Overview of current status of SLR production and uses in Japan and other Asian countries

International Nuclear Information System (INIS)

Iio, M.

1985-01-01

The current status of short-lived radionuclide (SLR) production and use in Japan and other Asian countries is reviewed. The activities of six cyclotrons for medical use in Asia (except Japan) and Australia are reported. In Japan 10 dedicated medical cyclotrons were installed by 1983. Even though SLR application in Japan is in the cradle stage and is limited to only a few institutions, an analysis of these applications indicates the high efficacy of the dedicated small cyclotrons as compared with large, multipurpose cyclotrons. Because of the lack of high-energy commercial cyclotrons by 1982, a satisfactory iodine-123 supply of labeling quality has been limited. However, since two of the three medical cyclotron manufacturers and more than three positron camera producers are located there, Japan has high potential for the routine practice of nuclear medicine

A review on the current status and production technology for {sup 188}W-{sup 188}Re generator system

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, R. A.; Han, H. S.; Cho, W. K.; Park, U. J.; Kim, Y. M

1998-11-01

The current status of {sup 188}W-{sup 188}Re generator production technology were reviewed in PART 1. Main interests were given to the aspects of {sup 188}W reactor production, irradiated targets reprocessing and generator loading technologies, such as alumina type and gel type generators. In order to develop the more convenient and advanced {sup 188}W-{sup 188}Re generator, further studies must be carried out to get the precise evaluation of production and burn-up cross section of {sup 188}W, the more easily realizable generator loading procedure, and also to optimize the column and generator design to compensate the deterioration of generator performance because of parent radionuclide decay. By irradiation of {sup 186}W enriched sample, {sup 188}W-{sup 188}Re generator production experiments were performed to evaluate the possibility of {sup 188}W-{sup 188}Re generator production using HANARO, and PART 2 describes about the experiments. The experimental results shows the possibility of practical {sup 188}W-{sup 188}Re generator production using of low-specific activity {sup 188}W produced in HANARO. (author). 79 refs., 4 tabs., 26 figs.

Current status of chirality in agrochemicals.

Science.gov (United States)

Jeschke, Peter

2018-04-27

The agrochemical industry is continuously searching for new pesticides to develop products with optimal efficacy, lower application rates in the field, increased selectivity, favorable toxicological and environmental safety, enhanced user friendliness and better economic viability. One strategy to achieve these ambitious goals makes use of the unique properties of molecules containing asymmetric centers. In the past, many natural products and their congeners have been a source of inspiration for designing new active ingredients, and the molecular structure of the resulting molecules have become increasingly complex. 30% contain fragments with asymmetric centers. However, despite the enormous progress that has been made in catalytic asymmetric processes over the last decade, only few agrochemicals are produced in enantiomerically pure or enriched form on an industrial scale. Since 2007, around 43% of the 44 launched products (insecticides, acaricides, fungicides, nematicides, and herbicides) contain one or more asymmetric centers in the molecule (≈ 47 %) and most of them were launched as racemic mixtures of enantiomers or diastereomers. This review gives an overview of the current status of chiral agrochemicals launched over the past 10 years and describes the inherently connected challenges of modern agricultural chemistry by managing important aspects resulting from stereochemistry of these innovative products. This article is protected by copyright. All rights reserved.

Current status and some aspects of the future energy strategy

International Nuclear Information System (INIS)

Antic, D. P.; Sokcic-Kostic, M. S. . E-mail address of corresponding author: dragon@vin.bg.ac.yu; Antic, D.)

2005-01-01

Current status of the energy production and of the energy sources in the world, European Union, Serbia and Montenegro and the Balkan states is analyzed. Some trends in the energy consumption and productions in some European states are analyzed. Some problems of the Serbia and Montenegro energy production system are compared with situation in neighbor states, Germany, and European Union. At present, anywhere in the world, the nuclear power in on the defensive. In some countries it has been even outlawed. Some parameters show that nuclear power, on the global scale and during this century at least, is absolutely essential and reasons for revival of nuclear energy are realistic. (author)

Cancer pain management-current status

Directory of Open Access Journals (Sweden)

Deepak Thapa

2011-01-01

Full Text Available Cancer pain is still one of the most feared entities in cancer and about 75% of these patients require treatment with opioids for severe pain. The cancer pain relief is difficult to manage in patients with episodic or incidental pain, neuropathic pain, substance abuse and with impaired cognitive or communication skills. This non-systematic review article aims to discuss reasons for under treatment, tools of pain assessment, cancer pain and anxiety and possibly carve new approaches for cancer pain management in future. The current status of World Health Organization analgesic ladder has also been reviewed. A thorough literature search was carried out from 1998 to 2010 for current status in cancer pain management in MEDLINE, WHO guidelines and published literature and relevant articles have been included.

Predictive Toxicology: Current Status and Future Outlook (EBI ...

Science.gov (United States)

Slide presentation at the EBI-EMBL Industry Programme Workshop on Predictive Toxicology and the currently status of Computational Toxicology activities at the US EPA. Slide presentation at the EBI-EMBL Industry Programme Workshop on Predictive Toxicology and the currently status of Computational Toxicology activities at the US EPA.

Production of anthocyanins in metabolically engineered microorganisms: Current status and perspectives

Directory of Open Access Journals (Sweden)

Jian Zha

2017-12-01

Full Text Available Microbial production of plant-derived natural products by engineered microorganisms has achieved great success thanks to large extend to metabolic engineering and synthetic biology. Anthocyanins, the water-soluble colored pigments found in terrestrial plants that are responsible for the red, blue and purple coloration of many flowers and fruits, are extensively used in food and cosmetics industry; however, their current supply heavily relies on complex extraction from plant-based materials. A promising alternative is their sustainable production in metabolically engineered microbes. Here, we review the recent progress on anthocyanin biosynthesis in engineered bacteria, with a special focus on the systematic engineering modifications such as selection and engineering of biosynthetic enzymes, engineering of transportation, regulation of UDP-glucose supply, as well as process optimization. These promising engineering strategies will facilitate successful microbial production of anthocyanins in industry in the near future.

Laccase applications in biofuels production: current status and future prospects.

Science.gov (United States)

Kudanga, Tukayi; Le Roes-Hill, Marilize

2014-08-01

The desire to reduce dependence on the ever diminishing fossil fuel reserves coupled with the impetus towards green energy has seen increased research in biofuels as alternative sources of energy. Lignocellulose materials are one of the most promising feedstocks for advanced biofuels production. However, their utilisation is dependent on the efficient hydrolysis of polysaccharides, which in part is dependent on cost-effective and benign pretreatment of biomass to remove or modify lignin and release or expose sugars to hydrolytic enzymes. Laccase is one of the enzymes that are being investigated not only for potential use as pretreatment agents in biofuel production, mainly as a delignifying enzyme, but also as a biotechnological tool for removal of inhibitors (mainly phenolic) of subsequent enzymatic processes. The current review discusses the major advances in the application of laccase as a potential pretreatment strategy, the underlying principles as well as directions for future research in the search for better enzyme-based technologies for biofuel production. Future perspectives could include synergy between enzymes that may be required for optimal results and the adoption of the biorefinery concept in line with the move towards the global implementation of the bioeconomy strategy.

Teleradiology - current status

International Nuclear Information System (INIS)

Baltadjiev, D.; Charakchiev

2000-01-01

Tele-radiology is a term becoming increasingly popular in the medical literature. Nevertheless, terminological definitions in this particular field are still rather vague. The scope of applications extend from simple image presenting via analogue telephone lines to transmission of 3-D medical images through a satellite. It is a matter of standards highly differing in terms of data transmission rates, safety, technical demands on the systems and the like. In this article new information technologies, technical aspects, as well as some major applications of tele-radiology are discussed. The current status of tele-medicine/tele-radiology in this country is likewise briefly outlined

The socioeconomic status of the non-timber forest product subsector ...

African Journals Online (AJOL)

A wide spectrum of non-timber forest products (NTFPs) generally has a remarkable contribution to the household economy in rural areas. Most communities make a living either through their domestic or commercial use. The objective of this study was to review the current status of the NTFP sector and further compile an ...

Coenzyme Q10 production in plants: current status and future prospects.

Science.gov (United States)

Parmar, Sanjay Singh; Jaiwal, Anjali; Dhankher, Om Parkash; Jaiwal, Pawan K

2015-06-01

Coenzyme Q10 (CoQ10) or Ubiquinone10 (UQ10), an isoprenylated benzoquinone, is well-known for its role as an electron carrier in aerobic respiration. It is a sole representative of lipid soluble antioxidant that is synthesized in our body. In recent years, it has been found to be associated with a range of patho-physiological conditions and its oral administration has also reported to be of therapeutic value in a wide spectrum of chronic diseases. Additionally, as an antioxidant, it has been widely used as an ingredient in dietary supplements, neutraceuticals, and functional foods as well as in anti-aging creams. Since its limited dietary uptake and decrease in its endogenous synthesis in the body with age and under various diseases states warrants its adequate supply from an external source. To meet its growing demand for pharmaceutical, cosmetic and food industries, there is a great interest in the commercial production of CoQ10. Various synthetic and fermentation of microbial natural producers and their mutated strains have been developed for its commercial production. Although, microbial production is the major industrial source of CoQ10 but due to low yield and high production cost, other cost-effective and alternative sources need to be explored. Plants, being photosynthetic, producing high biomass and the engineering of pathways for producing CoQ10 directly in food crops will eliminate the additional step for purification and thus could be used as an ideal and cost-effective alternative to chemical synthesis and microbial production of CoQ10. A better understanding of CoQ10 biosynthetic enzymes and their regulation in model systems like E. coli and yeast has led to the use of metabolic engineering to enhance CoQ10 production not only in microbes but also in plants. The plant-based CoQ10 production has emerged as a cost-effective and environment-friendly approach capable of supplying CoQ10 in ample amounts. The current strategies, progress and constraints of

Current status of quantum electrical metrology

International Nuclear Information System (INIS)

Urano, Chiharu; Kaneko, Nobuhisa; Kiryu, Shogo

2005-01-01

Physical background, current status of proof systems and researches of the next generation standards of Josephson voltage and Quantized Hall Resistance (QHR) standard system are described. Josephson effect, the principle and theory of quantized hall effect, usual voltage standard system, standard feed of direct current resistance, and researches of voltage standard and direct current resistance standard are explained. The current-voltage of Josephson element in the usual voltage standard proof system and bias method, outline of typical Josephson voltage standard proof system and GaAs/AlGaAs heterostructure used as resistance standard are stated. Cryogenic Current Comparator (CCC) and Direct Current Comparator (DCC) proofread usual resistor. New Quantum Hall Array Resistance Standard (QHARS) is studied by BNM-LNE group in French, and the other new AC Quantized Hall Resistance (AC-QHR) by the European ACQHE Project. (S.Y.)

Current status of food irradiation in overseas (2013). From the meeting report of RCA food irradiation project

International Nuclear Information System (INIS)

Todoriki, Setsuko

2013-01-01

The report introduces the activity of RCA (Regional Cooperative Agreement for Research Development and Training Related to Nuclear Science and Technology for Asia and Pacific) food irradiation project (RAS/5/057) and information obtained at the two workshops on current status of Asia and Pacific areas together with EU, USA and Japan. Also current trends of RAS/5/057 Implementing Best Practices for food irradiation for plant sanitary and phytosanitary purposes are described. Amount of food irradiation products of RCA member countries, minimum adopted doses for quarantine harmful insects (70 to 232 Gy) and import amount of fruits of USA (79 to 5500 tons) are tabulated. Finally current status of Japan is explained. (S. Ohno)

Current status and prospects for Chernobyl Ukritiye

International Nuclear Information System (INIS)

Jampsin, B.

1996-01-01

Current status and prospects for Chernobyl Ukritiye (sarcophagus) are described, including the following issues: the accident; the sarcophagus; the radioactive inventory; the design basis criteria; the analysis of the present state; a way forward

Current Status of On-Site Wastewater Management

Science.gov (United States)

Senn, Charles L.

1978-01-01

Wastewater management is becoming an important environmental issue nationally. This article reports the history and current status of wastewater management. Regulatory programs are discussed with specific state examples. Needs assessment is also included. (MA)

[Current status and sustainable development countermeasures of Anoectochilus roxburghii].

Science.gov (United States)

Hong, Lin; Shao, Qing-Song; Zhou, Ai-Cun; Wang, Hong-Zhen; Zhang, Ai-Lian; Xu, Jian-Wei; Huang, Yu-Qiu

2016-02-01

The current status of the domestic manufacturing and sales markets of Anoectochilus roxburghii were investigated and analyzed in the study. Some problems in the A. roxburghii industry were revealed and a variety of sustainable development countermeasures were also proposed. The main problems of A. roxburghii industry are the lack of protection for wild resources, the lag in the speed of variety breeding, the insufficient research on the quality systems, the low level of industry and product innovation capability, as well as the relatively low market cognition and brand competence. Therefore, strengthening the protection for breeding resources, establishing a dynamic monitoring system, promoting the variety breeding, constructing a propagation system for improved varieties, enhancing the quality of medicinal herbs, accelerating the adjustment of product structure, upgrading the industry technology, strengthening brand competence and expanding the market, will be the effective methods to realize the sustainable development of A. roxburghii industry. Copyright© by the Chinese Pharmaceutical Association.

Current Status of Manufacturing Hazardous Waste in Shanghai

Institute of Scientific and Technical Information of China (English)

Liu Changqing; Zhang Jiangshan; Zhao Youcai

2007-01-01

It is difficult to manage the manufacturing hazardous waste(MHW)whichis generated from a huge amount of complicated sources and causes very serious pollution.Therefore more and more attention has been paid to MHW pollution.shanghai,as an industrial and economic center and an intemational metropolis in China,has a vast industrial system spanning a multitude of sectors,which generates MHW not only in a huge magnitude but also in a large variety of types from complicated sourrces,resulting in severe pollution.In 2003,the production of MHW in Shanghai is about 3.96 x 10ton,involving 33 indices.Most of MHW in Shanghai is treated and disposed of,but a significant portion is not handled properly and effectively.This paper carries out in-field investigation on the current status of MHW production and treat ment in Shanghai,and puts forward scientific proposals that Shanghai should facilitate cleaner production and minimize haz ardous waste;strictly enforce hazardous waste registration system, strengthen monitoring the certified enterprises;strengthen intent disposal center construction and realize hazardous waste reclamation;accelerate establishing tlle technical criteria and the management policy,promote the research and development on the treatment and disposal technology,and strengthen information management,thus realizing integrated management on MHW pollution.

The WIMP Paradigm: Current Status

International Nuclear Information System (INIS)

Feng, Jonathan

2011-01-01

The WIMP paradigm is the glue that joins together much of the high energy and cosmic frontiers. It postulates that most of the matter in the Universe is made of weakly-interacting massive particles, with implications for a broad range of experiments and observations. I will review the WIMP paradigm's underlying motivations, its current status in view of rapid experimental progress on several fronts, and recent theoretical variations on the WIMP paradigm theme.

Current status of GALS setup in JINR

Energy Technology Data Exchange (ETDEWEB)

Zemlyanoy, S., E-mail: zemlya@jinr.ru; Avvakumov, K., E-mail: kavvakumov@jinr.ru [Joint Institute for Nuclear Research, Flerov Laboratory of Nuclear Reactions (Russian Federation); Fedosseev, V. [CERN (Switzerland); Bark, R. [Nat. Research Foundation, iThemba LABS (South Africa); Blazczak, Z. [A. Mickiewicz University, Faculty of Physics (Poland); Janas, Z. [University of Warsaw, Faculty of Physics (Poland)

2017-11-15

This is a brief report on the current status of the new GAs cell based Laser ionization Setup (GALS) at the Flerov Laboratory for Nuclear Reactions (FLNR) of the Joint Institute for Nuclear Research (JINR) in Dubna. GALS will exploit available beams from the U-400M cyclotron in low energy multi-nucleon transfer reactions to study exotic neutron-rich nuclei located in the “north-east” region of nuclear map. Products from 4.5 to 9 MeV/nucleon heavy-ion collisions, such as {sup 136}Xe on {sup 208}Pb, are thermalized and neutralized in a high pressure gas cell and subsequently selectively laser re-ionized. In order to choose the best scheme of ion extraction the results of computer simulations of two different systems are presented. The first off- and online experiment will be performed on osmium atoms that is regarded as a most convenient element for producing isotopes with neutron number in the vicinity of the magic N = 126.

REMPAN at international level: current status

International Nuclear Information System (INIS)

Souchkevitch, Guennadi

1997-01-01

This document describes the current status of the Radiation Emergency medical Preparedness and Assistance Network - REMPAN, for the promotion of radiation emergency medical and public health preparedness and for practical assistance and advising countries, in a case of overexposure from any sources of radiation, by initiative of the World Health Organization - WHO

Current status of ion source development

International Nuclear Information System (INIS)

Ishikawa, Junzo

2001-01-01

In this report, the current status of ion source development will be discussed. In September 2001, the 9th International Conference on Ion Sources (ICIS01) was held in Oakland, U.S.A. Referring the talks presented at ICIS01, recent topics in the ion source research fields will be described. (author)

Current status and future prospect of electron beam sterilization in Japan

International Nuclear Information System (INIS)

Katsura, Ichiro

1998-01-01

It seems that electron beam sterilization is being current topic among all applications in Japan and that this tendency will continue until when major companies interested in the technology complete introducing electron beam. Since the Ministry of Health and Welfare(MOHW) officially issued revised regulation on GMP for medical devices in 1995, EtO has become the method regarded as time and money consuming one. On the contrary, electron beam has become as relatively economical and desirable method to achieve same result by its characteristics such as high productivity, rather easy validation and consequent cost reduction, although less penetration limit the kind of products to be treated. Status and prospect of electron beam sterilization in Japan will be presented in the paper along with accelerator related technologies

Status report on actinide and fission product transmutation studies

International Nuclear Information System (INIS)

1997-06-01

The management of radioactive waste is one of the key issues in today's political and public discussions on nuclear energy. One of the fields that looks into the future possibilities of nuclear technology is the neutronic transmutation of actinides and of some most important fission products. Studies on transmutation of actinides are carried out in various countries and at an international level. This status report which gives an up-to-date general overview of current and planned research on transmutation of actinides and fission products in non-OECD countries, has been prepared by a Technical Committee meeting organized by the IAEA in September 1995. 168 refs, 16 figs, 34 tabs

Bioethanol - Status report on bioethanol production from wood and other lignocellulosic feedstocks

Energy Technology Data Exchange (ETDEWEB)

Scott-Kerr, Chris; Johnson, Tony; Johnson, Barbara; Kiviaho, Jukka

2010-09-15

Lignocellulosic biomass is seen as an attractive feedstock for future supplies of renewable fuels, reducing the dependence on imported petroleum. However, there are technical and economic impediments to the development of commercial processes that utilise biomass feedstocks for the production of liquid fuels such as ethanol. Significant investment into research, pilot and demonstration plants is on-going to develop commercially viable processes utilising the biochemical and thermochemical conversion technologies for ethanol. This paper reviews the current status of commercial lignocellulosic ethanol production and identifies global production facilities.

Cobalt 60 gamma irradiation current status, trends and insights

International Nuclear Information System (INIS)

Corley, John T.

1998-01-01

This paper discusses the current status, trends and insights into the continued, safe use of cobalt 60 gamma irradiation. Also presented are some of the many initiatives undertaken at MDS Nordion. Topics covered include our investment for the future supply of raw materials and the latest news from source production. Briefly presented are the tasks associated with the safe transport of cobalt 60 around the world. Discussed is cobalt 60 usage at the customer site; more specifically maintaining source integrity, source utilization and irradiator design trends. Highlighted are industry trends for North America, Europe and the rest of the world. Finally presented are the challenges and opportunities for the industry. Stressed in the paper is the need to work together

Current status of the AUSTRON project

International Nuclear Information System (INIS)

Rauch, H.; Regler, M.; Lechner, R.E.; Weber, H.

2001-01-01

The current status of the AUSTRON spallation source project is described with reference to the need for neutrons in Europe and - due to a certain West-East imbalance of large research facilities - especially in Central Europe. A short overview about technical aspects of proton accelerator, rapid cycling synchrotron, storage ring, target and instrumentation is presented. (author)

COHERENT Experiment: current status

International Nuclear Information System (INIS)

Akimov, D; Belov, V; Bolozdynya, A; Burenkov, A; Albert, J B; Del Valle Coello, M; D’Onofrio, M; Awe, C; Barbeau, P S; Cervantes, M; Becker, B; Cabrera-Palmer, B; Collar, J I; Cooper, R J; Cooper, R L; Cuesta, C; Detwiler, J; Eberhardt, A; Dean, D; Dolgolenko, A G

2017-01-01

The COHERENT Collaboration is realizing a long term neutrino physics research program. The main goals of the program are to detect and study elastic neutrino-nucleus scattering (CEνNS). This process is predicted by Standard Model but it has never been observed experimentally because of the very low energy of the recoil nucleus. COHERENT is using different detector technologies: CsI[Na] and NaI scintillator crystals, a single-phase liquid Ar and a Ge detectors. The placement of all the detector setups is in the basement of the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory (ORNL). The current status of the COHERENT experimental program is presented. (paper)

Biosimilar drugs: Current status.

Science.gov (United States)

Kumar, Rajiv; Singh, Jagjit

2014-07-01

Biologic products are being developed over the past three decades. The expiry of patent protection for many biological medicines has led to the development of biosimilars in UK or follow on biologics in USA. This article reviews the literature on biosimilar drugs that covers the therapeutic status and regulatory guidelines. Appraisal of published articles from peer reviewed journals for English language publications, search from PubMed, and guidelines from European Medicines Agency, US Food Drug Administration (FDA) and India were used to identify data for review. Literature suggest that biosimilars are similar biological products, i.e., comparable but not identical to the reference product, are not generic version of innovator product and do not ensure therapeutic equivalence. Biosimilars present more challenges than conventional generics and marketing approval is also more complicated. To improve access, US Congress passed the Biologics Price Competition and Innovation act 2009 and US FDA allowed "abbreviated pathway" for their approval. U.S law has defined new standards and terms and EMA scientific guidelines have also set detailed approval standards. India being one of the most preferred manufacturing destinations of biosimilars, there is a need for stringent safety and regulatory guidelines. The New India Guidelines "Draft Guidelines on Similar Biologics were announced in June 2012, by Department of Biotechnology at Boston bio and available online.

Health Status of Current National Guard Members

National Research Council Canada - National Science Library

Proctor, Susan P

2005-01-01

.... The objectives are to: 1) describe the current health status of this ARNG cohort, 2) examine to what extent the job strain of ARNG service affects the relationship between Civilian job strain and health and job performance outcomes and, 3...

Current status of fusion-relevant covariance data

International Nuclear Information System (INIS)

Muir, D.W.

1994-01-01

The following review of the current status of formatted data covariance files and their multigroup processing is a contribution to the IAEA Advisory Group Meeting on ''Improved Evaluations and Integral Data Testing for FENDL,'' to be held at the Max-Planck-Institut fuer Plasmaphysik, Garching, Germany, 12--16 September 1994. The draft agenda of this meeting lists as Item 6 the ''assessment of present status and role of uncertainty files, their processing and sensitivity studies related to FENDL.'' We conclude that this is an important and timely topic and recommend needed actions in this field

Current Status and Future Prospects of Marine Natural Products (MNPs) as Antimicrobials.

Science.gov (United States)

Choudhary, Alka; Naughton, Lynn M; Montánchez, Itxaso; Dobson, Alan D W; Rai, Dilip K

2017-08-28

The marine environment is a rich source of chemically diverse, biologically active natural products, and serves as an invaluable resource in the ongoing search for novel antimicrobial compounds. Recent advances in extraction and isolation techniques, and in state-of-the-art technologies involved in organic synthesis and chemical structure elucidation, have accelerated the numbers of antimicrobial molecules originating from the ocean moving into clinical trials. The chemical diversity associated with these marine-derived molecules is immense, varying from simple linear peptides and fatty acids to complex alkaloids, terpenes and polyketides, etc. Such an array of structurally distinct molecules performs functionally diverse biological activities against many pathogenic bacteria and fungi, making marine-derived natural products valuable commodities, particularly in the current age of antimicrobial resistance. In this review, we have highlighted several marine-derived natural products (and their synthetic derivatives), which have gained recognition as effective antimicrobial agents over the past five years (2012-2017). These natural products have been categorized based on their chemical structures and the structure-activity mediated relationships of some of these bioactive molecules have been discussed. Finally, we have provided an insight into how genome mining efforts are likely to expedite the discovery of novel antimicrobial compounds.

Australian shellfish ecosystems: Past distribution, current status and future direction.

Directory of Open Access Journals (Sweden)

Chris L Gillies

Full Text Available We review the status of marine shellfish ecosystems formed primarily by bivalves in Australia, including: identifying ecosystem-forming species, assessing their historical and current extent, causes for decline and past and present management. Fourteen species of bivalves were identified as developing complex, three-dimensional reef or bed ecosystems in intertidal and subtidal areas across tropical, subtropical and temperate Australia. A dramatic decline in the extent and condition of Australia's two most common shellfish ecosystems, developed by Saccostrea glomerata and Ostrea angasi oysters, occurred during the mid-1800s to early 1900s in concurrence with extensive harvesting for food and lime production, ecosystem modification, disease outbreaks and a decline in water quality. Out of 118 historical locations containing O. angasi-developed ecosystems, only one location still contains the ecosystem whilst only six locations are known to still contain S. glomerata-developed ecosystems out of 60 historical locations. Ecosystems developed by the introduced oyster Crasostrea gigas are likely to be increasing in extent, whilst data on the remaining 11 ecosystem-forming species are limited, preventing a detailed assessment of their current ecosystem-forming status. Our analysis identifies that current knowledge on extent, physical characteristics, biodiversity and ecosystem services of Australian shellfish ecosystems is extremely limited. Despite the limited information on shellfish ecosystems, a number of restoration projects have recently been initiated across Australia and we propose a number of existing government policies and conservation mechanisms, if enacted, would readily serve to support the future conservation and recovery of Australia's shellfish ecosystems.

Australian shellfish ecosystems: Past distribution, current status and future direction

Science.gov (United States)

Gillies, Chris L.; McLeod, Ian M.; Alleway, Heidi K.; Cook, Peter; Crawford, Christine; Creighton, Colin; Diggles, Ben; Ford, John; Hamer, Paul; Heller-Wagner, Gideon; Lebrault, Emma; Le Port, Agnès; Russell, Kylie; Sheaves, Marcus; Warnock, Bryn

2018-01-01

We review the status of marine shellfish ecosystems formed primarily by bivalves in Australia, including: identifying ecosystem-forming species, assessing their historical and current extent, causes for decline and past and present management. Fourteen species of bivalves were identified as developing complex, three-dimensional reef or bed ecosystems in intertidal and subtidal areas across tropical, subtropical and temperate Australia. A dramatic decline in the extent and condition of Australia’s two most common shellfish ecosystems, developed by Saccostrea glomerata and Ostrea angasi oysters, occurred during the mid-1800s to early 1900s in concurrence with extensive harvesting for food and lime production, ecosystem modification, disease outbreaks and a decline in water quality. Out of 118 historical locations containing O. angasi-developed ecosystems, only one location still contains the ecosystem whilst only six locations are known to still contain S. glomerata-developed ecosystems out of 60 historical locations. Ecosystems developed by the introduced oyster Crasostrea gigas are likely to be increasing in extent, whilst data on the remaining 11 ecosystem-forming species are limited, preventing a detailed assessment of their current ecosystem-forming status. Our analysis identifies that current knowledge on extent, physical characteristics, biodiversity and ecosystem services of Australian shellfish ecosystems is extremely limited. Despite the limited information on shellfish ecosystems, a number of restoration projects have recently been initiated across Australia and we propose a number of existing government policies and conservation mechanisms, if enacted, would readily serve to support the future conservation and recovery of Australia’s shellfish ecosystems. PMID:29444143

Current status of methods for shielding analysis

International Nuclear Information System (INIS)

Engle, W.W.

1980-01-01

Current methods used in shielding analysis and recent improvements in those methods are discussed. The status of methods development is discussed based on needs cited at the 1977 International Conference on Reactor Shielding. Additional areas where methods development is needed are discussed

Cyclotron facilities in Brazil: Current status and licensing aspects

International Nuclear Information System (INIS)

Facure, A.; Carvalho, S.M.; Di Prinzio, R.; Silveira, C.S.; Gasparian, P.B.R.; Franca, W.F.

2017-01-01

Positron Emission Tomography (PET) is a highly sensitive and accurate nuclear medicine imaging technology but the major problem of this technique is the use of radioisotopes with short half-life, less than two hours. The production and selling of short half-life radioisotopes used to be monopoly of the Brazilian Government. In 2006, a Constitutional Amendment revoked the state monopoly due to the need for the use of short half-life radioisotopes in nuclear medicine centers very far from the government production facilities. The aim of this study is to describe the current status of short half-life radioisotopes production in Brazil and discuss some licensing process. In Brazil, as has been occurring worldwide, the number of nuclear medicine centers is increasing. Currently there are 123 services performing PET scans in Brazil. There are 14 cyclotrons operating in Brazil. The type of licensing process conducted in Brazil does not take into account the population density of each state, with a free competition model being adopted. Because of this there is a lot of equipment concentrated in the Southeast and no cyclotrons operating in the Northern part of the country. One of the biggest obstacles during the licensing process is the designation of qualified personnel as operation workers and radiation safety officers. The number of cyclotron accelerators and PET/CT equipment increased in recent years. However, a number of external factors such as the distance from the nuclear medicine centers, and qualified personnel have proved crucial for the economic viability of this type of facility. (author)

Cyclotron facilities in Brazil: Current status and licensing aspects

Energy Technology Data Exchange (ETDEWEB)

Facure, A.; Carvalho, S.M.; Di Prinzio, R.; Silveira, C.S.; Gasparian, P.B.R.; Franca, W.F., E-mail: facure@cnen.gov.br [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil)

2017-09-01

Positron Emission Tomography (PET) is a highly sensitive and accurate nuclear medicine imaging technology but the major problem of this technique is the use of radioisotopes with short half-life, less than two hours. The production and selling of short half-life radioisotopes used to be monopoly of the Brazilian Government. In 2006, a Constitutional Amendment revoked the state monopoly due to the need for the use of short half-life radioisotopes in nuclear medicine centers very far from the government production facilities. The aim of this study is to describe the current status of short half-life radioisotopes production in Brazil and discuss some licensing process. In Brazil, as has been occurring worldwide, the number of nuclear medicine centers is increasing. Currently there are 123 services performing PET scans in Brazil. There are 14 cyclotrons operating in Brazil. The type of licensing process conducted in Brazil does not take into account the population density of each state, with a free competition model being adopted. Because of this there is a lot of equipment concentrated in the Southeast and no cyclotrons operating in the Northern part of the country. One of the biggest obstacles during the licensing process is the designation of qualified personnel as operation workers and radiation safety officers. The number of cyclotron accelerators and PET/CT equipment increased in recent years. However, a number of external factors such as the distance from the nuclear medicine centers, and qualified personnel have proved crucial for the economic viability of this type of facility. (author)

Current Status of Single-incision Laparoscopic Surgery

DEFF Research Database (Denmark)

Ahmed, Irfan; Ciancio, Fabio; Ferrara, Vincenzo

2012-01-01

Recent advances in minimally invasive surgery have centered on reducing the number of incisions required, which has led to the development of the single-incision laparoscopic technique. A panel of European single-incision laparoscopy experts met to discuss the current status of, and the future...

Current status of Uganda Kob (Kobus Kob Thomasi Neumann) in ...

African Journals Online (AJOL)

Current status of Uganda Kob (Kobus Kob Thomasi Neumann) in Toro Game Reserve, Uganda. ... As part of a biological assessment of Toro Game Reserve, the status of Uganda kob Kobus kob Thomasi ... AJOL African Journals Online.

Radiation processing. Current status and future possibilities

International Nuclear Information System (INIS)

Woods, R.J.

2000-01-01

Radiation processing developed following the Second World War and employees gamma- or electron-irradiation to process polymers, cure alkene-based inks and coatings, sterilize medical supplies, irradiate food, and manage wastes. The current status of these applications is described with the probable direction of future developments. (author)

Current status of high-T{sub c} wire

Energy Technology Data Exchange (ETDEWEB)

Vase, Per [Nordic Superconductor Technologies A/S, Priorparken 685, DK 2605 Broendby (Denmark); Fluekiger, Rene [Departement de Physique de la Matiere Condensee, Universite de Geneve (Switzerland); Leghissa, Martino [Siemens AG, Corporate Technology, Erlangen (Germany); Glowacki, Bartek [Department of Material Science and Metallurgy, University of Cambridge, Cambridge CB2 3QZ (United Kingdom)

2000-07-01

This paper is the result of the work of a SCENET (The European Network for Superconductivity) material working group's efforts on giving values for present and future expected performance of high-temperature superconducting (HTS) wires and tapes. The purpose of the work is to give input to the design of HTS applications like power cables, motors, current leads, magnets, transformers and generators. The current status performance values are supposed to be used in the design of today's prototypes and the future values for the design of fully commercial HTS applications of the future. We focus on what is expected to be the relevant parameters for HTS application design. The most successful technique by far for making HTS tapes has been on the (Bi, Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} (Bi-2223) material by the powder-in-tube (PIT) technique and this paper therefore focuses on giving the current status and expected future performance for Bi-2223 tapes. (author)

Benthic microalgal production in the Arctic: Applied methods and status of the current database

DEFF Research Database (Denmark)

Glud, Ronnie Nøhr; Woelfel, Jana; Karsten, Ulf

2009-01-01

The current database on benthic microalgal production in Arctic waters comprises 10 peer-reviewed and three unpublished studies. Here, we compile and discuss these datasets, along with the applied measurement approaches used. The latter is essential for robust comparative analysis and to clarify ...

Current Status of HPV Vaccines

Science.gov (United States)

Ma, Barbara; Roden, Richard; Wu, T.C.

2010-01-01

Cervical cancer is the second largest cause of cancer deaths in women worldwide, with ~500,000 diagnoses and 274,000 deaths annually. It remains a significant source of morbidity and mortality despite effective screening tools and treatments for its precursor high-grade cervical intraepithelial neoplasia (CIN). Increased understanding of cervical pathogenesis has led to the identification of human papillomavirus (HPV) as the etiological agent for cervical cancer and the development of preventive and therapeutic vaccines targeting HPV antigens for the control of cervical cancer. Herein, we discuss the current status of HPV vaccines. PMID:20677402

The Current Status of Biodiesel Production Technology: A Review

Directory of Open Access Journals (Sweden)

Rizal Alamsyah

2007-12-01

Full Text Available Biodiesel is addressed to the name of fuel which consist of mono-alkyl ester that made from renewable and biodegradable resources, such as oils from plants (vegetable oils, waste or used cooking oil, and animal fats. Such oils or fats are chemically reacted with alcohols or methanol In producing chernical compounds called fatty acid methyl ester (FAME and these reactions are called transesterification and esterification. Glycerol, used in the pharmaceutical and cosmetics industry is produced from biodiesel production as a by-product. Researches on biodiesel as an alternative petroleum diesel have been done for more than 20 years. Transesterification reaction can be acid-catalyzed, alkali-catatyzed, or enzyme-catalyzed. Commercially biodiesel is processed by transesterification with alkali catalyst. This process, however, requires refining of products and recovery of catalysts, Such biodiesel production accelerates researches on biodiesel to obtain simpler methods, better quality. and minimum production cost. Besides the catalytic production for biodiesel, there is a method for biodiesel production namely non-catalytic production. Non-catalytic transesterification method was developed since catalytic tranestertfification still has two main problems assoclated With long reaction time and complicated purification. The first problem occurres because of the two phase nature of vegetable oil/methanol mixture, and the last problem is due to purification of catalyst and glycerol. The application of catalytic tranestertfication method leads to condition of high biodiesel production cost and high energy consumption. This paper provides information of biodiesel production progress namely catalytic tranestertfification (acid, alkali, and enzymatic tranesterfification, and non-catalytic tranesterification (at sub-critical­-supercritical temperature under pressurized conditions. It was found that every method of biodiesel production still has advantages and

Current status and challenges for automotive battery production technologies

Science.gov (United States)

Kwade, Arno; Haselrieder, Wolfgang; Leithoff, Ruben; Modlinger, Armin; Dietrich, Franz; Droeder, Klaus

2018-04-01

Production technology for automotive lithium-ion battery (LIB) cells and packs has improved considerably in the past five years. However, the transfer of developments in materials, cell design and processes from lab scale to production scale remains a challenge due to the large number of consecutive process steps and the significant impact of material properties, electrode compositions and cell designs on processes. This requires an in-depth understanding of the individual production processes and their interactions, and pilot-scale investigations into process parameter selection and prototype cell production. Furthermore, emerging process concepts must be developed at lab and pilot scale that reduce production costs and improve cell performance. Here, we present an introductory summary of the state-of-the-art production technologies for automotive LIBs. We then discuss the key relationships between process, quality and performance, as well as explore the impact of materials and processes on scale and cost. Finally, future developments and innovations that aim to overcome the main challenges are presented.

Current status of neutron scattering in Thailand

International Nuclear Information System (INIS)

Kornduangkaeo, Areeratt; Pongkasem, Somchai; Putchar, Suriya; Ampornrat, Pantip; Kajornrith, Varavuth; Chamchang, Jipawat

2006-01-01

The current neutron powder diffractometer at the Thai Research Reactor-1/Modification 1 (TRR-1/M1) has been modified from the obsolete neutron diffractometer which had been used during 1968-1975. The upgraded diffractometer has medium resolution and is appropriate for studying samples with small unit cell dimensions and training university students in the field of neutron scattering. This paper describes the current activities of neutron scattering research in Thailand, the current status of a new research reactor project at Ongkarak for enlarging the perspectives of its utilization in the future as well as the organizational reformation of the Office of Atomic Energy for Peace (OAEP). (author)

Advanced Gas Tungsten Arc Weld Surfacing Current Status and Application

Directory of Open Access Journals (Sweden)

Stephan Egerland

2015-09-01

Full Text Available Abstract Gas Shielded Tungsten Arc Welding (GTAW – a process well-known providing highest quality weld results joined though by lower performance. Gas Metal Arc Welding (GMAW is frequently chosen to increase productivity along with broadly accepted quality. Those industry segments, especially required to produce high quality corrosion resistant weld surfacing e.g. applying nickel base filler materials, are regularly in consistent demand to comply with "zero defect" criteria. In this conjunction weld performance limitations are overcome employing advanced 'hot-wire' GTAW systems. This paper, from a Welding Automation perspective, describes the technology of such devices and deals with the current status is this field – namely the application of dual-cathode hot-wire electrode GTAW cladding; considerably broadening achievable limits.

Dark Matter Detection: Current Status

International Nuclear Information System (INIS)

Akerib, Daniel S.

2011-01-01

Overwhelming observational evidence indicates that most of the matter in the Universe consists of non-baryonic dark matter. One possibility is that the dark matter is Weakly-Interacting Massive Particles (WIMPs) that were produced in the early Universe. These relics could comprise the Milky Way's dark halo and provide evidence for new particle physics, such as Supersymmetry. This talk focuses on the status of current efforts to detect dark matter by testing the hypothesis that WIMPs exist in the galactic halo. WIMP searches have begun to explore the region of parameter space where SUSY particles could provide dark matter candidates.

MDSplus integration at TCABR tokamak: Current status

International Nuclear Information System (INIS)

Sá, W.P. de; Ronchi, G.

2016-01-01

Highlights: • The implementation of MDSplus in TCABR tokamak, current status. • Interfaces between the system already installed and the MDSplus. • Web MDSplus interface. - Abstract: Experimental data for the TCABR tokamak is currently stored in MDSplus (Model Driven System Plus) database. The access to the data recorded during the experiments is performed using tools and libraries available by MDSplus system. The MDSplus system is widely used in different physics experiments, especially in plasmas physics and nuclear fusion. This standardized environment enables easy interaction among scientists of different experiments in different countries without the need to understand the particular characteristics of control, data acquisition and analysis, and remote access (CODAS) customized in each laboratory. In the first phase of implementation, intermediate interfaces had been developed between the legacy proprietary system and the MDSplus. In a second phase, the new diagnostic systems had been directly included in the created MDSplus system in the laboratory. After three years of use, the system installed on TCABR proved extremely efficient and significantly increased productivity in data analysis by involved scientists, regardless of whether they are locally at the TCABR, or accessing the system remotely from their home laboratories. The third phase, and subject of this article, are the development and implementation of the following systems: (i) web tools for the visualization of data, integrated with the experiment logbook, (ii) integration of MDSplus with applications (LabVIEW + MDSplus) and newer data acquisition hardware.

MDSplus integration at TCABR tokamak: Current status

Energy Technology Data Exchange (ETDEWEB)

Sá, W.P. de, E-mail: pires@if.usp.br; Ronchi, G., E-mail: gronchi@if.usp.br

2016-11-15

Highlights: • The implementation of MDSplus in TCABR tokamak, current status. • Interfaces between the system already installed and the MDSplus. • Web MDSplus interface. - Abstract: Experimental data for the TCABR tokamak is currently stored in MDSplus (Model Driven System Plus) database. The access to the data recorded during the experiments is performed using tools and libraries available by MDSplus system. The MDSplus system is widely used in different physics experiments, especially in plasmas physics and nuclear fusion. This standardized environment enables easy interaction among scientists of different experiments in different countries without the need to understand the particular characteristics of control, data acquisition and analysis, and remote access (CODAS) customized in each laboratory. In the first phase of implementation, intermediate interfaces had been developed between the legacy proprietary system and the MDSplus. In a second phase, the new diagnostic systems had been directly included in the created MDSplus system in the laboratory. After three years of use, the system installed on TCABR proved extremely efficient and significantly increased productivity in data analysis by involved scientists, regardless of whether they are locally at the TCABR, or accessing the system remotely from their home laboratories. The third phase, and subject of this article, are the development and implementation of the following systems: (i) web tools for the visualization of data, integrated with the experiment logbook, (ii) integration of MDSplus with applications (LabVIEW + MDSplus) and newer data acquisition hardware.

ATM in Europe: analysis of current status

DEFF Research Database (Denmark)

1999-01-01

This deliverable provides an overview of the current status of the European market for ATM services. The offer of ATM services by principal operators in Belgium, Denmark, Finland, France, Germany, Greece, Italy, Norway, Portugal, Spain, Sweden and United Kingdom is described. In addition, a number...... of international providers of ATM in Europe are presented....

Current status of accreditation for drug testing in hair.

Science.gov (United States)

Cooper, Gail; Moeller, Manfred; Kronstrand, Robert

2008-03-21

At the annual meeting of the Society of Hair Testing in Vadstena, Sweden in 2006, a committee was appointed to address the issue of guidelines for hair testing and to assess the current status of accreditation amongst laboratories offering drug testing in hair. A short questionnaire was circulated amongst the membership and interested parties. Fifty-two responses were received from hair testing laboratories providing details on the amount and type of hair tests they offered and the status of accreditation within their facilities. Although the vast majority of laboratories follow current guidelines (83%), only nine laboratories were accredited to ISO/IEC 17025 for hair testing. A significant number of laboratories reporting that they were in the process of developing quality systems with a view to accrediting their methods within 2-3 years. This study provides an insight into the status of accreditation in hair testing laboratories and supports the need for guidelines to encourage best practice.

Production and supply of radioisotopes with high-energy particle accelerators current status and future directions

International Nuclear Information System (INIS)

Srivastava, S.C.; Mausner, L.F.

1994-01-01

Although the production of radioisotopes in reactors or in low to medium energy cyclotrons appears to be relatively well established, especially for those isotopes that are routinely used and have a commercial market, certain isotopes can either be made only in high-energy particle accelerators or their production is more cost effective when made this way. These facilities are extremely expensive to build and operate, and isotope production is, in general, either not cost-effective or is in conflict with their primary mandate or missions which involve physics research. Isotope production using high-energy accelerators in the US, therefore, has been only an intermittent and parasitic activity. However, since a number of isotopes produced at higher energies are emerging as being potentially useful for medical and other applications, there is a renewed concern about their availability in a continuous and reliable fashion. In the US, in particular, the various aspects of the prediction and availability of radioisotopes from high-energy accelerators are presently undergoing a detailed scrutiny and review by various scientific and professional organizations as well as the Government. A number of new factors has complicated the supply/demand equation. These include considerations of cost versus needs, reliability factors, mission orientation, research and educational components, and commercial viability. This paper will focus on the present status and projected needs of radioisotope production with high-energy accelerators in the US, and will compare and examine the existing infrastructure in other countries for this purpose

Product Operations Status Summary Metrics

Science.gov (United States)

Takagi, Atsuya; Toole, Nicholas

2010-01-01

The Product Operations Status Summary Metrics (POSSUM) computer program provides a readable view into the state of the Phoenix Operations Product Generation Subsystem (OPGS) data pipeline. POSSUM provides a user interface that can search the data store, collect product metadata, and display the results in an easily-readable layout. It was designed with flexibility in mind for support in future missions. Flexibility over various data store hierarchies is provided through the disk-searching facilities of Marsviewer. This is a proven program that has been in operational use since the first day of the Phoenix mission.

Current status of production and supply of molybdenum-99 and 99Mo/99mTc generators in Indonesia

International Nuclear Information System (INIS)

Mutalib, A.

2003-01-01

Production of high-specific activity molybdenum-99 and 99 Mo/ 99m Tc Generators in Indonesia commenced when a new production facility supported by the presence of a 30 MW multipurpose reactor (RSG-GAS) was established in Serpong in 1990. This report describes the current production and supply of molybdenum-99m devoted mainly to fulfill the domestic demands in supplying 99 Mo/ 99m Tc Generators. Recent development on the use of LEU (Low Enriched Uranium) targets for replacing current HEU (High Enriched Uranium) targets in the production of 99 Mo will be reviewed briefly. (author)

Lung cancer: Current status and prospects for the future

International Nuclear Information System (INIS)

Mountain, C.F.; Carr, D.T.

1986-01-01

This book contains 32 papers. Some of the titles are: Activation of cellular ras genes in human neoplasms; The valve of definitive radiation therapy of unresectable squamous cell carcinoma, large cell carcinoma, and adenocarcinoma of the lung; Current concepts of chemotherapy and radiotherapy for small cell lung cancer, and Current status of immunotherapy for lung cancer

Chemical Reaction Engineering: Current Status and Future Directions.

Science.gov (United States)

Dudukovic, M. P.

1987-01-01

Describes Chemical Reaction Engineering (CRE) as the discipline that quantifies the interplay of transport phenomena and kinetics in relating reactor performance to operating conditions and input variables. Addresses the current status of CRE in both academic and industrial settings and outlines future trends. (TW)

The nonparametric bootstrap for the current status model

NARCIS (Netherlands)

Groeneboom, P.; Hendrickx, K.

2017-01-01

It has been proved that direct bootstrapping of the nonparametric maximum likelihood estimator (MLE) of the distribution function in the current status model leads to inconsistent confidence intervals. We show that bootstrapping of functionals of the MLE can however be used to produce valid

Job monitoring on the WLCG scope: Current status and new strategy

International Nuclear Information System (INIS)

Andreeva, Julia; Casey, James; Gaidioz, Benjamin; Karavakis, Edward; Kokoszkiewicz, Lukasz; Lanciotti, Elisa; Maier, Gerhild; Rodrigues, Daniele Filipe Rocha Da Cuhna; Rocha, Ricardo; Saiz, Pablo; Sidorova, Irina; Boehm, Max; Belov, Sergey; Tikhonenko, Elena; Dvorak, Frantisek; Krenek, Ales; Mulac, Milas; Sitera, Jiri; Kodolova, Olga; Vaibhav, Kumar

2010-01-01

Job processing and data transfer are the main computing activities on the WLCG infrastructure. Reliable monitoring of the job processing on the WLCG scope is a complicated task due to the complexity of the infrastructure itself and the diversity of the currently used job submission methods. The paper will describe current status and the new strategy for the job monitoring on the WLCG scope, covering primary information sources, job status changes publishing, transport mechanism and visualization.

Current status and directions for fast reactor reprocessing

International Nuclear Information System (INIS)

Burch, W.D.

1983-01-01

The development of fast breeder reactors (FBRs) for commercial electric power production has been under way in several countries for more than 20 years. In the United States (US), as elsewhere, early work was focused on small reactors to prove the feasibility of concepts and later was followed by larger reactors to test engineering features and to develop fuel technology. Because of the perceived crisis in electrical generation expected late in this century, major efforts (including fuel cycle activities) were developed in the early 1970s to ensure the capability of developing and using this new form of nuclear power. However, because of the effects of the oil price rise and subsequent emphasis on conservation, and a slowdown of industrial growth, there has been a decline in such activities, particularly in the US, which was at one time (1970s) the world leader in reactor development. This paper provides a brief history of breeder reprocessing and describes the current status, with emphasis on US programs and glimpses into the future

Marine current energy devices: Current status and possible future applications in Ireland

International Nuclear Information System (INIS)

Rourke, Fergal O.; Boyle, Fergal; Reynolds, Anthony

2010-01-01

There is a growing demand for the use of renewable energy technologies to generate electricity due to concerns over climate change. The oceans provide a huge potential resource of energy. Energy extraction using marine current energy devices (MCEDs) offers a sustainable alternative to conventional sources and a predictable alternative to other renewable energy technologies. A MCED utilises the kinetic energy of the tides as opposed to the potential energy which is utilised by a tidal barrage. Over the past decade MCEDs have become an increasingly popular method of energy extraction. However, marine current energy technology is still not economically viable on a large scale due to its current stage of development. Ireland has an excellent marine current energy resource as it is an island nation and experiences excellent marine current flows. This paper reviews marine current energy devices, including a detailed up-to-date description of the current status of development. Issues such as network integration, economics, and environmental implications are addressed as well as the application and costs of MCEDs in Ireland. (author)

Structural Learning Theory: Current Status and New Perspectives.

Science.gov (United States)

Scandura, Joseph M.

2001-01-01

Presents the current status and new perspectives on the Structured Learning Theory (SLT), with special consideration given to how SLT has been influenced by recent research in software engineering. Topics include theoretical constructs; content domains; structural analysis; cognition; assessing behavior potential; and teaching and learning issues,…

Neutrino astronomy current status, future prospects

CERN Document Server

Karle, Albrecht

2017-01-01

This review volume is motivated by the recent discovery of high-energy astrophysical neutrinos by IceCube. The aim of the book is to bring together chapters on the status of current and future neutrino observatories with chapters on the implications and possible interpretations of the present observations and their upper limits. Each chapter is a mini-review of one aspect of the subject by leading experts. Taken together, the chapters constitute an up-to-date review of high-energy astrophysical neutrinos and their potential sources.

Production and supply of radioisotopes with high-energy particle accelerators current status and future directions

International Nuclear Information System (INIS)

Srivastava, S.C.; Mausner, L.F.

1994-01-01

Although the production of radioisotopes in reactors or in low to medium energy cyclotrons appears to be relatively well established, certain isotopes can either be made only in high-energy particle accelerators or their production is more cost effective when made this way. These facilities are extremely expensive to build and operate, and isotope production is, in general, either not cost-effective or is in conflict with their primary mandate or missions which involve physics research. Isotope production using high-energy accelerators in the U.S., therefore, has been only an intermittent and parasitic activity. However, since a number of isotopes produced at higher energies are emerging as being potentially useful for medical and other applications, there is a renewed concern about their availability in a continuous and reliable fashion. In the U.S., in particular, the various aspects of the production and availability of radioisotopes from high-energy accelerators are presently undergoing a detailed scrutiny and review by various scientific and professional organizations as well as the Government. A number of new factors has complicated the supply/demand equation. These include considerations of cost versus needs, reliability factors, mission orientation, research and educational components, and commercial viability. This paper will focus on the present status and projected needs of radioisotope production with high-energy accelerators in the U.S., and will compare and examine the existing infrastructure in other countries for this purpose. The nature of the U.S. decisions to address many of the above-mentioned issues and an eventual plan of attack to resolve them are bound to have a world-wide impact in the radioisotope user communities. These will be discussed with a view to evaluating the best possible solutions in order to eliminate the shortage in the future supply of radioisotopes produced in high energy accelerators. (author)

Biohydrogen Production by the Thermophilic Bacterium Caldicellulosiruptor saccharolyticus: Current Status and Perspectives

Directory of Open Access Journals (Sweden)

Servé W. M. Kengen

2013-01-01

Full Text Available Caldicellulosiruptor saccharolyticus is one of the most thermophilic cellulolytic organisms known to date. This Gram-positive anaerobic bacterium ferments a broad spectrum of mono-, di- and polysaccharides to mainly acetate, CO2 and hydrogen. With hydrogen yields approaching the theoretical limit for dark fermentation of 4 mol hydrogen per mol hexose, this organism has proven itself to be an excellent candidate for biological hydrogen production. This review provides an overview of the research on C. saccharolyticus with respect to the hydrolytic capability, sugar metabolism, hydrogen formation, mechanisms involved in hydrogen inhibition, and the regulation of the redox and carbon metabolism. Analysis of currently available fermentation data reveal decreased hydrogen yields under non-ideal cultivation conditions, which are mainly associated with the accumulation of hydrogen in the liquid phase. Thermodynamic considerations concerning the reactions involved in hydrogen formation are discussed with respect to the dissolved hydrogen concentration. Novel cultivation data demonstrate the sensitivity of C. saccharolyticus to increased hydrogen levels regarding substrate load and nitrogen limitation. In addition, special attention is given to the rhamnose metabolism, which represents an unusual type of redox balancing. Finally, several approaches are suggested to improve biohydrogen production by C. saccharolyticus.

Current status and installation of dental PACS

International Nuclear Information System (INIS)

Park, Chang Seo; Kim, Kee Deog; Park, Hyok; Jeong, Ho Gul

2004-01-01

Picture Archiving and Communication System (PACS) is difficult to implement in the best of situations, but evidence is growing that the benefits are significant. The aims of this study are to analyze the current status of full PACS and establish successful installation standard of dental PACS. Materials and Methods were based on the investigation of current working status and installation standard of PACS, and observation of variable issues to installation of dental PACS. By September 30, 2004, full PACS implementations in their facilities were 88.1% in specialized general hospitals (37 installations out of total 42 hospitals), 59.8% in general hospitals (144 installations out of total 241 hospitals), 12.3% in medical hospitals (116 installations out of total 941 hospitals) and 3.6% in dental hospitals (4 installations out of total 110 hospitals). Only 4 university dental hospitals currently have installed and are operating full PACS. Major obstacle to wide spread of dental PACS is initial high investments. Clinical environments of dental PACS differed from medical situation. Because of characteristic dental practice, the initial investments for dental PACS are generally much greater than those of medical PACS. Also new economic crisis makes users scruple. The best way to overcome these limitations is to establish an economic installation standard for dental PACS. Also the clear technical communication between the customer and the supplier before both sides are committed to the obstacles are critical to its success.

Current Status of the Elevated Temperature Structure Design Codes for VHTR

International Nuclear Information System (INIS)

Kim, Jong-Bum; Kim, Seok-Hoon; Park, Keun-Bae; Lee, Won-Jae

2006-01-01

An elevated temperature structure design and analysis is one of the key issues in the VHTR (Very High Temperature Reactor) project to achieve an economic production of hydrogen which will be an essential energy source for the near future. Since the operating temperature of a VHTR is above 850 .deg. C, the existing code and standards are insufficient for a high temperature structure design. Thus the issues concerning a material selection and behaviors are being studied for the main structural components of a VHTR in leading countries such as US, France, UK, and Japan. In this study, the current status of the ASME code, French RCC-MR, UK R5, and Japanese code were investigated and the necessary R and D items were discussed

Current Status and Prediction on Development of PE Market

Institute of Scientific and Technical Information of China (English)

Yu Jiao

2003-01-01

This article comprehensively analyzes the status of market demand/supply and import/export volumes of PE in the world and in China, and predicts the future development trends in the fields of PE production and consumption.

Current Icing Product

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Current Icing Product (CIP) is an automatically-generated index suitable for depicting areas of potentially hazardous airframe icing. The CIP algorithm combines...

Soil environmental quality in greenhouse vegetable production systems in eastern China: Current status and management strategies.

Science.gov (United States)

Hu, Wenyou; Zhang, Yanxia; Huang, Biao; Teng, Ying

2017-03-01

Greenhouse vegetable production (GVP) has become an important source of public vegetable consumption and farmers' income in China. However, various pollutants can be accumulated in GVP soils due to the high cropping index, large agricultural input, and closed environment. Ecological toxicity caused by excessive pollutants' accumulation can then lead to serious health risks. This paper was aimed to systematically review the current status of soil environmental quality, analyze their impact factors, and consequently to propose integrated management strategies for GVP systems. Results indicated a decrease in soil pH, soil salinization, and nutrients imbalance in GVP soils. Fungicides, remaining nutrients, antibiotics, heavy metals, and phthalate esters were main pollutants accumulating in GVP soils comparing to surrounding open field soils. Degradation of soil ecological function, accumulation of major pollutants in vegetables, deterioration of neighboring water bodies, and potential human health risks has occurred due to the changes of soil properties and accumulation of pollutants such as heavy metals and fungicides in soils. Four dominant factors were identified leading to the above-mentioned issues including heavy application of agricultural inputs, outmoded planting styles with poor environmental protection awareness, old-fashion regulations, unreasonable standards, and ineffective supervisory management. To guarantee a sustainable GVP development, several strategies were suggested to protect and improve soil environmental quality. Implementation of various strategies not only requires the concerted efforts among different stakeholders, but also the whole lifecycle assessment throughout the GVP processes as well as effective enforcement of policies, laws, and regulations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Special Education History, Current Status and Future: India

Science.gov (United States)

Antony, Pavan John

2013-01-01

Education of all children in public schools, including those with disabilities, continues to be an unresolved issue in many countries around the globe. While education of all children is mandated by law and considered a basic human right in many countries, the current status of implementation varies. India, for example, is an ancient country that…

Current status of agricultural extension services for market oriented ...

African Journals Online (AJOL)

Current status of agricultural extension services for market oriented agricultural development in Ethiopia: Results from a household baseline ... Log in or Register to get access to full text downloads. ... http://dx.doi.org/10.4314/afrrev.v10i3.1.

The ENIQ pilot study: current status

Energy Technology Data Exchange (ETDEWEB)

Lemaitre, P; Eriksen, B; Crutzen, S [European Commission, DG Joint Research Centre, Petten (Netherlands); Hansch, M [Preussische Elektrizitaets-AG (Preussenelektra), Hannover (Germany); Whittle, J [AEA Technology, Warrington (United Kingdom)

1998-11-01

A pilot study is currently being carried out by ENIQ (European Network for Inspection Qualification) in order to explore the issues involved in inspection qualification applied along the general principles of the European methodology. The components selected for the pilot study are austenitic pipe to pipe and pipe to elbows welds typical of those in BWR recirculation loops. A range of defect parameters has been defined. A suitable inspection procedure designed to find the designated defects will be applied to geometrically representative test pieces. The procedure/equipment will be qualified through open trials and technical justification. The personnel qualification will be done in a blind way. Once all features of the inspection system will have been qualified an in-service inspection will be simulated in order to test the feasibility of the qualification approach followed. In this paper the current status of this pilot study is discussed. (orig.)

Current status of laparoscopic central pancreatectomy

Directory of Open Access Journals (Sweden)

CAO Yang

2017-04-01

Full Text Available Central pancreatectomy is an ideal surgical procedure for the treatment of benign or low-grade malignant tumors in the pancreatic neck or the proximal body of the pancreas, and it can preserve more normal pancreatic tissue in order to reduce the incidence of endocrine and exocrine insufficiency after surgery. Although some clinical studies have demonstrated the feasibility and safety of this procedure, laparoscopic central pancreatectomy was technically challenging with a few number of cases. This article reviews the current status of laparoscopic central pancreatectomy and introduces our clinical experience of laparoscopic central pancreatectomy and pancreaticojejunostomy.

Production and supply of radioisotopes with reactors in north america and europe current status and future prospects

International Nuclear Information System (INIS)

Trevena, I.

1994-01-01

Reactors have played a key pole in the production of radioactive isotopes for medical applications for the past 50 years. This paper reviews current and future capabilities for the production and supply of radioactive isotopes used in nuclear medicine. It focuses primarily on the supply of fission product molybdenum-99, which is used to produce technetium-99m, the radioisotope most widely employed in nuclear medicine procedures. The significant infrastructure required for the production and supply of molybdenum-99 is detailed, and the capabilities of the major commercial suppliers in North America and Europe are discussed. Plans for increasing production capabilities in the future are also reviewed. (author)

TMI-2 [Three Mile Island] fission product inventory program: FY-85 status report

International Nuclear Information System (INIS)

Langer, S.; Croney, S.T.; Akers, D.W.; Russell, M.L.

1986-11-01

This report presents the status of the TMI-2 fission product inventory program through May 1985. The fission product inventory program is an assessment of the location of fission products distributed in the plant as a result of the TMI-2 accident. Included in this report are principal results of samples from the reactor building where most of the mobile fission products (i.e., radiocesium and iodine) are expected to be found. The data are now complete enough for most reactor components; therefore, it is possible to direct the balance of the examination and sampling program to areas and components where it is likely to be most productive. Those areas are the reactor core and the reactor building basement, with emphasis on the currently unsampled portions of the core

Current status of pediatric minimal access surgery at Sultan Qaboos ...

African Journals Online (AJOL)

Keywords: current status, laparoscopy, minimal access surgery, thoracoscopy. Departments of ... Materials and methods ... procedures, the open technique was used for the creation ... operated for bilateral inguinal herniotomy had recurrence.

Regression analysis of informative current status data with the additive hazards model.

Science.gov (United States)

Zhao, Shishun; Hu, Tao; Ma, Ling; Wang, Peijie; Sun, Jianguo

2015-04-01

This paper discusses regression analysis of current status failure time data arising from the additive hazards model in the presence of informative censoring. Many methods have been developed for regression analysis of current status data under various regression models if the censoring is noninformative, and also there exists a large literature on parametric analysis of informative current status data in the context of tumorgenicity experiments. In this paper, a semiparametric maximum likelihood estimation procedure is presented and in the method, the copula model is employed to describe the relationship between the failure time of interest and the censoring time. Furthermore, I-splines are used to approximate the nonparametric functions involved and the asymptotic consistency and normality of the proposed estimators are established. A simulation study is conducted and indicates that the proposed approach works well for practical situations. An illustrative example is also provided.

Helicopter Rotor Noise Prediction: Background, Current Status, and Future Direction

Science.gov (United States)

Brentner, Kenneth S.

1997-01-01

Helicopter noise prediction is increasingly important. The purpose of this viewgraph presentation is to: 1) Put into perspective the recent progress; 2) Outline current prediction capabilities; 3) Forecast direction of future prediction research; 4) Identify rotorcraft noise prediction needs. The presentation includes an historical perspective, a description of governing equations, and the current status of source noise prediction.

Microbial Production of Short Chain Fatty Acids from Lignocellulosic Biomass: Current Processes and Market

Directory of Open Access Journals (Sweden)

Ivan Baumann

2016-01-01

Full Text Available Biological production of organic acids from conversion of biomass derivatives has received increased attention among scientists and engineers and in business because of the attractive properties such as renewability, sustainability, degradability, and versatility. The aim of the present review is to summarize recent research and development of short chain fatty acids production by anaerobic fermentation of nonfood biomass and to evaluate the status and outlook for a sustainable industrial production of such biochemicals. Volatile fatty acids (VFAs such as acetic acid, propionic acid, and butyric acid have many industrial applications and are currently of global economic interest. The focus is mainly on the utilization of pretreated lignocellulosic plant biomass as substrate (the carbohydrate route and development of the bacteria and processes that lead to a high and economically feasible production of VFA. The current and developing market for VFA is analyzed focusing on production, prices, and forecasts along with a presentation of the biotechnology companies operating in the market for sustainable biochemicals. Finally, perspectives on taking sustainable product of biochemicals from promise to market introduction are reviewed.

Current knowledge of US metal and nonmetal miner health: Current and potential data sources for analysis of miner health status

Science.gov (United States)

Yeoman, K. M.; Halldin, C. N.; Wood, J.; Storey, E.; Johns, D.; Laney, A. S.

2016-01-01

ABSTRACT Little is known about the current health status of US metal and nonmetal (MNM) miners, in part because no health surveillance systems exist for this population. The National Institute for Occupational Safety and Health (NIOSH) is developing a program to characterize burden of disease among MNM miners. This report discusses current knowledge and potential data sources of MNM miner health. Recent national surveys were analyzed, and literature specific to MNM miner health status was reviewed. No robust estimates of disease prevalence were identified, and national surveys did not provide information specific to MNM miners. Because substantial gaps exist in the understanding of MNM miners' current health status, NIOSH plans to develop a health surveillance program for this population to guide intervention efforts to reduce occupational and personal risks for chronic illness. PMID:25658684

Current status of radiation treatment of water and wastewater

International Nuclear Information System (INIS)

Pikaev, A.K.

1997-01-01

This is a brief review of the current status of radiation treatment of surface water, groundwater, wastewaters, and sewage sludges. Sources of ionizing radiation, and combination radiation methods for purification are described in some detail. Special attention is paid to pilot and industrial facilities. (author)

[Current status and prospects of gene doping detection].

Science.gov (United States)

Wang, Wenjun; Zhang, Sichun; Xu, Jingjuan; Xia, Xinghua; Tian, Yaping; Zhang, Xinrong; Chen, Hong-Yuan

2008-07-01

The fast development of biotechnology promotes the development of doping. From recombinant protein to gene doping, there is a great challenge to their detection. The improvement of gene therapy and potential to enhance athletic performance open the door for gene doping. After a brief introduction of the concept of gene doping, the current status and prospects of gene doping detection are reviewed.

Distal protection in cardiovascular medicine: current status.

Science.gov (United States)

Ali, Onn Akbar; Bhindi, Ravinay; McMahon, Aisling C; Brieger, David; Kritharides, Leonard; Lowe, Harry C

2006-08-01

Iatrogenic and spontaneous downstream microembolization of atheromatous material is increasingly recognized as a source of cardiovascular morbidity and mortality. Devising ways of reducing this distal embolization using a variety of mechanical means--distal protection--is currently under intense and diverse investigation. This review therefore summarizes the present status of distal protection. It examines the problem of distal embolization, describes the available distal protection devices, reviews those areas of cardiovascular medicine where distal protection devices are being investigated, and discusses potential future developments.

[The health food product Noni--does marketing harmonize with the current status of research?].

Science.gov (United States)

Johansen, Rolf

2008-03-13

Norwegian cancer patients frequently use Noni. The objective of this study was to find out whether the way noni is marketed in Norway and the health claims made about the product harmonize with current scientific knowledge of its benefits/adverse effects. An overview of medical research on noni was obtained from three databases. Web sites for private persons and for companies that sell noni in Norway were examined. Books, pamphlets etc. from a company specializing in selling information material about noni, were also examined. 48 scientific articles were included in the study, but none of these were clinical studies of humans. Several pharmacological effects of noni have been shown in vitro and in animal models (e.g., increased survival for animals with cancer). Information material describes noni as a health-promoting product that patients with most diseases will benefit from. Noni is to a great extent sold by multi-level marketing, but is also commonly sold by health food stores. There is no scientific basis for claiming that patients will benefit from using noni for any diseases. The way this product is sold has several worrying aspects.

The current status of wind energy in Turkey and in the world

International Nuclear Information System (INIS)

Ilkilic, Cumali; Aydin, Hueseyin; Behcet, Rasim

2011-01-01

The rapid increase in world energy demand, the depletion of conventional energy sources and the pollution caused by conventional fuels have increased the importance of developing new and renewable energy sources. Additionally, technological developments have resulted in increased energy demand for the entire world, including Turkey, especially for electrical energy. At present, wind energy is receiving considerable attention. This report focuses on the current status of wind energy in Turkey and in the world. An overview of wind energy in Turkey is presented, and its current status, application, support mechanisms and associated legislation in Turkey are described. Wind energy and its status in the world are also addressed. It can be concluded from this analysis that wind energy utilization in Turkey and throughout world has sharply increased. Turkey has an abundance of wind energy sources. - Research highlights: →The importance of wind energy utilization. →Wind energy status, potential, applications, legislations and supports in Turkey. →An overview of wind energy the world.

Current status of neutron scattering in Thailand

International Nuclear Information System (INIS)

Ampornrat, Pantip

2000-01-01

The neutron scattering experiments in Thailand have been done continuously since the start up of the reactor. In 1977, Thai research reactor was modified into TRIGA MARK III core. After that, the neutron spectrometer was installed again under a development program. Installation of upgrading spectrometer was delayed because of some problems involving the neutron intensity and instruments. However, these problems were solved and the setup is almost completed. The paper reports the current status of neutron spectrometer, the problems and plans for the experiments. (author)

Current Status of Mycotoxin Contamination of Food Commodities in Zimbabwe

Directory of Open Access Journals (Sweden)

Nancy Nleya

2018-05-01

Full Text Available Agricultural products, especially cereal grains, serve as staple foods in sub-Saharan Africa. However, climatic conditions in this region can lead to contamination of these commodities by moulds, with subsequent production of mycotoxins posing health risks to both humans and animals. There is limited documentation on the occurrence of mycotoxins in sub-Saharan African countries, leading to the exposure of their populations to a wide variety of mycotoxins through consumption of contaminated foods. This review aims at highlighting the current status of mycotoxin contamination of food products in Zimbabwe and recommended strategies of reducing this problem. Zimbabwe is one of the African countries with very little information with regards to mycotoxin contamination of its food commodities, both on the market and at household levels. Even though evidence of multitoxin occurrence in some food commodities such as maize and other staple foods exist, available published research focuses only on Aspergillus and Fusarium mycotoxins, namely aflatoxins, deoxynivalenol (DON, trichothecenes, fumonisins, and zearalenone (ZEA. Occurrence of mycotoxins in the food chain has been mainly associated with poor agricultural practices. Analysis of mycotoxins has been done mainly using chromatographic and immunological methods. Zimbabwe has adopted European standards, but the legislation is quite flexible, with testing for mycotoxin contamination in food commodities being done voluntarily or upon request. Therefore, the country needs to tighten its legislation as well as adopt stricter standards that will improve the food safety and security of the masses.

Current Status of Mycotoxin Contamination of Food Commodities in Zimbabwe.

Science.gov (United States)

Nleya, Nancy; Adetunji, Modupeade Christianah; Mwanza, Mulunda

2018-05-03

Agricultural products, especially cereal grains, serve as staple foods in sub-Saharan Africa. However, climatic conditions in this region can lead to contamination of these commodities by moulds, with subsequent production of mycotoxins posing health risks to both humans and animals. There is limited documentation on the occurrence of mycotoxins in sub-Saharan African countries, leading to the exposure of their populations to a wide variety of mycotoxins through consumption of contaminated foods. This review aims at highlighting the current status of mycotoxin contamination of food products in Zimbabwe and recommended strategies of reducing this problem. Zimbabwe is one of the African countries with very little information with regards to mycotoxin contamination of its food commodities, both on the market and at household levels. Even though evidence of multitoxin occurrence in some food commodities such as maize and other staple foods exist, available published research focuses only on Aspergillus and Fusarium mycotoxins, namely aflatoxins, deoxynivalenol (DON), trichothecenes, fumonisins, and zearalenone (ZEA). Occurrence of mycotoxins in the food chain has been mainly associated with poor agricultural practices. Analysis of mycotoxins has been done mainly using chromatographic and immunological methods. Zimbabwe has adopted European standards, but the legislation is quite flexible, with testing for mycotoxin contamination in food commodities being done voluntarily or upon request. Therefore, the country needs to tighten its legislation as well as adopt stricter standards that will improve the food safety and security of the masses.

The current status and perspectives of biofuel production via catalytic cracking of edible and non-edible oils

International Nuclear Information System (INIS)

Ong, Yee Kang; Bhatia, Subhash

2010-01-01

Biofuel development has gained the attention of researchers in recent years owing to the rate of depletion of fossil fuels. Several processes are currently employed in the conventional production of different biofuels: the production of biodiesel is catalytically performed either through the transesterification of triglycerides using alcohol or the deoxygenative ecofining of triglycerides in a non-alcohol environment; bio-oil is produced by the pyrolysis of biomass; bio-ethanol is produced by the fermentation of sugars obtained from starch or cellulosic based biomass, while bio-gasoline is produced from the catalytic cracking of triglycerides. Owing to the enormous dependency of transport vehicles running on gasoline engines, the development of bio-gasoline may well reduced the dependence of the fuel market on fossil fuels. The present article summarizes recent progresses and future prospects of biofuel production via catalytic cracking technology. This technology can be implemented in current petroleum refineries with minor modifications. However, reactor design and catalyst choice are important issues and have to be addressed before successful implementation of this technology in commercial ventures.

Thermal management issues in a PEMFC stack - A brief review of current status

International Nuclear Information System (INIS)

Kandlikar, Satish G.; Lu Zijie

2009-01-01

Understanding the thermal effects is critical in optimizing the performance and durability of proton exchange membrane fuel cells (PEMFCs). A PEMFC produces a similar amount of waste heat to its electric power output and tolerates only a small deviation in temperature from its design point. The balance between the heat production and its removal determines the operating temperature of a PEMFC. These stringent thermal requirements present a significant heat transfer challenge. In this work, the fundamental heat transfer mechanisms at PEMFC component level (including polymer electrolyte, catalyst layers, gas diffusion media and bipolar plates) are briefly reviewed. The current status of PEMFC cooling technology is also reviewed and research needs are identified

Current status of RCA projects and strategies for future implementation

International Nuclear Information System (INIS)

Kim, Kyoung Pyo; Lee, Jeong Kong

1998-12-01

This report is intended to provide basic overall information about ways to promote technical cooperation within the framework of RCA to accelerate and coordinate cooperative activities in nuclear science and technology in Asia and the Pacific region through a thorough review on the current status and through suggesting future implementation strategies. The contents of this report include an overall introduction of RCA, guidelines and operating rules for RCA programmes, current status and future plans for RCA projects as well as the RCA vision for the next 25 years. By reviewing the current status and future implementation strategies for RCA projects, it will help to set up a national nuclear policy aimed at seeking maximum benefits from participation in RCA projects and to implement programmes for nuclear cooperation with Asian-Pacific countries. It is expected that as a lead country for the energy sector, which is one of five thematic areas for the year 1999 - 2000 cycle programmes, Korea will continue to make significant contributions towards the implementation of RCA programmes in the future. With this report, we plan to keep up with future developments as well as implement an effective cooperation with the countries in the region so that the opinion of Korea, one of the nuclear advanced countries in the region, can be fully reflected in the establishment of future plans for RCA programmes. (author). 3 refs., 5 tabs., 1 fig

Impact of the severity of vasomotor symptoms on health status, resource use, and productivity.

Science.gov (United States)

Whiteley, Jennifer; Wagner, Jan-Samuel; Bushmakin, Andrew; Kopenhafer, Lewis; Dibonaventura, Marco; Racketa, Jill

2013-05-01

The current study characterizes health-related quality of life, work productivity, and resource use among postmenopausal women by severity of vasomotor symptoms (VMS). Participants were selected from the 2010 US National Health and Wellness Survey. Women aged 40 to 75 years who did not report a history of menstrual bleeding or spotting for 1 year were eligible for analysis (N = 3,267). Cohorts of women with no VMS (n = 1,740), mild VMS (n = 931), moderate VMS (n = 462), and severe VMS (n = 134) were compared after controlling for demographic and health characteristics. Outcome measures were assessed using linear models and included health status, work productivity within the past 7 days, and healthcare resource use within the past 6 months. The mean age of women experiencing severe VMS was 57.92 years. After demographic and health characteristics had been controlled for, women experiencing severe and moderate VMS reported significantly lower mean health status scores compared with women with no symptoms (P women with severe, moderate, or mild symptoms than among women with no symptoms (P women experiencing VMS, women with severe and moderate symptoms had adjusted presenteeism of 24.28% and 14.3%, versus 4.33% in women with mild symptoms (P women with mild symptoms (P women, a greater severity of VMS is significantly associated with lower levels of health status and work productivity, and greater healthcare resource use.

Current Status of Yongbyon Nuclear Complex

Energy Technology Data Exchange (ETDEWEB)

Hwang, Yong Soo [Korea Institute of Nuclear Non-proliferation and Control, Daejeon (Korea, Republic of)

2016-05-15

The DPRK has developed Yongbyon Nuclear Complex in Figure 1 since 1960's. Currently it is composed of the reactor facility, fuel fabrication facility including the enrichment center, and the radiochemistry center. Even though many facilities are not modern and economic in the western standards, Yongbyon Nuclear Complex is fully equipped with the entire life cycle of the nuclear installation. The key facilities have been added step by step. For example, the DPRK's nuclear reactor fleet started with the 2 MW IRT-2000 reactor in the middle of 80's. It started with a small scale radioactive isotope separation center nearby. But nowadays the DPRK is constructing a much more larger isotope separation center in the vicinity of its enrichment center along with a potential new UF6 conversion center. The general description over Yongbyon Nuclear Complex is given in this paper. More detailed context of the current status of the center will be discussed in the main symposium purely based on the open source information study.

Current status and future direction of the MONK software package

International Nuclear Information System (INIS)

Smith, Nigel; Armishaw, Malcolm; Cooper, Andrew

2003-01-01

The current status of the MONK criticality software package is summarized in terms of recent and current developments and envisaged directions for the future. The areas of the discussion are physics modeling, geometry modeling, source modeling, nuclear data, validation, supporting tools and customer services. In future development plan, MONK continues to be focused on meeting the short and long-term needs of the code user community. (J.P.N.)

Cost Estimating in DoD: Current Status, Trends, and What the Future Holds

National Research Council Canada - National Science Library

Nussbaum, Daniel A

2005-01-01

(1) Current Status: Baseline analysis of current cost estimating community, including which organizations are responsible for developing and reviewing cost estimates, how many personnel there are, what...

Hardwood lumber supply chain: current status and market opportunities

Science.gov (United States)

Urs Buehlmann; Matthew Bumgardner; Al Schuler; Mark Barford

2007-01-01

The membership of the Appalachian Hardwood Manufacturers Association was surveyed in 2005 to determine the current status of large Appalachian sawmills. The primary focus was to assess the impacts of globalization on primary manufacturing, but attention was also paid to general issues affecting the hardwood lumber supply chain-from concerns over forest health and log...

Smart wearable systems: current status and future challenges.

Science.gov (United States)

Chan, Marie; Estève, Daniel; Fourniols, Jean-Yves; Escriba, Christophe; Campo, Eric

2012-11-01

Extensive efforts have been made in both academia and industry in the research and development of smart wearable systems (SWS) for health monitoring (HM). Primarily influenced by skyrocketing healthcare costs and supported by recent technological advances in micro- and nanotechnologies, miniaturisation of sensors, and smart fabrics, the continuous advances in SWS will progressively change the landscape of healthcare by allowing individual management and continuous monitoring of a patient's health status. Consisting of various components and devices, ranging from sensors and actuators to multimedia devices, these systems support complex healthcare applications and enable low-cost wearable, non-invasive alternatives for continuous 24-h monitoring of health, activity, mobility, and mental status, both indoors and outdoors. Our objective has been to examine the current research in wearable to serve as references for researchers and provide perspectives for future research. Herein, we review the current research and development of and the challenges facing SWS for HM, focusing on multi-parameter physiological sensor systems and activity and mobility measurement system designs that reliably measure mobility or vital signs and integrate real-time decision support processing for disease prevention, symptom detection, and diagnosis. For this literature review, we have chosen specific selection criteria to include papers in which wearable systems or devices are covered. We describe the state of the art in SWS and provide a survey of recent implementations of wearable health-care systems. We describe current issues, challenges, and prospects of SWS. We conclude by identifying the future challenges facing SWS for HM. Copyright © 2012 Elsevier B.V. All rights reserved.

Current and potential trade in horticultural products irradiated for phytosanitary purposes

International Nuclear Information System (INIS)

Bustos-Griffin, Emilia; Hallman, Guy J.; Griffin, Robert L.

2012-01-01

The current status of trade in horticultural products irradiated for phytosanitary purposes is examined, including trends, strengths and weaknesses. A strategy is proposed to take advantage of the best future opportunities for increasing trade in irradiated horticultural products by identifying best possibilities for expanding both the number and volume of commodities for irradiation and then applying appropriate business criteria in a general analysis of the commodities, commercial scenarios, and geographic regions where the greatest potential exists for expansion. The results show that fresh fruits such as mango, papaya, citrus, grapes, and vegetables such as tomatoes, onions, asparagus, garlic, and peppers from Asia and the Americas show the greatest potential. Substantial opportunities for additional growth exist, especially as regulatory conditions become more favorable. - Highlights: ► This research examined the trade in horticultural products irradiated for Phytosanitary purposes. ► Paper describes strategies for enhancing trade in irradiated horticultural products. ► Results identify commodities and regions with the greatest potential. ► Additional growth potential exists, especially as regulatory conditions become more favorable.

Counseling in Malaysia: History, Current Status, and Future Trends

Science.gov (United States)

See, Ching Mey; Ng, Kok-Mun

2010-01-01

This article presents an overview of the history of counseling in Malaysia, provides an update of its current status, and discusses some anticipated future trends for the profession in light of recent developments in the country. Counseling in Malaysia began with school guidance in the 1960s and has now achieved recognition as a profession in…

Current status of Pohang Neutron Facility

Energy Technology Data Exchange (ETDEWEB)

Kim, G.N.; Lee, Y.S.; Cho, M.H. [Pohang Accelerator Laboratory, POSTECH, Pohang (KR)] [and others

2000-03-01

We present the current status of Pohang Neutron Facility, which is the pulsed neutron facility, based on the 70-MeV electron linear accelerator completed on Dec.1997. We have prepared the 15-m time-of-flight path, a Ta-target system, and the Data Acquisition System. Meanwhile we have measured the total cross-sections of Dy and Hf samples at the Research Reactor Institute, Kyoto University and the neutron capture cross-sections of {sup 164}Dy isotope at Research Laboratory for Nuclear Reactors, Tokyo Institute of Technology both in Japan. We also were participated the experiment at the 122-m flight path of the IBR-30 pulsed neutron source of Joint Institute of Nuclear Research in Dubna, Russia. (author)

Instantaneous Project Controls: Current Status, State of the Art, Benefits, and Strategies

Science.gov (United States)

Abbaszadegan, Amin

2016-01-01

Despite advancements in construction and construction-related technology, capital project performance deviations, typically overruns, remain endemic within the capital projects industry. Currently, management is generally unaware of the current status of their projects, and thus monitoring and control of projects are not achieved effectively. In…

Current utilization of research reactor on radioisotopes production in China

International Nuclear Information System (INIS)

Liu Yishu

2000-01-01

The main technical parameters of the four research reactors and their current utilization status in radioisotope manufacture and labeling compounds preparation are described. The radioisotopes, such as Co-60 sealed source, Ir-192 sealed source, γ-knife source, I-131, I-125, Sm-153, P-32 series products, In-113m generator, Tc-99m gel generator, Re-188 gel generator, C-14, Ba-131, Sr-89, 90 Y, etc., and their labeling compounds prepared from the reactor produced radionuclides, such as I-131-MIBG, I-131-Hippure, I-131-capsul, Sm-153-EDTMP, Re-186-HEDP, Re-186-HA, C-14-urea, and radioimmunoassay kits etc. are presented as well. Future development plan of radioisotopes and labeling compounds in China is also given. Simultaneously, the possibility and methods of bilateral or multilateral co-operation in utilization of research reactor, personnel and technology exchange of radioisotope production and labeling compounds is also discussed. (author)

Current utilization of research reactor on radioisotopes production in China

Energy Technology Data Exchange (ETDEWEB)

Liu Yishu [Nuclear Power Institute of China, Chengdu (China)

2000-10-01

The main technical parameters of the four research reactors and their current utilization status in radioisotope manufacture and labeling compounds preparation are described. The radioisotopes, such as Co-60 sealed source, Ir-192 sealed source, {gamma}-knife source, I-131, I-125, Sm-153, P-32 series products, In-113m generator, Tc-99m gel generator, Re-188 gel generator, C-14, Ba-131, Sr-89, {sup 90}Y, etc., and their labeling compounds prepared from the reactor produced radionuclides, such as I-131-MIBG, I-131-Hippure, I-131-capsul, Sm-153-EDTMP, Re-186-HEDP, Re-186-HA, C-14-urea, and radioimmunoassay kits etc. are presented as well. Future development plan of radioisotopes and labeling compounds in China is also given. Simultaneously, the possibility and methods of bilateral or multilateral co-operation in utilization of research reactor, personnel and technology exchange of radioisotope production and labeling compounds is also discussed. (author)

CT colonography: current status in Europe and future perspectives

International Nuclear Information System (INIS)

Lefere, P.; Gryspeerdt, S.; Yoshida, H.

2007-01-01

In this article, we review the current status of CT colonography (CTC) in Europe and future perspectives of CTC including fecal tagging and CAD. There are several large multi-centre studies that have been initiated. Fecal tagging has gradually become a prerequisite to perform state-of-the-art CTC. However, CAD for fecal-tagging CTC remains a subject for future research. (orig.)

Current status of application of Moessbauer effect in geology and mineralogy

International Nuclear Information System (INIS)

Xu Binfu

1995-01-01

The paper briefly introduces the current status of the application of Moessbauer effect in geology and mineralogy. It shows that geology and mineralogy are very active fields in the application of Moessbauer effect

Ethiopia's emerging domestic biogas sector : Current status, bottlenecks and drivers

NARCIS (Netherlands)

Kamp, L.M.; Bermúdez Forn, Esteban

2016-01-01

Ethiopia experiences an energy and environmental crisis due to the sustained reliance on woody biomass to satisfy its energy needs. This situation could be improved by using biogas. This paper analyses the current status of the domestic biogas sector in Ethiopia and identifies barriers and

Edible vaccines: Current status and future

Directory of Open Access Journals (Sweden)

Lal P

2007-01-01

Full Text Available Edible vaccines hold great promise as a cost-effective, easy-to-administer, easy-to-store, fail-safe and socioculturally readily acceptable vaccine delivery system, especially for the poor developing countries. It involves introduction of selected desired genes into plants and then inducing these altered plants to manufacture the encoded proteins. Introduced as a concept about a decade ago, it has become a reality today. A variety of delivery systems have been developed. Initially thought to be useful only for preventing infectious diseases, it has also found application in prevention of autoimmune diseases, birth control, cancer therapy, etc. Edible vaccines are currently being developed for a number of human and animal diseases. There is growing acceptance of transgenic crops in both industrial and developing countries. Resistance to genetically modified foods may affect the future of edible vaccines. They have passed the major hurdles in the path of an emerging vaccine technology. Various technical obstacles, regulatory and non-scientific challenges, though all seem surmountable, need to be overcome. This review attempts to discuss the current status and future of this new preventive modality.

Current status of Paragonimus and paragonimiasis in Ecuador

Directory of Open Access Journals (Sweden)

Manuel Calvopiña

2014-11-01

Full Text Available A review of national and international publications on paragonimiasis in Ecuador, epidemiological records from the Ministry of Public Health and unpublished research data was conducted to summarise the current status of the parasite/disease. The purpose of the review is to educate physicians, policy-makers and health providers on the status of the disease and to stimulate scientific investigators to conduct further research. Paragonimiasis was first diagnosed in Ecuador 94 years ago and it is endemic to both tropical and subtropical regions in 19 of 24 provinces in the Pacific Coast and Amazon regions. Paragonimus mexicanus is the only known species in the country, with the mollusc Aroapyrgus colombiensis and the crabs Moreirocarcinus emarginatus, Hypolobocera chilensis and Hypolobocera aequatorialis being the primary and secondary intermediate hosts, respectively. Recent studies found P. mexicanus metacercariae in Trichodactylus faxoni crabs of the northern Amazon. Chronic pulmonary paragonimiasis is commonly misdiagnosed and treated as tuberculosis and although studies have demonstrated the efficacy of praziquantel and triclabendazole for the treatment of human infections, neither drug is available in Ecuador. Official data recorded from 1978-2007 indicate an annual incidence of 85.5 cases throughout the 19 provinces, with an estimated 17.2% of the population at risk of infection. There are no current data on the incidence/prevalence of infection, nor is there a national control programme.

Parametric overdispersed frailty models for current status data.

Science.gov (United States)

Abrams, Steven; Aerts, Marc; Molenberghs, Geert; Hens, Niel

2017-12-01

Frailty models have a prominent place in survival analysis to model univariate and multivariate time-to-event data, often complicated by the presence of different types of censoring. In recent years, frailty modeling gained popularity in infectious disease epidemiology to quantify unobserved heterogeneity using Type I interval-censored serological data or current status data. In a multivariate setting, frailty models prove useful to assess the association between infection times related to multiple distinct infections acquired by the same individual. In addition to dependence among individual infection times, overdispersion can arise when the observed variability in the data exceeds the one implied by the model. In this article, we discuss parametric overdispersed frailty models for time-to-event data under Type I interval-censoring, building upon the work by Molenberghs et al. (2010) and Hens et al. (2009). The proposed methodology is illustrated using bivariate serological data on hepatitis A and B from Flanders, Belgium anno 1993-1994. Furthermore, the relationship between individual heterogeneity and overdispersion at a stratum-specific level is studied through simulations. Although it is important to account for overdispersion, one should be cautious when modeling both individual heterogeneity and overdispersion based on current status data as model selection is hampered by the loss of information due to censoring. © 2017, The International Biometric Society.

The current implementation status of the integration of sports and physical activity into Dutch rehabilitation care

NARCIS (Netherlands)

Hoekstra, Femke; Hettinga, Florentina J; Alingh, Rolinde A; Duijf, Marjo; Dekker, Rienk; van der Woude, Lucas H V; van der Schans, Cees P

PURPOSE: To describe the current status of the nationwide implementation process of a sports and physical activity stimulation programme to gain insight into how sports and physical activity were integrated into Dutch rehabilitation care. METHODS: The current implementation status of a sports and

Oak Ridge Isotope Products and Services - Current and Expected Supply and Demand

International Nuclear Information System (INIS)

Aaron, W.S.; Alexander, C.W.; Cline, R.L.; Collins, E.D.; Klein, J.A.; Knauer, J.B. Jr.; Mirzadeh, S.

1999-01-01

Oak Ridge National Laboratory (ORNL) has been a major center of isotope production research, development, and distribution for over 50 years. Currently, the major isotope production activities include (1) the production of transuranium element radioisotopes, including 252 Cf; (2) the production of medical and industrial radioisotopes; (3) maintenance and expansion of the capabilities for production of enriched stable isotopes; and, (4) preparation of a wide range of custom-order chemical and physical forms of isotope products, particularly in accelerator physics research. The recent supply of and demand for isotope products and services in these areas, research and development (R ampersand D), and the capabilities for future supply are described in more detail below. The keys to continuing the supply of these important products and services are the maintenance, improvement, and potential expansion of specialized facilities, including (1) the High Flux Isotope Reactor (HFIR), (2) the Radiochemical Engineering Development Center (REDC) and Radiochemical Development Laboratory (RDL) hot cell facilities, (3) the electromagnetic calutron mass separators and the plasma separation process equipment for isotope enrichment, and (4) the Isotope Research Materials Laboratory (IRML) equipment for preparation of specialized chemical and physical forms of isotope products. The status and plans for these ORNL isotope production facilities are also described below

Indirect dark matter searches: current status and perspectives

CERN Multimedia

CERN. Geneva

2016-01-01

Many theoretical ideas for the particle nature of dark matter exist. The  most popular models often predict that dark matter particles self-annihilate or decay, giving rise to potentially detectable signatures in astronomical observations.  I will summarize the current status of searches for such signatures and critically reassess recent claims for dark matter signals.  I will further provide an outlook on anticipated developments in the next 10 years, and discuss new methods to facilitate strategy development.

ZnO growth technologies: current status and perspectives

International Nuclear Information System (INIS)

Lupan, Oleg

2011-01-01

Development of new technologies for ZnO nano materials and thin films is of critical importance for further fundamental investigations and practical applications. We discuss on the main technical control of the synthesis of zinc oxide and its properties, which are of significance in understanding the growth mechanism and further developing ZnO-based devices. Next, we present a brief summary of recent research activities, current status and progress in developing improved control of technological processes for zinc oxide as advanced material.

Status of readout integrated circuits for radiation detector

International Nuclear Information System (INIS)

Moon, B. S.; Hong, S. B.; Cheng, J. E. and others

2001-09-01

In this report, we describe the current status of readout integrated circuits developed for radiation detectors, along with new technologies being applied to this field. The current status of ASCIC chip development related to the readout electronics is also included in this report. Major sources of this report are from product catalogs and web sites of the related industries. In the field of semiconductor process technology in Korea, the current status of the multi-project wafer(MPW) of IDEC, the multi-project chip(MPC) of ISRC and other domestic semiconductor process industries is described. In the case of other countries, the status of the MPW of MOSIS in USA and the MPW of EUROPRACTICE in Europe is studied. This report also describes the technologies and products of readout integrated circuits of industries worldwide

Investigation on Current Status of World Nuclear Education and Training

International Nuclear Information System (INIS)

Shin, J. Y.; Min, M. J.; Noh, B. C.

2010-04-01

All over the world, the interest of nuclear energy is increasing and the expectations of it are getting more as one of the most practical alternative energy resources. However, since 1990s, as a lot of nuclear specialists are being retired, now the problem of manpower shortage is taken into consideration for all of us and will be continued until 2011. In this point of view, the good quality of the professional nuclear training and education systems and the nuclear education centers are requested in order to breed and supply the next generation nuclear scientists and engineers. Thus, the objective of this study is to explore the current status of world nuclear education for both of nuclear power countries and potential nuclear power utilization countries in the near future. This report introduces the importance of nuclear energy, the current status of world nuclear power plants operation and the contribution of nuclear energy. Besides, it also includes the nuclear energy development plan of potential nuclear developing countries in the near future. In addition, this study also explores the nuclear training and education systems of the nuclear development countries and the current status of nuclear education in various fields such as government, industries, nuclear power plants ect. Especially, as considering the status of nuclear education classified such as Asia, the Americas, East and West Europe, the Middle East and Africa, it shows the different characteristics of nuclear education systems in each regions aimed to identify the good practices on the nuclear education systems. Finally, through observation of international cooperation and networks of the various nuclear organizations, this will be contributed to the development of nuclear education for member states and be suggested the various of the direction of development for nuclear education in Korea. The report presents in the basis of the recent status data of the world nuclear education systems collected

Current status of quantitative rotational spectroscopy for atmospheric research

Science.gov (United States)

Drouin, Brian J.; Wlodarczak, Georges; Colmont, Jean-Marcel; Rohart, Francois

2004-01-01

Remote sensing of rotational transitions in the Earth's atmosphere has become an important method for the retrieval of geophysical temperatures, pressures and chemical composition profiles that requires accurate spectral information. This paper highlights the current status of rotational data that are useful for atmospheric measurements, with a discussion of the types the rotational lineshape measurements that are not generally available in either online repository.

Review of the current status of radiation risk estimates

International Nuclear Information System (INIS)

Charles, M.W.; Little, M.P.

1988-10-01

This report reviews the current status of radiation risk estimation for low linear energy transfer radiation. Recent statements by various national and international organisations regarding risk estimates are critically discussed. The recently published revised population risk estimates from the study of Japanese bomb survivors are also reviewed and used with some unpublished data from Japan to calculate risk figures for a general work force. (author)

Current Diagnosis, Treatment and Etiology of Status Epilepticus

Directory of Open Access Journals (Sweden)

Çetin Kürşad Akpınar

2014-03-01

Full Text Available Status Epilepticus (SE is a medical emergency that causes significant morbidity and mortality and requires prompt diagnosis and treatment. Although SE can be divided into two subgroups as convulsive and nonconvulsive, treatment principles are generally similar. Treatment should be prompt and underlying cause should be corrected. Although intravenous lorazepam is the first-line treatment due to a lower risk of relapse, diazepam becomes the first choice since loeazepan is not available in our country. Even though intravenous benzodiazepine stops seizures, intravenous antiepileptic drug (phenytoin, etc. should be administered at a loading dose. Patients with refractory status epilepticus should be supported with respect to vital, respiratory, metabolic and hemodynamic aspects and followed up in an intensive care unit to monitor cerebral electrical activity. The most common cause in the etiology is the cessation of antiepileptic drugs. The aim of SE treatment is to stop seizures and prevent complications and recurrence. In this paper, current diagnosis, treatment and etiology of SE are reviewed.

ILRS: Current Status and Future Challenges

Science.gov (United States)

Pearlman, M. R.; Bianco, G.; Merkowitz, S.; Noll, C. E.; Pavlis, E. C.; Shargorodsky, V.; Zhongping, Z.

2016-12-01

The International Laser Ranging Service (ILRS) is expanding its ground tracking capability with new stations and upgrades to current stations. Our Russian colleagues have installed new stations in Brasilia and South Africa, and have several other sites in process or in planning. The NASA Space Geodesy Program is preparing equipment for U.S. sites (McDonald and Haleakala) and with the Norwegian National Mapping Agency in Ny Ålesund; further deployments are planned. Upgrades continue at sites in China, and new sites are underway or planned in Europe and India. Stations are moving to higher repetition rates and more efficient detection to enhance satellite interleaving capability; some stations have already implemented automated processes that could lead to around-the-clock operation to increase temporal coverage and to make more efficient use of personnel. The ILRS roster of supported satellites continues to grow with the addition of the LARES satellite to augment tracking for the improvement of the ITRF. New GNSS constellations and geosynchronous satellites now bring the total roster to over 80 satellites - so much so, that new tracking strategies and time and location multiplexing are under consideration. There continues to be strong interest in Lunar Ranging. New applications of one-way and two-way laser ranging include ps-accurate time transfer, laser transponders for interplanetary ranging, and tracking of space debris. New laser ranging data products are being developed, including satellite orbit products, satellite orientation, gravity field products, and products to characterize the quality of data and station performance. This talk will give a brief summary of recent progress, current challenges and a view of the path ahead.

The Current Status of Teachers and the Teaching Profession in ...

African Journals Online (AJOL)

This paper examines the current status of teachers and the teaching sector in Tanzania. It draws on experiences of teachers, parents, and students in Dar es Salaam, Iringa and Mbeya regions. Informed by the qualitative inquiry, the paper is largely empirical in character. Data was sought through interviews and document ...

Current status and prospect of radiation technology for the safety and security of food

International Nuclear Information System (INIS)

Byun, Myung Woo

2009-01-01

Since 1960, radiation technology (RT), which had been known as the method eliminating the biologically hazardous factors of the products in the food, medical, pharmaceutical and cosmetic industries, was comprehensively investigated. The safety of food irradiation has been throughout evaluated with scientific experiments. Recently, RT has been associated with other high technologies such as biotechnology and nanotechnology, and resulted in the innovative products. Through these fusion technology with RT, the new items with high functionality and value will be shown. But, until now, consumers' acceptance on radiation is still the problem to be solved for further development. To make the consumer correctly understand RT, the benefits and defects of RT should be informed and there should be the legislated policy for the industrialization of RT by government. Therefore, this review will introduce the current status of food irradiation in the world, the safety and national agreements and the recent results from radiation fusion technology, and suggest the further work

Status of the LCLS-II Accelerating Cavity Production

Energy Technology Data Exchange (ETDEWEB)

Daly, Ed [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Marhauser, Frank [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Fitzpatrick, Jarrod A. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Palczewski, Ari D. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Preble, Joe [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Wilson, Katherine M. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Grimm, C. J. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Burrill, Andrew B. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Gonnella, Daniel [SLAC National Accelerator Lab., Menlo Park, CA (United States)

2017-05-01

Cavity serial production for the LCLS-II 4 GeV CM SRF linac has started. A quantity of 266 accelerating cavities has been ordered from two industrial vendors. Jefferson Laboratory leads the cavity procurement activities for the project and has successfully transferred the Nitrogen-Doping process to the industrial partners in the initial phase, which is now being applied for the production cavities. We report on the results from vendor qualification and the status of the cavity production for LCLS-II.

30 CFR 250.195 - What notification does MMS require on the production status of wells?

Science.gov (United States)

2010-07-01

... the well in a production status. You must confirm oral notification by telefax or e-mail within those... production status of wells? 250.195 Section 250.195 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT... Information and Reporting Requirements § 250.195 What notification does MMS require on the production status...

Current status of the 124Xe target system development for the high purity 123I production in KCCH

International Nuclear Information System (INIS)

Chun, Kwon Soo

2002-01-01

This report describes the 124 Xe gaseous target system employed for 123 I production at the Korea Cancer Center Hospital. Currently the control system is manual and will be computerized after the system parameters have been established

The Current Status of Sport Sociology within American and Canadian Colleges and Universities.

Science.gov (United States)

Brooks, Dana D.

The purpose of this study was to investigate the current status of sport sociology within American and Canadian Colleges and Universities. The study investigated: (1) the number of graduate and undergraduate courses offered in sport sociology; (2) current research area(s) of interest within sport sociology; (3) current text used as reference and…

The Halal status of additives in milk and dairy products

Directory of Open Access Journals (Sweden)

Midhat Jašić

2007-06-01

Full Text Available The market of halal products in the world keeps growing and there are more and more requests for certifying and proving the halal status of a food product. Halal in Islamic regulations means allowed for eating. Islamic laws related to the food, strictly forbid the use of food originating from pork, alcohol, blood and other products that are not in accordance with Islamic rules. In order to get the halal status, dairy products have to prove that they do not contain raw mater and additives that are forbidden. Level of allowance is related with their status which can be Halal (permitted, Haram (forbidden and Mashbuh (suspected. In establishing the system for Halal foodprocessing, proactive preventive process approach is used. In validation of the process there are analytical methods to prove the origin of the food. Specially difficult is to prove the presence of additives which during the process experience chemical transformations. The ELISA PCR, HLPC methods are used for the validation. This paper presents additives that are the most common in milk processing and can have Haram (forbidden by Islamic rules and Mashbuh (suspected origin.

Current market of industrial bio-products and biofuels, and predictable evolutions by 2015/2030. Synthesis

International Nuclear Information System (INIS)

2007-04-01

The main objectives of this study were to describe the current status of the energetic and industrial bio-product markets (biofuels, bio-lubricants, biomaterials, papers, cosmetics, and so on), to identify and analyze the evolution perspectives of these new markets on a long and medium term, to define scenarios of evolution for different sectors (agro-industry, energy, organic chemistry), to identify the most promising new markets, and to select the priority agro-industrial sectors

Corporate Blended Learning in Portugal: Current Status and Future Directions

Science.gov (United States)

Marcal, Julia; Caetano, Antonio

2010-01-01

The aim of this study is to characterize the current status of blended learning in Portugal, given that b-learning has grown exponentially in the Portuguese market over recent years. 38 organizations (representing 68% of all institutions certified to provide distance training by the Government Labour Office--DGERT-) participated in this study. The…

The current status of mango farming business in Ghana: A case ...

African Journals Online (AJOL)

The current status of mango farming business in Ghana: A case study of mango farming in the Dangme West District. ... Mango (Mangifera indica L.) is a crop which is assuming great economic importance in Ghana. ... HOW TO USE AJOL.

Market perspectives of H2 vehicles. Analysis of current status and requirements

International Nuclear Information System (INIS)

Bunzeck, I.G.

2009-06-01

This report serves as discussion document for the workshop 'Technologies for fuel cells and hydrogen in road transport' in Paris, France, March 2009. The workshop is part of the Efonet (Energy Foresight Network, www.efonet.org ) program initiated by the European Commission. As a starting point, the status quo of fuel cell technology is analyzed from an innovation perspective, compared with the current vehicle deployment in demonstration projects worldwide. Then, cost reductions of fuel cell and drive train components that can be achieved as function over time are modelled in a learning curve approach. This provides a forecast on the expected vehicle cost by cumulative production, enabling discussion on the connection between necessary vehicle deployment and current demonstration projects, also in respect to project finance. Within the EU HyWays project, four scenarios have been developed to model the penetration rates for hydrogen vehicles in transport. All scenarios are determined by two influencing factors, policy support and level of technological learning. Depending on the scenario, it is assumed that mass production of vehicles starts either by 2013 (2016) with a group of 5 (4) first movers that achieve up to 90% plant utilization in different time frames. Given the bandwidth of scenario results, it is possible to redefine cost targets and provide recommendations for the necessary policy support. The report also provides an assessment of current hydrogen vehicle RD and D activities by different OEMs and gives an indication on the expected market entry strategies and time frame. To conclude, cost of conventional and hydrogen vehicles are compared on a euro/km level, testing several policy measures for their suitability to lower the expected high vehicle cost for the end-consumer.

Current and past menstrual status is an important determinant of femoral neck geometry in exercising women.

Science.gov (United States)

Mallinson, Rebecca J; Williams, Nancy I; Gibbs, Jenna C; Koehler, Karsten; Allaway, Heather C M; Southmayd, Emily; De Souza, Mary Jane

2016-07-01

Menstrual status, both past and current, has been established as an important determinant of bone mineral density (BMD) in young exercising women. However, little is known regarding the association between the cumulative effect of menstrual status and indices of bone health beyond BMD, such as bone geometry and estimated bone strength. This study explores the association between cumulative menstrual status and indices of bone health assessed using dual-energy x-ray absorptiometry (DXA), including femoral neck geometry and strength and areal BMD (aBMD), in exercising women. 101 exercising women (22.0±0.4years, BMI 21.0±0.2kg/m(2), 520±40min/week of self-reported exercise) participated in this cross-sectional study. Women were divided into three groups as follows based on their self-reported current and past menstrual status: 1) current and past regular menstrual cycles (C+P-R) (n=23), 2) current and past irregular menstrual cycles (C+P-IR) (n=56), 3) and current or past irregular cycles (C/P-RIR) (n=22). Current menstrual status was confirmed using daily urinary metabolites of reproductive hormones. DXA was used to assess estimates of femoral neck geometry and strength from hip strength analysis (HSA), aBMD, and body composition. Cross-sectional moment of inertia (CSMI), cross-sectional area (CSA), strength index (SI), diameter, and section modulus (Z) were calculated at the femoral neck. Low CSMI, CSA, SI, diameter, and Z were operationally defined as values below the median. Areal BMD (g/cm(2)) and Z-scores were determined at the lumbar spine, femoral neck, and total hip. Low BMD was defined as a Z-score0.05). However, after controlling for confounding variables, cumulative menstrual status was not a significant predictor of low aBMD. In exercising women, the cumulative effect of current and past menstrual irregularity appears to be an important predictor of lower estimates of femoral neck geometry, as observed by smaller CSMI and CSA, which may serve as an

Thermoelectric microgenerators. Current status and prospects of application

Directory of Open Access Journals (Sweden)

Strutynska L. T.

2008-08-01

Full Text Available Analysis of current status and prospects of using thermoelectric microgenerators, including organic-fueled ones, is performed. Developments of thermoelectric microgenerators presented in this review demonstrate that their increasingly wide use forms a separate, very important line of thermoelectricity – micropower generation with growing potential of practical applications for charging batteries, mobile phones, digital cameras and photocameras, power supply to small radio stations, other portable devices, including medical. The ways of increasing the efficiency of such devices and relevant lines of their wide use in practice are determined.

Current status of the nuclear medicine in Japan

International Nuclear Information System (INIS)

Torizuka, K.

1974-01-01

A brief survey of the current status of Japan nuclear medicine is given. The following data are described (from the material of the 11th Japan Conference of Radioisotopes): 1. the increase of the number of nuclear instruments between 1971 and 1973; 2. the total amount of the cobalt radiation apparatur (inclusive of the cesium apparatus) in the hospitals in 1971- and 1972; 3. the radioactive medicines and nuclids used in Japan; 4. the radioactive isotopes used generally in the therapeutics in 1971 and 1972; 5. the question of labour. (K.A.)

Relationships between neighbourhood characteristics and current STI status among HIV-infected and HIV-uninfected women living in the Southern USA: a cross-sectional multilevel analysis.

Science.gov (United States)

Haley, Danielle F; Kramer, Michael R; Adimora, Adaora A; Haardörfer, Regine; Wingood, Gina M; Ludema, Christina; Rubtsova, Anna; Hickson, DeMarc A; Ross, Zev; Golub, Elizabeth; Bolivar, Hector; Cooper, Hannah Lf

2017-12-01

Neighbourhood characteristics (eg, high poverty rates) are associated with STIs among HIV-uninfected women in the USA. However, no multilevel analyses investigating the associations between neighbourhood exposures and STIs have explored these relationships among women living with HIV infection. The objectives of this study were to: (1) examine relationships between neighbourhood characteristics and current STI status and (2) investigate whether the magnitudes and directions of these relationships varied by HIV status in a predominantly HIV-infected cohort of women living in the Southern USA. This cross-sectional multilevel analysis tests relationships between census tract characteristics and current STI status using data from 737 women enrolled at the Women's Interagency HIV Study's southern sites (530 HIV-infected and 207 HIV-uninfected women). Administrative data (eg, US Census) described the census tract-level social disorder (eg, violent crime rate) and social disadvantage (eg, alcohol outlet density) where women lived. Participant-level data were gathered via survey. Testing positive for a current STI was defined as a laboratory-confirmed diagnosis of chlamydia, gonorrhoea, trichomoniasis or syphilis. Hierarchical generalised linear models were used to determine relationships between tract-level characteristics and current STI status, and to test whether these relationships varied by HIV status. Eleven per cent of participants tested positive for at least one current STI. Greater tract-level social disorder (OR=1.34, 95% CI 0.99 to 1.87) and social disadvantage (OR=1.34, 95% CI 0.96 to 1.86) were associated with having a current STI. There was no evidence of additive or multiplicative interaction between tract-level characteristics and HIV status. Findings suggest that neighbourhood characteristics may be associated with current STIs among women living in the South, and that relationships do not vary by HIV status. Future research should establish the

Cacao biotechnology: current status and future prospects.

Science.gov (United States)

Wickramasuriya, Anushka M; Dunwell, Jim M

2018-01-01

Theobroma cacao-The Food of the Gods, provides the raw material for the multibillion dollar chocolate industry and is also the main source of income for about 6 million smallholders around the world. Additionally, cocoa beans have a number of other nonfood uses in the pharmaceutical and cosmetic industries. Specifically, the potential health benefits of cocoa have received increasing attention as it is rich in polyphenols, particularly flavonoids. At present, the demand for cocoa and cocoa-based products in Asia is growing particularly rapidly and chocolate manufacturers are increasing investment in this region. However, in many Asian countries, cocoa production is hampered due to many reasons including technological, political and socio-economic issues. This review provides an overview of the present status of global cocoa production and recent advances in biotechnological applications for cacao improvement, with special emphasis on genetics/genomics, in vitro embryogenesis and genetic transformation. In addition, in order to obtain an insight into the latest innovations in the commercial sector, a survey was conducted on granted patents relating to T. cacao biotechnology. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

Proteomics of Important Food Crops in the Asia Oceania Region: Current Status and Future Perspectives

KAUST Repository

Chakraborty, Subhra; Salekdeh, Ghasem Hosseini; Yang, Pingfang; Woo, Sun-Hee; Chin, Chiew Foan; Gehring, Christoph A; Haynes, Paul A.; Mirzaei, Mehdi; Komatsu, Setsuko

2015-01-01

In the rapidly growing economies of Asia and Oceania, food security has become a primary concern. With the rising population, growing more food at affordable prices is becoming even more important. In addition, the predicted climate change will lead to drastic changes in global surface temperature and changes in rainfall patterns that in turn would pose a serious threat to plant vegetation worldwide. As a result, understanding how plants will survive in a changing climate will be increasingly important. Such challenges require integrated approaches to increase agricultural production and cope with environmental threats. Proteomics can play a role in unravel the underlying mechanisms for food production to address the growing demand for food. In this review, the current status of food crop proteomics is discussed, especially in regards to the Asia and Oceania regions. Furthermore, the future perspective in relation to proteomic techniques for the important food crops is highlighted.

Proteomics of Important Food Crops in the Asia Oceania Region: Current Status and Future Perspectives

KAUST Repository

Chakraborty, Subhra

2015-06-02

In the rapidly growing economies of Asia and Oceania, food security has become a primary concern. With the rising population, growing more food at affordable prices is becoming even more important. In addition, the predicted climate change will lead to drastic changes in global surface temperature and changes in rainfall patterns that in turn would pose a serious threat to plant vegetation worldwide. As a result, understanding how plants will survive in a changing climate will be increasingly important. Such challenges require integrated approaches to increase agricultural production and cope with environmental threats. Proteomics can play a role in unravel the underlying mechanisms for food production to address the growing demand for food. In this review, the current status of food crop proteomics is discussed, especially in regards to the Asia and Oceania regions. Furthermore, the future perspective in relation to proteomic techniques for the important food crops is highlighted.

Controlling the HIV/AIDS epidemic: current status and global challenges

Directory of Open Access Journals (Sweden)

Thorsten eDemberg

2012-08-01

Full Text Available This review provides an overview of the current status of the global HIV pandemic and strategies to bring it under control. It updates numerous preventive approaches including behavioral interventions, male circumcision, pre- and post-exposure prophylaxis, vaccines, and microbicides. The manuscript summarizes current anti-retroviral treatment options, their impact in the western world, and difficulties faced by emerging and resource-limited nations in providing and maintaining appropriate treatment regimens. Current clinical and pre-clinical approaches towards a cure for HIV are described, including new drug compounds that target viral reservoirs and gene therapy approaches aimed at altering susceptibility to HIV infection. Recent progress in vaccine development is summarized, including novel approaches and new discoveries.

The Current Status of Classroom Inclusion Activities of Secondary Agriculture Teachers

Science.gov (United States)

Hoerst, Caryn M.; Whittington, M. Susie

2009-01-01

The current status of classroom inclusion activities among agriculture teachers in comprehensive secondary agricultural education programs in Ohio is reported. The researchers describe secondary agriculture teachers' needs related to teaching learners with special needs in inclusion classes, given legislative mandates. Specifically, the…

Production and properties of the heaviest elements. Status and perspectives

International Nuclear Information System (INIS)

Backe, H.; Hebberger, F.P.; Sewtz, M.; Turler, A.

2007-01-01

This article reviews the following topics which were discussed at the Workshop on the Atomic Properties of the Heaviest Elements held from September 25-27, 2006 in Chiemsee, Germany: (i) the recent progress in the production of the heaviest elements, the investigation of their nuclear structure, and prospects for direct mass measurements in Penning traps; (ii) recent studies of their chemical properties with the aid of volatile species and single-atom aqueous-phase chemistry; (iii) the current status and future prospects for the investigation of atomic and ionic properties such as optical spectroscopy in gas cells and ion traps, including fully relativistic calculations of the atomic level structure with predictions for the element nobelium; and (iv) ionic charge radii measurements in buffer gas filled drift cells, and ion chemical reactions in the gas phase. (authors)

Study of Grants, new Mexico, uranium miners: current status

International Nuclear Information System (INIS)

Samet, J.M.; Morgan, M.V.; Buechley, R.W.; Key, C.R.; Valdivia, A.A.

1981-01-01

The Uranium Epidemiology Study at the University of New Mexico was initiated in 1977 with the objective of assessing health effects of uranium mining in the Grants, New Mexico, area. The planned approach was a cohort study of mortality that would capitalize on the availability of health records at the Grants Clinic. The first year's work confirmed the study's feasibility (Buechley, 1979). Subsequent efforts have focused on the health and exposure data base and comprehensive follow-up. A retrospective cohort study of early miners is in progress; a prospective cohort study of miners who began working under the current federal standard is planned. This report will summarize the current status of the Uranium Epidemiology Study

Curriculum leadership in the postgraduate: Gap between current and optimal status.

Science.gov (United States)

Avizhgan, Maryam; Jafari, Ebrahim Mirshah; Nasr, Ahmad Reza; Changiz, Tahereh

2015-04-01

Identifying the strengths and weakness points is one of the effective methods to analyze current status, and prioritizing actions based on the gap between current and optimal status is necessary for short-term and long-term planning in departments and colleges. The aim of this study was to determine the gap between current and optimal status of curriculum leadership in the postgraduate courses in two Iranian universities. In this cross-sectional study, a sample of 212 faculty members from the two Iranian universities (one medical and one nonmedical) was randomly selected through stratified random sampling method. Data were collected by using a researcher-made questionnaire, with 55 items categorized in four areas of main dimensions in curriculum leadership. The validity of the questionnaire was determined by curriculum studies scholars, and the reliability was confirmed as the Cronbach's alpha calculated 0.969. Data were analyzed using descriptive and inferential statistics according to the variables. There was a gap in all dimensions and roles. The maximum gap (-1.70) with the highest frequency (98%) were related to "improving the educational atmosphere" dimension. As for items, the maximum gap (-2.41) was related to "society needs and expectations and the labor market" in "curriculum development and revision" dimension. The negative gap between all dimensions of curriculum leadership implies faculty members' dissatisfaction. Curriculum leadership at universities, colleges and departments of the study in all aspects need to be improved. Hence, it is necessary for managers to make use of the viewpoints of the faculty members to decrease the gap.

Cereal production, high status and climate in Medieval Iceland

Science.gov (United States)

Erlendsson, Egill; Riddell, Scott

2017-04-01

At Hrísbrú (formerly the medieval Mosfell estate) in the Mosfell Valley, southwest Iceland, archaeologists have excavated a medieval skáli (hall) proposed to be the high status residence of a chieftain. This is indicated by the size of the skáli, artefacts (foreign goods), archaeofaunal (cattle/sheep bone) ratios and macrobotanical remains (cereal grain). The analysis of pollen from nearby natural contexts suggests that cereals were grown locally. Using multiple profile palynological approach, this paper examines if the apparent cereal production is representative of high status in the Icelandic context. First as a correlate by confirming that cereals were grown in association with the archaeological features characteristic of high status; secondly, as an indicator in its own right through comparison with other palynological datasets from inferred lower status farms. The presence or absence of cereal-type pollen (cf. barley) and other arable correlates was examined for each site. The results suggest that medieval cereal cultivation in the Mosfell Valley was confined to the landholding of the medieval Mosfell estate. This feature is seen as an attribute of the locale's greater status in relation to the other farms in Mosfell Valley. The abandonment of cereal cultivation at the Mosfell estate around AD 1200 is probably associated with interactions between changes in the nation's social power structure and how marginal cereal production in Iceland was (and is) in terms of climate.

Current status of technology development for fabrication of Indian Test Blanket Module (TBM) of ITER

Energy Technology Data Exchange (ETDEWEB)

Jayakumar, T., E-mail: tjk@igcar.gov.in [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research (IGCAR), Kalpakkam 603102 (India); Rajendra Kumar, E. [TBM Division, Institute for Plasma Research (IPR), Bhat, Gandhinagar 382428 (India)

2014-10-15

Highlights: • Status of technology developments for Indian TBM to be installed in ITER is presented. • Procedure development for EB, laser and laser-hybrid welding of RAFM steel presented. • Filler wires for RAFM steel for TIG, NG-TIG and laser-hybrid welding have been developed. • Feasibility of production of channel plate by HIP technology has been demonstrated. - Abstract: Ever since India decided to install its Lead-Lithium Ceramic Breeder (LLCB) TBM in ITER, various technologies for fabrication of Indian TBM are being pursued by IPR and IGCAR, in collaboration with various research laboratories in India. Welding consumables for joining India specific RAFM steels (IN-RAFMS), procedures for hot isostatic pressing, electron beam welding, laser and laser-hybrid welding have been developed. Considering the complex nature and limited access available for inspection, innovative inspection procedures that involved use of phased array ultrasonic and C-scan imaging are also being pursued. This paper presents the current status of these developments and provides a roadmap for the future activities planned in realizing Indian TBM for testing in ITER.

Prognostics and Health Management of Wind Turbines: Current Status and Future Opportunities

Energy Technology Data Exchange (ETDEWEB)

Sheng, Shuangwen

2016-10-04

This presentation was given at the 2016 Annual Conference of the Prognostics and Health Management Society. It covers the current status and challenges and opportunities of prognostics and health management of wind turbines.

Current status and perspectives of cysticercosis and taeniasis in Japan.

Science.gov (United States)

Yamasaki, Hiroshi

2013-02-01

This mini-review describes recent epidemiological trends in cysticercosis and taeniasis in Japan. Some of the topics discussed herein were presented at the first symposium on "Current perspectives of Taenia asiatica researches", that was held in Osong in Chungbuk Province, South Korea, in October 2011 and organized by Prof. K. S. Eom, Chungbuk National University School of Medicine. To better understand the trends in the occurrence of cysticercosis and taeniasis in Japan, clinical cases reported in 2005 have been updated. In addition, the current status of Taenia asiatica infections successively occurring in Japan since 2010 is also discussed.

Current status of studies on temperature fluctuation phenomena in LMFRs

International Nuclear Information System (INIS)

Ohshima, H.; Muramatsu, T.; Kobayashi, J.; Yamaguchi, A.

1994-01-01

This paper describes the current status of studies being performed in PNC on temperature fluctuation phenomena occurring in fast reactors. The studies concentrate on four problems: thermal stratification, thermal striping, core-plenum interaction and free surface sloshing. Both experimental and analytical approaches to reveal these phenomena and to establish design and safety evaluation methods are presented together with future works. (author)

MONK and MCBEND: Current status and recent developments

International Nuclear Information System (INIS)

Richards, Simon D.; Baker, Chris M.J.; Bird, Adam J.; Cowan, Pat; Davies, Nigel; Dobson, Geoff P.; Fry, Tim C.; Kyrieleis, Albrecht; Smith, Paul N.

2015-01-01

Highlights: • We describe recent developments to the Monte Carlo codes MONK and MCBEND. • MONK is a Monte Carlo code for nuclear criticality and reactor physics analyses. • MCBEND is a Monte Carlo code for radiation shielding and dosimetry analyses. • Improvements include input; physics; scoring; variance reduction; and visualisation. • Parallelisation of MONK and multi-physics coupling are described. - Abstract: MONK® and MCBEND are Monte Carlo software packages for: nuclear criticality and reactor physics; and radiation shielding and dosimetry applications, respectively. The codes are actively developed, maintained and supported by AMEC’s ANSWERS® Software Service in line with the ANSWERS vision of providing easy-to-use software that meets the current and emerging needs of the user community. This paper summarises the current status of MONK and MCBEND and the recent developments which have been carried out to the codes, and their supporting nuclear data libraries and visualisation package

Polycystic ovary syndrome: current status and future perspective

Science.gov (United States)

Barthelmess, Erin K.; Naz, Rajesh K.

2015-01-01

Polycystic ovary syndrome (PCOS) is a widespread reproductive disorder that encompasses many associated health conditions and has an impact on various metabolic processes. PCOS is depicted by hyperandrogenism, polycystic ovaries, and anovulation. It increases the risk of insulin resistance (IR), type 2 diabetes, obesity, and cardiovascular disease. The etiology of the disease remains unclear, and the subjective phenotype makes a united diagnosis difficult among physicians. It seems to be a familial genetic syndrome caused by a combination of environmental and genetic factors. It can be linked with metabolic disorders in first-degree family members. PCOS is the cause of up to 30% of infertility in couples seeking treatment. Currently, there is no cure for PCOS. Despite the growing incidence of this syndrome, limited research has been done that encompasses the entirety of PCOS spectrum. In this review, the current status and possible future perspective will be discussed. PMID:24389146

Measuring Earth: Current status of the GRACE Follow-On Laser Ranging Interferometer

Science.gov (United States)

Schütze, Daniel; LRI Team

2016-05-01

The GRACE mission that was launched in 2002 has impressively proven the feasibility of low-orbit satellite-to-satellite tracking for Earth gravity observations. Especially mass transport related to Earth's hydrological system could be well resolved both spatially and temporally. This allows to study processes such as polar ice sheet decline and ground water depletion in great detail. Owing to GRACE's success, NASA and GFZ will launch the successor mission GRACE Follow-On in 2017. In addition to the microwave ranging system, GRACE Follow-On will be the first mission to use a Laser Ranging Interferometer as technology demonstrator to track intersatellite distance changes with unprecedented precision. This new ranging device inherits some of the technologies which have been developed for the future spaceborne gravitational wave detector LISA. I will present the architecture of the Laser Ranging Interferometer, point out similarities and differences to LISA, and conclude with the current status of the flight hardware production.

Current status of endoscopic simulation in gastroenterology fellowship training programs.

Science.gov (United States)

Jirapinyo, Pichamol; Thompson, Christopher C

2015-07-01

Recent guidelines have encouraged gastroenterology and surgical training programs to integrate simulation into their core endoscopic curricula. However, the role that simulation currently has within training programs is unknown. This study aims to assess the current status of simulation among gastroenterology fellowship programs. This questionnaire study consisted of 38 fields divided into two sections. The first section queried program directors' experience on simulation and assessed the current status of simulation at their institution. The second portion surveyed their opinion on the potential role of simulation on the training curriculum. The study was conducted at the 2013 American Gastroenterological Association Training Directors' Workshop in Phoenix, Arizona. The participants were program directors from Accreditation Council for Graduate Medical Education accredited gastroenterology training programs, who attended the workshop. The questionnaire was returned by 69 of 97 program directors (response rate of 71%). 42% of programs had an endoscopic simulator. Computerized simulators (61.5%) were the most common, followed by mechanical (30.8%) and animal tissue (7.7%) simulators, respectively. Eleven programs (15%) required fellows to use simulation prior to clinical cases. Only one program has a minimum number of hours fellows have to participate in simulation training. Current simulators are deemed as easy to use (76%) and good educational tools (65%). Problems are cost (72%) and accessibility (69%). The majority of program directors believe that there is a need for endoscopic simulator training, with only 8% disagreeing. Additionally, a majority believe there is a role for simulation prior to initiation of clinical cases with 15% disagreeing. Gastroenterology fellowship program directors widely recognize the importance of simulation. Nevertheless, simulation is used by only 42% of programs and only 15% of programs require that trainees use simulation prior to

Current status in Japan related to LMNPP

International Nuclear Information System (INIS)

Otsuka, Takehiro

1998-01-01

Current status of nuclear power plants in Japan is presented with the basic concepts against ageing of LWR plants which are considered to continue growing into the 21st century. Life management for aged NPPs is recognized to be important for the safe and reliable operation. In April 1996 MITI published the first report regarding the measures to cope with the aged NPPs. Two BWRs and one PWR were evaluated as aged NPPs in Phase-I Technical evaluation, which concluded that safe operation is possible with correct and adequate maintenance despite operation exceeded 30 years. The technology development items towards attaining further highly reliable management were indicated including the inspection/monitoring technology, the preventive maintenance/repair technology and ageing evaluation technology

Challenges and status of ITER conductor production

International Nuclear Information System (INIS)

Devred, A; Backbier, I; Bessette, D; Bevillard, G; Gardner, M; Jong, C; Lillaz, F; Mitchell, N; Romano, G; Vostner, A

2014-01-01

Taking the relay of the large Hadron collider (LHC) at CERN, ITER has become the largest project in applied superconductivity. In addition to its technical complexity, ITER is also a management challenge as it relies on an unprecedented collaboration of seven partners, representing more than half of the world population, who provide 90% of the components as in-kind contributions. The ITER magnet system is one of the most sophisticated superconducting magnet systems ever designed, with an enormous stored energy of 51 GJ. It involves six of the ITER partners. The coils are wound from cable-in-conduit conductors (CICCs) made up of superconducting and copper strands assembled into a multistage cable, inserted into a conduit of butt-welded austenitic steel tubes. The conductors for the toroidal field (TF) and central solenoid (CS) coils require about 600 t of Nb 3 Sn strands while the poloidal field (PF) and correction coil (CC) and busbar conductors need around 275 t of Nb–Ti strands. The required amount of Nb 3 Sn strands far exceeds pre-existing industrial capacity and has called for a significant worldwide production scale up. The TF conductors are the first ITER components to be mass produced and are more than 50% complete. During its life time, the CS coil will have to sustain several tens of thousands of electromagnetic (EM) cycles to high current and field conditions, way beyond anything a large Nb 3 Sn coil has ever experienced. Following a comprehensive R and D program, a technical solution has been found for the CS conductor, which ensures stable performance versus EM and thermal cycling. Productions of PF, CC and busbar conductors are also underway. After an introduction to the ITER project and magnet system, we describe the ITER conductor procurements and the quality assurance/quality control programs that have been implemented to ensure production uniformity across numerous suppliers. Then, we provide examples of technical challenges that have been

Challenges and status of ITER conductor production

Science.gov (United States)

Devred, A.; Backbier, I.; Bessette, D.; Bevillard, G.; Gardner, M.; Jong, C.; Lillaz, F.; Mitchell, N.; Romano, G.; Vostner, A.

2014-04-01

Taking the relay of the large Hadron collider (LHC) at CERN, ITER has become the largest project in applied superconductivity. In addition to its technical complexity, ITER is also a management challenge as it relies on an unprecedented collaboration of seven partners, representing more than half of the world population, who provide 90% of the components as in-kind contributions. The ITER magnet system is one of the most sophisticated superconducting magnet systems ever designed, with an enormous stored energy of 51 GJ. It involves six of the ITER partners. The coils are wound from cable-in-conduit conductors (CICCs) made up of superconducting and copper strands assembled into a multistage cable, inserted into a conduit of butt-welded austenitic steel tubes. The conductors for the toroidal field (TF) and central solenoid (CS) coils require about 600 t of Nb3Sn strands while the poloidal field (PF) and correction coil (CC) and busbar conductors need around 275 t of Nb-Ti strands. The required amount of Nb3Sn strands far exceeds pre-existing industrial capacity and has called for a significant worldwide production scale up. The TF conductors are the first ITER components to be mass produced and are more than 50% complete. During its life time, the CS coil will have to sustain several tens of thousands of electromagnetic (EM) cycles to high current and field conditions, way beyond anything a large Nb3Sn coil has ever experienced. Following a comprehensive R&D program, a technical solution has been found for the CS conductor, which ensures stable performance versus EM and thermal cycling. Productions of PF, CC and busbar conductors are also underway. After an introduction to the ITER project and magnet system, we describe the ITER conductor procurements and the quality assurance/quality control programs that have been implemented to ensure production uniformity across numerous suppliers. Then, we provide examples of technical challenges that have been encountered and

Current status and technology development tendency of research reactors in china

International Nuclear Information System (INIS)

Ke Guotu; Shen Feng; Zhao Shouzhi; Zhang Weiguo; Yuan Luzheng

2009-01-01

The current status and development history of domestic and abroad research reactors (RRs) are mentioned. The representative RRs and their respective technology characteristics are introduced. The utilizations of China's RRs, mainly included as nuclear engineering technology, basic research applications of nuclear technology, teaching and personnel training, are explained. (authors)

The association between alcohol exposure and self-reported health status: the effect of separating former and current drinkers.

Directory of Open Access Journals (Sweden)

Wenbin Liang

Full Text Available To investigate the direction and degree of potential bias introducedto analyses of drinking and health status which exclude former drinkers from exposure groups.Pooled analysis of 14 waves (1997-2010 of the U.S. National Health Interview Survey (NHIS.General population-based study.404,462 participants, from 14 waves of the NHIS, who had knownself-reported health status and alcohol consumption status.Self-reported health status was used as the indicatorof health. Two approaches were used to classify alcohol consumption: (i separation of former drinkers and current drinkers, and (ii combined former and current drinkers. The prevalence of fair/poor health by alcohol use, gender and age with 95% confidence intervals was estimated. The difference in prevalence of fair/poor health status for lifetime abstainers, former drinkers, current drinkers and drinkers (former drinkers and current drinkers combined were compared using Poisson regression with robust estimations of variance.Excluding former drinkers from drinker groups exaggerates the difference in health status between abstainers and drinkers, especially for males.In cohort study analyses, former drinkers should be assigned to a drinking category based on their previous alcohol consumption patterns and not treated as a discrete exposure group.

Marine renewable energy in China: Current status and perspectives

OpenAIRE

Yong-liang Zhang; Zheng Lin; Qiu-lin Liu

2014-01-01

Based on a general review of marine renewable energy in China, an assessment of the development status and amount of various marine renewable energy resources, including tidal energy, tidal current energy, wave energy, ocean thermal energy, and salinity gradient energy in China's coastal seas, such as the Bohai Sea, the Yellow Sea, the East China Sea, and the South China Sea, is presented. We have found that these kinds of marine renewable energy resources will play an important role in meeti...

Current status of quality assurance of treatment planning systems

International Nuclear Information System (INIS)

Mijnheer, B.J.

1997-01-01

A review is given of the current status of quality assurance of treatment planning systems. At this moment only one comprehensive report is available. In order to review national activities a questionnaire has been distributed amongst national societies of medical physicists. From the 23 responding countries, 8 indicated that only limited efforts are underway, 8 answered that a working group is evaluating their specific national requirements while in 5 countries a document is drafted. The highlights of these reports have been summarized. (author)

Oil development in China: Current status and future trends

International Nuclear Information System (INIS)

Ma Linwei; Fu Feng; Li Zheng; Liu Pei

2012-01-01

The future of oil has become an important topic of the discussion of energy policy in China. This paper attempts to present a full picture of the current status and future trends of China’s oil development through system analysis. First, we map a Sankey diagram of China’s oil flow to reveal the physical pattern of China’s oil supply and consumption. Then, we present the historical and ongoing trends of China’s oil flow from key aspects such as oil demand, oil resource availability, technology improvement, and policy adjustment. Based on these understandings, we design three scenarios of China’s oil demand in 2030, and analyze policy implications for oil saving, automotive energy development, and energy security. From the analysis, we draw some conclusions for policy decisions, such as to control the total oil consumption to avoid energy security risks, to enhance oil saving in all sectors with road transportation as the emphasis, and to increase the investment on oil production and refining to secure oil supply and reduce emissions. - Highlights: ► A Sankey Diagram to reveal the physical pattern of China’s oil supply and consumption. ► Present the ongoing trends of China’s oil development. ► Discuss important policy issues such as oil saving, energy security, and emissions reduction.

Current status of accelerator-based boron neutron capture therapy

International Nuclear Information System (INIS)

Kreiner, A. J.; Bergueiro, J.; Di Paolo, H.; Castell, W.; Vento, V. Thatar; Cartelli, D.; Kesque, J.M.; Valda, A.A.; Ilardo, J.C.; Baldo, M.; Erhardt, J.; Debray, M.E.; Somacal, H.R.; Estrada, L.; Sandin, J.C. Suarez; Igarzabal, M.; Huck, H.; Padulo, J.; Minsky, D.M.

2011-01-01

The direct use of proton and heavy ion beams for radiotherapy is a well established cancer treatment modality, which is becoming increasingly widespread due to its clear advantages over conventional photon-based treatments. This strategy is suitable when the tumor is spatially well localized. Also the use of neutrons has a long tradition. Here Boron Neutron Capture Therapy (BNCT) stands out, though on a much smaller scale, being a second-generation promising alternative for tumors which are diffuse and infiltrating. On this sector, so far only nuclear reactors have been used as neutron sources. In this paper we describe the current situation worldwide as far as the use of accelerator-based neutron sources for BNCT is concerned (so-called Accelerator-Based (AB)-BNCT). In particular we discuss the present status of an ongoing project to develop a folded Tandem-ElectroStatic-Quadrupole (TESQ) accelerator at the Atomic Energy Commission of Argentina. The project goal is a machine capable of delivering 30 mA of 2.4 MeV protons to be used in conjunction with a neutron production target based on the 7 Li(p,n) 7 Be reaction. These are the specifications needed to produce sufficiently intense and clean epithermal neutron beams to perform BNCT for deep-seated tumors in less than an hour. (author)

Blueberry production in Chile: current status and future developments

Directory of Open Access Journals (Sweden)

Jorge B. Retamales

2014-03-01

Full Text Available Chile has become a major actor in the blueberry industry as the most important supplier of off-season fresh fruit for the northern hemisphere. Blueberry exports passed from US$ 30 million (around 4,000 tons in 2000 to US$ 380 million (94,000 tons in 2011. The characteristics of the major blueberry growing regions (North, Central, South-central and South are presented in terms of acreage, varieties, management practices, extension of the harvest season, and soil and climatic conditions. Most fruit is from highbush varieties, picked by hand and exported fresh by boat to United States. Largest proportion of fruit is exported from mid December to late January, which coincides with lowest prices. The south-central region (latitudes 34º50' to 38º15' S was in 2007 the most important one with 5,075 ha (51.1% of area planted. Among the challenges for the Chilean blueberry industry in the near future are: 1. Lower profitability due to lower rates of currency exchange and higher costs, 2 - Greater scarcity and higher cost of labor, 3.- Need for higher productivity and sustainable production practices, 4- Fruit of high and consistent quality, and 5.- Greater investment in research. As a case study the article presents three approaches that can help identify areas with low availability of labor and improve its efficiency. The article shows the use of geomatic tools to establish labor availability, application of growth regulators to reduce crop load, increase fruit size and improve harvest efficiency, and the use of shakers to harvest fresh fruit for long distance markets. More research is needed to improve yields, reduce costs and give greater economical and ecological sustainability to the Chilean blueberry industry.

Nuclear liability legislation in Russia - current status and expected developments

International Nuclear Information System (INIS)

Karpov, A. E.; Borisov, D. G.

2000-01-01

Present report is provided by the experts of the Russian insurance business, a company member of the Russian Nuclear Pool, and not the experts of the Ministry of Atomic Energy of Russian Federation (RF Minatom). Considering the above, the following document will outline the current status of nuclear liability legislation and insurance in Russia from a viewpoint of the insurance companies and not RF Minatom. (author)

Production of microbial biosurfactants: Status quo of rhamnolipid and surfactin towards large-scale production.

Science.gov (United States)

Henkel, Marius; Geissler, Mareen; Weggenmann, Fabiola; Hausmann, Rudolf

2017-07-01

Surfactants are an important class of industrial chemicals. Nowadays oleochemical surfactants such as alkyl polyglycosides (APGs) become increasingly important. This trend towards the utilization of renewable resources continues and consumers increasingly demand for environmentally friendly products. Consequently, research in microbial surfactants has drastically increased in the last years. While for mannosylerythritol lipids and sophorolipids established industrial processes exist, an implementation of other microbially derived surfactants has not yet been achieved. Amongst these biosurfactants, rhamnolipids synthesized by Pseudomonas aeruginosa and surfactin produced by Bacillus subtilis are so far the most analyzed biosurfactants due to their exceptional properties and the concomitant possible applications. In this review, a general overview is given regarding the current status of biosurfactants and benefits attributed to these molecules. Furthermore, the most recent research approaches for both rhamnolipids and surfactin are presented with respect to possible methods for industrial processes and the occurring drawbacks and limitations researchers have to address and overcome. Copyright © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Current status of radiation transport tools for proliferation and terrorism prevention

International Nuclear Information System (INIS)

Sale, K.E.

2004-01-01

Full text: We will present the current status and future plans for the set of calculational tools and databases developed and maintained at LLNL. The calculational tools include the Monte Carlo codes TART 1) and COG 2) as well as the deterministic code ARDRA 3) . In addition to these codes we use currently there is a major development effort for a new massively parallel transport code. An important part of the capability we're developing is a sophisticated user interface, based on a commercial 3-D modeling product, to improve the model development process. A major part of this user interface tool is being developed by Strela 4) under the Nuclear Cities Initiative. Strela has developed a hub-and-spoke technology for code input interconversions (between COG, TART and MCNP) and will produce the plug-ins that extend the capabilities of the 3-D modeler for use as a radiation transport input generator. The major advantages of this approach are the built-in user interface for 3-D modeling and the ability to read a large variety of CAD-file formats. In addition to supporting our current radiation transport codes and developing new capabilities we are working on some nuclear data needs for homeland security. These projects are carried out and the Lawrence Berkeley National Laboratory 88' cyclotron and at the Institute for Nuclear Research of the Nation Academy of Science of Ukraine under and STCU contract. Reference: 1. http://www.llnl.gov/cullen1/mc/htm; 2. http://www-phys.llnl.gov/N_Div/COG/ETR/ETR_9306.html; 3. http://www.llnl.gov/CASC/asciturb/talks/PPT-HTML.131596/tsld030.htm; 4. http://strela.snz.ru/

Comparing the contributions of well-being and disease status to employee productivity.

Science.gov (United States)

Gandy, William M; Coberley, Carter; Pope, James E; Wells, Aaron; Rula, Elizabeth Y

2014-03-01

To compare employee overall well-being to chronic disease status, which has a long-established relationship to productivity, as relative contributors to on-the-job productivity. Data from two annual surveys of three companies were used in longitudinal analyses of well-being as a predictor of productivity level and productivity change among 2629 employees with diabetes or without any chronic conditions. Well-being was the most significant predictor of productivity cross-sectionally in a model that included disease status and demographic characteristics. Longitudinally, changes in well-being contributed to changes in productivity above and beyond what could be explained by the presence of chronic disease or other fixed characteristics. These findings support the use of well-being as the broader framework for understanding, explaining, and improving employee productivity in both the healthy and those with disease.

Summary of the Current Status of Lessons Learned From Fukushima Accident

International Nuclear Information System (INIS)

Pasamehmetoglu, Kemal

2013-01-01

This presentation introduced the current status of the lessons learned from the Fukushima accident, and in particular, the recommendations released by a NRC Near-term Task Force to enhance reactor safety in the 21. century. The near-term recommendations are focused on emergency power and emergency cooling availability during station blackout accidents

Elementary particle physics and cosmology: current status and prospects

International Nuclear Information System (INIS)

Rubakov, Valerii A

1999-01-01

The current status of elementary particle physics can be briefly summarized as follows: the Standard Model of elementary particles is perfectly (at the level of radiation effects!) adequate in describing all the available experimental data except for the recent indications of neutrino oscillations. At the same time, much (and possibly most) of today's cosmology is not encompassed by the Standard Model - a fact which, together with intrinsic theoretical difficulties and the neutrino oscillation challenge, strongly indicates that the Standard Model is incomplete. It is expected that in the current decade a 'new physics', i.e. particles and interactions beyond the Standard Model, will emerge. Major advances in cosmology, both in terms of qualitatively improved observations and theoretical analysis of the structure and evolution of the Universe, are expected as well. (special issue)

STATUS OF PUMPKIN SEED PRODUCTION IN TURKEY

Directory of Open Access Journals (Sweden)

Osman Gulsen

2017-12-01

Full Text Available Pumpkin seed contains very valuable nutrients and may have some beneficial health effects. The aim of this study was to overview status of pumpkin seed production in Turkey. The production has sharply risen from 11.500 tons in 2015 to 42.181 tons in 2016. The area has also indicated sharp increase from 172.580 da to 628.441 tons in the same period. The first section provides introduction of topics, and later nutrition value of pumpkin seed, taxonomy, production, bottlenecks and breeding efforts are summarized. They have several advantages such as their short vegetation time that just fits the Central Anatolia conditions where vegetation time available is too short for many other crop plants, net profit per de compared to the other crop plants, extended storability, etc.

Policies for second generation biofuels: current status and future challenges

Energy Technology Data Exchange (ETDEWEB)

Egger, Haakan; Greaker, Mads; Potter, Emily

2011-07-01

Current state-of-the-art knowledge concludes that green house gas (GHG) emissions must be controlled and reduced within the next 30-40 years. The transport sector contributes almost a fifth of the current global emissions, and its share is likely to increase in the future. The US and a number of European countries have therefore introduced various support schemes for research and development (RandD) of low emission fuels that can potentially replace the current fossil fuels. One such alternative is biofuels. The advantage of biofuels are that it is easy to introduce into the transport sector. On the other hand, recent research papers question whether the supply of feedstock is sufficient, and to what extent biofuels lead to GHG emission reductions. This report reviews the current status of second generation biofuels. Second generation biofuels are made from cellulose, which according to our survey of the literature, is in more abundant supply than the first generation biofuels feedstocks. Furthermore, it seems to have the potential to reduce GHG emissions from the transport sector without leading to devastating land use changes, which recent critique has held against first generation biofuels. Given that governments have decided to support RandD of low emission fuels, we ask the following questions: Should second generation biofuels receive RandD support to the same extent as other low emission fuels like hydrogen? How should support schemes for second generation biofuels be designed? Second generation biofuels can be divided according to the production process into thermo-chemical and bio-chemical. With respect to the thermo-chemical process the potential for cost reductions seems to be low. On the other hand, ethanol made from cellulose using the biochemical conversion process is far from a ripe technology. Expert reports point to several potential technological breakthroughs which may reduce costs substantially. Hence, cellulosic ethanol, should receive direct

Current status and prospects of research reactors

International Nuclear Information System (INIS)

Gabaraev, A.B.; Cherepnin, Yu.S.; Tretyakov, I.T.; Khmelshikov, V.V.; Dollezhal, N.A.

2009-01-01

Full text: The first nuclear research reactors (RR) appeared in the 1940s. Their initial purpose was to provide knowledge of the main processes associated with neutron-induced nuclear reactions. Later, the rang of problems addressed expanded substantially. Besides fundamental research in the properties of matter, such reactors are successfully used for dealing with problems in the fields of materials science, nuclear engineering, medicine, isotope production, education, etc. Over the whole period of RR fleet growth, more than six hundred nuclear research facilities were built in 70 countries of the world. As of the end of 2008, the number of Russian research reactors in service was about 20% of the globally operating RR fleet. This paper discusses the current status of the world's RR fleet and describes the capabilities of the experimental reactor facilities existing in Russia. In the 21st century, research reactors will remain in demand to solve scientific and technological problems for innovative development of society. The emerging renaissance of nuclear power, the expanding RR uses for production of isotopes and other applications, the increase in the number of countries willing to use nuclear technologies in energy production, industry and science - all contribute to a rebirth of interest in research reactors. One of the ways to improve the experimental capabilities lies in radical upgrading of the reactor facilities with qualitative changes in the main neutronic characteristics of the core. The associated design approaches are illustrated with the example of the IBR-2M reactor at the JNRI in Dubna. The imperative need restricting the spread of nuclear threat leads us to give up using highly enriched uranium in most research reactors. Development of RR fuel with reduced enrichment in uranium has been one of the priority objectives of NIKIET for many years. This paper presents the latest results obtained along these lines, as applied to pool-type research

Current status of radiation transport tools for proliferation and terrorism prevention

International Nuclear Information System (INIS)

Sale, K.E.

2004-01-01

We present the current status and future plans for the set of calculational tools and data bases developed and maintained at LLNL. The calculational tools include the Monte Carlo codes TART and COG as well as the deterministic code ARDRA. In addition to these codes presently in use there is a major development effort for a new massively parallel transport code. An important part of the capability we're developing is a sophisticated user interface, based on a commercial 3-D modeling product, to improve the model development process. A major part of this user interface tool is being developed by Strela under the Nuclear Cities Initiative. Strela has developed a hub-and-spoke technology for code input interconversions (between COG, TART and MCNP) and will produce the plug-ins that extend the capabilities of the 3-D modeler for use as a radiation transport input generator. The major advantages of this approach are the built-in user interface for 3-D modeling and the ability to read a large variety of CAD-file formats. In addition to supporting our current radiation transport codes and developing new capabilities we are working on some nuclear data needs for homeland security. These projects are carried out and the Lawrence Berkeley National Laboratory 88' cyclotron and at the Institute for Nuclear Research of the Nation Academy of Science of Ukraine under and STCU contract. (author)

Radiation processing of agricultural products: status and potential contribution to a cleaner environment

International Nuclear Information System (INIS)

Lapidot, M.

1979-01-01

The current status of radiation processing of agricultural products is briefly reviewed with special regard to those processes which may contribute to a cleaner environment. Radurization of poultry feed and poultry meat is shown to be a major contributor to the reduction of a significant public health problem-salmonellosis. Radiation sterilized animal feeds can be produced by processing garbage - a major environmental pollutant. Radicidation and radappertization are effective processes in the treatment of sludges and waste water, to prevent pollution of seas or ground. Radiation processes can effectively replace fungicides and insecticides in the treatment of agricultural crops and thus reduce environmental pollution. (author)

Biological Production of 3-Hydroxypropionic Acid: An Update on the Current Status

Directory of Open Access Journals (Sweden)

Leonidas Matsakas

2018-02-01

Full Text Available The production of high added-value chemicals from renewable resources is a necessity in our attempts to switch to a more sustainable society. 3-Hydroxypropionic acid (3HP is a promising molecule that can be used for the production of an important array of high added-value chemicals, such as 1,3-propanediol, acrylic acid, acrylamide, and bioplastics. Biological production of 3HP has been studied extensively, mainly from glycerol and glucose, which are both renewable resources. To enable conversion of these carbon sources to 3HP, extensive work has been performed to identify appropriate biochemical pathways and the enzymes that are involved in them. Novel enzymes have also been identified and expressed in host microorganisms to improve the production yields of 3HP. Various process configurations have also been proposed, resulting in improved conversion yields. The intense research efforts have resulted in the production of as much as 83.8 g/L 3HP from renewable carbon resources, and a system whereby 3-hydroxypropionitrile was converted to 3HP through whole-cell catalysis which resulted in 184.7 g/L 3HP. Although there are still challenges and difficulties that need to be addressed, the research results from the past four years have been an important step towards biological production of 3HP at the industrial level.

History, Current Status, and Future Prospects of Counseling in South Korea

Science.gov (United States)

Lee, Sang Min; Suh, Suhyun; Yang, Eunjoo; Jang, Yoo Jin

2012-01-01

Although the counseling profession was introduced to South Korea in the 1950s by American delegates of education, counseling has been only lately recognized as a specialized field that requires distinctive knowledge and skills. In this article, the authors describe the history and the current status of counseling in South Korea and then discuss…

Online-coupled meteorology and chemistry models: history, current status, and outlook

Directory of Open Access Journals (Sweden)

Y. Zhang

2008-06-01

Full Text Available The climate-chemistry-aerosol-cloud-radiation feedbacks are important processes occurring in the atmosphere. Accurately simulating those feedbacks requires fully-coupled meteorology, climate, and chemistry models and presents significant challenges in terms of both scientific understanding and computational demand. This paper reviews the history and current status of the development and application of online-coupled meteorology and chemistry models, with a focus on five representative models developed in the US including GATOR-GCMOM, WRF/Chem, CAM3, MIRAGE, and Caltech unified GCM. These models represent the current status and/or the state-of-the science treatments of online-coupled models worldwide. Their major model features, typical applications, and physical/chemical treatments are compared with a focus on model treatments of aerosol and cloud microphysics and aerosol-cloud interactions. Aerosol feedbacks to planetary boundary layer meteorology and aerosol indirect effects are illustrated with case studies for some of these models. Future research needs for model development, improvement, application, as well as major challenges for online-coupled models are discussed.

CKM Phenomenology and B-mesons physics-present status and current issues

International Nuclear Information System (INIS)

Ali, A.

2004-01-01

We review the status of the Cabibbo-Kobayashi-Maskawa (CKM) matrix elements and the CP-violating phases in the CKM-unitarity triangle. The emphasis in these lecture notes is on B-meson physics, through we also review the current status and issues in the light quark sector of this matrix. Selected applications of theoretical methods in QCD used in the interpretation of data are given and some of the issues restricting the theoretical precision on the CKM matrix elements discussed. The overall consistency of the CKM theory with the available data in flavour physics is impressive and we quantify this consistency. Current data also show some anomalies which, however, are not yet statistically significant. They are discussed briefly. some benchmark measurements that remain to be done in experiments at the B-factories and hadron colliders are listed. Together with the already achieved results, they will provide unprecedented test of the CKM theory and by the same token may lead to the discovery of new physics. (Author) 284 refs

Low-dose antibiotics: current status and outlook for the future

DEFF Research Database (Denmark)

Antimicrobial therapy is a key factor in our success against pathogens poised to ravage at risk or infected individuals. However, we are currently at a watershed point as we face a growing crisis of antibiotic resistance among diverse pathogens. One area of intense interest is the impact of the a......Antimicrobial therapy is a key factor in our success against pathogens poised to ravage at risk or infected individuals. However, we are currently at a watershed point as we face a growing crisis of antibiotic resistance among diverse pathogens. One area of intense interest is the impact...... of the application of antibiotics for uses other than the treatment of patients and the association with such utilization with emerging drug resistance. This Research Topic “Low- dose antibiotics: current status and outlook for the future” in Frontiers in Microbiology: Antimicrobials, Resistance and Chemotherapy...

Current status of Chinese nuclear power industry and technology

International Nuclear Information System (INIS)

Kim, Hyun Min; Kim, Min; Jeong, Hee Jong; Hwang, Jeong Ki; Cho, Chung Hee

1996-10-01

China has been carrying out active international cooperation aiming to be a country where is to be an economical super power and an advanced country in nuclear power technology by the year early 2000, and China also has begun to be recognized as the largest potential market for the construction of nuclear power plants(NPPs) expecting to construct more than thirty nuclear power units by the year 2020. China has advanced technology in the basic nuclear science including liquid metal breeder reactor technology, nuclear material, medium and small size power plants, and isotope production technology, and also China has complete nuclear fuel cycle technology. However, China still has low NPP technology. Therefore, it is expected that China may have complementary cooperative relationship with China, it is expected that Korea may have an access to the advanced Chinese nuclear science technology, and may have a good opportunity to explore the Chinese market actively exporting excellent Korean NPP technology, and further may have a good position to the neighboring Asian countries' NPP markets. From this perspective, general Chinese social status, major nuclear R and D activity status, and correct NPP and technology status have been analyzed in this report, and this report is expected to be a useful resource for cooperating with China in future. 10 tabs., 6 figs., 16 refs. (Author)

Current status of multi-detector row helical CT in imaging of adult ...

African Journals Online (AJOL)

Current status of multi-detector row helical CT in imaging of adult acquired pancreatic diseases and assessing surgical neoplastic resectability. ... The presence of inflammation, masses, and vascular invasion was evaluated and interpreted images were obtained during each phase. Results were compared with surgery, ...

Review of the current status of linear hybrid reactor concepts

International Nuclear Information System (INIS)

Schultz, K.R.

1977-07-01

A review was made of the current status of linear fusion-fission hybrid reactor design studies in the USA. The linear hybrid reactor concepts reviewed include the linear theta-pinch hybrid reactor being studied at Los Alamos Scientific Laboratory, the electron beam-heated solenoid hybrid reactor under development at Physics International Co., the laser-heated solenoid hybrid reactor being investigated at Mathematical Sciences Northwest, Inc., and the linear fusion waste burning reactor being studied at General Atomic Company. The discussion addresses confinement and heating mechanisms for each concept, as well as the hybrid blanket designs. The current state of the four reactor designs is summarized and the performance of the various concepts compared

Income Inequality and Health Status in the United States: Evidence from the Current Population Survey.

Science.gov (United States)

Mellor, Jennifer M.; Milyo, Jeffrey

2002-01-01

Current Population Survey data on self-reported health status and income for the general population and those in poverty were analyzed. No consistent association was found between income inequality and individual health status. Previous findings of such an association were attributed to ecological fallacy or failure to control for individual…

Current status of the Fastbus Micro-Vax

International Nuclear Information System (INIS)

Siskind, E.J.

1985-01-01

The present hardware, firmware, and software design and status of the Fastbus Micro-VAX, a two board Fastbus module packaging of the DEC Micro-VAX II computing system, is described. The hardware currently features an Intel 80186, equipped with 64 kB of ROM, 32 kB of RAM, and an 82586/82501 Ethernet port, as a front end I/O processor, plus a high bandwidth Fastbus interface implemented in semi-custom ECL 100K VLSI with the Motorola MCA2500ECL macrocell array. Standard 80186 firmware implements multiple Fastbus segment drivers and interrupt receivers software compatible with the UPI, a limited Fastbus interprocessor network, and emulations of the DEC DEQNA Ethernet interface and an MSCP disk interface. Software includes device drivers for the non-DEC devices, plus appropriate standard access subroutines for the Fastbus and network devices

Current status of the IREN project

International Nuclear Information System (INIS)

Furman, W.I.

1997-01-01

A current status and a corrected time-schedule of the project of the new Intense Resonance Neutron pulsed source (IREN) realized in JINR (Dubna) for experiments dealing with fundamental and applied nuclear physics studies are discussed. This source is the upgraded variant of the existing IBR-30 pulsed booster. It consists of the 200 MeV electron linac and supplying by an electron beam the photo-neutron converter placed in the center of the very fast multiplying subcritical core. The existing buildings and beam infrastructure are planned to adopt for the new IREN source. The aim of the project is to improve essentially an energy resolution of the time-of-flight spectrometer and to increase twice (up to 10 15 n/sec) an integral neutron yield. An implementation of the IREN project has started in June 1994 with the planned end in December 1997. But due to mainly insufficient financing the approved time-schedule is shifted. Now most optimistic time of start-up of the neutron source is the end of 1999

Current Status of Family Medicine Faculty Development in Sub-Saharan Africa.

Science.gov (United States)

Larson, Paul R; Chege, Patrick; Dahlman, Bruce; Gibson, Christine; Evensen, Ann; Colon-Gonzalez, Maria C; Onguka, Stephanie; Lamptey, Roberta; Cayley, William E; Nguyen, Bich-May; Johnson, Brian; Getnet, Sawra; Hasnain, Memoona

2017-03-01

Reducing the shortage of primary care physicians in sub-Saharan Africa requires expansion of training programs in family medicine. Challenges remain in preparing, recruiting, and retaining faculty qualified to teach in these pioneering programs. Little is known about the unique faculty development needs of family medicine faculty within the sub-Saharan African context. The purpose of this study was to assess the current status and future needs for developing robust family medicine faculty in sub-Saharan Africa. The results are reported in two companion articles. A cross-sectional study design was used to conduct a qualitative needs assessment comprising 37 in-depth, semi-structured interviews of individual faculty trainers from postgraduate family medicine training programs in eight sub-Saharan African countries. Data were analyzed according to qualitative description. While faculty development opportunities in sub-Saharan Africa were identified, current faculty note many barriers to faculty development and limited participation in available programs. Faculty value teaching competency, but institutional structures do not provide adequate support. Sub-Saharan African family physicians and postgraduate trainee physicians value good teachers and recognize that clinical training alone does not provide all of the skills needed by educators. The current status of limited resources of institutions and individuals constrain faculty development efforts. Where faculty development opportunities do exist, they are too infrequent or otherwise inaccessible to provide trainers the necessary skills to help them succeed as educators.

Current Status of HbA1c Biosensors

Science.gov (United States)

Lin, Hua; Yi, Jun

2017-01-01

Glycated hemoglobin (HbA1c) is formed via non-enzymatic glycosylation reactions at the α–amino group of βVal1 residues in the tetrameric Hb, and it can reflect the ambient glycemic level over the past two to three months. A variety of HbA1c detection methods, including chromatography, immunoassay, enzymatic measurement, electrochemical sensor and capillary electrophoresis have been developed and used in research laboratories and in clinics as well. In this review, we summarize the current status of HbA1c biosensors based on the recognition of the sugar moiety on the protein and also their applications in the whole blood sample measurements. PMID:28777351

USDA Foreign Agricultural Service overview for operational monitoring of current crop conditions and production forecasts.

Science.gov (United States)

Crutchfield, J.

2016-12-01

The presentation will discuss the current status of the International Production Assessment Division of the USDA ForeignAgricultural Service for operational monitoring and forecasting of current crop conditions, and anticipated productionchanges to produce monthly, multi-source consensus reports on global crop conditions including the use of Earthobservations (EO) from satellite and in situ sources.United States Department of Agriculture (USDA) Foreign Agricultural Service (FAS) International Production AssessmentDivision (IPAD) deals exclusively with global crop production forecasting and agricultural analysis in support of the USDAWorld Agricultural Outlook Board (WAOB) lockup process and contributions to the World Agricultural Supply DemandEstimates (WASE) report. Analysts are responsible for discrete regions or countries and conduct in-depth long-termresearch into national agricultural statistics, farming systems, climatic, environmental, and economic factors affectingcrop production. IPAD analysts become highly valued cross-commodity specialists over time, and are routinely soughtout for specialized analyses to support governmental studies. IPAD is responsible for grain, oilseed, and cotton analysison a global basis. IPAD is unique in the tools it uses to analyze crop conditions around the world, including customweather analysis software and databases, satellite imagery and value-added image interpretation products. It alsoincorporates all traditional agricultural intelligence resources into its forecasting program, to make the fullest use ofavailable information in its operational commodity forecasts and analysis. International travel and training play animportant role in learning about foreign agricultural production systems and in developing analyst knowledge andcapabilities.

White Paper on Energy Efficiency Status of Energy-Using Products in China (2011)

Energy Technology Data Exchange (ETDEWEB)

Zhou, Nan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Romankiewicz, John [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fridley, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2012-06-01

This White Paper focuses on the areas and products involved in the above tasks, based on the White Paper - Energy Efficiency Status of Energy-Using Products in China (2010), here referred to as “White Paper 2010”, which analyzed the energy efficiency status of 21 typical energy-using products in five sectors: household appliances, office equipment, commercial equipment, industrial equipment, and lighting equipment. Table 1 illustrates the detailed product coverage for this year’s paper, noting the addition of three household appliance items (automatic electric rice cooker, AC electric fan, and household induction cooktop) and one industrial sector item (three-phase distribution transformer).

Hepatitis B Virus Infection in Tanzania: Current Status and Challenges

OpenAIRE

Kilonzo, Semvua B.; Gunda, Daniel W.; Mpondo, Bonaventura C. T.; Bakshi, Fatma A.; Jaka, Hyasinta

2018-01-01

Hepatitis B is one of the most common infectious diseases in the world with high prevalence in most of sub-Saharan Africa countries. The complexity in its diagnosis and treatment poses a significant management challenge in the resource-limited settings including Tanzania, where most of the tests and drugs are either unavailable or unaffordable. This mini review aims at demonstrating the current status of the disease in the country and discussing the concomitant challenges in diagnosis, treatm...

Current status of nuclear power

International Nuclear Information System (INIS)

Behnke, W.B.

1984-01-01

The decision to devote the 1984 conference to nuclear power is timely and appropriate. Illinois has a long, and distinguished history in the development of civilian nuclear power. The concept was born at the University of Chicago, developed at Argonne National Laboratory and demonstrated on the Commonwealth Edison system at our pioneer Dresden Nuclear Station. Today, Illinois ranks number one in the nation in nuclear generation. With over a quarter century of commercial operating experience, nuclear power has proven its worth and become a significant and growing component of electric power supply domestically and throughout the world. Despite its initial acceptance, however, the nuclear power industry in the U.S. is now in the midst of a difficult period of readjustment stemming largely from the economic and regulatory problems of the past decade. As a result, the costs of plants under construction have increased dramatically, causing serious financial difficulties for several projects and their owners. At the same time, the U.S. is facing hard choices concerning its future energy supplies. Conferences such as this have an important role in clarifying the issues and helping to find solutions to today's pressing energy problems. This paper summarizes the status of nuclear power both here and abroad, discussing the implications of current events in the context of national energy policy and economic development here in Illinois

Phytoextraction of Cd-Contaminated Soils: Current Status and Future Challenges

OpenAIRE

Li, Jin-Tian; Baker, Alan J. M.; Ye, Zhi-Hong; Wang, Hong-Bin; Shu, Wen-Sheng

2012-01-01

Cadmium (Cd) is one of the most toxic and widely distributed pollutants in the environment. Cadmium contamination of soils has posed a serious threat to safe food production in many parts of the world. The authors present a comprehensive review of present status of phytoextraction technology for cleaning up Cd-contaminated soils, based primarily on the data resulting from both laboratory and field-scale studies that have been conducted to assess or improve the Cd phytoextraction potential of ...

Digital HCAL Electronics: Status of Production

Energy Technology Data Exchange (ETDEWEB)

Drake, Gary; Repond, Jose, E-mail: drake@hep.anl.gov [Argonne National Laboratory (United States)

2011-04-01

This is a status report of the production of the readout electronics for the Digital Hadron Calorimeter (DHCAL) prototype. The prototype will be equipped with Resistive Plate Chambers (RPCs), read out with 1 x 1 cm{sup 2} pads. The readout of each channel is simplified to provide a yes or no (digital readout) within a time bin of 100 ns. Each detector layer with an area of 96 x 96 cm{sup 2} contains close to 10,000 readout channels. The total channel count for the entire prototype calorimeter with 38 active layers is approximately 350,000.

[Molecular imaging; current status and future prospects in USA].

Science.gov (United States)

Kobayashi, Hisataka

2007-02-01

The goal of this review is to introduce the definition, current status, and future prospects of the molecular imaging, which has recently been a hot topic in medicine and the biological science in USA. In vivo imaging methods to visualize the molecular events and functions in organs or animals/humans are overviewed and discussed especially in combinations of imaging modalities (machines) and contrast agents(chemicals) used in the molecular imaging. Next, the close relationship between the molecular imaging and the nanotechnology, an important part of nanomedicine, is stressed from the aspect of united multidisciplinary sciences such as physics, chemistry, biology, and medicine.

Computer-aided diagnosis in radiological imaging: current status and future challenges

Science.gov (United States)

Doi, Kunio

2009-10-01

Computer-aided diagnosis (CAD) has become one of the major research subjects in medical imaging and diagnostic radiology. Many different types of CAD schemes are being developed for detection and/or characterization of various lesions in medical imaging, including conventional projection radiography, CT, MRI, and ultrasound imaging. Commercial systems for detection of breast lesions on mammograms have been developed and have received FDA approval for clinical use. CAD may be defined as a diagnosis made by a physician who takes into account the computer output as a "second opinion". The purpose of CAD is to improve the quality and productivity of physicians in their interpretation of radiologic images. The quality of their work can be improved in terms of the accuracy and consistency of their radiologic diagnoses. In addition, the productivity of radiologists is expected to be improved by a reduction in the time required for their image readings. The computer output is derived from quantitative analysis of radiologic images by use of various methods and techniques in computer vision, artificial intelligence, and artificial neural networks (ANNs). The computer output may indicate a number of important parameters, for example, the locations of potential lesions such as lung cancer and breast cancer, the likelihood of malignancy of detected lesions, and the likelihood of various diseases based on differential diagnosis in a given image and clinical parameters. In this review article, the basic concept of CAD is first defined, and the current status of CAD research is then described. In addition, the potential of CAD in the future is discussed and predicted.

Interventional Radiology of Male Varicocele: Current Status

International Nuclear Information System (INIS)

Iaccarino, Vittorio; Venetucci, Pietro

2012-01-01

Varicocele is a fairly common condition in male individuals. Although a minor disease, it may cause infertility and testicular pain. Consequently, it has high health and social impact. Here we review the current status of interventional radiology of male varicocele. We describe the radiological anatomy of gonadal veins and the clinical aspects of male varicocele, particularly the physical examination, which includes a new clinical and ultrasound Doppler maneuver. The surgical and radiological treatment options are also described with the focus on retrograde and antegrade sclerotherapy, together with our long experience with these procedures. Last, we compare the outcomes, recurrence and persistence rates, complications, procedure time and cost-effectiveness of each method. It clearly emerges from this analysis that there is a need for randomized multicentre trials designed to compare the various surgical and percutaneous techniques, all of which are aimed at occlusion of the anterior pampiniform plexus.

Current Status of Concentrator Photovoltaic (CPV) Technology

Energy Technology Data Exchange (ETDEWEB)

Philipps, Simon P. [Fraunhofer Inst. for Solar Energy Systems ISE, Freiburg (Germany); Bett, Andreas W. [Fraunhofer Inst. for Solar Energy Systems ISE, Freiburg (Germany); Horowitz, Kelsey [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kurtz, Sarah [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2015-12-01

This report summarizes the status of the concentrator photovoltaic (CPV) market and industry as well as current trends in research and technology. This report is intended to guide research agendas for Fraunhofer ISE, the National Renewable Energy Laboratory (NREL), and other R&D organizations. Version 1.1 of this report includes recent progress in CPV. The recent record module efficiency of 38.9% at Concentrator Standard Test Conditions (CSTC) is an impressive result, demonstrating the continuing opportunity for CPV technology to improve. 38.9% at Concentrator Standard Test Conditions (CSTC) is an impressive result, demonstrating the continuing opportunity for CPV technology to improve. 38.9% at Concentrator Standard Test Conditions (CSTC) is an impressive result, demonstrating the continuing opportunity for CPV technology to improve. 38.9% at Concentrator Standard Test Conditions (CSTC) is an impressive result, demonstrating the continuing opportunity for CPV technology to improve.

Interventional Radiology of Male Varicocele: Current Status

Energy Technology Data Exchange (ETDEWEB)

Iaccarino, Vittorio, E-mail: vittorio.iaccarino@unina.it; Venetucci, Pietro [University of Naples ' Federico II' , Diagnostic Imaging Department-Cardiovascular and Interventional Radiology, School of Medicine (Italy)

2012-12-15

Varicocele is a fairly common condition in male individuals. Although a minor disease, it may cause infertility and testicular pain. Consequently, it has high health and social impact. Here we review the current status of interventional radiology of male varicocele. We describe the radiological anatomy of gonadal veins and the clinical aspects of male varicocele, particularly the physical examination, which includes a new clinical and ultrasound Doppler maneuver. The surgical and radiological treatment options are also described with the focus on retrograde and antegrade sclerotherapy, together with our long experience with these procedures. Last, we compare the outcomes, recurrence and persistence rates, complications, procedure time and cost-effectiveness of each method. It clearly emerges from this analysis that there is a need for randomized multicentre trials designed to compare the various surgical and percutaneous techniques, all of which are aimed at occlusion of the anterior pampiniform plexus.

Wind energy status in renewable electrical energy production in Turkey

International Nuclear Information System (INIS)

Kaygusuz, Kamil

2010-01-01

Main electrical energy sources of Turkey are thermal and hydraulic. Most of the thermal sources are derived from natural gas. Turkey imports natural gas; therefore, decreasing usage of natural gas is very important for both economical and environmental aspects. Because of disadvantages of fossil fuels, renewable energy sources are getting importance for sustainable energy development and environmental protection. Among the renewable sources, Turkey has very high wind energy potential. The estimated wind power capacity of Turkey is about 83,000 MW while only 10,000 MW of it seems to be economically feasible to use. Start 2009, the total installed wind power capacity of Turkey was only 4.3% of its total economical wind power potential (433 MW). However, the strong development of wind energy in Turkey is expected to continue in the coming years. In this study, Turkey's installed electric power capacity, electric energy production is investigated and also Turkey current wind energy status is examined. (author)

Robotic technology in surgery: current status in 2008.

Science.gov (United States)

Murphy, Declan G; Hall, Rohan; Tong, Raymond; Goel, Rajiv; Costello, Anthony J

2008-12-01

There is increasing patient and surgeon interest in robotic-assisted surgery, particularly with the proliferation of da Vinci surgical systems (Intuitive Surgical, Sunnyvale, CA, USA) throughout the world. There is much debate over the usefulness and cost-effectiveness of these systems. The currently available robotic surgical technology is described. Published data relating to the da Vinci system are reviewed and the current status of surgical robotics within Australia and New Zealand is assessed. The first da Vinci system in Australia and New Zealand was installed in 2003. Four systems had been installed by 2006 and seven systems are currently in use. Most of these are based in private hospitals. Technical advantages of this system include 3-D vision, enhanced dexterity and improved ergonomics when compared with standard laparoscopic surgery. Most procedures currently carried out are urological, with cardiac, gynaecological and general surgeons also using this system. The number of patients undergoing robotic-assisted surgery in Australia and New Zealand has increased fivefold in the past 4 years. The most common procedure carried out is robotic-assisted laparoscopic radical prostatectomy. Published data suggest that robotic-assisted surgery is feasible and safe although the installation and recurring costs remain high. There is increasing acceptance of robotic-assisted surgery, especially for urological procedures. The da Vinci surgical system is becoming more widely available in Australia and New Zealand. Other surgical specialties will probably use this technology. Significant costs are associated with robotic technology and it is not yet widely available to public patients.

The current status of radioactive monitoring gauges in UIC

International Nuclear Information System (INIS)

Ji Changsong

1993-01-01

The author introduces the characteristics of representative products for current environment radiation monitoring and measurement instruments of radiation nuclide content in UIC including aerosol detection equipment and multi function radiation dosemeters

Current Status and Application of Hazard Definition Technology

Science.gov (United States)

Greene, George C.

1997-01-01

A research is performed: to define wake non-encounter & hazard, to provide requirements for sensors, and to obtain input from the user community. This research includes: validating wake encounter simulation models, establishing a metric to quantify the upset potential of a wake encounter, applying hazard metric and simulation models to the commercial fleet for development of candidate acceptable encounter limits, and applying technology to near term problems to evaluate current status of technology. The following lessons are learned from this project: technology is not adequate to determine absolute spacing requirements; time, not distance, determines the duration of the wake hazard; Optimum standards depend on the traffic; Wing span is an important parameter for characterizing both generator and follower; and Short span "biz jets" are easily rolled.

Hepatitis B Virus Infection in Tanzania: Current Status and Challenges

Science.gov (United States)

Bakshi, Fatma A.; Jaka, Hyasinta

2018-01-01

Hepatitis B is one of the most common infectious diseases in the world with high prevalence in most of sub-Saharan Africa countries. The complexity in its diagnosis and treatment poses a significant management challenge in the resource-limited settings including Tanzania, where most of the tests and drugs are either unavailable or unaffordable. This mini review aims at demonstrating the current status of the disease in the country and discussing the concomitant challenges in diagnosis, treatment, and prevention. PMID:29666656

Hepatitis B Virus Infection in Tanzania: Current Status and Challenges

Directory of Open Access Journals (Sweden)

Semvua B. Kilonzo

2018-01-01

Full Text Available Hepatitis B is one of the most common infectious diseases in the world with high prevalence in most of sub-Saharan Africa countries. The complexity in its diagnosis and treatment poses a significant management challenge in the resource-limited settings including Tanzania, where most of the tests and drugs are either unavailable or unaffordable. This mini review aims at demonstrating the current status of the disease in the country and discussing the concomitant challenges in diagnosis, treatment, and prevention.

Civilian Power Program. Part 1, Summary, Current status of reactor concepts

Energy Technology Data Exchange (ETDEWEB)

Author, Not Given

1959-09-01

This study group covered the following: delineation of the specific objectives of the overall US AEC civilian power reactor program, technical objectives of each reactor concept, preparation of a chronological development program for each reactor concept, evaluation of the economic potential of each reactor type, a program to encourage the the development, and yardsticks for measuring the development. Results were used for policy review by AEC, program direction, authorization and appropriation requests, etc. This evaluation encompassed civilian power reactors rated at 25 MW(e) or larger and related experimental facilities and R&D. This Part I summarizes the significant results of the comprehensive effort to determine the current technical and economic status for each reactor concept; it is based on the 8 individual technical status reports (Part III).

Current status of ITER EC design

International Nuclear Information System (INIS)

Bosia, G.

2003-01-01

The ITER-FEAT Electron Cyclotron System employs one equatorial launcher and three upper port launchers to inject 20 + 20 MW of mm-wave power at 170 GHz through slots in the plasma-facing neutron and radiation shield. The equatorial launcher includes 3 sets of toroidally steer-able mirrors, each collecting 8 RF beams from 24 circular cross-section corrugated wave-guides. In the upper-port launcher, eight beams, reflected in pairs by four toroidally angled (∼30 angle) and poloidally steer-able (∼ 10 angle) mirrors focus of the RF power on the plasma m = 2 and m = 3/2 plasma flux rational surfaces, for neo-classical tearing mode(s) (NTM) control. Conceptual studies of remote steering that would possibly allow removing the beam- steering equipment from the vacuum vessel and locating them in more protected positions have been carried out. All EC wave transmission is based on low losses circular cross section corrugated and evacuated wave guides each connected to a 170 GHz, 1 MW CW Gyrotron tube oscillator featuring an overall efficiency of ∼ 50%, obtained by depressed-collector energy recovery. In the paper, requirements, issues and the current status of the design is reviewed. (authors)

The Current Status and Prospects for Development of International Trade in Goods

Directory of Open Access Journals (Sweden)

Kovtun Tamara D.

2018-03-01

Full Text Available The article is aimed at analyzing the current status and determining prospects for international trade in goods. The dynamics of international trade in goods are characterized and the reasons for its slowdown are disclosed. A considerable attention is paid to the analysis of the commodity and geographical structure of the international trade in goods. On the basis of the conducted research the new tendencies and peculiarities of development of the international trade in goods in the contemporary conditions are disclosed. In particular, the authors consider the tendency of increasing the influence of non-tariff barriers on the dynamics of the international commodity exchange. Based on the calculation of the export quota as an indicator of the intensity of foreign trade in goods, conclusions have been drawn about the degree of openness of national economies in the current conditions. The authors have noted that in the coming years the growth of physical and value volumes of the world commodity exports is projected in the conditions of growth of the world prices for raw products. It has been determined that, most likely, further development of the international trade in goods will take place in conditions of deepening of trade integration at the mega-regional level. An increase in the number of participants in the international trade in goods is also expected in the context of further spread of e-commerce in the developing countries.

Status of decay data of fission products

International Nuclear Information System (INIS)

Blachot, J.

1978-01-01

Fission products (F.P.) are neutron rich isotopes ranging from Zn to Tm. The status of decay data of F.P. was described at the Bologna Panel 1973 by Rudstam. Since then, FPND have improved in general, but still much is valid of what Rudstam said about the accuracies of FPND. The lack of decay data for the short lived F.P. has been considerably reduced, and some of the short lived F.P. have now well studied decay data. The present status of decay data is given in this review, which is composed of six sections. In the first one, the principal new facilities used in decay data measurements are reviewed. The second part is devoted to the total decay energy (Q). In the third Section, the half lives are treated. In the fourth and fifth Sections, beta and gamma energies and intensities, and also average values are discussed. Finally, the last Section considers the different files and compilations devoted to the decay of F.P

Tele-yoga for Chronic Pain: Current Status and Future Directions.

Science.gov (United States)

Mathersul, Danielle C; Mahoney, Louise A; Bayley, Peter J

2018-01-01

Pain is a pervasive, debilitating disorder that is resistant to long-term pharmacological interventions. Although psychological therapies such as cognitive behavior therapy demonstrate moderate efficacy, many individuals continue to have ongoing difficulties following treatment. There is a current trend to establish complementary and integrative health interventions for chronic pain, for which yoga has been found to have exciting potential. Nevertheless, an important consideration within the field is accessibility to adequate care. Telehealth can be used to provide real-time interactive video conferencing leading to increased access to health care for individuals located remotely or who otherwise have difficulty accessing services, perhaps through issues of mobility or proximity of adequate services. This article assesses the current status and feasibility of implementing tele-yoga for chronic pain. Methodological limitations and recommendations for future research are discussed.

Current status and policies on biodiesel industry in Malaysia as the world's leading producer of palm oil

International Nuclear Information System (INIS)

Abdullah, A.Z.; Salamatinia, B.; Mootabadi, H.; Bhatia, S.

2009-01-01

This article discusses current status of palm oil-based biodiesel industry in Malaysia, the policies introduced and strategies for its implementation. Due to renewability, high production rate, technical feasibility and role in reducing greenhouse gases (GHG) emission, palm oil is in the right position to supply the energy needs by the incorporation into the diesel supply. As a leading producer of palm oil, Malaysia has embarked on a comprehensive palm biofuel program since 1982. It has successfully established the use of palm biodiesel blend (B5) as a suitable fuel for the transport and industrial sectors through the introduction of the National Biofuel Policy. The current scenario of biodiesel program in Malaysia, as well as biofuel policies with respect to its use, technology, export, environmental issues and implementation aspects are thoroughly discussed. The roles of the policy towards the prosperity of the stakeholders, oil price and the reduction of greenhouse gasses are also highlighted. (author)

The Japanese artificial organs scene: current status.

Science.gov (United States)

Mitamura, Yoshinori; Murabayashi, Shun

2005-08-01

Artificial organs and regenerative medicine are the subjects of very active research and development (R&D) in Japan and various artificial organs are widely used in patients. Results of the R&D are presented at the annual conference of the Japanese Society for Artificial Organs (JSAO). Progress in the fields of artificial organs and regenerative medicine are reviewed annually in the Japanese Journal of Artificial Organs. The official English-language journal of JSAO, Journal of Artificial Organs, also publishes many original articles by Japanese researchers. Although the annual conference and the publications of JSAO provide the world with update information on artificial organs and regenerative medicine in Japan, the information is not always understood appropriately in the rest of the world, mainly due to language problems. This article therefore introduces the current status of artificial organs and regenerative medicine in Japan. Artificial hearts and metabolic support systems are reviewed here and other interesting areas such as regenerative medicine can be found elsewhere.

Current status of the FASTGRASS/PARAGRASS models for fission product release from LWR fuel during normal and accident conditions

International Nuclear Information System (INIS)

Rest, J.; Zawadski, S.A.; Piasecka, M.

1983-10-01

The theoretical FASTGRASS model for the prediction of the behavior of the gaseous and volatile fission products in nuclear fuels under normal and transient conditions has undergone substantial improvements. The major improvements have been in the atomistic and bubble diffusive flow models, in the models for the behavior of gas bubbles on grain surfaces, and in the models for the behavior of the volatile fission products iodine and cesium. The thoery has received extensive verification over a wide range of fuel operating conditions, and can be regarded as a state-of-the-art model based on our current level of understanding of fission product behavior. PARAGRASS is an extremely efficient, mechanistic computer code with the capability of modeling steady-state and transient fission-product behavior. The models in PARAGRASS are based on the more detailed ones in FASTGRASS. PARAGRASS updates for the FRAPCON (PNL), FRAP-T (INEL), and SCDAP (INEL) codes have recently been completed and implemented. Results from an extensive FASTGRASS verification are presented and discussed for steady-state and transient conditions. In addition, FASTGRASS predictions for fission product release rate constants are compared with those in NUREG-0772. 21 references, 13 figures

Current status in biotechnological production and applications of glycolipid biosurfactants.

Science.gov (United States)

Paulino, Bruno Nicolau; Pessôa, Marina Gabriel; Mano, Mario Cezar Rodrigues; Molina, Gustavo; Neri-Numa, Iramaia Angélica; Pastore, Glaucia Maria

2016-12-01

Biosurfactants are natural compounds with surface activity and emulsifying properties produced by several types of microorganisms and have been considered an interesting alternative to synthetic surfactants. Glycolipids are promising biosurfactants, due to low toxicity, biodegradability, and chemical stability in different conditions and also because they have many biological activities, allowing wide applications in different fields. In this review, we addressed general information about families of glycolipids, rhamnolipids, sophorolipids, mannosylerythritol lipids, and trehalose lipids, describing their chemical and surface characteristics, recent studies using alternative substrates, and new strategies to improve of production, beyond their specificities. We focus in providing recent developments and trends in biotechnological process and medical and industrial applications.

Current status of large-scale cryogenic gravitational wave telescope

International Nuclear Information System (INIS)

Kuroda, K; Ohashi, M; Miyoki, S; Uchiyama, T; Ishitsuka, H; Yamamoto, K; Kasahara, K; Fujimoto, M-K; Kawamura, S; Takahashi, R; Yamazaki, T; Arai, K; Tatsumi, D; Ueda, A; Fukushima, M; Sato, S; Nagano, S; Tsunesada, Y; Zhu, Zong-Hong; Shintomi, T; Yamamoto, A; Suzuki, T; Saito, Y; Haruyama, T; Sato, N; Higashi, Y; Tomaru, T; Tsubono, K; Ando, M; Takamori, A; Numata, K; Aso, Y; Ueda, K-I; Yoneda, H; Nakagawa, K; Musha, M; Mio, N; Moriwaki, S; Somiya, K; Araya, A; Kanda, N; Telada, S; Tagoshi, H; Nakamura, T; Sasaki, M; Tanaka, T; Oohara, K; Takahashi, H; Miyakawa, O; Tobar, M E

2003-01-01

The large-scale cryogenic gravitational wave telescope (LCGT) project is the proposed advancement of TAMA, which will be able to detect the coalescences of binary neutron stars occurring in our galaxy. LCGT intends to detect the coalescence events within about 240 Mpc, the rate of which is expected to be from 0.1 to several events in a year. LCGT has Fabry-Perot cavities of 3 km baseline and the mirrors are cooled down to a cryogenic temperature of 20 K. It is planned to be built in the underground of Kamioka mine. This paper overviews the revision of the design and the current status of the R and D

CT myocardial perfusion imaging: current status and future perspectives.

Science.gov (United States)

Yang, Dong Hyun; Kim, Young-Hak

2017-07-01

Computed tomography myocardial perfusion (CTP) combined with coronary computed tomography angiography (CCTA) may constitute a "1-stop shop" for the noninvasive diagnosis of hemodynamically significant coronary stenosis during a single CT examination. CTP shows high diagnostic performance and provides incremental value over CCTA for the detection of hemodynamically significant coronary stenosis in patients with a high Agatston calcium score or coronary artery stents. Future studies should determine the optimal protocol and clinical value of CTP for guiding revascularization strategy and prognostication. In this article, we review the current status and future perspectives of CTP, focusing on technical considerations, clinical applications, and future research topics.

History and current status of nuclear fuel reprocessing technology

International Nuclear Information System (INIS)

Funasaka, Hideyuki; Nagai, Toshihisa; Washiya, Tadahiro

2008-01-01

History and present state of fast breeder reactor was reviewed in series. As a history and current status of nuclear fuel reprocessing technology, this ninth lecture presented the progress of the FBR fuel reprocessing technology and advanced reprocessing processes. FBR fuel reprocessing technology had been developed to construct the reprocessing equipment test facilities (RETF) based on PUREX process technologies. With economics, reduction of environmental burdens and proliferation resistance taken into consideration, advanced aqueous method for nuclear fuel cycle activities has been promoted as the government's basic policy. Innovative technologies on mechanical disassembly, continuous rotary dissolver, crystallizer, solvent extraction and actinides recovery have been mainly studied. (T. Tanaka)

Community-based dental education: history, current status, and future.

Science.gov (United States)

Formicola, Allan J; Bailit, Howard L

2012-01-01

This article examines the history, current status, and future direction of community-based dental education (CBDE). The key issues addressed include the reasons that dentistry developed a different clinical education model than the other health professions; how government programs, private medical foundations, and early adopter schools influenced the development of CBDE; the societal and financial factors that are leading more schools to increase the time that senior dental students spend in community programs; the impact of CBDE on school finances and faculty and student perceptions; and the reasons that CBDE is likely to become a core part of the clinical education of all dental graduates.

Mathematical model for production of an industry focusing on worker status

Science.gov (United States)

Visalakshi, V.; kiran kumari, Sheshma

2018-04-01

Productivity improvement is posing a great challenge for industry everyday because of the difficulties in keeping track and priorising the variables that have significant impact on the productivity. The variation in production depends on the linguistic variables such as worker commitment, worker motivation and worker skills. Since the variables are linguistic we try to propose a model which gives an appropriate production of an industry. Fuzzy models aids the relationship between the factors and status. The model will support the industry to focus on the mentality of worker to increase the production.

MELiSSA Food Characterization general approach and current status

Science.gov (United States)

Weihreter, Martin; Chaerle, Laury; Secco, Benjamin; Molders, Katrien; van der Straeten, Dominique; Duliere, Eric; Pieters, Serge; Maclean, Heather; Dochain, Denis; Quinet, Muriel; Lutts, Stanley; Graham, Thomas; Stasiak, Michael; Rondeau Vuk, Theresa; Zheng, Youbin; Dixon, Mike; Laniau, Martine; Larreture, Alain; Timsit, Michel; Aronne, Giovanna; Barbieri, Giancarlo; Buonomo, Roberta; Veronica; Paradiso, Roberta; de Pascale, Stafania; Galbiati, Massimo; Troia, A. R.; Nobili, Matteo; Bucchieri, Lorenzo; Page, Valérie; Feller, Urs; Lasseur, Christophe

. Available MELiSSA closed environment crop growth data were used to develop a first photosynthetic model representing the basic carbon fixation mechanisms. This model will be further elaborated in the course of this study to predict yield, oxygen production and transpi-ration. As an ultimate goal the model is intended to simulate the composition of the different plant organs (root, shoot, fruit/seed or tuber) for each crop under various conditions. For the validation of this model an extensive amount of data sets are needed. Current plant growth bench test setups will provide part of the required data. To gain more precise and detailed datasets, a highly closed plant growth chamber (Plant Characterization Unit, PCU) is under development. The PCU will provide accurate mass balances for carbon, water, oxygen and other elements with statistical reliability. This reliability is achieved through a high degree of closure and environment homogeneity. The PCU will also provide data for the above described plant characterization studies. The general work approach, the current status and future steps will be illustrated.

Early Childhood Inclusion in the United States: Goals, Current Status, and Future Directions

Science.gov (United States)

Guralnick, Michael J.; Bruder, Mary Beth

2016-01-01

The current status and future directions of early childhood inclusion in the United States are discussed from the perspective of 4 key goals: access, accommodations and feasibility, developmental progress, and social integration. Recommendations are put forward to promote inclusion goals emphasizing administrative structures, personnel…

Terrestrial gamma ray flash production by lightning current pulses

OpenAIRE

İnan, Umran Savaş; Carlson, B. E.; Lehtinen, N. G.

2017-01-01

Terrestrial gamma ray flashes (TGFs) are brief bursts of gamma rays observed by satellites, typically in coincidence with detectable lightning. We incorporate TGF observations and the key physics behind current TGF production theories with lightning physics to produce constraints on TGF production mechanisms. The combined constraints naturally suggest a mechanism for TGF production by current pulses in lightning leader channels. The mechanism involves local field enhancements due to charge re...

[Current approaches to evaluating the anatomic and functional status of the cornea].

Science.gov (United States)

Avetisov, S E; Borodina, N V; Kobzova, M V; Musaeva, G M

2010-01-01

The review provides data on current methods for evaluating the anatomic and functional status of the cornea (light refraction, light transmission, and biomechanical properties, in particular). It analyzes the main advantages and disadvantages of basic (biomicroscopy, endothelial microscopy, ophthalmometry, topography, and pachymetry) and special (confocal microscopy, optical coherence tomography, ultrasound biomicroscopy, aberrometry, bidirectional corneal applanation, and keratoesthesiometry) studies.

The Longitudinal Effect of Drug Use on Productivity Status of Nonmetropolitan African American Young Adults

Science.gov (United States)

Roldós, María Isabel

2014-01-01

The purpose of this study was to investigate the longitudinal effect of marijuana and heavy alcohol use on the productivity status of nonmetropolitan African American young adults. This analysis was based on secondary data from the Family and Community Health Study. For alcohol, the study evaluated the effects on productivity status for…

[Current status of bio-based materials industry in China].

Science.gov (United States)

Diao, Xiaoqian; Weng, Yunxuan; Huang, Zhigang; Yang, Nan; Wang, Xiyuan; Zhang, Min; Jin, Yujuan

2016-06-25

In recent years, bio-based materials are becoming a new dominant industry leading the scientific and technological innovation, and economic development of the world. We reviewed the new development of bio-based materials industry in China, analyzed the entire market of bio-based materials products comprehensively, and also stated the industry status of bio-based chemicals, such as lactic acid, 1,3-propanediol, and succinic acid; biodegradable bio-based polymers, such as co-polyester of diacid and diol, polylactic acid, carbon dioxide based copolymer, polyhydroxyalknoates, polycaprolactone, and thermoplastic bio-based plastics; non-biodegradable bio-based polymers, such as bio-based polyamide, polytrimethylene terephthalate, bio-based polyurethane, and bio-based fibers.

Genetic engineering and sustainable production of ornamentals: current status and future directions.

Science.gov (United States)

Lütken, Henrik; Clarke, Jihong Liu; Müller, Renate

2012-07-01

Through the last decades, environmentally and health-friendly production methods and conscientious use of resources have become crucial for reaching the goal of a more sustainable plant production. Protection of the environment requires careful consumption of limited resources and reduction of chemicals applied during production of ornamental plants. Numerous chemicals used in modern plant production have negative impacts on human health and are hazardous to the environment. In Europe, several compounds have lost their approval and further legal restrictions can be expected. This review presents the more recent progress of genetic engineering in ornamental breeding, delivers an overview of the biological background of the used technologies and critically evaluates the usefulness of the strategies to obtain improved ornamental plants. First, genetic engineering is addressed as alternative to growth retardants, comprising recombinant DNA approaches targeting relevant hormone pathways, e.g. the gibberellic acid (GA) pathway. A reduced content of active GAs causes compact growth and can be facilitated by either decreased anabolism, increased catabolism or altered perception. Moreover, compactness can be accomplished by using a natural transformation approach without recombinant DNA technology. Secondly, metabolic engineering approaches targeting elements of the ethylene signal transduction pathway are summarized as a possible alternative to avoid the use of chemical ethylene inhibitors. In conclusion, molecular breeding approaches are dealt with in a way allowing a critical biological assessment and enabling the scientific community and public to put genetic engineering of ornamental plants into a perspective regarding their usefulness in plant breeding.

Improvement of industrially important microbial strains by genome shuffling: Current status and future prospects.

Science.gov (United States)

Magocha, Tinashe Archbold; Zabed, H; Yang, Miaomiao; Yun, Junhua; Zhang, Huanhuan; Qi, Xianghui

2018-06-01

The growing demand for biotechnological products against limited metabolic capacity of industrially used microorganisms has led to an increased interest on strain-improvement over the last several decades, which aimed to enhance metabolite yield, substrate uptake and tolerance of the strains. Among a few techniques of strain-improvement, genome shuffling is the most recent and promising approach used for rapid strain-improvement that can yield a new strain by combining whole genomes of multi-parental microorganisms using the principles of protoplast fusion. Genome shuffling has brought a major breakthrough in the strain-improvement concept as it is found to be effective and reliable for expressing complex phenotypes. This review will discuss the technical aspects and applications of genome shuffling for various industrial strains to present its current status and recent progress. In the concluding remarks, a summary will be presented focusing on the major challenges and future outlooks of this technology. Copyright © 2018 Elsevier Ltd. All rights reserved.

Current Status and Future Potential of Energy Derived from Chinese Agricultural Land: A Review

Directory of Open Access Journals (Sweden)

Ningning Zhai

2015-01-01

Full Text Available Energy crisis is receiving attention with regard to the global economy and environmental sustainable development. Developing new energy resources to optimize the energy supply structure has become an important measure to prevent energy shortage as well as achieving energy conservation and emission reduction in China. This study proposed the concept of energy agriculture and constructed an energy agricultural technical support system based on the analysis of energy supply and demand and China’s foreign dependence on energy resources, combined with the function of agriculture in the energy field. Manufacturing technology equipment and agricultural and forestry energy, including crop or forestry plants and animal feces, were used in the system. The current status and future potential of China’s marginal land resources, energy crop germplasm resources, and agricultural and forestry waste energy-oriented resources were analyzed. Developing the function of traditional agriculture in food production may promote China’s social, economic, and environmental sustainable development and achieve energy saving and emission reduction.

Fuel Cell Buses in U.S. Transit Fleets: Current Status 2011

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.; Gikakis, C.

2011-11-01

This status report, fifth in a series of annual status reports from the U.S. Department of Energy's National Renewable Energy Laboratory (NREL), discusses the achievements and challenges of fuel cell propulsion for transit and summarizes the introduction of fuel cell transit buses in the United States. Progress this year includes an increase in the number of fuel cell electric buses (FCEBs), from 15 to 25, operating at eight transit agencies, as well as increased diversity of the fuel cell design options for transit buses. The report also provides an analysis of the combined results from fuel cell transit bus demonstrations evaluated by NREL with a focus on the most recent data through July 2011 including fuel cell power system reliability and durability; fuel economy; roadcall; and hydrogen fueling results. These evaluations cover 22 of the 25 FCEBs currently operating.

Current status on techniques for determining paleo-temperature using geothermometer

International Nuclear Information System (INIS)

Kanazawa, Sunao; Oikawa, Teruki; Umeda, Koji; Tomiyama, Shingo

2005-01-01

Development of the research technologies for geotectonic events has been carried out to evaluate the long-term stability of geological environment. In terms of the effects of geothermal activity, it is necessary to estimate the geothermal regime and thermal history on any given site. This paper describes the current status on techniques for determining paleo-temperature using geothermometer, and presents a concept of the systematic research techniques. The application of geothermometer, especially thermochronology, has been effective in the studies on the cooling history of geological body and the paleo-geothermal structure at depth. (author)

The current status of prophylactic replacement therapy in children and adults with haemophilia.

Science.gov (United States)

Ljung, Rolf; Gretenkort Andersson, Nadine

2015-06-01

Initiating prophylactic treatment at an early age is considered to be the optimal form of therapy for a child with haemophilia A or B. The pioneering long term experiences of prophylactic treatment from Sweden and The Netherlands demonstrated the benefit of prophylaxis in retrospective and observational studies. Decades later, these benefits were confirmed in a randomized controlled study in USA. We review the current status of prophylactic replacement therapy of haemophilia in children, adolescents, adults and the elderly. Prophylaxis should begin at an early age and there are arguments for continuing it into adulthood. The dose of prophylaxis is dependent on the goal of treatment, economic resources and venous access and should be tailored individually. Starting the first exposures to clotting factor concentrates as prophylactic treatment, instead of on-demand in response to a bleed, may decrease the frequency of inhibitors in patients with haemophilia A. Novel longer-acting products are being introduced that could be helpful for patients with difficult venous access and enable higher trough levels. © 2015 John Wiley & Sons Ltd.

Current algebra and soft pion theorems for weak π production

International Nuclear Information System (INIS)

Adler, S.L.

1976-01-01

Beginning with definitions of vector, scalar, axial vector, pseudoscalar, and tensor current densities, equal time current commutators are derived and divergences are discussed. The partially conserved axial current (PCAC) hypothesis is formulated and used to derive the Goldberger--Treiman relation. Current algebra and the PCAC hypothesis are then employed to develop a master formula describing the reaction J + N → π + N where J is a current with four momentum k, and π is a soft pion with four momentum q. Several applications are considered: πN scattering consistency conditions, π isovector electroproduction relations, π production by an isoscalar weak neutral current, π axial vector weak production relations, and low energy theorems which combine soft pion results with knowledge of divergences of the vector or axial vector current J (which induces weak pion production). It is concluded that (1) the entire weak production amplitude is determined to zero order in q by soft pion theorems, and (2) combined relations determine corrections linear in q but of zero order in k

WISM - A Wideband Instrument for Snow Measurement: Past Accomplishments, Current Status, and Path Forward

Science.gov (United States)

Bonds, Quenton; Racette, Paul; Durham, Tim (Principal Investigator)

2016-01-01

Presented are the prior accomplishments, current status and path forward for GSFC's Wideband Instrument for Snow Measurement (WISM). This work is a high level overview of the project, presented via Webinar to the IEEE young professionals.

Psychological Therapies for Auditory Hallucinations (Voices): Current Status and Key Directions for Future Research

NARCIS (Netherlands)

Thomas, N.; Hayward, M.; Peters, E; van der Gaag, M.; Bentall, R.P.; Jenner, J.; Strauss, C.; Sommer, I.E.; Johns, L.C.; Varese, F.; Gracia-Montes, J.M.; Waters, F.; Dodgson, G.; McCarthy-Jones, S.

2014-01-01

This report from the International Consortium on Hallucinations Research considers the current status and future directions in research on psychological therapies targeting auditory hallucinations (hearing voices). Therapy approaches have evolved from behavioral and coping-focused interventions,

Present status of research on hydrogen energy and perspective of HTGR hydrogen production system

Energy Technology Data Exchange (ETDEWEB)

Miyamoto, Yoshiaki; Ogawa, Masuro; Akino, Norio [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment] [and others

2001-03-01

A study was performed to make a clear positioning of research and development on hydrogen production systems with a High Temperature Gas-cooled Reactor (HTGR) under currently promoting at the Japan Atomic Energy Research Institute through a grasp of the present status of hydrogen energy, focussing on its production and utilization as an energy in future. The study made clear that introduction of safe distance concept for hydrogen fire and explosion was practicable for a HTGR hydrogen production system, including hydrogen properties and need to provide regulations applying to handle hydrogen. And also generalization of hydrogen production processes showed technical issues of the HTGR system. Hydrogen with HTGR was competitive to one with fossil fired system due to evaluation of production cost. Hydrogen is expected to be used as promising fuel of fuel cell cars in future. In addition, the study indicated that there were a large amount of energy demand alternative to high efficiency power generation and fossil fuel with nuclear energy through the structure of energy demand and supply in Japan. Assuming that hydrogen with HTGR meets all demand of fuel cell cars, an estimation would show introduction of the maximum number of about 30 HTGRs with capacity of 100 MWt from 2020 to 2030. (author)

Standards development status. Summary report

International Nuclear Information System (INIS)

1981-12-01

The Standards Development Status Summary Report is designed for scheduling, monitoring, and controlling the process by which Regulatory Standards, Guides, Reports, Petitions, and Environmental Statements are written. It is a summary of the current schedule plans for development of the above products

Nuclear power for sustainable development. Current status and future prospects

International Nuclear Information System (INIS)

Adamantiades, A.; Kessides, I.

2009-01-01

Interest in nuclear power has been revived as a result of volatile fossil fuel prices, concerns about the security of energy supplies, and global climate change. This paper describes the current status and future plans for expansion of nuclear power, the advances in nuclear reactor technology, and their impacts on the associated risks and performance of nuclear power. Advanced nuclear reactors have been designed to be simpler and safer, and to have lower costs than currently operating reactors. By addressing many of the public health and safety risks that plagued the industry since the accidents at Three Mile Island and Chernobyl, these reactors may help break the current deadlock over nuclear power. In that case, nuclear power could make a significant contribution towards reducing greenhouse gas emissions. However, significant issues persist, fueling reservations among the public and many decision makers. Nuclear safety, disposal of radioactive wastes, and proliferation of nuclear explosives need to be addressed in an effective and credible way if the necessary public support is to be obtained. (author)

Current Status and Future Agenda for the Theory, Research, and Practice of Childhood Career Development

Science.gov (United States)

Schultheiss, Donna E. Palladino

2008-01-01

This article reviews the current status and a future agenda for childhood career development theory, research, and practice. The fragmented nature of the current state of the literature is noted, and a call is made for a reexamination and reconsideration of the childhood developmental pathways of life's work. It is suggested that the study of…

The ICA Communication Audit: Process, Status, Critique

Science.gov (United States)

Goldhaber, Gerald M.; Krivonos, Paul D.

1977-01-01

Explores the International Communication Association (ICA) Audit process including goals, products, instruments, audit logistics and timetable, feedback of results and follow-up, costs, current status and audits conducted to date. (ED.)

Classical swine fever in India: current status and future perspective.

Science.gov (United States)

Singh, Vinod Kumar; Rajak, Kaushal Kishore; Kumar, Amit; Yadav, Sharad Kumar

2018-05-04

Classical swine fever (CSF) is a globally significant disease of swine caused by classical swine fever virus. The virus affects the wild boars and pigs of all age groups, leading to acute, chronic, late-onset or in-apparent course of the disease. The disease causes great economic loss to the piggery industry due to mortality, stunted growth, poor reproductive performance, and by impeding the international trade of pig and pig products. In India, CSF outbreaks are reported from most of the states wherever pig rearing is practiced and more frequently from northeast states. In spite of the highly devastating nature and frequent outbreaks, CSF remained underestimated and neglected for decades in India. The country requires rapid and sensitive diagnostic tests for an early detection of infection to limit the spread of the disease. Also, effective prophylactics are required to help in control and eradication of the disease for the development of the piggery industry. This review looks into the economic impact; epidemiology of CSF highlighting the temporal and spatial occurrence of outbreaks in the last two decades, circulation, and emergence of the virus genotypes in and around the country; and the constraints in the disease control, with the aim to update the knowledge of current status of the disease in India. The article also emphasizes the importance of the disease and the need to develop rapid specific diagnostics and effective measures to eradicate the disease.

Status of high temperature superconductor cable and fault current limiter projects at American Superconductor

International Nuclear Information System (INIS)

Maguire, J.F.; Yuan, J.

2009-01-01

This paper will describe the status of three key programs currently underway at American Superconductor Corp. The first program is the LIPA project which is a transmission voltage high temperature superconducting cable program, with funding support from the US Department of Energy. The 600 m cable, capable of carrying 574 MVA, was successfully installed and commissioned in LIPA grid on April 22, 2008. An overview of the project, system level design details and operational data will be provided. In addition, the status of the newly awarded LIPA II project will be described. The second program is Project Hydra, with funding support from the US Department of Homeland Security, to design, develop and demonstrate an HTS cable with fault current limiting functionality. The cable is 300 m long and is being designed to carry 96 MVA at a distribution level voltage of 13.8 kV. The cable will be permanently installed and energized in Manhattan, New York in 2010. The initial status of Project Hydra will be presented. The final program to be discussed is a transmission voltage, high temperature superconducting fault current limiter funded by the US DOE. The project encompasses the design, construction and test of a 115 kV FCL for power transmission within a time frame of 4-5 years. Installation and testing are planned for a Southern California Edison substation. A project overview and progress under the first phase will be reported.

Status of high temperature superconductor cable and fault current limiter projects at American Superconductor

Energy Technology Data Exchange (ETDEWEB)

Maguire, J.F., E-mail: jmaguire@amsc.co [American Superconductor Co., 64 Jackson Road, Devens, MA 01434 (United States); Yuan, J. [American Superconductor Co., 64 Jackson Road, Devens, MA 01434 (United States)

2009-10-15

This paper will describe the status of three key programs currently underway at American Superconductor Corp. The first program is the LIPA project which is a transmission voltage high temperature superconducting cable program, with funding support from the US Department of Energy. The 600 m cable, capable of carrying 574 MVA, was successfully installed and commissioned in LIPA grid on April 22, 2008. An overview of the project, system level design details and operational data will be provided. In addition, the status of the newly awarded LIPA II project will be described. The second program is Project Hydra, with funding support from the US Department of Homeland Security, to design, develop and demonstrate an HTS cable with fault current limiting functionality. The cable is 300 m long and is being designed to carry 96 MVA at a distribution level voltage of 13.8 kV. The cable will be permanently installed and energized in Manhattan, New York in 2010. The initial status of Project Hydra will be presented. The final program to be discussed is a transmission voltage, high temperature superconducting fault current limiter funded by the US DOE. The project encompasses the design, construction and test of a 115 kV FCL for power transmission within a time frame of 4-5 years. Installation and testing are planned for a Southern California Edison substation. A project overview and progress under the first phase will be reported.

Status of high temperature superconductor cable and fault current limiter projects at American Superconductor

Science.gov (United States)

Maguire, J. F.; Yuan, J.

2009-10-01

This paper will describe the status of three key programs currently underway at American Superconductor Corp. The first program is the LIPA project which is a transmission voltage high temperature superconducting cable program, with funding support from the US Department of Energy. The 600 m cable, capable of carrying 574 MVA, was successfully installed and commissioned in LIPA grid on April 22, 2008. An overview of the project, system level design details and operational data will be provided. In addition, the status of the newly awarded LIPA II project will be described. The second program is Project Hydra, with funding support from the US Department of Homeland Security, to design, develop and demonstrate an HTS cable with fault current limiting functionality. The cable is 300 m long and is being designed to carry 96 MVA at a distribution level voltage of 13.8 kV. The cable will be permanently installed and energized in Manhattan, New York in 2010. The initial status of Project Hydra will be presented. The final program to be discussed is a transmission voltage, high temperature superconducting fault current limiter funded by the US DOE. The project encompasses the design, construction and test of a 115 kV FCL for power transmission within a time frame of 4-5 years. Installation and testing are planned for a Southern California Edison substation. A project overview and progress under the first phase will be reported.

Current status of JENDL-3.3

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, Akira [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-03-01

Current status of JENDL-3.3 is presented. Reevaluation work toward JENDL-3.3 has started last April for three years project to supply a consolidated new versions of JENDL by JAERI NDC (Nuclear Data center) with the cooperation of JNDC (Japanese Nuclear Data Committee). The working schedule has been fixed by the careful review of the summary report, `The problems of JENDL-3.2`, submitted to JNDC last March after one year discussions by a small advisory group: `Identifying the problems of JENDL-3.2`. To cope with the problems, two new subgroups are set up in the Subcommittee of Nuclear Data of JNDC. One is Heavy Mass Elements Evaluation Working Group for the re-evaluation of major actinides (Th-232, U-233,235,236,238, Pu-236,239,241,242). The other is Intermediate Mass Elements Evaluation Working Group for solving the inconsistencies between calculations and integral experiments relating to the fields of fusion neutronics and shielding applications as well as new evaluations such as Er elements. Supplying covariance data for important nuclides are one of the main feature of JENDL-3.3. Re-evaluated data will be released as JENDL-3.3 in the individual bases after the reviewing process by the experts. (author)

Research productivity in Syria: Quantitative and qualitative analysis of current status

OpenAIRE

Diab, Maria M.; Taftaf, Rokana M. O.; Arabi, Mohammad

2011-01-01

Context: Scientific research output measured by the number and quality of publications reflects the research productivity of a certain community. Aims: To examine the quantity and quality of research produced by Syrian institutions with particular emphasis on the clinical and biomedical research. Settings and Design: Retrospective observational analysis of research originating from Syrian institutions indexed by Medline and Science Citation Index (SciVerse) Scopus bibliographic databases. Mat...

Radio Astronomy in Malaysia: Current Status and Outreach Activities

Science.gov (United States)

Hashim, N.; Abidin, Z. Z.; Ibrahim, U. F. S. U.; Umar, R.; Hassan, M. S. R.; Rosli, Z.; Hamidi, Z. S.; Ibrahim, Z. A.

2011-12-01

In this paper, we will present the current status of radio astronomical research and outreach in Malaysia. We will also present a short history of our research group, which is currently the only radio astronomical facility in Malaysia. Our group is called the Radio Cosmology Research Lab and was established in 2005 by Dr Zamri Zainal Abidin and Prof Dr Zainol Abidin Ibrahim. We will discuss the future plans for this group including our keen interest in being part of a more global network of radio astronomers. We are already an active member of the South-East Asia Astronomy Network (SEAAN) and aims to have a radio astronomical facility in order to join the Global Very Long Baseline Interferometer (VLBI) as well becoming a research hub for the future Square Kilometer Array (SKA) project. We will also present some of the scientific goals of our group including providing a platform for radio astronomers to be able to do observations of weak and high red-shifted radio objects such as galaxy clusters and supernovae.

Research Experience in Psychiatry Residency Programs Across Canada: Current Status

Science.gov (United States)

Shanmugalingam, Arany; Ferreria, Sharon G; Norman, Ross M G; Vasudev, Kamini

2014-01-01

Objective: To determine the current status of research experience in psychiatry residency programs across Canada. Method: Coordinators of Psychiatric Education (COPE) resident representatives from all 17 psychiatry residency programs in Canada were asked to complete a survey regarding research training requirements in their programs. Results: Among the 17 COPE representatives, 15 completed the survey, representing 88% of the Canadian medical schools that have a psychiatry residency program. Among the 15 programs, 11 (73%) require residents to conduct a scholarly activity to complete residency. Some of these programs incorporated such a requirement in the past 5 years. Ten respondents (67%) reported availability of official policy and (or) guidelines on resident research requirements. Among the 11 programs that have a research requirement, 10 (91%) require residents to complete 1 scholarly activity; 1 requires completion of 2 scholarly activities. Eight (53%) residency programs reported having a separate research track. All of the programs have a research coordinator and 14 (93%) programs provide protected time to residents for conducting research. The 3 most common types of scholarly activities that qualify for the mandatory research requirement are a full independent project (10 programs), a quality improvement project (8 programs), and assisting in a faculty project (8 programs). Six programs expect their residents to present their final work in a departmental forum. None of the residency programs require publication of residents’ final work. Conclusions: The current status of the research experience during psychiatry residency in Canada is encouraging but there is heterogeneity across the programs. PMID:25565474

Charged current weak interactions at high energy

International Nuclear Information System (INIS)

Cline, D.

1977-01-01

We review high energy neutrino and antineutrino charged current interactions. An overview of the experimental data is given, including a discussion of the experimental status of the y anomaly. Locality tests, μ-e universality and charge symmetry invariance tests are discussed. Charm production is discussed. The experimental status of trimuon events and possible phenomenological models for these events are presented. (orig.) [de

Radiopharmaceuticals in China. Current status and prospects

Energy Technology Data Exchange (ETDEWEB)

Jia, Hong-Mei; Liu, Bo-Li [Beijing Normal Univ. (China). Key Laboratory of Radiopharmaceuticals

2014-04-01

The review provides an overview of the current status of radiopharmaceuticals in China for in vivo clinical use and also describes some important advances in the past three decades. Development of the diagnostic and therapeutic radiopharmaceuticals as well as basic research on radiopharmaceutical chemistry are being introduced. The radiotracers developed in China include: (1) Brain perfusion imaging agents and CNS radiotracers for β-amyloid plaques, σ{sub 1} receptors, and dopamine D{sub 2} or D{sub 4} receptors; (2) {sup 99m}Tc- and {sup 18}F-labeled myocardial perfusion imaging agents; (3) tumor imaging agents including integrin-targeting radiotracer, novel sentinel lymph node imaging agents, hypoxia imaging agents, {sup 99m}Tc-labeled glucose derivatives, σ{sub 2} receptor imaging agents, folate receptor imaging agents, and potential radiotracers for imaging of human telomerase reverse transcriptase expression; (4) Potential infection imaging agents; (5) Potential asialoglycoprotein receptor imaging agents; (6) Other imaging agents. Moreover, some prospects of research and development of radiopharmaceuticals in the near future are discussed. (orig.)

Current Status of Operation and Management of Dental School Clinics.

Science.gov (United States)

Reinhardt, John W

2017-08-01

This article summarizes the current status of the operation and management of dental school clinics as schools strive to provide excellent patient-centered care in an environment that is educationally sound, efficient, and financially strong. Clinical education is a large component of dental education and an area in which many dental schools have an opportunity to enhance revenue. Clinical efficiencies and alternative models of clinical education are evolving in U.S. dental schools, and this article describes some of those evolutionary changes. This article was written as part of the project "Advancing Dental Education in the 21 st Century."

Current status of electron beam treatment of flue gas in China

International Nuclear Information System (INIS)

Wang Zhiguang

2006-01-01

Fossil resource especially coal will remain the main energy resource in China over the next 3 ∼4 decades. Pollution of flue gas from fossil power station is one problem being desiderated to solve since 1990's. Electron beam treatment of flue gas as an advanced technique has been developed and used by some institutes and industries in China. The current status of flue gas treatment using electron beam and the development of electron accelerator in China are reviewed. (author)

Environmental Programs: Status of Work and Current Priorities for FY13

Energy Technology Data Exchange (ETDEWEB)

Jones, Patricia [Los Alamos National Laboratory

2012-08-17

Presentation outline is: Mission/overview, Regulatory framework, Current status of cleanup, Shift in priorities to address highest risk, Removal of above-ground waste, Continued focus on protecting water resources, and Priorities for fiscal year 2013. LANL's Environmental Mission is to: (1) Repack and ship legacy transuranic waste containers; (2) Investigate and remediate Cold War (legacy) hazardous and radioactive waste areas; (3) Demolish unused buildings; (4) Disposition solid waste from Laboratory operations; and (5) Lifecycle cost nearly $3 billion.

Current status of relativistic core collapse simulations

Energy Technology Data Exchange (ETDEWEB)

Font, Jose A [Departamento de Astronomia y Astrofisica, Universidad de Valencia, Dr. Moliner 50, 46100 Burjassot (Valencia) (Spain)

2007-05-15

With the first generation of ground-based gravitational wave laser interferometers already taking data, the availability of reliable waveform templates from astrophysical sources, which may help extract the signal from the anticipated noisy data, is urgently required. Gravitational stellar core collapse supernova has traditionally been considered among the most important astrophysical sources of potentially detectable gravitational radiation. Only very recently the first multidimensional simulations of relativistic rotational core collapse have been possible (albeit for models with simplified input physics), thanks to the use of conservative formulations of the hydrodynamics equations and advanced numerical methodology, as well as stable formulations of Einstein's equations. In this paper, the current status of relativistic core collapse simulations is discussed, with the emphasis given to the modelling of the collapse dynamics and to the computation of the gravitational radiation in the existing numerical approaches. Work employing the conformally-flat approximation (CFC) of the 3+1 Einstein's equations is reported, as well as extensions of this approximation (CFC+) and investigations within the framework of the so-called BSSN formulation of the 3+1 gravitational field equations (with no approximation for the spacetime dynamics). On the other hand, the incorporation of magnetic fields and the MHD equations in numerical codes to improve the realism of core collapse simulations in general relativity, is currently an emerging field where significant progress is bound to be soon achieved. The paper also contains a brief discussion of magneto-rotational simulations of core collapse, aiming at addressing the effects of magnetic fields on the collapse dynamics and on the gravitational waveforms.

Current status of relativistic core collapse simulations

International Nuclear Information System (INIS)

Font, Jose A

2007-01-01

With the first generation of ground-based gravitational wave laser interferometers already taking data, the availability of reliable waveform templates from astrophysical sources, which may help extract the signal from the anticipated noisy data, is urgently required. Gravitational stellar core collapse supernova has traditionally been considered among the most important astrophysical sources of potentially detectable gravitational radiation. Only very recently the first multidimensional simulations of relativistic rotational core collapse have been possible (albeit for models with simplified input physics), thanks to the use of conservative formulations of the hydrodynamics equations and advanced numerical methodology, as well as stable formulations of Einstein's equations. In this paper, the current status of relativistic core collapse simulations is discussed, with the emphasis given to the modelling of the collapse dynamics and to the computation of the gravitational radiation in the existing numerical approaches. Work employing the conformally-flat approximation (CFC) of the 3+1 Einstein's equations is reported, as well as extensions of this approximation (CFC+) and investigations within the framework of the so-called BSSN formulation of the 3+1 gravitational field equations (with no approximation for the spacetime dynamics). On the other hand, the incorporation of magnetic fields and the MHD equations in numerical codes to improve the realism of core collapse simulations in general relativity, is currently an emerging field where significant progress is bound to be soon achieved. The paper also contains a brief discussion of magneto-rotational simulations of core collapse, aiming at addressing the effects of magnetic fields on the collapse dynamics and on the gravitational waveforms

Seismic proving test of ultimate piping strength (current status of preliminary tests)

International Nuclear Information System (INIS)

Suzuki, K.; Namita, Y.; Abe, H.; Ichihashi, I.; Suzuki, K.; Ishiwata, M.; Fujiwaka, T.; Yokota, H.

2001-01-01

In 1998 Fiscal Year, the 6 year program of piping tests was initiated with the following objectives: i) to clarify the elasto-plastic response and ultimate strength of nuclear piping, ii) to ascertain the seismic safety margin of the current seismic design code for piping, and iii) to assess new allowable stress rules. In order to resolve extensive technical issues before proceeding on to the seismic proving test of a large-scale piping system, a series of preliminary tests of materials, piping components and simplified piping systems is intended. In this paper, the current status of the material tests and the piping component tests is reported. (author)

Construction of natural radiation exposure study network - overview and current status

International Nuclear Information System (INIS)

Tokonami, Shinji

2010-01-01

A new project entitled 'Construction of natural radiation exposure study network' was adopted in the Program of Promotion of International Joint Research under the Special Coordination Funds for Promoting Science and Technology operated by the Ministry of Education, Culture, Sports, Science and Technology of Japan. Eight institutions were involved in this project and the project will continue until March, 2012. The aims of the project are to assess the dose for natural radiation exposures using state-of- the-art measurement techniques in four Asian countries (China, India, Korea and Thailand) and their outcomes will be distributed worldwide. Throughout the project, conventional measurement techniques will be improved and be optimized. More scientific data and results will be obtained as well. In particular, the following advanced technologies for inhalation exposures will be introduced: (1) Discriminative measurements of radon ( 222 Rn) and thoron ( 220 Rn) gases, (2) Evaluation of thoron decay products concentration, (3) Simple but effective particle size distribution measurements. In China, we are conducting a case-control study of radon and lung cancer in Gansu, China. This Gansu area was investigated in the past for the case-control study. New data are being accumulated. In India, we focused on Orissa in order to carry out radiation measurements in this project. In parallel, Kerala is currently involved as the comparative study area. In Korea, we are now measuring radon and thoron in radon/thoron prone areas. These results will give us new information for further understanding of exposure due to radon and thoron. In Thailand, we are carrying out comprehensively radiation measurements in NORM industries. Not only these surveys but also quality assurance of radon measurements are being addressed in Japan. We have managed an international intercomparison exercise of passive radon detectors at NIRS. This study presents an overview of the project and current status

Current status of cerebral glioma surgery in China.

Science.gov (United States)

Wu, Jin-song; Zhang, Jie; Zhuang, Dong-xiao; Yao, Cheng-jun; Qiu, Tian-ming; Lu, Jun-feng; Zhu, Feng-ping; Mao, Ying; Zhou, Liang-fu

2011-09-01

The treatment of gliomas is highly individualized. Surgery for gliomas is essentially for histological diagnosis, to alleviate mass effect, and most importantly, to favor longer survival expectancy. During the past two decades, many surgical techniques and adjuvants have been applied to glioma surgery in China, which lead to a rapid development in the field of cerebral glioma surgery. This article broadly and critically reviewed the existing studies on cerebral glioma surgery and to portrait the current status of glioma surgery in China. A literature search was conducted covering major innovative surgical techniques and adjuvants for glioma surgery in China. The following databases were searched: the Pubmed (January 1995 to date); China Knowledge Resource Integrated Database (January 1995 to date) and VIP Database for Chinese Technical Periodicals (January 1995 to date). A selection criterion was established to exclude duplicates and irrelevant studies. The outcome measures were extracted from included studies. A total of 3307 articles were initially searched. After excluded by abstracts and full texts, 69 studies conducted in the mainland of China were included and went through further analysis. The philosophy of surgical strategies for cerebral gliomas in China is undergoing tremendous change. Nowadays Chinese neurosurgeons pay more attention to the postoperative neurofunctional status of the patients. The aim of the glioma surgery is not only the more extensive tumor resection but also the maximal safety of intervention. The well balance of longer overall survival and higher quality of life should be judged with respect to each individual patient.

The World Nuclear Industry Status Report: 1992

International Nuclear Information System (INIS)

Flavin, Christopher; Lenssen, Nicholas; Froggatt, Antony; Willis, John; Kondakji, Assad; Schneider, Mycle

1992-05-01

The World Nuclear Industry Status Report provides a comprehensive overview of nuclear power plant data, including information on operation, production and construction. The WNISR assesses the status of new-build programs in current nuclear countries as well as in potential newcomer countries. This first WNISR Report was issued in 1992 in a joint publication with WISE-Paris, Greenpeace International and the World Watch Institute, Washington

Current status of managing food allergies in schools in Seoul, Korea.

Science.gov (United States)

Kim, Soyoung; Yoon, Jihyun; Kwon, Sooyoun; Kim, Jihyun; Han, Youngshin

2012-12-01

Recently the need to manage food allergies in schools has been growing. This study aimed to examine the current status of managing food allergies in schools in Seoul, Korea. A questionnaire survey was conducted in cooperation with the School Dietician Association during April 2009. Among the participating 154 schools, a total of 109 (71%) were determining students' food allergy status through parental surveys based on self-reported food allergies. A total of 72 (47%) had experienced student visits to a school health room due to food allergies within one year before the survey. Over 80 percent of the schools relied on self-care only without any school-wide measures for food allergies in place. Among the 890 menu items most frequently served in school lunch programs, a total of 664 (75%) were found to contain more than one food allergen. It is highly suggested that preventive plans and treatment measures should be established to manage food allergies in schools.

Current status and future outlook for bonded neodymium permanent magnets (invited)

International Nuclear Information System (INIS)

Croat, J.J.

1997-01-01

Bonded neodymium magnets can provide significant size and weight reduction and/or performance enhancement over sintered and, particularly, bonded ferrite permanent magnets and, moreover, provide these benefits at reasonable cost. Primarily for these reasons, these bonded magnets are now used in a wide and growing range of computer peripheral, office automation, and consumer electronic applications and now constitute the fastest growing segment of the permanent magnet market. The current status of these materials will be reviewed. Included is a brief overview of the manufacture of these magnetically isotropic magnets and a discussion of their unique properties and features from the perspective of both bonded magnet producer and user. Major applications are discussed as are some of the factors that will drive the market for these materials in the future. New technical developments, including the status and outlook for anisotropic bonded materials, high remanance isotropic materials and high temperature bonded magnets will also be discussed. copyright 1997 American Institute of Physics

Current status of thermoluminescence studies on minerals and rocks

International Nuclear Information System (INIS)

Sankaran, A.V.; Nambi, K.S.V.; Sunta, C.M.

1982-01-01

The usefulness of thermoluminescence (TL) in geological studies is being increasingly recognized, as may be judged from the considerable volume of literature accumulated over the past couple of decades; besides, a number of seminars, conferences and specialists' meetings have also been held on the subject of applied TL. However, these publications lie scattered over several periodicals and conference proceedings and an interested worker finds it difficult to obtain the gist of the contributions in one place. The present authors felt a need for this and have, therefore, attempted to bring together in this Report the current status of TL research about different minerals; applications in the fields of geochronology, ore-prospecting, stratigraphic correlation, geothermometry and other useful areas are also included. (author)

Current status of diuretic renography

International Nuclear Information System (INIS)

O'Reilly, P.H.

1987-01-01

Percutaneous antegrade perfusion studies constitute a valuable contribution to the investigation of obstructive uropathy. In 1978, the first report of application of diuretic renogram techniques to this problem appeared in the literature. This was the first systematic report of a standardized protocol to be applied to a specific surgical problem. The purpose of the procedure, as with perfusion pressure-flow studies, is to help distinguish between a dilated urinary tract that is obstructed and requires surgery and a nonobstructed system in which urographic dilation and stasis mimic obstruction, but no genuine impedance to urine flow exists, and surgery is not required. The technique provides dual information. It gives quantitative data on individual renal function that perfusion pressure-flow studies do not, and it gives time-activity curves reflecting the urodynamics through the individual upper urinary tracts at normal and high urinary flow rates. In the early days, this information was obtained from probe studies, but the procedure is now almost exclusively performed using the gamma camera, images from which give additional information on the site of any suspected obstruction. In some ways, the development of diuretic renography and that of perfusion pressure-flow studies have proceeded in a competitive fashion, both attempting to answer the same questions by different means. In practice, however, the two tests would be regarded as complementary, as will be shown later in this chapter. The following sections describe the technique of diuretic renography, its current clinical application and status in surgical and nuclear medicine practice, and its role in comparison with other available tests for management of the dilated upper urinary tract

Status of small ruminant production in six selected communities in ...

African Journals Online (AJOL)

The study examined the status of small ruminant production in some selected communities in Delta State vis-à-vis identifying the type of people involved in it; their response to modern livestock practices and determining factors affecting their stock size. Data were obtained from 90 respondents. Results of data analysis ...

Current status of research and development on remote maintenance for fusion components

International Nuclear Information System (INIS)

Takeda, Nobukazu; Kakudate, Satoshi; Nakahira, Masataka; Shibanuma, Kiyoshi

2008-01-01

There is a growing attention to remote maintenance of nuclear fusion reactors. Remote maintenance is planned in ITER tokamak to keep the health of in-vessel components like blankets and divertors. In this article, current status of the development in the remote maintenance equipments and methods, especially for ITER tokamak are reviewed. The newly developed vehicle type and boom type maintenance devices, manipulator, and transfer cask are illustrated. (J.P.N.)

The Influence of Topic Status on Written and Spoken Sentence Production

Science.gov (United States)

Cowles, H. Wind; Ferreira, Victor S.

2012-01-01

Four experiments investigate the influence of topic status and givenness on how speakers and writers structure sentences. The results of these experiments show that when a referent is previously given, it is more likely to be produced early in both sentences and word lists, confirming prior work showing that givenness increases the accessibility of given referents. When a referent is previously given and assigned topic status, it is even more likely to be produced early in a sentence, but not in a word list. Thus, there appears to be an early mention advantage for topics that is present in both written and spoken modalities, but is specific to sentence production. These results suggest that information-structure constructs like topic exert an influence that is not based only on increased accessibility, but also reflects mapping to syntactic structure during sentence production. PMID:22408281

Production regimes in four eastern boundary current systems

Science.gov (United States)

Carr, M. E.; Kearns, E. J.

2003-01-01

High productivity (maxima 3 g C m(sup -2)day(sup -1)) of the Eastern Boundary Currents (EBCs), i.e. the California, Peru-Humboldt, Canary and Benguela Currents, is driven by a combination of local forcing and large-scale circulation. The characteristics of the deep water brought to the surface by upwelling favorable winds depend on the large-scale circulation patterns. Here we use a new hydrographic and nutrient climatology together with satellite measurements ofthe wind vector, sea-surface temperature (SST), chlorophyll concentration, and primary production modeled from ocean color to quantify the meridional and seasonal patterns of upwelling dynamics and biological response. The unprecedented combination of data sets allows us to describe objectively the variability for small regions within each current and to characterize the governing factors for biological production. The temporal and spatial environmental variability was due in most regions to large-scale circulation, alone or in combination with offshore transport (local forcing). The observed meridional and seasonal patterns of biomass and primary production were most highlycorrelated to components representing large-scale circulation. The biomass sustained by a given nutrient concentration in the Atlantic EBCs was twice as large as that of the Pacific EBCs. This apparent greater efficiency may be due toavailability of iron, physical retention, or differences in planktonic community structure.

WIMP dark matter candidates and searches—current status and future prospects

Science.gov (United States)

Roszkowski, Leszek; Sessolo, Enrico Maria; Trojanowski, Sebastian

2018-06-01

We review several current aspects of dark matter theory and experiment. We overview the present experimental status, which includes current bounds and recent claims and hints of a possible signal in a wide range of experiments: direct detection in underground laboratories, gamma-ray, cosmic ray, x-ray, neutrino telescopes, and the LHC. We briefly review several possible particle candidates for a weakly interactive massive particle (WIMP) and dark matter that have recently been considered in the literature. We pay particular attention to the lightest neutralino of supersymmetry as it remains the best motivated candidate for dark matter and also shows excellent detection prospects. Finally we briefly review some alternative scenarios that can considerably alter properties and prospects for the detection of dark matter obtained within the standard thermal WIMP paradigm.

WIMP dark matter candidates and searches-current status and future prospects.

Science.gov (United States)

Roszkowski, Leszek; Sessolo, Enrico Maria; Trojanowski, Sebastian

2018-06-01

We review several current aspects of dark matter theory and experiment. We overview the present experimental status, which includes current bounds and recent claims and hints of a possible signal in a wide range of experiments: direct detection in underground laboratories, gamma-ray, cosmic ray, x-ray, neutrino telescopes, and the LHC. We briefly review several possible particle candidates for a weakly interactive massive particle (WIMP) and dark matter that have recently been considered in the literature. We pay particular attention to the lightest neutralino of supersymmetry as it remains the best motivated candidate for dark matter and also shows excellent detection prospects. Finally we briefly review some alternative scenarios that can considerably alter properties and prospects for the detection of dark matter obtained within the standard thermal WIMP paradigm.

Magnetic resonance imaging in psoriatic arthritis -- update on current status and future perspectives

DEFF Research Database (Denmark)

Østergaard, Mikkel; Poggenborg, René Panduro

2012-01-01

and future development of MRI and other modern imaging modalities in PsA. This review, presented at the GRAPPA 2010 annual meeting, describes the current status of MRI in PsA, with a focus on its use in diagnosis, monitoring, and prediction of the disease course and treatment response. Important areas...... for future research are also outlined....

Current status and requirements for position-sensitive detectors in medicine

CERN Document Server

Speller, R

2002-01-01

This review considers the current status of detector developments for medical imaging using ionising radiation. This field is divided into two major areas; the use of X-rays for transmission imaging and the use of radioactive tracers in emission imaging (nuclear medicine). Until recently, most detector developments were for applications in nuclear medicine. However, in the past 5 years new developments in large area, X-ray-sensitive detectors have meant that both application domains are equally served. In X-ray imaging, work in CT and mammography are chosen as examples of sensor developments. Photodiode arrays in multi-slice spiral CT acquisitions are described and for mammography the use of amorphous silicon flat panel arrays is considered. The latter is an excellent example where new detector developments have required a re-think of traditional imaging methods. In gamma-ray imaging the recent developments in small area, task-specific cameras are described. Their limitations and current proposals to overcome...

Charged and neutral current production of Δ(1236)

International Nuclear Information System (INIS)

Koerner, J.G.; Kobayashi, T.; Avilez, C.

1977-04-01

Based on a hybrid quark model approach previously developed by us which employs a q 2 -continuation in terms of generalized meson dominance form factors we study the weak production of the isobar Δ(1236). First we demonstrate that our model is in agreement with the Argonne data on charged current production of the Δ. We then study neutral current Δ-production using four different gauge models, namely the standard Weinberg-Salam model, a vector-like model with six quarks, a five quark model due to Achiman, Koller and Walsh and a variant of the Guersey-Sikivie model. We find that the results for the differential cross-section in the forward region are very sensitive to the structure of the weak neutral current and suggest that measurements in this region constitute a stringent test of weak interaction models. We also calculate the density matrix elements measurable from decay correllations. The density matrix elements are not so sensitive to the models containing some axial contribution whereas the vector-like model shows a behaviour quite distinct from the others. (orig.) [de

Fusion safety status report

International Nuclear Information System (INIS)

1986-10-01

This report includes information on a) tritium handling and safety; b) activation product generation and release; c) lithium safety; d) superconducting magnet safety; e) operational safety and shielding; f) environmental impact; g) recycling, decommissioning and waste management; and h) accident analysis. Recommendations for high priority research and development are presented, as well as the current status in each area

Plutonium metal exchange program : current status and statistical analysis

Energy Technology Data Exchange (ETDEWEB)

Tandon, L. (Lav); Eglin, J. L. (Judith Lynn); Michalak, S. E. (Sarah E.); Picard, R. R.; Temer, D. J. (Donald J.)

2004-01-01

The Rocky Flats Plutonium (Pu) Metal Sample Exchange program was conducted to insure the quality and intercomparability of measurements such as Pu assay, Pu isotopics, and impurity analyses. The Rocky Flats program was discontinued in 1989 after more than 30 years. In 2001, Los Alamos National Laboratory (LANL) reestablished the Pu Metal Exchange program. In addition to the Atomic Weapons Establishment (AWE) at Aldermaston, six Department of Energy (DOE) facilities Argonne East, Argonne West, Livermore, Los Alamos, New Brunswick Laboratory, and Savannah River are currently participating in the program. Plutonium metal samples are prepared and distributed to the sites for destructive measurements to determine elemental concentration, isotopic abundance, and both metallic and nonmetallic impurity levels. The program provides independent verification of analytical measurement capabilies for each participating facility and allows problems in analytical methods to be identified. The current status of the program will be discussed with emphasis on the unique statistical analysis and modeling of the data developed for the program. The discussion includes the definition of the consensus values for each analyte (in the presence and absence of anomalous values and/or censored values), and interesting features of the data and the results.

Current status of brachytherapy in Korea: a national survey of radiation oncologists.

Science.gov (United States)

Kim, Haeyoung; Kim, Joo Young; Kim, Juree; Park, Won; Kim, Young Seok; Kim, Hak Jae; Kim, Yong Bae

2016-07-01

The aim of the present study was to acquire information on brachytherapy resources in Korea through a national survey of radiation oncologists. Between October 2014 and January 2015, a questionnaire on the current status of brachytherapy was distributed to all 86 radiation oncology departments in Korea. The questionnaire was divided into sections querying general information on human resources, brachytherapy equipment, and suggestions for future directions of brachytherapy policy in Korea. The response rate of the survey was 88.3%. The average number of radiation oncologists per center was 2.3. At the time of survey, 28 centers (36.8%) provided brachytherapy to patients. Among the 28 brachytherapy centers, 15 (53.5%) were located in in the capital Seoul and its surrounding metropolitan areas. All brachytherapy centers had a high-dose rate system using (192)Ir (26 centers) or (60)Co (two centers). Among the 26 centers using (192)Ir sources, 11 treated fewer than 40 patients per year. In the two centers using (60)Co sources, the number of patients per year was 16 and 120, respectively. The most frequently cited difficulties in performing brachytherapy were cost related. A total of 21 centers had a plan to sustain the current brachytherapy system, and four centers noted plans to upgrade their brachytherapy system. Two centers stated that they were considering discontinuation of brachytherapy due to cost burdens of radioisotope source replacement. The present study illustrated the current status of brachytherapy in Korea. Financial difficulties were the major barriers to the practice of brachytherapy.

PV Status Report 2009. Research, Solar Cell Production and Market Implementation of Photovoltaics

International Nuclear Information System (INIS)

Jaeger-Waldau, A.

2009-08-01

Photovoltaics is a key technology option to realise the shift to a decarbonised energy supply. The solar resources in Europe and world wide are abundant and cannot be monopolised by one country. Regardless for what reasons and how fast the oil price and energy prices increase in the future, Photovoltaics and other renewable energies are the only ones to offer a reduction of prices rather than an increase in the future. As a response to the economic crisis, most of the G20 countries have designed economic recovery packages which include 'green stimulus' measures. However, compared to the new Chinese Energy Revitalisation Plan under discussion, the pledged investments in green energy are marginal. If no changes are made, China which now strongly supports its renewable energy industry, will emerge even stronger after the current financial crisis. In 2008, the Photovoltaic industry production almost doubled and reached a world-wide production volume of 7.3 GWp of Photovoltaic modules. Yearly growth rates over the last decade were in average more than 40%, which makes Photovoltaics one of the fastest growing industries at present. Business analysts predict the market volume to increase to 40 billion euros in 2010 and expect lower prices for consumers. The trend that thin-film Photovoltaics grew faster than the overall PV market continued in 2008. The Eighth Edition of the 'PV Status Report' tries to give an overview about the current activities regarding Research, Manufacturing and Market Implementation.

[Current status and potential perspectives in classical radiotherapy technology].

Science.gov (United States)

Dabić-Stanković, Kata M; Stanković, Jovan B; Radosević-Jelić, Ljiljana M

2004-01-01

After purchase of radiotherapy equipment in 2003, classic radiation therapy in Serbia will reach the highest world level. In order to define the highest standards in radiation technology, we analyzed the current status and potential perspectives of radiation therapy. An analysis of present situation in the USA, assumed as the most developed in the world, was done. Available data, collected in the last 3 years (equipment assortment, therapy modalities, workload and manpower) for 284 radiotherapy centers, out of potential 2050, were analyzed. Results were presented as crude percentage and matched to point current status. The analysis showed that CLINAC accelerators are the most popular (82.7%), as well as, ADAC (43.7%) and Focus (CMS) (27.4%) systems for therapy planning. Movement towards virtual simulation is evident (59.3%), although classic "simulation" is not fully eliminated from the radiotherapy chain. The most popular brachytherapy afterloader is Microselectron HDR (71%). About 64.4% centers use IMPAC communication/verification/record system that seems more open than Varis. All centers practice modern radiotherapy modalities and techniques (CPRT, IMRT, SRS/SRT, TBI, IORT, IVBHRT, HDR BHRT, etc.). CT and MRI availability is out of question, but PET is available in 3% of centers, however this percentage is rapidly growing. Up to 350 new patients per year are treated by one accelerator (about 35 pts. a day). Centers are relatively small and utilize 2-3 accelerators on average. Average FTE staffing norm is 4 radiation oncologists, 2-3 medical radiotherapy physicists, about 3 certified medical dosimetrists and about 6 radiotherapy technologists. In the past 5 years relative stagnation in classic radiotherapy has been observed. In spite of substantial investments in technology and consequent improvements, as well as wide introduction of computers in radiotherapy, radiotherapy results have not changed significantly. Vendor developement strategies do not point that

Current status in diabetic macular edema treatments

Institute of Scientific and Technical Information of China (English)

Pedro; Romero-Aroca

2013-01-01

Diabetes is a serious chronic condition,which increase the risk of cardiovascular diseases,kidney failure and nerve damage leading to amputation.Furthermore the ocular complications include diabetic macular edema,is the leading cause of blindness among adults in the industrialized countries.Today,blindness from diabetic macular edema is largely preventable with timely detection and appropriate interventional therapy.The treatment should include an optimized control of glycemia,arterial tension,lipids and renal status.The photocoagulation laser is currently restricted to focal macular edema in some countries,but due the high cost of intravitreal drugs,the use of laser treatment for focal and diffuse diabetic macular edema(DME),can be valid as gold standard in many countries.The intravitreal anti vascular endothelial growth factor drugs(ranibizumab and bevacizumab),are indicated in the treatment of all types of DME,but the correct protocol for administration should be defined for the different Retina Scientific Societies.The corticosteroids for diffuse DME,has a place in pseudophakic patients,but its complications restricted the use of these drugs for some patients.Finally the intravitreal interface plays an important role and its exploration is mandatory in all DME patients.

Plant cell engineering: current research, application and future prospects

International Nuclear Information System (INIS)

Wang Xunqing; Liu Luxiang

2008-01-01

This paper reviewed the current status of basic research in plant cell engineering, highlighted the application of embryo culture, double haploid (DH) technology, protoplast culture and somatic hybridization, somaclonal variation, rapid propagation, and bio-products production of plant-origin, and t he prospects. (authors)

Current status of uranium enrichment by way of chemical exchange reactions

International Nuclear Information System (INIS)

El Basyouny, A.; Bechthold, H.C.; Knoechel, A.; Vollmer, H.J.

1985-04-01

For this report, conference proceedings, patents and other types of literature have been collected to present an account of the current status of uranium enrichment by way of chemical exchange reactions. The report further presents a new concept along with the relevant process strategy developed by the authors. The principal process of the new concept is a chemical exchange process with crown ethers, complexed or free, playing an important part in the reactions. The authors also describe their experiments carried out for establishing suitable chemical systems. (orig./PW) [de

Dynamic Software Updating with Gosh! Current Status and the Road Ahead

DEFF Research Database (Denmark)

Gregersen, Allan Raundahl; Rasmussen, Michael; Jørgensen, Bo Nørregaard

2013-01-01

Any non-trivial software system has to be upgraded regularly to incorporate bug fixes and security patches or simply to keep up with the inevitable evolution in end-user requirements. Software upgrading is challenging, especially when it comes to online upgrading of running systems. In this paper......, we present the current status of Gosh!, a dynamic-software-updating system for Java, which provides comprehensive support for changing class definitions of live objects, including adding, removing and moving fields, methods, classes and interfaces anywhere in the inheritance hierarchy. Prior...

Current status of low-level-waste-segregation technology

International Nuclear Information System (INIS)

Clark, D.E.; Colombo, P.; Sailor, V.L.

1982-01-01

The adoption of improved waste segregation practices by waste generators and burial sites will result in the improved disposal of low-level wastes (LLW) in the future. Many of the problems connected with this disposal mode are directly attributable to or aggravated by the indiscriminate mixing of various waste types in burial trenches. Thus, subsidence effects, contact with ground fluids, movement of radioactivity in the vapor phase, migration of radionuclides due to the presence of chelating agents or products of biological degradation, deleterious chemical reactions, and other problems have occurred. Regulations are currently being promulgated which will require waste segregation to a high degree at LLW burial sites. The state-of-the-art of LLW segregation technology and current practices in the USA have been surveyed at representative facilities. Favorable experience has been reported at various sites following the application of segregation controls. This paper reports on the state-of-the-art survey and addresses current and projected LLW segregation practices and their relationship to other waste management activities

Current status of the HAL/S compiler on the Modcomp classic 7870 computer

Science.gov (United States)

Lytle, P. J.

1981-01-01

A brief history of the HAL/S language, including the experience of other users of the language at the Jet Propulsion Laboratory is presented. The current status of the compiler, as implemented on the Modcomp 7870 Classi computer, and future applications in the Deep Space Network (DSN) are discussed. The primary applications in the DSN will be in the Mark IVA network.

The current status of the Korean student health examination

Directory of Open Access Journals (Sweden)

Hye-Jung Shin

2013-08-01

Full Text Available Recent trends place an emphasis on school health care, the ultimate goal of which is to protect,maintain, and promote students’ health. School health care is a program that integrates health careservices, health education, health counseling, and local social health services. The student healthexamination (SHE system is a part of school health care and schools and communities must beavailable to provide professional health services. Pediatricians also have important roles as experts inboth school health care and the SHE system. In this article, the history of school health care, its legalbasis, and the current status of the SHE system in Korea are reviewed. Furthermore, sample surveysfrom the past few years are reviewed. Through this holistic approach, future directions are proposed forthe improvement of SHE and school health care.

Current Status of Mechanical Circulatory Support: A Systematic Review

Directory of Open Access Journals (Sweden)

Kyriakos Spiliopoulos

2012-01-01

Full Text Available Heart failure is a major public health problem and its management requires a significant amount of health care resources. Even with administration of the best available medical treatment, the mortality associated with the disease remains high. As therapeutical strategies for heart failure have been refined, the number of patients suffering from the disease has expanded dramatically. Although heart transplantation still represents the gold standard therapeutical approach, the implantation of mechanical circulatory support devices (MCSDs evolved to a well-established management for this disease. The limited applicability of heart transplantation caused by a shortage of donor organs and the concurrent expand of the patient population with end-stage heart failure led to a considerable utilization of MCSDs. This paper outlines the current status of mechanical circulatory support.

Marine renewable energy in China: Current status and perspectives

Directory of Open Access Journals (Sweden)

Yong-liang Zhang

2014-07-01

Full Text Available Based on a general review of marine renewable energy in China, an assessment of the development status and amount of various marine renewable energy resources, including tidal energy, tidal current energy, wave energy, ocean thermal energy, and salinity gradient energy in China's coastal seas, such as the Bohai Sea, the Yellow Sea, the East China Sea, and the South China Sea, is presented. We have found that these kinds of marine renewable energy resources will play an important role in meeting China's future energy needs. Additionally, considering the uneven distribution of China's marine renewable energy and the influences of its exploitation on the environment, we have suggested several sites with great potential for each kind of marine energy. Furthermore, perspectives on and challenges related with marine renewable energy in China are addressed.

Neurovirulence safety testing of mumps vaccines--historical perspective and current status.

Science.gov (United States)

Rubin, S A; Afzal, M A

2011-04-05

Many live, attenuated viral vaccines are derived from wild type viruses with known neurovirulent properties. To assure the absence of residual neurotoxicity, pre-clinical neurovirulence safety testing of candidate vaccines is performed. For mumps virus, a highly neurotropic virus, neurovirulence safety testing is performed in monkeys. However, laboratory studies suggest an inability of this test to correctly discern among virus strains of varying neurovirulence potential in man, and, further, some vaccines found to be neuroattenuated in monkeys were later found to be neurovirulent in humans when administered in large numbers. Over the past decade, concerted efforts have been made to replace monkey-based neurovirulence safety testing with more informative, alternative methods. This review summarizes the current status of mumps vaccine neurovirulence safety testing and insights into models currently approved and those under development. Published by Elsevier Ltd.

Current Status of Bioinks for Micro-Extrusion-Based 3D Bioprinting

Directory of Open Access Journals (Sweden)

Amit Panwar

2016-05-01

Full Text Available Recent developments in 3D printing technologies and design have been nothing short of spectacular. Parallel to this, development of bioinks has also emerged as an active research area with almost unlimited possibilities. Many bioinks have been developed for various cells types, but bioinks currently used for 3D printing still have challenges and limitations. Bioink development is significant due to two major objectives. The first objective is to provide growth- and function-supportive bioinks to the cells for their proper organization and eventual function and the second objective is to minimize the effect of printing on cell viability, without compromising the resolution shape and stability of the construct. Here, we will address the current status and challenges of bioinks for 3D printing of tissue constructs for in vitro and in vivo applications.

Current status of operation and utilization of the Dalat research reactor

International Nuclear Information System (INIS)

Nguyen Nhi Dien; Le Van So

2004-01-01

The Dalat Nuclear Research Reactor (DNRR) is a 500 kW swimming pool type reactor using the Soviet WWR-SM fuel assembly with 36% enrichment of U-235. It was upgraded from the USA 250 kW TRIGA Mark-II reactor. The first criticality of the renovated reactor was in November 1983 and its regular operation at nominal power of 500 kW has been since March 1984. The DNRR is operated mainly in continuous runs of 100 hrs, once every 4 weeks, for radioisotope production, neutron activation analyses and research purposes. The remaining time between two continuous runs is devoted to maintenance activities and also to short run for physics experiments and training purpose. From the first start-up to the end of December 2002, it totaled about 24,700 hrs of operation and the total energy released was 490 MWd. After 10 years of operation with the core of 89-fuel assembly configuration, in April 1994, the first refueling work was done and the 100-fuel assembly configuration was set-up. The second fuel reloading was executed in March 2002. At present time, the working configuration of the reactor core consists of 104 fuel assemblies. This fuel reloading will ensure efficient exploitation of the reactor for about 3 years with 1200-1300 hrs per year at nominal power. The current status of operation and utilization and some activities related to the reactor core management of the DNRR are presented and discussed in this paper. (author)

Current status of operation and utilization of the Dalat Research Reactor

International Nuclear Information System (INIS)

Nguyen Nhi Dien

2006-01-01

The Dalat Nuclear Research Reactor (DNRR) is a 500 kW pool-type reactor using the Soviet VVR-M2 fuel assembly with 36% enrichment of U-235. It was renovated and upgraded from the USA 250 kW TRIGA Mark-II reactor. The first criticality of the renovated reactor was in November 1983 and its regular operation at nominal power of 500 kW has been since March 1984. The DNRR is operated mainly in continuous runs of 100 hrs, once every 4 weeks, for radioisotope production, neutron activation analysis, scientific research and training. The remaining time between two continuous runs is devoted to maintenance activities and also to short run for reactor physics and thermal hydraulics experiments. From the first start-up to the end of December 2003, it totaled about 26,000 hrs of operation and the total energy released was about 515 MWd. After 10 years of operation with the core of 89-fuel assembly configuration, in April 1994, the first refueling work was done and the 100-fuel assembly configuration was set-up. The second fuel reloading was executed in March 2002. At present time, the working configuration of the reactor core consists of 104 fuel assemblies. The next fuel reloading has been planned at the end of 2004. The current status of operation and utilization of the DNRR is presented and discussed in this paper. (author)

The current status of orphan drug development in Europe and the US

OpenAIRE

Hall, Anthony K; Carlson, Marilyn R

2014-01-01

Orphan drug legislation has been introduced in a number of countries in order to stimulate the development of treatments for rare diseases by introducing commercial incentives for companies wishing to undertake that development. In order to navigate the maze of regulatory regulations and procedures so that companies can make proper use of the orphan drug incentives, specialist knowledge is required. This article will review the current status of orphan drug development in the EU and the US, e...

Nuclear power in the Asia-Pacific region. Current status and future perspective

International Nuclear Information System (INIS)

Hao, Jia; Otsuki, Takashi; Irie, Kazutomo

2017-01-01

This paper presents the current status and future perspective of nuclear power in the APEC region. We design three scenarios, including Low-nuclear Scenario, Business-as-Usual Scenario (BAU) as well as High-nuclear Scenario, in order to quantitatively evaluate contribution of nuclear power to the low-carbon energy system. Preliminary results from the modeling are presented in the paper, and the drivers and challenges for nuclear power development in the APEC region are discussed. (author)

Status of radiation sterilization of healthcare products in China

International Nuclear Information System (INIS)

Zhu Nankang; Wang Chunlei; Teng Weifang

2004-01-01

This paper describes the status of 60 Co radiation facilities both in service and under construction in China and examines the future market for radiation sterilization of healthcare products. Policies for developing the industry of radiation sterilization are also put forward; these include implementation of appropriate quality systems, scale-up and merging of existing radiation facilities, development of electron beam radiation for sterilization purposes and increasing awareness of the technology of radiation sterilization

Reconstituted products from oak

Science.gov (United States)

W. C. Lewis; B. G. Heebink

1971-01-01

"Reconstituted" describes a family of panel products made from fractionated oak, bonded with either a synthetic resin or a natural lignin bond. Several current commercial fiber panel products from oak are described, and the status of research on experimental products and processes is presented. Recent technological developments are removing the stigma...

Surveys of current status in biomedical science grant review: funding organisations' and grant reviewers' perspectives

DEFF Research Database (Denmark)

Schroter, Sara; Groves, Trish; Højgaard, Liselotte

2010-01-01

The objectives of this research were (a) to describe the current status of grant review for biomedical projects and programmes from the perspectives of international funding organisations and grant reviewers, and (b) to explore funders' interest in developing uniform requirements for grant review...

Current Status of the LOFAR EoR Key Science Project

Science.gov (United States)

Koopmans, L. V. E.; LOFAR EoR KSP Team

2018-05-01

A short status update on the LOFAR Epoch of Reionization (EoR) Key Science Project (KSP) is given, regarding data acquisition, data processing and analysis, and current power-spectrum limits on the redshifted 21-cm signal of neutral hydrogen at redshifts z = 8 - 10. With caution, we present a preliminary astrophysical analysis of ~60 hr of processed LOFAR data and their resulting power spectrum, showing that potentially already interesting limits on X-ray heating during the Cosmic Dawn can already be gained. This is by no means the final analysis of this sub-set of data, but illustrates the future potential when all nearly 3000 hr of data in hand on two EoR windows will have been processed.

A commentary on the current status and the future role of the European accident code

International Nuclear Information System (INIS)

Butland, A.T.D.

1990-01-01

This paper describes the history of the project to produce the European Accident code (EAC), leading to the planned release of a version of EAC-2 at the end of 1989. The requirements of a computer code to model the initiation phase of Hypothetical Core Disruptive Accidents (HCDAs) are discussed, paying particular attention to the lessons learnt in the CABRI project. The current status and content of the EAC-2 code are examined in relation to these requirements, noting how the sophisticated modelling plans for EAC-2 make it a benchmark code. The validation status of EAC-2 and future plans are discussed, noting that currently it consists solely of stand-alone validation of the modules used in EAC-2, rather than validation of the combined code. The future role of EAC-2 is briefly discussed in relation to the fast reactor plans in the EEC countries. (author)

Current status of RTO development and its implications for Canada

International Nuclear Information System (INIS)

MacDougall, M.

2002-01-01

This presentation includes a corporate review of Powerex, a review of Order 2000, and the current status of the Federal Energy Regulatory Commission's (FERC) efforts regarding Regional Transmission Operators (RTOs). Other topics of discussion include FERC's standard market design, an update of RTO West and implications for Canada. Powerex was incorporated in 1988 as a wholly-owned subsidiary of BC Hydro. British Columbia-based Powerex's heaviest trading is along the western-most states and Alberta, but it is slowly expanding into central and eastern markets. It evolved by selling and buying power at the United States Border. It received US FERC power marketing authorization in 1997 and has since seen sales jump from C$165 million to C$5.4 billion. Currently, the majority of power supply is from utilities other than BC Hydro. The presentation addresses issues such as the Federal Power Act, PUHCA and PURPA, and the 1992 Energy Policy Act which deals with expanded access to the power grid. Power Pool restructuring and FERC orders 888/889 are also discussed. 2 figs

Current status of RTO development and its implications for Canada

Energy Technology Data Exchange (ETDEWEB)

MacDougall, M. [Powerex Corp., Vancouver, BC (Canada)

2002-07-01

This presentation includes a corporate review of Powerex, a review of Order 2000, and the current status of the Federal Energy Regulatory Commission's (FERC) efforts regarding Regional Transmission Operators (RTOs). Other topics of discussion include FERC's standard market design, an update of RTO West and implications for Canada. Powerex was incorporated in 1988 as a wholly-owned subsidiary of BC Hydro. British Columbia-based Powerex's heaviest trading is along the western-most states and Alberta, but it is slowly expanding into central and eastern markets. It evolved by selling and buying power at the United States Border. It received US FERC power marketing authorization in 1997 and has since seen sales jump from C$165 million to C$5.4 billion. Currently, the majority of power supply is from utilities other than BC Hydro. The presentation addresses issues such as the Federal Power Act, PUHCA and PURPA, and the 1992 Energy Policy Act which deals with expanded access to the power grid. Power Pool restructuring and FERC orders 888/889 are also discussed. 2 figs.

Current status of surrogacy in Japan and uterine transplantation research.

Science.gov (United States)

Kisu, Iori; Banno, Kouji; Mihara, Makoto; Iida, Takuya; Yoshimura, Yasunori

2011-10-01

Recent advances in assisted reproductive technology (ART) have made it possible to circumvent many causes of male and female infertility. The right to have a child by ART has been respected for infertile couples. However, there are currently no legal regulations concerning ART in Japan, and this has resulted in social and ethical problems. Surrogacy involves particularly complex medical, ethical, social, and legal issues, and is frequently focused on as a major social concern. Uterine transplantation (UTx) is a potential alternative for young women with uterine factor infertility due to hysterectomy for treatment of a malignant uterine tumor or massive blood loss after delivery, or because of a congenital disease such as Mayer-Rokitansky-Küster syndrome. UTx has been examined in experimental animals as a basis for establishment of fecundity for young women with uterine factor infertility. In this review, we focus on surrogacy in Japan and UTx research, and discuss the current status and concerns in this field. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

STS operations planning - Current status and outlook for the future

Science.gov (United States)

Lee, C. M.

1981-01-01

Consideration is given to the status of Space Shuttle operations planning and outlook for the period 1982-94, with some speculations on Shuttle-related space operations early in the next century. Attention is given to the evolution of Shuttle payload capabilities over the next five years. The following list of near-earth environment factors to be exploited by the Space Shuttle is given: (1) easy control of gravity; (2) absence of atmosphere; (3) a comprehensive view of the earth's surface and atmosphere; (4) isolation of hazardous processes from earth biosphere; (5) freely available light, heat and photovoltaic power; (6) an infinite natural reservoir for the disposal of radioactive waste products; and (7) a super-cold heat sink.

Current status and future prospects of Japanese national project on coated conductor development and its applications

Science.gov (United States)

Shiohara, Y.; Yoshizumi, M.; Izumi, T.; Yamada, Y.

2008-09-01

Four years of the current five-year national project since 2003 for development of coated conductors using Y-system superconductors have passed and lots of remarkable results have been achieved. In this paper, the current status and the future prospect of this project are reviewed. The current national project comprises several groups of national laboratories, universities and private companies. The group of high performance tape development, consisting of Fujikura and SRL-NCCC, has worked on the tape by PLD-REBCO superconducting tapes on the PLD-CeO 2/IBAD-GZO buffered substrates. The high product of Ic and L equal to 112,166 A m was achieved in the 368 m-304.8 A GdBCO tape whose Ic value is mostly above 350 A/cm-w. The performance under the magnetic fields was also improved up to 42 A at 3 T in a GdBCO short film with doping of ZrO 2. About 61 m long GdBCO tape with ZrO 2 doping showed a high Ic value of 220 A at self field and 30 A at 3 T. On the other hand, the other group focusing on the low production cost has worked on processes of TFA-MOD and MOCVD, etc. The extremely high Ic value of 735 A/cm-w was attained in the TFA-MOD films on PLD-CeO 2/IBAD-GZO/Hastelloy C276 substrate by means of using the effect of Ba-poor nominal composition. In the efforts for long tape production, 200 m long tapes with high Ic values of 200 A/cm-w and 205 A/cm-w were obtained by MOD-YBCO/PLD-CeO 2/IBAD-GZO/Hastelloy C276 and PLD-HoBCO on buffered NiW substrate, respectively. The Ic × L value of the MOD-derived tape was 40,000 A m, which is the highest value in the world by the MOD process. Based on the above achievements on the coated conductor process development, two new additional goals were set in the project. One is the development for the extremely low cost tape and another is the development of the basic technologies for making the electric power devices including cables, transformers, motors, current-limiters and cryocoolers. Some of the new themes already revealed the

Current status and future prospects of Japanese national project on coated conductor development and its applications

International Nuclear Information System (INIS)

Shiohara, Y.; Yoshizumi, M.; Izumi, T.; Yamada, Y.

2008-01-01

Four years of the current five-year national project since 2003 for development of coated conductors using Y-system superconductors have passed and lots of remarkable results have been achieved. In this paper, the current status and the future prospect of this project are reviewed. The current national project comprises several groups of national laboratories, universities and private companies. The group of high performance tape development, consisting of Fujikura and SRL-NCCC, has worked on the tape by PLD-REBCO superconducting tapes on the PLD-CeO 2 /IBAD-GZO buffered substrates. The high product of I c and L equal to 112,166 A m was achieved in the 368 m-304.8 A GdBCO tape whose I c value is mostly above 350 A/cm-w. The performance under the magnetic fields was also improved up to 42 A at 3 T in a GdBCO short film with doping of ZrO 2 . About 61 m long GdBCO tape with ZrO 2 doping showed a high I c value of 220 A at self field and 30 A at 3 T. On the other hand, the other group focusing on the low production cost has worked on processes of TFA-MOD and MOCVD, etc. The extremely high I c value of 735 A/cm-w was attained in the TFA-MOD films on PLD-CeO 2 /IBAD-GZO/Hastelloy C276 substrate by means of using the effect of Ba-poor nominal composition. In the efforts for long tape production, 200 m long tapes with high I c values of 200 A/cm-w and 205 A/cm-w were obtained by MOD-YBCO/PLD-CeO 2 /IBAD-GZO/Hastelloy C276 and PLD-HoBCO on buffered NiW substrate, respectively. The I c x L value of the MOD-derived tape was 40,000 A m, which is the highest value in the world by the MOD process. Based on the above achievements on the coated conductor process development, two new additional goals were set in the project. One is the development for the extremely low cost tape and another is the development of the basic technologies for making the electric power devices including cables, transformers, motors, current-limiters and cryocoolers. Some of the new themes already

Current status of development in dry pyro-electrochemical technology of SNF reprocessing

International Nuclear Information System (INIS)

Bychkov, A.V.; Skiba, O.V.; Kormilitsyn, M.V.

2004-01-01

The technology of SNF management in molten salts currently developed by a group of institutes headed by RIAR has had several stages of development: - basic research of uranium, plutonium and main FP properties (investigation and reprocessing of different kinds of SNF in 1960 - 1970); - development of the equipment and implementation of the pyro-electrochemical technology of granulated UPu fuel production. Development of the vibro-packing method and in-pile testing of vibro-packed fuel pins with granulated fuel as the most 'logical' continuation of reprocessing: implementation of the technology for BOR-60 and BN-600 (1980 - 1990); - development of closed fuel cycle elements. Checking of the technology using batches of SNF. In-pile tests. Feasibility study of the closed fuel cycle (CFC). Study of application of the technology to other objects (transmutation; nitride, cermet and other fuels) (1980 - 1990). The current status of the research is the following: - Basic research. Properties of uranium, plutonium, thorium, and neptunium in chloride melts have been studied in much detail. The data on physical chemistry and electrochemistry of the main FP is enough for understanding the processes. Detailed studies of americium, curium, and technetium chemistry are the essential investigation directions; - Engineering development. The technology and equipment bases have been developed for the processes of oxide fuel reprocessing and fabrication. The technology was checked using 5500 kg of pure fuel from different reactors and 20 kg of irradiated BN-350 and BOR-60 fuel. The bases of the technology have been provided and the feasibility study has been carried out for a full-scale plant of BN-800 CFC; - Industrial application: Since the technology is highly prepared, the activities on industrial application of U-Pu fuel are now underway. The BOR-60 reactor uses fuel obtained by the dry method, the design of the facility for implementation of CFC reactors is being developed. 9

Microbiological risk factors in dentistry. Current status of knowledge.

Science.gov (United States)

Szymańska, Jolanta

2005-01-01

Dentists belong to a professional group potentially exposed to harmful biological factors which most often are infectious microorganisms, less frequently - allergenic or toxic microorganisms. The fundamental routes of spreading harmful microorganisms in a dental surgery are: blood-borne, saliva-droplet, direct contact with a patient and with infected equipment, and water-droplet infections. In this paper, the current status of knowledge on microbiological hazards in a dentist's work is presented. Groups of microorganisms, such as prions, viruses, bacteria, fungi and protozoa, to which a dentist is, or may be exposed, are discussed. Epidemiological assessment of microbiological hazards in a dentist's work was performed and the basic principles of prevention formulated. Special attention was given to microflora in dental unit waterlines, and the biofilm persisting in them, as a source of occupational hazards specific for a dentist's workplace.

Current status of high energy nucleon-meson transport code

Energy Technology Data Exchange (ETDEWEB)

Takada, Hiroshi; Sasa, Toshinobu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-03-01

Current status of design code of accelerator (NMTC/JAERI code), outline of physical model and evaluation of accuracy of code were reported. To evaluate the nuclear performance of accelerator and strong spallation neutron origin, the nuclear reaction between high energy proton and target nuclide and behaviors of various produced particles are necessary. The nuclear design of spallation neutron system used a calculation code system connected the high energy nucleon{center_dot}meson transport code and the neutron{center_dot}photon transport code. NMTC/JAERI is described by the particle evaporation process under consideration of competition reaction of intranuclear cascade and fission process. Particle transport calculation was carried out for proton, neutron, {pi}- and {mu}-meson. To verify and improve accuracy of high energy nucleon-meson transport code, data of spallation and spallation neutron fragment by the integral experiment were collected. (S.Y.)

Current status of spent fuel management in the Republic of Korea

International Nuclear Information System (INIS)

Min, D.K.; You, G.S.; Ro, S.G.; Park, H.S.

1999-01-01

Due to the lack of indigenous energy sources in Korea, the government selected nuclear energy as one of the major sources of electricity generation. According to the Korean government programme of a nuclear power development, currently, 14 nuclear power plants (NPPs) are in operation and 4 NPPs are under construction. In addition, further 10 NPPs are planned to be in operation by the year 2015. The large amount of spent fuel discharged from the nuclear power plants is accumulated in at-reactor (AR) storage pools. Due to the limited capacity of these AR storage pools, the safe and economic management of spent fuel is to be resolved. The spent fuel management strategy in Korea, basically depends on the interim storage in wet and dry storage facilities, including expansion of storage capacity. This paper describes the current status and plans of the spent fuel management in Korea. (author)

A study on current status of KAERI's international cooperation programs and strategies for effective implementation

International Nuclear Information System (INIS)

Kim, Kyoung Pyo; Park, Chun Kab; Noh, In Young; Kim, Young Min

1998-12-01

This is a report on the status and analysis of standard agreement for technical cooperation, expert mission service and technical staff attachment. This report comprises a total of six chapters. Chapter II discusses the status of the technical cooperation agreement which took effect late 1998, and various other model agreements for technical cooperation. Chapter III provides information on the status, regulations, procedures for the expert mission service, and Chapter IV details the current status of the technical staff attachment and the related procedures. Chapter V deals with the utilization status and analysis of the English Counselor, and Chapter VI is the Conclusion. This report has tow objectives. First, we have never published reference books related to standard agreement for technical cooperation, expert mission service and technical staff attachment necessary for international joint research until now. As a result, the research divisions have often asked many questions to the office of international cooperation. Therefore, we expect that many difficulties will be removed and procedures simplified if the research divisions use this report as a reference book. Second, we plan to use this report reference book for policy decisions after establishing the database. (author). 5 tabs., 9 figs

Productivity associated with visual status of computer users.

Science.gov (United States)

Daum, Kent M; Clore, Katherine A; Simms, Suzanne S; Vesely, Jon W; Wilczek, Dawn D; Spittle, Brian M; Good, Greg W

2004-01-01

The aim of this project is to examine the potential connection between the astigmatic refractive corrections of subjects using computers and their productivity and comfort. We hypothesize that improving the visual status of subjects using computers results in greater productivity, as well as improved visual comfort. Inclusion criteria required subjects 19 to 30 years of age with complete vision examinations before being enrolled. Using a double-masked, placebo-controlled, randomized design, subjects completed three experimental tasks calculated to assess the effects of refractive error on productivity (time to completion and the number of errors) at a computer. The tasks resembled those commonly undertaken by computer users and involved visual search tasks of: (1) counties and populations; (2) nonsense word search; and (3) a modified text-editing task. Estimates of productivity for time to completion varied from a minimum of 2.5% upwards to 28.7% with 2 D cylinder miscorrection. Assuming a conservative estimate of an overall 2.5% increase in productivity with appropriate astigmatic refractive correction, our data suggest a favorable cost-benefit ratio of at least 2.3 for the visual correction of an employee (total cost 268 dollars) with a salary of 25,000 dollars per year. We conclude that astigmatic refractive error affected both productivity and visual comfort under the conditions of this experiment. These data also suggest a favorable cost-benefit ratio for employers who provide computer-specific eyewear to their employees.

Review of Defence Plans in Europe: Current Status, Strengths and Opportunities

DEFF Research Database (Denmark)

De Boeck, Steven; Van Hertem, Dirk; Das, Kaushik

2016-01-01

interconnected, a contingency in one area can affect the whole power system and possibly lead to a wide area black out. Therefore adequate defence plans need to be designed and in place to handle these situations. This paper starts with an overview of the terminology used in defence plans. Subsequently...... the current status of defence plans in Europe and the preferred sequence of actions to mitigate contingencies, is given based on a survey conducted among several European TSOs. Furthermore his paper gives an overview of how the ongoing changes with renewables, phasor measurement units (PMUs), power flow...

Current status and recent developments of industrial radioisotope applications in Japan

International Nuclear Information System (INIS)

Tominaga, Hiroshi

1985-01-01

The current status of application of radioisotopes to industry in Japan is briefly reviewed. Radioisotope gauges are widely used in industry, but most of the radioactive tracer applications are performed in laboratories. as for the recent developments, it is noted that the majority of them are related to high technologies in industry. Some typical examples are described. They include: high accuracy coke moisture guage--dual channel gauging on-line analyzers based on 252 Cf, simultaneous neutron and gamma radiography; tracer techniques in civil engineering field, electronics industry, automobile industry and iron and steel industry.(M.G.B.)

Operational validation - current status and opportunities for improvement

International Nuclear Information System (INIS)

Davey, E.

2002-01-01

The design of nuclear plant systems and operational practices is based on the application of multiple defenses to minimize the risk of occurrence of safety and production challenges and upsets. With such an approach, the effectiveness of individual or combinations of design and operational features in preventing upset challenges should be known. A longstanding industry concern is the adverse impact errors in human performance can have on plant safety and production. To minimize the risk of error occurrence, designers and operations staff routinely employ multiple design and operational defenses. However, the effectiveness of individual or combinations of defensive features in minimizing error occurrence are generally only known in a qualitative sense. More importantly, the margins to error or upset occurrence provided by combinations of design or operational features are generally not characterized during design or operational validation. This paper provides some observations and comments on current validation practice as it relates to operational human performance concerns. The paper also discusses opportunities for future improvement in validation practice in terms of the resilience of validation results to operating changes and characterization of margins to safety or production challenge. (author)

Women's gambling behaviour, product preferences, and perceptions of product harm: differences by age and gambling risk status.

Science.gov (United States)

McCarthy, Simone; Thomas, Samantha L; Randle, Melanie; Bestman, Amy; Pitt, Hannah; Cowlishaw, Sean; Daube, Mike

2018-04-24

Women's participation in, and harm from gambling, is steadily increasing. There has been very limited research to investigate how gambling behaviour, product preferences, and perceptions of gambling harm may vary across subgroups of women. This study surveyed a convenience sample of 509 women from Victoria and New South Wales, Australia. Women were asked a range of questions about their socio-demographic characteristics and gambling behaviour. Focusing on four gambling products in Australia-casino gambling, electronic gambling machines (EGMs), horse betting, and sports betting-women were asked about their frequency of participation, their product preferences, and perceptions of product harms. The sample was segmented a priori according to age and gambling risk status, and differences between groups were identified using Chi-square tests and ANOVAs. Thematic analysis was used to interpret qualitative data. Almost two thirds (n = 324, 63.7%) of women had engaged with one of the four products in the previous 12 months. Compared to other age groups, younger women aged 16-34 years exhibited a higher proportion of problem gambling, gambled more frequently, and across more products. While EGMs were the product gambled on most frequently by women overall, younger women were significantly more likely to bet on sports and gamble at casinos relative to older women. Qualitative data indicated that younger women engaged with gambling products as part of a "night out", "with friends", due to their "ease of access" and perceived "chance of winning big". There were significant differences in the perceptions of the harms associated with horse and sports betting according to age and gambling risk status, with younger women and gamblers perceiving these products as less harmful. This study highlights that there are clear differences in the gambling behaviour, product preferences, and perceptions of product harms between subgroups of women. A gendered approach will enable public

Current Status of TRR-1/M1

International Nuclear Information System (INIS)

Sittichai, Chaiyut

2000-01-01

In 1961, the first Thai Research Reactor, TRR-1, having power of 1 MW was established. It was located at Office of Atomic Energy for Peace (OAEP) in Bangkok. TRR-1 was completely commissioned in June 1962. Plate typed high-enriched uranium (HEU) and U 3 O 8 -Al were used as fuel. Light water used as moderator and coolant. During 1975-1977, TRR-1 was shut down for modification. The reactor core and control system were disassembled and replaced by TRIGA Mark III. It is a circular hexagonal core typed reactor designed by General Atomics Company (GA). Afterwards, TRR-1 was officially renamed to Thai Research Reactor 1/Modification 1 (TRR-1/M1). TRR-1/M1 is a multipurpose reactor with nominal power of 2 MW. This swimming pool typed reactor uses low-enriched uranium (LEU) as fuel and light water as coolant and moderator. To date, the reactor has been operated with core No.12 that released power 1135 MWD to serve the user. The reactor has been serving for various kinds of utilization, for example, to produce radioisotope, neutron beam experiments and reactor physics experiments. This report explains in detail regarding operational experience and current status of this reactor, for example, reactor operation and reactor utilization. (author)

Current status of stereoscopic 3D LCD TV technologies

Science.gov (United States)

Choi, Hee-Jin

2011-06-01

The year 2010 may be recorded as a first year of successful commercial 3D products. Among them, the 3D LCD TVs are expected to be the major one regarding the sales volume. In this paper, the principle of current stereoscopic 3D LCD TV techniques and the required flat panel display (FPD) technologies for the realization of them are reviewed. [Figure not available: see fulltext.

Current status of theranostics in prostate cancer

Energy Technology Data Exchange (ETDEWEB)

Virgolini, Irene; Decristoforo, Clemens; Uprimny, Christian [Medical University of Innsbruck, Department of Nuclear Medicine, Innsbruck (Austria); Haug, Alexander [Medical University of Vienna, Department of Radiology and Nuclear Medicine, Vienna (Austria); Fanti, Stefano [University of Bologna, S. Orsola Hospital Bologna, Nuclear Medicine Unit, Bologna (Italy)

2018-03-15

The aim of this review is to report on the current status of prostate-specific membrane antigen (PSMA)-directed theranostics in prostate cancer (PC) patients. The value of {sup 68}Ga-PSMA-directed PET imaging as a diagnostic procedure for primary and recurrent PC as well as the role of evolving PSMA radioligand therapy (PRLT) in castration-resistant (CR)PC is assessed. The most eminent data from mostly retrospective studies currently available on theranostics of prostate cancer are discussed. The current knowledge on {sup 68}Ga-PSMA PET/CT implicates that primary staging with PET/CT is meaningful in patients with high-risk PC and that the combination with pelvic multi parametric (mp)MR (or PET/mpMR) reaches the highest impact on patient management. There may be a place for {sup 68}Ga-PSMA PET/CT in intermediate-risk PC patients as well, however, only a few data are available at the moment. In secondary staging for local recurrence, {sup 68}Ga-PSMA PET/mpMR is superior to PET/CT, whereas for distant recurrence, PET/CT has equivalent results and is faster and cheaper compared to PET/mpMR. {sup 68}Ga-PSMA PET/CT is superior to {sup 18}F / {sup 11}Choline PET/CT in primary staging as well as in secondary staging. In patients with biochemical relapse, PET/CT positivity is directly associated with prostate-specific antigen (PSA) increase and amounts to roughly 50% when PSA is raised to ≤0.5 ng/ml and to ≥90% above 1 ng/ml. Significant clinical results have so far been achieved with the subsequent use of radiolabeled PSMA ligands in the treatment of CRPC. Accumulated activities of 30 to 50 GBq of {sup 177}Lu-PSMA ligands seem to be clinically safe with biochemical response and PERCIST/RECIST response in around 75% of patients along with xerostomia in 5-10% of patients as the only notable side effect. On the basis of the current literature, we conclude that PSMA-directed theranostics do have a major clinical impact in diagnosis and therapy of PC patients. We recommend

Current Status of Nephron-Sparing Surgery (NSS) in the Management of Renal Tumours.

Science.gov (United States)

Venkatramani, Vivek; Swain, Sanjaya; Satyanarayana, Ramgopal; Parekh, Dipen J

2017-06-01

Nephron-sparing surgery has emerged as the surgical treatment of choice for small renal masses over the past two decades, replacing the traditional teaching of radical nephrectomy for renal cell carcinoma. With time, there has been an evolution in the techniques and indications for partial nephrectomy. This review summarizes the current status of nephron-sparing surgery for renal carcinoma and also deals with the future of this procedure.

Gastric Cancer: Current Status of Diagnosis and Treatment

International Nuclear Information System (INIS)

Takahashi, Tsunehiro; Saikawa, Yoshiro; Kitagawa, Yuko

2013-01-01

Gastric cancer is the second leading cause of death from malignant disease worldwide and most frequently discovered in advanced stages. Because curative surgery is regarded as the only option for cure, early detection of resectable gastric cancer is extremely important for good patient outcomes. Therefore, noninvasive diagnostic modalities such as evolutionary endoscopy and positron emission tomography are utilized as screening tools for gastric cancer. To date, early gastric cancer is being treated using minimally invasive methods such as endoscopic treatment and laparoscopic surgery, while in advanced cancer it is necessary to consider multimodality treatment including chemotherapy, radiotherapy, and surgery. Because of the results of large clinical trials, surgery with extended lymphadenectomy could not be recommended as a standard therapy for advanced gastric cancer. Recent clinical trials had shown survival benefits of adjuvant chemotherapy after curative resection compared with surgery alone. In addition, recent advances of molecular targeted agents would play an important role as one of the modalities for advanced gastric cancer. In this review, we summarize the current status of diagnostic technology and treatment for gastric cancer

Veterinary pharmacology: history, current status and future prospects.

Science.gov (United States)

Lees, P; Fink-Gremmels, J; Toutain, P L

2013-04-01

Veterinary therapeutics, based on the art of Materia Medica, has been practised for countless centuries, but the science of veterinary pharmacology is of very recent origin. This review traces the contribution of Materia Medica to veterinary therapeutics from the Egyptian period through to the Age of Enlightenment. The first tentative steps in the development of the science of veterinary pharmacology were taken in the 18th century, but it was not until the mid 20th century that the science replaced the art of Materia Medica. This review traces the 20th century developments in veterinary pharmacology, with emphasis on the explosion of knowledge in the 35 year period to 2010. The range of factors which have influenced the current status of the discipline are reviewed. Future developments are considered from the perspectives of what might be regarded as desirable and those innovations that might be anticipated. We end with words of encouragement for young colleagues intent upon pursuing a career in veterinary pharmacology. © 2013 Blackwell Publishing Ltd.

Collagen Cross-Linking: Current Status and Future Directions

Directory of Open Access Journals (Sweden)

Marine Hovakimyan

2012-01-01

Full Text Available Collagen cross-linking (CXL using UVA light and riboflavin (vitamin B2 was introduced as a clinical application to stabilize the cornea by inducing cross-links within and between collagen fibers. CXL has been investigated extensively and has been shown clinically to arrest the progression of keratoconic or post-LASIK ectasia. With its minimal cost, simplicity, and proven positive clinical outcome, CXL can be regarded as a useful approach to reduce the number of penetrating keratoplasties performed. Small case series have also indicated that CXL is beneficial in corneal edema by reducing stromal swelling behavior and in keratitis by inhibiting pathogen growth. Despite these encouraging results, CXL remains a relatively new method that is potentially associated with complications. Aspects such as side effects and recurrence rates have still to be elucidated. In light of the growing interest in CXL, our paper summarizes present knowledge about this promising approach. We have intentionally endeavored to include the more relevant studies from the recent literature to provide an overview of the current status of CXL.

Ventilator-associated pneumonia: current status and future recommendations.

Science.gov (United States)

Efrati, Shai; Deutsch, Israel; Antonelli, Massimo; Hockey, Peter M; Rozenblum, Ronen; Gurman, Gabriel M

2010-04-01

Ventilator-associated pneumonia (VAP) is a common hazardous complication in ICU patients. The aim of the current review is to give an update on the current status and future recommendations for VAP prevention. This article gives an updated review of the current literature on VAP. The first part briefly reviews pathogenesis and epidemiology while the second includes an in-depth review of evidence-based practice guidelines (EBPG) and new technologies developed for prevention of VAP. VAP remains a frequent and costly complication of critical illness with a pooled relative risk of 9-27% and mortality of 25-50%. Strikingly, VAP adds an estimated cost of more than $40,000 to a typical hospital admission. An important aetiological mechanism of VAP is gross or micro-aspiration of oropharyngeal organisms around the cuff of the endotracheal tube (ETT) into the distal bronchi. Prevention of VAP is preferable. Preventative measures can be divided into two main groups: the implemen- tation of EBPGs and use of device-based technologies. EBPGs have been authored jointly by the American Thoracic Society and the Infectious Diseases Society of America. The Canadian Critical Care Trials group also published VAP Guidelines in 2008. Their recommendations are detailed in this review. The current device-based technologies include drainage of subglottic secretions, silver coated ETTs aiming to influence the internal bio-layer of the ETT, better sealing of the lower airways with ultrathin cuffs and loops for optimal cuff pressure control. EBPG consensus includes: elevation of the head of the bed, use of daily "sedation vacations" and decontamination of the oropharynx. Technological solutions should aim to use the most comprehensive combination of subglottic suction of secretions, optimization of ETT cuff pressure and ultrathin cuffs. VAP is a type of hospital-acquired pneumonia that develops more than 48 h after endotracheal intubation. Its incidence is estimated to be 9-27%, with a

Current status of facilities dedicated to the production of synchrotron radiation

International Nuclear Information System (INIS)

1983-01-01

The use of synchrotron radiation has undergone a rapid growth in many areas of science during the past five years. Unforeseen fields have emerged, creating new opplortunities. In addition, there is a growing impact on many technological areas that will increase further on the emergence of new sources and experimental stations. The growth in the use of synchrotron radition has been so great that all existing experimental stations will be fully utilized when all current facilities in the United States begin full-time operation for users. Development of te remaining potential experimental stations at existing facilities will satisfy predicted demand until 1985. Insertion devices (wigglers and undulators) provide orders-of-magnitude brighter sources of radiation than bending magnets and are making possible new experiments not feasible, or even conceived, a few years ago

Current data warehousing and OLAP technologies’ status applied to spatial databases

Directory of Open Access Journals (Sweden)

Diego Orlando Abril Fradel

2007-01-01

Full Text Available Organisations require their information on a timely, dynamic, friendly, centralised and easy-to-access basis for analysing it and taking correct decisions at the right time. Centralisation can be achieved with data warehouse technology. On-line analytical processing (OLAP is used for analysis. Technologies using graphics and maps in data presentation can be exploited for an overall view of a company and helping to take better decisions. Geo- graphic information systems (GIS are useful for spatially locating information and representing it using maps. Data warehouses are generally implemented with a multidimensional data model to make OLAP analysis easier. A fundamental point in this model is the definition of measurements and dimensions; geography lies within such dimensions. Many researchers have concluded that the geographic dimension is another attribute for describing data in current analysis systems but without having an in-depth study of its spatial feature and without locating them on a map, like GIS does. Seen this way, interoperability is necessary between GIS and OLAP (called spatial OLAP or SOLAP and several entities are currently researching this. This document summarises the current status of such research.

Current status of regional hydrogeological studies and numerical simulations on geological disposal

International Nuclear Information System (INIS)

Nakao, Shinsuke; Kikuchi, Tsuneo; Ishido, Tsuneo

2004-01-01

Current status of regional hydrogeological studies on geological disposal including hydrogeological modeling using numerical simulators is reviewed in this report. A regional scale and boundary conditions of numerical models are summarized mainly from the results of the RHS (regional hydrogeological study) project conducted by Japan Nuclear Cycle Development Institute (JNC) in the Tono area. We also refer to the current conceptual modes of hydrology and numerical models of unsaturated zone flow at Yucca Mountain, Nevada, which is the arid site proposed for consideration as the United States' first underground high-level radioactive waste repository. Understanding behavior of a freshwater-saltwater transition zone seems to play a key role in the hydrogeological modeling in a coastal region. Technical features of a numerical simulator as a tool for geothermal reservoir modeling is also briefly described. (author)

Deep-well injection of liquid radwaste in Russia - current status and operations

International Nuclear Information System (INIS)

Bradley, D.J.; Foley, M.G.; Rybal'chenko, A.I.

1995-01-01

This paper is submitted as part of a coordinated effort to present the topic of deep-well injection. The companion paper, open-quotes Deep-Well Injection of Liquid Radwaste in Russia - Background and Technical Basis,close quotes focuses on the original decision to inject liquid radwaste, the research behind that decision, and the design and construction of the injection facilities. The emphasis in this paper is on the current status and operation of the well facilities and the control systems used to minimize environmental impact

The end of cheap oil: Current status and prospects

International Nuclear Information System (INIS)

Tsoskounoglou, Miltos; Ayerides, George; Tritopoulou, Efi

2008-01-01

This paper, analyses the factors impacting the price of crude oil in order to examine the likely evolution of the oil market and attempts to answer the question, whether cheap oil is already a thing of the past. Based on data made publicly available mostly by the major oil companies, it examines the effects of demand and supply, the evolution of world oil reserves, the trends in new discoveries of new oilfields, the evolution of world Gross Domestic Product (GDP), and the depletion of oil resources. The analysis concludes that the world peak in conventional oil production-the point beyond which oil production will irreversibly start declining-is approaching and will be reached, even according to the most optimistic scenarios, before 2040 and quite possibly much sooner. If the appropriate solutions for substituting crude oil and for conserving the use of energy are not implemented in time, then the current upward trend in oil prices is bound to continue

Bacterial Wilt in China: History, Current Status, and Future Perspectives

Science.gov (United States)

Jiang, Gaofei; Wei, Zhong; Xu, Jin; Chen, Huilan; Zhang, Yong; She, Xiaoman; Macho, Alberto P.; Ding, Wei; Liao, Boshou

2017-01-01

Bacterial wilt caused by plant pathogenic Ralstonia spp. is one of the most important diseases affecting the production of many important crops worldwide. In China, a large scientific community has been dedicated to studying bacterial wilt and its causative agent, Ralstonia pseudosolanacearum and R. solanacearum. Most of their work was published in Chinese, which has hindered international communication and collaboration in this field. In this review, we summarize the status of knowledge on geographical distribution, diversity, and host range of Ralstonia spp., as well as, the impact of bacterial wilt on important crops and disease control approaches, in China. We present areas of research and publications by Chinese scientists and propose the promotion of collaborative research within China and with the international community. PMID:28955350

Measurement of Neutrino Induced, Charged Current, Charged Pion Production

Energy Technology Data Exchange (ETDEWEB)

Wilking, Michael Joseph [Univ. of Colorado, Boulder, CO (United States)

2009-05-01

Neutrinos are among the least understood particles in the standard model of particle physics. At neutrino energies in the 1 GeV range, neutrino properties are typically determined by observing the outgoing charged lepton produced in a charged current quasi-elastic interactions. The largest charged current background to these measurements comes from charged current pion production interactions, for which there is very little available data.

The LHCf experiment at CERN motivations and current status

CERN Document Server

D'Alessandro, R; Bonechi, L; Bongi, M; Castellini, G; Faus, D A; Fukui, K; Grandi, M; Haguenauer, M; Itow, Y; Kasahara, K; Macina, D; Mase, T; Masuda, K; Matsubara, Y; Menjo, H; Mizuishi, M; Muraki, Y; Papini, P; Perrot, A L; Ricciarini, S; Sako, T; Shimizu, Y; Taki, K; Tamura, T; Torii, S; Tricomi, A; Turner, W C; Velasco, J; Viciani, A; Yoshida, K

2009-01-01

LHCf is an experiment currently installed at CERN at the LHC complex. It consists of two small calorimeters each one placed 140 meters away from the ATLAS interaction point. Their purpose is to study forward production of neutral particles in proton-proton collisions at extremely low angles. The results will provide invaluable inputs to the many air-shower Monte Carlo codes currently used for modeling cosmic rays interactions in the Earth atmosphere. Depending on machine start up, data will be taken from 900 GeV in the centre of mass up to 14 TeV (laboratory equivalent collision energy of 1017eV), thus covering an energy range up to and beyond the “knee” of the cosmic ray spectrum.

Current status of the reactor physics code WIMS and recent developments

International Nuclear Information System (INIS)

Lindley, B.A.; Hosking, J.G.; Smith, P.J.; Powney, D.J.; Tollit, B.S.; Newton, T.D.; Perry, R.; Ware, T.C.; Smith, P.N.

2017-01-01

Highlights: • The current status of the WIMS reactor physics code is presented. • Applications range from 2D lattice calculations up to 3D whole core geometries. • Gamma transport and thermal-hydraulic feedback models added. • Calculations methodologies described for several Gen II, III and IV reactor types. - Abstract: The WIMS modular reactor physics code has been under continuous development for over fifty years. This paper discusses the current status of WIMS and recent developments, in particular developments to the resonance shielding methodology and 3D transport solvers. Traditionally, WIMS is used to perform 2D lattice calculations, typically to generate homogenized reactor physics parameters for a whole core code such as PANTHER. However, with increasing computational resources there has been a growing trend for performing transport calculations on larger problems, up to and including 3D full core models. To this end, a number of the WIMS modules have been parallelised to allow efficient performance for whole core calculations, and WIMS includes a 3D method of characteristics solver with reflective and once-through tracking methods, which can be used to analyse problems of varying size and complexity. A time-dependent flux solver has been incorporated and thermal-hydraulic modelling capability is also being added to allow steady-state and transient coupled calculations to be performed. WIMS has been validated against a range of experimental data and other codes, in particular for water and graphite moderated thermal reactors. Future developments will include improved parallelization, enhancing the thermal-hydraulic feedback models and validating the WIMS/PANTHER code system for BWRs and fast reactors.

Evaluation and Management of Hepatic Encephalopathy: Current Status and Future Directions

Science.gov (United States)

Suraweera, Duminda; Sundaram, Vinay; Saab, Sammy

2016-01-01

Hepatic encephalopathy is a spectrum of neurocognitive manifestations often seen in patients with liver injury or rarely in patients with portosystemic shunting without liver injury. It can be divided into minimal (covert) hepatic encephalopathy and overt hepatic encephalopathy, depending on the severity. Patients with hepatic encephalopathy have compromised clinical outcomes, decreased quality of life, and increased healthcare utilization, often resulting in a heavy financial and personal burden on caregivers. The diagnosis remains largely clinical, with the exclusion of possible other causes for the altered mental status. Current treatment strategies include nonabsorbable disaccharides and antibiotics. This review will focus on the diagnosis, management and clinical impact of hepatic encephalopathy. PMID:27377741

Emerging memories: resistive switching mechanisms and current status

International Nuclear Information System (INIS)

Jeong, Doo Seok; Thomas, Reji; Katiyar, R S; Scott, J F; Kohlstedt, H; Petraru, A; Hwang, Cheol Seong

2012-01-01

The resistance switching behaviour of several materials has recently attracted considerable attention for its application in non-volatile memory (NVM) devices, popularly described as resistive random access memories (RRAMs). RRAM is a type of NVM that uses a material(s) that changes the resistance when a voltage is applied. Resistive switching phenomena have been observed in many oxides: (i) binary transition metal oxides (TMOs), e.g. TiO 2 , Cr 2 O 3 , FeO x and NiO; (ii) perovskite-type complex TMOs that are variously functional, paraelectric, ferroelectric, multiferroic and magnetic, e.g. (Ba,Sr)TiO 3 , Pb(Zr x Ti 1−x )O 3 , BiFeO 3 and Pr x Ca 1−x MnO 3 ; (iii) large band gap high-k dielectrics, e.g. Al 2 O 3 and Gd 2 O 3 ; (iv) graphene oxides. In the non-oxide category, higher chalcogenides are front runners, e.g. In 2 Se 3 and In 2 Te 3 . Hence, the number of materials showing this technologically interesting behaviour for information storage is enormous. Resistive switching in these materials can form the basis for the next generation of NVM, i.e. RRAM, when current semiconductor memory technology reaches its limit in terms of density. RRAMs may be the high-density and low-cost NVMs of the future. A review on this topic is of importance to focus concentration on the most promising materials to accelerate application into the semiconductor industry. This review is a small effort to realize the ambitious goal of RRAMs. Its basic focus is on resistive switching in various materials with particular emphasis on binary TMOs. It also addresses the current understanding of resistive switching behaviour. Moreover, a brief comparison between RRAMs and memristors is included. The review ends with the current status of RRAMs in terms of stability, scalability and switching speed, which are three important aspects of integration onto semiconductors. (review article)

Emerging memories: resistive switching mechanisms and current status

Science.gov (United States)

Jeong, Doo Seok; Thomas, Reji; Katiyar, R. S.; Scott, J. F.; Kohlstedt, H.; Petraru, A.; Hwang, Cheol Seong

2012-07-01

The resistance switching behaviour of several materials has recently attracted considerable attention for its application in non-volatile memory (NVM) devices, popularly described as resistive random access memories (RRAMs). RRAM is a type of NVM that uses a material(s) that changes the resistance when a voltage is applied. Resistive switching phenomena have been observed in many oxides: (i) binary transition metal oxides (TMOs), e.g. TiO2, Cr2O3, FeOx and NiO; (ii) perovskite-type complex TMOs that are variously functional, paraelectric, ferroelectric, multiferroic and magnetic, e.g. (Ba,Sr)TiO3, Pb(Zrx Ti1-x)O3, BiFeO3 and PrxCa1-xMnO3 (iii) large band gap high-k dielectrics, e.g. Al2O3 and Gd2O3; (iv) graphene oxides. In the non-oxide category, higher chalcogenides are front runners, e.g. In2Se3 and In2Te3. Hence, the number of materials showing this technologically interesting behaviour for information storage is enormous. Resistive switching in these materials can form the basis for the next generation of NVM, i.e. RRAM, when current semiconductor memory technology reaches its limit in terms of density. RRAMs may be the high-density and low-cost NVMs of the future. A review on this topic is of importance to focus concentration on the most promising materials to accelerate application into the semiconductor industry. This review is a small effort to realize the ambitious goal of RRAMs. Its basic focus is on resistive switching in various materials with particular emphasis on binary TMOs. It also addresses the current understanding of resistive switching behaviour. Moreover, a brief comparison between RRAMs and memristors is included. The review ends with the current status of RRAMs in terms of stability, scalability and switching speed, which are three important aspects of integration onto semiconductors.

Emotional or Behavioral Disorders: Background and Current Status of the E/BD Terminology and Definition.

Science.gov (United States)

Forness, Steven R.; Kavale, Kenneth A.

2000-01-01

This article reviews the development and current status of alternatives to the federal definition of emotional disturbance or behavior disorders. It notes that several states are now revising their own terminologies or definitions in response to the 1997 reauthorization of the Individuals with Disabilities Education Act that dropped the term…

Fossil energy waste management. Technology status report

Energy Technology Data Exchange (ETDEWEB)

Bossart, S.J.; Newman, D.A.

1995-02-01

This report describes the current status and recent accomplishments of the Fossil Energy Waste Management (FE WM) projects sponsored by the Morgantown Energy Technology Center (METC) of the US Department of Energy (DOE). The primary goal of the Waste Management Program is to identify and develop optimal strategies to manage solid by-products from advanced coal technologies for the purpose of ensuring the competitiveness of advanced coal technologies as a future energy source. The projects in the Fossil Energy Waste Management Program are divided into three types of activities: Waste Characterization, Disposal Technologies, and Utilization Technologies. This technology status report includes a discussion on barriers to increased use of coal by-products. Also, the major technical and nontechnical challenges currently being addressed by the FE WM program are discussed. A bibliography of 96 citations and a list of project contacts is included if the reader is interested in obtaining additional information about the FE WM program.

The current status of orphan drug development in Europe and the US.

Science.gov (United States)

Hall, Anthony K; Carlson, Marilyn R

2014-02-01

Orphan drug legislation has been introduced in a number of countries in order to stimulate the development of treatments for rare diseases by introducing commercial incentives for companies wishing to undertake that development. In order to navigate the maze of regulatory regulations and procedures so that companies can make proper use of the orphan drug incentives, specialist knowledge is required. This article will review the current status of orphan drug development in the EU and the US, explain the incentives and procedures, and touch on the role of patient organisations in the process.

A review on current status of municipal solid waste management in India.

Science.gov (United States)

Gupta, Neha; Yadav, Krishna Kumar; Kumar, Vinit

2015-11-01

Municipal solid waste management is a major environmental issue in India. Due to rapid increase in urbanization, industrialization and population, the generation rate of municipal solid waste in Indian cities and towns is also increased. Mismanagement of municipal solid waste can cause adverse environmental impacts, public health risk and other socio-economic problem. This paper presents an overview of current status of solid waste management in India which can help the competent authorities responsible for municipal solid waste management and researchers to prepare more efficient plans. Copyright © 2015. Published by Elsevier B.V.

Prospects and current status of B5 biodiesel implementation in Malaysia

International Nuclear Information System (INIS)

Yusoff, Mohd.Hizami Mohd.; Abdullah, Ahmad Zuhairi; Sultana, Shazia; Ahmad, Mushtaq

2013-01-01

This paper addresses B5 biodiesel programs in Malaysia, global challenges on the production of palm oil. Protective measures for future efficiency as well as continued viability of this renewable energy sector are also discussed. Crude palm oil (CPO) prices are currently suppressed because of high palm oil inventory. Malaysian government has taken a pro-active step in implementing the B5 biodiesel for transportation and industrial sectors through the introduction of B5 biodiesel. The B5 Biodiesel Program which was initially targeted at selected government agencies has been fully implemented for subsidized sectors in the Central Region. The promotion of B5 development is highly attractive due to its potential local feedstock from palm oil industry and the availability of production technologies that offer opportunities for the sustainable development in energy entrepreneurships. Nationally, produced B5 will improve the access to alternative energy services and is expected to help in improving productivity and sustainability. Despite successful local B5 implementation, Malaysia is recently facing global challenges on the biodiesel production which currently remains stagnant due to weak domestic demand and uncompetitive export tax structure. -- Highlights: •Prospects of B5 biodiesel implementation in Malaysia. •National Biofuel Policy thrusts pertinent to B5 program. •Successful application of B5 in government and industrial sectors. •Challenges in CPO production, weak domestic demand and export tax. •Reassessment of national policy according to global issues

Current Status of Postdoctoral and Graduate Programs in Dentistry.

Science.gov (United States)

Assael, Leon

2017-08-01

Advanced dental education has evolved in the context of societal needs and economic trends to its current status. Graduate programs have positioned their role in the context of health systems and health science education trends in hospitals, interprofessional clinical care teams, and dental schools and oral health care systems. Graduate dental education has been a critical factor in developing teams in trauma care, craniofacial disorders, pediatric and adult medicine, and oncology. The misalignment of the mission of graduate dental programs and the demands of private practice has posed a challenge in the evolution of programs as educational programs have been directed towards tertiary and indigent care while the practice community focuses on largely healthy affluent patients for complex clinical interventions. Those seeking graduate dental education today are smaller in number and include more international dental graduates than in the past. Graduate dental education in general dentistry and in the nine recognized dental specialties now includes Commission on Dental Accreditation (CODA) recognition of training standards as part of its accreditation process and a CODA accreditation process for areas of clinical education not recognized as specialties by the American Dental Association. Current types of programs include fellowship training for students in recognized specialties. This article was written as part of the project "Advancing Dental Education in the 21 st Century."

Current status of ITER I&C system as integration begins

Energy Technology Data Exchange (ETDEWEB)

Davis, William, E-mail: william.davis@iter.org [ITER Organisation, Route de Vinon-sur Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Wallander, Anders [ITER Organisation, Route de Vinon-sur Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Yonekawa, Izuru [Nippon Advanced Technology Ltd., 3129-45 Hibara Muramatsu, Tokai, Naka-gun, Ibaraki 319-1112 (Japan)

2016-11-15

Highlights: • The ITER I&C system is organisationally complicated and technically challenging. • Standard technologies for the ITER I&C systems have been selected. • Supply of non-standard technologies will cause serious issues. • Differing levels of design maturity of plant I&C systems is a serious challenge. • Systems are in the final stages of design and are being delivered to site. - Abstract: The ITER I&C system is organisationally complicated and technically challenging, and integrating its many sub-systems into a single coherent system is critical for the ITER project to meet its objectives. This paper explains the integration risks being faced now and anticipated in the near future. Standardisation initiatives by the ITER central team to mitigate these risks are described. The paper also presents the architecture of the ITER I&C system, the current status of design and manufacture key developments made in recent years, and the current and future activities of the central I&C teams. Finally, a short description is given of the plant I&C systems that will be delivered to ITER in the near future.

Current Status and Research into Overcoming Limitations of Capsule Endoscopy

Directory of Open Access Journals (Sweden)

Won Gun Kwack

2016-01-01

Full Text Available Endoscopic investigation has a critical role in the diagnosis and treatment of gastrointestinal (GI diseases. Since 2001, capsule endoscopy (CE has been available for small-bowel exploration and is under continuous development. During the past decade, CE has achieved impressive improvements in areas such as miniaturization, resolution, and battery life. As a result, CE is currently a first-line tool for the investigation of the small bowel in obscure gastrointestinal bleeding and is a useful alternative to wired enteroscopy. Nevertheless, CE still has several limitations, such as incomplete examination and limited diagnostic and therapeutic capabilities. To resolve these problems, many groups have suggested several models (e.g., controlled CO2 insufflation system, magnetic navigation system, mobile robotic platform, tagging and biopsy equipment, and targeted drug-delivery system, which are in development. In the near future, new technological advances will improve the capabilities of CE and broaden its spectrum of applications not only for the small bowel but also for the colon, stomach, and esophagus. The purpose of this review is to introduce the current status of CE and to review the ongoing development of solutions to address its limitations.

Current R and D status on material motion and interactions relevant to core disruptive accidents

Energy Technology Data Exchange (ETDEWEB)

Kondo, Satoru [Safety Engineering Division, O-arai Engineering Center, Power Reactor and Nuclear Fuel Development Corporation, O-arai, Ibaraki (Japan)

1994-07-01

In this paper, the current status of research and development activities are briefly reviewed on evaluation of material-coolant interactions and material movement and relocation relevant to the safety of liquid-metal fast reactors. Since the status of European activities are well summarized in other papers submitted to the present meeting, the activities in Japan and the United States are highlighted in this paper. The review includes: out-of-pile experiments, in-pile experiments and relevant computer code development. It is emphasized that improved understanding on material motion has contributed to establishing more realistic and rational safety evaluation methods, where various mitigation mechanisms are inherently effective. (author)

The Current Status of Baculovirus and Their Implication for Insect Pest Control

Directory of Open Access Journals (Sweden)

Arman Wijonarko

2001-07-01

Full Text Available Baculovirus have been promoted as the promising bioinsecticides for their pest control potential for more than half a century. But only a few have been successful as biological control agent, and almost none has been proven as commercial success, or widely used for large-scale insect pest control. The bioinsecticides currently represent only a small fraction of the world pesticide market. The successful of the Bt crop marked a special achievement in the bioinsecticide market growth. How about the baculoviruses? The main hurdle for baculovirus to be developed as bioinsecticide is its poor performance compare to synthetic chemical ones, include the speed of kill, and host range. It is important to understand the nature of baculovirus, and explore the possibilities to develop new way in applying the baculovirus as bioinsecticides. Key words: current status, baculovirus, insect control

Altered Mental Status: Current Evidence-based Recommendations for Prehospital Care

Directory of Open Access Journals (Sweden)

Ashley Sanello

2018-03-01

Full Text Available Introduction: In the United States emergency medical services (EMS protocols vary widely across jurisdictions. We sought to develop evidence-based recommendations for the prehospital evaluation and treatment of a patient with an acute change in mental status and to compare these recommendations against the current protocols used by the 33 EMS agencies in the State of California. Methods: We performed a literature review of the current evidence in the prehospital treatment of a patient with altered mental status (AMS and augmented this review with guidelines from various national and international societies to create our evidence-based recommendations. We then compared the AMS protocols of each of the 33 EMS agencies for consistency with these recommendations. The specific protocol components that we analyzed were patient assessment, point-of-care tests, supplemental oxygen, use of standardized scoring, evaluating for causes of AMS, blood glucose evaluation, toxicological treatment, and pediatric evaluation and management. Results: Protocols across 33 EMS agencies in California varied widely. All protocols call for a blood glucose check, 21 (64% suggest treating adults at <60mg/dL, and half allow for the use of dextrose 10%. All the protocols recommend naloxone for signs of opioid overdose, but only 13 (39% give specific parameters. Half the agencies (52% recommend considering other toxicological causes of AMS, often by using the mnemonic AEIOU TIPS. Eight (24% recommend a 12-lead electrocardiogram; others simply suggest cardiac monitoring. Fourteen (42% advise supplemental oxygen as needed; only seven (21% give specific parameters. In terms of considering various etiologies of AMS, 25 (76% give instructions to consider trauma, 20 (61% to consider stroke, and 18 (55% to consider seizure. Twenty-three (70% of the agencies have separate pediatric AMS protocols; others include pediatric considerations within the adult protocol. Conclusion: Protocols

The current implementation status of the integration of sports and physical activity into Dutch rehabilitation care.

Science.gov (United States)

Hoekstra, Femke; Hettinga, Florentina J; Alingh, Rolinde A; Duijf, Marjo; Dekker, Rienk; van der Woude, Lucas H V; van der Schans, Cees P

2017-01-01

To describe the current status of the nationwide implementation process of a sports and physical activity stimulation programme to gain insight into how sports and physical activity were integrated into Dutch rehabilitation care. The current implementation status of a sports and physical activity stimulation programme in 12 rehabilitation centres and 5 hospitals with a rehabilitation department was described by scoring fidelity and satisfaction. Seventy-one rehabilitation professionals filled out a questionnaire on how sports and physical activity, including stimulation activities, were implemented into rehabilitation care. Total fidelity scores (in %) were calculated for each organization. Professionals' satisfaction was rated on a scale from 1 to 10. In most organizations sports and physical activity were to some extent integrated during and after rehabilitation (fidelity scores: median = 54%, IQR = 23%). Physical activity stimulation was not always embedded as standard component of a rehabilitation treatment. Professionals' satisfaction rated a median value of 8.0 (IQR = 0.0) indicating high satisfaction rates. The fidelity outcome showed that activities to stimulate sports and physical activity during and after rehabilitation were integrated into rehabilitation care, but not always delivered as standardized component. These findings have emphasized the importance to focus on integrating these activities into routines of organizations. Implications for Rehabilitation Components of an evidence-based programme to stimulate sports and physical activity during and after rehabilitation can be used to measure the current status of the integration of sports and physical activity in rehabilitation care in a structural and effective way. The method described in the current study can be used to compare the content of the rehabilitation care regarding the integration of sports and physical activity among organizations both on a national and international level

Current status of construction license of PEFP

International Nuclear Information System (INIS)

Kim, J. Y.; Cho, J. S.; Min, Y. S.; Nam, J. M.; Jeon, G. P.; Park, S. S.; Jo, J. H.; Song, I. T.

2012-01-01

Since 2010 August, PEFP(Proton Engineering Frontier Project)'s Proton Accelerator Research Center has been under construction so far. Generally, in advance of construction startup, many kinds of licenses should be acquired along with the types of construction works. To acquire a license in time, each item should meet the standard by the related regulation, including not only procedural but also content aspect. In the advent of internet era, electronic government system has been adopted in many governmental functions: So is the national construction license acquisition system. Owing to the system, both approval and documentation functions in licensing are integrated in online computer network which provide us simplification in process and easy accessibility to license data. However, aside from these construction licenses, other types of licenses still remain separately managed: Machinery, electric facilities, and so on. Moreover, all the licenses have the priority order and take legal term in processing. So, to avoid any time delay in license acquisition, we organized license hierarchy and found out the priority among them. Thereafter, according to their legal term in approval and acquisition, whole license acquisition schedule was arranged and we completed all the necessary licenses acquisition in time In this study, we summarize the current status of license acquisition on Proton Accelerator Research Center Construction, and manifest how they have been and will be managed systematically

Current status of construction license of PEFP

Energy Technology Data Exchange (ETDEWEB)

Kim, J. Y.; Cho, J. S.; Min, Y. S.; Nam, J. M.; Jeon, G. P.; Park, S. S.; Jo, J. H.; Song, I. T. [KAERI, Daejeon (Korea, Republic of)

2012-10-15

Since 2010 August, PEFP(Proton Engineering Frontier Project)'s Proton Accelerator Research Center has been under construction so far. Generally, in advance of construction startup, many kinds of licenses should be acquired along with the types of construction works. To acquire a license in time, each item should meet the standard by the related regulation, including not only procedural but also content aspect. In the advent of internet era, electronic government system has been adopted in many governmental functions: So is the national construction license acquisition system. Owing to the system, both approval and documentation functions in licensing are integrated in online computer network which provide us simplification in process and easy accessibility to license data. However, aside from these construction licenses, other types of licenses still remain separately managed: Machinery, electric facilities, and so on. Moreover, all the licenses have the priority order and take legal term in processing. So, to avoid any time delay in license acquisition, we organized license hierarchy and found out the priority among them. Thereafter, according to their legal term in approval and acquisition, whole license acquisition schedule was arranged and we completed all the necessary licenses acquisition in time In this study, we summarize the current status of license acquisition on Proton Accelerator Research Center Construction, and manifest how they have been and will be managed systematically.

Current status and prospects of HIV treatment.

Science.gov (United States)

Cihlar, Tomas; Fordyce, Marshall

2016-06-01

Current antiviral treatments can reduce HIV-associated morbidity, prolong survival, and prevent HIV transmission. Combination antiretroviral therapy (cART) containing preferably three active drugs from two or more classes is required for durable virologic suppression. Regimen selection is based on virologic efficacy, potential for adverse effects, pill burden and dosing frequency, drug-drug interaction potential, resistance test results, comorbid conditions, social status, and cost. With prolonged virologic suppression, improved clinical outcomes, and longer survival, patients will be exposed to antiretroviral agents for decades. Therefore, maximizing the safety and tolerability of cART is a high priority. Emergence of resistance and/or lack of tolerability in individual patients require availability of a range of treatment options. Development of new drugs is focused on improving safety (e.g. tenofovir alafenamide) and/or resistance profile (e.g. doravirine) within the existing drug classes, combination therapies with improved adherence (e.g. single-tablet regimens), novel mechanisms of action (e.g. attachment inhibitors, maturation inhibitors, broadly neutralizing antibodies), and treatment simplification with infrequent dosing (e.g. long-acting injectables). In parallel with cART innovations, research and development efforts focused on agents that target persistent HIV reservoirs may lead to prolonged drug-free remission and HIV cure. Copyright © 2016 Gilead Sciences, Inc. Published by Elsevier B.V. All rights reserved.

Cognitive function in older adults according to current socioeconomic status.

Science.gov (United States)

Zhang, Michael; Gale, Shawn D; Erickson, Lance D; Brown, Bruce L; Woody, Parker; Hedges, Dawson W

2015-01-01

Cognitive function may be influenced by education, socioeconomic status, sex, and health status. Furthermore, aging interacts with these factors to influence cognition and dementia risk in late life. Factors that may increase or decrease successful cognitive aging are of critical importance, particularly if they are modifiable. The purpose of this study was to determine if economic status in late life is associated with cognition independent of socioeconomic status in early life. Cross-sectional demographic, socioeconomic, and cognitive function data were obtained in 2592 older adults (average age 71.6 years) from the Center for Disease Control's National Health and Nutrition Examination Survey (NHANES) and analyzed with linear regression modeling. Cognitive function, as measured with a test of processing speed, was significantly associated with poverty index scores after adjusting for educational attainment as an estimate of childhood socioeconomic status, ethnic background, age, health status, and sex (P status is independently associated with cognitive function in adults over age 60 years.

Current status of NPP generation IV

International Nuclear Information System (INIS)

Yohanes Dwi Anggoro; Dharu Dewi; Nurlaila; Arief Tris Yuliyanto

2013-01-01

Today development of nuclear technology has reached the stage of research and development of Generation IV nuclear power plants (advanced reactor systems) which is an innovative development from the previous generation of nuclear power plants. There are six types of power generation IV reactors, namely: Very High Temperature Reactor (VHTR), Sodium-cooled Fast Reactor (SFR), Gas-cooled Fast Reactor (GFR), Lead-cooled Fast Reactor (LFR), Molten Salt Reactor (MSR), and Super Critical Water-cooled Reactor (SCWR). The purpose of this study is to know the development of Generation IV nuclear power plants that have been done by the thirteen countries that are members of the Gen IV International Forum (GIF). The method used is review study and refers to various studies related to the current status of research and development of generation IV nuclear power. The result of this study showed that the systems and technology on Generation IV nuclear power plants offer significant advances in sustainability, safety and reliability, economics, and proliferation resistance and physical protection. In addition, based on the research and development experience is estimated that: SFR can be used optimally in 2015, VHTR in 2020, while NPP types GFR, LFR, MSR, and SCWR in 2025. Utilization of NPP generation IV said to be optimal if fulfill the goal of NPP generation IV, such as: capable to generate energy sustainability and promote long-term availability of nuclear fuel, minimize nuclear waste and reduce the long term stewardship burden, has an advantage in the field of safety and reliability compared to the previous generation of NPP and VHTR technology have a good prospects in Indonesia. (author)

Materials technology for fusion - Current status and future requirements

International Nuclear Information System (INIS)

Gold, R.E.; Bloom, E.E.; Clinard, F.W. Jr.; Smith, D.L.; Stevenson, R.D.; Wolfer, W.G.

1981-01-01

The general status of the materials research and development activities currently under way in support of controlled thermonuclear fusion reactors in the United States is reviewed. In the area of magnetic confinement configurations, attention is given to development programs for first wall materials, which are at various stages for possible austenitic stainless steels, high-strength Fe-Ni-Cr alloys, reactive and refractory metal alloys, specially designed long-range ordered and rapidly solidified alloys, and ferritic/martensitic steels, and for tritium breeding materials, electrical insulators, ceramics, and coolants. The development of materials for inertial confinement reactors is also surveyed in relation to the protection scheme employed for the first wall and the effects of pulsed neutron irradiation. Finally, the materials requirements and selection procedures for the ETF/INTOR and Starfire tokamak reactor designs are examined. Needs for the expansion of research on nonfirst-wall materials and inertial confinement fusion reactor material requirements are pointed out

The payloads of Advanced Virgo: current status and upgrades

Science.gov (United States)

Naticchioni, L.; Virgo Collaboration

2018-02-01

The development and integration of new detector payloads has been an important part of the Advanced Virgo (AdV) project, the major upgrade of the Virgo interferometric detector of Gravitational Waves, aiming to increase the detector sensitivity by one order of magnitude. During the integration phase of the new AdV payloads with monolithic suspension of mirrors we experienced systematic suspension failures later identified as caused by dust contamination of the vacuum system. In order to not postpone the detector commissioning, making possible to join the LIGO O2 observation run, the Collaboration decided to proceed with the integration of the payloads relying on steel wire suspensions for all the mirrors. In this proceeding the status of the currently integrated payloads is reported, including their angular control characterization and the Q-factor measurements for test mass steel wire suspensions. The payload upgrade for the re-integration of monolithic suspensions after the O2 run is reported in the last section.

Current status of Mycobacterium avium subspecies paratuberculosis infection in animals & humans in India: What needs to be done?

Directory of Open Access Journals (Sweden)

Ajay Vir Singh

2016-01-01

Full Text Available Mycobacterium avium subspecies paratuberculosis (MAP has emerged as a major health problem for domestic livestock and human beings. Reduced per animal productivity of domestic livestock seriously impacts the economics of dairy farming globally. High to very high bioload of MAP in domestic livestock and also in the human population has been reported from north India. Presence of live MAP bacilli in commercial supplies of raw and pasteurized milk and milk products indicates its public health significance. MAP is not inactivated during pasteurization, therefore, entering into human food chain daily. Recovery of MAP from patients with inflammatory bowel disease or Crohn's disease and animal healthcare workers suffering with chronic gastrointestinal problems indicate a close association of MAP with a number of chronic and other diseases affecting human health. Higher bioload of MAP in the animals increases the risk of exposure to the human population with MAP. This review summarizes the current status of MAP infection in animals as well as in human beings and also highlights the prospects of effective management and control of disease in animals to reduce the risk of exposure to human population.

Study of single pion production in antineutrino induced charged current interactions

International Nuclear Information System (INIS)

Bolognese, Teresa.

1978-01-01

Results are presented on the exclusive charged current antineutrino production of one pion using the data of the Gargamelle propane experiment at CERN PS. The isospin structure of the charged weak current is studied as well as the energy dependence of the total cross section for π - antineutrino production, which is compared with the prediction of Adler's model [fr

Current status and future prospects of Japanese national project on coated conductor development and its applications

Energy Technology Data Exchange (ETDEWEB)

Shiohara, Y. [Superconductivity Research Laboratory, ISTEC, Shinonome 1-10-13, Koto-ku, Tokyo 135-0062 (Japan)], E-mail: shiohara@istec.or.jp; Yoshizumi, M.; Izumi, T. [Superconductivity Research Laboratory, ISTEC, Shinonome 1-10-13, Koto-ku, Tokyo 135-0062 (Japan); Yamada, Y. [Superconductivity Research Laboratory, ISTEC, Nagoya Coated Conductor Center, 2-4-1, Mutsuno, Atsuta-ku, Nagoya 456-8587 (Japan)

2008-09-15

Four years of the current five-year national project since 2003 for development of coated conductors using Y-system superconductors have passed and lots of remarkable results have been achieved. In this paper, the current status and the future prospect of this project are reviewed. The current national project comprises several groups of national laboratories, universities and private companies. The group of high performance tape development, consisting of Fujikura and SRL-NCCC, has worked on the tape by PLD-REBCO superconducting tapes on the PLD-CeO{sub 2}/IBAD-GZO buffered substrates. The high product of I{sub c} and L equal to 112,166 A m was achieved in the 368 m-304.8 A GdBCO tape whose I{sub c} value is mostly above 350 A/cm-w. The performance under the magnetic fields was also improved up to 42 A at 3 T in a GdBCO short film with doping of ZrO{sub 2}. About 61 m long GdBCO tape with ZrO{sub 2} doping showed a high I{sub c} value of 220 A at self field and 30 A at 3 T. On the other hand, the other group focusing on the low production cost has worked on processes of TFA-MOD and MOCVD, etc. The extremely high I{sub c} value of 735 A/cm-w was attained in the TFA-MOD films on PLD-CeO{sub 2}/IBAD-GZO/Hastelloy C276 substrate by means of using the effect of Ba-poor nominal composition. In the efforts for long tape production, 200 m long tapes with high I{sub c} values of 200 A/cm-w and 205 A/cm-w were obtained by MOD-YBCO/PLD-CeO{sub 2}/IBAD-GZO/Hastelloy C276 and PLD-HoBCO on buffered NiW substrate, respectively. The I{sub c} x L value of the MOD-derived tape was 40,000 A m, which is the highest value in the world by the MOD process. Based on the above achievements on the coated conductor process development, two new additional goals were set in the project. One is the development for the extremely low cost tape and another is the development of the basic technologies for making the electric power devices including cables, transformers, motors, current

[Nutritional screening before surgery for esophageal cancer - current status and evaluation results].

Science.gov (United States)

Shimakawa, Takeshi; Asaka, Shinich; Sagawa, Masano; Shimazaki, Asako; Yamaguchi, Kentaro; Usui, Takebumi; Yokomizo, Hajime; Shiozawa, Shunichi; Yoshimatsu, Kazuhiko; Katsube, Takao; Naritaka, Yoshihiko

2014-10-01

The incidence of postoperative complications and mortality are usually higher in patients with preoperative malnutrition. Malnutrition often preexists, particularly in patients undergoing surgery for esophageal cancer, which is substantially invasive. It is therefore important to understand the nutritional condition of patients and actively control perioperative nutrition.Our hospital has been providing nutritional status screening for patients before resection of esophageal cancer, and we report the current status and evaluation results in this article.This screening included 158 patients requiring radical resection of esophageal cancer.Age, comorbidity with diabetes, body mass index(BMI), serum albumin(Alb), Onodera's prognostic nutritional index(PNI), and Glasgow prognostic score(GPS)were used as nutritional indicators to stratify patients for analysis.Evaluation parameters included the incidence of postoperative complications(any complication, pulmonary complications, psychiatric disorder, and anastomotic leakage)and rates of long-term postoperative hospitalization.The analysis indicated that age, BMI, serum Alb, PNI, and GPS are useful for predicting the onset of postoperative complications and prolonged postoperative hospitalization.For such patients, more active nutritional control should be provided.

Current Status of Carl Sagan Observatory in Mexico

Science.gov (United States)

Sanchez-Ibarra, A.

The current status of Observatory "Carl Sagan" (OCS) of University of Sonora is presented. This project was born in 1996 focused to build a small solar-stellar observatory completely operated by remote control. The observatory will be at "Cerro Azul", a 2480 m peak in one of the best regions in the world for astronomical observation, at the Sonora-Arizona desert. The OCS, with three 16 cm solar telescopes and a 55 cm stellar telescope is one of the cheapest observatories, valuated in US200,000 Added to its scientific goals to study solar coronal holes and Supernovae Type 1A, the OCS has a strong educative and cultural program in Astronomy to all levels. At the end of 2001, we started the Program "Constelacion", to build small planetariums through all the countries with a cost of only US80,000. Also, the webcast system for transmission of the solar observations from the prototype OCS at the campus, was expanded to webcast educational programs in Astronomy since July of this year, including courses and diplomats for Latin American people. All of these advances are exposed here.

The current status of theory evaluation in nursing.

Science.gov (United States)

Im, Eun-Ok

2015-10-01

To identify the current status of theory evaluation in nursing and provide directions for theory evaluation for future development of theoretical bases of nursing discipline. Theory evaluation is an essential component in development of nursing knowledge, which is a critical element in development of nursing discipline. Despite earlier significant efforts for theory evaluation in nursing, a recent decline in the number of theory evaluation articles was noted and there have been few updates on theory evaluation in nursing. Discussion paper. A total of 58 articles published from 2003-2014 were retrieved through searches using the PUBMED, PsyInfo and CINAHL. The articles were sorted by the area of evaluation and analysed to identify themes reflecting the theory evaluation process. Diverse ways of theory evaluation need to be continuously used in future theory evaluation efforts. Six themes reflecting the theory evaluation process were identified: (a) rarely using existing theory evaluation criteria; (b) evaluating specifics; (c) using various statistical analysis methods; (d) developing instruments; (e) adopting in practice and education; and (f) evaluating mainly middle-range theories and situation-specific theories. © 2015 John Wiley & Sons Ltd.

Thorium-based nuclear fuel: current status and perspectives

International Nuclear Information System (INIS)

1987-03-01

Until the present time considerable efforts have already been made in the area of fabrication, utilization and reprocessing of Th-based fuels for different types of reactors, namely: by FRG and USA - for HTRs; FRG and Brazil, Italy - for LWRs; India - for HWRs and FBRs. Basic research of thorium fuels and thorium fuel cycles are also being undertaken by Australia, Canada, China, France, FRG, Romania, USSR and other countries. Main emphasis has been given to the utilization of thorium fuels in once-through nuclear fuel cycles, but in some projects closed thorium-uranium or thorium-plutonium fuel cycles are also considered. The purpose of the Technical Committee on the Utilization of Thorium-Based Nuclear Fuel: Current Status and Perspective was to review the world thorium resources, incentives for further exploration, obtained experience in the utilization of Th-based fuels in different types of reactors, basic research, fabrication and reprocessing of Th-based fuels. As a result of the panel discussion the recommendations on future Agency activities and list of major worldwide activities in the area of Th-based fuel were developed. A separate abstract was prepared for each of the 9 papers in this proceedings series

76 FR 4284 - Grant of Authority for Subzone Status; Tulkoff Food Products, Inc. (Dehydrated Garlic), Baltimore...

Science.gov (United States)

2011-01-25

... Status; Tulkoff Food Products, Inc. (Dehydrated Garlic), Baltimore, MD Pursuant to its authority under..., has made application to the Board for authority to establish a special-purpose subzone at the garlic... garlic products at the Tulkoff Food Products, Inc., facility located in Baltimore, Maryland (Subzone 74C...

Growth and predicted productivity of Opuntia ficus-indica for current and elevated carbon dioxide

Energy Technology Data Exchange (ETDEWEB)

Nobel, P.S. (Univ. of California, Los Angeles (United States)); Garcia de Cortazar, V. (Univ. de Chile, Santiago (Chile))

Opuntia ficus-indica (L.) Mill., a prickly pear cactus cultivated worldwide for its fruits and stem segments, can have an annual dry weight productivity exceeding that of many crops. Using a recent introduced environmental productivity index (EPI), the influences of water status, temperature, and photosynthetically active radiation (PAR) on its productivity can be predicted. This investigation calculated the water index, the temperature index, and the PAR index, whose product equals EPI, for 169 sites distributed approximately uniformly across the contiguous USA for present climatic conditions as well as for those associated with an elevated CO{sub 2} concentration of 650 {mu}L L{sup {minus}1}. The effect of elevated CO{sub 2} on growth of O. ficus-indica was directly measured, and low temperature limitations on productivity were considered. The dry weight gain of O. ficus-indica during 6 mo in an environmental growth chamber was 23% greater at 650 compared with 350 {mu}L L{sup {minus}1} CO{sub 2} and increased as the duration of the wet period increased. For closely spaced plants that lead to a high productivity per unit ground area, EPI averaged about 0.10, except in desert regions where the water index lowered EPI, in the far North or South and at high elevations where the temperature index lowered EPI, and in the Northeast and Northwest where the PAR index lowered EPI. The predicted annual dry weight productivity for O. ficus-indica was 12.8 Mg ha{sup {minus}1} yr{sup {minus}1} under current conditions, and 16.3 Mg ha{sup {minus}1} yr{sup {minus}1} under those associated with 650 {mu}L L{sup {minus}1} CO{sub 2}.

Socioeconomic status and exposure to disinfection by-products in drinking water in Spain

Directory of Open Access Journals (Sweden)

Serra Consol

2011-03-01

Full Text Available Abstract Background Disinfection by-products in drinking water are chemical contaminants that have been associated with cancer and other adverse effects. Exposure occurs from consumption of tap water, inhalation and dermal absorption. Methods We determined the relationship between socioeconomic status and exposure to disinfection by-products in 1271 controls from a multicentric bladder cancer case-control study in Spain. Information on lifetime drinking water sources, swimming pool attendance, showering-bathing practices, and socioeconomic status (education, income was collected through personal interviews. Results The most highly educated subjects consumed less tap water (57% and more bottled water (33% than illiterate subjects (69% and 17% respectively, p-value = 0.003. These differences became wider in recent time periods. The time spent bathing or showering was positively correlated with attained educational level (p Conclusions The most highly educated subjects were less exposed to chlorination by-products through ingestion but more exposed through dermal contact and inhalation in pools and showers/baths. Health risk perceptions and economic capacity may affect patterns of water consumption that can result in differences in exposure to water contaminants.

Biomonitoring of intermittent rivers and ephemeral streams in Europe: Current practice and priorities to enhance ecological status assessments.

Science.gov (United States)

Stubbington, Rachel; Chadd, Richard; Cid, Núria; Csabai, Zoltán; Miliša, Marko; Morais, Manuela; Munné, Antoni; Pařil, Petr; Pešić, Vladimir; Tziortzis, Iakovos; Verdonschot, Ralf C M; Datry, Thibault

2018-03-15

Intermittent rivers and ephemeral streams (IRES) are common across Europe and dominate some Mediterranean river networks. In all climate zones, IRES support high biodiversity and provide ecosystem services. As dynamic ecosystems that transition between flowing, pool, and dry states, IRES are typically poorly represented in biomonitoring programmes implemented to characterize EU Water Framework Directive ecological status. We report the results of a survey completed by representatives from 20 European countries to identify current challenges to IRES status assessment, examples of best practice, and priorities for future research. We identify five major barriers to effective ecological status classification in IRES: 1. the exclusion of IRES from Water Framework Directive biomonitoring based on their small catchment size; 2. the lack of river typologies that distinguish between contrasting IRES; 3. difficulties in defining the 'reference conditions' that represent unimpacted dynamic ecosystems; 4. classification of IRES ecological status based on lotic communities sampled using methods developed for perennial rivers; and 5. a reliance on taxonomic characterization of local communities. Despite these challenges, we recognize examples of innovative practice that can inform modification of current biomonitoring activity to promote effective IRES status classification. Priorities for future research include reconceptualization of the reference condition approach to accommodate spatiotemporal fluctuations in community composition, and modification of indices of ecosystem health to recognize both taxon-specific sensitivities to intermittence and dispersal abilities, within a landscape context. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Current status and future developments of small and micro hydro in southern Africa

CSIR Research Space (South Africa)

Jonker Klunne, W

2012-05-01

Full Text Available -1 Current status and future developments of small and micro hydro in southern Africa Wim Jonker Klunne Council for Scientific and Industrial Research (CSIR) PO Box 395 Pretoria 0001 South Africa Introduction Small and micro hydropower... are renewable energy technologies that have large potential in the south- ern African region, both for grid and off-grid applications. Within the region a good understanding exists on the potential for large scale hydro with a substantial number of plants...

A Survey on Renewable Energy Development in Malaysia: Current Status, Problems and Prospects

OpenAIRE

Alam Syed Shah; Nor Nor Fariza Mohd; Ahmad Maisarah; Hashim Nik Hazrul Nik

2016-01-01

Energy demand in Malaysia is increasing over seven per cent a year, while forty per cent of the energy is supplied from conventional fossil fuel. However, a number of social barriers have mired the social acceptance of renewable energy among the users. This study investigates the current status of renewable energy, problems and future outlook of renewable energy in Malaysia. A total of 200 respondents were surveyed from Klang Valley in Malaysia. Majority of the respondents use energy to gener...

Alternative methods for skin irritation testing: the current status : ECVAM skin irritation task force report 1

NARCIS (Netherlands)

Botham, P.A.; Earl, L.K.; Fentem, J.H.; Roguet, R.; Sandt, J.J.M.

1998-01-01

The ECVAM Skin Irritation Task Force was established in November 1996, primarily to prepare a report on the current status of the development and validation of alternative tests for skin irritation and corrosion and, in particular, to identify any appropriate non-animal tests for predicting human

Current status of food irradiation in the world. Trend in Asia

International Nuclear Information System (INIS)

Kume, Tamikazu

2002-01-01

This review describes the current status of food irradiation in the world and particularly, its trends in Asia, based on the report of the economic scale investigation on the irradiation in United States and Japan (2001) and on the information of 12th International Meeting on Radiation Processing in France in 2001 and on personal communications. International Consultative Group on Food Irradiation promotes its activities of irradiation globally and 46 countries are affiliated. Food irradiation is allowed in 52 countries. In 1999, 257,000 t of food is irradiated in the world, of which 1/3 is due to spice. The facilities for the irradiation have such sources as 60 Co and 137 Cs γ-rays, electron beam of <10 MeV and X-ray with <5 MeV. Detection methods of irradiated foods are summarized by the project of Analytical Detection Methods for Irradiation Treatment of Foods. The US is the most advanced country in the irradiation and, in Japan, only irradiation of potato is permitted. The detailed present status is also described of Bangladesh, China (the irradiation is most widely conducted in the world), India, Indonesia, Korea, Malaysia, Thailand and Vietnam. Recently Australia and New Zealand have started the irradiation. (K.H.)

Mobile Learning in Nursing Undergraduates in China: Current Status, Attitudes and Barriers.

Science.gov (United States)

Xiao, Qian; Zhang, Qiannan; Wang, Lanlan; Wang, Yanling; Sun, Liu; Wu, Ying

2017-01-01

To explore the current status, attitudes and barriers of nursing undergraduates toward mobile learning, 157 nursing students were investigated. more than half of them used mobile learning frequently in past half year. The mean score of students' intention towards mobile learning was 10.5 (ranged from 6 to 15), and it related to students' gender, expected effect, ease of operation, influence of other students, self-learning management and perceived interest. Some barriers affected students' mobile learning. Therefore, students had positive attitude and perception toward mobile learning, then we should create enough conditions to promote students' mobile learning.

Maternal nutritional status, breast-milk production and newborn growth and development

International Nuclear Information System (INIS)

Concepcion, P.V.; Sanchez Jaeger, A.; Marino, A.

2000-01-01

Breast-feeding practice of Venezuelan mothers is very short (less than 3 months). In 1995, 52% of the lactating women stopped breast feeding before the first month. Exclusive breast-feeding is very infrequent, especially among low income women. The most important reasons for quitting breast feeding are: early weaning, working mothers in 'informal market', and lack of nutritional knowledge. There are new programs, from governmental (CONALAMA) and non-governmental (UNICEF) groups that improve this practice. There is little information regarding breast-milk production, composition, nutritional and socio-cultural behaviors of lactating women in Venezuela. With the goal of providing reliable information on this topic, we are studying maternal nutritional status, and breast-milk production of low SES mothers, and growth of their infants. In this study we selected isotopic methods to measure breast-milk intake, on the other hand, vitamin A contained in women breast milk was determined. Another objective of this project was to assess mother's vitamin A status according to the conjunctival impression cytology (CIC) and the retinol dose response (RDR) methodology. Mother body composition was determined through different skinfold measurements and body mass index (BMI). Also, the babies' growth during the first three months of breast-feeding was evaluated. During that period it was possible to evaluate vitamin A reserves and corporal composition of the mother and nutritional status of their infants. No important prevalence of vitamin A deficiency was detected (6.3%), high risk of malnutrition was demonstrated by SES (92%), and between 11 and 18% of the mother began the lactating period undernourished. (author)

Maternal nutritional status, breast-milk production and newborn growth and development

Energy Technology Data Exchange (ETDEWEB)

Concepcion, P V; Sanchez Jaeger, A; Marino, A [Centro de Investigaciones en Nutricion, Universidad de Carabobo, Valencia (Venezuela)

2000-07-01

Breast-feeding practice of Venezuelan mothers is very short (less than 3 months). In 1995, 52% of the lactating women stopped breast feeding before the first month. Exclusive breast-feeding is very infrequent, especially among low income women. The most important reasons for quitting breast feeding are: early weaning, working mothers in 'informal market', and lack of nutritional knowledge. There are new programs, from governmental (CONALAMA) and non-governmental (UNICEF) groups that improve this practice. There is little information regarding breast-milk production, composition, nutritional and socio-cultural behaviors of lactating women in Venezuela. With the goal of providing reliable information on this topic, we are studying maternal nutritional status, and breast-milk production of low SES mothers, and growth of their infants. In this study we selected isotopic methods to measure breast-milk intake, on the other hand, vitamin A contained in women breast milk was determined. Another objective of this project was to assess mother's vitamin A status according to the conjunctival impression cytology (CIC) and the retinol dose response (RDR) methodology. Mother body composition was determined through different skinfold measurements and body mass index (BMI). Also, the babies' growth during the first three months of breast-feeding was evaluated. During that period it was possible to evaluate vitamin A reserves and corporal composition of the mother and nutritional status of their infants. No important prevalence of vitamin A deficiency was detected (6.3%), high risk of malnutrition was demonstrated by SES (92%), and between 11 and 18% of the mother began the lactating period undernourished. (author)

A Study on the Current Status and Prospects of Development of the Tourism Services Market

Directory of Open Access Journals (Sweden)

Miroshnyk Mariia V.

2017-06-01

Full Text Available The article considers the world trends in the developmet of services market, and it has been determined that the service sector is about 70% of the world’s gross domestic product (GDP. It has been noted that the tourism sector is one of the largest in the world economy, and its market in terms of investment efficiency is among the highly profitable markets along with the gas and oil producing, industrial, and automotive markets. The tourism market in Ukraine is only about 2% of the country’s GDP, but has great potential for innovation development and tourism perspectives. Such a situation requires constant monitoring and analyzing, which makes the selected study relevant. The purpose of the article was to provide a comprehensive analysis of the current status of the market for tourism services in Ukraine and to determine the main tendencies in its further development. It has been found that the tourism industry sector in Ukraine is formed by three components: outbound (international, internal, and inbound (foreign tourism, the quantitative increase of which will increase the efficiency of the country’s tourism potential and reinforce its positive image abroad.

Current Status of QA For Nuclear Power Plants in Japan

International Nuclear Information System (INIS)

Nagoshi, Hitohiko

1986-01-01

It is the current status of QA and our QA experiences with nuclear power plants against the background of the Japanese social and business environment. Accordingly, in 1972, 'The Guidance for Quality Assurance in Construction of Nuclear Power Plants' based on U. S. 10CEF50 Appendix B, was published by the Japan Electric Association. 'Jug-4101 The Guide for Quality Assurance of Nuclear Power Plants' has been prepared by referring to the IAEA QA code. The Guide has been accepted by the Japanese nuclear industry and applied to the QA programs of every organization concerned therewith. The Japanese approach to higher quality will naturally be different from that of other countries because of Japan's cultural, social, and economic conditions. Even higher quality is being aimed at through the LWR Improvement and Standardization Program and coordinated quality assurance efforts

Production, detection, storage and release of spin currents

Directory of Open Access Journals (Sweden)

Michele Cini

2015-03-01

Full Text Available Background: Quantum rings connected to ballistic circuits couple strongly to external magnetic fields if the connection is not symmetric. Moreover, properly connected rings can be used to pump currents in the wires giving raise to a number of interesting new phenomena. At half filling using a time-dependent magnetic field in the plane of the ring one can pump a pure spin current, excited by the the spin–orbit interaction in the ring.Results: Such a magnetic current is even under time reversal and produces an electric field instead of the usual magnetic field. Numerical simulations show that one can use magnetizable bodies as storage units to concentrate and save the magnetization in much the same way as capacitors operating with charge currents store electric charge. The polarization obtained in this way can then be used on command to produce spin currents in a wire. These currents show interesting oscillations while the storage units exchange their polarizations.Conclusion: The magnetic production of spin currents can be a useful alternative to optical excitation and electric field methods.

Current status of JMTR refurbishment project

International Nuclear Information System (INIS)

Kaminaga, Masanori; Niimi, Motoji; Hori, Naohiko; Takahashi, Kunihiro; Kanno, Masaru; Nakagawa, Tetsuya; Nagao, Yoshiharu; Ishihara, Masahiro; Kawamura, Hiroshi

2010-02-01

The JMTR is a light water moderated and cooled, beryllium reflected tank- type reactor using LUE silicide plate-type fuels. Its thermal power is 50 MW, maximum thermal and fast neutron flux is 4x10 18 m -2 s -1 . First criticality was achieved in March 1968, and its operation was stopped from August, 2006 for the refurbishment. The refurbishment is scheduled from the beginning of FY2007 to the end of FY2010. The renewed and upgraded JMTR will be re-started from FY2011. An investigation on aged components (aged-investigation) was carried out for concrete structures of the JMTR reactor building, exhaust stack, etc., and for tanks in the primary cooling system, heat exchangers, pipes in the secondary cooling system, cooling tower, emergency generators and so on, in order to identify their integrity. The aged-investigation was carried out at the beginning of FY2007. As a result, some components were decided to replace from viewpoints of future maintenance and improvement of reliability, and some components or structures were decided to repair. A visual inspection of inner side of the pressure vessel was carried out using an underwater camera in FY2008, and no serious damage was observed. Up to now, refurbishment works are in progress according to the planned schedule. In FY2009, motors of primary cooling pumps, secondary cooling pumps, motors of drain pumps, pump in the primary water transfer line to the water purification system, beryllium reflector frame, low-voltage motor control centers are to be replaced. A nuclear instrumentation system, process control system, safety protection system and so on are to be replaced in FY2010. In this paper, current status of JMTR refurbishment project is presented. (author)

Drugs in development for toxoplasmosis: advances, challenges, and current status.

Science.gov (United States)

Alday, P Holland; Doggett, Joseph Stone

2017-01-01

Toxoplasma gondii causes fatal and debilitating brain and eye diseases. Medicines that are currently used to treat toxoplasmosis commonly have toxic side effects and require prolonged courses that range from weeks to more than a year. The need for long treatment durations and the risk of relapsing disease are in part due to the lack of efficacy against T. gondii tissue cysts. The challenges for developing a more effective treatment for toxoplasmosis include decreasing toxicity, achieving therapeutic concentrations in the brain and eye, shortening duration, eliminating tissue cysts from the host, safety in pregnancy, and creating a formulation that is inexpensive and practical for use in resource-poor areas of the world. Over the last decade, significant progress has been made in identifying and developing new compounds for the treatment of toxoplasmosis. Unlike clinically used medicines that were repurposed for toxoplasmosis, these compounds have been optimized for efficacy against toxoplasmosis during preclinical development. Medicines with enhanced efficacy as well as features that address the unique aspects of toxoplasmosis have the potential to greatly improve toxoplasmosis therapy. This review discusses the facets of toxoplasmosis that are pertinent to drug design and the advances, challenges, and current status of preclinical drug research for toxoplasmosis.

Charged-Current Neutral Pion production at SciBooNE

International Nuclear Information System (INIS)

Catala-Perez, J.

2009-01-01

SciBooNE, located in the Booster Neutrino Beam at Fermilab, collected data from June 2007 to August 2008 to accurately measure muon neutrino and anti-neutrino cross sections on carbon below 1 GeV neutrino energy. SciBooNE is studying charged current interactions. Among them, neutral pion production interactions will be the focus of this poster. The experimental signature of neutrino-induced neutral pion production is constituted by two electromagnetic cascades initiated by the conversion of the π 0 decay photons, with an additional muon in the final state for CC processes. In this poster, I will present how we reconstruct and select charged-current muon neutrino interactions producing π 0 's in SciBooNE.

IAEA occupational radiation protection programme: current status

International Nuclear Information System (INIS)

Deboodt, P.; Mrabit, K.

2006-01-01

As stated in Art.III.A.6 of its Statute, the International Atomic Energy Agency (commonly referred to as the Agency) is authorized to establish or adopt, in consultation and, where appropriate, in collaboration with the competent organs of the United Nations and with the specialized agencies concerned, standards of safety for protection of health and minimization of danger to life and property (including such standards for labour conditions), and to provide for the application of these standards to its own operation as well as to the operations making use of materials, services, equipment, facilities, and information made available by the Agency or at its request or under its control or supervision. The Agency s Occupational Radiation Protection Programme aims at harmonizing infrastructures for the control of radiation exposure of workers and for optimizing radiation protection in situation s of exposures due to external radiation and intakes of radionuclides from both artificial and natural sources of radiation. Under its regular and technical cooperation programmes, the Agency has been assigning high priority to both the establishment of safety standards for labour conditions and for the application of these standards through, Interalia, direct assistance under its technical cooperation (TC) programme, the rendering of services, the promotion of education and training, the fostering of information exchange and the coordination of research and development. The purpose of this paper is to present the current status and future IAEA activities in support of occupational radiation protection. (authors)

Current biodiesel production technologies: A comparative review

International Nuclear Information System (INIS)

Abbaszaadeh, Ahmad; Ghobadian, Barat; Omidkhah, Mohammad Reza; Najafi, Gholamhassan

2012-01-01

Highlights: ► In this paper we review the technologies related to biodiesel production. ► 4 Primary approaches reviewed are direct use and blending of oils, micro-emulsions, pyrolysis and transesterification method. ► Both advantages and disadvantages of the different biodiesel production methods are also discussed. ► The most common technology of biodiesel production is transesterification of oils. ► Selection of a transesterification method depends on the amount of FFA and water content of the feedstock. - Abstract: Despite the high energy demand in the industrialized world and the pollution problems caused by widespread use of fossil fuels, the need for developing renewable energy sources with less environmental impacts are increasing. Biodiesel production is undergoing rapid and extensive technological reforms in industries and academia. The major obstacle in production and biodiesel commercialization path is production cost. Thus, in previous years numerous studies on the use of technologies and different methods to evaluate optimal conditions of biodiesel production technically and economically have been carried out. In this paper, a comparative review of the current technological methods so far used to produce biodiesel has been investigated. Four primary approaches to make biodiesel are direct use and blending of vegetable oils, micro-emulsions, thermal cracking (pyrolysis) and transesterification. Transesterification reaction, the most common method in the production of biodiesel, is emphasized in this review. The two types of transestrification process; catalytic and non-catalytic are discussed at length in the paper. Both advantages and disadvantages of the different biodiesel production methods are also discussed.

Pediatric neurology training in Canada: current status and future directions.

Science.gov (United States)

Doja, Asif

2012-05-01

Child neurology training in Canada has changed considerably over time, with increasing requirements for standardized teaching of the fundamentals of child neurology and the CanMEDS competencies. We sought to determine the current status of child neurology training in Canada as well future directions for training. A web-based survey was sent to program directors (PD's) of active pediatric neurology training programs. General questions about the programs were asked, as well as about success at the Royal College of Physicians and Surgeons of Canada (RCPSC) exam, breakdown of rotations, views on CanMEDS roles and questions on the future of pediatric neurology. 9/9 PD's completed the survey. 96.5% of all trainees successfully passed their RCPSC exam from 2001-2006. Breakdowns of the number and type of rotations for each year of training were provided. All CanMEDS roles were deemed to be important by PD's and programs have developed unique strategies to teach and assess these roles.92.6% of trainees chose to go into academic practice, with the most popular subspecialty being epilepsy. All PD's favour joint training sessions particularly for neurogenetics and neuromuscular disease. Overall, PD's suggest recruitment for future child neurologists at the medical student level but are divided as to whether we are currently training too few or too many child neurologists. This survey provides a view of the current state of pediatric neurology training in Canada and suggestions for further development of post-graduate training. In particular, attention should be given to joint educational programs as well as urgently assessing the manpower needs of child neurologists.

Acute stroke magnetic resonance imaging: current status and future perspective

International Nuclear Information System (INIS)

Kloska, Stephan P.; Wintermark, Max; Engelhorn, Tobias; Fiebach, Jochen B.

2010-01-01

Cerebral stroke is one of the most frequent causes of permanent disability or death in the western world and a major burden in healthcare system. The major portion is caused by acute ischemia due to cerebral artery occlusion by a clot. The minority of strokes is related to intracerebral hemorrhage or other sources. To limit the permanent disability in ischemic stroke patients resulting from irreversible infarction of ischemic brain tissue, major efforts were made in the last decade. To extend the time window for thrombolysis, which is the only approved therapy, several imaging parameters in computed tomography and magnetic resonance imaging (MRI) have been investigated. However, the current guidelines neglect the fact that the portion of potentially salvageable ischemic tissue (penumbra) is not dependent on the time window but the individual collateral blood flow. Within the last years, the differentiation of infarct core and penumbra with MRI using diffusion-weighted images (DWI) and perfusion imaging (PI) with parameter maps was established. Current trials transform these technical advances to a redefined patient selection based on physiological parameters determined by MRI. This review article presents the current status of MRI for acute stroke imaging. A special focus is the ischemic stroke. In dependence on the pathophysiology of cerebral ischemia, the basic principle and diagnostic value of different MRI sequences are illustrated. MRI techniques for imaging of the main differential diagnoses of ischemic stroke are mentioned. Moreover, perspectives of MRI for imaging-based acute stroke treatment as well as monitoring of restorative stroke therapy from recent trials are discussed. (orig.)

TomoMINT - the current status and future plan of MINT's computed tomography scanner

International Nuclear Information System (INIS)

Kanesan Sinnakaruppan; Jaafar Abdullah

2000-01-01

TomoMINT, a second generation computed tomography scanner developed by MINT, is a powerful non-destructive evaluation (NDE) technique for producing two-dimensional cross-sectional images of an object without physically sectioning it. Characteristics of the internal structure of an object such as dimensions, shape, internal defects, density and component distribution are readily available from the scan. Tomographs of wood, metal components and concrete slabs have been successfully obtained from TomoMINT. This paper deals with the current status and future development of this scanner. (author)

Preparative Purification of Recombinant Proteins: Current Status and Future Trends

Directory of Open Access Journals (Sweden)

Mayank Saraswat

2013-01-01

Full Text Available Advances in fermentation technologies have resulted in the production of increased yields of proteins of economic, biopharmaceutical, and medicinal importance. Consequently, there is an absolute requirement for the development of rapid, cost-effective methodologies which facilitate the purification of such products in the absence of contaminants, such as superfluous proteins and endotoxins. Here, we provide a comprehensive overview of a selection of key purification methodologies currently being applied in both academic and industrial settings and discuss how innovative and effective protocols such as aqueous two-phase partitioning, membrane chromatography, and high-performance tangential flow filtration may be applied independently of or in conjunction with more traditional protocols for downstream processing applications.

SaudiVeg ecoinformatics: Aims, current status and perspectives

Directory of Open Access Journals (Sweden)

Mohamed A. El-Sheikh

2017-02-01

Full Text Available During the last decade many electronic databases of vegetation plots were established in many countries around the world. These databases contain valuable phytosociological information assisting both governmental and NGO (Non-governmental organizations agencies to formulate strategies and on-ground plans to manage and protect nature resources. This paper provides an account on aims, current status and perspectives of building of a vegetation database for the Central Region (Najd of Saudi Arabia – the founding element of the Saudi Vegetation Database (SVD. The data stored by the database are sample plots (vegetation relevés collected according to the field techniques of the Braun-Blanquet approach (lists of taxa accompanied by semi-quantitative cover assessment, and are accompanied by general vegetation characteristics such as vegetation layering and cover, information on life-form of the recorded species, geographical coordinates, altitude, soil typology, topography and many more. More than 2900 vegetation-plot records (relevés have so far been collected in the Najd region; of these more than 2000 have already been stored using the Turboveg database platform. These field records cover many habitats such as depressions, wadis (dry river beds, agricultural lands, sand dunes, sabkhas, and ruderal habitats. The ecological information collected in the database is currently the largest set of vegetation data collated into a database in the Middle East. These data are of great importance for biodiversity studies in Saudi Arabia, since the region is recording a loss of biodiversity at a fast rate due to environmental problems such as global warming and land-use changes. We envisage that this database would catalyze further data collection on vegetation of the entire Arabian Peninsula, and shall serve as one of the most important datasets for classification and mapping of the vegetation of the Kingdom of Saudi Arabia.

Current status, new frontiers and challenges in radiation biodosimetry using cytogenetic, transcriptomic and proteomic technologies

Energy Technology Data Exchange (ETDEWEB)

Fenech, Michael, E-mail: michael.fenech@csiro.au [Commonwealth Scientific and Industrial Research Organisation, Gate 13 Kintore Avenue, Adelaide, SA 5000 (Australia)

2011-09-15

Biodosimetric methods for determining exposure dose in individuals following a radiation accident are important for the health management of the exposed cohort and prioritisation of high dose exposure cases to receive emergency medical treatment. This brief review provides a succinct outline of (i) the current status of standard cytogenetic methods used in radiation biodosimetry; (ii) development of high-throughput systems for current standard cytogenetic methods; (iii) emerging minimally invasive methods; (iv) the impact of nutrition and genotype on observed dose-response relationships and (v) new frontiers in biodosimetry using molecular biology techniques such as transcriptomics and proteomics.

78 FR 4307 - Current Good Manufacturing Practice Requirements for Combination Products

Science.gov (United States)

2013-01-22

...-2009-N-0435] Current Good Manufacturing Practice Requirements for Combination Products AGENCY: Food and...) is issuing this regulation on the current good manufacturing practice (CGMP) requirements applicable... this subpart? (Sec. 4.2) D. What current good manufacturing practice requirements apply to my...

Status of fast reactor activities in the Russian Federation

Energy Technology Data Exchange (ETDEWEB)

Troyanov, M F; Rinejsjij, A A [Institute of Physics and Power Engineering, Obninsk (Russian Federation)

1992-07-01

The power production program was developed before the disintegration of the USSR and CIS. This report covers therefore the current status of power production and consumption in in republics of the former USSR with a separate chapter on the status of nuclear power. It covers some general results concerned with fast reactors operational experience and BN-600 power plant operational experience. This includes radiological conditions at the BN-600 and reactor core operating experience. Separate chapters are devoted to BN-350, BOR-60, BR-10 and BN-800 reactors. Work devoted to large-size reactor design are described including research and development and fabrication.

Status of fast reactor activities in the Russian Federation

International Nuclear Information System (INIS)

Troyanov, M.F.; Rinejsjij, A.A.

1992-01-01

The power production program was developed before the disintegration of the USSR and CIS. This report covers therefore the current status of power production and consumption in in republics of the former USSR with a separate chapter on the status of nuclear power. It covers some general results concerned with fast reactors operational experience and BN-600 power plant operational experience. This includes radiological conditions at the BN-600 and reactor core operating experience. Separate chapters are devoted to BN-350, BOR-60, BR-10 and BN-800 reactors. Work devoted to large-size reactor design are described including research and development and fabrication

Strategies of bringing drug product marketing applications to meet current regulatory standards.

Science.gov (United States)

Wu, Yan; Freed, Anita; Lavrich, David; Raghavachari, Ramesh; Huynh-Ba, Kim; Shah, Ketan; Alasandro, Mark

2015-08-01

In the past decade, many guidance documents have been issued through collaboration of global organizations and regulatory authorities. Most of these are applicable to new products, but there is a risk that currently marketed products will not meet the new compliance standards during audits and inspections while companies continue to make changes through the product life cycle for continuous improvement or market demands. This discussion presents different strategies to bringing drug product marketing applications to meet current and emerging standards. It also discusses stability and method designs to meet process validation and global development efforts.

Current status of Joint FAA/NASA Runway Friction Program

Science.gov (United States)

Yager, Thomas J.; Vogler, William A.

1989-01-01

Tests with specially instrumented NASA B-737 and FAA B-727 aircraft together with several different ground friction measuring devices have been conducted for a variety of runway surface types and wetness conditions. This effort is part of the Joint FAA/NASA Aircraft Ground Vehicle Runway Friction Program aimed at obaining a better understanding of aircraft ground handling performance under adverse weather conditions and defining relationships between aircraft and ground vehicle tire friction measurements. Aircraft braking performance on dry, wet, snow-, and ice-covered runway conditions is discussed together with ground vehicle friction data obtained under similar runway conditions. For the wet, compacted snow- and ice-covered runway conditions, the relationship between ground vehicles and aircraft friction data is identified. The influence of major test parameters on friction measurements such as speed, test tire characteristics, and surface contaminant type are discussed. The test results indicate that use of properly maintained and calibrated ground vehicles for monitoring runway friction conditions should be encouraged particularly under adverse weather conditions. The current status of the runway friction program is summarized and future test plans are identified.

Plague in Iran: its history and current status

Directory of Open Access Journals (Sweden)

Abdolrazagh Hashemi Shahraki

2016-07-01

Full Text Available OBJECTIVES: Plague remains a public health concern worldwide, particularly in old foci. Multiple epidemics of this disease have been recorded throughout the history of Iran. Despite the long-standing history of human plague in Iran, it remains difficult to obtain an accurate overview of the history and current status of plague in Iran. METHODS: In this review, available data and reports on cases and outbreaks of human plague in the past and present in Iran and in neighboring countries were collected, and information was compiled regarding when, where, and how many cases occurred. RESULTS: This paper considers the history of plague in Persia (the predecessor of today’s Iran and has a brief review of plague in countries in the World Health Organization Eastern Mediterranean Region, including a range of countries in the Middle East and North Africa. CONCLUSIONS: Since Iran has experienced outbreaks of plague for several centuries, neighboring countries have reported the disease in recent years, the disease can be silent for decades, and the circulation of Yersinia pestis has been reported among rodents and dogs in western Iran, more attention should be paid to disease monitoring in areas with previously reported human cases and in high-risk regions with previous epizootic and enzootic activity.

Plague in Iran: its history and current status.

Science.gov (United States)

Hashemi Shahraki, Abdolrazagh; Carniel, Elizabeth; Mostafavi, Ehsan

2016-01-01

Plague remains a public health concern worldwide, particularly in old foci. Multiple epidemics of this disease have been recorded throughout the history of Iran. Despite the long-standing history of human plague in Iran, it remains difficult to obtain an accurate overview of the history and current status of plague in Iran. In this review, available data and reports on cases and outbreaks of human plague in the past and present in Iran and in neighboring countries were collected, and information was compiled regarding when, where, and how many cases occurred. This paper considers the history of plague in Persia (the predecessor of today's Iran) and has a brief review of plague in countries in the World Health Organization Eastern Mediterranean Region, including a range of countries in the Middle East and North Africa. Since Iran has experienced outbreaks of plague for several centuries, neighboring countries have reported the disease in recent years, the disease can be silent for decades, and the circulation of Yersinia pestis has been reported among rodents and dogs in western Iran, more attention should be paid to disease monitoring in areas with previously reported human cases and in high-risk regions with previous epizootic and enzootic activity.

High-density matter: current status and future challenges

Directory of Open Access Journals (Sweden)

Stone J. R.

2015-01-01

Full Text Available There are many fascinating processes in the Universe which we observe in more and more in detail thanks to increasingly sophisticated technology. One of the most interesting phenomena is the life cycle of stars, their birth, evolution and death. If the stars are massive enough, they end their lives in the core-collapse supernova explosion, the one of the most violent events in the Universe. As the result, the densest objects in the Universe, neutron stars and/or black holes are created. Naturally, the physical basis of these events should be understood in line with observation. The current status of our knowledge of processes in the life of stars is far from adequate for their true understanding. We show that although many models have been constructed their detailed ability to describe observations is limited or non-existent. Furthermore the general failure of all models means that we cannot tell which are heading in the right direction. A possible way forward in modeling of high-density matter is outlined, exemplified by the quark-meson-coupling model (QMC. This model has a natural explanation for the saturation of nuclear forces and depends on very few adjustable parameters, strongly constrained by the underlying physics. Latest QMC results for compact objects and finite nuclei are presented.

Medical telerobotic systems: current status and future trends.

Science.gov (United States)

Avgousti, Sotiris; Christoforou, Eftychios G; Panayides, Andreas S; Voskarides, Sotos; Novales, Cyril; Nouaille, Laurence; Pattichis, Constantinos S; Vieyres, Pierre

2016-08-12

Teleoperated medical robotic systems allow procedures such as surgeries, treatments, and diagnoses to be conducted across short or long distances while utilizing wired and/or wireless communication networks. This study presents a systematic review of the relevant literature between the years 2004 and 2015, focusing on medical teleoperated robotic systems which have witnessed tremendous growth over the examined period. A thorough insight of telerobotics systems discussing design concepts, enabling technologies (namely robotic manipulation, telecommunications, and vision systems), and potential applications in clinical practice is provided, while existing limitations and future trends are also highlighted. A representative paradigm of the short-distance case is the da Vinci Surgical System which is described in order to highlight relevant issues. The long-distance telerobotics concept is exemplified through a case study on diagnostic ultrasound scanning. Moreover, the present review provides a classification into short- and long-distance telerobotic systems, depending on the distance from which they are operated. Telerobotic systems are further categorized with respect to their application field. For the reviewed systems are also examined their engineering characteristics and the employed robotics technology. The current status of the field, its significance, the potential, as well as the challenges that lie ahead are thoroughly discussed.

Current status and future prospects on nuclear industry in Korea

International Nuclear Information System (INIS)

Lee, Joongjae

2006-01-01

It is ny great pleasure to have this chance of speaking at twenty-first KAIF/KNS Annual Conference, with the subject of the current status and future prospects of nuclear industry in Korea. As you all know, since the start of operation in Obninsk, the former Soviet Union, on June 26th, 1954, nuclear generation in the world has expanded continuously for the past 50 years. In 1973, when the first oil crisis hit the world, there were 147 nuclear power plants in operation, supplying only 0.8% of the world energy demand. About 30 years later, by the end of last year, 443 plants were in operation in 32 countries, supplying about 16% of the world power demand. Nuclear power generation is greatly contributing to the energy security of many countries and preservation of global environments. Recently, countries all over the world are becoming aware of the values and importance of nuclear energy which can help respond to energy crises caused by a sharp rise in oil prices and protect the earth from global warming. Due to its high energy density and ability to secure fuel supply at a lower cost, in addition to its cleanliness resulting from almost no emission of greenhouse gases, nuclear power generation is the practical alternative for energy security and the prevention of global warming. However, in the rapidly changing 21st century, the nuclear industries of the world, as well as Korea, are facing more challenges than ever before. The political and social disputes on nuclear generation are continuing while we all are facing urgent challenges, including the concerns about the safety of nuclear generation, procuring site to build nuclear power plants, and the improvement of competitiveness. Please allow me to remind you that it is very important for the world's nuclear societies to cooperate together in order to overcome diverse difficulties along our path and to contribute to the development of mankind and preservation of natural environments with nuclear power as a

Current Status and Open Issues of the 235U Evaluation. Summary Report of an IAEA Consultants’ Meeting

International Nuclear Information System (INIS)

Noguere, Gilles; Trkov, Andrej

2016-08-01

The objective of this consultancy meeting was to discuss the status of the 235 U neutron cross sections from the thermal to MeV energy ranges, to identify the main difficulties and to propose recommendations for improving the current experimental and evaluation works

Spent fuel management: Current status and prospects 1997. Proceedings of a regular advisory group meeting

International Nuclear Information System (INIS)

1998-03-01

Spent fuel management has always been one of the important stages in the nuclear fuel cycle and it is still most vital problems common to all countries with nuclear reactors. It begins with the discharge of spent fuel from a power or a research reactor and ends with its ultimate disposition. Two options exist - an open, once-through cycle with direct disposal of the spent fuel and a closed cycle with reprocessing of the spent fuel, recycling of reprocessed plutonium and uranium in new mixed oxide fuels and disposal of the radioactive waste. Continuous attention is being given by the IAEA to the collection, analysis and exchange of information on spent fuel management. Its role in this area is to provide a forum for exchanging information and to co-ordinate and to encourage closer co-operation among Member States in certain research and development activities that are of common interest. Spent fuel management is recognized as a high priority IAEA activity. The Regular Advisory Group on Spent Fuel Management was established in 1982. The objective of the Regular Advisory Group is to serve as a means of exchanging information on the current status and progress of national programmes on spent fuel management and to provide advice to the IAEA. The results of the last Regular Advisory Group meeting (9-12 September 1997) are reflected in this report. It gives an overview of the status of spent fuel management programmes in a number of countries, a description of the current status and prospects of activities in this field and recommendations of the participants

Radiotherapy of Teikyo University. Second report. Experience and the current status at Itabashi Hospital. Brachytherapy

International Nuclear Information System (INIS)

Ogata, Hitoshi; Yokokawa, Tokuzo; Shirai, Tatsuo; Furui, Shigeru

2005-01-01

To answer the big trend of information disclosure, we are trying to report the experience and the current status of Radiotherapy in Teikyo University. Since 1974, Teikyo University has installed a High-Dose-Rate Remote Afterloading System (HDR RALS) at Itabashi Hospital for brachytherapy. We analyzed the total cases comprehensively in this paper. There were 421 cases treated by Ralstron (Shimazu Co.) between 1974 and 1995 and 128 cases treated additionally between the renewal by Microselectron (Nucletron Co.) and the end of 2002. For several years from the beginning, the number of cases treated by Ralstron had been 30-35 cases annually, but since 1987, the number decreased markedly to fewer than 10 cases per year. After the installation of Microselectron, the number increased gradually to 15 cases per year. Gynecologic tumors accounted for 88.5% of the total cases, namely 96.9% by Ralstron and 60.1% by Microselectron. The others treated by Microselectron were 27 cases with Head and Neck tumors, and 21 cases with digestive tract tumors. To increase the number of the patients for brachytherapy, we should continue to open our current status, and make close relationships between the neighbor hospitals and Teikyo Hospital. (author)

The Dortmund low background facility. Current status and recent developments

Energy Technology Data Exchange (ETDEWEB)

Goessling, Claus; Kroeninger, Kevin; Nitsch, Christian [Experimentelle Physik IV, TU Dortmund, 44221 Dortmund (Germany)

2016-07-01

The Dortmund Low Background Facility (DLB) is a low-background gamma ray spectrometry system with an artificial overburden. The overburden of ten meters of water equivalent, in combination with a multi-layer lead castle and an active muon veto are shielding a high-purity germanium detector of 60 % relative efficiency. The background level is remarkably low compared to a conventional spectrometer system without special shielding and enables sensitivities well below 1 Bq/kg. Thus, material screening measurements as well as environmental monitoring measurements are possible on an easy-accessible location above ground at the campus of the Technische Universitaet Dortmund. The integral background count rate between 40 keV and 2700 keV is 2.528±0.004 counts/kg/min, which is comparable to systems that are situated below ground. In the talk, an overview of the current status of the DLB is given and recent developments are presented.

A study on current status of KAERI's international cooperation programs and strategies for effective implementation

Energy Technology Data Exchange (ETDEWEB)

Kim, Kyoung Pyo; Park, Chun Kab; Noh, In Young; Kim, Young Min

1998-12-01

This is a report on the status and analysis of standard agreement for technical cooperation, expert mission service and technical staff attachment. This report comprises a total of six chapters. Chapter II discusses the status of the technical cooperation agreement which took effect late 1998, and various other model agreements for technical cooperation. Chapter III provides information on the status, regulations, procedures for the expert mission service, and Chapter IV details the current status of the technical staff attachment and the related procedures. Chapter V deals with the utilization status and analysis of the English Counselor, and Chapter VI is the Conclusion. This report has tow objectives. First, we have never published reference books related to standard agreement for technical cooperation, expert mission service and technical staff attachment necessary for international joint research until now. As a result, the research divisions have often asked many questions to the office of international cooperation. Therefore, we expect that many difficulties will be removed and procedures simplified if the research divisions use this report as a reference book. Second, we plan to use this report reference book for policy decisions after establishing the database. (author). 5 tabs., 9 figs.

Symposium on isotope production and applications

International Nuclear Information System (INIS)

1981-01-01

This report contains the papers delivered at the symposium on isotope production and applications, held at Pelindaba, Pretoria, South Africa. The following topics were discussed: facilities for the production of radioisotopes at Pelindaba; the role of the chemist in the development and production of radioisotopic preparations; quality control of radioisotopic products; applications of radioisotopes in medicine; concepts and current status of nuclear imaging; industrial and research applications of radioisotopic tracers and radioisotopic radiation sources; radiation processing using intense radioisotopic radiation sources; a review of current and future radioisotope production activities at the Council for Scientific and Industrial Research

The Majorana Demonstrator for 0νββ: Current Status and Future Plans

Energy Technology Data Exchange (ETDEWEB)

Green, Matthew P. [ORNL; Avignone, F. T. [University of South Carolina/Oak Ridge National Laboratory (ORNL); Bertrand, Jr, Fred E [ORNL; Galindo-Uribarri, Alfredo [ORNL; Radford, David C [ORNL; Romero-Romero, Elisa [ORNL; Varner, Jr, Robert L [ORNL; White, Brandon R [ORNL; Wilkerson, J. F. [UNC/Triangle Univ. Nucl. Lab, Durham, NC/ORNL; Yu, Chang-Hong [ORNL

2015-01-01

The Majorana Demonstrator will search for neutrinoless-double-beta decay (0νββ) in 76Ge, while establishing the feasibility of a future tonne-scale germanium-based 0νββ experiment, and performing searches for new physics beyond the Standard Model. The experiment, currently under construction at the Sanford Underground Research Facility in Lead, SD, will consist of a pair of modular high-purity germanium detector arrays housed inside of a compact copper, lead, and polyethylene shield. Through a combination of strict materials qualifications and assay, low-background design, and powerful background rejection techniques, the Demonstrator aims to achieve a background rate in the 0νββ region of interest (ROI) of no more than 3cnts/(ROI-t-y). The current status of the Demonstrator is discussed, as are plans for its completion.

Current and future benefits from the use of GM technology in food production.

Science.gov (United States)

Engel, K-H; Frenzel, Th; Miller, A

2002-02-28

For the current generation of genetically modified (GM) crops the improvement of agronomic traits (e.g. herbicide tolerance, insect resistance) has been a major objective. The lack of obvious and direct benefits for the consumer has been a main point of criticism. Future trends will increasingly encompass the modification of quality traits, such as the improvement of sensory and especially nutritional properties. Some of the ongoing developments try to meet the desire of consumers for 'healthy' or 'high-tech' foods in developed countries. Others are intended to assist in adjusting the nutritional status of foods to the needs of consumers in developing countries. Considering the increasing world population and the limited amount of arable land, GM technology may also become a valuable tool to ensure food security. The major prerequisite for the applicability of the technique is the safety of the resulting products. The increasing complexity of modifications intended might require adjustments and improvements of the strategies applied to the safety assessment of GM foods. Present research activities try to meet these new challenges.

Lymphoma: current status of clinical and preclinical imaging with radiolabeled antibodies

Energy Technology Data Exchange (ETDEWEB)

England, Christopher G. [University of Wisconsin School of Medicine and Public Health, Department of Medical Physics, Madison, WI (United States); Rui, Lixin [University of Wisconsin School of Medicine and Public Health, Department of Medicine, Madison, WI (United States); University of Wisconsin School of Medicine and Public Health, Carbone Cancer Center, Madison, WI (United States); Cai, Weibo [University of Wisconsin School of Medicine and Public Health, Department of Medical Physics, Madison, WI (United States); University of Wisconsin School of Medicine and Public Health, Carbone Cancer Center, Madison, WI (United States); University of Wisconsin School of Medicine and Public Health, Department of Radiology, Madison, WI (United States)

2017-03-15

Lymphoma is a complex disease that arises from cells of the immune system with an intricate pathology. While lymphoma may be classified as Hodgkin or non-Hodgkin, each type of tumor is genetically and phenotypically different and highly invasive tissue biopsies are the only method to investigate these differences. Noninvasive imaging strategies, such as immunoPET, can provide a vital insight into disease staging, monitoring treatment response in patients, and dose planning in radioimmunotherapy. ImmunoPET imaging with radiolabeled antibody-based tracers may also assist physicians in optimizing treatment strategies and enhancing patient stratification. Currently, there are two common biomarkers for molecular imaging of lymphoma, CD20 and CD30, both of which have been considered for investigation in preclinical imaging studies. In this review, we examine the current status of both preclinical and clinical imaging of lymphoma using radiolabeled antibodies. Additionally, we briefly investigate the role of radiolabeled antibodies in lymphoma therapy. As radiolabeled antibodies play critical roles in both imaging and therapy of lymphoma, the development of novel antibodies and the discovery of new biomarkers may greatly affect lymphoma imaging and therapy in the future. (orig.)

Lymphoma: current status of clinical and preclinical imaging with radiolabeled antibodies

International Nuclear Information System (INIS)

England, Christopher G.; Rui, Lixin; Cai, Weibo

2017-01-01

Lymphoma is a complex disease that arises from cells of the immune system with an intricate pathology. While lymphoma may be classified as Hodgkin or non-Hodgkin, each type of tumor is genetically and phenotypically different and highly invasive tissue biopsies are the only method to investigate these differences. Noninvasive imaging strategies, such as immunoPET, can provide a vital insight into disease staging, monitoring treatment response in patients, and dose planning in radioimmunotherapy. ImmunoPET imaging with radiolabeled antibody-based tracers may also assist physicians in optimizing treatment strategies and enhancing patient stratification. Currently, there are two common biomarkers for molecular imaging of lymphoma, CD20 and CD30, both of which have been considered for investigation in preclinical imaging studies. In this review, we examine the current status of both preclinical and clinical imaging of lymphoma using radiolabeled antibodies. Additionally, we briefly investigate the role of radiolabeled antibodies in lymphoma therapy. As radiolabeled antibodies play critical roles in both imaging and therapy of lymphoma, the development of novel antibodies and the discovery of new biomarkers may greatly affect lymphoma imaging and therapy in the future. (orig.)

The current status of the MASHA setup

Science.gov (United States)

Vedeneev, V. Yu.; Rodin, A. M.; Krupa, L.; Belozerov, A. V.; Chernysheva, E. V.; Dmitriev, S. N.; Gulyaev, A. V.; Gulyaeva, A. V.; Kamas, D.; Kliman, J.; Komarov, A. B.; Motycak, S.; Novoselov, A. S.; Salamatin, V. S.; Stepantsov, S. V.; Podshibyakin, A. V.; Yukhimchuk, S. A.; Granja, C.; Pospisil, S.

2017-11-01

The MASHA setup designed as the mass-separator with the resolving power of about 1700, which allows mass identification of superheavy nuclides is described. The setup uses solid ISOL (Isotope Separation On-Line) method. In the present article the upgrade of some parts of MASHA are described: target box (rotating target + hot catcher), ion source based on electron cyclotron resonance, data acquisition, beam diagnostics and control systems. The upgrade is undertaken in order to increase the total separation efficiency, reduce the separation time, of the installation and working stability and make possible continuous measurements at high beam currents. Ion source efficiency was measured in autonomous regime with using calibrated gas leaks of Kr and Xe injected directly to ion source. Some results of the first experiments for production of radon isotopes using the multi-nucleon transfer reaction 48Ca+242Pu are described in the present article. The using of TIMEPIX detector with MASHA setup for neutron-rich Rn isotopes identification is also described.

The current status of the MASHA setup

International Nuclear Information System (INIS)

Vedeneev, V. Yu.; Rodin, A. M.; Krupa, L.; Belozerov, A. V.; Chernysheva, E. V.; Dmitriev, S. N.; Gulyaev, A. V.; Gulyaeva, A. V.; Kamas, D.; Kliman, J.; Komarov, A. B.; Motycak, S.; Novoselov, A. S.; Salamatin, V. S.; Stepantsov, S. V.; Podshibyakin, A. V.; Yukhimchuk, S. A.; Granja, C.; Pospisil, S.

2017-01-01

The MASHA setup designed as the mass-separator with the resolving power of about 1700, which allows mass identification of superheavy nuclides is described. The setup uses solid ISOL (Isotope Separation On-Line) method. In the present article the upgrade of some parts of MASHA are described: target box (rotating target + hot catcher), ion source based on electron cyclotron resonance, data acquisition, beam diagnostics and control systems. The upgrade is undertaken in order to increase the total separation efficiency, reduce the separation time, of the installation and working stability and make possible continuous measurements at high beam currents. Ion source efficiency was measured in autonomous regime with using calibrated gas leaks of Kr and Xe injected directly to ion source. Some results of the first experiments for production of radon isotopes using the multi-nucleon transfer reaction "4"8Ca+"2"4"2Pu are described in the present article. The using of TIMEPIX detector with MASHA setup for neutron-rich Rn isotopes identification is also described.

The current status of the MASHA setup

Energy Technology Data Exchange (ETDEWEB)

Vedeneev, V. Yu., E-mail: vvedeneyev@gmail.com; Rodin, A. M.; Krupa, L.; Belozerov, A. V.; Chernysheva, E. V.; Dmitriev, S. N.; Gulyaev, A. V.; Gulyaeva, A. V.; Kamas, D. [Joint Institute for Nuclear Research, Flerov Laboratory of Nuclear Reactions (Russian Federation); Kliman, J. [Slovak Academy of Sciences, Institute of Physics (Slovakia); Komarov, A. B.; Motycak, S.; Novoselov, A. S.; Salamatin, V. S.; Stepantsov, S. V.; Podshibyakin, A. V.; Yukhimchuk, S. A. [Joint Institute for Nuclear Research, Flerov Laboratory of Nuclear Reactions (Russian Federation); Granja, C.; Pospisil, S. [Czech Technical University in Prague, Institute of Experimental and Applied Physics (Czech Republic)

2017-11-15

The MASHA setup designed as the mass-separator with the resolving power of about 1700, which allows mass identification of superheavy nuclides is described. The setup uses solid ISOL (Isotope Separation On-Line) method. In the present article the upgrade of some parts of MASHA are described: target box (rotating target + hot catcher), ion source based on electron cyclotron resonance, data acquisition, beam diagnostics and control systems. The upgrade is undertaken in order to increase the total separation efficiency, reduce the separation time, of the installation and working stability and make possible continuous measurements at high beam currents. Ion source efficiency was measured in autonomous regime with using calibrated gas leaks of Kr and Xe injected directly to ion source. Some results of the first experiments for production of radon isotopes using the multi-nucleon transfer reaction {sup 48}Ca+{sup 242}Pu are described in the present article. The using of TIMEPIX detector with MASHA setup for neutron-rich Rn isotopes identification is also described.

Current status and improvement of the nuclear physics experiment course for speciality of nuclear physics and nuclear technology

International Nuclear Information System (INIS)

Qu Guopu; Guo Lanying

1999-01-01

The author reviews the current status of the nuclear physics experiment course for speciality of nuclear physics and nuclear technology in higher education and expresses author's views on the future improvement of the nuclear physics experiment course

Current Status on Biochip and Detection Technology

Energy Technology Data Exchange (ETDEWEB)

Park, Sang Hyun; Gwon, Hui Jeong

2007-06-15

The recent biotechnology technique has been miniaturized and it features a fusion of electricity, electronics and mechanics in the existing biology. As an example, biochip is a collection of miniaturized test sites (microarrays) arranged on a solid substrate that permits many tests to be performed at the same time in order to achieve higher throughput and speed. Like a computer chip that can perform millions of mathematical operations in a second, the biochip can perform thousands of biological reactions, such as decoding genes, in a few seconds. The biochip is being used in toxicological, protein, and biochemical research and it can also be used to rapidly detect chemical agents used in biological warfare so that defensive measures can be taken. These biochip technologies incorporate elements of microfluidics, micromachining, synthetic chemistry, separation technologies, and detection technologies of biological molecules. Basically, biochips can be divided into two types: microarray and lab-on-a-chip system. Microarrays use planted probes to catch and identify target biological molecules while lab-on-a-chips actively process loaded samples. The biochips are becoming more diverse and customers are appearing all over the world. The products from the biochip market are being used to help accelerating the research processes and capabilities of bio-pharmaceutical drug discovery and basic academic bioresearch. To fully take advantages of the attributes of biochip technologies such as miniaturization, parallelism, automation and integration, there are some problems to overcome. The major problem is to reduce the cost. Currently the prices of biochip products are too expensive to replace traditional products and processes. As a method to solve the problem, a radioisotope can be used as a detecting sensor by appling on the biochip, as it were, radio-biochip that will further bring the cost down. The originality using the radioisotope on the biochip technology will be able

Current Status on Biochip and Detection Technology

International Nuclear Information System (INIS)

Park, Sang Hyun; Gwon, Hui Jeong

2007-06-01

The recent biotechnology technique has been miniaturized and it features a fusion of electricity, electronics and mechanics in the existing biology. As an example, biochip is a collection of miniaturized test sites (microarrays) arranged on a solid substrate that permits many tests to be performed at the same time in order to achieve higher throughput and speed. Like a computer chip that can perform millions of mathematical operations in a second, the biochip can perform thousands of biological reactions, such as decoding genes, in a few seconds. The biochip is being used in toxicological, protein, and biochemical research and it can also be used to rapidly detect chemical agents used in biological warfare so that defensive measures can be taken. These biochip technologies incorporate elements of microfluidics, micromachining, synthetic chemistry, separation technologies, and detection technologies of biological molecules. Basically, biochips can be divided into two types: microarray and lab-on-a-chip system. Microarrays use planted probes to catch and identify target biological molecules while lab-on-a-chips actively process loaded samples. The biochips are becoming more diverse and customers are appearing all over the world. The products from the biochip market are being used to help accelerating the research processes and capabilities of bio-pharmaceutical drug discovery and basic academic bioresearch. To fully take advantages of the attributes of biochip technologies such as miniaturization, parallelism, automation and integration, there are some problems to overcome. The major problem is to reduce the cost. Currently the prices of biochip products are too expensive to replace traditional products and processes. As a method to solve the problem, a radioisotope can be used as a detecting sensor by appling on the biochip, as it were, radio-biochip that will further bring the cost down. The originality using the radioisotope on the biochip technology will be able

Current status of fast reactor physics

International Nuclear Information System (INIS)

Hummel, H.H.

1979-01-01

The subject of calculation of reactivity coefficients for fast reactors is developed, starting with a discussion of the status of relevant nuclear data and proceeding to the subjects of group cross section generation and of methods of obtaining reactivity coefficients from group cross sections. Reactivity coefficients measured in critical experiments are compared with calculated values. Dependence of reactivity coefficients on reactor design is discussed. Finally, results of the recent international comparison of calculated reactivity coefficients are presented

Quantum information processing and communication : Strategic report on current status, visions and goals for research in Europe

NARCIS (Netherlands)

Kouwenhoven, L.; Mooij, J.E.

2005-01-01

e present an excerpt of the document “Quantum Information Processing and Communication: Strategic report on current status, visions and goals for research in Europe”, which has been recently published in electronic form at the website of FET (the Future and Emerging Technologies Unit of the

Viewpoints of Nurses about Productivity and the Effects of Current Evaluation Process on it

Directory of Open Access Journals (Sweden)

nahid Dehghan Nayeri

2006-02-01

Findings: Nurses consider productivity both quantitatively (efficiency and qualitatively (effectiveness. But most of them think about productivity from qualitative view. They consider the effective care which they provide to patients. One of the factors facilitating or impeding productivity is evaluation. Effective evaluation can increase productivity, and current barriers impede nursing team productivity from their viewpoint. Conclusion: Effective evaluation can improve productivity. Thus, it is suggested that current evaluation process be revised extensively.

Advanced radiation chemistry research: Current status

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

Radiation chemistry is a branch of chemistry that studies chemical transformations in materials exposed to high-energy radiations. It is based on the use of ionizing radiation as the initiator or catalyst in chemical reactions. The most significant advantage of radiation chemistry lies in its ability to be used in the production and study of almost any reactive atomic and molecular species playing a part in chemical reaction, synthesis, industrial processes, or in biological systems. Over the the last few years a number of meetings have taken place, under the auspices of the IAEA, in order to evaluate recent developments in radiation chemistry as well as the trends indicated by the results obtained. Radiation chemists from different countries have participated at these meetings. The present publication, a companion to the previous publication - New Trends and Development in Radiation Chemistry, IAEA-TECDOC-527 (1989) - includes some of the important contributions presented at these meetings. It is hoped that it will provide a useful overview of current activities and of emerging trends in this field, thus promoting better understanding of potential contributions of radiation chemistry to other fields of knowledge as well as to practical applications in industry, medicine and agriculture. Refs, figs and tabs.

Advanced radiation chemistry research: Current status

International Nuclear Information System (INIS)

1995-10-01

Radiation chemistry is a branch of chemistry that studies chemical transformations in materials exposed to high-energy radiations. It is based on the use of ionizing radiation as the initiator or catalyst in chemical reactions. The most significant advantage of radiation chemistry lies in its ability to be used in the production and study of almost any reactive atomic and molecular species playing a part in chemical reaction, synthesis, industrial processes, or in biological systems. Over the the last few years a number of meetings have taken place, under the auspices of the IAEA, in order to evaluate recent developments in radiation chemistry as well as the trends indicated by the results obtained. Radiation chemists from different countries have participated at these meetings. The present publication, a companion to the previous publication - New Trends and Development in Radiation Chemistry, IAEA-TECDOC-527 (1989) - includes some of the important contributions presented at these meetings. It is hoped that it will provide a useful overview of current activities and of emerging trends in this field, thus promoting better understanding of potential contributions of radiation chemistry to other fields of knowledge as well as to practical applications in industry, medicine and agriculture. Refs, figs and tabs

Current status of the US RERTR Program

International Nuclear Information System (INIS)

Travelli, A.

1982-01-01

This paper describes the status of the RERTR Program. The main objective is to provide the audience with some orientation and sense of perspective that may assist in viewing the other program presentations as part of an overall effort, rather than as separate and unrelated activities

Current status and phenotypic characteristics of Bulgarian poultry genetic resources

International Nuclear Information System (INIS)

Teneva, A.; Gerzilov, V.; Lalev, M.; Lukanov, H.; Mincheva, N.; Oblakova, M.; Petrov, P.; Hristakieva, P.; Dimitrova, I.; Periasamy, K.

2016-01-01

Full text: Poultry biodiversity conservation is a great challenge for many countries. Within the last several years, the number of endangered local breeds has increased, leading to a considerable loss of genetic resources. A similar trend was observed among the poultry breeds, including chicken, local turkey and goose breeds/lines established in Bulgaria, part of which is definitely lost. Currently these breeds/lines are at risk and/or threatened with extinction. The information obtained by phenotypic characterization of these breeds is the first step for planning the management of poultry genetic resources through setting up improved selection schemes and conservation strategies. In this paper, we reviewed the current state of knowledge regarding the morphological and phenotypic diversity of local poultry breeds and some old productive poultry lines in Bulgaria. (author)

The Case of Web-Based Course on Taxation: Current Status, Problems and Future Improvement

Science.gov (United States)

Qin, Zhigang

This paper mainly introduces the case of the web-based course on taxation developed by Xiamen University. We analyze the current status, problems and future improvement of the web-based course. The web-based course has the basic contents and modules, but it has several problems including unclear object, lacking interaction, lacking examination module, lacking study management module, and the learning materials and the navigation are too simple. According to its problems, we put forward the measures to improve it.

Current R and D Status on High-Level Radioactive Waste Disposal in Selected Countries

Energy Technology Data Exchange (ETDEWEB)

Lee, Youn Myoung; Hwang, Yong Soo

2008-11-15

Current R and D status of such countries moving forward as the United States, Sweden, France, Japan and a few other countries for high-level radioactive waste (HLW) disposal in deep geological formation has been reviewed. Even though no HLW repositories have not practically constructed nor operated yet, lots of related R and D are being proceeded in many countries as well as in Korea. Through this brief review further progress is anticipated in this related R and D area in Korea.

The current status and prospect of nuclear power in China

Energy Technology Data Exchange (ETDEWEB)

Wei, S. [State Nuclear Power Technology Corp., Beijing (China)

2014-07-01

'Full text:' China's nuclear power development has attracted world attention. This paper presented the current status of the nuclear power plant in China. By June 30, 2014, China has 20 operational units of 18.05GWe installed capacity, taking up 1.44% of the country's total. All the units have been operating well without any events above INES Level 1 in 2013. China also has 28 units of 30.5GWe installed capacity under construction, which accounts for around 40% of that in the world. The paper presented the progress of AP1000 in China. China made a national plan for 2011 to 2020 with the target to reach 58GWe operational nuclear power and 30GWe under construction by 2020. The Chinese President Xi Jinping urged recently to speed up the approval for new builds. This paper also presented the work of 'Go Global' by Chinese nuclear companies, i.e., their development of international market. (author)

The current status and prospect of nuclear power in China

International Nuclear Information System (INIS)

Wei, S.

2014-01-01

'Full text:' China's nuclear power development has attracted world attention. This paper presented the current status of the nuclear power plant in China. By June 30, 2014, China has 20 operational units of 18.05GWe installed capacity, taking up 1.44% of the country's total. All the units have been operating well without any events above INES Level 1 in 2013. China also has 28 units of 30.5GWe installed capacity under construction, which accounts for around 40% of that in the world. The paper presented the progress of AP1000 in China. China made a national plan for 2011 to 2020 with the target to reach 58GWe operational nuclear power and 30GWe under construction by 2020. The Chinese President Xi Jinping urged recently to speed up the approval for new builds. This paper also presented the work of 'Go Global' by Chinese nuclear companies, i.e., their development of international market. (author)

SPHINX: a generator based on 1 microsecond current rise time LTD stages. Status and first results for production of soft X-ray radiation

International Nuclear Information System (INIS)

Mangeant, Ch.; Roques, B.; Cadiergues, R.

2005-01-01

SPHINX is the new name of the facility developed for soft X-ray production. This facility is based on the ECF2 generator which was designed as a 1-3 MJ, 1 μs rise time, 5-10 MA current driver. We present a detailed view of the technology used for the capacitor bank, for the central vacuum part and for the Z-pinch loads [ru

Genetic Testing of Maturity-Onset Diabetes of the Young Current Status and Future Perspectives

Science.gov (United States)

Firdous, Parveena; Nissar, Kamran; Ali, Sajad; Ganai, Bashir Ahmad; Shabir, Uzma; Hassan, Toyeeba; Masoodi, Shariq Rashid

2018-01-01

Diabetes is a global epidemic problem growing exponentially in Asian countries posing a serious threat. Among diabetes, maturity-onset diabetes of the young (MODY) is a heterogeneous group of monogenic disorders that occurs due to β cell dysfunction. Genetic defects in the pancreatic β-cells result in the decrease of insulin production required for glucose utilization thereby lead to early-onset diabetes (often diabetes and comprises of 1–5% of total diabetes. Till date, 14 genes have been identified and mutation in them may lead to MODY. Different genetic testing methodologies like linkage analysis, restriction fragment length polymorphism, and DNA sequencing are used for the accurate and correct investigation of gene mutations associated with MODY. The next-generation sequencing has emerged as one of the most promising and effective tools to identify novel mutated genes related to MODY. Diagnosis of MODY is mainly relying on the sequential screening of the three marker genes like hepatocyte nuclear factor 1 alpha (HNF1α), hepatocyte nuclear factor 4 alpha (HNF4α), and glucokinase (GCK). Interestingly, MODY patients can be managed by diet alone for many years and may also require minimal doses of sulfonylureas. The primary objective of this article is to provide a review on current status of MODY, its prevalence, genetic testing/diagnosis, possible treatment, and future perspective. PMID:29867778

Physiology and Endocrinology Symposium: The current status of heat shock in early embryonic survival and reproductive efficiency

Science.gov (United States)

The Physiology and Endocrinology Symposium entitled “The Current Status of Heat Shock in Early Embryonic Survival and Reproductive Efficiency” was held at the Joint ADSA-CSAS-AMPA-WSAS-ASAS Meeting in Phoenix, Arizona, July 15 to 19, 2012. In recent years, data has accumulated suggesting a role for...

Current status of nuclear physics research

International Nuclear Information System (INIS)

Bertulani, Carlos A.; Hussein, Mahir S.

2015-01-01

In this review, we discuss the current status of research in nuclear physics which is being carried out in different centers in the world. For this purpose, we supply a short account of the development in the area which evolved over the last nine decades, since the discovery of the neutron. The evolution of the physics of the atomic nucleus went through many stages as more data became available. We briefly discuss models introduced to discern the physics behind the experimental discoveries, such as the shell model, the collective model, the statistical model, the interacting boson model, etc., some of these models may be seemingly in conflict with each other, but this was shown to be only apparent. The richness of the ideas and abundance of theoretical models attests to the important fact that the nucleus is a really singular system in the sense that it evolves from two-body bound states such as the deuteron, to few-body bound states, such as 4 He, 7 Li, 9 Be, etc. and up the ladder to heavier bound nuclei containing up to more than 200 nucleons. Clearly, statistical mechanics, usually employed in systems with very large number of particles, would seemingly not work for such finite systems as the nuclei, neither do other theories which are applicable to condensed matter. The richness of nuclear physics stems from these restrictions. New theories and models are presently being developed. Theories of the structure and reactions of neutron-rich and proton-rich nuclei, called exotic nuclei, halo nuclei, or Borromean nuclei, deal with the wealth of experimental data that became available in the last 35 years. Furthermore, nuclear astrophysics and stellar and Big Bang nucleosynthesis have become a more mature subject. Due to limited space, this review only covers a few selected topics, mainly those with which the authors have worked on. Our aimed potential readers of this review are nuclear physicists and physicists in other areas, as well as graduate students interested

Current status of nuclear physics research

Energy Technology Data Exchange (ETDEWEB)

Bertulani, Carlos A. [Department of Physics and Astronomy, Texas A and M University-Commerce (United States); Hussein, Mahir S., E-mail: hussein@if.usp.br [Instituto Tecnologico de Aeronautica (ITA), Sao Jose dos Campos, SP (Brazil). Dept. de Fisica

2015-12-15

In this review, we discuss the current status of research in nuclear physics which is being carried out in different centers in the world. For this purpose, we supply a short account of the development in the area which evolved over the last nine decades, since the discovery of the neutron. The evolution of the physics of the atomic nucleus went through many stages as more data became available. We briefly discuss models introduced to discern the physics behind the experimental discoveries, such as the shell model, the collective model, the statistical model, the interacting boson model, etc., some of these models may be seemingly in conflict with each other, but this was shown to be only apparent. The richness of the ideas and abundance of theoretical models attests to the important fact that the nucleus is a really singular system in the sense that it evolves from two-body bound states such as the deuteron, to few-body bound states, such as {sup 4}He, {sup 7}Li, {sup 9}Be, etc. and up the ladder to heavier bound nuclei containing up to more than 200 nucleons. Clearly, statistical mechanics, usually employed in systems with very large number of particles, would seemingly not work for such finite systems as the nuclei, neither do other theories which are applicable to condensed matter. The richness of nuclear physics stems from these restrictions. New theories and models are presently being developed. Theories of the structure and reactions of neutron-rich and proton-rich nuclei, called exotic nuclei, halo nuclei, or Borromean nuclei, deal with the wealth of experimental data that became available in the last 35 years. Furthermore, nuclear astrophysics and stellar and Big Bang nucleosynthesis have become a more mature subject. Due to limited space, this review only covers a few selected topics, mainly those with which the authors have worked on. Our aimed potential readers of this review are nuclear physicists and physicists in other areas, as well as graduate

Metabolic engineering of Saccharomyces cerevisiae for production of carboxylic acids : Current status and challenges

NARCIS (Netherlands)

Abbott, D.A.; Zelle, R.M.; Pronk, J.T.; Van Maris, A.J.A.

2009-01-01

To meet the demands of future generations for chemicals and energy and to reduce the environmental footprint of the chemical industry, alternatives for petrochemistry are required. Microbial conversion of renewable feedstocks has a huge potential for cleaner, sustainable industrial production of

Personal dosimetric monitoring in Ukraine: current status and further development

International Nuclear Information System (INIS)

Chumak, V. V.; Musijachenkom, A. V.; Boguslavskaya, A. I.

2003-01-01

Presently Ukraine has mixed system for dosimetric monitoring. Nuclear power plants and some major nuclear facilities have their own dosimetry services, which are responsible for regular dosimetric monitoring of workers. Rest of occupationally exposed persons is monitored by dosimetry laboratories affiliated to the territorial authorities for sanitary and epidemiology supervision. In 2002-2003 Ukrainian Ministry of Health performed survey of the status of dosimetric monitoring and inventory of critical groups requiring such monitoring. Dosimetry services in Ukraine cover about 38,000 occupationally exposed workers, including 9,100 medical professionals, 16,400 employees of 5 nuclear power plants and ca.12,400 workers dealing with other sources of occupational exposure (industry, research). Territorial dosimetry services operate in 13 of 24 regions of Ukraine, using DTU-01 manual TLD readers produced with one exception in 1988-1990. The coverage of critical groups by dosimetric monitoring is variable and ranges from 38% to 100% depending on the region. Personnel of nuclear power plants (about 16,400 workers) is monitored by their own dosimetry services achieving absolute coverage of the main staff and temporary workers. Current inadequate status of dosimetric monitoring infrastructure in Ukraine demands an urgent elaboration of the united state system for monitoring and recording of individual doses. The proposed plan would allows to bring dosimetry infrastructure in Ukraine to the modern state which would be compatible with existing and future European and international radiation protection networks. Unitary structure of Ukraine, strong administrative command and good communications between regions of the country are positive factors in favour of efficient implementation of the proposed plan. Deficiencies are associated with limited funding of this effort. (authors)

Current global status of carotid artery stent placement.

Science.gov (United States)

Wholey, M H; Wholey, M; Bergeron, P; Diethrich, E B; Henry, M; Laborde, J C; Mathias, K; Myla, S; Roubin, G S; Shawl, F; Theron, J G; Yadav, J S; Dorros, G; Guimaraens, J; Higashida, R; Kumar, V; Leon, M; Lim, M; Londero, H; Mesa, J; Ramee, S; Rodriguez, A; Rosenfield, K; Teitelbaum, G; Vozzi, C

1998-05-01

Our purpose was to review the current status of carotid artery stent placement throughout the world. Surveys were sent to major interventional centers in Europe, North and South America, and Asia. Information from peer-reviewed journals was also included and supplemented the survey. The survey asked various questions regarding the patients enrolled, procedure techniques, and results of carotid stenting, including complications and restenosis. Of the centers which were sent surveys, 24 responded. The total number of endovascular carotid stent procedures that have been performed worldwide to date included 2,048 cases, with a technical success of 98.6%. Complications that occurred during carotid stent placement or within a 30-day period following placement were recorded. Overall, there were 63 minor strokes, with a rate of occurrence of 3.08%. The total number of major strokes was 27, for a rate of 1.32%. There were 28 deaths within a 30-day postprocedure period, resulting in a mortality rate of 1.37%. Restenosis rates of carotid stenting have been 4.80% at 6 mo. Endovascular stent treatment of carotid artery atherosclerotic disease is growing as an alternative to vascular surgery, especially for patients that are at high risk for standard carotid endarterectomy. The periprocedural risks for major and minor strokes and death are generally acceptable at this early stage of development.

Review of tantalum and niobium alloy production

International Nuclear Information System (INIS)

Buckman, R.W. Jr.

1984-01-01

This paper concentrates on the current state of niobium- and tantalum-base alloy production. The materials requirements, alloy compositions of interest, and production status are discussed. Finally, a list of developments needed to support the SP-100 program will be identified. A bibliography is included

Current status of the world's research reactors

International Nuclear Information System (INIS)

Dodd, B.

1999-01-01

Data from the IAEA's Research Reactor Database (RRDB) provides information with respect to the status of the world's research reactors. Some summary data are given. Recent initiatives by the IAEA regarding communications and information flow with respect to research reactors are discussed. Future plans and perspectives are also introduced. (author)

Status and prospects of isotope separation industry

International Nuclear Information System (INIS)

Safutin, V.D.; Verbin, Yu.V.; Tolstoj, V.V.

2000-01-01

The stages of the separation industry in the USSR and Russia are demonstrated. The current status of the separation industry and state of the equipment of the isotope separation plants are noted. The developed program for the modernization of the uranium isotope separation involves the production of perspective gas centrifuges, the improvements in the works of gas centrifuge plants and construction materials [ru

Microbial production of hyaluronic acid: current state, challenges, and perspectives

Directory of Open Access Journals (Sweden)

Liu Long

2011-11-01

Full Text Available Abstract Hyaluronic acid (HA is a natural and linear polymer composed of repeating disaccharide units of β-1, 3-N-acetyl glucosamine and β-1, 4-glucuronic acid with a molecular weight up to 6 million Daltons. With excellent viscoelasticity, high moisture retention capacity, and high biocompatibility, HA finds a wide-range of applications in medicine, cosmetics, and nutraceuticals. Traditionally HA was extracted from rooster combs, and now it is mainly produced via streptococcal fermentation. Recently the production of HA via recombinant systems has received increasing interest due to the avoidance of potential toxins. This work summarizes the research history and current commercial market of HA, and then deeply analyzes the current state of microbial production of HA by Streptococcus zooepidemicus and recombinant systems, and finally discusses the challenges facing microbial HA production and proposes several research outlines to meet the challenges.

Comments on the current status and possible future directions of research on heavy-ion interactions near the Coulomb barrier

International Nuclear Information System (INIS)

Satchler, G.R.

1990-01-01

This paper contains comments on the current status and possible future directions of research on heavy-ion interactions near the Coulomb barrier. Fusion reactions, elastic and inelastic scattering and transfer reactions are discussed

Radiation processing in India. Current status and future program

International Nuclear Information System (INIS)

Mittal, Jai Pal

2003-01-01

Radiation processing is an alternative to conventional methods such as thermal and chemical processing in many industrial applications. In India, this technology has found extensive applications in area of healthcare, agriculture, food preservation, industry and environment. Both gamma radiation and electron beam accelerators are being utilized for this purpose. Presently, 6 commercial gamma irradiators housing about 1.5 million curie Co-60 and an annual turnover of over US$ 2 million and 3 commercial electron beam (EB) accelerators with installed capacity of 185 kW are commercially operating in India. Five demonstration plants housing a total of 0.5 million curie Co-60 have been set up to assess the techno-commercial viability of the processes such as radiation vulcanization of natural rubber latex, decontamination of spices, hygienization of sewage sludge, shelf-life extension of onions. The new areas being explored include use of electron beam treated pulp for viscose-rayon process, radiation processed 'hydrogel' burn/wound dressings and radiation processing of natural polymers. In the present paper, the current status of this program, especially the recent developments and future direction of radiation processing technology in India is reviewed. (author)

Management of reprocessed uranium. Current status and future prospects

International Nuclear Information System (INIS)

2007-02-01

There is worldwide interest in developing advanced and innovative technologies for nuclear fuel cycles, minimizing waste and environmental impacts. As of the beginning of 2003, about 171000 tonnes heavy metal spent nuclear fuel is in storage, while smaller amounts have been reprocessed. In several countries, including France, India, Japan and the Russian Federation, spent fuel has been viewed as a national energy resource. Some countries hold reprocessed uranium as the result of their commercial reprocessing service contracts for reprocessing the spent fuel of others. Reprocessed uranium has a potential value for recycling either directly or after appropriate treatment. This report analyses the existing options, approaches and developments in the management of reprocessed uranium. It includes the technical issues involved in managing reprocessed uranium which are RepU arisings, storage, chemical conversion, re-enrichment, fuel fabrication, transport, reactor irradiation, subsequent reprocessing and disposal options, as well as assessment of holistic environmental impacts. The objective of this document is to overview the information on the current status and future trends in the management of RepU and to identify major issues to be considered for future projects

Current status of the UCSF second-generation PACS

Science.gov (United States)

Huang, H. K.; Arenson, Ronald L.; Wong, Albert W. K.; Bazzill, Todd M.; Lou, Shyhliang A.; Andriole, Katherine P.; Wang, Jun; Zhang, Jianguo; Wong, Stephen T. C.

1996-05-01

This paper describes the current status of the second generation PACS at UCSF commenced in October 1992. The UCSF PACS is designed in-house as a hospital-integrated PACS based on an open architecture concept using industrial standards including UNIX operating system, C programming language, X-Window user interface, TCP/IP communication protocol, DICOM 3.0 image standard and HL7 health data format. Other manufacturer's PACS components which conform with these standards can be easily integrated into the system. Relevant data from HIS and RIS is automatically incorporated into the PACS using HL7 data format and TCP/IP communication protocol. The UCSF system also takes advantage of state-of-the-art communication, storage, and software technologies in ATM, multiple storage media, automatic programming, multilevel processes for a better cost-performance system. The primary PACS network is the 155 Mbits/sec OC3 ATM with the Ethernet as the back-up. The UCSF PACS also connects Mt. Zion Hospital and San Francisco VA Medical Center in the San Francisco Bay area via an ATM wide area network with a T1 line as the back-up. Currently, five MR and five CT scanners from multiple sites, two computed radiography systems, two film digitizers, one US PACS module, the hospital HIS and the department RIS have been connected to the PACS network. The image data is managed by a mirrored database (Sybase). The PACS controller, with its 1.3 terabyte optical disk library, acquires 2.5 gigabytes digital data daily. Four 2K, five, 1,600-line multiple monitor display workstations are on line in neuroradiology, pediatric radiology and intensive care units for clinical use. In addition, the PACS supports over 100 Macintosh users in the department and selected hospital sites for both images and textual retrieval through a client/server mechanism. We are also developing a computation and visualization node in the PACS network for advancing radiology research.

Stemless shoulder arthroplasty: current status.

Science.gov (United States)

Churchill, R Sean

2014-09-01

Since the original Neer humeral replacement in the 1950s, the standard primary anatomic total shoulder arthroplasty design has slowly evolved. Most recently, the humeral stem has become progressively shorter to help combat stem-related complications. Currently, there are several companies who have developed and marketed a stemless humeral arthroplasty component. Manufacturers' data for 5 stemless shoulder arthroplasty components currently on the market were analyzed and reviewed. A literature review of short-term results for stemless shoulder arthroplasty was completed. Of the stemless shoulder arthroplasty systems available on the market, 3 are currently undergoing clinical trials in the United States. The Tornier Simpliciti (Tornier, Edina, MN, USA) clinical trial began in 2011. The study with 2-year minimum follow-up results is scheduled for completion in November 2014. The Arthrex Eclipse (Arthrex, Naples, FL, USA) clinical trial was started in January 2013. The tentative study completion date is 2017. The Biomet Nano (Biomet, Warsaw, IN, USA) clinical trial began in October 2013 and also has a tentative completion date of 2017. No other clinical trial is currently under way in the United States. Early results for stemless shoulder arthroplasty indicate clinical results similar to standard stemmed shoulder arthroplasty. Radiographic analysis indicates implant stability without migration or subsidence at 2- to 3-year minimum follow-up.. Several stemless shoulder arthroplasty implants are available outside the United States. Early clinical and radiographic results are promising, but well-designed clinical studies and midterm results are lacking. Three clinical trials are currently under way in the United States with initial availability for use anticipated in 2015. Copyright © 2014 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Mosby, Inc. All rights reserved.

The current status and future plans for the Monte Carlo codes MONK and MCBEND

International Nuclear Information System (INIS)

Smith, N.; Shuttleworth, T.; Grimstone, M.; Hutton, L.; Armishaw, M.; Bird, A.; France, N.; Connolly, S.

2001-01-01

MONK and MCBEND are software tools used for criticality/reactor physics and shielding/dosimetry/general radiation transport applications respectively. The codes are developed by a collaboration comprising AEA Technology and BNFL, and AEA Technology's ANSWERS Software Service supplies them to customers throughout the world on a commercial basis. In keeping with this commercial nature it is vital that the codes' development programmes evolve to meet the diverse expectations of the current and potential customer base. This involves striving to maintain an acceptable balance in the development of the various components that comprise a modern software package. This paper summarises the current status of MONK and MCBEND by indicating how the task of trying to achieve this difficult balance has been addressed in the recent past and is being addressed for the future. (orig.)

Current status of nuclear power generation in Japan and directions in water cooled reactor technology development

International Nuclear Information System (INIS)

Miwa, T.

1991-01-01

Electric power demand aspects and current status of nuclear power generation in Japan are outlined. Although the future plan for nuclear power generation has not been determined yet the Japanese nuclear research centers and institutes are investigating and developing some projects on the next generation of light water reactors and other types of reactors. The paper describes these main activities

Current applications and different approaches for microbial L-asparaginase production

Directory of Open Access Journals (Sweden)

Jorge Javier Muso Cachumba

Full Text Available ABSTRACT L-asparaginase (EC 3.5.1.1 is an enzyme that catalysis mainly the asparagine hydrolysis in L-aspartic acid and ammonium. This enzyme is presented in different organisms, such as microorganisms, vegetal, and some animals, including certain rodent's serum, but not unveiled in humans. It can be used as important chemotherapeutic agent for the treatment of a variety of lymphoproliferative disorders and lymphomas (particularly acute lymphoblastic leukemia (ALL and Hodgkin's lymphoma, and has been a pivotal agent in chemotherapy protocols from around 30 years. Also, other important application is in food industry, by using the properties of this enzyme to reduce acrylamide levels in commercial fried foods, maintaining their characteristics (color, flavor, texture, security, etc. Actually, L-asparaginase catalyzes the hydrolysis of L-asparagine, not allowing the reaction of reducing sugars with this aminoacid for the generation of acrylamide. Currently, production of L-asparaginase is mainly based in biotechnological production by using some bacteria. However, industrial production also needs research work aiming to obtain better production yields, as well as novel process by applying different microorganisms to increase the range of applications of the produced enzyme. Within this context, this mini-review presents L-asparaginase applications, production by different microorganisms and some limitations, current investigations, as well as some challenges to be achieved for profitable industrial production.

Occupational status moderates the association between current perceived stress and high blood pressure: evidence from the IPC cohort study

Science.gov (United States)

Wiernik, Emmanuel; Pannier, Bruno; Czernichow, Sébastien; Nabi, Hermann; Hanon, Olivier; Simon, Tabassome; Simon, Jean-Marc; Thomas, Frédérique; Bean, Kathy; Consoli, Silla; Danchin, Nicolas; Lemogne, Cédric

2013-01-01

Although lay beliefs commonly relate high blood pressure to psychological stress exposure, research findings are conflicting. This study examined the association between current perceived stress and high blood pressure and explored the potential impact of occupational status on this association. Resting blood pressure was measured in 122,816 adults (84,994 men), aged ≥30 years (mean age ± standard deviation: 46.8±9.9 years), without history of cardiovascular and renal disease and not on either psychotropic or antihypertensive drugs. High blood pressure was defined as systolic blood pressure ≥140 mmHg or diastolic blood pressure ≥90 mmHg. Perceived stress in the past month was measured with the 4-item perceived stress scale. A total of 33,154 participants (27.0%) had high blood pressure (151±14/90±9 mmHg). After adjustment for all variables except occupational status, perceived stress was associated with high blood pressure (odds ratio for a 5-point increase: 1.06, 95% confidence interval: [1.03–1.09]). This association was no longer significant after additional adjustment for occupational status (odds ratio: 1.01 [0.99–1.04]). There was a significant interaction (phigh blood pressure among individuals of high occupational status (odds ratio: 0.91, [0.87–0.96]) but positively associated among those of low status (odds ratio: 1.10, [1.03–1.17]) or unemployed (odds ratio: 1.13, [1.03–1.24]). Sensitivity analyses yielded similar results. The association between current perceived stress and blood pressure depends upon occupational status. This interaction may account for previous conflicting results and warrants further studies to explore its underlying mechanisms. PMID:23319539

Anaerobic digestion for bioenergy production: Global status, environmental and techno-economic implications, and government policies.

Science.gov (United States)

Vasco-Correa, Juliana; Khanal, Sami; Manandhar, Ashish; Shah, Ajay

2018-01-01

Anaerobic digestion (AD) is a mature technology that can transform organic matter into a bioenergy source - biogas (composed mainly of methane and carbon dioxide), while stabilizing waste. AD implementation around the world varies significantly, from small-scale household digesters in developing countries to large farm-scale or centralized digesters in developed countries. These differences in the implementation of AD technology are due to a complex set of conditions, including economic and environmental implications of the AD technology, and stimulus provided by a variety of polices and incentives related to agricultural systems, waste management, and renewable energy production. This review explores the current status of the AD technology worldwide and some of the environmental, economic and policy-related drivers that have shaped the implementation of this technology. The findings show that the regulations and incentives have been the primary factor influencing the steady growth of this technology, in both developing and developed countries. Copyright © 2017 Elsevier Ltd. All rights reserved.

Status Report on the Superconducting Dipole Magnet Production for the LHC

CERN Document Server

Bajko, M; Bellesia, B; Fessia, P; Hagen, P; Koutchouk, Jean-Pierre; Miles, J; Modena, M; Pojer,, M; Rossi, L; de Rijk, G; Savary, F; Todesco, E; Tommasini, D; Vlogaert, J; Völlinger, C; Wildner, E

2007-01-01

In August 2006, about 95 % of the production of the 1232 LHC superconducting dipole cold masses, whose coils are wound with Cu/Nb-Ti cables, is completed. One of the 3 manufacturers, having produced one third of the required magnets, completed its production in the end of 2005. The acceptance of the magnets takes place after the 1.9 K performance tests and has been issued for more then 1000 magnets so far. More then half of the dipole magnets are already installed in the tunnel. The paper reviews the main features of the dipoles, the most important steps of the manufacturing and the most critical operations. The quality control and the critical nonconformities that have led, for instance, to a swift campaign of investigations and repairs of few subcomponents (diode assembly, cold bore tube to welding flare fillet weld) are discussed. The status of the production and the performance of the tested dipoles will be presented. Finally the expected schedule for the completion of the production will be shown.

High magnetic field science and its application in the United States current status and future directions

CERN Document Server

National Research Council of the National Academies

2013-01-01

The Committee to Assess the Current Status and Future Direction of High Magnetic Field Science in the United States was convened by the National Research Council in response to a request by the National Science Foundation. This report answers three questions: (1) What is the current state of high-field magnet science, engineering, and technology in the United States, and are there any conspicuous needs to be addressed? (2) What are the current science drivers and which scientific opportunities and challenges can be anticipated over the next ten years? (3) What are the principal existing and planned high magnetic field facilities outside of the United States, what roles have U.S. high field magnet development efforts played in developing those facilities, and what potentials exist for further international collaboration in this area? A magnetic field is produced by an electrical current in a metal coil. This current exerts an expansive force on the coil, and a magnetic field is "high" if it challenges the str...

Neutral strange particle production in antineutrino-neon charged current interactions

Science.gov (United States)

Willocq, S.; Marage, P.; Aderholz, M.; Allport, P.; Baton, J. P.; Berggren, M.; Clayton, E. F.; Cooper-Sarkar, A. M.; Erriquez, O.; Faulkner, P. J. W.; Guy, J.; Hulth, P. O.; Jones, G. T.; Mobayyen, M. M.; Morrison, D. R. O.; Neveu, M.; O'Neale, S.; Sacton, J.; Sansum, R. A.; Varvell, K.; Venus, W.; Wells, J.; Wittek, W.

1992-06-01

Neutral strange particle production inbar v Ne charged current interactions is studied using the bubble chamber BEBC, exposed to the CERN SPS antineutrino wide band beam. From a sample of 1191 neutral strange particles, the inclusive production rates are determined to be (15.7±0.8)% for K 0 mesons, (8.2±0.5)% for Λ, (0.4±0.2)% forbar Λ and (0.6±0.3)% for Σ0 hyperons. The inclusive production properties of K 0 mesons and Λ hyperons are investigated. The Λ hyperons are found to be polarized in the production plane.

Transgenesis and paratransgenesis to control insect-borne diseases: Current status and future challenges

Science.gov (United States)

Coutinho-Abreu, Iliano V.; Zhu, Kun Yan; Ramalho-Ortigao, Marcelo

2009-01-01

Insect-borne diseases cause significant human morbidity and mortality. Current control and preventive methods against vector-borne diseases rely mainly on insecticides. The emergence of insecticide resistance in many disease vectors highlights the necessity to develop new strategies to control these insects. Vector transgenesis and paratransgenesis are novel strategies that aim at reducing insect vectorial capacity, or seek to eliminate transmission of pathogens such as Plasmodium sp., Trypanosoma sp., and Dengue virus currently being developed. Vector transgenesis relies on direct genetic manipulation of disease vectors making them incapable of functioning as vectors of a given pathogen. Paratransgenesis focuses on utilizing genetically modified insect symbionts to express molecules within the vector that are deleterious to pathogens they transmit. Despite the many successes achieved in developing such techniques in the last several years, many significant barriers remain and need to be overcome prior to any of these approaches become a reality. Here, we highlight the current status of these strategies, pointing out advantages and constraints, and also explore issues that need to be resolved before the establishment of transgenesis and paratransgenesis as tools to prevent vector-borne diseases. PMID:19819346

Current status of robotic simulators in acquisition of robotic surgical skills.

Science.gov (United States)

Kumar, Anup; Smith, Roger; Patel, Vipul R

2015-03-01

This article provides an overview of the current status of simulator systems in robotic surgery training curriculum, focusing on available simulators for training, their comparison, new technologies introduced in simulation focusing on concepts of training along with existing challenges and future perspectives of simulator training in robotic surgery. The different virtual reality simulators available in the market like dVSS, dVT, RoSS, ProMIS and SEP have shown face, content and construct validity in robotic skills training for novices outside the operating room. Recently, augmented reality simulators like HoST, Maestro AR and RobotiX Mentor have been introduced in robotic training providing a more realistic operating environment, emphasizing more on procedure-specific robotic training . Further, the Xperience Team Trainer, which provides training to console surgeon and bed-side assistant simultaneously, has been recently introduced to emphasize the importance of teamwork and proper coordination. Simulator training holds an important place in current robotic training curriculum of future robotic surgeons. There is a need for more procedure-specific augmented reality simulator training, utilizing advancements in computing and graphical capabilities for new innovations in simulator technology. Further studies are required to establish its cost-benefit ratio along with concurrent and predictive validity.

Current status of the transient integral fuel element performance code URANUS

International Nuclear Information System (INIS)

Preusser, T.; Lassmann, K.

1983-01-01

To investigate the behavior of fuel pins during normal and off-normal operation, the integral fuel rod code URANUS has been extended to include a transient version. The paper describes the current status of the program system including a presentation of newly developed models for hypothetical accident investigation. The main objective of current development work is to improve the modelling of fuel and clad material behavior during fast transients. URANUS allows detailed analysis of experiments until the onset of strong material transport phenomena. Transient fission gas analysis is carried out due to the coupling with a special version of the LANGZEIT-KURZZEIT-code (KfK). Fuel restructuring and grain growth kinetics models have been improved recently to better characterize pre-experimental steady-state operation; transient models are under development. Extensive verification of the new version has been carried out by comparison with analytical solutions, experimental evidence, and code-to-code evaluation studies. URANUS, with all these improvements, has been successfully applied to difficult fast breeder fuel rod analysis including TOP, LOF, TUCOP, local coolant blockage and specific carbide fuel experiments. Objective of further studies is the description of transient PCMI. It is expected that the results of these developments will contribute significantly to the understanding of fuel element structural behavior during severe transients. (orig.)

Spent fuel management: Current status and prospects

International Nuclear Information System (INIS)

1988-12-01

The main objective of the Advisory Group on Spent Fuel Management is to review the world-wide situation in Spent Fuel Management, to define the most important directions of national efforts and international cooperation in this area, to exchange information on the present status and progress in performing the back-end of Nuclear Fuel Cycle and to elaborate the general recommendations for future Agency programmes in the field of spent fuel management. This report which is a result of the third IAEA Advisory Group Meeting (the first and second were held in 1984 and 1986) is intended to provide the reader with an overview of the status of spent fuel management programmes in a number of leading countries, with a description of the past and present IAEA activities in this field of Nuclear Fuel Cycle and with the Agency's plans for the next years, based on the proposals and recommendations of Member States. A separate abstract was prepared for each of 14 papers presented at the advisory group meeting. Refs, figs and tabs

A study on the continuing education of radiologic technologists: Focused on current status and satisfaction of continuing education

International Nuclear Information System (INIS)

Min, Hye Lim; Choi, In Seok; Nam, So Ra; Kim, Hyun Ji; Yoon, Yong Su; Her, Jae; Han, Seong Gyu; Kim, Jung Min; Ahn, Duck Sun

2014-01-01

In this study, we surveyed the current status, satisfaction and demand of radiologic technologist continuing education for 93 radiologic technologists who participated in the continuing education. To understand the current status and general evaluation and to find out the improvement direction, survey was conducted on 3 categories: participation, satisfaction and demand of continuing education. In addition, we analyzed the continuing education implementation status and the management system by collecting related regulations. As a result, the education completion rates of radiologic technologists from 2010 to 2012 were respectively 42.6%, 43.4% and 34.2%; the rates were similar to other medical technician’s average education completion rates. According to the survey, in case of participation, the most frequent answer was ‘more than five times less than 10 times per year’ with 48.4% and in satisfaction section, the most common answer was ‘Average(3)’ with 34.4%. In demand of continuing education section, 32.8% of the respondents chose ‘Clinical skill training in major field’. In the results of this research, continuing education needs to be managed in the direction of helping radiologists improve their personal ability and self development. Furthermore, to meet the demand of radiologists, the quality of continuing education should be improved to satisfy the educatee

The MAJORANA DEMONSTRATOR for 0νββ: Current Status and Future Plans

Science.gov (United States)

Green, M. P.; Abgrall, N.; Aguayo, E.; Avignone, F. T.; Barabash, A. S.; Bertrand, F. E.; Boswell, M.; Brudanin, V.; Busch, M.; Byram, D.; Caldwell, A. S.; Chan, Y.-D.; Christofferson, C. D.; Combs, D. C.; Cuesta, C.; Detwiler, J. A.; Doe, P. J.; Efremenko, Yu.; Egorov, V.; Ejiri, H.; Elliott, S. R.; Fast, J. E.; Finnerty, P.; Fraenkle, F. M.; Galindo-Uribarri, A.; Giovanetti, G. K.; Goett, J.; Gruszko, J.; Guiseppe, V. E.; Gusev, K.; Hallin, A. L.; Hazama, R.; Hegai, A.; Henning, R.; Hoppe, E. W.; Howard, S.; Howe, M. A.; Keeter, K. J.; Kidd, M. F.; Kochetov, O.; Konovalov, S. I.; Kouzes, R. T.; LaFerriere, B. D.; Leon, J.; Leviner, L. E.; Loach, J. C.; MacMullin, J.; MacMullin, S.; Martin, R. D.; Meijer, S.; Mertens, S.; Nomachi, M.; Orrell, J. L.; O'Shaughnessy, C.; Overman, N. R.; Phillips, D. G.; Poon, A. W. P.; Pushkin, K.; Radford, D. C.; Rager, J.; Rielage, K.; Robertson, R. G. H.; Romero-Romero, E.; Ronquest, M. C.; Schubert, A. G.; Shanks, B.; Shima, T.; Shirchenko, M.; Snavely, K. J.; Snyder, N.; Suriano, A. M.; Thompson, J.; Timkin, V.; Tornow, W.; Trimble, J. E.; Varner, R. L.; Vasilyev, S.; Vetter, K.; Vorren, K.; White, B. R.; Wilkerson, J. F.; Wiseman, C.; Xu, W.; Yakushev, E.; Young, A. R.; Yu, C.-H.; Yumatov, V.

The MAJORANA DEMONSTRATOR will search for neutrinoless-double-beta decay (0νββ) in 76Ge, while establishing the feasibility of a future tonne-scale germanium-based 0νββ experiment, and performing searches for new physics beyond the Standard Model. The experiment, currently under construction at the Sanford Underground Research Facility in Lead, SD, will consist of a pair of modular high-purity germanium detector arrays housed inside of a compact copper, lead, and polyethylene shield. Through a combination of strict materials qualifications and assay, low-background design, and powerful background rejection techniques, the Demonstrator aims to achieve a background rate in the 0νββ region of interest (ROI) of no more than 3 counts in the 0νββ-decay ROI per tonne of target isotope per year (cnts/(ROI-t-y)). The current status of the Demonstrator is discussed, as are plans for its completion.

Current status of cattle production system in Nyagatare District-Rwanda.

Science.gov (United States)

Mazimpaka, Eugene; Mbuza, Francis; Michael, Tukei; Gatari, Eugene N; Bukenya, E M; James, Okwee-Acai

2017-12-01

A study was conducted to characterize the cattle production systems in Nyagatare District, Eastern Province of Rwanda using pre-tested questionnaires, interviews with key informants as well as focus group discussions in a period of 2 months. The respondents were selected by multi-stage sampling at sector and cell levels. Based on the procedure of Krejcie and Morgan (Educational and Psychological Measurement 30:607-610, 1970) to determine the overall sample size, the result indicated that the majority (98.3%) of farms were privately owned by large families of five to seven members, and most farmers (53.9%) had only primary education. Most respondents (52.6%) were in the age bracket of 41-50 years and were mainly (48.3%) located within 3 km from trading centers. The farm size averaged 6.5 ± 0.8 ha and most farms (64.7%) were fenced except in Rukomo Sector (50%) where zero grazing prevailed. Natural pastures (savanna grass land) were the main feed resource; tethering (9%) and communal grazing had diminished. Napier grass was the main planted forage (93.2%), followed by Chloris guyana (3.1%) and Brachiara (1.2%). Leguminous forages were rarely (2.5%) reported. Vita-mineral and salt block supplements, hay, and crop residues were the predominant supplementary feed stuffs used except in Karangazi and Rwemiyaga Sectors where only vita-mineral block predominated. However, maize and rice brans were reported to be the main feed stuffs used in supplementary feeding of lactating cows. Most farmers (89.7%) reported shortage of water as most of the farmers trekked their cattle to the nearest valley dams (59.2%), rivers (21.1%), and a few 6% had water on farms. Indigenous cattle were predominant (67.03%) followed by cross-breeds (28.37%) and exotics (4.6%) while all farmers kept small ruminants. Natural breeding predominated (74.9%) and most farms (60.6%) had animal houses most of which were temporary (52.8%). The reported mean age at first calving (AFC) was highest (40.2�

Status of jatropha cultivation for biodiesel production in Pakistan

International Nuclear Information System (INIS)

Khan, N.A.; Usmani, J.N.

2010-01-01

Pakistan is highly dependent on imported fuels. Sustainable production of biodiesel presents an opportunity to reduce reliance on imported oil, save foreign-exchange reserves, reduce poverty and unemployment, stimulate rural development in areas with acute poverty and enhance access to renewable commercial energy. We are an agriculture-based economy; therefore, production of Bio diesel by utilizing agro-base cultivation will strengthen our agricultural sector and empower the farmers. Moreover, the country has immense potential to attain energy-security through domestic cultivation and processing of bio fuel crops. Some details of the processing plant and manufacturing are also given. This paper describes and delineates the present status of Jatropha cultivation in Pakistan. An attempt is made to project the future of bio diesel, through Jatropha seeds and simultaneous efforts to cultivate other bio diesel- producing seeds to make its cost as low as possible. This paper can also be taken as a base to predict the minimum time required to produce 5-10% replacement of mineral diesel by biodiesel. (author)

Weight status and body image perceptions in adolescents: current perspectives.

Science.gov (United States)

Voelker, Dana K; Reel, Justine J; Greenleaf, Christy

2015-01-01

Adolescence represents a pivotal stage in the development of positive or negative body image. Many influences exist during the teen years including transitions (eg, puberty) that affect one's body shape, weight status, and appearance. Weight status exists along a spectrum between being obese (ie, where one's body weight is in the 95th percentile for age and gender) to being underweight. Salient influences on body image include the media, which can target adolescents, and peers who help shape beliefs about the perceived body ideal. Internalization of and pressures to conform to these socially prescribed body ideals help to explain associations between weight status and body image. The concepts of fat talk and weight-related bullying during adolescence greatly contribute to an overemphasis on body weight and appearance as well as the development of negative body perceptions and dissatisfaction surrounding specific body parts. This article provides an overview of the significance of adolescent development in shaping body image, the relationship between body image and adolescent weight status, and the consequences of having a negative body image during adolescence (ie, disordered eating, eating disorders, and dysfunctional exercise). Practical implications for promoting a healthy weight status and positive body image among adolescents will be discussed.

Storage and treatment of SNF of Alfa class nuclear submarines: current status and problems

International Nuclear Information System (INIS)

Ignatiev, Sviatoslav; Zabudko, Alexey; Pankratov, Dmitry; Somov, Ivan; Suvorov, Gennady

2007-01-01

Available in abstract form only. Full text of publication follows: The current status and main problems associated with storage, defueling and following treatment of spent nuclear fuel (SNF) of Nuclear Submarines (NS) with heavy liquid metal cooled reactors are considered. In the final analysis these solutions could be realized in the form of separate projects to be funded through national and bi- and multilateral funding in the framework of the international collaboration of the Russian Federation on complex utilization of NS and rehabilitation of contaminated objects allocated in the North-West region of Russia. (authors)

Current uses of nanomaterials in biocidal products and treated articles in the EU

DEFF Research Database (Denmark)

Mackevica, Aiga; Revilla Besora, Pau; Brinch, Anna

2016-01-01

Product Regulation (BPR) lays out a list of requirements that manufacturers of biocidal products have to comply with before they can place their products on the market. It is not entirely clear which commercially available articles in the EU have been treated with or incorporate NMs to provide biocidal...... properties to the product. To obtain an insight into what biocidal products are on the EU market, we used The Nanodatabase (nanodb.dk) for analyzing which NMs are being used and what product categories they represent. In this paper, we address the issue of the current uses of NMs in biocidal products...... and discuss how they are currently regulated under the BPR. Even though the BPR already entails nanospecific provisions, correct labelling of biocidal products containing NMs is virtually non-existent. By using The Nanodatabase, it was possible to identify 88 biocidal products containing NMs available...

Sagebrush ecosystems: current status and trends.

Science.gov (United States)

Beever, E.A.; Connelly, J.W.; Knick, S.T.; Schroeder, M.A.; Stiver, S. J.

2004-01-01

The sagebrush (Artemisia spp.) biome has changed since settlement by Europeans. The current distribution, composition and dynamics, and disturbance regimes of sagebrush ecosystems have been altered by interactions among disturbance, land use, and invasion of exotic plants. In this chapter, we present the dominant factors that have influenced habitats across the sagebrush biome. Using a large-scale analysis, we identified regional changes and patterns in “natural disturbance”, invasive exotic species, and influences of land use in sagebrush systems. Number of fires and total area burned has increased since 1980 across much of the sagebrush biome. Juniper (Juniperus spp.) and pinyon (Pinus spp.) woodlands have expanded into sagebrush habitats at higher elevations. Cheatgrass (Bromus tectorum), an exotic annual grass, has invaded much of lower elevation, more xeric sagebrush landscapes across the western portion of the biome. Consequently, synergistic feedbacks between habitats and disturbance (natural and human-caused) have altered disturbance regimes, plant community dynamics and contributed to loss of sagebrush habitats and change in plant communities. Habitat conversion to agriculture has occurred in the highly productive regions of the sagebrush biome and influenced up to 56% of the Conservation Assessment area. Similarly, urban areas, and road, railroad, and powerline networks fragment habitats, facilitate predator movements, and provide corridors for spread of exotic species across the entire sagebrush biome. Livestock grazing has altered sagebrush habitats; the effects of overgrazing combined with drought on plant communities in the late 1880s and early 1900s still influences current habitats. Management of livestock grazing has influenced sagebrush ecosystems by habitat treatments to increase forage and reduce sagebrush and other plant species unpalatable to livestock. Fences, roads, and water developments to manage livestock movements have further

Lower hybrid current drive for edge current density modification in DIII-D: Final status report

International Nuclear Information System (INIS)

Fenstermacher, M.E.; Porkolab, M.

1993-01-01

Application of Lower Hybrid (LH) Current Drive (CD) in the DIII-D tokamak has been studied at LLNL, off and on, for several years. The latest effort began in February 1992 in response to a letter from ASDEX indicating that the 2.45 GHz, 3 MW system there was available to be used on another device. An initial assessment of the possible uses for such a system on DIII-D was made and documented in September 1992. Multiple meetings with GA personnel and members of the LH community nationwide have occurred since that time. The work continued through the submission of the 1995 Field Work Proposals in March 1993 and was then put on hold due to budget limitations. The purpose of this document is to record the status of the work in such a way that it could fairly easily be restarted at a future date. This document will take the form of a collection of Appendices giving both background and the latest results from the FY 1993 work, connected by brief descriptive text. Section 2 will describe the final workshop on LHCD in DIII-D held at GA in February 1993. This was an open meeting with attendees from GA, LLNL, MIT and PPPL. Summary documents from the meeting and subsequent papers describing the results will be included in Appendices. Section 3 will describe the status of work on the use of low frequency (2.45 GHZ) LH power and Parametric Decay Instabilities (PDI) for the special case of high dielectric in the edge regions of the DIII-D plasma. This was one of the critical issues identified at the workshop. Other potential issues for LHCD in the DIII-D scenarios are: (1) damping of the waves on fast ions from neutral beam injection, (2) runaway electrons in the low density edge plasma, (3) the validity of the WKB approximation used in the ray-tracing models in the steep edge density gradients

Pelletized cold moderator of the IBR-2 reactor: current status and future development

International Nuclear Information System (INIS)

Ananiev, V; Beliakov, A; Bulavin, M; Verkhogliadov, A; Kulagin, E; Kulikov, S; Mukhin, K; Shabalin, E; Loktaev, K

2016-01-01

Current status and future development of the pelletized cold moderator of the IBR-2 reactor in Neutron Physics Laboratory of JINR are represented. Nowadays cold moderator works for physical experiments and allows conducting experiments in the region of wavelengths more than 4 Å up to 10-13 times faster in comparison with the warm water moderator. Future development of the pelletized cold moderator is aimed at increasing the time of its operation for experiments and is based on three components: creation of a system of continuous charging and discharging of beads, supplementation of various additives, and use of new materials, such as triphenylmethane. (paper)

Status Epilepticus and Beyond: A Clinical Review of Status Epilepticus and an Update on Current Management Strategies in Super-refractory Status Epilepticus

Directory of Open Access Journals (Sweden)

Roy Poblete

2017-05-01

Full Text Available Status epilepticus and refractory status epilepticus represent some of the most complex conditions encountered in the neurological intensive care unit. Challenges in management are common as treatment options become limited and prolonged hospital courses are accompanied by complications and worsening patient outcomes. Antiepileptic drug treatments have become increasingly complex. Rational polytherapy should consider the pharmacodynamics and kinetics of medications. When seizures cannot be controlled with medical therapy, alternative treatments, including early surgical evaluation can be considered; however, evidence is limited. This review provides a brief overview of status epilepticus, and a recent update on the management of refractory status epilepticus based on evidence from the literature, evidence-based guidelines, and experiences at our institution.

Current status of international training center for nuclear security and security issues in Korea

International Nuclear Information System (INIS)

Lee, Jong-UK; Sin, Byung Woo

2013-01-01