Exploring the Potential for Increased Production from the Wave Energy Converter Lifesaver by Reactive Control

Directory of Open Access Journals (Sweden)

Marta Molinas

2013-07-01

Full Text Available Fred Olsen is currently testing their latest wave energy converter (WEC, Lifesaver, outside of Falmouth Bay in England, preparing it for commercial operation at the Wavehub test site. Previous studies, mostly focusing on hydrodynamics and peak to average power reduction, have shown that this device has potential for increased power extraction using reactive control. This article extends those analyses, adding a detailed model of the all-electric power take-off (PTO system, consisting of a permanent magnet synchronous generator, inverter and DC-link. Time domain simulations are performed to evaluate the PTO capabilities of the modeled WEC. However, when tuned towards reactive control, the generator losses become large, giving a very low overall system efficiency. Optimal control with respect to electrical output power is found to occur with low added mass, and when compared to pure passive loading, a 1% increase in annual energy production is estimated. The main factor reducing the effect of reactive control is found to be the minimum load-force constraint of the device. These results suggest that the Lifesaver has limited potential for increased production by reactive control. This analysis is nevertheless valuable, as it demonstrates how a wave-to-wire model can be used for investigation of PTO potential, annual energy production estimations and evaluations of different control techniques for a given WEC device.

Editorial: Latest methods and advances in biotechnology.

Science.gov (United States)

Lee, Sang Yup; Jungbauer, Alois

2014-01-01

The latest "Biotech Methods and Advances" special issue of Biotechnology Journal continues the BTJ tradition of featuring the latest breakthroughs in biotechnology. The special issue is edited by our Editors-in-Chief, Prof. Sang Yup Lee and Prof. Alois Jungbauer and covers a wide array of topics in biotechnology, including the perennial favorite workhorses of the biotech industry, Chinese hamster ovary (CHO) cell and Escherichia coli. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Recent operating experience during startup testing at latest 1100 MWe BWR-5 nuclear power plants

International Nuclear Information System (INIS)

Tanabe, Akira; Tateishi, Mizuo; Kajikawa, Makoto; Hayase, Yuichi.

1986-01-01

In June and September 1985, the latest two 1100 Mwe BWR-5 nuclear power plants started commercial operation about ten days earlier than initially expected without any unscheduled shutdown. These latest plants, 2F-3 and K-1, are characterized by an improved core with new 8 x 8 fuel assemblies, highly reliable control systems, advanced control room system and turbine steam full bypass system for full load rejection (2F3). This paper describes the following operating experiences gained during their startup testing. 1) Continuous operation at full load rejection. 2) Stable operation at natural circulating flow condition. 3) 31 and 23 hour short time start up operation. 4) 100-75-100 %, 1-8-1-14 hours daily load following operation. (author)

High sedimentation rates in the Early Triassic after latest Permian mass extinction: Carbonate production is main factor in non-Arctic regions

Science.gov (United States)

Horacek, Micha; Brandner, Rainer

2016-04-01

A substantial change in sedimentation rates towards higher values has been documented from the Late Permian to the Lower Triassic. Although it is assumed and also has been shown that the deposition of siliciclastic material increased in the Lower Triassic due to stronger erosion because of loss of land cover and increased chemical and physical weathering with extreme climate warming, the main sediment production occurred by marine carbonate production. Still, carbonate production might have been significantly influenced by weathering and erosion in the hinterland, as the transport of dust by storms into the ocean water probably was a main nutrient source for microbial carbonate producers, because "normal" nutrient supply by ocean circulation, i. e. upwelling was strongly reduced due to the elevated temperatures resulting in water-column stratification . Sediment accumulation was also clearly influenced by the paleo-geographic and latitudinal position, with lower carbonate production and sedimentation rates in moderate latitudes. The existence of a "boundary clay" and microbial carbonate mounds and layers in the immediate aftermath of the latest Permian mass extinction points towards a development from a short-timed acid ocean water - resulting in a carbonate production gap and the deposition of the boundary clay towards the deposition of the microbial mounds and layers due to the microbial production of micro-environments with higher alkalinity allowing the production of carbonate. After the return of the ocean water to normal alkalinity planktic production of carbonate resulted in a very high sedimentation rate, especially taking into account the absence of carbonate producing eukaryotic algae and animals.

Latest results from EXO-200

International Nuclear Information System (INIS)

TOSI, D.

2014-01-01

The Enriched Xenon Observatory (EXO) is an experimental program searching for neutrino-less double beta decay in xenon-136. The first stage of this program, EXO-200, has been in operation since early 2011. I present here the latest physics results from the experiment.

Latest nuclear monitoring instrumentation and control system and its planned application

International Nuclear Information System (INIS)

Kawakami, Seishiro; Sato, Toshifumi; Ikeda, Jun

2002-01-01

With the recent rapid progress made in electronic devices used in digital monitoring and control systems, Toshiba has developed special-purpose digital monitoring equipment and human-machine interface equipment that meet the special requirement of high reliability and long-term supply and maintainability for nuclear power plants, and is scheduled to apply these new products to actual nuclear power plants. Moreover, for the in-core sensor, which is a special-purpose product for nuclear power plants, Toshiba has been developing a new local power range monitor (LPRM) detector as the comprehensive result of improvements made up to now, and has developed the first domestic gamma-thermo (GT) detector as a pivot of the next-generation neutron monitoring system. (author)

Customizing graphical user interface technology for spacecraft control centers

Science.gov (United States)

Beach, Edward; Giancola, Peter; Gibson, Steven; Mahmot, Ronald

1993-01-01

The Transportable Payload Operations Control Center (TPOCC) project is applying the latest in graphical user interface technology to the spacecraft control center environment. This project of the Mission Operations Division's (MOD) Control Center Systems Branch (CCSB) at NASA Goddard Space Flight Center (GSFC) has developed an architecture for control centers which makes use of a distributed processing approach and the latest in Unix workstation technology. The TPOCC project is committed to following industry standards and using commercial off-the-shelf (COTS) hardware and software components wherever possible to reduce development costs and to improve operational support. TPOCC's most successful use of commercial software products and standards has been in the development of its graphical user interface. This paper describes TPOCC's successful use and customization of four separate layers of commercial software products to create a flexible and powerful user interface that is uniquely suited to spacecraft monitoring and control.

The latest technical solutions in rail vehicles drives

Directory of Open Access Journals (Sweden)

Andrzejewski Maciej

2017-01-01

Full Text Available The article discusses the latest trends and solutions used in the offers of rail vehicles manufacturers. The study is mainly concerned with the technical solutions used in hybrid rail vehicles, whose development has become one of the priorities for the development of rail vehicles in the European Union in recent years. Stricter emissions standards for harmful compounds in the European Union have forced manufacturers to use increasingly sophisticated technology, including hybrid drives and alternative fuels. The products and solutions offered by the major manufacturers on the market, along with their capabilities and future applications are described. The predicted trends in the development of propulsion technology for rail and road-rail vehicles are also indicated in view of the current legislative aspirations among the EU Member States.

Design, product structuring and modelling of mechatronic products and systems

DEFF Research Database (Denmark)

Conrad, Finn; Sørensen, Torben

2003-01-01

Information Technology offers software and hardware for improvement of the engineering design, structuring and control systems, and industrial applications. The latest progress in IT makes integration of an overall design and manufacturing IT- concept feasible and commercially attractive. An IT......-tool concept for modelling, simulation and design of mechatronic products and systems is proposed in this paper. It built on results from a Danish mechatronic research program on intelligent motion control as well as from the Esprit project SWING on IT-tools for rapid prototyping of fluid power components...

The latest results on top quark pair cross-section measurement

CERN Document Server

Yamauchi, Katsuya; The ATLAS collaboration

2015-01-01

The latest results on top quark pair production cross-section measurement in proton-proton collisions at $\\sqrt{s} = 7\\ TeV$ and $\\sqrt{s} = 8\\ TeV$ with the ATLAS detector are reported. The inclusive cross-section was measured with 4% of uncertainty using di-lepton e-mu events. The measurement of the differential cross-section as functions of various observables such as transverse momentum and rapidity of the top quark and invariant mass of the pseudo-top-quark pair system including the results in boosted topologies are also reported. These results are compared with the various generators such as Powheg, Alpgen and MC@NLO and the various PDF sets.

Interaction between production control and quality control

NARCIS (Netherlands)

Bij, van der J.D.; Ekert, van J.H.W.

1999-01-01

Describes a qualitative study on interaction between systems for production control and quality control within industrial organisations. Production control and quality control interact in a sense. Good performance for one aspect often influences or frustrates the performance of the other. As far as

Latest developments in on- and off-line inspection of bank notes during production

Science.gov (United States)

Brown, Stephen C.

2004-06-01

The inspection of bank notes is a highly labour intensive process where traditionally every note on every sheet is inspected manually. However with the advent of more and more sophisticated security features, both visible and invisible, and the requirement of cost reduction in the printing process, it is clear that automation is required. Machines for the automatic inspection of bank notes have been on the market for the past 10 to 12 years, but recent developments in technology have enabled a new generation of detectors and machines to be developed. This paper focuses on the latest developments in both the off-line and on-line inspection of bank notes covering not only the visible spectrum but also a new range of detectors for inspection some of the more common invisible features used as covert features in today's bank notes.

Latest results on Z boson production from LHCb

CERN Multimedia

CERN. Geneva

2013-01-01

Recent measurements of Z boson production using data collected at a center-of-mass energy of 7 TeV by the LHCb experiment are presented. These measurements test QCD and electroweak theory and can provide constraints on the proton parton distribution functions. Inclusive and differential cross-section measurements for Z bosons, decaying into di-muon, di-electron, and di-tau final states, and a measurement of the production of jets of particles in association with a Z boson are presented. The results are found to be in agreement with theoretical predictions with recently calculated parton distribution functions.

The latest general chemistry

International Nuclear Information System (INIS)

Ryu, Geun Bae; Choi, Se Yeong; Kim, Chin Yeong; Yoon, Gil Jung; Lee, Eun Seok; Seo, Moon Gyu

1995-02-01

This book deals with the latest general chemistry, which is comprised of twenty-three chapters, the contents of this book are introduction, theory of atoms and molecule, chemical formula and a chemical reaction formula, structure of atoms, nature of atoms and the periodic table, structure of molecule and spectrum, gas, solution, solid, chemical combination, chemical reaction speed, chemical equilibrium, thermal chemistry, oxidation-reduction, electrochemistry, acid-base, complex, aquatic chemistry, air chemistry, nuclear chemistry, metal and nonmetal, organic chemistry and biochemistry. It has exercise in the end of each chapter.

The latest Light Robotics breakthroughs - Postdeadline

DEFF Research Database (Denmark)

Glückstad, Jesper; Palima, Darwin; Bañas, Andrew

Contemporary nanoscopy provides functionalities, not only for observing life science on the smallest scales but also for actively reaching into and manipulating at subcellular levels. This post-deadline contribution describes the latest generation of 3D-printed micro-tools for enabling light-acti......-activated robotics on sub-diffraction scales: Light Robotics....

Latest Surprises from Mira the Wonderful

Science.gov (United States)

Karovska, Margarita; Marengo, Massimo; Wood, Brian

We report the latest results from our long-term study of Mira A and its companion Mira B. These include a study of the dust environment in mid-IR wavelengths (Marengo et al. 2001), and of the accretion processes in the Mira AB interacting system (Wood, Karovska, and Raymond 2002).

Glaucoma: Symptoms, Diagnosis, Treatment and Latest Research

Science.gov (United States)

... of this page please turn Javascript on. Feature: Glaucoma Glaucoma: Symptoms, Diagnosis, Treatment and Latest Research Past Issues / Fall 2009 Table of Contents Symptoms and Diagnosis Glaucoma can develop in one or both eyes. Often ...

PLMPC - supervisor predictive control; PLMPC - controle supervisorio preditivo

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Amalia Burger Santa Brigida; Matuck, Fuad Jorge [White Martins S.A., Rio de Janeiro, RJ (Brazil)

2010-07-01

MPC is the latest and most sophisticated technology for controlling chemical plants with several interactive variables. Since 1984, over 2000 MPC systems have been installed worldwide, mostly at oil refineries and large petrochemical facilities. Praxair was the first company to apply MPC technology to the air separation industry. MPC technology is now Praxair's standard platform for supervisory control of cryogenic air separation plants. Most new Praxair plants are controlled by MPC systems. The Pipeline MPC (PLMPC) drives at least 2 plants, A and B, GO2 production towards optimum targets during the pipeline variations. The purpose of the PLMPC is to optimize gas oxygen (GO2) production according to demand, while ensuring a quickly pipeline response. It is implemented using AspenTech DMCPlus software, which is configured with a model file and a controller configuration file, that executes periodically. (author)

Latest ATLAS results on $\\phi_s$

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00222462; The ATLAS collaboration

2017-01-01

New Physics effects beyond the predictions of the Standard Model may manifest in the $CP$-violation of $b$-hadron decays. This paper presents the latest analysis of $B^0_s \\to J/\\psi\\phi$ decay at the ATLAS experiment, measuring the $CP$-violating phase $\\phi_s$, the decay width $\\Gamma_s$ and the difference of widths between the mass eigenstates $\\Delta\\Gamma_s$. The latest results are using integrated luminosity of 14.3 fb$^{-1}$ collected by the ATLAS detector from $\\sqrt{s}$ = 8 TeV $pp$ collisions at the Large Hadron Collider, and are statistically combined with the results from 4.9 fb$^{-1}$ of $\\sqrt{s}$ = 7 TeV data, leading to: \\begin{eqnarray*} \\phi_s & = & -0.090 \\pm 0.078 \\;\\mathrm{(stat.)} \\pm 0.041 \\;\\mathrm{(syst.)~rad} ,\\;\\;\\\\ \\Delta\\Gamma_s & = & 0.085 \\pm 0.011 \\;\\mathrm{(stat.)} \\pm 0.007 \\;\\mathrm{(syst.)~ps}^{-1} ,\\;\\;\\\\ \\Gamma_s & = & 0.675 \\pm 0.003 \\;\\mathrm{(stat.)} \\pm 0.003 \\;\\mathrm{(syst.)~ps}^{-1}. \\end{eqnarray*} The results are also presented in the form...

Technical highlights of the latest upgrades to Hitachi's G-HIACS νSAFE functional safety controller

International Nuclear Information System (INIS)

Tan, D.; Ishii, K.; Otsuka, Y.; Uemura, K.; Suenaga, M.; Koyamada, T.

2014-01-01

Hitachi has developed the G-HIACS νSAFE (pronounced 'nu-safe'), a Functional Safety (FS) controller compliant to IEC 61508 SIL 2, in part to satisfy the requirements of control systems for Nuclear Steam Plants (NSP). Hitachi has reported some of the main challenges, counter-measures and improvements encountered and designed during the several phases of development of controller system at previous Canadian Nuclear Society (CNS) Annual Conferences. Hitachi received initial Product Version 1 (PV1) certification from TUV Rheinland in 2010. Since then, additional functional and design improvements and changes have made product re-certification necessary, in order to cover the scope of the additional and improved capabilities. This paper describes some of these Product Version 2 (PV2) capabilities (certified by TUV Rheinland in 2013). (author)

2nd International Conference on Mechatronics and Automatic Control

CERN Document Server

2015-01-01

This book examines mechatronics and automatic control systems. The book covers important emerging topics in signal processing, control theory, sensors, mechanic manufacturing systems and automation. The book presents papers from the second International Conference on Mechatronics and Automatic Control Systems held in Beijing, China on September 20-21, 2014. Examines how to improve productivity through the latest advanced technologies Covering new systems and techniques in the broad field of mechatronics and automatic control systems.

The latest electrical installation (I)

International Nuclear Information System (INIS)

Won, Jong Su

1976-04-01

This book deals with the latest electrical installation. The contents of this book are construction electrical installation, regulations related electrical installation, foundation and principle of wiring, main line feeder, lighting installation, power of wiring, main line feeder, lighting installation, power installation, method to read structure drawing for electrical construct drawing electric lamp wiring diagram, working drawing, material and tools and method of construction of electrical installation on types of wiring construction, metallic conduit, rigid poly-vinyl conduit wiring, bus duct work, cable work and insulation out of metal lathed.

Latest Proterozoic stratigraphy and earth history

Science.gov (United States)

Knoll, Andrew H.; Walter, Malcolm R.

1992-01-01

Novel biostratigraphic and chemostratigraphic data furnish an improved framework for stratigraphic correlation of the Proterozoic Eon as well as tools for a chronostratigraphic division of the late Proterozoic. It is argued that, in conjunction with geochronometric data, protistan microfossils and isotope geochemistry can furnish a means for an eventual integration of the latest Proterozoic Eon. Attention is given to the emerging methodologies of fossil protists and prokaryotes and of isotopic chemostratigraphy.

The latest development of EAST neutral beam injector

International Nuclear Information System (INIS)

Hu Chundong; Xu Yongjian

2014-01-01

As the first full superconducting non-circular cross section Tokomak in the world, EAST is used to explore the forefront physics and engineering issues on the construction of Tokomak fusion reactor. Neutral beam injection has been recognized as one of the most effective means for plasma heating. According to the research plan of the EAST physics experiment, a set of neutral beam injector (4∼8 MW, 10∼100 s)will be built and operational in 2014. The paper presents the latest development of EAST neutral beam injector and the latest experiment results of long pulse beam extraction and high power beam extraction are reported, those results show that all targets reach or almost reach the design targets. All these will lay a solid foundation for the achievement of plasma heating and current drive for EAST in 2014. (authors)

Network-based production quality control

Science.gov (United States)

Kwon, Yongjin; Tseng, Bill; Chiou, Richard

2007-09-01

This study investigates the feasibility of remote quality control using a host of advanced automation equipment with Internet accessibility. Recent emphasis on product quality and reduction of waste stems from the dynamic, globalized and customer-driven market, which brings opportunities and threats to companies, depending on the response speed and production strategies. The current trends in industry also include a wide spread of distributed manufacturing systems, where design, production, and management facilities are geographically dispersed. This situation mandates not only the accessibility to remotely located production equipment for monitoring and control, but efficient means of responding to changing environment to counter process variations and diverse customer demands. To compete under such an environment, companies are striving to achieve 100%, sensor-based, automated inspection for zero-defect manufacturing. In this study, the Internet-based quality control scheme is referred to as "E-Quality for Manufacturing" or "EQM" for short. By its definition, EQM refers to a holistic approach to design and to embed efficient quality control functions in the context of network integrated manufacturing systems. Such system let designers located far away from the production facility to monitor, control and adjust the quality inspection processes as production design evolves.

Robust Manufacturing Control

CERN Document Server

2013-01-01

This contributed volume collects research papers, presented at the CIRP Sponsored Conference Robust Manufacturing Control: Innovative and Interdisciplinary Approaches for Global Networks (RoMaC 2012, Jacobs University, Bremen, Germany, June 18th-20th 2012). These research papers present the latest developments and new ideas focusing on robust manufacturing control for global networks. Today, Global Production Networks (i.e. the nexus of interconnected material and information flows through which products and services are manufactured, assembled and distributed) are confronted with and expected to adapt to: sudden and unpredictable large-scale changes of important parameters which are occurring more and more frequently, event propagation in networks with high degree of interconnectivity which leads to unforeseen fluctuations, and non-equilibrium states which increasingly characterize daily business. These multi-scale changes deeply influence logistic target achievement and call for robust planning and control ...

Development of Production Control in Small Batch Production

Directory of Open Access Journals (Sweden)

Németh Péter

2016-01-01

Full Text Available Our aim with this paper is to develop a new performance measurement and control system for small batch production in the automotive industry. For this reason, we present our previous research results for warehouse performance measurement and adopt its methodology to production control. The proposed method is based on artificial intelligence (neural networks.

Latest design of gate valves

Energy Technology Data Exchange (ETDEWEB)

Kurzhofer, U.; Stolte, J.; Weyand, M.

1996-12-01

Babcock Sempell, one of the most important valve manufacturers in Europe, has delivered valves for the nuclear power industry since the beginning of the peaceful application of nuclear power in the 1960s. The latest innovation by Babcock Sempell is a gate valve that meets all recent technical requirements of the nuclear power technology. At the moment in the United States, Germany, Sweden, and many other countries, motor-operated gate and globe valves are judged very critically. Besides the absolute control of the so-called {open_quotes}trip failure,{close_quotes} the integrity of all valve parts submitted to operational forces must be maintained. In case of failure of the limit and torque switches, all valve designs have been tested with respect to the quality of guidance of the gate. The guidances (i.e., guides) shall avoid a tilting of the gate during the closing procedure. The gate valve newly designed by Babcock Sempell fulfills all these characteristic criteria. In addition, the valve has cobalt-free seat hardfacing, the suitability of which has been proven by friction tests as well as full-scale blowdown tests at the GAP of Siemens in Karlstein, West Germany. Babcock Sempell was to deliver more than 30 gate valves of this type for 5 Swedish nuclear power stations by autumn 1995. In the presentation, the author will report on the testing performed, qualifications, and sizing criteria which led to the new technical design.

Latest results from LUNA

Science.gov (United States)

Depalo, Rosanna; LUNA Collaboration

2018-01-01

A precise knowledge of the cross section of nuclear fusion reactions is a crucial ingredient in understanding stellar evolution and nucleosynthesis. At stellar temperatures, fusion cross sections are extremely small and difficult to measure. Measuring nuclear cross sections at astrophysical energies is a challenge that triggered a huge amount of experimental work. A breakthrough in this direction was the first operation of an underground accelerator at the Laboratory for Underground Nuclear Astrophysics (LUNA) in Gran Sasso, Italy. The 1400 meters of rocks above the laboratory act as a natural shield against cosmic radiation, suppressing the background by orders of magnitude. The latest results achieved at LUNA are discussed, with special emphasis on the 22Ne(p,γ)23Na reaction. Future perspectives of the LUNA experiment are also illustrated.

The latest succession of dinosaur tracksites in Europe: Hadrosaur ichnology, track production and palaeoenvironments.

Directory of Open Access Journals (Sweden)

Bernat Vila

Full Text Available A comprehensive review and study of the rich dinosaur track record of the Tremp Formation in the southern Pyrenees of Spain (Southwestern Europe shows a unique succession of footprint localities prior to the end-Cretaceous mass extinction event. A description of some 30 new tracksites and data on sedimentary environments, track occurrence and preservation, ichnology and chronostratigraphy are provided. These new track localities represent various facies types within a diverse set of fluvial environments. The footprint discoveries mostly represent hadrosaurian and, less abundantly, to sauropod dinosaurs. The hadrosaur tracks are significantly smaller in size than, but morphologically similar to, those of North America and Asia and are attributable to the ichnogenus Hadrosauropodus. The track succession, with more than 40 distinct track levels, indicates that hadrosaur footprints in the Ibero-Armorican region occur predominantly in the late Maaastrichtian (at least above the early Maastrichtian-late Maastrichtian boundary. The highest abundance is found noticeably found in the late Maastrichtian, with tracks occurring in the C29r magnetochron, within about the latest 300,000 years of the Cretaceous.

Radiation field control at the latest BWR plants -- design principle, operational experience and future subjects

Energy Technology Data Exchange (ETDEWEB)

Uchida, Shunsuke [Energy Research Lab., Ibaraki (Japan); Ohsumi, Katsumi; Takashima, Yoshie [Hitachi Works, Ibaraki (Japan)

1995-03-01

Improvements of operational procedures to control water chemistry, e.g., nickel/iron control, as well as application of hardware improvements for reducing radioactive corrosion products resulted in an extremely low occupational exposure of less than 0.5 man.Sv/yr without any serious impact on the radwaste system, for BWR plants involved in the Japanese Improvement and Standardization Program. Recently, {sup 60}C radioactively in the reactor water has been increasing due to less crud fixation on the two smooth surfaces of new type high performance fuels and to the pH drop caused by chromium oxide anions released from stainless steel structures and pipings. This increase must be limited by changes in water chemistry, e.g., applications of modified nickel/iron ratio control and weak alkali control. Controlled water chemistry to optimize three points, the plant radiation level and integrities of fuel and structural materials, is the primary future subject for BWR water chemistry.

Related regulation of quality control of industrial products

International Nuclear Information System (INIS)

1983-04-01

This book introduce related regulation of quality control of industrial products, which includes regulations of industrial products quality control, enforcement ordinance of industrial products quality control, enforcement regulation of quality control of industrial products, designated items with industrial production quality indication, industrial production quality test, and industrial production quality test organization and management tips of factory quality by grade.

Association between product quality control and process quality control of bulk milk

NARCIS (Netherlands)

Velthuis, A.; Asseldonk, van M.A.P.M.

2010-01-01

Assessment of dairy-milk quality is based on product quality control (testing bulk-milk samples) and process quality control (auditing dairy farms). It is unknown whether process control improves product quality. To quantify possible association between product control and process control a

Latest Results of Open Heavy Flavor and Quarkonia from the PHENIX Experiment at RHIC

International Nuclear Information System (INIS)

Nouicer, Rachid

2017-01-01

The PHENIX Collaboration carries out a comprehensive physics program which studies heavy flavor production in relativistic heavy ion collisions at RHIC. The discovery at RHIC of large high-p T suppression and flow of electrons from heavy quarks flavors have altered our view of the hot and dense matter formed in central Au+Au collisions at GeV. These results suggest a large energy loss and flow of heavy quarks in the hot, dense matter. In recent years, the PHENIX has installed a silicon vertex tracker both in central rapidity (VTX) and in forward rapidity (FVTX) regions, and has collected large data samples. These two silicon trackers enhance the capability of heavy flavor measurements via precision tracking. This paper summarizes some of the latest PHENIX results concerning open heavy flavor and quarkonia production as a function of rapidity, energy and system size. (paper)

Latest German-English Terminology in CADCAM and Robotics

International Nuclear Information System (INIS)

Hussain, S M

2014-01-01

As a technical translator who speaks German fluently, the author would like to study and display the latest bilingual technical terminology in German being used in hardware, software and process technology involved in CADCAM and ROBOTICS. This will greatly help technical translators to correctly translate difficult texts from this area of technology

The DAFT/FADA Survey status and latest results

Science.gov (United States)

Guennou, L.

2011-12-01

We present here the latest results obtained from the American French collaboration called the Dark energy American French Team/French American DArk energy Team (DAFT/FADA). The goal of the DAFT/FADA collaboration is to carry out a weak lensing tomography survey of z = 0.4-0.9 rich clusters of galaxies. Unlike supernovae or other methods such as cluster of galaxy counts, weak lensing tomography is purely based on geometry and does not depend on knowledge of the physics of the objects used as distance indicators. In addition, the reason for analyzing observations in the direction of clusters is that the shear signal is enhanced by about 10 over the field. Our work will eventually contain results obtained on 91 rich clusters from the HST archive combined with ground based work to obtain photo-zs. This combination of photo-z and weak lensing tomography will enable us to constrain the equation of state of dark energy. We present here the latest results obtained so far in this study.

Multifaceted bench comparative evaluation of latest intensive care unit ventilators.

Science.gov (United States)

Garnier, M; Quesnel, C; Fulgencio, J-P; Degrain, M; Carteaux, G; Bonnet, F; Similowski, T; Demoule, A

2015-07-01

Independent bench studies using specific ventilation scenarios allow testing of the performance of ventilators in conditions similar to clinical settings. The aims of this study were to determine the accuracy of the latest generation ventilators to deliver chosen parameters in various typical conditions and to provide clinicians with a comprehensive report on their performance. Thirteen modern intensive care unit ventilators were evaluated on the ASL5000 test lung with and without leakage for: (i) accuracy to deliver exact tidal volume (VT) and PEEP in assist-control ventilation (ACV); (ii) performance of trigger and pressurization in pressure support ventilation (PSV); and (iii) quality of non-invasive ventilation algorithms. In ACV, only six ventilators delivered an accurate VT and nine an accurate PEEP. Eleven devices failed to compensate VT and four the PEEP in leakage conditions. Inspiratory delays differed significantly among ventilators in invasive PSV (range 75-149 ms, P=0.03) and non-invasive PSV (range 78-165 ms, Pventilation algorithms efficiently prevented the decrease in pressurization capacities and PEEP levels induced by leaks in, respectively, 10 and 12 out of the 13 ventilators. We observed real heterogeneity of performance amongst the latest generation of intensive care unit ventilators. Although non-invasive ventilation algorithms appear to maintain adequate pressurization efficiently in the case of leakage, basic functions, such as delivered VT in ACV and pressurization in PSV, are often less reliable than the values displayed by the device suggest. © The Author 2015. Published by Oxford University Press on behalf of the British Journal of Anaesthesia. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

The latest dictionary of nuclear energy term

International Nuclear Information System (INIS)

1996-06-01

This book is the latest dictionary of nuclear energy term. It deals with explanations of nuclear energy term in alphabetical order. It also lists abbreviation of nuclear energy term. This book contains symbol and unit, radiation units, greek letters, the symbol of for element, the table of an isotope and the periodic table on nuclear power term. It includes glossary of nuclear power in Korean and French and conceptual map about development of nuclear power.

Artificial sensory organs: latest progress.

Science.gov (United States)

Nakamura, Tatsuo; Inada, Yuji; Shigeno, Keiji

2018-03-01

This study introduces the latest progress on the study of artificial sensory organs, with a special emphasis on the clinical results of artificial nerves and the concept of in situ tissue engineering. Peripheral nerves have a strong potential for regeneration. An artificial nerve uses this potential to recover a damaged peripheral nerve. The polyglycolic acid collagen tube (PGA-C tube) is a bio-absorbable tube stuffed with collagen of multi-chamber structure that consists of thin collagen films. The clinical application of the PGA-C tube began in 2002 in Japan. The number of PGA-C tubes used is now beyond 300, and satisfactory results have been reported on peripheral nerve repairs. This PGA-C tube is also effective for patients suffering from neuropathic pain.

Development of a concept for the environmental risk assessment of biocidal products for authorization purposes (BIOEXPO). Executive summary

OpenAIRE

Dokkum, H.P. van; Scholten, M.C.Th.; Bakker, D.J.

1998-01-01

The Biocidal Products Directive (Draft 97/C69/03; latest version December 12' 1997, 95/0465 (COD); PE CONS 3633/97) will complete the European chemicals regulation, which consists of the directives on existing substances (Council regu-lation 793/93), new substances (Directive 92/32/EC) and agricultural pesticides (Directive 91/414/EC). Biocides include a wide range of product types, such as pest control products, disinfectants, preservatives, and antifouling products. In Annex V of the Biocid...

Current situation and prospect of market on the latest radiation measuring instrument

International Nuclear Information System (INIS)

Ha, Chang Ho; Kim, Wang Geum; Cho, Gyu Seong

2009-12-01

This book deals with current situation and prospect of market on the latest radiation measuring instrument. The contents of this book are basic of technology on radiation measuring instrument with basic principle of various measuring instrument, current situation of technology and prospect of radiation measuring instrument, effect of spreading and application field of radiation measuring instrument, facility for making and research and development of radiation measuring instrument, prospect of market about radiation measuring instrument, strategy for market entry with the latest radiation measuring instrument and general prospect for the future.

(The latest developments of the physical aspects of electrochemistry)

Energy Technology Data Exchange (ETDEWEB)

Liu, S.H.

1990-09-24

The author was one of 26 invited lecturers to discuss the latest developments of the physical aspects of electrochemistry. He interacted extensively with other lecturers and many participants from developing countries. He also visited with the Director of the Italian Synchrotron Radiation Source now under construction in Trieste, Italy.

Latest Results in SLAC 75-MW PPM Klystrons

International Nuclear Information System (INIS)

Sprehn, D.; Caryotakis, G.; Haase, A.; Jongewaard, E.; Laurent, L.; Pearson, C.; Phillips, R.

2006-01-01

75 MW X-band klystrons utilizing Periodic Permanent Magnet (PPM) focusing have been undergoing design, fabrication and testing at the Stanford Linear Accelerator Center (SLAC) for almost nine years. The klystron development has been geared toward realizing the necessary components for the construction of the Next Linear Collider (NLC). The PPM devices built to date which fit this class of operation consist of a variety of 50 MW and 75 MW devices constructed by SLAC, KEK (Tsukuba, Japan) and industry. All these tubes follow from the successful SLAC design of a 50 MW PPM klystron in 1996. In 2004 the latest two klystrons were constructed and tested with preliminary results reported at EPAC2004. The first of these two devices was tested to the full NLC specifications of 75 MW, 1.6 microseconds pulse length, and 120 Hz. This 14.4 kW average power operation came with a tube efficiency >50%. The most recent testing of these last two devices will be presented here. Design and manufacturing issues of the latest klystron, due to be tested by the Fall of 2005, are also discussed

Quality control of radioactive waste products

International Nuclear Information System (INIS)

Martens, B.R.; Warnecke, E.; Odoj, R.

1986-01-01

The variety of incoming untreated wastes, treatment methods, waste forms and containers requires a great variety of controlling methods and principles to be applied both during waste treatment and on the final product. The paper describes product control schemes and methods, sampling systems and transportable testing equipment for waste drums, and equipment for waste cementation using in-drum stirring and subsequent fixation of solid wastes in the flowable product. (DG) [de

The Validation of the GEWEX SRB Surface Shortwave Flux Data Products Using BSRN Measurements: A Systematic Quality Control, Production and Application Approach

Science.gov (United States)

Zhang, Taiping; Stackhouse, Paul W., Jr.; Gupta, Shashi K.; Cox, Stephen J.; Mikovitz, J. Colleen; Hinkelman, Laura M.

2013-01-01

The NASA/GEWEX Surface Radiation Budget (SRB) project has produced a 24.5-year continuous record of global shortwave and longwave radiation fluxes at TOA and the Earth's surface from satellite measurements. The time span of the data is from July 1983 to December 2007, and the spatial resolution is 11 latitude11 longitude. The inputs of the latest version (Release 3.0) include the GEOS Version 4.0.3 meteorological information and cloud properties derived from ISCCP DX data. The SRB products are available on 3-hourly, 3-hourly-monthly, daily and monthly time scales. To assess the quality of the product, we extensively validated the SRB data against 5969 site-months of groundbased measurements from 52 Baseline Surface Radiation Network (BSRN) stations. This paper describes first the characteristics of the BSRN data and the GEWEX SRB data, the methodology for quality control and processing of the shortwave BSRN data, and then the systematic SRB-BSRN comparisons. It is found that, except for occasional extreme outliers as seen in scatter plots, the satellite-based surface radiation data generally agree very well with BSRN measurements. Specifically, the bias/RMS for the daily and monthly mean shortwave fluxes are, respectively, -3.6/35.5 and -5.2/23.3W1 m2 under all-sky conditions.

Vane-Cam - camshaft controls with new functionalities; Vane-Cam - Nockenwellenversteller mit neuen Funktionalitaeten

Energy Technology Data Exchange (ETDEWEB)

Knecht, A.; Pohl, D. [Hydraulik-Ring GmbH, Nuertingen (Germany); Hannibal, W. [Fachhochschule Suedwestfalen, Iserlohn (Germany). Labor fuer Konstruktion und CAE-Anwendungen; enTec Consulting GmbH, Hemer (Germany)

2007-01-15

Infinitely variable camshaft phasing systems will be used in the future in practically all gasoline internal combustion engines high volume production. This paper of Hydraulik-Ring GmbH gives an overview of the current system concepts of the latest generation of camshaft controls utilizing the principle of the vane motor. (orig.)

PREVAIL: latest electron optics results

Science.gov (United States)

Pfeiffer, Hans C.; Golladay, Steven D.; Gordon, Michael S.; Kendall, Rodney A.; Lieberman, Jon E.; Rockrohr, James D.; Stickel, Werner; Yamaguchi, Takeshi; Okamoto, Kazuya; Umemoto, Takaaki; Shimizu, Hiroyasu; Kojima, Shinichi; Hamashima, Muneki

2002-07-01

The PREVAIL electron optics subsystem developed by IBM has been installed at Nikon's facility in Kumagaya, Japan, for integration into the Nikon commercial EPL stepper. The cornerstone of the electron optics design is the Curvilinear Variable Axis Lens (CVAL) technique originally demonstrated with a proof of concept system. This paper presents the latest experimental results obtained with the electron optical subsystem at Nikon's facility. The results include micrographs illustrating proper CVAL operation through the spatial resolution achieved over the entire optical field of view. They also include data on the most critical issue of the EPL exposure approach: subfield stitching. The methodology of distortion correction will be described and both micrographs and metrology data of stitched subfields will be presented. This paper represents a progress report of the IBM/Nikon alliance activity on EPL.

Advanced methods of quality control in nuclear fuel fabrication

International Nuclear Information System (INIS)

Onoufriev, Vladimir

2004-01-01

Under pressure of current economic and electricity market situation utilities implement more demanding fuel utilization schemes including higher burn ups and thermal rates, longer fuel cycles and usage of Mo fuel. Therefore, fuel vendors have recently initiated new R and D programmes aimed at improving fuel quality, design and materials to produce robust and reliable fuel. In the beginning of commercial fuel fabrication, emphasis was given to advancements in Quality Control/Quality Assurance related mainly to product itself. During recent years, emphasis was transferred to improvements in process control and to implementation of overall Total Quality Management (TQM) programmes. In the area of fuel quality control, statistical control methods are now widely implemented replacing 100% inspection. This evolution, some practical examples and IAEA activities are described in the paper. The paper presents major findings of the latest IAEA Technical Meetings (TMs) and training courses in the area with emphasis on information received at the TM and training course held in 1999 and other latest publications to provide an overview of new developments in process/quality control, their implementation and results obtained including new approaches to QC

Operating experience on radiation reduction in the latest BWRs

International Nuclear Information System (INIS)

Ohsumi, K.; Uchida, S.; Aizawa, M.; Takagi, K.; Amano, O.; Yamashita, K.

1988-01-01

In Japan, BWR plants have been operated commercially since 1970, and the reduction of radiation exposure has been an important concern. The application of the procedure for reducing occupational exposure is incorporated in Japanese Improvement and Standardization Program for LWRs. No.2 and No.4 plants in Fukushima No.2 Nuclear Power Station were designed and constructed as the latest 1,100 MWe BWRs in conformity with the Improvement and Standardization Program. No.2 plant began the commercial operation in February, 1984, and experienced three times of the scheduled annual maintenance outage. No.4 plant began the commercial operation in September, 1987, and the first annual maintenance is scheduled from September, 1988. In this paper, discussion is focused on recent radiation reduction measures, that is the control of iron and nickel in primary coolant for reducing the radiation dose rate in primary systems, based on the experience with No.2 and No.4 plants. The design concept of a low radiation dose rate nuclear power plant, the experience on water chemistry in No.2 plant, the control of iron and nickel in No.4 plant operation and so on are reported. It is believed that these operation experiences contribute to the reduction of occupational exposure in BWR plants currently in operation and in future. (Kako, I.)

2. Product quality control and assurance system

International Nuclear Information System (INIS)

1990-01-01

Product quality control and assurance are dealt with in relation to reliability in nuclear power engineering. The topics treated include product quality control in nuclear power engineering, product quality assurance of nuclear power plant equipment, quality assurance programs, classification of selected nuclear power equipment, and standards relating to quality control and assurance and to nuclear power engineering. Particular attention is paid to Czechoslovak and CMEA standards. (P.A.). 2 figs., 1 tab., 12 refs

Latest Results On Jet Production and Properties from the LHC

CERN Document Server

Jones, G

2012-01-01

Investigations of jets performed by the ATLAS and CMS collaborations using collisions at $\\sqrt{s}$ = 7 TeV are described. To pics of interest are jet performance, production and the precision measurement of their properties. Comparison of the results to theoretical predictions are discussed and areas with poor agreement identified.

Sport nutrition: A review of the latest guidelines for exercise and ...

African Journals Online (AJOL)

Sport nutrition: A review of the latest guidelines for exercise and sport nutrition from the American College of Sport Nutrition, the International Olympic Committee and the International Society for Sports Nutrition.

Cina Benteng: The Latest Generations and Acculturation

Directory of Open Access Journals (Sweden)

Billy Nathan Setiawan

2015-05-01

Full Text Available The aim of this paper was to investigate the acculturation process encountered by the two latest generations of Cina Benteng. A Skype interview was conducted with two young Cina Benteng descents. The analysis was also supported by insightful remark from the parents of the two interviewees. This study discovers that the two generations seem to respond to the acculturation process in different ways. However, although some traditions are no longer relevant to the later generation, their identity as a Chinese descent cannot be easily removed.

Integrated approach to economical, reliable, safe nuclear power production

International Nuclear Information System (INIS)

1982-06-01

An Integrated Approach to Economical, Reliable, Safe Nuclear Power Production is the latest evolution of a concept which originated with the Defense-in-Depth philosophy of the nuclear industry. As Defense-in-Depth provided a framework for viewing physical barriers and equipment redundancy, the Integrated Approach gives a framework for viewing nuclear power production in terms of functions and institutions. In the Integrated Approach, four plant Goals are defined (Normal Operation, Core and Plant Protection, Containment Integrity and Emergency Preparedness) with the attendant Functional and Institutional Classifications that support them. The Integrated Approach provides a systematic perspective that combines the economic objective of reliable power production with the safety objective of consistent, controlled plant operation

Direct product quality control for energy efficient climate controlled transport of agro-material

NARCIS (Netherlands)

Verdijck, G.J.C.; Preisig, H.A.; Straten, van G.

2005-01-01

A (model-based) Product Quality Controller is presented for climate controlled operations involving agro-material, such as storage and transport. This controller belongs to the class of Model Predictive Controllers and fits in a previously developed hierarchical control structure. The new Product

Alternative solvents for natural products extraction

CERN Document Server

Chemat, Farid

2014-01-01

This book presents a complete picture of the current state-of-the-art in alternative and green solvents used for laboratory and industrial natural product extraction in terms of the latest innovations, original methods and safe products. It provides the necessary theoretical background and details on extraction, techniques, mechanisms, protocols, industrial applications, safety precautions and environmental impacts. This book is aimed at professionals from industry, academicians engaged in extraction engineering or natural product chemistry research, and graduate level students. The individual chapters complement one another, were written by respected international researchers and recognized professionals from the industry, and address the latest efforts in the field. It is also the first sourcebook to focus on the rapid developments in this field.

Systematic Product Development of Control and Diagnosis Functionalities

Science.gov (United States)

Stetter, R.; Simundsson, A.

2017-01-01

In the scientific field of systematic product development a wide range of helpful methods, guidelines and tools were generated and published in recent years. Until now little special attention was given to design guidelines aiming at supporting product development engineers to design products that allow and support control or diagnosis functions. The general trend to ubiquitous computing and the first development steps towards cognitive systems as well as a general trend toward higher product safety, reliability and reduced total cost of ownership (TCO) in many engineering fields lead to a higher importance of control and diagnosis. In this paper a first attempt is made to formulate general valid guidelines how products can be developed in order to allow and to achieve effective and efficient control and diagnosis. The guidelines are elucidated on the example of an automated guided vehicle. One main concern of this paper is the integration of control and diagnosis functionalities into the development of complete systems which include mechanical, electrical and electronic subsystems. For the development of such systems the strategies, methods and tools of systematic product development have attracted significant attention during the last decades. Today, the functionality and safety of most products is to a large degree dependent on control and diagnosis functionalities. Still, there is comparatively little research concentrating on the integration of the development of these functionalities into the overall product development processes. The paper starts with a background describing Systematic Product Development. The second section deals with the product development of the sample product. The third part clarifies the notions monitoring, control and diagnosis. The following parts summarize some insights and formulate first hypotheses concerning control and diagnosis in Systematic Product Development.

Automatic control algorithm effects on energy production

Science.gov (United States)

Mcnerney, G. M.

1981-01-01

A computer model was developed using actual wind time series and turbine performance data to simulate the power produced by the Sandia 17-m VAWT operating in automatic control. The model was used to investigate the influence of starting algorithms on annual energy production. The results indicate that, depending on turbine and local wind characteristics, a bad choice of a control algorithm can significantly reduce overall energy production. The model can be used to select control algorithms and threshold parameters that maximize long term energy production. The results from local site and turbine characteristics were generalized to obtain general guidelines for control algorithm design.

Management Control in New Product Development

DEFF Research Database (Denmark)

Jørgensen, Brian; Messner, Martin

2009-01-01

organizations to better manage tensions between efficiency and flexibility, which is arguably a key issue in many organizations today. Our paper contributes to this stream of research by detailing how enabling control functions in the particular setting of new product development. To this end, we draw upon......Several studies in management control have drawn upon the concepts of coercive and enabling forms of bureaucracy (Adler and Borys 1996) to discuss how the features of a control system may affect employees' attitudes toward control. This question is relevant because enabling forms of control allow...... and flexibility. In addition, our paper sets out to explore how strategic change can influence the operation of enabling control. Focusing on the introduction of a new product strategy in our case organization, we describe employees' repair efforts in adapting the control system to their own needs. We find...

Principles for determining the economic competence of production units

Energy Technology Data Exchange (ETDEWEB)

Gubanova, O D; Makhlina, M I

1980-01-01

In the general plan for controlling the sector ''Geology and Exploration of the Depths'', a reduction is stipulated in the number of independent organizations and their inclusion as production units in the production geological associations. Distribution of rights and duties between the association and the production units is very important. Presentation to rights of the leaders to the lowest level to independently solve operational questions allows the leadership of the association to focus attention on solving major problems. The production units are given qualitative fulfillment of geological and production assignments, guarantee of improved efficiency of work, labor productivity and decrease in cost of the work; introduction of the latest achievements of science and technology; observation of the regime for conservation and efficient use of monetary resources, material and labor resources. There are natural interrelationships between specialization of production, centralization of the control functions and a change in the volume of authority of the production units. The legal status of the production unit is presented in two documents: statutes on the production geological association and statutes on the given production unit approved by the general director of the association. Principles are revealed for centralizing the rights needed to fulfill the functions following from national economic responsibility of the production geological association. This is long-term planning and forecasting, control of scientific-technical progress, scientific research, etc., control of the property, establishment of unified conditions for organization of labor and wages, construction, etc.

The latest occupational radiation exposure data from U.S. Nuclear Regulatory Commission Licensees

International Nuclear Information System (INIS)

Brock, T.

2007-01-01

This presentation summarizes the latest - 2005 occupational exposure data that are maintained in the U.S. Nuclear Regulatory Commission (NRC) Radiation Exposure Information and Reporting System. The bulk of the information contained in the paper was compiled from the 2005 annual reports submitted by NRC licensees subject to the reporting requirements of U.S. regulations (10 CFR 20.2206). Those licensees subject to reporting include commercial nuclear power plants, industrial radiographers, fuel processors, independent spent fuel storage installations, manufacturers and distributors of by-product material, facilities for low-level waste disposal, and geologic repositories for high-level waste. The annual reports submitted by these licensees consist of radiation exposure records for each monitored individual. These records are analyzed for trends and presented in terms of collective dose and the distribution of doses by licensee category. (author)

Turbomachinery: latest developments in a changing scene

International Nuclear Information System (INIS)

1991-01-01

The contributions to the 1991 European Conference on the latest developments in turbomachinery are presented. The topics covered include: computational fluid dynamics methods applied to the aerodynamics of turbine blades; developments associated with steam turbines and gas turbines; flow patterns for turbine blades; compressor design and development; turbine test facilities; film cooling; heat transfer; theoretical treatment of transonic and unsteady flow; condensation phenomena and wet steam flow; water extraction from steam turbine blades; wetness losses in steam turbines in nuclear power plants and pressure loss reduction; aerodynamic instabilities arising from governing valves in Pressurized Water Reactor steam turbines. (UK)

21 CFR 820.70 - Production and process controls.

Science.gov (United States)

2010-04-01

...) MEDICAL DEVICES QUALITY SYSTEM REGULATION Production and Process Controls § 820.70 Production and process... used as part of production or the quality system, the manufacturer shall validate computer software for... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Production and process controls. 820.70 Section...

Open-pit production and control at Roessing

International Nuclear Information System (INIS)

Hodson, D.; Rich, C.

1986-01-01

In recent years metal prices have been severely depressed and most companies have directed efforts to controlling costs in order to stay in business. Roessing Uranium has consistently kept uranium production cost increases well below the domestic inflation rate and this has been the result of a firm commitment to production and cost control, which is the main theme of this paper. The subject of cost analysis is briefly presented and the paper then gives more technical detail under the main headings of grade control, production control and engineering projects. The main communication channels, which are used to ensure that different departments on the mine are all working for the same objectives, are mentioned. The paper, however, is intended to be a general overview of the engineering aspects of open-pit cost control

Radiological control of food importation products

International Nuclear Information System (INIS)

Aguirre G, J.

2003-01-01

Nowadays exists the possibility of marketing products possibly polluted with radioactive isotopes, by that some countries like Mexico, they have been given to the task of creating legal bases and the necessary infrastructure with the end of carrying out the radiological surveillance of nutritious import products. In this work the legal bases that our country has established for the radiological control are presented besides the results of this radiological control carried out through the gamma spectroscopy analysis of nutritious import products sent to our country through diverse companies that import foods produced mainly in European countries. (Author)

Multiple episodes of extensive marine anoxia linked to global warming and continental weathering following the latest Permian mass extinction.

Science.gov (United States)

Zhang, Feifei; Romaniello, Stephen J; Algeo, Thomas J; Lau, Kimberly V; Clapham, Matthew E; Richoz, Sylvain; Herrmann, Achim D; Smith, Harrison; Horacek, Micha; Anbar, Ariel D

2018-04-01

Explaining the ~5-million-year delay in marine biotic recovery following the latest Permian mass extinction, the largest biotic crisis of the Phanerozoic, is a fundamental challenge for both geological and biological sciences. Ocean redox perturbations may have played a critical role in this delayed recovery. However, the lack of quantitative constraints on the details of Early Triassic oceanic anoxia (for example, time, duration, and extent) leaves the links between oceanic conditions and the delayed biotic recovery ambiguous. We report high-resolution U-isotope (δ 238 U) data from carbonates of the uppermost Permian to lowermost Middle Triassic Zal section (Iran) to characterize the timing and global extent of ocean redox variation during the Early Triassic. Our δ 238 U record reveals multiple negative shifts during the Early Triassic. Isotope mass-balance modeling suggests that the global area of anoxic seafloor expanded substantially in the Early Triassic, peaking during the latest Permian to mid-Griesbachian, the late Griesbachian to mid-Dienerian, the Smithian-Spathian transition, and the Early/Middle Triassic transition. Comparisons of the U-, C-, and Sr-isotope records with a modeled seawater PO 4 3- concentration curve for the Early Triassic suggest that elevated marine productivity and enhanced oceanic stratification were likely the immediate causes of expanded oceanic anoxia. The patterns of redox variation documented by the U-isotope record show a good first-order correspondence to peaks in ammonoid extinctions during the Early Triassic. Our results indicate that multiple oscillations in oceanic anoxia modulated the recovery of marine ecosystems following the latest Permian mass extinction.

Product Control of Waste Products with New Coating Materials

International Nuclear Information System (INIS)

Krumbach, H.; Steinmetz, H.J.; Odoj, R.; Wartenberg, W.; Grunau, H.

2009-01-01

In Germany, with the shaft KONRAD a repository for low radioactive waste will be available at the earliest in the year 2013. The previously conditioned radioactive waste has to be suitable for a longer-term interim storage. They have to be treated in a way that they are chemically stable and that their integrity is guaranteed for a long time. That is why the waste product or the container is covered/ coated for special waste such as hygroscopic waste or waste that includes aluminium. The Product Control Group for radioactive waste (PKS) has to proof the suitability of the so-treated waste for the repository KONRAD on behalf of the Federal Office for Radiation Protection (BfS). This has to be done before the delivering. In this context the PKS also assesses the suitability of new coating materials for low radioactive waste products or containers and their correct technical application. The characteristics and the technical application of polyurethane coatings as well as the control of the so-coated waste for the disposal in the shaft KONRAD are described in this poster. The Poster shows the development stages of the coating and the filling. There are also shown the boundary conditions and the investigations of the Product Control Group for the use of the new coating material for radioactive waste. (authors)

Wind Plant Models in IEC 61400-27-2 and WECC - latest developments in international standards on wind turbine and wind plant modeling

DEFF Research Database (Denmark)

Fortmann, Jens; Miller, Nicholas; Kazachkov, Yuri

2015-01-01

This paper describes the latest developments in the standardization of wind plant and wind plant controller models. As a first step IEC TC88 WG 27 and WECC jointly developed generic wind turbine models which have been published by WECC in 2014 and IEC in 2015 as IEC 61400-27-1, which also include...

Modern control of mineral wool production process

Directory of Open Access Journals (Sweden)

Stankov Stanko P.

2013-01-01

Full Text Available In this paper, the control of the plant for mineral wool production consisting of a number of the technological units of different sizes and complexity is considered. The application of modern equipment based on PLC (Programmable Logic Controller and SCADA (Supervisory Control And Data Acquisition configuration provides optimal control of technological process. Described supervisory and control system is consisting of a number of units doing decentralized distributed control of technological entities where all possible situation are considered during work of machines and devices, which are installed in electric drive and are protected from technological and electrical accident. Transformer station and diesel engine, raw materials transport and dosage, processes in dome oven, centrifuges, polycondensation (PC chamber, burners, compressor station, binder preparation and dosage, wool cutting, completed panel packing and their transport to storehouse are controlled. Process variables and parameters like as level, flow, velocity, temperature, pressure, etc. are controlled. Control system is doing identification of process states changes, diagnostic and prediction of errors and provides prediction of behavior of control objects when input flows of materials and generates optimal values of control variables due to decreasing downtime and technic - economical requires connected to wool quality to be achieved. Supervisory and control system either eliminates unwanted changes in the production line or restricts them within the allowable limits according to the technology. In this way, the optimization of energy and raw materials consumption and appropriate products quality is achieved, where requirements are satisfied in accordance with process safety and environmental standards. SCADA provides a visual representation of controlled and uncontrolled parts of the technological process, processing alarms and events, monitoring of the changes of relevant

The DIVA model: A neural theory of speech acquisition and production.

Science.gov (United States)

Tourville, Jason A; Guenther, Frank H

2011-01-01

The DIVA model of speech production provides a computationally and neuroanatomically explicit account of the network of brain regions involved in speech acquisition and production. An overview of the model is provided along with descriptions of the computations performed in the different brain regions represented in the model. The latest version of the model, which contains a new right-lateralized feedback control map in ventral premotor cortex, will be described, and experimental results that motivated this new model component will be discussed. Application of the model to the study and treatment of communication disorders will also be briefly described.

Non-Formal Education Implementations in Turkey: Issues and Latest Challenges

Science.gov (United States)

Bilir, Mehmet

2007-01-01

The aim of this article is to analyse the latest implementations and issues raised in Turkish non-formal education from a historical perspective in Turkey. The high population rate and lack of adequate educational opportunities for adults and migration from rural areas to urban areas caused many educational, social and cultural problems in…

The latest results on top quark pair cross-section measurement at the LHC-ATLAS experiment

CERN Document Server

Yamauchi, Katsuya; The ATLAS collaboration

2015-01-01

The latest results on top quark pair production cross-section measurement in proton-proton collisions at $\\sqrt{s}$ = 7\\,TeV and $\\sqrt{s}$ = 8\\,TeV with the ATLAS detector are reported. The inclusive cross-section was measured with relative uncertainty of 4\\% using the final state of the top quark pair including an electron and a muon. The measurement of the differential cross-section as functions of various observables such as the transverse momentum and the rapidity of the top quark and the invariant mass of the top quark pair system are also reported. These results are compared with various generators such as {\\sc Powheg}, {\\sc Alpgen} and {\\sc MC@NLO} and various sets of parton distribution functions.

Case Studies in Modelling, Control in Food Processes.

Science.gov (United States)

Glassey, J; Barone, A; Montague, G A; Sabou, V

This chapter discusses the importance of modelling and control in increasing food process efficiency and ensuring product quality. Various approaches to both modelling and control in food processing are set in the context of the specific challenges in this industrial sector and latest developments in each area are discussed. Three industrial case studies are used to demonstrate the benefits of advanced measurement, modelling and control in food processes. The first case study illustrates the use of knowledge elicitation from expert operators in the process for the manufacture of potato chips (French fries) and the consequent improvements in process control to increase the consistency of the resulting product. The second case study highlights the economic benefits of tighter control of an important process parameter, moisture content, in potato crisp (chips) manufacture. The final case study describes the use of NIR spectroscopy in ensuring effective mixing of dry multicomponent mixtures and pastes. Practical implementation tips and infrastructure requirements are also discussed.

Production process and quality control for the HTTR fuel

International Nuclear Information System (INIS)

Yoshimuta, S.; Suzuki, N.; Kaneko, M.; Fukuda, K.

1991-01-01

Development of the production and inspection technology for High Temperature Engineering Test Reactor (HTTR) fuel has been carried out by cooperative work between Japan Atomic Energy Research Institute (JAERI) and Nuclear Fuel Industries, Ltd (NFI). The performance and the quality level of the developed fuel are well established to meet the design requirements of the HTTR. For the commercial scale production of the fuel, statistical quality control and quality assurance must be carefully considered in order to assure the safety of the HTTR. It is also important to produce the fuel under well controlled process condition. To meet these requirements in the production of the HTTR fuel, a new production process and quality control system is to be introduced in the new facilities. The main feature of the system is a computer integrated control system. Process control data at each production stage of products and semi-products are all gathered by terminal computers and processed by a host computer. The processed information is effectively used for the production, quality and accountancy control. With the aid of this system, all the products will be easily traceable from starting materials to final stages and the statistical evaluation of the quality of products becomes more reliable. (author). 8 figs

Latest innovations for tattoo and permanent makeup removal.

Science.gov (United States)

Mao, Johnny C; DeJoseph, Louis M

2012-05-01

The goal of this article is to reveal the latest techniques and advances in laser removal of both amateur and professional tattoos, as well as cosmetic tattoos and permanent makeup. Each pose different challenges to the removing physician, but the goal is always the same: removal without sequelae. The authors' technique is detailed, and discussion of basic principles of light reflection, ink properties, effects of laser energy and heat, and outcomes and complications of tattoo removal are presented. Copyright © 2012 Elsevier Inc. All rights reserved.

[Health risks from pest control products].

Science.gov (United States)

Pieper, C; Holthenrich, D; Schneider, H

2014-05-01

According to European biocide legislation, pest control products require assessment and authorization by the responsible national or European authorities. Biocidal products can only be authorized if they have no unacceptable effects on human health. The health risk assessment performed for authorization comprises (a) the derivation of reference values for the active substances and substances of concern contained in the biocidal product and (b) an exposure assessment. These parameters are required for risk characterization. No unacceptable health risks are expected if the determined exposure is less than the relevant reference value. In addition, the toxicological information is used for classification of the biocidal product. The assessment may, where necessary, result in specific conditions for use or other restrictions aimed at minimizing risk. The risk to human health from pest control products is mainly based on the toxicological properties of their active substances. Commonly, the coformulants used in pest control products are of less concern than the active substances (e.g., food ingredients and animal feed products). For example, most rodenticides belong to the group of anticoagulants, which are also effective in humans. Regarding intoxications through insecticides, the group of pyrethroids is of particular importance. Fumigants containing metal phosphides, hydrogen cyanide, or sulfuryl difluoride are particularly toxic. This toxicity is linked to the high acute inhalation toxicity of the gaseous active substances themselves or, in the case of phosphides, of the released gas phosphane. The aim of health risk assessment for the authorization of biocidal products is to ensure their safe application for users and all other persons involved, assuming an adequate and label-compliant use.

Assessment of Fuel Analysis Methodology and Fission Product Release for 37-Element Fuel by Using the Latest IST Codes during Stagnation Feeder Break in CANDU

International Nuclear Information System (INIS)

Park, Joo Hwan; Jung, Jong Yeob

2009-09-01

Feeder break accident is regarded as one of the design basis accident in CANDU reactor which results in a fuel failure. For a particular range of inlet feeder break sizes, the flow in the channel is reduced sufficiently that the fuel and fuel channel integrity can be significantly affected to have damage in the affected channel, while the remainder of the core remains adequately cooled. The flow in the downstream channel can be more or less stagnated due to a balance between pressure at the break on the upstream side and the reverse driving pressure between the break and the downstream end. In the extreme, this can lead to rapid fuel heatup and fuel damage and failure of the fuel channel similar to that associated with a severe channel flow blockage. Such an inlet feeder break scenario is called a stagnation break. In this report, the fuel analysis methodology and the assessment results of fission product inventory and release during the stagnation feeder break are described for conservatively assumed limiting channel. The accident was assumed to be occurred in the refurbished Wolsong unit 1 and the latest safety codes were used in the analysis. Fission product inventories during the steady state were calculated by using ELESTRES-IST 1.2 code. The whole analysis process was carried out by a script file which was programmed by Perl language. The perl script file was programmed to make all ELESTRES input files for each bundle and each ring based on the given power-burnup history and thermal-hydraulic conditions of the limiting channel and to perform the fuel analysis automatically. The fission product release during the transient period of stagnation feeder break was evaluated by applying Gehl model. The amounts of each isotope's release are conservatively evaluated for additional 2 seconds after channel failure. The calculated fission product releases are provided to the following dose assessment as a source term

Strategies of Production Control as Tools of Efficient Management of Production Enterprises

Science.gov (United States)

Budynek, Mateusz; Celińska, Elżbieta; Dybikowska, Adrianna; Kozak, Monika; Ratajczak, Joanna; Urban, Jagoda; Materne, Karolina

2016-03-01

The paper discusses the problem of principle methods of production control as a strategy supporting the production system and stimulating efficient solutions in respect management in production enterprises. The article describes MRP, ERP, JIT, KANBAN and TOC methods and focuses on their main goals, principles of functioning as well as benefits resulting from their application. The methods represent two diverse strategies of production control, i.e. pull and push strategies. Push strategies are used when the plans apply to the first and principle part of production and are based on the demand forecasts. Pull strategies are used when all planning decisions apply to the final stage and depend on the actual demand or orders from customers.

Latest Cretaceous climatic and environmental change in the South Atlantic region

NARCIS (Netherlands)

Woelders, L.; Vellekoop, J.; Kroon, D.; Smit, J.; Casadío, S.; Prámparo, M. B.; Dinarès-Turell, J.; Peterse, F.; Sluijs, A.; Lenaerts, J.T.M.; Speijer, R. P.

Latest Maastrichtian climate change caused by Deccan volcanism has been invoked as a cause of mass extinction at the Cretaceous-Paleogene (K-Pg) boundary (~66.0 Ma). Yet late Maastrichtian climate and ecological changes are poorly documented, in particular on the Southern Hemisphere. Here we present

Latest Cretaceous climatic and environmental change in the South Atlantic region

NARCIS (Netherlands)

Woelders, L.; Vellekoop, J.; Kroon, D.; Smit, J.; Casadío, S.; Prámparo, M. B.; Dinarès-Turell, J.; Peterse, F.; Sluijs, A.; Lenaerts, J. T.M.; Speijer, R. P.

2017-01-01

Latest Maastrichtian climate change caused by Deccan volcanism has been invoked as a cause of mass extinction at the Cretaceous-Paleogene (K-Pg) boundary (~66.0 Ma). Yet late Maastrichtian climate and ecological changes are poorly documented, in particular on the Southern Hemisphere. Here we present

STRATEGIES OF PRODUCTION CONTROL AS TOOLS OF EFFICIENT MANAGEMENT OF PRODUCTION ENTERPRISES

Directory of Open Access Journals (Sweden)

Mateusz BUDYNEK

2016-01-01

Full Text Available The paper discusses the problem of principle methods of production control as a strategy supporting the production system and stimulating efficient solutions in respect management in production enterprises. The article describes MRP, ERP, JIT, KANBAN and TOC methods and focuses on their main goals, principles of functioning as well as benefits re-sulting from their application. The methods represent two diverse strategies of production control, i.e. pull and push strategies. Push strategies are used when the plans apply to the first and principle part of production and are based on the demand forecasts. Pull strategies are used when all planning decisions apply to the final stage and depend on the actual demand or orders from customers.

[Pharmaceutical product quality control and good manufacturing practices].

Science.gov (United States)

Hiyama, Yukio

2010-01-01

This report describes the roles of Good Manufacturing Practices (GMP) in pharmaceutical product quality control. There are three keys to pharmaceutical product quality control. They are specifications, thorough product characterization during development, and adherence to GMP as the ICH Q6A guideline on specifications provides the most important principles in its background section. Impacts of the revised Pharmaceutical Affairs Law (rPAL) which became effective in 2005 on product quality control are discussed. Progress of ICH discussion for Pharmaceutical Development (Q8), Quality Risk Management (Q9) and Pharmaceutical Quality System (Q10) are reviewed. In order to reconstruct GMP guidelines and GMP inspection system in the regulatory agencies under the new paradigm by rPAL and the ICH, a series of Health Science studies were conducted. For GMP guidelines, product GMP guideline, technology transfer guideline, laboratory control guideline and change control system guideline were written. For the GMP inspection system, inspection check list, inspection memo and inspection scenario were proposed also by the Health Science study groups. Because pharmaceutical products and their raw materials are manufactured and distributed internationally, collaborations with other national authorities are highly desired. In order to enhance the international collaborations, consistent establishment of GMP inspection quality system throughout Japan will be essential.

The Latest Books on Globalization

Directory of Open Access Journals (Sweden)

Elia Zaru

2016-12-01

Full Text Available The latest books published on globalization raise interesting issues which reflect upon the very complexity of the process we are facing. In The Great Convergence: Information Technology and the New Globalization Richard Baldwin proposes a history of globalization divided into two stages. As Baldwin argues, the process of globalization has to be divided into “old” and “new” age. The “old” globalization took place between 1820 and 1990. It was characterized by the “great divergence”, that is by the centralization of world income in today’s wealthy nations. However, since 1990 the sharing of world income has plummeted to where it was in 1900. According to Baldwin, this reversal of fortune is a symptom of a shift in the globalization process. The “new” globalization, driven by information technology, has combined high tech with low wages, and lead simultaneously to the industrialization of developing nations and deindustrialization of developed ones. This is the “great convergence”: in the “new” globalization rich and developing nations are alike and they face equal global challenges.

Sport nutrition: A review of the latest guidelines for exercise and ...

African Journals Online (AJOL)

Sport nutrition: A review of the latest guidelines for exercise and sport nutrition from the American College of Sport Nutrition, the International Olympic Committee ... Habitual carbohydrate intake is essential for physically active individuals and should be timed according to training sessions to ensure optimal pre-, during, and ...

Mechatronic System Design and Intelligent Motion Control of Hydraulic Robots and Machines

DEFF Research Database (Denmark)

Conrad, Finn; Sørensen, Torben

2003-01-01

The paper presents an approach and concept to mechatronic system design and intelligent motion control. The Information Technology (IT) offers software and hardware for improvement of R&D Mechatronic Teams to create products and solutions for industrial applications. The latest progress in IT makes...... integration of an overall design and manufacturing IT- concept feasible and commercially attractive. An IT-tool concept for modelling, simulation and design of mechatronic products and systems is proposed in this paper. It built on results from a Danish mechatronic research program on intelligent motion...

Latest Cretaceous climatic and environmental change in the South Atlantic region

Science.gov (United States)

Woelders, L.; Vellekoop, J.; Kroon, D.; Smit, J.; Casadío, S.; Prámparo, M. B.; Dinarès-Turell, J.; Peterse, F.; Sluijs, A.; Lenaerts, J. T. M.; Speijer, R. P.

2017-05-01

Latest Maastrichtian climate change caused by Deccan volcanism has been invoked as a cause of mass extinction at the Cretaceous-Paleogene (K-Pg) boundary ( 66.0 Ma). Yet late Maastrichtian climate and ecological changes are poorly documented, in particular on the Southern Hemisphere. Here we present upper Maastrichtian-lower Danian climate and biotic records from the Bajada del Jagüel (BJ) shelf site (Neuquén Basin, Argentina), employing the TEX86 paleothermometer, marine palynology (dinoflagellate cysts), and micropaleontology (foraminifera). These records are correlated to the astronomically tuned Ocean Drilling Program Site 1262 (Walvis Ridge). Collectively, we use these records to assess climatic and ecological effects of Deccan volcanism in the Southern Atlantic region. Both the TEX86-based sea surface temperature (SST) record at BJ and the bulk carbonate δ18O-based SST record of Site 1262 show a latest Maastrichtian warming of 2.5-4°C, at 450 to 150 kyr before the K-Pg boundary, coinciding with the a large Deccan outpouring phase. Benthic foraminiferal and dinocyst assemblage changes indicate that this warming resulted in enhanced runoff and stratification of the water column, likely resulting from more humid climate conditions in the Neuquén Basin. These climate conditions could have been caused by an expanding and strengthening thermal low over the South American continent. Biotic changes in response to late Maastrichtian environmental changes are rather limited, when compared to the major turnovers observed at many K-Pg boundary sites worldwide. This suggests that environmental perturbations during the latest Maastrichtian warming event were less severe than those following the K-Pg boundary impact.

Mechanics of human voice production and control.

Science.gov (United States)

Zhang, Zhaoyan

2016-10-01

As the primary means of communication, voice plays an important role in daily life. Voice also conveys personal information such as social status, personal traits, and the emotional state of the speaker. Mechanically, voice production involves complex fluid-structure interaction within the glottis and its control by laryngeal muscle activation. An important goal of voice research is to establish a causal theory linking voice physiology and biomechanics to how speakers use and control voice to communicate meaning and personal information. Establishing such a causal theory has important implications for clinical voice management, voice training, and many speech technology applications. This paper provides a review of voice physiology and biomechanics, the physics of vocal fold vibration and sound production, and laryngeal muscular control of the fundamental frequency of voice, vocal intensity, and voice quality. Current efforts to develop mechanical and computational models of voice production are also critically reviewed. Finally, issues and future challenges in developing a causal theory of voice production and perception are discussed.

Top quark production at the LHC

CERN Document Server

Ferreira da Silva, Pedro

2016-01-01

Twenty years past its discovery, the top quark continues attracting great interest as experiments keep unveiling its properties. An overview of the latest measurements in the domain of top quark production, performed by the ATLAS and CMS experiments at the CERN LHC, is given. The latest measurements of top quark production rates via strong and electroweak processes are reported and compared to different perturbative QCD predictions. Fundamental properties, such as the mass or the couplings of the top quark, as well as re-interpretations seeking for beyond the standard model contributions in the top quark sector, are extracted from these measurements. In each case an attempt to highlight the first results and main prospects for the on-going Run 2 of the LHC is made.

The latest full-scale PWR simulator in Japan

International Nuclear Information System (INIS)

Nishimuru, Y.; Tagi, H.; Nakabayashi, T.

2004-01-01

The latest MHI Full-scale Simulator has an excellent system configuration, in both flexibility and extendability, and has highly sophisticated performance in PWR simulation by the adoption of CANAC-II and PRETTY codes. It also has an instructive character to display the plant's internal status, such as RCS condition, through animation. Further, the simulation has been verified to meet a functional examination at model plant, and with a scale model test result in a two-phase flow event, after evaluation for its accuracy. Thus, the Simulator can be devoted to a sophisticated and broad training course on PWR operation. (author)

Control of dust production in ITER

International Nuclear Information System (INIS)

Rodriguez-Rodrigo, L.; Ciattaglia, S.; Elbez-Uzan, J.

2006-01-01

In the last years dust has been observed in a number of fusion devices and is being studied more in detail for understanding in particular the physical phenomena related to its formation, its composition, physical and chemical characteristics, and the amount of produced dust. The extrapolation of dust formation to ITER predicts (with large error bars), a large mass of dust production with a scattered size distribution. To evaluate the impact of dust on safety, assumptions have also been made on radionuclide inventory, and mobility in off-normal events, as well as any postulated contributions the dust may make to effluents or accidental releases. Solid activation products in structures are generally not readily mobilisable in incidental and accidental situations, so that activated dust, tritium and activated corrosions products are the important in-vessel source terms in postulated scenarios that assume a mobilisation and release of some fraction of this inventory. Such a release would require the simultaneous leak or bypass of several robust confinement barriers. Further concerns for dust may be the potential for chemical reactions between dust and coolant in the event of an in-vessel leak, and the theoretical possibility of a dust explosion, either of which could in principle cause a pressure rise that challenges one or more of the confinement barriers. Although these hazards can - and will - be controlled by other measures in the ITER design, application of the principle of Defence in Depth dictates that the dust inventory should also be minimised and controlled to prevent the potential hazard. A well-coordinated R-and-D programme is required to support this dust production control. This document provides from the safety point of view, an overview of existing data given in '' Dossier d'Options de Surete '', the first safety report presented in 2001 to the French Safety Authorities, and ITER documents; it also gathers information on status of studies on activated

Mobile application for reading latest news from multiple sources

OpenAIRE

Watzak, Aleš

2013-01-01

Thesis covers development of an application for mobile devices running Android operating system. It enables users to keep up to date with the latest news, weather and traffic report. News delivery service is available wherever there is Internet access and not limited to a physical location like an office with desktop computer. To this end we developed two applications. First represents server part of the application and runs on Apache web server. The second part is a client application which ...

Optimal Control Inventory Stochastic With Production Deteriorating

Science.gov (United States)

Affandi, Pardi

2018-01-01

In this paper, we are using optimal control approach to determine the optimal rate in production. Most of the inventory production models deal with a single item. First build the mathematical models inventory stochastic, in this model we also assume that the items are in the same store. The mathematical model of the problem inventory can be deterministic and stochastic models. In this research will be discussed how to model the stochastic as well as how to solve the inventory model using optimal control techniques. The main tool in the study problems for the necessary optimality conditions in the form of the Pontryagin maximum principle involves the Hamilton function. So we can have the optimal production rate in a production inventory system where items are subject deterioration.

Software product quality control

CERN Document Server

Wagner, Stefan

2013-01-01

Quality is not a fixed or universal property of software; it depends on the context and goals of its stakeholders. Hence, when you want to develop a high-quality software system, the first step must be a clear and precise specification of quality. Yet even if you get it right and complete, you can be sure that it will become invalid over time. So the only solution is continuous quality control: the steady and explicit evaluation of a product's properties with respect to its updated quality goals.This book guides you in setting up and running continuous quality control in your environment. Star

Latest status of the Japanese LCT coil and the domestic test facility

International Nuclear Information System (INIS)

Shimamoto, S.; Ando, T.; Hiyama, T.

1981-01-01

The Japan Atomic Energy Research Institute (JAERI), representing Japan, is now making one of six test coils for the International Energy Agency's (IEA) Large Coil Task(LCT). The Japanese LCT coil, which has a stored energy of 120 MJ, is based on a NgTi conductor, is pool-cooled, has a maximum field of 8T, and is edgewise, double-pancake wound, was completed in October, 1981. The LCT coil will be tested in the newly constructed domestic test facility up to its rated current in November, 1981, before transportation ORNL. The domestic test facility, which is composed of a cryogenic system a vacuum system, a power supply with protection system, and a data acqusition and control system, was completed and its performance measured at a new building for the LCT test at JSAERI in June, 1981. This paper describes the latest construction status of the Japanese LCT coil and the domestic test facility. The performance of the domestic test facility is described in this paper

Modeling and control for closed environment plant production systems

Science.gov (United States)

Fleisher, David H.; Ting, K. C.; Janes, H. W. (Principal Investigator)

2002-01-01

A computer program was developed to study multiple crop production and control in controlled environment plant production systems. The program simulates crop growth and development under nominal and off-nominal environments. Time-series crop models for wheat (Triticum aestivum), soybean (Glycine max), and white potato (Solanum tuberosum) are integrated with a model-based predictive controller. The controller evaluates and compensates for effects of environmental disturbances on crop production scheduling. The crop models consist of a set of nonlinear polynomial equations, six for each crop, developed using multivariate polynomial regression (MPR). Simulated data from DSSAT crop models, previously modified for crop production in controlled environments with hydroponics under elevated atmospheric carbon dioxide concentration, were used for the MPR fitting. The model-based predictive controller adjusts light intensity, air temperature, and carbon dioxide concentration set points in response to environmental perturbations. Control signals are determined from minimization of a cost function, which is based on the weighted control effort and squared-error between the system response and desired reference signal.

U.S. Strategic Command Chief Talks Deterrence, Partnerships During Latest SGL

OpenAIRE

Ochoa, Victoria

2017-01-01

Today@NPS The Naval Postgraduate School (NPS) welcomed U.S. Air Force Gen. John E. Hyten, Commander, U.S. Strategic Command (USSTRATCOM), for its latest Secretary of the Navy Guest Lecture (SGL), May 18 in King Auditorium. Hyten spoke about the importance of maintaining strategic deterrence and NPS' inclusion into the USSTRATCOM's Academic Alliance.

A framework for production control in health care organizations

NARCIS (Netherlands)

Vissers, Jan; Bertrand, J.W.M.; Vries, de G.

2001-01-01

The paper presents a hierarchical framework for production control of hospitals which deals with the balance between service and efficiency, at all levels of planning and control. The framework is based on an analysis of the design requirements for hospital production control systems. These design

Microbiological Quality Control of Probiotic Products

OpenAIRE

Astashkina, A.P.; Khudyakova, L.I.; Kolbysheva, Y.V.

2014-01-01

Microbiological quality control of probiotic products such as Imunele, Dannon, Pomogayka showed that they contain living cultures of the Lactobacillus Bifidobacterium genus in the amount of 107 CFU/ml, which corresponds to the number indicated on the label of products. It is identified that the survival rate of test-strains cultured with pasteurized products does not exceed 10%. The cell concentration of target-microorganisms was reduced by 20-45% after the interaction with living probiotic b...

Latest polarization and beam characterization results of the Orsay polarized electron source

International Nuclear Information System (INIS)

Arianer, J.; Cohen, S.; Essabaa, S.; Frascaria, R.; Zerhouni, O.

1995-01-01

The Orsay polarized electron source based on the chemi-ionization of aligned He(2 3 S 1 ) atoms and CO 2 molecules is briefly described. The latest results concerning electron polarization and beam emittance are presented. The present development status is also discussed. (K.A.)

Developing of milled peat production control in Turveruukki Oy

Energy Technology Data Exchange (ETDEWEB)

Ljokkoi, R

1985-01-01

Control research on the production of milled peat has as its primary aim the ability to control the peat drying process under different weather and field conditions. Actual development work connected with production control was begun in 1982 with the clear aim of developing and applying in practice a monitoring adn control system complete with measuring equipment which would permit the drying process to be measured indirectly and weather forecasts to be used systematically in the planning of production at each individual peat site. During the 1984 production season development work reached the stage of experimental use. Experiences gained from trial use have been mainly positive and trial use of the manual system can be considered the first step in the application o the system. As regards the measuring technique, it is justified to say that an adequate technical level has already been attained and the correlation of the indirect measuring method with peat drying can be further improved by adjusting the location height of the evaporation meter. On the other hand, calculation of the length of the harvesting cycle requires further research, which from the point of view of practice must be orientated towards control of field conditions and changes in them during the production season. Although the application of the production control system is informative in nature, it is clearly of assistance when deciding how to carry out production. By means of this system iy id possible to achieve financial benefit in the form of lowered production costs and a larger harvest per hectare.

Latest results from CERES/NA45

CERN Document Server

AUTHOR|(CDS)2074200; Adamova, D; Agakichiev, G; Appelshuser, H; Belaga, V; Braun-Munzinger, P; Campagnolo, R; Castillo, A; Cherlin, A; Damjanovic, S; Dietel, T; Dietrich, L; Drees, A; Esumi, S I; Filimonov, K; Fomenko, K; Fraenkel, Zeev; Garabatos, C; Glässel, P; Hering, G; Holeczek, J; Kushpil, V; Lenkeit, B C; Ludolphs, W; Maas, A; Marin, A; Messer, F; Milosevic, J; Milov, A; Mikowiec, D; Musa, L; Panebratsev, Yu A; Petchenova, O Yu; Petracek, V; Pfeiffer, A; Rak, J; Ravinovich, I; Rehak, P; Richter, M; Sako, H; Schmitz, W; Schükraft, J; Sedykh, S; Seipp, W; Sharma, A; Shimansky, S S; Slivova, J; Specht, H J; Stachel, J; Sumbera, M; Tilsner, H; Tserruya, Itzhak; Wienold, T; Windelband, B; Wurm, J P; Xie, W; Yurevich, S; Yurevich, V; Wessels, Johannes P.

2003-01-01

In this talk latest results from the analysis of $e^{+}e^{-}$ pairs emitted in Pb + Au collisions at 40 AGeV/c and a combined analysis of all data available at 158 AGeV/c are presented. The enhancement of low-mass $e^{+}e^{-}$ pairs $(m_{ee}>0.2 GeV/c^{2})$ with respect to the expected yield from hadron decays first reported at 158 AGeV/c is also found at 40 AGeV/c and is even larger there. Comparing to various theoretical models based on $\\pi^{+}\\pi^{-}$ annihilation, the data can only be reproduced, if the properties of the intermediate $\\rho$ in the hot and dense medium are modified. Theoretically, the modification is linked to baryon density rather than temperature. Constraints from hadron data taken at the same beam energies indeed indicate a fireball evolution along a trajectory of higher baryon density at 40 AGeV/c, consistent with the observed larger enhancement factor.

New Mid-Cretaceous (Latest Albian) Dinosaurs from Winton, Queensland, Australia

Science.gov (United States)

Hocknull, Scott A.; White, Matt A.; Tischler, Travis R.; Cook, Alex G.; Calleja, Naomi D.; Sloan, Trish; Elliott, David A.

2009-01-01

Background Australia's dinosaurian fossil record is exceptionally poor compared to that of other similar-sized continents. Most taxa are known from fragmentary isolated remains with uncertain taxonomic and phylogenetic placement. A better understanding of the Australian dinosaurian record is crucial to understanding the global palaeobiogeography of dinosaurian groups, including groups previously considered to have had Gondwanan origins, such as the titanosaurs and carcharodontosaurids. Methodology/Principal Findings We describe three new dinosaurs from the late Early Cretaceous (latest Albian) Winton Formation of eastern Australia, including; Wintonotitan wattsi gen. et sp. nov., a basal titanosauriform; Diamantinasaurus matildae gen. et sp. nov., a derived lithostrotian titanosaur; and Australovenator wintonensis gen. et sp. nov., an allosauroid. We compare an isolated astragalus from the Early Cretaceous of southern Australia; formerly identified as Allosaurus sp., and conclude that it most-likely represents Australovenator sp. Conclusion/Significance The occurrence of Australovenator from the Aptian to latest Albian confirms the presence in Australia of allosauroids basal to the Carcharodontosauridae. These new taxa, along with the fragmentary remains of other taxa, indicate a diverse Early Cretaceous sauropod and theropod fauna in Australia, including plesiomorphic forms (e.g. Wintonotitan and Australovenator) and more derived forms (e.g. Diamantinasaurus). PMID:19584929

New Mid-Cretaceous (latest Albian dinosaurs fromWinton, Queensland, Australia.

Directory of Open Access Journals (Sweden)

Scott A Hocknull

Full Text Available BACKGROUND: Australia's dinosaurian fossil record is exceptionally poor compared to that of other similar-sized continents. Most taxa are known from fragmentary isolated remains with uncertain taxonomic and phylogenetic placement. A better understanding of the Australian dinosaurian record is crucial to understanding the global palaeobiogeography of dinosaurian groups, including groups previously considered to have had Gondwanan origins, such as the titanosaurs and carcharodontosaurids. METHODOLOGY/PRINCIPAL FINDINGS: We describe three new dinosaurs from the late Early Cretaceous (latest Albian Winton Formation of eastern Australia, including; Wintonotitan wattsi gen. et sp. nov., a basal titanosauriform; Diamantinasaurus matildae gen. et sp. nov., a derived lithostrotian titanosaur; and Australovenator wintonensis gen. et sp. nov., an allosauroid. We compare an isolated astragalus from the Early Cretaceous of southern Australia; formerly identified as Allosaurus sp., and conclude that it most-likely represents Australovenator sp. CONCLUSION/SIGNIFICANCE: The occurrence of Australovenator from the Aptian to latest Albian confirms the presence in Australia of allosauroids basal to the Carcharodontosauridae. These new taxa, along with the fragmentary remains of other taxa, indicate a diverse Early Cretaceous sauropod and theropod fauna in Australia, including plesiomorphic forms (e.g. Wintonotitan and Australovenator and more derived forms (e.g. Diamantinasaurus.

Study of advanced control of ethanol production through continuous fermentation

Directory of Open Access Journals (Sweden)

AbdelHamid Ajbar

2017-01-01

Full Text Available This paper investigates the control of an experimentally validated model of production of bioethanol. The analysis of the open loop system revealed that the maximum productivity occurred at a periodic point. A robust control was needed to avoid instabilities that may occur when disturbances are injected into the process that may drive it toward or through the unstable points. A nonlinear model predictive controller (NLMPC was used to control the process. Simulation tests were carried out using three controlled variables: the ethanol concentration, the productivity and the inverse of the productivity. In the third configuration, the controller was required to seek the maximum operating point through the optimization capability built in the NLMPC algorithm. Simulation tests presented overall satisfactory closed-loop performance for both nominal servo and regulatory control problems as well as in the presence of modeling errors. The third control configuration managed to steer the process toward the existing maximum productivity even when the process operation or its parameters changed. For comparison purposes, a standard PI controller was also designed for the same control objectives. The PI controller yielded satisfactory performance when the ethanol concentration was chosen as the controlled variable. When, on the other hand, the productivity was chosen as the controlled output, the PI controller did not work properly and needed to be adjusted using gain scheduling. In all cases, it was observed that the closed-loop response suffered from slow dynamics, and any attempt to speed up the feedback response via tuning may result in an unstable behavior.

Latest research progress on food waste management: a comprehensive review

Science.gov (United States)

Zhu, Shangzhen; Gao, Hetong; Duan, Lunbo

2018-05-01

Since a large amount of food supplying is provided as a basic line measuring increasing residents’ life standard, food waste has become progressively numeral considerable. Much attention has been drawn to this problem. This work gave an overview on latest researches about anaerobic digestion, composting, generalized management and other developments on management of food waste. Different technologies were introduced and evaluated. Further views on future research in such a field were proposed.

Integrated production planning and control: A multi-objective optimization model

Directory of Open Access Journals (Sweden)

Cheng Wang

2013-09-01

Full Text Available Purpose: Production planning and control has crucial impact on the production and business activities of enterprise. Enterprise Resource Planning (ERP is the most popular resources planning and management system, however there are some shortcomings and deficiencies in the production planning and control because its core component is still the Material Requirements Planning (MRP. For the defects of ERP system, many local improvement and optimization schemes have been proposed, and improve the feasibility and practicality of the plan in some extent, but study considering the whole planning system optimization in the multiple performance management objectives and achieving better application performance is less. The purpose of this paper is to propose a multi-objective production planning optimization model Based on the point of view of the integration of production planning and control, in order to achieve optimization and control of enterprise manufacturing management. Design/methodology/approach: On the analysis of ERP planning system’s defects and disadvantages, and related research and literature, a multi-objective production planning optimization model is proposed, in addition to net demand and capacity, multiple performance management objectives, such as on-time delivery, production balance, inventory, overtime production, are considered incorporating into the examination scope of the model, so that the manufacturing process could be management and controlled Optimally between multiple objectives. The validity and practicability of the model will be verified by the instance in the last part of the paper. Findings: The main finding is that production planning management of manufacturing enterprise considers not only the capacity and materials, but also a variety of performance management objectives in the production process, and building a multi-objective optimization model can effectively optimize the management and control of enterprise

Optimising product recycling chains by control theory

NARCIS (Netherlands)

Kleineidam, U.; Lambert, A.J.D.; Blansjaar, J.; Kok, J.J.; Heijningen, van R.J.J.

2000-01-01

In this paper, a modelling method is described for production chains including recycling. It consists of elementary models of standard production operations, connected by market modules. The models are analysed using methods from control theory. These methods allow us to investigate essential

21 CFR 212.50 - What production and process controls must I have?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false What production and process controls must I have... DRUGS (Eff. 12-12-2011) Production and Process Controls § 212.50 What production and process controls must I have? You must have adequate production and process controls to ensure the consistent production...

Latest development in project site radwaste treatment facility (SRTF) Sanmen

International Nuclear Information System (INIS)

Mennicken, K.; Lohmann, P.

2015-01-01

Westinghouse Electric Germany GmbH (WEG) was successful in being awarded a contract as to the planning, delivery, installation and commissioning of radwaste treatment systems for the AP1000 units at Sanmen site, PR China. Operational low and intermediate level radioactive waste will be processed in the Site Radwaste Treatment Facility (SRTF). This paper explains the latest developments of the project, especially the experience with customer-hired Chinese planning partners, installation companies and Customer operating personnel. (authors)

Modelling and simulation SSM: latest state of the art technology

CSIR Research Space (South Africa)

Jahajeeah, N

2005-10-01

Full Text Available as one phase ? One Phase model ?Wider volume solid fraction 0 – 1 ? Implementation in Power Law Cut-Off Model (PLCO) of Procast Supporting the Manufacturing and Materials Industry in its quest for global competitiveness Assumptions of the PLCO Model... and Materials Industry in its quest for global competitiveness Modelling and Simulation SSM Latest state of the art technology N Jahajeeah Supporting the Manufacturing and Materials Industry in its quest for global competitiveness BEHAVIOUR OF THIXOTROPIC...

Advanced coking process control at Rautaruukki Steel

Energy Technology Data Exchange (ETDEWEB)

Ritamaki, O.; Luhtaniemi, H. [Rautaruukki Engineering (Finland)

1999-12-01

The paper presents the latest development of the Coking Process Management System (CPMS) at Raahe Steel. The latest third generation system is based on the previous system with the addition of fuzzy logic controllers. (The previous second generation system was based simultaneous feed forward and feedback control.) The system development has resulted in balanced coke oven battery heating, decreased variation in process regulation between shifts and increase of process information for operators. The economic results are very satisfactory. 7 figs.

The fungal and acritarch events as time markers for the latest Permian mass extinction: An update

Directory of Open Access Journals (Sweden)

Michael R. Rampino

2018-01-01

Full Text Available The latest Permian extinction (252 Myr ago was the most severe in the geologic record. On land, widespread Late Permian gymnosperm/seed-fern dominated forests appear to have suffered rapid and almost complete destruction, as evidenced by increased soil erosion and changes in fluvial style in deforested areas, signs of wildfires, replacement of trees by lower plants, and almost complete loss of peat-forming and fire-susceptible vegetation. Permian–Triassic boundary strata at many sites show two widespread palynological events in the wake of the forest destruction: The fungal event, evidenced by a thin zone with >95% fungal cells (Reduviasporonites and woody debris, found in terrestrial and marine sediments, and the acritarch event, marked by the sudden flood of unusual phytoplankton in the marine realm. These two events represent the global temporary explosive spread of stress-tolerant and opportunistic organisms on land and in the sea just after the latest Permian disaster. They represent unique events, and thus they can provide a time marker in correlating latest Permian marine and terrestrial sequences.

Latest results on b-physics from the ATLAS and CMS experiments

CERN Document Server

Pasqualucci, E; The ATLAS collaboration

2013-01-01

This paper briefly reviews some of the latest measurements of the ATLAS and CMS experiments at LHC in the b-physics sector, namely the ones on rare and semi-rare B0(s) decays, the parity violation in the b decay and the CP violation parameters in the Bs --> J/psi (μ+μ−)phi(K+K−) process, some of the measurements on heavy quarkonia systems.

Radioactive demonstration of DWPF product control strategy

International Nuclear Information System (INIS)

Andrews, M.K.; Bibler, N.E.

1994-01-01

The Defense Waste Processing Facility at the Savannah River Site (SRS) will vitrify high-level nuclear waste into borosilicate glass. The waste will be mixed with properly formulated glass-making frit and fed to a melter at 1150 degrees C. Process reliability and product quality are ensured by proper control of the melter feed composition. The effectiveness of the product and process control strategies that will be utilized by the Defense Waste Processing Facility (DWPF) was demonstrated during a campaign in the Shielded Cells Facility of the Savannah River Technology Center (SRTC). The remotely operated process included the preparation of the melter feed, vitrification in a slurry-fed 1/100th scale melter an analysis of the glass product both for its composition an durability. The campaign processed approximately 10 kg (on a dry basis) of radioactive sludge from Tank 51. This sludge is representative of the first batch of sludge that will be sent to the DWPF for immobilization into borosilicate glass. Additions to the sludge were made based on calculations using the Product Composition Control System (PCCS). Analysis of the glass produced during the campaign showed that a durable glass was produced with a composition very close to that predicted using the PCCS. 10 refs., 4 tabs

IMPLEMENTATION OF CONTROL CARDS AND SUPPORTING METHOD IN PRODUCTION ENGINEERING

Directory of Open Access Journals (Sweden)

Anna WOLNOWSKA

2012-10-01

Full Text Available In the article there were presented chosen method associated with statistical control of production processes. Mainly focused on control cards and Pareto‐Lorenz analysis. Showed method were implemented to analysis production process stability of hearing aids in X company (the brand name don’t give because date of production is secret. Researches were made few months after new assembly lines starts‐up. Main aim of researches was defects types identification occurred in production process and determine the scale of effect. Finally received results were satisfactory, i.e. despite of occurred errors, control cards analysis showed that production process of BTE‐type (Behind‐The‐Ear hearing aids was stable.

Review of Residential Comfort Control Products and Opportunities

Energy Technology Data Exchange (ETDEWEB)

Metzger, Cheryn E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Goyal, Siddharth [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Baechler, Michael C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-12-15

This paper begins by discussing the interaction of each major component in advanced sensor and control applications related to HVAC equipment. The paper also looks at the applications of these components to commissioning, maintenance and operations of the HVAC equipment in residential buildings. A summary of state-of-the-art product features is also provided. These products are categorized through their primary application type (commissioning/maintenance or operation) and the features are categorized by component type (sensors, data storage, human-in-the-loop, communication, and controls). A common theme that emerges from this study is the importance of the ability for various product categories to be connected to each other. There are many manufacturers of sensors and many manufacturers of controls, but the power to automate any commissioning, maintenance or operation application, requires connectivity.

Latest AMS Results on elementary particles in cosmic rays

Science.gov (United States)

Kounine, Andrei; AMS Collaboration

2017-01-01

AMS-02 is a particle physics detector collecting data on the International Space Station since May 2011. Precision measurements of all elementary charged cosmic ray particles have been performed by AMS using a data sample of 85 billion cosmic ray events collected during the first five years of operations on the Station. The latest AMS results on the fluxes and flux ratios of the elementary cosmic ray particles are presented. They show unique features that require accurate theoretical interpretation as to their origin, be it from dark matter collisions or new astrophysical sources. On behalf of the AMS Collaboration.

Operation and Control of Enzymatic Biodiesel Production

DEFF Research Database (Denmark)

Price, Jason Anthony; Huusom, Jakob Kjøbsted; Nordblad, Mathias

This work explores the control of biodiesel production via an enzymatic catalyst. The process involves the transesterification of oils/fats with an alcohol (usually methanol or ethanol), using enzymatic catalysts to generate mono-alkyl esters (the basis of biodiesel) and glycerol as by......-product. Current literature indicates that enzymatic processing of oils and fats to produce biodiesel is technically feasible and developments in immobilization technology indicate that enzyme catalysts can become cost effective compared to chemical processing. However, with very few exceptions, enzyme technology...... is not currently used in commercial-scale biodiesel production. This is mainly due to non-optimized process designs, which do not use the full potential of the catalysts in a cost-efficient way. Furthermore is it unclear what process variables need to be monitored and controlled to ensure optimal economics...

Internal cost control on the ecological quality of products

Directory of Open Access Journals (Sweden)

N.P. Syroid

2018-04-01

Full Text Available To improve the environmental quality of products due attention should be paid to control the processes related to environmental quality input of the product. The results of the study help to state the purpose and objectives of the control, also to define objects for internal control of operations cost of environmental quality. So, we believe that the main purpose of internal cost control on the ecological quality of products is the establishment of the correctness and legality of business operations, prevention of violations and abuses in the expenditure of natural, labour, material and financial resources to ensure the minimization of negative impact on the health of consumers and the environment. The basic objectives of internal control of expenditure are brought forward, but it should be noted that they can vary and depend on the size, structure, spheres and types of economic activity of the enterprise, the requirements of management personnel. In the process of identifying the objects of control of environmental quality it should be noted that this list is not exhaustive, but it is most relevant to highlight objects such as genetically modified organisms and waste production. Also the subjects of cost control to environmental quality, their functions and the information base for monitoring are determined. Proper organization of the process of internal cost control on the ecological quality of products would benefit from a clear documentation of transactions, timely and complete registration of accounting data in the registers, the true reflection of information in managerial financial reporting and ensure reduction of the negative impact on the health of consumers and the environment.

Radiological control of food importation products; Control radiologico de productos alimenticios de importacion

Energy Technology Data Exchange (ETDEWEB)

Aguirre G, J. [CNSNS, Dr. Barragan 779, 03020 Mexico D.F. (Mexico)]. e-mail: jaguirre@cnsns.gob.mx

2003-07-01

Nowadays exists the possibility of marketing products possibly polluted with radioactive isotopes, by that some countries like Mexico, they have been given to the task of creating legal bases and the necessary infrastructure with the end of carrying out the radiological surveillance of nutritious import products. In this work the legal bases that our country has established for the radiological control are presented besides the results of this radiological control carried out through the gamma spectroscopy analysis of nutritious import products sent to our country through diverse companies that import foods produced mainly in European countries. (Author)

School Issues Under [Section] 504 and the ADA: The Latest and Greatest.

Science.gov (United States)

Aleman, Steven R.

This paper highlights recent guidance and rulings from the Office of Civil Rights (OCR) of interest to administrators, advocates, and attorneys. It is a companion piece to Student Issues on SectionNB504/ADA: The Latest and Greatest. Compliance with SectionNB504 and the Americans with Disabilities Act (ADA) continues to involve debate and dialog on…

LATEST TOURNAISIAN (EARLY CARBONIFEROUS CONODONTS FROM THE TABAI LIMESTONE, TIRAH, NORTHWESTERN PAKISTAN

Directory of Open Access Journals (Sweden)

FAZL-I-RABBI KHAN

2004-11-01

Full Text Available A new stratigraphic unit, the Tabai Limestone of the poorly known Tirah area of northwest Pakistan, is one of several Early Carboniferous carbonate units distributed along the North Gondwana margin, some connected with transgressive interludes. The Tabai Limestone has produced latest Tournaisian (Early Carboniferous conodonts indicative of the middle of the anchoralis-latus Zone.

Production planning and control of less emitting production systems

Energy Technology Data Exchange (ETDEWEB)

Haasis, H.D. [Bremen Univ. (Germany)

1995-12-31

The concept of integral environmental protection has been growing in importance within Western Europe in recent years. Increasingly, it has come to be recognized that no one part of the environment is separate from any other, it functions as a whole. Yet, pollution control was until recently, usually based on an approach which considers emissions to air, water, and land separately. That has begun to change, particularly since the 1987 report by the World Commission on Environment and Development. This can be recognized, for example, within the proposal for a Directive of the Council of the European Union on Integrated Pollution Prevention and Control. By this, the environmental media are placed on an equal legislative footing so that the final result will be that the way in which an installation is operated will be better for the whole environment. In other words, less emission production systems are obtained. Realization of an integral concept or of less emission production systems initially requires technical measures for the avoidance and the minimization of emissions, as well as recovery and recycling of materials and substances

Production planning and control of less emitting production systems

Energy Technology Data Exchange (ETDEWEB)

Haasis, H D [Bremen Univ. (Germany)

1996-12-31

The concept of integral environmental protection has been growing in importance within Western Europe in recent years. Increasingly, it has come to be recognized that no one part of the environment is separate from any other, it functions as a whole. Yet, pollution control was until recently, usually based on an approach which considers emissions to air, water, and land separately. That has begun to change, particularly since the 1987 report by the World Commission on Environment and Development. This can be recognized, for example, within the proposal for a Directive of the Council of the European Union on Integrated Pollution Prevention and Control. By this, the environmental media are placed on an equal legislative footing so that the final result will be that the way in which an installation is operated will be better for the whole environment. In other words, less emission production systems are obtained. Realization of an integral concept or of less emission production systems initially requires technical measures for the avoidance and the minimization of emissions, as well as recovery and recycling of materials and substances

Preliminary Screening of Potential Control Products against Drosophila suzukii

Directory of Open Access Journals (Sweden)

Andrew G. S. Cuthbertson

2014-06-01

Full Text Available The first recording of Drosophila suzukii in the UK occurred in the south of England during August 2012. Since then sticky traps have continued to record the presence of individuals. Several products (both chemical and biological were investigated for their efficacy against different life-stages of the pest. Both direct and indirect exposure to control products was assessed. Spinosad, chlorantraniliprole and the experimental product, TA2674, showed excellent potential as control agents when used as either a pre- or post-dipping treatment for blueberries with mortalities of 100%, 93% and 98% mortality, respectively, being achieved following pre-treatment. Direct spray application of all products tested had limited impact upon adult flies. Highest mortality (68% was achieved following direct application of TA2674. Entomopathogenic agents (nematodes and fungi tested appeared to reduce fly population development (ranges of 34–44% mortality obtained but would seem unable to eradicate outbreaks. The potential of the tested products to control D. suzukii is discussed.

A modelling and control structure for product quality control in climate-controlled processing of agro-material

NARCIS (Netherlands)

Verdijck, G.J.C.; Straten, van G.

2002-01-01

In this paper a modelling and control structure for product quality control is presented for a class of operations that processes agro-material. This class can be characterised as climate-controlled operations, such as storage, transport and drying. The basic model consists of three parts. These are

Production, control and utilization of radioisotopes including radiopharmaceuticals

International Nuclear Information System (INIS)

Muenze, R.

1985-05-01

From April 29th to May 5th, 1984 27 participants from 21 developing countries stayed within an IAEA Study Tour ('Production, Control and Utilization of Radioisotopes including Radiopharmaceuticals') in the GDR. In the CINR, Rossendorf the reactor, the cyclotron, the technological centre as well as the animal test laboratory were visited. The participants were made familiar by 10 papers with the development, production and control of radiopharmaceuticals in the CINR, Rossendorf. (author)

Cordyceps fungi: natural products, pharmacological functions and developmental products.

Science.gov (United States)

Zhou, Xuanwei; Gong, Zhenghua; Su, Ying; Lin, Juan; Tang, Kexuan

2009-03-01

Parasitic Cordyceps fungi, such as Cordyceps sinensis, is a parasitic complex of fungus and caterpillar, which has been used for medicinal purposes for centuries particularly in China, Japan and other Asian countries. This article gives a general idea of the latest developments in C. sinensis research, with regard to the active chemical components, the pharmacological effects and the research and development of products in recent years. The common names for preparations include DongChongXiaCao in Chinese, winter worm summer grass in English. It has many bioactive components, such as 3'-deoxyadenosine, cordycepic acid and Cordyceps polysaccharides. It is commonly used to replenish the kidney and soothe the lung, and for the treatment of fatigue. It also can be used to treat conditions such as night sweating, hyposexuality, hyperglycaemia, hyperlipidaemia, asthenia after severe illness, respiratory disease, renal dysfunction, renal failure, arrhythmias and other heart disease and liver disease. Because of its rarity and outstanding curative effects, several mycelia strains have been isolated from natural Cordyceps and manufactured by fermentation technology, and are commonly sold as health food products. In addition, some substitutes such as C. militaris and adulterants also have been used; therefore, quality control of C. sinensis and its products is very important to ensure their safety and efficacy. Recent research advances in the study of Cordyceps, including Cordyceps mushrooms, chemical components, pharmacological functions and developmental products, has been reviewed and discussed. Developing trends in the field have also been appraised.

A socio-technical approach for the design of a production control system : towards controllable production units

NARCIS (Netherlands)

Slomp, Jannes; Ruël, Gwenny C.

2000-01-01

In the design of a production control system much attention is usually paid to technicalaspects, whereas the elaboration upon social aspects remain underexposed. SociotechnicalSystems Theory (SST) emphasizes the importance of finding a joint optimization between the technical and the social systems

Engineering Documentation Control Handbook Configuration Management and Product Lifecycle Management

CERN Document Server

Watts, Frank B

2011-01-01

In this new edition of his widely-used Handbook, Frank Watts, widely recognized for his significant contributions to engineering change control processes, provides a thoroughly practical guide to the implementation and improvement of Engineering Documentation Control (EDC), Product Lifecycle Management and Product Configuration Management (CM). Successful and error-free implementation of EDC/CM is critical to world-class manufacturing. Huge amounts of time are wasted in most product manufacturing environments over EDC/CM issues such as interchangeability, document release and change control -

A guide for controlling consumer products containing radioactive substances

International Nuclear Information System (INIS)

1985-01-01

Consumer products are considered regardless of the purpose for which the radionuclide is added. For example, the purpose may be to make use of the ionising radiation emitted by the substance in the product itself (e.g. radioluminescent devices antistatic devices and ionisation chamber smoke detectors), or to make use of some other property of the material where the presence of radiation in the final product is merely adventitious (e.g. thorium gas mantles, ceramics with uranium glazes, and products containing radioactive tracers added to facilitate manufacturing and inspection processes). The Guide does not cover some products containing natural radioactive substances which have not been intentionally added, such as building materials. The Guide does not cover medicinal products and pharmaceuticals, nuclear powered cardiac pacemakers, or electronic equipment, such as television receivers, that emit X-rays. Unlike the 1970 Guide, this Guide does not consider those products, such as EXIT signs, containing gaseous tritium light sources, that would not be supplied directly to members of the public. The Guide is concerned mainly with the exposure arising from consumer products of those persons who are not subject to any regulatory controls for purposes of radiation protection in normal circumstances. Members of the public come under this heading, but not workers involved in the manufacture of consumer products. These workers will normally be subject to separate control. Radiological protection concepts and policy for the control of radioactive consumer products and licensing and post-licensing surveillance are developed

Globanomalina luxorensis, a Tethyan biostratigraphic marker of latest Paleocene global events

OpenAIRE

Speijer, Robert; Samir, AM

1997-01-01

The lowest common occurrence (LCO) of the planktonic foraminifera Globanomalina luxorensis marks the level of the latest Paleocene global benthic extinction event (BEE) and associated negative delta(13) C excursion in various bathyal and neritic successions in the Mediterranean region. Below the BEE level, G. luxorensis is extremely rare and subordinate in abundance relative to its precursor G, chapmani. From this level onwards, G. luxorensis generally constitutes a large proportion of the pl...

Current status of electron beam processing applications and the latest accelerator technologies in Japan

International Nuclear Information System (INIS)

Hoshi, Yasuhisa

1998-01-01

Electron Beam (EB) processing has been increasing in popularity as a cross-linking process since the beginning of its industrial use. Examples are heat resistance improvement of electric wires, high quality foamed polyethylene (PE) and polypropylene (PP), automotive tire manufacturing and heat shrinkable products. EB is also used in the tire manufacturing process as a pre-vulcanisation of rubber sheet before forming process. Cross-linking of electric wire insulators is the most popular industrial application of electron beam accelerators in Japan. EB cross-linked wires are widely used in electrical appliances and automotive wire harnesses. Curing of inks or coating is a promising application of low energy EB. EB cure is often compared with Ultra-Violet (UV) curing. Both has a common advantage compared with a conventional heat curing process such as no solvent requirement. A typical advantage is that no initiators are required to start curing process. EB can also be used to remove SO 2 and NO x from coal flue gas. This paper reports some of these applications and discusses the latest equipment design. (author)

Will marine productivity wane?

Science.gov (United States)

Laufkötter, Charlotte; Gruber, Nicolas

2018-03-01

If marine algae are impaired severely by global climate change, the resulting reduction in marine primary production would strongly affect marine life and the ocean's biological pump that sequesters substantial amounts of atmospheric carbon dioxide in the ocean's interior. Most studies, including the latest generation of Earth system models, project only moderate global decreases in biological production until 2100 (1, 2), suggesting that these concerns are unwarranted. But on page 1139 of this issue, Moore et al. (3) show that this conclusion might be shortsighted and that there may be much larger long-term changes in ocean productivity than previously appreciated.

Radioactive demonstration of DWPF product control strategy

International Nuclear Information System (INIS)

Andrews, M.K.; Bibler, N.E.

1992-01-01

The effectiveness of the product and process control strategies that will be utilized by the Defense Waste Processing Facility (DWPF) was demonstrated during a campaign in the Shielded Cells Facility (SCF) of the Savannah River Technology Center (SRTC). The remotely operated process included the preparation of the melter feed, vitrification in a slurry-fed 1/100th scale melter and analysis of the glass product both for its composition and durability. The campaign processed approximately 10 kg (on a dry basis) of radioactive sludge from Tank 51. This sludge is representative of the first batch of sludge that will be sent to the DWPF for immobilization into borosilicate glass. Additions to the sludge were made based on calculations using the Product Composition Control System (PCCS). Analysis of the glass produced during the campaign showed that a durable glass was produced with a composition similar to that predicted using the PCCS

Heavy flavour hadro-production cross-sections

CERN Document Server

Wöhri, H K

2003-01-01

Hadro-production data on charm and beauty absolute cross-sections, collected by experiments at CERN, DESY and Fermilab, are reviewed. The measurements, corrected for the 'time evolution' of the branching ratios, are compared to calculations done with Pythia, as a function of the collision energy, using the latest parametrizations of the parton densities. We then estimate some charm and beauty production cross-sections relevant for future measurements, including nuclear effectes in the PDFs. We finish by briefly addressing the relevance, in heavy-ion collisions, of beauty production as feed-down for J/psi production.

Dynamitron control systems

International Nuclear Information System (INIS)

Lisanti, Thomas F.

2005-01-01

The Dynamitron control system utilizes the latest personal computer technology in control circuitry and components. Both the DPC-2000 and newer Millennium series of control systems make use of their modular architecture in both software and hardware to keep up with customer and engineering demands. This also allows the main structure of the software to remain constant for the user while software drivers are easily changed as hardware demands are modified and improved. The system is presented as four units; the Remote I/O (Input/Output), Local Analog and Digital I/O, Operator Interface and the Main Computer. The operator is provided with a selection of many informative screen displays. The control program handles all graphic screen displays and the updating of these screens directly; it does not communicate to a display terminal. This adds to the quick response and excellent operator feedback received while operating the accelerator. The CPU also has the ability to store and record all process variable setpoints for each product that will be treated. All process parameters are printed to a report at regular intervals during a process run for record keeping

Modular products: Smartphone design from a circular economy perspective

OpenAIRE

Schischke, Karsten; Proske, Marina; Nissen, Nils F.; Lang, Klaus-Dieter

2016-01-01

Currently a range of modular smartphones is emerging, including the Fairphone 2, Puzzlephone, Google's Project ARA, RePhone, LG's G5 and others. In an industry of perceived short product cycles a modular design concept might become crucial for longer product lifetimes. The paper provides an overview on latest product developments and assesses these against environmental criteria, including longevity, durability, upgradeability, repairability and Design for Recycling and Reuse. Modular product...

Latest improvements on TRACPWR six-equations thermohydraulic code

International Nuclear Information System (INIS)

Rivero, N.; Batuecas, T.; Martinez, R.; Munoz, J.; Lenhardt, G.; Serrano, P.

1999-01-01

The paper presents the latest improvements on TRACPWR aimed at adapting the code to present trends on computer platforms, architectures and training requirements as well as extending the scope of the code itself and its applicability to other technologies different from Westinghouse PWR one. Firstly major features of TRACPWR as best estimate and real time simulation code are summed, then the areas where TRACPWR is being improved are presented. These areas comprising: (1) Architecture: integrating TRACPWR and RELAP5 codes, (2) Code scope enhancement: modelling the Mid-Loop operation, (3) Code speed-up: applying parallelization techniques, (4) Code platform downswing: porting to Windows N1 platform, (5) On-line performance: allowing simulation initialisation from a Plant Process Computer, and (6) Code scope extension: using the code for modelling VVER and PHWR technology. (author)

Latest NASA Instrument Cost Model (NICM): Version VI

Science.gov (United States)

Mrozinski, Joe; Habib-Agahi, Hamid; Fox, George; Ball, Gary

2014-01-01

The NASA Instrument Cost Model, NICM, is a suite of tools which allow for probabilistic cost estimation of NASA's space-flight instruments at both the system and subsystem level. NICM also includes the ability to perform cost by analogy as well as joint confidence level (JCL) analysis. The latest version of NICM, Version VI, was released in Spring 2014. This paper will focus on the new features released with NICM VI, which include: 1) The NICM-E cost estimating relationship, which is applicable for instruments flying on Explorer-like class missions; 2) The new cluster analysis ability which, alongside the results of the parametric cost estimation for the user's instrument, also provides a visualization of the user's instrument's similarity to previously flown instruments; and 3) includes new cost estimating relationships for in-situ instruments.

Environmental control technology in petroleum drilling and production

International Nuclear Information System (INIS)

Wojtanowicz, A.K.

1997-01-01

Environmental control technology (ECT) is process integrated and relates mainly to pollution prevention and risk assessment. Mechanisms of environmental impact in petroleum drilling, well completion and production, include the generation of waste, induction of toxicity or the creation of pathways for pollutant migration. The identification and evaluation of these mechanisms constitute two parts of the scope of ECT. A third part is the development of new techniques to comply with environmental requirements without prejudicing productivity. The basic concepts of the ECT approach are presented in this chapter. The approach is then used to analyse oilfield drilling and production processes. Environmental control components developed in these technologies are described. These include: the control of the volume and toxicity of drilling fluids; source separation technology in produced water cleaning; subsurface injection of oilfield waste slurries; containment technology in the integrity of petroleum wells; subsurface reduction of produced water; oilfield pit closure technology. (37 figures; 26 tables; 227 references) (UK)

Control of Listeria monocytogenes in food production plants

Directory of Open Access Journals (Sweden)

Dimitrijević Mirjana

2008-01-01

Full Text Available L. monocytogenes has been established in different plants for the production of food, including dairy plants, abattoirs, plants for the processing of fish, as well as those for the production of ready-to-eat (RTE food and this fact is being considered as the primary mechanism of food contamination with this bacteria. There is also the factor of numerous and diverse contaminated production equipment, because it has certain parts that are inaccessible for the necessary cleaning and disinfection. The temperature, position, as well as the material of the work surface are also linked to the contamination of plants with this bacteria. Investigations carried out so far have helped toward the better understanding of the manner and time of contamination of food items in the course of the production process, but there are still unresolved problems, including most certainly the biggest one - the adherence of bacteria and the creation of a biofilm, when the bacteria is in that condition more resistant to so-called stress factors which are usually used in the food industry for the purpose of decontamination of the surfaces with which foods come into contact. The control of L. monocytogenes in food production plants is possible primarily by using an integrated programme, compatible with the systems Hazard Analysis Critical Control Point (HACCP and Good Hygiene Practice (GHP, necessary in the production of food that is safe for the consumer. Essentially, the control measures that can contribute to reducing the incidence of findings of L.monocytogenes in the finished product, as well as the reducing of the level of contamination with this bacteria are linked, on the one hand, with hygiene procedures in the production process, and, on the other, with the applied technological procedures.

Performance of the latest MPPCs with reduced dark counts and improved photon detection efficiency

International Nuclear Information System (INIS)

Tsujikawa, T.; Funamoto, H.; Kataoka, J.; Fujita, T.; Nishiyama, T.; Kurei, Y.; Sato, K.; Yamamura, K.; Nakamura, S.

2014-01-01

We have tested the performance of two types of the latest Multi-Pixel Photon Counters (MPPCs; measuring 3×3 mm 2 in size) developed by Hamamatsu Photonics K.K. The new S12572-050C is a successor to the S10362-33-050C (i.e., conventional 3×3-mm 2 pixel MPPC of 50 μm pitch), comprises 3600 Geiger mode avalanche photodiodes (APDs), and also features high gain (up to 1.25×10 6 ), a low dark count (up to 10 6 cps), and improved photon detection efficiency (PDE) by up to 30%. The S12572-015C is a new type of fine-pitch (15 μm) MPPC featuring a wide dynamic range and fast timing response. This paper first presents the detailed performance of these latest MPPCs as photon counting devices. It then describes our fabrication of a prototype detector consisting of a MPPC optically coupled with a Ce:GAGG scintillator. We obtained average FWHM energy resolutions of 7.3% (15 μm) and 6.7% (new-50 μm), as compared to 6.9% (old-50 μm) for 662-keV gamma rays from the 137 Cs source, as measured at 20 °C. Moreover, the number of fired pixels for 662-keV gamma rays increased by 30% for the new-50 μm (as compared to the old-50 μm). We confirmed that the low energy threshold improved from 10 keV to 4 keV, when using the latest MPPC device (new-50 μm). We also confirmed that the timing resolution of the new MPPC is 50 ps or even better, as compared to 89 ps of the old MPPC. The results thus confirm that these new types of MPPCs are promising for various applications as scintillation detectors. - Highlights: • We tested the performance of the latest MPPC. • We confirmed that the new MPPC is superior to the old MPPC. • We plan to apply the new MPPC for a next-generation PET and a handy Compton camera

Performance of the latest MPPCs with reduced dark counts and improved photon detection efficiency

Energy Technology Data Exchange (ETDEWEB)

Tsujikawa, T., E-mail: takayuki-t.w@asagi.waseda.jp [Research Institute for Science and Engineering, Waseda University, 3-4-1, Ohkubo, Shinjuku, Tokyo (Japan); Funamoto, H.; Kataoka, J.; Fujita, T.; Nishiyama, T.; Kurei, Y. [Research Institute for Science and Engineering, Waseda University, 3-4-1, Ohkubo, Shinjuku, Tokyo (Japan); Sato, K.; Yamamura, K.; Nakamura, S. [Solid State Division, Hamamatsu Photonics K. K., 1126-1, Ichino-cho, Hamamatsu, Shizuoka (Japan)

2014-11-21

We have tested the performance of two types of the latest Multi-Pixel Photon Counters (MPPCs; measuring 3×3 mm{sup 2} in size) developed by Hamamatsu Photonics K.K. The new S12572-050C is a successor to the S10362-33-050C (i.e., conventional 3×3-mm{sup 2} pixel MPPC of 50 μm pitch), comprises 3600 Geiger mode avalanche photodiodes (APDs), and also features high gain (up to 1.25×10{sup 6}), a low dark count (up to 10{sup 6} cps), and improved photon detection efficiency (PDE) by up to 30%. The S12572-015C is a new type of fine-pitch (15 μm) MPPC featuring a wide dynamic range and fast timing response. This paper first presents the detailed performance of these latest MPPCs as photon counting devices. It then describes our fabrication of a prototype detector consisting of a MPPC optically coupled with a Ce:GAGG scintillator. We obtained average FWHM energy resolutions of 7.3% (15 μm) and 6.7% (new-50 μm), as compared to 6.9% (old-50 μm) for 662-keV gamma rays from the {sup 137}Cs source, as measured at 20 °C. Moreover, the number of fired pixels for 662-keV gamma rays increased by 30% for the new-50 μm (as compared to the old-50 μm). We confirmed that the low energy threshold improved from 10 keV to 4 keV, when using the latest MPPC device (new-50 μm). We also confirmed that the timing resolution of the new MPPC is 50 ps or even better, as compared to 89 ps of the old MPPC. The results thus confirm that these new types of MPPCs are promising for various applications as scintillation detectors. - Highlights: • We tested the performance of the latest MPPC. • We confirmed that the new MPPC is superior to the old MPPC. • We plan to apply the new MPPC for a next-generation PET and a handy Compton camera.

Quality control of static irradiation processing products

International Nuclear Information System (INIS)

Bao Jianzhong; Chen Xiulan; Cao Hong; Zhai Jianqing

2002-01-01

Based on the irradiation processing practice of the nuclear technique application laboratory of Yangzhou Institute of Agricultural Science, the quality control of irradiation processing products is discussed

The role of production control in the development of burnout.

Science.gov (United States)

Houben, G J; Nijhuis, F J

1996-01-01

Burnout is an increasingly important problem in modern work organizations. Few studies, however, have explicitly applied an adequate theoretical understanding of the performance of modern organizations. This article aims to initiate both a discussion of this phenomenon and higher-quality research into the emergence of burnout based on an understanding of the economic-technological rationalization and control (management control) of production and service processes. In applying production control, both technical and bureaucratic, group and attitudinal control systems are increasingly integrated. This so-called systematic control strategy is one of the major causes of burnout. The cumulative effect of an increasing workload combined with reduced resources due to economic considerations and technocratic implementation of production control is assumed to be relevant to the development of burnout. The authors' propositions apply to service workers in human service organizations and to key workers in enterprises using flexible specialization combined with self-directed work groups.

Testing controlled productive knowledge of adverb-verb collocations ...

African Journals Online (AJOL)

The study also reveals that controlled productive knowledge of adverbverb collocations is less problematic. Based on these results, teaching strategies aimed at improving the use of adverb-verb collocations among EFL users are proposed. Keywords: academic writing, adverb-verb collocations, productive knowledge of ...

Method for ph-controlled fermentation and biogas production

DEFF Research Database (Denmark)

2014-01-01

The present invention is in the field of biomass processing and bioenergy production and facilitates efficient biomass processing and an increased production of renewable energy from processing and anaerobic fermentation of a wide variety of organic materials. In order to control the pH value...

46 CFR 164.019-13 - Production quality control requirements.

Science.gov (United States)

2010-10-01

... establish procedures for maintaining quality control of the materials used in production, manufacturing... place of manufacture unless alternate procedures have been accepted by the Commandant. (c) Production... manufactured. A new lot must be started whenever any change is made in materials, design, or production method...

Zika virus: the latest newcomer

Directory of Open Access Journals (Sweden)

Juan-Carlos eSaiz

2016-04-01

Full Text Available Since the beginning of this century, humanity has been facing a new emerging, or re-emerging, virus threat almost every year: West Nile, Influenza A, avian flu, dengue, Chikungunya, SARS, MERS, Ebola, and now Zika, the latest newcomer. Zika virus (ZIKV, a flavivirus transmitted by Aedes mosquitoes, was identified in 1947 in a sentinel monkey in Uganda, and later on in humans in Nigeria. The virus was mainly confined to the African continent until it was detected in south-east Asia the 1980´s, then in the Micronesia in 2007 and, more recently in the Americas in 2014, where it has displayed an explosive spread, as advised by the World Health Organization (WHO, which resulted in the infection of hundreds of thousands of people. ZIKV infection was characterized by causing a mild disease presented with fever, headache, rash, arthralgia, and conjunctivitis, with exceptional reports of an association with Guillain-Barre syndrome (GBS and microcephaly. However, since the end of 2015, an increase in the number of GBS associated cases and an astonishing number of microcephaly in foetus and new-borns in Brazil have been related to ZIKV infection, raising serious worldwide public health concerns. Clarifying such worrisome relationships is, thus, a current unavoidable goal. Here, we extensively review what is currently known about ZIKV, from molecular biology, transmission routes, ecology and epidemiology, to clinical manifestations, pathogenesis, diagnosis, prophylaxis and public health.

Latest developments in GaN-based quantum devices for infrared optoelectronics

OpenAIRE

Monroy, Eva; Guillot, Fabien; Leconte, Sylvain; Nevou, Laurent; Doyennette, Laeticia; Tchernycheva, Maria; Julien, François H.; Baumann, Esther; Giorgetta, Fabrizio R.; Hofstetter, Daniel

2011-01-01

In this work, we summarize the latest progress in intersubband devices based on GaN/AlN nanostructures for operation in the near-infrared. We first discuss the growth and characterization of ultra-thin GaN/AlN quantum well and quantum dot superlattices by plasma-assisted molecular-beam epitaxy. Then, we present the performance of nitride-based infrared photodetectors and electro-optical modulators operating at 1.55 μm. Finally, we discuss the progress towards intersubband light emitters, incl...

Interaction effect of psychological distress and asthma control on productivity loss?

Science.gov (United States)

Moullec, Grégory; FitzGerald, J Mark; Rousseau, Roxanne; Chen, Wenjia; Sadatsafavi, Mohsen

2015-06-01

Little is known about the potential synergistic effect of comorbid psychological distress (PD) and uncontrolled asthma (UA) on productivity loss. We estimated the productivity loss associated with the combination of these two potentially preventable conditions in employed adults with asthma. A population-based random sample of 300 adults with asthma in British Columbia, Canada, was prospectively recruited between Dec 2010 and Aug 2012. PD and productivity loss due to absenteeism and presenteeism was measured using validated instruments, and asthma control was ascertained using 2010 Global Initiative for Asthma management strategy. We used two-part regression models to study the contribution of UA and PD to productivity loss. Compared with reference group (controlled asthma (CA)+noPD), those with UA+noPD had CAD$286 (95%CI $276-297) weekly productivity loss, and those with CA+PD had CAD$465 ($445-485). Those with UA+PD had CAD$449 (437-462) in productivity loss. There was no significant interaction effect of PD with asthma control levels on productivity loss (p=0.22). In patients without PD, uncontrolled asthma was associated with a higher productivity loss than controlled asthma, but this was not the case in patients with PD. This finding can be explained by the fact that the contribution of PD to productivity loss is so large that there is no room for synergy with asthma control. Future studies should assess the impact of interventions that modify PD in patients with asthma. Copyright ©ERS 2015.

7 CFR 58.149 - Alternate quality control programs for dairy products.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Alternate quality control programs for dairy products... for dairy products. (a) When a plant has in operation an acceptable quality control program which is... (CONTINUED) REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS...

Developing Product Quality Control for Standardization of Tsetse Mass Production. Working Material

International Nuclear Information System (INIS)

2002-01-01

The recent Pan-African Tsetse and Trypanosomosis Eradication Campaign (PATTEC) provides a mechanism within which SIT will be one of the major components of an integrated areawide approach to the establishment of tsetse fly-free areas. Currently world-wide tsetse production is 1/40 of the projected requirement in 2006. To achieve this objective it is essential that quality control (QC) measures suitable for the expanded production be in place. Therefore, improved QC methodology has become a top priority. Improvements in QC methodology will help to ensure the attainment of these production goals and improve quality of rearing, minimize production costs and generate trained QC and production staff required to successfully produce flies and monitor their quality and suitability for release. The proposed CRP is designed to address these issues.

21 CFR 226.40 - Production and control procedures.

Science.gov (United States)

2010-04-01

...) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR TYPE A MEDICATED ARTICLES Product Quality Control... event of any significant discrepancies, key personnel shall prevent distribution of the batch in... control procedures shall include provision for discontinuing distribution of any Type A medicated article...

A STUDY PAPER HOW LATEST TECHNOLOGIES LIKES TABS AND DIGITAL MEDIA CAN PROVIDE EFFICIENT WAY TO LEARNING AND EDUCATION

OpenAIRE

Aditya Jain*, Aditya Sharma, Aditya Singh Baghel, Ambar Pathak

2016-01-01

The use of latest trends and technologies in academic research may now be changing with such a frequency in the universities in terms of faculties who teaches and students that learn. Each and every universities wants to not only improve the syllabus but they also want to upgrade their labs with latest use of hardware and software. They are also focusing upon the technological growth of the students and their students can also develop their applications in different zones like traffic managem...

21 CFR 310.4 - Biologics; products subject to license control.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Biologics; products subject to license control... to license control. (a) If a drug has an approved license under section 351 of the Public Health.... (b) To obtain marketing approval for radioactive biological products for human use, as defined in...

Optimizing Two-Dimensional Renewable Warranty Policies for Sensor Embedded Remanufactured Products

OpenAIRE

Alqahtani, Ammar; Gupta, Surendra M.

2017-01-01

Purpose: Remanufactured products, in addition to being environment friendly, are popular with consumers because they can offer the latest technology with lower prices in comparison to brand new products. However, some consumers are hesitant to buy remanufactured products because they are skeptical about the quality of the remanufactured product and thus are unsure of the extent to which the product will render services when compared to a new product. A strategy that remanufactu...

Latest experience on insertion devices at the National Synchrotron Light Source-II

International Nuclear Information System (INIS)

Tanabe, Toshiya; Cappadoro, Peter; Corwin, Todd

2016-01-01

National Synchrotron Light Source-II (NSLS-II) is the latest storage ring of 3 GeV energy with the horizontal emittance of the electron beam being 0.9 nm.rad. Nine In-Vacuum Undulators (IVUs) are utilized at the NSLS-II as of February 2016. All IVUs have a unique side window derived from the experience from the CHESS facility in Cornell University. An R and D activity called 'Vacuum Seal Test' was conducted to ensure the viability of aluminum wire seal. Another R and D activity to develop a measurement system for Cryogenic Permanent Magnet Undulator (CPMU) was also performed. Other in-air devices, namely damping wigglers (DWs) and elliptically polarizing undulators (EPUs) utilize extruded aluminum chambers with Non-Evaporable Getter (NEG) coating. The beam-based integral estimates were obtained from the virtual kicks at the upstream and downstream of the undulator that best fit the measured orbit distortion in a model lattice with Tracy. In some cases, there are fairly large discrepancies between magnetic measurement data and observed integrals by the beam. Beam studies were carried out to explain the discrepancies mentioned earlier. The latest experiences on ID development and commissioning are discussed in conjunction with related activities in the world. (author)

PLC based automatic control of pasteurize mix in ice cream production

Science.gov (United States)

Yao, Xudong; Liang, Kai

2013-03-01

This paper describes the automatic control device of pasteurized mix in the ice cream production process.We design a scheme of control system using FBD program language and develop the programmer in the STEP 7-Micro/WIN software, check for any bugs before downloading into PLC .These developed devices will able to provide flexibility and accuracy to control the step of pasteurized mix. The operator just Input the duration and temperature of pasteurized mix through control panel. All the steps will finish automatically without any intervention in a preprogrammed sequence stored in programmable logic controller (PLC). With the help of this equipment we not only can control the quality of ice cream for various conditions, but also can simplify the production process. This control system is inexpensive and can be widely used in ice cream production industry.

A Projection of Automated Book Production Control

Directory of Open Access Journals (Sweden)

Mario Barisic

2006-12-01

Full Text Available The paper elaborates on the recommendation of systematic introducing of XML technologies as a standard and integral factor in publishing and graphic business activities and as a further improvement of the existing PostScript graphic production platform. Procedures are proposed for applying norm setting in respect to production processes through related connections organized databases under XML technology in a hierarchical way, as well as a book production norm setting system. The proposal for work processes automation in the domain of printing business control is elaborated under the CIP4-JDF automating system. Operation results are used as guidelines for setting the elements of automated business operations in the book production domain, with integrated elements of new technologies, compatible with global trends.

An inventory control model for biomass dependent production systems

International Nuclear Information System (INIS)

Grado, S.C.; Strauss, C.H.

1993-01-01

The financial performance of a biomass dependent production system was critiqued based on the development and validation of an inventory control model. Dynamic programming was used to examine the constraints and capabilities of producing ethanol from various biomass crops. In particular, the model evaluated the plantation, harvest, and manufacturing components of a woody biomass supply system. The optimum wood to ethanol production scheme produced 38 million litres of ethanol in the harvest year, at 13.6 million litre increase over the least optimal policy as demonstrated in the dynamic programming results. The system produced ethanol at a delivered cost of $0.38 L -1 which was consistent with the unit costs from other studies. Nearly 60% of the delivered costs were in ethanol production. The remaining costs were attributed to growing biomass (14%), harvest and shipment of the crop (18%), storage of the raw material and finished product (7%) and open-quotes lost salesclose quotes (2%). Inventory control, in all phases of production, proved to be an important cost consideration throughout the model. The model also analyzed the employment of alternative harvesting policies and the use of different or multiple feedstocks. A comparison between the least cost wood system and an even cut wood system further revealed the benefits of using an inventory control system

Ozone Production and Control Strategies for Southern Taiwan

Science.gov (United States)

Shiu, C.; Liu, S.; Chang, C.; Chen, J.; Chou, C. C.; Lin, C.

2006-12-01

An observation-based modeling (OBM) approach is used to estimate the ozone production efficiency and production rate of O3 (P(O3)) in southern Taiwan. The approach can also provide an indirect estimate of the concentration of OH. Measured concentrations of two aromatic hydrocarbons, i.e. ethylbenzene/m,p-xylene, are used to estimate the degree of photochemical processing and the amounts of photochemically consumed NOx and NMHCs. In addition, a one-dimensional (1d) photochemical model is used to compare with the OBM results. The average ozone production efficiency during the field campaign in Kaohsiung-Pingtung area in Fall 2003 is found to be about 5, comparable to previous works. The relationship of P(O3) with NOx is examined in detail and compared to previous studies. The derived OH concentrations from this approach are in fair agreement with values calculated from the 1d photochemical model. The relationship of total oxidants (e.g. O3+NO2) versus initial NOx and NMHCs suggests that reducing NMHCs are more effective in controlling total oxidants than reducing NOx. For O3 control, reducing NMHC is even more effective than NOx due to the NO titration effect. This observation-based approach provides a good alternative for understanding the production of ozone and formulating ozone control strategy in urban and suburban environment without measurements of peroxy radicals.

Controlling nitrous oxide emissions from grassland livestock production systems

NARCIS (Netherlands)

Oenema, O.; Gebauer, G.; Rodriguez, M.; Sapek, A.; Jarvis, S.C.; Corré, W.J.; Yamulki, S.

1998-01-01

There is growing awareness that grassland livestock production systems are major sources of nitrous oxide (N2O). Controlling these emissions requires a thorough understanding of all sources and controlling factors at the farm level. This paper examines the various controlling factors and proposes

Applications of natural products in the control of mosquito ...

African Journals Online (AJOL)

Applications of natural products in the control of mosquito-transmitted ... African Journal of Biotechnology ... Ultimately, a paradigm shift in research that evaluates natural products in a comparative manner will help to produce new materials for ...

FPGA based Control of a Production Cell System

NARCIS (Netherlands)

Groothuis, M.A.; van Zuijlen, Jasper J.P.; Broenink, Johannes F.

Most motion control systems for mechatronic systems are implemented on digital computers. In this paper we present an FPGA based solution implemented on a low cost Xilinx Spartan III FPGA. A Production Cell setup with multiple parallel operating units is chosen as a test case. The embedded control

Technology and products of gas companies; Gas gaisha no Technology and Products

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-10

This paper presents the latest technology and products of gas companies. `Newly developed gas table for one-push automatic fish broiling` of Tokyo Gas Co. `Catalytic technology for decomposing dioxin generated by incinerator to make it harmless` of Osaka Gas Co. `Newly developed strong and kindly shower head` of Tokyo Gas Co. By laying fish on a sensor in a grill and appropriately setting upper and lower heating levers, user can skillfully broil fish only by pushing an ignition button. A temperature sensor attached to the center of a grill catches a change in surface temperature of fish, and automatically sets an appropriate broiling time according to the kind and volume of fish. A finish buzzer and automatic extinction mechanism are prepared. The technology decomposes dioxin in exhaust gas of incinerators to make it harmless. The catalyst is prepared by dispersing noble metal or oxide of several angstroms into activated carbon fibers. The shower head can switch hot water power by a control handle

Use of statistical process control in the production of blood components

DEFF Research Database (Denmark)

Magnussen, K; Quere, S; Winkel, P

2008-01-01

Introduction of statistical process control in the setting of a small blood centre was tested, both on the regular red blood cell production and specifically to test if a difference was seen in the quality of the platelets produced, when a change was made from a relatively large inexperienced...... by an experienced staff with four technologists. We applied statistical process control to examine if time series of quality control values were in statistical control. Leucocyte count in red blood cells was out of statistical control. Platelet concentration and volume of the platelets produced by the occasional...... occasional component manufacturing staff to an experienced regular manufacturing staff. Production of blood products is a semi-automated process in which the manual steps may be difficult to control. This study was performed in an ongoing effort to improve the control and optimize the quality of the blood...

NODC Standard Product: World ocean database 2005 (NCEI Accession 0099241)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The World Ocean Database 2005 (WOD05) DVD contains data, documentation, programs, and utilities for the latest release of this product. Data include 7.9 million...

[Modeling developmental aspects of sensorimotor control of speech production].

Science.gov (United States)

Kröger, B J; Birkholz, P; Neuschaefer-Rube, C

2007-05-01

Detailed knowledge of the neurophysiology of speech acquisition is important for understanding the developmental aspects of speech perception and production and for understanding developmental disorders of speech perception and production. A computer implemented neural model of sensorimotor control of speech production was developed. The model is capable of demonstrating the neural functions of different cortical areas during speech production in detail. (i) Two sensory and two motor maps or neural representations and the appertaining neural mappings or projections establish the sensorimotor feedback control system. These maps and mappings are already formed and trained during the prelinguistic phase of speech acquisition. (ii) The feedforward sensorimotor control system comprises the lexical map (representations of sounds, syllables, and words of the first language) and the mappings from lexical to sensory and to motor maps. The training of the appertaining mappings form the linguistic phase of speech acquisition. (iii) Three prelinguistic learning phases--i. e. silent mouthing, quasi stationary vocalic articulation, and realisation of articulatory protogestures--can be defined on the basis of our simulation studies using the computational neural model. These learning phases can be associated with temporal phases of prelinguistic speech acquisition obtained from natural data. The neural model illuminates the detailed function of specific cortical areas during speech production. In particular it can be shown that developmental disorders of speech production may result from a delayed or incorrect process within one of the prelinguistic learning phases defined by the neural model.

Latest status of manufacturing activity of ITER divertor and engineering issues on tungsten divertor

International Nuclear Information System (INIS)

Suzuki, Satoshi

2011-01-01

Divertors for ITER are now in construction. In the present chapter, the specification and the latest status of manufacturing of ITER divertors are presented. In addition, issues in the development of divertors for the fusion demo reactor are given on the basis of experiences on the ITER divertor development. (J.P.N.)

Universally applicable design concept of stably controlling an HTGR-hydrogen production system

International Nuclear Information System (INIS)

Hada, Kazuhiko; Shibata, Taiju; Nishihara, Tetsuo; Shiozawa, Shusaku

1996-01-01

An HTGR-hydrogen production system should be designed to have stable controllability because of a large difference in thermal dynamics between reactor and hydrogen production system and such a control design concept should be universally applicable to a variety of hydrogen production processes by the use of nuclear heat from HTGR. A transient response analysis of an HTGR-steam reforming hydrogen production system showed that a steam generator installed in a helium circuit for cooling the nuclear reactor provides stable controllability of the total system, resulting in avoiding a reactor scram. A survey of control design-related characteristics among several hydrogen production processes revealed the similarity of endothermic chemical reactions by the use of high temperature heat and that steam is required as a reactant of the endothermic reaction or for preheating a reactant. Based on these findings, a system design concept with stable controllability and universal applicability was proposed to install a steam generator as a downstream cooler of an endothermic reactor in the helium circuit of an HTGR-hydrogen production system. (author)

Drug-device combination products: regulatory landscape and market growth.

Science.gov (United States)

Bayarri, L

2015-08-01

Combination products are therapeutic and diagnostic products that combine drugs, devices and/or biological products, leading to safer and more effective treatments thanks to careful and precise drug targeting, local administration and individualized therapy. These technologies can especially benefit patients suffering from serious diseases and conditions such as cancer, heart disease, multiple sclerosis and diabetes, among others. On the other hand, drug-device combination products have also introduced a new dynamic in medical product development, regulatory approval and corporate interaction. Due to the increasing integration of drugs and devices observed in the latest generation of combination products, regulatory agencies have developed specific competences and regulations over the last decade. Manufacturers are required to fully understand the specific requirements in each country in order to ensure timely and accurate market access of new combination products, and the development of combination products involves a very specific pattern of interactions between manufacturers and regulatory agencies. The increased sophistication of the products brought to market over the last couple of decades has accentuated the need to develop drugs and devices collaboratively using resources from both industries, fostering the need of business partnering and technology licensing. This review will provide a global overview of the market trends, as well as (in the last section) an analysis of the drug-device combination products approved by the FDA during the latest 5 years. Copyright 2015 Prous Science, S.A.U. or its licensors. All rights reserved.

A comparison of push and pull production controls under machine breakdown

Directory of Open Access Journals (Sweden)

Prakash, J.

2011-01-01

Full Text Available Production control for high-mix production remains a complex issue. Common pull system replenishment generates large works-in-process (WIPs for each part type, especially under breakdown. This paper attempts to solve this by presenting a production control that classifies parts into two categories. The performances of three production control mechanisms under breakdown are compared. The production control mechanisms in consideration are push, shared constant WIP (CONWIP, and parallel CONWIP. A full-factorial simulation experiment was conducted. ANOVA was performed to determine the significant effects of input factors. Response surface methodology was used to demonstrate the behavior of performance measures in terms of these significant input factors. The results prove that parallel CONWIP is superior over shared CONWIP in terms of the average flow time per part. If categorical dispatch rules are employed, parallel CONWIP outperforms shared CONWIP in terms of service level. With high card count, parallel CONWIP generally produces lower bottleneck utilizations while maintaining a low average flow time per part than shared CONWIP.

The use of patient classification systems for production control of hospitals

NARCIS (Netherlands)

Vries, de G.G.; Vissers, J.M.H.; Vries, de G.

2000-01-01

Production control is an important issue for hospital management. Hospitals are faced with a growing demand for care and higher expectations for improved service delivery. For production control purposes information is required on different levels of aggregation: process resources and patient flows.

Earth and Space Science Electronic Theater: State-of-the-Art Visualization from the Latest Remote Sensing Observations. High Definition Television on the SMM IMAX Screen with Ultra High Performance Projector

Science.gov (United States)

Hasler, A. F.; Starr, David (Technical Monitor)

2001-01-01

Fritz Hasler (NASA/Goddard) will demonstrate the latest Blue Marble Digital Earth technology. We will fly in from space through Terra, Landsat 7, to 1 m Ikonos "Spy Satellite" data to Washington, NYC, Chicago, and LA. You will see animations using the new 1 km global datasets from the EOS Terra satellite. Spectacular new animations from Terra, Landsat 7, and SeaWiFS will be presented. See the latest animations of the super hurricanes like, Floyd, Luis, and Mitch, from GOES & TRMM. See movies assembled using new low cost HDTV nonlinear editing equipment that is revolutionizing the way we communicate scientific results. See climate change in action with Global Land & Ocean productivity changes over the last 20 years. Remote sensing observations of ocean SST, height, winds, color, and El Nino from GOES, AVHRR, SSMI & SeaWiFS are put in context with atmospheric and ocean simulations. Compare symmetrical equatorial eddies observed by GOES with the simulations.

A pilot scale demonstration of the DWPF process control and product verification strategy

International Nuclear Information System (INIS)

Hutson, N.D.; Jantzen, C.M.; Beam, D.C.

1992-01-01

The Defense Waste Processing Facility (DWPF) has been designed and constructed to immobilize Savannah River Site high level liquid waste within a durable borosilicate glass matrix for permanent storage. The DWPF will be operated to produce a glass product which must meet a number of product property constraints which are dependent upon the final product composition. During actual operations, the DWPF will control the properties of the glass product by the controlled blending of the waste streams with a glass-forming frit to produce the final melter feed slurry. The DWPF will verify control of the glass product through analysis of vitrified samples of slurry material. In order to demonstrate the DWPF process control and product verification strategy, a pilot-scale vitrification research facility was operated in three discrete batches using simulated DWPF waste streams. All of the DWPF process control methodologies were followed and the glass produce from each experiment was leached according to the Product Consistency Test. Results of the campaign are summarized

A pilot scale demonstration of the DWPF process control and product verification strategy

International Nuclear Information System (INIS)

Hutson, N.D.; Jantzen, C.M.; Beam, D.C.

1992-01-01

The Defense Waste Processing Facility (DWPF) has been designed and constructed to immobilize Savannah River Site high level liquid waste within a durable borosilicate glass matrix for permanent storage. The DWPF will be operated to produce a glass product which must meet a number of product property constraints which are dependent upon the final product composition. During actual operations, the DWPF will control the properties of the glass product by the controlled blending of the waste streams with a glass-forming frit to produce the final melter feed slurry. The DWPF will verify control of the glass product through analysis of vitrified samples of slurry material. In order to demonstrate the DWPF process control and product verification strategy, a pilot-scale vitrification research facility was operated in three discrete batches using simulated DWPF waste streams. All of the DWPF process control methodologies were followed and the glass product from each experiment was leached according to the Product Consistency Test. In this paper results of the campaign are summarized

From golden rice to drought-tolerant maize and new techniques to control plant disease - can we expect a breakthrough in crop production?

Directory of Open Access Journals (Sweden)

Tamas Komives

2017-02-01

Full Text Available This Minireview paper summarizes the views of the authors on the history and current status of golden rice – the highly promising concept of introducing new genes into existing rice strains to make them capable to accumulate beta carotene (the biochemical precursor of vitamin A in the grain. Based on the questionable success of genetically modified organisms to achieve a significant increase in food and feed production we speculate on the possibility of a breakthrough in this area via the latest discoveries in molecular biological techniques.

Zadig: latest improvements to Bremsstrahlung treatment and in-flight annihilation scheme; Zadig: amelioration du traitement Bremsstrahlung et traitement de l'annihilation en vol

Energy Technology Data Exchange (ETDEWEB)

Menard, St

2006-07-01

Multigroup cross-section for the 3-dimensional Monte-Carlo transport code DIANE are produced by the ZADIG code. Although DIANE does not transport the electrons and positrons, the production of Bremsstrahlung photons induced by the electrons and positrons during their slowing down is taken into account in the ZADIG code because the electron-gamma cascade is an important process in high energy gamma ray transport. ZADIG does not distinguish positrons from electrons except for the positron annihilation. However, the user can turn on this direction. This report presents the latest improvements to the Bremsstrahlung model of ZADIG and to the positron annihilation algorithm implemented in the code. Positrons can annihilate either in flight or at rest in the latest release of ZADIG. As MCNP does not take into account the annihilation in flight, results of ZADIG-DIANE calculations are compared to the results of GEANT-4 in order to validate the annihilation scheme of ZADIG. The results with annihilation divided by the results without present similar trends between 0.6 and 10 MeV for the 2 codes (GEANT-4 and ZADIG-DIANE), in other words an influence of 5%, so the annihilation scheme programmed in ZADIG appears to be satisfying and can be considered as validated.

Tensor Product Model Transformation Based Adaptive Integral-Sliding Mode Controller: Equivalent Control Method

Directory of Open Access Journals (Sweden)

Guoliang Zhao

2013-01-01

Full Text Available This paper proposes new methodologies for the design of adaptive integral-sliding mode control. A tensor product model transformation based adaptive integral-sliding mode control law with respect to uncertainties and perturbations is studied, while upper bounds on the perturbations and uncertainties are assumed to be unknown. The advantage of proposed controllers consists in having a dynamical adaptive control gain to establish a sliding mode right at the beginning of the process. Gain dynamics ensure a reasonable adaptive gain with respect to the uncertainties. Finally, efficacy of the proposed controller is verified by simulations on an uncertain nonlinear system model.

Associated top production (ttV, tV) in ATLAS and CMS

CERN Document Server

Sánchez Cruz, Sergio

2018-01-01

A set of measurements of top quark pair and single top quark production in association with standard model (SM) bosons performed by the CMS and ATLAS Collaborations is presented. The consistency of these results among themselves and with the SM prediction is discussed. The latest results on four top quark production are also shown.

Latest Advances in the Generation of Single Photons in Silicon Carbide

Directory of Open Access Journals (Sweden)

Albert Boretti

2016-06-01

Full Text Available The major barrier for optical quantum information technologies is the absence of reliable single photons sources providing non-classical light states on demand which can be easily and reliably integrated with standard processing protocols for quantum device fabrication. New methods of generation at room temperature of single photons are therefore needed. Heralded single photon sources are presently being sought based on different methods built on different materials. Silicon Carbide (SiC has the potentials to serve as the preferred material for quantum applications. Here, we review the latest advances in single photon generation at room temperatures based on SiC.

Use of statistical process control in the production of blood components

DEFF Research Database (Denmark)

Magnussen, K.; Quere, S.; Winkel, P.

2008-01-01

occasional component manufacturing staff to an experienced regular manufacturing staff. Production of blood products is a semi-automated process in which the manual steps may be difficult to control. This study was performed in an ongoing effort to improve the control and optimize the quality of the blood...

Dual substrate feedback control of specific growth-rate in vaccine production

NARCIS (Netherlands)

Neeleman, R.; Beuvery, E.C.; Vries, D.; Straten, van G.; Boxtel, van A.J.B.

2004-01-01

Abstract: Unexpectedly, primary concern of bio-pharmaceutical industry is not optimisation of product yield or cost reduction, but consistency in production and product quality. This paper describes the methodology and experimental results of specific growth-rate control for vaccine production. The

Radiation control of food and forest industry production in the Republic of Belarus

International Nuclear Information System (INIS)

Vasil'eva, I.P.; Barabashkin, A.V.; Kondrat'ev, A.G.

1993-01-01

Service of the Ministry of Health ( 151 radiology laboratories ) and The Ministry of Agriculture ( 1330 radiology laboratories ) carry out the permanent control of the content of radionuclides in food. Last years there was no case registered of drinking water with the content of radioactive substances exceeding the permissible level. Radiation control of food and agricultural raw products is carried out in several stages: at the place of production, during reprocessing and a control of ready made product. The fact that there was no case of delivery of the products with the content of radionuclides higher than permissible level for sale says about the reliability of the system of the control. The permissible levels of the content of radionuclides are presented for food, drinking water, products of forest industry and agricultural production. 1 tab

Pharmaceutical quality by design: product and process development, understanding, and control.

Science.gov (United States)

Yu, Lawrence X

2008-04-01

The purpose of this paper is to discuss the pharmaceutical Quality by Design (QbD) and describe how it can be used to ensure pharmaceutical quality. The QbD was described and some of its elements identified. Process parameters and quality attributes were identified for each unit operation during manufacture of solid oral dosage forms. The use of QbD was contrasted with the evaluation of product quality by testing alone. The QbD is a systemic approach to pharmaceutical development. It means designing and developing formulations and manufacturing processes to ensure predefined product quality. Some of the QbD elements include: Defining target product quality profile; Designing product and manufacturing processes; Identifying critical quality attributes, process parameters, and sources of variability; Controlling manufacturing processes to produce consistent quality over time. Using QbD, pharmaceutical quality is assured by understanding and controlling formulation and manufacturing variables. Product testing confirms the product quality. Implementation of QbD will enable transformation of the chemistry, manufacturing, and controls (CMC) review of abbreviated new drug applications (ANDAs) into a science-based pharmaceutical quality assessment.

Can Differentiated Production Planning and Control enable both Responsiveness and Efficiency in Food Production?

Directory of Open Access Journals (Sweden)

Anita Romsdal

2014-07-01

Full Text Available This paper addresses the complex production planning and control (PPC challenges in food supply chains. The study illustrates how food producers' traditional make‐to‐stock (MTS approach is not well suited to meet the trends of increasing product variety, higher demand uncertainty, increasing sales of fresh food products and more demanding customers. The paper proposes a framework for differentiated PPC that combines MTS with make‐to‐order (MTO.The framework matches products with the most appropriate PPC approaches and buffering techniques depending on market and product characteristics. The core idea is to achieve more volume flexibility in the production system by exploiting favourable product and market characteristics (high demand predictability, long customer order leadtime allowances and low product perishability. A case study is used to demonstrate how the framework can enable food producers to achieve efficiency in production, inventory and PPC processes – and simultaneously be responsive to market requirements.

Pelargonic acid for weed control in organic Vidalia sweet onion production

Science.gov (United States)

Cultivation using a tine weeder is a proven means to manage weeds in organic Vidalia® sweet onion production. If the initial cultivation is delayed, emerged weeds are not controlled by the tine weeder. In these cases, herbicides derived from natural products could be used to control the emerged we...

Numerical aspects of optimal control of penicillin production

Czech Academy of Sciences Publication Activity Database

Pčolka, M.; Čelikovský, Sergej

2014-01-01

Roč. 37, č. 1 (2014), s. 71-81 ISSN 1615-7591 R&D Projects: GA ČR(CZ) GA13-20433S Institutional support: RVO:67985556 Keywords : Optimal control * Nonlinear systems * Fermentation process * Gradient method optimization * Antibiotics production Subject RIV: BC - Control Systems Theory Impact factor: 1.997, year: 2014 http://library.utia.cas.cz/separaty/2014/TR/celikovsky-0424718.pdf

Review of nonchemical methods for controlling stored products pests

International Nuclear Information System (INIS)

Ignatowicz, S.

1996-01-01

Fumigation of stored products with methyl bromide has been an important means of limiting the loss of quality and quantity of these commodities that are subject to attack by cosmopolitan stored product pests. Methyl bromide was identified as a substance depleting ozone, and is expected to be withdrawn from production, importation, and use in Poland and other countries soon after 2000. Based on the current knowledge, most of alternatives to methyl bromide (controlled atmospheres, heat, cold, irradiation, biotechnical methods, inert dusts, biological methods, sanitation) have researchable gaps or other constraints. None of these alternatives used alone will replace methyl bromide. Successful pest control in the absence of methyl bromide will require the development of sophisticated pest monitoring and decision support systems to enable the use of integrated pest management strategies. (author)

First Clarkforkian equivalent Land Mammal Age in the latest Paleocene basal Sparnacian facies of Europe: fauna, flora, paleoenvironment and (bio)stratigraphy.

Science.gov (United States)

Smith, Thierry; Quesnel, Florence; De Plöeg, Gaël; De Franceschi, Dario; Métais, Grégoire; De Bast, Eric; Solé, Floréal; Folie, Annelise; Boura, Anaïs; Claude, Julien; Dupuis, Christian; Gagnaison, Cyril; Iakovleva, Alina; Martin, Jeremy; Maubert, François; Prieur, Judicaël; Roche, Emile; Storme, Jean-Yves; Thomas, Romain; Tong, Haiyan; Yans, Johan; Buffetaut, Eric

2014-01-01

The Paleocene-Eocene Thermal Maximum (PETM) is correlated with the first occurrences of earliest modern mammals in the Northern Hemisphere. The latest Paleocene Clarkforkian North American Land Mammal Age, that has yielded rodents and carnivorans, is the only exception to this rule. However, until now no pre-PETM localities have yielded modern mammals in Europe or Asia. We report the first Clarkforkian equivalent Land Mammal Age in the latest Paleocene deposits of the basal Sparnacian facies at Rivecourt, in the north-central part of the Paris Basin. The new terrestrial vertebrate and macroflora assemblages are analyzed through a multidisciplinary study including sedimentologic, stratigraphic, isotopic, and palynological aspects in order to reconstruct the paleoenvironment and to evaluate biochronologic and paleogeographic implications. The mammals are moderately diverse and not abundant, contrary to turtles and champsosaurs. The macroflora is exceptional in preservation and diversity with numerous angiosperms represented by flowers, fruits, seeds and wood preserved as lignite material, revealing an abundance of Arecaceae, Betulaceae, Icacinaceae, Menispermaceae, Vitaceae and probably Cornaceae. Results indicate a Late Paleocene age based on carbon isotope data, palynology and vertebrate occurrences such as the choristoderan Champsosaurus, the arctocyonid Arctocyon, and the plesiadapid Plesiadapis tricuspidens. However, several mammal species compare better with the earliest Eocene. Among these, the particular louisinid Teilhardimys musculus, also recorded from the latest Paleocene of the Spanish Pyrenees, suggests a younger age than the typical MP6 reference level. Nevertheless, the most important aspect of the Rivecourt fauna is the presence of dental remains of a rodent and a "miacid" carnivoran, attesting to the presence of two modern mammalian orders in the latest Paleocene of Europe. Interestingly, these two groups are also the only modern groups recorded

The Category of Personality in the Semantics of Latest English Borrowings in the Russian Idiomatics

Directory of Open Access Journals (Sweden)

Вадим Викторович Дементьев

2014-12-01

Full Text Available The article examines some of the latest Russian idioms by English origin. The semantics of these idioms has been seen on the material of the informal (including informal political discourse, in terms of opposition personality - impersonality, in connection with some of the new trends in public life.

Latest-Generation Transcatheter Aortic Valve Replacement Devices and Procedures.

Science.gov (United States)

Chamandi, Chekrallah; Puri, Rishi; Rodriguez-Gabella, Tania; Rodés-Cabau, Josep

2017-09-01

Transcatheter aortic valve replacement (TAVR) is a well-established treatment for patients with severe symptomatic aortic stenosis who are at high or prohibitive surgical risk. More recently, TAVR has emerged as a valid alternative to surgical aortic valve replacement for treating intermediate-risk patients, and several studies are currently evaluating the role of TAVR in low-risk patients. Transcatheter heart valve (THV) technologies have evolved considerably over time, and important iterations have been implemented in many of the latest-generation devices to (1) reduce the size and improve delivery system properties; (2) improve valve deployment, repositioning, and retrievability; and (3) reduce paravalvular leaks. This article reviews the main characteristics of, and clinical results associated with, the newer-generation THVs while providing an overview of novel TAVR indications. Copyright © 2017 Canadian Cardiovascular Society. Published by Elsevier Inc. All rights reserved.

Control in indoor radon decay products by air treatment devices

International Nuclear Information System (INIS)

Hinds, W.C.; Rudnick, S.N.; Maher, E.F.; First, M.W.

1983-01-01

An evaluation of the efficacy of household air cleaning devices as a means to control radon decay products in existing buildings is presented. Previous research on air cleaning methods for airborne radon decay products has been directed primarily to the control of radon decay products in mines and has only limited application to control in residences where dust concentration, air change rate, and humidity are lower than in mines. Results show that room size air cleaners can achieve substantial reductions in working levels in residences. Reductions observed at air infiltration rates of 0.52 air changes per hour ranged from 58 to 89%. Although the two air cleaners tested produced the greatest reductions, the low cost, simplicity, and other benefits of air circulating fans, particularly the ceiling fan, appear to make them most suitable for residences

Improved statistical method for temperature and salinity quality control

Science.gov (United States)

Gourrion, Jérôme; Szekely, Tanguy

2017-04-01

Climate research and Ocean monitoring benefit from the continuous development of global in-situ hydrographic networks in the last decades. Apart from the increasing volume of observations available on a large range of temporal and spatial scales, a critical aspect concerns the ability to constantly improve the quality of the datasets. In the context of the Coriolis Dataset for ReAnalysis (CORA) version 4.2, a new quality control method based on a local comparison to historical extreme values ever observed is developed, implemented and validated. Temperature, salinity and potential density validity intervals are directly estimated from minimum and maximum values from an historical reference dataset, rather than from traditional mean and standard deviation estimates. Such an approach avoids strong statistical assumptions on the data distributions such as unimodality, absence of skewness and spatially homogeneous kurtosis. As a new feature, it also allows addressing simultaneously the two main objectives of an automatic quality control strategy, i.e. maximizing the number of good detections while minimizing the number of false alarms. The reference dataset is presently built from the fusion of 1) all ARGO profiles up to late 2015, 2) 3 historical CTD datasets and 3) the Sea Mammals CTD profiles from the MEOP database. All datasets are extensively and manually quality controlled. In this communication, the latest method validation results are also presented. The method has already been implemented in the latest version of the delayed-time CMEMS in-situ dataset and will be deployed soon in the equivalent near-real time products.

Mannanase production by the lettuce endosperm : Control by the embryo.

Science.gov (United States)

Halmer, P; Bewley, J D

1979-01-01

Endo-β-mannanase (EC 3.2.1.78) is produced and secreted by the cells of the endosperm of lettuce (lactuca sativa L.) "seeds" (achenes). In imbibed intact seeds, production is prevented by inhibitors. If the endosperm is incubated alone, these inhibitors can be removed by leaching, allowing mannanase production. Abscisic acid, a component of lettuce seeds, inhibits the production of mannanase in the isolated endosperm, and may be involved in regulation of mannanase production in intact seeds. During germination the inhibition is removed, beginning 4-8 h after red-light irradiation, which was given 4 h from sowing. The cotyledons participate in this process, and are controlled by events occuring in the axis within 4 h from red-light irradiation. This control by the axis apparently depends on the exchange of diffusible substances. Both benzyladenine and gibberellic acid can replace the influence of the axis if the latter is removed, and may therefore be involved in the control by the axis of the rest of the seed.

Covariance upperbound controllers for networked control systems

International Nuclear Information System (INIS)

Ko, Sang Ho

2012-01-01

This paper deals with designing covariance upperbound controllers for a linear system that can be used in a networked control environment in which control laws are calculated in a remote controller and transmitted through a shared communication link to the plant. In order to compensate for possible packet losses during the transmission, two different techniques are often employed: the zero-input and the hold-input strategy. These use zero input and the latest control input, respectively, when a packet is lost. For each strategy, we synthesize a class of output covariance upperbound controllers for a given covariance upperbound and a packet loss probability. Existence conditions of the covariance upperbound controller are also provided for each strategy. Through numerical examples, performance of the two strategies is compared in terms of feasibility of implementing the controllers

The product composition control system at Savannah River: Statistical process control algorithm

International Nuclear Information System (INIS)

Brown, K.G.

1994-01-01

The Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS) will be used to immobilize the approximately 130 million liters of high-level nuclear waste currently stored at the site in 51 carbon steel tanks. Waste handling operations separate this waste into highly radioactive insoluble sludge and precipitate and less radioactive water soluble salts. In DWPF, precipitate (PHA) is blended with insoluble sludge and ground glass frit to produce melter feed slurry which is continuously fed to the DWPF melter. The melter produces a molten borosilicate glass which is poured into stainless steel canisters for cooling and, ultimately, shipment to and storage in an geologic repository. Described here is the Product Composition Control System (PCCS) process control algorithm. The PCCS is the amalgam of computer hardware and software intended to ensure that the melt will be processable and that the glass wasteform produced will be acceptable. Within PCCS, the Statistical Process Control (SPC) Algorithm is the means which guides control of the DWPF process. The SPC Algorithm is necessary to control the multivariate DWPF process in the face of uncertainties arising from the process, its feeds, sampling, modeling, and measurement systems. This article describes the functions performed by the SPC Algorithm, characterization of DWPF prior to making product, accounting for prediction uncertainty, accounting for measurement uncertainty, monitoring a SME batch, incorporating process information, and advantages of the algorithm. 9 refs., 6 figs

W/Z + jet Production at the LHC

CERN Document Server

Hesketh, G; The ATLAS collaboration

2012-01-01

This paper summarises the results on W and Z plus jet production at the CERN Large Hadron Collider, from both the ATLAS and CMS experiments. Based on the 2010 and 2011 datasets, measurements have been made of numerous cross sections provide excellent tests of the latest predictions from perturbative QCD calculations and event generators.

Trends in microbial control techniques for poultry products.

Science.gov (United States)

Silva, Filomena; Domingues, Fernanda C; Nerín, Cristina

2018-03-04

Fresh poultry meat and poultry products are highly perishable foods and high potential sources of human infection due to the presence of several foodborne pathogens. Focusing on the microbial control of poultry products, the food industry generally implements numerous preventive measures based on the Hazard Analysis and Critical Control Points (HACCP) food safety management system certification together with technological steps, such as refrigeration coupled to modified atmosphere packaging that are able to control identified potential microbial hazards during food processing. However, in recent years, to meet the demand of consumers for minimally processed, high-quality, and additive-free foods, technologies are emerging associated with nonthermal microbial inactivation, such as high hydrostatic pressure, irradiation, and natural alternatives, such as biopreservation or the incorporation of natural preservatives in packaging materials. These technologies are discussed throughout this article, emphasizing their pros and cons regarding the control of poultry microbiota and their effects on poultry sensory properties. The discussion for each of the preservation techniques mentioned will be provided with as much detail as the data and studies provided in the literature for poultry meat and products allow. These new approaches, on their own, have proved to be effective against a wide range of microorganisms in poultry meat. However, since some of these emergent technologies still do not have full consumer's acceptability and, taking into consideration the hurdle technology concept for poultry processing, it is suggested that they will be used as combined treatments or, more frequently, in combination with modified atmosphere packaging.

Latest Progress in Research on the SpaceLiner High-Speed Passenger Transportation Concept

OpenAIRE

Sippel, Martin; van Foreest, Arnold

2007-01-01

A vision aimed at revolutionizing ultra-long distance travel between different points on earth could be realized by a high-speed intercontinental passenger transport using rocket based, suborbital launchers. The paper gives an overview on the latest progress in conceptual design of the DLR SpaceLiner presenting geometrical size and mass data and describing results of trajectory simulations. The rockets are based on an advanced but technically conservative approach not relying on e...

Microbial control of hydrogen sulfide production

Energy Technology Data Exchange (ETDEWEB)

Montgomery, A.D.; Bhupathiraju, V.K.; Wofford, N.; McInerney, M.J. [Univ. of Oklahoma, Tulsa, OK (United States)] [and others

1995-12-31

A sulfide-resistant strain of Thiobacillus denitrificans, strain F, prevented the accumulation of sulfide by Desulfovibrio desulfuricans when both organisms were grown in liquid medium. The wild-type strain of T. denitrificans did not prevent the accumulation of sulfide produced by D. desulfuricans. Strain F also prevented the accumulation of sulfide by a mixed population of sulfate-reducing bacteria enriched from an oil field brine. Fermentation balances showed that strain F stoichiometrically oxidized the sulfide produced by D. desulfuricans and the oil field brine enrichment to sulfate. The ability of a strain F to control sulfide production in an experimental system of cores and formation water from the Redfield, Iowa, natural gas storage facility was also investigated. A stable, sulfide-producing biofilm was established in two separate core systems, one of which was inoculated with strain F while the other core system (control) was treated in an identical manner, but was not inoculated with strain F. When formation water with 10 mM acetate and 5 mM nitrate was injected into both core systems, the effluent sulfide concentrations in the control core system ranged from 200 to 460 {mu}M. In the test core system inoculated with strain F, the effluent sulfide concentrations were lower, ranging from 70 to 110 {mu}M. In order to determine whether strain F could control sulfide production under optimal conditions for sulfate-reducing bacteria, the electron donor was changed to lactate and inorganic nutrients (nitrogen and phosphate sources) were added to the formation water. When nutrient-supplemented formation water with 3.1 mM lactate and 10 mM nitrate was used, the effluent sulfide concentrations of the control core system initially increased to about 3,800 {mu}M, and then decreased to about 1,100 {mu}M after 5 weeks. However, in the test core system inoculated with strain F, the effluent sulfide concentrations were much lower, 160 to 330 {mu}M.

Application of the suggestion system in the improvement of the production process and product quality control

Science.gov (United States)

Gołaś, H.; Mazur, A.; Gruszka, J.; Szafer, P.

2016-08-01

The elaboration is a case study and the research was carried out in the company Alco-Mot Ltd., which employs 120 people. The company specializes in the production of lead poles for industrial and traction batteries using gravity casting. The elements embedded in the cast are manufactured on a machining centre, which provides the stability of the process and of the dimensions of the product as well as a very short production time. As a result of observation and analysis the authors have developed a concept for the implementation of a dynamic suggestion system in ALCO-MOT, including, among others, a standard for actions in the implementation of the suggestion system, as well as clear guidelines for the processing and presentation of the activities undertaken in the time between the establishment of the concept (suggestions) and the benefits analysis after the proposed solutions have been implemented. The authors also present how suggestions proposed by ALCO-MOT staff contributed to the improvement of the processes of production and quality control. Employees offered more than 30 suggestions, of which more than a half are being implemented now and further actions are being prepared for implementation. The authors will present the results of improvements in, for example, tool replacement time, scrap reduction. The authors will present how kaizen can improve the production and quality control processes. They will present how the production and quality control processes looked before and after the implementation of employee suggestions.

A Gentle Frost: Poet Helen Frost Talks about the Healing Power of Poetry and Her Latest Novel

Science.gov (United States)

Margolis, Rick

2006-01-01

This article presents an interview with poet Helen Frost. Frost talked about how poetry can help at-risk children. She also related the challenges she faced when she wrote her latest book titled "The Braid."

Dress like a Star: Retrieving Fashion Products from Videos

OpenAIRE

Garcia, Noa; Vogiatzis, George

2017-01-01

This work proposes a system for retrieving clothing and fashion products from video content. Although films and television are the perfect showcase for fashion brands to promote their products, spectators are not always aware of where to buy the latest trends they see on screen. Here, a framework for breaking the gap between fashion products shown on videos and users is presented. By relating clothing items and video frames in an indexed database and performing frame retrieval with temporal a...

Internal transport control in pot plant production

NARCIS (Netherlands)

Annevelink, E.

1999-01-01

Drawing up internal transport schedules in pot plant production is a very complex task. Scheduling internal transport at the operational level and providing control on a day-to-day or even hour-to-hour basis in particular requires a new approach. A hierarchical planning approach based on

Production control and supplier selection under demand disruptions

Directory of Open Access Journals (Sweden)

Xianzhe Chen

2010-12-01

Full Text Available This paper investigates the effects of demand disruptions on production control and supplier selection in a three-echelon supply chain system. The customer demand is modeled as a jump-diffusion process in a continuous-time setting. A two-number production-inventory policy is implemented in the production control model for the manufacturer. The objective is to minimize the long-term average total cost consisting of backlog cost, holding cost, switching cost, and ordering cost. The simulated annealing method is applied to search the optimal critical switching values. Furthermore, an improved analytical hierarchy process (AHP is proposed to select the best supplier, based on quantitative factors such as the optimal long-term total cost obtained through the simulated annealing method under demand disruptions and qualitative factors such as quality and service. Numerical studies are conducted to demonstrate the effects of demand disruptions in the face of various risk scenarios. Managerial insights from simulation results are provided as well. Our approaches can be implemented as the “stress test” for companies in front of various supply chain disruption scenarios.

Survey of licensee control room habitability practices

International Nuclear Information System (INIS)

Boland, J.F.; Brookshire, R.L.; Danielson, W.F.; Driscoll, J.W.; Graham, E.D.; McConnell, R.J.; Thompson, V.N.

1985-04-01

This document presents the results of a survey of Licensee control-room-habitability practices. The survey is part of a comprehensive program plan instituted in August 1983 by the NRC to respond to ongoing questions from the Advisory Committee on Reactor Safeguards (ACRS). The emphasis of this survey was to determine by field review the control-room habitability practices at three different plants, one of which is still under construction and scheduled to receive an operating license in 1986. The other two plants are currently operating, having received operating licenses in the mid-1970's and early 1980's. The major finding of this survey is that despite the fact that the latest control-room-habitability systems have become larger and more complex than earlier systems surveyed, the latest systems do not appear to be functionally superior. The major recommendation of this report is to consolidate into a single NRC document, based upon a comprehensive systems engineering approach, the pertinent criteria for control-room-habitability design

Application of controlled thermonuclear reactor fusion energy for food production

International Nuclear Information System (INIS)

Dang, V.D.; Steinberg, M.

1975-06-01

Food and energy shortages in many parts of the world in the past two years raise an immediate need for the evaluation of energy input in food production. The present paper investigates systematically (1) the energy requirement for food production, and (2) the provision of controlled thermonuclear fusion energy for major energy intensive sectors of food manufacturing. Among all the items of energy input to the ''food industry,'' fertilizers, water for irrigation, food processing industries, such as beet sugar refinery and dough making and single cell protein manufacturing, have been chosen for study in detail. A controlled thermonuclear power reactor was used to provide electrical and thermal energy for all these processes. Conceptual design of the application of controlled thermonuclear power, water and air for methanol and ammonia synthesis and single cell protein production is presented. Economic analysis shows that these processes can be competitive. (auth)

Advanced instrumentation and control techniques for nuclear power plants

International Nuclear Information System (INIS)

Hayakawa, Hiroyasu; Makino, Maomi

1989-01-01

Toshiba has been promoting the development and improvement of control and instrumentation (C and I) systems employing the latest technologies, to fulfill the requirements of nuclear power plants for increased reliability, the upgrading of functions, improved maintainability, and reasonable cost. Such development has been systematically performed based on a schematic view of integrated digital control and instrumentation systems, actively adopting state-of-the-art techniques such as the latest man-machine interfaces, digital and optical multiplexing techniques, and artificial intelligence. In addition, comprehensive feedback has been obtained from the accumulation of operating experience. This paper describes the purpose, contents and status of applications of representative newly-developed systems. (author)

Control of stored product pests by ionizing radiation

Energy Technology Data Exchange (ETDEWEB)

Hallman, Guy J [United States Department of Agriculture, Agricultural Research Service, Weslaco, TX (United States)

2013-01-15

Food irradiation for prevention of food-borne illness and disinfestation of commodities of pests is increasing in a number of countries. The goal of this review is to analyze the literature and current use of irradiation to control stored product pests and suggest research to optimize its potential. Doses to prevent reproduction of stored product pests range from 0.05 kGy for Tenebrio molitor L. to 0.45 kGy for Sitotroga cereallela (Olivier). Small but increasing amounts of grains and pulses are being irradiated in the world today especially in Asia. At least 33 countries permit irradiation of some stored products with 14 countries permitting it for all stored products. Ways in which stored product irradiation research and application may influence other uses of irradiation technology are also discussed. Deactivation of weed seeds might be an area of stored product phytosanitation where irradiation would have an advantage over other measures. (author)

Integration of production control and enterprise management systems in horticulture

NARCIS (Netherlands)

Verdouw, Cor; Robbemond, Robbert; Kruize, Jan Willem

2015-01-01

Production processes in horticulture are increasingly industrialized. Greenhouses have developed towards high-tech production plants that are highly automated by advanced systems for climate control, irrigation, crop monitoring, harvesting, internal transportation, sorting and packaging. At the

Virtual Factory Framework for Supporting Production Planning and Control.

Science.gov (United States)

Kibira, Deogratias; Shao, Guodong

2017-01-01

Developing optimal production plans for smart manufacturing systems is challenging because shop floor events change dynamically. A virtual factory incorporating engineering tools, simulation, and optimization generates and communicates performance data to guide wise decision making for different control levels. This paper describes such a platform specifically for production planning. We also discuss verification and validation of the constituent models. A case study of a machine shop is used to demonstrate data generation for production planning in a virtual factory.

Latest Magnet News

CERN Multimedia

Miele, P.

PRODUCTION OF TB COMPONENTS Production of the main components of the Barrel Toroid coils is well advanced in industry. They are being delivered to CERN and piled up in Building 180 ready for integration. Three coil casings have been completed at ALSTOM Power Switzerland and are standing in Building 180 waiting for integration (left photo). Ten double pancakes out of 16 have been completed at ANSALDO. Four of them have been delivered to CERN (right photo). Two vacuum vessels have been delivered to CERN by Felguera Construcciones Mecanicas, Spain. TB INTEGRATION Integrations of the TB components are performed at CERN in Building 180. Integration 1, which is the assembly of the two double pancakes into the coil casing (cold mass), has started. Preparation work is ongoing at the moment and the turning frame will be delivered to CERN mid-July 2002, ready for operation. Integration 2, which is the assembly of the cold mass and related components into the vacuum vessel, started with assembly of the cool...

On t-flavour production by neutrinos

International Nuclear Information System (INIS)

Phillips, R.J.N.

1979-06-01

Realistic upper bounds for t-quark production by neutrinos and antineutrinos are calculated in the standard six-quark model, including threshold suppression factors and the latest limits on mixing angles. For the presently allowed mass range msub(t) >- 14GeV, the production rates in existing neutrino beams are at best marginal, but increase very rapidly with energy. Detection of t-hadrons by semileptonic t-decay is considered; the resulting dimuon signal differs quantitatively from c and anti-c decay backgrounds, but its separation requires good statistics. (author)

STUDY OF PLANT-WIDE CONTROL IMPLEMENTATION IN PRODUCTION PROCESS OF GEOTHERMAL POWER PLANT

Directory of Open Access Journals (Sweden)

KATHERIN INDRIAWATI

2017-02-01

Full Text Available The design of plant-wide control system to optimize electricity production in geothermal power plant is proposed in this research. The objective is to overcome the deficiency due to changes in the characteristics of production well and fluctuation in electricity demand load. The proposed plant-wide control system has two main tasks; to maintain production process at optimum value and to increase efficiency. The pressure in separator and condenser is maintained at the respective set points under electrical load fluctuations in order to ensure optimum efficiency. The control system also reduce the usage of auxialiary electrical power and increase efficiency. The task was performed by controlling inlet cooling water temperatures to the condenser. It was concluded that the proposed control structure was able to increase efficiency and maintain production.

Latest news on Arabidopsis brassinosteroid perception and signaling

Directory of Open Access Journals (Sweden)

Klaus eHarter

2011-10-01

Full Text Available Brassinosteroids (BR are plant hormones regulating growth and development. In interaction with other hormones, they are involved in environmental cue responses. The standard BR response pathway model in Arabidopsis includes the perception of the hormone by the plasma membrane receptor BRASSINOSTEROID INSENSITIVE 1 (BRI1 and its hetero-oligomerisation with the co-receptor BRI1-ASSOCIATED RECEPTOR KINASE 1 (BAK1, followed by the activation of a signaling cascade finally resulting in the expression of BR-responsive genes. Recent findings have shed new light on the molecular mechanism of BR perception, which includes the hormone-induced formation of a platform in BRI1 extracellular domain for interaction with BAK1, and on very early events of signaling at the plasma membrane-cytoplasm interface. In addition, a fast BR response pathway that modifies the membrane potential and the expansion of the cell wall – both crucial processes preceding cell elongation growth – was identified. In this review, these latest findings are summarized and discussed against the background of the standard model of BRI1-dependent signaling.

[Latest trends and recommendations on epidemiology, diagnosis, and treatment of benign prostatic hyperplasia (BPH)].

Science.gov (United States)

Gabuev, A; Oelke, M

2011-05-01

A re-evaluation of established tests and treatments has become necessary after publication of several new guidelines on BPH during the past two years. This article describes the latest developments concerning epidemiology, diagnosis, and treatment of BPH. Diagnostic and treatment guidelines on BPH of the German, European, or North American urologists as well as UK doctors were reviewed according to key articles and latest modifications. The only German epidemiological trial on BPH demonstrated that all components of the BPH disease (symptoms - prostate enlargement - bladder outlet obstruction) increase with ageing. 27 % of German men will have disease progression within the next 5 years. Risk factors for disease progression are: age, symptoms, prostate size, PSA, urinary flow rate, and postvoiding residual urine. Diagnosis aims to distinguish BPH from other diseases with similar symptoms, quantify the BPH components, and estimate the individual risk of disease progression. BPH is an exclusion diagnosis. Ultrasonic measurement of detrusor wall thickness at the anterior wall of bladders filled with ≥ 250 mL can securely detect bladder outlet obstruction if the value is ≥ 2 mm. Watchful waiting and lifestyle modifications are suitable for men with mild symptoms and low disease progression risk. All drugs used in BPH treatment reduce symptoms but have no influence on bladder outlet obstruction. α-blockers are first-line drugs and may be combined with muscarinic receptor antagonists or 5α-reductase inhibitors to further increase efficacy. Prostate surgery is indicated when drug treatment is insufficient, the patient develops complications in the upper or lower urinary tract (absolute indications), or has severe bladder outlet obstruction. Standard operations are TURP in small (≤ 80 mL) or open prostatectomy in large prostates (> 80 mL). Minimally invasive, alter-native surgeries may be considered in selected men and -offer advantages with regard to the risk of

QUALITY CONTROL IN PRECAST PRODUCTION A case study on Tunnel Segment Manufacture

Directory of Open Access Journals (Sweden)

Yee Weng Cheong

2005-01-01

Full Text Available Quality control forms an integral part of precast production. An efficient quality system is most critical in the mass production of precast components in any project. In this study, the quality control system implemented in a precast factory is discussed. The precast factory is set up for the manufacture of large quantity of tunnel segments under a contract. Processes in the precast manufacture are discussed with respect to the control procedures in the quality inspection plan. The standard tests involved, roles of inspectors and corrective actions on-site are highlighted. Critical issues pertaining to the productivity and quality of precast production are reviewed. These include the quality of staff and maintenance, which could potentially affect the efficiency of the quality system. Some considerations should also be given to improve the workflow and productivity of the plant.

Latest development on the membrane formation for gas separation

Directory of Open Access Journals (Sweden)

Ahmad Fausi Ismail

2002-11-01

Full Text Available The first scientific observation related to gas separation was encountered by J.K Mitchell in 1831. However, the most remarkable and influential contribution to membrane gas separation technology was the systematic study by Thomas Graham in 1860. However only in 1979, membrane based gas separation technology was available and recognized as one of the most recent and advanced unit operations for gas separation processes. Membrane is fabricated by various methods and the parameters involved to a certain extent are very complicated. The phase inversion technique that is normally employed to produce membranes are dry/wet, wet, dry and thermal induced phase separation. Other techniques used to produce membrane are also reviewed. This paper reports the latest development in membrane formation for gas separation. The route to produce defect-free and ultrathin-skinned asymmetric membrane is also presented that represents the cutting edge technology in membrane gas separation process

Strategy for product composition control in the Hanford Waste Vitrification Plant

International Nuclear Information System (INIS)

Bryan, M.F.; Piepel, G.F.

1996-03-01

The Hanford Waste Vitrification Plant (HWVP) will immobilize transuranic and high-level radioactive waste in borosilicate glass. The major objective of the Process/Product Model Development (PPMD) cost account of the Pacific Northwest Laboratory HWVP Technology Development (PHTD) Project is the development of a system for guiding control of feed slurry composition (which affects glass properties) and for checking and documenting product quality. This document lays out the broad structure of HWVP's product composition control system, discusses five major algorithms and technical issues relevant to this system, and sketches the path of development and testing

CRITICAL CONTROL POINT IDENTIFICATION THROUGH TROPHOLOGICAL MEAT PRODUCTION CHAINFROM FIELD TO FORK

Directory of Open Access Journals (Sweden)

A. V. Borodin

2017-01-01

Full Text Available  Competitive production management is impossible without comprehensive hazard monitoring and critical parameters control at every stage of food production from raw material and auxiliary materials delivery to ready product realization, which is difficult without modern IT-support. The HACCP (Hazard Analysis and Critical Control Points approach to product safety differs from ready product testing for compliance with NaTD requirements (Normative and Technical Documentation and emphasizes the importance of the process approach to monitoring at every stage of food production. Critical control points (CCP identification is a stage, where the presence of a risk of manufacturing products that are unsafe for human health is recognized and it is possible to take action to its elimination, prevention or reduction to an acceptable level. The use of soſtware package significantly increases the enterprise HACCP system efficiency. The article describes methodological bases for IT-approach to the CCP identification in the trophological meat production chain from field to fork. The algorithmic support and soſtware for the «Decision tree», which allows detecting existing hazards, identifying risks, determining CCPs and describing them, has been developed.

Official control of plant protection products in Poland: detection of illegal products.

Science.gov (United States)

Miszczyk, Marek; Płonka, Marlena; Stobiecki, Tomasz; Kronenbach-Dylong, Dorota; Waleczek, Kazimierz; Weber, Roland

2018-04-03

Market presence of illegal and counterfeit pesticides is now a global problem. According to data published in 2012 by the European Crop Protection Association (ECPA), illegal products represent over 10% of the global market of plant protection products. Financial benefits are the main reason for the prevalence of this practice. Counterfeit and illegal pesticides may contain substances that may pose a threat to the environment, crops, animals, and humans, inconsistent with the label and registration dossier. In Poland, action against illegal and counterfeit plant protection products is undertaken by the Main Inspectorate of Plant Health and Seed Inspection (PIORiN), the police, the prosecution, and the pesticide producers. Results of chemical analyses carried out by the Institute of Plant Protection - National Research Institute Sośnicowice Branch, Pesticide Quality Testing Laboratory (PQTL IPP-NRI Sosnicowice Branch) indicate that a majority of illegal pesticides in Poland are detected in the group of herbicides. Products from parallel trade tend to have the most irregularities. This article describes the official quality control system of plant protection products in Poland and presents the analytical methods for testing pesticides suspected of adulteration and recent test results.

Non-destructive methods and means for quality control of structural products

International Nuclear Information System (INIS)

Dmitriev, V.V.

1989-01-01

Progressive non-destructive methods (acoustic, magnetic, radiation with liquid penetrants) and means of control of structural product quality, allowing to determine the state of products and structures not only immediately after their production but directly at the erected or reconstructed objects are described

The statutory approach: the control of chemical products

International Nuclear Information System (INIS)

Briens, F.

1997-01-01

The evaluation and management of risks linked with chemical products and in particular with petroleum products is now performed using all the available tools developed by the OECD or the European Union in order to harmonize the procedures between member states. This paper describes the statutory liabilities linked to the trade of chemical products of industrial use in the case of new and of existing chemical substances (classification, labelling, risk evaluation and reduction, physico-chemical properties, toxicological and eco-toxicological studies, neutralization, limitation of trade and use, import/export, protection of the ozone layer, etc..). It refers to the legal framework (orders, by-laws, decrees, guidelines..) defined by the OECD and the European Community and recalls the organization and administration of the competent authorities for the control of chemical products. (J.S.)

Are precues effective in proactively controlling taboo interference during speech production?

Science.gov (United States)

White, Katherine K; Abrams, Lise; Hsi, Lisa R; Watkins, Emily C

2018-02-07

This research investigated whether precues engage proactive control to reduce emotional interference during speech production. A picture-word interference task required participants to name target pictures accompanied by taboo, negative, or neutral distractors. Proactive control was manipulated by presenting precues that signalled the type of distractor that would appear on the next trial. Experiment 1 included one block of trials with precues and one without, whereas Experiment 2 mixed precued and uncued trials. Consistent with previous research, picture naming was slowed in both experiments when distractors were taboo or negative compared to neutral, with the greatest slowing effect when distractors were taboo. Evidence that precues engaged proactive control to reduce interference from taboo (but not negative) distractors was found in Experiment 1. In contrast, mixing precued trials in Experiment 2 resulted in no taboo cueing benefit. These results suggest that item-level proactive control can be engaged under certain conditions to reduce taboo interference during speech production, findings that help to refine a role for cognitive control of distraction during speech production.

Diversity and Control of Spoilage Fungi in Dairy Products: An Update

Science.gov (United States)

Valence, Florence; Mounier, Jérôme

2017-01-01

Fungi are common contaminants of dairy products, which provide a favorable niche for their growth. They are responsible for visible or non-visible defects, such as off-odor and -flavor, and lead to significant food waste and losses as well as important economic losses. Control of fungal spoilage is a major concern for industrials and scientists that are looking for efficient solutions to prevent and/or limit fungal spoilage in dairy products. Several traditional methods also called traditional hurdle technologies are implemented and combined to prevent and control such contaminations. Prevention methods include good manufacturing and hygiene practices, air filtration, and decontamination systems, while control methods include inactivation treatments, temperature control, and modified atmosphere packaging. However, despite technology advances in existing preservation methods, fungal spoilage is still an issue for dairy manufacturers and in recent years, new (bio) preservation technologies are being developed such as the use of bioprotective cultures. This review summarizes our current knowledge on the diversity of spoilage fungi in dairy products and the traditional and (potentially) new hurdle technologies to control their occurrence in dairy foods. PMID:28788096

Diversity and Control of Spoilage Fungi in Dairy Products: An Update

Directory of Open Access Journals (Sweden)

Lucille Garnier

2017-07-01

Full Text Available Fungi are common contaminants of dairy products, which provide a favorable niche for their growth. They are responsible for visible or non-visible defects, such as off-odor and -flavor, and lead to significant food waste and losses as well as important economic losses. Control of fungal spoilage is a major concern for industrials and scientists that are looking for efficient solutions to prevent and/or limit fungal spoilage in dairy products. Several traditional methods also called traditional hurdle technologies are implemented and combined to prevent and control such contaminations. Prevention methods include good manufacturing and hygiene practices, air filtration, and decontamination systems, while control methods include inactivation treatments, temperature control, and modified atmosphere packaging. However, despite technology advances in existing preservation methods, fungal spoilage is still an issue for dairy manufacturers and in recent years, new (bio preservation technologies are being developed such as the use of bioprotective cultures. This review summarizes our current knowledge on the diversity of spoilage fungi in dairy products and the traditional and (potentially new hurdle technologies to control their occurrence in dairy foods.

Recent ATLAS Results in Charmonium Production

CERN Document Server

Reznicek, Pavel; The ATLAS collaboration

2018-01-01

Production of heavy flavoured hadrons can serve as a probe of QCD processes and, in the case of production in heavy ion collisions, also as a probe of the properties of deconfined quark-gluon plasma. This paper describes the latest results in the production of charmonium at the ATLAS experiment at the Large Hadron Collider. The presented analyses include production of $J/\\psi$ and $\\psi$(2S) in $pp$ collisions and $\\sqrt{s} =$7, 8 and 13 TeV, and production of $J/\\psi$, $\\psi$(2S) and $\\Upsilon$(nS) in $pp$ and $p$+Pb collisions at $\\sqrt{s} =$5.02 TeV. In both the analyses prompt and non-prompt production is disentangled. In the latter analysis production suppression in $p$+Pb with respect to $pp$ collisions is measured and emphasis is put on the collision centrality dependence.

Inventory control in multi-item production systems

NARCIS (Netherlands)

Bruin, J.

2010-01-01

This thesis focusses on the analysis and construction of control policies in multiitem production systems. In such systems, multiple items can be made to stock, but they have to share the finite capacity of a single machine. This machine can only produce one unit at a time and if it is set-up for

Adejobi latest.pmd

African Journals Online (AJOL)

ACSS

2013-05-03

May 3, 2013 ... statistics and the logistic model. The results obtained ... addition to the reduction in the cost of production. (Diamini, 1976 ... development and growth may be studied either through the ... Considering a case of only one input flow in which a current ... firm's demand curve of an input shows the quantity which it ...

Assisting Children with Attention Deficit Hyperactivity Disorder Actively Reduces Limb Hyperactive Behavior with a Nintendo Wii Remote Controller through Controlling Environmental Stimulation

Science.gov (United States)

Shih, Ching-Hsiang; Yeh, Jui-Chi; Shih, Ching-Tien; Chang, Man-Ling

2011-01-01

The latest studies have adopted software technology which turns the Wii Remote Controller into a high-performance limb action detector, we assessed whether two persons with multiple disabilities would be able to control an environmental stimulus through limb action. This study extends the functionality of the Wii Remote Controller to the…

QUALITY CONTROL OF SOME TRADITIONAL MEAT PRODUCTS

Directory of Open Access Journals (Sweden)

S. DOBRINAS

2014-03-01

Full Text Available In this paper, we present the characterization of six traditional meat products: smoked file, smoked bacon, pork sausages, sausage prepared from swine’s entrails, pork pastrami, sheep sausages. Organoleptic tests (the aspect and shape, the aspect of freshly cut in the section, smell, taste and consistency, physico-chemical and microbiological determinations (NTG, Salmonella, Listeria monocytogenes and Escherichia coli were performed. These analyzes are a part of quality control that must be done in order to obtain a certificate from the Ministry of Agriculture for a traditional product. After identification of H2S and starch and according to fat oxidation degree it was concluded that analyzed samples didn’t contain counterfeiters and all parameters analyzed are within the maximum limits allowed by law. Considering all the procedures for manufacturing, characteristics of raw and auxiliary materials, organoleptic properties of final products analyzed in this study, it can be concluded that analyzed meat specialties meet the requirements of Ministry Order no. 690/28.09.2004 for the traditional products certification.

Evaluation of Manufacturing Process Performance by CONWIP Hybridization of Pull Controlled Production Systems

Directory of Open Access Journals (Sweden)

Srikanth O.

2018-01-01

Full Text Available The main objective of this paper is pioneering an innovative tactic for the synchronization of multi-stage, multi-line, production system. This tactic is mainly depends on the optimization policy, by means of distinct event simulation process for modeling, analysis and distinction of the execution of two alternatives of Kanban control mechanism namely SEKCS (Simultaneous Extended Kanban Control System and IEKCS (Independent Extended Kanban Control System. At this juncture the authors putting forward the two variants of Extended Kanban control system with the hybridization of CONWIP control policy to incite HSEKCS (Hybrid Simultaneous Extended Kanban Control System and HIEKCS (Hybrid Independent Extended Kanban Control System to make use of pooled benefits of a representative production situation in addition to improve the outcome. Therefore in this study the comparison in between different systems of proposed HEKCS specifically are HSEKCS and HIEKCS compared with the Extended Kanban Control Systems variants SEKCS and IEKCS. Simulation studies were conducted for all the five control policies considered and modeled on a multi-line, multi-stage assembly production control system. The relative performance parameters like Throughput or Production rate, Average Waiting Time and Average Work-in-Process, were assessed by means of exponentially varying demands.

Quantum Control of Molecular Processes

CERN Document Server

Shapiro, Moshe

2012-01-01

Written by two of the world's leading researchers in the field, this is a systematic introduction to the fundamental principles of coherent control, and to the underlying physics and chemistry.This fully updated second edition is enhanced by 80% and covers the latest techniques and applications, including nanostructures, attosecond processes, optical control of chirality, and weak and strong field quantum control. Developments and challenges in decoherence-sensitive condensed phase control as well as in bimolecular control are clearly described.Indispensable for atomic, molecular and chemical

Postharvest Practices for Organically Grown Products

Directory of Open Access Journals (Sweden)

Ilić Zoran S.

2018-03-01

Full Text Available Quality of produce cannot be improved after harvest, only maintained. Postharvest handling depends on the specific conditions of production, season, method of handling, and distance to market. Under organic production, growers harvest and market their produce at or near the peak ripeness more commonly than in many conventional systems. Organic production often includes more specialty varieties whose shelf life and shipping traits are reduced or even inherently poor. Harvesting and handling techniques that minimize injury to the commodity, as well as increased care with field and packinghouse sanitation, (chlorine, ozone, calcium hypochlorite, sodium hypochlorite and chlorine dioxide, acetic acid, peroxyacetic acid, vinegar, ethyl alcohol, hydrogen peroxide, etc. during postharvest processes are vital components of a postharvest management plan for organic products. Sodium carbonate, sodium bicarbonate, and physical treatments such as heat treatments (as hot water treatment or dips, short hot water rinsing and brushing or hot air can significantly lower the disease pressure on the harvested commodities. These sanitation practices are very easy to implement in the organic food production chain. They start in the field and continue during harvesting, sorting, packing, and transportation and continue even in the consumer’s home. All those treatments reduce rot development, provide quarantine security, and preserve fruit quality during cold storage and shelf life. In addition, the use chitosan, propolis, methyl jasmonate, essential oils, carnuba wax, biocontrol agents and modified atmosphere packaging can also reduce decay development during prolonged storage. All these treatments can be applied alone or in combination with each other in order to improve decay control after harvest and provide a healthy and safe product to the consumer. The aim of this chapter is to shed more light on the latest information on permitted treatments for organic

A fuel thermal conductivity correlation based on the latest experimental results

International Nuclear Information System (INIS)

Sontheimer, F.; Landskron, H.; Billaux, M.R.

2000-01-01

A new fuel thermal conductivity (ftc) correlation for UO 2 and (U,Gd)O 2 is presented, which is based on the relaxation-time theory of Klemens. The correlation is chosen because of its validity in a wide range of defect concentrations as for instance encountered in fuel with a wide range of burnup and gadolinia additions, as has been shown by Ishimoto. The phonon term of the new correlation has the form 1/x·arctan(x) , where x is a measure of the defect concentration introduced by burnup and gadolinia additions. For low defect concentrations, this term is identical with the classical form for the phonon term 1/(A+B.T). At high defect concentrations, however, when phonon-point defect scattering starts dominating over phonon-phonon scattering, the new correlation deviates from the classical formulation and has a distinctly weaker dependence on temperature and defect concentration than the classical form. The new arctan correlation in combination with an appropriate electronic ftc term is fitted to the Halden data base of fuel centre-line temperature measurements (represented by the ''Halden ftc correlation recommendation''). Agreement is very good up to a burnup of about 60 MWd/kgU; beyond, the arctan form has a saturating burnup degradation. The new arctan correlation in combination with an appropriate electronic ftc term is also shown to describe very well our latest ftc measurements on unirradiated gadolinia fuel up to 9% gadolinia content. Application to Halden measurements up to very high burnup is successful, when combined with the so-called ''rim-effect'', which counteracts the saturation tendency of the new correlation at high burnup. Latest laser thermal diffusivity measurements on irradiated gadolinia fuel in the frame of the NFIR program, although not yet open for literature and not discussed in the paper, indicate very good agreement with the new arctan correlation. (author)

Testing controlled productive knowledge of adverb-verb collocations ...

African Journals Online (AJOL)

A controlled productive test of adverb-verb collocations ..... The third approach to studying collocations, corpus analysis, ..... The collocation web model is thought to match Nation's (2001) psychological .... Theory, analysis, and applications. .... Canadian Modern ... Focus on vocabulary: Mastering the Academic Word List.

W/Z + jet Production at the LHC

CERN Document Server

INSPIRE-00054306

2012-01-01

This paper summarises results on W and Z plus jet production in pp collisions at $\\sqrt{s} = 7$ TeV at the CERN Large Hadron Collider, from both the ATLAS and CMS experiments. Based on the 2010 and 2011 datasets, measurements have been made of numerous cross sections providing excellent tests of the latest predictions from QCD calculations and event generators.

Conceptual Modelling for Product Configuration Systems

DEFF Research Database (Denmark)

Shafiee, Sara

Individual customization of goods and processes in different industries leads to complexity due to a growing mix of products both regarding characteristics of products and support services. In order to eliminate complexity and challenges in product/process customizing, smart IT systems called...... Product Configuration Systems (PCS), have been proposed as the solution both by researchers and practitioners and various benefits are mentioned from utilizing PCSs. Based on the latest literature, there are challenges reported in all phases of PCS projects including planning, development......, and documentation. Moreover, the challenges become more serious when it involves complicated products/processes in engineer-to-order (ETO) companies. The purpose of this thesis is to contribute to the existing knowledge of managing PCS projects by proposing frameworks and tools to address some of the main...

Optimal Control Approaches to the Aggregate Production Planning Problem

Directory of Open Access Journals (Sweden)

Yasser A. Davizón

2015-12-01

Full Text Available In the area of production planning and control, the aggregate production planning (APP problem represents a great challenge for decision makers in production-inventory systems. Tradeoff between inventory-capacity is known as the APP problem. To address it, static and dynamic models have been proposed, which in general have several shortcomings. It is the premise of this paper that the main drawback of these proposals is, that they do not take into account the dynamic nature of the APP. For this reason, we propose the use of an Optimal Control (OC formulation via the approach of energy-based and Hamiltonian-present value. The main contribution of this paper is the mathematical model which integrates a second order dynamical system coupled with a first order system, incorporating production rate, inventory level, and capacity as well with the associated cost by work force in the same formulation. Also, a novel result in relation with the Hamiltonian-present value in the OC formulation is that it reduces the inventory level compared with the pure energy based approach for APP. A set of simulations are provided which verifies the theoretical contribution of this work.

Features of the latest version of the PHITS code

International Nuclear Information System (INIS)

Sato, Tatsuhiko; Matsuda, Norihiro; Hashimoto, Shintaro; Iwamoto, Yosuke; Noda, Shusaku; Ogawa, Tatsuhiko; Nakajima, Hiroshi; Fukahori, Tokio; Okumura, Keisuke; Kai, Tetsuya; Chiba, Satoshi; Niita, Koji; Iwase, Hiroshi; Furuta, Takuya

2013-01-01

A Multi-purpose Monte Carlo Particle and Heavy Ion Transport code System, PHITS, developed through collaborations between JAEA and several institutes in Japan and Europe, and upgraded recently and released as PHITS2.52 is presented as an overview. In the new version, higher accuracy of the simulation was achieved by implementing the latest nuclear reaction models such as Liege intra-nuclear cascade version 4.6 (INCL4.6) and a statistical multi-fragmentation model including JAM and JQMD for high-energy regions. The reliability of the simulation code was improved by modifying both the algorithms for the electron-, positron-, and photon-transport simulations in terms of not only the code itself but also the contents of its package, such as the attached data libraries. More than 800 researchers have been registered as PHITS users, and they apply the code to various research and development fields such as nuclear technology, accelerator design, medical physics, and cosmic-ray research. (S. Ohno)

The vehicle routing problem latest advances and new challenges

CERN Document Server

Golden, Bruce L; Wasil, Edward A

2008-01-01

The Vehicle Routing Problem (VRP) has been an especially active and fertile area of research. Over the past five to seven years, there have been numerous technological advances and exciting challenges that are of considerable interest to students, teachers, and researchers. The Vehicle Routing Problem: Latest Advances and New Challenges will focus on a host of significant technical advances that have evolved over the past few years for modeling and solving vehicle routing problems and variants. New approaches for solving VRPs have been developed from important methodological advances. These developments have resulted in faster solution algorithms, more accurate techniques, and an improvement in the ability to solve large-scale, complex problems. The book will systematically examine these recent developments in the VRP and provide the following in a unified and carefully developed presentation: Present novel problems that have arisen in the vehicle routing domain and highlight new challenges for the field; Pre...

Targeting Nanomedicine to Brain Tumors: Latest Progress and Achievements.

Science.gov (United States)

Van't Root, Moniek; Lowik, Clemens; Mezzanotte, Laura

2017-01-01

Targeting nanomedicine to brain tumors is hampered by the heterogeneity of brain tumors and the blood brain barrier. These represent the main reasons of unsuccessful treatments. Nanomedicine based approaches hold promise for improved brain tissue distribution of drugs and delivery of combination therapies. In this review, we describe the recent advancements and latest achievements in the use of nanocarriers, virus and cell-derived nanoparticles for targeted therapy of brain tumors. We provide successful examples of nanomedicine based approaches for direct targeting of receptors expressed in brain tumor cells or modulation of pathways involved in cell survival as well as approaches for indirect targeting of cells in the tumor stroma and immunotherapies. Although the field is at its infancy, clinical trials involving nanomedicine based approaches for brain tumors are ongoing and many others will start in the near future. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Statistical assessment and hydrological utility of the latest multi-satellite precipitation analysis IMERG in Ganjiang River basin

Science.gov (United States)

Li, Na; Tang, Guoqiang; Zhao, Ping; Hong, Yang; Gou, Yabin; Yang, Kai

2017-01-01

This study aims to statistically and hydrologically assess the hydrological utility of the latest Integrated Multi-satellitE Retrievals from Global Precipitation Measurement (IMERG) multi-satellite constellation over the mid-latitude Ganjiang River basin in China. The investigations are conducted at hourly and 0.1° resolutions throughout the rainy season from March 12 to September 30, 2014. Two high-quality quantitative precipitation estimation (QPE) datasets, i.e., a gauge-corrected radar mosaic QPE product (RQPE) and a highly dense network of 1200 rain gauges, are used as the reference. For the implementation of the study, first, we compare IMERG product and RQPE with rain gauge-interpolated data, respectively. The results indicate that both remote sensing products can estimate precipitation fairly well over the basin, while RQPE significantly outperforms IMERG product in almost all the studied cases. The correlation coefficients of RQPE (CC = 0.98 and CC = 0.67) are much higher than those of IMERG product (CC = 0.80 and CC = 0.33) at basin and grid scales, respectively. Then, the hydrological assessment is conducted with the Coupled Routing and Excess Storage (CREST) model under multiple parameterization scenarios, in which the model is calibrated using the rain gauge-interpolated data, RQPE, and IMERG products respectively. During the calibration period (from March 12 to May 31), the simulated streamflow based on rain gauge-interpolated data shows the highest Nash-Sutcliffe coefficient efficiency (NSCE) value (0.92), closely followed by the RQPE (NSCE = 0.84), while IMERG product performs barely acceptable (NSCE = 0.56). During the validation period (from June 1 to September 30), the three rainfall datasets are used to force the CREST model based on all the three calibrated parameter sets (i.e., nine combinations in total). RQPE outperforms rain gauge-interpolated data and IMERG product in all validation scenarios, possibly due to its advantageous capability

Smart Product Design and Production Control for Effective Mass Customization in the Industry 4.0 Concept

Directory of Open Access Journals (Sweden)

Zawadzki Przemysław

2016-09-01

Full Text Available The paper presents a general concept of smart design and production control as key elements for efficient operation of a smart factory. The authors present various techniques that aid the design process of individualized products and organization of their production in the context of realization of the mass customization strategy, which allows a shortened time of development for a new product. Particular attention was paid to integration of additive manufacturing technologies and virtual reality techniques, which are a base of the so-called hybrid prototyping.

Managing unforeseen events in production scheduling and control

DEFF Research Database (Denmark)

Arica, E.; Falster, Peter; Hvolby, H. H.

2016-01-01

initial plans unfeasible or obsolete during production execution. How to effectively handle the unscheduled events and take corrective actions still remains a central question to academics and practitioners. In this paper, we explore this issue through a review of the relevant literature and an in......The production planning and control process is performed within complex and dynamic organizations made up of customer expectations, equipment, materials, people, information, and technologies. Changes in both internal and external factors can create a variety of unforeseen events, which make...

Improving production control within the automotive industry

Energy Technology Data Exchange (ETDEWEB)

Simon, R L

1982-01-01

The problems of controlling and minimising design and manufacturing information within the automotive industry are both costly and do not make maximum use of previous experience. With the advent of CAD/CAM, many new techniques have evolved for the speedy construction of design and manufacturing data bases. A means of binding together these data bases and controlling the design and process planning information is now presented in the form of Computervision's Migraphics and Miplan software. This gives a data retrieval capability from all area's of the production cycle including design and detail, numerical control and robotics, process planning, manufacture and procurement. Together with its numerous analytical capabilities this sorftware provides an excellent tool for the optimisation of manufacturing techniques, thus providing a complete CAD/CAM system from a single data base.

Consumer Health: Does Advertising Work on You? and Evaluating a Product's Health Claims.

Science.gov (United States)

Cox, Carolyn C.

This paper describes lessons for teaching middle and high school students how to determine if they are influenced by the power of advertising and how to evaluate a product's health claims. To determine the influence of advertising, teachers have high school students discuss what their latest health product/service purchase was, why they bought it,…

Peru seeking buyer for productive offshore tract

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that Petroleos del Peru (Petroperu) is seeking a buyer for its Petromar offshore exploration and production unit. Peru's national oil company wants to sell Petromar acreage, production, and production installations on Block Z-2b for $200 million, payable at $10 million/year for 20 years, plus a share of future production. Petroperu is offering a full interest petroleum exploration and exploitation contract for 30 years for oil and as long as 40 years in the case of gas exploitation. The company seeking the smallest share of current and incremental future production to operate Block Z-2b will be awarded the acreage. Petromar's sale is the latest announced under Peru's privatization program ordered by President Alberto Jujimori

The latest progress of TILLING technique and its prospects in irradiation mutation breeding

International Nuclear Information System (INIS)

Du Yan; Yu Lixia; Liu Qingfang; Zhou Libin; Li Wenjian

2011-01-01

TILLING (Targeting Induced Local Lesions IN Genomes) is a novel, high-throughput and low-cost reverse genetics technique. In recent years, with innovation of the mutation screening techniques, TILLING platform has become more diversified, which makes the operation of TILLING technique more simple and rapid. For this reason, it is widely used in crop breeding research. In this paper, we summarized the latest progress of TILLING technique, meanwhile, we also discussed the prospect of combining irradiation mutation with the high-throughput TILLING technique in mutation breeding. (authors)

A lean production control system for high-variety/low-volume environments : a case study implementation

NARCIS (Netherlands)

Slomp, J.; Bokhorst, J.A.C.; Germs, R.

2009-01-01

Due to the success of lean manufacturing, many companies are interested in implementing a lean production control system. Lean production control principles include the levelling of production, the use of pull mechanisms and takt time control. These principles have mainly been applied in high volume

Repeat transcatheter aortic valve implantation using a latest generation balloon-expandable device for treatment of failing transcatheter heart valves.

Science.gov (United States)

Schaefer, Andreas; Treede, Hendrik; Seiffert, Moritz; Deuschl, Florian; Schofer, Niklas; Schneeberger, Yvonne; Blankenberg, Stefan; Reichenspurner, Hermann; Schaefer, Ulrich; Conradi, Lenard

2016-01-15

Paravalvular leakage (PVL) is a known complication of transcatheter aortic valve implantation (TAVI) and is associated with poor outcome. Besides balloon-post-dilatation, valve-in-valve (ViV) procedures can be taken into consideration to control this complication. Herein we present initial experience with use of the latest generation balloon-expandable Edwards Sapien 3® (S3) transcatheter heart valve (THV) for treatment of failing THVs. Between 01/2014 and 12/2014 three patients (two male, age: 71-80 y, log EUROScore I: 11.89 - 32.63) with failing THVs were refered to our institution for further treatment. THV approach with secondary implantation of an S3 was chosen after mutual agreement of the local interdisciplinary heart team at an interval of 533-1119 days from the index procedure. The performed procedures consisted of: S3 in Sapien XT, JenaValve and CoreValve. Successful transfemoral implantation with significant reduction of PVL was achieved in all cases. No intraprocedural complications occurred regarding placement of the S3 with a postprocedural effective orifice area (EOA) of 1.5-2.5 cm(2) and pressure gradients of max/mean 14/6-36/16 mmHg. 30-day mortality was 0%. At the latest follow-up of 90-530 days, all patients are alive and well with satisfactory THV function. Regarding VARC-2 criteria one major bleeding and one TIA was reported. In the instance of moderate or severe aortic regurgitation after TAVI, S3 ViV deployment is an excellent option to reduce residual regurgitation to none or mild. For further assertions concerning functional outcomes long-term results have to be awaited.

Plant response-based sensing for control starategies in sustainable greenhouse production

International Nuclear Information System (INIS)

Kacira, M.; Sase, S.; Okushima, L.; Ling, P.P.

2005-01-01

The effect of environmental variability is one of the major concerns in experimental design for both research in plant systems and greenhouse plant production. Microclimates surrounding plants are not usually uniform. Therefore, many samples and sensors are required to obtain a true representation of the plant population. A plant monitoring system capable of reducing the required number of samples by reducing environmental variability would be more advantageous. To better understand plant-environment interaction, it is essential to study plants, microclimate surrounding the plants and the growth media. To achieve this, the monitoring system must be equipped with proper instrumentation. To achieve proper management practices and sustainable greenhouse production, it is essential first to understand plants and their interactions with their surroundings and then establish plant response-based sensing and control strategies for greenhouse processes. Therefore, an effort was conducted to review and discuss current sensing and control strategies in greenhouse research and plant production and provide recommendations on plant response-based sensing and control strategies for sustainable greenhouse production

Different approaches to overcome uncertainties of production systems

Science.gov (United States)

Azizi, Amir; Sorooshian, Shahryar

2015-05-01

This study presented a comprehensive review on the understanding of uncertainty and the current approaches that have been proposed to handle the uncertainties in the production systems. This paper classified proposed approaches into 11 groups. The paper studied 114 scholarly papers through various international journals. The paper added the latest findings to the body of knowledge to the current reservoir of understanding of the production uncertainties. Thus, the paper prepared the needs of researchers and practitioners for easy references in this area. This review also provided an excellent source to continue further studies on how to deal with the uncertainties of production system.

Ionizing radiation for insect control in grain and grain products

International Nuclear Information System (INIS)

Tilton, E.W.; Brower, J.H.

1987-01-01

A technical review summarizes and discusses information on various aspects of the use of ionizing radiation for the control of insect infestation in grains and grain products. Topics include: the effects of ionizing radiation on insects infesting stored-grain products; the 2 main types of irradiators (electron accelerators; radioisotopes (e.g.: Co-60; Cs-137); dosimetry systems and methodology; variations in radiation resistance by stored-product pests; the proper selection of radiation dose; the effects of combining various treatments (temperature, infrared/microwave radiation, hypoxia, chemicals) with ionizing radiation; sublethal radiation for controlling bulk grain insects; the feeding capacity of irradiated insects; the susceptibility of insecticide-resistant insects to ionizing radiation; and the possible resistance of insects to ionizing radiation. Practical aspects of removing insects from irradiated grain also are discussed

Agro. no 1 June Latest

African Journals Online (AJOL)

1Department of Crop Production, Soil and Environmental Management, Bowen University,. P.M.B 284, Iwo ... (90kgNha ) resulted in the production of seedling that was superior in dry matter yield to any other ..... Handbook of Energy Crops.

Real-time product attribute control to manufacture antibodies with defined N-linked glycan levels.

Science.gov (United States)

Zupke, Craig; Brady, Lowell J; Slade, Peter G; Clark, Philip; Caspary, R Guy; Livingston, Brittney; Taylor, Lisa; Bigham, Kyle; Morris, Arvia E; Bailey, Robert W

2015-01-01

Pressures for cost-effective new therapies and an increased emphasis on emerging markets require technological advancements and a flexible future manufacturing network for the production of biologic medicines. The safety and efficacy of a product is crucial, and consistent product quality is an essential feature of any therapeutic manufacturing process. The active control of product quality in a typical biologic process is challenging because of measurement lags and nonlinearities present in the system. The current study uses nonlinear model predictive control to maintain a critical product quality attribute at a predetermined value during pilot scale manufacturing operations. This approach to product quality control ensures a more consistent product for patients, enables greater manufacturing efficiency, and eliminates the need for extensive process characterization by providing direct measures of critical product quality attributes for real time release of drug product. © 2015 American Institute of Chemical Engineers.

Lean Production Control at a High-Variety, Low-Volume Parts Manufacturer

NARCIS (Netherlands)

Bokhorst, Jos A. C.; Slomp, Jannes

2010-01-01

Eaton Electric General Supplies, a parts manufacturing unit that supplies parts for Eaton's electrical business unit, implemented several lean control elements in its high-variety, low-volume production units. These control elements include a constant work-in-process mechanism to limit and control

78 FR 55099 - Established Aggregate Production Quotas for Schedule I and II Controlled Substances and...

Science.gov (United States)

2013-09-09

... aggregate production quotas, an additional 25% of the estimated medical, scientific, and research needs as... Production Quotas for Schedule I and II Controlled Substances and Established Assessment of Annual Needs for... initial 2014 aggregate production quotas for controlled substances in Schedules I and II of the Controlled...

The power of design product innovation in sustainable energy technologies

CERN Document Server

Reinders, Angele H; Brezet, Han

2012-01-01

The Power of Design offers an introduction and a practical guide to product innovation, integrating the key topics that are necessary for the design of sustainable and energy-efficient products using sustainable energy technologies. Product innovation in sustainable energy technologies is an interdisciplinary field. In response to its growing importance and the need for an integrated view on the development of solutions, this text addresses the functional principles of various energy technologies next to the latest design processes and innovation methods. From the perspec

The Latest IceCube Results and the Implications

Science.gov (United States)

Mase, Keiichi

IceCube was built at the South Pole and aims to detect high energy neutrinos from the universe mainly above 100 GeV. The transparent ice media allows us to build a 1 km3 large detection volume to detect the rarely interacting particles. Neutrinos are thought to be generated at astrophysical sources such as active galactic nuclei and gamma-ray bursts. Nature of the rare interaction with matters and little deflection by a magnetic field makes it possible to explore such sources located at the deep universe. Since the neutrinos are produced through collisions of hadronic particles, the observation can elucidate the origin of cosmic rays, which is still mystery after the discovery 100 years ago. The detector was completed at the end of 2010 and is running smoothly. Recently, IceCube has found the first evidence of extraterrestrial neutrinos with energies above approximately 60 TeV. IceCube also contributes to elementary particle physics by searching for neutrinos produced in self-annihilation of SUSY particles such as neutralinos and by investigating atmospheric neutrino oscillations. The latest IceCube results and the corresponding implications are presented.

User based preference indoor climate control

OpenAIRE

Zeiler, W.; Boxem, G.; Houten, van, M.A.; Wortel, W.; Velden, van der, J.A.J.; Kamphuis, I.G.; Hommelberg, M.P.F.; Tanabe, S.-I.; Kato, S.

2007-01-01

In comfort control strategy there is an exciting development based on inclusive design: the user’s preferences and their behaviour have become central in the building services control strategy. Synergy between end-user and building is the ultimate in the intelligent comfort control concept. This new comfort control technology is based on the use of the latest development in agent technology and can further reduce energy consumption of buildings while at the same time improve individual comfor...

Laparoscopic colorectal surgery: Current status and implementation of the latest technological innovations.

Science.gov (United States)

Pascual, Marta; Salvans, Silvia; Pera, Miguel

2016-01-14

The introduction of laparoscopy is an example of surgical innovation with a rapid implementation in many areas of surgery. A large number of controlled studies and meta-analyses have shown that laparoscopic colorectal surgery is associated with the same benefits than other minimally invasive procedures, including lesser pain, earlier recovery of bowel transit and shorter hospital stay. On the other hand, despite initial concerns about oncological safety, well-designed prospective randomized multicentre trials have demonstrated that oncological outcomes of laparoscopy and open surgery are similar. Although the use of laparoscopy in colorectal surgery has increased in recent years, the percentages of patients treated with surgery using minimally invasive techniques are still reduced and there are also substantial differences among centres. It has been argued that the limiting factor for the use of laparoscopic procedures is the number of surgeons with adequate skills to perform a laparoscopic colectomy rather than the tumour of patients' characteristics. In this regard, future efforts to increase the use of laparoscopic techniques in colorectal surgery will necessarily require more efforts in teaching surgeons. We here present a review of recent controversies of the use of laparoscopy in colorectal surgery, such as in rectal cancer operations, the possibility of reproducing complete mesocolon excision, and the benefits of intra-corporeal anastomosis after right hemicolectomy. We also describe the results of latest innovations such as single incision laparoscopic surgery, robotic surgery and natural orifice transluminal endoscopic surgery for colon and rectal diseases.

EFFECT OF CONVENTIONAL AND ALTERNATIVE PRODUCTS ON POSTHARVEST DISEASE CONTROL IN AVOCADOS

Directory of Open Access Journals (Sweden)

Ivan Herman Fischer

2018-02-01

Full Text Available ABSTRACT Postharvest diseases constitute a serious problem for avocado commercialization. Thus, the present study aimed to evaluate the effect of conventional and alternative products in controlling diseases affecting ‘Hass’ avocados in the field and in the postharvest by carrying out physicochemical characterization of fruits subjected to postharvest treatments. In the field, besides the management adopted by the farmer, seven products were sprayed three times during fruiting for evaluation. Postharvest products were diluted in water or in oxidized polyethylene wax and shellac. Water treatments with potassium phosphite, Soil-Set®, chlorine dioxide, thyme essential oil, sodium bicarbonate, lemon grass essential oil and thiabendazole reduced the incidence of diseased fruits, and anthracnose, the main disease, was controlled with sodium bicarbonate, lemon grass essential oil and thiabendazole. Greater soluble solids content was found for control (water, chlorine dioxide, acibenzolar-S-methyl and thiabendazole. For the products that reduced anthracnose, there was no correlation between the disease and the physicochemical parameters, evidencing that the disease control is not associated with delayed ripening. For wax treatments, diseases were not controlled, and the fruits presented lower titratable acidity with thyme essential oil, sodium bicarbonate, control (wax, acibenzolar-S-methyl and lemon grass essential oil. Control and thyme essential oil were highlighted for maintaining the green coloration of the fruit skin for the shortest period. Under field conditions, azoxystrobin, thiabendazole, difenoconazole+azoxystrobin and acibenzolar-S-methyl+azoxystrobin reduced the occurrence of diseased fruits, while anthracnose control was only obtained with azoxystrobin.

ASEA-ATOM's URANUS system for production control, economic control and safeguards

International Nuclear Information System (INIS)

Mattson, J.C.

1983-01-01

ASEA-ATOM needs a system for production and economic control because: (1) the uranium is the valuable property of the customer; (2) short delivery times are a prime means of competition; (3) the manufacture of fuel necessitates frequent enrichment changes and much enrichment blending; (4) minimizing uranium stock reduces interest costs. A system which meets the above needs will with minor modifications meet safeguard requirements. URANUS is an integrated man/computer system with manual input and automatic data treatment and reporting of information. The man/computer interface is monitored by the automatic checking for plausibility of all input. An item is a quantity of material which is treated as a unit in production. Each item receives a unique identification number which may be used only once. If the qualitative properties of an item are changed a new item number is issued. Items are reported on forms and fed into URANUS by authorized personnel using personal passwords or are directly reported by terminal from certain operations. Pertinent information is entered for each project. The URANUS computer system consists of terminal activated on-line and batch modules which are briefly described. Output is information for planning, economic control and safeguards. Safeguards information consists of the following. For flow and blending control: delivery information; change of nominal enrichment; enrichment blending; internal transactions that change an enrichment/origin account; material status report (MSR); item inventory per MBA; general ledger. For physical inventory: material balance report (MBR); book item inventory per MBA; physical item inventory per MBA; uranium balance per origin and enrichment

Towards benchmarking of multivariable controllers in chemical/biochemical industries: Plantwide control for ethylene glycol production

DEFF Research Database (Denmark)

Huusom, Jakob Kjøbsted; Bialas, Dawid Jan; Jørgensen, John Bagterp

2011-01-01

In this paper we discuss a simple yet realistic benchmark plant for evaluation and comparison of advanced multivariable control for chemical and biochemical processes. The benchmark plant is based on recycle-separator-recycle systems for ethylene glycol production and implemented in Matlab...... for education purposes (operator training, student education, etc) as well as scientific research into chemical process control where it enables rapid evaluation and comparison of advanced multivariable controllers as demonstrated in this study....

Dry Eye Post-Laser-Assisted In Situ Keratomileusis: Major Review and Latest Updates

Science.gov (United States)

Spierer, Oriel

2018-01-01

Dry eye is one of the most common complications occurring after laser-assisted in situ keratomileusis (LASIK), with virtually all patients experiencing some degree of postoperative dry eye symptoms. Enhanced understanding of the pathophysiology and mechanism of dry eye development in addition to preoperative screening of patients who are prone to dry eye is essential for better patient satisfaction and for improving short-term visual outcome postoperatively. This article reviews the latest studies published on LASIK-associated dry eye, including epidemiology, pathophysiology, risk factors, preoperative assessment, and management. PMID:29619255

21 CFR 111.55 - What are the requirements to implement a production and process control system?

Science.gov (United States)

2010-04-01

... production and process control system? 111.55 Section 111.55 Food and Drugs FOOD AND DRUG ADMINISTRATION... to Establish a Production and Process Control System § 111.55 What are the requirements to implement a production and process control system? You must implement a system of production and process...

Recent progress concerning the production of controlled highly oriented electrospun nanofibrous arrays

Science.gov (United States)

Manea, L. R.; Hristian, L.; Leon, A. L.; Popa, A.

2016-08-01

Among the foreground domains of all the research-development programs at national and international level, a special place is occupied by that concerning the nanosciences, nanotechnologies, new materials and technologies. Electrospinning found a well-deserved place in this space, offering the preparation of nanomaterials with distinctive properties and applications in medicine, environment, photonic sensors, filters, etc. These multiple applications are generated by the fact that the electrospinning technology makes available the production of nanofibers with controllable characteristics (length, porosity, density, and mechanical characteristics), complexity and architecture. The apparition of 3D printing technology favors the production of complex nanofibrous structures, controlled assembly, self-assembly of electrospun nanofibers for the production of scaffolds used in various medical applications. The architecture of fibrous deposits has a special influence on the subsequent development of the cells of the reconstructed organism. The present work proposes to study of recent progress concerning the production of controlled highly oriented electrospun nanofibrous arrays and progress in research on the production of complex 2D and 3D structures.

Heavy flavour production and spectroscopy at LHCb

CERN Document Server

INSPIRE-00258787

2012-01-01

At the Moriond QCD conference LHCb has presented results on heavy flavour production and spectroscopy. Here the latest results are discussed, which include the first observation and measurement of the branching fraction of the hadronic decay $B^+_e \\to J/\\psi\\pi^+ \\pi^- \\pi^+$, the mass measurement of the excited B mesons and the mass measurement of the $\\Xi_b$ and $\\Omega_b$ baryons.

RECONFIGURABLE PRODUCT ROUTING AND CONTROL FOR MASS CUSTOMISATION MANUFACTURING

Directory of Open Access Journals (Sweden)

A. J. Walker

2012-01-01

Full Text Available

ENGLISH ABSTRACT:Reconfigurable control of flexible manufacturing systems can allow for the efficient and responsive production of customised product instances. This can aid in providing make-to-order business models for various small- to medium-sized enterprises in South Africa, and provide competitive advantage in a dynamic global marketplace. Reconfigurable control application requires an understanding of the modes of production variability in mass customisation manufacturing. Temporally uncorrelated workflow routings are considered as one of these production variability modes. In this light, this paper addresses the flexible material payload routing problem, and presents a mobile robot platform that has been developed to research and design reconfigurable routing systems.

AFRIKAANSE OPSOMMING:Verstelbare beheer van aanpasbare vervaardigingstelsels kan die doeltreffende en reaktiewe produksie van doelgemaakte produkeksemplare toelaat. Hierdie beheer kan assisteer in die voorsiening van vervaardig-na-bestellingbesigheidsmodelle aan ’n aantal klein- tot medium-grootte ondernemings in Suid-Afrika, en aan hulle ’n kompeterende voorsprong bied in ’n dinamiese globale mark. Die instelling van verstelbare beheer vereis dat die modi van produkveranderlikheid in massa verbruikersaanpassingsvervaardiging verstaan word. Hierdie artikel spreek die probleem van aanpasbare roetebepaling van materiaalvragte in massa verbruikersaanpassingsvervaardiging aan. ’n Mobiele robot-platform, ontwikkel vir navorsing in verstelbare roetebepalingstelsels, word ook voorgelê.

Control of stored-product pests by irradiation

International Nuclear Information System (INIS)

Mahbub Hasan; Khan, A.R.

1998-01-01

The present review deals with the effects of irradiation on some aspects of the biology of major stored-product pests, namely mortality, stages of development, reproductive organs and reproductive potential, histology of the gut, factors influencing irradiation and the synergism of irradiation with other control agents. It also reports on the irradiation effects on stored commodities. Further guidelines for future research have been suggested. (author)

Product control of radioactive waste

International Nuclear Information System (INIS)

Warnecke, E.; Giller, H.

1989-09-01

The aim of the seminar was to give a survey of product quality control and to find out whether the producers/conditioners of waste set and fulfil requirements for the quality of the waste. The program included the following main areas: Random sample tests; Container tests; Process qualification and inspection, and Inspections of waste from fuel element reprocessing abroad. In other lectures, there are reports on measures for producers of waste for guaranteeing the final storage requirements, on quality assurance measurements in the conditioning of waste from large research establishments and from fuel element manufacture. The calling up of waste containers and the documentation of waste data is also introduced. (orig./HP) [de

Latest Development in Superconducting RF Structures for beta=1 Particle Acceleration

International Nuclear Information System (INIS)

Peter Kneisel

2006-01-01

Superconducting RF technology is since nearly a decade routinely applied to different kinds of accelerating devices: linear accelerators, storage rings, synchrotron light sources and FEL's. With the technology recommendation for the International Linear Collider (ILC) a year ago, new emphasis has been placed on improving the performance of accelerating cavities both in Q-value and in accelerating gradients with the goal to achieve performance levels close to the fundamental limits given by the material parameters of the choice material, niobium. This paper will summarize the challenges to SRF technology and will review the latest developments in superconducting structure design. Additionally, it will give an overview of the newest results and will report on the developments in alternative materials and technologies

Recent Results on Quarkonium and Beauty Production in pp collisions with the ATLAS Detector

CERN Document Server

Walder, James; The ATLAS collaboration

2017-01-01

The latest results from ATLAS on heavy flavour and quarkonium production, including exotic states, are presented. This talk includes the measurement of B-hadron pair production, presented as a function of a variety kinematic variables between the two B-hadrons, providing important inputs to modelling of production via gluon splitting. Additional Insight into QCD models of quarkonium production and double parton scattering is also presented, through the production cross-section measurement of di-Jpsi and effective cross-section from double parton scattering.

Agro. no 1 June Latest

African Journals Online (AJOL)

2017-06-01

Jun 1, 2017 ... Three products containing wheat flour: Moringa leaf fibre ratios of 100:0, 95:5, and ... composition of each of the products was determined and sensory evaluation of the ... Moringa leaf waste (100%) was obtained from the Moringa ... 72. Overall acceptability: The overall acceptability of the cookies followed ...

Unified Information Access in Product Creation with an Integrated Control Desk

Science.gov (United States)

Wrasse, Kevin; Diener, Holger; Hayka, Haygazun; Stark, Rainer

2017-06-01

Customers demand for individualized products leads to a large variety of different products in small series and single-unit production. A high flexibility pressure in product creation is one result of this trend. In order to counteract the pressure, the information steadily increasing by Industry 4.0 must be made available at the workplace. Additionally, a better exchange of information between product development, production planning and production is necessary. The improvement of individual systems, like CAD, PDM, ERP and MES, can only achieve this to a limited extent. Since they mostly use systems from different manufacturers, the necessary deeper integration of information is only feasible for SMEs to a limited extend. The presented control desk helps to ensure a more flexible product creation as well as information exchange. It captures information from different IT systems in the production process and presents them integrated, task-oriented and oriented to the user’s mental model, e.g. information of the production combined with the 3D model of product parts, or information about product development on the 3D model of the production. The solution is a digital 3D model of the manufacturing environment, which is enriched by billboards for a quick information overview and web service windows to access detailed MES and PDM information. By this, the level of abstraction can be reduced and reacts to changed requirements in the short term, making informed decisions. The interaction with the control stands utilizes the touch skills of mobile and fixed systems such as smartphones, tablets and multitouch tables.

Control of stored product pests by ionizing radiation

Science.gov (United States)

Food irradiation for prevention of food-borne illness and disinfestation of commodities of pests is increasing in a number of countries. The goal of this review is to analyze the literature and current use of irradiation to control stored-product pests and suggest research to optimize its potential....

Production controls (PC) and technical verification testing (TVT). A methodology for the control and tracking of LILW waste package conditioning

International Nuclear Information System (INIS)

Leon, A.M.; Nieto, J.L.L.; Garrido, J.G.

2003-01-01

As part of its low and intermediate level radioactive waste (LILW) characterisation and acceptance activities, ENRESA has set up a quality control programme that covers the different phases of radioactive waste package production and implies different levels of tracking in generation, assessment of activity and control of the documentation associated therewith. Furthermore, ENRESA has made available the mechanisms required for verification, depending on the results of periodic sampling, of the quality of the end product delivered by the waste producers. Both processes are included within the framework of two programmes of complementary activities: production controls (PC) and technical verification testing (TVT). (orig.)

Wind turbine control and monitoring

CERN Document Server

Luo, Ningsu; Acho, Leonardo

2014-01-01

Maximizing reader insights into the latest technical developments and trends involving wind turbine control and monitoring, fault diagnosis, and wind power systems, 'Wind Turbine Control and Monitoring' presents an accessible and straightforward introduction to wind turbines, but also includes an in-depth analysis incorporating illustrations, tables and examples on how to use wind turbine modeling and simulation software.   Featuring analysis from leading experts and researchers in the field, the book provides new understanding, methodologies and algorithms of control and monitoring, comput

Potential for widespread application of biological control of stored-product pests

DEFF Research Database (Denmark)

Hansen, Lise Stengaard

2007-01-01

Biological control of stored product pests has substantial potential in Europe". This is essentially the conclusion of the activities of a European working group funded by the COST system, an intergovernmental networking system. Working group 4 of COST action 842 (2000-2005) focussed on biologica...... for these situations will contribute to ensuring that stored food products are protected from insect and mite pests using techniques that are safe for consumers, workers and the environment.......Biological control of stored product pests has substantial potential in Europe". This is essentially the conclusion of the activities of a European working group funded by the COST system, an intergovernmental networking system. Working group 4 of COST action 842 (2000-2005) focussed on biological...

Statistical and Hydrological Evaluation of TRMM-Based Multi-Satellite Precipitation Analysis over the Wangchu Basin of Bhutan: Are the Latest Satellite Precipitation Products 3B42V7 Ready for Use in Ungauged Basins?

Science.gov (United States)

Xue, Xianwu; Hong, Yang; Limaye, Ashutosh S.; Gourley, Jonathan; Huffman, George J.; Khan, Sadiq Ibrahim; Dorji, Chhimi; Chen, Sheng

2013-01-01

The objective of this study is to quantitatively evaluate the successive Tropical Rainfall Measuring Mission (TRMM) Multi-satellite Precipitation Analysis (TMPA) products and further to explore the improvements and error propagation of the latest 3B42V7 algorithm relative to its predecessor 3B42V6 using the Coupled Routing and Excess Storage (CREST) hydrologic model in the mountainous Wangchu Basin of Bhutan. First, the comparison to a decade-long (2001-2010) daily rain gauge dataset reveals that: 1) 3B42V7 generally improves upon 3B42V6s underestimation both for the whole basin (bias from -41.15 to -8.38) and for a 0.250.25 grid cell with high-density gauges (bias from -40.25 to 0.04), though with modest enhancement of correlation coefficients (CC) (from 0.36 to 0.40 for basin-wide and from 0.37 to 0.41 for grid); and 2) 3B42V7 also improves its occurrence frequency across the rain intensity spectrum. Using the CREST model that has been calibrated with rain gauge inputs, the 3B42V6-based simulation shows limited hydrologic prediction NSCE skill (0.23 in daily scale and 0.25 in monthly scale) while 3B42V7 performs fairly well (0.66 in daily scale and 0.77 in monthly scale), a comparable skill score with the gauge rainfall simulations. After recalibrating the model with the respective TMPA data, significant improvements are observed for 3B42V6 across all categories, but not as much enhancement for the already well-performing 3B42V7 except for a reduction in bias (from -26.98 to -4.81). In summary, the latest 3B42V7 algorithm reveals a significant upgrade from 3B42V6 both in precipitation accuracy (i.e., correcting the underestimation) thus improving its potential hydrological utility. Forcing the model with 3B42V7 rainfall yields comparable skill scores with in-situ gauges even without recalibration of the hydrological model by the satellite precipitation, a compensating approach often used but not favored by the hydrology community, particularly in ungauged basins.

Dust control products at Hagerman National Wildlife Refuge, Texas: environmental safety and performance

Science.gov (United States)

Kunz, Bethany K.; Little, Edward E.

2015-01-01

Controlling fugitive dust while protecting natural resources is a challenge faced by all managers of unpaved roads. Unfortunately, road managers choosing between dust control products often have little objective environmental information to aid their decisions. To address this information gap, the U.S. Geological Survey and the U.S. Fish and Wildlife Service collaborated on a field test of three dust control products with the objectives of (a) evaluating product performance under real-world conditions, (b) verifying the environmental safety of products identified as practically nontoxic in laboratory tests, and (c) testing the feasibility of several environmental monitoring techniques for use in dust control tests. In cooperation with refuge staff and product vendors, three products (one magnesium chloride plus binder, one cellulose, and one synthetic fluid plus binder) were applied in July 2012 to replicated road sections at the Hagerman National Wildlife Refuge in Texas. These sections were monitored periodically for 12 months after application. Product performance was assessed by mobile-mounted particulate-matter meters measuring production of fugitive dust and by observations of road conditions. Environmental safety was evaluated through on-site biological observations and leaching tests with samples of treated aggregate. All products reduced dust and improved surface condition during those 12 months. Planned environmental measurements were not always compatible with day-to-day refuge management actions; this incompatibility highlighted the need for flexible biological monitoring plans. As one of the first field tests of dust suppressants that explicitly incorporated biological endpoints, this effort provides valuable information for improving field tests and for developing laboratory or semifield alternatives.

Workable methods for risks control in the food chain production.

Directory of Open Access Journals (Sweden)

Lucilla Iacumin

2008-04-01

Full Text Available Several food pathologies due to new or already known micro-organisms occur all over the world every year. Food concerned are more and more frequently traditional typical, ethnical products coming from fast or slow food systems. Most of food-borne pathologies develop through neurological, gastrointestinal (watery, bloody or persistent diarrhoea abdominal pain, sickness and vomiting. The causes of these epidemics, apart from the concerned pathogen, are linked to the contaminated first matter or to contaminations occurred during food processing and consequently due to the lack of employment of the most fundamental sanitary measures and to non-control of the critical points of the HACCP (Hazard Analysis Critical Control Point systems. The pre-requirements to promote food health consist of the implementation of good agriculture husbandry and production practices, the use of HACCP systems, the training of the workers employed in the different productive rows and in the adoption of identification and traceability systems. The EU implemented the so-called hygiene pack, that is a list of rules imposing food control in each processing, marketing and consumption phase, from husbandry or cropping to consumer’s table, to promote health in food (circulating all over Europe.

Economic potentials of oil palm products and weed control on ...

African Journals Online (AJOL)

A study was carried out at the Research Farm of National Root Crops Research Institute Umudike, southeastern Nigeria (05o, 29'N, 07o 33'E and 122 m above sea level), in 2015 and 2016 cropping seasons to study the economic potentials of oil palm products and weed control on sustainable turmeric production and some ...

Photochemical production of ozone and control strategy for Southern Taiwan

Science.gov (United States)

Shiu, Chein-Jung; Liu, Shaw Chen; Chang, Chih-Chung; Chen, Jen-Ping; Chou, Charles C. K.; Lin, Chuan-Yao; Young, Chea-Yuan

An observation-based method (OBM) is developed to evaluate the ozone (O 3) production efficiency (O 3 molecules produced per NO x molecule consumed) and O 3 production rate ( P(O 3)) during a field campaign in southern Taiwan. The method can also provide an estimate of the concentration of OH. A key step in the method is to use observed concentrations of two aromatic hydrocarbons, namely ethylbenzene and m, p-xylene, to estimate the degree of photochemical processing and amounts of photochemically consumed NO x and NMHCs by OH. In addition, total oxidant (O 3+NO 2) instead of O 3 itself turns out to be very useful for representing ozone production in the OBM approach. The average O 3 production efficiency during the field campaign in Fall (2003) is found to be about 10.2±3.9. The relationship of P(O 3) with NO x is examined and compared with a one-dimensional (1D) photochemical model. Values of P(O 3) derived from the OBM are slightly lower than those calculated in the 1D model. However, OH concentrations estimated by the OBM are about a factor of 2 lower than the 1D model. Fresh emissions, which affect the degree of photochemical processing appear to be a major cause of the underestimate. We have developed a three-dimensional (3D) OBM O 3 production diagram that resembles the EKMA ozone isopleth diagram to study the relationship of the total oxidant versus O 3 precursors. The 3D OBM O 3 production diagram suggests that reducing emissions of NMHCs are more effective in controlling O 3 than reducing NO x. However, significant uncertainties remain in the OBM, and considerable more work is required to minimize these uncertainties before a definitive control strategy can be reached. The observation-based approach provides a good alternative to measuring peroxy radicals for evaluating the production of O 3 and formulating O 3 control strategy in urban and suburban environments.

Use a renewable energy sources and latest power-saving technologies in the the Republic Kazakstan

International Nuclear Information System (INIS)

Gulevich, N.V.

1996-01-01

The subject of alternative power in Kazakstan is brought up. Wind-, hydro-, solar power, biogas installation can improve the Republic power base. The main directions of activity of A. Einstein International Power engineering Academy on involving renewable energy sources and latest power-saving technologies to Republic of Kazakstan's fuel-power balance is given. It should be noted that renewable power engineering usually handles reversible energy sources and reserved power cycles. (author)

Control of the dehydration process in production of intermediate-moisture meat products: a review.

Science.gov (United States)

Chang, S F; Huang, T C; Pearson, A M

1996-01-01

IM meat products are produced by lowering the aw to 0.90 to 0.60. Such products are stable at ambient temperature and humidity and are produced in nearly every country in the world, especially in developing areas where refrigeration is limited or unavailable. Traditionally IM meats use low cost sources of energy for drying, such as sun drying, addition of salt, or fermentation. Products produced by different processes are of interest since they do not require refrigeration during distribution and storage. Many different IM meat products can be produced by utilizing modern processing equipment and methods. Production can be achieved in a relatively short period of time and their advantages during marketing and distribution can be utilized. Nevertheless, a better understanding of the principles involved in heat transfer and efficiency of production are still needed to increase efficiency of processing. A basic understanding of the influence of water vapor pressure and sorption phenomena on water activity can materially improve the efficiency of drying of IM meats. Predrying treatments, such as fermentation and humidity control, can also be taken advantage of during the dehydration process. Such information can lead to process optimization and reduction of energy costs during production of IM meats. The development of sound science-based methods to assure the production of high-quality and nutritious IM meats is needed. Finally, such products also must be free of pathogenic microorganisms to assure their success in production and marketing.

Real Time Part Input Control of a Pull Production System by Finding IF-THEN Rules

Science.gov (United States)

Ramli, Rizauddin; Yamamoto, Hidehiko; Abu Qudeiri, Jaber

This paper considers the part input problem of a production system where two Flexible Transfer Lines (FTLs) consisting of an up-stream production line and a down-stream production line while operating under Just In Time (JIT) production management. The up-stream production line processes the raw material after receiving them from suppliers, and after processing them, delivers the processed product to a down-stream production line via a conveyer. In this paper, we have proposed a novel idea for a part input real time control system, known as Algorithm for Real Time Control of Part Input Systems (ARTCOPS). The algorithm is useful when FTLs are in operation under a production order that is different from the pre-decided production schedule. Simulations of virtual production systems have been carried out to verify that ARTCOPS is useful in real time control, although the production orders are different from the pre-decided production scheduling.

Constraining viscous dark energy models with the latest cosmological data

Science.gov (United States)

Wang, Deng; Yan, Yang-Jie; Meng, Xin-He

2017-10-01

Based on the assumption that the dark energy possessing bulk viscosity is homogeneously and isotropically permeated in the universe, we propose three new viscous dark energy (VDE) models to characterize the accelerating universe. By constraining these three models with the latest cosmological observations, we find that they just deviate very slightly from the standard cosmological model and can alleviate effectively the current H_0 tension between the local observation by the Hubble Space Telescope and the global measurement by the Planck Satellite. Interestingly, we conclude that a spatially flat universe in our VDE model with cosmic curvature is still supported by current data, and the scale invariant primordial power spectrum is strongly excluded at least at the 5.5σ confidence level in the three VDE models as the Planck result. We also give the 95% upper limits of the typical bulk viscosity parameter η in the three VDE scenarios.

Digital control in nuclear power plants

International Nuclear Information System (INIS)

Bouzon, B.

1984-01-01

This document presents the latest automatic control structures used in the programmable control systems of 13.00 MW nuclear power plants constructed by Electricite de France. The impact of this technological innovation goes beyond a straightforward design modification; in addition to the new range of processes made possible, it permits far-reaching changes in the working method employed at the design office and in the field. (author)

Evaluation of pull production control strategies under uncertainty: An integrated fuzzy AHP-TOPSIS approach

Directory of Open Access Journals (Sweden)

Aydin Torkabadi

2018-03-01

Full Text Available Purpose: Just-In-Time (JIT production has continuously been considered by industrial practitioners and researchers as a leading strategy for the yet popular Lean production. Pull Production Control Policies (PPCPs are the major enablers of JIT that locally control the level of inventory by authorizing the production in each station. Aiming to improve the PPCPs, three authorization mechanisms: Kanban, constant-work-in-process (ConWIP, and a hybrid system, are evaluated by considering uncertainty. Design/methodology/approach: Multi-Criteria Decision Making (MCDM methods are successful in evaluating alternatives with respect to several objectives. The proposed approach of this study applies the fuzzy set theory together with an integrated Analytical Hierarchy Process (AHP and a Technique for Order Performance by Similarity to Ideal Solution (TOPSIS method. Findings: The study finds that hybrid Kanban-ConWIP pull production control policies have a better performance in controlling the studied multi-layer multi-stage manufacturing and assembly system. Practical implications: To examine the approach a real case from automobile electro mechanical part production industry is studied. The production system consists of multiple levels of manufacturing, feeding a multi-stage assembly line with stochastic processing times to satisfy the changing demand. Originality/value: This study proposes the integrated Kanban-ConWIP hybrid pull control policies and implements several alternatives on a multi-stage and multi-layer manufacturing and assembly production system. An integrated Fuzzy AHP TOPSIS method is developed to evaluate the alternatives with respect to several JIT criteria.

Particulars of Demand for Agricultural Products in the Domestic Market

Directory of Open Access Journals (Sweden)

Laura Catalina TIMIRAS

2012-11-01

Full Text Available Based on the latest official statistics on food and beverage purchases, overall and by product category, the article captures quantitative and qualitative changes in recent years on the Romanian market for this category of goods. It has been also highlighted the gaps observed in the different categories of households by: living environment, presence and number of children, employment status and age of household head, all from the perspective of the demand for those products.

Latest Insights on Adenovirus Structure and Assembly

Directory of Open Access Journals (Sweden)

Carmen San Martín

2012-05-01

Full Text Available Adenovirus (AdV capsid organization is considerably complex, not only because of its large size (~950 Å and triangulation number (pseudo T = 25, but also because it contains four types of minor proteins in specialized locations modulating the quasi-equivalent icosahedral interactions. Up until 2009, only its major components (hexon, penton, and fiber had separately been described in atomic detail. Their relationships within the virion, and the location of minor coat proteins, were inferred from combining the known crystal structures with increasingly more detailed cryo-electron microscopy (cryoEM maps. There was no structural information on assembly intermediates. Later on that year, two reports described the structural differences between the mature and immature adenoviral particle, starting to shed light on the different stages of viral assembly, and giving further insights into the roles of core and minor coat proteins during morphogenesis [1,2]. Finally, in 2010, two papers describing the atomic resolution structure of the complete virion appeared [3,4]. These reports represent a veritable tour de force for two structural biology techniques: X-ray crystallography and cryoEM, as this is the largest macromolecular complex solved at high resolution by either of them. In particular, the cryoEM analysis provided an unprecedented clear picture of the complex protein networks shaping the icosahedral shell. Here I review these latest developments in the field of AdV structural studies.

Operational aspects of the radiological control in a radioisotopes plant production

International Nuclear Information System (INIS)

Corahua, A.

1996-01-01

The purpose of this paper is to inform about the results obtained in the control operations carried out by the radioprotection area of the radioisotopes plant production during 1994 and then were compared with the limits established by the regulations of radiological radioprotection. In the general inter-texture of the activities that are developed in the radioisotopes plant production, the carried out controls are: area monitoring, air monitoring, personnel monitoring, monitoring in the expedition of radioactive material and monitoring and control in the evacuation of solid and liquid wastes. The result obtained in the present paper states that the doses received by the exposed occupationally staff are below the allowed limits. (author). 3 refs

Electroweak boson production at LHCb

CERN Document Server

Sestini, Lorenzo

2018-01-01

The LHCb experiment offers a complementary phase space to ATLAS and CMS to study electroweak processes, thanks to the forward acceptance and the large bandwidth of the trigger allowing low energy thresholds. For this reason electroweak measurements at LHCb can provide unique constraints to the Parton Distribution Functions. Moreover these measurements can be used to validate reconstruction techniques. In these proceedings the latest measurements on W and Z bosons production performed during the LHC Run I and Run II data taking are presented.

Latest MIG, TIG arc-YAG laser hybrid welding systems for various welding products

Science.gov (United States)

Ishide, Takashi; Tsubota, Shuho; Watanabe, Masao

2003-03-01

Laser welding is capable of high-efficiency low-strain welding, and so its applications are started to various products. We have also put the high-power YAG laser of up to 10 kW to practical welding use for various products. On the other hand the weakest point of this laser welding is considered to be strict in the welding gap aiming allowance. In order to solve this problem, we have developed hybrid welding of TIG, MIG arc and YAG laser, taking the most advantages of both the laser and arc welding. Since the electrode is coaxial to the optical axis of the YAG laser in this process, it can be applied to welding of various objects. In the coaxial MIG, TIG-YAG welding, in order to make irradiation positions of the YAG laser beams having been guided in a wire or an electrode focused to the same position, the beam transmitted in fibers is separated to form a space between the separated beams, in which the laser is guided. With this method the beam-irradiating area can be brought near or to the arc-generating point. This enables welding of all directions even for the member of a three-dimensional shape. This time we carried out welding for various materials and have made their welding of up to 1 mm or more in welding groove gap possible. We have realized high-speed 1-pass butt welding of 4m/min in welding speed with the laser power of 3 kW for an aluminum alloy plate of approximately 4 mm thick. For a mild steel plate also we have realized butt welding of 1m/min with 5 kW for 6 mm thick. Further, in welding of stainless steel we have shown its welding possibility, by stabilizing the arc with the YAG laser in the welding atmosphere of pure argon, and shown that this welding is effective in high-efficiency welding of various materials. Here we will report the fundamental welding performances and applications to various objects for the coaxial MIG, TIG-YAG welding we have developed.

Enabling People with Developmental Disabilities to Actively Perform Designated Occupational Activities according to Simple Instructions with a Nintendo Wii Remote Controller by Controlling Environmental Stimulation

Science.gov (United States)

Shih, Ching-Hsiang; Wang, Shu-Hui; Chang, Man-Ling; Shih, Ching-Hsiang

2012-01-01

The latest researches have adopted software technology, turning the Nintendo Wii Remote Controller into a high performance three-dimensional object orientation detector. This study extended Wii Remote Controller functionality to assess whether two people with developmental disabilities would be able to actively perform designated simple…

Characteristics in mineral compositions of lunar latest mare volcanism revealed from spectral data

Science.gov (United States)

Kato, S.; Morota, T.; Yamaguchi, Y.; Watanabe, S.; Otake, H.; Ohtake, M.; Nimura, T.

2016-12-01

Lunar mare basalts provide insights into the composition and thermal history of the lunar mantle. According to crater counting analysis with remote sensing data, the ages of mare basalts suggest a first peak of magma activity at 3.2-3.8 Ga and a second peak at 2 Ga. In order to understand the mechanism for causing the second peak and its magma source, we reassess the correlation between the titanium contents and the eruption ages of mare basalt units using the compositional and chronological data updated by SELENE (Kaguya). In the Procellarum KREEP Terrane, where the latest mare basalt units are concentrated, an increase in the mean titanium content is observed in the Eratosthenian Period, as reported by previous studies. We found that, however, a rapid increase in mean titanium content occurred near 2.3 Ga. This result suggests that the magma source of the mare basalts changed at this particular age. Moreover, the high-titanium basaltic eruptions are correlated with the second peak in mare volcanism at 2 Ga. The latest mare volcanism may have been induced by a super-hot plume originating from the core-mantle boundary. In this study, to reveal the difference between the volcanic activities before and after 2.3 Ga, we developed the method to estimate the mineral components and elemental compositions of lunar mare basalts by using the Kaguya Spectral Profiler data. We will introduce the detail of the method and discuss about the difference between the mineral compositions of mare basalts before and after 2.3 Ga based on our preliminary results.

Mandatory Production Controls. Issues in Agricultural Policy. Agriculture Information Bulletin Number 520.

Science.gov (United States)

Economic Research Service (USDA), Washington, DC.

Mandatory restrictions on agricultural production continue to be suggested as an alternative policy for reducing price-depressing surplus production, increasing farm income, and cutting farm program costs. A mandatory production control program (MPCP) can be implemented through two methods: (1) acreage allotments, which restrict individual farmers…

Latest Results on 2-FGHP Tetrode To Fulfill ITER ICRH Requirements

International Nuclear Information System (INIS)

Robert, Ch.

2006-01-01

The requirements for the RF generation of ITER ICRH include several parameters that are not compatible for a tetrode to fulfill. High power, from 1.7 to 2.5 MW according to the ICRH design options, have to combined with, both, a cw operation (more than 1000 seconds of continuous running time) and a high VSWR (higher than 1:2.0), over the required frequency range of 40 to 56 MHz. The proposed paper will overview the existing tetrodes on the market used in similar type of operations, i.e. in fusion applications. This analysis shows clearly the limitations of the conventional tetrode technology that can only fulfill some of the ICRH requirements, but not all together. The first part of the paper will describe the latest results on conventional tetrodes, after years of operation at TORE SUPRA and JET, for which tetrodes such as TH 525 and TH 526 are used. The results clearly indicate that tetrodes are well suited for Fusion applications but not with the combination of parameters necessary for ITER ICRH. The second part will describe the extended performance tetrodes, based on a Double Folded Grid High Performance (2-FGHP) tetrode technology, used for scientific and TV broadcast applications for years. This 2-FGHP concept extends drastically the performance of tetrodes, either in terms of frequency, or power or pulse duration, allowing such tetrodes to be used in ITER. The third part shows results of operation in these scientific and broadcast areas of 2-FGHP tetrodes in order to demonstrate the advantages of this technology over conventional tetrodes. Real operation data allow to give performance together with duration of operation in full service, on a 24 hour per day basis. Finally the last part will be dedicated to present the latest results obtained in a Fusion type tests at Thales Electron Devices in 2006 of a 2-FGHP tetrode. These results show the possibilities of this technology to fulfill ITER ICRH requirements and its capabilities to allow some evolutions of

Advanced process monitoring and feedback control to enhance cell culture process production and robustness.

Science.gov (United States)

Zhang, An; Tsang, Valerie Liu; Moore, Brandon; Shen, Vivian; Huang, Yao-Ming; Kshirsagar, Rashmi; Ryll, Thomas

2015-12-01

It is a common practice in biotherapeutic manufacturing to define a fixed-volume feed strategy for nutrient feeds, based on historical cell demand. However, once the feed volumes are defined, they are inflexible to batch-to-batch variations in cell growth and physiology and can lead to inconsistent productivity and product quality. In an effort to control critical quality attributes and to apply process analytical technology (PAT), a fully automated cell culture feedback control system has been explored in three different applications. The first study illustrates that frequent monitoring and automatically controlling the complex feed based on a surrogate (glutamate) level improved protein production. More importantly, the resulting feed strategy was translated into a manufacturing-friendly manual feed strategy without impact on product quality. The second study demonstrates the improved process robustness of an automated feed strategy based on online bio-capacitance measurements for cell growth. In the third study, glucose and lactate concentrations were measured online and were used to automatically control the glucose feed, which in turn changed lactate metabolism. These studies suggest that the auto-feedback control system has the potential to significantly increase productivity and improve robustness in manufacturing, with the goal of ensuring process performance and product quality consistency. © 2015 Wiley Periodicals, Inc.

Searches for electroweak production of supersymmetric gauginos and sleptons with the ATLAS detector

CERN Document Server

Kourkoumeli-Charalampidi, Athina; The ATLAS collaboration

2017-01-01

The latest results of the electroweak production of Supersymmetric particles is presented. The searches are based on the integrated luminosity of 36.1 fb^{-1} of pp collisions collected at \\sqrt{s} = 13 TeV by the ATLAS experiment at the LHC.

ANALYSIS OF ACCURACY OF MODIS BRDF PRODUCT (MCD43 C6) BASED ON MISR LAND SURFACE BRF PRODUCT – A CASE STUDY OF THE CENTRAL PART OF NORTHEAST ASIA

OpenAIRE

Li, J.; Chen, S.; Qin, W.; Murefu, M.; Wang, Y.; Yu, Y.; Zhen, Z.

2018-01-01

EOS/MODIS land surface Bi-directional Reflectance Distribution Function (BRDF) product (MCD43), with the latest version C6, is one of the most important operational BRDF products with global coverage. The core sub-product MCD43A1 stores 3 parameters of the RossThick-LiSparseR semi-empirical kernel-driven BRDF model. It is important for confident use of the product to evaluate the accuracy of bi-directional reflectance factor (BRF) predicted by MCD43A1 BRDF model (mBRF). A typical region in th...

Agents Modeling Experience Applied To Control Of Semi-Continuous Production Process

Directory of Open Access Journals (Sweden)

Gabriel Rojek

2014-01-01

Full Text Available The lack of proper analytical models of some production processes prevents us from obtaining proper values of process parameters by simply computing optimal values. Possible solutions of control problems in such areas of industrial processes can be found using certain methods from the domain of artificial intelligence: neural networks, fuzzy logic, expert systems, or evolutionary algorithms. Presented in this work, a solution to such a control problem is an alternative approach that combines control of the industrial process with learning based on production results. By formulating the main assumptions of the proposed methodology, decision processes of a human operator using his experience are taken into consideration. The researched model of using and gathering experience of human beings is designed with the contribution of agent technology. The presented solution of the control problem coincides with case-based reasoning (CBR methodology.

A Novel Enclosed Online Control System for Microalgae Production

Directory of Open Access Journals (Sweden)

Bin Li

2014-03-01

Full Text Available Microalgae are single celled microscopic organisms which, like plants, convert solar energy into bio-energy through photosynthesis. They can be used to produce a variety of bio-based products, such as bio-food and biodiesel. Large scale algae production can be achieved in open or closed systems. An enclosed online microalgae control production system is presented in this paper. The designed system is composed of a reactor which is placed inside a box with light reflecting surface. Lighting system, CO2 supply, heating, as well as online cell mass monitoring via spectrophotometer, were integrated. The online monitoring of cell mass concentration is coupled to two pumps which remove a certain amount of cell suspension, and take fresh media as an alternative. Also, a LabView program was developed to collect data from a spectrophotometer and processed in a computer. Considering the limited experimental conditions and the pollution possibility for its high productivity if liquid is not properly disposed, food color was used to test the designed novel system in this paper. The results showed that, the system could detect a change in absorption over time with periodic sampling for every 4.8 minutes. When absorption value reach a pre-set gate, pump1 immediately starts to pump out a certain amount of solution?then pump2 starts to pump in fresh media according to the calculated time. The concentration could be controlled below the threshold value. From the continuous test using food color, the designed system showed good stability and controlling accuracy. It provides a good reference for the following microalgae testing experiment in future. Considering the applications of microalgae in agriculture, this research also provides resources for bio-fertilizer.

Control strategies for crane systems: A comprehensive review

Science.gov (United States)

Ramli, Liyana; Mohamed, Z.; Abdullahi, Auwalu M.; Jaafar, H. I.; Lazim, Izzuddin M.

2017-10-01

Crane systems are tremendously utilised in numerous heavy load transportation industries, and therefore, the control of crane systems is a well-established research field. As the last review paper was published more than a decade ago, there is a lack of collected and organised information regarding the latest and the newest updates on control strategies for crane control systems. Hence, this paper presents a comprehensive review of crane control strategies discussing the latest research works during the years from 2000 to 2016. Various crane types and control issues are highlighted, followed by the main focus of this paper, an extensive review of the control schemes for diverse types of crane systems that have been carried out in the 21st century. A brief review on modelling of single-pendulum and double-pendulum crane systems is also given. In addition, anti-sway control systems for industrial cranes that are available on the market is described. This paper summarises most of the related work and also pays a special focus on research trends regarding the control of crane systems that have been previously published in the literature. It is envisaged that this review paper will be helpful to new researchers when identifying research directions for this particular area of interest.

Latest News

CERN Multimedia

Miele, P.

B0 TOROID MODEL COIL The B0 toroid model coil was successfully tested with magnetic mirror at nominal current I=20.5 kA, up to a maximum current Imax=24 kA to verify a 10% BT force load current. An extensive campaign of measurements act to characterize the mechanical, thermal, electrical and magnetic properties of the coil was performed in the period April-Dec 2001, and handling and assembly trials to exercise BT underground installation were done in the period Jan-Feb 2002. NEW LAYOUT OF BT INTEGRATION - TESTING IN BUILDING 180 Integration 1 and Integration 2 of the BT coils, which are the assembly of the double pancakes into the coil casing (cold mass), and the assembly of the cold mass and related components into the vacuum vessel respectively, are both performed in Building 180. Thereafter the integrated coils are tested with magnetic mirror in the test bench. A new organizational scheme and detailed working plan are under definition to prepare and optimize the space available. BT PRODUCTION ...

Contemporary perspective on plaque control.

Science.gov (United States)

Marsh, P D

2012-06-22

The aim of this review article is to provide a scientific platform that will enable the dental team to develop a rational approach to plaque control based on the latest knowledge of the role of the oral microflora in health and disease. The resident oral microflora is natural and forms spatially-organised, interactive, multi-species biofilms on mucosal and dental surfaces in the mouth. These resident oral microbial communities play a key function in the normal development of the physiology of the host and are important in preventing colonisation by exogenous and often undesirable microbes. A dynamic balance exists between the resident microflora and the host in health, and disease results from a breakdown of this delicate relationship. Patients should be taught effective plaque control techniques that maintain dental biofilms at levels compatible with oral health so as to retain the beneficial properties of the resident microflora while reducing the risk of dental disease from excessive plaque accumulation. Antimicrobial and antiplaque agents in oral care products can augment mechanical plaque control by several direct and indirect mechanisms that not only involve reducing or removing dental biofilms but also include inhibiting bacterial metabolism when the agents are still present at sub-lethal concentrations.

How NASA KSC Controls Interfaces with the use of Motion Skeletons and Product Structure

Science.gov (United States)

Jones, Corey

2013-01-01

This presentation will show how NASA KSC controls interfaces for Modular Product Architecture (MPA) using Locator Skeletons, Interface Skeletons, and Product Structure, to be combined together within a Motion Skeleton. The user will learn how to utilize skeleton models to communicate interface data, as successfully done at NASA KSC in their use of Motion Skeletons to control interfaces for multi-launch systems. There will be discussion of the methodology used to control design requirements through WTParts, and how to utilize product structure for non-CAD documents.

Underlying Factors for Practicality of the Production Control Systems

DEFF Research Database (Denmark)

Arica, Emrah; Strandhagen, Jan Ola; Hvolby, Hans-Henrik

2012-01-01

and communication technology, coordination and feedback, human factors and decision making, and measurement are the identified factors to be taken into account. Industrial interviews with three case companies, that are participating to the research program called The Norwegian Manufacturing Future (SFI NORMAN......This paper gives indications to important factors that must be considered for effectiveness of the production control systems under uncertainty. Five key factors have been identified by the literature study. Production schedule generation and execution approach under uncertainty, information...

The extended range neutron rem counter LINUS: overview and latest developments

International Nuclear Information System (INIS)

Birattari, C.; Rancati, T.; Esposito, A.; Pelliccioni, M.; Ferrari, A.; Silari, M.

1997-01-01

The 'history' of the extended range neutron rem counter LINUS, since its first conception in 1990 is reviewed, along with the latest developments. These include the calibration of the initially cylindrical version with nearly monoenergetic neutrons in the energy range 34-66 MeV, a detailed evaluation of the anisotropy of its response function, the construction and calibration of an improved spherical version, and recent measurements in reference high energy stray radiation fields. The instrument can now be considered as being fully characterized. Similar monitors built by other laboratories following the present design have confirmed its performances. The instrument is now in semi-routine use at a number of particle accelerator facilities and is one of several devices used on-board of aircrafts for assessing the exposure to cosmic rays at commercial flight altitudes. (author)

New control system for BR2. Preventive approach to process control

International Nuclear Information System (INIS)

Van den Branden, G.; Koonen, E.

2011-01-01

In 1961, the BR2 reactor became critical for the first time. Yet the multi-functional research reactor at SCK-CEN is not out of date, quite the contrary. Regular upgrades and innovations keep the reactor in step with the latest advancements in technology. In 2010, the control system of BR2, a vital part of the reactor, was replaced as a preventive measure.

Asthma control and productivity loss in those with work-related asthma: A population-based study.

Science.gov (United States)

Wong, Alyson; Tavakoli, Hamid; Sadatsafavi, Mohsen; Carlsten, Chris; FitzGerald, J Mark

2017-06-01

In Canada, asthma is the third leading cause of work loss, yet little is known about the associated productivity loss. The goal of this study was to look at the relationship between asthma control and productivity loss, particularly contrasting those with work-related asthma (WRA) and non-work-related asthma (NWRA). A population-based random sample of adults with asthma in British Columbia, Canada, was prospectively recruited. Asthma control was graded according to Global Initiative for Asthma classification, while productivity loss and presence of WRA was assessed using questionnaires. Ordinal regression models were then used to associate WRA with asthma control. Generalized linear models were applied to estimate the average productivity loss associated with different levels of asthma control among those with WRA and NWRA. The study included 300 employed adults. Sixty (20%) had WRA. The odds of being controlled were significantly lower in those with WRA (OR = 0.23, 95% CI: 0.09, 0.56; P asthma had a significant difference in productivity loss due to presenteeism ($659.1 [95% CI: 12.9, 1581.5; P = 0.04]), but not absenteeism ($88.7 [95% CI: -86.5, 279.6; P = 0.35]), when compared to those with NWRA and uncontrolled asthma. There was no significant difference when a similar comparison was made for those with controlled or partially controlled asthma. WRA is associated with worse asthma control and increased productivity loss. Presenteeism makes a significant contribution to productivity loss and should be considered when evaluating the overall economic burden of asthma, particularly WRA.

Recombinant proteins from plants: production and isolation of clinically useful compounds

National Research Council Canada - National Science Library

Cunningham, Charles; Porter, Andrew J. R

1998-01-01

... of recombinant proteins for use as specialist industrial or therapeutic biomolecules. The intention of Recombinant Proteins from Plants is to provide comprehensive and detailed protocols covering all the latest molecular approaches. Because the production oftransgenic plants has become routine in many laboratories, coverage is also given to some of the more "...

Analysis and control of Boolean networks a semi-tensor product approach

CERN Document Server

Cheng, Daizhan; Li, Zhiqiang

2010-01-01

This book presents a new approach to the investigation of Boolean control networks, using the semi-tensor product (STP), which can express a logical function as a conventional discrete-time linear system. This makes it possible to analyze basic control problems.

Temperature-dependent dynamic control of the TCA cycle increases volumetric productivity of itaconic acid production by Escherichia coli.

Science.gov (United States)

Harder, Björn-Johannes; Bettenbrock, Katja; Klamt, Steffen

2018-01-01

Based on the recently constructed Escherichia coli itaconic acid production strain ita23, we aimed to improve the productivity by applying a two-stage process strategy with decoupled production of biomass and itaconic acid. We constructed a strain ita32 (MG1655 ΔaceA Δpta ΔpykF ΔpykA pCadCs), which, in contrast to ita23, has an active tricarboxylic acid (TCA) cycle and a fast growth rate of 0.52 hr -1 at 37°C, thus representing an ideal phenotype for the first stage, the growth phase. Subsequently we implemented a synthetic genetic control allowing the downregulation of the TCA cycle and thus the switch from growth to itaconic acid production in the second stage. The promoter of the isocitrate dehydrogenase was replaced by the Lambda promoter (p R ) and its expression was controlled by the temperature-sensitive repressor CI857 which is active at lower temperatures (30°C). With glucose as substrate, the respective strain ita36A grew with a fast growth rate at 37°C and switched to production of itaconic acid at 28°C. To study the impact of the process strategy on productivity, we performed one-stage and two-stage bioreactor cultivations. The two-stage process enabled fast formation of biomass resulting in improved peak productivity of 0.86 g/L/hr (+48%) and volumetric productivity of 0.39 g/L/hr (+22%) in comparison to the one-stage process. With our dynamic production strain, we also resolved the glutamate auxotrophy of ita23 and increased the itaconic acid titer to 47 g/L. The temperature-dependent activation of gene expression by the Lambda promoters (p R /p L ) has been frequently used to improve protein or, in a few cases, metabolite production in two-stage processes. Here we demonstrate that the system can be as well used in the opposite direction to selectively knock-down an essential gene (icd) in E. coli to design a two-stage process for improved volumetric productivity. The control by temperature avoids expensive inducers and has the

Latest progress of BIGH3 gene in corneal diseases and diabetic retinopathy

Directory of Open Access Journals (Sweden)

Fan-Qian Song

2017-03-01

Full Text Available BIGH3 gene plays an important role in ocular diseases. On the one hand, it is closely related to the occurrence of corneal diseases. BIGH3 gene can inhibit corneal neovascularization, lead to corneal dystrophy, participate in keratoconus formation. On the other hand, it can lead to the formation of neovascularization in diabetic retinopathy. The latest experiments show that TGF beta secreted by macrophages can promote the expression of BIGH3 mRNA and BIGH3 protein, and promote apoptosis of retinal endothelial cells and pericytes, which leads to the formation of neovascularization in diabetic retinopathy. This article will describe the new progress of BIGH3 gene in ocular diseases from several aspects as mentioned above.

Ocean anoxia did not cause the Latest Permian Extinction

Science.gov (United States)

Proemse, Bernadette C.; Grasby, Stephen E.; Wieser, Michael E.; Mayer, Bernhard; Beauchamp, Benoit

2014-05-01

The Latest Permian Extinction (LPE, ~252 million years ago) was a turning point in the history of life on Earth with a loss of ~96% of all marine species and ~70% of all terrestrial species. While, the event undoubtedly shaped the evolution of life its cause remains enigmatic. A leading hypothesis is that the global oceans became depleted in oxygen (anoxia). In order to test this hypothesis we investigated a proxy for marine oxygen levels (molybdenum isotopic composition) in shale across the LPE horizon located on the subtropical northwest margin of Pangea at that time. We studied two sedimentary records in the Sverdrup basin, Canadian High Arctic: Buchanan Lake (eastern Axel Heiberg Island; 79° 26.1'N, 87° 12.6'W), representing a distal deep-water slope environment, and West Blind Fiord (southwest Ellesmere Island; 78° 23.9'N, 85° 57.2'W), representing a deep outer shelf environment (below storm wave base). The molybdenum isotopic composition (δ98/95Mo) of sediments has recently become a powerful tool as a paleo-oceanographic proxy of marine oxygen levels. Sample preparation was carried out in a metal-free clean room facility in the isotope laboratory of the Department of Physics and Astronomy, University of Calgary, Canada, that is supplied by HEPA-filtered air. Molybdenum isotope ratios were determined on a Thermo Scientific multi-collector inductively coupled plasma mass spectrometer (MC-ICP-MS) with an uncertainty better than ±0.10o for δ98/95Mo values. Results from the Buchanan Lake section show a large shift in δ98/95Mo values from 2.02o to +2.23o at the extinction horizon, consistent with onset of euxinic conditions. In contrast, West Blind Fiord shales, representing the sub-storm wave base shelf environment, show little change in the molybdenum isotopic composition (1.34o to +0.05), indicating ongoing oxic conditions across the LPE (Proemse et al., 2013). Our results suggest that areas of the Pangea continental shelf (North West Pangea) experienced

Design of Control System for Flexible Packaging Bags Palletizing Production Line Based on PLC

Science.gov (United States)

Zheng, Huiping; Chen, Lin; Zhao, Xiaoming; Liu, Zhanyang

Flexible packaging bags palletizing production line is to put the bags in the required area according to particular order and size, in order to finish handling, storage, loading and unloading, transportation and other logistics work of goods. Flexible packaging bags palletizing line is composed of turning bags mechanism, shaping mechanism, indexing mechanism, marshalling mechanism, pushing bags mechanism, pressing bags mechanism, laminating mechanism, elevator, tray warehouse, tray conveyor and loaded tray conveyor. Whether the whole production line can smoothly run depends on each of the above equipment and precision control among them. In this paper the technological process and the control logic of flexible packaging bags palletizing production line is introduced. Palletizing process of the production line realized automation by means of a control system based on programmable logic controller (PLC). It has the advantages of simple structure, reliable and easy maintenance etc.

Formulation and quality control of a topical gel product for treatment of melasmaFormulation and quality control of a topical gel product for treatment of melasma

Directory of Open Access Journals (Sweden)

A. Ketabi

2017-11-01

Full Text Available Background and objectives: Melasma is one of the most common pigmentary disorders. It has a considerable impact on quality of life. The treatment of melasma has still remained a challenge because the efficient treatment has not been proven until now and there is still a need to find new depigmenting products.Allium cepa L. and Cucumis melo L. seeds as well as tragacanth have been introduced in Iranian traditional medicine (ITM as depigmenting agents. Moreover, modern studies have shown their antioxidant and inhibitory mushroom tyrosinase effect.In this study, a topical gel containing Allium cepa L. and Cucumis melo L. seeds extract was prepared with tragacanth and quality control evaluations have been accomplished. Method: After performing quality control of plants seeds and tragacanth according to pharmacopoeia, the ethanol extract of A. cepa and hydroalcoholic extract of C. melo seeds were prepared. An appropriate gel formulation was selected on the base of suitable viscosity. The gel product was formulated using 5% of each plant extracts in tragacanth gel base. In addition, the herbal gel was evaluated using pharmaceutical behavior such as physical appearance, pH, viscosity, spreadability as well as phenolics content. Results: The herbal gel product showed acceptable pharmaceutical behavior as well as considerable phenolic content (1.43±0.01 mg/g. Conclusion: The prepared topical gel product could be a good natural formulation candidate for clinical studies in the field of hyperpigmentation. Moreover, phenolic content of the product could be considered as an indicator for its quality control.

Wind farms production: Control and prediction

Science.gov (United States)

El-Fouly, Tarek Hussein Mostafa

Wind energy resources, unlike dispatchable central station generation, produce power dependable on external irregular source and that is the incident wind speed which does not always blow when electricity is needed. This results in the variability, unpredictability, and uncertainty of wind resources. Therefore, the integration of wind facilities to utility electrical grid presents a major challenge to power system operator. Such integration has significant impact on the optimum power flow, transmission congestion, power quality issues, system stability, load dispatch, and economic analysis. Due to the irregular nature of wind power production, accurate prediction represents the major challenge to power system operators. Therefore, in this thesis two novel models are proposed for wind speed and wind power prediction. One proposed model is dedicated to short-term prediction (one-hour ahead) and the other involves medium term prediction (one-day ahead). The accuracy of the proposed models is revealed by comparing their results with the corresponding values of a reference prediction model referred to as the persistent model. Utility grid operation is not only impacted by the uncertainty of the future production of wind farms, but also by the variability of their current production and how the active and reactive power exchange with the grid is controlled. To address this particular task, a control technique for wind turbines, driven by doubly-fed induction generators (DFIGs), is developed to regulate the terminal voltage by equally sharing the generated/absorbed reactive power between the rotor-side and the gridside converters. To highlight the impact of the new developed technique in reducing the power loss in the generator set, an economic analysis is carried out. Moreover, a new aggregated model for wind farms is proposed that accounts for the irregularity of the incident wind distribution throughout the farm layout. Specifically, this model includes the wake effect

Control of Listeria species food safety at a poultry food production facility.

Science.gov (United States)

Fox, Edward M; Wall, Patrick G; Fanning, Séamus

2015-10-01

Surveillance and control of food-borne human pathogens, such as Listeria monocytogenes, is a critical aspect of modern food safety programs at food production facilities. This study evaluated contamination patterns of Listeria species at a poultry food production facility, and evaluated the efficacy of procedures to control the contamination and transfer of the bacteria throughout the plant. The presence of Listeria species was studied along the production chain, including raw ingredients, food-contact, non-food-contact surfaces, and finished product. All isolates were sub-typed by pulsed-field gel electrophoresis (PFGE) to identify possible entry points for Listeria species into the production chain, as well as identifying possible transfer routes through the facility. The efficacy of selected in-house sanitizers against a sub-set of the isolates was evaluated. Of the 77 different PFGE-types identified, 10 were found among two or more of the five categories/areas (ingredients, food preparation, cooking and packing, bulk packing, and product), indicating potential transfer routes at the facility. One of the six sanitizers used was identified as unsuitable for control of Listeria species. Combining PFGE data, together with information on isolate location and timeframe, facilitated identification of a persistent Listeria species contamination that had colonized the facility, along with others that were transient. Copyright © 2015 Elsevier Ltd. All rights reserved.

Isotope methods for the control of food products and beverages

Energy Technology Data Exchange (ETDEWEB)

Guillou, C; Reniero, F [Commission of the European Communities, Joint Research Centre, Ispra (Italy)

2001-10-01

The measurement of the stable isotope contents provides useful information for the detection of many frauds in food products. Nuclear magnetic resonance (NMR) and isotopic ratio mass spectroscopy (IRMS) are the two main analytical techniques used for the determination of stable isotope contents in food products. These analytical techniques have been considerably improved in the last years offering wider possibilities of applications for food analysis. A review of the applications for the control of food products and beverages is presented. The need for new reference materials is discussed. (author)

Isotope methods for the control of food products and beverages

International Nuclear Information System (INIS)

Guillou, C.; Reniero, F.

2001-01-01

The measurement of the stable isotope contents provides useful information for the detection of many frauds in food products. Nuclear magnetic resonance (NMR) and isotopic ratio mass spectroscopy (IRMS) are the two main analytical techniques used for the determination of stable isotope contents in food products. These analytical techniques have been considerably improved in the last years offering wider possibilities of applications for food analysis. A review of the applications for the control of food products and beverages is presented. The need for new reference materials is discussed. (author)

Research of Control System and Fault Diagnosis of the Sound-absorbing Board Production Line

Directory of Open Access Journals (Sweden)

Yanjun Xiao

2014-08-01

Full Text Available Programmable Logic Controller is the core of the control system of the sound- absorbing board production line and the design of fault diagnosis is an essential modules in the sound- absorbing board production line. The article discourses the application of PLC in the control system of the production line, and designs the methods of grading treatment and prevention of troubles, which makes use of PLC’S logic functions. The method has good expansibility, and has good guidance to the fault diagnosis in other automation equipments.

Learning control for riser-slug elimination and production-rate optimization for an offshore oil and gas production process

DEFF Research Database (Denmark)

Pedersen, Simon; Løhndorf, Petar Durdevic; Yang, Zhenyu

2014-01-01

, (ii) maximizing the production rate at the riser of an offshore production platform, by manipulating a topside choke valve through a learning switching model-free PID controller. The results show good steady-state performance, though a long settling time due to the unknown reference for no slugging...

Model Predictive Engine Air-Ratio Control Using Online Sequential Relevance Vector Machine

Directory of Open Access Journals (Sweden)

Hang-cheong Wong

2012-01-01

Full Text Available Engine power, brake-specific fuel consumption, and emissions relate closely to air ratio (i.e., lambda among all the engine variables. An accurate and adaptive model for lambda prediction is essential to effective lambda control for long term. This paper utilizes an emerging technique, relevance vector machine (RVM, to build a reliable time-dependent lambda model which can be continually updated whenever a sample is added to, or removed from, the estimated lambda model. The paper also presents a new model predictive control (MPC algorithm for air-ratio regulation based on RVM. This study shows that the accuracy, training, and updating time of the RVM model are superior to the latest modelling methods, such as diagonal recurrent neural network (DRNN and decremental least-squares support vector machine (DLSSVM. Moreover, the control algorithm has been implemented on a real car to test. Experimental results reveal that the control performance of the proposed relevance vector machine model predictive controller (RVMMPC is also superior to DRNNMPC, support vector machine-based MPC, and conventional proportional-integral (PI controller in production cars. Therefore, the proposed RVMMPC is a promising scheme to replace conventional PI controller for engine air-ratio control.

Constraining viscous dark energy models with the latest cosmological data

Energy Technology Data Exchange (ETDEWEB)

Wang, Deng [Nankai University, Theoretical Physics Division, Chern Institute of Mathematics, Tianjin (China); Yan, Yang-Jie; Meng, Xin-He [Nankai University, Department of Physics, Tianjin (China)

2017-10-15

Based on the assumption that the dark energy possessing bulk viscosity is homogeneously and isotropically permeated in the universe, we propose three new viscous dark energy (VDE) models to characterize the accelerating universe. By constraining these three models with the latest cosmological observations, we find that they just deviate very slightly from the standard cosmological model and can alleviate effectively the current H{sub 0} tension between the local observation by the Hubble Space Telescope and the global measurement by the Planck Satellite. Interestingly, we conclude that a spatially flat universe in our VDE model with cosmic curvature is still supported by current data, and the scale invariant primordial power spectrum is strongly excluded at least at the 5.5σ confidence level in the three VDE models as the Planck result. We also give the 95% upper limits of the typical bulk viscosity parameter η in the three VDE scenarios. (orig.)

Latest experiences and future plans on NSLS-II insertion devices

Energy Technology Data Exchange (ETDEWEB)

Tanabe, T.; Hidaka, Y.; Kitegi, C.; Hidas, D.; Musardo, M.; Harder, D. A.; Rank, J.; Cappadoro, P.; Fernandes, H.; Corwin, T. [Energy Sciences Directorate, Brookhaven National Laboratory, Upton, NY 11973, U.S.A (United States)

2016-07-27

National Synchrotron Light Source-II (NSLS-II) is the latest storage ring of 3 GeV energy at the Brookhaven National Laboratory (BNL). The horizontal emittance of the electron beam with the currently installed six damping wigglers is 0.9 nm.rad, which could be further reduced to 0.5 nm.rad with more insertion devices (IDs). With only one RF cavity the beam current is restricted to 200 mA. Five hundred mA operation is envisaged for next year with an addition of the second cavity. Six (plus two branches) beamlines have been commissioned in the initial phase of the project. In July 2015, three NIH funded beamlines called “Advanced Beamlines for Biological Investigations with X-rays” (ABBIX) will be added for operation. This paper describes the experiences of ID development, installation, and commissioning for the NSLS-II project as well as our future plans to improve the performance of the facility in terms of source development.

Model-based control of hopper dredgers

NARCIS (Netherlands)

Braaksma, J.

2008-01-01

The modern trailing suction hopper dredgers are advanced ships that are equipped with many automation systems that can be controlled with integrated computer systems from the bridge. From the operators it is expected that they generate the right set-points for all these systems. The latest ships are

Hitachi's proposed DCS solution for new build CANDU EC6 using the G-HIACS unified platform

Energy Technology Data Exchange (ETDEWEB)

Tan, D.; Ishii, K.; Otsuka, Y.; Uemura, K., E-mail: daisuke.tan.ye@hitachi.com [Hitachi Ltd., Infrastructure Systems Co., Ibaraki (Japan); Marko, P.E. [Hitachi Power Systems Canada Ltd., Power and Industry Div., Ontario (Canada)

2013-07-01

Hitachi Ltd. has developed the safe and secure functional safety DCS controller for potential new build NPP projects in the global market. Hitachi has improved the availability, maintainability, and reliability for its latest DCS systems named G-HIACS. In this latest paper on its DCS product development program, Hitachi would like to report a proposed DCS solution for new build CANDU NSP and BOP based on the G-HIACS Unified Architecture (R800FS/HSC800FS vSAFE Functional Safety Controller and R900/HSC900 General Purpose Controller) hybrid control system. (author)

Feedforward Control of a 3-D Physiological Articulatory Model for Vowel Production

Institute of Scientific and Technical Information of China (English)

FANG Qiang; Akikazu Nishikido; Jianwu Dang

2009-01-01

A three-dimensional (3-D) physiological articulatory model was developed to account for the bio-mechanical properties of the speech organs in speech production. Control of the model to investigate the mechanism of speech production requires an efficient control module to estimate muscle activation patterns, which is used to manipulate the 3-D physiological arUculatory model, according to the desired articulatory posture. For this purpose, a feedforward control strategy was developed by mapping the articulatory target to the corresponding muscle activation pattern via the intrinsic representation of vowel articulation. In this process, the articulatory postures are first mapped to the corresponding intrinsic representations; then, the articulatory postures are clustered in the intrinsic representations space and a nonlinear function is ap-proximated for each cluster to map the intrinsic representation of vowel articulation to the muscle activation pattern by using general regression neural networks (GRNN). The results show that the feedforward control module is able to manipulate the 3-D physiological articulatory model for vowel production with high accu-racy both acoustically and articulatodly.

Searches for HH production at 13 TeV with the CMS detector

CERN Document Server

Dall'Osso, Martino

2017-01-01

The production of a pair of Higgs bosons provides a direct handle on the structure of the Higgs field potential. While the Higgs boson pair production within the Standard Model is very small and essentially out of experimental reach in the LHC Run II, several Standard Model extensions foresee an enhancement that can be already probed with the available data. The latest searches for resonant and non-resonant Higgs pair production made using CMS Run II data are presented considering different decay modes of the Higgs boson.

Design control considerations for biologic-device combination products.

Science.gov (United States)

Anderson, Dave; Liu, Roger; Anand Subramony, J; Cammack, Jon

2017-03-01

Combination products are therapeutic and diagnostic medical products that combine drugs, devices, and/or biological products with one another. Historically, biologics development involved identifying efficacious doses administered to patients intravenously or perhaps by a syringe. Until fairly recently, there has been limited focus on developing an accompanying medical device, such as a prefilled syringe or auto-injector, to enable easy and more efficient delivery. For the last several years, and looking forward, where there may be little to distinguish biologics medicines with relatively similar efficacy profiles, the biotechnology market is beginning to differentiate products by patient-focused, biologic-device based combination products. As innovative as biologic-device combination products are, they can pose considerable development, regulatory, and commercialization challenges due to unique physicochemical properties and special clinical considerations (e.g., dosing volumes, frequency, co-medications, etc.) of the biologic medicine. A biologic-device combination product is a marriage between two partners with "cultural differences," so to speak. There are clear differences in the development, review, and commercialization processes of the biologic and the device. When these two cultures come together in a combination product, developers and reviewers must find ways to address the design controls and risk management processes of both the biologic and device, and knit them into a single entity with supporting product approval documentation. Moreover, digital medicine and connected health trends are pushing the boundaries of combination product development and regulations even further. Despite an admirable cooperation between industry and FDA in recent years, unique product configurations and design features have resulted in review challenges. These challenges have prompted agency reviewers to modernize consultation processes, while at the same time, promoting

Elastic-plastic fracture analysis of carbon steel piping using the latest CEGB R6 approach

International Nuclear Information System (INIS)

Kanno, S.; Hasegawa, K.; Shimizu, T.; Kobayashi, H.

1991-01-01

The elastic-plastic fracture of carbon steel piping having various pipe diameters and circumferential crack angles and subjected to a bending moment is analyzed using the latest United Kingdom Central Electricity Generating Board R6 approach. The elastic-plastic fracture criterion must be applied instead of the plastic collapse criterion with increase of the pipe diameter and the crack angle. A simplified elastic-plastic fracture analysis procedure based on the R6 approach is proposed. (author)

Production of exotic and conventional quarkonia and open beauty/open charm at ATLAS

CERN Document Server

C. Bini; The ATLAS collaboration

2016-01-01

The ATLAS experiment at LHC is carrying on a wide programme to study the production properties of conventional and exotic quarkonium, beauty, and charm bound states. The latest results on J/$\\psi$, $\\psi$(2s) and X(3872) production at 7, 8, and 13 TeV, together with D meson production with Run-1 are presented. Studies of associated production of charmonium with vector bosons, searches for exotic states in the bottomonium sector and a new measurement of the ratio of b-quark fragmentation functions are also briefly presented.

Tumour characteristics and survival in patients with invasive interval breast cancer classified according to mammographic findings at the latest screening

DEFF Research Database (Denmark)

Vitak, B; Olsen, K E; Månson, J C

1999-01-01

with invasive interval cancer detected from May 1978 to August 1995 (n = 544). The tumours were evaluated with regard to age, radiological category, interval between the latest screen and diagnosis and tumour characteristics at the time of diagnosis. We investigated possible relationships between the survival...... screen and diagnosis were not genuine predictors of the prognosis in patients with invasive interval breast cancer. No certain prognostic difference existed between true interval cancers and overlooked or misinterpreted interval breast cancers, despite higher proportions of grade-I tumours, ER positive......The aim of this study was to investigate whether different mammographic categories of interval cancer classified according to findings at the latest screening are associated with different distributions of prognostic factors or with different survival rates. The series consisted of all patients...

Estimating Latest Cretaceous and Tertiary Atmospheric PCO2 from Stomatal Indices

Science.gov (United States)

Royer, D. L.; Wing, S. L.; Beerling, D. J.

2001-05-01

Most modern C3 seed plants show an inverse relationship between PCO2 and stomatal index (SI), where SI is the proportion of epidermal cells that are stomatal packages. This plant-atmosphere response therefore provides a reliable approach for estimating paleo-CO2 levels. Since stomatal responses to CO2 are generally species-specific, one is limited in paleo-reconstructions to species that exist both in the fossil record and living today. Fossils morphologically similar to living Ginkgo biloba and Metasequoia glyptostroboides extend back to the early and late Cretaceous, respectively, indicating that the fossil and living forms are very closely related. Measurements of SI made on fossil Ginkgo and Metasequoia were calibrated with historical collections of G. biloba and M. glyptostroboides leaves from sites that developed during the anthropogenically-driven CO2 increases of the past 145 years (288-369 ppmv) and with saplings of G. biloba and M. glyptostroboides grown in CO2 controlled growth chambers (350-800 ppmv). Both nonlinear regressions are highly significant (Ginkgo: n = 40, r2 = 0.91; Metasequoia: n = 18; r2 = 0.85). Results from a sequence of 23 latest Cretaceous to early Eocene-aged Ginkgo-bearing sites indicate that CO2 remained between 300 and 450 ppmv with the exception of one high estimate ( ~800 ppmv) near the Paleocene/Eocene boundary, and results from 4 middle Miocene-aged Ginkgo- and Metasequoia-bearing sites indicate that CO2 was between 320 and 400 ppmv. If correct, the CO2 values estimated here are too low to explain via the CO2 greenhouse effect alone the higher global mean temperatures (e.g., 3-4 ° C for the early Eocene) inferred from models and geological data for these two intervals.

Case-specific comparison of water pollution control alternatives in peat production

International Nuclear Information System (INIS)

Savolainen, M.; Kaasinen, A.; Heikkinen, K.; Ihme, R.; Kaemae, T.; Alasaarela, E.

1996-01-01

The present practice water pollution control in peat production and the elements of planning were analyzed, the water purification methods were classified and their weaknesses estimated. Furthermore, the cost of the water purification constructions was estimated and their significance for the watercourses evaluated. 54 peat production plans were chosen from the catchment areas of the rivers Iijoki, Siikajoki and Pyhaejoki. The suitability of the chosen water pollution control methods was evaluated on the basis of the plans and, further, on the basis of field surveys. The suitability of the purification methods to practical water pollution control was assessed by making plans for 15 peat mining areas. There is a need to develop the planning and implementation of water pollution control in peat mining. The methods that are used do not always work in the expected way in practice. Despite this planning is compatible with the water protection program and the regulations that are in force. The study gives a good idea of how to update the planning instructions for water pollution control. The accompanying report includes plan for 11 peat mining areas. (orig.)

2011 International Conference in Electrics, Communication and Automatic Control Proceedings

CERN Document Server

2012-01-01

This two-volume set contains the very latest, cutting-edge material in electrics, communication and automatic control. As a vital field of research that is highly relevant to current developments in a number of technological domains, the subjects it covers include micro-electronics and integrated circuit control, signal processing technology, next-generation network infrastructure, wireless communication and scientific instruments. The aim of the International Conference in Electrics, Communication and Automatic Control, held in Chongqing, China, in June 2011 was to provide a valuable inclusive platform for researchers, engineers, academicians and industrial professionals from all over the world to share their research results with fellow scientists in the sector. The call for papers netted well over 600 submissions, of which 224 were selected for presentation. This fully peer-reviewed collection of papers from the conference can be viewed as a single-source compendium of the latest trends and techniques in t...

Documenting control system functionality for digital control implementations

International Nuclear Information System (INIS)

Harber, J.; Borairi, M.; Tikku, S.; Josefowicz, A.

2006-01-01

In past CANDU designs, plant control was accomplished by a combination of digital control computers, analogue controllers, and hardwired relay logic. Functionality for these various control systems, each using different hardware, was documented in varied formats such as text based program specifications, relay logic diagrams, and other various specification documents. The choice of formats was influenced by the hardware used and often required different specialized skills for different applications. The programmable electronic systems in new CANDU designs are realized in a manner consistent with latest international standards (e.g., the IEC 61513 standard). New CANDU designs make extensive use of modern digital control technology, with the benefit that functionality can be implemented on a limited number of control platforms, reducing development and maintenance cost. This approach can take advantage of tools that allow the plant control system functional and performance requirements to be documented using graphical representations. Modern graphical methods supplemented by information databases can be used to provide a clear and comprehensive set of requirements for software and system development. Overview diagrams of system functionality provide a common understanding of the system boundaries and interfaces. Important requirements are readily traced through the development process. This improved reviewability helps to ensure consistency with the safety and and production design requirements of the system. Encapsulation of commonly used functions into custom-defined function blocks, such as typical motor control centre interfaces, process interlocks, median selects etc, eases the burden on designers to understand and analyze the detailed functionality of each instance of use of this logic. A library of encapsulated functions will be established for complex functions that are reused in the control logic development. By encapsulation and standardisation of such

24 CFR 3280.308 - Formaldehyde emission controls for certain wood products.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Formaldehyde emission controls for certain wood products. 3280.308 Section 3280.308 Housing and Urban Development Regulations Relating to... Body and Frame Construction Requirements § 3280.308 Formaldehyde emission controls for certain wood...

Crude oil derived petroleum products in the aquatic environment: priorities for control

International Nuclear Information System (INIS)

Grimwood, M.J.

2001-01-01

The available data on the environmental fate, behaviour and toxicity of five groups of petroleum products is reviewed and the information used to identify the priority of oil products for pollution control to protect the aquatic environment. The oil product groups comprise gasolines, kerosenes, other light fuel oil distillates, residual heavy fuel oils and lubricating oils. (author)

Model based fleet optimisation and master control of a power production system

International Nuclear Information System (INIS)

Joergensen, C.; Mortensen, J.H.; Nielsen, E.O.; Moelbak, T.

2006-01-01

This paper discussed an optimization concept for power plants operated by the Danish power company Elsam. The power company operates a distributed power production system with fossil fuel thermal plants, biomass-fired thermal plants, waste incineration plants, on- and offshore wind power, and district heating storage units. Power and regulation power are traded on an hourly basis, while trading of district heating resources is conducted using bilateral contracts. System and plant level case studies on optimization and control were presented. A system control level was developed to ensure compliance with power market requirements. Dynamic constraints were posed by environmental regulations, grid capabilities, and fuel and district heating contracts. System components included a short-term load scheduler; a power controller; a frequency control scheduler; a marginal cost calculator; and a master control. The scheduler consisted of an optimization algorithm and a set of steady-state models designed to minimize fuel, load, and maintenance costs. Quadratic programming and mixed integer programming methods were used to minimize deviations between the total electrical power production reference value and actual power production values. The study showed that control levels can be optimized using advanced modelling and control methods. However, integration and coordination between the various levels is needed to obtain improved performance. It was concluded that a bottom-up approach starting at the lowest possible level can ensure the performance of an optimization scheme. 6 refs., 9 figs

High resolution sea-level curve for the latest Frasnian and earliest Famennian derived for high frequency sequences in the Appalachian Basin

Energy Technology Data Exchange (ETDEWEB)

Filer, J.K. (Washington and Lee Univ., Lexington, VA (United States). Dept. of Geology)

1992-01-01

Siliciclastic sequences have been mapped in the subsurface and outcrop of much of the Appalachian basin in facies ranging from shale in the basin plain to shelf sandstone. Eleven transgressive/regressive cycles have been defined in an estimated 1.5 to 2.0 Ma period in the latest Frasnian and earliest Famennian, and range in duration from about 75,000 to 400,000 years. Lithofacies maps, covering most of the basin, were prepared for each sequence. These maps show both the area of basinal black shale deposition, which defines the base of each cycle, and the areal extent of subsequent clinoform siltstone and shelf sandstone deposition in the upper portion of each cycle. The stratigraphic patterns show two stacked sets of progradational basinwide sequences. Geographic scale of the study precludes autocyclic controls of cycles. Sea-level/climate cycles, probably superimposed on longer term tectonic cycles, are the proposed cause of these observed depositional patterns. Removal of the long-term progradational trend of Upper Devonian basin filling results in a proposed eustatic sea-level curve (Johnson and others (1985)) reveals correspondence of three regressive maxima in both models. The curve presented here reveals that an ongoing process of higher frequency sea-level modification was active at this time. Higher frequency sea-level events, nested within previously interpreted lower frequency global events, are inferred to also be eustatic. Models of a biotic crises which occurs at this time should consider the implications of these high frequency sea-level cycles. The patterns observed are consistent with latest Frasnian initiation of glaciation in South America. This would be somewhat earlier than has generally been accepted.

Prevalence of tabacco product use in Latvia and control measures

Directory of Open Access Journals (Sweden)

Kokarevica A.

2012-10-01

Full Text Available The use of tobacco products is a major problem having a serious effect on public health. Deaths from external causes are those that can be prevented by ensuring environmental safety and educating the society about the effect of lifestyle habits and behaviour on health of an individual. Not only research data reveal the prevalence of tobacco use but also the rate of tobacco sales. Tobacco industry marketing includes advertising, sales promotion and sponsorship strategies that are aimed at promotion of tobacco use. Demand for tobacco products is influenced also by changes in legislation relating to ban on tobacco advertising and sponsorship. Therefore it is necessary to introduce an agreed strategy for reducing tobacco use. The countries that have ratified the World Health Organisation (WHO Framework Convention on Tobacco Control (the Convention should develop and implement an effective tobacco control programme. In Latvia the number of daily smokers gradually decreases thanks to the extensive smoking restrictions though tobacco manufacturers use all the available media, radio and television, newspapers, magazines, advertisements and Internet, to advertise their products. Therefore in order to combat the prevalence of smoking first of all it is necessary to limit cigarette marketing and sales and to carry out monitoring and development of tobacco control measures on the state level. The sales of legal cigarettes have decreased in Latvia starting from 2009. However, the increase in tax rates and prices has contributed to the movement of illegal goods therefore it is necessary to take additional restrictive measures concerning the movement of illegal goods. Though amendments to legislation of Latvia relating to tobacco control comply with the requirements of the WHO Convention it is necessary to evaluate the efficiency of control measures and to improve them. Systematic and comprehensive education of the public is required to encourage the change of

Continued slide seen for C.I.S. oil production

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that oil production in the Commonwealth of Independent States may dip to 7.7 million b/d next year. Robert Ebel of the Center for strategic and International Studies, Washington, D.C., made that prediction before a meeting of the National Association of Petroleum Investment Analysts. Oil and Gas Journal's latest worldwide oil production figures peg the C.I.S. volume at 8.689 million b/d last August. Ebel said a September decree will allow oil prices to move in line with the market and with costs of production. That in turn will lead to development of a deregulated domestic oil market

A comprehensive review of the implementation of hazard analysis critical control point (HACCP) to the production of flour and flour-based products.

Science.gov (United States)

Arvanitoyannis, Ioannis S; Traikou, Athina

2005-01-01

The production of flour and semolina and their ensuing products, such as bread, cake, spaghetti, noodles, and corn flakes, is of major importance, because these products constitute some of the main ingredients of the human diet. The Hazard Analysis Critical Control Point (HACCP) system aims at ensuring the safety of these products. HACCP has been implemented within the frame of this study on various products of both Asian and European origin; the hazards, critical control limits (CCLs), observation practices, and corrective actions have been summarized in comprehensive tables. Furthermore, the various production steps, packaging included, were thoroughly analyzed, and reference was made to both the traditional and new methodologies in an attempt to pinpoint the occurring differences (advantages and disadvantages) per process.

Indoor Radon and Its Decay Products: Concentrations, Causes, and Control Strategies

Energy Technology Data Exchange (ETDEWEB)

Nero, A.V.; Gadgil, A.J.; Nazaroff, W.W.; Revzan, K.L.

1990-01-01

This report is an introduction to the behavior of radon 222 and its decay products in indoor air. This includes review of basic characteristics of radon and its decay products and of features of the indoor environment itself, all of which factors affect behavior in indoor air. The experimental and theoretical evidence on behavior of radon and its decay products is examined, providing a basis for understanding the influence of geological, structural, and meteorological factors on indoor concentrations, as well as the effectiveness of control techniques. We go on to examine three important issues concerning indoor radon. We thus include (1) an appraisal of the concentration distribution in homes, (2) an examination of the utility and limitations of popular monitoring techniques and protocols, and (3) an assessment of the key elements of strategies for controlling radon levels in homes.

Production and quality control of 66 Ga as a PET radioisotope

International Nuclear Information System (INIS)

Rowshanfarzad, P.; Jalilian, A. R.; Akhlaghi, M.; Sabet, M.

2004-01-01

Background: 66 Ga (t 1/2 =9.49 h, β + : 4.153 MeV, γ: 511, 834, 1039, 2752 keV) has a wide range of applications in different fields of medical sciences. Production of 66 Ga became one of our main interests, according to its increasing applications in nuclear medicine, particularly in PET imaging. Materials and Methods: 66 Zn (p,n) 66 Ga reaction was determined as the best choice for the production of 66 Ga, according to the present facilities and conditions. The bombardment was performed by 15 MeV protons in Cyclone 30-IBA accelerator with a current intensity of 180 μA for 67 min. ALICE nuclear code and SRIM nuclear program were used to determine the optimum energy and target thickness. Targets were prepared by electroplating of 66 Zn (>95%) on a copper backing. Chemical processing was performed by a no carrier added method consisting of ion exchange chromatography and liquid-liquid extraction. Anion exchange chromatography was used for the recovery of target material. Quality control of the product was carried out in two steps of chemical and radionuclidic purity control. Results: the activity of 66 Ga was 2.41 Ci at the end of bombardment and the production yield was 12.04 mCi/μAh. The chemical separation yield was 93% and the yield of chemical recovery of the target material was 97%. Quality control tests showed a radionuclidic purity of more than 97% and the amounts of chemical impurities were in accordance with standard levels. Discussion: Our production yield was comparable with previous reports given in the literature. The chemical separation method used in this research was simple and brought up acceptable results. So, this process can be considered as one of the best choices for the production of 66 Ga

Nuclear reactor and production systems with digital controls

International Nuclear Information System (INIS)

Luger, P.P.

1976-01-01

Several digital sensing devices are described for use in automated production systems. The first described is for use in the automatic operation of a reactor. This device employs a binant electrometer using a quartz fiber mounted at one end but free to vibrate at the other in an AC field. The fiber oscillates if a charge is placed upon it. An optical slit replaces the ordinary eyepiece reticule scale. With the quartz fiber adjusted so its image is in focus at the optical slit, photoelectric signals are obtained at null charge on the fiber. The quartz fiber is repeatedly charged and allowed to discharge by collecting ions from a source under measurement. Each photoelectric signal causes a digital time reading to be taken. The time readings are used to evaluate the current due to the collected charge. The photoelectric signals, by feedback, also operate the electrometer for continuous or intermittent-continuous operation. Basically, the system is a current digitizer. Application is made to reactor monitoring and control as well as to other types of production systems. Finally, other types of sensing devices are also described and their use in automated controlled processes is shown. 3 claims, 19 figures

Visual control as a key factor in a production process of a company from automotive branch

Directory of Open Access Journals (Sweden)

Stanisław Borkowski

2013-04-01

Full Text Available This article presents a theoretical basis for one type of control in enterprises – visual control. It presents the meaning of visual control in the Toyota Production System and BOST researches as a tool of measure, among other things, the importance of visual control in production companies. The level of importance of visual control usage as one of the production process elements in the analysed company was indicated. The usage of visual control is a main factor in a production process of the analyzed company, the factor which provides continuous help to employees to check whether the process differs from the standard. The characteristic progression of production process elements was indicated and the SW factor (the use of visual control took the third place, PE factor (interruption of production when it detects a problem of quality turned out to be the most important one, while the least important was the EU factor (granting power of attorney down. The main tools for this evaluation: an innovative BOST survey - Toyota's management principles in questions, in particular, the Pareto-Lorenz diagram, radar graph and series of importance as graphical interpretation tools, were used to present the importance of each factor in relation to individual assessments.

Diagnostic value of Pentraxin-3 in patients with sepsis and septic shock in accordance with latest sepsis-3 definitions.

Science.gov (United States)

Hamed, Sonja; Behnes, Michael; Pauly, Dominic; Lepiorz, Dominic; Barre, Max; Becher, Tobias; Lang, Siegfried; Akin, Ibrahim; Borggrefe, Martin; Bertsch, Thomas; Hoffmann, Ursula

2017-08-09

Pentraxin-3 (PTX-3) is an acute-phase protein involved in inflammatory and infectious processes. This study assesses its diagnostic and prognostic value in patients with sepsis or septic shock in a medical intensive care unit (ICU). The study includes 213 ICU patients with clinical criteria of sepsis and septic shock. 77 donors served as controls. Plasma levels of PTX-3, procalcitonin (PCT) and interleukin-6 were measured on day 1, 3 and 8. PTX-3 correlated with higher lactate levels as well as with APACHE II and SOFA scores (p = 0.0001). PTX-3 levels of patients with sepsis or septic shock were consistently significantly higher than in the control group (p ≤ 0.001). Plasma levels were able to discriminate sepsis and septic shock significantly on day 1, 3 and 8 (range of AUC 0.73-0.92, p = 0.0001). Uniform cut-off levels were defined at ≥5 ng/ml for at least sepsis, ≥9 ng/ml for septic shock (p = 0.0001). PTX-3 reveals diagnostic value for sepsis and septic shock during the first week of intensive care treatment, comparable to interleukin-6 according to latest Sepsis-3 definitions. NCT01535534 . Registered 14.02.2012.

Weed Control Strategies for Organic Peanut Production and Transition: A Lesson in Basic Agronomy

Science.gov (United States)

Weed control in organic peanut production is difficult and costly. The only production inputs that consistently improved weed management in organic peanut production were modified production practices and intense cultivation with a tine weeder. Research trials evaluated row patterns, seeding rates...

A simple model-based control for Pichia pastoris allows a more efficient heterologous protein production bioprocess.

Science.gov (United States)

Cos, Oriol; Ramon, Ramon; Montesinos, José Luis; Valero, Francisco

2006-09-05

A predictive control algorithm coupled with a PI feedback controller has been satisfactorily implemented in the heterologous Rhizopus oryzae lipase production by Pichia pastoris methanol utilization slow (Mut(s)) phenotype. This control algorithm has allowed the study of the effect of methanol concentration, ranging from 0.5 to 1.75 g/L, on heterologous protein production. The maximal lipolytic activity (490 UA/mL), specific yield (11,236 UA/g(biomass)), productivity (4,901 UA/L . h), and specific productivity (112 UA/g(biomass)h were reached for a methanol concentration of 1 g/L. These parameters are almost double than those obtained with a manual control at a similar methanol set-point. The study of the specific growth, consumption, and production rates showed different patterns for these rates depending on the methanol concentration set-point. Results obtained have shown the need of implementing a robust control scheme when reproducible quality and productivity are sought. It has been demonstrated that the model-based control proposed here is a very efficient, robust, and easy-to-implement strategy from an industrial application point of view. (c) 2006 Wiley Periodicals, Inc.

Public Information for Water Pollution Control.

Science.gov (United States)

Water Pollution Control Federation, Washington, DC.

This publication is a handbook for water pollution control personnel to guide them towards a successful public relations program. This handbook was written to incorporate the latest methods of teaching basic public information techniques to the non-professional in this area. Contents include: (1) a rationale for a public information program; (2)…

Latest results from HERA

Indian Academy of Sciences (India)

Standard Model where particles that have quantum numbers of both leptons and quarks are produced. Then a search ..... The limits from HERA can be seen to be very competitive with limits from other colliders especially for low values ... the decay t —bW. A similar decay chain is possible for the production of a single stop in.

Target product profile choices for intra-domiciliary malaria vector control pesticide products: repel or kill?

Directory of Open Access Journals (Sweden)

Moore Sarah J

2011-07-01

Full Text Available Abstract Background The most common pesticide products for controlling malaria-transmitting mosquitoes combine two distinct modes of action: 1 conventional insecticidal activity which kills mosquitoes exposed to the pesticide and 2 deterrence of mosquitoes away from protected humans. While deterrence enhances personal or household protection of long-lasting insecticidal nets and indoor residual sprays, it may also attenuate or even reverse communal protection if it diverts mosquitoes to non-users rather than killing them outright. Methods A process-explicit model of malaria transmission is described which captures the sequential interaction between deterrent and toxic actions of vector control pesticides and accounts for the distinctive impacts of toxic activities which kill mosquitoes before or after they have fed upon the occupant of a covered house or sleeping space. Results Increasing deterrency increases personal protection but consistently reduces communal protection because deterrent sub-lethal exposure inevitably reduces the proportion subsequently exposed to higher lethal doses. If the high coverage targets of the World Health Organization are achieved, purely toxic products with no deterrence are predicted to generally provide superior protection to non-users and even users, especially where vectors feed exclusively on humans and a substantial amount of transmission occurs outdoors. Remarkably, this is even the case if that product confers no personal protection and only kills mosquitoes after they have fed. Conclusions Products with purely mosquito-toxic profiles may, therefore, be preferable for programmes with universal coverage targets, rather than those with equivalent toxicity but which also have higher deterrence. However, if purely mosquito-toxic products confer little personal protection because they do not deter mosquitoes and only kill them after they have fed, then they will require aggressive "catch up" campaigns, with

Gene Disruption Technologies Have the Potential to Transform Stored Product Insect Pest Control.

Science.gov (United States)

Perkin, Lindsey C; Adrianos, Sherry L; Oppert, Brenda

2016-09-19

Stored product insects feed on grains and processed commodities manufactured from grain post-harvest, reducing the nutritional value and contaminating food. Currently, the main defense against stored product insect pests is the pesticide fumigant phosphine. Phosphine is highly toxic to all animals, but is the most effective and economical control method, and thus is used extensively worldwide. However, many insect populations have become resistant to phosphine, in some cases to very high levels. New, environmentally benign and more effective control strategies are needed for stored product pests. RNA interference (RNAi) may overcome pesticide resistance by targeting the expression of genes that contribute to resistance in insects. Most data on RNAi in stored product insects is from the coleopteran genetic model, Tribolium castaneum, since it has a strong RNAi response via injection of double stranded RNA (dsRNA) in any life stage. Additionally, Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR) technology has been suggested as a potential resource for new pest control strategies. In this review we discuss background information on both gene disruption technologies and summarize the advances made in terms of molecular pest management in stored product insects, mainly T. castaneum, as well as complications and future needs.

Optimization and Optimal Control

CERN Document Server

Chinchuluun, Altannar; Enkhbat, Rentsen; Tseveendorj, Ider

2010-01-01

During the last four decades there has been a remarkable development in optimization and optimal control. Due to its wide variety of applications, many scientists and researchers have paid attention to fields of optimization and optimal control. A huge number of new theoretical, algorithmic, and computational results have been observed in the last few years. This book gives the latest advances, and due to the rapid development of these fields, there are no other recent publications on the same topics. Key features: Provides a collection of selected contributions giving a state-of-the-art accou

Particle production in hadron--nucleus collisions above 10 GeV

International Nuclear Information System (INIS)

Busza, W.

1978-01-01

The reasons for interest in the observed phenomena in hadron reactions above 10 GeV are considered. The latest data are not reviewed except for comparison with theoretical models. Among the topics considered are total or absorption cross sections, low average multiplicity, nuclear fragment distributions, implications for the nature of hadrons and their interactions, rapidity distributions, and multiple production energy dependence. 38 references

21 CFR 111.135 - What quality control operations are required for product complaints?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What quality control operations are required for... MANUFACTURING, PACKAGING, LABELING, OR HOLDING OPERATIONS FOR DIETARY SUPPLEMENTS Production and Process Control System: Requirements for Quality Control § 111.135 What quality control operations are required for...

Experience of Google's latest deep learning library, TensorFlow, in a large-scale WLCG cluster

Energy Technology Data Exchange (ETDEWEB)

Kawamura, Gen; Smith, Joshua Wyatt; Quadt, Arnulf [II. Physikalisches Institut, Georg-August-Universitaet Goettingen (Germany)

2016-07-01

The researchers at the Google Brain team released their second generation's Deep Learning library, TensorFlow, as an open-source package under the Apache 2.0 license in November, 2015. Google has already deployed the first generation's library using DistBlief in various systems such as Google Search, advertising systems, speech recognition systems, Google Images, Google Maps, Street View, Google Translate and many other latest products. In addition, many researchers in high energy physics have recently started to understand and use Deep Learning algorithms in their own research and analysis. We conceive a first use-case scenario of TensorFlow to create the Deep Learning models from high-dimensional inputs like physics analysis data in a large-scale WLCG computing cluster. TensorFlow carries out computations using a dataflow model and graph structure onto a wide variety of different hardware platforms and systems, such as many CPU architectures, GPUs and smartphone platforms. Having a single library that can distribute the computations to create a model to the various platforms and systems would significantly simplify the use of Deep Learning algorithms in high energy physics. We deploy TensorFlow with the Docker container environments and present the first use in our grid system.

Assisting People with Multiple Disabilities by Actively Keeping the Head in an Upright Position with a Nintendo Wii Remote Controller through the Control of an Environmental Stimulation

Science.gov (United States)

Shih, Ching-Hsiang; Shih, Chia-Ju; Shih, Ching-Tien

2011-01-01

The latest researches have adopted software technology by applying the Nintendo Wii Remote Controller to the correction of hyperactive limb behavior. This study extended Wii Remote Controller functionality for improper head position (posture) correction (i.e. actively adjusting abnormal head posture) to assess whether two people with multiple…

Review of scientific Research results in identification of plant raw materials in food products

OpenAIRE

GOLUBTSOVA YU. V.

2016-01-01

Currently, the science-based capabilities have been generated to develop and test various identification methods of food products and reveal adulteration using advanced technique and processes. This article reviews researches and developments to identify the plant raw materials in food products based on morphological, anatomic, physical and chemical test methods and the latest DNA-technologies. Review of physical, chemical, anatomic and morphological test methods to identify raw materials bot...

A continuous-time control model on production planning network ...

African Journals Online (AJOL)

A continuous-time control model on production planning network. DEA Omorogbe, MIU Okunsebor. Abstract. In this paper, we give a slightly detailed review of Graves and Hollywood model on constant inventory tactical planning model for a job shop. The limitations of this model are pointed out and a continuous time ...

[Investigation on production process quality control of traditional Chinese medicine--Banlangen granule as an example].

Science.gov (United States)

Tan, Manrong; Yan, Dan; Qiu, Lingling; Chen, Longhu; Yan, Yan; Jin, Cheng; Li, Hanbing; Xiao, Xiaohe

2012-04-01

For the quality management system of herbal medicines, intermediate and finished products it exists the " short board" effect of methodologies. Based on the concept of process control, new strategies and new methods of the production process quality control had been established with the consideration of the actual production of traditional Chinese medicine an the characteristics of Chinese medicine. Taking Banlangen granule as a practice example, which was effective and widespread application, character identification, determination of index components, chemical fingerprint and biometrics technology were sequentially used respectively to assess the quality of Banlangen herbal medicines, intermediate (water extraction and alcohol precipitation) and finished product. With the transfer rate of chemical information and biological potency as indicators, the effectiveness and transmission of the above different assessments and control methods had been researched. And ultimately, the process quality control methods of Banlangen granule, which were based on chemical composition analysis-biometric analysis, had been set up. It can not only validly solute the current status that there were many manufacturers varying quality of Banlangen granule, but also ensure and enhance its clinical efficacy. Furthermore it provided a foundation for the construction of the quality control of traditional Chinese medicine production process.

Latest astronomical constraints on some non-linear parametric dark energy models

Science.gov (United States)

Yang, Weiqiang; Pan, Supriya; Paliathanasis, Andronikos

2018-04-01

We consider non-linear redshift-dependent equation of state parameters as dark energy models in a spatially flat Friedmann-Lemaître-Robertson-Walker universe. To depict the expansion history of the universe in such cosmological scenarios, we take into account the large-scale behaviour of such parametric models and fit them using a set of latest observational data with distinct origin that includes cosmic microwave background radiation, Supernove Type Ia, baryon acoustic oscillations, redshift space distortion, weak gravitational lensing, Hubble parameter measurements from cosmic chronometers, and finally the local Hubble constant from Hubble space telescope. The fitting technique avails the publicly available code Cosmological Monte Carlo (COSMOMC), to extract the cosmological information out of these parametric dark energy models. From our analysis, it follows that those models could describe the late time accelerating phase of the universe, while they are distinguished from the Λ-cosmology.

Latest advances in high brightness disk lasers

Science.gov (United States)

Kuhn, Vincent; Gottwald, Tina; Stolzenburg, Christian; Schad, Sven-Silvius; Killi, Alexander; Ryba, Tracey

2015-02-01

In the last decade diode pumped solid state lasers have become an important tool for many industrial materials processing applications. They combine ease of operation with efficiency, robustness and low cost. This paper will give insight in latest progress in disk laser technology ranging from kW-class CW-Lasers over frequency converted lasers to ultra-short pulsed lasers. The disk laser enables high beam quality at high average power and at high peak power at the same time. The power from a single disk was scaled from 1 kW around the year 2000 up to more than 10 kW nowadays. Recently was demonstrated more than 4 kW of average power from a single disk close to fundamental mode beam quality (M²=1.38). Coupling of multiple disks in a common resonator results in even higher power. As an example we show 20 kW extracted from two disks of a common resonator. The disk also reduces optical nonlinearities making it ideally suited for short and ultrashort pulsed lasers. In a joint project between TRUMPF and IFSW Stuttgart more than 1.3 kW of average power at ps pulse duration and exceptionally good beam quality was recently demonstrated. The extremely low saturated gain makes the disk laser ideal for internal frequency conversion. We show >1 kW average power and >6 kW peak power in multi ms pulsed regime from an internally frequency doubled disk laser emitting at 515 nm (green). Also external frequency conversion can be done efficiently with ns pulses. >500 W of average UV power was demonstrated.

Prevention and Control Strategies to Counter Dengue Virus Infection

Directory of Open Access Journals (Sweden)

Irfan A. Rather

2017-07-01

Full Text Available Dengue is currently the highest and rapidly spreading vector-borne viral disease, which can lead to mortality in its severe form. The globally endemic dengue poses as a public health and economic challenge that has been attempted to suppress though application of various prevention and control techniques. Therefore, broad spectrum techniques, that are efficient, cost-effective, and environmentally sustainable, are proposed and practiced in dengue-endemic regions. The development of vaccines and immunotherapies have introduced a new dimension for effective dengue control and prevention. Thus, the present study focuses on the preventive and control strategies that are currently employed to counter dengue. While traditional control strategies bring temporary sustainability alone, implementation of novel biotechnological interventions, such as sterile insect technique, paratransgenesis, and production of genetically modified vectors, has improved the efficacy of the traditional strategies. Although a large-scale vector control strategy can be limited, innovative vaccine candidates have provided evidence for promising dengue prevention measures. The use of tetravalent dengue vaccine (CYD-TDV has been the most effective so far in treating dengue infections. Nonetheless, challenges and limitation hinder the progress of developing integrated intervention methods and vaccines; while the improvement in the latest techniques and vaccine formulation continues, one can hope for a future without the threat of dengue virus.

Prevention and Control Strategies to Counter Dengue Virus Infection.

Science.gov (United States)

Rather, Irfan A; Parray, Hilal A; Lone, Jameel B; Paek, Woon K; Lim, Jeongheui; Bajpai, Vivek K; Park, Yong-Ha

2017-01-01

Dengue is currently the highest and rapidly spreading vector-borne viral disease, which can lead to mortality in its severe form. The globally endemic dengue poses as a public health and economic challenge that has been attempted to suppress though application of various prevention and control techniques. Therefore, broad spectrum techniques, that are efficient, cost-effective, and environmentally sustainable, are proposed and practiced in dengue-endemic regions. The development of vaccines and immunotherapies have introduced a new dimension for effective dengue control and prevention. Thus, the present study focuses on the preventive and control strategies that are currently employed to counter dengue. While traditional control strategies bring temporary sustainability alone, implementation of novel biotechnological interventions, such as sterile insect technique, paratransgenesis, and production of genetically modified vectors, has improved the efficacy of the traditional strategies. Although a large-scale vector control strategy can be limited, innovative vaccine candidates have provided evidence for promising dengue prevention measures. The use of tetravalent dengue vaccine (CYD-TDV) has been the most effective so far in treating dengue infections. Nonetheless, challenges and limitation hinder the progress of developing integrated intervention methods and vaccines; while the improvement in the latest techniques and vaccine formulation continues, one can hope for a future without the threat of dengue virus.

Quality control in the fuel elements production process

International Nuclear Information System (INIS)

Katanic-Popovic, J.; Spasic, Z.; Djuricis, Lj.

1977-01-01

Recently great attention has been paid at the international level to the analysis of production processes and quality control of fuel and fuel elements with the aim to speed up activity of proposing and accepting standards and measurement methods. IAEA also devoted great interest to these problems appealing to more active participation of all users and producers fuel elements in a general effort to secure successful work of nuclear plants. For adequate and timely participation in future in the establishment and analysis of general requirements and documentation for the control of purchased or self produced fuel elements in out country it is necessary to be well informed and to follow this activity at the international level. (author)

Intelligent control systems 1990

International Nuclear Information System (INIS)

Shoureshi, R.

1991-01-01

The field of artificial intelligence (Al) has generated many useful ideas and techniques that can be integrated into the design of control systems. It is believed and, for special cases, has been demonstrated, that integration of Al into control systems would provide the necessary tools for solving many of the complex problems that present control techniques and Al algorithms are unable to do, individually. However, this integration requires the development of basic understanding and new fundamentals to provide scientific bases for achievement of its potential. This book presents an overview of some of the latest research studies in the area of intelligent control systems. These papers present techniques for formulation of intelligent control, and development of the rule-based control systems. Papers present applications of control systems in nuclear power plants and HVAC systems

Providing floating capabilities in latest-generation sand screens

Energy Technology Data Exchange (ETDEWEB)

Bowen, E.G.; Coronado, M.P. [Society of Petroleum Engineers, Richardson, TX (United States)]|[Baker Hughes, Houston, TX (United States)

2008-10-15

Alternative production methods are needed for the massive reserves located in the bitumen region of Canada's tar sands. The area has over 100 installations of sand screens/slotted liners in both injection and production legs using steam-assisted gravity drainage (SAGD) technology. Multiple wells must be drilled from a single pad because of the sensitive nature of the environment. With significant depths of these wells, a floating sand screen provides assurance that the sand screen will reach the desired depth. Paraffin is generally used to plug the flow access of the screen during installation. This paper discussed a new technology that has been developed to allow for sand screen installations without relying on paraffin wax to withstand differential pressure. The new technology uses a hydro-mechanical valving system incorporated into the screen design to temporarily close off the screen while being run in the hole. The paper described how the technology could provide a reliable, time-saving solution for SAGD installations when floating sand control screens are needed. The paper discussed current technology and its limitations, sand screen installation, screen design for floating applications, and additional applications. It was concluded that this technology solution provides a unique alternative to the methods currently used to install sand screens with SAGD technology in the fast growing Canadian market for bitumen recovery. 2 refs., 5 figs.

Control and Diagnosis in Integrated Product Development - Observations during the Development of an AGV

Science.gov (United States)

Stetter, R.; Simundsson, A.

2015-11-01

This paper is concerned with the integration of control and diagnosis functionalities into the development of complete systems which include mechanical, electrical and electronic subsystems. For the development of such systems the strategies, methods and tools of integrated product development have attracted significant attention during the last decades. Today, it is generally observed that product development processes of complex systems can only be successful if the activities in the different domains are well connected and synchronised and if an ongoing communication is present - an ongoing communication spanning the technical domains and also including functions such as production planning, marketing/distribution, quality assurance, service and project planning. Obviously, numerous approaches to tackle this challenge are present in scientific literature and in industrial practice, as well. Today, the functionality and safety of most products is to a large degree dependent on control and diagnosis functionalities. Still, there is comparatively little research concentrating on the integration of the development of these functionalities into the overall product development processes. The main source of insight of the presented research is the product development process of an Automated Guided Vehicle (AGV) which is intended to be used on rough terrain. The paper starts with a background describing Integrated Product Development. The second section deals with the product development of the sample product. The third part summarizes some insights and formulates first hypotheses concerning control and diagnosis in Integrated Product Development.

Analysis of power and frequency control requirements in view of increased decentralized production and market liberalization

International Nuclear Information System (INIS)

Roffel, B.; Boer, W.W. de

2003-01-01

This paper presents a systematic approach of the analysis of the minimum control requirements that are imposed on power producing units in the Netherlands, especially in the case when decentralized production increases. Also some effects of the liberalization on the control behavior are analyzed. First an overview is given of the amount and type of power production in the Netherlands, followed by a review of the control requirements. Next models are described, including a simplified model for the UCTE power system. The model was tested against frequency and power measurements after failure of a 558 MW production unit in the Netherlands. Agreement between measurements and model predictions proved to be good. The model was subsequently used to analyze the primary and secondary control requirements and the impact of an increase in decentralized power production on the fault restoration capabilities of the power system. Since the latter production units are not actively participating in primary and secondary control, fault restoration takes longer and becomes unacceptable when only 35% of the power producing units participate in secondary control. Finally, the model was used to study the impact of deregulation, especially the effect of 'block scheduling', on additional control actions of the secondary control. (Author)

Natural Products from Mangrove Actinomycetes

Science.gov (United States)

Xu, Dong-Bo; Ye, Wan-Wan; Han, Ying; Deng, Zi-Xin; Hong, Kui

2014-01-01

Mangroves are woody plants located in tropical and subtropical intertidal coastal regions. The mangrove ecosystem is becoming a hot spot for natural product discovery and bioactivity survey. Diverse mangrove actinomycetes as promising and productive sources are worth being explored and uncovered. At the time of writing, we report 73 novel compounds and 49 known compounds isolated from mangrove actinomycetes including alkaloids, benzene derivatives, cyclopentenone derivatives, dilactones, macrolides, 2-pyranones and sesquiterpenes. Attractive structures such as salinosporamides, xiamycins and novel indolocarbazoles are highlighted. Many exciting compounds have been proven as potential new antibiotics, antitumor and antiviral agents, anti-fibrotic agents and antioxidants. Furthermore, some of their biosynthetic pathways have also been revealed. This review is an attempt to consolidate and summarize the past and the latest studies on mangrove actinomycetes natural product discovery and to draw attention to their immense potential as novel and bioactive compounds for marine drugs discovery. PMID:24798926

Multidirectional analysis of technical efficiency for pig production systems

DEFF Research Database (Denmark)

Labajavo, Katarina; Hansson, Helena; Asmild, Mette

2016-01-01

Declining profitability and ongoing structural changes in the pig sector require thorough efficiency analysis of individual production factors. In this study we calculated technical efficiency indices for each input and output using multidirectional efficiency analysis and examined the relationship...... between ‘farm-specific characteristics’ and input and output technical efficiencies by production type (piglet, growing-finishing, finish-to-farrow). The results indicated that advisory services and farm location were not significantly correlated with technical efficiency. Similar results were obtained...... for ‘housing practices’, with the exception of the latest technology such as heated floors in relation to input labour technical efficiency for growing-finishing and finish-to-farrow productions. Use of written instructions for feeding for growing-finishing and finish-to-farrow production and written...

Simulation Results of Closed Loop Controlled Interline Power Flow Controller System

Directory of Open Access Journals (Sweden)

P. USHA RANI

2016-01-01

Full Text Available The Interline Power Flow Controller (IPFC is the latest generation of Flexible AC Transmission Systems (FACTS devices which can be used to control power flows of multiple transmission lines. A dispatch strategy is proposed for an IPFC operating at rated capacity, in which the power circulation between the two series converters is used as the parameter to optimize the voltage profile and power transfer. Voltage stability curves for test system are shown to illustrate the effectiveness of this proposed strategy. In this paper, a circuit model for IPFC is developed and simulation of interline power flow controller is done using the proposed circuit model. Simulation is done using MATLAB simulink and the results are presented.

Model-based control of a ballast-stabilized floating wind turbine exposed to wind and waves

Energy Technology Data Exchange (ETDEWEB)

Christiansen, Soeren

2013-01-15

The wind turbine is a commercial product which is competing against other sources of energy, such as coal and gas. This competition drives a constant development to reduce costs and improve efficiency in order to reduce the total cost of the energy. The latest offshore development is the floating wind turbine, for water depths beyond 50 meters where winds are stronger and less turbulent. A floating wind turbine is subject to not only aerodynamics and wind induced loads, but also to hydrodynamics and wave induced loads. In contrast to a bottom fixed wind turbine, the floating structure, the hydrodynamics and the loads change the dynamic behavior of a floating wind turbine. Consequently, conventional wind turbine control cause instabilities on floating wind turbines. This work addresses the control of a floating spar buoy wind turbine, and focuses on the impact of the additional platform dynamics. A time varying control model is presented based on the wind speed and wave frequency. Estimates of the wind speed and wave frequency are used as scheduling variables in a gain scheduled linear quadratic controller to improve the electrical power production while reducing fatigue. To address the problem of negative damped fore-aft tower motion, additional control loops are suggested which stabilize the response of the onshore controller and reduce the impact of the wave induced loads. This research is then extended to model predictive control, to further address wave disturbances. In the context of control engineering, the dynamics and disturbances of a floating wind turbine have been identified and modeled. The objectives of maximizing the production of electrical power and minimizing fatigue have been reached by using advanced methods of estimation and control. (Author)

Control of polysilicon on-film particulates with on-product measurements

Science.gov (United States)

Barker, Judith B.; Chain, Elizabeth E.; Plachecki, Vincent E.

1997-08-01

Historically, a number of in-line particle measurements have been performed on separate test wafers included with product wafers during polysilicon processes. By performing film thickness and particulate measurements directly on product wafers, instead, a number of benefits accrue: (1) reduced test wafer usage, (2) reduced test wafer storage requirements, (3) reduced need for equipment to reclaim test wafers, (4) reduced need for direct labor to reclaim test wafers, and (5) reduced engineering 'false alarms' due to incorrectly processed test wafers. Implementation of on-product measurements for the polysilicon diffusion process required a number of changes in both philosophy and methodology. We show the necessary steps to implementation of on-product particle measurements with concern for overall manufacturing efficiency and the need to maintain appropriate control. Particle results from the Tencor 7600 Surfscan are presented.

Chooz B1 start-up marked by total computer control

International Nuclear Information System (INIS)

Anon.

1995-01-01

The start-up of Chooz B1, the first of EdF's latest generation 1450 MWe N4 reactors, marks the first use in a nuclear power plant of a fully computerised control room. Working in partnership with EdF, Sema Group designed and supplied the advanced command and control system for this plant. (Author)

Design controls for the medical device industry

CERN Document Server

Teixeira, Marie B

2013-01-01

The second edition of a bestseller, Design Controls for the Medical Device Industry provides a comprehensive review of the latest design control requirements, as well as proven tools and techniques to ensure your company's design control program evolves in accordance with current industry practice. The text assists in the development of an effective design control program that not only satisfies the US FDA Quality System Regulation (QSR) and ISO 9001 and 13485 standards, but also meets today's third-party auditor/investigator expectations and saves you valuable time and money.The author's cont

Communication and control for networked complex systems

CERN Document Server

Peng, Chen; Han, Qing-Long

2015-01-01

This book reports on the latest advances in the study of Networked Control Systems (NCSs). It highlights novel research concepts on NCSs; the analysis and synthesis of NCSs with special attention to their networked character; self- and event-triggered communication schemes for conserving limited network resources; and communication and control co-design for improving the efficiency of NCSs. The book will be of interest to university researchers, control and network engineers, and graduate students in the control engineering, communication and network sciences interested in learning the core principles, methods, algorithms and applications of NCSs.

Ethylene Control Technologies in Extending Postharvest Shelf Life of Climacteric Fruit.

Science.gov (United States)

Zhang, Junhua; Cheng, Dong; Wang, Baobin; Khan, Iqbal; Ni, Yonghao

2017-08-30

Fresh fruit is important for a healthy diet. However, because of their seasonal production, regional specific cultivation, and perishable nature, it is essential to develop preservation technologies to extend the postharvest shelf life of fresh fruits. Climacteric fruit adopt spoilage because of ethylene, a key hormone associated with the ripening process. Therefore, controlling ethylene activity by following safe and effective approaches is a key to extend the postharvest shelf life of fruit. In this review, ethylene control technologies will be discussed aiming for the need of developing more innovative and effective approaches. The biosynthesis pathway will be given first. Then, the technologies determining the postharvest shelf life of climacteric fruit will be described with special attention to the latest and significant published works in this field. Special attention is given to 1-methylcyclopropene (1-MCP), which is effective in fruit preservation technologies. Finally, the encapsulation technology to improve the stability of 1-MCP will be proposed, using a potential encapsulation agent of 1-MCP, calixarene.

Stratigraphic response across a structurally dynamic shelf: The latest guadalupian composite sequence at Walnut Canyon, New Mexico, U.S.A

Science.gov (United States)

Rush, J.; Kerans, C.

2010-01-01

The uppermost Yates and Tansill formations (Late Permian), as exposed along Walnut Canyon in Carlsbad Caverns National Park, New Mexico, USA, provide a unique opportunity to document the depositional architecture of a progradational, oversteepened, and mechanically failure-prone carbonate platform. Detailed facies mapping permitted critical assessment of depositional processes operating along this structurally dynamic platform margin. At the shelf crest, thick (12 m), vertically stacked fenestral-pisolite-tepee complexes indicate a stable shoreline. Early lithification of sediments and extensive cementation fostered rapid vertical accretion and allowed the shelf crest to easily adjust to base-level oscillations by stepping landward, stepping seaward, or aggrading. This production imbalance-in combination with syndepositional brittle failure and down-to-the-basin tilting(architecture, fracture properties, and a highly refined fusulinid biostratigraphic framework. Where fractures tip out, down-to-the-basin rotation is often observed with concurrent seaward thickening of overlying beds, indicating that such fractures functioned as a syndepositional hinge. A facies disjunction and horizontally juxtaposed fusulinid zonation were documented across an 80?? seaward-dipping dilational fracture filled with polymict breccia. An overlying damage zone consisting of spar-cemented fractures nested within silt-filled fractures illustrates periodic reactivation. Field relationships indicate that the dilational fracture approximates a paleoescarpment that resulted from catastrophic failure of the Capitan platform margin. Younger strata onlapped the paleoescarpment and gradually filled the reentrant. This mechanically compromised paleoescarpment was subsequently reactivated during the latest Guadalupian lowstand and was subaerially filled by siliciclastics and polymict breccia derived from the platform top. Results from Walnut Canyon indicate that shelf crest aggradation dominantly

Tire Production and Pollution Control. Environmental Education Curriculum. Revised.

Science.gov (United States)

Topeka Public Schools, KS.

This unit was developed to introduce secondary students to the many facets of a typical, large manufacturing plant - the Topeka Goodyear Tire and Rubber Company - in an effort to increase awareness of sound environmental practices in industry. Its five major foci include the production of tires and quality control procedures; applications of…

Latest Results on Top Quark Properties: \\\\ Deciphering the DNA of the heaviest quark

CERN Document Server

Gallinaro, Michele

2017-01-01

The top quark, the heaviest known elementary particle discovered at the Fermilab Tevatron more than twenty years ago, has taken a central role in the study of fundamental interactions. Due to its large mass, the top quark provides a unique environment for tests of the standard model. With a cumulative luminosity of more than 100~fb$^{-1}$ collected at $\\sqrt{s}=7,8,13$~TeV by each of the ATLAS and CMS experiments at the Large Hadron Collider in the first ten years of operation, top quark physics is probing uncharted territories in precision and rare measurements with sensitivity to New Physics processes. This document summarizes the latest experimental measurements and studies of top quark properties.

Optimal control of hydrogen production in a continuous anaerobic fermentation bioreactor

Energy Technology Data Exchange (ETDEWEB)

Aceves-Lara, Cesar-Arturo [INRA, UMR792, Ingenierie des Systemes Biologiques et des Procedes, Toulouse (France); CNRS, UMR5504, Toulouse, France 135 Avenue de Rangueil, Toulouse Cedex F-31077 (France); INRA, UR050, Laboratoire de Biotechnologie de l' Environnement, Avenue des Etangs, Narbonne F-11100 (France); Latrille, Eric; Steyer, Jean-Philippe [INRA, UR050, Laboratoire de Biotechnologie de l' Environnement, Avenue des Etangs, Narbonne F-11100 (France)

2010-10-15

This paper addresses the problem of optimization of hydrogen production in continuous anaerobic digesters using a model predictive control (MPC) strategy. The process is described by a dynamic nonlinear model. The influent concentration of molasses together with the effluent substrate and product concentrations of acetate, propionate, butyrate and biomass were estimated by an asymptotic online observer from measurements of gas composition in H{sub 2} and CO{sub 2} and gas flow rate. The observer was tested experimentally before to apply MPC online. The combined strategy (MPC and observer) was used in order to optimize a bioreactor of 2 L. The hydrogen production was increased by 75% up to 8.27mL{sub H{sub 2}} L{sup -1}min{sup -1}, using the influent flow rate as the main control variable while keeping the conversion of the influent concentration higher than 95% and maintaining the temperature at 37 C and pH at 5.5. (author)

Mathematical modelling of the process of quality control of construction products

Directory of Open Access Journals (Sweden)

Pogorelov Vadim

2017-01-01

Full Text Available The study presents the results of years of research in the field of quality management of industrial production construction production, based on mathematical modelling techniques, process and results of implementing the developed programme of monitoring and quality control in the production process of the enterprise. The aim of this work is the presentation of scientific community of the practical results of mathematical modelling in application programs. In the course of the research addressed the description of the applied mathematical models, views, practical results of its application in the applied field to assess quality control. The authors used this mathematical model in practice. The article presents the results of applying this model. The authors developed the experimental software management and quality assessment by using mathematical modeling methods. The authors continue research in this direction to improve the diagnostic systems and quality management systems based on mathematical modeling methods prognostic and diagnostic processes.

ASSESSMENT OF A WIND TURBINE INTELLIGENT CONTROLLER FOR ENHANCED ENERGY PRODUCTION AND POLLUTION REDUCTION

Science.gov (United States)

This study assessed the enhanced energy production which is possible when variable-speed wind turbines are electronically controlled by an intelligent controller for efficiency optimization and performance improvement. The control system consists of three fuzzy- logic controllers...

Measurement of the jet production properties at the LHC with the ATLAS Detector

CERN Document Server

Tokar, Stanislav; The ATLAS collaboration

2015-01-01

Latest results on the jet production properties obtained by the ATLAS experiment are presented. Jet physics events produced in pp collisions at 7 TeV have been studied. The dijet double differential cross sections as a function of dijet invariant mass for different rapidity regions are reported. Dijet flavour decomposition, a lower limit on the quark compositeness scale, inclusive jet production differential cross sections, three-jet differential production cross sections as well as a measurement of jet shapes for b-jets and light jets from top quark pair events are also reported.

Latest oil data, trends and prospects

International Nuclear Information System (INIS)

Tempest, Paul

1996-01-01

Reserves of crude oil, especially in non-opec areas continue to grow steadily. OPEC, however, remains dominant in the international trade of oil. Oil production, too, is buoyant, with expansion in OPEC running at 0.7% for 1994 and non-OPEC production expansion at 4.2%. Overall demand for oil also rose (by 1.7%), a sharp fall in CIS state consumption notwithstanding. Import dependence continues to grow. Heavy investment by the petroleum industry in production, transportation and processing is expected over the next thirty years. However, oil's share of the world energy mix continues to be eroded by nuclear power, gas and coal, despite adequate supplies. (UK)

Statistical process control: An approach to quality assurance in the production of vitrified nuclear waste

International Nuclear Information System (INIS)

Pulsipher, B.A.; Kuhn, W.L.

1987-01-01

Current planning for liquid high-level nuclear wastes existing in the United States includes processing in a liquid-fed ceramic melter to incorporate it into a high-quality glass, and placement in a deep geologic repository. The nuclear waste vitrification process requires assurance of a quality product with little or no final inspection. Statistical process control (SPC) is a quantitative approach to one quality assurance aspect of vitrified nuclear waste. This method for monitoring and controlling a process in the presence of uncertainties provides a statistical basis for decisions concerning product quality improvement. Statistical process control is shown to be a feasible and beneficial tool to help the waste glass producers demonstrate that the vitrification process can be controlled sufficiently to produce an acceptable product. This quantitative aspect of quality assurance could be an effective means of establishing confidence in the claims to a quality product

Statistical process control: An approach to quality assurance in the production of vitrified nuclear waste

International Nuclear Information System (INIS)

Pulsipher, B.A.; Kuhn, W.L.

1987-02-01

Current planning for liquid high-level nuclear wastes existing in the US includes processing in a liquid-fed ceramic melter to incorporate it into a high-quality glass, and placement in a deep geologic repository. The nuclear waste vitrification process requires assurance of a quality product with little or no final inspection. Statistical process control (SPC) is a quantitative approach to one quality assurance aspect of vitrified nuclear waste. This method for monitoring and controlling a process in the presence of uncertainties provides a statistical basis for decisions concerning product quality improvement. Statistical process control is shown to be a feasible and beneficial tool to help the waste glass producers demonstrate that the vitrification process can be controlled sufficiently to produce an acceptable product. This quantitative aspect of quality assurance could be an effective means of establishing confidence in the claims to a quality product. 2 refs., 4 figs

Demonstrating multi-layered MAS in control of offshore oil and gas production

DEFF Research Database (Denmark)

Lindegaard Mikkelsen, Lars; Næumann, J. R.; Demazeau, Y.

2013-01-01

From a control perspective, offshore oil and gas production is very challenging due to the many and potentially conflicting production objectives that arise from the intrinsic complexity of the oil and gas domain. In this paper, we demonstrate how a multi-layered multi-agent system can be used in...

Gene Disruption Technologies Have the Potential to Transform Stored Product Insect Pest Control

Directory of Open Access Journals (Sweden)

Lindsey C. Perkin

2016-09-01

Full Text Available Stored product insects feed on grains and processed commodities manufactured from grain post-harvest, reducing the nutritional value and contaminating food. Currently, the main defense against stored product insect pests is the pesticide fumigant phosphine. Phosphine is highly toxic to all animals, but is the most effective and economical control method, and thus is used extensively worldwide. However, many insect populations have become resistant to phosphine, in some cases to very high levels. New, environmentally benign and more effective control strategies are needed for stored product pests. RNA interference (RNAi may overcome pesticide resistance by targeting the expression of genes that contribute to resistance in insects. Most data on RNAi in stored product insects is from the coleopteran genetic model, Tribolium castaneum, since it has a strong RNAi response via injection of double stranded RNA (dsRNA in any life stage. Additionally, Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR technology has been suggested as a potential resource for new pest control strategies. In this review we discuss background information on both gene disruption technologies and summarize the advances made in terms of molecular pest management in stored product insects, mainly T. castaneum, as well as complications and future needs.

Latest developments for a computer aided thermohydraulic network

International Nuclear Information System (INIS)

Alemberti, A.; Graziosi, G.; Mini, G.; Susco, M.

1999-01-01

Thermohydraulic networks are I-D systems characterized by a small number of basic components (pumps, valves, heat exchangers, etc) connected by pipes and limited spatially by a defined number of boundary conditions (tanks, atmosphere, etc). The network system is simulated by the well known computer program RELAPS/mod3. Information concerning the network geometry component behaviour, initial and boundary conditions are usually supplied to the RELAPS code using an ASCII input file by means of 'input cards'. CATNET (Computer Aided Thermalhydraulic NETwork) is a graphically user interface that, under specific user guidelines which completely define its range of applicability, permits a very high level of standardization and simplification of the RELAPS/mod3 input deck development process as well as of the output processing. The characteristics of the components (pipes, valves, pumps etc), defining the network system can be entered through CATNET. The CATNET interface is provided by special functions to compute form losses in the most typical bending and branching configurations. When the input of all system components is ready, CATNET is able to generate the RELAPS/mod3 input file. Finally, by means of CATNET, the RELAPS/mod3 code can be run and its output results can be transformed to an intuitive display form. The paper presents an example of application of the CATNET interface as well as the latest developments which greatly simplified the work of the users and allowed to reduce the possibility of input errors. (authors)

Current knowledge from experimental works with radioprotective drugs from the viewpoint of latest scientific research

International Nuclear Information System (INIS)

Skalka, J.

2008-01-01

The protection of both human and animal population against a radiation impairment proves to be an impulse for continuous intensive searching for plants with radioprotective properties, identification of their radioprotective components and examination of their effects both in vivo an in vitro. I am presenting the results as well as knowledge of a latest scientific research in this field with testing the following plants: Vigna radiata, Mentha piperita, Citrus aurantium var. amara, Syzygium cumini, Tinospora cordifolia, Aegle marmelos, Phyllanthus amarus, Aloe vera, Angelica sinensis, Rosemarinus officinalis, Panax ginseng, Hippophae rhamnoides, Ocimum sanctum, Crataegus microphylla. (authors)

NFL Films music scoring stage and control room space

Science.gov (United States)

Berger, Russ; Schrag, Richard C.; Ridings, Jason J.

2003-04-01

NFL Films' new 200,000 sq. ft. corporate headquarters is home to an orchestral scoring stage used to record custom music scores to support and enhance their video productions. Part of the 90,000 sq. ft. of sound critical technical space, the music scoring stage and its associated control room are at the heart of the audio facilities. Driving the design were the owner's mandate for natural light, wood textures, and an acoustical environment that would support small rhythm sections, soloists, and a full orchestra. Being an industry leader in cutting-edge video and audio formats, the NFLF required that the technical spaces allow the latest in technology to be continually integrated into the infrastructure. Never was it more important for a project to hold true to the adage of ``designing from the inside out.'' Each audio and video space within the facility had to stand on its own with regard to user functionality, acoustical accuracy, sound isolation, noise control, and monitor presentation. A detailed look at the architectural and acoustical design challenges encountered and the solutions developed for the performance studio and the associated control room space will be discussed.

Phase distribution of ecologically controlled chemical elements in production of extraction phosphoric acid

International Nuclear Information System (INIS)

Kazak, V.G.; Agnelov, A.I.; Zajtsev, P.M.

1995-01-01

Content of 16 ecologically controlled chemical element (among them Cd, Sr, Th, U, V, Y) in solid and liquid phases of extraction phosphorus acid (EPA) production is determined. These elements are recommended to control by Scientific research institute of human ecology and environment to establish their extraction coefficients to phosphogypsum and EPA and optimal variant of production of ecologically sate phosphorus fertilizers. X-ray fluorescent, atomic-absorption and polarographic methods are used for analysis these elements

CONTROL OF MICROBIAL CONTAMINANTS AND DISINFECTION BY-PRODUCTS (DBPS): COST AND PERFORMANCE

Science.gov (United States)

The USEPA is in the process of developing a sophisticated regulatory strategy in an attempt to balance the complex trade-offs in risks associated with controlling disinfectants and disinfection by-products (D/DBPs) in drinking water. EPA first attempted to control DBPs in 1974, w...

Pilot project to set up a control programme on fishery products

Directory of Open Access Journals (Sweden)

Guia Benedetta Richelmi

2013-06-01

Full Text Available Authentication of fish as fresh or frozenthawed is compulsory because of the widespread fraudulent practice of retailing fish products as fresh, when they have actually been frozen. Moreover, according to EC Regulations 853/2004 and 1276/2011, fish intended for raw consumption has to be deepfrozen before usage, to protect consumers against Anisakiasis. In this study, a food business operator set an example of good quality control by collaborating with health authorities and an official laboratory in charge of food control, to evaluate the feasibility of a further integrated regional plan on fish safety. Furthermore, differences in microscopic patterns related to freezing time complying (24 h and not complying (12 h with legislation in force were evaluated. Ten samples obtained from red and white-meat fish, and based on real production of the food business, were identified to evaluate the histological method performance in correctly classifying fish as fresh/frozen as well as the microbiological and chemical safety issues possibly related to fishery products. For two samples, species identification was needed. Based on the histological method, one out of ten fish was not fresh, though the supplier claimed all fish to be fresh; the others, after freezing, could be characterised microscopically as frozen and a borderline P-value was found between different freezing times. Microbiological parameters and species identification resulted compliant, while flesh from a tuna fish (Euthynnus alletteratus contained mercury residues three times higher than the legally permitted level. Our results highlight the reliability of an integrated approach to control fishery products frauds.

Latest results of SEE measurements obtained by the STRURED demonstrator ASIC

Energy Technology Data Exchange (ETDEWEB)

Candelori, A. [INFN, Section of Padova, Via Marzolo 8, c.a.p. 35131, Padova (Italy); De Robertis, G. [INFN Section of Bari, Via Orabona 4, c.a.p. 70126, Bari (Italy); Gabrielli, A. [Physics Department, University of Bologna, Viale Berti Pichat 6/2, c.a.p. 40127, Bologna (Italy); Mattiazzo, S.; Pantano, D. [INFN, Section of Padova, Via Marzolo 8, c.a.p. 35131, Padova (Italy); Ranieri, A., E-mail: antonio.ranieri@ba.infn.i [INFN Section of Bari, Via Orabona 4, c.a.p. 70126, Bari (Italy); Tessaro, M. [INFN, Section of Padova, Via Marzolo 8, c.a.p. 35131, Padova (Italy)

2011-01-21

With the perspective to develop a radiation-tolerant circuit for High Energy Physics (HEP) applications, a test digital ASIC VLSI chip, called STRURED, has been designed and fabricated using a standard-cell library of commercial 130 nm CMOS technology by implementing three different radiation-tolerant architectures (Hamming, Triple Modular Redundancy and Triple Time Redundancy) in order to correct circuit malfunctions induced by the occurrence of Soft Errors (SEs). SEs are one of the main reasons of failures affecting electronic digital circuits operating in harsh radiation environments, such as in experiments performed at HEP colliders or in apparatus to be operated in space. In this paper we present and discuss the latest results of SE cross-section measurements performed using the STRURED digital device, exposed to high energy heavy ions at the SIRAD irradiation facility of the INFN National Laboratories of Legnaro (Padova, Italy). In particular the different behaviors of the input part and the core of the three radiation-tolerant architectures are analyzed in detail.

A Remote Controlled Robotic Arm That Reads Barcodes and Handles Products

Directory of Open Access Journals (Sweden)

Zhi-Ying Chen

2018-03-01

Full Text Available In this study, a 6-axis robotic arm, which was controlled by an embedded Raspberry Pi with onboard WiFi, was developed and fabricated. A mobile application (APP, designed for the purpose, was used to operate and monitor a robotic arm by means of a WiFi connection. A computer vision was used to read common one-dimensional barcode (EAN code for the handling and identification of products such as milk tea drinks, sodas and biscuits. The gripper on the end of the arm could sense the clamping force and allowed real-time control of the amount of force used to hold and handle the products. The packages were all made of different material and this control allowed them to be handled without danger of damage or deformation. The maximum handling torque used was ~1.08 Nm and the mechanical design allowed the force of the gripper to be uniformly applied to the sensor to ensure accurate measurement of the force.

A temperature-controlled photoelectrochemical cell for quantitative product analysis

Science.gov (United States)

Corson, Elizabeth R.; Creel, Erin B.; Kim, Youngsang; Urban, Jeffrey J.; Kostecki, Robert; McCloskey, Bryan D.

2018-05-01

In this study, we describe the design and operation of a temperature-controlled photoelectrochemical cell for analysis of gaseous and liquid products formed at an illuminated working electrode. This cell is specifically designed to quantitatively analyze photoelectrochemical processes that yield multiple gas and liquid products at low current densities and exhibit limiting reactant concentrations that prevent these processes from being studied in traditional single chamber electrolytic cells. The geometry of the cell presented in this paper enables front-illumination of the photoelectrode and maximizes the electrode surface area to electrolyte volume ratio to increase liquid product concentration and hence enhances ex situ spectroscopic sensitivity toward them. Gas is bubbled through the electrolyte in the working electrode chamber during operation to maintain a saturated reactant concentration and to continuously mix the electrolyte. Gaseous products are detected by an in-line gas chromatograph, and liquid products are analyzed ex situ by nuclear magnetic resonance. Cell performance was validated by examining carbon dioxide reduction on a silver foil electrode, showing comparable results both to those reported in the literature and identical experiments performed in a standard parallel-electrode electrochemical cell. To demonstrate a photoelectrochemical application of the cell, CO2 reduction experiments were carried out on a plasmonic nanostructured silver photocathode and showed different product distributions under dark and illuminated conditions.

Multivariable model predictive control design of reactive distillation column for Dimethyl Ether production

Science.gov (United States)

Wahid, A.; Putra, I. G. E. P.

2018-03-01

Dimethyl ether (DME) as an alternative clean energy has attracted a growing attention in the recent years. DME production via reactive distillation has potential for capital cost and energy requirement savings. However, combination of reaction and distillation on a single column makes reactive distillation process a very complex multivariable system with high non-linearity of process and strong interaction between process variables. This study investigates a multivariable model predictive control (MPC) based on two-point temperature control strategy for the DME reactive distillation column to maintain the purities of both product streams. The process model is estimated by a first order plus dead time model. The DME and water purity is maintained by controlling a stage temperature in rectifying and stripping section, respectively. The result shows that the model predictive controller performed faster responses compared to conventional PI controller that are showed by the smaller ISE values. In addition, the MPC controller is able to handle the loop interactions well.

Biomass production efficiency controlled by management in temperate and boreal ecosystems

Science.gov (United States)

Campioli, M.; Vicca, S.; Luyssaert, S.; Bilcke, J.; Ceschia, E.; Chapin, F. S., III; Ciais, P.; Fernández-Martínez, M.; Malhi, Y.; Obersteiner, M.; Olefeldt, D.; Papale, D.; Piao, S. L.; Peñuelas, J.; Sullivan, P. F.; Wang, X.; Zenone, T.; Janssens, I. A.

2015-11-01

Plants acquire carbon through photosynthesis to sustain biomass production, autotrophic respiration and production of non-structural compounds for multiple purposes. The fraction of photosynthetic production used for biomass production, the biomass production efficiency, is a key determinant of the conversion of solar energy to biomass. In forest ecosystems, biomass production efficiency was suggested to be related to site fertility. Here we present a database of biomass production efficiency from 131 sites compiled from individual studies using harvest, biometric, eddy covariance, or process-based model estimates of production. The database is global, but dominated by data from Europe and North America. We show that instead of site fertility, ecosystem management is the key factor that controls biomass production efficiency in terrestrial ecosystems. In addition, in natural forests, grasslands, tundra, boreal peatlands and marshes, biomass production efficiency is independent of vegetation, environmental and climatic drivers. This similarity of biomass production efficiency across natural ecosystem types suggests that the ratio of biomass production to gross primary productivity is constant across natural ecosystems. We suggest that plant adaptation results in similar growth efficiency in high- and low-fertility natural systems, but that nutrient influxes under managed conditions favour a shift to carbon investment from the belowground flux of non-structural compounds to aboveground biomass.

Control and distribution of electrical energy as mirrored by the relevant VDE regulations

Energy Technology Data Exchange (ETDEWEB)

Becker, E [Metzenauer und Jung G.m.b.H., Wuppertal (Germany, F.R.)

1977-01-01

The essay deals with the regulations issued by the VDE in the fields of electrical energy distribution and control on national and international level. Starting from an interesting historical survey the author deals with VDE stipulations, introduces new control systems and explains the latest switching units.

Co-production of acetone and ethanol with molar ratio control enables production of improved gasoline or jet fuel blends.

Science.gov (United States)

Baer, Zachary C; Bormann, Sebastian; Sreekumar, Sanil; Grippo, Adam; Toste, F Dean; Blanch, Harvey W; Clark, Douglas S

2016-10-01

The fermentation of simple sugars to ethanol has been the most successful biofuel process to displace fossil fuel consumption worldwide thus far. However, the physical properties of ethanol and automotive components limit its application in most cases to 10-15 vol% blends with conventional gasoline. Fermentative co-production of ethanol and acetone coupled with a catalytic alkylation reaction could enable the production of gasoline blendstocks enriched in higher-chain oxygenates. Here we demonstrate a synthetic pathway for the production of acetone through the mevalonate precursor hydroxymethylglutaryl-CoA. Expression of this pathway in various strains of Escherichia coli resulted in the co-production of acetone and ethanol. Metabolic engineering and control of the environmental conditions for microbial growth resulted in controllable acetone and ethanol production with ethanol:acetone molar ratios ranging from 0.7:1 to 10.0:1. Specifically, use of gluconic acid as a substrate increased production of acetone and balanced the redox state of the system, predictively reducing the molar ethanol:acetone ratio. Increases in ethanol production and the molar ethanol:acetone ratio were achieved by co-expression of the aldehyde/alcohol dehydrogenase (AdhE) from E. coli MG1655 and by co-expression of pyruvate decarboxylase (Pdc) and alcohol dehydrogenase (AdhB) from Z. mobilis. Controlling the fermentation aeration rate and pH in a bioreactor raised the acetone titer to 5.1 g L(-1) , similar to that obtained with wild-type Clostridium acetobutylicum. Optimizing the metabolic pathway, the selection of host strain, and the physiological conditions employed for host growth together improved acetone titers over 35-fold (0.14-5.1 g/L). Finally, chemical catalysis was used to upgrade the co-produced ethanol and acetone at both low and high molar ratios to higher-chain oxygenates for gasoline and jet fuel applications. Biotechnol. Bioeng. 2016;113: 2079-2087. © 2016 Wiley

BIOMASS PRODUCTION AND FORMULATION OF Bacillus subtilis FOR BIOLOGICAL CONTROL

Directory of Open Access Journals (Sweden)

Amran Muis

2016-10-01

Full Text Available Bacillus subtilis is a widespread bacterium found in soil, water, and air. It controls the growth of certain harmful bacteria and fungi, presumably by competing for nutrients, growth sites on plants, and by directly colonizing and attaching to fungal pathogens. When applied to seeds, it colonizes the developing root system of the plants and continues to live on the root system and provides protection throughout the growing season. The study on biomass production and formulation of B. subtilis for biological control was conducted in the laboratory of Department of Plant Pathology, College of Agriculture, University of the Philippines Los Baños (UPLB-CA, College, Laguna from May to July 2005. The objective of the study was to determine the optimum pH and a good carbon source for biomass production of B. subtilis and to develop a seed treatment formulation of B. subtilis as biological control agent. Results showed that the optimum pH for growth of B. subtilis was pH 6 (1.85 x 109 cfu/ml. In laboratory tests for biomass production using cassava flour, corn flour, rice flour, and brown sugar as carbon sources, it grew best in brown sugar plus yeast extract medium (6.8 x 108 cfu ml-1 in sterile distilled water and 7.8 x 108 cfu ml-1 in coconut water. In test for bacterial biomass carriers, talc proved to be the best in terms of number of bacteria recovered from the seeds (3.98 x 105 cfu seed-1.

Latest Pleistocene and Holocene surficial deposits and landforms of Yosemite Valley, California

Science.gov (United States)

Haddon, E. K.; Stock, G. M.; Booth, D. B.

2016-12-01

Field studies on the surficial geology and geomorphology of Yosemite Valley since the 1870's formed an early basis for our understanding of Quaternary landscape evolution in the central Sierra Nevada. These landmark studies described the erosional origin of Yosemite's iconic scenery, but left details of the latest Pleistocene and Holocene sedimentary record for later investigation. We combined mapping of deposits and landforms with geochronology to reconstruct the geomorphic evolution of Yosemite Valley since the 15 ka retreat of the Last Glacial Maximum (LGM) valley glacier. We document a sustained period of relative landscape stability, characterized by valley-bottom aggradation of glacial till, fluvial sediments, and lacustrine silts, as well as valley-margin accumulation of talus and fan alluvium. Recessional moraines, episodically emplaced rock avalanches, and alluvial fans impeded surface flow and controlled the local base level. This predominantly aggradational regime then shifted to incision in the earliest Holocene, likely due to a diminishing supply of glacial sediment, and created a flight of fluvial terraces inset by up to 9 m. The volume of fringing talus and fan alluvium in comparison with fluvial terrace sequences emphasizes the importance of valley-wall erosion as a sediment source. Cosmogenic 10Be exposure ages from rock avalanche boulders and 14C charcoal ages from deltaic sequences and inset fluvial gravels suggest variable rates of Holocene river incision. Although some incision events likely record local base level changes at the El Capitan LGM recessional moraine, the presence of perched, well-developed outwash terraces downstream indicates a more regional climatic forcing. These findings, including the depositional record of land-use disturbances over the past two centuries, help illuminate the geologic evolution of this celebrated landscape and inform ongoing river-restoration work.

Inventory management and control at the central distribution center for Univar Products International B.V.

NARCIS (Netherlands)

Pholnukulkit, Pimara

2008-01-01

This report presents the outcome of the Logistics Design Project carried out for Univar Products International B.V. The goal of this project is to design an inventory control system and implement an inventory control tool that supports decisions in managing inventory of all products in the central

Latest Trends in the Monitoring of Ships’s Hull Underwater Part and Analysis of Its Effectiveness

OpenAIRE

Urbahs, A; Carjova, K; Vulans, P; Straume, R

2012-01-01

Ship operation is not possible without regular maintenance, inspection and certification, established by international and domestic law, where one of the main goals is an effective operation of a ship. To achieve this, it is important to reduce time and costs involved in carrying out the surveys. This paper explores the law under which it’s required for ship to have inspection of underwater part; identifies problems of ship’s hull underwater part; analyze latest trends in ship's hull underwat...

Raman spectroscopy in quality control of Chinese herbal medicine

Directory of Open Access Journals (Sweden)

Dan-Dan Chen

2017-05-01

Conclusion: An updated systematic review of the published literature has been conducted to analyze the most important milestones and latest achievements in this topic. Raman spectroscopy is playing an increasingly important role in the quality control of CHM and effectively promotes the modernization of CHM.

Bulk H analysis using neutrons for routine quality control of cassava and products

International Nuclear Information System (INIS)

Jonah, S.A.; Okunade, I.O.; Abolude, O.; Onyike, E.; Inuwa, I.M.

2011-01-01

Nuclear and related techniques are useful in addressing the issues of food security and safety facing the world today, via quality control of raw materials and products. In this work, experimental investigations were performed to assess the use of total hydrogen content in cassava and products as a quality control indicator of starch and cyanide contents. The work was carried out using a neutron reflection facility at the Centre for Energy Research and Training, Ahmadu Bello University, Zaria, Nigeria. Cassava samples and products were obtained from retail outlets of Ibadan, Umudike and Zaria, representing three major regions of Nigeria. In general, data obtained indicate a total hydrogen content range of 4.47±0.11-10.71±0.27 wt% for the various samples, including raw, dry and processed cassava. Results show that samples having low hydrogen content are generally rich in cyanide compounds and demonstrate an inverse relationship between hydrogen content and cyanide content. The implication of this is that the neutron reflection facility can be used as a quality control setup for routine determination of hydrogen as an indicator of the cyanide content in cassava and products.

Natural Products from Mangrove Actinomycetes

Directory of Open Access Journals (Sweden)

Dong-Bo Xu

2014-05-01

Full Text Available Mangroves are woody plants located in tropical and subtropical intertidal coastal regions. The mangrove ecosystem is becoming a hot spot for natural product discovery and bioactivity survey. Diverse mangrove actinomycetes as promising and productive sources are worth being explored and uncovered. At the time of writing, we report 73 novel compounds and 49 known compounds isolated from mangrove actinomycetes including alkaloids, benzene derivatives, cyclopentenone derivatives, dilactones, macrolides, 2-pyranones and sesquiterpenes. Attractive structures such as salinosporamides, xiamycins and novel indolocarbazoles are highlighted. Many exciting compounds have been proven as potential new antibiotics, antitumor and antiviral agents, anti-fibrotic agents and antioxidants. Furthermore, some of their biosynthetic pathways have also been revealed. This review is an attempt to consolidate and summarize the past and the latest studies on mangrove actinomycetes natural product discovery and to draw attention to their immense potential as novel and bioactive compounds for marine drugs discovery.

Study of Noise Effects on Rabbit's Hearing Status Using Distortion Product Otoacoustic Emissions

Directory of Open Access Journals (Sweden)

Mojdeh Salehnia

2011-09-01

Full Text Available Background and Aim: Noise-induced hearing loss is the most common problem in industrial areas. This study aimed to determine effects of excessive noise exposure on measurable characteristics of distortion product otoacoustic emissions (DPOAEs in rabbits.Methods: The study was carried out on 12 adult male New Zealand White rabbits including case group - exposed to 500-8000 Hz broadband white noise with 100 dBA SPL for 8 hours per day in 5 consecutive days - and control group. After three days period of acclimatization to the experimental condition, rabbits hearing status in each group were measured by distortion product otoacoustic emissions on days zero means before the study was initiated as a baseline, eight, one hour after the latest exposure to noise, and ten. The recorded results were analyzed using SPSS software.Results: Highest mean distortion product otoacoustic emissions amplitudes in case group were allocated to frequencies of 5888.50 Hz, 8166.50 Hz, 9855.00 Hz, 3956.00 Hz, and 3098.50 Hz, respectively. However, the lowest mean distortion product otoacoustic emissions amplitude was related to frequency of 588.00 Hz (p=0.001.Conclusion: This study revealed that distortion product otoacoustic emissions amplitude shifts due to noise occur first in high and then in middle frequencies. Additionally, exposure to noise can decrease distortion product otoacoustic emissions amplitudes. We conclude that distortion product otoacoustic emissions can be a reliable test for estimating personal susceptibility to noise-induced hearing loss.

Comparative Effects of Different Balance-Training-Progression Styles on Postural Control and Ankle Force Production: A Randomized Controlled Trial.

Science.gov (United States)

Cuğ, Mutlu; Duncan, Ashley; Wikstrom, Erik

2016-02-01

Despite the effectiveness of balance training, the exact parameters needed to maximize the benefits of such programs remain unknown. One such factor is how individuals should progress to higher levels of task difficulty within a balance-training program. Yet no investigators have directly compared different balance-training-progression styles. To compare an error-based progression (ie, advance when proficient at a task) with a repetition-based progression (ie, advance after a set amount of repetitions) style during a balance-training program in healthy individuals. Randomized controlled trial. Research laboratory. A total of 28 (16 women, 12 men) physically healthy young adults (age = 21.57 ± 3.95 years, height = 171.60 ± 11.03 cm, weight = 72.96 ± 16.18 kg, body mass index = 24.53 ± 3.7). All participants completed 12 supervised balance-training sessions over 4 weeks. Each session consisted of a combination of dynamic unstable-surface tasks that incorporated a BOSU ball and lasted about 30 minutes. Static balance from an instrumented force plate, dynamic balance as measured via the Star Excursion Balance Test, and ankle force production in all 4 cardinal planes of motion as measured with a handheld dynamometer before and after the intervention. Selected static postural-control outcomes, dynamic postural control, and ankle force production in all planes of motion improved (P .05) for any of the outcome measures. A 4-week balance-training program consisting of dynamic unstable-surface exercises on a BOSU ball improved dynamic postural control and ankle force production in healthy young adults. These results suggest that an error-based balance-training program is comparable with but not superior to a repetition-based balance-training program in improving postural control and ankle force production in healthy young adults.

Resonant Higgs boson pair production in the $hh\\rightarrow b\\bar{b} \\; WW \\rightarrow b\\bar{b} \\ell^+ \

CERN Document Server

Martín Lozano, Víctor; Park, Chan Beom

2015-01-01

Adding a scalar singlet provides one of the simplest extensions of the Standard Model. In this work we briefly review the latest constraints on the mass and mixing of the new Higgs boson and study its production and decay at the LHC. We mainly focus on double Higgs production in the $hh \\rightarrow b \\bar{b} WW \\rightarrow b \\bar{b} \\ell^+ \

Stability and synchronization control of stochastic neural networks

CERN Document Server

Zhou, Wuneng; Zhou, Liuwei; Tong, Dongbing

2016-01-01

This book reports on the latest findings in the study of Stochastic Neural Networks (SNN). The book collects the novel model of the disturbance driven by Levy process, the research method of M-matrix, and the adaptive control method of the SNN in the context of stability and synchronization control. The book will be of interest to university researchers, graduate students in control science and engineering and neural networks who wish to learn the core principles, methods, algorithms and applications of SNN.

Control of quantum dynamics: The dream is alive

International Nuclear Information System (INIS)

Rabitz, H.

1995-01-01

In atomic and molecular physics, a long sought-after dream has been the use of optical fields to steer wavepackets into desired states. The inherent mechanism of such control consists of manipulating quantum mechanical constructive and destructive interferences. Finding the proper control fields is a problem of design, best expressed in terms of control theory. An overview of the latest developments in this field will be given, along with an indication of where the subject is heading. copyright 1995 American Institute of Physics

A Software Architecture for Control of Value Production in Federated Systems

Directory of Open Access Journals (Sweden)

Jay S. Bayne

2003-08-01

Full Text Available Federated enterprises are defined as interactive commercial entities that produce products and consume resources through a network of open, free-market transactions. Value production in such entities is defined as the real-time computation of enterprise value propositions. These computations are increasingly taking place in a grid-connected space – a space that must provide for secure, real-time, reliable end-to-end transactions governed by formal trading protocols. We present the concept of a value production unit (VPU as a key element of federated trading systems, and a software architecture for automation and control of federations of such VPUs.

Association of Controlled and Uncontrolled Hypertension With Workplace Productivity.

Science.gov (United States)

Unmuessig, Victoria; Fishman, Paul A; Vrijhoef, Hubertus J M; Elissen, Arianne M J; Grossman, David C

2016-03-01

The authors estimated the lost productive time (LPT) due to absenteeism and presenteeism among employees at the Group Health Cooperative with controlled and uncontrolled hypertension compared with normotensive patients. The patients responded to a survey inquiring about health behaviors with links to their medical record to identify diagnoses, blood pressure measurement, and prescription drug dispenses. Individuals with controlled hypertension were more likely to report any LPT relative to individuals with uncontrolled hypertension (40.6% vs 32.6%, Pabsenteeism compared with normotensive individuals (1.04 vs 0.59 hours; P=.001). Individuals with uncontrolled hypertension were more likely to report LPT due to absenteeism compared with individuals with controlled hypertension (1.35 vs 0.72 hours; P=.001). There were no significant differences between individuals with hypertension whose blood pressure was controlled and normotensive individuals with respect to the likelihood of reporting any LPT or in the amounts of absenteeism and presenteeism. © 2015 Wiley Periodicals, Inc.

Applying Trusted Network Technology To Process Control Systems

Science.gov (United States)

Okhravi, Hamed; Nicol, David

Interconnections between process control networks and enterprise networks expose instrumentation and control systems and the critical infrastructure components they operate to a variety of cyber attacks. Several architectural standards and security best practices have been proposed for industrial control systems. However, they are based on older architectures and do not leverage the latest hardware and software technologies. This paper describes new technologies that can be applied to the design of next generation security architectures for industrial control systems. The technologies are discussed along with their security benefits and design trade-offs.

New achievements in the EAST plasma control system

Energy Technology Data Exchange (ETDEWEB)

Yuan, Q.P., E-mail: qpyuan@ipp.ac.c [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Xiao, B.J. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Penaflor, B.G.; Piglowski, D.A. [General Atomics, DIII-D National Fusion Facility, San Diego, CA (United States); Liu, L.Z. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Johnson, R.D.; Walker, M.L.; Humphreys, D.A. [General Atomics, DIII-D National Fusion Facility, San Diego, CA (United States)

2010-07-15

In order to realize the low latency and distortion-free signal transmission between the plasma control system (PCS) and servo systems, the digital output structure configured with reflective memory board (RFM) was adopted in EAST PCS. And the enhanced performances are reported. Another achievement made in the latest EAST PCS was the implementation of density control algorithm, which controlled the line average density in either voltage or width modulation mode. The new integrated algorithm improved the precision of density calculation and control performance greatly. The details and experiment results are presented in this paper.

Weed control using ammonium nonanoate and cultivation in organic Vidalia sweet onion production

Science.gov (United States)

Ammonium nonanoate is registered for weed control in certified organic crop production and may be useful to control cool-season weeds in organic Vidalia® sweet onion. Cultivation with a tine weeder has been identified as a cost-effective means of weed control, but delays in cultivation cause some w...

Advances in the production of freeform optical surfaces

Science.gov (United States)

Tohme, Yazid E.; Luniya, Suneet S.

2007-05-01

Recent market demands for free-form optics have challenged the industry to find new methods and techniques to manufacture free-form optical surfaces with a high level of accuracy and reliability. Production techniques are becoming a mix of multi-axis single point diamond machining centers or deterministic ultra precision grinding centers coupled with capable measurement systems to accomplish the task. It has been determined that a complex software tool is required to seamlessly integrate all aspects of the manufacturing process chain. Advances in computational power and improved performance of computer controlled precision machinery have driven the use of such software programs to measure, visualize, analyze, produce and re-validate the 3D free-form design thus making the process of manufacturing such complex surfaces a viable task. Consolidation of the entire production cycle in a comprehensive software tool that can interact with all systems in design, production and measurement phase will enable manufacturers to solve these complex challenges providing improved product quality, simplified processes, and enhanced performance. The work being presented describes the latest advancements in developing such software package for the entire fabrication process chain for aspheric and free-form shapes. It applies a rational B-spline based kernel to transform an optical design in the form of parametrical definition (optical equation), standard CAD format, or a cloud of points to a central format that drives the simulation. This software tool creates a closed loop for the fabrication process chain. It integrates surface analysis and compensation, tool path generation, and measurement analysis in one package.

Improved GMP-compliant multi-dose production and quality control of 6-[18F]fluoro-L-DOPA.

Science.gov (United States)

Luurtsema, G; Boersma, H H; Schepers, M; de Vries, A M T; Maas, B; Zijlma, R; de Vries, E F J; Elsinga, P H

2017-01-01

6-[ 18 F]Fluoro-L-3,4-dihydroxyphenylalanine (FDOPA) is a frequently used radiopharmaceutical for detecting neuroendocrine and brain tumors and for the differential diagnosis of Parkinson's disease. To meet the demand for FDOPA, a high-yield GMP-compliant production method is required. Therefore, this study aimed to improve the FDOPA production and quality control procedures to enable distribution of the radiopharmaceutical over distances.FDOPA was prepared by electrophilic fluorination of the trimethylstannyl precursor with [ 18 F]F 2 , produced from [ 18 O] 2 via the double-shoot approach, leading to FDOPA with higher specific activity as compared to FDOPA which was synthesized, using [ 18 F]F 2 produced from 20 Ne, leading to FDOPA with a lower specific activity. The quality control of the product was performed using a validated UPLC system and compared with quality control with a conventional HPLC system. Impurities were identified using UPLC-MS. The [ 18 O] 2 double-shoot radionuclide production method yielded significantly more [ 18 F]F 2 with less carrier F 2 than the conventional method starting from 20 Ne. After adjustment of radiolabeling parameters substantially higher amounts of FDOPA with higher specific activity could be obtained. Quality control by UPLC was much faster and detected more side-products than HPLC. UPLC-MS showed that the most important side-product was FDOPA-quinone, rather than 6-hydroxydopa as suggested by the European Pharmacopoeia. The production and quality control of FDOPA were significantly improved by introducing the [ 18 O] 2 double-shoot radionuclide production method, and product analysis by UPLC, respectively. As a result, FDOPA is now routinely available for clinical practice and for distribution over distances.

Volatile products controlling Titan's tholins production

KAUST Repository

Carrasco, Nathalie

2012-05-01

A quantitative agreement between nitrile relative abundances and Titan\\'s atmospheric composition was recently shown with a reactor simulating the global chemistry occurring in Titan\\'s atmosphere (Gautier et al. [2011]. Icarus, 213, 625-635). Here we present a complementary study on the same reactor using an in situ diagnostic of the gas phase composition. Various initial N 2/CH 4 gas mixtures (methane varying from 1% to 10%) are studied, with a monitoring of the methane consumption and of the stable gas neutrals by in situ mass spectrometry. Atomic hydrogen is also measured by optical emission spectroscopy. A positive correlation is found between atomic hydrogen abundance and the inhibition function for aerosol production. This confirms the suspected role of hydrogen as an inhibitor of heterogeneous organic growth processes, as found in Sciamma-O\\'Brien et al. (Sciamma-O\\'Brien et al. [2010]. Icarus, 209, 704-714). The study of the gas phase organic products is focussed on its evolution with the initial methane amount [CH 4] 0 and its comparison with the aerosol production efficiency. We identify a change in the stationary gas phase composition for intermediate methane amounts: below [CH 4] 0=5%, the gas phase composition is mainly dominated by nitrogen-containing species, whereas hydrocarbons are massively produced for [CH 4] 0>5%. This predominance of N-containing species at lower initial methane amount, compared with the maximum gas-to solid conversion observed in Sciamma-O\\'Brien et al. (2010) for identical methane amounts confirms the central role played by N-containing gas-phase compounds to produce tholins. Moreover, two protonated imines (methanimine CH 2NH and ethanamine CH 3CHNH) are detected in the ion composition in agreement with Titan\\'s INMS measurements, and reinforcing the suspected role of these chemical species on aerosol production. © 2012 Elsevier Inc.

Quality control of clinker products by SEM and XRF analysis

International Nuclear Information System (INIS)

Ziad Abu Kaddourah; Khairun Azizi

1996-01-01

The microstructure and chemical properties of industrial Portland cement clinkers have been examined by SEM and XRF methods to establish the nature of the clinkers and how variations in the clinker characteristics can be used to control the clinker quality. The clinker nodules were found to show differences in the chemical composition and microstructure between the inner and outer parts of the clinker nodules. Microstructure studies of industrial Portland cement clinker have shown that the outer part of the nodules are enriched in silicate more than the inner part. There is better crystallization and larger alite crystal size in the outer part than in the inner part. The alite crystal size varied between 16.2 -46.12 μ m. The clinker chemical composition was found to affect the residual >45 μ m, where a higher belite content causes an increase in the residual >45 μ m in the the cement product and will cause a decrease in the concrete strength of the cement product. The aluminate and ferrite crystals and the microcracks within the alite crystal are clear in some clinker only. The quality of the raw material preparation, burning and cooling stages can be controlled using the microstructure of the clinker product

Production control system specified quality sausage products

Directory of Open Access Journals (Sweden)

A. V. Tokarev

2016-01-01

Full Text Available The problem of management of production target in technological system of production of sausages of the set quality is considered in article. Decomposition of technological system is considered. Functions of management are allocated: formation of an optimum compounding of forcemeat, expert analysis of a compounding, laboratory analysis of a compounding and its statement. Information technology of interaction of these functions is offered. The mathematical problem definition of finding of an optimum compounding meat product with use of possible substitutes of ingredients is presented. This mathematical problem is a classical linear programming problem whose solution has the standard program. Since the manufacture of the finished product are various nonlinear effects are taken into account at the present time it is practically impossible, the methodology provided in this operation "Expert analysis of the formulation" and "Laboratory analysis of the finished product." An example of calculating the optimum alternative base recipe "Sausages “Viennese with cheese”" TS 9213-010-40155161-2002. For an alternative formulation demands were made at a cost of meat, the ingredient composition, as well as the final product organoleptic and physic-chemical indicators should comply with regulatory requirements "Sausages “Viennese with cheese”" TS 9213-010-40155161-2002. Indicator acid activity (pH calculated stuffing formulation should be in the range 6.0-6.3. As a partial replacement for the main raw material have been proposed acceptable substitutes. It was necessary to calculate on the basis of the formulation "Sausages “Viennese with cheese”" TS 9213-010-40155161-2002 optimal price and quality alternative formulation. As a result of depreciation of the value of alternative stuffing recipe was 14,5 % when all of the restrictions on the consumer properties. The proposed information technology implemented in the software package "Multi

Effective production control in an automotive industry: MRP vs. demand-driven MRP

Science.gov (United States)

Shofa, Mohamad Jihan; Widyarto, Wahyu Oktri

2017-06-01

Material Requirements Planning (MRP) has deficiencies when dealing with current business environments, marked by a more complex network, a huge variety of products with longer lead time, and uncertain demands. This drives Demand-Driven MRP (DDMRP) approach to deal with those challenges. DDMRP is designed to connect the availability of materials and supplies directly from the actual condition using bills of materials (BOMs). Nevertheless, only few studies have scientifically proved the performance of DDMRP over MRP for controlling production and inventory control. Therefore, this research fills this gap by evaluating and comparing the performance of DDMRP and MRP in terms of level of effective inventory in the system. The evaluation was conducted through a simulation using data from an automotive company in Indonesia. The input parameters of scenarios were given for running the simulation. Based on the simulation, for the observed critical parts, DDMRP gave better results than MRP in terms of lead time and inventory level. DDMRP compressed the lead time part from 52 to 3 days (94% reduced) and, overall, the inventory level was in an effective condition. This suggests that DDMRP is more effective for controlling the production-inventory than MRP.

Optimizing models for production and inventory control using a genetic algorithm

Directory of Open Access Journals (Sweden)

Dragan S. Pamučar

2012-01-01

Full Text Available In order to make the Economic Production Quantity (EPQ model more applicable to real-world production and inventory control problems, in this paper we expand this model by assuming that some imperfect items of different product types being produced such as reworks are allowed. In addition, we may have more than one product and supplier along with warehouse space and budget limitation. We show that the model of the problem is a constrained non-linear integer program and propose a genetic algorithm to solve it. Moreover, a design of experiments is employed to calibrate the parameters of the algorithm for different problem sizes. In the end, a numerical example is presented to demonstrate the application of the proposed methodology.

The Laminated Marca Shale: High-Frequency Climate Cycles From the Latest Cretaceous

Science.gov (United States)