the scientific requirements for health claims related to physical performance

DEFF Research Database (Denmark)

Tetens, Inge

The Panel on Dietetic Products, Nutrition and Allergies (NDA) was asked by the European Food Safety Authority (EFSA) to draft guidance on scientific requirements for health claims related to physical performance. This guidance has been drawn from scientific opinions of the NDA Panel on such health...... claims. Thus, this guidance document represents the views of the NDA Panel based on the experience gained to date with the evaluation of health claims in this area. It is not intended that the document should include an exhaustive list of beneficial effects and studies/outcome measures which...

78 FR 34392 - Guidance for Industry and Food and Drug Administration Staff: Technical Considerations for Pen...

Science.gov (United States)

2013-06-07

... adhesive label to assist the office in processing your requests. The guidance may also be obtained by mail... and Drug Administration, 5630 Fishers Lane, Rm. 1061, Rockville, MD 20852. FOR FURTHER INFORMATION... June 2013. FDA is providing this final guidance document to assist industry in developing technical and...

Hanford Site waste minimization and pollution prevention awareness program plan

International Nuclear Information System (INIS)

Place, B.G.

1998-01-01

This plan, which is required by US Department of Energy (DOE) Order 5400. 1, provides waste minimization and pollution prevention guidance for all Hanford Site contractors. The plan is primary in a hierarchical series that includes the Hanford Site Waste Minimization and Pollution Prevention Awareness Program Plan, Prime contractor implementation plans, and the Hanford Site Guide for Preparing and Maintaining Generator Group Pollution Prevention Program Documentation (DOE-RL, 1997a) describing programs required by Resource Conservation and Recovery Act of 1976 (RCRA) 3002(b) and 3005(h) (RCRA and EPA, 1994). Items discussed include the pollution prevention policy and regulatory background, organizational structure, the major objectives and goals of Hanford Site's pollution prevention program, and an itemized description of the Hanford Site pollution prevention program. The document also includes US Department of Energy, Richland Operations Office's (RL's) statement of policy on pollution prevention as well as a listing of regulatory drivers that require a pollution prevention program

In Respect to the Cognitive Load Theory: Adjusting Instructional Guidance with Student Expertise.

Science.gov (United States)

Schilling, Jim

2017-01-01

The amount of guidance supplied by educators to students in allied health programs is a factor in student learning. According to the cognitive load theory of learning, without adequate instructional support, novice learners will be overwhelmed and unable to store information, while unnecessary guidance supplied to advanced students will cause extraneous cognitive load on the working memory system. Adjusting instructional guidance for students according to their level of expertise to minimize extraneous cognitive load and optimize working memory storage capacity will enhance learning effectiveness. Novice students presented with complex subject matter require significant guidance during the initial stages, using strategies such as worked examples. As students comprehend information, instructional guidance needs to gradually fade to avoid elevated extraneous cognitive load from the expertise reversal effect. An instructional strategy that utilizes a systemic (fixed) or adjustable (adaptive) tapering of guidance to students in allied health programs depending on their expertise will optimize learning capability.

Software documentation for TRU certification program

International Nuclear Information System (INIS)

CLINTON, R.

1999-01-01

The document provides validation information for software used to support TRU operational activities. Calculations were performed using a spreadsheet application. This document provides information about the usage of the software application, Microsoft(reg s ign) Excel. Microsoft(reg s ign) Excel spreadsheets were used to perform specific calculations to determine the amount of containers to visually examine and to perform analyses on container head-gas data. Contained in this document are definitions of formulas and variables with relation to the Excel codes used. Also, a demonstration is provided using predetermined values to obtain predetermined results

76 FR 570 - Draft Guidance for Industry and Food and Drug Administration Staff; Establishing the Performance...

Science.gov (United States)

2011-01-05

... electronic or written comments on the draft guidance by April 5, 2011. ADDRESSES: Submit written requests for... INFORMATION section for information on electronic access to the guidance. Submit electronic comments on the..., plasma, and blood. These devices are used to aid in the diagnosis of Lyme disease. This document does not...

Navigation and flight director guidance for the NASA/FAA helicopter MLS curved approach flight test program

Science.gov (United States)

Phatak, A. V.; Lee, M. G.

1985-01-01

The navigation and flight director guidance systems implemented in the NASA/FAA helicopter microwave landing system (MLS) curved approach flight test program is described. Flight test were conducted at the U.S. Navy's Crows Landing facility, using the NASA Ames UH-lH helicopter equipped with the V/STOLAND avionics system. The purpose of these tests was to investigate the feasibility of flying complex, curved and descending approaches to a landing using MLS flight director guidance. A description of the navigation aids used, the avionics system, cockpit instrumentation and on-board navigation equipment used for the flight test is provided. Three generic reference flight paths were developed and flown during the test. They were as follows: U-Turn, S-turn and Straight-In flight profiles. These profiles and their geometries are described in detail. A 3-cue flight director was implemented on the helicopter. A description of the formulation and implementation of the flight director laws is also presented. Performance data and analysis is presented for one pilot conducting the flight director approaches.

TRU Waste Management Program. Cost/schedule optimization analysis

International Nuclear Information System (INIS)

Detamore, J.A.; Raudenbush, M.H.; Wolaver, R.W.; Hastings, G.A.

1985-10-01

This Current Year Work Plan presents in detail a description of the activities to be performed by the Joint Integration Office Rockwell International (JIO/RI) during FY86. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO/RI by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO/RI tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance development, task monitoring, task progress information gathering and reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, and preparation of reports for DOE detailing program status. Program Analysis is performed by the JIO/RI to support identification and assessment of alternatives, and development of long-term TRU waste program capabilities. These analyses include short-term analyses in response to DOE information requests, along with performing an RH Cost/Schedule Optimization report. Systems models will be developed, updated, and upgraded as needed to enhance JIO/RI's capability to evaluate the adequacy of program efforts in various fields. A TRU program data base will be maintained and updated to provide DOE with timely responses to inventory related questions

Safeguards-by-Design: Guidance for Independent Spent Fuel Dry Storage Installations (ISFSI)

Energy Technology Data Exchange (ETDEWEB)

Trond Bjornard; Philip C. Durst

2012-05-01

This document summarizes the requirements and best practices for implementing international nuclear safeguards at independent spent fuel storage installations (ISFSIs), also known as Away-from- Reactor (AFR) storage facilities. These installations may provide wet or dry storage of spent fuel, although the safeguards guidance herein focuses on dry storage facilities. In principle, the safeguards guidance applies to both wet and dry storage. The reason for focusing on dry independent spent fuel storage installations is that this is one of the fastest growing nuclear installations worldwide. Independent spent fuel storage installations are typically outside of the safeguards nuclear material balance area (MBA) of the reactor. They may be located on the reactor site, but are generally considered by the International Atomic Energy Agency (IAEA) and the State Regulator/SSAC to be a separate facility. The need for this guidance is becoming increasingly urgent as more and more nuclear power plants move their spent fuel from resident spent fuel ponds to independent spent fuel storage installations. The safeguards requirements and best practices described herein are also relevant to the design and construction of regional independent spent fuel storage installations that nuclear power plant operators are starting to consider in the absence of a national long-term geological spent fuel repository. The following document has been prepared in support of two of the three foundational pillars for implementing Safeguards-by-Design (SBD). These are: i) defining the relevant safeguards requirements, and ii) defining the best practices for meeting the requirements. This document was prepared with the design of the latest independent dry spent fuel storage installations in mind and was prepared specifically as an aid for designers of commercial nuclear facilities to help them understand the relevant international requirements that follow from a country’s safeguards agreement with

76 FR 28688 - Draft Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls...

Science.gov (United States)

2011-05-18

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration 21 CFR Part 866 [Docket No. FDA-2011-D-0102] Draft Guidance for Industry and Food and Drug Administration Staff; Class II Special Controls Guidance Document: In Vitro Diagnostic Devices for Bacillus Species Detection AGENCY: Food and...

75 FR 14445 - Guidance for Industry on Submitting a Report for Multiple Facilities to the Reportable Food...

Science.gov (United States)

2010-03-25

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2009-D-0260] Guidance for Industry on Submitting a Report for Multiple Facilities to the Reportable Food Electronic... Act of 2007.'' The document provides guidance to the industry in complying with the Reportable Food...

76 FR 22905 - Guidance for Food and Drug Administration Staff and Tobacco Retailers on Civil Money Penalties...

Science.gov (United States)

2011-04-25

...] Guidance for Food and Drug Administration Staff and Tobacco Retailers on Civil Money Penalties and No... entitled ``Civil Money Penalties and No- Tobacco-Sale Orders for Tobacco Retailers.'' This guidance document describes FDA's current policies with respect to civil money penalties and no-tobacco-sale orders...

Silica dust control in small-scale building/structure demolition operations using good work practice guidance

International Nuclear Information System (INIS)

Muianga, C V; Rice, C H; Succop, P

2009-01-01

Work practices can influence exposure, especially in small-scale operations conducted by mobile work crews. This study evaluated the use of information on good work practice in control guidance sheets adapted from UK Silica Essentials guidance sheets by trained workers and supervisors employed in small-scale concrete and masonry demolition operations. A one-page employee silica task-based control guidance sheet for each of four demolition tasks and multiple-page silica control guidance for supervisors were developed. Interactive, hands-on worker training on these task-based good work practice controls was developed. Training was presented to 26 participants from two demolition crews. Feedback on the training and task-based good work practice control guidance sheets was elicited. Observations of work practices were made before and after training. Participants indicated gains in knowledge and checklists were used to document skill attainment. The quality of the training and usefulness of the material/skills was rated high by trainees. Increased use of water to suppress dust and wet cleaning methods on the job were documented following the training. Additional follow-up after training is required to determine long-term impact on sustained changes in work practices, and to evaluate the need for refresher training.

Silica dust control in small-scale building/structure demolition operations using good work practice guidance

Science.gov (United States)

Muianga, C. V.; Rice, C. H.; Succop, P.

2009-02-01

Work practices can influence exposure, especially in small-scale operations conducted by mobile work crews. This study evaluated the use of information on good work practice in control guidance sheets adapted from UK Silica Essentials guidance sheets by trained workers and supervisors employed in small-scale concrete and masonry demolition operations. A one-page employee silica task-based control guidance sheet for each of four demolition tasks and multiple-page silica control guidance for supervisors were developed. Interactive, hands-on worker training on these task-based good work practice controls was developed. Training was presented to 26 participants from two demolition crews. Feedback on the training and task-based good work practice control guidance sheets was elicited. Observations of work practices were made before and after training. Participants indicated gains in knowledge and checklists were used to document skill attainment. The quality of the training and usefulness of the material/skills was rated high by trainees. Increased use of water to suppress dust and wet cleaning methods on the job were documented following the training. Additional follow-up after training is required to determine long-term impact on sustained changes in work practices, and to evaluate the need for refresher training.

Unified State Plan for Guidance, Counseling and Placement in Colorado. Grades K-6.

Science.gov (United States)

Terrill, Jerry; And Others

This guide, one of three units in the Colorado state plan for guidance program development, is written for educators as both a guideline and a needs assessment instrument to assist in the identification of deficit areas in school guidance programs. In a beginning section, this unit for the elementary years provides a brief philosophy of elementary…

Documentation of spectrom-41

International Nuclear Information System (INIS)

Svalstad, D.K.

1989-01-01

SPECTROM-41 is a finite element heat transfer computer program developed to analyze thermal problems related to nuclear waste disposal. The code is part of the SPECTROM (Special Purpose Engineering Codes for Thermal/ROck Mechanics) series of special purpose finite element programs that are continually being developed by RE/SPEC Inc. (RSI) to address the many unique formations. This document presents the theoretical basis for the mathematical model, the finite element formulation of the program, and a description of the input data for the program, along with details about program support and continuing documentation. The documentation is intended to satisfy the requirements and guidelines outlined in NUREG-0856. The principal component model used in the programs based on Fourier's law of conductance. Numerous program options provide the capability of considering various boundary conditions, material stratification and anisotropy, and time-dependent heat generation that are characteristic of problems involving the disposal of nuclear waste in geologic formation. Numerous verification problems are included in the documentation in addition to highlights of past and ongoing verification and validation efforts. A typical repository problem is solving using SPECTROM-41 to demonstrate the use of the program in addressing problems related to the disposal of nuclear waste

HANDBOOK: GUIDANCE ON SETTING PERMIT CONDITIONS AND REPORTING TRIAL BURN RESULTS

Science.gov (United States)

This Handbook provides guidance for establishing operational conditions for incinerators. he document provides a means for state and local agencies to achieve a level of consistency in setting permit conditions that will result in establishment of more uniform permit conditions n...

WHO Regional Office for Europe guidance for influenza surveillance in humans.

NARCIS (Netherlands)

Brown, C.S.; Andraghetti, R.; Paget, J.

2009-01-01

Recent international mandates, and the emergent circulation of pandemic (H1N1) 2009 virus in human populations, call for strengthening influenza surveillance to better target seasonal influenza control programmes and support pandemic preparedness. This document provides technical guidance to

Guidance system operations plan for manned cm earth orbital and lunar missions using program Colossus 3. Section 2: Data links

Science.gov (United States)

Hamilton, M. H.

1971-01-01

The data links for use with the guidance system operations plan for manned command module earth orbital and lunar missions using program Colossus 3 are presented. The subjects discussed are: (1) digital uplink to CMC, (2) command module contiguous block update, (3) CMC retrofire external data update, (4) CMC digital downlink, and (5) CMC entry update.

LLNL Waste Minimization Program Plan

International Nuclear Information System (INIS)

1990-05-01

This document is the February 14, 1990 version of the LLNL Waste Minimization Program Plan (WMPP). Now legislation at the federal level is being introduced. Passage will result in new EPA regulations and also DOE orders. At the state level the Hazardous Waste Reduction and Management Review Act of 1989 was signed by the Governor. DHS is currently promulgating regulations to implement the new law. EPA has issued a proposed new policy statement on source reduction and recycling. This policy reflects a preventative strategy to reduce or eliminate the generation of environmentally-harmful pollutants which may be released to the air, land surface, water, or ground water. In accordance with this policy new guidance to hazardous waste generators on the elements of a Waste Minimization Program was issued. This WMPP is formatted to meet the current DOE guidance outlines. The current WMPP will be revised to reflect all of these proposed changes when guidelines are established. Updates, changes and revisions to the overall LLNL WMPP will be made as appropriate to reflect ever-changing regulatory requirements

Building America Guidance for Identifying and Overcoming Code, Standard, and Rating Method Barriers

Energy Technology Data Exchange (ETDEWEB)

Cole, Pamala C.; Halverson, Mark A.

2013-09-01

The U.S. Department of Energy’s (DOE) Building America program implemented a new Codes and Standards Innovation (CSI) Team in 2013. The Team’s mission is to assist Building America (BA) research teams and partners in identifying and resolving conflicts between Building America innovations and the various codes and standards that govern the construction of residences. A CSI Roadmap was completed in September, 2013. This guidance document was prepared using the information in the CSI Roadmap to provide BA research teams and partners with specific information and approaches to identifying and overcoming potential barriers to Building America (BA) innovations arising in and/or stemming from codes, standards, and rating methods. For more information on the BA CSI team, please email: CSITeam@pnnl.gov

Vocational guidance in social volunteering

Directory of Open Access Journals (Sweden)

Nikolay S. Pryazhnikov

2017-03-01

Full Text Available The paper discusses the possibilities and limitations of vocational guidance in the social volunteering system. The essence of volunteer work is closely related with assistance to desperate people in searching for the meaning of living, often coinciding with labour activity that are deemed in terms of “the main matter of life” and “the leading activity”. For adolescents, it is the choice of career, and for adults, it is the work proper (i.e. an essential condition for personal self-realization. The problem of “forced volunteering” for experts in vocational guidance also means that they often have to work voluntarily and unselfishly outside the official guidelines. To clarify the terms «volunteer» and «a person in desperate need of help» the study used the method of analyzing the documents, e.g. the Regulations on Social Volunteering, the generalization of psychological sources, the initial survey of university students as active supporters of the volunteer movement, On the essence of volunteering and the place of career guidance in selfless social work. Vocational guidance is not excluded from the general system of volunteerism, but has an insufficiently defined status and low popularity among participants in social volunteering. Also, the problem of «forced volunteering» of experts in career counseling, which often requires voluntary and unselfish performance of quality work outside the framework of official instructions, is also indicated. Simultaneously, positive aspects of such disinterested career initiatives are noted, in particular, less control by the official inspectors (or customers and, accordingly, greater freedom of creativity than when someone else does the work.

Development of guidance for preparing treatability variance petitions from the RCRA Land Disposal Restrictions for DOE [Department of Energy] mixed-waste streams

International Nuclear Information System (INIS)

Harms, T.; Scheuer, N.; Martin, R.; Van Epp, T.; Triplett, M.

1990-01-01

In response to the Department of Energy's (DOE) anticipated need for variances from the Resource Conservation and Recovery Act (RCRA) Land Disposal Restriction (LDR) treatment requirements, a treatability variance guidance document is being prepared for use by DOE facilities and operations offices. The guidance document, although applicable to non-mixed hazardous waste streams, provides specific guidance regarding radioactive mixed-waste streams. Preparation of the guidance manual has involved developing an overview of the Land Disposal Restrictions, as well as an overview of the petition preparation process. The DOE internal review requirements are specifically addressed in the manual. Specific data requirements and engineering analyses are also described. A discussion of EPA's criteria for granting a treatability variance is also provided. A checklist for completeness of the petition is provided. Model language for use in DOE treatability variance petitions will be provided in a petition for a DOE waste stream as an appendix to the document

Advanced alarm system design and human performance: Guidance development and current research

Energy Technology Data Exchange (ETDEWEB)

O` Hara, J M [Brookhaven National Lab., Upton, NY (United States)

1997-09-01

This paper describes a research program sponsored by the U.S. Nuclear Regulatory Commission to address the human factors engineering (HFE) aspects of nuclear power plant alarm systems. The overall objective of the program is to develop HFE review guidance for advanced alarm systems. Guidance has been developed based on a broad base of technical and research literature. As part of the development effort, aspects of alarm system design for which the technical basis was insufficient to support guidance development were identified and prioritized. Research is currently underway to address the highest priority topics: alarm processing and display characteristics. (author). 29 refs, 2 figs.

Advanced alarm system design and human performance: Guidance development and current research

International Nuclear Information System (INIS)

O'Hara, J.M.

1997-01-01

This paper describes a research program sponsored by the U.S. Nuclear Regulatory Commission to address the human factors engineering (HFE) aspects of nuclear power plant alarm systems. The overall objective of the program is to develop HFE review guidance for advanced alarm systems. Guidance has been developed based on a broad base of technical and research literature. As part of the development effort, aspects of alarm system design for which the technical basis was insufficient to support guidance development were identified and prioritized. Research is currently underway to address the highest priority topics: alarm processing and display characteristics. (author). 29 refs, 2 figs

Multi-Function Waste Tank Facility Quality Assurance Program Plan, Project W-236A. Revision 2

Energy Technology Data Exchange (ETDEWEB)

Hall, L.R.

1995-05-30

This document describes the Quality Assurance (QA) program for the Multi-Function Waste Tank Facility (MWTF) Project. The purpose of this QA program is to control project activities in such a manner as to achieve the mission of the MWTF Project in a safe and reliable manner. The QA program for the MWTF Project is founded on DOE Order 5700.6C, Quality Assurance, and implemented through the use of ASME NQA-1, Quality Assurance Program Requirements for Nuclear Facilities (ASME 1989 with addenda la-1989, lb-1991 and lc-1992). This document describes the program and planned actions which the Westinghouse Hanford Company (WHC) will implement to demonstrate and ensure that the project meets the requirements of DOE Order 5700.6C through the interpretive guidance of ASME NQA-1.

Multi-Function Waste Tank Facility Quality Assurance Program Plan, Project W-236A. Revision 2

International Nuclear Information System (INIS)

Hall, L.R.

1995-01-01

This document describes the Quality Assurance (QA) program for the Multi-Function Waste Tank Facility (MWTF) Project. The purpose of this QA program is to control project activities in such a manner as to achieve the mission of the MWTF Project in a safe and reliable manner. The QA program for the MWTF Project is founded on DOE Order 5700.6C, Quality Assurance, and implemented through the use of ASME NQA-1, Quality Assurance Program Requirements for Nuclear Facilities (ASME 1989 with addenda la-1989, lb-1991 and lc-1992). This document describes the program and planned actions which the Westinghouse Hanford Company (WHC) will implement to demonstrate and ensure that the project meets the requirements of DOE Order 5700.6C through the interpretive guidance of ASME NQA-1

Sampling quality assurance guidance in support of EM environmental sampling and analysis activities

International Nuclear Information System (INIS)

1994-05-01

This document introduces quality assurance guidance pertaining to the design and implementation of sampling procedures and processes for collecting environmental data for DOE's Office of EM (Environmental Restoration and Waste Management)

Hanford Site Environmental Restoration Program 1994 fiscal year work plan

International Nuclear Information System (INIS)

1993-01-01

Site Management System (SMS) guidance requires a Fiscal Year Work Plan (FYWP) to be prepared for the Environmental Restoration (ER) Mission Area and all related programs. This revision is a complete update to cover the FY 1994 time period. This document describes the overall ER Missions Area and provides FYWP appendices for each of the following five program areas: Remedial Action (RA); Decontamination and Decommissioning (D ampersand D); Project Management and Support (PM ampersand S); Surveillance and Maintenance (S ampersand M); and Disposal Facilities (DF)

Clean Water Act (Section 404) and Rivers and Harbors Act (Sections 9 and 10). Environmental Guidance Program Reference Book, Revision 4

Energy Technology Data Exchange (ETDEWEB)

None

1992-03-01

This Reference Book contains a current copy of the Clean Water Act (Section 404) and the Rivers and Harbors Act (Sections 9 and 10) and those regulations that implement those sections of the statutes and appear to be most relevant to DOE activities. The document is provided to DOE and contractor staff for informational purposes only and should not be interpreted as legal guidance. Updates that include important new requirements will be provided periodically. Questions concerning this Reference Book may be directed to Mark Petts, IH-231 (FTS 896-2609 or Commercial 202/586-2609).

Guidance for the scientific requirements for health claims related to antioxidants, oxidative damage and cardiovascular health (Revision 1)

DEFF Research Database (Denmark)

Sjödin, Anders Mikael

2018-01-01

of additional health claim applications related to antioxidants, oxidative damage and cardiovascular health, and the information collected from a Grant launched in 2014. This guidance is intended to assist applicants in preparing applications for the authorisation of health claims related to the antioxidants......EFSA asked the Panel on Dietetic Products, Nutrition and Allergies (NDA) to update the guidance on the scientific requirements for health claims related to antioxidants, oxidative damage and cardiovascular health published in 2011. The update takes into accounts experiences gained with evaluation......, oxidative damage and cardiovascular health. The document was subject to public consultation (from 12 July to 3 September 2017). This document supersedes the guidance on the scientific requirements for health claims related to antioxidants, oxidative damage and cardiovascular health published in 2011...

Documentation Panels Enhance Teacher Education Programs

Science.gov (United States)

Warash, Bobbie Gibson

2005-01-01

Documentation of children's projects is advantageous to their learning process and is also a good method for student teachers to observe the process of learning. Documentation panels are a unique way to help student teachers understand how children learn. Completing a panel requires a student teacher to think through a process. Teachers must learn…

GUIDANCE COUNSELOR INSTITUTE FOR HEALTH CAREERS (JULY 7-22, 1966).

Science.gov (United States)

MORGAN, PHILIP W.

THE INSTITUTE, SPONSORED BY A FEDERATED CHARITY REPRESENTING 78 NONPROFIT VOLUNTARY HOSPITALS IN NEW YORK CITY, WAS ATTENDED BY 48 HIGH SCHOOL AND EMPLOYMENT SERVICE COUNSELORS. THE NEED FOR SUCH INSTITUTES WAS DOCUMENTED BY A PRE-INSTITUTE QUESTIONNAIRE TO LICENSED GUIDANCE COUNSELORS. TO EVALUATE THE INSTITUTE, THE PROFESSIONAL EXAMINATION…

NASA software documentation standard software engineering program

Science.gov (United States)

1991-01-01

The NASA Software Documentation Standard (hereinafter referred to as Standard) can be applied to the documentation of all NASA software. This Standard is limited to documentation format and content requirements. It does not mandate specific management, engineering, or assurance standards or techniques. This Standard defines the format and content of documentation for software acquisition, development, and sustaining engineering. Format requirements address where information shall be recorded and content requirements address what information shall be recorded. This Standard provides a framework to allow consistency of documentation across NASA and visibility into the completeness of project documentation. This basic framework consists of four major sections (or volumes). The Management Plan contains all planning and business aspects of a software project, including engineering and assurance planning. The Product Specification contains all technical engineering information, including software requirements and design. The Assurance and Test Procedures contains all technical assurance information, including Test, Quality Assurance (QA), and Verification and Validation (V&V). The Management, Engineering, and Assurance Reports is the library and/or listing of all project reports.

Glossary of CERCLA, RCRA and TSCA related terms and acronyms. Environmental Guidance

Energy Technology Data Exchange (ETDEWEB)

1993-10-01

This glossary contains CERCLA, RCRA and TSCA related terms that are most often encountered in the US Department of Energy (DOE) Environmental Restoration and Emergency Preparedness activities. Detailed definitions are included for key terms. The CERCLA definitions included in this glossary are taken from the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), as amended and related federal rulemakings. The RCRA definitions included in this glossary are taken from the Resource Conservation and Recovery Act (RCRA) and related federal rulemakings. The TSCA definitions included in this glossary are taken from the Toxic Substances and Control Act (TSCA) and related federal rulemakings. Definitions related to TSCA are limited to those sections in the statute and regulations concerning PCBs and asbestos.Other sources for definitions include additional federal rulemakings, assorted guidance documents prepared by the US Environmental Protection Agency (EPA), guidance and informational documents prepared by the US Department of Energy (DOE), and DOE Orders. The source of each term is noted beside the term. Terms presented in this document reflect revised and new definitions published before July 1, 1993.

Guidance for the Implementation and Follow-up of Identified Energy and Water Efficiency Measures in Covered Facilities

Energy Technology Data Exchange (ETDEWEB)

None

2012-09-01

This document provides specific guidance to agencies on the implementation and follow-up of energy and water efficiency measures identified and undertaken per Section 432 of the Energy Independence and Security Act of 2007 (EISA) (42 U.S.C. 8253(f)(4) and (5)) This guidance also provides context for how these activities fit into the comprehensive approach to facility energy and water management outlined by the statute and incorporates by reference previous DOE guidance released for Section 432 of EISA and other related documents. 42 U.S.C. 8253(f)(7)(A) specifies that facility energy managers shall certify compliance for each covered facility with the 42 U.S.C. 8253(f)(2)-(5) requirements via a web-based tracking system and make it publicly available. This document also describes the role of the tracking system that has been developed for the collection and reporting of data needed for the demonstration of compliance and progress toward meeting all energy and water efficiency requirements outlined in the statute.

Documenting Employee Conduct

Science.gov (United States)

Dalton, Jason

2009-01-01

One of the best ways for a child care program to lose an employment-related lawsuit is failure to document the performance of its employees. Documentation of an employee's performance can provide evidence of an employment-related decision such as discipline, promotion, or discharge. When properly implemented, documentation of employee performance…

Guidance system operations plan for manned LM earth orbital and lunar missions using program luminary 1E. Section 2: Data links

Science.gov (United States)

Hamilton, M. H.

1972-01-01

Data links for the guidance system of manned lunar module orbital and lunar missions are presented. Subjects discussed are: (1) digital uplink to lunar module, (2) lunar module liftoff time increment, (3) lunar module contiguous block update, (4) lunar module scatter update, (5) lunar module digital downlink, and (6) absolute addresses for update program.

Patterns for Effectively Documenting Frameworks

Science.gov (United States)

Aguiar, Ademar; David, Gabriel

Good design and implementation are necessary but not sufficient pre-requisites for successfully reusing object-oriented frameworks. Although not always recognized, good documentation is crucial for effective framework reuse, and often hard, costly, and tiresome, coming with many issues, especially when we are not aware of the key problems and respective ways of addressing them. Based on existing literature, case studies and lessons learned, the authors have been mining proven solutions to recurrent problems of documenting object-oriented frameworks, and writing them in pattern form, as patterns are a very effective way of communicating expertise and best practices. This paper presents a small set of patterns addressing problems related to the framework documentation itself, here seen as an autonomous and tangible product independent of the process used to create it. The patterns aim at helping non-experts on cost-effectively documenting object-oriented frameworks. In concrete, these patterns provide guidance on choosing the kinds of documents to produce, how to relate them, and which contents to include. Although the focus is more on the documents themselves, rather than on the process and tools to produce them, some guidelines are also presented in the paper to help on applying the patterns to a specific framework.

Program information architecture/document hierarchy. [Information Management Systems, it's components and rationale

Energy Technology Data Exchange (ETDEWEB)

Woods, T.W.

1991-09-01

The Nuclear Waste Management System (NWMS) Management Systems Improvement Strategy (MSIS) (DOE 1990) requires that the information within the computer program and information management system be ordered into a precedence hierarchy for consistency. Therefore, the US Department of Energy (DOE). Office of Civilian Radioactive Waste Management (OCRWM) requested Westinghouse Hanford Company to develop a plan for NWMS program information which the MSIS calls a document hierarchy. This report provides the results of that effort and describes the management system as a program information architecture.'' 3 refs., 3 figs.

Program management strategies for following EPA guidance for remedial design/remedial action at DOE sites

International Nuclear Information System (INIS)

Hopper, J.P.; Chew, J.R.; Kowalski, T.E.

1991-01-01

At the US Department of Energy (DOE) facilities, environmental restoration is being conducted in accordance with Federal Facilities Compliance Agreements (or Interagency Agreements). These agreements establish a cooperative working relationship and often define roles, responsibilities and authorities for conduct and oversight of the Remedial Action Programs. The US Environmental Protection Agency (EPA) has guidelines on how to initiate and perform remedial actions for sites they are remediating under the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) as amended by the Superfund Amendments and Re-Authorization Act (SARA). This paper addresses some of the difference and commonalities between the DOE project management procedures and EPA guidance documents. This report covers only the RD/RA phase of environmental restoration. On the surface, there are many apparent differences between the DOE and EPA project management processes. Upon closer review, however, many of the differences are the result of applying different terminology to the same phase of a project. By looking for the similarities in the two processes rather than hunting for differences, many communication problems are avoided. Understanding both processes also aids in figuring out when, how and to what extent EPA should participate in the RD/RA phase for DOE lead cleanup activities. The DOE Remedial Design and Remedial Action process is discussed in a stepwise manner and compared to the EPA process. Each element of the process is defined. Activities common to both the EPA and DOE are correlated. The annual DOE budget cycle for remediation projects and the four-year cycle for appropriation of remediation funds are discussed, and the constraints of this process examined. DOE orders as well as other requirements for RD/RA activities are summarized and correlated to EPA regulations where this is possible

Program Management Plan for the Martin Marietta Energy Systems, Inc., Oak Ridge National Laboratory Site Environmental Restoration Program

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

This program management plan describes the scope, objectives, and method of accomplishment for the Martin Marietta Energy Systems, Inc. (Energy Systems) Oak Ridge National laboratory (ORNL) Environmental Restoration (ER) Program. The ORNL ER Program is one of five site program, receiving guidance from and reporting to the Energy Systems ER Division. Therefore, all ORNL ER policies and procedures are consistent with ER Division policies and procedures. This plan covers all ORNL ER activities, the participants involved in these activities (and their roles and responsibilities), and all phases of the remediation process. This plan will also serve as a template that may be supplemented as necessary to produce individual project management plans for specific projects. This document explains how the Energy Systems ORNL ER Program does business, so the ORNL ER Program`s management structure is illustrated in detail. Personnel are matrixed to the ER Program from other organizations to assist with specific projects. This plan identifies positions at the program level and discusses responsibilities and interactions with positions at the project level. This plan includes sections that describe requirements for project plans, work breakdown structures, schedules, project management and cost control systems, and information and reporting. Project management plans will utilize the work breakdown structure and dictionary pages in the appropriate life cycle baseline report This plan describes the information that should be contained in ORNL ER project management plans. The most important milestones are primary documents relating to the management and remediation of contaminated sites. Primary document milestones are subject to stipulated penalties and receive paramount attention.

Guidance for implementing an environmental, safety and health assurance program. Volume 2. A model plan for environmental, safety and health staff audits and appraisals

International Nuclear Information System (INIS)

Ellingson, A.C.

1980-09-01

This is 1 of 15 documents designed to illustrate how an Environmental, Safety and Health (ES and H) Assurance Program may be implemented. The generic definition of ES and H Assurance Programs is given in a companion document entitled An Environmental, Safety and Health Assurance Program Standard. This document is concerned with ES and H audit and appraisal activities of an ES and H Staff Organization as they might be performed in an institution whose ES and H program is based upon the ES and H Assurance Program Standard. An annotated model plan for ES and H Staff audits and appraisals is presented and discussed

Groundwater protection management program plan

International Nuclear Information System (INIS)

1992-06-01

US Department of Energy (DOE) Order 5400.1 requires the establishment of a groundwater protection management program to ensure compliance with DOE requirements and applicable Federal, state, and local laws and regulations. The Uranium Mill Tailings Remedial Action (UMTRA) Project Office has prepared a ''Groundwater Protection Management Program Plan'' (groundwater protection plan) of sufficient scope and detail to reflect the program's significance and address the seven activities required in DOE Order 5400.1, Chapter 3, for special program planning. The groundwater protection plan highlights the methods designed to preserve, protect, and monitor groundwater resources at UMTRA Project processing and disposal sites. The plan includes an overview of the remedial action status at the 24 designated processing sites and identifies project technical guidance documents and site-specific documents for the UMTRA groundwater protection management program. In addition, the groundwater protection plan addresses the general information required to develop a water resources protection strategy at the permanent disposal sites. Finally, the plan describes ongoing activities that are in various stages of development at UMTRA sites (long-term care at disposal sites and groundwater restoration at processing sites). This plan will be reviewed annually and updated every 3 years in accordance with DOE Order 5400.1

The Use of Vocational Guidance E-Systems in Colleges of Technology, Saudi Arabia

Science.gov (United States)

Alsaidan, Saad; Zhang, Li

2018-01-01

This study aimed to explore how much interest do technical colleges students have in vocational guidance E-Systems and to detect the most important E-Systems of vocational guidance that they use. The researcher collected data, through questionnaires, from 311 students in their fourth, fifth, or sixth semesters in the colleges of technology in Saudi Arabia. The data were analysed using the chi square test, factor analysis, and descriptive analysis. This study shows the importance in the integration of the E-Systems to vocational guidance. The model includes: the use of e-vocational consulting programs, e-extracurricular programs, e-vocational activities, informational systems, and e-exams for vocational tendency, which were rarely studied before. The results indicated that the college student is highly motivated by vocational guidance using the E-system, unlike the traditional methods of vocational guidance, and young students are motivated by the E-system when it is used in vocational guidance. The study conclude that the integration of the E-system has significantly contributed to vocational guidance. The study recommends that the e-system be implemented to all areas of decision-making. Practitioners should Interact with students through the E-Systems and arrive at decisions that are good for educational growth.

Guidelines for Teaching Undergraduate Sport Sociology. Guidance Document

Science.gov (United States)

Coakley, Jay; Riemer, Brenda; Sailes, Gary; Harrison, Louis; Pittman, Beverly

2009-01-01

Sport sociology is a subdiscipline of sociology that, since the late 1960s, has produced knowledge about sports as social phenomena in a wide range of societies. It may be included as a major specialization area in graduate programs in kinesiology, sports studies and physical education departments, and is widely offered as a single undergraduate…

Technical basis document for internal dosimetry

International Nuclear Information System (INIS)

Hickman, D.P.

1991-01-01

This document provides the technical basis for the Chem-Nuclear Geotech (Geotech) internal dosimetry program. Geotech policy describes the intentions of the company in complying with radiation protection standards and the as low as reasonably achievable (ALARA) program. It uses this policy and applicable protection standards to derive acceptable methods and levels of bioassay to assure compliance. The models and computational methods used are described in detail within this document. FR-om these models, dose- conversion factors and derived limits are computed. These computations are then verified using existing documentation and verification information or by demonstration of the calculations used to obtain the dose-conversion factors and derived limits. Recommendations for methods of optimizing the internal dosimetry program to provide effective monitoring and dose assessment for workers are provided in the last section of this document. This document is intended to be used in establishing an accredited dosimetry program in accordance with expected Department of Energy Laboratory Accreditation Program (DOELAP) requirements for the selected radionuclides provided in this document, including uranium mill tailing mixtures. Additions and modifications to this document and procedures derived FR-om this document are expected in the future according to changes in standards and changes in programmatic mission

Communication Services and Supports for Individuals with Severe Disabilities: Guidance for Assessment and Intervention

Science.gov (United States)

Brady, Nancy C.; Bruce, Susan; Goldman, Amy; Erickson, Karen; Mineo, Beth; Ogletree, Bill T.; Paul, Diane; Romski, Mary Ann; Sevcik, Rose; Siegel, Ellin; Schoonover, Judith; Snell, Marti; Sylvester, Lorraine; Wilkinson, Krista

2015-01-01

The National Joint Committee for the Communication Needs of People with Severe Disabilities (NJC) reviewed literature regarding practices for people with severe disabilities in order to update guidance provided in documents originally published in 1992. Changes in laws, definitions, and policies that affect communication attainments by persons with severe disabilities are presented, along with guidance regarding assessment and intervention practices. A revised version of the Communication Bill of Rights, a powerful document that describes the communication rights of all individuals, including those with severe disabilities is included in this article. The information contained within this article is intended to be used by professionals, family members, and individuals with severe disabilities to inform and advocate for effective communication services and opportunities. PMID:26914467

Individualized guidance and telephone monitoring in a self-supervised home-based physiotherapeutic program in Parkinson

Directory of Open Access Journals (Sweden)

Ihana Thaís Guerra de Oliveira Gondim

Full Text Available Abstract Introduction: Home therapeutic exercises have been a target of interest in the treatment of the Parkinson's disease (PD. The way that the physical therapist guides and monitors these exercises can impact the success of therapy. Objective: To evaluate the effects of individualized orientation and monitoring by telephone in a self-supervised home therapeutic exercise program on signs and symptoms of PD and quality of life (QoL. Methods: Single-blind randomized clinical trials with 28 people with PD (Hoehn and Yahr 1 to 3. Patients were randomized into two groups: experimental and control. The experimental group had a meeting with individualized guidance about physiotherapy exercises present in a manual, received the manual to guide their activities at home and obtained subsequent weekly monitoring by telephone. The control group received the usual cares by the service. Both were orientated to carry out exercises three times a week during 12 weeks. Was evaluated: (1 activities of daily living (ADL and motor examination sections of the Unified Parkinson's Disease Rating Scale (UPDRS and QoL by the Parkinson Disease Questionnaire 39 (PDQ-39. The analysis between groups was performed by the Mann-Whitney test and intragroup through the Wilcoxon (p < 0.05. Results: Significant improvement in ADL (p= 0.001 and motor examination (p= 0.0008 of the UPDRS, PDQ-39 total (p = 0.027 and dimensions mobility (p = 0.027, emotional well-being (p= 0.021 and bodily discomfort (p = 0.027 in the experimental group compared to the control group. Conclusion: The individualized guidance and weekly monitoring by telephone in a self-supervised home therapeutic exercises program promoted positive effects on ADL, motor examination and QoL of people in early stages of PD.

Maintenance program guidelines for programmatic equipment

International Nuclear Information System (INIS)

1994-11-01

The Division Directors at Lawrence Berkeley Laboratory are responsible for implementing a maintenance program for research equipment (also referred to as programmatic equipment) assigned to them. The program must allow maintenance to be accomplished in a manner that promotes operational safety, environmental protection and compliance, and cost effectiveness; that preserves the intended functions of the facilities and equipment; and that supports the programmatic mission of the Laboratory. Programmatic equipment -- such as accelerators, lasers, radiation detection equipment, and glove boxes -- is dedicated specifically to research. Installed equipment, by contrast, includes the mechanical and electrical systems installed as part of basic building construction, equipment essential to the normal functioning of the facility and its intended use. Examples of installed equipment are heating, ventilating, and air conditioning systems; elevators; and communications systems. The LBL Operating and Assurance Program Plan (PUB-3111, Revision 4) requires that a maintenance program be prepared for programmatic equipment and defines the basic maintenance program elements. Such a program of regular, documented maintenance is vital to the safety and quality of research activities. As a part of that support, this document offers guidance to Laboratory organizations for developing their maintenance programs. It clarifies the maintenance requirements of the Operating and Assurance Program (OAP) and presents an approach that, while not the only possibility, can be expected to produce an effective maintenance program for research equipment belonging to the Laboratory's organizations

Software Engineering Program: Software Process Improvement Guidebook

Science.gov (United States)

1996-01-01

The purpose of this document is to provide experience-based guidance in implementing a software process improvement program in any NASA software development or maintenance community. This guidebook details how to define, operate, and implement a working software process improvement program. It describes the concept of the software process improvement program and its basic organizational components. It then describes the structure, organization, and operation of the software process improvement program, illustrating all these concepts with specific NASA examples. The information presented in the document is derived from the experiences of several NASA software organizations, including the SEL, the SEAL, and the SORCE. Their experiences reflect many of the elements of software process improvement within NASA. This guidebook presents lessons learned in a form usable by anyone considering establishing a software process improvement program within his or her own environment. This guidebook attempts to balance general and detailed information. It provides material general enough to be usable by NASA organizations whose characteristics do not directly match those of the sources of the information and models presented herein. It also keeps the ideas sufficiently close to the sources of the practical experiences that have generated the models and information.

75 FR 5356 - Office of New Reactors; Final Interim Staff Guidance on Post-Combined License Commitments

Science.gov (United States)

2010-02-02

... the guidance provided to the NRC staff in Section 1.0, ``Introduction and Interfaces,'' of NUREG-0800, ``Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants,'' concerning the... maintains ADAMS, which provides text and image files of NRC's public documents. These documents may be...

78 FR 79328 - Amendments to Material Control and Accounting Regulations and Proposed Guidance for Fuel Cycle...

Science.gov (United States)

2013-12-30

..., 72, 74, and 150 [NRC-2009-0096 and NRC-2013-0195] RIN 3150-AI61 Amendments to Material Control and Accounting Regulations and Proposed Guidance for Fuel Cycle Facility Material Control and Accounting Plans... of this document. NRC's Agencywide Documents Access and Management System (ADAMS): You may access...

USDOT guidance for connected vehicle deployments : institutional and business models and financial sustainability.

Science.gov (United States)

2016-07-01

This document provides guidance material in regards to Institutional and Business issues as well as Financial Sustainability for the CV Pilots Deployment Concept Development Phase. This material also provides part of the foundation for the Performanc...

Program Management Plan for the Martin Marietta Energy Systems, Inc., Oak Ridge National Laboratory Site Environmental Restoration Program

International Nuclear Information System (INIS)

1994-07-01

This program management plan describes the scope, objectives, and method of accomplishment for the Martin Marietta Energy Systems, Inc. (Energy Systems) Oak Ridge National laboratory (ORNL) Environmental Restoration (ER) Program. The ORNL ER Program is one of five site program, receiving guidance from and reporting to the Energy Systems ER Division. Therefore, all ORNL ER policies and procedures are consistent with ER Division policies and procedures. This plan covers all ORNL ER activities, the participants involved in these activities (and their roles and responsibilities), and all phases of the remediation process. This plan will also serve as a template that may be supplemented as necessary to produce individual project management plans for specific projects. This document explains how the Energy Systems ORNL ER Program does business, so the ORNL ER Program's management structure is illustrated in detail. Personnel are matrixed to the ER Program from other organizations to assist with specific projects. This plan identifies positions at the program level and discusses responsibilities and interactions with positions at the project level. This plan includes sections that describe requirements for project plans, work breakdown structures, schedules, project management and cost control systems, and information and reporting. Project management plans will utilize the work breakdown structure and dictionary pages in the appropriate life cycle baseline report This plan describes the information that should be contained in ORNL ER project management plans. The most important milestones are primary documents relating to the management and remediation of contaminated sites. Primary document milestones are subject to stipulated penalties and receive paramount attention

Vocational Guidance and Counselling for Young People and Adults in the European Community. Findings of a Conference (Berlin, West Germany, December 7-8, 1989).

Science.gov (United States)

de Vries, Heinz J., Ed.

1990-01-01

This document reports on a conference centered around three topics: vocational guidance in the Member States of the European Community (EC), the "Europeanization" of vocational guidance, and approaches to cross-frontier vocational guidance. Among the recommendations of the conference participants are the following: the tasks of…

Documentation of Concurrent programs.

Science.gov (United States)

1983-07-01

preparing the documentation formats, and Tom McDonald for preparing the supplemental materials and statistical analyses. 16 [ 1 -16- I j REFERENCES I Boehm...34*h (eeeeeotop to enter h, to IAmlOCSot land ,uoMXM to R&’T- kfC ’Cod At 1*1 ,lgo: 0) 4 O ~ en ttR .I SA’ tgOhegl that ’t to 40n. .hi &ren a ~ O toll s

Guidance document to the BC emission offsets regulation

International Nuclear Information System (INIS)

2010-11-01

British Columbia's (BC) emission offset regulations were established under the Greenhouse Gas Reduction Targets Act passed in 2007. Targets for greenhouse gas (GHG) emission reductions included a 6 percent reduction by 2012; an 18 percent reduction by 2016; a 33 percent reduction by 2020; and an 80 percent reduction by 2050. Carbon neutral agreements began in 2008, and covered emissions produced from government business travel and by provincial government ministries and agencies. This report presented a list of key recommendations developed by the Pacific Carbon Trust for use in future carbon offset projects. Recommendations included the use of correct emission factors when quantifying projected emission reductions from an offset project; the use of a robust data management system; and the use of evidence in supporting additionality arguments. The document outlined planning procedures for project baseline selection processes, protocol selections, and the identification of sources sinks and reservoirs. Issues related to quantification and measurements, emissions factors, and accuracy and uncertainty were also addressed. Validation, verification, and contracting options were also presented. 6 tabs., 3 figs.

Special nuclear material information, security classification guidance. Instruction

International Nuclear Information System (INIS)

Flickinger, A.

1982-01-01

The Instruction reissues DoD Instruction 5210.67, July 5, 1979, and provides security classification guidance for information concerning significant quantities of special nuclear material, other than that contained in nuclear weapons and that used in the production of energy in the reactor plant of nuclear-powered ships. Security classification guidance for these data in the latter two applications is contained in Joint DoE/DoD Nuclear Weapons Classification Guide and Joint DoE/DoD Classification Guide for the Naval Nuclear Propulsion Program

Evaluating Realized Impacts of DOE/EERE R&D Programs. Standard impact evaluation method

Energy Technology Data Exchange (ETDEWEB)

Ruegg, Rosalie [TIA Consulting, Inc. (United States); O' Connor, Alan C. [RTI International, Research Triangle Park, NC (United States); Loomis, Ross J. [RTI International, Research Triangle Park, NC (United States)

2014-08-01

This document provides guidance for evaluators who conduct impact assessments of research and development (R&D) programs for the U.S. Department of Energy’s (DOE) Office of Energy Efficiency and Renewable Energy (EERE). It is also targeted at EERE program staff responsible for initiating and managing commissioned impact studies. The guide specifies how to estimate economic benefits and costs, energy saved and installed or generated, environmental impacts, energy security impacts, and knowledge impacts of R&D investments in advanced energy technologies.

Guidance on meeting DOE order requirements for traceable nondestructive assay measurements

International Nuclear Information System (INIS)

1994-05-01

Purpose of this guide is to facilitate accuracy and precision of nondestructive assay measurements through improvement of the materials and process of traceability. This document provides DOE and its contractor facilities with guidance to establish traceability to the national measurement base for site-prepared NDA working reference materials

Guidance for Federal Agencies on Executive Order 13693 - Federal Fleet Management

Energy Technology Data Exchange (ETDEWEB)

None, None

2017-01-02

Document contains guidance on the federal fleet requirements of Executive Order 13693: Planning for Federal Sustainability in the Next Decade and helps federal agencies subject to the executive order develop an overall approach for reducing total fleet greenhouse gas (GHG) emissions and fleet-wide per-mile GHG emissions.

Interim guidance for the safe transport of reprocessed uranium

International Nuclear Information System (INIS)

1994-06-01

Increasingly reprocessed uranium is being used for the fabrication of nuclear fuel elements. Different intermediate reprocessing steps are carried out at different locations. Therefore, transportation of uranium material is necessary. Due to the difference in isotope composition of reprocessed uranium then unirradiated uranium a doubt is casted on the presumption that packages used for the transport of unirradiated uranium are automatically suitable for reprocessed uranium compounds. The Standing Advisory Group on the Safe Transport of Radioactive Material (SAGSTRAM) recommended that the issue be reviewed by consultants and that a document be developed that would give guidance to users of the Regulations. This TECDOC is the result of the endeavors of the experts convened at two Consultants Services meetings. It contains guidance on the provisions in the current Regulations as well as proposals for changes to the new Revised Edition whose publication is planned for 1996. This document demonstrates that under the present Transport Regulations it is possible in most cases to ship reprocessed uranium compounds in the same packages as unirradiated uranium compounds. In few cases a more stringent package type is required. 8 refs, 22 figs, 19 tabs

UK regulatory standards - the 'Guidance on requirements for authorisation'

International Nuclear Information System (INIS)

Williams, C.R.

1999-01-01

In the United Kingdom, disposal of radioactive waste requires an authorisation under the Radioactive Substances Act 1993. The power to grant such authorisations rests with the Environment Agency for disposals in England and Wales, and with similar Agencies in Scotland and Northern Ireland - namely the Scottish Environment Protection Agency (SEPA) and the Environment and Heritage Service (EHS) of the Department of the Environment for Northern Ireland. In 1997, following two rounds of consultation, the Environment Agency jointly with SEPA and EHS published a document 'Disposal Facilities on Land for Low and Intermediate Level Radioactive Wastes: Guidance on Requirements for Authorisation' - the GRA document. The GRA document outlines the regulatory framework governing the disposal of radioactive waste, general guidance on procedures, the principles and criteria against which proposals for a disposal facility will be assessed, and the radiological and technical requirements which a facility will be expected to meet. In particular, the document states that, in the period after control is withdrawn, the assessed radiological risk from a facility to a representative member of the potentially exposed group at greatest risk should be consistent with a risk target of 10 -6 per year. The document also specifies the information which a developer will need to provide, to demonstrate that a proposal is consistent with the principles and requirements, and identifies other, non-risk-based, criteria. In March 1997, the Secretary of State for the Environment rejected a planning appeal by United Kingdom Nirex Ltd for an underground Rock Characterisation Facility located near Sellafield in Cumbria. That decision has effectively delayed the construction of any deep repository in the UK. Subsequently a House of Lords Select Committee has commenced a major review of nuclear waste management. The Environment Agency continues to be responsible for the authorisation of the shallow

Documentation and verification required for type A packaging use

Energy Technology Data Exchange (ETDEWEB)

O`Brien, J.H.

1997-07-30

This document furnishes knowledge and methods for verifying compliance with the U.S. Department of Transportation (DOT) packaging requirements for shipping Type A quantities of radioactive material. The primary emphasis is on the requirements identified in 49 CFR 173.415(a), which states, ``Each offeror of a Specification 7A package must maintain on file for at least one year after the shipment, and shall provide to DOT on request, complete documentation of tests and an engineering evaluation of comparative data showing that the construction methods, packaging design, and materials of construction comply with that specification.`` This guidance document uses a checklist to show compliance.

Documentation and verification required for type A packaging use

International Nuclear Information System (INIS)

O'Brien, J.H.

1997-01-01

This document furnishes knowledge and methods for verifying compliance with the U.S. Department of Transportation (DOT) packaging requirements for shipping Type A quantities of radioactive material. The primary emphasis is on the requirements identified in 49 CFR 173.415(a), which states, ''Each offeror of a Specification 7A package must maintain on file for at least one year after the shipment, and shall provide to DOT on request, complete documentation of tests and an engineering evaluation of comparative data showing that the construction methods, packaging design, and materials of construction comply with that specification.'' This guidance document uses a checklist to show compliance

Guidance document for the preparation of waste management plans for the Environmental Restoration Program at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Clark, C. Jr.

1993-07-01

A project waste management (WM) plan is required for all Oak Ridge National Laboratory (ORNL) Environmental Restoration (ER) Program remedial investigation, decommission and decontamination (D ampersand D), and remedial action (RA) activities. The project WM plan describes the strategy for handling, packaging, treating, transporting, characterizing, storing, and/or disposing of waste produced as part of ORNL ER Program activities. The project WM plan also contains a strategy for ensuring worker and environmental protection during WM activities

Analysis of the implementation of guidance and counseling supervision at senior high schools

Directory of Open Access Journals (Sweden)

Abdul Basith

2017-04-01

Full Text Available The aim of this research is: (1 to analyze the implementation of guidance and counseling supervision, and (2 to find main factors inhibiting the implementation of guidance and counseling supervisory at the Senior High Schools of Singkawang City. The results show that: (1 the implementation of the guidance and counseling supervision has still many weaknesses on each stage done by the supervisors, such as unidentified guidance and counseling teachers‘ needs, the program planning is not yet organized well, the supervisors do not use particular approaches, and they do not control the supervisions carried out, (2 some factors inhibiting the implementation of guidance and counseling supervision include lack of guidance and counseling supervision forces that so many guidance and counseling teachers are not supervised optimally, lack of knowledge and understanding by the supervisors on the implementation, and also minimal development of supervisory competencies in the guidance and counseling field.

Final Documentation: Incident Management And Probabilities Courses of action Tool (IMPACT).

Energy Technology Data Exchange (ETDEWEB)

Edwards, Donna M.; Ray, Jaideep; Tucker, Mark D.; Whetzel, Jonathan; Cauthen, Katherine Regina

2018-03-01

This report pulls together the documentation produced for the IMPACT tool, a software-based decision support tool that provides situational awareness, incident characterization, and guidance on public health and environmental response strategies for an unfolding bio-terrorism incident.

EMP Attachment 3 DOE-SC PNNL Site Dose Assessment Guidance

Energy Technology Data Exchange (ETDEWEB)

Snyder, Sandra F.

2011-12-21

This Dose Assessment Guidance (DAG) describes methods to use to determine the Maximally-Exposed Individual (MEI) location and to estimate dose impact to that individual under the U.S. Department of Energy Office of Science (DOE-SC) Pacific Northwest National Laboratory (PNNL) Site Environmental Monitoring Plan (EMP). This guidance applies to public dose from radioactive material releases to the air from PNNL Site operations. This document is an attachment to the Pacific Northwest National Laboratory (PNNL) Environmental Monitoring Plan (EMP) and describes dose assessment guidance for radiological air emissions. The impact of radiological air emissions from the U.S. Department of Energy Office of Science (DOE-SC) PNNL Site is indicated by dose estimates to a maximally exposed member of the public, referred to as the maximally exposed individual (MEI). Reporting requirements associated with dose to members of the public from radiological air emissions are in 40 CFR Part 61.94, WAC 246-247-080, and DOE Order 458.1. The DOE Order and state standards for dose from radioactive air emissions are consistent with U.S. Environmental Protection Agency (EPA) dose standards in 40 CFR 61.92 (i.e., 10 mrem/yr to a MEI). Despite the fact that the current Contract Requirements Document (CRD) for the DOE-SC PNNL Site operations does not include the requirement to meet DOE CRD 458.1, paragraph 2.b, public dose limits, the DOE dose limits would be met when EPA limits are met.

MONITORED GEOLOGIC REPOSITORY LIFE CYCLE COST ESTIMATE ASSUMPTIONS DOCUMENT

International Nuclear Information System (INIS)

R.E. Sweeney

2001-01-01

The purpose of this assumptions document is to provide general scope, strategy, technical basis, schedule and cost assumptions for the Monitored Geologic Repository (MGR) life cycle cost (LCC) estimate and schedule update incorporating information from the Viability Assessment (VA) , License Application Design Selection (LADS), 1999 Update to the Total System Life Cycle Cost (TSLCC) estimate and from other related and updated information. This document is intended to generally follow the assumptions outlined in the previous MGR cost estimates and as further prescribed by DOE guidance

Monitored Geologic Repository Life Cycle Cost Estimate Assumptions Document

International Nuclear Information System (INIS)

Sweeney, R.

2000-01-01

The purpose of this assumptions document is to provide general scope, strategy, technical basis, schedule and cost assumptions for the Monitored Geologic Repository (MGR) life cycle cost estimate and schedule update incorporating information from the Viability Assessment (VA), License Application Design Selection (LADS), 1999 Update to the Total System Life Cycle Cost (TSLCC) estimate and from other related and updated information. This document is intended to generally follow the assumptions outlined in the previous MGR cost estimates and as further prescribed by DOE guidance

Public health economics: a systematic review of guidance for the economic evaluation of public health interventions and discussion of key methodological issues.

Science.gov (United States)

Edwards, Rhiannon Tudor; Charles, Joanna Mary; Lloyd-Williams, Huw

2013-10-24

If Public Health is the science and art of how society collectively aims to improve health, and reduce inequalities in health, then Public Health Economics is the science and art of supporting decision making as to how society can use its available resources to best meet these objectives and minimise opportunity cost. A systematic review of published guidance for the economic evaluation of public health interventions within this broad public policy paradigm was conducted. Electronic databases and organisation websites were searched using a 22 year time horizon (1990-2012). References of papers were hand searched for additional papers for inclusion. Government reports or peer-reviewed published papers were included if they; referred to the methods of economic evaluation of public health interventions, identified key challenges of conducting economic evaluations of public health interventions or made recommendations for conducting economic evaluations of public health interventions. Guidance was divided into three categories UK guidance, international guidance and observations or guidance provided by individual commentators in the field of public health economics. An assessment of the theoretical frameworks underpinning the guidance was made and served as a rationale for categorising the papers. We identified 5 international guidance documents, 7 UK guidance documents and 4 documents by individual commentators. The papers reviewed identify the main methodological challenges that face analysts when conducting such evaluations. There is a consensus within the guidance that wider social and environmental costs and benefits should be looked at due to the complex nature of public health. This was reflected in the theoretical underpinning as the majority of guidance was categorised as extra-welfarist. In this novel review we argue that health economics may have come full circle from its roots in broad public policy economics. We may find it useful to think in this broader

Supplemental design requirements document, Project W026

International Nuclear Information System (INIS)

Weidert, J.R.

1993-01-01

This document supplements and extends the Functional Design Criteria, SP-W026-FDC-001, for the Waste Receiving and Processing Facility (WRAP), Module 1. It provides additional detailed requirements, summarizes key Westinghouse Hanford Company design guidance, and establishes baseline technical agreements to be used in definitive design of the WRAP-1 facility. Revision 3 of the Supplemental Design Requirements Document has been assigned an Impact Level of 3ESQ based on the content of the entire revision. The actual changes made from Revision 2 have an Impact Level of 3S and the basis for these changes was previously reviewed and approved per WHC correspondence No. 9355770

Method for plant operation guidance by knowledge engineering technique

International Nuclear Information System (INIS)

Kiguchi, Takashi; Yoshida, Kenichi; Motoda, Hiroshi; Kobayashi, Setsuo

1983-01-01

A method for plant operation guidance has been developed by using the Knowledge Engineering technique. The method is characterized by its capability of handling plant dynamics. The knowledge-base includes plant simulation programs as tools to evaluate dynamic behaviors as well as production rules of ''if..., then...'' type. The inference engine is thus capable of predicting plant dynamics and making decisions in accordance with time progress. The performance of the guidance method was evaluated by simulation tests assuming various abnormal situations of a BWR power plant. It was shown that the method can detect each of the abnormal events along the course of their occurrence, and provide the guidance for corrective actions. The operation guidance method proposed in this paper is general and is applicable not only to nuclear power plants but also to other plants such as chemical production plants and fossile power plants. (author)

Environmental Restoration Remedial Action quality assurance requirements document

International Nuclear Information System (INIS)

1991-01-01

This document defines the quality assurance requirements for the US Department of Energy-Richland Operations Office Environmental Restoration Remedial Action program at the Hanford Site. The Environmental Restoration Remedial Action program implements significant commitments made by the US Department of Energy in the Hanford Federal Facility Agreement and Consent Order entered into with the Washington State Department of Ecology and the US Environmental Protection Agency. This document combines quality assurance requirements from various source documents into one set of requirements for use by the US Department of Energy-Richland Operations Office and other Environmental Restoration Remedial Action program participants. This document will serve as the basis for developing Quality Assurance Program Plans and implementing procedures by the participants. The requirements of this document will be applied to activities affecting quality, using a graded approach based on the importance of the item, service, or activity to the program objectives. The Quality Assurance Program that will be established using this document as the basis, together with other program and technical documents, form an integrated management control system for conducting the Environmental Restoration Remedial Action program activities in a manner that provides safety and protects the environment and public health

Oil program implementation plan FY 1996--2000

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-01

This document reaffirms the US Department of Energy (DOE) Office of Fossil Energy commitment to implement the National Oil Research Program in a way to maximize assurance of energy security, economic growth, environmental protection, jobs, improved economic competitiveness, and improved US balance of trade. There are two sections and an appendix in this document. Section 1 is background information that guided its formulation and a summary of the Oil Program Implementation Plan. This summary includes mission statements, major program drivers, oil issues and trends, budget issues, customers/stakeholders, technology transfer, measures of program effectiveness, and benefits. Section 2 contains more detailed program descriptions for the eight technical areas and the NIPER infrastructure. The eight technical areas are reservoir characterization; extraction research; exploration, drilling, and risk-based decision management; analysis and planning; technology transfer; field demonstration projects; oil downstream operations; and environmental research. Each description contains an overview of the program, descriptions on main areas, a discussion of stakeholders, impacts, planned budget projections, projected schedules with Gantt charts, and measures of effectiveness. The appendix is a summary of comments from industry on an earlier draft of the plan. Although changes were made in response to the comments, many of the suggestions will be used as guidance for the FY 1997--2001 plan.

Hanford Waste Vitrification Plant quality assurance program description: Overview and applications

International Nuclear Information System (INIS)

Caplinger, W.H.

1990-12-01

This document describes the Hanford Waste Vitrification Plant Project Quality Assurance Program. This program is being implemented to ensure the acceptability of high-level radioactive canistered waste forms produced by the Hanford Waste Vitrification Plant for disposal in a licensed federal repository. The Hanford Waste Vitrification Plant Quality Assurance Program is comprised of this Quality Assurance Program Description as well as the associated contractors' quality assurance programs. The objective of this Quality Assurance Program Description is to provide the Hanford Waste Vitrification Plant Project participants with guidance and direction for program implementation while satisfying the US Department of Energy Office of Civilian Radioactive Waste Management needs in repository licensing activities with regard to canistered waste forms. To accomplish this objective, this description will be prepared in three parts: Part 1 - Overview and applications document; Part 2 - Development and qualification of the canistered waste form; Part 3 - Production of canistered waste forms. Part 1 describes the background, strategy, application, and content of the Hanford Waste Vitrification Plant Quality Assurance Program. This Quality Assurance Program Description, when complete, is designed to provide a level of confidence in the integrity of the canistered waste forms. 8 refs

RECON: a computer program for analyzing repository economics. Documentation and user's manual. Revision 1

International Nuclear Information System (INIS)

Clark, L.L.; Schutz, M.E.; Luksic, A.T.

1985-07-01

From 1981 through 1984 the Pacific Northwest Laboratory has been developing a computer model named RECON to calculate repository costs from parametric data input. The objective of the program has been to develop the capability to evaluate the effect on costs of changes in repository design parameters and operating scenario assumptions. This report documents the development of the model through September of 1984. Included in the report are: (1) descriptions of model development and the underlying equations, assumptions and definitions; (2) descriptions of data input using either card images or an interactive data input program; and (3) detailed listings of the program and definitions of program variables. Cost estimates generated using the model have been verified against independent estimates and good agreement has been obtained. 2 refs

Accident Analysis Guidance for Completion of 10 CFR 830-Compliant DSAs

International Nuclear Information System (INIS)

Vincent, A.

2002-01-01

Safety analysis contractors responsible for existing nuclear facilities are required to submit a Documented Safety Analysis to the Department of Energy for approval by April 2003. Recognizing that schedule and resource limitations may be significant, an initiative is underway to make available a set of guidance tools. The guidance is in the form of a peer-reviewed Accident Analysis Guidebook, a series of application guides for ''safe harbor'' computer codes, establishment of a configuration-controlled collection of safety analysis software and a central registry to maintain it, and periodic analytical training on accident analysis methods. Delivery of the majority of these products is scheduled to be in FY 2003

Quality Assurance Program Plan for the Waste Sampling and Characterization Facility

International Nuclear Information System (INIS)

Grabbe, R.R.

1995-01-01

The objective of this Quality Assurance Plan is to provide quality assurance (QA) guidance, implementation of regulatory QA requirements, and quality control (QC) specifications for analytical service. This document follows the Department of Energy (DOE)-issued Hanford Analytical Services Quality Assurance Plan (HASQAP) and additional federal [10 US Code of Federal Regulations (CFR) 830.120] QA requirements that HASQAP does not cover. This document describes how the laboratory implements QA requirements to meet the federal or state requirements, provides what are the default QC specifications, and/or identifies the procedural information that governs how the laboratory operates. In addition, this document meets the objectives of the Quality Assurance Program provided in the WHC-CM-4-2, Section 2.1. This document also covers QA elements that are required in the Guidelines and Specifications for Preparing Quality Assurance Program Plans (QAPPs), (QAMS-004), and Interim Guidelines and Specifications for Preparing Quality Assurance Product Plans (QAMS-005) from the Environmental Protection Agency (EPA). A QA Index is provided in the Appendix A

Probabilistic risk assessment (PRA) reference document. Final report

International Nuclear Information System (INIS)

Murphy, J.A.

1984-09-01

This document describes the current status of probabilistic risk assessment (PRA) as practiced in the nuclear reactor regulatory process. The PRA studies that have been completed or are under way are reviewed. The levels of maturity of the methodologies used in a PRA are discussed. Insights derived from PRAs are listed. The potential uses of PRA results for regulatory purposes are discussed. This document was issued for comment in February 1984 entitled Probabilistic Risk Assessment (PRA): Status Report and Guidance for Regulatory Application. The comments received on the draft have been considered for this final version of the report

Sandia National Laboratories, California Pollution Prevention Program annual report

International Nuclear Information System (INIS)

Harris, Janet S.

2011-01-01

The annual program report provides detailed information about all aspects of the SNL/CA Pollution Prevention Program for a given calendar year. It functions as supporting documentation to the SNL/CA Environmental Management System Program Manual. The program report describes the activities undertaken during the past year, and activities planned in future years to implement the Pollution Prevention Program, one of six programs that supports environmental management at SNL/CA. Pollution Prevention supports the goals and objectives to increase the procurement and use of environmentally friendly products and materials and minimize the generation of waste (nonhazardous, hazardous, radiological, wastewater). Through participation on the Interdisciplinary Team P2 provides guidance for integration of environmentally friendly purchasing and waste minimization requirements into projects during the planning phase. Table 7 presents SNL's corporate objectives and targets that support the elements of the Pollution Prevention program.

Development and implementation of documents control and records management system for KNPP units 5 and 6 modernization program

International Nuclear Information System (INIS)

Manchev, B.L.; Ilieva, M.; Nenkova, B. G. . E-mail of corresponding author: ilieva@riskeng.bg; Ilieva, M.)

2005-01-01

It was proposed to KNPP to develop and implement a Dcuments Control and Records Management System for an efficient and effective Configuration Management (CM) Program. It will provide reasonable assurance that consistency among design requirements, physical configuration and facility documentation is established and maintained during the Modernization Program and throughout the life of KNPP Units 5 and 6. The fully implemented CM Program will consider and track the modifications resulting from the Units 5 and 6 Modernization Program and will be consistent with internationally recognized principles and customized to fit within the KNPP organizational structure and philosophy (ANSI/NIRMA CM 1.0 - 2000, Configuration Management Of Nuclear Facilities). Development and implementation phase of Documents Control and Records Management System and SmartDoc information system, as well as ideas for further development are presented in this report. (author)

Assessment model validity document. NAMMU: A program for calculating groundwater flow and transport through porous media

International Nuclear Information System (INIS)

Cliffe, K.A.; Morris, S.T.; Porter, J.D.

1998-05-01

NAMMU is a computer program for modelling groundwater flow and transport through porous media. This document provides an overview of the use of the program for geosphere modelling in performance assessment calculations and gives a detailed description of the program itself. The aim of the document is to give an indication of the grounds for having confidence in NAMMU as a performance assessment tool. In order to achieve this the following topics are discussed. The basic premises of the assessment approach and the purpose of and nature of the calculations that can be undertaken using NAMMU are outlined. The concepts of the validation of models and the considerations that can lead to increased confidence in models are described. The physical processes that can be modelled using NAMMU and the mathematical models and numerical techniques that are used to represent them are discussed in some detail. Finally, the grounds that would lead one to have confidence that NAMMU is fit for purpose are summarised

School Guidance and Counseling in Kenya: Historical Development, Current Status, and Future Prospects

Science.gov (United States)

Wambu, Grace W.; Fisher, Teresa A.

2015-01-01

Despite the government's emphasis on guidance and counseling program implementation in Kenyan schools and a rapid increase in the number of trained school counselors, lack of standardized training curriculums, ethical standards, counseling models, and role ambiguity persist. This article reviews the historical development of guidance and…