A Delphi study assessing the utility of quality improvement tools and resources in Australian primary care.

Science.gov (United States)

Upham, Susan J; Janamian, Tina; Crossland, Lisa; Jackson, Claire L

2016-04-18

To determine the relevance and utility of online tools and resources to support organisational performance development in primary care and to complement the Primary Care Practice Improvement Tool (PC-PIT). A purposively recruited Expert Advisory Panel of 12 end users used a modified Delphi technique to evaluate 53 tools and resources identified through a previously conducted systematic review. The panel comprised six practice managers and six general practitioners who had participated in the PC-PIT pilot study in 2013-2014. Tools and resources were reviewed in three rounds using a standard pre-tested assessment form. Recommendations, scores and reasons for recommending or rejecting each tool or resource were analysed to determine the final suite of tools and resources. The evaluation was conducted from November 2014 to August 2015. Recommended tools and resources scored highly (mean score, 16/20) in Rounds 1 and 2 of review (n = 25). These tools and resources were perceived to be easily used, useful to the practice and supportive of the PC-PIT. Rejected resources scored considerably lower (mean score, 5/20) and were noted to have limitations such as having no value to the practice and poor utility (n = 6). A final review (Round 3) of 28 resources resulted in a suite of 21 to support the elements of the PC-PIT. This suite of tools and resources offers one approach to supporting the quality improvement initiatives currently in development in primary care reform.

Using perinatal morbidity scoring tools as a primary study outcome.

Science.gov (United States)

Hutcheon, Jennifer A; Bodnar, Lisa M; Platt, Robert W

2017-11-01

Perinatal morbidity scores are tools that score or weight different adverse events according to their relative severity. Perinatal morbidity scores are appealing for maternal-infant health researchers because they provide a way to capture a broad range of adverse events to mother and newborn while recognising that some events are considered more serious than others. However, they have proved difficult to implement as a primary outcome in applied research studies because of challenges in testing if the scores are significantly different between two or more study groups. We outline these challenges and describe a solution, based on Poisson regression, that allows differences in perinatal morbidity scores to be formally evaluated. The approach is illustrated using an existing maternal-neonatal scoring tool, the Adverse Outcome Index, to evaluate the safety of labour and delivery before and after the closure of obstetrical services in small rural communities. Applying the proposed Poisson regression to the case study showed a protective risk ratio for adverse outcome following closures as compared with the original analysis, where no difference was found. This approach opens the door for considerably broader use of perinatal morbidity scoring tools as a primary outcome in applied population and clinical maternal-infant health research studies. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

5As Team obesity intervention in primary care: development and evaluation of shared decision-making weight management tools.

Science.gov (United States)

Osunlana, A M; Asselin, J; Anderson, R; Ogunleye, A A; Cave, A; Sharma, A M; Campbell-Scherer, D L

2015-08-01

Despite several clinical practice guidelines, there remains a considerable gap in prevention and management of obesity in primary care. To address the need for changing provider behaviour, a randomized controlled trial with convergent mixed method evaluation, the 5As Team (5AsT) study, was conducted. As part of the 5AsT intervention, the 5AsT tool kit was developed. This paper describes the development process and evaluation of these tools. Tools were co-developed by the multidisciplinary research team and the 5AsT, which included registered nurses/nurse practitioners (n = 15), mental health workers (n = 7) and registered dieticians (n = 7), who were previously randomized to the 5AsT intervention group at a primary care network in Edmonton, Alberta, Canada. The 5AsT tool development occurred through a practice/implementation-oriented, need-based, iterative process during learning collaborative sessions of the 5AsT intervention. Feedback during tool development was received through field notes and final provider evaluation was carried out through anonymous questionnaires. Twelve tools were co-developed with 5AsT. All tools were evaluated as either 'most useful' or 'moderately useful' in primary care practice by the 5AsT. Four key findings during 5AsT tool development were the need for: tools that were adaptive, tools to facilitate interdisciplinary practice, tools to help patients understand realistic expectations for weight loss and shared decision-making tools for goal setting and relapse prevention. The 5AsT tools are primary care tools which extend the utility of the 5As of obesity management framework in clinical practice. © 2015 The Authors. Clinical Obesity published by John Wiley & Sons Ltd on behalf of World Obesity.

Experimental study on internal cooling system in hard turning of HCWCI using CBN tools

Science.gov (United States)

Ravi, A. M.; Murigendrappa, S. M.

2018-04-01

In recent times, hard turning became most emerging technique in manufacturing processes, especially to cut high hard materials like high chrome white cast iron (HCWCI). Use of Cubic boron nitride (CBN), pCBN and Carbide tools are most appropriate to shear the metals but are uneconomical. Since hard turning carried out in dry condition, lowering the tool wear by minimizing tool temperature is the only solution. Study reveals, no effective cooling systems are available so for in order to enhance the tool life of the cutting tools and to improve machinability characteristics. The detrimental effect of cutting parameters on cutting temperature is generally controlled by proper selections. The objective of this paper is to develop a new cooling system to control tool tip temperature, thereby minimizing the cutting forces and the tool wear rates. The materials chosen for this work was HCWCI and cutting tools are CBN inserts. Intricate cavities were made on the periphery of the tool holder for easy flow of cold water. Taguchi techniques were adopted to carry out the experimentations. The experimental results confirm considerable reduction in the cutting forces and tool wear rates.

Quasi-Experimental Evaluation of a National Primary School HIV Intervention in Kenya

Science.gov (United States)

Maticka-Tyndale, Eleanor; Wildish, Janet; Gichuru, Mary

2007-01-01

This study examined the impact of a primary-school HIV education initiative on the knowledge, self-efficacy and sexual and condom use activities of upper primary-school pupils in Kenya. A quasi-experimental mixed qualitative-quantitative pre- and 18-month post-design using 40 intervention and 40 matched control schools demonstrated significant…

Development of a quality-assessment tool for experimental bruxism studies: reliability and validity

NARCIS (Netherlands)

Dawson, A.; Raphael, K.G.; Glaros, A.; Axelsson, S.; Arima, T.; Ernberg, M.; Farella, M.; Lobbezoo, F.; Manfredini, D.; Michelotti, A.; Svensson, P.; List, T.

2013-01-01

AIMS: To combine empirical evidence and expert opinion in a formal consensus method in order to develop a quality-assessment tool for experimental bruxism studies in systematic reviews. METHODS: Tool development comprised five steps: (1) preliminary decisions, (2) item generation, (3) face-validity

Experimental Validation of a Wave Energy Converter Array Hydrodynamics Tool

DEFF Research Database (Denmark)

Ruiz, Pau Mercadé; Ferri, Francesco; Kofoed, Jens Peter

2017-01-01

This paper uses experimental data to validate a wave energy converter (WEC) array hydrodynamics tool developed within the context of linearized potential flow theory. To this end, wave forces and power absorption by an array of five-point absorber WECs in monochromatic and panchromatic waves were...

Developmental screening tools: feasibility of use at primary healthcare level in low- and middle-income settings.

Science.gov (United States)

Fischer, Vinicius Jobim; Morris, Jodi; Martines, José

2014-06-01

An estimated 150 million children have a disability. Early identification of developmental disabilities is a high priority for the World Health Organization to allow action to reduce impairments through Gap Action Program on mental health. The study identified the feasibility of using the developmental screening and monitoring tools for children aged 0-3 year(s) by non-specialist primary healthcare providers in low-resource settings. A systematic review of the literature was conducted to identify the tools, assess their psychometric properties, and feasibility of use in low- and middle-income countries (LMICs). Key indicators to examine feasibility in LMICs were derived from a consultation with 23 international experts. We identified 426 studies from which 14 tools used in LMICs were extracted for further examination. Three tools reported adequate psychometric properties and met most of the feasibility criteria. Three tools appear promising for use in identifying and monitoring young children with disabilities at primary healthcare level in LMICs. Further research and development are needed to optimize these tools.

Experimental anti-GBM disease as a tool for studying spontaneous lupus nephritis.

Science.gov (United States)

Fu, Yuyang; Du, Yong; Mohan, Chandra

2007-08-01

Lupus nephritis is an immune-mediated disease, where antibodies and T cells both play pathogenic roles. Since spontaneous lupus nephritis in mouse models takes 6-12 months to manifest, there is an urgent need for a mouse model that can be used to delineate the pathogenic processes that lead to immune nephritis, over a quicker time frame. We propose that the experimental anti-glomerular basement membrane (GBM) disease model might be a suitable tool for uncovering some of the molecular steps underlying lupus nephritis. This article reviews the current evidence that supports the use of the experimental anti-GBM nephritis model for studying spontaneous lupus nephritis. Importantly, out of about 25 different molecules that have been specifically examined in the experimental anti-GBM model and also spontaneous lupus nephritis, all influence both diseases concordantly, suggesting that the experimental model might be a useful tool for unraveling the molecular basis of spontaneous lupus nephritis. This has important clinical implications, both from the perspective of genetic susceptibility as well as clinical therapeutics.

Screening of Gas-Cooled Reactor Thermal-Hydraulic and Safety Analysis Tools and Experimental Database

International Nuclear Information System (INIS)

Lee, Won Jae; Kim, Min Hwan; Lee, Seung Wook

2007-08-01

This report is a final report of I-NERI Project, 'Screening of Gas-cooled Reactor Thermal Hydraulic and Safety Analysis Tools and Experimental Database 'jointly carried out by KAERI, ANL and INL. In this study, we developed the basic technologies required to develop and validate the VHTR TH/safety analysis tools and evaluated the TH/safety database information. The research tasks consist of; 1) code qualification methodology (INL), 2) high-level PIRTs for major nucleus set of events (KAERI, ANL, INL), 3) initial scaling and scoping analysis (ANL, KAERI, INL), 4) filtering of TH/safety tools (KAERI, INL), 5) evaluation of TH/safety database information (KAERI, INL, ANL) and 6) key scoping analysis (KAERI). The code qualification methodology identifies the role of PIRTs in the R and D process and the bottom-up and top-down code validation methods. Since the design of VHTR is still evolving, we generated the high-level PIRTs referencing 600MWth block-type GT-MHR and 400MWth pebble-type PBMR. Nucleus set of events that represents the VHTR safety and operational transients consists of the enveloping scenarios of HPCC (high pressure conduction cooling: loss of primary flow), LPCC/Air-Ingress (low pressure conduction cooling: loss of coolant), LC (load changes: power maneuvering), ATWS (anticipated transients without scram: reactivity insertion), WS (water ingress: water-interfacing system break) and HU (hydrogen-side upset: loss of heat sink). The initial scaling analysis defines dimensionless parameters that need to be reflected in mixed convection modeling and the initial scoping analysis provided the reference system transients used in the PIRTs generation. For the PIRTs phenomena, we evaluated the modeling capability of the candidate TH/safety tools and derived a model improvement need. By surveying and evaluating the TH/safety database information, a tools V and V matrix has been developed. Through the key scoping analysis using available database, the modeling

Screening of Gas-Cooled Reactor Thermal-Hydraulic and Safety Analysis Tools and Experimental Database

Energy Technology Data Exchange (ETDEWEB)

Lee, Won Jae; Kim, Min Hwan; Lee, Seung Wook (and others)

2007-08-15

This report is a final report of I-NERI Project, 'Screening of Gas-cooled Reactor Thermal Hydraulic and Safety Analysis Tools and Experimental Database 'jointly carried out by KAERI, ANL and INL. In this study, we developed the basic technologies required to develop and validate the VHTR TH/safety analysis tools and evaluated the TH/safety database information. The research tasks consist of; 1) code qualification methodology (INL), 2) high-level PIRTs for major nucleus set of events (KAERI, ANL, INL), 3) initial scaling and scoping analysis (ANL, KAERI, INL), 4) filtering of TH/safety tools (KAERI, INL), 5) evaluation of TH/safety database information (KAERI, INL, ANL) and 6) key scoping analysis (KAERI). The code qualification methodology identifies the role of PIRTs in the R and D process and the bottom-up and top-down code validation methods. Since the design of VHTR is still evolving, we generated the high-level PIRTs referencing 600MWth block-type GT-MHR and 400MWth pebble-type PBMR. Nucleus set of events that represents the VHTR safety and operational transients consists of the enveloping scenarios of HPCC (high pressure conduction cooling: loss of primary flow), LPCC/Air-Ingress (low pressure conduction cooling: loss of coolant), LC (load changes: power maneuvering), ATWS (anticipated transients without scram: reactivity insertion), WS (water ingress: water-interfacing system break) and HU (hydrogen-side upset: loss of heat sink). The initial scaling analysis defines dimensionless parameters that need to be reflected in mixed convection modeling and the initial scoping analysis provided the reference system transients used in the PIRTs generation. For the PIRTs phenomena, we evaluated the modeling capability of the candidate TH/safety tools and derived a model improvement need. By surveying and evaluating the TH/safety database information, a tools V and V matrix has been developed. Through the key scoping analysis using available database, the

Mind tools contributing to an ICT-rich learning environment for technology education en primary schools

NARCIS (Netherlands)

Lou A.M.P. Slangen; Peter B. Sloep

2005-01-01

This paper examines how the learning environment in primary education can be enhanced by stimulating the use of innovative ICT applications. In particular, this discussion focuses on mind tools as a means of leveraging ICT for the development of cognitive skills. The stimulating effect of mind tools

Experimental and computational tools for analysis of signaling networks in primary cells

DEFF Research Database (Denmark)

Schoof, Erwin M; Linding, Rune

2014-01-01

Cellular information processing in signaling networks forms the basis of responses to environmental stimuli. At any given time, cells receive multiple simultaneous input cues, which are processed and integrated to determine cellular responses such as migration, proliferation, apoptosis, or differ......Cellular information processing in signaling networks forms the basis of responses to environmental stimuli. At any given time, cells receive multiple simultaneous input cues, which are processed and integrated to determine cellular responses such as migration, proliferation, apoptosis......; this information is critical when trying to elucidate key proteins involved in specific cellular responses. Here, methods to generate high-quality quantitative phosphorylation data from cell lysates originating from primary cells, and how to analyze the generated data to construct quantitative signaling network...

Modal Analysis and Experimental Determination of Optimum Tool Shank Overhang of a Lathe Machine

Directory of Open Access Journals (Sweden)

Nabin SARDAR

2008-12-01

Full Text Available Vibration of Tool Shank of a cutting tool has large influence on tolerances and surface finish of products. Frequency and amplitude of vibrations depend on the overhang of the shank of the cutting tool. In turning operations, when the tool overhang is about 2 times of the tool height, the amplitude of the vibration is almost zero and dimensional tolerances and surface finish of the product becomes high. In this paper, the above statement is verified firstly by using a finite element analysis of the cutting tool with ANSYS software package and secondly, with experimental verification with a piezoelectric sensor.

Experimental research on the durability cutting tools for cutting-off steel profiles

Directory of Open Access Journals (Sweden)

Cristea Alexandru

2017-01-01

Full Text Available The production lines used for manufacturing U-shaped profiles are very complex and they must have high productivity. One of the most important stages of the fabrication process is the cutting-off. This paper presents the experimental research and analysis of the durability of the cutting tools used for cutting-off U-shaped metal steel profiles. The results of this work can be used to predict the durability of the cutting tools.

Preliminary Validation of a Screening Tool for Adolescent Panic Disorder in Pediatric Primary Care Clinics

Science.gov (United States)

Queen, Alexander H.; Ehrenreich-May, Jill; Hershorin, Eugene R.

2012-01-01

This study examines the validity of a brief screening tool for adolescent panic disorder (PD) in a primary care setting. A total of 165 participants (ages 12-17 years) seen in two pediatric primary care clinics completed the Autonomic Nervous System Questionnaire (ANS; Stein et al. in Psychosomatic Med 61:359-364, 40). A subset of those screening…

Adverse events analysis as an educational tool to improve patient safety culture in primary care: a randomized trial.

Science.gov (United States)

González-Formoso, Clara; Martín-Miguel, María Victoria; Fernández-Domínguez, Ma José; Rial, Antonio; Lago-Deibe, Fernando Isidro; Ramil-Hermida, Luis; Pérez-García, Margarita; Clavería, Ana

2011-06-14

Patient safety is a leading item on the policy agenda of both major international health organizations and advanced countries generally. The quantitative description of the phenomena has given rise to intense concern with the issue in institutions and organizations, leading to a number of initiatives and research projects and the promotion of patient safety culture, with training becoming a priority both in Spain and internationally. To date, most studies have been conducted in a hospital setting, even though primary care is the type most commonly used by the public, in our experience. Our study aims to achieve the following:--Assess the registry of adverse events as an education tool to improve patient safety culture in the Family and Community Teaching Units of Galicia.--Find and analyze educational tools to improve patient safety culture in primary care.--Evaluate the applicability of the Hospital Survey on Patient Safety Culture by the Agency for Healthcare Research and Quality, Spanish version, in the context of primary health care. Experimental unifactorial study of two groups, control and intervention. Tutors and residents in Family and Community Medicine in last year of studies in Galicia, Spain. From the population universe through voluntary participation. Twenty-seven tutor-resident units in each group required, randomly assigned. Residents and their respective tutor (tutor-resident pair) in teaching units on Family and Community Medicine from throughout Galicia will be invited to participate. Tutor-resident pair that agrees to participate will be sent the Hospital Survey on Patient Safety Culture. Then, tutor-resident pair will be assigned to each group--either intervention or control--through simple random sampling. The intervention group will receive specific training to record the adverse effects found in patients under their care, with subsequent feedback, after receiving instruction on the process. No action will be taken in the control group. After

Primary Productivity, SeaWiFS and Pathfinder, 0.1 degrees, Global, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Primary Productivity is calculated from SeaWiFS Chl a, Pathfinder SST, and SeaWiFS PAR data. THIS IS AN EXPERIMENTAL PRODUCT: intended strictly for scientific...

Video Analysis of Projectile Motion Using Tablet Computers as Experimental Tools

Science.gov (United States)

Klein, P.; Gröber, S.; Kuhn, J.; Müller, A.

2014-01-01

Tablet computers were used as experimental tools to record and analyse the motion of a ball thrown vertically from a moving skateboard. Special applications plotted the measurement data component by component, allowing a simple determination of initial conditions and "g" in order to explore the underlying laws of motion. This experiment…

Office-Based Tools and Primary Care Visit Communication, Length, and Preventive Service Delivery.

Science.gov (United States)

Lafata, Jennifer Elston; Shay, L Aubree; Brown, Richard; Street, Richard L

2016-04-01

The use of physician office-based tools such as electronic health records (EHRs), health risk appraisal (HRA) instruments, and written patient reminder lists is encouraged to support efficient, high-quality, patient-centered care. We evaluate the association of exam room use of EHRs, HRA instruments, and self-generated written patient reminder lists with patient-physician communication behaviors, recommended preventive health service delivery, and visit length. Observational study of 485 office visits with 64 primary care physicians practicing in a health system serving the Detroit metropolitan area. Study data were obtained from patient surveys, direct observation, office visit audio-recordings, and automated health system records. Outcome measures included visit length in minutes, patient use of active communication behaviors, physician use of supportive talk and partnership-building communication behaviors, and percentage of delivered guideline-recommended preventive health services for which patients are eligible and due. Simultaneous linear regression models were used to evaluate associations between tool use and outcomes. Adjusted models controlled for patient characteristics, physician characteristics, characteristics of the relationship between the patient and physician, and characteristics of the environment in which the visit took place. Prior to adjusting for other factors, visits in which the EHR was used on average were significantly (p communication behaviors facilitating patient involvement (2.1 vs. 2.6 occurrences), but more use of active patient communication behaviors (4.4 vs. 2.6). Likewise, HRA use was significantly associated with increased preventive services delivery (62.1 percent vs. 57.0 percent). All relationships remained significant (p > .05) in adjusted models with the exception of that between HRA use and preventive service delivery. Office-based tools intended to facilitate the implementation of desired primary care practice

Impact of the implementation of an online network support tool among clinicians of primary health care and specialists: ECOPIH Project.

Science.gov (United States)

Lacasta Tintorer, David; Flayeh Beneyto, Souhel; Alzaga Reig, Xavier; Mundet Tuduri, Xavier; De la Fuente, Josep Anton; Manresa, Josep Maria; Torán Monserrat, Pere; Saigí Rubió, Francesc

2013-10-03

There has been created an online communication tool with the objective to improve the communication among different levels of care, between Primary Care clinicians and Specialists. This tool is web 2.0 based technology (ECOPIH project). It allows to review clinical cases and to share knowledge. Our study will evaluate its impact in terms of reduction on the number of referrals to three specialties two years after the use of this tool. Open, multicenter, controlled, non random intervention study over 24 months. Study population includes 131 Primary Care Physicians assigned to nine health centers. The study will compare the clinicians that use the ECOPIH with the ones that do not use the tool. Also, professionals that start to use the tool during the period time of the study will be included.The number of annual referrals during the first and second year will be analyzed and retrospectively compared with the previous year to the implementation of the tool. Moreover, it will be assessed the level of satisfaction of the professionals with the tool and to what extend the tool responds to their needs. The implementation of ECOPIH in the field of Primary Health Care can decrease the number of referrals from primary care to specialist care.It is expected that the reduction will be more noticeable in the group of professionals that use more intensively the tool. Furthermore, we believe that it can be also observed with the professionals that read the contributions of the others.We anticipate high degree of customer satisfaction as it is a very helpful resource never used before in our environment.

The effects of a digital formative assessment tool on mathematics achievement and student motivation : Results of a randomized experiment

NARCIS (Netherlands)

Faber, Janke; Luyten, Johannes W.; Visscher, Arend J.

2017-01-01

In this study a randomized experimental design was used to examine the effects of a digital formative assessment tool on mathematics achievement and motivation in grade three primary education (n schools = 79, n students = 1808). Experimental schools used a digital formative assessment tool whereas

Exploring Community Philosophy as a Tool for Parental Engagement in a Primary School

Science.gov (United States)

Haines Lyon, Charlotte

2015-01-01

In this paper, I will reflect on the initial reconnaissance, action, and reflection cycle of my doctoral research, exploring Community Philosophy as a tool for critical parental engagement in a primary school (Elliot, 1991). I will examine how I reflexively engaged with my influence on participants, which then significantly influenced the framing…

The HMGU thoron experimental house: A new tool for exposure assessment

International Nuclear Information System (INIS)

Tschiersch, J.; Meisenberg, O.

2010-01-01

A thoron experimental house was constructed in a laboratory room of Helmholtz Zentrum Muenchen to perform exposure studies of thoron and its decay products under controlled conditions. The single room house (7.1 m 3 ) was built from unfired clay stones and clay plaster. For the plaster of the inner side, the clay was mixed with granite powder enriched with 232 Th. The thoron inventory increased by this means to about 1700 Bq and the progeny potential alpha energy to 130 μJ inside the room. The instrumentation of the experimental house includes active and passive devices for thoron and thoron decay product measurement including attached and unattached progeny, for aerosol particle number and size measurement and characterisation of the climatic conditions. Various parameters as ventilation rate and aerosol concentration can be adjusted. Experiments performed in the experimental house demonstrate the experimental power of this new tool for indoor thoron exposure assessment 2010. (authors)

Primary Productivity, NASA Aqua MODIS and GOES Imager, 0.1 degrees, Global, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Primary Productivity is calculated from NASA Aqua MODIS Chl a and NOAA GOES Imager SST data. THIS IS AN EXPERIMENTAL PRODUCT: intended strictly for scientific...

Quality tools and resources to support organisational improvement integral to high-quality primary care: a systematic review of published and grey literature.

Science.gov (United States)

Janamian, Tina; Upham, Susan J; Crossland, Lisa; Jackson, Claire L

2016-04-18

To conduct a systematic review of the literature to identify existing online primary care quality improvement tools and resources to support organisational improvement related to the seven elements in the Primary Care Practice Improvement Tool (PC-PIT), with the identified tools and resources to progress to a Delphi study for further assessment of relevance and utility. Systematic review of the international published and grey literature. CINAHL, Embase and PubMed databases were searched in March 2014 for articles published between January 2004 and December 2013. GreyNet International and other relevant websites and repositories were also searched in March-April 2014 for documents dated between 1992 and 2012. All citations were imported into a bibliographic database. Published and unpublished tools and resources were included in the review if they were in English, related to primary care quality improvement and addressed any of the seven PC-PIT elements of a high-performing practice. Tools and resources that met the eligibility criteria were then evaluated for their accessibility, relevance, utility and comprehensiveness using a four-criteria appraisal framework. We used a data extraction template to systematically extract information from eligible tools and resources. A content analysis approach was used to explore the tools and resources and collate relevant information: name of the tool or resource, year and country of development, author, name of the organisation that provided access and its URL, accessibility information or problems, overview of each tool or resource and the quality improvement element(s) it addresses. If available, a copy of the tool or resource was downloaded into the bibliographic database, along with supporting evidence (published or unpublished) on its use in primary care. This systematic review identified 53 tools and resources that can potentially be provided as part of a suite of tools and resources to support primary care practices in

Quality Appraisal of Single-Subject Experimental Designs: An Overview and Comparison of Different Appraisal Tools

Science.gov (United States)

Wendt, Oliver; Miller, Bridget

2012-01-01

Critical appraisal of the research literature is an essential step in informing and implementing evidence-based practice. Quality appraisal tools that assess the methodological quality of experimental studies provide a means to identify the most rigorous research suitable for evidence-based decision-making. In single-subject experimental research,…

Primary care physicians’ perspectives on computer-based health risk assessment tools for chronic diseases: a mixed methods study

Directory of Open Access Journals (Sweden)

Teja Voruganti

2015-09-01

Full Text Available Background Health risk assessment tools compute an individual’s risk of developing a disease. Routine use of such tools by primary care physicians (PCPs is potentially useful in chronic disease prevention. We sought physicians’ awareness and perceptions of the usefulness, usability and feasibility of performing assessments with computer-based risk assessment tools in primary care settings.Methods Focus groups and usability testing with a computer-based risk assessment tool were conducted with PCPs from both university-affiliated and community-based practices. Analysis was derived from grounded theory methodology.Results PCPs (n = 30 were aware of several risk assessment tools although only select tools were used routinely. The decision to use a tool depended on how use impacted practice workflow and whether the tool had credibility. Participants felt that embedding tools in the electronic medical records (EMRs system might allow for health information from the medical record to auto-populate into the tool. User comprehension of risk could also be improved with computer-based interfaces that present risk in different formats.Conclusions In this study, PCPs chose to use certain tools more regularly because of usability and credibility. Despite there being differences in the particular tools a clinical practice used, there was general appreciation for the usefulness of tools for different clinical situations. Participants characterised particular features of an ideal tool, feeling strongly that embedding risk assessment tools in the EMR would maximise accessibility and use of the tool for chronic disease management. However, appropriate practice workflow integration and features that facilitate patient understanding at point-of-care are also essential. 

A knowledge translation tool improved osteoporosis disease management in primary care: an interrupted time series analysis.

Science.gov (United States)

Kastner, Monika; Sawka, Anna M; Hamid, Jemila; Chen, Maggie; Thorpe, Kevin; Chignell, Mark; Ewusie, Joycelyne; Marquez, Christine; Newton, David; Straus, Sharon E

2014-09-25

Osteoporosis affects over 200 million people worldwide at a high cost to healthcare systems, yet gaps in management still exist. In response, we developed a multi-component osteoporosis knowledge translation (Op-KT) tool involving a patient-initiated risk assessment questionnaire (RAQ), which generates individualized best practice recommendations for physicians and customized education for patients at the point of care. The objective of this study was to evaluate the effectiveness of the Op-KT tool for appropriate disease management by physicians. The Op-KT tool was evaluated using an interrupted time series design. This involved multiple assessments of the outcomes 12 months before (baseline) and 12 months after tool implementation (52 data points in total). Inclusion criteria were family physicians and their patients at risk for osteoporosis (women aged ≥ 50 years, men aged ≥ 65 years). Primary outcomes were the initiation of appropriate osteoporosis screening and treatment. Analyses included segmented linear regression modeling and analysis of variance. The Op-KT tool was implemented in three family practices in Ontario, Canada representing 5 family physicians with 2840 age eligible patients (mean age 67 years; 76% women). Time series regression models showed an overall increase from baseline in the initiation of screening (3.4%; P management addressed by their physician. Study limitations included the inherent susceptibility of our design compared with a randomized trial. The multicomponent Op-KT tool significantly increased osteoporosis investigations in three family practices, and highlights its potential to facilitate patient self-management. Next steps include wider implementation and evaluation of the tool in primary care.

Monte Carlo simulation - a powerful tool to support experimental activities in structure reliability

International Nuclear Information System (INIS)

Yuritzinn, T.; Chapuliot, S.; Eid, M.; Masson, R.; Dahl, A.; Moinereau, D.

2003-01-01

Monte-Carlo Simulation (MCS) can have different uses in supporting structure reliability investigations and assessments. In this paper we focus our interest on the use of MCS as a numerical tool to support the fitting of the experimental data related to toughness experiments. (authors)

Developing a Multi-Dimensional Early Elementary Mathematics Screener and Diagnostic Tool: The Primary Mathematics Assessment.

Science.gov (United States)

Brendefur, Jonathan L; Johnson, Evelyn S; Thiede, Keith W; Strother, Sam; Severson, Herb H

2018-01-01

There is a critical need to identify primary level students experiencing difficulties in mathematics to provide immediate and targeted instruction that remediates their deficits. However, most early math screening instruments focus only on the concept of number, resulting in inadequate and incomplete information for teachers to design intervention efforts. We propose a mathematics assessment that screens and provides diagnostic information in six domains that are important to building a strong foundation in mathematics. This article describes the conceptual framework and psychometric qualities of a web-based assessment tool, the Primary Math Assessment (PMA). The PMA includes a screener to identify students at risk for poor math outcomes and a diagnostic tool to provide a more in-depth profile of children's specific strengths and weaknesses in mathematics. The PMA allows teachers and school personnel to make better instructional decisions by providing more targeted analyses.

Experimental Activities in Primary School to Learn about Microbes in an Oral Health Education Context

Science.gov (United States)

Mafra, Paulo; Lima, Nelson; Carvalho, Graça S.

2015-01-01

Experimental science activities in primary school enable important cross-curricular learning. In this study, experimental activities on microbiology were carried out by 16 pupils in a Portuguese grade-4 classroom (9-10?years old) and were focused on two problem-questions related to microbiology and health: (1) do your teeth carry microbes? (2) why…

MYRRHA/XT-ADS primary system design and experimental devices

International Nuclear Information System (INIS)

Maes, D.

2009-01-01

The EUROTRANS project is an integrated project in the Sixth European Framework Program in the context of Partitioning and Transmutation. The objective of this project is to work towards an ETD (European Transmutation Demonstration) in a step-wise manner. The first step is to carry out an advanced design of a small-scale XT-ADS (eXperimental Transmutation in an Accelerator Driven System) for realisation in a short-term (about 10 years) as well as to accomplish a generic conceptual design of EFIT (European Facility for Industrial Transmutation) for realisation in the long-term. The MYRRHA-2005 design served as a starting basis for the XT-ADS. Many options have been revisited and the framework is now set up. While the MYRRHA-2005 design was still a conceptual design, the intention is to get at the end of the EUROTRANS project (March 2009) an advanced design of the XT-ADS, albeit a first advanced design. While the design work performed during the first years of the project (2005-2006) was mainly devoted to optimise and enhance the primary and secondary system configuration according to the suggestions and contributions of our industrial partners (Ansaldo Nucleare, Areva, Suez-Tractebel) within the DM1 (Domain 1 D ESIGN ) , the last year work objectives mainly consisted of (1) the release of the Remote Handling Design Catalogue for XT-ADS and (2) the formulation of the specification of the experimental devices according to the XT-ADS objectives and adapted to the actual XT-ADS core and core support structure design; (3) the detailed calculations of the main XT-ADS primary and secondary system components

Seeking high reliability in primary care: Leadership, tools, and organization.

Science.gov (United States)

Weaver, Robert R

2015-01-01

Leaders in health care increasingly recognize that improving health care quality and safety requires developing an organizational culture that fosters high reliability and continuous process improvement. For various reasons, a reliability-seeking culture is lacking in most health care settings. Developing a reliability-seeking culture requires leaders' sustained commitment to reliability principles using key mechanisms to embed those principles widely in the organization. The aim of this study was to examine how key mechanisms used by a primary care practice (PCP) might foster a reliability-seeking, system-oriented organizational culture. A case study approach was used to investigate the PCP's reliability culture. The study examined four cultural artifacts used to embed reliability-seeking principles across the organization: leadership statements, decision support tools, and two organizational processes. To decipher their effects on reliability, the study relied on observations of work patterns and the tools' use, interactions during morning huddles and process improvement meetings, interviews with clinical and office staff, and a "collective mindfulness" questionnaire. The five reliability principles framed the data analysis. Leadership statements articulated principles that oriented the PCP toward a reliability-seeking culture of care. Reliability principles became embedded in the everyday discourse and actions through the use of "problem knowledge coupler" decision support tools and daily "huddles." Practitioners and staff were encouraged to report unexpected events or close calls that arose and which often initiated a formal "process change" used to adjust routines and prevent adverse events from recurring. Activities that foster reliable patient care became part of the taken-for-granted routine at the PCP. The analysis illustrates the role leadership, tools, and organizational processes play in developing and embedding a reliable-seeking culture across an

Experimental investigation of processes in primary circuit relief system

International Nuclear Information System (INIS)

Tomas, Z.; Simo, T.; Konecny, A.

1989-01-01

The protective condenser (direct contact condenser) is one of the basic components of the primary circuit relief system of WWER power plants. The steam flowing from the surge tank through relief valves into the subcooled water condensates in the protective condenser vessel. Two simple physical models were designed and constructed for investigation of bubbling through (contact condensation). An experimental program was performed with the aim of determining the distribution of temperatures in the axis of the steam jet and its vicinity, determining the velocity field of water into vicinity of steam jets, observing the geometrical shape of jets and their interaction and determining important values for mathematical model. (orig.)

Experimental studies of PWR primary piping under loca

International Nuclear Information System (INIS)

Caumette, Pierre; Garcia, J.L.

1980-07-01

The experimental program performed on AQUITAINE II facility is directed to study the mechanical behavior of primary PWR pipes and the forces exerted on the neighbouring structures as a consequence of a breach opening. It has been developed in the form of a quadripartite agreement between the Commissariat a l'Energie Atomique, Framatome, Electricite de France and Westinghouse. Some forty tests have been carried out with different pipe configurations (straight tube, elbow, S- or U-shaped tube) and different break types (single or double guillotine). The following aspects are investigated: - the dynamic behavior of the pipe and in particular the formation of a plastic hinge at the restraint; - the impact function of a pipe or an energy-absorbing bumper; - the lateral stability of both ends of a pipe, after a double-guillotine break [fr

Leveraging quality improvement through use of the Systems Assessment Tool in Indigenous primary health care services: a mixed methods study.

Science.gov (United States)

Cunningham, Frances C; Ferguson-Hill, Sue; Matthews, Veronica; Bailie, Ross

2016-10-18

Assessment of the quality of primary health care health delivery systems is a vital part of continuous quality improvement (CQI) processes. The Systems Assessment Tool (SAT) was designed to support Indigenous PHC services in assessing and improving their health care systems. It was based on the Assessment of Chronic Illness Care scale, and on practical experience with applying systems assessments in quality improvement in Indigenous primary health care. We describe the development and application of the SAT, report on a survey to assess the utility of the SAT and review the use of the SAT in other CQI research programs. The mixed methods approach involved a review of documents and internal reports relating to experience with use of the SAT since its development in 2002 and a survey of key informants on their experience with using the SAT. The paper drew from documents and internal reports to describe the SAT development and application in primary health care services from 2002 to 2014. Survey feedback highlighted the benefit to the whole primary health care team from participating in the SAT, bringing to light issues that might not emerge with separate individual tool completion. A majority of respondents reported changes in their health centres as a result of using the SAT. Good organisational and management support assisted with ensuring allocation of time and resources for SAT conduct. Respondents identified the importance of having a skilled, external facilitator. Originally designed as a measurement tool, the SAT rapidly evolved to become an important development tool, assisting teams in learning about primary health care system functioning, applying best practice and contributing to team strengthening. It is valued by primary health care centres as a lever in implementing improvements to strengthen centre delivery systems, and has potential for further adaptation and wider application in Australia and internationally.

Solid waste management in primary healthcare centers: application of a facilitation tool

Directory of Open Access Journals (Sweden)

Ana Maria Maniero Moreira

Full Text Available Abstract Objectives: to propose a tool to facilitate diagnosis, formulation and evaluation of the Waste Management Plan in Primary Healthcare Centers and to present the results of the application in four selected units. Method: descriptive research, covering the stages of formulation /application of the proposed instrument and the evaluation of waste management performance at the units. Results: the tool consists in five forms; specific indicators of waste generation for outpatients healthcare units were proposed, and performance indicators that give scores for compliance with current legislation. In the studied units it is generated common waste (52-60%, infectious-sharps (31-42% and recyclable (5-17%. The average rates of generation are: 0,09kg of total waste/outpatient assistance and 0,09kg of infectious-sharps waste/outpatient procedure. The compliance with regulations, initially 26-30%, then reached 30-38% a year later. Conclusion: the tool showed to be easy to use, bypassing the existence of a complex range of existing regulatory requirements, allowed to identify non-conformities, pointed out corrective measures and evaluated the performance of waste management. In this sense, it contributes to decision making and management practices relating to waste, tasks usually assigned to nurses. It is recommended that the tool be applied in similar healthcare units for comparative studies, and implementation of necessary adaptations for other medical services.

Towards good dementia care: Awareness and uptake of an online Dementia Pathways tool for rural and regional primary health practitioners.

Science.gov (United States)

Ollerenshaw, Alison; Wong Shee, Anna; Yates, Mark

2018-04-01

To explore the awareness and usage of an online dementia pathways tool (including decision tree and region-specific dementia services) for primary health practitioners (GPs and nurses) in regional Victoria. Quantitative pilot study using surveys and Google Analytics. A large regional area (48 000 square kilometres, population 220 000) in Victoria. Two hundred and sixty-three GPs and 160 practice nurses were invited to participate, with 42 respondents (GPs, n = 21; practice nurses, n = 21). Primary care practitioners' awareness and usage of the dementia pathways tool. Survey respondents that had used the tool (n = 14) reported accessing information about diagnosis, management and referral. Practitioners reported improvements in knowledge, skills and confidence about core dementia topics. There were 9683 page views between August 2013 and February 2015 (monthly average: 509 page views). The average time spent on page was 2.03 min, with many visitors (68%) spending more than 4 min at the site. This research demonstrates that the tool has been well received by practitioners and has been consistently used since its launch. Health practitioners' valued the content and the availability of local resources. Primary health practitioners reported that the dementia pathways tool provided access to region-specific referral and management resources for all stages of dementia. Such tools have broad transferability in other health areas with further research needed to determine their contribution to learning in the practice setting and over time. © 2017 National Rural Health Alliance Inc.

Longitudinal adoption rates of complex decision support tools in primary care.

Science.gov (United States)

McCullagh, Lauren; Mann, Devin; Rosen, Lisa; Kannry, Joseph; McGinn, Thomas

2014-12-01

Translating research findings into practice promises to standardise care. Translation includes the integration of evidence-based guidelines at the point of care, discerning the best methods to disseminate research findings and models to sustain the implementation of best practices.By applying usability testing to clinical decision support(CDS) design, overall adoption rates of 60% can be realised.What has not been examined is how long adoption rates are sustained and the characteristics associated with long-term use. We conducted secondary analysis to decipher the factors impacting sustained use of CD Stools. This study was a secondary data analysis from a clinical trial conducted at an academic institution in New York City. Study data was identified patients electronic health records (EHR). The trial was to test the implementation of an integrated clinical prediction rule(iCPR) into the EHR. The primary outcome variable was iCPR tool acceptance of the tool. iCPR tool completion and iCPR smartest completion were additional outcome variables of interest. The secondary aim was to examine user characteristics associated with iCPR tool use in later time periods. Characteristics of interest included age, resident year, use of electronic health records (yes/no) and use of best practice alerts (BPA) (yes/no). Generalised linear mixed models (GLiMM) were used to compare iCPR use over time for each outcome of interest: namely, iCPR acceptance, iCPR completion and iCPR smartset completion.GLiMM was also used to examine resident characteristics associated with iCPR tool use in later time periods; specifically, intermediate and long-term (ie, 90+days). The tool was accepted, on average, 82.18% in the first 90 days (short-term period). The use decreases to 56.07% and 45.61% in intermediate and long-term time periods, respectively. There was a significant association between iCPR tool completion and time periods(pknowledge of the clinical prediction rule, or gained clinical

Primary peak and chronic malaria infection levels are correlated in experimentally infected great reed warblers.

Science.gov (United States)

Asghar, Muhammad; Westerdahl, Helena; Zehtindjiev, Pavel; Ilieva, Mihaela; Hasselquist, Dennis; Bensch, Staffan

2012-09-01

Malaria parasites often manage to maintain an infection for several months or years in their vertebrate hosts. In humans, rodents and birds, most of the fitness costs associated with malaria infections are in the short initial primary (high parasitaemia) phase of the infection, whereas the chronic phase (low parasitaemia) is more benign to the host. In wild birds, malaria parasites have mainly been studied during the chronic phase of the infection. This is because the initial primary phase of infection is short in duration and infected birds with severe disease symptoms tend to hide in sheltered places and are thus rarely caught and sampled. We therefore wanted to investigate the relationship between the parasitaemia during the primary and chronic phases of the infection using an experimental infection approach. We found a significant positive correlation between parasitaemia in the primary peak and the subsequent chronic phase of infection when we experimentally infected great reed warblers (Acrocephalus arundinaceus) with Plasmodium ashfordi. The reason for this association remains to be understood, but might arise from individual variation in exoerythrocytic parasite reservoirs in hosts, parasite antigenic diversity and/or host genetics. Our results suggest that the chronic phase parasitaemia can be used to qualitatively infer the parasitaemia of the preceding and more severe primary phase, which is a very important finding for studies of avian malaria in wild populations.

Use of communication tool within electronic medical record to improve primary nonadherence.

Science.gov (United States)

Kerner, Daniel E; Knezevich, Emily L

The primary objective of this study was to determine if an online reminder decreased the rate of primary nonadherence for antihypertensive medications in patients seen in 2 primary care clinics in Omaha, NE. The secondary objectives were to determine if patients receiving the intervention achieved lower blood pressure values at follow-up visits and to determine if the intervention decreased the number of days between prescribing and prescription pick-up. A report was generated in an electronic health record to identify patients prescribed a new antihypertensive medication from a physician at one of the primary care clinics. Patients that failed to pick up this new prescription from the pharmacy within 7 days were sent an electronic reminder via an online patient portal. A baseline comparator group was created with the use of retrospective chart reviews for the 6 months before prospective data collection. Primary nonadherence rate and blood pressure values at follow-up visits were compared between the prospective and baseline comparator groups. The primary nonadherence rate decreased from 65.5% to 22.2% when comparing the baseline and prospective groups, respectively. The mean days to prescription pick-up decreased from 24.5 to 12.56 in the baseline and prospective groups. The prospective group showed a larger decrease in systolic blood pressure (17.33 mm Hg vs. 0.75 mm Hg) and diastolic blood pressure (6.56 mm Hg vs. 2.25 mm Hg) compared with the baseline group. An online reminder through the electronic medical record appears to improve patient primary nonadherence, number of days between prescribing and prescription pick-up, and blood pressure measurements at follow-up visits. This research shows that an online reminder may be a valuable tool to improve patient primary adherence and health outcomes. Further research is needed with the use of a larger sample population to support any hypotheses about the effectiveness of the intervention. Copyright © 2017 American

Experimental simulation of low rate primary coolant leaks. For the case of vessel head penetrations affected by through wall cracking

International Nuclear Information System (INIS)

You, D.; Feron, D.; Turluer, G.

2002-01-01

An experimental simulation of primary coolant leaks was carried out to determine how the composition of the leaking liquid would change. The experiment used the EVA experimental setup, specially designed for quantitatively investigating concentration phenomena driven by evaporation. The test showed that the final composition, obtained from a solution representative of the primary coolant at the beginning of the cycle, is highly concentrated and slightly acid. The experimental results are compared with those obtained using the MULTEQ software. (authors)

Experimental investigation into effect of cutting parameters on surface integrity of hardened tool steel

Science.gov (United States)

Bashir, K.; Alkali, A. U.; Elmunafi, M. H. S.; Yusof, N. M.

2018-04-01

Recent trend in turning hardened materials have gained popularity because of its immense machinability benefits. However, several machining processes like thermal assisted machining and cryogenic machining have reveal superior machinability benefits over conventional dry turning of hardened materials. Various engineering materials have been studied. However, investigations on AISI O1 tool steel have not been widely reported. In this paper, surface finish and surface integrity dominant when hard turning AISI O1 tool steel is analysed. The study is focused on the performance of wiper coated ceramic tool with respect to surface roughness and surface integrity of hardened tool steel. Hard turned tool steel was machined at varying cutting speed of 100, 155 and 210 m/min and feed rate of 0.05, 0.125 and 0.20mm/rev. The depth of cut of 0.2mm was maintained constant throughout the machining trials. Machining was conducted using dry turning on 200E-axis CNC lathe. The experimental study revealed that the surface finish is relatively superior at higher cutting speed of 210m/min. The surface finish increases when cutting speed increases whereas surface finish is generally better at lower feed rate of 0.05mm/rev. The experimental study conducted have revealed that phenomena such as work piece vibration due to poor or improper mounting on the spindle also contributed to higher surface roughness value of 0.66Ra during turning at 0.2mm/rev. Traces of white layer was observed when viewed with optical microscope which shows evidence of cutting effects on the turned work material at feed rate of 0.2 rev/min

Improving Awareness of Health Hazards Associated with Air Pollution in Primary School Children: Design and Test of Didactic Tools

Science.gov (United States)

Carducci, Annalaura; Casini, Beatrice; Donzelli, Gabriele; Verani, Marco; Bruni, Beatrice; Ceretti, Elisabetta; Zani, Claudia; Carraro, Elisabetta; Bonetta, Sara; Bagordo, Francesco; Grassi, Tiziana; Villarini, Milena; Bonizzoni, Silvia; Zagni, Licia; Gelatti, Umberto

2016-01-01

One of the objectives of the MAPEC-Life project is raising children's awareness on air quality and its health effects. To achieve this goal, we designed didactic tools for primary school students, including leaflets with more information for teachers, a cartoon, and three educational videogames. The tools were then tested with 266 children who…

Experimental evaluation of radiator control based on primary supply temperature for district heating substations

International Nuclear Information System (INIS)

Gustafsson, Jonas; Delsing, Jerker; Deventer, Jan van

2011-01-01

Highlights: → We compared a new radiator system control approach with traditional control. → This is an experimental verification of previous simulation results. → We examine changes in delta-T and indoor comfort. → The indoor comfort were not affected by the introduction of alt. radiator control. → The alternative control method can contribute to an increased delta-T. -- Abstract: In this paper, we evaluate whether the primary supply temperature in district heating networks can be used to control radiator systems in buildings connected to district heating; with the purpose of increasing the ΔT. The primary supply temperature in district heating systems can mostly be described as a function of outdoor temperature; similarly, the radiator supply temperature in houses, offices and industries can also be described as a function of outdoor temperature. To calibrate the radiator control system to produce an ideally optimal radiator supply temperature that produces a maximized ΔT across the substation, the relationship between the primary supply temperature and outdoor temperature must be known. However, even if the relation is known there is always a deviation between the expected primary supply temperature and the actual temperature of the received distribution media. This deviation makes the radiator control system incapable of controlling the radiator supply temperature to a point that would generate a maximized ΔT. Published simulation results show that it is possible and advantageous to utilize the primary supply temperature for radiator system control. In this paper, the simulation results are experimentally verified through implementation of the control method in a real district heating substation. The primary supply temperature is measured by the heat-meter and is shared with the radiator control system; thus no additional temperature sensors were needed to perform the experiments. However additional meters were installed for surveillance purposes

The Influence of an Internet-Based Formative Assessment Tool on Primary Grades Students' Number Sense Achievement

Science.gov (United States)

Polly, Drew; Wang, Chuang; Martin, Christie; Lambert, Richard G.; Pugalee, David K.; Middleton, Catharina Win

2017-01-01

This study examined primary grades students' achievement on number sense tasks administered through an Internet-based formative assessment tool, Assessing Math Concepts Anywhere. Data were analyzed from 2,357 students in teachers' classrooms who had participated in a year-long professional development program on mathematics formative assessment,…

The preliminary development and testing of a global trigger tool to detect error and patient harm in primary-care records.

Science.gov (United States)

de Wet, C; Bowie, P

2009-04-01

A multi-method strategy has been proposed to understand and improve the safety of primary care. The trigger tool is a relatively new method that has shown promise in American and secondary healthcare settings. It involves the focused review of a random sample of patient records using a series of "triggers" that alert reviewers to potential errors and previously undetected adverse events. To develop and test a global trigger tool to detect errors and adverse events in primary-care records. Trigger tool development was informed by previous research and content validated by expert opinion. The tool was applied by trained reviewers who worked in pairs to conduct focused audits of 100 randomly selected electronic patient records in each of five urban general practices in central Scotland. Review of 500 records revealed 2251 consultations and 730 triggers. An adverse event was found in 47 records (9.4%), indicating that harm occurred at a rate of one event per 48 consultations. Of these, 27 were judged to be preventable (42%). A further 17 records (3.4%) contained evidence of a potential adverse event. Harm severity was low to moderate for most patients (82.9%). Error and harm rates were higher in those aged > or =60 years, and most were medication-related (59%). The trigger tool was successful in identifying undetected patient harm in primary-care records and may be the most reliable method for achieving this. However, the feasibility of its routine application is open to question. The tool may have greater utility as a research rather than an audit technique. Further testing in larger, representative study samples is required.

Classical Experiments Revisited: Smartphones and Tablet PCs as Experimental Tools in Acoustics and Optics

Science.gov (United States)

Klein, P.; Hirth, M.; Gröber, S.; Kuhn, J.; Müller, A.

2014-01-01

Smartphones and tablets are used as experimental tools and for quantitative measurements in two traditional laboratory experiments for undergraduate physics courses. The Doppler effect is analyzed and the speed of sound is determined with an accuracy of about 5% using ultrasonic frequency and two smartphones, which serve as rotating sound emitter…

Solid waste management in primary healthcare centers: application of a facilitation tool 1

Science.gov (United States)

Moreira, Ana Maria Maniero; Günther, Wanda Maria Risso

2016-01-01

Abstract Objectives: to propose a tool to facilitate diagnosis, formulation and evaluation of the Waste Management Plan in Primary Healthcare Centers and to present the results of the application in four selected units. Method: descriptive research, covering the stages of formulation /application of the proposed instrument and the evaluation of waste management performance at the units. Results: the tool consists in five forms; specific indicators of waste generation for outpatients healthcare units were proposed, and performance indicators that give scores for compliance with current legislation. In the studied units it is generated common waste (52-60%), infectious-sharps (31-42%) and recyclable (5-17%). The average rates of generation are: 0,09kg of total waste/outpatient assistance and 0,09kg of infectious-sharps waste/outpatient procedure. The compliance with regulations, initially 26-30%, then reached 30-38% a year later. Conclusion: the tool showed to be easy to use, bypassing the existence of a complex range of existing regulatory requirements, allowed to identify non-conformities, pointed out corrective measures and evaluated the performance of waste management. In this sense, it contributes to decision making and management practices relating to waste, tasks usually assigned to nurses. It is recommended that the tool be applied in similar healthcare units for comparative studies, and implementation of necessary adaptations for other medical services. PMID:27556874

The human papillomavirus vaccine: A powerful tool for the primary prevention of cervical cancer.

OpenAIRE

Nubia Muñoz; Julio César Reina; Gloria Inés Sánchez

2009-01-01

Prophylactic human papillomavirus (HPV) vaccine is the most promissory public health tool for primary prevention of cervical cancer. Immunization of females before the acquisition of HPV infection has the greatest impact in preventing pre-neoplasic lesions and cervical cancer. Current HPV vaccines do not eliminate cervical cancer risk, therefore, screening should continue covering vaccinated as well as women that do not get the vaccine. The strategies that include combination of high-coverage...

Physics validation of detector simulation tools for LHC

International Nuclear Information System (INIS)

Beringer, J.

2004-01-01

Extensive studies aimed at validating the physics processes built into the detector simulation tools Geant4 and Fluka are in progress within all Large Hardon Collider (LHC) experiments, within the collaborations developing these tools, and within the LHC Computing Grid (LCG) Simulation Physics Validation Project, which has become the primary forum for these activities. This work includes detailed comparisons with test beam data, as well as benchmark studies of simple geometries and materials with single incident particles of various energies for which experimental data is available. We give an overview of these validation activities with emphasis on the latest results

Use of a screening tool and primary health care gerontology nurse specialist for high-needs older people.

Science.gov (United States)

King, Anna; Boyd, Michal; Dagley, Lynelle

2017-02-01

To describe implementation of an innovative gerontology nurse specialist role within one primary health organisation in Auckland, New Zealand. Quantitative outcomes of the screening tool as well as the nurse specialist assessment will be presented. The intervention involved use of the Brief Risk Identification for Geriatric Health Tool (BRIGHT) to identify high-needs older people with subsequent comprehensive geriatric assessment (CGA) performed by the gerontology nurse specialist. A total 384 of the 416 BRIGHTs were completed (92% response rate) and 15% of these were identified as high risk (n = 57). The BRIGHTs for high-risk older people revealed the highest scoring question was 'needing help with housework' (26%). The most frequent intervention by the gerontology nurse specialist was education (30%). The primary health care gerontology nurse specialist model delivers a proactive case finding and specialist gerontology intervention for older people at high risk of functional or health decline.

The ligase chain reaction as a primary screening tool for the detection of culture positive tuberculosis.

LENUS (Irish Health Repository)

O'Connor, T M

2012-02-03

BACKGROUND: The ligase chain reaction Mycobacterium tuberculosis assay uses ligase chain reaction technology to detect tuberculous DNA sequences in clinical specimens. A study was undertaken to determine its sensitivity and specificity as a primary screening tool for the detection of culture positive tuberculosis. METHODS: The study was conducted on 2420 clinical specimens (sputum, bronchoalveolar lavage fluid, pleural fluid, urine) submitted for primary screening for Mycobacterium tuberculosis to a regional medical microbiology laboratory. Specimens were tested in parallel with smear, ligase chain reaction, and culture. RESULTS: Thirty nine patients had specimens testing positive by the ligase chain reaction assay. Thirty two patients had newly diagnosed tuberculosis, one had a tuberculosis relapse, three had tuberculosis (on antituberculous therapy when tested), and three had healed tuberculosis. In the newly diagnosed group specimens were smear positive in 21 cases (66%), ligase chain reaction positive in 30 cases (94%), and culture positive in 32 cases (100%). Using a positive culture to diagnose active tuberculosis, the ligase chain reaction assay had a sensitivity of 93.9%, a specificity of 99.8%, a positive predictive value of 83.8%, and a negative predictive value of 99.9%. CONCLUSIONS: This study is the largest clinical trial to date to report the efficacy of the ligase chain reaction as a primary screening tool to detect Mycobacterium tuberculosis infection. The authors conclude that ligase chain reaction is a useful primary screening test for tuberculosis, offering speed and discrimination in the early stages of diagnosis and complementing traditional smear and culture techniques.

Ratcheting problems for ITER [International Thermonuclear Experimental Reactor

International Nuclear Information System (INIS)

Majumdar, S.

1991-01-01

Because of the presence of high cyclic thermal stress, pressure-induced primary stress, and disruption-induced high cyclic primary stress, ratcheting of the first wall poses a serious challenge to the designers of ITER (International Thermonuclear Experimental Reactor). Existing design tools such as the Bree diagram in the ASME Boiler and Pressure Vessels Code, are not directly applicable to ITER, because of important differences in geometry and loading modes. Available alternative models for ratcheting are discussed and new Bree diagrams, that are more relevant for fusion reactor applications, are proposed. 9 refs., 17 figs

Tools for Genetic Studies in Experimental Populations of Polyploids

Directory of Open Access Journals (Sweden)

Peter M. Bourke

2018-04-01

Full Text Available Polyploid organisms carry more than two copies of each chromosome, a condition rarely tolerated in animals but which occurs relatively frequently in the plant kingdom. One of the principal challenges faced by polyploid organisms is to evolve stable meiotic mechanisms to faithfully transmit genetic information to the next generation upon which the study of inheritance is based. In this review we look at the tools available to the research community to better understand polyploid inheritance, many of which have only recently been developed. Most of these tools are intended for experimental populations (rather than natural populations, facilitating genomics-assisted crop improvement and plant breeding. This is hardly surprising given that a large proportion of domesticated plant species are polyploid. We focus on three main areas: (1 polyploid genotyping; (2 genetic and physical mapping; and (3 quantitative trait analysis and genomic selection. We also briefly review some miscellaneous topics such as the mode of inheritance and the availability of polyploid simulation software. The current polyploid analytic toolbox includes software for assigning marker genotypes (and in particular, estimating the dosage of marker alleles in the heterozygous condition, establishing chromosome-scale linkage phase among marker alleles, constructing (short-range haplotypes, generating linkage maps, performing genome-wide association studies (GWAS and quantitative trait locus (QTL analyses, and simulating polyploid populations. These tools can also help elucidate the mode of inheritance (disomic, polysomic or a mixture of both as in segmental allopolyploids or reveal whether double reduction and multivalent chromosomal pairing occur. An increasing number of polyploids (or associated diploids are being sequenced, leading to publicly available reference genome assemblies. Much work remains in order to keep pace with developments in genomic technologies. However, such

Tools for Genetic Studies in Experimental Populations of Polyploids.

Science.gov (United States)

Bourke, Peter M; Voorrips, Roeland E; Visser, Richard G F; Maliepaard, Chris

2018-01-01

Polyploid organisms carry more than two copies of each chromosome, a condition rarely tolerated in animals but which occurs relatively frequently in the plant kingdom. One of the principal challenges faced by polyploid organisms is to evolve stable meiotic mechanisms to faithfully transmit genetic information to the next generation upon which the study of inheritance is based. In this review we look at the tools available to the research community to better understand polyploid inheritance, many of which have only recently been developed. Most of these tools are intended for experimental populations (rather than natural populations), facilitating genomics-assisted crop improvement and plant breeding. This is hardly surprising given that a large proportion of domesticated plant species are polyploid. We focus on three main areas: (1) polyploid genotyping; (2) genetic and physical mapping; and (3) quantitative trait analysis and genomic selection. We also briefly review some miscellaneous topics such as the mode of inheritance and the availability of polyploid simulation software. The current polyploid analytic toolbox includes software for assigning marker genotypes (and in particular, estimating the dosage of marker alleles in the heterozygous condition), establishing chromosome-scale linkage phase among marker alleles, constructing (short-range) haplotypes, generating linkage maps, performing genome-wide association studies (GWAS) and quantitative trait locus (QTL) analyses, and simulating polyploid populations. These tools can also help elucidate the mode of inheritance (disomic, polysomic or a mixture of both as in segmental allopolyploids) or reveal whether double reduction and multivalent chromosomal pairing occur. An increasing number of polyploids (or associated diploids) are being sequenced, leading to publicly available reference genome assemblies. Much work remains in order to keep pace with developments in genomic technologies. However, such technologies

Validation of the TAPS-1: A Four-Item Screening Tool to Identify Unhealthy Substance Use in Primary Care.

Science.gov (United States)

Gryczynski, Jan; McNeely, Jennifer; Wu, Li-Tzy; Subramaniam, Geetha A; Svikis, Dace S; Cathers, Lauretta A; Sharma, Gaurav; King, Jacqueline; Jelstrom, Eve; Nordeck, Courtney D; Sharma, Anjalee; Mitchell, Shannon G; O'Grady, Kevin E; Schwartz, Robert P

2017-09-01

The Tobacco, Alcohol, Prescription Medication, and Other Substance use (TAPS) tool is a combined two-part screening and brief assessment developed for adult primary care patients. The tool's first-stage screening component (TAPS-1) consists of four items asking about past 12-month use for four substance categories, with response options of never, less than monthly, monthly, weekly, and daily or almost daily. To validate the TAPS-1 in primary care patients. Participants completed the TAPS tool in self- and interviewer-administered formats, in random order. In this secondary analysis, the TAPS-1 was evaluated against DSM-5 substance use disorder (SUD) criteria to determine optimal cut-points for identifying unhealthy substance use at three severity levels (problem use, mild SUD, and moderate-to-severe SUD). Two thousand adult patients at five primary care sites. DSM-5 SUD criteria were determined via the modified Composite International Diagnostic Interview. Oral fluid was used as a biomarker of recent drug use. Optimal frequency-of-use cut-points on the self-administered TAPS-1 for identifying SUDs were ≥ monthly use for tobacco and alcohol (sensitivity = 0.92 and 0.71, specificity = 0.80 and 0.85, AUC = 0.86 and 0.78, respectively) and any reported use for illicit drugs and prescription medication misuse (sensitivity = 0.93 and 0.89, specificity = 0.85 and 0.91, AUC = 0.89 and 0.90, respectively). The performance of the interviewer-administered format was similar. When administered first, the self-administered format yielded higher disclosure rates for past 12-month alcohol use, illicit drug use, and prescription medication misuse. Frequency of use alone did not provide sufficient information to discriminate between gradations of substance use problem severity. Among those who denied drug use on the TAPS-1, less than 4% had a drug-positive biomarker. The TAPS-1 can identify unhealthy substance use in primary care patients with a high level of accuracy

The Strategy to Survive Primary Malaria Infection: An Experimental Study on Behavioural Changes in Parasitized Birds.

Directory of Open Access Journals (Sweden)

Andrey Mukhin

Full Text Available Avian malaria parasites (Haemosporida, Plasmodium are of cosmopolitan distribution, and they have a significant impact on vertebrate host fitness. Experimental studies show that high parasitemia often develops during primary malaria infections. However, field studies only occasionally reveal high parasitemia in free-living birds sampled using the traditional methods of mist-netting or trapping, and light chronic infections predominate. The reason for this discrepancy between field observation and experimental data remains insufficiently understood. Since mist-netting is a passive capture method, two main parameters determine its success in sampling infected birds in wildlife, i. e. the presence of parasitized birds at a study site and their mobility. In other words, the trapping probability depends on the survival rate of birds and their locomotor activity during infection. Here we test (1 the mortality rate of wild birds infected with Plasmodium relictum (the lineage pSGS1, (2 the changes in their behaviour during presence of an aerial predator, and (3 the changes in their locomotor activity at the stage of high primary parasitemia.We show that some behavioural features which might affect a bird's survival during a predator attack (time of reaction, speed of flush flight and take off angle did not change significantly during primary infection. However, the locomotor activity of infected birds was almost halved compared to control (non-infected birds during the peak of parasitemia. We report (1 the markedly reduced mobility and (2 the 20% mortality rate caused by P. relictum and conclude that these factors are responsible for the underrepresentation of birds in mist nets and traps during the stage of high primary parasitemia in wildlife. This study indicates that the widespread parasite, P. relictum (pSGS1 influences the behaviour of birds during primary parasitemia. Experimental studies combined with field observations are needed to better

The Strategy to Survive Primary Malaria Infection: An Experimental Study on Behavioural Changes in Parasitized Birds

Science.gov (United States)

Mukhin, Andrey; Palinauskas, Vaidas; Platonova, Elena; Kobylkov, Dmitry; Vakoliuk, Irina; Valkiūnas, Gediminas

2016-01-01

Avian malaria parasites (Haemosporida, Plasmodium) are of cosmopolitan distribution, and they have a significant impact on vertebrate host fitness. Experimental studies show that high parasitemia often develops during primary malaria infections. However, field studies only occasionally reveal high parasitemia in free-living birds sampled using the traditional methods of mist-netting or trapping, and light chronic infections predominate. The reason for this discrepancy between field observation and experimental data remains insufficiently understood. Since mist-netting is a passive capture method, two main parameters determine its success in sampling infected birds in wildlife, i. e. the presence of parasitized birds at a study site and their mobility. In other words, the trapping probability depends on the survival rate of birds and their locomotor activity during infection. Here we test (1) the mortality rate of wild birds infected with Plasmodium relictum (the lineage pSGS1), (2) the changes in their behaviour during presence of an aerial predator, and (3) the changes in their locomotor activity at the stage of high primary parasitemia.We show that some behavioural features which might affect a bird's survival during a predator attack (time of reaction, speed of flush flight and take off angle) did not change significantly during primary infection. However, the locomotor activity of infected birds was almost halved compared to control (non-infected) birds during the peak of parasitemia. We report (1) the markedly reduced mobility and (2) the 20% mortality rate caused by P. relictum and conclude that these factors are responsible for the underrepresentation of birds in mist nets and traps during the stage of high primary parasitemia in wildlife. This study indicates that the widespread parasite, P. relictum (pSGS1) influences the behaviour of birds during primary parasitemia. Experimental studies combined with field observations are needed to better understand the

Does surface roughness influence the primary stability of acetabular cups? A numerical and experimental biomechanical evaluation.

Science.gov (United States)

Le Cann, Sophie; Galland, Alexandre; Rosa, Benoît; Le Corroller, Thomas; Pithioux, Martine; Argenson, Jean-Noël; Chabrand, Patrick; Parratte, Sébastien

2014-09-01

Most acetabular cups implanted today are press-fit impacted cementless. Anchorage begins with the primary stability given by insertion of a slightly oversized cup. This primary stability is key to obtaining bone ingrowth and secondary stability. We tested the hypothesis that primary stability of the cup is related to surface roughness of the implant, using both an experimental and a numerical models to analyze how three levels of surface roughness (micro, macro and combined) affect the primary stability of the cup. We also investigated the effect of differences in diameter between the cup and its substrate, and of insertion force, on the cups' primary stability. The results of our study show that primary stability depends on the surface roughness of the cup. The presence of macro-roughness on the peripheral ring is found to decrease primary stability; there was excessive abrasion of the substrate, damaging it and leading to poor primary stability. Numerical modeling indicates that oversizing the cup compared to its substrate has an impact on primary stability, as has insertion force. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Performance of the Tobacco, Alcohol, Prescription Medication, and Other Substance Use (TAPS) Tool for Substance Use Screening in Primary Care Patients.

Science.gov (United States)

McNeely, Jennifer; Wu, Li-Tzy; Subramaniam, Geetha; Sharma, Gaurav; Cathers, Lauretta A; Svikis, Dace; Sleiter, Luke; Russell, Linnea; Nordeck, Courtney; Sharma, Anjalee; O'Grady, Kevin E; Bouk, Leah B; Cushing, Carol; King, Jacqueline; Wahle, Aimee; Schwartz, Robert P

2016-11-15

Substance use, a leading cause of illness and death, is underidentified in medical practice. The Tobacco, Alcohol, Prescription medication, and other Substance use (TAPS) tool was developed to address the need for a brief screening and assessment instrument that includes all commonly used substances and fits into clinical workflows. The goal of this study was to assess the performance of the TAPS tool in primary care patients. Multisite study, conducted within the National Drug Abuse Treatment Clinical Trials Network, comparing the TAPS tool with a reference standard measure. (ClinicalTrials.gov: NCT02110693). 5 adult primary care clinics. 2000 adult patients consecutively recruited from clinic waiting areas. Interviewer- and self-administered versions of the TAPS tool were compared with a reference standard, the modified World Mental Health Composite International Diagnostic Interview (CIDI), which measures problem use and substance use disorder (SUD). Interviewer- and self-administered versions of the TAPS tool had similar diagnostic characteristics. For identifying problem use (at a cutoff of 1+), the TAPS tool had a sensitivity of 0.93 (95% CI, 0.90 to 0.95) and specificity of 0.87 (CI, 0.85 to 0.89) for tobacco and a sensitivity of 0.74 (CI, 0.70 to 0.78) and specificity of 0.79 (CI, 0.76 to 0.81) for alcohol. For problem use of illicit and prescription drugs, sensitivity ranged from 0.82 (CI, 0.76 to 0.87) for marijuana to 0.63 (CI, 0.47 to 0.78) for sedatives; specificity was 0.93 or higher. For identifying any SUD (at a cutoff of 2+), sensitivity was lower. The low prevalence of some drug classes led to poor precision in some estimates. Research assistants were not blinded to participants' TAPS tool responses when they administered the CIDI. In a diverse population of adult primary care patients, the TAPS tool detected clinically relevant problem substance use. Although it also may detect tobacco, alcohol, and marijuana use disorders, further refinement is

Primary experimental studies on mid-infrared FEL irradiation on dental substances at BFEL

CERN Document Server

Biao, Z J; Gao Xue Ju; He Wei; Huang Yu Ying; Li Yong Gui; LiuNianQing; Wang Min Kai; Wu Gan; Yan Xue Pin; Zhang Guo Qing

2001-01-01

A free electron laser (FEL) with its characteristics of wide wavelength tunability, ultrashort pulse time structure, and high peak power density is predominantly superior to all other conventional lasers in applications. Several experimental studies on mid-infrared FEL irradiation on dental enamel and dentine were performed at the Beijing FEL. Experimental aims were to investigate changes in the hardness, ratios of P to Ca and Cs before and after irradiation on samples with a characteristic absorption wavelength of 9.66 mu m, in the colors of these sample surfaces after irradiation with different wavelengths around the peak wavelength. The time dependence of temperature of the dentine sample was measured with its ps pulse effects compared to that with a continuous CO sub 2 laser. FTIR absorption spectra in the range of 2.5-15.4 mu m for samples of these hard dental substances and pure hydroxyapatite were first examined to decide their chemical components and absorption maximums. Primary experimental results w...

Organizing principles as tools for bridging the gap between system theory and biological experimentation.

Science.gov (United States)

Mekios, Constantinos

2016-04-01

Twentieth-century theoretical efforts towards the articulation of general system properties came short of having the significant impact on biological practice that their proponents envisioned. Although the latter did arrive at preliminary mathematical formulations of such properties, they had little success in showing how these could be productively incorporated into the research agenda of biologists. Consequently, the gap that kept system-theoretic principles cut-off from biological experimentation persisted. More recently, however, simple theoretical tools have proved readily applicable within the context of systems biology. In particular, examples reviewed in this paper suggest that rigorous mathematical expressions of design principles, imported primarily from engineering, could produce experimentally confirmable predictions of the regulatory properties of small biological networks. But this is not enough for contemporary systems biologists who adopt the holistic aspirations of early systemologists, seeking high-level organizing principles that could provide insights into problems of biological complexity at the whole-system level. While the presented evidence is not conclusive about whether this strategy could lead to the realization of the lofty goal of a comprehensive explanatory integration, it suggests that the ongoing quest for organizing principles is pragmatically advantageous for systems biologists. The formalisms postulated in the course of this process can serve as bridges between system-theoretic concepts and the results of molecular experimentation: they constitute theoretical tools for generalizing molecular data, thus producing increasingly accurate explanations of system-wide phenomena.

Use of electronic dietary assessment tools in primary care: an interdisciplinary perspective.

Science.gov (United States)

Bonilla, Carolina; Brauer, Paula; Royall, Dawna; Keller, Heather; Hanning, Rhona M; DiCenso, Alba

2015-02-25

Dietary assessment can be challenging for many reasons, including the wide variety of foods, eating patterns and nutrients to be considered. In team-based primary care practice, various disciplines may be involved in assessing diet. Electronic-based dietary assessment (e-DA) instruments available now through mobile apps or websites can potentially facilitate dietary assessment. Providers views of facilitators and barriers related to e-DA instruments and their recommendations for improvement can inform the further development of these tools. The objective of this study was to explore provider perspectives on e-DA tools in mobile apps and websites. The exploratory sequential mixed methods design included interdisciplinary focus groups followed by a web-based survey sent to Family Health Teams throughout Ontario, Canada. Descriptive and bivariate analyses were completed. Focus group transcripts contributed to web-survey content, while interpretive themes added depth and context. 11 focus groups with 50 providers revealed varying perspectives on the use of e-DA for: 1) improving patients' eating habits; 2) improving the quality of dietary assessment; and, 3) integrating e-DA into the care process. In the web-survey 191 respondents from nine disciplines in 73 FHTs completed the survey. Dietitians reported greater use of e-DA than other providers (63% vs.19%; p = .000) respectively. There was strong interest among disciplines in the use of e-DA tools for the management of obesity, diabetes and heart disease, especially for patient self-monitoring. Barriers identified were: patients' lack of comfort with using technology, misinterpretation of e-DA results by patients, time and education for providers to interpret results, and time for providers to offer counselling. e-DA tools in mobile apps and websites may improve dietary counselling over time. Addressing the identified facilitators and barriers can potentially promote the uptake of e-DA into clinical practice.

Cardiovascular autonomic dysfunction in primary ovarian insufficiency: clinical and experimental evidence

Science.gov (United States)

Goldmeier, Silvia; De Angelis, Kátia; Rabello Casali, Karina; Vilodre, César; Consolim-Colombo, Fernanda; Belló Klein, Adriane; Plentz, Rodrigo; Spritzer, PoliMara; Irigoyen, Maria-Cláudia

2014-01-01

Objective: Women with primary ovarian insufficiency (POI) present an increased risk for cardiovascular disease. In this study we tested the hypothesis that POI in women under hormone therapy (HT) are associated with vascular vasodilatation attenuation and cardiovascular autonomic dysfunction and these impairments are related to changes in systemic antioxidant enzymes. Furthermore, the possibility that ovarian hormone deprivation can induce such changes and that HT cannot reverse all of those impairments was examined in an experimental model of POI. Methods: Fifteen control and 17 patients with primary ovarian insufficiency receiving HT were included in the study. To test the systemic and cardiac consequences of ovarian hormone deprivation, ovariectomy was induced in young female rats that were submitted or not to HT. Spectral analysis of RR interval and blood pressure signals were performed and oxidative stress parameters were determined. Results: POI women under HT have increased mean arterial pressure (94±10 vs. 86±5 mmHg) despite normal endothelial and autonomic modulation of vasculature. Additionally, they presented impaired baroreflex sensitivity (3.9±1.38 vs. 7.15±3.62 ms/mmHg) and reduced heart rate variability (2310±1173 vs. 3754±1921 ms2). Similar results obtained in ovariectomized female rats were accompanied by an increased lipoperoxidation (7433±1010 vs. 6180±289 cps/mg protein) and decreased antioxidant enzymes in cardiac tissue. As it was observed in women, the HT in animals did not restore hemodynamic and autonomic dysfunctions. Conclusion: These data provide clinical and experimental evidence that long term HT may not restore all cardiovascular risk factors associated with ovarian hormone deprivation. PMID:24349626

The use of e-health and m-health tools in health promotion and primary prevention among older adults: a systematic literature review.

Science.gov (United States)

Kampmeijer, Ramon; Pavlova, Milena; Tambor, Marzena; Golinowska, Stanisława; Groot, Wim

2016-09-05

The use of e-health and m-health technologies in health promotion and primary prevention among older people is largely unexplored. This study provides a systematic review of the evidence on the scope of the use of e-health and m-health tools in health promotion and primary prevention among older adults (age 50+). A systematic literature review was conducted in October 2015. The search for relevant publications was done in the search engine PubMed. The key inclusion criteria were: e-health and m-health tools used, participants' age 50+ years, focus on health promotion and primary prevention, published in the past 10 years, in English, and full-paper can be obtained. The text of the publications was analyzed based on two themes: the characteristics of e-health and m-health tools and the determinants of the use of these tools by older adults. The quality of the studies reviewed was also assessed. The initial search resulted in 656 publications. After we applied the inclusion and exclusion criteria, 45 publications were selected for the review. In the publications reviewed, various types of e-health/m-health tools were described, namely apps, websites, devices, video consults and webinars. Most of the publications (60 %) reported studies in the US. In 37 % of the publications, the study population was older adults in general, while the rest of the publications studied a specific group of older adults (e.g. women or those with overweight). The publications indicated various facilitators and barriers. The most commonly mentioned facilitator was the support for the use of the e-health/m-health tools that the older adults received. E-health and m-health tools are used by older adults in diverse health promotion programs, but also outside formal programs to monitor and improve their health. The latter is hardly studied. The successful use of e-health/m-health tools in health promotion programs for older adults greatly depends on the older adults' motivation and support

Assessing readiness to work in primary health care: the content validity of a self-check tool for physiotherapists and other health professionals.

Science.gov (United States)

Stewart, Jenny; Haswell, Kate

2013-03-01

The New Zealand Primary Health Care Strategy has emphasised the importance of well-coordinated service teams in managing complex chronic conditions. There is international evidence that physiotherapists can contribute effectively to the prevention and management of these conditions. However, there are few examples of physiotherapists in New Zealand (NZ) engaging in primary health care (PHC). It has been recognised that professional development is necessary to optimise physiotherapists' participation in PHC. The aim of this study was to both design a self-check tool that physiotherapists could use as an initial step in preparing to work in PHC and to assess the content validity of the tool. A literature review informed the development of the self-check tool. The tool was reviewed by members of the Physiotherapy New Zealand PHC working party to establish content validity. The tool was found to have excellent content validity with an overall score of 0.937, exceeding the acceptable index of 0.8. Item validity was excellent or acceptable for all except two items, which were subsequently modified in the final tool. This investigation provides initial support for the tool's potential use by physiotherapists as a means of determining their readiness to work in PHC. It could have application beyond individual professional development to the wider context of team and organisational development. Additionally, with minor modifications the tool could have broader application to other professional groups.

The new STRESA tool for preservation of thermalhydraulic experimental data produced in the European Commission

International Nuclear Information System (INIS)

Pla, Patricia; Pascal, Ghislain; Tanarro, Jorge; Annunziato, Alessandro

2015-01-01

Highlights: • ITFs and severe accident data is of high importance to validate thermal hydraulic codes for NPPs. • LOBI, FARO, KROTOS and STORM produced a lot of TH and SA experimental data. • The JRC facilities data was stored in the JRC STRESA database developed by JRC. • The paper presents the new JRC STRESA database developed by JRC in 2014–2015. • The long-term importance of well maintained ITF databases (like STRESA) is demonstrated. - Abstract: The experimental data recorded in Integral Effect Test Facilities (ITFs) are traditionally used in order to validate best estimate (BE) system codes and to investigate the behaviour of nuclear power plants (NPPs) under accident scenarios. In the same way, facilities dedicated to specific thermal-hydraulic (TH) severe accident (SA) phenomena are used for the development and improvement of specific analytical models and codes used in the SA analysis for light water reactors (LWR). The extent to which the existing reactor safety experimental databases are preserved was well known and frequently debated and questioned in the nuclear community. The Joint Research Centre (JRC) of the European Commission (EC) has been deeply involved in several projects for experimental data production and experimental data preservation. In this context the STRESA (Storage of Thermal REactor Safety Analysis Data) web-based informatics platform was developed by JRC-Ispra in the year 2000. At present the JRC STRESA database is hosted and maintained by JRC-Petten. The Nuclear Reactor Safety Assessment Unit (NRSA) of the JRC-Petten is engaged in the administration of a new STRESA tool that secures EU storage for SA experimental data and calculations. The development of this new STRESA tool was completed by early 2015 and published on the 25/06/2015 in the URL: (http://stresa.jrc.ec.europa.eu/). The target was to keep the main features of the original STRESA structure but using the new informatics technologies that are nowadays

Qualitative tools and experimental philosophy

Science.gov (United States)

Andow, James

2016-01-01

Abstract Experimental philosophy brings empirical methods to philosophy. These methods are used to probe how people think about philosophically interesting things such as knowledge, morality, and freedom. This paper explores the contribution that qualitative methods have to make in this enterprise. I argue that qualitative methods have the potential to make a much greater contribution than they have so far. Along the way, I acknowledge a few types of resistance that proponents of qualitative methods in experimental philosophy might encounter, and provide reasons to think they are ill-founded. PMID:28392629

Development of a numerical tool for safety assessment and emergency management of experimental reactors

International Nuclear Information System (INIS)

Maas, L.; Beuter, A.; Seropian, C.

2010-01-01

The Institute of Radiological Protection and Nuclear Safety (IRSN) acts as technical support to French public authorities. Among its duties, one important item is to provide help for emergency situations management in case of an accident occurring in a French nuclear facility. In this framework, IRSN develops and applies numerical tools dealing with containment management issues. Up to now IRSN has not got any specific tool for experimental reactors. Accordingly, it has been then decided to extend the ASTEC code, devoted to severe accident scenarios for Pressurized Water Reactors, to this kind of reactors. This lumped-parameter code, co-developed by IRSN and GRS (Germany), covers the entire phenomenology from the initiating event up to fission products release outside the reactor containment, except for the steam explosion and the mechanical integrity of the containment. A first application to experimental reactors was carried out to assess the High Flux Reactor (HFR) operator's improvement proposal concerning the containment management during accidental situations. This reactor, located in Grenoble (France), is composed of a double wall containment with a pressurized containment annulus preventing any direct leakage into the environment. Until now, in case of severe accidents (mainly core melting in pool, explosive reactivity accident called BORAX), the HFR emergency management consisted in isolating the containment building in the early stage of the accident, to prevent any radioactive products release to the environment. The operator decided to improve this containment management during accidental situations by using an air filtering venting system able to maintain a slight sub-atmospheric pressure in the reactor building. The operator's demonstration of the efficiency of this new system is mainly based on containment pressure evaluations during accidental transients. IRSN assessed these calculations through ASTEC calculations. Finally, a global agreement was

Empathy as a Tool for Historical Understanding: An Evaluative Approach of the Ancient Greek Primary History Curriculum

Science.gov (United States)

Lazarakou, Elisabeth D.

2008-01-01

The present study examines the ancient Greek history curriculum and the corresponding textbook as they are implemented in the fourth grade of primary school in an aim to determine whether and to what extent empathy is recognized as a fundamental tool for historical understanding. A close examination of the curriculum revealed that empathy is not…

Experimental field study of problem-solving using tools in free-ranging capuchins (Sapajus nigritus, formerly Cebus nigritus).

Science.gov (United States)

Garber, P A; Gomes, D F; Bicca-Marques, J C

2012-04-01

Some populations of capuchins are reported to use tools to solve foraging problems in the wild. In most cases, this involves the act of pounding and digging. The use of probing tools by wild capuchins is considerably less common. Here we report on the results of an experimental field study conducted in southern Brazil designed to examine the ability of wild black-horned capuchins (Sapajus nigritus) to use a wooden dowel as a lever or a probe to obtain an embedded food reward. A group of eight capuchins was presented with two experimental platforms, each housing a clear Plexiglas box containing two bananas on a shelf and four inserted dowels. Depending on the conditions of the experiment, the capuchins were required either to pull (Condition I) or push (Conditions II and III) the dowels, in order to dislodge the food reward from the shelf so that it could be manually retrieved. In Condition I, four individuals spontaneously solved the foraging problem by pulling the dowels in 25% (72/291) of visits. In Conditions II and III, however, no capuchin successfully pushed the dowels forward to obtain the food reward. During these latter two experimental conditions, the capuchins continued to pull the dowels (41/151 or 27% of visits), even though this behavior did not result in foraging success. The results of these field experiments are consistent with an identical study conducted on wild Cebus capucinus in Costa Rica, and suggest that when using an external object as a probe to solve a foraging problem, individual capuchins were able to rapidly learn an association between the tool and the food reward, but failed to understand exactly how the tool functioned in accomplishing the task. The results also suggest that once a capuchin learned to solve this tool-mediated foraging problem, the individual persisted in using the same solution even in the face of repeated failure (slow rate of learning extinction). © 2011 Wiley Periodicals, Inc.

The predictive and external validity of the STarT Back Tool in Danish primary care.

Science.gov (United States)

Morsø, Lars; Kent, Peter; Albert, Hanne B; Hill, Jonathan C; Kongsted, Alice; Manniche, Claus

2013-08-01

The STarT Back Tool (SBT) was recently translated into Danish and its concurrent validity described. This study tested the predictive validity of the Danish SBT. Danish primary care patients (n = 344) were compared to a UK cohort. SBT subgroup validity for predicting high activity limitation at 3 months' follow-up was assessed using descriptive proportions, relative risks, AUC and odds ratios. The SBT had a statistically similar predictive ability in Danish primary care as in UK primary care. Unadjusted relative risks for poor clinical outcome on activity limitation in the Danish cohort were 2.4 (1.7-3.4) for the medium-risk subgroup and 2.8 (1.8-3.8) for the high-risk subgroup versus 3.1 (2.5-3.9) and 4.5 (3.6-5.6) for the UK cohort. Adjusting for confounders appeared to explain the lower predictive ability of the Danish high-risk group. The Danish SBT distinguished between low- and medium-risk subgroups with a similar predictive ability of the UK SBT. That distinction is useful information for informing patients about their expected prognosis and may help guiding clinicians' choice of treatment. However, cross-cultural differences in the SBT psychosocial subscale may reduce the predictive ability of the high-risk subgroup in Danish primary care.

The critical components of an electronic care plan tool for primary care: an exploratory qualitative study

Directory of Open Access Journals (Sweden)

Lisa Rotenstein

2016-07-01

Full Text Available Background A critical need exists for effective electronic tools that facilitate multidisciplinary care for complex patients in patient-centered medical homes. Objective To identify the essential components of a primary care (PC based electronic care plan (ECP tool that facilitates coordination of care for complex patients. Methods Three focus groups and nine semi-structured interviews were conducted at an academic PC practice in order to identify the ideal components of an ECP. Results Critical components of an ECP identified included: 1 patient background information, including patient demographics, care team member designation and key patient contacts, 2 user- and patient-centric task management functionalities, 3 a summary of a patient’s care needs linked to the responsible member of the care team and 4 integration with the electronic medical record. We then designed an ECP mockup incorporating these components. Conclusion Our investigation identified key principles that healthcare software developers can integrate into PC and patient-centered ECP tools.

Laser shocks: A tool for experimental simulation of damage into materials

Energy Technology Data Exchange (ETDEWEB)

Boustie, M.; Cuq Lelandais, J. P.; Berthe, L.; Ecault, R. [Institut PPRIME, Departement Physique et Mecanique des Materiaux, CNRS-ENSMA-Universite de Poitiers, 1 av Clement Ader, 86961 FUTUROSCOPE Cedex (France); CEA-DAM Valduc, 21120 Is-sur-Tille (France); Laboratoire Procedes et Ingenierie en Mecanique et Materiaux (CNRS), Arts et Metiers ParisTech, 151 bd de l' Hopital, 75013 PARIS (France); Institut PPRIME, Departement Physique et Mecanique des Materiaux, CNRS-ENSMA-Universite de Poitiers, 1 av Clement Ader, 86961 FUTUROSCOPE Cedex (France)

2012-07-30

High power laser irradiation of solids results in a strong shock wave propagation, driving very high amplitude pressure loadings with very short durations. These particular characteristics offer the possibility to study the behaviour of matter under extreme dynamic conditions in continuity with what is possible with the conventional generators of shock (launchers of projectiles, explosives). An advantage of laser shocks is a possible recovery of the shocked samples presenting the metallurgical effects of the shock in most cases. We introduce the principle of the laser shock generation, the characterization of these shocks, the principal mechanisms and effects associated with their propagation in the solids. We show how laser shocks can be a laboratory tool for simulating shock effects at ultra high strain rate, providing a high in information experimental layout for validation of damage modelling on an extended strain rate range compared to conventional shock generators. New data have been obtained with ultra short femtosecond range irradiation. Experimental data gathered through post mortem observation, time resolved velocity measurement are shown along with numerical associated simulations, showing the possibility to predict the damage behaviour of metallic targets under extreme strain rate up to 10{sup 8} s{sup -1}.

Classical experiments revisited: smartphones and tablet PCs as experimental tools in acoustics and optics

Science.gov (United States)

Klein, P.; Hirth, M.; Gröber, S.; Kuhn, J.; Müller, A.

2014-07-01

Smartphones and tablets are used as experimental tools and for quantitative measurements in two traditional laboratory experiments for undergraduate physics courses. The Doppler effect is analyzed and the speed of sound is determined with an accuracy of about 5% using ultrasonic frequency and two smartphones, which serve as rotating sound emitter and stationary sound detector. Emphasis is put on the investigation of measurement errors in order to judge experimentally derived results and to sensitize undergraduate students to the methods of error estimates. The distance dependence of the illuminance of a light bulb is investigated using an ambient light sensor of a mobile device. Satisfactory results indicate that the spectrum of possible smartphone experiments goes well beyond those already published for mechanics.

Implementation of integration strategies between primary care units and a regional general hospital in Brazil to update and connect health care professionals: a quasi-experimental study protocol.

Science.gov (United States)

Bracco, Mario Maia; Mafra, Ana Carolina Cintra Nunes; Abdo, Alexandre Hannud; Colugnati, Fernando Antonio Basile; Dalla, Marcello Dala Bernardina; Demarzo, Marcelo Marcos Piva; Abrahamsohn, Ises; Rodrigues, Aline Pacífico; Delgado, Ana Violeta Ferreira de Almeida; Dos Prazeres, Glauber Alves; Teixeira, José Carlos; Possa, Silvio

2016-08-12

Better communication among field health care teams and points of care, together with investments focused on improving teamwork, individual management, and clinical skills, are strategies for achieving better outcomes in patient-oriented care. This research aims to implement and evaluate interventions focused on improving communication and knowledge among health teams based on points of care in a regional public health outreach network, assessing the following hypotheses: 1) A better-working communication process between hospitals and primary health care providers can improve the sharing of information on patients as well as patients' outcomes. 2) A skill-upgrading education tool offered to health providers at their work sites can improve patients' care and outcomes. A quasi-experimental study protocol with a mixed-methods approach (quantitative and qualitative) was developed to evaluate communication tools for health care professionals based in primary care units and in a general hospital in the southern region of São Paulo City, Brazil. The usefulness and implementation processes of the integration strategies will be evaluated, considering: 1) An Internet-based communication platform that facilitates continuity and integrality of care to patients, and 2) A tailored updating distance-learning course on ambulatory care sensitive conditions for clinical skills improvements. The observational study will evaluate a non-randomized cohort of adult patients, with historical controls. Hospitalized patients diagnosed with an ambulatory care sensitive condition will be selected and followed for 1 year after hospital discharge. Data will be collected using validated questionnaires and from patients' medical records. Health care professionals will be evaluated related to their use of education and communication tools and their demographic and psychological profiles. The primary outcome measured will be the patients' 30-day hospital readmission rates. A sample size of 560

Validation of Nurse Practitioner Primary Care Organizational Climate Questionnaire: A New Tool to Study Nurse Practitioner Practice Settings.

Science.gov (United States)

Poghosyan, Lusine; Chaplin, William F; Shaffer, Jonathan A

2017-04-01

Favorable organizational climate in primary care settings is necessary to expand the nurse practitioner (NP) workforce and promote their practice. Only one NP-specific tool, the Nurse Practitioner Primary Care Organizational Climate Questionnaire (NP-PCOCQ), measures NP organizational climate. We confirmed NP-PCOCQ's factor structure and established its predictive validity. A crosssectional survey design was used to collect data from 314 NPs in Massachusetts in 2012. Confirmatory factor analysis and regression models were used. The 4-factor model characterized NP-PCOCQ. The NP-PCOCQ score predicted job satisfaction (beta = .36; p organizational climate in their clinics. Further testing of NP-PCOCQ is needed.

Global Sensitivity Analysis as Good Modelling Practices tool for the identification of the most influential process parameters of the primary drying step during freeze-drying.

Science.gov (United States)

Van Bockstal, Pieter-Jan; Mortier, Séverine Thérèse F C; Corver, Jos; Nopens, Ingmar; Gernaey, Krist V; De Beer, Thomas

2018-02-01

Pharmaceutical batch freeze-drying is commonly used to improve the stability of biological therapeutics. The primary drying step is regulated by the dynamic settings of the adaptable process variables, shelf temperature T s and chamber pressure P c . Mechanistic modelling of the primary drying step leads to the optimal dynamic combination of these adaptable process variables in function of time. According to Good Modelling Practices, a Global Sensitivity Analysis (GSA) is essential for appropriate model building. In this study, both a regression-based and variance-based GSA were conducted on a validated mechanistic primary drying model to estimate the impact of several model input parameters on two output variables, the product temperature at the sublimation front T i and the sublimation rate ṁ sub . T s was identified as most influential parameter on both T i and ṁ sub , followed by P c and the dried product mass transfer resistance α Rp for T i and ṁ sub , respectively. The GSA findings were experimentally validated for ṁ sub via a Design of Experiments (DoE) approach. The results indicated that GSA is a very useful tool for the evaluation of the impact of different process variables on the model outcome, leading to essential process knowledge, without the need for time-consuming experiments (e.g., DoE). Copyright © 2017 Elsevier B.V. All rights reserved.

Developmental Screening Tools: Feasibility of Use at Primary Healthcare Level in Low- and Middle-income Settings

OpenAIRE

Fischer, Vinicius Jobim; Morris, Jodi; Martines, José

2014-01-01

ABSTRACT An estimated 150 million children have a disability. Early identification of developmental disabilities is a high priority for the World Health Organization to allow action to reduce impairments through Gap Action Program on mental health. The study identified the feasibility of using the developmental screening and monitoring tools for children aged 0-3 year(s) by non-specialist primary healthcare providers in low-resource settings. A systematic review of the literature was conducte...

Keele Aches and Pains Study protocol: validity, acceptability, and feasibility of the Keele STarT MSK tool for subgrouping musculoskeletal patients in primary care

Directory of Open Access Journals (Sweden)

Campbell P

2016-10-01

Full Text Available Paul Campbell,1 Jonathan C Hill,1 Joanne Protheroe,1 Ebenezer K Afolabi,1 Martyn Lewis,1 Ruth Beardmore,1 Elaine M Hay,1 Christian D Mallen,1 Bernadette Bartlam,1 Benjamin Saunders,1 Danielle A van der Windt,1 Sue Jowett,2 Nadine E Foster,1 Kate M Dunn1 1Arthritis Research UK Primary Care Centre, Research Institute of Primary Care and Health Sciences, Keele University, Keele, 2Health Economics Unit, University of Birmingham, Birmingham, UK Abstract: Musculoskeletal conditions represent a considerable burden worldwide, and are predominantly managed in primary care. Evidence suggests that many musculoskeletal conditions share similar prognostic factors. Systematically assessing patient’s prognosis and matching treatments based on prognostic subgroups (stratified care has been shown to be both clinically effective and cost-effective. This study (Keele Aches and Pains Study aims to refine and examine the validity of a brief questionnaire (Keele STarT MSK tool designed to enable risk stratification of primary care patients with the five most common musculoskeletal pain presentations. We also describe the subgroups of patients, and explore the acceptability and feasibility of using the tool and how the tool is best implemented in clinical practice. The study design is mixed methods: a prospective, quantitative observational cohort study with a linked qualitative focus group and interview study. Patients who have consulted their GP or health care practitioner about a relevant musculoskeletal condition will be recruited from general practice. Participating patients will complete a baseline questionnaire (shortly after consultation, plus questionnaires 2 and 6 months later. A subsample of patients, along with participating GPs and health care practitioners, will be invited to take part in qualitative focus groups and interviews. The Keele STarT MSK tool will be refined based on face, discriminant, construct, and predictive validity at baseline and 2

Experimental classroom games: a didactic tool in palliative care.

Science.gov (United States)

Alonso, Ana Isabel López; Martínez, Maria Elena Fernández; Presa, Cristina Liébana; Casares, Ana Maria Vázquez; González, Maria Paz Castro

2018-01-01

Objective To evaluate the effect of a games-based intervention on palliative care nursing students' scores on the Collett-Lester Fear of Death Scale. The challenge was to innovate and integrate grief-related theory and experiences into the classroom. Method Quasi-experimental study. Before and after the games-based intervention, 101 and 111 students completed the questionnaires, respectively. The intervention was performed in the context of a palliative care class taught during the first semester of the third year of the nursing programme. Results The students obtained moderate mean scores on the variable fear of death (between 14 and 19) at both time points (pre- and post-intervention). Both men and women indicated a heightened sense of fear post-intervention and a decrease in self-perceived emotional preparedness, which support the value of the games for exposing the student to situations that closely approximated reality. Conclusion The use of games as a didactic tool in the classroom context helped the students recognize the fear generated by proximity to death in the patient and family and in the student him- or herself.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data.

Science.gov (United States)

García Nieto, Paulino José; García-Gonzalo, Esperanza; Ordóñez Galán, Celestino; Bernardo Sánchez, Antonio

2016-01-28

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC-MARS-based model was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc . Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC-MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

Directory of Open Access Journals (Sweden)

Paulino José García Nieto

2016-01-01

Full Text Available Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC in combination with multivariate adaptive regression splines (MARS technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC–MARS-based model was successfully used here to predict the milling tool flank wear (output variable as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC–MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

Science.gov (United States)

García Nieto, Paulino José; García-Gonzalo, Esperanza; Ordóñez Galán, Celestino; Bernardo Sánchez, Antonio

2016-01-01

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC–MARS-based model was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC–MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed. PMID:28787882

Intermediate Experimental Vehicle, ESA Program IXV ATDB Tool and Aerothermodynamic Characterization

Science.gov (United States)

Mareschi, Vincenzo; Ferrarella, Daniela; Zaccagnino, Elio; Tribot, Jean-Pierre; Vallee, Jean-Jacques; Haya-Ramos, Rodrigo; Rufolo, Giuseppe; Mancuso, Salvatore

2011-05-01

In the complex domain of the space technologies and among the different applications available in Europe, a great interest has been placed since several years in the development of re-entry technologies. Among the different achievements obtained in that field it is to be recalled the experience of the Atmospheric Re-entry Vehicle flight in 1998 and a certain number of important investments per-formed at Agency and national levels like Hermes, MSTP, Festip, X-38, FLPP, TRP, GSTP, HSTS, AREV, Pre-X. IXV (Intermediate eXperimental V ehicle) builds on these past experiences and studies and it is conceived to be the next technological step forward with respect to ARD With respect to previous European ballistic or quasi- ballistic demonstrators, IXV will have an increased in- flight manoeuvrability and the planned mission will allow verifying the performances of the required technologies against a wider re-entry corridor. This will imply from the pure technological aspect to increase the level of engagement on critical technologies and disciplines like aerodynamics/aerothermodynamics, guidance, navigation, control, thermal protection materials and in flight measurements. In order to support the TPS design and the other sub- systems, an AeroThermodynamicDataBase Tool has been developed by Dassault Aviation and integrated by Thales Alenia Space with the Functional Engineering Simulator (used for GNC performances evaluation) in order to characterize the aerothermodynamic behaviour of the vehicle. This paper will describe: - The methodology used to develop the ATDB tool, based on the processing of CFD computations and WTT campaigns results. - The utilization of the ATDB tool, by means of its integration into the System process. - The methodology used for the aerothermal characterization of IXV.

Fast scattering simulation tool for multi-energy x-ray imaging

Energy Technology Data Exchange (ETDEWEB)

Sossin, A., E-mail: artur.sossin@cea.fr [CEA-LETI MINATEC Grenoble, F-38054 Grenoble (France); Tabary, J.; Rebuffel, V. [CEA-LETI MINATEC Grenoble, F-38054 Grenoble (France); Létang, J.M.; Freud, N. [Université de Lyon, CREATIS, CNRS UMR5220, Inserm U1044, INSA-Lyon, Université Claude Bernard Lyon 1, Centre Léon Bérard (France); Verger, L. [CEA-LETI MINATEC Grenoble, F-38054 Grenoble (France)

2015-12-01

A combination of Monte Carlo (MC) and deterministic approaches was employed as a means of creating a simulation tool capable of providing energy resolved x-ray primary and scatter images within a reasonable time interval. Libraries of Sindbad, a previously developed x-ray simulation software, were used in the development. The scatter simulation capabilities of the tool were validated through simulation with the aid of GATE and through experimentation by using a spectrometric CdTe detector. A simple cylindrical phantom with cavities and an aluminum insert was used. Cross-validation with GATE showed good agreement with a global spatial error of 1.5% and a maximum scatter spectrum error of around 6%. Experimental validation also supported the accuracy of the simulations obtained from the developed software with a global spatial error of 1.8% and a maximum error of around 8.5% in the scatter spectra.

The Dynamics of a Doubly Clamped Microbeam Near the Primary Resonance: Experimental and Analytical Investigation

KAUST Repository

Masri, Karim M.

2016-01-20

We present experimental and analytical investigation of the dynamics of a doubly clamped microbeam near its primary resonance. The microbeam is excited electrostatically by an electrode on the first half of the beam. These microbeams are fabricated using polyimide as structural layer coated with nickel from top and chromium and gold layers from bottom. A noise signal is applied to experimentally detect the natural frequencies. Then, frequency sweep tests are generated for various values of DC bias revealing hardening, transition, and softening behavior of the microbeam. We report for the first time the transition from lower stable state, to unstable state, and then to large stable state experimentally. A multi-mode Galerkin method is used to develop a reduced order model (ROM) of the beam. Shooting method is used to find the periodic motion and is utilized to generate frequency response curves. The curves show good agreement with the experimental results with hardening behavior at lower DC voltage then softening at higher voltage loads and dynamic pull-in. © Copyright 2015 by ASME.

e-research: Changes and challenges in the use of digital tools in primary care research

DEFF Research Database (Denmark)

Bruun Larsen, Lars; Skonnord, Trygve; Gjelstad, Svein

in primary care research. Examples of this are online randomisation, electronic questionnaires, automatic email scheduling, mobile phone applications and data extraction tools. The amount of data can be increased to a low cost, and this can help to reach adequate sample sizes. However, there are still...... challenges within the field. To secure a high response rate, you need to follow up manually or use another application. There are also practical and ethical problems, and the data security for sensitive data have to be followed carefully. Session content Oral presentations about some technological...

Inflammatory pain in experimental burns in man

DEFF Research Database (Denmark)

Pedersen, J L

2000-01-01

stimuli may be more reproducible. A methodological study also demonstrated that habituation to experimental pain developed as the study proceeded. Habituation is common in experimental pain models, and dividing analgesics and placebo evenly between the study days is one way of eliminating the effects......Human experimental pain models are important tools in pain research. The primary aims of pain research in normal man is 1) to provide insight in pain mechanisms, 2) to provide a rational basis for clinical trials of pain relieving interventions, and 3) to confirm the anti-nociceptive effects...... demonstrated in animal models. Most often clinical pain is due to tissue damage leading to acute inflammation and hyperalgesia, but only few human pain models have examined pain responses in injured tissues. Therefore, models with controlled and reversible tissue trauma are needed. The human burn model...

Design of a cluster-randomized trial of electronic health record-based tools to address overweight and obesity in primary care.

Science.gov (United States)

Baer, Heather J; Wee, Christina C; DeVito, Katerina; Orav, E John; Frolkis, Joseph P; Williams, Deborah H; Wright, Adam; Bates, David W

2015-08-01

Primary care providers often fail to identify patients who are overweight or obese or discuss weight management with them. Electronic health record-based tools may help providers with the assessment and management of overweight and obesity. We describe the design of a trial to examine the effectiveness of electronic health record-based tools for the assessment and management of overweight and obesity among adult primary care patients, as well as the challenges we encountered. We developed several new features within the electronic health record used by primary care practices affiliated with Brigham and Women's Hospital in Boston, MA. These features included (1) reminders to measure height and weight, (2) an alert asking providers to add overweight or obesity to the problem list, (3) reminders with tailored management recommendations, and (4) a Weight Management screen. We then conducted a pragmatic, cluster-randomized controlled trial in 12 primary care practices. We randomized 23 clinical teams ("clinics") within the practices to the intervention group (n = 11) or the control group (n = 12). The new features were activated only for clinics in the intervention group. The intervention was implemented in two phases: the height and weight reminders went live on 15 December 2011 (Phase 1), and all of the other features went live on 11 June 2012 (Phase 2). Study enrollment went from December 2011 through December 2012, and follow-up ended in December 2013. The primary outcomes were 6-month and 12-month weight change among adult patients with body mass index ≥25 who had a visit at one of the primary care clinics during Phase 2. Secondary outcome measures included the proportion of patients with a recorded body mass index in the electronic health record, the proportion of patients with body mass index ≥25 who had a diagnosis of overweight or obesity on the electronic health record problem list, and the proportion of patients with body mass index ≥25 who had

Experimental Study on the Natural Circulation Characteristics in the Primary Loop of the SMART Reactor by using the VISTA Facility

International Nuclear Information System (INIS)

Park, Hyun-Sik; Choi, Ki-Yong; Cho, Seok; Yi, Sung-Jae; Park, Choon-Kyung; Chung, Moon-Ki

2007-01-01

The SMART uses a two-phase natural circulation in the PRHRS loop to remove the heat from the steam generators to the PRHRS heat exchangers, while a single phase natural circulation occurs in the primary loop to transfer the decay heat from the core to the steam generator. Natural circulation operation with a power range of 20 ∼ 25% was considered for SMART and nowadays the possibility of increasing the power level during the natural circulation operation is being investigated. Previously Park et al. performed several experiments by using the VISTA facility on the thermal-hydraulic characteristics of the PRHRS for the SMART-P, which includes a single-phase natural circulation in the primary loop. From the analysis with the TASS-SMR code it was shown that the reference temperature for the primary steam generator inlet temperature should be increased in order to compensate for the decreased core flow. To investigate the possibility of an increase of the power and reference temperature, it is necessary to get experimental data to characterize the natural circulation phenomena in the primary loop of the SMART. In this paper, the characteristics of natural circulation in the primary loop are experimentally investigated during various operational conditions by using the VISTA facility

Effects of Different Cutting Patterns and Experimental Conditions on the Performance of a Conical Drag Tool

Science.gov (United States)

Copur, Hanifi; Bilgin, Nuh; Balci, Cemal; Tumac, Deniz; Avunduk, Emre

2017-06-01

This study aims at determining the effects of single-, double-, and triple-spiral cutting patterns; the effects of tool cutting speeds on the experimental scale; and the effects of the method of yield estimation on cutting performance by performing a set of full-scale linear cutting tests with a conical cutting tool. The average and maximum normal, cutting and side forces; specific energy; yield; and coarseness index are measured and compared in each cutting pattern at a 25-mm line spacing, at varying depths of cut per revolution, and using two cutting speeds on five different rock samples. The results indicate that the optimum specific energy decreases by approximately 25% with an increasing number of spirals from the single- to the double-spiral cutting pattern for the hard rocks, whereas generally little effect was observed for the soft- and medium-strength rocks. The double-spiral cutting pattern appeared to be more effective than the single- or triple-spiral cutting pattern and had an advantage of lower side forces. The tool cutting speed had no apparent effect on the cutting performance. The estimation of the specific energy by the yield based on the theoretical swept area was not significantly different from that estimated by the yield based on the muck weighing, especially for the double- and triple-spiral cutting patterns and with the optimum ratio of line spacing to depth of cut per revolution. This study also demonstrated that the cutterhead and mechanical miner designs, semi-theoretical deterministic computer simulations and empirical performance predictions and optimization models should be based on realistic experimental simulations. Studies should be continued to obtain more reliable results by creating a larger database of laboratory tests and field performance records for mechanical miners using drag tools.

Evaluation of a Digital Consultation and Self-Care Advice Tool in Primary Care: A Multi-Methods Study

Directory of Open Access Journals (Sweden)

Julie Cowie

2018-05-01

Full Text Available Digital services are often regarded as a solution to the growing demands on primary care services. Provision of a tool offering advice to support self-management as well as the ability to digitally consult with a General Practitioner (GP has the potential to alleviate some of the pressure on primary care. This paper reports on a Phase II, 6-month evaluation of eConsult, a web-based triage and consultation system that was piloted across 11 GP practices across Scotland. Through a multi-method approach the evaluation explored eConsult use across practices, exposing both barriers and facilitators to its adoption. Findings suggest that expectations that eConsult would offer an additional and alternative method of accessing GP services were largely met. However, there is less certainty that it has fulfilled expectations of promoting self-help. In addition, low uptake meant that evaluation of current effectiveness was difficult for practices to quantify. The presence of an eConsult champion(s within the practice was seen to be a significant factor in ensuring successful integration of the tool. A lack of patient and staff engagement, insufficient support and lack of protocols around processes were seen as barriers to its success.

Screening of Dementia in Portuguese Primary Care: Methodology, Assessment Tools, and Main Results

Directory of Open Access Journals (Sweden)

Laetitia Teixeira

2017-11-01

Full Text Available The objectives of this article are as follows: (1 to describe the assessment protocol used to outline people with probable dementia in Primary Health Care; (2 to show the methodological design and procedure to obtain a representative sample of patients with probable dementia; and (3 to report the main characteristics of the sample collected in the context of the study “Characteristics and needs of people with probable dementia.” The study protocol was based on the “Community Assessment of Risk and Treatment Strategies (CARTS Program” and is composed by a set of instruments that allow the assessment of older adults with probable dementia in several areas (health, psychological, functionality, and other. Descriptive analysis was used to characterize the final sample (n = 436. The study protocol as well as the methodological procedure to obtain the referral of research participants and data collection on the condition of people with probable dementia in Primary Health Care proved to be a valuable tool to obtain a sample of patients distributed by the full range of probable dementia in a large geographical area. Results may allocate the design of care pathways for old people with cognitive disorders to prevent, delay impairment, and/or optimize quality of life of patients.

Primary Retinal Cultures as a Tool for Modeling Diabetic Retinopathy: An Overview

Directory of Open Access Journals (Sweden)

Andrea Matteucci

2015-01-01

Full Text Available Experimental models of diabetic retinopathy (DR have had a crucial role in the comprehension of the pathophysiology of the disease and the identification of new therapeutic strategies. Most of these studies have been conducted in vivo, in animal models. However, a significant contribution has also been provided by studies on retinal cultures, especially regarding the effects of the potentially toxic components of the diabetic milieu on retinal cell homeostasis, the characterization of the mechanisms on the basis of retinal damage, and the identification of potentially protective molecules. In this review, we highlight the contribution given by primary retinal cultures to the study of DR, focusing on early neuroglial impairment. We also speculate on possible themes into which studies based on retinal cell cultures could provide deeper insight.

Development of thick wall welding and cutting tools for ITER

International Nuclear Information System (INIS)

Nakahira, Masataka; Takahashi, Hiroyuki; Akou, Kentaro; Koizumi, Koichi

1998-01-01

The Vacuum Vessel, which is a core component of International Thermonuclear Experimental Reactor (ITER), is required to be exchanged remotely in a case of accident such as superconducting coil failure. The in-vessel components such as blanket and divertor are planned to be exchanged or fixed. In these exchange or maintenance operations, the thick wall welding and cutting are inevitable and remote handling tools are necessary. The thick wall welding and cutting tools for blanket are under developing in the ITER R and D program. The design requirement is to weld or cut the stainless steel of 70 mm thickness in the narrow space. Tungsten inert gas (TIG) arc welding, plasma cutting and iodine laser welding/cutting are selected as primary option. Element welding and cutting tests, design of small tools to satisfy space requirement, test fabrication and performance tests were performed. This paper reports the tool design and overview of welding and cutting tests. (author)

Development of thick wall welding and cutting tools for ITER

Energy Technology Data Exchange (ETDEWEB)

Nakahira, Masataka; Takahashi, Hiroyuki; Akou, Kentaro; Koizumi, Koichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-04-01

The Vacuum Vessel, which is a core component of International Thermonuclear Experimental Reactor (ITER), is required to be exchanged remotely in a case of accident such as superconducting coil failure. The in-vessel components such as blanket and divertor are planned to be exchanged or fixed. In these exchange or maintenance operations, the thick wall welding and cutting are inevitable and remote handling tools are necessary. The thick wall welding and cutting tools for blanket are under developing in the ITER R and D program. The design requirement is to weld or cut the stainless steel of 70 mm thickness in the narrow space. Tungsten inert gas (TIG) arc welding, plasma cutting and iodine laser welding/cutting are selected as primary option. Element welding and cutting tests, design of small tools to satisfy space requirement, test fabrication and performance tests were performed. This paper reports the tool design and overview of welding and cutting tests. (author)

Boosted top: experimental tools overview

CERN Document Server

Usai, Emanuele

2015-01-01

An overview of tools and methods for the reconstruction of high-boost top quark decays at the LHC is given in this report. The focus is on hadronic decays, in particular an overview of the current status of top quark taggers in physics analyses is presented. The most widely used jet substructure techniques, normally used in combination with top quark taggers, are reviewed. Special techniques to treat pileup in large cone jets are described, along with a comparison of the performance of several boosted top quark reconstruction techniques.

Development and experimental validation of a tool to determine out-of-field dose in radiotherapy

International Nuclear Information System (INIS)

Bessieres, I.

2013-01-01

Over the last two decades, many technical developments have been achieved on intensity modulated radiotherapy (IMRT) and allow a better conformation of the dose to the tumor and consequently increase the success of cancer treatments. These techniques often reduce the dose to organs at risk close to the target volume; nevertheless they increase peripheral dose levels. In this situation, the rising of the survival rate also increases the probability of secondary effects expression caused by peripheral dose deposition (second cancers for instance). Nowadays, the peripheral dose is not taken into account during the treatment planning and no reliable prediction tool exists. However it becomes crucial to consider the peripheral dose during the planning, especially for pediatric cases. Many steps of the development of an accurate and fast Monte Carlo out-of-field dose prediction tool based on the PENELOPE code have been achieved during this PhD work. To this end, we demonstrated the ability of the PENELOPE code to estimate the peripheral dose by comparing its results with reference measurements performed on two experimental configurations (metrological and pre-clinical). During this experimental work, we defined a protocol for low doses measurement with OSL dosimeters. In parallel, we highlighted the slow convergence of the code for clinical use. Consequently, we accelerated the code by implementing a new variance reduction technique called pseudo-deterministic transport which is specifically with the objective of improving calculations in areas far away from the beam. This step improved the efficiency of the peripheral doses estimation in both validation configurations (by a factor of 20) in order to reach reasonable computing times for clinical application. Optimization works must be realized in order improve the convergence of our tool and consider a final clinical use. (author) [fr

Transposons As Tools for Functional Genomics in Vertebrate Models.

Science.gov (United States)

Kawakami, Koichi; Largaespada, David A; Ivics, Zoltán

2017-11-01

Genetic tools and mutagenesis strategies based on transposable elements are currently under development with a vision to link primary DNA sequence information to gene functions in vertebrate models. By virtue of their inherent capacity to insert into DNA, transposons can be developed into powerful tools for chromosomal manipulations. Transposon-based forward mutagenesis screens have numerous advantages including high throughput, easy identification of mutated alleles, and providing insight into genetic networks and pathways based on phenotypes. For example, the Sleeping Beauty transposon has become highly instrumental to induce tumors in experimental animals in a tissue-specific manner with the aim of uncovering the genetic basis of diverse cancers. Here, we describe a battery of mutagenic cassettes that can be applied in conjunction with transposon vectors to mutagenize genes, and highlight versatile experimental strategies for the generation of engineered chromosomes for loss-of-function as well as gain-of-function mutagenesis for functional gene annotation in vertebrate models, including zebrafish, mice, and rats. Copyright © 2017 Elsevier Ltd. All rights reserved.

EXPERIMENTAL MONTAGE USED TO STUDY THE VIBRATION OF THE DRILL TOOL IN THE PROCESS OF MANUFACTURING THE BRONZE MATERIALS

Directory of Open Access Journals (Sweden)

Cosmin-Mihai MIRIŢOIU

2013-05-01

Full Text Available In this paper we present the experimental setup used to study the vibration of the drill tool, during the drilling of the bronze products. In this paper the vibrations are analyzed during the drilling on the universal lathe machines. This time, the tool is fixed in the movable boring head and will make a translation movement with constant feeding, and the workpiece spins around its axis of symmetry and it is fixed in the spindle head stock of the universal lathe machine

Experimental Study of Tool Wear and Grinding Forces During BK-7 Glass Micro-grinding with Modified PCD Tool

Science.gov (United States)

Pratap, A.; Sahoo, P.; Patra, K.; Dyakonov, A. A.

2017-09-01

This study focuses on the improvement in grinding performance of BK-7 glass using polycrystalline diamond micro-tool. Micro-tools are modified using wire EDM and performance of modified tools is compared with that of as received tool. Tool wear of different types of tools are observed. To quantify the tool wear, a method based on weight loss of tool is introduced in this study. Modified tools significantly reduce tool wear in comparison to the normal tool. Grinding forces increase with machining time due to tool wear. However, modified tools produce lesser forces thus can improve life of the PCD micro-grinding tool.

Experimental Investigation of Surface Layer Properties of High Thermal Conductivity Tool Steel after Electrical Discharge Machining

Directory of Open Access Journals (Sweden)

Rafał Świercz

2017-12-01

Full Text Available New materials require the use of advanced technology in manufacturing complex shape parts. One of the modern materials widely used in the tool industry for injection molds or hot stamping dies is high conductivity tool steel (HTCS 150. Due to its hardness (55 HRC and thermal conductivity at 66 W/mK, this material is difficult to machine by conventional treatment and is being increasingly manufactured by nonconventional technology such as electrical discharge machining (EDM. In the EDM process, material is removed from the workpiece by a series of electrical discharges that cause changes to the surface layers properties. The final state of the surface layer directly influences the durability of the produced elements. This paper presents the influence of EDM process parameters: discharge current Ic and the pulse time ton on surface layer properties. The experimental investigation was carried out with an experimental methodology design. Surface layers properties including roughness 3D parameters, the thickness of the white layer, heat affected zone, tempered layer and occurring micro cracks were investigated and described. The influence of the response surface methodology (RSM of discharge current Ic and the pulse time ton on the thickness of the white layer and roughness parameters Sa, Sds and Ssc were described and established.

TRIP-ID: A tool for a smart and interactive identification of Magic Formula tyre model parameters from experimental data acquired on track or test rig

Science.gov (United States)

Farroni, Flavio; Lamberti, Raffaele; Mancinelli, Nicolò; Timpone, Francesco

2018-03-01

Tyres play a key role in ground vehicles' dynamics because they are responsible for traction, braking and cornering. A proper tyre-road interaction model is essential for a useful and reliable vehicle dynamics model. In the last two decades Pacejka's Magic Formula (MF) has become a standard in simulation field. This paper presents a Tool, called TRIP-ID (Tyre Road Interaction Parameters IDentification), developed to characterize and to identify with a high grade of accuracy and reliability MF micro-parameters from experimental data deriving from telemetry or from test rig. The tool guides interactively the user through the identification process on the basis of strong diagnostic considerations about the experimental data made evident by the tool itself. A motorsport application of the tool is shown as a case study.

Understanding organometallic reaction mechanisms and catalysis experimental and computational tools computational and experimental tools

CERN Document Server

Ananikov, Valentin P

2014-01-01

Exploring and highlighting the new horizons in the studies of reaction mechanisms that open joint application of experimental studies and theoretical calculations is the goal of this book. The latest insights and developments in the mechanistic studies of organometallic reactions and catalytic processes are presented and reviewed. The book adopts a unique approach, exemplifying how to use experiments, spectroscopy measurements, and computational methods to reveal reaction pathways and molecular structures of catalysts, rather than concentrating solely on one discipline. The result is a deeper

Modeling the milling tool wear by using an evolutionary SVM-based model from milling runs experimental data

Science.gov (United States)

Nieto, Paulino José García; García-Gonzalo, Esperanza; Vilán, José Antonio Vilán; Robleda, Abraham Segade

2015-12-01

The main aim of this research work is to build a new practical hybrid regression model to predict the milling tool wear in a regular cut as well as entry cut and exit cut of a milling tool. The model was based on Particle Swarm Optimization (PSO) in combination with support vector machines (SVMs). This optimization mechanism involved kernel parameter setting in the SVM training procedure, which significantly influences the regression accuracy. Bearing this in mind, a PSO-SVM-based model, which is based on the statistical learning theory, was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. To accomplish the objective of this study, the experimental dataset represents experiments from runs on a milling machine under various operating conditions. In this way, data sampled by three different types of sensors (acoustic emission sensor, vibration sensor and current sensor) were acquired at several positions. A second aim is to determine the factors with the greatest bearing on the milling tool flank wear with a view to proposing milling machine's improvements. Firstly, this hybrid PSO-SVM-based regression model captures the main perception of statistical learning theory in order to obtain a good prediction of the dependence among the flank wear (output variable) and input variables (time, depth of cut, feed, etc.). Indeed, regression with optimal hyperparameters was performed and a determination coefficient of 0.95 was obtained. The agreement of this model with experimental data confirmed its good performance. Secondly, the main advantages of this PSO-SVM-based model are its capacity to produce a simple, easy-to-interpret model, its ability to estimate the contributions of the input variables, and its computational efficiency. Finally, the main conclusions of this study are exposed.

RADON PROGENY AS AN EXPERIMENTAL TOOL FOR DOSIMETRY OF NANOAEROSOLS

Energy Technology Data Exchange (ETDEWEB)

Ruzer, Lev; Ruzer, Lev S.; Apte, Michael G.

2008-02-25

The study of aerosol exposure and dosimetry measurements and related quantitation of health effects are important to the understanding of the consequences of air pollution, and are discussed widely in the scientific literature. During the last 10 years the need to correlate aerosol exposure and biological effects has become especially important due to rapid development of a new, revolutionary industry ?-- nanotechnology. Nanoproduct commerce is predicted to top $1 trillion by 2015. Quantitative assessment of aerosol particle behavior in air and in lung deposition, and dosimetry in different parts of the lung, particularly for nanoaerosols, remains poor despite several decades of study. Direct measurements on humans are still needed in order to validate the hollow cast, animal studies, and lung deposition modeling. We discuss here the use of nanoscale radon decay products as an experimental tool in the study of local deposition and lung dosimetry for nanoaerosols. The issue of the safe use of radon progeny in such measurements is discussed based on a comparison of measured exposure in 3 settings: general population, miners, and in a human experiment conducted at the Paul Scherer Institute (PSI) in Switzerland. One of the properties of radon progeny is that they consist partly of 1 nm radioactive particles called unattached activity; having extremely small size and high diffusion coefficients, these particles can be potentially useful as radioactive tracers in the study of nanometer-sized aerosols. We present a theoretical and experimental study of the correlation between the unattached activity and aerosol particle surface area, together with a description of its calibration and method for measurement of the unattached fraction.

EXPERIMENTAL INVESTIGATION OF THE TOOL-CHIP INTERFACE TMPERATURES ON UNCOATED CEMENTIDE CARBIDE CUTTING TOOLS

Directory of Open Access Journals (Sweden)

Kasım HABALI

2005-01-01

Full Text Available It is known that the temperature as the result of the heat developed during machining at the tool-chip interface has an influence on the tool life and workpiece surface guality and the methods for measuring this temperature are constantly under investigation. In this study, the measurement of tool-chip interface temperature using toolworkpiece termocouple method was investigated. The test were carried out on a AISI 1040 steel and the toolchip interface temperature variation was examined depending on the cutting speed and feed rate. The obtained groups show that cutting speed has more influence on the temperature than feedrate has.

Probing the mutational interplay between primary and promiscuous protein functions: a computational-experimental approach.

Science.gov (United States)

Garcia-Seisdedos, Hector; Ibarra-Molero, Beatriz; Sanchez-Ruiz, Jose M

2012-01-01

Protein promiscuity is of considerable interest due its role in adaptive metabolic plasticity, its fundamental connection with molecular evolution and also because of its biotechnological applications. Current views on the relation between primary and promiscuous protein activities stem largely from laboratory evolution experiments aimed at increasing promiscuous activity levels. Here, on the other hand, we attempt to assess the main features of the simultaneous modulation of the primary and promiscuous functions during the course of natural evolution. The computational/experimental approach we propose for this task involves the following steps: a function-targeted, statistical coupling analysis of evolutionary data is used to determine a set of positions likely linked to the recruitment of a promiscuous activity for a new function; a combinatorial library of mutations on this set of positions is prepared and screened for both, the primary and the promiscuous activities; a partial-least-squares reconstruction of the full combinatorial space is carried out; finally, an approximation to the Pareto set of variants with optimal primary/promiscuous activities is derived. Application of the approach to the emergence of folding catalysis in thioredoxin scaffolds reveals an unanticipated scenario: diverse patterns of primary/promiscuous activity modulation are possible, including a moderate (but likely significant in a biological context) simultaneous enhancement of both activities. We show that this scenario can be most simply explained on the basis of the conformational diversity hypothesis, although alternative interpretations cannot be ruled out. Overall, the results reported may help clarify the mechanisms of the evolution of new functions. From a different viewpoint, the partial-least-squares-reconstruction/Pareto-set-prediction approach we have introduced provides the computational basis for an efficient directed-evolution protocol aimed at the simultaneous

Fernald Silo Remote Retrieval Tool Development

International Nuclear Information System (INIS)

Varma, V.K.

2004-01-01

A long-reach tool was developed to remove discrete objects from the silos at the Fernald Environmental Management Project in Ohio. If they are not removed, these objects can potentially cause problems during the retrieval and transfer of waste from the silos. Most of the objects are on top of the Bentogrout cap inside the silos at or near the primary opening into the tank and will therefore require only vertical lifting. The objects are located about 20 ft from the top of the silo. Although most of the objects can be retrieved from 20 ft, the long-reach tool was designed to for a reach up to 40 ft in case objects roll towards the walls of the tank or need to be removed during heel retrieval operations. This report provides a detailed description of the tool that was developed, tested, and demonstrated at the Tanks Technology Cold Test Facility at Oak Ridge National Laboratory. Scaffolding was erected over two experimental cells to simulate the 40-ft maximum working depth anticipated in the silos at Fernald. Plastic bottles and plastic sheeting simulated the debris that could be encountered during waste retrieval operations

Application of a LiFePO4 Battery Energy Storage System to Primary Frequency Control: Simulations and Experimental Results

Directory of Open Access Journals (Sweden)

Fabio Massimo Gatta

2016-10-01

Full Text Available This paper presents an experimental application of LiFePO4 battery energy storage systems (BESSs to primary frequency control, currently being performed by Terna, the Italian transmission system operator (TSO. BESS performance in the primary frequency control role was evaluated by means of a simplified electrical-thermal circuit model, taking into account also the BESS auxiliary consumptions, coupled with a cycle-life model, in order to assess the expected life of the BESS. Numerical simulations have been carried out considering the system response to real frequency measurements taken in Italy, spanning a whole year; a parametric study taking into account different values of governor droop and of BESS charge/discharge rates (C-rates was also performed. Simulations, fully validated by experimental results obtained thus far, evidenced a severe trade-off between expected lifetime and overall efficiency, which significantly restricts the choice of operating parameters for frequency control.

CATHARE-2 prediction of large primary to secondary leakage (PRISE) at PSB-VVER experimental facility

Energy Technology Data Exchange (ETDEWEB)

Sabotinov, L.; Chevrier, P. [Institut de Radioprotection et de Surete Nucleaire, 92 - Fontenay aux Roses (France)

2007-07-01

The large primary to secondary leakage (PRISE) is a specific loss-of-coolant accident in VVER reactors, related to the break of the steam generator collector cover, leading to loss of primary mass inventory and possible direct radioactive release to atmosphere. The best estimate thermal-hydraulic computer code CATHARE-2 Version 2.5-1 was used for post-test analysis of a PRISE experiment, conducted at the large scale test facility PSB-VVER in Russia. The PSB rig is 1:300 scaled model of VVER-1000 NPP. The accident is calculated with a 1.4% break size, which corresponds to 100 mm leak from primary to secondary side in the real NPP. A computer model has been developed for CATHARE-2 V2.5-1, taking into account all important components of the PSB facility: reactor model (lower plenum, core, bypass, upper plenum, downcomer), 4 separate loops, pressurizer, horizontal multi-tube steam generators, break section. The secondary side is presented by recirculation model. A large number of sensitivity calculations has been performed regarding break modeling, reactor pressure vessel modeling, counter current flow modeling, hydraulic losses, heat losses, steam generator level regulation. Comparison between calculated and experimental results shows good prediction of the basic thermal-hydraulic phenomena and parameters such as primary and secondary pressures, temperatures, loop flows, etc. Some discrepancies were observed in the calculations of primary mass inventory and loop seal clearance. Nevertheless the final core heat up, which is one of the most important safety criteria, was correctly predicted. (authors)

Experimental Validation of an FSW Model with an Enhanced Friction Law: Application to a Threaded Cylindrical Pin Tool

Directory of Open Access Journals (Sweden)

Narges Dialami

2017-11-01

Full Text Available This work adopts a fast and accurate two-stage computational strategy for the analysis of FSW (Friction stir welding processes using threaded cylindrical pin tools. The coupled thermo-mechanical problem is equipped with an enhanced friction model to include the effect of non-uniform pressure distribution under the pin shoulder. The overall numerical strategy is successfully validated by the experimental measurements provided by the industrial partner (Sapa. The verification of the numerical model using the experimental evidence is not only accomplished in terms of temperature evolution but also in terms of torque, longitudinal, transversal and vertical forces.

Optimization of Surface Finish in Turning Operation by Considering the Machine Tool Vibration using Taguchi Method

Directory of Open Access Journals (Sweden)

Muhammad Munawar

2012-01-01

Full Text Available Optimization of surface roughness has been one of the primary objectives in most of the machining operations. Poor control on the desired surface roughness generates non conforming parts and results into increase in cost and loss of productivity due to rework or scrap. Surface roughness value is a result of several process variables among which machine tool condition is one of the significant variables. In this study, experimentation was carried out to investigate the effect of machine tool condition on surface roughness. Variable used to represent machine tool\\'s condition was vibration amplitude. Input parameters used, besides vibration amplitude, were feed rate and insert nose radius. Cutting speed and depth of cut were kept constant. Based on Taguchi orthogonal array, a series of experimentation was designed and performed on AISI 1040 carbon steel bar at default and induced machine tool\\'s vibration amplitudes. ANOVA (Analysis of Variance, revealed that vibration amplitude and feed rate had moderate effect on the surface roughness and insert nose radius had the highest significant effect on the surface roughness. It was also found that a machine tool with low vibration amplitude produced better surface roughness. Insert with larger nose radius produced better surface roughness at low feed rate.

Evaluation of bone loss due to primary occlusal trauma in two experimental models of occlusal overload

OpenAIRE

LOPES, Ana Cristina Távora de Albuquerque; TÉO, Mirela Anne Quartaroli; CORRÊA, Mônica Grazieli; ISHIKIRIAMA, Bella Luna Colombini; CAMPOS, Mirella Lindoso Gomes

2016-01-01

Abstract Introduction Primary occlusal trauma (OT) is an injury of the periodontium with normal height as a result of occlusal forces which exceed their adaptive capacity. Objective To evaluate, histometrically, the alveolar bone loss in the furcation region of rats experimentally submitted to 2 models of occlusal overload. Material and method 45 animals randomly divided into 3 groups: Occlusal Interference (OI, n = 15) - fixing an orthodontic wire segment on the occlusal surface of the fi...

Smartphones as Experimental Tools: Different Methods to Determine the Gravitational Acceleration in Classroom Physics by Using Everyday Devices

Science.gov (United States)

Kuhn, Jochen; Vogt, Patrik

2013-01-01

New media technology becomes more and more important for our daily life as well as for teaching physics. Within the scope of our N.E.T. research project we develop experiments using New Media Experimental Tools (N.E.T.) in physics education and study their influence on students learning abilities. We want to present the possibilities e.g. of…

Multifactorial screening for fall risk in community-dwelling older adults in the primary care office: development of the fall risk assessment & screening tool.

Science.gov (United States)

Renfro, Mindy Oxman; Fehrer, Steven

2011-01-01

Unintentional falls is an increasing public health problem as incidence of falls rises and the population ages. The Centers for Disease Control and Prevention reports that 1 in 3 adults aged 65 years and older will experience a fall this year; 20% to 30% of those who fall will sustain a moderate to severe injury. Physical therapists caring for older adults are usually engaged with these patients after the first injury fall and may have little opportunity to abate fall risk before the injuries occur. This article describes the content selection and development of a simple-to-administer, multifactorial, Fall Risk Assessment & Screening Tool (FRAST), designed specifically for use in primary care settings to identify those older adults with high fall risk. Fall Risk Assessment & Screening Tool incorporates previously validated measures within a new multifactorial tool and includes targeted recommendations for intervention. Development of the multifactorial FRAST used a 5-part process: identification of significant fall risk factors, review of best evidence, selection of items, creation of the scoring grid, and development of a recommended action plan. Fall Risk Assessment & Screening Tool has been developed to assess fall risk in the target population of older adults (older than 65 years) living and ambulating independently in the community. Many fall risk factors have been considered and 15 items selected for inclusion. Fall Risk Assessment & Screening Tool includes 4 previously validated measures to assess balance, depression, falls efficacy, and home safety. Reliability and validity studies of FRAST are under way. Fall risk for community-dwelling older adults is an urgent, multifactorial, public health problem. Providing primary care practitioners (PCPs) with a very simple screening tool is imperative. Fall Risk Assessment & Screening Tool was created to allow for safe, quick, and low-cost administration by minimally trained office staff with interpretation and

An assessment of the effect of an experimental environmental education programme (Man and Nutrition) on Kuwaiti primary school pupils (Grade Four)

Science.gov (United States)

Esmaeel, Yaqoub Y. R.

The educational system in Kuwait is undergoing some fundamental changes, and the need for reform of environmental education has become urgent as a result of the concerns of both the government and the public over environmental issues. It is in such a context that this research was conducted. The research was intended to develop, implement, and evaluate an experimental programme Man and Nutrition for Kuwaiti primary school pupils, aimed at developing a positive environmental achievement, Information about the present status of environmental concepts and environmental education in Kuwait was obtained from preliminary study such as interviews and curriculum analysis. Interviews were conducted in ten different primary schools in four districts in Kuwait, which involved 31 pupils in total, hi addition, information was obtained by analysis of the science curriculum for fourth grade primary schools. The preliminary study was carried out during the period April to October 1998. The results of the preliminary study served to aid the development of an experimental teaching programme. The experimental programme Man and Nutrition consisted of eight lessons printed in two booklets, a teacher's guide and pupil's textbook. The research included a review of the relevant literature examining the development of environmental programmes and activities in a number of countries, which were selected because of their environmental education approaches, and the variety of their environmental conditions. Pilot testing of the teaching programmes was carried out to ascertain the appropriateness of the materials and the data collecting instruments used for the evaluation of the main experimental study. The main study group included 115 pupils in four primary schools and four teachers selected in Kuwait. Data collecting included pre and post-tests and the course evaluation by teachers using semi-structured interviews. Statistical analysis of data obtained was carried out using the SPSS

Experimental activities in the early years of elementary school: a methodological tool for construction of the teaching-learning process

Directory of Open Access Journals (Sweden)

Ana de Souza Lima

2017-07-01

Full Text Available Focusing on the early years of elementary school, this study evaluated the impact of experimental activities based in the scientific method and preconceptions on the learning and memorization of concepts and phenomena associated with the fermentation process. The different activities were carried out through an experimental course (20hs, with students of elementary school from school municipal Diacono Joao Luiz Pozzobon, Santa Maria-RS. The research involved 20 students, with 6 and 7 old years. The evaluation was performed by comparing the interview responses made before the course (pre-test and after the course (post-test. The post-tests were applied at the end of the experimental course, and after 6 and 12 months. The experimental activities facilitated the acquisition and retention of new concepts. The data show that "experimental activities" can be used by teachers in early grades as a methodological tool to complement the teaching-learning process.

Macrolithic tools for mining and primary processing of metal ores from the site of Grotta della Monaca (Calabria, Italy

Directory of Open Access Journals (Sweden)

Francesco Breglia

2016-10-01

In this paper we focus on two categories of macrolithic tools: those used to extract minerals, and those used for their primary processing. The first group is composed of 51 artefacts divided into axes, hammers, and pickaxes with a central groove, found in the deeper areas of the cave, which represent the mining areas. Their morphological and dimensional variability indicates a significant functional diversification; furthermore, the choice of different very hard metamorphic rocks implies a high awareness in the selection of the raw materials used for making these implements. The second group includes 22 tools with different functions - mainly made of sandstone - classified as querns, grinders and crushers. They were found in an underground area adjacent to the entrance, which is characterized by large and comfortable spaces, with the widespread presence of natural light. A recent traceological study has clarified the function of such artefacts; they were used to grind mined blocks of iron hydroxides to obtain a powder. The multidisciplinary approach adopted in studying mining tools from Grotta della Monaca, including petrographic, typological and use-wear analysis, has allowed us to gain important knowledge about the general characteristics of these tools.

Predictive Validity of the STarT Back Tool for Risk of Persistent Disabling Back Pain in a U.S Primary Care Setting.

Science.gov (United States)

Suri, Pradeep; Delaney, Kristin; Rundell, Sean D; Cherkin, Daniel C

2018-04-03

To examine the predictive validity of the Subgrouping for Targeted Treatment (STarT Back) tool for classifying people with back pain into categories of low, medium, and high risk of persistent disabling back pain in U.S. primary care. Secondary analysis of data from participants receiving usual care in a randomized clinical trial. Primary care clinics. Adults (N = 1109) ≥18 years of age with back pain. Those with specific causes of back pain (pregnancy, disc herniation, vertebral fracture, spinal stenosis) and work-related injuries were not included. Not applicable. The original 9-item version of the STarT Back tool, administered at baseline, stratified patients by their risk (low, medium, high) of persistent disabling back pain (STarT Back risk group). Persistent disabling back pain was defined as Roland-Morris Disability Questionnaire scores of ≥7 at 6-month follow-up. The STarT Back risk group was a significant predictor of persistent disabling back pain (PSTarT Back risk groups successfully separated people with back pain into distinct categories of risk for persistent disabling back pain at 6-month follow-up in U.S. primary care. These results were very similar to those in the original STarT Back validation study. This validation study is a necessary first step toward identifying whether the entire STarT Back approach, including matched/targeted treatment, can be effectively used for primary care in the United States. Published by Elsevier Inc.

Case-mix tool, costs and effectiveness in improving primary care mental health and substance abuse services.

Science.gov (United States)

Riihimäki, Kirsi; Heiska-Johansson, Ainomaija; Ketola, Eeva

2018-02-01

Despite its importance in improving care and developing services, high-quality data evaluating cost-effectiveness and services in different case-mix populations is scarce in primary care. The objective was to investigate the service use of those mental health and substance abuse patients, who use lots of services. Primary health care diagnosis-related groups (pDRG) is a tool to evaluate service provider system and improve efficiency, productivity and quality. We viewed all pDRG results available from the year 2015 concerning municipal mental health and substance abuse services. In primary care mental health and substance abuse services, the most common ICD-10-codes were depression and substance abuse. One-fifth of patients produced 57% of costs. Their medium of appointments was 16 per year versus 6 per year of all patients. Only 54% of their diagnoses were recorded in the electronic health records versus 75% of all patients. They made 5.7 different pDRG episodes, including 1.8 episodes of depression, per patient. The average episode cost for this patient group was 301€. pDRG makes health care production transparent also in mental health and substance abuse services. It is easy to identify patients, who use a lot of services and thus induce the majority of costs, and focus on their needs in managing and developing services.

An experimental study of hafting adhesives and the implications for compound tool technology.

Science.gov (United States)

Zipkin, Andrew M; Wagner, Mark; McGrath, Kate; Brooks, Alison S; Lucas, Peter W

2014-01-01

Experimental studies of hafting adhesives and modifications to compound tool components can demonstrate the extent to which human ancestors understood and exploited material properties only formally defined by science within the last century. Discoveries of Stone Age hafting adhesives at archaeological sites in Europe, the Middle East, and Africa have spurred experiments that sought to replicate or create models of such adhesives. Most of these studies, however, have been actualistic in design, focusing on replicating ancient applications of adhesive technology. In contrast, this study tested several glues based on Acacia resin within a materials science framework to better understand the effect of each adhesive ingredient on compound tool durability. Using an overlap joint as a model for a compound tool, adhesives formulated with loading agents from a range of particle sizes and mineral compositions were tested for toughness on smooth and rough substrates. Our results indicated that overlap joint toughness is significantly increased by using a roughened joint surface. Contrary to some previous studies, there was no evidence that particle size diversity in a loading agent improved adhesive effectiveness. Generally, glues containing quartz or ochre loading agents in the silt and clay-sized particle class yielded the toughest overlap joints, with the effect of particle size found to be more significant for rough rather than smooth substrate joints. Additionally, no particular ochre mineral or mineral mixture was found to be a clearly superior loading agent. These two points taken together suggest that Paleolithic use of ochre-loaded adhesives and the criteria used to select ochres for this purpose may have been mediated by visual and symbolic considerations rather than purely functional concerns.

Assessing primary care in Austria: room for improvement.

Science.gov (United States)

Stigler, Florian L; Starfield, Barbara; Sprenger, Martin; Salzer, Helmut J F; Campbell, Stephen M

2013-04-01

There is emerging evidence that strong primary care achieves better health at lower costs. Although primary care can be measured, in many countries, including Austria, there is little understanding of primary care development. Assessing the primary care development in Austria. A primary care assessment tool developed by Barbara Starfield in 1998 was implemented in Austria. This tool defines 15 primary care characteristics and distinguishes between system and practice characteristics. Each characteristic was evaluated by six Austrian primary care experts and rated as 2 (high), 1 (intermediate) or 0 (low) points, respectively, to their primary care strength (maximum score: n = 30). Austria received 7 out of 30 points; no characteristic was rated as '2' but 8 were rated as '0'. Compared with the 13 previously assessed countries, Austria ranks 10th of 14 countries and is classified as a 'low primary care' country. This study provides the first evidence concerning primary care in Austria, benchmarking it as weak and in need of development. The practicable application of an existing assessment tool can be encouraging for other countries to generate evidence about their primary care system as well.

Using shell tools in Mesolithic and early Neolithic coastal sites from Northern Spain: experimental program for use wear analysis in malacological materials

Directory of Open Access Journals (Sweden)

Cuenca Solana, David

2010-06-01

Full Text Available One of the most common debates surrounding the Mesolithic and early Neolithic periods in northern Spain focuses on the scarcity of lithic and osseous technologies identified in large shell midden contexts. Currently, several hypotheses have been proposed that attribute this phenomenon to differences in site spatial organization, increases in perishable material use, or changes in subsistence strategies. However, recently shell tools have been identified in the early Neolithic levels at Santimamiñe cave located in the Basque Country of northern Spain. These artifacts are the first evidence of shell tools to be identified in Northern Spain in an early Neolithic shell midden context. This paper proposes the hypothesis that shell tools were being used in subsistence activities. To test this hypothesis, the authors developed an experimental programme using different types of mollusc shells to examine evidence of functional use on wood, dry/fresh animal skin and non-woody plants. The experimental results were then used to examine the patterns of use on the seven shell tools from Santimamiñe. The results of the comparisons indicate that the seven shell tools have similar use patterns as the experimental shells. This evidence supports the proposed hypothesis that shell tools may have been used frequently in shell midden contexts during the Mesolithic and early Neolithic for the working of wood, plants or animal skin.

Uno de los debates más extendidos en la historiografía sobre el Mesolítico y el Neolítico inicial en la región cantábrica es el de la escasez de tecnologías “tradicionales” en la mayor parte de los contextos existentes, especialmente en aquellos con grandes acumulaciones de conchas. Actualmente, varias de las hipótesis propuestas atribuyen este fenómeno a diferencias en la organización espacial de los asentamientos, al aumento en la utilización de materiales perecederos o a cambios en las estrategias de subsistencia

Process Machine Interactions Predicition and Manipulation of Interactions between Manufacturing Processes and Machine Tool Structures

CERN Document Server

Hollmann, Ferdinand

2013-01-01

This contributed volume collects the scientific results of the DFG Priority Program 1180 Prediction and Manipulation of Interactions between Structure and Process. The research program has been conducted during the years 2005 and 2012, whereas the primary goal was the analysis of the interactions between processes and structures in modern production facilities. This book presents the findings of the 20 interdisciplinary subprojects, focusing on different manufacturing processes such as high performance milling, tool grinding or metal forming. It contains experimental investigations as well as mathematical modeling of production processes and machine interactions. New experimental advancements and novel simulation approaches are also included.

Innovations in Primary Health Care: the use of communications technology and information tools to support local management.

Science.gov (United States)

Pinto, Luiz Felipe; Rocha, Cristianne Maria Famer

2016-05-01

Social media has been used in different contexts as a way to streamline the flow of data and information for decision making. This has contributed to the issue of knowledge production in networks and the expansion of communication channels so that there is greater access to health services. This article describes the results of research done on 16 Information Technology and Communications Observatories in Health Care - OTICS Network in Rio - covering the Municipal Health Secretariat in Rio de Janeiro which supported the integration of primary health care and promoted the monitoring of health. It is a descriptive case study. The results relate to the support given to employees in training covering the dissemination of information, communication, training and information management in primary health care. This innovative means of communication in public health, with very little cost to the Unified Health System (SUS), allowed for a weekly registering of work processes for teams that worked in 193 primary health care units (APS) using blogs, whose total accesses reached the seven million mark in mid-2015. In the future there is a possibility that distance learning tools could be used to assist in training processes and in the continuing education of professionals in family health teams.

Experimental and CFD investigation of gas phase freeboard combustion

DEFF Research Database (Denmark)

Andersen, Jimmy

Reliable and accurate modeling capabilities for combustion systems are valuable tools for optimization of the combustion process. This work concerns primary precautions for reducing NO emissions, thereby abating the detrimental effects known as “acid rain”, and minimizing cost for flue gas...... treatment. The aim of this project is to provide validation data for Computational Fluid Dynamic (CFD) models relevant for grate firing combustion conditions. CFD modeling is a mathematical tool capable of predicting fluid flow, mixing and chemical reaction with thermal conversion and transport. Prediction......, but under well-defined conditions. Comprehensive experimental data for velocity field, temperatures, and gas composition are obtained from a 50 kW axisymmetric non-swirling natural gas fired combustion setup under two different settings. Ammonia is added to the combustion setup in order to simulate fuel...

Machine tool structures

CERN Document Server

Koenigsberger, F

1970-01-01

Machine Tool Structures, Volume 1 deals with fundamental theories and calculation methods for machine tool structures. Experimental investigations into stiffness are discussed, along with the application of the results to the design of machine tool structures. Topics covered range from static and dynamic stiffness to chatter in metal cutting, stability in machine tools, and deformations of machine tool structures. This volume is divided into three sections and opens with a discussion on stiffness specifications and the effect of stiffness on the behavior of the machine under forced vibration c

FunGeneNet: a web tool to estimate enrichment of functional interactions in experimental gene sets.

Science.gov (United States)

Tiys, Evgeny S; Ivanisenko, Timofey V; Demenkov, Pavel S; Ivanisenko, Vladimir A

2018-02-09

Estimation of functional connectivity in gene sets derived from genome-wide or other biological experiments is one of the essential tasks of bioinformatics. A promising approach for solving this problem is to compare gene networks built using experimental gene sets with random networks. One of the resources that make such an analysis possible is CrossTalkZ, which uses the FunCoup database. However, existing methods, including CrossTalkZ, do not take into account individual types of interactions, such as protein/protein interactions, expression regulation, transport regulation, catalytic reactions, etc., but rather work with generalized types characterizing the existence of any connection between network members. We developed the online tool FunGeneNet, which utilizes the ANDSystem and STRING to reconstruct gene networks using experimental gene sets and to estimate their difference from random networks. To compare the reconstructed networks with random ones, the node permutation algorithm implemented in CrossTalkZ was taken as a basis. To study the FunGeneNet applicability, the functional connectivity analysis of networks constructed for gene sets involved in the Gene Ontology biological processes was conducted. We showed that the method sensitivity exceeds 0.8 at a specificity of 0.95. We found that the significance level of the difference between gene networks of biological processes and random networks is determined by the type of connections considered between objects. At the same time, the highest reliability is achieved for the generalized form of connections that takes into account all the individual types of connections. By taking examples of the thyroid cancer networks and the apoptosis network, it is demonstrated that key participants in these processes are involved in the interactions of those types by which these networks differ from random ones. FunGeneNet is a web tool aimed at proving the functionality of networks in a wide range of sizes of

[The Jena Anxiety Monitoring List (JAMoL) - a tool for the evidence-based treatment of panic disorder with or without agoraphobia in primary care].

Science.gov (United States)

Hiller, Thomas Stephan; Freytag, Antje; Breitbart, Jörg; Teismann, Tobias; Schöne, Elisabeth; Blank, Wolfgang; Schelle, Mercedes; Vollmar, Horst Christian; Margraf, Jürgen; Gensichen, Jochen

2018-04-01

Behavior therapy-oriented methods are recommended for treating anxiety disorders in primary care. The treatment of patients with long-term conditions can be improved by case management and structured clinical monitoring. The present paper describes the rationale, design and application of the 'Jena Anxiety Monitoring List' (JAMoL), a monitoring tool for the treatment of patients with panic disorder, with or without agoraphobia, in primary care. JAMoL's design was based on established clinical measures, the rationale of exposure-based anxiety treatment, and research on family practice-based case management. After piloting, the JAMoL was used in the clinical study 'Jena-PARADISE' (ISRCTN64669297), where non-physician practice staff monitored patients with panic disorder by telephone. Using semi-structured interviews in concomitant studies, study participants were asked about the instrument's functionality. The JAMoL assesses the severity of anxiety symptoms (6 items) as well as the patient's adherence to therapy (4 items) and fosters the case management-related information exchange (3 items). An integrated traffic light scheme facilitates the evaluation of monitoring results. Within the clinical study, non-physician practice staff carried out a total of 1,525 JAMoL-supported monitoring calls on 177 patients from 30 primary care practices (median calls per patient: 10 [interquartile range, 9-10]). Qualitative analyses revealed that most practice teams and patients rated the JAMoL as a practicable and treatment-relevant tool. The JAMoL enables primary care practice teams to continuously monitor anxiety symptoms and treatment adherence in patients with panic disorder with or without agoraphobia. Within the behavior therapy-oriented treatment program 'Jena-PARADISE', the JAMoL constitutes an important case management tool. Copyright © 2018. Published by Elsevier GmbH.

The development of a post occupancy evaluation tool for primary schools: learner comfort assessment tool (LCAT)

CSIR Research Space (South Africa)

Motsatsi, L

2015-12-01

Full Text Available in order to facilitate teaching and learning. The aim of this study was to develop a Post Occupational Evaluation (POE) tool to assess learner comfort in relation to indoor environmental quality in the classroom. The development of POE tool followed a...

Primary culture of glial cells from mouse sympathetic cervical ganglion: a valuable tool for studying glial cell biology.

Science.gov (United States)

de Almeida-Leite, Camila Megale; Arantes, Rosa Maria Esteves

2010-12-15

Central nervous system glial cells as astrocytes and microglia have been investigated in vitro and many intracellular pathways have been clarified upon various stimuli. Peripheral glial cells, however, are not as deeply investigated in vitro despite its importance role in inflammatory and neurodegenerative diseases. Based on our previous experience of culturing neuronal cells, our objective was to standardize and morphologically characterize a primary culture of mouse superior cervical ganglion glial cells in order to obtain a useful tool to study peripheral glial cell biology. Superior cervical ganglia from neonatal C57BL6 mice were enzymatically and mechanically dissociated and cells were plated on diluted Matrigel coated wells in a final concentration of 10,000cells/well. Five to 8 days post plating, glial cell cultures were fixed for morphological and immunocytochemical characterization. Glial cells showed a flat and irregular shape, two or three long cytoplasm processes, and round, oval or long shaped nuclei, with regular outline. Cell proliferation and mitosis were detected both qualitative and quantitatively. Glial cells were able to maintain their phenotype in our culture model including immunoreactivity against glial cell marker GFAP. This is the first description of immunocytochemical characterization of mouse sympathetic cervical ganglion glial cells in primary culture. This work discusses the uses and limitations of our model as a tool to study many aspects of peripheral glial cell biology. Copyright © 2010 Elsevier B.V. All rights reserved.

Determining of the nuclear composition of primary cosmic rays from the experimental distributions of multiple muons in atmospheric showers

International Nuclear Information System (INIS)

Beshtoev, Kh.M.

1993-01-01

Various approaches are discussed for determining the nuclear composition of the primary cosmic radiation from the distributions of multiple muons. Results are presented of calculations of the distributions of multiple muons for A 1 , A 4 , A 14 , A 26 , A 56 nuclei for an infinite plane and for the underground scintillation telescope of the Institute for Nuclear Research of the Academy of Sciences of Russia.The most suitable technique for determination of the primary nuclear composition of cosmic rays from the distribution of multiple muons is shown to be the approximate solution of a set of N equations, in which the respective coefficients of the contributions of various nuclei A i (i=1-N) to the primary composition serve as variables, while the remaining parts of these equations are the distributions of multiple muons obtained experimentally. 7 refs.; 2 tabs

Experimental and analytical combined thermal approach for local tribological understanding in metal cutting

International Nuclear Information System (INIS)

Artozoul, Julien; Lescalier, Christophe; Dudzinski, Daniel

2015-01-01

Metal cutting is a highly complex thermo-mechanical process. The knowledge of temperature in the chip forming zone is essential to understand it. Conventional experimental methods such as thermocouples only provide global information which is incompatible with the high stress and temperature gradients met in the chip forming zone. Field measurements are essential to understand the localized thermo-mechanical problem. An experimental protocol has been developed using advanced infrared imaging in order to measure temperature distribution in both the tool and the chip during an orthogonal or oblique cutting operation. It also provides several information on the chip formation process such as some geometrical characteristics (tool-chip contact length, chip thickness, primary shear angle) and thermo-mechanical information (heat flux dissipated in deformation zone, local interface heat partition ratio). A study is carried out on the effects of cutting conditions i.e. cutting speed, feed and depth of cut on the temperature distribution along the contact zone for an elementary operation. An analytical thermal model has been developed to process experimental data and access more information i.e. local stress or heat flux distribution. - Highlights: • A thermal analytical model is proposed for orthogonal cutting process. • IR thermography is used during cutting tests. • Combined experimental and modeling approaches are applied. • Heat flux and stress distribution at the tool-chip interface are determined. • The decomposition into sticking and sliding zones is defined.

Development of a simple screening tool for opportunistic COPD case finding in primary care in Latin America: The PUMA study.

Science.gov (United States)

López Varela, Maria Victorina; Montes de Oca, Maria; Rey, Alejandra; Casas, Alejandro; Stirbulov, Roberto; Di Boscio, Valentina

2016-10-01

Opportunistic chronic obstructive pulmonary disease (COPD) case finding approaches for high-risk individuals with or without symptoms is a feasible option for disease identification. PUMA is an opportunistic case finding study conducted in primary care setting of Argentina, Colombia, Venezuela and Uruguay. The objectives were to measure COPD prevalence in an at-risk population visiting primary care for any reason, to assess the yield of this opportunistic approach and the accuracy of a score developed to detect COPD. Subjects attending routine primary care visits, ≥40 years of age, current or former smokers or exposed to biomass smoke, completed a questionnaire and performed spirometry. COPD was defined as post-bronchodilator (post-BD) forced expiratory volume in 1 s (FEV1 )/forced vital capacity (FVC) 50 years, heavy smokers (>30 pack-years), with dyspnoea, and having prior spirometry. A simple score and a weighted score constructed using the following predictive factors: gender, age, pack-years smoking, dyspnoea, sputum, cough and spirometry, had a mean accuracy for detecting COPD (post-BD FEV1 /FVC tool to select subjects for spirometry in primary care. © 2016 Asian Pacific Society of Respirology.

Assessment of quality of prescribing in patients of hypertension at primary and secondary health care facilities using the Prescription Quality Index (PQI) tool.

Science.gov (United States)

Suthar, Jalpa Vashishth; Patel, Varsha J

2014-01-01

To determine the quality of prescribing in hypertension in primary and secondary health care settings using the Prescription Quality Index (PQI) tool and to assess the reliability of this tool. An observational cross-sectional study was carried out for 6 months in order to assess quality of prescribing of antihypertensive drugs using Prescription Quality Index (PQI) at four primary (PHC) and two secondary (SHC) health care facilities. Patients attending these facilities for at least 3 months were included. Complete medical history and prescriptions received were noted. Total and criteria wise PQI scores were derived for each prescription. Prescriptions were categorized as poor (score of ≤31), medium (score 32-33) and high quality (score 34-43) based on PQI total score. Psychometric analysis using factor analysis was carried out to assess reliability and validity. Total 73 hypertensive patients were included. Mean age was 61.2 ± 11 years with 35 (48%) patients above 65 years of age. Total PQI score was 26 ± 11. There was a significant difference in PQI score between PHC and SHC (P hypertensive patients was poor, somewhat better in primary as compared to secondary health care facility. PQI is reliable for measuring prescribing quality in hypertension in Indian set up.

An Observation Tool for Comprehensive Pedagogy in Content and Language Integrated Learning (CLIL: Examples from Primary Education

Directory of Open Access Journals (Sweden)

Taina M Wewer

2017-08-01

Full Text Available This article on principles and practices in Content and Language Integrated Learning (CLIL is also applicable for general foreign and second language instruction. Since there is no ‘one size fits all’ CLIL pedagogy, the origin of the article lies in the need of educators to obtain and exchange ideas of and tools for actual classroom practices (Pérez Cañado, 2017, and ensure that all key features of CLIL are present in instruction. Although there are a few handbooks available for launching CLIL and adopting CLIL pedagogy (e.g., Coyle, Hood, & Marsh, 2010; Mehisto, Marsh, & Frigols, 2008, these provide principles and general examples of content-based instruction at higher levels of education rather than more detailed advice on how to operate in the beginning phases with young language learners, hence the focus on primary education. The Observation Tool for Effective CLIL Teaching created by de Graaff, Koopman, Anikina, and Gerrit (2007 was chosen as the starting point and was complemented with three additional fields that were not markedly included in the original model: cultural aspects, affects, and assessment.

SENSITIVITY ANALYSIS OF KINETIC CONSTANTS AS A TOOL FOR ELUCIDATING THE POLYMERIZATION MECHANISM OF ACRYL-FURANIC COMPOUNDS

Directory of Open Access Journals (Sweden)

Jurgen Lange

2013-12-01

Full Text Available By means of the sensitivity analysis of kinetics constants in a proposed mechanism for radical polymerization of acrylfuranic compounds [Furfuryl Acrylate (FA and Methacrylate (FM],it is elucidated which elementary steps are relevant in the phenomenology. In this analysis, the application of Come's methodology allows to classify the elementary steps of a mechanism in three categories: Non-sensible, Non-determinant, Sensible. The results obtained with this tool in modeling of experimental data in free radical polymerization of FA and FM suggest that kinetic mechanism consists mainly on five elementary steps: 1 Primary initiation, 2 propagation, 3 degradative transfers (which include intermolecular and primary, 4 re-initiation and 5 cross-termination. Thus, taking into account these elementary steps in mathematical modeling, the polymerization of FA and FM in different experimental conditions was successfully simulated.

Experimental investigation and optimization of welding process parameters for various steel grades using NN tool and Taguchi method

Science.gov (United States)

Soni, Sourabh Kumar; Thomas, Benedict

2018-04-01

The term "weldability" has been used to describe a wide variety of characteristics when a material is subjected to welding. In our analysis we perform experimental investigation to estimate the tensile strength of welded joint strength and then optimization of welding process parameters by using taguchi method and Artificial Neural Network (ANN) tool in MINITAB and MATLAB software respectively. The study reveals the influence on weldability of steel by varying composition of steel by mechanical characterization. At first we prepare the samples of different grades of steel (EN8, EN 19, EN 24). The samples were welded together by metal inert gas welding process and then tensile testing on Universal testing machine (UTM) was conducted for the same to evaluate the tensile strength of the welded steel specimens. Further comparative study was performed to find the effects of welding parameter on quality of weld strength by employing Taguchi method and Neural Network tool. Finally we concluded that taguchi method and Neural Network Tool is much efficient technique for optimization.

4D Visualization of Experimental Procedures in Rock Physics

Science.gov (United States)

Vanorio, T.; di Bonito, C.

2010-12-01

Engaging students in laboratory classes in geophysics is becoming more and more difficult. This is primarily because of an ever-widening gap between the less appealing aspects that characterize these courses (e.g., lengthiness of the experimental operations, high student/instrument ratio, limited time associated with lack of previous hands-on experiences, and logistical and safety concerns) and the life style of the 21st century generations (i.e., extensive practice to high-tech tools, high-speed communications and computing, 3D graphics and HD videos). To bridge the gap and enhance the teaching strategy of laboratory courses in geophysics, we have created simulator-training tools for use in preparation for the actual experimental phase. We are using a modeling, animation, and rendering package to create (a) 3D models that accurately reproduce actual scenarios and instruments used for the measurement of rock physics properties and (b) 4D interactive animations that simulate hands-on demonstrations of the experimental procedures. We present here a prototype describing step-by-step the experimental protocol and the principles behind the measurement of rock porosity. The tool reproduces an actual helium porosimeter and makes use of interactive animations, guided text, and a narrative voice guiding the audience through the different phases of the experimental process. Our strategy is to make the most of new technologies while preserving the accuracy of classical laboratory methods and practices. These simulations are not intended to replace traditional lab work; rather they provide students with the opportunity for review and repetition. The primary goal is thus to help students familiarize themselves during their earlier curricula with lab methodologies, thus minimizing apparent hesitation and frustration in later classes. This may also increase the level of interest and involvement of undergraduate students and, in turn, enhance their keenness to pursue their

Transformational Tools and Technologies Project

Data.gov (United States)

National Aeronautics and Space Administration — The Transformational Tools and Technologies (TTT) Project advances state-of-the-art computational and experimental tools and technologies that are vital to aviation...

Primary care models for treating opioid use disorders: What actually works? A systematic review.

Directory of Open Access Journals (Sweden)

Pooja Lagisetty

Full Text Available Primary care-based models for Medication-Assisted Treatment (MAT have been shown to reduce mortality for Opioid Use Disorder (OUD and have equivalent efficacy to MAT in specialty substance treatment facilities.The objective of this study is to systematically analyze current evidence-based, primary care OUD MAT interventions and identify program structures and processes associated with improved patient outcomes in order to guide future policy and implementation in primary care settings.PubMed, EMBASE, CINAHL, and PsychInfo.We included randomized controlled or quasi experimental trials and observational studies evaluating OUD treatment in primary care settings treating adult patient populations and assessed structural domains using an established systems engineering framework.We included 35 interventions (10 RCTs and 25 quasi-experimental interventions that all tested MAT, buprenorphine or methadone, in primary care settings across 8 countries. Most included interventions used joint multi-disciplinary (specialty addiction services combined with primary care and coordinated care by physician and non-physician provider delivery models to provide MAT. Despite large variability in reported patient outcomes, processes, and tasks/tools used, similar key design factors arose among successful programs including integrated clinical teams with support staff who were often advanced practice clinicians (nurses and pharmacists as clinical care managers, incorporating patient "agreements," and using home inductions to make treatment more convenient for patients and providers.The findings suggest that multidisciplinary and coordinated care delivery models are an effective strategy to implement OUD treatment and increase MAT access in primary care, but research directly comparing specific structures and processes of care models is still needed.

Development and Application of a Tool for Optimizing Composite Matrix Viscoplastic Material Parameters

Science.gov (United States)

Murthy, Pappu L. N.; Naghipour Ghezeljeh, Paria; Bednarcyk, Brett A.

2018-01-01

This document describes a recently developed analysis tool that enhances the resident capabilities of the Micromechanics Analysis Code with the Generalized Method of Cells (MAC/GMC) and its application. MAC/GMC is a composite material and laminate analysis software package developed at NASA Glenn Research Center. The primary focus of the current effort is to provide a graphical user interface (GUI) capability that helps users optimize highly nonlinear viscoplastic constitutive law parameters by fitting experimentally observed/measured stress-strain responses under various thermo-mechanical conditions for braided composites. The tool has been developed utilizing the MATrix LABoratory (MATLAB) (The Mathworks, Inc., Natick, MA) programming language. Illustrative examples shown are for a specific braided composite system wherein the matrix viscoplastic behavior is represented by a constitutive law described by seven parameters. The tool is general enough to fit any number of experimentally observed stress-strain responses of the material. The number of parameters to be optimized, as well as the importance given to each stress-strain response, are user choice. Three different optimization algorithms are included: (1) Optimization based on gradient method, (2) Genetic algorithm (GA) based optimization and (3) Particle Swarm Optimization (PSO). The user can mix and match the three algorithms. For example, one can start optimization with either 2 or 3 and then use the optimized solution to further fine tune with approach 1. The secondary focus of this paper is to demonstrate the application of this tool to optimize/calibrate parameters for a nonlinear viscoplastic matrix to predict stress-strain curves (for constituent and composite levels) at different rates, temperatures and/or loading conditions utilizing the Generalized Method of Cells. After preliminary validation of the tool through comparison with experimental results, a detailed virtual parametric study is

Experimental and analytical studies for the validation of HTR-VGD and primary cell passive decay heat removal. Supplement. Calculations

International Nuclear Information System (INIS)

Geiss, M.; Giannikos, A.; Hejzlar, P.; Kneer, A.

1993-04-01

The alternative concept for a modular HTR-reactor design by Siempelkamp, Krefeld, using a prestressed cast iron vessel (VGD) combined with a cast iron/concrete module for the primary cell with integrated passive decay heat removal system was fully qualified with respect to operational and accidental thermal loads. The main emphasis was to confirm and validate the passive decay heat removal capability. An experimental facility (INWA) was designed, instrumented and operated with an appropriate electrical heating system simulating steady-state operational and transient accidental thermal loads. The experiments were accompanied by extensive computations concerning the combination of conductive, radiative and convective energy transport mechanisms in the different components of the VGD/primary cell structures, as well as elastic-plastic stress analyses of the VGD. In addition, a spectrum of potential alternatives for passive energy removed options have been parametrically examined. The experimental data clearly demonstrate that the proposed Siempelkamp-design is able to passively and safely remove the decay heat for operational and accidental conditions without invalidating technological important thermal limits. This also holds in case of failures of both the natural convection system and ultimate heat sink by outside concrete water film cooling. (orig./HP) [de

A Tool Measuring Remaining Thickness of Notched Acoustic Cavities in Primary Reaction Control Thruster NDI Standards

Science.gov (United States)

Sun, Yushi; Sun, Changhong; Zhu, Harry; Wincheski, Buzz

2006-01-01

Stress corrosion cracking in the relief radius area of a space shuttle primary reaction control thruster is an issue of concern. The current approach for monitoring of potential crack growth is nondestructive inspection (NDI) of remaining thickness (RT) to the acoustic cavities using an eddy current or remote field eddy current probe. EDM manufacturers have difficulty in providing accurate RT calibration standards. Significant error in the RT values of NDI calibration standards could lead to a mistaken judgment of cracking condition of a thruster under inspection. A tool based on eddy current principle has been developed to measure the RT at each acoustic cavity of a calibration standard in order to validate that the standard meets the sample design criteria.

Tools for Science Inquiry Learning: Tool Affordances, Experimentation Strategies, and Conceptual Understanding

Science.gov (United States)

Bumbacher, Engin; Salehi, Shima; Wieman, Carl; Blikstein, Paulo

2017-12-01

Manipulative environments play a fundamental role in inquiry-based science learning, yet how they impact learning is not fully understood. In a series of two studies, we develop the argument that manipulative environments (MEs) influence the kind of inquiry behaviors students engage in, and that this influence realizes through the affordances of MEs, independent of whether they are physical or virtual. In particular, we examine how MEs shape college students' experimentation strategies and conceptual understanding. In study 1, students engaged in two consecutive inquiry tasks, first on mass and spring systems and then on electric circuits. They either used virtual or physical MEs. We found that the use of experimentation strategies was strongly related to conceptual understanding across tasks, but that students engaged differently in those strategies depending on what ME they used. More students engaged in productive strategies using the virtual ME for electric circuits, and vice versa using the physical ME for mass and spring systems. In study 2, we isolated the affordance of measurement uncertainty by comparing two versions of the same virtual ME for electric circuits—one with and one without noise—and found that the conditions differed in terms of productive experimentation strategies. These findings indicate that measures of inquiry processes may resolve apparent ambiguities and inconsistencies between studies on MEs that are based on learning outcomes alone.

Influence of hydrazine primary water chemistry on corrosion of fuel cladding and primary circuit components

International Nuclear Information System (INIS)

Iourmanov, V.; Pashevich, V.; Bogancs, J.; Tilky, P.; Schunk, J.; Pinter, T.

1999-01-01

Earlier at Paks 1-4 NPP standard ammonia chemistry was in use. The following station performance indicators were improved when hydrazine primary water chemistry was introduced: occupational radiation exposures of personnel; gamma-radiation dose rates near primary system components during refuelling and maintenance outages. The reduction of radiation exposures and radiation fields were achieved without significant expenses. Recent results of experimental studies allowed to explain the mechanism of hydrazine dosing influence on: corrosion rate of structure materials in primary coolant; behaviour of soluble and insoluble corrosion products including long-life corrosion-induced radionuclides in primary system during steady-state and transient operation modes; radiolytic generation of oxidising radiolytic products in core and its corrosion activity in primary system; radiation situation during refuelling and maintenance outages; foreign material degradation and removal (including corrosion active oxidant species) from primary system during abnormal events. Operational experience and experimental data have shown that hydrazine primary water chemistry allows to reduce corrosion wear and thereby makes it possible to extend the life-time of plant components in primary system. (author)

The reliability analysis of cutting tools in the HSM processes

OpenAIRE

W.S. Lin

2008-01-01

Purpose: This article mainly describe the reliability of the cutting tools in the high speed turning by normaldistribution model.Design/methodology/approach: A series of experimental tests have been done to evaluate the reliabilityvariation of the cutting tools. From experimental results, the tool wear distribution and the tool life are determined,and the tool life distribution and the reliability function of cutting tools are derived. Further, the reliability ofcutting tools at anytime for h...

Experimental study of residual stresses in laser clad AISI P20 tool steel on pre-hardened wrought P20 substrate

International Nuclear Information System (INIS)

Chen, J.-Y.; Conlon, K.; Xue, L.; Rogge, R.

2010-01-01

Research highlights: → Laser cladding of P20 tool steel. → Residual stress analysis of laser clad P20 tool steel. → Microstructure of laser clad P20 tool steel. → Tooling Repair using laser cladding. → Stress reliving treatment of laser clad P20 tool steel. - Abstract: Laser cladding is to deposit desired material onto the surface of a base material (or substrate) with a relatively low heat input to form a metallurgically sound and dense clad. This process has been successfully applied for repairing damaged high-value tooling to reduce their through-life cost. However, laser cladding, which needs to melt a small amount of a substrate along with cladding material, inevitably introduces residual stresses in both clad and substrate. The tensile residual stresses in the clad could adversely affect mechanical performance of the substrate being deposited. This paper presents an experimental study on process-induced residual stresses in laser clad AISI P20 tool steel onto pre-hardened wrought P20 base material and the correlation with microstructures using hole-drilling and neutron diffraction methods. Combined with X-ray diffraction and scanning electron microscopic analyses, the roles of solid-state phase transformations in the clad and heat-affected zone (HAZ) of the substrate during cladding and post-cladding heat treatments on the development and controllability of residual stresses in the P20 clad have been investigated, and the results could be beneficial to more effective repair of damaged plastic injection molds made by P20 tool steel.

Establishment of primary cell culture from the temperate symbiotic cnidarian, Anemonia viridis.

Science.gov (United States)

Barnay-Verdier, Stéphanie; Dall'osso, Diane; Joli, Nathalie; Olivré, Juliette; Priouzeau, Fabrice; Zamoum, Thamilla; Merle, Pierre-Laurent; Furla, Paola

2013-10-01

The temperate symbiotic sea anemone Anemonia viridis, a member of the Cnidaria phylum, is a relevant experimental model to investigate the molecular and cellular events involved in the preservation or in the rupture of the symbiosis between the animal cells and their symbiotic microalgae, commonly named zooxanthellae. In order to increase research tools for this model, we developed a primary culture from A. viridis animal cells. By adapting enzymatic dissociation protocols, we isolated animal host cells from a whole tentacle in regeneration state. Each plating resulted in a heterogeneous primary culture consisted of free zooxanthellae and many regular, small rounded and adherent cells (of 3-5 μm diameter). Molecular analyses conducted on primary cultures, maintained for 2 weeks, confirmed a specific signature of A. viridis cells. Further serial dilutions and micromanipulation allowed us to obtain homogenous primary cultures of the small rounded cells, corresponding to A. viridis "epithelial-like cells". The maintenance and the propagation over a 4 weeks period of primary cells provide, for in vitro cnidarian studies, a preliminary step for further investigations on cnidarian cellular pathways notably in regard to symbiosis interactions.

3D Finite Element Modelling of Drilling Process of Al2024-T3 Alloy with solid tooling and Experimental Validation

DEFF Research Database (Denmark)

Davoudinejad, Ali; Tosello, Guido

2017-01-01

Drilling is an indispensable process for many manufacturing industries due to the importance of the process for assembling components. This study presents a 3D finite element modeling (3D FEM) approach for drilling process of aluminum 2024-T3. The 3D model of tool for two facet HSSCo and four facet...... area were determined numerically. The results confirm the ability and advantage of 3D FE model of the drilling process....... HSS were generated base on the details geometry. The simulations were carried out for both drills in different cutting conditions. The numerically obtained thrust forces were compared against experimental results. The tool stress distribution, chip formation and temperature distribution in the chip...

The relationships between ceramic tool life and different machining parameters

International Nuclear Information System (INIS)

El-Axir, M.H.; El-Masry, A.A.; Mashal, Y.A.H.

2001-01-01

With the increasing use of ceramic tool materials in applications, has come an increasing need for experimental data to assign the behavior of the life of these tool materials. Experimental results during turning operation show that it is possible to increase cutting tool life substantially by a proper variation of the cutting parameters used in this work. The tool lives (tool flank wear land length) of three different ceramic materials, namely; Silicon carbide (SiC), Alumina (Al/sub 2/O/sub 3/) and partially stabilized zirconia (PSZ) in addition to, Titanium carbide and high speed steel tools are investigated in this work. Also, The effect of varying the cutting speed, feed rate and tool rake angle on tool life of each tool material is studied. The experimental work was carried out utilizing one of the experimental design techniques based on response surface methodology. It was found that the SiC cutting tool showed the highest tool life among all materials tested in this work. It was also noticed that increasing the cutting speed has led to an increase in tool life for ceramic tools only. However, increasing the feed rate and tool rake angle resulted in a reduction in tool life in all materials examined in the present study. Further analysis conducted on SiC tool material to examine the effect of the interaction of cutting parameters on the tool life. (author)

Tool steels

DEFF Research Database (Denmark)

Højerslev, C.

2001-01-01

On designing a tool steel, its composition and heat treatment parameters are chosen to provide a hardened and tempered martensitic matrix in which carbides are evenly distributed. In this condition the matrix has an optimum combination of hardness andtoughness, the primary carbides provide...... resistance against abrasive wear and secondary carbides (if any) increase the resistance against plastic deformation. Tool steels are alloyed with carbide forming elements (Typically: vanadium, tungsten, molybdenumand chromium) furthermore some steel types contains cobalt. Addition of alloying elements...... serves primarily two purpose (i) to improve the hardenabillity and (ii) to provide harder and thermally more stable carbides than cementite. Assuming proper heattreatment, the properties of a tool steel depends on the which alloying elements are added and their respective concentrations....

Early detection and prevention of domestic violence using the Women Abuse Screening Tool (WAST) in primary health care clinics in Malaysia.

Science.gov (United States)

Yut-Lin, Wong; Othman, Sajaratulnisah

2008-01-01

Despite being an emergent major public health problem, little research has been done on domestic violence from the perspectives of early detection and prevention. Thus, this cross-sectional study was conducted to identify domestic violence among female adult patients attending health centers at the primary care level and to determine the relationship between social correlates of adult patients and domestic violence screening and subsequent help/health-seeking behavior if abused. Face-to-face interviews were conducted with 710 female adult patients from 8 health centers in Selangor who matched the inclusion criteria and consented to participate in the study, using a structured questionnaire that included adaptation of a validated 8-item Women Abuse Screening Tool (WAST). Statistical tests showed significant differences in ethnicity, income, and education between those screened positive and those screened negative for domestic violence. Of the participants, 92.4% reported that during consultations, doctors had never asked them whether they were abused by their husband/partner. Yet, 67.3% said they would voluntarily tell the doctor if they were abused by their husband/partner. The findings indicate that primary care has an important role in identifying domestic violence by applying the WAST screening tool, or an appropriate adaptation, with women patients during routine visits to the various health centers. Such assessment for abuse could be secondary prevention for the abused women, but more important, it will serve as primary prevention for nonabused women. This approach not only will complement the existing 1-stop crisis center policy by the Ministry of Health that copes with crisis intervention but also will spearhead efforts toward prevention of domestic violence in Malaysia.

An experimental study on the primary fragmentation and attrition of limestones in a fluidized bed

International Nuclear Information System (INIS)

Yao, Xuan; Zhang, Hai; Yang, Hairui; Liu, Qing; Wang, Jinwei; Yue, Guangxi

2010-01-01

In this paper, an experimental study on the primary fragmentation and attrition of 5 limestones in a fluidized bed was conducted. The intensity of fragmentation and attrition were measured in the same apparatus but at different fluidizing velocities. It was found that the averaged size of the particles decreased by about 10-20% during the fragmentation process. The important factors for particle comminution include limestone types, heating rate, calcination condition and ambient CO 2 concentration. Fragmentation mainly occurred in the first a few minutes in the fluidized bed and it was more intense than that in the muffle furnace at the same temperature. The original size effect was ambiguous, depending on the limestone type. The comminution caused by attrition mainly occurred during calcination process rather than sulphation process. The sulphation process was fragmentation and attrition resisted. The attrition rate of sulphate was similar to that of lime in trend, decaying exponentially with time, but was one-magnitude-order smaller than that of lime. Present experimental results indicate that fragmentation mechanism of the limestone is dominated by CO 2 release instead of thermal stress. (author)

To grip or not to grip: An experimental approach for understanding the use of prehensile areas in mousterian tools

OpenAIRE

Baena Preysler, Javier; Torres Navas, Concepción; Pérez Díaz, Sara; Bustos-Pérez, Guillermo; Romagnoli, Francesca

2016-01-01

The existence of a more or less complex handling technology with the lithic tools during the Lower and Middle Paleolithic is an interesting topic for understanding aspects of the human behavior during these periods. In this work we present a preliminary experimental evaluation of the possible functionality of prehensile area in some of the most representative lithic types of the Mousterian assemblages (dorsal elements and levallois chapeau de gendarme proximal area), in which t...

Theoretical and experimental studies on bellows type expansion joints behaviour of Chinon 3 primary coolant system

International Nuclear Information System (INIS)

Vrillon, B.; Jeanpierre, F.; Copin, A.; Gregoire, J.P.

1975-01-01

The vibration study of the bellows was performed in two stages. A series of vibration tests was performed on a real bellow joint. By comparing the experimental results with calculations using the finite elements method for revolution shells it was possible to qualify the representation of the waves and reinforcement rings. The resonant frequencies and modes were calculated for the various joints under reactor conditions. According to the excitation sources considered, the amplitude of the displacements and stresses can be determined from these characteristic modes. The corrugations are protected internally from the aerodynamic effects of the gas flow by an inner sleeve welded to the primary piping upstream and free downstream. The annular space between this sleeve and the corrugations forms a resonant volume liable to be excited by flow-induced pressure fluctuations. It was possible to calculate the characteristic resonance frequencies and modes of this gas column (air at normal temperature and pressure). A full-scale mock-up test under conditions corresponding to the calculation hypotheses gave experimental proof of the calculation results. Owing to the good correlation between the results of these two studies an attempt was made to calculate the acoustical behaviour of these cavities for nominal running conditions (temperature and pressure) as a function of the known excitation sources. The results obtained from all these tests show that the use of bellows type expansion joints on a primary reactor circuit offers the same guarantees of reliability and resistance as any other circuit component under pressure, as long as the strains they undergo remain within the limits specified by the regulations and nuclear codifications

Comparison of Numerically Simulated and Experimentally Measured Performance of a Rotating Detonation Engine

Science.gov (United States)

Paxson, Daniel E.; Fotia, Matthew L.; Hoke, John; Schauer, Fred

2015-01-01

A quasi-two-dimensional, computational fluid dynamic (CFD) simulation of a rotating detonation engine (RDE) is described. The simulation operates in the detonation frame of reference and utilizes a relatively coarse grid such that only the essential primary flow field structure is captured. This construction and other simplifications yield rapidly converging, steady solutions. Viscous effects, and heat transfer effects are modeled using source terms. The effects of potential inlet flow reversals are modeled using boundary conditions. Results from the simulation are compared to measured data from an experimental RDE rig with a converging-diverging nozzle added. The comparison is favorable for the two operating points examined. The utility of the code as a performance optimization tool and a diagnostic tool are discussed.

Combined numerical and experimental determination of the convective heat transfer coefficient between an AlCrN-coated Vanadis 4 tool and Rhenus oil

DEFF Research Database (Denmark)

Üstünyagiz, Esmeray; Nielsen, Chris V.; Tiedje, Niels S.

2018-01-01

Abstract Regardless of the field of application, the reliability of numerical simulations depends on correct description of boundary conditions. In thermal simulation, determination of heat transfer coefficients is important because it varies with material properties and process conditions....... This paper shows a combined experimental and numerical analysis applied for determination of the heat transfer coefficient between an AlCrN-coated Vanadis 4 tool and Rhenus LA722086 oil in an unloaded condition, i.e. without the tool being in contact with a workpiece. It is found that the heat transfer...... coefficient in unloaded conditions at 80°C oil temperature is 0.1 kW/(m2∙K) between the selected stamping tool and mineral oil. A sensitivity analysis of the numerical model was performed to verify the effects of mesh discretization, temperature measurement location and tool geometry. Among these parameters...

GIS as a Tool for Education Decision Support System: A Demonstration with Public Primary Schools in Zaria City Kaduna State Nigeria

Directory of Open Access Journals (Sweden)

U. Wali

2015-07-01

Full Text Available This paper aimed at demonstrating the use of GIS in the display of data about primary schools in the walled part of Zaria city, Kaduna State. It is hoped that the database and its graphic display in maps will guide decision making at the primary education level in the study area. Coordinates of the schools were obtained with a handheld GPS receiver, while their attribute data were obtained from the local education authority and triangulated with questionnaires administered to the headmasters of the schools. ArcGIS 9.2 version software was used for buffer zone (1 km. The result indicates that there are 31 public primary schools in the study area. The oldest was established in 1921 and the latest in 2007. Graphic displays of some attributes of the schools were produced. The buffer zones produced suggest no pupil walks more than a kilometer to reach school. It is recommended that in the future, GIS tools should be applied when managing school data. Capacities to achieve this should be developed.

The Electronic Patient Reported Outcome Tool: Testing Usability and Feasibility of a Mobile App and Portal to Support Care for Patients With Complex Chronic Disease and Disability in Primary Care Settings

Science.gov (United States)

Gill, Ashlinder; Khan, Anum Irfan; Hans, Parminder Kaur; Kuluski, Kerry; Cott, Cheryl

2016-01-01

Background People experiencing complex chronic disease and disability (CCDD) face some of the greatest challenges of any patient population. Primary care providers find it difficult to manage multiple discordant conditions and symptoms and often complex social challenges experienced by these patients. The electronic Patient Reported Outcome (ePRO) tool is designed to overcome some of these challenges by supporting goal-oriented primary care delivery. Using the tool, patients and providers collaboratively develop health care goals on a portal linked to a mobile device to help patients and providers track progress between visits. Objectives This study tested the usability and feasibility of adopting the ePRO tool into a single interdisciplinary primary health care practice in Toronto, Canada. The Fit between Individuals, Fask, and Technology (FITT) framework was used to guide our assessment and explore whether the ePRO tool is: (1) feasible for adoption in interdisciplinary primary health care practices and (2) usable from both the patient and provider perspectives. This usability pilot is part of a broader user-centered design development strategy. Methods A 4-week pilot study was conducted in which patients and providers used the ePRO tool to develop health-related goals, which patients then monitored using a mobile device. Patients and providers collaboratively set goals using the system during an initial visit and had at least 1 follow-up visit at the end of the pilot to discuss progress. Focus groups and interviews were conducted with patients and providers to capture usability and feasibility measures. Data from the ePRO system were extracted to provide information regarding tool usage. Results Six providers and 11 patients participated in the study; 3 patients dropped out mainly owing to health issues. The remaining 8 patients completed 210 monitoring protocols, equal to over 1300 questions, with patients often answering questions daily. Providers and patients

Experimental and Theoretical Mechanistic Investigation of the Iridium-Catalyzed Dehydrogenative Decarbonylation of Primary Alcohols

DEFF Research Database (Denmark)

Olsen, Esben Paul Krogh; Singh, Thishana; Harris, Pernille

2015-01-01

The mechanism for the iridium-BINAP catalyzed dehydrogenative decarbonylation of primary alcohols with the liberation of molecular hydrogen and carbon monoxide was studied experimentally and computationally. The reaction takes place by tandem catalysis through two catalytic cycles involving...... cycles. One carbon monoxide ligand was shown to remain coordinated to iridium throughout the reaction, and release of carbon monoxide was suggested to occur from a dicarbonyl complex. IrH2Cl(CO)(rac-BINAP) was also synthesized and detected in the dehydrogenation of benzyl alcohol. In the same experiment......, IrHCl2(CO)(rac-BINAP) was detected from the release of HCl in the dehydrogenation and subsequent reaction with IrCl(CO)(rac-BINAP). This indicated a substitution of chloride with the alcohol to form a square planar iridium alkoxo complex that could undergo a beta-hydride elimination. A KIE of 1...

Engineering tools for interior tyre tread pattern noise

NARCIS (Netherlands)

Bekke, Dirk

2014-01-01

The regular tyre tread pattern design process is often based upon experience and experimental evaluations and may take about 2 years. The use of engineering tooling could improve and speed up this process. The research objective is therefore to develop experimental and simulation tooling by which

Patients' Illness Perception as a Tool to Improve Individual Disease Management in Primary Cutaneous Lymphomas.

Science.gov (United States)

Porkert, Stefanie; Lehner-Baumgartner, Eva; Valencak, Julia; Knobler, Robert; Riedl, Elisabeth; Jonak, Constanze

2018-02-07

The Revised Illness Perception Questionnaire (IPQ-R) has been shown to assess illness perception reproducibly in primary cutaneous T-cell lymphomas (CTCL). Illness perception reflects patients' individual concepts of understanding and interpretation of the disease, influencing illness behaviour and health-related quality of life (HRQOL). This study investigated the clinical relevance of the relationships between illness perception, illness behaviour, and HRQOL in CTCL and cutaneous B-cell lymphomas (CBCL). A total of 92 patients completed the IPQ-R, the Scale for the Assessment of Illness Behavior (SAIB), and a skin-specific HRQOL tool (Skindex-29). Data on illness behaviour were not evidently related to illness perception, whereas illness perception was significantly associated with HRQOL. Both, IPQ-R and HRQOL results correlated with disease entity, stage, and socio-demographics. Only IPQ-R results provided practical information on patients' needs to train personal coping strategies. IPQ-R assessment in CTCL and CBCL might be a useful instrument to improve individual disease management.

The effects of hydroxyapatite coating and bone allograft on fixation of loaded experimental primary and revision implants

DEFF Research Database (Denmark)

Søballe, Kjeld; Mouzin, Olivier R G; Kidder, Louis A

2003-01-01

We used our established experimental model of revision joint replacement to examine the roles of hydroxyapatite coating and bone graft in improving the fixation of revision implants. The revision protocol uses the Søballe micromotion device in a preliminary 8-week period of implant instability...... a titanium alloy (Ti) or a hydroxyapatite (HA) 6.0 mm plasma-sprayed implant, in the presence or absence of allograft packed into the initial 0.75 mm peri-implant gap. The contralateral limb is subjected to primary surgery with the same implant configuration, and serves as control. 8 implants were included...

The development of a mobile monitoring and feedback tool to stimulate physical activity of people with a chronic disease in primary care: a user-centered design.

Science.gov (United States)

van der Weegen, Sanne; Verwey, Renée; Spreeuwenberg, Marieke; Tange, Huibert; van der Weijden, Trudy; de Witte, Luc

2013-07-02

Physical activity is an important aspect in the treatment of patients with chronic obstructive pulmonary disease or type-2 diabetes. A monitoring and feedback tool combined with guidance by a primary care provider might be a successful method to enhance the level of physical activity in these patients. As a prerequisite for useful technology, it is important to involve the end-users in the design process from an early stage. The aim of this study was to investigate the user requirements for a tool to stimulate physical activity, embedded in primary care practice. The leading principle of this tool is to change behavior by self-monitoring, goal-setting, and feedback. The research team collected qualitative data among 15 patients, 16 care professionals, and several experts. A prototype was developed in three stages. In stage 1, the literature was searched to identify end-users and context. In stage 2, the literature, experts and patient representatives were consulted to set up a use case with the general idea of the innovation. In stage 3, individual interviews and focus groups were held to identify the end-user requirements. Based on these requirements a prototype was built by the engineering team. The development process has led to a tool that generally meets the requirements of the end-users. A tri-axial activity sensor, worn on the hip, is connected by Bluetooth to a smartphone. In an app, quantitative feedback is given about the amount of activity and goals reached by means of graphical visualization, and an image shows a sun when the goal is reached. Overviews about activity per half an hour, per day, week, and month are provided. In the menu of the app and on a secured website, patients can enter information in individual sessions or read feedback messages generated by the system. The practice nurse can see the results of all patients on a secure webpage and can then discuss the results and set personalized goals in consultation with the patient. This study

LITERATURE IN INDIGENOUS LANGUAGES AS ESSENTIAL TOOL ...

African Journals Online (AJOL)

NGOZI

TOOL FOR CHILD DEVELOPMENT AND NATION. BUILDING: THE ... orientation for primary school teachers who fail to attach importance to the teaching of ... right from primary level of education will have positive influence in the lives of.

Developing Seventh Grade Students' Understanding of Complex Environmental Problems with Systems Tools and Representations: a Quasi-experimental Study

Science.gov (United States)

Doganca Kucuk, Zerrin; Saysel, Ali Kerem

2017-03-01

A systems-based classroom intervention on environmental education was designed for seventh grade students; the results were evaluated to see its impact on the development of systems thinking skills and standard science achievement and whether the systems approach is a more effective way to teach environmental issues that are dynamic and complex. A quasi-experimental methodology was used to compare performances of the participants in various dimensions, including systems thinking skills, competence in dynamic environmental problem solving and success in science achievement tests. The same pre-, post- and delayed tests were used with both the comparison and experimental groups in the same public middle school in Istanbul. Classroom activities designed for the comparison group (N = 20) followed the directives of the Science and Technology Curriculum, while the experimental group (N = 22) covered the same subject matter through activities benefiting from systems tools and representations such as behaviour over time graphs, causal loop diagrams, stock-flow structures and hands-on dynamic modelling. After a one-month systems-based instruction, the experimental group demonstrated significantly better systems thinking and dynamic environmental problem solving skills. Achievement in dynamic problem solving was found to be relatively stable over time. However, standard science achievement did not improve at all. This paper focuses on the quantitative analysis of the results, the weaknesses of the curriculum and educational implications.

Development and Experimental Validation of a TRNSYS Dynamic Tool for Design and Energy Optimization of Ground Source Heat Pump Systems

Directory of Open Access Journals (Sweden)

Félix Ruiz-Calvo

2017-09-01

Full Text Available Ground source heat pump (GSHP systems stand for an efficient technology for renewable heating and cooling in buildings. To optimize not only the design but also the operation of the system, a complete dynamic model becomes a highly useful tool, since it allows testing any design modifications and different optimization strategies without actually implementing them at the experimental facility. Usually, this type of systems presents strong dynamic operating conditions. Therefore, the model should be able to predict not only the steady-state behavior of the system but also the short-term response. This paper presents a complete GSHP system model based on an experimental facility, located at Universitat Politècnica de València. The installation was constructed in the framework of a European collaborative project with title GeoCool. The model, developed in TRNSYS, has been validated against experimental data, and it accurately predicts both the short- and long-term behavior of the system.

Cross-cultural adaptation of the US consumer form of the short Primary Care Assessment Tool (PCAT): the Korean consumer form of the short PCAT (KC PCAT) and the Korean standard form of the short PCAT (KS PCAT).

Science.gov (United States)

Jeon, Ki-Yeob

2011-01-01

It is well known that countries with well-structured primary care have better health outcomes, better health equity and reduced healthcare costs. This study aimed to culturally modify and validate the US consumer form of the short Primary Care Assessment Tool (PCAT) in primary care in the Republic of Korea (hereafter referred to as Korea). The Korean consumer form of the short PCAT (KC PCAT) was cross-culturally modified from the original version using a standardised transcultural adaptation method. A pre-test version of the KC PCAT was formulated by replacement of four items and modification of a further four items from the 37 items of the original consumer form of the short PCAT at face value evaluation meetings. Pilot testing was done with a convenience sample of 15 responders at two different sites. Test-retest showed high reliability. To validate the KC PCAT, 606 clients participated in a survey carried out in Korea between February and May 2006. Internal consistency reliability, test-retest reliability and factor analysis were conducted in order to test validity. Psychometric testing was carried out on 37 items of the KC PCAT to make the KS PCAT which has 30 items and has seven principal domains: first contact utilisation, first contact accessibility, ongoing accountable care (ongoing care and coordinated rapport care), integrated care (patient-centred care with integration between primary and specialty care or between different specialties), comprehensive care, community-oriented care and culturally-oriented care. Component factors of the verified KS PCAT explained 58.28% of the total variance in the total item scores of primary care. The verified KS PCAT has been characterised by the seven classic domains of primary care with minor modifications. This may provide clues concerning differences in expectations for primary care in the Korean population as compared with that of the US. The KS PCAT is a reliable and valid tool for the evaluation of the quality of

Final Report, DOE Early Career Award: Predictive modeling of complex physical systems: new tools for statistical inference, uncertainty quantification, and experimental design

Energy Technology Data Exchange (ETDEWEB)

Marzouk, Youssef [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

2016-08-31

Predictive simulation of complex physical systems increasingly rests on the interplay of experimental observations with computational models. Key inputs, parameters, or structural aspects of models may be incomplete or unknown, and must be developed from indirect and limited observations. At the same time, quantified uncertainties are needed to qualify computational predictions in the support of design and decision-making. In this context, Bayesian statistics provides a foundation for inference from noisy and limited data, but at prohibitive computional expense. This project intends to make rigorous predictive modeling *feasible* in complex physical systems, via accelerated and scalable tools for uncertainty quantification, Bayesian inference, and experimental design. Specific objectives are as follows: 1. Develop adaptive posterior approximations and dimensionality reduction approaches for Bayesian inference in high-dimensional nonlinear systems. 2. Extend accelerated Bayesian methodologies to large-scale {\\em sequential} data assimilation, fully treating nonlinear models and non-Gaussian state and parameter distributions. 3. Devise efficient surrogate-based methods for Bayesian model selection and the learning of model structure. 4. Develop scalable simulation/optimization approaches to nonlinear Bayesian experimental design, for both parameter inference and model selection. 5. Demonstrate these inferential tools on chemical kinetic models in reacting flow, constructing and refining thermochemical and electrochemical models from limited data. Demonstrate Bayesian filtering on canonical stochastic PDEs and in the dynamic estimation of inhomogeneous subsurface properties and flow fields.

Experimental anti-GBM nephritis as an analytical tool for studying spontaneous lupus nephritis.

Science.gov (United States)

Du, Yong; Fu, Yuyang; Mohan, Chandra

2008-01-01

Systemic lupus erythematosus (SLE) is an autoimmune disease that results in immune-mediated damage to multiple organs. Among these, kidney involvement is the most common and fatal. Spontaneous lupus nephritis (SLN) in mouse models has provided valuable insights into the underlying mechanisms of human lupus nephritis. However, SLN in mouse models takes 6-12 months to manifest; hence there is clearly the need for a mouse model that can be used to unveil the pathogenic processes that lead to immune nephritis over a shorter time frame. In this article more than 25 different molecules are reviewed that have been studied both in the anti-glomerular basement membrane (anti-GBM) model and in SLN and it was found that these molecules influence both diseases in a parallel fashion, suggesting that the two disease settings share common molecular mechanisms. Based on these observations, the authors believe the experimental anti-GBM disease model might be one of the best tools currently available for uncovering the downstream molecular mechanisms leading to SLN.

Educational Outreach with an Integrated Clinical Tool for Nurse-Led Non-communicable Chronic Disease Management in Primary Care in South Africa: A Pragmatic Cluster Randomised Controlled Trial.

Science.gov (United States)

Fairall, Lara R; Folb, Naomi; Timmerman, Venessa; Lombard, Carl; Steyn, Krisela; Bachmann, Max O; Bateman, Eric D; Lund, Crick; Cornick, Ruth; Faris, Gill; Gaziano, Thomas; Georgeu-Pepper, Daniella; Zwarenstein, Merrick; Levitt, Naomi S

2016-11-01

In many low-income countries, care for patients with non-communicable diseases (NCDs) and mental health conditions is provided by nurses. The benefits of nurse substitution and supplementation in NCD care in high-income settings are well recognised, but evidence from low- and middle-income countries is limited. Primary Care 101 (PC101) is a programme designed to support and expand nurses' role in NCD care, comprising educational outreach to nurses and a clinical management tool with enhanced prescribing provisions. We evaluated the effect of the programme on primary care nurses' capacity to manage NCDs. In a cluster randomised controlled trial design, 38 public sector primary care clinics in the Western Cape Province, South Africa, were randomised. Nurses in the intervention clinics were trained to use the PC101 management tool during educational outreach sessions delivered by health department trainers and were authorised to prescribe an expanded range of drugs for several NCDs. Control clinics continued use of the Practical Approach to Lung Health and HIV/AIDS in South Africa (PALSA PLUS) management tool and usual training. Patients attending these clinics with one or more of hypertension (3,227), diabetes (1,842), chronic respiratory disease (1,157) or who screened positive for depression (2,466), totalling 4,393 patients, were enrolled between 28 March 2011 and 10 November 2011. Primary outcomes were treatment intensification in the hypertension, diabetes, and chronic respiratory disease cohorts, defined as the proportion of patients in whom treatment was escalated during follow-up over 14 mo, and case detection in the depression cohort. Primary outcome data were analysed for 2,110 (97%) intervention and 2,170 (97%) control group patients. Treatment intensification rates in intervention clinics were not superior to those in the control clinics (hypertension: 44% in the intervention group versus 40% in the control group, risk ratio [RR] 1.08 [95% CI 0.94 to 1

Comparative Investigation on Tool Wear during End Milling of AISI H13 Steel with Different Tool Path Strategies

Science.gov (United States)

Adesta, Erry Yulian T.; Riza, Muhammad; Avicena

2018-03-01

Tool wear prediction plays a significant role in machining industry for proper planning and control machining parameters and optimization of cutting conditions. This paper aims to investigate the effect of tool path strategies that are contour-in and zigzag tool path strategies applied on tool wear during pocket milling process. The experiments were carried out on CNC vertical machining centre by involving PVD coated carbide inserts. Cutting speed, feed rate and depth of cut were set to vary. In an experiment with three factors at three levels, Response Surface Method (RSM) design of experiment with a standard called Central Composite Design (CCD) was employed. Results obtained indicate that tool wear increases significantly at higher range of feed per tooth compared to cutting speed and depth of cut. This result of this experimental work is then proven statistically by developing empirical model. The prediction model for the response variable of tool wear for contour-in strategy developed in this research shows a good agreement with experimental work.

The effects of hydroxyapatite coating and bone allograft on fixation of loaded experimental primary and revision implants.

Science.gov (United States)

Søballe, Kjeld; Mouzin, Olivier R G; Kidder, Louis A; Overgaard, Søren; Bechtold, Joan E

2003-06-01

We used our established experimental model of revision joint replacement to examine the roles of hydroxyapatite coating and bone graft in improving the fixation of revision implants. The revision protocol uses the Søballe micromotion device in a preliminary 8-week period of implant instability for the presence of particulate polyethylene. During this procedure, a sclerotic endosteal bone rim forms, and a dense fibrous membrane is engendered, having macrophages with ingested polyethylene and high levels of inflammatory cytokines. At the time of revision after 8 weeks, the cavity is revised with either a titanium alloy (Ti) or a hydroxyapatite (HA) 6.0 mm plasma-sprayed implant, in the presence or absence of allograft packed into the initial 0.75 mm peri-implant gap. The contralateral limb is subjected to primary surgery with the same implant configuration, and serves as control. 8 implants were included in each of the 8 treatment groups (total 64 implants in 32 dogs). The observation period was 4 weeks after revision. Outcome measures are based on histomorphometry and mechanical pushout properties. The revision setting was always inferior to its primary counterpart. Bone graft improved the revision fixation in all treatment groups, as also did the HA coating. The sole exception was revision-grafted HA implants, which reached the same fixation as primary Ti and HA grafted implants. The revision, which was less active in general, seems to need the dual stimulation of bone graft and HA implant surface, to obtain the same level of fixation associated with primary implants. Our findings suggest that the combination of HA implant and bone graft may be of benefit in the clinical revision implant setting.

Cardiovascular Risk in Primary Hyperaldosteronism

NARCIS (Netherlands)

Prejbisz, A.; Warchol-Celinska, E.; Lenders, J.W.M.; Januszewicz, A.

2015-01-01

After the first cases of primary aldosteronism were described and characterized by Conn, a substantial body of experimental and clinical evidence about the long-term effects of excess aldosterone on the cardiovascular system was gathered over the last 5 decades. The prevalence of primary

Risk communication concerning welding fumes for the primary preventive care of welding apprentices in southern Brazil.

Science.gov (United States)

Cezar-Vaz, Marta Regina; Bonow, Clarice Alves; Vaz, Joana Cezar

2015-01-19

This study's aim was to assess the perceptions of welding apprentices concerning welding fumes being associated with respiratory and cardiovascular disorders and assess the implementation of risk communication as a primary prevention tool in the welding training process. This quasi-experimental, non-randomized study with before-and-after design was conducted with 84 welding apprentices in Southern Brazil. Poisson Regression analysis was used. Relative Risk was the measure used with a 95% confidence interval and 5% (p ≤ 0.05) significance level. Significant association was found between perceptions of worsened symptoms of respiratory disorders caused by welding fumes and educational level (p = 0.049), the use of goggles to protect against ultraviolet rays (p = 0.023), and access to services in private health facilities without insurance coverage (p = 0.001). Apprentices younger than 25 years old were 4.9 times more likely to perceive worsened cardiovascular symptoms caused by welding fumes after risk communication (RR = 4.91; CI 95%: 1.09 to 22.2). The conclusion is that risk communication as a primary preventive measure in continuing education processes implemented among apprentices, who are future welders, was efficacious. Thus, this study confirms that risk communication can be implemented as a primary prevention tool in welding apprenticeships.

Evaluation of bone loss due to primary occlusal trauma in two experimental models of occlusal overload

Directory of Open Access Journals (Sweden)

Ana Cristina Távora de Albuquerque LOPES

Full Text Available Abstract Introduction Primary occlusal trauma (OT is an injury of the periodontium with normal height as a result of occlusal forces which exceed their adaptive capacity. Objective To evaluate, histometrically, the alveolar bone loss in the furcation region of rats experimentally submitted to 2 models of occlusal overload. Material and method 45 animals randomly divided into 3 groups: Occlusal Interference (OI, n = 15 - fixing an orthodontic wire segment on the occlusal surface of the first lower molar; Occlusal Overload (OO, n = 15 - wearing of the cusps of the lower contralateral molars, the second and third molars next to the first molar that had its dimensions maintained; Negative Control (NC, n = 15 - evaluation of the initial dimensions of the periodontal ligament (PL. Five animals / group were sacrificed after 14, 21 and 28 days. Result Intergroup evaluation showed significant bone loss in OI (p0.05. The thickness of the PL remained stable in NC (p>0.05. Conclusion OI and OO were effective in the experimental reproduction of OT, and OI promoted greater alveolar bone loss compared to OO, showing that the impact of occlusal overload in OI increased the extent of the OT injury.

Numerical modelling of tool wear in turning with cemented carbide cutting tools

Science.gov (United States)

Franco, P.; Estrems, M.; Faura, F.

2007-04-01

A numerical model is proposed for analysing the flank and crater wear resulting from the loss of material on cutting tool surface in turning processes due to wear mechanisms of adhesion, abrasion and fracture. By means of this model, the material loss along cutting tool surface can be analysed, and the worn surface shape during the workpiece machining can be determined. The proposed model analyses the gradual degradation of cutting tool during turning operation, and tool wear can be estimated as a function of cutting time. Wear-land width (VB) and crater depth (KT) can be obtained for description of material loss on cutting tool surface, and the effects of the distinct wear mechanisms on surface shape can be studied. The parameters required for the tool wear model are obtained from bibliography and experimental observation for AISI 4340 steel turning with WC-Co cutting tools.

Numerical modelling of tool wear in turning with cemented carbide cutting tools

International Nuclear Information System (INIS)

Franco, P.; Estrems, M.; Faura, F.

2007-01-01

A numerical model is proposed for analysing the flank and crater wear resulting from the loss of material on cutting tool surface in turning processes due to wear mechanisms of adhesion, abrasion and fracture. By means of this model, the material loss along cutting tool surface can be analysed, and the worn surface shape during the workpiece machining can be determined. The proposed model analyses the gradual degradation of cutting tool during turning operation, and tool wear can be estimated as a function of cutting time. Wear-land width (VB) and crater depth (KT) can be obtained for description of material loss on cutting tool surface, and the effects of the distinct wear mechanisms on surface shape can be studied. The parameters required for the tool wear model are obtained from bibliography and experimental observation for AISI 4340 steel turning with WC-Co cutting tools

Economic impact of primary open-angle glaucoma in Australia.

Science.gov (United States)

Dirani, Mohamed; Crowston, Jonathan G; Taylor, Penny S; Moore, Peter T; Rogers, Sophie; Pezzullo, M Lynne; Keeffe, Jill E; Taylor, Hugh R

2011-01-01

Glaucoma is the World's leading cause of irreversible blindness, and poses serious public health and economic concerns.   Review. Published randomized trials and population-based studies since 1985. We report the economic impact of primary open-angle glaucoma and model the effect of changes in detection rates and management strategies. The cost-effectiveness of different interventions to prevent vision loss from primary open-angle glaucoma was measured in terms of financial cost (Australian dollars) and disability-adjusted life years. The prevalence of glaucoma in Australia is expected to increase from 208 000 in 2005 to 379 000 in 2025 because of the aging population. Health system costs over the same time period are estimated to increase from $AU355 million to $AU784 million. Total costs (health system costs, indirect costs and costs of loss of well-being) will increase from $AU1.9 billion to $AU4.3 billion in Australia. Primary open-angle glaucoma poses a significant economic burden, which will increase substantially by 2025. This dynamic model provides a valuable tool for ongoing policy formulation and determining the economic impact of interventions to better prevent visual impairment and blindness from glaucoma. © 2011 The Authors. Clinical and Experimental Ophthalmology © 2011 Royal Australian and New Zealand College of Ophthalmologists.

Experimental evaluation of tritium permeation through stainless steel tubes of heat exchanger from primary to secondary water in ITER

International Nuclear Information System (INIS)

Nakamura, Hirofumi; Nishi, Masataka

2004-01-01

Tritium permeation through heat exchanger from primary cooling water to secondary cooling water has been investigated experimentally with SS316L heat exchanger under simulated ITER (international thermonuclear experimental reactor) operation condition in order to establish the tritium permeation evaluation method through the heat exchanger. As the result, the permeation rate of aqueous tritium was found to be about three orders smaller than that of the gaseous tritium. Tritium permeation through the heat exchanger in ITER was then evaluated, and it was revealed that total tritium permeation amount based on obtained aqueous permeability was about one order less than that with the former method with the gaseous permeability and putting the permeation reduction factor as 1000. Evaluated tritium permeation amount into secondary water during 20 years was quite small, which could be considered as negligible from the safety viewpoint

Cytogenetic as an Important Tool for Diagnosis and Prognosis for Patients with Hypocellular Primary Myelodysplastic Syndrome

Directory of Open Access Journals (Sweden)

Daiane Corrêa de Souza

2014-01-01

Full Text Available We analyzed cytogenetically 105 patients with hypocellular primary MDS and their clinical implications. The main chromosomal abnormalities found were del(5q/−5, del(6q/+6, del(7q/−7, del(11q, and del(17p. Pediatric patients had a higher frequency of abnormal karyotypes compared with adult patients (P < 0,05. From our patients, 18% showed evolution of the disease. The chromosomal abnormalities presented in the diagnosis of patients who evolved to AML included numerical (−7, +8 and structural del(6q, del(7q, i(7q, t(7;9, i(9q, and del(11q abnormalities and complex karyotypes. Although the frequency of evolution from hypocellular MDS to AML is low, our results suggest that some chromosomal alterations may play a critical role during this process. We applied the IPSS in our patients because this score system has been proved to be useful for predicting evolution of disease. When we considered the patients according to group 1 (intermediate-1 and group 2 (intermediate-2 and high risk, we showed that group 2 had a high association with respect to the frequency of abnormal karyotypes (P < 0,0001, evolution of disease (P < 0,0001, and mortality (P < 0,001. In fact, the cytogenetic analysis for patients with hypocellular primary MDS is an important tool for diagnosis, prognosis, in clinical decision-making and in follow-up.

COLPOSCOPY- A PRIMARY ALTERNATIVE SCREENING TOOL FOR CERVICAL PRE-CANCER

Directory of Open Access Journals (Sweden)

Srinivas Sangisapu

2017-09-01

Full Text Available BACKGROUND Cancer cervix is the most common and preventable malignancy in females. 80% of cases in India are detected in advanced stages. Paucity of cytologists in India is one of the important reasons for failure of screening by Pap smear. Visual Inspection of cervix with Acetic acid (VIA and Visual Inspection of cervix with application of Lugol’s Iodine (VILI are two alternative strategies in low resource settings. Colposcopy involves the same principles of VIA and VILI under better magnification. We have hospitals with not so low resource settings, where gynaecologists are available, but cytologists are not. We need to evolve an alternative strategy appropriate to our resources such as colposcopy and guided biopsy. The aim of the present study is to evaluate the feasibility of colposcopy as an alternative screening tool for cervical precancer. The objective of the study is therefore to compare the colposcopy with the known reference standard that is Pap smear and evaluate the sensitivity, specificity and predictive values. MATERIALS AND METHODS 3000 women were compared with simultaneous colposcopy and Pap smear with latter as reference standard. Colposcopy-guided cervical biopsy was performed for suspicious lesions. RESULTS Unsatisfactory colposcopy due to nonvisualisation of transformation zone is an insignificant percentage (1.7%. The sensitivity, specificity, positive and negative predictive values of colposcopy for the threshold of normal versus all grades of abnormality (all age groups and all abnormal reports included are 76.74%, 99.34%, 63.46% and 99.65%, respectively. Pap smear is taken as a reference standard. This is the primary objective of our study. Colposcopy-guided biopsy specimens of minor abnormal colposcopic lesions falling outside the transformation zone have not yielded any abnormal findings on histopathology. Three high-grade lesions were detected by colposcopy as well as Pap smear. They have also positively

Effect of cutting edge preparation on tool performance in hard-turning of DF-3 tool steel with ceramic tools

Energy Technology Data Exchange (ETDEWEB)

Davoudinejad, A.; Noordin, M. Y. [Universiti Teknologi Malaysia, Skudai (Malaysia)

2014-11-15

This study presents an experimental investigation on turning hardened DF-3 tool steel (∼ 58HRC) with PVD-TiN coated mixed ceramic. We focused on the effect of chamfer and honed edge geometry on tool wear, tool life, cutting forces and surface finish of the machined work piece. The effects of the process parameters on performance characteristics were investigated using ANOVA. It was found that longer tool life was recorded with chamfered edge geometry at various cutting conditions. The typical damage observed as flank and crater wear for ceramic tools and abrasive wear was found as the main mechanism.The optimal cutting speed was 155 m/min, with which a tolerable tool life and volume of material removal was obtained for both edges geometry. Finer machined surface was left by chamfered tool with feeds and speeds in the range of 0.125-0.05 mm/rev and 155-210 m/min, respectively; also, cutting forces decrease with increased cutting speed. The obtained consequence of cutting forces shows that tool wear has a considerable effect on cutting forces and greater forces values recorded with honed tools.

Effect of cutting edge preparation on tool performance in hard-turning of DF-3 tool steel with ceramic tools

International Nuclear Information System (INIS)

Davoudinejad, A.; Noordin, M. Y.

2014-01-01

This study presents an experimental investigation on turning hardened DF-3 tool steel (∼ 58HRC) with PVD-TiN coated mixed ceramic. We focused on the effect of chamfer and honed edge geometry on tool wear, tool life, cutting forces and surface finish of the machined work piece. The effects of the process parameters on performance characteristics were investigated using ANOVA. It was found that longer tool life was recorded with chamfered edge geometry at various cutting conditions. The typical damage observed as flank and crater wear for ceramic tools and abrasive wear was found as the main mechanism.The optimal cutting speed was 155 m/min, with which a tolerable tool life and volume of material removal was obtained for both edges geometry. Finer machined surface was left by chamfered tool with feeds and speeds in the range of 0.125-0.05 mm/rev and 155-210 m/min, respectively; also, cutting forces decrease with increased cutting speed. The obtained consequence of cutting forces shows that tool wear has a considerable effect on cutting forces and greater forces values recorded with honed tools.

The '3Is' of animal experimentation.

Science.gov (United States)

2012-05-29

Animal experimentation in scientific research is a good thing: important, increasing and often irreplaceable. Careful experimental design and reporting are at least as important as attention to welfare in ensuring that the knowledge we gain justifies using live animals as experimental tools.

Dynamic Modelling with "MLE-Energy Dynamic" for Primary School

Science.gov (United States)

Giliberti, Enrico; Corni, Federico

During the recent years simulation and modelling are growing instances in science education. In primary school, however, the main use of software is the simulation, due to the lack of modelling software tools specially designed to fit/accomplish the needs of primary education. In particular primary school teachers need to use simulation in a framework that is both consistent and simple enough to be understandable by children [2]. One of the possible area to approach modelling is about the construction of the concept of energy, in particular for what concerns the relations among substance, potential, power [3]. Following the previous initial research results with this approach [2], and with the static version of the software MLE Energy [1], we suggest the design and the experimentation of a dynamic modelling software—MLE dynamic-capable to represent dynamically the relations occurring when two substance-like quantities exchange energy, modifying their potential. By means of this software the user can graphically choose the dependent and independent variables and leave the other parameters fixed. The software has been initially evaluated, during a course of science education with a group of primary school teachers-to-be, to test the ability of the software to improve teachers' way of thinking in terms of substance-like quantities and their effects (graphical representation of the extensive, intensive variables and their mutual relations); moreover, the software has been tested with a group of primary school teachers, asking their opinion about the software didactical relevance in the class work.

Using the Tools and Resources of the RCSB Protein Data Bank.

Science.gov (United States)

Costanzo, Luigi Di; Ghosh, Sutapa; Zardecki, Christine; Burley, Stephen K

2016-09-07

The Protein Data Bank (PDB) archive is the worldwide repository of experimentally determined three-dimensional structures of large biological molecules found in all three kingdoms of life. Atomic-level structures of these proteins, nucleic acids, and complex assemblies thereof are central to research and education in molecular, cellular, and organismal biology, biochemistry, biophysics, materials science, bioengineering, ecology, and medicine. Several types of information are associated with each PDB archival entry, including atomic coordinates, primary experimental data, polymer sequence(s), and summary metadata. The Research Collaboratory for Structural Bioinformatics Protein Data Bank (RCSB PDB) serves as the U.S. data center for the PDB, distributing archival data and supporting both simple and complex queries that return results. These data can be freely downloaded, analyzed, and visualized using RCSB PDB tools and resources to gain a deeper understanding of fundamental biological processes, molecular evolution, human health and disease, and drug discovery. © 2016 by John Wiley & Sons, Inc. Copyright © 2016 John Wiley & Sons, Inc.

[Design of an educational tool for Primary Care patients with chronic non-specific low back pain].

Science.gov (United States)

Díaz-Cerrillo, Juan Luis; Rondón-Ramos, Antonio

2015-02-01

Current scientific evidence on the management of chronic non-specific low back pain highlights the benefits of physical exercise. This goal is frequently undermined due to lack of education of the subjects on the multifactorial, benign, and non-specific nature of low back pain, which can lead to a chronic disease with genuine psychosocial risk factors. Its influence may not only interfere with individual decision to adopt more adaptive coping behaviors, but also with the endogenous mechanisms of pain neuromodulation. Thus, the educational strategies and control of these factors have become important objectives to be incorporated into the management of the disorder and research guidelines. This paper presents the theoretical models and the scientific basis on which it has based the design of an educational tool for patients with chronic non-specific low back pain treated in Primary Care physiotherapy. Structure, content and objectives are also presented. Copyright © 2013 Elsevier España, S.L.U. All rights reserved.

Active control of residual tool marks for freeform optics functionalization by novel biaxial servo assisted fly cutting.

Science.gov (United States)

Zhu, Zhiwei; To, Suet; Zhang, Shaojian

2015-09-01

The inherent residual tool marks (RTM) with particular patterns highly affect optical functions of the generated freeform optics in fast tool servo or slow tool servo (FTS/STS) diamond turning. In the present study, a novel biaxial servo assisted fly cutting (BSFC) method is developed for flexible control of the RTM to be a functional micro/nanotexture in freeform optics generation, which is generally hard to achieve in FTS/STS diamond turning. In the BSFC system, biaxial servo motions along the z-axis and side-feeding directions are mainly adopted for primary surface generation and RTM control, respectively. Active control of the RTM from the two aspects, namely, undesired effect elimination or effective functionalization, are experimentally demonstrated by fabricating a typical F-theta freeform surface with scattering homogenization and two functional microstructures with imposition of secondary phase gratings integrating both reflective and diffractive functions.

Experimental and numerical investigations on the temperature distribution in PVD AlTiN coated and uncoated Al2O3/TiCN mixed ceramic cutting tools in hard turning of AISI 52100 steel

Science.gov (United States)

Sateesh Kumar, Ch; Patel, Saroj Kumar; Das, Anshuman

2018-03-01

Temperature generation in cutting tools is one of the major causes of tool failure especially during hard machining where machining forces are quite high resulting in elevated temperatures. Thus, the present work investigates the temperature generation during hard machining of AISI 52100 steel (62 HRC hardness) with uncoated and PVD AlTiN coated Al2O3/TiCN mixed ceramic cutting tools. The experiments were performed on a heavy duty lathe machine with both coated and uncoated cutting tools under dry cutting environment. The temperature of the cutting zone was measured using an infrared thermometer and a finite element model has been adopted to predict the temperature distribution in cutting tools during machining for comparative assessment with the measured temperature. The experimental and numerical results revealed a significant reduction of cutting zone temperature during machining with PVD AlTiN coated cutting tools when compared to uncoated cutting tools during each experimental run. The main reason for decrease in temperature for AlTiN coated tools is the lower coefficient of friction offered by the coating material which allows the free flow of the chips on the rake surface when compared with uncoated cutting tools. Further, the superior wear behaviour of AlTiN coating resulted in reduction of cutting temperature.

[Videocapsule endoscopy as a useful tool to diagnose primary intestinal lymphangiectasia].

Science.gov (United States)

Vignes, S; Bellanger, J

2007-03-01

Primary intestinal lymphangiectasia (Waldmann's disease) lead to a protein-losing enteropathy due to lymph leak into intestinal tract. A 28-year-old woman presented a bilateral lower limb lymphedema. Laboratory examination showing lymphopenia, hypoalbuminemia, hypogammaglobulinemia suggested the diagnosis of primary intestinal lymphangiectasia. Gastroscopy was normal and second duodenum biopsies were negative. Videocapsule endoscopy gave evidence of intestinal lymphangiectasia of the small bowel. Videocapsule endoscopy may be proposed to confirm intestinal lymphangiectasia and to precise their localization when gastroscopy is not conclusive.

Use of mobile health (mHealth) tools by primary care patients in the WWAMI region Practice and Research Network (WPRN).

Science.gov (United States)

Bauer, Amy M; Rue, Tessa; Keppel, Gina A; Cole, Allison M; Baldwin, Laura-Mae; Katon, Wayne

2014-01-01

The purpose of this study was to determine the prevalence of mobile health (mHealth) use among primary care patients and examine demographic and clinical correlates. Adult patients who presented to 1 of 6 primary care clinics in a practice-based research network in the northwest United States during a 2-week period received a survey that assessed smartphone ownership; mHealth use; sociodemographic characteristics (age, sex, race/ethnicity, health literacy); chronic conditions; and depressive symptoms (2-item Patient Health Questionnaire). Data analysis used descriptive statistics and mixed logistic regression. Of 918 respondents (estimated response rate, 67.4%), 55% owned a smartphone, among whom 70% were mHealth users. In multivariate analyses, smartphone ownership and mHealth use were not associated with health literacy, chronic conditions, or depression but were less common among adults >45 years old (adjusted odds ratio, 0.07-0.39; P mHealth tools from their physician, and few (31%) prioritized their provider's involvement. Use of mHealth technologies is lower among older adults but otherwise is common among primary care patients, including those with limited health literacy and those with chronic conditions. Findings support the potential role of mHealth in improving disease management among certain groups in need; however, greater involvement of health care providers may be important for realizing this potential. © Copyright 2014 by the American Board of Family Medicine.

Toward a Holistic Federated Future Internet Experimentation Environment: The Experience of NOVI Research and Experimentation

NARCIS (Netherlands)

Maglaris, V.; Papagianni, C.; Androulidakis, G.; Grammatikou, M.; Grosso, P.; van der Ham, J.; de Laat, C.; Pietrzak, B.; Belter, B.; Steger, J.; Laki, S.; Campanella, M.; Sallent, S.

This article presents the design and pilot implementation of a suite of intelligent methods, algorithms, and tools for federating heterogeneous experimental platforms (domains) toward a holistic Future Internet experimentation ecosystem. The proposed framework developed within the NOVI research and

Technics Research on Polycrystalline Cubic Boron Nitride Cutting Tools Dry Turning Ti-6AL-4V Alloy Based on Orthogonal Experimental Design

Directory of Open Access Journals (Sweden)

Jia Yunhai

2018-01-01

Full Text Available Ti-6Al-4V components are the most widely used titanium alloy products not only in the aerospace industry, but also for bio-medical applications. The machine-ability of titanium alloys is impaired by their high temperature chemical reactivity, low thermal conductivity and low modulus of elasticity. Polycrystalline cubic boron nitride represents a substitute tool material for turning titanium alloys due to its high hardness, wear resistance, thermal stability and hot red hardness. For determination of suitable cutting parameters in dry turning Ti-6AL-4V alloy by Polycrystalline cubic boron nitride cutting tools, the samples, 300mm in length and 100mm in diameter, were dry machined in a lathe. The turning suitable parameters, such as cutting speed, feed rate and cut depth were determined according to workpieces surface roughness and tools flank wear based on orthogonal experimental design. The experiment showed that the cutting speed in the range of 160~180 m/min, the feed rate is 0.15 mm/rev and the depth of cut is 0.20mm, ideal workpiece surface roughness and little cutting tools flank wear can be obtained.

Justification for parameters of a dynamic stabilizer of the experimental stand mobile unit in studying of active rotational working tools of tiller machines

Directory of Open Access Journals (Sweden)

Vladimir F. Kupryashkin

2017-03-01

Full Text Available Introduction: The article deals with design options and technological modes of the dynamic stabilizer of the experimental stand mobile unit for studying tillage machine active rotating work tools. Based on theoretical and experimental studies, the possibility the movable module instability was discovered. This negatively affects on implementing the experiment program trough the especific method. The need in engineering solutions for the defect correction is shown. In addition, the authors consider the structural features and characteristics of the used devices for providing the stabilization of the movable module in the study of active rotating work tools of tillage machines. An electromagnetic brake dynamic stabilizer in the structure of the existing rolling module was proposed as an engineering device. Materials and Methods: A theoretical study of rolling module stability, based on synthesis of basic regulations and laws of mechanics related to active rotating work tools was conducted. As a result of the theoretical research, a design scheme of movable module loading was created. This scheme includes the design features and structural power factors. Results: A database representing the settings of power specification in the motion stability determining the mobile unit was created. Further use of the database values allow supporting the most optimal location of the electromagnetic brake with its design options. Discussion and Conclusions: The research of the electromagnetic brake in a mobile unit promoted stabilizing the unit movement, increased the frequency of its use and provided data that are more precise during experiments.

Modeling and Tool Wear in Routing of CFRP

International Nuclear Information System (INIS)

Iliescu, D.; Fernandez, A.; Gutierrez-Orrantia, M. E.; Lopez de Lacalle, L. N.; Girot, F.

2011-01-01

This paper presents the prediction and evaluation of feed force in routing of carbon composite material. In order to extend tool life and improve quality of the machined surface, a better understanding of uncoated and coated tool behaviors is required. This work describes (1) the optimization of the geometry of multiple teeth tools minimizing the tool wear and the feed force, (2) the optimization of tool coating and (3) the development of a phenomenological model between the feed force, the routing parameters and the tool wear. The experimental results indicate that the feed rate, the cutting speed and the tool wear are the most significant factors affecting the feed force. In the case of multiple teeth tools, a particular geometry with 14 teeth right helix right cut and 11 teeth left helix right cut gives the best results. A thick AlTiN coating or a diamond coating can dramatically improve the tool life while minimizing the axial force, roughness and delamination. A wear model has then been developed based on an abrasive behavior of the tool. The model links the feed rate to the tool geometry parameters (tool diameter), to the process parameters (feed rate, cutting speed and depth of cut) and to the wear. The model presented has been verified by experimental tests.

MediPlEx - a tool to combine in silico & experimental gene expression profiles of the model legume Medicago truncatula

Directory of Open Access Journals (Sweden)

Stutz Leonhard J

2010-10-01

Full Text Available Abstract Background Expressed Sequence Tags (ESTs are in general used to gain a first insight into gene activities from a species of interest. Subsequently, and typically based on a combination of EST and genome sequences, microarray-based expression analyses are performed for a variety of conditions. In some cases, a multitude of EST and microarray experiments are conducted for one species, covering different tissues, cell states, and cell types. Under these circumstances, the challenge arises to combine results derived from the different expression profiling strategies, with the goal to uncover novel information on the basis of the integrated datasets. Findings Using our new analysis tool, MediPlEx (MEDIcago truncatula multiPLe EXpression analysis, expression data from EST experiments, oligonucleotide microarrays and Affymetrix GeneChips® can be combined and analyzed, leading to a novel approach to integrated transcriptome analysis. We have validated our tool via the identification of a set of well-characterized AM-specific and AM-induced marker genes, identified by MediPlEx on the basis of in silico and experimental gene expression profiles from roots colonized with AM fungi. Conclusions MediPlEx offers an integrated analysis pipeline for different sets of expression data generated for the model legume Medicago truncatula. As expected, in silico and experimental gene expression data that cover the same biological condition correlate well. The collection of differentially expressed genes identified via MediPlEx provides a starting point for functional studies in plant mutants. MediPlEx can freely be used at http://www.cebitec.uni-bielefeld.de/mediplex.

Experimental and Mathematical Modeling for Prediction of Tool Wear on the Machining of Aluminium 6061 Alloy by High Speed Steel Tools

Directory of Open Access Journals (Sweden)

Okokpujie Imhade Princess

2017-12-01

Full Text Available In recent machining operation, tool life is one of the most demanding tasks in production process, especially in the automotive industry. The aim of this paper is to study tool wear on HSS in end milling of aluminium 6061 alloy. The experiments were carried out to investigate tool wear with the machined parameters and to developed mathematical model using response surface methodology. The various machining parameters selected for the experiment are spindle speed (N, feed rate (f, axial depth of cut (a and radial depth of cut (r. The experiment was designed using central composite design (CCD in which 31 samples were run on SIEG 3/10/0010 CNC end milling machine. After each experiment the cutting tool was measured using scanning electron microscope (SEM. The obtained optimum machining parameter combination are spindle speed of 2500 rpm, feed rate of 200 mm/min, axial depth of cut of 20 mm, and radial depth of cut 1.0mm was found out to achieved the minimum tool wear as 0.213 mm. The mathematical model developed predicted the tool wear with 99.7% which is within the acceptable accuracy range for tool wear prediction.

Experimental and Mathematical Modeling for Prediction of Tool Wear on the Machining of Aluminium 6061 Alloy by High Speed Steel Tools

Science.gov (United States)

Okokpujie, Imhade Princess; Ikumapayi, Omolayo M.; Okonkwo, Ugochukwu C.; Salawu, Enesi Y.; Afolalu, Sunday A.; Dirisu, Joseph O.; Nwoke, Obinna N.; Ajayi, Oluseyi O.

2017-12-01

In recent machining operation, tool life is one of the most demanding tasks in production process, especially in the automotive industry. The aim of this paper is to study tool wear on HSS in end milling of aluminium 6061 alloy. The experiments were carried out to investigate tool wear with the machined parameters and to developed mathematical model using response surface methodology. The various machining parameters selected for the experiment are spindle speed (N), feed rate (f), axial depth of cut (a) and radial depth of cut (r). The experiment was designed using central composite design (CCD) in which 31 samples were run on SIEG 3/10/0010 CNC end milling machine. After each experiment the cutting tool was measured using scanning electron microscope (SEM). The obtained optimum machining parameter combination are spindle speed of 2500 rpm, feed rate of 200 mm/min, axial depth of cut of 20 mm, and radial depth of cut 1.0mm was found out to achieved the minimum tool wear as 0.213 mm. The mathematical model developed predicted the tool wear with 99.7% which is within the acceptable accuracy range for tool wear prediction.

Chatter and machine tools

CERN Document Server

Stone, Brian

2014-01-01

Focussing on occurrences of unstable vibrations, or Chatter, in machine tools, this book gives important insights into how to eliminate chatter with associated improvements in product quality, surface finish and tool wear. Covering a wide range of machining processes, including turning, drilling, milling and grinding, the author uses his research expertise and practical knowledge of vibration problems to provide solutions supported by experimental evidence of their effectiveness. In addition, this book contains links to supplementary animation programs that help readers to visualise the ideas detailed in the text. Advancing knowledge in chatter avoidance and suggesting areas for new innovations, Chatter and Machine Tools serves as a handbook for those desiring to achieve significant reductions in noise, longer tool and grinding wheel life and improved product finish.

Evaluating the Implementation and Feasibility of a Web-Based Tool to Support Timely Identification and Care for the Frail Population in Primary Healthcare Settings

Directory of Open Access Journals (Sweden)

Beverley Lawson

2017-07-01

Full Text Available Background Understanding and addressing the needs of frail persons is an emerging health priority for Nova Scotia and internationally. Primary healthcare (PHC providers regularly encounter frail persons in their daily clinical work. However, routine identification and measurement of frailty is not standard practice and, in general, there is a lack of awareness about how to identify and respond to frailty. A web-based tool called the Frailty Portal was developed to aid in identifying, screening, and providing care for frail patients in PHC settings. In this study, we will assess the implementation feasibility and impact of the Frailty Portal to: (1 support increased awareness of frailty among providers and patients, (2 identify the degree of frailty within individual patients, and (3 develop and deliver actions to respond to frailtyl in community PHC practice. Methods This study will be approached using a convergent mixed method design where quantitative and qualitative data are collected concurrently, in this case, over a 9-month period, analyzed separately, and then merged to summarize, interpret and produce a more comprehensive understanding of the initiative’s feasibility and scalability. Methods will be informed by the ‘Implementing the Frailty Portal in Community Primary Care Practice’ logic model and questions will be guided by domains and constructs from an implementation science framework, the Consolidated Framework for Implementation Research (CFIR. Discussion The ‘Frailty Portal’ aims to improve access to, and coordination of, primary care services for persons experiencing frailty. It also aims to increase primary care providers’ ability to care for patients in the context of their frailty. Our goal is to help optimize care in the community by helping community providers gain the knowledge they may lack about frailty both in general and in their practice, support improved identification of frailty with the use of screening

Bipedal tool use strengthens chimpanzee hand preferences

DEFF Research Database (Denmark)

Braccini, Stephanie; Lambeth, Susan; Schapiro, Steve

2010-01-01

The degree to which non-human primate behavior is lateralized, at either individual or population levels, remains controversial. We investigated the relationship between hand preference and posture during tool use in chimpanzees (Pan troglodytes) during bipedal tool use. We experimentally induced...

Experimental determination of primary and intermediate ions in a flame front

Energy Technology Data Exchange (ETDEWEB)

Fialkov, A.B.; Fialkov, B.S.

1988-10-01

A procedure is described for determining the primary and intermediate ions in the front of a flame rarefied using mass spectrometry. By using the method proposed here, primary CHO(+) and CHO2(+) ions as well as a series of short-lived intermediate ions have been identified. The possibility of using this method for obtaining quantitative data on the characteristic lifetimes of ions and rate constants of ion-molecular reactions in flames is demonstrated. 16 references.

Implementation and impact of an online tool used in primary care to improve access to financial benefits for patients: a study protocol.

Science.gov (United States)

Aery, Anjana; Rucchetto, Anne; Singer, Alexander; Halas, Gayle; Bloch, Gary; Goel, Ritika; Raza, Danyaal; Upshur, Ross E G; Bellaire, Jackie; Katz, Alan; Pinto, Andrew David

2017-10-22

Addressing the social determinants of health has been identified as crucial to reducing health inequities. However, few evidence-based interventions exist. This study emerges from an ongoing collaboration between physicians, researchers and a financial literacy organisation. Our study will answer the following: Is an online tool that improves access to financial benefits feasible and acceptable? Can such a tool be integrated into clinical workflow? What are patient perspectives on the tool and what is the short-term impact on access to benefits? An advisory group made up of patients living on low incomes and representatives from community agencies supports this study. We will recruit three primary care sites in Toronto, Ontario and three in Winnipeg, Manitoba that serve low-income communities. We will introduce clinicians to screening for poverty and how benefits can increase income. Health providers will be encouraged to use the tool with any patient seen. The health provider and patient will complete the online tool together, generating a tailored list of benefits and resources to assist with obtaining these benefits. A brief survey on this experience will be administered to patients after they complete the tool, as well as a request to contact them in 1 month. Those who agree to be contacted will be interviewed on whether the intervention improved access to financial benefits. We will also administer an online survey to providers and conduct focus groups at each site. Key ethical concerns include that patients may feel discomfort when being asked about their financial situation, may feel obliged to complete the tool and may have their expectations falsely raised about receiving benefits. Providers will be trained to address each of these concerns. We will share our findings with providers and policy-makers interested in addressing the social determinants of health within healthcare settings. Clinicaltrials.gov: NCT02959866. Registered 7 November 2016

Congruency in the prediction of pathogenic missense mutations: state-of-the-art web-based tools.

Science.gov (United States)

Castellana, Stefano; Mazza, Tommaso

2013-07-01

A remarkable degree of genetic variation has been found in the protein-encoding regions of DNA through deep sequencing of samples obtained from thousands of subjects from several populations. Approximately half of the 20 000 single nucleotide polymorphisms present, even in normal healthy subjects, are nonsynonymous amino acid substitutions that could potentially affect protein function. The greatest challenges currently facing investigators are data interpretation and the development of strategies to identify the few gene-coding variants that actually cause or confer susceptibility to disease. A confusing array of options is available to address this problem. Unfortunately, the overall accuracy of these tools at ultraconserved positions is low, and predictions generated by current computational tools may mislead researchers involved in downstream experimental and clinical studies. First, we have presented an updated review of these tools and their primary functionalities, focusing on those that are naturally prone to analyze massive variant sets, to infer some interesting similarities among their results. Additionally, we have evaluated the prediction congruency for real whole-exome sequencing data in a proof-of-concept study on some of these web-based tools.

0.20-m (8-in.) primary burner development report

International Nuclear Information System (INIS)

Stula, R.T.; Young, D.T.; Rode, J.S.

1977-12-01

High-Temperature Gas-Cooled Reactors (HTGRs) utilize graphite-base fuels. Fluidized-bed burners are being employed successfully in the experimental reprocessing of these fuels. The primary fluidized-bed burner is a unit operation in the reprocessing flowsheet in which the graphite moderator is removed. A detailed description of the development status of the 0.20-m (8-in.) diameter primary fluidized-bed burner as of July 1, 1977 is presented. Experimental work to date performed in 0.10; 0.20; and 0.40-m (4, 8, and 16 in.) diameter primary burners has demonstrated the feasibility of the primary burning process and, at the same time, has defined more clearly the areas in which additional experimental work is required. The design and recent operating history of the 0.20-m-diameter burner are discussed, with emphasis placed upon the evolution of the current design and operating philosophy

Math’s teaching through cooperative learning in year-2 Primary Education

Directory of Open Access Journals (Sweden)

Jesús Iglesias Muñiz

2017-05-01

Full Text Available The goal of this study was to assess the effects of cooperative learning as a methodological tool for maths teaching. A quasi-experimental design with non-equivalent groups of students was used. A total of 33 students belonging to two year-2 Primary Education intact classes agreed to participate. One experienced a cooperative learning approach, while the other one experienced a traditional approach. Assessment was performed quantitatively through a maths’ skills test and qualitatively through children’s drawings. Quantitative results showed that the cooperative learning group reached higher math scores, while from the qualitative results emerged 3 positive categories: enjoyment, learning, group work and 3 negative: boredom/tiredness, difficult and bad behaviour. Cooperative learning seems to debilitate students’ negative perceptions on the math class.

πScope: Python based scientific workbench with MDSplus data visualization tool

Energy Technology Data Exchange (ETDEWEB)

Shiraiwa, S., E-mail: shiraiwa@PSFC.MIT.EDU; Fredian, T.; Hillairet, J.; Stillerman, J.

2016-11-15

Highlights: • πScope provides great enhancement in MDSplus data visualization. • πScope provides a single platform for both data browsing and complicated analysis. • πScope is scriptable and easily expandable due to its object oriented. • πScope is written in python and available from (http://piscope.psfc.mit.edu/). - Abstract: A newly developed python based scientific data analysis and visualization tool, πScope ( (http://piscope.psfc.mit.edu)), is reported. The primary motivation is 1) to provide an updated tool to browse the MDSplus data beyond existing dwscope/jScope and 2) to realize a universal foundation to construct interface tools to perform computer modeling from experimental data. To visualize MDSplus data, πScope has many features including overplotting different signals and discharges, generating various plot types (line, contour, image, etc.), performing in-panel data analysis using python scripts, and producing publication quality graphics. The logic to generate multi-panel plots is designed to be backward compatible with dwscope, enabling smooth migration for users. πScope uses multi-threading in data loading, and is easy to modify and expand due to its object-oriented design. Furthermore, A user can access the data structure both from a GUI and a script, enabling relatively complex data analysis workflow built quickly on πScope.

πScope: Python based scientific workbench with MDSplus data visualization tool

International Nuclear Information System (INIS)

Shiraiwa, S.; Fredian, T.; Hillairet, J.; Stillerman, J.

2016-01-01

Highlights: • πScope provides great enhancement in MDSplus data visualization. • πScope provides a single platform for both data browsing and complicated analysis. • πScope is scriptable and easily expandable due to its object oriented. • πScope is written in python and available from (http://piscope.psfc.mit.edu/). - Abstract: A newly developed python based scientific data analysis and visualization tool, πScope ( (http://piscope.psfc.mit.edu)), is reported. The primary motivation is 1) to provide an updated tool to browse the MDSplus data beyond existing dwscope/jScope and 2) to realize a universal foundation to construct interface tools to perform computer modeling from experimental data. To visualize MDSplus data, πScope has many features including overplotting different signals and discharges, generating various plot types (line, contour, image, etc.), performing in-panel data analysis using python scripts, and producing publication quality graphics. The logic to generate multi-panel plots is designed to be backward compatible with dwscope, enabling smooth migration for users. πScope uses multi-threading in data loading, and is easy to modify and expand due to its object-oriented design. Furthermore, A user can access the data structure both from a GUI and a script, enabling relatively complex data analysis workflow built quickly on πScope.

Learning to teach geography for primary education : Results of an experimental programme

NARCIS (Netherlands)

Blankman, M.; Schoonenboom, J.; van der Schee, J.; Boogaard, M.; Volman, M.

2016-01-01

Students training to become primary school teachers appear to have little awareness of the core concepts of geography (teaching). To ensure that future primary school teachers are able to develop their pupils’ geographical awareness, a six weeks programme was developed. The characteristics of this

Active Living: development and quasi-experimental evaluation of a school-centered physical activity intervention for primary school children.

Science.gov (United States)

Van Kann, Dave H H; Jansen, M W J; de Vries, S I; de Vries, N K; Kremers, S P J

2015-12-29

The worldwide increase in the rates of childhood overweight and physical inactivity requires successful prevention and intervention programs for children. The aim of the Active Living project is to increase physical activity and decrease sedentary behavior of Dutch primary school children by developing and implementing tailored, multicomponent interventions at and around schools. In this project, school-centered interventions have been developed at 10 schools in the south of the Netherlands, using a combined top-down and bottom-up approach in which a research unit and a practice unit continuously interact. The interventions consist of a combination of physical and social interventions tailored to local needs of intervention schools. The process and short- and long-term effectiveness of the interventions will be evaluated using a quasi-experimental study design in which 10 intervention schools are matched with 10 control schools. Baseline and follow-up measurements (after 12 and 24 months) have been conducted in grades 6 and 7 and included accelerometry, GPS, and questionnaires. Primary outcome of the Active Living study is the change in physical activity levels, i.e. sedentary behavior (SB), light physical activity (LPA), moderate-to-vigorous physical activity (MVPA), and counts-per-minute (CPM). Multilevel regression analyses will be used to assess the effectiveness of isolated and combined physical and social interventions on children's PA levels. The current intervention study is unique in its combined approach of physical and social environmental PA interventions both at school(yard)s as well as in the local neighborhood around the schools. The strength of the study lies in the quasi-experimental design including objective measurement techniques, i.e. accelerometry and GPS, combined with more subjective techniques, i.e. questionnaires, implementation logbooks, and neighborhood observations. Current Controlled Trials ISRCTN25497687 (registration date 21

Minimization of Surface Roughness and Tool Vibration in CNC Milling Operation

Directory of Open Access Journals (Sweden)

Sukhdev S. Bhogal

2015-01-01

Full Text Available Tool vibration and surface roughness are two important parameters which affect the quality of the component and tool life which indirectly affect the component cost. In this paper, the effect of cutting parameters on tool vibration, and surface roughness has been investigated during end milling of EN-31 tool steel. Response surface methodology (RSM has been used to develop mathematical model for predicting surface finish, tool vibration and tool wear with different combinations of cutting parameters. The experimental results show that feed rate is the most dominating parameter affecting surface finish, whereas cutting speed is the major factor effecting tool vibration. The results of mathematical model are in agreement with experimental investigations done to validate the mathematical model.

Method for automation of tool preproduction

Science.gov (United States)

Rychkov, D. A.; Yanyushkin, A. S.; Lobanov, D. V.; Arkhipov, P. V.

2018-03-01

The primary objective of tool production is a creation or selection of such tool design which could make it possible to secure high process efficiency, tool availability as well as a quality of received surfaces with minimum means and resources spent on it. It takes much time of application people, being engaged in tool preparation, to make a correct selection of the appropriate tool among the set of variants. Program software has been developed to solve the problem, which helps to create, systematize and carry out a comparative analysis of tool design to identify the rational variant under given production conditions. The literature indicates that systematization and selection of the tool rational design has been carried out in accordance with the developed modeling technology and comparative design analysis. Software application makes it possible to reduce the period of design by 80....85% and obtain a significant annual saving.

Learning to Teach Geography for Primary Education: Results of an Experimental Programme

Science.gov (United States)

Blankman, Marian; Schoonenboom, Judith; van der Schee, Joop; Boogaard, Marianne; Volman, Monique

2016-01-01

Students training to become primary school teachers appear to have little awareness of the core concepts of geography (teaching). To ensure that future primary school teachers are able to develop their pupils' geographical awareness, a six weeks programme was developed. The characteristics of this programme -- named Consciously Teaching Geography…

Validation of the Spanish version of the fibromyalgia rapid screening tool to detect fibromyalgia in primary care health centres.

Science.gov (United States)

Casanueva, Benigno; Belenguer, Rafael; Moreno-Muelas, José V; Urtiaga, Javier; Urtiaga, Blanca; Hernández, José L; Pina, Trinitario; González-Gay, Miguel A

2016-01-01

To investigate the reliability and validity of the Spanish version of the Fibromyalgia Rapid Screening Tool (FiRST), a brief questionnaire for the detection of fibromyalgia (FM) in patients with diffuse chronic pain seen at primary care health centres. The original FiRST French questionnaire was adapted to a Spanish version following the guidelines of the Rheumatology Spanish Society Study Group of FM, and the help provided by professors of French and Spanish Language. In a prospective and multicentre study, patients with chronic pain were initially divided into two groups: a group that included patients that had been diagnosed with FM according to the 1990 ACR criteria and the 2010 ACR preliminary criteria (n=404), and a non-FM (control) group composed of rheumatoid arthritis (RA) (n=147) and osteoarthritis (OA) (n=219) patients. Patients from the FM group were evaluated by assessing tender point assessment, Widespread Pain Index (WPI), Symptom Severity Scale (SSS), FiRST questionnaire and Fibromyalgia Impact Questionnaire (FIQ). The non-FM group was evaluated by means of FiRST, WPI and SSS. Sensitivity, specificity and predictive value as well as the correlation between the global score and other parameters were assessed. 356 of 404 FM (88.1%) patients who met the 1990 ACR criteria and the ACR 2010 preliminary criteria had a positive FiRST. In the control group (AR plus OA), only 16 (4.4%) subjects had a positive FiRST. The sensitivity value was 92% (95% confidence interval CI: 88.9-95.1), specificity 87.4% (95% CI: 80.8-94.0), positive predictive value 95.7% (95% CI: 93.3-98.1), and negative predictive value 78.2% (95% CI: 70.6-85.9). A significant correlation between the total FiRST score (patients with score 5 or 6) and WPI (pFIQ (p<0.0001) was found. FiRST questionnaire is a useful tool for the detection of FM in primary care health centres.

Thinkering through Experiments: Nurturing Transdisciplinary Approaches to the Design of Testing Tools

Directory of Open Access Journals (Sweden)

Kathryn B. Francis

2017-11-01

Full Text Available In order to assess and understand human behavior, traditional approaches to experimental design incorporate testing tools that are often artificial and devoid of corporeal features. Whilst these offer experimental control in situations in which, methodologically, real behaviors cannot be examined, there is increasing evidence that responses given in these contextually deprived experiments fail to trigger genuine responses. This may result from a lack of consideration regarding the material makeup and associations connected with the fabric of experimental tools. In a two-year collaboration, we began to experiment with the physicality of testing tools using the domain of moral psychology as a case study. This collaboration involved thinkering and prototyping methods that included direct contact and consideration of the materials involved in experimentation. Having explored the embodied nature of morality, we combined approaches from experimental psychology, moral philosophy, design thinking, and computer science to create a new testing tool for simulated moral behavior. Although the testing tool itself generated fruitful results, this paper considers the collaborative methodology through which it was produced as a route to highlight material questions within psychological research.

Geometrical characterization of micro end milling tools

DEFF Research Database (Denmark)

Borsetto, Francesca; Bariani, Paolo; Bissacco, Giuliano

2005-01-01

Performance of the milling process is directly affected by the accuracy of tool geometry. Development of methods suitable for dimensional characterization of such tools, with low measurement uncertainties is therefore of relevance. The present article focuses on the geometrical characterization...... of a flat micro end milling tool with a nominal mill diameter of 200 microns. An experimental investigation was carried out involving two different non-contact systems...

High - speed steel for precise cased tools

International Nuclear Information System (INIS)

Karwiarz, J.; Mazur, A.

2001-01-01

The test results of high-vanadium high - speed steel (SWV9) for precise casted tools are presented. The face -milling cutters of NFCa80A type have been tested in industrial operating conditions. An average life - time of SWV9 steel tools was 3-10 times longer compare to the conventional high - speed milling cutters. Metallography of SWB9 precise casted steel revealed beneficial for tool properties distribution of primary vanadium carbides in the steel matrix. Presented results should be a good argument for wide application of high - vanadium high - speed steel for precise casted tools. (author)

Experimental fast reactor JOYO MK-III functional test. Primary auxiliary cooling system test

International Nuclear Information System (INIS)

Karube, Koji; Akagi, Shinji; Terano, Toshihiro; Onuki, Osamu; Ito, Hideaki; Aoki, Hiroshi; Odo, Toshihiro

2004-03-01

This paper describes the results of primary auxiliary cooling system, which were done as a part of JOYO MK-III function test. The aim of the tests was to confirm the operational performance of primary auxiliary EMP and the protection system including siphon breaker of primary auxiliary cooling system. The items of the tests were: (Test No.): (Test item). 1) SKS-117: EMP start up test. 2) SKS-118-1: EMP start up test when pony motor running. 3) SKS-121: Function test of siphon breaker. The results of the tests satisfied the required performance, and demonstrated successful operation of primary auxiliary cooling system. (author)

Analytical and experimental evaluation of a proposed self-forging fragment munition

International Nuclear Information System (INIS)

Tuft, D.B.; Folsom, E.N.

1982-01-01

Analytical and experimental tools have been used to study the formation of a proposed self-forging fragment projectile. The primary objective of this study is the determination of the interior and exterior shape of the fully formed fragment, and to determine if the fragment tumbles in flight. In addition, it is of interest to compare computer predictions to experimental results. An experiment was performed using high speed photography and high-energy flash x-ray radiography to study liner and case motion and projectile formation. Fabrication and assembly tolerances were closely controlled in an effort to eliminate tolerances as a possible source of fragment instability. X-ray film-density contours were analyzed to determine the fully formed fragment interior and exterior shape. Down-range yaw screens showed fragment tumbling in flight. The computed fragment shape was compared to experimental results and it was found that a retaining ring in the computational model near the liner periphery had a significant effect on the final computed fragment shape. With the retaining ring in the computational model and full two-way sliding between all material interfaces, the final computed fragment showed very good agreement with the experiment on both exterior and interior shapes

Effect of photodynamic therapy (PDT) on Enterococcus faecalis biofilm in experimental primary and secondary endodontic infections.

Science.gov (United States)

Tennert, Christian; Feldmann, Katharina; Haamann, Edwina; Al-Ahmad, Ali; Follo, Marie; Wrbas, Karl-Thomas; Hellwig, Elmar; Altenburger, Markus J

2014-11-04

To determine the antibacterial effect of photodynamic Therapy on Enterococcus faecalis (E. faecalis) biofilms in experimentally infected human root canals in primary infections and endodontic retreatments. One hundred and sixty single-rooted extracted teeth with one root canal were prepared using ProTaper instruments. Seventy specimens were left without root canal filling and autoclaved. The root canals of another 70 specimens were filled with Thermafil and AH Plus and the root canal fillings were removed after 24 hours using ProTaper D files and plasma sterilized. The specimens were infected with a clinical isolate of E. faecalis for 72 hours. Samples were taken using sterile paper points to determine the presence of E. faecalis in the root canals. The specimens were randomly divided into groups according to their treatment with 20 teeth each and a control. In the PDT group the teeth were treated using PDT, consisting of the photosensitizer toluidine blue and the PDT light source at 635 nm. In the NaOCl (sodium hypochlorite) group the root canals were rinsed with 10 mL of 3% NaOCl. In the NaOCl-PDT group the root canals were rinsed with 10 mL of 3% of sodium hypochlorite and then treated with PDT. Samples were taken after treatments using sterile paper points. Additionally, remaining root canal filling material was recovered from the root canal walls. Survival fractions of the samples were calculated by counting colony-forming units. A one-way analysis of variance (ANOVA) was applied to the data to assess the effect of different treatment techniques. Antimicrobial treatment of root canals caused a significant reduction of bacterial load in all groups. NaOCl irrigation eliminated E. faecalis most effectively. PDT alone was less effective compared to NaOCl irrigation and the combination of NaOCl irrigation and PDT. CFU levels recovered from the filling material after NaOCl irrigation of the root canals were 10fold higher compared to PDT and the combination of Na

FORMING THE PROFESSIONAL COMPETENCE OF THE FUTURE ENGLISH LANGUAGE TEACHERS OF PRIMARY SCHOOL USING ICT

Directory of Open Access Journals (Sweden)

Liudmyla H. Havrilova

2017-09-01

Full Text Available The paper is devoted to the results of experimental implementing ICT into forming the professional competence of future English teachers of primary school. Among the ways of using the electronic educational means offered by the authors there are: developing and using the educational and methodological simulator «Introduction to Interactive Communication» as a local electronic resource on English; implementing the distance learning courses «Practical English Grammar», «Linguistic Country Study» in future specialists’ professional training; work in the electronic services, mastering the programs of infographics during studying the discipline «Methodology of Teaching English». The analysis of the study results showed developing of students’ acmeological linguomethodological aspirations, increasing the motivation for learning, in particular the use of ICT tools in English classes, and proved the effectiveness of the chosen ways of forming the professional competence of future English teachers of primary school.

Quasi-experimental study designs series-paper 11: supporting the production and use of health systems research syntheses that draw on quasi-experimental study designs.

Science.gov (United States)

Lavis, John N; Bärnighausen, Till; El-Jardali, Fadi

2017-09-01

To describe the infrastructure available to support the production of policy-relevant health systems research syntheses, particularly those incorporating quasi-experimental evidence, and the tools available to support the use of these syntheses. Literature review. The general challenges associated with the available infrastructure include their sporadic nature or limited coverage of issues and countries, whereas the specific ones related to policy-relevant syntheses of quasi-experimental evidence include the lack of mechanism to register synthesis titles and scoping review protocols, the limited number of groups preparing user-friendly summaries, and the difficulty of finding quasi-experimental studies for inclusion in rapid syntheses and research syntheses more generally. Although some new tools have emerged in recent years, such as guidance workbooks and citizen briefs and panels, challenges related to using available tools to support the use of policy-relevant syntheses of quasi-experimental evidence arise from such studies potentially being harder for policymakers and stakeholders to commission and understand. Policymakers, stakeholders, and researchers need to expand the coverage and institutionalize the use of the available infrastructure and tools to support the use of health system research syntheses containing quasi-experimental evidence. Copyright © 2017 Elsevier Inc. All rights reserved.

Primary cultures of astrocytes

DEFF Research Database (Denmark)

Lange, Sofie C; Bak, Lasse Kristoffer; Waagepetersen, Helle S

2012-01-01

During the past few decades of astrocyte research it has become increasingly clear that astrocytes have taken a central position in all central nervous system activities. Much of our new understanding of astrocytes has been derived from studies conducted with primary cultures of astrocytes...... subsequently found in vivo. Nevertheless, primary cultures of astrocytes are an in vitro model that does not fully mimic the complex events occurring in vivo. Here we present an overview of the numerous contributions generated by the use of primary astrocyte cultures to uncover the diverse functions...... of astrocytes. Many of these discoveries would not have been possible to achieve without the use of astrocyte cultures. Additionally, we address and discuss the concerns that have been raised regarding the use of primary cultures of astrocytes as an experimental model system....

Portfolio as a learning strategy and a tool for assessment - a Danish experience

DEFF Research Database (Denmark)

Mogensen, Arne

A short presentation of some Danish expereriences using portfolio in maths teaching in primary and lower secondary schools as a learning strategy AND a tool for assessment.......A short presentation of some Danish expereriences using portfolio in maths teaching in primary and lower secondary schools as a learning strategy AND a tool for assessment....

Status of CONRAD, a nuclear reaction analysis tool

International Nuclear Information System (INIS)

Saint Jean, C. de; Habert, B.; Litaize, O.; Noguere, G.; Suteau, C.

2008-01-01

The development of a software tool (CONRAD) was initiated at CEA/Cadarache to give answers to various problems arising in the data analysis of nuclear reactions. This tool is then characterized by the handling of uncertainties from experimental values to covariance matrices for multi-group cross sections. An object oriented design was chosen allowing an easy interface with graphical tool for input/output data and being a natural framework for innovative nuclear models (Fission). The major achieved developments are a data model for describing channels, nuclear reactions, nuclear models and processes with interface to classical data formats, theoretical calculations for the resolved resonance range (Reich-Moore) and unresolved resonance range (Hauser-Feshbach, Gilbert-Cameron,...) with nuclear model parameters adjustment on experimental data sets and a Monte Carlo method based on conditional probabilities developed to calculate properly covariance matrices. The on-going developments deal with the experimental data description (covariance matrices) and the graphical user interface. (authors)

Experimental Object-Oriented Modelling

DEFF Research Database (Denmark)

Hansen, Klaus Marius

through, e.g., technical prototyping and active user involvement. We introduce and examine “experimental object-oriented modelling” as the intersection of these practices. The contributions of this thesis are expected to be within three perspectives on models and modelling in experimental system...... development: Grounding We develop an empirically based conceptualization of modelling and use of models in system development projects characterized by a high degree of uncertainty in requirements and point to implications for tools and techniques for modelling in such a setting. Techniques We introduce......This thesis examines object-oriented modelling in experimental system development. Object-oriented modelling aims at representing concepts and phenomena of a problem domain in terms of classes and objects. Experimental system development seeks active experimentation in a system development project...

Primary cardiac lymphoma: diagnostic tools and treatment challenges.

LENUS (Irish Health Repository)

Bambury, R

2011-03-01

Primary cardiac lymphoma (PCL) is a rare malignancy and the optimal treatment strategy remains uncertain. It appears to respond much better to systemic chemotherapy than to surgery and it should be considered in the differential diagnosis of all cardiac tumours before definitive management is undertaken. We report a case of this rare disorder treated successfully with a combination of rituximab and cyclophosphamide, adriamycin, vincristine and prednisolone. The patient developed recurrent unstable ventricular tachycardia (VT) post-chemotherapy secondary to extensive scarring at the tumour site. The tumour as well as the post-treatment scarring is well illustrated by cardiac magnetic resonance imaging highlighting its usefulness in this setting. An implantable cardioverter defibrillator (ICD) was placed. This is only the second case in the literature of PCL to have an ICD placed for recurrent VT. A brief literature review is included.

Preliminary experimental results of tungsten wire-array Z-pinches on primary test stand

Energy Technology Data Exchange (ETDEWEB)

Huang, Xian-Bin; Zhou, Shao-Tong; Dan, Jia-Kun; Ren, Xiao-Dong, E-mail: amosrxd@163.com; Wang, Kun-Lun; Zhang, Si-Qun; Li, Jing; Xu, Qiang; Cai, Hong-Chun; Duan, Shu-Chao; Ouyang, Kai; Chen, Guang-Hua; Ji, Ce; Wei, Bing; Feng, Shu-Ping; Wang, Meng; Xie, Wei-Ping; Deng, Jian-Jun [Key Laboratory of Pulsed Power, Institute of Fluid Physics, China Academy of Engineering Physics, P.O. Box 919-108, Mianyang, Sichuan 621999 (China); Zhou, Xiu-Wen; Yang, Yi [Research Center of Laser Fusion, China Academy of Engineering Physics, P.O. Box 919-987, Mianyang, Sichuan 621999 (China)

2015-07-15

The Primary Test Stand (PTS) developed at the China Academy of Engineering Physics is a 20 TW pulsed power driver, which can deliver a ∼10 MA, 70 ns rise-time (10%–90%) current to a short-circuit load and has important applications in Z-pinch driven inertial confinement fusion and high energy density physics. Preliminary results of tungsten wire-array Z-pinch experiments on PTS are presented. The load geometries investigated include 15-mm-tall cylindrical single and nested arrays with diameter ranging from 13 mm to 30 mm, consisting of 132–300 tungsten wires with 5–10 μm in diameter. Multiple diagnostics were fielded to characterize the x-ray radiation from wire-array Z pinches. The x-ray peak power (∼50 TW) and total radiated energy (∼500 kJ) were obtained from a single 20-mm-diam array with 80-ns stagnation time. The highest x-ray peak power up to 80 TW with 2.4 ns FWHM was achieved by using a nested array with 20-mm outer diameter, and the total x-ray energy from the nested array is comparable to that of single array. Implosion velocity estimated from the time-resolved image measurement exceeds 30 cm/μs. The detailed experimental results and other findings are presented and discussed.

Hyperuricemia in Childhood Primary Hypertension

OpenAIRE

Feig, Daniel I.; Johnson, Richard J.

2003-01-01

Experimental animal models suggest that uric acid might have a pathogenic role in the early development of primary hypertension. We hypothesized that serum uric acid is correlated with blood pressure in children with new-onset, untreated, primary hypertension. We evaluated 125 consecutive children referred to the Baylor Pediatric Renal Program for evaluation of hypertension. None of the subjects had previously been evaluated or treated for hypertension. The children ranged in age from 6 to 18...

A snapshot of the organization and provision of primary care in Turkey

Science.gov (United States)

2011-01-01

Background This WHO study aimed to support Turkey in its efforts to strengthen the primary care (PC) system by implementing the WHO Primary Care Evaluation Tool (PCET). This article provides an overview of the organization and provision of primary care in Turkey. Methods The WHO Primary Care Evaluation Tool was implemented in two provinces (Bolu and Eskişehir) in Turkey in 2007/08. The Tool consists of three parts: a national questionnaire concerning the organisation and financing of primary care; a questionnaire for family doctors; and a questionnaire for patients who visit a family health centre. Results Primary care has just recently become an official health policy priority with the introduction of a family medicine scheme. Although the supply of family doctors (FDs) has improved, they are geographically uneven distributed, and nationwide shortages of primary care staff remain. Coordination of care could be improved and quality control mechanisms were lacking. However, patients were very satisfied with the treatment by FDs. Conclusions The study provides an overview of the current state of PC in Turkey for two provinces with newly introduced family medicine, by using a structured approach to evaluate the essential functions of PC, including governance, financing, resource generation, as well as the characteristics of a "good" service delivery system (as being accessible, comprehensive, coordinated and continuous). PMID:21542904

Case study: to investigate blogging as an e-learning tool in post-primary schools

OpenAIRE

Conroy, Patty

2011-01-01

non-peer-reviewed The purpose of this case study is to investigate blogging as an e-learning tool. The era of e-learning has truly arrived. Educators have at their hands many free e-learning tools. It can be no longer the case of how information technology can be incorporated into the classroom but how effective each e-learning tool is to us as educators. Educators need to embrace e-learning combined with traditional teaching methods in order to engage and motivate our students most of who...

Mnemonic abilities of primary school children with delayed mental development.

Directory of Open Access Journals (Sweden)

Murafa S.V.

2015-07-01

Full Text Available This paper presents the results of research regarding the mnemonic abilities of primary school children with developmental delays. Empirical studies of impaired mental development offer an opportunity to elucidate the psychological mechanisms underlying the process of normal development and enable us to consider at a micro level the formation of mental processes in ontogeny, which would, under normal conditions, be nondescript and not always amenable to psychological analysis. The research addresses an experimental investigation of productivity and qualitative characteristics of mnemonic abilities among primary school students with developmental delays. V.D. Shadrikov’s Theory of Abilities, developed in a systemic approach framework, is the theoretical basis of the research. The method of deploying a memorization activity, as elaborated by V.D. Shadrikov and L.V. Cheremoshkina, was the investigation tool used. The sample included students in grades 1 to 4 between ages 7 to 12 and included a total of 100 children (66 boys and 34 girls. The control group of primary school students with typical development included 105 children (50 boys and 55 girls. The research consisted of several stages: a pilot study, experimental research (the test task was to memorize card #1; the basic task was to memorize cards #2 and #3; to reproduce cards #2 and #3; and to poll the students, mathematical data processing, and a description of the levels of mnemonic ability development among primary students with developmental delays. The following procedures were employed during statistical analysis: Spearman r3, Mann-Whitney U-test, Jonckheere-Terpstra test, and Kruskal-Wallis test. The structure of mnemonic abilities in primary schoolchildren with developmental delays was determined to vary according to the underdevelopment of their operational mechanisms. For example, memory functions are based on the use of inborn mechanisms, and a portion of children differ in the

Large scale experiments as a tool for numerical model development

DEFF Research Database (Denmark)

Kirkegaard, Jens; Hansen, Erik Asp; Fuchs, Jesper

2003-01-01

Experimental modelling is an important tool for study of hydrodynamic phenomena. The applicability of experiments can be expanded by the use of numerical models and experiments are important for documentation of the validity of numerical tools. In other cases numerical tools can be applied...

WORKING WITH DATA TABLES AND GRAPHS AT PRIMARY SCHOOL

Directory of Open Access Journals (Sweden)

Rumyana Y. Papancheva

2017-10-01

Full Text Available The article presents a model for developing data handling competencies at Primary school. The work is part of a larger research aiming at forming basic statistic literacy at early ages. Data analysis knowledge and skills are important part for the nowadays person. At Primary school, some basic skills for data handling must be developed. Working with data structured in tables and presented by graphs corresponds with the process of developing students’ digital skills. Experimental work was done at third grade of primary school in equipped with contemporary technologies learning environment. Some example tasks are presented and the results from the experimental work are analysed.

MATLAB platform for Monte Carlo planning and dosimetry experimental evaluation; Plataforma Matlab para planificacion Monte Carlo y evaluacion dosimetrica experimental

Energy Technology Data Exchange (ETDEWEB)

Baeza, J. A.; Ureba, A.; Jimenez-Ortega, E.; Pereira-Barbeiro, A. R.; Leal, A.

2013-07-01

A new platform for the full Monte Carlo planning and an independent experimental evaluation that it can be integrated into clinical practice. The tool has proved its usefulness and efficiency and now forms part of the flow of work of our research group, the tool used for the generation of results, which are to be suitably revised and are being published. This software is an effort of integration of numerous algorithms of image processing, along with planning optimization algorithms, allowing the process of MCTP planning from a single interface. In addition, becomes a flexible and accurate tool for the evaluation of experimental dosimetric data for the quality control of actual treatments. (Author)

Assembly tool design

International Nuclear Information System (INIS)

Kanamori, Naokazu; Nakahira, Masataka; Ohkawa, Yoshinao; Tada, Eisuke; Seki, Masahiro

1996-06-01

The reactor core of the International Thermonuclear Experimental Reactor (ITER) is assembled with a number of large and asymmetric components within a tight tolerance in order to assure the structural integrity for various loads and to provide the tritium confinement. In addition, the assembly procedure should be compatible with remote operation since the core structures will be activated by 14-MeV neutrons once it starts operation and thus personal access will be prohibited. Accordingly, the assembly procedure and tool design are quite essential and should be designed from the beginning to facilitate remote operation. According to the ITER Design Task Agreement, the Japan Atomic Energy Research Institute (JAERI) has performed design study to develop the assembly procedures and associated tool design for the ITER tokamak assembly. This report describes outlines of the assembly tools and the remaining issues obtained in this design study. (author)

An ultra-precision tool nanoindentation instrument for replication of single point diamond tool cutting edges

Science.gov (United States)

Cai, Yindi; Chen, Yuan-Liu; Xu, Malu; Shimizu, Yuki; Ito, So; Matsukuma, Hiraku; Gao, Wei

2018-05-01

Precision replication of the diamond tool cutting edge is required for non-destructive tool metrology. This paper presents an ultra-precision tool nanoindentation instrument designed and constructed for replication of the cutting edge of a single point diamond tool onto a selected soft metal workpiece by precisely indenting the tool cutting edge into the workpiece surface. The instrument has the ability to control the indentation depth with a nanometric resolution, enabling the replication of tool cutting edges with high precision. The motion of the diamond tool along the indentation direction is controlled by the piezoelectric actuator of a fast tool servo (FTS). An integrated capacitive sensor of the FTS is employed to detect the displacement of the diamond tool. The soft metal workpiece is attached to an aluminum cantilever whose deflection is monitored by another capacitive sensor, referred to as an outside capacitive sensor. The indentation force and depth can be accurately evaluated from the diamond tool displacement, the cantilever deflection and the cantilever spring constant. Experiments were carried out by replicating the cutting edge of a single point diamond tool with a nose radius of 2.0 mm on a copper workpiece surface. The profile of the replicated tool cutting edge was measured using an atomic force microscope (AFM). The effectiveness of the instrument in precision replication of diamond tool cutting edges is well-verified by the experimental results.

Filtration experiments of the KNK II primary sodium

International Nuclear Information System (INIS)

Stamm, H.H.

1987-01-01

The separated particles of the KNK primary sodium are a result of a normal corrosion rate by using ferritic and austenitic steels in sodium. Similar particle distributions and concentrations were found in primary circuits of other breeder plants (EBR-II et al). The experimental results of the particle concentration in the KNK primary sodium were lower than the theoretical calculation. Based on a corrosion rate of 0.5 micron/y for austenitic steels and a corrosion rate of 1.5 mg/square-cm y for a ferritic steel used in KNK as structure material an equilibrium particle concentration of 1.066 mg/kg Na was calculated. The experimental results of particle size are not in agreement with theoretical calculation of the BACCHUS code. (orig.)

Designing tools for oil exploration using nuclear modeling

Science.gov (United States)

Mauborgne, Marie-Laure; Allioli, Françoise; Manclossi, Mauro; Nicoletti, Luisa; Stoller, Chris; Evans, Mike

2017-09-01

When designing nuclear tools for oil exploration, one of the first steps is typically nuclear modeling for concept evaluation and initial characterization. Having an accurate model, including the availability of accurate cross sections, is essential to reduce or avoid time consuming and costly design iterations. During tool response characterization, modeling is benchmarked with experimental data and then used to complement and to expand the database to make it more detailed and inclusive of more measurement environments which are difficult or impossible to reproduce in the laboratory. We present comparisons of our modeling results obtained using the ENDF/B-VI and ENDF/B-VII cross section data bases, focusing on the response to a few elements found in the tool, borehole and subsurface formation. For neutron-induced inelastic and capture gamma ray spectroscopy, major obstacles may be caused by missing or inaccurate cross sections for essential materials. We show examples of the benchmarking of modeling results against experimental data obtained during tool characterization and discuss observed discrepancies.

The science writing tool

Science.gov (United States)

Schuhart, Arthur L.

This is a two-part dissertation. The primary part is the text of a science-based composition rhetoric and reader called The Science Writing Tool. This textbook has seven chapters dealing with topics in Science Rhetoric. Each chapter includes a variety of examples of science writing, discussion questions, writing assignments, and instructional resources. The purpose of this text is to introduce lower-division college science majors to the role that rhetoric and communication plays in the conduct of Science, and how these skills contribute to a successful career in Science. The text is designed as a "tool kit," for use by an instructor constructing a science-based composition course or a writing-intensive Science course. The second part of this part of this dissertation reports on student reactions to draft portions of The Science Writing Tool text. In this report, students of English Composition II at Northern Virginia Community College-Annandale were surveyed about their attitudes toward course materials and topics included. The findings were used to revise and expand The Science Writing Tool.

MODERN MEANS OF TEACHING A FOREIGN LANGUAGE IN PRIMARY SCHOOL

Directory of Open Access Journals (Sweden)

Olena Iaburova

2016-04-01

Full Text Available The article reveals the problems of teaching tools and resources used in the process of teaching foreign languages in primary school. The author gives the definition of the meanings “teaching resources”, “additional materials for teaching foreign languages», and their classification. The author pays attention to the fact that in the academic and upbringing process primary school teachers use different teaching resources in addition to the text-books as the basic means of teaching. That is why there is an evident reason for deep study of these kind materials, their classification. According to the way of presenting, teaching flash-cards and hand-outs as additional materials are pointed out. That is why the necessity of optimal and effective choice of these means of teaching depends on professional preparation of a teacher and teaching tools implementing in the academic process alongside with the text-books as the basic means of teaching foreign languages. The author notes that all these learning tools are not universal. They cannot completely replace a teacher or other learning tools. The author supports the idea of the need for optimum, deeply conscious and scientific approach to using additional educational resources in academic and upbringing process along with the textbook as the primary means of learning.

The Maastricht Ultrasound Shoulder pain trial (MUST: Ultrasound imaging as a diagnostic triage tool to improve management of patients with non-chronic shoulder pain in primary care

Directory of Open Access Journals (Sweden)

Cals Jochen WL

2011-07-01

Full Text Available Abstract Background Subacromial disorders are considered to be one of the most common pathologies affecting the shoulder. Optimal therapy for shoulder pain (SP in primary care is yet unknown, since clinical history and physical examination do not provide decisive evidence as to the patho-anatomical origin of the symptoms. Optimal decision strategies can be furthered by applying ultrasound imaging (US, an accurate method in diagnosing SP, demonstrating a clear relationship between diagnosis and available therapies. Yet, the clinical cost-effectiveness of applying US in the management of SP in primary care has not been studied. The aim of this paper is to describe the design and methods of a trial assessing the cost-effectiveness of ultrasound imaging as a diagnostic triage tool to improve management of primary care patients with non-chronic shoulder pain. Methods/Design This randomised controlled trial (RCT will involve 226 adult patients with suspected subacromial disorders recruited by general practitioners. During a Qualification period of two weeks, patients receive care as usual as advised by the Dutch College of General Practitioners, and patients are referred for US. Patients with insufficient improvement qualify for the RCT. These patients are then randomly assigned to the intervention or the control group. The therapies used in both groups are the same (corticosteroid injections, referral to a physiotherapist or orthopedic surgeon except that therapies used in the intervention group will be tailored based on the US results. Ultrasound diagnosed disorders include tendinopathy, calcific tendinitis, partial and full thickness tears, and subacromial bursitis. The primary outcome is patient-perceived recovery at 52 weeks, using the Global Perceived Effect questionnaire. Secondary outcomes are disease specific and generic quality of life, cost-effectiveness, and the adherence to the initial applied treatment. Outcome measures will be assessed

Randomized test of an implementation intention-based tool to reduce stress-induced eating.

Science.gov (United States)

O'Connor, Daryl B; Armitage, Christopher J; Ferguson, Eamonn

2015-06-01

Stress may indirectly contribute to disease (e.g. cardiovascular disease, cancer) by producing deleterious changes to diet. The purpose of this study was to test the effectiveness of a stress management support (SMS) tool to reduce stress-related unhealthy snacking and to promote stress-related healthy snacking. Participants were randomized to complete a SMS tool with instruction to link stressful situations with healthy snack alternatives (experimental) or a SMS tool without a linking instruction (control). On-line daily reports of stressors and snacking were completed for 7 days. Daily stressors were associated with unhealthy snack consumption in the control condition but not in the experimental condition. Participants highly motivated towards healthy eating consumed a greater number of healthy snacks in the experimental condition on stressful days compared to participants in the experimental condition with low and mean levels of motivation. This tool is an effective, theory driven, intervention that helps to protect against stress-induced high-calorie snack consumption.

Telemental health: responding to mandates for reform in primary healthcare.

Science.gov (United States)

Myers, Kathleen M; Lieberman, Daniel

2013-06-01

Telemental health (TMH) has established a niche as a feasible, acceptable, and effective service model to improve the mental healthcare and outcomes for individuals who cannot access traditional mental health services. The Accountability Care Act has mandated reforms in the structure, functioning, and financing of primary care that provide an opportunity for TMH to move into the mainstream healthcare system. By partnering with the Integrated Behavioral Healthcare Model, TMH offers a spectrum of tools to unite primary care physicians and mental health specialist in a mind-body view of patients' healthcare needs and to activate patients in their own care. TMH tools include video-teleconferencing to telecommute mental health specialists to the primary care setting to collaborate with a team in caring for patients' mental healthcare needs and to provide direct services to patients who are not progressing optimally with this collaborative model. Asynchronous tools include online therapies that offer an efficient first step to treatment for selected disorders such as depression and anxiety. Patients activate themselves in their care through portals that provide access to their healthcare information and Web sites that offer on-demand information and communication with a healthcare team. These synchronous and asynchronous TMH tools may move the site of mental healthcare from the clinic to the home. The evolving role of social media in facilitating communication among patients or with their healthcare team deserves further consideration as a tool to activate patients and provide more personalized care.

Test Review: Wechsler Preschool and Primary Scale of Intelligence-

Science.gov (United States)

Syeda, Maisha M.; Climie, Emma A.

2014-01-01

The "Wechsler Preschool and Primary Scale of Intelligence-Fourth Edition" (WPPSI-IV; Wechsler, 2012a, 2012b) is a comprehensive clinical tool, intended for assessing cognitive functioning among children aged 2 years 6 months through 7 years 7 months. Published by Pearson, the WPPSI-IV is an individually administered tool, to be used by…

Structures in the primary spectrum

International Nuclear Information System (INIS)

Kempa, J.; Knurenko, S.P.; Malecki, R.

2009-01-01

Structures in the energy spectrum of primary cosmic rays at the 'knee' region and for energies higher than 1 EeV are obtained through studying extensive air showers (EAS). The main problem of the research is the fact that we work in the ranges of highly fluctuating parameters used to obtain the primary energy spectrum. In this paper the log-normal distribution for the error function has been used in convolution with the power spectrum to explain the Yakutsk experimental data. Similar results have been obtained for the gamma distribution as the error function. Using the power law primary spectrum in the energy region around 10 19 eV we will argue that the primary Yakutsk spectrum is overestimated. In the best case this overestimation is not less than 42%.

General practice ethnicity data: evaluation of a tool

Directory of Open Access Journals (Sweden)

Neuwelt P

2014-03-01

Full Text Available INTRODUCTION: There is evidence that the collection of ethnicity data in New Zealand primary care is variable and that data recording in practices does not always align with the procedures outlined in the Ethnicity Data Protocols for the Health and Disability Sector. In 2010, The Ministry of Health funded the development of a tool to audit the collection of ethnicity data in primary care. The aim of this study was to pilot the Ethnicity Data Audit Tool (EAT in general practice. The goal was to evaluate the tool and identify recommendations for its improvement. METHODS: Eight general practices in the Waitemata District Health Board region participated in the EAT pilot. Feedback about the pilot process was gathered by questionnaires and interviews, to gain an understanding of practices’ experiences in using the tool. Questionnaire and interview data were analysed using a simple analytical framework and a general inductive method. FINDINGS: General practice receptionists, practice managers and general practitioners participated in the pilot. Participants found the pilot process challenging but enlightening. The majority felt that the EAT was a useful quality improvement tool for handling patient ethnicity data. Larger practices were the most positive about the tool. CONCLUSION: The findings suggest that, with minor improvements to the toolkit, the EAT has the potential to lead to significant improvements in the quality of ethnicity data collection and recording in New Zealand general practices. Other system-level factors also need to be addressed.

Collaborative Digital Games as Mediation Tool to Foster Intercultural Integration in Primary Dutch Schools

NARCIS (Netherlands)

de la Hera Conde-Pumpido, T.|info:eu-repo/dai/nl/331869063; Paz Aléncar, Amanda

2015-01-01

The use of digital games has found to be an effective tool to reinforce teaching/learning practices. Several studies have already shown the benefits of the use of digital games in educational contexts. However, most of these studies are focused on how digital games can be used as a mediation tool in

Scratch as a Computational Modelling Tool for Teaching Physics

Science.gov (United States)

Lopez, Victor; Hernandez, Maria Isabel

2015-01-01

The Scratch online authoring tool, which features a simple programming language that has been adapted to primary and secondary students, is being used more and more in schools as it offers students and teachers the opportunity to use a tool to build scientific models and evaluate their behaviour, just as can be done with computational modelling…

Experimental study on air ingress during a primary pipe rupture accident with a graphite reactor core simulator

International Nuclear Information System (INIS)

Takeda, Tetsuaki; Hishida, Makoto; Baba, Shinichi

1991-11-01

When a primary coolant pipe of a High Temperature Gas Cooled Reactor (HTGR) ruptures, helium gas in the reactor core blows out into the container, and the primary cooling system reduces the pressure. After the pressures are balanced between the reactor and the container, air is expected to enter into the reactor core from the breach. It seems to be probable that the graphite structures is oxidized by air. Hence, it is necessary to investigate the air ingress process and the behavior of the generating gases by the oxidation reactions. The previous experimental study is performed on the molecular diffusion and natural convection of the two component gas mixtures using a test model simulating simply the reactor. Objective of the study was to investigate the air ingress process during the early stage of the primary pipe rupture accident. However, since the model did not have any kind of graphite components, the reaction between graphite and oxygen was not simulated. The present model includes the reactor core and the high temperature plenum simulators made of graphite. The major results obtained in the present study are summarized in the followings: (1) The air ingress process with graphite oxidation reaction is similar to that without the reaction qualitatively. (2) When the reactor core simulator is maintained at low temperatures (lower than 450degC), the initiation time of the natural circulation of air is almost equal to that of the natural circulation of nitrogen. On the other hand, when the temperature of the reactor core simulator is high (more than 500degC), the initiation time of the natural circulation of air is earlier than that of nitrogen. (3) When the temperature of the reactor core simulator is higher than 600degC, oxygen is almost dissipated by the graphite structures. When the temperature of the reactor core simulator is below 700degC, carbon dioxide mainly is generated by the oxidation reactions. (author)

Preliminary analysis in support to the experimental activities on the mixing process in the pressurizer of a small modular reactor integrated primary system

Energy Technology Data Exchange (ETDEWEB)

Nascimento, Samira R.V.; Lira, Carlos A.B.O.; Bezerra, Jair L.; Silva, Mario A.B.; Silva, Willdauany C.F., E-mail: samiraruana@gmail.com [Universidade Federal de Pernambuco (DEN/UFPE), Recife, PE (Brazil). Departamento de Energia Nuclear; Lapa, Celso M.F., E-mail: lapa@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Lima, Fernando R.A., E-mail: falima@crcn.gov.br [Centro Regional de Ciencias Nucleares (CRCN/CNEN-NE), Recife, PE (Brazil); Otero, Maria E.M.; Hernandez, Carlos R.G., E-mail: mmontesi@instec.cu [Department of Nuclear Engineering, InSTEC/CUBA, Higher Institute of Technology and Applied Science, La Habana (Cuba)

2015-07-01

Nowadays, there is a renewed interest in the development of advanced/innovative small and medium sized modular reactors (SMRs). The SMRs are variants of the Generation IV systems and usually have attractive characteristics of simplicity, enhanced safety and require limited financial resources. The concept of the integrated primary system reactor (IPSR) is characterized by the inclusion of the entire primary system within a single pressure vessel, including the steam generator and pressurizer. The pressurizer is located within the reactor vessel top, this configuration involves changes on the techniques and is necessary investigate the boron mixing. The present work represents a contribution to the design of an experimental facility planned to provide data relevant for the mixing phenomena in the pressurizer of a compact modular reactor. In particular, in order to evaluate the boron concentration in the surge orifices to simulate the in-surge and out-surge in a facility, scaled 1:200, respect to the ¼ of the pressurizer. The facility behavior studied from one inlet and one outlet of the test section with represent one in-surge e one out-surge the pressurizer of a small modular reactor integrated primary system. (author)

FEM-DEM coupling simulations of the tool wear characteristics in prestressed machining superalloy

Directory of Open Access Journals (Sweden)

Ruitao Peng

2016-01-01

Full Text Available Due to the complicated contact loading at the tool-chip interface, ceramic tool wear in prestressed machining superalloy is rare difficult to evaluate only by experimental approaches. This study aims to develop a methodology to predict the tool wear evolution by using combined FEM and DEM numerical simulations. Firstly, a finite element model for prestressed cutting is established, subsequently a discrete element model to describe the tool-chip behaviour is established based on the obtained boundary conditions by FEM simulations, finally, simulated results are experimentally validated. The predicted tool wear results show nice agreement with experiments, the simulation indicates that, within a certain range, higher cutting speed effectively results in slighter wear of Sialon ceramic tools, and deeper depth of cut leads to more serious tool wear.

Experimental techniques and measurement accuracies

International Nuclear Information System (INIS)

Bennett, E.F.; Yule, T.J.; DiIorio, G.; Nakamura, T.; Maekawa, H.

1985-02-01

A brief description of the experimental tools available for fusion neutronics experiments is given. Attention is paid to error estimates mainly for the measurement of tritium breeding ratio in simulated blankets using various techniques

Transfection in Primary Cultured Neuronal Cells.

Science.gov (United States)

Marwick, Katie F M; Hardingham, Giles E

2017-01-01

Transfection allows the introduction of foreign nucleic acid into eukaryotic cells. It is an important tool in understanding the roles of NMDARs in neurons. Here, we describe using lipofection-mediated transfection to introduce cDNA encoding NMDAR subunits into postmitotic rodent primary cortical neurons maintained in culture.

[Primary psoas abscess in a young healthy male

DEFF Research Database (Denmark)

Nassehi, D.; Galbo, H.; Skovsgaard, F.

2008-01-01

and North America. It is primarily seen in young men, and the classical symptom-triad is: fever, back pain, and limpness. The golden standard diagnostic tool is computed tomography, and treatment involves appropriate antibiotics, which can be combined with percutaneous drainage Udgivelsesdato: 2008/11/24......A young male saw his general practitioner because of lower back pain, limpness, nightly sweating, subfebrilia, and weight loss. Further diagnostics showed that he had a primary psoas abscess. Psoas abscesses are categorized as primary and secondary. Primary psoas abscess is a rare disease in Europe...

A new approach for primary overloads allowance in ratcheting evaluation

International Nuclear Information System (INIS)

Cabrillat, M.T.; Gatt, J.M.; Lejeail, Y.

1995-01-01

Seismic loading must be taken into account in ratchetting design analysis. In LMFBR structures it mainly produces primary overloads, which are characterised by severe magnitudes but a generally low number of occurrences. Other cases of several primary overloads can also observed in pipes during emptying operations for instance. In the RCC-MR design code rule, the maximum primary stress supported by a structure is considered as permanent. No allowance is made for temporary load. Experimental ratchetting tests conducted on different structures with and without overloads clearly point out that temporary overloads lead to less ratchetting effect. A method using the RCC-MR efficiency diagram framework is proposed. A general theoretical approach allows to extend its field of application of various cases of primary loading: constant or null primary loading or overloads. Experimental results are then used to check the validity of this new approach. (author). 2 refs., 2 figs., 2 tabs

What influences on demonstration experimental work in chemistry classroom?

OpenAIRE

Logar, Ana; Ferk Savec, Vesna

2016-01-01

Teachers and researchers agree that experimental work has a crucial role in teaching and learning of science. The article presents results of a qualitative investigation dealing with factors that influence on the efficiency of primary school students` experimental work in chemistry classroom. The sample consisted of 9 chemistry teachers and 141 randomly selected primary school students (age 13-14 years). Based on the research results a model for effective planning and integration of students`...

Interactive Electronic Decision Trees for the Integrated Primary Care Management of Febrile Children in Low Resource Settings - Review of existing tools.

Science.gov (United States)

Keitel, Kristina; D'Acremont, Valérie

2018-04-20

The lack of effective, integrated diagnostic tools pose a major challenge to the primary care management of febrile childhood illnesses. These limitations are especially evident in low-resource settings and are often inappropriately compensated by antimicrobial over-prescription. Interactive electronic decision trees (IEDTs) have the potential to close these gaps: guiding antibiotic use and better identifying serious disease. This narrative review summarizes existing IEDTs, to provide an overview of their degree of validation, as well as to identify gaps in current knowledge and prospects for future innovation. Structured literature review in PubMed and Embase complemented by google search and contact with developers. Six integrated IEDTs were identified: three (eIMCI, REC, and Bangladesh digital IMCI) based on Integrated Management of Childhood Illnesses (IMCI); four (SL eCCM, MEDSINC, e-iCCM, and D-Tree eCCM) on Integrated Community Case Management (iCCM); two (ALMANACH, MSFeCARE) with a modified IMCI content; and one (ePOCT) that integrates novel content with biomarker testing. The types of publications and evaluation studies varied greatly: the content and evidence-base was published for two (ALMANACH and ePOCT), ALMANACH and ePOCT were validated in efficacy studies. Other types of evaluations, such as compliance, acceptability were available for D-Tree eCCM, eIMCI, ALMANACH. Several evaluations are still ongoing. Future prospects include conducting effectiveness and impact studies using data gathered through larger studies to adapt the medical content to local epidemiology, improving the software and sensors, and Assessing factors that influence compliance and scale-up. IEDTs are valuable tools that have the potential to improve management of febrile children in primary care and increase the rational use of diagnostics and antimicrobials. Next steps in the evidence pathway should be larger effectiveness and impact studies (including cost analysis) and

Primary experimental results of wire-array Z-pinches on PTS

Energy Technology Data Exchange (ETDEWEB)

Huang, X. B., E-mail: caephxb2003@aliyun.com; Zhou, S. T., E-mail: caephxb2003@aliyun.com; Ren, X. D., E-mail: caephxb2003@aliyun.com; Dan, J. K., E-mail: caephxb2003@aliyun.com; Wang, K. L., E-mail: caephxb2003@aliyun.com; Zhang, S. Q., E-mail: caephxb2003@aliyun.com; Li, J., E-mail: caephxb2003@aliyun.com; Xu, Q., E-mail: caephxb2003@aliyun.com; Cai, H. C., E-mail: caephxb2003@aliyun.com; Duan, S. C., E-mail: caephxb2003@aliyun.com; Ouyang, K., E-mail: caephxb2003@aliyun.com; Chen, G. H., E-mail: caephxb2003@aliyun.com; Ji, C., E-mail: caephxb2003@aliyun.com; Wang, M., E-mail: caephxb2003@aliyun.com; Feng, S. P., E-mail: caephxb2003@aliyun.com; Yang, L. B., E-mail: caephxb2003@aliyun.com; Xie, W. P., E-mail: caephxb2003@aliyun.com; Deng, J. J., E-mail: caephxb2003@aliyun.com [Key Lab of Pulsed Power, Institute of Fluid Physics, CAEP, P.O. Box 919-108, Mianyang, Sichuan 621999 (China)

2014-12-15

The Primary Test Stand (PTS) developed at the China Academy of Engineering Physics is a multiterawatt pulsed power driver, which can deliver a ∼10 MA, 70 ns rise-time (10%-90%) current to a short circuit load and has important applications in Z-pinch driven inertial confinement fusion and high energy density physics. In this paper, primary results of tungsten wire-array Z-pinch experiments on PTS are presented. The load geometries investigated include 15-mm-tall cylindrical single and nested arrays with diameter ranging from 14.4-26.4 mm, and consisting of 132∼276 tungsten wires with 5∼10 μm in diameter. Multiple diagnostics were fielded to determine the characteristics of x-ray radiations and to obtain self-emitting images of imploding plasmas. X-ray power up to 80 TW with ∼3 ns FWMH is achieved by using nested wire arrays. The total x-ray energy exceeds 500 kJ and the peak radiation temperature is about 150 eV. Typical velocity of imploding plasmas goes around 3∼5×10{sup 7} cm/s and the radial convergence ratio is between 10 and 20.

[When and how to report suspected child abuse to child protective services. Construction and evaluation of a specific support tool for primary care physicians].

Science.gov (United States)

Michaud, E; Fleury, J; Launay, E; Pendezec, G; Gras-Le-Guen, C; Vabres, N

2017-11-01

The aim of this study was to create a specific tool and evaluate its impact on the knowledge of primary care physicians (PCPs) in reporting child abuse to child protective services (CPS). Prospective "before/after" study assessing the knowledge of general practitioners (GPs) registered at the medical board in a French administrative area through anonymous questionnaires. The tool was adapted from the guidelines published in 2014 by the French Health authorities. The main criterion was the median score (/100) calculated for each questionnaire before (Q1) and after (Q2) the dissemination of the tool. These median scores were compared and associations between scores and some PCPs' characteristics were tested through multiple linear regression. A total of 279 GPs answered the first questionnaire (Q1) and 172 answered the second (Q2). PCPs who answered were mainly women (68% and 74%), were between 30 and 50 years old (61% and 66%), practiced in association with other physicians (82% and 84), and had 15-30% children in their patient population. For Q1, the general median was 65 [IQR: 40-81] versus 82 [IQR: 71-91] for Q2 (P<0.001). The PCPs' characteristics leading to significant variations in the scores for Q1 were age older than 50 years, being female, and having been trained in diagnosis and management of child abuse, with the β coefficient at -16.4 [95% CI: -31.1; -1.69], +8.93 [95% CI: 2.58; 15.27] and +12 [95% CI: 6.33; 17.73], respectively. This study confirms the significant impact of this new tool on PCPs' knowledge concerning reporting suspected child abuse to the CPS. Wider dissemination of this tool could increase PCPs' awareness and comprehension of when and how to make a report to the CPS. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Spatial memory: Theoretical basis and comparative review on experimental methods in rodents.

Science.gov (United States)

Paul, Carrillo-Mora; Magda, Giordano; Abel, Santamaría

2009-11-05

The assessment of learning and memory in animal models has been widely employed in scientific research for a long time. Among these models, those representing diseases with primary processes of affected memory - such as amnesia, dementia, brain aging, etc. - studies dealing with the toxic effects of specific drugs, and other exploring neurodevelopment, trauma, epilepsy and neuropsychiatric disorders, are often called on to employ these tools. There is a diversity of experimental methods assessing animal learning and memory skills. Overall, mazes are the devices mostly used today to test memory in rodents; there are several types of them, but their real usefulness, advantages and applications remain to be fully established and depend on the particular variant selected by the experimenter. The aims of the present article are first, to briefly review the accumulated knowledge in regard to spatial memory tasks; second, to bring the reader information on the different types of rodent mazes available to test spatial memory; and third, to elucidate the usefulness and limitations of each of these devices.

A patient self-assessment tool for cardiac rehabilitation.

Science.gov (United States)

Phelan, C; Finnell, M D; Mottla, K A

1989-01-01

A patient self-assessment tool was designed, tested, and implemented to promote cardiac-specific data collection, based on Gordon's Functional Health Patterns, to maximize patient/family involvement in determining a plan of care, and to streamline primary nurses' documentation requirements. Retrospective and concurrent chart reviews provided data for quality assurance monitoring. The results of the monitoring demonstrated that the self-assessment tool markedly improved the patient-specific data base.

INTELLECTUAL PROPERTY RIGHTS ISSUES FOR RESEARCH TOOLS IN BIOTECHNOLOGY RESEARCH

Directory of Open Access Journals (Sweden)

Rekha Chaturvedi

2015-09-01

Full Text Available The research tools refer to the resources researchers need to use in experimental work. In Biotechnology, these can include cell lines, monoclonal antibodies, reagents, animal models, growth factors, combinatorial chemistry libraries, drug and drug targets, clones and cloning tools (such as PCR, method, laboratory equipment and machines, database and computer software. Research tools therefore serve as basis for upstream research to improve the present product or process. There are several challenges in the way of using patented research tools. IP issues with regard to research tools are important and may sometime pose hindrance for researchers. Hence in the case of patented research tools, IPR issues can compose a major hurdle for technology development. In majority instances research tools are permitted through MTAs for academic research and for imparting education. TRIPS provides a provision for exception to patent rights for experimental use of patented technology in scientific research and several countries including India have included this provision in their patent legislation. For commercially important work, licensing of research tools can be based on royalty or one time lump sum payment. Some patent owners of important high-end research tools for development of platform technology create problems in licensing which can impede research. Usually cost of a commercially available research tool is built up in its price.

Designing tools for oil exploration using nuclear modeling

Directory of Open Access Journals (Sweden)

Mauborgne Marie-Laure

2017-01-01

Full Text Available When designing nuclear tools for oil exploration, one of the first steps is typically nuclear modeling for concept evaluation and initial characterization. Having an accurate model, including the availability of accurate cross sections, is essential to reduce or avoid time consuming and costly design iterations. During tool response characterization, modeling is benchmarked with experimental data and then used to complement and to expand the database to make it more detailed and inclusive of more measurement environments which are difficult or impossible to reproduce in the laboratory. We present comparisons of our modeling results obtained using the ENDF/B-VI and ENDF/B-VII cross section data bases, focusing on the response to a few elements found in the tool, borehole and subsurface formation. For neutron-induced inelastic and capture gamma ray spectroscopy, major obstacles may be caused by missing or inaccurate cross sections for essential materials. We show examples of the benchmarking of modeling results against experimental data obtained during tool characterization and discuss observed discrepancies.

Towards an Experimental Framework for Measuring Usability of Model-Driven Tools

NARCIS (Netherlands)

Panach, Jose Ignacio; Condori-Fernandez, Nelly; Baar, Arthur; Vos, Tanja; Romeu, Ignacio; Pastor, Oscar; Campos, Pedro; Graham, Nicholas; Jorge, Joaquim; Nunes, Nuno; Palanque, Philippe; Winckler, Marco

2011-01-01

According to the Model-Driven Development (MDD) paradigm, analysts can substantially improve the software development process concentrating their efforts on a conceptual model, which can be transformed into code by means of transformation rules applied by a model compiler. However, MDD tools are not

Evaluation of the effect of an audit and feedback reporting tool on screening participation: The Primary Care Screening Activity Report (PCSAR).

Science.gov (United States)

Jonah, Leigh; Pefoyo, Anna Kone; Lee, Alex; Hader, Joanne; Strasberg, Suzanne; Kupets, Rachel; Chiarelli, Anna M; Tinmouth, Jill

2017-03-01

Participation in cancer screening is critical to its effectiveness in reducing the burden of cancer. The Primary Care Screening Activity Report (PCSAR), an electronic report, was developed as an innovative audit and feedback tool to increase screening participation in Ontario's cancer screening programs. This study aims to assess its impact on patient screening participation. This study used a retrospective cohort design to evaluate the effectiveness of the 2014 PCSAR on screening participation in Ontario's three screening programs (breast, cervix and colorectal). The 3 cohorts comprised all participants eligible for each of the programs enrolled with a primary care physician in Ontario. Two exposures were evaluated for each cohort: enrollment with a physician who was registered to receive the PCSAR and enrollment with a registered physician who also logged into the PCSAR. Logistic regression modelling was used to assess the magnitude of the effect of PCSAR on participation, adjusting for participant and physician characteristics. Across all three screening programs, 63% of eligible physicians registered to receive the PCSAR and 38% of those registered logged-in to view it. Patients of physicians who registered were significantly more likely to participate in screening, with odds ratios ranging from 1.06 [1.04;1.09] to 1.15 [1.12;1.19]. The adjusted odds ratios associated with PCSAR log-in were 1.07 [1.03;1.12] to 1.18 [1.14;1.22] across all screening programs. Implementation of the PCSAR was associated with a small increase in screening participation. The PCSAR appears to be modestly effective in assisting primary care physicians in optimizing cancer screening participation among their patients. Copyright © 2017 Elsevier Inc. All rights reserved.

Experimental verification of a deep drawing tool system for adaptive blank holder pressure distribution

DEFF Research Database (Denmark)

Tommerup, Søren; Endelt, Benny Ørtoft

2012-01-01

In deep drawing, the strain path in the blank during the forming process can be significantly affected by application of temporal and spatial variation of the blank holder force. In this study, an active tool system capable of controlling the distribution of the blank holder force is presented...... which can be integrated into existing stacked deep drawing tools without need for modification of the press. A working system is presented consisting of a controller, designated volume displacement cavity pressure supply units and a shimming plate. It is applied to the deep drawing of a rectangular...... to the conventional shimming method using paper or metal shims between the tool plates. The tool system’s ability to influence the material flow is investigated by performing a series of deep drawing experiments. Eight different cavity pressure schemes are applied during the punch stroke and the scheme’s effects...

Knockout reactions: experimental aspects

Energy Technology Data Exchange (ETDEWEB)

Cortina Gil, D. [Santiago de Compostela Univ. (Spain)

2007-07-01

The availability of radioactive beams has given rise to intense activity in the field of direct reactions. The removal of one(two)-nucleon (referred to as nucleon knockout in this text) from a fast exotic projectile has been extensively investigated. This lecture provides a general overview of the experimental results achieved using this technique. The sensitivity of the method to different experimental aspects is illustrated with a few examples. Special attention is given to the application of nucleon-knockout reactions as a general purpose spectroscopic tool. (author)

Knockout reactions: experimental aspects

International Nuclear Information System (INIS)

Cortina Gil, D.

2007-01-01

The availability of radioactive beams has given rise to intense activity in the field of direct reactions. The removal of one(two)-nucleon (referred to as nucleon knockout in this text) from a fast exotic projectile has been extensively investigated. This lecture provides a general overview of the experimental results achieved using this technique. The sensitivity of the method to different experimental aspects is illustrated with a few examples. Special attention is given to the application of nucleon-knockout reactions as a general purpose spectroscopic tool. (author)

Primary photosynthetic processes: from supercomplex to leaf

NARCIS (Netherlands)

Broess, K.

2009-01-01

This thesis describes fluorescence spectroscopy experiments on photosynthetic complexes that cover the primary photosynthetic processes, from the absorption of light by photosynthetic pigments to a charge separation (CS) in the reaction center (RC). Fluorescence spectroscopy is a useful tool in

Prediction and Control of Cutting Tool Vibration in Cnc Lathe with Anova and Ann

Directory of Open Access Journals (Sweden)

S. S. Abuthakeer

2011-06-01

Full Text Available Machining is a complex process in which many variables can deleterious the desired results. Among them, cutting tool vibration is the most critical phenomenon which influences dimensional precision of the components machined, functional behavior of the machine tools and life of the cutting tool. In a machining operation, the cutting tool vibrations are mainly influenced by cutting parameters like cutting speed, depth of cut and tool feed rate. In this work, the cutting tool vibrations are controlled using a damping pad made of Neoprene. Experiments were conducted in a CNC lathe where the tool holder is supported with and without damping pad. The cutting tool vibration signals were collected through a data acquisition system supported by LabVIEW software. To increase the buoyancy and reliability of the experiments, a full factorial experimental design was used. Experimental data collected were tested with analysis of variance (ANOVA to understand the influences of the cutting parameters. Empirical models have been developed using analysis of variance (ANOVA. Experimental studies and data analysis have been performed to validate the proposed damping system. Multilayer perceptron neural network model has been constructed with feed forward back-propagation algorithm using the acquired data. On the completion of the experimental test ANN is used to validate the results obtained and also to predict the behavior of the system under any cutting condition within the operating range. The onsite tests show that the proposed system reduces the vibration of cutting tool to a greater extend.

π Scope: python based scientific workbench with visualization tool for MDSplus data

Science.gov (United States)

Shiraiwa, S.

2014-10-01

π Scope is a python based scientific data analysis and visualization tool constructed on wxPython and Matplotlib. Although it is designed to be a generic tool, the primary motivation for developing the new software is 1) to provide an updated tool to browse MDSplus data, with functionalities beyond dwscope and jScope, and 2) to provide a universal foundation to construct interface tools to perform computer simulation and modeling for Alcator C-Mod. It provides many features to visualize MDSplus data during tokamak experiments including overplotting different signals and discharges, various plot types (line, contour, image, etc.), in-panel data analysis using python scripts, and publication quality graphics generation. Additionally, the logic to produce multi-panel plots is designed to be backward compatible with dwscope, enabling smooth migration for dwscope users. πScope uses multi-threading to reduce data transfer latency, and its object-oriented design makes it easy to modify and expand while the open source nature allows portability. A built-in tree data browser allows a user to approach the data structure both from a GUI and a script, enabling relatively complex data analysis workflow to be built quickly. As an example, an IDL-based interface to perform GENRAY/CQL3D simulations was ported on πScope, thus allowing LHCD simulation to be run between-shot using C-Mod experimental profiles. This workflow is being used to generate a large database to develop a LHCD actuator model for the plasma control system. Supported by USDoE Award DE-FC02-99ER54512.

Tools for building virtual laboratories

International Nuclear Information System (INIS)

Agarwal, Debora; Johnston, William E.; Loken, Stewart; Tierney, Brian

1996-01-01

There is increasing interest in making unique research facilities facilities accessible on the Internet. Computer systems, scientific databases and experimental apparatus can be used by international collaborations of scientists using high-speed networks and advanced software tools to support collaboration. We are building tools including video conferencing and electronic white boards that are being used to create examples of virtual laboratories. This paper describes two pilot projects which provide testbeds for the tools. The first is a virtual laboratory project providing remote access to LBNL's Advanced Light Source. The second is the Multidimensional Applications and Gigabit internet work Consortium (MAGIC) testbed which has been established to develop a very high-speed, wide-are network to deliver realtime data at gigabit-per-second rates. (author)

Online Experimentation in Education and Training

Directory of Open Access Journals (Sweden)

Maria Teresa Restivo

2014-03-01

Full Text Available The increasing use of emergent technologies in industry, medicine, research, training and education attests to the relevance of their integration in teaching/learning approaches. Online experimentation comprises remote and virtual experimentation also supported and complemented by other online tools that incorporate necessarily the use of emergent technologies. The present work synthesizes the final outcomes of a project aiming to develop, use and disseminate Online Experimentation, funded by the Calouste Gulbenkian Foundation. Some application examples are given to illustrate the use of online experimentation on different contexts, such as secondary and higher education (STEM, lifelong learning or industrial training.

Modelling of Tool Wear and Residual Stress during Machining of AISI H13 Tool Steel

Science.gov (United States)

Outeiro, José C.; Umbrello, Domenico; Pina, José C.; Rizzuti, Stefania

2007-05-01

Residual stresses can enhance or impair the ability of a component to withstand loading conditions in service (fatigue, creep, stress corrosion cracking, etc.), depending on their nature: compressive or tensile, respectively. This poses enormous problems in structural assembly as this affects the structural integrity of the whole part. In addition, tool wear issues are of critical importance in manufacturing since these affect component quality, tool life and machining cost. Therefore, prediction and control of both tool wear and the residual stresses in machining are absolutely necessary. In this work, a two-dimensional Finite Element model using an implicit Lagrangian formulation with an automatic remeshing was applied to simulate the orthogonal cutting process of AISI H13 tool steel. To validate such model the predicted and experimentally measured chip geometry, cutting forces, temperatures, tool wear and residual stresses on the machined affected layers were compared. The proposed FE model allowed us to investigate the influence of tool geometry, cutting regime parameters and tool wear on residual stress distribution in the machined surface and subsurface of AISI H13 tool steel. The obtained results permit to conclude that in order to reduce the magnitude of surface residual stresses, the cutting speed should be increased, the uncut chip thickness (or feed) should be reduced and machining with honed tools having large cutting edge radii produce better results than chamfered tools. Moreover, increasing tool wear increases the magnitude of surface residual stresses.

Evaluating the reliability of an injury prevention screening tool: Test-retest study.

Science.gov (United States)

Gittelman, Michael A; Kincaid, Madeline; Denny, Sarah; Wervey Arnold, Melissa; FitzGerald, Michael; Carle, Adam C; Mara, Constance A

2016-10-01

A standardized injury prevention (IP) screening tool can identify family risks and allow pediatricians to address behaviors. To assess behavior changes on later screens, the tool must be reliable for an individual and ideally between household members. Little research has examined the reliability of safety screening tool questions. This study utilized test-retest reliability of parent responses on an existing IP questionnaire and also compared responses between household parents. Investigators recruited parents of children 0 to 1 year of age during admission to a tertiary care children's hospital. When both parents were present, one was chosen as the "primary" respondent. Primary respondents completed the 30-question IP screening tool after consent, and they were re-screened approximately 4 hours later to test individual reliability. The "second" parent, when present, only completed the tool once. All participants received a 10-dollar gift card. Cohen's Kappa was used to estimate test-retest reliability and inter-rater agreement. Standard test-retest criteria consider Kappa values: 0.0 to 0.40 poor to fair, 0.41 to 0.60 moderate, 0.61 to 0.80 substantial, and 0.81 to 1.00 as almost perfect reliability. One hundred five families participated, with five lost to follow-up. Thirty-two (30.5%) parent dyads completed the tool. Primary respondents were generally mothers (88%) and Caucasian (72%). Test-retest of the primary respondents showed their responses to be almost perfect; average 0.82 (SD = 0.13, range 0.49-1.00). Seventeen questions had almost perfect test-retest reliability and 11 had substantial reliability. However, inter-rater agreement between household members for 12 objective questions showed little agreement between responses; inter-rater agreement averaged 0.35 (SD = 0.34, range -0.19-1.00). One question had almost perfect inter-rater agreement and two had substantial inter-rater agreement. The IP screening tool used by a single individual had excellent

Laser additive manufacturing of multimaterial tool inserts: a simulation-based optimization study

DEFF Research Database (Denmark)

Mohanty, Sankhya; Hattel, Jesper Henri

2017-01-01

laser additive manufacturing. The physical handling of multi-material in a SLM setup continues to be a primary challenge along with the selection of process parameters/plan to achieve the desired results – both challenges requiring considerable experimental undertakings. Consequently, numerical process...... which a layer of steel has been deposited using cold-spraying technique, such as to protect the microstructure of Ni during selective laser melting. The process modelled thus entails additively manufacturing a steel tool insert around the multi-material specimen with a goal of achieving a dense product......Selective laser melting is fast evolving into an industrially applicable manufacturing process. While components produced from high-value materials, such as Ti6Al4V and Inconel 718 alloys, are already being produced, the processing of multi-material components still remains to be achieved by using...

The Healthy Primary School of the Future: study protocol of a quasi-experimental study.

Science.gov (United States)

Willeboordse, M; Jansen, M W; van den Heijkant, S N; Simons, A; Winkens, B; de Groot, R H M; Bartelink, N; Kremers, S P; van Assema, P; Savelberg, H H; de Neubourg, E; Borghans, L; Schils, T; Coppens, K M; Dietvorst, R; Ten Hoopen, R; Coomans, F; Klosse, S; Conjaerts, M H J; Oosterhoff, M; Joore, M A; Ferreira, I; Muris, P; Bosma, H; Toppenberg, H L; van Schayck, C P

2016-07-26

Unhealthy lifestyles in early childhood are a major global health challenge. These lifestyles often persist from generation to generation and contribute to a vicious cycle of health-related and social problems. This design article presents a study evaluating the effects of two novel healthy school interventions. The main outcome measure will be changes in children's body mass index (BMI). In addition, lifestyle behaviours, academic achievement, child well-being, socio-economic differences, and societal costs will be examined. In close collaboration with various stakeholders, a quasi-experimental study was developed, for which children of four intervention schools (n = 1200) in the southern part of the Netherlands are compared with children of four control schools (n = 1200) in the same region. The interventions started in November 2015. In two of the four intervention schools, a whole-school approach named 'The Healthy Primary School of the Future', is implemented with the aim of improving physical activity and dietary behaviour. For this intervention, pupils are offered an extended curriculum, including a healthy lunch, more physical exercises, and social and educational activities, next to the regular school curriculum. In the two other intervention schools, a physical-activity school approach called 'The Physical Activity School', is implemented, which is essentially similar to the other intervention, except that no lunch is provided. The interventions proceed during a period of 4 years. Apart from the effectiveness of both interventions, the process, the cost-effectiveness, and the expected legal implications are studied. Data collection is conducted within the school system. The baseline measurements started in September 2015 and yearly follow-up measurements are taking place until 2019. A whole-school approach is a new concept in the Netherlands. Due to its innovative, multifaceted nature and sound scientific foundation, these integrated programmes

The Healthy Primary School of the Future: study protocol of a quasi-experimental study

Directory of Open Access Journals (Sweden)

M. Willeboordse

2016-07-01

Full Text Available Abstract Background Unhealthy lifestyles in early childhood are a major global health challenge. These lifestyles often persist from generation to generation and contribute to a vicious cycle of health-related and social problems. This design article presents a study evaluating the effects of two novel healthy school interventions. The main outcome measure will be changes in children’s body mass index (BMI. In addition, lifestyle behaviours, academic achievement, child well-being, socio-economic differences, and societal costs will be examined. Methods In close collaboration with various stakeholders, a quasi-experimental study was developed, for which children of four intervention schools (n = 1200 in the southern part of the Netherlands are compared with children of four control schools (n = 1200 in the same region. The interventions started in November 2015. In two of the four intervention schools, a whole-school approach named ‘The Healthy Primary School of the Future’, is implemented with the aim of improving physical activity and dietary behaviour. For this intervention, pupils are offered an extended curriculum, including a healthy lunch, more physical exercises, and social and educational activities, next to the regular school curriculum. In the two other intervention schools, a physical-activity school approach called ‘The Physical Activity School’, is implemented, which is essentially similar to the other intervention, except that no lunch is provided. The interventions proceed during a period of 4 years. Apart from the effectiveness of both interventions, the process, the cost-effectiveness, and the expected legal implications are studied. Data collection is conducted within the school system. The baseline measurements started in September 2015 and yearly follow-up measurements are taking place until 2019. Discussion A whole-school approach is a new concept in the Netherlands. Due to its innovative, multifaceted

Solid waste management in primary healthcare centers: application of a facilitation tool.

Science.gov (United States)

Moreira, Ana Maria Maniero; Günther, Wanda Maria Risso

2016-08-18

to propose a tool to facilitate diagnosis, formulation and evaluation of the Waste Management Plan in Primary Healthcare Centers and to present the results of the application in four selected units. descriptive research, covering the stages of formulation /application of the proposed instrument and the evaluation of waste management performance at the units. the tool consists in five forms; specific indicators of waste generation for outpatients healthcare units were proposed, and performance indicators that give scores for compliance with current legislation. In the studied units it is generated common waste (52-60%), infectious-sharps (31-42%) and recyclable (5-17%). The average rates of generation are: 0,09kg of total waste/outpatient assistance and 0,09kg of infectious-sharps waste/outpatient procedure. The compliance with regulations, initially 26-30%, then reached 30-38% a year later. the tool showed to be easy to use, bypassing the existence of a complex range of existing regulatory requirements, allowed to identify non-conformities, pointed out corrective measures and evaluated the performance of waste management. In this sense, it contributes to decision making and management practices relating to waste, tasks usually assigned to nurses. It is recommended that the tool be applied in similar healthcare units for comparative studies, and implementation of necessary adaptations for other medical services. propor instrumento para facilitar diagnóstico, elaboração e avaliação de Plano de Gerenciamento de Resíduos em Unidades Básicas de Saúde e apresentar os resultados da aplicação em quatro unidades selecionadas. pesquisa descritiva que contemplou as etapas de construção/aplicação do instrumento proposto e a avaliação de desempenho do gerenciamento de resíduos nas unidades estudadas. geração de instrumento composto por cinco formulários; proposta de indicadores específicos de geração de resíduos para unidades assistenciais de saúde sem

Evaluating Amazon's Mechanical Turk as a tool for experimental behavioral research.

Directory of Open Access Journals (Sweden)

Matthew J C Crump

Full Text Available Amazon Mechanical Turk (AMT is an online crowdsourcing service where anonymous online workers complete web-based tasks for small sums of money. The service has attracted attention from experimental psychologists interested in gathering human subject data more efficiently. However, relative to traditional laboratory studies, many aspects of the testing environment are not under the experimenter's control. In this paper, we attempt to empirically evaluate the fidelity of the AMT system for use in cognitive behavioral experiments. These types of experiment differ from simple surveys in that they require multiple trials, sustained attention from participants, comprehension of complex instructions, and millisecond accuracy for response recording and stimulus presentation. We replicate a diverse body of tasks from experimental psychology including the Stroop, Switching, Flanker, Simon, Posner Cuing, attentional blink, subliminal priming, and category learning tasks using participants recruited using AMT. While most of replications were qualitatively successful and validated the approach of collecting data anonymously online using a web-browser, others revealed disparity between laboratory results and online results. A number of important lessons were encountered in the process of conducting these replications that should be of value to other researchers.

Primary Central Nervous System Lymphoma: Incorporating MRI in the Planning of Treatment Strategies

International Nuclear Information System (INIS)

Eloraby, A.; Zaki, I.

2001-01-01

Primary lymphoma of the central nervous system is becoming increasingly encountered secondary to the acquired immune-deficiency disorders. MRI is rapidly evolving diagnostic tool in the management of the lymphomatous CNS primary infiltrates. Methods and materials: 40 patients of the National Cancer Institute of Cairo University were studied by medium and high power MRI machines before and after intra-venous contrast enhancement. Results: The cerebral lesions exhibited specific diagnostic criteria regarding the anatomical configuration, signal pattern, peri-focal oedema and response to steroids, such manifestations made. Conclusion: MRI a highly reliable tool in the management of the disease. The work proved that spinal cord primary lymphoma is a rare entity

Acquisition and treatment systems for experimental data

International Nuclear Information System (INIS)

Bouard, E.

1988-01-01

The acquisition and treatment systems for experimental data has been conceived to give a response to experimental requirements in a research reactor such OSIRIS. Its objective is to acquire and treat the ensemble of informations coming from one or many experiences, to archive useful data for an ulterior treatment and to give at the experimentator a tool ensemble for a better track of his experience. Its main characteristics are given in this text [fr

Primary water chemistry optimization for extended fuel cycle operation. Results of the 'Duo experimentation' after three cycles

International Nuclear Information System (INIS)

Viricel, L.; Andrieu, C.; Segura, J.C.; Rocher, A.; Thomazet, J.; Clinard, M.H.; Dacquait, F.

2002-01-01

The primary coolant conditioning in French nuclear power plants is essentially based on the boron-lithium coordinated chemistry, with a target pH of 7.2 at 300 C and a maximum lithium concentration of 2.2 mg/kg. In 1996, EDF 1300 MWe units began operating 18-month fuel cycles, increasing boron concentrations at the beginning of the cycles. Since today the maximum lithium concentration in normal operation is 2.2 mg/kg, extended cycle operation results in a decrease in the pH at the beginning of the cycles, which may possibly lead to deposits in RCS, and particularly on the fuel cladding, and increased dose rates. It has to be noted that today, the fuel assemblies maximum burnup is set at 52 GWd/tU. One solution is to adjust the pH by increasing the lithium content at the beginning of the cycles, which is easy to implement and does not require any modification on the units. Hence, EDF is testing a ''modified'' chemistry regime in the > during 4 fuel cycles, with a maximum authorized lithium content of 3.5 mg/kg at the beginning of the cycles in the Cattenom 2 pilot unit. The Golfech 1 reference unit implements a standard boron-lithium coordination pH 300 7.2. The major goal of the experimentation is to assess the impact of elevated lithium concentrations at the beginning of the cycles on fuel cladding oxide behavior, mass transport and dose rates. This paper presents the results of the first three cycles of the Duo experimentation. (author)

Experimental evidence for the co-evolution of hominin tool-making teaching and language.

Science.gov (United States)

Morgan, T J H; Uomini, N T; Rendell, L E; Chouinard-Thuly, L; Street, S E; Lewis, H M; Cross, C P; Evans, C; Kearney, R; de la Torre, I; Whiten, A; Laland, K N

2015-01-13

Hominin reliance on Oldowan stone tools-which appear from 2.5 mya and are believed to have been socially transmitted-has been hypothesized to have led to the evolution of teaching and language. Here we present an experiment investigating the efficacy of transmission of Oldowan tool-making skills along chains of adult human participants (N=184) using five different transmission mechanisms. Across six measures, transmission improves with teaching, and particularly with language, but not with imitation or emulation. Our results support the hypothesis that hominin reliance on stone tool-making generated selection for teaching and language, and imply that (i) low-fidelity social transmission, such as imitation/emulation, may have contributed to the ~700,000 year stasis of the Oldowan technocomplex, and (ii) teaching or proto-language may have been pre-requisites for the appearance of Acheulean technology. This work supports a gradual evolution of language, with simple symbolic communication preceding behavioural modernity by hundreds of thousands of years.

Primary water chemistry optimization for extended fuel cycle operation. Results of the 'Duo experimentation' after three cycles

Energy Technology Data Exchange (ETDEWEB)

Viricel, L.; Andrieu, C.; Segura, J.C.; Rocher, A. [Electricite de France (France); Thomazet, J.; Clinard, M.H. [Framatome ANP (France); Dacquait, F. [Commissariat a l' Energie Atomique (France)

2002-07-01

The primary coolant conditioning in French nuclear power plants is essentially based on the boron-lithium coordinated chemistry, with a target pH of 7.2 at 300 C and a maximum lithium concentration of 2.2 mg/kg. In 1996, EDF 1300 MWe units began operating 18-month fuel cycles, increasing boron concentrations at the beginning of the cycles. Since today the maximum lithium concentration in normal operation is 2.2 mg/kg, extended cycle operation results in a decrease in the pH at the beginning of the cycles, which may possibly lead to deposits in RCS, and particularly on the fuel cladding, and increased dose rates. It has to be noted that today, the fuel assemblies maximum burnup is set at 52 GWd/tU. One solution is to adjust the pH by increasing the lithium content at the beginning of the cycles, which is easy to implement and does not require any modification on the units. Hence, EDF is testing a ''modified'' chemistry regime in the << Duo experimentation >> during 4 fuel cycles, with a maximum authorized lithium content of 3.5 mg/kg at the beginning of the cycles in the Cattenom 2 pilot unit. The Golfech 1 reference unit implements a standard boron-lithium coordination pH{sub 300} 7.2. The major goal of the experimentation is to assess the impact of elevated lithium concentrations at the beginning of the cycles on fuel cladding oxide behavior, mass transport and dose rates. This paper presents the results of the first three cycles of the Duo experimentation. (author)

Engaging Boys through Self-Reflection Using an Online Journaling Tool

Science.gov (United States)

Campbell, Chris; Deed, Craig

2009-01-01

The study reported here investigated whether Year 6 boys were engaged through the use of an online journaling tool. This journaling tool allowed the students to self reflect on their behaviour and affective reaction in an online environment. Case study methodology was used with twelve boys from a regional primary school in Victoria, during the one…

Experimental study on the effect of welding speed and tool pin ...

African Journals Online (AJOL)

user

Friction stir welding (FSW) is a novel solid state welding process for joining metallic alloys and ... compared with conventional welding methods such as TIG or MIG. ... Conventional fusion welding of aluminium alloys often produces a weld which .... Ti. 0.1%. Cr. 0.25%. Al. Balance. 3.1 Configuration of welding tool geometry.

The experimental definition of the acoustic standing wave series shapes, formed in the coolant of the primary circuit of VVER-440 type reactor

International Nuclear Information System (INIS)

Bulavin, V.V.; Pavelko, V.I.

1995-01-01

On the basis of pressure fluctuation measurements in some primary circuit loops at 2 nd Unit of Kola NPP with VVER-440 type reactors, the shapes of acoustic standing waves (ASW) were determined at frequencies corresponding to four minimal oscillation eigenfrequencies in the primary circuit coolant. On identification of the ASW modes and properties, experimental results based on six circulating loops in symmetric arrangement allowed determination of the three-dimensional space structure of the wave nodes and antinodes inside and outside of the reactor vessel (RV). As part of this analysis, the geometric features of the primary circuit that caused the formation of these standing waves were identified. Differences in each ASW shape were shown to cause different individual effects on the neutron field in the reactor core and on fuel assembly vibration. This has been partially confirmed by ex-core neutron ionization chamber noise analysis. One type of ASW, possessing an antinode inside the RV, can be used for measurement of the pressure coefficient of reactivity. However, this must be done with care to avoid the potential for incorrect results in some cases. The results presented in this paper can be readily extended to other VVER type reactors with both odd and even number of loops. (author)

An experimental investigation of the interaction of primary and secondary stresses in fuel plates

International Nuclear Information System (INIS)

Swinson, W.F.; Battiste, R.L.; Yahr, G.T.

1996-01-01

If the load is not relieved as a structure starts to yield, the induced stress is defined as primary stress. If the load relaxes, as a structure begins yield the induced stress is defined as secondary stress. In design it is not uncommon to give more weight to primary stresses than to secondary stresses. However, knowing when this is good design practice and when it is not good design practice represents a problem. In particular, the fuel plates in operating reactors contain both primary stresses and secondary stresses and to properly assess a design there is a need to assign design weights to the stresses. Tests were conducted on reactor fuel plates intended for the Advanced Neutron Source (ANS) to determine the potential of giving different design weights to the primary and secondary stresses. The results of these tests and the conclusion that the stresses should be weighted the same are given in this paper

An experimental investigation on the interaction of primary and secondary stresses in fuel plates

International Nuclear Information System (INIS)

Swinson, W.F.; Battiste, R.L.; Yahr, G.T.

1997-01-01

If the load is not relieved as a structure starts to yield, the induced stress is defined as primary stress. If the load relaxes, as a structure begins to yield the induced stress is defined as secondary stress. In design, it is not uncommon to give more weight to primary stresses than to secondary stresses. However, knowing when this is good design practice and when it is not good design practice represent a problem. In particular, the fuel plates in operating reactors contain both primary stresses and secondary stresses, and to properly assess a design there is a need to assign design weights to the stresses. Tests were conducted on reactor fuel plates intended for the advanced neutron source (ANS) to determine the potential of giving different design weights to the primary and secondary stresses. The results of these tests and the conclusion that the stresses should be weighted the same are given in this paper

Tools and data for the geochemical modeling. Thermodynamic data for sulfur species and background salts and tools for the uncertainty analysis; WEDA. Werkzeuge und Daten fuer die Geochemische Modellierung. Thermodynamische Daten fuer Schwefelspezies und Hintergrundsalze sowie Tools zur Unsicherheitsanalyse

Energy Technology Data Exchange (ETDEWEB)

Hagemann, Sven; Schoenwiese, Dagmar; Scharge, Tina

2015-07-15

The report on tools and data for the geochemical modeling covers the following issues: experimental methods and theoretical models, design of a thermodynamic model for reduced sulfur species, thermodynamic models for background salts, tools for the uncertainty and sensitivity analyses of geochemical equilibrium modeling.

Development of an educational tool to teach primary school pupils multiplication tables

CSIR Research Space (South Africa)

Smith, S

2015-11-01

Full Text Available This work addresses the need for the development of skills and interest in mathematics, particularly for students in the early years of primary school where core mathematical knowledge is formed. The development and implementation of Maths Mat...

Possibilities of Application of High Pressure Jet Assisted Machining in Hard Turning with Carbide Tools

Directory of Open Access Journals (Sweden)

G. Globočki Lakić

2017-06-01

Full Text Available High Pressure Jet Assisted Machining (HPJAM in turning is a hybrid machining method in which a high pressure jet of cooling and lubrication fluid, under high pressure (50 MPa, leads to the zone between the cutting tool edge and workpiece. An experimental study was performed to investigate the capabilities of conventional and high pressure cooling (HPC in the turning of hard-to-machine materials: hard-chromed and surface hardened steel Ck45 (58 HRc and hardened bearing steel 100Cr6 (62 HRc. Machining experiments were performed using coated carbide tools and highly cutting speed. Experimental measurements were performed for different input process parameters. The cooling capabilities are compared by monitoring of tool wear, tool life, cooling efficiency, and surface roughness. Connection between the tool wear and surface roughness is established. Experimental research show that the hard turning with carbide cutting tools and HP supply CLF provides numerous advantages from the techno-economic aspect: greater productivity, reduce of temperature in the cutting zone, improved control chip formation, extended tool life, low intensity of tool wear, surface roughness in acceptable limits, significant reduce of production costs related to the CLF.

Analysis of the AMMON experimental program in the EOLE facility supporting the qualification of the JHR neutron and photon tools

International Nuclear Information System (INIS)

Vaglio-Gaudard, C.; Colombier, A.C.; Hudelot, J.P.; Leray, O.; Lemaire, M.; Di-Salvo, J.; Gruel, A.; Sireta, P.

2013-06-01

The first divergence of the international Jules Horowitz Material Testing Reactor under construction at CEA Cadarache is foreseen in 2016. In order to perform all the design and safety studies, a specific neutron and photon calculation tool, HORUS3D/N and P, dedicated to the JHR simulation, was developed. This development follows the V and V-UQ process; in this frame, the validation and qualification steps aim at quantifying all the biases and associated uncertainties of HORUS3D/N and P calculations. These biases originate from both the nuclear data and the calculation scheme, for calculations at step zero (JHR BOL core) or during depletion (JHR core at equilibrium). This paper focusses on the quantification of the biases due to nuclear data and the associated uncertainties. A new experimental program, named AMMON, was performed between 2010 and 2013 to provide experimental data for this quantification. A large part of the measurements has been today analyzed with the Monte Carlo TRIPOLI-4 R code and the JEFF3.1.1 and EPDL97 data libraries relative to neutron/photon transport and photon emission. The C/E results were transposed from AMMON to JHR. The synthesis of the present analysis is very satisfactory. The calculation biases remains limited. In addition, thanks to a very good control to the experimental uncertainties during measurements, it is shown that the a priori uncertainties due to nuclear data for parameters at step zero was reduced up to a factor of 2. (authors)

Obstacles to the Primary and Secondary Prevention of Breast Cancer in African-American Women

National Research Council Canada - National Science Library

Hargreaves, Margaret

1997-01-01

Study objectives are to develop a quantitative assessment tool to describe barriers to primary and secondary prevention of breast cancer, to use this tool to establish preliminary norms in an urban...

Müller cells and retinal axons can be primary targets in experimental neuromyelitis optica spectrum disorder.

Science.gov (United States)

Zeka, Bleranda; Lassmann, Hans; Bradl, Monika

2017-01-01

Recent work from our laboratory, using different models of experimental neuromyelitis optica spectrum disorder (NMOSD), has led to a number of observations that might be highly relevant for NMOSD patients. For example: (i) in the presence of neuromyelitis optica immunoglobulin G, astrocyte-destructive lesions can be initiated by CD4+ T cells when these cells recognize aquaporin 4 (AQP4), but also when they recognize other antigens of the central nervous system. The only important prerequisite is that the T cells have to be activated within the central nervous system by "their" specific antigen. Recently activated CD4+ T cells with yet unknown antigen specificity are also found in human NMOSD lesions. (ii) The normal immune repertoire might contain AQP4-specific T cells, which are highly encephalitogenic on activation. (iii) The retina might be a primary target of AQP4-specific T cells and neuromyelitis optica immunoglobulin G: AQP4-specific T cells alone are sufficient to cause retinitis with low-grade axonal pathology in the retinal nerve fiber/ganglionic cell layer. A thinning of these layers is also observed in NMOSD patients, where it is thought to be a consequence of optic neuritis. Neuromyelitis optica immunoglobulin G might target cellular processes of Müller cells and cause their loss of AQP4 reactivity, when AQP4-specific T cells open the blood-retina barrier in the outer plexiform layer. Patchy loss of AQP4 reactivity on Müller cells of NMOSD patients has been recently described. Cumulatively, our findings in experimental NMOSD suggest that both CD4+ T cell and antibody responses directed against AQP4 might play an important role in the pathogenesis of tissue destruction seen in NMOSD.

Machinability of an experimental Ti-Ag alloy in terms of tool life in a dental CAD/CAM system.

Science.gov (United States)

Inagaki, Ryoichi; Kikuchi, Masafumi; Takahashi, Masatoshi; Takada, Yukyo; Sasaki, Keiichi

2015-01-01

Titanium is difficult to machine because of its intrinsic properties. In a previous study, the machinability of titanium was improved by alloying with silver. This study aimed to evaluate the durability of tungsten carbide burs after the fabrication of frameworks using a Ti-20%Ag alloy and titanium with a computer-aided design and computer-aided manufacturing system. There was a significant difference in attrition area ratio between the two metals. Compared with titanium, the ratio of the area of attrition of machining burs was significantly lower for the experimental Ti-20%Ag alloy. The difference in the area of attrition for titanium and Ti-20%Ag became remarkable with increasing number of machining operations. The results show that the same burs can be used for a longer time with Ti-20%Ag than with pure titanium. Therefore, in terms of tool life, the machinability of the Ti-20%Ag alloy is superior to that of titanium.

Contribution of computerized tomography to diagnosis of primary hyperaldosteronism

International Nuclear Information System (INIS)

Hrabaneova, J.; Stribrna, J.; Bultasova, H.; Karasova, L.; Placer, Z.; Pinsker, P.

1987-01-01

Two cases are reported of computerized tomography (CT) examination for proof of suspect primary hyperaldosteronism caused by adenoma of the adrenals. The findings were then confirmed surgically and histologically. CT was again found to be an invaluable tool for differential diagnosis of this condition, which spared the patients demanding invasive examinations and clearly differentiated primary hyperaldosteronism from adrenal cortex hyperplasia. This is mainly important for the fact that adenoma or more rarely carcinoma causing primary hyperaldosteronism can surgically be removed. (L.O.). 2 figs., 2 tabs., 6 refs

Reliable tool life measurements in turning - an application to cutting fluid efficiency evaluation

DEFF Research Database (Denmark)

Axinte, Dragos A.; Belluco, Walter; De Chiffre, Leonardo

2001-01-01

The paper proposes a method to obtain reliable measurements of tool life in turning, discussing some aspects related to experimental procedure and measurement accuracy. The method (i) allows and experimental determination of the extended Taylor's equation, with a limited set of experiments and (ii......) provides efficiency evaluation. Six cutting oils, five of which formulated from vegetable basestock, were evaluated in turning. Experiments were run in a range of cutting parameters. according to a 2, 3-1 factorial design, machining AISI 316L stainless steel with coated carbide tools. Tool life...

Analysis of the influence of tool dynamics in diamond turning

Energy Technology Data Exchange (ETDEWEB)

Fawcett, S.C.; Luttrell, D.E.; Keltie, R.F.

1988-12-01

This report describes the progress in defining the role of machine and interface dynamics on the surface finish in diamond turning. It contains a review of literature from conventional and diamond machining processes relating tool dynamics, material interactions and tool wear to surface finish. Data from experimental measurements of tool/work piece interface dynamics are presented as well as machine dynamics for the DTM at the Center.

Relational aggression: the voices of primary school learners

African Journals Online (AJOL)

This was done within a qualitative research design with a ... the research design and methods that were used to explore primary school learners' experience of RA at ...... “Qualitative research” Analysis types and software tools. New York: ...

Status of experimental data for the VHTR core design

Energy Technology Data Exchange (ETDEWEB)

Park, Won Seok; Chang, Jong Hwa; Park, Chang Kue

2004-05-01

The VHTR (Very High Temperature Reactor) is being emerged as a next generation nuclear reactor to demonstrate emission-free nuclear-assisted electricity and hydrogen production. The VHTR could be either a prismatic or pebble type helium cooled, graphite moderated reactor. The final decision will be made after the completion of the pre-conceptual design for each type. For the pre-conceptual design for both types, computational tools are being developed. Experimental data are required to validate the tools to be developed. Many experiments on the HTGR (High Temperature Gas-cooled Reactor) cores have been performed to confirm the design data and to validate the design tools. The applicability and availability of the existing experimental data have been investigated for the VHTR core design in this report.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

OpenAIRE

Garc?a Nieto, Paulino Jos?; Garc?a-Gonzalo, Esperanza; Ord??ez Gal?n, Celestino; Bernardo S?nchez, Antonio

2016-01-01

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism i...

Cinema Sessions in Primary Care

Directory of Open Access Journals (Sweden)

Francisco Ignacio MORETA-VELAYOS

2016-04-01

Full Text Available For a long time films have been used in teaching and at various levels of professional training  and more specifically in the medical area. In this case, through the description of a project developed in a Primary Care Health Center, we intend to justify the use of movies as a tool that could ease, the sometimes difficult task of continued education among Primary Care professionals. We propose different aspects of everyday practice in which cinema can be potentially useful, as well as the way to include it in the Plan of Continued Education of the Centre and its accreditation.Films and issues discussed in each session, and the project evaluation, are detailed.

Whole-body multislice computed tomography as the primary and sole diagnostic tool in patients with blunt trauma: searching for its appropriate indication.

Science.gov (United States)

Wurmb, Thomas Erik; Frühwald, Peter; Hopfner, Wittiko; Roewer, Norbert; Brederlau, Jörg

2007-11-01

In our hospital, whole-body multislice computed tomography is used as the primary diagnostic tool in patients with suspected multiple trauma. A triage rule is used for its indication. We have retrospectively analyzed data of sedated, intubated and ventilated patients consecutively admitted to our trauma center to assess whether the triage rule can help identify patients with severe trauma (injury severity score > or = 16). We have found that overtriage (injury severity score < 16) occurs in 30%, and undertriage occurs in 6% of patients. Although we have found the triage rule to be highly sensitive, this results in a high rate of overtriage. Until we know more about the most relevant and independent predictive factors, sole reliance upon multislice computed tomography in triaging suspected polytrauma victims will imply the risk to overscan many patients.

[Use of COPD-6 Vitalograph in Primary Care as tool for smoking cessation].

Science.gov (United States)

Antón-García, F; Pruteanu, D F; Correcher-Salvador, E

2016-03-01

To assess the evolution of smoking cessation process after using a COPD-6 Vitalograph in smokers that came to a primary care practice (PCP) during a three year period (March 2011- February 2013). To assess if there are any new COPD diagnoses and to compare the smoking cessation outcomes to those of a specific smoking cessation practice (SSCP) from another healthcare centre. Two devices were used: Vitalograph (electronic device measuring the lung function) and the CO-oximeter, in 176 patients (active search of smokers). tobacco pack-years, tobacco dependence (shortened Fagerström test), CO in exhaled breath (in parts per million-ppm), personal history of COPD or cardiovascular disease (CVD). The patients performed three forced exhalations and the Vitalograph registered the lung function (FEV1, FEV6, FEV1/FEV6) and the estimated lung age (ELA). Patient attitude was assessed (phases: pre-contemplation, contemplation, preparation) before and after the test, informing them of the outcomes. Patient progress in the smoking cessation process was also recorded. A total of 176 smokers were studied in PCP and 33 in SSCP. PCP/SSCP: age: 45.9/51.6 years old (p=042); pack-years 25.5/39.3 (p=0001); patients who quit smoking and used medicines for it 2/9. In PCP: age-ELA 45.9/57.4 (p=0.000). In SSCP: age-ELA 51.6/74.3 (p=000). Smoking habit evolution PCP/SSCP: cessation 24.5%/48.5% (p=004). Difference 24%. CI difference (6.4-42.8%). In PCP new COPD diagnosis in 6 smokers. COPD-6 Vitalograph is a fast and easy to use tool in day-to-day practice. The percentage of smoking cessation is better in SSCP, although a high smoking cessation rate was obtained in PCP (active search). Copyright © 2014 Sociedad Española de Médicos de Atención Primaria (SEMERGEN). Publicado por Elsevier España, S.L.U. All rights reserved.

New Caledonian crows attend to multiple functional properties of complex tools.

Science.gov (United States)

St Clair, James J H; Rutz, Christian

2013-11-19

The ability to attend to the functional properties of foraging tools should affect energy-intake rates, fitness components and ultimately the evolutionary dynamics of tool-related behaviour. New Caledonian crows Corvus moneduloides use three distinct tool types for extractive foraging: non-hooked stick tools, hooked stick tools and tools cut from the barbed edges of Pandanus spp. leaves. The latter two types exhibit clear functional polarity, because of (respectively) a single terminal, crow-manufactured hook and natural barbs running along one edge of the leaf strip; in each case, the 'hooks' can only aid prey capture if the tool is oriented correctly by the crow during deployment. A previous experimental study of New Caledonian crows found that subjects paid little attention to the barbs of supplied (wide) pandanus tools, resulting in non-functional tool orientation during foraging. This result is puzzling, given the presumed fitness benefits of consistently orienting tools functionally in the wild. We investigated whether the lack of discrimination with respect to (wide) pandanus tool orientation also applies to hooked stick tools. We experimentally provided subjects with naturalistic replica tools in a range of orientations and found that all subjects used these tools correctly, regardless of how they had been presented. In a companion experiment, we explored the extent to which normally co-occurring tool features (terminal hook, curvature of the tool shaft and stripped bark at the hooked end) inform tool-orientation decisions, by forcing birds to deploy 'unnatural' tools, which exhibited these traits at opposite ends. Our subjects attended to at least two of the three tool features, although, as expected, the location of the hook was of paramount importance. We discuss these results in the context of earlier research and propose avenues for future work.

Influence of minimum quantity of lubricant (MQL on tool life of carbide cutting tools during milling process of steel AISI 1018

Directory of Open Access Journals (Sweden)

Diego Núñez

2017-03-01

Full Text Available Nowadays, high productivity of machining is an important issue to obtain economic benefits in the industry. This purpose could be reached with high cutting velocity and feed rate. However, the inherently behavior produce high temperatures in the interface of couple cutting tool/workpiece. Many cutting fluids have been developed to control temperature in process and increase tool life. The objective of this paper is to compare the carbide milling tool wear using different systems cutting fluids: flood and minimum quantity of lubrication (MQL. The values of carbide milling cutting tool wear was evaluate according with the standard ISO 8688-1 1989. The experimental results showed that using MQL reduces significantly (about 40% tool wear in milling AISI 1018 steel at industrial cutting conditions.

Primary Schooling in West Bengal

Science.gov (United States)

Sen, Amartya

2010-01-01

With his Nobel Prize award money, Amartya Sen set up the Pratichi Trust which carries out research, advocacy and experimental projects in basic education, primary health care, and women's development in West Bengal and Bangladesh. Professor Sen himself took active interest in this work--helping set the agenda, looking at the evidence from…

Cell Culture Microfluidic Biochips: Experimental Throughput Maximization

DEFF Research Database (Denmark)

Minhass, Wajid Hassan; Pop, Paul; Madsen, Jan

2011-01-01

Microfluidic biochips offer a promising alternative to a conventional biochemical laboratory, integrating all necessary functionalities on-chip in order to perform biochemical applications. Researchers have started to propose computer-aided design tools for the synthesis of such biochips. Our focus...... metaheuristic for experimental design generation for the cell culture microfluidic biochips, and we have evaluated our approach using multiple experimental setups....

Data Mining Tools for Malware Detection

CERN Document Server

Masud, Mehedy; Thuraisingham, Bhavani; Andreasson, Kim J

2011-01-01

Although the use of data mining for security and malware detection is quickly on the rise, most books on the subject provide high-level theoretical discussions to the near exclusion of the practical aspects. Breaking the mold, Data Mining Tools for Malware Detection provides a step-by-step breakdown of how to develop data mining tools for malware detection. Integrating theory with practical techniques and experimental results, it focuses on malware detection applications for email worms, malicious code, remote exploits, and botnets. The authors describe the systems they have designed and devel

Key elements of high-quality practice organisation in primary health care: a systematic review.

Science.gov (United States)

Crossland, Lisa; Janamian, Tina; Jackson, Claire L

2014-08-04

To identify elements that are integral to high-quality practice and determine considerations relating to high-quality practice organisation in primary care. A narrative systematic review of published and grey literature. Electronic databases (PubMed, CINAHL, the Cochrane Library, Embase, Emerald Insight, PsycInfo, the Primary Health Care Research and Information Service website, Google Scholar) were searched in November 2013 and used to identify articles published in English from 2002 to 2013. Reference lists of included articles were searched for relevant unpublished articles and reports. Data were configured at the study level to allow for the inclusion of findings from a broad range of study types. Ten elements were most often included in the existing organisational assessment tools. A further three elements were identified from an inductive thematic analysis of descriptive articles, and were noted as important considerations in effective quality improvement in primary care settings. Although there are some validated tools available to primary care that identify and build quality, most are single-strategy approaches developed outside health care settings. There are currently no validated organisational improvement tools, designed specifically for primary health care, which combine all elements of practice improvement and whose use does not require extensive external facilitation.

MATLAB platform for Monte Carlo planning and dosimetry experimental evaluation

International Nuclear Information System (INIS)

Baeza, J. A.; Ureba, A.; Jimenez-Ortega, E.; Pereira-Barbeiro, A. R.; Leal, A.

2013-01-01

A new platform for the full Monte Carlo planning and an independent experimental evaluation that it can be integrated into clinical practice. The tool has proved its usefulness and efficiency and now forms part of the flow of work of our research group, the tool used for the generation of results, which are to be suitably revised and are being published. This software is an effort of integration of numerous algorithms of image processing, along with planning optimization algorithms, allowing the process of MCTP planning from a single interface. In addition, becomes a flexible and accurate tool for the evaluation of experimental dosimetric data for the quality control of actual treatments. (Author)

Experimental benchmark and code validation for airfoils equipped with passive vortex generators

International Nuclear Information System (INIS)

Baldacchino, D; Ferreira, C; Florentie, L; Timmer, N; Van Zuijlen, A; Manolesos, M; Chaviaropoulos, T; Diakakis, K; Papadakis, G; Voutsinas, S; González Salcedo, Á; Aparicio, M; García, N R.; Sørensen, N N.; Troldborg, N

2016-01-01

Experimental results and complimentary computations for airfoils with vortex generators are compared in this paper, as part of an effort within the AVATAR project to develop tools for wind turbine blade control devices. Measurements from two airfoils equipped with passive vortex generators, a 30% thick DU97W300 and an 18% thick NTUA T18 have been used for benchmarking several simulation tools. These tools span low-to-high complexity, ranging from engineering-level integral boundary layer tools to fully-resolved computational fluid dynamics codes. Results indicate that with appropriate calibration, engineering-type tools can capture the effects of vortex generators and outperform more complex tools. Fully resolved CFD comes at a much higher computational cost and does not necessarily capture the increased lift due to the VGs. However, in lieu of the limited experimental data available for calibration, high fidelity tools are still required for assessing the effect of vortex generators on airfoil performance. (paper)

PRIMARY STUDENTS' STEREOTYPIC IMAGE OF INVENTOR IN KOREA

Directory of Open Access Journals (Sweden)

Eunsang Lee

2018-04-01

Full Text Available The purpose of this research is to compare the previous stereotypes of the scientist image and the current stereotypes of the inventor image among Korean students. For this purpose, three primary schools located in the metropolitan area of Korea were selected under a convenience sampling method, with one class selected for each of the 2nd, 4th, and 6th grades of each school. The conclusions of this research are as follows. First, analyzing students' stereotypes of the inventor image showed that older students had more stereotypes about inventors than younger students did. Second, as a result of analyzing the images according to each indicator, Korean students were found to have stereotypes about the inventor. Third, the symbol of research was expressed together with one of the science-related experiment tool and the making-related experiment tool. Fourth, primary students perceived the inventor as mainly male. Male students mostly drew male inventors and female students mostly drew female inventors. Based on the conclusions obtained through this research, various educational implications to be reflected in primary technology education were suggested to escape the stereotypes of the inventor’s image.

Investigating Climate Change and Reproduction: Experimental Tools from Evolutionary Biology

Directory of Open Access Journals (Sweden)

Oliver Y. Martin

2012-09-01

Full Text Available It is now generally acknowledged that climate change has wide-ranging biological consequences, potentially leading to impacts on biodiversity. Environmental factors can have diverse and often strong effects on reproduction, with obvious ramifications for population fitness. Nevertheless, reproductive traits are often neglected in conservation considerations. Focusing on animals, recent progress in sexual selection and sexual conflict research suggests that reproductive costs may pose an underestimated hurdle during rapid climate change, potentially lowering adaptive potential and increasing extinction risk of certain populations. Nevertheless, regime shifts may have both negative and positive effects on reproduction, so it is important to acquire detailed experimental data. We hence present an overview of the literature reporting short-term reproductive consequences of exposure to different environmental factors. From the enormous diversity of findings, we conclude that climate change research could benefit greatly from more coordinated efforts incorporating evolutionary approaches in order to obtain cross-comparable data on how individual and population reproductive fitness respond in the long term. Therefore, we propose ideas and methods concerning future efforts dealing with reproductive consequences of climate change, in particular by highlighting the advantages of multi-generational experimental evolution experiments.

A predictive screening tool to detect diabetic retinopathy or macular edema in primary health care: construction, validation and implementation on a mobile application

Directory of Open Access Journals (Sweden)

Cesar Azrak

2015-11-01

Full Text Available The most described techniques used to detect diabetic retinopathy and diabetic macular edema have to be interpreted correctly, such that a person not specialized in ophthalmology, as is usually the case of a primary care physician, may experience difficulties with their interpretation; therefore we constructed, validated and implemented as a mobile app a new tool to detect diabetic retinopathy or diabetic macular edema (DRDME using simple objective variables. We undertook a cross-sectional, observational study of a sample of 142 eyes from Spanish diabetic patients suspected of having DRDME in 2012–2013. Our outcome was DRDME and the secondary variables were: type of diabetes, gender, age, glycated hemoglobin (HbA1c, foveal thickness and visual acuity (best corrected. The sample was divided into two parts: 80% to construct the tool and 20% to validate it. A binary logistic regression model was used to predict DRDME. The resulting model was transformed into a scoring system. The area under the ROC curve (AUC was calculated and risk groups established. The tool was validated by calculating the AUC and comparing expected events with observed events. The construction sample (n = 106 had 35 DRDME (95% CI [24.1–42.0], and the validation sample (n = 36 had 12 DRDME (95% CI [17.9–48.7]. Factors associated with DRDME were: HbA1c (per 1% (OR = 1.36, 95% CI [0.93–1.98], p = 0.113, foveal thickness (per 1 µm (OR = 1.03, 95% CI [1.01–1.04], p < 0.001 and visual acuity (per unit (OR = 0.14, 95% CI [0.00–0.16], p < 0.001. AUC for the validation: 0.90 (95% CI [0.75–1.00], p < 0.001. No significant differences were found between the expected and the observed outcomes (p = 0.422. In conclusion, we constructed and validated a simple rapid tool to determine whether a diabetic patient suspected of having DRDME really has it. This tool has been implemented on a mobile app. Further validation studies are required in the general diabetic population.

Design of the ITER Tokamak Assembly Tools

International Nuclear Information System (INIS)

Park, Hyunki; Her, Namil; Kim, Byungchul; Im, Kihak; Jung, Kijung; Lee, Jaehyuk; Im, Kisuk

2006-01-01

ITER (International Thermonuclear Experimental Reactor) Procurement allocation among the seven Parties, EU, JA, CN, IN , KO, RF and US had been decided in Dec. 2005. ITER Tokamak assembly tools is one of the nine components allocated to Korea for the construction of the ITER. Assembly tools except measurement and common tools are supplied to assemble the ITER Tokamak and classified into 9 groups according to components to be assembled. Among the 9 groups of assembly tools, large-sized Sector Sub-assembly Tools and Sector Assembly Tools are used at the first stage of ITER Tokamak construction and need to be designed faster than seven other assembly tools. ITER IT (International Team) proposed Korea to accomplish ITA (ITER Transitional Arrangements) Task on detailed design, manufacturing feasibility and contract specification of specific, large sized tools such as Upending Tool, Lifting Tool, Sector Sub-assembly Tool and Sector Assembly Tool in Oct. 2004. Based on the concept design by ITER IT, Korea carried out ITA Task on detailed design of large-sized and specific Sector Sub-assembly and Sector Assembly Tools until Mar. 2006. The Sector Sub-assembly Tools mainly consist of the Upending, Lifting, Vacuum Vessel Support and Bracing, and Sector Sub-assembly Tool, among which the design of three tools are herein. The Sector Assembly Tools mainly consist of the Toroidal Field (TF) Gravity Support Assembly, Sector In-pit Assembly, TF Coil Assembly, Vacuum Vessel (VV) Welding and Vacuum Vessel Thermal Shield (TS) Assembly Tool, among which the design of Sector In-pit Assembly Tool is described herein

LEGO Robotics: An Authentic Problem Solving Tool?

Science.gov (United States)

Castledine, Alanah-Rei; Chalmers, Chris

2011-01-01

With the current curriculum focus on correlating classroom problem solving lessons to real-world contexts, are LEGO robotics an effective problem solving tool? This present study was designed to investigate this question and to ascertain what problem solving strategies primary students engaged with when working with LEGO robotics and whether the…

Meta-Analysis for Primary and Secondary Data Analysis: The Super-Experiment Metaphor.

Science.gov (United States)

Jackson, Sally

1991-01-01

Considers the relation between meta-analysis statistics and analysis of variance statistics. Discusses advantages and disadvantages as a primary data analysis tool. Argues that the two approaches are partial paraphrases of one another. Advocates an integrative approach that introduces the best of meta-analytic thinking into primary analysis…

CFD analysis and experimental investigation associated with the design of the Los Alamos nuclear materials storage facility

International Nuclear Information System (INIS)

Bernardin, J.D.; Hopkins, S.; Gregory, W.S.; Martin, R.A.

1997-01-01

The Nuclear Materials Storage Facility (NMSF) at the Los Alamos National Laboratory is being renovated for long-term storage of canisters designed to hold heat-generating nuclear materials, such as powders, ingots, and other components. The continual heat generation within the canisters necessitates a reliable cooling scheme of sufficient magnitude which maintains the stored material temperatures within acceptable limits. The primary goal of this study was to develop both an experimental facility and a computational fluid dynamics (CFD) model of a subsection of the NMSF which could be used to observe general performance trends of a proposed passive cooling scheme and serve as a design tool for canister holding fixtures. Comparisons of numerical temperature and velocity predictions with empirical data indicate that the CFD model provides an accurate representation of the NMSF experimental facility. Minor modifications in the model geometry and boundary conditions are needed to enhance its accuracy, however, the various fluid and thermal models correctly capture the basic physics

COMPUTER TOOLS OF DYNAMIC MATHEMATIC SOFTWARE AND METHODICAL PROBLEMS OF THEIR USE

OpenAIRE

Olena V. Semenikhina; Maryna H. Drushliak

2014-01-01

The article presents results of analyses of standard computer tools of dynamic mathematic software which are used in solving tasks, and tools on which the teacher can support in the teaching of mathematics. Possibility of the organization of experimental investigating of mathematical objects on the basis of these tools and the wording of new tasks on the basis of the limited number of tools, fast automated check are specified. Some methodological comments on application of computer tools and ...

Education tools for entrepreneurship creating an action-learning environment through educational learning tools

CERN Document Server

Gómez, Jaime; Vélez-Torres, Francisco; Rueda-Armengot, Carlos

2016-01-01

This book examines education in entrepreneurship through an action-learning environment that employs various education tools, technology tools and pedagogical methods being implemented into university curriculums around the world. Entrepreneurship in all of its aspects, connotations, and applications has undoubtedly become a major force for new and sustainable wealth creation in both emerging and developed economies. This notion has been encouraging universities to incorporate entrepreneurship-related competencies into the curriculums of almost all subjects, as researchers, educators, and administrators alike acknowledge that students must be fully engaged and prepared to thrive in a society increasingly defined by innovation. In this context, the primary challenge consists in how to inspire or work beyond the mental limits in the classroom; to determine which learning platforms are required or useful to unlock and stimulate creativity and eliminate the human aversion to failure. Featuring contributions and c...

[Improving the teaching quality by multiple tools and technology in oral histopathology experimental course].

Science.gov (United States)

Tian, Zhen; Wang, Li-Zhen; Hu, Yu-Hua; Zhang, Chun-Ye; Li, Jiang

2017-04-01

Oral histopathology is a course which needs to be combined with theory and practice closely. Experimental course plays an important role in teaching oral histopathology. Here, we aim to explore a series of effective measures to improve the teaching quality of experimental course and tried to train observation, thinking, analysis and problem solving skills of dental students. We re-edited and updated the experimental textbook "guidelines of experimental course of oral histopathology", and published the reference book for experimental course--"color pocket atlas of oral histopathology: experiment and diadactic teaching". The number of clinicopathological cases for presentation and class discussion was increased, and high-quality teaching slides were added and replaced the poor-quality or worn out slides. We established a variety of teaching methods based on the internet, which provided an environment of self-directed learning for dental students. Instead of simple slice-reading examination, a new evaluation system based on computer was established. The questionnaire survey showed that the students spoke positively on the teaching reform for experimental course. They thought that the reform played a significant role in enriching the teaching content, motivating learning interest and promoting self-study. Compared with traditional examination, computer-based examination showed a great advantage on mastering professional knowledge systematically and comprehensively. The measures adopted in our teaching reform not only effectively improve the teaching quality of experimental course of oral histopathology, but also help the students to have a clear, logical thinking when facing complicated diseases and have the ability to apply theoretical knowledge into clinical practice.

[Animal experimentation, computer simulation and surgical research].

Science.gov (United States)

Carpentier, Alain

2009-11-01

We live in a digital world In medicine, computers are providing new tools for data collection, imaging, and treatment. During research and development of complex technologies and devices such as artificial hearts, computer simulation can provide more reliable information than experimentation on large animals. In these specific settings, animal experimentation should serve more to validate computer models of complex devices than to demonstrate their reliability.

effect of turning parameters on metal removal and tool wear rates

African Journals Online (AJOL)

user

2 SCHOOL OF AEROSPACE, TRANSPORT AND MANUFACTURING, CRANFIELD UNIV., ... AISI 1018 low carbon steel during turning operation to reduce tooling costs as a result of tool wear and achieve optimum metal ... performance of a system, part or component while ... traditional and experimental design methods of.

Storming a Citadel: Mathematical Theory and Experimental Practice

Science.gov (United States)

Sichau, Christian

2006-09-01

Based upon a comparison of the viscosity experiments of James Clerk Maxwell (1831 1879) and Oskar Emil Meyer (1834 1909) in the 1860s, I argue that mathematical theory plays a significant role in both aspects of experimental practice, the design and construction of an experimental apparatus and the transformation of the observed experimental data into the value of a physical quantity. I argue further that Maxwell’s and Meyer’s evaluation of each other’s theoretical and experimental work depended significantly on the mathematical tools they employed in their theories.

Radiochemical surveillance of KNK primary sodium

International Nuclear Information System (INIS)

Stamm, H.H.

1987-01-01

After 400 effective full power days (EFPD) and a maximum fuel burnup of 100000 MWd/t the reactor was shutdown in August 1982. After replacing the total KNK II/1 core by the second fast core KNK II/2, the plant went into operation again in August 1983. In August 1986 nearly 400 EFPD were achieved with the second core KNK II/2. It is foreseen to exent the operation up to 720 EFPD with the core KNK II/2. KNK II is widely used as is governed by the experimental program rather than by energy production. Radionuclides and other impurities in the primary sodium were determined for plant surveillance as well as for an extensive radiochemistry program. This experimental radiochemistry program includes investigations of radionuclide deposition on pretreated surfaces under flowing sodium and development of new methods for trapping of radionuclides from primary sodium. Aim of this work is to minimize the radiation exposure associated with maintenance and repair work. (orig./HP)

Artificial intelligence for the EChO mission planning tool

Science.gov (United States)

Garcia-Piquer, Alvaro; Ribas, Ignasi; Colomé, Josep

2015-12-01

The Exoplanet Characterisation Observatory (EChO) has as its main goal the measurement of atmospheres of transiting planets. This requires the observation of two types of events: primary and secondary eclipses. In order to yield measurements of sufficient Signal-to-Noise Ratio to fulfil the mission objectives, the events of each exoplanet have to be observed several times. In addition, several criteria have to be considered to carry out each observation, such as the exoplanet visibility, its event duration, and no overlapping with other tasks. It is expected that a suitable mission plan increases the efficiency of telescope operation, which will represent an important benefit in terms of scientific return and operational costs. Nevertheless, to obtain a long term mission plan becomes unaffordable for human planners due to the complexity of computing the huge number of possible combinations for finding an optimum solution. In this contribution we present a long term mission planning tool based on Genetic Algorithms, which are focused on solving optimization problems such as the planning of several tasks. Specifically, the proposed tool finds a solution that highly optimizes the defined objectives, which are based on the maximization of the time spent on scientific observations and the scientific return (e.g., the coverage of the mission survey). The results obtained on the large experimental set up support that the proposed scheduler technology is robust and can function in a variety of scenarios, offering a competitive performance which does not depend on the collection of exoplanets to be observed. Specifically, the results show that, with the proposed tool, EChO uses 94% of the available time of the mission, so the amount of downtime is small, and it completes 98% of the targets.

Embedding systematic quality assessments in supportive supervision at primary healthcare level: application of an electronic Tool to Improve Quality of Healthcare in Tanzania.

Science.gov (United States)

Mboya, Dominick; Mshana, Christopher; Kessy, Flora; Alba, Sandra; Lengeler, Christian; Renggli, Sabine; Vander Plaetse, Bart; Mohamed, Mohamed A; Schulze, Alexander

2016-10-13

Assessing quality of health services, for example through supportive supervision, is essential for strengthening healthcare delivery. Most systematic health facility assessment mechanisms, however, are not suitable for routine supervision. The objective of this study is to describe a quality assessment methodology using an electronic format that can be embedded in supervision activities and conducted by council health staff. An electronic Tool to Improve Quality of Healthcare (e-TIQH) was developed to assess the quality of primary healthcare provision. The e-TIQH contains six sub-tools, each covering one quality dimension: infrastructure and equipment of the facility, its management and administration, job expectations, clinical skills of the staff, staff motivation and client satisfaction. As part of supportive supervision, council health staff conduct quality assessments in all primary healthcare facilities in a given council, including observation of clinical consultations and exit interviews with clients. Using a hand-held device, assessors enter data and view results in real time through automated data analysis, permitting immediate feedback to health workers. Based on the results, quality gaps and potential measures to address them are jointly discussed and actions plans developed. For illustrative purposes, preliminary findings from e-TIQH application are presented from eight councils of Tanzania for the period 2011-2013, with a quality score quality dimensions at baseline. Clinical practice was unsatisfactory in six councils, with more mixed results for availability of infrastructure and equipment, and for administration and management. In contrast, client satisfaction scored surprisingly high. Over time, each council showed a significant overall increase of 3-7 % in mean score, with the most pronounced improvements in staff motivation and job expectations. Given its comprehensiveness, convenient handling and automated statistical reports, e-TIQH enables

Placental transfer of maternally-derived IgA precludes the use of guthrie card eluates as a screening tool for primary immunodeficiency diseases.

Directory of Open Access Journals (Sweden)

Stephan Borte

Full Text Available There is a need for neonatal screening tools to improve the long-term clinical outcome of patients with primary immunodeficiency diseases (PID. Recently, a PCR-based screening method for both TRECs and KRECs using Guthrie card samples has been developed. However, the applicability of these excision circle assays is limited to patients with severe T or B cell lymphopenia (SCID, XLA and A-T, whereas the most common forms of PID are not detected. Absence of serum IgA is seen in a major fraction of patients with immunological defects. As serum IgA in newborns is considered to be of fetal origin, eluates from routinely collected dried blood spot samples might thus be suitable for identification of children with PID. To assess the applicability of such screening assays, stored Guthrie card samples were obtained from 47 patients with various forms of primary immunodeficiency diseases (SCID, XLA, A-T, HIGM and IgAD, 20 individuals with normal serum IgA levels born to IgA-deficient mothers and 51 matched healthy newborns. Surprisingly, normal serum IgA levels were found in all SCID, XLA, A-T and HIGM patients and, additionally, in all those IgAD patients born to IgA-sufficient mothers. Conversely, no serum IgA was found in any of the 16 IgAD patients born by IgA-deficient mothers. Moreover, half of the IgA-sufficient individuals born by IgA-deficient mothers also lacked IgA at birth whereas no IgA-deficient individuals were found among the controls. IgA in neonatal dried blood samples thus appears to be of both maternal and fetal origin and precludes its use as a reliable marker for neonatal screening of primary immunodeficiency diseases.

Placental transfer of maternally-derived IgA precludes the use of guthrie card eluates as a screening tool for primary immunodeficiency diseases.

Science.gov (United States)

Borte, Stephan; Janzi, Magdalena; Pan-Hammarström, Qiang; von Döbeln, Ulrika; Nordvall, Lennart; Winiarski, Jacek; Fasth, Anders; Hammarström, Lennart

2012-01-01

There is a need for neonatal screening tools to improve the long-term clinical outcome of patients with primary immunodeficiency diseases (PID). Recently, a PCR-based screening method for both TRECs and KRECs using Guthrie card samples has been developed. However, the applicability of these excision circle assays is limited to patients with severe T or B cell lymphopenia (SCID, XLA and A-T), whereas the most common forms of PID are not detected. Absence of serum IgA is seen in a major fraction of patients with immunological defects. As serum IgA in newborns is considered to be of fetal origin, eluates from routinely collected dried blood spot samples might thus be suitable for identification of children with PID. To assess the applicability of such screening assays, stored Guthrie card samples were obtained from 47 patients with various forms of primary immunodeficiency diseases (SCID, XLA, A-T, HIGM and IgAD), 20 individuals with normal serum IgA levels born to IgA-deficient mothers and 51 matched healthy newborns. Surprisingly, normal serum IgA levels were found in all SCID, XLA, A-T and HIGM patients and, additionally, in all those IgAD patients born to IgA-sufficient mothers. Conversely, no serum IgA was found in any of the 16 IgAD patients born by IgA-deficient mothers. Moreover, half of the IgA-sufficient individuals born by IgA-deficient mothers also lacked IgA at birth whereas no IgA-deficient individuals were found among the controls. IgA in neonatal dried blood samples thus appears to be of both maternal and fetal origin and precludes its use as a reliable marker for neonatal screening of primary immunodeficiency diseases.

Tool steel for cold worck niobium carbides

International Nuclear Information System (INIS)

Goldenstein, H.

1984-01-01

A tool steel was designed so as to have a microstructure with the matrix similar a cold work tool steel of D series, containing a dispersion of Niobium carbides, with no intention of putting Niobium in solution on the matrix. The alloy was cast, forged and heat treated. The alloy was easily forged; the primary carbide morfology, after forging, was faceted, tending to equiaxed. The hardness obtained was equivalent to the maximum hardness of a D-3 sttel when quenched from any temperature between 950 0 C, and 1200 0 , showing a very small sensitivy to the quenching temperature. (Author) [pt

Investigating Power System Primary and Secondary Reserve Interaction under High Wind Power Penetration

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yingchen [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tan, Jin [National Renewable Energy Lab. (NREL), Golden, CO (United States); Krad, Ibrahim [National Renewable Energy Lab. (NREL), Golden, CO (United States); Yang, Rui [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gevorgian, Vahan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ela, Erik [Electric Power Research Inst. (EPRI), Knoxville, TN (United States)

2016-12-01

Power system frequency needs to be maintained close to its nominal value at all times to successfully balance load and generation and maintain system reliability. Adequate primary frequency response and secondary frequency response are the primary forces to correct an energy imbalance at the second-to-minute level. As wind energy becomes a larger portion of the world's energy portfolio, there is an increased need for wind to provide frequency response. This paper addresses one of the major concerns about using wind for frequency regulation: the unknown factor of the interaction between primary and secondary reserves. The lack of a commercially available tool to model this has limited the energy industry's understanding of when the depletion of primary reserves will impact the performance of secondary response or vice versa. This paper investigates the issue by developing a multi-area frequency response integration tool with combined primary and secondary capabilities. The simulation is conducted in close coordination with economical energy scheduling scenarios to ensure credible simulation results.

Primary Tunnel Junction Thermometry

International Nuclear Information System (INIS)

Pekola, Jukka P.; Holmqvist, Tommy; Meschke, Matthias

2008-01-01

We describe the concept and experimental demonstration of primary thermometry based on a four-probe measurement of a single tunnel junction embedded within four arrays of junctions. We show that in this configuration random sample specific and environment-related errors can be avoided. This method relates temperature directly to Boltzmann constant, which will form the basis of the definition of temperature and realization of official temperature scales in the future

Experimental and Numerical Investigations of Applying Tip-bottomed Tool for Bending Advanced Ultra-high Strength Steel Sheet

Science.gov (United States)

Mitsomwang, Pusit; Borrisutthekul, Rattana; Klaiw-awoot, Ken; Pattalung, Aran

2017-09-01

This research was carried out aiming to investigate the application of a tip-bottomed tool for bending an advanced ultra-high strength steel sheet. The V-die bending experiment of a dual phase steel (DP980) sheet which had a thickness of 1.6 mm was executed using a conventional bending and a tip-bottomed punches. Experimental results revealed that the springback of the bent worksheet in the case of the tip-bottomed punch was less than that of the conventional punch case. To further discuss bending characteristics, a finite element (FE) model was developed and used to simulate the bending of the worksheet. From the FE analysis, it was found that the application of the tip-bottomed punch contributed the plastic deformation to occur at the bending region. Consequently, the springback of the worksheet reduced. In addition, the width of the punch tip was found to affect the deformation at the bending region and determined the springback of the bent worksheet. Moreover, the use of the tip-bottomed punch resulted in the apparent increase of the surface hardness of the bent worksheet, compared to the bending with the conventional punch.

Survey of experimental tests about progressive distortion

International Nuclear Information System (INIS)

Clement, Gerard.

1981-02-01

A procedure for evaluation of progressive distorsion experimental data has been set up in CEA. This procedure based on the effective primary stress concept, permits the establishment of a simple design rule. Various published experimental data have been used for verification, validation and generalization of design rule proposed. This rule is compared with existing codified rules (3 Sm, BREE, O'DONNEL and POROWSKI) [fr

Experimental investigation of system effects in stressed-skin elements

DEFF Research Database (Denmark)

Dela Stang, B.; Isaksson, T.; Hansson, M.

What kind of behaviour can be expected from stressed-skin elements at failure? To answer this question was a primary objective of the experimental investigation presented in this report. Systems of 3 roof units, each made of 5 parallel beams, have been tested for load-carrying capacity and behavi......What kind of behaviour can be expected from stressed-skin elements at failure? To answer this question was a primary objective of the experimental investigation presented in this report. Systems of 3 roof units, each made of 5 parallel beams, have been tested for load-carrying capacity...

Protocol for development and validation of a context-appropriate tool for assessing organisational readiness for change in primary health clinics in South Africa.

Science.gov (United States)

Brooke-Sumner, Carrie; Sorsdahl, Katherine; Lombard, Carl; Petersen-Williams, Petal; Myers, Bronwyn

2018-04-09

A large treatment gap for common mental disorders (such as depression) exists in South Africa. Comorbidity with other chronic diseases, including HIV and diseases of lifestyle, is an increasing public health concern globally. Currently, primary health facilities as points of care for those with chronic disease provide limited services for common mental disorders. Assessing organisational readiness for change (ORC) towards adopting health innovations (such as mental health services) using contextually appropriate measures is needed to facilitate implementation of these services. This study aims to investigate the validity of the Texas Christian University Organisational Readiness for Change (TCU-ORC) scale in the South African context. Subsequently, we will develop a shortened version of this scale. This study is nested within Project MIND, a multiyear randomised controlled trial that is testing two different approaches for integrating counselling for common mental disorders into chronic disease care. Although the modified, contextually appropriate ORC measure resulting from the proposed study will be developed in the context of integrating mental health into primary healthcare services, the potential for the tool to be generalised to further understanding barriers to any change being implemented in primary care settings is high. We will establish internal consistency (Cronbach's alpha coefficients), test-retest reliability (intraclass correlation coefficient) and construct validity of the long-form TCU-ORC questionnaire. Survey data will be collected from 288 clinical, management and operational staff from 24 primary health facilities where the Project MIND trial is implemented. A modified Delphi approach will assess the content validity of the TCU-ORC items and identify areas for potential adaptation and item reduction. Ethical approval has been granted by the South African Medical Research Council (Protocol ID EC004-2-2015, amendment of 20 August 2017). Results

Children's health care assistance according to their families: a comparison between models of Primary Care

Directory of Open Access Journals (Sweden)

Vanessa Bertoglio Comassetto Antunes de Oliveira

2015-02-01

Full Text Available OBJECTIVE To compare the health assistance models of Basic Traditional Units (UBS with the Family Health Strategy (ESF units for presence and extent of attributes of Primary Health Care (APS, specifically in the care of children. METHOD A cross-sectional study of a quantitative approach with families of children attended by the Public Health Service of Colombo, Paraná. The Primary Care Assessment Tool (PCA-Tool was applied to parents of 482 children, 235 ESF units and 247 UBS units covering all primary care units of the municipality, between June and July 2012. The results were analyzed according to the PCA-Tool manual. RESULTS ESF units reached a borderline overall score for primary health care standards. However, they fared better in their attributes of Affiliation, Integration of care coordination, Comprehensiveness, Family Centeredness and Accessibility of use, while the attributes of Community Guidance/Orientation, Coordination of Information Systems, Longitudinality and Access attributes were rated as insufficient for APS. UBS units had low scores on all attributes. CONCLUSION The ESF units are closer to the principles of APS (Primary Health Care, but there is need to review actions of child care aimed at the attributes of APS in both care models, corroborating similar studies from other regions of Brazil.

Managing obesity in primary care.

Science.gov (United States)

Goldie, Christine; Brown, Jenny

Obesity is a complex problem and often difficult to tackle in primary care. A year-long pilot of a practice nurse-led scheme that used a holistic approach towards self-care in obesity management was set up to reduce the cardiovascular risk of patients who were obese and improve their quality of life. This person-centred approach may offer an important tool in the management of these patients in the GP surgery.

Microelectrodes as novel research tools for environmental biofilm studies

International Nuclear Information System (INIS)

Yu, T.; Lu, R.; Bishop, L.

2002-01-01

Biofilm processes are widely utilized in environmental engineering for biodegradation of contaminated waters, gases and soils. It is important to understand the structure and functions of biofilms. Microelectrodes are novel experimental tools for environmental biofilm studies. The authors reviewed the techniques of oxygen, sulfide, redox potential and pH microelectrode. These microelectrodes have tip diameters of 3 to 20 μm, resulting a high spatial resolution. They enable us directly measure the chemical conditions as results of microbial activities in biofilms. The authors also reported the laboratory and field studies of wastewater biofilms using microelectrode techniques. The results of these studies provided experimental evidence on the stratification of microbial processes and the associated redox potential change in wastewater biofilms: (1) The oxygen penetration depth was only a fraction of the biofilm thickness. This observation, first made under laboratory conditions, has been confirmed under field conditions. (2) The biofilms with both aerobic oxidation and sulfate reduction had a clearly stratified structure. This was evidenced by a sharp decrease of redox potential near the interface between the aerobic zone and the sulfate reduction zone within the biofilm. In this type of biofilms, aerobic oxidation took place only in a shallow layer near the biofilm surface and sulfate reduction occurred in the deeper anoxic zone. (3) The redox potential changed with the shift of primary microbial process in biofilms, indicating that it is possible to use redox potential to help illustrate the structure and functions of biofilms. (author)

An empowerment-based approach to developing innovative e-health tools for self-management

NARCIS (Netherlands)

Alpay, L.; Boog, P. van der; Dumaij, A.

2011-01-01

E-health is seen as an important technological tool in achieving self-management; however, there is little evidence of how effective e-health is for self-management. Example tools remain experimental and there is limited knowledge yet about the design, use, and effects of this class of tools. By way

Quality of Health Assistants in primary Health centres in Rural Maharashtra, India

Directory of Open Access Journals (Sweden)

Enakshi Ganguly

2013-01-01

Full Text Available Introduction Health assistants are important functionaries of the primary health care system in India. Their role is supervision of field-based services among other things. A quality assurance mechanism for these health assistants is lacking. The present study was undertaken with the objectives of developing a tool to assess the quality of health assistants in primary health centres (PHCs and to assess their quality using this tool. Methodology Health assistants from three PHCs in the Wardha district of India were observed for a year using a tool developed from primary health care management Aavancement program modules. Data was collected by direct observation, interview, and review of records for quality of activities. Results Staff strength of health assistants was 87.5%. None of the health assistants were clear about their job descriptions. A supervisory schedule for providing supportive supervision to auxiliary nurse midwives (ANMs was absent; most field activities pertaining to maternal and child health received poor focus. Monthly meetings lacked a clear agenda, and comments on quality improvement of services provided by the ANMs were missing. Conclusion Continuous training with sensitization on quality issues is required to improve the unsatisfactory quality.

Translating and validating a Training Needs Assessment tool into Greek

OpenAIRE

Markaki, Adelais; Antonakis, Nikos; Hicks, Carolyn M; Lionis, Christos

2007-01-01

Abstract Background The translation and cultural adaptation of widely accepted, psychometrically tested tools is regarded as an essential component of effective human resource management in the primary care arena. The Training Needs Assessment (TNA) is a widely used, valid instrument, designed to measure professional development needs of health care professionals, especially in primary health care. This study aims to describe the translation, adaptation and validation of the TNA questionnaire...

[Psychometric validation in Spanish of the Brazilian short version of the Primary Care Assessment Tools-users questionnaire for the evaluation of the orientation of health systems towards primary care].

Science.gov (United States)

Vázquez Peña, Fernando; Harzheim, Erno; Terrasa, Sergio; Berra, Silvina

2017-02-01

To validate the Brazilian short version of the PCAT for adult patients in Spanish. Analysis of secondary data from studies made to validate the extended version of the PCAT questionnaire. City of Córdoba, Argentina. Primary health care. The sample consisted of 46% of parents, whose children were enrolled in secondary education in three institutes in the city of Cordoba, and the remaining 54% were adult users of the National University of Cordoba Health Insurance. Pearson's correlation coefficient comparing the extended and short versions. Goodness-of-fit indices in confirmatory factor analysis, composite reliability, average variance extracted, and Cronbach's alpha values, in order to assess the construct validity and the reliability of the short version. The values of Pearson's correlation coefficient between this short version and the long version were high .818 (Pmedia extracted: .3306, since 3 variables had weak factorials loads. The Cronbach's alpha was acceptable (.85). The short version of the PCAT-users developed in Brazil showed an acceptable psychometric performance in Spanish as a quick assessment tool, in a comparative study with the extended version. Copyright © 2016 Elsevier España, S.L.U. All rights reserved.

Uncertainty in techno-economic estimates of cellulosic ethanol production due to experimental measurement uncertainty

Directory of Open Access Journals (Sweden)

Vicari Kristin J

2012-04-01

Full Text Available Abstract Background Cost-effective production of lignocellulosic biofuels remains a major financial and technical challenge at the industrial scale. A critical tool in biofuels process development is the techno-economic (TE model, which calculates biofuel production costs using a process model and an economic model. The process model solves mass and energy balances for each unit, and the economic model estimates capital and operating costs from the process model based on economic assumptions. The process model inputs include experimental data on the feedstock composition and intermediate product yields for each unit. These experimental yield data are calculated from primary measurements. Uncertainty in these primary measurements is propagated to the calculated yields, to the process model, and ultimately to the economic model. Thus, outputs of the TE model have a minimum uncertainty associated with the uncertainty in the primary measurements. Results We calculate the uncertainty in the Minimum Ethanol Selling Price (MESP estimate for lignocellulosic ethanol production via a biochemical conversion process: dilute sulfuric acid pretreatment of corn stover followed by enzymatic hydrolysis and co-fermentation of the resulting sugars to ethanol. We perform a sensitivity analysis on the TE model and identify the feedstock composition and conversion yields from three unit operations (xylose from pretreatment, glucose from enzymatic hydrolysis, and ethanol from fermentation as the most important variables. The uncertainty in the pretreatment xylose yield arises from multiple measurements, whereas the glucose and ethanol yields from enzymatic hydrolysis and fermentation, respectively, are dominated by a single measurement: the fraction of insoluble solids (fIS in the biomass slurries. Conclusions We calculate a $0.15/gal uncertainty in MESP from the TE model due to uncertainties in primary measurements. This result sets a lower bound on the error bars of

The renal transcriptome in experimental hypertension

NARCIS (Netherlands)

Wesseling, S.

2007-01-01

The renal transcriptome in experimental hypertension The kidneys importantly determine blood pressure. Kidney dysfunction can result in hypertension, which in turn leads to renal damage. In primary hypertension the cause is unknown. The condition is polygenic, however, which genetic defects cause

Identification and adjustment of experimental occlusal interference using functional magnetic resonance imaging.

Science.gov (United States)

Oda, Masafumi; Yoshino, Kenichi; Tanaka, Tatsurou; Shiiba, Shunji; Makihara, Eri; Miyamoto, Ikuya; Nogami, Shinnosuke; Kito, Shinji; Wakasugi-Sato, Nao; Matsumoto-Takeda, Shinobu; Nishimura, Shun; Murakami, Keita; Koga, Masahiro; Kawagishi, Shigenori; Yoshioka, Izumi; Masumi, Shin-Ichi; Kimura, Mitsutaka; Morimoto, Yasuhiro

2014-10-10

The purpose of this study was to use functional magnetic resonance imaging (fMRI) to quantify changes in brain activity during experimental occlusal interference. Fourteen healthy volunteers performed a rhythmical tapping occlusion task with experimental occlusal interference of the right molar tooth at 0 mm (no occlusion), 0.5 mm, and 0.75 mm. The blood-oxygen-level dependent (BOLD) signal was quantified using statistical parametric mapping and compared between rest periods and task periods. In tapping tasks with experimental occlusal interference of 0.75 mm or 0.5 mm, there was clear activation of the contralateral teeth-related primary sensory cortex and Brodmann's area 46. At 0 and 30 minutes after removal of the experimental occlusal interference, the activation clearly appeared in the bilateral teeth-related primary sensory cortices and Brodmann's area 46. At 60 minutes after the removal of the experimental occlusal interference, the activation of Brodmann's area 46 had disappeared, and only the bilateral teeth-related primary sensory cortices were active. The present results suggest that adjustments for experimental occlusal interference can be objectively evaluated using fMRI. We expect that this method of evaluating adjustments in occlusal interference, combined with fMRI and the tapping task, could be applied clinically in the future.

Experimental and numerical study on heat transfer and pressure drop performance of Cross-Wavy primary surface channel

International Nuclear Information System (INIS)

Ma, Ting; Du, Lin-xiu; Sun, Ning; Zeng, Min; Sundén, Bengt; Wang, Qiu-wang

2016-01-01

Highlights: • Naphthalene sublimation experiments were performed for Cross-Wavy channels. • Entrance region has a small effect on unit-averaged heat transfer coefficient of Cross-Wavy channels. • Correlations of Nusselt number and friction factor in Cross-Wavy channel were obtained. • Similar Cross-Wavy channels have similar thermal hydraulic performance. - Abstract: The Cross-Wavy primary surface heat exchanger is one of the most promising candidates for microturbine recuperators. In this paper, naphthalene sublimation experiments are performed for Cross-Wavy channels in a wind tunnel. The experimental results indicate that the entrance region has a small effect on the unit-averaged heat transfer coefficient of whole Cross-Wavy channels. Correlations of Nusselt number and friction factor in the Cross-Wavy channel are obtained. However, only the Cross-Wavy channel with a large equivalent diameter is tested because the actual Cross-Wavy channels are very complicated and small. Therefore, based on the similarity rules, five Cross-Wavy channels with similar structures but different equivalent diameters are further investigated by numerical simulations. The numerical results indicate that the Cross-Wavy channels with similar structures but different equivalent diameters have similar thermal-hydraulic performance in the studied Reynolds number range.

INCA project for investigation of primary cosmic radiation spectrum

International Nuclear Information System (INIS)

Aleksandrov, K.V.; Erlykin, A.D.; Zhdanov, G.B.

2002-01-01

The scientific purposes of the INCA project and application of the ionization-neutron calorimeter for direct measurements of the cosmic rays spectrum and composition in the knee area and the primary electrons spectrum by 10 14 - 10 13 eV are discussed. The new effective method for the primary electrons and protons separation with the complex rejection coefficient of 10 -5 - 10 -6 is proposed for studying the primary electrons spectrum by E e > 1 TeV. The experimental and calculation data are in good agreement [ru

Validation of brief screening tools for depressive and alcohol use disorders among TB and HIV patients in primary care in Zambia

Directory of Open Access Journals (Sweden)

Patel Vikram

2011-05-01

suitable mental health screening tools for use among TB and ART patients in primary care in Zambia.

Using CFD as Rocket Injector Design Tool: Recent Progress at Marshall Space Flight Center

Science.gov (United States)

Tucker, Kevin; West, Jeff; Williams, Robert; Lin, Jeff; Rocker, Marvin; Canabal, Francisco; Robles, Bryan; Garcia, Robert; Chenoweth, James

2003-01-01

The choice of tools used for injector design is in a transitional phase between exclusive reliance on the empirically based correlations and extensive use of computational fluid dynamics (CFD). The Next Generation Launch Technology (NGLT) Program goals emphasizing lower costs and increased reliability have produced a need to enable CFD as an injector design tool in a shorter time frame. This is the primary objective of the Staged Combustor Injector Technology Task currently under way at Marshall Space Flight Center (MSFC). The documentation of this effort begins with a very brief status of current injector design tools. MSFC's vision for use of CFD as a tool for combustion devices design is stated and discussed with emphasis on the injector. The concept of the Simulation Readiness Level (SRL), comprised of solution fidelity, robustness and accuracy, is introduced and discussed. This quantitative measurement is used to establish the gap between the current state of demonstrated capability and that necessary for regular use in the design process. MSFC's view of the validation process is presented and issues associated with obtaining the necessary data are noted and discussed. Three current experimental efforts aimed at generating validation data are presented. The importance of uncertainty analysis to understand the data quality is also demonstrated. First, a brief status of current injector design tools is provided as context for the current effort. Next, the MSFC vision for using CFD as an injector design tool is stated. A generic CFD-based injector design methodology is also outlined and briefly discussed. Three areas where MSFC is using injector CFD analyses for program support will be discussed. These include the Integrated Powerhead Development (IPD) engine which uses hydrogen and oxygen propellants in a full flow staged combustion (FFSC) cycle and the TR-107 and the RS84 engine both of which use RP-1 and oxygen in an ORSC cycle. Finally, an attempt is made to

Characterization of primary geochemical haloes for gold exploration at the Huanxiangwa gold deposit, China

NARCIS (Netherlands)

Wang, Changming; Carranza, E.J.M; Zhang, Shouting; Zhang, Jing; Liu, Xiaoji Liu; Zhang, Da; Sun, Xiang; Duan, Cunji

2013-01-01

Recognition of primary geochemical haloes is one of the most important tools for exploring undiscovered mineral resources. This tool is being routinely applied in exploration programs at the Huanxiangwa gold deposit, Xiong'er Mountains, China. Sampling of unweathered rock for multi-element analysis

Experimental system model of a primary active fluid

International Nuclear Information System (INIS)

Deseigne, Julien

2010-01-01

Collective motion, such as flocks of birds or shoals of fish, is ubiquitous in nature. Such fundamentally out-of-equilibrium phenomena may be described with the new conceptual background of polar active matter, a system of polar particles which enables to use provided energy in order to move in their own directions. A 2D experimental system of vibrated polar disks that interact only by contact has been set up. These disks behave as random walkers, whose trajectories are characterized by a persistence length greater than their size and controlled by the angular fluctuations of their polarity. The interplay between the hard-core repulsion and the persistence of the motion leads to complex alignment modes. For instance, only 10 pc of the binary collisions correspond to an effective ferromagnetic alignment. Yet, spontaneous collective motion inside the system characterized by giant fluctuations of density have been observed. These results reveal the robustness of the polar order observed in theoretical and numerical models of 2D polar active matter on substrate

Reliability concepts applied to cutting tool change time

Energy Technology Data Exchange (ETDEWEB)

Patino Rodriguez, Carmen Elena, E-mail: cpatino@udea.edu.c [Department of Industrial Engineering, University of Antioquia, Medellin (Colombia); Department of Mechatronics and Mechanical Systems, Polytechnic School, University of Sao Paulo, Sao Paulo (Brazil); Francisco Martha de Souza, Gilberto [Department of Mechatronics and Mechanical Systems, Polytechnic School, University of Sao Paulo, Sao Paulo (Brazil)

2010-08-15

This paper presents a reliability-based analysis for calculating critical tool life in machining processes. It is possible to determine the running time for each tool involved in the process by obtaining the operations sequence for the machining procedure. Usually, the reliability of an operation depends on three independent factors: operator, machine-tool and cutting tool. The reliability of a part manufacturing process is mainly determined by the cutting time for each job and by the sequence of operations, defined by the series configuration. An algorithm is presented to define when the cutting tool must be changed. The proposed algorithm is used to evaluate the reliability of a manufacturing process composed of turning and drilling operations. The reliability of the turning operation is modeled based on data presented in the literature, and from experimental results, a statistical distribution of drilling tool wear was defined, and the reliability of the drilling process was modeled.

Reliability concepts applied to cutting tool change time

International Nuclear Information System (INIS)

Patino Rodriguez, Carmen Elena; Francisco Martha de Souza, Gilberto

2010-01-01

This paper presents a reliability-based analysis for calculating critical tool life in machining processes. It is possible to determine the running time for each tool involved in the process by obtaining the operations sequence for the machining procedure. Usually, the reliability of an operation depends on three independent factors: operator, machine-tool and cutting tool. The reliability of a part manufacturing process is mainly determined by the cutting time for each job and by the sequence of operations, defined by the series configuration. An algorithm is presented to define when the cutting tool must be changed. The proposed algorithm is used to evaluate the reliability of a manufacturing process composed of turning and drilling operations. The reliability of the turning operation is modeled based on data presented in the literature, and from experimental results, a statistical distribution of drilling tool wear was defined, and the reliability of the drilling process was modeled.

Efficient primary and parametric resonance excitation of bistable resonators

KAUST Repository

Ramini, Abdallah

2016-09-12

We experimentally demonstrate an efficient approach to excite primary and parametric (up to the 4th) resonance of Microelectromechanical system MEMS arch resonators with large vibrational amplitudes. A single crystal silicon in-plane arch microbeam is fabricated such that it can be excited axially from one of its ends by a parallel-plate electrode. Its micro/nano scale vibrations are transduced using a high speed camera. Through the parallel-plate electrode, a time varying electrostatic force is applied, which is converted into a time varying axial force that modulates dynamically the stiffness of the arch resonator. Due to the initial curvature of the structure, not only parametric excitation is induced, but also primary resonance. Experimental investigation is conducted comparing the response of the arch near primary resonance using the axial excitation to that of a classical parallel-plate actuation where the arch itself forms an electrode. The results show that the axial excitation can be more efficient and requires less power for primary resonance excitation. Moreover, unlike the classical method where the structure is vulnerable to the dynamic pull-in instability, the axial excitation technique can provide large amplitude motion while protecting the structure from pull-in. In addition to primary resonance, parametrical resonances are demonstrated at twice, one-half, and two-thirds the primary resonance frequency. The ability to actuate primary and/or parametric resonances can serve various applications, such as for resonator based logic and memory devices. (C) 2016 Author(s). All article content, except where otherwise noted, is licensed under a Creative Commons Attribution (CC BY) license

A TOOL FOR EMOTIONAL USER EXPERIENCE ASSESSMENT OF WEB-BASED MEDICAL SERVICES

OpenAIRE

Alexander Nikov; Tramaine Alaina Gumaia

2016-01-01

Emotional User Experience Design (eUXD) has become increasingly important for web-based services. The primary objective of this study is to enable users to use websites that are easy to understand and operate and pleasing to use. A checklist tool for an emotional user experience (eUX) assessment that supports web-based medical services is proposed. This tool measures user moods while using medical services’ websites. The tool allocates emotive design-oriented problems and thus defines relevan...

Validating the CORE-10 as a mental health screening tool for prisoners

OpenAIRE

Lewis, Gwen

2016-01-01

Background: Few mental health screening tools have been validated with prisoners and existing tools, do not assess severity of need in line with contemporary stepped care service models. \\ud \\ud Aims: The current research aims to assess the CORE-10’s psychometric reliability, validity and predictive accuracy as a screening tool for common (primary care) and severe (secondary care) mental health problems in prisoners. \\ud \\ud Method: Cross –sectional study of 150 prisoners. All participants co...

Robotic edge machining using elastic abrasive tool

Science.gov (United States)

Sidorova, A. V.; Semyonov, E. N.; Belomestnykh, A. S.

2018-03-01

The article describes a robotic center designed for automation of finishing operations, and analyzes technological aspects of an elastic abrasive tool applied for edge machining. Based on the experimental studies, practical recommendations on the application of the robotic center for finishing operations were developed.

Implementation of a Care Pathway for Primary Palliative Care in 5 research clusters in Belgium: quasi-experimental study protocol and innovations in data collection (pro-SPINOZA).

Science.gov (United States)

Leysen, Bert; Van den Eynden, Bart; Gielen, Birgit; Bastiaens, Hilde; Wens, Johan

2015-09-28

Starting with early identification of palliative care patients by general practitioners (GPs), the Care Pathway for Primary Palliative Care (CPPPC) is believed to help primary health care workers to deliver patient- and family-centered care in the last year of life. The care pathway has been pilot-tested, and will now be implemented in 5 Belgian regions: 2 Dutch-speaking regions, 2 French-speaking regions and the bilingual capital region of Brussels. The overall aim of the CPPPC is to provide better quality of primary palliative care, and in the end to reduce the hospital death rate. The aim of this article is to describe the quantitative design and innovative data collection strategy used in the evaluation of this complex intervention. A quasi-experimental stepped wedge cluster design is set up with the 5 regions being 5 non-randomized clusters. The primary outcome is reduced hospital death rate per GPs' patient population. Secondary outcomes are increased death at home and health care consumption patterns suggesting high quality palliative care. Per research cluster, GPs will be recruited via convenience sampling. These GPs -volunteering to be involved will recruit people with reduced life expectancy and their informal care givers. Health care consumption data in the last year of life, available for all deceased people having lived in the research clusters in the study period, will be used for comparison between patient populations of participating GPs and patient populations of non-participating GPs. Description of baseline characteristics of participating GPs and patients and monitoring of the level of involvement by GPs, patients and informal care givers will happen through regular, privacy-secured web-surveys. Web-survey data and health consumption data are linked in a secure way, respecting Belgian privacy laws. To evaluate this complex intervention, a quasi-experimental stepped wedge cluster design has been set up. Context characteristics and involvement

FFTBM and primary pressure acceptance criterion

International Nuclear Information System (INIS)

Prosek, A.

2004-01-01

When thermalhydraulic computer codes are used for simulation in the area of nuclear engineering the question is how to conduct an objective comparison between the code calculation and measured data. To answer this the fast Fourier transform based method (FFTBM) was developed. When the FFTBM method was developed the acceptance criteria for primary pressure and total accuracy were set. In the recent study the FFTBM method was used for accuracy quantification of RD-14M large LOCA test B9401 calculations. The blind accuracy analysis indicated good total accuracy while the primary pressure criterion was not fulfilled. The objective of the study was therefore to investigate the reasons for not fulfilling the primary pressure acceptance criterion and the applicability of the criterion to experimental facilities simulating heavy water reactor. The results of the open quantitative analysis showed that sensitivity analysis for influence parameters provide sufficient information to judge in which calculation the accuracy of primary pressure is acceptable. (author)

Feeder replacement tooling and processes

International Nuclear Information System (INIS)

Mallozzi, R.; Goslin, R.; Pink, D.; Askari, A.

2008-01-01

Primary heat transport system feeder integrity has become a concern at some CANDU nuclear plants as a result of thinning caused by flow accelerated corrosion (FAC). Feeder inspections are indicating that life-limiting wall thinning can occur in the region between the Grayloc hub weld and second elbow of some outlet feeders. In some cases it has become necessary to replace thinned sections of affected feeders to restore feeder integrity to planned end of life. Atomic Energy of Canada Limited (AECL) and Babcock and Wilcox Canada Ltd. (B and W) have developed a new capability for replacement of single feeders at any location on the reactor face without impacting or interrupting operation of neighbouring feeders. This new capability consists of deploying trained crews with specialized tools and procedures for feeder replacements during planned outages. As may be expected, performing single feeder replacement in the congested working environment of an operational CANDU reactor face involves overcoming many challenges with respect to access to feeders, available clearances for tooling, and tooling operation and performance. This paper describes some of the challenges encountered during single feeder replacements and actions being taken by AECL and B and W to promote continuous improvement of feeder replacement tooling and processes and ensure well-executed outages. (author)

Investigation of the effect of tool edge geometry upon cutting variables, tool wear and burr formation using finite element simulation - A progress report

International Nuclear Information System (INIS)

Sartkulvanich, Partchapol; Al-Zkeri, Ibrahim; Yen Yungchang; Altan, Taylan

2004-01-01

This paper summarizes some of the progress made on FEM simulations of metal cutting processes conducted at the Engineering Research Center (ERC/NSM). Presented research focuses on the performance of various cutting edge geometries (hone and chamfer edges) for different tool materials and specifically on: 1) the effect of round and chamfer edge geometries on the cutting variables in machining carbon steels and 2) the effect of the edge hone size upon the flank wear and burr formation behavior in face milling of A356-T6 aluminum alloy. In the second task, an innovative design of edge preparation with varying hone size around the tool nose is also explored using FEM.In order to model three-dimensional conventional turning and face milling with two-dimensional orthogonal cutting simulations, 2D simulation cross-sections consisting of the cutting speed direction and chip flow direction are selected at different locations along the tool nose radius. Then the geometries of the hone and chamfer edges and their associated tool angles as well as uncut chip thickness are determined on these planes and employed in cutting simulations. The chip flow direction on the tool rake face are obtained by examining the wear grooves on the experimental inserts or estimated by using Oxley's approximation theory of oblique cutting. Simulation results are compared with the available experimental results (e.g. cutting forces) both qualitatively and quantitatively

Motif enrichment tool.

Science.gov (United States)

Blatti, Charles; Sinha, Saurabh

2014-07-01

The Motif Enrichment Tool (MET) provides an online interface that enables users to find major transcriptional regulators of their gene sets of interest. MET searches the appropriate regulatory region around each gene and identifies which transcription factor DNA-binding specificities (motifs) are statistically overrepresented. Motif enrichment analysis is currently available for many metazoan species including human, mouse, fruit fly, planaria and flowering plants. MET also leverages high-throughput experimental data such as ChIP-seq and DNase-seq from ENCODE and ModENCODE to identify the regulatory targets of a transcription factor with greater precision. The results from MET are produced in real time and are linked to a genome browser for easy follow-up analysis. Use of the web tool is free and open to all, and there is no login requirement. ADDRESS: http://veda.cs.uiuc.edu/MET/. © The Author(s) 2014. Published by Oxford University Press on behalf of Nucleic Acids Research.

Advanced free-form micro tooling

DEFF Research Database (Denmark)

Tosello, Guido; Gavillet, J.

2011-01-01

-beam lithography and nano imprinting lithography [Che05][Che09] have high manufacturing cost and a low throughput. The aim was obtain large tool area with nano structures patterning without using energy intensive nano machining (e.g. focus ion beam, X-ray lithography, etc) but, instead, by exploiting the advantage......The present deliverable contains the report of the work and results achieved within the framework of WP 2.2 in Tasks 2.2.4 “Advanced free-form micro tooling” in experimental research done regarding practical applications of methods of applying nano structures to tooling solutions. As part of Task 2.......2.4, tests based on three different chemical-based-batch techniques to establish surface nano (i.e. sub-μm) structures on large tools area were performed. The three approached regarded: o Scheme 1  The use of Ø500nm nanobeads deposition for direct patterning of a Ø4inch. silicon wafer and subsequent nickel...

Evaluation of static analysis tools used to assess software important to nuclear power plant safety

Energy Technology Data Exchange (ETDEWEB)

Ourghanlian, Alain [EDF Lab CHATOU, Simulation and Information Technologies for Power Generation Systems Department, EDF R and D, Cedex (France)

2015-03-15

We describe a comparative analysis of different tools used to assess safety-critical software used in nuclear power plants. To enhance the credibility of safety assessments and to optimize safety justification costs, Electricit e de France (EDF) investigates the use of methods and tools for source code semantic analysis, to obtain indisputable evidence and help assessors focus on the most critical issues. EDF has been using the PolySpace tool for more than 10 years. Currently, new industrial tools based on the same formal approach, Abstract Interpretation, are available. Practical experimentation with these new tools shows that the precision obtained on one of our shutdown systems software packages is substantially improved. In the first part of this article, we present the analysis principles of the tools used in our experimentation. In the second part, we present the main characteristics of protection-system software, and why these characteristics are well adapted for the new analysis tools.

Drilling of optical glass with electroplated diamond tools

Science.gov (United States)

Wang, A. J.; Luan, C. G.; Yu, A. B.

2010-10-01

K9 optical glass drilling experiments were carried out. Bright nickel electroplated diamond tools with small slots and under heat treatment in different temperature were fabricated. Scan electro microscope was applied to analyze the wear of electroplated diamond tool. The material removal rate and grinding ratio were calculated. Machining quality was observed. Bond coating hardness was measured. The experimental results show that coolant is needed for the drilling processes of optical glasses. Heat treatment temperature of diamond tool has influence on wearability of diamond tool and grinding ratio. There were two wear types of electroplated diamond tool, diamond grit wear and bond wear. With the machining processes, wear of diamond grits included fracture, blunt and pull-out, and electroplated bond was gradually worn out. High material removal rates could be obtained by using diamond tool with suitable slot numbers. Bright nickel coating bond presents smallest grains and has better mechanical properties. Bright nickel electroplated diamond tool with slot structure and heat treatment under 200°C was suitable for optical glass drilling.

Common primary headaches in pregnancy

Directory of Open Access Journals (Sweden)

Anuradha Mitra

2015-01-01

Full Text Available Headache is a very common problem in pregnancy. Evaluation of a complaint of headache requires categorizing it as primary or secondary. Migrainous headaches are known to be influenced by fluctuation of estrogen levels with high levels improving it and low levels deteriorating the symptoms. Tension-type Headaches (TTHs are the most common and usually less severe types of headache with female to male ratio 3:1. Women known to have primary headache before conception who present with a headache that is different from their usual headache, or women not known to have primary headache before conception who present with new-onset of headache during pregnancy need neurologic assessments for potential secondary cause for their headache. In addition to proper history and physical examination, both non-contrast computed tomography (CT and Magnetic Resonance Imaging (MRI are considered safe to be performed in pregnant women when indicated. Treatment of abortive and prophylactic therapy should include non-pharmacologic tools, judicious use of drugs which are safe for mother and fetus.

Cardiovascular Risk in Primary Hyperaldosteronism.

Science.gov (United States)

Prejbisz, A; Warchoł-Celińska, E; Lenders, J W M; Januszewicz, A

2015-12-01

After the first cases of primary aldosteronism were described and characterized by Conn, a substantial body of experimental and clinical evidence about the long-term effects of excess aldosterone on the cardiovascular system was gathered over the last 5 decades. The prevalence of primary aldosteronism varies considerably between different studies among hypertensive patients, depending on patient selection, the used diagnostic methods, and the severity of hypertension. Prevalence rates vary from 4.6 to 16.6% in those studies in which confirmatory tests to diagnose primary aldosteronism were used. There is also growing evidence indicating that prolonged exposure to elevated aldosterone concentrations is associated with target organ damage in the heart, kidney, and arterial wall, and high cardiovascular risk in patients with primary aldosteronism. Therefore, the aim of treatment should not be confined to BP normalization and hypokalemia correction, but rather should focus on restoring the deleterious effects of excess aldosterone on the cardiovascular system. Current evidence convincingly demonstrates that both surgical and medical treatment strategies beneficially affect cardiovascular outcomes and mortality in the long term. Further studies can be expected to provide better insight into the relationship between cardiovascular risk and complications and the genetic background of primary aldosteronism. © Georg Thieme Verlag KG Stuttgart · New York.

New software tools for enhanced precision in robot-assisted laser phonomicrosurgery.

Science.gov (United States)

Dagnino, Giulio; Mattos, Leonardo S; Caldwell, Darwin G

2012-01-01

This paper describes a new software package created to enhance precision during robot-assisted laser phonomicrosurgery procedures. The new software is composed of three tools for camera calibration, automatic tumor segmentation, and laser tracking. These were designed and developed to improve the outcome of this demanding microsurgical technique, and were tested herein to produce quantitative performance data. The experimental setup was based on the motorized laser micromanipulator created by Istituto Italiano di Tecnologia and the experimental protocols followed are fully described in this paper. The results show the new tools are robust and effective: The camera calibration tool reduced residual errors (RMSE) to 0.009 ± 0.002 mm under 40× microscope magnification; the automatic tumor segmentation tool resulted in deep lesion segmentations comparable to manual segmentations (RMSE= 0.160 ± 0.028 mm under 40× magnification); and the laser tracker tool proved to be reliable even during cutting procedures (RMSE= 0.073 ± 0.023 mm under 40× magnification). These results demonstrate the new software package can provide excellent improvements to the previous microsurgical system, leading to important enhancements in surgical outcome.

The secret bread tests: selective primary health care or experimentation on human-beings?

Science.gov (United States)

Kamien, M

1987-01-01

This is a case history which describes an attempt to fortify the bread of Australian Aborigines in an isolated area of New South Wales. The medically successful intervention was accomplished by the publication of scientific enquiry and by attention to the culture of Aborigines. Paradoxically the long-term failure of the project was also due to the power of the written word and the neglect of the culture of the more densely populated and politically dominant white community. The need for doctors to be aware of the different approaches of primary health care and selective primary health care is stressed so that a general practitioner who provides health care for minority groups of the Fourth World can better define his role and relevance.

A Human-Centered Command and Control (C2) Assessment of an Experimental Campaign Planning Tool

Science.gov (United States)

2014-04-01

Figure 10. Total minutes within team interactions by individual team members. .........................14  Figure 11. NASA TLX workload results for...tool. Members of both teams completed the National Aeronautics and Space Administration (NASA) Task Load Index ( TLX ) subjective evaluation of their...Ends Break Lunch Break Break 6 NASA TLX is a subjective workload assessment tool that allows users to perform subjective workload assessments on

Validation of equilibrium tools on the COMPASS tokamak

Energy Technology Data Exchange (ETDEWEB)

Urban, J., E-mail: urban@ipp.cas.cz [Institute of Plasma Physics ASCR, Za Slovankou 3, 182 00 Praha 8 (Czech Republic); Appel, L.C. [CCFE, Culham Science Centre, Abingdon, Oxfordshire (United Kingdom); Artaud, J.F. [CEA, IRFM, F-13108 Saint Paul Lez Durance (France); Faugeras, B. [Laboratoire J.A. Dieudonné, UMR 7351, Université de Nice Sophia-Antipolis, Parc Valrose, 06108 Nice Cedex 02 (France); Havlicek, J. [Institute of Plasma Physics ASCR, Za Slovankou 3, 182 00 Praha 8 (Czech Republic); Department of Surface and Plasma Science, Faculty of Mathematics and Physics, Charles University in Prague, V Holešovičkách 2, 180 00 Praha 8 (Czech Republic); Komm, M. [Institute of Plasma Physics ASCR, Za Slovankou 3, 182 00 Praha 8 (Czech Republic); Lupelli, I. [CCFE, Culham Science Centre, Abingdon, Oxfordshire (United Kingdom); Peterka, M. [Institute of Plasma Physics ASCR, Za Slovankou 3, 182 00 Praha 8 (Czech Republic); Department of Surface and Plasma Science, Faculty of Mathematics and Physics, Charles University in Prague, V Holešovičkách 2, 180 00 Praha 8 (Czech Republic)

2015-10-15

Highlights: • Three equilibrium codes—EFIT++, FREEBIE and VacTH—have been successfully set up and validated on COMPASS. • FREEBIE can predictively calculate the equilibrium and corresponding poloidal field coil currents. • EFIT++ can reconstruct equilibria generated by FREEBIE from synthetic, optionally noisy diagnostic data. • VacTH is a promising tool for real time plasma shape reconstruction. • Optimized parameters are estimated for EFIT++ and VacTH by a statistical analysis. - Abstract: Various MHD (magnetohydrodynamic) equilibrium tools, some of which being recently developed or considerably updated, are used on the COMPASS tokamak at IPP Prague. MHD equilibrium is a fundamental property of the tokamak plasma, whose knowledge is required for many diagnostics and modelling tools. Proper benchmarking and validation of equilibrium tools is thus key for interpreting and planning tokamak experiments. We present here benchmarks and comparisons to experimental data of the EFIT++ reconstruction code (Appel et al., 2006), the free-boundary equilibrium code FREEBIE (Artaud and Kim, 2012), and a rapid plasma boundary reconstruction code VacTH (Faugeras et al., 2014). We demonstrate that FREEBIE can calculate the equilibrium and corresponding poloidal field (PF) coils currents consistently with EFIT++ reconstructions from experimental data. Both EFIT++ and VacTH can reconstruct equilibria generated by FREEBIE from synthetic, optionally noisy diagnostic data. Hence, VacTH is suitable for real-time control. Optimum reconstruction parameters are estimated.

An experimental study on the change of the radiosensitivity of several tumor cell lines and primary cultured gingi cal fibrobrast

International Nuclear Information System (INIS)

Lee, Sam Sun; You Dong Soo

1997-01-01

Radiation sensitivity data was generated for two human cancer cell lines (KB, RPMI 2650) and human primary gingival fibroblast was tested three times using a viable cell number counting with a hemocytometer, MTT (3-[4,5-dimethylthiazol 2-yl]-2,5-dipheny tetrazolium bromide) assay, and LDH (Lactate dehydrogenase) assay. Single irradiation of 2, 4, 6, 10, 15, 20 Gy were applied to the tumor cell lines and the primary cultured gingical fibroblast. The two fractions of 4 Gy an d 10 Gy were separated with a 4 hour time interval. The irradiation was done with 241.5 cGy/min dose rate using 137 Cs MK cell irradiator at room temperature. The obtained results were as followed : 1. There was significantly different viable cell numbers as the amount of radiation dose on the tested cells were cell number counted with a hemocytometer, In fractions, there were more viable cells remaining. 2. Phase-contrast microscopically, radiation-induced morphologic changes were pronounced on the tumor cells, however, almost no differences on the gingival fibroblast. 3. There was significantly different absorbance at 2 Gy on RPMI 2650, 4 Gy on KB and GF in MTT assay. In fractions, the absorbance was significantly higher on KB. 4. The level of extracellular LDH activity in the experimental group was significantly higher in the 2-4 Gy than the control group. 5. The total level of extracellular and intracellular LDH activity was decreased as increased amounts of radiation dose was applied.

Process Damping and Cutting Tool Geometry in Machining

Science.gov (United States)

Taylor, C. M.; Sims, N. D.; Turner, S.

2011-12-01

Regenerative vibration, or chatter, limits the performance of machining processes. Consequences of chatter include tool wear and poor machined surface finish. Process damping by tool-workpiece contact can reduce chatter effects and improve productivity. Process damping occurs when the flank (also known as the relief face) of the cutting tool makes contact with waves on the workpiece surface, created by chatter motion. Tool edge features can act to increase the damping effect. This paper examines how a tool's edge condition combines with the relief angle to affect process damping. An analytical model of cutting with chatter leads to a two-section curve describing how process damped vibration amplitude changes with surface speed for radiussed tools. The tool edge dominates the process damping effect at the lowest surface speeds, with the flank dominating at higher speeds. A similar curve is then proposed regarding tools with worn edges. Experimental data supports the notion of the two-section curve. A rule of thumb is proposed which could be useful to machine operators, regarding tool wear and process damping. The question is addressed, should a tool of a given geometry, used for a given application, be considered as sharp, radiussed or worn regarding process damping.

Process Damping and Cutting Tool Geometry in Machining

International Nuclear Information System (INIS)

Taylor, C M; Sims, N D; Turner, S

2011-01-01

Regenerative vibration, or chatter, limits the performance of machining processes. Consequences of chatter include tool wear and poor machined surface finish. Process damping by tool-workpiece contact can reduce chatter effects and improve productivity. Process damping occurs when the flank (also known as the relief face) of the cutting tool makes contact with waves on the workpiece surface, created by chatter motion. Tool edge features can act to increase the damping effect. This paper examines how a tool's edge condition combines with the relief angle to affect process damping. An analytical model of cutting with chatter leads to a two-section curve describing how process damped vibration amplitude changes with surface speed for radiussed tools. The tool edge dominates the process damping effect at the lowest surface speeds, with the flank dominating at higher speeds. A similar curve is then proposed regarding tools with worn edges. Experimental data supports the notion of the two-section curve. A rule of thumb is proposed which could be useful to machine operators, regarding tool wear and process damping. The question is addressed, should a tool of a given geometry, used for a given application, be considered as sharp, radiussed or worn regarding process damping.

The Tools Used by Science Teachers and Their Relevance to Objectives

Directory of Open Access Journals (Sweden)

Ulaş KUBAT

2018-01-01

Full Text Available The aim of this study is to reveal the views of science teachers on the use of tools in the learning-teaching process. Well-designed tools provide a rich learning environment. In this research qualitative research method was used. Semi-structured interview form was used as data collection tool. The working group consisted of 16 science teachers. According to the findings of the research, teachers use the most experimental materials as tools and teaching materials and 4 + 4 + 4 system creates problems for tools and materials. In addition, teachers have emphasized the problem of lack of material development. They indicated that well designed tools contribute to the achievement of objectives

Improving the quality of nurse clinical documentation for chronic patients at primary care clinics: A multifaceted intervention.

Science.gov (United States)

Mahomed, Ozayr H; Naidoo, Salsohni; Asmall, Shaidah; Taylor, Myra

2015-09-25

Deficiencies in record keeping practices have been reported at primary care level in the public health sector in South Africa. These deficiencies have the potential to negatively impact patient health outcomes as the break in information may hinder continuity of care. This disruption in information management has particular relevance for patients with chronic diseases. The aim of this study was to establish if the implementation of a structured clinical record (SCR) as an adjunct tool to the algorithmic guidelines for chronic disease management improved the quality of clinical records at primary care level. A quasi-experimental study (before and after study with a comparison group) was conducted across 30 primary health care clinics (PHCs) located in three districts in South Africa. Twenty PHCs that received the intervention were selected as intervention clinics and 10 facilities were selected as comparison facilities. The lot quality assurance sampling (LQAS) method was used to determine the number of records required to be reviewed per diagnostic condition per facility. There was a a statistically significant increase in the percentage of clinical records achieving compliance to the minimum criteria from the baseline to six months post-intervention for both HIV patients on antiretroviral treatment and patients with non-communicable diseases (hypertension and diabetes). A multifaceted intervention using a SCR to supplement the educational outreach component (PC 101 training) has demonstrated the potential for improving the quality of clinical records for patients with chronic diseases at primary care clinics in South Africa.

Micro-CT of Carotid Arteries: A Tool for Experimental Studies

International Nuclear Information System (INIS)

Mohr, Andreas; Wenke, Ruediger; Roemer, Frank W.; Lynch, John A.; Gatzka, Christian; Priebe, Markus; Guermazi, Ali; Grigorian, Mikayel; Heller, Martin; Mueller-Huelsbeck, Stefan

2004-01-01

Micro-computed tomography (micro-CT) is a high-resolution, nondestructive tool for two- and three-dimensional imaging and quantification. The ability of this technique to assess atherosclerosis of the carotid artery was evaluated in three human cadaver samples based on the original axial acquisitions, multiplanar reconstructions and volume rendering techniques. Quantitative analysis included the calculation of: (1) the original lumen perimeter, original lumen area, plaque area, residual lumen area, calcified area and gross sectional area reduction of the vascular lumen from two-dimensional slices; (2) the total tissue volume, soft tissue volume and calcified tissue volume from the three-dimensional data set. This preliminary study demonstrates the potential of micro-CT as a supplementary method for the two- and three-dimensional ex vivo evaluation of carotid atherosclerosis

Assessment of COPD wellness tools for use in primary care : an IPCRG initiative

NARCIS (Netherlands)

Cave, Andrew J.; Atkinson, Lana; Tsiligianni, Ioanna G.; Kaplan, Alan G.

2012-01-01

COPD is considered a complex disease and global problem that is predicted to be the third most common cause of death by 2030. While managing this chronic condition, primary health care practitioners are faced with the ongoing challenge of achieving good quality of life and overall "wellness" for

Diagnosing Mental Health Disorders in Primary Care: Evaluation of a New Training Tool

Science.gov (United States)

Satter, Rachel

2012-01-01

Major Depressive Disorder (MDD) and Posttraumatic Stress Disorder (PTSD) are highly prevalent illnesses that can result in profound impairment. While many patients with these disorders present in primary care, research suggests that physicians under-detect and suboptimally manage MDD and PTSD in their patients. The development of more effective…

Tree Transduction Tools for Cdec

Directory of Open Access Journals (Sweden)

Austin Matthews

2014-09-01

Full Text Available We describe a collection of open source tools for learning tree-to-string and tree-to-tree transducers and the extensions to the cdec decoder that enable translation with these. Our modular, easy-to-extend tools extract rules from trees or forests aligned to strings and trees subject to different structural constraints. A fast, multithreaded implementation of the Cohn and Blunsom (2009 model for extracting compact tree-to-string rules is also included. The implementation of the tree composition algorithm used by cdec is described, and translation quality and decoding time results are presented. Our experimental results add to the body of evidence suggesting that tree transducers are a compelling option for translation, particularly when decoding speed and translation model size are important.

Depression, quality of life and primary care: A cross-sectional study

Directory of Open Access Journals (Sweden)

Panos Andriopoulos

2013-12-01

Conclusion: The prevalence of both depressive symptomatology and impairment of quality of life is significant and primary care with simple, validated tools can be the setting for identifying and helping such patients.

Experimental Research in Operation Management in Engine Room by using Language Sentiment/Opinion Analysis

Directory of Open Access Journals (Sweden)

Dimitris Papachristos

2014-12-01

Full Text Available The paper argues for the necessity of a combination MMR methods (questionnaire, interview and sentiment/opinion techniques to personal satisfaction analysis at the maritime and training education and proposes a generic, but practical research approach for this purpose. The proposed approach concerns the personal satisfaction evaluation of Engine Room simulator systems and combines the speech recording (sentiment/opinion analysis for measuring emotional user responses with usability testing (SUS tool. The experimental procedure presented here is a primary effort to research the emotion analysis (satisfaction of the users-students in Engine Room Simulators. Finally, the ultimate goal of this research is to find and test the critical factors that influence the educational practice and user’s satisfaction of Engine Room Simulator Systems and the ability to conduct full-time system control by the marine crew.

Investigation of the Effect of Tool Edge Geometry upon Cutting Variables, Tool Wear and Burr Formation Using Finite Element Simulation — A Progress Report

Science.gov (United States)

Sartkulvanich, Partchapol; Al-Zkeri, Ibrahim; Yen, Yung-Chang; Altan, Taylan

2004-06-01

This paper summarizes some of the progress made on FEM simulations of metal cutting processes conducted at the Engineering Research Center (ERC/NSM). Presented research focuses on the performance of various cutting edge geometries (hone and chamfer edges) for different tool materials and specifically on: 1) the effect of round and chamfer edge geometries on the cutting variables in machining carbon steels and 2) the effect of the edge hone size upon the flank wear and burr formation behavior in face milling of A356-T6 aluminum alloy. In the second task, an innovative design of edge preparation with varying hone size around the tool nose is also explored using FEM. In order to model three-dimensional conventional turning and face milling with two-dimensional orthogonal cutting simulations, 2D simulation cross-sections consisting of the cutting speed direction and chip flow direction are selected at different locations along the tool nose radius. Then the geometries of the hone and chamfer edges and their associated tool angles as well as uncut chip thickness are determined on these planes and employed in cutting simulations. The chip flow direction on the tool rake face are obtained by examining the wear grooves on the experimental inserts or estimated by using Oxley's approximation theory of oblique cutting. Simulation results are compared with the available experimental results (e.g. cutting forces) both qualitatively and quantitatively.

BURT: back up and restore tool

Energy Technology Data Exchange (ETDEWEB)

Karonis, N.T.

1994-11-01

BURT is just one of the tools in the Experimental Physics Industrial Control System (EPICS). In this document we address the problem of backing up and restoring sets of values in databases whose values are continuously changing. In doing so, we present the Back Up and Restore Tool (BURT). In this presentation we provide a theoretical framework that defines the problem and lays the foundation for its solution. BURT is a tool designed and implemented with respect to that theoretical framework. It is not necessary for users of BURT to have an understanding of that framework. It was included in this document only for the purpose of completeness. BURT`s basic purpose is to back up sets of values so that they can be later restored. Each time a back up is requested, a new ASCII file is generated. Further, the data values are stored as ASCII strings and therefore not compressed. Both of these facts conspire against BURT as a candidate for an archiver. Users who need an archiver should use a different tool, the Archiver.

Micromilling of hardened tool steel for mould making applications

DEFF Research Database (Denmark)

Bissacco, Giuliano; Hansen, Hans Nørgaard; De Chiffre, Leonardo

2005-01-01

geometries as those characterizing injection moulding moulds. The realization of the micromilling process in connection with hardened tool steel as workpiece material is particularly challenging. The low strength of the miniaturized end mills implies reduction and accurate control of the chip load which...... wear. This paper presents the micromilling process applied to the manufacturing of micro injection moulding moulds in hardened tool steel, presenting experimental evidence and possible solutions to the above-mentioned issues....

Challenges in developing drugs for primary headaches

DEFF Research Database (Denmark)

Schytz, Henrik Winther; Hargreaves, Richard; Ashina, Messoud

2017-01-01

This review considers the history of drug development in primary headaches and discusses challenges to the discovery of innovative headache therapeutics. Advances in headache genetics have yet to translate to new classes of therapeutics and there are currently no clear predictive human biomarkers...... for any of the primary headaches that can guide preventative drug discovery and development. Primary headache disorder subtypes despite common phenotypic presentation are undoubtedly heterogeneous in their pathophysiology as judged by the variability of response to headache medicines. Sub......, despite having promising effects in basic pain models, have not delivered efficacy in the clinic. Future efforts may triage novel physiological mediators using human experimental models of headache pain to support drug discovery strategies that target active pathways pharmacologically....

CGRP in human models of primary headaches

DEFF Research Database (Denmark)

Ashina, Håkan; Schytz, Henrik Winther; Ashina, Messoud

2018-01-01

experiments are likely due to assay variation; therefore, proper validation and standardization of an assay is needed. To what extent CGRP is involved in tension-type headache and cluster headache is unknown. CONCLUSION: Human models of primary headaches have elucidated the role of CGRP in headache...... pathophysiology and sparked great interest in developing new treatment strategies using CGRP antagonists and antibodies. Future studies applying more refined human experimental models should identify biomarkers of CGRP-induced primary headache and reveal whether CGRP provocation experiments could be used......OBJECTIVE: To review the role of CGRP in human models of primary headaches and to discuss methodological aspects and future directions. DISCUSSION: Provocation experiments demonstrated a heterogeneous CGRP migraine response in migraine patients. Conflicting CGRP plasma results in the provocation...

Effect of education and training on patient referral by public primary ...

African Journals Online (AJOL)

A quasi-experimental study was carried out to determine the effect of health education and training on the Knowledge,attitude and practices of patient referral by primary health care workers in Mushin and Surulere Local Government Areas of Lagos State of Nigeria. Material and method: A total sample of 170 primary health ...

The emergence of modern statistics in agricultural science: analysis of variance, experimental design and the reshaping of research at Rothamsted Experimental Station, 1919-1933.

Science.gov (United States)

Parolini, Giuditta

2015-01-01

During the twentieth century statistical methods have transformed research in the experimental and social sciences. Qualitative evidence has largely been replaced by quantitative results and the tools of statistical inference have helped foster a new ideal of objectivity in scientific knowledge. The paper will investigate this transformation by considering the genesis of analysis of variance and experimental design, statistical methods nowadays taught in every elementary course of statistics for the experimental and social sciences. These methods were developed by the mathematician and geneticist R. A. Fisher during the 1920s, while he was working at Rothamsted Experimental Station, where agricultural research was in turn reshaped by Fisher's methods. Analysis of variance and experimental design required new practices and instruments in field and laboratory research, and imposed a redistribution of expertise among statisticians, experimental scientists and the farm staff. On the other hand the use of statistical methods in agricultural science called for a systematization of information management and made computing an activity integral to the experimental research done at Rothamsted, permanently integrating the statisticians' tools and expertise into the station research programme. Fisher's statistical methods did not remain confined within agricultural research and by the end of the 1950s they had come to stay in psychology, sociology, education, chemistry, medicine, engineering, economics, quality control, just to mention a few of the disciplines which adopted them.

Experimental tests on ratchet of structural elements diagrams for primary tension and secondary twist

International Nuclear Information System (INIS)

Lebey, J.; Roche, R.L.; Cousseran, P.

1980-05-01

Design by analysis of pressure vessels is not complete without an appraisal of failure by progressive distortion or stress ratchet. Ratchet tests under constant axial stress associated with cyclic torsion deformation have been carried out on 304 L and 316 L thin tubular specimens, at room temperature. Results are given in the form of iso-deformation curves ranging from 0.1% to 2.5%, in the field definite by the primary and secondary stress intensities (Bree's diagram type). The use of an effective primary stress is proposed, as a practical way, to assess the elongation due to the ratchet effect

A Simulation Tool for the Conceptual Design of Thermonuclear Pulsors

International Nuclear Information System (INIS)

Ramos, R.; Gonzalez, J.; Clausse, A.

2003-01-01

We worked with an effective model that calculates the neutron production of Plasma Focus devices.From experimental data we obtained different fitting functions for the model lumped parameters.By this way, we obtained a simple tool for neutron yield calculation.This tool is very useful at a conceptual design stage, because it can predict easily if a given PF device would be suitable for a certain application

Radiochemical tools at the experimental lakes area (ELA) in Ontario, Canada

International Nuclear Information System (INIS)

Pfitzner, J.; Brunskill, G.

1998-01-01

Full text: For over 20 years, Canadian research scientists have used radiochemical tracers added to remote and pristine lakes to study physical, chemical, and biological processes that could not be easily quantified by other methods. Lakes have also been manipulated by experimentally altering the hydrological cycle, chemical composition, and species of fish in selected lakes, and using companion lakes as controls. Varying additions of organic carbon, N, and P have been done, and the exchange rate of carbon dioxide between the atmosphere and water was estimated using radon evasion rates from radium spikes in the lake water. Multinuclide spikes were done to follow the path of mine waste elements through the food chain and sediment accumulation. Lakes were experimentally acidified with HCl and HNO 3 and H 2 SO 4 to simulate acid rain, and to study natural buffering capacity of the hydrological cycle. Some of this research has been used to legislate pollution control in the St. Laurence Great Lakes and across Canada and USA. ELA research team spirit has survived several forest fires, bear attacks on the kitchen, massive cut-backs in funding and reduction in staff of Fisheries and Ocean Canada

OHS Certification as Tool and Strategy in Labour Inspection

DEFF Research Database (Denmark)

Hendriksen, Kåre

Certification of Occupational Health and Safety as Tool and Strategy in Labour Inspection Presentation of the project Certification of Occupational Health and Safety as Tool and Strategy in Labour Inspection financed by Nordic Council of Ministers. The project has analysed the new role...... 18001. Especially in Denmark this is the case, where certified companies a. o. are exempt from primary inspection, a development that can be seen as a slight successive privatization of regulation and inspection. The focused has been the validity of certification regarding to OHS performance...

Experimental and theoretical studies on stainless steel transfer onto a TiN-coated cutting tool

Energy Technology Data Exchange (ETDEWEB)

Wiklund, U., E-mail: urban.wiklund@angstrom.uu.se [Applied Materials Science, Department of Engineering Sciences, Box 534, 751 21, Uppsala University (Sweden); Rubino, S. [Electron Microscopy and Nanoengineering, Department of Engineering Sciences, Box 534, 751 21, Uppsala University (Sweden); Kadas, K. [Materials Theory, Department of Physics and Astronomy, Box 516, 751 20, Uppsala University (Sweden); Research Institute for Solid State Physics and Optics, H-1525 Budapest, PO Box 49 (Hungary); Skorodumova, N.V.; Eriksson, O. [Materials Theory, Department of Physics and Astronomy, Box 516, 751 20, Uppsala University (Sweden); Hedberg, S. [Outokumpu Stainless AB, Box 74, 774 22 Avesta (Sweden); Collin, M. [AB Sandvik Tooling R and D, SE-126 80 Stockholm (Sweden); Olsson, A. [Angstroem Materials Academy, Box 534, 751 21, Uppsala University (Sweden); Leifer, K. [Electron Microscopy and Nanoengineering, Department of Engineering Sciences, Box 534, 751 21, Uppsala University (Sweden)

2011-01-15

Stainless steel is a good example of a metal that is not easily machined. To explain such behavior an understanding of the fundamental adhesion between the workpiece and the tool is invaluable. It is a well-known fact that build-up layers form in the interface, but little attention has been given to the very first layer that adheres to the tool surface. Although this layer rapidly becomes covered by successive material transfer, this layer and its ability to stick to the tool surface control the successive material transfer and influence the cutting properties. In this work, a quick stop test is employed to interrupt the cutting of a 316L stainless steel using a TiN-coated cemented carbide cutting insert. Different analytical techniques, such as transmission electron microscopy, X-ray photoelectron spectroscopy and scanning electron microscopy, as well as theoretical atomistic modeling, were used to study the early adhesion.

Experimental and theoretical studies on stainless steel transfer onto a TiN-coated cutting tool

International Nuclear Information System (INIS)

Wiklund, U.; Rubino, S.; Kadas, K.; Skorodumova, N.V.; Eriksson, O.; Hedberg, S.; Collin, M.; Olsson, A.; Leifer, K.

2011-01-01

Stainless steel is a good example of a metal that is not easily machined. To explain such behavior an understanding of the fundamental adhesion between the workpiece and the tool is invaluable. It is a well-known fact that build-up layers form in the interface, but little attention has been given to the very first layer that adheres to the tool surface. Although this layer rapidly becomes covered by successive material transfer, this layer and its ability to stick to the tool surface control the successive material transfer and influence the cutting properties. In this work, a quick stop test is employed to interrupt the cutting of a 316L stainless steel using a TiN-coated cemented carbide cutting insert. Different analytical techniques, such as transmission electron microscopy, X-ray photoelectron spectroscopy and scanning electron microscopy, as well as theoretical atomistic modeling, were used to study the early adhesion.

Studies of prehistoric flint tools by PIXE

International Nuclear Information System (INIS)

Smit, Z.

2002-01-01

The trace elements preserved on sharp edges of stone tools may provide some information about the worked material, which in turn may serve for the reconstruction of users way of life. Since the amount of the deposited worked material is minute, it can only be detected by sensitive fluorescence techniques, induced by electrons in the electron microscopes, or by light ions from the particle accelerators (PIXE). The trace element deposition was studied by PIXE for a set of experimental tools used for working bone and wood, and for a set of archaeological artefacts dating from the late paleolithic till neolithic period. (author)

The Measurement of Students' Achievement in Teaching Primary School Fifth Year Mathematics Classes

Science.gov (United States)

Doganay, Ahmet; Bal, Ayten Pinar

2010-01-01

The aim of this study was to investigate students' and teachers' point of views about preparing measurement tools used in mathematics classes, the level of learning that these tools are intended to measure, how often they are used and how they are scored in terms of assessing 5th grade primary school mathematic courses. The population of the study…

Microstructure and properties of powder metallurgy (PM) high alloy tool steels

International Nuclear Information System (INIS)

Wojcieszynski, A.L.; Eisen, W.B.; Dixon, R.B.

1998-01-01

Particle metallurgy (PM) processing is currently the primary manufacturing method used to produce advanced high alloy tool steel compositions for use in industrial tooling applications. This process involves gas atomization of the pre-alloyed melt to form spherical powders and consolidation by HIP to full density. The HIP product may be used directly in select applications, but is usually subjected to additional forging to improve properties and produce a wide range of bar and plate sizes. Compared to ingot-cast tool steels, PM tool steels have very homogeneous microstructures with very fine carbide and sulfide size distributions, free from carbide banding, which results in improved machinability, grindability, and mechanical properties. In addition, this technology enables the development of advanced tool steel compositions which could not be economically produced by conventional steelmaking. (author)

Forward impact extrusion of surface textured steel blanks using coated tooling

Science.gov (United States)

Hild, Rafael; Feuerhack, Andreas; Trauth, Daniel; Arghavani, Mostafa; Kruppe, Nathan C.; Brögelmann, Tobias; Bobzin, Kirsten; Klocke, Fritz

2017-10-01

A method to enable dry metal forming by the means of a self-lubricating coating and surface textures was researched using an innovative Pin-On-Cylinder-Tribometer. The experimental analysis was complemented by a numerical model of the complex contact conditions between coated tools and the surface textured specimen at the micro-level. Based on the results, the explanation of the tribological interactions between surface textured specimens and the tool in dry full forward extrusion is the objective of this work. Therefore, experimental dry extrusion tests were performed using a tool system. The extruded specimens were evaluated regarding their geometry as well as by the required punch force. Thereby, the effectiveness and the feasibility of dry metal forming on the example of full forward extrusion was evaluated. Thus, one more step towards the technical realization of dry metal forming of low alloy steels under industrial conditions was realized.

Cancer of unknown primary origin: a case report

Directory of Open Access Journals (Sweden)

Elisa De Carlo

2013-03-01

Full Text Available Carcinoma of unknown primary origin (CUP accounts for 2-10% of all malignancies. The apparent absence of the primary tumour, the development of early, uncommon systemic metastases and the resistance to therapy and poor prognosis are hallmarks of this heterogeneous clinical entity and are a challenge for physicians. The diagnostic workup of patients with CUP includes a large amount of histopathological examination, as well as the use of imaging techniques that often fail to identify the primary tumour. Therefore, the optimal workup and treatment for these patients remains to be determined. Molecular diagnostic tools, such as DNA microarray analysis, could help in the search for "lost" CUP origin and guide the further treatment approach. We report the case of a 66-year-old man, with mediastinal lymph nodes metastasis of carcinoma and neurological syndrome with diplopia and balance disorders, in which many exams have been performed without finding the primary tumour.

Investigation of wear land and rate of locally made HSS cutting tool

Science.gov (United States)

Afolalu, S. A.; Abioye, A. A.; Dirisu, J. O.; Okokpujie, I. P.; Ajayi, O. O.; Adetunji, O. R.

2018-04-01

Production technology and machining are inseparable with cutting operation playing important roles. Investigation of wear land and rate of cutting tool developed locally (C=0.56%) with an HSS cutting tool (C=0.65%) as a control was carried out. Wear rate test was carried out using Rotopol -V and Impact tester. The samples (12) of locally made cutting tools and one (1) sample of a control HSS cutting tool were weighed to get the initial weight and grit was fixed at a point for the sample to revolve at a specific time of 10 mins interval. Approach of macro transfer particles that involved mechanism of abrasion and adhesion which was termed as mechanical wear to handle abrasion adhesion processes was used in developing equation for growth wear at flank. It was observed from the wear test that best minimum wear rate of 1.09 × 10-8 and 2.053 × 10-8 for the tools developed and control were measured. MATLAB was used to simulate the wear land and rate under different conditions. Validated results of both the experimental and modeling showed that cutting speed has effect on wear rate while cutting time has predicted measure on wear land. Both experimental and modeling result showed best performances of tools developed over the control.

Staff perceptions of addressing lifestyle in primary health care: a qualitative evaluation 2 years after the introduction of a lifestyle intervention tool

Directory of Open Access Journals (Sweden)

Carlfjord Siw

2012-10-01

Full Text Available Abstract Background Preventive services and health promotion in terms of lifestyle counselling provided through primary health care (PHC has the potential to reduce morbidity and mortality in the population. Health professionals in general are positive about and willing to develop a health-promoting and/or preventive role. A number of obstacles hindering PHC staff from addressing lifestyle issues have been identified, and one facilitator is the use of modern technology. When a computer-based tool for lifestyle intervention (CLT was introduced at a number of PHC units in Sweden, this provided an opportunity to study staff perspectives on the subject. The aim of this study was to explore PHC staff’s perceptions of handling lifestyle issues, including the consultation situation as well as the perceived usefulness of the CLT. Methods A qualitative study was conducted after the CLT had been in operation for 2 years. Six focus group interviews, one at each participating unit, including a total of 30 staff members with different professions participated. The interviews were designed to capture perceptions of addressing lifestyle issues, and of using the CLT. Interview data were analysed using manifest content analysis. Results Two main themes emerged from the interviews: a challenging task and confidence in handling lifestyle issues. The first theme covered the categories responsibilities and emotions, and the second theme covered the categories first contact, existing tools, and role of the CLT. Staff at the units showed commitment to health promotion/prevention, and saw that patients, caregivers, managers and politicians all have responsibilities regarding the issue. They expressed confidence in handling lifestyle-related conditions, but to a lesser extent had routines for general screening of lifestyle habits, and found addressing alcohol the most problematic issue. The CLT, intended to facilitate screening, was viewed as a complement, but was not

[Adaptation of the Medical Office Survey on Patient Safety Culture (MOSPSC) tool].

Science.gov (United States)

Silvestre-Busto, C; Torijano-Casalengua, M L; Olivera-Cañadas, G; Astier-Peña, M P; Maderuelo-Fernández, J A; Rubio-Aguado, E A

2015-01-01

To adapt the Medical Office Survey on Patient Safety Culture (MOSPSC) Excel(®) tool for its use by Primary Care Teams of the Spanish National Public Health System. The process of translation and adaptation of MOSPSC from the Agency for Healthcare and Research in Quality (AHRQ) was performed in five steps: Original version translation, Conceptual equivalence evaluation, Acceptability and viability assessment, Content validity and Questionnaire test and response analysis, and psychometric properties assessment. After confirming MOSPSC as a valid, reliable, consistent and useful tool for assessing patient safety culture in our setting, an Excel(®) worksheet was translated and adapted in the same way. It was decided to develop a tool to analyze the "Spanish survey" and to keep it linked to the "Original version" tool. The "Spanish survey" comparison data are those obtained in a 2011 nationwide Spanish survey, while the "Original version" comparison data are those provided by the AHRQ in 2012. The translated and adapted tool and the analysis of the results from a 2011 nationwide Spanish survey are available on the website of the Ministry of Health, Social Services and Equality. It allows the questions which are decisive in the different dimensions to be determined, and it provides a comparison of the results with graphical representation. Translation and adaptation of this tool enables a patient safety culture in Primary Care in Spain to be more effectively applied. Copyright © 2014 SECA. Published by Elsevier Espana. All rights reserved.

Using XFRACAS as a PVROM database tool.

Energy Technology Data Exchange (ETDEWEB)

Hamman, Colin Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2014-04-01

ReliaSofts XFRACAS is a tool chosen by Sandia National Laboratories (SNL) for the purpose of collecting and organizing photovoltaic (PV) system field data that is to be used in assessing PV system reliability. It is a Web-based, closed-loop, incident (failure) reporting, analysis, and corrective action system software package designed for the acquisition, management and analysis of quality and reliability data from multiple sources. The ability to export PV system times-to-failure and times-to-suspension for ready analysis by ReliaSofts Weibull++ and RGA was a primary consideration in choosing XFRACAS as a reliability data collection tool.

Stagnant zone formation on diamond cutting tools during machining

International Nuclear Information System (INIS)

Izman, S.; Tamin, M.N.; Mon, T.T.; Venkatesh, V.C.; Shaharoun, A.M.

2007-01-01

Formation of an intact region on the rake face of cutting tool during machining is quite common phenomenon but its significance in maintaining tool edge sharpness has not been recognized by many researchers. This region is sometimes called stagnant zone. It is believed that when an intact zone present on the rake face, it delays the crater wear progress and hence maintaining the tool edge sharpness longer. This paper investigates the effect of edge radius, surface roughness of the rake face and cutting parameters on the formation of stagnant zone on two different type of diamond tools i.e. polycrystalline diamond PCD-KD100 and diamond-coated inserts when machining titanium alloy. The used inserta and post-processed chips were examined under FESEM and optical microscope after cutting at three different conditions. Experimental results show that the speed and feel, the tool edge radius, and the tool rake surface roughness significantly affect the stagnant zone formation. (author)

A Prospective Comparison of 18F-FDG PET/CT and CT as Diagnostic Tools to Identify the Primary Tumor Site in Patients with Extracervical Carcinoma of Unknown Primary Site

DEFF Research Database (Denmark)

Moller, Anne Kirstine H; Loft, Annika; Berthelsen, Anne K

2012-01-01

that the same set of criteria were used for classification of patients, that is, either as CUP patients or patients with a suggested primary tumor site. The independently obtained suggestions of primary tumor sites using PET/CT and CT were correlated with the SR to reach a consensus regarding true-positive (TP......), true-negative, false-negative, and false-positive results.Results. SR identified a primary tumor site in 66 CUP patients (48.9%). PET/CT identified 38 TP primary tumor sites and CT identified 43 TP primary tumor sites. No statistically significant differences were observed between (18)F-FDG PET...

assessment of the english literacy level of patients in primary health ...

African Journals Online (AJOL)

2010-09-07

Sep 7, 2010 ... The English literacy level of primary health care patients in Tshwane .... It is therefore important to use appropriate literacy assessment tools to .... Participants were given the following instruction: ..... One of the disadvantages.

Development of an interpretive simulation tool for the proton radiography technique

Science.gov (United States)

Levy, M. C.; Ryutov, D. D.; Wilks, S. C.; Ross, J. S.; Huntington, C. M.; Fiuza, F.; Martinez, D. A.; Kugland, N. L.; Baring, M. G.; Park, H.-S.

2015-03-01

Proton radiography is a useful diagnostic of high energy density (HED) plasmas under active theoretical and experimental development. In this paper, we describe a new simulation tool that interacts realistic laser-driven point-like proton sources with three dimensional electromagnetic fields of arbitrary strength and structure and synthesizes the associated high resolution proton radiograph. The present tool's numerical approach captures all relevant physics effects, including effects related to the formation of caustics. Electromagnetic fields can be imported from particle-in-cell or hydrodynamic codes in a streamlined fashion, and a library of electromagnetic field "primitives" is also provided. This latter capability allows users to add a primitive, modify the field strength, rotate a primitive, and so on, while quickly generating a high resolution radiograph at each step. In this way, our tool enables the user to deconstruct features in a radiograph and interpret them in connection to specific underlying electromagnetic field elements. We show an example application of the tool in connection to experimental observations of the Weibel instability in counterstreaming plasmas, using ˜108 particles generated from a realistic laser-driven point-like proton source, imaging fields which cover volumes of ˜10 mm3. Insights derived from this application show that the tool can support understanding of HED plasmas.

Advanced Tools for Smartphone-Based Experiments: Phyphox

Science.gov (United States)

Staacks, S.; Hütz, S.; Stampfer, C.; Heinke, H.

2018-01-01

The sensors in modern smartphones are a promising and cost-effective tool for experimentation in physics education, but many experiments face practical problems. Often the phone is inaccessible during the experiment and the data usually needs to be analyzed subsequently on a computer. We address both problems by introducing a new app, called…

Tuning of tool dynamics for increased stability of parallel (simultaneous) turning processes

Science.gov (United States)

Ozturk, E.; Comak, A.; Budak, E.

2016-01-01

Parallel (simultaneous) turning operations make use of more than one cutting tool acting on a common workpiece offering potential for higher productivity. However, dynamic interaction between the tools and workpiece and resulting chatter vibrations may create quality problems on machined surfaces. In order to determine chatter free cutting process parameters, stability models can be employed. In this paper, stability of parallel turning processes is formulated in frequency and time domain for two different parallel turning cases. Predictions of frequency and time domain methods demonstrated reasonable agreement with each other. In addition, the predicted stability limits are also verified experimentally. Simulation and experimental results show multi regional stability diagrams which can be used to select most favorable set of process parameters for higher stable material removal rates. In addition to parameter selection, developed models can be used to determine the best natural frequency ratio of tools resulting in the highest stable depth of cuts. It is concluded that the most stable operations are obtained when natural frequency of the tools are slightly off each other and worst stability occurs when the natural frequency of the tools are exactly the same.

Developing and Validating a New Classroom Climate Observation Assessment Tool.

Science.gov (United States)

Leff, Stephen S; Thomas, Duane E; Shapiro, Edward S; Paskewich, Brooke; Wilson, Kim; Necowitz-Hoffman, Beth; Jawad, Abbas F

2011-01-01

The climate of school classrooms, shaped by a combination of teacher practices and peer processes, is an important determinant for children's psychosocial functioning and is a primary factor affecting bullying and victimization. Given that there are relatively few theoretically-grounded and validated assessment tools designed to measure the social climate of classrooms, our research team developed an observation tool through participatory action research (PAR). This article details how the assessment tool was designed and preliminarily validated in 18 third-, fourth-, and fifth-grade classrooms in a large urban public school district. The goals of this study are to illustrate the feasibility of a PAR paradigm in measurement development, ascertain the psychometric properties of the assessment tool, and determine associations with different indices of classroom levels of relational and physical aggression.

Methods Developed by the Tools for Engine Diagnostics Task to Monitor and Predict Rotor Damage in Real Time

Science.gov (United States)

Baaklini, George Y.; Smith, Kevin; Raulerson, David; Gyekenyesi, Andrew L.; Sawicki, Jerzy T.; Brasche, Lisa

2003-01-01

Tools for Engine Diagnostics is a major task in the Propulsion System Health Management area of the Single Aircraft Accident Prevention project under NASA s Aviation Safety Program. The major goal of the Aviation Safety Program is to reduce fatal aircraft accidents by 80 percent within 10 years and by 90 percent within 25 years. The goal of the Propulsion System Health Management area is to eliminate propulsion system malfunctions as a primary or contributing factor to the cause of aircraft accidents. The purpose of Tools for Engine Diagnostics, a 2-yr-old task, is to establish and improve tools for engine diagnostics and prognostics that measure the deformation and damage of rotating engine components at the ground level and that perform intermittent or continuous monitoring on the engine wing. In this work, nondestructive-evaluation- (NDE-) based technology is combined with model-dependent disk spin experimental simulation systems, like finite element modeling (FEM) and modal norms, to monitor and predict rotor damage in real time. Fracture mechanics time-dependent fatigue crack growth and damage-mechanics-based life estimation are being developed, and their potential use investigated. In addition, wireless eddy current and advanced acoustics are being developed for on-wing and just-in-time NDE engine inspection to provide deeper access and higher sensitivity to extend on-wing capabilities and improve inspection readiness. In the long run, these methods could establish a base for prognostic sensing while an engine is running, without any overt actions, like inspections. This damage-detection strategy includes experimentally acquired vibration-, eddy-current- and capacitance-based displacement measurements and analytically computed FEM-, modal norms-, and conventional rotordynamics-based models of well-defined damages and critical mass imbalances in rotating disks and rotors.

Experimental and numerical study of the British Experimental Rotor Programme blade

Science.gov (United States)

Brocklehurst, Alan; Duque, Earl P. N.

1990-01-01

Wind-tunnel tests on the British Experimental Rotor Programme (BERP) tip are described, and the results are compared with computational fluid dynamics (CFD) results. The test model was molded using the Lynx-BERP blade tooling to provide a semispan, cantilever wing comprising the outboard 30 percent of the rotor blade. The tests included both surface-pressure measurements and flow visualization to obtain detailed information of the flow over the BERP tip for a range of angles of attack. It was observed that, outboard of the notch, favorable pressure gradients exist which ensure attached flow, and that the tip vortex also remains stable to large angles of attack. On the rotor, these features yield a very gradual break in control loads when the retreating-blade limit is eventually reached. Computational and experimental results were generally found to be in good agreement.

Effect of training intervention on primary health care workers ...

African Journals Online (AJOL)

Savannah Journal of Medical Research and Practice ... Design: A quasi experimental design, used multi stage sampling technique to select participants. ... Primary health care centers are fairly evenly distributed in all the 16 local government ...

[Blended-learning in psychosomatics and psychotherapy - Increasing the satisfaction and knowledge of students with a web-based e-learning tool].

Science.gov (United States)

Ferber, Julia; Schneider, Gudrun; Havlik, Linda; Heuft, Gereon; Friederichs, Hendrik; Schrewe, Franz-Bernhard; Schulz-Steinel, Andrea; Burgmer, Markus

2014-01-01

To improve the synergy of established methods of teaching, the Department of Psychosomatics and Psychotherapy, University Hospital Münster, developed a web-based elearning tool using video clips of standardized patients. The effect of this blended-learning approach was evaluated. A multiple-choice test was performed by a naive (without the e-learning tool) and an experimental (with the tool) cohort of medical students to test the groups' expertise in psychosomatics. In addition, participants' satisfaction with the new tool was evaluated (numeric rating scale of 0-10). The experimental cohort was more satisfied with the curriculum and more interested in psychosomatics. Furthermore, the experimental cohort scored significantly better in the multiple-choice test. The new tool proved to be an important addition to the classical curriculum as a blended-learning approach which improves students' satisfaction and knowledge in psychosomatics.

A dynamic simulation tool for the battery-hybrid hydrogen fuel cell vehicle

Energy Technology Data Exchange (ETDEWEB)

Moore, R.M. [Hawaii Natural Energy Institute, University of Hawaii, Manoa (United States); Ramaswamy, S.; Cunningham, J.M. [California Univ., Berkeley, CA (United States); Hauer, K.H. [xcellvision, Major-Hirst-Strasse 11, 38422 Wolfsburg (Germany)

2006-10-15

This paper describes a dynamic fuel cell vehicle simulation tool for the battery-hybrid direct-hydrogen fuel cell vehicle. The emphasis is on simulation of the hybridized hydrogen fuel cell system within an existing fuel cell vehicle simulation tool. The discussion is focused on the simulation of the sub-systems that are unique to the hybridized direct-hydrogen vehicle, and builds on a previous paper that described a simulation tool for the load-following direct-hydrogen vehicle. The configuration of the general fuel cell vehicle simulation tool has been previously presented in detail, and is only briefly reviewed in the introduction to this paper. Strictly speaking, the results provided in this paper only serve as an example that is valid for the specific fuel cell vehicle design configuration analyzed. Different design choices may lead to different results, depending strongly on the parameters used and choices taken during the detailed design process required for this highly non-linear and n-dimensional system. The primary purpose of this paper is not to provide a dynamic simulation tool that is the ''final word'' for the ''optimal'' hybrid fuel cell vehicle design. The primary purpose is to provide an explanation of a simulation method for analyzing the energetic aspects of a hybrid fuel cell vehicle. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Digital Story-Based Problem Solving Applications: Preservice Primary Teachers' Experiences and Future Integration Plans

Science.gov (United States)

Kilic, Çigdem; Sancar-Tokmak, Hatice

2017-01-01

This case study investigates how preservice primary school teachers describe their experiences with digital story-based problem solving applications and their plans for the future integration of this technology into their teaching. Totally 113 preservice primary school teachers participated in the study. Data collection tools included a…

Water quality control program in experimental circuits

International Nuclear Information System (INIS)

Cegalla, Miriam A.

1996-01-01

The Water Quality Control Program of the Experimental Circuits visualizes studying the water chemistry of the cooling in the primary and secondary circuits, monitoring the corrosion of the systems and studying the mechanism of the corrosion products transport in the systems. (author)

Prediction Of Abrasive And Diffusive Tool Wear Mechanisms In Machining

Science.gov (United States)

Rizzuti, S.; Umbrello, D.

2011-01-01

Tool wear prediction is regarded as very important task in order to maximize tool performance, minimize cutting costs and improve the quality of workpiece in cutting. In this research work, an experimental campaign was carried out at the varying of cutting conditions with the aim to measure both crater and flank tool wear, during machining of an AISI 1045 with an uncoated carbide tool P40. Parallel a FEM-based analysis was developed in order to study the tool wear mechanisms, taking also into account the influence of the cutting conditions and the temperature reached on the tool surfaces. The results show that, when the temperature of the tool rake surface is lower than the activation temperature of the diffusive phenomenon, the wear rate can be estimated applying an abrasive model. In contrast, in the tool area where the temperature is higher than the diffusive activation temperature, the wear rate can be evaluated applying a diffusive model. Finally, for a temperature ranges within the above cited values an adopted abrasive-diffusive wear model furnished the possibility to correctly evaluate the tool wear phenomena.