Overview of magnet design options: Deliverable D5.1

CERN Document Server

AUTHOR|(CDS)2069265; Toral, Fernando

2016-01-01

This document describes the design options for 16 T superconducting dipole magnets for the FCC hadron collider explored in the frame of the activities of WP5. All options have been considered under comparable assumptions and managed using the same tools to ensure a correct judgement and comparison of their relevant pros and cons. Three baseline design configurations have been explored: 1) block-coils, 2) cosine-theta and 3) common-coils. A fourth option, the canted cosine-theta, has been initiated by Swiss (PSI, not part of EuroCirCol) and US (LBNL, EuroCirCol partner) laboratories. The studies show that, adopting a reference margin to the load line of 14 % and with reasonable assumptions on the conductor performance, the total amount of conductor needed for the entire collider is between 7.5 and 10 ktons. depending on the option. The cosine-theta uses less conductor and the canted cosine-theta uses the largest amount. The characterisation of the magnet design options is complete and the work to finalize and ...

24 CFR 35.120 - Options.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Options. 35.120 Section 35.120... and Definitions for All Programs. § 35.120 Options. (a) Standard treatments. Where interim controls are required by this part, the designated party has the option to presume that lead-based paint or...

Automotive turbogenerator design options

Energy Technology Data Exchange (ETDEWEB)

Rodgers, C. [ITC, San Diego, CA (United States); McDonald, C. [McDonald Thermal Engineering, La Jolla, CA (United States)

1998-12-31

For the small turbogenerator to find reception in the hybrid electric automotive market its major features must be dominated by the following considerations, low cost, high performance, low emissions, compact size and high reliability. Not meeting the first two criteria has been the nemesis of earlier attempts to introduce the small gas turbine for automotive service. With emphasis on the design for low cost and high performance, this paper presents several turbogenerator design flowpath configuration options for the major engine components. The projected evolution from today`s state-of-the-art all metallic engines, to advanced technology ceramic units for service in the early decade of the 21st century, is the major topic of this paper. (author)

Federal Employees Health Benefits Program: Enrollment Options Following the Termination of a Plan or Plan Option. Final rule.

Science.gov (United States)

2015-10-28

The U.S. Office of Personnel Management (OPM) is issuing a final rule to amend the Federal Employees Health Benefits (FEHB) Program regulations regarding enrollment options following the termination of a plan or plan option.

41 CFR 102-194.5 - What is the Standard and Optional Forms Management Program?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What is the Standard and Optional Forms Management Program? 102-194.5 Section 102-194.5 Public Contracts and Property Management... PROGRAMS 194-STANDARD AND OPTIONAL FORMS MANAGEMENT PROGRAM § 102-194.5 What is the Standard and Optional...

Multi-technology option strategy for long term R and D programs on plutonium technologies. Minimizing proliferation risks and preparing for the future

International Nuclear Information System (INIS)

Suzuki, Tatsujiro

1997-01-01

Plutonium programs worldwide are now facing major economic, political and technical challenges. New strategies need to address two distinctive global concerns: minimizing proliferation risks associated with plutonium use, and keeping the options alive to prepare for uncertain energy future. In order to meet those challenges, this paper proposes the introduction of 'multi-technology option strategy'. Such strategy is designed to keep so-called 'technological readiness' state of plutonium technologies worldwide without committing to a fixed technology option and exploring more innovative various technology options. This paper also suggests that such R and D programs can be coordinated and shared among nations that are interested in future plutonium use, and such cooperation can improve transparency of sensitive R and D programs. (author)

Space station data system analysis/architecture study. Task 2: Options development, DR-5. Volume 2: Design options

Science.gov (United States)

1985-01-01

The primary objective of Task 2 is the development of an information base that will support the conduct of trade studies and provide sufficient data to make key design/programmatic decisions. This includes: (1) the establishment of option categories that are most likely to influence Space Station Data System (SSDS) definition; (2) the identification of preferred options in each category; and (3) the characterization of these options with respect to performance attributes, constraints, cost and risk. This volume contains the options development for the design category. This category comprises alternative structures, configurations and techniques that can be used to develop designs that are responsive to the SSDS requirements. The specific areas discussed are software, including data base management and distributed operating systems; system architecture, including fault tolerance and system growth/automation/autonomy and system interfaces; time management; and system security/privacy. Also discussed are space communications and local area networking.

Identifying lubricant options for compressor bearing designs

Science.gov (United States)

Karnaz, J.; Seeton, C.; Dixon, L.

2017-08-01

Today’s refrigeration and air conditioning market is not only driven by the environmental aspects of the refrigerants, but also by the energy efficiency and reliability of system operation. Numerous types of compressor designs are used in refrigeration and air conditioning applications which means that different bearings are used; and in some cases, multiple bearing types within a single compressor. Since only one lubricant is used, it is important to try to optimize the lubricant to meet the various demands and requirements for operation. This optimization entails investigating different types of lubricant chemistries, viscosities, and various formulation options. What makes evaluating these options more challenging is the refrigerant which changes the properties of the lubricant delivered to the bearing. Once the lubricant and refrigerant interaction are understood, through various test methods, then work can start on collaborating with compressor engineers on identifying the lubricant chemistry and formulation options. These interaction properties are important to the design engineer to make decisions on the adequacy of the lubricant before compressor tests are started. This paper will discuss the process to evaluate lubricants for various types of compressors and bearing design with focus on what’s needed for current refrigerant trends. In addition, the paper will show how the lubricant chemistry choice can be manipulated through understanding of the bearing design and knowledge of interaction with the refrigerant to maximize performance. Emphasis will be placed on evaluation of synthetic lubricants for both natural and synthetic low GWP refrigerants.

DESIGN CONSIDERATIONS UPON PRODUCT END-OF-LIFE OPTIONS

Directory of Open Access Journals (Sweden)

BARSAN Lucian

2016-11-01

Full Text Available The paper presents some considerations about the necessity of evaluating the environmental impact of a product during its entire life. The present situation (economic, social and ecologic imposes solutions to reduce this impact as a result of an analysis performed during all stages of the life cycle. This paper focuses on design solutions with consequences in the last stage, the end-of-life. Reusing products, with, or without remanufacturing and recycling the materials from products that cannot be reused represent some options analysed in this paper. The end-of-life options should be known even from the beginning of the design process and should be included as design objectives or, at least as constrictions. Considering them as human needs would naturally include them in the requirements list.

46 CFR 176.650 - Alternative Hull Examination Program options: Divers or underwater ROV.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Alternative Hull Examination Program options: Divers or...) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 176.650 Alternative Hull Examination Program options: Divers or underwater ROV. To complete the...

Designing cost effective water demand management programs in Australia.

Science.gov (United States)

White, S B; Fane, S A

2002-01-01

This paper describes recent experience with integrated resource planning (IRP) and the application of least cost planning (LCP) for the evaluation of demand management strategies in urban water. Two Australian case studies, Sydney and Northern New South Wales (NSW) are used in illustration. LCP can determine the most cost effective means of providing water services or alternatively the cheapest forms of water conservation. LCP contrasts to a traditional approach of evaluation which looks only at means of increasing supply. Detailed investigation of water usage, known as end-use analysis, is required for LCP. End-use analysis allows both rigorous demand forecasting, and the development and evaluation of conservation strategies. Strategies include education campaigns, increasing water use efficiency and promoting wastewater reuse or rainwater tanks. The optimal mix of conservation strategies and conventional capacity expansion is identified based on levelised unit cost. IRP uses LCP in the iterative process, evaluating and assessing options, investing in selected options, measuring the results, and then re-evaluating options. Key to this process is the design of cost effective demand management programs. IRP however includes a range of parameters beyond least economic cost in the planning process and program designs, including uncertainty, benefit partitioning and implementation considerations.

Specific and Optional Curriculum: An Experience in the Undergraduate Program of Chemical Engineering in Cienfuegos University, Cuba

Science.gov (United States)

Martínez, Yolanda García; Velázquez, Claudia Alvarado; Castillo, Rolando Delgado

2016-01-01

This paper pursues to define the pillars for designing the specific (SC) and optional curricula (OC) of Unit Operations and Processes (UOP) Discipline in the Chemical Engineering Program. To achieve this objective a methodology was developed, which was characterized by the participation of every member in the educational process: professors,…

Activation analysis for ITER design options

International Nuclear Information System (INIS)

Attaya, H.

1995-09-01

This paper presents a summary of the activation analyses that have been performed for the shielding blanket (SS/water) and for the breeding blanket (Li/V) of ITER design options. The activation code RACC-P, which has been modified for pulsed operation, has been used in these calculations. The spatial distributions of the radioactive inventory, decay heat, biological hazard potential, and the contact dose were calculated for the two designs for different operation modes and targeted fluences. A one-dimensional toroidal cylindrical geometrical model has been utilized to determine the neutron fluxes in the two designs. The results are normalized for an inboard and outboard neutron wall loadings of 0.91 and 1.2 MW/m 2 respectively

Assessment of Astrid reactor pit design options

International Nuclear Information System (INIS)

Verpoest, Thomas; Villedieu, Alexandre; Robin, Jean-Charles

2014-01-01

Answering the French Act of the 28. of June 2006 about nuclear materials and waste management, the ASTRID (Advanced Sodium Technological Reactor for Industrial Demonstration) Project has the objectives to demonstrate the industrial feasibility based on identified domains (safety, operability, economy) of Sodium-cooled Fast Reactor and to perform transmutation demonstrations. The pre-conceptual design, started in 2010, considers several reactor pit design options. One of the objectives is to define a reference configuration for the ASTRID project which is able to answer safety and design requirements. The components addressed in this article are: the safety vessel and the Decay Heat Removal system through the main vessel. The core catcher associated to the different configurations studied in this article is an internal core catcher (inside the main vessel). This article deals with the different locations of the DHR through the main vessel and the type of the safety vessel (supported versus suspended vessel). These options are studied in order to establish the advantages and drawbacks of the different configurations in terms of economy, safety, In Service Inspection and Repair (ISIR), operability, robustness, and project risk (authors)

46 CFR 115.650 - Alternative Hull Examination (AHE) Program options: Divers or underwater ROV.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Alternative Hull Examination (AHE) Program options... MORE THAN 49 PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.650 Alternative Hull Examination (AHE) Program options: Divers or underwater ROV. To complete your underwater...

Electron ray tracing programs for gun design and beam transport

International Nuclear Information System (INIS)

Herrmannsfeldt, W.B.

1988-05-01

Computer simulation of electron and ion sources is made by using a class of computer codes known as gun design programs. In this paper, we shall first list most of the necessary and some optional capabilities of such programs. Then we will briefly note specific codes and/or authors of codes with attention to specialized applications if any. There may be many more such programs in use than are treated here; we are only trying to cover a range of examples, not perform a comprehensive survey

Impact of ITER liquid metal design options on safety level and licensing - Sweden

International Nuclear Information System (INIS)

Harfors, C.; Devell, L.; Johansson, Kjell; Lundell, B.; Rolandsson, S.

1993-01-01

The safety level and licensability of five design options for ITER coolant, breeding material and structural material are assessed, with emphasis on some specified accident scenarios. The safety level is assessed in terms of barrier requirements and the feasibility to construct and qualify such a barrier. The licensability in Sweden of each design option is assessed based on the indicated safety level and on a judgement of the technical feasibility to construct and qualify the ITER tokamak itself, based on the selected design option. 20 refs

Smart Contract Templates: essential requirements and design options

OpenAIRE

Clack, Christopher D.; Bakshi, Vikram A.; Braine, Lee

2016-01-01

Smart Contract Templates support legally-enforceable smart contracts, using operational parameters to connect legal agreements to standardised code. In this paper, we explore the design landscape of potential formats for storage and transmission of smart legal agreements. We identify essential requirements and describe a number of key design options, from which we envisage future development of standardised formats for defining and manipulating smart legal agreements. This provides a prelimin...

Accreditation of emerging oral health professions: options for dental therapy education programs.

Science.gov (United States)

Gelmon, Sherril B; Tresidder, Anna Foucek

2011-01-01

The study explored the options for accreditation of educational programs to prepare a new oral health provider, the dental therapist. A literature review and interviews of 10 content experts were conducted. The content experts represented a wide array of interests, including individuals associated with the various dental stakeholder organizations in education, accreditation, practice, and licensure, as well as representatives of non-dental accrediting organizations whose experience could inform the study. Development of an educational accreditation program for an emerging profession requires collaboration among key stakeholders representing education, practice, licensure, and other interests. Options for accreditation of dental therapy education programs include establishment of a new independent accrediting agency; seeking recognition as a committee within the Commission on Accreditation of Allied Health Education Programs; or working with the Commission on Dental Accreditation (CODA) to create a new accreditation program within CODA. These options are not mutually exclusive, and more than one accreditation program could potentially exist. An educational accreditation program is built upon a well-defined field, where there is a demonstrated need for the occupation and for accreditation of educational programs that prepare individuals to enter that occupation. The fundamental value of accreditation is as one player in the overall scheme of improving the quality of higher education delivered to students and, ultimately, the delivery of health services. Leaders concerned with the oral health workforce will need to consider future directions and the potential roles of new oral health providers as they determine appropriate directions for educational accreditation for dental therapy.

Planetary Sample Caching System Design Options

Science.gov (United States)

Collins, Curtis; Younse, Paulo; Backes, Paul

2009-01-01

Potential Mars Sample Return missions would aspire to collect small core and regolith samples using a rover with a sample acquisition tool and sample caching system. Samples would need to be stored in individual sealed tubes in a canister that could be transfered to a Mars ascent vehicle and returned to Earth. A sample handling, encapsulation and containerization system (SHEC) has been developed as part of an integrated system for acquiring and storing core samples for application to future potential MSR and other potential sample return missions. Requirements and design options for the SHEC system were studied and a recommended design concept developed. Two families of solutions were explored: 1)transfer of a raw sample from the tool to the SHEC subsystem and 2)transfer of a tube containing the sample to the SHEC subsystem. The recommended design utilizes sample tool bit change out as the mechanism for transferring tubes to and samples in tubes from the tool. The SHEC subsystem design, called the Bit Changeout Caching(BiCC) design, is intended for operations on a MER class rover.

Alberta Environment's weir safety program : options for rehabilitation to improve public safety : a case study of the Calgary weir

Energy Technology Data Exchange (ETDEWEB)

Blakely, D [Alberta Environment, Edmonton, AB (Canada)

2009-07-01

Alberta Environment Water Management Operations (WMO) owns and operates 46 dams and 800 kilometres of canals in Alberta. The WMO consists of 120 staff and several contract operators to take care of this infrastructure. Most of the infrastructure supplies water for irrigation use, which adds 5 billion dollars to the provincial economy annually. Other water uses include stock watering, domestic use, municipal use, recreational use and habitat. Alberta Environment's weir safety program was also discussed along with options for rehabilitation to improve public safety. A case study of Calgary's Weir Dam on the Bow River was highlighted. A brief history of the dam was offered and safety programs around provincially-owned weirs were discussed. Photographs were included to illustrate some of the additional safety measures at the Calgary weir, such as suspended safety buoys upstream of the boom directing paddlers to the portage trail, and signage on the river that can be activated when the boom is out. Typical river users on the Calgary Bow River and safety history at the Calgary Weir were discussed along with other topics such as the Calgary Bow River weir project criteria; project design progress; pre-feasibility options; scale modelling; final design analysis; construction funding; and proposed changes to the safety program for the new weir configuration. figs.

46 CFR 71.50-27 - Alternative Hull Examination (AHE) program options: Divers or underwater remotely operated...

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Alternative Hull Examination (AHE) program options...-27 Alternative Hull Examination (AHE) program options: Divers or underwater remotely operated vehicle... operations; (2) Provide permanent hull markings, a temporary grid system of wires or cables spaced not more...

A Review of Research Methods Used to Examine Employee Assistance Program Delivery Options.

Science.gov (United States)

Csiernik, Rick

1995-01-01

This review of literature on Employee Assistance Programs (EAPs) focuses on EAP delivery options. More than half of the 48 studies reviewed used a case study approach. EAPs provided by on-staff professionals were the most frequently discussed delivery option, although this is not the most dominant form of EAP provision. (SLD)

Electric-powered passenger vehicle design study program. Task 1. Tradeoff studies

Energy Technology Data Exchange (ETDEWEB)

Rowlett, B.H.

1976-09-16

Using the baseline vehicle and power system design established previously to meet the performance goals of the program, three power system computer simulation programs were prepared for the basic vehicle tradeoff studies. These programs simulate the performance of the power system and vehicle over different types of driving conditions such as maximum power acceleration, deceleration, city driving cycles, and hill climbing, and permit accurate determination of the benefits of the unique hybrid power system, the total energy required for the suburban city driving cycle, and the extremes of the operating envelopes of the components so that component design options can be defined and studied. Component design tradeoff studies were conducted, including sensitivity studies to show the criticality of the various losses and unknowns in the analytical models. Also, preliminary vehicle layout studies were performed to determine the best locations of the power system and the batteries. Three basic design options are identified for further study. Economic studies were initiated using analytical models to establish the complete vehicle weight and cost breakdowns. Preliminary reliability and safety studies were completed, and maintainability and safety certification criteria established. The detailed analysis of the power system has verified the feasibility of the system and of the performance expectations. Also, the feasibility of energy recovery from regenerative braking has been confirmed. The sensitivity analysis of the power system shows that sufficient margin for unknown design variables is provided. The preliminary economic analysis indicates that the most difficult objective of the study will be the selection of the cost and weight relationships which are required to achieve the overall cost objectives.

The role of managerial stock option programs in governance: evidence from REIT stock repurchases

NARCIS (Netherlands)

Ghosh, C.; Giambona, E.; Harding, J.P.; Sezer, O.; Sirmans, C.F.

2010-01-01

This article examines the role of stock option programs and executive holdings of stock options in real estate investment trust (REIT) governance. We study the issue by analyzing how the market reaction to a stock repurchase announcement varies as a function of the individual REIT's governance

The $2000 Electric Powertrain Option-1 Program. Final technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-01

This report describes the tasks accomplished as part of Northrop Grumman's TRP $2000 Electric Powertrain Option-1 program. Northrop Grumman has strived to achieve technology advances and development considered as high priority to the success of future electric vehicles. Northrop Grumman has achieved the intent of the program by taking several steps toward reducing the cost of the electric vehicle powertrain, demonstrating technologies in the form of hardware and introducing enhancements into production that are consistent with the needs of the market.

Organizational Design within University Extension Units: Some Concepts, Options, and Guidelines

Science.gov (United States)

Baker, Harold R.

1976-01-01

Drawing on the behavioral sciences, the author outlines alternative modes of structuring and organizing an extension unit. The advantages and disadvantages of several organizational design options, the purposes and management of the temporary task force, and some general guidelines for making organizational design decisions are discussed.…

Controlled Ecological Life Support Systems (CELSS) conceptual design option study

Science.gov (United States)

Oleson, Melvin; Olson, Richard L.

1986-01-01

Results are given of a study to explore options for the development of a Controlled Ecological Life Support System (CELSS) for a future Space Station. In addition, study results will benefit the design of other facilities such as the Life Sciences Research Facility, a ground-based CELSS demonstrator, and will be useful in planning longer range missions such as a lunar base or manned Mars mission. The objectives were to develop weight and cost estimates for one CELSS module selected from a set of preliminary plant growth unit (PGU) design options. Eleven Space Station CELSS module conceptual PGU designs were reviewed, components and subsystems identified and a sensitivity analysis performed. Areas where insufficient data is available were identified and divided into the categories of biological research, engineering research, and technology development. Topics which receive significant attention are lighting systems for the PGU, the use of automation within the CELSS system, and electric power requirements. Other areas examined include plant harvesting and processing, crop mix analysis, air circulation and atmosphere contaminant flow subsystems, thermal control considerations, utility routing including accessibility and maintenance, and nutrient subsystem design.

12-T solenoid-design options for the MFTF-B Upgrade

International Nuclear Information System (INIS)

Schultz, J.H.; Diatchenko, N.

1983-01-01

The major options for the 12 T magnets examined here are the selection of normal, superconducting or hybrid normal/superconducting magnet systems. The tradeoffs are those between the higher initial cost of superconducting magnet system, the need for thick shielding of superconducting magnets, higher recirculating power in the normal magnets and poorly characterized reliability of lightly shielded normal magnets. The size and shielding tradeoffs among these options are illustrated. The design concepts presented here are evaluated only for the first design iteration of MFTF-B + T, mentioned above. In particular, all concepts now being considered have made topological improvements in the center cell, so that neutral beam power is no longer a strong function of choke coil size. This function was strongly favorable to the use of normal magnets over superconducting magnets and its absence will be discussed qualitatively in the cost comparisons

Designing Canada's low-carb diet : options for effective climate policy

Energy Technology Data Exchange (ETDEWEB)

Jaccard, M. [Simon Fraser Univ., Burnaby, BC (Canada)

2007-11-28

This document presented a framework for future Canadian action in designing effective climate policies. The document provided background information on the rationale for reducing greenhouse gas emissions and discussed how much and how quickly. It also discussed Canada-specific targets. The author cautioned that the threat of anthropogenic climate change is worth insuring against and presented a number of criteria for evaluating potential premiums Canadians might pay for an insurance policy. Other options such as subsidies and offsets were also discussed, as well as emission taxation. The document also included a novel suggestion for a carbon-management standard that would apply to all producers and importers of fossil fuels for domestic use. It was concluded that energy efficiency is more expensive to achieve than advocates suggest, but an understanding of this fact is critical if greenhouse gas abatement policies are to be well designed. In addition, subsidies and information programs are largely ineffective by themselves. The author suggested that a carbon tax would be the most economically efficient and administratively simple way to price the atmosphere. 34 refs., 2 figs.

Manchester Coding Option for SpaceWire: Providing Choices for System Level Design

Science.gov (United States)

Rakow, Glenn; Kisin, Alex

2014-01-01

This paper proposes an optional coding scheme for SpaceWire in lieu of the current Data Strobe scheme for three reasons. First reason is to provide a straightforward method for electrical isolation of the interface; secondly to provide ability to reduce the mass and bend radius of the SpaceWire cable; and thirdly to provide a means for a common physical layer over which multiple spacecraft onboard data link protocols could operate for a wide range of data rates. The intent is to accomplish these goals without significant change to existing SpaceWire design investments. The ability to optionally use Manchester coding in place of the current Data Strobe coding provides the ability to DC balanced the signal transitions unlike the SpaceWire Data Strobe coding; and therefore the ability to isolate the electrical interface without concern. Additionally, because the Manchester code has the clock and data encoded on the same signal, the number of wires of the existing SpaceWire cable could be optionally reduced by 50. This reduction could be an important consideration for many users of SpaceWire as indicated by the already existing effort underway by the SpaceWire working group to reduce the cable mass and bend radius by elimination of shields. However, reducing the signal count by half would provide even greater gains. It is proposed to restrict the data rate for the optional Manchester coding to a fixed data rate of 10 Megabits per second (Mbps) in order to make the necessary changes simple and still able to run in current radiation tolerant Field Programmable Gate Arrays (FPGAs). Even with this constraint, 10 Mbps will meet many applications where SpaceWire is used. These include command and control applications and many instruments applications with have moderate data rate. For most NASA flight implementations, SpaceWire designs are in rad-tolerant FPGAs, and the desire to preserve the heritage design investment is important for cost and risk considerations. The

EGUN: An electron optics and gun design program

International Nuclear Information System (INIS)

Herrmannsfeldt, W.B.

1988-10-01

The name EGUN has become commonly associated with the program also known as the SLAC Electron Trajectory Program. This document is an updated version of SLAC-226, published in 1979. The program itself has had substantial upgrading since then, but only a few new features are of much concern to the user. Most of the improvements are internal and are intended to improve speed or accuracy. EGUN is designed to compute trajectories of charged particles in electrostatic and magnetostatic fields, including the effects of space charge and self-magnetic fields. Starting options include Child's Law conditions on cathodes of various shapes, as well as used specified initial conditions. Either rectangular or cylindrical symmetry may be used. In the new jargon, the program is a 2-1/2 dimension code meaning 2-D in all fields and 3-D in all particle motion. A Poisson's Equation Solver is used to find the electrostatic fields by using difference equations derived from the boundary conditions. Magnetic fields are to be specified externally, by the user, by using one of several methods including data from another program or arbitrary configurations of coils. This edition of the documentation also covers the program EGN87c, which is a recently developed version of EGUN designed to be used on the newer models of personal computers, small main frames, work stations, etc. The EGN87c program uses the programming language C which is very transportable so the program should operate on any system that supports C. Plotting routines for most common PC monitors are included, and the capability to make hard copy plots on dot-matrix printer-plotters is provided. 18 refs., 7 figs

Requirements of Integrated Design Teams While Evaluating Advanced Energy Retrofit Design Options in Immersive Virtual Environments

Directory of Open Access Journals (Sweden)

Xue Yang

2015-12-01

Full Text Available One of the significant ways to save energy use in buildings is to implement advanced energy retrofits in existing buildings. Improving energy performance of buildings through advanced energy retrofitting requires a clear understanding of the cost and energy implications of design alternatives from various engineering disciplines when different retrofit options are considered. The communication of retrofit design alternatives and their energy implications is essential in the decision-making process, as it affects the final retrofit selections and hence the energy efficiency of the retrofitted buildings. The objective of the research presented here was to identify a generic list of information requirements that are needed to be shared and collectively analyzed by integrated design teams during advanced energy retrofit design review meetings held in immersive settings. While identifying such requirements, the authors used an immersive environment based iterative requirements elicitation approach. The technology was used as a means to better identify the information requirements of integrated design teams to be analyzed as a group. This paper provides findings on information requirements of integrated design teams when evaluating retrofit options in immersive virtual environments. The information requirements were identified through interactions with sixteen experts in design and energy modeling domain, and validated with another group of participants consisting of six design experts who were experienced in integrated design processes. Industry practitioners can use the findings in deciding on what information to share with integrated design team members during design review meetings that utilize immersive virtual environments.

Estimating the option value of a non-firm electricity tariff

International Nuclear Information System (INIS)

Moore, J.; Horii, B.; Price, S.; Olson, A.; Woo, C.K.

2010-01-01

We estimate the option value of a non-firm electricity tariff commonly used by a local distribution company (LDC) in its electricity demand response program. This option value captures the benefit that a LDC enjoys from not serving an end-use load during high-price hours in a wholesale electricity market. It is conservative in that it does not include the cost savings in meeting the LDC's resource adequacy requirement or deferring transmission and distribution (T and D) investments necessary for delivering reliable service. Illustrated by a Northern California example, our two-pronged approach entails (a) a set of summer monthly market price regressions to forecast daily spot price distributions that incorporate uncertainty in natural gas price and weather; and (b) a simulation exercise to quantify the tariff's value under a specific design. The results indicate that a non-firm service tariff can have varying option value estimates that are highly sensitive to the tariff's design, and that an incentive payment based on the option value alone is likely insufficient to attract customer participation in a non-firm service program. (author)

Cavity design programs

International Nuclear Information System (INIS)

Nelson, E.M.

1996-01-01

Numerous computer programs are available to help accelerator physicists and engineers model and design accelerator cavities and other microwave components. This article discusses the problems these programs solve and the principles upon which these programs are based. Some examples of how these programs are used in the design of accelerator cavities are also given

Management options for implementing a basic and applied research program responsive to CS technology base needs. Task VIII. Review existing CS materials R and D programs

Energy Technology Data Exchange (ETDEWEB)

1980-02-28

Possibilities for setting up a basic and applied research program that would be responsive to the Conservation and Solar energy base needs are considered with emphasis on the area of materials research. Several organizational arrangements for the implementation of this basic and applied research program are described and analyzed. The key functions of the system such as resources allocation, and program coordination and management follow from two fundamental characteristics: assignment of lead responsibility (CS and the Office of Energy Research, ER); and nature of the organizational chain-of-command. Three options are categorized in terms of these two characteristics and discussed in detail. The first option retains lead responsibility in ER, with CS personnel exercising sign-off authority and filling the coordination role. Option 2 places lead responsibility with CS program office management, and utilizes the existing chain-of-command, but adds a Basic and Applied Research Division to each program office. Option 3 also places lead responsibility with CS, but within a new Office of Basic and Applied Research, which would include a Research Coordinator to manage interactions with ER, and Research Managers for each CS program area. (MCW)

Alberta Environment's weir safety program : options for rehabilitation to improve public safety : a case study of the Calgary weir

Energy Technology Data Exchange (ETDEWEB)

Blakely, D. [Alberta Environment, Edmonton, AB (Canada)

2009-07-01

Alberta Environment Water Management Operations (WMO) owns and operates 46 dams and 800 kilometres of canals in Alberta. The WMO consists of 120 staff and several contract operators to take care of this infrastructure. Most of the infrastructure supplies water for irrigation use, which adds 5 billion dollars to the provincial economy annually. Other water uses include stock watering, domestic use, municipal use, recreational use and habitat. Alberta Environment's weir safety program was also discussed along with options for rehabilitation to improve public safety. A case study of Calgary's Weir Dam on the Bow River was highlighted. A brief history of the dam was offered and safety programs around provincially-owned weirs were discussed. Photographs were included to illustrate some of the additional safety measures at the Calgary weir, such as suspended safety buoys upstream of the boom directing paddlers to the portage trail, and signage on the river that can be activated when the boom is out. Typical river users on the Calgary Bow River and safety history at the Calgary Weir were discussed along with other topics such as the Calgary Bow River weir project criteria; project design progress; pre-feasibility options; scale modelling; final design analysis; construction funding; and proposed changes to the safety program for the new weir configuration. figs.

Integrated economic assessment of energy and forestry mitigation options using MARKAL

International Nuclear Information System (INIS)

1998-01-01

There have been a number of economic assessment of GHG mitigation studies carried out in Indonesia. Several alternative mitigation options for energy and non-energy sectors have been described and the economic assessment of the options has been done for each sectors. However, most of the economic assessment particularly for non-energy sector, was not to find a least cost option but the lowest cost options. A program called MARKAL developed by a consortium of energy specialists from more than a dozen countries in the early 1980s, is a program that can be used for optimization, so that the least cost options could be selected. Indonesia has used this program intensively for energy system analysis. Attempt to use this program for other sector has not been developed as this program was designed for energy sector. Therefore, using MARKAL for other sector, all activities of the other sectors should be treated as energy activities. This study is aimed to use MARKAL for analysing both energy and forestry sector together. This paper described briefly the methodology of using MARKAL for both energy and forestry sectors. As the activities in energy sector have unique characteristics, thus only forest activities are described in more detail. (au)

Student Loan Programs. As Federal Costs of Loan Consolidation Rise, Other Options Should be Examined. Report to Congressional Requesters.

Science.gov (United States)

General Accounting Office, Washington, DC.

In this report GAO recommends that the Secretary of Education assess the advantages of consolidation loans for borrowers and the government in light of program costs and identify options for reducing federal costs. Options could include targeting the program to borrowers at risk of default and extending existing consolidation alternatives to more…

41 CFR 102-194.30 - What role does my agency play in the Standard and Optional Forms Management Program?

Science.gov (United States)

2010-07-01

... What role does my agency play in the Standard and Optional Forms Management Program? Your agency head... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What role does my agency play in the Standard and Optional Forms Management Program? 102-194.30 Section 102-194.30 Public...

Evaluation of design feature No.20 -- Ground support options

International Nuclear Information System (INIS)

Duan, F.

2000-01-01

Ground support options are primarily evaluated for emplacement drifts while ground support systems for non-emplacement openings such as access mains and ventilation drifts are not evaluated against LADS evaluation criteria in this report. Considerations include functional requirements for ground support, the use of a steel-lined system, and the feasibility of using an unlined ground support system principally with grouted rock bolts for permanent ground support. The feature evaluation also emphasizes the postclosure effects of ground support materials on waste isolation and the preclosure aspects such as durability, maintainability, constructibility, safety, engineering acceptability, and cost. This evaluation is to: (A) Review the existing analyses, reports, and studies regarding this design feature, and compile relevant information on performance characteristics. (B) Develop an appropriate evaluation approach for evaluating ground support options against evaluation criteria provided by the LADS team. (C) Evaluate ground support options not only for their preclosure performance in terms of drift stability, material durability, maintenance, constructibility, and cost, but also for their postclosure performance in terms of chemical effects of ground support materials (i.e., concrete, steel) on waste isolation and radionuclide transport. Specifically, the scope for ground support options evaluation include: (1) all steel-lined drifts (no cementitious materials), (2) unlined drifts with minimum cementitious materials (e.g., grout for rockbolts), and (3) concrete-lined drifts, with the focus on the postclosure acceptability evaluation. In addition, unlined drifts with zero cementitious materials (e.g., use of frictional bolts such as split sets, Swellex bolts) are briefly discussed. (D) Identify candidate ground support systems that have the potential to enhance the repository performance based on the feature evaluation. and (E) Provide conclusions and recommendations

Design Options to Reduce Development Cost of First Generation Surface Reactors

International Nuclear Information System (INIS)

Poston, David I.; Marcille, Thomas F.

2006-01-01

Low-power surface reactors have the potential to have the lowest development cost of any space reactor application, primarily because system alpha (mass/kg) is not of utmost importance and mission lifetimes do not have to be a decade or more. Even then, the development cost of a surface reactor can vary substantially depending on the performance requirements (e.g. mass, power, lifetime, reliability) and technical development risk deemed acceptable by the end-user. It is important for potential users to be aware of these relationships before they determine their future architecture (i.e. decide what they need). Generally, the greatest potential costs of a space reactor program are a nuclear-powered ground test and extensive material development campaigns, so it is important to consider options that can minimize the need for or complexity of such tasks. The intended goal of this paper is to inform potential surface reactor users of the potential sensitivities of surface reactor development cost to design requirements, and areas where technical risk can be traded with development cost

Designing Pareto-superior demand-response rate options

International Nuclear Information System (INIS)

Horowitz, I.; Woo, C.K.

2006-01-01

We explore three voluntary service options-real-time pricing, time-of-use pricing, and curtailable/interruptible service-that a local distribution company might offer its customers in order to encourage them to alter their electricity usage in response to changes in the electricity-spot-market price. These options are simple and practical, and make minimal information demands. We show that each of the options is Pareto-superior ex ante, in that it benefits both the participants and the company offering it, while not affecting the non-participants. The options are shown to be Pareto-superior ex post as well, except under certain exceptional circumstances. (author)

CANDU design options with detritiation

International Nuclear Information System (INIS)

Wren, D.J.; Hart, R.S.

1997-01-01

CANDU reactors include a number of auxiliary systems to manage the inventory, purification, clean-up and isotopic purity of the heavy water used in the moderator and heat transport system. These systems are designed and installed to treat the moderator and heat transport water in separate parallel systems. One of the reasons for this parallel approach to heavy water management is the tritium inventory in the heavy water. Different levels of tritium accumulate in the moderator and heat transport system during reactor operation, with the moderator water having a much higher tritium concentration. Strict separation of the high- tritium-concentration moderator water from the low-tritium-concentration heat transport system water is an integral component of the CANDU design and operating strategy to limit potential releases of tritium to the containment building atmosphere. AECL is developing a new cost-effective technology for the detritiation of heavy water based on the Combined Electrolysis and Catalytic Exchange (CECE) process. This detritiation technology has the potential to be integrated into the heavy water management systems of a CANDU reactor. On-line detritiation could be used to limit the concentration of tritium in the moderator and also to detritiate any water collected within the containment building from other sources. The availability of economic detritiation technology would provide a flexibility to redesign some of the auxiliary heavy water management systems. In particular, there is potential to eliminate some of the duplication in the current management systems and also reduce costs by reclassifying some reactor systems that would have lower maximum tritium concentrations. This paper discusses some of the advantages of detritiation and some of the conceptual design options that detritiation would provide. The goal would be to lower the overall reactor cost with detritiation, but it is premature to assess whether this goal can be achieved. (author)

Identification of preferred dipole design options and cost estimates: Deliverable D5.2

CERN Document Server

Tommasini, Davide

2017-01-01

This document contains a description of the preferred 16 Tesla dipole magnet baseline design with its expected performances. The document also includes an analysis of the individual merits and risks of the different, initial design options and gives a justification for the selection of the baseline design. The deliverable includes expected field levels, field errors and a cost estimate, which serve as input for the arc design consolidation.

Regulatory frameworks for Natural Gas DSM in Canada : exploring design options, influences and characteristics of success

International Nuclear Information System (INIS)

Simon, J.

2005-11-01

There are 6 natural gas distribution companies in Canada with formal, ratepayer-funded demand side management (DSM) programs. However, the general characteristics and regulatory environment of these companies varies greatly. With the exception of Enbridge Gas and Union Gas, each company is located in a different province, which means that companies face different energy regulations and energy efficiency policies. An introduction to DSM and its regulation in Canada was presented, as well as an overview of common models in Canada, and the general considerations involved in designing a regulatory framework were discussed. Regulatory design options for natural gas demand-side management regulatory frameworks were evaluated. The major factors that influence the frameworks were analyzed, and the characteristics of a successful DSM program were outlined. The research methodology for this paper consisted of telephone interviews with policy-makers, regulators, non-governmental organizations and regulatory affairs personnel from local distribution companies. Results indicated the importance of a clear policy framework that provides direction for DSM designers. The common elements for a successful regulatory framework were considered to be a systems approach to the definition of DSM; clear regulatory rules; a long-term predictable source and level of DSM funding that reflected the maturity of the DSM market; an alignment of government energy policies and DSM regulatory frameworks; and recognition and capturing of the broad range of DSM benefits

Utility Green Pricing Programs: Design, Implementation, and Consumer Response

Energy Technology Data Exchange (ETDEWEB)

Bird, L.; Swezey, B.; Aabakken, J.

2004-02-01

The term green pricing refers to programs offered by utilities in traditionally regulated electricity markets, which allow customers to support the development of renewable energy sources by paying a small premium on their electric bills. Since the introduction of the concept in the United States, the number of unique utility green pricing programs has expanded from just a few programs in 1993 to more than 90 in 2002. About 10% of U.S. utilities offered a green pricing option to about 26 million consumers by the end of 2002. This report provides: (1) aggregate industry data on consumer response to utility programs, which indicate the collective impact of green pricing on renewable energy development nationally; and (2) market data that can be used by utilities as a benchmark for gauging the relative success of their green pricing programs. Specifically, the paper presents current data and trends in consumer response to green pricing, as measured by renewable energy sales, participants, participation rates, and new renewable energy capacity supported. It presents data on various aspects of program design and implementation, such as product pricing, ownership of supplies, retention rates, marketing costs, the effectiveness of marketing techniques, and methods of enrolling and providing value to customers.

Students' guide to program design

CERN Document Server

Robertson, Lesley Anne

1992-01-01

Students' Guide to Program Design is a textbook on program design. This textbook approaches program design by using structures programming techniques and pseudocode to develop a solution algorithm. Divided into 10 chapters, the book begins with a basic explanation of structured programming techniques, top-down development, and modular design. This discussion is followed by detailed concepts of the syntax of pseudocode; methods of defining the problem; the application of basic control structures in the development of the solution algorithm; desk checking techniques; hierarchy charts; and module

[Design for constructability studies in support of the DOE ALWR (Advanced Light Water Reactor) Program

International Nuclear Information System (INIS)

1990-03-01

This technical report accounts for work performed as part of Duke Power Company's Design for Constructability Program. This program is contractual agreement AC03-86SF16566, part of the US Department of Energy's Technology Program in Support of Advanced Light Water Reactors. This report covers the period from contract inception (September 1986) through completion (March 1990). This report is divided into 4 volumes. Volume 1 includes the executive summary and significant program conclusions. The details supporting these conclusions are in Volume 3, Improving Construction Performance, and Volume 4, Enchancing Constructability Through Design. Volume 2 includes a description of the program, objectives, and approach. A significant conclusion from these discussions was the identification of a ''missing link'' in ALWR programs. With an essentially complete, certified design, the majority of the up-front planning and preparation for implementing the design can be accomplished. Though a monumental undertaking beyond the scope of this project, this up-front planning and preparation must be considered as the next logical step for standardization. Much of the planning can be repeated with future plants and marketed to recoup expenditures. Devoting resources to develop the standard design (evolutionary or passive) to a marketable, standard, and comprehensive plant package is essential to revitalizing the option of nuclear energy. The DOE should seriously consider devoting these resources as a logical extension of its ALWR support

Poloidal field system for the ITER hard design option

International Nuclear Information System (INIS)

Schultz, J.H.; Pillsbury, R.D.

1992-01-01

This paper reports on ITER, the International Thermonuclear Experimental Reactor, a collaborative design by the US, EC, Japan, and the USSR of a tokamak fusion reactor that will demonstrate the physics and test the technology needed for commercial fusion reactors. In 1990, the ITER team completed a Conceptual Design Activity (CDA) in which a candidate design was shown to meet the specified goals of the ITER activity at a conceptual level. The four parties have agreed to an Engineering Design Activity (EDA) that includes the necessary additional design and analysis, along with the R and D needed to construct ITER with confidence. The CDA design includes a toroidal field (TF) magnet system that provides the main containment field and a poloidal field (PF) system used to control plasma current and position. The PF system is also used as transformer primary to induce and sustain current in the plasma. Since the volt-seconds available for full-current plasma burn are less than 10% of the total available volt-seconds from the PF system, an area of concern in the CDA design is that unfavorable plasma conditions could compromise the ability of the physics base case design to achieve long pulse burns. A High Aspect Ratio Design (HARD) was conceived as an alternative design option with a much larger bore in the central solenoid to enhance ITER's capabilities for long-burn operation

Summary of Research on Online and Blended Learning Programs That Offer Differentiated Learning Options. REL 2017-228

Science.gov (United States)

Brodersen, R. Marc; Melluzzo, Daniel

2017-01-01

This report summarizes the methodology, measures, and findings of research on the influence on student achievement outcomes of K-12 online and blended face-to-face and online learning programs that offer differentiated learning options. The report also describes the characteristics of the learning programs. Most of the examined programs used…

Key Design Considerations When Calculating Cost Savings for Population Health Management Programs in an Observational Setting.

Science.gov (United States)

Murphy, Shannon M E; Hough, Douglas E; Sylvia, Martha L; Dunbar, Linda J; Frick, Kevin D

2018-02-08

To illustrate the impact of key quasi-experimental design elements on cost savings measurement for population health management (PHM) programs. Population health management program records and Medicaid claims and enrollment data from December 2011 through March 2016. The study uses a difference-in-difference design to compare changes in cost and utilization outcomes between program participants and propensity score-matched nonparticipants. Comparisons of measured savings are made based on (1) stable versus dynamic population enrollment and (2) all eligible versus enrolled-only participant definitions. Options for the operationalization of time are also discussed. Individual-level Medicaid administrative and claims data and PHM program records are used to match study groups on baseline risk factors and assess changes in costs and utilization. Savings estimates are statistically similar but smaller in magnitude when eliminating variability based on duration of population enrollment and when evaluating program impact on the entire target population. Measurement in calendar time, when possible, simplifies interpretability. Program evaluation design elements, including population stability and participant definitions, can influence the estimated magnitude of program savings for the payer and should be considered carefully. Time specifications can also affect interpretability and usefulness. © Health Research and Educational Trust.

The Direct Assignment Option as a Modular Design Component: An Example for the Setting of Two Predefined Subgroups

Directory of Open Access Journals (Sweden)

Ming-Wen An

2015-01-01

Full Text Available Background. A phase II design with an option for direct assignment (stop randomization and assign all patients to experimental treatment based on interim analysis, IA for a predefined subgroup was previously proposed. Here, we illustrate the modularity of the direct assignment option by applying it to the setting of two predefined subgroups and testing for separate subgroup main effects. Methods. We power the 2-subgroup direct assignment option design with 1 IA (DAD-1 to test for separate subgroup main effects, with assessment of power to detect an interaction in a post-hoc test. Simulations assessed the statistical properties of this design compared to the 2-subgroup balanced randomized design with 1 IA, BRD-1. Different response rates for treatment/control in subgroup 1 (0.4/0.2 and in subgroup 2 (0.1/0.2, 0.4/0.2 were considered. Results. The 2-subgroup DAD-1 preserves power and type I error rate compared to the 2-subgroup BRD-1, while exhibiting reasonable power in a post-hoc test for interaction. Conclusion. The direct assignment option is a flexible design component that can be incorporated into broader design frameworks, while maintaining desirable statistical properties, clinical appeal, and logistical simplicity.

An easy and low cost option for economic statistical process control ...

African Journals Online (AJOL)

An easy and low cost option for economic statistical process control using Excel. ... in both economic and economic statistical designs of the X-control chart. ... in this paper and the numerical examples illustrated are executed on this program.

Distributed Energy Implementation Options

Energy Technology Data Exchange (ETDEWEB)

Shah, Chandralata N [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-13

This presentation covers the options for implementing distributed energy projects. It distinguishes between options available for distributed energy that is government owned versus privately owned, with a focus on the privately owned options including Energy Savings Performance Contract Energy Sales Agreements (ESPC ESAs). The presentation covers the new ESPC ESA Toolkit and other Federal Energy Management Program resources.

Safety options for the 1300 MWe program

International Nuclear Information System (INIS)

Cayol, A.; Dupuis, M.C.; Fourest, B.; Oury, J.M.

1980-04-01

Standardization of the nuclear plants built in France implies an examination of the main technical safety options to be taken for a given type of reactor. By this procedure the subjects for which detailed studies will be needed to confirm the decisions made for the project can be defined in advance. In this context the technical safety option analysis for the 1300 MWe plants was conducted from the end of 1975 to the middle of 1978 according to usual regulation examination practice. The main conclusions are presented on the following subjects: safety methods; technical options concerning the containment vessel, primary fluid activity, fuel elements, steam generators; general organization of the lay-out [fr

Designing computer programs

CERN Document Server

Haigh, Jim

1994-01-01

This is a book for students at every level who are learning to program for the first time - and for the considerable number who learned how to program but were never taught to structure their programs. The author presents a simple set of guidelines that show the programmer how to design in a manageable structure from the outset. The method is suitable for most languages, and is based on the widely used 'JSP' method, to which the student may easily progress if it is needed at a later stage.Most language specific texts contain very little if any information on design, whilst books on des

The design of the MAD Design Program

International Nuclear Information System (INIS)

Niederer, J.

1992-01-01

The study of long term stability in particle accelerators has long been served by a group of widely circulated computer programs. The progress in these programs has mirrored the growth and versatility in accelerator size, complexity, and purpose, as well as evolving technologies in computing software and hardware. A number of large accelerator projects during the last decade were designed with the aid of physics programs either written for, or tailored for the project at hand, each invariably benefiting from contributions of previous workers. This paper outlines the recent history of of expample of an accelerator lattice model tool kit, the Methodical Accelerator Design (MAD) Program, which has tried to knit together this collective wisdom of the accelerator community, The ideas behind the software design of the program itself are traced here; the accelerator physics contents and origins are thoroughly documented elsewhere. These informal notes have a Brookhaven flavor, in part because of early BNL efforts to generalize the ways that technical problems are organized and presented to computers. Some recent BNL applications not covered in the extensive CERN documentation are also included

RTP as an Optional Service: It's Alive, But Is It Well?

Energy Technology Data Exchange (ETDEWEB)

Goldman, Charles; Barbose, Galen; Neenan, Bernie

2006-03-10

Economists have advocated for real-time pricing (RTP) of electricity on the basis of the gains in economic efficiency that would result from charging customers the contemporaneous marginal cost of supplying electricity instead of the average cost. In recent years, RTP has also become the subject of interest in a variety of policy contexts, including integrated resource planning initiatives, ongoing efforts to improve efficiency and reliability in competitive electricity markets, and implementation of default service in states with retail choice. Most experience with RTP has been as an optional service, that is, a self-selecting alternative to the standard utility service. By our count, approximately 70 utilities in the U.S. offered an optional RTP program at some point over the past 20 years. However, many programs are now defunct. In 2003, 47 utilities in the U.S. were still offering an optional RTP program, on either a pilot or permanent basis (see Figure 1). In addition, 10 utilities in states with retail choice currently offer RTP as the default service for large customers that are not under contract with a competitive supplier. Another two utilities have received regulatory approval to do so in the next few years. Although the results of a few optional RTP programs have been publicized, the vast majority of programs have operated in relative obscurity. To provide a wider perspective on utility and customer experience with RTP, we surveyed 43 optional RTP programs offered in 2003. We interviewed RTP program managers and other utility staff, and reviewed publicly available sources, including key regulatory documents and program evaluations. Based on this research, we identified trends related to RTP program history and outlook, program design and implementation, customer participation, and participant price response. The results are both surprising and instructive. We conclude that RTP is indeed alive but is not prospering as well it could. Thus, we offer a

24 CFR 982.642 - Homeownership option: Pilot program for homeownership assistance for disabled families.

Science.gov (United States)

2010-04-01

... ASSISTANCE: HOUSING CHOICE VOUCHER PROGRAM Special Housing Types Homeownership Option § 982.642 Homeownership... declared major disaster or emergency. (d) Amount and distribution of homeownership assistance payments. (1... payment on behalf of the family in accordance with § 982.635 and this section. (2) A family that is a low...

Scope Complexity Options Risks Excursions (SCORE) Factor Mathematical Description.

Energy Technology Data Exchange (ETDEWEB)

Gearhart, Jared Lee [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Samberson, Jonell Nicole [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Shettigar, Subhasini [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jungels, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Welch, Kimberly M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Dean A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-03-01

The purpose of the Scope, Complexity, Options, Risks, Excursions (SCORE) model is to estimate the relative complexity of design variants of future warhead options, resulting in scores. SCORE factors extend this capability by providing estimates of complexity relative to a base system (i.e., all design options are normalized to one weapon system). First, a clearly defined set of scope elements for a warhead option is established. The complexity of each scope element is estimated by Subject Matter Experts (SMEs), including a level of uncertainty, relative to a specific reference system. When determining factors, complexity estimates for a scope element can be directly tied to the base system or chained together via comparable scope elements in a string of reference systems that ends with the base system. The SCORE analysis process is a growing multi-organizational Nuclear Security Enterprise (NSE) effort, under the management of the NA-12 led Enterprise Modeling and Analysis Consortium (EMAC). Historically, it has provided the data elicitation, integration, and computation needed to support the out-year Life Extension Program (LEP) cost estimates included in the Stockpile Stewardship Management Plan (SSMP).

General-purpose RFQ design program

International Nuclear Information System (INIS)

Wadlinger, E.A.

1984-01-01

We have written a general-purpose, radio-frequency quadrupole (RFQ) design program that allows maximum flexibility in picking design algorithms. This program optimizes the RFQ on any combination of design parameters while simultaneously satisfying mutually compatible, physically required constraint equations. It can be very useful for deriving various scaling laws for RFQs. This program has a friendly user interface in addition to checking the consistency of the user-defined requirements and is written to minimize the effort needed to incorporate additional constraint equations. We describe the program and present some examples

Fast Spectrum Molten Salt Reactor Options

Energy Technology Data Exchange (ETDEWEB)

Gehin, Jess C [ORNL; Holcomb, David Eugene [ORNL; Flanagan, George F [ORNL; Patton, Bruce W [ORNL; Howard, Rob L [ORNL; Harrison, Thomas J [ORNL

2011-07-01

During 2010, fast-spectrum molten-salt reactors (FS-MSRs) were selected as a transformational reactor concept for light-water reactor (LWR)-derived heavy actinide disposition by the Department of Energy-Nuclear Energy Advanced Reactor Concepts (ARC) program and were the subject of a preliminary scoping investigation. Much of the reactor description information presented in this report derives from the preliminary studies performed for the ARC project. This report, however, has a somewhat broader scope-providing a conceptual overview of the characteristics and design options for FS-MSRs. It does not present in-depth evaluation of any FS-MSR particular characteristic, but instead provides an overview of all of the major reactor system technologies and characteristics, including the technology developments since the end of major molten salt reactor (MSR) development efforts in the 1970s. This report first presents a historical overview of the FS-MSR technology and describes the innovative characteristics of an FS-MSR. Next, it provides an overview of possible reactor configurations. The following design features/options and performance considerations are described including: (1) reactor salt options-both chloride and fluoride salts; (2) the impact of changing the carrier salt and actinide concentration on conversion ratio; (3) the conversion ratio; (4) an overview of the fuel salt chemical processing; (5) potential power cycles and hydrogen production options; and (6) overview of the performance characteristics of FS-MSRs, including general comparative metrics with LWRs. The conceptual-level evaluation includes resource sustainability, proliferation resistance, economics, and safety. The report concludes with a description of the work necessary to begin more detailed evaluation of FS-MSRs as a realistic reactor and fuel cycle option.

Economic assessment of climate adaptation options for urban drainage design in Odense, Denmark.

Science.gov (United States)

Zhou, Q; Halsnæs, K; Arnbjerg-Nielsen, K

2012-01-01

Climate change is likely to influence the water cycle by changing the precipitation patterns, in some cases leading to increased occurrences of precipitation extremes. Urban landscapes are vulnerable to such changes due to the concentrated population and socio-economic values in cities. Feasible adaptation requires better flood risk quantification and assessment of appropriate adaptation actions in term of costs and benefits. This paper presents an economic assessment of three prevailing climate adaptation options for urban drainage design in a Danish case study, Odense. A risk-based evaluation framework is used to give detailed insights of the physical and economic feasibilities of each option. Estimation of marginal benefits of adaptation options are carried out through a step-by-step cost-benefit analysis. The results are aimed at providing important information for decision making on how best to adapt to urban pluvial flooding due to climate impacts in cities.

The safeguards options study

Energy Technology Data Exchange (ETDEWEB)

Hakkila, E.A.; Mullen, M.F.; Olinger, C.T.; Stanbro, W.D. [Los Alamos National Lab., NM (United States); Olsen, A.P.; Roche, C.T.; Rudolph, R.R. [Argonne National Lab., IL (United States); Bieber, A.M.; Lemley, J. [Brookhaven National Lab., Upton, NY (United States); Filby, E. [Idaho National Engineering Lab., Idaho Falls, ID (United States)] [and others

1995-04-01

The Safeguards Options Study was initiated to aid the International Safeguards Division (ISD) of the DOE Office of Arms Control and Nonproliferation in developing its programs in enhanced international safeguards. The goal was to provide a technical basis for the ISD program in this area. The Safeguards Options Study has been a cooperative effort among ten organizations. These are Argonne National Laboratory, Brookhaven National Laboratory, Idaho National Engineering Laboratory, Lawrence Livermore National Laboratory, Los Alamos National Laboratory, Mound Laboratory, Oak Ridge National Laboratory, Pacific Northwest Laboratories, Sandia National Laboratories, and Special Technologies Laboratory. Much of the Motivation for the Safeguards Options Study is the recognition after the Iraq experience that there are deficiencies in the present approach to international safeguards. While under International Atomic Energy Agency (IAEA) safeguards at their declared facilities, Iraq was able to develop a significant weapons program without being noticed. This is because negotiated safeguards only applied at declared sites. Even so, their nuclear weapons program clearly conflicted with Iraq`s obligations under the Nuclear Nonproliferation Treaty (NPT) as a nonnuclear weapon state.

The safeguards options study

International Nuclear Information System (INIS)

Hakkila, E.A.; Mullen, M.F.; Olinger, C.T.; Stanbro, W.D.; Olsen, A.P.; Roche, C.T.; Rudolph, R.R.; Bieber, A.M.; Lemley, J.; Filby, E.

1995-04-01

The Safeguards Options Study was initiated to aid the International Safeguards Division (ISD) of the DOE Office of Arms Control and Nonproliferation in developing its programs in enhanced international safeguards. The goal was to provide a technical basis for the ISD program in this area. The Safeguards Options Study has been a cooperative effort among ten organizations. These are Argonne National Laboratory, Brookhaven National Laboratory, Idaho National Engineering Laboratory, Lawrence Livermore National Laboratory, Los Alamos National Laboratory, Mound Laboratory, Oak Ridge National Laboratory, Pacific Northwest Laboratories, Sandia National Laboratories, and Special Technologies Laboratory. Much of the Motivation for the Safeguards Options Study is the recognition after the Iraq experience that there are deficiencies in the present approach to international safeguards. While under International Atomic Energy Agency (IAEA) safeguards at their declared facilities, Iraq was able to develop a significant weapons program without being noticed. This is because negotiated safeguards only applied at declared sites. Even so, their nuclear weapons program clearly conflicted with Iraq's obligations under the Nuclear Nonproliferation Treaty (NPT) as a nonnuclear weapon state

Mechanical Design Technology--Modified. (Computer Assisted Drafting, Computer Aided Design). Curriculum Grant 84/85.

Science.gov (United States)

Schoolcraft Coll., Livonia, MI.

This document is a curriculum guide for a program in mechanical design technology (computer-assisted drafting and design developed at Schoolcraft College, Livonia, Michigan). The program helps students to acquire the skills of drafters and to interact with electronic equipment, with the option of becoming efficient in the computer-aided…

The experimental Balzac program at Masurca in support of the design of Super Phenix 2

International Nuclear Information System (INIS)

Sztark, H.; d'Angelo, A.; Soule, R.; Granget, G.

1986-09-01

The Balzac experimental program, performed in the Masurca critical assembly at Cadarache since 1985, is designed for the validation of the neutron physics requirements related to the physical options of the SPX2 project. Geometrically simple configurations are chosen in which parameters, typical for those physical options, are varied in a systematic manner while the basic fissile composition is kept the same. Measurements will be made especially of the critical mass, the distributions of reaction rates, spectral indices, 10 B(n,α) reaction and gamma-ray heating in particular in the control-rod and in internal storage regions. Reactivity effects of (UPu)O 2 isotopic composition variations and of different control-rod absorber configurations will be also measured using the MSM technique

Design options for a bunsen reactor.

Energy Technology Data Exchange (ETDEWEB)

Moore, Robert Charles

2013-10-01

This work is being performed for Matt Channon Consulting as part of the Sandia National Laboratories New Mexico Small Business Assistance Program (NMSBA). Matt Channon Consulting has requested Sandia's assistance in the design of a chemical Bunsen reactor for the reaction of SO2, I2 and H2O to produce H2SO4 and HI with a SO2 feed rate to the reactor of 50 kg/hour. Based on this value, an assumed reactor efficiency of 33%, and kinetic data from the literature, a plug flow reactor approximately 1%E2%80%9D diameter and and 12 inches long would be needed to meet the specification of the project. Because the Bunsen reaction is exothermic, heat in the amount of approximately 128,000 kJ/hr would need to be removed using a cooling jacket placed around the tubular reactor. The available literature information on Bunsen reactor design and operation, certain support equipment needed for process operation and a design that meet the specification of Matt Channon Consulting are presented.

75 FR 47710 - TRICARE; Extended Care Health Option

Science.gov (United States)

2010-08-09

... TRICARE; Extended Care Health Option AGENCY: Office of the Secretary, Department of Defense. ACTION: Final... Care Health Option (ECHO) from $2,500 per month to $36,000 per year, and for other non-legislated.... That program, known as the Extended Care Heath Option (ECHO), replaced the Program for Persons with...

Policies and design elements for the repowering of wind farms: A qualitative analysis of different options

International Nuclear Information System (INIS)

Rio, Pablo del; Calvo Silvosa, Anxo; Iglesias Gomez, Guillermo

2011-01-01

Repowering of a wind farm is the process of replacing existing wind turbines with new turbines that either have a larger nameplate capacity or more efficiency, resulting in a net increase of the power generated. Although repowering brings, both, social and private benefits, there are also several obstacles to repowering which justify public support. The aim of this paper is to provide an overview and a qualitative analysis of instruments and design options to support repowering of on-shore wind farms. The multicriteria analysis carried out in this paper shows that all instruments have their advantages and drawbacks. However, feed-in tariffs and investment subsidies seem to be particularly appropriate instruments in this regard. Furthermore, we provide an assessment of different design options to promote repowering according to key assessment criteria. The relevance of design elements hinges on the fact that these are the ones directly affecting the variables that are relevant in the decision to repower (capacity factors and investment costs). - Research highlights: → This paper provides a qualitative analysis of instruments and design options to support repowering in wind farms. → The multicriteria analysis has shown that all instruments have their advantages and drawbacks regarding promotion of repowering. → However, feed-in tariffs and investment subsidies seem to be particularly appropriate instruments in this regard. → The choice of design elements within instruments is at least as important to promote repowering as the choice of specific instruments.

Evaluation of Landfill Cover Design Options for Waste Disposal Sites in the Coastal Regions of Ghana

Directory of Open Access Journals (Sweden)

Kodwo Beedu Keelson

2015-01-01

Full Text Available Uncontrolled leachate generation from operational and closed waste disposal sites is a major environmental concern in the coastal regions of Ghana which have abundant surface water and groundwater resources. The Ghana Landfill Guidelines requires the provision of a final cover or capping system as part of a final closure plan for waste disposal sites in the country as a means of minimizing the harmful environmental effects of these emissions. However, this technical manual does not provide explicit guidance on the material types or configuration for landfill covers that would be suitable for the different climatic conditions in the country. Four landfill cover options which are based on the USEPA RCRA-type and evapotranspirative landfill cover design specifications were evaluated with the aid of the HELP computer program to determine their suitability for waste disposal sites located in the Western, Central and Greater Accra regions. The RCRA Subtitle C cover which yielded flux rates of less than 0.001 mm/yr was found to be suitable for the specific climatic conditions. The RCRA Subtitle D cover was determined to be unsuitable due to the production of very large flux rates in excess of 200 mm/yr. The results for the anisotropic barrier and capillary barrier covers were inconclusive. Recommendations for further study include a longer simulation period as well the study of the combined effects of different topsoil vegetative conditions and evaporative zone depths on the landfill water balance. The use of other water balance models such as EPIC, HYDRUS-2D and UNSAT-H for the evaluation of the evapotranspirative landfill cover design options should also be considered.

Options for rural electrification in Arua District, Uganda

International Nuclear Information System (INIS)

Onzia, Joseph; Núñez Bosch, Osvaldo Manuel

2015-01-01

This study proposed a power generation system suitable for rural area application. The electrification options were proposed for secondary schools, health centres, households and trading centre loads using solar PV system, diesel fired generators, biogas co-fired diesel generators and grid extension. The study is based on simulation, modeling and optimization of renewable energy system. Designs for the options considered were based on the electricity demand and environmental conditions of Arua district. From the designs, capital costs for each option were determined. This was used in carrying out simulations in HOMER computer program to come up with the most cost effective options. Sensitivity analysis was carried out to determine the effects of variation in costs such as diesel price and capital cost of solar PV system.Based on simulation results, it has been found that the trading centre, with 500 kW of electrical demand, must be electrified using the grid extension. The breakeven grid distance is 75.1 km. Grid extension become cost effective compared to diesel generators and solar PV system within this distance. The load at household level ranges from as low as 16 W to 5 kW. For 103 W peak load, the most cost effective option was solar PV system. The second best option was biogas co-fired diesel generator. For schools and health centres with load of up to 15 kW, biogas co-fired generator is the best compared to the total cost of 18 kW diesel fired generator which is higher. Therefore, where biogas cannot be generated, diesel generators should be used. Based on the amount of pollutants produced, a biogas co-fired diesel generator is the best option. (full text)

General purpose nonlinear analysis program FINAS for elevated temperature design of FBR components

International Nuclear Information System (INIS)

Iwata, K.; Atsumo, H.; Kano, T.; Takeda, H.

1982-01-01

This paper presents currently available capabilities of a general purpose finite element nonlinear analysis program FINAS (FBR Inelastic Structural Analysis System) which has been developed at Power Reactor and Nuclear Fuel Development Corporation (PNC) since 1976 to support structural design of fast breeder reactor (FBR) components in Japan. This program is capable of treating inelastic responses of arbitrary complex structures subjected to static and dynamic load histories. Various types of finite element covering rods, beams, pipes, axisymmetric, two and three dimensional solids, plates and shells, are implemented in the program. The thermal elastic-plastic creep analysis is possible for each element type, with primary emphasis on the application to FBR components subjected to sustained or cyclic loads at elevated temperature. The program permits large deformation, buckling, fracture mechanics, and dynamic analyses for some of the element types and provides a number of options for automatic mesh generation and computer graphics. Some examples including elevated temperature effects are shown to demonstrate the accuracy and the efficiency of the program

Scope Complexity Options Risks Excursions (SCORE) Version 3.0 Mathematical Description.

Energy Technology Data Exchange (ETDEWEB)

Gearhart, Jared Lee [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Samberson, Jonell Nicole [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Shettigar, Subhasini [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jungels, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Welch, Kimberly M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Dean A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-03-01

The purpose of the Scope, Complexity, Options, Risks, Excursions (SCORE) model is to estimate the relative complexity of design variants of future warhead options. The results of this model allow those considering these options to understand the complexity tradeoffs between proposed warhead options. The core idea of SCORE is to divide a warhead option into a well- defined set of scope elements and then estimate the complexity of each scope element against a well understood reference system. The uncertainty associated with estimates can also be captured. A weighted summation of the relative complexity of each scope element is used to determine the total complexity of the proposed warhead option or portions of the warhead option (i.e., a National Work Breakdown Structure code). The SCORE analysis process is a growing multi-organizational Nuclear Security Enterprise (NSE) effort, under the management of the NA- 12 led Enterprise Modeling and Analysis Consortium (EMAC), that has provided the data elicitation, integration and computation needed to support the out-year Life Extension Program (LEP) cost estimates included in the Stockpile Stewardship Management Plan (SSMP).

Early Phase Contingency Trajectory Design for the Failure of the First Lunar Orbit Insertion Maneuver: Direct Recovery Options

Science.gov (United States)

Song, Young-Joo; Bae, Jonghee; Kim, Young-Rok; Kim, Bang-Yeop

2017-12-01

To ensure the successful launch of the Korea pathfinder lunar orbiter (KPLO) mission, the Korea Aerospace Research Institute (KARI) is now performing extensive trajectory design and analysis studies. From the trajectory design perspective, it is crucial to prepare contingency trajectory options for the failure of the first lunar brake or the failure of the first lunar orbit insertion (LOI) maneuver. As part of the early phase trajectory design and analysis activities, the required time of flight (TOF) and associated delta-V magnitudes for each recovery maneuver (RM) to recover the KPLO mission trajectory are analyzed. There are two typical trajectory recovery options, direct recovery and low energy recovery. The current work is focused on the direct recovery option. Results indicate that a quicker execution of the first RM after the failure of the first LOI plays a significant role in saving the magnitudes of the RMs. Under the conditions of the extremely tight delta-V budget that is currently allocated for the KPLO mission, it is found that the recovery of the KPLO without altering the originally planned mission orbit (a 100 km circular orbit) cannot be achieved via direct recovery options. However, feasible recovery options are suggested within the boundaries of the currently planned delta-V budget. By changing the shape and orientation of the recovered final mission orbit, it is expected that the KPLO mission may partially pursue its scientific mission after successful recovery, though it will be limited.

Spent fuel reprocessing options

International Nuclear Information System (INIS)

2008-08-01

The objective of this publication is to provide an update on the latest developments in nuclear reprocessing technologies in the light of new developments on the global nuclear scene. The background information on spent fuel reprocessing is provided in Section One. Substantial global growth of nuclear electricity generation is expected to occur during this century, in response to environmental issues and to assure the sustainability of the electrical energy supply in both industrial and less-developed countries. This growth carries with it an increasing responsibility to ensure that nuclear fuel cycle technologies are used only for peaceful purposes. In Section Two, an overview of the options for spent fuel reprocessing and their level of development are provided. A number of options exist for the treatment of spent fuel. Some, including those that avoid separation of a pure plutonium stream, are at an advanced level of technological maturity. These could be deployed in the next generation of industrial-scale reprocessing plants, while others (such as dry methods) are at a pilot scale, laboratory scale or conceptual stage of development. In Section Three, research and development in support of advanced reprocessing options is described. Next-generation spent fuel reprocessing plants are likely to be based on aqueous extraction processes that can be designed to a country specific set of spent fuel partitioning criteria for recycling of fissile materials to advanced light water reactors or fast spectrum reactors. The physical design of these plants must incorporate effective means for materials accountancy, safeguards and physical protection. Section four deals with issues and challenges related to spent fuel reprocessing. The spent fuel reprocessing options assessment of economics, proliferation resistance, and environmental impact are discussed. The importance of public acceptance for a reprocessing strategy is discussed. A review of modelling tools to support the

Comparative availability and reliability assessment of design options for the secondary sodium loops of the EFR

International Nuclear Information System (INIS)

Pamme, H.

1989-01-01

The EFR (European Fast Reactor) project has entered a conceptual study period where different design alternatives are compared concerning feasibility, safety and economic aspects. This paper describes a comparative probabilistic availability and reliability assessment of alternative design options for the secondary sodium loops. These loops will provide heat transfer from the reactor pool to the water-steam (power generating) side. So a high operational availability of the secondary loops during plant lifetime is essential for economic power generation. Additionally a high reliability is required to fulfill the operational decay heat removal function in case of a reactor trip. Availabilities and reliabilities of the different options were assessed using failure mode and effect analysis and the fault tree method. (orig.)

Freight Advanced Traveler Information System (FRATIS) Dallas-Fort Worth : software architecture design and implementation options.

Science.gov (United States)

2013-05-01

This document describes the Software Architecture Design and Implementation Options for FRATIS : system. The demonstration component of this task will serve to test the technical feasibility of the : FRATIS prototype while also facilitating the colle...

Disposition Options for Uranium-233

International Nuclear Information System (INIS)

Beahm, E.C.; Dole, L.R.; Forsberg, C.W.; Icenhour, A.S.; Storch, S.N.

1999-01-01

The U.S. Department of Energy (DOE) Fissile Materials Disposition Program (MD), in support of the U.S. arms-control and nonproliferation policies, has initiated a program to disposition surplus weapons-usable fissile material by making it inaccessible and unattractive for use in nuclear weapons. Weapons-usable fissile materials include plutonium, high-enriched uranium (HEU), and uranium-233 (sup 233)U. In support of this program, Oak Ridge National Laboratory led DOE's contractor efforts to identify and characterize options for the long-term storage and disposal of excess (sup 233)U. Five storage and 17 disposal options were identified and are described herein

Integrated Portfolio Analysis: Return on Investment and Real Options Analysis of Intelligence Information Systems (Cryptologic Carry On Program)

National Research Council Canada - National Science Library

Rios, Jr., Cesar G; Housel, Thomas; Mun, Johnathan

2006-01-01

...) on individual projects, programs, and processes within a portfolio of IT investments. Using KVA historical data as a platform, the authors evaluate potential strategic investments with real options analysis...

Program Theory for Participatory Design

DEFF Research Database (Denmark)

Bossen, Claus; Dindler, Christian; Iversen, Ole Sejer

2018-01-01

How does participatory design work and what are the links between investments in terms of time, people and skills, the processes and the resulting effects? This paper explores program theory as a way for Participatory Design (PD) to investigate and evaluate these issues. Program theory comes out...

Design options for cooperation mechanisms under the new European renewable energy directive

International Nuclear Information System (INIS)

Klessmann, Corinna; Lamers, Patrick; Ragwitz, Mario; Resch, Gustav

2010-01-01

In June 2009, a new EU directive on the promotion of renewable energy sources (RES) entered into effect. The directive 2009/28/EC, provides for three cooperation mechanisms that will allow member states to achieve their national RES target in cooperation with other member states: statistical transfer, joint projects, and joint support schemes. This article analyses the pros and cons of the three mechanisms and explores design options for their implementation through strategic and economic questions: How to counterbalance the major drawbacks of each mechanism? How to reflect a balance of costs and benefits between the involved member states? The analysis identifies a number of design options that respond to these questions, e.g. long term contracts to ensure sufficient flexibility for statistical transfers, a coordinated, standardised joint project approach to increase transparency in the European market, and a stepwise harmonisation of joint support schemes that is based on a cost-effective accounting approach. One conclusion is that the three cooperation mechanisms are closely interlinked. One can consider their relation to be a gradual transition from member state cooperation under fully closed national support systems in case of statistical transfers, to cooperation under fully open national support systems in a joint support scheme.

Availability, reliability and logistic support studies of the RF power system design options for the IFMIF accelerator

Energy Technology Data Exchange (ETDEWEB)

Bargallo, E., E-mail: enric.bargallo-font@upc.edu [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Giralt, A.; Martinez, G. [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Weber, M.; Regidor, D.; Arroyo, J.M. [Centro de Investigaciones Energéticas, Medioambientales y Tecnológicas, Madrid (Spain); Abal, J.; Dies, J.; Tapia, C.; De Blas, A. [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Mendez, P.; Ibarra, A.; Molla, J. [Centro de Investigaciones Energéticas, Medioambientales y Tecnológicas, Madrid (Spain)

2013-10-15

Highlights: ► Current RF system design based on tetrodes chains is evaluated. ► Alternative solid state power amplifiers RF system design is analyzed. ► Both designs are compared in terms of availability, logistics and cost. ► It is concluded that solid state option presents relevant improvements. -- Abstract: The current design of the radio frequency (RF) power system for the International Fusion Materials Irradiation Facility (IFMIF) is based upon tetrodes technology. Due to the improvement in the solid state amplifiers technology, the possibility of using this option for IFMIF RF system is becoming a very competitive alternative presenting from the beginning several advantages in terms of availability, reliability and logistics. The current design based on RF tetrodes chains leads no room for substantial improvements in terms of availability being the requirement for the RF system hard to achieve. The principal goals of this paper are to use RAMI (Reliability, Availability, Maintainability and Inspectionability) analysis in the solid state amplifier design, and to compare the availability, reliability and logistic performances for both alternatives.

Availability, reliability and logistic support studies of the RF power system design options for the IFMIF accelerator

International Nuclear Information System (INIS)

Bargallo, E.; Giralt, A.; Martinez, G.; Weber, M.; Regidor, D.; Arroyo, J.M.; Abal, J.; Dies, J.; Tapia, C.; De Blas, A.; Mendez, P.; Ibarra, A.; Molla, J.

2013-01-01

Highlights: ► Current RF system design based on tetrodes chains is evaluated. ► Alternative solid state power amplifiers RF system design is analyzed. ► Both designs are compared in terms of availability, logistics and cost. ► It is concluded that solid state option presents relevant improvements. -- Abstract: The current design of the radio frequency (RF) power system for the International Fusion Materials Irradiation Facility (IFMIF) is based upon tetrodes technology. Due to the improvement in the solid state amplifiers technology, the possibility of using this option for IFMIF RF system is becoming a very competitive alternative presenting from the beginning several advantages in terms of availability, reliability and logistics. The current design based on RF tetrodes chains leads no room for substantial improvements in terms of availability being the requirement for the RF system hard to achieve. The principal goals of this paper are to use RAMI (Reliability, Availability, Maintainability and Inspectionability) analysis in the solid state amplifier design, and to compare the availability, reliability and logistic performances for both alternatives

Nuclear desalination option for the international reactor innovative and secure (IRIS) design

International Nuclear Information System (INIS)

Ingersoll, D. T.; Binder, J. L.; Conti, D.; Ricotti, M. E.

2004-01-01

The worldwide demand for potable water is on the rise. A recent market survey by the World Resources Institute shows a doubling in desalinated water production every ten years from both seawater and brackish water sources. The production of desalinated water is energy intensive, requiring approximately 3-6 kWh per cubic meter of produced desalted water. At current U.S. water use rates, 1 kW of energy capacity per capita (or 1000 MW for every one million people) would be required to meet water needs with desalted water. The choice of the desalination technology determines the form of energy required: electrical energy for reverse osmosis systems, relatively low quality thermal energy for distillation systems, and both electrical and thermal energy for hybrid systems such as pre-heat RO systems. Nuclear energy plants are attractive for large scale desalination application. Nuclear plants can provide both electrical and thermal energy in an integrated, co-generated fashion to produce a spectrum of energy products including electricity, desalted water, process heat, district heating, and potentially hydrogen generation. A particularly attractive option for nuclear desalination is to couple it with an advanced, modular, passively safe reactor design such as the International Reactor Innovative and Secure (IRIS) plant. This allows for countries with smaller electrical grid needs and infrastructure to add new electrical and desalination capacity in smaller increments and at distributed sites. The safety by design nature of the IRIS reactor will ensure a safe and reliable source of energy even for countries with limited nuclear power experience and infrastructure. Two options for the application of the IRIS nuclear power plant to the cogeneration of electricity and desalted water are presented, including a coupling to a reverse osmosis plant and a multistage flash distillation plant. The results from an economic assessment of the two options are also presented.(author)

When Failure Is Not An Option: Designing Competency-Based Pathways for Next Generation Learning

Science.gov (United States)

Sturgis, Chris; Patrick, Susan

2010-01-01

This exploration into competency-based innovation at the school, district, and state levels suggests that competency-based pathways are a re-engineering of this nation's education system around learning--a re-engineering designed for success in which failure is no longer an option. Competency-based approaches build upon standards reforms, offering…

Designing time-of-use program based on stochastic security constrained unit commitment considering reliability index

International Nuclear Information System (INIS)

Nikzad, Mehdi; Mozafari, Babak; Bashirvand, Mahdi; Solaymani, Soodabeh; Ranjbar, Ali Mohamad

2012-01-01

Recently in electricity markets, a massive focus has been made on setting up opportunities for participating demand side. Such opportunities, also known as demand response (DR) options, are triggered by either a grid reliability problem or high electricity prices. Two important challenges that market operators are facing are appropriate designing and reasonable pricing of DR options. In this paper, time-of-use program (TOU) as a prevalent time-varying program is modeled linearly based on own and cross elasticity definition. In order to decide on TOU rates, a stochastic model is proposed in which the optimum TOU rates are determined based on grid reliability index set by the operator. Expected Load Not Supplied (ELNS) is used to evaluate reliability of the power system in each hour. The proposed stochastic model is formulated as a two-stage stochastic mixed-integer linear programming (SMILP) problem and solved using CPLEX solver. The validity of the method is tested over the IEEE 24-bus test system. In this regard, the impact of the proposed pricing method on system load profile; operational costs and required capacity of up- and down-spinning reserve as well as improvement of load factor is demonstrated. Also the sensitivity of the results to elasticity coefficients is investigated. -- Highlights: ► Time-of-use demand response program is linearly modeled. ► A stochastic model is proposed to determine the optimum TOU rates based on ELNS index set by the operator. ► The model is formulated as a short-term two-stage stochastic mixed-integer linear programming problem.

Designing regulatory frameworks for merchant transmission investments by real options analysis

International Nuclear Information System (INIS)

Pringles, Rolando; Olsina, Fernando; Garcés, Francisco

2014-01-01

In deregulated electricity markets, the transmission network is a key infrastructure for enabling competition in the generation sector. A deficient expansion of the transmission grid prevents the realization of the benefits in terms of efficiency associated with market mechanisms. Consequently, it is essential to provide clear investment policies and economic signals to attract timely and efficient transmission investments in order to develop the system at minimum cost meeting the requirements of generators and consumers, while keeping adequate levels of service quality and reliability. This paper proposes a modern tool of economic evaluation based on real options analysis that provides the regulator the ability to assess various incentives that would lead transmission investors to make efficient decisions in highly uncertain environments. Real options properly values partially irreversible investment decisions, such as to defer, modify or abandon an investment project in response to the arrival of new information or as uncertainties are resolved. Decisions are evaluated from the point of view of a transmission investor trying to maximize its own profits in the time period set to recover the capital invested. The results allow the study of the behavior of transmission investors regarding their decision making when they have the possibility to manage the option to defer, under different regulatory schemes that encourage the expansion of the transmission system. - Highlights: • Regulatory frameworks for efficient and timely transmission expansions are designed. • Irreversibility and uncertainty of transmission investment is properly accounted for. • Response of network investors to regulatory incentives is quantitatively established

Utilizing Design Information in Aspect-Oriented Programming

OpenAIRE

Nagy, I.; Bergmans, Lodewijk; Havinga, W.K.; Aksit, Mehmet; Hirschfeld, Robert; Kowalczyk, Ryszard; Polze, Andreas; Weske, Mathias

2005-01-01

Traditionally in aspect-oriented languages, pointcut designators select joinpoints of a program based on lexical information such as explicit names of program elements. However, this reduces the adaptability of software, since it involves too much information that is hard-coded, and often implementationspecific. We claim that this problem can be reduced by referring to program units through their design intentions. Design intention is represented by annotated design information, which describ...

Traffic Light Options

DEFF Research Database (Denmark)

Jørgensen, Peter Løchte

This paper introduces, prices, and analyzes traffic light options. The traffic light option is an innovative structured OTC derivative developed independently by several London-based investment banks to suit the needs of Danish life and pension (L&P) companies, which must comply with the traffic...... 2006, and supervisory authorities in many other European countries have implemented similar regulation. Traffic light options are therefore likely to attract the attention of a wider audience of pension fund managers in the future. Focusing on the valuation of the traffic light option we set up a Black...... light scenarios. These stress scenarios entail drops in interest rates as well as in stock prices, and traffic light options are thus designed to pay off and preserve sufficient capital when interest rates and stock prices fall simultaneously. Sweden's FSA implemented a traffic light system in January...

Traffic Light Options

DEFF Research Database (Denmark)

Jørgensen, Peter Løchte

2007-01-01

This paper introduces, prices, and analyzes traffic light options. The traffic light option is an innovative structured OTC derivative developed independently by several London-based investment banks to suit the needs of Danish life and pension (L&P) companies, which must comply with the traffic...... 2006, and supervisory authorities in many other European countries have implemented similar regulation. Traffic light options are therefore likely to attract the attention of a wider audience of pension fund managers in the future. Focusing on the valuation of the traffic light option we set up a Black...... light scenarios. These stress scenarios entail drops in interest rates as well as in stock prices, and traffic light options are thus designed to pay off and preserve sufficient capital when interest rates and stock prices fall simultaneously. Sweden's FSA implemented a traffic light system in January...

Optimization of FRAP uncertainty analysis option

International Nuclear Information System (INIS)

Peck, S.O.

1979-10-01

The automated uncertainty analysis option that has been incorporated in the FRAP codes (FRAP-T5 and FRAPCON-2) provides the user with a means of obtaining uncertainty bands on code predicted variables at user-selected times during a fuel pin analysis. These uncertainty bands are obtained by multiple single fuel pin analyses to generate data which can then be analyzed by second order statistical error propagation techniques. In this process, a considerable amount of data is generated and stored on tape. The user has certain choices to make regarding which independent variables are to be used in the analysis and what order of error propagation equation should be used in modeling the output response. To aid the user in these decisions, a computer program, ANALYZ, has been written and added to the uncertainty analysis option package. A variety of considerations involved in fitting response surface equations and certain pit-falls of which the user should be aware are discussed. An equation is derived expressing a residual as a function of a fitted model and an assumed true model. A variety of experimental design choices are discussed, including the advantages and disadvantages of each approach. Finally, a description of the subcodes which constitute program ANALYZ is provided

Nevada Transportation Options Study

International Nuclear Information System (INIS)

P. GEHNER; E.M. WEAVER; L. FOSSUM

2006-01-01

This study performs a cost and schedule analysis of three Nevada Transportation options that support waste receipt at the repository. Based on the U.S. Department of Energy preference for rail transportation in Nevada (given in the Final Environmental Impact Statement), it has been assumed that a branch rail line would be constructed to support waste receipt at the repository. However, due to potential funding constraints, it is uncertain when rail will be available. The three Nevada Transportation options have been developed to meet a varying degree of requirements for transportation and to provide cost variations used in meeting the funding constraints given in the Technical Direction Letter guidelines for this study. The options include combinations of legal-weight truck, heavy-haul truck, and rail. Option 1 uses a branch rail line that would support initial waste receipt at the repository in 2010. Rail transportation would be the primary mode, supplemented by legal weight trucks. This option provides the highest level of confidence in cost and schedule, lowest public visibility, greatest public acceptability, lowest public dose, and is the recommended option for support of waste receipt. The completion of rail by 2010 will require spending approximately $800 million prior to 2010. Option 2 uses a phased rail approach to address a constrained funding scenario. To meet funding constraints, Option 2 uses a phased approach to delay high cost activities (final design and construction) until after initial waste receipt in 2010. By doing this, approximately 95 percent of the cost associated with completion of a branch rail line is deferred until after 2010. To support waste receipt until a branch rail line is constructed in Nevada, additional legal-weight truck shipments and heavy-haul truck shipments (on a limited basis for naval spent nuclear fuel) would be used to meet the same initial waste receipt rates as in Option 1. Use of heavy-haul shipments in the absence

Role and design options of a logistics vehicle to support European and international space infrastructures in low earth orbit

Science.gov (United States)

Apel, U.; Ress, R.

1991-10-01

Design options for a low-cost logistic vehicle for transporting uploads in LEO are discussed. Preferable design features based on mission requirements and constraints are identified and it is shown that the ATV currently under study has a suitable design for such a vehicle.

Integrating computer programs for engineering analysis and design

Science.gov (United States)

Wilhite, A. W.; Crisp, V. K.; Johnson, S. C.

1983-01-01

The design of a third-generation system for integrating computer programs for engineering and design has been developed for the Aerospace Vehicle Interactive Design (AVID) system. This system consists of an engineering data management system, program interface software, a user interface, and a geometry system. A relational information system (ARIS) was developed specifically for the computer-aided engineering system. It is used for a repository of design data that are communicated between analysis programs, for a dictionary that describes these design data, for a directory that describes the analysis programs, and for other system functions. A method is described for interfacing independent analysis programs into a loosely-coupled design system. This method emphasizes an interactive extension of analysis techniques and manipulation of design data. Also, integrity mechanisms exist to maintain database correctness for multidisciplinary design tasks by an individual or a team of specialists. Finally, a prototype user interface program has been developed to aid in system utilization.

Double degree master program: Optical Design

Science.gov (United States)

Bakholdin, Alexey; Kujawinska, Malgorzata; Livshits, Irina; Styk, Adam; Voznesenskaya, Anna; Ezhova, Kseniia; Ermolayeva, Elena; Ivanova, Tatiana; Romanova, Galina; Tolstoba, Nadezhda

2015-10-01

Modern tendencies of higher education require development of master programs providing achievement of learning outcomes corresponding to quickly variable job market needs. ITMO University represented by Applied and Computer Optics Department and Optical Design and Testing Laboratory jointly with Warsaw University of Technology represented by the Institute of Micromechanics and Photonics at The Faculty of Mechatronics have developed a novel international master double-degree program "Optical Design" accumulating the expertise of both universities including experienced teaching staff, educational technologies, and experimental resources. The program presents studies targeting research and professional activities in high-tech fields connected with optical and optoelectronics devices, optical engineering, numerical methods and computer technologies. This master program deals with the design of optical systems of various types, assemblies and layouts using computer modeling means; investigation of light distribution phenomena; image modeling and formation; development of optical methods for image analysis and optical metrology including optical testing, materials characterization, NDT and industrial control and monitoring. The goal of this program is training a graduate capable to solve a wide range of research and engineering tasks in optical design and metrology leading to modern manufacturing and innovation. Variability of the program structure provides its flexibility and adoption according to current job market demands and personal learning paths for each student. In addition considerable proportion of internship and research expands practical skills. Some special features of the "Optical Design" program which implements the best practices of both Universities, the challenges and lessons learnt during its realization are presented in the paper.

Technology Development Program for an Advanced Potassium Rankine Power Conversion System Compatible with Several Space Reactor Designs

Energy Technology Data Exchange (ETDEWEB)

Yoder, G.L.

2005-10-03

This report documents the work performed during the first phase of the National Aeronautics and Space Administration (NASA), National Research Announcement (NRA) Technology Development Program for an Advanced Potassium Rankine Power Conversion System Compatible with Several Space Reactor Designs. The document includes an optimization of both 100-kW{sub e} and 250-kW{sub e} (at the propulsion unit) Rankine cycle power conversion systems. In order to perform the mass optimization of these systems, several parametric evaluations of different design options were investigated. These options included feed and reheat, vapor superheat levels entering the turbine, three different material types, and multiple heat rejection system designs. The overall masses of these Nb-1%Zr systems are approximately 3100 kg and 6300 kg for the 100- kW{sub e} and 250-kW{sub e} systems, respectively, each with two totally redundant power conversion units, including the mass of the single reactor and shield. Initial conceptual designs for each of the components were developed in order to estimate component masses. In addition, an overall system concept was presented that was designed to fit within the launch envelope of a heavy lift vehicle. A technology development plan is presented in the report that describes the major efforts that are required to reach a technology readiness level of 6. A 10-year development plan was proposed.

42 CFR 408.65 - Payment options.

Science.gov (United States)

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Payment options. 408.65 Section 408.65 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES MEDICARE PROGRAM PREMIUMS FOR SUPPLEMENTARY MEDICAL INSURANCE Direct Remittance: Individual Payment § 408.65 Payment options...

Fuel channel in-service inspection programs program design for maximum cost effectiveness

International Nuclear Information System (INIS)

Van den Brekel, N.C.

1995-01-01

Inspection is an integral part of fuel channel life management strategy. Inspection data is used to assess the state of reactor core integrity and provide the information necessary to optimize long term maintenance programs. This paper will provide an overview of the structured approach to developing fuel channel inspection programs within OHN. The inspection programs are designed to balance the resources utilized (cost, outage time, and dose expenditure) with the benefits provided by the inspection data obtained (improved knowledge of component status, degradation mechanisms and rates, etc..). The CANDU community has yet to have a fuel channel operate for a full 30 year design life. Since research programs can not fully simulate reactor operating conditions, inspections become an essential feature of the life management strategy as the components age. Inspection programs often include activities designed to develop predictive capability for long term fuel channel behaviour and provide early warning of changes in behaviour. It should be noted that although this paper addresses the design of fuel channel inspection programs, the basic principles presented can be applied to the design of inspection programs for any major power plant component or system. (author)

Nuclear Engine System Simulation (NESS). Version 2.0: Program user's guide. Final Report

International Nuclear Information System (INIS)

Pelaccio, D.G.; Scheil, C.M.; Petrosky, L.

1993-03-01

This Program User's Guide discusses the Nuclear Thermal Propulsion (NTP) engine system design features and capabilities modeled in the Nuclear Engine System Simulation (NESS): Version 2.0 program (referred to as NESS throughout the remainder of this document), as well as its operation. NESS was upgraded to include many new modeling capabilities not available in the original version delivered to NASA LeRC in Dec. 1991, NESS's new features include the following: (1) an improved input format; (2) an advanced solid-core NERVA-type reactor system model (ENABLER 2); (3) a bleed-cycle engine system option; (4) an axial-turbopump design option; (5) an automated pump-out turbopump assembly sizing option; (6) an off-design gas generator engine cycle design option; (7) updated hydrogen properties; (8) an improved output formnd (9) personal computer operation capability. Sample design cases are presented in the user's guide that demonstrate many of the new features associated with this upgraded version of NESS, as well as design modeling features associated with the original version of NESS

The research for flexible product family manufacturing based on real options

Directory of Open Access Journals (Sweden)

Maozhu Jin

2015-01-01

Full Text Available Purpose: The goal of this paper is to find the best production strategy for product mix, which means the largest value of the options. And finally, give a case and find the solution of the optimal production strategy for product mix. Design/methodology/approach: This article, based on the production with characteristics of a call option and 0-1 integer programming model, build new-products mix strategy, and through case demonstrate that traditional method underestimates the value of the products mix. Finding: According to market being volatility and uncertainty and the production can being delayed, firms can flexibly arrange the best time for products to manufacture. Use real options theory to analyze product decision and the best production timing decision. Find the total options value is higher than the traditional methods. Research limitations/implications: We are not applied to real option pricing theory in modular flexible production system. We just applied real option pricing theory to the product platform. The basic model needs to improve. While the thinking of this paper provides some research ideas for flexible production systems based on real option in further research. Practical Implications: The introduction of the real option make the company can achieve dynamic planning and flexible management for production of products mix and get the better benefit. Originality/value: The central contribution of this paper is to introduce the option mechanism in the production timing for the product mix.

Computer Program Re-layers Engineering Drawings

Science.gov (United States)

Crosby, Dewey C., III

1990-01-01

RULCHK computer program aids in structuring layers of information pertaining to part or assembly designed with software described in article "Software for Drawing Design Details Concurrently" (MFS-28444). Checks and optionally updates structure of layers for part. Enables designer to construct model and annotate its documentation without burden of manually layering part to conform to standards at design time.

Market Aspects of an Interior Design Program.

Science.gov (United States)

Gold, Judy E.

A project was conducted to evaluate a proposed interior design program in order to determine the marketability (job availability in the field of interior design and home furnishings merchandising) and the feasibility (educational requirements for entrance into the interior design and home furnishings merchandising job market) of the program. To…

Study of the Cherokee Nuclear Station: projected impacts, monitoring plan, and mitigation options for Cherokee County, South Carolina

International Nuclear Information System (INIS)

Peelle, E.; Schweitzer, M.; Scharre, P.; Pressman, B.

1979-07-01

This report inventories Cherokee County's capabilities and CNS project characteristics, projects expected impacts from the interaction of the two defines four options for Cherokee County decision makers, and presents a range of possible mitigation and monitoring plans for dealing with the problems identified. The four options and general implementation guidelines for each are presented after reviewing pertinent features of other mitigation and monitoring plans. The four options include (1) no action, (2) preventing impacts by preventing growth, (3) selective growth in designated areas as services can be supplied, and (4) maximum growth designed to attract as many in-movers as possible through a major program of capital investiments in public and private services. With the exception of the no action option, all plans deal with impacts according to some strategy determined by how the County wishes to manage growth. Solutions for impact problems depend on which growth strategy is selected and what additional resources are secured during the impact period. A monitoring program deals with the problems of data and projections uncertainty, while direct action is proposed to deal with the institutional problems of delay of the needed access road, timeing and location problems from the tax base mismatch, and lack of local planning capability

Study of the Cherokee Nuclear Station: projected impacts, monitoring plan, and mitigation options for Cherokee County, South Carolina

Energy Technology Data Exchange (ETDEWEB)

Peelle, E.; Schweitzer, M.; Scharre, P.; Pressman, B.

1979-07-01

This report inventories Cherokee County's capabilities and CNS project characteristics, projects expected impacts from the interaction of the two defines four options for Cherokee County decision makers, and presents a range of possible mitigation and monitoring plans for dealing with the problems identified. The four options and general implementation guidelines for each are presented after reviewing pertinent features of other mitigation and monitoring plans. The four options include (1) no action, (2) preventing impacts by preventing growth, (3) selective growth in designated areas as services can be supplied, and (4) maximum growth designed to attract as many in-movers as possible through a major program of capital investiments in public and private services. With the exception of the no action option, all plans deal with impacts according to some strategy determined by how the County wishes to manage growth. Solutions for impact problems depend on which growth strategy is selected and what additional resources are secured during the impact period. A monitoring program deals with the problems of data and projections uncertainty, while direct action is proposed to deal with the institutional problems of delay of the needed access road, timeing and location problems from the tax base mismatch, and lack of local planning capability.

CANDU fuel cycle options in Korea

International Nuclear Information System (INIS)

Boczar, P. G.; Fehrenbach, P. J.; Meneley, D. A.

1996-01-01

There are many reasons for countries embarking on a CANDU R program to start with the natural uranium fuel cycle. Simplicity of fuel design, ease of fabrication, and ready availability of natural uranium all help to localize the technology and to reduce reliance on foreign technology. Nonetheless, at some point, the incentives for using natural uranium fuel may be outweighed by the advantages of alternate fuel cycles. The excellent neutron economy, on-line refuelling, and simple fuel-bundle design provide an unsurpassed degree of fuel-cycle flexibility in CANDU reactors. The easiest first step in CANDU fuel-cycle evolution may be the use of slightly enriched uranium (SEU), including recovered uranium from reprocessed LWR spent fuel. Relatively low enrichment (up to 1.2%) will result in a two- to three-fold reduction in the quantity of spent fuel per unit energy production, reductions in fuel-cycle costs, and greater flexibility in the design of new reactors. The CANFLEX (CANDU FLEXible) fuel bundle would be the optimal fuel carrier. A country that has both CANDU and PWR reactors can exploit the natural synergism between these two reactor types to minimize overall waste production, and maximize energy derived from the fuel. This synergism can be exploited through several different fuel cycles. A high burnup CANDU MOX fuel design could be used to utilize plutonium from conventional reprocessing or more advanced reprocessing options (such as co-processing). DUPIC (Direct Use of Spent PWR Fuel In CANDU) represents a recycle option that has a higher degree of proliferation resistance than dose conventional reprocessing, since it uses only dry processes for converting spent PWR fuel into CANDU fuel, without separating the plutonium. Good progress is being made in the current KAERI, AECL, and U. S. Department of State program in demonstrating the technical feasibility of DUPIC. In the longer term, CANDU reactors offer even more dramatic synergistic fuel cycles with PWR or

Design options to minimize tritium inventories at Savannah River

Energy Technology Data Exchange (ETDEWEB)

Klein, J.E., E-mail: james.klein@srnl.doe.gov; Wilson, J.; Heroux, K.J.; Poore, A.S.; Babineau, D.W.

2016-11-01

Highlights: • La-Ni-Al alloys are used as tritium storage materials and retain He-3. • La-Ni-Al He-3 effects decrease useable process tritium inventory. • Use of Pd or depleted uranium beds decreases process tritium inventories. • Reduced inventory tritium facilities will lower public risk. - Abstract: Large quantities of tritium are stored and processed at the Savannah River Site (SRS) Tritium Facilities. In many design basis accidents (DBAs), it is assumed the entire tritium inventory of the in-process vessels are released from the facility and the site for inclusion in public radiological dose calculations. Pending changes in public dose calculation methodologies are driving the need for smaller in-process tritium inventories to be released during DBAs. Reducing the in-process tritium inventory will reduce the unmitigated source term for public dose calculations and will also reduce the production demand for a lower inventory process. This paper discusses process design options to reduce in-process tritium inventories. A Baseline process is defined to illustrate the impact of removing or replacing La-Ni-Al alloy tritium storage beds with palladium (Pd) or depleted uranium (DU) storage beds on facility in-process tritium inventories. Elimination of La-Ni-Al alloy tritium storage beds can reduce in-process tritium inventories by over 1.5 kg, but alternate process technologies may needed to replace some functions of the removed beds.

Design options to minimize tritium inventories at Savannah River

International Nuclear Information System (INIS)

Klein, J.E.; Wilson, J.; Heroux, K.J.; Poore, A.S.; Babineau, D.W.

2016-01-01

Highlights: • La-Ni-Al alloys are used as tritium storage materials and retain He-3. • La-Ni-Al He-3 effects decrease useable process tritium inventory. • Use of Pd or depleted uranium beds decreases process tritium inventories. • Reduced inventory tritium facilities will lower public risk. - Abstract: Large quantities of tritium are stored and processed at the Savannah River Site (SRS) Tritium Facilities. In many design basis accidents (DBAs), it is assumed the entire tritium inventory of the in-process vessels are released from the facility and the site for inclusion in public radiological dose calculations. Pending changes in public dose calculation methodologies are driving the need for smaller in-process tritium inventories to be released during DBAs. Reducing the in-process tritium inventory will reduce the unmitigated source term for public dose calculations and will also reduce the production demand for a lower inventory process. This paper discusses process design options to reduce in-process tritium inventories. A Baseline process is defined to illustrate the impact of removing or replacing La-Ni-Al alloy tritium storage beds with palladium (Pd) or depleted uranium (DU) storage beds on facility in-process tritium inventories. Elimination of La-Ni-Al alloy tritium storage beds can reduce in-process tritium inventories by over 1.5 kg, but alternate process technologies may needed to replace some functions of the removed beds.

CANDU fuel cycle options in Korea

International Nuclear Information System (INIS)

Boczar, P.G.; Fehrenbach, P.J.; Meneley, D.A.

1996-04-01

The easiest first step in CANDU fuel-cycle evolution may be the use of slightly enriched uranium (SEU), including recovered uranium from reprocessed LWR spent fuel. Relatively low enrichment (up to 1.2%) will result in a twoto three-fold reduction in the quantity of spent fuel per unit energy production, reductions in fuel-cycle costs, and greater flexibility in the design of new reactors. The CANFLEX (CANDU FLEXible) fuel bundle would be the optimal fuel carrier. A country that has both CANDU and PWR reactors can exploit the natural synergism between these two reactor types to minimize overall waste production, and maximize energy derived from the fuel. This synergism can be exploited through several different fuel cycles. A high burnup CANDU MOX fuel design could be used to utilize plutonium from conventional reprocessing or more advanced reprocessing options (such as co-processing). DUPIC (Direct Use of Spent PWR Fuel In CANDU) represents a recycle option that has a higher degree of proliferation resistance than does conventional reprocessing, since it uses only dry processes for converting spent PWR fuel into CANDU fuel, without separating the plutonium. Good progress is being made in the current KAERI, AECL, and U.S. Department of State program in demonstrating the technical feasibility of DUPIC. In the longer term, CANDU reactors offer even more dramatic synergistic fuel cycles with PWR or FBR reactors. If the objective of a national fuel-cycle program is the minimization of actinide waste or destruction of long-lived fission products, then studies have shown the superiority of CANDU reactors in meeting this objective. Long-term energy security can be assured either through the thorium cycle or through a CANDU 1 FBR system, in which the FBR would be operated as a 'fuel factory,' providing the fissile material to power a number of lower-cost, high efficiency CANDU reactors. In summary, the CANDU reactor's simple fuel design, high neutron economy, and on

French programs for advanced waste management options

Energy Technology Data Exchange (ETDEWEB)

Salvatores, M [CEA-DRN (France); Schapira, J P [CNRS-IN2P3 (France); Mouney, H [EDF-DE (France)

1997-11-01

Several organisms (CEA, CNRS, EdF, etc.) are cooperating in France on Accelerator-Driven Systems (ADS). The major motivation is the investigation of innovative options for the radioactive waste management. The paper describes the ongoing activities and future directions of this cooperative effort in the field of ADS. 11 refs, 3 figs.

New Fathers' Perinatal Depression and Anxiety-Treatment Options: An Integrative Review.

Science.gov (United States)

O'Brien, Anthony P; McNeil, Karen A; Fletcher, Richard; Conrad, Agatha; Wilson, Amanda J; Jones, Donovan; Chan, Sally W

2017-07-01

More than 10% of fathers experience depression and anxiety during the perinatal period, but paternal perinatal depression (PPND) and anxiety have received less attention than maternal perinatal mental health problems. Few mainstream treatment options are available for men with PPND and anxiety. The aim of this literature review was to summarize the current understanding of PPND and the treatment programs specifically designed for fathers with perinatal depression. Eight electronic databases were searched using a predefined strategy, and reference lists were also hand searched. PPND and anxiety were identified to have a negative impact on family relationships, as well as the health of mothers and children. Evidence suggests a lack of support and tailored treatment options for men having trouble adjusting to the transition to fatherhood. Of the limited options available, cognitive behavioral therapy, group work, and blended delivery programs, including e-support approaches appear to be most effective in helping fathers with perinatal depression and anxiety. The review findings have important implications for the understanding of PPND and anxiety. Future research is needed to address the adoption of father-inclusive and father-specific models of care to encourage fathers' help-seeking behavior. Inclusion of male-specific requirements into support and treatment options can improve the ability of services to engage new fathers. Psychotherapeutic intervention could assist to address the cognitive differences and dissonance for men adjusting to the role of father, including male identity and role expectations.

42 CFR 438.356 - State contract options.

Science.gov (United States)

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false State contract options. 438.356 Section 438.356 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS MANAGED CARE External Quality Review § 438.356 State contract options...

Type Soundness in the Dart Programming Language

DEFF Research Database (Denmark)

Strocco, Fabio

Many mainstream programming languages are dynamically typed. This allows for rapid software development and programming flexibility because it gives programmers the freedom to use powerful programming patterns that are not allowed in statically typed programming languages. Nevertheless......, this freedom does not come without drawbacks: static bugs detection, IDE support, and compiler optimization techniques are harder to implement. In the last decades, the research literature and mainstream programming languages have been aiming to reach a trade-off between statically typed and dynamically typed...... languages. We investigate the trade-off, focusing on the area of optional typing, which allows programmers to choose when to use static type checking in parts of pro- grams. Our primary focus is Dart, an optionally typed programming language with a type system that is unsound by design. What makes Dart...

Designing an orientation program for new faculty.

Science.gov (United States)

Holyfield, Lavern J; Berry, Charles W

2008-12-01

The Faculty Development Committee (FDC) at Baylor College of Dentistry (BCD) is charged with providing programs and activities that facilitate the success of existing faculty in the constantly changing environment of academia. In response to concerns regarding the challenges wrought by current and projected shortages of dental faculty across the nation, the FDC was prompted to assess development opportunities available to BCD faculty. A professional development resource that we found deficient was a formal, comprehensive orientation program for newly hired faculty. To guide the efforts of the committee in developing this program, a survey was designed and administered during an annual faculty retreat. Respondents were new and junior faculty, senior faculty, and some administrators. The results of the survey to determine requirements for new faculty orientation became the basis for formalizing BCD's new faculty orientation program. This article provides an overview of the new faculty orientation process from design to program implementation and describes the development and use of a faculty survey to determine the fundamental elements of a faculty development program, identification of essential individuals for designing/implementing the program, and implementation of a new faculty orientation program at BCD.

Structured Design Language for Computer Programs

Science.gov (United States)

Pace, Walter H., Jr.

1986-01-01

Box language used at all stages of program development. Developed to provide improved productivity in designing, coding, and maintaining computer programs. BOX system written in FORTRAN 77 for batch execution.

Electronic automation of LRFD design programs.

Science.gov (United States)

2010-03-01

The study provided electronic programs to WisDOT for designing pre-stressed girders and piers using the Load : Resistance Factor Design (LRFD) methodology. The software provided is intended to ease the transition to : LRFD for WisDOT design engineers...

Hinterbrand Lodge Outdoor Education Center. Program Information.

Science.gov (United States)

Dependents Schools (DOD), Washington, DC. European Area.

Describing Department of Defense Dependents Schools Europe (DODDSEUR) use of Hinterbrand Lodge Outdoor Education Center, this document is directed to sponsors wishing to take groups to Hinterbrand for one or more of the five program options (outdoor education week, teacher weekend, school-designed outdoor education program, administrative faculty…

Summary report on focusing HTGR technology programs

International Nuclear Information System (INIS)

The program effort to focus technology development activities consists of work in three areas: the identification of Reference Plant Options; the identification of design data needs and supporting program requirements for these plants; and the development of management plans and tools consistent with the execution of candidate systems

Centralized vs decentralized options for an European Data Relay Satellite system

Science.gov (United States)

Saint Aubert, S.; Hervieux, M.; Perbos, J. L.; Saggese, E.; Soprano, C.

1985-10-01

The European Data Relay Satellite (DRS) is now being planned to support future European missions in the nineties and in particular the various elements of the in-orbit infrastructure. Studies are being conducted to investigate the usefulness of the relay system as well as to provide the basis for issuing technical specifications for a development and launch in 1993. This paper presents the results of a study issued by ESA on possible options for a DRS System, concentrating on the comparison between a centralized and a decentralized data distribution concept. After recalling the space programs foreseen in Europe, the paper discusses the architecture and design of the various elements of the System: space segment, DRS ground segment, and user ground segment for different options of data dissemination.

Mathematical programming models for the economic design and assessment of wind energy conversion systems

Science.gov (United States)

Reinert, K. A.

The use of linear decision rules (LDR) and chance constrained programming (CCP) to optimize the performance of wind energy conversion clusters coupled to storage systems is described. Storage is modelled by LDR and output by CCP. The linear allocation rule and linear release rule prescribe the size and optimize a storage facility with a bypass. Chance constraints are introduced to explicitly treat reliability in terms of an appropriate value from an inverse cumulative distribution function. Details of deterministic programming structure and a sample problem involving a 500 kW and a 1.5 MW WECS are provided, considering an installed cost of $1/kW. Four demand patterns and three levels of reliability are analyzed for optimizing the generator choice and the storage configuration for base load and peak operating conditions. Deficiencies in ability to predict reliability and to account for serial correlations are noted in the model, which is concluded useful for narrowing WECS design options.

Identification of the real options in a program of nuclear plants

International Nuclear Information System (INIS)

Camacho G, D.; Diaz N, M. J.; Reinking C, A.

2008-01-01

The development of our societies and our economies this intimately related to electric power and this as well with the generating sources, due to the projection of world-wide growth should go associate with a strategy of growth of energy generation. Considering to the nuclear power as an option to satisfy the energy needs that a country can provide two main immediate benefits: The stabilization of prices of security of provision of electric power of the nation. The care of the environment, since the gas discharges greenhouse are almost null. At the moment nuclear energy represents economically a viable option for the capital investment, taking into account the development from technology, the policies implemented by the state and the prices of other fuels. Due to the great investment that its require for the nuclear plants are necessary to use financial tools that allow to analyze the future scenes in which ours investment can be seen affected and to value the flexibility of being able to enlarge, to postpone or to stop our project in order to have majors profits or to diminish the lost ones. This valuation of the flexibility can be obtained from the called method Real Options. By analysis of Real Options the process is understood to apply to the methodology of the Financial Options to the valuation of projects or the management of real assets. The Real Options appear in flexible plans, projects, activities or enterprise investments, like for example, to leave or to sell the investment project before concluding it, changing to their use or its technology, to prolong their life, the option to choose, one or the other capacity, among others possibilities. In this work is an example of the application of the method of Real Options in the decision to invest or to defer the investment for the construction of a nuclear plant following the behavior of the tariffs in the market or the costs of generation of other technologies with which a nuclear plant competes. (Author)

Options for human intrusion

International Nuclear Information System (INIS)

Bauser, M.; Williams, R.

1993-01-01

This paper addresses options for dealing with human intrusion in terms of performance requirements and repository siting and design requirements. Options are presented, along with the advantages and disadvantages of certain approaches. At the conclusion, a conceptual approach is offered emphasizing both the minimization of subjective judgements concerning future human activity, and specification of repository requirements to minimize the likelihood of human intrusion and any resulting, harmful effects should intrusion occur

Nuclear Option in Korea

International Nuclear Information System (INIS)

Han, K. I.

2002-01-01

With sixteen(16) operating nuclear units in Korea, the share of nuclear power generation reached 41% of the total electric power generation as of December 2000. A prediction is that it would further increase to 44.5% by year 2015 according to the national long term power development plan. Four units are currently under construction with 6 more units in order. With little domestic energy resource and increasing energy demand to support national economic growth, Korea has chosen nuclear power as one of the major energy sources to ensure stable power supply and to promote energy self-sufficiency. It has been recognized that nuclear power in Korea is not a selective option but rather a necessity. The Korean nuclear power development started with construction of a 600 MWe size reactor that was designed and constructed by foreign vendors. As the national grid capacity became larger, the size of nuclear units increased to 1000 MWe class. In the mean time, the need for nuclear technology self-reliance grew not only in operation and maintenance but also in construction, manufacturing and design. For this, a nuclear technology self-reliance program has been embarked with the support of the Government and utility, and the 1000 MWe class KSNP(Korean Standard Nuclear Power Plant) has been developed. The KSNPs are currently being designed, manufactured, constructed and operated by relevant Korean entities themselves. To fit into a larger capacity national grid and also to improve nuclear economic competitiveness, the 1400 MWe class KNGR(Korean Next Generation Reactor) design has been developed uprating the 1000 MWe KSNP design. Its construction project is currently under contract negotiation, and is planned to be finished by 2010. In the mean time, to be ready for future electric power market deregulation, the 600 MWe class small KSNP design is being developed downsizing the KSNP. A modular small size reactor, SMART(System Integrated Modular Advanced Reactor) is also being

Designing viable cropping options for salt-affected lands

Science.gov (United States)

Shabala, Sergey; Meinke, Holger

2017-04-01

Salinity cost agricultural sector over 27Bln pa in lost opportunities and is an issue that crosses all spatial and temporal scales - from individual fields, farms, catchments, landscapes to national and global levels. Salinity manifests itself in many forms and often leads to further soil degradation such as erosion, nutrient and soil organic matter depletion, and a loss of (soil) biodiversity. Salinity may also cause major disturbance to ecosystems due to its impact on resources (e.g. pollution of aquifers). In extreme cases it can turn previously highly productive areas into wastelands. An increasing global population and unprecedented urban sprawls are now putting additional pressures on our soil and water resources, particularly in regions where urbanisation directly competes with agriculture for access to land and water. And although everyone agrees that avoiding soil salinity in the first instance would be the most effective way of combating it, reality is that the amount of saline land and water resources is rapidly increasing, and will continue to increase, especially in developing countries. Purposefully designing our cropping systems that can cope with various levels of salinity could be one answer to this increasing problem. In this work we review some of the key cropping options that can be deployed to either avoid, reduce or remediate salt-affected lands. We argue that for these measures to be most effective an ongoing science - policy - society dialogue is required to ensure that policy frameworks that govern land and water management are conducive to reducing salinity or even assist in restoring affected areas. We first consider several case studies highlighting the extent of the problem using ongoing salinity hotspots around the globe. We then look at halophytes as a possible biological tools to remediate already saline sols, and discuss prospects of mixed (halophytes and glycophytes) cropping solutions for various agricultural systems at different

24 CFR 982.630 - Homeownership option: Homeownership counseling.

Science.gov (United States)

2010-04-01

... counseling. 982.630 Section 982.630 Housing and Urban Development Regulations Relating to Housing and Urban... Types Homeownership Option § 982.630 Homeownership option: Homeownership counseling. (a) Before... pre-assistance homeownership and housing counseling program required by the PHA (pre-assistance...

A real-life example of choosing an inherently safer process option

International Nuclear Information System (INIS)

Study, Karen

2007-01-01

While choosing an inherently safer alternative may seem straightforward, sometimes what seems to be the most obvious alternative may not provide the best risk reduction. The process designer must maintain a broad perspective to be able to recognize all potential hazards when evaluating design options. All aspects of operation such as start-up, shut-down, utility failure, as well as normal operation should be considered. Choosing the inherently safer option is best accomplished early in the option selection phase of a project; however, recycle back to the option selection phase may be needed if an option is not thoroughly evaluated early in the process. In this paper, a project to supply ammonia to a catalytic reactor will be reviewed. During the course of the project, an 'inherently safer' alternative was selected and later discarded due to issues uncovered during the detail design phase. The final option chosen will be compared to (1) the original design and (2) the initial 'inherently safer' alternative. The final option was inherently safer than both the original design and the initial 'inherently safer' alternative even though the design team initially believed that it would not be

38 CFR 9.4 - Beneficiaries and options.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Beneficiaries and options... SERVICEMEMBERS' GROUP LIFE INSURANCE AND VETERANS' GROUP LIFE INSURANCE § 9.4 Beneficiaries and options. Any designation of beneficiary or election of settlement options is subject to the provisions of 38 U.S.C. 1970...

Life-cycle cost analysis of energy efficiency design options for residential furnaces and boilers

International Nuclear Information System (INIS)

Lutz, James; Lekov, Alex; Chan, Peter; Whitehead, Camilla Dunham; Meyers, Steve; McMahon, James

2006-01-01

In 2001, the US Department of Energy (DOE) initiated a rulemaking process to consider whether to amend the existing energy efficiency standards for furnaces and boilers. A key factor in DOE's consideration of new standards is the economic impacts on consumers of possible revisions to energy-efficiency standards. Determining cost-effectiveness requires an appropriate comparison of the additional first cost of energy efficiency design options with the savings in operating costs. DOE's preferred approach involves comparing the total life-cycle cost (LCC) of owning and operating a more efficient appliance with the LCC for a baseline design. This study describes the method used to conduct the LCC analysis and presents the estimated change in LCC associated with more energy-efficient equipment. The results indicate that efficiency improvement relative to the baseline design can reduce the LCC in each of the product classes considered

Newborn screening for congenital cytomegalovirus: Options for hospital-based and public health programs.

Science.gov (United States)

Grosse, Scott D; Dollard, Sheila; Ross, Danielle S; Cannon, Michael

2009-12-01

Congenital cytomegalovirus (CMV) infection is a leading cause of sensorineural hearing loss (SNHL) and developmental disability in children. Early identification of infected children through screening could allow for early intervention and improvement in functional outcomes among the subset who develop sequelae. To outline potential options and strategies for screening newborns for congenital CMV infection and to discuss barriers to screening and data needs to inform future policy decisions. Commentary based on the literature and expert opinion on newborn dried blood spot screening, newborn hearing screening/Early Hearing Detection and Intervention (EHDI) programs, and congenital CMV. Although no population-based screening for congenital CMV is underway, pilot newborn screening studies using a variety of assays with urine or dried blood spot specimens are underway. Challenges to screening are both practical-uncertain sensitivity of blood spot assays suitable for large-scale screening and lack of infrastructure for collection of urine specimens; and evidentiary-the need to demonstrate improved outcomes and value of screening to offset the expense and potential adverse psychosocial consequences for children and families whose children require periodic monitoring but never develop sequelae. Screening for congenital CMV infection is a potentially important intervention that merits additional research, including the logistical feasibility of different screening options and psychosocial consequences for families.

Development of design program for air handling units

Energy Technology Data Exchange (ETDEWEB)

Ham, J. K.; Kim, J. H.; Kim, Y. K.; Kim, Y. I.; Kang, P. Y. [Hyundai Heavy Industries Co., Ltd., Ulsan (Korea, Republic of)

2000-07-01

An Air Handling Unit(AHU) has been usually designed by manual calculations. Drawing works together with design calculations should be redone for every designing work, and also be needed to make some corrections of them. In order to design the AHU more efficiently, an AHU program has been developed. The developed program on the Windows environment is operated by the Graphic User Interface(GUI) realized using the Visual Basic Interpreter. The program provides calculation sheet of coils, weights and pressures in a MS-Excel file format as well as design drawing of the AHU in a auto CAD file format idealized by AutoLISP. Those files of the commercial softwares make easier for a designer to transfer design results to the another company for bid via e-mail.

Development of design program for air handling units

International Nuclear Information System (INIS)

Ham, J. K.; Kim, J. H.; Kim, Y. K.; Kim, Y. I.; Kang, P. Y.

2000-01-01

An Air Handling Unit(AHU) has been usually designed by manual calculations. Drawing works together with design calculations should be redone for every designing work, and also be needed to make some corrections of them. In order to design the AHU more efficiently, an AHU program has been developed. The developed program on the Windows environment is operated by the Graphic User Interface(GUI) realized using the Visual Basic Interpreter. The program provides calculation sheet of coils, weights and pressures in a MS-Excel file format as well as design drawing of the AHU in a auto CAD file format idealized by AutoLISP. Those files of the commercial softwares make easier for a designer to transfer design results to the another company for bid via e-mail

Development of design program for air handling units

Energy Technology Data Exchange (ETDEWEB)

Ham, J.K.; Kim, J.H.; Kim, Y.K.; Kim, Y.I.; Kang, P.Y. [Hyundai Heavy Industries Co., Ltd. (Korea)

2000-11-01

An air handling unit(AHU) has been usually designed by manual calculations. Drawing works together with design calculations should be redone for every designing work, and also be needed to make some corrections of them. In order to design the AHU more efficiently, an AHU program has been developed. The developed program on the Windows environment is operated by the graphic user interface(GUI) realized using the Visual Basic Interpreter. The program provides calculation sheet of coils, weights and pressures in a MS-Excel file format as well as design drawing of the AHU in a Auto CAD file format idealized by AutoLISP. Those files of the commercial softwares make easier for a designer to transfer design results to the another company for bid via e-mail. (author). 5 refs., 9 figs., 3 tabs.

Designing Online Management Education Courses Using the Community of Inquiry Framework

Science.gov (United States)

Weyant, Lee E.

2013-01-01

Online learning has grown as a program delivery option for many colleges and programs of business. The Community of Inquiry (CoI) framework consisting of three interrelated elements--social presence, cognitive presence, and teaching presences--provides a model to guide business faculty in their online course design. The course design of an online…

Successful Bullying Prevention Programs: Influence of Research Design, Implementation Features, and Program Components

Directory of Open Access Journals (Sweden)

Bryanna Hahn Fox

2012-12-01

Full Text Available Bullying prevention programs have been shown to be generally effective in reducing bullying and victimization. However, the effects are relatively small in randomized experiments and greater in quasi-experimental and age-cohort designs. Programs that are more intensive and of longer duration (for both children and teachers are more effective, as are programs containing more components. Several program components are associated with large effect sizes, including parent training or meetings and teacher training. These results should inform the design and evaluation of anti-bullying programs in the future, and a system ofaccreditation of effective programs.

Programming languages for circuit design.

Science.gov (United States)

Pedersen, Michael; Yordanov, Boyan

2015-01-01

This chapter provides an overview of a programming language for Genetic Engineering of Cells (GEC). A GEC program specifies a genetic circuit at a high level of abstraction through constraints on otherwise unspecified DNA parts. The GEC compiler then selects parts which satisfy the constraints from a given parts database. GEC further provides more conventional programming language constructs for abstraction, e.g., through modularity. The GEC language and compiler is available through a Web tool which also provides functionality, e.g., for simulation of designed circuits.

Computer Aided Design System for Developing Musical Fountain Programs

Institute of Scientific and Technical Information of China (English)

刘丹; 张乃尧; 朱汉城

2003-01-01

A computer aided design system for developing musical fountain programs was developed with multiple functions such as intelligent design, 3-D animation, manual modification and synchronized motion to make the development process more efficient. The system first analyzed the music form and sentiment using many basic features of the music to select a basic fountain program. Then, this program is simulated with 3-D animation and modified manually to achieve the desired results. Finally, the program is transformed to a computer control program to control the musical fountain in time with the music. A prototype system for the musical fountain was also developed. It was tested with many styles of music and users were quite satisfied with its performance. By integrating various functions, the proposed computer aided design system for developing musical fountain programs greatly simplified the design of the musical fountain programs.

Energy options for residential buildings assessment

International Nuclear Information System (INIS)

Rezaie, Behnaz; Dincer, Ibrahim; Esmailzadeh, Ebrahim

2013-01-01

Highlights: ► Studying various building energy options. ► Assessing these options from various points. ► Comparing these options for better environment and sustainability. ► Proposing renewable energy options as potential solutions. - Abstract: The building sector, as one of the major energy consumers, demands most of the energy research to assess different energy options from various aspects. In this paper, two similar residential buildings, with either low or high energy consumption patterns, are chosen as case studies. For these case studies, three different renewable energy technology and three different hybrid systems are designed for a specified size. Then, the environmental impact indices, renewable energy indices, and the renewable exergy indices have been estimated for every energy options. Results obtained show that the hybrid systems (without considering the economics factors) are superior and having top indices. The importance of the energy consumption patterns in buildings are proven by the indices. By cutting the energy consumption to about 40% the environment index would increase by more than twice (2.1). Utilization of the non-fossil fuels is one part of the solution to environmental problems while energy conservation being the other. It has been shown that the re-design of the energy consumption model is less complex but more achievable for buildings.

Development of stripper options for FRIB

Energy Technology Data Exchange (ETDEWEB)

Marti, F.; Hershcovitch, A.; Momozaki, Y.; Nolen, J.; Reed, C.; Thieberger, P.

2010-09-12

The US Department of Energy Facility for Rare Isotope Beams (FRIB) at Michigan State University includes a heavy ion superconducting linac capable of accelerating all ions up to uranium with energies higher than 200 MeV/u and beam power up to 400 kW. To achieve these goals with present ion source performance it is necessary to accelerate simultaneously two charge states of uranium from the ion source in the first section of the linac. At an energy of approximately 16.5 MeV/u it is planned to strip the uranium beam to reduce the voltage needed in the rest of the linac to achieve the final energy. Up to five different charge states are planned to be accelerated simultaneously after the stripper. The design of the stripper is a challenging problem due to the high power deposited (approximately 0.7 kW) in the stripper media by the beam in a small spot. To assure success of the project we have established a research and development program that includes several options: carbon or diamond foils, liquid lithium films, gas strippers and plasma strippers. We present in this paper the status of the different options.

An exploration of the option space in student design projects for uncertainty and sensitivity analysis with performance simulation

NARCIS (Netherlands)

Struck, C.; Wilde, de P.J.C.J.; Hopfe, C.J.; Hensen, J.L.M.

2008-01-01

This paper describes research conducted to gather empirical evidence on extent, character and content of the option space in building design projects, from the perspective of a climate engineer using building performance simulation for concept evaluation. The goal is to support uncertainty analysis

Nuclear Fuel Cycle Options Catalog: FY16 Improvements and Additions

Energy Technology Data Exchange (ETDEWEB)

Price, Laura L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Barela, Amanda Crystal [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schetnan, Richard Reed [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Walkow, Walter M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-08-31

The United States Department of Energy, Office of Nuclear Energy, Fuel Cycle Technology Program sponsors nuclear fuel cycle research and development. As part of its Fuel Cycle Options campaign, the DOE has established the Nuclear Fuel Cycle Options Catalog. The catalog is intended for use by the Fuel Cycle Technologies Program in planning its research and development activities and disseminating information regarding nuclear energy to interested parties. The purpose of this report is to document the improvements and additions that have been made to the Nuclear Fuel Cycle Options Catalog in the 2016 fiscal year.

Nuclear Fuel Cycle Options Catalog FY15 Improvements and Additions.

Energy Technology Data Exchange (ETDEWEB)

Price, Laura L. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Barela, Amanda Crystal [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Schetnan, Richard Reed [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Walkow, Walter M. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

2015-11-01

The United States Department of Energy, Office of Nuclear Energy, Fuel Cycle Technology Program sponsors nuclear fuel cycle research and development. As part of its Fuel Cycle Options campaign, the DOE has established the Nuclear Fuel Cycle Options Catalog. The catalog is intended for use by the Fuel Cycle Technologies Program in planning its research and development activities and disseminating information regarding nuclear energy to interested parties. The purpose of this report is to document the improvements and additions that have been made to the Nuclear Fuel Cycle Options Catalog in the 2015 fiscal year.

NASA universities advanced space design program, focus on nuclear engineering

International Nuclear Information System (INIS)

Lyon, W.F. III; George, J.A.; Alred, J.W.; Peddicord, K.L.

1987-01-01

In January 1985, the National Aeronautics and Space Administration (NASA), in affiliation with the Universities Space Research Association (USRA), inaugurated the NASA Universities Advanced Space Design Program. The purpose of the program was to encourage participating universities to utilize design projects for the senior and graduate level design courses that would focus on topics relevant to the nation's space program. The activities and projects being carried out under the NASA Universities Advanced Space Design Program are excellent experiences for the participants. This program is a well-conceived, well-planned effort to achieve the maximum benefit out of not only the university design experience but also of the subsequent summer programs. The students in the university design classes have the opportunity to investigate dramatic and new concepts, which at the same time have a place in a program of national importance. This program could serve as a very useful model for the development of university interaction with other federal agencies

Life-cycle cost analysis of energy efficiency design options for residential furnaces and boilers

Energy Technology Data Exchange (ETDEWEB)

Lutz, J.; Lekov, A.; Chan, P.; Dunham Whitehead, C.; Meyers, S.; McMahon, J. [Lawrence Berkeley National Laboratory, Berkeley, CA (United States). Environmental Energy Technologies Div.

2006-03-01

In 2001, the US Department of Energy (DOE) initiated a rulemaking process to consider whether to amend the existing energy efficiency standards for furnaces and boilers. A key factor in DOE's consideration of new standards is the economic impacts on consumers of possible revisions to energy-efficiency standards. Determining cost-effectiveness requires an appropriate comparison of the additional first cost of energy efficiency design options with the savings in operating costs. DOE's preferred approach involves comparing the total life-cycle cost (LCC) of owning and operating a more efficient appliance with the LCC for a baseline design. This study describes the method used to conduct the LCC analysis and presents the estimated change in LCC associated with more energy-efficient equipment. The results indicate that efficiency improvement relative to the baseline design can reduce the LCC in each of the product classes considered. (author)

Options for rural electrification in Mexico

International Nuclear Information System (INIS)

Vera, J.G.

1992-01-01

This paper summarizes a study which examined 19 commercially available options for electrifying remote communities in Mexico. Characteristics of a typical community are defined and, using 7 of the technologies, power systems are designed capable of supporting this community. The performance of these systems is evaluated with respect to their ability to satisfy 11 technical design objectives, 5 socioeconomic objectives, and their impact on the environment. A photovoltaic- diesel generator hybrid system with wind generator option is recommended for the typical community

Space Civil Engineering option - A progress report

Science.gov (United States)

Criswell, Marvin E.; Sadeh, Willy Z.

1992-01-01

Space Civil Engineering is an emerging engineering discipline that focuses on extending and expanding Civil Engineering to the development, operation, and maintenance of infrastructures on celestial bodies. Space Civil Engineering is presently being developed as a new discipline within the Department of Civil Engineering at Colorado State University and with support of the NASA Space Grant College Program. Academic programs geared toward creating Space Civil Engineering Options at both undergraduate and graduate levels are being formulated. Basic ideas and concepts and the current status of the curriculum in the Space Civil Engineering Option primarily at the undergraduate level are presented.

Thermal test options

International Nuclear Information System (INIS)

Koski, J.A.; Keltner, N.R.; Sobolik, K.B.

1993-02-01

Shipping containers for radioactive materials must be qualified to meet a thermal accident environment specified in regulations, such at Title 10, Code of Federal Regulations, Part 71. Aimed primarily at the shipping container design, this report discusses the thermal testing options available for meeting the regulatory requirements, and states the advantages and disadvantages of each approach. The principal options considered are testing with radiant heat, furnaces, and open pool fires. The report also identifies some of the facilities available and current contacts. Finally, the report makes some recommendations on the appropriate use of these different testing methods

Re-Imagining Program Development and Re-Engineering Program Design.

Science.gov (United States)

Currie, Geoffrey M; Thomas, Catherine J

2018-05-03

Program development and review is a central part of institutional and industry quality assurance. Traditional approaches, while well established, present a number of barriers that could undermine process integrity and quality outcomes. Here a new approach to program development and design is explored with the goal of enhancing outcomes for students and institutions. Copyright © 2018 by the Society of Nuclear Medicine and Molecular Imaging, Inc.

Slide layout and integrated design (SLIDE) program

International Nuclear Information System (INIS)

Roberts, S.G.

1975-01-01

SLIDE is a FORTRAN IV program for producing 35 mm color slides on the Control Data CYBER-74. SLIDE interfaces with the graphics package, DISSPLA, on the CYBER-74. It was designed so that persons with no previous computer experience can easily and quickly generate their own textual 35 mm color slides for verbal presentations. SLIDE's features include seven different colors, five text sizes, ten tab positions, and two page sizes. As many slides as desired may be produced during any one run of the program. Each slide is designed to represent an 8 1 / 2 in. x 11 in. or an 11 in. x 8 1 / 2 in. page. The input data cards required to run the SLIDE program and the program output are described. Appendixes contain a sample program run showing input, output, and the resulting slides produced and a FORTRAN listing of the SLIDE program. (U.S.)

Design Options for Thermal Shutdown Circuitry with Hysteresis Width Independent on the Activation Temperature

Directory of Open Access Journals (Sweden)

PLESA, C.-S.

2017-02-01

Full Text Available This paper presents several design options for implementing a thermal shutdown circuit with hysteretic characteristic, which has two special features: a programmable activation temperature (the upper trip point of the characteristic and a hysteresis width largely insensitive to the actual value of the activation temperature and to variations of the supply voltage. A fairly straightforward architecture is employed, with the hysteresis implemented by a current source enabled by the output of the circuit. Four possible designs are considered for this current source: VBE/R, modified-VBE/R, Widlar and a peaking current source tailored for this circuit. First, a detailed analytical analysis of the circuit implemented with these current sources is performed; it indicates the one best suited for this application and provides key sizing equations. Next, the chosen current source is employed to design the thermal shutdown protection of an integrated Low-Dropout Voltage Regulator (LDO for automotive applications. Simulation results and measurements performed on the silicon implementation fully validate the design. Moreover, they compare favorably with the performance of similar circuits reported recently.

Repowering options for steam power plants

International Nuclear Information System (INIS)

Wen, H.; Gopalarathinam, R.

1992-01-01

Repowering an existing steam power plant with a gas turbine offers an attractive alternative to a new plant or life extension, especially for unit sizes smaller than 300 MWe. Gas turbine repowering improves thermal efficiency and substantially increases the plant output. Based on recent repowering studies and projects, this paper examines gas turbine repowering options for 100 MWe, 200 MWe and 300 MWe units originally designed for coal firing and currently firing either coal or natural gas. Also discussed is the option for a phased future conversion of the repowered unit to fire coal-derived gas, should there be a fluctuation in the price or availability of natural gas. A modular coal gasification plant designed to shorten the conversion time is presented. Repowering options, performance, costs, and availability impacts are discussed for selected cases

Nuclear Engine System Simulation (NESS). Volume 1: Program user's guide. Final Report

International Nuclear Information System (INIS)

Pelaccio, D.G.; Scheil, C.M.; Petrosky, L.J.

1993-03-01

A Nuclear Thermal Propulsion (NTP) engine system design analysis tool is required to support current and future Space Exploration Initiative (SEI) propulsion and vehicle design studies. Currently available NTP engine design models are those developed during the NERVA program in the 1960's and early 1970's and are highly unique to that design or are modifications of current liquid propulsion system design models. To date, NTP engine-based liquid design models lack integrated design of key NTP engine design features in the areas of reactor, shielding, multi-propellant capability, and multi-redundant pump feed fuel systems. Additionally, since the SEI effort is in the initial development stage, a robust, verified NTP analysis design tool could be of great use to the community. This effort developed an NTP engine system design analysis program (tool), known as the Nuclear Engine System Simulation (NESS) program, to support ongoing and future engine system and stage design study efforts. In this effort, Science Applications International Corporation's (SAIC) NTP version of the Expanded Liquid Engine Simulation (ELES) program was modified extensively to include Westinghouse Electric Corporation's near-term solid-core reactor design model. The ELES program has extensive capability to conduct preliminary system design analysis of liquid rocket systems and vehicles. The program is modular in nature and is versatile in terms of modeling state-of-the-art component and system options as discussed. The Westinghouse reactor design model, which was integrated in the NESS program, is based on the near-term solid-core ENABLER NTP reactor design concept. This program is now capable of accurately modeling (characterizing) a complete near-term solid-core NTP engine system in great detail, for a number of design options, in an efficient manner

Design Minimalism in Robotics Programming

Directory of Open Access Journals (Sweden)

Anthony Cowley

2008-11-01

Full Text Available With the increasing use of general robotic platforms in different application scenarios, modularity and reusability have become key issues in effective robotics programming. In this paper, we present a minimalist approach for designing robot software, in which very simple modules, with well designed interfaces and very little redundancy can be connected through a strongly typed framework to specify and execute different robotics tasks.

Design Minimalism in Robotics Programming

Directory of Open Access Journals (Sweden)

Anthony Cowley

2006-03-01

Full Text Available With the increasing use of general robotic platforms in different application scenarios, modularity and reusability have become key issues in effective robotics programming. In this paper, we present a minimalist approach for designing robot software, in which very simple modules, with well designed interfaces and very little redundancy can be connected through a strongly typed framework to specify and execute different robotics tasks.

Designing health promotion programs by watching the market.

Science.gov (United States)

Gelb, B D; Bryant, J M

1992-03-01

More health care providers and payors are beginning to see health promotion programs as a significant tool for attracting patients, reducing costs, or both. To help design programs that take into account the values and lifestyles of the target group, naturalistic observation can be useful. The authors illustrate the approach in a study of pipeline workers that provided input for the design of nutrition and smoking cessation programs.

FTR-option formulation and pricing

International Nuclear Information System (INIS)

Parmeshwaran, Vijay; Muthuraman, Kumar

2009-01-01

Recent changes in electricity markets have advocated the use of Local Marginal Prices (LMP) for congestion management and pricing. From the perspective of market participants, the LMPs pose a risk since they are not known before a transaction on the grid is made. Financial transmission rights (FTR) are instruments that help market participants hedge this risk and are issuable in two flavors - obligations and options. While pricing obligations are much easier, pricing FTR options pose a significant challenge. In this paper we develop a computational method for pricing FTR options. We also discuss the problem of designing financial instrument sets that assure revenue adequacy for the issuer. We point out the difficulty in assuring revenue adequacy when FTR options are present and propose a scheme for overcoming the difficulty. The proposed pricing method can be used to compute prices of options and obligations in the primary market or as a reliable pricing tool to compute option prices in the secondary market. Finally using a test network we present and discuss numerical results. (author)

Designing PV Incentive Programs to Promote System Performance: AReview of Current Practice

Energy Technology Data Exchange (ETDEWEB)

Barbose, Galen; Wiser, Ryan; Bolinger, Mark

2006-11-12

rather than the rated capacity of the modules or system, are often suggested as one possible strategy. Somewhat less recognized are the many other program design options also available, each with its particular advantages and disadvantages. To provide a point of reference for assessing the current state of the art, and to inform program design efforts going forward, we examine the approaches to encouraging PV system performance - including, but not limited to, PBIs - used by 32 prominent PV incentive programs in the U.S. (see Table 1).1 We focus specifically on programs that offer an explicit subsidy payment for customer-sited PV installations. PV support programs that offer other forms of financial support or that function primarily as a mechanism for purchasing renewable energy credits (RECs) through energy production-based payments are outside the scope of our review.2 The information presented herein is derived primarily from publicly available sources, including program websites and guidebooks, programs evaluations, and conference papers, as well as from a limited number of personal communications with program staff. The remainder of this report is organized as follows. The next section presents a simple conceptual framework for understanding the issues that affect PV system performance and provides an overview of the eight general strategies to encourage performance used among the programs reviewed in this report. The subsequent eight sections discuss in greater detail each of these program design strategies and describe how they have been implemented among the programs surveyed. Based on this review, we then offer a series of recommendations for how PV incentive programs can effectively promote PV system performance.

Lunar Cube Transfer Trajectory Options

Science.gov (United States)

Folta, David; Dichmann, Donald James; Clark, Pamela E.; Haapala, Amanda; Howell, Kathleen

2015-01-01

Numerous Earth-Moon trajectory and lunar orbit options are available for Cubesat missions. Given the limited Cubesat injection infrastructure, transfer trajectories are contingent upon the modification of an initial condition of the injected or deployed orbit. Additionally, these transfers can be restricted by the selection or designs of Cubesat subsystems such as propulsion or communication. Nonetheless, many trajectory options can b e considered which have a wide range of transfer duration, fuel requirements, and final destinations. Our investigation of potential trajectories highlights several options including deployment from low Earth orbit (LEO) geostationary transfer orbits (GTO) and higher energy direct lunar transfer and the use of longer duration Earth-Moon dynamical systems. For missions with an intended lunar orbit, much of the design process is spent optimizing a ballistic capture while other science locations such as Sun-Earth libration or heliocentric orbits may simply require a reduced Delta-V imparted at a convenient location along the trajectory.

Advanced nuclear plant design options to cope with external events

International Nuclear Information System (INIS)

2006-02-01

With the stagnation period of nuclear power apparently coming to an end, there is a renewed interest in many Member States in the development and application of nuclear power plants (NPPs) with advanced reactors. Decisions on the construction of several NPPs with evolutionary light water reactors have been made (e.g. EPR Finland for Finland and France) and more are under consideration. There is a noticeable progress in the development and demonstration of innovative high temperature gas cooled reactors, for example, in China, South Africa and Japan. The Generation IV International Forum has defined the International Near Term Deployment programme and, for a more distant perspective, six innovative nuclear energy systems have been selected and certain R and D started by several participating countries. National efforts on design and technology development for NPPs with advanced reactors, both evolutionary and innovative, are ongoing in many Member States. Advanced NPPs have an opportunity to be built at many sites around the world, with very broad siting conditions. There are special concerns that safety of these advanced reactors may be challenged by external events following new scenarios and failure modes, different from those well known for the currently operated reactors. Therefore, the engineering community identified the need to assess the proposed design configurations in relation to external scenarios at the earliest stages of the design development. It appears that an early design optimization in relation to external events is a necessary requirement to achieve safe and economical advanced nuclear power plants. Reflecting on these developments, the IAEA has planned the preparation of a report to define design options for protection from external event impacts in NPPs with evolutionary and innovative reactors. The objective of this publication is to present the state-of-the-art in design approaches for the protection of NPPs with evolutionary and innovative

Feed-pump hydraulic performance and design improvement, Phase I: research program design. Final report

Energy Technology Data Exchange (ETDEWEB)

Brown, W.H.; Gopalakrishnan, S.; Fehlau, R.; Thompson, W.E.; Wilson, D.G.

1982-03-01

As a result of prior EPRI-sponsored studies, it was concluded that a research program should be designed and implemented to provide an improved basis for the design, procurement, testing, and operation of large feed pumps with increased reliability and stability over the full range of operating conditions. This two-volume report contains a research plan which is based on a review of the present state of the art and which defines the necessary R and D program and estimates the benefits and costs of the program. The recommended research program consists of 30 interrelated tasks. It is designed to perform the needed research; to verify the results; to develop improved components; and to publish computer-aided design methods, pump specification guidelines, and a troubleshooting manual. Most of the technology proposed in the research plan is applicable to nuclear power plants as well as to fossil-fired plants. This volume discusses the design, performance and failures of feed pumps, and recommendations for research on pump dynamics, design, and specifications.

NRC Seismic Design Margins Program Plan

International Nuclear Information System (INIS)

Cummings, G.E.; Johnson, J.J.; Budnitz, R.J.

1985-08-01

Recent studies estimate that seismically induced core melt comes mainly from earthquakes in the peak ground acceleration range from 2 to 4 times the safe shutdown earthquake (SSE) acceleration used in plant design. However, from the licensing perspective of the US Nuclear Regulatory Commission, there is a continuing need for consideration of the inherent quantitative seismic margins because of, among other things, the changing perceptions of the seismic hazard. This paper discusses a Seismic Design Margins Program Plan, developed under the auspices of the US NRC, that provides the technical basis for assessing the significance of design margins in terms of overall plant safety. The Plan will also identify potential weaknesses that might have to be addressed, and will recommend technical methods for assessing margins at existing plants. For the purposes of this program, a general definition of seismic design margin is expressed in terms of how much larger that the design basis earthquake an earthquake must be to compromise plant safety. In this context, margin needs to be determined at the plant, system/function, structure, and component levels. 14 refs., 1 fig

Software tools to aid Pascal and Ada program design

Energy Technology Data Exchange (ETDEWEB)

Jankowitz, H.T.

1987-01-01

This thesis describes a software tool which analyses the style and structure of Pascal and Ada programs by ensuring that some minimum design requirements are fulfilled. The tool is used in much the same way as a compiler is used to teach students the syntax of a language, only in this case issues related to the design and structure of the program are of paramount importance. The tool operates by analyzing the design and structure of a syntactically correct program, automatically generating a report detailing changes that need to be made in order to ensure that the program is structurally sound. The author discusses how the model gradually evolved from a plagiarism detection system which extracted several measurable characteristics in a program to a model that analyzed the style of Pascal programs. In order to incorporate more-sophistical concepts like data abstraction, information hiding and data protection, this model was then extended to analyze the composition of Ada programs. The Ada model takes full advantage of facilities offered in the language and by using this tool the standard and quality of written programs is raised whilst the fundamental principles of program design are grasped through a process of self-tuition.

Application of RELAP/SCDAPSIM with integrated uncertainty options to research reactor systems thermal hydraulic analysis

International Nuclear Information System (INIS)

Allison, C.M.; Hohorst, J.K.; Perez, M.; Reventos, F.

2010-01-01

The RELAP/SCDAPSIM/MOD4.0 code, designed to predict the behavior of reactor systems during normal and accident conditions, is being developed as part of the international SCDAP Development and Training Program (SDTP). RELAP/SCDAPSIM/MOD4.0, which is the first version of RELAP5 completely rewritten to FORTRAN 90/95/2000 standards, uses publicly available RELAP5 and SCDAP models in combination with advanced programming and numerical techniques and other SDTP-member modeling/user options. One such member developed option is an integrated uncertainty analysis package being developed jointly by the Technical University of Catalonia (UPC) and Innovative Systems Software (ISS). This paper briefly summarizes the features of RELAP/SCDAPSIM/MOD4.0 and the integrated uncertainty analysis package, and then presents an example of how the integrated uncertainty package can be setup and used for a simple pipe flow problem. (author)

Programming biological operating systems: genome design, assembly and activation.

Science.gov (United States)

Gibson, Daniel G

2014-05-01

The DNA technologies developed over the past 20 years for reading and writing the genetic code converged when the first synthetic cell was created 4 years ago. An outcome of this work has been an extraordinary set of tools for synthesizing, assembling, engineering and transplanting whole bacterial genomes. Technical progress, options and applications for bacterial genome design, assembly and activation are discussed.

Perspective on long-range nuclear energy options

International Nuclear Information System (INIS)

Harms, W.O.

1977-01-01

The study group whose effort is presented here concluded that the United States urgently needs to have a breeder option available for possible deployment before the year 2000 primarily because of uncertainties in the availability of fossil fuels and uranium supplies. It was recommended that the U/Pu LMFBR program proceed as planned, including prompt construction of the CRBRP and its associated fuel cycle facilities. Alternative cycle studies should be pursued, but without significantly delaying the current program. There are technological choices which, in suitable political contexts, may somewhat reduce proliferation risks; of these, only those that employ breeders preserve the breeder option (and the nuclear option in the long term. These alternatives must be coupled with political agreements to have any significant effect on proliferation potential internationally. These same political agreements should suffice to control the U/Pu breeder cycle; there is only a difference in degree between the U/Pu and the denatured Th/U-233 cycles

Medical Student Interest in Flexible Residency Training Options.

Science.gov (United States)

Piotrowski, Madison; Stulberg, Debra; Egan, Mari

2018-05-01

Medical residents continue to experience high rates of burnout during residency training even after implementation of the 2003 Accreditation Council for Graduate Medical Education duty-hour restrictions. The purpose of this study is to determine medical student interest in flexible residency training options. Researchers developed an 11-question survey for second through fourth-year medical students. The populations surveyed included medical students who were: (1) attending the 2015 American Academy of Family Physicians National Conference, the 2015 Family Medicine Midwest Conference, and (2) enrolled at University of Chicago Pritzker School of Medicine, University of Illinois College of Medicine at Chicago, Drexel University College of Medicine, and Case Western Reserve University School of Medicine. The survey was completed by 789 medical students. Over half of medical students surveyed indicated that they would be interested in working part-time during some portion of their residency training (51%), and that access to part-time training options would increase their likelihood of applying to a particular residency program (52%). When given the option of three residency training schedules of varying lengths, 41% of male students and 60% of female students chose a 60-hour workweek, even when that meant extending the residency length by 33% and reducing their yearly salary to $39,000. There is considerable interest among medical students in access to part-time residency training options and reduced-hour residency programs. This level of interest indicates that offering flexible training options could be an effective recruitment tool for residency programs and could improve students' perception of their work-life balance during residency.

Decisions on Energy Demand Response Option Contracts in Smart Grids Based on Activity-Based Costing and Stochastic Programming

Directory of Open Access Journals (Sweden)

Alfred J. Hildreth

2013-01-01

Full Text Available Smart grids enable a two-way energy demand response capability through which a utility company offers its industrial customers various call options for energy load curtailment. If a customer has the capability to accurately determine whether to accept an offer or not, then in the case of accepting an offer, the customer can earn both an option premium to participate, and a strike price for load curtailments if requested. However, today most manufacturing companies lack the capability to make the correct contract decisions for given offers. This paper proposes a novel decision model based on activity-based costing (ABC and stochastic programming, developed to accurately evaluate the impact of load curtailments and determine as to whether or not to accept an energy load curtailment offer. The proposed model specifically targets state-transition flexible and Quality-of-Service (QoS flexible energy use activities to reduce the peak energy demand rate. An illustrative example with the proposed decision model under a call-option based energy demand response scenario is presented. As shown from the example results, the proposed decision model can be used with emerging smart grid opportunities to provide a competitive advantage to the manufacturing industry.

Assessing Window Replacement Options | Efficient Windows Collaborative

Science.gov (United States)

Foundry Foundry New Construction Windows Window Selection Tool Selection Process Design Guidance Installation Replacement Windows Window Selection Tool Assessing Options Selection Process Design Guidance Installation Understanding Windows Benefits Design Considerations Measuring Performance Performance Standards

Design of incentive programs for accelerating penetration of energy-efficient appliances

International Nuclear Information System (INIS)

Rue du Can de la, Stephane; Leventis, Greg; Phadke, Amol; Gopal, Anand

2014-01-01

Incentives are policy tools that sway purchase, retail stocking, and production decisions toward energy-efficient products. Incentives complement mandatory standards and labeling policies by accelerating market penetration of products that are more energy efficient than required by existing standards and by preparing the market for more stringent future mandatory requirements. Incentives can be directed at different points in the appliance's supply chain; one point may be more effective than another depending on the technology's maturity and market penetration. This paper seeks to inform future policy and program design by categorizing the main elements of incentive programs from around the world. We identify advantages and disadvantages of program designs through a qualitative overview of incentive programs worldwide. We find that financial incentive programs have greater impact when they target highly efficient technologies with a small market share, and that program designs depend on the market barriers addressed, the target equipment, and the local market context. No program design is inherently superior to another. The key to successful program design and implementation is a thorough understanding of the market and identification of the most important local obstacles to the penetration of energy-efficient technologies. - Highlights: • We researched incentive programs design and implementation worldwide. • This paper seeks to inform future policy and program design. • We identify design and identify advantages and disadvantages. • We find that incentive programs have greater impact when they target highly efficient products. • Program designs depend on the market barriers addressed and the local market context

Program computes single-point failures in critical system designs

Science.gov (United States)

Brown, W. R.

1967-01-01

Computer program analyzes the designs of critical systems that will either prove the design is free of single-point failures or detect each member of the population of single-point failures inherent in a system design. This program should find application in the checkout of redundant circuits and digital systems.

Influence of fuel costs on seawater desalination options

International Nuclear Information System (INIS)

Methnani, Mabrouk

2007-01-01

Reference estimates of seawater desalination costs for recent mega projects are all quoted in the range of US$0.50/m 3 . This however does not reflect the recent trends of escalating fossil fuel costs. In order to analyze the effect of these trends, a recently updated version of the IAEA Desalination Economic Evaluation Program, DEEP-3, has been used to compare fossil and nuclear seawater desalination options, under varied fuel cost and interest rate scenarios. Results presented for a gas combined-cycle and a modular high-temperature gas-cooled reactor design, show clear cost advantages for the latter, for both Multi-Effect Distillation (MED) and Reverse Osmosis (RO). Water production cost estimates for the Brayton cycle nuclear option are hardly affected by fuel costs, while combined cycle seawater desalination costs show an increase of more than 40% when fuel costs are doubled. For all cases run, the nuclear desalination costs are lower and if the current trend in fossil fuel prices continues as predicted by pessimist scenarios and the carbon tax carried by greenhouse emissions is enforced in the future, the cost advantage for nuclear desalination will be even more pronounced. Increasing the interest rate from 5 to 8% has a smaller effect than fuel cost variations. It translates into a water cost increase in the range of 10-20%, with the nuclear option being the more sensitive. (author)

An Overview of Turkish Healthcare System after Health Transformation Program: Main Successes, Performance Assessment, Further Challenges, and Policy Options

Directory of Open Access Journals (Sweden)

Kadir GÜRSOY

2015-02-01

Full Text Available Turkish healthcare system has been stated to show significant improvements regarding wider access to healthcare facilities, and the quality and efficiency through the introduction of Health Transformation Program launched in 2003. While the old system relied on differing provisions and financing and lacked behind many developed nations in terms of health outcomes, the new system achieved nearly universal coverage and many health outcomes enhanced significantly. Health expenditures rose to 5.4% of GDP in 2013 from 4.8% in 1998. Furthermore, Turkey provided both better financial protection for the poor against high health expenditures, and equity in access to health care across the population. However, Turkey still faces new challenges to catch other developed countries to have better health and further improve financial sustainability. To reach these targets, Turkey needs to further implement new policy options for reform such as combating informal economy, allocating more on health resources, designing incentive- based payment methods, adopting gate keeping system and referral chain, developing capacity to deploy health technology assessments in reimbursement decisions, and ensuring the hospital autonomy.

The Design Options and Provision File and the Role of Defence in Depth Within the Pre-Licensing of the MYRRHA Project

Energy Technology Data Exchange (ETDEWEB)

Fiorini, G. L.; Hakimi, N., E-mail: Gian-Luigi.fiorini@fanc.fgov.be [FANC (Belgium); Tombuyses, B.; Dams, C.; Wertelaers, A.; Schrauben, M.; Dresselaers, R. [Federal Agency for Nuclear Control (FANC), Bruxelles (Belgium)

2014-10-15

The Belgian Federal Agency for Nuclear Control (FANC) is engaged in a process of pre-licensing for the experimental reactor MYRRHA. The regulatory framework applicable for the implementation of the MYRRHA project and the expected safety, security and safeguards philosophy are described by FANC in a Strategic Note. This document presents a logical flow chart which defines the steps required to design a basic nuclear installation and ensure compliance with the requirements of nuclear safety, security and safeguards. Using this flow chart, the content of a set of volumes (Design Options and Provision File - DOPF) is defined; the DOPF will serve as a basis for the evaluation of the concept with the acceptability of the selected design options. Defence in depth (DiD) and its fundamental principles remain the foundation of the whole process. The paper summarizes the contents of the Strategic Note and the DOPF and focuses more specifically on aspects relating to changes in the concept of defence in depth and on practices for their integration in the process of design / assessment of the MYRRHA reactor. (author)

Program packages for dynamics systems analysis and design

International Nuclear Information System (INIS)

Athani, V.V.

1976-01-01

The development of computer program packages for dynamic system analysis and design are reported. The purpose of developing these program packages is to take the burden of writing computer programs off the mind of the system engineer and to enable him to concentrate on his main system analysis and design work. Towards this end, four standard computer program packages have been prepared : (1) TFANA - starting from system transfer function this program computes transient response, frequency response, root locus and stability by Routh Hurwitz criterion, (2) TFSYN - classical synthesis using algebraic method of Shipley, (3) MODANA - starting from state equations of the system this program computes solution of state equations, controllability, observability and stability, (4) OPTCON - This program obtains solutions of (i) linear regulator problem, (ii) servomechanism problems and (iii) problem of pole placement. The paper describes these program packages with the help of flowcharts and illustrates their use with the help of examples. (author)

An assessment of design control practices and design reconstitution programs in the nuclear power industry

International Nuclear Information System (INIS)

Imbro, E.V.

1991-02-01

The US Nuclear Regulatory Commission (NRC) and the utilities have identified shortcomings involving the maintenance of well-defined design bases and the availability of the necessary supporting design documentation. Many utilities have embarked on design-document reconstitution programs although there has been no clear consensus regarding what information should be included in design-bases documents, what is the minimum set of necessary design documents to support the design bases, or how missing or deficient design documentation should be handled. The NRC initiated a survey to ascertain the status of design control programs within the industry and the approaches to design-bases documentation used by some utilities. The survey scope included six utilities and one nuclear steam supply system vendor. Conclusions and observations resulting from the survey assessments are provided so that utilities and the NRC can consider actions to improve these programs. 12 refs

Proceedings of the Workshop on Program Options in Intermediate-Energy Physics. Keynote address: New directions in intermediate-energy nuclear physics

International Nuclear Information System (INIS)

Brown, G.E.

1980-05-01

This report presents the keynote address given by G.E. Brown at a LASL colloquium on August 21, 1979, for the Workshop on Program Options in Intermediate-Energy Physics. Professor Brown reviewed major topics of interest in intermediate-energy nuclear physics and suggested experimental approaches that might be most productive in the near future. 22 figures

An Agent-Based Approach for Evaluating Basic Design Options of Management Accounting Systems

Directory of Open Access Journals (Sweden)

Friederike Wall

2013-12-01

Full Text Available This paper investigates the effectiveness of reducing errors in management accounting systems with respect to organizational performance. In particular, different basic design options of management accounting systems of how to improve the information base by measurements of actual values are analyzed in different organizational contexts. The paper applies an agent-based simulation based on the idea of NK fitness landscapes. The results provide broad, but no universal support for conventional wisdom that lower inaccuracies of accounting information lead to more effective adaptation processes. Furthermore, results indicate that the effectiveness of improving the management accounting system subtly interferes with the complexity of the interactions within the organization and the coordination mode applied

Design study of a medical proton linac for neutron therapy

International Nuclear Information System (INIS)

Machida, S.; Raparia, D.

1988-01-01

This paper describes a design study which establishes the physical parameters of the low energy beam transport, radiofrequency quadrupole, and linac, using computer programs available at Fermilab. Beam dynamics studies verify that the desired beam parameters can be achieved. The machine described here meets the aforementioned requirements and can be built using existing technology. Also discussed are other technically feasible options which could be attractive to clinicians, though they would complicate the design of the machine and increase construction costs. One of these options would allow the machine to deliver 2.3 MeV protons to produce epithermal neutrons for treating brain tumors. A second option would provide 15 MeV protons for isotope production. 21 refs., 33 figs

LOFT fuel modules design, characterization, and fabrication program

International Nuclear Information System (INIS)

Russell, M.L.

1977-06-01

The loss-of-fluid test [LOFT) fuel modules have evolved from a comprehensive five-year design, characterization, and fabrication program which has resulted in the accomplishment of many technical activities of interest in pressurized water reactor fuel design development and safety research. Information is presented concerning: determination of fundamental high-temperature reactor material properties; design invention related to in-core instrumentation attachment; implementation of advanced and/or unique fuel bundle characterization techniques; implementation of improved fuel bundle fabrication techniques; and planning and execution of a multimillion dollar design, characterization, and fabrication program for pressurized water reactor fuel

Propulsive options for a manned Mars transportation system

International Nuclear Information System (INIS)

Braun, R.D.; Blersch, D.J.

1989-01-01

In this investigation, five potential manned Mars transportation systems are compared. These options include: (1) a single vehicle, chemically propelled (CHEM) option, (2) a single vehicle, nuclear thermal propulsion (NTP) option, (3) a single vehicle solar electric propulsion (SEP) option, (4) a single vehicle hybrid nuclear electric propulsion (NEP)/CHEM option, and (5) a dual vehicle option (NEP cargo spacecraft and CHEM manned vehicle). In addition to utilizing the initial vehicle weight in low-earth orbit as a measure of mission feasibility, this study addresses the major technological barriers each propulsive scenario must surpass. It is shown that instead of a single clearly superior propulsion system, each means of propulsion may be favored depending upon the specified program policy and the extent of the desired manned flight time. Furthermore, the effect which aerobraking and multiple transfer cycles have upon mission feasibility is considered. 18 refs

Westinghouse Owners Group Risk-Informed Regulation Efforts: Options 2 and 3

International Nuclear Information System (INIS)

Brown, Jason A.; Osterrieder, Robert A.; Lutz, Robert J.; Dingler, Maurice; Ward, Lewis A.

2002-01-01

The U.S. Nuclear Regulatory Commission (NRC) has initiated efforts to incorporate risk-informed methods to redefine the scope of the existing 10 CFR 50 regulations (Option 2) and to change the technical requirements of the regulations (Option 3). The overall objectives of these efforts are to enhance plant safety, provide a framework for risk-informed regulations, add flexibility to plant operations, and reduce regulatory burden. The Westinghouse Owners Group (WOG) has a variety of active programs in the risk-informed area, including a program in the Option 2 and Option 3 areas. These two programs will be summarized including the benefits and the technical approach. The purpose of Option 2 is to make changes to the overall scope of structures, systems and components (SSCs) covered by 10 CFR 50 requiring special treatment by formulating new risk-informed safety classification categories that are linked to current definitions of safety-related and important-to-safety. This initiative would permit possible changes to the current special treatment requirements based on risk insights. The Nuclear Energy Institute (NEI) has developed an Option 2 implementation guideline (NEI 00-04 Draft Revision B). The WOG has initiated a program to validate the NEI guideline and to provide an initial cost-benefit assessment of the revised categorization and treatment under Option 2 via trial application to two systems at both Surry Unit 1 and Wolf Creek. The WOG Option 2 program includes consideration of all of the components in the selected systems, regardless of whether or not they are modeled in the respective plant probabilistic risk assessment (PRA) studies. As a result, quantitative risk measures are not available for many of the components being considered. In this case, the WOG program will provide valuable input to the NEI guideline. Additionally, the WOG program extends the use of both of the dominant methodologies for risk-informed ISI (RI-ISI) to address repair and

Low-Carbon Warehousing: Examining Impacts of Building and Intra-Logistics Design Options on Energy Demand and the CO2 Emissions of Logistics Centers

Directory of Open Access Journals (Sweden)

Julia Freis

2016-05-01

Full Text Available Logistics centers contribute to CO2 emissions in the building and logistics sector and therefore share a responsibility to decarbonize not only the supply chain. Synergy effects in both building and intra-logistics should be considered as suitable levers to lower energy demand and related CO2 emissions. This research develops firs t with a systemic approach an integrated analytical model for energy calculation and reference building models for different types of logistics centers to provide basic knowledge and a methodological framework for planners and managers to aid in the selection of different intra-logistics and building design options for optimum energy efficiency. It then determines the energy demand in reference building models and performs parameter studies to examine interrelations and impacts of design options for intra-logistics, building technology, and building skin on energy demand. It combines these to optimized reference building models to show the extent to which energy and CO2 emission savings can be reached. The results show that it is possible to significantly lower CO2 emissions. However, there are clear differences between the different types of logistics centers and the impacts of different design options.

24 CFR 982.633 - Homeownership option: Continued assistance requirements; Family obligations.

Science.gov (United States)

2010-04-01

... CHOICE VOUCHER PROGRAM Special Housing Types Homeownership Option § 982.633 Homeownership option... payment of the mortgage debt; (B) Any sale or other transfer of any interest in the home; or (C) The...

Evaluation of design options for improving the energy efficiency of an environmentally safe domestic refrigerator-freezer

Energy Technology Data Exchange (ETDEWEB)

Vineyard, E.A.; Sand, J.R. [Oak Ridge National Lab., TN (United States); Bohman, R.H.

1995-03-01

In order to reduce greenhouse emissions from power plants and respond to regulatory actions arising from the National Appliance Energy Conservation Act (NAECA), several design options were investigated for improving the energy efficiency of a conventionally designed, domestic refrigerator-freezer. The options, such as improved cabinet insulation and high-efficiency compressor and fans, were incorporated into a prototype refrigerator-freezer cabinet and refrigeration system to produce a unit that is superior from an environmental viewpoint due to its lower energy consumption and the use of refrigerant HFC-134a as a replacement for CFC-12. Baseline energy performance of the original 1993 production refrigerator-freezer, along with cabinet heat load and compressor calorimeter test results, were extensively documented to provide a firm basis for experimentally measured energy savings. A detailed refrigerator system computer model was used to evaluate the energy savings for several design modifications that, collectively, could achieve a targeted energy consumption of 1.00 kWh/d for a 20 ft{sup 3} (570 l) top-mount, automatic-defrost, refrigerator-freezer. The energy consumption goal represents a 50% reduction in the 1993 NAECA standard for units of this size. Following the modeling simulation, laboratory prototypes were fabricated and tested to experimentally verify the analytical results and aid in improving the model in those areas where discrepancies occurred. While the 1.00 kWh/d goal was not achieved with the modifications, a substantial energy efficiency improvement of 22% (1.41 kWh/d) was demonstrated using near-term technologies. It is noted that each improvement exacts a penalty in terms of increased cost or system complexity/reliability. Further work on this project will analyze cost-effectiveness of the design changes and investigate alternative, more-elaborate, refrigeration system changes to further reduce energy consumption.

Design criteria for piping and nozzles program

International Nuclear Information System (INIS)

Moore, S.E.; Bryson, J.W.

1977-01-01

This report reviews the activities and accomplishments of the Design Criteria for Piping and Nozzles program being conducted by the Oak Ridge National Laboratory for the period July 1, 1975, to September 30, 1976. The objectives of the program are to conduct integrated experimental and analytical stress analysis studies of piping system components and isolated and closely-spaced pressure vessel nozzles in order to confirm and/or improve the adequacy of structural design criteria and analytical methods used to assure the safe design of nuclear power plants. Activities this year included the development of a finite-element program for analyzing two closely spaced nozzles in a cylindrical pressure vessel; a limited-parameter study of vessels with isolated nozzles, finite-element studies of piping elbows, a fatigue test of an out-of-round elbow, summary and evaluation of experimental studies on the elastic-response and fatigue failure of tees, parameter studies on the behavior of flanged joints, publication of fifteen topical reports and papers on various experimental and analytical studies; and the development and acceptance of a number of design rules changes to the ASME Code. 2 figures, 2 tables

Role of male partner involvement in ART retention and adherence in Malawi's Option B+ program.

Science.gov (United States)

Wesevich, Austin; Mtande, Tiwonge; Saidi, Friday; Cromwell, Elizabeth; Tweya, Hannock; Hosseinipour, Mina C; Hoffman, Irving; Miller, William C; Rosenberg, Nora E

2017-11-01

Malawi's Option B+ program provides all HIV-infected pregnant women free lifelong antiretroviral therapy (ART), but challenges remain regarding retention and ART adherence, potentially due to male partner barriers. We explored relationships between male partner involvement and Option B+ retention and adherence. In 2014, a randomized controlled trial in Malawi compared male recruitment strategies for couple HIV testing and counseling (cHTC) at an antenatal clinic. This secondary analysis was conducted among the entire cohort (N = 200) of women, irrespective of randomization status. We assessed whether cHTC attendance, early disclosure of HIV-positive status, and partner ART reminders were associated with retention and adherence at one month after starting treatment. Retention was defined as attending HIV clinic follow-up within one day of running out of pills. Adherence was defined as taking ≥95% of ARTs by pill count. We used binomial regression to calculate adjusted risk ratios (aRR) and 95% confidence intervals (CI). Median female age was 26 years. Most women (79%) were retained; of these, 68% were adherent. Receiving cHTC was associated with improved retention (aRR 1.33, 95% CI 1.12, 1.59). Receiving male partner ART reminders was weakly associated with retention (aRR 1.16, 95% CI 0.96, 1.39). Disclosure within one day was not associated with retention (aRR 1.08, 95% CI: 0.91, 1.28). Among those who were retained, these three behaviors were not associated with improved 95% adherence. CHTC could play an important role in improving Option B+ retention. Increasing cHTC participation and enhancing adherence-related messages within cHTC are important.

Green marketing in the Massachusetts electric company retail competition pilot program

Energy Technology Data Exchange (ETDEWEB)

Rothstein, S.M.; Fang, J.M.

1997-10-01

With electric industry restructuring initiatives being introduced on the state and federal levels, retail access pilot programs serve an important function for examining competitive market issues, as well as marketing strategies and customer reactions to different power supply options. The experience gained through these pilots provides important insights into future power market operations, including the market for green power. The Massachusetts Electric Company`s (MECo`s) Choice: New England pilot for residential and small-business customers was a voluntary program developed primarily to test the billing and metering logistics that distribution companies will need in the competitive market. The pilot also offered a preview of program implementation and marketing under customer choice. It was the first retail competition pilot to explicitly include green power options in program design. The MECo pilot`s energy suppliers were selected through the issuance of a request for proposals (RFP). Respondents were asked to submit bids in one or more of three energy supply categories-price, green, and other options. These options were developed by the pilot administrator through internal meetings, discussions with state officials and other stakeholders, and a review of information from other similar pilots. For the green option, the pilot administrator did not establish a green standard. Instead, suppliers were allowed to submit offers that promoted environmental stewardship. Customer response to the different green options are reported. The pilot results clearly demonstrate that, in a competitive situation, there is interest in a variety of energy supply options, including green options. 2 tabs.

Heuristic program to design Relational Databases

Directory of Open Access Journals (Sweden)

Manuel Pereira Rosa

2009-09-01

Full Text Available The great development of today’s world determines that the world level of information increases day after day, however, the time allowed to transmit this information in the classrooms has not changed. Thus, the rational work in this respect is more than necessary. Besides, if for the solution of a given type of problem we do not have a working algorism, we have, first to look for a correct solution, then the heuristic programs are of paramount importance to succeed in these aspects. Having into consideration that the design of the database is, essentially, a process of problem resolution, this article aims at proposing a heuristic program for the design of the relating database.

User-Centered Design of GPU-Based Shader Programs

DEFF Research Database (Denmark)

Kraus, Martin

2012-01-01

In the context of game engines with graphical user interfaces, shader programs for GPUs (graphics processing units) are an asset for game development that is often used by artists and game developers without knowledge of shader programming. Thus, it is important that non-programmers are enabled...... to explore and exploit the full potential of shader programs. To this end, we develop principles and guidelines for the design of usercentered graphical interfaces for shaders. With the help of several examples, we show how the requirements of a user-centered interface design influence the choice of widgets...

Evaluation of electromagnetic loads on various design options of the ITER diagnostic upper port plug during plasma disruptions

International Nuclear Information System (INIS)

Pak, Sunil; Ku, Duck Young; Oh, Dong-Keun; Jhang, Hogun; Kim, Duck-Hoi; Cheon, Mun-Seong; Seon, Chang Rae; Lee, Hyeon Gon; Pitcher, Spencer

2011-01-01

Electromagnetic (EM) loads due to eddy current and halo current during plasma disruptions are evaluated for the ITER diagnostic upper port plug. To reduce strong EM loads acting on the port plug fixed to the vacuum vessel like a cantilever beam, three design options have been considered: removal of the diagnostic first wall, slitting of the diagnostic shield module and recess of the port plug. The main focus of the present study is to examine the efficacy of these options in terms of EM loads on the upper port plug. It is found that making slits is more effective than removing the first wall. It is also shown that the upper port plug needs to be recessed to reduce the EM load induced by halo current.

New Production Reactors Program Plan

Energy Technology Data Exchange (ETDEWEB)

1990-12-01

Part I of this New Production Reactors (NPR) Program Plan: describes the policy basis of the NPR Program; describes the mission and objectives of the NPR Program; identifies the requirements that must be met in order to achieve the mission and objectives; and describes and assesses the technology and siting options that were considered, the Program's preferred strategy, and its rationale. The implementation strategy for the New Production Reactors Program has three functions: Linking the design, construction, operation, and maintenance of facilities to policies requirements, and the process for selecting options. The development of an implementation strategy ensures that activities and procedures are consistent with the rationale and analysis underlying the Program. Organization of the Program. The strategy establishes plans, organizational structure, procedures, a budget, and a schedule for carrying out the Program. By doing so, the strategy ensures the clear assignment of responsibility and accountability. Management and monitoring of the Program. Finally, the strategy provides a basis for monitoring the Program so that technological, cost, and scheduling issues can be addressed when they arise as the Program proceeds. Like the rest of the Program Plan, the Implementation Strategy is a living document and will be periodically revised to reflect both progress made in the Program and adjustments in plans and policies as they are made. 21 figs., 5 tabs.

New Production Reactors Program Plan

International Nuclear Information System (INIS)

1990-12-01

Part I of this New Production Reactors (NPR) Program Plan: describes the policy basis of the NPR Program; describes the mission and objectives of the NPR Program; identifies the requirements that must be met in order to achieve the mission and objectives; and describes and assesses the technology and siting options that were considered, the Program's preferred strategy, and its rationale. The implementation strategy for the New Production Reactors Program has three functions: Linking the design, construction, operation, and maintenance of facilities to policies requirements, and the process for selecting options. The development of an implementation strategy ensures that activities and procedures are consistent with the rationale and analysis underlying the Program. Organization of the Program. The strategy establishes plans, organizational structure, procedures, a budget, and a schedule for carrying out the Program. By doing so, the strategy ensures the clear assignment of responsibility and accountability. Management and monitoring of the Program. Finally, the strategy provides a basis for monitoring the Program so that technological, cost, and scheduling issues can be addressed when they arise as the Program proceeds. Like the rest of the Program Plan, the Implementation Strategy is a living document and will be periodically revised to reflect both progress made in the Program and adjustments in plans and policies as they are made. 21 figs., 5 tabs

Energy options

International Nuclear Information System (INIS)

Hampton, Michael

1999-01-01

This chapter focuses on energy options as a means of managing exposure to energy prices. An intuitive approach to energy options is presented, and traditional definitions of call and put options are given. The relationship between options and swaps, option value and option exercises, commodity options, and option pricing are described. An end-user's guide to energy option strategy is outlined, and straight options, collars, participating swaps and collars, bull and bear spreads, and swaption are examined. Panels explaining the defining of basis risk, and discussing option pricing and the Greeks, delta hedging, managing oil options using the Black-Scholes model, caps, floors and collars, and guidelines on hedging versus speculation with options are included in the paper

40 CFR 158.510 - Tiered testing options for nonfood pesticides.

Science.gov (United States)

2010-07-01

... pesticides. 158.510 Section 158.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Toxicology § 158.510 Tiered testing options for nonfood pesticides. For nonfood use pesticides only, applicants have two options for generating and submitting...

ASDA - Advanced Suit Design Analyzer computer program

Science.gov (United States)

Bue, Grant C.; Conger, Bruce C.; Iovine, John V.; Chang, Chi-Min

1992-01-01

An ASDA model developed to evaluate the heat and mass transfer characteristics of advanced pressurized suit design concepts for low pressure or vacuum planetary applications is presented. The model is based on a generalized 3-layer suit that uses the Systems Integrated Numerical Differencing Analyzer '85 in conjunction with a 41-node FORTRAN routine. The latter simulates the transient heat transfer and respiratory processes of a human body in a suited environment. The user options for the suit encompass a liquid cooled garment, a removable jacket, a CO2/H2O permeable layer, and a phase change layer.

The Bonneville Power Administration new energy-efficient homes programs: Final environmental impact statement: Volume 1, Assessing indoor air quality options

International Nuclear Information System (INIS)

1988-03-01

BPA has underway marketing and incentive programs to encourage the construction of new energy-efficient homes that comply with Model Conservation Standards (MCS) developed by the Northwest Power Planning Council. These homes are designed to have lower infiltration rates than current building practices provide, which is likely to contribute to increased levels of indoor air pollutants, and may adversely affect the health of occupants. BPA's current and past new homes programs maintained ventilation rates comparable to those found in current practice homes by requiring balanced mechanical ventilation. BPA now proposes to give builders and consumers more flexibility by increasing the options for protecting indoor air quality in its new homes programs. This proposal is the impetus for this Environmental Impact Statement (EIS), which was prepared for BPA by Pacific Northwest Laboratory. BPS is preparing this EIS to assess whether other techniques maintain indoor air quality comparable to that found in homes built using current practices. Although many pollutants are potentially of great concern, our analysis concentrates on radon and formaldehyde. It is based on measured concentrations of these pollutants and measured ventilation rates in current practice. Ventilation was measured using fan pressurization tests, which measure only air leakage, and perfluorocarbon tracer gas (PFT) tests, which account for ventilation from mechanical devices and occupant behavior in addition to air leakage. These tests yielded two different estimates. We used these data to estimate pollutant concentrations and lifetime cancer rates under three alternative actions. Under all of the alternatives, radon had a much greater effect than formaldehyde. 102 refs

Program options to explore ocean worlds

Science.gov (United States)

Sherwood, B.; Lunine, J.; Sotin, C.; Cwik, T.; Naderi, F.

2018-02-01

Including Earth, roughly a dozen water ocean worlds exist in the solar system: the relict worlds Ceres and Mars, vast oceans inside most of the large Jovian and Saturnian icy moons, and Kuiper Belt Objects like Triton, Charon, and Pluto whose geologies are dominated by water and ammonia. Key pieces of the ocean-world science puzzle - which when completed may reveal whether life is widespread in the cosmos, why it exists where it does, and how it originates - are distributed among them. The eventual exploration of all these worlds will yield humanity's total tangible knowledge about life in the universe, essentially forever. Thus, their exploration has existential significance for humanity's self-regard, and indeed perhaps of our place in the natural scheme. The matter of planning how to pursue such a difficult and unprecedented exploration opportunity is therefore historic. The technical challenges are formidable, far harder than at Mars: missions to the Jovian and Saturnian ocean worlds are severely power-limited; trip times can be as much as a half decade and decade, respectively. And the science targets are global-scale oceans beneath kilometers of cryogenic ice. Reaching and exploring them would be a multi-generational undertaking, so again it is essential to plan and prepare. Today, we lack the instrumentation, subsystems, and remote operational-intelligence technologies needed to build and use exploration avatars as good as what we can envision needing. Each ocean world holds a piece of the puzzle, but the three priority targets are Europa at Jupiter, and Enceladus and Titan at Saturn. As with the systematic exploration of Mars, exploring these diverse worlds poses a complex technical and programmatic challenge - a strategic challenge - that needs to be designed and managed if each generation is to see its work bear fruit, and if the space science community is to make most effective use of the public money devoted to the quest. Strategic programs benefit from

Short educational programs in optical design and engineering

Science.gov (United States)

Voznesenskaya, Anna; Romanova, Galina; Bakholdin, Alexey; Tolstoba, Nadezhda; Ezhova, Kseniia

2016-09-01

Globalization and diversification of education in optical engineering causes a number of new phenomena in students' learning paths. Many students have an interest to get some courses in other universities, to study in international environment, to broaden not only professional skills but social links and see the sights as well etc. Participation in short educational programs (e.g. summer / winter schools, camps etc.) allows students from different universities to learn specific issues in their or in some neighbor field and also earn some ECTS for the transcript of records. ITMO University provides a variety of short educational programs in optical design and engineering oriented for different background level, such are: Introduction into optical engineering, Introduction into applied and computer optics, Optical system design, Image modeling and processing, Design of optical devices and components. Depending on students' educational background these programs are revised and adopted each time. Usually the short educational programs last 4 weeks and provide 4 ECTS. The short programs utilize a set of out-of date educational technologies like problem-based learning, case-study and distance-learning and evaluation. Practically, these technologies provide flexibility of the educational process and intensive growth of the learning outcomes. Students are satisfied with these programs very much. In their feedbacks they point a high level of practical significance, experienced teaching staff, scholarship program, excellent educational environment, as well as interesting social program and organizational support.

Design and Development of a Nonverbal Program

Science.gov (United States)

Thiagarajan, S.

1973-01-01

Problems were encountered in designing an illustrated program on contraceptive techniques for India's rural population where illiteracy is high and hundreds of different languages are spoken. Field trials of a picture program indicated the ability to "read" a picture is an acquired skill. (Author)

Dopamine Modulates Option Generation for Behavior.

Science.gov (United States)

Ang, Yuen-Siang; Manohar, Sanjay; Plant, Olivia; Kienast, Annika; Le Heron, Campbell; Muhammed, Kinan; Hu, Michele; Husain, Masud

2018-05-21

Animals make innumerable decisions every day, each of which involves evaluating potential options for action. But how are options generated? Although much is now known about decision making when a fixed set of potential options is provided, surprisingly little progress has been made on self-generated options. Some researchers have proposed that such abilities might be modulated by dopamine. Here, we used a new measure of option generation that is quantitative, objective, and culture fair to investigate how humans generate different behavioral options. Participants were asked to draw as many different paths (options) as they could between two points within a fixed time. Healthy individuals (n = 96) exhibited a trade-off between uniqueness (how individually different their options were) and fluency (number of options), generating either many similar or few unique options. To assess influence of dopamine, we first examined patients with Parkinson's disease (n = 35) ON and OFF their dopaminergic medication and compared them to elderly healthy controls (n = 34). Then we conducted a double-blind, placebo-controlled crossover study of the D2 agonist cabergoline in healthy older people (n = 29). Across both studies, dopamine increased fluency but diminished overall uniqueness of options generated, due to the effect of fluency trading off with uniqueness. Crucially, however, when this trade-off was corrected for, dopamine was found to increase uniqueness for any given fluency. Three carefully designed control studies showed that performance on our option-generation task was not related to executing movements, planning actions, or selecting between generated options. These findings show that dopamine plays an important role in modulating option generation. Copyright © 2018 The Author(s). Published by Elsevier Ltd.. All rights reserved.

Reliability-based econometrics of aerospace structural systems: Design criteria and test options. Ph.D. Thesis - Georgia Inst. of Tech.

Science.gov (United States)

Thomas, J. M.; Hanagud, S.

1974-01-01

The design criteria and test options for aerospace structural reliability were investigated. A decision methodology was developed for selecting a combination of structural tests and structural design factors. The decision method involves the use of Bayesian statistics and statistical decision theory. Procedures are discussed for obtaining and updating data-based probabilistic strength distributions for aerospace structures when test information is available and for obtaining subjective distributions when data are not available. The techniques used in developing the distributions are explained.

International Space Station (ISS) External Thermal Control System (ETCS) Loop A Pump Module (PM) Jettison Options Assessment

Science.gov (United States)

Murri, Daniel G.; Dwyer Cianciolo, Alicia; Shidner, Jeremy D.; Powell, Richard W.

2014-01-01

On December 11, 2013, the International Space Station (ISS) experienced a failure of the External Thermal Control System (ETCS) Loop A Pump Module (PM). To minimize the number of extravehicular activities (EVA) required to replace the PM, jettisoning the faulty pump was evaluated. The objective of this study was to independently evaluate the jettison options considered by the ISS Trajectory Operations Officer (TOPO) and to provide recommendations for safe jettison of the ETCS Loop A PM. The simulation selected to evaluate the TOPO options was the NASA Engineering and Safety Center's (NESC) version of Program to Optimize Simulated Trajectories II (POST2) developed to support another NESC assessment. The objective of the jettison analysis was twofold: (1) to independently verify TOPO posigrade and retrograde jettison results, and (2) to determine jettison guidelines based on additional sensitivity, trade study, and Monte Carlo (MC) analysis that would prevent PM recontact. Recontact in this study designates a propagated PM trajectory that comes within 500 m of the ISS propagated trajectory. An additional simulation using Systems Tool Kit (STK) was run for independent verification of the POST2 simulation results. Ultimately, the ISS Program removed the PM jettison option from consideration. However, prior to the Program decision, the retrograde jettison option remained part of the EVA contingency plan. The jettison analysis presented showed that, in addition to separation velocity/direction and the atmosphere conditions, the key variables in determining the time to recontact the ISS is highly dependent on the ballistic number (BN) difference between the object being jettisoned and the ISS.

Spent fuel storage - dry storage options and issues

International Nuclear Information System (INIS)

Akins, M.J.

2007-01-01

The increase in the number of nuclear energy power generation facilities will require the ability to store the spent nuclear fuel for a long period until the host countries develop reprocessing or disposal options. Plants have storage pools which are closely associated with the operating units. These are excellent for short term storage, but require active maintenance and operations support which are not desirable for the long term. Over the past 25 years, dry storage options have been developed and implemented throughout the world. In recent years, protection against terrorist attack has become an increasing source of design objectives for these facilities, as well as the main nuclear plant. This paper explores the current design options of dry storage cask systems and examines some of the current design issues for above ground , in-ground, or below-ground storage of spent fuel in dry casks. (author)

Mixed Waste Management Options: 1995 Update. National Low-Level Waste Management Program

Energy Technology Data Exchange (ETDEWEB)

Kirner, N.; Kelly, J.; Faison, G.; Johnson, D. [Foster Wheeler Environmental Corp. (United States)

1995-05-01

In the original mixed Waste Management Options (DOE/LLW-134) issued in December 1991, the question was posed, ``Can mixed waste be managed out of existence?`` That study found that most, but not all, of the Nation`s mixed waste can theoretically be managed out of existence. Four years later, the Nation is still faced with a lack of disposal options for commercially generated mixed waste. However, since publication of the original Mixed Waste Management Options report in 1991, limited disposal capacity and new technologies to treat mixed waste have become available. A more detailed estimate of the Nation`s mixed waste also became available when the US Environmental Protection Agency (EPA) and the US Nuclear Regulatory Commission (NRC) published their comprehensive assessment, titled National Profile on Commercially Generated Low-Level Radioactive Mixed Waste (National Profile). These advancements in our knowledge about mixed waste inventories and generation, coupled with greater treatment and disposal options, lead to a more applied question posed for this updated report: ``Which mixed waste has no treatment option?`` Beyond estimating the volume of mixed waste requiring jointly regulated disposal, this report also provides a general background on the Atomic Energy Act (AEA) and the Resource Conservation and Recovery Act (RCRA). It also presents a methodical approach for generators to use when deciding how to manage their mixed waste. The volume of mixed waste that may require land disposal in a jointly regulated facility each year was estimated through the application of this methodology.

Mixed Waste Management Options: 1995 Update. National Low-Level Waste Management Program

International Nuclear Information System (INIS)

Kirner, N.; Kelly, J.; Faison, G.; Johnson, D.

1995-05-01

In the original mixed Waste Management Options (DOE/LLW-134) issued in December 1991, the question was posed, ''Can mixed waste be managed out of existence?'' That study found that most, but not all, of the Nation's mixed waste can theoretically be managed out of existence. Four years later, the Nation is still faced with a lack of disposal options for commercially generated mixed waste. However, since publication of the original Mixed Waste Management Options report in 1991, limited disposal capacity and new technologies to treat mixed waste have become available. A more detailed estimate of the Nation's mixed waste also became available when the US Environmental Protection Agency (EPA) and the US Nuclear Regulatory Commission (NRC) published their comprehensive assessment, titled National Profile on Commercially Generated Low-Level Radioactive Mixed Waste (National Profile). These advancements in our knowledge about mixed waste inventories and generation, coupled with greater treatment and disposal options, lead to a more applied question posed for this updated report: ''Which mixed waste has no treatment option?'' Beyond estimating the volume of mixed waste requiring jointly regulated disposal, this report also provides a general background on the Atomic Energy Act (AEA) and the Resource Conservation and Recovery Act (RCRA). It also presents a methodical approach for generators to use when deciding how to manage their mixed waste. The volume of mixed waste that may require land disposal in a jointly regulated facility each year was estimated through the application of this methodology

Generative design visualize, program, and create with processing

CERN Document Server

Bohnacker, Hartmut; Laub, Julia; Lazzeroni, Claudius

2012-01-01

Generative design is a revolutionary new method of creating artwork, models, and animations from sets of rules, or algorithms. By using accessible programming languages such as Processing, artists and designers are producing extravagant, crystalline structures that can form the basis of anything from patterned textiles and typography to lighting, scientific diagrams, sculptures, films, and even fantastical buildings. Opening with a gallery of thirty-five illustrated case studies, Generative Design takes users through specific, practical instructions on how to create their own visual experiments by combining simple-to-use programming codes with basic design principles. A detailed handbook of advanced strategies provides visual artists with all the tools to achieve proficiency. Both a how-to manual and a showcase for recent work in this exciting new field, Generative Design is the definitive study and reference book that designers have been waiting for.

Core design options for high conversion BWRs operating in Th–233U fuel cycle

International Nuclear Information System (INIS)

Shaposhnik, Y.; Shwageraus, E.; Elias, E.

2013-01-01

Highlights: • BWR core operating in a closed self-sustainable Th– 233 U fuel cycle. • Seed blanket optimization that includes assembly size array and axial dimensions. • Fully coupled MC with fuel depletion and thermo-hydraulic feedback modules. • Thermal-hydraulic analysis includes MCPR observation. -- Abstract: Several options of fuel assembly design are investigated for a BWR core operating in a closed self-sustainable Th– 233 U fuel cycle. The designs rely on an axially heterogeneous fuel assembly structure consisting of a single axial fissile zone “sandwiched” between two fertile blanket zones, in order to improve fertile to fissile conversion ratio. The main objective of the study was to identify the most promising assembly design parameters, dimensions of fissile and fertile zones, for achieving net breeding of 233 U. The design challenge, in this respect, is that the fuel breeding potential is at odds with axial power peaking and the core minimum critical power ratio (CPR), hence limiting the maximum achievable core power rating. Calculations were performed with the BGCore system, which consists of the MCNP code coupled with fuel depletion and thermo-hydraulic feedback modules. A single 3-dimensional fuel assembly having reflective radial boundaries was modeled applying simplified restrictions on the maximum centerline fuel temperature and the CPR. It was found that axially heterogeneous fuel assembly design with a single fissile zone can potentially achieve net breeding, while matching conventional BWR core power rating under certain restrictions to the core loading pattern design

Handling and Emplacement Options for Deep Borehole Disposal Conceptual Design.

Energy Technology Data Exchange (ETDEWEB)

Cochran, John R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hardin, Ernest [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-07-01

This report presents conceptual design information for a system to handle and emplace packages containing radioactive waste, in boreholes 16,400 ft deep or possibly deeper. Its intended use is for a design selection study that compares the costs and risks associated with two emplacement methods: drill-string and wireline emplacement. The deep borehole disposal (DBD) concept calls for siting a borehole (or array of boreholes) that penetrate crystalline basement rock to a depth below surface of about 16,400 ft (5 km). Waste packages would be emplaced in the lower 6,560 ft (2 km) of the borehole, with sealing of appropriate portions of the upper 9,840 ft (3 km). A deep borehole field test (DBFT) is planned to test and refine the DBD concept. The DBFT is a scientific and engineering experiment, conducted at full-scale, in-situ, without radioactive waste. Waste handling operations are conceptualized to begin with the onsite receipt of a purpose-built Type B shipping cask, that contains a waste package. Emplacement operations begin when the cask is upended over the borehole, locked to a receiving flange or collar. The scope of emplacement includes activities to lower waste packages to total depth, and to retrieve them back to the surface when necessary for any reason. This report describes three concepts for the handling and emplacement of the waste packages: 1) a concept proposed by Woodward-Clyde Consultants in 1983; 2) an updated version of the 1983 concept developed for the DBFT; and 3) a new concept in which individual waste packages would be lowered to depth using a wireline. The systems described here could be adapted to different waste forms, but for design of waste packaging, handling, and emplacement systems the reference waste forms are DOE-owned high- level waste including Cs/Sr capsules and bulk granular HLW from fuel processing. Handling and Emplacement Options for Deep Borehole Disposal Conceptual Design July 23, 2015 iv ACKNOWLEDGEMENTS This report has

The bicalutamide Early Prostate Cancer Program. Demography

DEFF Research Database (Denmark)

See, W A.; McLeod, D; Iversen, P

2001-01-01

BACKGROUND: The optimal treatment for early prostate cancer has yet to be established. A well-tolerated hormonal therapy such as bicalutamide could be a useful treatment option in this setting, either as adjuvant or immediate therapy. A major collaborative clinical trials program was set up...... to investigate bicalutamide as a treatment option for local prostate cancer (localized or locally advanced disease). METHODS: The bicalutamide Early Prostate Cancer program comprises three randomized, double-blind, placebo-controlled trials of similar design that are being conducted in distinct geographical...... areas (North America; Australia, Europe, Israel, South Africa and Mexico; and Scandinavia). Men with T1b-4N0-1M0 (TNM 1997) prostate cancer have been randomized on a 1:1 basis to receive bicalutamide 150 mg daily or placebo. Recruitment to the program closed in July 1998, and follow-up is ongoing. Study...

Mars Earth Return Vehicle (MERV) Propulsion Options

Science.gov (United States)

Oleson, Steven R.; McGuire, Melissa L.; Burke, Laura; Fincannon, James; Warner, Joe; Williams, Glenn; Parkey, Thomas; Colozza, Tony; Fittje, Jim; Martini, Mike;

Options in Education: Program No. 88. Sex and Sexism in Education, Part II. Transcripts of a Weekly Series Broadcast by Member Stations of National Public Radio.

Science.gov (United States)

National Public Radio, Washington, DC.

This booklet is a transcription of a program from the radio series, "Options in Education." It is part 2 of a two-part series dealing with sexism in education. It deals with sex discrimination in various aspects of public education, including textbooks, teacher promotion, sports programs and children's literature. There is also a…

48 CFR 552.217-71 - Notice Regarding Option(s).

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Notice Regarding Option(s... Notice Regarding Option(s). As prescribed in 517.208(b), insert the following provision: Notice Regarding Option(s) (NOV 1992) The General Services Administration (GSA) has included an option to [Insert...

Improving Childcare Options to Create Better Economic ...

International Development Research Centre (IDRC) Digital Library (Canada)

Historically, women have relied on family, particularly grandmothers and ... how the lack of affordable childcare options can undermine women's ability to ... supported under the Growth and Economic Opportunities for Women (GrOW) program.

Fusion reactor design and technology program in China

International Nuclear Information System (INIS)

Huang, J.H.

1994-01-01

A fusion-fission hybrid reactor program was launched in 1987. The purpose of development of the hybrid reactor is twofold: to solve the problem of nuclear fuel supply for an expected large-scale development of fission reactor plants, and to maintain the momentum of fusion research. The program is described and the activities and progress of the program are presented. Two conceptual designs of an engineering test reactor with tokamak configuration were developed at the Southwestern Institute of Physics and the Institute of Plasma Physics. The results are a tokamak engineering test breeder (TETB) series design and a fusion-fission hybrid reactor design (SSEHR), characterized by a liquid-Li self-cooled blanket and an He-cooled solid tritium breeder blanket respectively. In parallel with the design studies, relevant technological experiments on a small or medium scale have been supported by this program. These include LHCD, ICRH and pellet injection in the area of plasma engineering; neutronics integral experiments with U, Pu, Fe and Be; various irradiation tests of austenitic and ferritic steels, magnetohydrodynamic (MHD) pressure drop experiments using a liquid metal loop; research into permeation barriers for tritium and hydrogen isotopes; solid tritium breeder tests using an in-situ loop in a fission reactor. All these experiments have proceeded successfully. The second step of this program is now starting. It seems reasonable that most of the research carried out in the first step will continue. ((orig.))

Reasons for the nuclear power option

International Nuclear Information System (INIS)

Rotaru, I.; Glodeanu, F.; Mauna, T.

1994-01-01

Technical, economical and social reasons, strongly supporting the nuclear power option are reviewed. The history of Romanian nuclear power program is outlined with a particular focus on the Cernavoda Nuclear Power Plant project. Finally the prospective of nuclear power in Romania are assessed

Computational Materials Program for Alloy Design

Science.gov (United States)

Bozzolo, Guillermo

2005-01-01

The research program sponsored by this grant, "Computational Materials Program for Alloy Design", covers a period of time of enormous change in the emerging field of computational materials science. The computational materials program started with the development of the BFS method for alloys, a quantum approximate method for atomistic analysis of alloys specifically tailored to effectively deal with the current challenges in the area of atomistic modeling and to support modern experimental programs. During the grant period, the program benefited from steady growth which, as detailed below, far exceeds its original set of goals and objectives. Not surprisingly, by the end of this grant, the methodology and the computational materials program became an established force in the materials communitiy, with substantial impact in several areas. Major achievements during the duration of the grant include the completion of a Level 1 Milestone for the HITEMP program at NASA Glenn, consisting of the planning, development and organization of an international conference held at the Ohio Aerospace Institute in August of 2002, finalizing a period of rapid insertion of the methodology in the research community worlwide. The conference, attended by citizens of 17 countries representing various fields of the research community, resulted in a special issue of the leading journal in the area of applied surface science. Another element of the Level 1 Milestone was the presentation of the first version of the Alloy Design Workbench software package, currently known as "adwTools". This software package constitutes the first PC-based piece of software for atomistic simulations for both solid alloys and surfaces in the market.Dissemination of results and insertion in the materials community worldwide was a primary focus during this period. As a result, the P.I. was responsible for presenting 37 contributed talks, 19 invited talks, and publishing 71 articles in peer-reviewed journals, as

Asteroid Redirect Robotic Mission: Robotic Boulder Capture Option Overview

Science.gov (United States)

Mazanek, Daniel D.; Merrill, Raymond G.; Belbin, Scott P.; Reeves, David M.; Earle, Kevin D.; Naasz, Bo J.; Abell, Paul A.

2014-01-01

The National Aeronautics and Space Administration (NASA) is currently studying an option for the Asteroid Redirect Robotic Mission (ARRM) that would capture a multi-ton boulder (typically 2-4 meters in size) from the surface of a large (is approximately 100+ meter) Near-Earth Asteroid (NEA) and return it to cislunar space for subsequent human and robotic exploration. This alternative mission approach, designated the Robotic Boulder Capture Option (Option B), has been investigated to determine the mission feasibility and identify potential differences from the initial ARRM concept of capturing an entire small NEA (4-10 meters in size), which has been designated the Small Asteroid Capture Option (Option A). Compared to the initial ARRM concept, Option B allows for centimeter-level characterization over an entire large NEA, the certainty of target NEA composition type, the ability to select the boulder that is captured, numerous opportunities for mission enhancements to support science objectives, additional experience operating at a low-gravity planetary body including extended surface contact, and the ability to demonstrate future planetary defense strategies on a hazardous-size NEA. Option B can leverage precursor missions and existing Agency capabilities to help ensure mission success by targeting wellcharacterized asteroids and can accommodate uncertain programmatic schedules by tailoring the return mass.

Waste package emplacement borehole option study

International Nuclear Information System (INIS)

Streeter, W.S.

1992-03-01

This study evaluates the cost and thermal effects of various waste package emplacement configurations that differ in emplacement orientation, number of containers per borehole, and standoff distance at the potential Yucca Mountain nuclear waste repository. In this study, eight additional alternatives to the vertical and horizontal orientation options presented in the Site Characterization Plan Conceptual Design Report are considered. Typical panel layout configurations based on thermal analysis of the waste and cost estimates for design and construction, operations, and closure and decommissioning were made for each emplacement option. For the thermal analysis average waste 10 years out of reactor and the SIM code were used to determine whether the various configurations temperatures would exceed the design criteria for temperature. This study does not make a recommendation for emplacement configuration, but does provide information for comparison of alternatives

24 CFR 982.632 - Homeownership option: Financing purchase of home; affordability of purchase.

Science.gov (United States)

2010-04-01

... CHOICE VOUCHER PROGRAM Special Housing Types Homeownership Option § 982.632 Homeownership option... payment mortgages, establishment of a minimum homeowner equity requirement from personal resources, or...

A Decision Support Framework for Feasibility Analysis of International Space Station (ISS) Research Capability Enhancing Options

Science.gov (United States)

Ortiz, James N.; Scott,Kelly; Smith, Harold

2004-01-01

The assembly and operation of the ISS has generated significant challenges that have ultimately impacted resources available to the program's primary mission: research. To address this, program personnel routinely perform trade-off studies on alternative options to enhance research. The approach, content level of analysis and resulting outputs of these studies vary due to many factors, however, complicating the Program Manager's job of selecting the best option. To address this, the program requested a framework be developed to evaluate multiple research-enhancing options in a thorough, disciplined and repeatable manner, and to identify the best option on the basis of cost, benefit and risk. The resulting framework consisted of a systematic methodology and a decision-support toolset. The framework provides quantifiable and repeatable means for ranking research-enhancing options for the complex and multiple-constraint domain of the space research laboratory. This paper describes the development, verification and validation of this framework and provides observations on its operational use.

Web-Based Engine for Program Curriculum Designers

Science.gov (United States)

Hamam, H.; Loucif, S.

2009-01-01

Educational institutions pay careful attention to the design of program curricula, which represent a framework to meet institutional goals and missions. Of course, the success of any institution depends highly on the quality of its program curriculum. The development of such a curriculum and, more importantly, the evaluation of its quality are…

GCRA review and appraisal of HTGR reactor-core-design program

International Nuclear Information System (INIS)

1980-09-01

The reactor-core-design program has as its principal objective and responsibility the design and resolution of major technical issues for the reactor core and core components on a schedule consistent with the plant licensing and construction program. The task covered in this review includes three major design areas: core physics, core thermal and hydraulic performance fuel element design, and in-core fuel performance evaluation

Design considerations for a superconducting linac as an option for the ESS

CERN Document Server

Bräutigam, W F; Schug, G; Zaplatin, E N; Meads, P F; Senichev, Yu V

1999-01-01

An approach for a superconducting high-current proton linac for the ESS has been discussed as an option in the "Proposal for a Next Generation Neutron Source for Europe-the European Spallation Source (ESS)". The following work studies the technical and economic conditions for a superconducting linac at the high-energy end of the proposed accelerator system. The use of superconducting elliptical cavities for the acceleration of high-energetic particles beta =v/c-1 is certainly state of the art. This is documented by many activities (TJNAF, TESLA, LEP, LHC, and KEK). A design study for the cavities is described in another paper on this conference. For low energy particles ( beta <<1) quarter wave type cavities and spoke-type cavities have been discussed. The main motivation for this study is the expectation of significant cost reduction in terms of operational and possibly investment cost. (5 refs).

Proceedings of the Management options information seminar

International Nuclear Information System (INIS)

2002-01-01

This seminar was held in order to provide an opportunity to participants to broaden their knowledge concerning the numerous management options that are available when dealing with emissions generated by the electric power sector. It also represented an opportunity to gather information with regard to a host of different options to support the Electricity Project Team. The presentations centred on topics such as assessment, design and development of management options for the emissions of the electric power industry in Alberta. The legal, economic, social and environmental aspects were considered by the speakers for the options, and the perspectives included experience gained from hands on projects and initiatives. The reasons underlying the selection of options were revealed and lessons learned examined. Of the 14 presentations and the closing remarks speech, two presentations were included in this database. refs., tabs., figs

Object-oriented design and programming with C++ your hands-on guide to C++ programming, with special emphasis on design, testing, and reuse

CERN Document Server

Leach, Ronald

2014-01-01

Object-Oriented Design and Programming with C++: Your Hands-On Guide to C++ Programming, with Special Emphasis on Design, Testing, and Reuse provides a list of software engineering principles to guide the software development process. This book presents the fundamentals of the C++ language.Organized into two parts encompassing 10 chapters, this book begins with an overview of C++ and describes object-oriented programming and the history of C++. This text then introduces classes, polymorphism, inheritance, and overloading. Other chapters consider the C++ preprocessor and organization of class l

Logic-programming language enriches design processes

Energy Technology Data Exchange (ETDEWEB)

Kitson, B.; Ow-Wing, K.

1984-03-22

With the emergence of a set of high-level CAD tools for programmable logic devices, designers can translate logic into functional custom devices simply and efficiently. The core of the package is a blockstructured hardware description language called PLPL, for ''programmable-logic programming language.'' The cheif advantage of PLPL lies in its multiple input formats, which permit different design approaches for a variety of design problems. The higher the level of the approach, the closer PLPL will come to directly specifying the desired function. Intermediate steps in the design process can be eliminated, along with the errors that might have been generated during those steps.

A COMPUTER APPLICATION FOR THE ARCHITECTURAL PROGRAM DEVELOPMENT IN DESIGN EDUCATION

Directory of Open Access Journals (Sweden)

Daniel de Carvalho Moreira

2012-02-01

Full Text Available The development of the architectural program in the design studio faces several difficulties. The purpose of the program is to describe the conditions where the building being designed will operate; this requires a lot of information and organization. Due to its complexity, the architetural program definition in the disciplines of design is often simplified. This article discusses such issue and proposes a computer application (SINFORMA that gathers information about the building and the theme of the project in order to develop the architectural program based on structures proposed by bibliographic references. The SINFORMA is composed by a framework which includes a data base and modules which analyze and organize functional requirements, according to the Problem Seeking method and the contemporary values of architecture enumerated by Hershberger. It is discussed how the application can be applied in design education and how it offers students a practical approach and a comprehensive data analysis for the design of built environment. Keywords: Architectural programming, Architectural design, Education.

The differential option in LWR-WIMS

International Nuclear Information System (INIS)

Halsall, M.J.

1979-04-01

In an LWRWIMS calculation of a fuel assembly, the user normally designates several fuel pins as being of the same type. If these pins are physically identical, and similarly situated with respect to poisons and water gaps this seems a reasonable thing to do. However, unless the pins so designated are symmetrically placed within the assembly they will in practice burn up at different rates so that at any given irradiation they will have different isotopic compositions and macroscopic cross sections. The simple option in LWRWIMS assumes that all pins designated to be of a certain type deplete at an appropriate average rate and therefore have equal cross sections at all irradiations. The original differential option which attempted to compensate for this approximation has been shown to have serious defects and a new method has been developed to replace it. The new differential option in LWRWIMS, in which each pin is depleted independently at a rate determined by the local flux and spectrum, is a significant improvement on the old method. It is conceptually simpler and therefore less prone to failure, it is particularly suited to calculating isotopic spatial distributions and it costs no more in computing time. (U.K.)

Social Media in Diabetes Education: A Viable Option?

Science.gov (United States)

Cooper, Julie; Cox, Jill N.; Corbin, Marilyn A.

2012-01-01

As Extension educators are encouraged to implement more cost-effective and efficient means of programming, the use of Web-based social media has become a popular option. Penn State Extension implemented a social media awareness survey among participants in its community-based diabetes education program to determine familiarity with this medium,…

Evaluation of storage/transportation options to support criteria development for the Phase I MRS

International Nuclear Information System (INIS)

Sorenson, K.B.; Brown, N.N.; Bennett, P.C.; Lake, W.

1991-01-01

The DOE's Office of Civilian Waste Management (OCRWM) plans to develop an interim storage facility to enable acceptance of spent fuel in 1998. It is estimated that this interim storage facility would be needed for about two years. A Monitored Retrievable Storage (MRS) facility is anticipated in 2000 and a repository in 2010. Acceptance and transport of spent fuel by DOE/OCRWM in 1998 will require an operating transportation system. Because this interim storage facility is not yet defined, development of an optimally compatible transportation system is not a certainty. In order to assure a transport capability for 1998 acceptance of spent fuel, it was decided that the OCRWM transportation program had to identify likely options for an interim storage facility, including identification of the components needed for compatibility between likely interim storage facility options and transportation. Primary attention was given to existing hardware, although conceptual designs were also considered. A systems-based probabilistic decision model was suggested by Sandia National Labs. and accepted by DOE/OCRWM's transportation program. Performance of the evaluation task involved several elements of the transportation program. This paper describes the decision model developed to accomplish this task, along with some of the results and conclusions

Retrieval options study

International Nuclear Information System (INIS)

1980-03-01

This Retrieval Options Study is part of the systems analysis activities of the Office of Nuclear Waste Isolation to develop the scientific and technological bases for radioactive waste repositories in various geologic media. The study considers two waste forms, high level waste and spent fuel, and defines various classes of waste retrieval and recovery. A methodology and data base are developed which allow the relative evaluation of retrieval and recovery costs and the following technical criteria: safety; technical feasibility; ease of retrieval; probable intact retrieval time; safeguards; monitoring; criticality; and licensability. A total of 505 repository options are defined and the cost and technical criteria evaluated utilizing a combination of facts and engineering judgments. The repositories evaluated are selected combinations of the following parameters: Geologic Media (salt, granite, basalt, shale); Retrieval Time after Emplacement (5 and 25 years); Emplacement Design (nominal hole, large hole, carbon steel canister, corrosion resistant canister, backfill in hole, nominal sleeves, thick wall sleeves); Emplacement Configuration (single vertical, multiple vertical, single horizontal, multiple horizontal, vaults; Thermal Considerations; (normal design, reduced density, once-through ventilation, recirculated ventilation); Room Backfill; (none, run-of-mine, early, 5 year delay, 25 year delay, decommissioned); and Rate of Retrieval;

Hanford Site waste tank farm facilities design reconstitution program plan

International Nuclear Information System (INIS)

Vollert, F.R.

1994-01-01

Throughout the commercial nuclear industry the lack of design reconstitution programs prior to the mid 1980's has resulted in inadequate documentation to support operating facilities configuration changes or safety evaluations. As a result, many utilities have completed or have ongoing design reconstitution programs and have discovered that without sufficient pre-planning their program can be potentially very expensive and may result in end-products inconsistent with the facility needs or expectations. A design reconstitution program plan is developed here for the Hanford waste tank farms facility as a consequence of the DOE Standard on operational configuration management. This design reconstitution plan provides for the recovery or regeneration of design requirements and basis, the compilation of Design Information Summaries, and a methodology to disposition items open for regeneration that were discovered during the development of Design Information Summaries. Implementation of this plan will culminate in an end-product of about 30 Design Information Summary documents. These documents will be developed to identify tank farms facility design requirements and design bases and thereby capture the technical baselines of the facility. This plan identifies the methodology necessary to systematically recover documents that are sources of design input information, and to evaluate and disposition open items or regeneration items discovered during the development of the Design Information Summaries or during the verification and validation processes. These development activities will be governed and implemented by three procedures and a guide that are to be developed as an outgrowth of this plan

Design option of heat exchanger for the next generation nuclear plant - HTR2008-58175

International Nuclear Information System (INIS)

Oh, C. H.; Kim, E. S.

2008-01-01

The Next Generation Nuclear Plant (NGNP), a very High temperature Gas-Cooled Reactor (VHTR) concept, will provide the first demonstration of a closed-loop Brayton cycle at a commercial scale, producing a few hundred megawatts of power in the form of electricity and hydrogen. The power conversion unit (PCU) for the NGNP will take advantage of the significantly higher reactor outlet temperatures of the VHTRs to provide higher efficiencies than can be achieved with the current generation of light water reactors. Besides demonstrating a system design that can be used directly for subsequent commercial deployment, the NGNP will demonstrate key technology elements that can be used in subsequent advanced power conversion systems for other Generation IV reactors. In anticipation of the design, development and procurement of an advanced power conversion system for the NGNP, the system integration of the NGNP and hydrogen plant was initiated to identify the important design and technology options that must be considered in evaluating the performance of the proposed NGNP. As part of the system integration of the VHTRs and the hydrogen production plant, the intermediate heat exchanger is used to transfer the process heat from VHTRs to the hydrogen plant. Therefore, the design and configuration of the intermediate heat exchanger is very important. This paper will include analysis of one stage versus two stage heat exchanger design configurations and simple stress analyses of a printed circuit heat exchanger (PCHE), helical coil heat exchanger, and shell/tube heat exchanger. (authors)

State Options for Supporting Delinquency Prevention: A Working Paper.

Science.gov (United States)

Croan, Gerald M.; And Others

A supplement to the related document "Delinquency Prevention: Theories and Strategies," this paper analyzes the options for state agencies (particularly state planning agencies participating in the Law Enforcement Assistance Administration formula grant program) to promote and support program forms recommended in the companion document.…

Integrating Professional Development into STEM Graduate Programs: Student-Centered Programs for Career Preparation

Science.gov (United States)

Lautz, L.; McCay, D.; Driscoll, C. T.; Glas, R. L.; Gutchess, K. M.; Johnson, A.; Millard, G.

2017-12-01

Recognizing that over half of STEM Ph.D. graduates are finding work outside of academia, a new, NSF-funded program at Syracuse University, EMPOWER (or Education Model Program on Water-Energy Research) is encouraging its graduate students to take ownership of their graduate program and design it to meet their anticipated needs. Launched in 2016, EMPOWER's goal is to prepare graduate students for careers in the water-energy field by offering targeted workshops, professional training coursework, a career capstone experience, a professional development mini-grant program, and an interdisciplinary "foundations" seminar. Through regular student feedback and program evaluation, EMPOWER has learned some important lessons this first year: career options and graduate students' interests are diverse, requiring individualized programs designed to meet the needs of prospective employers and employees; students need exposure to the range of careers in their field to provide a roadmap for designing their own graduate school experience; effective programs nurture a culture that values professional development thereby giving students permission to pursue career paths and professional development opportunities that meet their own needs and interests; and existing university resources support the effective and efficient integration of professional development activities into graduate programs. Many of the positive outcomes experienced by EMPOWER students may be achieved in departmental graduate programs with small changes to their graduate curricula.

Stock Option Compensation and Managerial Turnover

OpenAIRE

Raluca Georgiana NASTASESCU

2009-01-01

This study examines the association between managerial turnover and equity-based compensation. I investigate whether stock options act to bond executives to their firms and whether retention of managers is a motivation of companies in designing CEO incentive contracts. The results show that stock options do negatively influence the probability of a CEO leaving the company. The monetary cost of losing the value of equity-based compensation package keeps the manager with his company. I also fin...

Managing hydroclimatological risk to water supply with option contracts and reservoir index insurance

Science.gov (United States)

Brown, Casey; Carriquiry, Miguel

2007-11-01

This paper explores the performance of a system of economic instruments designed to facilitate the reduction of hydroclimatologic variability-induced impacts on stakeholders of shared water supply. The system is composed of bulk water option contracts between urban water suppliers and agricultural users and insurance indexed on reservoir inflows. The insurance is designed to cover the financial needs of the water supplier in situations where the option is likely to be exercised. Insurance provides the irregularly needed funds for exercising the water options. The combined option contract - reservoir index insurance system creates risk sharing between sectors that is currently lacking in many shared water situations. Contracts are designed for a shared agriculture - urban water system in Metro Manila, Philippines, using optimization and Monte Carlo analysis. Observed reservoir inflows are used to simulate contract performance. Results indicate the option - insurance design effectively smooths water supply costs of hydrologic variability for both agriculture and urban water.

Automated a complex computer aided design concept generated using macros programming

Science.gov (United States)

Rizal Ramly, Mohammad; Asrokin, Azharrudin; Abd Rahman, Safura; Zulkifly, Nurul Ain Md

2013-12-01

Changing a complex Computer Aided design profile such as car and aircraft surfaces has always been difficult and challenging. The capability of CAD software such as AutoCAD and CATIA show that a simple configuration of a CAD design can be easily modified without hassle, but it is not the case with complex design configuration. Design changes help users to test and explore various configurations of the design concept before the production of a model. The purpose of this study is to look into macros programming as parametric method of the commercial aircraft design. Macros programming is a method where the configurations of the design are done by recording a script of commands, editing the data value and adding a certain new command line to create an element of parametric design. The steps and the procedure to create a macro programming are discussed, besides looking into some difficulties during the process of creation and advantage of its usage. Generally, the advantages of macros programming as a method of parametric design are; allowing flexibility for design exploration, increasing the usability of the design solution, allowing proper contained by the model while restricting others and real time feedback changes.

Automated a complex computer aided design concept generated using macros programming

International Nuclear Information System (INIS)

Ramly, Mohammad Rizal; Asrokin, Azharrudin; Rahman, Safura Abd; Zulkifly, Nurul Ain Md

2013-01-01

Changing a complex Computer Aided design profile such as car and aircraft surfaces has always been difficult and challenging. The capability of CAD software such as AutoCAD and CATIA show that a simple configuration of a CAD design can be easily modified without hassle, but it is not the case with complex design configuration. Design changes help users to test and explore various configurations of the design concept before the production of a model. The purpose of this study is to look into macros programming as parametric method of the commercial aircraft design. Macros programming is a method where the configurations of the design are done by recording a script of commands, editing the data value and adding a certain new command line to create an element of parametric design. The steps and the procedure to create a macro programming are discussed, besides looking into some difficulties during the process of creation and advantage of its usage. Generally, the advantages of macros programming as a method of parametric design are; allowing flexibility for design exploration, increasing the usability of the design solution, allowing proper contained by the model while restricting others and real time feedback changes

Near-term hybrid vehicle program, phase 1

Science.gov (United States)

1979-01-01

The preliminary design of a hybrid vehicle which fully meets or exceeds the requirements set forth in the Near Term Hybrid Vehicle Program is documented. Topics addressed include the general layout and styling, the power train specifications with discussion of each major component, vehicle weight and weight breakdown, vehicle performance, measures of energy consumption, and initial cost and ownership cost. Alternative design options considered and their relationship to the design adopted, computer simulation used, and maintenance and reliability considerations are also discussed.

Lighting Options for Homes.

Energy Technology Data Exchange (ETDEWEB)

Baker, W.S.

1991-04-01

This report covers many aspects of various lighting options for homes. Types of light sources described include natural light, artificial light, incandescent lamps, fluorescent lamps, and high intensity discharge lamps. A light source selection guide gives the physical characteristics of these, design considerations, and common applications. Color, strategies for efficient lighting, and types of lighting are discussed. There is one section giving tips for various situations in specific rooms. Rooms and types of fixtures are shown on a matrix with watts saved by using the recommended type lighting for that room and room location. A major emphasis of this report is saving energy by utilizing the most suitable, recommended lighting option. (BN)

Energy exotic options

International Nuclear Information System (INIS)

Kaminski, V.; Gibner, S.; Pinnamaneni, K.

1999-01-01

This chapter with 88 references focuses on the use of exotic options to control exposure to energy prices. Exotic options are defined, and the conversion of a standard option into an exotic option and pricing models are examined. Pricing and hedging exotic options, path-dependent options, multi-commodity options, options on the minimum-or-maximum of two commodities, compound options, digital options, hybrid and complex structures, and natural gas daily options are described. Formulas for option pricing for vanilla, barrier, compound, options on minimum or maximum of two assets, and look back options are given in an appendix

Definition study of a Variable Cycle Experimental Engine (VCEE) and associated test program and test plan

Science.gov (United States)

Allan, R. D.

1978-01-01

The Definition Study of a Variable Cycle Experimental Engine (VCEE) and Associated Test Program and Test Plan, was initiated to identify the most cost effective program for a follow-on to the AST Test Bed Program. The VCEE Study defined various subscale VCE's based on different available core engine components, and a full scale VCEE utilizing current technology. The cycles were selected, preliminary design accomplished and program plans and engineering costs developed for several program options. In addition to the VCEE program plans and options, a limited effort was applied to identifying programs that could logically be accomplished on the AST Test Bed Program VCE to extend the usefulness of this test hardware. Component programs were provided that could be accomplished prior to the start of a VCEE program.

Data warehousing in disease management programs.

Science.gov (United States)

Ramick, D C

2001-01-01

Disease management programs offer the benefits of lower disease occurrence, improved patient care, and lower healthcare costs. In such programs, the key mechanism used to identify individuals at risk for targeted diseases is the data warehouse. This article surveys recent warehousing techniques from HMOs to map out critical issues relating to the preparation, design, and implementation of a successful data warehouse. Discussions of scope, data cleansing, and storage management are included in depicting warehouse preparation and design; data implementation options are contrasted. Examples are provided of data warehouse execution in disease management programs that identify members with preexisting illnesses, as well as those exhibiting high-risk conditions. The proper deployment of successful data warehouses in disease management programs benefits both the organization and the member. Organizations benefit from decreased medical costs; members benefit through an improved quality of life through disease-specific care.

Performance and fuel cycle cost analysis of one Janus 30 conceptual design for several fuel element design options

Energy Technology Data Exchange (ETDEWEB)

Nurdin, Martias [Research Centre for Nuclear Techniques, National Atomic Energy Agency (Indonesia); Matos, J E; Freese, K E [RERTR Program, Argonne National Laboratory (United States)

1983-09-01

The performance and fuel cycle costs for a 25 MW, JANUS 30 reactor conceptual design by INTERATOM, Federal Republic of Germany, for BATAN, Republic of Indonesia have been studied using 19.75% enriched uranium in four fuel element design options. All of these fuel element designs have either been proposed by INTERATOM for various reactors or are currently in use with 93% enriched uranium in reactors in the Federal Republic of Germany. Aluminide, oxide, and silicide fuels were studied for selected designs using the range of uranium densities that are either currently qualified or are being developed and demonstrated internationally. These uranium densities include 1.7-2.3 g/cm{sup 3} in aluminide fuel, 1.7-3.2 g/cm{sup 3} in oxide fuel, and 2.9-6.8 g/cm{sup 3} in silicide fuel. As of November 1982) both the aluminide and the oxide fuels with about 1.7 g U/cm{sup 3} are considered to be fully-proven for licensing purposes. Irradiation screening and proof testing of fuels with uranium densities greater than 1.7 g/cm{sup 3} are currently in progress, and these tests need to be completed in order to obtain licensing authorization for routine reactor use. To assess the long-term fuel adaptation strategy as well as the present fuel acceptance, reactor performance and annual fuel cycle costs were computed for seventeen cases based on a representative end-of-cycle excess reactivity and duty factor. In addition, a study was made to provide data for evaluating the trade-off between the increased safety associated with thicker cladding and the economic penalty due to increased fuel consumption. (author)

Designing and optimising anaerobic digestion systems: A multi-objective non-linear goal programming approach

International Nuclear Information System (INIS)

Nixon, J.D.

2016-01-01

This paper presents a method for optimising the design parameters of an anaerobic digestion (AD) system by using first-order kinetics and multi-objective non-linear goal programming. A model is outlined that determines the ideal operating tank temperature and hydraulic retention time, based on objectives for minimising levelised cost of electricity, and maximising energy potential and feedstock mass reduction. The model is demonstrated for a continuously stirred tank reactor processing food waste in two case study locations. These locations are used to investigate the influence of different environmental and economic climates on optimal conditions. A sensitivity analysis is performed to further examine the variation in optimal results for different financial assumptions and objective weightings. The results identify the conditions for the preferred tank temperature to be in the psychrophilic, mesophilic or thermophilic range. For a tank temperature of 35 °C, ideal hydraulic retention times, in terms of achieving a minimum levelised electricity cost, were found to range from 29.9 to 33 days. Whilst there is a need for more detailed information on rate constants for use in first-order models, multi-objective optimisation modelling is considered to be a promising option for AD design. - Highlights: • Nonlinear goal programming is used to optimise anaerobic digestion systems. • Multiple objectives are set including minimising the levelised cost of electricity. • A model is developed and applied to case studies for the UK and India. • Optimal decisions are made for tank temperature and retention time. • A sensitivity analysis is carried out to investigate different model objectives.

An overview of the Douglas Aircraft Company Aeroelastic Design Optimization Program (ADOP)

Science.gov (United States)

Dodd, Alan J.

1989-01-01

From a program manager's viewpoint, the history, scope and architecture of a major structural design program at Douglas Aircraft Company called Aeroelastic Design Optimization Program (ADOP) are described. ADOP was originally intended for the rapid, accurate, cost-effective evaluation of relatively small structural models at the advanced design level, resulting in improved proposal competitiveness and avoiding many costly changes later in the design cycle. Before release of the initial version in November 1987, however, the program was expanded to handle very large production-type analyses.

Towards Design of Sustainable Energy Systems in Developing Countries: Centralized and Localized Options

Science.gov (United States)

Kursun, Berrin

Energy use in developing countries is projected to equal and exceed the demand in developed countries in the next five years. Growing concern about environmental problems, depletion and price fluctuation of fossil fuels pushes the efforts for meeting energy demand in an environmentally friendly and sustainable way. Hence, it is essential to design energy systems consisting of centralized and localized options that generate the optimum energy mix to meet this increasing energy demand in a sustainable manner. In this study, we try to answer the question, "How can the energy demand in Rampura village be met sustainably?" via two centralized clean coal (CCC) technology and three localized energy technology options analyzed. We perform the analysis of these energy technologies through joint use of donor-side analysis technique emergy analysis (EA) and user-side analysis technique life cycle assessment (LCA). Sustainability of such an energy combination depends on its reliance on renewable inputs rather than nonrenewable or purchased inputs. CCC technologies are unsustainable energy systems dependent on purchased external inputs almost 100%. However, increased efficiency and significantly lower environmental impacts of CCC technologies can lead to more environmentally benign utilization of coal as an energy source. CCC technologies supply electricity at a lower price compared to the localized energy options investigated. Localized energy options analyzed include multi-crystalline solar PV, floating drum biogas digester and downdraft biomass gasifier. Solar PV has the lowest water and land use, however, solar electricity has the highest price with a high global warming potential (GWP). Contrary to general opinion, solar electricity is highly non-renewable. Although solar energy is a 100% renewable natural resource, materials utilized in the production of solar panels are mostly non-renewable purchased inputs causing the low renewability of solar electricity. Best

Buildings energy management program workshop design. Final report

Energy Technology Data Exchange (ETDEWEB)

None

1978-12-01

This document describes activities undertaken by Honeywell's Energy Resources Center for design and development of the format, content, and materials that were used in conducting 129 one-day energy management workshops for specific commercial business audiences. The Building Energy Management Workshop Program was part of a National Workshop Program that was intended to increase awareness of energy-related issues and to encourage energy-conservation actions on the part of commercial and industrial sectors. The total effort included executive conferences for chief executive officers and other senior management personnel; industrial energy-conservation workshops directed at plant management and engineering personnel; vanpooling workshops designed to inform and encourage business in implementing a vanpooling program for employees; and the building energy-management workshops specifically developed for managers, owners, and operators of office and retail facilities, restaurants, and supermarkets. The total program spanned nearly two years and reached approximately 2,500 participants from all parts of the U.S. A detailed followup evaluation is still being conducted to determine the impact of this program in terms of conservation action undertaken by workshop participants.

Preliminary evaluation of crisis-relocation fallout-shelter options. Volume 2. Detailed analysis

International Nuclear Information System (INIS)

Santini, D.J.; Clinch, J.M.; Davis, F.H.; Hill, L.G.; Lynch, E.P.; Tanzman, E.A.; Wernette, D.R.

1982-12-01

This report presents a preliminary, detailed evaluation of various shelter options for use if the President orders crisis relocation of the US urban population because of strong expectation of a nuclear war. The availability of livable shelter space at 40 ft 2 per person (congregate-care space) by state is evaluated. Options are evaluated for construction of fallout shelters allowing 10 ft 2 per person - such shelters are designed to provide 100% survival at projected levels of radioactive fallout. The FEMA concept of upgrading existing buildings to act as fallout shelters can, in principle, provide adequate shelter throughout most of the US. Exceptions are noted and remedies proposed. In terms of upgrading existing buildings to fallout shelter status, great benefits are possible by turning away from a standard national approach and adopting a more site-specific approach. Existing FEMA research provides a solid foundation for successful crisis relocation planning, but the program can be refined by making suitable modifications in its locational, engineering, and institutionally specific elements

The Comparing Options for Management: Patient-centered Results for Uterine Fibroids (COMPARE-UF) Registry: Rationale and Design.

Science.gov (United States)

Stewart, Elizabeth A; Lytle, Barbara L; Thomas, Laine; Wegienka, Ganesa R; Jacoby, Vanessa; Diamond, Michael P; Nicholson, Wanda K; Anchan, Raymond M; Venable, Sateria; Wallace, Kedra; Marsh, Erica E; Maxwell, George L; Borah, Bijan J; Catherino, William H; Myers, Evan R

2018-05-08

To design and establish a uterine fibroid (UF) registry based in the United States (US) to provide comparative effectiveness data regarding UF treatment. We report here the design and initial recruitment for the Comparing Options for Management: Patient-centered Results for Uterine Fibroids (COMPARE-UF) registry (Clinicaltrials.gov, NCT02260752), funded by the Agency for Healthcare Research and Quality (AHRQ) in collaboration with the-Patient-Centered Outcomes Research Institute (PCORI). COMPARE-UF is designed to help answer critical questions about treatment options for women with symptomatic UF. Women undergoing a procedure for UF (hysterectomy, myomectomy [abdominal, hysteroscopic, vaginal and laparoscopic/robotic], endometrial ablation, radiofrequency fibroid ablation, uterine artery embolization, magnetic resonance guided focused ultrasound or progestin-releasing intrauterine device insertion) at one of the COMPARE-UF sites are invited to participate in a prospective registry with three years follow-up for post-procedural outcomes. Enrolled participants provide annual follow-up through an online portal or through traditional phone contact. A central data abstraction center provides information obtained from imaging, operative or procedural notes and pathology reports. Women with uterine fibroids and other stakeholders are a key part of the COMPARE-UF registry and participate at all points from study design to dissemination of results. We built a network of nine clinical sites across the US with expertise in the care of women with UF to capture geographic, racial, ethnic and procedural diversity. Of the initial 2031 women enrolled in COMPARE-UF, 42% are self-identified as Black or African-American and 40% are age 40 years or younger with 16% of participants under age 35. Women undergoing myomectomy comprise the largest treatment group at 46% of all procedures with laparoscopic or robotic myomectomy comprising the largest subset of myomectomies at 19% of all

Residential energy efficiency retrofits: How program design affects participation and outcomes

International Nuclear Information System (INIS)

Hoicka, Christina E.; Parker, Paul; Andrey, Jean

2014-01-01

Better methods of characterizing and addressing heterogeneity in preferences and decision making are needed to stimulate reductions in household greenhouse gas emissions. Four residential energy efficiency programs were delivered consecutively in the Region of Waterloo, Canada, between 1999 and 2011, and each offered a unique combination of information, financial reward structure, and price. A natural quasi-experimental intervention design was employed to assess differences in outcomes across these program structures. Participation at the initial (evaluation by an energy advisor) and follow-up (verification of retrofit) stages, and the material characteristics (e.g., energy performance) were measured and compared between the groups of houses included in each program at each stage. The programs appealed to people with different types of material concerns; each phase of the program was associated with houses with a different mix of material characteristics and depths of recommended and achieved changes. While a performance-based reward attracted fewer houses at each stage than a larger list-based reward, older houses with poorer energy performance were included at each stage. The findings support experimentation with program designs to target sub-populations of housing stock; future program designs should experiment more carefully and with larger performance-based rewards and test parallels with potential carbon market structures. - Highlights: • Multi-program data over 12 years detailing residential energy retrofits. • Natural experimental intervention research design for program evaluation. • Number and attributes of participating households differed by program design. • Financial rewards attracted more participants to the verification stage. • Performance-based incentives have the largest potential for energy savings

Impact of design options on natural circulation performance of the AFR-300 advanced fast reactor

International Nuclear Information System (INIS)

Dunn, F. D.

2002-01-01

The AFR-300, Advanced Fast Reactor (300 Mwe), has been proposed as a Generation IV concept. It could also be used to dispose of surplus weapons grade plutonium or as an actinide burner for transmutation of high level radioactive waste. AFR-300 uses metallic fuel and sodium coolant. The design of AFR-300 takes account of the successful design and operation of EBR-II, but the AFR-300 design includes a number of advances such as an advanced fuel cycle, inspectability and improved economics. One significant difference between AFR-300 and EBR-II is that AFR-300 is considerably larger. Another significant difference is that AFR-300 has no auxiliary EM pump in the primary loop to guarantee positive core flow when the main primary pumps are shut down. Thus, one question that has come up in connection with the AFR-300 design is whether natural circulation flow is sufficient to prevent damage to the core if the primary pumps fail. Insufficient natural circulation flow through the core could result in high cladding temperatures and cladding failure due to eutectic penetration of the cladding by the metal fuel. The rate of eutectic penetration of the cladding is strongly temperature dependent, so cladding failure depends on how hot the cladding gets and how long it is at elevated temperatures. To investigate the adequacy of natural circulation flow, a number of pump failure transients and a number of design options have been analyzed with the SASSYS-1 systems analysis code. This code has been validated for natural circulation behavior by analysis of Shutdown Heat Removal Tests performed in EBR-II. The AFR-300 design includes flywheels on the primary pumps to extend the pump coastdown times, and the size of the flywheels can be picked to give optimum coastdown times. One series of transients that has been run consists of protected loss-of-flow transients with various values for the combined moment of inertia of the pump, the motor and the flywheel giving coastdown times from 70

A Learning Tool and Program Development for Mechatronics Design Education

Science.gov (United States)

Iribe, Masatsugu; Shirahata, Akihiro; Kita, Hiromasa; Sasashige, Yousuke; Dasai, Ryoichi

In this paper we propose a new type educational program for Mechatronics design which contributes to develop the physical sense and problem solving ability of the students who study Mechatronics design. For this program we provide a new handicraft kit of 4-wheeled car which is composed of inexpensive and commonplace parts, and the performance of the assembled 4-wheeled car is sensitive to its assembly arrangement. And then we implemented this program with the handicraft kit to the university freshmen, and verified its effectiveness, and report the results of the program.

Next Generation Melter Optioneering Study - Interim Report

International Nuclear Information System (INIS)

Gray, M.F.; Calmus, R.B.; Ramsey, G.; Lomax, J.; Allen, H.

2010-01-01

The next generation melter (NOM) development program includes a down selection process to aid in determining the recommended vitrification technology to implement into the WTP at the first melter change-out which is scheduled for 2025. This optioneering study presents a structured value engineering process to establish and assess evaluation criteria that will be incorporated into the down selection process. This process establishes an evaluation framework that will be used progressively throughout the NGM program, and as such this interim report will be updated on a regular basis. The workshop objectives were achieved. In particular: (1) Consensus was reached with stakeholders and technology providers represented at the workshop regarding the need for a decision making process and the application of the D 2 0 process to NGM option evaluation. (2) A framework was established for applying the decision making process to technology development and evaluation between 2010 and 2013. (3) The criteria for the initial evaluation in 2011 were refined and agreed with stakeholders and technology providers. (4) The technology providers have the guidance required to produce data/information to support the next phase of the evaluation process. In some cases it may be necessary to reflect the data/information requirements and overall approach to the evaluation of technology options against specific criteria within updated Statements of Work for 2010-2011. Access to the WTP engineering data has been identified as being very important for option development and evaluation due to the interface issues for the NGM and surrounding plant. WRPS efforts are ongoing to establish precisely data that is required and how to resolve this Issue. It is intended to apply a similarly structured decision making process to the development and evaluation of LAW NGM options.

DESIGN AND LICENSING TRENDS OF THE GENERAL EDUCATIONAL PROGRAMS IN LATVIA

OpenAIRE

Mihailovs, Ivans Jānis; Krūmiņa, Aira Aija

2016-01-01

The general education program designing and licensing trends in Latvia in the period from 2010 to 2014 are analyzed in the article. Based on the general education program licensing data, it found that there isn’t a trend to license author’s program in primary education, while the secondary level of education author's programs are designed and licensed more often. The fact that primary education is more licensed programs in mathematics, science and technology, but in general secondary educatio...

Ground-Water Protection and Monitoring Program

Energy Technology Data Exchange (ETDEWEB)

Dresel, P.E.

1995-06-01

This section of the 1994 Hanford Site Environmental Report summarizes the ground-water protection and monitoring program strategy for the Hanford Site in 1994. Two of the key elements of this strategy are to (1) protect the unconfined aquifer from further contamination, and (2) conduct a monitoring program to provide early warning when contamination of ground water does occur. The monitoring program at Hanford is designed to document the distribution and movement of existing ground-water contamination and provides a historical baseline for evaluating current and future risk from exposure to the contamination and for deciding on remedial action options.

Ground-Water Protection and Monitoring Program

International Nuclear Information System (INIS)

Dresel, P.E.

1995-01-01

This section of the 1994 Hanford Site Environmental Report summarizes the ground-water protection and monitoring program strategy for the Hanford Site in 1994. Two of the key elements of this strategy are to (1) protect the unconfined aquifer from further contamination, and (2) conduct a monitoring program to provide early warning when contamination of ground water does occur. The monitoring program at Hanford is designed to document the distribution and movement of existing ground-water contamination and provides a historical baseline for evaluating current and future risk from exposure to the contamination and for deciding on remedial action options

AIF programs supporting industry self-improvement

International Nuclear Information System (INIS)

Szalay, R.A.; Bivens, A.C.

1985-01-01

The Atomic Industrial Forum (AIF) report ''Nuclear Power in America's Future'' identifies those actions that must be taken by both government and industry if the nuclear power option is to be preserved. This includes initiatives that: 1) reduce construction costs and lead times; 2) establish a national energy policy that reflects the role of electricity and the nuclear power component; 3) provide better financial arrangements; 4) reform licensing and regulation; 5) enhance the light water reactor design; 6) inform the public on the benefits and contributions of nuclear power; and 7) complete the fuel cycle. In attempting to solve nuclear power's problems, the AIF has programs that support and push these needed actions. Much of the initiative must be taken by industry to enhance the nuclear power option. This paper discusses some AIF initiatives and programs that support industry self-improvement

Economic analysis of emerald ash borer (Coleoptera: Buprestidae) management options.

Science.gov (United States)

Vannatta, A R; Hauer, R H; Schuettpelz, N M

2012-02-01

Emerald ash borer, Agrilus planipennis (Fairmaire) (Coleoptera: Buprestidae), plays a significant role in the health and extent of management of native North American ash species in urban forests. An economic analysis of management options was performed to aid decision makers in preparing for likely future infestations. Separate ash tree population valuations were derived from the i-Tree Streets program and the Council of Tree and Landscape Appraisers (CTLA) methodology. A relative economic analysis was used to compare a control option (do-nothing approach, only removing ash trees as they die) to three distinct management options: 1) preemptive removal of all ash trees over a 5 yr period, 2) preemptive removal of all ash trees and replacement with comparable nonash trees, or 3) treating the entire population of ash trees with insecticides to minimize mortality. For each valuation and management option, an annual analysis was performed for both the remaining ash tree population and those lost to emerald ash borer. Retention of ash trees using insecticide treatments typically retained greater urban forest value, followed by doing nothing (control), which was better than preemptive removal and replacement. Preemptive removal without tree replacement, which was the least expensive management option, also provided the lowest net urban forest value over the 20-yr simulation. A "no emerald ash borer" scenario was modeled to further serve as a benchmark for each management option and provide a level of economic justification for regulatory programs aimed at slowing the movement of emerald ash borer.

24 CFR 982.634 - Homeownership option: Maximum term of homeownership assistance.

Science.gov (United States)

2010-04-01

... VOUCHER PROGRAM Special Housing Types Homeownership Option § 982.634 Homeownership option: Maximum term of... unit during the time that homeownership payments are made; or (2) Is the spouse of any member of the household who has an ownership interest in the unit during the time homeownership payments are made. (c...

Designing a leadership development program for surgeons.

Science.gov (United States)

Jaffe, Gregory A; Pradarelli, Jason C; Lemak, Christy Harris; Mulholland, Michael W; Dimick, Justin B

2016-01-01

Although numerous leadership development programs (LDPs) exist in health care, no programs have been specifically designed to meet the needs of surgeons. This study aimed to elicit practicing surgeons' motivations and desired goals for leadership training to design an evidence-based LDP in surgery. At a large academic health center, we conducted semistructured interviews with 24 surgical faculty members who voluntarily applied and were selected for participation in a newly created LDP. Transcriptions of the interviews were analyzed using analyst triangulation and thematic coding to extract major themes regarding surgeons' motivations and perceived needs for leadership knowledge and skills. Themes from interview responses were then used to design the program curriculum specifically to meet the leadership needs of surgical faculty. Three major themes emerged regarding surgeons' motivations for seeking leadership training: (1) Recognizing key gaps in their formal preparation for leadership roles; (2) Exhibiting an appetite for personal self-improvement; and (3) Seeking leadership guidance for career advancement. Participants' interviews revealed four specific domains of knowledge and skills that they indicated as desired takeaways from a LDP: (1) leadership and communication; (2) team building; (3) business acumen/finance; and (4) greater understanding of the health care context. Interviews with surgical faculty members identified gaps in prior leadership training and demonstrated concrete motivations and specific goals for participating in a formal leadership program. A LDP that is specifically tailored to address the needs of surgical faculty may benefit surgeons at a personal and institutional level. Copyright © 2016 Elsevier Inc. All rights reserved.

Retrieval options study

Energy Technology Data Exchange (ETDEWEB)

1980-03-01

This Retrieval Options Study is part of the systems analysis activities of the Office of Nuclear Waste Isolation to develop the scientific and technological bases for radioactive waste repositories in various geologic media. The study considers two waste forms, high level waste and spent fuel, and defines various classes of waste retrieval and recovery. A methodology and data base are developed which allow the relative evaluation of retrieval and recovery costs and the following technical criteria: safety; technical feasibility; ease of retrieval; probable intact retrieval time; safeguards; monitoring; criticality; and licensability. A total of 505 repository options are defined and the cost and technical criteria evaluated utilizing a combination of facts and engineering judgments. The repositories evaluated are selected combinations of the following parameters: Geologic Media (salt, granite, basalt, shale); Retrieval Time after Emplacement (5 and 25 years); Emplacement Design (nominal hole, large hole, carbon steel canister, corrosion resistant canister, backfill in hole, nominal sleeves, thick wall sleeves); Emplacement Configuration (single vertical, multiple vertical, single horizontal, multiple horizontal, vaults; Thermal Considerations; (normal design, reduced density, once-through ventilation, recirculated ventilation); Room Backfill; (none, run-of-mine, early, 5 year delay, 25 year delay, decommissioned); and Rate of Retrieval; (same as emplacement, variably slower depending on repository/canister condition).

Program Implementation of Option B+ at a President's Emergency Plan for AIDS Relief-Supported HIV Clinic Improves Clinical Indicators But Not Retention in Care in Mbarara, Uganda.

Science.gov (United States)

Miller, Kathleen; Muyindike, Winnie; Matthews, Lynn T; Kanyesigye, Michael; Siedner, Mark J

2017-08-01

2013 WHO guidelines for prevention of mother to child transmission recommend combination antiretroviral therapy (ART) for all pregnant women, regardless of CD4 count (Option B/B+). We conducted a retrospective analysis of data from a government-operated HIV clinic in Mbarara, Uganda before and after implementation of Option B+ to assess the impact on retention in care. We limited our analysis to women not on ART at the time of their first reported pregnancy with CD4 count >350. We fit regression models to estimate relationships between calendar period (Option A vs. Option B+) and the primary outcome of interest, retention in care. One thousand and sixty-two women were included in the analysis. Women were more likely to start ART within 6 months of pregnancy in the Option B+ period (68% vs. 7%, p Option B+ was associated with a nonsignificant 30% increased odds of retention in care at 1 year [adjusted odds ratio (AOR) = 1.30, 95% CI 0.98-1.73, p = 0.06]. After transition to an Option B+ program, pregnant women with CD4 count >350 were more likely to initiate combination therapy; however, interventions to mitigate losses from HIV care during pregnancy are needed to improve the health of women, children, and families.

20 CFR 416.2035 - Optional supplementation: Additional State options.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Optional supplementation: Additional State options. 416.2035 Section 416.2035 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SUPPLEMENTAL... § 416.2035 Optional supplementation: Additional State options. (a) Residency requirement. A State or...

Analysis of Options Contract, Option Pricing in Agricultural Products

Directory of Open Access Journals (Sweden)

H. Tamidy

2016-03-01

Full Text Available Introduction: Risk is an essential component in the production and sale of agricultural products. Due to the nature of agricultural products, the people who act in this area including farmers and businesspersons encounter unpredictable fluctuations of prices. On the other hand, the firms that process agricultural products also face fluctuation of price of agricultural inputs. Given that the Canola is considered as one of the inputs of product processing factories, control of unpredictable fluctuations of the price of this product would increase the possibility of correct decision making for farmers and managers of food processing industries. The best available tool for control and management of the price risk is the use of future markets and options. It is evident that the pricing is the main pillar in every trade. Therefore, offering a fair price for the options will be very important. In fact, options trading in the options market create cost insurance stopped. In this way, which can reduce the risks of deflation created in the future, if the person entitled to the benefits of the price increase occurs in the future. Unlike the futures, market where the seller had to deliver the product on time, in the options market, there is no such compulsion. In addition, this is one of the strengths of this option contract, because if there is not enough product for delivery to the futures market as result of chilling, in due course, the farmers suffer, but in the options market there will be a loss. In this study, the setup options of rape, as a product, as well as inputs has been paid for industry. Materials and Methods: In this section. The selection criteria of the disposal of asset base for valuation of European put options and call option is been introduced. That for obtain this purpose, some characteristics of the goods must considered: 1-Unpredictable fluctuations price of underlying asset 2 -large underlying asset cash market 3- The possibility

Real Options Valuation of U.S. Federal Renewable Energy Research,Development, Demonstration, and Deployment

Energy Technology Data Exchange (ETDEWEB)

Siddiqui, Afzal S.; Marnay, Chris; Wiser, Ryan H.

2005-03-01

Benefits analysis of US Federal government funded research, development, demonstration, and deployment (RD3) programs for renewable energy (RE) technology improvement typically employs a deterministic forecast of the cost and performance of renewable and nonrenewable fuels. The benefits estimate for a program derives from the difference between two forecasts, with and without the RD3 in place. The deficiencies of the current approach are threefold: (1) it does not consider uncertainty in the cost of non-renewable energy (NRE), and the option or insurance value of deploying RE if and when NRE costs rise; (2) it does not consider the ability of the RD3 manager to adjust the RD3 effort to suit the evolving state of the world, and the option value of this flexibility; and (3) it does not consider the underlying technical risk associated with RD3, and the impact of that risk on the programs optimal level of RD3 effort. In this paper, a rudimentary approach to determining the option value of publicly funded RE RD3 is developed. The approach seeks to tackle the first deficiency noted above by providing an estimate of the options benefit of an RE RD3 program in a future with uncertain NRE costs.While limited by severe assumptions, a computable lattice of options values reveals the economic intuition underlying the decision-making process. An illustrative example indicates how options expose both the insurance and timing values inherent in a simplified RE RD3 program that coarsely approximates the aggregation of current Federal RE RD3.This paper also discusses the severe limitations of this initial approach, and identifies needed model improvements before the approach can adequately respond to the RE RD3 analysis challenge.

Assessment of First Wall and Blanket Options with the Use of Liquid Breeder

International Nuclear Information System (INIS)

Wong, C.P.C.; Malang, S.; Sawan, M.

2005-01-01

As candidate blanket concepts for a U.S. advanced reactor power plant design, with consideration of the time frame for ITER development, we assessed first wall and blanket design concepts based on the use of reduced activation ferritic steel as structural material and liquid breeder as the coolant and tritium breeder. The liquid breeder choice includes the conventional molten salt Li 2 BeF 4 and the low melting point molten salts such as LiBeF 3 and LiNaBeF 4 (FLiNaBe). Both self-cooled and dual coolant molten salt options were evaluated. We have also included the dual coolant leadeutectic Pb-17Li design in our assessment. We take advantage of the molten salt low electrical and thermal conductivity to minimize impacts from the MHD effect and the heat losses from the breeder to the actively cooled steel structure. For the Pb-17Li breeder we employ flow channel inserts of SiC f /SiC composite with low electrical and thermal conductivity to perform respective insulation functions. We performed preliminary assessments of these design options in the areas of neutronics, thermal-hydraulics, safety, and power conversion system. Status of the R and D items of selected high performance blanket concepts is reported. Results from this study will form the technical basis for the formulation of the U.S. ITER test module program and corresponding test plan

Usability Issues in the Design of Novice Programming Systems,

Science.gov (United States)

1996-08-01

lists this as a design principle for novice programming environments. In traditional compiled languages, beginners are also confused by the need to...programming task external knowledge that might interfere with correct under- standing of the language. Most beginner programming errors can be...language for text editing, but [Curtis 1988] found that a textual pseudocode and graphical flowcharts were both bet- ter than natural language in program

Environmental qualification program for new designs

International Nuclear Information System (INIS)

Doerffer, K.

2007-01-01

Qualification of nuclear power plant equipment and components important to safety (ITS) is an integral part of the design process. The qualification methodology differs based on the severity of service conditions (operational and ambient), to which the ITS equipment is exposed. In Canada, the licensing requirements for environmental qualification for new designs are governed by the Canadian Standard Association (CSA) standard, N290.13-2005 titled 'Environmental Qualification of Equipment for CANDU Nuclear Power Plants' and the pre-consultation draft, 'Requirements for Design of Nuclear Power Plants'(DRD), issued for trial use by the Canadian Nuclear Safety Commission (CNSC) in March 2005. This paper will describe AECL's current Environmental Qualification program developed to comply with the above licensing requirements as applied to new designs. The focus will be given to qualification of ITS systems structures and components (SSC) to harsh conditions occurring due to the Design Basis Accidents (DBA). (author)

GRAPHIC, time-sharing magnet design computer programs at Argonne

International Nuclear Information System (INIS)

Lari, R.J.

1974-01-01

This paper describes three magnet design computer programs in use at the Zero Gradient Synchrotron of Argonne National Laboratory. These programs are used in the time sharing mode in conjunction with a Tektronix model 4012 graphic display terminal. The first program in called TRIM, the second MAGNET, and the third GFUN. (U.S.)

Design and validation of general biology learning program based on scientific inquiry skills

Science.gov (United States)

Cahyani, R.; Mardiana, D.; Noviantoro, N.

2018-03-01

Scientific inquiry is highly recommended to teach science. The reality in the schools and colleges is that many educators still have not implemented inquiry learning because of their lack of understanding. The study aims to1) analyze students’ difficulties in learning General Biology, 2) design General Biology learning program based on multimedia-assisted scientific inquiry learning, and 3) validate the proposed design. The method used was Research and Development. The subjects of the study were 27 pre-service students of general elementary school/Islamic elementary schools. The workflow of program design includes identifying learning difficulties of General Biology, designing course programs, and designing instruments and assessment rubrics. The program design is made for four lecture sessions. Validation of all learning tools were performed by expert judge. The results showed that: 1) there are some problems identified in General Biology lectures; 2) the designed products include learning programs, multimedia characteristics, worksheet characteristics, and, scientific attitudes; and 3) expert validation shows that all program designs are valid and can be used with minor revisions. The first section in your paper.

A CAD (Classroom Assessment Design) of a Computer Programming Course

Science.gov (United States)

Hawi, Nazir S.

2012-01-01

This paper presents a CAD (classroom assessment design) of an entry-level undergraduate computer programming course "Computer Programming I". CAD has been the product of a long experience in teaching computer programming courses including teaching "Computer Programming I" 22 times. Each semester, CAD is evaluated and modified…

Designing fractional factorial split-plot experiments using integer programming

DEFF Research Database (Denmark)

Capehart, Shay R.; Keha, Ahmet; Kulahci, Murat

2011-01-01

factorial (FF) design, with the restricted randomisation structure to account for the whole plots and subplots. We discuss the formulation of FFSP designs using integer programming (IP) to achieve various design criteria. We specifically look at the maximum number of clear two-factor interactions...

Risk management with substitution options: Valuing flexibility in small-scale energy systems

Science.gov (United States)

Knapp, Karl Eric

Several features of small-scale energy systems make them more easily adapted to a changing operating environment than large centralized designs. This flexibility is often manifested as the ability to substitute inputs. This research explores the value of this substitution flexibility and the marginal value of becoming a "little more flexible" in the context of real project investment in developing countries. The elasticity of substitution is proposed as a stylized measure of flexibility and a choice variable. A flexible alternative (elasticity > 0) can be thought of as holding a fixed-proportions "nflexible" asset plus a sequence of exchange options---the option to move to another feasible "recipe" each period. Substitutability derives value from following a contour of anticipated variations and from responding to new information. Substitutability value, a "cost savings option", increases with elasticity and price risk. However, the required premium to incrementally increase flexibility can in some cases decrease with an increase in risk. Variance is not always a measure of risk. Tools from stochastic dominance are newly applied to real options with convex payoffs to correct some misperceptions and clarify many common modeling situations that meet the criteria for increased variance to imply increased risk. The behavior of the cost savings option is explored subject to a stochastic input price process. At the point where costs are identical for all alternatives, the stochastic process for cost savings becomes deterministic, with savings directly proportional to elasticity of substitution and price variance. The option is also formulated as a derivative security via dynamic programming. The partial differential equation is solved for the special case of Cobb-Douglas (elasticity = 1) (also shown are linear (infinite elasticity), Leontief (elasticity = 0)). Risk aversion is insufficient to prefer a more flexible alternative with the same expected value. Intertemporal

Comparison between three option, four option and five option multiple choice question tests for quality parameters: A randomized study.

Science.gov (United States)

Vegada, Bhavisha; Shukla, Apexa; Khilnani, Ajeetkumar; Charan, Jaykaran; Desai, Chetna

2016-01-01

Most of the academic teachers use four or five options per item of multiple choice question (MCQ) test as formative and summative assessment. Optimal number of options in MCQ item is a matter of considerable debate among academic teachers of various educational fields. There is a scarcity of the published literature regarding the optimum number of option in each item of MCQ in the field of medical education. To compare three options, four options, and five options MCQs test for the quality parameters - reliability, validity, item analysis, distracter analysis, and time analysis. Participants were 3 rd semester M.B.B.S. students. Students were divided randomly into three groups. Each group was given one set of MCQ test out of three options, four options, and five option randomly. Following the marking of the multiple choice tests, the participants' option selections were analyzed and comparisons were conducted of the mean marks, mean time, validity, reliability and facility value, discrimination index, point biserial value, distracter analysis of three different option formats. Students score more ( P = 0.000) and took less time ( P = 0.009) for the completion of three options as compared to four options and five options groups. Facility value was more ( P = 0.004) in three options group as compared to four and five options groups. There was no significant difference between three groups for the validity, reliability, and item discrimination. Nonfunctioning distracters were more in the four and five options group as compared to three option group. Assessment based on three option MCQs is can be preferred over four option and five option MCQs.

Consideration of a Learning Programming Process based on Software Design for Beginners

OpenAIRE

大村, 基将; 紅林, 秀治

2016-01-01

We considered a learning programming process based on software design for technology education. Lessons of computer program-aided measurement and control are for beginners to learn programming. These lessons are efficient to learn the step of programming, but the main of the lessons are works of typing the sample programming and debugging. Therefore, these lessons have a fundamental lack of the concept of design. Then we considered learning processes of programming and applied the process of ...

Stakeholder Perceptions of Barriers and Solutions to Significant Expansion of Postsecondary Enrollment Options for High School Students

Directory of Open Access Journals (Sweden)

Carl Wozniak

2013-02-01

Full Text Available Post-secondary experiences for students still in high school have been promoted as a means to increase academic rigor and create a better-trained workforce. Yet little is known regarding supports needed to significantly increase such options. This study obtained input from 411 stakeholders in one Midwestern state, including 201 district superintendents, 181 high school principals, and 23 college dual enrollment officers regarding their use of these options, their perceptions of barriers to program expansion, and their ranking of possible solutions to overcome the barriers. Findings demonstrate that all parties find postsecondary options of value, with traditional dual enrollment the most used option. Although all groups identified funding as a primary barrier, other systemic barriers were of great concern. Participants suggest that expansion of Advanced Placement and early and middle college programs, financial assistance for dually enrolled students, and increased program availability for career and technical options would be beneficial.Wozniak, Carl, (2012. Stakeholder Perceptions of Barriers and Solutions to Significant Expansion of Postsecondary Enrollment Options for High School Students. 8(2. Retrieved from www.ijepl.org .

Options to improve energy efficiency for educational building

Science.gov (United States)

Jahan, Mafruha

The cost of energy is a major factor that must be considered for educational facility budget planning purpose. The analysis of energy related issues and options can be complex and requires significant time and detailed effort. One way to facilitate the inclusion of energy option planning in facility planning efforts is to utilize a tool that allows for quick appraisal of the facility energy profile. Once such an appraisal is accomplished, it is then possible to rank energy improvement options consistently with other facility needs and requirements. After an energy efficiency option has been determined to have meaningful value in comparison with other facility planning options, it is then possible to utilize the initial appraisal as the basis for an expanded consideration of additional facility and energy use detail using the same analytic system used for the initial appraisal. This thesis has developed a methodology and an associated analytic model to assist in these tasks and thereby improve the energy efficiency of educational facilities. A detailed energy efficiency and analysis tool is described that utilizes specific university building characteristics such as size, architecture, envelop, lighting, occupancy, thermal design which allows reducing the annual energy consumption. Improving the energy efficiency of various aspects of an educational building's energy performance can be complex and can require significant time and experience to make decisions. The approach developed in this thesis initially assesses the energy design for a university building. This initial appraisal is intended to assist administrators in assessing the potential value of energy efficiency options for their particular facility. Subsequently this scoping design can then be extended as another stage of the model by local facility or planning personnel to add more details and engineering aspects to the initial screening model. This approach can assist university planning efforts to

Design-reliability assurance program application to ACP600

International Nuclear Information System (INIS)

Zhichao, Huang; Bo, Zhao

2012-01-01

ACP600 is a newly nuclear power plant technology made by CNNC in China and it is based on the Generation III NPPs design experience and general safety goals. The ACP600 Design Reliability Assurance Program (D-RAP) is implemented as an integral part of the ACP600 design process. A RAP is a formal management system which assures the collection of important characteristic information about plant performance throughout each phase of its life and directs the use of this information in the implementation of analytical and management process which are specifically designed to meet two specific objects: confirm the plant goals and cost effective improvements. In general, typical reliability assurance program have 4 broad functional elements: 1) Goals and performance criteria; 2) Management system and implementing procedures; 3) Analytical tools and investigative methods; and 4) Information management. In this paper we will use the D-RAP technical and Risk-Informed requirements, and establish the RAM and PSA model to optimize the ACP600 design. Compared with previous design process, the D-RAP is more competent for the higher design targets and requirements, enjoying more creativity through an easier implementation of technical breakthroughs. By using D-RAP, the plants goals, system goals, performance criteria and safety criteria can be easier to realize, and the design can be optimized and more rational

Solar Power System Options for the Radiation and Technology Demonstration Spacecraft

Science.gov (United States)

Kerslake, Thomas W.; Haraburda, Francis M.; Riehl, John P.

2000-01-01

The Radiation and Technology Demonstration (RTD) Mission has the primary objective of demonstrating high-power (10 kilowatts) electric thruster technologies in Earth orbit. This paper discusses the conceptual design of the RTD spacecraft photovoltaic (PV) power system and mission performance analyses. These power system studies assessed multiple options for PV arrays, battery technologies and bus voltage levels. To quantify performance attributes of these power system options, a dedicated Fortran code was developed to predict power system performance and estimate system mass. The low-thrust mission trajectory was analyzed and important Earth orbital environments were modeled. Baseline power system design options are recommended on the basis of performance, mass and risk/complexity. Important findings from parametric studies are discussed and the resulting impacts to the spacecraft design and cost.

Alternative disposal options for transuranic waste

International Nuclear Information System (INIS)

Loomis, G.G.

1994-01-01

Three alternative concepts are proposed for the final disposal of stored and retrieved buried transuranic waste. These proposed options answer criticisms of the existing U.S. Department of Energy strategy of directly disposing of stored transuranic waste in deep, geological salt formations at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. The first option involves enhanced stabilization of stored waste by thermal treatment followed by convoy transportation and internment in the existing WIPP facility. This concept could also be extended to retrieved buried waste with proper permitting. The second option involves in-state, in situ internment using an encapsulating lens around the waste. This concept applies only to previously buried transuranic waste. The third option involves sending stored and retrieved waste to the Nevada Test Site and configuring the waste around a thermonuclear device from the U.S. or Russian arsenal in a specially designed underground chamber. The thermonuclear explosion would transmute plutonium and disassociate hazardous materials while entombing the waste in a national sacrifice area

An optioneering and concept design study for the Astrid sodium-gas heat exchanger matrix

International Nuclear Information System (INIS)

Hattrell, T.; Lopez-Ramirez, S.; Pilatis, N.

2014-01-01

The ASTRID generation IV sodium cooled fast reactor design being developed by the CEA requires a component to transfer heat from the core to the power cycle. One of the ASTRID configurations currently being developed by the CEA uses a sodium to gas heat exchanger (SGHE) to fulfil this function. The design of the SGHE is challenging because of the high temperature of the sodium coolant and the significant pressure differential between the sodium and gas sides of the heat exchanger. This paper presents a study of the options examined for the ASTRID SGHE. A compact, superplastic formed diffusion bonded (SPF-DB) heat exchanger matrix (e.g. SGHE core) is proposed, based on the aerospace technology used by Rolls-Royce to manufacture light and strong wide chord fan blades for gas turbines. The in-house code CHESS is used to examine a number of feasible configurations for the matrix of the heat exchanger component and an optimisation study to maximise the thermal and mechanical performance of the most promising configurations is reported. The optimal matrix geometry identified by the study has a power density for the heat transfer region 157%1 greater than the baseline geometry (authors)

Trends in CAD education in interior design programs

OpenAIRE

Ko, Hye Mi

1990-01-01

This research investigated Computer Aided Design (CAD) education in the interior design. program focusing on educators' opinions about creativity aspects including computer application, teaching materials and teaching methods as well as other trends in CAD education. A questionnaire was sent to one hundred eighty-two members of the Interior Design Educators Council (IDEC). A frequency distribution was used on 69 usable returned surveys to describe the sample characteristi...

Program Helps Design Tests Of Developmental Software

Science.gov (United States)

Hops, Jonathan

1994-01-01

Computer program called "A Formal Test Representation Language and Tool for Functional Test Designs" (TRL) provides automatic software tool and formal language used to implement category-partition method and produce specification of test cases in testing phase of development of software. Category-partition method useful in defining input, outputs, and purpose of test-design phase of development and combines benefits of choosing normal cases having error-exposing properties. Traceability maintained quite easily by creating test design for each objective in test plan. Effort to transform test cases into procedures simplified by use of automatic software tool to create cases based on test design. Method enables rapid elimination of undesired test cases from consideration and facilitates review of test designs by peer groups. Written in C language.

Building interactive simulations in a Web page design program.

Science.gov (United States)

Kootsey, J Mailen; Siriphongs, Daniel; McAuley, Grant

2004-01-01

A new Web software architecture, NumberLinX (NLX), has been integrated into a commercial Web design program to produce a drag-and-drop environment for building interactive simulations. NLX is a library of reusable objects written in Java, including input, output, calculation, and control objects. The NLX objects were added to the palette of available objects in the Web design program to be selected and dropped on a page. Inserting an object in a Web page is accomplished by adding a template block of HTML code to the page file. HTML parameters in the block must be set to user-supplied values, so the HTML code is generated dynamically, based on user entries in a popup form. Implementing the object inspector for each object permits the user to edit object attributes in a form window. Except for model definition, the combination of the NLX architecture and the Web design program permits construction of interactive simulation pages without writing or inspecting code.

Designing and Implementing a Mentoring Program to Support Clinically-Based Teacher Education

Science.gov (United States)

Henning, John E.; Gut, Dianne; Beam, Pamela

2015-01-01

This article describes one teacher preparation program's approach to designing and implementing a mentoring program to support clinically-based teacher education. The design for the program is based on an interview study that compared the mentoring experiences of 18 teachers across three different contexts: student teaching, early field…

Robust Trajectory Option Set planning in CTOP based on Bayesian game model

KAUST Repository

Li, Lichun; Clarke, John-Paul; Feron, Eric; Shamma, Jeff S.

2017-01-01

The Federal Aviation Administration (FAA) rations capacity to reduce en route delay, especially those caused by bad weather. This is accomplished via Collaborative Trajectory Options Program (CTOP) which has been recently developed to provide a mechanism for flight operators to communicate their route preferences for each flight via a Trajectory Option Set (TOS), as well as a mechanism for the FAA to assign the best possible route within the set of trajectories in the TOS for a given flight, i.e. the route with the lowest adjusted cost after consideration of system constraints and the requirements of all flights. The routes assigned to an airline depend not only on the TOS's for its own flights but also on the TOS's of all other flights in the CTOP, which are unknown. This paper aims to provide a detailed algorithm for the airline to design its TOS plan which is robust to the uncertainties of its competitors' TOS's. To this purpose, we model the CTOP problem as a Bayesian game, and use Linear Program (LP) to compute the security strategy in the Bayesian game model. This security strategy guarantees the airline an upper bound on the sum of the assigned times. The numerical results demonstrate the robustness of the strategy, which is not achieved by any other tested strategy.

Robust Trajectory Option Set planning in CTOP based on Bayesian game model

KAUST Repository

Li, Lichun

2017-07-10

The Federal Aviation Administration (FAA) rations capacity to reduce en route delay, especially those caused by bad weather. This is accomplished via Collaborative Trajectory Options Program (CTOP) which has been recently developed to provide a mechanism for flight operators to communicate their route preferences for each flight via a Trajectory Option Set (TOS), as well as a mechanism for the FAA to assign the best possible route within the set of trajectories in the TOS for a given flight, i.e. the route with the lowest adjusted cost after consideration of system constraints and the requirements of all flights. The routes assigned to an airline depend not only on the TOS\\'s for its own flights but also on the TOS\\'s of all other flights in the CTOP, which are unknown. This paper aims to provide a detailed algorithm for the airline to design its TOS plan which is robust to the uncertainties of its competitors\\' TOS\\'s. To this purpose, we model the CTOP problem as a Bayesian game, and use Linear Program (LP) to compute the security strategy in the Bayesian game model. This security strategy guarantees the airline an upper bound on the sum of the assigned times. The numerical results demonstrate the robustness of the strategy, which is not achieved by any other tested strategy.

Design and Development of an MPH Program for Distance Education Delivery

OpenAIRE

Steven R. Hawks

2008-01-01

The Master-s of Public Health (MPH) degree is growing in popularity among a number of higher education institutions throughout the world as a distance education graduate program. This paper offers an overview of program design and development strategies that promote successful distance delivery of MPH programs. Design and development challenges are discussed in terms of type of distance delivery, accreditation, student demand, faculty development, user needs, course conte...

Designing an Elderly Assistance Program Based-on Home Care

Science.gov (United States)

Umusya'adah, L.; Juwaedah, A.; Jubaedah, Y.; Ratnasusanti, H.; Puspita, R. H.

2018-02-01

PKH (Program Keluarga Harapan) is a program of Indonesia’s Government through the ministry of social directorate to accelerate the poverty reduction and the achievement of Millennium Development Goals (MDGs) target as well as the policies development in social protection and social welfare domain or commonly referred to as Indonesian Conditional Cash Transfer (CCT) Program. This research is motivated that existing participants of the family expectation program (PKH) that already exist in Sumedang, Indoensia, especially in the South Sumedang on the social welfare components is only limited to the health checking, while for assisting the elderly based Home Care program there has been no structured and systematic, where as the elderly still need assistance, especially from the family and community environment. This study uses a method of Research and Development with Model Addie which include analysis, design, development, implementation and evaluation. Participants in this study using purposive sampling, where selected families of PKH who provide active assistance to the elderly with 82 participants. The program is designed consists of program components: objectives, goals, forms of assistance, organizing institutions and implementing the program, besides, program modules include assisting the elderly. Form of assistance the elderly cover physical, social, mental and spiritual. Recommended for families and companions PKH, the program can be implemented to meet the various needs of the elderly. For the elderly should introspect, especially in the health and follow the advice recommended by related parties

Design basis programs and improvements in plant operation

International Nuclear Information System (INIS)

Metcalf, M.F.

1991-01-01

Public Service Electric and Gas (PSE and G) Company operates three commercial nuclear power plants in southern New Jersey. The three plants are of different designs and vintages (two pressurized water reactors licensed in 1976 and 1980 and one boiling water reactor licensed in 1986). As the industry recognized the need to develop design basis programs, PSE and G also realized the need after a voluntary 52-day shutdown of one unit because of electrical design basis problems. In its drive to be a premier electric utility, PSE and G has been aggressively active in developing design basis documents (DBDs) with supporting projects and refined uses to obtain the expected value and see the return on investment. Progress on Salem is nearly 75% complete, while Hope Creek is 20% complete. To data, PSE and G has experienced success in the use of DBDs in areas such as development of plant modifications, development of the reliability-centered maintenance program, procedure upgrades, improved document retrieval, resolution of regulatory issues, and training. The paper examines the design basis development process, supporting projects, and expected improvements in plant operations as a result of these efforts

Design of an internal dosimetry program

International Nuclear Information System (INIS)

Wu, C.F.; Goff, T.E.

2004-01-01

Measurement of radiation dose is an essential element of radiation protection programs at nuclear facilities. To protect workers and demonstrate compliance with regulatory requirements, dosimetry programs must be established based on sound technical basis. Historically, external exposure was controlled by occupational dose limits. Internal exposure to radionuclides was limited by maximum permissible body burden and maximum permissible concentration. With the issuance of ICRP 26, ICRP 30, DOE Order 5480.11, DOE/EH-0256T, and the new 10 CFR 20, it has become a requirement that internal dose be assessed and the sum of internal and external doses be maintained below regulatory limits. Nuclear facilities are required to have internal dose evaluation programs adequate to demonstrate compliance with radiation protection standards (RPSs). The Waste Isolation Pilot Plant is a DOE facility designed to demonstrate safe disposal of transuranic (TRU) wastes in an ancient salt bed 2,150 feet underground. Internal dose measurement is required to support waste handling activities. This paper describes the technical basis for the WIPP Internal Dosimetry Program. (author)

Excess plutonium disposition: The deep borehole option

International Nuclear Information System (INIS)

Ferguson, K.L.

1994-01-01

This report reviews the current status of technologies required for the disposition of plutonium in Very Deep Holes (VDH). It is in response to a recent National Academy of Sciences (NAS) report which addressed the management of excess weapons plutonium and recommended three approaches to the ultimate disposition of excess plutonium: (1) fabrication and use as a fuel in existing or modified reactors in a once-through cycle, (2) vitrification with high-level radioactive waste for repository disposition, (3) burial in deep boreholes. As indicated in the NAS report, substantial effort would be required to address the broad range of issues related to deep bore-hole emplacement. Subjects reviewed in this report include geology and hydrology, design and engineering, safety and licensing, policy decisions that can impact the viability of the concept, and applicable international programs. Key technical areas that would require attention should decisions be made to further develop the borehole emplacement option are identified

The genetics of age-related macular degeneration (AMD)--Novel targets for designing treatment options?

Science.gov (United States)

Grassmann, Felix; Fauser, Sascha; Weber, Bernhard H F

2015-09-01

Age-related macular degeneration (AMD) is a progressive disease of the central retina and the main cause of legal blindness in industrialized countries. Risk to develop the disease is conferred by both individual as well as genetic factors with the latter being increasingly deciphered over the last decade. Therapeutically, striking advances have been made for the treatment of the neovascular form of late stage AMD while for the late stage atrophic form of the disease, which accounts for almost half of the visually impaired, there is currently no effective therapy on the market. This review highlights our current knowledge on the genetic architecture of early and late stage AMD and explores its potential for the discovery of novel, target-guided treatment options. We reflect on current clinical and experimental therapies for all forms of AMD and specifically note a persisting lack of efficacy for treatment in atrophic AMD. We further explore the current insight in AMD-associated genes and pathways and critically question whether this knowledge is suited to design novel treatment options. Specifically, we point out that known genetic factors associated with AMD govern the risk to develop disease and thus may not play a role in its severity or progression. Treatments based on such knowledge appear appropriate rather for prevention than treatment of manifest disease. As a consequence, future research in AMD needs to be greatly focused on approaches relevant to the patients and their medical needs. Copyright © 2015 Elsevier B.V. All rights reserved.

Near-term electric vehicle program: Phase I, final report

Energy Technology Data Exchange (ETDEWEB)

Rowlett, B. H.; Murry, R.

1977-08-01

A final report is given for an Energy Research and Development Administration effort aimed at a preliminary design of an energy-efficient electric commuter car. An electric-powered passenger vehicle using a regenerative power system was designed to meet the near-term ERDA electric automobile goals. The program objectives were to (1) study the parameters that affect vehicle performance, range, and cost; (2) design an entirely new electric vehicle that meets performance and economic requirements; and (3) define a program to develop this vehicle design for production in the early 1980's. The design and performance features of the preliminary (baseline) electric-powered passenger vehicle design are described, including the baseline power system, system performance, economic analysis, reliability and safety, alternate designs and options, development plan, and conclusions and recommendations. All aspects of the baseline design were defined in sufficient detail to verify performance expectations and system feasibility.

A Design Study of a Multimedia Instructional Grammar Program with Embedded Tracking

Science.gov (United States)

Koehler, Natalya A.; Thompson, Ann D.; Phye, Gary D.

2011-01-01

This is a design study meant to demonstrate the feasibility of integrating three rather different theoretical perspectives for future efforts in multimedia instructional design. A multimedia instructional grammar program contextualized within the teaching of English as a Second Language (ESL) was developed and evaluated. The program design was…

Preliminary evaluation of crisis-relocation fallout-shelter options. Volume 2. Detailed analysis

Energy Technology Data Exchange (ETDEWEB)

Santini, D.J.; Clinch, J.M.; Davis, F.H.; Hill, L.G.; Lynch, E.P.; Tanzman, E.A.; Wernette, D.R.

1982-12-01

This report presents a preliminary, detailed evaluation of various shelter options for use if the President orders crisis relocation of the US urban population because of strong expectation of a nuclear war. The availability of livable shelter space at 40 ft/sup 2/ per person (congregate-care space) by state is evaluated. Options are evaluated for construction of fallout shelters allowing 10 ft/sup 2/ per person - such shelters are designed to provide 100% survival at projected levels of radioactive fallout. The FEMA concept of upgrading existing buildings to act as fallout shelters can, in principle, provide adequate shelter throughout most of the US. Exceptions are noted and remedies proposed. In terms of upgrading existing buildings to fallout shelter status, great benefits are possible by turning away from a standard national approach and adopting a more site-specific approach. Existing FEMA research provides a solid foundation for successful crisis relocation planning, but the program can be refined by making suitable modifications in its locational, engineering, and institutionally specific elements.

Evaluation of storage/transportation options to support criteria development for the Phase I MRS [Monitored Retrievable Storage

International Nuclear Information System (INIS)

Sorenson, K.B.; Brown, N.N.; Bennett, P.C.; Lake, W.

1991-01-01

The Department of Energy's (DOE) Office of Civilian Waste Management (OCRWM) plans to develop an interim storage facility to enable acceptance of spent fuel in 1998. It is estimated that this interim storage facility would be needed for about two years. A Monitored Retrievable Storage (MRS) facility is anticipated in 2000 and a repository in 2010. Acceptance and transport of spent fuel by DOE/OCRWM in 1998 will require an operating transportation system. Because this interim storage facility is not yet defined, development of an optimally compatible transportation system is not a certainty. In order to assure a transport capability for 1998 acceptance of spent fuel, it was decided that the OCRWM transportation program had to identify likely options for an interim storage facility, including identification of the components needed for compatibility between likely interim storage facility options and transportation. Primary attention was given to existing hardware, although conceptual designs were also considered. A systems-based probabilistic decision model was suggested by Sandia National Laboratories and accepted by DOE/OCRWM's transportation program. Performance of the evaluation task involved several elements of the transportation program. This paper describes the decision model developed to accomplish this task, along with some of the results and conclusions. 1 ref., 4 figs

Multimedia programming using Max/MSP and TouchDesigner

CERN Document Server

Lechner, Patrik

2014-01-01

If you want to learn how to use Max 6 and/or TouchDesigner, or work in audio-visual real-time processing, this is the book for you. It is intended for intermediate users of both programs and can be helpful for artists, designers, musicians, VJs, and researchers. A basic understanding of audio principles is advantageous.

Effective Analysis of C Programs by Rewriting Variability

DEFF Research Database (Denmark)

Iosif-Lazar, Alexandru Florin; Melo, Jean; Dimovski, Aleksandar

2017-01-01

and effective analysis and verification of real-world C program families. Importance. We report some interesting variability-related bugs that we discovered using various state-of-the-art single-program C verification tools, such as Frama-C, Clang, LLBMC.......Context. Variability-intensive programs (program families) appear in many application areas and for many reasons today. Different family members, called variants, are derived by switching statically configurable options (features) on and off, while reuse of the common code is maximized. Inquiry....... Verification of program families is challenging since the number of variants is exponential in the number of features. Existing single-program analysis and verification tools cannot be applied directly to program families, and designing and implementing the corresponding variability-aware versions is tedious...

The New Option Offense for Winning Basketball.

Science.gov (United States)

Walker, A. L.; Donohue, Jack

This reference book for basketball coaches provides a total program of both offensive and defensive strategies and tactics. The emphasis is upon an innovative offensive system with an accompanying defensive plan. The initial chapters deal with the installation of the three series of the New Option Offensive: "Red,""White," and "Blue." A drills…

European passive plant program preliminary safety analyses to support system design

International Nuclear Information System (INIS)

Saiu, Gianfranco; Barucca, Luciana; King, K.J.

1999-01-01

In 1994, a group of European Utilities, together with Westinghouse and its Industrial Partner GENESI (an Italian consortium including ANSALDO and FIAT), initiated a program designated EPP (European Passive Plant) to evaluate Westinghouse Passive Nuclear Plant Technology for application in Europe. In the Phase 1 of the European Passive Plant Program which was completed in 1996, a 1000 MWe passive plant reference design (EP1000) was established which conforms to the European Utility Requirements (EUR) and is expected to meet the European Safety Authorities requirements. Phase 2 of the program was initiated in 1997 with the objective of developing the Nuclear Island design details and performing supporting analyses to start development of Safety Case Report (SCR) for submittal to European Licensing Authorities. The first part of Phase 2, 'Design Definition' phase (Phase 2A) was completed at the end of 1998, the main efforts being design definition of key systems and structures, development of the Nuclear Island layout, and performing preliminary safety analyses to support design efforts. Incorporation of the EUR has been a key design requirement for the EP1000 form the beginning of the program. Detailed design solutions to meet the EUR have been defined and the safety approach has also been developed based on the EUR guidelines. The present paper describes the EP1000 approach to safety analysis and, in particular, to the Design Extension Conditions that, according to the EUR, represent the preferred method for giving consideration to the Complex Sequences and Severe Accidents at the design stage without including them in the design bases conditions. Preliminary results of some DEC analyses and an overview of the probabilistic safety assessment (PSA) are also presented. (author)

Method and simulation program informed decisions in the early stages of building design

DEFF Research Database (Denmark)

Petersen, Steffen; Svendsen, Svend

2010-01-01

variations. The program then presents the output in a way that enables designers to make informed decisions. The method and the program reduce the need for design iterations, reducing time consumption and construction costs, to obtain the intended energy performance and indoor environment....... for making informed decisions in the early stages of building design to fulfil performance requirements with regard to energy consumption and indoor environment. The method is operationalised in a program that utilises a simple simulation program to make performance predictions of user-defined parameter......The early stages of building design include a number of decisions which have a strong influence on the performance of the building throughout the rest of the process. It is therefore important that designers are aware of the consequences of these design decisions. This paper presents a method...

Greenhouse gas mitigation options for Washington State

Energy Technology Data Exchange (ETDEWEB)

Garcia, N.

1996-04-01

President Clinton, in 1993, established a goal for the United States to return emissions of greenhouse gases to 1990 levels by the year 2000. One effort established to help meet this goal was a three part Environmental Protection Agency state grant program. Washington State completed part one of this program with the release of the 1990 greenhouse gas emissions inventory and 2010 projected inventory. This document completes part two by detailing alternative greenhouse gas mitigation options. In part three of the program EPA, working in partnership with the States, may help fund innovative greenhouse gas reduction strategies. The greenhouse gas control options analyzed in this report have a wide range of greenhouse gas reductions, costs, and implementation requirements. In order to select and implement a prudent mix of control strategies, policy makers need to have some notion of the potential change in climate, the consequences of that change and the uncertainties contained therein. By understanding the risks of climate change, policy makers can better balance the use of scarce public resources for concerns that are immediate and present against those that affect future generations. Therefore, prior to analyzing alternative greenhouse gas control measures, this report briefly describes the phenomenon and uncertainties of global climate change, and then projects the likely consequences for Washington state.

Contextual effects and psychological features influencing decoy options: A review and research agenda

Directory of Open Access Journals (Sweden)

David Gonzalez-Prieto

2013-01-01

Full Text Available Purpose: The purpose of this paper is to develop future research proposals aiming to contribute the extant theory which explains decoy effects.Design/methodology/approach: Firstly, a review of the existing literature about decoy options and its interactions with contextual effects that could affect their performance is presented. Next, two research proposals are presented: the introduction of a double decoy choice set and the evaluation of decoy effect under different levels of cognitive effort in a purchasing process.Findings and Originality/value: For the research proposal concerning double decoy choice sets, different hypothesis are introduced based on the different theories aiming to explain the effect of simple decoy choice sets. This hypothesis predict different outcomes for the same experimental design, fact that could provide further support for at least one of the current explanations for decoy effects. Regarding the effect of decoy options under different levels of cognitive effort, implications for experimental design for sequential purchasing process are expected. Especially for those designed with complex options, with many steps or high number of options.Originality/value: Two new research proposal approaches are presented in order enhance the current theory. Moreover, both have managerial implications concerning the real usage of decoy options in reduced choice sets as well as in sequential purchasing processes.

24 CFR 982.635 - Homeownership option: Amount and distribution of monthly homeownership assistance payment.

Science.gov (United States)

2010-04-01

... CHOICE VOUCHER PROGRAM Special Housing Types Homeownership Option § 982.635 Homeownership option: Amount and distribution of monthly homeownership assistance payment. (a) Amount of monthly homeownership... distribution of monthly homeownership assistance payment. 982.635 Section 982.635 Housing and Urban Development...

Designing a flood-risk education program in the Netherlands

NARCIS (Netherlands)

Bosschaert, A.; van der Schee, J.; Kuiper, W.

2016-01-01

This study focused on designing a flood-risk education program to enhance 15-year-old students’ flood-risk perception. In the flood-risk education program, learning processes were modeled in such a way that the arousal of moderate levels of fear should prompt experiential and analytical information

Mississippi Curriculum Framework for Drafting and Design Technology (Program CIP: 48.0102--Architectural Drafting Technology) (Program CIP: 48.0101--General Drafting). Postsecondary Programs.

Science.gov (United States)

Mississippi Research and Curriculum Unit for Vocational and Technical Education, State College.

This document, which is intended for use by community and junior colleges throughout Mississippi, contains curriculum frameworks for the two course sequences of the state's postsecondary-level drafting and design technology program: architectural drafting technology and drafting and design technology. Presented first are a program description and…

A novel method to value real options in health care: the case of a multicohort human papillomavirus vaccination strategy.

Science.gov (United States)

Favato, Giampiero; Baio, Gianluca; Capone, Alessandro; Marcellusi, Andrea; Saverio Mennini, Francesco

2013-07-01

A large number of economic evaluations have already confirmed the cost-effectiveness of different human papillomavirus (HPV) vaccination strategies. Standard analyses might not capture the full economic value of novel vaccination programs because the cost-effectiveness paradigm fails to take into account the value of active management. Management decisions can be seen as real options, a term used to refer to the application of option pricing theory to the valuation of investments in nonfinancial assets in which much of the value is attributable to flexibility and learning over time. The aim of this article was to discuss the potential advantages shown by using the payoff method in the valuation of the cost-effectiveness of competing HPV immunization programs. This was the first study, to the best of our knowledge, to use the payoff method to determine the real option values of 4 different HPV vaccination strategies targeting female subjects aged 12, 15, 18, and 25 years. The payoff method derives the real option value from the triangular payoff distribution of the project's net present value, which is treated as a triangular fuzzy number. To inform the real option model, cost-effectiveness data were derived from an empirically calibrated Bayesian model designed to assess the cost-effectiveness of a multicohort HPV vaccination strategy in the context of the current cervical cancer screening program in Italy. A net health benefit approach was used to calculate the expected fuzzy net present value for each of the 4 vaccination strategies evaluated. Costs per quality-adjusted life-year gained seemed to be related to the number of cohorts targeted: a single cohort of girls aged 12 years (€10,955 [95% CI, -1,021 to 28,212]) revealed the lowest cost among the 4 alternative strategies evaluated. The real option valuation challenged the cost-effectiveness dominance of a single cohort of 12-year-old girls. The simultaneous vaccination of 2 cohorts of girls aged 12 and 15

An application program for fission product decay heat calculations

International Nuclear Information System (INIS)

Pham, Ngoc Son; Katakura, Jun-ichi

2007-10-01

The precise knowledge of decay heat is one of the most important factors in safety design and operation of nuclear power facilities. Furthermore, decay heat data also play an important role in design of fuel discharges, fuel storage and transport flasks, and in spent fuel management and processing. In this study, a new application program, called DHP (Decay Heat Power program), has been developed for exact decay heat summation calculations, uncertainty analysis, and for determination of the individual contribution of each fission product. The analytical methods were applied in the program without any simplification or approximation, in which all of linear and non-linear decay chains, and 12 decay modes, including ground state and meta-stable states, are automatically identified, and processed by using a decay data library and a fission yield data file, both in ENDF/B-VI format. The window interface of the program is designed with optional properties which is very easy for users to run the code. (author)

Balance-of-plant options for the Heat-Pipe Power System

International Nuclear Information System (INIS)

Berte, M.; Capell, B.

1997-09-01

The Heat-Pipe Power System (HPS) is a near-term, low-cost space fission power system with the potential for utilizing various option for balance-of-plant options. The following options have been studied: a low-power thermoelectric design (14-kWe output), a small Brayton cycle system (60--75 kWe), and a large Brayton cycle system (250 kWe). These systems were analyzed on a preliminary basis, including mass, volume, and structure calculations. These analyses have shown that the HPS system can provide power outputs from 10--250 kWe with specific powers of ∼ 14 W/kg for a 14-kWe model to ∼ 100 W/kg for a 250-kWe model. The system designs considered in this study utilize a common component base to permit easy expansion and development

Simulation Packages Expand Aircraft Design Options

Science.gov (United States)

2013-01-01

In 2001, NASA released a new approach to computational fluid dynamics that allows users to perform automated analysis on complex vehicle designs. In 2010, Palo Alto, California-based Desktop Aeronautics acquired a license from Ames Research Center to sell the technology. Today, the product assists organizations in the design of subsonic aircraft, space planes, spacecraft, and high speed commercial jets.

Economic assessment of climate adaptation options for urban drainage design in Odense, Denmark

DEFF Research Database (Denmark)

Zhou, Qianqian; Halsnæs, Kirsten; Arnbjerg-Nielsen, Karsten

2012-01-01

framework is used to give detailed insights of the physical and economic feasibilities of each option. Estimation of marginal benefits of adaptation options are carried out through a step-by-step cost-benefit analysis. The results are aimed at providing important information for decision making on how best......Climate change is likely to influence the water cycle by changing the precipitation patterns, in some cases leading to increased occurrences of precipitation extremes. Urban landscapes are vulnerable to such changes due to the concentrated population and socio-economic values in cities. Feasible...

Transmutation performance analysis on coolant options in a hybrid reactor system design for high level waste incineration

Energy Technology Data Exchange (ETDEWEB)

Hong, Seong-Hee; Siddique, Muhammad Tariq; Kim, Myung Hyun, E-mail: mhkim@khu.ac.kr

2015-11-15

Highlights: • Waste transmutation performance was compared and analyzed for seven different coolant options. • Reactions of fission and capture showed big differences depending on coolant options. • Moderation effect significantly affects on energy multiplication, tritium breeding and waste transmutation. • Reduction of radio-toxicities of TRUs showed different trend to coolant choice from performance of waste transmutation. - Abstract: A fusion–fission hybrid reactor (FFHR) is one of the most attractive candidates for high level waste transmutation. The selection of coolant affects the transmutation performance of a FFHR. LiPb coolant, as a conventional coolant for a FFHR, has problems such as reduction in neutron economic and magneto-hydro dynamics (MHD) pressure drop. Therefore, in this work, transmutation performance is evaluated and compared for various coolant options such as LiPb, H{sub 2}O, D{sub 2}O, Na, PbBi, LiF-BeF{sub 2} and NaF-BeF{sub 2} applicable to a hybrid reactor for waste transmutation (Hyb-WT). Design parameters measuring performance of a hybrid reactor were evaluated by MCNPX. They are k{sub eff}, energy multiplication factor, neutron absorption ratio, tritium breeding ratio, waste transmutation ratio, support ratio and radiotoxicity reduction. Compared to LiPb, H{sub 2}O and D{sub 2}O are not suitable for waste transmutation because of neutron moderation effect. Waste transmutation performances with Na and PbBi are similar to each other and not different much from LiPb. Even though molten salt such as LiF-BeF{sub 2} and NaF-BeF{sub 2} is good for avoiding MHD pressure drop problem, waste transmutation performance is dropped compared with LiPb.

Moderator Configuration Options for ESS

DEFF Research Database (Denmark)

Zanini, L.; Batkov, K.; Klinkby, Esben Bryndt

2016-01-01

The current, still evolving status of the design and the optimization work for the moderator configuration for the European Spallation Source is described. The moderator design has been strongly driven by the low-dimensional moderator concept recently proposed for use in spallation neutron sources...... or reactors. Quasi-two dimensional, disc- or tube-shaped moderators,can provide strong brightness increase (factor of 3 or more) with respect to volume para-H2moderators, which constitute the reference, state-of-the-art technology for high-intensity coupled moderators. In the design process other, more...... conventional, principles were also considered,such as the importance of moderator positioning, of the premoderator, and beam extraction considerations. Different design and configuration options are evaluated and compared with the reference volume moderator configuration described in the ESS Technical Design...

Designing and Programming CICS Applications

CERN Document Server

Horswill, John

2011-01-01

CICS is an application server that delivers industrial-strength, online transaction management for critical enterprise applications. Proven in the market for over 30 years with many of the world's leading businesses, CICS enables today's customers to modernize and extend their applications to take advantage of the opportunities provided by e-business while maximizing the benefits of their existing investments. Designing and Programming CICS Applications will benefit a diverse audience. It introduces new users of IBM's mainframe (OS/390) to CICS features. It shows experienced users how t

Option pricing: a flexible tool to disseminate shared savings contracts.

Science.gov (United States)

Friedberg, Mark W; Buendia, Anthony M; Lauderdale, Katherine E; Hussey, Peter S

2013-08-01

Due to volatility in healthcare costs, shared savings contracts can create systematic financial losses for payers, especially when contracting with smaller providers. To improve the business case for shared savings, we calculated the prices of financial options that payers can "sell" to providers to offset these losses. Using 2009 to 2010 member-level total cost of care data from a large commercial health plan, we calculated option prices by applying a bootstrap simulation procedure. We repeated these simulations for providers of sizes ranging from 500 to 60,000 patients and for shared savings contracts with and without key design features (minimum savings thresholds,bonus caps, cost outlier truncation, and downside risk) and under assumptions of zero, 1%, and 2% real cost reductions due to the shared savings contracts. Assuming no real cost reduction and a 50% shared savings rate, per patient option prices ranged from $225 (3.1% of overall costs) for 500-patient providers to $23 (0.3%) for 60,000-patient providers. Introducing minimum savings thresholds, bonus caps, cost outlier truncation, and downside risk reduced these option prices. Option prices were highly sensitive to the magnitude of real cost reductions. If shared savings contracts cause 2% reductions in total costs, option prices fall to zero for all but the smallest providers. Calculating the prices of financial options that protect payers and providers from downside risk can inject flexibility into shared savings contracts, extend such contracts to smaller providers, and clarify the tradeoffs between different contract designs, potentially speeding the dissemination of shared savings.

Palliative Care Options for a Young Adult Patient with a Diffuse Intrinsic Pontine Glioma.

Science.gov (United States)

Sison, Julian; Tran, Hung; Margol, Ashley; Tiwari, Nishant; Garcia, Karla M; Cotter, Jennifer; Kiehna, Erin; Olch, Arthur J; Wong, Kenneth

2017-08-18

Diffuse intrinsic pontine gliomas (DIPGs) are rare but devastating brain tumors that occur primarily in children. These gliomas have poor prognoses and present options focus on palliation of symptoms and prolongation of life. Here, we present a case of a 16-year-old female diagnosed with a DIPG whose age group has been mostly left out of discussions regarding psychosocial support options. This report is meant to start a conversation about the different support options available at our institution that have shown promising results in the literature for palliative care applications. These options can include camps for patients with brain tumors, psychological counseling, the Ronald McDonald House, and other psychosocial programs. Many of these programs can be tailored to meet the specific needs of adolescent and young adult (AYA) patients and will hopefully be integrated into a comprehensive palliative care regimen in future studies.

Metrics Evolution in an Energy Research and Development Program

International Nuclear Information System (INIS)

Dixon, Brent

2011-01-01

All technology programs progress through three phases: Discovery, Definition, and Deployment. The form and application of program metrics needs to evolve with each phase. During the discovery phase, the program determines what is achievable. A set of tools is needed to define program goals, to analyze credible technical options, and to ensure that the options are compatible and meet the program objectives. A metrics system that scores the potential performance of technical options is part of this system of tools, supporting screening of concepts and aiding in the overall definition of objectives. During the definition phase, the program defines what specifically is wanted. What is achievable is translated into specific systems and specific technical options are selected and optimized. A metrics system can help with the identification of options for optimization and the selection of the option for deployment. During the deployment phase, the program shows that the selected system works. Demonstration projects are established and classical systems engineering is employed. During this phase, the metrics communicate system performance. This paper discusses an approach to metrics evolution within the Department of Energy's Nuclear Fuel Cycle R and D Program, which is working to improve the sustainability of nuclear energy.

Utility Green-Pricing Programs: What Defines Success? (Topical Issues Brief); TOPICAL

International Nuclear Information System (INIS)

Swezey, B.; Bird, L.

2001-01-01

''Green pricing'' is an optional service through which customers can support a greater level of investment by their electric utility in renewable energy technologies. Electric utilities in 29 states are now implementing green-pricing programs. This report examines important elements of green-pricing programs, including the different types of programs offered, the premiums charged, customer response, and additional factors that experience indicates are key to the development of successful programs. The best-performing programs tend to share a number of common attributes related to product design, value creation, product pricing, and program implementation. The report ends with a list of ''best practices'' for utilities to follow when developing and implementing programs

Preliminary evaluation of crisis-relocation fallout-shelter options. Volume 1. Summary

International Nuclear Information System (INIS)

Santini, D.J.; Clinch, J.M.; Davis, F.H.; Hill, L.G.; Lynch, E.P.; Tanzman, E.A.; Wernette, D.R.

1982-03-01

This report, prepared for the Federal Emergency Management Agency (FEMA), presents a summary evaluation of various shelter options for use in the case where the President orders crisis relocation of the US urban population because of strong expectation of a nuclear war. The availability of livable shelter space at 40 ft 2 per person (congregate-care space) by state is evaluated. Options are evaluated for construction of fallout shelters allowing 10 ft 2 per person - such shelters are designed to provide 100% survival at projected levels of radioactive fallout. The authors find that the FEMA concept of upgrading existing buildings to act as fallout shelters can, in principle, provide adequate shelter throughout most of the US. Exceptions are noted and remedies proposed. The authors also find that, in terms of upgrading existing buildings to fallout shelter status, great benefits are possible by turning away from a standard national approach and adopting a more site-specific approach. Existing FEMA research provides a solid foundation for successful crisis relocation planning, but the program can be refined by making suitable modifications in its locational, engineering, and institutionally specific elements

Optimal Design of Measurement Programs for the Parameter Identification of Dynamic Systems

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Sørensen, John Dalsgaard; Brincker, Rune

The design of measurement programs devoted to parameter identification of structural dynamic systems is considered. The design problem is formulated as an optimization problem to minimize the total expected cost that is the cost of failure and the cost of the measurement program. All...... the calculations are based on a priori knowledge and engineering judgement. One of the contribution of the approach is that the optimal number of sensors can be estimated. This is shown in a numerical example where the proposed approach is demonstrated. The example is concerned with design of a measurement program...

Optimal Design of Measurement Programs for the Parameter Identification of Dynamic Systems

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Sørensen, John Dalsgaard; Brincker, Rune

The design of a measured program devoted to parameter identification of structural dynamic systems is considered, the design problem is formulated as an optimization problem due to minimize the total expected cost of the measurement program. All the calculations are based on a priori knowledge...... and engineering judgement. One of the contribution of the approach is that the optimal nmber of sensors can be estimated. This is sown in an numerical example where the proposed approach is demonstrated. The example is concerned with design of a measurement program for estimating the modal damping parameters...

Design Program in Graphic User Interface Environment for Automobile ER Devices

Science.gov (United States)

Lim, S. C.; Park, J. S.; Sohn, J. W.; Choi, S. B.

This work presents a design and analysis program for vehicle devices utilizing an electrorheological (ER) fluid. The program is operated in graphic user interface (GUI) environment and the initial window is consisted of four subprogram modules which are related to ER shock absorber, ER seat damper, ER engine mount, and ER anti-lock brake system (ABS), respectively. In order to execute each module, both material properties and design parameters are to be chosen by the user. Then, the output display window shows the field-dependent performance characteristics to be considered as design criteria. In addition, control performances of the vehicle system equipped with ER devices are displayed in time and frequency domain. In order to demonstrate the effectiveness of the proposed program, ER shock absorber and ER ABS are designed and manufactured and their performance characteristics are evaluated.

Program Design Report of the CNC Machine Tool(II)

International Nuclear Information System (INIS)

Kim, Jong Kiun; Youm, K. U.; Kim, K. S.; Lee, I. B.; Yoon, K. B.; Lee, C. K.; Youm, J. H.

2007-06-01

The application of CNC machine tool being widely expanded according to variety of machine work method and rapid promotion of machine tool, cutting tool, for high speed efficient machine work. In order to conduct of the project of manufacture and maintenance of laboratory equipment, production design and machine work technology are continually developed, especially the application of CNC machine tool is very important for the improvement of productivity, quality and clearing up a manpower shortage. We publish technical report which it includes CNC machine tool program and drawing, it contributes to the systematic development of CNC program design and machine work technology

Program Design Report of the CNC Machine Tool(II)

Energy Technology Data Exchange (ETDEWEB)

Kim, Jong Kiun; Youm, K. U.; Kim, K. S.; Lee, I. B.; Yoon, K. B.; Lee, C. K.; Youm, J. H

2007-06-15

The application of CNC machine tool being widely expanded according to variety of machine work method and rapid promotion of machine tool, cutting tool, for high speed efficient machine work. In order to conduct of the project of manufacture and maintenance of laboratory equipment, production design and machine work technology are continually developed, especially the application of CNC machine tool is very important for the improvement of productivity, quality and clearing up a manpower shortage. We publish technical report which it includes CNC machine tool program and drawing, it contributes to the systematic development of CNC program design and machine work technology.

Program Design Report of the CNC Machine Tool(III)

International Nuclear Information System (INIS)

Kim, Jong Kiun; Youm, K. U.; Kim, K. S.; Lee, I. B.; Yoon, K. B.; Lee, C. K.; Youm, J. H.

2008-08-01

The application of CNC machine tool being widely expanded according to variety of machine work method and rapid promotion of machine tool, cutting tool, for high speed efficient machine work. In order to conduct of the project of manufacture and maintenance of laboratory equipment, production design and machine work technology are continually developed, especially the application of CNC machine tool is very important for the improvement of productivity, quality and clearing up a manpower shortage. We publish technical report which it includes CNC machine tool program and drawing, it contributes to the systematic development of CNC program design and machine work technology

Program Design Report of the CNC Machine Tool (I)

International Nuclear Information System (INIS)

Kim, Jong Kiun; Youm, K. U.; Kim, K. S.

2006-08-01

The application of CNC machine tool being widely expanded according to variety of machine work method and rapid promotion of machine tool, cutting tool, for high speed efficient machine work. In order to conduct of the project of manufacture and maintenance of laboratory equipment, production design and machine work technology are continually developed, especially the application of CNC machine tool is very important for the improvement of productivity, quality and clearing up a manpower shortage. We publish technical report which it includes CNC machine tool program and drawing, it contributes to the systematic development of CNC program design and machine work technology

Program Design Report of the CNC Machine Tool(IV)

International Nuclear Information System (INIS)

Youm, Ki Un; Lee, I. B.; Youm, J. H.

2009-09-01

The application of CNC machine tool being widely expanded according to variety of machine work method and rapid promotion of machine tool, cutting tool, for high speed efficient machine work. In order to conduct of the project of manufacture and maintenance of laboratory equipment, production design and machine work technology are continually developed, especially the application of CNC machine tool is very important for the improvement of productivity, quality and clearing up a manpower shortage. We publish technical report which it includes CNC machine tool program and drawing, it contributes to the systematic development of CNC program design and machine work technology

Design of training programs for a positive youth development program: Project P.A.T.H.S. in Hong Kong.

Science.gov (United States)

Shek, Daniel T L; Chak, Yammy L Y

2010-01-01

To facilitate the implementation of the Secondary 1 to Secondary 3 program of the Project P.A.T.H.S. in Hong Kong, systematic training programs are designed for the potential program implementers. The rationales, objectives and design of the Secondary 1 to Secondary 3 training programs are outlined in this paper. The training programs cover theories of adolescent development, positive youth development, background and curricula of the Project P.A.T.H.S., factors affecting program implementation quality and evaluation of the project. Besides introducing the curriculum units, the training programs also focus on nature of learning and related theories (particularly experiential learning), teaching methods and instructional techniques, motivating students, and classroom management.

Radwaste assessment program for nuclear station modifications by design engineering

International Nuclear Information System (INIS)

Eble, R.G.

1988-01-01

Radwaste burial for Duke Power Company's (DPC's) seven nuclear units has become a complicated and costly process. Burial costs are based on overall volume, surcharges for radioactivity content and weight of containers, truck and cask rental, driver fees, and state fees and taxes. Frequently, radwaste costs can be as high as $500 per drum. Additionally, DPC is limited on the total burial space allocated for each plant each year. The thrust of this program is to reduce radwaste volumes needing burial at either Barnwell, South Carolina, or Richland, Washington. A limited number of options are available at our sites: (a) minimization of radwaste volume production, (b) segregation of contamination and noncontaminated trash, (c) decontamination of small hardware, (d) volume reduction of compatible trash, (e) incineration of combustible trash (available at Oconee in near future), and (f) burial of below-regulatory-concern very low level waste on site. Frequently, costs can be reduced by contracting services outside the company, i.e., supercompaction, decontamination, etc. Information about radwaste volumes, activities, and weight, however, must be provided to the nuclear production department (NPD) radwaste group early in the nuclear station modification (NSM) process to determine the most cost-effective method of processing radwaste. In addition, NSM radwaste costs are needed for the NPD NSM project budget. Due to the advanced planning scope of this budget, NSM construction costs must be estimated during the design-phase proposal

Mouse-tracking evidence for parallel anticipatory option evaluation.

Science.gov (United States)

Cranford, Edward A; Moss, Jarrod

2017-12-23

In fast-paced, dynamic tasks, the ability to anticipate the future outcome of a sequence of events is crucial to quickly selecting an appropriate course of action among multiple alternative options. There are two classes of theories that describe how anticipation occurs. Serial theories assume options are generated and evaluated one at a time, in order of quality, whereas parallel theories assume simultaneous generation and evaluation. The present research examined the option evaluation process during a task designed to be analogous to prior anticipation tasks, but within the domain of narrative text comprehension. Prior research has relied on indirect, off-line measurement of the option evaluation process during anticipation tasks. Because the movement of the hand can provide a window into underlying cognitive processes, online metrics such as continuous mouse tracking provide more fine-grained measurements of cognitive processing as it occurs in real time. In this study, participants listened to three-sentence stories and predicted the protagonists' final action by moving a mouse toward one of three possible options. Each story was presented with either one (control condition) or two (distractor condition) plausible ending options. Results seem most consistent with a parallel option evaluation process because initial mouse trajectories deviated further from the best option in the distractor condition compared to the control condition. It is difficult to completely rule out all possible serial processing accounts, although the results do place constraints on the time frame in which a serial processing explanation must operate.

Large coil program support structure conceptual design

International Nuclear Information System (INIS)

Litherland, P.S.

1977-01-01

The purpose of the Large Coil Program (LCP) is to perform tests on both pool boiling and force cooled superconducting toroidal field coils. The tests will attempt to approximate conditions anticipated in an ignition tokamak. The test requirements resulted in a coil support design which accommodates up to six (6) test coils and is mounted to a structure capable of resisting coil interactions. The steps leading to the present LCP coil support structure design, details on selected structural components, and the basic assembly sequence are discussed

Seca Coal-Based Systems Program

International Nuclear Information System (INIS)

Alinger, Matthew

2008-01-01

This report summarizes the progress made during the August 1, 2006 - May 31, 2008 award period under Cooperative Agreement DE-FC26-05NT42614 for the U. S. Department of Energy/National Energy Technology Laboratory (USDOE/NETL) entitled 'SECA Coal Based Systems'. The initial overall objective of this program was to design, develop, and demonstrate multi-MW integrated gasification fuel cell (IGFC) power plants with >50% overall efficiency from coal (HHV) to AC power. The focus of the program was to develop low-cost, high performance, modular solid oxide fuel cell (SOFC) technology to support coal gas IGFC power systems. After a detailed GE internal review of the SOFC technology, the program was de-scoped at GE's request. The primary objective of this program was then focused on developing a performance degradation mitigation path for high performing, cost-effective solid oxide fuel cells (SOFCs). There were two initial major objectives in this program. These were: (1) Develop and optimize a design of a >100 MWe integrated gasification fuel cell (IGFC) power plant; (2) Resolve identified barrier issues concerning the long-term economic performance of SOFC. The program focused on designing and cost estimating the IGFC system and resolving technical and economic barrier issues relating to SOFC. In doing so, manufacturing options for SOFC cells were evaluated, options for constructing stacks based upon various cell configurations identified, and key performance characteristics were identified. Key factors affecting SOFC performance degradation for cells in contact with metallic interconnects were be studied and a fundamental understanding of associated mechanisms was developed using a fixed materials set. Experiments and modeling were carried out to identify key processes/steps affecting cell performance degradation under SOFC operating conditions. Interfacial microstructural and elemental changes were characterized, and their relationships to observed degradation

Utility Green-Pricing Programs: What Defines Success? (Topical Issues Brief)

Energy Technology Data Exchange (ETDEWEB)

Swezey, B.; Bird, L.

2001-09-13

''Green pricing'' is an optional service through which customers can support a greater level of investment by their electric utility in renewable energy technologies. Electric utilities in 29 states are now implementing green-pricing programs. This report examines important elements of green-pricing programs, including the different types of programs offered, the premiums charged, customer response, and additional factors that experience indicates are key to the development of successful programs. The best-performing programs tend to share a number of common attributes related to product design, value creation, product pricing, and program implementation. The report ends with a list of ''best practices'' for utilities to follow when developing and implementing programs.

The synchrotron option for a multi-megawatt proton driver

CERN Document Server

Prior, C R

2006-01-01

Of the three main options for a proton driver for a neutrino facility, synchrotron-based designs feature in proposals from J-PARC, Brookhaven and the Rutherford Appleton Laboratory. There are also synchrotron and linac options being considered in parallel at Fermilab. The Japanese machine has been developed from initial plans for a 3 GeV neutron source into a multi-purpose facility, with the addition of a 50 GeV proton synchrotron in a phased programme of construction. Brookhaven's ideas are based on upgrading the AGS, first to 1 MW and then to 4 MW. Fermilab is looking for a design to bypass the bottleneck that is the existing booster. At RAL, several designs have emerged, including one specifically based on upgrading the ISIS spallation neutron source into a possible dual neutron- neutrino facility.

Negotiating and Designing Public Space. Experiences with a new M.Sc. in Urban Design Program in Hong Kong

Directory of Open Access Journals (Sweden)

Hendrik Tieben

2013-05-01

Full Text Available This contribution reflects on first experiences made with a newly launched Master of Science in Urban Design program at the Chinese University of Hong Kong. As an important part of this program, students have to develop their design proposal in response to feedback of different stakeholders and community members. Thus the program responds to the growing aspiration of Hong Kong’s citizens to shape the urban development of their city and a lack of a meaningful participation process in the region. With its high density, protected country parks, efficient public transport and large scale housing program, generally, Hong Kong offers important lessons for contemporary urbanism. However, since the end of the British colonial rule and in face of increasing property prices, pollution and the disappearance of local heritage, intensive debates started about the regions future. Another central point of the recent discussion in Hong Kong – and key theme of the new urban design program - is the demand for the rights and qualities of public space. The paper presents the set-up of the design studio, which was closely linked to a course on “urban processes”. During the semester, students had to organize community forums and street exhibitions in a specific district, invite stakeholders and residents and discuss with them their ideas. Their projects, then, had to respond on the various feedbacks and integrate them in their design and policy proposals. The text reflects on the student projects and the lessons learned in the process. It addresses general questions such as the challenges in communicating with a diverse community (e.g. language barriers and culturally different ideas of public space. It addresses the question of the intended and unintended effects of a participatory design studio in the community, and possible follow-ups. And it reflects on the general role of design and designers in shaping community spaces.

Exotic Options: a Chooser Option and its Pricing

Directory of Open Access Journals (Sweden)

Raimonda Martinkutė-Kaulienė

2012-12-01

Full Text Available Financial instruments traded in the markets and investors’ situation in such markets are getting more and more complex. This leads to more complex derivative structures used for hedging that are harder to analyze and which risk is harder managed. Because of the complexity of these instruments, the basic characteristics of many exotic options may sometimes be not clearly understood. Most scientific studies have been focused on developing models for pricing various types of exotic options, but it is important to study their unique characteristics and to understand them correctly in order to use them in proper market situations. The paper examines main aspects of options, emphasizing the variety of exotic options and their place in financial markets and risk management process. As the exact valuation of exotic options is quite difficult, the article deals with the theoretical and practical aspects of pricing of chooser options that suggest a broad range of usage and application in different market conditions. The calculations made in the article showed that the price of the chooser is closely correlated with the choice time and low correlated with its strike price. So the first mentioned factor should be taken into consideration when making appropriate hedging and investing decisions.

Real option valuation of power transmission investments by stochastic simulation

International Nuclear Information System (INIS)

Pringles, Rolando; Olsina, Fernando; Garcés, Francisco

2015-01-01

Network expansions in power markets usually lead to investment decisions subject to substantial irreversibility and uncertainty. Hence, investors need valuing the flexibility to change decisions as uncertainty unfolds progressively. Real option analysis is an advanced valuation technique that enables planners to take advantage of market opportunities while preventing or mitigating losses if future conditions evolve unfavorably. In the past, many approaches for valuing real options have been developed. However, applying these methods to value transmission projects is often inappropriate as revenue cash flows are path-dependent and affected by a myriad of uncertain variables. In this work, a valuation technique based on stochastic simulation and recursive dynamic programming, called Least-Square Monte Carlo, is applied to properly value the deferral option in a transmission investment. The effect of option's maturity, the initial outlay and the capital cost upon the value of the postponement option is investigated. Finally, sensitivity analysis determines optimal decision regions to execute, postpone or reject the investment projects. - Highlights: • A modern investment appraisal method is applied to value power transmission projects. • The value of the option to postpone decision to invest in transmission projects is assessed. • Simulation methods are best suited for valuing real options in transmission investments

Education Model Program on Water-Energy Research: A New STEM Graduate Program from Development through Evaluation

Science.gov (United States)

McCay, D.; Fiorenza, P.; Lautz, L.

2017-12-01

More than half of Ph.D. scientists and engineers find employment in non-academic sectors. Recognizing the range of career options for graduate degree holders and the need to align graduate education with the expectations of prospective employers, the National Science Foundation (NSF) created the NSF Research Traineeship (NRT) program. To date, over 100 NRT programs have been funded. As these programs are implemented, it is important to assess their progress, successes, and challenges. This presentation describes the ongoing evaluation of one NRT program, "Education Model Program on Water-Energy Research" (or EMPOWER) at Syracuse University. Through seminars, mini-grants, professional development activities, field courses, internship opportunities, and coursework, EMPOWER's goal is to equip students with the skills needed for the range of career options in water and energy. In collaboration with an external evaluator, EMPOWER is examining the fidelity of the program to proposed goals, providing feedback to inform project improvement (formative assessment) and assessing the effectiveness of achieving program goals (summative assessment). Using a convergent parallel mixed method design, qualitative and quantitative data were collected to develop a full assessment of the first year of the program. Evaluation findings have resulted in several positive changes to the program. For example, EMPOWER students perceive themselves to have high technical skills, but the data show that the students do not believe that they have a strong professional network. Based on those findings, EMPOWER offered several professional development events focused on building one's professional network. Preliminary findings have enabled the EMPOWER leadership team to make informed decisions about the ways the program elements can be redesigned to better meet student needs, about how to the make the program more effective, and determine the program elements that may be sustained beyond the funding

Implementation Options for the PROPEL Electrodynamic Tether Demonstration Mission

Science.gov (United States)

Bilen, Sven G.; Johnson, C. Les; Gilchrist, Brian E.; Hoyt, Robert P.; Elder, Craig H.; Fuhrhop, Keith P.; Scadera, Michael; Stone, Nobie

2014-01-01

The PROPEL ("Propulsion using Electrodynamics") flight demonstration mission concept will demonstrate the use of an electrodynamic tether (EDT) for generating thrust, which will allow the propulsion system to overcome the limitations of the rocket equation. The mission concept has been developed by a team of government, industry, and academia partners led by NASA Marshall Space Flight Center (MSFC). PROPEL is being designed for versatility of the EDT system with multiple end users in mind and to be flexible with respect to platform. Previously, we reported on a comprehensive mission design for PROPEL with a mission duration of six months or longer with multiple mission goals including demonstration of significant boost, deboost, inclination change, and drag make-up activities. To explore a range of possible configurations, primarily driven by cost considerations, other mission concept designs have been pursued. In partnership with the NASA's Office of Chief Technologist (OCT) Game Changing Program, NASA MSFC Leadership, and the MSFC Advanced Concepts Office, a mission concept design was developed for a near-term EDT propulsion flight validation mission. The Electrodynamic Tether Propulsion Study (ETPS) defined an EDT propulsion system capable of very large delta-V for use on future missions developed by NASA, DoD, and commercial customers. To demonstrate the feasibility of an ETPS, the study focused on a space demonstration mission concept design with configuration of a pair of tethered satellite busses, one of which is the Japanese H-II Transfer Vehicle (HTV). The HTV would fly its standard ISS resupply mission. When resupply mission is complete, the ISS reconfigures and releases the HTV to perform the EDT experiment at safe orbital altitudes below the ISS. Though the focus of this particular mission concept design addresses a scenario involving the HTV or a similar vehicle, the propulsion system's capability is relevant to a number of applications, as noted above

Interim Policy Options for Commercialization of Solar Heating and Cooling Systems.

Science.gov (United States)

Bezdek, Roger

This interim report reviews the major incentive policy options available to accelerate market penetration of solar heating and cooling (SHAC) systems. Feasible policy options designed to overcome existing barriers to commercial acceptance and market penetration are identified and evaluated. The report is divided into seven sections, each dealing…

A Competence-Based Curriculum Design for Entrepreneurship Study Program

Directory of Open Access Journals (Sweden)

Priska J.R. Siagian

2011-08-01

Full Text Available Indonesia is affected by global crisis. Increasing the number of entrepreneurs is one of many solutions to increase the economic growth in Indonesia. The number of entrepreneurs in Indonesia to leverage the economic growth is still limited. Entrepreneurs can be prepared through an Entrepreneurship Study Program. Entrepreneurship Study Program attempts to create qualified entrepreneurs who have relevant competences. In order to create a qualified entrepreneurs, the Entrepreneurial Studies Program requires a competency-based curriculum that will support the educational process and provide all the necessary to become future entrepreneurs who can survive through a global challenge. This research aims to design a competence-based curriculum for entrepreneurial study and uses Quality Function Deployment (QFD as the major tool to design the competence-based curriculum. From the QFD process, this research finds core and elective courses for the Entrepreneurship Study Program. The result shows the competences covered by the courses and sequence, credits, and teaching methods for each course. The competences prepared the potential entrepreneurs can be achieved through specific courses which can be acquired within 8 semesters.

Western Option - Disarmament of Russian Weapon Plutonium

International Nuclear Information System (INIS)

Tveiten, B.; Petroll, M.R.

2002-01-01

The Western Option concept describes an approach to the conversion of weapon-grade plutonium from Russian nuclear warheads under the special aspects of meeting the criteria of irreversible utilization. Putting this concept of plutonium conversion into non-weapon-grade material into effect would make a major contribution to improving security worldwide. This study is based on an agreement between the Russian Federation and the United States of America concluded in September 2000. It provides for the conversion of 34 t of weapon-grade plutonium in each of the two states. This goal is also supported by other G8 countries. While the United States performs its part of the agreement under its sole national responsibility, the Russian program needs financial support by Western states. Expert groups have pointed out several options as a so-called basic scenario. The funds of approx. US Dollar 2 billion required to put them into effect have not so far been raised. The Western Option approach described in this contribution combines results of the basic scenario with other existing experience and with technical solutions available for plutonium conversion. One of the attractions of the Western Option lies in its financial advantages, which are estimated to amount to approx. US Dollar 1 billion. (orig.) [de

MPprimer: a program for reliable multiplex PCR primer design

Directory of Open Access Journals (Sweden)

Wang Xiaolei

2010-03-01

Full Text Available Abstract Background Multiplex PCR, defined as the simultaneous amplification of multiple regions of a DNA template or multiple DNA templates using more than one primer set (comprising a forward primer and a reverse primer in one tube, has been widely used in diagnostic applications of clinical and environmental microbiology studies. However, primer design for multiplex PCR is still a challenging problem and several factors need to be considered. These problems include mis-priming due to nonspecific binding to non-target DNA templates, primer dimerization, and the inability to separate and purify DNA amplicons with similar electrophoretic mobility. Results A program named MPprimer was developed to help users for reliable multiplex PCR primer design. It employs the widely used primer design program Primer3 and the primer specificity evaluation program MFEprimer to design and evaluate the candidate primers based on genomic or transcript DNA database, followed by careful examination to avoid primer dimerization. The graph-expanding algorithm derived from the greedy algorithm was used to determine the optimal primer set combinations (PSCs for multiplex PCR assay. In addition, MPprimer provides a virtual electrophotogram to help users choose the best PSC. The experimental validation from 2× to 5× plex PCR demonstrates the reliability of MPprimer. As another example, MPprimer is able to design the multiplex PCR primers for DMD (dystrophin gene which caused Duchenne Muscular Dystrophy, which has 79 exons, for 20×, 20×, 20×, 14×, and 5× plex PCR reactions in five tubes to detect underlying exon deletions. Conclusions MPprimer is a valuable tool for designing specific, non-dimerizing primer set combinations with constrained amplicons size for multiplex PCR assays.

The Gel Generator option

International Nuclear Information System (INIS)

Boyd, R.E.

1999-01-01

The development of a national policy for guaranteeing an ample supply of 99m Tc to nuclear medicine, involves issues which go beyond the means by which radioactivation is achieved. Indeed, in such an exercise the pragmatic dictates of business and the sensitivities of politics must also be taken into account. Furthermore where a preference towards the nuclear reactor or the potential of cyclotrons is being questioned, the debate is incomplete if the only options that are considered are the fission-based 99 Mo generator versus the direct cyclotron production of 99m Tc. There is a third option (also neutron γ-based), an alternative to the fission 99 Mo generator, which ought not be overlooked. The application of low specific activity (n,γ) 99 Mo to a new type of generator, the Gel Generator, has been the focus of much research, particularly in Australia and more recently in China. After the initial concept had been established in the laboratory, the Australian researchers then undertook a comprehensive program of tests on the Gel Generator to assess its potential, either in the clinical laboratory or the centralised radiopharmacy, for supplying 99m Tc suitable for nuclear medicine. The outcome of this program was a clear indication that the Gel Generator innovation had the capability to provide both technical and economic advantages to the nuclear medicine industry. These advantages are described. Since that time the Gel Generator has been selected for routine use in China where it now satisfies more than 30% of the 99m Tc demand. (author)

The Engineering Compliance Program development process and its role in design

International Nuclear Information System (INIS)

1997-12-01

This paper presents an overview of the Engineering Compliance Program (ECP) development process and its role in design. The ECP is a formal program to assess Nuclear Regulatory Commission (NRC) regulatory guidance in terms of precedence, industry experience documents, and codes and standards to determine their applicability to Mined Geologic Disposal System (MGDS) design. These determinations are documented in ECP Guidance Packages for MGDS Structures, Systems and Components (SSCs). This ensures that the license application appropriately reflects the MGDS design and facilitates NRC acceptance and compliance review

Design options for automotive batteries in advanced car electrical systems

Science.gov (United States)

Peters, K.

The need to reduce fuel consumption, minimize emissions, and improve levels of safety, comfort and reliability is expected to result in a much higher demand for electric power in cars within the next 5 years. Forecasts vary, but a fourfold increase in starting power to 20 kW is possible, particularly if automatic stop/start features are adopted to significantly reduce fuel consumption and exhaust emissions. Increases in the low-rate energy demand are also forecast, but the use of larger alternators may avoid unacceptable high battery weights. It is also suggested from operational models that the battery will be cycled more deeply. In examining possible designs, the beneficial features of valve-regulated lead-acid batteries made with compressed absorbent separators are apparent. Several of their attributes are considered. They offer higher specific power, improved cycling capability and greater vibration resistance, as well as more flexibility in packaging and installation. Optional circuits considered for dual-voltage supplies are separate batteries for engine starting (36 V) and low-power duties (12 V), and a universal battery (36 V) coupled to a d.c.-d.c. converter for a 12-V equipment. Battery designs, which can be made on commercially available equipment with similar manufacturing costs (per W h and per W) to current products, are discussed. The 36-V battery, made with 0.7 mm thick plates, in the dual-battery system weighs 18.5 kg and has a cold-cranking amp (CCA) rating of 790 A at -18°C to 21.6 V (1080 W kg -1 at a mean voltage of 25.4 V). The associated, cycleable 12-V battery, provides 1.5 kW h and weighs 24.6 kg. Thus, the combined battery weight is 43.1 kg. The single universal battery, with cycling capability, weighs 45.4 kg, has a CCA rating of 810 A (441 W kg -1 at a mean voltage of 24.7 V), and when connected to the d.c.-d.c. converter at 75% efficiency provides a low-power capacity of 1.5 kW h.

A Program for Introducing Information Literacy to Commercial Art and Design Students

Directory of Open Access Journals (Sweden)

David A. Walczak

2010-03-01

Full Text Available This paper describes the process of developing and implementing a comprehensive, school-wide, and sustainable information literacy program at a commercial art and design school. The program requires that information literacy student learning outcomes be included in specific General Education and art and design courses across the curriculum. The results of this multi-year effort indicate that while the program is sound, teaching information literacy is an on-going effort requiring much more training of faculty and students. Best practices in information literacy in library science and art and design literature are reviewed

Insert earphone calibration for hear-through options

DEFF Research Database (Denmark)

Hoffmann, Pablo F.; Christensen, Flemming; Hammershøi, Dorte

2013-01-01

A hear-through option in earphones exists when the earphone has a microphone mounted on the outside of the earphone thus allowing the user to hear the surroundings - or not. Although routing the microphone signal to the earphone driver is relatively straightforward, the physical presence of the e......A hear-through option in earphones exists when the earphone has a microphone mounted on the outside of the earphone thus allowing the user to hear the surroundings - or not. Although routing the microphone signal to the earphone driver is relatively straightforward, the physical presence...... of the earphone will modify the natural acoustics of the external ear, and some form of compensation is required to make the microphone-earphone combination acoustically transparent. Here we derive a general expression for the design target response of insert earphones with hear-through options emphasizing...

Designing Cross-Cultural Orientation Programs for Business.

Science.gov (United States)

Ogden, John D.

A 1-day orientation workshop for business clients from other cultures is described. Factors in program design that relate to the specific cultural group addressed are discussed, and include such considerations as culture-specific versus culture-general content, professional focus, and the learning style to which the participants are accustomed.…

Development of design program for small-sized gas absorption chiller/heaters

Energy Technology Data Exchange (ETDEWEB)

Yoon, J.I.; Kwon, O.K.; Moon, C.K. [Pukyong National University, Pusan (Korea); Yang, Y.M.; Kim, H.Y. [R and D Center, Korea Gas Corporation, Ansan (Korea)

1999-10-01

Analysis of basic data is performed for development of small size water-cooled household absorption chiller/heater using non CFC refrigerant, analytic simulation program of air cooling performance is developed that system has 1.5-10RT of air cooling performance, we perform cycle analysis and numerical simulation. We develope a performance analysis of simulation program to perform a basic design for 1.5-10RT apparatus of small size system of development model in gas driven double effect absorption chiller/heater. The system working condition and operation limit condition is decided from the existing data which is analyzed and the conference with KOGAS. After the basic input variable and regular condition is established for heat cycle analysis, the simulation algorithm is set up and performance simulation program is coded according to the organized algorithm. The basic design of optimum system is completed from parametric study using developed simulation program and establishing the design variable range of developing object model. 20 refs., 30 figs., 9 tabs.

Shader programming for computational arts and design: A comparison between creative coding frameworks

OpenAIRE

Gomez, Andres Felipe; Colubri, Andres; Charalambos, Jean Pierre

2016-01-01

We describe an Application Program Interface (API) that facilitates the use of GLSL shaders in computational design, interactive arts, and data visualization. This API was first introduced in the version 2.0 of Processing, a programming language and environment widely used for teaching and production in the context of media arts and design, and has been recently completed in the 3.0 release. It aims to incorporate low-level shading programming into code-based design, by int...

Early hydrogen water chemistry project review, improvement opportunities and conceptural design options at Exelon boiling water reactors

International Nuclear Information System (INIS)

Garcia, Susan E.; Odell, Andrew D.; Giannelli, Joseph F.

2012-09-01

Intergranular Stress Corrosion Cracking (IGSCC) and its impacts have been a major concern to the BWR fleet since the mid-70's. Several alternative strategies have been employed to reduce the negative impacts, however, the newest being Early Hydrogen Water Chemistry (EHWC). The Electric Power Research Institute (EPRI) and the BWRVIP (Vessel Internals Project) has strongly supported the development of EHWC, including laboratory testing and a demonstration program that was performed at Peach Bottom Atomic Power Station in October 2011. This paper will review the impacts of a 'Special Test Program' on a BWR plant including: Project management findings; technical reviews and documents required to support such a demonstration program; temporary equipment design, installation and testing; keeping the demonstration progressing along with the plant return from a refuel outage; and lessons learned that can be applied to EHWC implementation during future start-ups. Details will be compared between various Exelon BWRs in support of conceptual designs for EHWC systems and operation. Some comparisons on operational impacts will be provided between various types of BWR plants with differing 'Balance of Plant' designs. (authors)

Nontraditional Degree Options for Nurses: A Model Program

Science.gov (United States)

Walston, Sydney C.

1978-01-01

The Institute for Personal and Career Development of Central Michigan University offers external degree programs for adult learners using nontraditional study. The competency-based programs described include credit given for the educational background and relevant career-life experiences of registered nurses in Michigan. (Author/LBH)

Australian Asian Options

OpenAIRE

Manuel Moreno; Javier F. Navas

2003-01-01

We study European options on the ratio of the stock price to its average and viceversa. Some of these options are traded in the Australian Stock Exchange since 1992, thus we call them Australian Asian options. For geometric averages, we obtain closed-form expressions for option prices. For arithmetic means, we use different approximations that produce very similar results.

Demand-side management pricing options in electric utilities

International Nuclear Information System (INIS)

Sardana, P.; Herman, P.

1990-01-01

In 1989 Ontario Hydro implemented optional time-of-use (TOU) rates at the wholesale level for all municipal utilities in the province. At the same time, mandatory TOU rates were implemented for large users (customers with loads in excess of 5 MW) served by municipal utilities and Ontario Hydro's direct customers. To fully explore the potential of rate structures as demand-side management (DSM) tools, Ontario Hydro retained a consulting firm to carry out a survey of innovative rate structures in other jurisdications. The survey was intended to identify: the status quo of rate structures in other jurisdictions that were designed specifically to encourage DSM; a profile of the cost basis of the rate structures, for example whether traditional embedded cost of service analyses or contentious methods such as marginal cost pricing were used; whether innovative rates have been successful, and customer reactions and attitudes; and how innovative rates fit into the overall strategy of the utilities. It was found that TOU, interruptible and end-use targeted rates are the rate structures of choice for many utilities. Most are concerned with deferring capacity, reducing peak demand, and shifting load out of peak periods. Most utilities report success with their programs and satisfaction with the present form of the programs. 5 tabs

Program design of data acquisition in Windows

International Nuclear Information System (INIS)

Cai Jianxin; Yan Huawen

2004-01-01

Several methods for the design of data acquisition program based on Microsoft Windows are introduced. Then their respective advantages and disadvantages are totally analyzed. At the same time, the data acquisition modes applicable to each method are also pointed out. It is convenient for data acquisition programmers to develop data acquisition systems. (authors)

Near-term hybrid vehicle program, phase 1. Appendix B: Design trade-off studies report. Volume 3: Computer program listings

Science.gov (United States)

1979-01-01

A description and listing is presented of two computer programs: Hybrid Vehicle Design Program (HYVELD) and Hybrid Vehicle Simulation Program (HYVEC). Both of the programs are modifications and extensions of similar programs developed as part of the Electric and Hybrid Vehicle System Research and Development Project.

Building EOS capability for Malaysia - the options

Science.gov (United States)

Subari, M. D.; Hassan, A.

2014-06-01

Earth observation satellite (EOS) is currently a major tool to monitor earth dynamics and increase human understanding of earth surface process. Since the early 80s, Malaysia has been using EOS images for various applications, such as weather forecasting, land use mapping, agriculture, environment monitoring and others. Until now, all EOS images were obtained from foreign satellite systems. Realising on the strategic need of having its own capability, Malaysia embarked into EOS development programs in the early 90s. Starting with TiungSAT-1, a micro-satellite carrying small camera, then followed by RazakSAT, a small satellite carrying 2.5 m panchromatic (PAN) medium-aperture-camera, the current satellite program development, the RazakSAT-2, designed to carry a 1.0 m high resolution PAN and 4.0m multi-spectral camera, would become a strategic initiative of the government in developing and accelerating the nation's capability in the area of satellite technology and its application. Would this effort continue until all needs of the remote sensing community being fulfilled by its own EOS? This paper will analyze the intention of the Malaysian government through its National Space Policy and other related policy documents, and proposes some policy options on this. Key factors to be considered are specific data need of the EOS community, data availability and the more subjective political motivations such as national pride.

Evaluability Assessment Thesis and Dissertation Studies in Graduate Professional Degree Programs

Science.gov (United States)

Walser, Tamara M.; Trevisan, Michael S.

2016-01-01

Evaluability assessment (EA) has potential as a design option for thesis and dissertation studies, serving as a practical training experience for both technical and nontechnical evaluation skills. Based on a content review of a sample of EA theses and dissertations from graduate professional degree programs, the authors of this article found that…

75 FR 19439 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Proposed...

Science.gov (United States)

2010-04-14

... Modified by Amendment No. 1 Thereto, To List and Trade CBOE Gold ETF Volatility Index Options April 7, 2010... for the listing and trading of options that overlie the CBOE Gold ETF Volatility Index (``GVZ... options on the CBOE Gold ETF Volatility Index (``GVZ''). Index Design and Calculation: The calculation of...

Technology programs in support of advanced light water reactors

International Nuclear Information System (INIS)

1990-03-01

Design for Constructability's overall purpose was to identify and address changes in the nuclear industry to restore nuclear energy as an attractive option for new generating capacity. The program stove to meet the following goals related to the future construction of nuclear power plants: reduced costs; assurance of improved quality; and shortened construction schedules. This is Volume 1 of three volumes

Welfare Reform: Tribal TANF Allows Flexibility To Tailor Programs, but Conditions on Reservations Make It Difficult To Move Recipients into Jobs. Report to Congressional Requesters.

Science.gov (United States)

General Accounting Office, Washington, DC.

The 1996 Personal Responsibility and Work Opportunity Reconciliation Act gave American Indian and Alaska Native tribes the option to administer Temporary Assistance for Needy Families (TANF) programs either alone or in a tribal consortium. The law also granted tribal TANF programs more flexibility in program design than it gave to state programs.…

Real Options in Capital Budgeting. Pricing the Option to Delay and the Option to Abandon a Project

Directory of Open Access Journals (Sweden)

Nicoleta Vintila

2007-07-01

Full Text Available Traditional discounted cash-flows method for assessing projects assumes that investment decision is an irreversible one, which is not correct. Managers can and must reconsider their initial decision as the new information arises during the project life. This is managerial flexibility and it creates strategic value for a project, only if management takes advantage of the opportunities associated with an analyzed project. Real options represent a new approach in capital budgeting, using the theory of pricing financial options for investments in real assets. In this paper, we emphasize the characteristics and valuation methodologies of real options. The objective in the last section is pricing the option to delay and the option to abandon a project in construction materials field.

IPAD applications to the design, analysis, and/or machining of aerospace structures. [Integrated Program for Aerospace-vehicle Design

Science.gov (United States)

Blackburn, C. L.; Dovi, A. R.; Kurtze, W. L.; Storaasli, O. O.

1981-01-01

A computer software system for the processing and integration of engineering data and programs, called IPAD (Integrated Programs for Aerospace-Vehicle Design), is described. The ability of the system to relieve the engineer of the mundane task of input data preparation is demonstrated by the application of a prototype system to the design, analysis, and/or machining of three simple structures. Future work to further enhance the system's automated data handling and ability to handle larger and more varied design problems are also presented.

Hydride heat pump. Volume I. Users manual for HYCSOS system design program. [HYCSOS code

Energy Technology Data Exchange (ETDEWEB)

Gorman, R.; Moritz, P.

1978-05-01

A method for the design and costing of a metal hydride heat pump for residential use and a computer program, HYCSOS, which automates that method are described. The system analyzed is one in which a metal hydride heat pump can provide space heating and space cooling powered by energy from solar collectors and electric power generated from solar energy. The principles and basic design of the system are presented, and the computer program is described giving detailed design and performance equations used in the program. The operation of the program is explained, and a sample run is presented. This computer program is part of an effort to design, cost, and evaluate a hydride heat pump for residential use. The computer program is written in standard Fortran IV and was run on a CDC Cyber 74 and Cyber 174 computer. A listing of the program is included as an appendix. This report is Volume 1 of a two-volume document.

Stata 8 Graphics: Options, sub-options and sub-sub-options

OpenAIRE

Tim Collier

2005-01-01

Stata 8 graphics have changed out of all recognition from that available in earlier versions. It was not just that a whole new array of options and sub-options were introduced, but the graph syntax itself completely changed. Just trying to produce a simple plot of x against y using Stata 7 syntax (graph x y) produced bewildering error messages e.g. xgraph_g.new y: class member function not found r(4023) and the like. If you did succeed in working out the new syntax (graph twoway scatter x y) ...

Object-oriented design and programming in medical decision support.

Science.gov (United States)

Heathfield, H; Armstrong, J; Kirkham, N

1991-12-01

The concept of object-oriented design and programming has recently received a great deal of attention from the software engineering community. This paper highlights the realisable benefits of using the object-oriented approach in the design and development of clinical decision support systems. These systems seek to build a computational model of some problem domain and therefore tend to be exploratory in nature. Conventional procedural design techniques do not support either the process of model building or rapid prototyping. The central concepts of the object-oriented paradigm are introduced, namely encapsulation, inheritance and polymorphism, and their use illustrated in a case study, taken from the domain of breast histopathology. In particular, the dual roles of inheritance in object-oriented programming are examined, i.e., inheritance as a conceptual modelling tool and inheritance as a code reuse mechanism. It is argued that the use of the former is not entirely intuitive and may be difficult to incorporate into the design process. However, inheritance as a means of optimising code reuse offers substantial technical benefits.

Extension of a simplified computer program for analysis of solid-propellant rocket motors

Science.gov (United States)

Sforzini, R. H.

1973-01-01

A research project to develop a computer program for the preliminary design and performance analysis of solid propellant rocket engines is discussed. The following capabilities are included as computer program options: (1) treatment of wagon wheel cross sectional propellant configurations alone or in combination with circular perforated grains, (2) calculation of ignition transients with the igniter treated as a small rocket engine, (3) representation of spherical circular perforated grain ends as an alternative to the conical end surface approximation used in the original program, and (4) graphical presentation of program results using a digital plotter.

Proceedings of the workshop on program options in intermediate-energy physics. Volume 1. Summary and panel reports

Energy Technology Data Exchange (ETDEWEB)

Allred, J.C.; Talley, B. (comps.)

1980-05-01

A Workshop on Program Options in Intermediate-Energy Physics sponsored by the US Department of Energy was held at Los Alamos Scientific Laboratory, August 20 to 31, 1979. The scope of the workshop included all laboratories in intermediate-energy physics, worldwide, and all of these sent representatives to the workshop. The workshop addressed itself to the critical questions on nuclear and particle physics and how they can best be investigated by intermediate-energy accelerators. Among the questions that the workshop members considered were: (1) what are the important physics topics which might be understood through research on these accelerators in the next 10 years. These topics include, but are not restricted to, fundamental interactions and symmetries in particle physics, and nuclear modes of motion, structure, and reaction mechanisms; (2) what experiments should be undertaken to carry out the program. What are the kinematical conditions, accuracies, resolutions, and other parameters required to obtain the desired knowledge; (3) which accelerators are best suited for each experiment. What work at other laboratories (low-, intermediate-, or high-energy) could be undertaken to complement and/or supplement the proposed LAMPF program; and (4) what new facility capabilities should be explored for the long-term future. The workshop was divided into small panels in order to promote effective interchange of ideas. After reports to other panels and plenary sessions, the panelists prepared reports stating the results of their deliberations. These reports comprise the principal part of Volume I.

Proceedings of the workshop on program options in intermediate-energy physics. Volume 1. Summary and panel reports

International Nuclear Information System (INIS)

Allred, J.C.; Talley, B.

1980-05-01

A Workshop on Program Options in Intermediate-Energy Physics sponsored by the US Department of Energy was held at Los Alamos Scientific Laboratory, August 20 to 31, 1979. The scope of the workshop included all laboratories in intermediate-energy physics, worldwide, and all of these sent representatives to the workshop. The workshop addressed itself to the critical questions on nuclear and particle physics and how they can best be investigated by intermediate-energy accelerators. Among the questions that the workshop members considered were: (1) what are the important physics topics which might be understood through research on these accelerators in the next 10 years. These topics include, but are not restricted to, fundamental interactions and symmetries in particle physics, and nuclear modes of motion, structure, and reaction mechanisms; (2) what experiments should be undertaken to carry out the program. What are the kinematical conditions, accuracies, resolutions, and other parameters required to obtain the desired knowledge; (3) which accelerators are best suited for each experiment. What work at other laboratories (low-, intermediate-, or high-energy) could be undertaken to complement and/or supplement the proposed LAMPF program; and (4) what new facility capabilities should be explored for the long-term future. The workshop was divided into small panels in order to promote effective interchange of ideas. After reports to other panels and plenary sessions, the panelists prepared reports stating the results of their deliberations. These reports comprise the principal part of Volume I

The Obstacle Version of the Geometric Dynamic Programming Principle: Application to the Pricing of American Options Under Constraints

International Nuclear Information System (INIS)

Bouchard, Bruno; Vu, Thanh Nam

2010-01-01

We provide an obstacle version of the Geometric Dynamic Programming Principle of Soner and Touzi (J. Eur. Math. Soc. 4:201-236, 2002) for stochastic target problems. This opens the doors to a wide range of applications, particularly in risk control in finance and insurance, in which a controlled stochastic process has to be maintained in a given set on a time interval [0,T]. As an example of application, we show how it can be used to provide a viscosity characterization of the super-hedging cost of American options under portfolio constraints, without appealing to the standard dual formulation from mathematical finance. In particular, we allow for a degenerate volatility, a case which does not seem to have been studied so far in this context.

Consolidated fuel reprocessing program

Science.gov (United States)

1985-04-01

A survey of electrochemical methods applications in fuel reprocessing was completed. A dummy fuel assembly shroud was cut using the remotely operated laser disassembly equipment. Operations and engineering efforts have continued to correct equipment operating, software, and procedural problems experienced during the previous uranium compaigns. Fuel cycle options were examined for the liquid metal reactor fuel cycle. In high temperature gas cooled reactor spent fuel studies, preconceptual designs were completed for the concrete storage cask and open field drywell storage concept. These and other tasks operating under the consolidated fuel reprocessing program are examined.

Lesson learned from PSA in the design improvement program of KSNP+

International Nuclear Information System (INIS)

Kim, M.R.; Lim, H.K.; Kang, S.K.; Park, K.S.

2001-01-01

KOPEC (Korea Power Engineering Co.) in conjunction with the client KEPCO (Korea Electric Power Corp.) has been developing a highly competitive Improved Korean Standard Nuclear Power Plant named KSNP+. From the beginning of Design Improvement Program, PSA was carried out to assure that the safety level of KSNP+ is maintained or improved in comparison with that of KSNP, the Korean Standard NPP. To achieve the safety goal of KSNP+, PSA team reviewed all design changes that might affect the plant safety. Design vulnerabilities were identified from the PSA results and safety improvement items were recommended to the system designers. Through the Design Improvement Program, KSNP+ became more reliable, safer and economically competitive than KSNP. This was achieved by systematic approach for design optimization and effective use of PSA technology based on past experience and expertise of nuclear power plant. (author)

Effects of program design on the professional socialization of RN-BSN students.

Science.gov (United States)

Eckhardt, Jo Anne

2002-01-01

The purpose of this study was to examine effects of program design on the bureaucratic and professional role conceptions of registered nurses in baccalaureate nursing programs. Attention to how programs are set up and function has relevance for theory and practice and enables improving frameworks for program planning. The study design embodied qualitative and quantitative elements and used six processes of socialization in organizations as a conceptual guide. Qualitative data collection concerned comparative case studies of three baccalaureate nursing programs and data analysis included narratives detailing program organization and describing student experience. Quantitative matter involved mailed questionnaires to determine graduates' bureaucratic, professional, and service role conceptions. Data analysis (analysis of variance) revealed statistically significant differences in role conceptions (F[3.56] = 4.51) of registered nurses graduating from different baccalaureate programs in nursing. Indications are that nursing programs can be set up to produce equal education and reach certain stated outcomes, yet implicit program processes can impact student learning. Copyright 2002, Elsevier Science (USA). All rights reserved.

Preliminary Design Analysis of a HGD for the NHDD Program at Korea

International Nuclear Information System (INIS)

Song, Kee Nam; Lee, H. Y.; Lee, S. B.; Kim, Y. W.

2007-01-01

Korea Atomic Energy Research Institute is in the process of carrying out a Nuclear Hydrogen Development and Demonstration (NHDD) Program by considering the indirect cycle gas cooled reactors that produce heat at temperatures in the order of 950 .deg. C. A coaxial double-tube Hot Gas Duct (HGD) is a key component connecting the reactor pressure vessel and the intermediate heat exchanger for the NHDD program. Recently, a preliminary design evaluation for the hot gas duct of the NHDD program was carried out. These preliminary design activities include a decision on the geometric dimensions, a strength evaluation, an appropriate material selection, and identifying the design code for the HGD. In this study, a preliminary strength evaluation for the HGD of the NHDD program has been undertaken based on the HTR-10 design concepts. Also, a preliminary evaluation of the creep-fatigue damage for a high temperature HGD structure has been carried out according to the draft code case for Alloy 617. Preliminary strength evaluation results for the HGD showed that the geometric dimensions of the proposed HGD would be acceptable for the design requirements

BS degree in nuclear engineering or a nuclear option

International Nuclear Information System (INIS)

Williams on, T.G.

1988-01-01

Many nuclear engineering educators are concerned about the health of nuclear engineering academic departments. As part of a review of the BS nuclear engineering degree program at the University of Virginia, the authors surveyed several local utilities with operating nuclear plants about their needs for nuclear engineering graduates. The perception of many of the utility executives about a nuclear engineering degree and about a nuclear option in another engineering curriculum does not agree with the way the authors view these two degrees. The responses to two of the survey questions were of particular interest: (1) does your company have a preference between nuclear engineering graduates and graduates in other fields with a nuclear option? (2) what do you consider to be a minimum level of education in nuclear engineering for a nuclear option in mechanical engineering? All of the four utilities that were surveyed stated a preference for mechanical or electrical engineers with a nuclear option, although two indicated that there are certain jobs for which a nuclear engineering graduate is desired

The future of the nuclear option

International Nuclear Information System (INIS)

Frost, B.R.T.

1992-01-01

This paper reports on the future of the nuclear option. No nuclear power reactors have been ordered in the U.S.A. since 1975, but the number of operating reactors has increased to the 115 operating today. The demand for electric power continues to grow. At this time, concern over the environmental effects of fossil fuels has grown; global warming and acid rain effects are major determinants of energy policy. In these circumstances nuclear power may be the only viable option to meet the growing demand for electricity. In the past decade the nuclear power industry has addressed its major critics by standardizing designs, improving operator training, and developing safe methods of disposing of waste products. Fast breeder reactors have taken a new lease on life through the American Integral Fast Reactor (IFR) design which is inherently safe, proliferation resistant, and helps the waste-disposal problem. It will probably not be commercially available until well into the next century. The extension of reactor life raises questions of long-term thermal and radiation effects

Preliminary Neutronics Design Studies for a Molten Salt Blanket LIFE Engine

International Nuclear Information System (INIS)

Powers, J.

2008-01-01

The Laser Inertial Confinement Fusion Fission Energy (LIFE) Program being developed at Lawrence Livermore National Laboratory (LLNL) aims to design a hybrid fission-fusion subcritical nuclear engine that uses a laser-driven Inertial Confinement Fusion (ICF) system to drive a subcritical fission blanket. This combined fusion-fission hybrid system could be used for generating electricity, material transmutation or incineration, or other applications. LIFE does not require enriched fuel since it is a sub-critical system and LIFE can sustain power operation beyond the burnup levels at which typical fission reactors need to be refueled. In light of these factors, numerous options have been suggested and are being investigated. Options being investigated include fueling LIFE engines with spent nuclear fuel to aid in disposal/incineration of commercial spent nuclear fuel or using depleted uranium or thorium fueled options to enhance proliferation resistance and utilize non-fissile materials (1]. LIFE engine blanket designs using a molten salt fuel system represent one area of investigation. Possible applications of a LIFE engine with a molten salt blanket include uses as a spent nuclear fuel burner, fissile fuel breeding platform, and providing a backup alternative to other LIFE engine blanket designs using TRISO fuel particles in case the TRISO particles are found to be unable to withstand the irradiation they will be subjected to. These molten salts consist of a mixture of LiF with UF 4 or ThF 4 or some combination thereof. Future systems could look at using PuF 3 or PuF 4 as well, though no work on such system with initial plutonium loadings has been performed for studies documented in this report. The purpose of this report is to document preliminary neutronics design studies performed to support the development of a molten salt blanket LIFE engine option, as part of the LIFE Program being performed at Lawrence Livermore National laboratory. Preliminary design studies

Preliminary Neutronics Design Studies for a Molten Salt Blanket LIFE Engine

Energy Technology Data Exchange (ETDEWEB)

Powers, J

2008-10-23

The Laser Inertial Confinement Fusion Fission Energy (LIFE) Program being developed at Lawrence Livermore National Laboratory (LLNL) aims to design a hybrid fission-fusion subcritical nuclear engine that uses a laser-driven Inertial Confinement Fusion (ICF) system to drive a subcritical fission blanket. This combined fusion-fission hybrid system could be used for generating electricity, material transmutation or incineration, or other applications. LIFE does not require enriched fuel since it is a sub-critical system and LIFE can sustain power operation beyond the burnup levels at which typical fission reactors need to be refueled. In light of these factors, numerous options have been suggested and are being investigated. Options being investigated include fueling LIFE engines with spent nuclear fuel to aid in disposal/incineration of commercial spent nuclear fuel or using depleted uranium or thorium fueled options to enhance proliferation resistance and utilize non-fissile materials [1]. LIFE engine blanket designs using a molten salt fuel system represent one area of investigation. Possible applications of a LIFE engine with a molten salt blanket include uses as a spent nuclear fuel burner, fissile fuel breeding platform, and providing a backup alternative to other LIFE engine blanket designs using TRISO fuel particles in case the TRISO particles are found to be unable to withstand the irradiation they will be subjected to. These molten salts consist of a mixture of LiF with UF{sub 4} or ThF{sub 4} or some combination thereof. Future systems could look at using PuF{sub 3} or PuF{sub 4} as well, though no work on such system with initial plutonium loadings has been performed for studies documented in this report. The purpose of this report is to document preliminary neutronics design studies performed to support the development of a molten salt blanket LIFE engine option, as part of the LIFE Program being performed at Lawrence Livermore National laboratory

An analysis of international nuclear fuel supply options

Science.gov (United States)

Taylor, J'tia Patrice

As the global demand for energy grows, many nations are considering developing or increasing nuclear capacity as a viable, long-term power source. To assess the possible expansion of nuclear power and the intricate relationships---which cover the range of economics, security, and material supply and demand---between established and aspirant nuclear generating entities requires models and system analysis tools that integrate all aspects of the nuclear enterprise. Computational tools and methods now exist across diverse research areas, such as operations research and nuclear engineering, to develop such a tool. This dissertation aims to develop methodologies and employ and expand on existing sources to develop a multipurpose tool to analyze international nuclear fuel supply options. The dissertation is comprised of two distinct components: the development of the Material, Economics, and Proliferation Assessment Tool (MEPAT), and analysis of fuel cycle scenarios using the tool. Development of MEPAT is aimed for unrestricted distribution and therefore uses publicly available and open-source codes in its development when possible. MEPAT is built using the Powersim Studio platform that is widely used in systems analysis. MEPAT development is divided into three modules focusing on: material movement; nonproliferation; and economics. The material movement module tracks material quantity in each process of the fuel cycle and in each nuclear program with respect to ownership, location and composition. The material movement module builds on techniques employed by fuel cycle models such as the Verifiable Fuel Cycle Simulation (VISION) code developed at the Idaho National Laboratory under the Advanced Fuel Cycle Initiative (AFCI) for the analysis of domestic fuel cycle. Material movement parameters such as lending and reactor preference, as well as fuel cycle parameters such as process times and material factors are user-specified through a Microsoft Excel(c) data spreadsheet

Undergraduate Program: Philadelphia

Science.gov (United States)

Betsock, Lori

2008-08-01

Undergraduate chemical science students—join us in Philadelphia on August 17 and 18, 2008, for an educational and career-oriented program designed specifically for you. Attend symposia about global climate change and clean energy; hear Nobel Laureate F. Sherwood Rowland speak about his fascinating career, "A Life in Tracer Chemistry". Weigh options for your future by attending the Graduate School Reality Check and graduate school recruiting events. All events will take place in the Sheraton Philadelphia City Center at 17th and Race Streets, except the Undergraduate Poster Sessions and Sci-Mix, which will be held in the Pennsylvania Convention Center.

Processing a programming handbook for visual designers and artists

CERN Document Server

Reas, Casey

2014-01-01

The visual arts are rapidly changing as media moves into the web, mobile devices, and architecture. When designers and artists learn the basics of writing software, they develop a new form of literacy that enables them to create new media for the present, and to imagine future media that are beyond the capacities of current software tools. This book introduces this new literacy by teaching computer programming within the context of the visual arts. It offers a comprehensive reference and text for Processing (www.processing.org), an open-source programming language that can be used by students, artists, designers, architects, researchers, and anyone who wants to program images, animation, and interactivity. Written by Processing's cofounders, the book offers a definitive reference for students and professionals. Tutorial chapters make up the bulk of the book; advanced professional projects from such domains as animation, performance, and installation are discussed in interviews with their creators. This secon...

Parameter identification using optimization techniques in the continuous simulation programs FORSIM and MACKSIM

International Nuclear Information System (INIS)

Carver, M.B.; Austin, C.F.; Ross, N.E.

1980-02-01

This report discusses the mechanics of automated parameter identification in simulation packages, and reviews available integration and optimization algorithms and their interaction within the recently developed optimization options in the FORSIM and MACKSIM simulation packages. In the MACKSIM mass-action chemical kinetics simulation package, the form and structure of the ordinary differential equations involved is known, so the implementation of an optimizing option is relatively straightforward. FORSIM, however, is designed to integrate ordinary and partial differential equations of abritrary definition. As the form of the equations is not known in advance, the design of the optimizing option is more intricate, but the philosophy could be applied to most simulation packages. In either case, however, the invocation of the optimizing interface is simple and user-oriented. Full details for the use of the optimizing mode for each program are given; specific applications are used as examples. (O.T.)

SLC energy upgrade program at SLAC

International Nuclear Information System (INIS)

Loew, G.A.; Allen, M.A.; Cassel, R.L.; Dean, N.R.; Konrad, G.T.; Koontz, R.F.; Lebacqz, J.V.

1985-01-01

The SLAC Linear Collider (SLC) must reach a nominal center-of-mass energy of 100 GeV to fulfill its high energy physics goals. This paper describes the energy upgrade program that is being implemented on the SLAC linear accelerator to meet these goals. It includes a discussion of the design requirements and available technical options, the rationale for the adopted solution, and the technical problems involved in the engineering and production of klystrons and modulators

SLC Energy Upgrade Program at SLAC

International Nuclear Information System (INIS)

Loew, G.A.; Allen, M.A.; Cassel, R.L.; Dean, N.R.; Konrad, G.T.; Koontz, R.F.; Lebacqz, J.V.

1985-03-01

The SLAC Linear Collider (SLC) must reach a nominal center-of-mass energy of 100 GeV to fulfill its high energy physics goals. This paper describes the energy upgrade program that is being implemented on the SLAC linear accelerator to meet these goals. It includes a discussion of the design requirements and available technical options, the rationale for the adopted solution, and the technical problems involved in the engineering and production of klystrons and modulators

Situated Research Design and Methodological Choices in Formative Program Evaluation

Science.gov (United States)

Supovitz, Jonathan

2013-01-01

Design-based implementation research offers the opportunity to rethink the relationships between intervention, research, and situation to better attune research and evaluation to the program development process. Using a heuristic called the intervention development curve, I describe the rough trajectory that programs typically follow as they…

Quiet engine program flight engine design study

Science.gov (United States)

Klapproth, J. F.; Neitzel, R. E.; Seeley, C. T.

1974-01-01

The results are presented of a preliminary flight engine design study based on the Quiet Engine Program high-bypass, low-noise turbofan engines. Engine configurations, weight, noise characteristics, and performance over a range of flight conditions typical of a subsonic transport aircraft were considered. High and low tip speed engines in various acoustically treated nacelle configurations were included.

PSYCHOLOGICAL AND SOCIO-ECONOMIC FACTORS IN DESIGN OF AGRICULTURAL PROGRAMMING IN RADIO TEOCELO, VERACRUZ

Directory of Open Access Journals (Sweden)

Antolin Silvestre Martiñón-Martínez

2014-01-01

Full Text Available The mass media, are an important complement in the agricultural extension, however, radio is the most economical mass media, so their potential is huge especially in rural areas. The present study was carried out at a community radio station (Radio Teocelo, with coffee producers, in three municipalities in the area Center of Veracruz, it should be noted that the radio has an audience formed mainly by agricultural producers, also this medium has been used for agricultural extension by the UNCADER (training unit for Rural Development, through an agricultural program called "The Moon in Uncader", with mainly technical information, however, it is necessary to propose relevant socio-economic issues that may be part of an optional agricultural programming, and/or complement the technical programming that is transmitted by the agricultural program. The study found a positive attitude to the proposed socio-economic issues, since most was obtained 80% of positive responses, highlighting the transmission of information on: marketing, government programs, visits to successful producers and transmission of successful cases of successful producers, also adopted a positive attitude for the program is disseminated by mass media mainly Teocelo Radio and are willing to personally spread mainly with friends.

Development strategy and conceptual design of China Lead-based Research Reactor

International Nuclear Information System (INIS)

Wu, Yican; Bai, Yunqing; Song, Yong; Huang, Qunying; Zhao, Zhumin; Hu, Liqin

2016-01-01

Highlights: • China LEAd-based Reactor (CLEAR) proposed by Institute of Nuclear Energy Safety Technology (INEST) is selected as the ADS reference reactor. • The Chinese ADS development program consists of three stages, and during the first stage, a 10 MW th lead-based research reactor named CLEAR-I will be built with subcritical and critical dual-mode operation capability for validation of ADS transmutation system and lead cooled fast reactor technology. • Major design principles of CLEAR-I are oriented at technology feasibility, safety reliability, experiment flexibility and technology continuity. Followed by the development strategy and design principles, CLEAR-I design options and conceptual design scenarios are presented. - Abstract: Chinese Academy of Sciences (CAS) launched an engineering project to develop an Accelerator Driven System (ADS) for nuclear waste transmutation since 2011, and China LEAd-based Reactor (CLEAR) proposed by Institute of Nuclear Energy Safety Technology (INEST) is selected as the ADS reference reactor. In this paper, the development strategy and conceptual design of China Lead-based Research Reactor are proposed. The Chinese ADS development program consists of three stages, and during the first stage, a 10 MW th lead-based research reactor named CLEAR-I will be built with subcritical and critical dual-mode operation capability for validation of ADS transmutation system and lead cooled fast reactor technology. Major design principles of CLEAR-I are oriented at technology feasibility, safety reliability, experiment flexibility and technology continuity. Followed by the development strategy and design principles, CLEAR-I design options and conceptual design scenarios are presented.

Comparative study of low and high aspect ratio devices for ITER design options

International Nuclear Information System (INIS)

Sugihara, Masayoshi; Tada, Eisuke; Shimomura, Yasuo; Tsunematsu, Toshihide; Nishio, Satoshi; Nakazato, Toshiko; Murakami, Yoshiki; Koizumi, Koichi

1992-09-01

Comparative study on the plasma performance and the engineering characteristics of low and high aspect ratio devices for ITER (International Thermonuclear Experimental Reactor) design option is done to examine quantitatively the expected merit and demerit of high aspect ratio device on steady state operation. Device parameters of aspect ratio A=3 and 4 are chosen based on ITER-power scaling law. Improvement of steady state operation with A=4 is found only moderate. Reduction of stability margin in vertical instability is about 20% and plasma elongation must be decreased from 2 down to about 1.8 to recover this reduction of stability margin with A=4. If such lower elongation is employed, single null divertor configuration should be employed to reduce the capacity of poloidal field system. Detailed 2D divertor code calculation shows that peak heat load per unit area of A=4 device with SN configuration increases compared with A=3 device with DN configuration, contrary to the predictions so far made. Preliminary engineering studies indicate that A=4 device would have less space for handling the in-vessel components and doubled toroidal field magnet weight and winding length, and hence is less desirable when compared with the present ITER design (A=3). Based on these examinations, it is concluded that high aspect ratio device does not have remarkable advantage than low aspect ratio device, and the latter device has similar capability for the prospect of future commercial reactor to the former device. (J.P.N.)

Free energy option and its relevance to improve domestic energy demands in southern Nigeria

Directory of Open Access Journals (Sweden)

Moses Eterigho Emetere

2016-11-01

Full Text Available The aim of this paper is to seek an energy option that would benefit the growing energy demands. Domestic energy demands in southern Nigeria had increased greatly due to failing power programs and seasonal migrations. The fossil fuel option is gradually fading away due to environmental pollution and recent dynamic cost. The renewable energy option had been celebrated with little success in the coastal area of southern Nigeria. At the moment, the renewable energy option is very expensive with little guarantee on its efficiency with time. The data set used for this study was obtained from the Davis weather installation in Covenant University. The free energy option was considered. The cost and its environmental implication for domestic use were comparatively discussed alongside other energy options — using the Life cycle cost analysis. It was found out that free energy option is more affordable and efficient for domestic use.

Cognitive and Affective Aspects of Creative Option Generation in Everyday Life Situations.

Science.gov (United States)

Schweizer, T Sophie; Schmalenberger, Katja M; Eisenlohr-Moul, Tory A; Mojzisch, Andreas; Kaiser, Stefan; Funke, Joachim

2016-01-01

Which factors influence a human being's ability to develop new perspectives and be creative? This ability is pivotal for any context in which new cognitions are required, such as innovative endeavors in science and art, or psychotherapeutic settings. In this article, we seek to bring together two research programs investigating the generation of creative options: On the one hand, research on option generation in the decision-making literature and, on the other hand, cognitive and clinical creativity research. Previous decision-making research has largely neglected the topic of generating creative options. Experiments typically provided participants with a clear set of options to choose from, but everyday life situations are less structured and allow countless ways to react. Before choosing an option, agents have to self-generate a set of options to choose from. Such option generation processes have only recently moved to the center of attention. The present study examines the creative quality of self-generated options in daily life situations. A student sample (N = 48) generated options for action in 70 briefly described everyday life scenarios. We rated the quality of the options on three dimensions of creativity- originality, feasibility, and divergence -and linked these qualities to option generation fluency (speed and number of generated options), situational features like the familiarity and the affective valence of the situation in which the options were generated, and trait measures of cognitive performance. We found that when situations were familiar to the participant, greater negative affective valence of the situation was associated with more originality and divergence of generated options. We also found that a higher option generation fluency was associated with a greater maximal originality of options. We complete our article with a joint research agenda for researchers in the decision-making field focusing on option generation and, on the other hand

77 FR 58600 - Self-Regulatory Organizations; BOX Options Exchange LLC; Notice of Filing and Immediate...

Science.gov (United States)

2012-09-21

... approving expansion of STO Program)[sic]. \\9\\ These include, without limitation, options, equities, futures... hedging strategies across various investment platforms (e.g. equity and ETF, index, derivatives, futures... Web site, strike prices for options on futures may be at an interval of $.05, $.10, and $.25 per...

Use of the Generating Options for Active Risk Control (GO-ARC) Technique can lead to more robust risk control options.

Science.gov (United States)

Card, Alan J; Simsekler, Mecit Can Emre; Clark, Michael; Ward, James R; Clarkson, P John

2014-01-01

Risk assessment is widely used to improve patient safety, but healthcare workers are not trained to design robust solutions to the risks they uncover. This leads to an overreliance on the weakest category of risk control recommendations: administrative controls. Increasing the proportion of non-administrative risk control options (NARCOs) generated would enable (though not ensure) the adoption of more robust solutions. Experimentally assess a method for generating stronger risk controls: The Generating Options for Active Risk Control (GO-ARC) Technique. Participants generated risk control options in response to two patient safety scenarios. Scenario 1 (baseline): All participants used current practice (unstructured brainstorming). Scenario 2: Control group used current practice; intervention group used the GO-ARC Technique. To control for individual differences between participants, analysis focused on the change in the proportion of NARCOs for each group. Proportion of NARCOs decreased from 0.18 at baseline to 0.12. Intervention group: Proportion increased from 0.10 at baseline to 0.29 using the GO-ARC Technique. Results were statistically significant. There was no decrease in the number of administrative controls generated by the intervention group. The Generating Options for Active Risk Control (GO-ARC) Technique appears to lead to more robust risk control options.

ACCOUNTING FOR OPTIONS AND ANALYSIS OF USE OF OPTION COMBINATION STRATEGIES

Directory of Open Access Journals (Sweden)

I. Derun

2016-08-01

Full Text Available The article deals with problems of accounting for options in Ukraine, namely: value expression of initial cost of options, their revaluation, accounting of premiums, financial assets and financial liabilities and variation margin. The paper offers ways of solution of these problems which based on harmonization with IAS 32, IAS 39, IFRS 7 and IFRS 9. The study considers option combination strategies (straddle, strangle, strap, strip and approaches of identification of possible financial results for investors which use these strategies. Examples of possible financial results are provided for buyers and sellers of options which use option combination strategies.

Environmental and waste disposal options in nuclear engineering curricula

International Nuclear Information System (INIS)

Elleman, T.S.; Gilligan, J.G.

1991-01-01

The strong national emphasis on waste and environmental issues has prompted increasing interest among nuclear engineering students in study options that will prepare them for careers in these areas. Student interest appears to focus principally on health physics, radioactive waste disposal, and environmental interactions with radionuclides. One motivation for this interest appears to be the growing national programs in environmental restoration and waste remediation that have produced fellowship support for nuclear engineering students as well as employment opportunities. Also, the recent National Academy of sciences study on nuclear engineering education specifically emphasized the importance of expanding nuclear engineering curricula and research programs to include a greater emphasis on radioactive waste and environmental issues. The North Carolina State University (NCSU) Department of Nuclear Engineering is attempting to respond to these needs through the development of course options that will allow students to acquire background in environmental subjects as a complement to the traditional nuclear engineering education

Option contracts in fresh produce supply chain with circulation loss

Directory of Open Access Journals (Sweden)

Chong Wang

2013-03-01

Full Text Available Purpose: The purpose of this paper is to investigate management decisions via option contracts in a two-stage supply chain in which a fresh produce supplier sells to a retailer, considering the circulation loss of the fresh produce. Design/methodology/approach: Authors propose a Stackelberg model to analyze the supply chain members’ decisions in the decentralized supply chain compared with the integrated one under the newsvendor framework. Findings: The results illustrate that there exists a unique optimal option order quantity for the retailer and a unique optimal option order price for the supplier giving certain conditions; furthermore, option contracts cannot coordinate the fresh produce supply chain when the retailer only orders options. Originality/value: Agricultural products especially fresh produce’s characteristics such as circulation loss and high risk are considered. Option contracts and game theory are combined to manage the fresh produce supply chain’s risk. The proposed tool and models are hoped to shed light to the future works in the field of supply chain risk management.