WorldWideScience

Sample records for products accumulation calculations

  1. Calculated model of radioactive fission and corrosion product accumulation and distribution in a fast reactor sodium coolant circuit

    International Nuclear Information System (INIS)

    Kizin, V.D.; Konyashov, V.V.

    1987-01-01

    A simple calculation procedure of radioactive products accumulation and distribution in a primary circuit has been developed on the basis of experimental investigations at the BOR-60 reactor. Common knowledge on the impurity products transfer at the liquid-solid and liquid-gas phase boundary is taken. Use is made of the typical in reactor physics relationships for the description of the products transition to the equipment surfaces, of fission products release, metal corrosion and others. Satisfactory agreement of the calculation data with the experimental ones has been obtained. (orig.)

  2. Accumulated dose calculations in Indian PHWRs under DBA

    International Nuclear Information System (INIS)

    Nesaraj, David; Pradhan, A.S.; Bhardwaj, S.A.

    1996-01-01

    Accumulated gamma dose inside reactor building due to release of fission products from equilibrium core of Indian PHWR under accident condition has been assessed. The assessment has been done for the radiation tolerance limit of the critical equipment inside reactor building. The basic source data has been generated using computer code ORIGEN2 written and developed by Oak Ridge National Laboratory, USA (ORNL). This paper discusses the details of the calculations done on the basis of certain assumption which are mentioned at relevant places. The results indicate accumulated gamma dose at a few typical locations inside reactor building under accident condition. (author). 1 ref., 1 tab., 1 fig

  3. The lipid accumulation product as a useful index for identifying abnormal glucose regulation in young Korean women.

    Science.gov (United States)

    Oh, J-Y; Sung, Y-A; Lee, H J

    2013-04-01

    The lipid accumulation product, a combination of waist circumference and triglycerides concentration, has been suggested as a better marker for abnormal glucose regulation than BMI. We aimed to compare the lipid accumulation product and BMI as useful markers for abnormal glucose regulation in young Korean women. The lipid accumulation product was calculated using the formula [waist circumference (cm) - 58] × triglycerides (mmol/l). Glucose tolerance status was determined using a 75-g oral glucose tolerance test in 2810 Korean women aged 18-39 years from the general population. The prevalence of abnormal glucose regulation was 6.8% (isolated impaired fasting glucose 1.8%, isolated impaired glucose tolerance 4.0%; impaired fasting glucose + impaired glucose tolerance 0.4% and diabetes mellitus 0.6%). According to the quintile distributions of the lipid accumulation product and BMI, women with a lipid accumulation product quintile greater than their BMI quintile exhibited significantly greater areas under the curve and higher levels of 2-h post-load glucose, insulin, homeostasis model analysis of insulin resistance and lipid profiles than did women with a BMI quintile greater than their lipid accumulation product quintile. Multiple logistic regression revealed that the lipid accumulation product exhibited a higher odds ratio for abnormal glucose regulation than did BMI after adjusting for age, systolic blood pressure, HDL cholesterol, previous history of gestational diabetes and family history of diabetes (odds ratios 3.5 and 2.6 of the highest vs. the lowest quintiles of lipid accumulation product and BMI, respectively). The lipid accumulation product could be useful for identifying the young Korean women with abnormal glucose regulation. © 2012 The Authors. Diabetic Medicine © 2012 Diabetes UK.

  4. Hardware matrix multiplier/accumulator for lattice gauge theory calculations

    International Nuclear Information System (INIS)

    Christ, N.H.; Terrano, A.E.

    1984-01-01

    The design and operating characteristics of a special-purpose matrix multiplier/accumulator are described. The device is connected through a standard interface to a host PDP11 computer. It provides a set of high-speed, matrix-oriented instructions which can be called from a program running on the host. The resulting operations accelerate the complex matrix arithmetic required for a class of Monte Carlo calculations currently of interest in high energy particle physics. A working version of the device is presently being used to carry out a pure SU(3) lattice gauge theory calculation using a PDP11/23 with a performance twice that obtainable on a VAX11/780. (orig.)

  5. Phytomass production and nutrient accumulation by green manure species

    Directory of Open Access Journals (Sweden)

    José Carlos Soares Mangaravite

    2014-10-01

    Full Text Available Green manuring is recognized as a viable alternative to improve nutrient cycling in soils. The aim of this study was to evaluate the phytomass production and nutrient accumulation in shoots of the summer green manures jack bean [Canavalia ensiformis (L. DC.], dwarf pigeon pea (Cajanus cajanvar var. Flavus DC., dwarf mucuna [Mucuna deeringiana (Bort Merr] and sunn hemp (Crotalaria juncea L., under nitrogen fertilization and/or inoculation with N-fixing bacteria. A split plot design was arranged with the four Fabaceae species as main plots and nitrogen fertilization (with and without and inoculation with diazotrophic bacteria (with and without as the subplots, in a 2² factorial. The experiment was arranged as a randomized complete block design with four replications. In the conditions of this trial, the sunn hemp had the highest production of shoot phytomass (12.4 Mg ha-1 and nutrient accumulation, while the dwarf mucuna had the lowest production of shoot phytomass (3.9 Mg ha-1 and nutrient accumulation. The results showed no effect of nitrogen fertilization or inoculation with N-fixing bacteria on the production of shoot phytomass and nutrient accumulation, except for inoculation without nitrogen fertilization, resulting in greater P accumulation (p <0.05 in the sunn hemp and greater Zn and Mn accumulation in the dwarf mucuna. These findings indicate that N fertilization or inoculation with N2-fixing bacteria for Fabaceae are low efficiency practices in the edaphoclimatic conditions of this study.

  6. PABLM: a computer program to calculate accumulated radiation doses from radionuclides in the environment

    Energy Technology Data Exchange (ETDEWEB)

    Napier, B.A.; Kennedy, W.E. Jr.; Soldat, J.K.

    1980-03-01

    A computer program, PABLM, was written to facilitate the calculation of internal radiation doses to man from radionuclides in food products and external radiation doses from radionuclides in the environment. This report contains details of mathematical models used and calculational procedures required to run the computer program. Radiation doses from radionuclides in the environment may be calculated from deposition on the soil or plants during an atmospheric or liquid release, or from exposure to residual radionuclides in the environment after the releases have ended. Radioactive decay is considered during the release of radionuclides, after they are deposited on the plants or ground, and during holdup of food after harvest. The radiation dose models consider several exposure pathways. Doses may be calculated for either a maximum-exposed individual or for a population group. The doses calculated are accumulated doses from continuous chronic exposure. A first-year committed dose is calculated as well as an integrated dose for a selected number of years. The equations for calculating internal radiation doses are derived from those given by the International Commission on Radiological Protection (ICRP) for body burdens and MPC's of each radionuclide. The radiation doses from external exposure to contaminated water and soil are calculated using the basic assumption that the contaminated medium is large enough to be considered an infinite volume or plane relative to the range of the emitted radiations. The equations for calculations of the radiation dose from external exposure to shoreline sediments include a correction for the finite width of the contaminated beach.

  7. PABLM: a computer program to calculate accumulated radiation doses from radionuclides in the environment

    International Nuclear Information System (INIS)

    Napier, B.A.; Kennedy, W.E. Jr.; Soldat, J.K.

    1980-03-01

    A computer program, PABLM, was written to facilitate the calculation of internal radiation doses to man from radionuclides in food products and external radiation doses from radionuclides in the environment. This report contains details of mathematical models used and calculational procedures required to run the computer program. Radiation doses from radionuclides in the environment may be calculated from deposition on the soil or plants during an atmospheric or liquid release, or from exposure to residual radionuclides in the environment after the releases have ended. Radioactive decay is considered during the release of radionuclides, after they are deposited on the plants or ground, and during holdup of food after harvest. The radiation dose models consider several exposure pathways. Doses may be calculated for either a maximum-exposed individual or for a population group. The doses calculated are accumulated doses from continuous chronic exposure. A first-year committed dose is calculated as well as an integrated dose for a selected number of years. The equations for calculating internal radiation doses are derived from those given by the International Commission on Radiological Protection (ICRP) for body burdens and MPC's of each radionuclide. The radiation doses from external exposure to contaminated water and soil are calculated using the basic assumption that the contaminated medium is large enough to be considered an infinite volume or plane relative to the range of the emitted radiations. The equations for calculations of the radiation dose from external exposure to shoreline sediments include a correction for the finite width of the contaminated beach

  8. Nutrient accumulation and biomass production of alfafa after soil amendment with silicates

    Directory of Open Access Journals (Sweden)

    Angélica Cristina Fernandes Deus

    2014-06-01

    Full Text Available Studies on the use of silicate correctives in agriculture show that they have great potential to improve soil chemical characteristics, however, little information is available on the reactivity rates of their particle-size fractions. This study investigated whether the reactivity rates obtained experimentally could be considered in the calculation of ECC (effective calcium carbonate for soil liming, promoting adequate development of alfalfa plants. Six treatments were evaluated in the experiment, consisting of two slag types applied in two rates. The experimental ECC was used to calculate one of the rates and the ECC determined in the laboratory was used to calculate the other. Rates of limestone and wollastonite were based on the ECC determined in laboratory. The rates of each soil acidity corretive were calculated to increase the base saturation to 80%. The treatments were applied to a Rhodic Hapludox and an Alfisol Ferrudalfs. The methods for ECC determination established for lime can be applied to steel slag. The application of slag corrected soil acidity with consequent accumulation of Ca, P, and Si in alfalfa, favoring DM production.

  9. Comparison of Lipid Accumulation Product Index with Body Mass Index and Waist Circumference as a Predictor of Metabolic Syndrome in Indian Population.

    Science.gov (United States)

    Ray, Lopamudra; Ravichandran, Kandasamy; Nanda, Sunil Kumar

    2018-06-01

    Metabolic syndrome (MetS), which confers a high risk for cardiovascular diseases, needs early diagnosis and treatment to reduce morbidity and mortality. Lipid accumulation product index has been reported to be an inexpensive marker of visceral fat and metabolic syndrome. This study aimed to evaluate lipid accumulation product index as a marker for metabolic syndrome in the Indian population where the prevalence of the condition is steadily increasing. A hospital-based, case-control study was conducted with 72 diagnosed cases of metabolic syndrome and 79 control subjects. In all the participants, body mass index (BMI) and lipid accumulation product index were calculated. The difference between cases and controls in BMI, waist circumference (WC), and lipid accumulation product index was assessed by Mann-Whitney U test/unpaired t-test. Associations of BMI, WC, and lipid accumulation product index with metabolic syndrome were compared by multiple logistic regression analysis and receiver operating characteristic analysis. BMI, WC, and lipid accumulation product index were significantly higher in metabolic syndrome (P product index had the highest prediction accuracy. The parameter also had a high area under curve of 0.901 (95% confidence interval 0.85-0.95) and a high sensitivity (76.4%), specificity (91.1%), positive predictive value (88.7%), and negative predictive value (80.9%) for detection of metabolic syndrome. In the Indian population, lipid accumulation product index is a better predictor of metabolic syndrome compared to BMI and WC and should be incorporated in laboratory reports as early, accurate, and inexpensive indicator of metabolic syndrome.

  10. Calculation of Heat Exchange and Changing Phase Ratio in Extended Flowing Heat Accumulators on Phase Transitions with Rectangular Inserts

    Directory of Open Access Journals (Sweden)

    I. G. Zorina

    2016-01-01

    Full Text Available To use the renewable power sources such as solar, wind, biogas, and others is complicated because of their sporadic supply. Thus and so, energy accumulation makes the user independent on the operating mode of the power source.Some of the heat accumulation methods can be realized with accumulators using phase transitions and based on the heat storage materials that change their state of aggregation during storage and rejection of thermal energy. In comparison with the gravel or liquid heat accumulators these devices are compact and provide high density of stored energy. To intensify heat exchange in such devices, are used highly heat-conductive metallic inсlusions of different shape, capsular laying or heat storage materials placed in the form of inserts, extended heat exchange surfaces, etc.Heat transfer of accumulator using phase transitions is calculated through solving a nonlinear Stefan problem. For calculation, are, usually, used various sufficiently time-consuming methods.The paper presents a heat transfer calculation when changing the aggregation state of substance. Its recommendation is to use the analytical dependences that allow calculation of heat exchange characteristics with charging phase transition accumulators of a capsular type in which a heat storage material is in cross-inserts.It is assumed that heat transfer in the coolant flow is one-dimensional, thermal and physical properties of heat storage material and coolant are constant, and heat transfer in the accumulator using phase transitions is quasi-stationary.

  11. Changing Patterns of Publication Productivity: Accumulative Advantage or Institutional Isomorphism?

    Science.gov (United States)

    Dey, Eric L.; Milem, Jeffrey F.; Berger, Joseph B.

    1997-01-01

    Investigates two competing perspectives, accumulated advantage and institutional isomorphism, on the relationship between publication productivity and institutional hierarchy. Accumulated advantage refers to the continuing attraction of students, faculty, and research dollars to prestige universities. Institutional isomorphism denotes the tendency…

  12. Parallelizing flow-accumulation calculations on graphics processing units—From iterative DEM preprocessing algorithm to recursive multiple-flow-direction algorithm

    Science.gov (United States)

    Qin, Cheng-Zhi; Zhan, Lijun

    2012-06-01

    As one of the important tasks in digital terrain analysis, the calculation of flow accumulations from gridded digital elevation models (DEMs) usually involves two steps in a real application: (1) using an iterative DEM preprocessing algorithm to remove the depressions and flat areas commonly contained in real DEMs, and (2) using a recursive flow-direction algorithm to calculate the flow accumulation for every cell in the DEM. Because both algorithms are computationally intensive, quick calculation of the flow accumulations from a DEM (especially for a large area) presents a practical challenge to personal computer (PC) users. In recent years, rapid increases in hardware capacity of the graphics processing units (GPUs) provided in modern PCs have made it possible to meet this challenge in a PC environment. Parallel computing on GPUs using a compute-unified-device-architecture (CUDA) programming model has been explored to speed up the execution of the single-flow-direction algorithm (SFD). However, the parallel implementation on a GPU of the multiple-flow-direction (MFD) algorithm, which generally performs better than the SFD algorithm, has not been reported. Moreover, GPU-based parallelization of the DEM preprocessing step in the flow-accumulation calculations has not been addressed. This paper proposes a parallel approach to calculate flow accumulations (including both iterative DEM preprocessing and a recursive MFD algorithm) on a CUDA-compatible GPU. For the parallelization of an MFD algorithm (MFD-md), two different parallelization strategies using a GPU are explored. The first parallelization strategy, which has been used in the existing parallel SFD algorithm on GPU, has the problem of computing redundancy. Therefore, we designed a parallelization strategy based on graph theory. The application results show that the proposed parallel approach to calculate flow accumulations on a GPU performs much faster than either sequential algorithms or other parallel GPU

  13. Calculation on maximum accumulation of Pu-239 and Pu-241 from aqueous homogeneous reactor

    International Nuclear Information System (INIS)

    Ikhlas H Siregar; Frida Agung R; Suharyana; Azizul Khakim; Dahman Siregar

    2016-01-01

    Calculations on maximum accumulation of Pu-239 and Pu-241 using MCNPX computer code with UO_2(NO_3)_2 fuel solution enriched by 19.75% operating at temperature 80°C have been conducted. AHR design was simulated with cylindrical core having diameter of 63.4 cm and 122 cm high. From this geometry we found the reactor was critical with density 108 gr U/L of UO_2(NO_3)_2 solution. The result showed that multiplication factor (k_e_f_f) of AHR was 1.05284. Then the burn up calculations were done for various time intervals from 5 days until 285 years to analyze the result. From calculation, it was found out that the saturated concentration of Pu-239 was reached after 40-50 years of operation, producing 1.23 x 102 gr and the activity 7.645 Ci. While for operate time of AHR to produce Pu-241 should under 80 years with mass 21.7 gr and the activity 2.247 x 103 Ci. The accumulations of both isotopes are considered to be small, having low potential for misusing them for producing nuclear weapon. (author)

  14. Factors Influencing Biogenic Amines Accumulation in Dairy Products

    Science.gov (United States)

    Linares, Daniel M.; del Río, Beatriz; Ladero, Victor; Martínez, Noelia; Fernández, María; Martín, María Cruz; Álvarez, Miguel A.

    2012-01-01

    Fermented foods are among the food products more often complained of having caused episodes of biogenic amines (BA) poisoning. Concerning milk-based fermented foods, cheese is the main product likely to contain potentially harmful levels of BA, specially tyramine, histamine, and putrescine. Prompted by the increasing awareness of the risks related to dietary uptake of high biogenic amine loads, in this review we report all those elaboration and processing technological aspects affecting BA biosynthesis and accumulation in dairy foods. Improved knowledge of the factors involved in the synthesis and accumulation of BA should lead to a reduction in their incidence in milk products. Synthesis of BA is possible only when three conditions converge: (i) availability of the substrate amino acids; (ii) presence of microorganisms with the appropriate catabolic pathway activated; and (iii) environmental conditions favorable to the decarboxylation activity. These conditions depend on several factors such as milk treatment (pasteurization), use of starter cultures, NaCl concentration, time, and temperature of ripening and preservation, pH, temperature, or post-ripening technological processes, which will be discussed in this chapter. PMID:22783233

  15. Accumulative effect of food residues on intestinal gas production.

    Science.gov (United States)

    Mego, M; Accarino, A; Malagelada, J-R; Guarner, F; Azpiroz, F

    2015-11-01

    As mean transit time in the colon is longer than the interval between meals, several consecutive meal loads accumulate, and contribute to colonic biomass. Our aim was to determine the summation effect of fermentable food residues on intestinal gas production. In eight healthy subjects, the volume of endogenous intestinal gas produced in the intestine over a 4-h period was measured by means of a wash-out technique, using an exogenous gas infusion into the jejunum (24 mL/min) and collection of the effluent via a rectal Foley catheter. The exogenous gas infused was labeled (5% SF6 ) to calculate the proportion of endogenous intestinal gas evacuated. In each subject, four experiments were performed ≥1 week apart combining a 1-day high- or low-flatulogenic diet with a test meal or fast. Basal conditions: on the low-flatulogenic diet, intestinal gas production during fasting over the 4-h study period was 609 ± 63 mL. Effect of diet: during fasting, intestinal gas production on the high-flatulogenic diet was 370 ± 146 mL greater than on the low-flatulogenic diet (p = 0.040). Effect of test meal: on the low-flatulogenic diet, intestinal gas production after the test meal was 681 ± 114 mL greater than during fasting (p = 0.001); a similar effect was observed on the high-flatulogenic diet (599 ± 174 mL more intestinal gas production after the test meal than during fasting; p = 0.021). Our data demonstrate temporal summation effects of food residues on intestinal gas production. Hence, intestinal gas production depends on pre-existing and on recent colonic loads of fermentable foodstuffs. © 2015 John Wiley & Sons Ltd.

  16. Accumulation of sucrose in irradiated agricultural products

    International Nuclear Information System (INIS)

    Hayashi, T.

    1986-01-01

    Irradiation of agricultural products with ionizing radiation causes various physiological changes and one of the interesting phenomena is the increase of sucrose in irradiated potatoes. The relationship, however, between sucrose content and irradiation dose was not clarified. The author has made the relationship clear and found out that the sucrose content once enhanced by a high dose of irradiation does not lower during storage for a long period. It has been found that the sucrose accumulation caused by irradiation occurred in sweet potatoes and chestnuts as well as potatoes. In this article the effect of gamma-irradiation on the sucrose content of potato tubers, sweet potato roots and chestnuts will be reviewed and the mechanism of this sucrose accumulation will be discussed

  17. Accumulation of sucrose in irradiated agricultural products

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, T. [National Food Research Inst., Tsukuba, Ibaraki (Japan)

    1986-03-15

    Irradiation of agricultural products with ionizing radiation causes various physiological changes and one of the interesting phenomena is the increase of sucrose in irradiated potatoes. The relationship, however, between sucrose content and irradiation dose was not clarified. The author has made the relationship clear and found out that the sucrose content once enhanced by a high dose of irradiation does not lower during storage for a long period. It has been found that the sucrose accumulation caused by irradiation occurred in sweet potatoes and chestnuts as well as potatoes. In this article the effect of gamma-irradiation on the sucrose content of potato tubers, sweet potato roots and chestnuts will be reviewed and the mechanism of this sucrose accumulation will be discussed.

  18. Bridging the Barriers: Knowledge Connections, Productivity, and Capital Accumulation

    OpenAIRE

    R. Quentin Grafton; Tom Kompas; P. Dorian Owen

    2004-01-01

    The paper explains the large differences in cross-country productivity performance by modeling and testing the effects of social barriers to communication on productivity and capital accumulation. In an optimal growth model, social barriers to communication that impede the formation of knowledge connections are shown to reduce both transitory and steady-state levels of total factor productivity (TFP), per capita consumption, and reproducible capital. A ‘bridging’ parameter in the growth model...

  19. Radiation characteristics of spent nuclear fuel at accumulation in long-term storage

    International Nuclear Information System (INIS)

    Bergelson, Boris R.; Gerasimov, Aleksander S.

    1999-01-01

    Time dependence of a decay heat power and radiotoxicity of a single spent nuclear fuel unloading of VVER-1000 reactors at its storage or the same characteristics in accumulation mode with annual addition of spent nuclear fuel in long-term storage are investigated. At calculations of decay heat power, the contributions of alpha-, beta-, and gamma- irradiations were taken into account, at calculations of a radiotoxicity - maximum permissible activity of nuclides in air and in water were taken into account. It is determined that at accumulation less than 100 years, the main contribution to decay heat power is given by fission products, at further storage the power is determined in greater degree by actinides. The radiotoxicity of actinides by air is rich greater than that of fission products - more than 50 times in beginning of a storage and by 2-3 orders of magnitude after 100 and more years. A radiotoxicity of fission products by water at accumulation less than 20 years is a little bit more than actinides, at further accumulation the contribution of fission products decreases. At time of accumulation 100 years, the fission products give the contribution in total radiotoxicity about 40%, at time 1000 years - about 7%. (author)

  20. Atmospheric Pb and Ti accumulation rates from Sphagnum moss: dependence upon plant productivity.

    Science.gov (United States)

    Kempter, H; Krachler, M; Shotyk, W

    2010-07-15

    The accumulation rates of atmospheric Pb and Ti were obtained using the production rates of Sphagnum mosses collected in four ombrotrophic bogs from two regions of southern Germany: Upper Bavaria (Oberbayern, OB) and the Northern Black Forest (Nordschwarzwald, NBF). Surfaces of Sphagnum carpets were marked with plastic mesh and one year later the production of plant matter was harvested. Metal concentrations were determined in acid digests using sector field ICP-MS employing well established analytical procedures. Up to 12 samples (40 x 40 cm) were collected per site, and 6-10 sites were investigated per bog. Variations within a given sampling site were in the range 2.3-4x for Pb concentrations, 1.8-2.5x for Ti concentrations, 3-8.3x for Pb/Ti, 5.6-7.8x for Pb accumulation rates, and 2.3-6.4x for Ti accumulation rates. However, the median values of these parameters for the sites (6-10 per bog) were quite consistent. The mosses from the bogs in NBF exhibited significantly greater productivity (187-202 g m(-2) a(-1)) compared to the OB peat bogs (71-91 g m(-2) a(-1)), and these differences had a pronounced effect on the Pb and Ti accumulation rates. Highly productive mosses showed no indication of a "dilution effect" of Pb or Ti concentrations, suggesting that more productive plants were simply able to accumulate more particles from the air. The median rates of net Pb accumulation by the mosses are in excellent agreement with the fluxes obtained by direct atmospheric measurements at nearby monitoring stations in both regions (EMEP and MAPESI data).

  1. Activation Product Inverse Calculations with NDI

    Energy Technology Data Exchange (ETDEWEB)

    Gray, Mark Girard [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-09-27

    NDI based forward calculations of activation product concentrations can be systematically used to infer structural element concentrations from measured activation product concentrations with an iterative algorithm. The algorithm converges exactly for the basic production-depletion chain with explicit activation product production and approximately, in the least-squares sense, for the full production-depletion chain with explicit activation product production and nosub production-depletion chain. The algorithm is suitable for automation.

  2. Stillage reflux in food waste ethanol fermentation and its by-product accumulation.

    Science.gov (United States)

    Ma, Hongzhi; Yang, Jian; Jia, Yan; Wang, Qunhui; Tashiro, Yukihiro; Sonomoto, Kenji

    2016-06-01

    Raw materials and pollution control are key issues for the ethanol fermentation industry. To address these concerns, food waste was selected as fermentation substrate, and stillage reflux was carried out in this study. Reflux was used seven times during fermentation. Corresponding ethanol and reducing sugar were detected. Accumulation of by-products, such as organic acid, sodium chloride, and glycerol, was investigated. Lactic acid was observed to accumulate up to 120g/L, and sodium chloride reached 0.14mol/L. Other by-products did not accumulate. The first five cycles of reflux increased ethanol concentration, which prolonged fermentation time. Further increases in reflux time negatively influenced ethanol fermentation. Single-factor analysis with lactic acid and sodium chloride demonstrated that both factors affected ethanol fermentation, but lactic acid induced more effects. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. MODELING OF TEMPERATURE FIELDS IN A SOLID HEAT ACCUMULLATORS

    Directory of Open Access Journals (Sweden)

    S. S. Belimenko

    2016-10-01

    Full Text Available Purpose. Currently, one of the priorities of energy conservation is a cost savings for heating in commercial and residential buildings by the stored thermal energy during the night and its return in the daytime. Economic effect is achieved due to the difference in tariffs for the cost of electricity in the daytime and at night. One of the most common types of devices that allow accumulating and giving the resulting heat are solid heat accumulators. The main purpose of the work: 1 software development for the calculation of the temperature field of a flat solid heat accumulator, working due to the heat energy accumulation in the volume of thermal storage material without phase transition; 2 determination the temperature distribution in its volumes at convective heat transfer. Methodology. To achieve the study objectives a heat transfer theory and Laplace integral transform were used. On its base the problems of determining the temperature fields in the channels of heat accumulators, having different cross-sectional shapes were solved. Findings. Authors have developed the method of calculation and obtained solutions for the determination of temperature fields in channels of the solid heat accumulator in conditions of convective heat transfer. Temperature fields over length and thickness of channels were investigated. Experimental studies on physical models and industrial equipment were conducted. Originality. For the first time the technique of calculating the temperature field in the channels of different cross-section for the solid heat accumulator in the charging and discharging modes was proposed. The calculation results are confirmed by experimental research. Practical value. The proposed technique is used in the design of solid heat accumulators of different power as well as full-scale production of them was organized.

  4. Spatial and temporal aspects of grain accumulation costs for ethanol production: An Australian case study

    International Nuclear Information System (INIS)

    Anderton, Nikki; Kingwell, Ross

    2008-01-01

    Ethanol production is increasingly commonplace in many grain-producing regions. This paper uses the grain-producing region of south-western Australia to illustrate spatial and temporal aspects of grain accumulation costs for ethanol production. Specifically, this study examines how price variability of various wheat grades, combined with spatial and temporal variability in production of those grades, affects the costs of grain accumulation. These costs are the main components of an ethanol plant's operating costs so lessening these costs can offer a comparative advantage for a plant owner. Logistics models based on mathematical programming are constructed for a range of plant sizes and locations for ethanol production. Modelling results identify low-cost sites that generate cost savings, in present value terms, of between 5 and 7.5 per cent, depending on plant size, over the 9-year study period. At all locations, small to medium-sized plants offer advantages of lower and less variable costs of grain accumulation. Yet, all locations and all plant sizes are characterised by marked volatility in the cost of grain accumulation. The profitability of ethanol production based on wheat in this region of Australia is particularly exposed to any prolonged period of high grain prices relative to petroleum prices, given current biofuel-policy settings in Australia. (author)

  5. Fostering triacylglycerol accumulation in novel oleaginous yeast Cryptococcus psychrotolerans IITRFD utilizing groundnut shell for improved biodiesel production.

    Science.gov (United States)

    Deeba, Farha; Pruthi, Vikas; Negi, Yuvraj S

    2017-10-01

    The investigation was carried out to examine the potential of triacylglycerol (TAG) accumulation by novel oleaginous yeast isolate Cryptococcus psychrotolerans IITRFD on utilizing groundnut shell acid hydrolysate (GSH) as cost-effective medium. The maximum biomass productivity and lipid productivity of 0.095±0.008g/L/h and 0.044±0.005g/L/h, respectively with lipid content 46% was recorded on GSH. Fatty acid methyl ester (FAME) profile obtained by GC-MS analysis revealed oleic acid (37.8%), palmitic (29.4%) and linoleic (32.8%) as major fatty acids representing balance between oxidative stability (OS) and cold flow filter properties (CFFP) for improved biodiesel quality. The biodiesel property calculated were correlated well with the fuel standards limits of ASTM D6751, EN 14214 and IS 15607. The present findings raise the possibility of using agricultural waste groundnut shell as a substrate for production of biodiesel by novel oleaginous yeast isolate C. psychrotolerans IITRFD. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Calculated apparent yields of rare gas fission products

    International Nuclear Information System (INIS)

    Delucchi, A.A.

    1975-01-01

    The apparent fission yield of the rare gas fission products from four mass chains is calculated as a function of separation time for six different fissioning systems. A plot of the calculated fission yield along with a one standard deviation error band is given for each rare gas fission product and for each fissioning system. Those parameters in the calculation that were major contributors to the calculated standard deviation at each separation time were identified and the results presented on a separate plot. To extend the usefulness of these calculations as new and better values for the input parameters become available, a third plot was generated for each system which shows how sensitive the derived fission yield is to a change in any given parameter used in the calculation. (U.S.)

  7. Analytical calculation of heavy quarkonia production processes in computer

    International Nuclear Information System (INIS)

    Braguta, V V; Likhoded, A K; Luchinsky, A V; Poslavsky, S V

    2014-01-01

    This report is devoted to the analytical calculation of heavy quarkonia production processes in modern experiments such as LHC, B-factories and superB-factories in computer. Theoretical description of heavy quarkonia is based on the factorization theorem. This theorem leads to special structure of the production amplitudes which can be used to develop computer algorithm which calculates these amplitudes automatically. This report is devoted to the description of this algorithm. As an example of its application we present the results of the calculation of double charmonia production in bottomonia decays and inclusive the χ cJ mesons production in pp-collisions

  8. Effect of sodium accumulation on heterotrophic growth and polyhydroxybutyrate (PHB) production by Cupriavidus necator.

    Science.gov (United States)

    Mozumder, Md Salatul Islam; Garcia-Gonzalez, Linsey; De Wever, Heleen; Volcke, Eveline I P

    2015-09-01

    This study evaluates the effect of sodium (Na(+)) concentration on the growth and PHB production by Cupriavidus necator. Both biomass growth and PHB production were inhibited by Na(+): biomass growth became zero at 8.9 g/L Na(+) concentration while PHB production was completely stopped at 10.5 g/L Na(+). A mathematical model for pure culture heterotrophic PHB production was set up to describe the Na(+) inhibition effect. The parameters related to Na(+) inhibition were estimated based on shake flask experiments. The accumulated Na(+) showed non-linear inhibition effect on biomass growth but linear inhibition effect on PHB production kinetics. Fed-batch experiments revealed that a high accumulation of Na(+) due to a prolonged growth phase, using NaOH for pH control, decreased the subsequent PHB production. The model was validated based on independent experimental data sets, showing a good agreement between experimental data and simulation results. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Production of biodegradable plastic by polyhydroxybutyrate (PHB) accumulating bacteria using low cost agricultural waste material.

    Science.gov (United States)

    Getachew, Anteneh; Woldesenbet, Fantahun

    2016-12-12

    Polyhydroxybutyrates (PHBs) are macromolecules synthesized by bacteria. They are inclusion bodies accumulated as reserve materials when the bacteria grow under different stress conditions. Because of their fast degradability under natural environmental conditions, PHBs are selected as alternatives for production of biodegradable plastics. The aim of this work was to isolate potential PHB producing bacteria, evaluate PHB production using agro-residues as carbon sources. Among fifty bacterial strains isolated from different localities, ten PHB accumulating strains were selected and compared for their ability to accumulate PHB granules inside their cells. Isolate Arba Minch Waste Water (AWW) identified as Bacillus spp was found to be the best producer. The optimum pH, temperature, and incubation period for best PHB production by the isolate were 7, 37 °C, and 48 h respectively at 150 rpm. PHB production was best with glucose as carbon source and peptone as nitrogen source. The strain was able to accumulate 55.6, 51.6, 37.4 and 25% PHB when pretreated sugar cane bagasse, corn cob, teff straw (Eragrostis tef) and banana peel were used as carbon sources respectively. Fourier transform-infrared authentication results of the extracted and purified PHB identified its functional units as C-H, CH 2 , C=O and C-O groups. UV-Vis spectrophotometric analysis and biodegradability test confirmed the similarity of the extract with standard PHB and its suitability for bioplastic production. The isolated Bacillus sp can be used for feasible production of PHB using agro-residues especially sugarcane bagasse which can reduce the production cost in addition to reducing the disposal problem of these substrates. The yield of PHB can further be boosted by optimization of production parameters as substrates.

  10. Accumulation of advanced glycation end (AGEs products in intensive care patients: an observational, prospective study

    Directory of Open Access Journals (Sweden)

    Rommes Johannes H

    2010-05-01

    Full Text Available Abstract Background Oxidative stress plays an important role in the course and eventual outcome in a majority of patients admitted to the intensive care unit (ICU. Markers to estimate oxidative stress are not readily available in a clinical setting. AGEs accumulation has been merely described in chronic conditions, but can also occur acutely due to oxidative stress. Since AGEs have emerged to be stable end products, these can be a marker of oxidative stress. Skin autofluorescence (AF is a validated marker of tissue content of AGEs. We hypothesized that AGEs accumulate acutely in ICU patients. Methods We performed an observational prospective study in a medical surgical ICU in a university affiliated teaching hospital. All consecutively admitted ICU patients in a 2 month period were included. Skin AF was measured using an AGE reader in 35 consecutive ICU patients > 18 yrs. As a comparison, historical data of a control group (n = 231 were used. These were also used to calculate age-adjusted AF-levels (AFadj. Values are expressed as median and interquartile range [P25-P75]. Differences between groups were tested by non parametric tests. P Results AFadj values were higher in ICU patients (0.33 [0.00 - 0.68] than in controls (-0.07 [-0.29 - 0.24]; P adj were observed between acute or planned admissions, or presence of sepsis, nor was skin AFadj related to severity of disease as estimated by APACHE-II score, length of ICU, hospital stay or mortality. Conclusion Acute AGE accumulation in ICU patients was shown in this study, although group size was small. This can possibly reflect oxidative stress in ICU patients. Further studies should reveal whether AGE-accumulation will be a useful parameter in ICU patients and whether skin AF has a predictive value for outcome, which was not shown in this small study.

  11. Accumulation of Long-lived activity in heavy metal liquid targets

    International Nuclear Information System (INIS)

    Shubin, Y. N.; Gai, E. V.; Ignatyuk, A. V.; Lunev, V. P.

    1997-01-01

    The calculations and analysis of the accumulation of radioactive nuclei and long-lived activity in heavy metal liquid targets were performed. The dominating contributions to the total radioactivity of radionuclides resulting from fission, spallation reactions and radiative capture by target nuclei for various irradiation and cooling times were calculated and analyzed. The most important parts of neutron and proton spectra were determined that give the dominant contributions to the total and partial activity of the targets. The contributions of fission products to the target activity and partial activities of main long-lived fission products were evaluated. The results of the calculations are compared with the data on Energy Amplifier Project. (Author) 12 refs

  12. An examination on the correction of attenuation for calculating the renal RI accumulation

    International Nuclear Information System (INIS)

    Onoue, Koichi; Tachibana, Keizo; Maeda, Yoshihiro; Yanoo, Sanae; Morishita, Etsuko; Kawanaka, Masahiro; Kashiwagi, Toru; Fukuchi, Minoru

    1999-01-01

    An examination was made on the attenuation coefficients for calculation of true renal accumulation rate together with the precision of measurement of depth in the kidney. Kidney phantom for attenuation coefficients was a 20 x 20 cm cube where water was filled and radioactivity source of 99m Tc was placed at various depths. Radioactivity was measured by four kinds of scinti-camera with the collimator LEGP and LEHR. The phantom for radioactivity accumulation in the kidney was a 10 x 5 x 1, 3 or 5 cm box where 99m Tc solution of the standard 30 MBq was filled, and subjected to radioactivity measurement from various angles. Phantom radioactivity was found corrected by the effective attenuation coefficient, 0.131 cm, within the range of 98-114% of the standard counts. The precision of measurement of the depth was examined in sideways scintigrams obtained in clinical practice and was found to have the deviation of 1.1 cm as the mean of maximum ones and the variation coefficient of 7.1%. Measured depth was found to be well correlated with estimated ones by the method of Tonnesen or Ito which had the maximum deviation of 5.4 or 3.5 cm, respectively. (K.H.)

  13. Large fragment production calculations in relativistic heavy-ion reactions

    International Nuclear Information System (INIS)

    Seixas de Oliveira, L.F.

    1978-12-01

    The abrasion-ablation model is briefly described and then used to calculate cross sections for production of large fragments resulting from target or projectile fragmentation in high-energy heavy-ion collisions. The number of nucleons removed from the colliding nuclei in the abrasion stage and the excitation energy of the remaining fragments (primary products) are calculated with the geometrical picture of two different models: the fireball and the firestreak models. The charge-to-mass dispersion of the primary products is calculated using either a model which assumes no correlations between proton and neutron positions inside the nucleus (hypergeometric distribution) or a model based upon the zero-point oscillations of the giant dipole resonance (NUC-GDR). Standard Weisskopf--Ewing statistical evaporation calculations are used to calculate final product distributions. Results of the pure abrasion-ablation model are compared with a variety of experimental data. The comparisons show the insufficiency of the extra-surface energy term used in the abrasion calculations. A frictional spectator interaction (FSI) is introduced which increases the average excitation energy of the primary products, and improves the results considerably in most cases. Agreements and discrepancies of the results calculated with the different theoretical assumptions and the experimental data are studied. Of particular relevance is the possibility of observing nuclear ground-state correlations.Results of the recently completed experiment of fragmentation of 213 Mev/A 40 Ar projectiles are studied and shown not to be capable of answering that question unambiguously. But predictions for the upcoming 48 Ca fragmentation experiment clearly show the possibility of observing correlation effects. 78 references

  14. Effect of collagen turnover on the accumulation of advanced glycation end products

    NARCIS (Netherlands)

    Verzijl, N.; Degroot, J.; Thorpe, S. R.; Bank, R. A.; Shaw, J. N.; Lyons, T. J.; Bijlsma, J. W.; Lafeber, F. P.; Baynes, J. W.; TeKoppele, J. M.

    2000-01-01

    Collagen molecules in articular cartilage have an exceptionally long lifetime, which makes them susceptible to the accumulation of advanced glycation end products (AGEs). In fact, in comparison to other collagen-rich tissues, articular cartilage contains relatively high amounts of the AGE

  15. Accumulation of lipid peroxidation products in eye structures of mice subjected to whole-body X-irradiation

    International Nuclear Information System (INIS)

    Sakina, N.L.; Dontsov, A.E.; Afanas'ev, G.G.; Ostrovskij, M.A.; Pelevina, I.I.

    1990-01-01

    In studying the effect of whole-body X-irradiation on the accumulation of lipid peroxidation products (conjugated dienes, TBA-active products, and Sciff bases) in retina and retinal pigmented epithelium of pigmented and nonpigmented mice it was shown that irradiation of dark-pigmented mice does not cause even a slight accumulation of lipid peroxidation products as compared to that in the controls. Albino mice exhibited a marked increase in the level of lipid peroxidation products which was manifested soon after irradiation and persisted for at least 3 months after irradiation. Melanine is suggested to participate in protecting eye structures against pro-oxidizing action of ionizing radiation

  16. Characteristic of nitrous oxide production in partial denitrification process with high nitrite accumulation.

    Science.gov (United States)

    Du, Rui; Peng, Yongzhen; Cao, Shenbin; Wang, Shuying; Niu, Meng

    2016-03-01

    Nitrous oxide (N2O) production during the partial denitrification process with nitrate (NO3(-)-N) to nitrite (NO2(-)-N) transformation ratio of 80% was investigated in this study. Results showed that N2O was seldom observed before complete depletion of NO3(-)-N, but it was closely related to the reduction of NO2(-)-N rather than NO3(-)-N. High COD/NO3(-)-N was in favor of N2O production in partial denitrification with high NO2(-)-N accumulation. It was seriously enhanced at constant acidic pH due to the free nitrous acid (FNA) inhibition. However, the N2O production was much lower at initial pH of 5.5 and 6.5 due to the pH increase during denitrification process. Significantly, the pH turning point could be chosen as a controlled parameter to denote the end of NO3(-)-N reduction, which could not only achieve high NO2(-)-N accumulation but also decrease the N2O production significantly for practical application. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Age-related accumulation of Maillard reaction products in human articular cartilage collagen

    NARCIS (Netherlands)

    Verzijl, N.; Degroot, J.; Oldehinkel, E.; Bank, R. A.; Thorpe, S. R.; Baynes, J. W.; Bayliss, M. T.; Bijlsma, J. W.; Lafeber, F. P.; TeKoppele, J. M.

    2000-01-01

    Non-enzymic modification of tissue proteins by reducing sugars, the so-called Maillard reaction, is a prominent feature of aging. In articular cartilage, relatively high levels of the advanced glycation end product (AGE) pentosidine accumulate with age. Higher pentosidine levels have been associated

  18. Map of calculated radioactivity of fission product, (4)

    International Nuclear Information System (INIS)

    Takeda, Tsuneo

    1978-07-01

    The overall radioactivities of fission products depending on irradiation time and cooling time were calculated for 18 different neutron fluxes, which are presented in contour maps and tables. Irradiation condition etc. are the followings: neutron flux (n sub(th)) 1 x 10 12 - 6.8 x 10 14 n/cm 2 /sec, uranium quantity 1 mole (6 x 10 23 atoms, ca. 271 g UO 2 ), U-235 enrichment 2.7%, irradiation time 60. - 6 x 10 7 sec (1 min - 1.9 y), cooling time 0. and 60. - 6 x 10 7 sec (1 min - 1.9 y). The enrichment value represents those for LWRs. To calculate the overall radioactivities, 595 fission product nuclides were introduced. Overall radioactivities calculations were made for 68,000 combinations of irradiation time, cooling time and neutron flux. The many complex decay chains of fission products were treated with CODAC-No.6 computer code. (author)

  19. User's manual for the radioactive decay and accumulation code RADAC

    International Nuclear Information System (INIS)

    Salmon, R.; Loghry, S.L.; Ashline, R.C.

    1995-11-01

    The RADAC computer code calculates radioactive decay and accumulation of decayed products using an algorithm based on the direct use of the Bateman equations and referred to here as the yield factor method. This report explains the yield factor method, gives an overview of the various modules in the RADAC code system, and describes the decay and accumulation code in detail. The RADAC code has capacity for two waste types and can accommodate up to 60 years of annual waste inputs. Decay times as high as 1 million years can be calculated. The user supplies the undecayed composition and radioactivity of the waste placed in storage each year. The code calculates the decayed composition, radioactivity, and thermal power of the accumulated waste at the end of each year and gives the results in terms of grams and curies of individual radionuclides. Calculations can be made for up to 19 waste storage sites in a single run. For each site and each waste type, calculations can be made by 1-year steps up to 60 years, by 10-year steps to 160 years, and by 6 discrete steps to 1 million years. Detailed outputs can be printed for each waste site and each time step by individual radionuclides. Summarized outputs are also available. Excluding data-preparation time, RADAC requires about 2 min to run 19 waste sites with two types of transuranic waste at each site, using a 486 DX computer with a clock speed of 33 MHz. Because RADAC uses a preselected set of decay times and does not make in-reactor calculations, it should not be viewed as a substitute for ORIGEN2. RADAC is intended for use in applications in which accumulations at the decay times provided by the code are sufficient for the user's purposes

  20. Denitrifying bacterial communities affect current production and nitrous oxide accumulation in a microbial fuel cell.

    Science.gov (United States)

    Vilar-Sanz, Ariadna; Puig, Sebastià; García-Lledó, Arantzazu; Trias, Rosalia; Balaguer, M Dolors; Colprim, Jesús; Bañeras, Lluís

    2013-01-01

    The biocathodic reduction of nitrate in Microbial Fuel Cells (MFCs) is an alternative to remove nitrogen in low carbon to nitrogen wastewater and relies entirely on microbial activity. In this paper the community composition of denitrifiers in the cathode of a MFC is analysed in relation to added electron acceptors (nitrate and nitrite) and organic matter in the cathode. Nitrate reducers and nitrite reducers were highly affected by the operational conditions and displayed high diversity. The number of retrieved species-level Operational Taxonomic Units (OTUs) for narG, napA, nirS and nirK genes was 11, 10, 31 and 22, respectively. In contrast, nitrous oxide reducers remained virtually unchanged at all conditions. About 90% of the retrieved nosZ sequences grouped in a single OTU with a high similarity with Oligotropha carboxidovorans nosZ gene. nirS-containing denitrifiers were dominant at all conditions and accounted for a significant amount of the total bacterial density. Current production decreased from 15.0 A · m(-3) NCC (Net Cathodic Compartment), when nitrate was used as an electron acceptor, to 14.1 A · m(-3) NCC in the case of nitrite. Contrarily, nitrous oxide (N2O) accumulation in the MFC was higher when nitrite was used as the main electron acceptor and accounted for 70% of gaseous nitrogen. Relative abundance of nitrite to nitrous oxide reducers, calculated as (qnirS+qnirK)/qnosZ, correlated positively with N2O emissions. Collectively, data indicate that bacteria catalysing the initial denitrification steps in a MFC are highly influenced by main electron acceptors and have a major influence on current production and N2O accumulation.

  1. Study on the calculation method of source term from fission products

    International Nuclear Information System (INIS)

    Zhou Jing; Gong Quan; Qiu Haifeng

    2014-01-01

    As a major part of radioactive nuclides, fission products play an important role in nuclear power plant design. The paper analyzes the calculation model of core activity inventory, the model of fission products releasing from the pellets to RCS, the balance model of fission products in RCS, and then proves them by calculation of the typical pressurized water reactor. The model is proved applicable for calculating fission products of pressurized water reactors. (authors)

  2. Quantum-mechanical calculation of carrier distribution in MOS accumulation and strong inversion layers

    Directory of Open Access Journals (Sweden)

    Chien-Wei Lee

    2013-10-01

    Full Text Available We derive a statistical physics model of two-dimensional electron gas (2DEG and propose an accurate approximation method for calculating the quantum-mechanical effects of metal-oxide-semiconductor (MOS structure in accumulation and strong inversion regions. We use an exponential surface potential approximation in solving the quantization energy levels and derive the function of density of states in 2D to 3D transition region by applying uncertainty principle and Schrödinger equation in k-space. The simulation results show that our approximation method and theory of density of states solve the two major problems of previous researches: the non-negligible error caused by the linear potential approximation and the inconsistency of density of states and carrier distribution in 2D to 3D transition region.

  3. Lipid accumulation product and triglycerides/glucose index are useful predictors of insulin resistance.

    Science.gov (United States)

    Mazidi, Mohsen; Kengne, Andre-Pascal; Katsiki, Niki; Mikhailidis, Dimitri P; Banach, Maciej

    2018-03-01

    To investigate the association of triglycerides/glucose index (TyG index), anthropometrically predicted visceral adipose tissue (apVAT), lipid accumulation product (LAP), visceral adiposity index (VAI) and triglycerides (TG):high density lipoprotein-cholesterol (HDL-C) ratio with insulin resistance (IR) in adult Americans. This study was based on data from three NHANES cycles (2005 to 2010). The TyG index was calculated as ln [TG×fasting glucose/2]. VAI was calculated using gender-specific formulas: men [waist circumference (WC)/39.68+(1.88×body mass index (BMI)]×(TG/1.03)×(1.31/HDL-C); women: [WC/36.58+(1.89×BMI)]×(TG/0.81)×(1.52/HDL-C). LAP index was calculated as [WC-65]×[TG] in men, and [WC-58]×[TG] in women. Correlation and regression analyses accounted for the complex sampling of database. A total of 18,318 subjects was included in this analysis [mean age 47.6Years]; 48.7% (n=8918) men]. The homeostatic model assessment of insulin resistance (HOMA-IR) had a significant positive correlation with the TyG index (r=0.502), LAP (r=0.551), apVAT (r=0.454), TG:HDL-C ratio (r=0.441) and VAI (r=451) (pindex is a simple, cheap and accurate although not perfect, surrogate marker of HOMA-diagnosed IR among adult Americans. Moreover, it has higher predictability than other screening tools which traditionally applied. Among the markers, apVAT had the highest specificity and the TG:HDL-C ratio had the highest sensitivity. Copyright © 2017 Elsevier Inc. All rights reserved.

  4. Impacts of damage production and accumulation on materials performance in irradiation environment

    DEFF Research Database (Denmark)

    Singh, B.N.

    1998-01-01

    and needs to be extended to temperatures below stage V and to materials of practical interests. This requires, however, that the information regarding the effects of alloying elements and impurity atoms on the nature of the primary damage state are available from molecular dynamics and kinetic Monte Carlo...... the damage accumulation, irradiation hardening and the loss of ductility. The recently developed production bias model together with one-dimensional glide of interstitial clusters produced in the cascades has been shown to describe the damage accumulation at temperatures above stage V for pure metals...... type of simulations. (C) 1998 Elsevier Science B.V. All rights reserved....

  5. Accumulation of nitrogen - a critical parameter for the calculation of load limits from nitrogen in forests; Akkumulering av nitrogen - en kritisk parameter for beregning av taalegrenser for nitrogen i skog

    Energy Technology Data Exchange (ETDEWEB)

    Sogn, T A; Stuanes, A O; Abrahamsen, G

    1996-01-01

    The conference paper deals with the accumulation of nitrogen in forests in Norway. The level of accumulation is a critical factor for the calculation of load limits. The paper compares the average rapidity values of accumulation since the last glacial age with the calculated values from the more short-lasting period based on data from surveying programs of the State Pollution Control Authority, manuring experiments, and other relevant research programs in this field. 8 refs., 1 fig., 1 tab.

  6. FABGEN, a transient power-generation and isotope birth rate calculator

    International Nuclear Information System (INIS)

    Roland, H.C.

    1975-04-01

    A description is given of the FABGEN program, a fast-running program for calculating fuel element power-generation rates and selected fission product birth rates in a known neutron flux as functions of time. A first forward difference calculation is used, and the time step is one day. Provisions are made for including various fuel element lengths, variation of thermal flux with time, and use of different fertile isotopes. Five different fission products may be specified for birth-rate calculations. A daily summary may be output, or totals by days may be accumulated for final output. (U.S.)

  7. Modeling chemical accumulation in sediment of small waterbodies accounting for sediment transport and water-sediment exchange processes over long periods.

    Science.gov (United States)

    Patterson, David Albert; Strehmel, Alexander; Erzgräber, Beate; Hammel, Klaus

    2017-12-01

    In a recent scientific opinion of the European Food Safety Authority it is argued that the accumulation of plant protection products in sediments over long time periods may be an environmentally significant process. Therefore, the European Food Safety Authority proposed a calculation to account for plant protection product accumulation. This calculation, however, considers plant protection product degradation within sediment as the only dissipation route, and does not account for sediment dynamics or back-diffusion into the water column. The hydraulic model Hydrologic Engineering Center-River Analysis System (HEC-RAS; US Army Corps of Engineers) was parameterized to assess sediment transport and deposition dynamics within the FOrum for Co-ordination of pesticide fate models and their USe (FOCUS) scenarios in simulations spanning 20 yr. The results show that only 10 to 50% of incoming sediment would be deposited. The remaining portion of sediment particles is transported across the downstream boundary. For a generic plant protection product substance this resulted in deposition of only 20 to 50% of incoming plant protection product substance. In a separate analysis, the FOCUS TOXSWA model was utilized to examine the relative importance of degradation versus back-diffusion as loss processes from the sediment compartment for a diverse range of generic plant protection products. In simulations spanning 20 yr, it was shown that back-diffusion was generally the dominant dissipation process. The results of the present study show that sediment dynamics and back-diffusion should be considered when calculating long-term plant protection product accumulation in sediment. Neglecting these may lead to a systematic overestimation of accumulation. Environ Toxicol Chem 2017;36:3223-3231. © 2017 SETAC. © 2017 SETAC.

  8. Accurate evaluation of subband structure in a carrier accumulation layer at an n-type InAs surface: LDF calculation combined with high-resolution photoelectron spectroscopy

    Directory of Open Access Journals (Sweden)

    Takeshi Inaoka

    2012-12-01

    Full Text Available Adsorption on an n-type InAs surface often induces a gradual formation of a carrier-accumulation layer at the surface. By means of high-resolution photoelectron spectroscopy (PES, Betti et al. made a systematic observation of subbands in the accumulation layer in the formation process. Incorporating a highly nonparabolic (NP dispersion of the conduction band into the local-density-functional (LDF formalism, we examine the subband structure in the accumulation-layer formation process. Combining the LDF calculation with the PES experiment, we make an accurate evaluation of the accumulated-carrier density, the subband-edge energies, and the subband energy dispersion at each formation stage. Our theoretical calculation can reproduce the three observed subbands quantitatively. The subband dispersion, which deviates downward from that of the projected bulk conduction band with an increase in wave number, becomes significantly weaker in the formation process. Accurate evaluation of the NP subband dispersion at each formation stage is indispensable in making a quantitative analysis of collective electronic excitations and transport properties in the subbands.

  9. PRESTO: online calculation of carbon in harvested wood products

    Science.gov (United States)

    Coeli M. Hoover; Sarah J. Beukema; Donald C.E. Robinson; Katherine M. Kellock; Diana A. Abraham

    2014-01-01

    Carbon stored in harvested wood products is recognized under international carbon accounting protocols, and some crediting systems may permit the inclusion of harvested wood products when calculating carbon sequestration. For managers and landowners, however, estimating carbon stored in harvested wood products may be difficult. PRESTO (PRoduct EStimation Tool Online)...

  10. A strong association between lipid accumulation product and diabetes mellitus in japanese women and men.

    Science.gov (United States)

    Wakabayashi, Ichiro; Daimon, Takashi

    2014-01-01

    Lipid accumulation product (LAP) is a new continuous marker of lipid overaccumulation that predicts cardiovascular risk. The aim of this study was to determine the cutoff value for LAP and evaluate its usefulness. Using a database of results of health checkup examinations for 10,170 Japanese workers (35-40 years of age) conducted at their workplaces, the cutoff value for a high LAP was calculated by analyzing receiver-operating characteristic (ROC) curves for the relationships of LAP with hyperglycemia and diabetes. The cutoff value for LAP was 21.1 for women and 37.2 for men. The values were similar when calculated by analyzing the ROC curves for the relationships with hyperglycemia and diabetes. Using these cutoff values, the prevalence of a high LAP was calculated to be 23.7% in women and 28.8% in men. The odds ratio for diabetes in the subjects with vs. those without a high LAP, calculated after adjusting for age, smoking, alcohol consumption and regular exercise, was 19.09 (95% CI: 6.57-55.50) in women and 7.40 (95% CI: 5.10-10.75) in men. High odds ratios for hypertension (10.66 [95% CI: 7.77-14.63] in women and 7.31 [95% CI: 6.20-8.62] in men) were also obtained in the subjects with vs. those without a high LAP. Cutoff values for a high LAP in women and men were determined, and high odds ratios for diabetes and hypertension were obtained using the cutoff values for LAP. Further studies are needed to elucidate whether the proposed cutoff values are applicable to people of other ages, races and ethnicities.

  11. Calculation of displacement and helium production at the LAMPF irradiation facility

    International Nuclear Information System (INIS)

    Davidson, D.R.; Greenwood, L.R.; Sommer, W.F.; Wechsler, M.S.

    1984-01-01

    Differential and total displacement and helium production rates are calculated for copper irradiated by spallation neutrons and 760 MeV protons at LAMPF. The calculations are performed using the SPECTER and VNMTC computer codes, the latter being specially designed for spallation radiation damage calculations. For comparison, similar SPECTER calculations are also described for irradiation of copper in EBR-II and RTNS-II. The results indicate substantial contributions to the displacement and helium production rates due to neutrons in the high-energy tail (above 40 MeV) of the LAMPF spallation neutron spectrum. Still higher production rates are calculated for irradiations in the direct proton beam. These results will provide useful background information for research to be conducted at a new irradiation facility at LAMPF

  12. Application of dynamic pseudo fission products and actinides for accurate burnup calculations

    Energy Technology Data Exchange (ETDEWEB)

    Hoogenboom, J.E.; Leege, P.F.A. de [Technische Univ. Delft (Netherlands). Interfacultair Reactor Inst.; Kloosterman, J.L.

    1996-09-01

    The introduction of pseudo fission products for accurate fine-group spectrum calculations during burnup is discussed. The calculation of the density of the pseudo nuclides is done before each spectrum calculation from the actual densities and their cross sections of all nuclides to be lumped into a pseudo fission product. As there are also many actinides formed in the fuel during its life cycle, a pseudo actinide with fission cross section is also introduced. From a realistic burnup calculation it is demonstrated that only a few fission products and actinides need to be included explicitly in a spectrum calculation. All other fission products and actinides can be accurately represented in the pseudo nuclides. (author)

  13. HEINBE; the calculation program for helium production in beryllium under neutron irradiation

    International Nuclear Information System (INIS)

    Shimakawa, Satoshi; Ishitsuka, Etsuo; Sato, Minoru

    1992-11-01

    HEINBE is a program on personal computer for calculating helium production in beryllium under neutron irradiation. The program can also calculate the tritium production in beryllium. Considering many nuclear reactions and their multi-step reactions, helium and tritium productions in beryllium materials irradiated at fusion reactor or fission reactor may be calculated with high accuracy. The calculation method, user's manual, calculated examples and comparison with experimental data were described. This report also describes a neutronics simulation method to generate additional data on swelling of beryllium, 3,000-15,000 appm helium range, for end-of-life of the proposed design for fusion blanket of the ITER. The calculation results indicate that helium production for beryllium sample doped lithium by 50 days irradiation in the fission reactor, such as the JMTR, could be achieved to 2,000-8,000 appm. (author)

  14. Mini-review: The Morphology, Mineralogy and Microbiology of Accumulated Iron Corrosion Products

    Science.gov (United States)

    2014-03-11

    including the morphology, mineralogy , microbiology and the mecha- nisms for formation. Use of descriptive terms to denote specific iron corrosion product...RESPONSIBLE PERSON 19b. TELEPHONE NUMBER (Include area code) 11-03-2014 Journal Article Mini-review: the morphology, mineralogy and microbiology of...oxides/ hydroxides with a preponderance of α-FeOOH (goethite) and accumulation of metals. Bacteria, particularly iron-oxidizing and sulfatereducing

  15. Calculation of CWKB envelope in boson and fermion productions

    International Nuclear Information System (INIS)

    Biswas, S.; Chowdhury, I.

    2007-01-01

    We present the calculation of envelope of boson and of both low-and high-mass fermion production at the end of inflation when the coherently oscillating inflations decay into bosons and fermions. We consider three different models of inflation and use CWKB technique to calculate the envelope to understand the structure of resonance band formation. We observe that though low-mass fermion production is not effective in preheating because of Pauli blocking, it is quite probable for high-mass fermion to take part in pre heating. (author)

  16. Calculation of Complexity Costs – An Approach for Rationalizing a Product Program

    DEFF Research Database (Denmark)

    Hansen, Christian Lindschou; Mortensen, Niels Henrik; Hvam, Lars

    2012-01-01

    This paper proposes an operational method for rationalizing a product program based on the calculation of complexity costs. The method takes its starting point in the calculation of complexity costs on a product program level. This is done throughout the value chain ranging from component invento...... of a product program. These findings represent an improved decision basis for the planning of reactive and proactive initiatives of rationalizing a product program.......This paper proposes an operational method for rationalizing a product program based on the calculation of complexity costs. The method takes its starting point in the calculation of complexity costs on a product program level. This is done throughout the value chain ranging from component...... inventories at the factory sites, all the way to the distribution of finished goods from distribution centers to the customers. The method proposes a step-wise approach including the analysis, quantification and allocation of product program complexity costs by the means of identifying of a number...

  17. Computer program FPIP-REV calculates fission product inventory for U-235 fission

    Science.gov (United States)

    Brown, W. S.; Call, D. W.

    1967-01-01

    Computer program calculates fission product inventories and source strengths associated with the operation of U-235 fueled nuclear power reactor. It utilizes a fission-product nuclide library of 254 nuclides, and calculates the time dependent behavior of the fission product nuclides formed by fissioning of U-235.

  18. Gas production potential of disperse low-saturation hydrate accumulations in oceanic sediments

    International Nuclear Information System (INIS)

    Moridis, George J.; Sloan, E. Dendy

    2007-01-01

    In this paper, we evaluate the gas production potential of disperse, low-saturation (S H H hydrate-bearing sediments subject to depressurization-induced dissociation over a 10-year production period. We investigate the sensitivity of items (a)-(c) to the following hydraulic properties, reservoir conditions, and operational parameters: intrinsic permeability, porosity, pressure, temperature, hydrate saturation, and constant pressure at which the production well is kept. The results of this study indicate that, despite wide variations in the aforementioned parameters (covering the entire spectrum of such deposits), gas production is very limited, never exceeding a few thousand cubic meters of gas during the 10-year production period. Such low production volumes are orders of magnitude below commonly accepted standards of economic viability, and are further burdened with very unfavorable gas-to-water ratios. The unequivocal conclusion from this study is that disperse, low-S H hydrate accumulations in oceanic sediments are not promising targets for gas production by means of depressurization-induced dissociation, and resources for early hydrate exploitation should be focused elsewhere

  19. Calculation of Direct photon production in nuclear collisions

    CERN Document Server

    Cepila, J

    2012-01-01

    Prompt photons produced in a hard reaction are not expected to be accompanied by any final state interaction, either energy loss or absorption and one should not expect any nuclear effects at high pT . However, data from the PHENIX experiment indicates large-pT suppression in d+Au and central Au+Au collisions that cannot be accompanied by coherent phenomena. We propose a mechanism based on the energy sharing problem at large pT near the kinematic limit that is induced by multiple initial state interactions and that improves the agreement of calculations with PHENIX data. We calculate inclusive direct photon production cross sections in p+p collisions at RHIC and LHC energies using the color dipole approach without any additional parameter. Our predictions are in good agreement with the available data. Within the same framework, we calculate direct photon production rates in d+A and A+A collisions at RHIC energy. We also provide predictions for the same process in p+A collisions at LHC energy. Since the kinema...

  20. Calculation of CWKB envelope in boson and fermion productions

    Indian Academy of Sciences (India)

    Abstract. We present the calculation of envelope of boson and of both low- and high- mass fermion production at the end of inflation when the coherently oscillating inflatons decay into bosons and fermions. We consider three different models of inflation and use. CWKB technique to calculate the envelope to understand the ...

  1. Model for fission-product calculations

    International Nuclear Information System (INIS)

    Smith, A.B.

    1984-01-01

    Many fission-product cross sections remain unmeasurable thus considerable reliance must be placed upon calculational interpolation and extrapolation from the few available measured cross sections. The vehicle, particularly for the lighter fission products, is the conventional optical-statistical model. The applied goals generally are: capture cross sections to 7 to 10% accuracies and inelastic-scattering cross sections to 25 to 50%. Comparisons of recent evaluations and experimental results indicate that these goals too often are far from being met, particularly in the area of inelastic scattering, and some of the evaluated fission-product cross sections are simply physically unreasonable. It is difficult to avoid the conclusion that the models employed in many of the evaluations are inappropriate and/or inappropriately used. In order to alleviate the above unfortunate situations, a regional optical-statistical (OM) model was sought with the goal of quantitative prediction of the cross sections of the lighter-mass (Z = 30-51) fission products. The first step toward that goal was the establishment of a reliable experimental data base consisting of energy-averaged neutron total and differential-scattering cross sections. The second step was the deduction of a regional model from the experimental data. It was assumed that a spherical OM is appropriate: a reasonable and practical assumption. The resulting OM then was verified against the measured data base. Finally, the physical character of the regional model is examined

  2. Carbon footprint calculation of Finnish greenhouse products; Kasvihuonetuotteiden ilmastovaikutuslaskenta. Loppuraportti

    Energy Technology Data Exchange (ETDEWEB)

    Yrjaenaeinen, H.; Silvenius, F.; Kaukoranta, T.; Naekkilae, J.; Saerkkae, L.; Tuhkanen, E.-M.

    2013-02-01

    This report presents the results of climate impact calculations for five products produced in Finnish greenhouses: tomatoes, cucumbers, salad crops, tulips and Elatior begonias. The study employed 16 greenhouses for the investigation; two greenhouses each for the tulips and the begonias and four each for the tomatoes, cucumbers and salad crops. Based on these calculations a greenhouse gas calculator was developed for greenhouse cultivators. The calculator is available at internet in www.kauppapuutarhaliitto.fi {yields} hiilijalanjaelki. In terms of environmental impacts this study concentrated on the climate impacts of the investigated products, and the calculations were made for the most significant greenhouse gases: carbon dioxide, methane and nitrous oxide. The following processes were included in the system boundaries: plant growing, manufacturing of lime, fertilizers and pesticides, manufacturing and disposal of pots, carbon dioxide production, irrigation, lighting, thermal curtains and cooling systems, the production and use of electricity and heat energy, distribution of products by the growers, other transportation, end-of-life and recycling. Processes excluded from the study were: distribution by other actors, retail functions, the consumer stage, and maintenance and manufacturing of infrastructure. The study used MTT's calculation model for the climate impact of food products excluding distribution and retail processes. The greenhouses selected for the study had some variation in their energy profiles and growing seasons. In addition, scenarios were created for different energy sources by using the average figures from this study. Monthly energy consumption values were also obtained from a number of the greenhouses and these were used to assess the variations in climate impact for different seasons. According to the results of the study the use of energy is the most significant source of climate impact of greenhouse products. In the tomato farms the

  3. Calculating the mass distribution of heavy nucleus fission product by neutrons

    International Nuclear Information System (INIS)

    Gudkov, A.N.; Koldobskij, A.B.; Kolobashkin, V.M.; Semenova, E.V.

    1981-01-01

    The technique of calculating the fission product mass yields by neutrons which are necessary for performing nucleus physical calculations in designing nuclear reactor cores is considered. The technique is based on the approximation of fission product mass distribution over the whole mass range by five Gauss functions. New analytical expressions for determining energy weights of used gaussians are proposed. The results of comparison of experimental data with calculated values for fission product mass obtained for reference processes in the capacity of which the fission reactions are chosen: 233 U, 235 U fission by thermal neutrons, 232 Th, 233 U, 235 U, 238 U by fission spectrum neutrons and 14 MeV neutrons and for 232 Th fission reactions by 11 MeV neutrons and 238 U by 7.7 MeV neutrons. On the basis of the analysis of results obtained the conclusion is drawn on a good agreement of fission product mass yield calculation values obtained using recommended values of mass distribution parameters with experimental data [ru

  4. THERMAL CALCULATION FOR THE PRODUCTION OF VEGETABLES GREENHOUSE

    Directory of Open Access Journals (Sweden)

    Ancuţa JURCO

    2013-01-01

    Full Text Available This paper presents the calculation regarding thermic transmision through the closing elements made for a greenhouse designed for salat production, pea, spinach and cabbage, D.M. greenhouse type, with medium and large openings (12...30m having a light roof with spatial structure from bars and thin walls made from galvanized steel or aluminium and designed at the Technique University from Cluj-Napoca. The greenhouse opening is 15.90 m, the total lenght is 40.50m and 669.53 sqm surface with 643.95 sqm usable area. After analyzing the thermal calculations for the production of vegetables greenhouse show that the heat losses are insignificant, advantage is given by the light roof with spatial structure from bars and thin walls made from galvanized steel or aluminium.

  5. Calculation of displacement and helium production at the LAMPF irradiation facility

    International Nuclear Information System (INIS)

    Wechsler, M.S.; Davidson, D.R.; Sommer, W.F.; Greenwood, L.R.

    1985-01-01

    Differential and total displacement and helium-production rates are calculated for copper irradiated by spallation neutrons and 760-MeV protons at LAMPF. The calculations are performed using the SPECTOR and VNMTC computer codes, the latter being specially designed for spallation radiation-damage calculations. For comparison, similar SPECTER calculations are also described for irradiation of copper in the experimental breeder reactor (EBR-II) at the Argonne National Laboratory-West in Idaho, and in the rotating target neutron source (RTNS-II) at Lawrence Livermore Laboratory. The neutron energy spectra for LAMPF, EBR-II, and RTNS-II and the displacement and helium-production cross sections are shown

  6. Calculating Program for Decommissioning Work Productivity based on Decommissioning Activity Experience Data

    Energy Technology Data Exchange (ETDEWEB)

    Song, Chan-Ho; Park, Seung-Kook; Park, Hee-Seong; Moon, Jei-kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    KAERI is performing research to calculate a coefficient for decommissioning work unit productivity to calculate the estimated time decommissioning work and estimated cost based on decommissioning activity experience data for KRR-2. KAERI used to calculate the decommissioning cost and manage decommissioning activity experience data through systems such as the decommissioning information management system (DECOMMIS), Decommissioning Facility Characterization DB System (DEFACS), decommissioning work-unit productivity calculation system (DEWOCS). In particular, KAERI used to based data for calculating the decommissioning cost with the form of a code work breakdown structure (WBS) based on decommissioning activity experience data for KRR-2.. Defined WBS code used to each system for calculate decommissioning cost. In this paper, we developed a program that can calculate the decommissioning cost using the decommissioning experience of KRR-2, UCP, and other countries through the mapping of a similar target facility between NPP and KRR-2. This paper is organized as follows. Chapter 2 discusses the decommissioning work productivity calculation method, and the mapping method of the decommissioning target facility will be described in the calculating program for decommissioning work productivity. At KAERI, research on various decommissioning methodologies of domestic NPPs will be conducted in the near future. In particular, It is difficult to determine the cost of decommissioning because such as NPP facility have the number of variables, such as the material of the target facility decommissioning, size, radiographic conditions exist.

  7. Calculating Program for Decommissioning Work Productivity based on Decommissioning Activity Experience Data

    International Nuclear Information System (INIS)

    Song, Chan-Ho; Park, Seung-Kook; Park, Hee-Seong; Moon, Jei-kwon

    2014-01-01

    KAERI is performing research to calculate a coefficient for decommissioning work unit productivity to calculate the estimated time decommissioning work and estimated cost based on decommissioning activity experience data for KRR-2. KAERI used to calculate the decommissioning cost and manage decommissioning activity experience data through systems such as the decommissioning information management system (DECOMMIS), Decommissioning Facility Characterization DB System (DEFACS), decommissioning work-unit productivity calculation system (DEWOCS). In particular, KAERI used to based data for calculating the decommissioning cost with the form of a code work breakdown structure (WBS) based on decommissioning activity experience data for KRR-2.. Defined WBS code used to each system for calculate decommissioning cost. In this paper, we developed a program that can calculate the decommissioning cost using the decommissioning experience of KRR-2, UCP, and other countries through the mapping of a similar target facility between NPP and KRR-2. This paper is organized as follows. Chapter 2 discusses the decommissioning work productivity calculation method, and the mapping method of the decommissioning target facility will be described in the calculating program for decommissioning work productivity. At KAERI, research on various decommissioning methodologies of domestic NPPs will be conducted in the near future. In particular, It is difficult to determine the cost of decommissioning because such as NPP facility have the number of variables, such as the material of the target facility decommissioning, size, radiographic conditions exist

  8. Inactivation of dhaD and dhaK abolishes by-product accumulation during 1,3-propanediol production in Klebsiella pneumoniae.

    Science.gov (United States)

    Horng, Yu-Tze; Chang, Kai-Chih; Chou, Ta-Chung; Yu, Chung-Jen; Chien, Chih-Ching; Wei, Yu-Hong; Soo, Po-Chi

    2010-07-01

    1,3-Propanediol (1,3-PD) can be used for the industrial synthesis of a variety of compounds, including polyesters, polyethers, and polyurethanes. 1,3-PD is generated from petrochemical and microbial sources. 1,3-Propanediol is a typical product of glycerol fermentation, while acetate, lactate, 2,3-butanediol, and ethanol also accumulate during the process. Substrate and product inhibition limit the final concentration of 1,3-propanediol in the fermentation broth. It is impossible to increase the yield of 1,3-propanediol by using the traditional whole-cell fermentation process. In this study, dhaD and dhaK, the genes for glycerol dehydrogenase and dihydroxyacetone kinase, respectively, were inactivated by homologous recombination in Klebsiella pneumoniae. The dhaD/dhaK double mutant (designated TC100), selected from 5,000 single or double cross homologous recombination mutants, was confirmed as a double cross by using polymerase chain reaction. Analysis of the cell-free supernatant with high-performance liquid chromatography revealed elimination of lactate and 2,3-butanediol, as well as ethanol accumulation in TC100, compared with the wild-type strain. Furthermore, 1,3-propanediol productivity was increased in the TC100 strain expressing glycerol dehydratase and 1,3-PDO dehydrogenase regulated by the arabinose P(BAD) promoter. The genetic engineering and medium formulation approaches used here should aid in the separation of 1,3-propanediol from lactate, 2,3-butanediol, and ethanol and lead to increased production of 1,3-propanediol in Klebsiella pneumoniae.

  9. Alleviation of harmful effect in stillage reflux in food waste ethanol fermentation based on metabolic and side-product accumulation regulation.

    Science.gov (United States)

    Ma, Hongzhi; Yang, Jian; Jia, Yan; Wang, Qunhui; Ma, Xiaoyu; Sonomoto, Kenji

    2016-10-01

    Stillage reflux fermentation in food waste ethanol fermentation could reduce sewage discharge but exert a harmful effect because of side-product accumulation. In this study, regulation methods based on metabolic regulation and side-product alleviation were conducted. Result demonstrated that controlling the proper oxidation-reduction potential value (-150mV to -250mV) could reduce the harmful effect, improve ethanol yield by 21%, and reduce fermentation time by 20%. The methods of adding calcium carbonate to adjust the accumulated lactic acid showed that ethanol yield increased by 17.3%, and fermentation time decreased by 20%. The accumulated glyceal also shows that these two methods can reduce the harmful effect. Fermentation time lasted for seven times without effect, and metabolic regulation had a better effect than side-product regulation. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Fission product model for lattice calculation of high conversion boiling water reactor

    International Nuclear Information System (INIS)

    Iijima, S.; Yoshida, T.; Yamamoto, T.

    1988-01-01

    A high precision fission product model for boiling water reactor (BWR) lattice calculation was developed, which consists of 45 nuclides to be treated explicitly and one nonsaturating pseudo nuclide. This model is applied to a high conversion BWR lattice calculation code. From a study based on a three-energy-group calculation of fission product poisoning due to full fission products and explicitly treated nuclides, the multigroup capture cross sections and the effective fission yields of the pseudo nuclide are determined, which do not depend on fuel types or reactor operating conditions for a good approximation. Apart from nuclear data uncertainties, the model and the derived pseudo nuclide constants would predict the fission product reactivity within an error of 0.1% Δk at high burnup

  11. Cost calculation model concerning small-scale production of chips and split firewood

    International Nuclear Information System (INIS)

    Ryynaenen, S.; Naett, H.; Valkonen, J.

    1995-01-01

    The TTS-Institute's Forestry Department has developed a computer-based cost calculation model for the production of wood chips and split firewood. This development work was carried out in conjunction with the nation-wide BIOENERGY -research programme. The said calculation model eases and speeds up the calculation of unit costs and resource needs in harvesting systems for wood chips and split firewood. The model also enables the user to find out how changes in the productivity and costs bases of different harvesting chains influences the unit costs of the system as a whole. The undertaking was composed of the following parts: clarification and modification of productivity bases for application in the model as mathematical models, clarification of machine and device costs bases, designing of the structure and functions of the calculation model, construction and testing of the model's 0-version, model calculations concerning typical chains, review of calculation bases, and charting of development needs focusing on the model. The calculation model was developed to serve research needs, but with further development it could be useful as a tool in forestry and agricultural extension work, related schools and colleges, and in the hands of firewood producers. (author)

  12. Nuclear data for actinide production and depletion calculations

    International Nuclear Information System (INIS)

    Benjamin, R.W.

    1978-01-01

    The status of nuclear cross section data required for actinide depletion calculations in thermal reactors is summarized, and recommendations are made for future work. The primary fertile and fissile nuclides ( 232 Th, 233 U, 235 U, 238 U, and 239 Pu) are not reviewed. Nuclear data for the transactinium mass region are, with few exceptions, reasonably complete and adequate for current thermal-reactor depletion calculations. There is a real need, however, for well-documented reactor production studies to use as benchmarks for data testing. 3 figures, 6 tables

  13. Adiposity indicators lipid accumulation product and triglyceride-glucose index as alternate criteria for the diagnosis of metabolic obesity in adult

    OpenAIRE

    Mariya Tabassum; Md. Matiur Rahman; Miliva Mozaffor

    2018-01-01

    Metabolic obesity refers to the state of having metabolic syndrome irrespective of one’s BMI. This study was aimed to elucidate the lipid accumulation product and triglyceride-glucose index as simple and alternate criteria for the detecting metabolic obesity in adult. The study was conducted in 200 adult (age range: 19-45 years). According to lipid accumulation product and Triglyceride-glucose index, the prevalence of metabolic obesity was 54.0% and 53.5% respectively. With a cutoff value of ...

  14. D-stat culture for studying the metabolic shifts from oxidative metabolism to lipid accumulation and citric acid production in Yarrowia lipolytica.

    Science.gov (United States)

    Ochoa-Estopier, Abril; Guillouet, Stéphane E

    2014-01-20

    Lipid accumulation in oleaginous yeasts is triggered by nutrient imbalance in the culture medium between the carbon source in excess and the nitrogen source in limiting concentration. However Yarrowia lipolytica when cultivated on glucose as the sole carbon source, mainly produces citric acid upon nitrogen limitation over lipid accumulation (only 5-10% triacylglycerol). Therefore for developing bioprocess for the production of triacylglycerol from renewable carbon source as glucose it is of first importance to control this imbalance in order to avoid citric acid production during TAG accumulation. Using D-stat cultivation system, where the N/C was linearly decreased using a constant change rate we were able to identify the N/C ratio inducing TAG accumulation (0.085NmolCmol(-1)) and citric acid (0.021NmolCmol(-1)). We therefore demonstrated that it was possible to accumulate lipids without excretion citric acid as long as the N/C was within this indicated range. Moreover enzyme specific activities measurement during the D-stat indicated that ATP-citrate lyase, malic enzyme and acetyl-coA carboxylase were strongly induced at the onset of lipid accumulation and showed different patterns when citric acid was excreted. Our results give relevant information for future industrial bioprocess development concerning the production of lipids using renewable carbohydrate substrates as an alternative way to produce synthons for fuel or chemical industry. By controlling the N/C over the fermentation process on glucose Y. lipolytica can accumulate lipids without excreting citric acid. Copyright © 2013 Elsevier B.V. All rights reserved.

  15. Peatlands in Finland accumulate carbon more than the peat production and utilization liberates it

    International Nuclear Information System (INIS)

    Maentymaa, E.

    1997-01-01

    The peatlands in Finland bind more carbon dioxide then it is liberated into the air in peat combustion and production. Because the carbon accumulation into peatlands is higher than that of liberation, the peat deposits increase all the time in spite of peat economy. The emissions of methane, which is tens of times worse greenhouse gas then CO 2 , have decreased by 40 % due to forest drainage. Very small amounts of methane is released into the atmosphere from peat production sites. This is proven by the national SILMU research programme investigating the atmospheric changes

  16. In-Stream Sediment Dynamics for predicted environmental concentration calculations of plant protection products in the FOCUSSW Scenarios

    Science.gov (United States)

    Strehmel, Alexander; Erzgräber, Beate; Gottesbüren, Bernhard

    2016-04-01

    The exposure assessment for the EU registration procedure of plant protection products (PPP), which is based on the 'Forum for the co-ordination of pesticide fate models and their use' (FOCUS), currently considers only periods of 12-16 months for the exposure assessment in surface water bodies. However, in a recent scientific opinion of the European Food Safety Authority (EFSA) it is argued that in a multi-year exposure assessment, the accumulation of PPP substances in river sediment may be a relevant process. Therefore, the EFSA proposed to introduce a sediment accumulation factor in order to account for enrichment of PPP substances over several years in the sediment. The calculation of this accumulation factor, however, would consider degradation in sediment as the only dissipation path, and does not take into account riverine sediment dynamics. In order to assess the influence of deposition and the possible extent of substance accumulation in the sediment phase, the hydraulic model HEC-RAS was employed for an assessment of in-stream sediment dynamics of the FOCUS stream scenarios. The model was parameterized according to the stream characteristics of the FOCUS scenarios and was run over a period of 20 years. The results show that with the distribution of grain sizes and the ranges of flow velocity in the FOCUS streams the main sediment process in the streams is transport. First modeling results suggest that about 80% of the eroded sediment mass from the adjacent field are transported to the downstream end of the stream and out of the system, while only about 20% are deposited in the river bed. At the same time, only about 30% of in-stream sediment mass stems from the adjacent field and is associated with PPP substance, while the remaining sediment consists of the substance-free base sediment concentration regarded in the scenarios. With this, the hydraulic modelling approach is able to support the development of a meaningful sediment accumulation factor by

  17. Technical note: Consistent calculation of aquatic gross production from oxygen triple isotope measurements

    Directory of Open Access Journals (Sweden)

    J. Kaiser

    2011-07-01

    Full Text Available Oxygen triple isotope measurements can be used to calculate aquatic gross oxygen production rates. Past studies have emphasised the appropriate definition of the 17O excess and often used an approximation to derive production rates from the 17O excess. Here, I show that the calculation can be phrased more consistently and without any approximations using the relative 17O/16O and 18O/16O isotope ratio differences (delta values directly. I call this the "dual delta method". The 17O excess is merely a mathematical construct and the derived production rate is independent of its definition, provided all calculations are performed with a consistent definition. I focus on the mixed layer, but also show how time series of triple isotope measurements below the mixed layer can be used to derive gross production.

    In the calculation of mixed layer productivity, I explicitly include isotopic fractionation during gas invasion and evasion, which requires the oxygen supersaturation s to be measured as well. I also suggest how bubble injection could be considered in the same mathematical framework. I distinguish between concentration steady state and isotopic steady state and show that only the latter needs to be assumed in the calculation. It is even possible to derive an estimate of the net production rate in the mixed layer that is independent of the assumption of concentration steady state.

    I review measurements of the parameters required for the calculation of gross production rates and show how their systematic uncertainties as well as the use of different published calculation methods can cause large variations in the production rates for the same underlying isotope ratios. In particular, the 17O excess of dissolved O2 in equilibrium with atmospheric O2 and the 17O excess of photosynthetic O2 need to

  18. Calculation of LUEC using HEEP Software for Nuclear Hydrogen Production Plant

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jongho; Lee, Kiyoung; Kim, Minhwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    To achieve the hydrogen economy, it is very important to produce a massive amount of hydrogen in a clean, safe and efficient way. Nuclear production of hydrogen would allow massive production of hydrogen at economic prices while avoiding environments pollution by reducing the release of carbon dioxide. A Very High Temperature Reactor (VHTR) is considered as an efficient reactor to couple with the thermo-chemical Sulfur Iodine (SI) cycle to achieve the hydrogen economy. HEEP(Hydrogen Economy Evaluation Program) is one of the software tools developed by IAEA to evaluate the economy of the nuclear hydrogen production system by estimating unit hydrogen production cost. In this paper, the LUHC (Levelized Unit Hydrogen Cost) is calculated by using HEEP for nuclear hydrogen production plant, which consists of 4 modules of 600 MWth VHTR coupled with SI process. The levelized unit hydrogen production cost(LUHC) was calculated by the HEEP software.

  19. Accumulation of the radionuclides in a target irradiated in the reactor of tajoura nuclear research center

    International Nuclear Information System (INIS)

    Abdunnobi, A.R.; Arebi, B.

    1998-01-01

    One of the main stages of radionuclides production in reactor is the distinguishing of a regime on target irradiation in order to acquire the sufficient activity and the purity of radioisotope required. The authors have derived formula for calculating radionuclidic accumulation on a target irradiated in the reactor operating 10 hours per day, 4 days a week during 4 weeks. The results of I-131 and other radionuclide accumulation are illustrated by a tellurium target irradiation in the reactor operating continuously or with interruptions

  20. Isotope Production Facility Conceptual Thermal-Hydraulic Design Review and Scoping Calculations

    International Nuclear Information System (INIS)

    Pasamehmetoglu, K.O.; Shelton, J.D.

    1998-01-01

    The thermal-hydraulic design of the target for the Isotope Production Facility (IPF) is reviewed. In support of the technical review, scoping calculations are performed. The results of the review and scoping calculations are presented in this report

  1. Sensitivity and uncertainty analysis for fission product decay heat calculations

    International Nuclear Information System (INIS)

    Rebah, J.; Lee, Y.K.; Nimal, J.C.; Nimal, B.; Luneville, L.; Duchemin, B.

    1994-01-01

    The calculated uncertainty in decay heat due to the uncertainty in basic nuclear data given in the CEA86 Library, is presented. Uncertainties in summation calculation arise from several sources: fission product yields, half-lives and average decay energies. The correlation between basic data is taken into account. The uncertainty analysis were obtained for thermal-neutron-induced fission of U235 and Pu239 in the case of burst fission and irradiation time. The calculated decay heat in this study is compared with experimental results and with new calculation using the JEF2 Library. (from authors) 6 figs., 19 refs

  2. SCALE Sensitivity Calculations Using Contributon Theory

    International Nuclear Information System (INIS)

    Rearden, Bradley T.; Perfetti, Chris; Williams, Mark L.; Petrie, Lester M. Jr.

    2010-01-01

    The SCALE TSUNAMI-3D sensitivity and uncertainty analysis sequence computes the sensitivity of k-eff to each constituent multigroup cross section using adjoint techniques with the KENO Monte Carlo codes. A new technique to simultaneously obtain the product of the forward and adjoint angular flux moments within a single Monte Carlo calculation has been developed and implemented in the SCALE TSUNAMI-3D analysis sequence. A new concept in Monte Carlo theory has been developed for this work, an eigenvalue contributon estimator, which is an extension of previously developed fixed-source contributon estimators. A contributon is a particle for which the forward solution is accumulated, and its importance to the response, which is equivalent to the adjoint solution, is simultaneously accumulated. Thus, the contributon is a particle coupled with its contribution to the response, in this case k-eff. As implemented in SCALE, the contributon provides the importance of a particle exiting at any energy or direction for each location, energy and direction at which the forward flux solution is sampled. Although currently implemented for eigenvalue calculations in multigroup mode in KENO, this technique is directly applicable to continuous-energy calculations for many other responses such as fixed-source sensitivity analysis and quantification of reactor kinetics parameters. This paper provides the physical bases of eigenvalue contributon theory, provides details of implementation into TSUNAMI-3D, and provides results of sample calculations.

  3. Timing and placement of cattle manure and/or gliricidia affects cotton and sunflower nutrient accumulation and biomass productivity.

    Science.gov (United States)

    Primo, Dário C; Menezes, Rômulo S C; Oliveira, Fabio F DE; Dubeux Júnior, José Carlos B; Sampaio, Everardo V S B

    2018-01-01

    Organic fertilizers are a viable alternative to increase oilseed productivity in family agriculture systems. The study aimed to evaluate the effects of timing and placement of cattle manure and/or gliricidia (Gliricidia sepium Jacq. Walp) prunings on cotton (Gossipium hirsutum L.) and sunflower (Helianthus annuus L.) nutrient accumulation and biomass productivity. Experiments were carried out in 2010 and 2011 in Taperoá, Paraíba, Brazil. The organic fertilization treatments were: GI - gliricidia incorporated before planting; GS - gliricidia applied on surface 45 days after planting (DAP); MI + GI - manure and gliricidia incorporated before planting; MI + GS - manure incorporated before planting and gliricídia applied on the surface 45 DAP; MI - manure incorporated before planting; and T - with no organic fertilization. In 2010, treatment MI + GS increased N, P, and K accumulation in cotton (12 and 7 kg ha-1) as well as in sunflower (20 and 29 kg ha-1). In 2011, GI and GS treatments resulted in higher N, P, K accumulations in both crops. The highest cotton productivity in 2010 was obtained with MI + GS treatment (198 kg ha-1) and in 2011 with GS treatment (594 kg ha-1). For sunflower, MI + GS treatment yielded the highest productivity in 2010 (466 kg ha-1) and GI treatment in 2011 (3542 kg ha-1). GI and MI + GS treatments increased total biomass productivity for cotton and sunflower. The treatment that combined both cattle manure incorporated into the soil before planting and gliricidia applied on the surface 45 days after planting was the most viable management strategy.

  4. An assessment of fission product data for decay power calculation in fast reactors

    International Nuclear Information System (INIS)

    Sridharan, M.S.; Murthy, K.P.N.

    1987-01-01

    A review of our present capability at IGC, Kalpakkam to predict fission product decay power in fast reactors is presented. This is accomplished by comparing our summation calculations with the calculations of others and the reported experimental measurements. Our calculations are based on Chandy code developed at our Centre. The fission product data base of Chandy is essentially drawn from the yield data compiled by Crouch (1977) and the data on halflives etc. compiled by Tobias (1973). In general, we find good agreement amongst the different calculations (within ±5%) and our calculations also compare well with experimental measurements of AKIAMA et al and MURPHY et al

  5. ELSA: A simplified code for fission product release calculations

    International Nuclear Information System (INIS)

    Manenc, H.; Notley, M.J.

    1996-01-01

    During a light water reactor severe accident, fission products are released from the overheated core as it progressively degrades. A new computer module named ELSA is being developed to calculate fission product release. The authors approach is to model the key phenomena, as opposed to more complete mechanistic approaches. Here they present the main features of the module. Different release mechanisms have been identified and are modeled in ELSA, depending on fission product volatility: diffusion seems to govern the release of the highly volatile species if fuel oxidation is properly accounted for, whereas mass transport governs that of lower volatility fission products and fuel volatilization that of the practically involatile species

  6. Balanced activation of IspG and IspH to eliminate MEP intermediate accumulation and improve isoprenoids production in Escherichia coli.

    Science.gov (United States)

    Li, Qingyan; Fan, Feiyu; Gao, Xiang; Yang, Chen; Bi, Changhao; Tang, Jinlei; Liu, Tao; Zhang, Xueli

    2017-11-01

    The MEP pathway genes were modulated to investigate whether there were new rate-limiting steps and toxic intermediates in this pathway. Activating IspG led to significant decrease of cell growth and β-carotene production. It was found that ispG overexpression led to accumulation of intermediate HMBPP, which seriously interfered with synthesis machinery of nucleotide and protein in Escherichia coli. Activation of the downstream enzyme IspH could solve HMBPP accumulation problem and eliminate the negative effects of ispG overexpression. In addition, intermediate MECPP accumulated in the starting strain, while balanced activation of IspG and IspH could push the carbon flux away from MECPP and led to 73% and 77% increase of β-carotene and lycopene titer respectively. Our work for the first time identified HMBPP to be a cytotoxic intermediate in MEP pathway and demonstrated that balanced activation of IspG and IspH could eliminate accumulation of HMBPP and MECPP and improve isoprenoids production. Copyright © 2017 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

  7. 19 CFR 351.407 - Calculation of constructed value and cost of production.

    Science.gov (United States)

    2010-04-01

    ... ANTIDUMPING AND COUNTERVAILING DUTIES Calculation of Export Price, Constructed Export Price, Fair Value, and Normal Value § 351.407 Calculation of constructed value and cost of production. (a) Introduction. This... 19 Customs Duties 3 2010-04-01 2010-04-01 false Calculation of constructed value and cost of...

  8. Rotator cuff tear reduces muscle fiber specific force production and induces macrophage accumulation and autophagy.

    Science.gov (United States)

    Gumucio, Jonathan P; Davis, Max E; Bradley, Joshua R; Stafford, Patrick L; Schiffman, Corey J; Lynch, Evan B; Claflin, Dennis R; Bedi, Asheesh; Mendias, Christopher L

    2012-12-01

    Full-thickness tears to the rotator cuff can cause severe pain and disability. Untreated tears progress in size and are associated with muscle atrophy and an infiltration of fat to the area, a condition known as "fatty degeneration." To improve the treatment of rotator cuff tears, a greater understanding of the changes in the contractile properties of muscle fibers and the molecular regulation of fatty degeneration is essential. Using a rat model of rotator cuff injury, we measured the force generating capacity of individual muscle fibers and determined changes in muscle fiber type distribution that develop after a full thickness rotator cuff tear. We also measured the expression of mRNA and miRNA transcripts involved in muscle atrophy, lipid accumulation, and matrix synthesis. We hypothesized that a decrease in specific force of rotator cuff muscle fibers, an accumulation of type IIb fibers, and an upregulation in fibrogenic, adipogenic, and inflammatory gene expression occur in torn rotator cuff muscles. Thirty days following rotator cuff tear, we observed a reduction in muscle fiber force production, an induction of fibrogenic, adipogenic, and autophagocytic mRNA and miRNA molecules, and a dramatic accumulation of macrophages in areas of fat accumulation. Copyright © 2012 Orthopaedic Research Society.

  9. [Characteristics of dry matter production and nitrogen accumulation in barley genotypes with high nitrogen utilization efficiency].

    Science.gov (United States)

    Huang, Yi; Li, Ting-Xuan; Zhang, Xi-Zhou; Ji, Lin

    2014-07-01

    A pot experiment was conducted under low (125 mg x kg-1) and normal (250 mg x kg(-1)) nitrogen treatments. The nitrogen uptake and utilization efficiency of 22 barley cultivars were investigated, and the characteristics of dry matter production and nitrogen accumulation in barley were analyzed. The results showed that nitrogen uptake and utilization efficiency were different for barley under two nitrogen levels. The maximal values of grain yield, nitrogen utilization efficiency for grain and nitrogen harvest index were 2.87, 2.91 and 2.47 times as those of the lowest under the low nitrogen treatment. Grain yield and nitrogen utilization efficiency for grain and nitrogen harvest index of barley genotype with high nitrogen utilization efficiency were significantly greater than low nitrogen utilization efficiency, and the parameters of high nitrogen utilization efficiency genotype were 82.1%, 61.5% and 50.5% higher than low nitrogen utilization efficiency genotype under the low nitrogen treatment. Dry matter mass and nitrogen utilization of high nitrogen utilization efficiency was significantly higher than those of low nitrogen utilization efficiency. A peak of dry matter mass of high nitrogen utilization efficiency occurred during jointing to heading stage, while that of nitrogen accumulation appeared before jointing. Under the low nitrogen treatment, dry matter mass of DH61 and DH121+ was 34.4% and 38.3%, and nitrogen accumulation was 54. 8% and 58.0% higher than DH80, respectively. Dry matter mass and nitrogen accumulation seriously affected yield before jointing stage, and the contribution rates were 47.9% and 54.7% respectively under the low nitrogen treatment. The effect of dry matter and nitrogen accumulation on nitrogen utilization efficiency for grain was the largest during heading to mature stages, followed by sowing to jointing stages, with the contribution rate being 29.5% and 48.7%, 29.0% and 15.8%, respectively. In conclusion, barley genotype with high

  10. Nuclear model calculations on cyclotron production of {sup 51}Cr

    Energy Technology Data Exchange (ETDEWEB)

    Kakavand, Tayeb [Imam Khomeini International Univ., Qazvin (Iran, Islamic Republic of). Dept. of Physics; Aboudzadeh, Mohammadreza [Nuclear Science and Technology Research Institute/AEOI, Karaj (Iran, Islamic Republic of). Agricultural, Medical and Industrial Research School; Farahani, Zahra; Eslami, Mohammad [Zanjan Univ. (Iran, Islamic Republic of). Dept. of Physics

    2015-12-15

    {sup 51}Cr (T{sub 1/2} = 27.7 d), which decays via electron capture (100 %) with 320 keV gamma emission (9.8 %), is a radionuclide with still a large application in biological studies. In this work, ALICE/ASH and TALYS nuclear model codes along with some adjustments are used to calculate the excitation functions for proton, deuteron, α-particle and neutron induced on various targets leading to the production of {sup 51}Cr radioisotope. The production yields of {sup 51}Cr from various reactions are determined using the excitation function calculations and stopping power data. The results are compared with corresponding experimental data and discussed from point of view of feasibility.

  11. Development and application of the PBMR fission product release calculation model

    International Nuclear Information System (INIS)

    Merwe, J.J. van der; Clifford, I.

    2008-01-01

    At PBMR, long-lived fission product release from spherical fuel spheres is calculated using the German legacy software product GETTER. GETTER is a good tool when performing calculations for fuel spheres under controlled operating conditions, including irradiation tests and post-irradiation heat-up experiments. It has proved itself as a versatile reactor analysis tool, but is rather cumbersome when used for accident and sensitivity analysis. Developments in depressurized loss of forced cooling (DLOFC) accident analysis using GETTER led to the creation of FIssion Product RElease under accident (X) conditions (FIPREX), and later FIPREX-GETTER. FIPREX-GETTER is designed as a wrapper around GETTER so that calculations can be carried out for large numbers of fuel spheres with design and operating parameters that can be stochastically varied. This allows full Monte Carlo sensitivity analyses to be performed for representative cores containing many fuel spheres. The development process and application of FIPREX-GETTER in reactor analysis at PBMR is explained and the requirements for future developments of the code are discussed. Results are presented for a sample PBMR core design under normal operating conditions as well as a suite of design-base accident events, illustrating the functionality of FIPREX-GETTER. Monte Carlo sensitivity analysis principles are explained and presented for each calculation type. The plan and current status of verification and validation (V and V) is described. This is an important and necessary process for all software and calculation model development at PBMR

  12. Risk factors for chronic transplant dysfunction and cardiovascular disease are related to accumulation of advanced glycation end-products in renal transplant recipients

    NARCIS (Netherlands)

    Hartog, Jasper W. L.; de Vries, Aiko P. J.; Bakker, Stephan J. L.; Graaff, Reindert; van Son, Willem J.; van der Heide, Jaap J. Homan; Gans, Reinold O. B.; Wolffenbuttel, Bruce H. R.; de Jong, Paul E.; Smit, Andries J.

    Background. Accumulation of advanced glycation end-products (AGEs) has been implicated in the pathogenesis of chronic transplant dysfunction and cardiovascular disease in renal transplant recipients. We aimed to investigate which factors are associated with tissue AGE accumulation in renal

  13. Risk factors for chronic transplant dysfunction and cardiovascular disease are related to accumulation of advanced glycation end-products in renal transplant recipients

    NARCIS (Netherlands)

    Hartog, Jasper W. L.; de Vries, Aiko P. J.; Bakker, Stephan J. L.; Graaff, Reindert; van Son, Willem J.; Homan van der Heide, Jaap J.; Gans, Reinold O. B.; Wolffenbuttel, Bruce H. R.; de Jong, Paul E.; Smit, Andries J.

    2006-01-01

    Accumulation of advanced glycation end-products (AGEs) has been implicated in the pathogenesis of chronic transplant dysfunction and cardiovascular disease in renal transplant recipients. We aimed to investigate which factors are associated with tissue AGE accumulation in renal transplant

  14. FISPRO: a simplified computer program for general fission product formation and decay calculations

    International Nuclear Information System (INIS)

    Jiacoletti, R.J.; Bailey, P.G.

    1979-08-01

    This report describes a computer program that solves a general form of the fission product formation and decay equations over given time steps for arbitrary decay chains composed of up to three nuclides. All fission product data and operational history data are input through user-defined input files. The program is very useful in the calculation of fission product activities of specific nuclides for various reactor operational histories and accident consequence calculations

  15. New Products and Technologies, Based on Calculations Developed Areas

    Directory of Open Access Journals (Sweden)

    Gheorghe Vertan

    2013-09-01

    Full Text Available Following statistics, currently prosperous and have high GDP / capita, only countries that have and fructify intensively large natural resources and/or produce and export products massive based on patented inventions accordingly. Without great natural wealth and the lowest GDP / capita in the EU, Romania will prosper only with such products. Starting from the top experience in the country, some patented, can develop new and competitive technologies and patentable and exportable products, based on exact calculations of developed areas, such as that double shells welded assemblies and plating of ships' propellers and blade pump and hydraulic turbines.

  16. Geochemistry Model Validation Report: External Accumulation Model

    International Nuclear Information System (INIS)

    Zarrabi, K.

    2001-01-01

    The purpose of this Analysis and Modeling Report (AMR) is to validate the External Accumulation Model that predicts accumulation of fissile materials in fractures and lithophysae in the rock beneath a degrading waste package (WP) in the potential monitored geologic repository at Yucca Mountain. (Lithophysae are voids in the rock having concentric shells of finely crystalline alkali feldspar, quartz, and other materials that were formed due to entrapped gas that later escaped, DOE 1998, p. A-25.) The intended use of this model is to estimate the quantities of external accumulation of fissile material for use in external criticality risk assessments for different types of degrading WPs: U.S. Department of Energy (DOE) Spent Nuclear Fuel (SNF) codisposed with High Level Waste (HLW) glass, commercial SNF, and Immobilized Plutonium Ceramic (Pu-ceramic) codisposed with HLW glass. The scope of the model validation is to (1) describe the model and the parameters used to develop the model, (2) provide rationale for selection of the parameters by comparisons with measured values, and (3) demonstrate that the parameters chosen are the most conservative selection for external criticality risk calculations. To demonstrate the applicability of the model, a Pu-ceramic WP is used as an example. The model begins with a source term from separately documented EQ6 calculations; where the source term is defined as the composition versus time of the water flowing out of a breached waste package (WP). Next, PHREEQC, is used to simulate the transport and interaction of the source term with the resident water and fractured tuff below the repository. In these simulations the primary mechanism for accumulation is mixing of the high pH, actinide-laden source term with resident water; thus lowering the pH values sufficiently for fissile minerals to become insoluble and precipitate. In the final section of the model, the outputs from PHREEQC, are processed to produce mass of accumulation

  17. Reactor calculations in aid of isotope production at SAFARI-1

    International Nuclear Information System (INIS)

    Ball, G.

    2003-01-01

    Varying levels of reactor physics support is given to the isotope production industry. As the pressures on both the safety limits and economical production of reactor produced isotopes mount, reactor physics calculational support is playing an ever increasing role. Detailed modelling of the reactor, irradiation rigs and target material enables isotope production in reactors to be maximised with respect to yields and quality. NECSA's methodology in this field is described and some examples are given. (author)

  18. Benchmark calculations on residue production within the EURISOL DS project; Part I: thin targets

    CERN Document Server

    David, J.C; Boudard, A; Doré, D; Leray, S; Rapp, B; Ridikas, D; Thiollière, N

    Report on benchmark calculations on residue production in thin targets. Calculations were performed using MCNPX 2.5.0 coupled to a selection of reaction models. The results were compared to nuclide production cross-sections measured in GSI in inverse kinematics

  19. An order αs Monte Carlo calculation of hadronic double photon production

    International Nuclear Information System (INIS)

    Owens, J.F.

    1992-01-01

    The results of an order α s calculation of hadronic double photon production are discussed and compared with data from both colliding beam and fixed target experiments. The calculation utilizes a combination of analytic and Monte Carlo integration methods which make it easy to calculate a variety of observables and impose experimental cuts. (author) 8 refs.; 2 figs

  20. STUDY OF STATIC ELECTRICITY CHARGE ACCUMULATION ON SURFACE OF FLUOROPOLYMER-4 PRODUCTS USING VIBRATING CAPACITOR METHOD

    Directory of Open Access Journals (Sweden)

    H. А. Vershina

    2012-01-01

    Full Text Available The paper presents investigations of processes pertaining to surface charge accumulation and running of fluoropolymer-4 products using vibrating capacitor method. Modification of a measurement technique allowing to register distribution of dielectric surface potential without disturbance of the surface charged state has been described in the paper. The paper contains graphics of spatial distribution of surface potential of fluoropolymer-4 products after various treatments. The paper reveals that thermal treatment (tempering reduces static characteristics of fluoropolymer-4.

  1. Influence of environmental parameters on production of the acrolein precursor 3-hydroxypropionaldehyde by Lactobacillus reuteri DSMZ 20016 and its accumulation by wine lactobacilli.

    Science.gov (United States)

    Bauer, Rolene; du Toit, Maret; Kossmann, Jens

    2010-01-31

    Lactic acid bacteria belonging to the genus Lactobacillus are known to convert glycerol into 3-hydroxypropionaldehyde (3-HPA) during anaerobic glycerol fermentation. Wine quality can be gravely compromised by the accumulation of 3-HPA, due to its spontaneous conversion to acrolein under wine making conditions. Acrolein is not only a dangerous substance for the living cell, but has been implicated in the development of unpleasant bitterness in beverages. This study evaluates the effect of individual environmental parameters on 3-HPA production by Lactobacillus reuteri DSMZ 20016, which only proved possible under conditions that allow accumulation well below the threshold concentration affecting cell viability. 3-HPA production was optimal at pH 6 and in the presence of 300 mM glycerol. Production increased with an increase in cell concentration up to an OD(600) of 50, whereas higher cell concentrations inhibited accumulation. Data presented in this study suggest that 3-HPA plays a role in regulating its own production through quorum sensing. Glycerol dehydratase possessing bacterial strains isolated from South African red wine, L. pentosus and L. brevis, tested positive for 3-HPA accumulation. 3-HPA is normally intracellularly reduced to 1,3-propanediol. This is the first study demonstrating the ability of wine lactobacilli to accumulate 3-HPA in the fermentation media. Recommendations are made on preventing the formation of acrolein and its precursor 3-HPA in wine. Copyright 2009 Elsevier B.V. All rights reserved.

  2. Mass formula dependence of calculated spallation reaction product distributions

    International Nuclear Information System (INIS)

    Nishida, Takahiko; Nakahara, Yasuaki

    1990-01-01

    A new version of the spallation reaction simulation code NUCLEUS was developed by incorporating Uno and Yamada's mass formula. This version was used to calculate the distribution of products from the spallation of uranium nuclei by high-energy protons. The dependence of the distributions on the mass formula was examined by comparing the results with those from the original version, which is based on Cameron's mass formula and the mass table compiled by Wapstra et al. As regards the fission component of spallation products, the new version reproduces the reaction product data obtained from thin foil experiments much better, especially on the neutron excess side. (orig.) [de

  3. Carbon accumulation in pristine and drained mires

    Energy Technology Data Exchange (ETDEWEB)

    Maekilae, M.

    2011-07-01

    The carbon accumulation of 73 peat columns from 48 pristine and drained mires was investigated using a total of 367 dates and age-depth models derived from bulk density measurements. Peat columns were collected from mires of varying depth, age, degree of natural state and nutrient conditions in aapa mire and raised bog regions and coastal mires from southern and central Finland and Russian Karelia. Particular attention was paid to the accumulation of carbon over the last 300 years, as this period encompasses the best estimates of the oxic layer (acrotelm) age across the range of sites investigated. In general, drained mires are initially more nutrient-rich than pristine mires. Organic matter decomposes more rapidly at drained sites than at pristine sites, resulting in thinner peat layers and carbon accumulation but a higher dry bulk density and carbon content. The average carbon accumulation was calculated as 24.0 g m-2 yr-1 at pristine sites and 19.4 g m-2 yr-1 at drained sites, while for peat layers younger than 300 years the respective figures were 45.3 and 34.5 g m-2 yr-1 at pristine and drained sites. For the <300-year-old peat layers studied here, the average thickness was 19 cm less and the carbon accumulation rate 10.8 g m-2 yr-1 lower in drained areas than in pristine areas. The amount carbon accumulation of surface peat layers depends upon the mire site type, vegetation and natural state; variations reflect differences in plant communities as well as factors that affect biomass production and decay rates. The highest accumulation rates and thus carbon binding for layers younger than 300 years were measured in the ombrotrophic mire site types (Sphagnum fuscum bog and Sphagnum fuscum pine bog), and the second highest rates in wet, treeless oligotrophic and minerotrophic mire site types. The lowest values of carbon accumulation over the last 300 years were obtained for the most transformed, sparsely forested and forested mire site types, where the water

  4. PROLIB: code to create production library of nuclear data for design calculations

    International Nuclear Information System (INIS)

    Wittkopf, W.A.; Tilford, J.M.; Furtney, M.

    1977-02-01

    The PROLIB program creates, updates, and edits the production library used in the B and W nuclear design system. The production library contains the material cross section data required to perform the thermal and epithermal spectrum calculations in the NULIF program. PROLIB collapses cross section data from the master libraries, produced by the ETOGM and THOR programs, to the desired production library group structures. The physics models that are used, the calculations that are performed in PROLIB, the input, and the output are described. Information that is required to use PROLIB along with a sample problem that illustrates the input and output formats and that provides a benchmark problem are given

  5. Calculations of pair production by Monte Carlo methods

    International Nuclear Information System (INIS)

    Bottcher, C.; Strayer, M.R.

    1991-01-01

    We describe some of the technical design issues associated with the production of particle-antiparticle pairs in very large accelerators. To answer these questions requires extensive calculation of Feynman diagrams, in effect multi-dimensional integrals, which we evaluate by Monte Carlo methods on a variety of supercomputers. We present some portable algorithms for generating random numbers on vector and parallel architecture machines. 12 refs., 14 figs

  6. Recent increases in sediment and nutrient accumulation in Bear Lake, Utah/Idaho, USA

    Science.gov (United States)

    Smoak, J.M.; Swarzenski, P.W.

    2004-01-01

    This study examines historical changes in sediment and nutrient accumulation rates in Bear Lake along the northeastern Utah/Idaho border, USA. Two sediment cores were dated by measuring excess 210Pb activities and applying the constant rate of supply (CRS) dating model. Historical rates of bulk sediment accumulation were calculated based on the ages within the sediment cores. Bulk sediment accumulation rates increased throughout the last 100 years. According to the CRS model, bulk sediment accumulation rates were TOC) were calculated by multiplying bulk sediment accumulation rates times the concentrations of these nutrients in the sediment. Accumulation rates of TP, TN, TIC, and TOC increased as a consequence of increased bulk sediment accumulation rates after the re-connection of Bear River with Bear Lake.

  7. Calculated leaching of certain fission products from a cylinder of French glass

    International Nuclear Information System (INIS)

    Blomqvist, G.

    1977-07-01

    The probable total leaching of the most important fission products and actinides have been tabulated for a cylinder of French HLW glass with approximately 9 percent fission products. The calculations cover the period between 30 and 10000 years after removal from the reactor. The cylinder is of the type planned for the introduction of the HLW into Swedish crystalline rocks. All the components are supposed to have the same leach rate. The calculations also include the probable thickness of eroded glass layer/year. (author)

  8. Efigie: a computer program for calculating end-isotope accumulation by neutron irradiation and radioactive decay

    International Nuclear Information System (INIS)

    Ropero, M.

    1978-01-01

    Efigie is a program written in Fortran V which can calculate the concentration of radionuclides produced by neutron irradiation of a target made of either a single isotope or several isotopes. The program includes optimization criteria that can be applied when the goal is the production of a single nuclide. The effect of a cooling time before chemical processing of the target is also accounted for.(author) [es

  9. The influence of body mass index on the accumulation of advanced glycation end products in hemodialysis patients

    NARCIS (Netherlands)

    Arsov, S.; Trajceska, L.; van Oeveren, W.; Smit, A. J.; Dzekova, P.; Stegmayr, B.; Sikole, A.; Rakhorst, G.; Graaff, R.

    BACKGROUND/OBJECTIVES: The level of skin autofluorescence (AF) at a given moment is an independent predictor of mortality in hemodialysis (HD) patients. Skin AF is a measure of the accumulation of advanced glycation end products (AGEs). The aim of the study was to estimate the influence of nutrition

  10. TNG calculations and evaluations of photon production data for some ENDF/B-VI materials

    International Nuclear Information System (INIS)

    Fu, C.Y.

    1994-01-01

    Among the new evaluations in the ENDF/B-VI general purpose files, 25 were based on calculations using TNG, a consistent Hauser-Feshbach pre-equilibrium nuclear model code. The photon production cross sections and spectra were calculated simultaneously with the particle emission cross sections and spectra, assuring energy balance for each reaction. The theories used in TNG for these calculations are summarized. Several examples of photon production data, taken from the ENDF/B-VI files, are compared with the available experimental data

  11. Calculations of long-lived isomer production in neutron reactions

    International Nuclear Information System (INIS)

    Chadwick, M.B.; Young, P.G.

    1992-01-01

    We present theoretical calculations for the production of the long-lived isomers 93m Nb (1/2-, 16 yr), 121m Sn (11/2-, 55 yr), 166m Ho (7-, 1200 yr), 184m Re (8+, 165 d), 186m Re (8+, 2x10 5 yr), 178 Hf (16+, 31 yr), 179m Hf (25/2-, 25 d), and 192m Ir (9+, 241 yr), all of which pose potential radiation activation problems in nuclear fusion reactors if produced in 14-MeV neutron-induced reactions. We consider (n,2n), (n,n'), and (n,γ) production modes and compare our results both with experimental data (where available) and systematics. We also investigate the dependence of the isomeric cross section ratio on incident neutron energy for the isomers under consideration. The statistical Hauser-Feshbach plus preequilibrium code GNASH was used for the calculations. Where discrete state experimental information was lacking, rotational band members above the isomeric state, which can be justified theoretically but have not been experimentally resolved, were reconstructed. (author). 16 refs, 10 figs, 4 tabs

  12. Calculation of radiation production of high specific activity isotopes 192Ir and 60Co

    International Nuclear Information System (INIS)

    Zhou Quan; Zhong Wenfa; Xu Xiaolin

    1997-01-01

    The high specific activity isotopes: 192 Ir and 60 Co in the high neutron flux reactor are calculated with the method of reactor physics. The results of calculation are analyzed in two aspects: the production of isotopes and the influence to parameters of the reactor, and hence a better case is proposed as a reference to the production

  13. Semi-analytic calculations for the impact parameter dependence of electromagnetic multi-lepton pair production

    International Nuclear Information System (INIS)

    Gueclue, M.C.

    2000-01-01

    We provide a new general semi-analytic derivation of the impact parameter dependence of lowest order electromagnetic lepton-pair production in relativistic heavy-ion collisions. By using this result we have also calculated the related analytic multiple-pair production in the two-photon external-field model. We have compared our results with the equivalent-photon approximation and other calculations

  14. Enhanced lipid accumulation and biodiesel production by oleaginous Chlorella protothecoides under a structured heterotrophic-iron (II) induction strategy.

    Science.gov (United States)

    Li, Yuqin; Mu, Jinxiu; Chen, Di; Xu, Hua; Han, Fangxin

    2015-05-01

    A structured heterotrophic-iron (II) induction (HII) strategy was proposed to enhance lipid accumulation in oleaginous Chlorella protothecoides. C. protothecoides subjected to heterotrophic-iron (II) induction achieved a favorable lipid accumulation up to 62 % and a maximum lipid productivity of 820.17 mg/day, representing 2.78-fold and 3.64-fold increase respectively over heterotrophic cultivation alone. HII-induced cells produced significantly elevated levels of 16:0, 18:1(Δ9), and 18:2(Δ9,12) fatty acids (over 90 %). The lipid contents and plant lipid-like fatty acid compositions exhibit the potential of HII-induced C. protothecoides as biodiesel feedstock. Furthermore, 31 altered proteins in HII-induced algal cells were successfully identified. These differentially expressed proteins were assigned into nine molecular function categories, including carbohydrate metabolism, lipid biosynthesis, Calvin cycle, cellular respiration, photosynthesis, energy and transport, protein biosynthesis, regulate and defense, and unclassified. Analysis using the Kyoto encyclopedia of genes and genomes and gene ontology annotation showed that malic enzyme, acyltransferase, and ACP were key metabolic checkpoints found to modulate lipid accumulation in C. protothecoides. The results provided possible applications of HII cultivation strategy in other microalgal species and new possibilities in developing genetic and metabolic engineering microalgae for desirable lipid productivity.

  15. Relativistic total and differential cross section proton--proton electron--positron pair production calculation

    International Nuclear Information System (INIS)

    Rubinstein, J.E.

    1976-01-01

    Circle Feynman diagrams for a specific permutation of variables along with their corresponding algebraic expressions are presented to evaluate [H] 2 for proton-proton electron-positron pair production. A Monte Carlo integration technique is introduced and is used to set up the multiple integral expression for the total pair production cross section. The technique is first applied to the Compton scattering problem and then to an arbitrary multiple integral. The relativistic total cross section for proton-proton electron-positron pair production was calculated for eight different values of incident proton energy. A variety of differential cross sections were calculated for the above energies. Angular differential cross section distributions are presented for the electron, positron, and proton. Invariant mass differential cross section distributions are done both with and without the presence of [H] 2 . Both WGHT and log 10 (TOTAL) distributions were also obtained. The general behavioral trends of the total and differential cross sections for proton-proton electron-positron pair production are presented. The range of validity for this calculation is from 0 to about 200 MeV

  16. Calculation of isotopic mass and energy production by a matrix operator method

    International Nuclear Information System (INIS)

    Lee, C.E.

    1976-08-01

    The Volterra method of the multiplicative integral is used to determine the isotopic density, mass, and energy production in linear systems. The solution method, assumptions, and limitations are discussed. The method allows a rapid accurate calculation of the change in isotopic density, mass, and energy production independent of the magnitude of the time steps, production or decay rates, or flux levels

  17. Accumulation of Advanced Glycation End Products as a Molecular Mechanism for Aging as a Risk Factor in Osteoarthritis

    NARCIS (Netherlands)

    Groot, J. de; Verzijl, N.; Wenting-Wijk, M.J.G. van; Jacobs, K.M.G.; El, B. van; Roermund, P.M. van; Bank, R.A.; Bijlsma, J.W.J.; TeKoppele, J.M.; Lafeber, F.P.J.G.

    2004-01-01

    Objective. Osteoarthritis (OA) is one of the most prevalent and disabling chronic conditions affecting the elderly. Its etiology is largely unknown, but age is the most prominent risk factor. The current study was designed to test whether accumulation of advanced glycation end products (AGEs), which

  18. The association between various smoking behaviors, cotinine biomarkers and skin autofluorescence, a marker for advanced glycation end product accumulation

    NARCIS (Netherlands)

    van Waateringe, Robert P.; Mook-Kanamori, Marjonneke J.; Slagter, Sandra N.; van der Klauw, Melanie M.; van Vliet-Ostaptchouk, Jana V.; Graaff, Reindert; Lutgers, Helen L.; Suhre, Karsten; Selim, Mohammed M. El-Din; Mook-Kanamori, Dennis O.; Wolffenbuttel, Bruce H. R.

    2017-01-01

    BACKGROUND: Skin autofluorescence, a biomarker for advanced glycation end products (AGEs) accumulation, has been shown to predict diabetes-related cardiovascular complications and is associated with several environmental and lifestyle factors. In the present study, we examined the association

  19. Correlation of different spectral lights with biomass accumulation and production of antioxidant secondary metabolites in callus cultures of medicinally important Prunella vulgaris L.

    Science.gov (United States)

    Fazal, Hina; Abbasi, Bilal Haider; Ahmad, Nisar; Ali, Syed Shujait; Akbar, Fazal; Kanwal, Farina

    2016-06-01

    Light is one of the key elicitors that directly fluctuates plant developmental processes and biosynthesis of secondary metabolites. In this study, the effects of various spectral lights on biomass accumulation and production of antioxidant secondary metabolites in callus cultures of Prunella vulgaris were investigated. Among different spectral lights, green light induced the maximum callogenic response (95%). Enhanced fresh biomass accumulation was observed in log phases on day-35, when callus cultures were exposed to yellow and violet lights. Yellow light induced maximum biomass accumulation (3.67g/100ml) from leaf explants as compared to control (1.27g/100ml). In contrast, violet lights enhanced biomass accumulation (3.49g/100ml) from petiole explant. Maximum total phenolics content (TPC; 23.9mg/g-DW) and total flavonoids content (TFC; 1.65mg/g-DW) were observed when cultures were grown under blue lights. In contrast, green and yellow lights enhanced total phenolics production (TPP; 112.52g/100ml) and total flavonoids production (TFP; 9.64g/100ml) as compared to control. The calli grown under green, red and blue lights enhanced DPPH-free radical scavenging activity (DFRSA; 91.3%, 93.1% and 93%) than control (56.44%) respectively. The DFRSA was correlated either with TPC and TFC or TPP and TFP. Furthermore, yellow lights enhanced superoxide dismutase (SOD), peroxidase (POD) and protease activities, however, the content of total protein (CTP) was higher in control cultures (186μg BSAE/mg FW) as compared to spectral lights. These results suggest that the exposure of callus cultures to various spectral lights have shown a key role in biomass accumulation and production of antioxidant secondary metabolites. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Spectral lights trigger biomass accumulation and production of antioxidant secondary metabolites in adventitious root cultures of Stevia rebaudiana (Bert.).

    Science.gov (United States)

    Idrees, Muhammad; Sania, Bibi; Hafsa, Bibi; Kumari, Sana; Khan, Haji; Fazal, Hina; Ahmad, Ishfaq; Akbar, Fazal; Ahmad, Naveed; Ali, Sadeeq; Ahmad, Nisar

    2018-05-30

    Stevia rebaudiana (S. rebaudiana) is the most important therapeutic plant species and has been accepted as such worldwide. It has a tendency to accumulate steviol glycosides, which are 300 times sweeter than marketable sugar. Recently, diabetic patients commonly use this plant as a sugar substitute for sweet taste. In the present study, the effects of different spectral lights were investigated on biomass accumulation and production of secondary metabolites in adventitious root cultures of S. rebaudiana. For callus development, leaf explants were excised from seed-derived plantlets and inoculated on a Murashige and Skoog (MS) medium containing the combination of 2,4-dichlorophenoxy acetic acid (2, 4-D, 2.0mg/l) and 6-benzyladenine (BA, 2.0mg/l), while 0.5mg/l naphthalene acetic acid (NAA) was used for adventitious root culture. Adventitious root cultures were exposed to different spectral lights (blue, green, violet, red and yellow) for a 30-day period. White light was used as control. The growth kinetics was studied for 30days with 3-day intervals. In this study, the violet light showed the maximum accumulation of fresh biomass (2.495g/flask) as compared to control (1.63g/flask), while red light showed growth inhibition (1.025g/flask) as compared to control. The blue light enhanced the highest accumulation of phenolic content (TPC; 6.56mg GAE/g DW), total phenolic production (TPP; 101mg/flask) as compared to control (5.44mg GAE/g DW; 82.2mg GAE/g DW), and exhibited a strong correlation with dry biomass. Blue light also improved the accumulation of total flavonoid content (TFC; 4.33mg RE/g DW) and total flavonoid production (TFP; 65mg/flask) as compared to control. The violet light showed the highest DPPH inhibition (79.72%), while the lowest antioxidant activity was observed for control roots (73.81%). Hence, we concluded that the application of spectral lights is an auspicious strategy for the enhancement of the required antioxidant secondary metabolites in

  1. Age-related accumulation of advanced glycation end-products-albumin, S100β, and the expressions of advanced glycation end product receptor differ in visceral and subcutaneous fat

    Energy Technology Data Exchange (ETDEWEB)

    Son, Kuk Hui [Department of Thoracic and Cardiovascular Surgery, Gachon University Gil Medical Center, Gachon University, Incheon (Korea, Republic of); Son, Myeongjoo [Department of Anatomy and Cell Biology, Gachon University Graduate School of Medicine, Incheon (Korea, Republic of); Functional Cellular Networks Laboratory, Lee Gil Ya Cancer and Diabetes Institute, Gachon University, Incheon (Korea, Republic of); Ahn, Hyosang; Oh, Seyeon; Yum, Yoonji [Functional Cellular Networks Laboratory, Lee Gil Ya Cancer and Diabetes Institute, Gachon University, Incheon (Korea, Republic of); Choi, Chang Hu [Department of Thoracic and Cardiovascular Surgery, Gachon University Gil Medical Center, Gachon University, Incheon (Korea, Republic of); Park, Kook Yang, E-mail: kkyypark@ghil.com [Department of Thoracic and Cardiovascular Surgery, Gachon University Gil Medical Center, Gachon University, Incheon (Korea, Republic of); Byun, Kyunghee, E-mail: khbyun1@gachon.ac.kr [Department of Anatomy and Cell Biology, Gachon University Graduate School of Medicine, Incheon (Korea, Republic of); Functional Cellular Networks Laboratory, Lee Gil Ya Cancer and Diabetes Institute, Gachon University, Incheon (Korea, Republic of)

    2016-08-19

    Visceral fat induces more inflammation by activating macrophages than subcutaneous fat, and inflammation is an underlying feature of the pathogeneses of various diseases, including cardiovascular disease and diabetes. Advanced glycation end products (AGEs), S100β, and their receptors, the receptor for advanced glycation end products (RAGE), lead to macrophage activation. However, little information is available regarding the differential accumulations of AGE-albumin (serum albumin modified by AGEs), S100β, or expressions of RAGE in different adipocyte types in fat tissues. In this study, the authors investigated whether age-related AGE-albumin accumulations S100β level, and RAGE expressions differ in subcutaneous and visceral fat tissues. Subcutaneous and visceral fat were harvested from 3- and 28-week-old rats. Macrophage activation was confirmed by Iba1 staining, and AGE-albumin accumulations and RAGE expressions were assessed by confocal microscopy. S100β were analyzed by immunoblotting. It was found that activated macrophage infiltration, AGE-albumin accumulation, and S100β in visceral fat was significantly greater in 28-week-old rats than in 3-week-old rats, but similar in subcutaneous fat. The expression of RAGE in visceral fat was much greater in 28-week-old rats, but its expression in subcutaneous fat was similar in 3- and 28-week-old rats. Furthermore, inflammatory signal pathways (NFκB, TNF-α) and proliferation pathways (FAK) in visceral fat were more activated in 28-week-old rats. These results imply that age-related AGE-albumin accumulation, S100β, and RAGE expression are more prominent in visceral than in subcutaneous fat, suggesting that visceral fat is involved in the pathogenesis of inflammation-induced diseases in the elderly. - Highlights: • The age-related AGE-albumin accumulation and S100β were more prominent in visceral than subcutaneous fat. • The age-related RAGE expression were more prominent in visceral than subcutaneous fat.

  2. Age-related accumulation of advanced glycation end-products-albumin, S100β, and the expressions of advanced glycation end product receptor differ in visceral and subcutaneous fat

    International Nuclear Information System (INIS)

    Son, Kuk Hui; Son, Myeongjoo; Ahn, Hyosang; Oh, Seyeon; Yum, Yoonji; Choi, Chang Hu; Park, Kook Yang; Byun, Kyunghee

    2016-01-01

    Visceral fat induces more inflammation by activating macrophages than subcutaneous fat, and inflammation is an underlying feature of the pathogeneses of various diseases, including cardiovascular disease and diabetes. Advanced glycation end products (AGEs), S100β, and their receptors, the receptor for advanced glycation end products (RAGE), lead to macrophage activation. However, little information is available regarding the differential accumulations of AGE-albumin (serum albumin modified by AGEs), S100β, or expressions of RAGE in different adipocyte types in fat tissues. In this study, the authors investigated whether age-related AGE-albumin accumulations S100β level, and RAGE expressions differ in subcutaneous and visceral fat tissues. Subcutaneous and visceral fat were harvested from 3- and 28-week-old rats. Macrophage activation was confirmed by Iba1 staining, and AGE-albumin accumulations and RAGE expressions were assessed by confocal microscopy. S100β were analyzed by immunoblotting. It was found that activated macrophage infiltration, AGE-albumin accumulation, and S100β in visceral fat was significantly greater in 28-week-old rats than in 3-week-old rats, but similar in subcutaneous fat. The expression of RAGE in visceral fat was much greater in 28-week-old rats, but its expression in subcutaneous fat was similar in 3- and 28-week-old rats. Furthermore, inflammatory signal pathways (NFκB, TNF-α) and proliferation pathways (FAK) in visceral fat were more activated in 28-week-old rats. These results imply that age-related AGE-albumin accumulation, S100β, and RAGE expression are more prominent in visceral than in subcutaneous fat, suggesting that visceral fat is involved in the pathogenesis of inflammation-induced diseases in the elderly. - Highlights: • The age-related AGE-albumin accumulation and S100β were more prominent in visceral than subcutaneous fat. • The age-related RAGE expression were more prominent in visceral than subcutaneous fat.

  3. Carbon Accumulation during Photosynthesis in Leaves of Nitrogen- and Phosphorus-Stressed Cotton.

    Science.gov (United States)

    Radin, J W; Eidenbock, M P

    1986-11-01

    Leaves of cotton (Gossypium hirsutum L.) accumulate considerable dry mass per unit area during photosynthesis. The percentage of C in that accumulated dry mass was estimated as the regression coefficient (slope) of a linear regression relating C per unit area to total dry mass per unit area. Plants were grown on full nutrients or on N- or P-deficient nutrient solutions. In the fully nourished controls, the mass that accumulated over a 9-hour interval beginning at dawn contained 38.6% C. N and P stress increased the C concentration of accumulated mass to 49.7% and 45.1%, respectively. Nutrient stress also increased the starch concentration of accumulated mass, but starch alone could not account for the differences in C concentration. P stress decreased the estimated rate of C export from source leaves, calculated as the difference between C assimilation and C accumulation. The effect of P stress on apparent export was very sensitive to the C concentration used in the calculation, and would not have been revealed with an assumption of unchanged C concentration in the accumulated mass.

  4. Factors influencing the cardiac MIBG accumulation

    International Nuclear Information System (INIS)

    Takatsu, Hisato; Fujiwara, Hisayoshi

    1997-01-01

    Following factors possibly influencing the cardiac MIBG accumulation were examined mainly in mice. 1. The specific activity of the MIBG (meta-iodo-benzyl guanidine) on the neuronal and non-neuronal fractions. 2. Motor restriction stress on MIBG accumulation and washout. 3. Loading and restriction of sodium chloride on the accumulation and effect of suppression of renin-angiotensin system. 4. Examinations in Dahl rats. 125I- or 131I-MIBG was intravenously administered to mice at 74 kBq. At 30 min or 4 hr after administration, mice were sacrificed and their left ventricles were dissected out for measurement of radioactivity in a liquid scintillation counter. Salt-sensitive and -resistant Dahl rats were given with 37 MBq of 123I-MIBG and cardiac radioactivity was measured externally for calculation of washout. Factors examined were found highly correlated with the accumulation of MIBG and measurement of its washout was considered useful for evaluating sympathetic activity. (K.H.)

  5. Measurement, calculation and evaluation of photon production cross-sections

    International Nuclear Information System (INIS)

    Kocherov, N.P.

    1990-03-01

    The IAEA Specialists' Meeting on Measurement, Calculation and Evaluation of Photon Production Cross-Sections was held in Smolenice, Czechoslovakia, 5-7 February 1990. The meeting was hosted by the Institute of Physics of the Electro-Physical Research Centre, Slovak Academy of Sciences, Bratislava. This report contains the conclusions and recommendations of this meeting. The papers which the participants have presented at the meeting will be published as an INDC Report. (author)

  6. Carbon black nanoparticles promote endothelial activation and lipid accumulation in macrophages independently of intracellular ROS production

    DEFF Research Database (Denmark)

    Cao, Yi; Roursgaard, Martin; Danielsen, Pernille Høgh

    2014-01-01

    , the concentrations of CB to induce lipid accumulation were lower than the concentrations to promote intracellular ROS production in THP-1a cells. In conclusion, exposure to nano-sized CB induced endothelial dysfunction and foam cell formation, which was not dependent on intracellular ROS production....... and WST-1 assays, especially in THP-1 and THP-1a cells. The CB exposure decreased the glutathione (GSH) content in THP-1 and THP-1a cells, whereas GSH was increased in HUVECs. The reactive oxygen species (ROS) production was increased in all cell types after CB exposure. A reduction of the intracellular...... GSH concentration by buthionine sulfoximine (BSO) pre-treatment further increased the CB-induced ROS production in THP-1 cells and HUVECs. The expression of adhesion molecules ICAM-1 and VCAM-1, but not adhesion of THP-1 to HUVECs or culture dishes, was elevated by CB exposure, whereas these effects...

  7. Automated calculations for massive fermion production with ai-bar Talc

    International Nuclear Information System (INIS)

    Lorca, A.; Riemann, T.

    2004-01-01

    The package ai-bar Talc has been developed for the automated calculation of radiative corrections to two-fermion production at e + e - colliders. The package uses Diana, Qgraf, Form, Fortran, FF, LoopTools, and further unix/linux tools. Numerical results are presented for e + e - -> e + e - , μ + μ - , bs-bar , tc-bar

  8. Stontium-90 contamination in vegetation from radioactive waste seepage areas at ORNL, and theoretical calculations of /sup 90/Sr accumulation by deer

    Energy Technology Data Exchange (ETDEWEB)

    Garten, C.T. Jr.; Lomax, R.D.

    1987-06-01

    This report describes data obtained during a preliminary characterization of /sup 90/Sr levels in browse vegetation from the vicinity of seeps adjacent to ORNL solid waste storage areas (SWSA) where deer (Odocoileus virginianus) were suspected to accumulate /sup 90/Sr through the food chain. The highest strontium concentrations in plant samples were found at seeps associated with SWSA-5. Strontium-90 concentrations in honeysuckle and/or blackberry shoots from two seeps in SWSA-5 averaged 39 and 19 nCi/g dry weight (DW), respectively. The maximum concentration observed was 90 nCi/g DW. Strontium-90 concentrations in honeysuckle and blackberry shoots averaged 7.4 nCi/g DW in a study area south of SWSA-4, and averaged 1.0 nCi/g DW in fescue grass from a seepage area located on SWSA-4. A simple model (based on metabolic data for mule deer) has been used to describe the theoretical accumulation of /sup 90/Sr in bone of whitetail deer following ingestion of contaminated vegetation. These model calculations suggest that if 30 pCi /sup 90/Sr/g deer bone is to be the accepted screening level for retaining deer killed on the reservation, then 5-pCi /sup 90/Sr/g DW vegetation should be considered as a possible action level in making decisions about the need for remedial measures, because unrestricted access and full utilization of vegetation contaminated with <5 pCi/g DW results in calculated steady-state (maximum) /sup 90/Sr bone concentrations of <30 pCi/g in a 45-kg buck.

  9. Simulation of peat accumulation: an aid in carbon cycling research

    International Nuclear Information System (INIS)

    Dierendonck, M.C. van

    1992-01-01

    Some preliminary results of a technique used to compare primary production and peat accumulation data mainly from published sources and the results of a peat accumulation simulation model are presented. Emphasis is on differences among micro-sites (hummock, lawn, hollow and pool) and among various Sphagnum species (S. fuscum, S. magellanicum, S. cuspidatum and S. balticum) associated with raised bogs. The primary production of lawns and pools were significantly greater than those of hummocks and hollows. Sphagnum balticum had the highest primary production (mean=339 g/m - 2a -1 ) Over 90 % of the primary production of Sphagnum fuscum is accumulated while for the other Sphagnum species, the value is <50 %. The data are used in a simulation model to show the influence of doubling of rainfall on primary production over a 50 year period

  10. Calculation of the spallation product distribution in the evaporation process

    International Nuclear Information System (INIS)

    Nishida, T.; Kanno, I.; Nakahara, Y.; Takada, H.

    1989-01-01

    Some investigations are performed for the calculational model of nuclear spallation reaction in the evaporation process. A new version of a spallation reaction simulation code NUCLEUS has been developed by incorporating the newly revised Uno ampersand Yamada's mass formula and extending the counting region of produced nuclei. The differences between the new and original mass formulas are shown in the comparisons of mass excess values. The distributions of spallation products of a uranium target nucleus bombarded by energy (0.38 - 2.9 GeV) protons have been calculated with the new and original versions of NUCLEUS. In the fission component Uno ampersand Yamada's mass formula reproduces the measured data obtained from thin foil experiments significantly better, especially in the neutron excess side, than the combination of the Cameron's mass formula and the mass table compiled by Wapstra, et al., in the original version of NUCLEUS. Discussions are also made on how the mass-yield distribution of products varies dependent on the level density parameter a characterizing the particle evaporation. 16 refs., 7 figs., 1 tab

  11. Calculation of the spallation product distribution in the evaporation process

    International Nuclear Information System (INIS)

    Nishida, T.; Kanno, I.; Nakahara, Y.; Takada, H.

    1989-01-01

    Some investigations are performed for the calculational model of nuclear spallation reaction in the evaporation process. A new version of a spallation reaction simulation code NUCLEUS has been developed by incorporating the newly revised Uno and Yamada's mass formula and extending the counting region of produced nuclei. The differences between the new and original mass formulas are shown in the comparisons of mass excess values. The distributions of spallation products of a uranium target nucleus bombarded by energy (0.38 - 2.9 GeV) protons have been calculated with the new and original versions of NUCLEUS. In the fission component Uno and Yamada's mass formula reproduces the measured data obtained from thin foil experiments significantly better, especially in the neutron excess side, than the combination of the Cameron's mass formula and the mass table compiled by Wapstra, et al., in the original version of NUCLEUS. Discussions are also made on how the mass-yield distribution of products varies dependent on the level density parameter α characterizing the particle evaporation. (author)

  12. Calculated inclusive neutron production from 400 GeV proton-nucleus collisions

    International Nuclear Information System (INIS)

    Alsmiller, R.G. Jr.; Alsmiller, F.S.; Hermann, O.W.

    1989-08-01

    Calculated inclusive neutron production from 400 GeV proton-nucleus collisions is presented and compared with experimental data. Target nuclei H, Be, Cu, and Pb are considered and the comparisons cover the laboratory energy range of 20 to 400 GeV, and angular range 0.7 to 10 mr. Moderately good agreement between the calculated and experimental data is found, but the agreement in the case of Be, Cu and Pb is significantly better than in the case of H. 8 refs., 4 figs

  13. Endophyte Chaetomium globosum D38 Promotes Bioactive Constituents Accumulation and Root Production in Salvia miltiorrhiza

    Directory of Open Access Journals (Sweden)

    Xin Zhai

    2018-01-01

    Full Text Available Salvia miltiorrhiza is known for tanshinones and salvianolic acids, which have been shown to have a protective effect against ROS, especially for cardiovascular diseases and other various ailments of human organs. Due to the low yield of tanshinones and their analogs in S. miltiorrhiza, multiple stimulation strategies have been developed to improve tanshinones production in plant tissue cultures. Endophytic fungi have been reported to form different relationships with their host plants, including symbiotic, mutualistic, commensalistic, and parasitic interactions. Thus we take the assumption that endophytic fungi may be a potential microbial tool for secondary metabolism promotion in medicinal plants. We recently isolated Chaetomium globosum D38 from the roots of S. miltiorrhiza and our study aimed to examine the effects of this live endophytic fungus D38 and its elicitor on the accumulation of tanshinones in the hairy root cultures of S. miltiorrhiza. Our results revealed that C. globosum D38 mainly colonized in the intercellular gap of xylem parenchyma cells of S. miltiorrhiza hairy roots during the long term co-existence without any toxicity. Moreover, both of the live fungus and its mycelia extract could increase the production of tanshinones, especially for dihydrotanshinone I and cryptotanshinone. The effect of the mycelia extract was much stronger than that of the live fungus on tanshinones synthesis, which significantly increased the transcriptional activity of those key genes in tanshinone biosynthetic pathway. Furthermore, the live C. globosum D38 could also be made into biotic fertilizer used for S. miltiorrhiza seedlings culture, which not only significantly promoted the growth of the host plant, but also notably enhanced the accumulation of tanshinones and salvianolic acids. We thus speculated that, in the soil environment D38 could form bitrophic and mutual beneficial interactions with the host and enhance the plant growth and its

  14. Accumulative charge separation for solar fuels production: coupling light-induced single electron transfer to multielectron catalysis.

    Science.gov (United States)

    Hammarström, Leif

    2015-03-17

    The conversion and storage of solar energy into a fuel holds promise to provide a significant part of the future renewable energy demand of our societies. Solar energy technologies today generate heat or electricity, while the large majority of our energy is used in the form of fuels. Direct conversion of solar energy to a fuel would satisfy our needs for storable energy on a large scale. Solar fuels can be generated by absorbing light and converting its energy to chemical energy by electron transfer leading to separation of electrons and holes. The electrons are used in the catalytic reduction of a cheap substrate with low energy content into a high-energy fuel. The holes are filled by oxidation of water, which is the only electron source available for large scale solar fuel production. Absorption of a single photon typically leads to separation of a single electron-hole pair. In contrast, fuel production and water oxidation are multielectron, multiproton reactions. Therefore, a system for direct solar fuel production must be able to accumulate the electrons and holes provided by the sequential absorption of several photons in order to complete the catalytic reactions. In this Account, the process is termed accumulative charge separation. This is considerably more complicated than charge separation on a single electron level and needs particular attention. Semiconductor materials and molecular dyes have for a long time been optimized for use in photovoltaic devices. Efforts are made to develop new systems for light harvesting and charge separation that are better optimized for solar fuel production than those used in the early devices presented so far. Significant progress has recently been made in the discovery and design of better homogeneous and heterogeneous catalysts for solar fuels and water oxidation. While the heterogeneous ones perform better today, molecular catalysts based on transition metal complexes offer much greater tunability of electronic and

  15. Fission product inventory calculation by a CASMO/ORIGEN coupling program

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Do Heon; Kim, Jong Kyung [Hanyang University, Seoul (Korea, Republic of); Choi, Hang Bok; Roh, Gyu Hong; Jung, In Ha [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1998-12-31

    A CASMO/ORIGEN coupling utility program was developed to predict the composition of all the fission products in spent PWR fuels. The coupling program reads the CASMO output file, modifies the ORIGEN cross section library and reconstructs the ORIGEN input file at each depletion step. In ORIGEN, the burnup equation is solved for actinides and fission products based on the fission reaction rates and depletion flux of CASMO. A sample calculation has been performed using a 14 x 14 PWR fuel assembly and the results are given in this paper. 3 refs., 1 fig., 1 tab. (Author)

  16. Fission product inventory calculation by a CASMO/ORIGEN coupling program

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Do Heon; Kim, Jong Kyung [Hanyang University, Seoul (Korea, Republic of); Choi, Hang Bok; Roh, Gyu Hong; Jung, In Ha [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1997-12-31

    A CASMO/ORIGEN coupling utility program was developed to predict the composition of all the fission products in spent PWR fuels. The coupling program reads the CASMO output file, modifies the ORIGEN cross section library and reconstructs the ORIGEN input file at each depletion step. In ORIGEN, the burnup equation is solved for actinides and fission products based on the fission reaction rates and depletion flux of CASMO. A sample calculation has been performed using a 14 x 14 PWR fuel assembly and the results are given in this paper. 3 refs., 1 fig., 1 tab. (Author)

  17. Benchmark calculations on residue production within the EURISOL DS project; Part II: thick targets

    CERN Document Server

    David, J.-C; Boudard, A; Doré, D; Leray, S; Rapp, B; Ridikas, D; Thiollière, N

    Benchmark calculations on residue production using MCNPX 2.5.0. Calculations were compared to mass-distribution data for 5 different elements measured at ISOLDE, and to specific activities of 28 radionuclides in different places along the thick target measured in Dubna.

  18. Carbon Calculator for Land Use Change from Biofuels Production (CCLUB) Users’ Manual and Technical Documentation

    Energy Technology Data Exchange (ETDEWEB)

    Dunn, Jennifer B. [Argonne National Lab. (ANL), Argonne, IL (United States); Qin, Zhangcai [Argonne National Lab. (ANL), Argonne, IL (United States); Mueller, Steffen [Univ. of Illinois, Chicago, IL (United States); Kwon, Ho-young [International Food Policy Research Inst., Washington, DC (United States); Wander, Michelle M. [Univ. of Illinois, Urbana-Champaign, IL (United States); Wang, Michael [Argonne National Lab. (ANL), Argonne, IL (United States)

    2017-12-01

    The Carbon Calculator for Land Use Change from Biofuels Production (CCLUB) calculates carbon emissions from land use change (LUC) for four different ethanol production pathways including corn grain ethanol and cellulosic ethanol from corn stover, Miscanthus, and switchgrass, and a soy biodiesel pathway. This document discusses the version of CCLUB released September 30, 2017 which includes five ethanol LUC scenarios and four soy biodiesel LUC scenarios.

  19. Simulation of peat accumulation: an aid in carbon cycling research

    Energy Technology Data Exchange (ETDEWEB)

    Dierendonck, M.C. van (Amsterdam Univ. (Netherlands). Hugo de Vries Laboratory)

    1992-01-01

    Some preliminary results of a technique used to compare primary production and peat accumulation data mainly from published sources and the results of a peat accumulation simulation model are presented. Emphasis is on differences among micro-sites (hummock, lawn, hollow and pool) and among various Sphagnum species (S. fuscum, S. magellanicum, S. cuspidatum and S. balticum) associated with raised bogs. The primary production of lawns and pools were significantly greater than those of hummocks and hollows. Sphagnum balticum had the highest primary production (mean=339 g/m[sup -]2a[sup -1]) Over 90 % of the primary production of Sphagnum fuscum is accumulated while for the other Sphagnum species, the value is <50 %. The data are used in a simulation model to show the influence of doubling of rainfall on primary production over a 50 year period

  20. Map of calculated radioactivity of fission product, 3

    International Nuclear Information System (INIS)

    Takeda, Tsuneo

    1977-02-01

    In this work, the radioactivities of fission products were calculated and summarized in contour maps and tables depending on irradiation and cooling times. The irradiation condition and other parameters used for the present calculation are shown in the followings. Neutron flux (N sub(th)): 3x10 13 n/sec/cm 2 Atom number of uranium: 1 mole (6x10 23 , ca. 271 gUO 2 ) Enrichment of U-235: 2.7% Range of irradiation time: 60-6x10 7 sec (ca. 1.9 y) Range of cooling time: 60-6x10 7 sec (ca. 1.9 y). Values of the neutron flux and the enrichment treated here are representative for common LWRs. The maps and tables of 560 nuclides are divided and compiled into the following three volumes. Vol. I: Maps of radioactivity of overall total, element total and each nuclide (Ni - Zr), Vol. II: Maps of radioactivity of each nuclide (Nb - Sb), Vol. III: Maps of radioactivity of each nuclide (Te - Tm). (auth.)

  1. Map of calculated radioactivity of fission product, (1)

    International Nuclear Information System (INIS)

    Takeda, Tsuneo

    1977-02-01

    In this work, the radioactivities of fission products were calculated and summarized in contour maps and tables depending on irradiation and cooling times. The irradiation condition and other parameters used for the present calculation are shown in the followings. Neutron flux (N sub(th)): 3x10 13 n/sec/cm 2 Atom number of uranium: 1 mole (6x10 23 , ca. 271 gUO 2 ) Enrichment of U-235: 2.7% Range of irradiation time: 60-6x10 7 sec (ca. 1.9 y) Range of cooling time: 60-6x10 7 sec (ca. 1.9 y). Values of the neutron flux and the enrichment treated here are representative for common LWRs. The maps and tables of 560 nuclides are divided and compiled into the following three volumes. Vol. I Maps of radioactivity of overall total, element total and each nuclide (Ni - Zr) Vol. II Maps of radioactivity of each nuclide (Nb - Sb) Vol. III Maps of radioactivity of each nuclide (Te - Tm) (auth.)

  2. Map of calculated radioactivity of fission product, 2

    International Nuclear Information System (INIS)

    Takeda, Tsuneo

    1977-02-01

    In this work, the radioactivities of fission products were calculated and summarized in contour maps and tables depending on irradiation and cooling times. The irradiation condition and other parameters used for the present calculation are shown in the followings. Neutron flux (N sub(th)): 3x10 13 n/sec/cm 2 Atom number of uranium: 1 mole (6x10 23 , ca. 271 gUO 2 ) Enrichment of U-235: 2.7% Range of irradiation time: 60-6x10 7 sec (ca. 1.9 y) Range of cooling time: 60-6x10 7 sec (ca. 1.9 y). Values of the neutron flux and the enrichment treated here are representative for common LWRs. The maps and tables of 560 nuclides are divided and compiled into the following three volumes. Vol. I: Maps of radioactivity of overall total, element total and each nuclide (Ni - Zr), Vol. II: Maps of radioactivity of each nuclide (Nb - Sb), Vol. III: Maps of radioactivity of each nuclide (Te - Tm). (auth.)

  3. LCA calculations on Swedish wood pellet production chains - according to the Renewable Energy Directive

    Energy Technology Data Exchange (ETDEWEB)

    Hagberg, Linus; Saernholm, Erik; Gode, Jenny; Ekvall, Tomas; Rydberg, Tomas

    2009-09-15

    The study includes calculations of typical life cycle emissions of greenhouse gases for representative Swedish pellet production chains in accordance with the calculation rules in RED (Directive 2009/28/EC). The study also intends to analyse how the directive is applicable on solid biofuels in general and on wood pellet production in particular, and to identify such aspects of the methodology in RED that are associated with obscurities, problems or lead to misleading results compared to other life cycle analysis principles. The report includes a large number of alternative calculations to show how different facts, assumptions and methodological choices affect the results. This includes the effect of what fuels are used for drying, different transport distances, assumed fuel mix for purchased electricity, the variance in efficiency between the investigated plants as well as the effect of different interpretations of the RED methodology for greenhouse gas calculations

  4. Nature, origin, and production characteristics of the Lower Silurian regional oil and gas accumulation, central Appalachian basin, United States

    Science.gov (United States)

    Ryder, R.; Zagorski, W.A.

    2003-01-01

    uplift and erosion, causing gas leakage and a marked reduction in fluid pressure. Most future natural-gas production in the Clinton/Medina sandstones is anticipated to come from the basin-center accumulation. The Tuscarora Sandstone has additional gas resources but typically low reservoir porosity and permeability, and the likelihood of low-energy (in British thermal units) gas reduce the incentive to explore for it.

  5. Betel-quid and alcohol use were associated with lipid accumulation product among male factory workers in Taiwan.

    Science.gov (United States)

    Huang, Chih-Fang; Chen, Chao-Tung; Wang, Pei-Ming; Koo, Malcolm

    2015-05-01

    In this study, cardiometabolic risk associated with betel-quid, alcohol and cigarette use, based on a simple index-lipid accumulation product (LAP), was investigated in Taiwanese male factory workers. Male factory workers were recruited during their annual routine health examination at a hospital in south Taiwan. The risk of cardiometabolic disorders was estimated by the use of LAP, calculated as (waist circumference [cm]-65)×(triglyceride concentration [mmol/l]). Multiple linear regression analyses were conducted to assess the risk factors of natural logarithm-transformed LAP. Of the 815 participants, 40% (325/815) were current alcohol users, 30% (248/815) were current smokers and 7% (53/815) were current betel-quid users. Current betel-quid use, alcohol use, older age, lack of exercise and higher body mass index were found to be significant and independent factors associated with natural logarithm-transformed LAP. Betel-quid and alcohol, but not cigarette use, were independent risk factors of logarithm-transformed LAP, adjusting for age, exercise and body mass index in male Taiwanese factory workers. LAP can be considered as a simple and useful method for screening of cardiometabolic risk. © The Author 2014. Published by Oxford University Press on behalf of Royal Society of Tropical Medicine and Hygiene. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  6. Influence of irradiation parameters on damage accumulation in metals and alloys

    DEFF Research Database (Denmark)

    Singh, B.N.; Zinkle, S.J.

    1994-01-01

    , helium production rate and the production rate of transmutant impurities may affect the rate and the magnitude of the damage accumulation. Possible mechanisms by which these parameters may affect the damage accumulation are described. Specific examples are given to illustrate the fact that the recoil...

  7. Heat and cold accumulators in vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Kauranen, P.; Wikstroem, L. (VTT Technical Research Centre of Finland, Advanced Materials, Tampere (Finland)); Heikkinen, J. (VTT Technical Research Centre of Finland, Building Services and Indoor Environment, Espoo (Finland)); Laurikko, J.; Elonen, T. (VTT Technical Research Centre of Finland, Emission Control, Espoo (Finland)); Seppaelae, A. (Helsinki Univ. of Technology, Applied Thermodynamics, Espoo (Finland)). Email: ari.seppala@tkk.fi

    2009-07-01

    Phase Change Material (PCM) based heat and cold accumulators have been tailored for transport applications including a mail delivery van as well as the cold chains of foodstuff and blood products. The PCMs can store relative large amount of thermal energy in a narrow temperature interval as latent heat of fusion of their melting and crystallization processes. Compact heat and cold accumulators can be designed using PCMs. The aim of the project has been to reduce the exhaust gas and noise emissions and improve the fuel economy of the transport systems and to improve the reliability of the cold chains studied by storing thermal energy in PCM accumulators. (orig.)

  8. Calculation of vapor pressure of fission product fluorides and oxyfluorides

    International Nuclear Information System (INIS)

    Roux, J.P.

    1976-03-01

    The equilibrium diagrams of the condensed phases - solid and liquid - and vapor phase are collected for the principal fluorides and oxyfluorides of fission product elements (atomic number from 30 to 66). These diagrams are used more particularly in fuel reprocessing by fluoride volatility process. Calculations and curves (vapor pressure in function of temperature) are processed using a computer program given in this report [fr

  9. Classification and calculation of primary failure modes in bread production line

    International Nuclear Information System (INIS)

    Tsarouhas, Panagiotis H.

    2009-01-01

    In this study, we describe the classification methodology over a 2-year period of the primary failure modes in categories based on failure data of bread production line. We estimate the probabilities of these categories applying the chi-square goodness of fit test, and we calculate their joint probabilities of mass function at workstation and line level. Then, we present numerical examples in order to predict the causes and frequencies of breakdowns for workstations and for the entire bread production line that will occur in the future. The methodology is meant to guide bread and bakery product manufacturers, improving the operation of the production lines. It can also be a useful tool to maintenance engineers, who wish to analyze and improve the reliability and efficiency of the manufacturing systems

  10. Flavonoid accumulation patterns of transparent testa mutants of arabidopsis

    Science.gov (United States)

    Peer, W. A.; Brown, D. E.; Tague, B. W.; Muday, G. K.; Taiz, L.; Murphy, A. S.

    2001-01-01

    Flavonoids have been implicated in the regulation of auxin movements in Arabidopsis. To understand when and where flavonoids may be acting to control auxin movement, the flavonoid accumulation pattern was examined in young seedlings and mature tissues of wild-type Arabidopsis. Using a variety of biochemical and visualization techniques, flavonoid accumulation in mature plants was localized in cauline leaves, pollen, stigmata, and floral primordia, and in the stems of young, actively growing inflorescences. In young Landsberg erecta seedlings, aglycone flavonols accumulated developmentally in three regions, the cotyledonary node, the hypocotyl-root transition zone, and the root tip. Aglycone flavonols accumulated at the hypocotyl-root transition zone in a developmental and tissue-specific manner with kaempferol in the epidermis and quercetin in the cortex. Quercetin localized subcellularly in the nuclear region, plasma membrane, and endomembrane system, whereas kaempferol localized in the nuclear region and plasma membrane. The flavonoid accumulation pattern was also examined in transparent testa mutants blocked at different steps in the flavonoid biosynthesis pathway. The transparent testa mutants were shown to have precursor accumulation patterns similar to those of end product flavonoids in wild-type Landsberg erecta, suggesting that synthesis and end product accumulation occur in the same cells.

  11. Use of magnetite in the production of bricks for heat accumulation. La magnetita en la fabricacion de ladrillos para la acumulacion de calor

    Energy Technology Data Exchange (ETDEWEB)

    Otero de la Gandara, J.L.; Alvarez, P. (Departamento de Ingenieria Quimica, Universidad Complutense de Madrid, Madrid (Spain))

    1994-01-01

    The general aspects concerning the domestic heating by means of ceramic heat-accumulators are reviewed. The heat transfer and the properties of the materials which are to be used are considered as well as the design characteristics of the commercial equipment. Special attention is devoted to the operation at the several stages in the production processes of Fe[sub 2]O[sub 3] ceramic components to be used as heat-accumulators. Magnetite is taken as a raw material. Finally, some possible improvements are presented to achieve the optimization of heat-accumulators equipment by taking advantage of the thermal and mechanical properties of the ceramic materials. (Author) 13 refs.

  12. Carbon Calculator for Land Use Change from Biofuels Production (CCLUB). Users' Manual and Technical Documentation

    Energy Technology Data Exchange (ETDEWEB)

    Dunn, Jennifer B. [Argonne National Lab. (ANL), Argonne, IL (United States); Qin, Zhangcai [Argonne National Lab. (ANL), Argonne, IL (United States); Mueller, Steffen [Univ. of Illinois at Chicago, Chicago, IL (United States); Kwon, Ho-young [International Food Policy Research Institute (IFPRI), Washington, DC (United States); Wander, Michelle M. [Univ. of Illinois, Urbana-Champaign, IL (United States); Wang, Michael [Argonne National Lab. (ANL), Argonne, IL (United States)

    2014-09-01

    The Carbon Calculator for Land Use Change from Biofuels Production (CCLUB) calculates carbon emissions from land use change (LUC) for four different ethanol production pathways including corn grain ethanol and cellulosic ethanol from corn stover, Miscanthus, and switchgrass. This document discusses the version of CCLUB released September 30, 2014 which includes corn and three cellulosic feedstocks: corn stover, Miscanthus, and switchgrass.

  13. Review of Axial Burnup Distribution Considerations for Burnup Credit Calculations

    International Nuclear Information System (INIS)

    Wagner, J.C.; DeHart, M.D.

    2000-01-01

    This report attempts to summarize and consolidate the existing knowledge on axial burnup distribution issues that are important to burnup credit criticality safety calculations. Recently released Nuclear Regulatory Commission (NRC) staff guidance permits limited burnup credit, and thus, has prompted resolution of the axial burnup distribution issue. The reactivity difference between the neutron multiplication factor (keff) calculated with explicit representation of the axial burnup distribution and keff calculated assuming a uniform axial burnup is referred to as the ''end effect.'' This end effect is shown to be dependent on many factors, including the axial-burnup profile, total accumulated burnup, cooling time, initial enrichment, assembly design, and the isotopics considered (i.e., actinide-only or actinides plus fission products). Axial modeling studies, efforts related to the development of axial-profile databases, and the determination of bounding axial profiles are also discussed. Finally, areas that could benefit from further efforts are identified

  14. Accumulation of sunscreen in human skin after daily applications

    DEFF Research Database (Denmark)

    Bodekær, Mette; Akerström, Ulf; Wulf, Hans Christian

    2012-01-01

    Sunscreen applied to the skin provides a considerable sun protection factor (SPF) even after 8 h. Sunscreen use for consecutive days may therefore result in an accumulation of the product. This study investigated the consequences of accumulation for SPF....

  15. The prediction of minor actinides amounts accumulated in the spent fuel in China

    International Nuclear Information System (INIS)

    Zhou Peide

    2000-01-01

    The amounts of the Minor Actinides accumulated in the spent fuel are predicted according to the Nuclear Power Plant development plan envisaged in China. The Minor Actinides generated in the spent fuel unloaded from a typical PWR per year are calculated. The decay characteristics of the Minor Actinides during storage and cooling period are also calculated. At last, the Minor Actinides amounts accumulated in all spent fuel which were unloaded before sometime are given

  16. The role of the shot effect in the accumulation of nuclide masses and activities in the thermal reactor core

    International Nuclear Information System (INIS)

    Nepoleao, P.; Rudak, E.; Wiley, J.

    1998-01-01

    A method is proposed for estimating masses and activities of nuclides in the thermal reactor core with an arbitrary dependence of specific masses on the burnout depth. The method takes into account the statistical character of micro processes accompanying the fuel burning out and accumulation of fission and activation products. For the RBMK reactor of Chernobyl NPP the method gives practically the same results as exact numerical calculations. (author)

  17. The rationale for selecting the method of calculation of project products coast (works, services

    Directory of Open Access Journals (Sweden)

    O. V. Molchanova

    2017-01-01

    Full Text Available In modern conditions of management it is necessary to develop a number of recommendations on the introduction of management accounting at state-owned enterprises that carry out revenue-generating activities or based on the right of economic management. It is necessary to apply the correct cost-accounting method for the production of products, works, services for a more rational calculation of the cost price. This will allow management personnel to receive timely objective information about their cost price, identify the feasibility of production and sales, justify the assortment, plan profits. The procedure for determining the cost price of the project products (works, services in the theory and practice of the state enterprise of the Astrakhan region “Kasprybproekt” is investigated in the work. With the existing practice of planning in design organizations, the planned cost price of design and survey works for established cost items is planned in the cost estimate for production by the design organization as a whole and by the types of work: design, survey and others, without subdividing it by orders (projects. According to this, accounting of the actual costs for work in the design organizations is based. The study showed that the state enterprise of the Astrakhan region “Kasprybproyekt” performs different projects with different execution periods; therefore, it is advisable to use one method of calculating the cost price - job (order costing method, and link it to the responsibility centers depending on the department of the performer. Based on the research of the used method to the cost price calculate of the project products (works, services in the state enterprise of the Astrakhan region “Kasprybproekt”, it was proposed to use the job (order costing method that allows to detail all the project costs without distorting the final financial result and optimize the project costs. If the calculation method is correctly determined

  18. Accumulation of advanced glycation end-products and activation of the SCAP/SREBP Lipogenetic pathway occur in diet-induced obese mouse skeletal muscle.

    Directory of Open Access Journals (Sweden)

    Raffaella Mastrocola

    Full Text Available Aim of this study was to investigate whether advanced glycation end-products (AGEs accumulate in skeletal myofibers of two different animal models of diabesity and whether this accumulation could be associated to myosteatosis. Male C57Bl/6j mice and leptin-deficient ob/ob mice were divided into three groups and underwent 15 weeks of dietary manipulation: standard diet-fed C57 group (C57, n = 10, high-fat high-sugar diet-fed C57 group (HFHS, n = 10, and standard diet-fed ob/ob group (OB/OB, n = 8. HFHS mice and OB/OB mice developed glycometabolic abnormalities in association with decreased mass of the gastrocnemius muscle, fast-to-slow transition of muscle fibers, and lipid accumulation (that occurred preferentially in slow compared to fast fibers. Moreover, we found in muscle fibers of HFHS and OB/OB mice accumulation of AGEs that was preferential for the lipid-accumulating cells, increased expression of the lipogenic pathway SCAP/SREBP, and co-localisation between AGEs and SCAP-(hyperexpressing cells (suggestive for SCAP glycosylation. The increased expression of the SCAP/SREBP lipogenic pathway in muscle fibers is a possible mechanism underlying lipid accumulation and linking myosteatosis to muscle fiber atrophy and fast-to-slow transition that occur in response to diabesity.

  19. Development of HyPEP, A Hydrogen Production Plant Efficiency Calculation Program

    International Nuclear Information System (INIS)

    Lee, Young Jin; Park, Ji Won; Lee, Won Jae; Shin, Young Joon; Kim, Jong Ho; Hong, Sung Deok; Lee, Seung Wook; Hwang, Moon Kyu

    2007-12-01

    Development of HyPEP program for assessing the steady-state hydrogen production efficiency of the nuclear hydrogen production facilities was carried out. The main developmental aims of the HyPEP program are the extensive application of the GUI for enhanced user friendliness and the fast numerical solution scheme. These features are suitable for such calculations as the optimisation calculations. HyPEP was developed with the object-oriented programming techniques. The components of the facility was modelled as objects in a hierarchical structure where the inheritance property of the object oriented program were extensively applied. The Delphi program language which is based on the Object Pascal was used for the HyPEP development. The conservation equations for the thermal hydraulic flow network were setup and the numerical solution scheme was developed and implemented into HyPEP beta version. HyPEP beta version has been developed with working GUI and the numerical solution scheme implementation. Due to the premature end of this project the fully working version of HyPEP was not produced

  20. Influence of land use on phytomass accumulation in Highland ...

    African Journals Online (AJOL)

    Transformation of indigenous vegetation for production purposes impacts negatively on biodiversity but does this necessarily equate with a decrease in phytomass accumulation, which may influence carbon sequestration? Phytomass accumulation was studied for common land covers of beef ranching or dairy farming ...

  1. Membrane engineering - A novel strategy to enhance the production and accumulation of β-carotene in Escherichia coli.

    Science.gov (United States)

    Wu, Tao; Ye, Lijun; Zhao, Dongdong; Li, Siwei; Li, Qingyan; Zhang, Bolin; Bi, Changhao; Zhang, Xueli

    2017-09-01

    Carotenoids are a class of terpenes of commercial interest that exert important biological functions. While various strategies have been applied to engineer β-carotene production in microbial cell factories, no work has been done to study and improve the storage of hydrophobic terpene products inside the heterologous host cells. Although the membrane is thought to be the cell compartment that accumulates hydrophobic terpenes such as β-carotene, direct evidence is still lacking. In this work, we engineered the membrane of Escherichia coli in both its morphological and biosynthetic aspects, as a means to study and improve its storage capacity for β-carotene. Engineering the membrane morphology by overexpressing membrane-bending proteins resulted in a 28% increase of β-carotene specific producton value, while engineering the membrane synthesis pathway led to a 43% increase. Moreover, the combination of these two strategies had a synergistic effect, which caused a 2.9-fold increase of β-carotene specific production value (from 6.7 to 19.6mg/g DCW). Inward membrane stacks were observed in electron microscopy images of the engineered E. coli cells, which indicated that morphological changes were associated with the increased β-carotene storage capacity. Finally, membrane separation and analysis confirmed that the increased β-carotene was mainly accumulated within the cell membrane. This membrane engineering strategy was also applied to the β-carotene hyperproducing strain CAR025, which led to a 39% increase of the already high β-carotene specific production value (from 31.8 to 44.2mg/g DCW in shake flasks), resulting in one of the highest reported specific production values under comparable culture conditions. The membrane engineering strategy developed in this work opens up a new direction for engineering and improving microbial terpene producers. It is quite possible that a wide range of strains used to produce hydrophobic compounds can be further improved

  2. Calculation of the isotope concentrations, source terms and radiation shielding of the SAFARI-1 irradiation products

    International Nuclear Information System (INIS)

    Stoker, C.C.; Ball, G.

    2000-01-01

    The ever increasing expansion of the irradiation product portfolio of the SAFARI-1 reactor leads to the need to routinely calculate the radio-isotope concentrations and source terms for the materials irradiated in the reactor accurately. In addition to this, the required shielding for the transportation and processing of these irradiation products needs to be determined. In this paper the calculational methodology applied is described with special attention given to the spectrum dependence of the one-group cross sections of selected SAFARI-1 irradiation materials and the consequent effect on the determination of the isotope concentrations and source terms. Comparisons of the calculated isotopic concentrations and dose rates with experimental analysis and measurements provide confidence in the calculational methodologies and data used. (author)

  3. Electron-cooled accumulation of $4 × 10^9$ positrons for production and storage of antihydrogen atoms

    CERN Document Server

    Fitzakerley, DW; Hessels, E A; Skinner, T D G; Storry, C H; Weel, M; Gabrielse, G; Hamley, C D; Jones, N; Marable, K; Tardiff, E; Grzonka, D; Oelert, W; Zielinski, M

    2016-01-01

    Four billion positrons (e+) are accumulated in a Penning–Ioffe trap apparatus at 1.2 K and <6 × 10−17 Torr. This is the largest number of positrons ever held in a Penning trap. The e+ are cooled by collisions with trapped electrons (e−) in this first demonstration of using e− for efficient loading of e+ into a Penning trap. The combined low temperature and vacuum pressure provide an environment suitable for antihydrogen ($\\bar{{\\rm{H}}}$) production, and long antimatter storage times, sufficient for high-precision tests of antimatter gravity and of CPT.

  4. Evaluation of fission product worth margins in PWR spent nuclear fuel burnup credit calculations

    International Nuclear Information System (INIS)

    Blomquist, R.N.; Finck, P.J.; Jammes, C.; Stenberg, C.G.

    1999-01-01

    Current criticality safety calculations for the transportation of irradiated LWR fuel make the very conservative assumption that the fuel is fresh. This results in a very substantial overprediction of the actual k eff of the transportation casks; in certain cases, this decreases the amount of spent fuel which can be loaded in a cask, and increases the cost of transporting the spent fuel to the repository. Accounting for the change of reactivity due to fuel depletion is usually referred to as ''burnup credit.'' The US DOE is currently funding a program aimed at establishing an actinide only burnup credit methodology (in this case, the calculated reactivity takes into account the buildup or depletion of a limited number of actinides). This work is undergoing NRC review. While this methodology is being validated on a significant experimental basis, it implicitly relies on additional margins: in particular, the absorption of neutrons by certain actinides and by all fission products is not taken into account. This provides an important additional margin and helps guarantee that the methodology is conservative provided these neglected absorption are known with reasonable accuracy. This report establishes the accuracy of fission product absorption rate calculations: (1) the analysis of European fission product worth experiments demonstrates that fission product cross-sections available in the US provide very good predictions of fission product worth; (2) this is confirmed by a direct comparison of European and US cross section evaluations; (3) accuracy of Spent Nuclear Fuel (SNF) fission product content predictions is established in a recent ORNL report where several SNF isotopic assays are analyzed; and (4) these data are then combined to establish in a conservative manner the fraction of the predicted total fission product absorption which can be guaranteed based on available experimental data

  5. Numerical simulation studies of gas production scenarios from hydrate accumulations at the Mallik Site, McKenzie Delta, Canada

    International Nuclear Information System (INIS)

    Moridis, George J.; Collett, Timothy S.; Dallimore, Scott R.; Satoh, Tohru; Hancock, Stephen; Weatherill, Brian

    2002-01-01

    The Mallik site represents an onshore permafrost-associated gas hydrate accumulation in the Mackenzie Delta, Northwest Territories, Canada. An 1150 m deep gas hydrate research well was drilled at the site in 1998. The objective of this study is the analysis of various gas production scenarios from several gas-hydrate-bearing zones at the Mallik site. The TOUGH2 general-purpose simulator with the EOSHYDR2 module were used for the analysis. EOSHYDR2 is designed to model the non-isothermal CH(sub 4) (methane) release, phase behavior and flow under conditions typical of methane-hydrate deposits by solving the coupled equations of mass and heat balance, and can describe any combination of gas hydrate dissociation mechanisms. Numerical simulations indicated that significant gas hydrate production at the Mallik site was possible by drawing down the pressure on a thin free-gas zone at the base of the hydrate stability field. Gas hydrate zones with underlying aquifers yielded significant gas production entirely from dissociated gas hydrate, but large amounts of produced water. Lithologically isolated gas-hydrate-bearing reservoirs with no underlying free gas or water zones, and gas-hydrate saturations of at least 50% were also studied. In these cases, it was assumed that thermal stimulation by circulating hot water in the well was the method used to induce dissociation. Sensitivity studies indicated that the methane release from the hydrate accumulations increases with gas-hydrate saturation, the initial formation temperature, the temperature of the circulating water in the well, and the formation thermal conductivity. Methane production appears to be less sensitive to the rock and hydrate specific heat and permeability of the formation

  6. Accumulation and health risk of heavy metals in vegetables from harmless and organic vegetable production systems of China.

    Science.gov (United States)

    Chen, Yong; Hu, Wenyou; Huang, Biao; Weindorf, David C; Rajan, Nithya; Liu, Xiaoxiao; Niedermann, Silvana

    2013-12-01

    Heavy metal accumulation in vegetables is a growing concern for public health. Limited studies have elucidated the heavy metal accumulation characteristics and health risk of different vegetables produced in different facilities such as greenhouses and open-air fields and under different management modes such as harmless and organic. Given the concern over the aforementioned factors related to heavy metal accumulation, this study selected four typical greenhouse vegetable production bases, short-term harmless greenhouse vegetable base (SHGVB), middle-term harmless greenhouse vegetable base (MHGVB), long-term harmless greenhouse vegetable base (LHGVB), and organic greenhouse vegetable base (OGVB), in Nanjing City, China to study heavy metal accumulation in different vegetables and their associated health risks. Results showed that soils and vegetables from SHGVB and OGVB apparently accumulated fewer certain heavy metals than those from other bases, probably due to fewer planting years and special management, respectively. Greenhouse conditions significantly increased certain soil heavy metal concentrations relative to open-air conditions. However, greenhouse conditions did not significantly increase concentrations of As, Cd, Cu, Hg, and Zn in leaf vegetables. In fact, under greenhouse conditions, Pb accumulation was effectively reduced. The main source of soil heavy metals was the application of large amounts of low-grade fertilizer. There was larger health risk for producers' children to consume vegetables from the three harmless vegetable bases than those of residents' children. The hazard index (HI) over a large area exceeded 1 for these two kinds of children in the MHGVB and LHGVB. There was also a slight risk in the SHGVB for producers' children solely. However, the HI of the whole area of the OGVB for two kinds of children was below 1, suggesting low risk of heavy metal exposure through the food chain. Notably, the contribution rate of Cu and Zn to the HI were

  7. Neutral lipid accumulation at elevated temperature in conditional mutants of two microalgae species

    DEFF Research Database (Denmark)

    Yao, Shuo; Brandt, Anders Bøving; Egsgaard, Helge

    2012-01-01

    Triacylglycerols, an energy storage compound in microalgae, are known to be accumulated after nitrogen starvation of microalgae cells. Microalgae could be of importance for future biodiesel production due to their fast growth rate and high oil content. In collections of temperature sensitive...... accumulation in microalgae and suggest possibilities for biodiesel production by specific induction of lipid accumulation in miroalgal cultures by cell-cycle inhibition....

  8. Eugenol stimulates lactate accumulation yet inhibits volatile fatty acid production and eliminates coliform bacteria in cattle and swine waste.

    Science.gov (United States)

    Varel, V H; Miller, D L

    2004-01-01

    To determine how eugenol affects fermentation parameters and faecal coliforms in cattle and swine waste slurries stored anaerobically. Waste slurries (faeces:urine:water, 50:35:15) were blended with and without additives and aliquoted to triplicate 1-l flasks. Faecal coliforms were eliminated in cattle and swine waste slurries within 1 or 2 days with additions of eugenol at 10.05 mm (0.15%) and 16.75 mm (0.25%). At these concentrations volatile fatty acids (VFA) were reduced ca 70 and 50% in cattle and swine waste, respectively, over 6-8 weeks. Additionally, in cattle waste, eugenol stimulated the accumulation of lactate (>180 mm) when compared with thymol treatment (20 mm lactate). In swine waste, lactate accumulation did not occur without additives; eugenol and thymol stimulated lactate accumulation to concentrations of 22 and 32 mm, respectively. Eugenol added to cattle waste may be more beneficial than thymol because not only does it effectively control faecal coliforms and odour (VFA production), it also stimulates lactate accumulation. This in turn, causes the pH to drop more rapidly, further inhibiting microbial activity and nutrient emissions. Plant essential oils have the potential to solve some of the environmental problems associated with consolidated animal feeding operations. Thymol and eugenol reduce fermentative activity, thus, have the potential to reduce emissions of greenhouse gases and odour, and curtail transmission of pathogens in cattle and swine wastes.

  9. THE DEPENDENCE OF GLYCEROL ACCUMULATION AND STARCH HYDROLYZATES FERMENTATION FROM WORT CONCENTRATION

    Directory of Open Access Journals (Sweden)

    Оliynichuk S. Т.

    2015-08-01

    Full Text Available The purpose of this work is to study the dependence of ethanol accumulation by-products and secondary products (glycerol and propionic acid during the fermentation in the case of increasing the wort concentration from 12 to 21% by weight of sugar as an example of commonly used in the alcohol industry the commercial dry yeast company “Danisco” and experimental osmophilic strain Saccharomyces cerevisiae DS-02-E, isolated from a concentrated (80% DM of rye malt wort which spontaneously fermented. The enzyme preparations “AMYLEX 4T”, “ALPHALASE AFP” and “DIAZYME SSF” were used for the liquefaction and saccharification of starch wort. The finished industrial of both yeast strains were added to the fermentation flasks in an amount of 10% by volume of the primary wort. In the mature brew the unfermented carbohydrates content was determined by colorimetric method with anthrone reagent, alcohol — by glass areometer-alcoholometer, acidity — potentiometrically, the concentration of dry matter — by areometer, glycerol content — by photocolorimetry method. In the brew distillate a volatile impurities content, namely propionic acid, was determined using gas chromatography. Statistical processing of the results of three series of experiments were carried out by calculating the arithmetical mean value of 5 measurements, their standard deviations and errors. To determine the probable differences between the mean values were used Student’s t test. Differences were considered statistically significant at P < 0.05. Reduction for accumulation of glycerol (between 38 till 53% at higher concentrations of nutrient medium in the case of the yeast Saccharomyces cerevisiae DS-02-E as compared with commercial dry yeast, reduction the formation of unwanted by-product of fermentation — propionic acid (up to 34%, a better ability of the experimental strain to accumulate sugar of wort and to accumulate ethanol (up to 0.1–0.25% vol. were shown. It

  10. Response of stored potato seed tubers from contrasting cultivars to accumulated day-degrees

    NARCIS (Netherlands)

    Struik, P.C.; Putten, van der P.E.L.; Caldiz, D.O.; Scholte, K.

    2006-01-01

    In potato (Solanum tuberosum L.), the accumulated day-degrees (temperature sum, calculated by accumulating the daily temperatures) from dormancy break until seed tuber use has been suggested as an indicator of the physiological status of the seed. We tested whether similar temperature sums differing

  11. Calculation of displacement and helium production at the Clinton P. Anderson Los Alamos Meson Physics Facility (LAMPF) irradiation facility

    International Nuclear Information System (INIS)

    Wechsler, M.S.; Davidson, D.R.; Greenwood, L.R.; Sommer, W.F.

    1984-01-01

    CT: Differential and total displacement and helium production rates are calculated for copper irradiated by spallation neutrons and 760 MeV protons at the Clinton P. Anderson Los Alamos Meson Physics Facility (LAMPF). The calculations are performed using the SPECTER and VNMTC computer codes, the latter being specially designed for spallation radiation damage calculations. For comparison, similar SPECTER calculations are also described for irradiation of copper in EBR-II and RTNS-II. The results indicate substantial contributions to the displacement and helium production rates due to neutrons in the high-energy tail (above 20 MeV) of the LAMPF spallation neutron spectrum. Still higher production rates are calculated for irradiations in the direct proton beam. These results will provide useful background information for research to be conducted at a new irradiation facility at LAMPF

  12. Modelling of space-charge accumulation process in dielectrics of MDS structures under irradiation

    International Nuclear Information System (INIS)

    Gurtov, V.A.; Nazarov, A.I.; Travkov, I.V.

    1990-01-01

    Results of numerical modelling of radiation-induced space charge (RISC) accumulation in MOS structure silicon dioxide are given. Diffusion-drift model which takes account of trap heterogeneous distribution within dielectric volume and channeling of carriers captured at traps represents basis for calculations. Main physical processes affecting RISC accumulation are picked out and character of capture filling in dielectric volume under stress in MOS structure shutter during irradiation on the basis of comparison of experimental results for different thickness oxides with calculation data are predicted

  13. Ordinary differential equation for local accumulation time.

    Science.gov (United States)

    Berezhkovskii, Alexander M

    2011-08-21

    Cell differentiation in a developing tissue is controlled by the concentration fields of signaling molecules called morphogens. Formation of these concentration fields can be described by the reaction-diffusion mechanism in which locally produced molecules diffuse through the patterned tissue and are degraded. The formation kinetics at a given point of the patterned tissue can be characterized by the local accumulation time, defined in terms of the local relaxation function. Here, we show that this time satisfies an ordinary differential equation. Using this equation one can straightforwardly determine the local accumulation time, i.e., without preliminary calculation of the relaxation function by solving the partial differential equation, as was done in previous studies. We derive this ordinary differential equation together with the accompanying boundary conditions and demonstrate that the earlier obtained results for the local accumulation time can be recovered by solving this equation. © 2011 American Institute of Physics

  14. Spin accumulation in disordered topological insulator ultrathin films

    Science.gov (United States)

    Siu, Zhuo Bin; Ho, Cong Son; Tan, Seng Ghee; Jalil, Mansoor B. A.

    2017-08-01

    Topological insulator (TI) ultrathin films differ from the more commonly studied semi-infinite bulk TIs in that the former possess both top and bottom surfaces where the surface states localized at different surfaces can couple to one another across the finite thickness of the film. In the presence of an in-plane magnetization, the TI thin films display two distinct phases depending on which of the inter-surface coupling or the magnetization is stronger. In this work, we consider a Bi2Se3 TI thin film system with an in-plane magnetization and numerically calculate the resulting spin accumulation on both surfaces of the film due to an in-plane electric field to linear order. We describe a numerical scheme for performing the Kubo formula calculation in which we include impurity scattering and vertex corrections. We find that the sums of the spin accumulation over the two surfaces in the in-plane direction perpendicular to the magnetization and in the out of plane direction are antisymmetric in Fermi energy around the charge neutrality point and are non-vanishing only when the symmetry between the top and bottom TI surfaces is broken. The impurity scattering, in general, diminishes the magnitude of the spin accumulation.

  15. Effects of dust accumulation and module cleaning on performance ratio of solar rooftop system and solar power plants

    Science.gov (United States)

    Sakarapunthip, Nattakarn; Chenvidhya, Dhirayut; Chuangchote, Surawut; Kirtikara, Krissanapong; Chenvidhya, Tanokkorn; Onreabroy, Wandee

    2017-08-01

    Thailand is an agricultural country, with rice, sugar, and cassava as the major export products. Production of rice, sugar cane, and cassava entails agricultural activities that give rise to significant airborne dusts. In this work, five photovoltaic (PV) units (one solar rooftop and four power plants) are selected for the study. From the study of dust accumulation on glass surface located near rice farms, it was found that opaque areas due to the deposition of dust are 11-14% after 1-2-week exposure. As a consequence, PV system performance is affected. Performance ratio was calculated to determine these effects. Overall results reveal that during the dry and hot seasons, dust deposition significantly affects the performance ratio. The performance ratio reduces by 1.6-3% for 1-month dust accumulation and reduces by 6-8% for 2-month dust accumulation. After cleaning the dust accumulated, the performance ratio greatly increases, resulting in the increase in the energy output by 10%. This increase provides economic and cost benefits of PV cleaning. The performance ratio is not significantly changed during the rainy season, which PV modules are relatively clean as the dust is washed away by rain. It was also found that most of the solar power plants in Thailand still rely on manual cleaning of PV modules with washing water followed by wiping. However, only one power plant, employs a machine for cleaning, resulting in lower cleaning costs.

  16. A Sample Calculation of Tritium Production and Distribution at VHTR by using TRITGO Code

    International Nuclear Information System (INIS)

    Park, Ik Kyu; Kim, D. H.; Lee, W. J.

    2007-03-01

    TRITGO code was developed for estimating the tritium production and distribution of high temperature gas cooled reactor(HTGR), especially GTMHR350 by General Atomics. In this study, the tritium production and distribution of NHDD was analyzed by using TRITGO Code. The TRITGO code was improved by a simple method to calculate the tritium amount in IS Loop. The improved TRITGO input for the sample calculation was prepared based on GTMHR600 because the NHDD has been designed referring GTMHR600. The GTMHR350 input with related to the tritium distribution was directly used. The calculated tritium activity among the hydrogen produced in IS-Loop is 0.56 Bq/g- H2. This is a very satisfying result considering that the limited tritium activity of Japanese Regulation Guide is 5.6 Bq/g-H2. The basic system to analyze the tritium production and the distribution by using TRITGO was successfully constructed. However, there exists some uncertainties in tritium distribution models, the suggested method for IS-Loop, and the current input was not for NHDD but for GTMHR600. The qualitative analysis for the distribution model and the IS-Loop model and the quantitative analysis for the input should be done in the future

  17. A Sample Calculation of Tritium Production and Distribution at VHTR by using TRITGO Code

    Energy Technology Data Exchange (ETDEWEB)

    Park, Ik Kyu; Kim, D. H.; Lee, W. J

    2007-03-15

    TRITGO code was developed for estimating the tritium production and distribution of high temperature gas cooled reactor(HTGR), especially GTMHR350 by General Atomics. In this study, the tritium production and distribution of NHDD was analyzed by using TRITGO Code. The TRITGO code was improved by a simple method to calculate the tritium amount in IS Loop. The improved TRITGO input for the sample calculation was prepared based on GTMHR600 because the NHDD has been designed referring GTMHR600. The GTMHR350 input with related to the tritium distribution was directly used. The calculated tritium activity among the hydrogen produced in IS-Loop is 0.56 Bq/g- H2. This is a very satisfying result considering that the limited tritium activity of Japanese Regulation Guide is 5.6 Bq/g-H2. The basic system to analyze the tritium production and the distribution by using TRITGO was successfully constructed. However, there exists some uncertainties in tritium distribution models, the suggested method for IS-Loop, and the current input was not for NHDD but for GTMHR600. The qualitative analysis for the distribution model and the IS-Loop model and the quantitative analysis for the input should be done in the future.

  18. Effective Dose Calculation Program (EDCP) for the usage of NORM-added consumer product.

    Science.gov (United States)

    Yoo, Do Hyeon; Lee, Jaekook; Min, Chul Hee

    2018-04-09

    The aim of this study is to develop the Effective Dose Calculation Program (EDCP) for the usage of Naturally Occurring Radioactive Material (NORM) added consumer products. The EDCP was developed based on a database of effective dose conversion coefficient and the Matrix Laboratory (MATLAB) program to incorporate a Graphic User Interface (GUI) for ease of use. To validate EDCP, the effective dose calculated with EDCP by manually determining the source region by using the GUI and that by using the reference mathematical algorithm were compared for pillow, waist supporter, eye-patch and sleeping mattress. The results show that the annual effective dose calculated with EDCP was almost identical to that calculated using the reference mathematical algorithm in most of the assessment cases. With the assumption of the gamma energy of 1 MeV and activity of 1 MBq, the annual effective doses of pillow, waist supporter, sleeping mattress, and eye-patch determined using the reference algorithm were 3.444 mSv year -1 , 2.770 mSv year -1 , 4.629 mSv year -1 , and 3.567 mSv year -1 , respectively, while those calculated using EDCP were 3.561 mSv year -1 , 2.630 mSv year -1 , 4.740 mSv year -1 , and 3.780 mSv year -1 , respectively. The differences in the annual effective doses were less than 5%, despite the different calculation methods employed. The EDCP can therefore be effectively used for radiation protection management in the context of the usage of NORM-added consumer products. Additionally, EDCP can be used by members of the public through the GUI for various studies in the field of radiation protection, thus facilitating easy access to the program. Copyright © 2018. Published by Elsevier Ltd.

  19. Matter accumulation and changes of assimilation product transport and carbohydrate regime in barley plants as induced by infection with Puccinia striiformis West

    Energy Technology Data Exchange (ETDEWEB)

    Schubert, J. (Akademie der Landwirtschaftswissenschaften der DDR, Aschersleben. Inst. fuer Phytopathologie)

    1982-01-01

    Accumulation of nuclides (/sup 32/P, /sup 14/C), /sup 14/CO/sub 2/ assimilation and /sup 14/C transport were studied in several barley cultivars differing in their resistance to yellow rust. Increased matter accumulation was found in the rust pustules. Mycelium was proved by means of autoradiography. Infection causes changes with regard to /sup 14/CO/sub 2/ assimilation, carbohydrate regime and transport of /sup 14/C assimilation products. Certain relationships exist between these changes and plant resistance to yellow rust. During germination the rust uredospores release substances, particularly amino acids, to be transported in the plant.

  20. 3D and 1D calculation of hysteresis loops and energy products for anisotropic nanocomposite films with perpendicular anisotropy

    International Nuclear Information System (INIS)

    Yuan, X.H.; Zhao, G.P.; Yue, Ming; Ye, L.N.; Xia, J.; Zhang, X.C.; Chang, J.

    2013-01-01

    In this paper, the magnetic reversal process, hysteresis loops and energy products for exchange-coupled Nd 2 Fe 14 B/α-Fe bilayers are studied systematically by a three-dimensional (3D) model. The 3D calculations are numerically solved using the finite difference method, where the results are carefully compared with those calculated by one-dimensional (1D) model. It is found that the calculated hysteresis loops and energy products based on the two methods are consistent with each other. Both nucleation fields and coercivities decrease monotonically as the soft layer thickness L s increases. In addition, the calculated spatial distributions of magnetization orientations in the thickness direction at various applied fields based on both methods signify a three-step magnetic reversal process, which are nucleation, growth and displacement of the domain wall. The calculated magnetic orientations within the film plane, however, are totally different according to the two methods. The 3D calculation exhibits a process of vortex formation and annihilation. On the other hand, the 1D calculation gives a quasi-coherent one, where magnetization orientation is coherent in the film plane and varies in the thickness direction. This new reversal mechanism displayed in the film plane has a systematic influence on the nucleation fields, coercivity and energy products. - Highlights: • Consistent hysteresis loops and energy products for 3D and 1D calculation. • Domain wall formation, evolution and displacement perpendicular to the film plane. • Vortex formation, annihilation and better loop squareness in 3D calculation. • Larger nucleation fields, remanence and smaller coercivity in 3D calculation

  1. Cracked pellet gap conductance model: comparison of FRAP-S calculations with measured fuel centerline temperatures

    International Nuclear Information System (INIS)

    MacDonald, P.E.; Broughton, J.M.

    1975-03-01

    Fuel pellets crack extensively upon irradiation due both to thermal stresses induced by power changes and at high burnup, to accumulation of gaseous fission products at grain boundaries. Therefore, the distance between the fuel and cladding will be circumferentially nonuniform; varying between that calculated for intact operating fuel pellets and essentially zero (fuel segments in contact with the cladding wall). A model for calculation of temperatures in cracked pellets is proposed wherein the effective fuel to cladding gap conductance is calculated by taking a zero pressure contact conductance in series with an annular gap conductance. Comparisons of predicted and measured fuel centerline temperatures at beginning of life and at extended burnup are presented in support of the model. 13 references

  2. Products cooked in preheated versus non-preheated ovens. Baking times, calculated energy consumption, and product quality compared.

    Science.gov (United States)

    Odland, D; Davis, C

    1982-08-01

    Plain muffins, yellow cake, baked custard, apple pie, tuna casserole, frozen tuna casserole, cheese soufflé, and meat loaf were baked in preheated and non-preheated standard gas, continuous-clean gas, standard electric, and self-cleaning electric ovens. Products generally required 5 min. or less extra baking time when cooked in non-preheated rather than in preheated ovens. The variability in baking times often was less between preheated and non-preheated ovens than among oven types. Calculated energy consumption values showed that usually less energy was required to bake products in non-preheated than in preheated ovens; savings averaged about 10 percent. Few significant differences were found in physical measurements or eating quality either between preheated and non-preheated ovens or among oven types. Overall, for the products tested, findings confirmed that preheating the oven is not essential for good product quality and, therefore, is an unnecessary use of energy.

  3. Stontium-90 contamination in vegetation from radioactive waste seepage areas at ORNL, and theoretical calculations of 90Sr accumulation by deer

    International Nuclear Information System (INIS)

    Garten, C.T. Jr.; Lomax, R.D.

    1987-06-01

    This report describes data obtained during a preliminary characterization of 90 Sr levels in browse vegetation from the vicinity of seeps adjacent to ORNL solid waste storage areas (SWSA) where deer (Odocoileus virginianus) were suspected to accumulate 90 Sr through the food chain. The highest strontium concentrations in plant samples were found at seeps associated with SWSA-5. Strontium-90 concentrations in honeysuckle and/or blackberry shoots from two seeps in SWSA-5 averaged 39 and 19 nCi/g dry weight (DW), respectively. The maximum concentration observed was 90 nCi/g DW. Strontium-90 concentrations in honeysuckle and blackberry shoots averaged 7.4 nCi/g DW in a study area south of SWSA-4, and averaged 1.0 nCi/g DW in fescue grass from a seepage area located on SWSA-4. A simple model (based on metabolic data for mule deer) has been used to describe the theoretical accumulation of 90 Sr in bone of whitetail deer following ingestion of contaminated vegetation. These model calculations suggest that if 30 pCi 90 Sr/g deer bone is to be the accepted screening level for retaining deer killed on the reservation, then 5-pCi 90 Sr/g DW vegetation should be considered as a possible action level in making decisions about the need for remedial measures, because unrestricted access and full utilization of vegetation contaminated with 90 Sr bone concentrations of <30 pCi/g in a 45-kg buck

  4. Application of the discounted value flows method in production cost calculations for Czechoslovak nuclear power plants

    International Nuclear Information System (INIS)

    Majer, P.

    1990-01-01

    The fundamentals are outlined of the discounted value flows method, which is used in industrial countries for calculating the specific electricity production costs. Actual calculations were performed for the first two units of the Temelin nuclear power plant. All costs associated with the construction, operation and decommissioning of this nuclear power plant were taken into account. With a high degree of certainty, the specific production costs of the Temelin nuclear power plant will lie within the range of 0.32 to 0.36 CSK/kWh. Nearly all results of the sensitivity analysis performed for the possible changes in the input values fall within this range. An increase in the interest rate to above 8% is an exception; this, however, can be regarded as rather improbable on a long-term basis. Sensitivity analysis gave evidence that the results of the electricity production cost calculations for the Temelin nuclear power plant can be considered sufficiently stable. (Z.M.). 7 figs., 2 tabs., 14 refs

  5. Radcalc: A computer program to calculate the radiolytic production of hydrogen gas from radioactive wastes in packages

    International Nuclear Information System (INIS)

    Green, J.R.; Schwarz, R.A.; Hillesland, K.E.; Roetman, V.E.; Field, J.G.

    1995-11-01

    Radcalc for Windows' is a menu-driven Microsoft2 Windows-compatible computer code that calculates the radiolytic production of hydrogen gas in high- and low-level radioactive waste. In addition, the code also determines US Department of Transportation (DOT) transportation classifications, calculates the activities of parent and daughter isotopes for a specified period of time, calculates decay heat, and calculates pressure buildup from the production of hydrogen gas in a given package geometry. Radcalc for Windows was developed by Packaging Engineering, Transportation and Packaging, Westinghouse Hanford Company, Richland, Washington, for the US Department of Energy (DOE). It is available from Packaging Engineering and is issued with a user's manual and a technical manual. The code has been verified and validated

  6. Model-based intensification of a fed-batch microbial process for the maximization of polyhydroxybutyrate (PHB) production rate.

    Science.gov (United States)

    Penloglou, Giannis; Vasileiadou, Athina; Chatzidoukas, Christos; Kiparissides, Costas

    2017-08-01

    An integrated metabolic-polymerization-macroscopic model, describing the microbial production of polyhydroxybutyrate (PHB) in Azohydromonas lata bacteria, was developed and validated using a comprehensive series of experimental measurements. The model accounted for biomass growth, biopolymer accumulation, carbon and nitrogen sources utilization, oxygen mass transfer and uptake rates and average molecular weights of the accumulated PHB, produced under batch and fed-batch cultivation conditions. Model predictions were in excellent agreement with experimental measurements. The validated model was subsequently utilized to calculate optimal operating conditions and feeding policies for maximizing PHB productivity for desired PHB molecular properties. More specifically, two optimal fed-batch strategies were calculated and experimentally tested: (1) a nitrogen-limited fed-batch policy and (2) a nitrogen sufficient one. The calculated optimal operating policies resulted in a maximum PHB content (94% g/g) in the cultivated bacteria and a biopolymer productivity of 4.2 g/(l h), respectively. Moreover, it was demonstrated that different PHB grades with weight average molecular weights of up to 1513 kg/mol could be produced via the optimal selection of bioprocess operating conditions.

  7. The design of coils for the production of high homogeneous fields; Calcul des bobinages pour la production de champs magnetiques tres homogenes

    Energy Technology Data Exchange (ETDEWEB)

    Desportes, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    The discovery of type II superconductors has considerably increased the possibilities of air-core coils, in particular with regard to the production of high homogeneous fields. The design of such magnets,calls for elaborate calculations which, in practise, can only be carried out on computers. The present report describes a complete set of programs for the calculation, in the case of cylindrical systems, of the magnetic field components at any point, the lines of flux, the forces, the self and mutual inductances, as well as the design of compensated coils for the production of high homogeneous fields. These programs have been employed for the calculation of two magnets which are described in detail. (author) [French] L'interet des bobines sans fer s'est considerablement accru depuis l'apparition recente des supraconducteurs de la deuxieme espece, en particulier pour la realisation d'aimants a champ tres homogene. Le calcul de tels bobinages fait appel a des methodes complexes dont l'execution pratique necessite l'emploi de machines a calculer. Le present rapport decrit un ensemble de programmes permettant de calculer, dans le cas de systemes de revolution de structure quelconque, le champ dans tout l'espace, les lignes de force du champ, les efforts electromagnetiques, les selfs et mutuelles, et de determiner des enroulements de compensation destines a uniformiser le champ. Ces programmes ont servi au calcul de deux aimants particuliers dont les caracteristiques detaillees sont fournies a titre d'application. (auteur)

  8. Differentially Encoded LDPC Codes—Part I: Special Case of Product Accumulate Codes

    Directory of Open Access Journals (Sweden)

    (Tiffany JingLi

    2008-01-01

    Full Text Available Part I of a two-part series investigates product accumulate codes, a special class of differentially-encoded low density parity check (DE-LDPC codes with high performance and low complexity, on flat Rayleigh fading channels. In the coherent detection case, Divsalar's simple bounds and iterative thresholds using density evolution are computed to quantify the code performance at finite and infinite lengths, respectively. In the noncoherent detection case, a simple iterative differential detection and decoding (IDDD receiver is proposed and shown to be robust for different Doppler shifts. Extrinsic information transfer (EXIT charts reveal that, with pilot symbol assisted differential detection, the widespread practice of inserting pilot symbols to terminate the trellis actually incurs a loss in capacity, and a more efficient way is to separate pilots from the trellis. Through analysis and simulations, it is shown that PA codes perform very well with both coherent and noncoherent detections. The more general case of DE-LDPC codes, where the LDPC part may take arbitrary degree profiles, is studied in Part II Li 2008.

  9. Implementation of a Thermodynamic Solver within a Computer Program for Calculating Fission-Product Release Fractions

    Science.gov (United States)

    Barber, Duncan Henry

    During some postulated accidents at nuclear power stations, fuel cooling may be impaired. In such cases, the fuel heats up and the subsequent increased fission-gas release from the fuel to the gap may result in fuel sheath failure. After fuel sheath failure, the barrier between the coolant and the fuel pellets is lost or impaired, gases and vapours from the fuel-to-sheath gap and other open voids in the fuel pellets can be vented. Gases and steam from the coolant can enter the broken fuel sheath and interact with the fuel pellet surfaces and the fission-product inclusion on the fuel surface (including material at the surface of the fuel matrix). The chemistry of this interaction is an important mechanism to model in order to assess fission-product releases from fuel. Starting in 1995, the computer program SOURCE 2.0 was developed by the Canadian nuclear industry to model fission-product release from fuel during such accidents. SOURCE 2.0 has employed an early thermochemical model of irradiated uranium dioxide fuel developed at the Royal Military College of Canada. To overcome the limitations of computers of that time, the implementation of the RMC model employed lookup tables to pre-calculated equilibrium conditions. In the intervening years, the RMC model has been improved, the power of computers has increased significantly, and thermodynamic subroutine libraries have become available. This thesis is the result of extensive work based on these three factors. A prototype computer program (referred to as SC11) has been developed that uses a thermodynamic subroutine library to calculate thermodynamic equilibria using Gibbs energy minimization. The Gibbs energy minimization requires the system temperature (T) and pressure (P), and the inventory of chemical elements (n) in the system. In order to calculate the inventory of chemical elements in the fuel, the list of nuclides and nuclear isomers modelled in SC11 had to be expanded from the list used by SOURCE 2.0. A

  10. Disposal of Low-Activity Waste and Accumulation in Cultivated Soils

    International Nuclear Information System (INIS)

    Barbier, G.; Michon, G.

    1960-01-01

    The paper describes a method of accumulating long-lived radioisotopes in soils and calculating the maximum contamination they would cause in vegetables grown on these soils. The authors suggest a way of expressing this contamination and a formula by which the maximum contamination of one kilogramme of the harvested produce in relation to the tolerated contamination per litre of irrigation water could be calculated. (author) [fr

  11. Disposal of Low-Activity Waste and Accumulation in Cultivated Soils

    Energy Technology Data Exchange (ETDEWEB)

    Baubier, G. [Central Agricultural Research Station, Versailles (France); Michon, G. [Atomic Health Physics Service, Saclay Nuclear Research Centre (France)

    1960-07-01

    The paper describes a method of accumulating long-lived radioisotopes in soils and calculating the maximum contamination they would cause in vegetables grown on these soils. The authors suggest a way of expressing this contamination and a formula by which the maximum contamination of one kilogramme of the harvested produce in relation to the tolerated contamination per litre of irrigation water could be calculated. (author)

  12. The influence of L-DOPA on the accumulation of lipid peroxidation products in some brain structures affected by radiation

    International Nuclear Information System (INIS)

    Babaev, R.A.; Kocharli, R.Kh.; Akhmedova, G.Sh.; Gasanova, A.A.; Babaev, Kh.F.

    1990-01-01

    A study was made of the effect of L-DOPA on the dynamics of changes in lipid peroxidation products (LPP) and the content of various types of SH-groups in certain brain structures (oblongata, cerebellum, visual and sensorimotor cortex) and their synaptosomal fractions upon irradiation. The preadministration of L-DOPA to irradiated rats inhibited LPP accumulation, prevented the decrease in the content of various types of thiols and thus exerted an antioxidant effect

  13. Aboveground dry biomass partitioning and nitrogen accumulation in early maturing soybean ‘Merlin’

    Directory of Open Access Journals (Sweden)

    Tadeusz Zając

    2017-12-01

    Full Text Available The aim of the study was to determine the biomass and nitrogen accumulation in early maturing soybean plants experiencing contrasting weather conditions. Soybean (Glycine max is a species of agricultural crop plant that is widely described in scientific publications. During 2014–2016, a field experiment with early maturing soybean ‘Merlin’ was carried out at Grodziec Śląski, Poland (49°48'01" N, 18°52'04" E. Results showed that the morphological traits of the plants, the yield of individual plants, and the soybean crop were all closely related to the climatic conditions. A high amount of precipitation stimulated seed development, resulting in a high production potential. The harvest index calculated for soybean ‘Merlin’ was high and exceeded 0.5 g g−1. The nitrogen content of the aboveground biomass increased during ontogenesis. The maximum yield of dry matter was noted at the green maturity phase, which subsequently decreased at the full maturity phase because of the loss of the leaf fraction. The variation in the effectiveness of nitrogen accumulation in seeds between 2015 and 2016 was 30%. The nitrogen harvest index values were high in each year of the experiment and exceeded 0.92 g−1. For the production of 1 ton of seeds with an adequate amount of soybean straw, plants needed, on average, 68 kg of nitrogen.

  14. Heat production in growing pigs calculated according to the RQ and CN methods

    DEFF Research Database (Denmark)

    Christensen, K; Chwalibog, André; Henckel, S

    1988-01-01

    1. Heat production, calculated according to the respiratory quotient methods, HE(RQ), and the carbon nitrogen balance method, HE(CN), was compared using the results from a total of 326 balance trials with 56 castrated male pigs fed different dietary composition and variable feed levels during...

  15. Anaerobic fermentation combined with low-temperature thermal pretreatment for phosphorus-accumulating granular sludge: Release of carbon source and phosphorus as well as hydrogen production potential.

    Science.gov (United States)

    Zou, Jinte; Li, Yongmei

    2016-10-01

    Releases of organic compounds and phosphorus from phosphorus-accumulating granular sludge (PGS) and phosphorus-accumulating flocculent sludge (PFS) during low-temperature thermal pretreatment and anaerobic fermentation were investigated. Meanwhile, biogas production potential and microbial community structures were explored. The results indicate that much more soluble chemical oxygen demand (SCOD) and phosphorus were released from PGS than from PFS via low-temperature thermal pretreatment because of the higher extracellular polymeric substances (EPS) content in PGS and higher ratio of phosphorus reserved in EPS. Furthermore, PGS contains more anaerobes and dead cells, resulting in much higher SCOD and volatile fatty acids release from PGS than those from PFS during fermentation. PGS fermentation facilitated the n-butyric acid production, and PGS exhibited the hydrogen production potential during fermentation due to the presence of hydrogen-producing bacteria. Therefore, anaerobic fermentation combined with low-temperature thermal pretreatment can facilitate the recovery of carbon and phosphorus as well as producing hydrogen from PGS. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Calculation of gas migration in fractured rock - a continuum approach

    International Nuclear Information System (INIS)

    Braester, C.

    1987-09-01

    A study of gas migration from low level radioactive repositories in which the fractured rock mass was conceptualized as a continuum, was carried out by the aid of a computer program based on a finite difference numerical method of solution to the equations of flow. The calculations are intended to correspond to the prevailing in the Forsmark low level repository area where radioactive waste repository caverns are planned to be located at a depth of about 50 metres below the sea level. Calculations were worked out for a constant gas flow rate equivalent to a gas production of 20 000 normal cubic metres per year. The investigated flow domain was a vertical cross-section passing through the repository. The results show that in the empty cavern the gas formed in the cavern moves almost instantaneously upward amd accumulates below the roof of the cavern. (orig./DG)

  17. Effect of total solids content on biohydrogen production and lactic acid accumulation during dark fermentation of organic waste biomass.

    Science.gov (United States)

    Ghimire, Anish; Trably, Eric; Frunzo, Luigi; Pirozzi, Francesco; Lens, Piet N L; Esposito, Giovanni; Cazier, Elisabeth A; Escudié, Renaud

    2018-01-01

    Production of biohydrogen and related metabolic by-products was investigated in Solid State Dark Fermentation (SSDF) of food waste (FW) and wheat straw (WS). The effect of the total solids (TS) content and H 2 partial pressure (pp H2 ), two of the main operating factors of SSDF, were investigated. Batch tests with FW at 10, 15, 20, 25 and 30% TS showed considerable effects of the TS on metabolites distribution. H 2 production was strongly inhibited for TS contents higher than 15% with a concomitant accumulation of lactic acid and a decrease in substrate conversion. Varying the pp H2 had no significant effect on the conversion products and overall degradation of FW and WS, suggesting that pp H2 was not the main limiting factor in SSDF. This study showed that the conversion of complex substrates by SSDF depends on the substrate type and is limited by the TS content. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Systematic comparison of ISOLDE-SC yields with calculated in-target production rates

    International Nuclear Information System (INIS)

    Lukic, S.; Gevaert, F.; Kelic, A.; Ricciardi, M.V.; Schmidt, K.H.; Yordanov, O.

    2006-02-01

    Recently, a series of dedicated inverse-kinematics experiments performed at GSI, Darmstadt, has brought an important progress in our understanding of proton and heavy-ion induced reactions at relativistic energies. The nuclear reaction code ABRABLA that has been developed and benchmarked against the results of these experiments has been used to calculate nuclide production cross sections at different energies and with different targets and beams. These calculations are used to estimate nuclide production rates by protons in thick targets, taking into account the energy loss and the attenuation of the proton beam in the target, as well as the low-energy fission induced by the secondary neutrons. The results are compared to the yields of isotopes of various elements obtained from different targets at CERN-ISOLDE with 600 MeV protons, and the overall extraction efficiencies are deduced. The dependence of these extraction efficiencies on the nuclide half-life is found to follow a simple pattern in many different cases. A simple function is proposed to parameterize this behavior in a way that quantifies the essential properties of the extraction efficiency for the element and the target - ion-source system in question. (orig.)

  19. FOOD II: an interactive code for calculating concentrations of radionuclides in food products

    International Nuclear Information System (INIS)

    Zach, R.

    1978-11-01

    An interactive code, FOOD II, has been written in FORTRAN IV for the PDP 10 to allow calculation of concentrations of radionuclides in food products and internal doses to man under chronic release conditions. FOOD II uses models unchanged from a previous code, FOOD, developed at Battelle, Pacific Northwest Laboratories. The new code has different input and output features than FOOD and a number of options have been added to increase flexibility. Data files have also been updated. FOOD II takes into account contamination of vegetation by air and irrigation water containing radionuclides. Contamination can occur simultaneously by air and water. Both direct deposition of radionuclides on leaves, and their uptake from soil are possible. Also, animals may be contaminated by ingestion of vegetation and drinking water containing radionuclides. At present, FOOD II provides selection of 14 food types, 13 diets and numerous radionuclides. Provisions have been made to expand all of these categories. Six additional contaminated food products can also be entered directly into the dose model. Doses may be calculated for the total body and six internal organs. Summaries of concentrations in food products and internal doses to man can be displayed at a local terminal or at an auxiliary high-speed printer. (author)

  20. Evaluation of the OSCAR-4/MCNP calculation methodology for radioisotope production in the SAFARI-1 reactor

    International Nuclear Information System (INIS)

    Karriem, Z.; Zamonsky, O.M.

    2014-01-01

    The South African Nuclear Energy Corporation SOC Ltd (Necsa) is a state owned nuclear facility which owns and operates SAFARI-1, a 20 MW material testing reactor. SAFARI-1 is a multi-purpose reactor and is used for the production of radioisotopes through in-core sample irradiation. The Radiation and Reactor Theory (RRT) Section of Necsa supports SAFARI-1 operations with nuclear engineering analyses which include core-reload design, core-follow and radiation transport analyses. The primary computer codes that are used for the analyses are the OSCAR-4 nodal diffusion core simulator and the Monte Carlo transport code MCNP. RRT has developed a calculation methodology based on OSCAR-4 and MCNP to simulate the diverse in-core irradiation conditions in SAFARI-1, for the purpose of radioisotope production. In this paper we present the OSCAR-4/MCNP calculation methodology and the software tools that were developed for rapid and reliable construction of MCNP analysis models. The paper will present the application and accuracy of the methodology for the production of yttrium-90 ( 90 Y) and will include comparisons between calculation results and experimental measurements. The paper will also present sensitivity analyses that were performed to determine the effects of control rod bank position, representation of core depletion state and sample loading configuration, on the calculated 90 Y sample activity. (author)

  1. Development of a technique of the rapid analysis for forecasting of possible radionuclides accumulation in the harvest of agricultural crops

    International Nuclear Information System (INIS)

    Yadgarov, Kh.T.; Pugachev, V.V.; Kim, A.A.

    2005-01-01

    experimental received data is received. Thus, at pollution of croplands by strontium - 90 the above described method allows with sufficient for practical purposes accuracy to determine the level of pollution of agricultural crops in various soil - climatic zones and in due time to carry out practical actions on decrease of level radionuclides contamination in production of plant cultivation. To determine the level of pollution by strontium - 90 of harvest of agriculture crops it is possible also using coefficient of transition (Ct). Coefficient of transition is the relation of the contents of radionuclide in a harvest to its contents in young plants. Strontium - 90 as long-lived radionuclide, represents the big danger for living organisms. This circumstance obliges to result in methodical instructions not only arithmetic-mean value of coefficient of transition and its error, but also a possible interval of its variation with 99 % a level of probability and at calculation of a probable level of radionuclide accumulation in a harvest, obviously, it is more preferable to apply the top limit of this interval. Thus, certainly, in many cases the valid contents of strontium - 90 in production of plants cultivation will be a little bit lower than design value, but also safety of planning of given production for the food or fodder purposes substantially will be raised. Application of the given method for short-lived radionuclides senselessly by definition, therefore we investigated another long-lived radionuclide caesium - 137. At forecasting of possible accumulation of given nuclide in a harvest and in young plants of one more coefficient - coefficient of accumulation (Ca) was applied. The coefficient of accumulation (Ca) represents the relation of the content of radionuclide in a mass unit of vegetative production to its contents in a mass unit of ground. Coefficient of accumulation in plants for various soil - climatic zones changes over a wide range depending on properties of soils

  2. Assessment of gas accumulation and retention -- Tank 241-SY-101

    International Nuclear Information System (INIS)

    Alleman, R.T.; Burke, T.M.; Reynolds, D.A.; Simpson, D.E.

    1993-03-01

    An approximate analysis has been carried out to assess and estimate the maximum quantity of gas that is likely to be accumulated within waste tank 241-SY-101, and the maximum quantity which is likely to be retained after gas release events (GRE). According to the phenomenological models used for this assessment, based on interpretation of current and recent operational data, the estimated gas generation rate in the tank is approximately 4 m 3 /day (147 ft 3 /day). About half of this gas is released as it is generated, which is (essentially) continuously. The remainder is accumulated within the slurry layer of settled solids at the bottom of the tank, and released episodically in GREs, known as ''burps,'' that are induced by unstable buoyant conditions which develop when sufficient gas accumulates in the slurry. Calculations based on gas volumes to cause neutral buoyancy in the slurry predict the following: the maximum gas accumulation (at 1 atm pressure) that can occur without triggering a GRE is in the range of 606 to 1,039 m 3 (21,400 to 36,700 ft 3 ); and the maximum gas retention immediately after a GRE is equal to the maximum accumulation minus the gas released in the GRE. GREs do not necessarily involve all of the slurry. In the largest GREs, which are assumed to involve all of the slurry, the minimum gas release (at 1 atm pressure) is calculated to be in the range of 193 to 328 m 3 (6,800 to 11,600 ft 3 ). The corresponding maximum gas retention would be 413 to 711 m 3 (14,600 to 25,100 ft 3 )

  3. Preliminary Calculation of the EROI for the Production of Gas in Russia

    Directory of Open Access Journals (Sweden)

    Roman Nogovitsyn

    2014-09-01

    Full Text Available Russia is one of the world’s largest producers of energy resources. Production of energy resources in Russia is profitable, both economically and in terms of the energy produced (as measured by EROI. At the present time, Russian oil and gas companies have a policy of energy saving, and data on energy consumption is given in annual reports. Based on these data, we can make the EROI calculation. In 2013, the EROI for the production, transportation and processing of gas for Open joint stock company (OJSC “Gazprom” was 79:1; for OJSC “NOVATEK”, 76:1; for OJSC “Yakutsk Fuel and Energy Company (YATEC”, only for production, 116:1. Currently, the situation in the oil and gas industry has come to a point when there is a need for the introduction of an energy audit.

  4. Measurement of helium production cross sections of iron for d-T neutrons by helium accumulation method

    Energy Technology Data Exchange (ETDEWEB)

    Takao, Yoshiyuki; Kanda, Yukinori; Nagae, Koji; Fujimoto, Toshihiro [Kyushu Univ., Fukuoka (Japan); Ikeda, Yujiro

    1997-03-01

    Helium production cross sections of Iron were measured by helium accumulation method for neutron energies from 13.5 to 14.9 MeV. Iron samples were irradiated with FNS, an intense d-T neutron source of JAERI. As the neutron energy varies according to the emission angle at the neutron source, the samples were set around the neutron source and were irradiated by neutrons of different energy depending on each sample position. The amount of helium produced in a sample was measured by Helium Atoms Measurement System at Kyushu University. The results of this work are in good agreement with other experimental data in the literature and also compared with the evaluated values in JENDL-3. (author)

  5. Accumulative pollution, "clean technology," and policy design

    NARCIS (Netherlands)

    Toman, M.A.; Withagen, C.A.A.M.

    2000-01-01

    This paper addresses the optimal long-term management of an accumulative but assimilable pollutant through economic incentive policies that restrict more damaging production processes and induce more benign alternatives. Using a simple general equilibrium approach, we consider the possibility that

  6. Calculated /alpha/-induced thick target neutron yields and spectra, with comparison to measured data

    International Nuclear Information System (INIS)

    Wilson, W.B.; Bozoian, M.; Perry, R.T.

    1988-01-01

    One component of the neutron source associated with the decay of actinide nuclides in many environments is due to the interaction of decay /alpha/ particles in (/alpha/,n) reactions on low Z nuclides. Measurements of (/alpha/,n) thick target neutron yields and associated neutron spectra have been made for only a few combinations of /alpha/ energy and target nuclide or mixtures of actinide and target nuclides. Calculations of thick target neutron yields and spectra with the SOURCES code require /alpha/-energy-dependent cross sections for (/alpha/,n) reactions, as well as branching fractions leading to the energetically possible levels of the product nuclides. A library of these data has been accumulated for target nuclides of Z /le/ 15 using that available from measurements and from recent GNASH code calculations. SOURCES, assuming neutrons to be emitted isotopically in the center-of-mass system, uses libraries of /alpha/ stopping cross sections, (/alpha/,n) reaction cross reactions, product nuclide level branching fractions, and actinide decay /alpha/ spectra to calculate thick target (/alpha/,n) yields and neutron spectra for homogeneous combinations of nuclides. The code also calculates the thick target yield and angle intergrated neutron spectrum produced by /alpha/-particle beams on targets of homogeneous mixtures of nuclides. Illustrative calculated results are given and comparisons are made with measured thick target yields and spectra. 50 refs., 1 fig., 2 tabs

  7. Atmospheric heavy metal deposition accumulated in rural forest soils of southern Scandinavia

    DEFF Research Database (Denmark)

    Hovmand, Mads Frederik; Kemp, Kaare; Kystol, J.

    2008-01-01

    Thirty-three years of measurements of atmospheric heavy metal (HM) deposition (bulk precipitation) in Denmark combined with European emission inventories form the basis for calculating a 50-year accumulated atmospheric input to a remote forest plantation on the island of Laesoe. Soil samples taken...... in atmospheric deposition and in soils. The accumulated atmospheric deposition is of the same magnitude as the increase of these metals in the top soil....

  8. Results of dose calculations for NET accidental and normal operation releases of tritium and activation products

    International Nuclear Information System (INIS)

    Raskob, W.; Hasemann, I.

    1992-08-01

    This report documents conditions, data and results of dose calculations for accidental and normal operation releases of tritium and activation products, performed within the NET subtask SEP2.2 ('NET-Benchmark') of the European Fusion Technology Programme. For accidental releases, the computer codes UFOTRI and COSYMA for assessing the radiological consequences, have been applied for both deterministic and probabilistic calculations. The influence on dose estimates of different release times (2 minutes / 1 hour), two release heights (10 m / 150 m), two chemical forms of tritium (HT/HTO), and two different model approaches for the deposition velocity of HTO on soil was investigated. The dose calculations for normal operation effluents were performed using the tritium model of the German regulatory guidelines, parts of the advanced dose assessment model NORMTRI still under development, and the statistical atmospheric dispersion model ISOLA. Accidental and normal operation source terms were defined as follows: 10g (3.7 10 15 Bq) for accidental tritium releases, 10 Ci/day (3.7 10 11 Bq/day) for tritium releases during normal operation and unit releases of 10 9 Bq for accidental releases of activation products and fission products. (orig./HP) [de

  9. Carbon footprint of Canadian dairy products: calculations and issues.

    Science.gov (United States)

    Vergé, X P C; Maxime, D; Dyer, J A; Desjardins, R L; Arcand, Y; Vanderzaag, A

    2013-09-01

    The Canadian dairy sector is a major industry with about 1 million cows. This industry emits about 20% of the total greenhouse gas (GHG) emissions from the main livestock sectors (beef, dairy, swine, and poultry). In 2006, the Canadian dairy herd produced about 7.7 Mt of raw milk, resulting in about 4.4 Mt of dairy products (notably 64% fluid milk and 12% cheese). An integrated cradle-to-gate model (field to processing plant) has been developed to estimate the carbon footprint (CF) of 11 Canadian dairy products. The on-farm part of the model is the Unified Livestock Industry and Crop Emissions Estimation System (ULICEES). It considers all GHG emissions associated with livestock production but, for this study, it was run for the dairy sector specifically. Off-farm GHG emissions were estimated using the Canadian Food Carbon Footprint calculator, (cafoo)(2)-milk. It considers GHG emissions from the farm gate to the exit gate of the processing plants. The CF of the raw milk has been found lower in western provinces [0.93 kg of CO2 equivalents (CO2e)/L of milk] than in eastern provinces (1.12 kg of CO2e/L of milk) because of differences in climate conditions and dairy herd management. Most of the CF estimates of dairy products ranged between 1 and 3 kg of CO2e/kg of product. Three products were, however, significantly higher: cheese (5.3 kg of CO2e/kg), butter (7.3 kg of CO2e/kg), and milk powder (10.1 kg of CO2e/kg). The CF results depend on the milk volume needed, the co-product allocation process (based on milk solids content), and the amount of energy used to manufacture each product. The GHG emissions per kilogram of protein ranged from 13 to 40 kg of CO2e. Two products had higher values: cream and sour cream, at 83 and 78 kg of CO2e/kg, respectively. Finally, the highest CF value was for butter, at about 730 kg of CO2e/kg. This extremely high value is due to the fact that the intensity indicator per kilogram of product is high and that butter is almost exclusively

  10. Comparative study of radiation damage accumulation in Cu and Fe

    International Nuclear Information System (INIS)

    Caturla, M.J.; Soneda, N.; Alonso, E.; Wirth, B.D.; Diaz de la Rubia, T.; Perlado, J.M.

    2000-01-01

    Bcc and fcc metals exhibit significant differences in behavior when exposed to neutron or heavy ion irradiation. Transmission electron microscopy (TEM) observations reveal that damage in the form of stacking fault tetrahedra (SFT) is visible in copper irradiated to very low doses, but that no damage is visible in iron irradiated to the same total dose. In order to understand and quantify this difference in behavior, we have simulated damage production and accumulation in fcc Cu and bcc Fe. We use 20 keV primary knock-on atoms (PKAs) at a homologous temperature of 0.25 of the melting point. The primary damage state was calculated using molecular dynamics (MD) with empirical, embedded-atom interatomic potentials. Damage accumulation was modeled using a kinetic Monte Carlo (kMC) algorithm to follow the evolution of all defects produced in the cascades. The diffusivities and binding energies of defects are input data for this simulation and were either extracted from experiments, the literature, or calculated using MD. MD simulations reveal that vacancy clusters are produced within the cascade core in the case of copper. In iron, most of the vacancies do not cluster during cooling of the cascade core and are available for diffusion. In addition, self-interstitial atom (SIA) clusters are produced in copper cascades but those observed in iron are smaller in number and size. The combined MD/kMC simulations reveal that the visible cluster densities obtained as a function of dose are at least one order of magnitude lower in Fe than in Cu. We compare the results with experimental measurements of cluster density and find excellent agreement between the simulations and experiments when small interstitial clusters are considered to be mobile as suggested by recent MD simulations

  11. Gelidium elegans, an edible red seaweed, and hesperidin inhibit lipid accumulation and production of reactive oxygen species and reactive nitrogen species in 3T3-L1 and RAW264.7 cells.

    Science.gov (United States)

    Jeon, Hui-Jeon; Seo, Min-Jung; Choi, Hyeon-Son; Lee, Ok-Hwan; Lee, Boo-Yong

    2014-11-01

    Gelidium elegans is an edible red alga native to the intertidal area of northeastern Asia. We investigated the effect of G. elegans extract and its main flavonoids, rutin and hesperidin, on lipid accumulation and the production of reactive oxygen species (ROS) and reactive nitrogen species (RNS) in 3T3-L1 and RAW264.7 cells. Our data show that G. elegans extract decreased lipid accumulation and ROS/RNS production in a dose-dependent manner. The extract also inhibited the mRNA expression of adipogenic transcription factors, such as peroxisome proliferator-activated receptor gamma and CCAAT/enhancer-binding protein alpha, while enhancing the protein expression of the antioxidant enzymes superoxide dismutases 1 and 2, glutathione peroxidase, and glutathione reductase compared with controls. In addition, lipopolysaccharide-induced nitric oxide production was significantly reduced in G. elegans extract-treated RAW264.7 cells. In analysis of the effects of G. elegans flavonoids on lipid accumulation and ROS/RNS production, only hesperidin showed an inhibitory effect on lipid accumulation and ROS production; rutin did not affect adipogenesis and ROS status. The antiadipogenic effect of hesperidin was evidenced by the downregulation of peroxisome proliferator-activated receptor gamma, CCAAT/enhancer-binding protein alpha, and fatty acid binding protein 4 gene expression. Collectively, our data suggest that G. elegans is a potential food source containing antiobesity and antioxidant constituents. Copyright © 2014 John Wiley & Sons, Ltd.

  12. Integrated approach to gas accumulation identification in Field M

    International Nuclear Information System (INIS)

    Malyshevskaya, K; Rukavishnikov, V; Belozerov, B; Podnebesnikh, A

    2015-01-01

    The given paper describes how the integration of different methods, such as core data, well logs, production logging, seismic data and well test analysis, was used to solve the problem of determining gas accumulation boundaries in sediment complex PK1-3 of Field M. This paper is devoted to the block with wells 2, 36, 49, 85, 127, 148 of the field, since it is characterized by high uncertainty, sc. recently drilled wells 1V, 2V and 120 have produced oil, although according to the present-day geological concept they were considered to be gas saturated in the intervals investigated with production logging. Besides, well 127 that was presumably oil saturated has produced gas. By accounting mismatching production data and the geological concept, the authors have supposed that PK1-3 gas accumulation is characterized by a more complex structure than it was supposed by the predecessors and it is represented by reservoir compartmentalization and high heterogeneity. Therefore, the main goal of the work was to revise the distribution of gas saturated reservoir within the PK1-3 sediment complex. To achieve this goal, the authors have set the following tasks: to revise the geological correlation and gas oil contact; to carry out fault interpretation by means of seismic and well test data; to determine areal facies distribution on the basis of integrated core, perform a log motifs and seismic facies analysis. Thus, the estimation of the gas saturated reservoir portion was implemented in two stages: defining the boundary of gas accumulation in depth on the basis of well logs, production data and fault interpretation; reservoir distribution determination on the basis of the seismic facies analysis within the derived gas accumulation boundary

  13. Evaluation of short-chain-length polyhydroxyalkanoate accumulation in Bacillus aryabhattai

    Directory of Open Access Journals (Sweden)

    Aneesh Balakrishna Pillai

    Full Text Available Abstract This study was focused on the polyhydroxybutyrate (PHB accumulation property of Bacillus aryabhattai isolated from environment. Twenty-four polyhydroxyalkanoate (PHA producers were screened out from sixty-two environmental bacterial isolates based on Sudan Black B colony staining. Based on their PHA accumulation property, six promising isolates were further screened out. The most productive isolate PHB10 was identified as B. aryabhattai PHB10. The polymer production maxima were 3.264 g/L, 2.181 g/L, 1.47 g/L, 1.742 g/L and 1.786 g/L in glucose, fructose, maltose, starch and glycerol respectively. The bacterial culture reached its stationary and declining phases at 18 h and 21 h respectively and indicated growth-associated PHB production. Nuclear Magnetic Resonance (NMR spectra confirmed the material as PHB. The material has thermal stability between 30 and 140 °C, melting point at 170 °C and maximum thermal degradation at 287 °C. The molecular weight and poly dispersion index of the polymer were found as 199.7 kDa and 2.67 respectively. The bacterium B. aryabhattai accumulating PHB up to 75% of cell dry mass utilizing various carbon sources is a potential candidate for large scale production of bacterial polyhydroxybutyrate.

  14. Marginal cost calculation of energy production in hydro thermoelectric systems considering the transmission system

    International Nuclear Information System (INIS)

    Pereira, M.V.F.; Gorenstin, B.G.; Alvarenga Filho, S.

    1989-01-01

    The alternatives for calculation of energy marginal cost in hydroelectric systems, considering the transmission one, was analysed, including fundamental concepts; generation/transmission systems, represented by linear power flow model; production marginal costs in hydrothermal systems and computation aspects. (C.G.C.). 11 refs, 5 figs

  15. Accumulation of methylglyoxal increases the advanced glycation end-product levels in DRG and contributes to lumbar disk herniation-induced persistent pain.

    Science.gov (United States)

    Liu, Cui-Cui; Zhang, Xin-Sheng; Ruan, Yu-Ting; Huang, Zhu-Xi; Zhang, Su-Bo; Liu, Meng; Luo, Hai-Jie; Wu, Shao-Ling; Ma, Chao

    2017-08-01

    Lumbar disk herniation (LDH) with discogenic low back pain and sciatica is a common and complicated musculoskeletal disorder. The underlying mechanisms are poorly understood, and there are no effective therapies for LDH-induced pain. In the present study, we found that the patients who suffered from LDH-induced pain had elevated plasma methylglyoxal (MG) levels. In rats, implantation of autologous nucleus pulposus (NP) to the left lumbar 5 spinal nerve root, which mimicked LDH, induced mechanical allodynia, increased MG level in plasma and dorsal root ganglion (DRG), and enhanced the excitability of small DRG neurons (DRG neurons ex vivo increased the number of action potentials evoked by depolarizing current pulses. Furthermore, inhibition of MG accumulation by aminoguanidine attenuated the enhanced excitability of small DRG neurons and the mechanical allodynia induced by NP implantation. In addition, NP implantation increased levels of advanced glycation end products (AGEs) in DRG, and intrathecal injection of MG-derived AGEs induced the mechanical allodynia and DRG neuronal hyperactivity. Intrathecal injection of MG also significantly increased the expression of AGEs in DRG. Importantly, scavenging of MG by aminoguanidine also attenuated the increase in AGEs induced by NP implantation. These results suggested that LDH-induced MG accumulation contributed to persistent pain by increasing AGE levels. Thus generation of AGEs from MG may represent a target for treatment of LDH-induced pain. NEW & NOTEWORTHY Our study demonstrates that methylglyoxal accumulation via increasing advanced glycation end-product levels in dorsal root ganglion contributes to the persistent pain induced by lumbar disk herniation, which proposed potential targets for the treatment of lumbar disk herniation-induced persistent pain. Copyright © 2017 the American Physiological Society.

  16. beta-diversity and species accumulation in antarctic coastal benthos: influence of habitat, distance and productivity on ecological connectivity.

    Directory of Open Access Journals (Sweden)

    Simon F Thrush

    Full Text Available High Antarctic coastal marine environments are comparatively pristine with strong environmental gradients, which make them important places to investigate biodiversity relationships. Defining how different environmental features contribute to shifts in beta-diversity is especially important as these shifts reflect both spatio-temporal variations in species richness and the degree of ecological separation between local and regional species pools. We used complementary techniques (species accumulation models, multivariate variance partitioning and generalized linear models to assess how the roles of productivity, bio-physical habitat heterogeneity and connectivity change with spatial scales from metres to 100's of km. Our results demonstrated that the relative importance of specific processes influencing species accumulation and beta-diversity changed with increasing spatial scale, and that patterns were never driven by only one factor. Bio-physical habitat heterogeneity had a strong influence on beta-diversity at scales 40 km. Our analysis supports the emphasis on the analysis of diversity relationships across multiple spatial scales and highlights the unequal connectivity of individual sites to the regional species pool. This has important implications for resilience to habitat loss and community homogenisation, especially for Antarctic benthic communities where rates of recovery from disturbance are slow, there is a high ratio of poor-dispersing and brooding species, and high biogenic habitat heterogeneity and spatio-temporal variability in primary production make the system vulnerable to disturbance. Consequently, large areas need to be included within marine protected areas for effective management and conservation of these special ecosystems in the face of increasing anthropogenic disturbance.

  17. beta-diversity and species accumulation in antarctic coastal benthos: influence of habitat, distance and productivity on ecological connectivity.

    Science.gov (United States)

    Thrush, Simon F; Hewitt, Judi E; Cummings, Vonda J; Norkko, Alf; Chiantore, Mariachiara

    2010-07-30

    High Antarctic coastal marine environments are comparatively pristine with strong environmental gradients, which make them important places to investigate biodiversity relationships. Defining how different environmental features contribute to shifts in beta-diversity is especially important as these shifts reflect both spatio-temporal variations in species richness and the degree of ecological separation between local and regional species pools. We used complementary techniques (species accumulation models, multivariate variance partitioning and generalized linear models) to assess how the roles of productivity, bio-physical habitat heterogeneity and connectivity change with spatial scales from metres to 100's of km. Our results demonstrated that the relative importance of specific processes influencing species accumulation and beta-diversity changed with increasing spatial scale, and that patterns were never driven by only one factor. Bio-physical habitat heterogeneity had a strong influence on beta-diversity at scales 40 km. Our analysis supports the emphasis on the analysis of diversity relationships across multiple spatial scales and highlights the unequal connectivity of individual sites to the regional species pool. This has important implications for resilience to habitat loss and community homogenisation, especially for Antarctic benthic communities where rates of recovery from disturbance are slow, there is a high ratio of poor-dispersing and brooding species, and high biogenic habitat heterogeneity and spatio-temporal variability in primary production make the system vulnerable to disturbance. Consequently, large areas need to be included within marine protected areas for effective management and conservation of these special ecosystems in the face of increasing anthropogenic disturbance.

  18. Probabilistic assessment methodology for continuous-type petroleum accumulations

    Science.gov (United States)

    Crovelli, R.A.

    2003-01-01

    The analytic resource assessment method, called ACCESS (Analytic Cell-based Continuous Energy Spreadsheet System), was developed to calculate estimates of petroleum resources for the geologic assessment model, called FORSPAN, in continuous-type petroleum accumulations. The ACCESS method is based upon mathematical equations derived from probability theory in the form of a computer spreadsheet system. ?? 2003 Elsevier B.V. All rights reserved.

  19. Accumulation pattern of total nonstructural carbohydrate in ...

    African Journals Online (AJOL)

    The pattern of total nonstructural carbohydrate (TNC) accumulation in strawberry (Fragaria ananassa Duch.) nursery runner plants, cv. eCamarosaf, was determined for three growing seasons. Plant growth and fruit production patterns were also evaluated. The experiments were carried out on plants propagated in high ...

  20. Dosimetry in intrathecal radiogold therapy. 5. Principles of gonad dose calculation

    Energy Technology Data Exchange (ETDEWEB)

    Hliscs, R; Doege, H [Medizinische Akademie, Dresden (German Democratic Republic). Nuklearmedizinische Klinik

    1980-10-01

    Basing on MIRD recommendations the absorbed dose per unit of accumulated activity in the ovaries and testes is calculated when radioactivity is accumulated in the spinal and cerebral liquor space as well as in the liver following instillation of /sup 198/Au colloid for intrathecal therapy of acute leukemia in childhood. The calculations were made for the IAEA standard man as well as for a 100 cm tall child. Besides that the maximum value of ovarian exposure for the child was determined which arises when the ovaries are close to the spinal column.

  1. Nonlocal effects on dynamic damage accumulation in brittle solids

    Energy Technology Data Exchange (ETDEWEB)

    Chen, E.P.

    1995-12-01

    This paper presents a nonlocal analysis of the dynamic damage accumulation processes in brittle solids. A nonlocal formulation of a microcrack based continuum damage model is developed and implemented into a transient dynamic finite element computer code. The code is then applied to the study of the damage accumulation process in a concrete plate with a central hole and subjected to the action of a step tensile pulse applied at opposite edges of the plate. Several finite element discretizations are used to examine the mesh size effect. Comparisons between calculated results based on local and nonlocal formulations are made and nonlocal effects are discussed.

  2. Organic carbon accumulation and reactivity in central Swedish lakes during the Holocene

    Science.gov (United States)

    Chmiel, H.; Kokic, J.; Niggemann, J.; Dittmar, T.; Sobek, S.

    2012-04-01

    Sedimentation and burial of particulate organic carbon (POC), received from terrestrial sources and from lake internal primary production, are responsible for the progressive accumulation and long-term storage of organic matter in lake basins. For lakes in the boreal zone of central Sweden it can be presumed, that the onset of POC accumulation occurred during the early Holocene (˜8000 BP.) after the retreat of the Scandinavian ice sheet. In this study we investigated carbon mass accumulation rates (CMARs), as well as sources and reactivity of deposited organic material, for seven lakes in central Sweden (60°N, 15°E), in order to obtain a detailed temporal resolution of carbon burial and preservation in boreal lakes. Sediment long-cores were sampled in March 2011 from the ice, and CMARs were calculated from water contents, dry bulk densities, carbon contents and radiocarbon (14C) ages of the depth profiles. To indicate the sources of the organic material and characterize its diagenetic state, we determined carbon-nitrogen ratios (C/N) as well as amounts and compositions of lignin phenols. The transitions from organic rich sediment layers to glacial till deposits were found to be in sediment depths of ˜3 m in each lake. POC contents were on average highest (25-34 wt. % C), in small lakes (≤ 0.07 km2) and lowest (10-18 wt. % C) in the larger lakes (≥ 165 km2). The CMARs over the Holocene showed significant variations and were on average lower in the early Holocene, compared to recent accumulation rates. C/N values and the composition of lignin phenols further provided indications of important changes in organic matter source and reactivity over the Holocene. In summary, our data suggest that boreal lake sediments were a significantly stronger sink for organic carbon during the last ~150 years than during earlier periods of the Holocene.

  3. Carbon Calculator for Land Use Change from Biofuels Production (CCLUB) Users’ Manual and Technical Documentation

    Energy Technology Data Exchange (ETDEWEB)

    Dunn, Jennifer B. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Qin, Zhangcai [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Mueller, Steffen [Univ. of Illinois, Chicago, IL (United States). Energy Resources Center; Kwon, Ho-young [International Food Policy Research Institute (IFPRI), Washington, DC (United States); Wander, Michelle M. [Univ. of Illinois at Urbana Champaign, Urbana, IL (United States). Dept. of Natural Resources; Wang, Michael [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division

    2016-09-01

    The $\\underline{C}$arbon $\\underline{C}$alculator for $\\underline{L}$and $\\underline{U}$se Change from $\\underline{B}$iofuels Production (CCLUB) calculates carbon emissions from land use change (LUC) for four different ethanol production pathways including corn grain ethanol and cellulosic ethanol from corn stover, Miscanthus, and switchgrass. This document discusses the version of CCLUB released September 30, 2014 which includes corn and three cellulosic feedstocks: corn stover, Miscanthus, and switchgrass.

  4. Calculation of scalar products of wave functions and form factors in the framework of the algebraic Bethe ansatz

    International Nuclear Information System (INIS)

    Slavnov, N.A.

    1989-01-01

    The Bethe ansatz method is widely used to investigate two-dimensional completely integrable models. In the framework of the quantum inverse scattering method it has proved to be possible to construct an algebraic scheme of the Bethe ansatz, and this has been successfully applied to calculation of correlation functions. One of the important questions of the method is that of the scalar products of the wave functions. In particular, knowledge of the properties of the scalar products is necessary for investigating the form factors and correlation function. In the present paper the author considers a generalized model with R matrix of the model of the nonlinear Schroedinger equation. The main formulas and notation are given in Sec. 2. In Sec. 3 he calculates the scalar product of an arbitrary function and an eigenfunction of the Hamiltonian. The generalized two-site model is introduced in Sec. 4. In Sec. 5 he calculates the form factor of the particle number operator

  5. Growth, biomass production and ions accumulation in Atriplex nummularia Lindl grown under abiotic stress

    Directory of Open Access Journals (Sweden)

    Hidelblandi F. de Melo

    2016-02-01

    Full Text Available ABSTRACT Atriplex nummularia is a halophyte of great importance in the recovery of saline soils and is considered as a model plant to study biosaline scenarios. This study aimed to evaluate biometric parameters, biomass production and the accumulation of ions in A. nummularia grown under abiotic stresses. Cultivation was carried out in a Fluvic Neosol for 100 days, adopting two water regimes: 37 and 70% of field capacity. Plants were irrigated with saline solutions containing two types of salts (NaCl and a mixture of NaCl, KCl, MgCl2 and CaCl2 at six levels of electrical conductivity: 0, 5, 10, 20, 30 and 40 dS m-1, arranged in a 6 x 2 x 2 factorial with 4 replicates, forming 96 plots. At the end of the experiment, plants were divided into leaves, stem and roots, for the determination of fresh matter (FM, dry matter (DM and estimated leaf area (LA, besides the contents of Ca2+, Mg2+, Na+, K+ and Cl-. The type of salt did not influence plant growth or biomass production; however, it influenced the levels of Ca2+, Mg2+, Na+ and Cl- in the leaves and Mg2+, K+ and Cl- in the roots. Increase in salinity reduced the contents of Ca2+, Mg2+, Na+, K+ and Cl- for all treatments.

  6. Far-Field Accumulation of Fissile Material From Waste Packages Containing Plutonium Disposition Waste Form

    International Nuclear Information System (INIS)

    J.P. Nicot

    2000-01-01

    The objective of this calculation is to estimate the quantity of fissile material that could accumulate in fractures in the rock beneath plutonium-ceramic (Pu-ceramic) and Mixed-Oxide (MOX) waste packages (WPs) as they degrade in the potential monitored geologic repository at Yucca Mountain. This calculation is to feed another calculation (Ref. 31) computing the probability of criticality in the systems described in Section 6 and then ultimately to a more general report on the impact of plutonium on the performance of the proposed repository (Ref. 32), both developed concurrently to this work. This calculation is done in accordance with the development plan TDP-DDC-MD-000001 (Ref. 9), item 5. The original document described in item 5 has been split into two documents: this calculation and Ref. 4. The scope of the calculation is limited to only very low flow rates because they lead to the most conservative cases for Pu accumulation and more generally are consistent with the way the effluent from the WP (called source term in this calculation) was calculated (Ref. 4). Ref. 4 (''In-Drift Accumulation of Fissile Material from WPs Containing Plutonium Disposition Waste Forms'') details the evolution through time (breach time is initial time) of the chemical composition of the solution inside the WP as degradation of the fuel and other materials proceed. It is the chemical solution used as a source term in this calculation. Ref. 4 takes that same source term and reacts it with the invert; this calculation reacts it with the rock. In addition to reactions with the rock minerals (that release Si and Ca), the basic mechanisms for actinide precipitation are dilution and mixing with resident water as explained in Section 2.1.4. No other potential mechanism such as flow through a reducing zone is investigated in this calculation. No attempt was made to use the effluent water from the bottom of the invert instead of using directly the effluent water from the WP. This

  7. The relationships between dioxin accumulation in human body and eating habits

    Energy Technology Data Exchange (ETDEWEB)

    Kajihara, H; Miura, A [Graduate School of Science and Technology, Univ. of Niigata, Niigata (Japan); Sasaki, S; Hasegawa, Y; Ando, N; Ozawa, T; Takahashi, Y [Faculty of Engineering, Univ. of Niigata, Niigata (Japan); Nakadaira, H; Yamamoto, M [Graduate School of Medical and Dental Sciences, Univ. of Niigata, Niigata (Japan); Nakamura, S; Shimada, K [Niigata Prefectural Kamo Hospital, Niigata (Japan)

    2004-09-15

    Exposure of human to dioxins was dominated by food. In Japan, the tolerable daily intake (TDI) of dioxins is set at 4 pg-TEQ/kg/day. However, important parameters, such as adsorption rate and half-life, which are used in the calculation process to determining the TDI of dioxins, were not intensively clarified. The objective of this study is to investigate the relationship between dioxin accumulation in the human body and eating habits, in order to obtain information on the accumulation behavior of dioxins ingested by humans.

  8. Comparative enzymology of the adenosine triphosphate sulfurylases from leaf tissue of selenium-accumulator and non-accumulator plants

    Energy Technology Data Exchange (ETDEWEB)

    Shaw, W H; Anderson, J W

    1974-01-01

    ATP sulfurylases were partially purified (20-40-fold) from leaf tissue of Astragalus bisulcatus, Astragalus racemosus (selenium-accumulator species) and Astragalus hamosus and Astragalus sinicus (non-accumulator species). Activity was measured by sulfate-dependent PP/sub 1/-ATP exchange. The enzymes were separated from pyrophosphatase and adenosine triphosphatase activities. The properties of the Astragalus ATP sulfurylases were similar to the spinach enzyme. The ATP sulfurylases from both selenium-accumulator and non-accumulator species catalyzed selenate-dependent PP/sub 1/-ATP exchange; selenate competed with sulfate. The ratio of V(selenate)/V(sulfate) and K/sub m/ (selenate)/K/sub m/(sulfate) was approximately the same for the enzyme from each species. Sulfate-dependent PP/sub 1/-ATP exchange was inhibited by ADP, chlorate and nitrate. The kinetics of the inhibition for each enzyme were consistent with an ordered reaction mechanisms, in which ATP is the first substrate to react with the enzyme and PP/sub 1/ is the first product released. Synthesis of adenosine 5'-(/sup 35/S)sulfatophosphate from (/sup 35/S)sulfate was demonstrated by coupling the Astrgalus ATP sulfurylases with Mg/sup 2 +/-dependent pyrophosphatase; the reaction was inhibited by selenate. An analogous reaction using (/sup 75/Se)selenate as substrate could not be demonstrated.

  9. Coupled channel calculations for electron-positron pair production in collisions of heavy ions

    CERN Document Server

    Gail, M; Scheid, W

    2003-01-01

    Coupled channel calculations are performed for electron-positron pair production in relativistic collisions of heavy ions. For this purpose the wavefunction is expanded into different types of basis sets consisting of atomic wavefunctions centred around the projectile ion only and around both of the colliding nuclei. The results are compared with experimental data from Belkacem et al (1997 Phys. Rev. A 56 2807).

  10. Calculations of individual doses for Techa River Cohort members exposed to atmospheric radioiodine from Mayak releases

    Energy Technology Data Exchange (ETDEWEB)

    Napier, Bruce A.; Eslinger, Paul W.; Tolstykh, Evgenia I.; Vorobiova, Marina I.; Tokareva, Elena E.; Akhramenko, Boris N.; Krivoschapov, Victor A.; Degteva, Marina O.

    2017-11-01

    Time-dependent thyroid doses were reconstructed for Techa River Cohort members living near the Mayak production facilities from 131I released to the atmosphere for all relevant exposure pathways. The calculational approach uses four general steps: 1) construct estimates of releases of 131I to the air from production facilities; 2) model the transport of 131I in the air and subsequent deposition on the ground and vegetation; 3) model the accumulation of 131I in soil, water, and food products (environmental media); and 4) calculate individual doses by matching appropriate lifestyle and consumption data for the individual to concentrations of 131I in environmental media. The dose calculations are implemented in a Monte Carlo framework that produces best estimates and confidence intervals of dose time-histories. The 131I contribution was 75-99% of the thyroid dose. The mean total thyroid dose for cohort members was 193 mGy and the median was 53 mGy. Thyroid doses for about 3% of cohort members were larger than 1 Gy. About 7% of children born in 1940-1950 had doses larger than 1 Gy. The uncertainty in the 131I dose estimates is low enough for this approach to be used in regional epidemiological studies.

  11. Production of medical radioisotope 153Sm in the Tehran Research Reactor (TRR) through theoretical calculations and practical tests

    International Nuclear Information System (INIS)

    Forughi, Sh.; Hamidi, S.; Khalafi, H.; Sheibani, Sh.; Shahidi, A.

    2013-01-01

    Highlights: ► Production of 153 Sm isotope by neutron activation in a nuclear reactor was studied. ► Optimal parameters for weight and irradiation time were found. ► This study led to an empirical correction factor (kf). ► Kf enhanced the production procedure of the 153 Sm radioisotope. ► The results led to nearly 60% decrease in the amount of material used in the production process. - Abstract: The feasibility of producing 2000–3000 mCi 153 Sm by irradiation of 152 Sm in 5 MW TRR was studied via TRR core simulation. In this study the cross-section of 152 Sm (n,γ) 153 Sm reaction from ENDF/B library was used. The effective activation cross section for production of 153 Sm is obtained using the neutron spectra in different irradiation channel of the core. The activity of the simulated samples is calculated using the obtained fluxes and cross sections. Then samples were prepared and irradiated under different conditions and fluxes. The final production’s specific activity was measured by the standard dose calibrator ISOMED 1010. By comparison of the theoretical calculations and actual measurements, an empirical correction factor (K f ) was obtained, which is helpful in production procedure of the 153 Sm radioisotope. The optimal weight of the samples and irradiation time was studied according to the flux calculations based on the location of the sample and saturated activity calculation. In order to test the proposed conditions, samples were prepared and were irradiated under the proposed conditions. According to the compared results with the initial irradiation condition, the new proposed sample which weighed 4 mg of Sm 2 O 3 is acceptable for the labeling, therefore this study led to nearly 60% decrease in the amount of material used in the production process

  12. Development of a deformable dosimetric phantom to verify dose accumulation algorithms for adaptive radiotherapy.

    Science.gov (United States)

    Zhong, Hualiang; Adams, Jeffrey; Glide-Hurst, Carri; Zhang, Hualin; Li, Haisen; Chetty, Indrin J

    2016-01-01

    Adaptive radiotherapy may improve treatment outcomes for lung cancer patients. Because of the lack of an effective tool for quality assurance, this therapeutic modality is not yet accepted in clinic. The purpose of this study is to develop a deformable physical phantom for validation of dose accumulation algorithms in regions with heterogeneous mass. A three-dimensional (3D) deformable phantom was developed containing a tissue-equivalent tumor and heterogeneous sponge inserts. Thermoluminescent dosimeters (TLDs) were placed at multiple locations in the phantom each time before dose measurement. Doses were measured with the phantom in both the static and deformed cases. The deformation of the phantom was actuated by a motor driven piston. 4D computed tomography images were acquired to calculate 3D doses at each phase using Pinnacle and EGSnrc/DOSXYZnrc. These images were registered using two registration software packages: VelocityAI and Elastix. With the resultant displacement vector fields (DVFs), the calculated 3D doses were accumulated using a mass-and energy congruent mapping method and compared to those measured by the TLDs at four typical locations. In the static case, TLD measurements agreed with all the algorithms by 1.8% at the center of the tumor volume and by 4.0% in the penumbra. In the deformable case, the phantom's deformation was reproduced within 1.1 mm. For the 3D dose calculated by Pinnacle, the total dose accumulated with the Elastix DVF agreed well to the TLD measurements with their differences <2.5% at four measured locations. When the VelocityAI DVF was used, their difference increased up to 11.8%. For the 3D dose calculated by EGSnrc/DOSXYZnrc, the total doses accumulated with the two DVFs were within 5.7% of the TLD measurements which are slightly over the rate of 5% for clinical acceptance. The detector-embedded deformable phantom allows radiation dose to be measured in a dynamic environment, similar to deforming lung tissues, supporting

  13. Development of a deformable dosimetric phantom to verify dose accumulation algorithms for adaptive radiotherapy

    Directory of Open Access Journals (Sweden)

    Hualiang Zhong

    2016-01-01

    Full Text Available Adaptive radiotherapy may improve treatment outcomes for lung cancer patients. Because of the lack of an effective tool for quality assurance, this therapeutic modality is not yet accepted in clinic. The purpose of this study is to develop a deformable physical phantom for validation of dose accumulation algorithms in regions with heterogeneous mass. A three-dimensional (3D deformable phantom was developed containing a tissue-equivalent tumor and heterogeneous sponge inserts. Thermoluminescent dosimeters (TLDs were placed at multiple locations in the phantom each time before dose measurement. Doses were measured with the phantom in both the static and deformed cases. The deformation of the phantom was actuated by a motor driven piston. 4D computed tomography images were acquired to calculate 3D doses at each phase using Pinnacle and EGSnrc/DOSXYZnrc. These images were registered using two registration software packages: VelocityAI and Elastix. With the resultant displacement vector fields (DVFs, the calculated 3D doses were accumulated using a mass-and energy congruent mapping method and compared to those measured by the TLDs at four typical locations. In the static case, TLD measurements agreed with all the algorithms by 1.8% at the center of the tumor volume and by 4.0% in the penumbra. In the deformable case, the phantom's deformation was reproduced within 1.1 mm. For the 3D dose calculated by Pinnacle, the total dose accumulated with the Elastix DVF agreed well to the TLD measurements with their differences <2.5% at four measured locations. When the VelocityAI DVF was used, their difference increased up to 11.8%. For the 3D dose calculated by EGSnrc/DOSXYZnrc, the total doses accumulated with the two DVFs were within 5.7% of the TLD measurements which are slightly over the rate of 5% for clinical acceptance. The detector-embedded deformable phantom allows radiation dose to be measured in a dynamic environment, similar to deforming lung

  14. Clonal variation in heavy metal accumulation and biomass production in a poplar coppice culture. II. Vertical distribution and phytoextraction potential

    International Nuclear Information System (INIS)

    Laureysens, I.; Temmerman, L. de; Hastir, T.; Gysel, M. van; Ceulemans, R.

    2005-01-01

    Short rotation coppice cultures (SRC) are intensively managed, high-density plantations of multi-shoot trees. In April 1996, an SRC field trial with 17 different poplar clones was established in Boom (Belgium) on a former waste disposal site. In December 1996 and January 2001, all shoots were cut back to a height of 5 cm to create a coppice culture. For six clones, wood and bark were sampled at the bottom, middle and top of a shoot in August and November 2002. No significant height effect of metal concentration was found, but for wood, metal concentrations generally increased toward the top of the shoot in August, and decreased toward the top of the shoot in November. Phytoextraction potential of a clone was primarily determined by metal concentration and by biomass production. Shoot size and number of shoots per stool were less important, as a high biomass production could be achieved by producing a few large shoots or many smaller shoots. Clone Fritzi Pauley accumulated 1.4 kg ha -1 of Al over two years; Wolterson and Balsam Spire showed a relatively high accumulation of Cd and Zn, i.e. averaging, respectively 47 and 57 g ha -1 for Cd and 2.4 and 2.0 kg ha -1 for Zn over two years. - Poplar shows potential for phytoextraction of Al, Cd and Zn on slightly contaminated soils

  15. Clonal variation in heavy metal accumulation and biomass production in a poplar coppice culture. II. Vertical distribution and phytoextraction potential

    Energy Technology Data Exchange (ETDEWEB)

    Laureysens, I. [University of Antwerp, Campus Drie Eiken, Department of Biology, Universiteitsplein 1, B-2610 Wilrijk (Belgium)]. E-mail: ilse.laureysens@ua.ac.be; Temmerman, L. de [Veterinary and Agrochemical Research Centre (VAR), Leuvensesteenweg 17, B-3080 Tervuren (Belgium); Hastir, T. [University of Antwerp, Campus Drie Eiken, Department of Biology, Universiteitsplein 1, B-2610 Wilrijk (Belgium); Gysel, M. van [University of Antwerp, Campus Drie Eiken, Department of Chemistry, Universiteitsplein 1, B-2610 Wilrijk (Belgium); Ceulemans, R. [University of Antwerp, Campus Drie Eiken, Department of Biology, Universiteitsplein 1, B-2610 Wilrijk (Belgium)

    2005-02-01

    Short rotation coppice cultures (SRC) are intensively managed, high-density plantations of multi-shoot trees. In April 1996, an SRC field trial with 17 different poplar clones was established in Boom (Belgium) on a former waste disposal site. In December 1996 and January 2001, all shoots were cut back to a height of 5 cm to create a coppice culture. For six clones, wood and bark were sampled at the bottom, middle and top of a shoot in August and November 2002. No significant height effect of metal concentration was found, but for wood, metal concentrations generally increased toward the top of the shoot in August, and decreased toward the top of the shoot in November. Phytoextraction potential of a clone was primarily determined by metal concentration and by biomass production. Shoot size and number of shoots per stool were less important, as a high biomass production could be achieved by producing a few large shoots or many smaller shoots. Clone Fritzi Pauley accumulated 1.4 kg ha{sup -1} of Al over two years; Wolterson and Balsam Spire showed a relatively high accumulation of Cd and Zn, i.e. averaging, respectively 47 and 57 g ha{sup -1} for Cd and 2.4 and 2.0 kg ha{sup -1} for Zn over two years. - Poplar shows potential for phytoextraction of Al, Cd and Zn on slightly contaminated soils.

  16. Lutein accumulates in subcellular membranes of brain regions in adult rhesus macaques: Relationship to DHA oxidation products.

    Directory of Open Access Journals (Sweden)

    Emily S Mohn

    Full Text Available Lutein, a carotenoid with anti-oxidant functions, preferentially accumulates in primate brain and is positively related to cognition in humans. Docosahexaenoic acid (DHA, an omega-3 polyunsaturated fatty acid (PUFA, is also beneficial for cognition, but is susceptible to oxidation. The present study characterized the membrane distribution of lutein in brain regions important for different domains of cognitive function and determined whether membrane lutein was associated with brain PUFA oxidation.Adult rhesus monkeys were fed a stock diet (~2 mg/day lutein or ~0.5 μmol/kg body weight/day (n = 9 or the stock diet plus a daily supplement of lutein (~4.5 mg/day or~1 μmol/kg body weight/day and zeaxanthin (~0.5 mg/day or 0.1 μmol/kg body weight/day for 6-12 months (n = 4. Nuclear, myelin, mitochondrial, and neuronal plasma membranes were isolated using a Ficoll density gradient from prefrontal cortex (PFC, cerebellum (CER, striatum (ST, and hippocampus (HC. Carotenoids, PUFAs, and PUFA oxidation products were measured using HPLC, GC, and LC-GC/MS, respectively.All-trans-lutein (ng/mg protein was detected in all regions and membranes and was highly variable among monkeys. Lutein/zeaxanthin supplementation significantly increased total concentrations of lutein in serum, PFC and CER, as well as lutein in mitochondrial membranes and total DHA concentrations in PFC only (P<0.05. In PFC and ST, mitochondrial lutein was inversely related to DHA oxidation products, but not those from arachidonic acid (P <0.05.This study provides novel data on subcellular lutein accumulation and its relationship to DHA oxidation in primate brain. These findings support the hypothesis that lutein may be associated with antioxidant functions in the brain.

  17. Extract from Edible Red Seaweed (Gelidium amansii) Inhibits Lipid Accumulation and ROS Production during Differentiation in 3T3-L1 Cells.

    Science.gov (United States)

    Seo, Min-Jung; Lee, Ok-Hwan; Choi, Hyeon-Son; Lee, Boo-Yong

    2012-06-01

    Gelidium (G.) amansii is a red alga widely distributed in the shallow waters around East Asian countries. We investigated the effect of G. amansii on lipid accumulation and ROS (Reactive Oxygen Species) production in 3T3-L1 cells. G. amansii extracts dose-dependently inhibited lipid formation and ROS generation in cultured cells. Our results showed that anti-adipogenic effect of G. amansii was due to the reduction in mRNA expressions of PPARγ peroxisome proliferator-activated receptor-γ and aP2 (adipocyte protein 2). G. amansii extracts significantly decreased mRNA levels of a ROS-generator, NOX4 (nicotinamide adenine dinucleotide phosphate hydrogen oxidase 4), and increased the protein levels of antioxidant enzymes including SOD1/2 (superoxide dis-mutases), Gpx (glutathione peroxidase), and GR (glutathione reductase), which can lead to the reduction of ROS in the cell. In addition, the G. amansii extract enhanced mRNA levels of adiponectin, one of the adipokines secreted from adipocytes, and GLUT4, glucose uptake protein. Taken together, our study shows that G. amansii extract inhibited lipid accumulation and ROS production by controlling adipogenic signals and ROS regulating genes.

  18. BIOBUTANOL ACCUMULATION USING ALTERNATIVE SUBSTRATES BY CULTIVATION OF Clostridium acetobutylicum STRAINS

    Directory of Open Access Journals (Sweden)

    О. О. Тigunova

    2017-10-01

    Full Text Available The aim of the research was to investigate the accumulation of biobutanol by strains Clostridium acetobutylicum using alternative substrates (Jerusalem artichoke juice, technical glycerol, crude glycerol, shredded biomass of soy, rape, wheat and switchgrass. In order to increase the accumulation of butanol in the process of cultivation, the cells of C. acetobutylicum were statically immobilized on carriers (belting strips, ferrite rings and Raschig rings by the method of adsorption immobilization. The cells were precipitated by centrifugation, the supernatant was distilled and then fermentation products were determined. Gas chromatography was used to determine the presence of solvents in the culture fluid. The biggest accumulation of butanol (2 g/dm3 was at concentration of crude glycerol 16 g/dm3 in the medium, and complete inhibition of culture development — at glycerol concentration 25 g/dm3. The accumulation of butanol by the strain C. acetobutylicum ІМВ В-7407 using fill and draw method depended on the amount of sequestered and infused medium. Immobilization of the culture using the Raschig rings allowed increasing the bioconversion to butanol twice. So it is shown the possibility to use non-traditional substrates for the production of biobutanol. The most accumulation of butanol was achieved using glycerol (11 g/dm3 as water-soluble substrate, and using switchgrass as lignocelluloses substrate (2,6 g/dm3. Immobilization of C. acetobutylicum culture cells on carriers increased the accumulation of butanol. The use of Raschig rings, as carriers for immobilization, allowed increasing the accumulation of butanol twice.

  19. Ecogeomorphology of Spartina patens-dominated tidal marshes: Soil organic matter accumulation, marsh elevation dynamics, and disturbance

    Science.gov (United States)

    Cahoon, D.R.; Ford, M.A.; Hensel, P.F.; Fagherazzi, Sergio; Marani, Marco; Blum, Linda K.

    2004-01-01

    Marsh soil development and vertical accretion in Spartina patens (Aiton) Muhl.-dominated tidal marshes is largely dependent on soil organic matter accumulation from root-rhizome production and litter deposition. Yet there are few quantitative data sets on belowground production and the relationship between soil organic matter accumulation and soil elevation dynamics for this marsh type. Spartina patens marshes are subject to numerous stressors, including sea-level rise, water level manipulations (i.e., flooding and draining) by impoundments, and prescribed burning. These stressors could influence long-term marsh sustainability by their effect on root production, soil organic matter accumulation, and soil elevation dynamics. In this review, we summarize current knowledge on the interactions among vegetative production, soil organic matter accumulation and marsh elevation dynamics, or the ecogeomorphology, of Spartina patens-dominated tidal marshes. Additional studies are needed of belowground production/decomposition and soil elevation change (measured simultaneously) to better understand the links among soil organic matter accumulation, soil elevation change, and disturbance in this marsh type. From a management perspective, we need to better understand the impacts of disturbance stressors, both lethal and sub-lethal, and the interactive effect of multiple stressors on soil elevation dynamics in order to develop better management practices to safeguard marsh sustainability as sea level rises.

  20. Chemicals to enhance microalgal growth and accumulation of high-value bioproducts

    Directory of Open Access Journals (Sweden)

    Xinheng eYu

    2015-02-01

    Full Text Available Photosynthetic microalgae have attracted significant attention as they can serve as important sources for cosmetic, food and pharmaceutical products, industrial materials and even biofuel biodiesels. However, current productivity of microalga-based processes is still very low, which has restricted their scale-up application. In addition to various efforts in strain improvement and cultivation optimization, it was proposed that the productivity of microalga-based processes can also be increased using various chemicals to trigger or enhance cell growth and accumulation of bioproducts. Herein, we summarized recent progresses in applying chemical triggers or enhancers to improve cell growth and accumulation of bioproducts in algal cultures. Based on their enhancing mechanisms, these chemicals can be classified into four categories:chemicals regulating biosynthetic pathways, chemicals inducing oxidative stress responses, phytohormones and analogues regulating multiple aspects of microalgal metabolism, and chemicals directly as metabolic precursors. Taken together, the early researches demonstrated that the use of chemical stimulants could be a very effective and economical way to improve cell growth and accumulation of high-value bioproducts in large-scale cultivation of microalgae.

  1. OPTIMIZATION OF SALARY CALCULATIONS AND EMPLOYEES’ LABOUR PRODUCTIVITY STIMULATION AT THE ENTERPRISE

    Directory of Open Access Journals (Sweden)

    Olha Odnoshevna

    2017-11-01

    Full Text Available The purposes of the paper are: the detailed analysis of salary calculations, the evaluation of the effectiveness of employees’ work, the development of optimizing mechanisms of salary calculations by increasing productivity and implementation of the methods of employees’ labour stimulation. Methodology. The study is based on an analysis of different groups of enterprises, including agricultural ones. It is analysed that for today the efficiency of labour at some enterprises drops due to low wages and the lack of employees’ motivation mechanism. Results. The study found that the process of salary calculations has a lot of problematic aspects, such as a deficient work organization, insufficient stimulation of workers, poorly composed documents, etc. To improve such a situation, it is suggested an introduction of automation in order to reduce the wasting of working time for data processing of an accounting department and to improve significantly the quality and speed of information transfer to the head of an enterprise and external users. It is offered to use a labour ball to improve employees’ motivation, which is a form of accounting for the work varying on quality and quantity that was contributed to production. According to the scoring results, a mechanism of bonuses for employees is suggested. Practical implications. We suggested entering new documents to control the number of issued orders – “Registration Book of Issued Orders”. To provide a high level of quality control of executed works, it is suggested to display data in a special primary document “Record Sheet of Performance Quality”. It is offered to use partial salary payment for unprofitable enterprises through payment in kind. Value/originality. At first, the results will allow increasing the firm’s performance quality without losing employees, and subsequently – allow increasing the profitability of the enterprise.

  2. Renewable Resources, Capital Accumulation, and Economic Growth

    Directory of Open Access Journals (Sweden)

    Wei-Bin Zhang

    2011-01-01

    Full Text Available This paper proposes a dynamic economic model with physical capital and renewable resources. Different from most of the neoclassical growth models with renewable resources which are based on microeconomic foundation and neglect physical capital accumulation, this study proposes a growth model with dynamics of renewable resources and physical capital accumulation. The model is a synthesis of the neoclassical growth theory and the traditional dynamic models of renewable resources with an alternative approach to household behavior. The model describes a dynamic interdependence among physical accumulation, resource change, and division of labor under perfect competition. Because of its refined economic structure, our study enables some interactions among economic variables which are not found in the existing literature on economic growth with renewable resources. We simulate the model to demonstrate the existence of equilibrium points and motion of the dynamic system. Our comparative dynamic analysis shows, for instance, that a rise in the propensity to consume the renewable resource increases the interest rate and reduces the national and production sector’s capital stocks, wage rate and level of the consumption good. Moreover, it initially reduces and then increases the capital stocks of the resource sector and the consumption and price of the renewable resource. The stock of the renewable resource is initially increased and then reduced. Finally, labor is redistributed from the production to the resource sector.

  3. Zinc accumulation potential and toxicity threshold determined for a metal-accumulating Populus canescens clone in a dose-response study

    Energy Technology Data Exchange (ETDEWEB)

    Langer, Ingrid [Institute of Soil Science, University of Natural Resources and Applied Life Sciences, Peter Jordan-Strasse 82, A-1190 Vienna (Austria); Krpata, Doris [Institute of Microbiology, Innsbruck University, Technikerstrasse 25, A-6020 Innsbruck (Austria); Fitz, Walter J.; Wenzel, Walter W. [Institute of Soil Science, University of Natural Resources and Applied Life Sciences, Peter Jordan-Strasse 82, A-1190 Vienna (Austria); Schweiger, Peter F., E-mail: peter.schweiger@boku.ac.a [Institute of Soil Science, University of Natural Resources and Applied Life Sciences, Peter Jordan-Strasse 82, A-1190 Vienna (Austria)

    2009-10-15

    The effect of increasing soil Zn concentrations on growth and Zn tissue concentrations of a metal-accumulating aspen clone was examined in a dose-response study. Plants were grown in a soil with a low native Zn content which was spiked with Zn salt solutions and subsequently aged. Plant growth was not affected by NH{sub 4}NO{sub 3}-extractable soil Zn concentrations up to 60 mug Zn g{sup -1} soil, but it was completely inhibited at extractable concentrations above 90 mug Zn g{sup -1} soil. From these data an effective concentration of 68.5 mug extractable Zn g{sup -1} soil was calculated at which plant growth was reduced by 50%. The obtained information on toxicity threshold concentrations, and the relation between plant Zn accumulation and extractable soil Zn concentrations may be used to assess the suitability of the investigated Populus canescens clone for various phytoremediation strategies. The potential risk of metal transfer into food webs associated with P. canescens stands on Zn-polluted sites may also be estimated. - Quantitative information about the concentration-dependent Zn accumulation of Populus canescens contributes to assess its suitability for phytoremediation.

  4. Neutronic investigation and activation calculation for CFETR HCCB blankets

    Science.gov (United States)

    Shuling, XU; Mingzhun, LEI; Sumei, LIU; Kun, LU; Kun, XU; Kun, PEI

    2017-12-01

    The neutronic calculations and activation behavior of the proposed helium cooled ceramic breeder (HCCB) blanket were predicted for the Chinese Fusion Engineering Testing Reactor (CFETR) design model using the MCNP multi-particle transport code and its associated data library. The tritium self-sufficiency behavior of the HCCB blanket was assessed, addressing several important breeding-related arrangements inside the blankets. Two candidate first wall armor materials were considered to obtain a proper tritium breeding ratio (TBR). Presentations of other neutronic characteristics, including neutron flux, neutron-induced damages in terms of the accumulated dpa and helium production were also conducted. Activation, decay heat levels and contact dose rates of the components were calculated to estimate the neutron-induced radioactivity and personnel safety. The results indicate that neutron radiation is efficiently attenuated and slowed down by components placed between the plasma and toroidal field coil. The dominant nuclides and corresponding isotopes in the structural steel were discussed. A radioactivity comparison between pure beryllium and beryllium with specific impurities was also performed. After a millennium cooling time, the decay heat of all the concerned components and materials is less than 1 × 10-4 kW, and most associated in-vessel components qualify for recycling by remote handling. The results demonstrate that acceptable hands-on recycling and operation still require a further long waiting period to allow the activated products to decay.

  5. Reproduction impact of mancozeb on rainbow trout (Oncorhynchus mykiss W. and accumulation of its carcinogen metabolite, ethylene thiourea in fish products

    Directory of Open Access Journals (Sweden)

    Milena TZANOVA

    2017-06-01

    Full Text Available Pesticides can be taken up from the water and accumulated in tissues of hydrobionts, often becoming multiplied thousands of times higher in the organism than in the surrounding water. The dithiocarbamate mancozeb is applied in plant protection as fungicide. In recent years the amount of mancozeb used in Europe significantly increased. It is carcinogen due to its metabolite - ethylene thiourea (ETU, which causes thyroid and pituitary tumors. The purpose of this study is to determinate the quantity of ethylene thiourea in products of rainbow trout (Oncorhynchus mykiss W., reared in environment containing permissible, according to the European law, amount of mancozeb. Seeking an answer to the question: is this concentration limit really safe for the reproduction of rainbow trout and can the more toxic metabolite - ETU, be accumulated in the fish eggs and fillet and afterwards make them harmful to the consumers? The study included 3 stages: feeding, analysis of ethylene thiourea in fish eggs and fillet by a new developed and validated HPLC (high performance liquid chromatography method and study of the reproductive indicators. The assays of ETU in all analyzed samples (fish and water were below the limit of quantification of the method, 0.05 mg*l-1, so fish do not accumulate the carcinogen degradation product of mancozeb and the maximum residue level of mancozeb is really safe for the humans as consumers. But these environmental conditions caused reproductive disorders. They can be partly compensated by using sperm activation medium for artificial insemination of trout eggs, but successful fertilization does not guarantee successful hatching, especially of eggs in trout farms with presence of mancozeb in water, even in allowable concentration. The presented results confirm previous investigation, that Salmonidae are very sensitive fish species, react to the lowest deviations in concentration levels of xenobiotics and are used for indicator of non

  6. Development of an integrated fission product release and transport code for spatially resolved full-core calculations of V/HTRs

    International Nuclear Information System (INIS)

    Xhonneux, Andre; Allelein, Hans-Josef

    2014-01-01

    The computer codes FRESCO-I, FRESCO-II, PANAMA and SPATRA developed at Forschungszentrum Jülich in Germany in the early 1980s are essential tools to predict the fission product release from spherical fuel elements and the TRISO fuel performance, respectively, under given normal or accidental conditions. These codes are able to calculate a conservative estimation of the source term, i.e. quantity and duration of radionuclide release. Recently, these codes have been reversed engineered, modernized (FORTRAN 95/2003) and combined to form a consistent code named STACY (Source Term Analysis Code System). STACY will later become a module of the V/HTR Code Package (HCP). In addition, further improvements have been implemented to enable more detailed calculations. For example the distinct temperature profile along the pebble radius is now taken into account and coated particle failure rates can be calculated under normal operating conditions. In addition, the absolute fission product release of an V/HTR pebble bed core can be calculated by using the newly developed burnup code Topological Nuclide Transformation (TNT) replacing the former rudimentary approach. As a new functionality, spatially resolved fission product release calculations for normal operating conditions as well as accident conditions can be performed. In case of a full-core calculation, a large number of individual pebbles which follow a random path through the reactor core can be simulated. The history of the individual pebble is recorded, too. Main input data such as spatially resolved neutron fluxes and fluid dynamics data are provided by the VSOP code. Capabilities of the FRESCO-I and SPATRA code which allow for the simulation of the redistribution of fission products within the primary circuit and the deposition of fission products on graphitic and metallic surfaces are also available in STACY. In this paper, details of the STACY model and first results for its application to the 200 MW(th) HTR

  7. Safety aspects of targets for ADTT: Activity, volatile products, residual heat release

    International Nuclear Information System (INIS)

    Gai, E.V.; Ignatyuk, A.V.; Lunev, V.P.; Shubin, Yu.N.

    1999-01-01

    Safety aspects of heavy metal liquid targets for the accelerator driven systems connected with the activity accumulation and residual energy release due to the irradiation with high energy proton beam are discussed. The results obtained for the lead-bismuth target that are under construction in IPPE now in the frame of ISTC Project No. 559 are briefly presented. The calculations and the analysis of the accumulation of the spallation reaction products, activity and energy release at various moments after the accelerator shutdown are presented. The concentrations of the reaction products, the total and partial activities, the activities of volatile products are determined. The contributions of the short-lived nuclides important for the prediction of the facility behaviour in regimes with the accelerator beam trips. The calculations and analysis of the residual energy release due to different decay type have been performed. The conclusions are as follows. The obtained results showed that long lived radioactivity accumulates mainly due to primary nuclear reactions. Secondary reactions are responsible for the production of small number of long-lived isotopes Bi-207, Po-210 and some others, being generated by radiative capture of low energy neutrons. It is possible to make a conclusion that neutrons in the energy range 20 - 800 MeV and protons with energy above 100 MeV give main contribution to the total activity generation although these parts of spectra inside the target give comparatively small contribution to the total flux. The correct consideration of short-lived nuclides contribution is the main problem in the analysis of the target behaviour in the case of short accelerator shutdowns. They make the determining contribution to the both activity and the heat release at the first moments after the accelerator shutdown, creating the intermediate links and additional channels for the long-lived nuclides accumulation chains. The strong dependence of calculated

  8. Chipping and grinding production rate calculator

    Science.gov (United States)

    Mathew. Smidt; Dana Mitchell

    2014-01-01

    The data for individual chipper and grinder production estimates were recorded with all the attributes available. If a study provided more than one production estimate and there was sufficient detail to describe each estimate, we entered multiple production estimates.

  9. The accumulation and elimination of radiocesium by naturally contaminated wood ducks

    International Nuclear Information System (INIS)

    Fendley, T.T.; Manlove, M.N.; Brisbin, I.L. Jr.

    1977-01-01

    The accumulation of radiocesium was studied in hand-reared wood ducks which were released into a South Carolina swamp habitat which had been contaminated with production reactor effluents. The uptake of radiocesium by the ducks was described as: ln pCi radiocesium/g live body weight = 0.36 + 0.18 (days). There was no effect of sex on uptake rate. The average estimated time required to attain practical equilibrium (0.90 Qsub(e)) was 17.3 days, with a range from 10.2 to 26.8 days. Ducks which were recaptured after attaining equilibrium concentrations in the field (averaging 16.6 pCi radiocesium/g live body weight) showed single-component elimination-rate curves when confined in a semi-natural pen for elimination studies. Radiocesium elimination under penned conditions was described as: ln % initial body burden = 4.60-0.13 (days). Elimination-rate and body weight showed a negative linear correlation for the penned birds although there was no effect of sex on loss-rate. Radiocesium biological half-times for the penned ducks averaged 5.6 days with a range from 3.2 to 9.3 days. Calculations based on biological half-times determined from studies with the penned birds, were successful in accurately predicting both the levels and rates of radiocesium accumulation by free-living birds in the field. (author)

  10. Far-Field Accumulation of Fissile Material From Waste Packages Containing Plutonium Disposition Waste Form

    Energy Technology Data Exchange (ETDEWEB)

    J.P. Nicot

    2000-09-29

    The objective of this calculation is to estimate the quantity of fissile material that could accumulate in fractures in the rock beneath plutonium-ceramic (Pu-ceramic) and Mixed-Oxide (MOX) waste packages (WPs) as they degrade in the potential monitored geologic repository at Yucca Mountain. This calculation is to feed another calculation (Ref. 31) computing the probability of criticality in the systems described in Section 6 and then ultimately to a more general report on the impact of plutonium on the performance of the proposed repository (Ref. 32), both developed concurrently to this work. This calculation is done in accordance with the development plan TDP-DDC-MD-000001 (Ref. 9), item 5. The original document described in item 5 has been split into two documents: this calculation and Ref. 4. The scope of the calculation is limited to only very low flow rates because they lead to the most conservative cases for Pu accumulation and more generally are consistent with the way the effluent from the WP (called source term in this calculation) was calculated (Ref. 4). Ref. 4 (''In-Drift Accumulation of Fissile Material from WPs Containing Plutonium Disposition Waste Forms'') details the evolution through time (breach time is initial time) of the chemical composition of the solution inside the WP as degradation of the fuel and other materials proceed. It is the chemical solution used as a source term in this calculation. Ref. 4 takes that same source term and reacts it with the invert; this calculation reacts it with the rock. In addition to reactions with the rock minerals (that release Si and Ca), the basic mechanisms for actinide precipitation are dilution and mixing with resident water as explained in Section 2.1.4. No other potential mechanism such as flow through a reducing zone is investigated in this calculation. No attempt was made to use the effluent water from the bottom of the invert instead of using directly the effluent water from the

  11. Fission products detection in irradiated TRIGA fuel by means of gamma spectroscopy and MCNP calculation.

    Science.gov (United States)

    Cagnazzo, M; Borio di Tigliole, A; Böck, H; Villa, M

    2018-05-01

    Aim of this work was the detection of fission products activity distribution along the axial dimension of irradiated fuel elements (FEs) at the TRIGA Mark II research reactor of the Technische Universität (TU) Wien. The activity distribution was measured by means of a customized fuel gamma scanning device, which includes a vertical lifting system to move the fuel rod along its vertical axis. For each investigated FE, a gamma spectrum measurement was performed along the vertical axis, with steps of 1 cm, in order to determine the axial distribution of the fission products. After the fuel elements underwent a relatively short cooling down period, different fission products were detected. The activity concentration was determined by calibrating the gamma detector with a standard calibration source of known activity and by MCNP6 simulations for the evaluation of self-absorption and geometric effects. Given the specific TRIGA fuel composition, a correction procedure is developed and used in this work for the measurement of the fission product Zr 95 . This measurement campaign is part of a more extended project aiming at the modelling of the TU Wien TRIGA reactor by means of different calculation codes (MCNP6, Serpent): the experimental results presented in this paper will be subsequently used for the benchmark of the models developed with the calculation codes. Copyright © 2018 Elsevier Ltd. All rights reserved.

  12. Calculating Production Rate of each Branch of a Multilateral Well Using Multi-Segment Well Model: Field Example

    Directory of Open Access Journals (Sweden)

    Mohammed S. Al-Jawad

    2017-11-01

    Full Text Available Multilateral wells require a sophisticated type of well model to be applied in reservoir simulators to represent them. The model must be able to determine the flow rate of each fluid and the pressure throughout the well. The production rate calculations are very important because they give an indication about some main issues associated with multi-lateral wells such as one branch may produce water or gas before others, no production rate from one branch, and selecting the best location of a new branch for development process easily. This paper states the way to calculate production rate of each branch of a multilateral well-using multi-segment well model. The pressure behaviour of each branch is simulated dependent on knowing its production rate. This model has divided a multi-lateral well into an arbitrary number of segments depending on the required degree of accuracy and run time of the simulator. The model implemented on a field example (multi-lateral well HF-65ML in Halfaya Oil Field/Mishrif formation. The production rate and pressure behaviour of each branch are simulated during the producing interval of the multilateral well. The conclusion is that production rate of the main branch is slightly larger than a lateral branch.

  13. CFD analysis of sludge accumulation and hydraulic performance of a waste stabilization pond.

    Science.gov (United States)

    Alvarado, Andres; Sanchez, Esteban; Durazno, Galo; Vesvikar, Mehul; Nopens, Ingmar

    2012-01-01

    Sludge management in waste stabilization ponds (WSPs) is essential for safeguarding the system performance. Sludge accumulation patterns in WSPs are strongly influenced by the pond hydrodynamics. CFD modeling was applied to study the relation between velocity profiles and sludge deposition during 10 years of operation of the Ucubamba WSP in Cuenca (Ecuador). One tracer experiment was performed and three sludge accumulation scenarios based on bathymetric surveys were simulated. A residence time distribution (RTD) analysis illustrated the decrease of residence times due to sludge deposition. Sludge accumulation rates were calculated. The influence of flow pattern on the sludge deposition was studied, enabling better planning of future pond operation and desludging.

  14. Development of a tube-type solar still equipped with heat accumulation for irrigation

    International Nuclear Information System (INIS)

    Murase, Kazuo; Yamagishi, Yusuke; Iwashita, Yusuke; Sugino, Keita

    2008-01-01

    A tube-type solar still is found to be suitable for use in desert irrigation. The effectiveness of a heat accumulator with regard to distillate productivity is experimentally and numerically verified. The heat accumulator consists of tube bundles immersed in wax in order to utilize the latent heat of wax. The dynamic response to stepwise variation of irradiative intensity verified the contribution of wax to an increase of productivity only when the phase change of wax occurred. The effective distillate productivity was found to be 294.3 g/m 2 during the cyclic stepwise change of irradiative intensity, from 200 to 600 W/m 2 and back. Velocity vectors driven by natural convection and temperature contours estimated by numerical simulation verified the effectiveness of the heat accumulator especially after peak solar intensity. The latent heat of wax effectively contributed to a 15% increase in total distillate productivity per day. The still can feasibly meet irrigation water supply demands above an irrigative threshold of 17 MJ/m 2 d

  15. Primary production calculations for sea ice from bio-optical observations in the Baltic Sea

    Directory of Open Access Journals (Sweden)

    Susann Müller

    2016-09-01

    Full Text Available Abstract Bio-optics is a powerful approach for estimating photosynthesis rates, but has seldom been applied to sea ice, where measuring photosynthesis is a challenge. We measured absorption coefficients of chromophoric dissolved organic matter (CDOM, algae, and non-algal particles along with solar radiation, albedo and transmittance at four sea-ice stations in the Gulf of Finland, Baltic Sea. This unique compilation of optical and biological data for Baltic Sea ice was used to build a radiative transfer model describing the light field and the light absorption by algae in 1-cm increments. The maximum quantum yields and photoadaptation of photosynthesis were determined from 14C-incorporation in photosynthetic-irradiance experiments using melted ice. The quantum yields were applied to the radiative transfer model estimating the rate of photosynthesis based on incident solar irradiance measured at 1-min intervals. The calculated depth-integrated mean primary production was 5 mg C m–2 d–1 for the surface layer (0–20 cm ice depth at Station 3 (fast ice and 0.5 mg C m–2 d–1 for the bottom layer (20–57 cm ice depth. Additional calculations were performed for typical sea ice in the area in March using all ice types and a typical light spectrum, resulting in depth-integrated mean primary production rates of 34 and 5.6 mg C m–2 d–1 in surface ice and bottom ice, respectively. These calculated rates were compared to rates determined from 14C incorporation experiments with melted ice incubated in situ. The rate of the calculated photosynthesis and the rates measured in situ at Station 3 were lower than those calculated by the bio-optical algorithm for typical conditions in March in the Gulf of Finland by the bio-optical algorithm. Nevertheless, our study shows the applicability of bio-optics for estimating the photosynthesis of sea-ice algae.

  16. Soil Organic Matter Accumulation and Carbon Fractions along a Moisture Gradient of Forest Soils

    Directory of Open Access Journals (Sweden)

    Ewa Błońska

    2017-11-01

    Full Text Available The aim of the study was to present effects of soil properties, especially moisture, on the quantity and quality of soil organic matter. The investigation was performed in the Czarna Rózga Reserve in Central Poland. Forty circular test areas were located in a regular grid of points (100 × 300 m. Each plot was represented by one soil profile located at the plot’s center. Sample plots were located in the area with Gleysols, Cambisols and Podzols with the water table from 0 to 100 cm. In each soil sample, particle size, total carbon and nitrogen content, acidity, base cations content and fractions of soil organic matter were determined. The organic carbon stock (SOCs was calculated based on its total content at particular genetic soil horizons. A Carbon Distribution Index (CDI was calculated from the ratio of the carbon accumulation in organic horizons and the amount of organic carbon accumulation in the mineral horizons, up to 60 cm. In the soils under study, in the temperate zone, moisture is an important factor in the accumulation of organic carbon in the soil. The highest accumulation of carbon was observed in soils of swampy variant, while the lowest was in the soils of moist variant. Large accumulation of C in the soils with water table 80–100 cm results from the thick organic horizons that are characterized by lower organic matter decomposition and higher acidity. The proportion of carbon accumulation in the organic horizons to the total accumulation in the mineral horizons expresses the distribution of carbon accumulated in the soil profile, and is a measure of quality of the organic matter accumulated. Studies have confirmed the importance of moisture content in the formation of the fractional organic matter. With greater soil moisture, the ratio of humic to fulvic acids (HA/FA decreases, which may suggest an increase in carbon mobility in soils.

  17. Calculations of fuel burn up and radionuclide inventories in the Syrian miniature neutron source reactor using the WIMSD4 and CITATION codes

    International Nuclear Information System (INIS)

    Khattab, K.

    2005-01-01

    The WIMSD4 code is used to generate the fuel group constants and the infinite multiplication factor as a function of the reactor operating time for 10, 20, and 30 k W operating power levels. The uranium burn up rate and burn up percentage, the amounts of the plutonium isotopes, the concentrations and radioactivities of the fission products and actinide radionuclides accumulated in the reactor core, and the total radioactivity of the reactor core are calculated using the WIMSD4 code as well. The CITATION code is used to calculate the changes in the effective multiplication factor of the reactor.(author)

  18. Dynamic stochastic accumulation model with application to pension savings management

    Directory of Open Access Journals (Sweden)

    Melicherčik Igor

    2010-01-01

    Full Text Available We propose a dynamic stochastic accumulation model for determining optimal decision between stock and bond investments during accumulation of pension savings. Stock prices are assumed to be driven by the geometric Brownian motion. Interest rates are modeled by means of the Cox-Ingersoll-Ross model. The optimal decision as a solution to the corresponding dynamic stochastic program is a function of the duration of saving, the level of savings and the short rate. Qualitative and quantitative properties of the optimal solution are analyzed. The model is tested on the funded pillar of the Slovak pension system. The results are calculated for various risk preferences of a saver.

  19. The Extract of Litsea japonica Reduced the Development of Diabetic Nephropathy via the Inhibition of Advanced Glycation End Products Accumulation in db/db Mice

    Directory of Open Access Journals (Sweden)

    Eunjin Sohn

    2013-01-01

    Full Text Available Increasing evidence indicates that advanced glycation end products (AGEs contribute to the pathogenesis of diabetic nephropathy. The aim of this study was to investigate the protective effect of L. japonica extract (LJE against renal damage in the db/db mouse. LJE (100 or 250 mg/kg per day was given to diabetic mice for 12 weeks. Body weight, blood glucose levels, glycated hemoglobin (HbA1c levels, and proteinuria were examined. In in vitro assay of the inhibition of AGE formation, immunohistochemical analysis of podocyte loss and AGE accumulations were performed. In 20-week-old db/db mice, severe hyperglycemia developed, and proteinuria was significantly increased. Diabetes induced markedly morphological alterations to the renal glomerular cells. AGE accumulations and podocyte loss were detected in renal glomeruli. LJE treatment significantly reduced proteinuria and AGE accumulations in diabetic mice. Moreover, the loss of nephrin, an important slit diaphragm component in the kidneys, was restored by LJE treatment. Our studies suggest that LJE might be beneficial for the treatment of diabetic nephropathy. The ability of LJE to attenuate proteinuria and podocyte dysfunction may be mediated by the inhibition of AGE accumulation in the context of diabetic nephropathy in db/db mice.

  20. Accumulation rates and sediment deposition in the northwestern Mediterranean

    Science.gov (United States)

    Zuo, Z.; Eisma, D.; Gieles, R.; Beks, J.

    As part of the EROS 2000 programme, sediment mixing and accumulation rates in the northwestern Mediterranean Sea were determined, applying the 210Pb dating method to a total of 49 cores, and the results from 29 sediment cores are presented here. On the basis of the results from the 49 sediment cores, an attempt was made to present a general picture of sediment accumulation for the area of the northwestern Mediterranean. The total deposition of sediment in the area is estimated to be of the order of 34±15 × 106 ton year-1, which is half the value reported earlier by Got and Aloisi (1990) (Continental Shelf Research, 10, 841-855) for the same region. The activity-depth profiles of 210Pb show the presence of intensive mixing in the upper layer of near-shore sediments, but little or no mixing is observed in the deep-water sediments. Based on a diffusion model, sediment mixing rates calculated from excess 210Pb gradients vary from 0·002 to 7· cm2 year-1, and the deposition rates from 0·01 to 0·60 cm year-1. A linear dependence of sedimentation rate on water depth derived from the sediment cores indicates an inverse correlation between these two. The relatively high sedimentation rates and mixing rates found near the Rhône River suggest that the contribution from the river dominates the deposition system in the northwestern Mediterranean. In the deep-water basin, however, atmospheric input and biological production are clearly more important.

  1. Calculated cross sections for production and destruction of some long-lived nuclides of importance in fusion energy applications

    International Nuclear Information System (INIS)

    Gardner, M.A.; Gardner, D.G.

    1993-01-01

    Knowledge of the production and destruction of long-lived species via neutrons, photons, and charged-particles is required in many fusion energy applications, such as reactor first-wall and blanket design, radioactive waste management, etc. Here we describe our calculational results for the production, via the (n,2n) reaction, of the following long-lived species: 150 Eu(t 1/2 = 36 y), 152 Eu(t 1/2 = 13 y), and 192m2 Ir(t 1/2 = 241 y). Some comments on calculations that we've made for destruction reactions of these species are also included

  2. Tobacco as a production platform for biofuel: overexpression of Arabidopsis DGAT and LEC2 genes increases accumulation and shifts the composition of lipids in green biomass.

    Science.gov (United States)

    Andrianov, Vyacheslav; Borisjuk, Nikolai; Pogrebnyak, Natalia; Brinker, Anita; Dixon, Joseph; Spitsin, Sergei; Flynn, John; Matyszczuk, Paulina; Andryszak, Karolina; Laurelli, Marilyn; Golovkin, Maxim; Koprowski, Hilary

    2010-04-01

    When grown for energy production instead for smoking, tobacco can generate a large amount of inexpensive biomass more efficiently than almost any other agricultural crop. Tobacco possesses potent oil biosynthesis machinery and can accumulate up to 40% of seed weight in oil. In this work, we explored two metabolic engineering approaches to enhance the oil content in tobacco green tissues for potential biofuel production. First, an Arabidopsis thaliana gene diacylglycerol acyltransferase (DGAT) coding for a key enzyme in triacylglycerol (TAG) biosynthesis, was expressed in tobacco under the control of a strong ribulose-biphosphate carboxylase small subunit promoter. This modification led to up to a 20-fold increase in TAG accumulation in tobacco leaves and translated into an overall of about a twofold increase in extracted fatty acids (FA) up to 5.8% of dry biomass in Nicotiana tabacum cv Wisconsin, and up to 6% in high-sugar tobacco variety NC-55. Modified tobacco plants also contained elevated amounts of phospholipids. This increase in lipids was accompanied by a shift in the FA composition favourable for their utilization as biodiesel. Second, we expressed in tobacco Arabidopsis gene LEAFY COTYLEDON 2 (LEC2), a master regulator of seed maturation and seed oil storage under the control of an inducible Alc promoter. Stimulation of LEC2 expression in mature tobacco plants by acetaldehyde led to the accumulation of up to 6.8% per dry weight of total extracted FA. The obtained data reveal the potential of metabolically modified plant biomass for the production of biofuel.

  3. LIPID ACCUMULATION OF CHLORELLA VULGARIS UNDER DIFFERENT PHOSPHATE CONCENTRATIONS

    Directory of Open Access Journals (Sweden)

    Magdalena Karolina Rokicka

    2017-04-01

    Full Text Available The cultivation and utilization of microalgae is now a intensively developing area of research. Some species of microalgae, under appropriate conditions, accumulate large amounts of lipids in the cells. This lipids have a suitable profile of fatty acids for biodiesel production. The culture of microalgae for lipids accumulation should be performed in certain physicochemical conditions. The aim of the study was to determine the effect of variable ortophophates concentrations in the culture medium for lipids accumulation of microalgae Chlorella vulgaris and to determine of parameters of the phosphoric shock in the medium. The study confirmed the possibility of the use of the phosphoric shock in the medium to maximize lipids accumulation by the microalgae Chlorella vulgaris. In the study, 45.23% of the oil was obtained from the biomass from the culture with phosphoric shock in the medium and 18% less of the oil was obtained from the biomass from the standard culture.

  4. Calculation of cell production from [3H]Thymidine incorporation with freshwater bacteria

    International Nuclear Information System (INIS)

    Smits, J.D.; Riemann, B.

    1988-01-01

    The conversion factor for the calculation of bacterial production from rates of [ 3 H]thymidine incorporation was examined with diluted batch cultures of freshwater bacteria. Natural bacterial assemblages were grown in aged, normal, and enriched media at 10 to 20 degree C. The generation time during 101 growth cycles covered a range from 4 to >200 h. The average conversion factor was 2.15 x 10 18 cells mol -1 of thymidine incorporated into the trichloroacetic acid (TCA) precipitate, when the generation time exceeded 20 h. At generation times of 18 cells mol -1 of thymidine incorporated into TCA precipitate. The amount of radioactivity in purified DNA increased with decreasing generation time and increasing conversion factor (calculated from the TCA precipitate), corresponding to a decrease in the percentage in protein. The conversion factors calculated from purified DNA or from the TCA precipitate gave the same variability. Conversion factors did not change significantly with the medium, but were significantly higher at 20 degree C that at 15 and 10 degree C. Results suggests that incorporation of [ 3 H]thymidine into DNA is probably limited by uptake during period with generation times of 18 cells mol -1 of thymidine incorporated is used

  5. Product-related emissions of Mercury to Air in the European Union

    Energy Technology Data Exchange (ETDEWEB)

    Kindbom, Karin; Munthe, John

    2007-06-15

    Mercury emissions to air from the use of mercury in products have been estimated for the EU for the year 2005. The consumption of mercury in the EU in 2005 was amounted to 125 tonnes in technical products. Estimates of emissions of mercury from dental amalgam were derived from information on cremations in European countries and average contents of amalgam fillings. Annual emissions of mercury to air from product use in EU27 have been estimated to be in the range 10-18 tonnes (best estimate 14 tonnes) from technical products and to 2-5 tonnes from cremation, in total 12-23 tonnes. Of the mercury consumed in technical products, 11% was calculated to be emitted to air, 31% to end up in safe storage while 58% would still be accumulated in society or disposed of in landfills. From the share still accumulated in society, as well as from the already land filled amounts, further emissions of mercury to air may occur in the longer term. Emissions from technical products are calculated based on the consumption of mercury in 2005. Emissions occurring in the same year but caused by consumption in the previous 10 years were derived using the consumption in 2005 and assuming the same patterns of distribution and emissions. The latest available estimates of total anthropogenic emissions of mercury in EU27 refer to the year 2000 and are in the order of 140-190 tonnes, probably to have declined to 2005. Based on these figures the contribution to anthropogenic mercury emissions to air in EU from product use and cremation in 2005 is at least 6-16%. In a previous report product related air emissions of 72 tonnes were estimated for Europe in the mid 1990s, corresponding to 18% of the total air emissions. A significant decrease of emissions has thus occurred which is in line with a decreasing use of mercury in technical products, more efficient collection of remaining products and better emission control. However, the calculations show that the use of mercury in products still

  6. Numerical Simulation of Shale Gas Production with Thermodynamic Calculations Incorporated

    KAUST Repository

    Urozayev, Dias

    2015-06-01

    In today’s energy sector, it has been observed a revolutionary increase in shale gas recovery induced by reservoir fracking. So-called unconventional reservoirs became profitable after introducing a well stimulation technique. Some of the analysts expect that shale gas is going to expand worldwide energy supply. However, there is still a lack of an efficient as well as accurate modeling techniques, which can provide a good recovery and production estimates. Gas transports in shale reservoir is a complex process, consisting of slippage effect, gas diffusion along the wall, viscous flow due to the pressure gradient. Conventional industrial simulators are unable to model the flow as the flow doesn’t follow Darcy’s formulation. It is significant to build a unified model considering all given mechanisms for shale reservoir production study and analyze the importance of each mechanism in varied conditions. In this work, a unified mathematical model is proposed for shale gas reservoirs. The proposed model was build based on the dual porosity continuum media model; mass conservation equations for both matrix and fracture systems were build using the dusty gas model. In the matrix, gas desorption, Knudsen diffusion and viscous flow were taken into account. The model was also developed by implementing thermodynamic calculations to correct for the gas compressibility, or to obtain accurate treatment of the multicomponent gas. Previously, the model was built on the idealization of the gas, considering every molecule identical without any interaction. Moreover, the compositional variety of shale gas requires to consider impurities in the gas due to very high variety. Peng-Robinson equation of state was used to com- pute and correct for the gas density to pressure relation by solving the cubic equation to improve the model. The results show that considering the compressibility of the gas will noticeably increase gas production under given reservoir conditions and slow down

  7. 19 CFR 351.406 - Calculation of normal value if sales are made at less than cost of production.

    Science.gov (United States)

    2010-04-01

    ... Price, Fair Value, and Normal Value § 351.406 Calculation of normal value if sales are made at less than cost of production. (a) Introduction. In determining normal value, the Secretary may disregard sales of... 19 Customs Duties 3 2010-04-01 2010-04-01 false Calculation of normal value if sales are made at...

  8. Shifts in Summertime Precipitation Accumulation Distributions over the US

    Science.gov (United States)

    Martinez-Villalobos, C.; Neelin, J. D.

    2017-12-01

    Precipitation accumulations, i.e., the amount of precipitation integrated over the course of an event, is a variable with both important physical and societal implications. Previous observational studies show that accumulation distributions have a characteristic shape, with an approximately power law decrease at first, followed by a sharp decrease at a characteristic large event cutoff scale. This cutoff scale is important as it limits the biggest accumulation events. Stochastic prototypes show that the resulting distributions, and importantly the large event cutoff scale, can be understood as a result of the interplay between moisture loss by precipitation and changes in moisture sinks/sources due to fluctuations in moisture divergence over the course of a precipitation event. The strength of this fluctuating moisture sink/source term is expected to increase under global warming, with both theory and climate model simulations predicting a concomitant increase in the large event cutoff scale. This cutoff scale increase has important consequences as it implies an approximately exponential increase for the largest accumulation events. Given its importance, in this study we characterize and track changes in the distribution of precipitation events accumulations over the contiguous US. Accumulation distributions are calculated using hourly precipitation data from 1700 stations, covering the 1974-2013 period over May-October. The resulting distributions largely follow the aforementioned shape, with individual cutoff scales depending on the local climate. An increase in the large event cutoff scale over this period is observed over several regions over the US, most notably over the eastern third of the US. In agreement with the increase in the cutoff, almost exponential increases in the highest accumulation percentiles occur over these regions, with increases in the 99.9 percentile in the Northeast of 70% for example. The relationship to changes in daily precipitation

  9. The accumulation of metals in lichens

    Directory of Open Access Journals (Sweden)

    Smaranda Mâșu

    2017-05-01

    Full Text Available The capacity to accumulate metal in the lichen communities has been used to identify the level of air pollution due road traffic. Several analyses have been conducted in the study, on tissue from lichens collected from six areas: the park of a town, various sites on the town’s freeway and on a county road segment with moderate traffic. The analyzed lichens were from the Parmelia spp. species which grow naturally on trees found in borderline lanes of motorways. Based on the degree of heavy metal accumulation such as Cd, Cr, Cu, Fe Mn, Pb, Ni and Zn in the Parmelia spp. lichens, a correlation has been made, with the road traffic. According to the metal bioaccumulation degree in lichens tissue, it has been established that the sources such as traffic from the outskirts of cities, from the perimeter of gas stations and of county roads continuously spread products which contain these elements, into the atmosphere. The fast information regarding the quality of the air in the environment allows the use of lichens as organism which can indicate environmental conditions and their modification by accumulating substances.

  10. Prediction of radionuclide accumulation in main ecosystem components of NPP cooling water reservoirs and assessment of acceptable radionuclide disposal into water reservoir

    International Nuclear Information System (INIS)

    Egorov, Yu.A.; Kazakov, S.V.

    1987-01-01

    The problems of prediction of radionuclide accumulation in ecosystem main components of NPP cooling water-reservoirs (CWR) and assessment of radionuclide acceptable disposal into water reservoir are considered. Two models are nessecary for the calculation technique: model of radionuclide migration and accumulation in CWR ecosystem components and calculation model of population dose commitment due to water consumption (at the public health approach to the normalization of the NPP radioactive effect on CWC) or calculation model of dose commitment on hydrocenosis components (at the ecological approach to the normalization). Analytical calculations and numerical calculation results in the model CWC, located in the USSR middle region, are presented

  11. An application program for fission product decay heat calculations

    International Nuclear Information System (INIS)

    Pham, Ngoc Son; Katakura, Jun-ichi

    2007-10-01

    The precise knowledge of decay heat is one of the most important factors in safety design and operation of nuclear power facilities. Furthermore, decay heat data also play an important role in design of fuel discharges, fuel storage and transport flasks, and in spent fuel management and processing. In this study, a new application program, called DHP (Decay Heat Power program), has been developed for exact decay heat summation calculations, uncertainty analysis, and for determination of the individual contribution of each fission product. The analytical methods were applied in the program without any simplification or approximation, in which all of linear and non-linear decay chains, and 12 decay modes, including ground state and meta-stable states, are automatically identified, and processed by using a decay data library and a fission yield data file, both in ENDF/B-VI format. The window interface of the program is designed with optional properties which is very easy for users to run the code. (author)

  12. CALCULATION OF INITIALS OPTIMAL PRODUCTION CAPACITIES CONSIDERING UNCERTAINTY ELEMENTS

    Directory of Open Access Journals (Sweden)

    Hilda Oquendo Ferrer

    2016-04-01

    Full Text Available In diversification, an attractive variant constitutes the projection of ethanol plants due to all the advantages that this represents and a crucial element for this to be effective is the existence of cane as a fundamental raw material for the sugar industry and therefore the derived productions. To project the initials optimal capacity of the plant, uncertainty in the raw material was considered. Mathematical models of capacity in time are obtained, choosing those that best fit, being the linear the simplest for future calculations. The initial capacity the plant should have is determined, also the time at which the first extension and the capacity of the plant should be done, which allows, considering other criteria, to make decisions about what should be the capacity of an ethanol plant in response to the current and future availability of sugar cane. It is presented a general method that can be used considering other tax sugar companies in a province or a region.

  13. Radon in houses utilizing stone magazines for heat accumulation

    International Nuclear Information System (INIS)

    Stranden, E.

    1981-01-01

    Measurements of 222 Rn and its daughters in three solar energy houses utilizing stone magazines for heat accumulation are reported. Theoretical calculations of the radon contribution from the stone magazines seem to be in good agreement with the measured values. The survey indicated that this method for heat accumulation could give a significant increase in the indoor radon concentration if the radium concentration of the stone material is high. The theoretical considerations suggest that a radium concentration of 1 pCi/g of the stone material could give an increment of the radon concentration in the indoor air of about 1 pCi/l. during the heating season in a house with air volume of 250 m 3 and a 10 5 -kg stone magazine. (author)

  14. Calculating vibrational spectra with sum of product basis functions without storing full-dimensional vectors or matrices.

    Science.gov (United States)

    Leclerc, Arnaud; Carrington, Tucker

    2014-05-07

    We propose an iterative method for computing vibrational spectra that significantly reduces the memory cost of calculations. It uses a direct product primitive basis, but does not require storing vectors with as many components as there are product basis functions. Wavefunctions are represented in a basis each of whose functions is a sum of products (SOP) and the factorizable structure of the Hamiltonian is exploited. If the factors of the SOP basis functions are properly chosen, wavefunctions are linear combinations of a small number of SOP basis functions. The SOP basis functions are generated using a shifted block power method. The factors are refined with a rank reduction algorithm to cap the number of terms in a SOP basis function. The ideas are tested on a 20-D model Hamiltonian and a realistic CH3CN (12 dimensional) potential. For the 20-D problem, to use a standard direct product iterative approach one would need to store vectors with about 10(20) components and would hence require about 8 × 10(11) GB. With the approach of this paper only 1 GB of memory is necessary. Results for CH3CN agree well with those of a previous calculation on the same potential.

  15. The relationship between lipid accumulation product, visceral adiposity index and high-sensitivity C-reactive protein in healthy adults

    Directory of Open Access Journals (Sweden)

    Yan ZHANG

    2013-03-01

    Full Text Available Objective  To investigate the correlation between lipid accumulation product (LAP, visceral adiposity index (VAI and high-sensitivity C-reactive protein (hs-CRP in adults, and explore whether to use such correlation as indications is superior to the traditional body fat index based on body mass index (BMI, waist circumference (WC, waist-hip ratio (WHR and waist-height ratio (WHtR. Methods  The present work was a cross-sectional study involving 501 healthy adults (321 males and 180 females from the community of Chongqing Municipality. Anthropometric indexes [height, weight, WC, hip circumference (HC], blood pressure (BP, fasting lipid profile and levels of fasting and post-load glucose, insulin and hs-CRP were measured, and BMI, WHR, WHtR, fasting insulin resistant homeostasis model assessment (HOMA-IR, LAP and VAI were calculated. The correlations between hs-CRP and other variables were analyzed. Results  Following the elevation of titer of the hs-CRP, LAP, VAI, BMI, WC, WHR, WHtR, BP, glucose level, HOMA-IR, insulin, triglyceride (TG, low-density lipoprotein cholesterol (LDL-C and apolipoprotein B (ApoB increased (P<0.05, while high-density lipoprotein cholesterol (HDL-C and apolipoprotein A1 (ApoA1 levels declined (P<0.0001. Pearson's correlation analysis demonstrated that hs-CRP was correlated with all variances (P<0.01 except for total cholesterol (TC (P=0.181 and LDL -C (P=0.325. According to forward stepwise multiple regression analysis with hs-CRP as the dependent variance, WC was the only variance entering the regression model. Conclusion  LAP, VAI levels are correlated with hs-CRP level but not the major determinant factors of hs-CRP. WC is stronger than other variances in the association with hs-CRP in adults, and is still an independent predictor of inflammation.

  16. The Bibenzyl Canniprene Inhibits the Production of Pro-Inflammatory Eicosanoids and Selectively Accumulates in Some Cannabis sativa Strains.

    Science.gov (United States)

    Allegrone, Gianna; Pollastro, Federica; Magagnini, Gianmaria; Taglialatela-Scafati, Orazio; Seegers, Julia; Koeberle, Andreas; Werz, Oliver; Appendino, Giovanni

    2017-03-24

    Canniprene (1), an isoprenylated bibenzyl unique to Cannabis sativa, can be vaporized and therefore potentially inhaled from marijuana. Canniprene (1) potently inhibited the production of inflammatory eicosanoids via the 5-lipoxygenase pathway (IC 50 0.4 μM) and also affected the generation of prostaglandins via the cyclooxygenase/microsomal prostaglandin E 2 synthase pathway (IC 50 10 μM), while the related spiranoid bibenzyls cannabispiranol (2) and cannabispirenone (3) were almost inactive in these bioassays. The concentration of canniprene (1) was investigated in the leaves of 160 strains of C. sativa, showing wide variations, from traces to >0.2%, but no correlation was found between its accumulation and a specific phytocannabinoid profile.

  17. Calculation of the Fission Product Release for the HTR-10 based on its Operation History

    International Nuclear Information System (INIS)

    Xhonneux, A.; Druska, C.; Struth, S.; Allelein, H.-J.

    2014-01-01

    Since the first criticality of the HTR-10 test reactor in 2000, a rather complex operation history was performed. As the HTR-10 is the only pebble bed reactor in operation today delivering experimental data for HTR simulation codes, an attempt was made to simulate the whole reactor operation up to the presence. Special emphasis was put on the fission product release behaviour as it is an important safety aspect of such a reactor. The operation history has to be simulated with respect to the neutronics, fluid mechanics and depletion to get a detailed knowledge about the time-dependent nuclide inventory. In this paper we report about such a simulation with VSOP 99/11 and our new fission product release code STACY. While STACY (Source Term Analysis Code System) so far was able to calculate the fission product release rates in case of an equilibrium core and during transients, it now can also be applied to running-in-phases. This coupling demonstrates a first step towards an HCP Prototype. Based on the published power histogram of the HTR-10 and additional information about the fuel loading and shuffling, a coupled neutronics, fluid dynamics and depletion calculation was performed. Special emphasis was put on the complex fuel-shuffling scheme within both VSOP and STACY. The simulations have shown that the HTR-10 up to now generated about 2580 MWd while reshuffling the core about 2.3 times. Within this paper, STACY results for the equilibrium core will be compared with FRESCO-II results being published by INET. Compared to these release rates, which are based on a few user defined life histories, in this new approach the fission product release rates of Ag-110m, Cs-137, Sr-90 and I-131 have been simulated for about 4000 tracer pebbles with STACY. For the calculation of the HTR-10 operation history time-dependent release rates are being presented as well. (author)

  18. Optimized inorganic carbon regime for enhanced growth and lipid accumulation in Chlorella vulgaris.

    Science.gov (United States)

    Lohman, Egan J; Gardner, Robert D; Pedersen, Todd; Peyton, Brent M; Cooksey, Keith E; Gerlach, Robin

    2015-01-01

    Large-scale algal biofuel production has been limited, among other factors, by the availability of inorganic carbon in the culture medium at concentrations higher than achievable with atmospheric CO2. Life cycle analyses have concluded that costs associated with supplying CO2 to algal cultures are significant contributors to the overall energy consumption. A two-phase optimal growth and lipid accumulation scenario is presented, which (1) enhances the growth rate and (2) the triacylglyceride (TAG) accumulation rate in the oleaginous Chlorophyte Chlorella vulgaris strain UTEX 395, by growing the organism in the presence of low concentrations of NaHCO3 (5 mM) and controlling the pH of the system with a periodic gas sparge of 5 % CO2 (v/v). Once cultures reached the desired cell densities, which can be "fine-tuned" based on initial nutrient concentrations, cultures were switched to a lipid accumulation metabolism through the addition of 50 mM NaHCO3. This two-phase approach increased the specific growth rate of C. vulgaris by 69 % compared to cultures sparged continuously with 5 % CO2 (v/v); further, biomass productivity (g L(-1) day(-1)) was increased by 27 %. Total biodiesel potential [assessed as total fatty acid methyl ester (FAME) produced] was increased from 53.3 to 61 % (FAME biomass(-1)) under the optimized conditions; biodiesel productivity (g FAME L(-1) day(-1)) was increased by 7.7 %. A bicarbonate salt screen revealed that American Chemical Society (ACS) and industrial grade NaHCO3 induced the highest TAG accumulation (% w/w), whereas Na2CO3 did not induce significant TAG accumulation. NH4HCO3 had a negative effect on cell health presumably due to ammonia toxicity. The raw, unrefined form of trona, NaHCO3∙Na2CO3 (sodium sesquicarbonate) induced TAG accumulation, albeit to a slightly lower extent than the more refined forms of sodium bicarbonate. The strategic addition of sodium bicarbonate was found to enhance growth and lipid accumulation rates in

  19. Constant strain accumulation rate between major earthquakes on the North Anatolian Fault.

    Science.gov (United States)

    Hussain, Ekbal; Wright, Tim J; Walters, Richard J; Bekaert, David P S; Lloyd, Ryan; Hooper, Andrew

    2018-04-11

    Earthquakes are caused by the release of tectonic strain accumulated between events. Recent advances in satellite geodesy mean we can now measure this interseismic strain accumulation with a high degree of accuracy. But it remains unclear how to interpret short-term geodetic observations, measured over decades, when estimating the seismic hazard of faults accumulating strain over centuries. Here, we show that strain accumulation rates calculated from geodetic measurements around a major transform fault are constant for its entire 250-year interseismic period, except in the ~10 years following an earthquake. The shear strain rate history requires a weak fault zone embedded within a strong lower crust with viscosity greater than ~10 20  Pa s. The results support the notion that short-term geodetic observations can directly contribute to long-term seismic hazard assessment and suggest that lower-crustal viscosities derived from postseismic studies are not representative of the lower crust at all spatial and temporal scales.

  20. Accumulation patterns around Dome C, East Antarctica, in the last 73 kyr

    Science.gov (United States)

    Cavitte, Marie G. P.; Parrenin, Frédéric; Ritz, Catherine; Young, Duncan A.; Van Liefferinge, Brice; Blankenship, Donald D.; Frezzotti, Massimo; Roberts, Jason L.

    2018-04-01

    We reconstruct the pattern of surface accumulation in the region around Dome C, East Antarctica, since the last glacial. We use a set of 18 isochrones spanning all observable depths of the ice column, interpreted from various ice-penetrating radar surveys and a 1-D ice flow model to invert for accumulation rates in the region. The shallowest four isochrones are then used to calculate paleoaccumulation rates between isochrone pairs using a 1-D assumption where horizontal advection is negligible in the time interval of each layer. We observe that the large-scale (100s km) surface accumulation gradient is spatially stable through the last 73 kyr, which reflects current modeled and observed precipitation gradients in the region. We also observe small-scale (10 s km) accumulation variations linked to snow redistribution at the surface, due to changes in its slope and curvature in the prevailing wind direction that remain spatially stationary since the last glacial.

  1. Time delays between core power production and external detector response from Monte Carlo calculations

    International Nuclear Information System (INIS)

    Valentine, T.E.; Mihalczo, J.T.

    1996-01-01

    One primary concern for design of safety systems for reactors is the time response of external detectors to changes in the core. This paper describes a way to estimate the time delay between the core power production and the external detector response using Monte Carlo calculations and suggests a technique to measure the time delay. The Monte Carlo code KENO-NR was used to determine the time delay between the core power production and the external detector response for a conceptual design of the Advanced Neutron Source (ANS) reactor. The Monte Carlo estimated time delay was determined to be about 10 ms for this conceptual design of the ANS reactor

  2. Calculation Of Fuel Burnup And Radionuclide Inventory In The Syrian Miniature Neutron Source Reactor Using The GETERA Code

    International Nuclear Information System (INIS)

    Khattab, K.; Dawahra, S.

    2011-01-01

    Calculations of the fuel burnup and radionuclide inventory in the Syrian Miniature Neutron Source Reactor (MNSR) after 10 years (the reactor core expected life) of the reactor operation time are presented in this paper using the GETERA code. The code is used to calculate the fuel group constants and the infinite multiplication factor versus the reactor operating time for 10, 20, and 30 kW operating power levels. The amounts of uranium burnup and plutonium produced in the reactor core, the concentrations and radionuclides of the most important fission product and actinide radionuclides accumulated in the reactor core, and the total radioactivity of the reactor core were calculated using the GETERA code as well. It is found that the GETERA code is better than the WIMSD4 code for the fuel burnup calculation in the MNSR reactor since it is newer and has a bigger library of isotopes and more accurate. (author)

  3. A one-dimensional, one-group absorption-production nodal method for neutron flux and power distributions calculations

    International Nuclear Information System (INIS)

    Ferreira, C.R.

    1984-01-01

    It is presented the absorption-production nodal method for steady and dynamical calculations in one-dimension and one group energy. It was elaborated the NOD1D computer code (in FORTRAN-IV language). Calculations of neutron flux and power distributions, burnup, effective multiplication factors and critical boron concentration were made with the NOD1D code and compared with results obtained through the CITATION code, which uses the finite difference method. The nuclear constants were produced by the LEOPARD code. (M.C.K.) [pt

  4. Method of calculation of tanks forced ventilation from the remnants of liquid products

    Directory of Open Access Journals (Sweden)

    С. О. Пузік

    2013-07-01

    Full Text Available The advantages of gasoline compared to other petroleum products in terms of feasibility of their research. Calculations of the duration of ventilation and changes in the concentration of vapors of gasoline remains in the gas space of the vertical tank with a capacity of 1000 m3 (RUS-1000. Nomogram constructed for the quantitative forecast available liquid balances petrol A-95 and the time duration ventylyaiyi RUS-1000 from the remnants of the petrol

  5. LOFT reflood as a function of accumulator initial gas volume

    International Nuclear Information System (INIS)

    Rhodes, H.F.

    1978-01-01

    The effect of the initial gas volume in the LOFT accumulators on the time to start of core reflood, after a LOCA, has been studied. The bases of the calculations are the data used and results presented in the Safety Analysis Report, Rev.1, August 1977, and the data in the RELAP and TOODEE2 program input and output listings. The results of this study show that an initial nitrogen volume of 12 cu ft, or more (at 600 psig initial pressure), would cause start of core reflood in time to prevent the cladding temperature from reaching 2200 0 F. The 12 cu ft initial volume will expand from 600 psig, initial pressure, to about 10 psig (containment pressure shortly after start of LOCA is approximately 8 psig) when all ECC liquid has been expelled from the accumulator. This pressure margin is considered too small; the ECC flowrate will be zero before the accumulator is empty

  6. Dose accumulation of multiple high dose rate prostate brachytherapy treatments in two commercially available image registration systems.

    Science.gov (United States)

    Poder, Joel; Yuen, Johnson; Howie, Andrew; Bece, Andrej; Bucci, Joseph

    2017-11-01

    The purpose of this study was to assess whether deformable image registration (DIR) is required for dose accumulation of multiple high dose rate prostate brachytherapy (HDRPBT) plans treated with the same catheter pattern on two different CT datasets. DIR was applied to 20 HDRPBT patients' planning CT images who received two treatment fractions on sequential days, on two different CT datasets, with the same implant. Quality of DIR in Velocity and MIM image registration systems was assessed by calculating the Dice Similarity Coefficient (DSC) and mean distance to agreement (MDA) for the prostate, urethra and rectum contours. Accumulated doses from each system were then calculated using the same DIR technique and dose volume histogram (DVH) parameters compared to manual addition with no DIR. The average DSC was found to be 0.83 (Velocity) and 0.84 (MIM), 0.80 (Velocity) and 0.80 (MIM), 0.80 (Velocity) and 0.81 (MIM), for the prostate, rectum and urethra contours, respectively. The average difference in calculated DVH parameters between the two systems using dose accumulation was less than 1%, and there was no statistically significant difference found between deformably accumulated doses in the two systems versus manual DVH addition with no DIR. Contour propagation using DIR in velocity and MIM was shown to be at least equivalent to inter-observer contouring variability on CT. The results also indicate that dose accumulation through manual addition of DVH parameters may be sufficient for HDRPBT treatments treated with the same catheter pattern on two different CT datasets. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

  7. Development of a nuclear spallation simulation code and calculations of primary spallation products

    International Nuclear Information System (INIS)

    Nishida, Takahiko; Nakahara, Yasuaki; Tsutsui, Tsuneo

    1986-08-01

    In order to make evaluations of computational models for the nuclear spallation reaction from a nuclear physics point of view, a simulation code NUCLEUS has been developed by modifying and combining the Monte Carlo codes NMTC/JAERI and NMTA/JAERI for calculating only the nuclear spallation reaction (intranuclear cascade + evaporation and/or fast fission) between a nucleus and a projectile without taking into consideration of internuclear transport. New several plotting routines have been provided for the rapid process of much more event data, obtained by using the ARGUS plotting system. The results obtained by our code can be directly compared with the experimental results using by thin foil experiments in which internuclear multiple collisions have little effects, and will serve to upgrade the calculational methods and the values of nuclear parameters currently used in the calculations. Some discussions are done about the preliminary computational results obtained by using NUCLEUS. The mass distribution and charge dispersion of reaction products are examined in some detail for the nuclear spallation reaction between incident protons and target nuclei, such as U, Pb and Ag, in the energy range from 0.5 GeV to 3.0 GeV. These results show that the distribution of reaction products ceases to change its form as the proton energy increases over about 2 GeV. The same tendency is seen in the energy dependence of the number of primary particles emitted from a nucleus. After spallation reactions, a variety of nuclei, especially many neutron deficient nuclides with nuclear charges nearly equal to ones of a target nucleus, are produced. Due to their short lifetime most of them will change to stable nuclides in due time. Finally, some important issues are discussed to improve the present simulation method. (author)

  8. Accumulation of intra-cellular polyphosphate in Chlorella vulgaris cells is related to indole-3-acetic acid produced by Azospirillum brasilense.

    Science.gov (United States)

    Meza, Beatriz; de-Bashan, Luz E; Hernandez, Juan-Pablo; Bashan, Yoav

    2015-06-01

    Accumulation of intra-cellular phosphate, as polyphosphate, was measured when the microalga Chlorella vulgaris was immobilized in alginate with either of two wild-type strains of the microalgae growth-promoting bacterium Azospirillum brasilense or their corresponding IAA-attenuated mutants. Wild type strains of A. brasilense induced higher amounts of intra-cellular phosphate in Chlorella than their respective mutants. Calculations comparing intra-cellular phosphate accumulation by culture or net accumulation by the cell and the amount of IAA that was produced by each of these strains revealed that higher IAA was linked to higher accumulations of intra-cellular phosphate. Application of four levels of exogenous IAA reported for A. brasilense and their IAA-attenuated mutants to cultures of C. vulgaris enhanced accumulation of intra-cellular phosphate; the higher the content of IAA per culture or per single cell, the higher was the amount of accumulated phosphate. When an IAA-attenuated mutant was complemented with exogenous IAA, accumulation of intra-cellular phosphate at the culture level was even higher than phosphate accumulation with the respective wild type strains. When calculating the net accumulation of intra-cellular phosphate in the complementation experiment, net intra-cellular phosphate induced by the IAA-attenuated mutant was completely restored and was similar to the wild strains. We propose that IAA produced by A. brasilense is linked to polyphosphate accumulation in C. vulgaris. Copyright © 2015 Institut Pasteur. Published by Elsevier Masson SAS. All rights reserved.

  9. Comparison Of Cd And Zn Accumulation In Tissues Of Different Vascular Plants: A Radiometric Study

    Directory of Open Access Journals (Sweden)

    Dürešová Zuzana

    2015-12-01

    Full Text Available The aim of the present work was to compare the accumulation and translocation of Cd and Zn in plants of tobacco (Nicotiana tabacum L., celery (Apium graveolens L., maize (Zea mays L., giant reed (Arundo donax L., and alpine pennycress (Noccaea caerulescens L. under conditions of short-term hydroponic experiments using nutrient solutions spiked with radionuclides 109Cd or 65Zn, and direct gamma-spectrometry. It was found that the time-course of metals accumulation in studied plants was not different in terms of target metal, but it was significantly different on the level of plant species. The highest values of Cd accumulation showed plants of giant reed, whereby the accumulation decreased in the order: giant reed > tobacco > alpine pennycress >> maize and celery. On the basis of concentration ratios (CR [Me]shoot / [Me]root calculation for both metals, it was found that Cd and Zn were in prevailing part accumulated in the root tissues and only partially accumulated in the shoots, where the amount of accumulated Cd and Zn increased from the oldest developed leaves to the youngest developed leaves. The CR values corresponding to these facts were calculated in the range 0.06 – 0.27 for Cd and for Zn 0.06 – 0.48. In terms of plant species, the CR values obtained for Cd decreased in the order: maize > celery > tobacco and giant reed > alpine pennycress. The similarity between studied objects – individual plant species on the basis of the obtained variables defining Cd or Zn accumulation at different conditions of the experiments as well as the relationships between obtained variables and conditions of the experiments were subjected to multivariate analysis method – cluster analysis (CA. According to the findings and this analysis, it can be expected that plants of tobacco and giant reed will dispose with similar characteristics as plants of alpine pennycress, which are classified as Zn/Cd hyperaccumulators, in terms of Cd or Zn accumulation

  10. Communication from the CRE relative to the calculation of the charges of the power production public utility for the year 2002; Communication de la CRE relative au calcul des charges du service public de la production d'electricite pour l'annee 2002

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-05-01

    After having analyzed the answers given to the public inquiry about the methods used for the calculation of the saved costs, the French commission of electricity regulation (CRE) indicates in this document the trends it has retained for the calculation of the charges of the power production public utility for 2002: cost overruns due to the obligation of purchase and to the purchase contracts anterior to the law from February 10, 2000; production cost overruns in non-interconnected areas (Corsica and overseas departments). (J.S.)

  11. In-Drift Accumulation of Fissile Material From Waste Packages Containing Plutonium Disposition Waste Forms

    International Nuclear Information System (INIS)

    H.W. Stockman; S. LeStrange

    2000-01-01

    The objective of this calculation is to provide estimates of the amount of fissile material flowing out of the waste package (source term) and the accumulation of fissile elements (U and Pu) in a crushed-tuff invert. These calculations provide input for the analysis of repository impacts of the Pu-ceramic waste forms. In particular, the source term results are used as input to the far-field accumulation calculation reported in Ref. 51, and the in-drift accumulation results are used as inputs for the criticality calculations reported in Ref. 2. The results are also summarized and interpreted in Ref. 52. The scope of this calculation is the waste package (WP) Viability Assessment (VA) design, which consists of an outer corrosion-allowance material (CAM) and an inner corrosion-resistant material (CRM). This design is used in this calculation in order to be consistent with earlier Pu-ceramic degradation calculations (Ref. 15). The impact of the new Enhanced Design Alternative-I1 (EDA-11) design on the results will be addressed in a subsequent report. The design of the invert (a leveling foundation, which creates a level surface of the drift floor and supports the WP mounting structure) is consistent with the EDA-I1 design. The invert will be composed of crushed stone and a steel support structure (Ref. 17). The scope of this calculation is also defined by the nominal degradation scenario, which involves the breach of the WP (Section 10.5.1.2, Ref. 48), followed by the influx of water. Water in the WP may, in time, gradually leach the fissile components and neutron absorbers out of the ceramic waste forms. Thus, the water in the WP may become laden with dissolved actinides (e.g., Pu and U), and may eventually overflow or leak from the WP. Once the water leaves the WP, it may encounter the invert, in which the actinides may reprecipitate. Several factors could induce reprecipitation; these factors include: the high surface area of the crushed stone, and the presence of

  12. In-Drift Accumulation of Fissile Material From Waste Packages Containing Plutonium Disposition Waste Form

    Energy Technology Data Exchange (ETDEWEB)

    H.W> Stockman; S. LeStrange

    2000-09-28

    The objective of this calculation is to provide estimates of the amount of fissile material flowing out of the waste package (source term) and the accumulation of fissile elements (U and Pu) in a crushed-tuff invert. These calculations provide input for the analysis of repository impacts of the Pu-ceramic waste forms. In particular, the source term results are used as input to the far-field accumulation calculation reported in Ref. 51, and the in-drift accumulation results are used as inputs for the criticality calculations reported in Ref. 2. The results are also summarized and interpreted in Ref. 52. The scope of this calculation is the waste package (WP) Viability Assessment (VA) design, which consists of an outer corrosion-allowance material (CAM) and an inner corrosion-resistant material (CRM). This design is used in this calculation in order to be consistent with earlier Pu-ceramic degradation calculations (Ref. 15). The impact of the new Enhanced Design Alternative-I1 (EDA-11) design on the results will be addressed in a subsequent report. The design of the invert (a leveling foundation, which creates a level surface of the drift floor and supports the WP mounting structure) is consistent with the EDA-I1 design. The invert will be composed of crushed stone and a steel support structure (Ref. 17). The scope of this calculation is also defined by the nominal degradation scenario, which involves the breach of the WP (Section 10.5.1.2, Ref. 48), followed by the influx of water. Water in the WP may, in time, gradually leach the fissile components and neutron absorbers out of the ceramic waste forms. Thus, the water in the WP may become laden with dissolved actinides (e.g., Pu and U), and may eventually overflow or leak from the WP. Once the water leaves the WP, it may encounter the invert, in which the actinides may reprecipitate. Several factors could induce reprecipitation; these factors include: the high surface area of the crushed stone, and the presence of

  13. Calculating Optimum sowing factor: A tool to evaluate sowing strategies and minimize seedling production cost

    Science.gov (United States)

    Eric van Steenis

    2013-01-01

    This paper illustrates how to use an excel spreadsheet as a decision-making tool to determine optimum sowing factor to minimize seedling production cost. Factors incorporated into the spreadsheet calculations include germination percentage, seeder accuracy, cost per seed, cavities per block, costs of handling, thinning, and transplanting labor, and more. In addition to...

  14. Ore reserve calculations of a sedimentary uranium deposit in Figueira, PR-Brazil

    International Nuclear Information System (INIS)

    Guerra, P.A.G.; Censi, A.C.; Marques, J.P.M.; Huijbregts, Ch.

    1978-01-01

    The are reserve calculations of a sedimentary uranium deposit in Figueira-PR-Brazil are presented. The evalution of reserves was based on chemical and/or radiometric analisys from boreholes. Geoestatistical methods were used to study the spacial correlation between radiometric and'in situ' uranium content and to calculate the equivalent uranium content without the need for chemical analysis. To this end, a new method was developed based on the regression between accumulated chemical and radiometric grades as determined by increasing thicknesses defined from the maximum peak of the γ-ray logs. Thus, the effect of non-focalization of the probe and of the continuous logging was eliminated. The system of evalution used was two-dimensional using classical Kriging to calculate thicknesses and accumulations determined using distinct cut-off grades. (Author) [pt

  15. Complementary action of jasmonic acid on salicylic acid in mediating fungal elicitor-induced flavonol glycoside accumulation of Ginkgo biloba cells.

    Science.gov (United States)

    Xu, Maojun; Dong, Jufang; Wang, Huizhong; Huang, Luqi

    2009-08-01

    The antagonistic action between jasmonic acid (JA) and salicylic acid (SA) in plant defence responses has been well documented. However, their relationship in secondary metabolite production is largely unknown. Here, we report that PB90, a protein elicitor from Phytophthora boehmeriae, triggers JA generation, SA accumulation and flavonol glycoside production of Ginkgo biloba cells. JA inhibitors suppress not only PB90-triggered JA generation, but also the elicitor-induced flavonol glycoside production. However, the elicitor can still enhance flavonol glycoside production even though the JA generation is totally inhibited. Over-expression of SA hydrolase gene NahG not only abolishes SA accumulation, but also suppresses the elicitor-induced flavonol glycoside production when JA signalling is inhibited. Interestingly, expression of NahG does not inhibit the elicitor-induced flavonol glycoside accumulation in the absence of JA inhibitors. Moreover, JA levels are significantly enhanced when SA accumulation is impaired in the transgenic cells. Together, the data suggest that both JA and SA are involved in PB90-induced flavonol glycoside production. Furthermore, we demonstrate that JA signalling might be enhanced to substitute for SA to mediate the elicitor-induced flavonol glycoside accumulation when SA signalling is impaired, which reveals an unusual complementary relationship between JA and SA in mediating plant secondary metabolite production.

  16. Photoproduction data for heating calculations

    International Nuclear Information System (INIS)

    Van der Marck, Steven C.; Koning, Arjan J.; Rochman, Dimitri

    2008-01-01

    For irradiations in a materials test reactor, the prediction of the amount of gamma heating in the reactor is important. Only a good predictive calculation will lead to an irradiation in which the specified temperatures are reached. The photons produced by fission product decay are often missing in spectrum calculations for a reactor, but the contribution of the photons can be computed effectively using engineering correlations for the amount of fission product decay and the ensuing photon spectrum. The prompt photons are usually calculated by a spectrum code based on the underlying nuclear data libraries. For most of the important nuclides, the nuclear data libraries contain data for the photon productions rates. However, there are still many nuclides for which the photon production data are missing, and some of these nuclides contribute to gamma heating. In this paper it is estimated what the contributions to heating are from photon production on nuclides such as 236 U, 238 Pu, 135 I, 135 Xe, 147 Pm, 148 Pm, 148m Pm, and 149 Sm. Also, simple arguments are given to judge the effect from photon production on all other (lumped) fission products, and from 28 Al decay. For all these calculations the High Flux Reactor is used as an example. (authors)

  17. Fission and corrosion products behavior in primary circuits of LMFBR's

    International Nuclear Information System (INIS)

    Feuerstein, H.; Thorley, A.W.

    1987-08-01

    Most of the 20 presented papers report items belonging to more than one session. The equipment results of primary circuits of LMFBR's relative to corrosion and fission products, release and chemistry of fuel, measurement techniques and analytical procedures of sodium sampling, difficulties with radionuclides and particles, reactor experiences with EBR-II, FFTF, BR10, BOR60, BN350, BN600, JOYO, and KNK-II, DFR, PFR, RAPSODIE, PHENIX, and SUPERPHENIX, and at least the verification of codes for calculation models of radioactive products accumulation and distribution are described. All 20 papers presented at the meeting are separately indexed in the database. (DG)

  18. Advanced accumulator for PWR

    International Nuclear Information System (INIS)

    Ichimura, Taiki; Chikahata, Hideyuki

    1997-01-01

    Advanced accumulators have been incorporated into the APWR design in order to simplify the safety system configuration and to improve reliability. The advanced accumulators refill the reactor vessel with a large discharge flow rate in a large LOCA, then switch to a small flow rate to continue safety injection for core reflooding. The functions of the conventional accumulator and the low head safety injection pump are integrated into this advanced accumulator. Injection performance tests simulating LOCA conditions and visualization tests for new designs have been carried out. This paper describes the APWR ECCS configuration, the advanced accumulator design and some of the injection performance and visualization test results. It was verified that the flow resistance of the advanced accumulator is independent of the model scale. The similarity law and performance data of the advanced accumulator for applying APWR was established. (author)

  19. Programmable calculator: alternative to minicomputer-based analyzer

    International Nuclear Information System (INIS)

    Hochel, R.C.

    1979-01-01

    Described are a number of typical field and laboratory counting systems that use standard stand-alone multichannel analyzers (MCA) interfaced to a Hewlett-Packard Company (HP 9830) programmable calculator. Such systems can offer significant advantages in cost and flexibility over a minicomputyr-based system. Because most laboratories tend to accumulate MCA's over the years, the programmable calculator also offers an easy way to upgrade the laboratory while making optimum use of existing systems. Software programs are easily tailored to fit a variety of general or specific applications. The only disadvantage of the calculator vs a computer-based system is in speed of analyses; however, for most applications this handicap is minimal. Applications discussed give a brief overview of the power and flexibility of the MCA-calculator approach to automated counting and data reduction

  20. Methane Production of Full-Scale Anaerobic Digestion Plants Calculated from Substrate’s Biomethane Potentials Compares Well with the One Measured On-Site

    Energy Technology Data Exchange (ETDEWEB)

    Holliger, Christof, E-mail: christof.holliger@epfl.ch [Laboratory for Environmental Biotechnology, School for Architecture, Civil and Environmental Engineering, Ecole Polytechnique Fédérale de Lausanne, Lausanne (Switzerland); Fruteau de Laclos, Hélène [Methaconsult, Préverenges (Switzerland); Hack, Gabrielle [Laboratory for Environmental Biotechnology, School for Architecture, Civil and Environmental Engineering, Ecole Polytechnique Fédérale de Lausanne, Lausanne (Switzerland)

    2017-06-09

    Biomethane potential (BMP) tests are used to determine the amount of methane that can be produced from organic materials in order to design different components of full-scale anaerobic digestion (AD) plants such as size of the digesters and units exploiting the produced biogas. However, little is known on how well BMPs compare with biogas production from the same organic materials in full-scale installations. In this study, two AD plants were chosen to carry out such comparisons, a dry AD plant treating green waste from urban areas and food waste from restaurants and supermarkets, and a liquid AD plant treating waste sludge from wastewater treatment and seven additional organic wastes. The BMPs of multiple samples of the individual organic materials collected during a period of 7–9 months were determined. Separate tests of mixtures of organic materials confirmed that the BMP of the mixtures can be calculated by adding the BMPs of the individual materials. The weekly methane production during the investigated periods was calculated from the full-scale installation data on the feeding of the digesters and the BMPs of each substrate fed into the digesters and compared with the weekly methane production measured on-site. The latter was calculated from the most accurately measured entity, either the electricity or the volume of purified biomethane injected into the grid. The weekly methane production rates calculated from BMPs and the one measured on-site were very similar and followed the same pattern. Some exceptions could be explained by, e.g., an overload of the full-scale installation. The measured weekly methane production accounted for 94.0 ± 6.8 and 89.3 ± 5.7% of the calculated weekly methane production for the wet and dry AD plant, respectively. For 26 out of 29 weeks, the calculated weekly methane production overestimated the measured one in the case of the wet AD plant and for 37 out of 39 weeks for the dry AD plant. Based on these results, it is

  1. Methane Production of Full-Scale Anaerobic Digestion Plants Calculated from Substrate’s Biomethane Potentials Compares Well with the One Measured On-Site

    International Nuclear Information System (INIS)

    Holliger, Christof; Fruteau de Laclos, Hélène; Hack, Gabrielle

    2017-01-01

    Biomethane potential (BMP) tests are used to determine the amount of methane that can be produced from organic materials in order to design different components of full-scale anaerobic digestion (AD) plants such as size of the digesters and units exploiting the produced biogas. However, little is known on how well BMPs compare with biogas production from the same organic materials in full-scale installations. In this study, two AD plants were chosen to carry out such comparisons, a dry AD plant treating green waste from urban areas and food waste from restaurants and supermarkets, and a liquid AD plant treating waste sludge from wastewater treatment and seven additional organic wastes. The BMPs of multiple samples of the individual organic materials collected during a period of 7–9 months were determined. Separate tests of mixtures of organic materials confirmed that the BMP of the mixtures can be calculated by adding the BMPs of the individual materials. The weekly methane production during the investigated periods was calculated from the full-scale installation data on the feeding of the digesters and the BMPs of each substrate fed into the digesters and compared with the weekly methane production measured on-site. The latter was calculated from the most accurately measured entity, either the electricity or the volume of purified biomethane injected into the grid. The weekly methane production rates calculated from BMPs and the one measured on-site were very similar and followed the same pattern. Some exceptions could be explained by, e.g., an overload of the full-scale installation. The measured weekly methane production accounted for 94.0 ± 6.8 and 89.3 ± 5.7% of the calculated weekly methane production for the wet and dry AD plant, respectively. For 26 out of 29 weeks, the calculated weekly methane production overestimated the measured one in the case of the wet AD plant and for 37 out of 39 weeks for the dry AD plant. Based on these results, it is

  2. Uncertainties in fission-product decay-heat calculations

    Energy Technology Data Exchange (ETDEWEB)

    Oyamatsu, K.; Ohta, H.; Miyazono, T.; Tasaka, K. [Nagoya Univ. (Japan)

    1997-03-01

    The present precision of the aggregate decay heat calculations is studied quantitatively for 50 fissioning systems. In this evaluation, nuclear data and their uncertainty data are taken from ENDF/B-VI nuclear data library and those which are not available in this library are supplemented by a theoretical consideration. An approximate method is proposed to simplify the evaluation of the uncertainties in the aggregate decay heat calculations so that we can point out easily nuclei which cause large uncertainties in the calculated decay heat values. In this paper, we attempt to clarify the justification of the approximation which was not very clear at the early stage of the study. We find that the aggregate decay heat uncertainties for minor actinides such as Am and Cm isotopes are 3-5 times as large as those for {sup 235}U and {sup 239}Pu. The recommended values by Atomic Energy Society of Japan (AESJ) were given for 3 major fissioning systems, {sup 235}U(t), {sup 239}Pu(t) and {sup 238}U(f). The present results are consistent with the AESJ values for these systems although the two evaluations used different nuclear data libraries and approximations. Therefore, the present results can also be considered to supplement the uncertainty values for the remaining 17 fissioning systems in JNDC2, which were not treated in the AESJ evaluation. Furthermore, we attempt to list nuclear data which cause large uncertainties in decay heat calculations for the future revision of decay and yield data libraries. (author)

  3. Calculations of fuel burn-up and radionuclide inventory in the syrian miniature neutron source reactor using the WIMSD4 code

    International Nuclear Information System (INIS)

    Khattab, K.

    2005-01-01

    Calculations of the fuel burn up and radionuclide inventory in the Miniature Neutron Source Reactor after 10 years (the reactor core expected life) of the reactor operating time are presented in this paper. The WIMSD4 code is used to generate the fuel group constants and the infinite multiplication factor versus the reactor operating time for 10, 20, and 30 kW operating power levels. The amounts of uranium burnt up and plutonium produced in the reactor core, the concentrations and radioactivities of the most important fission product and actinide radionuclides accumulated in the reactor core, and the total radioactivity of the reactor core are calculated using the WIMSD4 code as well

  4. Quantitative analysis of glycerol accumulation, glycolysis and growth under hyper osmotic stress.

    Directory of Open Access Journals (Sweden)

    Elzbieta Petelenz-Kurdziel

    Full Text Available We provide an integrated dynamic view on a eukaryotic osmolyte system, linking signaling with regulation of gene expression, metabolic control and growth. Adaptation to osmotic changes enables cells to adjust cellular activity and turgor pressure to an altered environment. The yeast Saccharomyces cerevisiae adapts to hyperosmotic stress by activating the HOG signaling cascade, which controls glycerol accumulation. The Hog1 kinase stimulates transcription of genes encoding enzymes required for glycerol production (Gpd1, Gpp2 and glycerol import (Stl1 and activates a regulatory enzyme in glycolysis (Pfk26/27. In addition, glycerol outflow is prevented by closure of the Fps1 glycerol facilitator. In order to better understand the contributions to glycerol accumulation of these different mechanisms and how redox and energy metabolism as well as biomass production are maintained under such conditions we collected an extensive dataset. Over a period of 180 min after hyperosmotic shock we monitored in wild type and different mutant cells the concentrations of key metabolites and proteins relevant for osmoadaptation. The dataset was used to parameterize an ODE model that reproduces the generated data very well. A detailed computational analysis using time-dependent response coefficients showed that Pfk26/27 contributes to rerouting glycolytic flux towards lower glycolysis. The transient growth arrest following hyperosmotic shock further adds to redirecting almost all glycolytic flux from biomass towards glycerol production. Osmoadaptation is robust to loss of individual adaptation pathways because of the existence and upregulation of alternative routes of glycerol accumulation. For instance, the Stl1 glycerol importer contributes to glycerol accumulation in a mutant with diminished glycerol production capacity. In addition, our observations suggest a role for trehalose accumulation in osmoadaptation and that Hog1 probably directly contributes to the

  5. Unrecorded capital flows and accumulation of foreign assets: the case of Croatia

    Directory of Open Access Journals (Sweden)

    Goran Vukšić

    2010-03-01

    Full Text Available This paper evaluates the magnitude of unrecorded capital flows and the resulting unrecorded accumulation of foreign assets for Croatia, over the period between 2000 and 2007. The problem of unrecorded capital outflows, often labeled as capital flight, has gained significance in the present global financial and economic crises, because of increasing capital scarcity in many emerging markets and transition economies including Croatia. The findings reveal relatively large amounts of unrecorded foreign asset accumulation over the observed period. A large portion of this accumulation relates to cumulative amounts of net errors and omissions term, which is interpreted as unrecorded capital flow. There are reasons to believe that this net errors and omissions item in Croatia possibly partly represents the unrecorded accumulation of foreign cash from foreign tourist spending, and/or partly results from overstated tourism income in the official statistics.However, even after excluding this item from the calculation of capital flight, the remaining unrecorded accumulation of foreign assets over the period is still substantial. Consequently, if these unrecorded flows are taken into account, Croatia’s net international investment position is improved.

  6. Calculation Methods of Topographic Factors Modification Using Data Digital Elevation Model (DEM To Predict Erosion

    Directory of Open Access Journals (Sweden)

    Hengki Simanjuntak

    2018-03-01

    Full Text Available Erosion  is a crucial information for sustainable management of land resources within a particular watershed. The information of erosion is needed for land resource management planning, and is generally counted by USLE (Universal Soil Loss Equation. One of the parameters in USLE is topographic factor (LS. The determinations of LS in erosion estimation model are vary, both in terms of LS factor equation, as well as in terms of the length of the slope (λ and slope (s measurements. There are at least 3 methods used to calculate slope factors in spatial operation, i.e (1 Input of the LS Value from Table (INT, (2 Flow accumulation, and (3 Cell Size. The study was designed to obtain a method of calculation that gives the smallest topographic factor and in order to obtain a LS factors that similar to the slope information. Research location in Kampa Sub watershed, The LS determination in Kampa Sub watershed basically are with (INT and without calculating λ and s. INT method is determination without calculating λ and s, LS value is generate from the contour map and DEM SRTM by giving LS value from table reference of LS value. The Flow Accumulation and Cell Size are determination of LS Value by calculating λ and s. The Flow Accumulation method modifies the determination of λ and s using the middle value of s, λ per land use, and λ and s per cell. Cell Size method determines λ using the amount of cell size. The results showed that the “cell size” and "INT" methods were the best method for topographic factor (LS calculation, because LS value of “cell size” and "INT" methods are smaller than the flow accumulation method and the LS value similar to the slope information. LS value from that methods generated weighted value in average of 0,55−0,58. Keywords: cell size, flow accumulation, flow direction, the length of the slope, USLE

  7. Lipid accumulation product is related to metabolic syndrome in women with polycystic ovary syndrome.

    Science.gov (United States)

    Xiang, S; Hua, F; Chen, L; Tang, Y; Jiang, X; Liu, Z

    2013-02-01

    Metabolic disturbances are common features of polycystic ovary syndrome (PCOS), which possibly enhance the risk of diabetes and cardiovascular disease. Lipid accumulation product (LAP) is an emerging cardiovascular risk factor. The aim of this study was to explore the ability of LAP to identify metabolic syndrome (MS) in PCOS women. In a cross-sectional study, anthropometric, biochemical and clinical parameters were measured in 105 PCOS women. Receiver operating characteristic (ROC) analysis was used to find out the cut-off points of LAP to predict MS. MS was categorized according to International Diabetes Federation (IDF) criteria. The prevalence of MS was 43.8% in this study. PCOS women with MS had significantly higher LAP levels compared to those without MS. LAP was highly correlated with components of MS. ROC analysis showed that LAP was a significant discriminator for MS in PCOS women, and the optimal cutoff point of LAP to predict MS was 54.2 (93.3% sensitivity, 96.7% specificity). LAP seems to be associated with MS and has a strong and reliable diagnostic accuracy for MS in PCOS women. © J. A. Barth Verlag in Georg Thieme Verlag KG Stuttgart · New York.

  8. Milk production and composition, and progeny performance in young ewes with high merit for rapid growth and muscle and fat accumulation.

    Science.gov (United States)

    Rosales Nieto, C A; Ferguson, M B; Macleay, C A; Briegel, J R; Wood, D A; Martin, G B; Bencini, R; Thompson, A N

    2018-02-26

    In ewe lambs, acceleration of growth and accumulation of both muscle and fat leads to earlier sexual maturity and better reproductive performance. The next stage in the development of this theme is to test whether these aspects of growth in young ewes affect milk production in their first lactation and the growth of their first progeny. We studied 75 young Merino ewes that had known phenotypic values for depth of eye muscle (EMD) and fat (FAT), and known Australian Sheep Breeding Values for post-weaning weight (PWT) and depths of eye muscle (PEMD) and fat (PFAT). They lambed for the first time at 1 year of age. Their lambs were weighed weekly from birth to weaning at 10 weeks to determine live weight gain and weaning weight. Progeny birth weight was positively associated with live weight gain and weaning weight (P0.05). The PWT of the sire was positively associated with live weight gain (P0.05). The concentrations of fat, protein, lactose and total solids in the milk were not affected by the phenotype or genotype of the mothers or of the sires of the mothers, or by the sex of the progeny (P>0.05). We conclude that selection of young Merino ewes for better growth, and more rapid accumulation of muscle and fat, will lead to progeny that are heavier at birth, grow faster and are heavier at weaning. Moreover, milk production and composition do not seem to be affected by the genetic merit of the mother for post-weaning live weight or PEMD or PFAT. Therefore, Merino ewes can lamb at 1 year of age without affecting the production objectives of the Merino sheep industry.

  9. Accumulation, elimination and retention of 99Tc by duckweed

    International Nuclear Information System (INIS)

    Hattink, J.; Weltje, L.; Wolterbeek, H.Th.; Goeij, J.J.M. de

    2004-01-01

    Accumulation dynamics of the long-lived fission product technetium ( 99 Tc) in duckweed is studied. Duckweed serves as model for aquatic plants, because of its representative foliar uptake for 99 Tc. 99 Tc is irreversibly accumulated and distributed over cytoplasm, chloroplasts and mitochondria. Autoradiography showed that 99 Tc was not transported to new biomass. Irreversible storage of 99 Tc in plant biomass means that steady-state situations cannot be interpreted as a balance between uptake and elimination of 99 Tc, but that 99 Tc continuously builds up in each single duckweed plant and overall Tc concentrations are averaged over new biomass. (author)

  10. Heavy metals in intensive greenhouse vegetable production systems along Yellow Sea of China

    DEFF Research Database (Denmark)

    Hu, Wenyou; Huang, Biao; Tian, Kang

    2017-01-01

    Recently, greenhouse vegetable production (GVP) has grown rapidly and counts a large proportion of vegetable production in China. In this study, the accumulation, health risk and threshold values of selected heavy metals were evaluated systematically. A total of 120 paired soil and vegetable...... relatively high concentrations and transfer factors of heavy metals. The accumulation of heavy metals in soils was affected by soil pH and soil organic matter. The calculated hazard quotients (HQ) of the heavy metals by vegetable consumption decreased in the order of leafy > rootstalk > fruit vegetables...... with hazard index (HI) values of 0.61, 0.33 and 0.26, respectively. The HI values were all below 1, which indicates that there is a low risk of greenhouse vegetable consumption. Soil threshold values (STVs) of heavy metals in GVP system were established according to the health risk assessment. The relatively...

  11. Measurement, calculation and evaluation of photon production data. Final report of a coordinated research project

    International Nuclear Information System (INIS)

    Oblozinsky, P.; Dietrich, F.S.; Mengoni, A.

    1999-12-01

    The report summarizes results of the Coordinated Research Project (CRP) devoted to photon preduction in neutron-induced reactions. The report presents 25 original contributions that reflect accomplishments achieved in measurement, calculation and evaluation of photon production under the project in 1994-1997. Major results are highlighted and a list of the CRP publications is given. (author)

  12. The Improvement of the Methodological Approaches to Calculating the Payback Period for Investment in order to Estimate Expenses on Establishing the Economic Security Service of an Enterprise

    Directory of Open Access Journals (Sweden)

    Melikhova Tetiana O.

    2018-03-01

    Full Text Available The aim of the article is to improve the methodological approaches to calculating the payback period for investment in order to determine the payback period for expenses on establishing the economic security service of an enterprise. It is found that the source of payback of investment at the enterprise level is cash flow product. These revenues (the result go to formation of a cash flow (expenses used to finance investment and financial activities. There proposed methods for determining the gross, net, actual, and specified payback periods for advanced investments in the long-term, which use the accumulated product of cash flow or accumulated cash flow as a source of financing. Analytic relationships between the gross, net, current, and specified payback periods for advanced investments that take into account the relationship between the accumulated gross, net, current and specified cash flows are proposed. The considered options for payback of advanced investment at the enterprise level will provide an opportunity to develop methods for determining the payback period for expenses on establishing the economic security service of an enterprise.

  13. Biomass Accumulation and Net Primary Production during the Early Stage of Secondary Succession after a Severe Forest Disturbance in Northern Japan

    Directory of Open Access Journals (Sweden)

    Tomotsugu Yazaki

    2016-11-01

    Full Text Available Quantitative evaluations of biomass accumulation after disturbances in forests are crucially important for elucidating and predicting forest carbon dynamics in order to understand the carbon sink/source activities. During early secondary succession, understory vegetation often affects sapling growth. However, reports on biomass recovery in naturally-regenerating sites are limited in Japan. Therefore, we traced annual or biennial changes in plant species, biomass, and net primary production (NPP in a naturally regenerating site in Japan after windthrow and salvage-logging plantation for nine years. The catastrophic disturbance depleted the aboveground biomass (AGB from 90.6 to 2.7 Mg·ha−1, changing understory dominant species from Dryopteris spp. to Rubus idaeus. The mean understory AGB recovered to 4.7 Mg·ha−1 in seven years with the dominant species changing to invasive Solidago gigantea. Subsequently, patches of deciduous trees (mainly Betula spp. recovered whereas the understory AGB decreased. Mean understory NPP increased to 272 g·C·m−2·year−1 within seven years after the disturbance, but decreased thereafter to 189 g·C·m−2·year−1. Total NPP stagnated despite increasing overstory NPP. The biomass accumulation is similar to that of naturally regenerating sites without increase of trees in boreal and temperate regions. Dense ground vegetation and low water and nutrient availability of the soil in the study site restrict the recovery of canopy-forming trees and eventually influence the biomass accumulation.

  14. SU-F-J-99: Dose Accumulation and Evaluation in Lung SBRT Among All Phases of Respiration

    Energy Technology Data Exchange (ETDEWEB)

    Azcona, JD; Barbes, B; Aristu, J; Moreno, M; Zubiria, A [Clinica Universidad de Navarra, Pamplona (Spain); Burguete, J [Universidad de Navarra, Pamplona, Navarra (Spain); Arce, P; Lagares, JI [Centro de Investigaciones Energeticas, Medioambientales, y Tecnologicas, Madrid (Spain)

    2016-06-15

    Purpose: To calculate the total planning dose on lung tumors (GTV) by accumulating the dose received in all respiration phases. Methods: A patient 4D planning CT (phase-binned, from a Siemens Somatom CT) was used to locate the GTV of a lung tumor in all respiratory phases with Pinnacle (v9.10). GTV contours defined in all phases were projected to the reference phase, where the ITV was defined. Centroids were calculated for all the GTV projections. No deformation or rotation was taken into account. The only GTV contour as defined in the reference phase was voxelized to track each voxel individually. We accumulated the absorbed dose in different phases on each voxel. A 3DCRT and a VMAT plan were designed on the reference phase fulfilling the ITV dosimetric requirements, using the 10MV FFF photon model from an Elekta Versa linac. ITV-to-PTV margins were set to 5mm. In-house developed MATLAB code was used for tumor voxeling and dose accumulation, assuming that the dose distribution planned in the reference phase behaved as a “dose-cloud” during patient breathing. Results: We tested the method on a patient 4DCT set of images exhibiting limited tumor motion (<5mm). For the 3DCRT plan, D95 was calculated for the GTV with motion and for the ITV, showing an agreement of 0.04%. For the VMAT plan, we calculated the D95 for every phase as if the GTV in that phase had received the whole treatment. Differences in D95 for all phases are within 1%, and estimate the potential interplay effect during delivery. Conclusion: A method for dose accumulation and assessment was developed that can compare GTV motion with ITV dosage, and estimate the potential interplay effect for VMAT plans. Work in progress includes the incorporation of deformable image registration and 4D CBCT dose calculation for dose reconstruction and assessment during treatment.

  15. Radionuclides accumulation in milk and its products

    International Nuclear Information System (INIS)

    Marmuleva, N.I.; Barinov, E.Y.; Petukhov, V.L.

    2003-01-01

    The problem of radioactive pollution is extremely urgent in Russia in connection with presence of territories polluted by radionuclides on places of nuclear tests, in zones around the enterprises on production, processing and storage of radioactive materials, and also in areas of emergency pollution (Barakhtin, 2001). The aim of our investigation was a determination of the levels of the main radioactive elements - 137 Cs and 90 Sr in diary products. 363 samples of milk, dry milk, butter, cheese and yogurt from Novosibirsk region were examined. 137 Cs level was 3.7 to 9.2 times higher than 90 Sr one in milk, cheese and yogurt. At the same time the level of these radio-nuclides in butter was identical (8.03 Bk/kg). (authors)

  16. EQ6 Calculations for Chemical Degradation of Navy Waste Packages

    International Nuclear Information System (INIS)

    S. LeStrange

    1999-01-01

    The Monitored Geologic Repository Waste Package Operations of the Civilian Radioactive Waste Management System Management and Operating Contractor (CRWMS M and O) performed calculations to provide input for disposal of spent nuclear fuel (SNF) from the Navy (Refs. 1 and 2). The Navy SNF has been considered for disposal at the potential Yucca Mountain site. For some waste packages, the containment may breach (Ref. 3), allowing the influx of water. Water in the waste package may moderate neutrons, increasing the likelihood of a criticality event within the waste package. The water may gradually leach the fissile components and neutron absorbers out of the waste package. In addition, the accumulation of silica (SiO 2 ) in the waste package over time may further affect the neutronics of the system. This study presents calculations of the long-term geochemical behavior of waste packages containing the Enhanced Design Alternative (EDA) II inner shell, Navy canister, and basket components. The calculations do not include the Navy SNF in the waste package. The specific study objectives were to determine the chemical composition of the water and the quantity of silicon (Si) and other solid corrosion products in the waste package during the first million years after the waste package is breached. The results of this calculation will be used to ensure that the type and amount of criticality control material used in the waste package design will prevent criticality

  17. EQ6 Calculations for Chemical Degradation of Navy Waste Packages

    Energy Technology Data Exchange (ETDEWEB)

    S. LeStrange

    1999-11-15

    The Monitored Geologic Repository Waste Package Operations of the Civilian Radioactive Waste Management System Management & Operating Contractor (CRWMS M&O) performed calculations to provide input for disposal of spent nuclear fuel (SNF) from the Navy (Refs. 1 and 2). The Navy SNF has been considered for disposal at the potential Yucca Mountain site. For some waste packages, the containment may breach (Ref. 3), allowing the influx of water. Water in the waste package may moderate neutrons, increasing the likelihood of a criticality event within the waste package. The water may gradually leach the fissile components and neutron absorbers out of the waste package. In addition, the accumulation of silica (SiO{sub 2}) in the waste package over time may further affect the neutronics of the system. This study presents calculations of the long-term geochemical behavior of waste packages containing the Enhanced Design Alternative (EDA) II inner shell, Navy canister, and basket components. The calculations do not include the Navy SNF in the waste package. The specific study objectives were to determine the chemical composition of the water and the quantity of silicon (Si) and other solid corrosion products in the waste package during the first million years after the waste package is breached. The results of this calculation will be used to ensure that the type and amount of criticality control material used in the waste package design will prevent criticality.

  18. Effect of transpiration on plant accumulation and translocation of PPCP/EDCs

    International Nuclear Information System (INIS)

    Dodgen, Laurel K.; Ueda, Aiko; Wu, Xiaoqin; Parker, David R.; Gan, Jay

    2015-01-01

    The reuse of treated wastewater for agricultural irrigation in arid and hot climates where plant transpiration is high may affect plant accumulation of pharmaceutical and personal care products (PPCPs) and endocrine disrupting chemicals (EDCs). In this study, carrot, lettuce, and tomato plants were grown in solution containing 16 PPCP/EDCs in either a cool-humid or a warm-dry environment. Leaf bioconcentration factors (BCF) were positively correlated with transpiration for chemical groups of different ionized states (p < 0.05). However, root BCFs were correlated with transpiration only for neutral PPCP/EDCs (p < 0.05). Neutral and cationic PPCP/EDCs showed similar accumulation, while anionic PPCP/EDCs had significantly higher accumulation in roots and significantly lower accumulation in leaves (p < 0.05). Results show that plant transpiration may play a significant role in the uptake and translocation of PPCP/EDCs, which may have a pronounced effect in arid and hot climates where irrigation with treated wastewater is common. - Highlights: • Leaf accumulation of PPCP/EDCs is related on plant transpiration. • Cationic and neutral PPCP/EDCs have similar leaf and root accumulation. • Anionic PPCP/EDCs have greater root accumulation and lesser leaf accumulation. • PPCP/EDCs are extensively metabolized in plant tissue and hydroponic solution. - High plant transpiration in arid and hot areas may lead to increased foliar accumulation of PPCP/EDCs from treated wastewater irrigation

  19. Defect accumulation behaviour in hcp metals and alloys

    International Nuclear Information System (INIS)

    Woo, C.H.

    2000-01-01

    The effects of displacement damage on the physical and mechanical properties of metals and alloys, caused by the bombardment of energetic particles, have been investigated for several decades. Besides the obvious technical and industrial implications, an important motive of such investigations is to understand the factors that differentiate the response of different metals under different irradiation conditions. Recently, much interest is shown in the possible effects of the crystal lattice structure on variations in the damage accumulation behaviour of metals and alloys. In this paper we focus on the case of metals and alloys that crystallize in the hexagonal close pack (hcp) structure, and describe recent understanding of the damage production, accumulation and its consequences in these metals

  20. Technological capability accumulation in the 'maquila industry' in Mexico

    Directory of Open Access Journals (Sweden)

    Gabriela Dutrénit

    Full Text Available From the mid-1960s, 'maquila' plants were established in the Mexican Northern border. The Mexican model was based on foreign firms establishing their own assembly plants. Even though this model was less successful than that of East and South East Asian in terms of several techno-economic indicators, it has largely contributed to employment generation. However, as a result of internal learning process and changes in the global firms strategies, several 'maquilas' operating in Mexico have undergone important qualitative changes. During the 1990s there was a change in the nature of their productive and technological activities towards more complex products and more innovative technological activities. In contrast, other dimensions have evolved slowly, such as the engagement of Mexican suppliers in global supply chains. The aim of this paper is to discuss an analytical framework to help study the technological capability accumulation in the 'maquila' industry in Mexico. Based on that the paper seeks to examine levels of technological capability accumulation of three maquilas, and to bring to light some stylized facts of the accumulation process in this industry. The analytical framework proposed draws on the taxonomy of technological capabilities proposed by Bell & Pavitt (1995 for the manufacturing industry in developing countries and its further adaptations and applications carried in Figueiredo (2001 and Ariffin & Figueiredo (2003, 2004. This paper adapts it to the particularities of the 'maquila' industry in Mexico. The new taxonomy includes technical functions that are relevant to this industry and redefines activities that correspond to various levels of accumulation. This paper is based on a case study methodology. The cases are the business lines of three maquilas in Ciudad Juarez: Thomson Multimedia, Philips Corp. and Delphi Corp. Two business lines correspond to the consumer electronics industry and the third is specialized on electronic

  1. Accumulation of advanced glycation endproducts reduces chondrocyte-mediated extracellular matrix turnover in human articular cartilage

    NARCIS (Netherlands)

    Degroot, J.; Verzijl, N.; Jacobs, K. M.; Budde, M.; Bank, R. A.; Bijlsma, J. W.; TeKoppele, J. M.; Lafeber, F. P.

    2001-01-01

    The prevalence of osteoarthritis (OAs) increases with age and coincides with the accumulation of advanced glycation endproducts (AGEs) in articular cartilage, suggesting that accumulation of glycation products may be involved in the development of OA. This study was designed to examine the effects

  2. Spatio-temporal reconstruction of air temperature maps and their application to estimate rice growing season heat accumulation using multi-temporal MODIS data.

    Science.gov (United States)

    Zhang, Li-wen; Huang, Jing-feng; Guo, Rui-fang; Li, Xin-xing; Sun, Wen-bo; Wang, Xiu-zhen

    2013-02-01

    The accumulation of thermal time usually represents the local heat resources to drive crop growth. Maps of temperature-based agro-meteorological indices are commonly generated by the spatial interpolation of data collected from meteorological stations with coarse geographic continuity. To solve the critical problems of estimating air temperature (T(a)) and filling in missing pixels due to cloudy and low-quality images in growing degree days (GDDs) calculation from remotely sensed data, a novel spatio-temporal algorithm for T(a) estimation from Terra and Aqua moderate resolution imaging spectroradiometer (MODIS) data was proposed. This is a preliminary study to calculate heat accumulation, expressed in accumulative growing degree days (AGDDs) above 10 °C, from reconstructed T(a) based on MODIS land surface temperature (LST) data. The verification results of maximum T(a), minimum T(a), GDD, and AGDD from MODIS-derived data to meteorological calculation were all satisfied with high correlations over 0.01 significant levels. Overall, MODIS-derived AGDD was slightly underestimated with almost 10% relative error. However, the feasibility of employing AGDD anomaly maps to characterize the 2001-2010 spatio-temporal variability of heat accumulation and estimating the 2011 heat accumulation distribution using only MODIS data was finally demonstrated in the current paper. Our study may supply a novel way to calculate AGDD in heat-related study concerning crop growth monitoring, agricultural climatic regionalization, and agro-meteorological disaster detection at the regional scale.

  3. The Epstein-Barr virus miR-BHRF1-1 targets RNF4 during productive infection to promote the accumulation of SUMO conjugates and the release of infectious virus.

    Science.gov (United States)

    Li, Jinlin; Callegari, Simone; Masucci, Maria G

    2017-04-01

    Post-translational modification by the Small Ubiquitin-like Modifier (SUMO) regulates a variety of cellular functions, and is hijacked by viruses to remodel the host cell during latent and productive infection. Here we have monitored the activity of the SUMO conjugation machinery in cells productively infected with Epstein-Barr virus (EBV). We found that SUMO2/3 conjugates accumulate during the late phase of the productive virus cycle, and identified several viral proteins as bone fide SUMOylation substrates. Analysis of the mechanism involved in the accumulation of SUMOylated proteins revealed upregulation of several components of the SUMO-conjugation machinery and post-transcriptional downregulation of the SUMO-targeted ubiquitin ligase RNF4. The latter effect was mediated by selective inhibition of RNF4 protein expression by the viral miR-BHRF1-1. Reconstitution of RNF4 in cells expressing an inducible miR-BHRF1-1 sponge or a miR-BHRF1-1 resistant RNF4 was associated with reduced levels of early and late viral proteins and impaired virus release. These findings illustrate a novel strategy for viral interference with the SUMO pathway, and identify the EBV miR-BHRF1-1 and the cellular RNF4 as regulators of the productive virus cycle.

  4. The Epstein-Barr virus miR-BHRF1-1 targets RNF4 during productive infection to promote the accumulation of SUMO conjugates and the release of infectious virus.

    Directory of Open Access Journals (Sweden)

    Jinlin Li

    2017-04-01

    Full Text Available Post-translational modification by the Small Ubiquitin-like Modifier (SUMO regulates a variety of cellular functions, and is hijacked by viruses to remodel the host cell during latent and productive infection. Here we have monitored the activity of the SUMO conjugation machinery in cells productively infected with Epstein-Barr virus (EBV. We found that SUMO2/3 conjugates accumulate during the late phase of the productive virus cycle, and identified several viral proteins as bone fide SUMOylation substrates. Analysis of the mechanism involved in the accumulation of SUMOylated proteins revealed upregulation of several components of the SUMO-conjugation machinery and post-transcriptional downregulation of the SUMO-targeted ubiquitin ligase RNF4. The latter effect was mediated by selective inhibition of RNF4 protein expression by the viral miR-BHRF1-1. Reconstitution of RNF4 in cells expressing an inducible miR-BHRF1-1 sponge or a miR-BHRF1-1 resistant RNF4 was associated with reduced levels of early and late viral proteins and impaired virus release. These findings illustrate a novel strategy for viral interference with the SUMO pathway, and identify the EBV miR-BHRF1-1 and the cellular RNF4 as regulators of the productive virus cycle.

  5. Complete Nutrient Removal Coupled to Nitrous Oxide Production as a Bioenergy Source by Denitrifying Polyphosphate-Accumulating Organisms.

    Science.gov (United States)

    Gao, Han; Liu, Miaomiao; Griffin, James S; Xu, Longcheng; Xiang, Da; Scherson, Yaniv D; Liu, Wen-Tso; Wells, George F

    2017-04-18

    Coupled aerobic-anoxic nitrous decomposition operation (CANDO) is a promising emerging bioprocess for wastewater treatment that enables direct energy recovery from nitrogen (N) in three steps: (1) ammonium oxidation to nitrite; (2) denitrification of nitrite to nitrous oxide (N 2 O); and (3) N 2 O conversion to N 2 with energy generation. However, CANDO does not currently target phosphorus (P) removal. Here, we demonstrate that denitrifying polyphosphate-accumulating organism (PAO) enrichment cultures are capable of catalyzing simultaneous biological N and P removal coupled to N 2 O generation in a second generation CANDO process, CANDO+P. Over 7 months (>300 cycles) of operation of a prototype lab-scale CANDO+P sequencing batch reactor treating synthetic municipal wastewater, we observed stable and near-complete N removal accompanied by sustained high-rate, high-yield N 2 O production with partial P removal. A substantial increase in abundance of the PAO Candidatus Accumulibacter phosphatis was observed, increasing from 5% of the total bacterial community in the inoculum to over 50% after 4 months. PAO enrichment was accompanied by a strong shift in the dominant Accumulibacter population from clade IIC to clade IA, based on qPCR monitoring of polyphosphate kinase 1 (ppk1) gene variants. Our work demonstrates the feasibility of combining high-rate, high-yield N 2 O production for bioenergy production with combined N and P removal from wastewater, and it further suggests a putative denitrifying PAO niche for Accumulibacter clade IA.

  6. Ethylene regulation of carotenoid accumulation and carotenogenic gene expression in colour-contrasted apricot varieties (Prunus armeniaca).

    Science.gov (United States)

    Marty, I; Bureau, S; Sarkissian, G; Gouble, B; Audergon, J M; Albagnac, G

    2005-07-01

    In order to elucidate the regulation mechanisms of carotenoid biosynthesis in apricot fruit (Prunus armeniaca), carotenoid content and carotenogenic gene expression were analysed as a function of ethylene production in two colour-contrasted apricot varieties. Fruits from Goldrich (GO) were orange, while Moniqui (MO) fruits were white. Biochemical analysis showed that GO accumulated precursors of the uncoloured carotenoids, phytoene and phytofluene, and the coloured carotenoid, beta-carotene, while Moniqui (MO) fruits only accumulated phytoene and phytofluene but no beta-carotene. Physiological analysis showed that ethylene production was clearly weaker in GO than in MO. Carotenogenic gene expression (Psy-1, Pds, and Zds) and carotenoid accumulation were measured with respect to ethylene production which is initiated in mature green fruits at the onset of the climacteric stage or following exo-ethylene or ethylene-receptor inhibitor (1-MCP) treatments. Results showed (i) systematically stronger expression of carotenogenic genes in white than in orange fruits, even for the Zds gene involved in beta-carotene synthesis that is undetectable in MO fruits, (ii) ethylene-induction of Psy-1 and Pds gene expression and the corresponding product accumulation, (iii) Zds gene expression and beta-carotene production independent of ethylene. The different results obtained at physiological, biochemical, and molecular levels revealed the complex regulation of carotenoid biosynthesis in apricots and led to suggestions regarding some possible ways to regulate it.

  7. Radionuclides accumulation in milk and its products

    Energy Technology Data Exchange (ETDEWEB)

    Marmuleva, N.I.; Barinov, E.Y.; Petukhov, V.L. [Novosibirsk State Agrarian University (Russian Federation)

    2003-05-01

    The problem of radioactive pollution is extremely urgent in Russia in connection with presence of territories polluted by radionuclides on places of nuclear tests, in zones around the enterprises on production, processing and storage of radioactive materials, and also in areas of emergency pollution (Barakhtin, 2001). The aim of our investigation was a determination of the levels of the main radioactive elements - {sup 137}Cs and {sup 90}Sr in diary products. 363 samples of milk, dry milk, butter, cheese and yogurt from Novosibirsk region were examined. {sup 137}Cs level was 3.7 to 9.2 times higher than {sup 90}Sr one in milk, cheese and yogurt. At the same time the level of these radio-nuclides in butter was identical (8.03 Bk/kg). (authors)

  8. Accumulation of organochlorines and brominated flame retardants in estuarine and marine food chains: Field measurements and model calculations

    NARCIS (Netherlands)

    Veltman, K.; Hendriks, J.; Huijbregts, M.; Leonards, P.E.G.; Heuvel-Greve, van den M.J.; Vethaak, D.

    2005-01-01

    Food chain accumulation of organochlorines and brominated flame retardants in estuarine and marine environments is compared to model estimations and fresh water field data. The food chain consists of herbivores, detritivores and primary and secondary carnivores i.e. fish, fish-eating birds and

  9. Overexpression of snapdragon Delila (Del) gene in tobacco enhances anthocyanin accumulation and abiotic stress tolerance

    OpenAIRE

    Naing, Aung Htay; Park, Kyeung Il; Ai, Trinh Ngoc; Chung, Mi Young; Han, Jeung Sul; Kang, Young-Wha; Lim, Ki Byung; Kim, Chang Kil

    2017-01-01

    Background Rosea1 (Ros1) and Delila (Del) co-expression controls anthocyanin accumulation in snapdragon flowers, while their overexpression in tomato strongly induces anthocyanin accumulation. However, little data exist on how Del expression alone influences anthocyanin accumulation. Results In tobacco (Nicotiana tabacum ?Xanthi?), Del expression enhanced leaf and flower anthocyanin production through regulating NtCHS, NtCHI, NtF3H, NtDFR, and NtANS transcript levels. Transgenic lines display...

  10. Yield accumulation in irrigated sugarcane. II. Utilization of intercepted radiation

    International Nuclear Information System (INIS)

    Muchow, R.C.; Evensen, C.I.; Osgood, R.V.; Robertson, M.J.

    1997-01-01

    Intercepted radiation is a major driving variable of crop production under high-input irrigated conditions. Quantitative information on the utilization of radiation in yield accumulation allows extrapolation beyond the current season and location, and when this information is incorporated into crop growth simulation models, the effect of crop age on the productivity of different cultivars can be examined under different climatic conditions. This paper examines the differential performance of high-yielding sugarcane (Saccharum spp. hybrids) crops in terms of the amount of short-wave solar radiation intercepted (Si) and the efficiency of use of intercepted radiation (RUE) in biomass production. Biomass accumulation during the 12- to 24-mo crop cycle was examined for two experiments conducted in Hawaii, and three experiments conducted in tropical Australia from 1991 to 1993. The analysis showed that (i) RUE was much less for growth after 12 mo than in the first 12 mo; (ii) maximum RUE of sugarcane approaches 2.0 g MJ(-1); (iii) biomass accumulation beyond 12 mo was not related directly to radiation utilization; and (iv) cultivars differed in Si, but differences in RUE could not be unequivocally assessed due to the confounding effect of variable recovery of trash in biomass estimates. It is concluded that stalk death and consequent biomass loss are important factors contributing to yield variation in sugarcane crops growing for 12 to 24 mo, with a yield plateau occurring at variable crop ages during the second year of growth

  11. Use of a running coupling in the NLO calculation of forward hadron production

    Science.gov (United States)

    Ducloué, B.; Iancu, E.; Lappi, T.; Mueller, A. H.; Soyez, G.; Triantafyllopoulos, D. N.; Zhu, Y.

    2018-03-01

    We address and solve a puzzle raised by a recent calculation [1] of the cross section for particle production in proton-nucleus collisions to next-to-leading order: the numerical results show an unreasonably large dependence upon the choice of a prescription for the QCD running coupling, which spoils the predictive power of the calculation. Specifically, the results obtained with a prescription formulated in the transverse coordinate space differ by 1 to 2 orders of magnitude from those obtained with a prescription in momentum space. We show that this discrepancy is an artifact of the interplay between the asymptotic freedom of QCD and the Fourier transform from coordinate space to momentum space. When used in coordinate space, the running coupling can act as a fictitious potential which mimics hard scattering and thus introduces a spurious contribution to the cross section. We identify a new coordinate-space prescription, which avoids this problem, and leads to results consistent with those obtained with the momentum-space prescription.

  12. Isotopes accumulation in the thermal column of TRIGA reactor

    International Nuclear Information System (INIS)

    Iorgulis, C.; Diaconu, D.; Gugiu, D.; Csaba, R.

    2013-01-01

    The correlation of impurity observed in the virgin graphite and radionuclide content and activities measured in the irradiated graphite needs to know the irradiated history. This is a challenging process if impurity content and irradiation conditions are not accurately known. This is the case of the irradiated graphite in the thermal column of Institute for Nuclear Research Pitesti (INR)14 MW TRIGA reactor. To overcome incomplete impurity content and the unknown position in the column of the measured irradiated graphite available for characterisation and comparison, a set of preliminary simulations were performed. Following Eu 152 /Eu 154 ration they allowed the estimation of an impurity content and irradiation conditions leading to measured activities. Based on these data the radio-isotope accumulation in different positions in the thermal column was predicted. Modelling performed by INR used advanced prediction packages (e.g. WIMS, MCNP ORIGEN-S from Scale 5) to assess the isotopic content of MTR graphite types with irradiation history specific for a TRIGA research reactor. Some certain calculations points from the column were selected in order to model the burnup and isotopes productions using ORIGEN from SCALE code system. (authors)

  13. Average dose to an organ per microcurie-day accumulated by a radionuclide in a source organ

    International Nuclear Information System (INIS)

    Snyder, W.S.; Ford, M.R.

    1975-01-01

    Methods are discussed that are used in calculations of the average radiation dose to an organ per microcurie/day accumulated by a radionuclide in a source organ. The dosimetric data on photons are obtained by Monte Carlo type computer calculations on a non-homogeneous phantom having the general form of the human body. (U.S.)

  14. Pulmonary Lipiodol Accumulation after Transarterial Chemoembolization: CT Findings and Its Radiologic Outcomes

    Energy Technology Data Exchange (ETDEWEB)

    Youn, In Young; Chong, Se Min; Kwak, Byung Kook; Shin, Hyung Jin; Seo, Gi Young; Seo, Jae Seung; Kim, Jae Kyun [Dept. of Radiology, Chung Ang University Medical Center, Chung Ang University College of Medicine, Seoul (Korea, Republic of)

    2011-12-15

    To evaluate CT findings and radiologic outcomes of pulmonary lipiodol accumulation (PLA) after transarterial chemoembolization (TACE). This retrospective study involved 488 TACEs for hepatocellular carcinoma (HCC) (n = 160) and hepatic metastasis for non-hepatic malignancies (n = 7) in 167 patients. We reviewed the patient clinicoradiologic findings before and after TACE and calculated the incidence of PLA and PLA resolution time after initial CT and after TACE. Lipiodol accumulation in the lungs was seen under CT after TACE in seven patients (M : F = 6 : 1, mean age 61 years). The incidence of PLA at CT was 4.1% (7/167 patients). In five patients, associated intrathoracic abnormalities including pleural effusion with (n 3) or without consolidation (n = 2) were revealed at CT scans. The CT resolution time and PLA recovery time were 56 {+-} 54 days and 66 {+-} 52 days, respectively. The recovery time for lipiodol accumulation was 66 days. It is believed that the clinical and radiologic outcome of PLA without respiratory failure is promising, and conservative treatment will suffice when lipiodol accumulation in the lungs is seen in CT images after TACE.

  15. Microbial biodiesel production from oil palm biomass hydrolysate using marine Rhodococcus sp. YHY01.

    Science.gov (United States)

    Bhatia, Shashi Kant; Kim, Junyoung; Song, Hun-Seok; Kim, Hyun Joong; Jeon, Jong-Min; Sathiyanarayanan, Ganesan; Yoon, Jeong-Jun; Park, Kyungmoon; Kim, Yun-Gon; Yang, Yung-Hun

    2017-06-01

    The effect of various biomass derived inhibitors (i.e. furfural, hydroxymethylfurfural (HMF), vanillin, 4-hydroxy benzaldehyde (4-HB) and acetate) was investigated for fatty acid accumulation in Rhodococcus sp. YHY 01. Rhodococcus sp. YHY01 was able to utilize acetate, vanillin, and 4-HB for biomass production and fatty acid accumulation. The IC 50 value for furfural (3.1mM), HMF (3.2mM), vanillin (2.0mM), 4-HB (2.7mM) and acetate (3.7mM) was calculated. HMF and vanillin affect fatty acid composition and increase saturated fatty acid content. Rhodococcus sp. YHY 01 cultured with empty fruit bunch hydrolysate (EFBH) as the main carbon source resulted in enhanced biomass (20%) and fatty acid productivity (37%), in compression to glucose as a carbon source. Overall, this study showed the beneficial effects of inhibitory molecules on growth and fatty acid production, and support the idea of biomass hydrolysate utilization for biodiesel production by avoiding complex efforts to remove inhibitory compounds. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Method for assessing the probability of accumulated doses from an intermittent source using the convolution technique

    International Nuclear Information System (INIS)

    Coleman, J.H.

    1980-10-01

    A technique is discussed for computing the probability distribution of the accumulated dose received by an arbitrary receptor resulting from several single releases from an intermittent source. The probability density of the accumulated dose is the convolution of the probability densities of doses from the intermittent releases. Emissions are not assumed to be constant over the brief release period. The fast fourier transform is used in the calculation of the convolution

  17. ACCUMULATION OF POLYHYDROXYALKANOIC ACIDS BY AZOTOBACTER CHROOCOCCUM MAL-201 FROM ORGANIC WASTE

    Directory of Open Access Journals (Sweden)

    Soma Pal Saha

    2013-08-01

    Full Text Available Azotobacter chroococcum MAL-201 (MTCC 3853, a free-living nitrogen-fixing bacterium accumulated intracellular poly(3-hydroxybutyric acid [P(3HB] accounting 69% of cell dry weight (CDW when grown in nitrogrn-free Stockdale medium containing 2% (w/v glucose. It also produced copolymer of poly(3-hydroxybutyrate co-3-hydroxyvalerate [P(3HB-co-3HV] using glucose as primary carbon source and valerate cas cosubstrate. To make the polymer production cost effective four types of waste material of different origin were tested for growth and polymer production. Stockdale medium supplemented with 1% (w/v waste materials failed to yield good growth and polymer accumulation. Two–step cultivation was adopted for better growth and enhanced polymer accumulation. The candy factory waste was most suitable for synthesis of P(3HB accounting 17.8 and 40.58% using single and two-step cultivation conditions respectively. Wastes of domestic and poultry origin produced P(3HB-co-3HV with 3HV content 28.8 and 21.5 mol% respectively in two-step cultivation. Increase concentration of these wastes resulted in further upliftment of 3HV content of polymer with reduced growth and polymer accumulation. However, at optimum incubation the strain MAL-201 cells accumulated P(3HB 48.5% of CDW (at 40h from candy factory waste and P(3HB-co-3HV 24.75 % of CDW with 3HV 34.65 mol % from domestic waste. Intrinsic viscosity, molecular weight and thermal degradation of the polymers accumulated in the cells grown in glucose, glucose with valerate and glucose with waste were compared.

  18. Environmental and genetic factors associated with solanesol accumulation in potato leaves

    Directory of Open Access Journals (Sweden)

    Raymond Campbell

    2016-08-01

    Full Text Available Solanesol is a high value 45-carbon, unsaturated, all-trans-nonaprenol isoprenoid. Recently solanesol has received particular attention because of its utility, both in its own right and as a precursor in the production of numerous compounds used in the treatment of disease states. Solanesol is found mainly in solanaceous crops such as potato, tomato, tobacco and pepper where it accumulates in the foliage. There is considerable potential to explore the extraction of solanesol from these sources as a valuable co-product. In this study we have characterised the genetic variation in leaf solanesol content in a biparental, segregating diploid potato population. We demonstrate that potato leaf solanesol content is genetically controlled and identify several quantitative trait loci associated with leaf solanesol content. Transient over-expression of genes from the methylerythritol 4-phosphate (MEP and mevalonic acid (MVA pathways, either singly or in combination, resulted in enhanced accumulation of solanesol in leaves of Nicotiana benthamiana, providing insights for genetically engineering the pathway. We also demonstrate that in potato, leaf solanesol content is enhanced by up to six-fold on exposure to moderately elevated temperature and show corresponding changes in expression patterns of MEP and MVA genes. Our combined approaches offer new insights into solanesol accumulation and strategies for developing a bio-refinery approach to potato production.

  19. Water Management Practices Affect Arsenic and Cadmium Accumulation in Rice Grains

    OpenAIRE

    Sun, Liming; Zheng, Manman; Liu, Hongyan; Peng, Shaobing; Huang, Jianliang; Cui, Kehui; Nie, Lixiao

    2014-01-01

    Cadmium (Cd) and arsenic (As) accumulation in rice grains is a great threat to its productivity, grain quality, and thus human health. Pot and field studies were carried out to unravel the effect of different water management practices (aerobic, aerobic-flooded, and flooded) on Cd and As accumulation in rice grains of two different varieties. In pot experiment, Cd or As was also added into the soil as treatment. Pots without Cd or As addition were maintained as control. Results indicated that...

  20. The effects of dietary calcium iodate on productive performance, egg quality and iodine accumulation in eggs of laying hens.

    Science.gov (United States)

    Bakhshalinejad, R; Hassanabadi, A; Nassiri-Moghaddam, H; Zarghi, H

    2018-01-25

    The aim of this study was to examine the effects of various levels of supplemental calcium iodate (CI) on productive performance, egg quality, blood indices and iodine (I) accumulation in the eggs in commercial laying hens. A total of 240 White Leghorn layers (Hy-line W36) were divided through a completely randomized design into six treatments with five replicates and eight hens per each at 32 weeks of age. This experiment lasted for 12 weeks. Concentrations of I in the mash diets were 0.74, 3.13, 5.57, 8.11, 10.65 and 12.94 mg I/kg of feed in treatments 1-6 respectively. The added doses of CI were included 0.0 (control), 2.5, 5.0, 7.5, 10.0 and 12.5 mg/kg of diet for treatments 1-6 respectively. There were no significant differences in productive performance among the treatments. The highest eggshell strength was observed in group fed diet containing 3.13 mg I/kg (p = .014). The highest percentage of calcium and lowest percentage of phosphorus in eggshell were observed in group fed diet containing 12.94 mg I/kg (p = .0001). Feeding hens with diet containing 12.94 mg I/kg increased serum triiodothyronine-to-thyroxine ratio (p = .0001). Serum alanine aminotransferase activity in hens fed diet containing 12.94 mg I/kg was significantly more than control (p = .041). Blood Serum triglycerides in hens fed diet containing 8.11 mg I/kg were significantly higher than control (p = .0001). Edible fraction of the eggs of birds fed diet containing 12.94 mg I/kg was enriched by I almost 3 times more than those fed diet containing 0.74 mg I/kg. The results suggested that egg production, egg mass, feed intake and feed conversion ratio were not significantly affected by dietary I levels. Iodine accumulation in the eggs were increased by increasing dietary I levels and the level of 10 mg/kg CI could supply I enrichment of the eggs. © 2018 Blackwell Verlag GmbH.

  1. Calculation of low-energy reactor neutrino spectra reactor for reactor neutrino experiments

    Energy Technology Data Exchange (ETDEWEB)

    Riyana, Eka Sapta; Suda, Shoya; Ishibashi, Kenji; Matsuura, Hideaki [Dept. of Applied Quantum Physics and Nuclear Engineering, Kyushu University, Kyushu (Japan); Katakura, Junichi [Dept. of Nuclear System Safety Engineering, Nagaoka University of Technology, Nagaoka (Japan)

    2016-06-15

    Nuclear reactors produce a great number of antielectron neutrinos mainly from beta-decay chains of fission products. Such neutrinos have energies mostly in MeV range. We are interested in neutrinos in a region of keV, since they may take part in special weak interactions. We calculate reactor antineutrino spectra especially in the low energy region. In this work we present neutrino spectrum from a typical pressurized water reactor (PWR) reactor core. To calculate neutrino spectra, we need information about all generated nuclides that emit neutrinos. They are mainly fission fragments, reaction products and trans-uranium nuclides that undergo negative beta decay. Information in relation to trans-uranium nuclide compositions and its evolution in time (burn-up process) were provided by a reactor code MVP-BURN. We used typical PWR parameter input for MVP-BURN code and assumed the reactor to be operated continuously for 1 year (12 months) in a steady thermal power (3.4 GWth). The PWR has three fuel compositions of 2.0, 3.5 and 4.1 wt% {sup 235}U contents. For preliminary calculation we adopted a standard burn-up chain model provided by MVP-BURN. The chain model treated 21 heavy nuclides and 50 fission products. The MVB-BURN code utilized JENDL 3.3 as nuclear data library. We confirm that the antielectron neutrino flux in the low energy region increases with burn-up of nuclear fuel. The antielectron-neutrino spectrum in low energy region is influenced by beta emitter nuclides with low Q value in beta decay (e.g. {sup 241}Pu) which is influenced by burp-up level: Low energy antielectron-neutrino spectra or emission rates increase when beta emitters with low Q value in beta decay accumulate. Our result shows the flux of low energy reactor neutrinos increases with burn-up of nuclear fuel.

  2. Data to calculate emissions intensity for individual beef cattle reared on pasture-based production systems

    Directory of Open Access Journals (Sweden)

    G.A. McAuliffe

    2018-04-01

    Full Text Available With increasing concern about environmental burdens originating from livestock production, the importance of farming system evaluation has never been greater. In order to form a basis for trade-off analysis of pasture-based cattle production systems, liveweight data from 90 Charolais × Hereford-Friesian calves were collected at a high temporal resolution at the North Wyke Farm Platform (NWFP in Devon, UK. These data were then applied to the Intergovernmental Panel on Climate Change (IPCC modelling framework to estimate on-farm methane emissions under three different pasture management strategies, completing a foreground dataset required to calculate emissions intensity of individual beef cattle.

  3. Response of salt-marsh carbon accumulation to climate change.

    Science.gov (United States)

    Kirwan, Matthew L; Mudd, Simon M

    2012-09-27

    About half of annual marine carbon burial takes place in shallow water ecosystems where geomorphic and ecological stability is driven by interactions between the flow of water, vegetation growth and sediment transport. Although the sensitivity of terrestrial and deep marine carbon pools to climate change has been studied for decades, there is little understanding of how coastal carbon accumulation rates will change and potentially feed back on climate. Here we develop a numerical model of salt marsh evolution, informed by recent measurements of productivity and decomposition, and demonstrate that competition between mineral sediment deposition and organic-matter accumulation determines the net impact of climate change on carbon accumulation in intertidal wetlands. We find that the direct impact of warming on soil carbon accumulation rates is more subtle than the impact of warming-driven sea level rise, although the impact of warming increases with increasing rates of sea level rise. Our simulations suggest that the net impact of climate change will be to increase carbon burial rates in the first half of the twenty-first century, but that carbon-climate feedbacks are likely to diminish over time.

  4. Selecting and calculating joint operation of oil and petroleum gas collection systems, and mechanized production methods

    Energy Technology Data Exchange (ETDEWEB)

    Guseva, L S; D' yachuk, A I; Davydova, L V; Maslov, V P; Salyautdinova, R M; Suslov, V M

    1979-01-01

    The possibility is examined of formalizing the indicated procedure in the process of performing step by step calculations. At the first step, considering limitations imposed by the dominating parameters, preliminary selection is performed of the acceptable combination of the type of collection system and methods of mechanized production for the development conditions examined. The second step provides for physical simulation at a well of an experimental section of time-variable conditions of field development. The values of the technological indices thus defined are then considered to be reliable information for technico-economic calculations. Parallel research is done on the technological features of operation of the collection systems chosen and their individual elements (pipeline system, separation units, etc.), which the experimental section is fitted with beforehand. Material is given which illustrates in detail the basic assumptions of the technique proposed and the calculation procedure.

  5. Hydroponic screening of black locust families for heavy metal tolerance and accumulation.

    Science.gov (United States)

    Župunski, Milan; Borišev, Milan; Orlović, Saša; Arsenov, Danijela; Nikolić, Nataša; Pilipović, Andrej; Pajević, Slobodanka

    2016-01-01

    Present work examines phytoextraction potential of four black locust families (half-sibs 54, 56, 115, and 135) grown hydroponically. Plants were treated with 6 ppm of cadmium (Cd), 100 ppm of nickel (Ni), and 40 ppm of lead (Pb) added in Hoagland nutrient solution, accompanying with simultaneously applied all three metals. Responses to metals exposure among families were different, ranging from severe to slight reduction of root and shoot biomass production of treated plants. Calculated tolerance indices are indicating tested families as highly tolerant (Ti > 60). Family 135 had the lowest tolerance index, pointing that it was highly susceptible to applied metals. Comparing photosynthetic activities of tested families it has been noticed that they were highly sensitive to stress induced by heavy metals. Net photosynthetic rate of nickel treated plants was the most affected by applied concentration. Cadmium and nickel concentrations in stems and leaves of black locust families exceeded 100 mg Cd kg(-1) and 1000 mg Ni kg(-1), in both single and multipollution context. On the contrary, accumulation of lead in above ground biomass was highly affected by multipollution treatment. Tf and BCF significantly varied between investigated treatments and families of black locust. Concerning obtained results of heavy metals accumulation and tolerance of black locust families can be concluded that tested families might be a promising tool for phytoextraction purposes, but it takes to be further confirmed in field trials.

  6. Evaluation of radiation use efficiency and its relationship with dry matter accumulation in three millet species

    Directory of Open Access Journals (Sweden)

    behnam kamkar

    2009-06-01

    Full Text Available A factorial arrangement of three millets species (Panicum miliaceum, Pennisetum glaucum, and Setaria italica and two sowing dates with three replications were used in a completely randomized design to evaluate the radiation use efficiency and its relationship with dry matter accumulation. Leaf area index was used in daily intervals to calculate daily intercepted radiation. Light extinction coefficient was calculated as the slope of regression line between log transformed fraction of intercepted radiation and leaf area index during growing season. Radiation use efficiency was calculated as the slope of linear regression between cumulative intercepted radiation and cumulative biomass during growing season. Results showed that light extinction coefficient and radiation use efficiency for proso, pearl and foxtail millets were 0.75, 0.66, 0.57 and 1.43, 1.83, 1.74 g/MJ in terms of total radiation, respectively. Differences in biomass production were not significant between proso and pearl millets. Proso millet had higher intercepted radiation, but lower radiation use efficiency in comparison with pearl millet. Foxtail millet had lower intercepted radiation than proso and pearl millets, but its radiation use efficiency was higher than pearl millet. Total biomass of foxtail millet was lower than other species. Results indicated that proso and pearl millets can produce more biomass than foxtail millet.

  7. Concentration creation of system and applied software of reactor calculations

    International Nuclear Information System (INIS)

    Zizin, M.N.

    1995-01-01

    Basic concept provisions, including modularity, openness and machine-independent programs; accumulation of procedure knowledge in form of computer module library; creation of medium facilitating module development and accompanying; possibility of head programs automated generation and user-friendly interface are presented. Intellectual program shell ShIPR for mathematical reactor modeling, the final goal whereof consists in automated generation of machine-independent programs in the Fortran 77 language on the basis of calculation moduli and accumulated knowledge base, is developed on the basis of the above concept

  8. Defect accumulation under cascade damage conditions

    DEFF Research Database (Denmark)

    Trinkaus, H.; Singh, B.N.; Woo, C.H.

    1994-01-01

    in terms of this reaction kinetics taking into account cluster production, dissociation, migration and annihilation at extended sinks. Microstructural features which are characteristic of cascade damage and cannot be explained in terms of the conventional single defect reaction kinetics are emphasized......There is now ample evidence from both experimental and computer simulation studies that in displacement cascades not only intense recombination takes place but also efficient clustering of both self-interstitial atoms (SIAs) and vacancies. The size distributions of the two types of defects produced...... reactions kinetics associated with the specific features of cascade damage is described, with emphasis on asymmetries between SIA and vacancy type defects concerning their production, stability, mobility and interactions with other defects. Defect accumulation under cascade damage conditions is discussed...

  9. CACA-2: revised version of CACA-a heavy isotope and fission-product concentration calculational code for experimental irradiation capsules

    International Nuclear Information System (INIS)

    Allen, E.J.

    1976-02-01

    A computer program is described which calculates nuclide concentration histories, power or neutron flux histories, burnups, and fission-product birthrates for fueled experimental capsules subjected to neutron irradiations. Seventeen heavy nuclides in the chain from 232 Th to 242 Pu and a user-specified number of fission products are treated. A fourth-order Runge-Kutta calculational method solves the differential equations for nuclide concentrations as a function of time. For a particular problem, a user-specified number of fuel regions may be treated. A fuel region is described by volume, length, and specific irradiation history. A number of initial fuel compositions may be specified for each fuel region. The irradiation history for each fuel region can be divided into time intervals, and a constant power density or a time-dependent neutron flux is specified for each time interval. Also, an independent cross-section set may be selected for each time interval in each irradiation history. The fission-product birthrates for the first composition of each fuel region are summed to give the total fission-product birthrates for the problem

  10. Carbon Calculator for Land Use Change from Biofuels Production (CCLUB). Users' manual and technical documentation.

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, S; Dunn, JB; Wang, M (Energy Systems); (Univ. of Illinois at Chicago)

    2012-06-07

    The Carbon Calculator for Land Use Change from Biofuels Production (CCLUB) calculates carbon emissions from land use change (LUC) for four different ethanol production pathways including corn grain ethanol and cellulosic ethanol from corn stover, miscanthus, and switchgrass. This document discusses the version of CCLUB released May 31, 2012 which includes corn, as did the previous CCLUB version, and three cellulosic feedstocks: corn stover, miscanthus, and switchgrass. CCLUB calculations are based upon two data sets: land change areas and above- and below-ground carbon content. Table 1 identifies where these data are stored and used within the CCLUB model, which is built in MS Excel. Land change area data is from Purdue University's Global Trade Analysis Project (GTAP) model, a computable general equilibrium (CGE) economic model. Section 2 describes the GTAP data CCLUB uses and how these data were modified to reflect shrubland transitions. Feedstock- and spatially-explicit below-ground carbon content data for the United States were generated with a surrogate model for CENTURY's soil organic carbon sub-model (Kwon and Hudson 2010) as described in Section 3. CENTURY is a soil organic matter model developed by Parton et al. (1987). The previous CCLUB version used more coarse domestic carbon emission factors. Above-ground non-soil carbon content data for forest ecosystems was sourced from the USDA/NCIAS Carbon Online Estimator (COLE) as explained in Section 4. We discuss emission factors used for calculation of international greenhouse gas (GHG) emissions in Section 5. Temporal issues associated with modeling LUC emissions are the topic of Section 6. Finally, in Section 7 we provide a step-by-step guide to using CCLUB and obtaining results.

  11. FPDCYS and FPSPEC: computer programs for calculating fission-product beta and gamma multigroup spectra from ENDF/B-IV data

    International Nuclear Information System (INIS)

    Stamatelatos, M.G.; England, T.R.

    1977-05-01

    FPDCYS and FPSPEC are two FORTRAN computer programs used at the Los Alamos Scientific Laboratory (LASL), in conjunction with the CINDER-10 program, for calculating cumulative fission-product beta and/or gamma multigroup spectra in arbitrary energy structures, and for arbitrary neutron irradiation periods and cooling times. FPDCYS processes ENDF/B-IV fission-product decay energy data to generate multigroup beta and gamma spectra from individual ENDF/B-IV fission-product nuclides. FPSPEC further uses these spectra and the corresponding nuclide activities calculated by the CINDER-10 code to produce cumulative beta and gamma spectra in the same energy grids in which FPDCYS generates individual isotope decay spectra. The code system consisting of CINDER-10, FPDCYS, and FPSPEC has been used for comparisons with experimental spectra and continues to be used at LASL for generating spectra in special user-oriented group structures. 3 figures

  12. Accumulation of organic compounds leached from plastic materials used in biopharmaceutical process containers.

    Science.gov (United States)

    Jenke, Dennis R; Zietlow, David; Garber, Mary Jo; Sadain, Salma; Reiber, Duane; Terbush, William

    2007-01-01

    Plastic materials are widely used in medical items, such as solution containers, transfusion sets, transfer tubing, and devices. An emerging trend in the biotechnology industry is the utilization of plastic containers to prepare, transport, and store an assortment of solutions including buffers, media, and in-process and finished product. The direct contact of such containers with the product at one or more points in its lifetime raises the possibility that container leachables may accumulate in the finished product. The interaction between several commercially available container materials and numerous model test solutions (representative of buffers and media used in biopharmaceutical applications) was investigated. This paper summarizes the identification of leachables associated with the container materials and documents the levels to which targeted leachables accumulate in the test solutions under defined storage conditions.

  13. Simultaneous improvement in production of microalgal biodiesel and high-value alpha-linolenic acid by a single regulator acetylcholine.

    Science.gov (United States)

    Parsaeimehr, Ali; Sun, Zhilan; Dou, Xiao; Chen, Yi-Feng

    2015-01-01

    Photoautotrophic microalgae are a promising avenue for sustained biodiesel production, but are compromised by low yields of biomass and lipids at present. We are developing a chemical approach to improve microalgal accumulation of feedstock lipids as well as high-value alpha-linolenic acid which in turn might provide a driving force for biodiesel production. We demonstrate the effectiveness of the small bioactive molecule "acetylcholine" on accumulation of biomass, total lipids, and alpha-linolenic acid in Chlorella sorokiniana. The effectiveness exists in different species of Chlorella. Moreover, the precursor and analogs of acetylcholine display increased effectiveness at higher applied doses, with maximal increases by 126, 80, and 60% over controls for biomass, total lipids, and alpha-linolenic acid, respectively. Production of calculated biodiesel was also improved by the precursor and analogs of acetylcholine. The biodiesel quality affected by changes in microalgal fatty acid composition was addressed. The chemical approach described here could improve the lipid yield and biodiesel production of photoautotrophic microalgae if combined with current genetic approaches.

  14. Accumulation of carbon in northern mire ecosystems

    Energy Technology Data Exchange (ETDEWEB)

    Tolonen, K; Turunen, J; Alm, J [Joensuu Univ. (Finland). Dept. of Biology; Korhola, A [Helsinki Univ. (Finland). Lab. of Physical Geography; Jungner, H [Helsinki Univ. (Finland). Dating Lab.; Vasander, H [Helsinki Univ. (Finland). Dept. of Forest Ecology

    1997-12-31

    The basic feature in the functional ecology of any mire ecosystem is retardation of the effective decay of organic material resulting in a conspicuous accumulation of plant debris as peat overtime. The carbon accumulation process is slow, and climatic change may have an impact on the carbon cycle of peatlands, therefore, it has been of interest to study the rate of carbon accumulation by geological methods from dated peat strata. The approach is hampered by several facts. First, the mires vary enormously as to their vegetation and hydrology and hence their production and decay properties. It follows that a great number of study sites are needed. Second, the peat in mires expands both vertically and laterally, and this requires a spatial reconstruction of carbon accumulation within a mire basin. Third, simple geological methods cannot account for the actual rate of carbon accumulation in peat, and finally, an additional carbon sink in the mire ecosystems can be the mineral subsoil beneath peat. The proposed warming will perhaps shift northwards the existing climatic mire regimes and, thus, the northern aapa fens will change to Sphagnum bogs that are more effective in sequestering carbon, but distinctly less effective in their CH{sub 4} and N{sub 2}O emanation. The role of mire fires in more remote northern areas may then become another important factor. The answer to the important question of future total sequestration of carbon to peatlands depends on the precipitation and its seasonal distribution pattern. Most climatic scenarios predict a decrease in the evaporation surplus during the summer at northern regions. Presumably, the consequent lowering of the water table would improve growth of forest on mires and simultaneously decrease the methane fluxes from peat. The combined net effect could be a clear restraining of the radiative forcing

  15. Accumulation of carbon in northern mire ecosystems

    Energy Technology Data Exchange (ETDEWEB)

    Tolonen, K.; Turunen, J.; Alm, J. [Joensuu Univ. (Finland). Dept. of Biology; Korhola, A. [Helsinki Univ. (Finland). Lab. of Physical Geography; Jungner, H. [Helsinki Univ. (Finland). Dating Lab.; Vasander, H. [Helsinki Univ. (Finland). Dept. of Forest Ecology

    1996-12-31

    The basic feature in the functional ecology of any mire ecosystem is retardation of the effective decay of organic material resulting in a conspicuous accumulation of plant debris as peat overtime. The carbon accumulation process is slow, and climatic change may have an impact on the carbon cycle of peatlands, therefore, it has been of interest to study the rate of carbon accumulation by geological methods from dated peat strata. The approach is hampered by several facts. First, the mires vary enormously as to their vegetation and hydrology and hence their production and decay properties. It follows that a great number of study sites are needed. Second, the peat in mires expands both vertically and laterally, and this requires a spatial reconstruction of carbon accumulation within a mire basin. Third, simple geological methods cannot account for the actual rate of carbon accumulation in peat, and finally, an additional carbon sink in the mire ecosystems can be the mineral subsoil beneath peat. The proposed warming will perhaps shift northwards the existing climatic mire regimes and, thus, the northern aapa fens will change to Sphagnum bogs that are more effective in sequestering carbon, but distinctly less effective in their CH{sub 4} and N{sub 2}O emanation. The role of mire fires in more remote northern areas may then become another important factor. The answer to the important question of future total sequestration of carbon to peatlands depends on the precipitation and its seasonal distribution pattern. Most climatic scenarios predict a decrease in the evaporation surplus during the summer at northern regions. Presumably, the consequent lowering of the water table would improve growth of forest on mires and simultaneously decrease the methane fluxes from peat. The combined net effect could be a clear restraining of the radiative forcing

  16. Letters of Gold: Enabling Primitive Accumulation through Neoliberal Conservation

    NARCIS (Netherlands)

    B.E. Büscher (Bram)

    2009-01-01

    textabstractAbstract: In Capital I, Marx wrote that the history of the separation of the producers from the means of production “is written in the annals of mankind in letters of blood and fire” (Marx, 1976: 875). This ‘so-called primitive accumulation’, or ‘accumulation by dispossession’ in David

  17. Bladder dose accumulation based on a biomechanical deformable image registration algorithm in volumetric modulated arc therapy for prostate cancer

    International Nuclear Information System (INIS)

    Andersen, E S; Muren, L P; Thor, M; Petersen, J B; Tanderup, K; Sørensen, T S; Noe, K Ø; Høyer, M; Bentzen, L

    2012-01-01

    Variations in bladder position, shape and volume cause uncertainties in the doses delivered to this organ during a course of radiotherapy for pelvic tumors. The purpose of this study was to evaluate the potential of dose accumulation based on repeat imaging and deformable image registration (DIR) to improve the accuracy of bladder dose assessment. For each of nine prostate cancer patients, the initial treatment plan was re-calculated on eight to nine repeat computed tomography (CT) scans. The planned bladder dose–volume histogram (DVH) parameters were compared to corresponding parameters derived from DIR-based accumulations as well as DVH summation based on dose re-calculations. It was found that the deviations between the DIR-based accumulations and the planned treatment were substantial and ranged (−0.5–2.3) Gy and (−9.4–13.5) Gy for D 2% and D mean , respectively, whereas the deviations between DIR-based accumulations and DVH summation were small and well within 1 Gy. For the investigated treatment scenario, DIR-based bladder dose accumulation did not result in substantial improvement of dose estimation as compared to the straightforward DVH summation. Large variations were found in individual patients between the doses from the initial treatment plan and the accumulated bladder doses. Hence, the use of repeat imaging has a potential for improved accuracy in treatment dose reporting. (paper)

  18. TRIGA fuel element burnup determination by measurement and calculation

    International Nuclear Information System (INIS)

    Zagar, T.; Ravnik, M.; Persic, A.; Jeraj, R.

    2000-01-01

    To estimate the accuracy of the fuel element burnup calculation different factors influencing the calculation were studied. To cover different aspects of burnup calculations, two in-house developed computer codes were used in calculations. The first (TRIGAP) is based on a one-dimensional two-group diffusion approximation, and the second (TRIGLAV) is based on a two-dimensional four-group diffusion equation. Both codes use WIMSD program with different libraries forunit-cell cross section data calculation. The burnup accumulated during the operating history of the TRIGA reactor at Josef Stefan Institute was calculated for all fuel elements. Elements used in the core during this period were standard SS 8.5% fuel elements, standard SS 12% fuel elements and highly enriched FLIP fuel elements. During the considerable period of operational history, FLIP and standard fuel elements were used simultaneously in mixed cores. (authors)

  19. Carbonate-silicate cycle models of the long-term carbon cycle, carbonate accumulation in the oceans, and climate

    International Nuclear Information System (INIS)

    Caldeira, K.G.

    1991-01-01

    Several models of the long-term carbon cycle, incorporating models of the carbonate-silicate cycle, were developed and utilized to investigate issues relating to global climate and the causes and consequences of changes in calcium carbonate accumulation in the oceans. Model results indicate that the marked mid-Cretaceous (120 Ma) global warming could be explained by increased rates of release of carbon dioxide from subduction-zone metamorphism and mid-ocean-ridges, in conjunction with paleogeographic factors. Since the mid-Cretaceous, the primary setting for calcium carbonate accumulation in the oceans has shifted from shallow-water to deep-water environments. Model results suggest that this shift could have major consequences for the carbonate-silicate cycle and climate, and lead to significant increases in the flux of metamorphic carbon dioxide to the atmosphere. Increases in pelagic carbonate productivity, and decreases in tropical shallow-water area available for neritic carbonate accumulation, have both been proposed as the primary cause of this shift. Two lines of evidence developed here (one involving a statistical analysis of Tertiary carbonate-accumulation and oxygen-isotope data, and another based on modeling the carbonate-silicate cycle and ocean chemistry) suggest that a decrease in tropical shallow-water area was more important than increased pelagic productivity in explaining this shift. Model investigations of changes in ocean chemistry at the Cretaceous/Tertiary (K/T) boundary (66 Ma) indicate that variations in deep-water carbonate productivity may affect shallow-water carbonate accumulation rates through a mechanism involving surface-water carbonate-ion concentration. In the aftermath of the K/T boundary event, deep-water carbonate production and accumulation were significantly reduced as a result of the extinction of calcareous plankton

  20. Benchmark calculations on residue production within the EURISOL DS project. Part 1: thin targets

    Energy Technology Data Exchange (ETDEWEB)

    David, J.C.; Blideanu, V.; Boudard, A.; Dore, D.; Leray, S.; Rapp, B.; Ridikas, D.; Thiolliere, N

    2006-12-15

    We have begun this benchmark study using mass distribution data of reaction products obtained at GSI in inverse kinematics. This step has allowed us to make a first selection among 10 spallation models; in this way the first assessment of the quality of the models was obtained. Then, in a second part, experimental mass distributions for some elements, which either are interesting as radioactive ion beams or important due to the safety and radioprotection issues (alpha or gamma emitters), will be also compared to model calculations. These data have been obtained for an equivalent 0.8 or 1.0 GeV proton beam, which is approximately the proposed projectile energy. We note that in realistic thick targets the proton beam will be slowed down and some secondary particles will be produced. Therefore, the residual nuclei production at lower energies is also important. For this reason, we also performed in the third part of this work some excitation function calculations and the associated data obtained with gamma-spectroscopy to test the models in a wide projectile energy range. We conclude that INCL4/Abla and Isabel/Abla are the best model combinations which we recommend. We also note that the agreement between model and data are better with 1 GeV protons than with 100-200 MeV protons.

  1. Hormonal effect on polyphenol accumulation in Cassia tissues cultured in vitro

    Energy Technology Data Exchange (ETDEWEB)

    Shah, R R; Subbaiah, K V; Mehta, A R

    1976-06-01

    Effects of auxin and kinetin on growth and production of phenolic compounds in cultured Cassia fistula L. tissues were examined. Initiation of polyphenols was largely determined by the auxin concentration in the medium. Growth of the cells in relation to accumulation of polyphenols was studied at different auxin and kinetin concentrations. The accumulation of phenolic materials was essentially restricted to the most rapid phase of the growth cycle. Progressive changes in the pattern of peroxidase activity were followed and their relationship with polyphenol synthesis is examined.

  2. Uneconomical top calculation method

    International Nuclear Information System (INIS)

    De Noord, M.; Vanm Sambeek, E.J.W.

    2003-08-01

    The methodology used to calculate the financial gap of renewable electricity sources and technologies is described. This methodology is used for calculating the production subsidy levels (MEP subsidies) for new renewable electricity projects in 2004 and 2005 in the Netherlands [nl

  3. Characterization of accumulated precipitates during subsurface iron removal

    International Nuclear Information System (INIS)

    Halem, Doris van; Vet, Weren de; Verberk, Jasper; Amy, Gary; Dijk, Hans van

    2011-01-01

    normal production wells. Other groundwater constituents, such as Mn, As and Sr were found to co-accumulate with Fe. Acid extraction and ESEM-EDX showed that Ca occurred together with Fe and by X-ray Powder Diffraction it was identified as calcite.

  4. Effect of Transpiration on Plant Accumulation and Translocation of PPCP/EDCs

    Science.gov (United States)

    Dodgen, Laurel K; Ueda, Aiko; Wu, Xiaoqin; Parker, David R; Gan, Jay

    2015-01-01

    The reuse of treated wastewater for agricultural irrigation in arid and hot climates where plant transpiration is high may affect plant accumulation of pharmaceutical and personal care products (PPCPs) and endocrine disrupting chemicals (EDCs). In this study, carrot, lettuce, and tomato plants were grown in solution containing 16 PPCP/EDCs in either a cool-humid or a warm-dry environment. Leaf bioconcentration factors (BCF) were positively correlated with transpiration for chemical groups of different ionized states (p < 0.05). However, root BCFs were correlated with transpiration only for neutral PPCP/EDCs (p < 0.05). Neutral and cationic PPCP/EDCs showed similar accumulation, while anionic PPCP/EDCs had significantly higher accumulation in roots and significantly lower accumulation in leaves (p < 0.05). Results show that plant transpiration may play a significant role in the uptake and translocation of PPCP/EDCs, which may have a pronounced effect in arid and hot climates where irrigation with treated wastewater is common. PMID:25594843

  5. Burn up calculations for the Iranian miniature reactor: A reliable and safe research reactor

    International Nuclear Information System (INIS)

    Faghihi, F.; Mirvakili, S.M.

    2009-01-01

    Presenting neutronic calculations pertaining to the Iranian miniature research reactor is the main goal of this article. This is a key to maintaining safe and reliable core operation. The following reactor core neutronic parameters were calculated: clean cold core excess reactivity (ρ ex ), control rod and shim worth, shut down margin (SDM), neutron flux distribution of the reactor core components, and reactivity feedback coefficients. Calculations for the fuel burnup and radionuclide inventory of the Iranian miniature neutron source reactor (MNSR), after 13 years of operational time, are carried out. Moreover, the amount of uranium burnup and produced plutonium, the concentrations and activities of the most important fission products, the actinide radionuclides accumulated, and the total radioactivity of the core are estimated. Flux distribution for both water and fuel temperature increases are calculated and changes of the central control rod position are investigated as well. Standard neutronic simulation codes WIMS-D4 and CITATION are employed for these studies. The input model was validated by the experimental data according to the final safety analysis report (FSAR) of the reactor. The total activity of the MNSR core is calculated including all radionuclides at the end of the core life and it is found to be equal to 1.3 x 10 3 Ci. Our investigation shows that the reactor is operating under safe and reliable conditions.

  6. Burn up calculations for the Iranian miniature reactor: A reliable and safe research reactor

    Energy Technology Data Exchange (ETDEWEB)

    Faghihi, F. [Department of Nuclear Engineering, School of Engineering, Shiraz University, Shiraz 71345 (Iran, Islamic Republic of); Research Center for Radiation Protection, Shiraz University, Shiraz (Iran, Islamic Republic of)], E-mail: faghihif@shirazu.ac.ir; Mirvakili, S.M. [Department of Nuclear Engineering, School of Engineering, Shiraz University, Shiraz 71345 (Iran, Islamic Republic of)

    2009-06-15

    Presenting neutronic calculations pertaining to the Iranian miniature research reactor is the main goal of this article. This is a key to maintaining safe and reliable core operation. The following reactor core neutronic parameters were calculated: clean cold core excess reactivity ({rho}{sub ex}), control rod and shim worth, shut down margin (SDM), neutron flux distribution of the reactor core components, and reactivity feedback coefficients. Calculations for the fuel burnup and radionuclide inventory of the Iranian miniature neutron source reactor (MNSR), after 13 years of operational time, are carried out. Moreover, the amount of uranium burnup and produced plutonium, the concentrations and activities of the most important fission products, the actinide radionuclides accumulated, and the total radioactivity of the core are estimated. Flux distribution for both water and fuel temperature increases are calculated and changes of the central control rod position are investigated as well. Standard neutronic simulation codes WIMS-D4 and CITATION are employed for these studies. The input model was validated by the experimental data according to the final safety analysis report (FSAR) of the reactor. The total activity of the MNSR core is calculated including all radionuclides at the end of the core life and it is found to be equal to 1.3 x 10{sup 3}Ci. Our investigation shows that the reactor is operating under safe and reliable conditions.

  7. Corrugated Membrane Nonlinear Deformation Process Calculation

    OpenAIRE

    A. S. Nikolaeva; S. A. Podkopaev

    2015-01-01

    Elastic elements are widely used in instrumentation. They are used to create a particular interference between the parts, for accumulating mechanical energy, as the motion transmission elements, elastic supports, and sensing elements of measuring devices. Device reliability and quality depend on the calculation accuracy of the elastic elements. A corrugated membrane is rather common embodiment of the elastic element.The corrugated membrane properties depend largely on its profile i.e. a gener...

  8. A Conceptual Model for Calculating the Return of Costs Invested in the Creation of an Economic Security Service, During a Short-Term Period

    Directory of Open Access Journals (Sweden)

    Melikhova Tetiana O.

    2018-02-01

    Full Text Available The article is aimed at suggesting methods for calculating the short-term period of return of costs invested in creation of an economic security service. The article considers approaches to calculation of the period of return of costs, advanced at the level of enterprise, which build the methodical basis for definition of such period. At the level of structural subdivisions of enterprise, which do not produce products, it is suggested to use conditional money flow as a source of financing advanced costs. The calculation of the short-term return on investment at the enterprise level provides for: allocation of expenses for the permanent and the replacement parts during the year; determination of the production of money flow and the money flow accumulated during the year. Annual depreciation payments are the basis of fixed costs. Methods of determination of the gross, net, valid, and specified periods of return of costs, advanced during the year for introduction of an economic security service at enterprise, have been suggested.

  9. Fission product releases at severe LWR accident conditions: ORNL/CEA measurements versus calculations

    Energy Technology Data Exchange (ETDEWEB)

    Andre, B.; Ducros, G.; Leveque, J.P. [CEA Centre d`Etudes de Grenoble, 38 (France). Dept. de Thermohydraulique et de Physique; Osborne, M.F.; Lorenz, R.A. [Oak Ridge National Lab., TN (United States); Maro, D. [CEA Centre d`Etudes de Fontenay-aux-Roses, 92 (France). Dept. de Protection de l`Environnement et des Installations

    1995-12-31

    Experimental programs in the United States and France have followed similar paths in supplying much of the data needed to analyze severe accidents. Both the HI/VI program, conducted at the Oak Ridge National Laboratory (ORNL) under the sponsorship of the U. S. Nuclear Regulatory Commission (NRC), and the HEVA/VERCORS program, supported by IPSN-Commissariat a l`Energie Atomique (CEA) and carried out at the Centre d`Etudes Nucleaires de Grenoble, have studied fission product release from light water reactor (LWR) fuel samples during test sequences representative of severe accidents. Recognizing that more accurate data, i.e., a better defined source term, could reduce the safety margins included in the rather conservative source terms originating from WASH-1400, the primary objective of these programs has been to improve the data base concerning fission product release and behavior at high temperatures. To facilitate the comparison, a model based on fission product diffusion mechanisms that was developed at ORNL and adapted with CEA experimental data is proposed. This CEA model is compared with the ORNL experimental data in a blind test. The two experimental programs used similar techniques in out-of-pile studies. Highly irradiated fuel samples were heated in radiofrequency induction furnaces to very high temperatures (up to 2700 K at ORNL and 2750 K at CEA) in oxidizing (H{sub 2}O), reducing (H{sub 2}) or mixed (H{sub 2}O+H{sub 2}) environments. The experimental parameters, which were chosen from calculated accident scenarios, did not duplicate specific accidents, but rather emphasized careful control of test conditions to facilitate extrapolation of the results to a wide variety of accident situations. This paper presents a broad and consistent database from ORNL and CEA release results obtained independently since the early 1980`S. A comparison of CORSOR and CORSOR Booth calculations, currently used in safety analysis, and the experimental results is presented and

  10. Variability of oil and gas well productivities for continuous (unconventional) petroleum accumulations

    Science.gov (United States)

    Charpentier, Ronald R.; Cook, Troy A.

    2013-01-01

    can also be done by vertical versus horizontal wells, by length of horizontal completion, by distance to closest previously drilled well, by thickness of reservoir interval, or by any other variable for which one has or can calculate values for each well. The resulting plots show how one can subdivide the total range of productivity in shale-gas wells into smaller subsets that are more appropriate for use as analogs.

  11. Willow wood production on radionuclide polluted areas

    Directory of Open Access Journals (Sweden)

    Rodkin Oleg I.

    2010-01-01

    Full Text Available ABSTRACT: One of the key environmental problems in Belarus is effective use of agricultural lands contaminated by radionuclide due to the Chernobyl disaster. The alternative method to traditional agricultural crops is fast growing willow cultivation. It is possible to use biomass of willow as renewable energy source. The goal of our investigation was the estimation of environmental aspects of willow wood production on polluted areas. The field study experiments (2007-2010 were conducted at Krichev district of Mogilev region in eastern Belarus. This region characterized by high level of Cs-137 contamination as well as high level of heavy metals pollution. In the first stage of experiments, the concentration of cesium-137 in different parts of willow biomass had been measured and transfer factor calculated. The measuring had been done for leaves, roots, and wood. To control cesium-137 accumulation in willow biomass we apply different types (nitrogen N, phosphorus P and potassium K and dose of fertilizer. The experiments show that potassium mineral fertilizer is the key factor for radionuclide accumulation control. The optimal dose of potassium is 90 kg per hectare. On the base of experimental results the model of cesium-137 accumulation in the wood for a 21 year has been developed. In accordance with calculation to the end of willow cultivation (21 year concentration of cesium-137 in wood will not be higher than permitted even with the level of cesium-137 contamination in the soil 1480 kBq/m2 (maximum 140 kqB/m2 with permitted level for firewood is 740 Bq/kg.. The concentration of cesium-137 in the roots increases gradually and get maximum in 21 year (3000 kqB/m2. Our results confirm that in the sum about 0.8 million hectares of radionuclide polluted arable lands partly excluded from agricultural practice in Belarus could be used for willow biomass production.

  12. Effect of greenhouse vegetable farming duration on Zinc accumulation in Northeast China

    Science.gov (United States)

    Wang, Jun; Yu, Peiying; Cui, Shuang; Chen, Xin; Shi, Yi

    2018-02-01

    Greenhouse vegetable production (GVP) has rapidly expanded, and reqiures more attention due to its heavy metal contamination. In this study, different cultivation greenhouses of 1, 2, 3, 5 and 13 years were selected to investigate the effects of GVP duration on Zn accumulation. The results revealed high Zn (total Zn and available Zn) accumulation in GVP surface layers (0-20 cm), and Zn contents in 0-20 cm soil layers were positively correlated with GVP duration (P<0.01). Zn accumulation was mainly attributed to manure fertilizer application due to higher concentrations of Zn in manures. For greenhouse sustainability, reduction of manure application and reasonable use of passivation materials may alleviate metal phytoavailability and the health risk.

  13. Capability of Catfish (Clarias gariepinus to Accumulate Hg2+ From Water

    Directory of Open Access Journals (Sweden)

    Heny Suseno

    2015-12-01

    Full Text Available Mercury is hazardous contaminant that can be accumulated by aquatic organisms such as fishes, mussels etc. Catfish is one of source of animal protein but it also can accumulate Hg2+ from water that used in aquaculture. Due to less information about capability of catfish to accumulate Hg2+, therefore we studied bioaccumulation of Hg2+ that used biokinetic approach (aqueous uptake-rate, and elimination-rate.  Nuclear application technique was applied in this study by using radiotracer of 203Hg.  A simple kinetic model was then constructed to predict the bioaccumulation capability of   by catfish. The result of experiments were shown that the uptake rate of difference Hg2+ concentration were 79.90 to 101.22 ml.g-1.d-1. Strong correlation between uptake rates with increasing Hg2+concentration. In addition, the elimination rates were range 0.080 – 0.081 day-1. The biology half time (t1/2b of Hg2+ in whole body catfish were 8.50 – 8.63 days.  However, no clear correlation  between elimination rate with increasing concentration of Hg2+. The calculation of Bio Concentration Factor (BCF shown catfish have capability to accumulated Hg maximum 1242.69 time than its concentration in water

  14. Seasonal changes of metal accumulation and distribution in common club rush (Schoenoplectus lacustris) and common reed (Phragmites australis).

    Science.gov (United States)

    Duman, Fatih; Cicek, Mehmet; Sezen, Goksal

    2007-08-01

    In this study, two aquatic macrophytes Phragmites australis and Schoenoplectus lacustris and corresponding sediment samples were collected every three months from Lake Sapanca (Turkey) and analysed for their heavy-metal contents (Pb, Cr, Cu, Mn, Ni, Zn and Cd). Accumulation factor ratios of plant parts were calculated for all metals, and the two species were compared in terms of accumulation properties. The highest concentrations were measured in the root systems while relatively low concentrations were found in the rhizome and above-ground parts of the plants. The accumulation ratios of root for P. australis were usually higher than the ratios for S. lacustris. While the accumulation ratios of root were higher in winter than in the other seasons for P. australis, for S. lacustris the highest accumulation ratios were found in the autumn. Both plant species were found to be root accumulators of Pb, Cu, Mn, Ni, Zn and Cd.

  15. Uptake and accumulation of four PPCP/EDCs in two leafy vegetables

    International Nuclear Information System (INIS)

    Dodgen, L.K.; Li, J.; Parker, D.; Gan, J.J.

    2013-01-01

    Many pharmaceutical and personal care products (PPCPs) and endocrine-disrupting chemicals (EDCs) are present in reclaimed water, leading to concerns of human health risks from the consumption of food crops irrigated with reclaimed water. This study evaluated the potential for plant uptake and accumulation of four commonly occurring PPCP/EDCs, i.e., bisphenol A (BPA), diclofenac sodium (DCL), naproxen (NPX), and 4-nonylphenol (NP), by lettuce (Lactuca sativa) and collards (Brassica oleracea) in hydroponic culture, using 14 C-labeled compounds. In both plant species, plant accumulation followed the order of BPA > NP > DCL > NPX and accumulation in roots was much greater than in leaves and stems. Concentrations of 14 C-PPCP/EDCs in plant tissues ranged from 0.22 ± 0.03 to 927 ± 213 ng/g, but nearly all 14 C-residue was non-extractable. PPCP/EDCs, particularly BPA and NP, were also extensively transformed in the nutrient solution. Dietary uptake of these PPCP/EDCs by humans was predicted to be negligible. -- Highlights: •Accumulation of bisphenol A, diclofenac, naproxen, and 4-nonylphenol by lettuce and collards was examined. •Plant accumulation had the order of BPA > NP > DCL > NPX. •Accumulation in roots was greater than in new leaves, original leaves, and stems. •Nearly all accumulated analyte was non-extractable. -- Four commonly occurring PPCP/EDCs were taken up into roots of lettuce and collards, but translocation into edible leaves was limited and nearly all residue was non-extractable

  16. Accumulation Systems of Electric Energy Solved by Multicriteria Analysis Methods IPA and Topsis

    Directory of Open Access Journals (Sweden)

    Zdenek Hradilek

    2008-01-01

    Full Text Available This work deals with utilization of multicriteria analysis methods IPA and TOPSIS to assess three storage systems (Fuel Cells, Lead Acid Batteries and Pumped Storage Hydro Plants. Procedures of IPA and TOPSIS methods are described here as like as calculation of mentioned problem. Storage systems are assessed in terms of four criteria (Start up Time, Efficiency of Accumulation, Lifetime and Specific Costs/ kW of Power Output. Weights of criteria are also focused here. They are suggested by experts and statistically calculated.

  17. Calculation of displacement, gas, and transmutation production in stainless steel irradiated with spallation neutrons

    International Nuclear Information System (INIS)

    Wechsler, M.A.; Ramavarapu, R.; Daugherty, E.L.; Palmer, R.C.; Bullen, D.B.; Sommer, W.F.

    1993-01-01

    Calculations using the high-energy transport code LAHET have been made for the production of displacements, helium gas, and transmuted atoms for stainless steel (Fe-18 wt % Cr-10 wt % Ni) irradiated with spallation neutrons at energies of 100 to 1600 MeV. The damage energy cross section increased from about 250 to 350 b keV for increasing neutron energies from 100 to 1600 MeV with a spallation spectrum average of 281 barns-keV. For a displacement threshold energy of 33 eV, the corresponding spectrum-average displacement cross section is 3400 barns. The PKA spectrum was found to be fairly independent of the incident neutron energy, with an average damage energy of 0.25--0.30 MeV. The helium production cross section increased monotonically with increasing neutron energy, with a spectrum average of 0.32 barns. The maximum transmutation yield was observed near manganese (Z = 25), corresponding to a production cross section of about 0.2 barns. Relevance to fusion materials is discussed

  18. Diallel analysis for aflatoxin accumulation and fall armyworm leaf feeding damage in maize

    Science.gov (United States)

    Two of the major impediments to profitable maize, Zea mays L., production in the southern United States are losses from feeding by fall armyworm, Spodoptera frugiperda (J.E. Smith), and losses from the production and accumulation of aflatoxin in maize grain. The fall armyworm feeds on all above-grou...

  19. Operateurs et engins de calcul en virgule flottante et leur application a la simulation en temps reel sur FPGA

    Science.gov (United States)

    Ould Bachir, Tarek

    The real-time simulation of electrical networks gained a vivid industrial interest during recent years, motivated by the substantial development cost reduction that such a prototyping approach can offer. Real-time simulation allows the progressive inclusion of real hardware during its development, allowing its testing under realistic conditions. However, CPU-based simulations suffer from certain limitations such as the difficulty to reach time-steps of a few microsecond, an important challenge brought by modern power converters. Hence, industrial practitioners adopted the FPGA as a platform of choice for the implementation of calculation engines dedicated to the rapid real-time simulation of electrical networks. The reconfigurable technology broke the 5 kHz switching frequency barrier that is characteristic of CPU-based simulations. Moreover, FPGA-based real-time simulation offers many advantages, including the reduced latency of the simulation loop that is obtained thanks to a direct access to sensors and actuators. The fixed-point format is paradigmatic to FPGA-based digital signal processing. However, the format imposes a time penalty in the development process since the designer has to asses the required precision for all model variables. This fact brought an import research effort on the use of the floating-point format for the simulation of electrical networks. One of the main challenges in the use of the floating-point format are the long latencies required by the elementary arithmetic operators, particularly when an adder is used as an accumulator, an important building bloc for the implementation of integration rules such as the trapezoidal method. Hence, single-cycle floating-point accumulation forms the core of this research work. Our results help building such operators as accumulators, multiply-accumulators (MACs), and dot-product (DP) operators. These operators play a key role in the implementation of the proposed calculation engines. Therefore, this

  20. Chemopreventive glucosinolate accumulation in various broccoli and collard tissues: Microfluidic-based targeted transcriptomics for by-product valorization.

    Science.gov (United States)

    Lee, Young-Sang; Ku, Kang-Mo; Becker, Talon M; Juvik, John A

    2017-01-01

    Floret, leaf, and root tissues were harvested from broccoli and collard cultivars and extracted to determine their glucosinolate and hydrolysis product profiles using high performance liquid chromatography and gas chromotography. Quinone reductase inducing bioactivity, an estimate of anti-cancer chemopreventive potential, of the extracts was measured using a hepa1c1c7 murine cell line. Extracts from root tissues were significantly different from other tissues and contained high levels of gluconasturtiin and glucoerucin. Targeted gene expression analysis on glucosinolate biosynthesis revealed that broccoli root tissue has elevated gene expression of AOP2 and low expression of FMOGS-OX homologs, essentially the opposite of what was observed in broccoli florets, which accumulated high levels of glucoraphanin. Broccoli floret tissue has significantly higher nitrile formation (%) and epithionitrile specifier protein gene expression than other tissues. This study provides basic information of the glucosinolate metabolome and transcriptome for various tissues of Brassica oleracea that maybe utilized as potential byproducts for the nutraceutical market.

  1. Study of Cycling Air-Cooling System with a Cold Accumulator for Micro Gas-Turbine Installations

    Science.gov (United States)

    Ochkov, V. F.; Stepanova, T. A.; Katenev, G. M.; Tumanovskii, V. A.; Borisova, P. N.

    2018-05-01

    Using the cycling air-cooling systems of the CTIC type (Combustion Turbine Inlet Cooling) with a cold accumulator in a micro gas-turbine installation (micro-GTI) to preserve its capacity under the seasonal temperature rise of outside air is described. Water ice is used as the body-storage in the accumulators, and ice water (water at 0.5-1.0°C) is used as the body that cools air. The ice water circulates between the accumulator and the air-water heat exchanger. The cold accumulator model with renewable ice resources is considered. The model contains the heat-exchanging tube lattice-evaporator covered with ice. The lattice is cross-flowed with water. The criterion heat exchange equation that describes the process in the cold accumulator under consideration is presented. The calculations of duration of its active operation were performed. The dependence of cold accumulator service life on water circulation rate was evaluated. The adequacy of the design model was confirmed experimentally in the mock-up of the cold accumulator with a refrigerating machine periodically creating a 200 kg ice reserve in the reservoir-storage. The design model makes it possible to determine the weight of ice reserve of the discharged cold accumulator for cooling the cycle air in the operation of a C-30 type micro- GTI produced by the Capstone Company or micro-GTIs of other capacities. Recommendations for increasing the working capacity of cold accumulators of CTIC-systems of a micro-GTI were made.

  2. Electrochemical accumulators batteries; Accumulateurs electrochimiques batteries

    Energy Technology Data Exchange (ETDEWEB)

    Ansart, F; Castillo, S; Laberty- Robert, C; Pellizon-Birelli, M [Universite Paul Sabatier, Lab. de Chimie des Materiaux Inorganiques et Energetiques, CIRIMAT, UMR CNRS 5085, 31 - Toulouse (France); and others

    2000-07-01

    It is necessary to storage the electric power in batteries to join the production and the utilization. In this domain progresses are done every days in the technics and also in the available materials. These technical days present the state of the art in this domain. Many papers were presented during these two days giving the research programs and recent results on the following subjects: the lithium batteries, the electrolytes performances and behaviour, lead accumulators, economic analysis of the electrochemical storage market, the batteries applied to the transportation sector and the telephones. (A.L.B.)

  3. Atomic physics and synchrotron radiation: The production and accumulation of highly charged ions

    International Nuclear Information System (INIS)

    Johnson, B.M.; Meron, M.; Agagu, A.; Jones, K.W.

    1986-01-01

    Synchrotron radiation can be used to produce highly-charged ions, and to study photoexcitation and photoionization for ions of virtually any element in the periodic table. To date, with few exceptions, atomic physics studies have been limited to rare gases and a few metal vapors, and to photoexcitation energies in the VUV region of the electromagnetic spectrum. These limitations can now be overcome using photons produced by high-brightness synchrotron storage rings, such as the x-ray ring at the National Synchrotron Light Source (NSLS) at Brookhaven. Furthermore, calculations indicate that irradiation of an ion trap with an intense energetic photon beam will result in a viable source of highly-charged ions that can be given the name PHOBIS: the PHOton Beam Ion Source. Promising results, which encourage the wider systematic use of synchrotron radiation in atomic physics research, have been obtained in recent experiments on VUV photoemission and the production and storage of multiply-charged ions. 26 refs., 4 figs., 1 tab

  4. Beam accumulation with the SIS electron cooler

    International Nuclear Information System (INIS)

    Steck, M.; Groening, L.; Blasche, K.; Franczak, B.; Franzke, B.; Winkler, T.; Parkhomchuk, V.V.

    2000-01-01

    An electron cooling system has started operation in the heavy ion synchrotron SIS which is used to increase the intensity for highly charged ions. Fast transverse cooling of the hot ion beam after horizontal multiturn injection allows beam accumulation at the injection energy. After optimization of the accumulation process an intensity increase in a synchrotron pulse by more than one order of magnitude has been achieved. For highly charged ions the maximum number of particles has been increased from 1x10 8 to 1x10 9 . For lighter ions intensity limitations have been encountered which are caused by the high phase space density of the cooled ion beam. Momentum spreads in the 10 -4 range and emittances well below 10 π mm mrad have been demonstrated. Recombination losses both in the residual gas and with the free cooler electrons determine the maximum intensity for highly charged ions. Systematic measurements of the recombination rates have been performed providing data for an optimum choice of the charge state. Strong enhancement of the recombination rate with free electrons compared to theoretical calculations of radiative electron capture have been observed

  5. Comparison of different eigensolvers for calculating vibrational spectra using low-rank, sum-of-product basis functions

    Science.gov (United States)

    Leclerc, Arnaud; Thomas, Phillip S.; Carrington, Tucker

    2017-08-01

    Vibrational spectra and wavefunctions of polyatomic molecules can be calculated at low memory cost using low-rank sum-of-product (SOP) decompositions to represent basis functions generated using an iterative eigensolver. Using a SOP tensor format does not determine the iterative eigensolver. The choice of the interative eigensolver is limited by the need to restrict the rank of the SOP basis functions at every stage of the calculation. We have adapted, implemented and compared different reduced-rank algorithms based on standard iterative methods (block-Davidson algorithm, Chebyshev iteration) to calculate vibrational energy levels and wavefunctions of the 12-dimensional acetonitrile molecule. The effect of using low-rank SOP basis functions on the different methods is analysed and the numerical results are compared with those obtained with the reduced rank block power method. Relative merits of the different algorithms are presented, showing that the advantage of using a more sophisticated method, although mitigated by the use of reduced-rank SOP functions, is noticeable in terms of CPU time.

  6. Batteries and accumulators in France

    International Nuclear Information System (INIS)

    2012-12-01

    The present report gives an overview of the batteries and accumulators market in France in 2011 based on the data reported through ADEME's Register of Batteries and accumulators. In 2001, the French Environmental Agency, known as ADEME, implemented a follow-up of the batteries and accumulators market, creating the Observatory of batteries and accumulators (B and A). In 2010, ADEME created the National Register of producers of Batteries and Accumulators in the context of the implementation of the order issued on November 18, 2009. This is one of the four enforcement orders for the decree 2009-1139 issued on September 22, 2009, concerning batteries and accumulators put on the market and the disposal of waste batteries and accumulators, and which transposes the EU-Directive 2006/66/CE into French law. This Register follows the former Observatory for batteries and accumulators. This Register aims to record the producers on French territory and to collect the B and A producers and recycling companies' annual reporting: the regulation indeed requires that all B and A producers and recycling companies report annually on the Register the quantities of batteries and accumulators they put on the market, collect and treat. Based on this data analysis, ADEME issues an annual report allowing both the follow-up of the batteries and accumulators market in France and communication regarding the achievement of the collection and recovery objectives set by EU regulation. This booklet presents the situation in France in 2011

  7. Observation of Nitrogen and Phosphorus Removals and Accumulations in Surface Flow Constructed Wetland (SFCW

    Directory of Open Access Journals (Sweden)

    Suntud Sirianuntapiboon

    2012-06-01

    Full Text Available The tropical emergent plant species; Cyperus involucratus, Canna siamensis, Heliconia sp., Hymenocallis littoralis, Typha augustifolia and Thalia dealbata were used to observe nutrients (total phosphorus: TP and total nitrogen: TN removal efficiencies of surface flow constructed wetland (SFCW. The system was operated at different hydraulic retention time (HRT of 1, 3 and 5 days and the average atmospheric temperature of 29.1 ± 4.9oC. The seafood industrial wastewater was employed as the influent. The high biomass production plant species; Cyperus involucratus, Typha augustifolia and Thalia dealbata could generate the high oxidative environment. Amount of N and P accumulations in plant tissue were increased with the increase of plant biomass production. The system did not show any significantly different on N and P accumulations among the tested-emergent plant species. But the amount of accumulated-N and P were increased with the increase of HRT. N accumulations in plant tissue, effluent, sediment and media of the system with the tested-emergent plant species under HRT of 1-5 days were in the range of 2.17-43.80%, 7.91-27.75%, 19.62-36.86% and 14.39-31.88%, respectively. Also, P accumulations were 0.79-17.01%, 20.35-28.37%, 40.96-56.27% and 9.09-20.47%, respectively.

  8. [Capital accumulation patterns: capital and services in the current transformations of the health system].

    Science.gov (United States)

    de Andreazzi, Maria de Fátima Siliansky; Kornis, George Edward Machado

    2008-01-01

    The purpose of this article is to introduce elements of the capitalist society economic reproduction to the discussion around the current dynamics of health accumulation. It identifies the direction and significance of capital accumulation in the health area as well as the characteristics of the economic environment where the competition currently takes place. The hypothetic hypertrophy of the financial sphere is seen as a means for structuring the capitalist economy since the late twentieth century. The former delimitations between industrial production and service delivery are blurred and weakened; the competition process shows new features and the contradictions - internally between the different elements of the health industry and externally with other sectors - are changing. This article aggregates elements for a contemporary analysis of the "medical-industrial complex" on the basis of a theoretical-historical-conceptual approach. We identify changes in the capital dynamics of this complex at international and national level and stress the increasing role of the health services as a forefront of capital accumulation. The new approach is based on the economic thinking of Marx in addition to the current discussions about the theory of financial capital accumulation and the new productive configurations of the large corporations.

  9. Effect of Thai banana (Musa AA group) in reducing accumulation of oxidation end products in UVB-irradiated mouse skin.

    Science.gov (United States)

    Leerach, Nontaphat; Yakaew, Swanya; Phimnuan, Preeyawass; Soimee, Wichuda; Nakyai, Wongnapa; Luangbudnark, Witoo; Viyoch, Jarupa

    2017-03-01

    Chronic UVB exposure causes skin disorders and cancer through DNA strand breaks and oxidation of numerous functional groups of proteins and lipids in the skin. In this study, we investigated the effects of Thai banana (Musa AA group, "Khai," and Musa ABB group, "Namwa") on the prevention of UVB-induced skin damage when fed to male ICR mice. Mice were orally fed banana (Khai or Namwa) fruit pulps at dose of 1mg/g body weight/day for 12weeks. The shaved backs of the mice were irradiated with UVB for 12weeks. The intensity dose of UVB-exposure was increased from 54mJ/cm 2 /exposure at week 1 to 126mJ/cm 2 /exposure at week 12. A significant increase in skin thickness, lipid peroxidation, protein oxidation end products, and expression of MMP-1 was observed in UVB-irradiated mouse skin. A reduction in the accumulation of oxidation end products was found in the skin of UVB-irradiated mice receiving Khai. This occurred in conjunction with a reduction in MMP-1 expression, inhibition of epidermal thickening, and induction of γ-GCS expression. The dietary intake of Khai prevented skin damage from chronic UVB exposure by increased γ-GCS expression and reduced oxidation end products included carbonyls, malondialdehyde and 4-hydroxynonenal. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. HETC-3STEP calculations of proton induced nuclide production cross sections at incident energies between 20 MeV and 5 GeV

    International Nuclear Information System (INIS)

    Takada, Hiroshi; Yoshizawa, Nobuaki; Ishibashi, Kenji.

    1996-08-01

    For the OECD/NEA code intercomparison, nuclide production cross sections of 16 O, 27 Al, nat Fe, 59 Co, nat Zr and 197 Au for the proton incidence with energies of 20 MeV to 5 GeV are calculated with the HETC-3STEP code based on the intranuclear cascade evaporation model including the preequilibrium and high energy fission processes. In the code, the level density parameter derived by Ignatyuk, the atomic mass table of Audi and Wapstra and the mass formula derived by Tachibana et al. are newly employed in the evaporation calculation part. The calculated results are compared with the experimental ones. It is confirmed that HETC-3STEP reproduces the production of the nuclides having the mass number close to that of the target nucleus with an accuracy of a factor of two to three at incident proton energies above 100 MeV for nat Zr and 197 Au. However, the HETC-3STEP code has poor accuracy on the nuclide production at low incident energies and the light nuclide production through the fragmentation process induced by protons with energies above hundreds of MeV. Therefore, further improvement is required. (author)

  11. Estimation of erosion-accumulative processes at the Inia River's mouth near high-rise construction zones.

    Science.gov (United States)

    Sineeva, Natalya

    2018-03-01

    Our study relevance is due to the increasing man-made impact on water bodies and associated land resources within the urban areas, as a consequence, by a change in the morphology and dynamics of Rivers' canals. This leads to the need to predict the development of erosion-accumulation processes, especially within the built-up urban areas. Purpose of the study is to develop programs on the assessment of erosion-accumulation processes at a water body, a mouth area of the Inia River, in the of perspective high-rise construction zone of a residential microdistrict, the place, where floodplain-channel complex is intensively expected to develop. Results of the study: Within the velocities of the water flow comparing, full-scale measured conditions, and calculated from the model, a slight discrepancy was recorded. This allows us to say that the numerical model reliably describes the physical processes developing in the River. The carried out calculations to assess the direction and intensity of the channel re-formations, made us possible to conclude, there was an insignificant predominance of erosion processes over the accumulative ones on the undeveloped part of the Inia River (the processes activity is noticeable only in certain areas (by the coasts and the island)). Importance of the study: The study on the erosion-accumulation processes evaluation can be used in design decisions for the future high-rise construction of this territory, which will increase their economic efficiency.

  12. Free cholesterol accumulation impairs antioxidant activities and aggravates apoptotic cell death in menadione-induced oxidative injury.

    Science.gov (United States)

    Lee, Waisin; Xu, Mingjing; Li, Yue; Gu, Yong; Chen, Jianping; Wong, Derek; Fung, Peter C W; Shen, Jiangang

    2011-10-01

    Although the relationship between hypercholesterolemia and oxidative stress has been extensively investigated, direct evidence regarding to the roles of cholesterol accumulation in the generations of reactive oxygen species (ROS) and apoptotic cell death under oxidative stress is lack. In this study, we investigated productions of superoxide anions (O(2)(-)) and nitric oxide (NO), and apoptotic cell death in wild type Chinese hamster ovary (CHO) cells and cholesterol accumulated CHO cells genetically and chemically. Oxidative stress was induced by menadione challenge. The results revealed that abundance of free cholesterol (FC) promoted menadione-induced O(2)(-) and NO productions. FC accumulation down-regulated eNOS expression but up-regulated NADPH oxidases, and inhibited the activities of superoxide dismutase (SOD) and catalase. Treatment of menadione increased the expressions of iNOS and qp91 phox, enhanced the activities of SOD and catalase in the wild-type CHO cells but inhibited the activity of glutathione peroxidase in the cholesterol accumulated CHO cells. Moreover, FC abundance promoted apoptotic cell death in these cells. Taken together, those results suggest that free cholesterol accumulation aggravates menadione-induced oxidative stress and exacerbates apoptotic cell death. Copyright © 2011 Elsevier Inc. All rights reserved.

  13. Aqueous photodegradation of 4-tert-butylphenol: By-products, degradation pathway and theoretical calculation assessment

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Yanlin [State Key Laboratory of Pollution Control and Resources Reuse, College of Environmental Science and Engineering, Tongji University, Shanghai 200092 (China); Shi, Jin; Chen, Hongche [Shanghai Key Laboratory of Atmospheric Particle Pollution and Prevention, Department of Environmental Science & Engineering, Fudan University, Shanghai 200433 (China); Zhao, Jianfu [State Key Laboratory of Pollution Control and Resources Reuse, College of Environmental Science and Engineering, Tongji University, Shanghai 200092 (China); Dong, Wenbo, E-mail: wbdong@fudan.edu.cn [Shanghai Key Laboratory of Atmospheric Particle Pollution and Prevention, Department of Environmental Science & Engineering, Fudan University, Shanghai 200433 (China)

    2016-10-01

    4-tert-butylphenol (4-t-BP), an endocrine disrupting chemical, is widely distributed in natural bodies of water but is difficult to biodegrade. In this study, we focused on the transformation of 4-t-BP in photo-initiated degradation processes. The steady-state photolysis and laser flash photolysis (LFP) experiments were conducted in order to elucidate its degradation mechanism. Identification of products was performed using the GC–MS, LC-MS and theoretical calculation techniques. The oxidation pathway of 4-t-BP by hydroxyl radical (HO·) was also studied and H{sub 2}O{sub 2} was added to produce HO·. 4-tert-butylcatechol and 4-tert-butylphenol dimer were produced in 4-t-BP direct photolysis. 4-tert-butylcatechol and hydroquinone were produced by the oxidation of HO·. But the formation mechanism of 4-tert-butylcatechol in the two processes was different. The benzene ring was fractured in 4-t-BP oxidation process and 29% of TOC was degraded after 16 h irradiation. - Highlights: • Photodegradation of 4-t-BP, an endocrine disrupting chemical, has been investigated. • 3 stable byproducts were identified from photolysis and oxidation processes. • 5 transient by-products were concluded from LFP experiments. • The theoretical calculation was performed to confirm the byproducts. • 4-t-BP was degraded with increasing efficiency: 254 nm < H{sub 2}O{sub 2}/313 nm < H{sub 2}O{sub 2}/254 nm.

  14. SCREENING OF CONTENT AND DYNAMIC OF ACCUMULATION OF POLYPHENOLS IN SOME BASIDIOMYCETES SPECIES

    Directory of Open Access Journals (Sweden)

    Veligodska A. K.

    2015-12-01

    Full Text Available The aim of the study was to investigate the total content of polyphenolic substances in Basidiomycetes carpophores from 50 species, of which 27 belong to the order Polyporales and 23 to the order Agaricales. Introduced 23 strains of 8 species of Basidiomycetes. Methods. Gathered wild carpophores dried and crushed to a particle size of 0,1 till 0,01 mm and searching strains were cultured in Erlenmeyyers flasks by surface method on standard glucose-peptone culture medium. Determination of total content of polyphenolic compounds was carried out in ethanol extracts of mycological material by a modified method of Folin-Chokalteu. Completely dry biomass of carpophores and mycelium was determined gravimetrically. Results. There was identified the species of polyporal fungi Ganoderma applanatum, Ganoderma lucidum, Laetiporus sulphureus and Fomes fomentarius and types of agarical mushrooms Stropharia rugosoannulata, Agrocybe cylindracea, Tricholoma flavovirens, Flammulina velutipes, Pleurotus ostreatus and Fistulina hepatica high in polyphenolic compounds. It was determined the content of polyphenols ranging from more than 60 mg / g completely dry biomass. For introduced strains established dynamics of growth and accumulation of polyphenolic compounds in the mycelium and culture filtrate during fermentation on glucose-peptone medium. All cultures reach a maximum accumulation of biomass on the 12th day of growth. Shizophyllum commune Sc-1101 and 10 and F. velutipes F-202 have been identified as the most productive strains. The lowest accumulation of absolutely dry biomass was recorded for strain P. ostreatus P-192 and strain F. fomentarius Ff-09. Cultures have investigated individual value growth such as biomass accumulation in the applied cultivation conditions, which probably reflects the suitability of the medium for their growth and genotypic characteristics. Strains are overwhelmingly able to accumulate polyphenolic compounds in both mycelium and

  15. SCREENING OF CONTENT AND DYNAMIC OF ACCUMULATION OF POLYPHENOLS IN SOME BASIDIOMYCETES SPECIES

    Directory of Open Access Journals (Sweden)

    A. K. Veligodska

    2015-11-01

    Full Text Available The aim of the study was to investigate the total content of polyphenolic substances in Basidiomycetes carpophores from 50 species, of which 27 belong to the order Polyporales and 23 to the order Agaricales. Introduced 23 strains of 8 species of Basidiomycetes. Methods. Gathered wild carpophores dried and crushed to a particle size of 0,1 till 0,01 mm and searching strains were cultured in Erlenmeyyers flasks by surface method on standard glucose-peptone culture medium. Determination of total content of polyphenolic compounds was carried out in ethanol extracts of mycological material by a modified method of Folin-Chokalteu. Completely dry biomass of carpophores and mycelium was determined gravimetrically. Results. There was identified the species of polyporal fungi Ganoderma applanatum, Ganoderma lucidum, Laetiporus sulphureus and Fomes fomentarius and types of agarical mushrooms Stropharia rugosoannulata, Agrocybe cylindracea, Tricholoma flavovirens, Flammulina velutipes, Pleurotus ostreatus and Fistulina hepatica high in polyphenolic compounds. It was determined the content of polyphenols ranging from more than 60 mg / g completely dry biomass. For introduced strains established dynamics of growth and accumulation of polyphenolic compounds in the mycelium and culture filtrate during fermentation on glucose-peptone medium. All cultures reach a maximum accumulation of biomass on the 12th day of growth. Shizophyllum commune Sc-1101 and 10 and F. velutipes F-202 have been identified as the most productive strains. The lowest accumulation of absolutely dry biomass was recorded for strain P. ostreatus P-192 and strain F. fomentarius Ff-09. Cultures have investigated individual value growth such as biomass accumulation in the applied cultivation conditions, which probably reflects the suitability of the medium for their growth and genotypic characteristics. Strains are overwhelmingly able to accumulate polyphenolic compounds in both mycelium and

  16. Validation of FLUKA calculated cross-sections for radioisotope production in proton-on-target collisions at proton energies around 1 GeV

    CERN Document Server

    Felcini, M

    2006-01-01

    The production cross-sections of several radioisotopes induced by 1 GeV protons impinging on different target materials have been calculated using the FLUKA Monte Carlo and compared to measured cross-sections. The emphasis of this study is on the production of alpha and beta/gamma emitters of interest for activation evaluations at a research complex, such as the EURISOL complex, using several MW power proton driver at an energy of 1 GeV. The comparisons show that in most of the cases of interest for such evaluations, the FLUKA Monte Carlo reproduces radioisotope production cross-sections within less than a factor of two with respect to the measured values. This result implies that the FLUKA calculations are adequately accurate for proton induced activation estimates at a 1 GeV high power proton driver complex.

  17. The effect of natural antioxidants on the rate of accumulation of oxidation products in the fat phase of butter cream

    Directory of Open Access Journals (Sweden)

    M. S. Voronina

    2016-01-01

    Full Text Available Describes the main finishing prefabricated pastries and cakes-cream. Researched range of cream depending on the fruit components and method of production. Aim: to study the degree of oxidation cream with natural antioxidants from fruits and berries processing products, namely in the form of concentrated juice of fruits and berries. Outlines the process of oxidation of lipids, one of the fundamental processes of loss of quality food products. Describes the action of antioxidants as antioxidants on accumulation intensity concentrations of primary and secondary oxidation products, making the final product unsuitable for the consumer and the bounding its shelf life. Presents the results of a study of the contents of primary and secondary oxidation products in butter cream immediately after cooking, as well as samples, stored for five days with the addition of antioxidants in the form of concentrated juice of fruits and berries in the amount of 2–7% by weight of cream. As a control sample has been used cream with no additives. Quality indicators to characterize the degree of oxidation of the product: acid, peroxide, anizidin and tioburbit number. The study found that adding a concentrated juice of fruits and berries as antioxidant in recipe cream reduces the growth rate of the concentration of free fatty acids on the fifth day, as compared with the reference sample. Adding concentrated juice of fruits and berries slows down the process of dissolution of the fat molecules in fat fraction of cream with the formation of free fatty acids; intensity decay reaction of peroxides and hydroxides slows down and, consequently, decreases the formation of aldehydes, deteriorating the taste and smell of the cream; quantitatively reduced the growth of education malondial′degida.

  18. Multiplying Forest Garden Systems with biochar based organic fertilization for high carbon accumulation, improved water storage, nutrient cycling, and increased food diversity and farm productivity

    Science.gov (United States)

    Schmidt, Hans-Peter; Pandit, Bishnu Hari; Lucht, Wolfgang; Gerten, Dieter; Kammann, Claudia

    2017-04-01

    10 years). Besides covering the set-up costs, farmers received and continue to receive carbon payments for each survived tree during the first three years. Based on a voluntary carbon credit price of 35 USD per t CO2, the annual income of the farmers increase by 6 to 13% depending on their poverty level. After this initial period of three years, the income from tree crops (fruits, nuts, medicine, essential oil, silk, perfume, honey, timber, animal fodder) exceeds by far the (catalyzer) carbon credits (average crop income for the 25,000 trees including secondary mixed cropping > 150,000 USD). The trees will accumulate carbon for 15 to 75 years depending on the tree species. While trunk wood will be used for construction timber and thus continue to sequester carbon for probably 50 years. While part of the wood will be used for cooking, at least 50% of the tree biomass will be pyrolyzed to biochar to produce organic biochar-based fertilizers and for using the pyrolysis heat for the production of essential oil, pasteurization and fruit or tea leaves drying. Compared to the barren terraces, sparsely covered with grasses and prone to erosion, the forest garden system with organic biochar-based fertilizer, continuous soil cover, mulching, leaf litter fall, root growth and root exudates, rotating cover crops and animal pasture, soil organic carbon (SOC) is expected to increase annually. Therefore, for each participating farmer at least one land spot is GIS marked for soil organic carbon analysis to be executed every five years and to calculate and certify soil organic carbon increases for additional or bonus carbon credits. In our presentation we will show and document the establishment of the forest garden systems, and discuss the link between local carbon sequestration and global carbon markets, the carbon calculation and certification procedures, and the challenge for multiplying such systems inter-regional and internationally.

  19. Temperature Impact on the Forage Quality of Two Wheat Cultivars with Contrasting Capacity to Accumulate Sugars

    OpenAIRE

    Máximo Lorenzo; Silvia G. Assuero; Jorge A. Tognetti

    2015-01-01

    Wheat is increasingly used as a dual-purpose crop (for forage and grain production) worldwide. Plants encounter low temperatures in winter, which commonly results in sugar accumulation. High sugar levels might have a positive impact on forage digestibility, but may also lead to an increased risk of bloat. We hypothesized that cultivars with a lower capacity to accumulate sugars when grown under cold conditions may have a lower bloat risk than higher sugar-accumulating genotypes, without showi...

  20. Nosology in investigation of iodine accumulation ability of thyroid

    International Nuclear Information System (INIS)

    Ishchenko, V.P.; Krupka, I.N.; Romanenko, V.A.; Kalinnik, L.N.; Borodyanskij, N.I.; Petrunin, Yu.I.

    1987-01-01

    The paper is concerned with the construction of algorithms for differential diagnosis of transition nosologic groups (norm, neurosis, hyperthyroidism) using linear discriminant Fisher functions and confidence limits, obtained by the rule 3 S. The calculated procedures for optimal separating hyperplane coefficients are realized by means of modyfying B.I.Kozints algorithms. Diagnostic significance of these classification algorithms is tested on a verified material. Confidence intervals for the values of 131 I accumulation in thyroid gland, constructed with the age account (3 groups), are presented

  1. TRAFIC, a computer program for calculating the release of metallic fission products from an HTGR core

    International Nuclear Information System (INIS)

    Smith, P.D.

    1978-02-01

    A special purpose computer program, TRAFIC, is presented for calculating the release of metallic fission products from an HTGR core. The program is based upon Fick's law of diffusion for radioactive species. One-dimensional transient diffusion calculations are performed for the coated fuel particles and for the structural graphite web. A quasi steady-state calculation is performed for the fuel rod matrix material. The model accounts for nonlinear adsorption behavior in the fuel rod gap and on the coolant hole boundary. The TRAFIC program is designed to operate in a core survey mode; that is, it performs many repetitive calculations for a large number of spatial locations in the core. This is necessary in order to obtain an accurate volume integrated release. For this reason the program has been designed with calculational efficiency as one of its main objectives. A highly efficient numerical method is used in the solution. The method makes use of the Duhamel superposition principle to eliminate interior spatial solutions from consideration. Linear response functions relating the concentrations and mass fluxes on the boundaries of a homogeneous region are derived. Multiple regions are numerically coupled through interface conditions. Algebraic elimination is used to reduce the equations as far as possible. The problem reduces to two nonlinear equations in two unknowns, which are solved using a Newton Raphson technique

  2. Evaluation of scattering laws and cross sections for calculation of production and transport of cold and ultracold neutrons

    International Nuclear Information System (INIS)

    Bernnat, W.; Keinert, J.; Mattes, M.

    2004-01-01

    For the calculation of neutron spectra in cold and super thermal sources scattering laws for a variety of liquid and solid cyrogenic materials were evaluated and prepared for use in deterministic and Monte Carlo transport calculations. For moderator materials like liquid and solid H 2 O, liquid He, liquid D 2 O, liquid and solid H 2 and D 2 , solid CH 4 and structure materials such as Al, Bi, Pb, ZrHx, and graphite scattering law data and cross sections are available. The evaluated data were validated by comparison with measured cross sections and comparison of measured and calculated neutron spectra as far as available. Further applications are the calculation of production and transport and storing of ultra cold neutrons (UCN) in different UCN sources. The data structures of the evaluated data are prepared for the common S N -transport codes and the Monte Carlo Code MCNP. (orig.)

  3. Salt and N leaching and soil accumulation due to cover cropping practices

    Science.gov (United States)

    Gabriel, J. L.; Quemada, M.

    2012-04-01

    Nitrate leaching beyond the root zone can increase water contamination hazards and decrease crop available N. Cover crops used in spite of fallow are an alternative to reduce nitrate contamination in the vadose zone, because reducing drainage and soil mineral N accumulation. Cover crops can improve important characteristics in irrigated land as water retention capacity or soil aggregate stability. However, increasing evapotranspiration and consequent drainage below the root system reduction, could lead to soil salt accumulation. Salinity affects more than 80 million ha of arable land in many areas of the world, and one of the principal causes for yield reduction and even land degradation in the Mediterranean region. Few studies dealt with both problems at the same time. Therefore, it is necessary a long-term evaluation of the potential effect on soil salinity and nitrate leaching, in order to ensure that potential disadvantages that could originate from soil salt accumulation are compensated with all advantages of cover cropping. A study of the soil salinity and nitrate leaching was conducted during 4 years in a semiarid irrigated agricultural area of Central Spain. Three treatments were studied during the intercropping period of maize (Zea mays L.): barley (Hordeum vulgare L.), vetch (Vicia villosa L.) and fallow. Cover crops were killed in March allowing seeding of maize of the entire trial in April, and all treatments were irrigated and fertilised following the same procedure. Before sowing, and after harvesting maize and cover crops, soil salt and nitrate accumulation was determined along the soil profile. Soil analysis was conducted at six depths every 0.20 m in each plot in samples from four 0 to 1.2-m depth holes dug. The electrical conductivity of the saturated paste extract and soil mineral nitrogen was measured in each soil sample. A numerical model based on the Richards water balance equation was applied in order to calculate drainage at 1.2 m depth

  4. Comparative proteomics of Rhizopus delemar ATCC 20344 unravels the role of amino acid catabolism in fumarate accumulation

    OpenAIRE

    Odoni, Dorett I.; Tamayo-Ramos, Juan A.; Sloothaak, Jasper; van Heck, Ruben G.A.; Martins dos Santos, Vitor A.P.; de Graaff, Leo H.; Suarez-Diez, Maria; Schaap, Peter J.

    2017-01-01

    The filamentous fungus Rhizopus delemar naturally accumulates relatively high amounts of fumarate. Although the culture conditions that increase fumarate yields are well established, the network underlying the accumulation of fumarate is not yet fully understood. We set out to increase the knowledge about fumarate accumulation in R. delemar. To this end, we combined a transcriptomics and proteomics approach to identify key metabolic pathways involved in fumarate production in R. delemar, and ...

  5. SPECIFICITY OF ACCUMULATION OF VARIOUS RADIONUCLIDES (137Cs и 90Sr IN SPINACH (Spinacia oleracea L.

    Directory of Open Access Journals (Sweden)

    A. V. Soldatenko

    2016-01-01

    Full Text Available Knowledge of the specificity of accumulation of 137Cs and 90Sr by plants and limits of accumulation by plant fruits plays a key role at breeding of vegetable crops, which make demand for ecological safety of the product. The article is concerned with the study of varietal sources of spinach (Spinacia oleracea L. aimed at development of ecological safety product on the territory polluted by radionuclides.The specificity of accumulation of radionuclides 137Cs and 90Sr was studied in 54 varieties of spinach at industrial contaminated and polluted lands. Experimental tests were conducted in the Moscow and Bryansk regions in 2012 and 2014. The absolute value of radionuclide 90Sr was higher than absolute value of radionuclide 137Cs in all studied zones. It was found that the hazard rate of 90Sr is higher because the level of pollution of product reaches up to 76% from maximum permissible concentration (MPC, while the level of product pollution by 137Cs is 26,4% from MPC. The spinach genotype differentiation for 90Sr in the most environments is lower than differentiation for 137Cs. The histograms of distribution 90Sr and 137Cs showed that samples amount in the groups of accumulation for both radionuclides are equal. Statistically significant data for radionuclides 137Cs and 90Sr in spinach were not obtained. The evaluation of spinach for low content of radionuclides should be conducted separately for each radionuclide on various backgrounds.

  6. Accumulation of heavy metals in edible organs of different meat products available in the markets of lahore, pakistan

    International Nuclear Information System (INIS)

    Baqar, N.; Manzoor, M.; Qadir, M.

    2015-01-01

    The present study assessed the accumulation of selected heavy metals (Cd, Cr, Pb and Cu) indifferent organs including brain, heart, lungs, liver, stomach, kidney and flesh (muscles) of several animals commercially available in the market of Lahore, Pakistan. The concentrations found in different organs of chicken, goat and cow ranged between 0.132-2.165 mg/g for Cd, 0.768-2.335 mg/g for Cr, 0.260-1.411 mg/g for Pb and 0.092-1.195 mg/g for Cu. In the absence of national safety standards in respect to the content of heavy metals in foodstuffs, the results obtained were compared with international guidelines and found concentrations considerably higher than the prescribed safe limits. Therefore, immediate attention must be paid to prevent public health risks associated with the presence of toxic heavy metals in the commercially available meat products. (author)

  7. Copper use and accumulation in catfish culture in the Mekong Delta, Vietnam.

    Science.gov (United States)

    Marcussen, Helle; Løjmand, Helle; Dalsgaard, Anders; Hai, Dao M; Holm, Peter E

    2014-01-01

    Aquaculture of Pangasius hypophthalmus (striped catfish) in Vietnam reached 1.1 million tonnes in 2011 and catfish fillets are exported worldwide. The intensive cultures of catfish mainly in earth ponds have made it necessary to apply CuSO4 and other chemicals to control external parasites and other pathogens. However, accumulation of Cu in aquaculture ponds may pose a hazard to growth of fish or to the aquatic environment. The aim of this study was to determine accumulation of Cu in sediment, water and fish in a catfish pond with a history of repeated treatment with CuSO4 in the Mekong Delta, Vietnam. Copper concentrations in pond sediment were in the interval 21.3-45.7 mg kg(-1) dw and did not exceed the Vietnamese values for soil to be used for agricultural production (70 mg kg(-1) dw.). During three samplings the total mean concentration of Cu in pond water (4 μg L(-1)) did not exceed the LC50-value (70 μg L(-1)) for catfish and the mean dissolved concentration of Cu (0.986 μg L(-1)) did not seem to constitute a risk for the stability of the aquatic ecosystem. No significant variation in Cu concentrations between sampling sites in the pond and depth of sediment profile were determined. The accumulation of Cu in catfish was highest in the liver compared to the skin, gills and muscle tissue. With the current practice of removing pond sludge three to four times during a production cycle little if any Cu seems to accumulate in catfish ponds despite repeated anti-parasite treatments with CuSO4. Further studies are needed to assess the eco-toxicity and impact on agricultural production when pond sediment is discharged into aquatic recipients and used as soil fertilizer.

  8. Accumulation of sup(95m)Tc from sea water by juvenile lobsters (Homarus gammarus L. )

    Energy Technology Data Exchange (ETDEWEB)

    Swift, D.J. (Ministry of Agriculture, Fisheries and Food, Lowestoft (UK). Directorate of Fisheries Research)

    1985-01-01

    The uptake and retention of technetium from sea water by juvenile lobsters, and the effects of moulting on these processes, has been studied using sup(95m)Tc as a tracer. Accumulation was rapid with whole body concentration factors of over 2000 being measured in some lobsters. Uptake was highest immediately before a moult; post-moult there was a fall in accumulation. No simple mathematical equation for technetium accumulation with time was found. The technetium concentration in the moulted exoskeleton increased with time of exposure of the lobsters but never exceeded 2% of the whole body value. The highest percentage of the whole body activity was found in the digestive gland; the green gland had the highest concentration factor. Technetium excretion, following 64 d of accumulation, could be expressed as an exponential rate of loss. The biological half-time was calculated as 53 d. Moulted exoskeletons from these lobsters contained approximately 0.6% of the day zero whole body activity.

  9. Effect of progressive water deficit stress on proline accumulation and ...

    African Journals Online (AJOL)

    Water deficit stress is one of the important factors limiting chickpea production in arid and semi-arid regions of West Asia and North Africa. When water deficit stress is imposed, different molecular and biochemical responses take place. This study was carried out to investigate proline accumulation and protein profiles of ...

  10. Calibration of a He accumulation fluence monitor for fast reactor dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Ito, Chikara [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center

    1997-03-01

    The helium accumulation fluence monitor (HAFM) has been developed for a fast reactor dosimetry. The HAFM measurement system was calibrated using He gas and He implanted samples and the measurement accuracy was confirmed to be less than 5%. Based on the preliminary irradiation test in JOYO, the measured He in the {sup 10}B type HAFM agreed well with the calculated values using the JENDL-3.2 library. (author)

  11. Comparison of calculated integral values using measured and calculated neutron spectra for fusion neutronics analyses

    International Nuclear Information System (INIS)

    Sekimoto, H.

    1987-01-01

    The kerma heat production density, tritum production density, and dose in a lithium-fluoride pile with a deuterium-tritum neutron source were calculated with a data processing code, UFO, from the pulse height distribution of a miniature NE213 neutron spectrometer, and compared with the values calculated with a Monte Carlo code, MORSE-CV. Both the UFO and MORSE-CV values agreed with the statistical error (less than 6%) of the MORSE-CV calculations, except for the outer-most point in the pile. The MORSE-CV values were slightly smaller than the UFO values for almost all cases, and this tendency increased with increasing distance from the neutron source

  12. Design study of an Antiproton Collector for the Antiproton Accumulator (ACOL)

    International Nuclear Information System (INIS)

    Wilson, E.J.N.

    1983-01-01

    The Report gives a full description of an Antiproton Collector Ring which, placed around the existing Antiproton Accumulator at CERN, would enhance the antiproton flux available to both the SPS and LEAR by a factor of ten. The new ring and the focusing devices which precede it are designed to accept a much larger fraction of the antiproton production cone from the target. Each pulse of particles will be pre-cooled before being fed to the Antiproton Accumulator, where improved stochastic cooling systems will build up the stack. A full list of parameters is included. (orig.)

  13. Factors affecting polyhydroxybutyrate accumulation in mesophyll cells of sugarcane and switchgrass

    Science.gov (United States)

    2014-01-01

    Background Polyhydroxyalkanoates are linear biodegradable polyesters produced by bacteria as a carbon store and used to produce a range of bioplastics. Widespread polyhydroxyalkanoate production in C4 crops would decrease petroleum dependency by producing a renewable supply of biodegradable plastics along with residual biomass that could be converted into biofuels or energy. Increasing yields to commercial levels in biomass crops however remains a challenge. Previously, lower accumulation levels of the short side chain polyhydroxyalkanoate, polyhydroxybutyrate (PHB), were observed in the chloroplasts of mesophyll (M) cells compared to bundle sheath (BS) cells in transgenic maize (Zea mays), sugarcane (Saccharum sp.), and switchgrass (Panicum virgatum L.) leading to a significant decrease in the theoretical yield potential. Here we explore various factors which might affect polymer accumulation in mesophyll cells, including targeting of the PHB pathway enzymes to the mesophyll plastid and their access to substrate. Results The small subunit of Rubisco from pea effectively targeted the PHB biosynthesis enzymes to both M and BS chloroplasts of sugarcane and switchgrass. PHB enzyme activity was retained following targeting to M plastids and was equivalent to that found in the BS plastids. Leaf total fatty acid content was not affected by PHB production. However, when fatty acid synthesis was chemically inhibited, polymer accumulated in M cells. Conclusions In this study, we provide evidence that access to substrate and neither poor targeting nor insufficient activity of the PHB biosynthetic enzymes may be the limiting factor for polymer production in mesophyll chloroplasts of C4 plants. PMID:25209261

  14. Characterization of accumulated precipitates during subsurface iron removal

    KAUST Repository

    Van Halem, Doris

    2011-01-01

    The principle of subsurface iron removal for drinking water supply is that aerated water is periodically injected into the aquifer through a tube well. On its way into the aquifer, the injected O2-rich water oxidizes adsorbed Fe 2+, creating a subsurface oxidation zone. When groundwater abstraction is resumed, the soluble Fe 2+ is adsorbed and water with reduced Fe concentrations is abstracted for multiple volumes of the injection water. In this article, Fe accumulation deposits in the aquifer near subsurface treatment wells were identified and characterized to assess the sustainability of subsurface iron removal regarding clogging of the aquifer and the potential co-accumulation of other groundwater constituents, such as As. Chemical extraction of soil samples, with Acid-Oxalate and HNO3, showed that Fe had accumulated at specific depths near subsurface iron removal wells after 12 years of operation. Whether it was due to preferred flow paths or geochemical mineralogy conditions; subsurface iron removal clearly favoured certain soil layers. The total Fe content increased between 11.5 and 390.8 mmol/kg ds in the affected soil layers, and the accumulated Fe was found to be 56-100% crystalline. These results suggest that precipitated amorphous Fe hydroxides have transformed to Fe hydroxides of higher crystallinity. These crystalline, compact Fe hydroxides have not noticeably clogged the investigated well and/or aquifer between 1996 and 2008. The subsurface iron removal wells even need less frequent rehabilitation, as drawdown increases more slowly than in normal production wells. Other groundwater constituents, such as Mn, As and Sr were found to co-accumulate with Fe. Acid extraction and ESEM-EDX showed that Ca occurred together with Fe and by X-ray Powder Diffraction it was identified as calcite. © 2010 Elsevier Ltd. All rights reserved.

  15. Action of UV-A and blue light on enzymes activity and accumulation of lipid peroxidation products in attached and detached frog retinas

    Science.gov (United States)

    Lapina, Victoria A.; Doutsov, Alexander E.

    1994-07-01

    The effect of the UV-A and blue light on the accumulation of lipid peroxidation products and activities of succinate dehydrogenase and superoxide dismutase in the retina was examined in eye cup model of dark and light adapted frogs R. temporaria. Retinas were exposed to UV-A radiation (8 mW/cm2) and blue light (10 to 150 mW/cm2) for periods from 5 min to 1 hr. We have measured TBA-active products both in the retina homogenates and in the reaction media. Enzyme activities was measured in the retina homogenates only. The measurements revealed a significant increase in the endogenous and exogenous forms of lipid peroxidation products in the retina of dark adapted frog (1.6+/- 0.4; 1.4+/- 0.3 nmole TBA-active products per mg protein, respectively) compared to light adapted (0.85+/- 0.16; 0.32+/- 0.06 nmole TBA-active products per mg protein, respectively). In the same conditions succinate dehydrogenase activity was decline more than 50% but superoxide dismutase activity didn't decrease. Disorganized inner and outer segments were observed after 40 min exposures. No light microscopic changes were detected after 5 min exposures. Light damage was significantly higher in the retina of dark adapted frog. The results indicate that the retina from eye cup of dark adapted frog is more susceptible to UV-A and blue light damages.

  16. DspA/E contributes to apoplastic accumulation of ROS in nonhost A. thaliana

    Directory of Open Access Journals (Sweden)

    Alban eLaunay

    2016-04-01

    Full Text Available The bacterium Erwinia amylovora is responsible for the fire blight disease of Maleae, which provokes necrotic symptoms on aerial parts. The pathogenicity of this bacterium in hosts relies on its type three-secretion system (T3SS, a molecular syringe that allows the bacterium to inject effectors into the plant cell. E. amylovora-triggered disease in host plants is associated with the T3SS-dependent production of reactive oxygen species (ROS, although ROS are generally associated with resistance in other pathosystems. We showed previously that E. amylovora can multiply transiently in the nonhost plant Arabidopsis thaliana and that a T3SS-dependent production of intracellular ROS occurs during this interaction. In the present work we characterize the localization and source of hydrogen peroxide accumulation following E. amylovora infection. Transmission electron microscope (TEM analysis of infected tissues showed that hydrogen peroxide accumulation occurs in the cytosol, plastids, peroxisomes, and mitochondria as well as in the apoplast. Furthermore, TEM analysis showed that an E. amylovora dspA/E-deficient strain does not induce hydrogen peroxide accumulation in the apoplast. Consistently, a transgenic line expressing DspA/E accumulated ROS in the apoplast. The NADPH oxidase-deficient rbohD mutant showed a very strong reduction in hydrogen peroxide accumulation in response to E. amylovora inoculation. However, we did not find an increase in bacterial titers of E. amylovora in the rbohD mutant and the rbohD mutation did not suppress the toxicity of DspA/E when introgressed into a DspA/E-expressing transgenic line. Co-inoculation of E. amylovora with cycloheximide (CHX, which we found previously to suppress callose deposition and allow strong multiplication of E. amylovora in A. thaliana leaves, led to a strong reduction of apoplastic ROS accumulation but did not affect intracellular ROS. Our data strongly suggest that apoplastic ROS accumulation is

  17. Accumulation status, sources and phytoavailability of metals in greenhouse vegetable production systems in Beijing, China.

    Science.gov (United States)

    Xu, Li; Lu, Anxiang; Wang, Jihua; Ma, Zhihong; Pan, Ligang; Feng, Xiaoyuan; Luan, Yunxia

    2015-12-01

    The accumulation status, sources and phytoavailability of selected metals in greenhouse vegetable production systems in peri-urban areas of Beijing were investigated. The mean concentrations of As, Cd, Cr, Hg and Pb in greenhouse soils were 8.44, 0.25, 69.0, 0.09 and 22.0 mg kg(-1), dw, respectively. According to principal component analysis, As, Cd, Cr and Hg are mainly from anthropogenic source, but Pb is likely from natural source. Metal concentrations in all vegetable samples were decreased in the order of Cr>As>Pb>Cd>Hg. Compared with root and fruit vegetables, leaf vegetables had relatively high concentrations and transfer factors of heavy metals, except for Cd. By including soil pH, OM and greenhouse soil metals, 10 empirical models were derived using stepwise multiple linear regression analysis to predict heavy metal concentrations in the edible parts of different vegetables. Among the different vegetable groups, the highest intakes of metals occurred through consumption of leaf vegetables for the two age groups, except for Cd. The HI value of the studied metals were all below 1, indicating that consumption of vegetables grown in greenhouse soils was of low risk to consumers in our study area. Copyright © 2015 Elsevier Inc. All rights reserved.

  18. Evaluation of scattering laws and cross sections for calculation of production and transport of cold and ultracold neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Bernnat, W.; Keinert, J.; Mattes, M. [Inst. for Nuclear Energy and Energy Systems, Univ. of Stuttgart, Stuttgart (Germany)

    2004-03-01

    For the calculation of neutron spectra in cold and super thermal sources scattering laws for a variety of liquid and solid cyrogenic materials were evaluated and prepared for use in deterministic and Monte Carlo transport calculations. For moderator materials like liquid and solid H{sub 2}O, liquid He, liquid D{sub 2}O, liquid and solid H{sub 2} and D{sub 2}, solid CH{sub 4} and structure materials such as Al, Bi, Pb, ZrHx, and graphite scattering law data and cross sections are available. The evaluated data were validated by comparison with measured cross sections and comparison of measured and calculated neutron spectra as far as available. Further applications are the calculation of production and transport and storing of ultra cold neutrons (UCN) in different UCN sources. The data structures of the evaluated data are prepared for the common S{sub N}-transport codes and the Monte Carlo Code MCNP. (orig.)

  19. Ion accumulation in an electron plasma confined on magnetic surfaces

    International Nuclear Information System (INIS)

    Berkery, John W.; Marksteiner, Quinn R.; Pedersen, Thomas Sunn; Kremer, Jason P.

    2007-01-01

    Accumulation of ions can alter and may destabilize the equilibrium of an electron plasma confined on magnetic surfaces. An analysis of ion sources and ion content in the Columbia Non-neutral Torus (CNT) [T.S. Pedersen, J.P. Kremer, R.G. Lefrancois, Q. Marksteiner, N. Pomphrey, W. Reiersen, F. Dahlgreen, and X. Sarasola, Fusion Sci. Technol. 50, 372 (2006)] is presented. In CNT ions are created preferentially at locations of high electron temperature, near the outer magnetic surfaces. A volumetric integral of n e ν iz gives an ion creation rate of 2.8x10 11 ions/s. This rate of accumulation would cause neutralization of a plasma with 10 11 electrons in about half a second. This is not observed experimentally, however, because currently in CNT ions are lost through recombination on insulated rods. From a steady-state balance between the calculated ion creation and loss rates, the equilibrium ion density in a 2x10 -8 Torr neutral pressure, 7.5x10 11 m -3 electron density plasma in CNT is calculated to be n i =6.2x10 9 m -3 , or 0.8%. The ion density is experimentally measured through the measurement of the ion saturation current on a large area probe to be about 6.0x10 9 m -3 for these plasmas, which is in good agreement with the predicted value

  20. The calculation of specific heats for some important solid components in hydrogen production process based on CuCl cycle

    Directory of Open Access Journals (Sweden)

    Avsec Jurij

    2014-01-01

    Full Text Available Hydrogen is one of the most promising energy sources of the future enabling direct production of power and heat in fuel cells, hydrogen engines or furnaces with hydrogen burners. One of the last remainder problems in hydrogen technology is how to produce a sufficient amount of cheap hydrogen. One of the best options is large scale thermochemical production of hydrogen in combination with nuclear power plant. copper-chlorine (CuCl cycle is the most promissible thermochemical cycle to produce cheap hydrogen.This paper focuses on a CuCl cycle, and the describes the models how to calculate thermodynamic properties. Unfortunately, for many components in CuCl cycle the thermochemical functions of state have never been measured. This is the reason that we have tried to calculate some very important thermophysical properties. This paper discusses the mathematical model for computing the thermodynamic properties for pure substances and their mixtures such as CuCl, HCl, Cu2OCl2 important in CuCl hydrogen production in their fluid and solid phase with an aid of statistical thermodynamics. For the solid phase, we have developed the mathematical model for the calculation of thermodynamic properties for polyatomic crystals. In this way, we have used Debye functions and Einstein function for acoustical modes and optical modes of vibrations to take into account vibration of atoms. The influence of intermolecular energy we have solved on the basis of Murnaghan equation of state and statistical thermodynamics.

  1. Temperature Impact on the Forage Quality of Two Wheat Cultivars with Contrasting Capacity to Accumulate Sugars

    Directory of Open Access Journals (Sweden)

    Máximo Lorenzo

    2015-08-01

    Full Text Available Wheat is increasingly used as a dual-purpose crop (for forage and grain production worldwide. Plants encounter low temperatures in winter, which commonly results in sugar accumulation. High sugar levels might have a positive impact on forage digestibility, but may also lead to an increased risk of bloat. We hypothesized that cultivars with a lower capacity to accumulate sugars when grown under cold conditions may have a lower bloat risk than higher sugar-accumulating genotypes, without showing significantly lower forage digestibility. This possibility was studied using two wheat cultivars with contrasting sugar accumulation at low temperature. A series of experiments with contrasting temperatures were performed in controlled-temperature field enclosures (three experiments and growth chambers (two experiments. Plants were grown at either cool (8.1 °C–9.3 °C or warm (15.7 °C–16.5 °C conditions in field enclosures, and at either 5 °C or 25 °C in growth chambers. An additional treatment consisted of transferring plants from cool to warm conditions in the field enclosures and from 5 °C to 25 °C in the growth chambers. The plants in the field enclosure experiments were exposed to higher irradiances (i.e., 30%–100% than those in the growth chambers. Our results show that (i low temperatures led to an increased hemicellulose content, in parallel with sugar accumulation; (ii low temperatures produced negligible changes in in vitro dry matter digestibility while leading to a higher in vitro rumen gas production, especially in the higher sugar-accumulating cultivar; (iii transferring plants from cool to warm conditions led to a sharp decrease in in vitro rumen gas production in both cultivars; and (iv light intensity (in contrast to temperature appeared to have a lower impact on forage quality.

  2. Calculation code of mass and heat transfer in a pulsed column for Purex process

    International Nuclear Information System (INIS)

    Tsukada, Takeshi; Takahashi, Keiki

    1993-01-01

    A calculation code for extraction behavior analysis in a pulsed column employed at an extraction process of a reprocessing plant was developed. This code was also combined with our previously developed calculation code for axial temperature profiles in a pulsed column. The one-dimensional dispersion model was employed for both of the extraction behavior analysis and the axial temperature profile analysis. The reported values of the fluid characteristics coefficient, the transfer coefficient and the diffusivities in the pulsed column were used. The calculated concentration profiles of HNO 3 , U and Pu for the steady state have a good agreement with the reported experimental results. The concentration and temperature profiles were calculated under the operation conditions which induce the abnormal U extraction behavior, i.e. U extraction zone is moved to the bottom of the column. Thought there is slight difference between calculated and experimental value, it is appeared that our developed code can be applied to the simulation under the normal operation condition and the relatively slowly transient condition. Pu accumulation phenomena was analyzed with this code and the accumulation tendency is similar to the reported analysis results. (author)

  3. Ecological strategies of Al-accumulating and non-accumulating functional groups from the cerrado sensu stricto

    Directory of Open Access Journals (Sweden)

    Marcelo C. de Souza

    2015-06-01

    Full Text Available The cerrado's flora comprises aluminum-(Al accumulating and non-accumulating plants, which coexist on acidic and Al-rich soils with low fertility. Despite their existence, the ecological importance or biological strategies of these functional groups have been little explored. We evaluated the leaf flushing patterns of both groups throughout a year; leaf concentrations of N, P, K, Ca, Mg, S, Al, total flavonoids and polyphenols; as well as the specific leaf area (SLA on young and mature leaves within and between the groups. In Al-accumulating plants, leaf flushed throughout the year, mainly in May and September; for non-accumulating plants, leaf flushing peaked at the dry-wet seasons transition. However, these behaviors could not be associated with strategies for building up concentrations of defense compounds in leaves of any functional groups. Al-accumulating plants showed low leaf nutrient concentrations, while non-accumulating plants accumulated more macronutrients and produced leaves with high SLA since the juvenile leaf phase. This demonstrates that the increase in SLA is slower in Al-accumulating plants that are likely to achieve SLA values comparable to the rest of the plant community only in the wet season, when sunlight capture is important for the growth of new branches.

  4. Ecological strategies of Al-accumulating and non-accumulating functional groups from the cerrado sensu stricto.

    Science.gov (United States)

    Souza, Marcelo C de; Bueno, Paula C P; Morellato, Leonor P C; Habermann, Gustavo

    2015-01-01

    The cerrado's flora comprises aluminum-(Al) accumulating and non-accumulating plants, which coexist on acidic and Al-rich soils with low fertility. Despite their existence, the ecological importance or biological strategies of these functional groups have been little explored. We evaluated the leaf flushing patterns of both groups throughout a year; leaf concentrations of N, P, K, Ca, Mg, S, Al, total flavonoids and polyphenols; as well as the specific leaf area (SLA) on young and mature leaves within and between the groups. In Al-accumulating plants, leaf flushed throughout the year, mainly in May and September; for non-accumulating plants, leaf flushing peaked at the dry-wet seasons transition. However, these behaviors could not be associated with strategies for building up concentrations of defense compounds in leaves of any functional groups. Al-accumulating plants showed low leaf nutrient concentrations, while non-accumulating plants accumulated more macronutrients and produced leaves with high SLA since the juvenile leaf phase. This demonstrates that the increase in SLA is slower in Al-accumulating plants that are likely to achieve SLA values comparable to the rest of the plant community only in the wet season, when sunlight capture is important for the growth of new branches.

  5. Accumulation of silver nanoparticles by cultured primary brain astrocytes

    Energy Technology Data Exchange (ETDEWEB)

    Luther, Eva M; Koehler, Yvonne; Dringen, Ralf [Center for Biomolecular Interactions Bremen, University of Bremen, PO Box 330440, D-28334 Bremen (Germany); Diendorf, Joerg; Epple, Matthias, E-mail: ralf.dringen@uni-bremen.de [Inorganic Chemistry and Center for Nanointegration Duisburg-Essen, University of Duisburg-Essen, Universitaetsstrasse 5-7, D-45117 Essen (Germany)

    2011-09-16

    Silver nanoparticles (AgNP) are components of various food industry products and are frequently used for medical equipment and materials. Although such particles enter the vertebrate brain, little is known on their biocompatibility for brain cells. To study the consequences of an AgNP exposure of brain cells we have treated astrocyte-rich primary cultures with polyvinylpyrrolidone (PVP)-coated AgNP. The incubation of cultured astrocytes with micromolar concentrations of AgNP for up to 24 h resulted in a time- and concentration-dependent accumulation of silver, but did not compromise the cell viability nor lower the cellular glutathione content. In contrast, the incubation of astrocytes for 4 h with identical amounts of silver as AgNO{sub 3} already severely compromised the cell viability and completely deprived the cells of glutathione. The accumulation of AgNP by astrocytes was proportional to the concentration of AgNP applied and significantly lowered by about 30% in the presence of the endocytosis inhibitors chloroquine or amiloride. Incubation at 4 {sup 0}C reduced the accumulation of AgNP by 80% compared to the values obtained for cells that had been exposed to AgNP at 37 {sup 0}C. These data demonstrate that viable cultured brain astrocytes efficiently accumulate PVP-coated AgNP in a temperature-dependent process that most likely involves endocytotic pathways.

  6. Application of flow-controllable accumulator and performance analysis in Korean Nuclear Power Plants

    International Nuclear Information System (INIS)

    Jung, Byung-Ryul; Lee, Un-Chul

    1997-01-01

    The Korean Yonggwang Nuclear Power Plants 3 ampersand 4(YGN 3 ampersand 4) are the two-loop pressurized water reactor (PWR) nuclear steam supply systems, rated at 2,815 MW(thermal). They incorporate the safety injection system (SIS) consisting of the two high pressure (HPSI) pumps, two low pressure safety injection (LPSI) pumps, and four accumulators. The SIS is two headered arrangements, each to four cold legs injection (CLI) type which provides cooling to the core in the highly unlikely event of a loss-of-coolant accident (LOCA). In the current SIS, the LPSI pumps automatically start during a LOCA, and also provide the residual heat removal capability during the shutdown cooling. This paper presents the feasibility of the removal of the LPSI from the existing SIS with minor system changes, including the increase up to four in the HPSI pumps, direct vessel injection(DVI), and the flow-controllable accumulators. A double-ended rupture of one of the four cold legs in the YGN 3 ampersand 4 was simulated using RELAP5/MOD3.1 to determine the feasibility of the application of this new SIS design to the current nuclear power plants. As a result, the calculated reflooding peak cladding surface temperature(PCT) was comparable to that of original base calculation, and the downcomer and the core collapsed liquid level during reflooding were also comparable to those in the current safety system design. This large break, cold-leg LOCA analysis addresses the reflooding capability without credit for a LPSI pump system and the applicability of the new flow-controllable accumulator. Also this analysis confirms that the combination of new flow-controllable accumulators, DVI and the increased HPSI pumps maintain the peak cladding temperature below the prescribed limits. 14 refs., 4 figs., 3 tabs

  7. HETC-3STEP calculations of proton induced nuclide production cross sections at incident energies between 20 MeV and 5 GeV

    Energy Technology Data Exchange (ETDEWEB)

    Takada, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Yoshizawa, Nobuaki; Ishibashi, Kenji

    1996-08-01

    For the OECD/NEA code intercomparison, nuclide production cross sections of {sup 16}O, {sup 27}Al, {sup nat}Fe, {sup 59}Co, {sup nat}Zr and {sup 197}Au for the proton incidence with energies of 20 MeV to 5 GeV are calculated with the HETC-3STEP code based on the intranuclear cascade evaporation model including the preequilibrium and high energy fission processes. In the code, the level density parameter derived by Ignatyuk, the atomic mass table of Audi and Wapstra and the mass formula derived by Tachibana et al. are newly employed in the evaporation calculation part. The calculated results are compared with the experimental ones. It is confirmed that HETC-3STEP reproduces the production of the nuclides having the mass number close to that of the target nucleus with an accuracy of a factor of two to three at incident proton energies above 100 MeV for {sup nat}Zr and {sup 197}Au. However, the HETC-3STEP code has poor accuracy on the nuclide production at low incident energies and the light nuclide production through the fragmentation process induced by protons with energies above hundreds of MeV. Therefore, further improvement is required. (author)

  8. Uncertainties in source term calculations generated by the ORIGEN2 computer code for Hanford Production Reactors

    International Nuclear Information System (INIS)

    Heeb, C.M.

    1991-03-01

    The ORIGEN2 computer code is the primary calculational tool for computing isotopic source terms for the Hanford Environmental Dose Reconstruction (HEDR) Project. The ORIGEN2 code computes the amounts of radionuclides that are created or remain in spent nuclear fuel after neutron irradiation and radioactive decay have occurred as a result of nuclear reactor operation. ORIGEN2 was chosen as the primary code for these calculations because it is widely used and accepted by the nuclear industry, both in the United States and the rest of the world. Its comprehensive library of over 1,600 nuclides includes any possible isotope of interest to the HEDR Project. It is important to evaluate the uncertainties expected from use of ORIGEN2 in the HEDR Project because these uncertainties may have a pivotal impact on the final accuracy and credibility of the results of the project. There are three primary sources of uncertainty in an ORIGEN2 calculation: basic nuclear data uncertainty in neutron cross sections, radioactive decay constants, energy per fission, and fission product yields; calculational uncertainty due to input data; and code uncertainties (i.e., numerical approximations, and neutron spectrum-averaged cross-section values from the code library). 15 refs., 5 figs., 5 tabs

  9. Enhanced accumulation of atropine in Atropa belladonna transformed by Rac GTPase gene isolated from Scoparia dulcis.

    Science.gov (United States)

    Asano, Kyouhei; Lee, Jung-Bum; Yamamura, Yoshimi; Kurosaki, Fumiya

    2013-12-01

    Leaf tissues of Atropa belladonna were transformed by Sdrac2, a Rac GTPase gene, that is isolated from Scoparia dulcis, and the change in atropine concentration of the transformants was examined. Re-differentiated A. belladonna overexpressing Sdrac2 accumulated considerable concentration of atropine in the leaf tissues, whereas the leaves of plants transformed by an empty vector accumulated only a very low concentration of the compound. A. belladonna transformed by CASdrac2, a modified Sdrac2 of which translate was expected to bind guanosine triphosphate (GTP) permanently, accumulated very high concentrations of atropine (approximately 2.4-fold excess to those found in the wild-type plant in its natural habitat). In sharp contrast, the atropine concentration in transformed A. belladonna prepared with negatively modified Sdrac2, DNSdrac2, expected to bind guanosine diphosphate instead of GTP, was very low. These results suggested that Rac GTPases play an important role in the regulation of secondary metabolism in plant cells and that overexpression of the gene(s) may be capable of enhancing the production of natural products accumulated in higher plant cells.

  10. Expanded Study on the accumulation effect of tourism under the constraint of structure

    Science.gov (United States)

    Wang, Qiang; Yang, Zhenzhi; Huang, Lu

    2017-05-01

    There is a mutual influence between departmental structure and accumulation and growth. Therefore, the accumulation and growth of the tourism industry will be subject to certain restrictions on the industrial structure, and, conversely, it will have an impact on the existing industrial structure. Li Jingyi reported special research in the paper called "Research on tourism growth based on structural constraints" about the relationship between the growth of tourism and the existing industrial structure. It pointed out the specific interdependence between tourism and other economic sectors in terms of accumulation and growth. However, the research of Li Jingyi is based on the trichotomy of social product value. It is too abstract, while the study is understandable in theory. In practice, it is difficult to use the model of the paper to deal with specific problems. Therefore, how to improve the industry association model in the paper of Li and make it more in line with the actual situation becomes our concern. In this paper, the author hopes to improve the model of Li's paper by simplifying the decomposition of social product value. At the same time, it makes a further study on accumulation elasticity and growth elasticity. On this basis, some suggestions are put forward to guide the development of other industries based on the tourism industry.

  11. Expanded Study on the accumulation effect of tourism under the constraint of structure

    Directory of Open Access Journals (Sweden)

    Wang Qiang

    2017-05-01

    Full Text Available There is a mutual influence between departmental structure and accumulation and growth. Therefore, the accumulation and growth of the tourism industry will be subject to certain restrictions on the industrial structure, and, conversely, it will have an impact on the existing industrial structure. Li Jingyi reported special research in the paper called “Research on tourism growth based on structural constraints” about the relationship between the growth of tourism and the existing industrial structure. It pointed out the specific interdependence between tourism and other economic sectors in terms of accumulation and growth. However, the research of Li Jingyi is based on the trichotomy of social product value. It is too abstract, while the study is understandable in theory. In practice, it is difficult to use the model of the paper to deal with specific problems. Therefore, how to improve the industry association model in the paper of Li and make it more in line with the actual situation becomes our concern. In this paper, the author hopes to improve the model of Li’s paper by simplifying the decomposition of social product value. At the same time, it makes a further study on accumulation elasticity and growth elasticity. On this basis, some suggestions are put forward to guide the development of other industries based on the tourism industry.

  12. INTEGRATED ASSESSMENT AND GEOSPATIAL ANALYSIS OF ACCUMULATION OF PETROLEUM HYDROCARBONS IN THE SOIL COVER OF SAKHALIN ISLAND

    Directory of Open Access Journals (Sweden)

    V. V. Dmitriev

    2017-01-01

    Full Text Available The article considers the approach to the integral estimation of the assessment of petroleum hydrocarbons (PHc in the soil cover of Sakhalin Island. The soil map of Sakhalin was used as the cartographic base for this work. The soil map includes 103 soil polygons. An additional information on soils was also taken from The Soil Atlas of the Russian Federation. As an integral criterion for the accumulation of PHc, it is proposed to use an integral indicator calculated on the basis of 5 evaluation criteria. The choice of criteria for the assessment was based on the works of Russian scientists. The evaluation criteria on each of the polygons include information on the soil texture, the total thickness of the organic and humus horizons, the content of organic carbon in these horizons and the content of organic carbon in the mineral horizons, as well as the presence of a gley barrier.The calculation of the integral indicator is based on the principles of the ASPID methodology. On this basis, the authors compiled the map of the potential capacity of Sakhalin soils to accumulate petroleum hydrocarbons. On the basis of GIS-technology using the estimates of the integral indicator, the analysis has been performed revealing the features of spatial differentiation of PHc accumulation in the soil cover.The analysis and assessment of the accumulations of petroleum hydrocarbons has shown that peaty and peat boggy soil have the greatest ability to holding the PHc. The lowest ability to accumulate petroleum hydrocarbons is typical of illuvial-ferruginous podzols (illuvial low-humic podzols. The soils of this group occupy 1% of the island. In general, soils with low and very low hydrocarbon accumulation capacity occupy less than forty percent of the territory. 

  13. The impact of shrubbification on soil organic matter accumulation

    Science.gov (United States)

    Street, L.; Wookey, P. A.; Subke, J. A.; Baxter, R.; Garnett, M.

    2017-12-01

    The degree to which increasing vegetation productivity in the Arctic can offset permafrost carbon emissions under a warming climate is highly uncertain. Most ecosystem or earth system models predict that plant C inputs to permafrost soils will balance or exceed losses with warming, at least until about mid-century. Observations on the ground however, question whether vegetation change in Arctic ecosystems will result in even a transient net C sink. In the European Arctic, for example, rhizosphere processes associated with ectomycorrhizal (ECM) fungi have been implicated in driving rapid cycling - and thus lower storage - of soil organic C (SOC) under deciduous shrubs. Short-term incubation studies also show that decomposition of SOC can be stimulated or "primed" by new inputs of labile plant C. The implication is that as Arctic vegetation shifts towards a greater abundance of productive, and mostly ECM, deciduous trees and shrubs, net C losses from soils may result. Over decadal timescales however, the impact of changing vegetation and associated rhizosphere processes on C stock trajectories is complex - shifts in productivity and mycorrhizal status will be accompanied by other biological and physical changes that can impact decomposition. Encroachment of shrubs will likely influence both litter quality and quantity, as well as soil temperature and moisture regimes due to altered transpiration rates, shading and snow accumulation. Short-term studies, and those based on instantaneous flux measurements, can provide only limited information as to what the impact of shrubbification on SOC stocks will be. Here we use radiocarbon data, in combination with a vertically-resolved isotopic model, to examine how and why SOC accumulation in tundra soils differs between vegetation types over decades to centuries. We compare soil profiles under ECM birch, N-fixing alder, and ericaceous/lichen heath tundra in the Canadian Arctic. Early model results suggest that under alder

  14. The Accumulation and Retention of Zine-65 and Cobalt-60 by The Fresh Water Fish CLARIAS LAZERA

    International Nuclear Information System (INIS)

    Abdel Malik, W.E.Y.; Ibrahim, A.S.; Badawy, S.A.

    2003-01-01

    Some parameters affecting the accumulation and retention of 65 Zn and 60 Co radionuclides by the fresh water fish CLARIAS LAZERA from the contaminated filtered Ismail ia Canal water(FICW) have been investigated. It has been observed that the accumulated activity (KBq/g) increased with increasing exposure time with the contaminated FICW. This kind of bony fish has been shown to accumulate 65 Zn > 60 Co. The increase of the studied radionuclide carrier concentration in the canal water increased the fish uptake of both radionuclides. The increase of ph of the FICW decreased the accumulated activity by the fish. On the other hand, the retention of those radionuclides by this fish was investigated. It was possible from this study to give preliminary data for the calculation of the radiation dose that might be delivered to man eating the contaminated fish

  15. Estimation of erosion-accumulative processes at the Inia River’s mouth near high-rise construction zones.

    Directory of Open Access Journals (Sweden)

    Sineeva Natalya

    2018-01-01

    Full Text Available Our study relevance is due to the increasing man-made impact on water bodies and associated land resources within the urban areas, as a consequence, by a change in the morphology and dynamics of Rivers’ canals. This leads to the need to predict the development of erosion-accumulation processes, especially within the built-up urban areas. Purpose of the study is to develop programs on the assessment of erosion-accumulation processes at a water body, a mouth area of the Inia River, in the of perspective high-rise construction zone of a residential microdistrict, the place, where floodplain-channel complex is intensively expected to develop. Results of the study: Within the velocities of the water flow comparing, full-scale measured conditions, and calculated from the model, a slight discrepancy was recorded. This allows us to say that the numerical model reliably describes the physical processes developing in the River. The carried out calculations to assess the direction and intensity of the channel re-formations, made us possible to conclude, there was an insignificant predominance of erosion processes over the accumulative ones on the undeveloped part of the Inia River (the processes activity is noticeable only in certain areas (by the coasts and the island. Importance of the study: The study on the erosion-accumulation processes evaluation can be used in design decisions for the future high-rise construction of this territory, which will increase their economic efficiency.

  16. Comparative proteomics of Rhizopus delemar ATCC 20344 unravels the role of amino acid catabolism in fumarate accumulation

    Directory of Open Access Journals (Sweden)

    Dorett I. Odoni

    2017-03-01

    Full Text Available The filamentous fungus Rhizopus delemar naturally accumulates relatively high amounts of fumarate. Although the culture conditions that increase fumarate yields are well established, the network underlying the accumulation of fumarate is not yet fully understood. We set out to increase the knowledge about fumarate accumulation in R. delemar. To this end, we combined a transcriptomics and proteomics approach to identify key metabolic pathways involved in fumarate production in R. delemar, and propose that a substantial part of the fumarate accumulated in R. delemar during nitrogen starvation results from the urea cycle due to amino acid catabolism.

  17. Electric-field induced spin accumulation in the Landau level states of topological insulator thin films

    Science.gov (United States)

    Siu, Zhuo Bin; Chowdhury, Debashree; Basu, Banasri; Jalil, Mansoor B. A.

    2017-08-01

    A topological insulator (TI) thin film differs from the more typically studied thick TI system in that the former has both a top and a bottom surface where the states localized at both surfaces can couple to one other across the finite thickness. An out-of-plane magnetic field leads to the formation of discrete Landau level states in the system, whereas an in-plane magnetization breaks the angular momentum symmetry of the system. In this work, we study the spin accumulation induced by the application of an in-plane electric field to the TI thin film system where the Landau level states and inter-surface coupling are simultaneously present. We show, via Kubo formula calculations, that the in-plane spin accumulation perpendicular to the magnetization due to the electric field vanishes for a TI thin film with symmetric top and bottom surfaces. A finite in-plane spin accumulation perpendicular to both the electric field and magnetization emerges upon applying either a differential magnetization coupling or a potential difference between the two film surfaces. This spin accumulation results from the breaking of the antisymmetry of the spin accumulation around the k-space equal-energy contours.

  18. Spatial Variability of accumulation across the Western Greenland Ice Sheet Percolation Zone from ground-penetrating-radar and shallow firn cores

    Science.gov (United States)

    Lewis, G.; Osterberg, E. C.; Hawley, R. L.; Marshall, H. P.; Birkel, S. D.; Meehan, T. G.; Graeter, K.; Overly, T. B.; McCarthy, F.

    2017-12-01

    The mass balance of the Greenland Ice Sheet (GrIS) in a warming climate is of critical interest to scientists and the general public in the context of future sea-level rise. Increased melting in the GrIS percolation zone over the past several decades has led to increased mass loss at lower elevations due to recent warming. Uncertainties in mass balance are especially large in regions with sparse and/or outdated in situ measurements. This study is the first to calculate in situ accumulation over a large region of western Greenland since the Program for Arctic Regional Climate Assessment campaign during the 1990s. Here we analyze 5000 km of 400 MHz ground penetrating radar data and sixteen 25-33 m-long firn cores in the western GrIS percolation zone to determine snow accumulation over the past 50 years. The cores and radar data were collected as part of the 2016-2017 Greenland Traverse for Accumulation and Climate Studies (GreenTrACS). With the cores and radar profiles we capture spatial accumulation gradients between 1850-2500 m a.s.l and up to Summit Station. We calculate accumulation rates and use them to validate five widely used regional climate models and to compare with IceBridge snow and accumulation radars. Our results indicate that while the models capture most regional spatial climate patterns, they lack the small-scale spatial variability captured by in situ measurements. Additionally, we evaluate temporal trends in accumulation at ice core locations and throughout the traverse. Finally, we use empirical orthogonal function and correlation analyses to investigate the principal drivers of radar-derived accumulation rates across the western GrIS percolation zone, including major North Atlantic climate modes such as the North Atlantic Oscillation, Atlantic Multidecadal Oscillation, and Greenland Blocking Index.

  19. The role of FFM accumulation and skeletal muscle architecture in powerlifting performance.

    Science.gov (United States)

    Brechue, William F; Abe, Takashi

    2002-02-01

    The purpose of this study was to determine the distribution and architectural characteristics of skeletal muscle in elite powerlifters, and to investigate their relationship to fat-free mat (FFM) accumulation and powerlifting performance. Twenty elite male powerlifters (including four world and three US national champions) volunteered for this study. FFM, skeletal muscle distribution (muscle thickness at 13 anatomical sites), and isolated muscle thickness and fascicle pennation angle (PAN) of the triceps long-head (TL), vastus lateralis, and gastrocnemius medialis (MG) muscles were measured with B-mode ultrasound. Fascicle length (FAL) was calculated. Best lifting performance in the bench press (BP), squat lift (SQT), and dead lift (DL) was recorded from competition performance. Significant correlations (P FFM and FFM relative to standing height (r = 0.86 to 0.95, P FFM (r = 0.59, P FFM and, therefore, may be limited by the ability to accumulate FFM. Additionally, muscle architecture appears to play an important role in powerlifting performance in that greater fascicle lengths are associated with greater FFM accumulation and powerlifting performance.

  20. Oxidative demethylation of lanosterol in cholesterol biosynthesis: accumulation of sterol intermediates

    International Nuclear Information System (INIS)

    Shafiee, A.; Trzaskos, J.M.; Paik, Y.K.; Gaylor, J.L.

    1986-01-01

    With [ 3 H-24,25]-dihydrolanosterol as substrate, large-scale metabolic formation of intermediates of lanosterol demethylation was carried out to identify all compounds in the metabolic process. Utilizing knowledge of electron transport of lanosterol demethylation, we interrupted the demethylation reaction allowing accumulation and confirmation of the structure of the oxygenated intermediates lanost-8-en-3 beta,32-diol and 3 beta-hydroxylanost-8-en-32-al, as well as the demethylation product 4,4-dimethyl-cholesta-8,14-dien-3 beta-ol. Further metabolism of the delta 8.14-diene intermediate to a single product 4,4-dimethyl-cholest-8-en-3 beta-ol occurs under interruption conditions in the presence of 0.5 mM CN-1. With authentic compounds, each intermediate has been rigorously characterized by high performance liquid chromatography and gas-liquid chromatography plus mass spectral analysis of isolated and derivatized sterols. Intermediates that accumulated in greater abundance were further characterized by ultraviolet, 1 H-NMR, and infrared spectroscopy of the isolated sterols

  1. 137Cs accumulation in components of pine stands in Polessye of Ukraine

    International Nuclear Information System (INIS)

    Krasnov, V.P.; Orlov, A.A.; Gusarevich, M.G.

    2005-01-01

    Distribution of 137 Cs specific activity in structural components of Scotch pine in different parts of crone and tree trunk (according the height) was analyzed; the average value 137 Cs transfer factor (TF) for all investigated components was calculated. Decreasing of 137 Cs specific activity and values of TF from upper crone part through middle to the lowest one has been shown for the majority pine crone components in edatops B 2 and B 3 . It was drown a calculation that 137 Cs specific activities and TF values stably decreased in tree trunk components from upper part through middle to the lowest one in edatop B 3 . In edatop B 2 decreasing of 137 Cs specific activity and TF values for external and internal bark was also revealed in the same direction. The decreasing of 137 Cs specific activity and TF values for wood was revealed from upper part of the trunk to middle one and their increasing to the lowest tree trunk part. It was shown that physiologically active organs and tissues in the pine are characterized by the maximum accumulation: one-year-o;d shoots, one-year-old needles, internal bark. It was drown an important conclusion that part of tree trunk (according to its height), which used as fuel wood and construction materials, is a strong modification factor of 137 Cs content in complete product and this fact should be taken into account for forest cutting activities. (author)

  2. Shear accumulation as a means for evaluating risk of thromboembolic events in novel endovascular stent graft designs.

    Science.gov (United States)

    Suess, Taylor; Anderson, Joseph; Sherman, Andrea; Remund, Tyler; Pohlson, Kathryn; Mani, Gopinath; Gent, Stephen; Kelly, Patrick

    2017-06-01

    This study proposes to establish a simulation-based technique for evaluating shear accumulation in stent grafts and to use the technique to assess the performance of a novel branched stent graft system. Computational fluid dynamics models, with transient boundary conditions, particle injection, and rigid walls, simplifying assumptions were developed and used to evaluate the shear accumulation in various stent graft configurations with a healthy aorta as comparison. Shear streamlines are presented for the various configurations. Shear accumulation was also calculated for each configuration. The number of particles with shear accumulations >3.5 Pa-s for each configuration was compared with the shear accumulation values of commercially available mechanical aortic valves from the literature. The stent graft configuration with the diaphragm does have particles with shear accumulation >3.5 Pa-s. However, the percentage of particles with shear accumulation above 3.5 Pa-s is less than the two commercially available mechanical aortic valves, and more surprisingly, is smaller than in the healthy aorta. Copyright © 2016. Published by Elsevier Inc.

  3. Mitochondrial iron accumulation exacerbates hepatic toxicity caused by hepatitis C virus core protein

    Energy Technology Data Exchange (ETDEWEB)

    Sekine, Shuichi; Ito, Konomi; Watanabe, Haruna; Nakano, Takafumi [Laboratory of Biopharmaceutics, Graduate School of Pharmaceutical Sciences, Chiba University, 1-8-1 Inohana, Chuo-ku, Chiba 260-8675 (Japan); Moriya, Kyoji; Shintani, Yoshizumi; Fujie, Hajime; Tsutsumi, Takeya; Miyoshi, Hideyuki; Fujinaga, Hidetake; Shinzawa, Seiko; Koike, Kazuhiko [Department of Internal Medicine, Graduate School of Medicine, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8655 (Japan); Horie, Toshiharu, E-mail: t.horie@thu.ac.jp [Laboratory of Biopharmaceutics, Graduate School of Pharmaceutical Sciences, Chiba University, 1-8-1 Inohana, Chuo-ku, Chiba 260-8675 (Japan)

    2015-02-01

    Patients with long-lasting hepatitis C virus (HCV) infection are at major risk of hepatocellular carcinoma (HCC). Iron accumulation in the livers of these patients is thought to exacerbate conditions of oxidative stress. Transgenic mice that express the HCV core protein develop HCC after the steatosis stage and produce an excess of hepatic reactive oxygen species (ROS). The overproduction of ROS in the liver is the net result of HCV core protein-induced dysfunction of the mitochondrial respiratory chain. This study examined the impact of ferric nitrilacetic acid (Fe-NTA)-mediated iron overload on mitochondrial damage and ROS production in HCV core protein-expressing HepG2 (human HCC) cells (Hep39b cells). A decrease in mitochondrial membrane potential and ROS production were observed following Fe-NTA treatment. After continuous exposure to Fe-NTA for six days, cell toxicity was observed in Hep39b cells, but not in mock (vector-transfected) HepG2 cells. Moreover, mitochondrial iron ({sup 59}Fe) uptake was increased in the livers of HCV core protein-expressing transgenic mice. This increase in mitochondrial iron uptake was inhibited by Ru360, a mitochondrial Ca{sup 2+} uniporter inhibitor. Furthermore, the Fe-NTA-induced augmentation of mitochondrial dysfunction, ROS production, and cell toxicity were also inhibited by Ru360 in Hep39b cells. Taken together, these results indicate that Ca{sup 2+} uniporter-mediated mitochondrial accumulation of iron exacerbates hepatocyte toxicity caused by the HCV core protein. - Highlights: • Iron accumulation in the livers of patients with hepatitis C virus (HCV) infection is thought to exacerbate oxidative stress. • The impact of iron overload on mitochondrial damage and ROS production in HCV core protein-expressing cells were examined. • Mitochondrial iron uptake was increased in the livers of HCV core protein-expressing transgenic mice. • Ca{sup 2+} uniporter-mediated mitochondrial accumulation of iron exacerbates

  4. Hydrocarbon productivities in different Botryococcus strains: comparative methods in product quantification.

    Science.gov (United States)

    Eroglu, Ela; Okada, Shigeru; Melis, Anastasios

    2011-08-01

    Six different strains of the green microalgae Botryococcus belonging to the A-race or B-race, accumulating alkadiene or botryococcene hydrocarbons, respectively, were compared for biomass and hydrocarbon productivities. Biomass productivity was assessed gravimetrically upon strain growth in the laboratory under defined conditions. Hydrocarbon productivities were measured by three different and independent experimental approaches, including density equilibrium of the intact cells and micro-colonies, spectrophotometric analysis of hydrocarbon extracts, and gravimetric quantitation of eluted hydrocarbons. All three hydrocarbon-quantitation methods yielded similar results for each of the strains examined. The B-race microalgae Botryococcus braunii var. Showa and Kawaguchi-1 constitutively accumulated botryococcene hydrocarbons equivalent to 30% and 20%, respectively, of their overall biomass. The A-race microalgae Botryococcus braunii, varieties Yamanaka, UTEX 2441 and UTEX LB572 constitutively accumulated alkadiene hydrocarbons ranging from 14% to 13% and 10% of their overall biomass, respectively. Botryococcus sudeticus (UTEX 2629), a morphologically different green microalga, had the lowest hydrocarbon accumulation, equal to about 3% of its overall biomass. Results validate the density equilibrium and spectrophotometric analysis methods in the quantitation of botryococcene-type hydrocarbons. These analytical advances will serve in the screening and selection of B. braunii and of other microalgae in efforts to identify those having a high hydrocarbon content for use in commercial applications.

  5. Overexpression of snapdragon Delila (Del) gene in tobacco enhances anthocyanin accumulation and abiotic stress tolerance.

    Science.gov (United States)

    Naing, Aung Htay; Park, Kyeung Il; Ai, Trinh Ngoc; Chung, Mi Young; Han, Jeung Sul; Kang, Young-Wha; Lim, Ki Byung; Kim, Chang Kil

    2017-03-23

    Rosea1 (Ros1) and Delila (Del) co-expression controls anthocyanin accumulation in snapdragon flowers, while their overexpression in tomato strongly induces anthocyanin accumulation. However, little data exist on how Del expression alone influences anthocyanin accumulation. In tobacco (Nicotiana tabacum 'Xanthi'), Del expression enhanced leaf and flower anthocyanin production through regulating NtCHS, NtCHI, NtF3H, NtDFR, and NtANS transcript levels. Transgenic lines displayed different anthocyanin colors (e.g., pale red: T 0 -P, red: T 0 -R, and strong red: T 0 -S), resulting from varying levels of biosynthetic gene transcripts. Under salt stress, the T 2 generation had higher total polyphenol content, radical (DPPH, ABTS) scavenging activities, antioxidant-related gene expression, as well as overall greater salt and drought tolerance than wild type (WT). We propose that Del overexpression elevates transcript levels of anthocyanin biosynthetic and antioxidant-related genes, leading to enhanced anthocyanin production and antioxidant activity. The resultant increase of anthocyanin and antioxidant activity improves abiotic stress tolerance.

  6. The accumulation of sup(95m)Tc from sea water by juvenile lobsters (Homarus gammarus L.)

    International Nuclear Information System (INIS)

    Swift, D.J.

    1985-01-01

    The uptake and retention of technetium from sea water by juvenile lobsters, and the effects of moulting on these processes, has been studied using sup(95m)Tc as a tracer. Accumulation was rapid with whole body concentration factors of over 2000 being measured in some lobsters. Uptake was highest immediately before a moult; post-moult there was a fall in accumulation. No simple mathematical equation for technetium accumulation with time was found. The technetium concentration in the moulted exoskeleton increased with time of exposure of the lobsters but never exceeded 2% of the whole body value. The highest percentage of the whole body activity was found in the digestive gland; the green gland had the highest concentration factor. Technetium excretion, following 64 d of accumulation, could be expressed as an exponential rate of loss. The biological half-time was calculated as 53 d. Moulted exoskeletons from these lobsters contained approximately 0.6% of the day zero whole body activity. (author)

  7. On the calculation of soft phase space integral

    International Nuclear Information System (INIS)

    Zhu, Hua Xing

    2015-01-01

    The recent discovery of the Higgs boson at the LHC attracts much attention to the precise calculation of its production cross section in quantum chromodynamics. In this work, we discuss the calculation of soft triple-emission phase space integral, which is an essential ingredient in the recently calculated soft-virtual corrections to Higgs boson production at next-to-next-to-next-to-leading order. The main techniques used this calculation are method of differential equation for Feynman integral, and integration of harmonic polylogarithms.

  8. Estimation of Bio-Accumulation by a Group Contribution Method

    International Nuclear Information System (INIS)

    Belhachem, B.; Canselier, J. P.

    2009-01-01

    The majority of organic pollutants, after their dispersion in water then their ingestion, have a strong tendency to accumulate in greases. That is due to the hydrophobic character of these molecules. To have an idea on the capacity of a substance to accumulate in the alive beings according to their lipidic mass, the modeling of the pollutant behaviour was made by considering its partition coefficient between n-octanol (representing the lipidic mass) and water. Its knowledge represents a very significant information for the petrochemical and the pharmaceutical industries. To dissipate any doubt about confidence concerning the obtained results, it is considered useful to check the effectiveness of UNIFAC method on the monomethylbenzoic acid such as, for example, the 3-methylbenzoic acid whose n-octanol-water partition coefficient is already listed in the literature.The small deviations observed between the n-octanol-water partition coefficients listed in the literature and the one calculated according UNIFAC method encouraged us to apply it in order to predict the n-octanol-water partition coefficient of the dimethylbenzoic acid. (author)

  9. Metal accumulation by stream bryophytes, related to chemical speciation

    Energy Technology Data Exchange (ETDEWEB)

    Tipping, E. [Centre for Ecology and Hydrology, Lancaster Environment Centre, Library Avenue, Bailrigg, Lancaster LA1 4AP (United Kingdom)], E-mail: et@ceh.ac.uk; Vincent, C.D.; Lawlor, A.J.; Lofts, S. [Centre for Ecology and Hydrology, Lancaster Environment Centre, Library Avenue, Bailrigg, Lancaster LA1 4AP (United Kingdom)

    2008-12-15

    Metal accumulation by aquatic bryophytes was investigated using data for headwater streams of differing chemistry. The Windermere Humic Aqueous Model (WHAM) was applied to calculate chemical speciation, including competitive proton and metal interactions with external binding sites on the plants. The speciation modelling approach gives smaller deviations between observed and predicted bryophyte contents of Cu, Zn, Cd and Pb than regressions based on total filtered metal concentrations. If all four metals, and Ni, are considered together, the WHAM predictions are superior at the 1% level. Optimised constants for bryophyte binding by the trace metals are similar to those for humic substances and simple carboxylate ligands. Bryophyte contents of Na, Mg and Ca are approximately explained by binding at external sites, while most of the K is intracellular. Oxide phases account for some of the Al, and most of the Mn, Fe and Co. - Speciation modelling can be used to interpret the accumulation of Ni, Cu, Zn, Cd and Pb by bryophytes, supporting its use to quantify trace metal bioavailability in the field.

  10. Microbial accumulation of uranium

    International Nuclear Information System (INIS)

    Zhang Wei; Dong Faqin; Dai Qunwei

    2005-01-01

    The mechanism of microbial accumulation of uranium and the effects of some factors (including pH, initial uranium concentration, pretreatment of bacteria, and so on) on microbial accumulation of uranium are discussed briefly. The research direction and application prospect are presented. (authors)

  11. The Antiproton Accumulator and Collector and the discovery of the W & Z intermediate vector bosons

    CERN Document Server

    Chohan, Vinod

    2016-01-01

    The following sections are included: Preface ; Brief outline of the overall scheme for antiprotons of the SPS as a collider ; Antiproton production and accumulation ; The AA and AC storage rings ; Stochastic cooling and stacking ; Post-acceleration of antiprotons and beams for SPS Collider ; Proton test beams for the AA and AC from the PS ; The W and Z discoveries and the Nobel Prize ; Accumulator performance ; Acknowledgements and conclusions ; References

  12. The StreamCat Dataset: Accumulated Attributes for NHDPlusV2 Catchments (Version 2.1) for the Conterminous United States: PRISM Data

    Science.gov (United States)

    This dataset represents climate observations within individual, local NHDPlusV2 catchments and upstream, contributing watersheds. Attributes of the landscape layer were calculated for every local NHDPlusV2 catchment and accumulated to provide watershed-level metrics. (See Supplementary Info for Glossary of Terms) PRISM is a set of monthly, yearly, and single-event gridded data products of mean temperature and precipitation, max/min temperatures, and dewpoints, primarily for the United States. In-situ point measurements are ingested into the PRISM (Parameter elevation Regression on Independent Slopes Model) statistical mapping system. The PRISM products use a weighted regression scheme to account for complex climate regimes associated with orography, rain shadows, temperature inversions, slope aspect, coastal proximity, and other factors. (see Data Sources for links to NHDPlusV2 data and USGS Data) These data are summarized by local catchment and by watershed to produce local catchment-level and watershed-level metrics as a continuous data type (see Data Structure and Attribute Information for a description).

  13. Numerical model of total artificial heart hemodynamics and the effect of its size on stress accumulation.

    Science.gov (United States)

    Marom, Gil; Chiu, Wei-Che; Slepian, Marvin J; Bluestein, Danny

    2014-01-01

    The total artificial heart (TAH) is a bi-ventricular mechanical circulatory support device that replaces the heart in patients with end-stage congestive heart failure. The device acts as blood pump via pneumatic activation of diaphragms altering the volume of the ventricular chambers. Flow in and out of the ventricles is controlled by mechanical heart valves. The aim of this study is to evaluate the flow regime in the TAH and to estimate the thrombogenic potential during systole. Toward that goal, three numerical models of TAHs of differing sizes, that include the deforming diaphragm and the blood flow from the left chamber to the aorta, are introduced. A multiphase model with injection of platelet particles is employed to calculate their trajectories. The shear stress accumulation in the three models are calculated along the platelets trajectories and their probability density functions, which represent the `thrombogenic footprint' of the device are compared. The calculated flow regime successfully captures the mitral regurgitation and the flows that open and close the aortic valve during systole. Physiological velocity magnitudes are found in all three models, with higher velocities and increased stress accumulation predicted for smaller devices.

  14. REVIEW OF METHODOLOGIES FOR COSTS CALCULATING OF RUMINANTS IN SLOVAKIA

    Directory of Open Access Journals (Sweden)

    Zuzana KRUPOVÁ

    2012-09-01

    Full Text Available The objective of this work was to synthesise and analyse the methodologies and the biological aspects of the costs calculation in ruminants in Slovakia. According to literature, the account classification of cost items is most often considered for construction of costing formula. The costs are mostly divided into fixed (costs independent from volume of herd’s production and variable ones (costs connected with improvement of breeding conditions. Cost for feeds and beddings, labour costs, other direct costs and depreciations were found as the most important cost items in ruminants. It can be assumed that including the depreciations into costs of the basic herd takes into consideration the real costs simultaneously invested into raising of young animals in the given period. Costs are calculated for the unit of the main and by-products and their classification is influenced mainly by the type of livestock and production system. In dairy cows is usually milk defined as the main product, and by- products are live born calf and manure. The base calculation unit is kilogram of milk (basic herd of cows and kilogram of gain and kilogram of live weight (young breeding cattle. In suckler cows is a live-born calf the main product and manure is the by-product. The costs are mostly calculated per suckler cow, live-born calf and per kilogram of live weight of weaned calf. Similar division of products into main and by-products is also in cost calculation for sheep categories. The difference is that clotted cheese is also considered as the main product of basic herd in dairy sheep and greasy wool as the by-products in all categories. Definition of the base calculation units in sheep categories followed the mentioned classification. The value of a by-product in cattle and sheep is usually set according to its quantity and intra- plant price of the by-product. In the calculation of the costs for sheep and cattle the “structural ewe” and “structural cow

  15. Uncertainty of decay heat calculations originating from errors in the nuclear data and the yields of individual fission products

    International Nuclear Information System (INIS)

    Rudstam, G.

    1979-01-01

    The calculation of the abundance pattern of the fission products with due account taken of feeding from the fission of 235 U, 238 U, and 239 Pu, from the decay of parent nuclei, from neutron capture, and from delayed-neutron emission is described. By means of the abundances and the average beta and gamma energies the decay heat in nuclear fuel is evaluated along with its error derived from the uncertainties of fission yields and nuclear properties of the inddividual fission products. (author)

  16. The characteristics of biomass production, lipid accumulation and ...

    African Journals Online (AJOL)

    Glucose was the optimal carbon source for mixotrophic cultivation of C. vulgaris and the effects of glucose content on the alga growth under mixotrophic conditions were considerable because lower glucose content (1 g/l) promoted the production of biomass and photosynthetic pigments; higher glucose contents (>5 g/l) ...

  17. Accumulator ring lattice for the national spallation neutron source

    International Nuclear Information System (INIS)

    Gardner, C.J.; Lee, Y.Y.; Luccio, A.U.

    1997-01-01

    The Accumulator Ring for the proposed National Spallation Neutron Source (NSNS) is to accept a 1.03 millisecond beam pulse from a 1 GeV Proton Linac at a repetition rate of 60 Hz. For each beam pulse, 10 14 protons are to be accumulated via charge-exchange injection. A 295 nanosecond gap in the beam, maintained by an rf system, will allow for extraction to an external target for the production of neutrons by spallation. This paper describes the four-fold symmetric lattice that has been chosen for the ring. The lattice contains four long dispersion-free straight sections to accomodate injection, extraction, rf cavities, and beam scraping respectively. The four-fold symmetry allows for easy adjustment of the tunes and flexibility in the placement of correction elements, and ensures that potentially dangerous betatron structure resonances are avoided

  18. Calculations of standard-Higgs-boson production cross sections in e+e- collisions by means of a reasonable set of parameters

    International Nuclear Information System (INIS)

    Biyajima, M.; Shirane, K.; Terazawa, O.

    1987-01-01

    We calculate cross sections for production of the standard Higgs boson in e + e - collisions and compare our results with those of several authors. It is found that there are appreciable differences among them which can be attributed to the coupling constants used, α(0) ( = (1/137) and G/sub F/. We also observe that cross sections depend on the magnitudes of the total width of the Z particle. The use of a reasonable set of parameters in calculations is emphasized

  19. Enhanced saturated fatty acids accumulation in cultures of newly-isolated strains of Schizochytrium sp. and Thraustochytriidae sp. for large-scale biodiesel production.

    Science.gov (United States)

    Wang, Qiuzhen; Sen, Biswarup; Liu, Xianhua; He, Yaodong; Xie, Yunxuan; Wang, Guangyi

    2018-08-01

    Heterotrophic marine protists (Thraustochytrids) have received increasingly global attention as a renewable, sustainable and alternative source of biodiesel because of their high ability of saturated fatty acids (SFAs) accumulation. Yet, the influence of extrinsic factors (nutrients and environmental conditions) on thraustochytrid culture and optimal conditions for high SFAs production are poorly described. In the present study, two different thraustochytrid strains, Schizochytrium sp. PKU#Mn4 and Thraustochytriidae sp. PKU#Mn16 were studied for their growth and SFAs production profiles under various conditions (carbon, nitrogen, temperature, pH, KH 2 PO 4 , salinity, and agitation speed). Of the culture conditions, substrates (C and N) source and conc., temperature, and agitation speed significantly influenced the cell growth and SFAs production of both strains. Although both the strains were capable of growth and SFAs production in the broad range of culture conditions, their physiological responses to KH 2 PO 4 , pH, and salinity were dissimilar. Under their optimal batch culture conditions, peak SFAs productions of 3.3g/L and 2.2g/L with 62% and 49% SFAs contents (relative to total fatty acids) were achieved, respectively. The results of 5-L fed-batch fermentation under optimal conditions showed a nearly 4.5-fold increase in SFAs production (i.e., 7.5g/L) by both strains compared to unoptimized conditions. Of the two strains, the quality of biodiesel produced from the fatty acids of PKU#Mn4 met the biodiesel standard defined by ASTM6751. This study, to the knowledge of the authors, is the first comprehensive report of optimal fermentation conditions demonstrating enhanced SFAs production by strains belonging to two different thraustochytrid genera and provides the basis for large-scale biodiesel production. Copyright © 2018. Published by Elsevier B.V.

  20. The migration, accumulation and distribution of 59Fe in rice plants and soils

    International Nuclear Information System (INIS)

    Wang Yumin; Xu Shiming; Xu Guanren

    1990-07-01

    The 59 Fe is one of radionuclides in the waste water discharged from nuclear power plants. The accumulation and distribution of 59 Fe in rice plants at different growing stages and the accumulation and migration in soils of different textures were studied by using solution containing 59 FeCl 3 as a tracer. At the same contaminated activity, the distribution in the soils are discussed. According to the biological consequences caused by 59 Fe entering indirectly into agroecological environment, the possible methods for treatment and utilization of agricultural products are suggested

  1. Non-alcoholic fatty liver disease is associated with insulin resistance and lipid accumulation product in women with polycystic ovary syndrome.

    Science.gov (United States)

    Macut, D; Tziomalos, K; Božić-Antić, I; Bjekić-Macut, J; Katsikis, I; Papadakis, E; Andrić, Z; Panidis, D

    2016-06-01

    What are the most relevant factors associated with non-alcoholic fatty liver disease (NAFLD) in women with polycystic ovary syndrome (PCOS)? Insulin resistance (IR) and lipid accumulation product (LAP) are independently associated with NAFLD in PCOS. Obesity and IR are frequently present in both women with PCOS and subjects having NAFLD. The coexistence of PCOS and NAFLD might synergistically increase the risk for both type 2 diabetes (T2DM) and cardiovascular disease (CVD). LAP, calculated from waist circumference (WC) and triglycerides (TGs) concentrations [(WC-58) × TGs], has been shown to represent an integrated marker of cardiometabolic risk in women with PCOS. This cross-sectional study included 600 Caucasian women diagnosed with PCOS by the Rotterdam criteria between May 2008 and May 2013. The study was done at the university hospitals in Belgrade, Serbia and Thessaloniki, Greece. All subjects underwent anthropometric measurements and analyses of fasting blood glucose, insulin, lipids, total testosterone and SHBG, as well as liver tests (transaminases, γ-glutamyltransaminase, total bilirubin and alkaline phosphatase). Calculations for a NAFLD liver fat score (NAFLD-LFS) (with, accordingly, determination of metabolic syndrome and testing for T2DM) as well as homeostasis model assessment of IR (HOMA-IR), LAP as a marker of visceral adiposity, and free androgen index (FAI) were performed. We evaluated the prevance of NAFLD and analyzed associations of the above variables with NAFLD. NAFLD was more prevalent in patients with PCOS than in controls (50.6 versus 34.0%, respectively). Women with PCOS had higher readings for WC, LAP, insulin and HOMA-IR, total cholesterol and TGs than controls (P risk of complications while magnetic resonance spectroscopy does not provide any information regarding the presence of fibrosis and is not routinely available. Another possible limitation could be the measurement of total testosterone by radioimmunoassay, which can be

  2. Accumulation of contaminants of emerging concern in food crops-part 2: Plant distribution.

    Science.gov (United States)

    Hyland, Katherine C; Blaine, Andrea C; Higgins, Christopher P

    2015-10-01

    Arid agricultural regions often turn to using treated wastewater (reclaimed water) to irrigate food crops. Concerns arise, however, when considering the potential for persistent contaminants of emerging concern to accumulate into plants intended for human consumption. The present study examined the accumulation of a suite of 9 contaminants of emerging concern into 2 representative food crops, lettuce and strawberry, following uptake via the roots and subsequent distribution to other plant tissues. Calculating accumulation metrics (concentration factors) allowed for comparison of the compartmental affinity of each chemical for each plant tissue compartment. The root concentration factor was found to exhibit a positive linear correlation with the pH-adjusted octanol-water partition coefficient (DOW ) for the target contaminants of emerging concern. Coupled with the concentration-dependent accumulation observed in the roots, this result implies that accumulation of these contaminants of emerging concern into plant roots is driven by passive partitioning. Of the contaminants of emerging concern examined, nonionizable contaminants, such as triclocarban, carbamazepine, and organophosphate flame retardants displayed the greatest potential for translocation from the roots to above-ground plant compartments. In particular, the organophosphate flame retardants displayed increasing affinity for shoots and fruits with decreasing size/octanol-water partition coefficient (KOW ). Cationic diphenhydramine and anionic sulfamethoxazole, once transported to the shoots of the strawberry plant, demonstrated the greatest potential of the contaminants examined to be then carried to the edible fruit portion. © 2015 SETAC.

  3. Intensity of 137Cs accumulation by macromycetes of oak-hornbeam forests

    International Nuclear Information System (INIS)

    Orlov, A.A.; Kurbet, T.V.

    2005-01-01

    The intensity of 137 Cs accumulation by fruit bodies of macromycetes of 25 species were studied under conditions of fresh oak forests in oak-hornbeam forests of Podolsk Hills (Ukraine). It was found the intraspecific differences of average values of 137 Cs specific activity in mushrooms fruit bodies on the same forest plots were about 35 times and average values of transfer factor - about 45 times; the ranked row of mushroom species was build up according their average values. It was shown, the row →forest litter saprotrophes→humus sapritrophes→xylotrophes-sapritrophes - is formed according to intensity of 137 Cs accumulation in fruit bodies ecological-trophic groups of macromycete. Permissible levels for density of 137 Cs soil contamination to preserve edible mushrooms were calculated; and it was drawn a conclusion to the effect that studied species of mushrooms can be presented without any limits. (author)

  4. High-Affinity Accumulation of Chloroquine by Mouse Erythrocytes Infected with Plasmodium berghei

    Science.gov (United States)

    Fitch, Coy D.; Yunis, Norman G.; Chevli, Rekha; Gonzalez, Yolanda

    1974-01-01

    Washed erythrocytes infected with chloroquine-susceptible (CS) or with chloroquine-resistant (CR) P. berghei were used in model systems in vitro to study the accumulation of chloroquine with high affinity. The CS model could achieve distribution ratios (chloroquine in cells: chloroquine in medium) of 100 in the absence of substrate. 200—300 in the presence of 10 mM pyruvate or lactate, and over 600 in the presence of 1 mM glucose or glycerol. In comparable studies of the CR model, the distribution ratios were 100 in the absence of substrate and 300 or less in the presence of glucose or glycerol. The presence of lactate stimulated chloroquine accumulation in the CR model, whereas the presence of pyruvate did not. Lactate production from glucose and glycerol was undiminished in the CR model, and ATP concentrations were higher than in the CS model. Cold, iodoacetate, 2,4-dinitrophenol, or decreasing pH inhibited chloroquine accumulation in both models. These findings demonstrate substrate involvement in the accumulation of chloroquine with high affinity. In studies of the CS model, certain compounds competitively inhibited chloroquine accumulation, while others did not. This finding is attributable to a specific receptor that imposes structural constraints on the process of accumulation. For chloroquine analogues, the position and length of the side chain, the terminal nitrogen atom of the side chain, and the nitrogen atom in the quinoline ring are important determinants of binding to this receptor. PMID:4600044

  5. The FLUKA atmospheric neutrino flux calculation

    CERN Document Server

    Battistoni, G.; Montaruli, T.; Sala, P.R.

    2003-01-01

    The 3-dimensional (3-D) calculation of the atmospheric neutrino flux by means of the FLUKA Monte Carlo model is here described in all details, starting from the latest data on primary cosmic ray spectra. The importance of a 3-D calculation and of its consequences have been already debated in a previous paper. Here instead the focus is on the absolute flux. We stress the relevant aspects of the hadronic interaction model of FLUKA in the atmospheric neutrino flux calculation. This model is constructed and maintained so to provide a high degree of accuracy in the description of particle production. The accuracy achieved in the comparison with data from accelerators and cross checked with data on particle production in atmosphere certifies the reliability of shower calculation in atmosphere. The results presented here can be already used for analysis by current experiments on atmospheric neutrinos. However they represent an intermediate step towards a final release, since this calculation does not yet include the...

  6. Accumulation of carbonyls accelerates the formation of pentosidine, an advanced glycation end product: carbonyl stress in uremia.

    Science.gov (United States)

    Miyata, T; Ueda, Y; Yamada, Y; Izuhara, Y; Wada, T; Jadoul, M; Saito, A; Kurokawa, K; van Ypersele de Strihou, C

    1998-12-01

    Advanced glycation end product (AGE) formation is related to hyperglycemia in diabetes but not in uremia, because plasma AGE levels do not differ between diabetic and nondiabetic hemodialysis patients. The mechanism of this phenomenon remains elusive. Previously, it was suggested that elevation of AGE levels in uremia might result from the accumulation of unknown AGE precursors. The present study evaluates the in vitro generation of pentosidine, a well identified AGE structure. Plasma samples from healthy subjects and nondiabetic hemodialysis patients were incubated under air for several weeks. Pentosidine levels were determined at intervals by HPLC assay. Pentosidine rose to a much larger extent in uremic than in control plasma. Pentosidine yield, i.e., the change in pentosidine level between 0 and 4 wk divided by 28 d, averaged 0.172 nmol/ml per d in uremic versus 0.072 nmol/ml per d in control plasma (P aminoguanidine and OPB-9195, which inhibit the Maillard reaction, lowered pentosidine yield in both uremic and control plasma. When ultrafiltrated plasma was exposed to 2,4-dinitrophenylhydrazine, the yield of hydrazones, formed by interaction with carbonyl groups, was markedly higher in uremic than in control plasma. These observations strongly suggest that the pentosidine precursors accumulated in uremic plasma are carbonyl compounds. These precursors are unrelated to glucose or ascorbic acid, whose concentration is either normal or lowered in uremic plasma. They are also unrelated to 3-deoxyglucosone, a glucose-derived dicarbonyl compound whose level is raised in uremic plasma: Its addition to normal plasma fails to increase pentosidine yield. This study reports an elevated level of reactive carbonyl compounds ("carbonyl stress") in uremic plasma. Most have a lower than 5000 Da molecular weight and are thus partly removed by hemodialysis. Their effect on pentosidine generation can be inhibited by aminoguanidine or OPB-9195. Carbonyl stress might contribute to

  7. Benchmark calculation for water reflected STACY cores containing low enriched uranyl nitrate solution

    International Nuclear Information System (INIS)

    Miyoshi, Yoshinori; Yamamoto, Toshihiro; Nakamura, Takemi

    2001-01-01

    In order to validate the availability of criticality calculation codes and related nuclear data library, a series of fundamental benchmark experiments on low enriched uranyl nitrate solution have been performed with a Static Experiment Criticality Facility, STACY in JAERI. The basic core composed of a single tank with water reflector was used for accumulating the systematic data with well-known experimental uncertainties. This paper presents the outline of the core configurations of STACY, the standard calculation model, and calculation results with a Monte Carlo code and JENDL 3.2 nuclear data library. (author)

  8. Calculation of the electron trajectory for 200 kV self-shielded electron accelerator

    International Nuclear Information System (INIS)

    Wang Shuiqing

    2000-01-01

    In order to calculate the electron trajectory of 200 kV self-shielded electron accelerator, the electric field is calculated with a TRAJ program. In this program, following electron track mash points one by one, the electron beam trajectories are calculated. Knowing the effect of grid voltage on electron optics and gaining grid voltage focusing effect in the various energy grades, the authors have gained scientific basis for adjusting grid voltage, and also accumulated a wealth of experience for designing self-shielded electron accelerator or electron curtain in future

  9. Measurement of placental blood flow by the sup(113m)In accumulation method

    International Nuclear Information System (INIS)

    Olkkonen, H.; Suonio, S.

    1976-01-01

    The present work introduces the use of isotope In-113m in the assessment of placental blood flow. It is almost completely bound to plasma transferrin. Owing to this and its short half-life, In-113m introduces considerably slighter radiation dose to the fetus than Tc-99m. A typical tracer appearance curve is given and the In accumulation index is calculated. (M.S.)

  10. Cadmium uptake and speciation changes in the rhizosphere of cadmium accumulator and non-accumulator oilseed rape varieties

    Institute of Scientific and Technical Information of China (English)

    SU Dechun; XING Jianping; JIAO Weiping; WONG Woonchung

    2009-01-01

    Characteristics of cadmium (Cd) uptake kinetics and distribution of Cd speciation in the rhizosphere for Cd accumulator and non-accumulator oilseed rape varieties were investigated under nutrient solution and rhizobox soil culture conditions.The results showed that the maximal influx (Vmax) for Cd2+ and Km were significantly different for the two oilseed rape varieties.The value of Vmax for Cd accumulator oilseed rape Zhucang Huazi was two-fold greater than that for oilseed rape Chuangyou II-93.The exchangeable Cd concentration in the rhizosphere was significantly lower than in non-rhizospheric soils supplemented with Cd as CdSO4 for both the varieties.Carbonate-bound Cd in the rhizosphere of Cd accumulator oilseed rape was significantly higher than that in the rhizosphere of non-accumulator oilseed rape and non-rhizospheric soil.Cd accumulator oilseed rape had a higher Cd2+ affinity and more ability to uptake insoluble Cd in the soil than the non-accumulator oilseed rape.

  11. Accumulation, sources and health risks of trace metals in elevated geochemical background soils used for greenhouse vegetable production in southwestern China.

    Science.gov (United States)

    Zhang, Haidong; Huang, Biao; Dong, Linlin; Hu, Wenyou; Akhtar, Mohammad Saleem; Qu, Mingkai

    2017-03-01

    Greenhouse vegetable cultivation with substantive manure and fertilizer input on soils with an elevated geochemical background can accumulate trace metals in soils and plants leading to human health risks. Studies on trace metal accumulation over a land use shift duration in an elevated geochemical background scenario are lacking. Accumulation characteristics of seven trace metals in greenhouse soil and edible plants were evaluated along with an assessment of the health risk to the consumers. A total of 118 greenhouse surface soils (0-20cm) and 30 vegetables were collected from Kunming City, Yunnan Province, southwestern China, and analyzed for total Cd, Pb, Cu, Zn, As, Hg, and Cr content by ICP-MS and AFS. The trace metals were ordered Cu>Cd>Hg>Zn>Pb>As>Cr in greenhouse soils accumulation level, and the geo-accumulation index suggested the soil more severely polluted with Cd, Cu, Hg and Zn. The greenhouse and open-field soils had significant difference in Cd, Cr and Zn. The duration of shift from paddy to greenhouse land-use significantly influenced trace metal accumulation with a dramatic change during five to ten year greenhouse land-use, and continuous increase of Cd and Hg. A spatial pattern from north to south for Cd and Hg and a zonal pattern for Cu and Zn were found. An anthropogenic source primarily caused trace metal accumulation, where the principal component analysis/multiple linear regression indicated a contribution 61.2%. While the assessment showed no potential risk for children and adults, the hazard health risks index was greater than one for adolescents. The extended duration of land use as greenhouses caused the trace metal accumulation, rotation in land use should be promoted to reduce the health risks. Copyright © 2016. Published by Elsevier Inc.

  12. Transverse beam stability measurement and analysis for the SNS accumulator ring

    Energy Technology Data Exchange (ETDEWEB)

    Xie, Zaipeng [University of Wisconsin-Madison, Madison, WI 53706-1691 (United States); Deibele, Craig, E-mail: deibele@ornl.gov [Oak Ridge National Laboratory, PO BOX 2008 MS6483, Oak Ridge, TN 37831-6461 (United States); Schulte, Michael J.; Hu, Yu-Hen [University of Wisconsin-Madison, Madison, WI 53706-1691 (United States)

    2015-07-11

    A field-programmable gate array (FPGA)-based transverse feedback damper system was implemented in the Spallation Neutron Source (SNS) accumulator ring with the intention to stabilize the electron–proton (e–p) instability in the frequency range of 1–300 MHz. The transverse feedback damper could also be used as a diagnostic tool by measuring the beam transfer function (BTF). An analysis of the BTF measurements provides the stability diagram for the production beam at SNS. This paper describes the feedback damper system and its setup as the BTF diagnostic tool. Experimental BTF results are presented and beam stability is analyzed by use of the BTF measurements for the SNS accumulator ring.

  13. Transverse beam stability measurement and analysis for the SNS accumulator ring

    International Nuclear Information System (INIS)

    Xie, Zaipeng; Deibele, Craig; Schulte, Michael J.; Hu, Yu-Hen

    2015-01-01

    A field-programmable gate array (FPGA)-based transverse feedback damper system was implemented in the Spallation Neutron Source (SNS) accumulator ring with the intention to stabilize the electron–proton (e–p) instability in the frequency range of 1–300 MHz. The transverse feedback damper could also be used as a diagnostic tool by measuring the beam transfer function (BTF). An analysis of the BTF measurements provides the stability diagram for the production beam at SNS. This paper describes the feedback damper system and its setup as the BTF diagnostic tool. Experimental BTF results are presented and beam stability is analyzed by use of the BTF measurements for the SNS accumulator ring

  14. Effect of Free Nitrous Acid on Nitrous Oxide Production and Denitrifying Phosphorus Removal by Polyphosphorus-Accumulating Organisms in Wastewater Treatment

    Directory of Open Access Journals (Sweden)

    Zhijia Miao

    2018-01-01

    Full Text Available The inhibition of free nitrous acid (FNA on denitrifying phosphorus removal has been widely reported for enhanced biological phosphorus removal; however, few studies focus on the nitrous oxide (N2O production involved in this process. In this study, the effects of FNA on N2O production and anoxic phosphorus metabolism were investigated using phosphorus-accumulating organisms (PAOs culture highly enriched (91±4% in Candidatus Accumulibacter phosphatis. Results show that the FNA concentration notably inhibited anoxic phosphorus metabolism and phosphorus uptake. Poly-β-hydroxyalkanoate (PHA degradation was completely inhibited when the FNA concentration was approximately 0.0923 mgHNO2-N/L. Higher initial FNA concentrations (0.00035 to 0.0103 mgHNO2-N/L led to more PHA consumption/TN (0.444 to 0.916 mmol-C/(mmol-N·gVSS. Moreover, it was found that FNA, rather than nitrite and pH, was likely the true inhibitor of N2O production. The highest proportion of N2O to TN was 78.42% at 0.0031 mgHNO2-N/L (equivalent to 42.44 mgNO2-N/L at pH 7.5, due to the simultaneous effects of FNA on the subsequent conversion of NO2 into N2O and then into N2. The traditional nitrite knee point can only indicate the exhaustion of nitrite, instead of the complete removal of TN.

  15. Calculation model for predicting concentrations of radioactive corrostion products in the primary coolant of boiling water reactors

    International Nuclear Information System (INIS)

    Uchida, S.; Kikuchi, M.; Asakura, Y.; Yusa, H.; Ohsumi, K.

    1978-01-01

    A calculation model was developed to predict the shutdown dose rate around the recirculation pipes and their components in boiling water reactors (BWRs) by simulating the corrosion product transport in primary cooling water. The model is characterized by separating cobalt species in the water into soluble and insoluble materials and then calculating each concentration using the following considerations: (1) Insoluble cobalt (designated as crud cobalt is deposited directly on the fuel surface, while soluble cobalt (designated as ionic cobalt) is adsorbed on iron oxide deposits on the fuel surface. (2) Cobalt-60 activated on the fuel surface is dissolved in the water in an ionic form, and some is released with iron oxide as crud. The model can follow the reduction of 60 Co in the primary cooling water caused by the control of the iron feed rate into the reactor, which decreases the iron oxide deposits on the fuel surface and then reduces the cobalt adsorption rate. The calculated results agree satisfactorily with the measurements in several BWR plants

  16. The StreamCat Dataset: Accumulated Attributes for NHDPlusV2 (Version 2.1) Catchments for the Conterminous United States: PRISM Normals Data

    Science.gov (United States)

    This dataset represents climate observations within individual, local NHDPlusV2 catchments and upstream, contributing watersheds. Attributes of the landscape layer were calculated for every local NHDPlusV2 catchment and accumulated to provide watershed-level metrics. (See Supplementary Info for Glossary of Terms) PRISM is a set of monthly, yearly, and single-event gridded data products of mean temperature and precipitation, max/min temperatures, and dewpoints, primarily for the United States. In-situ point measurements are ingested into the PRISM (Parameter elevation Regression on Independent Slopes Model) statistical mapping system. The PRISM products use a weighted regression scheme to account for complex climate regimes associated with orography, rain shadows, temperature inversions, slope aspect, coastal proximity, and other factors. (see Data Sources for links to NHDPlusV2 data and USGS Data) These data are summarized by local catchment and by watershed to produce local catchment-level and watershed-level metrics as a continuous data type (see Data Structure and Attribute Information for a description).

  17. 9 CFR 124.20 - Patent term extension calculation.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Patent term extension calculation. 124... OF AGRICULTURE VIRUSES, SERUMS, TOXINS, AND ANALOGOUS PRODUCTS; ORGANISMS AND VECTORS PATENT TERM RESTORATION Regulatory Review Period § 124.20 Patent term extension calculation. (a) As provided in 37 CFR 1...

  18. Effects of lead accumulation on the Azolla caroliniana-Anabaena association.

    Science.gov (United States)

    Roberts, Anne E; Boylen, Charles W; Nierzwicki-Bauer, Sandra A

    2014-04-01

    The effect of lead accumulation on photopigment production, mineral nutrition, and Anabaena vegetative cell size and heterocyst formation in Azolla caroliniana was investigated. Plants were exposed to 0, 1, 5, 10, and 20 mg L(-1) lead acetate for ten days. Lead accumulation increased when plants were treated with higher lead concentrations. Results revealed a statistically significant decline in total chlorophyll, chlorophyll a, chlorophyll b, and carotenoids in 5, 10, and 20 mg Pb L(-1) treatment groups as compared to plants with 0 or 1 mg Pb L(-1) treatments. No statistically significant change in anthocyanin production was observed. Calcium, magnesium, and zinc concentrations in plants decreased in increasing treatment groups, whereas sodium and potassium concentrations increased. Nitrogen and carbon were also found to decrease in plant tissue. Anabaena vegetative cells decreased in size and heterocyst frequency declined rapidly in a Pb dose-dependent manner. These results indicate that, while A. caroliniana removes lead from aqueous solution, the heavy metal causes physiological and biochemical changes by impairing photosynthesis, changing mineral nutrition, and impeding the growth and formation of heterocysts of the symbiotic cyanobacteria that live within leaf cavities of the fronds. Copyright © 2014. Published by Elsevier Inc.

  19. Antiproton production

    International Nuclear Information System (INIS)

    Allaby, J.V.

    1984-01-01

    The basic definitions used in the physics literature on particle production are reviewed. The data on anti p production are interpreted in order to provide an estimate of the yield of anti p's from typical target at the antiproton accumulator, including the effects of re-absorption in the target. (orig.)

  20. Guidelines for Waste Accumulation Areas (WAAs)

    International Nuclear Information System (INIS)

    1991-07-01

    The purpose of this document is to set conditions for establishing and maintaining areas for the accumulation of hazardous waste at LBL. Areas designed for accumulation of these wastes in quantities greater than 100 kg (220 lb) per month of solid waste or 55 gallons per month of liquid waste are called Waste Accumulation Areas (WAAs). Areas designed for accumulation of wastes in smaller amounts are called Satellite Accumulation Areas (SAAs). This document provides guidelines for employee and organizational responsibilities for WAAs; constructing a WAA; storing waste in a WAA; operating and maintaining a WAA, and responding to spills in a WAA. 4 figs

  1. Accumulation of potassium in scala vestibuli perilymph of the mammalian cochlea.

    Science.gov (United States)

    Salt, A N; Ohyama, K

    1993-01-01

    Movements of potassium (K+) were monitored during perfusion of either the scala tympani (ST) or the scala vestibuli (SV) of the guinea pig cochlea with a solution containing 15 mmol/LK+. A highly asymmetric clearance of K+ was observed, with K+ rapidly being taken up from the ST and allowed to accumulate in the SV. Under some conditions the SV K+ concentration could exceed that in the perfused ST. These observations are believed to result from the distortion of passive K+ diffusion by the high circulating current of K+ that is part of the transduction process. Calculations are presented to demonstrate that circulating fluxes are of sufficient magnitude to generate the results observed. The high rate of circulating K+ current is probably also responsible for the difference in physiologic K+ concentration between the ST and SV, in which the ST perilymph K+ concentration is typically found to be half that of the SV. A clearance of K+ from the ST and its eventual accumulation in the SV could play a role in how the ear responds to abnormal ion concentrations, such as may occur in Meniere's disease. It is proposed that an accumulation of K+ in the SV would result in vestibular dysfunction that might contribute to the vestibular symptoms of the disease.

  2. Biota-Sediment Accumulation Factor Data

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Biota-Sediment Accumulation Factor contains approximately 20,000 biota-sediment accumulation factors (BSAFs) from 20 locations (mostly Superfund sites) for...

  3. UV irradiation promotes the accumulation of triglyceride in Lipomyces lipofer

    International Nuclear Information System (INIS)

    Konno, A.; Suzuki, Y.; Ogawa, T.; Taniuchi, T.

    2009-01-01

    Yeasts of the genus Lipomyces are known as fat yeasts, and they store large amounts of lipids. Because the major lipid produced by Lipomyces is triglyceride, which can be used as a food and energy resource, the control of lipid production by Lipomyces sp. is an important issue. Here we report the effects of UV irradiation on lipid production in Lipomyces lipofer cells. UV irradiation (315-400 nm) led to a 4-fold increase in the amount of triglyceride per cell. We discovered a novel phenomenon, that UV irradiation promotes triglyceride accumulation in L. lipofer. (author)

  4. Accumulating trade costs and competitiveness in global value chains

    OpenAIRE

    Diakantoni, Antonia; Escaith, Hubert; Roberts, Michael; Verbeet, Thomas

    2017-01-01

    Trade costs such as applied tariffs, transportation and insurance costs are amplified as they pass through the multiple production steps associated with modern supply chains. This so-called "cascade effect" arises since trade costs accumulate as intermediate goods are imported and then re-exported further downstream, going through different processing nodes before reaching the final consumer. Moreover, the financial impact of these trade costs is magnified in the "trade in tasks" rationale wh...

  5. CALCULATIONS OF DOUBLE IMPURITY DIFFUSION IN INTEGRATED CIRCUIT PRODUCTION

    Directory of Open Access Journals (Sweden)

    V. A. Bondarev

    2005-01-01

    Full Text Available Analytical formulae for calculating simultaneous diffusion of two impurities in silicon are presented. The formulae are based on analytical solutions of diffusion equations that have been obtained for the first time by the author while using some special mathematical functions. In contrast to usual formal mathematical approaches, new functions are determined in the process of investigation of real physical models. Algorithms involve some important relations from thermodynamics of irreversible processes and also variational thermodynamic functionals that were previously obtained by the author for transfer processes. Calculations considerably reduce the time required for development of new integrated circuits. 

  6. 47 CFR 32.3100 - Accumulated depreciation.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Accumulated depreciation. 32.3100 Section 32... Accumulated depreciation. (a) This account shall include the accumulated depreciation associated with the... with depreciation amounts concurrently charged to Account 6561, Depreciation expense—telecommunications...

  7. Coefficients of distribution and accumulation of K, Rb, Cs and 137Cs in the intensive poultry breeding cycle

    International Nuclear Information System (INIS)

    Djuric, G.; Ajdacic, N.; Institut za Nuklearne Nauke Boris Kidric, Belgrade

    1984-01-01

    The concentration of K,Rb,Cs and the activity level of Cs-137 in samples from the intensive poultry breeding cycle (feed, meat, eggs), under the condition of chronic alimentary contamination is presented. Concentrations of Cs and Rb were determined by non-destructive neutron activation analysis, concentration of K by atomic absorption flame photometry and activity of Cs-137 by gamma spectrometric analysis. On the basis of these results, coefficients of distribution and accumulation were calculated. The distribution coefficients of the analysed stable isotopes in meat have values close to 1, whereas for various parts of egg these coefficients vary between 0.5 and 1.5. Significant differences in Cs-137 distribution in various parts of egg were established. The values of accumulation coefficients indicate that all analysed elements selectively accumulate in the meat of young birds (broilers), and Cs-137 accumulates in the egg white as well. (orig.)

  8. Reactivity effects of fission product decay in PWRs

    International Nuclear Information System (INIS)

    Aragones, J.M.; Ahnert, C.

    1988-01-01

    The purpose of the work reported in this paper is to analyze the effects of fission product chains with radioactive decay on the reactivity in pressurized water reactor (PWR) cores, calculating their accumulation and absorption rates along fuel burnup at continuous operation and after shutdown periods extending from 1 day to a few months. The authors PWR version of the WIMS-D4 code is first used to obtain the individual number densities, absorption rates, and averaged cross sections for every nuclide of the fission product chains with significant decay rates, as a function of fuel burnup at continuous irradiation. Next, by an auxiliary ad hoc code, these data, have been processed together with the required one for fissile nuclides and boron, also taken from WIMS at each burnup step, to calculate the average or effective values relevant for the analysis and the decay and change in overall absorption after several shutdown times. (1) The reactivity effect of fission product decay changes significantly with the shutdown time. The maximum absorption increase by decay is reached in ∼ 10 days' shutdown. (2) The dependence with fuel type, enrichment, and burnup is slight, but the change with previous power density is nearly linear, which might be significant after coast-down in previous cycles. (3) For long shutdown periods, the overall reactivity effect of decay in the three fission product chains considered is much less than if only the samarium peak due to 149 Nd is considered

  9. Production of poly-beta-hydroxybutyric acid by microorganisms accumulated from river water using a two-stage perfusion culture system.

    Science.gov (United States)

    Morimoto, T; Tashiro, F; Nagashima, H; Nishizawa, K; Nagata, F; Yokogawa, Y; Suzuki, T

    2000-01-01

    The perfusion culture system using a shaken ceramic membrane flask (SCMF) was employed to accumulate microorganisms separated from river water and to produce poly-beta-hydroxybutyric acid (PHB). Using a two-step culture method with a single SCMF, river microorganisms were cultured by separately feeding four representative carbon sources, n-propanol, lactic acid, methanol, and formic acid. After 140 h culture, the cell concentration and PHB content respectively reached 43 g/l and 35% when a propanol medium was fed. Using a two-stage perfusion culture with twin SCMFs, the seed cell mass was increased in the first SCMF and then supplied to the second flask for PHB production. As a consequence, the cellular PHB content rose to 51% in the second SCMF, while the cell concentration gradually increased to 25 g/l after 175 h perfusion culture. These results demonstrated the utility of the two-stage perfusion culture system for developing a cheap means of producing PHB coincident with wastewater treatment.

  10. Geomorphic influences on the contribution of vegetation to soil C accumulation and accretion in Spartina alterniflora marshes

    Directory of Open Access Journals (Sweden)

    T. Elsey-Quirk

    2018-01-01

    Full Text Available Salt marshes are important hotspots of long-term belowground carbon (C storage, where plant biomass and allochthonous C can be preserved in the soil for thousands of years. However, C accumulation rates, as well as the sources of C, may differ depending on environmental conditions influencing plant productivity, allochthonous C deposition, and C preservation. For this study, we examined the relationship between belowground root growth, turnover, decay, above- and belowground biomass, and previously reported longer-term rates of total, labile, and refractory organic C accumulation and accretion in Spartina alterniflora-dominated marshes across two mid-Atlantic, US estuaries. Tidal range, long-term rates of mineral sedimentation, C accumulation, and accretion were higher and salinities were lower in marshes of the coastal plain estuary (Delaware Bay than in the coastal lagoon (Barnegat Bay. We expected that the conditions promoting high rates of C accumulation would also promote high plant productivity and greater biomass. We further tested the influence of environmental conditions on belowground growth (roots + rhizomes, decomposition, and biomass of S. alterniflora. The relationship between plant biomass and C accumulation rate differed between estuaries. In the sediment-limited coastal lagoon, rates of total, labile, and refractory organic C accumulation were directly and positively related to above- and belowground biomass. Here, less flooding and a higher mineral sedimentation rate promoted greater above- and belowground biomass and, in turn, higher soil C accumulation and accretion rates. In the coastal plain estuary, the C accumulation rate was related only to aboveground biomass, which was positively related to the rate of labile C accumulation. Soil profiles indicated that live root and rhizome biomass was positively associated with labile C density for most marshes, yet high labile C densities below the live root zone and in

  11. Comparison of methods for estimating carbon in harvested wood products

    International Nuclear Information System (INIS)

    Claudia Dias, Ana; Louro, Margarida; Arroja, Luis; Capela, Isabel

    2009-01-01

    There is a great diversity of methods for estimating carbon storage in harvested wood products (HWP) and, therefore, it is extremely important to agree internationally on the methods to be used in national greenhouse gas inventories. This study compares three methods for estimating carbon accumulation in HWP: the method suggested by Winjum et al. (Winjum method), the tier 2 method proposed by the IPCC Good Practice Guidance for Land Use, Land-Use Change and Forestry (GPG LULUCF) (GPG tier 2 method) and a method consistent with GPG LULUCF tier 3 methods (GPG tier 3 method). Carbon accumulation in HWP was estimated for Portugal under three accounting approaches: stock-change, production and atmospheric-flow. The uncertainty in the estimates was also evaluated using Monte Carlo simulation. The estimates of carbon accumulation in HWP obtained with the Winjum method differed substantially from the estimates obtained with the other methods, because this method tends to overestimate carbon accumulation with the stock-change and the production approaches and tends to underestimate carbon accumulation with the atmospheric-flow approach. The estimates of carbon accumulation provided by the GPG methods were similar, but the GPG tier 3 method reported the lowest uncertainties. For the GPG methods, the atmospheric-flow approach produced the largest estimates of carbon accumulation, followed by the production approach and the stock-change approach, by this order. A sensitivity analysis showed that using the ''best'' available data on production and trade of HWP produces larger estimates of carbon accumulation than using data from the Food and Agriculture Organization. (author)

  12. Reply to Nicholson's comment on "Consistent calculation of aquatic gross production from oxygen triple isotope measurements" by Kaiser (2011

    Directory of Open Access Journals (Sweden)

    J. Kaiser

    2012-08-01

    Full Text Available The comment by Nicholson (2011a questions the "consistency" of the "definition" of the "biological end-member" used by Kaiser (2011a in the calculation of oxygen gross production. "Biological end-member" refers to the relative oxygen isotope ratio difference between photosynthetic oxygen and Air-O2 (abbreviated 17δP and 18δP for 17O/16O and 18O/16O, respectively. The comment claims that this leads to an overestimate of the discrepancy between previous studies and that the resulting gross production rates are "30% too high". Nicholson recognises the improved accuracy of Kaiser's direct calculation ("dual-delta" method compared to previous approximate approaches based on 17O excess (17Δ and its simplicity compared to previous iterative calculation methods. Although he correctly points out that differences in the normalised gross production rate (g are largely due to different input parameters used in Kaiser's "base case" and previous studies, he does not acknowledge Kaiser's observation that iterative and dual-delta calculation methods give exactly the same g for the same input parameters (disregarding kinetic isotope fractionation during air-sea exchange. The comment is based on misunderstandings with respect to the "base case" 17δP and 18δP values. Since direct measurements of 17δP and 18δPdo not exist or have been lost, Kaiser constructed the "base case" in a way that was consistent and compatible with literature data. Nicholson showed that an alternative reconstruction of 17δP gives g values closer to previous studies. However, unlike Nicholson, we refrain from interpreting either reconstruction as a benchmark for the accuracy of g. A number of publications over the last 12 months

  13. Metabolic Conversion of l-Ascorbic Acid to Oxalic Acid in Oxalate-accumulating Plants 1

    Science.gov (United States)

    Yang, Joan C.; Loewus, Frank A.

    1975-01-01

    l-Ascorbic acid-1-14C and its oxidation product, dehydro-l-ascorbic acid, produced labeled oxalic acid in oxalate-accumulating plants such as spinach seedlings (Spinacia oleracea) and the detached leaves of woodsorrel (Oxalis stricta and O. oregana), shamrock (Oxalis adenopylla), and begonia (Begonia evansiana). In O. oregana, conversion occurred equally well in the presence or absence of light. This relationship between l-ascorbic acid metabolism and oxalic acid formation must be given careful consideration in attempts to explain oxalic accumulation in plants. PMID:16659288

  14. The effect of energy substrates on PHB accumulation of Acidiphilium cryptum DX1-1.

    Science.gov (United States)

    Xu, Ai-ling; Xia, Jin-lan; Song, Zhi-wen; Jiang, Peng; Xia, Yan; Wan, Min-xi; Zhang, Rui-yong; Yang, Yi; Liu, Ke-ke

    2013-09-01

    The effect of glucose and elemental sulfur on the growth and PHB accumulation of Acidiphilium cryptum DX1-1 was investigated. Meanwhile, the differential expressions of 19 genes related with PHB accumulation, sulfur metabolism and carbon fixed in heterotrophy, phytotrophy and mixotrophy were studied by RT-qPCR. The results showed that strain DX1-1 could accumulate PHB with sulfur as the energy substance and atmospheric CO2 as carbon resource. Glucose could improve the growth of strain DX1-1 cultured in medium with sulfur as the energy substance, and almost all the key enzyme-encoding genes related with PHB, sulfur metabolism and carbon fixed were basically up-regulated. PHB polymerase (Arcy_3030), ribulose-bisphosphate carboxylase (Acry_0825), ribulose-phosphate-epimerase (Acry_0022), and cysteine synthase A (Acry_2560) played important role in PHB accumulation, the modified expression of which could influence the PHB yield. With CO2 as carbon resource, the main initial substance of PHB accumulation for strain DX1-1 was acetyl-CoA, instead of acetate with the glucose as the carbon resource. Because of accumulating PHB by fixed atmospheric CO2 while independent of light, A. cryptum DX1-1 may have specifically potential in production of PHB.

  15. MARRIAGE AND MEN’S WEALTH ACCUMULATION IN THE UNITED STATES, 1860-1870

    Science.gov (United States)

    HONG, SOK CHUL

    2013-01-01

    This paper explores how changes in marital status affected men’s wealth accumulation in mid-nineteenth-century America, using a longitudinal sample of Union Army veterans linked to the 1860 and 1870 census manuscript schedules. Controlling for the endogeneity of wealth and marital selection, this paper provides strong evidence that marriage had positive effects on men’s wealth accumulation, whereas ending a marriage had negative effects. The estimated wealth premium on married men is about 60 percent per marital year. This substantial wealth premium is closely related to wives’ specializing in household production, and farmers and craftsmen economically benefited from the unpaid labor of their wives. PMID:24058226

  16. Prospects of using algae in biofuel production

    Directory of Open Access Journals (Sweden)

    Y. I. Maltsev

    2017-08-01

    Full Text Available The development of industry, agriculture and the transport sector is associated with the use of various energy sources. Renewable energy sources, including biofuels, are highly promising in this respect. As shown by a number of scientific studies, a promising source for biofuel production that would meet modern requirements may be algal biomass. After activation of the third generation biodiesel production it was assumed that the algae would become the most advantageous source, because it is not only able to accumulate significant amounts of lipids, but could reduce the of agricultural land involved in biofuel production and improve air quality by sequestering CO2. However, a major problem is presented by the cost of algae biomass cultivation and its processing compared to the production of biodiesel from agricultural crops. In this regard, there are several directions of increasing the efficiency of biodiesel production from algae biomass. The first direction is to increase lipid content in algae cells by means of genetic engineering. The second direction is connected with the stimulation of increased accumulation of lipids by stressing algae. The third direction involves the search for new, promising strains of algae that will be characterized by faster biomass accumulation rate, higher content of TAG and the optimal proportions of accumulated saturated and unsaturated fatty acids compared to the already known strains. Recently, a new approach in the search for biotechnologically valuable strains of algae has been formed on the basis of predictions of capacity for sufficient accumulation of lipids by clarifying the evolutionary relationships within the major taxonomic groups of algae. The outcome of these studies is the rapid cost reduction of biofuel production based on algae biomass. All this emphasizes the priority of any research aimed at both improving the process of production of biofuels from algae, and the search for new sources for