PLA composites: From production to properties.

Science.gov (United States)

Murariu, Marius; Dubois, Philippe

2016-12-15

Poly(lactic acid) or polylactide (PLA), a biodegradable polyester produced from renewable resources, is used for various applications (biomedical, packaging, textile fibers and technical items). Due to its inherent properties, PLA has a key-position in the market of biopolymers, being one of the most promising candidates for further developments. Unfortunately, PLA suffers from some shortcomings, whereas for the different applications specific end-use properties are required. Therefore, the addition of reinforcing fibers, micro- and/or nanofillers, and selected additives within PLA matrix is considered as a powerful method for obtaining specific end-use characteristics and major improvements of properties. This review highlights recent developments, current results and trends in the field of composites based on PLA. It presents the main advances in PLA properties and reports selected results in relation to the preparation and characterization of the most representative PLA composites. To illustrate the possibility to design the properties of composites, a section is devoted to the production and characterization of innovative PLA-based products filled with thermally-treated calcium sulfate, a by-product from the lactic acid production process. Moreover, are emphasized the last tendencies strongly evidenced in the case of PLA, i.e., the high interest to diversify its uses by moving from biomedical and packaging (biodegradation properties, "disposables") to technical applications ("durables"). Copyright © 2016 Elsevier B.V. All rights reserved.

Natural gas production verification tests

International Nuclear Information System (INIS)

1992-02-01

This Environmental Assessment (EA) has been prepared by the Department of Energy (DOE) in compliance with the requirements of the National Environmental Policy Act of 1969. The Department of Energy (DOE) proposes to fund, through a contract with Petroleum Consulting Services, Inc. of Canton, Ohio, the testing of the effectiveness of a non-water based hydraulic fracturing treatment to increase gas recovery from low-pressure, tight, fractured Devonian Shale formations. Although Devonian Shales are found in the Appalachian, Michigan, and Illinois Basins, testing will be done only in the dominant, historical five state area of established production. The objective of this proposed project is to assess the benefits of liquid carbon dioxide (CO 2 )/sand stimulations in the Devonian Shale. In addition, this project would evaluate the potential nondamaging (to the formation) properties of this unique fracturing treatment relative to the clogging or chocking of pores and fractures that act as gas flow paths to the wellbore in the target gas-producing zones of the formation. This liquid CO 2 /sand fracturing process is water-free and is expected to facilitate gas well cleanup, reduce the time required for post-stimulation cleanup, and result in improved production levels in a much shorter time than is currently experienced

Thermal and physical properties of bakery products.

Science.gov (United States)

Baik, O D; Marcotte, M; Sablani, S S; Castaigne, F

2001-07-01

This article reviews the measurement techniques, prediction models, and data on thermo-physical properties of bakery products: specific heat, thermal conductivity, thermal diffusivity, and density. Over the last decade, investigation has focused more on thermo-physical properties of nonbread bakery products. Both commonly used and new measurement techniques for thermo-physical properties reported in the publication are presented with directions for their proper use. Data and prediction models are tabulated for the range of moisture content and temperature of the bakery products.

Product information affects perception of sensory, collative properties and elicited emotions of Indonesian tempe

DEFF Research Database (Denmark)

Fibri, Dwi Larasatie Nur; Frøst, Michael Bom

The effects of product information given to consumers were evaluated on sensory and collative properties of tempe, a traditional Indonesian food. A consumer test on 9 different types of tempe (5 traditionally tempe and 4 more modernized version of tempe) was carried out with 175 Indonesian...... methods, where the traditional was most different from partly modernized and fully modernized. However, interaction is not systematic whether on bean or production type. Information changed the perception on sensory and collative properties of the products. The results demonstrate the powerful effect...... of sensory properties, rating of collative properties and elicited emotions. The results show astonishingly large effects of the information (table 1 and 2). The 5 traditional tempes (produced from velvet bean, black soybean, mungbean, jackbean, and local yellow soybean, all inoculated with traditional usar...

Composite Material from By-products and Its Properties

Science.gov (United States)

Šeps, K.; Broukalová, I.; Vodička, J.

2017-09-01

The paper shows an example of utilization of specific textile admixture - fluffs of torn textiles from waste cars in production of composite with aggregate consisting entirely of unsorted recycled concrete. The admixture in the mixture of recycled concrete and cement binder fills the pores and voids in composite. The elaborated composite has working title STEREDconcrete. In the article, basic mechanical-physical properties of the composite are presented also the fire resistance of STEREDconcrete, which was determined in tests.

Antimicrobials Products Tested or Pending Testing

Science.gov (United States)

The agency has completed testing of the majority of registered hospital disinfectants and tuberculocide products. The list of products can assist users in making informed choices regarding infection control in their facilities.

Transport properties of fission product vapors

International Nuclear Information System (INIS)

Im, K.H.; Ahluwalia, R.K.

1983-07-01

Kinetic theory of gases is used to calculate the transport properties of fission product vapors in a steam and hydrogen environment. Provided in tabular form is diffusivity of steam and hydrogen, viscosity and thermal conductivity of the gaseous mixture, and diffusivity of cesium iodide, cesium hydroxide, diatomic tellurium and tellurium dioxide. These transport properties are required in determining the thermal-hydraulics of and fission product transport in light water reactors

Milk Technological Properties as Affected by Including Artichoke By-Products Silages in the Diet of Dairy Goats

Directory of Open Access Journals (Sweden)

Raquel Muelas

2017-12-01

Full Text Available Traditional farming practices include the use of local agricultural by-products in the diet of ruminants. Artichoke harvesting and transformation yield high amounts of by-products that, if properly used, may reduce farming costs and the environmental impact of farming. The present study tests the inclusion of silages from artichoke by-products (plant and outer bracts in the diet of dairy goats (0%, 12.5% and 25% inclusion on the technological and sensory properties of milk during a five-month study. Milk composition, color, stability, coagulation and fermentation properties remained unaffected by diet changes. Panelists were not able to differentiate among yogurts obtained from those milks by discriminant triangular sensory tests. Silages of artichoke by-products can be included in isoproteic and isoenergetic diets for dairy goats, up to a 25% (feed dry matter, without negatively affecting milk technological and sensory properties whereas reducing feeding costs.

Mechanical properties used for the qualification of transport casks: Prototype development and extension to serial production

International Nuclear Information System (INIS)

Salzbrenner, R.; Crenshaw, T.B.; Sorenson, K.B.

1991-01-01

A thorough understanding of the mechanical behavior of material in a specific cask is required to properly analyze the structural response of the cask. An appropriate way to establish this understanding is through laboratory testing of cask material. The laboratory testing that was done to support the MOSAIK Drop Test Program is summarized as an example of how mechanical properties can be mapped for a prototype cask. The broad range behavior to be understood. This is necessary for the proper application of fracture mechanics, and focuses on fracture toughness as the inherent materials property which quantifies the fracture resistance of a material. The understanding established by a mechanics to a particular prototype, behavior of a prototype must be correctly associated with parameters which can be measured on production casks. Since the production casks cannot be destructively tested, measurements are commonly made on sub-size specimens. This may prevent direct measurement of valid design properties. An additional database may then be required to establish the correlation between sub-size specimen measurements and valid design properties. This is illustrated by outlining the additional testing which would be necessary to allow the successful verification of the MOSAIK Drop Test Program to be extended from the prototype to serially produced casks

Properties of raw materials and intermediate products in the production of uranium dioxide sintered tablets

International Nuclear Information System (INIS)

Landspersky, H.; Vanecek, I.; Podest, M.

1977-01-01

The properties are described of ammonium polyuranate and of powder uranium dioxide. Ammonium polyuranate, an intermediate product, is prepared by filtering the precipitate from uranyl nitrate solution precipitation, this either by an ammonia aqueous solution from a uranyl nitrate aqueous solution or by direct U 6+ precipitation from a TBP kerosene solution by aqueous concentrated ammonia. With relation to further processing, the major properties of the intermediate product include grain size, shape and appearance of crystallites, structure and thermal decomposition. These properties affect the properties of UO 2 , the following intermediate product obtained by reduction of ammonium polyuranate. Powder UO 2 is the final intermediate product; high-compacted UO 2 pellets are manufactured from it by compacting and sintering. The final product properties are affected by the following parameters: specific surface, grain size and shape, U/O ratio and compactibility. The effect of and the techniques of determining these parameters are shown. The necessity is emphasised of studying the properties of powder ammonium polyuranate because changes in its production technology affect the properties of further products. (J.P.)

Prediction of long-term properties of by-products - Technical and environmental properties in roads; Foerutsaegelse av laangtidsegenskaper hos restprodukter - Teknik och miljoe i vaegar

Energy Technology Data Exchange (ETDEWEB)

Arm, Maria; Suer, Pascal; Arvidsson, Haakan; Lindqvist, Jan-Erik; Frogner-Kockum, Paul; Larsson, Lennart; Toomvaeli, Cecilia

2008-12-15

In Sweden, use of industrial by-products is still hindered by concern for their long-term properties. This report describes a three-year research project aiming to: - Identify the key processes of ageing related to the usefulness of by-products in roads; - investigate the consequences of these processes for technical and environmental properties of the by-products, and - propose a method for accelerated ageing to predict the long-term properties. The project has compared naturally aged samples of two by-products used as sub-bases in existing asphalt paved roads with samples of fresh by-products from producers' piles. Steel slag of electric arc furnace type and municipal solid waste incinerator (MSWI) bottom ash was chosen. The samples were thoroughly characterized in order to identify which ageing processes had been crucial. The following properties were studied: grain size distribution, water content, compaction properties, deformation properties according to cyclic load triaxial tests, mineralogy and micro structure according to SEM and XRD, chemical composition, pH and leaching properties. For the bottom ash also organic content and electric conductivity was studied. Furthermore the pH was mapped in both roads and the conductivity was mapped in the bottom ash road. The working hypothesis was that ageing processes lead to changes in pH, effective particle size and mineralogy, which in turn determine leaching, stiffness and stability of the material. The test results confirmed that the pavement edge material is ageing faster than the road centre material is. In addition it was concluded that: - Steel slag from the pavement edge showed traces of carbonation and leaching processes, whereas slag from the road centre was identical to fresh slag. - Bottom ash from the pavement edge was more aged than bottom ash from the road centre. However, no difference in pH was found, instead the differences were said to be caused by differences in water exposure. - Water

A catalogue of crude oil and oil product properties, 1990

International Nuclear Information System (INIS)

Bobra, M.A.; Callaghan, S.

1990-09-01

This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 109 refs

A catalogue of crude oil and oil product properties, 1992

International Nuclear Information System (INIS)

Whiticar, S.; Bobra, M.; Liuzzo, P.; Callaghan, S.; Fingas, M.; Jokuty, P.; Ackerman, F.; Cao, J.

1993-02-01

This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 140 refs

Physical Properties for Lipids Based Process and Product Design

DEFF Research Database (Denmark)

Ana Perederic, Olivia; Kalakul, Sawitree; Sarup, Bent

Lipid processing covers several oil and fats technologies such as: edible oil production, biodieselproduction, oleochemicals (e.g.: food additives, detergents) and pharmaceutical product manufacturing. New demands regarding design and development of better products and more sustainable processes...... related to lipids technology, emerge according to consumers demanding improved product manufacturing from sustainable resources and new legislation regarding environmental safety [1]. Physical and thermodynamic property data and models for prediction of pure compound properties and mixtures properties...... involving lipids represent the basic and most important requirements for process product design, simulation and optimization. Experimentally measured values of involved compounds are desirable, but in most of the cases these are not available for all the compounds and properties needed. The lack...

Advanced productivity forecast using petrophysical wireline data calibrated with MDT tests and numerical reservoir simulation

Energy Technology Data Exchange (ETDEWEB)

Andre, Carlos de [PETROBRAS, Rio de Janeiro, RJ (Brazil); Canas, Jesus A.; Low, Steven; Barreto, Wesley [Schlumberger, Houston, TX (United States)

2004-07-01

This paper describes an integrated and rigorous approach for viscous and middle oil reservoir productivity evaluation using petrophysical models calibrated with permeability derived from mini tests (Dual Packer) and Vertical Interference Tests (VIT) from open hole wire line testers (MDT SLB TM). It describes the process from Dual Packer Test and VIT pre-job design, evaluation via analytical and inverse simulation modeling, calibration and up scaling of petrophysical data into a numerical model, history matching of Dual Packer Tests and VIT with numerical simulation modeling. Finally, after developing a dynamic calibrated model, we perform productivity forecasts of different well configurations (vertical, horizontal and multilateral wells) for several deep offshore oil reservoirs in order to support well testing activities and future development strategies. The objective was to characterize formation static and dynamic properties early in the field development process to optimize well testing design, extended well test (EWT) and support the development strategies in deep offshore viscous oil reservoirs. This type of oil has limitations to flow naturally to surface and special lifting equipment is required for smooth optimum well testing/production. The integrated analysis gave a good overall picture of the formation, including permeability anisotropy and fluid dynamics. Subsequent analysis of different well configurations and lifting schemes allows maximizing formation productivity. The simulation and calibration results are compared to measured well test data. Results from this work shows that if the various petrophysical and fluid properties sources are integrated properly an accurate well productivity model can be achieved. If done early in the field development program, this time/knowledge gain could reduce the risk and maximize the development profitability of new blocks (value of the information). (author)

Property Modelling and Databases in Product-Process Design

DEFF Research Database (Denmark)

Gani, Rafiqul; Sansonetti, Sascha

of the PC-SAFT is used. The developed database and property prediction models have been combined into a properties-software that allows different product-process design related applications. The presentation will also briefly highlight applications of the software for virtual product-process design...

Mechanical properties used for the qualification of transport casks: Prototype development and extension to serial production

International Nuclear Information System (INIS)

Salzbrenner, R.; Crenshaw, T.B.; Sorenson, K.B.

1992-01-01

A thorough understanding of the mechanical behavior of material in a specific cask is required to properly analyze the structural response of the cask. An appropriate way to establish this understanding is through laboratory testing of cask material. The laboratory testing that was done to support the MOSAIK Drop Test Program is summarized as an example of how mechanical properties can be mapped for a prototype cask. The broad range of measured properties allows the critical aspects of mechanical behavior to be understood. This is necessary for the proper application of fracture mechanics, and focuses on fracture toughness as the inherent materials property which quantifies the fracture resistance of a material. The general fracture mechanics approach and its application to specific cask designs are described elsewhere (Salzbrenner et al. 1990, Sorenson et al. 1992a, Sorenson et al. 1992b). The understanding established by a thorough mapping of the mechanical properties is necessary to apply fracture mechanics to a particular prototype, but it is not sufficient for qualifying serially produced casks. The mechanical behavior of a prototype must be correctly associated with parameters which can be measured on production casks. Since the production casks cannot be destructively tested, measurements are commonly made on sub-size specimens. This may prevent direct measurement of valid design properties. An additional database may then be required to establish the correlation between sub-size specimen measurements and valid design properties. This is illustrated by outlining the additional testing which would be necessary to allow the successful verification of the MOSAIK Drop Test Program to be extended from the prototype to serially produced casks

A data base and a standard material for use in acceptance testing of low-activity waste products

International Nuclear Information System (INIS)

Wolf, S.F.; Ebert, W.L.; Luo, J.S.; Strachan, D.M.

1998-04-01

The authors have conducted replicate dissolution tests following the product consistency test (PCT) procedure to measure the mean and standard deviation of the solution concentrations of B, Na, and Si at various combinations of temperature, duration, and glass/water mass ratio. Tests were conducted with a glass formulated to be compositionally similar to low-activity waste products anticipated for Hanford to evaluate the adequacy of test methods that have been designated in privatization contracts for use in product acceptance. An important finding from this set of tests is that the solution concentrations generated in tests at 20 C will likely be too low to measure the dissolution rates of waste products reliably. Based on these results, the authors recommend that the acceptance test be conducted at 40 C. Tests at 40 C generated higher solution concentrations, were more easily conducted, and the measured rates were easily related to those at 20 C. Replicate measurements of other glass properties were made to evaluate the possible use of LRM-1 as a standard material. These include its composition, homogeneity, density, compressive strength, the Na leachability index with the ANSI/ANS 16.1 leach test, and if the glass is characteristically hazardous with the toxicity characteristic leach procedure. The values of these properties were within the acceptable limits identified for Hanford low-activity waste products. The reproducibility of replicate tests and analyses indicates that the glass would be a suitable standard material

Properties of bituminization product from Olkiluoto power plant

International Nuclear Information System (INIS)

Valkiainen, M.; Vuorinen, U.

1985-09-01

In Finland, disposal into repositories excavated into bedrock on the present power plant sites is considered to be the most feasible alternative for the low- and intermediate level wastes. The Nuclear Waste Commission of the Finnish power companies has sponsored mainly experimental research work on long-term properties of bituminized ion exchange resin performed in the Reactor Laboratory of the Technical Research Centre of Finland since 1981. This report presents results on follow-up measurements of the leach tests started in 1981 and results on new leach tests with cement equilibrated water. Swelling of the bituminization product caused by water uptake is considered important. Both unrestricted and restricted swelling measurements were performed and are reported here. In addition to leaching and swelling also radiolytic gas generation and pH-changes of the leachant are discussed

Testing and Modeling of Machine Properties in Resistance Welding

DEFF Research Database (Denmark)

Wu, Pei

The objective of this work has been to test and model the machine properties including the mechanical properties and the electrical properties in resistance welding. The results are used to simulate the welding process more accurately. The state of the art in testing and modeling machine properties...... as real projection welding tests, is easy to realize in industry, since tests may be performed in situ. In part II, an approach of characterizing the electrical properties of AC resistance welding machines is presented, involving testing and mathematical modelling of the weld current, the firing angle...... in resistance welding has been described based on a comprehensive literature study. The present thesis has been subdivided into two parts: Part I: Mechanical properties of resistance welding machines. Part II: Electrical properties of resistance welding machines. In part I, the electrode force in the squeeze...

46 CFR 57.06-2 - Production test plate interval of testing.

Science.gov (United States)

2010-10-01

... WELDING AND BRAZING Production Tests § 57.06-2 Production test plate interval of testing. (a) At least one... 46 Shipping 2 2010-10-01 2010-10-01 false Production test plate interval of testing. 57.06-2... follows: (1) When the extent of welding on a single vessel exceeds 50 lineal feet of either or both...

Heavy Flavour Production and Properties at CMS and ATLAS

CERN Document Server

Barton, Adam Edward; The ATLAS collaboration

2018-01-01

Measurements of heavy flavour properties and production are an important part of the physics program of the ATLAS and CMS experiments at LHC. They can potentially expose physics beyond the standard model, constrain supersymmetry and advance hadron spectroscopy and test QCD. In the past years, the two collaborations have published results in several different fields, such as rare decays, searches for new states, CP and P violation and quarkonia polarisation. In this note, some of the most recent results from ATLAS and CMS are summarised.

Heavy Flavour Production and Properties at ATLAS and CMS

CERN Document Server

Barton, Adam Edward; The ATLAS collaboration

2017-01-01

Measurements of heavy flavour properties and production are an important part of the physics program of the ATLAS and CMS experiments at LHC. They can potentially expose physics beyond the standard model, constrain supersymmetry and advance hadron spectroscopy and test QCD. In the past years, the two collaborations have published results in several different fields, such as rare decays, searches for new states, CP and P violation and quarkonia polarization. In this note, some of the most recent results from ATLAS and CMS are summarized

A comparison of immunotoxic effects of nanomedicinal products with regulatory immunotoxicity testing requirements.

Science.gov (United States)

Giannakou, Christina; Park, Margriet Vdz; de Jong, Wim H; van Loveren, Henk; Vandebriel, Rob J; Geertsma, Robert E

2016-01-01

Nanomaterials (NMs) are attractive for biomedical and pharmaceutical applications because of their unique physicochemical and biological properties. A major application area of NMs is drug delivery. Many nanomedicinal products (NMPs) currently on the market or in clinical trials are most often based on liposomal products or polymer conjugates. NMPs can be designed to target specific tissues, eg, tumors. In virtually all cases, NMPs will eventually reach the immune system. It has been shown that most NMs end up in organs of the mononuclear phagocytic system, notably liver and spleen. Adverse immune effects, including allergy, hypersensitivity, and immunosuppression, have been reported after NMP administration. Interactions of NMPs with the immune system may therefore constitute important side effects. Currently, no regulatory documents are specifically dedicated to evaluate the immunotoxicity of NMs or NMPs. Their immunotoxicity assessment is performed based on existing guidelines for conventional substances or medicinal products. Due to the unique properties of NMPs when compared with conventional medicinal products, it is uncertain whether the currently prescribed set of tests provides sufficient information for an adequate evaluation of potential immunotoxicity of NMPs. The aim of this study was therefore, to compare the current regulatory immunotoxicity testing requirements with the accumulating knowledge on immunotoxic effects of NMPs in order to identify potential gaps in the safety assessment. This comparison showed that immunotoxic effects, such as complement activation-related pseudoallergy, myelosuppression, inflammasome activation, and hypersensitivity, are not readily detected by using current testing guidelines. Immunotoxicity of NMPs would be more accurately evaluated by an expanded testing strategy that is equipped to stratify applicable testing for the various types of NMPs.

Study of the mechanical properties of the electric power station components: the punch test

International Nuclear Information System (INIS)

Isselin, J.

2003-03-01

The aging of the electric production park implies an increasing need of knowledge concerning the evolution of the mechanical properties of its components. With regard to this problem, the availability in material is more and more small. This work proposes to characterize these properties through a mechanical test called Punch test. The main characteristic of this test is to use very small volume samples. The development of this test has been carried out by the study of a 15 MDV 4-05 steel coming from a steam drum of a thermal power plant after 145000 hours of service. At first, we have measured the influence of the parameters of this test. Then, the study has dealt more particularly on the transition temperature of the material. With the finite element simulation method, the strain hardening coefficient of the material has been determined. (O.M.)

Measurement properties of continuous text reading performance tests.

Science.gov (United States)

Brussee, Tamara; van Nispen, Ruth M A; van Rens, Ger H M B

2014-11-01

Measurement properties of tests to assess reading acuity or reading performance have not been extensively evaluated. This study aims to provide an overview of the literature on available continuous text reading tests and their measurement properties. A literature search was performed in PubMed, Embase and PsycInfo. Subsequently, information on design and content of reading tests, study design and measurement properties were extracted using consensus-based standards for selection of health measurement instruments. Quality of studies, reading tests and measurement properties were systematically assessed using pre-specified criteria. From 2334 identified articles, 20 relevant articles were found on measurement properties of three reading tests in various languages: IReST, MNread Reading Test and Radner Reading Charts. All three reading tests scored high on content validity. Reproducibility studies (repeated measurements between different testing sessions) of the IReST and MNread of commercially available reading tests in different languages were missing. The IReST scored best on inter-language comparison, the MNread scored well in repeatability studies (repeated measurements under the same conditions) and the Radner showed good reproducibility in studies. Although in daily practice there are other continuous text reading tests available meeting the criteria of this review, measurement properties were described in scientific studies for only three of them. Of the few available studies, the quality and content of study design and methodology used varied. For testing existing reading tests and the development of new ones, for example in other languages, we make several recommendations, including careful description of patient characteristics, use of objective and subjective lighting levels, good control of working distance, documentation of the number of raters and their training, careful documentation of scoring rules and the use of Bland-Altman analyses or similar for

Nuclear waste glass product consistency test (PCT): Version 7.0. Revision 3

International Nuclear Information System (INIS)

Jantzen, C.M.; Bibler, N.E.; Beam, D.C.; Ramsey, W.G.

1994-06-01

Liquid high-level nuclear waste will be immobilized at the Savannah River Site (SRS) by vitrification in borosilicate glass. The glass will be produced in the Defense Waste Processing Facility (DWPF), poured into stainless steel canisters, and eventually disposed of in a geologic repository. In order to comply with the Waste Acceptance Product Specifications (WAPS), the durability of the glass needs to be measured during production to assure its long term stability and radionuclide release properties. A durability test, designated the Product Consistency Test (PCT), was developed for DWPF glass in order to meet the WAPS requirements. The response of the PCT procedure was based on extensive testing with glasses of widely different compositions. The PCT was determined to be very reproducible, to yield reliable results rapidly, and to be easily performed in shielded cell facilities with radioactive samples. Version 7.0 of the PCT procedure is attached. This draft version has been submitted to ASTM for full committee (C26, Nuclear Fuel Cycle) ballot after being balloted successfully through subcommittee C26.13 on Repository Waste Package Materials Testing

The influence of testing apparatus stiffness on the source properties of laboratory stick-slip

Science.gov (United States)

Kilgore, B. D.; McGarr, A.; Beeler, N. M.; Lockner, D. A.

2016-12-01

Stick-slip experiments were performed to determine the influence of the testing apparatus stiffness on source properties, to develop methods to relate stick-slip to natural earthquakes, and to examine the hypothesis of McGarr [2012] that the product of unloading stiffness, k, and slip duration, T, is both scale-independent and approximately constant for both laboratory and natural earthquakes. A double-direct shear load frame was used with Sierra White Granite samples at 2 MPa normal stress, and a remote loading rate of 0.2 µm/s. The stiffness of the test apparatus was varied by more than an order of magnitude by inserting disk springs into the shear loading column adjacent to the granite samples. Servo-controlling slip at a point between the forcing ram and the shear force load cell, produced repeatable slip events. Slip and slip duration decrease as k increases, as they do for natural earthquakes. In contrast to earthquakes, stress drop and slip rate decrease with increasing k, and the product kT for these experiments is not constant, but decreases with k. These data, collected over a range of k, do not conform to McGarr's [2012] hypothesis. However, analysis of stick-slip studies from other testing apparatuses is consistent with McGarr's hypothesis; kT is scale-independent, similar to that of earthquakes, equal to the ratio of static stress drop to average slip velocity, and similar to the ratio of shear modulus to wavespeed of rock. These properties result from conducting experiments over a range of sample sizes, using rock samples with the same elastic properties as the Earth, and using testing machines whose stiffnesses decrease, and characteristic periods increase with scale. A consequence of our experiments and analysis is that extrapolation of lab scale earthquake source properties to the Earth is more difficult than previously thought, requiring an accounting for the properties of the testing machines and additional research beyond that reported here.

Production, microstructure and mechanical properties of two different austenitic ODS steels

Energy Technology Data Exchange (ETDEWEB)

Gräning, T., E-mail: tim.graening@kit.edu; Rieth, M.; Hoffmann, J.; Möslang, A.

2017-04-15

This article is to summarize and examine processing parameters of novel developed austenitic oxide dispersed strengthened (ODS) steels. Comparing hot-rolled and extruded conditions after the same degree of deformation after and before annealing, are just some examples to give insights into the complex processing of austenitic ODS steels. One of the major drawbacks of the material is the more sophisticated production process. Due to a ductile matrix material with an increased stickiness during milling, a two-step milling procedure with the use of ZrO{sub 2} milling balls was applied to raise the production yield and to use the abrasion of the ZrO{sub 2} as an additional element to facilitate the formation of nano-sized precipitates. To get a better understanding how the different powder particle sizes after milling affect final properties, sieving was applied and revealed a serious effect in terms of precipitate size, distribution and mechanical properties. Grain sizes in relation to the precipitate size, annealing time and processing parameters were determined and compared to the mechanical properties. Hardness and tensile test have pointed out, that the precipitate size and number are more important in respect to the ultimate tensile strength than the grain size and that in this study hot-rolled material exhibited the better properties. The investigation of the microstructure illustrated the stability of precipitates during annealing at 1100 °C for 40 h. These heat treatments also led to a consistent grain size, due to the pinning effect of the grain boundaries, caused by precipitates. - Highlights: •Comparison of the microstructure of extruded and hot-rolled ODS. •Two-step mechanical alloying with ZrO{sub 2} milling balls. •Determination of precipitate size distribution depending on chemical composition and annealing times. •Determination of the influence of sieving of mechanical alloyed powder on the near net shape products. •Tensile tests of two

Electromagnetic radiation properties of foods and agricultural products

International Nuclear Information System (INIS)

Mohsenin, N.N.

1984-01-01

In this book, the author examines the effects of the various regions of the electromagnetic radiation spectrum on foods and agricultural products. Among the regions of the electromagnetic radiation spectrum covered are high-energy beta and neutron particles, gamma-rays and X-rays, to lower-energy visible, near infrared, infrared, microwave and low-energy radiowaves and electric currents. Dr. Mohsenin applies these electromagnetic phenomena to food products such as fruits, vegetables, seeds, dairy products, meat and processed foods. Contents: Some Basic Concepts of Electromagnetic Radiation. Basic Instruments for Measurement of Optical Properties. Applications of Radiation in the Visible Spectrum. Color and its Measurement. Sorting for Color and Appearance. Near-Infrared and Infrared Radiation Applications. Applications of High-Energy Radiation. Related Concepts of Microwaves, Radiowaves, and Electric Currents. Measurement of Electrical Properties of Foods and Agricultural Products. Applications of Electrical Properties. Appendix, Cited References. Subject Index

Property Based Process and Product Synthesis and Design

DEFF Research Database (Denmark)

Eden, Mario Richard

2003-01-01

in terms of the constitutive (synthesis/design) variables instead of the process variables, thus providing the synthesis/design targets. The second reverse problem (reverse property prediction) solves the constitutive equations to identify unit operations, operating conditions and/or products by matching......This thesis describes the development of a general framework for solving process and product design problems. Targeting the desired performance of the system in a systematic manner relieves the iterative nature of conventional design techniques. Furthermore, conventional component based methods...... are not capable of handling problems, where the process or product objectives are driven by functionalities or properties rather than chemical constituency. The framework is meant to complement existing composition based methods by being able to handle property driven problems. By investigating the different...

Test benches for studying the properties of car tyres

Science.gov (United States)

Kuznetsov, N. Yu.; Fedotov, A. I.; Vlasov, V. G.

2017-12-01

The article describes the design of the measuring systems of test benches used to study the properties of elastic tyres. The bench has two autonomous systems - for testing the braking properties of elastic tyres rolling in a plane parallel way and for testing tyre slip properties. The system for testing braking properties determines experimental characteristics of elastic tyres as the following dependencies: longitudinal response vs time, braking torque vs slip, angular velocity vs slip, and longitudinal response vs slip. The system for studying tyre slip properties determines both steady (dependence of the lateral response in a contact area on the slipping angle) and non-steady characteristics (time variation of the slipping angle as a result of turning from -40 to +40 degrees) of tyre slip. The article presents the diagrams of bench tests of elastic tyres. The experimental results show metrological parameters and functional capabilities of the bench for studying tyre properties in driving and braking modes. The metrological indices of the recorded parameters of the measuring system for studying tyre properties are presented in the table.

Prediction of thermo-physical properties of liquid formulated products

DEFF Research Database (Denmark)

Mattei, Michele; Conte, Elisa; Kontogeorgis, Georgios

2013-01-01

The objective of this chapter is to give an overview of the models, methods and tools that may be used for the estimation of liquid formulated products. First a classification of the products is given and the thermo-physical properties needed to represent their functions are listed. For each...... property, a collection of the available models are presented according to the property type and the model type. It should be noted, however, that the property models considered or highlighted in this chapter are only examples and are not necessarily the best and most accurate for the corresponding property....

A comparison of immunotoxic effects of nanomedicinal products with regulatory immunotoxicity testing requirements

Directory of Open Access Journals (Sweden)

Giannakou C

2016-06-01

Full Text Available Christina Giannakou,1,2 Margriet VDZ Park,1 Wim H de Jong,1 Henk van Loveren,1,2 Rob J Vandebriel,1 Robert E Geertsma1 1Centre for Health Protection, National Institute for Public Health and the Environment (RIVM, Bilthoven, 2Department of Toxicogenomics, Maastricht University, Maastricht, the Netherlands Abstract: Nanomaterials (NMs are attractive for biomedical and pharmaceutical applications because of their unique physicochemical and biological properties. A major application area of NMs is drug delivery. Many nanomedicinal products (NMPs currently on the market or in clinical trials are most often based on liposomal products or polymer conjugates. NMPs can be designed to target specific tissues, eg, tumors. In virtually all cases, NMPs will eventually reach the immune system. It has been shown that most NMs end up in organs of the mononuclear phagocytic system, notably liver and spleen. Adverse immune effects, including allergy, hypersensitivity, and immunosuppression, have been reported after NMP administration. Interactions of NMPs with the immune system may therefore constitute important side effects. Currently, no regulatory documents are specifically dedicated to evaluate the immunotoxicity of NMs or NMPs. Their immunotoxicity assessment is performed based on existing guidelines for conventional substances or medicinal products. Due to the unique properties of NMPs when compared with conventional medicinal products, it is uncertain whether the currently prescribed set of tests provides sufficient information for an adequate evaluation of potential immunotoxicity of NMPs. The aim of this study was therefore, to compare the current regulatory immunotoxicity testing requirements with the accumulating knowledge on immunotoxic effects of NMPs in order to identify potential gaps in the safety assessment. This comparison showed that immunotoxic effects, such as complement activation-related pseudoallergy, myelosuppression, inflammasome

The computation of properties of injection-moulded products

NARCIS (Netherlands)

Douven, L.F.A.; Baaijens, F.P.T.; Meijer, H.E.H.

1995-01-01

Injection moulding is a flexible production technique for the manufacture of complex shaped, thin walled polymer products that require minimal finishing. During processing, the polymer experiences a complex deformation and temperature history that affects the final properties of the product. In a

Property transfer assessments should include radon gas testing

International Nuclear Information System (INIS)

Nardi, M.A.

1992-01-01

There are two emerging influences that will require radon gas testing as part of many property transfers and most environmental assessments. These requirements come from lending regulators and state legislatures and affect single family, multifamily, and commercial properties. Fannie Mae and others have developed environmental investigation guidelines for protection from long term legal liabilities in the purchase of environmentally contaminated real estate. These guidelines include radon gas testing for many properties. Several states have enacted laws that require environmental disclosure forms be prepared to ensure that the parties involved in certain real estate transactions are aware of the environmental liabilities that may come with the transfer of property. Indiana has recently enacted legislation that would require the disclosure of the presence of radon gas on many commercial real estate transactions. With more banks and state governments following this trend, radon gas testing should be performed during all property transfers and environmental assessments to protect the parties involved from any long term legal liabilities

ATLAS + CMS top production and properties: Run 1 legacy

CERN Document Server

AUTHOR|(SzGeCERN)641905; The ATLAS collaboration

2015-01-01

The large Run 1 data sample of top-quark events collected at the Large Hadron Collider allows a variety of measurements to analyse the production and properties of the top quark. Measurements of top-quark production cross sections and top-quark properties in proton-proton collisions with the ATLAS and CMS detectors at the LHC are presented.

A Review on Biomass Torrefaction Process and Product Properties

Energy Technology Data Exchange (ETDEWEB)

Jaya Shankar Tumuluru; Shahab Sokhansanj; Christopher T. Wright; J. Richard Hess; Richard D. Boardman

2011-08-01

Biomass Torrefaction is gaining attention as an important preprocessing step to improve the quality of biomass in terms of physical properties and chemical composition. Torrefaction is a slow heating of biomass in an inert or reduced environment to a maximum temperature of approximately 300 C. Torrefaction can also be defined as a group of products resulting from the partially controlled and isothermal pyrolysis of biomass occurring in a temperature range of 200-280 C. Thus, the process can be called a mild pyrolysis as it occurs at the lower temperature range of the pyrolysis process. At the end of the torrefaction process, a solid uniform product with lower moisture content and higher energy content than raw biomass is produced. Most of the smoke-producing compounds and other volatiles are removed during torrefaction, which produces a final product that will have a lower mass but a higher heating value. The present review work looks into (a) torrefaction process and different products produced during the process and (b) solid torrefied material properties which include: (i) physical properties like moisture content, density, grindability, particle size distribution and particle surface area and pelletability; (ii) chemical properties like proximate and ultimate composition; and (iii) storage properties like off-gassing and spontaneous combustion.

Endurance test for IR rig for RI production assembly (test procedure)

International Nuclear Information System (INIS)

Chung, Heung June; Ryu, Jeong Soo

2000-08-01

This test procedure details the test loop, test method, and test procedure for pressure drop, vibration and endurance test of IR Rig for RI production. From the pressure drop test, the hydraulic design requirements of the capsule are verified. HANARO limit condition is checked and the compatibility with HANARO core is verified. From flow induced vibration test vibration frequency and displacement are investigated. The wear of IR Rig is investigated through endurance test, and these data are used to evaluate the expected wear at maximum resident time of the IR Rig for RI production

Properties Important To Mixing For WTP Large Scale Integrated Testing

International Nuclear Information System (INIS)

Koopman, D.; Martino, C.; Poirier, M.

2012-01-01

Large Scale Integrated Testing (LSIT) is being planned by Bechtel National, Inc. to address uncertainties in the full scale mixing performance of the Hanford Waste Treatment and Immobilization Plant (WTP). Testing will use simulated waste rather than actual Hanford waste. Therefore, the use of suitable simulants is critical to achieving the goals of the test program. External review boards have raised questions regarding the overall representativeness of simulants used in previous mixing tests. Accordingly, WTP requested the Savannah River National Laboratory (SRNL) to assist with development of simulants for use in LSIT. Among the first tasks assigned to SRNL was to develop a list of waste properties that matter to pulse-jet mixer (PJM) mixing of WTP tanks. This report satisfies Commitment 5.2.3.1 of the Department of Energy Implementation Plan for Defense Nuclear Facilities Safety Board Recommendation 2010-2: physical properties important to mixing and scaling. In support of waste simulant development, the following two objectives are the focus of this report: (1) Assess physical and chemical properties important to the testing and development of mixing scaling relationships; (2) Identify the governing properties and associated ranges for LSIT to achieve the Newtonian and non-Newtonian test objectives. This includes the properties to support testing of sampling and heel management systems. The test objectives for LSIT relate to transfer and pump out of solid particles, prototypic integrated operations, sparger operation, PJM controllability, vessel level/density measurement accuracy, sampling, heel management, PJM restart, design and safety margin, Computational Fluid Dynamics (CFD) Verification and Validation (V and V) and comparison, performance testing and scaling, and high temperature operation. The slurry properties that are most important to Performance Testing and Scaling depend on the test objective and rheological classification of the slurry (i

PROPERTIES IMPORTANT TO MIXING FOR WTP LARGE SCALE INTEGRATED TESTING

Energy Technology Data Exchange (ETDEWEB)

Koopman, D.; Martino, C.; Poirier, M.

2012-04-26

Large Scale Integrated Testing (LSIT) is being planned by Bechtel National, Inc. to address uncertainties in the full scale mixing performance of the Hanford Waste Treatment and Immobilization Plant (WTP). Testing will use simulated waste rather than actual Hanford waste. Therefore, the use of suitable simulants is critical to achieving the goals of the test program. External review boards have raised questions regarding the overall representativeness of simulants used in previous mixing tests. Accordingly, WTP requested the Savannah River National Laboratory (SRNL) to assist with development of simulants for use in LSIT. Among the first tasks assigned to SRNL was to develop a list of waste properties that matter to pulse-jet mixer (PJM) mixing of WTP tanks. This report satisfies Commitment 5.2.3.1 of the Department of Energy Implementation Plan for Defense Nuclear Facilities Safety Board Recommendation 2010-2: physical properties important to mixing and scaling. In support of waste simulant development, the following two objectives are the focus of this report: (1) Assess physical and chemical properties important to the testing and development of mixing scaling relationships; (2) Identify the governing properties and associated ranges for LSIT to achieve the Newtonian and non-Newtonian test objectives. This includes the properties to support testing of sampling and heel management systems. The test objectives for LSIT relate to transfer and pump out of solid particles, prototypic integrated operations, sparger operation, PJM controllability, vessel level/density measurement accuracy, sampling, heel management, PJM restart, design and safety margin, Computational Fluid Dynamics (CFD) Verification and Validation (V and V) and comparison, performance testing and scaling, and high temperature operation. The slurry properties that are most important to Performance Testing and Scaling depend on the test objective and rheological classification of the slurry (i

Towards standardized testing methodologies for optical properties of components in concentrating solar thermal power plants

Science.gov (United States)

Sallaberry, Fabienne; Fernández-García, Aránzazu; Lüpfert, Eckhard; Morales, Angel; Vicente, Gema San; Sutter, Florian

2017-06-01

Precise knowledge of the optical properties of the components used in the solar field of concentrating solar thermal power plants is primordial to ensure their optimum power production. Those properties are measured and evaluated by different techniques and equipment, in laboratory conditions and/or in the field. Standards for such measurements and international consensus for the appropriate techniques are in preparation. The reference materials used as a standard for the calibration of the equipment are under discussion. This paper summarizes current testing methodologies and guidelines for the characterization of optical properties of solar mirrors and absorbers.

Tobacco and Nicotine Product Testing

Science.gov (United States)

Biener, Lois; Leischow, Scott J.; Zeller, Mitch R.

2012-01-01

Introduction: Tobacco product testing is a critical component of the Family Smoking Prevention and Tobacco Control Act (FSPTCA), which grants the Food and Drug Administration the authority to regulate tobacco products. The availability of methods and measures that can provide accurate data on the relative health risks across types of tobacco products, brands, and subbrands of tobacco products on the validity of any health claims associated with a product, and on how consumers perceive information on products toxicity or risks is crucial for making decisions on the product's potential impact on public health. These tools are also necessary for making assessments of the impact of new indications for medicinal products (other than cessation) but more importantly of tobacco products that may in the future be marketed as cessation tools. Objective: To identify research opportunities to develop empirically based and comprehensive methods and measures for testing tobacco and other nicotine-containing products so that the best science is available when decisions are made about products or policies. Methods: Literature was reviewed to address sections of the FSPTCA relevant to tobacco product evaluation; research questions were generated and then reviewed by a committee of research experts. Results: A research agenda was developed for tobacco product evaluation in the general areas of toxicity and health risks, abuse liability, consumer perception, and population effects. Conclusion: A cohesive, systematic, and comprehensive assessment of tobacco products is important and will require building consensus and addressing some crucial research questions. PMID:21460383

Additive Manufacturing and Casting Technology Comparison: Mechanical Properties, Productivity and Cost Benchmark

Science.gov (United States)

Vevers, A.; Kromanis, A.; Gerins, E.; Ozolins, J.

2018-04-01

The casting technology is one of the oldest production technologies in the world but in the recent years metal additive manufacturing also known as metal 3D printing has been evolving with huge steps. Both technologies have capabilities to produce parts with internal holes and at first glance surface roughness is similar for both technologies, which means that for precise dimensions parts have to be machined in places where precise fit is necessary. Benchmark tests have been made to find out if parts which are produced with metal additive manufacturing can be used to replace parts which are produced with casting technology. Most of the comparative tests have been made with GJS-400-15 grade which is one of the most popular cast iron grades. To compare mechanical properties samples have been produced using additive manufacturing and tested for tensile strength, hardness, surface roughness and microstructure and then the results have been compared with the samples produced with casting technology. In addition, both technologies have been compared in terms of the production time and production costs to see if additive manufacturing is competitive with the casting technology. The original paper has been written in the Latvian language as part of the Master Thesis within the framework of the production technology study programme at Riga Technical University.

46 CFR 57.06-5 - Production toughness testing.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Production toughness testing. 57.06-5 Section 57.06-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING WELDING AND BRAZING Production Tests § 57.06-5 Production toughness testing. (a) In addition to the test specimens required by...

Cartesian product of hypergraphs: properties and algorithms

Directory of Open Access Journals (Sweden)

Alain Bretto

2009-09-01

Full Text Available Cartesian products of graphs have been studied extensively since the 1960s. They make it possible to decrease the algorithmic complexity of problems by using the factorization of the product. Hypergraphs were introduced as a generalization of graphs and the definition of Cartesian products extends naturally to them. In this paper, we give new properties and algorithms concerning coloring aspects of Cartesian products of hypergraphs. We also extend a classical prime factorization algorithm initially designed for graphs to connected conformal hypergraphs using 2-sections of hypergraphs.

46 CFR 54.05-16 - Production toughness testing.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Production toughness testing. 54.05-16 Section 54.05-16... Toughness Tests § 54.05-16 Production toughness testing. (a) For vessels of welded construction, production... welding procedures shall be the same as used in the fabrication of the vessel. From each test plate, one...

Statistical properties of entropy production derived from fluctuation theorems

International Nuclear Information System (INIS)

Merhav, Neri; Kafri, Yariv

2010-01-01

Several implications of well-known fluctuation theorems, on the statistical properties of entropy production, are studied using various approaches. We begin by deriving a tight lower bound on the variance of the entropy production for a given mean of this random variable. It is shown that the Evans–Searles fluctuation theorem alone imposes a significant lower bound on the variance only when the mean entropy production is very small. It is then nonetheless demonstrated that upon incorporating additional information concerning the entropy production, this lower bound can be significantly improved, so as to capture extensivity properties. Another important aspect of the fluctuation properties of the entropy production is the relationship between the mean and the variance, on the one hand, and the probability of the event where the entropy production is negative, on the other hand. Accordingly, we derive upper and lower bounds on this probability in terms of the mean and the variance. These bounds are tighter than previous bounds that can be found in the literature. Moreover, they are tight in the sense that there exist probability distributions, satisfying the Evans–Searles fluctuation theorem, that achieve them with equality. Finally, we present a general method for generating a wide class of inequalities that must be satisfied by the entropy production. We use this method to derive several new inequalities that go beyond the standard derivation of the second law

Chemical Characterization and Reactivity Testing of Fuel-Oxidizer Reaction Product (Test Report)

Science.gov (United States)

1996-01-01

The product of incomplete reaction of monomethylhydrazine (MMH) and nitrogen tetroxide (NTO) propellants, or fuel-oxidizer reaction product (FORP), has been hypothesized as a contributory cause of an anomaly which occurred in the chamber pressure (PC) transducer tube on the Reaction Control Subsystem (RCS) aft thruster 467 on flight STS-51. A small hole was found in the titanium-alloy PC tube at the first bend below the pressure transducer. It was surmised that the hole may have been caused by heat and pressure resulting from ignition of FORP. The NASA Johnson Space Center (JSC) White Sands Test Facility (WSTF) was requested to define the chemical characteristics of FORP, characterize its reactivity, and simulate the events in a controlled environment which may have lead to the Pc-tube failure. Samples of FORP were obtained from the gas-phase reaction of MMH with NTO under laboratory conditions, the pulsed firings of RCS thrusters with modified PC tubes using varied oxidizer or fuel lead times, and the nominal RCS thruster firings at WSTF and Kaiser-Marquardt. Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), accelerating rate calorimetry (ARC), ion chromatography (IC), inductively coupled plasma (ICP) spectrometry, thermogravimetric analysis (TGA) coupled to FTIR (TGA/FTIR), and mechanical impact testing were used to qualitatively and quantitatively characterize the chemical, thermal, and ignition properties of FORP. These studies showed that the composition of FORP is variable but falls within a limited range of compositions that depends on the fuel loxidizer ratio at the time of formation, composition of the post-formation atmosphere (reducing or oxidizing), and reaction or postreaction temperature. A typical composition contains methylhydrazinium nitrate (MMHN), ammonium nitrate (AN), methylammonium nitrate (MAN), and trace amounts of hydrazinium nitrate and 1,1-dimethylhydrazinium nitrate. The thermal decomposition

Nuclear waste glass product consistency test (PCT), Version 5.0

International Nuclear Information System (INIS)

Jantzen, C.M.; Bibler, N.E.; Beam, D.C.; Ramsey, W.G.; Waters, B.J.

1992-06-01

Liquid high-level nuclear waste will be immobilized at the Savannah River Site (SRS) by vitrification in borosilicate glass. The glass will be produced in the Defense Waste Processing Facility (DWPF), poured into stainless steel canisters, and eventually disposed of in a geologic repository. In order to comply with the Waste Acceptance Preliminary Specifications (WAPS), the durability of the glass needs to be measured during production to assure its long term stability and radionuclide release properties. A durability test, designated the Produce Consistency Test (PCT), was developed for DWPF glass in order to meet the WAPS requirements. The response of the PCT procedure was based on extensive testing with glasses of widely different compositions. The PCT was determined to be very reproducible, to yield reliable results rapidly, and to be easily performed in shielded cell facilities with radioactive samples. Version 5.0 of the PCT procedure is attached

Performance test results of mock-up test facility of HTTR hydrogen production system

International Nuclear Information System (INIS)

Ohashi, Hirofumi; Inaba, Yoshitomo; Nishihara, Tetsuo

2004-01-01

For the purpose to demonstrate effectiveness of high-temperature nuclear heat utilization, Japan Atomic Energy Research Institute has been developing a hydrogen production system and has planned to connect the hydrogen production system to High Temperature Engineering Test Reactor (HTTR). Prior to construction of a HTTR hydrogen production system, a mock-up test facility was constructed to investigate transient behavior of the hydrogen production system and to establish system controllability. The Mock-up test facility with a full-scale reaction tube is an approximately 1/30-scale model of the HTTR hydrogen production system and an electric heater is used as a heat source instead of a reactor. After its construction, a performance test of the test facility was carried out in the same pressure and temperature conditions as those of the HTTR hydrogen production system to investigate its performance such as hydrogen production ability, controllability and so on. It was confirmed that hydrogen was stably produced with a hot helium gas about 120m 3 /h, which satisfy the design value, and thermal disturbance of helium gas during the start-up could be mitigated within the design value by using a steam generator. The mock-up test of the HTTR hydrogen production system using this facility will continue until 2004. (author)

Production, microstructure and mechanical properties of two different austenitic ODS steels

Science.gov (United States)

Gräning, T.; Rieth, M.; Hoffmann, J.; Möslang, A.

2017-04-01

This article is to summarize and examine processing parameters of novel developed austenitic oxide dispersed strengthened (ODS) steels. Comparing hot-rolled and extruded conditions after the same degree of deformation after and before annealing, are just some examples to give insights into the complex processing of austenitic ODS steels. One of the major drawbacks of the material is the more sophisticated production process. Due to a ductile matrix material with an increased stickiness during milling, a two-step milling procedure with the use of ZrO2 milling balls was applied to raise the production yield and to use the abrasion of the ZrO2 as an additional element to facilitate the formation of nano-sized precipitates. To get a better understanding how the different powder particle sizes after milling affect final properties, sieving was applied and revealed a serious effect in terms of precipitate size, distribution and mechanical properties. Grain sizes in relation to the precipitate size, annealing time and processing parameters were determined and compared to the mechanical properties. Hardness and tensile test have pointed out, that the precipitate size and number are more important in respect to the ultimate tensile strength than the grain size and that in this study hot-rolled material exhibited the better properties. The investigation of the microstructure illustrated the stability of precipitates during annealing at 1100 °C for 40 h. These heat treatments also led to a consistent grain size, due to the pinning effect of the grain boundaries, caused by precipitates.

Production and test of the LHCb Muon Chamber

CERN Multimedia

2005-01-01

- The Muon System of LHCb - The Multi-Wire Proportional Chambers for LHCb - Wire tension meter - Wire pitch measurement - Gas leakage test - Test with cosmic rays - Production and test summary - Gap gain uniformity - Production and test summary

Fibrin degradation products blood test

Science.gov (United States)

... behind when clots dissolve in the blood. A blood test can be done to measure these products. ... Certain medicines can change blood test results. Tell your health care provider about all the medicines you take. Your provider will tell you if you need ...

Molecular characterization, technological properties and safety aspects of enterococci from 'Hussuwa', an African fermented sorghum product.

Science.gov (United States)

Yousif, N M K; Dawyndt, P; Abriouel, H; Wijaya, A; Schillinger, U; Vancanneyt, M; Swings, J; Dirar, H A; Holzapfel, W H; Franz, C M A P

2005-01-01

To identify enterococci from Hussuwa, a Sudanese fermented sorghum product, and determine their technological properties and safety for possible inclusion in a starter culture preparation. Twenty-two Enterococcus isolates from Hussuwa were identified as Enterococcus faecium by using phenotypic and genotypic tests such as 16S rDNA gene sequencing, RAPD-PCR and restriction fragment length polymorphism of the 16S/23S intergenic spacer region fingerprinting. Genotyping revealed that strains were not clonally related and exhibited a considerable degree of genomic diversity. Some strains possessed useful technological properties such as production of bacteriocins and H2O2 or utilization of raffinose and stachyose. None produced alpha-amylase or tannase. A safety investigation revealed that all strains were susceptible to the antibiotics ampicillin, gentamicin, chloramphenicol, tetracycline and streptomycin, but some were resistant to ciprofloxacin, erythromycin, penicillin and vancomycin. Production of biogenic amines or presence of genes encoding virulence determinants occurred in some strains. Enterococcus faecium strains are associated with fermentation of Sudanese Hussuwa. Some strains exhibited useful technological properties such as production of antimicrobial agents and fermentation of indigestible sugars, which may aid in stabilizing and improving the digestibility of the product respectively. Enterococci were shown to play a role in the fermentation of African foods. While beneficial properties of these bacteria are indicated, their presence in this food may also imply a hygienic risk as a result of antimicrobial resistances or presence of virulence determinants.

Study of the mechanical properties of the electric power station components: the punch test; Etude des proprietes mecaniques des composants de centrales thermiques: l'essai punch test

Energy Technology Data Exchange (ETDEWEB)

Isselin, J

2003-03-15

The aging of the electric production park implies an increasing need of knowledge concerning the evolution of the mechanical properties of its components. With regard to this problem, the availability in material is more and more small. This work proposes to characterize these properties through a mechanical test called Punch test. The main characteristic of this test is to use very small volume samples. The development of this test has been carried out by the study of a 15 MDV 4-05 steel coming from a steam drum of a thermal power plant after 145000 hours of service. At first, we have measured the influence of the parameters of this test. Then, the study has dealt more particularly on the transition temperature of the material. With the finite element simulation method, the strain hardening coefficient of the material has been determined. (O.M.)

Measurement of tensile and fracture toughness properties using small punch test

International Nuclear Information System (INIS)

Chatterjee, S.; Shah Priti Kotak

2005-05-01

Small punch test wu carried out at room temperature on five different steels using 10 mm by 10 mm specimens of 0.4 mm thickness in a univesal testing machine. The tensile and fracture toughness properties of the five steels obtained from small punch test were compared with those obtained from the standard test method. The results (except in one steel) show that the tensile properties obtained from small punch test are in close proximity to those obtained ftom uni-axial tension test. The results also show that fracture toughness (Jic) properties obtained ftom small punch test are within ±20% of the corresponding values obtained using standard test procedures. (author)

Mechanical and natural durability properties of wood treated with a novel organic preservative/consolidant product

International Nuclear Information System (INIS)

Lionetto, Francesca; Frigione, Mariaenrica

2009-01-01

An organic preservative/consolidant of new formulation was selected in order to evaluate its effect on the mechanical properties of worm-eaten walnut wood. Walnut wood is widely used for the realization of artistic handworks (e.g. statues, altars, etc.) furniture and flooring. The flexural strength and modulus of elasticity, the toughness and the hardness were determined on both treated and untreated samples. The experimental results showed that the product increased significantly the flexural strength while the other mechanical properties were not appreciably affected by the chemical treatment. The microstructure of the samples tested was observed using scanning electron microscopy. The preserving character against insects of the investigated product was assessed by both visual inspection and measurements of weight loss on the treated specimens after their exposure to living insects. The samples on which the product was applied, exposed to Oligomerus ptilinoides for one year, were more resistant to decay than the corresponding untreated samples.

Radiological testing of products containing radioactivity

International Nuclear Information System (INIS)

Dixon, D.W.; Knight, A.

1980-01-01

Consumer products containing radioactive substances are tested by NRPB to determine how much radioactive material is likely to be released from a product if it is misused or accidentally damaged. Such testing is briefly described with particular reference to ionisation chamber smoke detectors, liquid crystal display watches illuminated with gaseous tritium light sources and anti-static brushes containing polonium-210 in the form of ceramic microspheres. (U.K.)

46 CFR 57.06-4 - Production testing specimen requirements.

Science.gov (United States)

2010-10-01

... WELDING AND BRAZING Production Tests § 57.06-4 Production testing specimen requirements. (a) For test... 46 Shipping 2 2010-10-01 2010-10-01 false Production testing specimen requirements. 57.06-4... to welding shall not throw the finished test plate out of line by an angle of over 5°. (c) Where the...

Production and properties of micro-cellulose reinforced thermoplastic starch

Science.gov (United States)

Kmetty, Á.; Karger-Kocsis, J.; Czigány, T.

2015-02-01

Thermoplastic starch (TPS)/micro-fibrillated cellulose (MFC) composites were prepared from maize starch with different amount of distilled water, glycerol and cellulose reinforcement. The components were homogenized by kneader and twin roll technique. The produced TPS and TPS-based polymer composites were qualified by static and dynamic mechanical tests and their morphology was analysed by microscopic techniques. The results showed that the amount of water and the order of the production steps control the properties of both the TPS and its MFC reinforced version. With increasing content of MFC the stiffness and strength of the TPS matrix increased, as expected. Microscopic inspection revealed that the TPS has a homogenous structure and the MFC is well dispersed therein when suitable preparation conditions were selected.

Data on the chemical properties of commercial fish sauce products.

Science.gov (United States)

Nakano, Mitsutoshi; Sagane, Yoshimasa; Koizumi, Ryosuke; Nakazawa, Yozo; Yamazaki, Masao; Watanabe, Toshihiro; Takano, Katsumi; Sato, Hiroaki

2017-12-01

This data article reports on the chemical properties of commercial fish sauce products associated with the fish sauce taste and flavor. All products were analyzed in triplicate. Dried solid content was analyzed by moisture analyzer. Fish sauce salinity was determined by a salt meter. pH was measured using a pH meter. The acidity was determined using a titration assay. Amino nitrogen and total nitrogen were evaluated using a titration assay and Combustion-type nitrogen analyzer, respectively. The analyzed products originated from Japan, Thailand, Vietnam, China, the Philippines, and Italy. Data on the chemical properties of the products are provided in table format in the current article.

The effect of stimulated fission products on the structure and the mechanical properties of zircaloy

International Nuclear Information System (INIS)

Holub, F.

1982-01-01

The objective of investigation was to study the long-term effects of individual simulated fission products on the mechanical properties and the structure of Zircaloy. Tensile Test specimens of Zircaloy were annealed with important simulated fission products at 350 0 C up to 10,000 hours and at higher temperatures (500, 700 0 C) up to 2,000 hours. The principal methods of investigation on annealed Zircaloy specimens were tension tests at room temperature and at 400 0 C, scanning electron microscopy and microprobe technique, X-ray diffraction, X-ray fluorescence, optical metallography. The action of fission products at normal temperatures of reactor operation will give rise to a small enhancement of strength and a small drop of ductility of the fuel cladding material only. At high fuel pin temperatures which may be realized under abnormal operation conditions, some of the fission products potentially will produce detrimental consequences on the integrity of fuel pins. The most effective fission products will be: lanthanum oxide, followed by the earth alkaline oxides and the other rare earth oxides, molybdenum, iodine and cadmium

Topographic modelling of haptic properties of tissue products

International Nuclear Information System (INIS)

Rosen, B-G; Fall, A; Farbrot, A; Bergström, P; Rosen, S

2014-01-01

The way a product or material feels when touched, haptics, has been shown to be a property that plays an important role when consumers determine the quality of products For tissue products in constant touch with the skin, ''softness'' becomes a primary quality parameter. In the present work, the relationship between topography and the feeling of the surface has been investigated for commercial tissues with varying degree of texture from the low textured crepe tissue to the highly textured embossed- and air-dried tissue products. A trained sensory panel at was used to grade perceived haptic ''roughness''. The technique used to characterize the topography was Digital light projection (DLP) technique, By the use of multivariate statistics, strong correlations between perceived roughness and topography were found with predictability of above 90 percent even though highly textured products were included. Characterization was made using areal ISO 25178-2 topography parameters in combination with non-contacting topography measurement. The best prediction ability was obtained when combining haptic properties with the topography parameters auto-correlation length (Sal), peak material volume (Vmp), core roughness depth (Sk) and the maximum height of the surface (Sz)

Functional properties and sensory testing of whey protein concentrate sweetened with rebaudioside A

Directory of Open Access Journals (Sweden)

Paula Gimenez MILANI

2016-02-01

Full Text Available ABSTRACT Objective: To develop a natural dietary product with functional benefits for diabetic patients. Whey protein concentrate was obtained through the separation membrane processes and sweetened with rebaudioside A. This product was submitted to sensory testing in humans and used to evaluate possible functional properties in male Wistar rats models with diabetesMellitus induced by streptozotocin. Methods: Two concentrates were produced. Only the second showed protein content of 74.3 and 17.3% of lactose was used as supplementation in induced diabetic rats. This concentrate was obtained from the concentration by reverse osmosis system (180 k Daltons, followed by nanofiltration in a 500 k Daltons membrane and spray drying at 5.0% solution of the first concentrate developed. The concentrate was sweetened with rebaudioside A (rebaudioside A 26 mg/100 g concentrate. All procedures were performed at the Center for Studies in Natural Products, at the Universidade Estadual de Maringá. Three experimental groups were established (n=6: two groups of diabetic animals, one control group and one supplemented group; and a control group of normal mice (non-diabetic. The supplemented group received concentrates sweetened with rebaudioside A in a dose of 100 mg/kg bw/day by an esophageal tube for 35 days. Fasting, the fed state and body weight were assessed weekly for all groups. At the end of the supplementation period, the following were analyzed: plasma parameters of glucose, total cholesterol, triglycerides and fructosamine; the serum levels of aspartate aminotransferase and alanine aminotransferase, water and food intake. Organs and tissues were removed and weighed to assess mass and anatomical changes. Results: The product presented 74% of proteins and 17% of lactose and showed satisfactory sensory testing by the addition of 26 mg of rebaudioside A/100 g concentrate. Supplementation of the product reduced hyperglycemia, plasma fructosamine levels

Study of the mechanical properties of the electric power station components: the punch test; Etude des proprietes mecaniques des composants de centrales thermiques: l'essai punch test

Energy Technology Data Exchange (ETDEWEB)

Isselin, J

2003-03-15

The aging of the electric production park implies an increasing need of knowledge concerning the evolution of the mechanical properties of its components. With regard to this problem, the availability in material is more and more small. This work proposes to characterize these properties through a mechanical test called Punch test. The main characteristic of this test is to use very small volume samples. The development of this test has been carried out by the study of a 15 MDV 4-05 steel coming from a steam drum of a thermal power plant after 145000 hours of service. At first, we have measured the influence of the parameters of this test. Then, the study has dealt more particularly on the transition temperature of the material. With the finite element simulation method, the strain hardening coefficient of the material has been determined. (O.M.)

Analysis of anaerobic product properties in fluid and aggressive environments

OpenAIRE

Goncharov, A.; Tulinov, A.

2008-01-01

The article presents the results of experiments involved in investigation of properties of some domestic and foreign-made anaerobic materials in components and units operating in fluid and aggressive environments. These experiments determined the strength and swell values of anaerobic products in the sea water, fuel and oil, and confirmed their anticorrosion properties. The experiments demonstrated high resistance of anaerobic products to various fluids and aggressive environments, which make...

Property Testing on Linked Lists

DEFF Research Database (Denmark)

Afshani, Peyman; Matulef, Kevin; Wilkinson, Bryan Thomas

2013-01-01

We define a new property testing model for algorithms that do not have arbitrary query access to the input, but must instead traverse it in a manner that respects the underlying data structure in which it is stored. In particular, we consider the case when the underlying data structure is a linked...... list, and the testing algorithm is allowed to either sample randomly from the list, or walk to nodes that are adjacent to those already visited. We study the well-known monotonicity testing problem in this model, and show that (n13) queries are both necessary and sufficient to distinguish whether...... a list is sorted (monotone increasing) versus a constant distance from sorted. Our bound is strictly greater than the (logn) queries required in the standard testing model, that allows element access indexed by rank, and strictly less than the (n12) queries required by a weak model that only allows...

Heap-leaching of low-grade uranium ore at SOMAIR: from laboratory tests to production of 700 tonnes U per year

Energy Technology Data Exchange (ETDEWEB)

Durupt, N.; Blanvillain, J.J., E-mail: nicolas.durupt@areva.com [AREVA NC, Service d' Etudes de Procedes et d' Analyses (SEPA), Bessines sur Gartempe (France)

2010-07-01

In 2006, SOMAIR decided to increase the uranium production by 50% using heap leaching for the treatment of low grade ores. These ores, which come from different ores with various properties, have been studied in four steps: Lab tests: to compare the ores (characterization, acid consumptions, recovery); Column tests on an average sample: to define significant parameters for a feasibility study; Column tests on specific samples: to optimize recovery for each ore and identify problems of percolation due to the clays; and, Pilot tests in large boxes (stalls): to validate process parameters. Uranium production by heap leaching started commercially in July 2009. (author)

Impact of petroleum products on soil composition and physical-chemical properties

Science.gov (United States)

Brakorenko, N. N.; Korotchenko, T. V.

2016-03-01

The article describes the grain-size distribution, physical and mechanical properties, swelling and specific electrical resistivity of soils before and after the contact with petroleum products. The changes in mechanical properties of soils contaminated with petroleum products have been stated. It leads to the increase in compressibility values, decline in internal friction angle and cohesion.

Impact of petroleum products on soil composition and physical-chemical properties

OpenAIRE

Brakorenko, Nataliya Nikolaevna; Korotchenko, Tatiana Valerievna

2016-01-01

The article describes the grain-size distribution, physical and mechanical properties, swelling and specific electrical resistivity of soils before and after the contact with petroleum products. The changes in mechanical properties of soils contaminated with petroleum products have been stated. It leads to the increase in compressibility values, decline in internal friction angle and cohesion.

L2 Writing in Test and Non-test Situations: Process and Product

Directory of Open Access Journals (Sweden)

Baraa Khuder

2015-02-01

Full Text Available Test writers sometimes complain they cannot perform to their true abilities because of time constraints. We therefore examined differences in terms of process and product between texts produced under test and non-test conditions. Ten L2 postgraduates wrote two argumentative essays, one under test conditions, with only forty minutes being allowed and without recourse to resources, and one under non-test conditions, with unlimited time as well as access to the Internet. Keystroke logging, screen capture software, and stimulated recall protocols were used, participants explaining and commenting on their writing processes. Sixteen writing process types were identified. Higher proportions of the processes of translation and surface revision were recorded in the test situation, while meaningful revision and evaluation were both higher in the non-test situation. There was a statistically significant difference between time allocation for different processes at different stages. Experienced teachers awarded the non-test texts a mean score of almost one point (0.8 higher. A correlational analysis examining the relationship between writing process and product quality showed that while the distribution of writing processes can have an impact on text quality in the test situation, it had no effect on the product in the non-test situation.

Top quark pair production and top quark properties at CDF

Energy Technology Data Exchange (ETDEWEB)

Moon, Chang-Seong [INFN, Pisa

2016-06-02

We present the most recent measurements of top quark pairs production and top quark properties in proton-antiproton collisions with center-of-mass energy of 1.96 TeV using CDF II detector at the Tevatron. The combination of top pair production cross section measurements and the direct measurement of top quark width are reported. The test of Standard Model predictions for top quark decaying into $b$-quarks, performed by measuring the ratio $R$ between the top quark branching fraction to $b$-quark and the branching fraction to any type of down quark is shown. The extraction of the CKM matrix element $|V_{tb}|$ from the ratio $R$ is discussed. We also present the latest measurements on the forward-backward asymmetry ($A_{FB}$) in top anti-top quark production. With the full CDF Run II data set, the measurements are performed in top anti-top decaying to final states that contain one or two charged leptons (electrons or muons). In addition, we combine the results of the leptonic forward-backward asymmetry in $t\\bar t$ system between the two final states. All the results show deviations from the next-to-leading order (NLO) standard model (SM) calculation.

A test trial irradiation of natural rubber latex on large scale for the production of examination gloves in a production scale

International Nuclear Information System (INIS)

Devendra, R.; Kulatunge, S.; Chandralal, H.N.K.K.; Kalyani, N.M.V.; Seneviratne, J.; Wellage, S.

1996-01-01

Radiation Vulcanization of natural rubber latex has been developed extensively through various research and development programme. During these investigations many data was collected and from these data it was proved that radiation vulcanized natural rubber latex (RVNRL) can be used as a new material for industry (RVNRL symposium 1989; Makuuchi IAEA report). This material has been extensively tested in making of dipped goods and extruded products. However these investigations were confined only to laboratory experiments and these experiments mainly reflected material properties of RVNRL and only a little was observed about its behavior in actual production scale operation. The present exercise was carried out mainly to study the behavior of the material in production scale by irradiating latex on a large scale and producing gloves in a production scale plant. It was found that RVNRL can be used in conventional glove plants without making major alteration to the plant. Quality of the gloves that were produced using RVNRL is acceptable. It was also found that the small deviation of vulcanization dose will affect the crosslinking density of films. This will drastically reduce the tensile strength of the film. Crosslinking density or pre-vulcanized relax modulus (PRM) at 100% is a reliable property to control the pre vulcanization of latex by radiation

Optical And Environmental Properties Of NCAP Glazing Products

Science.gov (United States)

van Konynenburg, Peter; Wipfler, Richard T.; Smith, Jerry L.

1989-07-01

The first large area, commercially available, electrically-controllable glazing products sold under the tradename VARILITETM are based on a new liquid crystal film technology called NCAP. The glazing products can be switched in milliseconds between a highly translucent state (for privacy and glare control) to a transparent state (for high visibility) with the application of an AC voltage. The optical and environmental properties are demonstrated to meet the general requirements for architectural glazing use. The first qualified indoor product is described in detail.

The Effect of Moisture Content of Maize Grits on Physicochemical Properties of Its Puffed Food Products Properties of Its Puffed Food Products

Directory of Open Access Journals (Sweden)

S. Sharifi

2016-02-01

Full Text Available In this study the effect of different levels of moisture content of maize grits (10, 13, 16 and 19% as an attribute of physicochemical properties of extruder-derived puffed products, was investigated. The results showed that with increasing maize grits' moisture content, water absorption index (WAI and water solubility index (WSI were decreased. Moreover, with changing in feed moisture content from 10 to 16%, the volume and sectional expansion index (SEI increased but further increase of moisture content to 19% caused a reduction in these parameters. The textural tests also revealed that with increase in moisture content, the compression energy (Nmm, maximum force (N and time to achieve the first major peak (s were increased but the number of peaks was decreased. With increase in the moisture content, specific mechanical energy (SME was decreased, due probably to the reduction in the viscosity of melt. With increase in the moisture content the L and b values were increased but the value of the samples were decreased due to the reduction of Maillard reaction rate. Our data confirms that the moisture content of maize grits may play an important role in the quality of produced extruded snacks and a high quality product can be achieved by optimizing this parameter. In this research, the maximum volume of the extruder product was obtained in 16% of moisture level.

A smart predictor for material property testing

International Nuclear Information System (INIS)

Wang, Wilson; Kanneg, Derek

2008-01-01

A reliable predictor is very useful for real-world industrial applications to forecast the future behavior of dynamic systems. A smart predictor, based on a novel recurrent neural fuzzy (RNF) scheme, is developed in this paper for multi-step-ahead prediction of material properties. A systematic investigation based on two benchmark data sets is conducted in terms of performance and efficiency. Analysis results reveal that, of the data-driven forecasting schemes, predictors based on step input patterns outperform those based on sequential input patterns; the RNF predictor outperforms those based on recurrent neural networks and ANFIS schemes in multi-step-ahead prediction of nonlinear time series. An adaptive Levenberg–Marquardt training technique is adopted to improve the robustness and convergence of the RNF predictor. Furthermore, the proposed smart predictor is implemented for material property testing. Investigation results show that the developed RNF predictor is a reliable forecasting tool for material property testing; it can capture and track the system's dynamic characteristics quickly and accurately. It is also a robust predictor to accommodate different system conditions

PROPERTIES OF DENIZLI VOLCANICS AND POTENTIAL USING FOR CONCRETE PRODUCTION

Directory of Open Access Journals (Sweden)

Barış SEMİZ

2005-01-01

Full Text Available In this study, mineralogical, petrographical and chemical properties of volcanic rocks (Denizli Volcanics with basaltic trachyandesite composition which are located in southern of Denizli province have been investigated. Their physical and mechanical tests have been carried out on the samples to find out their performance both as an aggregate in concrete and as building stone in the construction sector. Unit weights, water absorption, porosity and uniaxial compressive strength of the tested samples are between 2250-2960 kg/m3, % 0.06-0.4, % 0.15-10.22 and 52.4-170.2 MPa, respectively. Average 28-day compressive strengths of the concrete are 94.44 MPa and the results fit the mineralogical and petrographical characteristics. There is a total of 2750 million ton probable reserve and it is an alternative aggregate to limestone which has already been produced in the region. High strength concrete production is vital for high quality construction especially in earthquake zones.

Test Marketing in New Product Development

Science.gov (United States)

Klompmaker, Jay E.; And Others

1976-01-01

Discusses the role of test marketing in new product development, based on interviews with marketing executives. Attempts to clarify when a test market should be done, what its aims should be, and how it should be used. (JG)

Thermal property testing technique on micro specimen

International Nuclear Information System (INIS)

Baba, Tetsuya; Kishimoto, Isao; Taketoshi, Naoyuki

2000-01-01

This study aims at establishment of further development on some testing techniques on the nuclear advanced basic research accumulated by the National Research Laboratory of Metrology for ten years. For this purpose, a technology to test heat diffusion ratio and specific heat capacity of less than 3 mm in diameter and 1 mm in thickness of micro specimen and technology to test heat diffusion ratio at micro area of less than 1 mm in area along cross section of less than 10 mm in diameter of column specimen were developed to contribute to common basic technology supporting the nuclear power field. As a result, as an element technology to test heat diffusion ratio and specific heat capacity of the micro specimen, a specimen holding technique stably to hold a micro specimen with 3 mm in diameter could be developed. And, for testing the specific heat capacity by using the laser flush differential calorimetry, a technique to hold two specimen of 5 mm in diameter at their proximities was also developed. In addition, by promoting development of thermal property data base capable of storing thermal property data obtained in this study and with excellent workability in this 1998 fiscal year a data in/out-put program with graphical user interface could be prepared. (G.K.)

Microbial lipases: Production, properties and biotechnological applications

Directory of Open Access Journals (Sweden)

Josana Maria Messias

2011-09-01

Full Text Available Lipases belong to the group of hydrolases that catalyze the hydrolysis of triacylglycerol lipids to free fatty acids and glycerol. They have significant potential biotechnological applications in catalyzing organic synthesis reactions in non-aqueous solvents using simplified procedures resulting in conversions of high yields. Lipase production has conventionally been performed by submerged fermentation; however, solid-state fermentation processes have been prominent when residues are used as substrates because they serve as low-cost nutrient sources. Microbial lipases can be used as additives in foods to modify and enhance organoleptic properties, as well as in detergents to hydrolyse fats in the treatment of oily effluents, and also have value for pharmaceutical, cosmetic, agrochemical, and oil chemical industries. More recently, they are used in transesterification reactions to convert plant seed oils into biodiesel. The objective of this work was to review the published literature on the production, properties and applications of microbial lipases, and its biotechnological role in producing biodiesel.

A systematic review investigating measurement properties of physiological tests in rugby.

Science.gov (United States)

Chiwaridzo, Matthew; Oorschot, Sander; Dambi, Jermaine M; Ferguson, Gillian D; Bonney, Emmanuel; Mudawarima, Tapfuma; Tadyanemhandu, Cathrine; Smits-Engelsman, Bouwien C M

2017-01-01

This systematic review was conducted with the first objective aimed at providing an overview of the physiological characteristics commonly evaluated in rugby and the corresponding tests used to measure each construct. Secondly, the measurement properties of all identified tests per physiological construct were evaluated with the ultimate purpose of identifying tests with strongest level of evidence per construct. The review was conducted in two stages. In all stages, electronic databases of EBSCOhost, Medline and Scopus were searched for full-text articles. Stage 1 included studies examining physiological characteristics in rugby. Stage 2 included studies evaluating measurement properties of all tests identified in Stage 1 either in rugby or related sports such as Australian Rules football and Soccer. Two independent reviewers screened relevant articles from titles and abstracts for both stages. Seventy studies met the inclusion criteria for Stage 1. The studies described 63 tests assessing speed (8), agility/change of direction speed (7), upper-body muscular endurance (8), upper-body muscular power (6), upper-body muscular strength (5), anaerobic endurance (4), maximal aerobic power (4), lower-body muscular power (3), prolonged high-intensity intermittent running ability/endurance (5), lower-body muscular strength (5), repeated high-intensity exercise performance (3), repeated-sprint ability (2), repeated-effort ability (1), maximal aerobic speed (1) and abdominal endurance (1). Stage 2 identified 20 studies describing measurement properties of 21 different tests. Only moderate evidence was found for the reliability of the 30-15 Intermittent Fitness. There was limited evidence found for the reliability and/or validity of 5 m, 10 m, 20 m speed tests, 505 test, modified 505 test, L run test, Sergeant Jump test and bench press repetitions-to-fatigue tests. There was no information from high-quality studies on the measurement properties of all the other tests

Computational chemical product design problems under property uncertainties

DEFF Research Database (Denmark)

Frutiger, Jerome; Cignitti, Stefano; Abildskov, Jens

2017-01-01

Three different strategies of how to combine computational chemical product design with Monte Carlo based methods for uncertainty analysis of chemical properties are outlined. One method consists of a computer-aided molecular design (CAMD) solution and a post-processing property uncertainty...... fluid design. While the higher end of the uncertainty range of the process model output is similar for the best performing fluids, the lower end of the uncertainty range differs largely....

Moisture performance properties of exterior sheathing products made of spruce plywood or OSB

Energy Technology Data Exchange (ETDEWEB)

Ojanen, T.; Ahonen, J. [VTT Building and Transport, Espoo (Finland)

2005-02-01

Plywood and OSB (Oriented Strand Board) are building boards that are made of timber and glue and that have good structural strength. OSB is a relatively new product that is produced from various timber materials and even some wastewood can be used as raw material for this product. Due to the easy access of raw material and economical reasons, the use of OSB has been highly increasing. The moisture safety of the building envelope depends on the properties of the building products. The moisture performance properties of the sheathing boards have not got enough attention, too often these wood based materials are equated without considering the real properties and their effect on the overall moisture performance. This research was carried out to experimentally determine the material properties and performance characteristics that have an effect on the moisture performance of building structures where OSB or spruce plywood are applied as exterior sheathing boards. A relatively representative amount of samples were used to study the moisture properties of European OSB and plywood products and a comparison to one Canadian OSB and one plywood product was done. All the products used in this research were meant to be used also as exterior sheathing boards. The results shows clearly the differences between OSB and plywood products. The products are not interchangeable. The main differences can be found from the vapour permeability levels that have an effect on the drying efficiency of building structures. The products have different performance criteria, and the climate conditions and moisture loads have to be studied to evaluate their suitability and moisture safety aspects in different applications. Water repellent features and drying efficiency are somewhat opposite properties of the products and the dimensional changes under varying moisture contents can set some boundary conditions when the optimum solution for the exterior sheathing is considered. (orig.)

Effect of by-product steel slag on the engineering properties of clay soils

Directory of Open Access Journals (Sweden)

Faisal I. Shalabi

2017-10-01

Full Text Available Clay soils, mainly if they contain swelling minerals such as smectite or illite, may cause severe damage to structures, especially when these soils are subjected to wetting and drying conditions. High expansion and reduction in shear strength and foundation bearing capacity will take place due to the increase in water content of these soils. The engineering properties of these kinds of soils can be improved by using additives and chemical stabilizers. In this work, by-product steel slag was used to improve the engineering properties of clay soils. Lab and field experimental programs were developed to investigate the effect of adding different percentages of steel slag on plasticity, swelling, compressibility, shear strength, compaction, and California bearing ratio (CBR of the treated materials. The results of tests on the clay soil showed that as steel slag content increased, the soil dry density, plasticity, swelling potential, and cohesion intercept decreased and the angle of internal friction increased. For the CBR, the results of the tests showed an increase in the CBR value with the increase in slag content.

CMOS-MEMS Test-Key for Extracting Wafer-Level Mechanical Properties

Directory of Open Access Journals (Sweden)

Pei-Zen Chang

2012-12-01

Full Text Available This paper develops the technologies of mechanical characterization of CMOS-MEMS devices, and presents a robust algorithm for extracting mechanical properties, such as Young’s modulus, and mean stress, through the external electrical circuit behavior of the micro test-key. An approximate analytical solution for the pull-in voltage of bridge-type test-key subjected to electrostatic load and initial stress is derived based on Euler’s beam model and the minimum energy method. Then one can use the aforesaid closed form solution of the pull-in voltage to extract the Young’s modulus and mean stress of the test structures. The test cases include the test-key fabricated by a TSMC 0.18 μm standard CMOS process, and the experimental results refer to Osterberg’s work on the pull-in voltage of single crystal silicone microbridges. The extracted material properties calculated by the present algorithm are valid. Besides, this paper also analyzes the robustness of this algorithm regarding the dimension effects of test-keys. This mechanical properties extracting method is expected to be applicable to the wafer-level testing in micro-device manufacture and compatible with the wafer-level testing in IC industry since the test process is non-destructive.

Processed tomato products as a source of dietary lycopene: bioavailability and antioxidant properties.

Science.gov (United States)

Rao, A Venket

2004-01-01

Oxidative stress is one of the major contributors to increased risk of chronic diseases. A diet rich in tomatoes and tomato products containing lycopene, a carotenoid antioxidant, has been found to protect against these chronic diseases by mitigating oxidative damage. The study aim was to evaluate the effects of a long-term tomato-rich diet, consisting of various processed tomato products, on bioavailability and antioxidant properties of lycopene. Seventeen healthy human subjects (ten men, seven non-pregnant women) participated in the study. Following a two-week washout period during which subjects avoided foods containing lycopene, all subjects consumed test tomato products including tomato juice, tomato sauce, tomato paste, ketchup, spaghetti sauce, and ready-to-serve tomato soup providing 30 mg of lycopene a day for four weeks. At the end of treatment, serum lycopene level increased significantly (p reduced significantly (p can increase serum lycopene levels and reduce oxidative stress effectively.

Thermomechanical and adhesive properties of radiation-modified polymer composites for thermosetting products

International Nuclear Information System (INIS)

Kalkis, V.; Maksimov, R.D.; Kalnins, M.; Zicans, J.; Bocoka, T.; Revjakin, O.

2000-01-01

The gamma-irradiated blends of polyethylene (PE) with ethylene / propylene / diene copolymer (Epdm) and thermotropic liquid crystalline polymer (LCP) are investigated. The radiation dose absorbed does not exceed 150 kGy (10 kGy=1 Mrad). It is shown that the even small amounts of LCP added to PE improve the mechanical and operational properties of composites and the thermosetting products made of them. The temperature dependences of the elastics modulus, tension diagrams at a temperature above the PE melting point, and recovery curves of the oriented specimens are presented. The kinetics of thermorelaxation and residual setting stresses upon isometric heating and cooling of the previously oriented composites is studied. The data on the influence of LCP on the adhesion interaction of the blend with steel are obtained. The features of thermomechanical and adhesive properties are discussed and the results of morphological and calorimetric tests are given. (author)

Slags from steel production: Properties and their utilization

Directory of Open Access Journals (Sweden)

J. Vlcek

2013-07-01

Full Text Available During steel production a considerable amount of slags is produced. In addition to its usual processing, as recycling in device for steel production and preparation of aggregates, it is also possible to apply less common slag processing ways. Depending on cooling mode of the steel slags these may show some binding properties. Geopolymer type binders can be prepared from the slag using alkali activators or the hydraulic properties of the dicalciumsilicate present in the slag can be induced by water. The paper summarizes present state of material utilisation of the steel slags with focus on emphasize of the possible sources of the slag volume instability. The influence of process of slag cooling on its phase composition is documented. It was also found that slags from real sources show different parameters compared to samples obtained for laboratory examination.

Protocol for production of a chewable material for masticatory function tests (Optocal - Brazilian version

Directory of Open Access Journals (Sweden)

Rafael de Liz Pocztaruk

2008-12-01

Full Text Available The present article aimed to present a standardized protocol for the production of a chewable test material that has been used in masticatory efficiency and performance studies. This chewable material has advantages in respect to its physical properties when compared to other artificial and natural test foods. It is constituted by mixing condensation silicon (58.3% by weight, common plaster (10.2% by weight, alginate (12.5% by weight, solid vaseline (11.5% by weight, tooth paste (7.5% by weight, and catalyst paste (20.8 mg/g, adding also three drops of mint essence. The mixed material is then inserted into an acrylic mould with perforations of 12 mm in diameter and 5 mm in height to produce rounded tablets with those measures after polymerization. It was named "Optocal - Brazilian version". A volume of 3 cm³ is indicated for a chewing test, which corresponds to 12 tablets using the present methodology. The present protocol can make the production of this chewable material easier, helping in its standardization for studies on masticatory function.

Relevance of microbial finished product testing in food safety management

DEFF Research Database (Denmark)

Zwietering, Marcel H.; Jacxsens, Liesbeth; Membré, Jeanne Marie

2016-01-01

Management of microbiological food safety is largely based on good design of processes, products and procedures. Finished product testing may be considered as a control measure at the end of the production process. However, testing gives only very limited information on the safety status of a food......-active way by implementing an effective food safety management system. For verification activities in a food safety management system, finished product testing may however be useful. For three cases studies; canned food, chocolate and cooked ham, the relevance of testing both of finished products....... If a hazardous organism is found it means something, but absence in a limited number of samples is no guarantee of safety of a whole production batch. Finished product testing is often too little and too late. Therefore most attention should be focussed on management and control of the hazards in a more pro...

Gluconic Acid: Properties, Applications and Microbial Production

Directory of Open Access Journals (Sweden)

Sumitra Ramachandran

2006-01-01

Full Text Available Gluconic acid is a mild organic acid derived from glucose by a simple oxidation reaction. The reaction is facilitated by the enzyme glucose oxidase (fungi and glucose dehydrogenase (bacteria such as Gluconobacter. Microbial production of gluconic acid is the preferred method and it dates back to several decades. The most studied and widely used fermentation process involves the fungus Aspergillus niger. Gluconic acid and its derivatives, the principal being sodium gluconate, have wide applications in food and pharmaceutical industry. This article gives a review of microbial gluconic acid production, its properties and applications.

Production and properties towards the island of stability

International Nuclear Information System (INIS)

Leino, Matti

2016-01-01

The structure of the nuclei of the heaviest elements is discussed with emphasis on single-particle properties as determined by decay and in-beam spectroscopy. The basic features of production of these nuclei using fusion evaporation reactions will also be discussed.

Ultrasound-based testing of tendon mechanical properties

DEFF Research Database (Denmark)

Seynnes, O R; Bojsen-Møller, J.; Albracht, K

2015-01-01

In the past 20 years, the use of ultrasound-based methods has become a standard approach to measure tendon mechanical properties in vivo. Yet the multitude of methodological approaches adopted by various research groups probably contribute to the large variability of reported values. The technique......, or signal synchronization; and 2) in physiological considerations related to the viscoelastic behavior or length measurements of tendons. Hence, the purpose of the present review is to assess and discuss the physiological and technical aspects connected to in vivo testing of tendon mechanical properties...

Comments on Thermal Physical Properties Testing Methods of Phase Change Materials

Directory of Open Access Journals (Sweden)

Jingchao Xie

2013-01-01

Full Text Available There is no standard testing method of the thermal physical properties of phase change materials (PCM. This paper has shown advancements in this field. Developments and achievements in thermal physical properties testing methods of PCM were commented, including differential scanning calorimetry, T-history measurement, the water bath method, and differential thermal analysis. Testing principles, advantages and disadvantages, and important points for attention of each method were discussed. A foundation for standardized testing methods for PCM was made.

Optimal number of tests to achieve and validate product reliability

International Nuclear Information System (INIS)

Ahmed, Hussam; Chateauneuf, Alaa

2014-01-01

The reliability validation of engineering products and systems is mandatory for choosing the best cost-effective design among a series of alternatives. Decisions at early design stages have a large effect on the overall life cycle performance and cost of products. In this paper, an optimization-based formulation is proposed by coupling the costs of product design and validation testing, in order to ensure the product reliability with the minimum number of tests. This formulation addresses the question about the number of tests to be specified through reliability demonstration necessary to validate the product under appropriate confidence level. The proposed formulation takes into account the product cost, the failure cost and the testing cost. The optimization problem can be considered as a decision making system according to the hierarchy of structural reliability measures. The numerical examples show the interest of coupling design and testing parameters. - Highlights: • Coupled formulation for design and testing costs, with lifetime degradation. • Cost-effective testing optimization to achieve reliability target. • Solution procedure for nested aleatoric and epistemic variable spaces

Property Outlaws in Cyberspace and Meatspace? Examining the Relationship between Online Peer Production and Support for Private Property Violations

Directory of Open Access Journals (Sweden)

Timothy Gibson

2014-11-01

Full Text Available Marxian theory has long viewed the institution of private property as central to labour exploitation. After all, private property laws allow those who control the means of production to expropriate surplus value from the dispossessed. An analogous relationship arguably defines life on the Internet, where users are forced to venture onto privately owned digital enclosures to access key services. Yet these online property relationships are anything but settled and uncontested. Outside the digital enclosures of Apple and Google, the Internet has fostered the development of “commons-based peer production”, where key resources (e.g. software are produced without anyone claiming exclusive property rights. In fact, some scholars have argued that the rise of peer production on the web has begun to re-shape popular attitudes concerning the legitimacy of property exclusions more broadly. In short, as we become “property outlaws” on the web, we come to question the inevitability and legitimacy of private property elsewhere in life. This paper explores this hypothesis by reporting data from a survey of Internet users at an East Coast university. Are users who engage in more peer production activities on the web also more likely to approve of “property outlaw” behaviours not just in the online context, but in the offline world as well (e.g. squatting? The data provide only partial support for the hypothesis: active online peer producers were indeed more likely to support violations of intangible (intellectual properties, but not violations of tangible or “real-world” properties.

46 CFR 57.06-3 - Method of performing production testing.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Method of performing production testing. 57.06-3 Section 57.06-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING WELDING AND BRAZING Production Tests § 57.06-3 Method of performing production testing. (a) Except as...

Electromagnetic NDT to characterize usage properties of flat steel products

Energy Technology Data Exchange (ETDEWEB)

Altpeter, I.; Dobmann, G.; Szielasko, K., E-mail: iab.altlau@t-online.de, E-mail: gerd.dobmann@t-online.de, E-mail: klaus.szielasko@izfp.fraunhofer.de [Fraunhofer Inst. - IZFP, Saarbruecken (Germany)

2015-07-15

The Fraunhofer Institute for Non-destructive Testing (IZFP) in Saarbruecken, Germany, started its activities in materials characterization of flat steel products in the eighties of the last century in the basic program of the European Community of Coal and Steel (ECCS). Throughout the years, continuous research and development were performed. The objective of the work, presented within this three-part series of reports, is to discuss the history of an innovation which began in 1988 with R&D in the area of texture characterization in steel sheets produced for car-body manufacturing (Part 1). In the following years the activities were to automate online property determination in terms of yield strength, tensile strength, planar, and vertical-anisotropy-factors. Again, steel sheets were the focus of the developments and the first NDT systems that came into industrial application for this project. Parallel research was performed to characterize the mechanical properties and hardness of heavy steel plates, mainly produced for pipeline manufacturing and off-shore applications (Part 2) The final report in the series (Part 3) will discuss steel sheet characterization and presents the successful development of a combination-transducer which combines ultrasonics with electromagnetic NDT. (author)

Electromagnetic NDT to characterize usage properties of flat steel products

International Nuclear Information System (INIS)

Altpeter, I.; Dobmann, G.; Szielasko, K.

2015-01-01

The Fraunhofer Institute for Non-destructive Testing (IZFP) in Saarbruecken, Germany, started its activities in materials characterization of flat steel products in the eighties of the last century in the basic program of the European Community of Coal and Steel (ECCS). Throughout the years, continuous research and development were performed. The objective of the work, presented within this three-part series of reports, is to discuss the history of an innovation which began in 1988 with R&D in the area of texture characterization in steel sheets produced for car-body manufacturing (Part 1). In the following years the activities were to automate online property determination in terms of yield strength, tensile strength, planar, and vertical-anisotropy-factors. Again, steel sheets were the focus of the developments and the first NDT systems that came into industrial application for this project. Parallel research was performed to characterize the mechanical properties and hardness of heavy steel plates, mainly produced for pipeline manufacturing and off-shore applications (Part 2) The final report in the series (Part 3) will discuss steel sheet characterization and presents the successful development of a combination-transducer which combines ultrasonics with electromagnetic NDT. (author)

Compost amendment of sandy soil affects soil properties and greenhouse tomato productivity

DEFF Research Database (Denmark)

Arthur, Emmanuel; Cornelis, W.; Razzaghi, Fatemeh

2012-01-01

Sandy soils, with low productivity, could be improved by compost application to sustain crop production. This study aimed to examine the effect of three compost types (vegetable, fruit and yard waste compost, garden waste compost, and spent mushroom compost) on basic properties of a loamy sand...... compost had greater effect in improving tomato productivity. A decade-long application of composts on loamy sand improved basic chemical and physical properties which were reflected in increased fruit yield in tomato. Since no negative effect of compost was observed, we suggest that sandy soils may serve...... and greenhouse tomato productivity. Disturbed and intact soil samples were taken from a decade-long compost field experiment on loamy sand with three compost types at application rate of 30 m3 ha-1 yr-1 (7.5 ton ha-1 yr-1). The soils were characterized for chemical and physical properties. Tomato was planted...

Mechanical properties used for the qualification of transport casks

International Nuclear Information System (INIS)

Salzbrenner, R.; Crenshaw, T.B.; Sorenson, K.B.

1993-01-01

The qualification process that should be sufficient for qualification of a specific cask (material/geometry combination) has been examined. The prototype cask should be tested to determine its overall variation in microstructure, chemistry, and mechanical properties. This prototype may also be subjected to 'proof testing' to demonstrate the validity of the design analysis (including the mechanical properties used in the analysis). The complete mechanical property mapping does not necessarily have to precede the proof testing (i.e., portions of the cask which experience only low (elastic) loads during the drop test are suitable for mechanical test specimens). The behavior of the prototype cask and the production casks are linked by assuring that each cask possesses at least the minimum level of one or more critical mechanical properties. This may be done by measuring the properties of interest directly, or by relying on a secondary measurement (such as subsize mechanical test results or microstructure/compositional measurements) which has been statistically correlated to the critical properties. The database required to show the correlation between the secondary measurement and the valid design property may be established by tests on the material from the prototype cask. The production controls must be demonstrated as being adequate to assure that a uniform product is produced. The testing of coring (or test block or prolongation) samples can only be viewed as providing a valid link to the benchmark results provided by the prototype cask if the process used to create follow-on casks remains essentially similar. The MOSAIK Test Program has demonstrated the qualification method through the benchmarking stage. The program did not establish for qualifying serial production casks through, for example, a correlation between small specimen parameters and valid design fracture toughness properties. Such a correlation would require additional experimental work. (J.P.N.)

Determining the thermal and physicals properties of oil processing products

Directory of Open Access Journals (Sweden)

Viktoria I. Kryvda

2015-03-01

Full Text Available In the last decades both technological process’ improvement and primary energy resources saving are the main tasks of oil refineries. Using various oil products does impose an accurate knowledge of their properties. The dispersion analysis applied makes possible to construct a model simulating the primary oil refining products’ and raw materials’ thermal physical properties. As a result of data approximation there were obtained polynomials with coefficients differing from attributable to the studied oil products fractions. The research represents graphic dependences of thermal physical properties on temperature values for diesel oil fraction. The linear character of density and calorific capacity dependencies from temperature is represented with a proportional error in calculations. The relative minimum error is below 2% that confirms the implemented calculations’ adequacy. The resulting model can be used in calculations for further technological process improvements.

Production of environmentally friendly aerated concrete with required construction and operational properties

Directory of Open Access Journals (Sweden)

Tkach Evgeniya

2018-01-01

Full Text Available The purpose of these studies is to justify the feasibility of recycling different types of industrial waste instead of conventional expensive raw materials in production of environmentally friendly aerated concrete with required construction and operational properties. The impact of wastes from various industries on the environmental condition of affected areas, as well as the results of their environmental assessment were analyzed to determine whether these wastes could be used in production of high-performance building materials. The assessment of industrial wastes in aerated concrete production suggests that industrial wastes of hazard class IV can be recycled to produce aerated concrete. An environmentally friendly method for large-scale waste recycling, including a two-step environmentally sustainable mechanism, was developed. The basic quality indicators of the modified aerated concrete proved that the environmental safety could be enhanced by strengthening the structure, increasing its uniformity and improving thermal insulation properties. The modified non-autoclaved aerated concrete products with improved physical and operational properties were developed. They have the following properties: density – D700; class of concrete – B3.5; thermal transmittance coefficient – 0.143 W/(m·°C; frost resistance – F75.

Property Modelling for Applications in Chemical Product and Process Design

DEFF Research Database (Denmark)

Gani, Rafiqul

such as database, property model library, model parameter regression, and, property-model based product-process design will be presented. The database contains pure component and mixture data for a wide range of organic chemicals. The property models are based on the combined group contribution and atom...... is missing, the atom connectivity based model is employed to predict the missing group interaction. In this way, a wide application range of the property modeling tool is ensured. Based on the property models, targeted computer-aided techniques have been developed for design and analysis of organic chemicals......, polymers, mixtures as well as separation processes. The presentation will highlight the framework (ICAS software) for property modeling, the property models and issues such as prediction accuracy, flexibility, maintenance and updating of the database. Also, application issues related to the use of property...

Collider Dipole Magnet test program from development through production

International Nuclear Information System (INIS)

Bailey, R.E.

1991-01-01

Verification of CDM performance, reliability, and magnet production processes will be accomplished during the development phase of the program. Key features of this program include thorough in process testing of magnet subassemblies, verification of the magnetic field quality, and demonstration of the CDM performance during the formal qualification program. Reliability demonstration of the CDM design includes component tests and an accelerated life test program. Prototype magnet phase will address achievement of magnet performance goals through a program of fabrications, test, analysis, redesign as required and procurement of modified parts for a second fabrication run. This process would be repeated again if necessary, and would conclude with a final design for the production magnets. Production process validation will address the effects that key production processes have upon magnet performance, using the magnets produced during the Preproduction phase

Potential Errors and Test Assessment in Software Product Line Engineering

Directory of Open Access Journals (Sweden)

Hartmut Lackner

2015-04-01

Full Text Available Software product lines (SPL are a method for the development of variant-rich software systems. Compared to non-variable systems, testing SPLs is extensive due to an increasingly amount of possible products. Different approaches exist for testing SPLs, but there is less research for assessing the quality of these tests by means of error detection capability. Such test assessment is based on error injection into correct version of the system under test. However to our knowledge, potential errors in SPL engineering have never been systematically identified before. This article presents an overview over existing paradigms for specifying software product lines and the errors that can occur during the respective specification processes. For assessment of test quality, we leverage mutation testing techniques to SPL engineering and implement the identified errors as mutation operators. This allows us to run existing tests against defective products for the purpose of test assessment. From the results, we draw conclusions about the error-proneness of the surveyed SPL design paradigms and how quality of SPL tests can be improved.

Optimization and Improvement of Test Processes on a Production Line

Science.gov (United States)

Sujová, Erika; Čierna, Helena

2018-06-01

The paper deals with increasing processes efficiency at a production line of cylinder heads of engines in a production company operating in the automotive industry. The goal is to achieve improvement and optimization of test processes on a production line. It analyzes options for improving capacity, availability and productivity of processes of an output test by using modern technology available on the market. We have focused on analysis of operation times before and after optimization of test processes at specific production sections. By analyzing measured results we have determined differences in time before and after improvement of the process. We have determined a coefficient of efficiency OEE and by comparing outputs we have confirmed real improvement of the process of the output test of cylinder heads.

Methodological issues in testing the marginal productivity theory

NARCIS (Netherlands)

P.T. Gottschalk (Peter); J. Tinbergen (Jan)

1982-01-01

textabstractPrevious tests of the marginal productivity theory have been criticized on several grounds reviewed by the authors. One important deficiency has been the small number of factor inputs entered in the production functions. In 1978 Gottschalk suggested a method to estimate production

Preliminary Beam Irradiation Test for RI Production Targets at KOMAC

Energy Technology Data Exchange (ETDEWEB)

Yoon, Sang Pil; Kwon, Hyeok Jung; Kim, Han Sung; Cho, Yong Sub; Seol, Kyung Tae; Song, Young Gi; Kim, Dae Il; Jung, Myung Hwan; Kim, Kye Ryung; Min, Yi Sub [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The new beamline and target irradiation facility has been constructed for the production of therapeutic radio-isotope. Sr-82 and Cu-67 were selected as the target isotope in this facility, they are promising isotope for the PET imaging and cancer therapy. For the facility commissioning, the irradiation test for the prototype-target was conducted to confirm the feasibility of radio-isotope production, the proto-type targets are made of RbCl pellet and the natural Zn metal for Sr-82 and Cu-67 production respectively, In this paper, an introduction to the RI production targetry system and the results of the preliminary beam irradiation test are discussed. the low-flux beam irradiation tests for proto-type RI target have been conducted. As a result of the beam irradiation tests, we could obtain the evidence of Sr-82 and Cu-67 production, have confirmed the feasibility of Sr-82 and Cu-67 production at KOMAC RI production facility.

Preliminary Beam Irradiation Test for RI Production Targets at KOMAC

International Nuclear Information System (INIS)

Yoon, Sang Pil; Kwon, Hyeok Jung; Kim, Han Sung; Cho, Yong Sub; Seol, Kyung Tae; Song, Young Gi; Kim, Dae Il; Jung, Myung Hwan; Kim, Kye Ryung; Min, Yi Sub

2016-01-01

The new beamline and target irradiation facility has been constructed for the production of therapeutic radio-isotope. Sr-82 and Cu-67 were selected as the target isotope in this facility, they are promising isotope for the PET imaging and cancer therapy. For the facility commissioning, the irradiation test for the prototype-target was conducted to confirm the feasibility of radio-isotope production, the proto-type targets are made of RbCl pellet and the natural Zn metal for Sr-82 and Cu-67 production respectively, In this paper, an introduction to the RI production targetry system and the results of the preliminary beam irradiation test are discussed. the low-flux beam irradiation tests for proto-type RI target have been conducted. As a result of the beam irradiation tests, we could obtain the evidence of Sr-82 and Cu-67 production, have confirmed the feasibility of Sr-82 and Cu-67 production at KOMAC RI production facility

effect of gamma radiation on some properties of milk and milk products

Energy Technology Data Exchange (ETDEWEB)

Ibrahim, M K

1984-07-01

The aim of this work was to study the effect of gamma irradiation (safety doses to 0.75 M rad) on some properties of milk and some dairy products. Attention was focused on the behaviour of some nuisance and hazardous groups of microorganisms as well as some other properties towards irradiation of cows', buffaloes' and goats' milk. In addition , a study of the properties of their milk fat including its constants and fatty acids composition was undertaken . The utilization of this technique in the prolongation of the shelf life of some dairy products was also investigated.

effect of gamma radiation on some properties of milk and milk products

International Nuclear Information System (INIS)

Ibrahim, M.K.

1984-01-01

The aim of this work was to study the effect of gamma irradiation (safety doses to 0.75 M rad) on some properties of milk and some dairy products. Attention was focused on the behaviour of some nuisance and hazardous groups of microorganisms as well as some other properties towards irradiation of cows', buffaloes' and goats' milk. In addition , a study of the properties of their milk fat including its constants and fatty acids composition was undertaken . The utilization of this technique in the prolongation of the shelf life of some dairy products was also investigated

Estimation of physicochemical properties of 2-ethylhexyl-4-methoxycinnamate (EHMC) degradation products and their toxicological evaluation.

Science.gov (United States)

Gackowska, Alicja; Studziński, Waldemar; Kudlek, Edyta; Dudziak, Mariusz; Gaca, Jerzy

2018-06-01

The organic UV filters, commonly used in personal protection products, are of concern because of their potential risk to aquatic ecosystems and living organisms. One of UV filters is ethylhexyl-4-methoxycinnamate (EHMC) acid. Studies have shown that, in the presence of oxidizing and chlorinating factors, EHMC forms a series of products with different properties than the substrate. In this study, the toxicities of EHMC and its transformation/degradation products formed under the influence of NaOCl/UV and H 2 O 2 /UV systems in the water medium were tested using Microtox® bioassay and by observation of mortality of juvenile crustaceans Daphnia magna and Artemia Salina. We have observed that oxidation and chlorination products of EHMC show significantly higher toxicity than EHMC alone. The toxicity of chemicals is related to their physicochemical characteristic such as lipophilicity and substituent groups. With the increase in lipophilicity of products, expressed as log K OW , the toxicity (EC 50 ) increases. On the basis of physicochemical properties such as vapour pressure (VP), solubility (S), octanol-water partition coefficient (K OW ), bioconcentration factor (BCF) and half-lives, the overall persistence (P OV ) and long-range transport potential (LRTP) of all the products and EHMC were calculated. It was shown that the most persistent and traveling on the long distances in environment are methoxyphenol chloroderivatives, then methoxybenzene chloroderivatives, EHMC chloroderivatives, methoxybenzaldehyde chloroderivatives and methoxycinnamate acid chloroderivatives. These compounds are also characterised by high toxicity.

Investigations regarding the lowering of specific intellectual property risks identified in the production process

Directory of Open Access Journals (Sweden)

Pakocs Ramona

2017-01-01

Full Text Available The main purpose of this research is to decrease the emergence of specific intellectual property risks within the production process as well as increasing risk management performance of IP by preventing them. In order to achieve this, previous studies regarding the main specific intellectual property risks from industrial companies were analyzed together with their managerial methods as well as the possibility of reducing their emergence. As a result of the research conducted were identified five types of intellectual property risks that have a high potential of emergence in the production process, namely: the risk of production of goods in violation of IP rights; the know-how, production knowledge and trade secret disclosure risk; the technological risk of unprotected utility models; the technological risk of unprotected integrated circuits topographies and finally the risk of product counterfeit. In order to achieve the main purpose of our investigation, we have proposed new formulas for estimating the specific intellectual property risks identified in the production process. Their purpose was to minimalize the risk’s negative effects on industrial companies and to increase the managerial performance from the intellectual property domain through a new type of management appropriately named: intellectual property management. The research is finalized with a case study regarding the lapse of rights of a patented invention. Based on a case analysis, it was proved that the exploitation of an invention without a contract represents a counterfeit.

Study on properties and testing methods of thermo-responsive cementing system for well cementing in heavy oil thermal recovery

Science.gov (United States)

Li, Lianjiang

2017-08-01

In this paper, thermo-responsive cement slurry system were being developed, the properties of conventional cement slurry, compressive strength high temperature of cement sheath, mechanical properties of cement sheath and thermal properties of cement sheath were being tested. Results were being used and simulated by Well-Life Software, Thermo-responsive cement slurry system can meet the requirements of heavy oil thermal recovery production. Mechanical and thermal properties of thermo-responsive cement sheath were being tested. Tensile fracture energy of the thermo-responsive cement sheath is larger than conventional cement. The heat absorption capacity of conventional cement sheath is larger than that of thermo-responsive cement sheath, this means more heat is needed for the unit mass once increasing 1.0 °C, which also indicates that thermo-responsive cement own good heat insulating and preservation effects. The heat conductivity coefficient and thermal expansion coefficient of thermo-responsive cement is less than and conventional cement, this means that thermo-responsive cement have good heat preservation and insulation effects with good thermal expansion stabilities.

Dairy product intake and bone properties in 70-year-old men and women.

Science.gov (United States)

Hallkvist, Olle M; Johansson, Jonas; Nordström, Anna; Nordström, Peter; Hult, Andreas

2018-01-29

In the present population-based study including 70-year-old men and women, total dairy product intake was associated with a weak positive association with tibia trabecular and cortical cross-sectional areas. Milk consumption has recently been suggested to increase fracture risk. Therefore, we aimed to investigate associations between dairy product consumption and peripheral bone properties. Furthermore, we explored whether consumption of milk and fermented dairy products affected bone properties differently. The Healthy Aging Initiative is a population-based, cross-sectional study investigating the health of 70-year-old men and women. Out of the 2904 individuals who met the inclusion criteria, data on self-reported daily dairy product consumption (dl/day), peripheral quantitative computed tomography (pQCT) examinations at the 4 and 66% scan sites of the tibia and radius, and dual-energy X-ray absorptiometry (DXA) scans were collected from 2040 participants. Associations between dairy product consumption and bone properties were examined using multiple linear regression models adjusted for sex, muscle area, meal size, dietary protein proportion, current smoking status, and objectively measured physical activity. Total dairy product intake was associated with larger trabecular (2.296 (95% CI, 0.552-4.039) mm 2 , per dl/day increase, p = 0.01) and cortical cross-sectional areas (CSAs) in the tibia (1.757 (95% CI, 0.683-2.830 mm 2 , p = 0.001) as measured by pQCT and higher areal bone mineral density (aBMD) of the radius (3.231 (95% CI, 0.764-5.698) mg/cm 2 , p = 0.01) as measured by DXA. No other measurement in the tibia, radius, femoral neck, or lower spine was associated significantly with dairy product intake. Bone properties did not differ according to the type of dairy product consumed. No evidence of a negative association between dairy product consumption and bone health was found. Furthermore, total dairy product consumption was associated with

Biodiesel production from various feedstocks and their effects on the fuel properties.

Science.gov (United States)

Canakci, M; Sanli, H

2008-05-01

Biodiesel, which is a new, renewable and biological origin alternative diesel fuel, has been receiving more attention all over the world due to the energy needs and environmental consciousness. Biodiesel is usually produced from food-grade vegetable oils using transesterification process. Using food-grade vegetable oils is not economically feasible since they are more expensive than diesel fuel. Therefore, it is said that the main obstacle for commercialization of biodiesel is its high cost. Waste cooking oils, restaurant greases, soapstocks and animal fats are potential feedstocks for biodiesel production to lower the cost of biodiesel. However, to produce fuel-grade biodiesel, the characteristics of feedstock are very important during the initial research and production stage since the fuel properties mainly depend on the feedstock properties. This review paper presents both biodiesel productions from various feedstocks and their effects on the fuel properties.

The behavior of fission products during nuclear rocket reactor tests

International Nuclear Information System (INIS)

Bokor, P.C.; Kirk, W.L.; Bohl, R.J.

1991-01-01

Fission product release from nuclear rocket propulsion reactor fuel is an important consideration for nuclear rocket development and application. Fission product data from the last six reactors of the Rover program are collected in this paper to provide as basis for addressing development and testing issues. Fission product loss from the fuel will depend on fuel composition and reactor design and operating parameters. During ground testing, fission products can be contained downstream of the reactor. The last Rover reactor tested, the Nuclear Furnance, was mated to an effluent clean-up system that was effective in preventing the discharge of fission products into the atmosphere

Central location test vs. home use test: Contrasting results depending on product type

NARCIS (Netherlands)

Boutrolle, I.; Delarue, J.; Arranz, D.; Rogeaux, M.; Köster, E.P.

2007-01-01

Marketing professionals and sensory scientists have several hedonic testing methods at their disposal to assess product acceptability. The central location test (CLT) which usually takes place in a standardised location under controlled conditions is more frequently used than the home use test

Transport processes in partially saturate concrete: Testing and liquid properties

Science.gov (United States)

Villani, Chiara

The measurement of transport properties of concrete is considered by many to have the potential to serve as a performance criterion that can be related to concrete durability. However, the sensitivity of transport tests to several parameters combined with the low permeability of concrete complicates the testing. Gas permeability and diffusivity test methods are attractive due to the ease of testing, their non-destructive nature and their potential to correlate to in-field carbonation of reinforced concrete structures. This work was aimed at investigating the potential of existing gas transport tests as a way to reliably quantify transport properties in concrete. In this study gas permeability and diffusivity test methods were analyzed comparing their performance in terms of repeatability and variability. The influence of several parameters was investigated such as moisture content, mixture proportions and gas flow. A closer look to the influence of pressure revealed an anomalous trend of permeability with respect to pressure. An alternative calculation is proposed in an effort to move towards the determination of intrinsic material properties that can serve as an input for service life prediction models. The impact of deicing salts exposure was also analyzed with respect to their alteration of the degree of saturation as this may affect gas transport in cementitious materials. Limited information were previously available on liquid properties over a wide range of concentrations. To overcome this limitation, this study quantified surface tension, viscosity in presence of deicing salts in a broad concentration range and at different temperatures. Existing models were applied to predict the change of fluid properties during drying. Vapor desorption isotherms were obtained to investigate the influence of deicing salts presence on the non-linear moisture diffusion coefficient. Semi-empirical models were used to quantify the initiation and the rate of drying using liquid

Major advances in testing of dairy products: milk component and dairy product attribute testing.

Science.gov (United States)

Barbano, D M; Lynch, J M

2006-04-01

Milk component analysis is relatively unusual in the field of quantitative analytical chemistry because an analytical test result determines the allocation of very large amounts of money between buyers and sellers of milk. Therefore, there is high incentive to develop and refine these methods to achieve a level of analytical performance rarely demanded of most methods or laboratory staff working in analytical chemistry. In the last 25 yr, well-defined statistical methods to characterize and validate analytical method performance combined with significant improvements in both the chemical and instrumental methods have allowed achievement of improved analytical performance for payment testing. A shift from marketing commodity dairy products to the development, manufacture, and marketing of value added dairy foods for specific market segments has created a need for instrumental and sensory approaches and quantitative data to support product development and marketing. Bringing together sensory data from quantitative descriptive analysis and analytical data from gas chromatography olfactometry for identification of odor-active compounds in complex natural dairy foods has enabled the sensory scientist and analytical chemist to work together to improve the consistency and quality of dairy food flavors.

46 CFR 163.003-27 - Production tests and examination.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Production tests and examination. 163.003-27 Section 163... examination. (a) General. Each ladder produced under Coast Guard approval must be tested in accordance with... for effective monitoring throughout the production schedule. (e) Visual examination. The visual...

46 CFR 160.017-27 - Production tests and examination.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Production tests and examination. 160.017-27 Section 160... examination. (a) General. Each ladder manufactured under Coast Guard approval must be tested in accordance... for effective monitoring throughout the production schedule. (e) Visual examination. The visual...

Relevance of microbial finished product testing in food safety management

NARCIS (Netherlands)

Zwietering, M.H.; Jacxsens, L.; Membre, J.M.; Nauta, M.; Peterz, M.

2016-01-01

Management of microbiological food safety is largely based on good design of processes, products and procedures. Finished product testing may be considered as a control measure at the end of the production process. However, testing gives only very limited information on the safety status of a food.

ConocoPhillips Gas Hydrate Production Test

Energy Technology Data Exchange (ETDEWEB)

Schoderbek, David [ConocoPhillips Co., Houston, TX (United States); Farrell, Helen [ConocoPhillips Co., Houston, TX (United States); Howard, James [ConocoPhillips Co., Houston, TX (United States); Raterman, Kevin [ConocoPhillips Co., Houston, TX (United States); Silpngarmlert, Suntichai [ConocoPhillips Co., Houston, TX (United States); Martin, Kenneth [ConocoPhillips Co., Houston, TX (United States); Smith, Bruce [ConocoPhillips Co., Houston, TX (United States); Klein, Perry [ConocoPhillips Co., Houston, TX (United States)

2013-06-30

Work began on the ConocoPhillips Gas Hydrates Production Test (DOE award number DE-NT0006553) on October 1, 2008. This final report summarizes the entire project from January 1, 2011 to June 30, 2013.

The correlation between composition, structure and properties of high-level waste solidification products

International Nuclear Information System (INIS)

Neumann, L.; Vojtech, O.; Santarova, M.; Stejskal, I.; Gulinskij, V.

1977-01-01

The final product of a high-level liquid waste solidification process must meet a number of quantitative criteria. The necessary data can be obtained by direct measurement of certain parameters of the product (leachability of important radionuclides from the basic matrix, total solubility of the final product, thermal conductivity, mechanical properties, the temperature dependence of viscosity, etc.). Some insight can also be obtained on the basis of a profound analysis of micro- and macrostructure of the solid product. Detailed knowledge of the structure makes it easier to evaluate the final product. In this paper an effort is made to find a relationship between composition and structure of the system and the properties of the product obtained under the specific conditions of the process. The results are demonstrated using a phosphate matrix in which fission products and corrosion products are included in a wide range of concentrations. For analysis of the structure properties, X-ray diffraction, microscopic and electron probe microanalysis (back-scattered electrons and characteristic X-radiation detection) have been used. Using standard methods, the hydrolytical resistance of the product and the selective leachability of caesium, strontium and rare-earth ions have been measured. The results obtained so far have confirmed the usefulness of structure analysis as a parallel method for product evaluation in the development of the process and probably also for large-scale application. (author)

Chemical properties and colors of fermenting materials in salmon fish sauce production

Directory of Open Access Journals (Sweden)

Mitsutoshi Nakano

2018-02-01

Full Text Available This data article reports the chemical properties (moisture, pH, salinity, and soluble solid content and colors of fermenting materials in salmon fish sauce products. The fish sauce was produced by mixing salt with differing proportions of raw salmon materials and fermenting for three months; the salmon materials comprised flesh, viscera, an inedible portion, and soft roe. Chemical properties and colors of the unrefined fish sauce (moromi, and the refined fish sauce, were analyzed at one, two, and three months following the start of fermentation. Data determined for all products are provided in table format. Keywords: Fish sauce, Chum salmon, Fermentation, Chemical properties, Color

Effect of in situ exopolysaccharide production on physicochemical, rheological, sensory, and microstructural properties of the yogurt drink ayran: an optimization study based on fermentation kinetics.

Science.gov (United States)

Yilmaz, M T; Dertli, E; Toker, O S; Tatlisu, N B; Sagdic, O; Arici, M

2015-03-01

Exopolysaccharide (EPS)-producing starter cultures are preferred for the manufacture of fermented milk products to improve rheological and technological properties. However, no clear correlation exists between EPS production and the rheological and technological properties of fermented milk products such as the yogurt drink ayran. In this study, 4 different strain conditions (EPS- and EPS+ Streptococcus thermophilus strains) were tested as a function of incubation temperature (32, 37, or 42°C) and time (2, 3, or 4 h) to determine the effect of culture type and in situ EPS production on physicochemical, rheological, sensory, and microstructural properties of ayran. Furthermore, we assessed the effect of fermentation conditions on amounts of EPS production by different EPS-producing strains during ayran production. A multifactorial design of response surface methodology was used to model linear, interaction, and quadratic effects of these variables on steady shear rheological properties of ayran samples and in situ EPS production levels. The physicochemical and microbiological characteristics of ayran samples altered depending on incubation conditions and strain selection. Steady shear tests showed that ayran samples inoculated with EPS+ strains exhibited pseudoplastic flow behavior. Production of ayran with EPS- strain (control sample) resulted in the lowest apparent viscosity values (η50), whereas those produced with the combination of 2 EPS+ strains yielded ayran with notably increased η50 values. We concluded that incubation time was the variable with the greatest effect on η50, consistency coefficient (K), and flow behavior index (n) values. In situ EPS production was also affected by these conditions during ayran fermentation in which strain-specific metabolism conditions were found to be the most important factor for EPS production. In addition, these findings correlated the amount of in situ EPS produced with the rheological properties of ayran. Scanning

Overview of studies on the effect of recycled aggregates sourced from tested cylinders on concrete material and structural properties

Directory of Open Access Journals (Sweden)

Bilal Hamad

2017-01-01

Full Text Available The paper presents an overview of a two-phase research program that was designed at the American University of Beirut (AUB to investigate the effect of replacing different percentages of natural coarse aggregates (NCA with recycled coarse aggregates (RCA on the properties of the produced concrete. The source of RCA was tested cylinders in batching plants which would help recycling and reusing portion of the waste products of the concrete industry. In the first phase, the fresh and hardened mechanical properties of the produced concrete mix were investigated. The variables were the concrete strength (28 or 60 MPa and the percentage replacement of NCA with RCA from crushed tested cylinders [0 (control, 20, 40, 60, 80, or 100%. Normal strength tested cylinders were used as source of the recycled aggregates for the normal strength concrete (NSC mix and high strength tested cylinders were used for the high strength concrete (HSC mix. Tests included plastic state slump and hardened state mechanical properties including cylinder compressive strength, cylinder splitting tensile strength, modulus of elasticity, and standard beams flexural strength. The results indicated no significant effect on the slump and around 10% average reduction in the hardened mechanical properties for both investigated levels of concrete compressive strength. In the second phase, the structural behavior of normal strength concrete (NSC reinforced concrete beams prepared by replacing different percentages of NCA with RCA from tested concrete cylinders was studied. For each of three modes of failure (flexural, shear, or bond splitting, three beams with different percentages replacement [0 (control, 40, or 100 percent] were tested. One replicate was prepared for each beam to validate the test results. Results indicated no significant difference in the ultimate load reached or load-deflection behavior that could be related to the percentage replacement of NCA with RCA.

Empirical testing of forecast update procedure forseasonal products

DEFF Research Database (Denmark)

Wong, Chee Yew; Johansen, John

2008-01-01

Updating of forecasts is essential for successful collaborative forecasting, especially for seasonal products. This paper discusses the results of a theoretical simulation and an empirical test of a proposed time-series forecast updating procedure. It involves a two-stage longitudinal case study...... of a toy supply chain. The theoretical simulation involves historical weekly consumer demand data for 122 toy products. The empirical test is then carried out in real-time with 291 toy products. The results show that the proposed forecast updating procedure: 1) reduced forecast errors of the annual...... provided less forecast accuracy improvement and it needed a longer time to achieve relatively acceptable forecast uncertainty....

Supply Inventory Management: Property Accountability at Research , Development, Test, and Evaluation Installations

National Research Council Canada - National Science Library

2002-01-01

.... This report evaluates the Military Departments' improvement in maintaining property accountability over personal property at research, development, test, and evaluation installations, Personal...

Reliability of nondestructive testing of metal strength properties for power equipment

International Nuclear Information System (INIS)

Bugaj, N.V.; Lebedev, A.A.; Sharko, A.V.

1985-01-01

Ultrasonic control which is a constituent part of a complex control system which includes specimen-free (by hardness) tests, random breaking tests and acoustic measurements is stUdied for its reliability with respect to strength properties of power-equipment metal. Quantitative and alternative criteria are developed to estimate quality of elements for power-equipment according to results of metal strength properties. Acoustic control results are presented for ultimate strength in 12Kh1MF-steel

Energy condensed packaged systems. Composition, production, properties

Directory of Open Access Journals (Sweden)

Igor L. Kovalenko

2015-03-01

Full Text Available In this paper it is presented the substantiation of choice of fuel phase composition and optimal technology of emulsion production on the basis of binary solution of ammonium and calcium nitrates, which provide the obtaining of energy condensed packaged systems with specified properties. The thermal decomposition of energy condensed systems on the basis of ammonium nitrate is investigated. It is shown that the fuel phase of emulsion systems should be based on esters of polyunsaturated acids or on combinations thereof with petroleum products. And ceresin or petroleum wax can be used as the structuring additive. The influence of the technology of energy condensed systems production on the physicochemical and detonation parameters of emulsion explosives is considered. It is shown the possibility of obtaining of emulsion systems with dispersion of 1.3...1.8 microns and viscosity higher than 103 Pa∙s in the apparatus of original design. The sensitizing effect of chlorinated paraffin CP-470 on the thermolysis of energy condensed emulsion system is shown. The composition and production technology of energy condensed packaged emulsion systems of mark Ukrainit-P for underground mining in mines not dangerous on gas and dust are developed.

Production of a handbook: Nd-doped glass spectroscopic and physical properties

International Nuclear Information System (INIS)

Saroyan, R.A.

1979-01-01

The production of Lawrence Livermore Laboratory publication M-095, a handbook containing a collection of properties of Nd 3+ -doped glasses, is described. The pros and cons of the method are presented. The bulk of the report is contained in detailed appendices which cover major aspects of production

Tests for development of estimation technology of reactor core deformation. Report No.1: fundamental mechanical properties of wrapper tube (test report)

International Nuclear Information System (INIS)

Nishiura, Takeo; Shimazaki, Yuji; Horikiri, Morito

1998-10-01

Mechanical properties such as local contact compression stiffness, bending stiffness, deformation properties, material properties, and friction properties of a wrapper tube structure were clarified experimentally, which can be used as the basic data for development of estimation technology of reactor core deformation. Contents of the Tests data as follows: (1) Effects of load supporting boundary conditions, whether or not a contact-proof pad is attached, and length of duct, on cross section deformation of wrapper tube were made clear as the local contact compression stiffness characteristics. (2) Bending stiffness does not depend on the difference of load supporting boundary conditions. The property of cross section deformation under bending load was obtained. (3) The deformation modes and the strain distributions were obtained by the deformation tests of wrapper tube. (4) The stress-strain diagrams including plastic range under various strain variation rates were obtained by the material tests at room temperature. (5) The static and the dynamic friction coefficients by various contact angles and the contact loads between contact-proof pads of two wrapper tubes were obtained by friction property tests. (author)

Testing program for determining the mechanical properties of concrete to temperatures of 6210C

International Nuclear Information System (INIS)

Oland, C.B.; Naus, D.J.; Robinson, G.C.

1980-01-01

Concrete temperatures in a Liquid Metal Fast Breeder Reactor (LMFBR) in excess of normal code limits can result from postulated large sodium spills in equipment cells. Elevated temperature concrete property data which may have application for providing a basis for the design and evaluation of such postulated accident conditions is limited. Data thus needed to be developed commensurate with LMFBR plant applications for critical physical and mechanical concrete properties under prototypic thermal accident conditions. A test program was conducted to define the variations in physical and mechanical properties of a limestone aggregate concrete and a lightweight insulating concrete exposed to elevated temperatures. Five test series were conducted: unconfined compression, shear, rebar bond, sustained loading (creep), and thermal properties. Testing procedures for determining the mechanical properties of concrete from ambient to 621 0 C (1150 0 F) are described. Ther thermal properties tests are discussed in a separate paper which is also being presented at this conference

General overview of graphene: Production, properties and application in polymer composites

International Nuclear Information System (INIS)

Phiri, Josphat; Gane, Patrick; Maloney, Thad C.

2017-01-01

Highlights: • Three aspects of graphene have been reviewed: properties, fabrication and polymer composites. • Scalability potential of graphite based exfoliation methods is discussed. • Graphene produced via GO and LPE methods is compared in polymer composite applications. - Abstract: Graphene is a new and exciting material that has attracted much attention in the last decade and is being extensively explored because of its properties, which have been described with so many superlatives. Production of graphene for large scale application is still a major challenge. Top-down graphene exfoliation methods from graphite, such as liquid-phase exfoliation which is promising because of low cost and high scalability potential will be briefly discussed. We also analyze the challenges and possibilities of using graphene as a nanofiller in polymer composites which has resulted in enhanced electrical, mechanical and thermal properties. In this review, we take a panoramic approach to give insight on the different aspects of graphene such as properties, graphite-based production methods and also examples of graphene application in polymer composites and which will be beneficial to both novice and experts.

General overview of graphene: Production, properties and application in polymer composites

Energy Technology Data Exchange (ETDEWEB)

Phiri, Josphat, E-mail: josphat.phiri@aalto.fi [School of Chemical Technology, Department of Forest Products Technology, Aalto University, P.O. Box 16300, 00076 Aalto (Finland); Gane, Patrick [School of Chemical Technology, Department of Forest Products Technology, Aalto University, P.O. Box 16300, 00076 Aalto (Finland); Omya International AG, CH-4665 Oftringen (Switzerland); Maloney, Thad C., E-mail: thaddeus.maloney@aalto.fi [School of Chemical Technology, Department of Forest Products Technology, Aalto University, P.O. Box 16300, 00076 Aalto (Finland)

2017-01-15

Highlights: • Three aspects of graphene have been reviewed: properties, fabrication and polymer composites. • Scalability potential of graphite based exfoliation methods is discussed. • Graphene produced via GO and LPE methods is compared in polymer composite applications. - Abstract: Graphene is a new and exciting material that has attracted much attention in the last decade and is being extensively explored because of its properties, which have been described with so many superlatives. Production of graphene for large scale application is still a major challenge. Top-down graphene exfoliation methods from graphite, such as liquid-phase exfoliation which is promising because of low cost and high scalability potential will be briefly discussed. We also analyze the challenges and possibilities of using graphene as a nanofiller in polymer composites which has resulted in enhanced electrical, mechanical and thermal properties. In this review, we take a panoramic approach to give insight on the different aspects of graphene such as properties, graphite-based production methods and also examples of graphene application in polymer composites and which will be beneficial to both novice and experts.

Visible-light activate Ag/WO3 films based on wood with enhanced negative oxygen ions production properties

Science.gov (United States)

Gao, Likun; Gan, Wentao; Cao, Guoliang; Zhan, Xianxu; Qiang, Tiangang; Li, Jian

2017-12-01

The Ag/WO3-wood was fabricated through a hydrothermal method and a silver mirror reaction. The system of visible-light activate Ag/WO3-wood was used to produce negative oxygen ions, and the effect of Ag nanoparticles on negative oxygen ions production was investigated. From the results of negative oxygen ions production tests, it can be observed that the sample doped with Ag nanoparticles, the concentration of negative oxygen ions is up to 1660 ions/cm3 after 60 min visible light irradiation. Moreover, for the Ag/WO3-wood, even after 60 min without irradiation, the concentration of negative oxygen ions could keep more than 1000 ions/cm3, which is up to the standard of the fresh air. Moreover, due to the porous structure of wood, the wood acted as substrate could promote the nucleation of nanoparticles, prevent the agglomeration of the particles, and thus lead the improvement of photocatalytic properties. And such wood-based functional materials with the property of negative oxygen ions production could be one of the most promising materials in the application of indoor decoration materials, which would meet people's pursuit of healthy, environment-friendly life.

Recycled aggregates in concrete production: engineering properties and environmental impact

Directory of Open Access Journals (Sweden)

Seddik Meddah Mohammed

2017-01-01

Full Text Available Recycled concrete aggregate is considered as the most abundant and used secondary aggregate in concrete production, other types of solid waste are also being used in concrete for specific purposes and to achieve some desired properties. Recycled aggregates and particularly, recycled concrete aggregate substantially affect the properties and mix design of concrete both at fresh and hardened states since it is known by high porosity due to the adhered layer of old mortar on the aggregate which results in a high water absorption of the recycled secondary aggregate. This leads to lower density and strength, and other durability related properties. The use of most recycled aggregate in concrete structures is still limited to low strength and non-structural applications due to important drop in strength and durability performances generated. Embedding recycled aggregates in concrete is now a current practice in many countries to enhance sustainability of concrete industry and reduce its environmental impacts. The present paper discusses the various possible recycled aggregates used in concrete production, their effect on both fresh and hardened properties as well as durability performances. The economic and environmental impacts of partially or fully substituting natural aggregates by secondary recycled aggregates are also discussed.

Properties of Douglas Point Generating Station heat transport corrosion products

International Nuclear Information System (INIS)

Montford, B.; Rummery, T.E.

1975-09-01

Chemical, radiochemical and structural properties of circulating and fixed corrosion products from the Douglas Point Generating Station are documented. Interaction of Monel-400 and carbon steel corrosion products is described, and the mechanisms of Monel-400 surface deposit release, and activity buildup in the coolant system, are briefly discussed. Efficiencies of filters and ion-exchangers for the removal of released radionuclides are given. (author)

Foam property tests to evaluate the potential for longwall shield dust control.

Science.gov (United States)

Reed, W R; Beck, T W; Zheng, Y; Klima, S; Driscoll, J

2018-01-01

Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration's lower coal mine respirable dust standard of 1.5 mg/m 3 . Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control.

Production and several properties of single crystal austenitic stainless steels

International Nuclear Information System (INIS)

Okamoto, Kazutaka; Yoshinari, Akira; Kaneda, Junya; Aono, Yasuhisa; Kato, Takahiko

1998-01-01

The single crystal austenitic stainless steels Type 316L and 304L were grown in order to improve the resistance to stress corrosion cracking (SCC) using a unidirectional solidification method which can provide the large size single crystals. The mechanical properties and the chemical properties were examined. The orientation and temperature dependence of tensile properties of the single crystals were measured. The yield stress of the single crystal steels are lower than those of the conventional polycrystal steels because of the grain boundary strength cannot be expected in the single crystal steels. The tensile properties of the single crystal austenitic stainless steel Type 316L depend strongly on the orientation. The tensile strength in orientation are about 200 MPa higher than those in the and orientations. The microstructure of the single crystal consists of a mixture of the continuous γ-austenitic single crystal matrix and the δ-ferrite phase so that the effects of the γ/δ boundaries on the chemical properties were studied. The effects of the δ-ferrite phases and the γ/δ boundaries on the resistance to SCC were examined by the creviced bent beam test (CBB test). No crack is observed in all the CBB test specimens of the single crystals, even at the γ/δ boundaries. The behavior of the radiation induced segregation (RIS) at the γ/δ boundaries in the single crystal austenitic stainless steel Type 316L was evaluated by the electron irradiation test in the high voltage electron microscope (HVEM). The depletion of oversized solute chromium at the γ/δ boundary in the single crystal austenitic stainless steel Type 316L is remarkably lower than that at the grain boundary in the polycrystalline-type 316L. (author)

Methodology for Mechanical Property Testing on Fuel Cladding Using an Expanded Plug Wedge Test

Energy Technology Data Exchange (ETDEWEB)

Wang, Jy-An John [ORNL; Jiang, Hao [ORNL

2013-08-01

To determine the tensile properties of irradiated fuel cladding in a hot cell, a simple test was developed at ORNL and is described fully in US Patent Application 20060070455, Expanded plug method for developing circumferential mechanical properties of tubular materials. This method is designed for testing fuel rod cladding ductility in a hot cell utilizing an expandable plug to stretch a small ring of irradiated cladding material. The specimen strain is determined using the measured diametrical expansion of the ring. This method removes many complexities associated with specimen preparation and testing. The advantages are the simplicity of measuring the test component assembly in the hot cell and the direct measurement of specimen strain. It was also found that cladding strength could be determined from the test results. The basic approach of this test method is to apply an axial compressive load to a cylindrical plug of polyurethane (or other materials) fitted inside a short ring of the test material to achieve radial expansion of the specimen. The diameter increase of the specimen is used to calculate the circumferential strain accrued during the test. The other two basic measurements are total applied load and amount of plug compression (extension). A simple procedure is used to convert the load circumferential strain data from the ring tests into material pseudo-stress-strain curves. However, several deficiencies exist in this expanded-plug loading ring test, which will impact accuracy of test results and introduce potential shear failure of the specimen due to inherited large axial compressive stress from the expansion plug test. First of all, the highly non-uniform stress and strain distribution resulted in the gage section of the clad. To ensure reliable testing and test repeatability, the potential for highly non-uniform stress distribution or displacement/strain deformation has to be eliminated at the gage section of the specimen. Second, significant

Development and Justification of a Risk Evaluation Matrix To Guide Chemical Testing Necessary To Select and Qualify Plastic Components Used in Production Systems for Pharmaceutical Products.

Science.gov (United States)

Jenke, Dennis

2015-01-01

An accelerating trend in the pharmaceutical industry is the use of plastic components in systems used to produce an active pharmaceutical ingredient or a finished drug product. If the active pharmaceutical ingredient, the finished drug product, or any solution used to generate them (for example, a process stream such as media, buffers, eluents, and the like) is contacted by a plastic component at any time during the production process, substances leached from the component may accumulate in the active pharmaceutical ingredient or finished drug product, affecting its safety and/or efficacy. In this article the author develops and justifies a semi-quantitative risk evaluation matrix that is used to determine the amount and rigor of component testing necessary and appropriate to establish that the component is chemically suitable for its intended use. By considering key properties of the component, the contact medium, the contact conditions, and the active pharmaceutical ingredient's or finished drug product's clinical conditions of use, use of the risk evaluation matrix produces a risk score whose magnitude reflects the accumulated risk that the component will interact with the contact solution to such an extent that component-related extractables will accumulate in the active pharmaceutical ingredient or finished drug product as leachables at levels sufficiently high to adversely affect user safety. The magnitude of the risk score establishes the amount and rigor of the testing that is required to select and qualify the component, and such testing is broadly grouped into three categories: baseline assessment, general testing, and full testing (extractables profiling). Production suites used to generate pharmaceuticals can include plastic components. It is possible that substances in the components could leach into manufacturing solutions and accumulate in the pharmaceutical product. In this article the author develops and justifies a semi-quantitative risk

Production LHC HTS power lead test results

CERN Document Server

Tartaglia, M; Fehér, S; Huang, Y; Orris, D F; Pischalnikov, Y; Rabehl, Roger Jon; Sylvester, C D; Zbasnik, J

2005-01-01

The Fermilab Magnet test facility has built and operated a test stand to characterize the performance of HTS power leads. We report here the results of production tests of 20 pairs of 7.5 kA HTS power leads manufactured by industry for installation in feed boxes for the LHC Interaction Region quadrupole strings. Included are discussions of the thermal, electrical, and quench characteristics under "standard" and "extreme" operating conditions, and the stability of performance across thermal cycles.

Production LHC HTS power lead test results

International Nuclear Information System (INIS)

Tartaglia, M.A.; Carcagno, R.H.; Feher, S.; Huang, Y.; Orris, D.F.; Pischalnikov, Y.; Rabehl, R.J.; Sylvester, C.; Zbasnik, J.

2004-01-01

The Fermilab Magnet test facility has built and operated a test stand to characterize the performance of HTS power leads. We report here the results of production tests of 20 pairs of 7.5 kA HTS power leads manufactured by industry for installation in feed boxes for the LHC Interaction Region quadrupole strings. Included are discussions of the thermal, electrical, and quench characteristics under ''standard'' and ''extreme'' operating conditions, and the stability of performance across thermal cycles

Experimental method for testing diffraction properties of reflection waveguide holograms.

Science.gov (United States)

Xie, Yi; Kang, Ming-Wu; Wang, Bao-Ping

2014-07-01

Waveguide holograms' diffraction properties include peak wavelength and diffraction efficiency, which play an important role in determining their display performance. Based on the record and reconstruction theory of reflection waveguide holograms, a novel experimental method for testing diffraction properties is introduced and analyzed in this paper, which uses a plano-convex lens optically contacted to the surface of the substrate plate of the waveguide hologram, so that the diffracted light beam can be easily detected. Then an experiment is implemented. The designed reconstruction wavelength of the test sample is 530 nm, and its diffraction efficiency is 100%. The experimental results are a peak wavelength of 527.7 nm and a diffraction efficiency of 94.1%. It is shown that the tested value corresponds well with the designed value.

Thermal Exposure Effects on Properties of Al-Li Alloy Plate Products

Science.gov (United States)

Shah, Sandeep; Wells, Douglas; Wagner, John; Babel, Henry

2003-01-01

The objective of this viewgraph representation is to evaluate the effects of thermal exposure on the mechanical properties of both production mature and developmental Al-Li alloys. The researchers find for these alloys, the data clearly shows that there is no deficit in mechanical properties at lower exposure temperatures in some cases, and a signficant deficit in mechanical properties at higher exposure temperatures in all cases. Topics considered include: Al-Li alloys composition, key characteristics of Al-Li alloys and thermal exposure matrix.

Dissolution testing of intermediary products in uranium dioxide production by the sol-gel method

International Nuclear Information System (INIS)

Melichar, F.; Landspersky, H.; Urbanek, V.

1979-01-01

A method was developed of dissolving polyuranates and uranium dioxides in sulphuric acid and in carbonate solutions for testing intermediate products in the sol-gel process preparation of uranium dioxide. A detailed granulometric analysis of spherical particle dispersion was included as part of the tests. Two different production methods were used for the two types of studied materials. The test results show that the test method is suitable for determining temperature sensitivity of the materials to dissolution reaction. The geometrical distribution of impurities in the spherical particles can be determined from the dissolution kinetics. The method allows the determination of the effect of carbon from impurities on the process of uranium dioxide leaching and is thus applicable for testing materials prepared by the sol-gel method. (Z.M.)

AIP1OGREN: Aerosol Observing Station Intensive Properties Value-Added Product

Energy Technology Data Exchange (ETDEWEB)

Koontz, Annette [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Flynn, Connor [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-09-15

The aip1ogren value-added product (VAP) computes several aerosol intensive properties. It requires as input calibrated, corrected, aerosol extensive properties (scattering and absorption coefficients, primarily) from the Aerosol Observing Station (AOS). Aerosol extensive properties depend on both the nature of the aerosol and the amount of the aerosol. We compute several properties as relationships between the various extensive properties. These intensive properties are independent of aerosol amount and instead relate to intrinsic properties of the aerosol itself. Along with the original extensive properties we report aerosol single-scattering albedo, hemispheric backscatter fraction, asymmetry parameter, and Ångström exponent for scattering and absorption with one-minute averaging. An hourly averaged file is produced from the 1-minute files that includes all extensive and intensive properties as well as submicron scattering and submicron absorption fractions. Finally, in both the minutely and hourly files the aerosol radiative forcing efficiency is provided.

Chemical properties and colors of fermenting materials in salmon fish sauce production.

Science.gov (United States)

Nakano, Mitsutoshi; Sagane, Yoshimasa; Koizumi, Ryosuke; Nakazawa, Yozo; Yamazaki, Masao; Watanabe, Toshihiro; Takano, Katsumi; Sato, Hiroaki

2018-02-01

This data article reports the chemical properties (moisture, pH, salinity, and soluble solid content) and colors of fermenting materials in salmon fish sauce products. The fish sauce was produced by mixing salt with differing proportions of raw salmon materials and fermenting for three months; the salmon materials comprised flesh, viscera, an inedible portion, and soft roe. Chemical properties and colors of the unrefined fish sauce ( moromi ), and the refined fish sauce, were analyzed at one, two, and three months following the start of fermentation. Data determined for all products are provided in table format.

Mechanical properties and structure of Zircaloy attached by UO2+x and fission products

International Nuclear Information System (INIS)

Holub, F.

1987-08-01

The aim of this project was to determine the combined long-term effect of simulated fission products and hyperstoichiometric uranium dioxide on the mechanical properties and structure of Zircaloy. Three groups of fission product elements or compounds were defined: The rare earth oxides CeO 2 , La 2 O 3 , Nd 2 O 3 , Y 2 O 3 ; The metals No, Ru, Ag; The low melting elements Te, Sb and Cd. Each of these groups of fission products was mixed with UO 2+x in proportion related for burnups of 5, 10 and 30%. The simulated fuel mixtures were filled into tubular Zircaloy casings, plugged and welded. These specimens were annealed at 350, 500 and 700 deg. C up to 17,500 hours. The test results indicate different kinds of action of the simulated fuel constituents. Mixtures of rare earth oxides and UO 2+x embrittle Zircaloy drastically at higher temperatures. There exists a mutual intensifying effect of rare earth oxides and UO 2+x . UO 2+x and (Mo + Ru + Ag) and their mixtures act very similar on Zircaloy. The low melting fission products (Te + Sb + Cd) influence the ductility of Zircaloy in an advantageous manner, compared to pure UO 2+x fuel. The layer of zirconium tellurides seems to protect the Zircaloy metal against the embrittling attack of oxygen from UO 2+x . The most important events of tensile tests at 400 deg. C are the high values of the elongation of specimens which are brittled at room temperature. It should guarantee the integrity of fuel elements, which have been attacked chemically by fission products at temperatures of 400 deg. C and higher

Production and decay properties of the delta (970) meson

International Nuclear Information System (INIS)

Gay, J.B.; Chaloupka, V.; Gavillet, Ph.; Hemingway, R.J.; Marzano, F.; Montanet, L.; Blokzijl, R.; Jongejans, B.; Massaro, G.G.G.; Heinen, P.M.; Metzger, W.J.; Timmermans, J.J.M.

1976-01-01

Using an 80 events per microbarn sample of K - p interactions at 4.2 GeV/c the production and decay properties of the delta(970) have been investigated in the following reactions: K - p→Σ + (1385)etaπ - and K - p→Σ + (1385)K 0 K - . (Auth.)

Physical Properties And Maize Production In A Spent Oil ...

African Journals Online (AJOL)

Information on the use of plant species and organic nutrients to improve the physical properties of oil-contaminated soil, with a view to making it conducive for crop production, is very important. Three legumes (Gliricidia sepium, Leucenae leucocephala and Calapogonium caeruleam) combined or not with poultry manure ...

30 CFR 250.1151 - How often must I conduct well production tests?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How often must I conduct well production tests... Requirements Well Tests and Surveys § 250.1151 How often must I conduct well production tests? (a) You must conduct well production tests as shown in the following table: You must conduct: And you must submit to...

The Chandra Source Catalog: Source Properties and Data Products

Science.gov (United States)

Rots, Arnold; Evans, Ian N.; Glotfelty, Kenny J.; Primini, Francis A.; Zografou, Panagoula; Anderson, Craig S.; Bonaventura, Nina R.; Chen, Judy C.; Davis, John E.; Doe, Stephen M.; Evans, Janet D.; Fabbiano, Giuseppina; Galle, Elizabeth C.; Gibbs, Danny G., II; Grier, John D.; Hain, Roger; Hall, Diane M.; Harbo, Peter N.; He, Xiang Qun (Helen); Houck, John C.; Karovska, Margarita; Kashyap, Vinay L.; Lauer, Jennifer; McCollough, Michael L.; McDowell, Jonathan C.; Miller, Joseph B.; Mitschang, Arik W.; Morgan, Douglas L.; Mossman, Amy E.; Nichols, Joy S.; Nowak, Michael A.; Plummer, David A.; Refsdal, Brian L.; Siemiginowska, Aneta L.; Sundheim, Beth A.; Tibbetts, Michael S.; van Stone, David W.; Winkelman, Sherry L.

2009-09-01

The Chandra Source Catalog (CSC) is breaking new ground in several areas. There are two aspects that are of particular interest to the users: its evolution and its contents. The CSC will be a living catalog that becomes richer, bigger, and better in time while still remembering its state at each point in time. This means that users will be able to take full advantage of new additions to the catalog, while retaining the ability to back-track and return to what was extracted in the past. The CSC sheds the limitations of flat-table catalogs. Its sources will be characterized by a large number of properties, as usual, but each source will also be associated with its own specific data products, allowing users to perform mini custom analysis on the sources. Source properties fall in the spatial (position, extent), photometric (fluxes, count rates), spectral (hardness ratios, standard spectral fits), and temporal (variability probabilities) domains, and are all accompanied by error estimates. Data products cover the same coordinate space and include event lists, images, spectra, and light curves. In addition, the catalog contains data products covering complete observations: event lists, background images, exposure maps, etc. This work is supported by NASA contract NAS8-03060 (CXC).

Recycled aggregates in concrete production: engineering properties and environmental impact

OpenAIRE

Seddik Meddah Mohammed

2017-01-01

Recycled concrete aggregate is considered as the most abundant and used secondary aggregate in concrete production, other types of solid waste are also being used in concrete for specific purposes and to achieve some desired properties. Recycled aggregates and particularly, recycled concrete aggregate substantially affect the properties and mix design of concrete both at fresh and hardened states since it is known by high porosity due to the adhered layer of old mortar on the aggregate which ...

Peptides from Fish By-product Protein Hydrolysates and Its Functional Properties: an Overview.

Science.gov (United States)

Zamora-Sillero, Juan; Gharsallaoui, Adem; Prentice, Carlos

2018-04-01

The inadequate management of fish processing waste or by-products is one of the major problems that fish industry has to face nowadays. The mismanagement of this raw material leads to economic loss and environmental problems. The demand for the use of these by-products has led to the development of several processes in order to recover biomolecules from fish by-products. An efficient way to add value to fish waste protein is protein hydrolysis. Protein hydrolysates improve the functional properties and allow the release of peptides of different sizes with several bioactivities such as antioxidant, antimicrobial, antihypertensive, anti-inflammatory, or antihyperglycemic among others. This paper reviews different methods for the production of protein hydrolysates as well as current research about several fish by-products protein hydrolysates bioactive properties, aiming the dual objective: adding value to these underutilized by-products and minimizing their negative impact on the environment.

Modulation of Cytokine Production by Drugs with Antiepileptic or Mood Stabilizer Properties in Anti-CD3- and Anti-CD40-Stimulated Blood In Vitro

Directory of Open Access Journals (Sweden)

Hubertus Himmerich

2014-01-01

Full Text Available Increased cytokine production possibly due to oxidative stress has repeatedly been shown to play a pivotal role in the pathophysiology of epilepsy and bipolar disorder. Recent in vitro and animal studies of valproic acid (VPA report antioxidative and anti-inflammatory properties, and suppression of interleukin (IL-6 and tumor necrosis factor (TNF-α. We tested the effect of drugs with antiepileptic or mood stabilizer properties, namely, primidone (PRM, carbamazepine (CBZ, levetiracetam (LEV, lamotrigine (LTG, VPA, oxcarbazepine (OXC, topiramate (TPM, phenobarbital (PB, and lithium on the production of the following cytokines in vitro: interleukin (IL-1β, IL-2, IL-4, IL-6, IL-17, IL-22, and TNF-α. We performed a whole blood assay with stimulated blood of 14 healthy female subjects. Anti-human CD3 monoclonal antibody OKT3, combined with 5C3 antibody against CD40, was used as stimulant. We found a significant reduction of IL-1 and IL-2 levels with all tested drugs other than lithium in the CD3/5C3-stimulated blood; VPA led to a decrease in IL-1β, IL-2, IL-4, IL-6, IL-17, and TNF-α production, which substantiates and adds knowledge to current hypotheses on VPA’s anti-inflammatory properties.

Avoidance test with Enchytraeus albidus (Enchytraeidae): Effects of different exposure time and soil properties

International Nuclear Information System (INIS)

Amorim, Monica J.B.; Novais, Sara; Roembke, Joerg; Soares, Amadeu M.V.M.

2008-01-01

Enchytraeids are ecologically relevant soil species and are commonly used in standardized toxicity tests. Their rapid reaction to a chemical exposure can be used as a toxicological measurement endpoint that assesses the avoidance behavior. The objectives of this investigation were to determine the effects of soil properties on the avoidance behavior of Enchytraeus albidus and to optimize the duration of avoidance test. The avoidance tests included (1) exposures in OECD artificial soil with standard or modified properties (pH, clay or peat content), and (2) exposures to copper chloride, cadmium chloride, and to the organic pesticides dimethoate and phenmedipham for different time periods. Results showed that alteration of OECD soil constituents significantly affected the avoidance behavior of enchytraeids, and that the 48-h exposure was the optimal duration of the test. Consideration of soil properties is important for selecting appropriate experimental design and interpreting the results of the enchytraeid avoidance test. - Optimal duration of the avoidance tests with potworm Enchytraeus albidus is 48 h; soil properties can affect performance of the test species

A comparative study of the physical and chemical properties of nano-sized ZnO particles from multiple batches of three commercial products

Energy Technology Data Exchange (ETDEWEB)

Yin, Hong [Commonwealth Scientific and Industrial Research Organisation, Manufacturing Flagship (Australia); Coleman, Victoria A. [National Measurement Institute Australia, Nanometrology Section (Australia); Casey, Phil S., E-mail: Phil.Casey@csiro.au [Commonwealth Scientific and Industrial Research Organisation, Manufacturing Flagship (Australia); Angel, Brad [Commonwealth Scientific and Industrial Research Organisation, Land and Water Flagship (Australia); Catchpoole, Heather J. [National Measurement Institute Australia, Nanometrology Section (Australia); Waddington, Lynne [Commonwealth Scientific and Industrial Research Organisation, Manufacturing Flagship (Australia); McCall, Maxine J. [Commonwealth Scientific and Industrial Research Organisation, Food and Nutrition Flagship (Australia)

2015-02-15

Given the broad commercial applications for ZnO nanomaterials, accurate attribution of physicochemical characteristics that induce toxic effects is particularly important. We report on the physicochemical properties of three commercial nano-ZnO products: Z-COTE and Z-COTE HP1 from BASF, and Nanosun from Micronisers, and, for reference, “bulk” ZnO from Sigma-Aldrich. Z-COTE, Nanosun and “bulk” consist of uncoated particles with different sizes, while Z-COTE HP1 consists of nanoparticles with a hydrophobic coating. Specific batches of these ZnO products were included in the OECD Sponsorship Programme to test manufactured nanomaterials. In order to identify properties potentially susceptible to variations between production runs, three additional batches of Z-COTE and Nanosun and two additional batches of Z-COTE HP1 were also investigated here. In general, all products showed little variation between batches for properties measured from powdered samples, but batch variations in the amount of surface coating were evident for the coated Z-COTE HP1. Properties measured with samples dispersed in liquids (agglomeration, photocatalytic activity, dissolution) were highly dependent on dispersion protocols, and this made it difficult to differentiate between differences due to dispersion and due to batches. However, batch-sensitive properties did appear to be present in Z-COTE and Z-COTE HP1 (photocatalytic activity), and Nanosun (dissolution). Intra-batch time and/or storage-dependent changes in the applied surface coating, noted specifically for the OECD batch of Z-COTE HP1, highlight the need for best practice when storing and accessing stocks of nano products. Awareness of inter-batch and intra-batch variability is essential for commercial applications and for nanotoxicological studies aimed at identifying links between physicochemical properties and any adverse effects in biological systems.

A comparative study of the physical and chemical properties of nano-sized ZnO particles from multiple batches of three commercial products

Science.gov (United States)

Yin, Hong; Coleman, Victoria A.; Casey, Phil S.; Angel, Brad; Catchpoole, Heather J.; Waddington, Lynne; McCall, Maxine J.

2015-02-01

Given the broad commercial applications for ZnO nanomaterials, accurate attribution of physicochemical characteristics that induce toxic effects is particularly important. We report on the physicochemical properties of three commercial nano-ZnO products: Z-COTE and Z-COTE HP1 from BASF, and Nanosun from Micronisers, and, for reference, "bulk" ZnO from Sigma-Aldrich. Z-COTE, Nanosun and "bulk" consist of uncoated particles with different sizes, while Z-COTE HP1 consists of nanoparticles with a hydrophobic coating. Specific batches of these ZnO products were included in the OECD Sponsorship Programme to test manufactured nanomaterials. In order to identify properties potentially susceptible to variations between production runs, three additional batches of Z-COTE and Nanosun and two additional batches of Z-COTE HP1 were also investigated here. In general, all products showed little variation between batches for properties measured from powdered samples, but batch variations in the amount of surface coating were evident for the coated Z-COTE HP1. Properties measured with samples dispersed in liquids (agglomeration, photocatalytic activity, dissolution) were highly dependent on dispersion protocols, and this made it difficult to differentiate between differences due to dispersion and due to batches. However, batch-sensitive properties did appear to be present in Z-COTE and Z-COTE HP1 (photocatalytic activity), and Nanosun (dissolution). Intra-batch time and/or storage-dependent changes in the applied surface coating, noted specifically for the OECD batch of Z-COTE HP1, highlight the need for best practice when storing and accessing stocks of nano products. Awareness of inter-batch and intra-batch variability is essential for commercial applications and for nanotoxicological studies aimed at identifying links between physicochemical properties and any adverse effects in biological systems.

Retrogradation of concentrated starch systems : mechanism and consequences for product properties

NARCIS (Netherlands)

Keetels, C.J.A.M.

1995-01-01

The mechanical properties of concentrated starch + water systems were studied during heating, cooling and storage. Methods used were a small-amplitude dynamic rheological test and compression between parallel plates. The mechanical properties were related to the structure of the gels.

Production and properties of solidified high-level waste

International Nuclear Information System (INIS)

Brodersen, K.

1980-08-01

Available information on production and properties of solidified high-level waste are presented. The review includes literature up to the end of 1979. The feasibility of production of various types of solidified high-level wast is investigated. The main emphasis is on borosilicate glass but other options are also mentioned. The expected long-term behaviour of the materials are discussed on the basis of available results from laboratory experiments. Examples of the use of the information in safety analysis of disposal in salt formations are given. The work has been made on behalf of the Danish utilities investigation of the possibilities of disposal of high-level waste in salt domes in Jutland. (author)

Structural, compositional, and sensorial properties of United States commercial ice cream products.

Science.gov (United States)

Warren, Maya M; Hartel, Richard W

2014-10-01

Commercial vanilla ice cream products from the United States (full fat, low fat, and nonfat) were analyzed for their structural, behavioral (i.e., melt rate and drip-through), compositional, and sensorial attributes. Mean size distributions of ice crystals and air cells, drip-through rates, percent partially coalesced fat, percent overrun and total fat, and density were determined. A trained panel carried out sensory analyses in order to determine correlations between ice cream microstructure attributes and sensory properties using a Spectrum(TM) descriptive analysis. Analyses included melt rate, breakdown, size of ice particulates (iciness), denseness, greasiness, and overall creaminess. To determine relationships and interactions, principle component analysis and multivariate pairwise correlation were performed within and between the instrumental and sensorial data. Greasiness and creaminess negatively correlated with drip-through rate and creaminess correlated with percent total fat and percent fat destabilization. Percent fat did not determine the melt rate on a sensorial level. However, drip-through rate at ambient temperatures was predicted by total fat content of the samples. Based on sensory analysis, high-fat products were noted to be creamier than low and nonfat products. Iciness did not correlate with mean ice crystal size and drip-through rate did not predict sensory melt rate. Furthermore, on a sensorial level, greasiness positively correlated with total percent fat destabilization and mean air cell size positively correlated with denseness. These results indicate that commercial ice cream products vary widely in composition, structure, behavior, and sensory properties. There is a wide range of commercial ice creams in the United States market, ranging from full fat to nonfat. In this research we showed that these ice creams vary greatly in their microstructures, behaviors (the melt/drip-though, collapse, and/or stand up properties of ice cream

Electromagnetic NDT to characterize usage properties of flat steel products - Part 2

International Nuclear Information System (INIS)

Altpeter, I.; Dobmann, G.; Szielasko, K.

2015-01-01

The Fraunhofer Institute for Non-destructive Testing (IZFP) in Saarbruecken, Germany, started its activities in materials characterization of flat steel products in the eighties of the last century in the basic program of the European Community of Coal and Steel (ECCS). Throughout the years, continuous research and development were performed. The objective of the work, presented within this three-part series of reports, is to discuss the history of an innovation which began in 1988 with R&D in the area of texture characterization in steel sheets produced for car-body manufacturing (Part 1). In the following years the activities were to automate online property determination in terms of yield strength, tensile strength, planar, and vertical-anisotropy-factors. Again, steel sheets were the focus of the developments and the first NDT systems that came into industrial application for this project. Parallel research was performed to characterize the mechanical properties and hardness of heavy steel plates, mainly produced for pipeline manufacturing and off-shore applications (Part 2) The final report in the series (Part 3) will discuss steel sheet characterization and presents the successful development of a combination-transducer which combines ultrasonics with electromagnetic NDT. (author)

Electromagnetic NDT to characterize usage properties of flat steel products - Part 3

International Nuclear Information System (INIS)

Altpeter, I.; Dobmann, G.; Szielasko, K.

2015-01-01

The Fraunhofer Institute for Nondestructive Testing (IZFP) in Saarbruecken, Germany, started its activities in materials characterization of flat steel products in the eighties of the last century in the basic program of the European Community of Coal and Steel (ECCS). Throughout the years, continuous research and development were performed. The objective of the work, presented within this three-part series of reports, is to discuss the history of an innovation that began in 1988 with R&D in the area of texture characterization in steel sheets produced for car-body manufacturing (Part 1). In the following years the activities were to automate online property determination in terms of yield strength, tensile strength, planar- and vertical-anisotropy factors. Again, steel sheets were the focus of the developments and first NDT systems came into industrial application. Parallel research was performed to characterize the mechanical properties and hardness on heavy steel plates, mainly produced for pipeline manufacturing and offshore applications (Part 2). The final report in the series (Part 3) discusses steel sheet characterization and presents the successful development of a combination transducer that combines ultrasonics with electromagnetic NDT. (author)

Electromagnetic NDT to characterize usage properties of flat steel products - Part 3

Energy Technology Data Exchange (ETDEWEB)

Altpeter, I.; Dobmann, G.; Szielasko, K., E-mail: iab.altlau@t-online.de, E-mail: gerd.dobmann@t-online.de, E-mail: klaus.szielasko@izfp.fraunhofer.de [Fraunhofer Inst. - IZFP, Saarbruecken (Germany)

2015-11-15

The Fraunhofer Institute for Nondestructive Testing (IZFP) in Saarbruecken, Germany, started its activities in materials characterization of flat steel products in the eighties of the last century in the basic program of the European Community of Coal and Steel (ECCS). Throughout the years, continuous research and development were performed. The objective of the work, presented within this three-part series of reports, is to discuss the history of an innovation that began in 1988 with R&D in the area of texture characterization in steel sheets produced for car-body manufacturing (Part 1). In the following years the activities were to automate online property determination in terms of yield strength, tensile strength, planar- and vertical-anisotropy factors. Again, steel sheets were the focus of the developments and first NDT systems came into industrial application. Parallel research was performed to characterize the mechanical properties and hardness on heavy steel plates, mainly produced for pipeline manufacturing and offshore applications (Part 2). The final report in the series (Part 3) discusses steel sheet characterization and presents the successful development of a combination transducer that combines ultrasonics with electromagnetic NDT. (author)

Electromagnetic NDT to characterize usage properties of flat steel products - Part 2

Energy Technology Data Exchange (ETDEWEB)

Altpeter, I.; Dobmann, G.; Szielasko, K., E-mail: iab.altlau@t-online.de, E-mail: gerd.dobmann@t-online.de, E-mail: klaus.szielasko@izfp.fraunhofer.de [Fraunhofer Inst. - IZFP, Saarbruecken (Germany)

2015-09-15

The Fraunhofer Institute for Non-destructive Testing (IZFP) in Saarbruecken, Germany, started its activities in materials characterization of flat steel products in the eighties of the last century in the basic program of the European Community of Coal and Steel (ECCS). Throughout the years, continuous research and development were performed. The objective of the work, presented within this three-part series of reports, is to discuss the history of an innovation which began in 1988 with R&D in the area of texture characterization in steel sheets produced for car-body manufacturing (Part 1). In the following years the activities were to automate online property determination in terms of yield strength, tensile strength, planar, and vertical-anisotropy-factors. Again, steel sheets were the focus of the developments and the first NDT systems that came into industrial application for this project. Parallel research was performed to characterize the mechanical properties and hardness of heavy steel plates, mainly produced for pipeline manufacturing and off-shore applications (Part 2) The final report in the series (Part 3) will discuss steel sheet characterization and presents the successful development of a combination-transducer which combines ultrasonics with electromagnetic NDT. (author)

Power properties of invariant tests for spatial autocorrelation in linear regression

NARCIS (Netherlands)

Martellosio, F.

2006-01-01

Many popular tests for residual spatial autocorrelation in the context of the linear regression model belong to the class of invariant tests. This paper derives a number of exact properties of the power function of such tests. In particular, we extend the work of Krämer (2005, Journal of Statistical

Smoke production in fires

Energy Technology Data Exchange (ETDEWEB)

Sarvaranta, L.; Kokkala, M. [VTT Building Technology, Espoo (Finland). Building Physics, Building Services and Fire Technology

1995-12-31

Characterization of smoke, factors influencing smoke production and experimental methods for measuring smoke production are discussed in this literature review. Recent test-based correlation models are also discussed. Despite the large number of laboratories using different fire testing methods, published smoke data have been scarce. Most technical literature on smoke production from building materials is about experimental results in small scale tests. Compilations from cone calorimeter tests have been published for a few materials, e.g. upholstered furniture materials and some building products. Mass optical density data and compilations of gravimetric soot data are available for various materials as well as a number of smoke obscuration values. For a given material often a wide range of values of smoke output can be found in the literature and care should be exercised in applying the appropriate value in each case. In laboratory experiments, the production of smoke and its optical properties are often measured simultaneously with other fire properties as heat release and flame spread. The measurements are usually dynamic in full scale, i.e. they are performed in a flow-through system. In small scale they may be either dynamic, as in the cone calorimeter, or static, i.e. the smoke is accumulated in a closed box. Small-scale tests are necessary as practical tools. Full-scale tests are generally considered to be more reliable and are needed to validitate the small-scale tests

Smoke production in fires

Energy Technology Data Exchange (ETDEWEB)

Sarvaranta, L; Kokkala, M [VTT Building Technology, Espoo (Finland). Building Physics, Building Services and Fire Technology

1996-12-31

Characterization of smoke, factors influencing smoke production and experimental methods for measuring smoke production are discussed in this literature review. Recent test-based correlation models are also discussed. Despite the large number of laboratories using different fire testing methods, published smoke data have been scarce. Most technical literature on smoke production from building materials is about experimental results in small scale tests. Compilations from cone calorimeter tests have been published for a few materials, e.g. upholstered furniture materials and some building products. Mass optical density data and compilations of gravimetric soot data are available for various materials as well as a number of smoke obscuration values. For a given material often a wide range of values of smoke output can be found in the literature and care should be exercised in applying the appropriate value in each case. In laboratory experiments, the production of smoke and its optical properties are often measured simultaneously with other fire properties as heat release and flame spread. The measurements are usually dynamic in full scale, i.e. they are performed in a flow-through system. In small scale they may be either dynamic, as in the cone calorimeter, or static, i.e. the smoke is accumulated in a closed box. Small-scale tests are necessary as practical tools. Full-scale tests are generally considered to be more reliable and are needed to validitate the small-scale tests

Dominant lactic acid bacteria and their technological properties isolated from the Himalayan ethnic fermented milk products.

Science.gov (United States)

Dewan, Sailendra; Tamang, Jyoti Prakash

2007-10-01

Ethnic people of the Himalayan regions of India, Nepal, Bhutan and China consume a variety of indigenous fermented milk products made from cows milk as well as yaks milk. These lesser-known ethnic fermented foods are dahi, mohi, chhurpi, somar, philu and shyow. The population of lactic acid bacteria (LAB) ranged from 10(7) to 10(8) cfu/g in these Himalayan milk products. A total of 128 isolates of LAB were isolated from 58 samples of ethnic fermented milk products collected from different places of India, Nepal and Bhutan. Based on phenotypic characterization including API sugar test, the dominant lactic acid bacteria were identified as Lactobacillus bifermentans, Lactobacillus paracasei subsp. pseudoplantarum, Lactobacillus kefir, Lactobacillus hilgardii, Lactobacillus alimentarius, Lactobacillus paracasei subsp. paracasei, Lactobacillus plantarum, Lactococcus lactis subsp. lactis, Lactococcus lactis subsp. cremoris and Enterococcus faecium. LAB produced a wide spectrum of enzymes and showed high galactosidase, leucine-arylamidase and phosphatase activities. They showed antagonistic properties against selected Gram-negative bacteria. None of the strains produced bacteriocin and biogenic amines under the test conditions used. Most strains of LAB coagulated skim milk with a moderate drop in pH. Some strains of LAB showed a high degree of hydrophobicity, suggesting these strains may have useful adhesive potential. This paper is the first report on functional lactic acid bacterial composition in some lesser-known ethnic fermented milk products of the Himalayas.

A Review of Material Properties Estimation Using Eddy Current Testing and Capacitor Imaging

Directory of Open Access Journals (Sweden)

Mohd. Amri Yunus

2009-01-01

Full Text Available he non destructive testing applications based on inductive (eddy current testing and capacitive sensors are widely used for imaging of material properties. The simple structure, safe to use, low cost, non contact application, good response at medium range frequency of the sensors make them preferable to be used in the industries. The aim of this study is to talk about the material properties estimation applications using eddy current testing and capacitive sensing. The basic operations of eddy current testing and capacitive sensing with example of application in the non destructive testing are discussed. Next, the recent advancements of eddy current testing and capacitive testing in imaging technique are presented in this paper.

Out-of-pile demonstration test of hydrogen production system coupling with HTTR

International Nuclear Information System (INIS)

Inagaki, Yoshiyuki; Nishihara, Tetsuo; Takeda, Tetsuaki; Hada, Kazuhiko; Hayashi, Koji

1999-01-01

In Japan Atomic Energy Research Institute, a hydrogen production system is being designed to produce hydrogen by means of a steam reforming process of natural gas using nuclear heat (10 MW, 905degC) supplied by the High Temperature Engineering Test Reactor (HTTR). The safety principle and criteria are also being investigated in the HTTR hydrogen production system. Prior to coupling of the steam reforming system with the HTTR, an out-of-pile demonstration test was planned to confirm safety, controllability and performance of the steam reforming system under simulated operational conditions of the HTTR hydrogen production system. The out-of-pile test facility simulates key components downstream an intermediate heat exchanger of the HTTR hydrogen production system on a scale of 1 to 30 has a hydrogen production capacity of 110 Nm 3 /h using an electric heater as a reactor substitute. The test facility is under manufacturing aiming at completion in 2000 and followed by the test till 2004. In parallel to this, a hydrogen permeation test and a corrosion test of a catalyst tube of a steam reformer are being carried out to obtain data necessary for the design of the system. This report describes outline of the out-of-pile hydrogen production facility and demonstration test program for the HTTR hydrogen production system at present status. (author)

Out-of-pile demonstration test of hydrogen production system coupling with HTTR

Energy Technology Data Exchange (ETDEWEB)

Inagaki, Yoshiyuki; Nishihara, Tetsuo; Takeda, Tetsuaki; Hada, Kazuhiko; Hayashi, Koji [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment

1999-07-01

In Japan Atomic Energy Research Institute, a hydrogen production system is being designed to produce hydrogen by means of a steam reforming process of natural gas using nuclear heat (10 MW, 905degC) supplied by the High Temperature Engineering Test Reactor (HTTR). The safety principle and criteria are also being investigated in the HTTR hydrogen production system. Prior to coupling of the steam reforming system with the HTTR, an out-of-pile demonstration test was planned to confirm safety, controllability and performance of the steam reforming system under simulated operational conditions of the HTTR hydrogen production system. The out-of-pile test facility simulates key components downstream an intermediate heat exchanger of the HTTR hydrogen production system on a scale of 1 to 30 has a hydrogen production capacity of 110 Nm{sup 3}/h using an electric heater as a reactor substitute. The test facility is under manufacturing aiming at completion in 2000 and followed by the test till 2004. In parallel to this, a hydrogen permeation test and a corrosion test of a catalyst tube of a steam reformer are being carried out to obtain data necessary for the design of the system. This report describes outline of the out-of-pile hydrogen production facility and demonstration test program for the HTTR hydrogen production system at present status. (author)

Standard test method for creep-fatigue testing

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This test method covers the determination of mechanical properties pertaining to creep-fatigue deformation or crack formation in nominally homogeneous materials, or both by the use of test specimens subjected to uniaxial forces under isothermal conditions. It concerns fatigue testing at strain rates or with cycles involving sufficiently long hold times to be responsible for the cyclic deformation response and cycles to crack formation to be affected by creep (and oxidation). It is intended as a test method for fatigue testing performed in support of such activities as materials research and development, mechanical design, process and quality control, product performance, and failure analysis. The cyclic conditions responsible for creep-fatigue deformation and cracking vary with material and with temperature for a given material. 1.2 The use of this test method is limited to specimens and does not cover testing of full-scale components, structures, or consumer products. 1.3 This test method is primarily ...

Toxicity and physical properties of atrazine and its degradation products: A literature survey

Energy Technology Data Exchange (ETDEWEB)

Pugh, K.C.

1994-10-01

The Tennessee Valley Authority`s Environmental Research Center has been developing a means of detoxifying atrazine waste waters using TiO{sub 2} photocatalysis. The toxicity and physical properties of atrazine and its degradation products will probably be required information in obtaining permits from the United States Environmental Protection Agency for the demonstration of any photocatalytic treatment of atrazine waste waters. The following report is a literature survey of the toxicological and physical properties of atrazine and its degradation products.

76 FR 69481 - Testing and Labeling Pertaining to Product Certification

Science.gov (United States)

2011-11-08

... 1107 Testing and Labeling Pertaining to Product Certification; Final Rule #0;#0;Federal Register / Vol... Pertaining to Product Certification AGENCY: Consumer Product Safety Commission. ACTION: Final rule. SUMMARY... that the product complies with the certification requirements under section 14(a) of the Consumer...

76 FR 2930 - Market Test of Experimental Product: “Gift Cards”

Science.gov (United States)

2011-01-18

... POSTAL SERVICE Market Test of Experimental Product: ``Gift Cards'' AGENCY: Postal Service \\TM\\. ACTION: Notice. SUMMARY: The Postal Service gives notice of a market test of an experimental product in... notice pursuant to 39 U.S.C. 3641(c)(1) that it will begin a market test of its ``Gift Cards...

Design and Testing of Subsystems for Mo-99 Production

Energy Technology Data Exchange (ETDEWEB)

Gromov, R. [Argonne National Lab. (ANL), Argonne, IL (United States); Bailey, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Virgo, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Chemerisov, S. [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, G. F. [Argonne National Lab. (ANL), Argonne, IL (United States)

2017-01-01

Argonne National Laboratory, in cooperation with Los Alamos National Laboratory, is developing technology with NorthStar Medical Technologies to produce ⁹⁹Mo from the γ,n reaction on a ¹⁰⁰Mo target in an electron accelerator. During production runs and thermal testing of the helium-cooled target, it became obvious that a production-scale beam-line configuration would need a collimator to protect the target from accidental beam misplacement or a beam-profile change. A prototype high-power collimator and beam stop were designed and fabricated. Testing indicated that they will be able to operate at full power in the production-scale accelerator.

26 CFR 1.1031(a)-1 - Property held for productive use in trade or business or for investment.

Science.gov (United States)

2010-04-01

....1031(a)-1 Property held for productive use in trade or business or for investment. (a) In general—(1... business or for investment is exchanged solely for property of a like kind to be held either for productive use in a trade or business or for investment. Under section 1031(a)(1), property held for productive...

Automatic test comes to focal plane array production

Science.gov (United States)

Skaggs, Frank L.; Barton, T. D.

1992-08-01

To meet the needs of military and commercial markets, the infrared focal plane array industry must develop new, effective and low cost methods of fabricating and testing imaging detectors. This paper describes Texas Instruments new concepts in automated testing and cold probe technology as they apply to volume production.

A comparative study of zinc protoporphyrin IX-forming properties of animal by-products as sources for improving the color of meat products.

Science.gov (United States)

Wakamatsu, Jun-ichi; Murakami, Naoko; Nishimura, Takanori

2015-05-01

The objective of this study was to obtain fundamental data for improving the color of meat products by using animal by-products. We investigated zinc protoporphyrin IX (ZnPP)-forming properties of various internal organs from pigs and chickens. ZnPP was formed in the liver, heart and kidney, whereas the porcine spleen and bile, which are involved in the metabolism of heme, did not have ZnPP-forming properties. The optimum pH values were different among the internal organs and the ZnPP-forming properties of porcine organs were better than those of chicken organs. The porcine liver showed the greatest ZnPP-forming properties among all of the internal organs investigated in this study. The optimum pH value for ZnPP formation in the liver was lower than that of skeletal muscle. Oxygen did not inhibit the formation of ZnPP in the liver, unlike in skeletal muscle. Animal by-products such as the liver have good ability for the formation of ZnPP and might be useful for improving the color of meat products. © 2014 Japanese Society of Animal Science.

Mechanical properties test program on structural materials in a sodium environment

International Nuclear Information System (INIS)

Natesan, K.; Chopra, O.K.; Kassner, T.F.

1979-10-01

This document describes in detail the ongoing and planned US Test program on the mechanical properties of sodium-exposed Type 316 austenitic stainless and Fe-2 1/4 Cr-1 Mo ferritic steels. The test program is based on the Development Requirement Specifications (DRS) established by the DOE/Clinch River Breeder Reactor Project (CRBRP) Program Office, the general need for the development of LMFBR structural-design criteria established by the Nuclear Systems Materials Handbook, and the need for a fundamental understanding of materials behavior in a sodium environment, which is generic to LMFBR systems. The planned test program is an extension of work based on current knowledge of sodium chemistry and the influence of sodium purity on the mechanical properties of structural materials

Mechanical properties test data of Alloy 718 for liquid metal fast breeder reactor applications

International Nuclear Information System (INIS)

Korth, G.E.

1983-01-01

Mechanical property test data are reported for Alloy 718 with two heat treatments: conventional heat treatment (CHT) for base metal and Idaho National Engineering Laboratory (INEL) heat treatment (IHT) for base and weld metal. Tests were conducted in air from 24 to 704 degree C and include elastic properties (Young's modulus, shear modulus, Poisson's ratio), tensile properties, creep-rupture properties, fatigue properties, creep-fatigue properties, and Charpy impact behavior. Effects of long term thermal aging at 538, 593, 649, and 704 degree C for times to 25,000 h are also reported for CHT material (tensile, creep-rupture, fatigue, and Charpy), and IHT material (tensile, and Charpy). 18 refs., 63 figs., 36 tabs

Comparison of simulants to actual neutralized current acid waste: process and product testing of three NCAW core samples from Tanks 101-AZ and 102-AZ

Energy Technology Data Exchange (ETDEWEB)

Morrey, E.V.; Tingey, J.M.; Elliott, M.L.

1996-10-01

A vitrification plant is planned to process the high-level waste (HLW) solids from Hanford Site tanks into canistered glass logs for disposal in a national repository. Programs were established within the Pacific Northwest Laboratory Vitrification Technology Development (PVTD) Project to test and model simulated waste to support design, feed processability, operations, permitting, safety, and waste-form qualification. Parallel testing with actual radioactive waste was performed on a laboratory-scale to confirm the validity of using simulants and glass property models developed from simulants. Laboratory-scale testing has been completed on three radioactive core samples from tanks 101-AZ and 102-AZ containing neutralized current acid waste (NCAW), which is one of the first waste types to be processed in the high-level waste vitrification plant under a privatization scenario. Properties of the radioactive waste measured during process and product testing were compared to simulant properties and model predictions to confirm the validity of simulant and glass property ,models work. This report includes results from the three NCAW core samples, comparable results from slurry and glass simulants, and comparisons to glass property model predictions.

Comparison of simulants to actual neutralized current acid waste: Process and product testing of three NCAW core samples from Tanks 101-AZ and 102-AZ

Energy Technology Data Exchange (ETDEWEB)

Morrey, E.V.; Tingey, J.M.

1996-04-01

A vitrification plant is planned to process the high-level waste (HLW) solids from Hanford Site tanks into canistered glass logs for disposal in a national repository. Programs have been established within the Pacific Northwest Laboratory Vitrification Technology Development (PVTD) Project to test and model simulated waste to support design, feed processability, operations, permitting, safety, and waste-form qualification. Parallel testing with actual radioactive waste is being performed on a laboratory-scale to confirm the validity of using simulants and glass property models developed from simulants. Laboratory-scale testing has been completed on three radioactive core samples from tanks 101-AZ and 102-AZ containing neutralized current acid waste (NCAW), which is one of the first waste types to be processed in the high-level waste vitrification plant under a privatization scenario. Properties of the radioactive waste measured during process and product testing were compared to simulant properties and model predictions to confirm the validity of simulant and glass property models work. This report includes results from the three NCAW core samples, comparable results from slurry and glass simulants, and comparisons to glass property model predictions.

Comparison of simulants to actual neutralized current acid waste: process and product testing of three NCAW core samples from Tanks 101-AZ and 102-AZ

International Nuclear Information System (INIS)

Morrey, E.V.; Tingey, J.M.; Elliott, M.L.

1996-10-01

A vitrification plant is planned to process the high-level waste (HLW) solids from Hanford Site tanks into canistered glass logs for disposal in a national repository. Programs were established within the Pacific Northwest Laboratory Vitrification Technology Development (PVTD) Project to test and model simulated waste to support design, feed processability, operations, permitting, safety, and waste-form qualification. Parallel testing with actual radioactive waste was performed on a laboratory-scale to confirm the validity of using simulants and glass property models developed from simulants. Laboratory-scale testing has been completed on three radioactive core samples from tanks 101-AZ and 102-AZ containing neutralized current acid waste (NCAW), which is one of the first waste types to be processed in the high-level waste vitrification plant under a privatization scenario. Properties of the radioactive waste measured during process and product testing were compared to simulant properties and model predictions to confirm the validity of simulant and glass property ,models work. This report includes results from the three NCAW core samples, comparable results from slurry and glass simulants, and comparisons to glass property model predictions

Comparison of simulants to actual neutralized current acid waste: Process and product testing of three NCAW core samples from Tanks 101-AZ and 102-AZ

International Nuclear Information System (INIS)

Morrey, E.V.; Tingey, J.M.

1996-04-01

A vitrification plant is planned to process the high-level waste (HLW) solids from Hanford Site tanks into canistered glass logs for disposal in a national repository. Programs have been established within the Pacific Northwest Laboratory Vitrification Technology Development (PVTD) Project to test and model simulated waste to support design, feed processability, operations, permitting, safety, and waste-form qualification. Parallel testing with actual radioactive waste is being performed on a laboratory-scale to confirm the validity of using simulants and glass property models developed from simulants. Laboratory-scale testing has been completed on three radioactive core samples from tanks 101-AZ and 102-AZ containing neutralized current acid waste (NCAW), which is one of the first waste types to be processed in the high-level waste vitrification plant under a privatization scenario. Properties of the radioactive waste measured during process and product testing were compared to simulant properties and model predictions to confirm the validity of simulant and glass property models work. This report includes results from the three NCAW core samples, comparable results from slurry and glass simulants, and comparisons to glass property model predictions

Development of an ASTM standard glass durability test, the Product Consistency Test (PCT), for high level radioactive waste glass

International Nuclear Information System (INIS)

Jantzen, C.M.; Bibler, N.E.; Beam, D.C.; Ramsey, W.G.

1994-01-01

The nation's first, and the world's largest, facility to immobilize high-level nuclear waste in durable borosilicate glass has started operation at the Savannah River Site (SRS) in Aiken, South Carolina. The product specifications on the glass wasteform produced in the Defense Waste Processing Facility (DWPF) required extensive characterization of the glass product before actual production began and for continued characterization during production. To aid in this characterization, a glass durability (leach) test was needed that was easily reproducible, could be performed remotely on highly radioactive samples, and could yield results rapidly. Several standard leach tests were examined with a variety of test configurations. Using existing tests as a starting point, the DWPF Product Consistency Test (PCT was developed in which crushed glass samples are exposed to 90 ± 2 degree C deionized water for seven days. Based on extensive testing, including a seven-laboratory round robin and confirmatory testing with radioactive samples, the PCT is very reproducible, yields reliable results rapidly, and can be performed in shielded cell facilities with radioactive samples

Psychometric Properties of Raw and Scale Scores on Mixed-Format Tests

Science.gov (United States)

Kolen, Michael J.; Lee, Won-Chan

2011-01-01

This paper illustrates that the psychometric properties of scores and scales that are used with mixed-format educational tests can impact the use and interpretation of the scores that are reported to examinees. Psychometric properties that include reliability and conditional standard errors of measurement are considered in this paper. The focus is…

75 FR 28335 - Testing and Labeling Pertaining to Product Certification

Science.gov (United States)

2010-05-20

... Product Certification; Proposed Rule #0;#0;Federal Register / Vol. 75, No. 97 / Thursday, May 20, 2010.... CPSC-2010-0038] RIN 3041-AC71 Testing and Labeling Pertaining to Product Certification AGENCY: Consumer... also address labeling of consumer products to show that the product complies with certification...

Expansion and functional properties of extruded snacks enriched with nutrition sources from food processing by-products.

Science.gov (United States)

Korkerd, Sopida; Wanlapa, Sorada; Puttanlek, Chureerat; Uttapap, Dudsadee; Rungsardthong, Vilai

2016-01-01

Rich sources of protein and dietary fiber from food processing by-products, defatted soybean meal, germinated brown rice meal, and mango peel fiber, were added to corn grit at 20 % (w/w) to produce fortified extruded snacks. Increase of total dietary fiber from 4.82 % (wb) to 5.92-17.80 % (wb) and protein from 5.03 % (wb) to 5.46-13.34 % were observed. The product indicated high expansion and good acceptance tested by sensory panels. There were 22.33-33.53 and 5.30-11.53 fold increase in the phenolics and antioxidant activity in the enriched snack products. The effects of feed moisture content, screw speed, and barrel temperature on expansion and nutritional properties of the extruded products were investigated by using response surface methodology. Regression equations describing the effect of each variable on the product responses were obtained. The snacks extruded with feed moisture 13-15 % (wb) and extrusion temperature at 160-180 °C indicated the products with high preference in terms of expansion ratio between insoluble dietary fiber and soluble dietary fiber balance. The results showed that the by-products could be successfully used for nutritional supplemented expanded snacks.

46 CFR 154.182 - Contiguous hull structure: Production weld test.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Contiguous hull structure: Production weld test. 154.182... Equipment Hull Structure § 154.182 Contiguous hull structure: Production weld test. If a portion of the contiguous hull structure is designed for a temperature colder than −34 °C (−30 °F) and is not part of the...

Testing of the Structure and Mechanical Properties of Technical Titanium Joints

Directory of Open Access Journals (Sweden)

Bogumił Wronka

2013-01-01

Full Text Available The aim of the research was the titanium pipeline welding technology. The transformations of this material due to the influence of thermal welding were analysed. The basic purpose was to evaluate the properties of titanium joint areas. Pipe joints of various thicknesses were welded by means of TIG argon arc welding while applying the optimum and reduced gas flow intensities. The structure and mechanical properties of these joints were tested. Different test results were obtained for joints welded in these two conditions. Recommendations concerning the welding technology and the heat treatment of joints after welding were presented.

Regional and depth variability of porcine meniscal mechanical properties through biaxial testing.

Science.gov (United States)

Kahlon, A; Hurtig, M B; Gordon, K D

2015-01-01

The menisci in the knee joint undergo complex loading in-vivo resulting in a multidirectional stress distribution. Extensive mechanical testing has been conducted to investigate the tissue properties of the knee meniscus, but the testing conditions do not replicate this complex loading regime. Biaxial testing involves loading tissue along two different directions simultaneously, which more accurately simulates physiologic loading conditions. The purpose of this study was to report mechanical properties of meniscal tissue resulting from biaxial testing, while simultaneously investigating regional variations in properties. Ten left, fresh porcine joints were obtained, and the medial and lateral menisci were harvested from each joint (twenty menisci total). Each menisci was divided into an anterior, middle and posterior region; and three slices (femoral, deep and tibial layers) were obtained from each region. Biaxial and constrained uniaxial testing was performed on each specimen, and Young's moduli were calculated from the resulting stress strain curves. Results illustrated significant differences in regional mechanical properties, with the medial anterior (Young's modulus (E)=11.14 ± 1.10 MPa), lateral anterior (E=11.54 ± 1.10 MPa) and lateral posterior (E=9.0 ± 1.2 MPa) regions exhibiting the highest properties compared to the medial central (E=5.0 ± 1.22 MPa), medial posterior (E=4.16 ± 1.13 MPa) and lateral central (E=5.6 ± 1.20 MPa) regions. Differences with depth were also significant on the lateral meniscus, with the femoral (E=12.7 ± 1.22 MPa) and tibial (E=8.6 ± 1.22 MPa) layers exhibiting the highest Young's moduli. This data may form the basis for future modeling of meniscal tissue, or may aid in the design of synthetic replacement alternatives. Copyright © 2014 Elsevier Ltd. All rights reserved.

GPR Laboratory Tests For Railways Materials Dielectric Properties Assessment

Directory of Open Access Journals (Sweden)

Francesca De Chiara

2014-10-01

Full Text Available In railways Ground Penetrating Radar (GPR studies, the evaluation of materials dielectric properties is critical as they are sensitive to water content, to petrographic type of aggregates and to fouling condition of the ballast. Under the load traffic, maintenance actions and climatic effects, ballast condition change due to aggregate breakdown and to subgrade soils pumping, mainly on existing lines with no sub ballast layer. The main purpose of this study was to validate, under controlled conditions, the dielectric values of materials used in Portuguese railways, in order to improve the GPR interpretation using commercial software and consequently the management maintenance planning. Different materials were tested and a broad range of in situ conditions were simulated in laboratory, in physical models. GPR tests were performed with five antennas with frequencies between 400 and 1800 MHz. The variation of the dielectric properties was measured, and the range of values that can be obtained for different material condition was defined. Additionally, in situ GPR measurements and test pits were performed for validation of the dielectric constant of clean ballast. The results obtained are analyzed and the main conclusions are presented herein.

Improved concrete properties to resist the saline water using environmental by-product

Directory of Open Access Journals (Sweden)

Mohamed Anwar

2013-10-01

Full Text Available This paper investigates the influence of using environmental by-product materials (silica fume and fly ash in concrete on the chloride ion permeability of concrete. Nine concrete mixtures were designed to have the same degree of workability and air content with water/cementitious material ratio of 0.4. The studied parameters include the main fresh and hardened concrete properties such as slump, air content, unit weight, compressive strength, tensile strength, flexural strength, static Young's modulus, and dynamic elastic modulus. Concrete samples were kept in water for 28 days, then immersed in artificial sea water for 5 months. The total and soluble chloride contents were measured through the concrete using the potentiometric titration analysis. The obtained test results indicated that the use of ternary systems in concrete improved the different characteristics of the product concrete and showed a significant resistance to chloride penetration. The weights of chloride in mix 9 (10% silica fume and 25% fly ash at depths from the concrete surface to 30 mm were less than the weights of control mix 1 (100% ordinary Portland cement by about 60%. Further, the ternary systems can be used in concrete industry with considerable proportions.

Measurement of production and properties of jets at the CERN anti pp collider

International Nuclear Information System (INIS)

Bagnaia, P.; Bonaudi, F.; Borghini, M.; Clark, A.G.; Darriulat, P.; Lella, L. di; Dorsaz, P.A.; Froidevaux, D.; Gildemeister, O.; Hansen, J.R.; Himel, T.; Hungerbuehler, V.; Jenni, P.; Mapelli, L.; Onions, C.; Rothenberg, A.; Siegrist, J.L.; Steiner, H.M.; Stimpfl, G.; Weidberg, A.; Banner, M.; Bloch, P.; Lancon, E.; Loucatos, S.; Mansoulie, B.; Polverel, M.; Roussarie, A.; Teiger, J.; Zaccone, H.; Battiston, R.; Mantovani, G.C.; Dines-Hansen, J.; Kofoed-Hansen, O.; Madsen, B.; Moellerud, R.; Hansen, P.; Livan, M.; Parrour, G.; Plothow-Besch, H.; Paris-11 Univ., 91 - Orsay; Pastore, F.

1983-01-01

The production and properties of high transverse momentum hadron jets have been measured in the UA2 experiment at the CERN anti pp Colider (√s=540 GeV) using a highly segmented total absorption calorimeter. The characteristics of a sample of two-jet events with invariant mass up to 200 GeV/c 2 are discussed, including measurements of their fragmentation properties, angular and rapidity distributions, and the properties of the additional energy clusters accompanying the two-jet system. Cross sections for inclusive jet production in the jet transverse momentum range between 30 and 100 GeV/c and for the two-jet invariant mass distribution in the mass range from 60-200 GeV/c 2 are reported. (orig.)

Test elements of direct sums and free products of free Lie algebras

Indian Academy of Sciences (India)

Abstract. We give a characterization of test elements of a direct sum of free Lie algebras in terms of test elements of the factors. In addition, we construct certain types of test elements and we prove that in a free product of free Lie algebras, product of the homogeneous test elements of the factors is also a test element.

Test elements of direct sums and free products of free Lie algebras

Indian Academy of Sciences (India)

We give a characterization of test elements of a direct sum of free Lie algebras in terms of test elements of the factors. In addition, we construct certain types of test elements and we prove that in a free product of free Lie algebras, product of the homogeneous test elements of the factors is also a test element.

Generating and testing methods for consumer-oriented product development

International Nuclear Information System (INIS)

2001-10-01

In order to obtain a good insight into various design methods that can be used by product developers to enable them to develop and test useful domotics products (domotics: intelligent systems for the home), an inventory has been made of the methods used in the Netherlands. The inventory is directed at two categories of methods: (1) Methods of getting better acquainted with the user and/or the problem, and of generating novel solutions: generative methods; and (2) Methods of assessing solutions (through various phases of the designing process): testing methods. The first category of methods concentrates on the designing process. In other words: how can the designer realise as much as possible of the workability of (domotics) products during the designing process? The second category aims at testing a design (in whatever shape: drawing, prototype, functional computer animation, etc.) through its users. These are methods of assessing a design at various stages of the designing process [nl

46 CFR 164.023-13 - Production tests and inspections.

Science.gov (United States)

2010-10-01

... Constant Rate of Traverse tensile testing machine, capable of initial clamp separation of ten inches and a... production testing on a lot must meet the following criteria for the lot to be shipped as Coast Guard... the acceptance testing values but not less than the performance minimums. (2) Length/weight values...

Entanglement property in matrix product spin systems

International Nuclear Information System (INIS)

Zhu Jingmin

2012-01-01

We study the entanglement property in matrix product spin-ring systems systemically by von Neumann entropy. We find that: (i) the Hilbert space dimension of one spin determines the upper limit of the maximal value of the entanglement entropy of one spin, while for multiparticle entanglement entropy, the upper limit of the maximal value depends on the dimension of the representation matrices. Based on the theory, we can realize the maximum of the entanglement entropy of any spin block by choosing the appropriate control parameter values. (ii) When the entanglement entropy of one spin takes its maximal value, the entanglement entropy of an asymptotically large spin block, i.e. the renormalization group fixed point, is not likely to take its maximal value, and so only the entanglement entropy S n of a spin block that varies with size n can fully characterize the spin-ring entanglement feature. Finally, we give the entanglement dynamics, i.e. the Hamiltonian of the matrix product system. (author)

Microbial alkaline proteases: Optimization of production parameters and their properties

Directory of Open Access Journals (Sweden)

Kanupriya Miglani Sharma

2017-06-01

Full Text Available Proteases are hydrolytic enzymes capable of degrading proteins into small peptides and amino acids. They account for nearly 60% of the total industrial enzyme market. Proteases are extensively exploited commercially, in food, pharmaceutical, leather and detergent industry. Given their potential use, there has been renewed interest in the discovery of proteases with novel properties and a constant thrust to optimize the enzyme production. This review summarizes a fraction of the enormous reports available on various aspects of alkaline proteases. Diverse sources for isolation of alkaline protease producing microorganisms are reported. The various nutritional and environmental parameters affecting the production of alkaline proteases in submerged and solid state fermentation are described. The enzymatic and physicochemical properties of alkaline proteases from several microorganisms are discussed which can help to identify enzymes with high activity and stability over extreme pH and temperature, so that they can be developed for industrial applications.

STUDYING THE PROPERTIES OF QUARK PRODUCTS WITH COMPONENTS OF PLANT ORIGIN

Directory of Open Access Journals (Sweden)

L. V. Golubeva

2015-01-01

Full Text Available The technology of curd product with the addition of pine nuts and honey (pine nuts and fructose. It is necessary to examine the fatty acid and vitamin composition of cottage cheese products, as well as conduct research component of the antioxidant properties of vegetable origin. Composition pine nuts unique. High oil is 63.9% of the core. When making pine nuts in curd product is enriched with the latest oil. The main difference vegetable fat (oil of the animal higher content of unsaturated fatty acids. They cannot be formed in the human body and must be ingested with food. Held production curd cottage cheese product based on different mass fraction of fat. The relation of animal and vegetable oils in samples of cheese products: № 1 0.15: 1, № 2 1.3: 1, № 3 2.32: 1. The optimum ratio of animal and vegetable fats in the diet of modern man 70: 30, that is, the total number of entering the body fat (100-105 grams per day of animal fats should be 70-75 g and vegetable – 30 g. Closest to the recommended norm ratio of animal and vegetable fats was the sample № 2. Sample number 1 and 3 further enriched vegetable fats, which also has a positive effect on curd products. Found an increase in the mass fraction of fat-soluble vitamins. The amount of vitamin E in the curd product increased 6 times in comparison with the cheese without additives. Studied the antioxidant properties of pine nuts. Determined the antioxidant activity of 3.92 mg / dm3 . Found that cheese product is rich in vitamins, antioxidants, and a polynomial-saturated fatty acids.

Entanglement properties of kaons and tests of hidden-variable models

International Nuclear Information System (INIS)

Genovese, M.

2004-01-01

In this paper we discuss entanglement properties of neutral kaons systems and their use for testing local realism. In particular, we analyze a Hardy-type scheme [A. Bramon and G. Garbarino, Phys. Rev. Lett. 89, 160401 (2002)] recently suggested for performing a test of hidden-variable theories against standard quantum mechanics. Our result is that this scheme could, in principle, lead to a conclusive test of local realism, but only if higher identification efficiencies than in today's experiments will be reached

46 CFR 160.077-23 - Production tests and inspections.

Science.gov (United States)

2010-10-01

... fixed anchor, or (C) a tensile test machine that is capable of holding a given tension. The assembly... testing of each incoming lot of inflation chamber material before using that lot in production; (iii) Have... inspector must perform or supervise testing and inspection of at least one PFD lot in each five lots...

DPRK's 4"t"h Nuclear Test and its Tritium Production

International Nuclear Information System (INIS)

Kim, Min Soo; Lee, Sang Joon; Chang, Sun Young

2016-01-01

On January 6, 2016 at 10:30am, the artificial earthquake in the DPRK was detected by multiple international seismic organizations. After 2 hours, the DPRK announced on state TV that 'The first H-bomb test was successfully conducted in the DPRK at 10:00 am on Wednesday, Juche 105(2016), pursuant to the strategic determination of the ruling communist party.' There has been a doubt about the real nature of the DPRK's 4th nuclear test, since 2 months have been passed after its nuclear test. To analyze the nature of the DPRK's nuclear test, it is necessary to check possible options for production of essential materials. The pathways to produce nuclear fusion material (tritium) and to have a relatively high possibility for the DPRK are described in this article. Tritium is key material for H-bomb. And there are two options for the DPRK which are 1) production and 2) illicit trafficking. And this study is focused on production possibility of DPRK. Determination of the nature of DPRK's nuclear test is very hard issue

Development and evaluation of nutritional, sensory and glycemic properties of finger millet (Eleusine coracana L.) based food products.

Science.gov (United States)

Shobana, Shanmugam; Selvi, Ravi Poovizhi; Kavitha, Vasudevan; Gayathri, Nagamuthu; Geetha, Gunasekaran; Gayathri, Rajagopal; Vijayalakshmi, Parthasarthy; Balasubramaniam, K Kandappa Gounder; Ruchi, Vaidya; Sudha, Vasudevan; Anjana, Ranjit Mohan; Unnikrishnan, Ranjit; Malleshi, Nagappa Gurusiddappa; Henry, C Jk; Krishnaswamy, Kamala; Mohan, Viswanathan

2018-01-01

Finger millet (Eleusine coracana L.) (FM) is rich in dietary fibre and is therefore expected to elicit a lower glycemic response compared to other grains. However, there is little data on the glycemic properties of FM-based products. We evaluated the nutritional, sensory and glycemic properties of decorticated millet with lower polish (DFM-LDP), flakes (FMF), vermicelli (FMV) and extruded snack (FMES) (both FMV and FMES with 7-8% added soluble fibre). The nutrient contents of the FM products were evaluated by standard AOAC (Association of Official Analytical Chemists) and AACC (American Association of Cereal Chemists) methods. Sensory evaluation was conducted monadically using a 9-point hedonic scale using untrained panel members. GI testing was conducted using a standardized validated protocol. The study was conducted according to the guidelines laid down by the Declaration of Helsinki, and was approved by the Ethics Committee of the Madras Diabetes Research Foundation. The products had dietary fibre (DF) content between 5.8-15.6 g%. FMES was unique in having a very low fat content (0.17%). Evaluation of sensory perception revealed moderate acceptance of millet based products. The glycemic indices (GI) (mean±SEM) of the products were 84.7±7.7%, 82.3±6.4%, 65.5±5.1% and 65.0±6.6% for DFM-LDP, FMF, FMV and FMES respectively. DFM-LDP and FMF (purely finger millet based products) elicited higher glycemic responses. Comparatively, FMV and FMES (with added functional ingredients) exhibited medium GI values and, are healthier dietary options. It is possible to prepare FM products with lower GI by utilizing functional ingredients.

PHYSICAL PROPERTIES OF KAOLIN/SAND SLURRY USED DURING SUBMERSIBLE MIXER PUMP TESTS AT TNX

International Nuclear Information System (INIS)

HANSEN, ERICH

2005-01-01

The purpose of this task is to characterize the physical properties of the kaolin/sand slurries used during the testing of a new submersible mixer pump (SMP) which had undergone performance testing at the TNX Waste Tank mockup facility from July 2004 through May 2005. During this time period, four identical SMPs were subjected to various water tests and four different tests using different batches of kaolin/sand slurries. The physical properties of the kaolin/sand slurries were measured for three of the four tests. In these tests, three different sample locations were used to pull samples, the SMP cooling water exit (CWE), the SMP fluid flow field (FFF), and SMP effective cleaning radius (ECR). The physical properties measured, though not for each sample, included rheology, weight percent total solids (wt% TS), density, kaolin/sand slurry particle size distribution (PSD), weight percent and particles size distribution of material greater than 45 microns

Transient productivity index for numerical well test simulations

Energy Technology Data Exchange (ETDEWEB)

Blanc, G.; Ding, D.Y.; Ene, A. [Institut Francais du Petrole, Pau (France)] [and others

1997-08-01

The most difficult aspect of numerical simulation of well tests is the treatment of the Bottom Hole Flowing (BHF) Pressure. In full field simulations, this pressure is derived from the Well-block Pressure (WBP) using a numerical productivity index which accounts for the grid size and permeability, and for the well completion. This productivity index is calculated assuming a pseudo-steady state flow regime in the vicinity of the well and is therefore constant during the well production period. Such a pseudo-steady state assumption is no longer valid for the early time of a well test simulation as long as the pressure perturbation has not reached several grid-blocks around the well. This paper offers two different solutions to this problem: (1) The first one is based on the derivation of a Numerical Transient Productivity Index (NTPI) to be applied to Cartesian grids; (2) The second one is based on the use of a Corrected Transmissibility and Accumulation Term (CTAT) in the flow equation. The representation of the pressure behavior given by both solutions is far more accurate than the conventional one as shown by several validation examples which are presented in the following pages.

Production process of a new cellulosic fiber with antimicrobial properties.

Science.gov (United States)

Zikeli, Stefan

2006-01-01

The Lyocell process (system: cellulose-water-N-methylmorpholine oxide) of Zimmer AG offers special advantages for the production of cellulose fibers. The process excels by dissolving the most diverse cellulose types as these are optimally adjusted to the process by applying different pretreatment methods. Based on this stable process, Zimmer AG's objective is to impart to the Lyocell fiber additional value to improve quality of life and thus to tap new markets for the product. Thanks to the specific incorporation of seaweed, the process allows to produce cellulose Lyocell fibers with additional and new features. They are activated in a further step - by specific charging with metal ions - in order to obtain antibacterial properties. The favorable textile properties of fibers produced by the Lyocell process are not adversely affected by the incorporation of seaweed material or by activation to obtain an antibacterial fiber so that current textile products can be made from the fibers thus produced. The antibacterial effect is achieved by metal ion activation of the Lyocell fibers with incorporated seaweed, which contrasts with the antibacterial fibers known so far. Antibacterial fibers produced by conventional methods are in part only surface finished with antibacterially active chemicals or else they are produced by incorporating organic substances with antibacterial and fungicidal effects. Being made from cellulose, the antibacterial Lyocell fiber Sea Cell Active as the basis for quality textiles exhibits a special wear comfort compared to synthetic fibers with antibacterial properties and effects. This justifies the conclusion that the Zimmer Lyocell process provides genuine value added and that it is a springboard for further applications.

Production and properties of the heaviest elements. Status and perspectives

International Nuclear Information System (INIS)

Backe, H.; Hebberger, F.P.; Sewtz, M.; Turler, A.

2007-01-01

This article reviews the following topics which were discussed at the Workshop on the Atomic Properties of the Heaviest Elements held from September 25-27, 2006 in Chiemsee, Germany: (i) the recent progress in the production of the heaviest elements, the investigation of their nuclear structure, and prospects for direct mass measurements in Penning traps; (ii) recent studies of their chemical properties with the aid of volatile species and single-atom aqueous-phase chemistry; (iii) the current status and future prospects for the investigation of atomic and ionic properties such as optical spectroscopy in gas cells and ion traps, including fully relativistic calculations of the atomic level structure with predictions for the element nobelium; and (iv) ionic charge radii measurements in buffer gas filled drift cells, and ion chemical reactions in the gas phase. (authors)

New method to calculate the mechanical properties of unirradiated fuel cladding from ring tensile tests

Energy Technology Data Exchange (ETDEWEB)

Martin-Rengel, M.A. [Departamento de Ciencia de Materiales, UPM, E.T.S.I. Caminos, Canales y Puertos, Profesor Aranguren s/n, E-28040 Madrid (Spain); Consejo de Seguridad Nuclear (CSN), Justo Dorado 11, E-28040 Madrid (Spain); Gomez, F.J.; Ruiz-Hervias, J.; Caballero, L.; Valiente, A. [Departamento de Ciencia de Materiales, UPM, E.T.S.I. Caminos, Canales y Puertos, Profesor Aranguren s/n, E-28040 Madrid (Spain)

2009-06-15

Nuclear fuel cladding is the first barrier used to confine the fuel and the fission products produced during irradiation. Zirconium alloys are used for this purpose due to their remarkable neutron transparency, together with their good mechanical properties at operational temperatures. Consequently, it is very important to be able to characterize the mechanical response of the irradiated cladding. The mechanical behaviour of the material can be modelled as elastoplastic with different stress-strain curves depending on the direction: radial, hoop or longitudinal direction. The ring tensile test has been proposed to determine the mechanical properties of the cladding along the hoop direction. The initial test consisted of applying a force inside the tube, by means of two half cylinders. Later Arsene and Bai [1,2] modified the experimental device to avoid tube bending at the beginning of the test. The same authors proposed a numerical method to obtain the stress-strain curve in the hoop direction from the experimental load versus displacement results and a given friction coefficient between the loading pieces and the sample [3]. This method has been used by different authors [4] with slight modifications. It is based on the existence of two universal curves under small strain hypothesis: the first correlating the hoop strain and the displacement of the loading piece and the second one correlating the hoop stress and the applied load. In this work, a new method to determine the mechanical properties of the cladding from the ring tensile test results is proposed. Non-linear geometry is considered and an iterative procedure is proposed so universal curves are not needed. A stress-strain curve is determined by combining numerical calculations with experimental results in a convergent loop. The two universal curves proposed by Arsene and Bai [3] are substituted by two relationships, one between the equivalent plastic strain in the centre of the specimen ligament and the

Latest Results On Jet Production and Properties from the LHC

CERN Document Server

Jones, G

2012-01-01

Investigations of jets performed by the ATLAS and CMS collaborations using collisions at $\\sqrt{s}$ = 7 TeV are described. To pics of interest are jet performance, production and the precision measurement of their properties. Comparison of the results to theoretical predictions are discussed and areas with poor agreement identified.

Chemical Properties, Decomposition, and Methane Production of Tertiary Relict Plant Litters: Implications for Atmospheric Trace Gas Production in the Early Tertiary

Science.gov (United States)

Yavitt, J. B.; Bartella, T. M.; Williams, C. J.

2006-12-01

Throughout the early Tertiary (ca. 65-38 Ma) Taxodiaceae-dominated (redwood) wetland forests occupied the high latitudes and were circumpolar in their distribution. Many of these forests had high standing biomass with moderate primary productivity. The geographic extent and amount of Tertiary coals and fossil forests throughout Arctic Canada suggests large areas of wetland forests that may have cycled substantial quantities of carbon, particularly methane until they were replaced by cold tolerant Pinus, Picea, and Larix following climatic cooling associated with the Terminal Eocene Event. To test this hypothesis we compared physiochemical properties, decomposition, and trace gas production of litter from extant Metasequoia, Pinus, Picea, and Larix. Initial results from plantation-grown trees indicate Metasequoia litter is a better source of labile organic substrate than pinaceous litter. Metasequoia litter contained the least lignin and highest amounts of water-soluble compounds of the four litter types studied. Analysis of the lignin structure using cupric oxide oxidation indicates that Metasequoia lignin is enriched in 4'-hydroxyacetophenone and 4'- Hydroxy-3'-methoxyacetophenone relative to the pinaceous litter. In a 12-month decomposition study using litterbags, average litter mass loss was greater for Metasequoia litter (62%) compared to the pinaceous species (50%). Moreover, Metasequoia litter incubated under anoxic conditions produced nearly twice as much CO2 (ca. 4.2 umol/g.day) and CH4 (2.1 umol/g.day) as the pinaceous litter (2.4 umol/g.day for CO2; 1.2 umol/g.day for CH4). Our results support the idea of greater decomposability and palatability of Metasequoia litter as compared to Larix, Picea, or Pinus. Provided that the biochemical properties of Metasequoia have remained relatively stable through geologic time, it appears that early Tertiary Metasequoia-dominated wetland forests may have had higher microbial driven trace gas production than the

Evaluating a new test of whole English collocations

DEFF Research Database (Denmark)

Revier, Robert Lee

2009-01-01

in their own right and, as such, feature formal, semantic, and usage properties similar to those borne by single words. Third, the semantic properties of the constituent words that combine to form collocations are likely to play a role in EFL learners' ability to 'produce' English collocations. Forth, testing...... of L2 collocation knowledge needs to focus on the recognition and production of whole collocations. It is this set of assumptions that the new collocation test presented in this chapter is desined to probe. More specifically, the test is designed to assess L2 learners' productive knowledge of whole...

Software Testing and its Relationship to the Context of the Product

Directory of Open Access Journals (Sweden)

Giordano Soares

2011-12-01

Full Text Available Test equipment today have to deal with the growing complexity of the systems under test, while the schedules, budgets and team sizes are not scaled in the same relationship. In addition, the entire test plan cannot be automate and due to time and budget constraints, only a small fraction of all use cases can be covered in the manual tests. For this, the testers must be familiar with the context of the product under test, to design a test plan effective. This article describes the advantages that lead the fact that the testers know the domain of the software product, especially in relation to managing the complexity and problems of selection and prioritization of tests

Hydraulic testing around Room Q: Evaluation of the effects of mining on the hydraulic properties of Salado Evaporites

Energy Technology Data Exchange (ETDEWEB)

Domski, P.S.; Upton, D.T. [INTERA, Inc., Albuquerque, NM (United States); Beauheim, R.L. [Sandia National Laboratories, Albuquerque, NM (United States)

1996-03-01

Room Q is a 109-m-long cylindrical excavation in the Salado Formation at the Waste Isolation Pilot Plant (WIPP) site. Fifteen boreholes were drilled and instrumented around Room Q so that tests could be conducted to determine the effects of room excavation on the hydraulic properties of the surrounding evaporate rocks. Pressure-buildup and pressure-pulse tests were conducted in all of the boreholes before Room Q was mined. The data sets from only eight of the boreholes are adequate for parameter estimation, and five of those are of poor quality. Constant-pressure flow tests and pressure-buildup tests were conducted after Room Q was mined, producing eleven interpretable data sets, including two of poor quality. Pre-mining transmissivities interpreted from the three good-quality data sets ranged from 1 x 10{sup -15} to 5 x 10{sup -14} m{sup 2}/s (permeability-thickness products of 2 x 10{sup -22} to 9 x 10{sup -21} m{sup 3}) for test intervals ranging in length from 0.85 to 1.37 m. Pre-mining average permeabilities, which can be considered representative of undisturbed, far-field conditions, were 6 x 10{sup -20} and 8 x 10{sup -20} m{sup 2} for anhydrite, and 3 x 10{sup -22} m{sup 2} for halite. Post-mining transmissivities interpreted from the good-quality data sets ranged from 1 x 10{sup -16} to 3 x 10{sup -13} m{sup 2}/s (permeability-thickness products of 2 x 10{sup -23} to 5 x 10{sup -20} m{sup 3}). Post-mining average permeabilities for anhydrite ranged from 8 x 10{sup -20} to 1 x 10{sup -19} m{sup 2}. The changes in hydraulic properties and pore pressures that were observed can be attributed to one or a combination of three processes: stress reduction, changes in pore connectivity, and flow towards Room Q. The effects of the three processes cannot be individually quantified with the available data.

Hydraulic testing around Room Q: Evaluation of the effects of mining on the hydraulic properties of Salado Evaporites

International Nuclear Information System (INIS)

Domski, P.S.; Upton, D.T.; Beauheim, R.L.

1996-03-01

Room Q is a 109-m-long cylindrical excavation in the Salado Formation at the Waste Isolation Pilot Plant (WIPP) site. Fifteen boreholes were drilled and instrumented around Room Q so that tests could be conducted to determine the effects of room excavation on the hydraulic properties of the surrounding evaporate rocks. Pressure-buildup and pressure-pulse tests were conducted in all of the boreholes before Room Q was mined. The data sets from only eight of the boreholes are adequate for parameter estimation, and five of those are of poor quality. Constant-pressure flow tests and pressure-buildup tests were conducted after Room Q was mined, producing eleven interpretable data sets, including two of poor quality. Pre-mining transmissivities interpreted from the three good-quality data sets ranged from 1 x 10 -15 to 5 x 10 -14 m 2 /s (permeability-thickness products of 2 x 10 -22 to 9 x 10 -21 m 3 ) for test intervals ranging in length from 0.85 to 1.37 m. Pre-mining average permeabilities, which can be considered representative of undisturbed, far-field conditions, were 6 x 10 -20 and 8 x 10 -20 m 2 for anhydrite, and 3 x 10 -22 m 2 for halite. Post-mining transmissivities interpreted from the good-quality data sets ranged from 1 x 10 -16 to 3 x 10 -13 m 2 /s (permeability-thickness products of 2 x 10 -23 to 5 x 10 -20 m 3 ). Post-mining average permeabilities for anhydrite ranged from 8 x 10 -20 to 1 x 10 -19 m 2 . The changes in hydraulic properties and pore pressures that were observed can be attributed to one or a combination of three processes: stress reduction, changes in pore connectivity, and flow towards Room Q. The effects of the three processes cannot be individually quantified with the available data

Microindentation test for determining mechanical properties of corroded layers of ceramics

International Nuclear Information System (INIS)

Wakui, Takashi; Futakawa, Masatoshi; Tanabe, Yuji; Eto, Motokuni

1999-01-01

Microindentation tests on ceramics (Si-SiC, SiC, Al 2 O 3 and Si 3 N 4 ) immersed in boiling 95 wt% sulfuric acid for 100 or 1000 hours were performed to evaluate the mechanical properties of their corroded layers. The thickness (T) of corroded layer on ceramics was evaluated in terms of characteristic depth (d) which was determined from the point of inflection on the Depth-Load/Depth curve by the microindentation test. The relationship between T and d was found to be given as T nearly equal 10d. Finite element analyses were performed to validate the relationship and to clarify the effects of mechanical properties of corroded layer and the indenter tip radius on the relationship as well. The mechanical properties [Young's modulus (E f ) and yield stress (σ yf )] of corroded layers of Al 2 O 3 and Si 3 N 4 were identified by fitting the predicted Depth-Load/Depth curve to the experimental data. (author)

Routine Testing of Bitumen Binders

Science.gov (United States)

Holý, Michal; Remišová, Eva

2017-12-01

The quality of bituminous binders used in the construction and maintenance of road surfaces is currently assessed by empirical testing based on obtaining one value for specific boundary conditions, which were designed about 100 years ago. Basic empirical tests include the softening point and penetration, but the practice shows that these tests appear to be inadequate. The evaluation of changes of bitumen properties during the production and paving process of bituminous mixture is also important. The paper points out how the "traditional" tests as softening point and penetration and viscosity are sufficient to evaluate properties of bitumen binders.

Information/testing strategy for identification of substances with endocrine disrupting properties

DEFF Research Database (Denmark)

Hass, Ulla; Christiansen, Sofie; Bjerregaard, Poul

This report has been prepared by the Danish Centre on Endocrine Disrupters (CeHoS) as a project contracted by the Danish Environmental Protection Agency. The Danish Centre on Endocrine Disrupters is an interdisciplinary scientific network without walls. The main purpose of the Centre is to build ...... of substances with endocrine disrupting properties under various legislative frameworks, including REACH (EC No 1907/2006), the Plant Protection Products Regulation (PPPR) (EC No 1107/2009) and the Biocidal Products Regulation (BPR) (EC No 528/2012) ....

Comparative product testing of children's restraint systems, with inclusion of side-collision tests

Energy Technology Data Exchange (ETDEWEB)

Goerlitz, H. [Stiftung Warentest, Berlin (Germany); Noeske, V. [DEKRA Dresden (Germany)

2001-07-01

Stiftung Warentest has conducted comparative product testing for Group 0.. III child car seats to evaluate accident protection, handling, comfort of the seats, and safety against faulty use. The tests that were conducted were intended to provide assessment of product quality. Owing to great reader interest, tests conducted on child car seats have become well established for a considerable number of years now. They enjoy esteemed status, for example, in our magazine test. Stiftung Warentest conducted its first tests on children's restraint system many years ago: in May of 1968. The great interest in this topic, as evidenced by widespread feedback from readers, justifies the high costs occasioned by the dynamic testing of children's restraint systems. The popularity of this topic leads to greater sales of the particular issues of the magazine test - which carries no advertising - and at least compensates for most of the added costs necessary for dynamic collision testing. It is not generally well known that Stiftung Warentest covers approximately 90% of its budget from the sales of its two magazines test and Finanztest, and of its other special publications. The annual subsidy by the German government is relatively small. The national subsidy is intended to compensate for the loss of revenue from the exclusion of advertising. (orig.)

Physicochemical and antimicrobial properties of copaiba oil: implications on product quality control.

Science.gov (United States)

Fonseca, Renata G; Barros, Francisco M; Apel, Miriam A; Poser, Gilsane L von; Andriolli, Jo O L; Filho, Pedro C Campos; Sousa, Dhierlate F; Lobo, Ivon P; Conceiç O, Aline O

2015-01-01

The copaiba oil is a common natural product used in cosmetic industry and as a nutraceutical product. However, lack of quality control and scarce knowledge about its antimicrobial activity is a point of concern. The proposal of this study was to investigate the physicochemical properties and the antimicrobial activity of five commercial brands of copaiba oil. Acidity and ester index, refractory index, solubility in alcohol, and thin layer chromatography were performed to verify the physicochemical properties of five commercial copaiba oils sold in local pharmacies. Ultra performance liquid chromatography coupled with diode-array detection and electrospray ionization quadrupole time-of-flight mass spectrometry (UPLC-DAD/ESI-Q-TOF-MS) was used to investigate diterpene acids while the volatile compounds were analysed by gas chromatography-mass spectrometry (GC-MS). Antibacterial and antifungal activities were also evaluated by agar diffusion technique; and minimal inhibitory concentration and maximal bactericidal concentration were defined for each sample and bacteria. The physical-chemical analysis revealed heterogeneity between all samples analysed. The A1 sample showed characteristics of copaiba oil and was mainly composed by hydrocarbon sesquiterpenes (29.95% β-bisabolene, 25.65% Z-α-bergamotene and 10.27% β-cariophyllene). Among diterpene acids, the UPLCDAD/ESI-Q-TOF-MS data are compatible with presence of copalic and/or kolavenic acid (m/z 305 [M + H]+). Candida albicans was sensitive to almost all samples at high concentration and Saccaromyces. Cerevisiae showed sensitivity to A1 sample at 100 mg/mL. Although variable, all samples showed antibacterial activity. Significant activity was seen for A3 (19.0 ±0 and 15.6 ±0.5 mm), A4 (16.6 ±0.5 and 15.6 ±0 mm), and A5 (17.1 ±0 and 17.1 ±0 mm) on Staphylococcus saprophyticus and S. aureus, respectively. All samples were active against Klebsiella pneumoniae showing ≥15 mm diameter halo inhibition; and only A

Statistical study of 22 K steel machanical properties

International Nuclear Information System (INIS)

Zhevanov, O.Ya.; Kolpishon, Eh.Yu.; Egorov, M.F.

1988-01-01

Test results of 100 specimens of 22 K steel are analyzed for determination of relation between the technology of production, structure and properties of steels. Mechanical properties (ultimate strength and yield strength, relative elongation, relative narrowing, impact strength, hardness) and structural parameters are considered. Investigation into the regressive dependence between mechanical properties and the diameter of the indentor mark when determining Brinell hardness have shown that it is advisable to replace the testing mechanical properties at static extension by the control of hardness and microstructure

Calcium carbonate synthesis with prescribed properties based on liquid waste of soda production

Directory of Open Access Journals (Sweden)

E.O. Mikhailova

2016-09-01

Full Text Available A promising direction in solving of environmental problems of soda industry is the development of low-waste resource-saving technologies, which consist in recycling of valuable waste components with obtaining the commercial products. Aim: The aim is to establish the optimal conditions for obtaining calcium carbonate with prescribed properties from liquid waste of soda production. Materials and Methods: Chemically deposited calcium carbonate is used as filler and should have certain physical and chemical properties. To obtain a product of prescribed quality the process of calcium carbonate deposition was performed of still waste liquid, that is the waste of calcium carbonate production and contain significant amount of calcium ions, and excessive production of the purified stock solution of sodium bicarbonate, which is composed of carbonate and hydrocarbonate ions. Results: The dependence of bulk density and specific surface area of calcium carbonate sediments and degree of deposition from such technological parameters are established: method of mixing the stock solutions, the concentration and molar ratio of reactants, temperature and reaction time. Conclusions: The optimal mode of deposition process is determined and the concept of production of calcium carbonate is developed. The quality of calcium carbonate meets the modern requirements of high dispersion, low bulk density and evolved specific surface of the product.

The Industrial Property Rights Education in Collaboration with the Creative Product Design Education

Science.gov (United States)

Tokoro, Tetsuro; Habuchi, Hitoe; Chonan, Isao

Recently, the Advanced Courses of Electronic System Engineering and Architecture and Civil Engineering of Gifu National College of Technology have introduced a creative subject, “Creative Engineering Practice”. In this subject, students study intellectual property rights. More specifically, they learn and practice industrial proprietary rights, procedures for obtaining a patent right, how to use Industrial Property Digital Library and so forth, along with the practice of creative product design. The industrial property rights education in collaboration with the creative product design education has been carried out by the cooperation of Japan Patent Office, Japan Institute of Invention and Innovation and a patent attorney. Through the instruction of the cooperative members, great educative results have been obtained. In this paper, we will describe the contents of the subject together with its items to pursue an upward spiral of progress.

Stability and anti-glycation properties of intermediate moisture apple products fortified with green tea.

Science.gov (United States)

Lavelli, Vera; Corey, Mark; Kerr, William; Vantaggi, Claudia

2011-07-15

Intermediate moisture products made from blanched apple flesh and green tea extract (about 6mg of monomeric flavan 3-ols added per g of dry apple) or blanched apple flesh (control) were produced, and their quality attributes were investigated over storage for two months at water activity (a(w)) levels of 0.55 and 0.75, at 30°C. Products were evaluated for colour (L(∗), a(∗), and b(∗) Hunter's parameters), phytochemical contents (flavan 3-ols, chlorogenic acid, dihydrochalcones, ascorbic acid and total polyphenols), ferric reducing antioxidant potential, 2,2-diphenyl-1-(2,4,6-trinitrophenyl)hydrazyl radical-scavenging activity and ability to inhibit formation of fructose-induced advanced glycation end-products. During storage of the fortified and unfortified intermediate moisture apples, water availability was sufficient to support various chemical reactions involving phytochemicals, which degraded at different rates: ascorbic acid>flavan 3-ols>dihydrochalcones and chlorogenic acid. Colour variations occurred at slightly slower rates after green tea addition. In the intermediate moisture apple, antioxidant and anti-glycoxidative properties decreased at similar rates (half-life was about 80d at a(w) of 0.75, 30°C). In the green tea-fortified intermediate moisture apple, the antioxidant activity decreased at a slow rate (half-life was 165d at a(w) of 0.75, 30°C) and the anti-glycoxidative properties did not change, indicating that flavan 3-ol degradation involved the formation of derivatives that retained the properties of their parent compounds. Since these properties are linked to oxidative- and advanced glycation end-product-related diseases, these results suggest that green tea fortification of intermediate moisture apple products could be a valuable means of product innovation, to address consumers' nutritional needs. Copyright © 2011 Elsevier Ltd. All rights reserved.

Measurement properties of the craniocervical flexion test: a systematic review protocol.

Science.gov (United States)

Araujo, Francisco Xavier de; Ferreira, Giovanni Esteves; Scholl Schell, Maurício; Castro, Marcelo Peduzzi de; Silva, Marcelo Faria; Ribeiro, Daniel Cury

2018-02-22

Neck pain is the leading cause of years lived with disability worldwide and it accounts for high economic and societal burden. Altered activation of the neck muscles is a common musculoskeletal impairment presented by patients with neck pain. The craniocervical flexion test with pressure biofeedback unit has been widely used in clinical practice to assess function of deep neck flexor muscles. This systematic review will assess the measurement properties of the craniocervical flexion test for assessing deep cervical flexor muscles. This is a protocol for a systematic review that will follow the Preferred Reporting Items for Systematic Review and Meta-Analysis statement. MEDLINE (via PubMed), EMBASE, PEDro, Cochrane Central Register of Controlled Trials (CENTRAL), Scopus and Science Direct will be systematically searched from inception. Studies of any design that have investigated and reported at least one measurement property of the craniocervical flexion test for assessing the deep cervical flexor muscles will be included. All measurement properties will be considered as outcomes. Two reviewers will independently rate the risk of bias of individual studies using the updated COnsensus-based Standards for the selection of health Measurement Instruments risk of bias checklist. A structured narrative synthesis will be used for data analysis. Quantitative findings for each measurement property will be summarised. The overall rating for a measurement property will be classified as 'positive', 'indeterminate' or 'negative'. The overall rating will be accompanied with a level of evidence. Ethical approval and patient consent are not required since this is a systematic review based on published studies. Findings will be submitted to a peer-reviewed journal for publication. CRD42017062175. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Some Exploitation Properties of Wood Plastic Hybrid Composites Based on Polypropylene and Plywood Production Waste

Science.gov (United States)

Kajaks, Janis; Kalnins, Karlis; Uzulis, Sandris; Matvejs, Juris

2015-12-01

During the last 20-30 years many researchers have paid attention to the studies of properties of thewood polymer composites (WPC). A lot of works are closely related to investigations of exploitation properties of wood fibres or wood flour containing polyolefine composites [1, 2]. The most useful from wide selection of polyolefines are polypropylenes, but timber industry waste materials comprising lignocellulose fibres are often used as reinforcement of WPC [3-12]. Plywood industry is not an exception - part of waste materials (by-products) are used for heat energy, i.e. burned. In this work we have approbated reinforcing of polypropylene (PP) with one of the plywood industry by-products, such as birch plywood sawdust (PSWD),which containswood fibre fractions with different length [13]. The main fraction (50%) includes fibres with length l = 0.5 - 1 mm. Our previous study [13] has confirmed that PSWD is a promising filler for PP reinforcing. Addition of PSWD up to 40-50 wt.% has increased WPC tensile and flexural modulus, but decreased deformation ability of PP matrix, impact strength, water resistance and fluidity of composite melts. It was shown [13] that modification of the composites with interfacial modifier - coupling agent maleated polypropylene (MAPP content up to 5-7 wt.%) considerably improved all the abovementioned properties. SEM investigations also confirmed positive action of coupling agent on strengthening of adhesion interaction between components wood and PP matrix. Another way how to make better properties of the WPC is to form hybridcomposites [1, 14-24]. Very popular WPC modifiers are nanoparticle additions like organonanoclays, which increase WPC physical-mechanical properties - microhardness, water resistance and diminish barrier properties and combustibility [1, 2, 14-17, 19, 20]. The goal of this study was to investigate organonanoclays influence on plywood production industry by-product birch plywood sawdust (PSWD) containing

A study on the mechanical properties of additive manufactured polymer materials

Energy Technology Data Exchange (ETDEWEB)

Kim, Dong Bum; Lee, In Hwan; Cho, Hae Yong [Dept. of Mechanical Engineering, Chungbuk National University, Cheongju (Korea, Republic of)

2015-08-15

Traditionally, additive manufacturing (AM) technology has been used to fabricate prototypes in the early development phase of a product. This technology is being applied to release manufacturing of a product because of its low cost and fast fabrication. AM technology is a process of joining materials to fabricate a product from the 3D CAD data in a layer-by-layer manner. The orientation of a layer during manufacturing can affect the mechanical properties of the product because of its anisotropy. In this paper, tensile testing of polymer-based specimens were built with a typical AM process (FDM, PolyJet and SLA) to study the mechanical properties of the AM materials. The ASTM D 638 tensile testing standard was followed for building the specimens. The mechanical properties of the specimens were determined on the basis of stress-strain curves formed by tensile tests. In addition, the fracture surfaces of the specimens were observed by SEM to analyze the results.

Mechanical property test of natural rubber bearing for the evaluation of uncertainty value of seismic isolation devices

International Nuclear Information System (INIS)

Kim, Min Kyu; Kim, Jung Han; Choi, In Kil

2012-01-01

Seismic safety of NPP is one of the most important issues in a nuclear field after great east Japan earthquake in 2011. For the improvement of seismic safety of nuclear power plant, seismic isolation is the easiest solution for increasing the seismic safety. Otherwise, the application of seismic isolation devices for nuclear power plants doesn't make the seismic risk of NPP increases always. The rubber bearing have many uncertainties of material properties and large displacement should absorb according to the application of isolation devices. In this study, for the evaluation of uncertainty of the material properties of rubber bearing, material tests for rubber and mechanical properties test for natural rubber bearing were performed. For the evaluation of effect of hardness of rubber, 4 kinds of rubber hardness for material property tests and 2 kinds of rubber hardness for mechanical property test were considered. As a result, the variation of material properties is higher than that of mechanical properties of natural rubber bearings

Chemical test for mammalian feces in grain products: collaborative study.

Science.gov (United States)

Gerber, H R

1989-01-01

A collaborative study was conducted to validate the use of the AOAC alkaline phosphatase method for mammalian feces in corn meal, 44.B01-44.B06, for 7 additional products: brown rice cream, oat bran, grits, semolina, pasta flour, farina, and barley plus (a mixture of barley, oat bran, and brown rice). The proposed method determines the presence of alkaline phosphatase, an enzyme contained in mammalian feces, by using phenolphthalein diphosphate as the enzyme substrate in a test agar medium. Fecal matter is separated from the grain products by specific gravity differences in 1% test agar. As the product is distributed on liquid test agar, fecal fragments float while the grain products sink. The alkaline phosphatase cleaves phosphate radicals from phenolphthalein diphosphate, generating free phenolphthalein, which produces a pink to red-purple color around the fecal particles in the previously colorless medium. Collaborators' recovery averages ranged from 21.7 particles (72.3%) for oat bran to 25.3 particles (84.3%) for semolina at the 30 particle spike level. Overall average background was 0.4 positive reactions per food type. The collaborators reported that the method was quick, simple, and easy to use. The method has been approved interim official first action for all 7 grain products.

Production and test of the LHCf microstrip silicon system

International Nuclear Information System (INIS)

Bonechi, L.; Adriani, O.; Bongi, M.; Castellini, G.; D'Alessandro, R.; Faus, A.; Haguenauer, M.; Itow, Y.; Kasahara, K.; Macina, D.; Mase, T.; Masuda, K.; Matsubara, Y.; Matsumoto, H.; Menjo, H.; Mizuishi, M.; Muraki, Y.; Papini, P.; Perrot, A.L.; Ricciarini, S.

2008-01-01

After a preliminary installation test, successfully performed in 2007, both the detectors of the LHCf experiment are now ready to be installed at the CERN LHC accelerator for the first physics run. A beam test at SPS in September 2007 allowed to verify the performance of the apparata. Production and test of the silicon tracker developed for one of them are shortly discussed in this work.

Measurement properties of maximal cardiopulmonary exercise tests protocols in persons after stroke: A systematic review.

Science.gov (United States)

Wittink, Harriet; Verschuren, Olaf; Terwee, Caroline; de Groot, Janke; Kwakkel, Gert; van de Port, Ingrid

2017-11-21

To systematically review and critically appraise the literature on measurement properties of cardiopulmonary exercise test protocols for measuring aerobic capacity, VO2max, in persons after stroke. PubMed, Embase and Cinahl were searched from inception up to 15 June 2016. A total of 9 studies were identified reporting on 9 different cardiopulmonary exercise test protocols. VO2max measured with cardiopulmonary exercise test and open spirometry was the construct of interest. The target population was adult persons after stroke. We included all studies that evaluated reliability, measurement error, criterion validity, content validity, hypothesis testing and/or responsiveness of cardiopulmonary exercise test protocols. Two researchers independently screened the literature, assessed methodological quality using the COnsensus-based Standards for the selection of health Measurement INstruments checklist and extracted data on measurement properties of cardiopulmonary exercise test protocols. Most studies reported on only one measurement property. Best-evidence synthesis was derived taking into account the methodological quality of the studies, the results and the consistency of the results. No judgement could be made on which protocol is "best" for measuring VO2max in persons after stroke due to lack of high-quality studies on the measurement properties of the cardiopulmonary exercise test.

Environmental impact of petroleum products in the soil. Part II: Petroleum products composition and key properties

International Nuclear Information System (INIS)

Zerlia, T.

2001-01-01

The fate of petroleum hydrocarbons in the soil depends on the chemical-physic properties of each hydrocarbon, as well as on the soil characteristics. The mean composition of various petroleum products, the key chemical compounds and their characteristics are focused in order to outline the environmental behaviour of petroleum hydrocarbons in the soil [it

The influence of socio-cultural background and product value in usability testing.

Science.gov (United States)

Sonderegger, Andreas; Sauer, Juergen

2013-05-01

This article examines the influence of socio-cultural background and product value on different outcomes of usability tests. A study was conducted in two different socio-cultural regions, Switzerland and East Germany, which differed in a number of aspects (e.g. economic power, price sensitivity and culture). Product value (high vs. low) was varied by manipulating the price of the product. Sixty-four test participants were asked to carry out five typical user tasks in the context of coffee machine usage, measuring performance, perceived usability, and emotion. The results showed that in Switzerland, high-value products were rated higher in usability than low-value products whereas in East Germany, high-value products were evaluated lower in usability. A similar interaction effect of socio-cultural background and product value was observed for user emotion. Implications are that the outcomes of usability tests do not allow for a simple transfer across cultures and that the mediating influence of perceived product value needs to be taken into consideration. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Development, Production and Testing of 4500 Beam Loss Monitors

CERN Document Server

Holzer, E B; Dehning, B; Ferioli, G; Grishin, V; Jimenez, T M; Koshelev, A; Kramer, Daniel; Larionov, A; Taborelli, M; Seleznev, V; Sleptsov, M; Sytin, A; Wevers, I

2008-01-01

Beam-loss monitoring (BLM) [1] is a key element in the LHC machine protection. 4250 nitrogen filled ionization chambers (IC) and 350 secondary emission monitors (SEM) have been manufactured and tested at the Institute for High Energy Physics (IHEP) in Protvino, Russia, following their development at CERN. Signal speed and robustness against aging were the main design criteria. Each monitor is permanently sealed inside a stainless-steel cylinder. The quality of the welding was a critical aspect during production. The SEMs are requested to hold a vacuum of $10^{-7}$ bar. Impurity levels from thermal and radiationinduced desorption should remain in the range of parts per million in the ICs. To avoid radiation aging (up to $2·10^{8}$ Gy in 20 years) production of the chambers followed strict UHV requirements. IHEP designed and built the UHV production stand. Due to the required dynamic range of $10^{8}$, the leakage current of the monitors has to stay below 2 pA. Several tests during and after production were ...

Production circulator fabrication and testing for core flow test loop. Final report, Phase III

Energy Technology Data Exchange (ETDEWEB)

1981-05-01

The performance testing of two production helium circulators utilizing gas film lubrication is described. These two centrifugal-type circulators plus an identical circulator prototype will be arranged in series to provide the helium flow requirements for the Core Flow Test Loop which is part of the Gas-Cooled Fast Breeder Reactor Program (GCFR) at the Oak Ridge National Laboratory. This report presents the results of the Phase III performance and supplemental tests, which were carried out by MTI during the period of December 18, 1980 through March 19, 1981. Specific test procedures are outlined and described, as are individual tests for measuring the performance of the circulators. Test data and run descriptions are presented.

Production circulator fabrication and testing for core flow test loop. Final report, Phase III

International Nuclear Information System (INIS)

1981-05-01

The performance testing of two production helium circulators utilizing gas film lubrication is described. These two centrifugal-type circulators plus an identical circulator prototype will be arranged in series to provide the helium flow requirements for the Core Flow Test Loop which is part of the Gas-Cooled Fast Breeder Reactor Program (GCFR) at the Oak Ridge National Laboratory. This report presents the results of the Phase III performance and supplemental tests, which were carried out by MTI during the period of December 18, 1980 through March 19, 1981. Specific test procedures are outlined and described, as are individual tests for measuring the performance of the circulators. Test data and run descriptions are presented

OPERATING STABILITY OF MINERAL WOOL PRODUCTS

Directory of Open Access Journals (Sweden)

Perfilov Vladimir Aleksandrovich

2016-03-01

Full Text Available Creating an effective insulation envelope of the building is possible only using high-quality materials, preserving their characteristics both in the early stages of operation, and for the whole billing period. It is an important opportunity to assess the thermal insulation properties and predict its changes over time directly in the conditions of the construction site. The products based on mineral fibers (rock and glass wool, basalt fiber are the most widely used type of insulating materials in the domestic construction. Therefore, the operational stability valuation methods must be primarily created for this group of products. The methodology for assessing the thermal insulation properties includes two main components: testing equipment and methodology for assessing the operational stability. The authors tested the methodology of the accelerated testing and prediction of durability for mineral wool products of laminated, corrugated and volume-oriented structures. The test results give good convergence with the methods recommended by the building regulations. Application of thermal insulation materials are an effective way to form the thermal envelope of the building, reducing energy costs and increasing the durability of building structures. The material properties are determined by their structure, which is formed during the technological impacts.

Problems of metrological supply of carbon materials production

International Nuclear Information System (INIS)

Belov, G.V.; Bazilevskij, L.P.; Cherkashina, N.V.

1989-01-01

Carbon materials and products contain internal residual stresses and have an anisotropy of properties therefore special methods of tests are required to control their quality. The main metrological problems during development, production and application of carbon products are: metrological supply of production forms and records during the development of production conditions; metrological supply of quality control of the product; metrological supply of methods for the tests of products and the methods to forecast the characteristics of product quality for the period of quaranteed service life

A/T test system for production line; Seisan line yo A/T test system

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-10

This paper introduces an A/T test system for production line made by Meidensha, Inc. Rates and technology of mounting auto-transmissions (A/T) in recent automobiles are improving year after year. A/T production line testers were fabricated and supplied, including those for European countries. This system has the following features: the system employs low inertia AC motor, and is capable of performing tests in close conditions to actual cars; an insulated gate bipolar transistor (IGBT) inverter was employed to achieve control accuracy improvement and noise reduction; high-velocity transient measurement is possible by using a computer system based on the WindowsNT; a solenoid current slant control was employed to respond to electronically controlled A/T; and noise and vibration shift feeling instrumentation can also be used on option. Number of supply is four sets of front engine/front wheel drive (FF) car A/T testers for overseas countries, and two sets of FF A/T tests for use in Japan. (NEDO)

Mechanical Properties of Commercial Carbon Fibers Using a Single Filament Tensile Test

International Nuclear Information System (INIS)

Joh, Han-Ik; Song, Hae Kyung; Ku, Bon-Cheol; Lee, Sungho; Kim, Ki-Young; Kang, Phil-Hyun

2013-01-01

In this study, mechanical properties of commercial carbon fibers were evaluated using a single filament tensile test with various fiber gauge lengths. Tensile strength increased significantly with a decreasing length of the test specimens possibly due to small defect sites. The compliance method provided more accurate moduli of the carbon fibers, removing system errors during the single filament tensile test. The Weibull modulus revealed that shorter specimens had an inhomogeneous defect distribution, leading to a higher tensile strength and its standard deviation. X-ray diffractograms of carbon fibers showed a similar crystallinity and orientation in spite of significant differences in the fiber modulus and strength, indicating that crystalline structure of the commercial carbon fibers used in the study was not attributable to the difference in their tensile properties.

Bio energy: Bio fuel - Properties and Production

International Nuclear Information System (INIS)

Wilhelmsen, Gunnar; Martinsen, Arnold Kyrre; Sandberg, Eiliv; Fladset, Per Olav; Kjerschow, Einar; Teslo, Einar

2001-01-01

This is Chapter 3 of the book ''Bio energy - Environment, technique and market''. Its main sections are: (1) Definitions and properties, (2) Bio fuel from the forest, (3) Processed bio fuel - briquettes, pellets and powder, (4) Bio fuel from agriculture, (5) Bio fuel from agro industry, (6) Bio fuel from lakes and sea, (7) Bio fuel from aquaculture, (8) Bio fuel from wastes and (9) Hydrogen as a fuel. The exposition largely describes the conditions in Norway. The chapter on energy from the forest includes products from the timber and sawmill industry, the pulp and paper industry, furniture factories etc. Among agricultural sources are straw, energy forests, vegetable oil, bio ethanol, manure

New product testing and the utilization of user expertise: Evidence from the Pharmaceutical industry

DEFF Research Database (Denmark)

Smed, Marie; Salomo, Søren; Schultz, Carsten

2012-01-01

A significant and often neglected obstacle in new product development is the testing and approval process in the late stages of development. The testing process has primarily been observed as an in-house decision process, however, in many industries products undergo extensive testing before marke....... Further, with a dispersed user network a positive effect is observed on the mean to communicate directly as issues occur. The effect of virtual communication is therefore stronger than traditional face-to-face interaction patterns.......A significant and often neglected obstacle in new product development is the testing and approval process in the late stages of development. The testing process has primarily been observed as an in-house decision process, however, in many industries products undergo extensive testing before market...... the knowledge generated and shared by medical sites and Pharmaceutical producers in late stage product development. The results show, that information regarding usage patterns and product related services are more difficult to transfer between user and developer, than issues directly related to the product...

Development of post-irradiation test facility for domestic production of 99Mo

International Nuclear Information System (INIS)

Taguchi, Taketoshi; Yonekawa, Minoru; Kato, Yoshiaki; Kurosawa, Makoto; Nishikata, Kaori; Ishida, Takuya; Kawamata, Kazuo

2013-01-01

JMTR focus on the activation method. By carrying out the preliminary tests using irradiation facilities existing, and verification tests using the irradiation facility that has developed in the cutting-edge research and development strategic strengthening business, as irradiation tests towards the production of 99 Mo, we have been conducting research and development that can contribute to supply about 25% for 99 Mo demand in Japan and the stable supply of radiopharmaceutical. This report describes a summary of the status of the preliminary tests for the production of 99 Mo: Maintenance of test equipment in the facility in JMTR hot laboratory in preparation for research and development for the production of 99 Mo in JMTR and using MoO 3 pellet irradiated at Kyoto University Research Reactor Institute (KUR). (author)

Off-Line Testing of Tribo-Systems for Sheet Metal Forming Production

DEFF Research Database (Denmark)

Bay, Niels; Ceron, Ermanno

2014-01-01

Off-line testing of new tribo-systems for sheet metal forming production is an important issue, when new, environmentally benign lubricants are to be introduced. To obtain useful results it is, however, vital to ensure similar conditions as in the production process regarding the main tribo...... leading to very high tool/workpiece interface pressure and temperature in the second re-draw. Under such conditions only the best lubricant systems work satisfactory, and the paper shows how the performance of different tribo-systems in production may be predicted by off-line testing combined...

Properties of various plants and animals feedstocks for biodiesel production.

Science.gov (United States)

Karmakar, Aninidita; Karmakar, Subrata; Mukherjee, Souti

2010-10-01

As an alternative fuel biodiesel is becoming increasingly important due to diminishing petroleum reserves and adverse environmental consequences of exhaust gases from petroleum-fuelled engines. Biodiesel, the non-toxic fuel, is mono alkyl esters of long chain fatty acids derived from renewable feedstock like vegetable oils, animal fats and residual oils. Choice of feedstocks depends on process chemistry, physical and chemical characteristics of virgin or used oils and economy of the process. Extensive research information is available on transesterification, the production technology and process optimization for various biomaterials. Consistent supply of feedstocks is being faced as a major challenge by the biodiesel production industry. This paper reviews physico-chemical properties of the plant and animal resources that are being used as feedstocks for biodiesel production. Efforts have also been made to review the potential resources that can be transformed into biodiesel successfully for meeting the ever increasing demand of biodiesel production. Copyright 2010 Elsevier Ltd. All rights reserved.

Use of test results from the percolation leaching test (TS3) in the framework of the Construction Products Directive

Energy Technology Data Exchange (ETDEWEB)

Van Zomeren, A.; Dijkstra, J.J. [ECN Environment and Energy Engineering, Petten (Netherlands); Mesman, M.; Spijker, J. [National Institute for Public Health and the Environment RIVM, Bilthoven (Netherlands); Eikelboom, R. [Ministry of Infrastructure and Environment IenM, Den Haag (Netherlands)

2013-10-15

The enforcement of the European Construction Products Directive (and the more actual Construction Products Regulation) has led to the development of European harmonised standards for assessment of the emission of 'dangerous substances' from construction materials. According to Basic Working Requirement (BWR) number 3, the emissions from construction products to soil and groundwater should not have an unacceptable impact on the environmental quality over the life cycle of the product. In this paper the technical needs and boundary conditions of leaching tests to obtain meaningful and reliable test results are explained. Although this paper will not go into detail on 'impact assessment' and the resulting development of regulatory criteria, we will show that the technical needs and boundary conditions of a test are to some extent dependent on what type of information is needed by regulators for environmental impact assessment. This short paper focuses on explaining the principles of testing leaching behaviour of aggregates, and briefly explains the leaching of size reduced and non-size reduced particles. It provides information for the actual discussions on size reduction before leaching tests.

Quantitative accelerated degradation testing: Practical approaches

International Nuclear Information System (INIS)

Mohammadian, S. Hossein; Ait-Kadi, Daoud; Routhier, Francois

2010-01-01

The concept of accelerated testing by tracking degradation of samples over test time needs to be developed for reliability estimation. This paper aims at proposing practical approaches to conduct accelerated degradation testing on new and available used samples. For this purpose, product failure is related to a suitable physical property. Then, its failure time is defined as the expected time in which its property reaches the critical level. Degradation model of field samples returned from service due to a degrading failure mode has been estimated based on the least square method, and available gap between manufacturer criterion and user's claim (to report a failure) has also been discussed. For a product under some stresses, a general formula has been proposed by the superposition principle in order to estimate its degradation for independent and dependent failure modes. If used samples are available, and acceleration factor of the related test is unknown, partial aging method has been presented to considerably shorten the test time.

Orally inhaled drug performance testing for product development, registration, and quality control.

Science.gov (United States)

Lastow, Orest; Svensson, Mårten

2014-12-01

A DPI can be split into three different modules; device, formulation, process. These are developed in parallel, and together with the user they provide the performance of an inhalation product. During product development, these modules are evolving and changing, whereas the requirements on an inhalation product are always expressed in terms of the performance of the final commercial product. To do performance testing during development when the product is not finished presents many challenges and can be confusing and misleading. During development, the performance of the final product is typically being predicted by testing ever changing prototypes. This article describes methods and approaches to manage such development and to, during development, provide relevant predictions of the in vitro and in vivo performances of the final product.

Production and properties of an exopolysaccharide synthesized by the extreme halophilic archaeon Haloterrigena turkmenica.

Science.gov (United States)

Squillaci, Giuseppe; Finamore, Rosario; Diana, Paola; Restaino, Odile Francesca; Schiraldi, Chiara; Arbucci, Salvatore; Ionata, Elena; La Cara, Francesco; Morana, Alessandra

2016-01-01

We have isolated a novel exopolysaccharide (EPS) produced by the extreme halophilic archaeon Haloterrigena turkmenica. Some features, remarkable from an industrial point of view, such as emulsifying and antioxidant properties, were investigated. H. turkmenica excreted 20.68 mg of EPS per 100 ml of culture medium when grown in usual medium supplemented with glucose. The microorganism excreted the biopolymer mainly in the middle exponential growth phase and reached the maximal production in the stationary phase. Analyses by anion exchange chromatography and SEC-TDA Viscotek indicated that the EPS was composed of two main fractions of 801.7 and 206.0 kDa. It was a sulfated heteropolysaccharide containing glucose, galactose, glucosamine, galactosamine, and glucuronic acid. Studies performed utilizing the mixture of EPS anionic fractions showed that the biopolymer had emulsifying activity towards vegetable oils comparable or superior to that exhibited by the controls, moderate antioxidant power when tested with 2,2'-diphenyl-1-picrylhydrazyl (DPPH(·)), and moisture-retention ability higher than hyaluronic acid (HA). The EPS from H. turkmenica is the first exopolysaccharide produced by an archaea to be characterized in terms of properties that can have potential biotechnological applications.

Psychometric characteristics of single-word tests of children's speech sound production.

Science.gov (United States)

Flipsen, Peter; Ogiela, Diane A

2015-04-01

Our understanding of test construction has improved since the now-classic review by McCauley and Swisher (1984). The current review article examines the psychometric characteristics of current single-word tests of speech sound production in an attempt to determine whether our tests have improved since then. It also provides a resource that clinicians may use to help them make test selection decisions for their particular client populations. Ten tests published since 1990 were reviewed to determine whether they met the 10 criteria set out by McCauley and Swisher (1984), as well as 7 additional criteria. All of the tests reviewed met at least 3 of McCauley and Swisher's (1984) original criteria, and 9 of 10 tests met at least 5 of them. Most of the tests met some of the additional criteria as well. The state of the art for single-word tests of speech sound production in children appears to have improved in the last 30 years. There remains, however, room for improvement.

MicroCHP: Overview of selected technologies, products and field test results

Energy Technology Data Exchange (ETDEWEB)

Kuhn, Vollrad [Berliner Energieagentur GmbH, Franzoesische Strasse 23, 10117 Berlin (Germany); Klemes, Jiri; Bulatov, Igor [Centre for Process Integration, CEAS, The University of Manchester, P.O. Box 88, M60 1QD Manchester (United Kingdom)

2008-11-15

This paper gives an overview on selected microCHP technologies and products with the focus on Stirling and steam machines. Field tests in Germany, the UK and some other EC countries are presented, assessed and evaluated. Test results show the overall positive performance with differences in sectors (domestic vs. small business). Some negative experiences have been received, especially from tests with the Stirling engines and the free-piston steam machine. There are still obstacles for market implementation. Further projects and tests of microCHP are starting in various countries. When positive results will prevail and deficiencies are eliminated, a way to large-scale production and market implementation could be opened. (author)

Product evaluation of in situ vitrification engineering, Test 4

International Nuclear Information System (INIS)

Loehr, C.A.; Weidner, J.R.; Bates, S.O.

1991-09-01

This report is one of several that evaluates the In Situ Vitrification (ISV) Engineering-Scale Test 4 (ES-4). This document describes the chemical and physical composition, microstructure, and leaching characteristics of ES-4 product samples; these data provide insight into the expected performance of a vitrified product in an ISV buried waste application similar to that studied in ES-4

Slim hole drilling and testing strategies

Science.gov (United States)

Nielson, Dennis L.; Garg, Sabodh K.; Goranson, Colin

2017-12-01

The financial and geologic advantages of drilling slim holes instead of large production wells in the early stages of geothermal reservoir assessment has been understood for many years. However, the practice has not been fully embraced by geothermal developers. We believe that the reason for this is that there is a poor understanding of testing and reservoir analysis that can be conducted in slim holes. In addition to reservoir engineering information, coring through the cap rock and into the reservoir provides important data for designing subsequent production well drilling and completion. Core drilling requires significantly less mud volume than conventional rotary drilling, and it is typically not necessary to cure lost circulation zones (LCZ). LCZs should be tested by either production or injection methods as they are encountered. The testing methodologies are similar to those conducted on large-diameter wells; although produced and/or injected fluid volumes are much less. Pressure, temperature and spinner (PTS) surveys in slim holes under static conditions can used to characterize temperature and pressure distribution in the geothermal reservoir. In many cases it is possible to discharge slim holes and obtain fluid samples to delineate the geochemical properties of the reservoir fluid. Also in the latter case, drawdown and buildup data obtained using a downhole pressure tool can be employed to determine formation transmissivity and well properties. Even if it proves difficult to discharge a slim hole, an injection test can be performed to obtain formation transmissivity. Given the discharge (or injection) data from a slimhole, discharge properties of a large-diameter well can be inferred using wellbore modeling. Finally, slim hole data (pressure, temperature, transmissivity, fluid properties) together with reservoir simulation can help predict the ability of the geothermal reservoir to sustain power production.

FUNGISTATIC PROPERTIES OF GRANULATED BLASTFURNACE SLAG AND RELATED SLAG-CONTAINING CEMENTS

Directory of Open Access Journals (Sweden)

Julius Strigac

2016-03-01

Full Text Available The article deals with studying the antifungal effect of ground granulated blastfurnace slag (GGBS and the cements made from it. Antifungal effects were tested on the fungi using the procedure given in the Czech national standard CSN 72 4310: 1977 - Testing the mould proofness properties of building products and materials. A mixture of the fungi Aspergillus niger, Chaetomium globosum, Penicillium funiculosum, Paecilomyces variotii and Gliocladium virens was used for testing. The scale for evaluating mould proofness properties according to CSN 72 4310: 1977 is from 0 to 5 in degree of fungi growth, where a value of 0 means that no growth of fungi occurs and the building products and materials possess fungistatic properties. The study confirms the fungistatic propeties of GGBS with mould proofness property 0. The addition of GGBS to cements from 65 wt.% to 95 wt.% ensures the achieving of a fungistatic environment, which enables the production of fungistatic blastfurnace cements CEM III/A 32.5 N (with GGBS content of 65 wt.%, CEM III/B 32.5 N and CEM III/C 32.5 N with mould proofness property 0.

The trade of virtual water: do property rights matter?

Science.gov (United States)

Xu, Ankai

2016-04-01

My paper examines the determinants of the virtual water trade - embodied in the trade of agriculture products - by estimating a structural gravity model. In particular, it tests the relationship between property rights and the export of water-intensive agricultural products based on water footprint data in Mekonnen and Hoekstra (2011, 2012). Using two different measures of property rights protection, I show that countries with weaker property rights have an apparent comparative advantage in the trade of water-intensive products. After controlling for the economic size, natural resource endowments, and possible effects of reverse causality, the trade flow of virtual water is negatively and significantly correlated with the property rights index of the exporting country. Holding other factors constant, one point increase in the property rights index of a country is associated with a 24% - 36% decrease in its virtual water export, whereas a 1% increase in the natural resource protection index of a country is associated with a 16% decrease in its virtual water export. This paper is the first empirical work that tests the relationship between property rights and trade of water-intensive products, offering a new perceptive in the debate of virtual water trade. The findings provide a possible explanation on the paradoxical evidence that some countries with scarce water resources export water-intensive products. The result is important not only in terms of its theoretical relevance, but also its policy implications. As prescribed by the model of trade and property rights, when countries with weaker property rights open to international trade, they are more likely to over-exploit and thus expedite the depletion of natural resources.

Testing controlled productive knowledge of adverb-verb collocations ...

African Journals Online (AJOL)

A controlled productive test of adverb-verb collocations ..... The third approach to studying collocations, corpus analysis, ..... The collocation web model is thought to match Nation's (2001) psychological .... Theory, analysis, and applications. .... Canadian Modern ... Focus on vocabulary: Mastering the Academic Word List.

40 CFR 1048.301 - When must I test my production-line engines?

Science.gov (United States)

2010-07-01

... engines? 1048.301 Section 1048.301 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, LARGE NONROAD SPARK-IGNITION ENGINES Testing Production-line Engines § 1048.301 When must I test my production-line engines? (a) If you produce engines...

40 CFR 1045.301 - When must I test my production-line engines?

Science.gov (United States)

2010-07-01

... engines? 1045.301 Section 1045.301 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND VESSELS Testing Production-line Engines § 1045.301 When must I test my production-line engines? (a) If you produce...

Soil Properties and Plant Biomass Production in Natural Rangeland Management Systems

Directory of Open Access Journals (Sweden)

Romeu de Souza Werner

Full Text Available ABSTRACT Improper management of rangelands can cause land degradation and reduce the economic efficiency of livestock activity. The aim of this study was to evaluate soil properties and quantify plant biomass production in four natural rangeland management systems in the Santa Catarina Plateau (Planalto Catarinense of Brazil. The treatments, which included mowed natural rangeland (NR, burned natural rangeland (BR, natural rangeland improved through the introduction of plant species after harrowing (IH, and natural rangeland improved through the introduction of plant species after chisel plowing (IC, were evaluated in a Nitossolo Bruno (Nitisol. In the improved treatments, soil acidity was corrected, phosphate fertilizer was applied, and intercropped annual ryegrass (Lolium multiflorum, velvet grass (Holcus lanatus, and white clover (Trifolium repens were sown. Management systems with harrowed or chisel plowed soil showed improved soil physical properties; however, the effect decreased over time and values approached those of burned and mowed natural rangelands. Natural rangeland systems in the establishment phase had little influence on soil organic C. The mowed natural rangeland and improved natural rangeland exhibited greater production of grazing material, while burning the field decreased production and increased the proportion of weeds. Improvement of the natural rangelands increased leguminous biomass for pasture.

Optimization of BI test parameters to investigate mechanical properties of Grade 92 steel

Science.gov (United States)

Barbadikar, Dipika R.; Vincent, S.; Ballal, Atul R.; Peshwe, Dilip R.; Mathew, M. D.

2018-04-01

The ball indentation (BI) testing is used to evaluate the tensile properties of materials namely yield strength, strength coefficient, ultimate tensile strength, and strain hardening exponent. The properties evaluated depend on a number of BI test parameters. These parameters include the material constants like yield slope (YS), constraint factor (CF), yield offset parameter (YOP). Number of loading/unloading cycles, preload, indenter size and depth of penetration of indenter also affects the properties. In present investigation the effect of these parameters on the stress-strain curve of normalized and tempered Grade 92 steel is evaluated. Grade 92 is a candidate material for power plant application over austenitic stainless steel and derives its strength from M23C6, MX precipitates and high dislocation density. CF, YS and YOP changed the strength properties considerably. Indenter size effect resulted in higher strength for smaller indenter. It is suggested to use larger indenter diameter and higher number of loading cycles for GRADE 92 steel to get best results using BI technique.

46 CFR 163.002-27 - Production tests and examination.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Production tests and examination. 163.002-27 Section 163... examination. Each pilot hoist manufactured under Coast Guard approval must be tested as prescribed in § 163... laboratory must also conduct the visual examination described in § 163.002-21(b). The hoist may not be sold...

Hydrate-Bearing Clayey Sediments: Morphology, Physical Properties, Production and Engineering/Geological Implications

Energy Technology Data Exchange (ETDEWEB)

Dai, Sheng [Georgia Tech Research Corporation, Atlanta, GA (United States); Santamarina, J. Carlos [King Abdulaziz Univ., Jeddah (Saudi Arabia)

2017-12-30

Fine-grained sediments host more than 90 percent of global gas hydrate accumulation. However, hydrate formation in clay-dominated sediments is less understood and characterized than other types of hydrate occurrence. There is an inadequate understanding of hydrate formation mechanisms, segregation structures, hydrate lens topology, system connectivity, and physical macro-scale properties of clay-dominated hydrate-bearing sediments. This situation hinders further analyses of the global carbon budget as well as engineering challenges/solutions related to hydrate instability and production. This project studies hydrate-bearing clay-dominated sediments with emphasis on the enhanced fundamental understanding of hydrate formation and resulting morphology, the development laboratory techniques to emulate natural hydrate formations, the assessment of analytical tools to predict physical properties, the evaluation of engineering and geological implications, and the advanced understanding of gas production potential from finegrained sediments.

Properties of neutron-rich nuclei studied by fission product nuclear chemistry

International Nuclear Information System (INIS)

Meyer, R.A.; Henry, E.A.; Griffin, H.C.; Lien, O.G. III; Lane, S.M.; Stevenson, P.C.; Yaffe, R.P.; Skarnemark, G.

1979-09-01

A review is given of the properties of neutron-rich nuclei studied by fission product nuclear chemistry and includes the techniques used in elemental isolation and current research on the structure of nuclei near 132 Sn, particle emission, and coexisting structure in both neutron-poor and neutron-rich nuclei. 35 references

Photocatalysis applied to concrete products - Part 1: Principles and test procedure

NARCIS (Netherlands)

Hunger, M.; Hüsken, G.; Brouwers, H.J.H.

2008-01-01

This three-part article addresses the photocatalytic properties of concrete containing titanium dioxide (TiO2). In the first part, the evaluation of the air purifying abilities of the final concrete product is described. A setup for measuring the performance of photocatalytic active concrete

Antimicrobial properties and the influence of temperature on secondary metabolite production in cold environment soil fungi

Science.gov (United States)

Yogabaanu, U.; Weber, Jean-Frederic Faizal; Convey, Peter; Rizman-Idid, Mohammed; Alias, Siti Aisyah

2017-12-01

The Arctic and Antarctic share environmental extremes. To survive in such environments, microbes such as soil fungi need to compete with or protect themselves effectively from other soil microbiota and to obtain the often scarce nutrients available, and many use secondary metabolites to facilitate this. We therefore (i) screened for antimicrobial properties of cold-environment Arctic and Antarctic soil fungi, and (ii) identified changes in the secreted secondary metabolite profiles of a subset of these strains in response to temperature variation. A total of 40 polar soil fungal strains from King George Island, maritime Antarctic and Hornsund, Svalbard, High Arctic, were obtained from the Malaysian National Antarctic Research Centre culture collections. The plug assay technique was used to screen for antimicrobial potential against Gram-positive and Gram-negative human pathogenic bacteria (Bacillus subtilis, B. cereus, Pseudomonas aeruginosa, Enterococcus faecalis and Escherichia coli). About 45% of the tested fungal strains showed antimicrobial activity against at least one tested microorganism. Three fungal isolates showed good bioactivity and were subjected to secondary metabolite profiling at different temperatures (4, 10, 15 and 28 °C). We observed a range of responses in fungal metabolite production when incubated at varying temperatures, confirming an influence of environmental conditions such as temperature on the production of secondary metabolites.

Psychometric Properties of the Persian Adaptation of Mini-Cog Test in Iranian Older Adults.

Science.gov (United States)

Rezaei, Mohammad; Rashedi, Vahid; Lotfi, Gohar; Shirinbayan, Peymaneh; Foroughan, Mahshid

2018-04-01

The aim of this study was to assess the psychometric properties of the Mini-Cog in Iranian older adults. It was a cross-sectional study; 50 older people with dementia and 50 without dementia who matched for age, gender, and education entered the study. The diagnostic and statistical manual of mental disorders criteria for dementia were used as gold standard. A battery of scales included the abbreviated mental test score (AMTS), the Geriatric Depression Scale, and the Mini-Cog was performed. Validity and reliability of the Mini-Cog determined using the Pearson product-moment correlation coefficient (Pearson's r), Cronbach's alpha, and Receiver Operating Characteristic (ROC) curve analysis. The Persian version of Mini-Cog showed a good inter-rater reliability ( K = 0.76, p Mini-Cog have an acceptable sensitivity, specificity, and substantial overall agreement with the AMTS.

Impact of the interaction of material production and mechanical processing on the magnetic properties of non-oriented electrical steel

Science.gov (United States)

Leuning, Nora; Steentjes, Simon; Stöcker, Anett; Kawalla, Rudolf; Wei, Xuefei; Dierdorf, Jens; Hirt, Gerhard; Roggenbuck, Stefan; Korte-Kerzel, Sandra; Weiss, Hannes A.; Volk, Wolfram; Hameyer, Kay

2018-04-01

Thin laminations of non-grain oriented (NO) electrical steels form the magnetic core of rotating electrical machines. The magnetic properties of these laminations are therefore key elements for the efficiency of electric drives and need to be fully utilized. Ideally, high magnetization and low losses are realized over the entire polarization and frequency spectrum at reasonable production and processing costs. However, such an ideal material does not exist and thus, achievable magnetic properties need to be deduced from the respective application requirements. Parameters of the electrical steel such as lamination thickness, microstructure and texture affect the magnetic properties as well as their polarization and frequency dependence. These structural features represent possibilities to actively alter the magnetic properties, e.g., magnetization curve, magnetic loss or frequency dependence. This paper studies the influence of production and processing on the resulting magnetic properties of a 2.4 wt% Si electrical steel. Aim is to close the gap between production influence on the material properties and its resulting effect on the magnetization curves and losses at different frequencies with a strong focus on occurring interdependencies between production and mechanical processing. The material production is realized on an experimental processing route that comprises the steps of hot rolling, cold rolling, annealing and punching.

Impact of the interaction of material production and mechanical processing on the magnetic properties of non-oriented electrical steel

Directory of Open Access Journals (Sweden)

Nora Leuning

2018-04-01

Full Text Available Thin laminations of non-grain oriented (NO electrical steels form the magnetic core of rotating electrical machines. The magnetic properties of these laminations are therefore key elements for the efficiency of electric drives and need to be fully utilized. Ideally, high magnetization and low losses are realized over the entire polarization and frequency spectrum at reasonable production and processing costs. However, such an ideal material does not exist and thus, achievable magnetic properties need to be deduced from the respective application requirements. Parameters of the electrical steel such as lamination thickness, microstructure and texture affect the magnetic properties as well as their polarization and frequency dependence. These structural features represent possibilities to actively alter the magnetic properties, e.g., magnetization curve, magnetic loss or frequency dependence. This paper studies the influence of production and processing on the resulting magnetic properties of a 2.4 wt% Si electrical steel. Aim is to close the gap between production influence on the material properties and its resulting effect on the magnetization curves and losses at different frequencies with a strong focus on occurring interdependencies between production and mechanical processing. The material production is realized on an experimental processing route that comprises the steps of hot rolling, cold rolling, annealing and punching.

Test marketing of new smokeless tobacco products in four U.S. cities.

Science.gov (United States)

Rogers, John D; Biener, Lois; Clark, Pamela I

2010-01-01

This exploratory study was designed to assess the availability, price, and point-of-purchase marketing strategies for new smokeless tobacco products in 4 test market areas. A random sample of 50 gas stations, convenience and food stores, and tobacco shops was selected in each of 4 test market areas. Pairs of observers visited each store, recorded product information, and engaged vendors in conversation about product demand. Snus was available in 64% of the stores, but availability and price differed by brand. Point-of-purchase marketing also varied by brand on a variety of dimensions and all brands appeared to be marketed primarily to smokers. Camel Snus was described by store attendants as having the highest demand and was also the most expensive of the observed products. In light of the number of test market cities and intensity of promotion at retail locations, Camel Snus was the most intensively marketed product. The results appear to reflect differences in marketing strategy by American snus manufacturers. These strategies may help to predict future marketing of snus and other tobacco products and may provide a baseline for later assessments of product acceptance.

Protective properties of wine products and the role of high performance liquid chromatography in the study of these properties

International Nuclear Information System (INIS)

Ulyanova, E V; Larionov, O G; Revina, A A; Andrievskaya, D V; Urusova, L M; Fenin, A A

2013-01-01

Data on the biologically active substances present in wines and wine products, the methods of their determination, and changes under chemical, radiation and other types of action are generalized. The role of high performance liquid chromatography in the studies of the protective properties of wines is demonstrated. Particular attention is devoted to problems of counterfeiting of wine products and the possibility to reveal it by using amperometric determination of the antioxidant activity. The bibliography includes 117 references

Significance of tests and properties of concrete and concrete-making materials

CERN Document Server

Pielert, James H

2006-01-01

Reflects a decade of technological changes in concrete industry! The newest edition of this popular ASTM publication reflects the latest technology in concrete and concrete-making materials. Six sections cover: (1) General information on the nature of concrete, sampling, variability, and testing laboratories. A new chapter deals with modeling cement and concrete properties. (2) Properties of freshly mixed concrete. (3) Properties of hardened concrete. (4) Concrete aggregates—this section has been revised and the chapters are presented in the order that most concerns concrete users: grading, density, soundness, degradation resistance, petrographic examination, reactivity, and thermal properties. (5) Materials other than aggregates—the chapter on curing materials now reflects the current technology of materials applied to new concrete surfaces. The chapter on mineral admixtures has been separated into two chapters: supplementary cementitious materials and ground slag. (6) Specialized concretes—contains a ...

Estimating Aquifer Properties Using Sinusoidal Pumping Tests

Science.gov (United States)

Rasmussen, T. C.; Haborak, K. G.; Young, M. H.

2001-12-01

We develop the theoretical and applied framework for using sinusoidal pumping tests to estimate aquifer properties for confined, leaky, and partially penetrating conditions. The framework 1) derives analytical solutions for three boundary conditions suitable for many practical applications, 2) validates the analytical solutions against a finite element model, 3) establishes a protocol for conducting sinusoidal pumping tests, and 4) estimates aquifer hydraulic parameters based on the analytical solutions. The analytical solutions to sinusoidal stimuli in radial coordinates are derived for boundary value problems that are analogous to the Theis (1935) confined aquifer solution, the Hantush and Jacob (1955) leaky aquifer solution, and the Hantush (1964) partially penetrated confined aquifer solution. The analytical solutions compare favorably to a finite-element solution of a simulated flow domain, except in the region immediately adjacent to the pumping well where the implicit assumption of zero borehole radius is violated. The procedure is demonstrated in one unconfined and two confined aquifer units near the General Separations Area at the Savannah River Site, a federal nuclear facility located in South Carolina. Aquifer hydraulic parameters estimated using this framework provide independent confirmation of parameters obtained from conventional aquifer tests. The sinusoidal approach also resulted in the elimination of investigation-derived wastes.

Hydraulic properties from pumping tests data of aquifers in Azare ...

African Journals Online (AJOL)

Pumping test data from twelve boreholes in Azare area were analysed to determine the hydraulic properties of the aquifers, and the availability of water to meet the conjugate demands of the increasing population. The values of the aquifer constants obtained from the Cooper-Jacob's non-equilibrium graphical method were ...

Test methods for the dynamic mechanical properties of polymeric materials. Final report

Energy Technology Data Exchange (ETDEWEB)

Baker, G.K.

1980-06-01

Various test geometries and procedures for the dynamic mechanical analysis of polymers employing a mechanical spectrometer have been evaluated. The methods and materials included in this work are forced torsional pendulum testing of Kevlar/epoxy laminates and rigid urethane foams, oscillatory parallel plate testing to determine the kinetics of the cure of VCE with Hylene MP, oscillatory compressive testing of B-3223 cellular silicone, and oscillatory tensile testing of Silastic E and single Kevlar filaments. Fundamental dynamic mechanical properties, including the storage and loss moduli and loss tangent of the materials tested, were determined as a function of temperature and sometimes of frequency.

Electrical production testing of the D0 Silicon microstrip tracker detector modules

Energy Technology Data Exchange (ETDEWEB)

D0, SMT Production Testing Group; /Fermilab

2006-03-01

The D0 Silicon Microstrip Tracker (SMT) is the innermost system of the D0 detector in Run 2. It consists of 912 detector units, corresponding to 5 different types of assemblies, which add up to a system with 792,576 readout channels. The task entrusted to the Production Testing group was to thoroughly debug, test and grade each detector module before its installation in the tracker. This note describes the production testing sequence and the procedures by which the detector modules were electrically tested and characterized at the various stages of their assembly.

Gemfibrozil and carbamazepine decrease steroid production in zebrafish testes (Danio rerio).

Science.gov (United States)

Fraz, Shamaila; Lee, Abigail H; Wilson, Joanna Y

2018-05-01

Gemfibrozil (GEM) and carbamazepine (CBZ) are two environmentally relevant pharmaceuticals and chronic exposure of fish to these compounds has decreased androgen levels and fish reproduction in laboratory studies. The main focus of this study was to examine the effects of GEM and CBZ on testicular steroid production, using zebrafish as a model species. Chronic water borne exposures of adult zebrafish to 10 μg/L of GEM and CBZ were conducted and the dosing was confirmed by chemical analysis of water as 17.5 ± 1.78 and 11.2 ± 1.08 μg/L respectively. A 67 day exposure led to reduced reproductive output and lowered whole body, plasma, and testicular 11-ketotestosterone (11-KT). Testicular production of 11-KT was examined post exposure (42 days) using ex vivo cultures to determine basal and stimulated steroid production. The goal was to ascertain the step impaired in the steroidogenic pathway by each compound. Ex vivo 11-KT production in testes from males chronically exposed to GEM and CBZ was lower than that from unexposed males. Although hCG, 25-OH cholesterol, and pregnenolone stimulation increased 11-KT production in all treatment groups over basal levels, hCG stimulated 11-KT production remained significantly less in testes from exposed males compared to controls. 25-OH cholesterol and pregnenolone stimulated 11-KT production was similar between GEM and control groups but the CBZ group had lower 11-KT production than controls with both stimulants. We therefore propose that chronic GEM and CBZ exposure can reduce production of 11-KT in testes through direct effects independent of mediation through HPG axis. The biochemical processes for steroid production appear un-impacted by GEM exposure; while CBZ exposure may influence steroidogenic enzyme expression or function. Copyright © 2018 Elsevier B.V. All rights reserved.

Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows

CERN Document Server

American Society for Testing and Materials. Philadelphia

1999-01-01

1.1 These test methods cover the preparation and tensile testing of resin-impregnated and consolidated test specimens made from continuous filament carbon and graphite yarns, rovings, and tows to determine their tensile properties. 1.2 These test methods also cover the determination of the density and mass per unit length of the yarn, roving, or tow to provide supplementary data for tensile property calculation. 1.3 These test methods include a procedure for sizing removal to provide the preferred desized fiber samples for density measurement. This procedure may also be used to determine the weight percent sizing. 1.4 These test methods include a procedure for determining the weight percent moisture adsorption of carbon or graphite fiber. 1.5 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of t...

Properties important to mixing and simulant recommendations for WTP full-scale vessel testing

Energy Technology Data Exchange (ETDEWEB)

Poirier, M. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Martino, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-12-01

Full Scale Vessel Testing (FSVT) is being planned by Bechtel National, Inc., to demonstrate the ability of the standard high solids vessel design (SHSVD) to meet mixing requirements over the range of fluid properties planned for processing in the Pretreatment Facility (PTF) of the Hanford Waste Treatment and Immobilization Plant (WTP). Testing will use simulated waste rather than actual Hanford waste. Therefore, the use of suitable simulants is critical to achieving the goals of the test program. WTP personnel requested the Savannah River National Laboratory (SRNL) to assist with development of simulants for use in FSVT. Among the tasks assigned to SRNL was to develop a list of waste properties that are important to pulse-jet mixer (PJM) performance in WTP vessels with elevated concentrations of solids.

Authorised allergen products for intracutaneous testing may no longer be available in Germany

OpenAIRE

Klimek, Ludger; Werfel, Thomas; Vogelberg, Christian; Jung, Kirsten

2015-01-01

Background: Beside the skin prick test, the intracutaneous test represents the most important skin test method for detecting type-1 allergies. With the incorporation of European directives into national law, test allergens used for allergy diagnosis are deemed medicinal products within the meaning of the German Medicinal Products Act (Arzneimittelgesetz) and therefore require marketing authorisation for distribution in Germany. The high costs of acquiring and maintaining these authorisations ...

77 FR 49063 - Energy Conservation Program: Test Procedures for Residential Dishwashers and Cooking Products

Science.gov (United States)

2012-08-15

... Energy Conservation Program: Test Procedures for Residential Dishwashers and Cooking Products; Proposed...-AC01 Energy Conservation Program: Test Procedures for Residential Dishwashers and Cooking Products... procedures for both dishwashers and conventional cooking products for the measurement of energy use in fan...

76 FR 69585 - Testing and Labeling Pertaining to Product Certification Regarding Representative Samples for...

Science.gov (United States)

2011-11-08

... 1107 Testing and Labeling Pertaining to Product Certification Regarding Representative Samples for... [CPSC Docket No. CPSC-2011-0082] Testing and Labeling Pertaining to Product Certification Regarding... to Product Certification.'' The proposed rule was intended to implement what was then known as...

Ropivacaine alters the mechanical properties of hamstring tendons: In vitro controlled mechanical testing of tendons from living donors.

Science.gov (United States)

Ollivier, M; Sbihi, J; Sbihi, A; Pithioux, M; Parratte, S; Argenson, J-N

2017-11-01

Intraarticular or periarticular injection of ropivacaine (RI) is an element of current knee surgery practices. The goal of this study was to determine the effects of RI on the mechanical properties of hamstring tendons. We hypothesized that RI would have a detrimental effect on the mechanical properties of periarticular soft tissues METHODS: A tensile test to failure was performed on 120 hamstring tendon segments harvested during ACL reconstruction surgery in 120 patients. Two sets of tensile tests were done. The first evaluated the effect of RI itself on the mechanical properties of tendons: 30 samples were soaked for 1hour in a 2% RI solution and compared to 30 samples soaked in a saline solution (control group). The second evaluated the effect of RI concentration on the mechanical properties of hamstring tendons: 30 samples were soaked for 1hour in a 2% RI solution and 30 samples were soaked in a 7.5% RI solution. In the first test, 29 samples from each group were analyzed as two samples (one in each group) failed at the grip interface. The specimens exposed to 2% RI had lower ultimate tensile strength (Δ=4.4MPa, P=0.001), strain energy (Δ=13MPa, P=0.001) and Young's modulus (Δ=1.6MPa, P=0.02) than the specimens in the control group. There was no significant difference in the strain at failure between groups (Δ=5%, P=0.3). In the second test, one specimen from the 7.5% RI group failed during the preloading and was excluded. There was no significant difference in terms of the load at failure and ultimate tensile stress (Δ=0.45MPa, P=0.6) and strain energy (Δ=0.49MPa, P=0.49) between the two groups. There were significant differences in terms of elongation at failure (Δ=28%, P=0.0003) and Young's modulus (Δ=2.6MPa, P=0.005), with the specimens exposed to 7.5% RI undergoing greater deformation and having a lower Young's modulus. While local RI injections are widely performed in clinical practice, the results of this in vitro study point to short

A comparison of conventional mechanical testing techniques with innovative testing techniques for the evaluation of mechanical properties of NPP structural materials

International Nuclear Information System (INIS)

Liddell, P.A.; Kopriva, R.

2015-01-01

The innovative testing methods of Small Punch (SP) and Automated Ball Indentation (ABI) tests are based on the determination of material properties from sub-sized samples. These methods are promising to evaluate the components of nuclear power plants since they preserve the structural integrity of the component. The SP test is a semi-destructive method that employs miniaturised plate-shaped samples of various geometries. The method is based on the penetration of a sample with a semi-spherical punch. The sample deflection is measured throughout the test. The ABI test is a fully automatic test based on multiple indentations at a single penetration location on a polished sample surface with a spherical indenter of various diameters. The purpose of the test is to determine the tensile properties of materials in a non-destructive and localised fashion. A comparison has been made between SP, ABI and conventional tensile tests on the measurement of yield strength for the A533B (JRQ) ferritic steel which is a base metal of the pressure vessels of western PWR. The results show an excellent correlation for both innovative methods and the conventional tensile tests

25 CFR 166.814 - How will the BIA determine the value of the products or property illegally used or removed?

Science.gov (United States)

2010-04-01

... the BIA determine the value of the products or property illegally used or removed? We will determine the value of the products or property illegally used or removed based upon a valuation of similar... property illegally used or removed? 166.814 Section 166.814 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF...

Testing properties of potato starch from different scales of isolations - A ringtest

DEFF Research Database (Denmark)

Wischmann, Bente; Ahmt, T.; Bandsholm, O.

2007-01-01

and maceration of potato tubers followed by separation of starch and cell debris by sieving, filtration or sedimentation. The properties of the processed starch were analysed both in water-based systems of 10 mM NaCl as well as in a milk based food model, dutch vla. Analysis of chemical and physical properties...... included content of phosphate, protein, ash and dry weight, pH and amylopectin chain length distribution. Other analysis included starch granule size distribution, melting properties by differential scanning calorimetry (DSC), rheological properties by small deformation testing, gel pasting characteristics...... by a rapid visco analyser (RVA) and freeze/thaw stability and retrogradation characteristics analysed by pulse-NMR. Various theological flow properties were included in the analysis of the starch samples in the food model. Only the sample of starch isolated in distilled water showed significant difference...

Non-parametric tests of productive efficiency with errors-in-variables

NARCIS (Netherlands)

Kuosmanen, T.K.; Post, T.; Scholtes, S.

2007-01-01

We develop a non-parametric test of productive efficiency that accounts for errors-in-variables, following the approach of Varian. [1985. Nonparametric analysis of optimizing behavior with measurement error. Journal of Econometrics 30(1/2), 445-458]. The test is based on the general Pareto-Koopmans

P-wave velocity test for assessment of geotechnical properties of ...

Indian Academy of Sciences (India)

Administrator

P-wave velocity test, a non-destructive and easy method to apply in both field ... ditions, has increasingly been conducted to determine the geotechnical properties of rock materials. .... nent elements in the study area and rich in molds of reed ... Kocabas crystals 5–10 μm in size with no internal architecture ... organic matter.

The Development of Expansion Plug Wedge Test for Clad Tubing Structure Mechanical Property Evaluation

Energy Technology Data Exchange (ETDEWEB)

Wang, Jy-An John [ORNL; Jiang, Hao [ORNL

2016-01-12

To determine the tensile properties of irradiated fuel cladding in a hot cell, a simple test was developed at the Oak Ridge National Laboratory (ORNL) and is described fully in US Patent Application 20060070455, “Expanded plug method for developing circumferential mechanical properties of tubular materials.” This method is designed for testing fuel rod cladding ductility in a hot cell using an expandable plug to stretch a small ring of irradiated cladding material. The specimen strain is determined using the measured diametrical expansion of the ring. This method removes many complexities associated with specimen preparation and testing. The advantages are the simplicity of measuring the test component assembly in the hot cell and the direct measurement of the specimen’s strain. It was also found that cladding strength could be determined from the test results.

Test marketing for value-added root and tuber based products in ...

African Journals Online (AJOL)

Test marketing for value-added root and tuber based products in Ikwuano local government area ... JE Ewuziem, C Aniedu, E Oti, VO Onyenobi ... root and tuber based products, developed at National Root Crops Research Institute, Umudike.

Studying the co-evolution of production and test code in open source and industrial developer test processes through repository mining

NARCIS (Netherlands)

Zaidman, A.; Van Rompaey, B.; Van Deursen, A.; Demeyer, S.

2010-01-01

Many software production processes advocate rigorous development testing alongside functional code writing, which implies that both test code and production code should co-evolve. To gain insight in the nature of this co-evolution, this paper proposes three views (realized by a tool called TeMo)

Characterization of the elastic and viscoelastic properties of dentin by a nanoindentation creep test.

Science.gov (United States)

Chuang, Shu-Fen; Lin, Shih-Yun; Wei, Pal-Jen; Han, Chang-Fu; Lin, Jen-Fin; Chang, Hsien-Chang

2015-07-16

Dentin is the main supporting structure of teeth, but its mechanical properties may be adversely affected by pathological demineralization. The purposes of this study were to develop a quantitative approach to characterize the viscoelastic properties of dentin after de- and re-mineralization, and to examine the elastic properties using a nanoindentation creep test. Dentin specimens were prepared to receive both micro- and nano-indentation tests at wet and dry states. These tests were repeatedly performed after demineralization (1% citric acid for 3 days) and remineralization (artificial saliva immersion for 28 days). The nanoindentation test was executed in a creep mode, and the resulting displacement-time responses were disintegrated into primary (transient) and secondary (viscous) creep. The structural changes and mineral densities of dentin were also examined under SEM and microCT, respectively. The results showed that demineralization removed superficial minerals of dentin to the depth of 400 μm, and affected its micro- and nano-hardness, especially in the hydrate state. Remineralization only repaired the minerals at the surface layer, and partially recovered the nanohardness. Both the primary the secondary creep increased in the demineralized dentin, while the hydration further enhanced creep deformation of untreated and remineralized dentin. Remineralization reduced the primary creep of dentin, but did not effectively increase the viscosity. In conclusion, water plasticization increases the transient and viscous creep strains of demineralized dentin and reduces load sustainability. The nanoindentation creep test is capable of analyzing the elastic and viscoelastic properties of dentin, and reveals crucial information about creep responses. Copyright © 2015 Elsevier Ltd. All rights reserved.

Apollo Soyuz Test Project Weights and Mass Properties Operational Management System

Science.gov (United States)

Collins, M. A., Jr.; Hischke, E. R.

1975-01-01

The Apollo Soyuz Test Project (ASTP) Weights and Mass Properties Operational Management System was established to assure a timely and authoritative method of acquiring, controlling, generating, and disseminating an official set of vehicle weights and mass properties data. This paper provides an overview of the system and its interaction with the various aspects of vehicle and component design, mission planning, hardware and software simulations and verification, and real-time mission support activities. The effect of vehicle configuration, design maturity, and consumables updates is discussed in the context of weight control.

Setup, tests and results for the ATLAS TileCal Read Out Driver production

CERN Document Server

Valero, Alberto; Castillo, V; Cuenca, C; Ferrer, A; Fullana, E; González, V; Higón, E; Munar, A; Poveda, J; Ruiz-Martínez, A; Salvachúa, B; Sanchís, E; Solans, C; Soret, J; Torres, J; Valls, J A

2007-01-01

In this paper we describe the performance and test results of the production of the 38 ATLAS TileCal Read Out Drivers (RODs). We first describe the basic hardware specifications and firmware functionality of the modules, the test-bench setup used for production and the test procedure to qualify the boards. We then finally show and discuss the performance results.

The radiological testing of consumer products 1976-1978

International Nuclear Information System (INIS)

Wilkins, B.T.; Dixon, D.W.

1979-02-01

The National Radiological Protection Board's source testing laboratory has been operational since 1976. In the intervening period the types of consumer product which have received most attention have been ionisation chamber smoke detectors and liquid crystal digital watches containing gaseous tritium light sources; the results obtained on these two types of device are the main subject of this report. The report also traces the development of the practical appraisal of these devices by the Board and describes the part played by the test results in the evolution of national and international standards. (author)

Measurement of the jet production properties at the LHC with the ATLAS Detector

CERN Document Server

Tokar, Stanislav; The ATLAS collaboration

2015-01-01

Latest results on the jet production properties obtained by the ATLAS experiment are presented. Jet physics events produced in pp collisions at 7 TeV have been studied. The dijet double differential cross sections as a function of dijet invariant mass for different rapidity regions are reported. Dijet flavour decomposition, a lower limit on the quark compositeness scale, inclusive jet production differential cross sections, three-jet differential production cross sections as well as a measurement of jet shapes for b-jets and light jets from top quark pair events are also reported.

The safety of food products requires X-ray testing

International Nuclear Information System (INIS)

Lardiere, C.

2017-01-01

Food safety through standards and regulations imposes food products to be tested for the presence of alien elements. So far metal detectors have been used to detect metal parts, now they have been progressively replaced with X-ray scanners that allow the detection of a lot more contaminants. The improvement of algorithms for image processing combined with the availability of ever more powerful PC have led to the routine use of X-ray testing on industrial processes. Technological progress has made X-ray testing more efficient: while previously a power of 500 W was necessary to cross a 10 cm thickness of water, now only 100 W is necessary. The main advantage of X-ray testing is to be able to test food even packed in metal containers and to detect if the container is deformed. Another advantages is to be able to detect a lot of elements like pieces of glass, small stones or bits of bones. The minimal size to be detected is 0.5 mm for stainless steels and 2 mm for glass or bones. Usually metal detectors are set at the end of the production line just before packaging but in some cases they can be included in the line in order to protect the next machine that intervenes to process the food. (A.C.)

Fenugreek: A review on its nutraceutical properties and utilization in various food products

Directory of Open Access Journals (Sweden)

Sajad Ahmad Wani

2018-04-01

Full Text Available Fenugreek (Trigonella foenum-graecum is a legume and it has been used as a spice throughout the world to enhance the sensory quality of foods. It is known for its medicinal qualities such as antidiabetic, anticarcinogenic, hypocholesterolemic, antioxidant, and immunological activities. Beside its medicinal value, it is also used as a part of various food product developments as food stabilizer, adhesive, and emulsifying agent. More importantly it is used for the development of healthy and nutritious extruded and bakery product. The present paper reviews about nutraceutical properties of fenugreek and its utilization in various product developments. Keywords: Fenugreek, Nutraceutical, Hypoglycemic, Antioxidant, Extruded product

40 CFR 1045.305 - How must I prepare and test my production-line engines?

Science.gov (United States)

2010-07-01

... production-line engines? 1045.305 Section 1045.305 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND VESSELS Testing Production-line Engines § 1045.305 How must I prepare and test my production-line engines...

40 CFR 1048.305 - How must I prepare and test my production-line engines?

Science.gov (United States)

2010-07-01

... production-line engines? 1048.305 Section 1048.305 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, LARGE NONROAD SPARK-IGNITION ENGINES Testing Production-line Engines § 1048.305 How must I prepare and test my production-line engines? This...

77 FR 9859 - Lifesaving Equipment: Production Testing and Harmonization With International Standards

Science.gov (United States)

2012-02-21

... Prototype testing.... Manufacturers must obtain Units with rated All tests use the Units with rated (160.151... Liferafts Prototype testing.... Existing Certificates of No cost or benefit as All tests use the Costs of... designs, overseeing prototype construction, witnessing prototype testing, and monitoring production of the...

Quantum Property Testing

NARCIS (Netherlands)

H. Buhrman (Harry); L. Fortnow (Lance); I. Newman; H. Röhrig (Hein)

2008-01-01

textabstractA language $L$ has a property tester if there exists a probabilistic algorithm that given an input $x$ queries only a small number of bits of $x$ and distinguishes the cases as to whether $x$ is in $L$ and $x$ has large Hamming distance from all $y$ in $L$. We define a similar notion of

Formation and properties of radiation-induced defects and radiolysis products in lithium orthosilicate

Energy Technology Data Exchange (ETDEWEB)

Tiliks, J.E.; Kizane, G.K.; Supe, A.A.; Abramenkovs, A.A.; Tiliks, J.J. (Latvian Univ., Riga (Latvia)); Vasiljev, V.G. (Acad. A.A. Bochvar Inst. of Inorganic Materials, Moscow (USSR))

1991-12-01

Formation and properties of radiation-induced defects and radiolysis products in polycrystalline powders and ceramic pellets of Li{sub 4}SiO{sub 4} were studied under the effect of various types of ionizing irradiation ({gamma} quants, accelerated electrons, reactor irradiation), humidity, temperature, impurities in the samples, etc. The content of radiation defects and radiolysis products poorly depends on irradiation type, dose rate, admixture elements. The concentration of defects highly depends on the temperature of irradiation, humidity, granural size. Empirical dependence of radiolysis degree {alpha} on the dose was found: {alpha}=5x10{sup -2}xD{sup 0.5} for {gamma} and electron irradiation (T{sub rad}=300-350 K) and {alpha}=5x10{sup -3}xD{sup 0.5} for reactor radiation (T{sub rad}=700-800 K); {alpha} - matrix dissociation degree (in %); D - dose (in MGy). Colloidal lithium and silicon, lithium and silicon oxides, and O{sub 2} are the final products of radiolysis. Radiation-induced defects change tritium thermo-extraction parameters, deteriorate mechanical, thermo-physical and electric properties of ceramics. (orig.).

Justification of the Production Process of Pressed Wood and Study of its Properties

Science.gov (United States)

Polilov, A. N.; Dornyak, O. R.; Shamaev, V. A.; Rumachik, M. M.

2018-05-01

Results of a numerical analysis of the stress-strain state of wood during its pressing in different symmetry directions of the anisotropic material are presented. It is shown that the anisotropy of mechanical properties of wood is an important factor determining both the structural characteristics of the porous system and its strength. A mathematical modeling of the process of pressing wood as a three-phase anisotropic rheologically complex capillary-porous system allows one to predict parameters of the resulting wood composite. The compressed wood obtained by the production modes developed has a tensile strength eight times greater than that of the natural one, which is comparable to the strength of the St3 steel, but its specific strength is higher than that of the St45 steel. Compression and impregnation of softwood species with an aqueous solution of carbamide allows one to harden them. This kind of treatment endows the wood with enhanced strength characteristics comparable to the characteristics of the St3 steel. The special features of tensile tests used to estimate the elastic modulus and strength characteristics of such materials are considered. Data obtained by different testing methods are correlated, and characteristics of the strengthened wood and some brends of steel are compared.

Production Facility Prototype Blower 1000 Hour Test Results II

Energy Technology Data Exchange (ETDEWEB)

Wass, Alexander Joseph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Woloshun, Keith Albert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dale, Gregory E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dalmas, Dale Allen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Romero, Frank Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-08

Long duration tests of the Aerzen GM 12.4 roots style blower in a closed loop configuration provides valuable data and lessons learned for long-term operation at the Mo-99 production facility. The blower was operated in a closed loop configuration with the flow conditions anticipated in plant operation with a Mo-100 target inline. The additional thermal energy generated from beam heating of the Mo-100 disks were not included in these tests. Five 1000 hour tests have been completed since the first test was performed in January of 2016. All five 1000 hour tests have proven successful in exposing preventable issues related to oil and helium leaks. All blower tests to this date have resulted in stable blower performance and consistency. A summary of the results for each test, including a review of the first and second tests, are included in this report.

Well test: production analysis and allocation measurement; Teste de poco: analise da producao e medicao de apropriacao

Energy Technology Data Exchange (ETDEWEB)

Geron, Luis Carlos [Smar Equipamentos Industriais Ltda., Sertaozinho, SP (Brazil). Dept. de Engenharia Aplicacoes; Tateishi, Sergio Hideki [Smar Equipamentos Industriais Ltda, Sertaozinho, SP (Brazil). Dept. de Pesquisa e Desenvolvimento

2008-07-01

The well test is an instrument frequently used to evaluate the production capacity of wells and it usually has specific requirements in the flow measurement, that are not necessary in the flow measurement system for custody transfer applications. Starting with the requirement to measure the injected product in the well when it is in the recuperation phase and it also includes compliance to specific standards for allocation measurement, because these hydrocarbon products are not treated as well as that ones in the production streams. Other important issue associated to the well test is the employment of new technologies, that helps to reduce the uncertainty of measurement as digital communication between the field devices and the flow computer through an open protocol as the Foundation Field bus. Another indication of technology evolution in the flow measurement focusing a lower uncertainty is the new version of API MPMS 11.1:2004, that requires calculation with double precision floating point, as well the correction factors with 5 decimal digits. (author)

Tensile properties of orthodontic elastomeric ligatures.

Science.gov (United States)

Ahrari, F; Jalaly, T; Zebarjad, M

2010-01-01

Tensile properties of elastomeric ligatures become important when efficiency of orthodontic appliances is considered. The aim of this study was to compare tensile strength, extension to tensile strength, toughness and modulus of elasticity of elastomeric ligatures in both the as--received condition and after 28 days of immersion in the simulated oral environment. Furthermore, the changes that occurred in tensile properties of each brand of ligatures after 28 days were evaluated. Experimental-laboratory based. Elastomeric ligatures were obtained from different companies and their tensile properties were measured using Zwick testing machine in both the as-received condition and after 28 days of immersion in the simulated oral environment. The data were analyzed using independent sample t-tests, analysis of variance and Tukey tests. After 28 days, all the ligatures experienced a significant decrease in tensile strength, extension to tensile strength and toughness ( P tensile properties of different brands of ligatures in both conditions ( P tensile properties of different brands of ligatures, which should be considered during selection of these products.

Effects of Medium Temperature and Industrial By-Products on the Key Hardened Properties of High Performance Concrete

Science.gov (United States)

Safiuddin, Md.; Raman, Sudharshan N.; Zain, Muhammad Fauzi Mohd.

2015-01-01

The aim of the work reported in this article was to investigate the effects of medium temperature and industrial by-products on the key hardened properties of high performance concrete. Four concrete mixes were prepared based on a water-to-binder ratio of 0.35. Two industrial by-products, silica fume and Class F fly ash, were used separately and together with normal portland cement to produce three concrete mixes in addition to the control mix. The properties of both fresh and hardened concretes were examined in the laboratory. The freshly mixed concrete mixes were tested for slump, slump flow, and V-funnel flow. The hardened concretes were tested for compressive strength and dynamic modulus of elasticity after exposing to 20, 35 and 50 °C. In addition, the initial surface absorption and the rate of moisture movement into the concretes were determined at 20 °C. The performance of the concretes in the fresh state was excellent due to their superior deformability and good segregation resistance. In their hardened state, the highest levels of compressive strength and dynamic modulus of elasticity were produced by silica fume concrete. In addition, silica fume concrete showed the lowest level of initial surface absorption and the lowest rate of moisture movement into the interior of concrete. In comparison, the compressive strength, dynamic modulus of elasticity, initial surface absorption, and moisture movement rate of silica fume-fly ash concrete were close to those of silica fume concrete. Moreover, all concretes provided relatively low compressive strength and dynamic modulus of elasticity when they were exposed to 50 °C. However, the effect of increased temperature was less detrimental for silica fume and silica fume-fly ash concretes in comparison with the control concrete. PMID:28793732

Effects of Medium Temperature and Industrial By-Products on the Key Hardened Properties of High Performance Concrete.

Science.gov (United States)

Safiuddin, Md; Raman, Sudharshan N; Zain, Muhammad Fauzi Mohd

2015-12-10

The aim of the work reported in this article was to investigate the effects of medium temperature and industrial by-products on the key hardened properties of high performance concrete. Four concrete mixes were prepared based on a water-to-binder ratio of 0.35. Two industrial by-products, silica fume and Class F fly ash, were used separately and together with normal portland cement to produce three concrete mixes in addition to the control mix. The properties of both fresh and hardened concretes were examined in the laboratory. The freshly mixed concrete mixes were tested for slump, slump flow, and V-funnel flow. The hardened concretes were tested for compressive strength and dynamic modulus of elasticity after exposing to 20, 35 and 50 °C. In addition, the initial surface absorption and the rate of moisture movement into the concretes were determined at 20 °C. The performance of the concretes in the fresh state was excellent due to their superior deformability and good segregation resistance. In their hardened state, the highest levels of compressive strength and dynamic modulus of elasticity were produced by silica fume concrete. In addition, silica fume concrete showed the lowest level of initial surface absorption and the lowest rate of moisture movement into the interior of concrete. In comparison, the compressive strength, dynamic modulus of elasticity, initial surface absorption, and moisture movement rate of silica fume-fly ash concrete were close to those of silica fume concrete. Moreover, all concretes provided relatively low compressive strength and dynamic modulus of elasticity when they were exposed to 50 °C. However, the effect of increased temperature was less detrimental for silica fume and silica fume-fly ash concretes in comparison with the control concrete.

Effects of Medium Temperature and Industrial By-Products on the Key Hardened Properties of High Performance Concrete

Directory of Open Access Journals (Sweden)

Md. Safiuddin

2015-12-01

Full Text Available The aim of the work reported in this article was to investigate the effects of medium temperature and industrial by-products on the key hardened properties of high performance concrete. Four concrete mixes were prepared based on a water-to-binder ratio of 0.35. Two industrial by-products, silica fume and Class F fly ash, were used separately and together with normal portland cement to produce three concrete mixes in addition to the control mix. The properties of both fresh and hardened concretes were examined in the laboratory. The freshly mixed concrete mixes were tested for slump, slump flow, and V-funnel flow. The hardened concretes were tested for compressive strength and dynamic modulus of elasticity after exposing to 20, 35 and 50 °C. In addition, the initial surface absorption and the rate of moisture movement into the concretes were determined at 20 °C. The performance of the concretes in the fresh state was excellent due to their superior deformability and good segregation resistance. In their hardened state, the highest levels of compressive strength and dynamic modulus of elasticity were produced by silica fume concrete. In addition, silica fume concrete showed the lowest level of initial surface absorption and the lowest rate of moisture movement into the interior of concrete. In comparison, the compressive strength, dynamic modulus of elasticity, initial surface absorption, and moisture movement rate of silica fume-fly ash concrete were close to those of silica fume concrete. Moreover, all concretes provided relatively low compressive strength and dynamic modulus of elasticity when they were exposed to 50 °C. However, the effect of increased temperature was less detrimental for silica fume and silica fume-fly ash concretes in comparison with the control concrete.

Effects of NaCl Replacement with Gamma-Aminobutyric acid (GABA) on the Quality Characteristics and Sensorial Properties of Model Meat Products

Science.gov (United States)

Chun, Ji-Yeon; Cho, Hyung-Yong; Min, Sang-Gi

2014-01-01

This study investigated the effects of γ-aminobutylic acid (GABA) on the quality and sensorial properties of both the GABA/NaCl complex and model meat products. GABA/NaCl complex was prepared by spray-drying, and the surface dimensions, morphology, rheology, and saltiness were characterized. For model meat products, pork patties were prepared by replacing NaCl with GABA. For characteristics of the complex, increasing GABA concentration increased the surface dimensions of the complex. However, GABA did not affect the rheological properties of solutions containing the complex. The addition of 2% GABA exhibited significantly higher saltiness than the control (no GABA treatment). In the case of pork patties, sensory testing indicated that the addition of GABA decreased the saltiness intensity. Both the intensity of juiciness and tenderness of patties containing GABA also scored lower than the control, based on the NaCl reduction. These results were consistent with the quality characteristics (cooking loss and texture profile analysis). Nevertheless, overall acceptability of the pork patties showed that up to 1.5%, patties containing GABA did not significantly differ from the control. Consequently, the results indicated that GABA has a potential application in meat products, but also manifested a deterioration of quality by the NaCl reduction, which warrants further exploration. PMID:26761294

Performance test results of mock-up model test facility with a full-scale reaction tube for HTTR hydrogen production system. Contract research

Energy Technology Data Exchange (ETDEWEB)

Inagaki, Yoshiyuki; Hayashi, Koji; Kato, Michio [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment] [and others

2003-03-01

Research on a hydrogen production system by steam reforming of methane, chemical reaction; CH{sub 4} + H{sub 2}O {yields} 3H{sub 2}O + CO, has been carried out to couple with the HTTR for establishment of high-temperature nuclear heat utilization technology and contribution to hydrogen energy society in future. The mock-up test facility with a full-scale reaction tube test facility, a model simulating one reaction tube of a steam reformer of the HTTR hydrogen production system in full scale, was fabricated to perform tests on controllability, hydrogen production performance etc. under the same pressure and temperature conditions as those of the HTTR hydrogen production system. The design and fabrication of the test facility started from 1997, and the all components were installed until September in 2001. In a performance test conducted from October in 2001 to February in 2002, performance of each component was examined and hydrogen of 120m{sup 3}{sub N}/h was successfully produced with high-temperature helium gas. This report describes the performance test results on components performance, hydrogen production characteristics etc., and main troubles and countermeasures. (author)

Performance test results of mock-up model test facility with a full-scale reaction tube for HTTR hydrogen production system. Contract research

International Nuclear Information System (INIS)

Inagaki, Yoshiyuki; Hayashi, Koji; Kato, Michio

2003-03-01

Research on a hydrogen production system by steam reforming of methane, chemical reaction; CH 4 + H 2 O → 3H 2 O + CO, has been carried out to couple with the HTTR for establishment of high-temperature nuclear heat utilization technology and contribution to hydrogen energy society in future. The mock-up test facility with a full-scale reaction tube test facility, a model simulating one reaction tube of a steam reformer of the HTTR hydrogen production system in full scale, was fabricated to perform tests on controllability, hydrogen production performance etc. under the same pressure and temperature conditions as those of the HTTR hydrogen production system. The design and fabrication of the test facility started from 1997, and the all components were installed until September in 2001. In a performance test conducted from October in 2001 to February in 2002, performance of each component was examined and hydrogen of 120m 3 N /h was successfully produced with high-temperature helium gas. This report describes the performance test results on components performance, hydrogen production characteristics etc., and main troubles and countermeasures. (author)

Functional properties of plantain, cowpea flours and oat fiber in extruded products

Science.gov (United States)

Drying effect on functional properties of two plantain and cowpea varieties and suitability of their flour blends in extruded snacks was determined. The functional and rheological behaviors of (plantain: cowpea): 90:10, 80:20, 70:30, 60:40 and 50:50 blends were evaluated. The extrusion product melt ...

The use of averages and other summation quantities in the testing of evaluated fission product yield and decay data. Applications to ENDF/B(IV)

International Nuclear Information System (INIS)

Walker, W.H.

1976-01-01

Averages of some fission product properties can be obtained by multiplying the fission product yield for each fission product by the value of the property (e.g. mass, atomic number, mass defect) for that fission product and summing all significant contributions. These averages can be used to test the reliability of the yield set or provide useful data for reactor calculations. The report gives the derivation of these averages and discusses their application using the ENDF/B(IV) fission product library. The following quantities are treated here: the number of fission products per fission ΣYsub(i); the average mass number and the average number of neutrons per fission; the average atomic number of the stable fission products and the average number of β-decays per fission; the average mass defect of the stable fission products and the total energy release per fission; the average decay energy per fission (beta, gamma and anti-neutrino); the average β-decay energy per fission; individual and group-averaged delayed neutron emission; the total yield for each fission product element. Wherever it is meaningful to do so, a sum is subdivided into its light and heavy mass components. The most significant differences between calculated values based on ENDF/B(IV) and measurements are the β and γ decay energies for 235 U thermal fission and delayed neutron yields for other fissile nuclides, most notably 238 U. (author)

A comparison of the mechanical and sensory properties of baked and extruded confectionery products

Science.gov (United States)

Butt, Saba; Charalambides, Maria; Mohammed, Idris K.; Powell, Hugh

2017-10-01

Traditional baking is the most common way of producing confectionery wafers, however over the past few decades, the extrusion process has become an increasingly important food manufacturing method and is commonly used in the manufacturing of breakfast cereals and filled snack products. This study aims to characterise products made via each of these manufacturing processes in order to understand the important parameters involved in the resulting texture of confectionery products such as wafers. Both of the named processes result in brittle, cellular foams comprising of cell walls and cell pores which may contain some of the confectionery filling. The mechanical response of the cell wall material and the geometry of the products influence the consumer perception and preference. X-Ray micro tomography (XRT) was used to generate geometry of the microstructure which was then fed to Finite Element (FE) for numerical analysis on both products. The FE models were used to determine properties such as solid modulus of the cell walls, Young's modulus of the entire foam and to investigate and compare the microstructural damage of baked wafers and extruded products. A sensory analysis study was performed on both products by a qualified sensory panel. The results of this study were then used to draw links between the mechanical behaviour and sensory perception of a consumer. The extruded product was found to be made up of a stiffer solid material and had a higher compressive modulus and fracture stress when compared to the baked wafer. The sensory panel observed textural differences between the baked and extruded products which were also found in the differences of the mechanical properties of the two products.

Surface tension and wetting properties of rapeseed oil to biofuel conversion by-products

Science.gov (United States)

Muszyński, Siemowit; Sujak, Agnieszka; Stępniewski, Andrzej; Kornarzyński, Krzysztof; Ejtel, Marta; Kowal, Natalia; Tomczyk-Warunek, Agnieszka; Szcześniak, Emil; Tomczyńska-Mleko, Marta; Mleko, Stanisław

2018-04-01

This work presents a study on the surface tension, density and wetting behaviour of distilled glycerol, technical grade glycerol and the matter organic non-glycerin fraction. The research was conducted to expand the knowledge about the physical properties of wastes from the rapeseed oil biofuel production. The results show that the densities of technical grade glycerol (1.300 g cm-3) and distilled glycerol (1.267 g cm-3) did not differ and were significantly lower than the density of the matter organic non-glycerin fraction (1.579 g cm-3). Furthermore, the surface tension of distilled glycerol (49.6 mN m-1) was significantly higher than the matter organic non-glycerin fraction (32.7 mN m-1) and technical grade glycerol (29.5 mN m-1). As a result, both technical grade glycerol and the matter organic non-glycerin fraction had lower contact angles than distilled glycerol. The examined physical properties of distilled glycerol were found to be very close to that of the commercially available pure glycerol. The results suggest that technical grade glycerol may have potential application in the production of glycerol/fuel blends or biosurfactants. The presented results indicate that surface tension measurements are more useful when examining the quality of biofuel wastes than is density determination, as they allow for a more accurate analysis of the effects of impurities on the physical properties of the biofuel by-products.

Calcium carbonate synthesis with prescribed properties based on liquid waste of soda production

OpenAIRE

E.O. Mikhailova; V.O. Panasenko; N.B. Markova

2016-01-01

A promising direction in solving of environmental problems of soda industry is the development of low-waste resource-saving technologies, which consist in recycling of valuable waste components with obtaining the commercial products. Aim: The aim is to establish the optimal conditions for obtaining calcium carbonate with prescribed properties from liquid waste of soda production. Materials and Methods: Chemically deposited calcium carbonate is used as filler and should have certain physical a...

Nutritional composition in the chia seed and its processing properties on restructured ham-like products

Directory of Open Access Journals (Sweden)

Yi Ding

2018-01-01

Full Text Available Low-fat meat products always have harder texture, lower juiciness, and worse flavor. Due to their higher water-holding, water absorption, and organic molecule absorption, chia seeds (CHIA have been applied in powders, nutrition bars, breads, and cookies. Hence, the objectives of this study were to: (1 analyze the nutritional compositions in CHIA; and (2 look for the possible application of CHIA on restructured ham-like products. CHIA has high amounts of α-linolenic acid, crude polysaccharides, and also contains essential amino acids, minerals, and polyphenols. Regarding processing properties of CHIA, a combination of CHIA and carrageenan (CA increased (p<0.05 production yield of restructured ham-like products. A scanning electron microscope observation indicated that CHIA and CA addition can assist an emulsification in this ham-like product. Addition of 0.5% CA and 1.0% CHIA in this ham-like product showed the similar overall acceptance as products with added fat. Following storage at 4°C, higher (p<0.05 purge and centrifugation losses, as well as hardness of this ham-like product can be improved by adding CHIA and CA. CHIA addition also resulted in lower (p<0.05 lipid and protein oxidation, especially a 1.0% addition. In summary, due to both nutritional addition and improvements on physicochemical and sensorial properties of restructured ham-like products, CHIA seeds have great potential on the development of healthy and good-quality meat products.

Earthworm cast production as a new behavioural biomarker for toxicity testing

Energy Technology Data Exchange (ETDEWEB)

Capowiez, Yvan, E-mail: capowiez@avignon.inra.f [INRA, UR1115 ' Plantes et Systemes Horticoles' , Domaine Saint Paul, 84914 Avignon Cedex 09 (France); Dittbrenner, Nils [INRA, UR1115 ' Plantes et Systemes Horticoles' , Domaine Saint Paul, 84914 Avignon Cedex 09 (France); Animal Physiological Ecology, University of Tuebingen, Konrad-Adenauer-Str. 20, D-72072 Tuebingen (Germany); Rault, Magali [UAPV, UMR406 ' Abeilles et Environnement' , Domaine Saint Paul, 84914 Avignon Cedex 09 (France); Triebskorn, Rita [Animal Physiological Ecology, University of Tuebingen, Konrad-Adenauer-Str. 20, D-72072 Tuebingen (Germany); Hedde, Mickael [INRA, UR251 ' PESSAC' , RD10, 78026 Versailles Cedex (France); Mazzia, Christophe [UAPV, UMR406 ' Abeilles et Environnement' , Domaine Saint Paul, 84914 Avignon Cedex 09 (France)

2010-02-15

There is currently a lack of ecotoxicity tests adapted to earthworm species of higher ecological relevance and whose endpoints could be directly related to their ecological role in the soil. We propose a new and relatively simple ecotoxicity test based on the estimation of cast production (CP) by Lumbricus terrestris under laboratory conditions. CP was found to be linearly correlated to earthworm biomass and to be greatly influenced by soil water content. Azinphos-methyl had no effect on CP at all the concentrations tested. Significant decreases were observed at the normal application rate for other pesticides with (imidacloprid, carbaryl, methomyl) or without (ethyl-parathion and chlorpyrifos-ethyl) a clear concentration-effect response. For the highest concentration tested, reduction in CP varied between 35 and 67%. CP is straightforward and rapidly measured and ecologically meaningful. We thus believe it to be of great use as an endpoint in ecotoxicity testing. - Cast production of Lumbricus terrestris is affected by pesticides under laboratory conditions.

Earthworm cast production as a new behavioural biomarker for toxicity testing

International Nuclear Information System (INIS)

Capowiez, Yvan; Dittbrenner, Nils; Rault, Magali; Triebskorn, Rita; Hedde, Mickael; Mazzia, Christophe

2010-01-01

There is currently a lack of ecotoxicity tests adapted to earthworm species of higher ecological relevance and whose endpoints could be directly related to their ecological role in the soil. We propose a new and relatively simple ecotoxicity test based on the estimation of cast production (CP) by Lumbricus terrestris under laboratory conditions. CP was found to be linearly correlated to earthworm biomass and to be greatly influenced by soil water content. Azinphos-methyl had no effect on CP at all the concentrations tested. Significant decreases were observed at the normal application rate for other pesticides with (imidacloprid, carbaryl, methomyl) or without (ethyl-parathion and chlorpyrifos-ethyl) a clear concentration-effect response. For the highest concentration tested, reduction in CP varied between 35 and 67%. CP is straightforward and rapidly measured and ecologically meaningful. We thus believe it to be of great use as an endpoint in ecotoxicity testing. - Cast production of Lumbricus terrestris is affected by pesticides under laboratory conditions.

Preliminary assessment of the waveform inversion method for interpretation of cross-well seismic data from the thermal production test, JAPEX/JNOC/GSC et al. Mallik 5L-38 gas hydrate production research well

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T. [Nagoya Univ., Nagoya (Japan). Research Center for Seismology and Volcanology; Shimizu, S. [Japan National Oil Co., Chiba (Japan); Asakawa, E. [JGI Inc., Tokyo (Japan); Kamei, R.; Matsuoka, T. [Kyoto Univ., Kyoto (Japan). Dept. of Civil and Earth Resources Engineering

2005-07-01

The JAPEX/JNOC/GSC et al. Mallik 3L-38 and 4L-38 test wells were subjected to repeated cross-well seismic surveys before and during the gas production test from the gas-hydrate-bearing layer at a depth of about 905 to 920 m. High-resolution velocity images in the gas-hydrate-bearing layer were obtained using the frequency-domain nonlinear waveform inversion method. An acoustic waveform inversion method was used along with the frequency-domain approach in order to detect the change in acoustic properties of the gas-hydrate-bearing layer resulting from gas production. The layered structures with small lateral heterogeneities were reconstructed by tomography analysis of preprocessed waveform data using a smaller number of source-receiver pairs. Preliminary results reveal high velocity and very high attenuation in the gas-hydrate-bearing layers. No obvious velocity decreases were noted. Information for further detailed processing was also gathered.

Testing knowledge of whole English collocations available for use in written production

DEFF Research Database (Denmark)

Revier, Robert Lee

2014-01-01

Testing knowledge of whole English collocations available for use in written production: Developing tests for use with intermediate and advanced Danish learners (dansk resume nedenfor) The present foreign language acquisition research derives its impetus from four assumptions regarding knowledge...... of English collocations. These are: (a) collocation knowledge can be conceptualized as an independent knowledge construct, (b) collocations are lexical items in their own right, (c) testing of collocation knowledge should also target knowledge of whole collocations, and (d) the learning burden of a whole...... the development of Danish EFL learners’ productive knowledge of whole English collocations. Five empirical studies were designed to generate information that would shed light on the reliability and validity of the CONTRIX as a measure of collocation knowledge available for use in written production. Study 1...

46 CFR 54.20-5 - Welding qualification tests and production testing (modifies UW-26, UW-28, UW-29, UW-47, and UW-48).

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Welding qualification tests and production testing... OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Fabrication by Welding § 54.20-5 Welding qualification tests and production testing (modifies UW-26, UW-28, UW-29, UW-47, and UW-48). (a...

Analysis of the rock mechanics properties of volcanic tuff units from Yucca Mountain, Nevada Test Site

International Nuclear Information System (INIS)

Price, R.H.

1983-08-01

Over two hundred fifty mechanical experiments have been run on samples of tuff from Yucca Mountain, Nevada Test Site. Cores from the Topopah Spring, Calico Hills, Bullfrog and Tram tuff units were deformed to collect data for an initial evaluation of mechanical (elastic and strength) properties of the potential horizons for emplacement of commercial nuclear wastes. The experimental conditions ranged in sample saturation from room dry to fully saturated, confining pressure from 0.1 to 20 MPa, pore pressure from 0.1 to 5 MPa, temperature from 23 to 200 0 C, and strain rate from 10 -7 to 10 -2 s -1 . These test data have been analyzed for variations in elastic and strength properties with changes in test conditions, and to study the effects of bulk-rock characteristics on mechanical properties. In addition to the site-specific data on Yucca Mountain tuff, mechanical test results on silicic tuff from Rainier Mesa, Nevada Test Site, are also discussed. These data both overlap and augment the Yucca Mountain tuff data, allowing more definitive conclusions to be reached, as well as providing data at some test conditions not covered by the site-specific tests

46 CFR 159.007-11 - Production inspections and tests: Yearly report.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Production inspections and tests: Yearly report. 159.007-11 Section 159.007-11 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL APPROVAL OF EQUIPMENT AND MATERIALS Production...

Urea-formaldehyde resins: production, application, and testing

Science.gov (United States)

Nuryawan, A.; Risnasari, I.; Sucipto, T.; Heri Iswanto, A.; Rosmala Dewi, R.

2017-07-01

Urea-formaldehyde (UF) resin, one of the most important formaldehyde resin adhesives, is a polymeric condensation product of formaldehyde with urea, and being widely used for the manufacture of wood-based composite panels, such as plywood, particleboard, and fiberboard. In spite of its benefits such as fast curing, good performance in the panels (colorless), and lower cost; formaldehyde emission (FE) originated from either UF resin itself or composite products bonded by UF resins is considered a critical drawback as it affects human health particularly in indoor environment. In order to reduce the FE, lowering formaldehyde/urea (F/U) mole ratio in the synthesis of the UF resin was done. In this study, synthesis of UF resins was carried out following the conventional alkaline-acid two-step reaction with a second addition of urea, resulting in F/U mole ratio around 1.0, namely 0.95; 1.05, and 1.15. The UF resins produced were used as binder for particleboard making. The board was manufactured in the laboratory using shaving type particle of Gmelina wood, 8% UF resin based on oven dry particle, and 1% NH4Cl (20%wt) as hardener for the resin. The target of the thickness was 10 mm and the dimension was 25 cm x 25 cm. The resulted particleboard then was evaluated the physical and the mechanical properties by Japanese Industrial Standard (JIS) A 5908 (2003). Further, the resulted particleboard also was used for the mice cage’s wall in order to mimic the real living environment. After four weeks exposure in the cages, the mice then were evaluated their mucous organs as well as their blood. The experiment results were as follows: 1) It was possible to synthesis UF resins with low F/U mole ratio; 2) However, the particleboard bonded UF resins with low F/U mole ratio showed poor properties, particularly on the thickness swelling and modulus of elasticity; 3) There was no significant differences among the mucous organs of the mice after a month exposure FE originated from

Differential properties and attracting sets of a simplest skew product of interval maps

International Nuclear Information System (INIS)

Efremova, Lyudmila S

2010-01-01

For a skew product of interval maps with a closed set of periodic points, the dependence of the structure of its ω-limit sets on its differential properties is investigated. An example of a map in this class is constructed which has the maximal differentiability properties (within a certain subclass) with respect to the variable x, is C 1 -smooth in the y-variable and has one-dimensional ω-limit sets. Theorems are proved that give necessary conditions for one-dimensional ω-limit sets to exist. One of them is formulated in terms of the divergence of the series consisting of the values of a function of x; this function is the C 0 -norm of the deviation of the restrictions of the fibre maps to some nondegenerate closed interval from the identity on the same interval. Another theorem is formulated in terms of the properties of the partial derivative with respect to x of the fibre maps. A complete description is given of the ω-limit sets of certain class of C 1 -smooth skew products satisfying some natural conditions. Bibliography: 33 titles.

The chemical composition and parameters of production processes influence on structure and properties of W-Ni-Fe alloys

International Nuclear Information System (INIS)

Majewski, T.; Przetakiewicz, W.

2000-01-01

Tungsten heavy alloys, i.e. tungsten based metal-matrix composites are characterized by unique properties, because except their high hardness, strength and density, they also possess excellent ductility, impact strength, machinability and corrosion resistance. This combination of properties makes these alloys suitable for wide range of engineering applications, e.g. in the mechanical engineering, in the mining, sport and medicine and also in the armament and aviation. Production process of these materials consists of many phases and it is very difficult to accomplish, because properties of heavy alloys are extremely sensitive to processing history. In this article dependence of chemical composition of mixture of powders on structure and mechanical properties of W-Ni-Fe alloys was determined. It was found that increase of tungsten contents and Ni/Fe ratio causes reduction of ductility and increase of growth rate of tungsten particle. There is the maximum ultimate tensile strength of W-Ni-Fe alloys with content of tungsten 93%. The study also presents relationship between these properties and succeeding parameters of production process: composition of sintering atmosphere, time and temperature following heat treatment and plastic working. Using a wet hydrogen atmosphere (with high dew point) causes reduction of porosity and improvement of mechanical properties. With sintering temperature above 1500 o C these parameters decrease. If the sintering time is elongated above 1 h also density and mechanical properties of heavy alloys decrease. Tungsten heavy alloys are also used for production of kinetic energy penetrators and so properties for different range of strain rates were compared. It was found that yield and failure strengths increase with increasing strain rate, failure strain decreases with increasing strain rate. This information can help in optimization the production process of such composites. (author)

Theoretical and experimental methods to determine the properties of molten core components and reaction products. Pt. 2

International Nuclear Information System (INIS)

Nazare, S.; Ondracek, G.; Schulz, B.

1975-10-01

In the course of a loss of coolant accident, a sequence of events would be initiated that ultimately could lead to core melting. The course of these events and the consequences of core meltdown would in part be determined by the properties of the core materials and the products of their interaction. On the basis of available theoretical and experimental results, the report attempts an estimation of properties such as: 1) work of adhesion between UO 2 - and (U,Zr) liquid phase, 2) heat of fusion of some melts, 3) heat capacity of liquid reaction products, 4) viscosity of liquid reaction products, 5) thermal conductivity of liquid reaction products. Experimental work is suggested for those cases, where the estimates need to be improved or verified. (orig.) [de

Process design of press hardening with gradient material property influence

International Nuclear Information System (INIS)

Neugebauer, R.; Schieck, F.; Rautenstrauch, A.

2011-01-01

Press hardening is currently used in the production of automotive structures that require very high strength and controlled deformation during crash tests. Press hardening can achieve significant reductions of sheet thickness at constant strength and is therefore a promising technology for the production of lightweight and energy-efficient automobiles. The manganese-boron steel 22MnB5 have been implemented in sheet press hardening owing to their excellent hot formability, high hardenability, and good temperability even at low cooling rates. However, press-hardened components have shown poor ductility and cracking at relatively small strains. A possible solution to this problem is a selective increase of steel sheet ductility by press hardening process design in areas where the component is required to deform plastically during crash tests. To this end, process designers require information about microstructure and mechanical properties as a function of the wide spectrum of cooling rates and sequences and austenitizing treatment conditions that can be encountered in production environments. In the present work, a Continuous Cooling Transformation (CCT) diagram with corresponding material properties of sheet steel 22MnB5 was determined for a wide spectrum of cooling rates. Heating and cooling programs were conducted in a quenching dilatometer. Motivated by the importance of residual elasticity in crash test performance, this property was measured using a micro-bending test and the results were integrated into the CCT diagrams to complement the hardness testing results. This information is essential for the process design of press hardening of sheet components with gradient material properties.

The "Reading the Mind in the Eyes" Test: Investigation of Psychometric Properties and Test-Retest Reliability of the Persian Version

Science.gov (United States)

Khorashad, Behzad S.; Baron-Cohen, Simon; Roshan, Ghasem M.; Kazemian, Mojtaba; Khazai, Ladan; Aghili, Zahra; Talaei, Ali; Afkhamizadeh, Mozhgan

2015-01-01

The psychometric properties of the Persian "Reading the Mind in the Eyes" test were investigated, so were the predictions from the Empathizing-Systemizing theory of psychological sex differences. Adults aged 16-69 years old (N = 545, female = 51.7%) completed the test online. The analysis of items showed them to be generally acceptable.…

Mixture toxicity of wood preservative products in the fish embryo toxicity test.

Science.gov (United States)

Coors, Anja; Dobrick, Jan; Möder, Monika; Kehrer, Anja

2012-06-01

Wood preservative products are used globally to protect wood from fungal decay and insects. We investigated the aquatic toxicity of five commercial wood preservative products, the biocidal active substances and some formulation additives contained therein, as well as six generic binary mixtures of the active substances in the fish embryo toxicity test (FET). Median lethal concentrations (LC50) of the single substances, the mixtures, and the products were estimated from concentration-response curves and corrected for concentrations measured in the test medium. The comparison of the experimentally observed mixture toxicity with the toxicity predicted by the concept of concentration addition (CA) showed less than twofold deviation for all binary mixtures of the active substances and for three of the biocidal products. A more than 60-fold underestimation of the toxicity of the fourth product by the CA prediction was detected and could be explained fully by the toxicity of one formulation additive, which had been labeled as a hazardous substance. The reason for the 4.6-fold underestimation of toxicity of the fifth product could not be explained unambiguously. Overall, the FET was found to be a suitable screening tool to verify whether the toxicity of formulated wood preservatives can reliably be predicted by CA. Applied as a quick and simple nonanimal screening test, the FET may support approaches of applying component-based mixture toxicity predictions within the environmental risk assessment of biocidal products, which is required according to European regulations. Copyright © 2012 SETAC.

DPRK's 4{sup th} Nuclear Test and its Tritium Production

Energy Technology Data Exchange (ETDEWEB)

Kim, Min Soo; Lee, Sang Joon; Chang, Sun Young [Korea Institute of Nuclear Nonproliferation and Control, Daejeon (Korea, Republic of)

2016-05-15

On January 6, 2016 at 10:30am, the artificial earthquake in the DPRK was detected by multiple international seismic organizations. After 2 hours, the DPRK announced on state TV that 'The first H-bomb test was successfully conducted in the DPRK at 10:00 am on Wednesday, Juche 105(2016), pursuant to the strategic determination of the ruling communist party.' There has been a doubt about the real nature of the DPRK's 4th nuclear test, since 2 months have been passed after its nuclear test. To analyze the nature of the DPRK's nuclear test, it is necessary to check possible options for production of essential materials. The pathways to produce nuclear fusion material (tritium) and to have a relatively high possibility for the DPRK are described in this article. Tritium is key material for H-bomb. And there are two options for the DPRK which are 1) production and 2) illicit trafficking. And this study is focused on production possibility of DPRK. Determination of the nature of DPRK's nuclear test is very hard issue.

Hanford Immobilized LAW Product Acceptance: Tanks Focus Area Testing Data Package II

International Nuclear Information System (INIS)

Schulz, Rebecca L.; Lorier, Troy H.; Peeler, David K.; Brown, Kevin G.; Reamer, Irene A.; Vienna, John D.; Jiricka, Antonin; Jorgensen, Benaiah M.; Smith, Donald E.

2001-01-01

This report is a continuation of the Hanford Immobilized Low Activity Waste (LAW) Product Acceptance (HLP): Initial Tanks Focus Area Testing Data Package (Vienna (and others) 2000). In addition to new 5000-h product consistency test (PCT), vapor hydration test (VHT), and alteration products data, some previously reported data together with relevant background information are included for an easily accessible source of reference when comparing the response of the various glasses to different test conditions. A matrix of 55 glasses was developed and tested to identify the impact of glass composition on long-term corrosion behavior and to develop an acceptable composition region for Hanford LAW glasses. Of the 55 glasses, 45 were designed to systematically vary the glass composition, and 10 were selected because large and growing databases on their corrosion characteristics had accumulated. The targeted and measured compositions of these glasses are found in the Appendix A. All glasses were fabricated according to standard procedures and heat treated to simulate the slow cooling that will occur in a portion of the waste glass after vitrification in the planned treatment facility at Hanford

Fertilizing properties of farm manure submitted to methane fermentation, according to pot tests

Energy Technology Data Exchange (ETDEWEB)

Kuzelewski, L; Pentkowski, A

1962-01-01

In order to compare the fertilizing properties of the ordinary farm manure stored and fermented in dung hills with those of the manure submitted to CH/sub 4/ fermentation, pot tests with oats and potatoes were carried out. Investigation showed that: N losses taking place during CH/sub 4/ fermentation are much smaller than those from manure fermented in dung-hills. Because of different fermentation processes, the losses of solid matter in the CH/sub 4/ fermentation were greater than in manure fermented and stored in dung-hills. Although the manure submitted to CH/sub 4/ fermentation contained more N, its effect on crops was almost identical with the effect of ordinary manure. Experiments have shown that it is not necessary to cover with soil the manure submitted to the CH/sub 4/ fermentation after spreading it. Whether it was covered with soil or not, there was no difference in crop yield. Manure fermenting in O-free atmosphere may contain products harmful to plants, but they oxidize quickly on exposure to the atmosphere. 53 references.

Impact of growth temperature on exopolysaccharide production and probiotic properties of Lactobacillus paracasei strains isolated from kefir grains.

Science.gov (United States)

Bengoa, Ana A; Llamas, M Goretti; Iraporda, Carolina; Dueñas, M Teresa; Abraham, Analía G; Garrote, Graciela L

2018-02-01

EPS-producing LAB are widely used in the dairy industry since these polymers improve the viscosity and texture of the products. Besides, EPS might be responsible for several health benefits attributed to probiotic strains. However, growth conditions (culture media, temperature, pH) could modify EPS production affecting both technological and probiotic properties. In this work, the influence of growth temperature on EPS production was evaluated, as well as the consequences of these changes in the probiotic properties of the strains. All Lactobacillus paracasei strains used in the study showed changes in EPS production caused by growth temperature, evidenced by the appearance of a high molecular weight fraction and an increment in the total amount of produced EPS at lower temperature. Nevertheless, these changes do not affect the probiotic properties of the strains; L. paracasei strains grown at 20 °C, 30 °C and 37 °C were able to survive in simulated gastrointestinal conditions, to adhere to Caco-2 cells after that treatment and to modulate the epithelial innate immune response. The results suggest that selected L. paracasei strains are new probiotic candidates that can be used in a wide range of functional foods in which temperature could be used as a tool to improve the technological properties of the product. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effect of silver (Ag) addition to mechanical and electrical properties of copper alloy (Cu) casting product

Science.gov (United States)

Felicia, Dian M.; Rochiem, R.; Laia, Standley M.

2018-04-01

Copper have good mechanical properties and good electrical conductivities. Therefore, copper usually used as electrical components. Silver have better electrical conductivities than copper. Female contact resistor is one of the electrical component used in circuit breaker. This study aims to analyze the effect of silver addition to hardness, strength, and electric conductivity properties of copper alloy. This study uses variation of 0; 0.035; 0.07; 0.1 wt. % Ag (silver) addition to determine the effect on mechanical properties and electrical properties of copper alloy through sand casting process. Modelling of thermal analysis and structural analysis was calculated to find the best design for the sand casting experiments. The result of Cu-Ag alloy as cast will be characterized by OES test, metallography test, Brinell hardness test, tensile test, and LCR meter test. The result of this study showed that the addition of silver increase mechanical properties of Cu-Ag. The maximum hardness value of this alloy is 83.1 HRB which is Cu-0.01 Ag and the lowest is 52.26 HRB which is pure Cu. The maximum strength value is 153.2 MPa which is Cu-0.07 Ag and the lowest is 94.6 MPa which is pure Cu. Silver addition decrease electrical properties of this alloy. The highest electric conductivity is 438.98 S/m which is pure Cu and the lowest is 52.61 S.m which is Cu-0.1 Ag.

Material property characterization of co-products from biofuel industries: Potential uses in value-added biocomposites

International Nuclear Information System (INIS)

Diebel, William; Reddy, Murali M.; Misra, Manju; Mohanty, Amar

2012-01-01

This paper gives an insight of biofuel production and the status -into the co-products obtained from this industry. Furthermore this work explores the possibility of these co-products as raw materials for value-added uses in material applications. This is achieved by understanding composition, solid density, and moisture content of prominent co-products such as soy meal, DDGS (distillers’ dried grains with solubles) and jatropha meal. Moisture content and density measurements showed no trend. Soy meal has the highest protein content, followed by jatropha and DDGS. Thermal stability of these co-products was analyzed by thermogravimetric analysis (TGA), which revealed that the thermal stabilities are ranked as soy meal>DDGS>jatropha meal. FT-IR spectroscopy was used to understand the functional groups in these meals and it showed that the amide group was prominent in all of these meals. In pursuit of finding value-added uses for these co-products of biofuel industries, biodegradable polymer, i.e. polycaprolactone (PCL), based biocomposites were prepared by melt processing technique using extrusion followed by injection molding. Tensile, flexural and impact properties were evaluated. Also, scanning electron microscopy (SEM) of fractured sections of the biocomposites was examined. -- Highlights: ► This paper gives an insight of biofuel production and its co-products. ► We have characterized biofuel co-products such as soy meal, DDGS and jatropha meal. ► Thermal stability and functional groups of these co-products were determined. ► Polycaprolactone based biocomposites were prepared by melt processing technique. ► Tensile, flexural and impact properties of these biocomposites were evaluated.

Uncovering Bugs in Distributed Storage Systems during Testing (not in Production!)

OpenAIRE

Deligiannis, P; McCutchen, M; Thomson, P; Chen, S; Donaldson, AF; Erickson, J; Huang, C; Lal, A; Mudduluru, R; Qadeer, S; Schulte, W

2016-01-01

Testing distributed systems is challenging due to multiple sources of nondeterminism. Conventional testing techniques, such as unit, integration and stress testing, are ineffective in preventing serious but subtle bugs from reaching production. Formal techniques, such as TLA+, can only verify high-level specifications of systems at the level of logic-based models, and fall short of checking the actual executable code. In this paper, we present a new methodology for testing distributed systems...

76 FR 9028 - Guidance for Industry: Potency Tests for Cellular and Gene Therapy Products; Availability

Science.gov (United States)

2011-02-16

...] Guidance for Industry: Potency Tests for Cellular and Gene Therapy Products; Availability AGENCY: Food and... Therapy Products'' dated January 2011. The guidance document provides manufacturers of cellular and gene... for Industry: Potency Tests for Cellular and Gene Therapy Products'' dated January 2011. The guidance...

77 FR 28673 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Furnace Fans

Science.gov (United States)

2012-05-15

... multipliers based on climate, consumer behavior assumptions, and product characteristics (e.g., multi-stage or... Conservation Program for Consumer Products: Test Procedures for Residential Furnace Fans; Proposed Rule #0;#0... Conservation Program for Consumer Products: Test Procedures for Residential Furnace Fans AGENCY: Office of...

77 FR 74559 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Water Heaters...

Science.gov (United States)

2012-12-17

... Conservation Program for Consumer Products: Test Procedures for Residential Water Heaters, Direct Heating... Energy (DOE) is amending its test procedures for residential water heaters, direct heating equipment (DHE... necessary for residential water heaters, because the existing test procedures for those products already...

Leaching characteristics of the metal waste form from the electrometallurgical treatment process: Product consistency testing

International Nuclear Information System (INIS)

Johnson, S. G.; Keiser, D. D.; Frank, S. M.; DiSanto, T.; Noy, M.

1999-01-01

Argonne National Laboratory is developing an electrometallurgical treatment for spent fuel from the experimental breeder reactor II. A product of this treatment process is a metal waste form that incorporates the stainless steel cladding hulls, zirconium from the fuel and the fission products that are noble to the process, i.e., Tc, Ru, Nb, Pd, Rh, Ag. The nominal composition of this waste form is stainless steel/15 wt% zirconium/1--4 wt% noble metal fission products/1--2 wt % U. Leaching results are presented from several tests and sample types: (1) 2 week monolithic immersion tests on actual metal waste forms produced from irradiated cladding hulls, (2) long term (>2 years) pulsed flow tests on samples containing technetium and uranium and (3) crushed sample immersion tests on cold simulated metal waste form samples. The test results will be compared and their relevance for waste form product consistency testing discussed

Measurement of the mechanical properties of layered systems

International Nuclear Information System (INIS)

Blank, E.

2002-01-01

Thin films for integrated electronic circuitry, packaging and small structures in micro-electromechanical systems (MEMS) as well as protective coatings require mechanical testing to control fabrication processes, guarantee product quality and establish data bases for engineering purposes. They generally escape classical materials testing owing to their small size in at least one dimension and their incorporation into larger structures. The fact that material properties change in the micro- and nanometer range when sample dimensions reach the scale of defect structures, implies that sample and probe size become part of the property evaluation process. Although research into the mechanical behaviour of thin films and small structures now is established, the fundamentals of mechanical testing continue to be identified while there is a growing need for methods allowing to measure intrinsic material properties. This lecture will focus on the mechanics of thin film and small volume structures and review recently developed testing techniques for measuring materials properties, particularly indentation, bulge and bend testing. The effect of specimen and probe geometry on property evaluation will be discussed. The use of Raman spectroscopy for residual stress measurement will be illustrated. (Author)

76 FR 22608 - Third Party Testing for Certain Children's Products; Clothing Textiles: Revisions to Terms of...

Science.gov (United States)

2011-04-22

... Product Certifications Based on Third Party Conformity Assessment Body Testing Prior to Commission's... the product. The Commission also emphasizes that, irrespective of certification, the product in... lifting the stay of enforcement with regard to testing and certification of children's products under 16...

Test marketing and consumer acceptance of irradiated meat products

International Nuclear Information System (INIS)

Xu Zhicheng; Feng Zhixiong; Jiang Peizhen

2001-01-01

This study consists of two parts: irradiation processing of cooked meat and irradiation preservation of prepackaged chilled fresh cut meats. Irradiation of prepackaged pickled meat products dipped in grains stillage at a dose 6-8 kGy eliminated common food-borne microorganisms, such as E. Coli and other microbial pathogens and extended the shelf life of the product to 10 days at 5 deg. C. Test marketing of 40,000 bags (about 10,000 kg) of the product in more than 100 supermarkets in the city of Shanghai showed no untoward problem with consumer acceptance. Irradiation of prepackaged chilled fresh cut pork at a dose 3 kGy led to inactivation of microbial pathogens and parasites with a concomitant reduction in numbers of common spoilage microorganisms and extension of shelf life of the product for 30 days at 5 deg. C. The cost benefit and marketing applications were evaluated. (author)

Yeast-Leavened Laminated Salty Baked Goods: Flour and Dough Properties and Their Relationship with Product Technological Quality.

Science.gov (United States)

de la Horra, Ana E; Steffolani, María Eugenia; Barrera, Gabriela N; Ribotta, Pablo D; León, Alberto E

2015-12-01

The effect of protein composition and content on the characteristics and properties of laminated baked products has been studied for a long time. However, there are no flour quality parameters related to its suitability to produce yeast-leavened laminated salty baked products. The relationships among flour characteristics, laminated dough pieces and baked products were studied in order to establish flour quality parameters and help predict the quality of the products. Yeast-leavened salty laminated products made with hard wheat flour had better quality properties than the products made with soft wheat flour. Hydrophilic components and a high gluten network quality are responsible for the generation of a rigid structure and viscous dough. Consequently, during baking, the dough rises rather than extends laterally and does not experience any change in the expected shape. Among the analysed flour characteristics, glutenin macropolymer content, lactic acid and sodium carbonate solvent retention capacities together with dough viscosity and resistance to deformation were the variables which influenced the most the quality of yeast-leavened salty laminated products.

Yeast-Leavened Laminated Salty Baked Goods: Flour and Dough Properties and Their Relationship with Product Technological Quality

Directory of Open Access Journals (Sweden)

Alberto E. León

2015-01-01

Full Text Available The effect of protein composition and content on the characteristics and properties of laminated baked products has been studied for a long time. However, there are no flour quality parameters related to its suitability to produce yeast-leavened laminated salty baked products. The relationships among flour characteristics, laminated dough pieces and baked products were studied in order to establish flour quality parameters and help predict the quality of the products. Yeast-leavened salty laminated products made with hard wheat flour had better quality properties than the products made with soft wheat flour. Hydrophilic components and a high gluten network quality are responsible for the generation of a rigid structure and viscous dough. Consequently, during baking, the dough rises rather than extends laterally and does not experience any change in the expected shape. Among the analysed flour characteristics, glutenin macropolymer content, lactic acid and sodium carbonate solvent retention capacities together with dough viscosity and resistance to deformation were the variables which influenced the most the quality of yeast-leavened salty laminated products.

Overview of the 2006-2008 JOGMEC/NRCan/Aurora Mallik Gas Hydrate Production Test Program

Science.gov (United States)

Yamamoto, K.; Dallimore, S. R.

2008-12-01

During the winters of 2007 and 2008 the Japan Oil, Gas and Metals National Corporation (JOGMEC) and Natural Resources Canada (NRCan), with Aurora Research Institute as the operator, carried out an on-shore gas hydrate production test program at the Mallik site, Mackenzie Delta, Northwest Territories, Canada. The prime objective of the program was to verify the feasibility of depressurization technique by drawing down the formation pressure across a 12m perforated gas hydrate bearing section. This project was the second full scale production test at this site following the 2002 Japex/JNOC/GSC et al Mallik research program in which seven participants organizatinos from five countries undertook a thermal test using hot water circulation Field work in 2007 was devoted to establishing a production test well, installing monitoring devices outside of casing, conducting base line geophysical studies and undertaking a short test to gain practical experience prior to longer term testing planned for 2008 . Hydrate-dissociated gas was produced to surface by depressurization achieved by lowering the fluid level with a dowhole pump. However, the operation was terminated 60 hours after the start of the pumping mainly due to sand production problems. In spite of the short period (12.5 hours of ellapsed pumping time), at least 830m3 of the gas was produced and accumulated in the borehole. Sand screens were installed across the perforated interval at the bottom hole for the 2008 program to overcome operational problems encountered in 2007 and achieve sustainable gas production. Stable bottom hole flowing pressures were successfully achieved during a 6 day test with continuous pump operation. Sustained gas production was achieved with rates between 2000- 4000m3/day and cummulative gas volume in the surface of approximately 13,000m3. Temperature and pressure data measured at the bottom hole and gas and water production rates gave positive evidence for the high efficiency of gas

Power Production Experience from Wave Dragon Prototype Testing in Nissum Bredning

DEFF Research Database (Denmark)

Frigaard, Peter; Kofoed, Jens Peter

The first Wave Dragon prototype power production testing started May 2003 and ended temporarily primo 2005. In the mentioned period Wave Dragon was situated in a corner of Nissum Bredning with relative little amount of wave energy. Main purpose of the tests was demonstration of survivability...

Endurance test on IR rig for RI production

International Nuclear Information System (INIS)

Chung, Heung June; Youn, Y. J.; Han, H. S.; Hong, S. B.; Cho, Y. G.; Ryu, J. S.

2000-12-01

This report presents the pressure drop, vibration and endurance test results for IR rig for RI production which were desigened and fabricated by KAERI. From the pressure drop test results, it is noted that the flow rate through the IR rig corresponding to the pressure drop of 200 kPa is measured to be about 3.12 kg/sec. Vibration frequency for the IR rig ranges from 13 to 17 Hz. RMS(Root Mean Square) displacement for the IR rig is less than 30 μm, and the maximum displacement is less than 110μm. These experimental results show that the design criteria of IR rig meet the HANARO limit conditions. Endurance test results show that the appreciable fretting wear for the IR rig does not occur, however tiny trace of wear between contact points is observed

Quality assurance and functionality tests on electrical components during the ATLAS IBL production

International Nuclear Information System (INIS)

Jentzsch, J

2013-01-01

To improve performance of the ATLAS inner tracker, a fourth Pixel layer, called the Insertable B-layer (IBL), will be installed in 2014 on a new beam pipe. A new read out chip generation, FE-I4, has been developed and two different sensor designs, a rather conventional planar and a 3D design, have been flip chipped to these front ends. New staves holding new stave and module flex circuits have been developed as well. Therefore, a production QA test bench has been established to test all production staves before integration with the new beam pipe. This setup combines former ATLAS Pixel services and a new readout system, namely the RCE (Reconfigurable Cluster Element) system developed at SLAC. With this setup all production staves will be tested to ensure the installation of only those staves which fulfill the IBL criteria. Quality assurance measurements under cleanroom conditions, including temperature and humidity control, are performed on the individual components during the various production steps of the IBL, namely connectivity as well as electrical tests and signal probing on individual parts and assembled subsystems. The pre-assembly QC procedures, the capabilities of the stave qualification setup, and recent results from testing a prototype stave are presented and discussed.

Quality assurance and functionality tests on electrical components during the ATLAS IBL production

Science.gov (United States)

Jentzsch, J.

2013-02-01

To improve performance of the ATLAS inner tracker, a fourth Pixel layer, called the Insertable B-layer (IBL), will be installed in 2014 on a new beam pipe. A new read out chip generation, FE-I4, has been developed and two different sensor designs, a rather conventional planar and a 3D design, have been flip chipped to these front ends. New staves holding new stave and module flex circuits have been developed as well. Therefore, a production QA test bench has been established to test all production staves before integration with the new beam pipe. This setup combines former ATLAS Pixel services and a new readout system, namely the RCE (Reconfigurable Cluster Element) system developed at SLAC. With this setup all production staves will be tested to ensure the installation of only those staves which fulfill the IBL criteria. Quality assurance measurements under cleanroom conditions, including temperature and humidity control, are performed on the individual components during the various production steps of the IBL, namely connectivity as well as electrical tests and signal probing on individual parts and assembled subsystems. The pre-assembly QC procedures, the capabilities of the stave qualification setup, and recent results from testing a prototype stave are presented and discussed.

Scaffold architecture and pharmacophoric properties of natural products and trade drugs: application in the design of natural product-based combinatorial libraries.

Science.gov (United States)

Lee, M L; Schneider, G

2001-01-01

Natural products were analyzed to determine whether they contain appealing novel scaffold architectures for potential use in combinatorial chemistry. Ring systems were extracted and clustered on the basis of structural similarity. Several such potential scaffolds for combinatorial chemistry were identified that are not present in current trade drugs. For one of these scaffolds a virtual combinatorial library was generated. Pharmacophoric properties of natural products, trade drugs, and the virtual combinatorial library were assessed using a self-organizing map. Obviously, current trade drugs and natural products have several topological pharmacophore patterns in common. These features can be systematically explored with selected combinatorial libraries based on a combination of natural product-derived and synthetic molecular building blocks.

Influence of green manure in physical and biological properties of soil and productivity in the culture of soybean

Directory of Open Access Journals (Sweden)

Ricardo Alves Cardoso

2014-12-01

Full Text Available Green manuring is the practice of using plant species in rotation, succession or intercropped with other crops, aiming improvement, maintenance and recovery of physical, chemical and biological soil properties. The objective was to evaluate the influence of different green manures on soil characteristics and productivity of soybean. The experiment was conducted in Maringá (PR in a randomized block design with six treatments and four replications: T1: oat (Avena Sativa, T2: black oat (Avena strigosa, T3: dwarf pigeon pea (Cajanus cajan, T4: radish (Raphanus sativus L., T5: white lupine (Lupinus albus and T6: control (fallow. At the end of the experiment, relations were established between the green manure used for soybean production, the production of biomass, the development of microorganisms and soil bulk density. The data were analyzed with statistical software and means were compared by Tukey test at 5% probability. The coverages provided higher content of dry matter were lupine, black oat and faba bean. Treatments that most influenced the increase of soil microorganisms were lupine, radish and pigeonpea. Regarding productivity, higher values were obtained in treatments with pigeon pea, lupine and oat. The apparent density of the soil, treatment with turnip showed better results.

Property Rights and Productivity

DEFF Research Database (Denmark)

Newman, Carol; Tarp, Finn; Van Den Broeck, Katleen

2015-01-01

This paper explores the effect of land titling on agricultural productivity in Vietnam and the productivity effects of single versus joint titling for husband and wife. Using a plot-fixed-effects approach our results show that obtaining a land title is associated with higher yields, for both...... individually and jointly held titles. We conclude that there is no tradeoff between joint titling and productivity, and so joint titles are potentially an effective way to improve women’s bargaining power within the household with no associated efficiency losses....

Furniture wood wastes: Experimental property characterisation and burning tests

International Nuclear Information System (INIS)

Tatano, Fabio; Barbadoro, Luca; Mangani, Giovanna; Pretelli, Silvia; Tombari, Lucia; Mangani, Filippo

2009-01-01

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected 'raw' and primarily 'engineered' ('composite') wood wastes. The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in 'engineered' wood wastes as compared with 'raw' wood wastes; and relatively high energy content values of 'engineered' wood wastes (ranging on the whole from 3675 to 5105 kcal kg -1 for HHV, and from 3304 to 4634 kcal kg -1 for LHV). The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in 'engineered' wood burning tests of pyrroles and amines, as well as the additional presence (as compared with 'raw' wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon. Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in 'engineered' wood burning tests as compared with 'raw' wood burning test; and considerable generation of the respirable PM 1 fraction during incomplete industrial wood burning.

Products by Glycation Process

Directory of Open Access Journals (Sweden)

Liliana Ortega

2015-01-01

Full Text Available The antioxidant properties of sweet and acid whey products were incremented by polymerization of their proteins by glycation of whey protein concentrates (WPC and their hydrolyzates (WPCH with ribose and glucose in individual experiments under similar concentration. Heating at 50°C during 20 h maximum and pH 7 and pH 9 were used in all tests. The higher activity was found in WPC glycosylates products with ribose at pH 7 and heating during 10–15 h. In comparable form, antioxidant activity in WPCH was incremented by prior hydrolysis to glycation with 25–45% of hydrolysis degree. Further functional properties of whey proteins (solubility, emulsion, and foam were also improved by the polymerization with ribose. The color of polymerized products due to Maillard reactions was associated with antioxidant activity of each compound; however comparative color in glycosylates products with glucose and ribose did not show this effect.

Thermophysical and Optical Properties of Materials Considered for Use on the LDSD Test Vehicle

Science.gov (United States)

Redmond, Matthew; Mastropietro, A.J.

2015-01-01

In June 2014, the first of multiple flights in the Low Density Supersonic Decelerator (LDSD) technology development program took place and successfully demonstrated a Supersonic Inflatable Aerodynamic Decelerator (SIAD) in Mars-like conditions. Although the primary goal of the technology program was the development of new decelerators for landing heavier payloads on Mars, the low-cost thermal design of the test vehicle was only possible through the innovative use of a combination of both commercial off the shelf (COTS) and aerospace grade materials. As a result, numerous thermophysical and optical property measurements were undertaken to characterize material candidates before the final material selection was made. This paper presents thermophysical and optical property measurements performed over the course of the LDSD test vehicle development, including those not ultimately selected for use on the vehicle. These properties are compared and contrasted with the existing measurements available in previous literature.

Testing and Validation of the Dynamic Inertia Measurement Method

Science.gov (United States)

Chin, Alexander W.; Herrera, Claudia Y.; Spivey, Natalie D.; Fladung, William A.; Cloutier, David

2015-01-01

The Dynamic Inertia Measurement (DIM) method uses a ground vibration test setup to determine the mass properties of an object using information from frequency response functions. Most conventional mass properties testing involves using spin tables or pendulum-based swing tests, which for large aerospace vehicles becomes increasingly difficult and time-consuming, and therefore expensive, to perform. The DIM method has been validated on small test articles but has not been successfully proven on large aerospace vehicles. In response, the National Aeronautics and Space Administration Armstrong Flight Research Center (Edwards, California) conducted mass properties testing on an "iron bird" test article that is comparable in mass and scale to a fighter-type aircraft. The simple two-I-beam design of the "iron bird" was selected to ensure accurate analytical mass properties. Traditional swing testing was also performed to compare the level of effort, amount of resources, and quality of data with the DIM method. The DIM test showed favorable results for the center of gravity and moments of inertia; however, the products of inertia showed disagreement with analytical predictions.

Quality Assurance and Functionality Tests on Electrical Components during the ATLAS IBL Production

CERN Document Server

Jentzsch, J

2013-01-01

To improve performance of the ATLAS inner tracker, a fourth Pixel layer, called the Insertable B-layer (IBL), will be installed in 2014 on a new beam pipe. A new read out chip generation, FE-I4, has been developed and two different sensor designs, a rather conventional planar and a 3D design, have been flip chipped to these front ends. New staves holding new stave and module flex circuits have been developed as well. Therefore, a production QA test bench has been established to test all production staves before integration with the new beam pipe. This setup combines former ATLAS Pixel services and a new readout system, namely the RCE (Reconfigurable Cluster Element) system developed at SLAC. With this setup all production staves will be tested to ensure the installation of only those staves which fulfill the IBL criteria. Quality assurance measurements under cleanroom conditions, including temperature and humidity control, are performed on the individual components during the various production steps of the I...

40 CFR 1051.301 - When must I test my production-line vehicles or engines?

Science.gov (United States)

2010-07-01

... vehicles or engines? 1051.301 Section 1051.301 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Testing Production-Line Vehicles and Engines § 1051.301 When must I test my production-line vehicles or engines? (a...

Improving Papanicolaou test quality and reducing medical errors by using Toyota production system methods.

Science.gov (United States)

Raab, Stephen S; Andrew-Jaja, Carey; Condel, Jennifer L; Dabbs, David J

2006-01-01

The objective of the study was to determine whether the Toyota production system process improves Papanicolaou test quality and patient safety. An 8-month nonconcurrent cohort study that included 464 case and 639 control women who had a Papanicolaou test was performed. Office workflow was redesigned using Toyota production system methods by introducing a 1-by-1 continuous flow process. We measured the frequency of Papanicolaou tests without a transformation zone component, follow-up and Bethesda System diagnostic frequency of atypical squamous cells of undetermined significance, and diagnostic error frequency. After the intervention, the percentage of Papanicolaou tests lacking a transformation zone component decreased from 9.9% to 4.7% (P = .001). The percentage of Papanicolaou tests with a diagnosis of atypical squamous cells of undetermined significance decreased from 7.8% to 3.9% (P = .007). The frequency of error per correlating cytologic-histologic specimen pair decreased from 9.52% to 7.84%. The introduction of the Toyota production system process resulted in improved Papanicolaou test quality.

Ignition and flame spread properties of wood, elaborated during a new test method based on convective heat flux

DEFF Research Database (Denmark)

Sørensen, Lars Schiøtt

Ignition and flame spread properties on selected types of wood and wall papers are elaborated. Tests are established in a new test setup in which the test specimen can be fixed in different angles due to a horizontal level. The heat exposing the test objects is arranged as a convective flux......, established from a Bunsen burners pilot flame. This principal is somewhat in contrast to the more typical radiation established fluxes. For instance, the ISO 9239 (DS 2000) test method is based on a gas fired radiant panel. And in the ISO 5657 standard, the ignition properties are investigated on test...

Biochar from different residues on soil properties and common bean production

Directory of Open Access Journals (Sweden)

Isley Cristiellem Bicalho da Silva

Full Text Available ABSTRACT: The production of biochar from organic residues promises to be an interesting strategy for the management of organic waste. To assess the effect of biochar on soil properties and the production and nutrition of common bean (Phaseolus vulgaris L., three simultaneous experiments were conducted in a greenhouse with different biochar from organic residues (rice husk, sawdust, and sorghum silage used as filtration material for swine biofertilizer. In each experiment the treatments consisted of five different biochar concentrations (0, 25, 50, 75 and 100 L m−3, arranged in a completely randomized design, with four repetitions. In the experiments, the use of biochar increased soil pH, cation exchange capacity, nutrient availability in the soil, and nutrient accumulation in grains. The biochar concentrations corresponding to the maximum production of grain dry matter of bean plants were 100, 68, and 71 L m−3 for biochar from rice husk filter (BRHF, biochar from sawdust filter (BSF, and biochar from sorghum silage filter (BSSF, respectively.

[Functional meat products; development and evaluation of their health-promoting properties].

Science.gov (United States)

Olmedilla-Alonso, Begoña; Jiménez-Colmenero, Francisco

2014-06-01

For a number of reasons, meat products are an exceptionally adequate means for introducing different bioactive compounds into the diet without modifying eating habits. In recent years, there has been a notable development of meat products designed as potentially functional foods. Within the framework of the functional food, this article provides a general view of the reasons that motivate and justify their formulation, with special emphasis on: a) aspects to be considered in their design in order to be able to make nutrition claims and statements concerning their health-promoting properties; b) the strategies employed to optimize the presence of functional ingredients, favoring the presence of beneficial bioactive compounds and limiting others with negative consequences for our health, and c) the procedures for demonstrating a relationship between the consumption of potentially functional meat products with beneficial effects on health and the way in which these studies are reflected in the literature. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

Microbial production of polyhydroxybutyrate with tailor-made properties: an integrated modelling approach and experimental validation.

Science.gov (United States)

Penloglou, Giannis; Chatzidoukas, Christos; Kiparissides, Costas

2012-01-01

The microbial production of polyhydroxybutyrate (PHB) is a complex process in which the final quantity and quality of the PHB depend on a large number of process operating variables. Consequently, the design and optimal dynamic operation of a microbial process for the efficient production of PHB with tailor-made molecular properties is an extremely interesting problem. The present study investigates how key process operating variables (i.e., nutritional and aeration conditions) affect the biomass production rate and the PHB accumulation in the cells and its associated molecular weight distribution. A combined metabolic/polymerization/macroscopic modelling approach, relating the process performance and product quality with the process variables, was developed and validated using an extensive series of experiments and measurements. The model predicts the dynamic evolution of the biomass growth, the polymer accumulation, the consumption of carbon and nitrogen sources and the average molecular weights of the PHB in a bioreactor, under batch and fed-batch operating conditions. The proposed integrated model was used for the model-based optimization of the production of PHB with tailor-made molecular properties in Azohydromonas lata bacteria. The process optimization led to a high intracellular PHB accumulation (up to 95% g of PHB per g of DCW) and the production of different grades (i.e., different molecular weight distributions) of PHB. Copyright © 2011 Elsevier Inc. All rights reserved.