Assessing the impacts of ethanol and isobutanol on gaseous and particulate emissions from flexible fuel vehicles.

Science.gov (United States)

Karavalakis, Georgios; Short, Daniel; Russell, Robert L; Jung, Heejung; Johnson, Kent C; Asa-Awuku, Akua; Durbin, Thomas D

2014-12-02

This study investigated the effects of higher ethanol blends and an isobutanol blend on the criteria emissions, fuel economy, gaseous toxic pollutants, and particulate emissions from two flexible-fuel vehicles equipped with spark ignition engines, with one wall-guided direct injection and one port fuel injection configuration. Both vehicles were tested over triplicate Federal Test Procedure (FTP) and Unified Cycles (UC) using a chassis dynamometer. Emissions of nonmethane hydrocarbons (NMHC) and carbon monoxide (CO) showed some statistically significant reductions with higher alcohol fuels, while total hydrocarbons (THC) and nitrogen oxides (NOx) did not show strong fuel effects. Acetaldehyde emissions exhibited sharp increases with higher ethanol blends for both vehicles, whereas butyraldehyde emissions showed higher emissions for the butanol blend relative to the ethanol blends at a statistically significant level. Particulate matter (PM) mass, number, and soot mass emissions showed strong reductions with increasing alcohol content in gasoline. Particulate emissions were found to be clearly influenced by certain fuel parameters including oxygen content, hydrogen content, and aromatics content.

Performance simulations of catalytic converters during the Federal Test Procedure

Energy Technology Data Exchange (ETDEWEB)

Shen, H.; Shamim, T.; Sengupta, S.; Son, S.; Adamczyk, A.A.

1999-07-01

A numerical study is carried out to predict the tailpipe emissions and emission conversion efficiencies of unburned hydrocarbon, nitrogen oxide and carbon monoxide flowing through a catalytic converter during the Federal Test Procedure (FTP). The model considers the effect of heat transfer in the catalytic converter, coupled with catalyst chemical kinetics, including an oxygen storage mechanism. The resulting governing equations based on the conservation of mass and energy are solved by a tridiagonal matrix algorithm (TDMA) with a successive line under relaxation method. The numerical scheme for this non-linear problem is found to have good convergence efficiency. The simulation for the complete FTP cycle is accomplished in less than fifteen minutes on a desktop personal computer. A 13-step reaction mechanism plus a nine-step O{sub 2} storage mechanism is used to simulate the chemical kinetics. The energy equations include the heat loss due to conduction and convection plus the energy liberated by chemical reactions. The effect of radiation is assumed to be negligible and is not considered. The results of the numerical model for both the instantaneous and accumulated emissions are found to be in good agreement with experimental measurements. The conversion efficiencies of HC, CO and NO as predicted by the model are found to be within 5% of those dynamic measurements, and calculated results of accumulated HC, CO and NO{sub x} are in fair agreement with experimental measurements. The transient measurements are also used to check the robustness of the numerical model. The model is found to be robust and hence can simulate various operating conditions of engine output to the converter.

Will Aerosol Hygroscopicity Change with Biodiesel, Renewable Diesel Fuels and Emission Control Technologies?

Science.gov (United States)

Vu, Diep; Short, Daniel; Karavalakis, Georgios; Durbin, Thomas D; Asa-Awuku, Akua

2017-02-07

The use of biodiesel and renewable diesel fuels in compression ignition engines and aftertreatment technologies may affect vehicle exhaust emissions. In this study two 2012 light-duty vehicles equipped with direct injection diesel engines, diesel oxidation catalyst (DOC), diesel particulate filter (DPF), and selective catalytic reduction (SCR) were tested on a chassis dynamometer. One vehicle was tested over the Federal Test Procedure (FTP) cycle on seven biodiesel and renewable diesel fuel blends. Both vehicles were exercised over double Environmental Protection Agency (EPA) Highway fuel economy test (HWFET) cycles on ultralow sulfur diesel (ULSD) and a soy-based biodiesel blend to investigate the aerosol hygroscopicity during the regeneration of the DPF. Overall, the apparent hygroscopicity of emissions during nonregeneration events is consistently low (κ diesel vehicles. As such, the contribution of regeneration emissions from a growing fleet of diesel vehicles will be important.

Ammonia, nitrous oxide and hydrogen cyanide emissions from five passenger vehicles

International Nuclear Information System (INIS)

Karlsson, Hua Lu

2004-01-01

In this paper, three unregulated components, ammonia, nitrous oxide and hydrogen cyanide, emitted from five passenger vehicles are investigated. With focus upon emission factors from existing production technology, vehicles produced between 1989 and 1998 with considerable mileage (7000 to 280,000) are chosen. Among the five vehicles, four were sold in the European market, whereas one was sold in the US market. The vehicles are tested on a chassis dynamometer. An EU2000 Driving Cycle (NEDC) and a US Urban Driving Cycle (UDC) of the Federal Test Procedure 75 (FTP-75) are used in the study. The regulated emissions are measured using a Horiba Mexa series. Unregulated emissions, ammonia (NH 3 ), nitrous oxide (N 2 O) and hydrogen cyanide (HCN) are analysed by mass spectrometer, gas chromatography and CNT-NA, TIM315-74W method, respectively. Both the unregulated emissions and the regulated emissions show driving cycle dependency; and they are also improved with newer vehicle and emission control technology. However, a gasoline direct injection vehicle (relatively new technology in this study) has rather high regulated emissions, whereas the NH 3 , N 2 O and HCN emissions are low

Ammonia, nitrous oxide and hydrogen cyanide emissions from five passenger vehicles.

Science.gov (United States)

Karlsson, Hua Lu

2004-12-01

In this paper, three unregulated components, ammonia, nitrous oxide and hydrogen cyanide, emitted from five passenger vehicles are investigated. With focus upon emission factors from existing production technology, vehicles produced between 1989 and 1998 with considerable mileage (7000 to 280,000) are chosen. Among the five vehicles, four were sold in the European market, whereas one was sold in the US market. The vehicles are tested on a chassis dynamometer. An EU2000 Driving Cycle (NEDC) and a US Urban Driving Cycle (UDC) of the Federal Test Procedure 75 (FTP-75) are used in the study. The regulated emissions are measured using a Horiba Mexa series. Unregulated emissions, ammonia (NH(3)), nitrous oxide (N(2)O) and hydrogen cyanide (HCN) are analysed by mass spectrometer, gas chromatography and CNT-NA, TIM315-74W method, respectively. Both the unregulated emissions and the regulated emissions show driving cycle dependency; and they are also improved with newer vehicle and emission control technology. However, a gasoline direct injection vehicle (relatively new technology in this study) has rather high regulated emissions, whereas the NH(3), N(2)O and HCN emissions are low.

Development of real-world driving cycles and estimation of emission factors for in-use light-duty gasoline vehicles in urban areas.

Science.gov (United States)

Hwa, Mei-Yin; Yu, Tai-Yi

2014-07-01

This investigation adopts vehicle tracking manner to establish real-world driving patterns and estimates emission factors with dynamometers with 23 traffic-driving variables for 384 in-use light-duty passenger vehicles during non-rush hour. Adequate numbers of driving variables were decided with factor analysis and cluster analysis. The dynamometer tests were performed on FTP75 cycle and five local driving cycles derived from real-world speed profiles. Results presented that local driving cycles and FTP75 cycle were completely different in driving characteristic parameters of typical driving cycles and emission factors. The highest values of emission factor ratios of local driving cycle and FTP75 cycle for CO, NMHC, NO x , CH4, and CO2 were 1.38, 1.65, 1.58, 1.39, and 1.14, respectively.

RANCANG BANGUN FILE TRANSFER PROTOCOL (FTP DENGAN PENGAMANAN OPEN SSL PADA JARINGAN VPN MIKROTIK DI SMK DWIWARNA

Directory of Open Access Journals (Sweden)

Devi Ruwaida

2018-01-01

Full Text Available File Transfer Protocol (FTP server merupakan jenis sistem yang menghubungkan hak pengakses (client dan penyedia (server dalam melakukan pertukaran data yang melewati port 21, yang semula ftp server berjalan pada protocol yang tidak terlindungi di dalam port 21, kemudian dengan OpenSSL ini di amankan agar data dapat sampai ke tujuan. Pada penelitian ini akan dibangun Rancang Bangun File Transfer Protocol (Ftp Dengan Pengamanan Open Ssl Pada Jaringan Vpn Mikrotik Di Smk Dwiwarna  yang akan di konfigurasi pada debian 9.1 dengan  di tambahnya pengaman sertifikat ssl , dengan harapan  melindungi proses dalam pengiriman data dapat dengan aman dan ditambahkannya sistem VPN PPTP pada mikrotik akan lebih memberikan keamanan yang lebih baik lagi, dimana pemanfaatan Point-to-Point Tunneling Protocol (PPTP suatu protokol jaringan yang bisa memungkinkan client dalam pengiriman data secara aman melalui remote client kepada server sekolah dibangunnya suatu virtual private network (VPN.

40 CFR 93.118 - Criteria and procedures: Motor vehicle emissions budget.

Science.gov (United States)

2010-07-01

... emissions budget. 93.118 Section 93.118 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... and procedures: Motor vehicle emissions budget. (a) The transportation plan, TIP, and project not from a conforming transportation plan and TIP must be consistent with the motor vehicle emissions budget...

Using Globus GridFTP to Transfer and Share Big Data | Poster

Science.gov (United States)

By Ashley DeVine, Staff Writer, and Mark Wance, Guest Writer; photo by Richard Frederickson, Staff Photographer Transferring big data, such as the genomics data delivered to customers from the Center for Cancer Research Sequencing Facility (CCR SF), has been difficult in the past because the transfer systems have not kept pace with the size of the data. However, the situation is changing as a result of the Globus GridFTP project.

Emissions from Road Vehicles Fuelled by Fischer Tropsch Based Diesel and Gasoline

Energy Technology Data Exchange (ETDEWEB)

Larsen, U; Lundorf, P; Ivarsson, A; Schramm, J [Technical University of Denmark (Denmark); Rehnlund, B [Atrax Energi AB (Sweden); Blinge, M [The Swedish Transport Institute (Sweden)

2006-11-15

The described results were carried out under the umbrella of IEA Advanced Motor Fuels Agreement. The purpose was to evaluate the emissions of carbon monoxide (CO), unburned hydrocarbons (HC), nitrogen oxides (NOx), particulate matter (PM) and polycyclic aromatic hydrocarbons (PAH) from vehicles fuelled by Fischer Tropsch (FT) based diesel and gasoline fuel, compared to the emissions from ordinary diesel and gasoline. The comparison for diesel fuels was based on a literature review, whereas the gasoline comparison had to be based on our own experiments, since almost no references were found in this field. In this context measurement according to the Federal Test Procedure (FTP) and the New European Driving Cycle (NEDC) were carried out on a chassis dynamometer with a directly injected gasoline vehicle. Experiments were carried out with a reference fuel, a fuel based 70% on FT and an alkylate fuel (Aspen), which was supposed to be very similar, in many ways, to FT fuel. FT based diesel generally showed good emission performance, whereas the FT based gasoline not necessary lead to lower emissions. On the other hand, the Aspen fuel did show many advantages for the emissions from the gasoline vehicle.

Emissions from Diesel and Gasoline Vehicles Fuelled by Fischer-Tropsch Fuels and Similar Fuels

DEFF Research Database (Denmark)

Larsen, Ulrik; Lundorff, Peter; Ivarsson, Anders

2007-01-01

The described investigation was carried out under the umbrella of IEA Advanced Motor Fuels Agreement. The purpose was to evaluate the emissions of carbon monoxide (CO), unburned hydrocarbons (HC), nitrogen oxides (NOx), particulate matter (PM) and polycyclic aromatic hydrocarbons (PAH) from...... vehicles fuelled by Fischer Tropsch (FT) based diesel and gasoline fuel, compared to the emissions from ordinary diesel and gasoline. The comparison for diesel fuels was based on a literature review, whereas the gasoline comparison had to be based on our own experiments, since almost no references were...... found in this field. In this context measurement according to the Federal Test Procedure (FTP) and the New European Driving Cycle (NEDC) were carried out on a chassis dynamometer with a directly injected gasoline vehicle. Experiments were carried out with a reference fuel, a fuel based 70% on FT...

40 CFR 205.54-1 - Low speed sound emission test procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Low speed sound emission test procedures. 205.54-1 Section 205.54-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Medium and Heavy Trucks § 205...

Optimization of Fuel Consumption and Emissions for Auxiliary Power Unit Based on Multi-Objective Optimization Model

Directory of Open Access Journals (Sweden)

Yongpeng Shen

2016-02-01

Full Text Available Auxiliary power units (APUs are widely used for electric power generation in various types of electric vehicles, improvements in fuel economy and emissions of these vehicles directly depend on the operating point of the APUs. In order to balance the conflicting goals of fuel consumption and emissions reduction in the process of operating point choice, the APU operating point optimization problem is formulated as a constrained multi-objective optimization problem (CMOP firstly. The four competing objectives of this CMOP are fuel-electricity conversion cost, hydrocarbon (HC emissions, carbon monoxide (CO emissions and nitric oxide (NO x emissions. Then, the multi-objective particle swarm optimization (MOPSO algorithm and weighted metric decision making method are employed to solve the APU operating point multi-objective optimization model. Finally, bench experiments under New European driving cycle (NEDC, Federal test procedure (FTP and high way fuel economy test (HWFET driving cycles show that, compared with the results of the traditional fuel consumption single-objective optimization approach, the proposed multi-objective optimization approach shows significant improvements in emissions performance, at the expense of a slight drop in fuel efficiency.

The Impact of FTP on Commitment to Career Choices: Situating within a Social Cognitive Perspective

Science.gov (United States)

Phan, Huy P.

2015-01-01

Future time perspective (FTP) is an important theoretical construct that may assist educators in their understanding of individuals' learning, motivation and decision-making. There is empirical evidence attesting to the predictive effects of anticipation of future goals on both cognitive and non-cognitive outcomes. The present study, based on…

Telejornalismo na Amaz?nia: o FTP como instrumento de integra??o regional

OpenAIRE

Batista, Lu?s Augusto Pires

2010-01-01

Esta disserta??o investiga o efeito do sistema FTP (File Transfer Protocol ou Protocolo de Transfer?ncia de Arquivo) no processo de produ??o do telejornalismo das emissoras da Rede Amaz?nica (TV Amazonas, TV Rond?nia, TV Acre, TV Roraima e TV Amap?), a partir da Central de Jornalismo sediada na capital do estado no Amazonas e seus efeitos no cotidiano da comunidade do munic?pio de Manacapuru, que passou a ser n?o apenas consumidora de informa??o, mas tamb?m produtora dela. C...

Effect of upgraded diesel fuels and oxidation catalysts on emission properties, especially PAH and genotoxicity

DEFF Research Database (Denmark)

Johansen, Keld; Gabrielsson, Pär; Stavnsbjerg, Peter

1997-01-01

in an engine test bench and a full ECE R49 13 mode test was performed and 2) a VW GOLF 1.6 l engine was mounted in a car and a full transient FTP-75 test was performed. Regulated emissions and unregulated emissions as SOF, sulphur, nitrate, PAH in PM plus vapour phase were measured. Genotoxic activity...

Caracterização das emissões de aldeídos de veículos do ciclo diesel Emission of aldehydes from light duty diesel vehicles

Directory of Open Access Journals (Sweden)

Rui de Abrantes

2005-06-01

Full Text Available OBJETIVO: Caracterizar as emissões de acetaldeído e formaldeído, substâncias nocivas para a saúde das pessoas e cujas emissões dos veículos a diesel ainda não estão regulamentadas. MÉTODOS: Testes padronizados foram realizados em quatro veículos leves comerciais do ciclo diesel, testados num dinamômetro de chassis, usando o procedimento de teste FTP-75. Os poluentes foram analisados por cromatografia líquida de alta eficiência. RESULTADOS: Os resultados mostraram que a emissão de acetaldeído variou de 5,9 a 45,4 mg/km e a de formaldeído variou de 16,5 a 115,2 mg/km. A emissão média para a soma dos aldeídos foi de 58,7 mg/km, variando de 22,5 mg/km a 160 mg/km. A proporção entre os dois se manteve constante, próximo de 74% de formaldeído e 26% de acetaldeído. CONCLUSÕES: A emissão de aldeídos provenientes de veículos movidos a diesel foi significativa quando comparada com as emissões reais dos veículos de ignição por centelha ou com o limite previsto para os veículos do ciclo Otto na legislação brasileira. O estabelecimento de limites de emissão para essas substâncias para veículos a diesel mostra-se importante, considerando o crescimento da frota de veículos a diesel, a toxicidade desses compostos e sua participação como precursores nas reações de formação de gás ozônio na baixa troposfera.OBJECTIVE: To characterize acetaldehyde and formaldehyde emissions, which are harmful gases to human health and not yet regulated for diesel engines. METHODS: Standardized tests were performed in four diesel light duty commercial vehicles, using a frame dynamometer and test procedure FTP-75. The pollutants were analyzed by high performance liquid chromatography. RESULTS: Results have shown acetaldehyde emission ranged from 5.9 to 45.4 mg/km, and formaldehyde emission from 16.5 to 115.2 mg/km. The average emission for aldehyde sum was 58.7 mg/km, ranging from 22.4 to 160.6 mg/km. The proportion between the two

40 CFR 86.1825-08 - Durability demonstration procedures for refueling emissions.

Science.gov (United States)

2010-07-01

..., statistical analyses, additional data, or other information which is relevant to the decision. The... Durability demonstration procedures for refueling emissions. This section applies to 2008 and later model...-duty rules as allowed under the provisions of § 86.1801-01(c)(1) which are subject to refueling loss...

Test/QA plan for the verification testing of alternative or reformulated liquid fuels, fuel additives, fuel emulsions, and lubricants for highway and nonroad use heavy-duty diesel engines

Science.gov (United States)

This Environmental Technology Verification Program test/QA plan for heavy-duty diesel engine testing at the Southwest Research Institute’s Department of Emissions Research describes how the Federal Test Procedure (FTP), as listed in 40 CFR Part 86 for highway engines and 40 CFR P...

Fourier transform profilometry (FTP) using an innovative band-pass filter for accurate 3-D surface reconstruction

Science.gov (United States)

Chen, Liang-Chia; Ho, Hsuan-Wei; Nguyen, Xuan-Loc

2010-02-01

This article presents a novel band-pass filter for Fourier transform profilometry (FTP) for accurate 3-D surface reconstruction. FTP can be employed to obtain 3-D surface profiles by one-shot images to achieve high-speed measurement. However, its measurement accuracy has been significantly influenced by the spectrum filtering process required to extract the phase information representing various surface heights. Using the commonly applied 2-D Hanning filter, the measurement errors could be up to 5-10% of the overall measuring height and it is unacceptable to various industrial application. To resolve this issue, the article proposes an elliptical band-pass filter for extracting the spectral region possessing essential phase information for reconstructing accurate 3-D surface profiles. The elliptical band-pass filter was developed and optimized to reconstruct 3-D surface models with improved measurement accuracy. Some experimental results verify that the accuracy can be effectively enhanced by using the elliptical filter. The accuracy improvement of 44.1% and 30.4% can be achieved in 3-D and sphericity measurement, respectively, when the elliptical filter replaces the traditional filter as the band-pass filtering method. Employing the developed method, the maximum measured error can be kept within 3.3% of the overall measuring range.

Test/QA plan for the verification testing of diesel exhaust catalysts, particulate filters and engine modification control technologies for highway and nonroad use diesel engines

Science.gov (United States)

This ETV test/QA plan for heavy-duty diesel engine testing at the Southwest Research Institute’s Department of Emissions Research (DER) describes how the Federal Test Procedure (FTP), as listed in 40 CFR Part 86 for highway engines and 40 CFR Part 89 for nonroad engines, will be ...

Test/QA plan for the verification testing of selective catalytic reduction control technologies for highway, nonroad use heavy-duty diesel engines

Science.gov (United States)

This ETV test/QA plan for heavy-duty diesel engine testing at the Southwest Research Institute’s Department of Emissions Research (DER) describes how the Federal Test Procedure (FTP), as listed in 40 CFR Part 86 for highway engines and 40 CFR Part 89 for nonroad engines, will be ...

European type-approval test procedure for evaporative emissions from passenger cars against real-world mobility data from two Italian provinces.

Science.gov (United States)

Martini, Giorgio; Paffumi, Elena; De Gennaro, Michele; Mellios, Giorgos

2014-07-15

This paper presents an evaluation of the European type-approval test procedure for evaporative emissions from passenger cars based on real-world mobility data. The study relies on two large databases of driving patterns from conventional fuel vehicles collected by means of on-board GPS systems in the Italian provinces of Modena and Firenze. Approximately 28,000 vehicles were monitored, corresponding to approximately 36 million kilometres over a period of one month. The driving pattern of each vehicle was processed to derive the relation between trip length and parking duration, and the rate of occurrence of parking events against multiple evaporative cycles, defined on the basis of the type-approval test procedure as 12-hour diurnal time windows. These results are used as input for an emission simulation model, which calculates the total evaporative emissions given the characteristics of the evaporative emission control system of the vehicle and the ambient temperature conditions. The results suggest that the evaporative emission control system, fitted to the vehicles from Euro 3 step and optimised for the current type-approval test procedure, could not efficiently work under real-world conditions, resulting in evaporative emissions well above the type-approval limit, especially for small size vehicles and warm climate conditions. This calls for a revision of the type-approval test procedure in order to address real-world evaporative emissions. Copyright © 2014. Published by Elsevier B.V.

Idle emissions from heavy-duty diesel and natural gas vehicles at high altitude.

Science.gov (United States)

McCormick, R L; Graboski, M S; Alleman, T L; Yanowitz, J

2000-11-01

Idle emissions of total hydrocarbon (THC), CO, NOx, and particulate matter (PM) were measured from 24 heavy-duty diesel-fueled (12 trucks and 12 buses) and 4 heavy-duty compressed natural gas (CNG)-fueled vehicles. The volatile organic fraction (VOF) of PM and aldehyde emissions were also measured for many of the diesel vehicles. Experiments were conducted at 1609 m above sea level using a full exhaust flow dilution tunnel method identical to that used for heavy-duty engine Federal Test Procedure (FTP) testing. Diesel trucks averaged 0.170 g/min THC, 1.183 g/min CO, 1.416 g/min NOx, and 0.030 g/min PM. Diesel buses averaged 0.137 g/min THC, 1.326 g/min CO, 2.015 g/min NOx, and 0.048 g/min PM. Results are compared to idle emission factors from the MOBILE5 and PART5 inventory models. The models significantly (45-75%) overestimate emissions of THC and CO in comparison with results measured from the fleet of vehicles examined in this study. Measured NOx emissions were significantly higher (30-100%) than model predictions. For the pre-1999 (pre-consent decree) truck engines examined in this study, idle NOx emissions increased with model year with a linear fit (r2 = 0.6). PART5 nationwide fleet average emissions are within 1 order of magnitude of emissions for the group of vehicles tested in this study. Aldehyde emissions for bus idling averaged 6 mg/min. The VOF averaged 19% of total PM for buses and 49% for trucks. CNG vehicle idle emissions averaged 1.435 g/min for THC, 1.119 g/min for CO, 0.267 g/min for NOx, and 0.003 g/min for PM. The g/min PM emissions are only a small fraction of g/min PM emissions during vehicle driving. However, idle emissions of NOx, CO, and THC are significant in comparison with driving emissions.

40 CFR 600.208-12 - Calculation of FTP-based and HFET-based fuel economy and carbon-related exhaust emission values...

Science.gov (United States)

2010-07-01

...-based fuel economy and carbon-related exhaust emission values for a model type. 600.208-12 Section 600... ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later...-based and HFET-based fuel economy and carbon-related exhaust emission values for a model type. (a) Fuel...

Emission of biocides from treated materials: test procedures for water and air.

Science.gov (United States)

Schoknecht, Ute; Wegner, Robby; Horn, Wolfgang; Jann, Oliver

2003-01-01

Methods for the determination of biocide emissions from treated materials into water and air were developed and tested in order to support a comparative ecological assessment of biocidal products. Leaching tests, experiments with simulated rain, extraction cleaning of carpets and emission chamber tests were performed with a series of treated materials. The experiments focused on the effect of changes in the procedure as well as characteristics of the specimens and demonstrate the suitability of the proposed methods for biocides of different product types. It was demonstrated that emissions of biocides into water can be compared on the basis of leaching tests in which the emission kinetics of the active ingredients are recorded. However, the water volume per surface area and the timetable for water changes have to be defined in such tests. Functions of flux rates related to time can be well described for inorganic compounds, whereas modelling of the data is more complicated for organic substances. Emission chamber tests using 20-litre and 23-litre glass exsiccators, originally developed to study volatile organic compounds, were successfully adapted for the investigation of the emission of biocides from treated materials which are usually semi volatile organic compounds. However test parameters and the method of analysis have to be adapted to the substances to be determined. Generally, it was found that the emission curves for the semi volatile organic compounds investigated differ from those of volatile organic compounds.

Emission Performance of Low Cetane Naphtha as Drop-In Fuel on a Multi-Cylinder Heavy-Duty Diesel Engine and Aftertreatment System

Energy Technology Data Exchange (ETDEWEB)

LeePhD, John [Aramco Services Company; TzanetakisPhD, Tom [Aramco Services Company; Travers, Michael [Aramco Services Company; Storey, John Morse [ORNL; DeBusk, Melanie Moses [ORNL; Lance, Michael J [ORNL; Partridge Jr, William P [ORNL

2017-01-01

With higher volatility and longer ignition delay characteristics than typical diesel fuel, low cetane naphtha fuel has been shown to promote partially premixed combustion and produce lower soot for improved fuel economy. In this study, emission performance of low cetane, low octane naphtha (CN 35, RON 60) as a drop-in fuel was examined on a MY13 Cummins ISX15 6-cylinder heavy-duty on-highway truck engine and aftertreatment system. Using the production hardware and development calibrations, both the engine-out and tailpipe emissions of naphtha and ultra-low sulfur diesel (ULSD) fuels were examined during the EPA s heavy-duty emission testing cycles. Without any modification to the calibrations, the tailpipe emissions were comparable when using naphtha or ULSD on the heavy duty Federal Test Procedure (FTP) and ramped modal cycle (RMC) test cycles. Overall lower CO2 emissions and fuel consumption were also measured for naphtha due in part to its higher heating value and higher hydrogen to carbon ratio. Engine-out and tailpipe NOx emissions were lower for naphtha fuel at the same catalyst conversion levels and measured particulate matter (PM) emissions were also lower when using naphtha due to its higher volatility and lower aromatic content compared to ULSD. To help assess the potential impact on diesel particulate filter design and operation, engine-out PM samples were collected and characterized at the B50 operating point. A significant reduction in elemental carbon (EC) within the particulate emissions was found when using naphtha compared to ULSD.

Standard audit procedure for continuous emission monitors and ambient air monitoring instruments

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-06-15

The instruments were published in an operational policy manual in 2009. This policy aims to introduce standard audit criteria that can be used to determine if continuous emission monitors and ambient air monitoring devices are operating within acceptable parameters. Before delivering upscale points of the instrument to be audited, each one of the audit equipment used in the field is required to be at normal operating conditions. Before the beginning of the audit, each one of the meteorological and flow measurement equipment is required to be conditioned to current conditions. If the audit fails, the instrument will have to be audited quarterly. The establishment of specific procedures based on instrument manufacturer or certifying body operational standards is required in the case of non-continuous monitoring instruments presenting operational principles outside of the audit procedures listed in the document.

Adaptação do modelo de emissão modal CMEM para a frota da cidade de Maringá, Estado do Paraná, Brasil = Adaptation of CMEM modal emission model to the fleet of the city of Maringá, Paraná State, Brazil

Directory of Open Access Journals (Sweden)

Ed Pinheiro Lima

2011-01-01

Full Text Available Este artigo descreve a adaptação do modelo de emissão modal CMEM à frota da cidade de Maringá, Estado do Paraná, Brasil. Foram adotados como parâmetros de referência os fatores médios ponderados de emissão e de consumo determinados para a cidade. Esses fatores ponderados foram obtidos para cada fase do Proconve por meio dos fatores médios de emissão, corrigidos pelos fatores de deterioração do AP-42 da EPA e de consumo. Para cada fase do Proconve, foi associado um veículo representativo. Para cada veículo representativo, os parâmetros do modelo CMEM foram ajustados para aproximar-se aos fatores de emissão e consumo de referência. Observou-se que os fatores do AP42 tendem a representar melhor a deterioração da frota, principalmente para veículos mais antigos. A comparação com resultados do ciclo FTP, desagregados por fase, demonstrou variações percentuais mais significativas do que no valor total do ciclo. This paper describes the CMEM modal emission model adaptation to the fleet of the city of Maringá, Parana state, Brazil. Weighted averagefactors of determined emission and consumption for the city were adopted as reference parameters. These weighed factors were obtained for each PROCONVE phase through consumption and emission average factors, the latter corrected by AP-42 deterioration factors. For each Proconve phase a composite vehicle was associated. For each composite vehicle, the CMEM model parameters were adjusted to approach emission and consumption reference factors. It was observed AP42 deterioration factors tend to better represent the deterioration of the fleet, especially old vehicles. The comparison with FTP cycleresults, disaggregated by phase, demonstrated more significant percentile variations than the total value of the cycle.

Final report for measurement of primary particulate matter emissions from light-duty motor vehicles

Energy Technology Data Exchange (ETDEWEB)

Norbeck, J. M.; Durbin, T. D.; Truex, T. J.

1998-12-31

This report describes the results of a particulate emissions study conducted at the University of California, Riverside, College of Engineering-Center for Environmental Research and Technology (CE-CERT) from September of 1996 to August of 1997. The goal of this program was to expand the database of particulate emissions measurements from motor vehicles to include larger numbers of representative in-use vehicles. This work was co-sponsored by the Coordinating Research Council (CRC), the South Coast Air Quality Management District (SCAQMD), and the National Renewable Energy Laboratory (NREL) and was part of a larger study of particulate emissions being conducted in several states under sponsorship by CRC. For this work, FTP particulate mass emission rates were determined for gasoline and diesel vehicles, along with the fractions of particulates below 2.5 and 10 microns aerodynamic diameter. A total of 129 gasoline-fueled vehicles and 19 diesel-fueled vehicles were tested as part of the program.

Evaluation of energy consumption, emissions and cost of plug-in hybrid vehicles

International Nuclear Information System (INIS)

Silva, Carla; Ross, Marc; Farias, Tiago

2009-01-01

Plug-in hybrid vehicles (PHEVs) are gaining attention over the world due to their ability to reduce gasoline/diesel consumption by using electricity from the grid. Despite the efforts of Society of Automotive Engineers Recommended Practice SAE J1711, it has not yet been established a worldwide methodology for calculation of fuel consumption and emission factors when regarding emission standards, with distinct driving cycles. This paper intends to contribute to the creation of this broader methodology, based on SAE J1711, aiming a fair comparison among vehicle technologies, and giving insight on electric grid impact and on CO 2 life-cycle emissions. The methodology was applied to two simulated PHEVs exploring two different powertrain configurations: series and parallel; different driving cycles: CAFE, FTP75, NEDC and JC08; different driving distances (specially analyzing the average commuting daily distance of 20 km) and different user behaviours regarding battery recharging. CO 2 emissions were calculated for fuel consumption, electricity generation and cradle-to-grave. Electric grid power demand was estimated. Maintenance, manufacturer and use costs were discussed.

40 CFR 600.206-08 - Calculation and use of FTP-based and HFET-based fuel economy values for vehicle configurations.

Science.gov (United States)

2010-07-01

... EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures... economy value exists for an electric vehicle configuration, all values for that vehicle configuration are... HFET-based fuel economy values for vehicle configurations. 600.206-08 Section 600.206-08 Protection of...

Dynamic simulation of a fuel cell hybrid vehicle during the federal test procedure-75 driving cycle

International Nuclear Information System (INIS)

Kang, Sanggyu; Min, Kyoungdoug

2016-01-01

Highlights: • Development of a FCHV dynamic model. • Integration of a PEMFC system dynamic model with the electric vehicle model. • Investigation of the dynamic behavior of the FCEV and PEMFC system during FTP-75. • Capturing the dynamic correlation among components in PEMFC system during FTP-75. - Abstract: The dynamic behavior of a proton exchange membrane fuel cell (PEMFC) system is a crucial factor to ensure the safe and effective operation of fuel cell hybrid vehicles (FCHVs). Specifically, water and thermal management are critical to stabilize the performance of the PEMFC during severe load changes. In the present study, the FCHV dynamic model is developed. The dynamic model of the PEMFC system developed by Matlab–Simulink® is integrated into the electric vehicle model embedded in the Amesim®. The dynamic model of the PEMFC system is composed of a PEMFC stack, an air feeding system, and a thermal management system (TMS). The component models of PEMFC, a shell-and-tube gas-to-gas membrane humidifier, and a heat exchanger are validated via a comparison with the experimental data. The FCHV model is simulated during a federal test procedure (FTP)-75 driving cycle. One system configuration and control strategy is adopted to attain optimal water and thermal management in the PEMFC system. The vehicle speed obtained from the FCHV model aptly tracks the target velocity profile of the FTP-75 cycle within an error of ±0.5%. The dynamic behavior and correlation of each component in the PEMFC system is investigated. The mass and heat transfer in the PEMFC, a humidifier, and a heat exchanger are resolved to determine the species concentration and the temperature more accurately with discretization in the flow’s perpendicular direction. Discretization in the flow parallel direction of humidifier and heat exchanger model makes it possible to capture the distribution of the characteristics. The present model can be used to attain the optimization of the system

A pilot study to determine medical laser generated air contaminant emission rates for a simulated surgical procedure.

Science.gov (United States)

Lippert, Julia F; Lacey, Steven E; Lopez, Ramon; Franke, John; Conroy, Lorraine; Breskey, John; Esmen, Nurtan; Liu, Li

2014-01-01

The U.S. Occupational Safety and Health Administration (OSHA) estimates that half a million health-care workers are exposed to laser surgical smoke each year. The purpose of this study was to establish a methodology to (1) estimate emission rates of laser-generated air contaminants (LGACs) using an emission chamber, and to (2) perform a screening study to differentiate the effects of three laser operational parameters. An emission chamber was designed, fabricated, and assessed for performance to estimate the emission rates of gases and particles associated with LGACs during a simulated surgical procedure. Two medical lasers (Holmium Yttrium Aluminum Garnet [Ho:YAG] and carbon dioxide [CO2]) were set to a range of plausible medical laser operational parameters in a simulated surgery to pyrolyze porcine skin generating plume in the emission chamber. Power, pulse repetition frequency (PRF), and beam diameter were evaluated to determine the effect of each operational parameter on emission rate using a fractional factorial design. The plume was sampled for particulate matter and seven gas phase combustion byproduct contaminants (benzene, ethylbenzene, toluene, formaldehyde, hydrogen cyanide, carbon dioxide, and carbon monoxide): the gas phase emission results are presented here. Most of the measured concentrations of gas phase contaminants were below their limit of detection (LOD), but detectable measurements enabled us to determine laser operation parameter influence on CO2 emissions. Confined to the experimental conditions of this screening study, results indicated that beam diameter was statistically significantly influential and power was marginally statistically significant to emission rates of CO2 when using the Ho:YAG laser but not with the carbon dioxide laser; PRF was not influential vis-a-vis emission rates of these gas phase contaminants.

Gasoline reformulation to reduce exhaust emissions in Finnish conditions. Influence of sulphur and benzene contents of gasoline on exhaust emissions

International Nuclear Information System (INIS)

Kytoe, M.; Aakko, P.; Lappi, M.

1994-01-01

At earlier stages of the study it was found that the exhaust emissions from cars are reduced when using fuels with no more than 4 wt% of oxygen. At this stage of the study the work focused on impacts of the sulphur and benzene content of gasoline on exhaust emissions in Finland. Sulphur in gasoline retards the operation of the catalyst, and consequently the exhaust emissions of catalyst cars increase if the sulphur content of the fuel increases. In the present study, evaporation during refuelling were measured for fuels with varying vapour pressures and benzene contents of gasoline. The total hydrocarbon evaporation was reduced by 22 % (10 g) when the vapour pressure of gasoline was reduced from 85 kPa to 65 kPa. Correspondingly, benzene evaporation during refuelling was reduced to a third when the benzene content of the fuel was reduced from the level of 3 wt% to 1 wt%. The reduction of the sulphur content of gasoline from 500 ppm to 100 ppm affected regulated exhaust emissions from the catalyst car at +22 deg C as follows: CO emission was reduced on average by 14 % (0.175 g/km), CH emission by 7 % (0.010 g/km) and NO x emission by 9 % (0.011 g/km). At-7 deg C the percentual changes were smaller. When the benzene content of the fuel was reduced from 3 wt% to 1 wt%, the benzene emission from the catalyst cars was reduced by 20-30 % and from the non-catalyst cars on average by 30 % both at +22 deg C and -7 deg C. The benzene emission ranged 3-22 mg/km for the catalyst cars and 40-90 mg/km for the non-catalyst cars at +22 deg C in the FTP test

77 FR 65823 - Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures

Science.gov (United States)

2012-10-31

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Parts 87 [EPA-HQ-OAR-2010-0687; FRL-9678-1] RIN 2060-AO70 Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures Correction In rule document 2012-13828 appearing on pages 36341-36386 in the issue of Monday, June 18, 2012, make the following corrections: Sec. 87.2...

Effect of ethanol fuel additive on diesel emissions.; TOPICAL

International Nuclear Information System (INIS)

Cole, R. L.; Poola, R. B.; Sekar, R.; Schaus, J. E.; McPartlin, P.

2001-01-01

Engine-out emissions from a Volkswagen model TDI engine were measured for three different fuels: neat diesel fuel, a blend of diesel fuel and additives containing 10% ethanol, and a blend of diesel fuel and additives containing 15% ethanol. The test matrix covered five speeds from 1,320 to 3,000 rpm, five torques from 15 Nm to maximum plus the 900-rpm idle condition, and most of the points in the FTP-75 and US-06 vehicle tests. Emissions of particulate matter (PM), nitrogen oxides (NO(sub x)), unburned hydrocarbons (HCs), and carbon monoxide (CO) were measured at each point, as were fuel consumption, exhaust oxygen, and carbon dioxide output. PM emissions were reduced up to 75% when ethanol-diesel blends were used instead of neat diesel fuel. Significant reductions in PM emissions occurred over one-half to two-thirds of the test matrix. NO(sub x) emissions were reduced by up to 84%. Although the regions of reduced NO(sub x) emissions were much smaller than the regions of reduced PM emissions, there was considerable overlap between the two regions where PM emissions were reduced by up to 75% and NO(sub x) emissions were reduced by up to 84%. Such simultaneous reduction of both PM and NO(sub x) emissions would be difficult to achieve by any other means. HC and CO emissions were also reduced in the regions of reduced PM and NO(sub x) emissions that overlapped. Because the ethanol-diesel blends contain less energy on both a per-unit-mass basis and a per-unit-volume basis, there was a reduction in maximum torque of up to 10% and an increase in brake-specific fuel consumption of up to 7% when these blends were used

Particulate emission rates from light-duty vehicles in the South Coast Air Quality Management District

International Nuclear Information System (INIS)

Durbin, T.D.; Norbeck, J.M.; Smith, M.R.; Truex, T.J.

1999-01-01

This paper presents the results of a particulate emission rate study conducted on 129 light-duty gasoline and 19 light-duty diesel vehicles for the Coordinating Research Council's (CRC's) Project E-24-2. Total particulate emission rates for newer gasoline vehicles were low with modest increases with vehicle age and older technology. Average FTP particulate emission rates as a function of model year for gasoline vehicles were found to be 2.5 mg/mi for 1991 and newer models, 14.4 mg/mi for 1986--1990 models, 49.0 mg/mi for 1981--1985 models, and 33.8 mg/mi for 1980 and older models. High gaseous emitters were found to have approximately 5--10 times the particulate emission rates of normal emitters. The diesel vehicles had an average particulate emission rate of 561 mg/mi. It should be noted that the light-duty diesel vehicles were predominantly older, pre-1985 vehicles; the 1985 and newer diesel vehicles had substantially lower particulate emissions, i.e., less than 100 mg/mi. Emission inventory estimates in the South Coast Air Basin based on the fleet emission rates were higher than those obtained using the default values in EMFAC7G, due primarily to the contribution of high emitters

Participation of the public in licensing procedures under the Atomic Energy Act and the Federal Emission Control Act

International Nuclear Information System (INIS)

Hett, F.T.

1994-01-01

Section 7 of the Atomic Energy Act (AtG), section 4 of the Federal Emission Control Act (BImSchG), the Nuclear Installations Licensing Ordinance (AtVfV), and the Ninth Ordinance on the Implementation of the BImSchG (Principles of the licensing procedure) require participation of the public in the procedure before administrative provisions or decisions are issued. The book presents the legally prescribed steps at which participation of the public is mandatory, for the simple case (only one license on the agenda), and for the multi-stage licensing procedure: preliminary negotiations / filling of applications for a license and filing of documents / public announcement of projects / access to files / objections / preclusion of delayed objections / public hearing and other expert discussions / termination of procedure, decision-making by the authorities / decisions on subdivision of procedure into defined stages / modification of the procedure. The analysis of the functions of participation of the public examines the following goals: information / representation of interests / reconciliation of interests / legitimation / control / protection of rights / support. Finally, the book explains the principles of the Constitution demanding participation of the public: human dignity / democracy / rule of law / anticipated effects of the right to have recourse to the courts / civil rights. (orig./HP) [de

Quality-assurance procedures: Method 5G determination of particulate emissions from wood heaters from a dilution tunnel sampling location

Energy Technology Data Exchange (ETDEWEB)

Ward, T.E.; Hartman, M.W.; Olin, R.C.; Rives, G.D.

1989-06-01

Quality-assurance procedures are contained in this comprehensive document intended to be used as an aid for wood-heater manufacturers and testing laboratories in performing particulate matter sampling of wood heaters according to EPA protocol, Method 5G. These procedures may be used in research and development, and as an aid in auditing and certification testing. A detailed, step-by-step quality assurance guide is provided to aid in the procurement and assembly of testing apparatus, to clearly describe the procedures, and to facilitate data collection and reporting. Suggested data sheets are supplied that can be used as an aid for both recordkeeping and certification applications. Throughout the document, activity matrices are provided to serve as a summary reference. Checklists are also supplied that can be used by testing personnel. Finally, for the purposes of ensuring data quality, procedures are outlined for apparatus operation, maintenance, and traceability. These procedures combined with the detailed description of the sampling and analysis protocol will help ensure the accuracy and reliability of Method 5G emission-testing results.

Effect of Top-Region Area of Flat-Top Pyramid Patterned Sapphire Substrate on the Optoelectronic Performance of GaN-Based Light-Emitting Diodes

Directory of Open Access Journals (Sweden)

Hsu-Hung Hsueh

2016-01-01

Full Text Available The flat-top pyramid patterned sapphire substrates (FTP-PSSs have been prepared for the growth of GaN epilayers and the fabrication of lateral-type light-emitting diodes (LEDs with an emission wavelength of approximately 470 nm. Three kinds of FTP-PSSs, which were denoted as FTP-PSS-A, FTP-PSS-B, and FTP-PSS-C, respectively, were formed through the sequential wet etching processes. The diameters of circle areas on the top regions of these three FTP-PSSs were 1, 2, and 3 μm, respectively. Based on the X-ray diffraction results, the full-width at half-maximum values of rocking curves at (002 plane for the GaN epilayers grown on conventional sapphire substrate (CSS, FTP-PSS-A, FTP-PSS-B, and FTP-PSS-C were 412, 238, 346, and 357 arcsec, while these values at (102 plane were 593, 327, 352, and 372 arcsec, respectively. The SpeCLED-Ratro simulation results reveal that the LED prepared on FTP-PSS-A has the highest light extraction efficiency than that of the other devices. At an injection current of 350 mA, the output powers of LEDs fabricated on CSS, FTP-PSS-A, FTP-PSS-B, and FTP-PSS-C were 157, 254, 241, and 233 mW, respectively. The results indicate that both the crystal quality of GaN epilayer and the light extraction of LED can be improved via the use of FTP-PSS, especially for the FTP-PSS-A.

Emission line galaxies and active galactic nuclei in WINGS clusters

Science.gov (United States)

Marziani, P.; D'Onofrio, M.; Bettoni, D.; Poggianti, B. M.; Moretti, A.; Fasano, G.; Fritz, J.; Cava, A.; Varela, J.; Omizzolo, A.

2017-03-01

We present the analysis of the emission line galaxies members of 46 low-redshift (0.04 employing diagnostic diagrams. We examined the emission line properties and frequencies of star-forming galaxies, transition objects, and active galactic nuclei (AGNs: LINERs and Seyferts), unclassified galaxies with emission lines, and quiescent galaxies with no detectable line emission. A deficit of emission line galaxies in the cluster environment is indicated by both a lower frequency, and a systematically lower Balmer emission line equivalent width and luminosity with respect to control samples; this implies a lower amount of ionized gas per unit mass and a lower star formation rate if the source is classified as Hii region. A sizable population of transition objects and of low-luminosity LINERs (≈ 10-20% of all emission line galaxies) are detected among WINGS cluster galaxies. These sources are a factor of ≈1.5 more frequent, or at least as frequent, as in control samples with respect to Hii sources. Transition objects and LINERs in clusters are most affected in terms ofline equivalent width by the environment and appear predominantly consistent with so-called retired galaxies. Shock heating can be a possible gas excitation mechanism that is able to account for observed line ratios. Specific to the cluster environment, we suggest interaction between atomic and molecular gas and the intracluster medium as a possible physical cause of line-emitting shocks. The data whose description is provided in Table B.1, and emission line catalog of the WINGS database are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/599/A83

Advanced CIDI Emission Control System Development

Energy Technology Data Exchange (ETDEWEB)

Lambert, Christine

2006-05-31

Ford Motor Company, with ExxonMobil and FEV, participated in the Department of Energy's (DOE) Ultra-Clean Transportation Fuels Program with the goal to develop an innovative emission control system for light-duty diesel vehicles. The focus on diesel engine emissions was a direct result of the improved volumetric fuel economy (up to 50%) and lower CO2 emissions (up to 25%) over comparable gasoline engines shown in Europe. Selective Catalytic Reduction (SCR) with aqueous urea as the NOx reductant and a Catalyzed Diesel Particulate Filter (CDPF) were chosen as the primary emission control system components. The program expected to demonstrate more than 90% durable reduction in particulate matter (PM) and NOx emissions on a light-duty truck application, based on the FTP-75 drive cycle. Very low sulfur diesel fuel (<15 ppm-wt) enabled lower PM emissions, reduced fuel economy penalty due to the emission control system and improved long-term system durability. Significant progress was made toward a durable system to meet Tier 2 Bin 5 emission standards on a 6000 lbs light-duty truck. A 40% reduction in engine-out NOx emissions was achieved with a mid-size prototype diesel engine through engine recalibration and increased exhaust gas recirculation. Use of a rapid warm-up strategy and urea SCR provided over 90% further NOx reduction while the CDPF reduced tailpipe PM to gasoline vehicle levels. Development work was conducted to separately improve urea SCR and CDPF system durability, as well as improved oxidation catalyst function. Exhaust gas NOx and ammonia sensors were also developed further. While the final emission control system did not meet Tier 2 Bin 5 NOx after 120k mi of aging on the dynamometer, it did meet the standards for HC, NMOG, and PM, and an improved SCR catalyst was shown to have potential to meet the NOx standard, assuming the DOC durability could be improved further. Models of DOC and SCR function were developed to guide the study of several key

40 CFR 1065.10 - Other procedures.

Science.gov (United States)

2010-07-01

... importance of pursuing changes to the procedures: (i) Whether supplemental emission standards or other... procedures, such as those of the California Air Resources Board or the International Organization for... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Other procedures. 1065.10 Section 1065...

40 CFR 205.54 - Test procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Test procedures. 205.54 Section 205.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Medium and Heavy Trucks § 205.54 Test procedures. The procedures described...

Implementation of Portable Emissions Measurement Systems (PEMS) for the Real-driving Emissions (RDE) Regulation in Europe.

Science.gov (United States)

Giechaskiel, Barouch; Vlachos, Theodoros; Riccobono, Francesco; Forni, Fausto; Colombo, Rinaldo; Montigny, Francois; Le-Lijour, Philippe; Carriero, Massimo; Bonnel, Pierre; Weiss, Martin

2016-12-04

Vehicles are tested in controlled and relatively narrow laboratory conditions to determine their official emission values and reference fuel consumption. However, on the road, ambient and driving conditions can vary over a wide range, sometimes causing emissions to be higher than those measured in the laboratory. For this reason, the European Commission has developed a complementary Real-Driving Emissions (RDE) test procedure using the Portable Emissions Measurement Systems (PEMS) to verify gaseous pollutant and particle number emissions during a wide range of normal operating conditions on the road. This paper presents the newly-adopted RDE test procedure, differentiating six steps: 1) vehicle selection, 2) vehicle preparation, 3) trip design, 4) trip execution, 5) trip verification, and 6) calculation of emissions. Of these steps, vehicle preparation and trip execution are described in greater detail. Examples of trip verification and the calculations of emissions are given.

Microwave-assisted versus conventional decomposition procedures applied to a ceramic potsherd standard reference material by inductively coupled plasma atomic emission spectrometry

Energy Technology Data Exchange (ETDEWEB)

Papadopoulou, D.N.; Zachariadis, G.A.; Anthemidis, A.N.; Tsirliganis, N.C.; Stratis, J.A

2004-03-03

Inductively coupled plasma atomic emission spectrometry (ICP-AES) is a powerful, sensitive analytical technique with numerous applications in chemical characterization including that of ancient pottery, mainly due to its multi-element character, and the relatively short time required for the analysis. A critical step in characterization studies of ancient pottery is the selection of a suitable decomposition procedure for the ceramic matrix. The current work presents the results of a comparative study of six decomposition procedures applied on a standard ceramic potsherd reference material, SARM 69. The investigated decomposition procedures included three microwave-assisted decomposition procedures, one wet decomposition (WD) procedure by conventional heating, one combined microwave-assisted and conventional heating WD procedure, and one fusion procedure. Chemical analysis was carried out by ICP-AES. Five major (Si, Al, Fe, Ca, Mg), three minor (Mn, Ba, Ti) and two trace (Cu, Co) elements were determined and compared with their certified values. Quantitation was performed at two different spectral lines for each element and multi-element matrix-matched calibration standards were used. The recovery values for the six decomposition procedures ranged between 75 and 110% with a few notable exceptions. Data were processed statistically in order to evaluate the investigated decomposition procedures in terms of recovery, accuracy and precision, and eventually select the most appropriate one for ancient pottery analysis.

On the Performance of the Current MANET Routing Protocols for VoIP, HTTP, and FTP Applications

Directory of Open Access Journals (Sweden)

Waheb A. Jabbar

2014-01-01

Full Text Available The recent advances of ensemble mobile environment of smart devices with embedded sensors have enabled the MANET to play a key role in the smart cities as well as WSN and WMN. However, these smart devices are still limited in terms of energy, processor, and memory. Moreover, the efficient routing for reliable network connectivity at anytime, anywhere, and about everything is still a challenge in multihop wireless networks. This paper evaluates the QoS and energy efficiency of three active routing protocols: (i OLSRv2, a successor to OLSR, (ii DYMO, a successor to both DSR and AODV, and (iii MP-OLSR multipath extension to OLSRv2. In contrast to the related previous works which focused only on CBR traffic without considering the influence of specific traffic types on the performance of routing protocols, this work focused on this area from a different perspective. It evaluates the performance of three internet-based traffic types that can be used in the smart city applications: VoIP, HTTP, and FTP using different simulation models. The impact of the network density, load traffic, and nodes mobility on the considered protocols was evaluated by considering particular performance metrics for each traffic application. Based on the results, the study concludes by presenting useful recommendations for future work.

Reservoir Greenhouse Gas Emissions at Russian HPP

Energy Technology Data Exchange (ETDEWEB)

Fedorov, M. P.; Elistratov, V. V.; Maslikov, V. I.; Sidorenko, G. I.; Chusov, A. N.; Atrashenok, V. P.; Molodtsov, D. V. [St. Petersburg State Polytechnic University (Russian Federation); Savvichev, A. S. [Russian Academy of Sciences, S. N. Vinogradskii Institute of Microbiology (Russian Federation); Zinchenko, A. V. [A. I. Voeikov Main Geophysical Observatory (Russian Federation)

2015-05-15

Studies of greenhouse-gas emissions from the surfaces of the world’s reservoirs, which has demonstrated ambiguity of assessments of the effect of reservoirs on greenhouse-gas emissions to the atmosphere, is analyzed. It is recommended that greenhouse- gas emissions from various reservoirs be assessed by the procedure “GHG Measurement Guidelines for Fresh Water Reservoirs” (2010) for the purpose of creating a data base with results of standardized measurements. Aprogram for research into greenhouse-gas emissions is being developed at the St. Petersburg Polytechnic University in conformity with the IHA procedure at the reservoirs impounded by the Sayano-Shushenskaya and Mainskaya HPP operated by the RusHydro Co.

Emission computed tomography

International Nuclear Information System (INIS)

Budinger, T.F.; Gullberg, G.T.; Huesman, R.H.

1979-01-01

This chapter is devoted to the methods of computer assisted tomography for determination of the three-dimensional distribution of gamma-emitting radionuclides in the human body. The major applications of emission computed tomography are in biological research and medical diagnostic procedures. The objectives of these procedures are to make quantitative measurements of in vivo biochemical and hemodynamic functions

A guide to the emissions certification procedures for alternative fuel aftermarket conversions

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-01

Emissions certification is still relatively new to the aftermarket vehicle conversion industry. Many in the industry think that as soon as a vehicle is converted to operate on compressed natural gas (CNG) or liquefied petroleum gas (LFG), it automatically runs as clean as or cleaner than it did on the conventional fuel. However, recent studies have shown that aftermarket conversions may not always reduce emissions. To achieve emissions benefits, the conversion equipment must be designed and calibrated specifically for the engine and emissions control system on which it has been installed, and the installation and setup must be performed so as to not adversely affect the vehicle`s original emissions performance. The reason for certification, then, is to ensure that these criteria are met, that the vehicle continues to perform properly, and that it continues to satisfy all appropriate emissions standards throughout its useful life. The authors have prepared this guide to help equipment manufacturers, distributors, and installers understand the emissions certification process for aftermarket conversions. The guide gives an overview of the certification requirements established by the US EPA and by the state of California.

Real-world vehicle emission factors in Chinese metropolis city--Beijing.

Science.gov (United States)

Wang, Qi-dong; He, Ke-bin; Huo, Hong; Lents, James

2005-01-01

The dynamometer tests with different driving cycles and the real-world tests are presented. Results indicated the pollutants emission factors and fuel consumption factor with ECE15 + EUDC driving cycle usually take the lowest value and with real world driving cycle occur the highest value, and different driving cycles will lead to significantly different vehicle emission factors with the same vehicle. Relative to the ECE15 + EUDC driving cycle, the increasing rate of pollutant emission factors of CO, NOx and HC are - 0.42-2.99, -0.32-0.81 and -0.11-11 with FTP75 testing, 0.11-1.29, -0.77-0.64 and 0.47-10.50 with Beijing 1997 testing and 0.25-1.83, 0.09-0.75 and - 0.58-1.50 with real world testing. Compared to the carburetor vehicles, the retrofit and MPI + TWC vehicles' pollution emissionfactors decrease with different degree. The retrofit vehicle (Santana) will reduce 4.44%-58.44% CO, -4.95%-36.79% NOx, -32.32%-33.89% HC, and -9.39%-14.29% fuel consumption, and especially that the MPI + TWC vehicle will decrease CO by 82.48%-91.76%, NOx by 44.87%-92.79%, HC by 90.00%-93.89% and fuel consumption by 5.44%-10.55%. Vehicles can cause pollution at a very high rate when operated in high power modes; however, they may not often operate in these high power modes. In analyzing vehicle emissions, it describes the fraction of time that vehicles operate in various power modes. In Beijing, vehicles spend 90% of their operation in low power modes or decelerating.

Micro Fourier Transform Profilometry (μFTP): 3D shape measurement at 10,000 frames per second

Science.gov (United States)

Zuo, Chao; Tao, Tianyang; Feng, Shijie; Huang, Lei; Asundi, Anand; Chen, Qian

2018-03-01

Fringe projection profilometry is a well-established technique for optical 3D shape measurement. However, in many applications, it is desirable to make 3D measurements at very high speed, especially with fast moving or shape changing objects. In this work, we demonstrate a new 3D dynamic imaging technique, Micro Fourier Transform Profilometry (μFTP), which can realize an acquisition rate up to 10,000 3D frame per second (fps). The high measurement speed is achieved by the number of patterns reduction as well as high-speed fringe projection hardware. In order to capture 3D information in such a short period of time, we focus on the improvement of the phase recovery, phase unwrapping, and error compensation algorithms, allowing to reconstruct an accurate, unambiguous, and distortion-free 3D point cloud with every two projected patterns. We also develop a high-frame-rate fringe projection hardware by pairing a high-speed camera and a DLP projector, enabling binary pattern switching and precisely synchronized image capture at a frame rate up to 20,000 fps. Based on this system, we demonstrate high-quality textured 3D imaging of 4 transient scenes: vibrating cantilevers, rotating fan blades, flying bullet, and bursting balloon, which were previously difficult or even unable to be captured with conventional approaches.

40 CFR 86.160-00 - Exhaust emission test procedure for SC03 emissions.

Science.gov (United States)

2010-07-01

... percent relative humidity), a solar heat load intensity of 850 W/m2, and vehicle cooling air flow....161-00. (ii) Turn on the solar heating system. (iii) All vehicle test phases of preconditioning, soak...) Exhaust Emission Measurement Activities. The following activities are performed, when applicable, in order...

Practicability of passenger vehicle driving emission tests according to new European Union procedures

Directory of Open Access Journals (Sweden)

Pielecha Jacek

2017-01-01

Full Text Available The article compares driving test data using the latest legislative proposals applicable to passenger cars. Several measurements were performed on the same test route in accordance with the RDE test guidelines, which requires a number of criteria to be met. These criteria include: the length of the measuring segments, their overall test time share, and the dynamic characteristics of the drive. A mobile device for reading the EOBD System information was used to record the engine and vehicle operating parameters during tests. This allowed for the monitoring of parameters such as: load value, engine speed and vehicle velocity. The obtained results were then analyzed for their compatibility with the RDE procedure requirements. Despite the same research route, the obtained results were not the same. The analysis also uses the two-dimensional operating time share characteristics expressed in vehicle velocity and acceleration co-ordinates. As a result it was possible to compare the dynamic properties, share of operating time and, consequently, to check the validity of conducted drive tests in terms of their practicability and emission values.

Effects of biodiesel on emissions of regulated air pollutants and polycyclic aromatic hydrocarbons under engine durability testing

International Nuclear Information System (INIS)

Hsi-Hsien Yang; Shu-Mei Chien; Mei-Yu Lo; John Chi-Wei Lan; Wen-Chang Lu; Yong-Yuan Ku

2007-01-01

An 80,000-km durability test was performed on two engines using diesel and biodiesel (methyl ester of waste cooking oil) as fuel in order to examine emissions resulting from the use of biodiesel. The test biodiesel (B20) was blended with 80% diesel and 20% methyl ester derived from waste cooking oil. Emissions of regulated air pollutants, including CO, HC, NO x , particulate matter (PM) and polycyclic aromatic hydrocarbons (PAHs) were measured at 20,000-km intervals. The identical-model engines were installed on a standard dynamometer equipped with a dilution tunnel used to measure the pollutants. To simulate real-world driving conditions, emission measurements were made in accordance with the United States Environmental Protection Agency (USEPA) FTP transient cycle guidelines. At 0 km of the durability test, HC, CO and PM emission levels were lower for the B20 engine than those for diesel. After running for 20,000 km and longer, they were higher. However, the deterioration coefficients for these regulated air pollutants were not statistically higher than 1.0, implying that the emission factors do not increase significantly after 80,000 km of driving. Total (gaseous+particulate phase) PAH emission levels for both B20 and diesel decreased as the driving mileage accumulated. However, for the engine using B20 fuel, particulate PAH emissions increased as engine mileage increased. The average total PAH emission factors were 1097 and 1437 μg bhp h -1 for B20 and diesel, respectively. For B20, the benzo[a]pyrene equivalence emission factors were 0.77, 0.24, 0.20, 7.48, 5.43 and 14.1 μg bhp h -1 for 2-, 3-, 4-, 5-, 6-ringed and total PAHs. Results show that B20 use can reduce both PAH emission and its corresponding carcinogenic potency. (author)

Effects of biodiesel on emissions of regulated air pollutants and polycyclic aromatic hydrocarbons under engine durability testing

Energy Technology Data Exchange (ETDEWEB)

Hsi-Hsien Yang; Shu-Mei Chien; Mei-Yu Lo [Chaoyang University of Technology, Wufong (China). Dept. of Environmental Engineering and Management; John Chi-Wei Lan [Yuan Ze University (China). Dept. of Chemical Engineering and Materials Science; Wen-Chang Lu [Industrial Technology Research Institute, Hsinchu (China). New Energy Div.; Yong-Yuan Ku [Automotive Research and Testing Center, Chunhwa (China). Diesel Vehicle Section

2007-11-15

An 80,000-km durability test was performed on two engines using diesel and biodiesel (methyl ester of waste cooking oil) as fuel in order to examine emissions resulting from the use of biodiesel. The test biodiesel (B20) was blended with 80% diesel and 20% methyl ester derived from waste cooking oil. Emissions of regulated air pollutants, including CO, HC, NO{sub x}, particulate matter (PM) and polycyclic aromatic hydrocarbons (PAHs) were measured at 20,000-km intervals. The identical-model engines were installed on a standard dynamometer equipped with a dilution tunnel used to measure the pollutants. To simulate real-world driving conditions, emission measurements were made in accordance with the United States Environmental Protection Agency (USEPA) FTP transient cycle guidelines. At 0 km of the durability test, HC, CO and PM emission levels were lower for the B20 engine than those for diesel. After running for 20,000 km and longer, they were higher. However, the deterioration coefficients for these regulated air pollutants were not statistically higher than 1.0, implying that the emission factors do not increase significantly after 80,000 km of driving. Total (gaseous+particulate phase) PAH emission levels for both B20 and diesel decreased as the driving mileage accumulated. However, for the engine using B20 fuel, particulate PAH emissions increased as engine mileage increased. The average total PAH emission factors were 1097 and 1437 {mu}g bhp h{sup -1} for B20 and diesel, respectively. For B20, the benzo[a]pyrene equivalence emission factors were 0.77, 0.24, 0.20, 7.48, 5.43 and 14.1 {mu}g bhp h{sup -1} for 2-, 3-, 4-, 5-, 6-ringed and total PAHs. Results show that B20 use can reduce both PAH emission and its corresponding carcinogenic potency. (author)

General guidance and procedures for estimating and reporting national GHG emissions for agriculture

International Nuclear Information System (INIS)

Rypdal, K.

2002-01-01

Greenhouse gas (GHG) emissions from agriculture account for a large share of total GHG emissions in most countries. Methane from ruminants, animal manure and rice fields, and nitrous oxide from agricultural soils are among the most important sources. In general, these emission estimates also are more uncertain than most other parts of the GHG emission inventory. IPCC has developed guidelines for estimating and reporting emissions of GHG. These guidelines shall be followed to secure complete, consistent, accurate and transparent reporting of emissions. However, the recommended methodologies are tiered, and choice of methods shall preferably reflect national circumstances, the national importance of a source, and different resources to prepare inventories. A country may also apply a national methodology given that it is well documented and not in conflict with good practice. Emission data reported under the United Nation Framework Convention on Climate Change are subject to external control, and the methodologies are reviewed by experts on agricultural inventories. (au)

Evaluation of slurry preparation procedures for the determination of mercury by axial view inductively coupled plasma optical emission spectrometry using on-line cold vapor generation

International Nuclear Information System (INIS)

Santos, Eder Jose dos; Herrmann, Amanda Beatriz; Antunes Vieira, Mariana; Azzolin Frescura, Vera Lucia; Curtius, Adilson Jose

2005-01-01

Five different slurry preparation procedures were tested, after grinding the solid samples to a particle size ≤53 μm: (1) using aqua regia plus HF, 30 min of sonication, standing time of 24 h followed by another 30 min of sonication; (2) same as the previous one, except that the standing time and the second ultrasound treatment were omitted; (3) same as the previous one, except that HF was not used; (4) same as the previous one, except that the aqua regia was replaced by nitric acid; (5) same as the previous one, except that the acid nitric was replaced by tetramethylammonium hydroxide (TMAH). The Hg vapor was generated on-line, and the emission signal intensity measured at 253.652 nm by axial view inductively coupled plasma optical emission spectrometry. Initially, four experimental conditions were optimized using a multivariate factorial analysis: the concentrations of HCl and of the reducing agent, NaBH 4 , used in the cold vapor generation, and two instrumental parameters, the plasma radiofrequency power and the carrier gas flow rate. The radiofrequency power was statistically significant, but limited to 1.2 kW for practical reasons. The procedures were applied to 11 biological and environmental materials. Both, the slurries and the filtrates were analyzed, using calibration solutions in the same medium as in the slurries. The first three procedures produced results in agreement with the certified values. The two last procedures, using nitric acid or TMHA could not be used for quantitative analysis. For practical reasons, Procedure 3, with a detection limit (3s, n=10) of 0.06 μg g -1 for a sample mass of 20 mg in a final volume of 15 mL is recommended. The relative standard deviations for mercury in the investigated materials, using the recommended procedure, were lower than 12.5%, indicating a good precision for slurry sampling. The recommended procedure is simple, rapid and robust

Electron emission from individual indium arsenide semiconductor nanowires

NARCIS (Netherlands)

Heeres, E.C.; Bakkers, E.P.A.M.; Roest, A.L.; Kaiser, M.A.; Oosterkamp, T.H.; Jonge, de N.

2007-01-01

A procedure was developed to mount individual semiconductor indium arsenide nanowires onto tungsten support tips to serve as electron field-emission sources. The electron emission properties of the single nanowires were precisely determined by measuring the emission pattern, current-voltage curve,

40 CFR 75.35 - Missing data procedures for CO2.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Missing data procedures for CO2. 75.35... procedures for CO2. (a) The owner or operator of a unit with a CO2 continuous emission monitoring system for determining CO2 mass emissions in accordance with § 75.10 (or an O2 monitor that is used to determine CO2...

Aircraft Piston Engine Exhaust Emission Symposium

Science.gov (United States)

1976-01-01

A 2-day symposium on the reduction of exhaust emissions from aircraft piston engines was held on September 14 and 15, 1976, at the Lewis Research Center in Cleveland, Ohio. Papers were presented by both government organizations and the general aviation industry on the status of government contracts, emission measurement problems, data reduction procedures, flight testing, and emission reduction techniques.

Comparison of digestion procedures used for the determination of boron in biological tissues by ICP-AES [inductively-coupled, plasma-atomic emission spectroscopy

International Nuclear Information System (INIS)

Bauer, W.F.; Miller, D.L.; Steele, S.M.

1988-01-01

A study was designed to identify the most accurate and reliable procedures for the digestion of biological tissues prior to the determination of boron by inductively-coupled, plasma-atomic emission spectroscopy (ICP-AES). The four procedures used in this study were an acid bomb digestion and digestions performed in test tubes using perchloric acid and hydrogen peroxide, nitric acid and hydrogen peroxide, and nitric acid alone. Digestions using nitric acid and hydrogen peroxide and nitric acid alone were performed in a manner analogous to the perchloric acid/hydrogen peroxide procedure. The tissues used in the study were from dogs that had been administered a boron compound (Na 2 B 12 H 11 SH) and included two brain tissues, a liver and a tongue. These tissues were selected in order to eliminate results that may be due to surface spiking only. None of the test tube procedures were successful in completely dissolving the samples, as was evidenced by residual color and a coagulated precipitate. The amount of precipitate was much larger for the brain tissues in all cases. The acid bomb digestion and the perchloric acid/hydrogen peroxide procedures gave comparable boron concentrations for all of the tissues in this study. 2 refs., 1 tab

Smoke emissions from a catalytic wood stove

International Nuclear Information System (INIS)

Cowburn, D.A.; Stephens, N.P.J.

1994-01-01

The work reported here was concerned with testing a catalytic wood burning stove (roomheater) following the most applicable UK procedures. The identical stove has also been tested in several other nations to their individual procedures. The results will be submitted to the International Energy Agency (IEA) such that appropriate comparisons can be made. The results comprised: burning rate; an indicative appliance efficiency; heat output; carbon dioxide emissions; carbon monoxide emissions; and smoke emissions. These results were determined with the appliance at three nominal burning rates (high, medium and low). Comparing the results with those obtained in other countries indicates good agreement except when the appliance was operated at low burning rates, under which conditions the UK results indicate significantly worse smoke emissions than those measured by other researchers. (author)

Air pollution prevention manual on emission monitoring. 2. rev. ed.

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-08-15

The Manual on Emission Monitoring covers the need for information about the national practice in the field of emission control at plants, requiring official approval. The legal bases for discontinuous and continuous measurements for emission control at plants, requiring official approval, are treated. Thereby also the European environmental legislation is considered. The publication procedure for testing institutes, which execute such measurements, is described. The execution of discontinuous emission measurements (course of the measurement and measurement requests) and for continuous emission measurement (suitability test, installation, maintenance, functional test and calibration of the automated measuring system) including the evaluation and documentation of the measured values is described. The procedure of remote emission monitoring is explained. The most important measuring procedures (continuous and discontinuous) are reported. The guide also includes an up-to-date list of tested and appropriate measurement devices. Such tested measuring devices are described by their manufacturers. Indications are given as to how the devices function together with their technical data (e. g. parameters from the suitability test). (orig.)

Power train and emission control: allocation procedure by OBD-II system for automotive technology

Science.gov (United States)

Kalita, Porag

2017-06-01

OBD-II, systems were designed to maintain low emissions of in use vehicles, including light and medium duty vehicles. In 1989, the California code of Regulations (CCR) known as OBD - II was adopted by the California Air Resource Board (CARB) and the objective to reduce hydrocarbon (HC) emission caused by malfunction of the vehicles emission control systems. OBD-II provides additional information to engineer for diagnosis and repair of emissions related problems. OBD-II, standardizes on the amount of memory (Freeze Frame) it uses to store the readings of the vehicle sensor when it logs on emission related Intermittent Trouble code (IT). The intent of OBD-II, systems is to detect most vehicle malfunctions when performance of a power train component or system deteriorates to the point that the vehicle’s HC emission exceed standard. The vehicle operator is notified at the time when the vehicle begins to marginally exceed emission standards, by illuminating the Malfunctions Indicator Light (MIL).

40 CFR 76.15 - Test methods and procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Test methods and procedures. 76.15 Section 76.15 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.15 Test methods and procedures. (a) The...

Estimating emissions on vehicular traffic based on projected energy and transport demand on rural roads: Policies for reducing air pollutant emissions and energy consumption

International Nuclear Information System (INIS)

Ozan, Cenk; Haldenbilen, Soner; Ceylan, Halim

2011-01-01

This study deals with the estimation of emissions caused by vehicular traffic based on transport demand and energy consumption. Projected transport demand is calculated with Genetic Algorithm (GA) using population, gross domestic product per capita (GDPPC) and the number of vehicles. The energy consumption is modelled with the GA using the veh-km. The model age of the vehicles and their corresponding share for each year using the reference years is obtained. The pollutant emissions are calculated with estimated transport and energy demand. All the calculations are made in line to meet the European standards. For this purpose, two cases are composed. Case 1: Emissions based on energy consumption, and Case 2: Emissions based on transport demand. The both cases are compared. Three policies are proposed to control demand and the emissions. The policies provided the best results in terms of minimum emissions and the reasonable share of highway and railway mode as 70% and 30% usage for policy I, respectively. The emission calculation procedure presented in this study would provide an alternative way to make policies when there is no adequate data on emission measurement in developing countries. - Research highlights: → Emissions caused by vehicular traffic are modelled. → The pollutant emissions are calculated with estimated transport and energy demand. → All the calculations are made in line with to meet the European standards. → The calculation procedure will provide an alternative way to make policies. → The procedure will help planners to convince politicians to impose policies.

Emissivity-corrected power loss calibration for lock-in thermography measurements on silicon solar cells

International Nuclear Information System (INIS)

Kasemann, Martin; Walter, Benjamin; Meinhardt, Christoph; Ebser, Jan; Kwapil, Wolfram; Warta, Wilhelm

2008-01-01

This paper describes power loss calibration procedures with implemented emissivity correction. The determination of our emissivity correction matrix does neither rely on blackbody reference measurements nor on the knowledge of any sample temperatures. To describe the emissivity-corrected power calibration procedures in detail, we review the theory behind lock-in thermography and show experimentally that the lock-in signal is proportional to the power dissipation in the solar cell. Experiments show the successful application of our emissivity correction procedure, which significantly improves the informative value of lock-in thermography images and the reliability of the conclusions drawn from these images

Criteria and air-toxic emissions from in-use automobiles in the National Low-Emission Vehicle program.

Science.gov (United States)

Baldauf, Rich W; Gabele, Pete; Crews, William; Snow, Richard; Cook, J Rich

2005-09-01

The U.S. Environmental Protection Agency (EPA) implemented a program to identify tailpipe emissions of criteria and air-toxic contaminants from in-use, light-duty low-emission vehicles (LEVs). EPA recruited 25 LEVs in 2002 and measured emissions on a chassis dynamometer using the cold-start urban dynamometer driving schedule of the Federal Test Procedure. The emissions measured included regulated pollutants, particulate matter, speciated hydrocarbon compounds, and carbonyl compounds. The results provided a comparison of emissions from real-world LEVs with emission standards for criteria and air-toxic compounds. Emission measurements indicated that a portion of the in-use fleet tested exceeded standards for the criteria gases. Real-time regulated and speciated hydrocarbon measurements demonstrated that the majority of emissions occurred during the initial phases of the cold-start portion of the urban dynamometer driving schedule. Overall, the study provided updated emission factor data for real-world, in-use operation of LEVs for improved emissions modeling and mobile source inventory development.

On-road emissions of light-duty vehicles in europe.

Science.gov (United States)

Weiss, Martin; Bonnel, Pierre; Hummel, Rudolf; Provenza, Alessio; Manfredi, Urbano

2011-10-01

For obtaining type approval in the European Union, light-duty vehicles have to comply with emission limits during standardized laboratory emissions testing. Although emission limits have become more stringent in past decades, light-duty vehicles remain an important source of nitrogen oxides and carbon monoxide emissions in Europe. Furthermore, persisting air quality problems in many urban areas suggest that laboratory emissions testing may not accurately capture the on-road emissions of light-duty vehicles. To address this issue, we conduct the first comprehensive on-road emissions test of light-duty vehicles with state-of-the-art Portable Emission Measurement Systems. We find that nitrogen oxides emissions of gasoline vehicles as well as carbon monoxide and total hydrocarbon emissions of both diesel and gasoline vehicles generally remain below the respective emission limits. By contrast, nitrogen oxides emissions of diesel vehicles (0.93 ± 0.39 grams per kilometer [g/km]), including modern Euro 5 diesel vehicles (0.62 ± 0.19 g/km), exceed emission limits by 320 ± 90%. On-road carbon dioxide emissions surpass laboratory emission levels by 21 ± 9%, suggesting that the current laboratory emissions testing fails to accurately capture the on-road emissions of light-duty vehicles. Our findings provide the empirical foundation for the European Commission to establish a complementary emissions test procedure for light-duty vehicles. This procedure could be implemented together with more stringent Euro 6 emission limits in 2014. The envisaged measures should improve urban air quality and provide incentive for innovation in the automotive industry.

Blockchain Enhanced Emission Trading Framework in Fashion Apparel Manufacturing Industry

Directory of Open Access Journals (Sweden)

Bailu Fu

2018-04-01

Full Text Available Motivated by the recent blockchain technology originally built for bitcoin transactions, various industries are exploring the opportunities to redefine their existing operational systems. In this study, an innovative environmentally sustainable solution is proposed for the fashion apparel manufacturing industry (FAMI, which is energized by blockchain. Incorporating the Emission Trading Scheme (ETS, and a novel “emission link” system, the proposed framework exposes carbon emission to the public and establishes a feature to reduce the emissions for all key steps of clothing making. Fully compatible with Industry 4.0, blockchain provides decentralization, transparency, automation, and immutability characteristics to the proposed framework. Specifically, the blockchain supported ETS framework, the carbon emissions of clothing manufacturing life cycle, and the emission link powered procedures are introduced in detail. A case study is provided to demonstrate the carbon emission evaluation procedure. Finally, a multi-criteria evaluation is performed to demonstrate the benefits and drawbacks of the proposed system.

Canada`s greenhouse gas emissions inventory

Energy Technology Data Exchange (ETDEWEB)

Jaques, A. [Environment Canada, Ottawa, ON (Canada)

1998-09-01

In 1994, Canada was the seventh largest global emitter of CO{sub 2}. The Kyoto Protocol has made it necessary to continue to improve methods for developing emissions inventories. An emissions inventory was defined as `a comprehensive account of air pollutant emissions and associated data from sources within the inventory area over a specified time frame that can be used to determine the effect of emissions on the environment`. The general approach is to compile large-scale emission estimates under averaged conditions for collective sources and sectors, using data that is available on a sectoral, provincial and national basis. Ideally, continuous emission monitors should be used to develop emissions inventories. Other needed improvements include additional research on emissions data, and increased support for international negotiations on reporting policies and related methodologies, verification procedures and adjustments. 1 ref., 5 figs.

Radio jets and gamma-ray emission in radio-silent narrow-line Seyfert 1 galaxies

Science.gov (United States)

Lähteenmäki, A.; Järvelä, E.; Ramakrishnan, V.; Tornikoski, M.; Tammi, J.; Vera, R. J. C.; Chamani, W.

2018-06-01

We have detected six narrow-line Seyfert 1 (NLS1) galaxies at 37 GHz that were previously classified as radio silent and two that were classified as radio quiet. These detections reveal the presumption that NLS1 galaxies labelled radio quiet or radio silent and hosted by spiral galaxies are unable to launch jets to be incorrect. The detections are a plausible indicator of the presence of a powerful, most likely relativistic jet because this intensity of emission at 37 GHz cannot be explained by, for example, radiation from supernova remnants. Additionally, one of the detected NLS1 galaxies is a newly discovered source of gamma rays and three others are candidates for future detections. 37 GHz data are only available in electronic form at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/614/L1

Tecnical Note: Analysis of non-regulated vehicular emissions by extractive FTIR spectrometry: tests on a hybrid car in Mexico City

Science.gov (United States)

Reyes, F.; Grutter, M.; Jazcilevich, A.; González-Oropeza, R.

2006-11-01

A methodology to acquire valuable information on the chemical composition and evolution of vehicular emissions is presented. The analysis of the gases is performed by passing a constant flow of a sample gas from the tail-pipe into a 10 L multi-pass cell. The absorption spectra within the cell are obtained using an FTIR spectrometer at 0.5 cm-1 resolution along a 13.1 m optical path. Additionally, the total flow from the exhaust is continuously measured from a differential pressure sensor on a textit{Pitot} tube installed at the exit of the exhaust. This configuration aims to obtain a good speciation capability by coadding spectra during 30 s and reporting the emission (in g/km) of both criteria and non-regulated pollutants, such as CO2, CO, NO, SO2, NH3, HCHO and some NMHC, during predetermined driving cycles. The advantages and disadvantages of increasing the measurement frequency, as well as the effect of other parameters such as spectral resolution, cell volume and flow rate, are discussed. To test and evaluate the proposed technique, experiments were performed on a dynamometer running FTP-75 and typical driving cycles for the Mexico City Metropolitan Area (MCMA) on a Toyota Prius hybrid vehicle. This car is an example of recent marketed automotive technology dedicated to reduced emissions, increasing the need for sensitive detection techniques. This study shows the potential of the proposed technique to measure and report in real time the emissions of a large variety of pollutants, even from a super ultra-low emission vehicle (SULEV). The emissions of HC's, NOx, CO and CO2 obtained here were compared to experiments performed in other locations with the same model vehicle. The proposed technique provides a tool for future studies comparing in detail the emissions of vehicles using alternative fuels and emission control systems.

Tecnical Note: Analysis of non-regulated vehicular emissions by extractive FTIR spectrometry: tests on a hybrid car in Mexico City

Directory of Open Access Journals (Sweden)

F. Reyes

2006-01-01

Full Text Available A methodology to acquire valuable information on the chemical composition and evolution of vehicular emissions is presented. The analysis of the gases is performed by passing a constant flow of a sample gas from the tail-pipe into a 10 L multi-pass cell. The absorption spectra within the cell are obtained using an FTIR spectrometer at 0.5 cm−1 resolution along a 13.1 m optical path. Additionally, the total flow from the exhaust is continuously measured from a differential pressure sensor on a extit{Pitot} tube installed at the exit of the exhaust. This configuration aims to obtain a good speciation capability by coadding spectra during 30 s and reporting the emission (in g/km of both criteria and non-regulated pollutants, such as CO2, CO, NO, SO2, NH3, HCHO and some NMHC, during predetermined driving cycles. The advantages and disadvantages of increasing the measurement frequency, as well as the effect of other parameters such as spectral resolution, cell volume and flow rate, are discussed. To test and evaluate the proposed technique, experiments were performed on a dynamometer running FTP-75 and typical driving cycles for the Mexico City Metropolitan Area (MCMA on a Toyota Prius hybrid vehicle. This car is an example of recent marketed automotive technology dedicated to reduced emissions, increasing the need for sensitive detection techniques. This study shows the potential of the proposed technique to measure and report in real time the emissions of a large variety of pollutants, even from a super ultra-low emission vehicle (SULEV. The emissions of HC's, NOx, CO and CO2 obtained here were compared to experiments performed in other locations with the same model vehicle. The proposed technique provides a tool for future studies comparing in detail the emissions of vehicles using alternative fuels and emission control systems.

Implementación de un servidor FTP utilizando el modelo cliente/servidor mediante el uso de sockets en lenguaje c UNIX con el fin de mejorar los tiempos de respuesta en la red

OpenAIRE

Murillo, Juan de Dios; Caamaño Polini, Santiago

2016-01-01

Este trabajo pretende evaluar la latencia en la transferencia de archivos utilizando un servidor FTP con un modelo cliente-servidor empleando una computadora con el sistema operativo Fedora para ejecutar el código del modelo cliente/servidor con sockets en lenguaje C UNIX, con el fin de simular un servidor que contiene archivos con diferentes formatos y tamaños, y medir la latencia de la transmisión al subir y descargar los archivos del servidor, usando diferentes tamaños de buffer. Con los r...

40 CFR 1039.501 - How do I run a valid emission test?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false How do I run a valid emission test? 1039.501 Section 1039.501 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Procedures § 1039.501 How do I run a valid emission test? (a) Use the equipment and procedures for...

Positron emission tomography

International Nuclear Information System (INIS)

Paans, A.M.J.

1981-01-01

Positron emitting radiopharmaceuticals have special applications in in-vivo studies of biochemical processes. The combination of a cyclotron for the production of radionuclides and a positron emission tomograph for the registration of the distribution of radioactivity in the body enables the measurement of local radioactivity concentration in tissues, and opens up new possibilities in the diagnosis and examination of abnormalities in the metabolism. The principles and procedures of positron emission tomography are described and the necessary apparatus considered, with emphasis on the positron camera. The first clinical applications using 55 Co bloemycine for tumor detection are presented. (C.F.)

40 CFR 86.1246-96 - Fuel dispensing spitback procedure.

Science.gov (United States)

2010-07-01

...) Evaporative Emission Test Procedures for New Gasoline-Fueled, Natural Gas-Fueled, Liquefied Petroleum Gas... collecting spitback emissions to the nearest 0.01 gram. (d) Drain the fuel tank(s) and fill with test fuel, as specified in § 86.1213, to 10 percent of the reported nominal fuel tank capacity. The fuel cap(s...

Theory of a spherical emissive probe in a low-density isotropic plasma

International Nuclear Information System (INIS)

Din, A.

2010-01-01

Emissive probes are widely being used by plasma experimentalists to determine plasma parameters. Here, a fairly general spherical-emissive-probe scenario based on trajectory integration of the Vlasov equation is formulated and specialized to the particular non-emissive situation considered by Bernstein and Rabinowitz (1959), which is monoenergetic isotropic ions and Boltzmann-distributed electrons originating from the plasma. Then, this formalism together with our newly developed analytic-numerical matching procedure is used for finding the potential profile in the entire plasma-probe transition (PPT) region, consisting of the 'inward' and 'outward' sheath solutions, and the quasineutral (plasma) solution. The analytically expanded outward sheath and plasma solutions, the quasineutral solution and the related matching procedure represent genuinely new results in the context of this particular non-emissive probe scenario, however with the underlying methodology also applicable to other probe scenarios in the future. For the emissive case we consider, in addition to the plasma ions and electrons of the Bernstein and Rabinowitz scenario, electrons emitted from the probe surface with zero tangential velocity and a 'waterbag' distribution with respect to the radial velocity. Using our newly developed numerical matching procedure, we calculate the entire potential profile also for this emissive case. Comparison of the potential profiles for the emissive and non-emissive cases shows visible differences, thus demonstrating the effect of electron emission from the probe. To our knowledge, the present work represents the first attempt at systematically developing a kinetic approach for spherical emissive probes. (author)

40 CFR 1045.501 - How do I run a valid emission test?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false How do I run a valid emission test... Procedures § 1045.501 How do I run a valid emission test? (a) Applicability. This subpart is addressed to you... maximum test speed. (g) Special and alternate procedures. If you are unable to run the duty cycle...

An X-ray survey of the central molecular zone: Variability of the Fe Kα emission line

Science.gov (United States)

Terrier, R.; Clavel, M.; Soldi, S.; Goldwurm, A.; Ponti, G.; Morris, M. R.; Chuard, D.

2018-05-01

There is now abundant evidence that the luminosity of the Galactic super-massive black hole (SMBH) has not always been as low as it is nowadays. The observation of varying non-thermal diffuse X-ray emission in molecular complexes in the central 300 pc has been interpreted as delayed reflection of a past illumination by bright outbursts of the SMBH. The observation of different variability timescales of the reflected emission in the Sgr A molecular complex can be well explained if the X-ray emission of at least two distinct and relatively short events (i.e. about 10 yr or less) is currently propagating through the region. The number of such events or the presence of a long-duration illumination are open questions. Variability of the reflected emission all over of the central 300 pc, in particular in the 6.4 keV Fe Kα line, can bring strong constraints. To do so we performed a deep scan of the inner 300 pc with XMM-Newton in 2012. Together with all the archive data taken over the course of the mission, and in particular a similar albeit more shallow scan performed in 2000-2001, this allows for a detailed study of variability of the 6.4 keV line emission in the region, which we present here. We show that the overall 6.4 keV emission does not strongly vary on average, but variations are very pronounced on smaller scales. In particular, most regions showing bright reflection emission in 2000-2001 significantly decrease by 2012. We discuss those regions and present newly illuminated features. The absence of bright steady emission argues against the presence of an echo from an event of multi-centennial duration and most, if not all, of the emission can likely be explained by a limited number of relatively short (i.e. up to 10 yr) events. Images of the Fe Kα emission as FITS files are only available at the CDS via anonymous ftp to cdsarc.u-strasbg.fr (130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/612/A102

Cost of lower NO x emissions: Increased CO 2 emissions from heavy-duty diesel engines

Science.gov (United States)

Krishnamurthy, Mohan; Carder, Daniel K.; Thompson, Gregory; Gautam, Mridul

This paper highlights the effect of emissions regulations on in-use emissions from heavy-duty vehicles powered by different model year engines. More importantly, fuel economy data for pre- and post-consent decree engines are compared. The objective of this study was to determine the changes in brake-specific emissions of NO x as a result of emission regulations, and to highlight the effect these have had on brake-specific CO 2 emission; hence, fuel consumption. For this study, in-use, on-road emission measurements were collected. Test vehicles were instrumented with a portable on-board tailpipe emissions measurement system, WVU's Mobile Emissions Measurement System, and were tested on specific routes, which included a mix of highway and city driving patterns, in order to collect engine operating conditions, vehicle speed, and in-use emission rates of CO 2 and NO x. Comparison of on-road in-use emissions data suggests NO x reductions as high as 80% and 45% compared to the US Federal Test Procedure and Not-to-Exceed standards for model year 1995-2002. However, the results indicate that the fuel consumption; hence, CO 2 emissions increased by approximately 10% over the same period, when the engines were operating in the Not-to-Exceed region.

Extreme emission-line galaxies out to z ~ 1 in zCOSMOS. I. Sample and characterization of global properties

Science.gov (United States)

Amorín, R.; Pérez-Montero, E.; Contini, T.; Vílchez, J. M.; Bolzonella, M.; Tasca, L. A. M.; Lamareille, F.; Zamorani, G.; Maier, C.; Carollo, C. M.; Kneib, J.-P.; Le Fèvre, O.; Lilly, S.; Mainieri, V.; Renzini, A.; Scodeggio, M.; Bardelli, S.; Bongiorno, A.; Caputi, K.; Cucciati, O.; de la Torre, S.; de Ravel, L.; Franzetti, P.; Garilli, B.; Iovino, A.; Kampczyk, P.; Knobel, C.; Kovač, K.; Le Borgne, J.-F.; Le Brun, V.; Mignoli, M.; Pellò, R.; Peng, Y.; Presotto, V.; Ricciardelli, E.; Silverman, J. D.; Tanaka, M.; Tresse, L.; Vergani, D.; Zucca, E.

2015-06-01

Context. The study of large and representative samples of low-metallicity star-forming galaxies at different cosmic epochs is of great interest to the detailed understanding of the assembly history and evolution of low-mass galaxies. Aims: We present a thorough characterization of a large sample of 183 extreme emission-line galaxies (EELGs) at redshift 0.11 ≤ z ≤ 0.93 selected from the 20k zCOSMOS bright survey because of their unusually large emission line equivalent widths. Methods: We use multiwavelength COSMOS photometry, HST-ACS I-band imaging, and optical zCOSMOS spectroscopy to derive the main global properties of star-forming EELGs, such as sizes, stellar masses, star formation rates (SFR), and reliable oxygen abundances using both "direct" and "strong-line" methods. Results: The EELGs are extremely compact (r50 ~ 1.3 kpc), low-mass (M∗ ~ 107-1010 M⊙) galaxies forming stars at unusually high specific star formation rates (sSFR ≡ SFR/M⋆ up to 10-7 yr-1) compared to main sequence star-forming galaxies of the same stellar mass and redshift. At rest-frame UV wavelengths, the EELGs are luminous and show high surface brightness and include strong Lyα emitters, as revealed by GALEX spectroscopy. We show that zCOSMOS EELGs are high-ionization, low-metallicity systems, with median 12+log (O/H) = 8.16 ± 0.21 (0.2 Z⊙) including a handful of extremely metal-deficient (Universe, EELGs are most often found in relative isolation. While only very few EELGs belong to compact groups, almost one third of them are found in spectroscopically confirmed loose pairs or triplets. Conclusions: The zCOSMOS EELGs are galaxies caught in a transient and probably early period of their evolution, where they are efficiently building up a significant fraction of their present-day stellar mass in an ongoing, galaxy-wide starburst. Therefore, the EELGs constitute an ideal benchmark for comparison studies between low- and high-redshift low-mass star-forming galaxies. Full

40 CFR 86.117-96 - Evaporative emission enclosure calibrations.

Science.gov (United States)

2010-07-01

... periodic determination of enclosure background emissions. Prior to its introduction into service, annually... procedure: (1) Carefully measure the internal length, width and height of the enclosure, accounting for... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Evaporative emission enclosure...

Feedstock to Tailpipe Initiative: Kansas Biofuels Production, Testing and Certification Laboratory

Energy Technology Data Exchange (ETDEWEB)

Stagg-Williams, Susan M. [Univ. of Kansas, Lawrence, KS (United States). Dept. of Chemical and Petroleum Engineering; Depcik, Chris [Univ. of Kansas, Lawrence, KS (United States). Dept. of Chemical and Petroleum Engineering; Sturm, Belinda [Univ. of Kansas, Lawrence, KS (United States). Dept. of Chemical and Petroleum Engineering

2013-12-31

The primary task of this grant was to establish an ASTM testing facility for biodiesel and ethanol and to use this facility to develop methods to predict fuel characteristics based on feedstock composition and feedstock cultivation. In addition to characterizing fuel properties, this grant allowed for the purchase and installation of a Fourier Transform Infrared Spectroscopy (FTIR) emissions analyzer that will provide an analysis of the emissions leaving the engine in order to meet EPA regulations. This FTIR system is combined with an Alternating Current (AC) dynamometer that allows the engine to follow Environmental Protection Agency (EPA) Federal Test Procedure (FTP) cycles. A secondary task was to investigate cultivating algae utilizing wastewater and top-down ecological control and subsequent harvesting using coagulation and dissolved air flotation. Lipid extraction utilizing environmentally-friendly and cost-effective solvents, with and without cell-disruption pretreatment was also explored. Significant work on the hydrothermal liquefaction of wastewater cultivated algae was conducted.

Central stars of planetary nebulae. II. New OB-type and emission-line stars

Science.gov (United States)

Weidmann, W. A.; Gamen, R.

2011-07-01

Context. There are more than 3000 confirmed and probably known Galactic planetary nebulae (PNe), but central star spectroscopic information is available for only 13% of them. Aims: We have undertaken a spectroscopic survey of the central stars in PNe to identify their spectral types. Methods: We performed spectroscopic observations at low resolution with the 2-m telescope at CASLEO, Argentina. Results: We present the spectra of 46 central stars of PNe, most of them are OB-type and emission-line stars. Based on data collected at the Complejo Astronómico El Leoncito (CASLEO), which is operated under agreement between the Consejo Nacional de Investigaciones Científicas y Técnicas de la República Argentina y Universidades Nacionales de La Plata, Córdoba y San Juan, Argentina.The reduced spectra (FITS files) are available in electronic form at the CDS via anonymous ftp to cdsarc.u-strasbg.fr (130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/531/A172

On exhaust emissions from petrol-fuelled passenger cars at low ambient temperatures

Energy Technology Data Exchange (ETDEWEB)

Laurikko, J. [VTT Energy, Espoo (Finland). Energy Use

1998-11-01

The study at hand deals with regulated and unregulated exhaust emissions from petrol-fuelled cars at low ambient temperatures with present-day or near-future exhaust after treatment systems. The subject has been investigated at VTT over a decade and this report compiles data from various sub-studies carried out between the years 1993 - 1997. Each one of them viewed different aspects of the phenomenon, like determining the low-temperature response of today`s new cars employing three-way catalytic converters or assessing the long-term durability and the influence of vehicle mileage upon the low-temperature emissions performance. Within these studies, together more than 120 cars of model years from 1990 to 1997 have been tested. Most of them were normal, in-service vehicles with total mileages differing between only a few thousand kilometres for new cars up to 80,000 km or even more for the in-use vehicles. Both the US FTP75 and the European test cycle have been employed, and the ambient temperatures ranged from the baseline (+22 deg C) down to +- O deg C, -7 deg C and in some cases even to -20 deg C. The studies attested that new cars having today`s advanced emissions control systems produced fairly low levels of emissions when tested in conditions designated in the regulations that are the basis of the current new-vehicle certification. However, this performance was not necessarily attained at ambient temperatures that were below the normative range. Fairly widespread response was recorded, and cars having almost equal emissions output at baseline could produce largely deviating outcomes in low-temperature conditions. On average, CO and HC emissions increased by a factor of five to 10, depending on the ambient temperature and vehicle type. However, emissions of NO{sub x} were largely unaffected. Apart from these regulated emissions, many unregulated species were also determined, either by using traditional sampling and chromatography methods or on-line, employing

Expertise, following the 5.7.1977 decree: assessment of the procedure; Expertise, arrete du 5.7.77 - bilan de la procedure

Energy Technology Data Exchange (ETDEWEB)

Maillard, M. [Ministere de l`Industrie, des Postes et Telecommunications, 75 - Paris (France)

1996-12-31

The French Government decree concerning the periodical inspection and extensive examination procedure for plants and buildings where thermal energy is consumed, is presented. The inspection procedure is intended to control the thermal and electrical equipment, the regulation systems, the pollutant emission control systems and the waste heat recovery systems. Design recommendations, fuel substitution, pollution abatement, waste heat up-grading, etc. may be proposed by the expert

Procedures for identifying reasonably available control technology for stationary sources of PM-10. Final report

International Nuclear Information System (INIS)

Fitzpatrick, M.J.; Ellefson, R.

1992-09-01

The guidance document sets forth procedures and identifies sources of information that will assist State and local air pollution control agencies in determining Reasonably Available Control Technology (RACT) for PM-10 (particulate matter having a nominal aerometric diameter of 10 microns or less) emission from existing stationary sources on a case-by-case basis. It provides an annotated bibliography of documents to aid in identifying the activities that cause PM-10 emissions as well as applicable air pollution control measures and their effectiveness in reducing emissions. The most stringent state total particulate matter (PM) emission limits are identified for several categories of PM-10 sources and compared to available emission test data. Finally, guidance is provided on procedures for estimating total capital investment and total annual cost of the control measures which are generally used to control PM-10 emissions

Analysis of non-regulated vehicular emissions by extractive FTIR spectrometry: tests on a hybrid car in Mexico City

Science.gov (United States)

Reyes, F.; Grutter, M.; Jazcilevich, A.; González-Oropeza, R.

2006-07-01

A methodology to acquire valuable information on the chemical composition and evolution of vehicular emissions is presented. The analysis of the gases is performed by passing a constant flow of a sample gas from the tail-pipe into a 10 L multi-pass cell. The absorption spectra within the cell are obtained using an FTIR spectrometer at 0.5 cm-1 resolution along a 13.1 m optical path. Additionally, the total flow from the exhaust is continuously measured from a differential pressure sensor on a Pitot tube installed at the exit of the exhaust. This configuration aims to obtain a good speciation capability by coadding spectra during 30 s and reporting the emission (in g/km) of key and non-regulated pollutants, such as CO2, CO, NO, SO2, NH3, HCHO, NMHC, during predetermined driving routines. The advantages and disadvantages of increasing the acquisition frequency, as well as the effect of other parameters such as spectral resolution, cell volume and flow rate, are discussed. With the aim of testing and evaluating the proposed technique, experiments were performed on a dynamometer running FTP-75 and typical driving cycles of the Mexico City Metropolitan Area (MCMA) on a Toyota Prius hybrid vehicle. This car is an example of recent automotive technology to reach the market dedicated to reduce emissions and therefore pressing the need of low detection techniques. This study shows the potential of the proposed technique to measure and report in real time the emissions of a large variety of pollutants, even from a super ultra-low emission vehicle (SULEV). The emissions of HC's, NOx, CO and CO2 obtained here are similar to experiments performed in other locations with the same vehicle model. Some differences suggest that an inefficient combustion process and type of gasoline used in the MCMA may be partly responsible for lower CO2 and higher CO and NO emission factors. Also, a fast reduction of NO emission to very low values is observed after cold ignition, giving rise to

Simulation of Energy Consumption and Emissions from Rail Traffic

DEFF Research Database (Denmark)

Lindgreen, Erik Bjørn Grønning; Sorenson, Spencer C

. The calculation procedure is evaluated with respect to resolution of operation conditions, and then evaluated by comparison with experimental data for a variety of passenger and goods trains. The results indicate that the energy consumption from modeling approach is valid to better that 10% for known operating...... characteristics. Emissions are calculated from the energy consumption using average fuel based emissions factors and electrical production emissions factors....

40 CFR 86.1327-96 - Engine dynamometer test procedures; overview.

Science.gov (United States)

2010-07-01

... device, the exhaust pipe must be the same diameter as found in-use for at least 4 pipe diameters upstream... Exhaust Test Procedures § 86.1327-96 Engine dynamometer test procedures; overview. (a) The engine.... The exhaust emissions are diluted with ambient air and a continuous proportional sample is collected...

Procedure for measurement of anisotropy factor for neutron sources

International Nuclear Information System (INIS)

Creazolla, Prycylla Gomes

2017-01-01

Radioisotope neutron sources allow the production of reference fields for calibration of neutron detectors for radiation protection and analysis purposes. When the emission rate of these sources is isotropic, no correction is necessary. However, variations in source encapsulation and in the radioactive material concentration produce differences in its neutron emission rate, relative to the source axis, this effect is called anisotropy. In this study, is describe a procedure for measuring the anisotropy factor of neutron sources performed in the Laboratório de Metrologia de Neutrons (LN) using a Precision Long Counter (PLC) detector. A measurement procedure that takes into account the anisotropy factor of neutron sources contributes to solve some issues, particularly with respect to the high uncertainties associated with neutron dosimetry. Thus, a bibliographical review was carried out based on international standards and technical regulations specific to the area of neutron fields, and were later reproduced in practice by means of the procedure for measuring the anisotropy factor in neutron sources of the LN. The anisotropy factor is determined as a function of the angle of 90° in relation to the cylindrical axis of the source. This angle is more important due to its high use in measurements and also of its higher neutron emission rate if compared with other angles. (author)

Material Flow System Based on FTP in TV Station%基于FTP的电视台素材流转系统

Institute of Scientific and Technical Information of China (English)

许南山; 陈亮; 刘淑梅

2012-01-01

In the process of program production in TV station, the material flow mainly relies on simple file sharing. It is complicated and difficult to manage. To solve these problems,an FTP-based material flowing system has been proposed. According to the characteristics of working flow in TV station, special file organization and access management strategy are developed. In the automatic file packaging function, compatible interface has been provided to different file formats. Through the deployment, the feasibility and usability are verified.%当前常规的电视台节目制作过程中,素材文件流转依靠简单的文件共享方式,操作复杂,难以管理.针对这些问题,设计并实现了基于FTP的素材流转系统.根据电视台文件流转的特点,制定文件组织方式和访问管理策略:在文件自动打包功能中提供接口以兼容不同的文件格式;通过实际部署,验证了系统的可行性与易用性.

Government review of the countdown companies' 1991 acid gas emissions audits

Energy Technology Data Exchange (ETDEWEB)

1993-08-01

An acid gas emissions verification program was implemented in Ontario in 1990 as part of a program for regulating emissions that are precursors to acid rain. The verification program applied to four companies, three in the metals industry and one electric utility. These emitters were required to limit annual SO[sub 2] and nitrogen oxides emissions to specified levels in stages according to a set schedule. The four companies were required to prepare and submit sulfur mass balance procedures manuals, determine the overall uncertainty of their respective annual emissions, and engage an independent auditor to develop an audit protocol manual and conduct audits of the reported emissions. For Ontario Hydro, the auditor was also required to evaluate the continuous flue gas monitoring systems at the utility's fossil-fuel power plants. The auditors confirmed that the metallurgical companies' reported emissions were within the required limits. For Ontario Hydro, the audit also confirmed that both SO[sub 2] and nitrogen oxide emissions were within the limits specified for 1991. The auditor also indicated that there were no major discrepancies with the procedures manuals that affected the calculated SO[sub 2] and nitrogen oxides emissions. 6 refs., 2 tabs.

Flame emission, atomic absorption and fluorescence spectrometry

International Nuclear Information System (INIS)

Horlick, G.

1980-01-01

Six hundred and thirty references are cited in this review. The information in the review is divided into 12 major areas: books, reviews, and bibliographies; fundamental studies in flames; developments in instrumentation; measurement techniques and procedure; flame emission spectrometry; flame atomic absorption spectrometry; flame molecular absorption spectrometry; electrothermal atomization atomic absorption spectroscopy; hydride generation techniques; graphite furnace atomic emission spectrometry; atomic fluorescence spectrometry; and analytical comparisons

Mathematical Model of the Emissions of a selected vehicle

Directory of Open Access Journals (Sweden)

Matušů Radim

2014-10-01

Full Text Available The article addresses the quantification of exhaust emissions from gasoline engines during transient operation. The main targeted emissions are carbon monoxide and carbon dioxide. The result is a mathematical model describing the production of individual emissions components in all modes (static and dynamic. It also describes the procedure for the determination of emissions from the engine’s operating parameters. The result is compared with other possible methods of measuring emissions. The methodology is validated using the data from an on-road measurement. The mathematical model was created on the first route and validated on the second route.

Catalyzed Diesel Particulate Filter Performance in a Light-Duty Vehicle

International Nuclear Information System (INIS)

Sluder, C.S.

2001-01-01

Light-duty chassis dynamometer driving cycle tests were conducted on a Mercedes A170 diesel vehicle with various sulfur-level fuels and exhaust emission control systems. Triplicate runs of a modified light-duty federal test procedure (FTP), US06 cycle, and SCO3 cycle were conducted with each exhaust configuration and fuel. Ultra-low sulfur (3-ppm) diesel fuel was doped to 30- and 150-ppm sulfur so that all other fuel properties remained the same. The fuels used in these experiments met the specifications of the fuels from the DECSE (Diesel Emission Control Sulfur Effects) program. Although the Mercedes A170 vehicle is not available in the US, its emissions in the as tested condition fell within the U.S. Tier 1 full useful life standards with the OEM catalysts installed. Tests with the OEM catalysts removed showed that the OEM catalysts reduced PM emissions from the engine-out condition by 30-40% but had negligible effects on NOx emissions. Fuel sulfur level had very little effect on th e OEM catalyst performance. A prototype catalyzed diesel particulate filter (CDPF) mounted in an underfloor configuration reduced particulate matter emissions by more than 90% compared to the factory emissions control system. The results show that the CDPF did not promote any significant amounts of SO(sub 2)-to-sulfate conversion during these light-duty drive cycles

40 CFR 205.57-4 - Testing procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Testing procedures. 205.57-4 Section 205.57-4 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Medium and Heavy Trucks § 205.57-4 Testing...

Pre-service Acoustic Emission Testing for Metal Pressure Vessel

International Nuclear Information System (INIS)

Lee, Jong O; Yoon, Woon Ha; Lee, Tae Hee; Lee, Jong Kyu

2003-01-01

The field application of acoustic emission(AE) testing for brand-new metal pressure vessel were performed. We will introduce the test procedure for acoustic emission test such as instrument check distance between sensors, sensor location, whole system calibration, pressurization sequence, noise reduction and evaluation. The data of acoustic emission test contain many noise signal, these noise can be reduced by time filtering which based on the description of observation during AE test

Suggested guidelines for gas emission monitoring at danish landfills

DEFF Research Database (Denmark)

Kjeldsen, Peter; Scheutz, Charlotte

2015-01-01

Landfill gas is produced on waste disposal sites receiving organic waste resulting in emission of methane. Regulation requires that the landfill gas is managed in order to reduce emissions, but very few suggestions exist to how the landfill gas management activities are monitored, what requirements...... to the ability of the landfill gas management to reduce the emission should be set up, and how criteria are developed for when the monitoring activities can be terminated. Monitoring procedures are suggested centred on a robust method for measuring the total methane emission from the site, and quantitative...

Delay of Gratification, Delay Discounting and their Associations with Age, Episodic Future Thinking, and Future Time Perspective.

Science.gov (United States)

Göllner, Lars M; Ballhausen, Nicola; Kliegel, Matthias; Forstmeier, Simon

2017-01-01

The delay of gratification (DoG) in children is widely investigated with an experimental procedure originally called the "marshmallow test," whereas the studies on self-regulation (SR) in adolescents and adults usually use self-report questionnaires. Delay discounting (DD) measures simplify the DoG procedure and focus on monetary rewards. The aim of this study was to investigate age differences in DoG and DD from childhood to old age using a test that is suitable for both children and adults. Furthermore, investigations were conducted on the association between DoG/DD and two future orientation constructs [future time perspective (FTP) and episodic future thinking (EFT)] as well as age differences in these constructs. Participants from five age groups (9-14, 18-25, 35-55, 65-80, 80+) participated in the study ( N = 96). While we found no age difference for DoG, DD was the lowest [i.e., self-control (SC) was the highest] in young/middle adults; however, it was the highest (i.e., SC was the lowest) in children and old/oldest adults. Furthermore, we found significant age differences for DD and FTP. As predicted, there were strong correlations between DoG and FTP and between DD and FTP, but not between DoG/DD and EFT. These results indicate that age differences in SR vary across the measures used. Individuals who generally think and act in a future-oriented manner have a stronger ability to delay gratification.

GHG emission estimates for road transport in national GHG inventories

NARCIS (Netherlands)

Pulles, M.P.J.; Yang, H.

2011-01-01

The annual reporting procedures of the United Nations Framework Convention on Climate Change (UNFCCC) have now produced greenhouse gas (GHG) emission inventories from 40 so-called Annex I countries for 18 years. This article analyses a subset of these data: emissions from road transport. The article

Embodied greenhouse gas emission by Macao

International Nuclear Information System (INIS)

Li, J.S.; Chen, G.Q.; Lai, T.M.; Ahmad, B.; Chen, Z.M.; Shao, L.; Ji, Xi

2013-01-01

Comprehensive inventory of cities' greenhouse gas emissions (GHG) is the basis for cities to make appropriate mitigation plans. However, previous studies on cities' GHG emissions consider emissions occurring within the city boundary (Scope 1) and out of boundary electricity emissions (Scope 2), but neglect indirect emissions associated with commodities consumed by cities (Scope 3), resulting in emission leakage. To cope with this problem, a systematic accounting covering all 3 scopes is presented in a case study of Macao for the years 2005–2009, based on the latest embodied emission intensity databases for China and for the world. The results show that total emissions are dominated by indirect emissions mainly embodied in imports, which is 3–4 times direct emissions during the period concerned. It is verified that accounting under Scopes 1 and 2 cannot capture the full picture of cities' emissions, especially cities like Macao which are dominated by service industry and inevitably sustained by massive materials and services from other regions. Our study suggests that Macao should adjust its current GHG mitigation policies which consider only its emissions occurring within its border, as Macao is a net GHG emissions importer. This work is the first assessment of Macao's embodied GHG emissions. - Highlights: • A systematic accounting procedure is presented to inventory a city's GHG emissions. • A comprehensive review of GHG emissions is performed for Macao. • Indirect GHG emissions dominate Macao's embodied GHG emissions. • Macao induced large amount of GHG emissions in other regions through trade. • The variation in GHG emission structure against socio-economic changes is revealed

LAT FTP Data

Data.gov (United States)

National Aeronautics and Space Administration — Fermi is a powerful space observatory that will open a wide window on the universe. Gamma rays are the highest-energy form of light, and the gamma-ray sky is...

CDAWeb FTP Site

Data.gov (United States)

National Aeronautics and Space Administration — The CDAWeb data service (at http://cdaweb.gsfc.nasa.gov) offers graphic, listing, subsetting and data computation services for a continuously increasing database of...

Development of the methodology of exhaust emissions measurement under RDE (Real Driving Emissions) conditions for non-road mobile machinery (NRMM) vehicles

Science.gov (United States)

Merkisz, J.; Lijewski, P.; Fuc, P.; Siedlecki, M.; Ziolkowski, A.

2016-09-01

The paper analyzes the exhaust emissions from farm vehicles based on research performed under field conditions (RDE) according to the NTE procedure. This analysis has shown that it is hard to meet the NTE requirements under field conditions (engine operation in the NTE zone for at least 30 seconds). Due to a very high variability of the engine conditions, the share of a valid number of NTE windows in the field test is small throughout the entire test. For this reason, a modification of the measurement and exhaust emissions calculation methodology has been proposed for farm vehicles of the NRMM group. A test has been developed composed of the following phases: trip to the operation site (paved roads) and field operations (including u-turns and maneuvering). The range of the operation time share in individual test phases has been determined. A change in the method of calculating the real exhaust emissions has also been implemented in relation to the NTE procedure.

Membrane-Based Air Composition Control for Light-Duty Diesel Vehicles: A Benefit and Cost Assessment; FINAL

International Nuclear Information System (INIS)

K. Stork; R. Poola

1998-01-01

This report presents the methodologies and results of a study conducted by Argonne National Laboratory (Argonne) to assess the benefits and costs of several membrane-based technologies. The technologies evaluated will be used in automotive emissions-control and performance-enhancement systems incorporated into light-duty diesel vehicle engines. Such engines are among the technologies that are being considered to power vehicles developed under the government-industry Partnership for a New Generation of Vehicles (PNGV). Emissions of nitrogen oxides (NO(sub x)) from diesel engines have long been considered a barrier to use of diesels in urban areas. Recently, particulate matter (PM) emissions have also become an area of increased concern because of new regulations regarding emissions of particulate matter measuring 2.5 micrometers or less (PM(sub 2.5)). Particulates are of special concern for diesel engines in the PNGV program; the program has a research goal of 0.01 gram per mile (g/mi) of particulate matter emissions under the Federal Test Procedure (FTP) cycle. This extremely low level (one-fourth the level of the Tier II standard) could threaten the viability of using diesel engines as stand-alone powerplants or in hybrid-electric vehicles. The techniques analyzed in this study can reduce NO(sub x) and particulate emissions and even increase the power density of the diesel engines used in light-duty diesel vehicles

Performance audit procedures for opacity monitors

International Nuclear Information System (INIS)

Plaisance, S.J.; Peeler, J.W.

1987-04-01

This manual contains monitor-specific performance audit procedures and data forms for use in conducting audits of installed opacity continuous emission monitoring systems (CEMS). General auditing procedures and acceptance limits for various audit criteria are discussed. Practical considerations and common problems encountered in conducting audits are delineated, and recommendations are included to optimize the successful completion of performance audits. Performance audit procedures and field-data forms were developed for six common opacity CEMS: (1) Lear Siegler, Inc. Model RM-41; (2) Lear Siegler, Inc. Model RM-4; (3) Dynatron Model 1100; (4) Thermo Electron, Inc. Model 400; (5) Thermo Electron, Inc. Model 1000A; and (6) Enviroplan Model D-R280 AV. Generic audit procedures are included for use in evaluating opacity CEMS with multiple transmissometers and combiner devices. In addition, several approaches for evaluating the zero-alignment or clear-path zero response are described. The zero-alignment procedures are included since the factor is fundamental to the accuracy of opacity monitoring data, even though the zero-alignment checks cannot usually be conducted during a performance audit

Automotive emission standards. (Latest citations from Pollution Abstracts). Published Search

International Nuclear Information System (INIS)

1993-07-01

The bibliography contains citations concerning emission standards and air quality standards applied to automobile emissions. Included are federal and state regulations and policies regarding these emission standards. Techniques to meet emission standards are also addressed, involving fuel injection, catalysts, alternate engines, and automotive fuel refinery operations. Studies concerning implementation of automobile emission standards explore economic and environmental effects, testing and inspection procedures, and the automobile industry point of view. Most of the citations refer to gasoline engines, but a few pertain to diesel and other fuels. (Contains 250 citations and includes a subject term index and title list.)

Black carbon emissions in gasoline vehicle exhaust: a measurement and instrument comparison.

Science.gov (United States)

Kamboures, Michael A; Hu, Shishan; Yu, Yong; Sandoval, Julia; Rieger, Paul; Huang, Shiou-Mei; Zhang, Sherry; Dzhema, Inna; Huo, Darey; Ayala, Alberto; Chang, M C Oliver

2013-08-01

A pilot study was conducted to evaluate the performance and agreement of several commercially available black carbon (BC) measurement instruments, when applied to the quantification of BC in light-duty vehicle (LDV) exhaust. Samples from six vehicles, three fuels, and three driving cycles were used. The pilot study included determinations of the method detection limit (MDL) and repeatability. With respect to the MDL, the real-time instruments outperformed the time-integrated instruments, with MDL = 0.12 mg/mi for the AE51 Aethalometer, and 0.15 mg/mi for the Micro Soot Sensor (MSS), versus 0.38 mg/mi for the IMPROVE_A thermal/ optical method, and 0.35 mg/mi for the OT21_T Optical Transmissometer. The real-time instruments had repeatability values ranging from 30% to 35%, which are somewhat better than those of the time-integrated instruments (40-41%). These results suggest that, despite being less resource intensive, real-time methods can be equivalent or superior to time-integrated methods in terms of sensitivity and repeatability. BC mass data, from the photoacoustic and light attenuation instruments, were compared against same-test EC data, determined using the IMPROVE_A method. The MSS BC data was well correlated with EC, with R2 = 0.85 for the composite results and R2 = 0.86 for the phase-by-phase (PBP) results. The correlation of BC, by the AE51, AE22, and OT21_T with EC was moderate to weak. The weaker correlation was driven by the inclusion of US06 test data in the linear regression analysis. We hypothesize that test-cycle-dependent BC:EC ratios are due to the different physicochemical properties of particulate matter (PM) in US06 and Federal Test Procedure (FTP) tests. Correlation amongst the real-time MSS, PASS-1, AE51, and AE22 instruments was excellent (R2 = 0.83-0.95), below 1 mg/mi levels. In the process of investigating these BC instruments, we learned that BC emissions at sub-1 mg/mi levels can be measured and are achievable by current

SPECIFIC EMISSIONS FROM BIOMASS COMBUSTION

Directory of Open Access Journals (Sweden)

Pavel Skopec

2014-02-01

Full Text Available This paper deals with determining the specific emissions from the combustion of two kinds of biomass fuels in a small-scale boiler. The tested fuels were pellets made of wood and pellets made of rape plant straw. In order to evaluate the specific emissions, several combustion experiments were carried out using a commercial 25 kW pellet-fired boiler. The specific emissions of CO, SO2 and NOx were evaluated in relation to a unit of burned fuel, a unit of calorific value and a unit of produced heat. The specific emissions were compared with some data acquired from the reference literature, with relatively different results. The differences depend mainly on the procedure used for determining the values, and references provide no information about this. Although some of our experimental results may fit with one of the reference sources, they do not fit with the other. The reliability of the references is therefore disputable.

40 CFR Appendix I to Subparts D and E - Motorcycle Noise Emission Test Procedures [Note

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Motorcycle Noise Emission Test... (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Motorcycles Recall of noncomplying motorcycles; relabeling of mislabeled motorcycles. Appendix I to Subparts D and E—Motorcycle Noise...

Synthesis and preliminary evaluation of {sup 18}F-labeled 4-thia palmitate as a PET tracer of myocardial fatty acid oxidation

Energy Technology Data Exchange (ETDEWEB)

DeGrado, Timothy R. E-mail: trd@petsparc.mc.duke.edu; Wang Shuyan; Holden, James E.; Nickles, R. Jerome; Taylor, Michael; Stone, Charles K

2000-04-01

Interest remains strong for the development of a noninvasive technique for assessment of regional fatty acid oxidation rate in the myocardium. {sup 18}F-labeled 4-thia palmitate (FTP, 16-[{sup 18}F]fluoro-4-thia-hexadecanoic acid) has been synthesized and preliminarily evaluated as a metabolically trapped probe of myocardial fatty acid oxidation for positron emission tomography (PET). The radiotracer is synthesized by Kryptofix 2.2.2/K{sub 2}CO{sub 3} assisted nucleophilic radiofluorination of an iodo-ester precursor, followed by alkaline hydrolysis and by purification by reverse phase high performance liquid chromatography. Biodistribution studies in rats showed high uptake and long retention of FTP in heart, liver, and kidneys consistent with relatively high fatty acid oxidation rates in these tissues. Inhibition of carnitine palmitoyl-transferase-I caused an 80% reduction in myocardial uptake, suggesting the dependence of trapping on the transport of tracer into the mitochondrion. Experiments with perfused rat hearts showed that the estimates of the fractional metabolic trapping rate (FR) of FTP tracked inhibition of oxidation rate of palmitate with hypoxia, whereas the FR of the 6-thia analog 17-[{sup 18}F]fluoro-6-thia-heptadecanoic acid was insensitive to hypoxia. In vivo defluorination of FTP in the rat was evidenced by bone uptake of radioactivity. A PET imaging study with FTP in normal swine showed excellent myocardial images, prolonged myocardial retention, and no bone uptake of radioactivity up to 3 h, the last finding suggesting a species dependence for defluorination of the omega-labeled fatty acid. The results support further investigation of FTP as a potential PET tracer for assessing regional fatty acid oxidation rate in the human myocardium.

Synthesis and preliminary evaluation of 18F-labeled 4-thia palmitate as a PET tracer of myocardial fatty acid oxidation

International Nuclear Information System (INIS)

DeGrado, Timothy R.; Wang Shuyan; Holden, James E.; Nickles, R. Jerome; Taylor, Michael; Stone, Charles K.

2000-01-01

Interest remains strong for the development of a noninvasive technique for assessment of regional fatty acid oxidation rate in the myocardium. 18 F-labeled 4-thia palmitate (FTP, 16-[ 18 F]fluoro-4-thia-hexadecanoic acid) has been synthesized and preliminarily evaluated as a metabolically trapped probe of myocardial fatty acid oxidation for positron emission tomography (PET). The radiotracer is synthesized by Kryptofix 2.2.2/K 2 CO 3 assisted nucleophilic radiofluorination of an iodo-ester precursor, followed by alkaline hydrolysis and by purification by reverse phase high performance liquid chromatography. Biodistribution studies in rats showed high uptake and long retention of FTP in heart, liver, and kidneys consistent with relatively high fatty acid oxidation rates in these tissues. Inhibition of carnitine palmitoyl-transferase-I caused an 80% reduction in myocardial uptake, suggesting the dependence of trapping on the transport of tracer into the mitochondrion. Experiments with perfused rat hearts showed that the estimates of the fractional metabolic trapping rate (FR) of FTP tracked inhibition of oxidation rate of palmitate with hypoxia, whereas the FR of the 6-thia analog 17-[ 18 F]fluoro-6-thia-heptadecanoic acid was insensitive to hypoxia. In vivo defluorination of FTP in the rat was evidenced by bone uptake of radioactivity. A PET imaging study with FTP in normal swine showed excellent myocardial images, prolonged myocardial retention, and no bone uptake of radioactivity up to 3 h, the last finding suggesting a species dependence for defluorination of the omega-labeled fatty acid. The results support further investigation of FTP as a potential PET tracer for assessing regional fatty acid oxidation rate in the human myocardium

40 CFR 240.205-2 - Recommended procedures: Design.

Science.gov (United States)

2010-07-01

... air pollution control technology. (b) All emissions, including dust from vents, should be controlled. ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Recommended procedures: Design. 240.205-2 Section 240.205-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID...

40 CFR 63.1565 - What are my requirements for organic HAP emissions from catalytic cracking units?

Science.gov (United States)

2010-07-01

... HAP emissions from catalytic cracking units? 63.1565 Section 63.1565 Protection of Environment... are my requirements for organic HAP emissions from catalytic cracking units? (a) What emission... according to the procedures in the plan. (4) The emission limitations and operating limits for organic HAP...

1983 EML Procedures Manual. 26th Edition

International Nuclear Information System (INIS)

Volchok, H.L.; de Planque, G.

1983-01-01

This document consists of page and section changes to the following HASL-300 procedures: fallout collection methods, radiochemical 90 Sr, atomic absorption-emission spectrophotometry of trace metals, precipitation and lake water samples, anions by ion chromatography, polynuclear aromatic hydrocarbons in sediments, Mn in saline precipitation samples, and Pb in saline precipitation samples

Effect of hybrid system battery performance on determining CO2 emissions of hybrid electric vehicles in real-world conditions

International Nuclear Information System (INIS)

Alvarez, Robert; Schlienger, Peter; Weilenmann, Martin

2010-01-01

Hybrid electric vehicles (HEVs) can potentially reduce vehicle CO 2 emissions by using recuperated kinetic vehicle energy stored as electric energy in a hybrid system battery (HSB). HSB performance affects the individual net HEV CO 2 emissions for a given driving pattern, which is considered to be equivalent to unchanged net energy content in the HSB. The present study investigates the influence of HSB performance on the statutory correction procedure used to determine HEV CO 2 emissions in Europe based on chassis dynamometer measurements with three identical in-use examples of a full HEV model featuring different mileages. Statutory and real-world driving cycles and full electric vehicle operation modes have been considered. The main observation is that the selected HEVs can only use 67-80% of the charge provided to the HSB, which distorts the outcomes of the statutory correction procedure that does not consider such irreversibility. CO 2 emissions corrected according to this procedure underestimate the true net CO 2 emissions of one HEV by approximately 13% in real-world urban driving. The correct CO 2 emissions are only reproduced when considering the HSB performance in this driving pattern. The statutory procedure for correcting HEV CO 2 emissions should, therefore, be adapted.

Theory of X-ray absorption and emission spectra

International Nuclear Information System (INIS)

Mukoyama, Takeshi

2004-01-01

Theoretical studies on X-ray absorption and emission spectroscopy are discussed. Simple expressions for X-ray emission rate and X-ray absorption cross section are presented in the dipole approximation. Various atomic models to obtain realistic wave functions and theoretical calculations for X-ray absorption cross sections and X-ray emission rates are described. In the case of molecules and solids, molecular orbital methods for electronic structures and molecular wave functions are discussed. The emphasis is on the procedures to obtain the excited-state and continuum wave functions for molecules and to calculate the multi-center dipole matrix elements. The examples of the calculated X-ray absorption and emission spectra are shown and compared with the experimental results

A Simple But Comprehensive Methodology To Determine Gas-Phase Emissions Of Motor Vehicles With Extractive FTIR Spectrometry

Science.gov (United States)

Reyes, F. M.; Jaczilevich, A.; Grutter, M. A.; Huerta, M. A.; Rincón, P.; Rincón, R.; González, R.

2004-12-01

In this contribution, a methodology to acquire valuable information on the chemical composition and evolution of vehicular emissions is presented. With this innovative experimental set-up, it is possible to obtain real-time emissions of the combustion products without the need of dilution or sample collection. Key pollutants such as CO, CO2, H2CO, CH4, NO, N2O, NH3, SO2, CH3OH, acetylene, ethylene, ethane and total hydrocarbons, most of which are not regulated nor measured by current emissions control programs, can be accurately monitored with a single instrument. An FTIR spectrometer is used for the analysis of a constant flow of sample gas from the tail-pipe into a stainless-steel cylindrical cell of constant volume.(1) The cell is heated to 185 °C to avoid condensation, the pressure is kept constant and a multi-pass optical arrangement(2)is used to transmit the modulated infrared beam several times to improve the sensitivity. The total flow from the exhaust used for calculating the emission can be continuously determined from the differential pressure measurements from a "Pitot" tube calibrated against a hot-wire devise. This simple methodology is proposed for performing state-of-the-art evaluations on the emission behavior of new technologies, reformulated fuels and emission control devices. The results presented here were performed on a dynamometer running FTP-75 and driving cycles typical for Mexico City.(3,4) References 1. Grutter M. "Multi-Gas Analysis using FTIR Spectroscopy over Mexico City." Atmosfera 16, 1-16 (2003). 2. White J.U. "Long optical paths of large aperture. J. Opt. Soc. Am., 32, 285-288 (1942). 3. Santiago Cruz L. and P.I. Rincón. "Instrumentation of the Emission Control Laboratory at the Engineering School of the National Autonomous University of Mexico." Instrumentation and Development 4, 19-24, (2000). 4. González Oropeza R. and A. Galván Zacarías. "Desarrollo de ciclos de manejo característicos de la Ciudad de México." Memorias

Procedure for estimating permanent total enclosure costs

Energy Technology Data Exchange (ETDEWEB)

Lukey, M.E.; Prasad, C.; Toothman, D.A.; Kaplan, N.

1999-07-01

Industries that use add-on control devices must adequately capture emissions before delivering them to the control device. One way to capture emissions is to use permanent total enclosures (PTEs). By definition, an enclosure which meets the US Environmental Protection Agency's five-point criteria is a PTE and has a capture efficiency of 100%. Since costs play an important role in regulatory development, in selection of control equipment, and in control technology evaluations for permitting purposes, EPA has developed a Control Cost Manual for estimating costs of various items of control equipment. EPA's Manual does not contain any methodology for estimating PTE costs. In order to assist environmental regulators and potential users of PTEs, a methodology for estimating PTE costs was developed under contract with EPA, by Pacific Environmental Services, Inc. (PES) and is the subject of this paper. The methodology for estimating PTE costs follows the approach used for other control devices in the Manual. It includes procedures for sizing various components of a PTE and for estimating capital as well as annual costs. It contains verification procedures for demonstrating compliance with EPA's five-point criteria. In addition, procedures are included to determine compliance with Occupational Safety and Health Administration (OSHA) standards. Meeting these standards is an important factor in properly designing PTEs. The methodology is encoded in Microsoft Exel spreadsheets to facilitate cost estimation and PTE verification. Examples are given throughout the methodology development and in the spreadsheets to illustrate the PTE design, verification, and cost estimation procedures.

Procedure for estimating permanent total enclosure costs

Energy Technology Data Exchange (ETDEWEB)

Lukey, M E; Prasad, C; Toothman, D A; Kaplan, N

1999-07-01

Industries that use add-on control devices must adequately capture emissions before delivering them to the control device. One way to capture emissions is to use permanent total enclosures (PTEs). By definition, an enclosure which meets the US Environmental Protection Agency's five-point criteria is a PTE and has a capture efficiency of 100%. Since costs play an important role in regulatory development, in selection of control equipment, and in control technology evaluations for permitting purposes, EPA has developed a Control Cost Manual for estimating costs of various items of control equipment. EPA's Manual does not contain any methodology for estimating PTE costs. In order to assist environmental regulators and potential users of PTEs, a methodology for estimating PTE costs was developed under contract with EPA, by Pacific Environmental Services, Inc. (PES) and is the subject of this paper. The methodology for estimating PTE costs follows the approach used for other control devices in the Manual. It includes procedures for sizing various components of a PTE and for estimating capital as well as annual costs. It contains verification procedures for demonstrating compliance with EPA's five-point criteria. In addition, procedures are included to determine compliance with Occupational Safety and Health Administration (OSHA) standards. Meeting these standards is an important factor in properly designing PTEs. The methodology is encoded in Microsoft Exel spreadsheets to facilitate cost estimation and PTE verification. Examples are given throughout the methodology development and in the spreadsheets to illustrate the PTE design, verification, and cost estimation procedures.

On the mechanism of fission neutron emission

International Nuclear Information System (INIS)

Maerten, H.; Richter, D.; Seeliger, D.

1986-01-01

This review represents the present knowledge of the mechanism of prompt fission neutron emission. Starting with a brief fission process characterization related with neutron emission, possible emission mechanisms are discussed. It is emphasized that the experimental study of special mechanisms, i.e. scission neutron emission processes, requires a sufficiently correct description of emission probabilities on the base of the main mechanism, i.e. the evaporation from fully accelerated fragments. Adequate statistical-model approaches have to account for the complexity of nuclear fission reflected by an intricate fragment distribution. The present picture of scission neutron emission is not clarified neither experimentally nor theoretically. Deduced data are contradictory and depend on the used analysis procedures often involving rough discriptions of evaporated-neutron distributions. The contribution of two secondary mechanisms of fission neutron emission, i.e. the neutron evaporation during fragment acceleration and neutron emission due to the decay of 5 He after ternary fission, is estimated. We summarize the recent progress of the theoretical description of fission neutron spectra in the framework of statistical models considering the standard spectrum of 252 Cf(sf) neutrons especially. The main experimental basis for the study of fission neutron emission is the accurate measurement of emission probabilities as a function of emission energy and angle (at least) as well as fragment parameters (mass number ratio and kinetic energy). The present status is evaluated. (author)

Delay of Gratification, Delay Discounting and their Associations with Age, Episodic Future Thinking, and Future Time Perspective

Directory of Open Access Journals (Sweden)

Lars M. Göllner

2018-01-01

Full Text Available The delay of gratification (DoG in children is widely investigated with an experimental procedure originally called the “marshmallow test,” whereas the studies on self-regulation (SR in adolescents and adults usually use self-report questionnaires. Delay discounting (DD measures simplify the DoG procedure and focus on monetary rewards. The aim of this study was to investigate age differences in DoG and DD from childhood to old age using a test that is suitable for both children and adults. Furthermore, investigations were conducted on the association between DoG/DD and two future orientation constructs [future time perspective (FTP and episodic future thinking (EFT] as well as age differences in these constructs. Participants from five age groups (9–14, 18–25, 35–55, 65–80, 80+ participated in the study (N = 96. While we found no age difference for DoG, DD was the lowest [i.e., self-control (SC was the highest] in young/middle adults; however, it was the highest (i.e., SC was the lowest in children and old/oldest adults. Furthermore, we found significant age differences for DD and FTP. As predicted, there were strong correlations between DoG and FTP and between DD and FTP, but not between DoG/DD and EFT. These results indicate that age differences in SR vary across the measures used. Individuals who generally think and act in a future-oriented manner have a stronger ability to delay gratification.

National fossil fuels consumption: Estimates of CO2 emissions and thermic pollution

International Nuclear Information System (INIS)

Mariani, Mario; Casale, Francesco

1997-01-01

The study on the basis of the national energy consumption from 1988 to 1994, estimates CO 2 emission rates produced by the most relevant hydrocarbons involved in the technological combustion processes and assess the potential thermic impact on the environment. Two calculation procedures have been developed taking into account once emission factors and other emission indexes in order to verify the two estimates. Besides, the work determines the national trend of CO 2 emission with regard to the aim for the stabilization of carbon dioxide emissions at 1990 levels by 2000

Mapping the spatial distribution of global anthropogenic mercury atmospheric emission inventories

Science.gov (United States)

Wilson, Simon J.; Steenhuisen, Frits; Pacyna, Jozef M.; Pacyna, Elisabeth G.

This paper describes the procedures employed to spatially distribute global inventories of anthropogenic emissions of mercury to the atmosphere, prepared by Pacyna, E.G., Pacyna, J.M., Steenhuisen, F., Wilson, S. [2006. Global anthropogenic mercury emission inventory for 2000. Atmospheric Environment, this issue, doi:10.1016/j.atmosenv.2006.03.041], and briefly discusses the results of this work. A new spatially distributed global emission inventory for the (nominal) year 2000, and a revised version of the 1995 inventory are presented. Emissions estimates for total mercury and major species groups are distributed within latitude/longitude-based grids with a resolution of 1×1 and 0.5×0.5°. A key component in the spatial distribution procedure is the use of population distribution as a surrogate parameter to distribute emissions from sources that cannot be accurately geographically located. In this connection, new gridded population datasets were prepared, based on the CEISIN GPW3 datasets (CIESIN, 2004. Gridded Population of the World (GPW), Version 3. Center for International Earth Science Information Network (CIESIN), Columbia University and Centro Internacional de Agricultura Tropical (CIAT). GPW3 data are available at http://beta.sedac.ciesin.columbia.edu/gpw/index.jsp). The spatially distributed emissions inventories and population datasets prepared in the course of this work are available on the Internet at www.amap.no/Resources/HgEmissions/

Effect of hybrid system battery performance on determining CO{sub 2} emissions of hybrid electric vehicles in real-world conditions

Energy Technology Data Exchange (ETDEWEB)

Alvarez, Robert; Schlienger, Peter; Weilenmann, Martin [Empa, Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Internal Combustion Engines, Ueberlandstrasse 129, CH-8600 Duebendorf (Switzerland)

2010-11-15

Hybrid electric vehicles (HEVs) can potentially reduce vehicle CO{sub 2} emissions by using recuperated kinetic vehicle energy stored as electric energy in a hybrid system battery (HSB). HSB performance affects the individual net HEV CO{sub 2} emissions for a given driving pattern, which is considered to be equivalent to unchanged net energy content in the HSB. The present study investigates the influence of HSB performance on the statutory correction procedure used to determine HEV CO{sub 2} emissions in Europe based on chassis dynamometer measurements with three identical in-use examples of a full HEV model featuring different mileages. Statutory and real-world driving cycles and full electric vehicle operation modes have been considered. The main observation is that the selected HEVs can only use 67-80% of the charge provided to the HSB, which distorts the outcomes of the statutory correction procedure that does not consider such irreversibility. CO{sub 2} emissions corrected according to this procedure underestimate the true net CO{sub 2} emissions of one HEV by approximately 13% in real-world urban driving. The correct CO{sub 2} emissions are only reproduced when considering the HSB performance in this driving pattern. The statutory procedure for correcting HEV CO{sub 2} emissions should, therefore, be adapted. (author)

Sportswear textiles emissivity measurement: comparison of IR thermography and emissometry techniques

Science.gov (United States)

Bison, P.; Grinzato, E.; Libbra, A.; Muscio, A.

2012-06-01

Three sportswear textiles are compared, one normal and two 'special' with Ag+ ions and Carbon powder added, with different colors. The emissivity of the textiles has been measured to determine if it is increased in the 'special' textiles with respect to the normal one. The test implied some non-standard procedure due to the semitransparent nature of the textiles, in comparison with the normal procedure that is commonly used on opaque surfaces. The test is also carried out by a standard emissometry technique, based on a comparative approach with reference samples having known thermal emissivity. The results are compared and discussed.

Developing a Dust Emission Procedure for Central Asia

Directory of Open Access Journals (Sweden)

Longlei Li

2017-05-01

Full Text Available Airborne mineral dust is thought to have a significant influence on the climate through absorbing and scattering both shortwave and longwave radiations and affecting cloud microphysical processes. However, a knowledge of long-term dust emissions is limited from both temporal and spatial perspectives. Here, we have developed a quantitative climatology: the column-integrated mass of the dust aerosol loading in Central Asia by incorporating the dust module (DuMo into the Weather Research and Forecasting coupled with Chemistry (WRF-Chem model and accounting for regional climate and Land-Cover and Land-Use Changes for the 1950-2010 period in April. This data set is lowly to moderately correlated (0.22-0.48 with the satellite Aerosol Optical Depth in April of the 2000s and lowly correlated (0.02-0.11 with the Absorbing Aerosol Index in April of the 1980s, 1990s, and 2000s. The total dust loading is approximately 207.85 Mton per month in April during the recent decade (2000-2014 over dust source regions. Although only the month of April was simulated, results suggest that trends and magnitudes are captured well, using the WRF-Chem-DuMo.

Development and application of a mobile laboratory for measuring emissions from diesel engines. 1. Regulated gaseous emissions.

Science.gov (United States)

Cocker, David R; Shah, Sandip D; Johnson, Kent; Miller, J Wayne; Norbeck, Joseph M

2004-04-01

Information about in-use emissions from diesel engines remains a critical issue for inventory development and policy design. Toward that end, we have developed and verified the first mobile laboratory that measures on-road or real-world emissions from engines at the quality level specified in the U.S. Congress Code of Federal Regulations. This unique mobile laboratory provides information on integrated and modal regulated gaseous emission rates and integrated emission rates for speciated volatile and semivolatile organic compounds and particulate matter during real-world operation. Total emissions are captured and collected from the HDD vehicle that is pulling the mobile laboratory. While primarily intended to accumulate data from HDD vehicles, it may also be used to measure emission rates from stationary diesel sources such as back-up generators. This paper describes the development of the mobile laboratory, its measurement capabilities, and the verification process and provides the first data on total capture gaseous on-road emission measurements following the California Air Resources Board (ARB) 4-mode driving cycle, the hot urban dynamometer driving schedule (UDDS), the modified 5-mode cycle, and a 53.2-mi highway chase experiment. NOx mass emission rates (g mi(-1)) for the ARB 4-mode driving cycle, the hot UDDS driving cycle, and the chase experimentwerefoundto exceed current emission factor estimates for the engine type tested by approximately 50%. It was determined that congested traffic flow as well as "off-Federal Test Procedure cycle" emissions can lead to significant increases in per mile NOx emission rates for HDD vehicles.

Potential benefits of oxygen-enriched intake air in a vehicle powered by a spark-ignition engine

Science.gov (United States)

Ng, H. K.; Sekar, R. R.

1994-04-01

A production vehicle powered by a spark-ignition engine (3.1-L Chevrolet Lumina, model year 1990) was tested. The test used oxygen-enriched intake air containing 25 and 28% oxygen by volume to determine (1) if the vehicle would run without difficulties and (2) if emissions benefits would result. Standard Federal Test Procedure (FTP) emissions test cycles were run satisfactorily. Test results of catalytic converter-out emissions (emissions out of the converter) showed that both carbon monoxide and hydrocarbons were reduced significantly in all three phases of the emissions test cycle. Test results of engine-out emissions (emissions straight out of the engine, with the converter removed) showed that carbon monoxide was significantly reduced in the cold phase. All emission test results were compared with those for normal air (21% oxygen). The catalytic converter also had an improved carbon monoxide conversion efficiency under the oxygen-enriched-air conditions. Detailed results of hydrocarbon speciation indicated large reductions in 1,3-butadiene, formaldehyde, acetaldehyde, and benzene from the engine with the oxygen-enriched air. Catalytic converter-out ozone was reduced by 60% with 25%-oxygen-content air. Although NO(x) emissions increased significantly, both for engine-out and catalytic converter-out emissions, we anticipate that they can be ameliorated in the near future with new control technologies. The automotive industry currently is developing exhaust-gas control technologies for an oxidizing environment; these technologies should reduce NO(x) emissions more efficiently in vehicles that use oxygen-enriched intake air. On the basis of estimates made from current data, several production vehicles that had low NO(x) emissions could meet the 2004 Tier 2 emissions standards with 25%-oxygen-content air.

40 CFR Appendix A to Subpart T of... - Test of Solvent Cleaning Procedures

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Test of Solvent Cleaning Procedures A... CATEGORIES National Emission Standards for Halogenated Solvent Cleaning Pt. 63, Subpt. T, App. A Appendix A to Subpart T of Part 63—Test of Solvent Cleaning Procedures General Questions ___ 1. What is the...

Environmental Management Department Quality Assurance Project Plan for Radionuclide Emission Measurements Project for compliance with National Emission Standards for Hazardous Air Pollutants (NESHAP)

Energy Technology Data Exchange (ETDEWEB)

Poole, D A

1992-06-01

This Quality Assurance Project Plan (QAPP) satisfies the quality assurance (QA) requirements in 40 CFR Part 61, Method 114, for ensuring that the radionuclide air emission measurements from the Y-12 Plant are representative; of a known precision and accuracy; and include administrative controls to ensure prompt response when emission measurements indicate an increase over normal radionuclide emissions. The QAPP ensures the quality of the Y-12 Plant radionuclide emission measurements data from the continuous samplers, breakthrough monitors, and minor radionuclide release points. The plan specifies the procedures for the management of the activities affecting the quality of the data for the Y-12 Plant Environmental Management Department (EMD) within the Health, Safety, Environment, and Accountability Division (HSEA).

Environmental Management Department Quality Assurance Project Plan for Radionuclide Emission Measurements Project for compliance with National Emission Standards for Hazardous Air Pollutants (NESHAP)

International Nuclear Information System (INIS)

Poole, D.A.

1992-06-01

This Quality Assurance Project Plan (QAPP) satisfies the quality assurance (QA) requirements in 40 CFR Part 61, Method 114, for ensuring that the radionuclide air emission measurements from the Y-12 Plant are representative; of a known precision and accuracy; and include administrative controls to ensure prompt response when emission measurements indicate an increase over normal radionuclide emissions. The QAPP ensures the quality of the Y-12 Plant radionuclide emission measurements data from the continuous samplers, breakthrough monitors, and minor radionuclide release points. The plan specifies the procedures for the management of the activities affecting the quality of the data for the Y-12 Plant Environmental Management Department (EMD) within the Health, Safety, Environment, and Accountability Division (HSEA)

Emission of toxic air pollutants from biomass combustion

International Nuclear Information System (INIS)

Houck, J.E.; Barnett, S.G.; Roholt, R.B.; Rock, M.E.

1991-01-01

Combustion of biomass for power generation, home heating, process steam generation, and waste disposal constitutes a major source of air pollutants nationwide. Emissions from hog-fueled boilers, demolition wood-fired power plants, municipal waste incinerators, woodstoves, fireplaces, pellet stoves, agricultural burning, and forestry burning have been characterized for a variety of purposes. These have included risk assessment, permitting, emission inventory development, source profiling for receptor modeling, and control technology evaluations. From the results of the source characterization studies a compilation of emission factors for criteria and non-criteria pollutants are presented here. Key among these pollutants are polycyclic aromatic hydrocarbons, priority pollutant metals, carbon monoxide, sulfur dioxide, nitrous oxides, and PM 10 particles. The emission factors from the biomass combustion processes are compared and contrasted with other pollutant sources. In addition, sampling and analysis procedures most appropriate for characterizing emissions from the biomass combustion sources are also discussed

40 CFR 86.1823-01 - Durability demonstration procedures for exhaust emissions.

Science.gov (United States)

2010-07-01

...) Discussion of the manufacturer's in-use verification procedures including testing performed, vehicle... performed should also be documented in the manufacturer's submission. The in-use verification program shall...), the Alternate Service Accumulation Durability Program described in § 86.094-13(e) or the Standard Self...

National Emission Standards for Hazardous Air Pollutants submittal - 1997

International Nuclear Information System (INIS)

Townsend, Y.E.; Black, S.C.

1998-06-01

Each potential source of Nevada Test Site (NTS) emissions was characterized by one of the following methods: (1) monitoring methods and procedures previously developed at the NTS; (2) a yearly radionuclide inventory of the source, assuming that volatile radionuclide are released to the environment; (3) the measurement of tritiated water (as HTO or T 2 O) concentration in liquid effluents discharged to containment ponds and assuming all the effluent evaporates over the course of the year to become an air emission; or (4) using a combination of environmental measurements and CAP88-PC to calculate emissions. The emissions for National Emission Standards for Hazardous Air Pollutants (NESHAPs) reporting are listed. They are very conservative and are used in Section 3 to calculate the EDE to the maximally exposed individual offsite. Offsite environmental surveillance data, where available, are used to confirm that calculated emissions are, indeed, conservative

Regulated Emissions from Biodiesel Tested in Heavy-Duty Engines Meeting 2004 Emission Standards

Energy Technology Data Exchange (ETDEWEB)

McCormick, R. L.; Tennant, C. J.; Hayes, R. R.; Black, S.; Ireland, J.; McDaniel, T.; Williams, A.; Frailey, M.; Sharp, C. A.

2005-11-01

Biodiesel produced from soybean oil, canola oil, yellow grease, and beef tallow was tested in two heavy-duty engines. The biodiesels were tested neat and as 20% by volume blends with a 15 ppm sulfur petroleum-derived diesel fuel. The test engines were the following: 2002 Cummins ISB and 2003 DDC Series 60. Both engines met the 2004 U.S. emission standard of 2.5 g/bhp-h NO{sub x}+HC (3.35 g/kW-h) and utilized exhaust gas recirculation (EGR). All emission tests employed the heavy-duty transient procedure as specified in the U.S. Code of Federal Regulations. Reduction in PM emissions and increase in NO{sub x} emissions were observed for all biodiesels in all engines, confirming observations made in older engines. On average PM was reduced by 25% and NO{sub x} increased by 3% for the two engines tested for a variety of B20 blends. These changes are slightly larger in magnitude, but in the same range as observed in older engines. The cetane improver 2-ethyl hexyl nitrate was shown to have no measurable effect on NO{sub x} emissions from B20 in these engines, in contrast to observations reported for older engines. The effect of intake air humidity on NO{sub x} emissions from the Cummins ISB was quantified. The CFR NO{sub x}/humidity correction factor was shown to be valid for an engine equipped with EGR, operating at 1700 m above sea level, and operating on conventional or biodiesel.

40 CFR 93.122 - Procedures for determining regional transportation-related emissions.

Science.gov (United States)

2010-07-01

... of transit currently is anticipated to be a significant factor in satisfying transportation demand... in the latest conforming TIP) with design concept and scope adequate to determine its contribution to... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Procedures for determining regional...

Magnetic emission ranking of electrical appliances. A comprehensive market survey

International Nuclear Information System (INIS)

Leitgeb, N.; Cech, R.; Schroettner, J.; Lehofer, P.; Schmidpeter, U.; Rampetsreiter, M.

2008-01-01

Over the last decades emissions of magnetic fields from electric appliances have considerably changed. Based on a comprehensive market survey it could be shown that today magnetic emissions are usually characterised by complex frequency spectra while single-frequency emissions have become rare. Therefore, spectral assessment procedures play a critical role. Compared to frequency-weighted equivalent magnetic induction, rms values may underestimate emissions up to two orders of magnitudes. Therefore, rms measurements are not suitable and emission-ranking lists of devices need revision. Surface hot-spot measurements at nominal load conditions and 230 V/50 Hz supply involved 1146 new electrical devices of 166 different categories. High emissions were not rare. Magnetic emissions of devices of 73 different categories exceeded reference levels up to almost two orders of magnitudes above reference levels. Maximum values were higher than reported so far. Magnetic emissions were high enough to make even conformity with existing basic restrictions not self-evident. (authors)

Analysis of zirconium alloys using inductively-coupled plasma emission spectrometry

International Nuclear Information System (INIS)

White, G.F.; Pickford, C.J.

1982-06-01

As part of an interlaboratory collaborative exercise, certain trace and minor elements have been determined in a proposed zircaloy reference material using inductively-coupled plasma emission spectrometry. A dissolution procedure involving hydrochloric and hydrofluoric acids was used for determination of Hf, Cr, Fe and Sn. Data have also been obtained for Ni, Cu and Mn. Use of a high resolution monochromator in a scanning mode was found necessary for measurement of the emission intensities in order to resolve the spectral lines of interest from the intense and complex emission from the zirconium matrix. (author)

Positron emission tomography of the heart

International Nuclear Information System (INIS)

Budinger, T.F.; Yano, Y.; Moyer, B.R.; Mathis, C.A.; Ganz, E.; Huesman, R.H.; Derenzo, S.E.

1982-01-01

Positron emission tomography (PET) of the heart can measure blood perfusion, metabolism of fatty acids, metabolism of sugars, uptake of amino acids and can quantitate infarction volume. The principles which are basic to PET instrumentation and procedures for quantitative studies of the heart muscle with examples of measurements of myocardial flow and metabolism, are reviewed

Positron emission tomography of the heart

International Nuclear Information System (INIS)

Budinger, T.F.; Yano, Y.; Huesman, R.H.; Derenzo, S.E.; Moyer, B.R.; Mathis, C.A.; Ganz, E.; Knittel, B.

1983-01-01

Positron emission tomography (PET) of the heart can measure blood perfusion, metabolism of fatty acids, metabolism of sugars, uptake of amino acids and can quantitate infarction volume. The principles are reviewed which are basic to PET instrumentation and procedures for quantitative studies of human physiology with examples of measurements of myocardial flow and metabolism

A phase I study on stereotactic body radiotherapy of liver metastases based on functional treatment planning using positron emission tomography with 2-[(18)F]fluoro-2-deoxy-d-galactose

DEFF Research Database (Denmark)

Fode, Mette Marie; Bak-Fredslund, Kirstine; Petersen, Jørgen Baltzer

2017-01-01

BACKGROUND AND PURPOSE: The galactose analog 2-[18F]fluoro-2-deoxy-d-galactose (FDGal) is used for quantification of regional hepatic metabolic capacity by functional positron emission tomography computerized tomography (PET/CT). In the present study, FDGal PET/CT was used for functional treatment...... planning (FTP) of stereotactic body radiotherapy (SBRT) of liver metastases with the aim of minimizing radiation dose to the best functioning liver tissue. MATERIAL AND METHODS: Fourteen patients referred for SBRT had FDGal PET/CT performed before and one month after the treatment. The planning CT...... and the FDGal PET/CT images were deformable co-registered. RESULTS: A reduction in the mean dose of approximately 2 Gy to the best functioning sub-volumes was obtained. One patient developed grade 2 acute morbidity and no patients experienced grade 3 or higher acute morbidities. The regional hepatic metabolic...

Regulated and unregulated emissions from modern 2010 emissions-compliant heavy-duty on-highway diesel engines.

Science.gov (United States)

Khalek, Imad A; Blanks, Matthew G; Merritt, Patrick M; Zielinska, Barbara

2015-08-01

The U.S. Environmental Protection Agency (EPA) established strict regulations for highway diesel engine exhaust emissions of particulate matter (PM) and nitrogen oxides (NOx) to aid in meeting the National Ambient Air Quality Standards. The emission standards were phased in with stringent standards for 2007 model year (MY) heavy-duty engines (HDEs), and even more stringent NOX standards for 2010 and later model years. The Health Effects Institute, in cooperation with the Coordinating Research Council, funded by government and the private sector, designed and conducted a research program, the Advanced Collaborative Emission Study (ACES), with multiple objectives, including detailed characterization of the emissions from both 2007- and 2010-compliant engines. The results from emission testing of 2007-compliant engines have already been reported in a previous publication. This paper reports the emissions testing results for three heavy-duty 2010-compliant engines intended for on-highway use. These engines were equipped with an exhaust diesel oxidation catalyst (DOC), high-efficiency catalyzed diesel particle filter (DPF), urea-based selective catalytic reduction catalyst (SCR), and ammonia slip catalyst (AMOX), and were fueled with ultra-low-sulfur diesel fuel (~6.5 ppm sulfur). Average regulated and unregulated emissions of more than 780 chemical species were characterized in engine exhaust under transient engine operation using the Federal Test Procedure cycle and a 16-hr duty cycle representing a wide dynamic range of real-world engine operation. The 2010 engines' regulated emissions of PM, NOX, nonmethane hydrocarbons, and carbon monoxide were all well below the EPA 2010 emission standards. Moreover, the unregulated emissions of polycyclic aromatic hydrocarbons (PAHs), nitroPAHs, hopanes and steranes, alcohols and organic acids, alkanes, carbonyls, dioxins and furans, inorganic ions, metals and elements, elemental carbon, and particle number were substantially (90

F-18-fluorodeoxyglucose-positron emission tomography in colorectal cancer

International Nuclear Information System (INIS)

Joerg, L.; Langsteger, W.

2002-01-01

Whole-body positron emission tomography (PET) with the radiolabeled glucose analog F-18-fluorodeoxyglucose (F-18-FDG) is a sensitive diagnostic tool that images tumors based on increased uptake of glucose. Several recent publications have shown that F-18-fluorodeoxyglucose-positron emission tomography is more sensitive than computed-tomography (CT) in detecting colorectal cancer. In patients with increasing CEA (carcinoembryonic antigen) and no evidence of recurrent disease on CT F-18-fluorodeoxyglucose-positron emission tomography often detects recurrent cancer. In all, patient management seems to be changed in about 25 % of patients who undergo F-18-fluorodeoxyglucose-positron emission tomography in addition to standard staging procedure. Limited reports to date on both chemotherapy and radiotherapy support the role of F-18-fluorodeoxyglucose-positron emission tomography in assessing treatment response. Also regarding preoperative staging of primary colorectal cancer the literature is very limited. (author)

Implementación de un servidor FTP utilizando el modelo cliente/servidor mediante el uso de sockets en lenguaje c UNIX con el fin de mejorar los tiempos de respuesta en la red

Directory of Open Access Journals (Sweden)

Juan de Dios Murillo

2016-03-01

Full Text Available Este trabajo pretende evaluar la latencia en la transferencia de archivos utilizando un servidor FTP con un modelo cliente-servidor empleando una computadora con el sistema operativo Fedora para ejecutar el código del modelo cliente/servidor con sockets en lenguaje C UNIX, con el fin de simular un servidor que contiene archivos con diferentes formatos y tamaños, y medir la latencia de la transmisión al subir y descargar los archivos del servidor, usando diferentes tamaños de buffer. Con los resultados del retardo en la transmisión en los diferentes escenarios y al compararlos, se observa que entre mayor sea el tamaño del buffer es menor la latencia y conforme aumenta el tamaño del archivo la latencia aumenta,

40 CFR 1051.501 - What procedures must I use to test my vehicles or engines?

Science.gov (United States)

2010-07-01

... vehicles or engines? 1051.501 Section 1051.501 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Test Procedures § 1051.501 What procedures must I use to test my vehicles or engines? This section describes test...

Guidance document to the BC emission offsets regulation

International Nuclear Information System (INIS)

2010-11-01

British Columbia's (BC) emission offset regulations were established under the Greenhouse Gas Reduction Targets Act passed in 2007. Targets for greenhouse gas (GHG) emission reductions included a 6 percent reduction by 2012; an 18 percent reduction by 2016; a 33 percent reduction by 2020; and an 80 percent reduction by 2050. Carbon neutral agreements began in 2008, and covered emissions produced from government business travel and by provincial government ministries and agencies. This report presented a list of key recommendations developed by the Pacific Carbon Trust for use in future carbon offset projects. Recommendations included the use of correct emission factors when quantifying projected emission reductions from an offset project; the use of a robust data management system; and the use of evidence in supporting additionality arguments. The document outlined planning procedures for project baseline selection processes, protocol selections, and the identification of sources sinks and reservoirs. Issues related to quantification and measurements, emissions factors, and accuracy and uncertainty were also addressed. Validation, verification, and contracting options were also presented. 6 tabs., 3 figs.

Final Rule for Control of Air Pollution from Aircraft and Aircraft Engines: Emission Standards and Test Procedures

Science.gov (United States)

EPA is amending the existing emission standards for oxides of nitrogen (NOx) for new commercial aircraft engines. These standards are equivalent to the NOx emission standards of the United Nations International Civil Aviation Organization (ICAO).

National Emission Standards for Hazardous Air Pollutants submittal -- 1994

International Nuclear Information System (INIS)

Townsend, Y.E.; Black, S.C.

1995-06-01

This report focuses on air quality at the Nevada Test Site (NTS) for 1994. A general description of the effluent sources are presented. Each potential source of NTS emissions was characterized by one of the following: (1) by monitoring methods and procedures previously developed at NTS; (2) by a yearly radionuclide inventory of the source, assuming that volatile radionuclides are released to the environment; (3) by the measurement of tritiated water concentration in liquid effluents discharged to containment ponds and assuming all the effluent evaporates over the course of the year to become an air emission; or (4) by using a combination of environmental measurements and CAP88-PC to calculate emissions. Appendices A through J describe the methods used to determine the emissions from the sources. These National Emission Standards for Hazardous Air Pollutants (NESHAP) emissions are very conservative, are used to calculate the effective dose equivalent to the Maximally Exposed Individual offsite, and exceed, in some cases, those reported in DOE's Effluent Information System (EIS). The NESHAP's worst-case emissions that exceed the EIS reported emissions are noted. Offsite environmental surveillance data are used to confirm that calculated emissions are, indeed, conservative

77 FR 3223 - National Emissions Standards for Hazardous Air Pollutants: Mineral Wool Production and Wool...

Science.gov (United States)

2012-01-23

... Emission Standards for Hazardous Air Pollutants: Mineral Wool Production Risk and Technology Review..., Administrative practice and procedure, Air pollution control, Hazardous substances, Intergovernmental relations... National Emissions Standards for Hazardous Air Pollutants: Mineral Wool Production and Wool Fiberglass...

Emissions and targets of greenhouse gases not included in the Emission Trading System 2013-2020

Energy Technology Data Exchange (ETDEWEB)

Verdonk, M.

2011-06-15

This report evaluates the European Commission's (EC) proposal to calculate Member States' targets for emissions not included in the Emission Trading System (ETS) (as announced in the so-called Effort Sharing Decision). The calculation procedures and data sources proposed by the EC have been used for calculating non-ETS emission targets for the Netherlands, for the years from 2013 to 2020. In order to compare results, an alternative approach also was introduced and evaluated. In this approach more transparent data sources were used. Furthermore, the report updates the emission forecast of non-ETS emission levels in the Netherlands, for 2020, and evaluates the consequences of excluding uncertainties related to monitoring from the (updated) emission forecast. It is concluded that, for the Netherlands, the non-ETS emission caps as proposed by the EC would result in an emission cap of 105 Mt CO2 equivalent by 2020. This is higher than in the alternative approach, which would result in a cap of 103 Mt CO2 equivalents. The difference is explained by the different data sources that were used. A drawback of the data sources used in the EC proposal is the lack of transparency of part of the data, which resulted in an additional uncertainty as not all issues could be verified. However, other Member States may not have similar data sources available, in case the EC decides to adopt the alternative approach. The calculated emission caps are to be considered as estimates based on the most recent (but sometimes uncertain) statistics. The EC will determine the definite caps by the end of 2012. Based on a 2010 forecast, and including both an updated division of emissions into ETS and non-ETS emissions and a revised methodology for calculating nitrous oxide emissions, we estimate that non-ETS emissions in the Netherlands would be 104 Mt CO2 equivalents by 2020, with an uncertainty range of between 96 and 112 Mt CO2 equivalents. It is our conclusion that non-ETS emission

Velocity-dependent emission factors of benzene, toluene and C 2-benzenes of a passenger car equipped with and without a regulated 3-way catalyst

Science.gov (United States)

Heeb, Norbert V.; Forss, Anna-Maria; Bach, Christian; Mattrel, Peter

Time-resolved chemical ionization mass spectrometry (CI-MS) has been used to investigate the velocity-dependent emission factors for benzene, toluene, the C 2-benzenes (xylenes and ethyl benzene) and nitrogen monoxide of a gasoline-driven passenger car (1.4 l, model year 1995) driven with or without catalytic exhaust gas treatment. A set of seven different driving cycles - including the European Driving Cycle (EDC), the US Urban (FTP 75) and the Highway driving cycles - with a total driving time of 12,000 s have been studied. From the obtained emission data, two sets of 15,300 and 17,200 data points which represent transient driving in the velocity range of 0-150 km h -1 and in an acceleration window of -2-3 m s -2 were explored to gain velocity-dependent emission factors. The passenger car, equipped with a regulated rhodium-platinum based three-way catalyst, showed optimal conversion efficiency (>95%) for benzene in the velocity range of 60-120 km h -1. The conversion of benzene was reduced (speed and engine load (>130 km h -1). Whereas the conversion efficiency for the class of C 2-benzenes was reduced to 10%, no net conversion could be found for toluene and benzene when driven above 130 km h -1. In contrast, the benzene and toluene emissions exceeded those of the untreated exhaust gas in the velocity range of 130-150 km h -1 by 50-92% and by 10-34%, respectively. Thus, benzene and toluene were formed across the examined three-way catalyst if the engine is operated for an extended time in a fuel-rich mode (lambda<1).

Procedures for measurement of anisotropy factor of neutron sources

International Nuclear Information System (INIS)

Creazolla, P.G.; Camargo, A.; Astuto, A.; Silva, F.; Pereira, W.W.

2017-01-01

Radioisotope sources of neutrons allow the production of reference fields for calibration of neutron measurement devices for radioprotection and analysis purposes. When the emission rate of these sources is isotropic, no correction is necessary. However, variations in the source capsule material and variations in the concentration of the emitting material may produce differences in its neutron emission rate relative to the source axis, this effect is called anisotropy. A proposed procedure for measuring the anisotropy factor of the sources belonging to the IRD/LNMRI/LN Neutron Metrology Laboratory using a Precision Long Counter (PLC) detector will be presented

Verification of the Danish emission inventory data by national and international data comparisons

Energy Technology Data Exchange (ETDEWEB)

Fauser, P.; Thomsen, Marianne; Nielsen, Ole-Kenneth; Winther, M.; Gyldenkaerne, S.; Hoffmann, L.; Lyck, E.; Boll Illerup, J.

2007-08-15

Danish emission intensity values, activity values and implied emission factors for identified key source categories are compared with corresponding values for the EU-15 countries (excluding Luxemburg). The emission values for all countries are based on national greenhouse gas inventories for the years 1990 (base year), 1997 and 2003 provided by the UNFCCC. The comparison is based on a proposed verification procedure that is designed for identifying emission indicators and evaluating data consistency and reliability for the energy and industry sectors. For all sectors the method gives good possibility for checking emission levels and consistency in time trends. (au)

Compound list: doxorubicin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available doxorubicin DOX 00149 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/doxorubicin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vitro/doxorubicin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/...Liver/Single/doxorubicin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/...archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/doxorubicin.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.bios

Compound list: allopurinol [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available allopurinol APL 00028 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/allopurinol.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vitro/allopurinol.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/...Liver/Single/allopurinol.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/...archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/allopurinol.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.bios

Decision-making for acoustic emission data set

International Nuclear Information System (INIS)

Pellionisz, P.

1992-12-01

Acoustic emission techniques are widely applied in proof tests of pressure vessels. Correct interpretation of experimental data is of primary importance. The AE DATA EXPERT system performs this task in three procedures: source separation, source purification and source classification. Basic production rules are discussed. (author) 19 refs.; 16 figs.; 2 tabs

Identifying and characterizing major emission point sources as a basis for geospatial distribution of mercury emissions inventories

Science.gov (United States)

Steenhuisen, Frits; Wilson, Simon J.

2015-07-01

Mercury is a global pollutant that poses threats to ecosystem and human health. Due to its global transport, mercury contamination is found in regions of the Earth that are remote from major emissions areas, including the Polar regions. Global anthropogenic emission inventories identify important sectors and industries responsible for emissions at a national level; however, to be useful for air transport modelling, more precise information on the locations of emission is required. This paper describes the methodology applied, and the results of work that was conducted to assign anthropogenic mercury emissions to point sources as part of geospatial mapping of the 2010 global anthropogenic mercury emissions inventory prepared by AMAP/UNEP. Major point-source emission sectors addressed in this work account for about 850 tonnes of the emissions included in the 2010 inventory. This work allocated more than 90% of these emissions to some 4600 identified point source locations, including significantly more point source locations in Africa, Asia, Australia and South America than had been identified during previous work to geospatially-distribute the 2005 global inventory. The results demonstrate the utility and the limitations of using existing, mainly public domain resources to accomplish this work. Assumptions necessary to make use of selected online resources are discussed, as are artefacts that can arise when these assumptions are applied to assign (national-sector) emissions estimates to point sources in various countries and regions. Notwithstanding the limitations of the available information, the value of this procedure over alternative methods commonly used to geo-spatially distribute emissions, such as use of 'proxy' datasets to represent emissions patterns, is illustrated. Improvements in information that would facilitate greater use of these methods in future work to assign emissions to point-sources are discussed. These include improvements to both national

Compound list: phenacetin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available phenacetin PCT 00138 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/phenacetin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/phenacetin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/phenacetin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch...ive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/phenacetin.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.bioscienc

Compound list: imipramine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available imipramine IMI 00069 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/imipramine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/imipramine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/imipramine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch...ive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/imipramine.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.bioscienc

Compound list: omeprazole [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available omeprazole OPZ 00012 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/omeprazole.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/omeprazole.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/omeprazole.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch...ive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/omeprazole.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.bioscienc

40 CFR 1054.501 - How do I run a valid emission test?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false How do I run a valid emission test... Procedures § 1054.501 How do I run a valid emission test? (a) Applicability. This subpart is addressed to you... provisions of 40 CFR 1065.405 describes how to prepare an engine for testing. However, you may consider...

Actualization and enlargement of the Upper Austrian emission inventory

International Nuclear Information System (INIS)

Winiwarter, W.; Schimak, G.; Raup, N.

2001-06-01

The functionality of the Upper Austrian emission inventory has been increased by simplifying the evaluation routines. Thus access to existing data will be simplified. This version 2.0 not only improves evaluation procedures already in place, but also allows to retrieve annual information on point sources, as routinely reported by the individual industrial facilities on an annual basis. In the same way as for such point source information, also statistical information is used to derive annual emission changes. This is currently limited to the sector of domestic heating, where emissions are directly influenced by climate parameters that can be easily obtained. Trend analysis currently is not possible due to the limited number of sectors included. First conclusions on the temporal behavior of emissions are still possible and are discussed here. Likewise, additional plausibility checks are facilitated by using temporal emission changes, which will help improve data quality. (author)

47 CFR 22.150 - Standard pre-filing technical coordination procedure.

Science.gov (United States)

2010-10-01

... this procedure for specific channels and types of stations are contained in the subparts governing the..., emission type and polarization. (4) Transmitting antenna pattern and maximum gain. (5) Transmitting antenna..., even if no channel usage conflicts are anticipated. If any notified party fails to respond within 30...

Trends of NO-, NO 2-, and NH 3-emissions from gasoline-fueled Euro-3- to Euro-4-passenger cars

Science.gov (United States)

Heeb, Norbert V.; Saxer, Christian J.; Forss, Anna-Maria; Brühlmann, Stefan

Vehicular emissions of reactive nitrogen compounds (RNCs) such as nitric oxide (NO), nitrogen dioxide (NO 2), and ammonia (NH 3) have a substantial impact on urban air quality. NO and NO 2 support the photochemical formation of ozone, and NH 3 is involved in the atmospheric formation of secondary aerosols. Vehicular NO is mainly formed during combustion, whereas NO 2 and NH 3 are both secondary pollutants of the catalytic converter systems. Herein we report on tail-pipe RNC emissions of gasoline-fueled Euro-3- and Euro-4-passenger cars at transient driving from 0 to 150 km h -1. Two sets of 10 in-use vehicles with comparable engine size and mileage were studied with time-resolved chemical ionization-mass spectrometry (CI-MS). Each vehicle was tested in 7 different driving cycles including the legislative European (EDC) and the US FTP-75 driving cycles. Mean emission factors (EFs) for different traffic situations are reported and effects of cold start, velocity, acceleration, and deceleration are discussed. Furthermore, critical operating conditions supporting the de novo formation of NH 3 have been identified. In the EDC, mean NO- and NH 3-EFs of 57±26 and 16±12 mg km -1 were obtained for Euro-3-vehicles; those of the Euro-4-technology were lower by about 25% and 33% at the levels of 43±46 and 10±7 mg km -1, respectively. NO 2 emissions of the investigated three-way catalyst (TWC) vehicles accounted for exhaust. Velocity and acceleration had pronounced effects on the RNC emission characteristics. Mean velocity-dependent EFs for NO and NH 3 varied by about one order of magnitude from 10 to 74 and 15 to 161 mg km -1 for Euro-3-vehicles and from 12 to 44 and 7 to 144 mg km -1 for the Euro-4 fleet. We conclude that the investigated Euro-3- and Euro-4-vehicles are mainly operated under slightly reducing conditions, where the NH 3 emissions dominate over those of the NO. Under these conditions, both vehicle fleets on an average fulfilled the valid Euro-3 and Euro-4

Compound list: caffeine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available caffeine CAF 00097 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/caffeine....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/caffeine....Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/caffeine...-tggates/LATEST/Rat/in_vivo/Liver/Repeat/caffeine.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.biosciencedbc.jp/ar...chive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/caffeine.Rat.in_vivo.Kidney.Single.zip ftp://ftp.bioscie

Compound list: bucetin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available bucetin BCT 00139 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_v...itro/bucetin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/bu...cetin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single.../bucetin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tgg...ates/LATEST/Rat/in_vivo/Liver/Repeat/bucetin.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.biosciencedbc.jp/archive

Compound list: lomustine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available lomustine LS 00049 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/lomustine....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/lomustine....Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/lomustine...pen-tggates/LATEST/Rat/in_vivo/Liver/Repeat/lomustine.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.biosciencedbc.j...p/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/lomustine.Rat.in_vivo.Kidney.Single.zip ftp://ftp.bi

Compound list: ethionine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available ethionine ET 00013 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/ethionine....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/ethionine....Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/ethionine...pen-tggates/LATEST/Rat/in_vivo/Liver/Repeat/ethionine.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.biosciencedbc.j...p/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/ethionine.Rat.in_vivo.Kidney.Single.zip ftp://ftp.bi

Theoretical and experimental studies on emissions from wood combustion

Energy Technology Data Exchange (ETDEWEB)

Skreiberg, Oeyvind

1997-12-31

This thesis discusses experiments on emissions from wood log combustion and single wood particle combustion, both caused by incomplete combustion and emissions of nitric and nitrous oxide, together with empirical and kinetic NO{sub x} modelling. Experiments were performed in three different wood stoves: a traditional stove, a staged air stove and a stove equipped with a catalytic afterburner. Ideally, biomass fuel does not give a net contribution to the greenhouse effect. However, incomplete combustion was found to result in significant greenhouse gas emissions. Empirical modelling showed the excess air ratio and the combustion chamber temperature to be the most important input variables controlling the total fuel-N to NO{sub x} conversion factor. As the result of an international round robin test of a wood stove equipped with a catalytic afterburner, particle emission measurements were found to be the best method to evaluate the environmental acceptability of the tested stove, since the particle emission level was least dependent of the national standards, test procedures and calculation procedures used. In batch single wood particle combustion experiments on an electrically heated small-scale fixed bed reactor the fuel-N to NO conversion factor varied between 0.11-0.86 depending on wood species and operating conditions. A parameter study and homogeneous kinetic modelling on a plug flow reactor showed that, depending on the combustion compliance in question, there is an optimum combination of primary excess air ratio, temperature and residence time that gives a maximum conversion of fuel-N to N{sub 2}. 70 refs., 100 figs., 26 tabs.

Compound list: phenobarbital [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available phenobarbital PB 00004 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human.../in_vitro/phenobarbital.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/...in_vitro/phenobarbital.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vivo/Liver/Single/phenobarbital.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscience

Compound list: sulfasalazine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available sulfasalazine SS 00034 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human.../in_vitro/sulfasalazine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/...in_vitro/sulfasalazine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vivo/Liver/Single/sulfasalazine.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscience

Compound list: methapyrilene [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available methapyrilene MP 00025 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human.../in_vitro/methapyrilene.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/...in_vitro/methapyrilene.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vivo/Liver/Single/methapyrilene.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscience

40 CFR 1060.520 - How do I test fuel tanks for permeation emissions?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false How do I test fuel tanks for... STATIONARY EQUIPMENT Test Procedures § 1060.520 How do I test fuel tanks for permeation emissions? Measure permeation emissions by weighing a sealed fuel tank before and after a temperature-controlled soak. (a...

Radionuclide air emissions at Department of Energy facilities

Energy Technology Data Exchange (ETDEWEB)

Duvall, K. [Department of Energy, Washington, DC (United States)

1995-02-01

Facilities operated by the U.S. Department of Energy (DOE) handle and process radioactive materials in conjunction with their research, nuclear materials production, remediation and waste disposal activities. Radionuclide emissions to the atmosphere from DOE facilities are regulated by the Environmental Protection Agency (EPA) under 40 CFR Part 61, Subpart H for emissions other than radon. Subpart H requires DOE to monitor emissions from stacks and calculate a potential offsite dose to an individual using EPA approved methods and procedures. DOE has applied to EPA for approval to use alternative methods for some of the EPA requirements for continuous monitoring. The use of alternative methods such as single-point sampling with a shrouded probe will have an impact at several major DOE facilities. These facilities are identified.

Study of PAH emission from the solid fuels combustion in residential furnaces

International Nuclear Information System (INIS)

Kakareka, Sergey V.; Kukharchyk, Tamara I.; Khomich, Valery S.

2005-01-01

The procedure for and results of a test study of polycyclic aromatic hydrocarbon (PAH) emission from a few types of solid fuels combustion in residential furnaces of various designs typical for Belarus are discussed. Greatest levels of PAH emission were detected from domestic wastes and wood waste combustion. Lowest levels of PAH emission are from peat briquette combustion. It was found that PAH concentration in off-gases from firewood combustion also varies significantly depending on the type of wood: the highest values of PAH are typical for waste gases from birch firewood combustion in comparison with pine firewood combustion. Draft PAH emission factors are proposed with intended application for emission inventory of such installations

The effect of urbanization and industrialization on carbon emissions in Turkey: evidence from ARDL bounds testing procedure.

Science.gov (United States)

Pata, Ugur Korkut

2018-03-01

This paper examines the dynamic short- and long-term relationship between per capita GDP, per capita energy consumption, financial development, urbanization, industrialization, and per capita carbon dioxide (CO 2 ) emissions within the framework of the environmental Kuznets curve (EKC) hypothesis for Turkey covering the period from 1974 to 2013. According to the results of the autoregressive distributed lag bounds testing approach, an increase in per capita GDP, per capita energy consumption, financial development, urbanization, and industrialization has a positive effect on per capita CO 2 emissions in the long term, and also the variables other than urbanization increase per capita CO 2 emissions in the short term. In addition, the findings support the validity of the EKC hypothesis for Turkey in the short and long term. However, the turning points obtained from long-term regressions lie outside the sample period. Therefore, as the per capita GDP increases in Turkey, per capita CO 2 emissions continue to increase.

N-15 analysis by emission spectroscopy

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-12-31

The stable isotope of nitrogen, N-15, has become widely used as tracer in agriculture, medicine and biology research. The film gives an overview of the sample preparation and analytical procedures followed in the analysis of the nitrogen isotopic composition (14N/15N ratio) by optical emission spectrometry at the Seibersdorf Laboratory. The subsampling of plant material and the several steps of chemical pretreatment such as Kjeldahl digestion, distillation, titration and adjustment of the proper N concentration in the extract are demonstrated. The preparation of the discharge tubes is shown in detail. Final measurement of the 14N/15N ratio is carried out with the NOI-5 and JASCO emission spectrometers

Compound list: meloxicam [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available meloxicam MLX 00124 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in..._vitro/meloxicam.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitr...o/meloxicam.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/...Single/meloxicam.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/

Compound list: disopyramide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available disopyramide DIS 00102 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human.../in_vitro/disopyramide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/i...n_vitro/disopyramide.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...vo/Liver/Single/disopyramide.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc

Compound list: ethionamide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available ethionamide ETH 00135 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/ethionamide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vitro/ethionamide.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/...Liver/Single/ethionamide.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/

Compound list: tetracycline [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available tetracycline TC 00048 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/tetracycline.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vitro/tetracycline.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_viv...o/Liver/Single/tetracycline.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.

Compound list: diclofenac [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available diclofenac DFNa 00019 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/diclofenac.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_v...itro/diclofenac.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Li...ver/Single/diclofenac.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arc

Compound list: theophylline [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available theophylline TEO 00096 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human.../in_vitro/theophylline.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/i...n_vitro/theophylline.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...vo/Liver/Single/theophylline.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc

Compound list: pemoline [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available pemoline PML 00051 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_...vitro/pemoline.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/...pemoline.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Sin...gle/pemoline.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open

Compound list: griseofulvin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available griseofulvin GF 00043 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/griseofulvin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vitro/griseofulvin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_viv...o/Liver/Single/griseofulvin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.

Compound list: carbamazepine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available carbamazepine CBZ 00018 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Huma...n/in_vitro/carbamazepine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat.../in_vitro/carbamazepine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vivo/Liver/Single/carbamazepine.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscienc

Compound list: benziodarone [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available benziodarone BZD 00130 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human.../in_vitro/benziodarone.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/i...n_vitro/benziodarone.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...vo/Liver/Single/benziodarone.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc

Compound list: quinidine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available quinidine QND 00074 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in..._vitro/quinidine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitr...o/quinidine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/...Single/quinidine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/

Compound list: naproxen [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available naproxen NPX 00073 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_...vitro/naproxen.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/...naproxen.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Sin...gle/naproxen.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open

Compound list: nitrofurazone [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available nitrofurazone NFZ 00065 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Huma...n/in_vitro/nitrofurazone.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat.../in_vitro/nitrofurazone.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vivo/Liver/Single/nitrofurazone.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscienc

Compound list: trimethadione [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available trimethadione TMD 00122 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Huma...n/in_vitro/trimethadione.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat.../in_vitro/trimethadione.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vivo/Liver/Single/trimethadione.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscienc

Compound list: ticlopidine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available ticlopidine TCP 00146 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/ticlopidine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vitro/ticlopidine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/...Liver/Single/ticlopidine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/

Compound list: hydroxyzine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available hydroxyzine HYZ 00071 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/hydroxyzine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vitro/hydroxyzine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/...Liver/Single/hydroxyzine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/

Compound list: ibuprofen [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available ibuprofen IBU 00072 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in..._vitro/ibuprofen.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitr...o/ibuprofen.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/...Single/ibuprofen.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/

Compound list: chlormezanone [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available chlormezanone CMN 00052 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Huma...n/in_vitro/chlormezanone.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat.../in_vitro/chlormezanone.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vivo/Liver/Single/chlormezanone.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscienc

Compound list: chlorpropamide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available chlorpropamide CPP 00080 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Hum...an/in_vitro/chlorpropamide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/R...at/in_vitro/chlorpropamide.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat.../in_vivo/Liver/Single/chlorpropamide.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosc

Compound list: azathioprine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available azathioprine AZP 00046 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human.../in_vitro/azathioprine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/i...n_vitro/azathioprine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...vo/Liver/Single/azathioprine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc

Compound list: simvastatin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available simvastatin SST 00117 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/simvastatin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vitro/simvastatin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/...Liver/Single/simvastatin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/

Compound list: phenytoin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available phenytoin PHE 00026 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in..._vitro/phenytoin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitr...o/phenytoin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/...Single/phenytoin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/

Compound list: sulindac [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available sulindac SUL 00100 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_...vitro/sulindac.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/...sulindac.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Sin...gle/sulindac.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open

Compound list: metformin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available metformin MFM 00053 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in..._vitro/metformin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitr...o/metformin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/...Single/metformin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/

Compound list: methimazole [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available methimazole MTZ 00057 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/methimazole.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vitro/methimazole.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/...Liver/Single/methimazole.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/

Compound list: bendazac [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available bendazac BDZ 00129 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_...vitro/bendazac.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/...bendazac.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Sin...gle/bendazac.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open

Compound list: sulpiride [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available sulpiride SLP 00115 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in..._vitro/sulpiride.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitr...o/sulpiride.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/...Single/sulpiride.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/

Compound list: fenofibrate [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available fenofibrate FFB 00079 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/fenofibrate.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vitro/fenofibrate.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/...Liver/Single/fenofibrate.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/

Compound list: thioridazine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available thioridazine TRZ 00038 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human.../in_vitro/thioridazine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/i...n_vitro/thioridazine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...vo/Liver/Single/thioridazine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc

Compound list: acarbose [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available acarbose ACA 00116 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_...vitro/acarbose.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/...acarbose.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Sin...gle/acarbose.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open

Compound list: isoniazid [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available isoniazid INAH 00002 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/isoniazid.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vit...ro/isoniazid.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver.../Single/isoniazid.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive

Compound list: labetalol [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available labetalol LBT 00040 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in..._vitro/labetalol.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitr...o/labetalol.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/...Single/labetalol.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/

Wet flue gas desulphurisation procedures and relevant solvents thermophysical properties determination

Directory of Open Access Journals (Sweden)

Živković Nikola V.

2014-01-01

Full Text Available In order to mitigate climate change, the priority task is to reduce emissions of greenhouse gases, including sulfur oxides, from stationary power plants. The legal framework of the European Union has limited the allowable emissions of gases with harmful effects and fulfillment of this obligation is also ahead of the Republic of Serbia in the following years. In this paper categorization of wet procedures for sulfur oxides removal is given. Wet procedure with the most widespread industrial application, lime/limestone process, has been described in detail. In addition, the procedures with chemical and physical absorption and solvent thermal regeneration, which recently gained more importance, have been presented. Experimentally determined thermophysical and transport properties of commercially used and alternative solvents, necessary for the equipment design and process optimization, are also given in the paper. The obtained values of densities and viscosities of pure chemicals - solvents, polyethylene glycol 200 (PEG 200, polyethylene glycol 400 (PEG 400, tetraethylene glycol dimethyl ether (TEGDMA, N-methyl-2-pyrolidon (NMP and dimethylaniline (DMA, measured at the atmospheric pressure, are presented as a function of temperature. [Projekat Ministarstva nauke Republike Srbije, br. 172063

Effects of Mid-Level Ethanol Blends on Conventional Vehicle Emissions

Energy Technology Data Exchange (ETDEWEB)

Knoll, K.; West, B.; Huff, S.; Thomas, J.; Orban, J.; Cooper, C.

2010-06-01

Tests were conducted in 2008 on 16 late-model conventional vehicles (1999-2007) to determine short-term effects of mid-level ethanol blends on performance and emissions. Vehicle odometer readings ranged from 10,000 to 100,000 miles, and all vehicles conformed to federal emissions requirements for their federal certification level. The LA92 drive cycle, also known as the Unified Cycle, was used for testing because it more accurately represents real-world acceleration rates and speeds than the Federal Test Procedure. Test fuels were splash-blends of up to 20 volume percent ethanol with federal certification gasoline. Both regulated and unregulated air-toxic emissions were measured. For the 16-vehicle fleet, increasing ethanol content resulted in reductions in average composite emissions of both nonmethane hydrocarbons and carbon monoxide and increases in average emissions of ethanol and aldehydes.

Compound list: ciprofloxacin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available ciprofloxacin CPX 00050 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Huma...n/in_vitro/ciprofloxacin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat.../in_vitro/ciprofloxacin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vivo/Liver/Single/ciprofloxacin.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscienc...edbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/ciprofloxacin.Rat.in_vivo.Liver.Repeat.zip ftp:

Compound list: monocrotaline [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available monocrotaline MCT 00058 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Huma...n/in_vitro/monocrotaline.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat.../in_vitro/monocrotaline.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vivo/Liver/Single/monocrotaline.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscienc...edbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/monocrotaline.Rat.in_vivo.Liver.Repeat.zip ftp:

40 CFR 1048.501 - How do I run a valid emission test?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false How do I run a valid emission test... § 1048.501 How do I run a valid emission test? (a) Use the equipment and procedures for spark-ignition... 86.132-96(h) and then operate the engine for 60 minutes over repeat runs of the duty cycle specified...

Electrolytic cell-free 57Co deposition for emission Mössbauer spectroscopy

Science.gov (United States)

Zyabkin, Dmitry V.; Procházka, Vít; Miglierini, Marcel; Mašláň, Miroslav

2018-05-01

We have developed a simple, inexpensive and efficient method for an electrochemical preparation of samples for emission Mössbauer spectroscopy (EMS) and Mössbauer sources. The proposed electrolytic deposition procedure does not require any special setup, not even an electrolytic cell. It utilizes solely an electrode with a droplet of electrolyte on its surface and the second electrode sunk into the droplet. Its performance is demonstrated using two examples, a metallic glass and a Cu stripe. We present a detailed description of the deposition procedure and resulting emission Mössbauer spectra for both samples. In the case of a Cu stripe, we have performed EMS measurements at different stages of heat-treatment, which are required for the production of Mössbauer sources with the copper matrix.

New trends in emission control in the European Union

CERN Document Server

Merkisz, Jerzy; Radzimirski, Stanislaw

2014-01-01

This book discusses recent changes in the European legislation for exhaust emissions from motor vehicles. It starts with a comprehensive explanation of both the structure and range of applicability of new regulations, such as Euro 5 and Euro 6 for light-duty vehicles and Euro VI for heavy-duty vehicles. Then it introduces the most important issues in in-service conformity and conformity of production for vehicles, describing the latest procedures for performing exhaust emissions tests under both bench and operating conditions. Subsequently, it reports on portable emission measurement systems (PEMS) and their application for assessing the emissions of gaseous and particulate matter alike, under actual operating conditions and in all transport modes. Lastly, the book presents selected findings from exhaust emissions research on engines for a variety of transport vehicles, such as light-duty and heavy-duty vehicles, as well as non-road vehicles, which include farm tractors, groundwork and forest machinery, diese...

Compound list: famotidine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available famotidine FAM 00085 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/famotidine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/famotidine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/famotidine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: nifedipine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available nifedipine NIF 00091 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/nifedipine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/nifedipine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/nifedipine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: perhexiline [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available perhexiline PH 00045 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/perhexiline.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_v...itro/perhexiline.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/L...iver/Single/perhexiline.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/a

Compound list: colchicine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available colchicine COL 00113 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/colchicine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/colchicine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/colchicine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: ranitidine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available ranitidine RAN 00086 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/ranitidine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/ranitidine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/ranitidine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: nimesulide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available nimesulide NIM 00136 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/nimesulide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/nimesulide.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/nimesulide.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: tannic acid [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available tannic acid TAN 00093 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/...in_vitro/tannic_acid.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_...vitro/tannic_acid.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/...Liver/Single/tannic_acid.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/

Compound list: dantrolene [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available dantrolene DTL 00119 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/dantrolene.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/dantrolene.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/dantrolene.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: moxisylyte [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available moxisylyte MXS 00061 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/moxisylyte.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/moxisylyte.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/moxisylyte.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: iproniazid [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available iproniazid IPA 00062 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/iproniazid.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/iproniazid.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/iproniazid.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: methyldopa [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available methyldopa MDP 00056 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/methyldopa.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/methyldopa.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/methyldopa.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: mexiletine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available mexiletine MEX 00103 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/mexiletine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/mexiletine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/mexiletine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: lornoxicam [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available lornoxicam LNX 00125 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/lornoxicam.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/lornoxicam.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/lornoxicam.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: mefenamic acid [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available mefenamic acid MEF 00084 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Hum...an/in_vitro/mefenamic_acid.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/R...at/in_vitro/mefenamic_acid.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat.../in_vivo/Liver/Single/mefenamic_acid.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosc

Compound list: phalloidin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available phalloidin PHA 00A11 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/phalloidin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/phalloidin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/phalloidin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: cimetidine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available cimetidine CIM 00035 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/i...n_vitro/cimetidine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vi...tro/cimetidine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/cimetidine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/arch

Compound list: nicotinic acid [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available nicotinic acid NIC 00081 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Hum...an/in_vitro/nicotinic_acid.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/R...at/in_vitro/nicotinic_acid.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat.../in_vivo/Liver/Single/nicotinic_acid.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosc

Compound list: carboplatin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available carboplatin CBP 00133 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vitro/carboplatin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo.../Liver/Single/carboplatin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATES...T/Rat/in_vivo/Liver/Repeat/carboplatin.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.bio...sciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/carboplatin.Rat.in_vivo.Kidney.Single.zip ftp:

Compound list: cephalothin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available cephalothin CLT 00141 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vitro/cephalothin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo.../Liver/Single/cephalothin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATES...T/Rat/in_vivo/Liver/Repeat/cephalothin.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.bio...sciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/cephalothin.Rat.in_vivo.Kidney.Single.zip ftp:

Compound list: triamterene [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available triamterene TRI 00101 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in..._vitro/triamterene.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo.../Liver/Single/triamterene.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATES...T/Rat/in_vivo/Liver/Repeat/triamterene.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.bio...sciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/triamterene.Rat.in_vivo.Kidney.Single.zip ftp:

Compound list: nitrofurantoin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available nitrofurantoin NFT 00020 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Hum...an/in_vitro/nitrofurantoin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/R...at/in_vitro/nitrofurantoin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat.../in_vivo/Liver/Single/nitrofurantoin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosc...iencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/nitrofurantoin.Rat.in_vivo.Liver.Repeat.zip ftp:

Compound list: amphotericin B [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available amphotericin B AMB 00157 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Hum...an/in_vitro/amphotericin_B.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/R...at/in_vivo/Liver/Single/amphotericin_B.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-...tggates/LATEST/Rat/in_vivo/Liver/Repeat/amphotericin_B.Rat.in_vivo.Liver.Repeat.zip ftp:...//ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/amphotericin_B.Rat.in_vivo.Kidney.Single.zip ftp:

Compound list: cisplatin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available cisplatin CSP 00132 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_v...itro/cisplatin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liv...er/Single/cisplatin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/...in_vivo/Liver/Repeat/cisplatin.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.bioscienced...bc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/cisplatin.Rat.in_vivo.Kidney.Single.zip ftp://ft

Room chamber assessment of the pollutant emission properties of (nominally) low-emission unflued gas heaters

Energy Technology Data Exchange (ETDEWEB)

Brown, S.K.; Mahoney, K.J., Min Cheng [CSIRO Manufacturing and Infrastructure Technology, Victoria (Australia)

2004-07-01

Pollutant emissions from unflued gas heaters were assessed in CSIRO'a Room Dynamic Environmental Chamber. This paper describes the chamber assessment procedure and presents findings for major commercial heaters that are nominally 'low-emission'. The chamber was operated at controlled conditions of temperature, humidity, ventilation and air mixing, representative of those encountered in typical indoor environments. A fixed rate of heat removal from the chamber air ensured that the heaters operated at constant heating rates, typically {approx}6 MJ/h which simulated operation of a heater after warm-up in an insulated dwelling in south-east Australia. The pollutants assessed were nitrogen dioxide, carbon monoxide, formaldehyde, VOCs and respirable suspended particulates. One type of heater was lower emitting for nigroen dioxide, but emitted greater amounts of carbon monoxide and formaldehyde (the latter becoming significant to indoor air quality). When operated with low line pressure of slight misalignment of the gas burner, this heater became a hazardous source of these pollutants. Emissions from the heates changed little after continous operation for up to 2 months. (au)

Compound list: WY-14643 [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available WY-14643 WY 00030 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_v...itro/WY-14643.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/W...Y-14643.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Sing...le/WY-14643.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-

40 CFR 1060.521 - How do I test fuel caps for permeation emissions?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false How do I test fuel caps for permeation... EQUIPMENT Test Procedures § 1060.521 How do I test fuel caps for permeation emissions? If you measure a fuel tank's permeation emissions with a nonpermeable covering in place of the fuel cap under § 1060.520(b)(5...

Regulated and unregulated emissions from modern 2010 emissions-compliant heavy-duty on-highway diesel engines

Science.gov (United States)

Khalek, Imad A.; Blanks, Matthew G.; Merritt, Patrick M.; Zielinska, Barbara

2015-01-01

The U.S. Environmental Protection Agency (EPA) established strict regulations for highway diesel engine exhaust emissions of particulate matter (PM) and nitrogen oxides (NOx) to aid in meeting the National Ambient Air Quality Standards. The emission standards were phased in with stringent standards for 2007 model year (MY) heavy-duty engines (HDEs), and even more stringent NOX standards for 2010 and later model years. The Health Effects Institute, in cooperation with the Coordinating Research Council, funded by government and the private sector, designed and conducted a research program, the Advanced Collaborative Emission Study (ACES), with multiple objectives, including detailed characterization of the emissions from both 2007- and 2010-compliant engines. The results from emission testing of 2007-compliant engines have already been reported in a previous publication. This paper reports the emissions testing results for three heavy-duty 2010-compliant engines intended for on-highway use. These engines were equipped with an exhaust diesel oxidation catalyst (DOC), high-efficiency catalyzed diesel particle filter (DPF), urea-based selective catalytic reduction catalyst (SCR), and ammonia slip catalyst (AMOX), and were fueled with ultra-low-sulfur diesel fuel (~6.5 ppm sulfur). Average regulated and unregulated emissions of more than 780 chemical species were characterized in engine exhaust under transient engine operation using the Federal Test Procedure cycle and a 16-hr duty cycle representing a wide dynamic range of real-world engine operation. The 2010 engines’ regulated emissions of PM, NOX, nonmethane hydrocarbons, and carbon monoxide were all well below the EPA 2010 emission standards. Moreover, the unregulated emissions of polycyclic aromatic hydrocarbons (PAHs), nitroPAHs, hopanes and steranes, alcohols and organic acids, alkanes, carbonyls, dioxins and furans, inorganic ions, metals and elements, elemental carbon, and particle number were substantially

Agreements on emission of greenhouse gases

International Nuclear Information System (INIS)

Aulstad, Johan Greger

2001-01-01

Agreements on emission of greenhouse gases is one of the instruments used by Norwegian authorities to meet their obligations with respect to the Climate Convention and the Kyoto Protocol. This book discusses the legal issues raised by these agreements. A main topic is how the industrial emissions conform to the Pollution Act. Does the Pollution Act apply to these emissions? What is the impact of the sanction rules in this act on the emissions? The book also deals with the following general questions that arise in connection with the application of public authority: (1) Can the administration grant concessions and permits in the form of agreements? (2) What commitments can be imposed on a private party by the administration by agreement? (3) Should the procedures set down in the Pollution Act and in the Public Administration Act be followed fully when the pollution authorities make agreements? Is the opportunity of the administration to reverse more restricted when they make agreements than when they make one-sided decisions? Although this discussion primarily deals with the emission of greenhouse gases, the reasoning and conclusions are relevant in many other types of agreements in which the public administration is one of the parties. The agreement that regulates the emissions of greenhouse gases from the Norwegian aluminium industry is described in a special section. The book also gives a brief account of how agreements are used in the Danish climate policy

State and Territory Greenhouse Gas Emissions. An overview

International Nuclear Information System (INIS)

2005-04-01

This document is a summary of the latest available estimates of greenhouse gas emissions for the States and Territories. They are taken from the national inventory and show emissions for 2002, the latest year for which national statistics on fuel and electricity consumption are available. The report shows that Australia's total greenhouse gas emissions in 2002 amounted to 541.8 million tonnes. The State and Territory breakdown was: New South Wales: 151.5 million tonnes (Mt); Queensland: 145.1 Mt; Victoria: 117.0 Mt; Western Australia: 70.4 Mt; South Australia: 30.9 Mt; Northern Territory: 17.7 Mt; Tasmania: 7.2 Mt; ACT: 1.3 Mt. The State and Territory inventories are the first of what will be an annual series. The national inventory and State and Territory inventories are all prepared according to the international rules and procedures applicable to Australia's Kyoto 108% emissions target. The national inventory undergoes regular independent international review

Compound list: ajmaline [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available ajmaline AJM 00118 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/ajmaline....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/ajmaline....Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/ajmaline.Rat.in_vivo.Liver.Single.zip ftp://ftp.bi...-tggates/LATEST/Rat/in_vivo/Liver/Repeat/ajmaline.Rat.in_vivo.Liver.Repeat.zip ...

40 CFR 86.1217-96 - Evaporative emission enclosure calibrations.

Science.gov (United States)

2010-07-01

... procedure: (1) Carefully measure the internal length, width and height of the enclosure, accounting for... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Evaporative emission enclosure calibrations. 86.1217-96 Section 86.1217-96 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...

Motivational power of future time perspective: Meta-analyses in education, work, and health.

Science.gov (United States)

Andre, Lucija; van Vianen, Annelies E M; Peetsma, Thea T D; Oort, Frans J

2018-01-01

Future time perspective (FTP) may predict individual attitudes and behaviors. However, FTP research includes different FTP conceptualizations and outcomes which hinder generalizing its findings. To solve the inconsistencies in FTP research and generalize the magnitude of FTP as a driver of motivation and behavior, we conducted the first systematical synthesis of FTP relationships in three crucial life domains. Our meta-analyses of FTP studies in education (k = 28), work (k = 17), and health (k = 32) involved N = 31,558 participants, and used a conceptual model for grouping FTP constructs. To address different outcome types, we applied the Theory of Planned Behavior when coding the studies. FTP relationships with outcomes were small-to-medium, were generalizable across domains, and were strongest when the FTP construct included a mixture of cognition, behavioral intention, and affect and, in education, when the FTP measure was domain specific rather than general. There were cross-cultural differences in FTP-outcome relationships. The strength of the FTP-outcome types relationship varied for attitudes, perceived behavioral control, behavioral intention, and behaviors. The lowest effect sizes were found for FTP predicting actual behaviors in education, work, and health and between FTP and health attitudes. Theoretical implications of the findings and future research directions are discussed.

Motivational power of future time perspective: Meta-analyses in education, work, and health.

Directory of Open Access Journals (Sweden)

Lucija Andre

Full Text Available Future time perspective (FTP may predict individual attitudes and behaviors. However, FTP research includes different FTP conceptualizations and outcomes which hinder generalizing its findings. To solve the inconsistencies in FTP research and generalize the magnitude of FTP as a driver of motivation and behavior, we conducted the first systematical synthesis of FTP relationships in three crucial life domains. Our meta-analyses of FTP studies in education (k = 28, work (k = 17, and health (k = 32 involved N = 31,558 participants, and used a conceptual model for grouping FTP constructs. To address different outcome types, we applied the Theory of Planned Behavior when coding the studies. FTP relationships with outcomes were small-to-medium, were generalizable across domains, and were strongest when the FTP construct included a mixture of cognition, behavioral intention, and affect and, in education, when the FTP measure was domain specific rather than general. There were cross-cultural differences in FTP-outcome relationships. The strength of the FTP-outcome types relationship varied for attitudes, perceived behavioral control, behavioral intention, and behaviors. The lowest effect sizes were found for FTP predicting actual behaviors in education, work, and health and between FTP and health attitudes. Theoretical implications of the findings and future research directions are discussed.

Motivational power of future time perspective: Meta-analyses in education, work, and health

Science.gov (United States)

2018-01-01

Future time perspective (FTP) may predict individual attitudes and behaviors. However, FTP research includes different FTP conceptualizations and outcomes which hinder generalizing its findings. To solve the inconsistencies in FTP research and generalize the magnitude of FTP as a driver of motivation and behavior, we conducted the first systematical synthesis of FTP relationships in three crucial life domains. Our meta-analyses of FTP studies in education (k = 28), work (k = 17), and health (k = 32) involved N = 31,558 participants, and used a conceptual model for grouping FTP constructs. To address different outcome types, we applied the Theory of Planned Behavior when coding the studies. FTP relationships with outcomes were small-to-medium, were generalizable across domains, and were strongest when the FTP construct included a mixture of cognition, behavioral intention, and affect and, in education, when the FTP measure was domain specific rather than general. There were cross-cultural differences in FTP-outcome relationships. The strength of the FTP-outcome types relationship varied for attitudes, perceived behavioral control, behavioral intention, and behaviors. The lowest effect sizes were found for FTP predicting actual behaviors in education, work, and health and between FTP and health attitudes. Theoretical implications of the findings and future research directions are discussed. PMID:29364917

Compound list: nitrosodiethylamine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available nitrosodiethylamine DEN 00145 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATES...s/LATEST/Rat/in_vitro/nitrosodiethylamine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tgg...ates/LATEST/Rat/in_vivo/Liver/Single/nitrosodiethylamine.Rat.in_vivo.Liver.Single....zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/nitrosodiethylamine.Rat.in_vivo.Liver.Repeat.zip ... ...T/Human/in_vitro/nitrosodiethylamine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggate

Compound list: hexachlorobenzene [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available hexachlorobenzene HCB 00022 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/...Human/in_vitro/hexachlorobenzene.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LA...TEST/Rat/in_vitro/hexachlorobenzene.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/L...ATEST/Rat/in_vivo/Liver/Single/hexachlorobenzene.Rat.in_vivo.Liver.Single.zip ftp...://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/hexachlorobenzene.Rat.in_vivo.L

Compound list: aspirin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available aspirin ASA 00014 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/aspirin....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/aspirin....Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/aspirin....Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/aspirin.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: ethanol [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available ethanol ETN 00137 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_v...itro/ethanol.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/et...hanol.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single.../ethanol.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/ethanol.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: adapin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available adapin ADP 00039 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vi...tro/adapin.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/adap...in.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/ad...apin.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/adapin.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: danazol [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available danazol DNZ 00127 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_v...itro/danazol.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/da...nazol.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single.../danazol.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/danazol.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: tacrine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available tacrine TAC 00060 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_v...itro/tacrine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/ta...crine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single.../tacrine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/tacrine.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: bromoethylamine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available bromoethylamine BEA 00134 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/bromoethylam...ine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST...Rat/in_vivo/Liver/Single/bromoethylamine.Rat.in_vivo.Liver.Single.zip ftp://ftp.b...iosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/bromoethylamine.Rat.in_vivo.Liver.Repea...t.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/bromoethylamine.Rat.i

NWCF Evaporator Tank System 2001 Offgas Emissions Inventory

Energy Technology Data Exchange (ETDEWEB)

Boardman, Richard Doin; Lamb, Kenneth Mitchel; Matejka, Leon Anthony; Nenni, Joseph A

2002-02-01

An offgas emissions inventory and liquid stream characterization of the Idaho New Waste Calcining Facility (NWCF) Evaporator Tank System (ETS), formerly known as the High Level Liquid Waste Evaporator (HLLWE), has been completed. The emissions rates of volatile and semi-volatile organic compounds, multiple metals, particulate, and hydrochloric acid were measured in accordance with an approved Quality Assurance Project Plan (QAPjP) and Test Plan that invoked U.S. Environmental Protection Agency (EPA) standard sample collection and analysis procedures. Offgas samples were collected during the start up and at the end of evaporator batches when it was hypothesized the emissions would be at peak rates. Corresponding collection of samples from the evaporator feed overhead condensate, and bottoms was made at approximately the same time as the emissions inventory to support material balance determinations for the evaporator process. The data indicate that organic compound emissions are slightly higher at the beginning of the batch while metals emissions, including mercury, are slightly higher at the end of the evaporator batch. The maximum emissions concentrations are low for all constituents of primary concern. Mercury emissions were less than 5 ppbv, while the sum of HCl and Cl2 emissions was less than 1 ppmv. The sum of all organic emissions also was less than 1 ppmv. The estimated hazardous quotient (HQ) for the evaporator was 6.2e-6 as compared to 0.25 for the EPA target criteria. The cancer risk was 1.3e-10 compared to an EPA target of le-5.

NWCF Evaporator Tank System 2001 Offgas Emissions Inventory

International Nuclear Information System (INIS)

Boardman, R.D.; Lamb, K.M.; Matejka, L.A.; Nenni, J.A.

2002-01-01

An offgas emissions inventory and liquid stream characterization of the Idaho New Waste Calcining Facility (NWCF) Evaporator Tank System (ETS), formerly known as the High Level Liquid Waste Evaporator (HLLWE), has been completed. The emissions rates of volatile and semi-volatile organic compounds, multiple metals, particulate, and hydrochloric acid were measured in accordance with an approved Quality Assurance Project Plan (QAPjP) and Test Plan that invoked U.S. Environmental Protection Agency (EPA) standard sample collection and analysis procedures. Offgas samples were collected during the start up and at the end of evaporator batches when it was hypothesized the emissions would be at peak rates. Corresponding collection of samples from the evaporator feed overhead condensate, and bottoms was made at approximately the same time as the emissions inventory to support material balance determinations for the evaporator process. The data indicate that organic compound emissions are slightly higher at the beginning of the batch while metals emissions, including mercury, are slightly higher at the end of the evaporator batch. The maximum emissions concentrations are low for all constituents of primary concern. Mercury emissions were less than 5 ppbv, while the sum of HCl and Cl2 emissions was less than 1 ppmv. The sum of all organic emissions also was less than 1 ppmv. The estimated hazardous quotient (HQ) for the evaporator was 6.2e-6 as compared to 0.25 for the EPA target criteria. The cancer risk was 1.3e-10 compared to an EPA target of le-5

Compound list: propylthiouracil [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available propylthiouracil PTU 00029 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/H...uman/in_vitro/propylthiouracil.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATE...ST/Rat/in_vitro/propylthiouracil.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATE...ST/Rat/in_vivo/Liver/Single/propylthiouracil.Rat.in_vivo.Liver.Single.zip ftp://f

40 CFR 86.1233-96 - Diurnal emission test.

Science.gov (United States)

2010-07-01

... Emission Test Procedures for New Gasoline-Fueled, Natural Gas-Fueled, Liquefied Petroleum Gas-Fueled and... minimum wind speed of 5 mph (8 km/hr) under the fuel tank of the test vehicle. The Administrator may adjust fan speed and location to ensure sufficient air circulation around the fuel tank. The wind speed...

40 CFR 1051.515 - How do I test my fuel tank for permeation emissions?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false How do I test my fuel tank for... Procedures § 1051.515 How do I test my fuel tank for permeation emissions? Measure permeation emissions by weighing a sealed fuel tank before and after a temperature-controlled soak. (a) Preconditioning fuel soak...

Reducing energy consumption and CO{sub 2} emissions in thermally coupled azeotropic distillation

Energy Technology Data Exchange (ETDEWEB)

Sun, L.Y.; Chang, X.W.; Zhang, Y.M.; Li, J.; Li, Q.S. [Department of Chemical Engineering, China University of Petroleum, Qingdao, Shandong Province (China)

2010-03-15

The design and optimization procedures of a heterogeneous thermally coupled azeotropic distillation sequence with a side stripper (TCADS-SS) for the purification of isopropanol has been investigated. The proposed procedures can detect the optimal values of the design variables and thereby guarantee the minimum energy consumption, which is related to the minimum CO{sub 2} emissions and the lowest total annual cost (TAC). The procedures are applied to the study of the separation of azeotropic mixtures using the two distillation sequences. In the TCADS-SS, the top end of the side stripper has both liquid and vapor exchange with the main column, which eliminates a condenser in contrast with the conventional heterogeneous azeotropic distillation sequence (CHADS). The results show that not only reductions in energy consumption and CO{sub 2} emissions but also higher thermodynamic efficiency can be obtained for the TCADS-SS. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Compound list: methyltestosterone [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available methyltestosterone MTS 00041 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/methyltes...LATEST/Rat/in_vitro/methyltestosterone.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggate...s/LATEST/Rat/in_vivo/Liver/Single/methyltestosterone.Rat.in_vivo.Liver.Single.zip... ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/methyltestosterone.Rat.in_v...ivo.Liver.Repeat.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/methyltest

Compound list: thioacetamide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available thioacetamide TAA 00017 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/thioacetamide.Human.in_vitro.Liver.zip ftp:...//ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/thioacetam..._vivo/Liver/Single/thioacetamide.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscienc...edbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/thioacetamide.Rat.in_vivo.Liver.Repeat.zip ftp:...//ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/thioacetamide.Rat.in_vivo.Kidne

Compound list: ethinylestradiol [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available ethinylestradiol EE 00055 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Hu...man/in_vitro/ethinylestradiol.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATES...T/Rat/in_vitro/ethinylestradiol.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATES...T/Rat/in_vivo/Liver/Single/ethinylestradiol.Rat.in_vivo.Liver.Single.zip ftp://ft...p.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/ethinylestradiol.Rat.in_vivo.Liver.Repeat.zip ftp:

Compound list: acetazolamide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available acetazolamide ACZ 00108 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/acetazolam...ide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/acetazolam..._vivo/Liver/Single/acetazolamide.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscienc...edbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/acetazolamide.Rat.in_vivo.Liver.Repeat.zip ftp:...//ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/acetazolamide.Rat.in_vivo.Kidne

Compound list: naphthyl isothiocyanate [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available naphthyl isothiocyanate ANIT 00009 ftp://ftp.biosciencedbc.jp/archive/open-tggates/...LATEST/Human/in_vitro/naphthyl_isothiocyanate.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/op...en-tggates/LATEST/Rat/in_vitro/naphthyl_isothiocyanate.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/arc...hive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/naphthyl_isothiocyanate.Rat.in_...vivo.Liver.Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/naphthyl_isothiocyanate.Rat.in_vivo.Liver.Repeat.zip ...

The evolution of young HII regions. I. Continuum emission and internal dynamics

Science.gov (United States)

Klaassen, P. D.; Johnston, K. G.; Urquhart, J. S.; Mottram, J. C.; Peters, T.; Kuiper, R.; Beuther, H.; van der Tak, F. F. S.; Goddi, C.

2018-04-01

Context. High-mass stars form in much richer environments than those associated with isolated low-mass stars, and once they reach a certain mass, produce ionised (HII) regions. The formation of these pockets of ionised gas are unique to the formation of high-mass stars (M > 8 M⊙), and present an excellent opportunity to study the final stages of accretion, which could include accretion through the HII region itself. Aim. This study of the dynamics of the gas on both sides of these ionisation boundaries in very young HII regions aims to quantify the relationship between the HII regions and their immediate environments. Methods: We present high-resolution ( 0.5″) ALMA observations of nine HII regions selected from the red MSX source survey with compact radio emission and bolometric luminosities greater than 104 L⊙. We focus on the initial presentation of the data, including initial results from the radio recombination line H29α, some complementary molecules, and the 256 GHz continuum emission. Results: Of the six (out of nine) regions with H29α detections, two appear to have cometary morphologies with velocity gradients across them, and two appear more spherical with velocity gradients suggestive of infalling ionised gas. The remaining two were either observed at low resolution or had signals that were too weak to draw robust conclusions. We also present a description of the interactions between the ionised and molecular gas (as traced by CS (J = 5 - 4)), often (but not always) finding the HII region had cleared its immediate vicinity of molecules. Conclusions: Of our sample of nine, the observations of the two clusters expected to have the youngest HII regions (from previous radio observations) are suggestive of having infalling motions in the H29α emission, which could be indicative of late stage accretion onto the stars despite the presence of an HII region. Table A.2 is also available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130

40 CFR 1033.515 - Discrete-mode steady-state emission tests of locomotives and locomotive engines.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Discrete-mode steady-state emission... Procedures § 1033.515 Discrete-mode steady-state emission tests of locomotives and locomotive engines. This... a warm-up followed by a sequence of nominally steady-state discrete test modes, as described in...

Procedures and Standards for Residential Ventilation System Commissioning: An Annotated Bibliography

Energy Technology Data Exchange (ETDEWEB)

Stratton, J. Chris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wray, Craig P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2013-04-01

Beginning with the 2008 version of Title 24, new homes in California must comply with ANSI/ASHRAE Standard 62.2-2007 requirements for residential ventilation. Where installed, the limited data available indicate that mechanical ventilation systems do not always perform optimally or even as many codes and forecasts predict. Commissioning such systems when they are installed or during subsequent building retrofits is a step towards eliminating deficiencies and optimizing the tradeoff between energy use and acceptable IAQ. Work funded by the California Energy Commission about a decade ago at Berkeley Lab documented procedures for residential commissioning, but did not focus on ventilation systems. Since then, standards and approaches for commissioning ventilation systems have been an active area of work in Europe. This report describes our efforts to collect new literature on commissioning procedures and to identify information that can be used to support the future development of residential-ventilation-specific procedures and standards. We recommend that a standardized commissioning process and a commissioning guide for practitioners be developed, along with a combined energy and IAQ benefit assessment standard and tool, and a diagnostic guide for estimating continuous pollutant emission rates of concern in residences (including a database that lists emission test data for commercially-available labeled products).

Compound list: acetaminophen [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available acetaminophen APAP 00001 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/acetam...inophen.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/acetam...inophen.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/i...cedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/acetaminophen.Rat.in_vivo.Liver.Repeat.zip ftp...://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/acetaminophen.Rat.in_vivo.Kidn

Compound list: gentamicin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available gentamicin GMC 00147 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/gentam...icin.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/gentam...at/in_vivo/Liver/Repeat/gentamicin.Rat.in_vivo.Liver.Repeat.zip ftp://ftp.bioscie...ncedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/gentamicin.Rat.in_vivo.Kidney.Single.zip ftp...://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Repeat/gentamicin.Rat.in_vivo.Kidney.Repeat.zip ...

Compound list: carbon tetrachloride [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available carbon tetrachloride CCL4 00003 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LAT...EST/Human/in_vitro/carbon_tetrachloride.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tgg...ates/LATEST/Rat/in_vitro/carbon_tetrachloride.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open...-tggates/LATEST/Rat/in_vivo/Liver/Single/carbon_tetrachloride.Rat.in_vivo.Liver.S...ingle.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/carbon_tetrachloride.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: ketoconazole [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available ketoconazole KC 00047 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/ketoco...nazole.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/ketoco...nazole.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/ketoco...jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/ketoconazole.Rat.in_vivo.Liver.Repeat.zip ftp://ftp....biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/ketoconazole.Rat.in_vivo.Kidney.Singl

Compound list: cyclosporine A [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available cyclosporine A CSA 00142 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/cyclosporine..._A.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/cyclosporine.../in_vivo/Liver/Single/cyclosporine_A.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosc...iencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/cyclosporine_A.Rat.in_vivo.Liver.Repeat.zip... ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/cyclosporine_A.Rat.in_vivo

47 CFR 2.1511 - Measurements of radiated emissions.

Science.gov (United States)

2010-10-01

... TREATY MATTERS; GENERAL RULES AND REGULATIONS FCC Procedure for Testing Class A, B and S Emergency... 243 MHz. Step (9) Compute the peak effective radiated power for the maximum level of each measured emission using the following formula: EC03JN91.001 where: dBmmeas is the measured receiver reading in dBm...

75 FR 15645 - Approval and Promulgation of Air Quality Implementation Plans; Texas; Revisions to the Emission...

Science.gov (United States)

2010-03-30

... clarify EPA's role in the approval of emission quantification protocols. While the previous SIP- approved... approve severable portions of two revisions to the Texas State Implementation Plan (SIP) submitted by the... to further clarify procedures for using emission protocols and to update the approved list of...

Landfill operation and waste management procedures in the reduction of methane and leachate pollutant emissions from municipal solid waste landfills

Energy Technology Data Exchange (ETDEWEB)

Jokela, J.

2002-07-01

The objective of the present research was to find ways of minimising emissions from municipal solid waste (MSW) landfills by means of laboratory experiments. During anaerobic incubation for 237 days, the grey waste components produced between 120 and 320 m{sup 3}CH{sub 4} tTS{sup -1} and between 0.32 and 3.5 kg NH{sub 4}-N tTS{sup -1} and the first-order rate constant of degradation ranged from 0.021 and 0.058 d{sup -1}. High amounts of COD and NH{sub 4}-N were observed in the leachate of grey waste in all the procedures tested during lysimeter experiments lasting 573 days. In the 10- year-old landfilled MSW, a high rate of methanisation was achieved with rainwater addition and leachate recirculation over 538 days, whereas initially pre-wetted grey waste and landfilled MSW were rapidly acidified, thus releasing a high amount of COD into the leachate. In batch assays, the grey waste produced a methane potential amounting to 70-85 % of the total methane potential of the grey waste plus putrescibles. In low moisture conditions, i.e. below 55%, methane production was delayed in the old landfill waste and prevented in the grey waste. In the emission potential study with five waste types, putrescibles produced 410 m{sup 3}CH{sub 4} tTS{sup -1} and 3.6 kgNH{sub 4}-N tTS{sup -1}, whereas composted putrescibles produced 41 m{sup 3}CH{sub 4} tVS{sup -1}, and 2.0 kgNH{sub 4}-N tTS{sup -1}. The remains of putrescibles probably caused the leaching potential of 2.1 kgNH{sub 4}-N tTS{sup -1} in the grey waste. Aeration for 51 days in lysimeters reduced the CH{sub 4} potential of putrescibles by more than 68 % and of the lysimeter landfilled grey waste by 50 %, indicating the potential of aeration for CH4 emission reduction. Nitrogen removal of landfill leachate was studied in the laboratory as well as on-site. Over 90 % nitrification of leachate was obtained with loading rates between 100 and 130 mgNH{sub 4}-N l{sup -1} d-1 at 25 deg C. Nitrified leachate was denitrified with a

Safety Precautions and Operating Procedures in an (A)BSL-4 Laboratory: 4. Medical Imaging Procedures.

Science.gov (United States)

Byrum, Russell; Keith, Lauren; Bartos, Christopher; St Claire, Marisa; Lackemeyer, Matthew G; Holbrook, Michael R; Janosko, Krisztina; Barr, Jason; Pusl, Daniela; Bollinger, Laura; Wada, Jiro; Coe, Linda; Hensley, Lisa E; Jahrling, Peter B; Kuhn, Jens H; Lentz, Margaret R

2016-10-03

Medical imaging using animal models for human diseases has been utilized for decades; however, until recently, medical imaging of diseases induced by high-consequence pathogens has not been possible. In 2014, the National Institutes of Health, National Institute of Allergy and Infectious Diseases, Integrated Research Facility at Fort Detrick opened an Animal Biosafety Level 4 (ABSL-4) facility to assess the clinical course and pathology of infectious diseases in experimentally infected animals. Multiple imaging modalities including computed tomography (CT), magnetic resonance imaging, positron emission tomography, and single photon emission computed tomography are available to researchers for these evaluations. The focus of this article is to describe the workflow for safely obtaining a CT image of a live guinea pig in an ABSL-4 facility. These procedures include animal handling, anesthesia, and preparing and monitoring the animal until recovery from sedation. We will also discuss preparing the imaging equipment, performing quality checks, communication methods from "hot side" (containing pathogens) to "cold side," and moving the animal from the holding room to the imaging suite.

Emissions from laboratory combustor tests of manufactured wood products

Energy Technology Data Exchange (ETDEWEB)

Wilkening, R.; Evans, M.; Ragland, K. [Univ. of Wisconsin, Madison, WI (United States); Baker, A. [USDA Forest Products Lab., Madison, WI (United States)

1993-12-31

Manufactured wood products contain wood, wood fiber, and materials added during manufacture of the product. Manufacturing residues and the used products are burned in a furnace or boiler instead of landfilling. Emissions from combustion of these products contain additional compounds from the combustion of non-wood material which have not been adequately characterized to specify the best combustion conditions, emissions control equipment, and disposal procedures. Total hydrocarbons, formaldehyde, higher aldehydes and carbon monoxide emissions from aspen flakeboard and aspen cubes were measured in a 76 mm i.d. by 1.5 m long fixed bed combustor as a function of excess oxygen, and temperature. Emissions of hydrocarbons, aldehydes and CO from flakeboard and from clean aspen were very sensitive to average combustor temperature and excess oxygen. Hydrocarbon and aldehyde emissions below 10 ppM were achieved with 5% excess oxygen and 1,200{degrees}C average temperature for aspen flakeboard and 1,100{degrees}C for clean aspen at a 0.9 s residence time. When the average temperature decreased below these levels, the emissions increased rapidly. For example, at 950{degrees}C and 5% excess oxygen the formaldehyde emissions were over 1,000 ppM. These laboratory tests reinforce the need to carefully control the temperature and excess oxygen in full-scale wood combustors.

Newborn hearing screening with transient evoked otoacoustic emissions and automatic auditory brainstem response

Directory of Open Access Journals (Sweden)

Renata Mota Mamede de Carvallo

2008-09-01

Full Text Available Objective: The aim of the present investigation was to check Transient Evoked Otoacoustic Emissions and Automatic Auditory Brainstem Response tests applied together in regular nurseries and Newborn Intensive Care Units (NICU, as well as to describe and compare the results obtained in both groups. Methods: We tested 150 newborns from regular nurseries and 70 from NICU. Rresults: The newborn hearing screening results using Transient Evoked Otoacoustic Emissions and Automatic Auditory Brainstem Response tests could be applied to all babies. The “pass” result for the group of babies from the nursery was 94.7% using Transient Evoked Otoacoustic Emissions and 96% using Automatic Auditory Brainstem Response. The newborn intensive care unit group obtained 87.1% on Transient Evoked Otoacoustic Emissions and 80% on the Automatic Auditory Brainstem Response, and there was no statistical difference between the procedures when the groups were evaluated individually. However, comparing the groups, Transient Evoked Otoacoustic Emissions were presented in 94.7% of the nursery babies and in 87.1% in the group from the newborn intensive care unit. Considering the Automatic Auditory Brainstem Response, we found 96 and 87%, respectively. Cconclusions: Transient Evoked Otoacoustic Emissions and Automatic Auditory Brainstem Response had similar “pass” and “fail” results when the procedures were applied to neonates from the regular nursery, and the combined tests were more precise to detect hearing impairment in the newborn intensive care unit babies.

Dark clouds in the vicinity of the emission nebula Sh2-205: interstellar extinction and distances

Science.gov (United States)

Straižys, V.; Čepas, V.; Boyle, R. P.; Zdanavičius, J.; Maskoliūnas, M.; Kazlauskas, A.; Zdanavičius, K.; Černis, K.

2016-05-01

Results of CCD photometry in the seven-colour Vilnius system for 922 stars down to V = 16-17 mag and for 302 stars down to 19.5 mag are used to investigate the interstellar extinction in an area of 1.5 square degrees in the direction of the P7 and P8 clumps of the dark cloud TGU H942, which lies in the vicinity of the emission nebula Sh2-205. In addition, we used 662 red clump giants that were identified by combining the 2MASS and WISE infrared surveys. The resulting plots of extinction versus distance were compared with previous results of the distribution and radial velocities of CO clouds and with dust maps in different passbands of the IRAS and WISE orbiting observatories. A possible distance of the front edge of the nearest cloud layer at 130 ± 10 pc was found. This dust layer probably covers all the investigated area, which results in extinction of up to 1.8 mag in some directions. A second rise of the extinction seems to be present at 500-600 pc. Within this layer, the clumps P7 and P8 of the dust cloud TGU H942, the Sh2-205 emission nebula, and the infrared cluster FSR 655 are probably located. In the direction of these clouds, we identified 88 young stellar objects and a new infrared cluster. Full Tables 1 and 2 are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/590/A21

GAME: GAlaxy Machine learning for Emission lines

Science.gov (United States)

Ucci, G.; Ferrara, A.; Pallottini, A.; Gallerani, S.

2018-06-01

We present an updated, optimized version of GAME (GAlaxy Machine learning for Emission lines), a code designed to infer key interstellar medium physical properties from emission line intensities of ultraviolet /optical/far-infrared galaxy spectra. The improvements concern (a) an enlarged spectral library including Pop III stars, (b) the inclusion of spectral noise in the training procedure, and (c) an accurate evaluation of uncertainties. We extensively validate the optimized code and compare its performance against empirical methods and other available emission line codes (PYQZ and HII-CHI-MISTRY) on a sample of 62 SDSS stacked galaxy spectra and 75 observed HII regions. Very good agreement is found for metallicity. However, ionization parameters derived by GAME tend to be higher. We show that this is due to the use of too limited libraries in the other codes. The main advantages of GAME are the simultaneous use of all the measured spectral lines and the extremely short computational times. We finally discuss the code potential and limitations.

GAME: GAlaxy Machine learning for Emission lines

Science.gov (United States)

Ucci, G.; Ferrara, A.; Pallottini, A.; Gallerani, S.

2018-03-01

We present an updated, optimized version of GAME (GAlaxy Machine learning for Emission lines), a code designed to infer key interstellar medium physical properties from emission line intensities of UV/optical/far infrared galaxy spectra. The improvements concern: (a) an enlarged spectral library including Pop III stars; (b) the inclusion of spectral noise in the training procedure, and (c) an accurate evaluation of uncertainties. We extensively validate the optimized code and compare its performance against empirical methods and other available emission line codes (pyqz and HII-CHI-mistry) on a sample of 62 SDSS stacked galaxy spectra and 75 observed HII regions. Very good agreement is found for metallicity. However, ionization parameters derived by GAME tend to be higher. We show that this is due to the use of too limited libraries in the other codes. The main advantages of GAME are the simultaneous use of all the measured spectral lines, and the extremely short computational times. We finally discuss the code potential and limitations.

Compound list: valproic acid [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available valproic acid VPA 00005 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/valpr...oic_acid.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/valpr...oic_acid.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/valpr...edbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/valproic_acid.Rat.in_vivo.Liver.Repeat.zip ftp:...//ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/valproic_acid.Rat.in_vivo.Kidne

Compound list: allyl alcohol [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available allyl alcohol AA 00010 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/allyl_alcohol....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/allyl_alcohol...dbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/allyl_alcohol.Rat.in_vivo.Liver.Repeat.zip ftp:/.../ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Single/allyl_alcohol.Rat.in_vivo.Kidney....Single.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Kidney/Repeat/allyl_alcohol.Rat.in_vivo.Kidney.Repeat.zip ...

75 FR 27647 - Approval and Promulgation of Air Quality Implementation Plans; Texas; Revisions to the Emission...

Science.gov (United States)

2010-05-18

... severable portions of two revisions to the Texas State Implementation Plan (SIP) submitted by the State of... further clarify procedures for using emission protocols and to update the approved list of emission credit... to recently recodified 30 TAC Chapter 117 provisions. EPA has determined that these SIP revisions...

Monitoring, reporting and verifying emissions in the climate economy

Science.gov (United States)

Bellassen, Valentin; Stephan, Nicolas; Afriat, Marion; Alberola, Emilie; Barker, Alexandra; Chang, Jean-Pierre; Chiquet, Caspar; Cochran, Ian; Deheza, Mariana; Dimopoulos, Christopher; Foucherot, Claudine; Jacquier, Guillaume; Morel, Romain; Robinson, Roderick; Shishlov, Igor

2015-04-01

The monitoring, reporting and verification (MRV) of greenhouse-gas emissions is the cornerstone of carbon pricing and management mechanisms. Here we consider peer-reviewed articles and 'grey literature' related to existing MRV requirements and their costs. A substantial part of the literature is the regulatory texts of the 15 most important carbon pricing and management mechanisms currently implemented. Based on a comparison of key criteria such as the scope, cost, uncertainty and flexibility of procedures, we conclude that conventional wisdom on MRV is not often promoted in existing carbon pricing mechanisms. Quantification of emissions uncertainty and incentives to reduce this uncertainty are usually only partially applied, if at all. Further, the time and resources spent on small sources of emissions would be expected to be limited. Although provisions aiming at an effort proportionate to the amount of emissions at stake -- 'materiality' -- are widespread, they are largely outweighed by economies of scale: in all schemes, MRV costs per tonne are primarily driven by the size of the source.

Motivational power of future time perspective : Meta-analyses in education, work, and health

NARCIS (Netherlands)

Andre, L.; van Vianen, A.E.M.; Peetsma, T.T.D.; Oort, F.J.

2018-01-01

Future time perspective (FTP) may predict individual attitudes and behaviors. However, FTP research includes different FTP conceptualizations and outcomes which hinder generalizing its findings. To solve the inconsistencies in FTP research and generalize the magnitude of FTP as a driver of

Compound list: TNFα [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available TNFα TNF 00A08 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitr...o/TNFa.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/TNFa.Rat....in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/TNFa.Rat.in_vivo.Liver.Single.zip ...

Compound list: LPS [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available LPS LPS 00A07 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro.../LPS.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/LPS.Rat.in..._vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/LPS.Rat.in_vivo.Liver.Single.zip ...

Compound list: galactosamine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available galactosamine GaN 00A06 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/galactosamine....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/galactosamine....Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/galactosamine.Rat.in_vivo.Liver.Single.zip ...

Compound list: cyclophosphamide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available cyclophosphamide CPA 00024 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/H...uman/in_vitro/cyclophosphamide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATE...ST/Rat/in_vitro/cyclophosphamide.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATE...ST/Rat/in_vivo/Liver/Single/cyclophosphamide.Rat.in_vivo.Liver.Single.zip ftp://f...tp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/cyclophosphamide.Rat.in_vivo.Liver.

NWCF Evaporator Tank System 2001 Offgas Emissions Inventory; ANNUAL

International Nuclear Information System (INIS)

Boardman, R.D.; Lamb, K.M.; Matejka, L.A.; Nenni, J.A.

2002-01-01

An offgas emissions inventory and liquid stream characterization of the Idaho New Waste Calcining Facility (NWCF) Evaporator Tank System (ETS), formerly known as the High Level Liquid Waste Evaporator (HLLWE), has been completed. The emissions rates of volatile and semi-volatile organic compounds, multiple metals, particulate, and hydrochloric acid were measured in accordance with an approved Quality Assurance Project Plan (QAPjP) and Test Plan that invoked U.S. Environmental Protection Agency (EPA) standard sample collection and analysis procedures. Offgas samples were collected during the start up and at the end of evaporator batches when it was hypothesized the emissions would be at peak rates. Corresponding collection of samples from the evaporator feed overhead condensate, and bottoms was made at approximately the same time as the emissions inventory to support material balance determinations for the evaporator process. The data indicate that organic compound emissions are slightly higher at the beginning of the batch while metals emissions, including mercury, are slightly higher at the end of the evaporator batch. The maximum emissions concentrations are low for all constituents of primary concern. Mercury emissions were less than 5 ppbv, while the sum of HCl and Cl2 emissions was less than 1 ppmv. The sum of all organic emissions also was less than 1 ppmv. The estimated hazardous quotient (HQ) for the evaporator was 6.2e-6 as compared to 0.25 for the EPA target criteria. The cancer risk was 1.3e-10 compared to an EPA target of le-5

Vehicle emission factors of solid nanoparticles in the laboratory and on the road using Portable Emission Measurement Systems (PEMS

Directory of Open Access Journals (Sweden)

Barouch eGiechaskiel

2015-12-01

due to the different DPF fill state and passive regeneration during the tests. The findings of this study can (i help improving the on SPN emissions and (ii assist policy makers in designing effective test procedures for measuring SPN emissions of vehicles under real-world driving conditions.

Multi-year remote-sensing measurements of gasoline light-duty vehicle emissions on a freeway ramp

International Nuclear Information System (INIS)

Sjoedin, A.; Andreasson, K.

2000-01-01

On-road optical remote-sensing measurements of gasoline light-duty vehicle (LDV) emissions - CO, HC, NO - were conducted on a freeway ramp in Gothenburg, Sweden, in 1991, 1995 and 1998. Based on almost 30,000 emission measurements, the results show that both catalyst cars and non-catalyst cars emissions deteriorate over time, but also that the emission performance of new TWC-cars has improved significantly in recent years. Furthermore, it was found that fleet age rather than model year determines the rate of emission deterioration for TWC-cars for both CO and NO. The study demonstrates that remote sensing may constitute a powerful tool to evaluate real-world LDV emissions; however, daily field calibration procedures need to be developed in order to assure that the evolution in fleet average emissions can be accurately measured. (author)

Compound list: chloramphenicol [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available chloramphenicol CMP 00064 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/chlorampheni...col.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST...Rat/in_vivo/Liver/Single/chloramphenicol.Rat.in_vivo.Liver.Single.zip ftp://ftp.b...iosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/chloramphenicol.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: diethyl maleate [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available diethyl maleate DEM 00A05 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/diethyl_male.../Rat/in_vitro/diethyl_maleate.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/diethyl_maleate.Rat.in_vivo.Liver.Single.zip ... ...ate.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST

Compound list: buthionine sulfoximine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available buthionine sulfoximine BSO 00A04 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LA...TEST/Human/in_vitro/buthionine_sulfoximine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-...tggates/LATEST/Rat/in_vitro/buthionine_sulfoximine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive.../open-tggates/LATEST/Rat/in_vivo/Liver/Single/buthionine_sulfoximine.Rat.in_vivo.Liver.Single.zip ...

Compound list: chlorpromazine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available chlorpromazine CPZ 00016 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Hum...an/in_vitro/chlorpromazine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/R.../in_vivo/Liver/Single/chlorpromazine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosc...iencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/chlorpromazine.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: clomipramine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available clomipramine CPM 00121 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/clomipramine....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/clomipramine...vo/Liver/Single/clomipramine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc....jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/clomipramine.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: promethazine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available promethazine PMZ 00110 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/promethazine....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/promethazine...vo/Liver/Single/promethazine.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc....jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/promethazine.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: penicillamine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available penicillamine PEN 00099 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/penicillamine....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/penicillamine..._vivo/Liver/Single/penicillamine.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscienc...edbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/penicillamine.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: glibenclamide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available glibenclamide GBC 00042 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/glibenclam...ide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/glibenclam..._vivo/Liver/Single/glibenclamide.Rat.in_vivo.Liver.Single.zip ftp://ftp.bioscienc...edbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/glibenclamide.Rat.in_vivo.Liver.Repeat.zip ...

A comparison of emission calculations using different modeled indicators with 1-year online measurements.

Science.gov (United States)

Lengers, Bernd; Schiefler, Inga; Büscher, Wolfgang

2013-12-01

The overall measurement of farm level greenhouse gas (GHG) emissions in dairy production is not feasible, from either an engineering or administrative point of view. Instead, computational model systems are used to generate emission inventories, demanding a validation by measurement data. This paper tests the GHG calculation of the dairy farm-level optimization model DAIRYDYN, including methane (CH₄) from enteric fermentation and managed manure. The model involves four emission calculation procedures (indicators), differing in the aggregation level of relevant input variables. The corresponding emission factors used by the indicators range from default per cow (activity level) emissions up to emission factors based on feed intake, manure amount, and milk production intensity. For validation of the CH₄ accounting of the model, 1-year CH₄ measurements of an experimental free-stall dairy farm in Germany are compared to model simulation results. An advantage of this interdisciplinary study is given by the correspondence of the model parameterization and simulation horizon with the experimental farm's characteristics and measurement period. The results clarify that modeled emission inventories (2,898, 4,637, 4,247, and 3,600 kg CO₂-eq. cow(-1) year(-1)) lead to more or less good approximations of online measurements (average 3,845 kg CO₂-eq. cow(-1) year(-1) (±275 owing to manure management)) depending on the indicator utilized. The more farm-specific characteristics are used by the GHG indicator; the lower is the bias of the modeled emissions. Results underline that an accurate emission calculation procedure should capture differences in energy intake, owing to milk production intensity as well as manure storage time. Despite the differences between indicator estimates, the deviation of modeled GHGs using detailed indicators in DAIRYDYN from on-farm measurements is relatively low (between -6.4% and 10.5%), compared with findings from the literature.

Speciation of mercury compounds by gas chromatography with atomic emission detection. Simultaneous optimization of a headspace solid-phase microextraction and derivatization procedure by use of chemometric techniques

Energy Technology Data Exchange (ETDEWEB)

Carro, A.M.; Neira, I.; Rodil, R.; Lorenzo, R. A. [Univ. Santiago de Compostela (Spain). Dpto. Quimica Analitica, Nutricion y Bromatologia

2003-06-01

A method is proposed for the extraction and determination of organomercury compounds and Hg(II) in seawater samples by headspace solid-phase microextraction (HS-SPME) combined with capillary gas chromatography-microwave-induced plasma atomic emission spectrometry. The mercury species were derivatized with sodium tetraphenylborate, sorbed on a polydimethylsiloxane-coated fused-silica fibre, and desorbed in the injection port of the GC, in splitless mode. Experimental design methodology was used to evaluate the effect of six HS-SPME-derivatization variables: sample volume, NaBPh{sub 4} volume, pH, sorption time, extraction-derivatization temperature, and rate of stirring. Use of a multicriterion decision-making approach, with the desirability function, enabled determination of the optimum working conditions of the procedure for simultaneous analysis of three mercury species. (orig.)

Emissions of gaseous nitrogen species from manure management: A new approach

International Nuclear Information System (INIS)

Daemmgen, Ulrich; Hutchings, Nicholas J.

2008-01-01

A procedure for the assessment of emissions of nitrogen (N) species (ammonia, nitrous oxide, nitric oxide, di-nitrogen) from the manure management system is developed, which treats N pools and flows including emissions strictly according to conservation of mass criteria. As all relevant flows in the husbandry of mammals are depicted, the methodology is considered a Tier 3 approach in IPCC terminology or a detailed methodology in UN ECE terminology. The importance of accounting for all N species is illustrated by comparing emission estimates obtained using this approach with those obtained from the application the present detailed/Tier 2 methodology. - A cow is a cow. There is no distinction between an IPCC and a UN ECE cow!

Emissions of gaseous nitrogen species from manure management: A new approach

Energy Technology Data Exchange (ETDEWEB)

Daemmgen, Ulrich [Federal Agricultural Research Centre, Institute of Agroecology, Bundesallee 50, 38116 Braunschweig (Germany)], E-mail: ulrich.daemmgen@fal.de; Hutchings, Nicholas J. [Danish Institute of Agricultural Sciences, Department of Agroecology, Tjele (Denmark)], E-mail: nick.hutchings@agrsci.dk

2008-08-15

A procedure for the assessment of emissions of nitrogen (N) species (ammonia, nitrous oxide, nitric oxide, di-nitrogen) from the manure management system is developed, which treats N pools and flows including emissions strictly according to conservation of mass criteria. As all relevant flows in the husbandry of mammals are depicted, the methodology is considered a Tier 3 approach in IPCC terminology or a detailed methodology in UN ECE terminology. The importance of accounting for all N species is illustrated by comparing emission estimates obtained using this approach with those obtained from the application the present detailed/Tier 2 methodology. - A cow is a cow. There is no distinction between an IPCC and a UN ECE cow{exclamation_point}.

Compound list: haloperidol [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available haloperidol HPL 00036 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/haloperidol....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/haloperidol....Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/haloperidol...archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/haloperidol.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: methylene dianiline [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available methylene dianiline DAPM 00155 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/methyle...es/LATEST/Rat/in_vivo/Liver/Single/methylene_dianiline.Rat.in_vivo.Liver.Single.zip ftp://ftp.biosciencedbc....jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/methylene_dianiline.Rat.in_vivo.Liver.Repeat.zip ... ...ne_dianiline.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggat

Compound list: butylated hydroxyanisole [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available butylated hydroxyanisole BHA 00156 ftp://ftp.biosciencedbc.jp/archive/open-tggates/...LATEST/Human/in_vitro/butylated_hydroxyanisole.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/o...pen-tggates/LATEST/Rat/in_vivo/Liver/Single/butylated_hydroxyanisole.Rat.in_vivo.Liver.Single.zip ftp://ftp....biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/butylated_hydroxyanisole.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: diltiazem [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available diltiazem DIL 00092 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/diltia...zem.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/diltia...zem.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/diltia...open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/diltiazem.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: flutamide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available flutamide FT 00044 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/flutam...ide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/flutam...ide.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/flutam...pen-tggates/LATEST/Rat/in_vivo/Liver/Repeat/flutamide.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: tamoxifen [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available tamoxifen TMX 00054 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/tam...oxifen.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/tam...oxifen.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/tam...open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/tamoxifen.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: acetamidofluorene [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available acetamidofluorene AAF 00144 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/acetam...idofluorene.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/acetam...ATEST/Rat/in_vivo/Liver/Single/acetamidofluorene.Rat.in_vivo.Liver.Single.zip ftp...://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/acetamidofluorene.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: fluoxetine hydrochloride [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available fluoxetine hydrochloride FLX 00158 ftp://ftp.biosciencedbc.jp/archive/open-tggates/...LATEST/Human/in_vitro/fluoxetine_hydrochloride.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/o...pen-tggates/LATEST/Rat/in_vivo/Liver/Single/fluoxetine_hydrochloride.Rat.in_vivo.Liver.Single.zip ftp://ftp....biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/fluoxetine_hydrochloride.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: papaverine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available papaverine PAP 00098 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/papaverine.Human.in_vitro.Liver.zip ftp://ftp....biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/papa...verine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/papa...ive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/papaverine.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: gemfibrozil [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available gemfibrozil GFZ 00031 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/gemfibrozil....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/gemfibrozil....Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/gemfibrozil...archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/gemfibrozil.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: diazepam [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available diazepam DZP 00023 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/diaz...epam.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/diaz...epam.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/diaz...-tggates/LATEST/Rat/in_vivo/Liver/Repeat/diazepam.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: terbinafine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available terbinafine TBF 00123 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/terbinafine....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/terbinafine....Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/terbinafine...archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/terbinafine.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: coumarin [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available coumarin CMA 00027 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/coumari...n.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/coumari...n.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/coumari...-tggates/LATEST/Rat/in_vivo/Liver/Repeat/coumarin.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: triazolam [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available triazolam TZM 00120 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/triazolam.Human.in_vitro.Liver.zip ftp://ftp.bi...osciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/triazolam....Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/triazolam...open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/triazolam.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: fluphenazine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available fluphenazine FP 00037 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/flu...phenazine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/flu...phenazine.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/flu...jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/fluphenazine.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: amitriptyline [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available amitriptyline AMT 00070 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/amit...riptyline.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/amit...riptyline.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/amit...edbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/amitriptyline.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: furosemide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available furosemide FUR 00078 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/furose...mide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/furose...mide.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/furose...ive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/furosemide.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: benzbromarone [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available benzbromarone BBr 00021 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/benz...bromarone.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/benz...bromarone.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/benz...edbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/benzbromarone.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: vitamin A [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available vitamin A VA 00059 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/vitam...in_A.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/vitam...in_A.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/vitam...pen-tggates/LATEST/Rat/in_vivo/Liver/Repeat/vitamin_A.Rat.in_vivo.Liver.Repeat.zip ...

Compound list: tolbutamide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available tolbutamide TLB 00114 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/tolbutam...ide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/tolbutam...ide.Rat.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/tolbutam...archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/tolbutamide.Rat.in_vivo.Liver.Repeat.zip ...

40 CFR 63.9915 - What test methods and other procedures must I use to demonstrate initial compliance with dioxin...

Science.gov (United States)

2010-07-01

... must I use to demonstrate initial compliance with dioxin/furan emission limits? 63.9915 Section 63.9915....9915 What test methods and other procedures must I use to demonstrate initial compliance with dioxin... limit for dioxins/furans in Table 1 to this subpart, you must follow the test methods and procedures...

Utilization of atomic emission spectroscopy methods for determination of rare earth elements

International Nuclear Information System (INIS)

Kubova, J.; Polakovicova, J.; Medved, J.; Stresko, V.

1997-01-01

The authors elaborated and applied procedures for rare earth elements (REE) determination using optical emission spectrograph with D.C arc excitation and ICP atomic emission spectrometry.Some of these analytical method are described. The proposed procedure was applied for the analysis of different types of geological materials from several Slovak localities. The results the REE determination were used for e.g. investigation of REE distribution in volcanic rocks, rhyolite tuffs with uranium-molybdenum mineralization, sandstones with heavy minerals accumulations, phosphatic sandstones, granites, quartz-carbonate veins and in the meteorite found in the locality Rumanova. The REE contents were determined in 19 mineral water sources and the results obtained by the both mentioned methods compared. The total REE contents in the analysed mineral water samples were between 2 · 10 -7 and 3 · 10 -5 g dm -3

Assessment of the strengths and weaknesses of the new Real Driving Emissions (RDE) test procedure

NARCIS (Netherlands)

Cuelenaere, R.F.A.; Ligterink, N.E.

2016-01-01

Door Dieselgate is er hernieuwde aandacht voor de luchtverontreinigende uitlaatgassen van auto’s, in het bijzonder voor de hoge NOx praktijkemissies van moderne Euro-5 en Euro-6 personenauto’s en bestelwagens. De ontwikkeling van nieuwe Europese Real Driving Emissions (RDE) wetgeving wordt gezien

Prediction of impurity spectral emission in plasmas

International Nuclear Information System (INIS)

Gordon, H.; Summers, H.P.

1985-01-01

This paper summarises the development of a set of general purpose computational procedures for the prediction of spectral emission from plasmas, with emphasis on fusion plasmas. The first stage was concerned with the calculation of populations of low levels of impurity ions in a statistical balance approximation in thermal plasmas of arbitrary electron and proton temperatures and densities. This was merged with associated calculations of ionisation stage abundances in equilibrium, time dependent and spatially inhomogeneous conditions to yield spectrum line emissivities of direct relevance for comparative and diagnostic studies of observed spectra. The integrated computer program package draws upon sets or basic atomic data. In the present work the compilation of this basic data is adressed. A set of computer programs has beeen developed and used to convert systematically atomic rate data, drawn from the literature, to standard forms and parameter ranges. Regularities in this data along isoelectronic sequences are exploited to infer rates for an arbitrary ion from a set of representative data (termed the 'general Z' database). From this, the input for the spectral prediction codes above is generated. Presently data in the H, He, Li and Be isoelectronic sequences is prepared. The operation of the procedures is illustrated. (orig.)

Thermoluminescence emission spectra and optical bleaching of oligoclase

International Nuclear Information System (INIS)

Bos, A.J.J.; Piters, T.M.; Ypma, P.J.

1994-01-01

Thermoluminescence (TL) spectra of oligoclase samples have been recorded in the temperature range from 300 to 700 K and the wavelength range from 300 to 850 nm. Like other feldspars, oligoclase produces blue (peaking at 460 nm) and red (peaking at 765 nm) emission bands. The maximum of the red emission occurs 20 K lower than that of the blue band. Optical bleaching was performed at wavelengths varying from 360 to 800 nm. Bleaching of artificially irradiated oligoclase causes a decrease of the TL signal. The bleaching efficiency increases with decreasing wavelength. Bleaching does not only influence the height of the glow curve but also the shape. An interesting observation is that the ratio of the blue and red band intensities is not affected by a bleaching procedure. No evidence has been found that bleaching influences the shape of the emission spectra. The correlation between the blue and red bands is discussed. (Author)

Optimization of performance, emission, friction and wear characteristics of palm and Calophyllum inophyllum biodiesel blends

International Nuclear Information System (INIS)

Mosarof, M.H.; Kalam, M.A.; Masjuki, H.H.; Alabdulkarem, Abdullah; Ashraful, A.M.; Arslan, A.; Rashedul, H.K.; Monirul, I.M.

2016-01-01

Highlights: • All of biodiesel blends were given higher BSFC than diesel fuel, except for CIB10. • Diesel produces higher BP and BTE as compared to PB and CIB blends. • CO and HC emissions of PB blends were reduced more than diesel and CIB blends. • PB blends contained lower metal compositions compared to diesel and CIB blends. • PB20 showed lower worn scar surfaces area compared to diesel and biodiesel blends. - Abstract: A running automobile engine produces more friction and wear between its sliding components than an idle one, and thus requires lubrication to reduce this frictional effect. Biodiesel is an alternative diesel fuel that is produced from renewable resources. Energy studies conducted over the last two decades focused on solutions to problems of rising fossil fuel price, increasing dependency on foreign energy sources, and worsening environmental concerns. Palm oil biodiesel is mostly used in Malaysia. This study conducted engine performance and emission tests with a single-cylinder diesel engine fueled with palm and Calophyllum inophyllum biodiesel blends (PB10, PB20, PB30, CIB10, CIB20, and CIB30) at a full-load engine speed range of 1000–2400 rpm, and then compared the results with those of diesel fuel. Friction and wear tests were conducted using the four-ball tester with different temperatures at 40 and 80 kg load conditions and a constant speed of 1800 rpm. The average brake specific fuel consumption increased from 7.96% to 10.15% while operating on 10%, 20%, and 30% blends of palm and C. inophyllum biodiesel. The respective average brake powers for PB20 and PB30 were 9.31% and 12.93% lower compared with that for diesel fuel. PB20 produced relatively lower CO and HC emissions than the diesel and biodiesel blends. Diesel produced low amounts of NO_X emission, and the CIB blend produced a lower frictional coefficient compared with the diesel and PB blends. PB30 showed high average FTP and low average WSD, both of which enhanced

An Improved Cuckoo Search for a Patient Transportation Problem with Consideration of Reducing Transport Emissions

Directory of Open Access Journals (Sweden)

Liyang Xiao

2018-03-01

Full Text Available Many government agencies and business organizations have realized that it is necessary to consider not only the economic cost but also the road transport emissions when they determine the transport policies and operations. In this study, a patient transportation problem with the aim of reducing transport emissions has been formulated by implementing CVRP model. In order to determine the routes of patient transportation with optimized emissions for targeted hospital, an improved Cuckoo Search (ICS algorithm is proposed. In this study, a ‘split’ procedure has been implemented to simplify the individual’s representation. A new category of cuckoos has been introduced to improve the ICS’s search ability. Two heuristics have been applied to improve the quality of initial population. A local search mechanism has been embedded in the search procedure to improve the quality of solutions obtained at the end of each iteration. The computational results were encouraging and demonstrated the effectiveness of the proposed solution method.

Attributing land-use change carbon emissions to exported biomass

International Nuclear Information System (INIS)

Saikku, Laura; Soimakallio, Sampo; Pingoud, Kim

2012-01-01

In this study, a simple, transparent and robust method is developed in which land-use change (LUC) emissions are retrospectively attributed to exported biomass products based on the agricultural area occupied for the production. LUC emissions account for approximately one-fifth of current greenhouse gas emissions. Increasing agricultural exports are becoming an important driver of deforestation. Brazil and Indonesia are used as case studies due to their significant deforestation in recent years. According to our study, in 2007, approximately 32% and 15% of the total agricultural land harvested and LUC emissions in Brazil and Indonesia respectively were due to exports. The most important exported single items with regard to deforestation were palm oil for Indonesia and bovine meat for Brazil. To reduce greenhouse gas (GHG) emissions effectively worldwide, leakage of emissions should be avoided. This can be done, for example, by attributing embodied LUC emissions to exported biomass products. With the approach developed in this study, controversial attribution between direct and indirect LUC and amortization of emissions over the product life cycle can be overcome, as the method operates on an average basis and annual level. The approach could be considered in the context of the UNFCCC climate policy instead of, or alongside with, other instruments aimed at reducing deforestation. However, the quality of the data should be improved and some methodological issues, such as the allocation procedure in multiproduct systems and the possible dilution effect through third parties not committed to emission reduction targets, should be considered. - Highlights: ► CO 2 emissions from land use changes are highly important. ► Attribution of land use changes for products is difficult. ► Simple and robust method is developed to attribute land use change emissions.

Attributing land-use change carbon emissions to exported biomass

Energy Technology Data Exchange (ETDEWEB)

Saikku, Laura, E-mail: laura.saikku@helsinki.fi [University of Helsinki, P.O Box 65, 00014 University of Helsinki (Finland); Soimakallio, Sampo, E-mail: sampo.soimakallio@vtt.fi [VTT Technical Research Centre of Finland, P.O. Box 1000, 02044 VTT (Finland); Pingoud, Kim, E-mail: kim.pingoud@vtt.fi [VTT Technical Research Centre of Finland, P.O. Box 1000, 02044 VTT (Finland)

2012-11-15

In this study, a simple, transparent and robust method is developed in which land-use change (LUC) emissions are retrospectively attributed to exported biomass products based on the agricultural area occupied for the production. LUC emissions account for approximately one-fifth of current greenhouse gas emissions. Increasing agricultural exports are becoming an important driver of deforestation. Brazil and Indonesia are used as case studies due to their significant deforestation in recent years. According to our study, in 2007, approximately 32% and 15% of the total agricultural land harvested and LUC emissions in Brazil and Indonesia respectively were due to exports. The most important exported single items with regard to deforestation were palm oil for Indonesia and bovine meat for Brazil. To reduce greenhouse gas (GHG) emissions effectively worldwide, leakage of emissions should be avoided. This can be done, for example, by attributing embodied LUC emissions to exported biomass products. With the approach developed in this study, controversial attribution between direct and indirect LUC and amortization of emissions over the product life cycle can be overcome, as the method operates on an average basis and annual level. The approach could be considered in the context of the UNFCCC climate policy instead of, or alongside with, other instruments aimed at reducing deforestation. However, the quality of the data should be improved and some methodological issues, such as the allocation procedure in multiproduct systems and the possible dilution effect through third parties not committed to emission reduction targets, should be considered. - Highlights: Black-Right-Pointing-Pointer CO{sub 2} emissions from land use changes are highly important. Black-Right-Pointing-Pointer Attribution of land use changes for products is difficult. Black-Right-Pointing-Pointer Simple and robust method is developed to attribute land use change emissions.

Radio polarization and magnetic field structure in M 101

Science.gov (United States)

Berkhuijsen, E. M.; Urbanik, M.; Beck, R.; Han, J. L.

2016-04-01

We observed total and polarized radio continuum emission from the spiral galaxy M 101 at λλ 6.2 cm and 11.1 cm with the Effelsberg telescope. The angular resolutions are 2.´ 5 (=5.4 kpc) and 4.´ 4 (=9.5 kpc), respectively. We use these data to study various emission components in M 101 and properties of the magnetic field. Separation of thermal and non-thermal emission shows that the thermal emission is closely correlated with the spiral arms, while the non-thermal emission is more smoothly distributed indicating diffusion of cosmic ray electrons away from their places of origin. The radial distribution of both emissions has a break near R = 16 kpc (=7.´ 4), where it steepens to an exponential scale length of L ≃ 5 kpc, which is about 2.5 times smaller than at Rchange in the structure of M 101 takes place, which also affects the distributions of the strength of the random and ordered magnetic field. Beyond R = 16 kpc the radial scale length of both fields is about 20 kpc, which implies that they decrease to about 0.3 μG at R = 70 kpc, which is the largest optical extent. The equipartition strength of the total field ranges from nearly 10 μG at Rmechanism. We show that energetic events causing H I shells of mean diameter pitch angles that are about 8° larger than those of H I filaments. Based on observations with the 100 m telescope of the MPIfR at Effelsberg.FITS files of the images are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (ftp://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/588/A114

Sample preparation procedure for PIXE elemental analysis on soft tissues

International Nuclear Information System (INIS)

Kubica, B.; Kwiatek, W.M.; Dutkiewicz, E.M.; Lekka, M.

1997-01-01

Trace element analysis is one of the most important field in analytical chemistry. There are several instrumental techniques which are applied for determinations of microscopic elemental content. The PIXE (Proton Induced X-ray Emission) technique is one of the nuclear techniques that is commonly applied for such purpose due to its multielemental analysis possibilities. The aim of this study was to establish the optimal conditions for target preparation procedure. In this paper two different approaches to the topic are presented and widely discussed. The first approach was the traditional pellet technique and the second one was mineralization procedure. For the analysis soft tissue such as liver was used. Some results are also presented on water samples. (author)

Significance of agricultural row structure on the microwave emissivity of soils

Science.gov (United States)

Promes, P. M.; Jackson, T. J.; O'Neill, P. E.

1987-01-01

A series of field experiments was carried out to extend the data base available for verifying agricultural row effect models of emissivity. The row effects model was used to simulate a data base from which an algorithm could be developed to account for row effects when the scene dielectric constant and small-scale roughness are unknown. One objective of the study was to quantify the significance of row structure and to develop a practical procedure for removing the effects of periodic row structure on the microwave emissivity of a soil in order to use the emissivity values to estimate the soil moisture. A second objective was to expand the data set available for model verification through field observations using a truck-mounted 1.4-GHz microwave radiometer.

Clinical impact of 18F-fluorodeoxyglucose positron emission tomography in the diagnosis of neurological diseases

International Nuclear Information System (INIS)

Buck, A.; Kamel, E.

2002-01-01

In this review it will be discussed in which neurological disorders positron emission tomography can yield important diagnostic information. Because positron emission tomography is an expensive method indications have to be cleary defined. One important question concerns the differentiation of tumor recurrence and scar due to radiation therapy or an operation. The grading of brain tumors is another application. In HIV patients fluorodeoxyglucose positron emission tomography can separate lymphoma and toxoplasmosis. In the evaluation of dementia positron emission tomography can help to clarify the differential diagnosis. Another important area is the presurgical evaluation of epilepsy patients and patients with cerebrovascular disease in whom a surgical revascularization procedure is planned. In extrapyramidal disorders, positron emission tomography can often help to establish the final diagnosis. (author)

WP/073 Is the Clean Development Mechanism Effective for Emission Reductions?

DEFF Research Database (Denmark)

Huang, Yongfu; He, Jingjing; Tarp, Finn

makes use of the newly-developed econometric methods for dynamic panel data models associated with X-differencing procedure. It provides evidence in support of a decline in CO2 emissions in the CDM host countries. It has important policy implications that encourage the international community to support...

Quantifying Nanoparticle Release from Nanotechnology: Scientific Operating Procedure Series: SOP C 3

Science.gov (United States)

2017-02-01

5.2.1). It should be noted that the steps outlined in this procedure do not necessarily need to be performed in order; the reader is directed to...ICP-MS) or atomic emission spectroscopy (ICP-AES) should be performed on an acid- digested sample to test for the presence of those elements known to

Impact of cold temperature on Euro 6 passenger car emissions.

Science.gov (United States)

Suarez-Bertoa, Ricardo; Astorga, Covadonga

2018-03-01

Hydrocarbons, CO, NOx, NH 3 , N 2 O, CO 2 and particulate matter emissions affect air quality, global warming and human health. Transport sector is an important source of these pollutants and high pollution episodes are often experienced during the cold season. However, EU vehicle emissions regulation at cold ambient temperature only addresses hydrocarbons and CO vehicular emissions. For that reason, we have studied the impact that cold ambient temperatures have on Euro 6 diesel and spark ignition (including: gasoline, ethanol flex-fuel and hybrid vehicles) vehicle emissions using the World-harmonized Light-duty Test Cycle (WLTC) at -7 °C and 23 °C. Results indicate that when facing the WLTC at 23 °C the tested vehicles present emissions below the values set for type approval of Euro 6 vehicles (still using NEDC), with the exception of NOx emissions from diesel vehicles that were 2.3-6 times higher than Euro 6 standards. However, emissions disproportionally increased when vehicles were tested at cold ambient temperature (-7 °C). High solid particle number (SPN) emissions (>1 × 10 11 # km -1 ) were measured from gasoline direct injection (GDI) vehicles and gasoline port fuel injection vehicles. However, only diesel and GDI SPN emissions are currently regulated. Results show the need for a new, technology independent, procedure that enables the authorities to assess pollutant emissions from vehicles at cold ambient temperatures. Harmful pollutant emissions from spark ignition and diesel vehicles are strongly and negatively affected by cold ambient temperatures. Only hydrocarbon, CO emissions are currently regulated at cold temperature. Therefore, it is of great importance to revise current EU winter vehicle emissions regulation. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Analysis and Design of International Emission Trading Markets Applying System Dynamics Techniques

Science.gov (United States)

Hu, Bo; Pickl, Stefan

2010-11-01

The design and analysis of international emission trading markets is an important actual challenge. Time-discrete models are needed to understand and optimize these procedures. We give an introduction into this scientific area and present actual modeling approaches. Furthermore, we develop a model which is embedded in a holistic problem solution. Measures for energy efficiency are characterized. The economic time-discrete "cap-and-trade" mechanism is influenced by various underlying anticipatory effects. With a systematic dynamic approach the effects can be examined. First numerical results show that fair international emissions trading can only be conducted with the use of protective export duties. Furthermore a comparatively high price which evokes emission reduction inevitably has an inhibiting effect on economic growth according to our model. As it always has been expected it is not without difficulty to find a balance between economic growth and emission reduction. It can be anticipated using our System Dynamics model simulation that substantial changes must be taken place before international emissions trading markets can contribute to global GHG emissions mitigation.

Future Time Perspective Impacts Gain-Related but Not Loss-Related Intertemporal Choice.

Science.gov (United States)

Li, Tian; Tan, Yuxin; Gong, Xianmin; Yin, Shufei; Qiu, Fangshu; Hu, Xue

2018-01-01

Future time perspective (FTP) modulates individuals' temporal orientation in selecting their motivations and goals, which widely influences their cognitions and behaviors. However, it remains unclear how FTP exactly affects intertemporal choice. To clarify the effect of FTP on intertemporal choice, 90 college students ( M age = 21.70, SD = 1.23) were randomly assigned to the limited FTP condition (16 males, 29 females) and the open-ended FTP condition (17 males, 28 females). In the limited FTP condition, participants were instructed to imagine their states of being 70 years old, whereas in the open-ended FTP condition, they were instructed to describe their current states. All participants then completed a series of intertemporal choice tasks, in which they chose from gain- and loss-related choices occurring at various time points. Results showed that the participants who received the future-imagining manipulation had more limited FTP compared with those who did not receive the manipulation, which confirmed the validity of the FTP manipulation. A 2 (FTP: limited vs. open-ended) × 2 (type of choice: gain vs. loss) repeated measures ANOVA on discount rate revealed a significant interaction between these two factors. The participants in the limited FTP condition had higher discount rates on gain-related choices but showed no difference on loss-related choices compared with the participants under the open-ended FTP condition. The results suggest that limited FTP could lower individuals' future orientation (i.e., willingness to delay an outcome) on gain-related, but not on loss-related, intertemporal decision-making.

40 CFR 600.109-08 - EPA driving cycles.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false EPA driving cycles. 600.109-08 Section... Model Year Automobiles-Test Procedures § 600.109-08 EPA driving cycles. (a) The FTP driving cycle is prescribed in § 86.115 of this chapter. (b) The highway fuel economy driving cycle is specified in this...

Otoacoustic emissions in young adults exposed to drums noise of a college band

Directory of Open Access Journals (Sweden)

Paula Botelho da Silva

Full Text Available ABSTRACT Purpose: to identify cochlear dysfunction and occurrence of tinnitus in young adults exposed to drums noise of a college band. Methods: the sample included 50 subjects: 25 musicians (study group and 25 non-musicians (control group. The procedures included anamnesis, pure tone audiometry, acoustic impedance and Transient Evoked Otoacoustic Emissions, Distortion Product Otoacoustic Emissions and Distortion Product Otoacoustic Emissions Input-Output function. Results: positive correlation between the occurrence of tinnitus and the variables exposure time and use of personal stereos was found. Overall, the study group showed significantly lower Transient Evoked Otoacoustic Emissions, when compared to the control group. In the study group, there was a tendency toward worse response in 6 kHz(f2 in Distortion Product Otoacoustic Emissions in both ears. The Distortion Product Otoacoustic Emissions Input-Output function did not differ between groups nor did its slope. Conclusion: in general, otoacoustic emissions were worse in noise-exposed young people (study group when compared to the unexposed (control group, indicating that the test may be important in early identification of cochlear changes.

Emission inventory; Inventaire des emissions

Energy Technology Data Exchange (ETDEWEB)

Fontelle, J.P. [CITEPA, Centre Interprofessionnel Technique d`Etudes de la Pollution Atmospherique, 75 - Paris (France)

1997-12-31

Statistics on air pollutant (sulfur dioxide, nitrogen oxides and ammonium) emissions, acid equivalent emissions and their evolution since 1990 in the various countries of Europe and the USA, are presented. Emission data from the industrial, agricultural, transportation and power sectors are given, and comparisons are carried out between countries based on Gnp and population, pollution import/export fluxes and compliance to the previous emission reduction objectives

Consistency checks in beam emission modeling for neutral beam injectors

International Nuclear Information System (INIS)

Punyapu, Bharathi; Vattipalle, Prahlad; Sharma, Sanjeev Kumar; Baruah, Ujjwal Kumar; Crowley, Brendan

2015-01-01

In positive neutral beam systems, the beam parameters such as ion species fractions, power fractions and beam divergence are routinely measured using Doppler shifted beam emission spectrum. The accuracy with which these parameters are estimated depend on the accuracy of the atomic modeling involved in these estimations. In this work, an effective procedure to check the consistency of the beam emission modeling in neutral beam injectors is proposed. As a first consistency check, at a constant beam voltage and current, the intensity of the beam emission spectrum is measured by varying the pressure in the neutralizer. Then, the scaling of measured intensity of un-shifted (target) and Doppler shifted intensities (projectile) of the beam emission spectrum at these pressure values are studied. If the un-shifted component scales with pressure, then the intensity of this component will be used as a second consistency check on the beam emission modeling. As a further check, the modeled beam fractions and emission cross sections of projectile and target are used to predict the intensity of the un-shifted component and then compared with the value of measured target intensity. An agreement between the predicted and measured target intensities provide the degree of discrepancy in the beam emission modeling. In order to test this methodology, a systematic analysis of Doppler shift spectroscopy data obtained on the JET neutral beam test stand data was carried out

A large sample of Kohonen-selected SDSS quasars with weak emission lines: selection effects and statistical properties

Science.gov (United States)

Meusinger, H.; Balafkan, N.

2014-08-01

Aims: A tiny fraction of the quasar population shows remarkably weak emission lines. Several hypotheses have been developed, but the weak line quasar (WLQ) phenomenon still remains puzzling. The aim of this study was to create a sizeable sample of WLQs and WLQ-like objects and to evaluate various properties of this sample. Methods: We performed a search for WLQs in the spectroscopic data from the Sloan Digital Sky Survey Data Release 7 based on Kohonen self-organising maps for nearly 105 quasar spectra. The final sample consists of 365 quasars in the redshift range z = 0.6 - 4.2 (z¯ = 1.50 ± 0.45) and includes in particular a subsample of 46 WLQs with equivalent widths WMg iiattention was paid to selection effects. Results: The WLQs have, on average, significantly higher luminosities, Eddington ratios, and accretion rates. About half of the excess comes from a selection bias, but an intrinsic excess remains probably caused primarily by higher accretion rates. The spectral energy distribution shows a bluer continuum at rest-frame wavelengths ≳1500 Å. The variability in the optical and UV is relatively low, even taking the variability-luminosity anti-correlation into account. The percentage of radio detected quasars and of core-dominant radio sources is significantly higher than for the control sample, whereas the mean radio-loudness is lower. Conclusions: The properties of our WLQ sample can be consistently understood assuming that it consists of a mix of quasars at the beginning of a stage of increased accretion activity and of beamed radio-quiet quasars. The higher luminosities and Eddington ratios in combination with a bluer spectral energy distribution can be explained by hotter continua, i.e. higher accretion rates. If quasar activity consists of subphases with different accretion rates, a change towards a higher rate is probably accompanied by an only slow development of the broad line region. The composite WLQ spectrum can be reasonably matched by the

Computational integration of the phases and procedures of calibration processes for radioprotection

International Nuclear Information System (INIS)

Santos, Gleice R. dos; Thiago, Bibiana dos S.; Rocha, Felicia D.G.; Santos, Gelson P. dos; Potiens, Maria da Penha A.; Vivolo, Vitor

2011-01-01

This work proceed the computational integration of the processes phases by using only a single computational software, from the entrance of the instrument at the Instrument Calibration Laboratory (LCI-IPEN) to the conclusion of calibration procedures. So, the initial information such as trade mark, model, manufacturer, owner, and the calibration records are digitized once until the calibration certificate emission

Presentation at FTP: A review

International Nuclear Information System (INIS)

Sheffield, J.

1987-01-01

This series of vugraphs presents some information concerning ORNL's involvement in the fusion energy research program. Recent and future experiments are named, and a rough estimate of funding is given

Compound list: chlorpheniramine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available chlorpheniramine CHL 00090 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/chlorpheni...ramine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATE...ST/Rat/in_vivo/Liver/Single/chlorpheniramine.Rat.in_vivo.Liver.Single.zip ftp://f...tp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/chlorpheniramine.Rat.in_vivo.Liver.Repeat.zip ...

Reviewer Volume 29, Tahun 2009

OpenAIRE

Volume 29, Tahun 2009, Reviewer

2012-01-01

Achmad Subagio, Fakultas Teknologi Pertanian (FTP), Universitas Jember, Jl. Kalimantan I, Kampus Tegal Boto, Jember 68121Agustin K., Wardani FTP, Universitas Brawijaya, Malang, Jl. Veteran, Malang 65145Bambang Purwantana, Jurusan Teknik Pertanian (TEP), FTP, Universitas Gadjah Mada (UGM), Jl. Flora, Bulaksumur,Yogyakarta 55281Chusnul Hidayat, Jurusan Teknologi Pangan dan Hasil Pertanian (TPHP), FTP, UGMDidik Purwadi, Jurusan Teknologi Industri Pertanian (TIP), FTP, UGMDjagal Wiseso Marseno, ...

Advanced Boost System Developing for High EGR Applications

Energy Technology Data Exchange (ETDEWEB)

Sun, Harold

2012-09-30

To support industry efforts of clean and efficient internal combustion engine development for passenger and commercial applications • This program focuses on turbocharger improvement for medium and light duty diesel applications, from complete system optimization percepective to enable commercialization of advanced diesel combustion technologies, such as HCCI/LTC. • Improve combined turbocharger efficiency up to 10% or fuel economy by 3% on FTP cycle at Tier II Bin 5 emission level.

Simultaneous fabrication of nanogap electrodes using field-emission-induced electromigration

International Nuclear Information System (INIS)

Ito, Mitsuki; Yagi, Mamiko; Morihara, Kohei; Shirakashi, Jun-ichi

2015-01-01

We present a simple technique for simultaneous control of the electrical properties of multiple Ni nanogaps. This technique is based on electromigration induced by a field emission current and is called “activation.” Simultaneous tuning of the tunnel resistance of multiple nanogaps was achieved by passing a Fowler–Nordheim (F-N) field emission current through an initial group of three Ni nanogaps connected in series. The Ni nanogaps, which had asymmetrical shapes with initial gap separations in the 80–110-nm range, were fabricated by electron-beam lithography and a lift-off process. By performing the activation procedure, the current–voltage properties of the series-connected nanogaps were varied simultaneously from “insulating” to “metallic” via “tunneling” properties by increasing the preset current of the activation procedure. We can also simultaneously control the tunnel resistances of the series-connected nanogaps, which range from a resistance of the order of 100 TΩ–100 kΩ, by increasing the preset current from 1 nA to 30 μA. This tendency is quite similar to that of individually activated nanogaps, and the tunnel resistance values of the simultaneously activated nanogaps were almost the same at each preset current. These results clearly imply that the electrical properties of the series-connected nanogaps can be controlled simultaneously via the activation procedure

Compound list: alpidem [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available alpidem ADM 00171 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_v...itro/alpidem.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/alpidem.Rat.in_vitro.Liver.zip ...

Compound list: buspirone [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available buspirone BPR 00173 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in..._vitro/buspirone.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/buspirone.Rat.in_vitro.Liver.zip ...

Compound list: clozapine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available clozapine CZP 00174 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in..._vitro/clozapine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/clozapine.Rat.in_vitro.Liver.zip ...

Compound list: venlafaxine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available venlafaxine VLF 00172 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/venlafaxine....Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vitro/venlafaxine.Rat.in_vitro.Liver.zip ...

Prediction of the net radon emission from a model open pit uranium mine

International Nuclear Information System (INIS)

Nielson, K.K.; Perkins, R.W.; Schwendiman, L.C.; Enderlin, W.I.

1979-04-01

Radon emission from a model open pit uranium mining operation has been estimated by applying radon exhalation fluxes measured in an open pit uranium mine to the various areas of the model mine. The model mine was defined by averaging uranium concentrations and production and procedural statistics for eight major open pit uranium mines in the Casper, Wyoming area. The resulting emission rates were 740 Ci/AFR during mining operations and 33 Ci/AFR/yr after abandonment of the mine

Evaluation of analytical procedures for the determination of cadmium, boron and lithium in UALx samples by inductively coupled plasma optical emission spectrometry (ICP OES)

International Nuclear Information System (INIS)

Guilhen, Sabine Neusatz; Kakazu, Mauricio H.; Cotrim, Marycel Elena Barboza; Pires, Maria Aparecida Faustino; Souza, Alexandre Luiz de

2013-01-01

Used in over 80% of the worldwide diagnostic procedures, Technetium-99m ( 99m Tc), which is obtained from the decay of molybdenum-99 ( 99 Mo), is the most important radioisotope in nuclear medicine. IPEN/CNEN-SP has been developing technologies in order to produce Mo-99 by the irradiation of low-enriched uranium (LEU < 20% of 235U) targets in its research reactor IEA-R1 (IPEN, Sao Paulo/Brazil). These targets consist of low enriched uranium dispersed in a matrix of aluminum (UAlx-Al). Several impurities may be incorporated during the target's production process, such as boron, cadmium and lithium, which have a high capture cross section that may reduce the irradiation's efficiency. This study describes a simple and rapid inductively coupled plasma optical emission spectrometric method for the determination of cadmium, boron and lithium in uranium aluminum (UAlx) dispersion targets. The method involves a previous separation step, in which uranium gets removed from the matrix by chromatographic extraction with the use of a divinylbenzene resin Amberlite XAD - 4 doped with tri-n-butyl phosphate (TBP). TBP selectively separates the uranium, leaving behind the impurities in an aqueous medium for a further quantification by ICP OES. Possible spectroscopic interferences are also discussed in this article, because of the high amount of aluminum in the remaining solution. Experimental and instrumental conditions, such as initial mass, acid solution ratio and amount, resin mass, emission lines and interfering concentrations are carefully established. This method is to be applied for the determination of several others impurities in UAlx in the future, providing means to verify the UAlx targets' compliance to the current established specifications through routine laboratory analysis. (author)

Nitrous oxide emissions from cropland: a procedure for calibrating the DayCent biogeochemical model using inverse modelling

Science.gov (United States)

Rafique, Rashad; Fienen, Michael N.; Parkin, Timothy B.; Anex, Robert P.

2013-01-01

DayCent is a biogeochemical model of intermediate complexity widely used to simulate greenhouse gases (GHG), soil organic carbon and nutrients in crop, grassland, forest and savannah ecosystems. Although this model has been applied to a wide range of ecosystems, it is still typically parameterized through a traditional “trial and error” approach and has not been calibrated using statistical inverse modelling (i.e. algorithmic parameter estimation). The aim of this study is to establish and demonstrate a procedure for calibration of DayCent to improve estimation of GHG emissions. We coupled DayCent with the parameter estimation (PEST) software for inverse modelling. The PEST software can be used for calibration through regularized inversion as well as model sensitivity and uncertainty analysis. The DayCent model was analysed and calibrated using N2O flux data collected over 2 years at the Iowa State University Agronomy and Agricultural Engineering Research Farms, Boone, IA. Crop year 2003 data were used for model calibration and 2004 data were used for validation. The optimization of DayCent model parameters using PEST significantly reduced model residuals relative to the default DayCent parameter values. Parameter estimation improved the model performance by reducing the sum of weighted squared residual difference between measured and modelled outputs by up to 67 %. For the calibration period, simulation with the default model parameter values underestimated mean daily N2O flux by 98 %. After parameter estimation, the model underestimated the mean daily fluxes by 35 %. During the validation period, the calibrated model reduced sum of weighted squared residuals by 20 % relative to the default simulation. Sensitivity analysis performed provides important insights into the model structure providing guidance for model improvement.

Comprehensive Characterization Of Ultrafine Particulate Emission From 2007 Diesel Engines: PM Size Distribution, Loading And Indidividual Particle Size And Composition.

Science.gov (United States)

Zelenyuk, A.; Cuadra-Rodriguez, L. A.; Imre, D.; Shimpi, S.; Warey, A.

2006-12-01

The strong absorption of solar radiation by black carbon (BC) impacts the atmospheric radiative balance in a complex and significant manner. One of the most important sources of BC is vehicular emissions, of which diesel represents a significant fraction. To address this issue the EPA has issues new stringent regulations that will be in effect in 2007, limiting the amount of particulate mass that can be emitted by diesel engines. The new engines are equipped with aftertreatments that reduce PM emissions to the point, where filter measurements are subject to significant artifacts and characterization by other techniques presents new challenges. We will present the results of the multidisciplinary study conducted at the Cummins Technical Center in which a suite of instruments was deployed to yield comprehensive, temporally resolved information on the diesel exhaust particle loadings and properties in real-time: Particle size distributions were measured by Engine Exhaust Particle Sizer (EEPS) and Scanning Mobility Particle Sizer (SMPS). Total particle diameter concentration was obtained using Electrical Aerosol Detector (EAD). Laser Induced Incandescence and photoacoustic techniques were used to monitor the PM soot content. Single Particle Laser Ablation Time-of- flight Mass Spectrometer (SPLAT) provided the aerodynamic diameter and chemical composition of individual diesel exhaust particles. Measurements were conducted on a number of heavy duty diesel engines operated under variety of operating conditions, including FTP transient cycles, ramped-modal cycles and steady states runs. We have also characterized PM emissions during diesel particulate filter regeneration cycles. We will present a comparison of PM characteristics observed during identical cycles, but with and without the use of aftertreatment. A total of approximately 100,000 individual particles were sized and their composition characterized by SPLAT. The aerodynamic size distributions of the characterized

Papers of the PTAC energy conservation and air emissions case studies forum

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

This forum discussed different approaches to energy consumption and GHG emissions from the upstream oil and gas sector in Canada. Overviews of new technologies for emissions reduction and eco-efficiency were presented, such as the use of catalytic converters and fire-tube immersion heaters. Approaches to energy efficiency through lubrication procedures, pneumatic instrumentation and incinerators were also presented. Issues concerning cost reduction and natural gas emissions were discussed, as well as the use of energy monitoring systems to promote profit and efficiency. The optimization of various systems was also a focal point of the forum, including new methods and approaches towards mole sieve adsorption cycle optimization. Twelve papers were presented at this forum, three of which have been catalogued separately for inclusion in this database. tabs, figs.

Exhaust gas emissions evaluation in the flight of a multirole fighter equipped with a F100-PW-229 turbine engine

Directory of Open Access Journals (Sweden)

Markowski Jarosław

2017-01-01

Full Text Available The issue of exhaust gas emission generated by turbine engines described in ICAO Annex 16 of the International Civil Aviation Convention includes a number of procedures and requirements. Their implementation is aimed at determining the value of the engine’s environmental parameters and comparing them to the values specified in the norms. The turbine engine exhaust gas emission test procedures are defined as stationary and the operating parameters values are set according to the LTO test. The engine load setting values refer to engine operating parameters that occur when the plane is in the vicinity of airports. Such a procedure is dedicated to civilian passenger and transport aircraft. The operating conditions of a multirole fighter aircraft vary considerably from passenger aircraft and the variability of their flight characteristics requires a special approach in assessing its environmental impact. This article attempts to evaluate the exhaust gas emissions generated by the turbine engine in a multirole fighter flight using the parameters recorded by the onboard flight recorder.

Compound list: acetamide [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available acetamide AAA 00169 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/acetam...ide.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/acetamide.Rat.in_vivo.Liver.Repeat.zip ...

Ion cyclotron emission by spontaneous emission

Energy Technology Data Exchange (ETDEWEB)

Da Costa, O [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Gresillon, D [Ecole Polytechnique, 91 - Palaiseau (France). Lab. de Physique des Milieux Ionises

1994-07-01

The goal of the study is to examine whether the spontaneous emission can account for ICE (ion cyclotron emission) experimental results, or part of them. A straightforward approach to plasma emission is chosen, investigating the near equilibrium wave radiation by gyrating ions, and thus building from the majority and fast fusion ions the plasma fluctuations and emission on the fast magnetoacoustic or compressional Alfven wave mode in the IC frequency range. Similarities with the ICE experiments are shown: the emission temperature in the presence of fast ions (even in a very small amount), the strong fast ion emission increase with the harmonic, the fine double-line splitting of each peak, the linear but not proportional increase of the peak width with the harmonic. 3 refs., 2 figs.

Ion cyclotron emission by spontaneous emission

International Nuclear Information System (INIS)

Da Costa, O.; Gresillon, D.

1994-01-01

The goal of the study is to examine whether the spontaneous emission can account for ICE (ion cyclotron emission) experimental results, or part of them. A straightforward approach to plasma emission is chosen, investigating the near equilibrium wave radiation by gyrating ions, and thus building from the majority and fast fusion ions the plasma fluctuations and emission on the fast magnetoacoustic or compressional Alfven wave mode in the IC frequency range. Similarities with the ICE experiments are shown: the emission temperature in the presence of fast ions (even in a very small amount), the strong fast ion emission increase with the harmonic, the fine double-line splitting of each peak, the linear but not proportional increase of the peak width with the harmonic. 3 refs., 2 figs

Examining carbon emissions economic growth nexus for India: A multivariate cointegration approach

International Nuclear Information System (INIS)

Ghosh, Sajal

2010-01-01

The study probes cointegration and causality between carbon emissions and economic growth for India using ARDL bounds testing approach complemented by Johansen-Juselius maximum likelihood procedure in a multivariate framework by incorporating energy supply, investment and employment for time span 1971-2006. The study fails to establish long-run equilibrium relationship and long term causality between carbon emissions and economic growth; however, there exists a bi-directional short-run causality between the two. Hence, in the short-run, any effort to reduce carbon emissions could lead to a fall in the national income. This study also establishes unidirectional short-run causality running from economic growth to energy supply and energy supply to carbon emissions. The absence of causality running from energy supply to economic growth implies that in India, energy conservation and energy efficiency measures can be implemented to minimize the wastage of energy across value chain. Such measures would narrow energy demand-supply gap. Absence of long-run causality between carbon emissions and economic growth implies that in the long-run, focus should be given on harnessing energy from clean sources to curb carbon emissions, which would not affect the country's economic growth.

Effluent monitoring Quality Assurance Project Plan for radioactive airborne emissions data. Revision 2

International Nuclear Information System (INIS)

Frazier, T.P.

1995-12-01

This Quality Assurance Project Plan addresses the quality assurance requirements for compiling Hanford Site radioactive airborne emissions data. These data will be reported to the U.S. Environmental Protection Agency, the US Department of Energy, and the Washington State Department of Health. Effluent Monitoring performs compliance assessments on radioactive airborne sampling and monitoring systems. This Quality Assurance Project Plan is prepared in compliance with interim guidelines and specifications. Topics include: project description; project organization and management; quality assurance objectives; sampling procedures; sample custody; calibration procedures; analytical procedures; monitoring and reporting criteria; data reduction, verification, and reporting; internal quality control; performance and system audits; corrective actions; and quality assurance reports

Final Rule for Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures

Science.gov (United States)

EPA adopted emission standards and related provisions for aircraft gas turbine engines with rated thrusts greater than 26.7 kilonewtons. These engines are used primarily on commercial passenger and freight aircraft.

Compound list: 2-nitrofluorene [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available 2-nitrofluorene 2NF 00160 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Human/in_vitro/2-nitroflu...orene.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Single/2-nitrofluorene.Rat.in_vivo.Liver.Single.zip ...

Compound list: N-nitrosomorpholine [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available N-nitrosomorpholine NMOR 00163 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATE...es/LATEST/Rat/in_vivo/Liver/Single/N-nitrosomorpholine.Rat.in_vivo.Liver.Single.zip ... ...ST/Human/in_vitro/N-nitrosomorpholine.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-tggat

Reviewer Volume 27, Tahun 2007

OpenAIRE

Volume 27, Tahun 2007, Reviewer

2007-01-01

1. Abdul Rozaq, Dr., Ir., DAA Jurusan Teknik Pertanian (TEP), Fakultas Teknologi Pertanian (FTP), Universitas Gadjah Mada (UGM), Yogyakarta2. Bambang Purwantana, Ir., Dr., M.Agr. Jurusan TEP, FTP-UGM3. Chusnul Hidayat, Ir., Dr. Jurusan Teknologi Pangan dan Hasil Pertanian (TPHP), Fakultas Teknologi Pertanian (FTP), Universitas Gadjah Mada (UGM), Yogyakarta4. Haryadi, Ir., Dr., Prof., M. App. Sc. Jurusan TPHP, FTP-UGM5. Lilik Sutiarso, Ir., Dr., M. Eng. Jurusan TEP, FTP-UGM6. Pudji Hastuti, Ir...

Emission ratio and isotopic signatures of molecular hydrogen emissions from tropical biomass burning

Science.gov (United States)

Haumann, F. A.; Batenburg, A. M.; Pieterse, G.; Gerbig, C.; Krol, M. C.; Röckmann, T.

2013-09-01

In this study, we identify a biomass-burning signal in molecular hydrogen (H2) over the Amazonian tropical rainforest. To quantify this signal, we measure the mixing ratios of H2 and several other species as well as the H2 isotopic composition in air samples that were collected in the BARCA (Balanço Atmosférico Regional de Carbono na Amazônia) aircraft campaign during the dry season. We derive a relative H2 emission ratio with respect to carbon monoxide (CO) of 0.31 ± 0.04 ppb ppb-1 and an isotopic source signature of -280 ± 41‰ in the air masses influenced by tropical biomass burning. In order to retrieve a clear source signal that is not influenced by the soil uptake of H2, we exclude samples from the atmospheric boundary layer. This procedure is supported by data from a global chemistry transport model. The ΔH2 / ΔCO emission ratio is significantly lower than some earlier estimates for the tropical rainforest. In addition, our results confirm the lower values of the previously conflicting estimates of the H2 isotopic source signature from biomass burning. These values for the emission ratio and isotopic source signatures of H2 from tropical biomass burning can be used in future bottom-up and top-down approaches aiming to constrain the strength of the biomass-burning source for H2. Hitherto, these two quantities relied only on combustion experiments or on statistical relations, since no direct signal had been obtained from in-situ observations.

Small-Chamber Measurements of Chemical-Specific Emission Factors for Drywall

Energy Technology Data Exchange (ETDEWEB)

Maddalena, Randy; Russell, Marion; Apte, Michael G.

2010-06-01

Imported drywall installed in U.S. homes is suspected of being a source of odorous and potentially corrosive indoor pollutants. To support an investigation of those building materials by the Consumer Products Safety Commission (CPSC), Lawrence Berkeley National Laboratory (LBNL) measured chemical-specific emission factors for 30 samples of drywall materials. Emission factors are reported for 75 chemicals and 30 different drywall samples encompassing both domestic and imported stock and incorporating natural, synthetic, or mixed gypsum core material. CPSC supplied all drywall materials. First the drywall samples were isolated and conditioned in dedicated chambers, then they were transferred to small chambers where emission testing was performed. Four sampling and analysis methods were utilized to assess (1) volatile organic compounds, (2) low molecular weight carbonyls, (3) volatile sulfur compounds, and (4) reactive sulfur gases. LBNL developed a new method that combines the use of solid phase microextraction (SPME) with small emission chambers to measure the reactive sulfur gases, then extended that technique to measure the full suite of volatile sulfur compounds. The testing procedure and analysis methods are described in detail herein. Emission factors were measured under a single set of controlled environmental conditions. The results are compared graphically for each method and in detailed tables for use in estimating indoor exposure concentrations.

Applying 'Evidence-Based Medicine' Theory to Interventional Radiology.Part 2: A Spreadsheet for Swift Assessment of Procedural Benefit and Harm

International Nuclear Information System (INIS)

MacEneaney, Peter M.; Malone, Dermot E.

2000-01-01

AIM: To design a spreadsheet program to analyse interventional radiology (IR) data rapidly produced in local research or reported in the literature using 'evidence-based medicine' (EBM) parameters of treatment benefit and harm. MATERIALS AND METHODS: Microsoft Excel TM was used. The spreadsheet consists of three worksheets. The first shows the 'Levels of Evidence and Grades of Recommendations' that can be assigned to therapeutic studies as defined by the Oxford Centre for EBM. The second and third worksheets facilitate the EBM assessment of therapeutic benefit and harm. Validity criteria are described. These include the assessment of the adequacy of sample size in the detection of possible procedural complications. A contingency (2 x 2) table for raw data on comparative outcomes in treated patients and controls has been incorporated. Formulae for EBM calculations are related to these numerators and denominators in the spreadsheet. The parameters calculated are benefit -- relative risk reduction, absolute risk reduction, number needed to treat (NNT). Harm -- relative risk, relative odds, number needed to harm (NNH). Ninety-five per cent confidence intervals are calculated for all these indices. The results change automatically when the data in the therapeutic outcome cells are changed. A final section allows the user to correct the NNT or NNH in their application to individual patients. RESULTS: This spreadsheet can be used on desktop and palmtop computers. The MS Excel TM version can be downloaded via the Internet from the URL ftp://radiography.com/pub/TxHarm00.xls. CONCLUSION: A spreadsheet is useful for the rapid analysis of the clinical benefit and harm from IR procedures. MacEneaney, P.M. and Malone, D.E

X-ray emission spectroscopic determination of iron in a polyurethane encapsulant curing agent

International Nuclear Information System (INIS)

Carter, J.M.; Kling, E.N.

1979-01-01

Presented is a procedure for determining the iron content in a polyurethane encapsulant curing agent by x-ray emission spectroscopy. Standards were prepared by adding ferric acetyl acetonate to a curing agent of identical composition to that being analyzed, but containing no iron. Results show that x-ray emission spectroscopy is feasible for determination of iron in the 30 to 50 ppM range. This range could probably be extended by the preparation of additional standards. Precision of the method is approximately 1.2 ppM at the 99 percent confidence level

18F-fluorodeoxyglucose positron emission tomography in colorectal cancer: value in primary staging and follow-up

International Nuclear Information System (INIS)

Joerg, L.; Heinisch, M.; Rechberger, E.; Kurz, F.; Klug, R.; Aufschnaiter, M; Hammer, J.; Langsteger, W.

2002-01-01

Positron emission tomography using 18 F-fluorodeoxyglucose (FDG-PET) is a encouraging imaging techniques allowing a highly sensitive whole-body search for malignant foci detected by their increased glucose metabolism compared with benign tissues. Several studies are now available that indicate its added value for diagnosis and staging of colorectal cancer. In all, patient management seems to be changed in 20-30 % of patients who undergo fluorodeoxyglucose positron emission tomography in addition to standard staging procedures. Fluorodeoxyglucose positron emission tomography is also useful in monitoring radiation therapy and chemotherapy. Regarding preoperative staging of primary colorectal cancer the literature is very limited. (author)

Compound list: N-methyl-N-nitrosourea [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available N-methyl-N-nitrosourea MNU 00164 ftp://ftp.biosciencedbc.jp/archive/open-tggates/LA...TEST/Human/in_vitro/N-methyl-N-nitrosourea.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/open-...tggates/LATEST/Rat/in_vivo/Liver/Single/N-methyl-N-nitrosourea.Rat.in_vivo.Liver.Single.zip ...

47 CFR 78.103 - Emissions and emission limitations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Emissions and emission limitations. 78.103... CABLE TELEVISION RELAY SERVICE Technical Regulations § 78.103 Emissions and emission limitations. (a) A CARS station may be authorized to employ any type of emission, for which there are technical standards...

Development and deployment of AQUIS: A PC-based emission inventory calculator and air information management system

Energy Technology Data Exchange (ETDEWEB)

Smith, A.E.; Tschanz, J.; Monarch, M.; Narducci, P.; Bormet, S.

1995-06-01

The Air Quality Utility Information System (AQUIS) is a database management system. AQUIS assists users in calculation emissions, both traditional and toxic, and tracking and reporting emissions and source information. With some facilities having over 1200 sources and AQUIS calculating as many as 125 pollutants for a single source, tracking and correlating this information involve considerable effort. Originally designed for use at seven facilities of the Air Force Material Command, the user community has expanded to over 50 facilities since last reported at the 1993 Air and Waste Management Association (AWMA) annual meeting. This expansion in the user community has provided an opportunity to test the system under expanded operating conditions and in applications not anticipated during original system design. User feedback is used to determine needed enhancements and features and to prioritize the content of new releases. In responding to evolving user needs and new emission calculation procedures, it has been necessary to reconfigure AQUIS several times. Reconfigurations have ranged from simple to complex. These changes have necessitated augmenting quality assurance (QA) and validation procedures.

Infrared Emission Spectrum of the Hydroxyl Radical: A Novel Experiment in Molecular Spectroscopy.

Science.gov (United States)

Henderson, Giles; And Others

1982-01-01

Describes an experiment in which parameters from an "ab-initio" potential are used to calculate vibrational-rotational energy levels and construct a "stick spectrum" for the overtone emission of the hydroxyl radical. Provides background information on ab-initio spectrum, experimental procedures, and analysis of data. (Author/JN)

Low-background measurements of neutron emission from Ti metal in pressurized deuterium gas

International Nuclear Information System (INIS)

Menlove, H.O.; Paciotti, M.A.; Claytor, T.N.; Tuggle, D.G.

1991-01-01

A wide variety of neutron detector systems have been used at various research facilities to search for anomalous neutron emission from deuterated metals. Some of these detector systems are summarized here together with possible sources of spurious signals from electronic noise. During the past two years, we have performed experiments to measure neutron emission from pressurized D 2 gas mixed with various forms of titanium metal chips and sponge. Details concerning the neutron detectors, experimental procedures, and results have been reported previously. Our recent experiments have focused on increasing the low-level neutron emission and finding a way to trigger the emission. To improve our detection sensitivity, we have increased the shielding in our counting laboratory, changed to low-background 3 He tubes, and set up additional detector systems in deep underground counting stations. This report is an update on this experimental work. 7 refs., 5 figs., 4 tabs

Acoustic emission

International Nuclear Information System (INIS)

Nichols, R.W.

1976-01-01

The volume contains six papers which together provide an overall review of the inspection technique known as acoustic emission or stress wave emission. The titles are: a welder's introduction to acoustic emission technology; use of acoustic emission for detection of defects as they arise during fabrication; examples of laboratory application and assessment of acoustic emission in the United Kingdom; (Part I: acoustic emission behaviour of low alloy steels; Part II: fatigue crack assessment from proof testing and continuous monitoring); inspection of selected areas of engineering structures by acoustic emission; Japanese experience in laboratory and practical applications of acoustic emission to welded structures; and ASME acoustic emission code status. (U.K.)

Determination of inorganic beryllium species in the particulate matter of emissions and working areas

Energy Technology Data Exchange (ETDEWEB)

Profumo, A.; Spini, G.; Cucca, L.; Pesavento, M. [Dipartimento di Chimica Gen., Pavia (Italy)

2002-07-01

A sequential extraction procedure for separating and determining Be(0), soluble Be(II) inorganic compounds, BeO and beryllium silicates in samples, such as particulate matter of emissions and working areas, has been developed. The proposed procedure has been tested on synthetic samples prepared with the inorganic beryllium compounds, in the presence of atmospherical particulate matter sampled in a laboratory, previously checked for the absence of beryllium. The speciation was then repeated on a sample of fly ash deriving from a solid waste incinerator and on a reference material (Coal Fly ash SRM 1633a, by NIST), followed by an evaluation of matrix spiking and recovery analyses. Performing multiple analyses of the spiked samples assessed the repeatability of the procedure. Quantitative determinations have been made by inductively coupled plasma optical emission spectrometry (ICP-OES) and electrothermal atomic absorption spectrometry (ETAAS). The possible interferences of the most common ions have been investigated. The selective sequential extractions allow one to separate and to determine different inorganic beryllium species, to which a different toxicity and therefore, a different risk are related: it is the case for example of metallic beryllium and beryllium oxide.

Monitoring greenhouse gas emissions from landfill sites

International Nuclear Information System (INIS)

Eade, G.

2001-01-01

Methane is the chief component of natural gas, but also occurs naturally by the anaerobic decomposition of organic matter in swamp areas, at landfill sites, in fact at any location where organic deposits are present. Carbon dioxide is also produced by the decomposition of organic material as well as being the primary by-product of combustion. This article focuses on techniques to test a wide variety of combustible and toxic gases, including surface emission testing of landfill sites. Specifically, it describes the Methane Emission Monitoring System (MEMS) developed by Hetek Solutions Inc., whose primary objective is to to effectively locate surface emissions of methane gas from active landfill sites using flame ionization (FI) technology, and to plot the 'hot spots' using a Differential Global Positioning System (DGPS), which provides sub-metre accuracy for plotting emissions locations at landfill sites. The FI equipment is installed on all-terrain vehicles (ATVs). Several thousand kilometers of pipeline inspections have been performed in Alberta and Saskatchewan using this system in the mid-1990s. The mobile FI/ATV units have been redesigned for landfill gas emission testing, equipped with new DGPS equipment and interface software. They meet the New Source Performance Standards (NSPS) drafted in the United States in 1996, which requires all landfill sites to be inspected for methane gas emissions. Using the FI/ATV combination, productivity over conventional walking inspection procedures increased some 400 per cent, while monitoring accuracy is equivalent to or better than those provided by previous conventional methods. The company can also provide the Optical Methane Detector (OMD) system using infrared technology. They are capable of performing 14,000 measurements per second, thus providing immediate response. To date, ATV emissions testing has been proven to be very effective in various types of gas detection. When interfaced with DGPS technology, computer

Measurement of electron emission due to energetic ion bombardment in plasma source ion implantation

Science.gov (United States)

Shamim, M. M.; Scheuer, J. T.; Fetherston, R. P.; Conrad, J. R.

1991-11-01

An experimental procedure has been developed to measure electron emission due to energetic ion bombardment during plasma source ion implantation. Spherical targets of copper, stainless steel, graphite, titanium alloy, and aluminum alloy were biased negatively to 20, 30, and 40 kV in argon and nitrogen plasmas. A Langmuir probe was used to detect the propagating sheath edge and a Rogowski transformer was used to measure the current to the target. The measurements of electron emission coefficients compare well with those measured under similar conditions.

Testing of acoustic emission method during pressure tests of WWER-440 steam generators and pressurizers

International Nuclear Information System (INIS)

Wuerfl, K.; Crha, J.

1987-01-01

The results are discussed of measuring acoustic emission in output pressure testing of steam generators and pressurizers for WWER-440 reactors. The objective of the measurements was to test the reproducibility of measurements and to find the criterion which would be used in assessing the condition of the components during manufacture and in operation. The acoustic emission was measured using a single-channel Dunegan/Endevco apparatus and a 16-channel LOCAMAT system. The results showed that after the first assembly, during a repeat dismantle of the lids and during seal replacement, processes due to seal contacts and bolt and washer deformations were the main source of acoustic emission. A procedure was defined of how to exclude new acoustic emission sources in such cases. The acoustic emission method can be used for the diagnostics of plastic deformation processes or of crack production and propagation in components during service. (Z.M.)

Mobil emission reduction credits for natural gas vehicle programs

International Nuclear Information System (INIS)

Baker, G.F.

1993-01-01

Since the passage of the Clean Air Act Amendments in 1990, there has been increasing interest among regulators and business interests alike in innovative, market-based strategies to air quality control. In particular, larger metropolitan areas have begun to examine marketable emission reduction credit (ERC) programs. These programs limit the total allowable emissions in a non-attainment area, allocate these emission open-quotes creditsclose quotes among sources in the region, and allow the sources to redistribute their allowances through trading. This approach provides for the most cost-effective distribution of control burdens among affected sources, taking advantage of the differences in marginal control costs. Some control measures applied to mobile sources may be significantly less expensive than those applied to stationary sources, making mobile sources an excellent candidate for inclusion in an ERC program. However, there are several potential problems involving quantification, enforcement, and credit trading issues that hinder the development of mobile source ERC programs. This paper will evaluate those obstacles and discuss how they are being addressed in a Natural Gas Vehicle (NGV) program currently under development for the Houston ozone non-attainment area. Specifically, the study will outline the credit validation (i.e., quantification) procedure, including baseline emission determination and emission testing for each NGV in the program. In addition, the study will describe the vehicle/fuel consumption tracking system, and discuss issues related to credit trading with stationary sources. Finally, observations are made concerning the applicability of mobile ERC programs for other emission control measures such as old vehicle scrappage and vehicle Inspection and Maintenance programs

Proactive Student Engagement with Fitness to Practise

Directory of Open Access Journals (Sweden)

Kristin Lo

2014-01-01

Full Text Available Fitness to practise (FTP is fundamental to health professional education and health service delivery, impacting on both practitioner and client wellbeing. Literature exploring FTP support policies primarily identifies retrospective student support and management. This study describes student perceptions of an innovative FTP policy which supports students and staff to proactively identify FTP management strategies prior to entering the clinical environment. Forty-nine final year physiotherapy students were surveyed regarding their perceptions of self-declaring FTP. Ordinal data from Likert scales were reported using descriptive statistics. Thematic analysis was undertaken for open text responses. The response rate was 88%. Forty-two percent of students stated that they had experienced FTP concerns during the course. Concerns included physical and mental impairment and clinical competence issues. The majority of students (80% indicated that they were “comfortable” or “very comfortable” in self-declaring FTP issues. Confidentiality, positive relationships with staff and a supportive environment enhanced likelihood of declaration. Eight students (19% met with university staff to develop management strategies and all rated these meetings as “helpful” or “very helpful.” Students had positive perceptions of self-declaring their FTP to enable early development of management strategies. This strategy successfully navigates sensitive ethicolegal issues, empowering students to take responsibility for their own FTP.

Future Time Perspective in the Work Context: A Systematic Review of Quantitative Studies

Science.gov (United States)

Henry, Hélène; Zacher, Hannes; Desmette, Donatienne

2017-01-01

A core construct in the lifespan theory of socioemotional selectivity, future time perspective (FTP) refers to individuals’ perceptions of their remaining time in life. Its adaptation to the work context, occupational future time perspective (OFTP), entails workers’ perceptions of remaining time and opportunities in their careers. Over the past decade, several quantitative studies have investigated antecedents and consequences of general FTP and OFTP in the work context (i.e., FTP at work). We systematically review and critically discuss this literature on general FTP (k = 17 studies) and OFTP (k = 16 studies) and highlight implications for future research and practice. Results of our systematic review show that, in addition to its strong negative relationship with age, FTP at work is also associated with other individual (e.g., personality traits) and contextual variables (e.g., job characteristics). Moreover, FTP at work has been shown to mediate and moderate relationships of individual and contextual antecedents with occupational well-being, as well as motivational and behavioral outcomes. As a whole, findings suggest that FTP at work is an important variable in the field of work and aging, and that future research should improve the ways in which FTP at work is measured and results on FTP at work are reported. PMID:28400741

Future Time Perspective in the Work Context: A Systematic Review of Quantitative Studies.

Science.gov (United States)

Henry, Hélène; Zacher, Hannes; Desmette, Donatienne

2017-01-01

A core construct in the lifespan theory of socioemotional selectivity, future time perspective (FTP) refers to individuals' perceptions of their remaining time in life. Its adaptation to the work context, occupational future time perspective (OFTP), entails workers' perceptions of remaining time and opportunities in their careers. Over the past decade, several quantitative studies have investigated antecedents and consequences of general FTP and OFTP in the work context (i.e., FTP at work). We systematically review and critically discuss this literature on general FTP ( k = 17 studies) and OFTP ( k = 16 studies) and highlight implications for future research and practice. Results of our systematic review show that, in addition to its strong negative relationship with age, FTP at work is also associated with other individual (e.g., personality traits) and contextual variables (e.g., job characteristics). Moreover, FTP at work has been shown to mediate and moderate relationships of individual and contextual antecedents with occupational well-being, as well as motivational and behavioral outcomes. As a whole, findings suggest that FTP at work is an important variable in the field of work and aging, and that future research should improve the ways in which FTP at work is measured and results on FTP at work are reported.

An Experimental Evaluation of Competing Age-Predictions of Future Time Perspective between Workplace and Retirement Domains.

Science.gov (United States)

Kerry, Matthew J; Embretson, Susan E

2017-01-01

Future time perspective (FTP) is defined as "perceptions of the future as being limited or open-ended" (Lang and Carstensen, 2002; p. 125). The construct figures prominently in both workplace and retirement domains, but the age-predictions are competing: Workplace research predicts decreasing FTP age-change, in contrast, retirement scholars predict increasing FTP age-change. For the first time, these competing predictions are pitted in an experimental manipulation of subjective life expectancy (SLE). A sample of N = 207 older adults (age 45-60) working full-time (>30-h/week) were randomly assigned to SLE questions framed as either 'Live-to' or 'Die-by' to evaluate competing predictions for FTP. Results indicate general support for decreasing age-change in FTP, indicated by independent-sample t -tests showing lower FTP in the 'Die-by' framing condition. Further general-linear model analyses were conducted to test for interaction effects of retirement planning with experimental framings on FTP and intended retirement; While retirement planning buffered FTP's decrease, simple-effects also revealed that retirement planning increased intentions for sooner retirement, but lack of planning increased intentions for later retirement. Discussion centers on practical implications of our findings and consequences validity evidence in future empirical research of FTP in both workplace and retirement domains.

Carbon emission reduction targeting through process integration and fuel switching with mathematical modeling

International Nuclear Information System (INIS)

Tiew, B.J.; Shuhaimi, M.; Hashim, H.

2012-01-01

Highlights: ► CO 2 emissions reduction targeting for existing plant were categorized into three groups. ► Model for CO 2 emissions reduction targeting via combination approach was developed. ► Effect of combination approach onto HEN area efficiency was discussed. ► Proposed execution strategy can avoid HEN area efficiency deterioration. -- Abstract: Carbon emission reduction targeting is an important and effective effort for industry to contribute in controlling greenhouse gases concentration in atmosphere. Graphical approach has been proposed for CO 2 emissions reduction targeting via HEN retrofit and fuel switching. However, it involves potentially time consuming manual procedures and the quality of solutions produced greatly depends on designer’s experience and judgment. Besides, graphical approach hardly account for the cost factor during the design phase, thus potentially generate complex design. This paper introduces an MINLP model for simultaneous CO 2 emissions reduction targeting via fuel switching and HEN retrofit. A sequential model execution was proposed along with the proposed model. The application of the model on a crude preheat train case study has demonstrated its workability to generate optimal solution for targeted CO 2 emissions reduction at minimum payback period.

Hydrogen Fuel Cell Vehicle Fuel Economy Testing at the U.S. EPA National Vehicle and Fuel Emissions Laboratory (SAE Paper 2004-01-2900)

Science.gov (United States)

The introduction of hydrogen fuel cell vehicles and their new technology has created the need for development of new fuel economy test procedures and safety procedures during testing. The United States Environmental Protection Agency-National Vehicle Fuels and Emissions Laborato...

A MultiAir®/MultiFuel Approach to Enhancing Engine System Efficiency

Energy Technology Data Exchange (ETDEWEB)

Reese, Ronald [Chrysler Group LLC., Auburn Hills, MI (United States)

2015-05-20

FCA US LLC (formally known as Chrysler Group LLC, and hereinafter “Chrysler”) was awarded an American Recovery and Reinvestment Act (ARRA) funded project by the Department of Energy (DOE) titled “A MultiAir®/MultiFuel Approach to Enhancing Engine System Efficiency” (hereinafter “project”). This award was issued after Chrysler submitted a proposal for Funding Opportunity Announcement DE-FOA- 0000079, “Systems Level Technology Development, Integration, and Demonstration for Efficient Class 8 Trucks (SuperTruck) and Advanced Technology Powertrains for Light-Duty Vehicles (ATP-LD).” Chrysler started work on this project on June 01, 2010 and completed testing activities on August 30, 2014. Overall objectives of this project were; Demonstrate a 25% improvement in combined Federal Test Procedure (FTP) City and Highway fuel economy over a 2009 Chrysler minivan; Accelerate the development of highly efficient engine and powertrain systems for light-duty vehicles, while meeting future emissions standards; and Create and retain jobs in accordance with the American Recovery and Reinvestment Act of 2009

An off-line two-dimensional analytical procedure for determination of polcyclic aromatic hydrocarbons in smoke aerosol

NARCIS (Netherlands)

Claessens, H.A.; Lammerts van Bueren, L.G.D.

1987-01-01

Smoke aerosol from stoves consists of a wide variety of chemical substances of which a number have toxic properties. To study the impact of aerosol emissions on health and environment reliable analytical procedures must be available for these samples. An off-line two-dimensional HPLC method is

Acoustic emission testing of piston check valves

International Nuclear Information System (INIS)

Stewart, D.L.

1994-01-01

Based on test experience at Comanche Peak Unit 1, an acoustic emission data evaluation matrix for piston check valves has been developed. The degradations represented in this matrix were selected based on Edwards piston check valve failure data reported in the Nuclear Plant Reliability Data System. Evidence to support this matrix was collected from site test data on a variety of valve types. Although still under refinement, the matrix provides three major attributes for closure verification, which have proven useful in developing test procedures for inservice testing and preventing unnecessary disassembly

Intelligent Bioreactor Management Information System (IBM-IS) for Mitigation of Greenhouse Gas Emissions

Energy Technology Data Exchange (ETDEWEB)

Paul Imhoff; Ramin Yazdani; Don Augenstein; Harold Bentley; Pei Chiu

2010-04-30

Methane is an important contributor to global warming with a total climate forcing estimated to be close to 20% that of carbon dioxide (CO2) over the past two decades. The largest anthropogenic source of methane in the US is 'conventional' landfills, which account for over 30% of anthropogenic emissions. While controlling greenhouse gas emissions must necessarily focus on large CO2 sources, attention to reducing CH4 emissions from landfills can result in significant reductions in greenhouse gas emissions at low cost. For example, the use of 'controlled' or bioreactor landfilling has been estimated to reduce annual US greenhouse emissions by about 15-30 million tons of CO2 carbon (equivalent) at costs between $3-13/ton carbon. In this project we developed or advanced new management approaches, landfill designs, and landfill operating procedures for bioreactor landfills. These advances are needed to address lingering concerns about bioreactor landfills (e.g., efficient collection of increased CH4 generation) in the waste management industry, concerns that hamper bioreactor implementation and the consequent reductions in CH4 emissions. Collectively, the advances described in this report should result in better control of bioreactor landfills and reductions in CH4 emissions. Several advances are important components of an Intelligent Bioreactor Management Information System (IBM-IS).

[Study on mercury re-emissions during fly ash utilization].

Science.gov (United States)

Meng, Yang; Wang, Shu-Xiao

2012-09-01

The amount of fly ash produced during coal combustion is around 400 million tons per year in China. About 65%-68% of fly ash is used in building material production, road construction, architecture and agriculture. Some of these utilization processes include high temperature procedures, which may lead to mercury re-emissions. In this study, experiments were designed to simulate the key process in cement production and steam-cured brick production. A temperature programmed desorption (TPD) method was used to study the mercury transformation in the major utilization processes. Mercury re-emission during the fly ash utilization in China was estimated based on the experimental results. It was found that mercury existed as HgCl2 (Hg2 Cl2), HgS and HgO in the fly ash. During the cement production process, more than 98% of the mercury in fly ash was re-emitted. In the steam-curing brick manufacturing process, the average mercury re-emission percentage was about 28%, which was dominated by the percentage of HgCl2 (Hg2 Cl2). It is estimated that the mercury re-emission during the fly ash utilization have increased from 4.07 t in 2002 to 9.18 t in 2008, of which cement industry contributes about 96.6%.

Activity-based costing evaluation of a [F-18]-fludeoxyglucose positron emission tomography study

NARCIS (Netherlands)

Krug, Bruno; Van Zanten, Annie; Pirson, Anne-Sophie; Crott, Ralph; Vander Borght, Thierry

2009-01-01

Objective: The aim of the study is to use the activity-based costing approach to give a better insight in the actual cost structure of a positron emission tomography procedure (FDG-PET) by defining the constituting components and by simulating the impact of possible resource or practice changes.

Plasma Emission Profile Recreation using Soft X-Ray Tomography

Science.gov (United States)

Page, J. W.; Mauel, M. E.; Levesque, J. P.

2015-11-01

With sufficient views from multiple diode arrays, soft X-ray tomography is an invaluable plasma diagnostic because it is a non-perturbing method to reconstruct the emission within the interior of the plasma. In preparation for the installation of new SXR arrays in HBT-EP, we compute high-resolution tomographic reconstructions of discharges having kink-like structures that rotate nearly rigidly. By assuming a uniform angular mapping from the kink mode rotation, Δϕ ~ ωΔ t, a temporal sequence from a single 16-diode fan array represents as many as 16 x 100 independent views. We follow the procedure described by Wang and Granetz and use Bessel basis functions to take the inverse Radon transform. This transform is fit to our data using a least-squares method to estimate the internal SXR emissivity as a sum of polar functions. By varying different parameters of the transformation, we optimize the quality of our recreation of the emission profile and quantify how the reconstruction changes with the azimuthal order of the transform. Supported by U.S. DOE Grant DE-FG02-86ER53222.

Monitoring of emissions and immissions from nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Schroeder, H J [Rheinisch-Westfaelisches Elektrizitaetswerk A.G., Biblis (Germany, F.R.). Betriebsverwaltung

1977-02-01

The measurement of the emission and immission of radionuclides from nuclear power stations has already been established with the inception of the peaceful uses of atomic energy. Since then it has been a firm feature of the monitoring of effects of nuclear power plants on the environment. The considerations and procedures on which the measurement programs are based are described. The ecological behaviour of radionuclides is illustrated with the aid of examples.

Diagnostic value of sectional images obtained by emission tomography

International Nuclear Information System (INIS)

Roucayrol, J.C.

1981-01-01

It is now possible to obtain clear images of the various planes in and around a structure with ultra-sounds (echotomography), X-rays (computerized tomography) and recently, gamma-rays from radioactive substances (emission tomography). Axial transverse tomography, which is described here, is to conventional scintigraphy what CT scan is to radiography. It provides images of any structure capable of concentrating sufficiently a radioactive substance administered intravenously. These images are perpendicular to the longitudinal axis of the body. As shown by examples in the liver, lungs and myocardium, lesions which had passed unnoticed with other exploratory techniques can now be demonstrated, and the location, shape and extension of known lesions can be more accurately assessed. Emission tomography already has its place in modern diagnostic procedures side by side with echotomography and CT scan [fr

Influence of the Emissions Trading Scheme on generation scheduling

International Nuclear Information System (INIS)

Kockar, Ivana; McDonald, James R.; Conejo, Antonio J.

2009-01-01

The paper investigates the effects of emissions constraints and Emissions Trading Scheme (ETS) on the generation scheduling outcome. ETS is a cap-and-trade market mechanism that has been introduced in European Union in order to facilitate CO 2 emissions management. This scheme gives generators certain amount of CO 2 allowances which they can use to cover emissions produced during energy generation. In a current setting, most of the allowances are given for free. However, under ETS generators also have an opportunity to buy and sell CO 2 allowances on the market. Since generation power outputs are bounded by the amount of CO 2 emissions that they are allowed to produce over time, it is becoming increasingly important for generating units to manage their allocations in the most profitable way and decide when and how much of permissions to spent to produce electricity. The method proposed here allows for modeling of this new limitation by including costs of buying and selling of CO 2 allowance in the generation scheduling procedure. It also introduces additional emissions constraints in the problem formulation. Although CO 2 permissions and energy are traded in separate markets, the proposed formulation permits analysis on how emission caps and emission market prices can influence market outcome. The method is illustrated on a 5-unit system. Given examples compare (i) a base-case when all generators have made a decision to use portions of their total free allocations that do not cause any shortfall during the investigated time period; (ii) two cases when the least expensive generators' decisions on the amount of free allowances they are willing to use during the considered period are insufficient. In all cases generators also submit prices at which they expect to be able to ''top-up'' or sell allowances on the market, however, only in the second and third case the ''buying'' option becomes active and affects generation scheduling and total costs. In addition, the

(reprocessed)HeliscopeCAGE sequencing, Delve mapping and CAGE TSS aggregation - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...ntified by CAGE tag analysis (BED format) *.rdna.fa.gz: rDNA sequences (FASTA format) Data file File name: fantom...5_rp_exp_details.zip File URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/20161221/fantom5_rp_exp_detai...tp://ftp.biosciencedbc.jp/archive/fantom5/datafiles/reprocessed/hg38_latest/basic/ File size: 1.4 TB File na...me: (reprocessed)basic (Mus musculus) File URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/datafiles/reproce

Sensitive emission spectrometric method for the analysis of airborne particulate matter

International Nuclear Information System (INIS)

Sugimae, A.

1975-01-01

A rapid and sensitive emission spectrometric method for the routine analysis of airborne particulate matter collected on the glass fiber filter is reported. The method is a powder--dc arc technique involving no chemical pre-enrichment procedures. The elements--Ag, BA: Be, Bi, Cd, Co, Cr, Cu, Fe, Ga, La, Mn, Ni, Pb, Sn, V, Y, Yb, and Zn--were determined. (U.S.)

Emission Facilities - Air Emission Plants

Data.gov (United States)

NSGIC Education | GIS Inventory — Represents the Primary Facility type Air Emission Plant (AEP) point features. Air Emissions Plant is a DEP primary facility type related to the Air Quality Program....

First approach to exhaust emissions characterization of light vehicles in Montevideo, Uruguay.

Science.gov (United States)

D'Angelo, Mauro; González, Alice Elizabeth; Rezzano Tizze, Nicolás

2018-03-15

According to Act No. 17283 of November 28th, 2000, air quality protection is a general concern in Uruguay. Road transport is the main emitter of nitrogen oxides (NO x ), as the National Inventory of Air Emissions 2006 stated. Actually, it is responsible for the emissions of 59.8% of NO x and 28% of carbon monoxide (CO). The number of households owning a car in Uruguay increased from 29% in 2005 to 39% in 2013, enhancing the importance of characterizing the vehicular emissions of the national fleet. In this paper, a first approach for this characterization is presented. It was carried out on a sample of 11 light vehicles currently in use in Montevideo city, Uruguay. On-road emissions measurements of nitrogen monoxide (NO), carbon monoxide (CO) and carbon dioxide (CO 2 ) were carried out for calculating the emission factors. The fitness of the set of calculated emission factors values to different probability distributions was tested. When possible, the 95% confidence intervals were obtained for the mean emission factors (CO: 2.0g/km±0.3g/km; NO: 0.05g/km±0.01g/km). This procedure was useful to obtaining accurate confidence intervals from a relatively small sample size. Finally, the link between atmospheric emissions and some other parameters of the tested vehicles was studied using a multivariate statistical tool, highlighting the strong increase in carbon monoxide emissions observed for low vehicles speeds and fuel efficiencies. Copyright © 2017 Elsevier B.V. All rights reserved.

Simultaneous field measurements of biogenic emissions of nitric oxide and nitrous oxide

Science.gov (United States)

Anderson, Iris Cofman; Levine, Joel S.

1987-01-01

Seasonal and diurnal emissions of NO and N2O from agricultural sites in Jamestown, Virginia and Boulder, Colorado are estimated in terms of soil temperature; percent moisture; and exchangeable nitrate, nitrite, and ammonium concentrations. The techniques and procedures used to analyze the soil parameters are described. The spatial and temporal variability of the NO and N2O emissions is studied. A correlation between NO fluxes in the Virginia sample and nitrate concentration, temperature, and percent moisture is detected, and NO fluxes for the Colorado site correspond with temperature and moisture. It is observed that the N2O emissions are only present when percent moisture approaches or exceeds the field capacity of the soil. The data suggest that NO is produced primarily by nitrification in aerobic soils, and N2O is formed by denitrification in anaerobic soils.

Mass transfer inside a flux hood for the sampling of gaseous emissions from liquid surfaces - Experimental assessment and emission rate rescaling

Science.gov (United States)

Prata, Ademir A.; Lucernoni, Federico; Santos, Jane M.; Capelli, Laura; Sironi, Selena; Le-Minh, Nhat; Stuetz, Richard M.

2018-04-01

This study assesses the mass transfer of compounds inside the US EPA flux hood, one of the enclosure devices most commonly employed for the direct measurement of atmospheric emissions from liquid surfaces in wastewater treatment plants (WWTPs). Experiments comprised the evaporation of water and the volatilisation of a range of volatile organic compounds (VOCs). Special attention was given to the evaluation of the mass transfer coefficients in the microenvironment created by the flux hood and the effects of concentration build up in the hood's headspace. The VOCs emission rates and the water evaporation rates generally increased with the sweep air flow rate, as did the mass transfer coefficients for all compounds. The emission of compounds whose volatilisation is significantly influenced by the gas phase was greatly affected by concentration build up, whereas this effect was not significant for liquid phase-controlled compounds. The gas-film mass transfer coefficient (kG) estimated inside the US EPA flux hood was of the same order as the respective kG reported in the literature for wind tunnel-type devices, but the emission rates measured by the flux hood can be expected to be lower, due to the concentration build-up. Compared against an emission model for the passive surfaces in WWTPs, the mass transfer of acetic acid (representing a gas phase-dominated compound) inside the US EPA flux hood was equivalent to conditions of wind speeds at 10 m height (U10) of 0.27, 0.51 and 0.99 m s-1, respectively, for sweep air flow rates of 2, 5 and 10 L min-1. On the other hand, for higher wind speeds, the emission rates of gas phase-controlled compounds obtained with the flux hood can be considerably underestimated: for instance, at U10 = 5 m s-1, the emission rates of acetic acid inside the flux hood would be approximately 23, 12 and 6 times lower than the emission rates in the field, for sweep air flow rates of 2, 5 and 10 L min-1, respectively. A procedure is presented in

Improved national calculation procedures to assess energy requirements, nitrogen and VS excretions of dairy cows in the German emission model GAS-EM

DEFF Research Database (Denmark)

Dämmgen, Ulrich; Haenel, Hans-Dieter; Rösemann, Claus

2009-01-01

The calculation module for the assessment of feed intake and excretion rates of dairy cows in the German agricultural emission model GAS-EM is described in detail. The module includes the description of methane emissions from enteric fermentation as well as the assessment of volatile solids...... matter intake. The results agree well with those obtained from regression models and respective experiments. The model is able to refl ect national and regional peculiarities in dairy cow husbandry. It is an adequate tool for the establishment of emission inventories and for the construction of scenarios...

Administrative Procedure Act and mass procedures (illustrated by the nuclear licensing procedure)

International Nuclear Information System (INIS)

Naumann, R.

1977-01-01

The report deals with the administrative procedure law of 25.5.76 of the Fed. Government, esp. with its meaning for the administrative procedures for the permission for nuclear power plants, as fas ar so-called mass procedures are concerned. (UN) [de

An Iterative O-Methyltransferase Catalyzes 1,11-Dimethylation of Aspergillus fumigatus Fumaric Acid Amides.

Science.gov (United States)

Kalb, Daniel; Heinekamp, Thorsten; Schieferdecker, Sebastian; Nett, Markus; Brakhage, Axel A; Hoffmeister, Dirk

2016-10-04

S-adenosyl-l-methionine (SAM)-dependent methyltransfer is a common biosynthetic strategy to modify natural products. We investigated the previously uncharacterized Aspergillus fumigatus methyltransferase FtpM, which is encoded next to the bimodular fumaric acid amide synthetase FtpA. Structure elucidation of two new A. fumigatus natural products, the 1,11-dimethyl esters of fumaryl-l-tyrosine and fumaryl-l-phenylalanine, together with ftpM gene disruption suggested that FtpM catalyzes iterative methylation. Final evidence that a single enzyme repeatedly acts on fumaric acid amides came from an in vitro biochemical investigation with recombinantly produced FtpM. Size-exclusion chromatography indicated that this methyltransferase is active as a dimer. As ftpA and ftpM homologues are found clustered in other fungi, we expect our work will help to identify and annotate natural product biosynthesis genes in various species. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Compendium of Greenhouse Gas Emissions Estimation Methodologies for the Oil and Gas Industry

Energy Technology Data Exchange (ETDEWEB)

Shires, T.M.; Loughran, C.J. [URS Corporation, Austin, TX (United States)

2004-02-01

This document is a compendium of currently recognized methods and provides details for all oil and gas industry segments to enhance consistency in emissions estimation. This Compendium aims to accomplish the following goals: Assemble an expansive collection of relevant emission factors for estimating GHG emissions, based on currently available public documents; Outline detailed procedures for conversions between different measurement unit systems, with particular emphasis on implementation of oil and gas industry standards; Provide descriptions of the multitude of oil and gas industry operations, in its various segments, and the associated emissions sources that should be considered; and Develop emission inventory examples, based on selected facilities from the various segments, to demonstrate the broad applicability of the methodologies. The overall objective of developing this document is to promote the use of consistent, standardized methodologies for estimating GHG emissions from petroleum industry operations. The resulting Compendium documents recognized calculation techniques and emission factors for estimating GHG emissions for oil and gas industry operations. These techniques cover the calculation or estimation of emissions from the full range of industry operations - from exploration and production through refining, to the marketing and distribution of products. The Compendium presents and illustrates the use of preferred and alternative calculation approaches for carbon dioxide (CO2), methane (CH4), and nitrous oxide (N2O) emissions for all common emission sources, including combustion, vented, and fugitive. Decision trees are provided to guide the user in selecting an estimation technique based on considerations of materiality, data availability, and accuracy. API will provide (free of charge) a calculation tool based on the emission estimation methodologies described herein. The tool will be made available at http://ghg.api.org/.

Experimental Evaluation of a Low Emissions High Performance Duct Burner for Variable Cycle Engines (VCE)

Science.gov (United States)

Lohmann, R. P.; Mador, R. J.

1979-01-01

An evaluation was conducted with a three stage Vorbix duct burner to determine the performance and emissions characteristics of the concept and to refine the configuration to provide acceptable durability and operational characteristics for its use in the variable cycle engine (VCE) testbed program. The tests were conducted at representative takeoff, transonic climb, and supersonic cruise inlet conditions for the VSCE-502B study engine. The test stand, the emissions sampling and analysis equipment, and the supporting flow visualization rigs are described. The performance parameters including the fuel-air ratio, the combustion efficiency/exit temperature, thrust efficiency, and gaseous emissions calculations are defined. The test procedures are reviewed and the results are discussed.

An econometric study of CO2 emissions, energy consumption, income and foreign trade in Turkey

International Nuclear Information System (INIS)

Halicioglu, Ferda

2009-01-01

This study attempts to empirically examine the dynamic causal relationships between carbon emissions, energy consumption, income, and foreign trade in the case of Turkey using the time-series data for the period 1960-2005. This research tests the interrelationship between the variables using the bounds testing to cointegration procedure. The bounds test results indicate that there exist two forms of long-run relationships between the variables. In the case of first form of long-run relationship, carbon emissions are determined by energy consumption, income and foreign trade. In the case of second long-run relationship, income is determined by carbon emissions, energy consumption and foreign trade. An augmented form of Granger causality analysis is conducted amongst the variables. The long-run relationship of CO 2 emissions, energy consumption, income and foreign trade equation is also checked for the parameter stability. The empirical results suggest that income is the most significant variable in explaining the carbon emissions in Turkey which is followed by energy consumption and foreign trade. Moreover, there exists a stable carbon emissions function. The results also provide important policy recommendations. (author)

(reprocessed)CAGE peaks - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...g38/mm10). Data file File name: (reprocessed)CAGE_peaks (Homo sapiens) File URL: ftp://ftp.biosciencedbc.jp/archive/fantom...)CAGE_peaks (Mus musculus) File URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/d...his Database Site Policy | Contact Us (reprocessed)CAGE peaks - FANTOM5 | LSDB Archive ...

(reprocessed)pooled_ctss - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...e: (reprocessed)pooled_ctss (Homo sapiens) File URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/datafiles/re...) File URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/datafiles/reprocessed/mm10...ory of This Database Site Policy | Contact Us (reprocessed)pooled_ctss - FANTOM5 | LSDB Archive ...

Physiotherapy clinical educators? perceptions of student fitness to practise

OpenAIRE

Lo, Kristin; Curtis, Heather; Keating, Jennifer L.; Bearman, Margaret

2017-01-01

Background Health professional students are expected to maintain Fitness to Practise (FTP) including clinical competence, professional behaviour and freedom from impairment (physical/mental health). FTP potentially affects students, clinicians and clients, yet the impact of supervising students across the spectrum of FTP issues remains relatively under-reported. This study describes clinical educators? perceptions of supporting students with FTP issues. Methods Between November 2012 and Janua...

Interdisciplinary environmental impact statement examinations with parallel licensing procedures

International Nuclear Information System (INIS)

Gassner, E.

1990-01-01

The article investigates the question how the interdisciplinary, collective, integrative environmental impact statement can predominate the decisions in individual licensing procedures. It illustrates the requirements of the Act on Environmental Impact Statements. According to this Act, measures are to be found which deal with the overall complex, i.e. the entire system. In the article, the monitoring project organization's primary responsibility is emphasized: Analysis and prognosis of a project's environmental impacts are transferred to this organization for decision-preparation. Subsequent corrections or supplementations during the official approval procedure, or incorporation of the public through the authorities, do not change the matter. An all-comprehensive assessment must be based on all-comprehensive standards. From the point of view of immissions this is minimization of adverse effects on the nature cycle and landscape matters; from the point of view of emissions it is the duty of environment-compatible waste management within the sense of waste management legislation having to serve public welfare. (orig.) [de

Characterization of methane emissions from five cold heavy oil production with sands (CHOPS) facilities.

Science.gov (United States)

Roscioli, Joseph R; Herndon, Scott C; Yacovitch, Tara I; Knighton, W Berk; Zavala-Araiza, Daniel; Johnson, Matthew R; Tyner, David R

2018-03-07

Cold heavy oil production with sands (CHOPS) is a common oil extraction method in the Canadian provinces of Alberta and Saskatchewan that can result in significant methane emissions due to annular venting. Little is known about the magnitude of these emissions, nor their contributions to the regional methane budget. Here the authors present the results of field measurements of methane emissions from CHOPS wells and compare them with self-reported venting rates. The tracer ratio method was used not only to analyze total site emissions but at one site it was also used to locate primary emission sources and quantify their contributions to the facility-wide emission rate, revealing the annular vent to be a dominant source. Emissions measured from five different CHOPS sites in Alberta showed large discrepancies between the measured and reported rates, with emissions being mainly underreported. These methane emission rates are placed in the context of current reporting procedures and the role that gas-oil ratio (GOR) measurements play in vented volume estimates. In addition to methane, emissions of higher hydrocarbons were also measured; a chemical "fingerprint" associated with CHOPS wells in this region reveals very low emission ratios of ethane, propane, and aromatics versus methane. The results of this study may inform future studies of CHOPS sites and aid in developing policy to mitigate regional methane emissions. Methane measurements from cold heavy oil production with sand (CHOPS) sites identify annular venting to be a potentially major source of emissions at these facilities. The measured emission rates are generally larger than reported by operators, with uncertainty in the gas-oil ratio (GOR) possibly playing a large role in this discrepancy. These results have potential policy implications for reducing methane emissions in Alberta in order to achieve the Canadian government's goal of reducing methane emissions by 40-45% below 2012 levels within 8 yr.

Direct Final Rule for Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures

Science.gov (United States)

This rule will adopt the current voluntary NOx and CO emissions standards of the United Nations International Civil Aviation Organization (ICAO), bringing the United States aircraft standards into alignment with the international standards.

Automatic regulation of the feedwater turbo-pump capacity for the single-turbine 1000 MW NPP unit

International Nuclear Information System (INIS)

Pavlysh, O.N.; Garbuzov, I.P.; Reukov, Yu.N.

1985-01-01

A schematic of the flow regulators (FR) of feedwater turbo-pumps (FTP) for the single-turbine 1000 MW NPP unit is presented. The FR operate in response to feedwoter signals from FTP or in response to FTP rotor rotational speed and control automatic speed governars. The FR automatic regulation ensures limitation of FTP rotor maximum rotational speed at a feedwater flow rate excess equal to 3600 T/h. The transients in the automatic regulation system are considered. Production tests of FTP FR confirmed the FR operation reliability and the right choice of the regulator concept and structure

Impacts of biological and procedural factors on semiquantification uptake value of liver in fluorine-18 fluorodeoxyglucose positron emission tomography/computed tomography imaging.

Science.gov (United States)

Mahmud, Mohd Hafizi; Nordin, Abdul Jalil; Ahmad Saad, Fathinul Fikri; Azman, Ahmad Zaid Fattah

2015-10-01

Increased metabolic activity of fluorodeoxyglucose (FDG) in tissue is not only resulting of pathological uptake, but due to physiological uptake as well. This study aimed to determine the impacts of biological and procedural factors on FDG uptake of liver in whole body positron emission tomography/computed tomography (PET/CT) imaging. Whole body fluorine-18 ((18)F) FDG PET/CT scans of 51 oncology patients have been reviewed. Maximum standardized uptake value (SUVmax) of lesion-free liver was quantified in each patient. Pearson correlation was performed to determine the association between the factors of age, body mass index (BMI), blood glucose level, FDG dose and incubation period and liver SUVmax. Multivariate regression analysis was established to determine the significant factors that best predicted the liver SUVmax. Then the subjects were dichotomised into four BMI groups. Analysis of variance (ANOVA) was established for mean difference of SUVmax of liver between those BMI groups. BMI and incubation period were significantly associated with liver SUVmax. These factors were accounted for 29.6% of the liver SUVmax variance. Statistically significant differences were observed in the mean SUVmax of liver among those BMI groups (Pvalue for physiological liver SUVmax as a reference standard for different BMI of patients in PET/CT interpretation and use a standard protocol for incubation period of patient to reduce variation in physiological FDG uptake of liver in PET/CT study.

Union Gas assessment protocol for power generator air and noise emissions

International Nuclear Information System (INIS)

Complin, P.

2008-01-01

This paper outlined a procedure for obtaining data to facilitate air and noise compliance assessments for emergency and other fuel-fired power generators. Facilities with the generators may contain additional sources of nitrogen oxides (NO x ). The assessments are required for each new or modified generator in order to ensure that regulatory requirements in the Air Pollution Local Air Quality Regulation and the Noise Pollution Control documents are met. The air emission assessments follow the Ontario Ministry of the Environment (MOE) report. The paper included a screening process to screen out generators with negligible emissions. A maximum power rating was calculated using AP-2 emission factors and a conservative heat rating assumption. Maximum power ratings for various types of generators were presented. The information requirements included a description of the type of engine used; sound power level data; octave band insertion loss data; and plan and section drawings of the generator room. 2 tabs.

Benchmarking energy use and greenhouse gas emissions in Singapore's hotel industry

International Nuclear Information System (INIS)

Wu Xuchao; Priyadarsini, Rajagopalan; Eang, Lee Siew

2010-01-01

Hotel buildings are reported in many countries as one of the most energy intensive building sectors. Besides the pressure posed on energy supply, they also have adverse impact on the environment through greenhouse gas emissions, wastewater discharge and so on. This study was intended to shed some light on the energy and environment related issues in hotel industry. Energy consumption data and relevant information collected from hotels were subjected to rigorous statistical analysis. A regression-based benchmarking model was established, which takes into account, the difference in functional and operational features when hotels are compared with regard to their energy performance. In addition, CO 2 emissions from the surveyed hotels were estimated based on a standard procedure for corporate GHG emission accounting. It was found that a hotel's carbon intensity ranking is rather sensitive to the normalizing denominator chosen. Therefore, carbon intensity estimated for the hotels must not be interpreted arbitrarily, and industry specific normalizing denominator should be sought in future studies.

Gravitational wave emission from a bounded source: A treatment in the full nonlinear regime

International Nuclear Information System (INIS)

Oliveiral, H.P. de; Damiao Soares, I.

2004-03-01

The dynamics of a bounded gravitational collapsing configuration emitting gravitational waves is studied. The exterior spacetime is described by Robinson-Trautman geometries and have the Schwarzschild black hole as its final gravitational configuration, when the gravitational wave emission ceases. The full nonlinear regime is examined by using the Galerkin method that allows us to reduce the equations governing the dynamics to a finite-dimensional dynamical system, after a proper truncation procedure. Gravitational wave emission patterns from given initial configurations are exhibited for several phases of the collapse and the mass-loss ratio that characterizes the amount of mass extracted by the gravitational wave emission is evaluated. We obtain that the smaller initial mass M init of the configuration, the more rapidly the Schwarzschild solution is attained and a larger fraction of M init is lost in the process of gravitational wave emission. Within all our numerical experiments, the distribution of the mass fraction extracted by gravitational wave emission is shown to satisfy the distribution law of nonextensive statistics and this result is independent of the initial configurations considered. (author)

Emergency procedures

International Nuclear Information System (INIS)

Abd Nasir Ibrahim; Azali Muhammad; Ab Razak Hamzah; Abd Aziz Mohamed; Mohammad Pauzi Ismail

2004-01-01

The following subjects are discussed - Emergency Procedures: emergency equipment, emergency procedures; emergency procedure involving X-Ray equipment; emergency procedure involving radioactive sources

Quantum squeezed state analysis of spontaneous ultra weak light photon emission of practitioners of meditation and control subjects.

Science.gov (United States)

Van Wijk, Eduard P A; Van Wijk, Roeland; Bajpai, Rajendra P

2008-05-01

Research on human ultra-weak photon emission (UPE) has suggested a typical human emission anatomic percentage distribution pattern. It was demonstrated that emission intensities are lower in long-term practitioners of meditation as compared to control subjects. The percent contribution of emission from different anatomic locations was not significantly different for meditation practitioners and control subjects. Recently, a procedure was developed to analyze the fluctuations in the signals by measuring probabilities of detecting different numbers of photons in a bin and correct these for background noise. The procedure was tested utilizing the signal from three different body locations of a single subject, demonstrating that probabilities have non-classical features and are well described by the signal in a coherent state from the three body sites. The values indicate that the quantum state of photon emitted by the subject could be a coherent state in the subject being investigated. The objective in the present study was to systematically quantify, in subjects with long-term meditation experience and subjects without this experience, the photon count distribution of 12 different locations. Data show a variation in quantum state parameters within each individual subject as well as variation in quantum state parameters between the groups.

VLBA imaging of the 3 mm SiO maser emission in the disk-wind from the massive protostellar system Orion Source I

Science.gov (United States)

Issaoun, S.; Goddi, C.; Matthews, L. D.; Greenhill, L. J.; Gray, M. D.; Humphreys, E. M. L.; Chandler, C. J.; Krumholz, M.; Falcke, H.

2017-10-01

Context. High-mass star formation remains poorly understood due to observational difficulties (e.g. high dust extinction and large distances) hindering the resolution of disk-accretion and outflow-launching regions. Aims: Orion Source I is the closest known massive young stellar object (YSO) and exceptionally powers vibrationally-excited SiO masers at radii within 100 AU, providing a unique probe of gas dynamics and energetics. We seek to observe and image these masers with Very Long Baseline Interferometry (VLBI). Methods: We present the first images of the 28SiO v = 1, J = 2-1 maser emission around Orion Source I observed at 86 GHz (λ3 mm) with the Very Long Baseline Array (VLBA). These images have high spatial ( 0.3 mas) and spectral ( 0.054 km s-1) resolutions. Results: We find that the λ3 mm masers lie in an X-shaped locus consisting of four arms, with blue-shifted emission in the south and east arms and red-shifted emission in the north and west arms. Comparisons with previous images of the 28SiO v = 1,2, J = 1-0 transitions at λ7 mm (observed in 2001-2002) show that the bulk of the J = 2-1 transition emission follows the streamlines of the J = 1-0 emission and exhibits an overall velocity gradient consistent with the gradient at λ7 mm. While there is spatial overlap between the λ3 mm and λ7 mm transitions, the λ3 mm emission, on average, lies at larger projected distances from Source I ( 44 AU compared with 35 AU for λ7 mm). The spatial overlap between the v = 1, J = 1-0 and J = 2-1 transitions is suggestive of a range of temperatures and densities where physical conditions are favorable for both transitions of a same vibrational state. However, the observed spatial offset between the bulk of emission at λ3 mm and λ7 mm possibly indicates different ranges of temperatures and densities for optimal excitation of the masers. We discuss different maser pumping models that may explain the observed offset. Conclusions: We interpret the λ3 mm and λ7 mm

Air Emission Inventory for the INEEL -- 1999 Emission Report

Energy Technology Data Exchange (ETDEWEB)

Zohner, Steven K

2000-05-01

This report presents the 1999 calendar year update of the Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory (INEEL). The INEEL Air Emission Inventory documents sources and emissions of nonradionuclide pollutants from operations at the INEEL. The report describes the emission inventory process and all of the sources at the INEEL, and provides nonradionuclide emissions estimates for stationary sources.

(reprocessed)CAGE_peaks_annotation - FANTOM5 | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data List Contact us FANTOM...: ftp://ftp.biosciencedbc.jp/archive/fantom5/datafiles/reprocessed/hg38_latest/extra/CAGE_peaks_annotation/ ...e URL: ftp://ftp.biosciencedbc.jp/archive/fantom5/datafiles/reprocessed/mm10_latest/extra/CAGE_peaks_annotat...te History of This Database Site Policy | Contact Us (reprocessed)CAGE_peaks_annotation - FANTOM5 | LSDB Archive ...

Protocol - RPD | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data ...e version) File URL: ftp://ftp.biosciencedbc.jp/archive/rpd/LATEST/rpd_protocol_jp.zip File size: 535 KB Fil...e name: rpd_protocol_en.zip (English version) File URL: ftp://ftp.biosciencedbc.jp/archiv...tabase Database Description Download License Update History of This Database Site Policy | Contact Us Protocol - RPD | LSDB Archive ...

State-of-the art comparability of corrected emission spectra. 2. Field laboratory assessment of calibration performance using spectral fluorescence standards.

Science.gov (United States)

Resch-Genger, Ute; Bremser, Wolfram; Pfeifer, Dietmar; Spieles, Monika; Hoffmann, Angelika; DeRose, Paul C; Zwinkels, Joanne C; Gauthier, François; Ebert, Bernd; Taubert, R Dieter; Voigt, Jan; Hollandt, Jörg; Macdonald, Rainer

2012-05-01

In the second part of this two-part series on the state-of-the-art comparability of corrected emission spectra, we have extended this assessment to the broader community of fluorescence spectroscopists by involving 12 field laboratories that were randomly selected on the basis of their fluorescence measuring equipment. These laboratories performed a reference material (RM)-based fluorometer calibration with commercially available spectral fluorescence standards following a standard operating procedure that involved routine measurement conditions and the data evaluation software LINKCORR developed and provided by the Federal Institute for Materials Research and Testing (BAM). This instrument-specific emission correction curve was subsequently used for the determination of the corrected emission spectra of three test dyes, X, QS, and Y, revealing an average accuracy of 6.8% for the corrected emission spectra. This compares well with the relative standard uncertainties of 4.2% for physical standard-based spectral corrections demonstrated in the first part of this study (previous paper in this issue) involving an international group of four expert laboratories. The excellent comparability of the measurements of the field laboratories also demonstrates the effectiveness of RM-based correction procedures.

Particulate emissions calculations from fall tillage operations using point and remote sensors.

Science.gov (United States)

Moore, Kori D; Wojcik, Michael D; Martin, Randal S; Marchant, Christian C; Bingham, Gail E; Pfeiffer, Richard L; Prueger, John H; Hatfield, Jerry L

2013-07-01

Soil preparation for agricultural crops produces aerosols that may significantly contribute to seasonal atmospheric particulate matter (PM). Efforts to reduce PM emissions from tillage through a variety of conservation management practices (CMPs) have been made, but the reductions from many of these practices have not been measured in the field. A study was conducted in California's San Joaquin Valley to quantify emissions reductions from fall tillage CMP. Emissions were measured from conventional tillage methods and from a "combined operations" CMP, which combines several implements to reduce tractor passes. Measurements were made of soil moisture, bulk density, meteorological profiles, filter-based total suspended PM (TSP), concentrations of PM with an equivalent aerodynamic diameter ≤10 μm (PM) and PM with an equivalent aerodynamic diameter ≤2.5 μm (PM), and aerosol size distribution. A mass-calibrated, scanning, three-wavelength light detection and ranging (LIDAR) procedure estimated PM through a series of algorithms. Emissions were calculated via inverse modeling with mass concentration measurements and applying a mass balance to LIDAR data. Inverse modeling emission estimates were higher, often with statistically significant differences. Derived PM emissions for conventional operations generally agree with literature values. Sampling irregularities with a few filter-based samples prevented calculation of a complete set of emissions through inverse modeling; however, the LIDAR-based emissions dataset was complete. The CMP control effectiveness was calculated based on LIDAR-derived emissions to be 29 ± 2%, 60 ± 1%, and 25 ± 1% for PM, PM, and TSP size fractions, respectively. Implementation of this CMP provides an effective method for the reduction of PM emissions. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

2006 LANL Radionuclide Air Emissions Report

Energy Technology Data Exchange (ETDEWEB)

David P. Fuehne

2007-06-30

This report describes the impacts from emissions of radionuclides at Los Alamos National Laboratory (LANL) for calendar year 2006. This report fulfills the requirements established by the Radionuclide National Emissions Standards for Hazardous Air Pollutants (Rad-NESHAP). This report is prepared by LANL's Rad-NESHAP compliance team, part of the Environmental Protection Division. The information in this report is required under the Clean Air Act and is being reported to the U.S. Environmental Protection Agency (EPA). The highest effective dose equivalent (EDE) to an off-site member of the public was calculated using procedures specified by the EPA and described in this report. LANL's EDE was 0.47 mrem for 2006. The annual limit established by the EPA is 10 mrem per year. During calendar year 2006, LANL continuously monitored radionuclide emissions at 28 release points, or stacks. The Laboratory estimates emissions from an additional 58 release points using radionuclide usage source terms. Also, LANL uses a network of air samplers around the Laboratory perimeter to monitor ambient airborne levels of radionuclides. To provide data for dispersion modeling and dose assessment, LANL maintains and operates meteorological monitoring systems. From these measurement systems, a comprehensive evaluation is conducted to calculate the EDE for the Laboratory. The EDE is evaluated as any member of the public at any off-site location where there is a residence, school, business, or office. In 2006, this location was the Los Alamos Airport Terminal. The majority of this dose is due to ambient air sampling of plutonium emitted from 2006 clean-up activities at an environmental restoration site (73-002-99; ash pile). Doses reported to the EPA for the past 10 years are shown in Table E1.

Study of the nucleotide binding site of the yeast Schizosaccharomyces pombe plasma membrane H+-ATPase using formycin triphosphate-terbium complex

International Nuclear Information System (INIS)

Ronjat, M.; Lacapere, J.J.; Dufour, J.P.; Dupont, Y.

1987-01-01

The plasma membrane of yeasts contains an H+-ATPase similar to the other cation transport ATPases of eukaryotic organisms. This enzyme has been purified and shows H+ transport in reconstituted vesicles. In the presence of Mg2+, formycin triphosphate (FTP) is hydrolyzed by the H+-ATPase and supports H+ transport. When combined with terbium ion, FTP (Tb-FTP) and ATP (Tb-ATP) are no longer hydrolyzed. Competition between Mg-ATP and Tb-FTP for ATP hydrolysis indicates that terbium-associated nucleotides bind to the catalytic site of the H+-ATPase. The fluorescent properties of the Tb-FTP complex were used to study the active site of the H+-ATPase. Fluorescence of Tb-FTP is greatly enhanced upon binding into the nucleotide site of H+-ATPase with a dissociation constant of 1 microM. Tb-ATP, Tb-ADP, and Tb-ITP are competitive inhibitors of Tb-FTP binding with Ki = 4.5, 5.0, and 6.0 microM, respectively. Binding of Tb-FTP is observed only in the presence of an excess of Tb3+ with an activation constant Ka = 25 microM for Tb3+. Analysis of the data reveals that the sites for Tb-FTP and Tb3+ binding are independent entities. In standard conditions these sites would be occupied by Mg-ATP and Mg2+, respectively. These findings suggest an important regulatory role of divalent cations on the activity of H+-ATPase. Replacement of H 2 O by D 2 O in the medium suggests the existence of two types of nucleotide binding sites differing by the hydration state of the Tb3+ ion in the bound Tb-FTP complex

Carbon emissions and an equitable emission reduction criterion

International Nuclear Information System (INIS)

Golomb, Dan

1999-01-01

In 1995 the world-wide carbon emissions reached 5.8 billion metric tonnes per year (GTC/y). The Kyoto protocol calls for a reduction of carbon emissions from the developed countries (Annex I countries) of 6-8% below 1990 levels on the average, and unspecified commitments for the less developed (non-Annex I) countries. It is doubtful that the Kyoto agreement will be ratified by some parliaments, especially the USA Congress. Furthermore, it is shown that if the non-Annex I countries will not curtail their carbon emissions drastically, the global emissions will soar to huge levels by the middle of the next century. An equitable emission criterion is proposed which may lead to a sustainable rate of growth of carbon emissions, and be acceptable to all countries of the world. The criterion links the rate of growth of carbon emissions to the rate of growth of the Gross Domestic Product (GDP). A target criterion is proposed R = 0.15 KgC/SGDP, which is the current average for western European countries and Japan. This allows for both the growth of the GDP and carbon emissions. However, to reach the target in a reasonable time, the countries for which R≤ 0.3 would be allowed a carbon emission growth rate of 1%./y, and countries for which R≥ 0.3, 0.75%/y. It is shown that by 2050 the world-wide carbon emissions would reach about 10 GTC/y, which is about 3 times less than the Kyoto agreement would allow. (Author)

Self-consistent two-phase AGN torus models⋆. SED library for observers

Science.gov (United States)

Siebenmorgen, Ralf; Heymann, Frank; Efstathiou, Andreas

2015-11-01

We assume that dust near active galactic nuclei (AGNs) is distributed in a torus-like geometry, which can be described as a clumpy medium or a homogeneous disk, or as a combination of the two (i.e. a two-phase medium). The dust particles considered are fluffy and have higher submillimeter emissivities than grains in the diffuse interstellar medium. The dust-photon interaction is treated in a fully self-consistent three-dimensional radiative transfer code. We provide an AGN library of spectral energy distributions (SEDs). Its purpose is to quickly obtain estimates of the basic parameters of the AGNs, such as the intrinsic luminosity of the central source, the viewing angle, the inner radius, the volume filling factor and optical depth of the clouds, and the optical depth of the disk midplane, and to predict the flux at yet unobserved wavelengths. The procedure is simple and consists of finding an element in the library that matches the observations. We discuss the general properties of the models and in particular the 10 μm silicate band. The AGN library accounts well for the observed scatter of the feature strengths and wavelengths of the peak emission. AGN extinction curves are discussed and we find that there is no direct one-to-one link between the observed extinction and the wavelength dependence of the dust cross sections. We show that objects in the library cover the observed range of mid-infrared colors of known AGNs. The validity of the approach is demonstrated by matching the SEDs of a number of representative objects: Four Seyferts and two quasars for which we present new Herschel photometry, two radio galaxies, and one hyperluminous infrared galaxy. Strikingly, for the five luminous objects we find that pure AGN models fit the SED without needing to postulate starburst activity. Herschel is an ESA space observatory with science instruments provided by European-led Principal Investigator consortia and with important participation from NASA.The SED

Emission Inventory for Fugitive Emissions in Denmark

DEFF Research Database (Denmark)

Plejdrup, Marlene Schmidt; Nielsen, Ole-Kenneth; Nielsen, Malene

This report presents the methodology and data used in the Danish inventory of fugitive emissions from fuels for the years until 2007. The inventory of fugitive emissions includes CO2, CH4, N2O, NOx, CO, NMVOC, SO2, dioxin, PAH and particulate matter. In 2007 the total Danish emission of greenhouse...

Calculations of total fusion power and spatial distribution of emissivity for a D-T thermal plasma

International Nuclear Information System (INIS)

Batistoni, P.; Pillon, M.

1987-01-01

The preliminary project of a diagnostic tool to measure the neutron emissivity profile for NET (Next European Torus) with an array of collimators is presented. With the help of a neutron transport code the maximum possible number of collimators, compatible with the crosstalk noise and the space available in the NET 2.2.B is determined within these constraints. An array of 17 collimators can be used, and some experimental results are simulated using a Monte Carlo code. These results are analyzed and an inversion procedure is used to obtain the emissivity profile and evaluate the total fusion power. The results show that the total fusion power can be measured within 10% for different emission profiles

Use of positron emission tomography in colorectal cancer

International Nuclear Information System (INIS)

Gonzalez E, Patricio; Jofre E, Josefina; Massardo V, Teresa; Humeres, Pamela; Canessa G, Jose; Sierralta C, Paulina

2002-01-01

The value of PET (Positron Emission Tomography) in colorectal cancer is presented. PET is a novel technique that uses F-18-FDG (fluorodeoxiglucose) to assess glucose metabolism by whole body imaging. It has been demonstrated that malignant cells have both increase of glucose uptake and utilization. In colorectal cancer, PET is indicated for staging, assess recurrence, liver metastasis and treatment follow-up. PET is more sensitive and specific than CT (Computed Tomography) and is cost effective. In 30% of cases PET may change patient management, avoiding unnecessary procedures (au)

Characterization of aerosols produced by surgical procedures

Energy Technology Data Exchange (ETDEWEB)

Yeh, H.C.; Muggenburg, B.A.; Lundgren, D.L.; Guilmette, R.A.; Snipes, M.B.; Jones, R.K. [Inhalation Toxicology Research Institute, Albuquerque, NM (United States); Turner, R.S. [Lovelace Health Systems, Albuquerque, NM (United States)

1994-07-01

In many surgeries, especially orthopedic procedures, power tools such as saws and drills are used. These tools may produce aerosolized blood and other biological material from bone and soft tissues. Surgical lasers and electrocautery tools can also produce aerosols when tissues are vaporized and condensed. Studies have been reported in the literature concerning production of aerosols during surgery, and some of these aerosols may contain infectious material. Garden et al. (1988) reported the presence of papilloma virus DNA in the fumes produced from laser surgery, but the infectivity of the aerosol was not assessed. Moon and Nininger (1989) measured the size distribution and production rate of emissions from laser surgery and found that particles were generally less than 0.5 {mu}m diameter. More recently there has been concern expressed over the production of aerosolized blood during surgical procedures that require power tools. In an in vitro study, the production of an aerosol containing the human immunodeficiency virus (HIV) was reported when power tools were used to cut tissues with blood infected with HIV. Another study measured the size distribution of blood aerosols produced by surgical power tools and found blood-containing particles in a number of size ranges. Health care workers are anxious and concerned about whether surgically produced aerosols are inspirable and can contain viable pathogens such as HIV. Other pathogens such as hepatitis B virus (HBV) are also of concern. The Occupational Safety and Health funded a project at the National Institute for Inhalation Toxicology Research Institute to assess the extent of aerosolization of blood and other tissues during surgical procedures. This document reports details of the experimental and sampling approach, methods, analyses, and results on potential production of blood-associated aerosols from surgical procedures in the laboratory and in the hospital surgical suite.